Faserbewehrter Beton wird heute zunehmend auch bei Tunnelbauwerken (Tunnelinnenschalen, Tubbinge) eingesetzt. Wesentliche Vorteile sind das hohe Tragvermogen, das daraus entstehende Einsparungspotential an herkommlicher stabformiger Bewehrung (Biegebewehrung, Bugelbewehrung in der Randzone), die Aufnahme von Spaltzugbeanspruchungen durch die Fasern, Rissbreitenbegrenzung, erhohte Dauerhaftigkeit, verbesserter Brandwiderstand (insbesondere bei Verwendung von Kunststofffasern), Optimierung der Arbeitsablaufe etc. Neue Entwicklungen in der Betontechnologie haben in den letzten Jahrzehnten den faserbewehrten ultrahochfesten Beton (engl. UHPFRC - Ultra High Performance Fibre Reinforced Concrete) hervorgebracht. Im Rahmen dieser Arbeit wird der Einsatz des ultrahochfesten, stahlfaserbewehrten Be...
The comprehensive survey explains the indications and the specific value of the modern tomographic modalities with respect to the various diagnostic issues. Numerous reproductions of CT, MRI, US scans illustrate the aspects discussed. (orig./CB) [German] Bildgebende Verfahren kommen bei der Abklaerung von Erkrankungen des weiblichen Urogenitaltrakts ergaenzend zu der klinischen Untersuchung zur Anwendung. Kongenitale Uterusanomalien werden primaer mit der HSG oder der Laparoskopie diagnostiziert. Zusaetzlich koennen der transvaginale US und in unklaren Faellen die MRT eingesetzt werden. Die Diagnose entzuendlicher Erkrankungen des weiblichen Genitaltrakts erfolgt in der Regel klinisch. Schnittbildverfahren werden bei therapieresistenten, komplizierten Faellen angewendet. Initial werden benigne Neoplasien des Uterus mit dem transvaginalen US abgeklaert. Eine Verdickung des Endometriums ist dabei ein unspezifischer Befund und ...
Meltdown and gasification of waste in an oxygen atmosphere ('2sv' process) is an economically efficient alternative to energetic and thermal utilisation of biomass. Organic pollutants are split at temperatures up to 2000 C in a reducing atmosphere. The process uses elements of the oxygen cupola furnace for melting and gasification of many different waste fractions, e.g. polluted waste wood, household refuse and bulk waste, old tyres, light shredder fractions, sewage sludge, etc. [German] Die Sauerstoff-Schmelz-Vergasung ('2sv') stellt eine wirtschaftliche Alternative zur energetischen Nutzung von Biomassen wie auch zur thermischen Abfallverwertung dar. Organische Schadstoffe werden bei diesem neuen Verfahren bei Temperaturen bis zu 2000 C unter reduzierenden Bedingungen aufgespalten. Das Verfahren nutzt Elemente des Sauerstoff-Kupolofens fuer die Schmelzvergasung und ...
In addition to dependable starting - even at extreme sub-zero temperatures - the starting behaviour of modern commercial vehicle diesel engines is increasingly being evaluated on the basis of HC emissions in the starting and warm-up phases. To improve their performance in this respect, most small and medium-sized diesel engines (with a capacity of 3 to 12 litres) are therefore equipped with intake air heating systems. As an alternative to high-performance, fuel-burning flame start systems, the automotive industry supplier Beru has now developed a new type of self-regulating electric heating element which not only ensures dependable starting with short heating times but also allows drastic reductions in HC emissions. (orig.) [Deutsch] Das Startverhalten moderner Nutzfahrzeug-Dieselmotoren wird, ergaenzend zum Hauptmerkmal des sicheren Starts auch bei extremen Minustemperaturen, zunehmend anhand der HC-Emission in der Start- und Warmlaufphase beurteilt. ...
Zusammenfassung Das Konzept der ?quivalenten Spannung (Vergleichsspannung) wird seit langem angewendet und hat sich bew?hrt. Ein wesentlicher Grund daf?r liegt darin, dass es u.?a. bei der Formulierung ph?nomenologischer Werkstoffmodelle weiterhilft. Von Nachteil ist, dass es weder mit physikalischen Prinzipien in Verbindung steht, noch Informationen ?ber die Mikrostruktur des Werkstoffs enth?lt. Trotzdem wurden zahlreiche Hypothesen zur Formulierung von ?quivalenten Spannungen in der Vergangenheit aufgestellt und in der Praxis mit unterschiedlichem Erfolg angewendet. Als Basis f?r die Systematisierung der zahlreichen Modelle hat Yu die Unified Strength Theory (UST) vorgeschlagen. Diese eignet sich, u.?a. inkompressibles inelastisches Materialverhalten sowie kompressible Werkstoffe mit unt...
The isothermal flow field for the axial cyclone has been experimentally determined. The velocity fields are used for determination particle paths (particle removal and suspended state), and inter alia of heat and mass transfer processes in the axial cyclone combustion chamber. The results are extremely significant as input value approximations for mathematical modelling, since experimentally obtained results are indispensable for complex flows and geometries. (orig.) [Deutsch] Es ist fuer den Axialzyklon experimentell das isotherme Stroemungsfeld ermittelt. Die Geschwindigkeitsfelder dienen zur Ermittlung der Partikelbahnen (Partikelabscheidung, Schwebebedingung), der Waerme- und Stoffuebertragungsprozesse u.a. in der Axialzyklonbrennkammer. Die Ergebnisse sind als Startwertnaeherung bei einer mathematischen Modellierung sehr wichtig, da bei komplexen Stroemungen und Geometrien versuchstechnische Ergebnisse unumgaenglich ...
Clinical studies have proved the effectiveness of local ablading methods in pations with non-resectable liver metastases of a colorectal carcinoma. RF ablation and LITT are a potentially curative therapy option and an alternative to systemic chemotherapy; the latter is carried out primarily for reducing tumour size with the goal of secondary resectability. The number of R0-sesectable metastases can be enhanced by a combined therapy of surgery and local ablading methods, e.g. by preoperative, intraoperative or postoperative ablasion of further non-resectable tumours during surgery. Systemic chemotherapy combined with surgery as an adjuvant method is not recommended unless in cases of non-abladable tumour recidivation. Currently, systemic chemotherapy is used as a neo-adjuvant therapy for tumour size reduction with the goal of secondary resectability or, in case of inoperability, local ablation. (orig.) [German] Abladierende Verfahren. Klinische Studien belegen die Effektivitaet der ...
The author investigates whether waste fermentation is an economically feasible alternative to composting. Decisions on projects and sites should not be made until the basic problems of feasibility and economic efficiency are solved. [German] In Anbetracht der derzeitigen Situation bei der Restmuellbehandlung, in der die mechanisch-biologische Behandlung als Alternative zu einer rein thermischen Behandlung immer mehr an Bedeutung gewinnt, stellt sich immer haeufiger die Frage, ob die Restmuellvergaerung eine Alternative zur ausschliesslichen Restmuellrotte darstellt. Diese Frage muss zunaechst prinzipiell aus Sicht der technischen Machbarkeit und von der Sinnhaftigkeit, hier vor allem von der Kostenseite her, betrachtet werden. Erst daran anschliessend lassen sich projekt- und standortbezogene Betrachtungen anstellen. Hinsichtlich der technischen Machbarkeit laesst sich im wesentlichen auf den grosstechnischen Erfahrungen der letzten 8 Jahre ...
There is much interest worldwide in low-emission, low-noise electric cars. Modern vehicles with advanced technology are an interesting alternative to conventional cars. (orig.) [Deutsch] Das Interesse an den emissionsfreien und leisen Elektroautos ist weltweit ungebrochen. Die heute verfuegbaren Fahrzeuge zeigen die betraechtlichen, in den letzten Jahren erzielten Fortschritte, die sie fuer immer mehr Anwender zu einer beliebten Alternative zur Benutzung des konventionellen Autos machen. (orig.)
In the well-known devices for increasing the decontamination factor in the treatment of radioactive waste water by evaporation, which consist of narrowing devices with evaporator sump and condenser, droplets of liquid and solid particles are carried over from the breeder space, which are radioactive and therefore make the decontamination factor worse. Better results are obtained if one places a fibre bed filter between the evaporator sump and the condenser, preferably in a horizontal connecting pipe between the evaporator sump and the condenser.
A new emissivity measurement device with inductive sample heating is described. The disc shaped samples can be measured between 800 C and 2000 C in vacuum or in each available gas atmosphere. Two kinds of surface temperature measurement methods are described, one by measuring in a blackbody hole and one by measuring at the surface without additional measures to correct emissivity. Total normal and spectral emissivity at wavelengths between 0,5 {mu}m and 8,3 {mu}m of various high temperature materials like platinum and Pt-Rh-alloys, siliconcarbide and molybdenum disilicide have been measured. From the investigated materials a few have been selected as reference samples for comparative emissivity measurements fullfilling the requirement of stability on air up to 400 C to 1000 C in order to ensure reproducibility of the results at different measurement conditions in air and in vacuum. (orig.) [Deutsch] Der Aufbau einer neuen Messapparatur fuer Emissionsgradmessungen ...
A high-temperature flow reactor and different technical plants were tested within the framework of this research project. Anthropogenic N{sub 2}O emissions form during secondary flue gas or waste gas purification as secondary emissions during denitrification and pollution abatement measures. N{sub 2}O forms as an intermediate product as NO is reduced to N{sub 2}. Under certain operating conditions N{sub 2}O is not decomposed completely. Different secondary flue gas purification measures, i.e. selective noncatalytic reduction (SNCR), selective catalytic reduction (SCR), and nonselective catalytic reduction (NSCR) were investigated testing several technical plants and the high-temperature flow reactor. (orig./EF) [Deutsch] Das Forschungsprojekt ``Messung der N{sub 2}O-Emissionen von Verbrennungsanlagen und Untersuchung von Moeglichkeiten zur Emissionsminderung`` wurde an einem Hochtemperatur-Stroemungsreaktor und an verschiedenen technischen Anlagen durchgefuehrt. ...
A process model is presented and used for identifying options for controlling the cupola furnace process and for investigating natural gas substitutes. Fuel substitution will affect temperature curves (i.e. tapping temperatures and melting capacity), outlet temperatures and gas mass flow out of the preheating zone. The contribution presents several process variations to overcome these problems and compares them with the natural gas process. [German] Mit dem Prozessmodell werden zunaechst Moeglichkeiten der Steuerung von Abstichtemperatur und Schmelzleistung, insbesondere unter Beruecksichtigung der Schrottqualitaet (spezifische Oberflaeche a{sub G}), untersucht. Es wird gezeigt, dass das Prozessmodell die Ergebnisse aus der Praxis wiedergibt. Daran anschliessend wird mit dem Prozessmodell die Substitution von Erdgas durch minderwertige Gase untersucht (Brennstoffsubstitution, Ressourcenschonung). Durch die Brennstoffsubstitution veraendern sich die Temperaturverlaeufe und damit auch ...
The MRI morphology in combined subacute degeneration has only rarely been reported. We describe two patients suffering from subacute combined degeneration of the spinal cord on the basis of a deficiency of vitamin B{sub 12}. In both patients characteristic hyperintense areas on T{sub 2}-weighted images in the posterior columns of the cervical and thoracic cord without contrast enhancement were demonstrated by MRI. (orig.) [Deutsch] Bisher liegen zur wenige Beschreibungen der MR-Morphologie bei funikulaerer Myelose vor. Wir beschreiben zwei Patienten mit den klinischen Zeichen einer funikulaeren Myelose auf der Basis eines Vitamin B{sub 12}-Mangels. Bei beiden konnten mit der MRT charakteristische Signalanhebungen im T{sub 2}-gewichteten Bild in den Hinterstraengen des zervikalen und thorakalen Rueckenmarks gezeigt werden. Eine Kontrastmittelaufnahme war nicht nachweisbar. (orig.)
CT-Expo is a novel MS Excel application for assessing the radiation doses delivered to patients undergoing CT examinations, based on computational methods that were used to analyze the data collected in the German survey on CT practice in 1999. The program enables the calculation of all dose quantities of practical value, such as axial dose free-in-air, weighted CTDI, dose-length product, effective dose and uterine dose. In contrast to existing programs for CT dose assessment, CT-Expo offers a number of unique features, such as gender-specific dose calculation for all age groups (adults, children, newborns), applicability to all existing scanner models including correction of scanner-specific influences, and the possibility of comparison with the results from the German CT survey on CT practice. Three different application modules offer free and standardized dose calculations as well as a comprehensive benchmarking section including guidance on dose optimization. The program is ...
Economic and safe operation of nuclear power plants requires reliable steam turbines with high efficiencies. The progress in flow mechanics achieved over the past few years has allowed the use of powerful methods of flow calculation in developments of new blading with greatly enhanced efficiencies. Thanks to the latest manufacturing techniques, the newly developed blading systems can be produced at low cost. Next to progress in flow mechanics, also the broadbased use of advanced finite-element calculations resulted in a more thorough grasp of the many problems associated with structural mechanics assessment of steam turbine components. The theoretical methods have been supplemented by comprehensive efforts in fracture mechanics and experimental materials studies, thus helping to create a reliable knowledge base which will help to avoid the dreaded stress corrosion cracking phenomenon, in components of steam turbines. The measures introduced to improve operational reliability already in ...
High temperature components of power plants are in many cases subjected to variable loading conditions such as cyclic creep or strain cycling. Therefore the cyclic behaviour of important heat resistant steels has been investigated under stress control and to a smaller extent under strain control. The behaviour under cyclic creep rupture conditions was determined in long term experiments covering a wide range of loading conditions. This behaviour can be described with the modified life fraction rule and a factor concept of relative life for single stage cycles and additionally with a multistep hypothesis for multi-stage cycles. The description can be adapted to estimate the life consumption under service type random conditions. The strain cycling behaviour was investigated in regard to the conditions of the heated surface of large components. To simulate this type of loading and to generate long term creep fatigue data, a service type strain cycle was developed. Anisothermal and ...
Early in 1988 RWE decided to overhaul the power station at Goldenberg. This was necessary due to the age of the plant, the obligation to supply heat and process steam and recent amendments of environmental legislation. After analysing demands and needs one developed a plant concept with a 290 t/h and a 400 t/h steam generator. Due to lack of space the decision was made in favour of a circulating atmospheric fluidised bed combustion instead of steam generators with pulverised lignite combustion as these steam generators take up much more space due to the legally required desulphurisation plants for gaseous emissions. Apart from generating steam RWE wishes to gain experience with this combustion technology and test it for suitability and use in large-scale plant. (orig./KO) [Deutsch] Aufgrund des fortgeschrittenen Alters, der aktuellen Umweltschutzgesetzgebung sowie bestehender Versorgungsverpflichtungen fuer Waerme und Prozessdampf wurde Anfang 1988 von der RWE Energie AG in Essen die ...
In view of current trends in motor car development, the author investigates the increasing conflict between higher comfort and lower fuel consumption. The conflict results mainly from insufficient cooling water heating with consumption-optimized engines. So far, it was never necessary to analyze heat flow after cold starting and heat-up of the powertrain, to develop strategies for heat storage and distribution, to remove heat sinks and to use components multifunctionally. The contribution shows that a general heat management strategy for the whole vehicle will result in high potential fuel savings and improved thermal comfort. Using the example of a latent heat store, heating strategies for the engine and transmission system on the one hand and the passenger compartment on the other hand are developed, and the advantages are presented in detail. [German] Abgeleitet aus den Trends in der Fahrzeugentwicklung wird auf den immer staerker werdenden Konflikt zwischen den steigenden ...
{gamma} Ti-Al have a higher temperature potential than commercial titanium alloys and a 50 percent lower density than nickel base superalloys. Application temperatures in aircraft turbines are 750 C and above. The authors investigated the high-temperature performance of {gamma} TiAl, i.e. isothermal high-temperature fatigue and the type and importance of damage. LCF experiments were made in the temperature range of brittle/ductile transition in air and vacuum. Damage mechanisms were characterized by microstructural investigations. [German] Unter den modernen Hochtemperaturwerkstoffen kommt den Legierungen auf Basis von {gamma}-TiAl eine zunehmend wichtige Bedeutung zu, da diese Werkstoffe ein hoeheres Temperaturpotential als alle kommerziellen Titanlegierungen haben und eine im Vergleich zu den Nickelbasis-Superlegierungen um ca. 50% geringere Dichte aufweisen. TiAl-Werkstoffe, die z.B. fuer Schaufeln und Gehaeuse in Flugzeugturbinen eingesetzt werden sollen, muessen ...
Today electric power steering systems are regularly considered by the car manufacturers as an alternative to a conventional hydraulic power steering system in the development of new vehicle platforms. Simplified vehicle assembly and the potential to contribute to the reduction of the vehicle's energy consumption are the main motivation for this. The performance of the systems available at present with 13.5 V supply voltage will be improved even more as soon as the future 42 V vehicle electrical systems are available. Like most active chassis systems, electric power steering has to meet the highest safety requirements imaginable. This article summarizes the safety philosophy of the TRW rack drive Electric Power Steering system. (orig.) [German] Elektromechanische Servolenkungen werden heute bei der Entwicklung neuer Fahrzeuge als Alternative zur konventionellen hydraulischen Servolenkung in Betracht gezogen. Die vereinfachte ...
Purpose: calculation of conversion coefficients for the reconstruction of organ doses from entrance doses for abdomen radiographs of 0, 1, 5, 10, 15, and 30-year-old patients in conventional pediatric radiology for the radiographic settings recommended by the German and European guidelines for quality management in diagnostic radiology. Materials und method: using the commercially available personal computer program PCXMC developed by the Finnish Center for Radiation and Nuclear Safety (Saeteilyturvakeskus STUK), conversion coefficients for conventional abdomen radiographs were calculated performing Monte Carlo simulations in mathematical hermaphrodite phantom models describing patients of different ages. The possible clinical variation of beam collimation was taken into consideration by defining optimal and suboptimal radiation fields on the phantoms' surfaces. Results: conversion coefficients for the reconstruction of organ does in about 40 organs and tissues of the human ...
Modern oscillation- and analysis systems are often mentioned in the context of oscillation diagnosis which implies that this is a method of establishing the causes of the mechanical changes that cause the unwanted oscillation. Experience shows, however, that oscillation monitoring instruments can merely indicate oscillation symptoms at an early point in time. These findings must be interpreted in a machine-specific way and seen in the context of previous developments in order to establish the mechanical root cause of the matter. A 1000 MVA-generator shows that conventional oscillation measuring systems may also serve for diagnostic purposes within certain limits.(orig.) [German] Im Zusammenhang mit modernen Schwingungsmess- und Analysensystemen wird haeufig der Begriff der Schwingungsdiagnose verwandt und inpliziert, damit auch die Ursache von mechanischen Veraenderungen finden zu koennen, welche das beanstandete Schwingungsverhalten hervorruft. In der Praxis zeigt sich, dass dem Stand ...
Flow Tex and ABB Energiekabel GmbH have developed a technique which allows the recovery of cables without requiring any trenching works. The new technique was successfully used for the first time for a pilot project in 1995. The authors report on two recent recovery projects (1998) in which an optimised technology was used for recovering a total of 1 500 m system length of 110 kV low-pressure oil-filled cables in Stuttgart and Munich on very different conditions. The authors describe the operational experiences with the cable connections and highlight the background stipulating the removal of the cables. (orig.) [Deutsch] Ein Verfahren zur grabungsfreien Bergung von Kabeln, gemeinsam entwickelt von FlowTex und ABB Energiekabel, wurde erstmals in einem Pilotprojekt 1995 mit Erfolg eingesetzt. Die Verfasser berichten ueber zwei Bergungsprojekte, bei denen 1998 mit der optimierten Technik in Stuttgart und Muenchen insgesamt 1 500 Systemmeter ...
Basic research in relation to a complete utilisation of animal substances as an alternative to a thermal disposal was done. The composition of different kinds of bones were investigated as well as their amounts which are available. Conventional utilisation was opposed to the innovative utilisation. Technologies will be selected which should be developed, because they have the chance in the case of a fast industrial realisation to get a good profit. There is a global requirement for the technologies which are developed and their products which can be produced with this. The raw material basis is available in the necessary scale in nearly all countries. (orig.) [German] Grundlegende Untersuchungen zur ganzheitlichen Verwertung von tierischen Substanzen als Alternative zur thermischen Entsorgung wurden durchgefuehrt. Es wurde die Zusammensetzung der verschiedenen Knochenarten und ihr Aufkommen untersucht. Die konventionelle wurde der innovativen ...
Endoluminal vascular prostheses that can be implanted by percutaneous routes represent the most recent development in vascular interventional radiology. Various commercially available types of prosthesis are presented and the construction principles and applications are described. At present secure indications for the implantation of endoluminal prostheses are limited to the elimination of aneurysms and arteriovenous fistulae of the large vessels near the trunk in sections that do not cross a joint. The wide use in peripheral occlusive diseases cannot yet be recommended because confirmed data are not available. (orig.) [German] Endoluminale Gefaessprothesen, die perkutan implantierbar sind, stellen die juengste Entwicklung in der vaskulaeren interventionellen Radiologie dar. Verschiedene kommerziell erhaeltliche Prothesentypen werden vorgestellt, ihr Konstruktionsprinzip und ihre Applikation erlaeutert. Die gesicherten Indikationen zur endoluminalen ...
By using defined compositions based on industrial wastes of the hard-coal mining and a further waste material (red mud), which is obtained during the extraction process of alumina (BAYER-Process), it is possible to produce expanded-clay granulate requiring suitable preparation, shaping and firing at temperatures of about 1150 C. Some of the investigated parameters and aspects of this manufacturing process will be presented in this paper. (orig.) [German] Aus definierten Mischungen industrieller Reststoffe des Steinkohlenbergbaus (Bergematerial) mit einem weiteren Abfallstoff (Rotschlamm), der bei der Aluminiumoxidgewinnung nach dem BAYER-Verfahren anfaellt, laesst sich nach geeigneter Aufbereitung und Formgebung durch Brennen bei ca. 1150 C Blaehton-Grunulat herstellen. Auf einen Teil der untersuchten Parameter und ermittelten Zusammenhaenge soll im folgenden naeher eingegangen werden. (orig.)
The stirling cryocooler ILK 15 is a machine with simple drive concept. This machine works with a conventional built-in electric motor and crank drive and needs a power input of about 500 W. The refrigerating capacity is 15 W at 80 K with a cooldown time of 12 minutes. The cooler is somehow a replacement for the Gifford-McMahon cycle coolers, which are bigger and heavier. The Stirling cryocooler was designed to cool HTSC-components. (orig.) [Deutsch] Der Stirlingkuehler ILK 15 ist eine Kaeltemaschine mit einfachem Antriebskonzept. Die Maschine arbeitet mit einem konventionellen Elektroeinbaumotor und Kurbeltrieb. Sie benoetigt eine Antriebsleistung von 500 W und hat eine Kaelteleistung von 15 W bis 80 K und eine Einkuehlzeit von 12 Minuten. Die Maschine kann als Alternative zur wesentlich groesseren und schweren Gifford-McMahon-Maschine gesehen und bei der Kuehlung von HTSL-Komponenten eingesetzt werden. (orig.)
Verification of guarantees mostly calls for measurements on the spot. The paper deals with the guarantees that apply to small hydroelectric power stations. Already when planning a plant it should be decided what guarantees are to be demanded and how they can be verified. Specifically, measurements to verify guaranteed performance and efficiency on the spot are dealt with. Details are not given. Rather, the report wants to give an overview of methods and aspects to be taken heed of. For in-depth information, the reader is referred to the corresponding standards and guidelines. (orig.) [Deutsch] Zur Ueberpruefung von Garantien ist meistens die Durchfuehrung von Messungen vorort notwendig. Es werden die Garantien behandelt, die bei Kleinwasserkraftanlagen in Frage kommen. Bereits bei der Planung der Anlage sollte entschieden werden, welche Garantien gefordert werden sollen und wie sie ueberprueft werden koennen. Es wird ...
For the preparation of photonic probes for hadron physics the determination of energy and polarization of the photons is essential. In this dissertation in a first part a possibility of the determination of the degree of polarization by use of the asymmetry observables is presented. In a second part a possibility isd discussed to perform an energy and polarization tagging of nearly real photons in electron scattering under small Q{sup 2}. By this method it should be possible to tag billions of photons per second.
By tests about pipe failure under extreme bending, moment at cross sections affected by circumferential cracks, admissible strains for securing the integrity in the area of a flow link are indicated. These are 7% for austenic and ferritic materials in the undisturbed cross section. From d/t-ratios of 20 onwards the strains are limited by pipe bulging on the pressure-load side. In this connection, circumferential flaws do not have any influence on the behaviour on the strained side, when their expansion does not exceed the investigated limitis of <60 circumferential expansion and crack depth of 0,3 t. (orig.)
Two isothermal sections were prepared at 1000 and 1150 C showing the low-Zr phases of the system Fe-Al-Zr. The phase equilibria were determined by means of X-ray powder diffractometry and electron beam microanalysis. For initial characterisation of mechanical properties, hardness values are determined and added to the tabulated data. (orig./MM) [German] Es werden am Fe-Al-Zr-System zwei isotherme Schnitte durch den zirkoniumarmen Teil des Systems bei 1000 und 1150 C erstellt. Die auftretenden Phasengleichgewichte werden mit Hilfe der Roentgenpulverdiffraktometrie und Elektronenstrahlmikroanalyse aufgeklaert. Zusaetzlich werden zur ersten Charakterisierung der mechanischen Eigenschaften Haertewerte bestimmt.
On 10 dialysis patients we performed 12 balloon dilatations, 2 catheter lyses, 6 stent implants (Palmaz stent) and one atherectomy of central venous stenoses or occlusions (v. subclavia, v. brachiocephalica) at the shunt arm of the patient. The primary success rate was, in balloon PTA and lysis, 12/14 interventions, and in stent placement and atherectomy 7/7. The angiographical and clinical primary result after stent implantation was significantly better than after conventional dilatation. After 66% of the balloon dilatations recidivation occurred within the first year; this can be treated by means of repeated PTA. Whether long-term exclusion of recurrence can be achieved by stent implantation, must be established by means of follow-up studies that are at present in progress. (orig.).
In rare cases, large adrenal masses with a suspicion of malignancy exhibit tumor extension into the adrenal vein and inferior vena cava. When planning surgery, the relationship of the extension to the inferior vena cava is of decisive improtance. We describe in two cases on the detection of a tumor thrombus in the inferior vena cava arising from a malignant adrenal mass by means of MR angiography (TOF, coronary 2D GRE images [FLASH], 3 slices acquired during 15 second apnea). The angiograms correlated well with the results of DSA venacavography and with the intraoperative findings. Thus, MRA has been demonstrated to be suitable for the certain proof of a venous tumor thrombus not only in cases of renal cell carcinomas but also in cases of malignant adrenal masses. The method should be applied whenever there is evidence of a venous involvement in the adrenal MR images. (orig.) [Deutsch] Grosse malignomverdaechtige Nebennierentumoren zeigen in seltenen Faellen eine Tumorausdehnung in die ...
Purpose: The nint version of the licensing regulation for medical doctors (Approbation Regulation (AR)) sets a benchmark in terms of practical experience, interdigitation of preclinical and clinical studies, interdisciplinary approach, economic efficiency, independence of students, added new teaching and learning modalities, and ongoing evaluation of the progress of the medical students. It is the aim to implement these major points of the AR in a model course for diagnostic radiology and radiation protection within the scope of the Virtual University of Bavaria and test them in practice. Materials and Methods: In cooperation with residents and board certified radiologists, students developed the virtual course 'Web-Based Training (WBT) Radiology' in diagnostic radiology and radiation protection for students in the first clinical semester. A representative target group taken from the student body was asked about the options to get access to the World Wide Web ...
With the development of the latent heat store and its inclusion in the conventional heating control of cars, success has been achieved both in increasing comfort and in making an important contribution to safety of driving. Great store is set in development of the system on its environmental friendliness, for example by the thorough use of environmentally friendly and reusable materials. This also means the use of clean materials. It was shown that the latent heat store (apart from the aspects of comfort and safety of driving) can also make a contribution to saving fuel and reducing the exhaust gas. The sum total of the advantages makes it clear that the latent heat store introduced here is a very environmentally friendly system with multi-functional properties. (orig.) [Deutsch] Mit der Entwicklung des Latentwaermespeichers und seiner Einbindung in die konventionelle Heizungsregelung von Automobilen ist es gelungen, sowohl den Komfort deutlich zu erhoehen als auch einen wichtigen ...
The fibre reinforcement of ceramic materials is used above all to improve the toughness and tolerance of damage, compared to unreinforced monolithic ceramics. This improvement is made possibly by the bridging effect of the cracks by the fibres in crack propagation in the matrix. In this work, the crack bridging effect of the fibres is included in a bridge stress equation, in which a clear relationship between bridge stress and crack opening is determined. The most important step for deriving the bridge stress law was determining the probability of failure of a fibre for a given axial stress curve. One relied on the micromechanical analysis of Hutchinson and Jensen here, by which the boundary conditions in multi-fibre materials can be included and realistic assumptions can be made for the load transfer mechanisms in the fibre/matrix boundary surface. (orig./MM) [Deutsch] Die Faserverstaerkung keramischer Werkstoffe dient vor allem zur Verbesserung der Zaehigkeit und ...
A part of the waste materials arising in iron and steel manufacture is utilised physically, either internally for the recovery of iron or externally for the production of cement and nonferrous metals. Most of these materials can be used without prior processing. Iron and steel-relevant waste materials which at present are still landfilled or disposed of as hazardous wastes are not immediately suitable for physical recycling as secondary raw material. These waste materials have to be processed without exception before they can be used again in the existing steel and iron manufacturing plants. The results of the authors` own studies have clearly shown that the cupola furnace is suited for the use of a wide variety of waste materials. [Deutsch] Ein Teil der bei der Eisen- und Stahlerzeugung anfallenden Abfallstoffe werden entweder intern zur Rueckgewinnung des Eisens oder extern in der Zement- bzw. Nichteisenmetallgewinnung stofflich verwertet. ...
The basis of assessment for particulate exhaust emissions is the gravimetric analysis of the particle concentration of diluted exhaust gases at temperatures below 52 C. This is very time consuming and takes sufficient sensitivity at low particulate emission rates like downstream of particle filters. For this reason the C/S-method, based on the thermographic analysis of carbon and sulfur, has been developed as an alternative to the gravimetric anallysis. This method yields particle mass as well as the main particle compounds. Comparisons between both methods have been carried out for heavy duty and automobile diesel engines as well as road vehicles and large diesel engines. The tests were conducted with commercial diesel fuel and also with other fuels, such as heavy oils. It could be shown that the C/S-procedure yields the same results as the gravimetric procedure independent of engine, engine mode and kind of fuel. The analysis of all important particulate compounds - elemental carbon ...
To evaluate the current situation and implementation of embolization of uterine leiomyomas into the treatment concept in women with symptomatic uterine leiomyomas in Germany. A questionnaire addressing the clinical background of uterine myomas, recommended treatment concepts, preclinical evaluation, technical approach and complications was sent to 164 departments of gynecology and radiology in Germany. 33 radiological departments and 19 gynecological departments submitted a completed questionnaire. Only 7 departments of radiology reported to have own experience with embolization of uterine leiomyomas, while only 2 departments of gynecology considered embolization as an alternative treatment option in patients with symptomatic leiomyomas. 18/33 radiological departments offer this treatment option but get no patient referrals. Agreement was found concerning the indications for treatment, preclinical evaluation by ultrasound and MRI, preferable location of treatable fibroids, technical ...
The RCP method was designed as a residue-optimised alternative to the thermally optimised grate firing of residual wastes. Its technical realisation and development to market maturity took no more than 5 years. In the first process stage the waste is converted to high-carbon pyrolysis charcoal and high-rank gas in the absence of oxygen. In the second stage these substances are oxidised by addition of oxygen. The resulting temperature causes the non-combustible constituents of the slag to melt. In a third, optional, stage this molten slag can be liberated of (heavy) metals to such an extent that it can subsequently be used directly as additive for grinding. Further exhaust gas treatment is facilitated by the use of a circulatory fluidised-bed secondary combustion chamber. Despite the reduced flue gas volume and resultant higher pollutant concentrations in the crude gas, overall emissions are lower than in conventional plants. [Deutsch] Das reststoffoptimierte RCP Verfahren ist als ...
Blades of modern steam turbines are designed for high efficiency and operational safety. Modern computer programs enable optimisation of design but factors like manufacturing, assembly, operation and downtimes still play an important role. Damage statistics show that blade damage still quite frequent. Selected cases from the Allianz damage assessment centre show some of the more frequent damage mechanisms. Damage is often caused when several factors come together. Prevention of follow-up damage requires early identification of beginning damage.(orig.) [German] Die Auslegung der Beschaufelung moderner Dampfturbinen hat die Vorgabe, einen hohen Wirkungsgrad bei gleichzeitig hoher Betriebssicherheit zu erreichen. Mit den heute zur Verfuegung stehenden Rechenprogrammen ist eine entsprechende Optimierung realisierbar. Fuer die langzeitige Betriebsbewaehrung haben aber Einflussgroessen aus Fertigung, Montage, Betrieb und Stillstand auch heute noch ...
The presented paper describes the formulation of the fractional mass balances which are used to calculate the concentration and size distribution of char in the balance cells of a circulating fluidized bed boiler. In case of using the shrinking core model additionally the distribution of conversion of the char particles is calculated. Basically two reaction models (a shrinking particle and a shrinking core model) are available to describe the combustion process. The model considers all essential physico/chemical phenomena (primary fragmentation, attrition, mass transfer to gas phase) which have to be taken into account for the description of the combustion process. The model is part of an overall simulation program for circulating fluidized bed boilers. This engineering simulator has been developed to return the main performance parameters of such systems like temperature along the furnace height, size distribution of balanced solid components, heat flows at the different heat ...
Experts tend to disagree about the economic effects of air pollution abatement measures. This book, which addresses also non-experts, explains the analytical background on the basis of available data. The authors conclude that there is a wide range of political options for achieving the goal of air pollution abatement. They differentiate between the various levels of discussion and show how misinterpretations of scientific results come about, thus making an important contribution to a discussion that is based on facts rather than emotions. [German] Die Einschaetzungen zur wirtschaftlichen Bewertung von Klimaschutzmassnahmen, insbesondere zur Steigerung der Energieeffizienz, sind sehr widerspruechlich. Dieses Buch erlaeutert anhand von Zahlenmaterial die analytischen Hintergruende und ist auch fuer Nicht-Oekonomen verstaendlich geschrieben. Die Autoren kommen zu dem Schluss, dass in vielen Bereichen rentable Energiesparpotentiale nicht erkannt ...
Investigations show that nickel-based alloys (MAR M 247 CC, CM DS 247 L and CMSX-4) can be successfully brazened. Tensile tests of MAR M 247 CC samples brazened with foil brazing showed values comparable to those of the base material, some samples failed because of base material problems. Tests with powder mixes made up from commercial brazens and the base material CMSX-4 showed good wetting and a perfect microstructure similar to the base material. Tensile test values at RT (test temperature) and 850 degrees centigrade show pronounced scatter. Tensile tests at RT and 850 degrees centigrade are used to optimse brazing cycles for the types of brazen used (temperature, time). (orig.) [German] Die Untersuchungen haben gezeigt, dass es moeglich ist, Nickelbasislegierungen (MAR M 247 CC, CM DS 247 LC und CMSX-4) erfolgreich zu loeten. Die im Zugversuch erhaltenen Festigkeitswerte der mit folienfoermigen Lot geloeteten MAR M 247 CC Proben erreichten Werte nahe der Festigkeit des ...
Recurrent variceal bleeding due to liver cirrhosis led to treatment with a transjugular intrahepatic portosystemic shunt (TIPS) in a pregnant woman at 20 weeks` gestation. Fetal radiation exposure was estimated to be less than 10 mSv. The use of a graduated catheter allowed measurement of field size and reliable determination of the patient`s entrance dose. Radiation exposure of an approximated fetal dosage of 5.2 mSv did not justify abortion for medical reasons. Therefore, TIPS procedure is not generally contraindicated during pregnancy itself. TIPS placement may be a therapeutic option related to the severity of the underlying maternal disease, after radiation exposure of the fetus has been estimated. (orig.) [Deutsch] Bei rezidivierender Oesophagusvarizenblutung auf dem Boden einer Leberzirrhose wurde bei bestehender Schwangerschaft der 20. Woche ein transjugulaerer portosystemischer Stent-Shunt (TIPS) neu angelegt. Praeinterventionell wurde ...
In an extended case report, we discuss four cases with masses in the lacrimal fossa representing the most important entities in this region (lymphoma, pleomorphadenoma, inflammatory pseudotumor, and malignant epithelial tumor). The different indications for CT and MRI are explained. For the differential diagnosis of lacrimal gland lesions, the following imaging parameters are important: The shape of the lacrimal gland, the inner structure, the degree of contrast enhancement, and the surrounding bony structures. In the evaluation of the expansion of lacrimal gland lesions, CT in thin slices with multiplanar reconstructions is equal to MRI. However, the contrast-enhancement of lacrimal glands is better evaluated with MRI than with CT. The bony structures are better visualized on CT than on MRI. (orig.) [Deutsch] In einem erweiterten Fallbericht wird ueber die vier grossen Entitaeten bei Traenendruesenraumforderungen berichtet (Lymphom, pleomorphes Adenom, ...
The low budgets of local governments and Federal States in Germany as well as lack of financial means of renters delaying thorough modernisation of existing heating systems in residential and public buildings, novel heat supply and related customer services are emerging on the market. Heat supply companies and housing construction associations increasingly use modern electronics and telecommunication systems for heating system upgrading and reliable operation and maintenance. This option holds an enormous potential of saving money today and in the future. Installation of remote control and maintenance systems and the related telephone-based services offer fast repair and other services via electronic telecommunications systems, thus saving money and manpower for the repair services of heat suppliers or plumbers, or financial losses due to rents being docked for broken down heating systems. Such remote control and maintenance systems however need to be reasonable in price, and versatile ...
The precipitation of heavy metals as hydroxides is the standard technique for the decontamination of waste water streams polluted by these elements. On the other side, progress in research has been made concerning the biosorption onto dead biomass and bioprecipitation supported by physiologically active bacteria. As the aim of this study, a flexible strategy has been envisaged cleaning a waste water with definite heavy metal load underlying the process mentioned above. Suitable bacteria were enriched and the process was tested in a technical plant. As result, a very high efficiency of heavy metal elimination has been found. The field of application covered by the acquired process is identical with the whole range of the waste water streams polluted by heavy metals. In addition, a second stage may be necessary if there are any further contaminants to be removed. (orig.) [Deutsch] Bei der Reinigung von schwermetallhaltigen Abwaessern ist der derzeitige Stand der ...
Pyrolysis and combustion of CH are investigated. In order to reduce the work required for the present combination of parameters, the following substances were selected: Hexachloroethane, hexachlorocyclohexane, hexachlorobenzene and hexachlorophene. The model substances were pyrolyzed or combusted in varying conditions, and the combustion or pyrolysis products were analyzed. Only the main products were of interest; trace components are important only as far as they may throw light on the reaction mechanisms. The furnace design resulted in incomplete combustion and pyrolysis reactions, so that products of all stages of combusition or pyrolysis were available for analysis. Reaction processes can be derived from the products. As an alternative to thermal treatment of refuse, biological degradation of chlorinated hydrocarbons was gone into. The efficiency of decomposition by microorganisms was to be compared with the efficiency of thermal destruction of chlorohydrocarbons. The ...
T{sub 2} weighted ultra-short turbo spin echo sequences were used in five individuals with variations in echo times, delayed triggering and echo intervals. To reduce movement artifacts all examinations were carried out with ECG and respiratory triggering. The sequences giving optimal image quality were then employed in 19 patients having various pulmonary abnormalities. Image resolutions, artifacts, image contrasts and diagnostic value were then judged by two observers and compared with CT. In the first study, a diastole-triggered UTSE sequence with the shortest echo proved optimal (T{sub E}=90 ms, T{sub R}=2-4 s, echo=9 ms, turbo factor=19). In the patient series studied, MRT was inferior to CT with regard to resolution and number of artifacts, but better in respect of contrast and diagnostic value. Using UTSE of the lung, MRT can produce images of good quality. Compared with CT, contrast is better with MRT, offering diagnostic advantages for MRT. (orig./MG) [Deutsch] Zuerst wurde an ...
The nuclear structure of A {proportional_to} 100 nuclei has been studied in the frame of this thesis with a recently developed {beta} - {gamma} - {gamma} triple coincidence fast timing technique and different models such as shell model, hydrodynamic model, Nilsson and particle-rotor models. This technique which allows the measurement of the level lifetimes in the ps range has been applied at JOSEF at the research reactor DIDO of KFA Juelich in studes of the short-lived neutron-rich nuclei in the A {approx_equal} 100 region. Lifetimes of level in {sup 96},{sup 98},{sup 100} ZR, {sup 99},{sup 101}-{sup 104} Nb, {sup 100}-{sup 105} Mo have been measured, which are in many cases completely new, and otherwise more precise than previously published data. From the lifetimes of the members of rotational bands, the size of the nuclear deformations has been deduced. (orig./HSI). [Deutsch] Im Rahmen dieser Doktorarbeit wurde die Kernstruktur der A {proportional_to} 100 Kerne untersucht. Dazu ...
Background. In multiple myeloma 5 different infiltration patterns can be differentiated: 1. Normal appearance of bone marrow, 2. focal involvement, 3. homogeneous diffuse infiltration, 4. combined diffuse and focal infiltration, 5. 'salt-and pepper' pattern with inhomogeneous bone marrow with interposition of fat islands. Methods. For the fast and total acquisition of all patterns a combination of a T1-weighted spin echo sequence and a fat suppression technique is superior. The focal involvement is clearly demonstrated as areas of high signal intensity on e.g. STIR images. Diffuse involvement can be quantified objectively by calculation of the percentage of signal intensity increase after contrast material injection. MRI is superior to X-ray in focal and diffuse involvement. With ultrafast sequences a 'screening' of the whole red bone marrow as for myeloma infiltration is possible. Prognosis. In prognosis studies diffuse infiltration is inferior to ...
Purpose: The determination of tumor volume in ocular tumors is very important for the planning and success of radiation therapy. This study uses an animal model to evaluate the accuracy of MR-based volumetry of ocular tumors. Materials and methods: In a total of 25 porcine eyes obtained from the slaughterhouse, ocular tumors were produced by injecting a mixture of hand creme and Gd-DTPA under ophthalmoscopic guidance. The injected volume varied between 0.05 ml and 2.7 ml. The eyes were examined with a 1.5 Tesla scanner and a 4 cm circular surface coil especially developed for ocular MRI. After data transfer to a separate workstation, volumetric analysis was carried out by three independent radiologists using semiautomated software. The determined volume was compared with the injected volume. Results: Of the 25 prepared porcine eyes, 23 were suitable for volumetric analysis. The injection of the mixture of hand creme and GD-DTPA produced two different types of tumors. ...
Aim: Treatment of carcinoma of the uterine cervix by remote afterloading brachytherapy has been accompanied with new isotopes having dose rates different from the classical low-dose rate (LDR) radium source. The dose rate conversion factor from LDR to high-dose rate (HDR) found to be around 0.54 in most studies. As regards medium-dose rate (MDR) brachytherapie, the published data are very few and the experience is still short. In this study the experience of Osaka University Hospital with micro-HDR-Selectron and Selectron-MDR, as a preliminary report of the clinical trial, is presented. Results: The 3-year survival and loco-regional control rates for both modalities were nearly equivalent (62% and 67% for HDR and 68% and 74% for MDR)(totally 45 patients). The cumulative rectal and bladder complication rates were the same in both groups (29% at 3 years), with only 1 patient (MDR-group) developed grade 3 rectal and bladder complication. In this study, point A dose rate correction factor ...
Purpose: In the present study the reduction of artifacts using an extended CT scale technique was examined in 5 vitallium and 5 titanium-aluminium-vanadium tumor prostheses. Methods: 5 titanium-aluminium-vanadium and 5 vitallium distal femur Mutars {sup trademark} tumor prostheses (Mutars {sup trademark} - Modular Universal Tumor And Revision System) were implanted in 10 human femur specimens. 110 artifical drill hole lesions of 1 mm, 2 mm, 3 mm, 5 mm and 8 mm diameter were placed in the bone around the hexagonal stem of the tumor prosthesis and furthermore in the proximal part of the femur. All specimens were examined using conventional CT and an extended CT scale technique in a slice thickness of 3 mm. Results: In the proximal part of the femur all drill holes could be detected using 3 mm slices, no artefacts were observed. Along the hexagonal stem smooth lines arising from each hexagonal plane could be observed. This made it impossible to detect a 1 mm drill in 1 vitallium and in 1 ...
Sprengel deformity is a congential malformation with usually unilateral elevation and medial rotation of the scapula. An omovertebral bone is generally present. Associated skeletal malformations are frequently present. Though functional impairment is mild, the cosmetic and psycho-social impairment can be considerable. The prognosis of early surgical therapy is good. The presented case also justifies surgical correction in the older child. (orig.) [German] Die Sprengel-Deformitaet ist eine angeborene Fehlbildung mit meist einseitiger Elevation und Medialrotation der Skapula. Meist ist ein Os omovertebrale vorhanden. Assoziierte skelettale Fehlbildungen sind haeufig. Obgleich funktionell wenig einschraenkend, ist die kosmetische und psycho-soziale Beeintraechtigung oft erheblich. Die Prognose der fruehen operativen Therapie ist gut. Der vorliegende Fall ermutigt zur operativen Therapie auch im hoeheren Kindesalter. (orig.)
Magnetic fields can be compensated by opposing fields. This principle can be applied for reducing the magnetic fields emanating from high-voltage transmission lines or found in residential or commercial buildings. The article shows a number of concrete options for reducing magnetic fields in the vicinity of high-voltage lines through appropriate conductor configuration on the one hand, and a novel method using Helmholtz coils for compensating those fields in buildings. (orig.) [Deutsch] Magnetische Felder koennen durch Gegenfelder kompensiert werden. Dieses Prinzip laesst sich sowohl auf Hochspannungsleitungen als auch auf Wohn- und Arbeitsraeume uebertragen. Der Artikel zeigt konkrete Moeglichkeiten, wie einerseits Magnetfelder von Hochspannungsleitungen durch eine geeignete Konfiguration der Leiter reduziert werden koennen, und beschreibt andererseits eine neue Methode zur Reduktion solcher Felder in Wohn- und Arbeitsraeumen mittels Helmholtz-Spulen. (orig.)
Efficiency of energy coversion of primary energy to an end use in industrial countries is about 30%. This is insufficient. Evaluating on basis of exergy efficiency becomes only about 15%. Usage of fuel cells give a great chance to improve efficiency. This concerns in particular to high temperature fuel cell systems SOFC and MCFC as well as their combination with heat pumps. [German] Die Effizienz der Energieversorgung in Industrielaendern ist energetisch bewertet mit rund 30 % unbefriedigend. Legt man den strengeren, energiewirtschaftlich treffenderen exergetischen Massstab an, halbiert sich dieser Wert sogar. Brennstoffzellen bieten durch ihren Einsatz Moeglichkeiten zur Effizienzerhoehung. Dies gilt insbesondere fuer die Hochtemperatursysteme SOFC und MCFC sowie deren Verbund mit Waermepumpen.
Rehabilitation of the abandoned uranium mining areas in Saxonia and Thuringia is a task posing also legal problems. The radiation protection laws of the former GDR continued to be effective to a great extent and proved to be a legal basis not ``perfect`` in formal terms, but suitably efficient in practice to tackle the manifold problems encountered in the land reclamation and waste disposal work. Originally intended to serve as a legal interim regime awaiting amendment at a later date, the body of laws available for the task proved to be a sufficient basis. (orig./HP) [Deutsch] Das fortgeltende Strahlenschutzrecht der frueheren DDR hat sich zwar nicht als formal `perfektes`, in der Sache aber strahlenschutzgerechtes und praktikables Instrument zur Loesung der anstehenden Sanierungsaufgaben erwiesen. Bei seiner Beurteilung darf nicht ausser Acht gelassen werden, dass die Ueberleitung dieses Rechts seinerzeit aus der Not eines kurzfristigen ...
The failure rate of dashpots has been determined on the basis of the results of annually recurring function tests on hydraulic dashpots, in order to determine the effects of longer test cycles on the safety of systems GKN I and GKN II. The use of a calculation method made it possible to establish the number of defective dashpots in the system as a whole. A subsequent investigation illustrated the way in which this figure changes when the test interval is increased from four to ten years, and the effects of this on system safety. (orig.) [Deutsch] Zur Ermittlung der Auswirkungen verlaengerter Pruefzyklen auf die Sicherheit der Anlagen GKN I und GKN II wurde, basierend auf Ergebnisse der jaehrlichen Funktionspruefung an hydraulischen Stossbremsen, die Fehlerrate der Stossbremsen bestimmt. Mit Hilfe eines Berechnungsverfahrens konnte die Anzahl maengelbehafteter Stossbremsen in der Gesamtanlage bestimmt werden. Eine anschliessende Untersuchung zeigte, wie sich dieser ...
Under the new name of ``geothermal heat pump``, ground-source heat pumps are currently high in demand in Northern America. In sectors characterized by heating and cold air demand, their advantages can be exploited to the full. For Germany, the end-use-energy substitution potential of geothermal heat pumps has been estimated at 1310-1470 PJ annually. Whether this potential can actually be exploited depends essentially on the development of energy prices, but also on the resourcefulness of plant and heat pump manufacturers in upgrading and cheapening geothermal heat pumps. (orig./RHM) [Deutsch] Unter der neuen Bezeichnung `Geothermal Heat Pump` erlebt die erdgekoppelte Waermepumpe z.Zt. in Nordamerika einen Verbreitungsschub. In dem durch Heiz- und Kuehlbedarf charakterisierten Umfeld kann sie Ihre Vorteile voll nutzen. Fuer Deutschland kommt eine Schaetzung zu einem Potential der erdgekoppelten Waermepumpen zur Substition von Endenergie von 1310-1470 PJ/a. Ob dieses ...
The pilot project of the conversion of the green forage drying plant Lengenfeld to biomass firing could not be realized without problems. But the experience until now shows that it is in principle possible. The farmers involved are devoted to the project. For them the cultivation of biomass is an alternative to the abandonment of fields. The present low oil price sets limits to the positive income effect. The aim is an increase of the biomass share in heating energy supply to about 80%. (orig.) [Deutsch] Die Umstellung der Gruenfuttertrocknung Lengenfeld auf Biomassefeuerung ist als Pilotprojekt nicht ohne Probleme moeglich gewesen. Die bisherigen Erfahrungen zeigen jedoch die grundsaetzliche Praktikabilitaet. Die beteiligten Landwirte sind engagiert bei der Sache und schaetzen die Produktionsmoeglichkeit als Alternative zur Flaechenstillegung. Der derzeit niedrige Oelpreis setzt der positiven Einkommenswirkung jedoch enge Grenzen. Eine ...
Modernisation of older office buildings commonly includes installation of air conditioning systems as good air quality and thermal comfort will improve the staff`s efficiency at work. However, what about tenants who want their own, individually controlled single-storey air conditioning plang? And what about retrofitting further storeys with single-storey air conditioning? An exemplary solution to this problem was found in Hamburg. (orig.) [Deutsch] Bei der Sanierung aelterer Buero- und Geschaeftshaeuser werden die Raeume immer haeufiger mit Klimaanlagen ausgestattet. Ein Grund fuer den Trend zur Klimatisierung: Gute Luftqualitaet und angenehme Temperaturen erhoehen die Leistungsfaehigkeit des Menschen. Was aber, wenn ein Mieter fuer seine Bueroetage eine eigene, individuell steuerbare Klimaanlage wuenscht? Und was passiert, wenn andere Bueroetagen mit weiteren Klimaanlagen nachgeruestet werden? In Hamburg wurde dieses Problem auf beispielhafte ...
The European Court of Justice has defined a clear means by which waste utilisation methods can be distinguished from waste disposal methods in a logical, well-understandable manner. With its stringent definition of ''utilisation'' this judgement points the way to quality-oriented waste management practices. We do not share the often voiced fear that this decision will lead to an increased incineration of compound wastes in industrial plants such as cement works. From the fact that, according to the decision by the European Court of Justice, wastes destined for utilisation fulfil a certain purpose and therefore, if not available in sufficient quantity must be replaced by primary raw materials, it follows that these wastes are required to fulfil specific quality criteria. This is rarely the case, if at all, with compound wastes. From the viewpoint of Luxembourg the decision by the European Court of Justice can be regarded as a positive impulse towards ...
DMT has developed what is called the stepped reforming process. This is an allothermal gasification process which uses hydrogen for a gasification medium. First the biomass is pyrolised by means of a heat transfer material. The escaping gaseous and condensable constituents are hydrogenated, heated in a reforming stage and are made to react to a hydrogen-rich product gas by means of homogeneous gasification. The heat required for this is provided by burning the pyrolysis coke. This makes it possible to dispense with process stages that would involve gasification of solid material and hence require higher pressure levels. The present process also works at ambient pressure. Moreover, stepped reforming promises a number of additional advantages: low-tar product gas containing 60% hydrogen, high cold gas efficiency, no wastewater arisings, robust operating behaviour. This paper outlines the basic ideas that led to the development of stepped reforming process and describes its diverse ...
During their life, intervertebral discs undergo degenerative changes which need not necessarily become lesions. Conventional X-rays do not provide information on the condition of the intervertebral discs, so MRT or CT are recommended as primary techniques as they are non-invasive. Invasive methods like myelography and especially discography should not be used unless a case is highly problematic. In infants with pains in the back, MRT should be carried out as early as possible as there is nearly always an organic cause. (orig.) [German] Die Bandscheibe ist im Laufe des Lebens degenerativen Veraenderungen unterworfen, die klinisch zu Beschwerden fuehren koennen, aber nicht fuehren muessen. Konventionlle Roentgenaufnahmen lassen zwar die Hoehenminderung des Bandscheibenfachs und begleitende knoecherne Veraenderungen erkennen, nicht aber den Zustand der Bandscheibe selbst. Die Beurteilung der Bandscheibe und des Knochens gelingt mit der CT, die parallel zum Bandscheibenfach durchgefuehrt ...
A procedure is described for the isolation and determination of {sup 90}Sr, {sup 226}Ra, {sup 228}Ra and {sup 210}Pb in food. These nuclides are highly radiotoxic, above all for babies and children. Samples are dry ashed, alkali metals are removed as carbonates. Separation from other matrix ions and separation of Ra, Sr and Pb can be achieved with a column of Sr-Spec, an immobilized crown ether. For activity measurements membrane filters with SrSO{sub 4}, Ba(Ra)SO{sub 4} and PbS are prepared. Ra is determined by gamma-spectrometry, {sup 90}Sr and {sup 210}Pb are determined by low-level-betacounting. The determination limits are 10 mBq/kg for {sup 90}Sr and {sup 210}Pb and 50 mBq/kg for {sup 226}Ra and {sup 228}Ra. The procedure is useful for all kinds of foodstuff. (orig.) [Deutsch] Es wird ein Analysengang zur Abtrennung und Bestimmung von {sup 90}Sr, {sup 226}Ra, {sup 228}Ra und {sup 210}Pb in Lebensmitteln beschrieben. Ein Merkmal dieser Nuklide ist ihre hohe ...
Surface structure analysis, i.e. metallographic analysis of component surfaces with the aid of replicas, is an established method of component monitoring and the only reliable non-destructive method for detecting and analyzing beginning creep damage in the form of creep pores. Creep pore development provides a basis for component condition analysis. It must be noted, however, that the modern martensitic 9-12 % Cr steels - like the established steels 10CrMo9-10 (P22) und X20CrMoV12-1 - have comparatively high creep fracture deformation rates in fatigue tests. This raises the question if these steels can be judged on the basis of data for established steels. The results so far suggest that even with low pore densities (single pores), a higher degree of damage and a shorter time until failure must be assumed. [German] Eine bewaehrte Methode der Bauteilueberwachung stellt die Oberflaechengefuegeuntersuchung, d. h. die metallografische Untersuchung der Bauteiloberflaeche mit Hilfe von ...
TRITEX was a pumped loop with Pb-15.8Li, fabricated from steel 1.4922. In contact with the molten eutectic were also molybdenum, vanadium and armco-iron. The loop was originally designed to investigate tritium extraction using solid getter metals. Over the years the goal changed to the study of metals, corrosion products and purification of the eutectic mixture. Therefore many modifications were done. The first part of this report describes TRITEX. All parts were enclosed in thermoboxes for a homogeneous temperature. One test section was in an argon glove box and could be opened during operation. Other special equipment`s were: permeation membranes and liquid-metal-covergas-interfaces to study the transport of H{sub 2}, D{sub 2} and {sup 3}H, different purification devices, a quartz observation window to see the liquid metal surface, 4 different kinds of flow measurements, level indicators, freeze valves. The second part describes loop operation. Between 1989 and 1996, the eutectic ...
The first volume of the report covers the state of implementation of primary and secondary measures for SO{sub 2}- and NO{sub x} control applied in the most important industrial sectors in Germany. Integrated pollution abatement techniques, called primary measures in this report, such as process integrated measures and low emission processes, have gained increased importance in recent years. The end-of-pipe processes, described here as secondary measures, are generally highly effective. They represent mature technologies, which are capable of achieving significant reductions in SO{sub 2}- and NO{sub x} emissions, and which have been used in particular for retrofitting existing plants. At first, an overview is given regarding the development of SO{sub 2}- and NO{sub x} emissions in selected European countries during the last 20 years and in Europe. Current national and European emission limits and emission guidelines on SO{sub 2}- and NO{sub x} emissions from stationary sources are ...
Objective: To evaluate the treatment of malignant biliary stenoses and occlusions using a new stent. Methods: In a prospective study, 25 patients with malignant obstructive jaundice were treated with SMART stents. The handling and the quality of stent expansion were documented. Stent function was assessed 2-4 days after intervention by cholangiography and laboratory tests. A follow-up was performed three months, after stent placement. Results: All lesions were treated successfully, with a total of 35 stents implanted. In 14 patients a further balloon dilatation was performed after stent placement (8-10 mm diameter/40-80 mm length). The mean serum bilirubin level decreased significantly from 11.6 mg/dl to 4.6 mg/dl after intervention (p<0.05). The follow-up showed a mean serum bilirubin level at 4.0 mg/dl. In 4 cases (16%) a further intervention (PTCD or stent) was performed. Six patients died due to tumor progression. The stents proved to be patent in 79% (n=15) of patients ...
Damage survey of protective coats of modern gas turbine blade shows that most damages are not due to classic wear mechanisms such as oxydation or high-temperature corrosion but caused by foreign bodies, poor coating during manufacturing, or operation-caused cracks. Mere visual inspection of cracks is often not sufficient to tell whether cracks are superficial or whether they have already progressed into the base material. Non-destructive methods such as ultrasonic inspection or eddy-current testing are helpful tools but there is not yet a fully matured testing concept at hand. Metallographical tests can give important information about crack mechanisms and thermal, chemical and mechanical stresses.(orig.) [German] Die Schadenerfahrung mit Schutzschichten moderner Gasturbinenschaufeln zeigt, dass die meisten Schaeden nicht auf die klassischen Verbrauchsmechanismen wie Oxydation und Hochtemperaturkorrosion zurueckzufuehren sind, sondern durch Fremdkoerper, herstellungsbedingte ...
This 7th edition reveals the progress in steam engineering and the great future potential of steam engineering applications. Pollution abatement and design experiences gained during the operation of existing plants, and experiences gained in waste incineration are of environmental relevance. Recent materials developments and knowledge, e.g. as regards pipes and fittings, have been making significant contributions to supercritical-steam efficiency improvements. Emphasis is also placed on automation, control engineering, water chemistry etc., and on regulations, licensing procedures, and the training of the staff of plants. (orig./KOW) [Deutsch] Die nunmehr vorliegende 7. Ausgabe zeigt den Fortschritt und das zukuenftig noch erhebliche Potential dieser Technik auf. Erfahrungen mit den nun schon seit Jahren laufenden Anlagen zur Schadstoffminderung, Konstruktion und Auslegung sowie Betriebserfahrungen zur thermischen Abfallverwertung sind ...
For location of leakage at district heating pipelines several techniques are available today. If there is no wire bound lead monitoring system installed, the DH company has to apply mobile methods for detection and location and if possible characterization of leakage. Most mobile methods available today are restricted in application and often they cause supply disconnections, especially the location of very small leaks is difficult. The Institute for Environmental, Safety and Energy Technology (UMSICHT) has tested a new developed method that can be executed by own employees of DH companies that can be realised parallel to normal supply mode, and that is able to locate and characterize even very small leakages. (orig.) [Deutsch] Zur Lecksuche an Fernwaermeleitungen stehen verschiedene Techniken zur Verfuegung. Wurde beim Bau der Fernwaermetrasse kein drahtgebundenes Ueberwachungssystem eingebaut, ist der Netzbetreiber auf mobile Lecksuchmethoden ...
As an alternative to surgery, endovascular therapy with stent grafts has become the second main treatment option for infrarenal abdominal aortic aneurysms. Unlike surgery, endovascular treatment with stent grafts is also applicable in patients unfit for open repair. Despite current improvements in endovascular repair devices, significant anatomic barriers still exclude this technique for a large number of patients. Computed tomography, magnetic resonance imaging, and ultrasound are essential for diagnostics, preintervention planning, and postintervention follow-up of abdominal aneurysms treated with stent grafts. This review covers etiology, pathology, and diagnostic aspects. Materials and methods for endovascular treatment of abdominal aortic aneurysms are presented in detail, and clinical results and complications are discussed. (orig.) [German] Die endovaskulaere Therapie des infrarenalen Bauchaortenaneurysmas hat sich als Alternative zur offenen chirurgischen ...
With publication the fire design rules of the Eurocode and the national application documents (NAD) for the first time also calculation methods of constructive structural fire protection are available. This dimensioning of components and structures in fire case is based on the normal temperature design on Eurocodes and can be applied in the future as alternative to the classical fire design method of the German standard DIN 4102 part 4. In this contribution a view of the proof procedures of the Eurocode fire protection parts and the arrangements of the NADs is given as soon as the application of these fire design rules in Germany is described. (orig.) [German] Mit der Veroeffentlichung der Eurocode-Brandschutzteile als Vornormen und der zugehoerigen nationalen Anwendungsregelungen (NAD) als DIN-Fachberichte stehen erstmals auch rechnerische Nachweisverfahren fuer den konstruktiven baulichen Brandschutz zur Verfuegung. Diese brandschutztechnische Bemessung von ...
When performing trenchless pipe renovation work - whichever process you use - the success of the job depends on the careful removal of all scale, sediments and rust from the innerwall surfaces. The VACUJET process - in which the pipe is cleaned with water at pressures of up to 2 500 bar using a technique jointly developed by Preussag Rohrsanierung GmbH and Fabex GmbH - meets all requirements. The equipment includes a mobile waste water treatment unit which is small enough to fit on a standard trailer. Despite its compact dimensions this plant is so effective that it can treat all the waste water generated during the high pressure cleaning jobs so that it is suitable for reuse in the cleaning process or for release into the sewerage system. (orig.) [Deutsch] Bei der grabenlosen Rohrsanierung, ganz gleich nach welchem Verfahren saniert wird, ist die sorgfaeltige Entfernung von alten Beschichtungen, Ablagerungen und Rost eine wesentliche Voraussetzung fuer den ...
As one of the largest contractors for the construction of ethylene plants featuring steam cracker furnaces as their core component Linde AG has examined the `real` chemical recycling of polymers in steam cracker furnaces as an alternative to their thermal utilisation. In steam cracker furnaces the feedstock, i.e., hydrocarbons, is broken down to ethylene, propylene, and other valuable products in a steam dilution of approx. 800-870 C. In the ideal case, if polyolefins are used as feedstock, then the initial product which led to the polymers can be fully recycled. In this context a series of experiments was carried out in a laboratory-scale cracker plant. The purpose of this was to demonstrate the technical feasibility and the economic advantage of using recycling polyethylene or polypropylene as feedstock for steam cracker plants. (orig./SR) [Deutsch] Die Linde AG als einer der bedeutendsten Kontraktoren fuer den Bau von Ethylenanlagen, deren Herzstueck die Steamcrackeroefen sind, hat ...
The typical MRI features of the most common pancreatic diseases, such as pancreatitis and adenocarcinoma of the pancreas, have been established. However, even in these common pancreatic disorders, MRI correlation with the underlying pathology is limited for clinical reasons. We emphasize MR-pathological correlation of inflammatory and neoplastic pancreatic changes, including pancreatitis, adenocarcinoma, acinar cell carcinoma, rare cystic and solid pancreatic neoplasms, and islet cell tumors. By highlighting the correlation of key pathological features with MR findings, a better understanding of the MR appearance of pancreatic pathology can be provided. In addition, MRI may prove a powerful tool in detection and characterization of pancreatic tumors. (orig.) [Deutsch] Das MR-tomographische Erscheinungsbild von Pankreatitiden und Adenokarzinomen des Pankreas, als den haeufigsten Pankreaserkrankungen, ist zwar ausreichend bekannt; allerdings ist selbst bei diesen ...
Steam turbines of the new power plant generation enable the realisation of over-critical steam parameters with 600 C and 300 bar by means of simple and double resuperheating. Extensive research work in the field of material technology has provided the pre-conditions. Forged pieces, castings, high-temperature ferritic 9 - 10 % CrMoV steels, which are additionally alloyed with niobium, nitrogen and wolfram, are used in steam turbines. A proof of strength for shaft and cast steels is available by means of a long-term stress-rupture test of up to max. 60,000 hours. The strength of turbine steels exceeds the one in tube and header steels (x 10 CrMoVNbN 9 1). (orig./MM) [Deutsch] Dampfturbinen der neuen Kraftwerksgeneration erlauben heute die Realisierung von ueberkritischen Dampfparametern mit 600 C und 300 bar mit einfacher und zweifacher Zwischenueberhitzung. Umfangreiche werkstofftechnische Forschungsarbeiten haben dafuer die Voraussetzung geschaffen. Zur Anwendung ...
Metal hydrode stores are used as fuel tanks in vehicles or as stationary stores of high-purity hydrogen. Equilibrium isotherms at low pessures were measured in order to validate the laws of Henry or Sievert for hydrogen uptake of the alloy Ti{sub 0.98}Zr{sub 0.02}V{sub 0.43}Fe{sub 0.09}Cr{sub 0.05}Mn{sub 1.5} (patented by Daimler Benz AG, code DB5800). The laws were to provide information on whether hydrogen uptake is atomic or molecular and on the conditions in which isothermal measurements are possible. (orig.) [Deutsch] Metallhydridspeicher werden als Kraftstofftank in Fahrzeuge oder als stationaere Speicher zur Bereitstellung von Reinstwasserstoff verwendet. Fuer diese Arbeit wurden die Gleichgewichtsisothermen bei kleinen Druecken vermessen, um die Gesetze von HENRY oder SIEVERT fuer die Wasserstoffaufnahme in der Legierung Ti{sub 0.98}Zr{sub 0.02}V{sub 0.43}Fe{sub 0.09}Cr{sub 0.05}Mn{sub 1.5} zu pruefen. Anhand dieser Gesetze ist zu ...
The article deals with the problem of a humidity addition to thermal conductivity, diffusion and latent heat effects in heat transfer through building components. It shows with examples humidity effects for exterior walls with core insulation, with composite insulation system as well as for insulated roof membrane assemblies. From these it can be summarized that - sorption humidity is for today`s construction conditions (good thermal insulation and humidity protection) a suitable reference quantity for the determination of practice-oriented, substance-specific and physically correct humidity additions to the thermal conductivity of hygroscopic components; - diffusion and latent heat effects are in case of good rain imperviousness and low water absorbing capacity of the exterior component layers of secondary importance for transmission heat losses; - an increase in insulating layer thickness in order to improve the thermal insulation is possible without humidity problems; - today`s ...
The required introduction of on board diagnosis II in the USA from the 94 models onward has led vehicle manufacturers and system suppliers to develop corresponding diagnosis processes at the beginning of the 1990`s. These systems are now in mass production for TLEV and partly for LEV requirements. Based on experience from the wide use of these functions, new knowledge has been obtained, which must be taken into account in the development of future systems. The additionally more severe emission and diagnosis requirements make further minimisation of the overall tolerances on the one hand, and a revision of the existing diagnosis algorithms necessary. In parallel with this, the Law must create the necessary outline conditions, where the requirements for the vehicle manufacturer and system suppliers must also be met. The OBD II development must therefore certainly not be regarded as complete. [Deutsch] Die in den USA ab Modelljahr `94 geforderte Einfuehrung der On Board Diagnose II hat zu ...
The intermetallic phase NiAl is a potential material for high-temperature applications; however, its technical application was prevented so far by its high brittleness at room temperature. This problem may be solved by incorporating relatively high-ductility particles into the NiAl matrix. Controlled crack propagation experiments, tensile and pressure tests were carried out in order to analyze the toughness and deformation characteristics of NiAl composite materials containing niobium or molybdenum particles at room temperature and in ambient atmosphere. Both the niobium and the molybdenum particles increase the toughness as compared to the pure NiAl matrix, but no ductilisation was observed in the composite materials investigated. Model experiments in consideration of experimental data suggest, hovewer, that the toughness and ductility of NiAl may be enhanced by optimizing the microstructural and production parameters of the incorporated ductile particles. (orig.) [Deutsch] Die ...
Purpose: To assess the new method of 3-dimensional echocardiography in comparison to the 'gold standard' MRI as to its ability to calculate left ventricular volumes in patients with congenital heart disease. Materials and methods: Eighteen patients between the ages of 3.9 to 37.3 years (mean: 12.8{+-}9.7) with a geometrically abnormal left ventricle were examined using a 1.5 T scanner with a fast gradient-echo sequence (TR=14 ms, TE=2.6-2.9 ms, FOV=300-400 mm, flip angle=20 , matrix=128:256, slice thickness=5 mm, retrospective gating) in multislice-multiphase technique. Transthoracic 3D-echocardiography was performed with a 3.5 MHz transducer and a Tomtec {sup trademark} (Munich, Germany) system for 3D reconstruction. Results: Volume calculation was possible in all patients with 3D-echocardiography, but the muscle mass calculation only succeeded in 11 to 18 patients (61%) due to inadequate visualization of the entire myocardium. Comparing MRI and 3D-echocardiography, ...
For purposes of assessing the dumpability of wastes, Article 1 - Ordinance on the Environmentally Responsible Landfilling of Household Wastes (AbfAblV) - of the Ordinance on the Environmentally Responsible Landfilling of Household Wastes and Biological Waste Treatment Plants defines classificaton criteria for biologically and mechanically treated wastes destined for landfilling. The practical experiences that have been gathered with these classification criteria and values were evaluated in a questionnaire-based survey. This was done in particular for the purpose of verifying and validating proposals on the methodology of respiration and fermentation tests. A general finding has been that the application and implementation of the regulations of the AbfAblV is fraught with difficulties. This is evident for one thing in the frequency of analyses and for another in the difficulty of complying with the limit values of the classification criteria. The authors are in support of demands that ...
1. Cyanide degradation: Of the cyanide- and thiocyanate-degrading bacteria, Burkholderia cepacia and Pseudomonas spec. were the most effective. 2. Biosorption: Of the isolates suited for biosorption of heavy metals, 597-A (non-identifiable) and 597-A2 (Aspergillus fumigatis) had the biggest potential. The sorption capacity of the fungi for metals varied with the C source used for their growth: apple juice > molasses > glucose. The fungi are not cyanide-sensitive and can even degrade cyanide. Living biomass had better metal sorption efficiencies than dead mycelium. The biosorption rates in waste water were usually higher than in broth. Depending on the metal composition and concentrations and on the exposure time and volume of the mycelia, up to 85 % of the initial concentration was removed from the liquid phase. The capacity of different biomasses for the sorption of metal mixtures was between 65 and 80 mg/g of dry matter depending on the experimental conditions, with ...
Minimally invasive thermotherapies for focal tissue destruction on the basis of laser-, microwave-, focused ultrasound-, or cryogeninduced changes of tissue temperature represent an alternative to surgical tissue ablation, particularly in the treatment of tumors. The thermotherapy modalities listed necessitate indirect guidance and monitoring, since they often do not lend themselves to immediate visual control. In the brain, in head and neck tumors, in the liver, and in the prostate, MRI reliably and accurately delineates both the positions of interstitial thermotherapy applicators and - in contrast-enhanced, T1-weighted images - the perfusion defects in tissue necrosis induced by thermotherapy. The transfer of results of in-vitro and in-vivo model studies to assess interstitial temperature and lesion development during thermotherapy to the actual treatment of patients, however, is still in an initial phase. Further development of both rapid MRI sequences and MRI scanners suited for ...
Volatile organic compounds (VOC) are an important group of pollutants with adverse effects on humans and the environment. Primary air pollution abatement measures aim at prevention or reduction of pollutant production in industrial production processes, e.g. by improved processes but also by other methods (closed cycle processes, different process materials, etc.). If these measures have been implemented and emissions are still too high, an off-air purification unit must be installed. Biological purification is the method of choice for low pollutant concentrations. Biological purification processes are based on the activity of microorganisms which are capable of biochemical oxidation of organic and some inorganic gaseous compounds into non-polluting or non-odorous compounds. These processes have the advantage that they work at ambient conditions and therefore remove relatively low pollutant concentrations at low investment and operating cost. Lately, biological filters and washers have ...
Normally, the alloy NiMo28 is used in the solution annealed and quenched condition in which it has a face centred cubic matrix structure. The matrix of the material is supersaturated with molybdenum and, at temperatures above 800 C, has a tendency to form intermetallic precipitates such as the Ni{sub 4}Mo-ordered phase leading to the embrittlement of the NiMo28-ordered phase leading to the embrittlement of the NiMo28 alloy during hot working. For this reason, the aim of these investigations was to optimise the alloy by reducing its tendency to embrittle. The TEM-analyses carried out served to investigate the precipitation of the material as a function of its iron content after ageing at 700 C. The change in hardness and in the lattice constants of the NiMo28-specimens with iron content were also determined. To improve the hot working properties of this material it is recommended that the iron content be kept to about 3.2 mass % in order to reduce the tendency of the alloy to ...
Purpose: In an experimental study, the correlation between the trabecular bone density of the different regions of the proximal femur and the fracture load in the setting of femoral neck fractures was examined. Methods: The bone mineral density 41 random proximal human femora was estimated by single-energy quanitative CT (SE-QCT). The trabecular bone density was measured at the greatest possible extracortical volume at midcapital, midneck and intertrochanteric level and in the 1 cm{sup 3} volumes of the centres of these regions in a standardised 10 mm thick slice in the middle of the femoral neck axis (in mg/ml Ca-hydroxyl apatite). The proximal femora were then isolated and mounted on a compression/bending device under two-legged stand conditions and loaded up to the point when a femoral neck fracture occurred. Results: Statistical analysis revealed a linear correlation between the trabecular bone density and the fracture load for the greater regions, with the highest value in the ...
Present day mammography has not been able to make use of the advantages of digital luminescence radiography because of the limited spatial resolution. The recent development of electromagnetic focusing X-ray tube with effective focal spot sizes from 0.04 to 0.12 mm allows radiographic direct magnification with less geometric blur. It is now possible to combine direct magnification mammography with digital luminescence radiography. By combining high quality storage phosphor screens with an HQ-workstation a spatial resolution of 8 lp/mm is possible for 1.7-fold magnification. For 4-fold spot magnification views spatial resolution can be theoretically increased to approx. 20 lp/mm. One important advantage of digital radiography is the possibility of image-postprocessing. This article presents two sets of standard parameters and three sets of image dependent parameters for better imaging of specific lesions, such as microcalcifications. The introduction of the storage phosphor screen ...
To permit an assessment of the system presented in this paper the data collected up to this point should be complemented by further experience with its practical use in electromobiles and the recovery of zink and the electrolyte. To this end the system is to be tested in electromobiles in 1995 and 1996. If there are no serious problems in the course of these tests and the above-mentioned estimates on economic efficiency are confirmed, then there is much to be said for a large-scale trial of these battery systems in electromobiles in the framework of a pilot project in Karlsruhe. Because of the infrastructure required for recharging, such a project should first be carried out in cooperation with fleet operators. As the recharging technique employed is so simple as to require no great investment and cost-effectiveness should already be achievable with a few tens of vehicles, one can conceive of a whole variety of applications in cooperation with public utilities, municipalities, and ...
1. In order to carry out isothermic crystal growth experiments of YBCO the 123 primary crystallization field was determined by means of phase diagram investigations and crystal growth experiments at different oxygen partial pressure. 2. YBCO single crystals of high crystallographic perfection were grown and conclusions on the flux pinning mechanism were drawn. 3. By means of Liquid Phase Epitaxy (LPE) single crystalline (Tc{approx}90 K; {Delta}T{<=}0.5 K) c- and a,b- YBCO fils have been prepared on NdGaO{sub 3} and LaGaO{sub 3} substrates. The films were characterized structurally and magnetically. 4. Our fist melt textured YBCO ``single crystals`` possess intracrystalline critical current densities >10{sup 4} A/cm{sup 2} at B{<=}2T. The irreversibility inductions are {<=}6 T at 77 K. A simple demonstrator was constructed together with the IFW Dresden and a growth model was developed. 5. Using above all torque magnetometer measurements we separated intrinsic pinning effects ...
Aim: Changes within the brain detected by MRI after chronic manganese poisoning raised the question whether morphological changes of the basal ganglia, particularly of the globus pallidus, could be detected after chronic occupational exposure to manganese dioxide. Results: No cases of parkinsonism were detected in clinical examinations or by other means. The mean manganese concentration in blood was 12 {mu}g/l (range: 3.9-23.3 {mu}g/l). In comparison to the upper reference value of 10 {mu}g/l, 42 workers (56%) had a higher body burden. A significant positive correlation between manganese levels in blood and the PI (indicated by T{sub 1}-shortening) was observed as well as between the CBI and workplace-specific exposure. Brain atrophy was not detected in any of the observed cases. Conclusions: Long-term exposure to manganese dioxide dust correlates with the Pallidum-Index in MRI scans. Although the MRI findings have no current clinical relevance for individuals, further studies are ...
Functional imaging of the pharynx used to be the domain of cineradiography, CT and ultrafast CT. The development of modern MRI techniques led to new access to functional disorders of the pharynx. The aim of this study was to implement a new MRI technique to examine oropharyngeal obstructive mechanisms in patients with obstructive sleep apnea (OSA). Sixteen patients suffering from OSA and 6 healthy volunteers were examined on a 1.5 T whole-body imager (`Vision`, Siemens, Erlangen Medical Engineering, Germany) using a circular polarized head coil. Imaging was performed with 2D flash sequences in midsagittal and axial planes. Patients and volunteers were asked to breathe normally through the nose and to simulate snoring and the Mueller maneuver during magnetic resonance imaging (MRI). Prior to MRI, all patients underwent an ear, nose and throat (ENT) examination, functional fiberoptic nasopharyngoscopy and polysomnography. A temporal resolution of 6 images/s and an in-plane resolution of ...
Purpose: For planning the therapeutic strategies and estimating the prognosis in esophageal cancer, N-staging is very important. To date, MRI still is of minor importance as imaging modality of the mediastinum despite promising developments in the past, like ECG-gating or 'averaging' sequences, e.g. LOTA (Long-term averaging), which facilitate mediastinal and thoracic MR-imaging. In a prospective approach, the value of MRI based N-staging was examined with respect to LOTA-sequences. Material and Methods: Within from weeks prior to esophagectomy, standardized MRI of the esophagus was performed in 15 patients (10 squamous-cell-carcinomas and 5 adenocarcinomas) using a 1.5 T whole body scanner. Imaging quality was classified based on depiction of aortic wall or tracheal wall layers. Criteria for malignant infiltration were a diameter of more than 15 mm or a round appearance of a lymph node together with GD-DTPA enhancement. All data were blinded and separately read by ...
Main topic of the project was the manufacturing of highly efficient GaAs-solar cells and the fabrication of concentrator cells. During this process significant progress was made with the material preparation, the solar cell technology and the material and process characterisation. This succeeded in the following efficiencies: - GaAs solar cell made by MOVPE technology: 22.9% on 4 cm{sup 2} (AM1.5g) - GaAs solar cell made by LPE-ER process: 22.8% on 4 cm{sup 2} (AM1.5g) - GaAs concentrator solar cell made by LPE-ER process: 24.9% at C=100xAM1.5d - GaAs concentrator module with fresnel lenses: Module efficiency 20.1% (under irradiation of 793 W/m{sup 2}). Another main focus was the epitaxy of GaAs on Si substrate. Two different approaches were investigated. Together with the cooperation partner ASE, Heilbronn a selective growth technology was developed that led to a decreased crack formation. By a simultanous optimization of the other epitaxy and process parameters, the efficiency was ...
The staging of patients with multiple myeloma demands sensitive imaging methods for the assessment of the skeletal system. MRI allows for direct visualization of the bone marrow which exhibits five different infiltration patterns in multiple myeloma: 1. normal appearance of the bone marrow, 2. focal involvement, 3. homogeneous diffuse infiltration, 4. combined diffuse and focal infiltration, 5. ''salt and pepper'' pattern with inhomogeneous bone marrow signals due to multiple fat islands. The combination of T1w-SE and STIR sequences is best suited for detecting all infiltration patterns and for the differential diagnoses e. g. hemangiomas. With parallel imaging in MRI, acquisition times can be markedly reduced and whole-body screening of the bone marrow can be achieved within 30 min. MRI is superior to radiography for the detection of focal as well as diffuse infiltration. Multidetector computed tomography and especially 16- and 64-detector row ...
Purpose: An animal model is used to investigate whether MR angiography combined with super-paramagnetic particles of iron oxide (SPIO) is suitable for detecting thromboses. Methods: 42 rats in groups of 7 each were examined on days 1, 3, 5, 7, 9 and 11, respectively, after mechanical/chemical thrombus induction in a 1.5 Tesla magnet with a FISP sequence (TR/TE/FA 50 ms/6 ms/40 ). Imaging was performed before and up to 90 minutes after intravenous injection of 30 {mu}mol FE/kg BW of the experimental SPIO (hydrodynamic diameter, 34{+-}17 nm LLS; R1 and R2 relaxivity at 0.47 T, 31 and 57 L/(mmol*s)). MIP reconstructions of MR angiographies were submitted to consensus assessment by two examiners using histology as the gold standard. Results: The image quality of MIP reconstructions was rated as good in 38 of 42 cases. With regard to thrombotic vessel occlusion, MR angiography coincided with histology in 17 of 42 cases and differed in 25, lumen narrowing being overestimated by MRI in 4 ...
Atomization of liquid fuel in aircraft engines requires application of airblast atomizers, where the kerosene is supplied into the shear layer between two swirling airstreams. The transfer of this functional principle towards gaseous fuel, as illustrated in Fig. 1, yielded a strong influence of the swirl arrangement of the airflows on flame stability and homogeneity of the fuel/air-mixture. Compared to the co-swirl configuration the flow field of the counter-swirl arrangement exhibits a marked increase of the mass flow recirculated in the internal recirculation zone and a reduction of its length in axial direction. This is attributed to the faster decay of tangential velocity maxima in case of counter-rotating airflows. This generates a stronger positive axial pressure gradient dp/dx, thus enhancing the internal recirculation zone. Analysis of local turbulence quantities yields a restriction of turbulent exchange to smaller radial sections and lower maximum values in the jet dominated ...
Against the background of more severe limitation of particle emission in all application areas of Diesel engines, it is necessary to monitor the particle emission, but also the chemical composition of the particles. The basis of assessing particle emission is formed by gravimetric determination of the particle concentration from exhaust gas diluted with particle-free ambient air, with a maximum temperature of 52 degrees C at the sampling position. While it is already possible, using the part flow dilution system, to take samples locally, previously the subsequent particle determination and characterisation could only be done in a chemical laboratory. For this reason, the C/S particle measurement process was developed as an alternative to gravimetry, which can be used locally, eg: on ships and which makes it possible to determine the particle mass and composition. This process is based on a thermographic carbon and sulphate determination. Comparative investigations were done both on ...
In technical combustors, flow and combustion processes inside the combustion chamber determine the design and also the safety of the plant. A modelling technique was developed at TU Dresden which comprises both numerical simulations and experimental data and thus achieves a high degree of transparency in its visualisation of the processes inside the combustion chambers under investigation. With the experience gained, numerical models of commercial simulation software (FLUENT, CFX) can be validated by measured values, and potential applications of the programs can be investigated. The first stage of experimental modelling consisted in isothermal (cold) modelling in consideration of flow-relevant similarity characteristics. In the reactive, non-isothermal models, the fuel/air ratio and temperature conditions inside the original combustion chamber were modelled as well. In order to obtain detailed data on the combustion conditions at the burner, measurements were made on a separate ...
This report completes the documentation for the research project 'High Pressure Compressor - Preliminary Design as Basis for the Development of an Efficient and Environmentally Friendly Core Engine' which was funded by the Ministry of Economics of State Brandenburg. The objective of the project is to deliver a preliminary compressor aerodynamic design as well as design studies for an efficient, weight and cost improved compressor. The increase of stage pressure ratio and improved efficiency, whilst stage and blade count is reduced, has been achieved by advanced 3D methods. Compressor stability also at off-design conditions will be retained. The mechanical design focusses on a cost and weight optimised rotor not only for a conventional bladed discs but also for Blish stages. Various options for split casings have been developed and assessed. Alternative vortex reducers based on different design options have been carried out. The results from this project will be ...
After 3 years of construction the trial run of the heating power station HKW 2 ended in November 1997 on time. No extraordinary damage occured during construction, assembly or commissioning. The plant has been operating according to schedule since November 1997. A brief inspection carried out in the summer of 1998 in order to assess warranty claims showed no damage to any part except one valve. Experience shows that all aforementioned activities were necessary. The paper reports about success and negative experience. Certification according to DIN EN ISO 9000ff., however, affords to guarantee of high-quality construction. Builders of such plants therefore need to set up their own quality assurance centre and ensure its technical competence. If necessary,additional experts should be called in.Quality assurance costs for HKW 2 came to about 0.5-0.6 percent of total costs. In view of the success and long life of this investment these expenses are more than justified. (orig.) [German] Nach ...
Maintenance of power stations so far operated on the concept of using or extending the expected service life of a machine or plant as far as possible in order to avoid early and costly replacement. This was done by means of time-oriented maintenance, inspection and repair, otherwise called preventive maintenance. A European study on maintenance methods totals the cost of these measures at between 140 to 200 billion DM. One way of reducing these costs is 'predictive maintenance'. Estimated savings are about 8 percent or between 12 and 16 billion DM per year. Predictive maintenance identifies irregulaties of machine parts at an early point in time by means of condition monitoring and can help to cut costs: unplanned repairs can be avoided; repairs can be fitted into production schedules; production will not be disturbed to to unforeseen repairs, optimised spare part warehousing helps to cut costs. Predictive maintenance aims at keeping availability high, give maximum ...
MRI provides a non-invasive diagnostic tool complementing echocardiography on one hand, and showing advantages over echocardiography, on the other hand, especially after corrective procedures. The multiple different MRI sequences need to be adapted to examinations of children and patients with congenital heart disease (CHD), and can be used to detect morphologic changes, blood-flow in the heart and thoracic vessels and diastolic or systolic function of myocardium. Several factors determine the success of the examination of a complex congenital heart disease or a postoperative situs. Pediatric radiologists and radiologists experienced in congenital heart diseases have to work in close cooperation. Echocardiography should be performed before MRI. The results of prior examinations and the clinical history of the patients, including possible palliative or reconstructive operations, must be available before MRI to guide the planning of the examination. With a systematic segmental approach ...
Nuclear medicine and magnetic resonance imaging (MRI) are widely used in cardiac diagnostics. Both techniques have been carefully evaluated and are equivalent for the assessment of regional and global wall motion as well as the evaluation of ejection fraction and cardiac volumes, though MRI is herein currently seen as gold standard. For evaluation of myocardial perfusion, extensive data exist for nuclear imaging, that, next to high diagnostic accuracy for evaluation of coronary artery disease, show incremental prognostic information and allow for independent risk stratification. Because of rapid technical advance, myocardial perfusion imaging has also become feasible with cardiac MRI. Results of recent studies are promising, but the data are few compared to perfusion scintigraphy. For viability assessment in patients with ischemic cardiomyopathy, positron emission tomography (PET) with FDG is currently seen as gold standard. However, single photon emission computed tomography (SPECT) ...
The development of new steels is always a challenge for the manufacturer of filler metals. In many cases it is obvious that some properties of the base metal cannot be fulfilled with matching filler metals. In some cases, dissimilar filler metals can solve the problem in some cases, there is no chance to meet the requirements of the base metal (for example yield strengths of new ultra high strength steels). This paper deals with different kinds of new steels and the requirements for the weld metal with examples from motor car industry (Mangan Austenite), crane (Ultra high strength steels), earthmoving machinery (Wear-resistant steels) and offshore (Supermartensitic steels). Specific problems will be discussed and best solutions will be highlighted. These examples make clear that the success of new kinds of steels in the market depends on solving the joining problems of these steels. (Abstract Copyright [2007], Wiley Periodicals, Inc.) [German] Die Entwicklung von neuen Staehlen ist ...
The paper addresses the major items of relevance to compensation for nuclear damage under civil liability law. The revision of the Vienna Convention deserves support as a contribution to enhancing the protection of those who suffered damage, and of the environment. The results of the revision will have an impact on the liability regimes in existing and future signatory states, and to some extent will also set the goals of a future reshaping of the Paris Convention, all the more since the Joint Protocol calls for harmonization of at least basic provisions of substantive law in the two Conventions. (orig./HP) [Deutsch] Es werden die wesentlichen Punkte dargestellt, die fuer die zivilrechtliche Praxis im Schadensfall von Belang sein koennten. Die Revision ist als Beitrag zu einem verbesserten Schutz Geschaedigter, aber auch der Umwelt zu begruessen und zu unterstuetzen. Die Ergebnisse werden sich auf die Rechtsordnungen der gegenwaertigen und zukuenftigen Vertragsstaaten auswirken und ...
The nozzle-group regulation of steam turbines plays furtheron an important role in the operation of power stations owing to modern, adaptable control-technical valve timing possibilities. New procedures for a choice-connection of different nozzle areas via the control valves as well as the use of valve laps require, however, a differentiated consideration of the loss mechanism in the inlet area of the turbine, in order to be able to assess and minimize its specific heat consumption also at the operational points outside the layout- and calculation-technically fixed guarantee or valve points, respectively. The basic technical-physical stages to this are explained. (orig.) [Deutsch] Die Duesengruppenregelung von Dampfturbinen nimmt nicht zuletzt dank moderner, anpassungsfaehiger leittechnischer Ventilansteuerungsmoeglichkeiten weiterhin eine bedeutende Stellung beim Betrieb von Kraftwerken ein. Neue Verfahren zur wahlweisen Zuschaltung unterschiedlicher ...
In a case study of the River Lahn, Hessen, Germany, the ecological impact of effluents from sewage treatment plants was investigated. These emissions have a significant impact on the receiving water quality with ammonia, nitrite, phosphorus and the eutrophication as most important factors. Current legislation standards seem to be sufficent for the sanitation of the nitrogen load. The potential of phosphorus removal in sewage treatment plants however may not reach the demand for eutrophication abatement. Therefore, integrated and immission oriented strategies are required including in site measures of river restoration. (orig.) [Deutsch] An der hessischen Lahn wurde in einem mehrjaehrigen Forschungsvorhabens die Bedeutung von Abwasserereinleitungen aus Klaeranlagen hinsichtlich ihrer gewaesseroekologischen Relevanz untersucht. Wesentliche Belastungen beziehen sich auf die Parameter Ammonium, Nitrit und Phosphor sowie eutrophierungsbedingte Folgeerscheinungen. Waehrend ...
Clinical information is indispensable for swift and cost-effective clarification of diseases of the larynx. While quality clarification of neurological changes in the area of the posterior cranial fossa and in the course of the vagus nerve as a cause of glottis malfunction is possible with MRI, localized disease of the larynx can more effectively be assessed with low-artifact CT. In the particularly difficult assessment of the post-operative larynx, a recurrence can be diagnosed only after a baseline study has been carried out after the end of therapy. With knowledge of the pretherapeutic findings, the findings immediately post-therapy, and the operation technique used, the optimal CT examination, which can be carried out quickly, will be able to provide more information about recurrence. (orig.) [Deutsch] Zur schnellen und kostenguenstigen Abklaerung von Erkrankungen des Larynx ist die klinische Information unabdingbar: Wenn neurologische Veraenderungen im Bereich ...
Purpose: Reconstruction of organ doses of selected organs and tissues from radiographic settings and exposure data collected during chest X-ray examinations of children of various age groups performed in Dr. von Hauner's Kinderspital (children's hospital of the University of Munich, DvHK) between 1976 and 2007. Materials and Method: The dosimetric data of all X-ray examinations performed since 1976 at DvHK were stored electronically in a database. After 30 years of data collection, the database now includes 305 107 radiological examinations (radiographs and fluoroscopies), especially 119 150 chest radiographs of all age groups. Reconstruction of organ doses in 40 organs and tissues in X-ray examinations of the chest was performed based on the conversion factor concept. Results: The radiation exposure of organs in projection radiography is determined by the exact site of the organs relative to the edges of the X-ray field and the beam direction of X-rays. Optimal ...
Purpose: Reconstruction of radiation doses for the thoracoabdominal babygram and the abdomen X-ray from radiographic settings and exposure data acquired at Dr. von Hauner's Kinderspital (children's hospital of the University of Munich, DvHK) between 1976 and 2007; comparison of these dose values with values reported in the literature; recommendation of a reference dose value for the thoracoabdominal babygram. Materials and Methods: The data from all X-ray examinations performed since 1976 at DvHK were stored electronically in a database. After 30 years of data collection, the database now includes 305 107 radiological examinations (radiographs and fluoroscopies), especially 1493 thoracoabdominal babygrams and 3632 abdomen X-rays of newborns and young infants. With the computer program PAeDOS, a specific dose reconstruction algorithm was developed. Results: the entrance dose values of thoracoabdominal babygrams and abdomen X-rays in DvHK could be reduced in the last 30 ...
As an alternative to the usual way of installing wind machines in extended windfarms new concepts are being developed. Several wind turbines are affixed to one support structure and can be aligned together. Drafts of steel constructions developed by students in three diploma theses are presented. The attempt to transform existing design standards requires extensive discussion of possible influence scenarios. Several concepts regarding structure and safety elements are described and evaluated. The design of the support structure is to be seen as a first step to the practicability of the whole concept. A preliminary mass calculation and a specification of further cost factors facilitates the comparison to conventional wind power stations. (orig.) [Deutsch] Als Alternative zur ueblichen Praxis, Windenergieanlagen in Form grossflaechiger Windparks zu bauen, werden Konzepte entwickelt, bei denen mehrere Konverter an einem Tragwerk angeordnet und ...
More than two and a half years of monitoring of a passive house school and day-care centre in Frankfurt a. M. show comfortable indoor climate and good air quality. The space heat consumption is low and shows savings of approximately 90 % as compared to average existing schools. Excellent performance was also achieved in terms of primary energy. The results of further analyses of the efficient ventilation system with heat recovery, the perimeter insulation as an alternative to floor slab insulation and the influence of the air change due to the entrance door are presented. (Abstract Copyright [2008], Wiley Periodicals, Inc.) [German] Ueber zweieinhalb Jahre Monitoring einer Passivhaus-Schule und Kindertagesstaette (KiTa) in Frankfurt a.M. zeigt behagliche raumklimatische Bedingungen bei guten Luftqualitaeten. Die Heizwaermeverbrauchswerte liegen wie erwartet niedrig und zeigen Einsparungen um 90 % gegenueber dem Durchschnitt im Bestand. Auch primaerenergetisch ...
Policy strategies for the promotion of electricity from renewable energy sources differ significantly among the Member States of the European Union with respect to the amount of additional installed capacity as well as concerning the country-specific support costs. The present report aims to assess the effectiveness and the economic efficiency of the support policies in the EU based on both historical experiences and prospective model-based analysis. The main message of the investigation is that the most effective policy instruments tend to be cost-efficient at the same time. In particular, feed-in tariff systems were identified as a successful instrument for supporting renewable energies in terms of effectiveness and efficiency, whereas quota systems still have to prove themselves in practice. (orig.) [German] Bezueglich des Erfolges bei der Foerderung erneuerbarer Energietraeger im Stromsektor bestehen deutliche Unterschiede zwischen den Mitgliedsstaaten der ...
Buildings in the USA are commonly not perceived as energy efficient and sustainable. Considering this, it comes as a surprise that the LEED (Leadership in Energy and Environmental Design) certification system is leading the process to certify ''Green Buildings'' despite the broad range of certification systems in countries such as BREEAM in England, CASBEE in Japan, HQE in France, Green Star in Australia, and most recently DGNB in Germany. International companies are pursuing the LEED certification due to its worldwide applicability - over 20,000 buildings in 76 countries are currently registered. (Abstract Copyright [2009], Wiley Periodicals, Inc.) [German] Die USA sind nicht gerade fuer oekologisches und energieeffizientes Bauen bekannt. Umso erstaunlicher ist es, dass das LEED-Zertifizierungssystem (Leadership in Energy and Environmental Design) neben anderen landesspezifischen Systemen wie z. B. BREEAM in England, CASBEE in Japan, HQE in ...
The direct injection Diesel engine with its specific fuel consumption of about 200 g/kWh is one of the most efficient thermal engines. However in case of relatively low CH- und CO-emission the soot- and NO{sub x} concentration in the exhaust gas turns out to be a problem with respect to the legislation on emission limits. At the department of piston- and turbo-machines of the Trier University of Applied Sciences, a single-cylinder testing engine with two injection-systems (fuel and water) has been developed. This engine has been constructed to analyse the effect of stratified water-injection on the soot- and NO{sub x} emissions of exhaust gases of a Diesel engine. (orig.) [German] Der Dieselmotor mit Direkteinspritzung stellt mit spezifischen Kraftstoffverbraeuchen in der Groessenordnung von 200 g/kWh eine der wirtschaftlichsten thermischen Kraftmaschinen dar. Bei relativ niedrigen Kohlenwasserstoff- und Kohlenmonoxid-Emissionen erweist sich die Russ- und ...
Experiments for lifetime prediction of the first wall are being carried out within the framework of the European fusion reactor programme. Defects such as notches and cavities may develop in the first wall and may initiate under cyclic thermal stress cracking processes which may reduce the service life of the material. For examination of crack growth, specimens with defined initial notches were prepared and subjected to cyclic thermal loads. The paper shows that the eddy current method is suitable for detecting and revealing the crack growth processes even under conditions of complex geometry, as e.g. cracks in inner bores. The experiments indicated particularly susceptible, critical spots in the first wall and yielded crack growth rates of use for lifetime calculations. (orig./CB) [Deutsch] Im Rahmen des europaeischen Fusionsreaktorprogramms werden Untersuchungen zur Lebensdauervorhersage der Ersten-Wand durchgefuehrt. Die Erste-Wand kann Fehler in Form von ...
Evaluation and interpretation of CT colonography is based on both 2D and 3D techniques. The 2D techniques are popular mainly because the time needed for evaluation is short. The 3D techniques allow better definition than the 2D techniques, especially of polyps close to folds or at the base of a fold. The evaluation strategies generally accepted so far (primarily 2D, with 3D for problem cases, or vice versa) demand knowledge of both 2D and 3D techniques. Newer 3D visualization techniques help make it possible to acquire more complete and faster recording particularly of areas that are not easily accessible to endoscopic examination. These user-friendly developments are thus well suited to improving the detection and the security of detection of polyps. It must be remembered that experience and the knowledge of associated artifacts and the limitations they can impose on diagnosis are prime requirements for the implementation of such visualization techniques. (orig.) [German] Die ...
Introduction: The goal of this study was to compare contrast-enhanced T1-weighted Flash and Turbo-Flash sequences with conventional spin-echo sequences as a basis for planning high-precision radiotherapy. Methods: A total of 25 consecutive patients with different intracranial tumors and a disrupted blood-brain barrier were studied. T1-weighted Flash, Turbo-Flash and conventional spin-echo images were evaluated after controlled 30-s infusion of 0.1 mmol/kg body weight of Gd-DTPA. The evaluation of the three sequences included the measurement of the signal- and contrast-to-noise ratios, the visual inspection of the tumors and artifacts, and the measurement of tumor size. Results: The signal- and contrast-to-noise ratios were significantly (P<0.05-0.01) lower for Flash and Turbo-Flash than for conventional spin-echo sequences. However, visual inspection of the contrast-enhancing tumors revealed in 23 and 24 of 25 lesions of Flash and Turbo-Flash images, respectively, good or very good ...
This thesis deals with the analysis of dominant loss mechanisms in direct methanol fuel cells (DMFC) and hydrogen fed polymer electrolyte membrane fuel cells (PEFC) by means of experimental characterization and modeling work. Due to different fuels used in these two fuel cell types, the dominant loss mechanisms are different in their nature. All in-situ characterization techniques that are used in this work are based on a novel test fuel cell with embedded reference electrodes. The first part of this work presents a new concept for realizing a reference electrode configuration in a polymer electrolyte membrane fuel cell by means of laser ablation. The laser beam is used to evaporate a small gap into the electrode surface of a catalyst coated membrane (CCM) to isolate the reference electrode from the working/counter electrode (WE/CE). This method enables the simultaneous ablation of the electrodes on both sides of the CCM because the membrane is transparent for the laser beam. ...
The R and D activities of the institute focused on two major projects, ``Molecular and cellular environmental toxicology``, and ``Biophysics of multi-cellular systems``. For assessment of health risks emanating from the uptake of heavy metal compounds, work performed under the first mentioned project studies the formation of allergy-inducing metabolic products from membrane lipids, and the effects of related cellular signaling processes. These studies are accompanied by an approach to quantify and classify the toxicity of environmental organometallic compounds. Another major task is research into the pathogenesis of lung disease induced by dusts, gases, and gas-dust mixtures and the liberation of inflammatory agents by immunological cell reactions (alveolar macrophages). Atomic force microscopy is the tool used to visualize the related dynamic changes in bronchial cells. Studies for detection of the localisation and structure of the Fe-Mo co-factor in nitrogenase by means of the method ...
This assessment is a feasibility study according to ISO 14024. It deals with the question whether an ecolabel is suitable for wood pellet heating systems and how concrete criteria for an ecolabel for wood pellet heating plants could be specified. The study begins with a comprehensive market analysis in order to identify possible plants for which an ecolabel would make sense. In the main part of the study, the environmental relevance of the chosen plants is analysed. For this analysis, plant manufacturers were interviewed and a comparison between wood pellet heating systems and heating systems which use gas, oil or wood was carried out. On the basis of this analysis, it was possible to derive a number of criteria which were discussed with company representatives and other experts in this field. As a result of this dialogue and the investigation process as a whole, the introduction of an ecolabel for wood pellet heating plants can be recommended. Wood pellet heating systems are ...
A cooperative effort of the Center for Solar Energy and Hydrogen Research (ZSW) and Phototronics Solartechnik GmbH (PST) aimed at the transfer of highly efficient solar cells developed on a laboratory scale, to large-area thin-film solar modules suitable for production. This work was based on research and development at the Institute for Physical Electronics (IPE) of Stuttgart University and ZSW on one hand, and on the know-how of PST in regard to large-area module fabrication on the other hand. The various thin-film layers of the cells and modules comprize molybdenum as rear contact, copper-indium(gallium)-diselenide (CIGS) as absorber material, the combination of cadmium sulphide (CdS) and ZnO as window layer. To produce these layers on large areas (30x30 cm{sup 2}), equipment was constructed and procedures were developed. Monolithic series connection of cells, used in other thin-film technologies, was studied and optimized by suitable patterning procedures, such as laser-scribing, ...
Objective: To determine the reproductibility of three-dimensional volume and thickness measurements of the knee joint cartilage with MRI in volunteers. Methods: The knees of 7 healthy individuals (ages 23 to 58 yrs.) were sagitally imaged with a resolution of 2x0.31x0.31 mm{sup 3}, using a fat-suppressed FLASH-3 D sequence. The knee was repositioned in between replicate acquisitions, 6 data sets being obtained in each case. After semiautomatic segmentation and three-dimensional reconstruction of the cartilage, the thickness was determined independent of the original section orientation. The coefficient of variation for repeated volume measurements and the deviations of the maximal cartilage thickness values were calculated subsequently. Results: The mean variation of the cartilage volumes of the replicate measurements was 1.4% ({+-}0.8%) in the patella, 1.7% ({+-}1.5%) in the femur, 3.0% ({+-}1.2%) in the medial tibial plateau and 3.5% ({+-}2.0%) in the lateral tibial plateau. The ...
The fundamental recommendations of the ICRP issued in its publication of 1990 stipulate the general principle of performance of dose measurements at regular intervals in the field of diagnostic radiology, for the purpose of equipment performance checking and optimization of radiological protection. In response to this requirement, the Federal Ministry, in cooperation with experts and the competent supervising authorities, has issued an order to install dose-area-product meters in angiographic examination systems, imaging systems and fluoroscopic screen devices primarily used for examining infants and children up to the age of 12. This is done in response to reported cases of adverse effects of radiation exposure and the high priority given to radiological protection in the examination of infants and children. In 1992, an expert group was convened to discuss and elaborate instructions for including dose-area product measurement in the dosimetry activities in medical diagnostic ...
To evaluate the usefulness of radiation therapy alternative to surgery for clinical N0-N1 non-small cell lung cancer (NSCLC). From 1976 through 1989, 116 patients with NSCLC without mediastinal involvement were treated with definitive radiation therapy alone at Gunma University Hospital. All patients were treated with once-daily standard fractionation using 10 MV X-rays. The total dose ranged from 60 Gy to 80 Gy. The actuarial 2- and 5-year survival rates of the entire group were 43% and 20%, respectively with a median survival time of 19 months. The survival of 76 patients with stage T2 tumors was significantly better than that of 28 patients with T3 tumors (mean survival time 21 versus 15.5 months; p<0.05). Sixty-two patients with tumors less than 5 cm in diameter had a 2-year progression rate of 20%, in comparison with 39% of 54 patients with tumors greater than 5 cm. The difference of survivals for these 2 groups was statistically significant. Twelve patients given a total dose ...
The quantitative measurement of carbon concentration-distance curves serves as fundamental prerequisite for the evaluation of rim zone properties connected with decarburisation processes in material science. This was shown in part 1 of the present work with two samples from through-hardenable rolling bearing steel 100Cr6 (SAE 52100) austenitised in different oxidising atmospheres by position dependent determination of hardness, residual stresses, and X-ray line broadening ({l_brace}211{r_brace} {alpha}'-Fe diffraction line). In practice, it is important to predict carbon concentration-distance curves under prevailing heat treatment conditions or to conclude conversely from profile measurements. Based on a refined kinetics model of a diffusion-controlled process, part 2 therefore presents a simulation tool developed by means of the finite element method (FEM). Apart from the concentration dependence of the diffusion coefficient, it also considers the decarburisation induced ...
Purpose: To evaluate the success rates of the implantation of stent grafts in the treatment of peripheral aneurysms. Materials and methods: in 13 patients with 15 aneurysms at the common iliac artery (n = 6), external iliac artery (n = 1), hypogastric artery (n = 2), femoral artery (n = 2) or popliteal artery (n = 4), implantation of dacron-covered nitinol stents was performed. The patients were followed up for three to 20 months (mean, 8.8 months) with intravenous digital subtraction angiography, CT or colour-coded Doppler sonography. Results: In all cases, the aneurysm was successfully occluded after stent implantation. In one case with a popliteal aneurysm, kinking of the vessel caused thrombosis of the stent. The stent was successfully reopened. The aneurysm however, had to be surgically treated 9 months later. The primary and secondary patency rates at 6 months were 93% and 100%, respectively. Conclusion: The method described might be an alternative therapy to surgery. There are ...
This feasibility study of the uve Institut fuer Technische Chemie und Umweltschutz GmbH discusses the scientific and technical fundamentals of a catalytic process for complete removal of organic pollutants (PAH, H-HC, PCB, phenols, nitro-aromatics and organometallic compounds, e.g. from polluted soil and groundwater) by thermal-catalytic cracking and conversion into simple gases. The process is based on the catalytic reaction of the hydrocarbon compounds with water vapour in the temperature range of 700-900 degrees centigrade. The resulting gas mixtures consist mainly of hydrogen, carbon monoxide, carbon dioxide and methane which can be used as fuels, e.g. for heating or in gas engines. The process is an alterntive to combustion. It is therefore well suited whenever the pollutant to be removed is already mixed with water or water vapour and wherever in-situ removal would be too great a hazard. [Deutsch] Die vorliegende Machbarkeitsstudie aus dem uve Institut fuer Technische Chemie und ...
Nickel-based alloys are presently used as brazing filler metals for components which undergo mechanical stress in corrosive conditions, f. e. heat exchangers. When soldering chrome containing steel parts with nickel based brazing filler metals additionally containing boron and silicon a reaction of chrome and boron can occur. This evolution of chromium borides, depositing on grain boundaries, causes a lack of chrome in the steel part. A drop of the chrome content in the parts below 13 % leads to a loss of corrosion resistance. It is possible to change the microstructure of brazing joints by modification with chromium and molybdenum. Continuous brittle phases could be successfully avoided with this modification. Furthermore it could be shown that the choice of additives, the heating respectively cooling rate and the brazing temperature have important influence on the microstructure evolution and therefore on the mechanical and corrosive properties of joints. (Abstract Copyright [2008], ...
This contribution provides an overview and imparts basic knowledge on pertinent technical developments in magnetic resonance imaging (MRI) of the liver: 3D sequences, respiratory triggering, parallel imaging, and 3 Tesla (3T). 3D sequences can be used as T1-weighted (T1w) sequences for analyzing dynamics of contrast enhancement or as T2w sequences for MR cholangiography. Consistent improvements in respiratory triggering make it possible to obtain good image quality on T2w scans even in patients unable to hold their breath. Parallel imaging as a universal technique to accelerate image acquisition is particularly appropriate for MRI of the liver, and it has been shown that the reduced acquisition time is not achieved at the expense of image quality. Further progress in MRI of the liver can be expected with use of the 3T systems, but hitherto irrelevant problems must still be solved. Overall the innovations presented here, applied alone or in combination, facilitate rapid, robust, and ...
When the use of retarders in utility vehicles increased in the middle of the 80s, the Forschungsvereinigung Automobiltechnik (FAT) commissioned a study on the safety aspect of this braking technology in trucks. Retarders are wear-free permanent brakes that are fitted in the drive transmission system of utility vehicles, thereby generating braking forces only at the wheels of the live shaft. The question of the possible overbraking of the live shafts was just as well investigated as the interaction between the retarder and service brake in so-called integrated braking systems, and both under conditions of low adhesion as well as in the border area of the dynamics of vehicle movement. This subject met with considerable joint interest on the part of the motor vehicle industry as well as of manufacturers of towed vehicles and unit sets. FAT, therefore, commissioned the Institut fuer Kraftfahrwesen of the University of Hannover to carry out a three-phase research project on the braking ...
Parallel imaging and echo sharing techniques have markedly reduced the acquisition times for MRI of large volumes. Dynamic 2 and 3-dimensional data sets of the chest with high temporal resolution (up to 10 images/s with single slice and 2 volume/s) allow an analysis of respiratory motion of the lungs and tumors. Time-resolved 2D series in preselected planes can be used to observe respiratory motion during free breathing or after respiratory commands, e.g. to exclude chest wall invasion by a tumor or for diagnosing impairment of respiratory mechanics. Time-resolved 3D-series (4D-MRI) allow monitoring of the spatial displacement of the lungs and tumors as a whole volume. Present limitations such as an overestimation of tumor size and an underestimation of displacement due to a limited temporal resolution are expected to be overcome with further technical developments. However, 4D-MRI already appears to be the appropriate tool to select patients for motion-adapted radiotherapy. In ...
Already in 1998, the city of Hanover, the Stadtwerke Hannover and six further cities of the region initiated the funding programme 'Hannover proKlim' for promoting energy-relevant modernization measures in domestic buildings. One year later, the social marketing campaign 'Haus-Partner Hannover / Der (H)Eissbaer'' was started, which addresses building owners in Hanover with the intention to induce them to action. The 'Energiepass Hannover' is another important instrument of the campaign. This report takes stock of the results achieved so far. [German] Beim Klimaschutz im Gebaeudebestand lassen sich in Hannover drei Ansaetze hervorheben, die parallel zueinander entwickelt wurden und die in besonderer Weise dazu beitragen, die CO{sub 2}-Emissionen im Gebaeudebestand zu reduzieren: Bereits 1998 hat die Landeshauptstadt Hannover gemeinsam mit den Stadtwerken Hannover und sechs weiteren Staedten der Region den Klimaschutz-Fonds ...
Purpose: Budd-Chiari syndrome is a fairly uncommon disease in Europe. This often leads to its late diagnosis. The syndrome is characterised by portal hypertension and splanchnic congestion due to obstruction of hepatic venous outflow. This paper describes the treatment of three patients with Budd-Chiari syndrome by interventional therapeutic techniques and discusses alternative treatment modalities. Patients and Methods: The first patient presented with veno-occlusive disease and was treated by the placement of a transjugular intrahepatic portosystemic stentshunt. The second patient showed an occlusion of the major hepatic veins. After percutaneous recanalisation, a stent was placed in the right hepatic vein which remained patent. The third patient had a membranous obstruction of the right hepatic vein which was treated by percutaneous balloon dilatation. Results: In all patients the clinical symptoms resolved completely after treatment and no complications were encountered. ...
Materials and methods: 12 patients with 22 coronary bypass grafts underwent intraoperative flow quantification using the transit time ultrasound method. These values were compared to postoperative MR phase shift measurements. Flow measurements were performed preoperatively in 28 coronary arteries of 20 patients. For flow measurement, we used a velocity-encoded k-space segmented gradient echo sequence with a temporal resolution of 110 or 125 ms, respectively. 6-8 pase shift images could be acquired during one cardiac cycle. Results: There was a significant correlation between intraoperative and flow measurements using velocity-encoded MR imaging (r=0.76, p<0.0001, t-test). Flow volumes determined by MR imaging were systematically larger than those determined by the transit time ultrasound method. Mean flow in coronary arteries was reduced in severely stenosed vessels (>70%) compared to normal vessels. Intra- and interobserver variability were 10.5 and 15% (coronary bypass ...
Purpose: Measurement of the oscillating CSF flow in the spinal canal (SC) of healthy volunteers and in patients with post-traumatic syringomyelia (PTS) using an optimized MRI protocol as well as to determine whether stenosis induced velocity changes are detectable using MRI. Methods: In 68 healthy volunteers quantitative studies of CSF flow in the cervical, thoracic, and lumbar regions were performed. First, an optimized sequence was developed and tested in 19 volunteers using four different flow-encoding velocities (4, 8, 12, 16 cm/s). Secondly, the optimized sequence was employed in 49 volunteers to measure the different CSF patterns in the cervical, thoracic, and lumbar spinal canals (CSC, TSC, LSC). Part three of the study, in which patients with PTS are being examined is still underway. We measured the maximum velocity (cm/s), the pixel area (mm{sup 2}), and the stroke volume (ml/s). Using a flow model the velocities prior to and after compression with 5 different power levels ...
Purpose: To report the detection of con-compacted ventricular myocardium (NVCM) with MRI compared to echocardiography in 8 patients. Material and methods: Non-compaction of the ventricular myocardium is a congenital disorder characterized by an altered structure of the myocardial wall resulting from an intrauterine arrest in endomyocardial embryogenesis. The morphological findings consist of a prominent meshwork of multiple myocardial trabeculations and deep intertrabecular recesses, communicating with the left ventricular cavity. 8 consecutive patients (mean age 7.3 years) with clinical and echocardiographic signs of NCVM were examined by MRI (1.5 T, Vision, Siemens) in short axis and 2- and 4-chamber views, using T{sub 1}-weighted TSE and Cine-GRE in 6 patients and true FISP sequences in 2 patients. MRI and echocardiography were evaluated for visibility, signs of NCVM and involvement of myocardial wall segments. Thickness was measured for non-compacted and compacted myocardium and ...
Pr{sub 2}[Mo{sub 2}C{sub 3}] was obtained by arc melting of the elements followed by annealing at 1500 C in arc welded and sealed Mo-ampoules. The compound was characterised by chemical analyses, X-ray diffraction and metallography. The crystal structure (monoclinic, P2{sub 1}/c, Z = 4, a = 597.99(10) pm, b = 665.15(11) pm, c = 1185.60(19) pm and {beta} = 111.631(5) ) represents a new structure type containing a three dimensional polyanion {sub {infinity}}{sup 3}[(Mo{sub 2}C{sub 3}){sup 6-}] with Molybdenum(III) in a distorted tetrahedral coordination by carbo-ligands. Tetrameric building-blocks, Mo{sub 4}C{sub 10}, of edge sharing MoC{sub 4}-tetrahedra are arranged to form layers running parallel to (100). The layers are interconnected along [100] by sharing common apices of the MoC{sub 4} tetrahedra. The coordination polyhedra around praseodymium represent distorted (PrC{sub 5})-arrangements (mono capped tetrahedra and square pyramids). The metal atoms together form a distorted motif ...
Purpose: To report on the nephron-sparing, percutaneous ablation of a large renal cell carcinoma by combined superselective embolization and percutaneous radiofrequency ablation. Materials and Methods: A 5 cm renal cell carcinoma of a 43-year-old drug abusing male with serologically proven HIV, hepatitis B and C infection, who refused surgery, was superselectively embolized using microspheres (size: 500 - 700 {mu}m) and a platinum coil under local anesthesia. Percutaneous radiofrequency ablation using a 7F LeVeen probe (size of expanded probe tip: 40 mm) and a 200 Watt generator was performed one day after transcatheter embolization under general anesthesia. Results: The combined treatment resulted in complete destruction of the tumor without relevant damage of the surrounding healthy renal tissue. The patient was discharged 24 hours after RF ablation. No complications like urinary leaks or fistulas were observed and follow up CT one day and 4 weeks after the radiofrequency ...
Purpose: To evaluate a T{sub 2}-weighted URSE sequence for the assessment of pulmonary infiltrations in comparison to CT. Methods: 28 MRT scans of 22 patients with confirmed pneumonia were recorded on a 1.5 Tesla apparatus with an expiratory and diastolic triggered, T{sub 2}-weighted ultrafast-spin-echo sequence in axial slice mode with the following parameters: TR{sub eff}/T{sub E}/Turbofactor 2000-4000/90 ms/21-23; slice thickness/separation 6/0.6 mm; FOV 360 mm; 24 slices. 24 spiral CTs (sice thickness/table advance: 1-2 mm/10 mm) were available for comparison. The separate evaluation of MRTs and CTs was performed by three radiologists in a consensus procedure with regard to pulmonary lesions (e.g., infiltration, round foci, net patterns) and image quality of the MRTs (4-step scale). Results: In 71% of the cases the CTs and MRTs agreed with the diagnosis and representation of the lesions, in 25% MRT was superior. MRT was better for the detection of pulmonary abscesses. In 93% the ...
Purpose: Liposarcoma is the most common soft tissue sarcoma in adults. The purpose of the study was to correlate MR imaging features with the four ICD subclasses. Methods: 28 patients with liposarcoma were examined preoperatively on a 1.0 T MRI system, using spin echo sequences, gradient echo imaging and STIR sequences. In all patients, classification of the liposarcomas was made by histologic diagnosis (ICD-10-M-classification). Results: Well differentiated liposarcomas (9 patients) showed a number of MRI features consistent with lipoma (well defined mass high signal intensity (SI) on T{sub 1} images, low signal on T{sub 2} images, no or only little signal increase of tumour tissue after contrast material application, no necrosis). Not well differentiated liposarcomas (myxoid 14 patients, pleomorphic three patients, round cell two patients) revealed the largest part of the mass to be of low SI on T{sub 1}-weighted images. Only scattered fatty islands and septa (9 patients with myxoid ...
Patients with haemarthros of the knee were examined by MRI and arthroscopy to identify the bleeding source and to determine surgical or conservative therapy. A prospective study was performed on 120 patients who underwent MRI and arthroscopy, point lesions and bleeding sources were documented separately on a standardised form. Arthroscopy demonstrated a ruptured anterior cruciate ligament in 86%, meniscal tears in 55%, disruption of collateral ligaments in 17%, osteochondral lesions in 5% and tears of capsule or plicae in 13%. Disruption of cruciate ligaments caused haemorrhage in all but three cases. In contrast, only meniscal tears located very adjacent to the meniscal basement had bled. Those types of osteochondral lesions caused haemorrhage characterised on MRI by destruction of the subchondral plate and overlying cartilage. Severe lesions of the knee were diagnosed by MRI in 71% to 100%, slight lesions in 13% to 40% of the cases. Single, combined and bland lesions were accurately ...
The further optimisation and improvement of the efficiency of internal combustion engines require the realisation of new technologies leading to a distinctively faster warm-up behaviour of the coolant and lubricants as well as of the engine components after a cold start. In order to achieve reduced fuel consumption and exhaust gas emissions with the help of heat management, the design criteria of innovative cooling systems need to be reflected and adapted to future requirements. The use of intelligent components within the cooling system, such as the 'Stand Alone Rotary Valve' as a thermostat's substitute or the use of coolant pumps with a rotary valve integrated into the pump's inlet chamber, offer new ways to realise in a decisively quicker and more flexible way the appropriate heating up and cooling down procedures at varying driving conditions. A description of both of the intelligent components for the cooling system is given in this paper. The ...
Which imaging modalities are appropriate for the Differential diagnosis of Rheumatic diseases. MRI has far most the highest sensitivity and is unequaled in its brilliant presentation of Anatomy and Pathology. But it is sometimes forgotten, that this is at least in part the result of carefully selected sequences, dedicated to the expected result. In a method totally independent of any result, this should not be the case. In contrary this method should be highly standardised and regardless what will be the findings. This is true for Plain X-ray. It will be shown, that already the outer silhouette of the soft parts with different features of swelling, and differences in density and even more - defects or appositions of the bony silhouette in the majority of cases at least will allow to classify the patient for a group of diseases and in many cases will lead to a definite diagnosis. Differential diagnoses like Rheumatoid Arthritis versus Psoriatic Arthritis or simply but not always simple ...
To compare the accuracy in the detection and staging of various malignant tumors with high resolution whole-body MRI using parallel imaging with whole-body dual-modality PET-CT. Preliminary results of an interim analysis from a prospective, blinded study are presented, in which 20 patients (mean age 59 years, range 27-77 years) with different oncological diseases underwent whole-body dual modality FDG-PET-CT screening for tumor search or staging in case of confirmed or suspected metastatic disease. All patients also underwent whole-body MRI imaging with the use of parallel imaging (iPAT). High-resolution coronal T1w- and STIR-sequences of 5 body levels with 512 x 512 matrix, axial fast T2w imaging of lung and abdomen (HASTE), contrast-enhanced dynamic and static T1w-sequences of liver, brain, abdomen, and pelvis were performed. Using a 32-channel whole-body MRI scanner (Magnetom Avanto, Siemens Medical Solutions) with a total field of view of 205 cm and free table movement, all ...
Dampfturbinen bei hohen Dampfparametern [Study of shaft seals for steam turbines under high steam parameters],. Maschinenbautechnik L5, 27-31 (1966)0 ...
Low energy buildings promise significant energy savings and help climate preservation by cutting down on annual heating requirements to values below 70 kWh per m{sup 2} dwelling space. It is expected that low energy constructions will become the common standard by the year 2000 as a result of the forthcoming energy saving ordinance. For making the introduction and implementation of this standard successful, practical experience will be essential. For this reason, the state government of Hesse has supported respective pilot projects 1987. In 1989 the funding programme `30 low energy buildings in Hesse` has been established. Consecutively - between 1989 and 1993 - 29 buildings were erected. At first, the thermal quality of the crafted building construction including the ventilation systems was checked. Consecutively, energy consumption, indoor and outdoor temperatures were measured over a time span of several years. The experience of the inhabitants was surveyed. The `Institut Wohnen und ...
The obligations under international law to reduce transfrontier air pollution is discussed in five chapters from various aspects. Consequences for the European Communities are gone into in five further chapters. (orig./HP)
The microelectronic cable diagnosis is a substantial tool to determine destruction free the residual strength and the lifetime of laid PE/XLPE medium voltage cables. Fundamentals of the ageing diagnosis and a cost reduced inspection concept are the `Isothermal-Relaxation-Current` Analysis and the Neuro-Fuzzy evaluation software. These new tools are able to determine the ageing status of the investigated cable without any references. The authors also show that the test breakdown during the assessment of the ageing status of criterial systems can be reduced by this approach. The cable diagnosis equipment KDA is also useful for the steering of investment as well as for preventive maintenance. (orig.) [Deutsch] Die zerstoerungsfreie dielektrische Kabeldiagnostik kann heute einen wesentlichen Beitrag zur Bestimmung der Restfestigkeit und der Restlebensdauer eines PE/VPE-isolierten Mittelspannungskabels leisten. Basis der Alterungsdiagnose und des Konzeptes ...
This article describes the processes for the treatment of plastic waste: sampling, sorting, comminution. The requirements for the different processes for waste treatment (as recycling, utilization as raw material, energy recovery, combustion) are listed. (SR)
The report provides and overview of calculation models for the simulation of airflows and deals comprehensively with field and multi-zone models as well as the coupling of individual zone and multi-zone models. Examples of calculations are given. figs., tabs., refs.
Fundamental investigations into the biosorption of environmentally relevant heavy metals were carried out with different microbial adsorbents, and processes were proposed for industrial effluents. In order to improve the technology of biosorption processes, attempts were made to improve the sorption efficiency of biological sorbents, and investigations were carried out on the immobilisation of biological adsorbents. (orig.) [Deutsch] Es wurden Grundlagenuntersuchungen zur Biosorption von umweltrelevanten Schwermetallen mit verschiedenen mikrobiellen Adsorbentien durchgefuehrt und an technischen Abwaessern Technologievorschlaege erarbeitet. Zur Verbesserung der Technologie von Biosorptionsprozessen wurden Moeglichkeiten der Steigerung der Sorptionsleistung von Biosorbentien erarbeitet und Untersuchungen zur Immobilisierung der biologischen Adsorbentien durchgefuehrt. (orig.)
In an epidemiological study of the somatic late effects risk following incorporation of a short lived {alpha}-emitter, 1473 ankylosing spondylitis patients treated with repeated intravenous injections of {sup 224}Ra in the years 1948 - 75, have been observed in the GSF. The usual therapeutic plan consisted of a total of 10 - 12 injections of 1.036 MBq (28 {mu}Ci) of {sup 224}Ra each, given at weekly intervals; this would result in an cumulative {alpha}-dose of 0.56 - 0.67 Gy to the marrow-free skeleton of a 70-kg-man (standard man). These patients have been followed together with a control group of ankylosing spondylitis patients not treated with radioactive drugs and/or X-rays. Until May 1993 (mean follow-up time 19.9 yr), 595 patients of the exposure group and 722 patients of the control group have died, causes of death have been ascertained for 578, resp. 668 patients. Among others we observed in the exposure group 10 cases of leukaemia (vs. 2.7 - 2.8 cases expected, p < 0.001) ...
Magnetic resonance imaging (MRI) as a diagnostic imaging tool relies on the generation of magnetic fields, whereas the computerized tomography (CT) uses X-radiation. The fundamental principle of MRI is the magnetic resonance of paramagnetic atomic nuclei. These nuclei, as e.g. protons (= hydrogen nuclei), are aligned in required orientation by application of a strong magnetic field. Upon simultaneous application of an electromagnetic high-frequency field perpendicular to the axis of the basic magnetic field, and in response to periodical changing of the electromagnetic field at a given frequency, the originally aligned paramagnetic nuclei are forced into a movement similar to that of a ``whipping top``. When the resonance frequency is shut off, the nuclei return to their former, aligned positions, inducing a weak signal in a coil. The series of signals generated by multiple repetition of this process of excitation of nuclei and their return to aligned rest is used as input to a ...
Purpose: {sup 31}P-MRS is used to assess the influence of sex and age on quadriceps muscle metabolism before and after exercise. Materials and Methods: 32 healthy volunteers (15 women, 17 men; mean age: 38{+-}17 yrs.) were examined by dynamic phosphorus-31 ({sup 31}P) magnetic resonance spectroscopy (MRS). In the magnet, the quadriceps muscle was stressed by an isometric and an isotonic form of exercise until exhaustion, respectively. Results: Resting conditions: With increasing subjects` age, the ratio {beta}-adenosine triphosphate/total phosphate decreased (r=-0.37; p=0.02). With increasing subjects` age, the ratios inorganic phosphate/phosphocreatine (r=0.79; p=5x10{sup -8}), phosphomonoester/{beta}-adenosine triphosphate (r=0.74; p=10{sup -6}) and phosphodiester/{beta}-adenosine triphosphate (r=0.62; p=10{sup -4}) increased. The pH was the only one of the evaluated spectroscopic parameters which showed a sex-dependence: Female subjects had a significantly lower pH (7.03{+-}0.02) ...
Tumours lesions of the temporal bone and of the cerebello-pontine angle are rare.This tumours can be separated into benign and malignant lesions. In this paper the CT and MRI characteristica of tumours of the temporal bone and the cerebello-pontane angle will be demonstrated. High resolution CT (HRCT) as usually performed in the axial plane are using a high resolution bone window level setting, coronal planes are the reconstructed from the axial data set or will be obtained directly. With the MRI FLAIR sequence in the axial plane the whole brain will be scanned either to depict or exclude a tumour invasion into the brain. After this,T2-weighted fast spin echo sequences or fatsuppressed inversion recovery sequences in high resolution technique in the axial plane will be obtained from the temporal bone and axial T1-weighted spinecho sequences before and after the intravenous application of contrast material will be obtained of this region. Finally T1-weighted spinecho sequences in high ...
In order to remove ash from coal, it is introduced into an aqueous ash removal solution, which contains nitric acid or citric acid and ammonium hydrogen fluoride. The coal without ash is then separated from the aqueous solution. According to the process, either finely ground coal is introduced into the ash removel solution or the coal with the solution is ground in a wet pulveriser.
TENSOMAX enables on-line monitoring of the thermal stress of the shaft to be performed in steam turbines, for which the TURBOMAX probe cannot be installed near the critical area of the shaft. TENSOMAX provides an alternative to the TURBOMAX with a slightly reduced accuracy of the simulation of the temperature distribution in the shaft. The high value placed on the operational performance of TENSOMAX remains, viz. that even with older turbines, and particularly in the case of turbines rehabilitated with a new shaft, careful and transparent operation is assured. (orig.) [German] Die Einrichtung TENSOMAX ermoeglicht eine Ueberwachung der thermischen Beanspruchung der Welle bei Dampfturbinen, bei denen die TURBOMAX-Sonde in der Turbine nahe der kritischen Stelle der Welle nicht einsetzbar ist. Daher stellt der TENSOMAX unter Beruecksichtigung minimaler Ungenauigkeit aufgrund der Nachbildung der Waermeuebergangszahl eine vorteilhafte Alternative zum ...
In this study, the bend properties of the single-crystalline molybdenum brazed by using Mo-40%Ru alloys containing boron of 1-6 mass%Ru alloy for the improvement of the joint strength was determined. (orig.) [Deutsch] Durchgefuehrt wurde die Herstellung von Verbindungen aus einkristallinem Molybdaen. Hierbei kamen Mo-40%Ru-Legierungen mit 1 bis 6 Gew.-% Bor als Lotmaterialien zum Einsatz. Festigkeit und Duktilitaet der Verbindungen wurden mittels 3-Punkt-Biegepruefung bei Raumtemperatur und unter fluessigem Stickstoff ermittelt. Die Bruchflaechen der Proben wurden mit Hilfe eines Rasterelektronenmikroskopes untersucht. Die Ergebnisse lassen sich wie folgt zusammenfassen: Der optimale Borgehalt bezueglich Festigkeit und Duktilitaet der geloeteten Verbindung liegt bei 2 Gew.-%. Die entsprechende Probe hat bei einem Biegewinkel von 100 bei Raumtemperatur nicht versagt. Auch unter fluessigem Stickstoff ...
The authors introduce the above electric car. They deal particularly with the vehicle concept, the energy consumption and the emission balance. (orig.).
Aim: The purpose of this prospective study was to evaluate the value of immunoscintigraphy (ISG) with anti-225.28S in clinically suspected ocular melanoma. Methods: For this purpose standardized ISG was performed in 36 patients using both planar acquisition and emission computed tomography (ECT). Ocular melanoma was present in 31 patients. In 21 patients therapy was enucleation of the eye. These specimens were evaluated by histology and immunohistochemistry in 11 of 21 patients. Results: Regarding the clinical diagnosis, ISG was positive only in 15 of 31 patients with ocular melanoma, regarding histology in 11 of 21 and regarding immunohistochemistry in 5 of 6 patients with a positive immunoreaction. 5 patients showed no immunoreactivity, their ISG was negative. Conclusion: Thus a good correlation between ISG and immunohistochemistry was observed. However ISG using the cutaneous melanoma antibody 225.28S cannot be recommended for the diagnostic work-up of an ocular melanoma considering ...
The position paper will provide the basis for further strategies on offshore wind power development in consideration of ecological and conservation aspects. [German] Das Positionspapier des Bundesministeriums fuer Umwelt, Naturschutz und Reaktorsicherheit (BMU) einschliesslich des Umweltbundesamtes (UBA) und des Bundesamtes fuer Naturschutz (BfN) ist Ergebnis der Arbeiten der BMU-Projektgruppe 'Windenergienutzung im Offshore-Bereich im Hinblick auf die BMU-Anliegen'. Es beschreibt den derzeitigen Stand einer Strategie zur umwelt- und naturvertraeglichen Erschliessung der Windenergienutzung auf See (Offshore). Es bildet die Grundlage fuer die Weiterentwicklung dieser Strategie und dabei insbesondere zur Abstimmung mit den Anliegen anderer Bundesressorts und den Kuestenlaendern, sowie zur intensiveren Einbeziehung beteiligter Verbaende und Fachkreise. Vor dem Hintergrund der zur ...
Early recognition of recurrence and work-up of clinically indeterminate lesions may be impaired after reconstruction with silicone implants due to superimposition of the implant or to scarring. This study was undertaken to evaluate the use of contrast-enhanced MRI in patients with silicone implant after breast cancer. Contrast-enhanded MRI was offered to 169 patients. Comparative two- to three-view mammography was also performed in 169 patients, as well as comparative sonography in 144 patients. Conventional imaging and clinical examination detected only 8/13 recurrences, whereas 12/13 were detected by MRI. One recurrence had been visible as a strongly enhancing 2-mm dot in a previous examination (2 years before), but was not called. It was therefore counted as false negative. In addition, multicentricity was detected by MRI alone in two of three cases. MRI correctly diagnosed scar tissue in all cases with indeterminate findings. However, due to false-positive calls caused by enhancing ...
The programme 'Solarthermie 2000' aimed at the testing and optimization of active solar systems, especially for service water heating. Sub-programme 2 was to provide the technical fundamentals and achieve a certain degree of standardization in order to make the technology economically competitive. This necessitated long-term monitoring of a representative number of systems. [German] Im Rahmen des Foerder- und Demonstrationsprogramms Solarthermie 2000, Teilprogramm 2 erfolgt durch die Foerderung von bis zu 100 solarthermischer Anlagen mit Schwerpunkt in den neuen Bundeslaendern eine umfassende Erprobung und Optimierung von Systemen zur aktiven thermischen Sonnenenergienutzung vorwiegend zur Brauchwassererwaermung. Mit dem Teilprogramm 2 sollen die technischen Voraussetzungen fuer einen kuenftigen wirksamen Beitrag der Solarthermie zur Energieversorgung geschaffen und durch Systemstandardisierung die ...
The goal of this project was to develop a new technology for preparing samples for transmission electron microscopy (TEM) on the basis of ion fine beam processing. For this purpose processes of ion-beam-assisted removal (sputtering), separation, sample handling and ion-beam-assisted chemical etching as well of system-inherent components were examined. As an alternative to a Ga-source a liquid-metal ion source based on a AuGeSi alloy was developed, characterised and used in the FIB 4400. [German] Aufgabe des Projektes war die Entwicklung einer neuen Technologie zur Probenpraeparation fuer die Transmissions-Elektronenmikroskopie (TEM) auf der Basis der Ionenfeinstrahlbearbeitung. Dazu wurden Prozesse der ionenstrahlgestuetzten Abtragung (Sputtern), der Abscheidung, des Probenhandling, des ionenstrahlgestuetzten chemischen Aetzens sowie systemeigener Komponenten untersucht. Als Alternative zur Ga-Quelle wurde eine Fluessigmetall-Ionenquelle auf ...
Zusammenfassung Im Jahre 1910 f?hrte der schwedische Internist Hans-Christian Jacobaeus den ersten laparoskopischen Eingriff am Menschen in Stockholm durch. Grundlage seiner Pioniertat waren die tierexperimentellen Studien von Georg Kelling (1866?1945) aus Dresden, der im Jahre 1901 die erste Laparoskopie mittels eines Nitze-Zystoskops am Hund durchf?hrte. Jacobaeus ver?ffentlichte 1910 in der M?nchener Medizinischen Wochenschrift seine Erfahrungen mit den ersten 17 Laparoskopien unter dem Titel: ??ber die M?glichkeit die Zystoskopie bei Untersuchungen ser?ser H?hlen anzuwenden?. Hierbei nutzte er die neue Technik insbesondere zu diagnostischen Zwecken bei unklaren abdominellen Beschwerden und Funktionsst?rungen. Er war auch der Erste, der explizit auf die Gefahr der Darmverletzung bei Er?...
Biosorption behaviour of and toxic effects of heavy metals in submersed and immobilised microorganisms was studied in batches and in continuous processes in an airlift-recycle reactor. Nickel, cadmium, and zinc were used as heavy metals. (orig./VHE) [Deutsch] Am Beispiel einer Naphthalin-2-sulfonsaeure-abbauenden Kultur wurde das Biosorptionsverhalten und die toxische Wirkung von Schwermetallen auf submerse und immobilisierte Mikroorganismen im Batch-Ansatz und im kontinuierlichen Betrieb in einem Airlift-Schlaufenreaktor untersucht. Als Schwermetalle wurden Nickel, Cadmium und Zink eingesetzt. (orig./VHE)
In the first part of this contribution, the definition of reference values is given and the theoretical and practical problems in the application of this concept are discussed. In this connection, the present resources on instrumentation and the technical requirements for dose assessment are described. In the second part, some consequences are taken and proposals for further actions are made. (orig.) [German] Im ersten Teil des Aufsatzes werden Definitionen von Referenzwerten in der radiologischen Diagnostik untersucht und die theoretischen und praktischen Probleme der Umsetzung des gesamten Konzepts eroertert. In diesem Zusammenhang werden auch der gegenwaertige Geraetebestand und die technischen Voraussetzungen zur Dosisermittlung beschrieben. Im zweiten Teil werden daraus Schlussfolgerungen gezogen und Vorschlaege zum weiteren Vorgehen gemacht. (orig.)
In the first part of this contribution, the definition of reference values is given and the theoretical and practical problems in the application of this concept are discussed. In this connection, the present resources on instrumentation and the technical requirements for dose assessment are described. In the second part, some consequences are taken and proposals for further actions are made. (orig.) [German] Im ersten Teil des Aufsatzes werden die Definition von Referenzwerten in der radiologischen Diagnostik untersucht und die theoretischen und praktischen Probleme der Umsetzung des gesamten Konzepts eroertert. In diesem Zusammenhang werden auch der gegenwaertige Geraetebestand und die technischen Voraussetzungen zur Dosisermittlung beschrieben. Im zweiten Teil werden daraus Schlussfolgerungen gezogen und Vorschlaege zum weiteren Vorgehen gemacht. (orig.)
This is a process for the manufacture of a filter material for cleaning industrial or internal combustion engine exhaust gases and filter material manufactured according to the process. The filter material is manufactured from the mineralized combustion product of peel of tropical fruits burnt at a temperature of 820/sup 0/C to 840/sup 0/C in an oxidising atmosphere excluding the production of carbon, particularly using banana skins and orange peels, which product is granulated with carrier materials or compressed.
A programme to optimize the short-term operation planning of hydrothermal system scheduling is presented. Based on heuristics, an operational planning of pumped storage plants and a method for fast evaluations of spot market deals under consideration of load forecast errors was developed. (orig.) [German] Vorgestellt wird ein Programm, das - basierend auf Heuristiken - den kurzfristigen Einsatz eines hydrothermischen Kraftwerksparks optimiert. Im Programm wurde dazu ein Verfahren zur Pumpseichereinsatzplanung und zur sekundenschnellen Bewertung von Spot-Markt-Geschaeften unter Beruecksichtigung von Lastprognosefehlern entwickelt. (orig.)
In Duisburg the Citibank is building a new call center. As an alternative to the conventional switch cupboard technology, an innovative energy bus technology by ABB Gebaeudeautomation is being used: it involves less planning effort, faster start of operation and a shorter construction time, cost saving through lower space and material demand, plus the advantage of flexibility of extension. (orig.) [German] In Duisburg entsteht zur Zeit der Neubau eines Call Centers der Citibank. Dabei wird als Alternative zur herkoemmlichen Schaltschranktechnik die innovative Energiebus-Technik von ABB Gebaeudeautomation eingesetzt: Geringerer Planungsaufwand, schnellere Inbetriebnahme und kurze Bauzeit, Kostenersparnis durch geringeren Platz- und Materialverbrauch sowie flexible Erweiterbarkeit sind die Vorteile. (orig.)
This publication contains the Ordinance on Heating Costs, the Ordinance on Heating Installations, and the 1st Federal Ordinance on Emission Control (BImSchV) concerning Small-Scale Furnaces, in each case with notes and explanations. All these ordinances aim at reducing energy consumption in connection with heating; the 1st BImSchV also at air pollution abatement by lowering the permissible limiting values for soot and flue gas. The three ordinances also apply to housing property. (HSCH).
Automatic ultrasonic testing is presented as a method for recurrent inspections of pressure gas vessels, from validation to practical testing to customised test applications. National and international regulations and standards are presented along with related implementation problems. [German] Es wird die automatisierte Ultraschallpruefung im Bereich der wiederkehrenden Pruefung von Druckgasbehaeltern, als Alternative zur herkoemmlichen, klassischen Wasserdruckpruefung, vorgestellt. Von der Validierung ueber die praktische Erprobung bis hin zur kundenspezifisch entwickelten Pruefapplikation. Es werden die Anforderungen aus nationalen und internationalen Vorschriften und Normen sowie die damit zusammenhaengenden Umsetzungsprobleme behandelt.
Purpose: Small suspicious breast lesions that are only visible at MR imaging were preoperatively marked with a hook wire under MR-guidance to allow the removal of the lesion with tissue-sparing surgery. Method: In all patients the suspicious lesions were marked preoperatively under MR guidance with a hook wire using a commercially available stereotactic device. Interventions were performed with MR guidance on a 1.0 T and on a 1.5 T system. Results: In 19 patients 22 lesions were localized. One lesion was missed and removed in a second procedure. The mean duration for localization was 66{+-}20 min (range 38-119 min). In two patients two lesions were localized. The mean deviation of the wire tip to the lesion was 2,0{+-}2,6 mm. In this series, 6 of 22 lesions were malignant. The mean diameter of the lesion was 7.6{+-}2.6 mm (range 3-14 mm). Conclusion: Suspicious breast lesions detectable only in MR imaging can be accurately localized with a hook wire preoperatively under MR control to ...
Purpose: To determine the value of MRI in the postoperativ evaluation of a singular ventricle compared to echocardiography and cardiac catheterization. Materials and methods: Thirty-one patients (range: 6 months to 30 years) with a functional single ventricle following palliative corrective operations. Five patients had a Blalock-Taussig-Shunt, 8 patients a Glenn-Anastomosis and 18 a cavopulmonary shunt (6 with classic Fontan-Circulation, 12 with modified cavopulmonary anastomosis). The results in terms of postoperative morphologic changes were compared to percutaneous echocardiography (31/31) and cardiac catheterization (6/31). Results: Echocardiography, which was performed on all patients, could not visualize the entire length of the tunnel, the Glenn-Anastomosis or the central pulmonary arteries in 70% of the patients due to an inadequate acoustic window. MRI was able to show the entire tunnel in 11/12 patients and the central pulmonary arteries in 30/31 patients. The exact anatomy ...
The energy cost of compressors accounts for up to 90% of the total cost. Oil-free compressors could reduce the cost almost by half, i.e. annual savings of 112,500 DM would be achievable. [German] Ueber die Gesamtlaufzeit betrachtet, machen die Energiekosten bei Verdichtern bis zu 90% der Gesamtkosten aus. Deshalb muss bei der Auswahl von Kompressoren dem Energieverbrauch besondere Aufmerksamkeit geschenkt werden. Mit oelfreien Kolbenkompressoren liessen sich in einem speziellen Fall die Kosten fast halbieren, was jaehrlichen Einsparungen von 112 500 DM entspricht. (orig.)
Zusammenfassung Eine genauere Untersuchung der bekannten Modelle isotropen Materialverhaltens (z.B. von Mises, Tresca, Mohr-Coulomb, Drucker-Prager usw.) zeigt, dass sie selten mit Versuchsergebnissen ?bereinstimmen. Modelle mit inkompressiblen Eigenschaften sch?tzen oft das Materialverhalten bei mehraxialen Zugbelastungen falsch ein. Beim Flie?en unter Druck liefern die Modelle mit kompressiblen Eigenschaften unzul?ssige Werte der Querkontraktionszahl. Erfahrungen zeigen, dass es schwierig ist, mehrdimensionales Materialverhalten bei h?ufig fehlenden Informationen werkstoffgerecht abzubilden. Viele Modelle liefern akzeptable Ergebnisse nur f?r bestimmte Bereiche des Spannungsraumes. Diese Beobachtung hat auf die Idee gef?hrt, ,,bew?hrte?? Modelle miteinander zu verbinden. In diesem Artike...
A consequent use of computers and standardized components enables high efficiency for steam turbines while produced at lower manufacturing cost as shown here in the Muehlheim company of Siemens Power Generation, where steam turbines are produced for new stations and retrofitted elder power plants. [German] Auch eine ueber hundert Jahre alte Technik bietet Raum fuer Innovationen: Konsequenter Computereinsatz und standardisierte Baureihen ermoeglichen bei Dampfturbinen hohe Wirkungsgrade bei relativ niedrigen Fertigungskosten - umgesetzt im Werk Muelheim der Siemens Power Generation, wo Dampfturbinen fuer Neuanlagen und zum Modernisieren bestehender Kraftwerke entstehen. (orig.)
Environmental compatibility is nowadays a very important part in the case of planing, construction, operation and maintainance of cable systems. A lot of laws and orders have to be observed. Some new aspects concerning the removal of oil filled cables and the consideration of electromagnetic fields even for cabels will be presented. (orig.) [Deutsch] Der Umweltschutz ist heute unverzichtbarer Bestandteil der Planung, Bau, Betrieb und Instandhaltung von Kabelanlagen. Zahlreiche Gesetze und Verordnungen sind hierbei zu beachten. Der Verfasser stellt einige Neuerungen im Zusammenhang mit dem Ausbau und Oelkabeln vor und erlaeutert die auch bei Kabeln zu beruecksichtigenden elektromagnetischen Felder. (orig.)
ZusammenfassungDie Botulinumtoxinbehandlung ist eine etablierte Methode in der Behandlung von spasmodischen Dysphonien. Prinzipiell kann eine Behandlung transkutan zervikal, transoral mit einer gebogenen Spritze unter visueller Kontrolle w?hrend der Laryngoskopie sowie mittels flexibler Endoskope bzw. Videoendoskope mit Arbeitskanal erfolgen. Insbesondere die transkutane Injektion unter Larynx-EMG-Kontrolle (LEMG) ist ein verh?ltnism??ig einfaches Verfahren. Aufgrund der visuellen Kontrolle bei transoral oder flexibel transnasal verabreichtem Botulinumtoxin scheint eine bessere Wirksamkeit zu bestehen. Aus verschiedenen Gr?nden kann dieses Verfahren aber nicht bei allen Patienten verwendet werden. Wir berichten ?ber unsere Erfahrungen mit den verschiedenen Techniken und unsere Erw?gungen i...
Turbine sets are inspected at their overhaul intervals throughout their operating lives. Using three examples, the present article describes the procedure in the inspection and assessment of steam turbines during overhauls and also deals with rehabilitation measures. In addition to the usual non-destructive tests and the recording of findings, computational life assessments are also considered. (orig.) [Deutsch] Turbosaetze werden waehrend ihrer Betriebszeit anlaesslich von Revisionen ueberprueft. Anhand von drei Beispielen wird in diesem Beitrag die Vorgehensweise bei der Pruefung und Bewertung von Dampfturbinen bei Revisionen und fuer Rehabilitationsmassnahmen dargestellt. Neben ueblichen zerstoerungsfreien Pruefungen und Befundaufnahmen erfolgten in Verbindung damit auch rechnerische Lebensdauerbewertungen. (orig.)
Line conditioners control voltage isolated in external conductors. Changes of Stern-Delta connections involve voltage drop in a nonloaded external conductor and are therefore compensated. The payback period of a line conditioner lasts normally between one to three years, according to the investment cost for the alternative medium-sized voltage to be constructed. (GL)
The VerTech Pit Method for wet oxidation of municipal sewage sludge offers an ecologically and economically advantageous alternative for dealing with sewage and special sludges. Europe`s first commercial plant has now been commissioned in Apeldoorn in the Netherlands following industrial-scale trials in the USA. Up to its present stage of operation the plant has achieved a high degree of reduction of solid residues and a favourable resource and environmental profile, thus impressively confirming earlier results. It is amply in keeping with the landfill criteria laid down in the Household Waste Technical Code. Furthermore, the potential sludge throughput has been found to exceed the projected value. [Deutsch] Mit dem VerTech-Tiefschachtverfahren zur Nassoxidation kommunaler Klaerschlaemme steht ein alternatives Verfahren zur Behandlung von Klaer- und Sonderschlaemmen zur Verfuegung, das oekologische und wirtschaftliche ...
A new procedure for an efficient and sparing cleaning procedure of turbines was developed. The procedure uses cleaning and passivation chemicals that solve effectively and homogeneously salt and ferrous oxide coatings from turbines, avoiding attacks from corrosion, plugging and unbalances. In several high-pressure and condensation turbines the cleaning procedure has been already put into practice. (orig.)
Abstract Der folgende Artikel setzt die Reihe unserer ChiuZ-Beitrge zur Chemi- und Biolumineszenz mit einer interessanten und neuen experimentellen Arbeit zum -kalten Licht- spezieller ungesttigter Verbindungen fort, deren Anwendung auch in der modernen Zeit der Nanotechnologie im biochemischen bzw. medizinisch-chemischen Labor vllig neue Akzente gesetzt hat.
A knowledge based system for pitting corrosion is presented. It can be used for material selection for specific pitting corrosion conditions or to check the suitability of a chosen material. The user can enter his own knowledge. The expert system is an integration of traditional expert system technology and neural networks. (orig.)
Old banknotes may be tomorrow's biomass. Experts on biowaste are investigating two new processes for disposal of the 1000 tonnes of old bills sorted out every year which may be an alternative to combustion. The author presents details.
This bibliographical study compiles and analyzes findings about the metabolism and resorption of molybdenum. Besides including studies on the physiology of molybdenum 99, a general survey is given on molybdenum in the environment and on its physiological behaviour. In particular, information on the dependence of molybdenum resorption on various factors, such as the chemical form, antagonisms etc., are gathered from literature. These factors have to be considered for sensibly carrying out necessary experiments.
Giving many examples, the contribution shows how pump operators may influence the life, efficiency and overall cost of their pumps. Further, it is shown that both the detection of unfavourable or non-optimal operating conditions and the identification of causes necessitate extensive knowledge and experience. (orig.)
Tests based on teaching aims, which can be used for objective determination of the level of knowledge of technical college and polytechnic students, are developed at the vocational training centre of the DMT. The data are gathered completely anonymously by a computer program and evaluated economically. (orig.)
The evaluation of possible manufacture-based defects in turbine shafts and housings for component serviceability relevance is of particular interest not only in post-manufacturing NDT but also in evaluation of NDT results obtained by in-service inspections of components with long service lives. The results discussed in the paper are summarized as follows: Most of the examined natural defects in the forgings and castings behave like cracks under the simulated operating conditions and hence may well be evaluated by fracture mechanical methods for their serviceability relevance determined by crack propagation under fatigue, creep and creep-fatigue stress. The empirical correlation of true defect size and US testing results (echo signal, echodynamics, attenuation) permits improved determination of true defect sizes in the turbine components. Care has to be taken to select the proper testing and evaluation methods in compliance with defect types. (orig./MM) [Deutsch] Die ...
FLUTAN is a highly vectorized computer code for 3D fluiddynamic and thermal-hydraulic analyses in Cartesian or cylinder coordinates. It is related to the family of COMMIX codes originally developed at Argonne National Laboratory, USA, and particularly to COMMIX-1A and COMMIX-1B, which were made available to FZK in the frame of cooperation contracts within the fast reactor safety field. FLUTAN 2.0 is an improved version of the FLUTAN code released in 1992. It offers some additional innovations, e.g. the QUICK-LECUSSO-FRAM techniques for reducing numerical diffusion in the k-{epsilon} turbulence model equations; a higher sophisticated wall model for specifying a mass flow outside the surface walls together with its flow path and its associated inlet and outlet flow temperatures; and a revised and upgraded pressure boundary condition to fully include the outlet cells in the solution process of the conservation equations. Last but not least, a so-called visualization option based on VISART ...
Differentiating a benign from a malignant lesion by information such as density data, or signal intensities or echo gradients, is not possible with CT, nor MRI, nor ultrasonography. Only some lesions show characteristic signs. Inflammations cannot be difscriminated from malignant tumors. CTs of small tumors in particular are so poor in contrast that it is much more difficult to detect tumors or discriminate them from other lesions, as compared to MR images or ultrasonographs. CT does not detect surface tumors, but is more sensitive than MRI or US in detecting discrete cortical bone lesions. The same applies to small calcified tumors. MRI however is most sensitive in detecting tumor volumes in the yellow marrow, and is the best modality for evaluation of extraossal extension of tumors. CT yields better results than MRI if applied for simultaneous screening of lymph node metastases in the lower neck. MRI frequently is spoilt by movement artefacts. High-resolution, contrast enhanced CT ...
Purpose: With intracranial tumors a flat, contrast-enhancing, probably dural structure adjacent to the tumor can occasionally be observed on gadolinium-DTPA enhanced MR images. Therefore we have attempted to evaluate a tumor infiltration of this enthancement on MRI. Material and Methods: This study included 50 patients. 19 patients had a dural thickening at the tumor base (13 meningiomas and 6 metastases), while 31 patients did not (12 meningiomas and 19 metastases). Studies included plane T{sub 2}-weighted spin echo (SE) images as well as T{sub 1}-weighted axial, coronal, or sagittal plains with and without contrast agent. Histopathological examinations, were done on the tumor base adjacent to the dura mater. Results: 7 of 12 meningiomas showed a meningeal thickening on MRI with histopathologically proven tumor infiltration as did also 5 of 6 metastases. But 3 of 12 meningiomas and 15 of 19 metastases without dural thickening at the tumor base also showed tumor invasion into the dura ...
On behalf of the United Nations Environment Programme (UNEP) a study has been established by the Refrigeration, Air Conditioning and Heat Pump Technical Options Committee in which famous experts of refrigeration technology compiled facts which allow for a reliable prospect of real possibilities of changing from fluorine hydrogen to ozone innoxious substitutes and substitute technologies. With regard to the organization, a division into 6 committees for the establishment of the study has been made: 1. Refrigeration Options Committee, 2. Foams Options Committee, 3. Solvents, Coatings and Adhesives Options Committee, 4. Aerosols, Sterilants and Miscellaneous Uses Options Committee, 5. Halons Technical Options Committee and 6. Economic Options Committee. (BWI).
LP steam turbine retrofits are generally undertaken as a result of mechanical problems, for example due to stress corrosion cracking, torsional vibration or erosion. They present plant operators with an opportunity to introduce advanced aerodynamic technology, and at the same time improve efficiency and availability. Standard components, the majority proven in long-term service, can be used to obtain a permanent solution to the problems. In several European countries, retrofits have been carried out on intact LP steam turbines owned by utilities whose primary motivation is efficiency improvement. (orig.) [Deutsch] Niederdruck-Dampfturbinen werden in der Regel nur dann nachgeruestet, wenn waehrend des Betriebes Probleme durch Spannungsrisskorrosion, Torsionsschwingungen oder Erosion auftreten. In solchen Faellen bietet sich die Gelegenheit, eine moderne aerodynamische Loesung zu waehlen, die gleichzeitig Wirkungsgrad und Verfuegbarkeit verbessert. Es wird gezeigt, dass hierfuer eine ...
In the first part of the symposium, experts reviewed the state of the art of decentralized waste water treatment in Europe. In the second part, exemplary solutions in Poland and the Czech Republic were presented. The final part was dedicated to future concepts and strategies. [German] Im Herbst letzten Jahres hat die Kommunale Umwelt-AktioN U.A.N. in einer Abfolge von drei Abwasserfachsymposien Expertenrunden zum Austausch ueber den aktuellen Stand des Wissens zum Thema dezentrale Abwasserbehandlung veranstaltet. Mit dem Internationalen Symposium 'Konzepte zur Abwasserbehandlung im laendlichen Raum Europas' in Celle hat das Projekt der U.A.N. seinen Abschluss gefunden. Der Konzeption des Projektes entsprechend haben im 1. Teil des Symposiums Experten ueber den Stand der Entwicklung auf dem Sektor der dezentralen Abwasserbehandlung in Deutschland berichtet. Im 2. Teil unserer Fachtagung wurden europaeische Beispiele fuer dezentrale Loesungen aus ...
For the calculation of humidifier systems in supply air systems nomographs and appropriate software are not sufficient alone. System design factors must be considered, also. On the basis of a clear definition interpretation examples are described and remarks for the effective installation of steam distribution systems are given. (orig.) [Deutsch] Es ist nicht zu empfehlen, Befeuchterstrecken bzw. Dampfdiffusionsstrecken ausschliesslich ueber Nomogramme oder ueber eine entsprechende Software auszulegen. Zumindest sollte vorher genauestens geprueft werden, welche Parameter in die Berechnung mit einfliessen. Zur exakten Berechnung der Absorptionsstrecken in Zuluftsystemen muessen auch anlagenspezifische Faktoren beruecksichtigt werden. Die Erfahrung hat jedoch gezeigt, dass dem Begriff `Befeuchterstrecke` zu wenig Aufmerksamkeit gewidmet wird. Hierdurch koennen Fehler entstehen, die nur mit relativ hohem finanziellem Aufwand wieder zu korrigieren sind. Grundsaetzlich ...
The results of the experiments on the pressure oxidation of oil and fat in waste waters shows that the final COD and TOC values decrease with growing temperature and reaction time and decreasing initial concentration. Oxidation of oil and fat in waste water is no straight forward procedure. Therefore it should be compared in the individual case with laternative methods in terms of cost and economic efficiency. (EF) [Deutsch] Die Ergebnisse der Versuche zur Druckoxidation von Oel und Fett in Abwaessern zeigten, dass sich die CSB- und TOC- Endkonzentration verringerte mit steigender Temperatur, Reaktionszeit und verringerter Ausgangskonzentration. Die Oxidierbarkeit von Oel und Fett in Abwaessern ist sehr schwierig. Deshalb sollte in jedem Einzelfall ein Vergleich mit alternativen Verfahren bezueglich Aufwand und Wirtschaftlichkeit vorgenommen werden. (EF)
We develop a general framework for the formulation of the action principle and the noether theorem for classical noncommutative field theories. We give a concrete example of an algebra that fits into this framework. It describes a scalar field theory on noncommutative minkowski space. We develop a notion of locality for this algebra and investigate the locality properties of localised interaction terms. This leads us to the definition of local functionals on the field algebra. We propose a scheme for the quantisation of these functionals. (orig.) [German] Wir entwickeln eine allgemeinen rahmen, der es erlaubt, das wirkungsprinzip und das noether-theorem fuer klassische nichtkommutative feldtheorien zu formulieren. Als ein konkretes beispiel betrachten wir eine algebra, die sich in diesem rahmen einfuegt, und die eine skalare feldtheorie auf dem nichtkommutativen minkowski-raum beschreibt. Fuer diese algebra wird ein lokalitaetsbegriff entwickelt und untersucht, welche ...
In the last two years, the VDMA work group 'Functional security' compiled a qualitative and quantitative procedure for the determination and evaluation of turbo-machine specific risks. With the calibrated risk graph for turbo-machines the requirements (Safety Integrity Level SIL) to the protective functions for turbo-machines (steam turbines, gas turbines, generators and compressors) were determined. With consideration of the legislation, the work group compiled a recommendation for the renewal and/or reconstruction of protective functions with old facilities.
A report is given of investigations into the possibility of utilizing red mud from the Bayer process for producing Ferrari cements. On repeated burning at 1450deg C suitable mixtures of red mud with silica and lime form a clinker with a low free lime content from which Ferrari cement can be produced. The average 28-day compressive strengths of cements produced from this clinker are so encouraging that further investigations are appropriate. (orig.).
A manipulator for checking the inside of a vertical, flange-shaped collector of a horizontal steam generator consists of a rotating mast with bearings at the top and bottom ends with a support that can be moved along the length of the mast for the checking system mountings. The support is propelled by a drive spindle placed parallel to the mast with its drive head bearing in the support and locked into a toothed rack attached to the mast. The checking system mountings are fitted in or on the walls of the support and are very close to the box-shaped support. Their retractable arms are hinged.
FLUTAN is a highly vectorized computer code for 3-D fluiddynamic and thermal-hydraulic analyses in cartesian and cylinder coordinates. It is related to the family of COMMIX codes originally developed at Argonne National Laboratory, USA. To a large extent, FLUTAN relies on basic concepts and structures imported from COMMIX-1B and COMMIX-2 which were made available to KfK in the frame of cooperation contracts in the fast reactor safety field. While on the one hand not all features of the original COMMIX versions have been implemented in FLUTAN, the code on the other hand includes some essential innovative options like CRESOR solution algorithm, general 3-dimensional rebalacing scheme for solving the pressure equation, and LECUSSO-QUICK-FRAM techniques suitable for reducing `numerical diffusion` in both the enthalphy and momentum equations. This report provides users with detailed input instructions, presents formulations of the various model options, and explains by means of ...
Progress reports on the European Research Centre for Air Pollution Control Measures project are presented. Topics covered were: assessment and analysis of the impacts of airborne pollutants on forest trees, and distinction from other potential causes of recent forest dieback; research into atmospheric dispersion, conversion and deposition of airborne pollutants; development and optimization of industrial technical processes to reduce or avoid emissions; and providing instruments and making recommendations to the industrial and political sectors.
In order to improve the capacity and service life of cathodes, the effect of carboxy-methyl cellulose, soot, silica gel and fibres was examined. Structural tests and electrical and electro-chemical measurements are used for this. The additives can affect crystallization in the manufacturing stage of the electrodes and can increase the storage capacity for water and the electronic conductivity. They act to stabilize the mass in cyclic operation. Soot additive has little effect on the properties of the electrode, but the other substances increase the service life or the use of the mass. (LU).
In recent years very good experience has been accumulated with self-supporting low-pressure blades. Today blades are constructed up to a length of 1060 mm (50 Hz) or 1360 mm (25 Hz). In this process modern computational methods from aerodynamics and also from mechanics are employed. The further development of computer technology also permits new methods, for example the use of curved fixed blading as well as the optimization of existing designs. (orig.).
In the presented case study CRS processing was able to improve the overall data quality of the processed lines in terms of signal-to-noise ratio and imaging. The complex geology is causing serious problems in conventional NMO/DMO processing that were solved by CRS processing. Even a depth processing with velocities calculated from CRS attributes gives good results similar to those from PreSDM in terms of the velocity field. Data quality of poststack depth migrated CRS stacks is even better than the image from PreSDM. (orig.)
The first biogas plant using the Plauen method has been operated without failures in the Saxon Vogtland since May 1987. This large scale anaerob treatment plant which is the first one in Germany handles besides agricultural recidual substance both municipal and industrial organic residues. The results show clearly that fermentation is a real alternative to composting, combusting and deponing. (orig.)
We reported three cases of acute intracranial tuberculosis including miliary tuberculosis, basal meningitis, tuberculomas and neuritis of cranial nerves. All patients had native and contrast enhanced CT and MRI scans. MRI revealed more granulomas and a better imaging contrast in the detection of basal meningitis. Neuritis was diagnosed only with the MRI. MRI scans should be prefered as the imaging procedure in clinically presumed intracranial tuberculosis. (orig.) [Deutsch] Die Befunde von drei Patienten mit intrakranieller Tuberkulose (intrakranielle Miliartuberkulose, Meningitis tuberculosa, Neuritis und Tuberkulome) in der Magnetresonanztomographie (MRT) wurden mit der Computertomographie (CT) verglichen. Sowohl die MRT als auch die CT wurden nativ und nach Kontrastmittelgabe durchgefuehrt. Die MRT zeigte sich im Nachweis von Granulomen insbesondere im Bereich des Hirnstamms ueberlegen. Ebenso wurde ein hoeherer Bildkontrast bei der Darstellung der Meningitis ...
A team at the Paul Scherrer Institute (PSI) recently achieved a breakthrough in the development of an environment-friendly and rechargeable battery with novel electrodes. The energy storage density of a rechargeable 12 V/20 Ah zinc/air battery could be increased to 100 watt hours per kilogramme - three times as much as conventional lead accumulators. 20-Ah cells could be charged and discharged 55 times in 1000 hours without any loss of capacity worth mentioning. This is a remarkable cycle stability. (orig.) [German] Einem Team des Paul Scherrer Instituts (PSI) ist kuerzlich bei der Entwicklung einer umweltfreundlichen und wiederaufladbaren Batterie mit neuartigen Elektroden der Durchbruch gelungen. Dabei konnte die Energiespeicherdichte einer wiederaufladbaren 12 V/20 Ah-Zink-Luft-Batterie auf 100 Wattstunden pro Kilogramm gesteigert werden - dreimal soviel wie bei konventionellen Bleiakkumulatoren. 20-Ah-Zellen konnten in 1000 Stunden ohne ...
Zone modeling permits taking account of the effect of load-relieving air conduction systems in the planning of HVAC plants. Although this only supplies average values for the degree of load and height of the fresh air layer rather than a detailed description of concentration and temperature distributions in the room, it is quite sufficient for the planning of load-relieving air conduction systems. Moreover, the cost of zone modeling in the planning of HVAC plants remains within reasonable limits. Upscale planning, instruments can thus be reserved for more exacting problems. (orig.) [Deutsch] Zonenmodelle erlauben die Wirkung lastmindernder Luftfuehrungen bei der Planung von RLT-Anlagen zu beruecksichtigen. Sie liefern zwar nur Mittelwerte fuer den Belastungsgrad und die Hoehe der Zuluftschicht und keine detaillierte Konzentrations- und Temperaturverteilungen im Raum. Diese Werte reichen jedoch fuer die Planung lastmindernder Luftfuehrungskonzepte aus. Zudem ist der ...
This richly illustrated toolbook and atlas contains information on all aspects of nmr diagnostic imaging of benign or malignant neoplasms of female and male mammary glands. It offers pinpointed guidance and insight for vocational training and continuing training of radiology assistants, students and medical radiologists. (orig./AJ) [German] Die MRT als hochaufloesendes und schaedigungsfreies Diagnostikum gewinnt gerade in der emotional stark besetzten Mammadiagnostik zunehmend an Bedeutung. Dennoch beherrschen nur wenige Zentren im deutschsprachigen Raum diese Technik, die - eine hohe Reproduzierbarkeit bei fehlender Belastung fuer die Patientin bietet, - invasive Karzinome bereits ab einer Groesse von 5 mm mit hoher Zuverlaessigkeit ausschliessen kann und - gerade bei widerspruechlichen Befunden zwischen klinischer Untersuchung, Roentgenmammographie und perkutaner Biopsie eine wesentliche Entscheidungshilfe bieten kann. Aus einem der ...
Internal combustion engines with mechanically driven superchargers are known for good performance at low engine speeds and fast response times under fluctuating loads. Application engineers can choose between superchargers with and without internal compression - the familiar roots (blower) type or true compressors - for supercharging an internal combustion engine. This article by DaimlerChrysler describes two options for improving the partial load behaviour of mechanically supercharged internal combustion engines with compressors. (orig.) [German] Die Aufladung mit mechanisch angetriebenen Verdraengerladern zeichnet sich durch guten Druckaufbau bei niedrigen Drehzahlen und gute Dynamik bei Lastwechseln aus. Fuer die Applikation am Verbrennungsmotor koennen Maschinen ohne innere Verdichtung - wie die bekannten Roots-Geblaese - oder Maschinen mit innerer Verdichtung - Kompressoren im eigentlichen Sinne - zum Einsatz kommen. In diesem Beitrag von ...
Two of the working sessions of the meeting were devoted to aspects of international atomic energy law; the international character of the meeting was also reflected by the home countries of the members of the panel discussion concluding the working sessions. There was substantial reason to put emphasis on the international dimension of the topics discussed. In June 1994, the Nuclear Safety Convention had been signed in Vienna by diplomatic representatives of the signatory countries, and this Convention marks a signpost in the history of international atomic energy law. At the time the meeting was held, negotiations for improving the international nuclear lability law, which had been dragging on since 1989, had come to a stalemate. The meeting offered a suitable forum for taking a scientific approach to tackle the complex problems involved in reshaping the law on nuclear safety and nuclear liability. The third working session of the meeting has been discussing topics relating to the ...
For millions of people general noise and especially traffic noise are the main sources of environmental pollution. The increasingly stricter noise pollution abatement limiting values laid down by the law call for motor vehicle noise pollution abatement measures. Within the framework of today`s cost- and performance-oriented automobile and engine development developing engineers are required to reduce noise levels. The present state of the art is described and future possibilities of combustion engine structure-borne noise calculation and optimization are discussed from the point of view of K + P Computerunterstuetzte Strukturanalysen GmbH. (orig.) [Deutsch] Laerm allgemein und dabei speziell wiederum der Verkehrslaerm steht fuer Millionen von Menschen an allererster Stelle der persoenlichen Belastung durch die Umwelt. Zur Minderung der Laermbelastung werden vom Gesetzgeber immer schaerfere Grenzwerte vorgeschrieben, die dazu zwingen, Massnahmen ...
Ventilation systems must ensure high room air quality with minimum energy consumption in all states of operation. Systems for ventilation on demand are increasing their market share. (orig./MSK) [Deutsch] Oberste Aufgabe von Raumlufttechnischen Anlagen ist die Sicherstellung guter Raumluftqualitaet bei minimalem Energieverbrauch unter allen Betriebsbedingungen. Um dieses Ziel zu erreichen, setzt sich am Markt zunehmend die bedarfsgeregelte Lueftung durch. (orig./MSK)
Shell Solar GmbH is working on a variant of the so-called stacked elemental layer process for CIGSSe absorber production. The metal films resp. the selenium are deposited on the Mb electrode at room temperature by DC sputtering (CIG) or evaporation (Se) and then processed into semiconductors by rapid thermal annealing (RTP). Currently, the mean efficiency of the pilot plant is i 12.6 {+-} 0.2 % for non-sealed 30 x 30 cm{sup 2} modules, the key efficiency is 13.0 %. In addition to the 30 x 30 cm{sup 2} pilot line, a small series of 60x90cm2 modules was constructed in December 2004. Here, the mean efficiency was 13.0 percent while the average module power was higher than 60 W. The contribution also describes investigations of ceramically sputtered n-ZnO:Al layers with reduced Al concedntrations of 1 percent and on reactively sputtered n-ZnO.Al layers from the double roller magnetron. (orig.) [German] Bei Shell Solar GmbH wird eine Variante des sogenannten ...
This short article discusses the results of a market survey on ventilation systems for residential buildings and the role played by ventilation systems in our daily lives. Problems incurred as a result of insufficient ventilation conditions such as the formation of mould in dwellings whose windows have been replaced with better seals are discussed, for example. The negative image of air-conditioning and its causes are examined. The need for action in this area is stressed. Further findings of the study are presented, including a detailed review of current equipment and scenarios on how these systems can develop in the future. The extension of the study to cover the situation in further European countries is mentioned.
In order to ensure a power balance in an electrical network a spinning reserve has to be capable of activation within seconds. However, because of the need to vary the fuel flow in the steam generator, the run-up of output takes minutes. The required capacity response is therefore achieved by storage of steam from the steam generator. In this process the turbine control valves come into action in a specific manner. The paper describes the importance of the initial reserve for unit capacity control. (orig.).
The amended Radiation Protection Ordinance of 2001 contains regulations on natural radioactive materials, whose recycling or disposal poses practical problems. There is little experience in this field so far. [German] Die novellierte Strahlenschutzverordnung von 2001 befasst sich auch mit natuerlich vorkommenden radioaktiven Stoffen. Bei ihrer Verwertung oder Beseitigung ergeben sich praktische Fragen, die beachtet werden muessen. Erfahrungen auf diesem Gebiet liegen bisher kaum vor. (orig.)
The report covers the results of exposing materials for steam turbines to increased steam temperatures in two modules of the KOMET 650 testing facility at the Westfalen power plant. Ferritic/martensitic steels with 9 to 12% Cr and austenite and nickel-based alloys were investigated. Some experimental coatings on low-alloy Cr steel were also tested. The principal findings are presented. It will become possible to construct advanced power stations to be operated at higher temperatures. (orig.)
The influences of temperature and duration of tempering on hardness and microstructure were investigated at high-temperature martensitic and low-carbon steels with 9% chrome and the further alloying elements molybdenium, vanadium, niobium and partially tungsten. After austenitizing and subsequent air cooling the steels were tempered at temperatures below, at and above Ac{sub 1b} for different times and finally a hardness test was performed. Making use of the temperature dependence of the hardness tempering diagrams were constructed and the Hollomon-Jaffe-Parameter on the three steels was determined within its application limits. Micrographs of the structure shows the formation of the carbides and the martensite. At tempering temperatures below Ac{sub 1b} a decrease of hardness occurs, above Ac{sub 1b}, a hardness rise due to the partial austenitizing was obtained. While hardening below Ac{sub 1b}, the tempering quality increases from P 91, NF 616 to E 911. (orig.) [Deutsch] An ...
Purpose: In vitro evaluation of possible deflection and heating of present-day prosthetic heart valves, 12 technical and 5 biological, were investigated using a 1.5 Tesla Siemens Vision system. Deflection was measured at the edge of a 1.5 Tesla superconducting magnet. Each valve was then submerged in a vial of a 1/1 electrolyte solution and temperature was measured before and after imaging with a turbo-spin-echo sequence (TR 5200 ms, TE 138 ms, Flip angle 180 C, acquisition time 10.5 minutes, length of echo train 29). MR imaging was performed with phase encoding parallel and perpendicular to the plane of the valves. Results: None of the investigated prosthetic heart valves was deflected. The maximal observed temperature rise was 0.5 C. During MR investigation of the prostheses, artifacts caused by metallic parts were less evident using a spin-echo sequence than a gradient-echo sequence. Conclusions: Patients with the tested present-day prosthetic heart valves can be safely imaged by ...
The study examines the isothermal fatigue properties of novel ODS iron-base or nickel-base superalloys at temperatures of 850 C and 1050 C. The materials are different in grain structure and texture, so that particularly the effects of grain structures and textures can be studied. In order to also perform examinations of creep-fatigue interactions, various load cycles are applied. It is shown that the LCF-affected life of the grain structures of both alloy types is determined by the elastic modulus. The cyclic lifetimes determined by the conventional Manson-Coffin method for both alloy types exhibit differences of up to two orders of magnitude. Using the product of the total strain range and the elastic modulus, however, will yield precise life predictions. Under conditions of LCF stress only, the grain structure has no effect on the materials` service life, other than in the case of creep-fatigue, but the grain structure has a decisive influence on the damage mechanisms and the course ...
With increasing liberalization of the energy sector, German suppliers of line-transmitted energy find themselves in an utterly changed sales environment, forcing companies and utilities to elaborate for the first time management policies and strategies that will ensure loyalty of their present customers, and help to solicit new customers. The article here explains some major terms and instruments used in designing key-account management strategies, as well as general procedures for suitability assessment. (orig/CB)
A novel zinc-air battery might soon enhance the mileage and applications of electric vehicles. The battery named Zoxy battery weighs 80% less than a conventional lead battery, but has an equal amount of energy in store. (orig./CB) [Deutsch] Eine neuartige Zink-Luft-Batterie koennte vor allem dem Elektroauto groessere Reichweiten und neue Einsatzmoeglichkeiten erschliessen. Die sogenannte Zoxy-Batterie ist 80% leichter als eine herkoemmliche Bleibatterie - bei gleichem Energiegehalt. (orig.)
The book is intended as a source of information for general practioners and for medical students doing their practical training. Efficient application of imaging methods is explained with great emphasis on practical aspects, concentrating on typical tasks to be solved for adult patients with internal disease or surgical problems. The material is arranged by various organic systems of the body. Graded diagnostics for a stepwise approach to the final diagnosis is the concept described, and is shown to be of advantage to the patient and in terms of cost and time.
We performed a comparative study of digitally and conventionally acquired images in gastrointestinal examinations. Radiation dose and spatial resolution were determined in a water phantom. In 676 examinations with either conventional or digital imaging (system: Diagnost 76, DSI) the number of images and the duration of the fluoroscopy time were compared. 101 examinations with digital as well as conventional documentation were evaluated by using 5 criteria describing the diagnostic performance. The entrance dose of the DSI is 12% to 36% of the film/screen system and the spatial resolution of the DSI may be better than that of a film/screen system with a speed of 200. The fluoroscopy time shows no significant difference between DSI and the film/screen technique. In 2 of 4 examination modes significantly more images were produced by the DSI. With exception of the criterion of edge sharpness, DSI yields a significantly inferior assessment compared with the film/screen technique. (orig./MG) ...
A new generation of lead alloys for making lead batteries is being introduced in highly developed countries. A very important characteristic of these alloys is the presence of Ca, Al and Sn. Such alloys have the property of stabilizing the amount of gas emitted as a result of the decomposition of the electrolyte on the level of pure lead i.e. significantly smaller than lead alloys containing Se e.g. PbSb 1.7Se. Such alloys have not been produced in Poland so far. - In this paper we are presenting the method and equipment used to produce a pilot portion of PbSnCaAl alloy (mass approximately 80 Mg) on an industrial scale at HMN ''Szopienice'' S.A. lead refinery. We also present the results of the tests regarding the chemical homogeneity of the alloy produced, as well as its structural and casting properties. On the basis of the tests conducted it has been found that the method is industrially adequate and as such it has been introduced into the ...
The corrosion behavior of steel in water from certain oil fields with various organic inhibitors was studied by applying potentiodynamic technique at pH 5.9. The inhibitors which were used include 2-methylbenzimidazole (I), 2-mercaptobenzimidazole (II), 2-mercapto-5-methylbenzimidazole (III), and 2-mercaptothiazole (IV). The inhibiting efficiency of the different additives was evaluated from their anodic and cathodic polarization curves at different temperatures. A comparative study of curve fitting procedures using the kinetic thermodynamic model and those utilizing well-known adsorption isotherms was undertaken. Three types of isotherms were used, Langmuir, Frumkin and Flory-Huggins isotherm. The results show that the kinetic-thermodynamic model and Flory-Huggins isotherms are more suitable to fit the data for the four inhibitors, at all applied temperatures. From the values of binding constants, K, the order of inhibitor efficiency is: III > IV > II > I and thus ...
There are many applications that necessitate reliable and permanent power supply, e.g. power stations, airports, computer centers or hospitals. The stationary battery systems must be monitored by efficient systems, e.g. Batlog. (orig.) [Deutsch] Viele Anwendungen verlangen eine permanent verfuegbare und zuverlaessige Stromversorgung. Kraftwerke, Flughaefen, Rechenzentren oder Krankenhaeuser muessen ihre Prozesse auch bei einem Netzausfall oder einer Versorgungsunterbrechung weiterbetreiben. Dies gelingt nur, wenn sich der entsprechende Energiespeicher in einsatzbereitem Zustand befindet. Die Ueberwachung der stationaeren Batterieanlagen erfordert leistungsfaehige Systeme wie Batlog. (orig.)
Technical innovations such as the availability of movable patient platforms and the introduction of 32-channel systems have made whole-body MRI for tumor staging feasible. In addition, the development of dual-modality PET/CT systems offers the opportunity to perform anatometabolic tumor staging with whole-body coverage in a single session. Based on an increase in patient survival when applying a stage-adapted therapy in different malignant diseases the relevant question relates to the accuracies of whole-body MRI and whole-body PET/CT for TNM staging. This review article addresses whole-body tumor staging with MRI and FDG-PET/CT with special emphasis on diagnostic accuracies for staging different malignant diseases. (orig.) [German] Technische Neuerungen, wie die Verfuegbarkeit beweglicher Tischaufsaetze oder die Einfuehrung von 32-Kanal-Systemen, haben die Ganzkoerperbildgebung mit der MRT ermoeglicht. Die Entwicklung kombinierter PET/CT-Systeme bereitet den Weg fuer eine simultane ...
It is necessary to measure strength and creep behavior to guarantee the safe and reliable usage of refractory alloys at extremely high temperatures. In the literature there is very little information available about the properties of Mo-Re alloys at temperatures higher than 1000 C. A special test facility has been designed and built for stress-rupture testing at very high temperatures (up to 3000 C) of refractory metals and alloys in inert atmospheres. - The stress-rupture strength as well as the creep behavior of molybdenum-rhenium alloys with rhenium contents between 41 and 51 wt.% have been determined at temperatures ranging from 1200 to 2000 C, and rupture times of up to 10 hours using this facility. Previous measurements of stress-rupture strength and creep behavior of pure rhenium have been compared with the measurement results of Mo-Re alloys. - The discussion of the values measured is based on metallographic test results and scanning electron microscopy (SEM) images of Mo-Re ...
Within its competence for energy research, the Bundesministerium fuer Wirtschaft und Arbeit (BMWA) (Federal Ministry of Economics and Technology) sponsors investigations into the safety of nuclear power plants. The objective of these investigations is to provide fundamental knowledge, procedures and methods to contribute to realistic safety assessments of nuclear installations, to the further development of safety technology and to make use of the potential of innovative safety-related approaches. The Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, by order to the BMWi, continuously issues information on the status of such investigations by publishing semi-annual and annual progress reports within the series of GRS-F-Fortschrittsberichte (GRS-F-Progress Reports). Each progress report represents a compilation of individual reports about the objectives, work performed, results achieved, next steps of the work etc. The individual reports are prepared in a standard form by the ...
Austenitic stainless steel (18% Cr, 12% Ni, Mo gradation between 0,06 to 3,6%) had been solution nitrided. By step-by-step removing, the samples could be prepared with various surface contents of nitrogen from 0.04 to 0.42%. In two test series the influence of nitrogen had been determined. The susceptibility against pitting corrosion of these samples had been tested by the chronopotentiostatical method. For the investigated steel composition and the used corrosion system there is no influence of molybdenum on the effectiveness of nitrogen. The effectiveness of nitrogen can be described by the factor 25 in the PRE. By the investigation of the surfaces with the XPS analysis, it could be shown that the passivation and the pit nucleation is influenced by nitrogen. In these ranges NO{sub x}, NH{sub x}, and NH{sub z}-spectra have been detected. Bound Mo was found in steels containing molybdenum. It is assumed that the repassivation mechanisms of N and Mo work independently of each other. ...
The report describes the processing of TiSi{sub 2}, MoSi{sub 2} and Ti{sub 5}Si{sub 3} by means of metal injection molding (MIM). First, the sintering activities of the three materials were investigated. After this, the viscosities of different mixtures of organic binder and powders of the three materials were determined, and in the final stage, components were produced by injection molding, the binder was removed, and the components were sintered. TiSi{sub 2} in powder form could be sintered to more than 95% of its theoretical density after 4 h at 1386 C. Metallographic analyses proved leaktightness of the component at this density. In the case of Ti{sub 5}Si{sub 3}, it was found that this material requires very long sintering times and high sintering temperatures for sintering to about 94% of its theoretical density. Metallographic analyses showed that only about 90% of the theoretical density was reached. MoSi{sub 2} in powder form could be sintered to only 90% of its theoretical ...
Methods: Systemic irradiation of neuroaxis is an essential part in the management of medulloblastoma, stPNET and intracranial germ cell tumors. The introduction of quality assurance programs in radiooncology assures a precise radiotherapy of target volumes and is a prerequisite to improve survival. Results: Hyperfractionated radiotherapy has the potential of increasing dose to tumor more safely without increasing the risk for late adverse effects. Pilot studies revealed excellent tumor control in medulloblastoma with acceptable acute toxicity and a long-term survival of up to 96%. In medulloblastoma stereotactic radiation techniques reveal an acceptable toxicity and promising results in tumor control in recurrent disease or as primary treatment. They are now part of future treatment protocols in case of persisting residual tumor. Radiotherapy alone in pure germinoma is continuously yielding high cure rates. In secreting germ cell tumors cisplatin containing chemotherapies in ...
In the year 1996 the spheres of competence of several DLR-Institutes working in the areas of fluid dynamics, reaction kinetics, combustion, numerical methods and laser measuring techniques have been brought together while contributing to the internal DLR project 'combustion chamber modelling (BKM)', in order to proceed with the computational simulation of combustion processes in combustion chambers of gas turbines. The main issue was the development of a research code for numerical simulation of fluid flow in real combustion chambers. Here the development of computational models of physical and chemical processes was emphasized, among other processes the formation of soot was treated. Moreover, a worldwide outstanding database of measured data for the purpose of code validation has been created within the framework of the BKM project using the laboratory facilities of the DLR, which are in Germany unique for the experimental investigation of the various processes in ...
The thermochemical calculations performed with a large number of elements to describe the chemical system in a Phebus FP test allow the following conclusions: The metallic absorber materials play a significant role in fission product speciation. At around 1000 C and above, silver iodide is the dominant iodine carrier in a full steam atmosphere in both FPT0 and FPT1. At lower temperatures, cadmium iodide takes over. In a reduced environment, indium iodide becomes important. Caesium iodide does certainly appear; at certain test conditions it becomes the major iodine transporting vehicle. But its role is not greater than that of the other iodides. It has more chances in FPT1 than in FPT0. Chlorine, which was present in FPT0 as a contaminant in relatively large amounts, does not prevent the iodine from forming Csl. Both share the caesium like partners. The evolution of caesium chloride and iodide proceeds in parallel. When CsCl is abundant, Csl is strong, too. Should boron be added to the ...
The establishment of the domestic market in Europe requires rules for the assignment of orders, with which a standardization of the rules of competition can be achieved and with which a discrimination of individual bidders can be prevented. Clients and contractors of power station equipments equally are affected by the definitions for the assignment of orders. The contribution under consideration is a regulation for the procurement of steam turbine systems. It is a supplement of the European standard DIN EN 45510:1998. The regulation integrates the former terms of delivery of association of the electricity industry (VDEW) for steam turbines as well as the collection and evaluation of a multiplicity of experiences of the VGB regulations.
The economic development of eastern Europe was associated during the last 15 years with the following average annual increases in energy consumption: Approximately 1% in the sectors industry, building and transport, almost 7% in the farming sector, approximately 3% in households, and nearly 4% in the municipal sector. This trend will not continue. As the economic system shifts from centrally planned to free economy and as the previously secluded economy is forced to face world market conditions as well as changed pars of exchange and conditions of payment, it not only experiences a transitory, sharp dip of economic growth in general but, in particular, drastic structural changes. - While there is to be expected, on the whole a slump in national economic growth, in tradiational branches of industry (e.g., metallurgy, the chemicals and textile industry) as well as in farming, such sectors as the service industry and small trade are expanding. (orig./UA).
So far, publications in turbomachinery engineering have tended to neglect the description of control systems and strategies which could be converted into practical guidelines for turbine operation. The contribution describes the power station turbine as a basis for modelling the control stage. The solutions will serve as a basis for further type-specific investigations of the problem. [German] Eine vornehmlich regelungstechnisch ausgerichtete Beschreibung des thermodynamisch-mechanischen Wirkungsgeschehens im Bereich der Regelstufe von Dampfturbinen sowie deren Umsetzung in schluessige, betriebsrelevante Aussagen fehlen bislang in der Turbomaschinenliteratur. Im Beitrag werden am Beispiel der Kraftwerksturbine die Grundlagen fuer eine modelltechnische Nachbildung der Regelstufe entwickelt. Die Loesungen dienen als Ausgangsbasis fuer weitere typenspezifische Bearbeitungen dieses Problems. (orig.)
Liberalization and the associated necessity of providing, where possible, inexpensive electrical energy, has intensified still further the demand for higher efficiency steam turbines. Accordingly, continuous efforts are being taken to improve all the flow guiding components of a steam turbine. Special attention is given here to the blading. (orig.) [Deutsch] Die Liberalisierung und die damit verbundene Notwendigkeit, elektrische Energie moeglichst preisguenstig zur Verfuegung zu stellen, hat die Forderung nach hohen Wirkungsgraden von Dampfturbinen weiter verschaerft. Es werden daher kontinuierlich Anstrengungen unternommen, alle stroemungsfuehrenden Teile einer Dampfturbine zu verbessern. Das Hauptaugenmerk gilt dabei der Beschaufelung. (orig.)
Facility management has long been regarded as a cost reduction measure, but it is also a means of raising the financial worth of a building so that landlords can get higher rents or sell the building at a better price. [German] Lange Zeit wurde Facility Management als eine Massnahme zur Kostensenkung angesehen. Heutzutage zeigt sich immer mehr, dass das Facility Management sehr viel umfassender zu verstehen ist: Der Wert eines Gebaeudes bemisst sich nicht allein an einer niedrigen Kostenquote, sondern er soll umfassend Investoren wie Mietern den hoechst moeglichen Nutzen bringen. Nicht allein der kostenguenstige Betrieb ist entscheidend, sondern der Wert des Gebaeudes muss insgesamt gesteigert werden. (orig.)
After cooling ceilings and source ventilation, simple air conditioning systems like thermal activation of concrete cores are gaining general acceptance. Parallel to this, ground source cooling systems are reducing the need for cold generation. Air conditioning systems of this type are favoured by producers of floor heating systems looking for a new market segment. [German] Nach Kuehldecken und Quellueftung gewinnen jetzt einfach aufgebaute Raumklimaanlagen, wie die thermische Betonkernaktivierung, immer mehr Anhaenger. Parallel dazu werden Verfahren zur Erdkaeltenutzung entwickelt, die den Anteil kuenstlich erzeugter Kaelte weiter zurueckdraengen. Forciert wird diese Art der Klimatisierung insbesondere durch die Hersteller von Fussbodenheizungen, fuer die sich hier ein neues Marktsegment eroeffnet. (orig.)
MPA research activities focus on fracture prevention and on the development of a generally applicable method of component integrity testing which, independent of the safety relevance of the components involved, is also part of ageing management. (orig.) [German] Die Forschungsaktivitaeten an der MPA im Hinblick auf die Erhoehung der Sicherheit und Zuverlaessigkeit komplex beanspruchter Bauteile orientieren sich an den Grundgedanken des Basissicherheitskonzepts (Prinzip des Bruchausschlusses). Zielsetzung war dabei die Entwicklung eines allgemein anwendbaren Nachweisverfahrens zur Komponentenintegritaet, das, abhaengig von der sicherheitstechnischen Relevanz der zu betrachtenden Komponenten, auch Bestandteil des Alterungsmanagements ist. (orig.)
Abstract Plant pathogenic bacteria of the genus Xanthomonas cause a variety of diseases in economically important monocotyledonous and dicotyledonous crop plants worldwide. Successful infection and bacterial multiplication in the host tissue often depend on the virulence factors secreted including adhesins, polysaccharides, LPS and degradative enzymes. One of the key pathogenicity factors is the type III secretion system, which injects effector proteins into the host cell cytosol to manipulate plant cellular processes such as basal defense to the benefit of the pathogen. The coordinated expression of bacterial virulence factors is orchestrated by quorum-sensing pathways, multiple two-component systems and transcriptional regulators such as Clp, Zur, FhrR, HrpX and HpaR. Furthermore, virule...
Calcium sulfate dihydrate which is co-produced in the scrubbing of waste gases from bituminous coal power plants is employed in the underground road securing after recrystallization. Beta-sulfate semi hydrate is obtained from the dihydrate by recrystallisation and it is used as such or as a stiff mixture with additives as a stowing material. Particularly fly ash from coal combustion units, washery refuses and development rocks from coal mining or slags from the metallurgical industry can be used as additives. The compressive and the bending tensile strength of the stowing material can be adjusted by the water content in case beta sulfate semihydrate is used as such.
This process for the preparation of nonaqueous dispersions of water-soluble polymerisates concerns compounds obtained by polymerization of water-soluble unsaturated ethylenic monomers in an emulsion of water in oil. The product is then dewatered to a maximum residual water content of 5% by means of microwaves. The process is azeotropic. The polymer has a molecular weight between 100,000 and 50,000,000, preferably between one and 10 million. Before treating with microwaves, the mixture is concentrated by conventional means until it has a polymer concentration between 20 and 65%, preferably between 40 and 60%. The microwaves have a wavelength between 0.1 and 30 cm. These polymer dispersions can be used in drilling fluids and as additives in tertiary oil recovery. 4 claims.
This is a process for manufacturing a semi-rigid, folding solar generator manufactured from several coated solar cells (Cics), which has at least two folding parts connected together so as to turn by hinges, characterized by the following stages of the process: a) On the back of matrix subsections, in order to cover the connector, carbon fibre strips are glued on, which project over the upper or lower edge of each matrix subsection. b) The projecting ends of adjacent carbon fiber strips are connected with two carbon fibre strips. c) At least two matrix subsections are fixed in separately manufactured carbon fiber frames, and d) the carbon fiber frames, together with the matrix subsections are connected via hinges to a solar generator.
This is a process for producing calcium sulfate dihydrate during desulfurization of stack gases from power station boilers, where the stack gases are introduced into a washing tower and are treated with a washing water suspension containing lime in the washing tower, where oxygen in the form of air or of air enriched in oxygen is also blown into the washing tower, and where the washing water suspension drawn off from the washing tower is fed back to the washing tower at a temperature of 45 to 50/sup 0/C in the circuit and at least part of the flow goes via a thickener and where calcium sulfate dihydrate slurry is drawn off from the thickener.
The dogmatic and constitutional basis as well as points of definition concerning the Technical Code Clean Air (TA Luft) are explained at first, followed by an assessment of the air pollution concentrations within the overall complex of the air pollution abatement measures, and an analyses of air pollution concentrations as a concretization of the state-of-the-art. In connection with the differentiation of the various applicability levels of TA Luft, the inhouse validy for authorities, the importance for law courts and, finally, the external binding effect for plant operators and possible third parties are discussed. At the center of attention are questions concerning validity claims and validity possibilities. (HSCH).
Better quality of thermal comfort as well as reduced heat energy demand and accordingly CO{sub 2} emission can be achieved by better heating and ventilation strategies in private buildings. The paper deals with a novel model-based measurement and automation system. It describes the implementation of better strategies under given technical circumstances. (orig.) [German] Durch Verbesserung der Heizungs- und Lueftungsstrategien im privaten Lebensbereich kann sowohl Heizenergie eingespart und damit die CO{sub 2}-Emission verringert, als auch die Raumbehaglichkeit verbessert werden. Der Beitrag behandelt ein modellgestuetztes Mess- und Automatisierungssystem, mit dem die Realisierung der verbesserten Strategien unter gegebenen technischen Randbedingungen praktisch erst moeglich wird. (orig.)
Elektrochemische Potentialmessungen (auch Potentialfeldmessungen) haben sich seit Jahren bewahrt, Bereiche mit aktiver chloridinduzierter Korrosion an tausalzexponierten Bauwerken, wie z. B. Bruckentafeln sowie Zwischendecks und Bodenplatten von Parkhausern und Tiefgaragen nachzuweisen. Bereits 1990 erschien die erste Fassung des Merkblatts B3 der DGZfP. Das DAfStb Heft 422 (1991) - Prufung von Beton Empfehlungen und Hinweise zu DIN 1048 - enthielt die Potentialfeldmessung bzw. das Merkblatt B3 im Anhang. In Deutschland liegen somit zwei Jahrzehnte Erfahrungen mit den entsprechenden Regelwerken und naturlich auch in der praktischen Anwendung vor. In der Praxis zeigte sich jedoch auch, dass die Anwendung verbessert werden muss. Die Potentialmessung wurde vielfach sogar falsch durchgefuhrt, ...
The first part of the study goes into the determination of efficient strategies for the reduction of air pollutants. The developed method is not only derived theoretically but is tested with the concrete example of emissions sources of a German state. The second part goes into the question what the government can do in order to attain that air pollution abatement measures recognized as being efficient will be put into practice. As market economy mechanisms have advantages over central state planning in the allocation of economic resources the question arises if not also for environmental protection market economy tools may contribute to an improvement of the efficiency of air pollution abatement. Therefore the suitability of different tools of environmental policy for the realization of efficient air pollution abatement is investigated and evaluated. This is again not done abstractly but with existing emission sources. (orig./HSCH). 32 figs., 12 tabs.
The program introduced here for determining and describing the multi-axial creep of pipes is based, on the one hand, on the results of the nuclear process heat prototype plant material program and, on the other hand, on the possible load conditions which arise for evaluating accidents or extreme working situations. The basis of a theoretical description of multi-axial creep is the invariant theory in which both the von Mises configuration change hypothesis and the Norton creep law are included. Combined tension and torsion are also considered in detail, the superimposition of cyclic stresses in the tensile threshold area is discussed and cases of partial relaxation are explained. Experimental results for the discussed loads are introduced, which have led to satisfactory agreement between theory and experiment. (orig./MM).
Zusammenfassung Hintergrund Seit 2005 finden schriftliche Anfragen und Vor-Ort-Pr?fungen durch den Medizinischen Dienst der Krankenversicherungen (MDK) statt. Diese spiegeln in ihren Ver?nderungen sowohl die Erfahrung der Kassen mit dem G-DRG-System (G-DRG German Diagnosis Related Groups) als auch der zust?ndigen ?rztlichen Mitarbeiter und des Krankenhauscontrollings wider. Wir wollten aufarbeiten, welche Entwicklung die MDK-Pr?fungen seit 2005 genommen haben. Hierf?r wurden s?mtliche Pr?fberichte seit Einf?hrung der Pr?fungen ausgewertet. Ergebnisse W?hrend anfangs haupts?chlich Fragen zur Kodier- und Dokumentationsqualit?t erfolgten, werden jetzt ?berwiegend Fehlbelegungspr?fungen durchgef?hrt. Zwischenzeitlich wurden konsequent die unterschiedlichen Klinikbereiche gepr?ft. Die Anfragen ...
More than 200 years after the birth of the steam engine, the first thermal engine ever invented, thermal engines such as steam turbines, gas turbines or internal combustion engines are still driving most generators for electric power generation, most machines, and most vehicles, and this will remain so until far into the next century. (orig.) [Deutsch] Mit Waermekraftmaschinen wie Dampfturbinen, Gasturinen und Verbrennungsmotoren werden auch heute - mehr als 200 Jahre nach der technischen Reife der Dampfmaschine (der ersten Waermekraftmaschine) - die meisten Generatoren zur Stromerzeugung, die meisten Arbeitsmaschinen und die meisten Fahrzeuge angetrieben. Und dabei wird es auch bis weit in das 21. Jahrhundert bleiben. (orig.)
In parking areas of large extent, the removal of engine exhaust gases, especially of their CO gas components with ventilation plant is mainly done by transverse ventilation over short paths. By their presence, the ventilation ducts required for this purpose often reduce the value of the parking space by restrictions with a consequent reduction of their acceptance by the users. Longitudinal ventilation without ducts can be a remedy in such cases. Depending on the required room air quality in the zones of highest loading, the volume flows with longitudinal removal are no greater than with conventional transverse ventilation. This article is concerned with the different methods of operation of the two systems. (orig./BWI)
Three different guidelines define the methods to be used for the quantification of exposures due to the incorporation of radionuclides. The adoption of the Euratom-directive into German law requires the adaptation of these guidelines. With this process, the experiences with the practical application of these regulations must be taken into account. (orig.) [Deutsch] Die Ermittlung der Koerperdosis durch inkorporierte Radionuklide ist in drei Richtlinien des Bundesministeriums fuer Umwelt, Naturschutz und Reaktorsicherheit (BMU) geregelt. Die Umsetzung der Euratom-Direktive in deutsches Recht erfordert die Anpassung dieser Richtlinien. Dabei muessen die bisherigen Erfahrungen mit diesen Richtlinien beruecksichtigt werden. (orig.)
This book is mainly a comparison of the cost of pollution with the cost of environmental protection. As to the causes of pollution, a difference is made between pollutants that accumulate and pollutants that do not accumulate. Because of pollutant accumulation it is necessary to carry out both subsequent pollution abatement measures and to take preventive action which helps to avoid pollutant emission. Growth models serve to substantiate why such preventive action is both ecologically and economically useful as a rule. Finally the study makes a comparison between some tools of environmental protection. It stresses in particular that, if a duty on emissions is levied, the polluter has to bear all the cost of the pollution, while at the same time the quality of the environment can be more successfully improved than by emission standards alone.
This conference of Deutsche Wissenschaftliche Gesellschaft fuer Erdoel, Erdgas und Kohle focused on energetic utilisation and recycling of waste materials and biomass, i.e. combustion, gasification and pyrolysis. Aspects of process control were gone into as well. [German] Die Fachbereichstagung der Deutschen Wissenschaftlichen Gesellschaft fuer Erdoel, Erdgas und Kohle beschaeftigte sich mit der energetischen und stofflichen Nutzung von Abfall und Biomasse. Verbrennung, Vergasung und Pyrolyse verschiedener Abfallstoffe sowie die Prozesssteuerung wurden eroertert.
This comprehensive final report for the Swiss Federal Office of Energy (SFOE) examines ways to optimise energy flows in mains networks that include distributed generation facilities. Increasing use of decentralised generation, its effects on the operation of low-voltage mains and the efficient use of the 400 V mains is discussed. The principles of operation and construction of controlled storage installations are discussed and concrete examples of their use in both grid-connected and island operation are quoted. Alternatives to storage are looked at from both the technical and economic points of view. The storage technologies used such as flywheels, supercaps, redox-flow batteries and lead-acid accumulators are briefly assessed and the results of simulations are discussed.
The research project aimed at the selection or development of wear-reducing measures for submerged components of hydroelectric power plants. This comprised the optimisation of hydraulic profiles as well as materials testing for abrasion and cavitation. Another field of research was the development of appropriate application processes. (orig.) [German] Das Hauptziel des Forschungsvorhabens bestand in der Auswahl bzw. Entwicklung geeigneter Schutzmassnahmen zur Verschleissminderung an wasserberuehrten Komponenten von Wasserkraftanlagen. Diesem Ziel untergeordnet waren neben der Optimierung hydraulischer Profile auch Materialuntersuchungen hinsichtlich Verschleissbestaendigkeit gegenueber Abrasion und Kavitation. Ebenso war die Entwicklung geeigneter Applikationsprozesse ein wichtiger Bestandteil der Aufgabenstellung. (orig.)
Trapezblechstege im Bruckenbau kommen trotz der groen Vorteile, die diese Bauweise bietet, in Deutschland bisher nur an einem Pilotprojekt zur Anwendung. Durch die charakteristischen Eigenschaften des Trapezbleches entstehen konstruktive und wirtschaftliche Vorteile gegenuber herkommlichen Bruckenbauweisen. Allerdings lassen die aktuell gultigen Regelwerke aufgrund fehlender Kenntnis zum Tragverhalten und mangelnder Erfahrung keine wirtschaftliche Ausbildung zu. Dies zeigt sich am Beispiel des Pilotprojekts. Die Ausbildung der Verbundfuge wurde hier nur sehr unbefriedigend gelost und verdeutlicht somit die Notwendigkeit einfacher und praktikabler Verbindungsmoglichkeiten. Am Institut fur Leichtbau Entwerfen und Konstruieren der Universitat Stuttgart wurde in Zusammenarbeit mit dem Institut...
Particulate Reinforced Titanium matrix composites (PRTi) exhibit some improved specific mechanical properties in comparison with those of unreinforced titanium alloys as a result of the combination of the high strength and stiffness of ceramic particles with the toughness and damage tolerance provided by the metal matrix. The poor tribological properties of the titanium exclude titanium alloys from applications where wear resistance is required (brakes, rotating parts, sliding parts). The addition of ceramic particles improves the tribological properties of metals sensitive to adhesive and /or abrasive wear significantly. In this work, the wear resistance and the friction coefficient of Ti6Al-6V-2Sn reinforced with TiC particles and Ti6Al-4V reinforced with SiC particles (prototype material) are compared with the unreinforced alloys. Pin on disc and pin on ring tests were carried out against standard steel (100Cr6) as a function of pressure, speed and temperature. The results show ...
Several components of high-temperature reactor units have roller bearings in order to carry out their motions without much friction. The use of such bearings poses friction and wear problems which cannot be mastered by commercial roller bearing technology. Possible improvements of coating, cage design and bearing materials as well as of their parameters were registered and studied. The service life of dry lubricated bearings was considerably improved. With a radial or axial load on the bearing of {>=} 10% of the static load, {approx_equal} 20x10{sup 6} rolling motions/actuations can be performed. The connections between surface compression and wear were determined, and optimum conditions for the transfer of lubricants from the cage onto the bearing race were worked out. Coating of corrosion-resistant roller bearing steels with the HRB-M{sub 0}S{sub 2} running-in coating could be proved. New cage designs and materials were tested with positive results. Alternative coatings (thin ...
ZusammenfassungUbelkeit und Erbrechen stellen zwei Symptome dar, die grundlich untersucht worden sind und bei Krebspatienten haufig auftreten. Die meisten Studien haben sich bislang mit Haufigkeit und Management dieser beiden Symptome befasst. Das Ziel dieser Studie bestand darin, ein besseres Verstandnis dafur zu entwickeln, wie Krebspatienten ihre Symptome erleben-insbesondere Ubelkeit und Erbrechen nach Chemotherapie-und welche Auswirkungen diese Symptome auf den Tagesablauf der Patienten haben. Neun Frauen mit unterschiedlichen Krebsleiden und Chemotherapie Regimes wurden zwecks Chemotherapie stationar aufgenommen und nahmen an der Studie teil. Es wurden halbstrukturierte Interviews einschliesslich einer Inhaltsanalyse in Anlehnung an Kvale durchgefuhrt (Klarung und Entwicklung neuer B...
This article argues the importance of ensuring initiatives aimed at improving children-s social and emotional well-being are based on sound participatory principles. The discussion posits links between the recognition of children, dialogic approaches to participation, changing conceptualisations of children and childhood, and children-s well-being. It explores these links in light of one particular initiative, Seasons for Growth (Graham, 1996, 2002, Seasons for Growth; Loss and Grief Education Program. MacKillop Foundation), an education programme built around emerging evidence that giving children a voice assists them to adapt to family change. The paper concludes with insights into what is involved when we locate notions of -having a say- as a key element in promoting children-s well-bei...
The prospective study includes 25 patients without pathology of the femoral head for the evaluation of the normal femoral head perfusion. In addition 34 patients with femoral head necrosis underwent i.a. DSA preoperatively before pedicled pelvic bone grafting. 15 patients after pelvic bone graft operation and 7 patients with medial femoral head fracture were also examined via superselective DSA. In cases with femoral head necrosis a rarefaction or interruption of the rami nutricii proximales, or an occlusion of the medial circumflex femoral artery were observed. Patients with medial femoral neck fracture showed an interruption of the rami nutricii proximales of the femoral head. Postoperative DSA - after pedicled pelvic bone graft - revealed a regular arterial graft perfusion in 82%. (orig.).
Zusammenfassung Hintergrund Endograftimplantationen im oder am Aortenbogen stellen besondere Herausforderungen an die Implantationstechnik und an die mechanischen Eigenschaften von Stentgrafts und ihren Einf?hrungssystemen, bedingt durch die Notwendigkeit, die Prothesen punktgenau abzusetzen und durch die mit der Biegung im Aortenbogen zunehmende Reibungswiderst?nde innerhalb der Einf?hrungssysteme. Die Endograftsysteme der 1. Generation (Talent?, Zenith TX 1?, TAG?) zeigten in dieser Lokalisation technisch bedingte Limitationen. Neue Prothesen Bei den seit 2004 und 2005 verf?gbaren neuen Stentgrafts (E-vita?, Zenith TX 2?, Valiant?, Relay?) sind diese Limitationen weitgehend ?berwunden. Durch technische Verbesserungen von Stentgrafts und Einf?hrungssystemen ist es nun m?glich, auch lange ...
In a water well sunk in the Grafschaft Bentheim region of northern Germany, small volumes of methane were emitted regularly and large volumes of methane in eruptions at irregular intervals. After some extreme gas eruptions in 2002 and 2004, the Grafschaft Bentheim district government initiated a project to investigate underground conditions in the region between Nordhorn and Bad Bentheim in order to prevent potential hazards to the locals population. The main purpose of the project was to provide information on underground mechanisms as far as possible in order to develop long-term safety strategies for freshwater supply in the region. (orig.)
The clinical feasibility of using interventional examination techniques was tested with an equipment combining fluoroscopy and MR imaging. This hybrid system showed to be of advantage in a great number of interventional examinations. The 1.5 Tesla magnet proved to be superior to open MR scanning systems in terms of image quality and scanning times. (orig.) [Deutsch] Es wurde die klinische Durchfuehrbarkeit interventioneller Techniken an einem kombinierten Durchleuchtungs- und MR-Arbeitsplatz untersucht. Dieses Hybridsystem erwies sich bei einer Vielzahl interventioneller Eingriffe als vorteilhaft. Der 1,5 Tesla-Magnet ist offenen MR-Systemen hinsichtlich Bildqualitaet und Messzeit ueberlegen. (orig.)
Apart from condensing the off-air condensers have a number of additional functions, which have been added more or less incidentally as development progressed. Advanced development of certain types of turbine condensers justifies the hope that these additional functions can be improved as power plants become cheaper and simpler.(orig.) [German] Kondensatoren haben neben ihrer Hauptaufgabe, der Kondensation des Turbinenabdampfes eine Reihe zusaetzlicher Funktionen, die sich z.T. im Laufe der Entwicklung eher beilaeufig ergeben haben. Der hohe Entwicklungsstand bei bestimmten Bauarten von Turbinenkondensatoren laesst die Erwartung zu, dass im Zuge der Vereinfachung und Verbilligung von Kraftwerksanlagen 'Nebenfunktionen' verbessert werden koennen. (orig.)
Attention Deficit Hyperactivity Disorder (ADHD) is a neurobiological disorder of early childhood onset. Defining symptoms are chronic impairments of attention, impulse control and motor hyperactivity that frequently persist until adulthood. Miscellaneous causes of the disorder have been discussed. Accumulating evidence from imaging- and molecular genetic studies strengthened the theory of ADHS being a predominantly inherited disorder of neurobiological origin. In the last 15 years, non-invasive brain imaging methods were successfully implemented in pediatric research. Functional magnetic resonance imaging studies gave major insight into the neurobiological correlates of executive malfunction, inhibitory deficits and psychomotoric soft signs. These findings are in good accordance with brain morphometric data indicating a significant volumetric decrease of major components of striato-thalamo-cortical feedback loops, primarily influencing prefrontal executive functioning (e.g. basal ...
With the combination of source ventilation and ceiling cooling for air-conditioning of working and recreation rooms, a ventilation system is available which fulfills the highest demands regarding thermal comfort. In order to utilize the advantages of this ventilation system with regard to air quality and thermal comfort to an optimum, the influence of the radiation exchange between cooling ceiling and walls on the flow in the room is investigated experimentally. Energy transfer from the walls to the cooled ceiling may result in an insufficient temperature of the walls compared to ambient air and in an upward flow on the wall surfaces (downward flow of) driven by gravity, which influences the flow pattern in the case of source ventilation. (orig.)
Fur die Trennung binarer Gemische wird zunehmend das Simulated Moving Bed (SMB)-Verfahren verwendet. Fur einen storungsfreien Betrieb mussen die Volumenstrome sowie die Umschaltzeit exakt eingestellt werden. In diesem Beitrag wird mit Hilfe des Coherence-Konzepts eine Methode aufgezeigt, mit der sich die Stellgroen fur einen dispersionsfreien SMB-Prozess bestimmen lassen. Fur Langmuir- und Anti-Langmuir-Isotherme konnen einfache explizite Gleichungen bei vollstandiger Trennung angegeben werden. Das Grundprinzip dieser Methode lasst sich auch auf andere Isotherme sowie fur die unvollstandige Trennung ubertragen.
In certain regions of the sea floor, water and methane from organic depositions have turned into a burnable form of ice, i.e. methane hydrates which contain more stored energy than all fossil fuel reserves. If they should desintegrate as a result of global heating, methane will be released and will contribute to further global heating. [Deutsch] Im Boden bestimmter Meeresregionen haben sich Wasser und Methan aus organischen Ablagerungen zu einer brennbaren Form von Eis vereinigt. Diese Methanhydrate speichern mehr Energie als alle fossilen Brennstoffvorraete. Wenn sie sich bei einer globalen Erwaermung zersetzen, koennte das entweichende Methan als Treibhausgas die Erde noch mehr aufheizen. (orig.)
The following subjects were discussed at the conference: Stability of welded joints, creep stress in CrMo steels, life prediction, developments in modern power plant steels, testing, calculation of deformation, crack propagation and crack analysis under complex loads. [German] Die Autoren der Tagung referieren ueber folgende Themen: Stabilitaet von Schweissverbindungen, Kriechbeanspruchung von Chrom-Molybdaen Staehlen, Lebensdauervorhersage, Entwicklungen fuer die Anwendung in modernen Kraftwerken, Prueftechnik, Berechnung von Verformung, Rissentwicklung und -bewertung bei komplexer Beanspruchung. (uke)
This update of a system concept entitled ``Maritime hazard prevention and water protection`` makes full use of the technical room for maneuver while considering that reasonable financial and economic conditions must be provided. The update allows on to continue or start the exploitation of feasible technical, logistic and information-technology development potentials. The same applies to the national maritime traffic safety measures developed for the German waterways. Considering the maritime hazards that have been prevailing in the coastal areas of the German North Sea, the conducted damage risk investigations suggest that a large-scale, disastrous oil contamination of the mud flats ecosystem cannot be excluded or controlled definitely in spite of the numerous measures taken. (orig.) [Deutsch] Mit der vorgelegten Fortschreibung zum Systemkonzept ``Gefahrenabwehr und Gewaesserschutz im Seeverkehr`` werden die technisch realisierten Handlungsspielraeume unter Beachtung der finanziellen ...
Heat pumps for residential space heating become an increasingly important alternative to the conventional heating system like gas or oil burner. They offer the opportunity to reduce CO{sub 2} emission associated with heating residential homes in Germany. High compressors efficiency and a wide operating map are required so that an economically viable heat pumps is achieved which meets the operational conditions for present and future heating systems. The design parameter of existing heating systems require relatively high condensing temperatures which can be achieved with dedicated compressor designs. The design of Scroll compressors specially adapted to these heat pumps is shown and their operation is explained. (orig.) [German] Waermepumpen fuer die Wohnraumheizung gewinnen an Bedeutung als Alternative zur konventionellen Gas- oder Oelheizung. Sie bieten die Moeglichkeit, die mit der Gebaeudeheizung verbundene Emission von Kohlendioxid in Deutschland zu ...
The textbook is primarily intended for radiologic staff and radiologic safety officers and gives information on the current regulatory provisions of the German X-ray Ordinance, applications of X-rays, quality assurance, organisational aspects of film processing and quality requirements of X-rays. An annex lists the guidelines of the Bundesaerztekammer (German National Chamber of Physicians) relating to quality assurance aspects, and further useful information on commercially available film-screen systems, the various associations of physicians in Germany, and requirements and performance of radiation surveys. (vhe) [Deutsch] Das vorliegende Lehrbuch, das sich vor allem an das technische Personal und an Strahlenschutzbeauftragte wendet, unterrichtet ueber die derzeit gueltigen Bestimmungen der Roentgenverordnung, die Anwendung von Roentgenstrahlen, ueber Qualitaetssicherung, die Organisation der Filmverarbeitung sowie ueber die Anforderungen an die Qualitaet von Roentgenbildern. Im ...
The regenerator of Stirling cycle machines has an relatively unknown potential for thermal shorting, because the thermal flow path within the solid of a randomly stacked wire mesh, which is defined by its 'connectivity', is unknown. Earlier publications have shown two principles of experimental techniques to quantify connectivity. One quantifies connectivity as a function of axial pressure using the electric current analogy, the other measures connectivity via the temperature gradients along a regenerator and a series-connected reference body of known conductivity. Both papers offer preliminary results of reduced usefulness related to the testing method or setup. This contribution describes a new setup and its technique, which results from the practical knowledge and experience of the first two attempts, and aims for an improved determination of connectivity of the original representative Stirling regenerators with and without housing. Please contact the author for ...
Only about 25% of residue accumulating in the Federal Republic of Germany is currently used for the purposes of energy. This residue will be converted into fuel for power stations by the Omega process when the dumping of waste with a calorific value in excess of 5 MJ/kg is prohibited with effect from 2005. This oxygen melting process is suitable for the local use of substitute fuels. Waste is converted into a high-quality synthesis gas with a wide range of uses. The Omega process combines drying, thermal decomposition, gasification and melting of the material used in a single-stage process. This is now technologically possible for the first time by combining a metallurgical cupola furnace with a traditional gas producer. The highly-calorific synthesis gas produced by the Omega process can be used in block heat and power stations or as an industrial fuel gas, instead of natural gas. It is also suitable as a starting material for synthesising methanol. The gas is specifically processed ...
The book is a German translation of an American textbook with the original title ''MRI Survival Guide'' and is intended to serve as an introductory guide for beginners or a reference book for quick information. Readers will find information on the fundamentals of the technology and methodology of MRI as well as all details of relevance to practice in a precise and easy-to-grasp arrangement, covering all anatomic areas of interest, illustrations and descriptions of characteristic signs of pathologic processes, high-quality and unusually large-sized diagnostic pictures, a modern didactic concept for quick orientiation, including surveys, tables, and reproductions for visualisation of contents. (orig./CB) [German] Praktisch jeder Mediziner wird im Laufe seiner Berufstaetigkeit mit der MRT konfrontiert - unabhaengig davon ob in der Radiologie, Orthopaedie, Gynaekologie, Chirurgie, Neurologie oder sonstigen Fachrichtung. Das Buch ist eine Uebersetzung ...
Since enterprises operating offices and facilities at geographically distributed sites have been establishing an intranet for inter-office communication at the management level, the idea of integrating another intranet for multi-site technological facility management comes naturally. The Aachen-based technology enterprise Eurem for this purpose developed a Network and Security concept with solutions that can be customized for linking a variety of computerized control and monitoring systems. The package includes a modular substation named modUS, which is open to the field side as well as to the management side, is capable of efficiently and reliably performing the facility management functions by way of remote controlling via intranets. (orig./CB) [Deutsch] Nachdem in den Unternehmen mit verteilten Liegenschaften die unterschiedlichsten Buerokommunikationssysteme ueber eigene Netzwerke verbunden werden, liegt es nahe, auch verteilte Gebaeudeautomationssysteme in diese Vernetzung ...
In 1986, following comprehensive preliminary studies, a 17 MW battery energy storage plant was set up in the insular power supply system of Berlin (West) for the purpose of frequency and output control and provision of immediate reserve capacities. The present paper reports on the initial task, and the dimensioning and construction of this large-scale demonstration as well as the costs entailed in this. It also relates the experiences gained with the operation of the battery energy storage plant in its function as a fast-responding control unit and gives an account of its economic efficiency. Recent studies on the economic efficiency of the plant in conditions as they exist in the present interconnected power supply system are presented. Finally the author reports on the experiences gained with individual plant components, i.e., battery, battery periphery, and power converter and quantifies the cost of plant operation, maintenance, and servicing. (orig./HW) [Deutsch] Im Inselnetz von ...
This report presents the results of the BMBF-sponsored project Fundamentals and models for assessing the effect of climate changes on soil, plant development and the crops of an economically significant range of farm products. Its aim was to study, by means of the results obtained for winter wheat, the dependence of plant growth on temperature, radiation and water as well as nutrient supply for other economically important crop types. Building on this, process-oriented, climate-sensitive agricultural ecosystem models for winter rye, winter barley, sugar-beet and winter intercrops were developed, verified and, in some sites, validated. First scenario calculations served to demonstrate the climate sensitivity of these models. (orig./KW) [Deutsch] Im vorliegenden Bericht werden die Ergebnisse des BMBF - Vorhabens `Grundlagen und Modelle zur Abschaetzung von Klimaaenderungen auf den Boden, die Pflanzenentwicklung sowie den verwertbaren Ernteertrag einer wirtschaftlich ...
Based on the first part of this report the molybdenum loadings of the red mud were varied and the activity of the catalytic additives was tested in a batch autoclave with TJP VR. The 30% Molybdenum loading (sample Nr. 6) was found to be optimum. Further testing with two vacuum residues (TJP VR and ARH VR) and sample Nr. 6, indicates the influences of the process parameters for hydrogen pressures of 9-15 MPa, temperatures of 440-475 C and residence times of 0-60 min. Obviously 440 C, 12 MPa and a residence time of 30 min are best conditions for hydrocracking of both vacuum residues with sample Nr. 6. (orig.) [Deutsch] Beruhend auf dem ersten Teil des Berichtes wird der Belegungsgrad der Rotmasse mit Molybdaen variiert und die resultierenden katalytischen Zusaetze werden in einem Autoklaven mit TJR VR getestet. Ein Belegungsgrad mit 30% Molybdaen (Probe 6) scheint optimal zu sein. Mit diesem Zusatz werden die Einfluesse der Prozessparameter bei ...
A study tour in autumn 1999, which was undertaken following the award of the Helmuth Burkhardt prize of Wirtschaftsvereinigung Bergbau e.V. to the authors, comprised visits to potash, molybdenum, lead, zinc, copper ore and coal mines in the mid-west of the USA. The Black Mesa Mine and Kayenta Mine of Peabody Western Coal Company in the Navajo Reserve in the north of Arizona, the Trapper Mine Inc. near Craig and the Twentymile Coal Company near Steamboat Springs, Colorado are described in this report. In addition to a brief description of the geology the coal winning is considered in greater detail. The Twentymile Coal Company was asked to explain the reasons for the successful operation of the colliery, which produces more than 5 mill. t anthracite per year by long wall working. (orig.) [German] Eine Exkursion im Herbst 1999, die durch die Verleihung des Helmuth-Burkhard-Preises der Wirtschaftsvereinigung Bergbau e.V. an Bergassessor Andreas Tschauder zustande kam, fuehrte zu Kali-, ...
It is demonstrated that highly dispersed molybdenum sulfide catalysts are prepared by using Mo(CO){sub 6} adsorbed on the support. The structure of ultradispersed molybdenum sulfide is suggested by EXAFS techniques to be different from that of MoS{sub 2}. The TOF of the thiophene HDS is almost invariant with the dispersion of molybdenum sulfide at a high molybdenum dispersion, whereas the TOF of the hydrogenation greatly increases with increasing dispersion. On the basis of the HDS activity and optimum Co/Mo ratio of Co-Mo/Al{sub 2}O{sub 3} catalysts having a variety of molybdenum dispersion fabricated by using carbonyl complexes, it is demonstrated that highly active HDS catalysts are prepared by highly dispersing molybdenum sulfide phases. Edge decorations of molybdenum sulfides by cobalt are suggested for the synergy generation between cobalt and molybdenum sulfides. (orig.) [Deutsch] Unter Verwendung von auf dem Traeger adsorbierten Mo(CO){sub 6} lassen sich hochdispergierte ...
Osteonecrosis (ON) of the hip joint remains an unsolved therapeutical problem. Diagnosis of ON of the hip has been improved by the technical progress of imaging modalities and better understanding pathomorphology. Over a long period only plain radiographs have been available. Scintigraphy and computed tomography contributed to differential diagnosis and early detection of bone necrosis. Diagnosis in an early reversible stage is of importance. Understanding of pathophysiology, early diagnosis and therapeutical approach has been significantly improved by MR imaging. Using the ARCO system all imaging modalities and their diagnostic viability are described in the five ARCO stages. At the end a diagnostic algorithm will be proposed. (orig.) [German] Die Osteonekrose des Hueftgelenks (ON) stellt noch immer ein nicht geloestes therapeutisches Problem dar. Die diagnostischen Moeglichkeiten bei der ON wurden in den letzten Jahren durch technische Fortschritte ...
Already, MR Imaging is superior in diagnostic imaging of joints in many cases; however, there have been recent developments, which are the subjects of this paper. With gradient-echo sequences acquired in 3D technique, it is possible to produce high-resolution images of joints in acceptable scantime, because gradient-echo sequences are less time-consuming than convential SE sequences. With the acquisition of two echoes, phase difference between water and fat protons have to be considered. 3D Imaging is capable of displaying complex pathology in a superior way, which should be useful in preoperative planning. Tissue contrast is altered by fat saturation or magnetization transfer in order to achieve better conspicuity of lesions. Although diagnostic value of some of these options is not yet clear and further clinical studies are needed, they are a promising possibility for improving MR Imaging of the joints. (orig.) [Deutsch] In der Gelenkdiagnostik gibt es einige neuere Entwicklungen in ...
As a partner in this project, Siemens Power Generation investigated the crack propagation characteristics of short cracks in CMSX4. This involved crack propagation tests under dynamic and static load, creep tests on samples of different geometries, and life calculations, with the following results: No typical short cracking behaviour was observed under dynamic loads. Short crack propagation at 950 C under static load is well described by the fracture mechanical parameter C* integral. Notched bar creep tests showed longer times to cracking for notched bars. [German] In dem Verbundprojekt hat Siemens Power Generation u.a. die Untersuchungen von Rissausbreitungsverhalten von Kurzenrissen in CMSX4 als Hauptaufgabe bekommen. Dabei wurden Rissausbreitungsversuche unter dynamischer und statischer Belastung, Kriechversuche an Proben verschiedener Geometrie und Lebensdauerberechnung durchgefuehrt. Die wesentlichen Ergenisse sind wie folgt kurz zusammengefasst. Bei ...
The enhancements described of high-performance CT systems of latest design have again confirmed the importance of CT systems for acute and selective diagnostic imaging. Higher availability, shorter exposure times, and better applicability and handling for examination of poly-traumata patients or patients of intensive care departments are some of the advantages achieved with CT systems which demonstrate CT system efficiency in addition to MRI, which for specific examinations will remain the modality of first choice for diagnostic evaluation. The Tomoscan Av-E presented here was able to answer all relevant diagnostic questions appearing in routine diagnostics and scientific work. For patients, examinations using the spiral CT technique also offers significant advantages. (orig./CB) [Deutsch] Durch die dargestellten Verbesserungen bei Hochleistungs-CT-Systemen neuester Bauart wurde die Bedeutung der CT fuer die akute und selektive Diagnostik erneut bestaetigt. Bessere ...
Owing to their key function in power production the technology of gas- and steam turbines has a very high importance. Gas turbines in particular have become much more efficient and show higher performance in cogeneration plants. The VDI group on materials engineering puts these issues at the centre of this report whose focus is on measures necessary to increase plant availability: damage analysis, materials optimisation, supervision of construction and repair. The report which looks at applications and practical experience is adressed to operators of gas-, steam-, and water turbine plants, manufacturers of turbines and their components as well as maintenance companies, experts and insurance engineers. (orig.) [German] Aufgrund ihrer Schluesselposition bei der Stromerzeugung kommen den Gas- und Dampfturbinen eine sehr hohe technische Bedeutung zu. Insbesondere die Gasturbine macht in den letzten Jahren eine rasante Entwicklung im Hinblick auf Erhoehung von ...
Shortened excerpt from the head notes: The emission limits laid down in the TA Luft concretize the scope of the measures ordered by the law to provide for protection against harmful effects on the environment. Air pollution abatement measures imposed by the competent authority as post-licensing requirements based on the BImSchG (German Federal Emission Control Act) in general are in compliance with the principle of reasonableness considering the terms allowed by the TA Luft for backfitting measures. With this decision, the court qualified the emission limits defined in the TA Luft to be substantial and legally binding standards, to be applied by the competent authorities in licensing and post-licensing administrative procedures, also in order to fulfill the intended task of concretizing the less definite concepts of law laid down in the relevant legislation. (orig./CB) [Deutsch] Verkuerzte Zitierung aus den Leitsaetzen: Die in der TA Luft aufgestellten emissionsbegrenzenden ...
Diseases of the mandible affect the soft tissues aside from the osseous manifestation. This can be shown clearly and in great detail by magnetic resonance imaging (MRI). MRI is the gold standard in the diagnostic evaluation of any internal derangement of the temporomandibular joint. Dental MRI requires high resolution techniques and in some cases also intravenous administration of contrast material. These techniques allow delineation of the neurovascular bundle. In the past few years new indications were formulated, for example, the evaluation of the integrity of the inferior alveolar nerve in trauma and in radicular cysts. New quantitative methods now enable insights into the pathophysiology. The objective of this review is to communicate accepted indications for MRI of the mandible and to present innovative applications. (orig.) [German] Mandibulaere Erkrankungen beteiligen neben dem Knochen Weichteilstrukturen, die sich mit der MRT klar und detailreich darstellen lassen. In der ...
This report describes work carried out in the context of TurboTech Interim for the development of a system for monitoring stationary gas turbines for approaching the stability limit of the compressor. The requirements for the system components were defined and the suitability of different types and positions of pressure sensors were examined and evaluated. It was found very early in the work that, due to the complexity of the object being monitored, one would not succeed in finding a simple criterion for monitoring the pump limit. Rather, apart from the selection of suitable sensors and optimum positions, one must analyse the present signals in different ways and create a decision matrix from this. Existing work on this subject is mostly concerned with the phenomena in the context of experiments on experimental compressors or is not suitable for the requirements of stationary industrial gas turbines. The project is being carried out in the context of TurboTech II with the main aims of: ...
In the present work the effect of different surface conditions on plasma nitriding response of AISI M2 high speed steel was investigated. The plasma nitriding of ground and sandblasted samples and drills was performed at temperatures of 400 C and 500 C for two gas mixtures: 5 vol.% N{sub 2} and 76 vol.% N{sub 2} in hydrogen. Surface layers were characterized before and after plasma nitriding concerning the microstructure, roughness, microhardness, chemical composition, phase composition and residual stress states. Machining tests were carried out with drills during which drilling forces and flank wear have been measured. A significant effect of the surface state prior to nitriding on residual stress states and the properties of the nitrided layer and untreated core has been observed. Thinner nitrided layers on ground and sandblasted samples were attributed to high compressive residual stress states and a stress affected diffusion of nitrogen and carbon. In the machining tests, ...
Purpose: The purpose of this study was to observe the process of fixation in liver specimens non-invasively by means of magnetic resonance. The fixation process of several formaldehyde-containing solutions was monitored with MRI and MRS at two different temperatures. Materials and Methods: Liver specimens were conserved in aqueous fixative solutions containing formaldehyde concentrations of 0.7, 1.8, 4 and 7.2% and at different temperatures of 5 C and 20 C. MRI was performed with T1-, T2- and PD-weighted TSE sequences, a 2D FLASH-sequence with and without magnetization transfer, and a FISP 3D-sequence on a clinical 1.5 Tesla MR whole-body unit, and MRS with {sup 1}H-spectroscopic methods (STEAM-sequence) on a 3 Tesla MR whole-body unit. Results: The diffusion of formaldehyde into the tissue was best identified on PD- and T1-weighted images as a band under the liver surface with increasing thickness, penetrating especially fast during the first three days. Spectroscopic measurements ...
Purpose: The aim of this study was to demonstrate the typical appearance of ganglioneuromas in computer-assisted tomography (CT), and magnetic resonance imaging (MRI). Material and methods: Retrospective analysis of diagnostic imaging (9 CT, 6 MRI) in 9 children aged 3 to 15 years with the histological diagnosis of ganglioneuroma. Results: The tomographies showed large (max. 13.4 cm in diameter) round or oval tumors with sharp delineation. The sites of the tumors were the retroperitoneum (5), the mediastinum (3), and the adrenal gland (1). Intraspinal tumor involvement occurred in 4 cases. On comparing CT with MRI, MRI was more accurate in defining the intraspinal involvement. The ganglioneuromas were of hypodense appearance in the native CT scan and showed moderate enhancement upon administration of contrast media. In five patients tumor calcifications with a disseminated sprinkled pattern were seen in CT. In MRI T{sub 1}-weighted scans the tumors were homogeneous and hypointense, ...
A system for partial mechanisation of the support work with roadway driving machines consisting of a crawler undercarriage carrying a selective cutter with a cutting jib on a rotary tower is claimed. The system comprises a support manipulator movable in longitudinal direction over the rotary tower and cutting jib and a preassembly table with a number of brackets to take up and preassemble a support structure consisting of profile segments, preferably an arc-shaped support with a cap made up for several parts. The system is characterized in that the preassembly table is mounted on one side of the selective cutter and has one straight vertical guide bar each for at least two cap brackets which can be continuously adjusted in height, and in that the manipulator mounted on the selective cutter has a horizontally suivelling head which may grip under the cap of the preassembled structure on the preassembly table.
The contribution outlines the current status of the building construction projects for the German Bundestag in Berlin. The following subjects are discussed: Energetic quality of the building, energy supply concept, integrated energy supply system, electric CHP systems, cogeneration (vegetable oil), aquifer storage (heat storage, cold storage), solar energy (photovoltaic energy conversion, thermal solar energy use), economic and ecological aspects. (HW) [Deutsch] Der vorliegende Beitrag gibt einen Ueberblick ueber den aktuellen Stand des Bauvorhabens des Deutschen Bundestages in Berlin. In diesem Zusammenhang wird auf folgende Themen eingegangen: Energetische Gebaeudequalitaet, Energieversorgungskonzept, Energieverbund, stromgefuehrte BHKWs, Kraft-Waerme-Kopplung (Pflanzenoel), Aquiferspeicher (Waermespeicher, Kaeltespeicher), Sonnenergienutzung (Photovoltaik, thermische Solarenergienutzung), Wirtschaftlichkeit und Oekologie. (HW)
Computerized descriptions of isothermal, multi-stage creep fatigue load were established for one melt each of steels of the type 1%CrMoNiV and 12%CrMoV and were implemented in the service life prediction program SARA 2. SARA 2 predicts the time and number of cycles to incipient cracking for a given number of part cycles on the basis of rules for description of cyclic deformation and damage and of a generalized damage accumulation hypothesis. [German] Fuer je eine Schmelze der Staehle vom Typ 1%CrMoNiV and 12%CrMoV wurde eine rechnergestuetzte Beschreibung fuer isotherme mehrstufige Kriechermuedungsbeanspruchung erstellt und in ein Lebensdauerzaehlerprogramm SARA 2 implementiert. Auf der Grundlage von Regeln zur Beschreibung von zyklischer Verformung und Schaedigung unter Anwendung der verallgemeinerten Schadensakkumulationshypothese ermittelt SARA 2 fuer beliebig vorgebbare Teilzyklen einen Vorhersagewert fuer die Anrissdauer und die Anrisswechselzahl. (orig.)
In the context of the research project, the physical basis of the direct decoupling of highly concentrated solar radiation in materials without the detour via absorbing heat exchanger walls was examined. Also, the first chemical processes suitable for the effective long-term storage of solar energy were analysed, relevant experiments were carried out and the necessary receiver techniques for high temperature applications were provided. The principle of direct coupling was examined on fluidized beds on the one hand and on cavity receivers, on the other hand. The contribution shows the results achieved in detail. It is recorded that first processes for storing solar energy in chemical reactions were able to be examined. Alkaline earth hydroxides accommodated in ceramic honeycomb structures seem to be possible as stores for medium temperature ranges around 500deg C. Investigations on receiver structure materials are also making progress. Highly transparent, high temperature-resistant ...
On February 20th 1998 Auckland, the biggest city of New Zealand, was nearly paralyzed by an extended power failure. On this day the last of four cables supplying the central business district failed and caused a five weeks lasting blackout. This failure has caused costs of 128.3 Mio NZ Dollar for the affected utility Mercury Energy Ltd. The official ministerial inquiry was published on July 21st 1998 and reproaches the utility in an unusual clear manner. (orig.) [Deutsch] Am 20. Februar 1998 wurde Auckland, die groesste Stadt Neuseelands, von einer folgenschweren Unterbrechung der Stromversorgung nahezu lahmgelegt. An diesem Tag fiel das letzte von vier 110-kV-Kabeln zur Versorgung des Innenstadtbereiches aus und verursachte damit einen 5 Wochen dauernden Stromausfall. Diese Versorgungsunterbrechung hat bisher Kosten in Hoehe von 128,3 Mio NZ Dollar (rd. 115,5 Mio DM) fuer den oertlichen Stromversorger Mercury Energy Limited verursacht. Der am 21. Juli 1998 ...
A patent is claimed for a process by which a low-hydrogen gas containing at least 90 percent by volume of methane which is suited for natural gas substitution is produced by transformation of vaporizable hydrocarbons with the aid of steam in the presence of a catalyst containing nickel, at temperatures of 350 to 600/sup 0/C and at increased pressure. Hydrocarbons and steam are supplied to the reaction in mixed form with recycle product gas. Per kilogramme of hydrocarbons to be converted in the high btu gas reactor, less than 1 kilogramme of fresh steam is needed. High btu gas is fed back from the high btu gas reactor to the input end of the same via a gas cycle comprising a cooler, a carbon dioxide absorption device, and a saturator. Between the carbon dioxide absorption device and the saturator a product gas is branched off which may pass a methanation device.
Plasma Immersion Ion Implantation (PIII) is a new hybrid technology for surface treatment of materials based on the principles of plasma nitriding and ion implantation. The equipment and the operation of the system are introduced. As well as providing an alternate method of ion implantation, it is possible to combine energetic ion bombardment with plasma nitriding. Different metal materials and treatment conditions have been studied. The capability of PIII-treatment to improve the properties of a wide range of metals has been proven. Application for forming tools and their industrial test has been successful. (orig.) [Deutsch] Die Plasmaimmersionsimplantation (PIII) ist eine neue Hybridtechnologie zur Behandlung von Werkstoffoberflaechen und basiert auf den Prinzipien des Plasmanitrierens und der Ionenimplantation. Die Anlagentechnik und die Arbeitsweise werden vorgestellt. Verfahrensspezifische Vorteile entstehen durch die Moeglichkeit, sowohl alternative ...
A computer program for optimization of modular cogeneration plants is introduced. Computer calculation fundamentals are discussed referring to examples which elucidate the verification of the calculated data by measured data or empirical values. The results obtained as one optimizes plants by varying their size or by splitting them into modules are introduced referring to examples. Sensitivity analyses are made to investigate the influence of parameters such as fuel prices, electricity tariffs and interest rates. (orig.) [Deutsch] Im vorliegenden Beitrag wird ein Computerprogramm zur Optimierung von BHKW-Anlagen vorgestellt. Zunaechst werden in einem ersten Schritt die Berechnungsgrundlagen an einem Beispiel in Hinblick auf ihre Ueberpruefung durch Messdaten oder durch Erfahrungswerte diskutiert. Dann werden in einem zweiten Schritt exemplarisch die Ergebnisse einer Optimierung durch Variation der Gesamtanlagengroesse auf Aufsplittung der Anlage in Module ...
A model describes the effect of changes to the pore structure on the mechanical properties of semi-coke during coking. The gap tensile experiment makes it possible to determine the mechanical properties of the coke and semi-coke; a theoretical analysis is valid for the deformation of samples in the gap tensile test, by which the gap tensile strength of the coke can be determined, and by which a method for the simultaneous determination of the effective modulus of elasticity was developed. The effect of the pore structure on the mechanical properties is given in semi-empirical equations. The main point here is to check whether a pore in the coke can be regarded as a Griffith crack, and whether the interaction of pores can be neglected. A model which takes the pore distribution into account was also developed and tested. A model for the change of pore structure during coking, which includes the contraction of the semi-coke, and which presupposes a difference in direction of the ...
The generation of a defined swivel momentum in car door hinges depends on numerous constructional and technical manufacturing parameters. If these parameters and their influence are to be investigated, then in addition to detailed experiments with variations in the parameters, methods are also required which enable the measuring data produced to be assessed in such a way that, in general, the non-linear relationships between initial and target size can be described sufficiently accurately. This paper explains the parameter reduction necessary in the experimental investigation, gives the results of the data assessment with conventional statistical methods and describes in particular the use of artificial neural networks (ANN) to construct so-called 'neuro hinge models' on the basis of the data resulting from the experiments. Parameter variations can be simulated with the hinge models and in this way optimal constructional and technical manufacturing values for ...
The liberalisation of the energy markets requires completely new demands to the information processing procedure of energy supply enterprises. These requirements are to be understood as chances for strengthening of the terms of competition. In the following contribution to this subject the actual status of the concept as converted by the Electricity Supply Company of Halle (Saale) including their departments of district heating, gas and electricity supply will be presented. This concept are comprising all experiences as gathered so far as well as intended further actions to be executed. (orig.) [German] Die Liberalisierung der Energiemaerkte stellt fuer Versorgungsunternehmen voellig neue Anforderungen an die Informationsverarbeitung. Diese Anforderungen sind als Chancen zur Staerkung der Wettbewerbsfaehigkeit zu verstehen. Die Verfasser erlaeutern den aktuellen Stand des in der EVH GmbH Halle (Saale) im Querverbund der Sparten Fernwaerme, Gas und Elektrizitaet ...
The austenitic nitrided Cr-Mn steels CrMnN 1812, CrMnNMo 1714 and CrNiTi 1810 has been investigated in chloride nitric acid at temperature 20-60 C. The Potentials of pitting nucleation and the time for pitting initiation has been determinate by the hronoamperometric method. It was established that alloying only with nitrogen is not sufficient procedure for obtaining of resistive to localised corrosion steel structure. Of importance for the resistance to localised corrosion of Cr-Mn steels is alloying with molybdenum. (orig.) [Deutsch] Die austenitischen stickstoffhaltigen Cr-Mn Staehle CrMnN 1812, CrMnNMo 1714 und der klassische CrNiTi 1810 wurden in chloridhaltigen Salpetersaeureloesungen im Temperaturbereich 20-60 C untersucht. Durch die hronoamperometrische Methode wurden die Potentiale der Lochfrassbildung und die Zeit zur Initiierung der Lochfrasskorrosion bestimmt. Man stellte fest, dass das Legieren der Staehle nur mit Stickstoff eine nicht genuegende ...
Disposal of fine-particled byproducts via injection into a capola furnace using natural gas/O{sub 2} burners is a cost-efficient alternative to landfill dumping. Tests conducted in a foundry demonstrated that dusts collected there can be injected without detriment to melt-down rate and iron quality. The replacement of FeSi pellets with FeSi dust in addition reduced the slag content, while injection of coal dust permitted a decrease in coke consumption. (orig.) [Deutsch] Die Entsorgung von feinkoernigen Reststoffen durch Einblasen in einen Kupolofen ueber Erdgas/O{sub 2}-Brenner ist eine wirtschaftliche Alternative zur Deponierung. Anhand von Versuchen in einer Giesserei konnte aufgezeigt werden, dass hier anfallende Staeube ohne nachteilige Auswirkungen auf Schmelzleistung und Eisenqualitaet einzublasen sind. Die Substitution von FeSi-Formlingen durch FeSi-Staub brachte zudem eine Reduzierung des Schlackeanteils und das Einblasen von Kohlenstaub eine Verminderung ...
The technical potentials of electric power generation from hydro power in Germany, the current harnessing of hydro power, its costs, and certain characteristic quantities reflecting its effects on the environment are described. These diverse characteristic quantities are compared with those of other renewable and fossil energy sources used to generate electricity. On this basis, opportunities for extending the use of hydro power in Germany and its limits are discussed. (orig.) [Deutsch] Das Ziel der folgenden Ausfuehrungen ist, die technischen Potentiale und deren derzeitige Nutzung, die Kosten und bestimmte die Umwelteffekte beschreibende Kenngroessen einer Stromerzeugung aus Wasserkraft in Deutschland darzustellen. Diese unterschiedlichen Kenngroessen werden anschliessend mit denen anderer regenerativer Energien und fossiler Energietraeger zur Stromerzeugung verglichen. Ausgehend davon werden die Moeglichkeiten und Grenzen einer weitergehenden Wasserkraftnutzung ...
The adaption of the Muster-VAwS (model ordinance on the handling of water endangering substances in plants and specialized facilities) in the ordinances of the different German states, means that the legislator has laid down concrete - technical and organizational - requirements concerning the handling of water-endangering substances for all plants. The present example of the systematic stocktaking of all environmentally relevant substances in the context of the operation of the pumped storage plants of Schluchseewerk AG, Freiburg, an the application of the model operating instructions for hydropower plants shall serve to illustrate two important aspects for the implementation of this extensive ordinance. (orig.) [Deutsch] Durch Umsetzung der Muster-VAwS (Muster-Verordnung ueber Anlagen zum Umgang mit wassergefaehrdenden Stoffen und Fachbetriebe) in entsprechende Laenderverordnungen wurden durch den Gesetzgeber konkrete Anforderungen, technisch und organisatorisch, fuer alle Anlagen ...
The second volume contains a comprehensive presentation of inflammatory bone diseases, including seldom primary chronic osteomyelitis and morbus Paget. Substantial chapters on bone tumors and tumor-like lesions of bone joints are covering the state-of-the-art of diagnostic techniques of these seldom but important diseases. Besides the importance of projection radiography the contribution of MRI within differential diagnosis und staging of these diseases is emphasized. [German] Der zweite Band des Muskuloskelettalen Systems befasst sich mit der umfassenden Darstellung zur Diagnostik entzuendlicher Knochenerkrankungen und beinhaltet neben den klassischen infektioesen auch die seltenen, primaer chronischen Osteomyelitiden und den Morbus Paget. Umfangreiche Kapitel ueber die Knochentumoren und tumoraehnlichen Laesionen der Gelenke stellen in modernster Weise den aktuellen Stand des Wissens und der Diagnostik dieser seltenen, aber aus differenzialdiagnostischer Sicht ...
In the course of the research project 'Investigations of trace element concentrations in coal seams with different mineral groups', 31 seam coals of the Ruhr Carboniferous were analysed in order to determine the bending of 14 coal-relevant trace elements to the mineral groups and/or minerals of the coals. Products with different ash content were produced by fluctuation of the seam coals in a laboratory cell. The raw coals and fluctuation component products were analyzed chemically and mineralogically in order to get a quantitative raw material characterisation of the sampled material. Particular interest is taken in the chemical and non-ecological composition of the mineral as ash carrier in the coal and the fluctuation component products, as well as in trace element control. (orig./EF).
Beside sucker-rod-type pumps and submersible centrifugal pumps, excentric screw pumps (so-called progressing cavity pumps) belong to standard conveyors in the production of crude oil. The authors of the contribution under consideration present the further development of excentric screw pumps with respect to the reduction of fluid levels in gas wells. This further development is based on a co-operation between the operator (Rohoel Aufsuchungs AG (Gampern, Austria)), the pump supplier (NETZSCH Oilfield Products GmbH (Selb, Federal Republic of Germany)) and the Institute for Process Technologies and Machinery at the University of Erlangen-Nuernberg (Federal Republic of Germany). The authors report on first attempts with the excentric screw pump at Weizberg (Federal Republic of Germany), material investigations at the University of Erlangen-Nuernberg, optimization of pump components and pump systems as well as on the optimization of the entire drainage process. Although excentric screw ...
In car parks of considerable length, the removal of exhaust emissions, is carried out by air-conditioning systems mainly through transverse ventilation over short routes. The required air-conditioning ducts frequently produce a reduction in the available parking space simply due to their presence, resulting in restrictive effects on the level of acceptance by the users. In such cases, remedial action can be taken by creating ductless longitudinal ventilation. Depending on the required room air quality in the zones with the highest level of pollution, the volumetric flows for longitudinal disposal are no greater than those for conventional transverse ventilation. In conjunction with architecturally clear and positive lighting designs, clearly laid out car parks with a friendly atmosphere can be created which the user will be pleased to accept. (orig./BWI)
The criterion the study is based on in evaluating environmental risks is the possibility of harmful changes in air, water and soils rather than the harmful environmental impacts these changes are caused by. The two significant criteria, i.e. the evaluated environmental hazards potentials or 'value parameters', and the evaluated damage-to-the-environment probabilities or 'safety parameters', reveal the respective environmental risks or 'risk factors'. These risk factors are classified by 23 environmental risk parameters for differentiation between low-risk and high-aid for pollution abatement measures provided that one fixes acceptance limits for the environmental parameters. As a rule the environmental risks of technical facilities which handle hazardous materials can be evaluated appropriately and the results can be compared. (orig./HSCH).
A new material has been developed for welded low-pressure shafts in steam turbines. Nine test welds were examined in order to confirm the chemical analysis. A shaft disc with an optimized composition was produced and destructively tested. The new material demonstrates, both in a total forging and also in a joint weld examined, excellent strength and toughness characteristics as well as excellent resistance to corrosion. Accordingly, all the requirements for welded low-pressure shafts in steam turbines are fulfilled. (orig.) [Deutsch] Fuer geschweisste Niederdruckwellen in Dampfturbinen wurde ein neuer Werkstoff entwickelt. Zur Festlegung der chemischen Analyse wurden 9 Versuchsschmelzen untersucht. Mit optimierter Zusammensetzung wurde eine Wellenscheibe hergestellt und zerstoerend untersucht. Der neue Werkstoff zeigt sowohl im gesamten Schmiedestueck als auch in einer untersuchten Verbindungsschweissung gute Festigkeits- und Zaehigkeitseigenschaften sowie gute ...
Problems with the refractory liners of incinerator combustion chambers have accompanied incinerators from the very beginning. They increased during the past decade, owing to higher combustion temperatures required by law (17. BImSchV), the higher calorific values of the waste to be combusted, and the higher or changed pollutant concentrations in the waste materials. This caused the providers and the materials and the producers of incinerators to develop new refractory products and new design concepts, with a great variety of processes and cost levels. [German] Seit Beginn der Abfallverbrennung, insbesondere aber mit zunehmender Tendenz in den vergangenen 10 Jahren, wird ueber Probleme mit der Feuerfestauskleidung in den Brennkammern von Abfallverbrennungsanlagen geklagt. Als Gruende fuer die zunehmenden Korrosionsprobleme werden die hoeheren gesetzlich geforderten Verbrennungstemperaturen (17. BImSchV), die hoeheren Heizwerte der verbrannten Abfaelle und die hoeheren bzw. geaenderten ...
Melting in a cokeless cupola furnace fuelled with natural gas is a novel, energy-saving and environment-friendly process. In order to be able to monitor the processes inside the furnace with detailed mass and heat balances, an experimental furnace with an efficient measuring system was constructed in the framework of a research project financed by the BMFT and Messrs. Eisenwerke Dueker GmbH und Co. KG, Laufach, Germany. (orig./HS) [Deutsch] Das Schmelzen im kokslosen erdgasgefeuerten Kupolofen ist ein neues, energiesparendes und umweltfreundliches Verfahren. Um die Vorgaenge im Ofen mit umfassenden Stoff- und Waermebilanzen erfassen zu koennen, ist im Rahmen eines vom BMFT und der Firma Eisenwerke Dueker GmbH und Co. KG, Laufach, finanzierten Forschungsvorhabens, ein Versuchsofen mit umfangreicher Messeinrichtung gebaut worden. (orig./HS)
The report gives a brief introduction into the EU grant programmes since 1984 and explains the philosophy behind them. The current situation regarding grant opportunities for the construction and modernization of small hydroelectric installations is outlined. Hints are given with a view to grant applications. A selection of small hydro power stations supported by grants (since 1984) are described with their economic and technical features. (orig.) [Deutsch] In diesem Beitrag wird eine kurze Einfuehrung in die EU-Foerderprogramme seit 1984 und Erlaeuterungen zu der Programmphilosophie gegeben. Die derzeitige Situation bezueglich der Foerderung von Kleinwasserkraftanlagen fuer Neubauten und Modernisierungsmassnahmen wird dargestellt. Es werden Hinweise zur Stellung eines Foerderantrags beschrieben. Abschliessend erfolgt die Vorstellung einer Auswahl von gefoerderten Kleinwasserkraftanlagen (seit 1984) mit den wirtschaftlichen und technischen Besonderheiten. (orig.)
Since June 1990, the IMA ``CO2 Reduction`` has been working on a German air pollution abatement programme. Four reports were submitted in this period. The contribution presents the fourth of these reports. The measures taken, their state of implementation and the expected effects in 2000 and 2005 are presented in table form. (orig.) [Deutsch] Seit Juni 1990 befasst sich die Interministerielle Arbeitsgruppe ``CO2-Reduktion`` (IMA ``CO2-Reduktion``) mit dem deutschen Klimavorsorgeprogramm und hat seither vier Berichte vorgelegt. Im Folgenden werden neben der Ausgangslage und den Grundlagen fuer den 4.Bericht der IMA ``CO2-Reduktion`` die wesentlichen Inhalte des 4.IMA-Berichts dargelegt. In Tabellenform werden die einzelnen Massnahmen, ihre Art, der Umsetzungsstand sowie der erwartete Effekt in 2000 bzw. 2005 dargestellt.
A method was developed in which the potential of various measures is assessed systematically with a view to meeting the future EU5 emission specifications. Varied boundary conditions are taken into account, and their influence on the PM-NOx tradeoff was investigated. The relative cost is compared to an existing EU4 injection system. It was attempted to apply these measures to the impending US regulations (Tier2 Bin5) and to offer an outlook to EU6. The result shows that it is possible in principle for a car of the 1600 kg class to reduce NOx emissions while maintaining the EU4-PM emission standards.In the case of envisaged serial application subject to emission standards like US Tier 2 and EU6, much work is still required in terms of system robustness and life. In higher-class vehicles, the NOx reduction potential is lower, and it will be more difficult to make do without NOx treatment, especially with the NOx emission standard of US Tier2. (orig.)
Report by a participant in the International Nuclear Law School. In 2001, this advanced training course was first offered by the OECD-NEA together with the University of Montpellier and other international partners. This effort is intended to provide an overview of nuclear law, a discipline normally playing a subordinate role in curricula. In this way, a contribution is to be made to the important preservation of the existing knowledge base and to increasing know-how in this field. In 2003, the International Nuclear Law School will be continued with a new curriculum addressed to all interested participants. (orig.) [German] Erfahrungsbericht eines Teilnehmers der Internationalen Schule fuer Nuklearrecht 2002 an der Universitaet Montpellier. Erstmals im Jahr 2001 wurde diese Fortbildungsveranstaltung von der Nuclear Energy Agency der Organisation for Economic Co-operation and Development (OECD-NEA) zusammen mit der Universitaet Montpellier und weiteren internationalen ...
One part of the RWE measure catalogue in order to guarantee an environmental friendly and competitive electric power generation based on brown coal is to carry out measures improving the efficiency at existing steam turbines in RWE brown coal power plants. Since 1993 a total of 21 steam turbines with a gross capacity of 7,100 MW or net capacity of 6540 MW - this corresponds to approximately 70 % of the installed RWE brown coal power plant capacity - have been improved with an investment of approximately DM 500 million. The net block efficiency has been increased by 1.3 % on average. The planned net capacity increase of approximately 250 MW is still going to be achieved taking into account the pending enhancements. Nuclear power plant turbines have been successfully improved in the same way. Apart from the described retrofit programme measures to improve efficiency are carried out at further steam turbines of brown coal power plants. In the frame of this talk the measures taken are ...
To study the biogeochemical behaviour, mobility and transport of trace metals in seawater (Se, Mo, Cd, Pb, Hg, Cu, Co, Fe, Ni, Zn), in suspended particulate matter (Mo, Cd, Pb, Cu, Co, Fe, Ni, Zn, Al, Mn) and in sediments of the inner and outer coastal regions, samples were collected on 3 separate cruises during a one year period (Mai 1993 - April 1994) at 20 stations in the coastal area of Mecklenburg-Vorpommern. Standard hydrographic parameters, nutrients and dissolved oxygen were also measured. Priority was taken to establish the methods for the determination of molybdenum and selenium. To study the behaviour of these two elements in detail, longterm measurements were carried out weekly between January 1993 and June 1994 at the `Messsteg/Warnemuende`. Because of parallel measurements correlations to biological, chemical and hydrographic parameters have been tested. The total database is summarized in the Appendix. The results are presented in 30 figures and 13 tables and are ...
Primary malignant lymphoma of the brain is a disease of unknown etiology, which is increasing in incidence and has an unfavorable prognosis. Despite the lack of specific changes on CT or MRI in most cases, these procedures may typically facilitate the diagnosis: A focal-enhancing mass with subependymal spread on CT or MRI and hyperattenuation on nonenhanced CT are the most reliable features in the diagnosis of primary malignant lymphoma of the brain. Peritumoral edema and mass effect are usually not prominent features. On unenhanced CT scans they usually appear homogeneously isodense to mildly hyperdense relative to the gray matter. On MRI these tumors are slightly hypointense on T1-weighted images and slightly hpyerintense on PD- and T2-weighted images relative to the gray matter. On CT and MRI enhancement is usually homogeneous. Contrast-enhanced MRI, with its multiplanar capability, lack of bone-induced artifacts, and high-contrast resolution, is likely to reveal subependymal spread ...
To determined precisely a possible connection between the amount of copper in tap-water and the risk of early childhood liver disease, it was attempted through an epidemiological survey, to determine the extent of excessive concentrations of copper in the tap-water of households with copper pipes. Water samples from 956 households were tested for copper, and the state of health of the infants in these households was documented. Infants who had been fed using water with a copper concentration of 0.8 mg/l or more received a paediatric examination with a blood serum analysis to rule out any liver damage. A copper level greater than 0.8 mg/l was found in only 2% of the households examined. Eight infants were examined by a paediatrician and their serum was analysed. These infants had either been breast-fed to the 12th week or had received more than 200 ml of tap water per day during first 12 months. None of the infants examined showed any signs of liver malfunction. From the results of the ...
Subject of this study is the question of whether cone beam CT (CBCT) images with reduced projection data are suitable for use in adaptive radiation therapy (ART) treatment planning. For this purpose image quality and dose calculation accuracy depending on imaging modality were analysed. In this context, two CBCT-methods will be indicated having reduced projection data sets: Scans acquired with 200^o rotation angle in order to accelerate the CBCT process (half scan), or scans with an asymmetric cone beam and detector offset, used to enlarge the field-of-view (half fan). Methods: For three different CBCT-modes (On-Board-Imaging, Varian Medical Systems), two of them based on reduced projection data, and a conventional multidetector CT system, the main image quality parameters were studied. Tr...
The authors investigated the development of tribochemical reaction layers and surface-level structural changes in a fuel-lubricated roller bearing steel 100Cr6 in the limiting friction range, using two different variants of surface treatment and heat treatment. Tribological experiments were carried out in a laboratory test stand with reversing sliding wear under varying loads and with a varying number of friction cycles. [German] Ziel der vorliegenden Arbeit war es, die Entstehung von tribochemischen Reaktionsschichten und oberflaechennahen Gefuegeaenderungen am Waelzlagerstahl 100Cr6 bei Kraftstoffschmierung im Grenzreibungsbereich fuer je zwei Oberflaechenbearbeitungen und Waermebehandlungen zu untersuchen. Dazu wurden tribologische Kurzversuche in einem Laborpruefstand mit reversierender Gleitbeanspruchung unter Variation der Last und der Anzahl der Reibzyklen durchgefuehrt. (orig.)
The conference reviewed the state of the art of stationary fuel cell systems, concepts, and the next steps to be taken. Fuel cell systems of several hundred kW have been designed and constructed already. Systems for domestic power supply are in the range of several kW. [German] Die in den letzten zehn Jahren gewonnenen Erfahrungen mit den ersten Pilotanlagen sind eine wichtige und unentbehrliche Hilfe den Weg in den Markt fuer die Brennstoffzelle zu ebnen. Der vorliegende Tagungsband soll diese Erfahrungen fuer die stationaer eingesetzten Brennstoffzellen zusammenfassen und ein aktuelles Bild ueber die daraus gewonnenen Konzepte und Vorstellungen fuer die naechsten Schritte aufzeigen. Bei Energieversorgern sind hier Leistungsgroessen von bis zu mehreren 100 kW eingesetzt worden. Der Leistungsbereich, der fuer die Aufgaben der Hausenergieversorgung typisch ist, befindet sich demgegenueber im Bereich einiger kW. (orig.)
The development of the space HVAC sector during the past 25 years is reviewed. It is shown how the importance of room climate has increased, as illustrated, e.g., by the concepts of 'thermal comfort', 'comfort', and 'sick building syndrome'. A sequel will be published in the next issue of KK. (orig.) [German] Der folgende Beitrag ist eine Bestandsaufnahme im Hinblick auf technologische Entwicklungen in der Klima- und Lueftungstechnik der letzten 25 Jahre, ein Zeitraum in dem sich einiges veraendert hat. Gleichzeitig wird deutlich, welcher Wandel sich bei der Bedeutung des Raumklimas in Gebaeuden vollzogen hat, indem beispielsweise Begriffe wie ''Behaglichkeit'', ''Komfort'' aber auch ''Sick Building Syndrom'' eine immer groessere Rolle spiel(t)en. Die Fortsetzung in der naechsten KK-Ausgabe wird dann ...
Proactive qualification is today an integral part of the development process for steam turbines used in steam and combined cycle power plants. By providing experimentally based `random` variables, such as the steam path efficiency and blading reliability, it makes a valuable contribution to the economic `random` variables of the power plant, e.g. the rate of return, as viewed by the customer. One of the areas in which proactive product and process qualification plays an important role is the development of LP steam paths. (orig.) [Deutsch] Die proaktive Qualifikation ist heute fester Bestandteil des Entwicklungsprozesses bei Dampfturbinen, die fuer den Einsatz in Dampf- und Kombikraftwerken bestimmt sind. Sie leistet mit Hilfe experimentell ermittelter `Zufalls`-Variablen, wie z.B. Wirkungsgrad der Fluten und Zuverlaessigkeit der Beschaufelungen, einen wertvollen Beitrag zu den fuer die Kunden wichtigen wirtschaftlichen `Zufalls`-Variablen des Kraftwerks, wie etwa ...
Within the context of practice-oriented constraints the speed and output power control of power plant turbines represents a big challenge for engineers for designing low order controllers with only a few parameter settings and in order to meet the requirements of the Deutsche Verbundgesellschaft. The results of a detailed study of the current standard and an improvement of the speed dynamic for load rejections are shown. (orig.) [German] Die Regelung der Drehzahl und die Leistung von Kraftwerksturbinen stellt im Rahmen von praxisorientierten Nebenbedingungen, wie z.B. dem Einsatz von Reglern geringer Ordnung mit wenigen Einstellparametern und den Vorgaben der Deutschen Verbundgesellschaft, eine grosse Herausforderung fuer den Entwicklungsingenieur dar. Die Ergebnisse einer ausfuehrlichen Untersuchung des bisherigen Standards und einer Verbesserung der Drehzahldynamik bei sogenannten Abfangpruefungen werden vorgestellt. (orig.)
Zusammenfassung Seit Dezember 2009 ist in Deutschland neben einem 10-valenten (PCV10) auch ein 13-valenter Pneumokokkenkonjugatimpfstoff (PCV13) verf?gbar. Ein Wechsel von PCV7 zu PCV13 ist zu jedem Zeitpunkt einer begonnenen Impfserie problemlos m?glich, von PCV7 zu PCV10 nur bei der Boosterimpfung. F?r alle Kinder mit abgeschlossener vollst?ndiger PCV7- oder -10-Impfserie stellt sich die Frage, ob eine zus?tzliche Impfung mit PCV13 sinnvoll ist. Kinder mit erh?htem Risiko f?r Pneumokokkenerkrankungen gem?? STIKO (St?ndige Impfkommission am Robert?Koch-Institut), die mit PCV7, jedoch nicht mit PPV23 geimpft sind, sollten grunds?tzlich mit PCV13 geimpft werden. Zu diesen Risikokindern sind evtl. auch gesunde, aber bereits im fr?hen Alter in Gemeinschaftseinrichtungen betreute Kinder zu rec...
Section 7 of the Atomic Energy Act (AtG), section 4 of the Federal Emission Control Act (BImSchG), the Nuclear Installations Licensing Ordinance (AtVfV), and the Ninth Ordinance on the Implementation of the BImSchG (Principles of the licensing procedure) require participation of the public in the procedure before administrative provisions or decisions are issued. The book presents the legally prescribed steps at which participation of the public is mandatory, for the simple case (only one license on the agenda), and for the multi-stage licensing procedure: preliminary negotiations / filling of applications for a license and filing of documents / public announcement of projects / access to files / objections / preclusion of delayed objections / public hearing and other expert discussions / termination of procedure, decision-making by the authorities / decisions on subdivision of procedure into defined stages / modification of the procedure. The analysis of the functions of participation ...
Optische Uhren nutzen die Anregung optischer Ubergange in neutralen Atomen oder Ionen. Deren Ubergangsfrequenz liegt bei etwa 1015 Hz, also funf Groenordnungen oberhalb der Gigahertz-Schwingungen heutiger Atomuhren. Das erlaubt eine bis zu tausendmal prazisere Zeitmessung. Fur die Genauigkeit ist es entscheidend, dass der Uhrenubergang eine schmale Linienbreite besitzt und seine Frequenz nicht verschoben wird. Dazu mussen die Atome oder Ionen moglichst ungestort und genau lokalisiert sein. Deshalb basiert ein Uhrentyp auf einem kalten Ion in einer Paul-Falle, ein anderer Uhrentyp arbeitet mit vielen kalten Neutralatomen in optischen Gittern. Der Metrologie sollen optische Uhren zunachst als sekundare Realisierung der Sekunde dienen. Derzeit ermoglichen sie bereits Frequenzmessungen mit 17 ...
Until now, monitoring of power transformers focussed mainly large generator and network transformers. Siemens goes a step ahead and provides a system especially developed and designed for small and medium power transformers, e.g. for the 100 kV level. This low cost version could be achieved by restriction to really necessary measuring quantities. This allows to realize also for small and medium power transformers an online monitoring including an estimation of aging and as an option an early warning to avoid unexpected failures. (orig.) [German] Die Ueberwachung (Monitoring) von Leistungstransformatoren war bisher vor allem fuer Maschinentransformatoren und grosse Netzkuppeltransformatoren in der Diskussion. Siemens geht einen Schritt weiter und stellt nun auch ein System bereit, das speziell fuer kleine und mittlere Leistungstransformatoren, z.B. der 110-kV-Spannungsebene, konzipiert ist. Diese kostenguenstige Variante wurde durch Beschraenkung auf die aus technischer Sicht ...
Fuel cells can make an important contribution to ecologically acceptable energy supply. There are many pilot projects in the 1 W to 1 MW range. Especially the motor car industry is quite interested, and a breakthrough seems to be in sight. The second part of this series discusses the physical and chemical fundamentals of the fuel cell, the function of the electrolyte and catalyst, and the functional principle. (orig.) [German] Brennstoffzellen koennen bei der Riesenaufgabe, den weiter wachsenden Energiebedarf oekologisch vertraeglicher als bisher zu decken, einen wichtigen Beitrag leisten. Bis heute (2004) gibt es zahllose Pilotprojekte im Leistungsbereich 1 W bis ueber 1 MW, die die Alltagstauglichkeit der BZ beweisen. Verschiedenste Branchen - vor allem auch die Automobilindustrie - zeigen grosses Interesse fuer kommerzielle Anwendungen. Die Brennstoffzelle als effizienter Energiewandler, scheint vor dem Durchbruch zu stehen. Der zweite Teil befasst sich mit den ...
Infrainguinal peripheral occlusive disease is increasingly being treated by endovascular techniques. Bare metal stainless steel, self-expanding nitinol stents, drug-eluting and covered stents (stent grafts) are becoming increasingly more important adjuncts to percutaneous translumninal angioplasty in the treatment of peripheral artery disease. In this article the available evidence supporting the use of stents in the femoropopliteal and tibial arteries will be described as well as their limitations. Future stent developments will also be discussed. (orig.) [German] Die endovaskulaere Therapie spielt bei der Therapie der peripheren arteriellen Verschlusskrankheit (PAVK) eine wichtige Rolle. Unbeschichtete ballonexpandierbare Stahlstents, selbstexpandierende Nitinolstents sowie medikamentenbeschichtete und ''covered stents'' (Stentgrafts) haben eine zunehmende Bedeutung als Zusatztherapie zusammen mit der primaeren ...
Liberalisation of the energy market will lead to enhanced use of environment-friendly, high-efficiency combined-cycle power stations - a great challenge to steam turbine producers. In this highly competitive market, advanced technology and interesting technical features are key issues. MAN Turbomaschinen AG GHH BORSIG, Oberhausen and Berlin, have been producers of steam turbines since 1905. Performance optimisation is the main aspect of development today. [German] Die jetzt eingeleitete Liberalisierung des Energiemarktes wird in der Zukunft den verstaerkten Einsatz von neuen umweltfreundlichen und zugleich hoch effizienten Kombikraftwerken notwendig machen. Eine grosse Herausforderung an fuehrende Hersteller modernster Dampfturbinen. Eine ausgereifte Technik sowie technische Alleinstellungsmerkmale sind im heutigen Verdraengungswettbewerb eine Voraussetzung bei Industriedampfturbinen. Seit dem Jahre 1904 baut die MAN Turbomaschinen AG GHH BORSIG, Oberhausen und ...
The phenomenon of the limit of pitting corrosion in direction to positive potentials is studied by potentiokinetic polarization after a jump in the transpassive range and by potentiostatic tests at technical wrought materials and at model alloys of the systems NiCrMo and NiMo in CaCl{sub 2} solution in the concentration range 1 to 9 mol/l chloride at pH-values of 1 to 9 at temperatures of 30 to 110 C. Surface-analytical investigations gives in connection with knowledges from anodic polarization studies directions to the mechanism of the limit of pitting corrosion. Ranges of the limit of pitting corrosion are obtained at materials with a Mo content above 6.5% and contents of chloride of the media above 2 mol/l chloride. Increasing temperatures, increasing contents of chloride and sulfate shift the potential of the limit of pitting corrosion being always above 0.2 V (SCE) at potentiostatic determination to noble direction. There are indications that the mechanisms of limit of pitting ...
Despite successful reduction of the general lead exposure, this heavy metal is still a matter of public concern due to the fact that associations with intellectual impairment or delayed puberty are found to correlate with very low lead blood concentrations. Lead in tap water is still an important contribution to lead exposure which may cause health risk for infants. Therefore, lead pipes should be completely sanitated by exchange against pipes made from more healthy materials. (orig.) [German] Trotz erfolgreicher Reduktion der allgemeinen Belastung ist Blei auch heute noch umweltmedizinisch relevant, weil es moeglicherweise bei niedrigeren als bisher angenommenen Belastungen gesundheitlich nachteilige Wirkungen, insbesondere waehrend der fruehkindlichen Entwicklung des Nervensystems, ausloest. Insbesondere Blei aus bleiernen Trinkwasserleitungen ist eine Belastung, die fuer Saeuglinge und Kleinkinder nach wie vor ein gesundheitliches Risiko darstellen kann. Solche ...
The paper examines the influence of various total strain amplitudes and mean strains on the cyclic deformation processes in GGG-60 at temperatures of 20 C, 350 C, and 500 C ,the total strain amplitudes being varied between 1.0 permille {<=}{epsilon}{sub a,t}{<=}3.8 permille , and the mean strains between -4.0 permille {<=}{epsilon}{sub m,t}{<=}4.0 permille . - [Deutsch] In der Arbeit wird der Einfluss unterschiedlicher Totaldehnungsamplituden und Mitteldehnungen auf das Wechselverformungsverhalten von GGG-60 bei Temperaturen von 20 C, 350 C und 500 C untersucht. Dabei werden die Totaldehnungsamplituden zwischen 1,0 permille {<=} {epsilon}{sub a,t} {<=} 3,8 permille und die Mitteldehnungen zwischen -4,0 permille {<=} {epsilon}{sub m,t} {<=} 4,0 permille variiert. (orig./MM)
Until recently no active treatment for advanced or metastatic gastrointestinal stroma tumors (GIST) was available. The tyrosine kinase inhibitor imatinib has revolutionized the treatment of this disease and the median overall survival now reaches 5 years. The standard dose of imatinib is 400 mg per day. Locally advanced GIST should be treated with systemic therapy prior to surgical resection. Imatinib was recently licensed for adjuvant therapy following complete surgical removal of GIST in patients with a significant risk of recurrence. (orig.) [German] Bis vor einigen Jahren existierte keine wirksame systemische Therapie fuer fortgeschrittene oder metastasierte gastrointestinale Stromatumoren (GIST). Der Tyrosinkinaseinhibitor Imatinib hat die Behandlung dieser Tumoren revolutioniert, die mediane Ueberlebenszeit liegt heute bei etwa 5 Jahren. Die Standarddosierung von Imatinib betraegt initial 400 mg/Tag. Lokal fortgeschrittene Tumoren werden primaer systemisch ...
The research project had the aim to develop a standard for measuring individual, inner stresses from polycyclic aromatic hydrocarbons (PAHs) at work. The employed method was by characterizing PAHs and metabolites of PAHs to be identified in urine with a view to developing a biological monitoring of professionally exposured persons. Using a number of PAHs relevant to work, the following questions were studied in cell culture systems and different animal-experimental models: Which metabolites are formed from the PAHs used in cell culture systems and the different animal-experimental models, and what are their ratios in percent What percentage of a PAH is excreted by experimental animals in their urine and faeces on the first, second, and third day following different forms of application What is the scale of the individual range of variation of PAH mass excretion Are these results transferable to man (orig.).
The harnessing and enhanced use of renewable energy today is a matter of lively debate and much concern. Amazingly, hydro power is either rarely considered in these discussions or viewed in a negative light. But hydro power continues to be the most important source of renewable energy, and its use potential is considerable and should be taken into account when, for instance, agreeing on or implementing carbon dioxide reduction targets. Small hydro power stations are an effective means of harnessing existing energy potentials. (orig.) [Deutsch] Ueber die Nutzung und den Ausbau regenerativer Energien wird heutzutage lebhaft diskutiert und gerungen. Es mag erstaunen, dass in diesen Diskussionen die Wasserkraft kaum Beachtung findet oder in einem schlechten Licht gesehen wird. Dabei ist die Wasserkraft nach wie vor bei weitem die wichtigsten Quelle regenerativer Energie, und sie besitzt ein beachtliches Ausbaupotential, das man wenigstens ins Kalkuel ziehen sollte, ...
Ventilation, cooling and illumination of modern high-rise office buildings with high-quality thermal insulation (average k-value 1.0 W/m12K) and high loads from office machinery (up to 20 W/m12 and beyond) are problematic even for modern facility management systems, with consequences for the building shell, heating system, and window ventilation. [Deutsch] Die Lueftung, Kuehlung und Beleuchtung moderner Buerohochbauten mit extremer Waermedaemmung (mittlerer K-Wert 1,0 W/m{sup 2}K) und hohen Bueromaschinenlasten (bis zu 20 W/m{sup 2} und mehr) verursachen auch heute noch erhebliche Probleme, obwohl die technische Gebaeudeausruestung weiterentwickelt wurde. Dies zeigt sich vor allem bei der Fassadenausbildung der Heizung und Fensterlueftung. (orig.)
The results of these investigations can be summarised as follows: At simulated operating stress most naturally occuring faults in welded- and cast iron parts develop cracks and can be assessed for reliability under fatigue-,creep- and creep fatigue behaviour according to the laws of fracture mechanics. The empirically determined correlation between the real fault size and the ultrasonic inspection results (height of echo, echo dynamics, sound weakening) lead to better assessment of real fault extension in turbine components. It is very important to adapt the method of inspection and assessment to the type of possible fault.(orig.) [German] Die bei diesen Untersuchungen ermittelten Ergebnisse lassen sich wie folgt zusammenfassen: - Die Mehrzahl der untersuchten natuerlichen Fehlstellen in den Schmiede- und Gussstuecken verhalten sich unter den simulierten Betriebsbeanspruchungen rissartig und sind damit mittels den bruchmechanischen Gesetzen in ihrem ...
The gross calorific value (H{sub o}) is the amount of heat which is generated by total combustion of a type of fuel. It also includes that part of heat which is generated by steam from evaporated water contained in heating gas. In conventional heating boilers, this heat portion is not being utilized at all. To utilize the gross calorific value, it is necessary to extract from the exhaust gas the evaporation heat bound in steam and to return this to the heating system. This means that the exhaust gas has to be chilled by the return water of the heating system and condensed in suitable heat exchangers to well below the dew point. (orig.) [Deutsch] Waermelieferanten im Bereich der Nahwaermeversorgung koennen durch die Anwendung verfuegbarer und bewaehrter Brennwerttechnik ihre Kosten senken und einen zusaetzlichen Beitrag zum Umweltschutz leisten. Mit dem richtigen Brennwertkessel amortisieren sich Mehrkosten in weniger als 2 Jahren. (orig.)
In the last few years the supercharging of Otto-cycle-engines has regained popularity, as demonstrated by a number of series-production engines. After listing the aims to be met by a modern supercharger the paper describes the technical status of mass-produced or close to production superchargers. This is followed by a comparative evaluation of the systems, enabling the reader to select possible solutions for a projected supercharger-engine-system by means of a comparison chart. The paper is concluded by a list of possible directions for further development and additional potential for twin-screw superchargers. (orig.) [German] In neuerer Zeit hat die Aufladung von Ottomotoren wieder ein verstaerktes Interesse gefunden, das sich auch in einer Anzahl serienmaessig gefertigter aufgeladener Motortypen wiederspiegelt. Der vorliegende Beitrag beschreibt, nach einer Darstellung der Anforderungen an ein modernes Aufladegeraet, den Stand der Technik bei serienmaessigen ...
The analyses were carried out using real climate data for the years 1987 and 1989. The course of the indoor climate for year-round free ventilation with a constant flow volume is discussed. Numerous diagrams inform on ambient temperature, water vapour content, the condition of space air, and temperature drops below dew point. For the event of heating of the central part of the church, space air condition, the annual air humidification requirement, and the temperature field in this part of the building are described. (MSK) [Deutsch] Die Untersuchungen wurden mit aktuellen Klimadaten fuer die Jahre 1987 und 1989 durchgefuehrt. Der Verlauf des Raumklimas bei ganzjaehrig freier Klimatisierung mit konstantem Foerderstrom wird erlaeutert. Dabei wird die Raumlufttemperatur, der Wasserdampfgehalt, der Raumluftzustand sowie die Taupunktunterschreitung in zahlreichen Diagrammen aufgezeigt. Weiter werden fuer den Fall der Beheizung des Hauptraums der Kirche der ...
Epidemiological studies could not show an association between ionising radiation of nuclear power stations in routine operation and the incidence of childhood cancer, yet. The following report presents a case control study conducted by the German Childhood Cancer Registry since autumn 2003. All children in the study region, who were diagnosed with cancer between 1980 and 2003 at an age below five are included. In the first part of the study we investigate whether children with cancer (cases) lived closer to the respective nuclear power stations compared to random children without cancer (controls). In the second part, for a subgroup of cases and controls we conduct computer assisted telephone interviews regarding confounders possibly associated with the exposure of ionising radiation and childhood cancer. Results are expected by the end of 2006. (orig.)
We report for the first time about a micromachined mass flow sensor directly integrated between the double guidance and the needle seat into the body of a Common Rail (CR) injection nozzle. The thermal measurement principle was chosen because gaseous as well as liquid mass flows can be determined fast and precisely. Additionally, with glass-ceramic materials fabricated in a low cost batch process, a high temperature and especially pressure stable substrate can be used. The flow sensitive thin film is realized by an e-beam evaporated 110 nm thick molybdenum (Mo) layer. The latter is electrically characterized by the resistivity of {rho} = 8.2 x 10{sup -7} {omega} m ({+-}2%) at room temperature as well as by the first {alpha}=4.5 x 10{sup -4} K{sup -1} ({+-}5%) and second {beta}=3.0 x 10{sup -6} K{sup -2} ({+-}12%) temperature coefficients of resistance up to 300 C. The static temperature field at and around the thin film sensor on the glass-ceramic substrate is investigated with an IR ...
To test the assumption underlying every morphometric twin study that the brains of monozygotic twins are almost identical. Methods: High resolution MRI of the neurocranium of 26 monozygotic twin pairs were acquired and the volumes of 36 cerebral structures were measured. The same twins served as control group after rear-ranging them into non-related pairs of same sex and matching them for age, body height and body weight. Results: For most of the examined structures the correlations within the twins were significant (R = 0,97-0,59). Except for total forebrain volume the controls showed no significant similarity. Conclusions: For almost every measured cerebral structure the assumption, that significant similarities exist between healthy monozygotic twins is correct. Therefore discordant monozygotic twins represent an excellent sample when investigating cerebral correlates of neurologic and psychiatric disorders. (orig.) [German] Pruefung der Grundannahme hirnmorphologischer ...
A singular stress field can occur at the edge of the joint plane in a thermally or mechanically loaded material compound. This stress field was calculated analytically and was compared with the results from the finite element method. If one of the two partners consists of ceramic material, unstable crack spread starting from faults in this strongly stressed area can lead to failure. In linear elastic material, the behaviour of a crack is clearly described by the stress intensity factors. These can be calculated for a known stress distribution in the uncracked structure by the method of the weight function. The corresponding weight functions for surface cracks parallel to the boundary surface were determined with the aid of suitable reference load cases. The effect of the position of the crack in the compound and the elastic constants of the compound are discussed. For examples, the stress intensity factors for cracks in a thermally stressed material compound were determined by the ...
Magnetic resonance imaging (MRI) of the lung is challenging because of substantial drawbacks. However, lung pathologies that are associated with increased attenuation values in CT enhance visualization in MRI: proton density is increased and tissue-air interfaces, resulting in susceptibility artifacts, are reduced in pneumonia, pneumonitis, edema, and carcinoma. On the other hand, many lung diseases result in shortness of breath, so that patients cannot hold their breath for long periods. Therefore, fast imaging techniques are required which should also allow for high spatial resolution so that small lesions can be detected. Calcifications and air pockets within lesions are not readily recognized with MRI. Thin section CT is standard for the diagnosis of pneumonia. With parallel imaging techniques, MRI examination of the lungs can be performed with short periods of breath holding, which allow for sub-centimeter resolution in the z-axis. Especially for follow-up examinations in ...
60 patients between 17 and 72 years of age were investigated. First, an enteroclysis was performed in typical manner. The applicated methylcellulosis was blended with positive oral MR contrast media (Magnevist oral, Schering). After enteroclysis, MRI of the abdomen was performed using T1- and T2-weighted breathhold sequences (Flash 2D pre- and postcontrast and TSE) in axial and coronal planes. The length of the affected bowel and the stenosis seen with enteroclysis correlated well with the visible thickening of the small bowel wall and the stenosis seen in MRI. Using MRI, additional findings could be obtained in 28 patients, such as fistulas, abscesses or a hydronephrosis, or a better assessment of the stenosis was possible with MRI, because of the avoidance of overshadowing of the affected bowel loop with MRI. A brilliant MR-tomographic imaging of the small bowel is possible under the condition, that the small bowel contrast is optimal. The main prerequisite is a large filling volume ...
The aim of this review is to evaluate the role of inflammatory spine disease in patients with chronic back pain. The contribution of imaging modalities for the diagnostic evaluation of back pain is discussed. A systematic literature search based on the classification of seronegative spondyloarthropathies and rheumatoid arthritis was performed. The results of this search and the experiences in a large collective of rheumatological patients are analyzed. The prevalence of rheumatoid arthritis (1-2%) is comparable to that of spondyloarthropathies (1.9%). The etiology of these entities is not fully elucidated. Magnetic resonance imaging is increasingly used for early detection and surveillance of therapy with TNF-{alpha} antagonists. Bone marrow edema, which is only detectable with MRI, represents an early sign of inflammation. Therapy with TNF-{alpha} antagonists is based on clinical and laboratory criteria, and signs of inflammation in MRI. MRI is useful for assessment of the ...
On the basis of cylindrical roller thrust bearings it was systematically examined to what extent PVD-coatings are able to take over the function of EP/AW-additives. The bearings were tested under heavy-duty conditions in order to distinguish very fast the efficiency of different coating-substrate-systems. Several coatings were tested for their ability to protect an un-coated counterpart. So just the washers of the roller bearings were coated, the rollers stayed un-coated. Four Me-C:H-coatings showed the best performance and fulfilled the required criterion for roller bearings in the boundary friction: low loss of mass and hardly surface deviation. Material carryover from the carbonaceous coating to the 100Cr6 steel surface was developed by the Me-C:H-coatings during the tests. This mechanism was able to protect the un-coated rollers. Closer investigations were done with an ESMA analysis (electron beam micro range analysis) on ZrC{sub g}-coatings. It could be seen, that a reaction layer ...
On account of a raised appearing of plastic waste and shreddered light fraction (SLF) from old car utilization as well as legal handicaps experiments were carried out at the Institute of Ferrous Metallurgy (RWTH Aachen) on a laboratory rig to inject DSD (Duales System Deutschland)-plastic waste and SLF with the destination of a subsequent raw material utilization in the blast furnace and cupola furnace. The experiments on the laboratory rig with DSD plastics could verify that by injection of specific coal/plastic mixtures into the blast furnace the injection rate could be raised by an improvement in the conversion degree and therefore the amount of the inserted reducing agent can be lowered. The injection of SLF without reduction of the inert materials and of the contents on alloying elements and/or tramp elements by extensive preparation has no advantages according to the experiments for the blast furnace process. Pilot experiments on the cupola furnace showed that, assuming a certain ...
The aim of the presented investigation was to gain information about the behaviour of the initiation and growth of intercrystalline creep cracks during creep deformation from the evaluation of metallographic micrographs. The austenitic steel X10 NiCrAlTi 32 20 HT (Alloy 800 HT) was investigated by carrying out creep tests at 800 and 900 C with different nominal stresses until fracture. Additional tests are carried out on certain creep strains in the late tertiary creep stage. The creep tests are followed by a metallographic investigation of the crept specimens. The statistical distribution of the microcrack lengths was used to estimate the rate of crack initiation and crack growth. It is found that the rate of growth of the intercrystalline creep cracks in Alloy 800 HT is dependent on the applied stress and the creep strain reached. The rate of growth of long cracks was only slightly higher than that of short cracks and was lower than predictions based on fracture mechanics concepts. ...
The influence of a decarburisation process during austenitising of the through-hardenable rolling bearing steel 100Cr6 (SAE 52100) on the rim zone properties of the martensitic through-hardened material was investigated by means of material analysis and diffusion calculations. For this purpose, two specimens were prepared under defined heat treatment conditions, and the near-surface carbon distribution was determined micro-chemically by using secondary ion mass spectrometry (SIMS). In part 1 of the present work, these concentration profiles are compared with the depth variation of the micro-hardness and with the distance curves of the residual stresses and the line broadening ({l_brace}211{r_brace} {alpha}'-Fe diffraction line) both measured by X-ray diffraction (XRD). In addition, microstructure investigations were performed. In part 2, a refined kinetics model of a diffusion-controlled reaction based on the finite element method (FEM) will be applied to the decarburisation ...
Aim: Today, MRI is an integral part of the presurgical evaluation of patients suffering from partial epilepsy. These patients frequently show focal morphological abnormalities with potential epileptogenic character and surgical resection of these lesions is associated with superior postsurgical outcome as to seizure frequency. Apart from easily detectable defects, such as post-traumatic lesions or cerebral infarction, as wide variety of mainly small abnormalities can be detected using MRI. Methods: In this study, 484 patients suffering from partial epilepsy of temporal or frontal onset were evaluated for the incidence of different lesions in this population. Results: All lesions found were included without evaluating their potential epileptogenicity, which remains to be proven using other procedures (EEG, SPECT, PET, etc.). Involvement of the hippocampal formation was a major finding in temporal lobe epilepsy, which could be detected as sclerosis (T2w-images), atrophy (T2w-TSE or ...
The oxidation of boron carbide in steam or air was recently extensively studied especially in Forschungszentrum Karlsruhe, Institut fuer Materialforschung. An important data set is available for the interaction modelling. An oxygen diffusion model through the superficial liquid boron oxide formed on the boron carbide external surface associated to a superficial reaction between the liquid boron oxide and steam is proposed to simulate the experimental kinetics from BOX rig and thermogravimetric tests on the interaction between steam and boron carbide at a temperature range 800 C to 1400 C. The oxygen diffusion model will be also useful to simulate interaction between boron carbide and Ar+O2 (air simulation) atmosphere when the steam pressure becomes zero. From the analysis of BOX rig experimental kinetics of non-condensable (H2, CO2, CO and CH4) gases we propose an oxygen diffusion model through the liquid boron oxide and a ''steam/liquid boron ...
Under the repository storage conditions of Eram and Konrad, waste packages designed for permanent storage must not contain or release freely mobile liquids, except for the minimum residues attainable by reasonable efforts or unavoidable. In accordance with a directive issued by the German Federal Ministry for the Environment (BMU), waste conditioning must be carried out so as to minimize waste volumes and, if possible, on the site where the waste arises. Liquid waste is conditioned most effectively by drying. At the present time, various different processes for drying liquid waste are employed as reflected by the state of the art: The Robe process; roller drying; the RDA process; Favorit; in-drum drying; and HPA liquid waste drying with make-up feed. The HPA process offers these advantages: Drying under atmospheric conditions, which means high level of dryness (freely mobile and releasable water is removed); the residual water content is 10%; isothermal drying by hot air, which ...
Objective: To determine the efficacy of a covered stent prototype designed for protected carotid angioplasty to reduce cerebral embolization. Material and Method: The covered stent tested is made of nitinol, coated with a polyurethane membrane (MembraX{sup TM}; porous size 80 {mu}m). In a bench-top model (flow-rate 650 ml/min, pulsatile flow [dicrote] 123 Pulses/min, pressure 100/60 mm Hg [mean pressure 80 mmHg]) with inserted human carotid (n=6) stent implantation was performed (8/32 mm). Passed particles (mg) were determined in the effluent of a 100 {mu}m filter prior to intervention, after stent deployment and after final dilation (5 mm). Results: When stenting carotid arteries obtained from human cadavers, the highest rate of particle embolization was measured while crossing the lesion with the delivery device (6,8 mg; for all p<0,05), embolization after additional balloon angioplasty and particle rates measured in the effluent filter prior covered stent placement were ...
A working group (SC 45B/WG B8) exists within the international electrochemical commission (IEC) which is working on the combination and revision of the IEC standards 61283, 61323, 61344, 61525 and 61526. All these standards concern direct reading, electronic, personal dose equivalent meters for the quantities H{sub p}(10) and H{sub p}(0,07); they are different with regard to the kind of radiation (photons, and/or beta rays and/or neutrons). The new standard with the number 61526 shall cover the following topics: 1. Combination of all the mentioned standards; 2. Maintenance of the essential requirements of the former standards; 3. Inclusion of the determination of the uncertainty of measurement for the measured dose equivalent value according to the ''Guide to the Expression of Uncertainty in Measurement''; 4. Consideration of all the relevant ISO-standards for reference radiation fields for photon, beta and neutron radiations; 5. Consideration of ...
The aim of this study was to evaluate typical magnetic resonance imaging (MRI) findings in early rheumatic diseases manifesting at the soft tissues of the hand using a retrospective analysis. A total of 186 MRI examinations of patients with clinical suspicion of a rheumatic disease were evaluated in a consensus reading by two experienced radiologists. All imaging patterns were assessed with respect to their type and localization. Under blinded and non-blinded conditions diagnoses were correlated with final clinical diagnosis. The most frequent diagnoses were rheumatoid arthritis (RA, 45.7%) and psoriatic arthritis (PsA, 15.6%). The mean correlation between clinical and MRI diagnosis (r) was 0.75 in blinded and 0.853 in non-blinded reading (p <0.001). The following extra-articular imaging patterns were found: synovitis (59.1%), tendovaginitis (91.4%), dactylitis (14.5%), and bone marrow edema (18.3%). Only dactylitis was specific for a particular rheumatic disease (PsA; r=0.934; ...
From autumn this year, the FRJ-2 of the Research Center Juelich will be supplying molybdenum targets to the Institut National des Radioelements in Fleurus, Belgium - which deals in medical radio-isotopes worldwide - thus helping to meet the need for technetium-99, which is used in the medical profession for diagnostic purposes because of its favourable radiological characteristics. Technetium-99 is formed as a result of the radioactive decay of molybdenum-99. For many years now, molybdenum has been produced by the irradiation of uranium in research reactors, so that the initiation of molybdenum production in the FRJ-2 is not especially new. What is unusual, however, are the particular peripheral conditions which result from the combination of the irradiation requirements, a predetermined target design and the technical characteristics of the reactor and which necessitated special solutions. This applies especially to the handling of the targets after irradiation, which is much more ...
Purpose: To determine the diagnostic value of high resolution MR imaging with a circularly polarised (c.p.) body phased-array coil for the staging of pelvic lymph nodes in cervical carcinoma. Material and methods: 42 patients with histologically proven carcinoma of the cervix were studied on a 1.5 T scanner by using a c.p. body phased-array coil. The imaging protocol included T{sub 2}-weighted turbo-spin-echo (TSE) and T{sub 1}-weighted spin-echo sequences pre and post IV application of Gd-DTPA; slice thickness was 5-7 mm and pixel size 0.53 mm{sup 2}. Lymph nodes with a diameter of {>=}8 mm were considered to have metastatic involvement. MR imaging results were compared with histopathologic findings. Results: MR imaging showed enlarged lymph nodes ({>=} 8 mm) in 16 of 18 patients with histologic proof of lymph node metastases (sensitivity 89%). In 22 of 24 cases MR findings were true negative (specificity 92%). Diagnostic accuracy was 91%. Conclusion: High-resolution MR imaging ...
Purpose: Evaluation of the diagnostic efficacy and cost-benefit of contrast enhanced CT (CT) and MRI pre- and post-SPIO-particles in focal hepatic disease with consideration of therapeutic outcome. Results: In 34/52 (65.4%) of the cases the correct diagnosis was primarily stated by CT (sensitivity [se.] 85.2%, specificity [sp.] 44.0%). In additional 10/52 of the cases unenhanced MRI (se. 91.4%, sp. 75.0%) enabled correct diagnoses, and in another 6 cases the diagnosis was established only by SPIO-MRI (se. 100%, sp. 86.7%). Considering the possible therapeutic recommendation arising from each modality, CT would have induced needless therapy costs of 191,042 DM, unenhanced MRI of 171,035 DM, and SPIO-MRI of 7,311 DM. In comparison to the real therapy costs of 221,873 DM, this would have corresponded to an unnecessary increase of therapy costs of 86.1%, 77.1%, and 3.3%, respectively. In two cases (91 hemangioma, 1 regenerative nodule) all modalities failed, causing unnecessary surgery in ...
The development and improvement of materials plays a key role in energy technology, particularly in power plant technology, because materials are crucial to plant performance and power availability. This becomes particularly clear when one considers that modern power plants generate temperatures of up to 600 C and pressures of up to 230 bar in order to increase process efficiency, conserve resources and reduce CO{sub 2} emissions. Modern heat-resistant materials for power plant technology are customised materials which have been developed to meet the specific requirements of special applications. After the requirement profile has been determined the material is developed or optimised on the basis of previous experiences gained with materials in power plant technology. Basic heat-resistant materials are ferritic materials containing 9 to 12% Cr as well as additions of Mo, V, Nb and W, amongst other elements. Together with the thermomechanical processing, the last-named elements play an ...
CT and MRI of acquired abnormalities of the inner ear and cerebello-pontine angle present themselves with very typical findings. The imaging should be adapted to the pathology looked for and either CT or MRI should be used alone or in combination.CT, especially high resolution CT (HRCT), provides an excellent bone contrast, while MRI has a much superior soft tissue contrast. Acute inflammatory changes of the inner ear are solely depicted by contrast-enhanced MRI. HRCT excellently depicts osseous changes of the inner ear and cerebellopontine angle such as chronic ossifying labyrinthitis occurring after acute labyrinthitis, otosclerotic or traumatic changes. Tumorous changes not yielding to bony changes are best delineated by MRI. Posttraumatic hemorrhage and chronic fibrotic changes within the labyrinth are depicted by MRI, only. In conclusion HRCT and MRI are excellent methods to delineate acquired abnormalities of the inner ear and cerebello-pontine angle. HRCT best depicts osseous ...
The interdiffusion behaviour of MCrAlY-coats on polycrystalline and single-crystalline materials of a similar composition (IN 738 LC/SC 16)shows similar interdiffusion characteristics. TCF-tests, where stress is generated by temperature and sample geometry at the edges of a disk-shaped sample, show that it is possible to differentiate betwee crack resistance of coated and uncoated samples. This method is also suitable for screening tests with different coat thicknesses. Coating of the edge area must, however, be done with great diligence in order to prevent coat thickness variation as results would then not be reproducable. Contrary to TCF (thermal cycle fatigue) TMF-tests (thermal mechanical fatigue)allow to set the stress states that one wishes to test. This method is therefore well suited for testing under operating conditions.(orig.) [German] Im Rahmen dieser Arbeit wurde gezeigt, dass das Interdiffusionsverhalten von MCrAlY-Schichten auf polykristallinen bzw. ...
In this work theoretical investigations are carried out for cooling systems, which are used in fuel cell vehicles. This work focuses mainly on the capability of increasing the heat rejection rate by using new alternative cooling systems and by improving the conventional cooling system. Fuel cell vehicles have a higher demand of heat rejection to the ambient than comparable vehicles with combustion engine. The performance of conventional liquid cooling systems, especially at high loads and high ambient temperatures, is often not sufficient anymore. Hence, cooling systems with improved performance are necessary for fuel cell vehicles. The investigations in this work are based on DaimlerChrysler's ''A-Class'' having a PEM-Fuel Cell system integrated. Specific computational models are developed for radiators and condensers to evaluate the performance of different cooling concepts. The models are validated with experimental data. Based on an ...
The deep borehole heat exchanger (BHE) of Weggis is operational since 1994. During the years 1995 to 2000 the BHE has produced for both, direct heating and as a source for the heat pumps, a yearly amount of heat of 220 MWh. The share of direct heating has been more than 60%. The global average power delivered to all consumers has been about 100 kW. This has yielded to a mean source temperature out of the deep BHE of 40.5 {sup o}C and to a mean return temperature of 33.3 {sup o}C. During the years 2000 and 2001 three additional multi-family dwellings have been connected as heat consumers to the BHE. The amount of delivered heat has nearly been doubled (from 220 to 440 MWh per year) as well as the nominal load. This has induced a small reduction of the delivery temperature and a significant reduction of the return temperature to the BHE (37.2 {sup o}C and 29.9 {sup o}C respectively). As a result, the direct heating share has been reduced to 8%. The seasonal performance factor has changed ...
The ERICAM model (Environmental Risk Internalization through Capital Markets) includes the capital markets as a source contributing to the coverage of risks due to nuclear activites, thus enhancing the effectiveness and functions of the nuclear liability law. The model proposed will allow higher amounts for compensation and will increase financial security, flow of information, and efficient use of resources. The implementation of the model can be achieved on the financing side by issuing Nuke bonds, linking accident-specific options to government bonds. This will essentially increase the risk coverage compared to present means, and will be a pin-pointed addition to the existing layer system. There are three institutions proposed to act as mediators in the implementation of the model: A government authority to supervise the trade in Nuke bonds. Risk-bearing associations in oder to enhance the model`s efficiency, and to reduce transaction costs. Rating agencies that will reduce the ...
The present publication is based on facts, data, knowledge and projects, which have been incorporated in the development of an energy concept for the district Schmalkalden-Meiningen. The energy concept of a district is a concept oriented at action on and realisation of mid-term and long term decisions in the fields of energy policy, economy and ecology, which must be taken by municipal and economic decision-making bodies. The energy concept accords with the targets of the Agenda 21, the environmental targets of the Federal Republic of Germany and of the Land Thuringia. Accepting this energy concept the district Schmalkalden-Meiningen shows its willingness to contribute to a lasting development in all fields of economy and ecology and thus does justice to its increasing responsibility. (orig.) [German] Die vorliegende Veroeffentlichung baut auf Fakten, Daten, Erkenntnissen und Projekten auf, die in die Erarbeitung des Energiekonzeptes fuer den Landkreis Schmalkalden-Meiningen ...
An important opportunity for solving future traffic problems lies in a change of the connection existing between traffic growth and economic development. It could help bring about a cut in traffic intensity. This can be achieved by rationalizing transport processes, i.e. by enhancing the efficiency of traffic via improved organization and infrastructure. Rationalization means that a given traffic effort (distance in kilometres, time, route, energy) can yield a higher transport effect, or a certain transport effect can be attained with less traffic effort. Enhanced productivity permits more transport without more traffic-related and environmental nuisances. (orig.) [Deutsch] Ein wichtiger Weg zur Loesung der kuenftigen Verkehrsprobleme liegt in der Veraenderung des Zusammenhangs der zwischen Verkehrswachstum und Wirtschaftsentwicklung besteht. Damit koennte eine Senkung der Transportintensitaet erreicht werden. Ein Ansatz hierzu bietet die Rationalisierung der ...
The thesis explains the development of a mass spectrometerical isotope dilution analysis (MS/DA) for determining trace amounts of Tc. The Tc-97 isotope has been prepared by in-core irradiation of Ru of natural isotopic composition, and used as the indicator isotope. For separation of Tc-97 from the Ru matrix, a method has been developed to quantitatively separate Tc-97 from a high Ru surplus. For determining the isotope ratio for the MS/DA, a mass spectrometrical measuring technique has been found which allows reproducible measurement of the Tc-99/Tc-97 isotope ratio. Positive and, for the first time, also negative thermoionisation has been used as a method of selective ionisation of Tc. The applicability of the MS/DA for Tc trace analysis has been verified using two Al foils doped with Tc-99 or Mo-98, respectively. These have been irradiated in a nuclear reactor, the irradiation of Tc-99 yielding Ru-100, and irradiation of Mo-98 Tc-99. The determination of the elements Ru and Mo in ...
A phenomenological model of the heat transfer in direct injection diesel engines was developed. Utilizing the thermodynamic results of a combustion model as an input, the model is able to predict the temporal variation of the heat losses from the cylinder gas to the cylinder walls. Additionally, the division into isothermal combustion chamber subsurfaces allows the consideration of the spatial variation of the wall heat fluxes. The physical mechanisms such as flow dependent convection, heat radiation due to hot soot particles and isolation effects of deposited soot layers are described in detail. Thus the effects of these mechanisms on the overall heat transfer can be studied. The heat transfer model was verified successfully by the comparison to measured wall heat fluxes in a single-cylinder direct injection diesel engine. It is shown that the effects of engine speed and load, turbocharging and soot deposition can be predicted with good accuracy. [German] Es wurde ein ...
Compared to the reference year of 1990, CO{sub 2} emissions of the Federal Republic of Germany have been curbed by about 12%, primarily as a result of industrial backfitting and pollution abatement measures accomplished in the industrial infrastructure of the new Federal Laender of Germany. Federal Government policy sticks to the previous commitment, to reduce carbon dioxide emissions by 25% by the year 2005. Current forecasts and scenarios of future greenhouse gas emissions show that only immediate adherence to a very stringent reduction policy might ensure that this ambitious goal will be achieved. In this context, any change of the baseline data and scenarios hitherto used for progonostic assessments is a crucial factor, so that the article here discusses the impacts of a change in the nuclear generation scenario, as recently ventilated by the German Federal Government, and expected effects on public power supply. (orig./CB) [Deutsch] Ausgehend von dem Bezugsjahr 1990 sind die ...
The spent fuel management concept of direct ultimate disposal is compatible in its fundamental features with the law of the European Community. This applies to a national law prohibiting spent fuel reprocessing and the handling of plutonium in Germany, imposing restrictions on exporting spent fuel assemblies and importing plutonium and reprocessing remnants, and on power plant operators to employ reprocessing services abroad. Also, a nuclear power phase-out decided by the German government would in principle not mean a breach of the EURATOM treaty. (orig./HP) [Deutsch] Als Alternative zur geltenden Rechtslage werden im Deutschen Rundestag Aenderungen vorgeschlagen, die das Entsorgungskonzept der direkten Endlagerung - d.h. ein Verbot der Wiederaufarbeitung von Brennelementen aus deutschen Kernkraftwerken auch im europaeischen Ausland - vorschreiben und einen ``Ausstieg`` aus der Kernenergienutzung anordnen. Vor dem Hintergrund einer Analyse der tatsaechlichen ...
About 25 years after the last edification of a new large high voltage institute at Technical University of Karlsruhe and about 10 years afte the edification of the test lab at Kaiserslautern University, the Brandenburg Technical University of Cottbus had the opportunity to design new high voltage test facilities from the very beginning on and to realize it in a very short time. To review the project from the first ideas followed by the planning and realization phase and the final commissioning of the technical equipment, this book should be a contribution to spred the experiences made among interested people and to demonstrate the actual technical possibilities. To ensure an international exchange of these experiences, all co-authors to the trouble to translate their participation's also to the English language. (orig.) [German] Etwa 25 Jahre nach dem letzten grossen hochspannungstechnischen Institutsneubau in der deutschen Hochschullandschaft an der TH Karlsruhe, bzw. 10 ...
In 1991/1992, VEAG decided to convert its 500 MW plants at Jaenschwalde and Boxberg to the latest state of technology. This even included the discharge of the cleaned flue gas through the existing cooling towers. The site of the flue gas desulphurization plant and also the existing cooling tower shells required routeing of the clean gas lines similar to the routes in the existing plants of RWE. The positive experience accrued with the pipework material `glass-fibre reinforced vinyl ester resin` has also led to the selection of this material here. The universally positive experience gained from existing clean gas lines via cooling towers by very different power station operators induced VEAG and its partners also to equip new construction operations in the new Federal states with this technology. (orig.) [Deutsch] In den Jahren 1991/1992 entschloss sich die VEAG, ihre 500-MW-Anlagen Jaenschwalde und Boxberg auf den neuesten Stand der Technik umzuruesten. Hierzu gehoerte auch die ...
56 patients with the clinical diagnosis of sprained ankles were investigated. Evaluation of the anterior (AFTL) and posterior fibulotalar ligament (PFTL) was performed with the foot in dorsiflexion (20 ) and of the fibulo calcanear ligament (FCL) in plantarflexion (45 ). Axial T{sub 1}w-SE and T{sub 2}w-TSE images were obtained. Full-length visualisation of ligmaments in one slice and the extent of injury were evaluated. 12 ankle injuries were confirmed by operation. With MRI full-length visualisation of lateral ankle ligaments was possible in 86%. A partial/complete rupture of the AFTL was noticed in 33/64% and of the FCI in 29/39%, and of the PFTL in 27/5%. Sensitivity/specificity of MRI when compared to surgery was 100/100% for injuries of the AFTL, 64/100% for the FCL, and 33/78% for the PFTL. (orig./MG) [Deutsch] 56 Patienten wurden mit der klinischen Diagnose einer frischen Supinationsverletzung des oberen Sprunggelenkes untersucht. Das Lig. talofibulare anterius (TFA) und ...
Smooth and notched specimens of the bearing steel 100Cr6 (SAE 52100) in a bainitic condition were used to determine the S-N curves under tensile, torsional and combined in- and out-of-phase loading. In the area of high-cycle fatigue, crack initiation was most likely caused by inclusions like Titanium Carbonnitrides or Aluminium Oxides. A micro mechanical model for the crack initiation by inclusions was developed. Another model was developed to describe the influence of these inclusions on the lifetime. A weakest-link model, using the statistical distribution of inclusions and surface flaws, was used to describe the endurance limit. (orig.) [German] Es wurden Woehlerlinien unter Zug-Druck-, Torsions- sowie kombinierter phasengleicher und phasenverschobener Zug-Druck- und Torsionsbelastung fuer glatte und gekerbte Proben des Stahls 100Cr6 (SAE 52100) im bainitischen Zustand erstellt. Im Bereich der Langzeitermuedung gingen die Risse meistens von nichtmetallischen Einschluessen ...
The aim of this work was to develop a method to distinguish between different ion formation processes and to determine the influence of these processes on the total number of detected monatomic ions of a certain element. A vector/matrix-formalism was developed, which describes the physical processes of sputtering, ion formation, mass separation and detection in laser-SNMS. In the framework of the method developed, based on this theoretic formalism, changes in the secondary flux contribution of the respective element were observed by comparing the detected monatomic ion yield obtained in specifically aligned (SIMS and) laser-SNMS experiments. The yields resulting from these experiments were used to calculate characteristic numbers to compare the flux composition from different surfaces. The potential of the method was demonstrated for the elements boron, iron and gadolinium by investigating the changes in the flux composition of secondary particles sputtered from metallic surfaces, as a ...
Isothermal reaction experiments were performed in the temperature range of 1000 - 1300 C in order to determine the chemical interactions between Zircaloy-4 fuel rod cladding and Inconel-718 spacer grids of Pressurized Water Reactors (PWR) under severe accident conditions. It was not possible to apply even higher temperatures since fast and complete liquefaction of the components occurred as a result of eutectic interactions during heatup. The liquid reaction products formed enhance and accelerate the degradation of the material couples and the fuel elements, respectively. Only small amounts of Inconel are necessary to liquefy large amounts of Zircaloy. Thin oxide layers on the Zircaloy surface delay the beginning of the chemical interactions with Inconel but cannot prevent them. In this work the reaction kinetics have been determined for the system: as-received and pre-oxidized Zircaloy-4/Inconel 718. The interactions can be described by parabolic rate laws; the Arrhenius equations for ...
High-strength, fully hardening steels are used in general for applications involving severe wear and frequently also additional cyclic stress. For the latter condition, the available information and experimental data for component dimensioning are insufficient. Work reported in the dissertation therefore was intended to establish experimental information showing the performance of the bainitic roller bearing steel 100Cr6 and deducing rules of applicability to components, of the fatigue strength data obtained with the specimens. Various models for calculating the fatigue strength are presented together with their application to the steel 100Cr6. The results show that the weakest link model is a good concept for fatigue strength calculation, taking into account multiaxial loading. (orig/CB) [Deutsch] Hochfeste durchhaertende Staehle unterliegen in der Regel hohen Verschleissbeanspruchungen und werden darueber hinaus oftmals zusaetzlich schwingend beansprucht. Fuer die schwingende ...
Wood is currently having a renaissance as a domestic fuel. Wood pellets, usually about 8 mm in diameter and 40 mm long and produced from sawmill and wood processing residues by pressing without binders, are gaining general acceptance. According to a market analysis of Solar Promotion GmbH, Pforzheim, about 4,800 pellet-fuelled heating systems with automatic fuel supply and with a total thermal capacity of 35 kW are in operation in Germany, and 2000 new ones were installed in 2000. [German] Holz als Brennstoff erlebt in vielen Heizkellern und Kaminen eine Renaissance. Und zwar nicht in Form von Holzscheiten, sondern als kleine Presslinge, meist mit einem Durchmesser von acht und einer Laenge von bis zu 40 Millimetern. Als Abfallprodukt von Saegewerken und Holz verarbeitenden Betrieben werden die so genannten Pellets unter hohem Druck und ohne Bindemittel wie beispielsweise Leim hergestellt. Und dieser neue Brennstoff findet immer mehr Anhaenger. So sind im vergangenen Jahr nach einer ...
Many industrial workshops in Germany were erected during the 40s and 50s, especially at the beginning of the economic boom. After more than 40 years, these facilities are in need of structural and production-technical modernization. A case in point is the carriage fabrication workshop of the Salzgitter-based company Linke-Hoffmann-Busch. The characteristic features of this type of building are large glazed areas, free uncontrolled ventilation and substantial height. Opportunities for energy-oriented and light-technical modernization are demonstrated at this Salzgitter workshop in exemplary form, the emphasis being on the use of solar energy components and, particularly, transparent thermal insulation. (orig.) [Deutsch] In der Bundesrepublik Deutschland gibt es viele Produktionshallen, die in den vierziger und fuenfziger Jahren, insbesondere zu Beginn des wirtschaftlichen Aufschwungs, errichtet wurden. Diese Hallen sind nach ueber vierzig Jahren sowohl aus baulichen als auch ...
The exactness of the best atomic clocks currently shows a temporal variation of 1 second in 30 million years. This means that we have reached the point of the most exact frequency and time measurement ever. In the past, there was a trend towards increasing the exactness in an increasingly fast sequence. Will this trend continue? And who will profit from it? This article is meant to give answers to these questions. This is done by presenting first the level reached currently with the best atomic clocks and describing the research activities running worldwide with the aim of achieving even more exact clocks. In the second part, we present examples of various areas of technical subjects and research in which the most exact clocks are being applied presently and even more exact ones will be needed in the future. [German] Die Genauigkeit der derzeit besten Atomuhren entspricht einer Sekunde Unsicherheit in 30 Millionen Jahren. Damit erlauben Frequenz- und Zeitmessungen die genauesten ...
In a prospective study 102 patients with malignant tumors of the tongue, oropharynx, hypopharynx, and larynx were staged by means of MRI. Special attention was directed at those tumour extensions that could influence the treatment strategy. The MR findings were correlated with the results of palpation, endoscopy, ultrasound, computerised tomography and histopathological findings. MRI showed a good delineation of pT{sub 2} to pT{sub 4} tumours. However, visualisation of small tumours in the soft palate, the tonsils, the pyriform sinuses and vocal cords was difficult. In conclusion our results suggest that in addition to endoscopy MRI is a valuable tool for the examination of tumours of tongue, oropharynx, hypopharynx and larynx. (orig.) [Deutsch] In einer prospektiven Studie wurden 102 Patienten mit malignen Tumoren der Mundhoehle, des Oro- und Hypopharynx sowie des Larynx mit der Mgnetresonanztomographie (MRT) untersucht, wobei besonders Wert auf die Bestimmung derjenigen ...
As a financial institution o the European Union, The European Investment Bank is working and to add substance to the commitments made by the Union and its Member States at Kyoto and subsequently at Johannesburg. Over the last two years, renewable energy sources have attracted funding of more than 1.1 billion from the bank, equivalent to 14% of the total loans granted to the energy sector 7.8 billion), compared to an average o 7.9 % over the previous five years. In order to obviate the detrimental characteristics presented by these investments from a financial viewpoint, in March, 2004 the bank set up a 'CCFF' (Climate Change Financing Facility) of 500 million. Additionally, along with the other financial institutions, the EIB is looking into he possibility of supporting the establishment of European carbon credit trading hubs. Where the economic assessment of these projects is concerned, the bank has decided to take account of external environmental and technological ...
A study conducted at the IHS had the aim to obtain basic information on whether it is possible to build flow turbines following the free jet principle that are on a par with, or superior to, the conventional design, especially in terms of performance and the efficiency curve. Several inflow contours with a ventilated free jet and a conventional flow turbine were studied. The direct comparison of these variants revealed a slightly enhanced peak load efficiency and a very distinct superiority of the free jet contour during partial load. But the efficiency of all variants failed to attain the values claimed by commercial manufacturers. As compared to the initial contour, peak load efficiency was enhanced by 5 per cent. During partial load, the variants studied showed a distinct superiority of the free jet concept over the contour of conventional flow turbines. (orig.) [Deutsch] Am IHS wurde eine Untersuchung mit dem Ziel durchgefuehrt, grundlegende Aussagen zu gewinnen, ob ...
The research project's objective is to create a decision help for owners of residential buildings for several families regarding the renewal of decentralized heating and warm water preparation systems in the flats. The focus lies on a comparison of the costs of typical systems on the basis of a full cost calculation. This is done by taking into consideration the intentions of residential building companies like the reduction of additional costs to be paid by the tenants (both for social reasons and to make the flats easier to rent), low investment costs, low maintenance costs, energy saving, tenants' claims for comfort and acceptance by the tenants, economical reasons, especially regarding flats fully amortized (activation in the balance sheet). In addition to the quantitative comparison, the advantages and disadvantages of the different systems were also compared to one another from the qualitative point of view. [German] Ziel des Forschungsvorhabens ist die ...
The objective of the project was to develop an infiltration material based on SiC that should have improved corrosion resistance and should permit higher operating temperatures. From a variety of tested doping agents, zirconium silicide and molybdenum proved to be the most appropriate agents. The respective infiltration materials permit a combination of advantages of the SSiC with those of the SiSiC. Silicide SiC, analogous to the SiSiC, is almost nonshrinking, and above all is more corrosion-resistant than SiSiC in the alkaline regime, due to the replacement of free silicon by silicide phases. The operating temperature of the molybdenum-base variant is 1600 C. (orig./CB) [Deutsch] Ziel des Vorhabens war die Entwicklung eines Infiltrationswerkstoffes auf SiC-Basis mit verbesserter Korrosionsbestaendigkeit und hoeherer Einsatztemperatur. Aus einer Vielzahl von getesteten Dotierungsmoeglichkeiten kristallisierten sich Zirkondisilicid und Molybdaen als geeingete Zusaetze heraus. Die ...
The laser grooved buried grid (LGBG) cell was developed at the University of New South Wales, Australia. The enormous advantage of the Saturn technology is the simple formation of a selective emitter via two step diffusion, which is optimised on the surface for the charge carrier generation and under the metal grid for contact formation. The reflection losses due to shading are simultaneously minimised by the installation of the contacts at right angles in the wafer surface. Due to the increased infeed compensation, particularly the compensation covering the costs, the economic importance of the energy yield of a PV plant is growing. Ultimately, it is not just the installed output (KWp) that matters to the customer, but increasingly the specific yield (kWh/kWp). An increased energy yield with optimally matched components with the Saturn technology means high annual compensation, which in turn shortens the amortisation period. [Deutsch] Die LGBG-Zelle wurde an der Universitaet von New ...
In the group of persistent aromatic hydrocarbons, the highest values were determined for polychlorinated biphenyls (PCB), total DDT and hexachlorobenzene (HBC). Comparisons of the relevant median values for the past six years led to the conclusion that the steep initial decline in the breast milk concentrations of DDT and HBC was followed by reductions at a much lower pace in the years after 1987. The time course of the concentration of the total PCB did not appear to follow any particular pattern. The mean contents of lead and cadmium remained by a wide margin below the threshold values for these heavy metals and thus were of no relevance from the toxicological point of view. It was found that the 134 and 137 cesium isotopes constituted no particular health hazard for breast-fed infants, as the relevant concentrations in breast milk were low. (VHE) [Deutsch] In der Gruppe der persistenten Chlorkohlenwasserstoffe werden die hoechsten Konzentrationen bei den ...
In coke-oven operations flue-gas valves are used to switch the regenerator function from rich gas firing to lean gas firing. Compared with the simple geometry of the other parts of the flow path, which comprise flues and regenerators, the narrow and winding passages of the flue-gas valves give rise to relatively high losses in pressure. Without the construction of high (and therefore expensive) chimneys, this means that operating problems may well arise due the inadequate suction capacity. The project focused on the theoretical and experimental analysis of a coke-oven flue-gas valve. The primary aim was to reduce the pressure drop through the valve without modifying its external geomerty. The internal flow characteristics created by different valve geometries under a variety of operating conditions were simulated using the commercial CFD code Fluent/UNS, which provided velocity and pressure distributions. A half-scale model valve was constructed in order to characterise the internal ...
Modern commercial alloys are not suited for future steam turbines of operating temperatures beyond 700 C. {gamma}'-hardened alloys like Waspaloy have good mechanical characteristics but have defects when large batches are melted. {gamma}'/{gamma}''-hardened alloys like Inconel 706, on the other hand, are easy to produce but have insufficient microstructural long-term stability and insufficient creep strength. Mixed crystal solidified alloys like Inconel 617 have excessive yield stress at forging temperatures. Two new alloys were therefore developed. Results so far show that they have good production characteristics but insufficient mechanical characteristics. The reasons for this are currently under investigation. (orig.) [German] Die heutigen kommerziellen Legierungen sind nicht geeignet fuer den Einsatz in zukuenftigen Dampfturbinen mit Betriebstemperaturen oberhalb 700 C. {gamma}'-gehaertete Legierungen wie Waspaloy zeigen zwar gute ...
Processing certain raw materials containing natural radioactive isotopes (e.g. U-238, Th-232 or K- 40) into products such as glas, abrasives, grinding materials or electrodes used for gasshielded tungsten-arc welding also leads to certain concentrations of industrial waste containing natural radioactive materials. Such industrial waste does not necessarily contain natural radioactive substances in concentrations exceeding the highest possible levels but nevertheless in significantly measurable quantities. This, however, frequently leads to confusion bordering on irritation by entities processing such substances as well as the general public, since they tend to believe natural radioactive substances in unobjectable concentration to cause similar or identical - health - consequences as man made radioactive substances in detrimental concentration. Radioactive materials may be incorporated intentionally or unintentionally into the product as main or additional ingredients. The recent ...
A numeric method for predicting mineral ash deposition in coal dust furnaces is presented which is based on a bidirectional working time coupling of thermodynamic calculation routines (ChemApp{sup TM}) with the commercial CFD code FLUENT{sup TM}. The deposition characteristics of particles and wall surfaces is assessed on the basis of evaluations of flow simulation parameters and results of thermodynamic calculations for the mineral matter contained in the fuel particles, taking into account the complete energy, momentum and mass exchange history of the ash and the mineral conversion. The models enables calculations of the gaseous release of mineral components (e.g. alkaline substances and chlorine) from ash during combustion and its distribution inside a combustion chamber. The method and model are validated using experimental data. (orig.) [German] In der vorliegenden Arbeit wird ein numerisches Verfahren beschrieben, mit dem die Ansatzbildung in Kohlestaubfeuerungen praediktiv ...
The aim of this study was to qualitatively and quantitatively study MR artifacts of various stents on the basis of in vitro experiments. We were particularly interested whether sequence type and orientation of the stent with respect to the static magnetic field influences the artifact. We examined 18 stents of different material (nitinol, stainless steel, cobalt alloy), different design of the stent meshes (AccuLink, OmniLink, DynaLink, Xact, Protoge, Wallstent Monorail), different diameter (5-10 mm) and different length (18-58 mm) with a turbo spin echo (TSE), a 2D-fast low angle shot (FLASH) and a 3D-FLASH sequence. The MR images were examined qualitatively with respect to possible artifacts. Furthermore we examined the MR data quantitatively: The contrast-noise-ratio (CNR) was determined both within the stent and outside (within the tube); based on these values we calculated the transparency factor P, furthermore we calculated the apparent vascular lumen within the tube and within ...
Purpose: To evaluate MR artifacts of carotid artery stents and to optimize stent properties and sequence parameters. Material and Methods: Four carotid artery stents - Wallstent (mediloy), Precise (nitinol), ACCULINK (nitinol) and a stent prototype (nitinol) - were investigated in a flow model of the cervical vessels. The model was made of silicon tubing and a flow pump that produces realistic flow curves of the carotid artery. To investigate the effects of magnetic susceptibility and radiofrequency induced shielding artifacts, turbo spin echo and gradient echo sequences as well as CE-MRAs were measured. To improve the visualization of the stent lumen in a CE-MRA, flip angle as well as geometry and covering of the stent prototype were altered. Results: Susceptibility artifacts in stents of the carotid artery only influence the lumen visualization at the proximal and distal end of the braided mediloy stent. A change of stent coverings has no significant influence on radiofrequency ...
The purpose of the present study was to examine reactions between bromium atoms with {alpha}, {beta}-unsaturated carbonyls. Acrolein, methacrolein, and methyl vinyl zetone were chosen as representatives of this family. The latter two compounds, beside formaldehyde, belong to the main products of atmospheric oxidation of isoprene and have been detected in the troposphere at concentrations of up to almost 1 ppb. It is known that alkenes react with bromium via addition to form an instable adduct. This product can either decompose again into its educts or react with molecular oxygen. The aim of the study was to determine the velocities of the reactions between the three {alpha}, {beta}-unsaturated carbonyls and bromium and to clarify the involved reaction mechanisms by means of kinetic experiments and product analyses. (orig./SR) [Deutsch] In dieser Arbeit wurde die Reaktion von Bromatomen mit {alpha}, {beta}-ungesaettigten Carbonylen untersucht. Ausgewaehlt wurden Acrolein als einfachster ...
CNG vehicles suffer from an uncontrolled temperature rise of the gas inside the tank during the filling process and heat exchange with the environment leads to variable filling levels. A partly filled tank reduces the range of CNG vehicles and works as a impediment to the spreading of environmentaly more friendly CNG vehicles. The increase of the pressure inside the tank combined with a prolongation of the filling time beyond three minutes can reduce the deficit of the filling process. For economic reasons the time required for refuelling should be as short as possible without the need to operate the filling station with a critical pressure. To meet this target the current technique requires further improvement. (orig.) [Deutsch] Die betriebliche Praxis bei Tankvorgaengen von Erdgasfahrzeugen zeigt, dass waehrend des Tankvorganges die Temperatur des getankten Erdgases im Fahrzeugtank ansteigt. Waehrend und nach Beendigung des Tankvorganges findet ein ...
Molybdenum is an essential element for living organisms. Moreover its radionuclides may represent an incorporation risk for members of the public and/or radiation workers after a nuclear accident or a release of radioactive materials. However, only few reliable data on Mo biokinetics in humans were available. The results of recent tracer kinetic investigations with stable isotopes have shown several differences from the ICRP data with regard to the processes of intestinal absorption and of excretion. As a consequence, the dose coefficients calculated with a revised biokinetic model deviate from the ICRP estimates. By ingestion of {sup 99}Mo radionuclides with solid food, for example, the dose to the colon may be higher of a factor up to 1 order of magnitude, due to the fraction of non-absorbed material which traverses the gastro-intestinal tract. (orig.) [Deutsch] Molybdaen ist einerseits ein fuer Lebewesen essentielles Spurenelement, andererseits koennen radioaktive Mo-Isotope im ...
For the transformation of gasoline direct injection concepts into production solutions not only fuel economy and emission potential but also system stability and durability is important as well as the optimized interaction with exhaust gas aftertreatment and engine management. By application of optical diagnostic methods on research engines and especially in real multicylinder engines, a DI gasoline combustion system could be developed meeting all these requirements. Its fuel economy in the lower part load range is found within the scatterband of DI-Diesel engines. Special emphasis has been concentrated on the optimum adaptation of the combustion system to the limited exhaust gas temperature range of the NOx storage catalyst technology. A combination of this DI gasoline concept with turbocharging reveals a high potential especially regarding transient response. (orig.) [Deutsch] Bei der Ueberfuehrung von Direkteinspritzkonzepten in reale Serienloesungen sind nicht ...
The composition of alkaline and neutral boric acid containing evaporator concentrates resulting from the treatment of radioactive waste water in nuclear power plants with WWER reactors is described as well as the processing of these concentrates to a product suitable for final disposal. Tests with mock solutions of these evaporator concentrates have been performed at the laboratory and teststand scale to produce a dry residue by continuous thickening, which can be processed into a highly leach resistant product, suitable for final disposal, by cementation. Ca-compounds must be added to the evaporator concentrates prior to the drying in an rotary thin-film evaporator (RTFE). The tests showed that neutral evaporator concentrates can be dried in a RTFE with addition of small amounts of Ca-compounds. The alkaline evaporator concentrates with high boric acid and total salt load require a multiple amount of Ca-compounds and diluting water to perform the drying process. A brief description of ...
The Nuclear Renaissance is stumbling at the very same time it should speed up in order to help control the climate change and meet a fast growing energy need in a large part of the world. Rising costs of projects, uncertainties about their completion, rocketing safety requirements, and financial constraints are key factors which slow down the Nuclear Renaissance. Furthermore, the legal infrastructure required from any country to enter a commercial nuclear programme (safety authorities, fuel cycle, and waste disposal) is a major hurdle s which impedes consideration for small to mid size reactors, well suited for many countries. The paper prepared and presented by Alain Bugat (Chairman of NucAdvisor and former Head of the French Atomic Energy Commission), Dominique Vignon (CEO of NucAdvisor and former President and CEO of AREVA NP) and Michel Lecomte (Co-founder NucAdvisor) reviews the present status of the Nuclear Renaissance. Based on an analysis of initial versus actual plans for all ...
Stabilized austenitic steels can suffer intercrystalline stress corrosion cracking under BWR water conditions. This experience of the last three years, which is important for German nuclear power station technology, has resulted from the discovery of cracks, which were detected in pipework made from titanium-stabilized 1.4541 charged with hot reactor water in six boiling water reactors and in core components made from niobium-stabilized 1.4550 of one BWR plant. Remedies to the pipework have been found by applying optimized materials and fabrication procedures and also by improving water chemistry conditions. (orig.) [Deutsch] Stabilisierte austenitische Staehle koennen unter SWR-Reaktorwasser-Bedingungen interkristalline Spannungsrisskorrosion (IKSpRK) erleiden. Diese fuer die deutsche Kernkraftwerkstechnik bedeutsame Erfahrung der letzten drei Jahre ergab sich aus Rissbefunden, die in mit heissem Reaktorwasser beaufschlagten Rohrleitungen aus dem Ti-stabilisierten 1.4541 von sechs ...
Long duration investigations on XLPE-insulated, medium-voltage cable have been intensively carried out by producers, institutes and users for decades. These tests have concentrated on cable ageing especially under the influence of water. About six years ago, a standard test procedure was developed based on comprehensive know-how. This test procedure is now included in DIN VDE 0276-620. In the following text, experience gained during testing and while performing tests in numerous laboratories is reported, and a summary of the test results is given. (orig.) [Deutsch] Langzeituntersuchungen an VPE-isolierten Mittelspannungskabeln, die sich mit der Alterung der Kabel, besonders unter dem Einfluss von Wasser beschaeftigen, wurden seit Jahrzehnten durch Hersteller, Institute und Anwender intensiv betrieben. Basierend auf diesem sehr umfangreichen Know-how wurde vor rd. sechs Jahren ein standardisiertes Pruefverfahren entwickelt, das heute Bestandteil der DIN VDE 0276-620 ist. Die Verfasser ...
In early March, 2000 a modern electron-beam welding facility for both series and one-off production of valves bodies (500 kg, up to 50 mm wall thickness) was commissioned at Josch Strahlschweisstechnik. Welding is performed under a fine vacuum. This permits not only the welding of components subject to acceptance inspection (HP0 approval), but also of special materials such as titanium, molybdenum, tungsten, Hastelloy and copper, and also their pairings. Products are developed and readied for production using modern 3D CAD software. A modern nine-axis control system makes it possible to produce sockets in pipe-on-pipe joints. (orig.) [German] Anfang Maerz 2000 wurde eine moderne Elektronenstrahlschweissanlage fuer die Herstellung von Armaturengehaeusen in Grossserien oder auch fuer Einzelfertigung (500 kg, bis 50 mm Wanddicke) bei der Josch Strahlschweisstechnik in Betrieb genommen. Die Schweissungen erfolgen im Feinvakuum. Somit koennen neben dem Schweissen ...
The topics of these short lectures on the subject of cyclic stress were: Microstructural mechanisms of damage accumulation under a multistage cyclic stress until incipient cracking; influence of surface decarbonizing phenomena on the failure behaviour of steel construction parts subjected to cyclic stress; thermocyclic fatigue of pipe samples of austenitic steel 1.4436; studies on surface structuring, microstructure and fatigue in LCF area. The short lectures on effects of quasi-static and creep stress were: Shear fracture in AlMg alloys as a result of local plastic instability; study of formation and growth of pores for an early recognition of damage and the course of damage in heat-resistant steels under creep test; experimental and numeric studies of the infuence of the microstructure on the course of damage during shear fractures of steel; numerical modelling of ductile fractures on the basis of micromechanical models. Under the topic of tribological stress the following lectures ...
Magnetic resonance imaging (MRI) in stroke makes it possible to visualize the initial infarct in cases of acute cerebral ischemia. Perfusion MRI serves to determine which tissues are additionally at risk of infarction due to persistent hypoperfusion. MRI also allows those examiners with limited experience to reliably confirm an infarct. The most important differential diagnosis of cerebral ischemia, intracerebral hemorrhage, can likewise be recognized with certainty using MRI. Although diffusion and perfusion MRI only demonstrate the pathophysiology of cerebral ischemia approximately, the method is suited for identifying those patients who would profit from reperfusion therapy. Whether MRI is also appropriate as an aid to reaching a prognosis on the risk of secondary hemorrhage has not yet been resolved. (orig.) [German] Die Schlaganfall-MRT ermoeglicht es, bei akuter zerebraler Ischaemie den bereits initial entstandenen Infarkt darzustellen. Mittels Perfusions-MRT ...
Following the conventional X-ray diagnosis of the skull and upper cervical spine, CT proved to be the primary diagnostic method after a skull and brain injury: For all 4 cases we succeeded in detecting the occipital condyle fracture and in determing its size and location by reconstructions (coronal, sagittal, 3-D). In the case of complex occompanying injuries like soft tissue hematomas (cerebral, in the spinal cord, and the soft tissue of the neck) or for the detection of brain stem contusion, MRT had significant advantages. MRT can offer a higher image quality in soft tissue, especially in the spinal cord and the brain. (orig.) [Deutsch] Im Anschluss an die konventionelle Roentgendiagnostik des Schaedels und der Halswirbelsaeule, erwies sich die Computertomographie als primaer einzusetzendes diagnostisches Verfahren, nach erlittenem Schaedel-Hirn-Trauma. In allen Faellen gelang der exakte Frakturnachweis an den Okzipitalkondylen, die Bestimmung des Frakturausmasses und die genaue ...
The results of the creep performance studies at temperatures from 700-1000 C with welds of alloy 800 HT, the manual shielded metal arc welds made with Githerm 85 and Grini 209 filler metals, as well as the MIG pulsed arc welds made with the Nicrofer S 206 and Nicrofer S 5520 filler metals, proved to be in very good agreement with the calculated characteristic values published on VdTUeV sheet 434 in comparative assessments based on creep values valid for a service period of 10 000 hours. The MIG pulsed arc weld made with the Nicrofer S 5520 filler metal achieved by far the best results and strength values comparable to those of the base material, whereas the values of the other welds were corresponding to calculated strength values of the base material reduced by 20%. (orig./CB) [Deutsch] Die im Temperaturbereich von 700-1000 C an Alloy 800 HT und den Elektrodenhandschweissverbindungen mit den Schweisszusaetzen Gritherm 85 und Grini 209, sowie den MIG-Pulsed-Arc-Schweissungen mit den ...
The procedure for field corrosion tests in sea water is decribed in DIN 50 917, Part II. Distinction is made thereby between long-term undisturbed test specimens, which remain at the exposure site up to the time of sampling, and disturbed test specimens, which are cleaned at certain time intervals for intermediate examination and subsequently exposed again. The comparability of results obtained with the two different types of test was to be investigated at the Helgoland test installation. At an exposure period of up to four years, undisturbed specimens of unalloyed and low-alloy steel grades feature considerably lower corrosion losses than disturbed specimens. At a longer exposure period of up to seven years, the corrosion rate can increase substantially again with the exposure time. This can be attributed to sulphate reduction in the anaerobic zone under the top coating. An effect of the alloying elements is also possible. With good and adequately thick coating systems, no difference ...
Pulmonary infections and tumors are a major cause of death in patients with AIDS. The combination of clinical, radiological, laboratory, and pathohistological data helps to narrow the spectrum of differential diagnoses or even allows a specific diagnosis in many patients. Nevertheless, an accurate diagnosis should be obtained as soon as possible during the clinical course of the illness to initiate treatment in time. Computed tomography (CT) has proven to provide promising results in the diagnosis of AIDS-related throacic diseases. The aim of this paper was to demonstrate the diagnostic capacities of CT in the context of particular AIDS-related thoracic pathologies. Additional information on the spectrum of pathological agents and on differential diagnostic signs is summarized. (orig.) [Deutsch] Pulmonale Infektionen und Tumore sind eine wesentliche Todesursache bei Patienten, die am erworbenen Immunmangelsyndrom AIDS leiden. In den meisten Faellen gelingt es, ...
The article explains why electric and gas utilities in Germany should not forget the domestic customers when deciding their key account management strategies and marketing policy in the competitive electricity and natural gas markets. Competition in the German energy sector has just begun, and so far the industrial customers have been absorbing most of the utilities` attention. The authors show that this is a short-sighted management strategy and present a number of reasons speaking in favour of bulding up structures or preserving the loyalty of domestic cutomers, as this customer group will finally play an important role in the utilities` efforts to keep their competitive edge. (orig./CB) [Deutsch] Wenn heute unter Marketingaspekt ueber Kundenbindung im Energiemarkt gesprochen wird, dann wird haeufig zuerst oder sogar ausschliesslich ueber die umsatzstarken Geschaeftskunden nachgedacht. Der Wettbewerb, vor allem im Bereich der Grosskunden, kuendigt sich in drastischen Einschnitten in ...
A model for combined mass and heat transfer during nonisothermal gas absorption in a two-phase gas- liquid bubbly medium with a high gas content and/or large times of gas-liquid contact is suggested. Diffusion and thermal interactions between bubbles is taken into account in the approximation of a cellular model of a bubbly medium whereby a bubbly medium is viewed as a periodic structure consisting of identical spherical cells with periodic boundary conditions at a cell boundary. Distribution of concentration of dissolved gas, temperature distribution in liquid and coefficients of mass and heat transfer during nonisothermal absorption of a soluble pure gas from a bubble by liquid are determined. In the limiting case of absorption without heat release the derived formulas recover the expressions for isothermal absorption. (orig.). With 1 fig., 1 tab. [Deutsch] Es wird ein Modell vorgestellt, das den kombinierten Waerme- und Stoffaustausch waehrend der nichtisothermen Gasabsorption in ...
Purpose: To visualise the vessel wall of the descending thoracic aorta using magnetic resonance imaging. To evaluate the diagnostic potential of tailored T{sub 1}-weighted sequences with contrast enhancement to assess systemic atherosclerotic disease. Methods: This study was performed on a clinical 1.5 Tesla scanner using a gradient strength of 30 mT/m and the phased array spine coil. A cadaver was examined to optimise a magnetic resonance imaging (MRI) protocol to evaluate atherosclerotic aortic wall disease. The acquired MR images were compared to gross specimens and histology. Subsequently seven patients who had undergone transesophageal ultrasound (TEU) with detailed assessment of the descending thoracic aorta were examined with MRI. The optimised protocol included untriggered and fat suppressed T{sub 2}-weighted turbo spin echo sequences and ECG-triggered and fat suppressed T{sub 1}-weighted spin echo sequences before and after iv administration of Gd-DTPA. Findings of the MR ...
The transport-relevant basic data recorded within the framework of a federation-wide transport data survey made in 1986 are the best-founded source at present for determining the transport volume of other radioactive materials in different economic areas of the Federal Republic of Germany. Due to the high recording rates, a sufficiently complete survey can be provided in particular with regard to the transport volume (e.g.transports/consignments/cargos, transport distance) - with the exception of transport by ship - for the ranges of application in reserach, medicine and technology. However, as regards the radiologically relevant basic data and transport modalities, the information supplied by the transporting agencies is incomplete. A table gives a comprehensive survey of type and scope of the transport volume of other radioactive materials in the Federal Republic of Germany (excluding the GDR) for transport by road, rail and air. The table also includes data on the dose rate of ...
This research project aimed to determine the factors for the transfer of the elements silver (Ag), cerium (Ce), cobalt (Co), chrome (Cr), gallium (Ga), lanthanum (La), molybdenum (Mo), niobium (Nb), radium (Ra), ruthenium (Ru), antimony (sb), thorium (Th), titanium (Ti) and uranium (U) from food into the mother's milk. This factors will be used as a basic to check and derive activity values for the contamination of food and for radiation protection at working places of suckling women. For this purpose 19 mothers collected samples daily (2-8 weeks), using the duplicate method, of all the food they consumed as well as of their milk. After microwave-assisted digestion the element contents were analysed by mass-spectroscopy with inductive coupled plasma (ICP-MS). The results of the mothers who participate for more than 5 weeks were used to make a time lapse between the intake and transfer of the elements in the mothers milk visible. (orig.) [German] Ziel dieses Forschungsvorhabens ...
The ECOTEC is a mass-efficient gasoline DOHC 4-valve per cylinder engine with balance shafts, chain driven camshafts and roller finger followers with hydraulic lash adjusters for valve actuation. It has lightweight aluminium components such as camcover, cylinder head, cylinder block, lower crankcase and structural oil pan. Other features include composite intake manifold and a coil-on-plug ignition cassette. The ECOTEC combustion system and engine architecture are optimized for low engine out and tail pipe emissions. It also includes several designed-in 'green' features for environmental benefits. The product design, development and validation process drew upon the best knowledge and practices available worldwide both inside and outside General Motor. The manufacturing systems were also designed by leveraging the best available knowledge around the world resulting in implementation of world class processes and error proofing to achieve the competitive edge in product ...
The issue of projecting policies ensuring appropriate energy supply in the future has become more important in Germany after conclusion of the agreement on a long-term nuclear power phase-out. A recent comparative analysis of a selection of scientific studies forecasting the implications of a nuclear power phase-out has shown that there is demand for more studies examining the issue in greater detail, and on the basis of an enlarged scope of research topics. Hence the present study, intended as a preliminary analysis, will investigate the potential, conditions of successful application, conceivable support schemes, and effects of those policy options that in any case, apart from the nuclear power phase-out scenario, are of essential importance in the context of building the proper conditions for sustainable development of Germany's energy sector. The options and strategies examined are: stepping up energy efficiency programmes and incentives, enhancing exploitation of the ...
A prospective study was performed on 50 patients suffering from osteochondritis dissecans of the knee and ankle to define criteria for stability and fixation of osteochondral lesions. Morphological parameters in MRI (size, fragmentation, cartilage, interface) and conventional radiology (separation, fragmentation) were registered and compared with arthroscopical staging. MRI staging based on different types of interfaces was demonstrated on T{sub 1}- and T{sub 2}-weighted images. MRI could correctly predict a Grade 1 lesion in 50%, a Grade 2 lesion in 90%, a Grade 3 lesion on 0%, and a Grade 4 lesion in 79%. Stable lesions were differentiated from unstable lesions in 90%. Radiographic findings corresponded with arthroscopic staging in only 56% of the cases because fibrotic connection may guarantee stability in case of bony separation. (orig./MG) [Deutsch] In einer prospektiven Studie an 50 Patienten mit einer Osteochondrosis dissecans (OD) des Knie- und Sprunggelenkes sollten ...
Court decisions available so far do not primarily consider the problems linked to the commissioning of an expert and his mandate, as well as the legal status of the commissioning of an expert as an administrative act which might be legally contestable. Thus there are at present no court decisions that would create legal certainty in matters of the act of commissioning a nuclear expert opinion. The current legal situation is such that an independent order for commissioning of an expert opinion in compliance with section 19 III AtG (Atomic Energy Act), which in general is given in response to the refusal of the facility operator to do so, can be independently contested on the basis of section 44 a, sentence 2 VwGO (Rules of Administrative Courts). The current practice of conflict-oriented, or nuclear power phase-out-oriented, implementation of the nuclear law poses a threat to our constitutional state and to our democracy. The supply of energy as a common good is of essential importance ...
Objective: Optimization and testing of a high temperature combustion chamber for burning coal gas and conventional fuels natural gas or fuel oil. Coal gas is not available in such quantity for testing a full scaled combustion chamber. Therefore the design of the combustion chamber is based of experimental results from model tests and numerical solution procedures. Working program: (1) Analytical model for burning coal gas implemented in an existing computational fluid dynamics (CFD) code. (2) Three-dimensional calculations of a full scaled combustion chamber with a CFD code for flows accompanied by combustion and chemical reaction. (3) Improvement of measuring method for determination of flame temperature and concentration. (4) Temperature and concentration profil measuring in a full scaled combustion chamber by operating with natural gas or fuel oil. Results: An analytical model for burning coal gas was implemented in an existing two-dimensional CFD code. The model gave acceptable ...
In comparison to deterministic criteria, probabilistic reliability indices like interruption frequency and unavailability give a more differentiated insight into reliability in an electrical energy network. One possibility for network planning based on these indices is the definition of limits for customer nodes, another is the monetarisation of reliability in terms of interruption costs. Because of numerous disadvantages, interruption cost methods could not up to now win broad recognition in network planning in Western Europe. A more recent method for the monetarisation of reliability circumventing most of these disadvantages is the insurance system. In this system the customer selects a tariff class in an insurance system, and the utility reimburses its customers in the case of an interruption. In its first section, the paper describes a method for the flexible and realistic optimisation of MV networks. This method based on Genetic optimisation is able to integrate probabilistic ...
The transversus perinei profundus muscle is a well known structure in found anatomical textbook. Fibres of this muscle are believed to form the so-called external urethral sphincter (musculus sphincter urethrae). Recently histomorphologic investigations have shown that there is no muscular connection between the musculus sphincter urethrae (external sphincter) and the muscle system of the pelvic floor. Furthermore, the external sphincter was found to be divided into parts: The transversely striated part (musculus sphincter urethrae transversostriatus) and the smooth part (musculus sphincter urethrae glaber). Similar to histomorphologic investigations, contrast-enhanced MR imaging has shown the musculus sphincter urethrae to be surrounded by fatty and connective tissue only. Neither in MRI nor in anatomical slices can any connection between the urethral sphincter and the muscle system of the pelvic floor be found. Thus, on the basis of the results presented in this work it is concluded ...
Tribological performance of alumina and silicon carbide ceramics as well as of the hardened steel 100Cr6 for reference was studied during reciprocating sliding and cavitation erosion in isooctane as substitute of gasoline and in distilled water. It was the aim to characterize effects of surface finish of the specimens and the liquid media on friction, resistance to sliding wear and cavitation erosion. Sliding wear tests were run on the self-mated ceramics and ceramic/steel pairs under conditions of boundary lubrication using a laboratory tribometer with cylinder-on-plate geometry. Vibratory cavitation erosion tests were conducted according to ASTM G 32-92. High initial surface roughness of coarse ground specimens led to a distinct running-in period during sliding contact with a transition from high to low values of friction coefficient and wear intensity. Incubation time was reduced with increasing surface roughness in the cavitation tests. Depending on the materials investigated, the ...
The paper presents fundamental studies on natural biosorption to algae of heavy metals. The investigations were carried out by TU Berlin University in a special research project (Sfb 193, 'Biologische Behandlung industrieller und gewerblicher Abwaesser'). The chlorophyceae C. vulgaris was used as reference alga, and 38 further algae were analzyed with regard to their sorption characteristics for lead, cadmium, nickel and zinc. The most effective algae were the chlorophyceae C. salina, the cyanophyceae S. hofmani and L. taylorii. The biosorption characteristics of C. salina and L. taylorii were investigated in detail. L. taylorii was found to be exploitable successfully in a technical process, so the investigations were extended to include copper. Knowledge about the chemical processes of biosorption is important for any attempt to modify the biosorption characteristics. Experiments on the incorporation of additional functional groups in the cell wall polysaccharides ...
A comparative process can be shown for the design of combined fuel cell powerstations. It is worth noting that the output of a combined powerstation working reversibly is independent of the thermodynamic state of the cell, and only depends on the reaction and thermodynamic state of the environment. The potential efficiency of gas-fired combined fuel cell powerstations is estimated at 80%. The fuel cell proves to be an isothermal heat source and not an adiabatic fluegas generator. This applies generally for all combustion power processes. Compared with external reforming, the integration of the reforming in the whole process leads to distinct advantages in efficiency if the possibilities of using the waste heat of intermediate thermal power processes are fully exploited. The plant implementation with an SOFC gas turbine process shows that realisation of a relatively simple plant concept leads to efficiencies distinctly above 70%. The enclosure design is of central improtance for the ...
The measuring series was performed from November 1991 through April 1992 in seven drinking-water conditioning plants of the Fichtel mountains area in the north-eastern part of Bavaria, and the results revealed as an annual average a dose of about 1 - 40 WLM. The area of interest is a drinking-water catchment area where the ground water and other water resources include waters particularly rich in radon content, which explains this relatively high dose range. This is why comprehensive, specific local and long-term mearurements were carried out in order to assess the occupational radiation dose in the drinking-water conditioning plants, taking as a model site the conditioning plant of the municipal utilities of Hof in Weissenstadt. These more specific measurements were performed by the Technical Inspectorates (TUeV) of Bavaria and Saxony and the isotope laboratory of Georg-August University of Goettingen in mid-April 1994 (Goettingen University, TUeV Saxonia and Bavaria) and from June ...
This proceedings volume comprises 17 papers on the following subjects: Methane hydrates, compounds of gas and water; Compressed air stroage gas turbine power plants / Scheduled application for load levelling between varying wind power production and power demand; Modern pumped storage power stations in the GW range - the PSW Goldisthal example; Lead batteries - new developments and future applications; Alkaline battery systems for hybrid electric road vehicles; Lighium systems and their applications; Zinc/air cells; Hydrogen storage - metal hydride storage, compressed gas storage, LNG storage; Carbon nanofibres for hydrogen storage; Double-layer condensers - technology, cost, perslpectives; Supercondensers in motor vehicles; Superconducting magnetic energy stores; Flywheel storage - status report; Decentralized energy storage in the European integrated supply grid - the EU project DISPOWER; Intercontinental integration of power supply - perspectives of full-scale power supply on the ...
The high-speed direct-injection diesel engine for passenger cars has been a resounding success in the marketplace in the last few years. This was due to an intensive development process as a result of which the direct-injection diesel engine for passenger cars is currently setting new standards with regard to performance and fuel consumption in spite of the constant tightening of emission regulations. Of particular importance in this context is exhaust gas recirculation (EGR). This technology permits a considerable reduction in nitrogen oxide emissions, which are especially critical in the case of the direct-injection diesel engine. In addition, continuing development of supercharging technology, in particular the turbocharger with variable turbine geometry, have allowed further improvement of the full-load behaviour and the engine response and a considerable reduction in the fuel consumption of direct-injection diesel engines. This FVV paper deals with the fundamentals of the ...
The paper discusses multiaxial, isothermal and thermocyclic experiments with tubes made of the austenitic steel 1.4909 (AISI 316 L(N)). The thermocyclic stress is induced by periodic, inductive heating of the tube outer wall and simultaneous, continuous water cooling of the inner wall. Temperature gradients above 100 K/mm are measured, which cause fatigue cracking, predominantly in the inner wall. The experiments with the isothermally stressed tube specimens are intended to simulate the equi-biaxial stress conditions that are typical of the thermocyclic stress regime. This stress regime is created by superimposed longitudinal stress (tension/compression), and circumferential stress (internal/external compression). A novel test bench was realised specifically for the experiments. The paper explains design, operation, and measuring techniques, especially of the circumferential strain measurements. The measured results are compared with results of uniaxial strain cycling experiments made ...
Preserving customers` investments in capital goods is one of the strategic market services offered by ABB, and to this end the company has developed project-specific retrofit concepts especially for older power generation plant. A prime example of such a modernization is the Umm Al Nar East (UANE) combined cycle power station in Abu Dhabi, UAE. UANE has two gas turbines of type GT13D, which together generate 140 MW of electrical energy, and heat-recovery boilers which supply steam to a seawater desalination plant with a capacity of 80 million liters of drinking water per day. After almost 20 years in operation, UANE is being modernized. To address the owner`s concerns and minimize plant downtime, ABB has introduced Service, Operation and Rehabilitation (SOR) Key Account Management for Abu Dhabi. In the first phase of the modernization project, the static starting equipment was upgraded and the mechanical turbine governor replaced by the EGATROL electro-hydraulic control system. Also, ...
For a wider application of GaAs single crystals for semiconductor devices a cheaper process to grow crystals with high purity and low dislocation density is required. According to todays knowledge the Czochralski method with a hot wall vessel should be the choice. The temperature of the vessel has to be 700deg C to avoid condensation of arsenic which vapourizes from the 1240deg C hot melt. Arsenic vapour is very agressive against all metals. Therefore the corrosion resistance of metals and alloys with a high melting point and also ceramics has been tested. All the alloys under investigation are corroded severely so that they have to be excluded as a material for the vessel. The metals tantalum, molybdenum and tungsten are more resistent, titanium forms initially a thick protection layer and further corrosion is greatly reduced. The ceramics investigated (TiB{sub 2}; ALN; Makor; BN) are not attacked by arsenic though they may store some arsenic. (orig./MM). [Deutsch] Fuer breitere ...
The role of high-resolution computed tomography (HRCT) and magnetic resonance imaging (MRI) in the diagnosis of preoperative and postoperative complications caused by acquired cholesteatomas will be described in this paper. The pre- and postoperative imaging of the temporal bone was performed with HRCT and MRI. HRCT and MRI were performed in the axial and coronal plane. MRI was done with T2 weighted and T1 weighted sequences both before and after the intravenous application of contrast material. All imaging findings were confirmed clinically or surgically. The preoperative cholesteatoma-caused complications depicted by HRCT included bony erosions of the ossicles, scutum, facial canal in the middle ear, tympanic walls including the tegmen tympani, and of the labyrinth. The preoperative cholesteatoma-caused complications depicted by MRI included signs indicative for labyrinthitis, and brain abscess. Postoperative HRCT depicted bony erosions caused by recurrent cholesteatoma, bony defects ...
The experimental effect investigation programme on Zircaloy-4/air oxidation was pursued and expanded to isothermal specimen exposure and the comparison of the oxidation between the atmospheres Ar/O{sub 2} and air. In close connection with the EC project OPSA, which is meanwhile terminated, the investigation concerned specimen exposure in a thermobalance to flowing atmospheres, namely dry Ar/O{sub 2} of composition 80/20 or synthetic air, respectively. As test parameters the linear heat-up rate was varied in the range 5 to 40 K/min and the ramp or holding temperature between 800 and 1500 C. Mass increase and reaction rate were continuously recorded or evaluated in temperature/time dependence. The oxide scale growth was found to be accompanied by colour changes, crack formation and spalling of layers, as well as by dimensional substrate growth, which are the reasons for the observed kinetic results. The microstructural investigation confirms nitrogen to be essentially responsible for the ...
Poly-Lactic-Acid (PLA) was evaluated for coating of vascular endoprotheses in the treatment of experimental arterio-venous-fistulae (AVF). Bilateral carotid-external jugular AVF were created in 5 adult dogs. 7 PLA coated nitinol stents were placed via a transfemoral approach covering 5 AVF. The contralateral AVF remained untreated. Angiography was performed immediately after stent placement, at weeks 1 and 3 and at months 3, 6 and 9. All grafts were removed and underwent histologic examination. In 2 cases the occlusion of the AVF was successful, while misplacement occurred in 3 cases. Occlusion of the parent vessel was disclosed in 3 cases. Histologic examination revealed a mild inflammatory reaction with the presence of macrophages. There was no foreign-body reaction or fragmentation of the arterial vessel wall. PLA, which is a well-known biodegradable material, showed a good mid-term biocompatibility. Elastic mismatch of the non-elastic coating and the self-expandable nitinol stent ...
Nuclear energy will have to cope more and more with a rapid changing environment due to economic competitive pressure and the deregulatory progress. In current economic environment, utilities will have to focus strongly on the reduction of their total generation costs, covering the fuel cycle costs, which are only partly under their control. Developments in the fuel cycle will be in the short-term rather evolutionary addressing the current needs of utilities. However, within the context of sustainable development and more and more inclusion of externalities in energy generation costs, more performing developments in the fuel cycle could become important and feasible. A life-cycle design approach of the fuel cycle will be requested in order to cover all factors in order to decrease significantly the nuclear energy generation cost to complete with other alternative fuels in the long-term. This paper will report on some of the trends one could distinguish in the fuel cycle with emphasis ...
In the future even more than in the past, nuclear power will be indispensable in the present industrialized countries and in those still under development. The safe, nonpolluting, and economic supply of energy to mankind in the future includes so many different problems that the technology of the high-temperature reactor at its present level of development, and with the possibilities is offers above and beyond those provided by other, established, technologies, does not have to mark the end of some old line of development, but rather should be seen as the starting point of a development offering promise for the future. It is for this very reason that the extensive, valuable knowledge and experience accumulated in the construction, operation, and decommissioning of the AVR and THTR plants, the development of the HTR module and other variants and, last, but not least, the valuable results of projects such as PNP, NFE, and HHT, must be preserved at the research centers and with former ...
Purpose: The aim of this study was to test the feasibility of iliac artery stent placement under MR guidance with real-time MR radial scanning in an animal model. Materials and methods: The experiments were performed on three pigs in a 1.5 T scanner. Radial scanning with a gradient echo technique (T{sub R} 8.4 ms, T{sub E} 3.6 ms, flip angle 10 ) was used. A dedicated backprojector performed the reconstruction of the raw data in real-time. The resulting MR-images were displayed on LCD screens beside the magnet. The sliding window reconstruction technique allowed image acquistion at a frame rate of 16 images per second. MR-compatible self-expanding stents with a diameter of 8 mm and a length of 3 cm were placed into the left iliac artery. Their positions were verified by digital subtraction angiography (DSA) and compared to MRI. Results: All stents were successfully placed. Stent positions as monitored by real-time MR were identical to those seen on DSA images. The time needed for exact ...
Backgrund: Interleukin-1, tumornecrosisfactor-{alpha} and interferon-{gamma} endogenously provide protection of the hematopoietic system against radiation. Thiols have already been used successfully as radioprotective agents. In this study the effect von N-acetylcysteine (NAC) on the release of interleukin-1{alpha} and {beta} (IL-1), interleukin-2 (IL-2), interferon-{gamma} (IFN-{gamma}) and tumornecrosisfactor-{alpha} (TNF-{alpha}) was assessed in an in vitro assay. Patients and Methods: Whole blood samples from 8 healthy volunteers were stimulated with 7.5 {mu}m/ml PHA. NAC was added at concentrations of 0.6, 6, 12 and 24 mmol/l. Subsequently the samples were irradiated with a dose of 18 Gy according to preceding validation experiments. Results: IL-1{alpha}, IL-1{beta} and IL-2: In comparison to simulation and radiation alone the addition of 0.6 and 6 mmol/l with IL-2 also 12 mmol/l, NAC resulted in a significant increase of the cytokine-concentrations. The highest concentration of ...
Initially, the decision of the operator in Dortmund-Derne to select the impact-type separator concept is explained. None of the tenderers for this 52 t/h boiler could supply references for this fluidized bed steam generator concept with staged combustion in a high-expansion fluidized bed. Under the circumstances, the simple configuration of the Steinmueller fluidized bed steam generator, its compact construction, the reduced amount of refractory and the operational behaviour of the boiler resulting therefrom were decisive in the operator`s decision to select this concept. The development schedule shows the individual stages from cold and hot trials in various test rigs and pilot plants to the final design. So far, this fluidized bed steam generator concept has been realized in the plants Derne (52 t/h), commissioned in November 1989, and Brilon (100 t/h), commissioned in November 1990. The discussion on the essential design features points out to the deliberate differences in the two ...
The amounts of lead and cadmium produced and processed in these days are considerable. As a result, our environment is increasingly polluted by heavy metals and industrial installations, motor vehicles or incinerating plants appear to be among the main culprits here. Air and water are the media permitting the entry of heavy metals into our natural environment where they accumulate in the soil and then gradually migrate into the plants. Their further transport in the food constitutes the third step in the environmental spread of heavy metals. The consumption of muscle and organ meats, of vegetables, fruits, canned food and drinking water is unavoidably associated with some ingestion of lead and cadmium. The degree to which they are taken up and stored in different tissues is determined by absorption properties and the nutritional state of the organism. Cadmium tends to accumulate in the kidneys, lead is mainly stored in the bones. A continuously increasing uptake finally results in ...
...and it's really a pleasure to ...you and ...and for ...was shelled and then doses of pleasure for me to ...and my director general ...? and journal article ? ...but and yeah well that's um ? ...and ...and what could be achieved ? what might be the consequences ...? and ...and ...and ...and ...and ...structural because and ...over and hopefully is also serve the purpose to get ...principles and ...and ...and ...how to use them and future ...and and that ...and purposes and that's very important ...you and ...and ...and in the future ? and yeah ...true and ...and ...just and and and and and the order of nuclear physics a ...useful and ...too much ? and ...portable comes from and ...and ...and ...and ...no more ? how to knowledge and the and ...and ...and and keep ever seen all of all ? ...and ...and ...and what you're ...and ...and ...and you and ...and ...and ...and so when you keep that and and ...and ...? and ...and ...and ...the problems and the other side ? ...door and a ...and ...