The article deals with the following topics: reliability calculation as a basis of a maintenance strategy leads to the knowledge which equipment seems to be critical in the context of a supply interruption; procedure of a risk management; information for a risk assessment: probability of an equipment malfunction, reliability calculation on the system level, failure cost, maintenance cost, further conditions. The article shows an example for a calculation. [German] Die Zuverlaessigkeitsberechnung als Grundlage einer Instandhaltungsstrategie fuehrt zu der Kenntnis, welche Betriebsmittel kritisch im Hinblick auf eine Versorgungsunterbrechung sind. Eine anschliessende Risikobetrachtung schliesst deshalb neben der Betrachtung der nichtgelieferten Energie auch die uebrigen Kosten einer Stoerung ein, die mit den finanziellen Aufwendungen fuer eine Instandhaltung zu vergleichen sind. Im Folgenden wird ein Vorschlag fuer eine Risikobewertung von ...
Two isothermal sections were prepared at 1000 and 1150 C showing the low-Zr phases of the system Fe-Al-Zr. The phase equilibria were determined by means of X-ray powder diffractometry and electron beam microanalysis. For initial characterisation of mechanical properties, hardness values are determined and added to the tabulated data. (orig./MM) [German] Es werden am Fe-Al-Zr-System zwei isotherme Schnitte durch den zirkoniumarmen Teil des Systems bei 1000 und 1150 C erstellt. Die auftretenden Phasengleichgewichte werden mit Hilfe der Roentgenpulverdiffraktometrie und Elektronenstrahlmikroanalyse aufgeklaert. Zusaetzlich werden zur ersten Charakterisierung der mechanischen Eigenschaften Haertewerte bestimmt.
Line conditioners control voltage isolated in external conductors. Changes of Stern-Delta connections involve voltage drop in a nonloaded external conductor and are therefore compensated. The payback period of a line conditioner lasts normally between one to three years, according to the investment cost for the alternative medium-sized voltage to be constructed. (GL)
Old banknotes may be tomorrow's biomass. Experts on biowaste are investigating two new processes for disposal of the 1000 tonnes of old bills sorted out every year which may be an alternative to combustion. The author presents details.
The intermetallic phase NiAl is a potential material for high-temperature applications; however, its technical application was prevented so far by its high brittleness at room temperature. This problem may be solved by incorporating relatively high-ductility particles into the NiAl matrix. Controlled crack propagation experiments, tensile and pressure tests were carried out in order to analyze the toughness and deformation characteristics of NiAl composite materials containing niobium or molybdenum particles at room temperature and in ambient atmosphere. Both the niobium and the molybdenum particles increase the toughness as compared to the pure NiAl matrix, but no ductilisation was observed in the composite materials investigated. Model experiments in consideration of experimental data suggest, hovewer, that the toughness and ductility of NiAl may be enhanced by optimizing the ...
Biosorption behaviour of and toxic effects of heavy metals in submersed and immobilised microorganisms was studied in batches and in continuous processes in an airlift-recycle reactor. Nickel, cadmium, and zinc were used as heavy metals. (orig./VHE) [Deutsch] Am Beispiel einer Naphthalin-2-sulfonsaeure-abbauenden Kultur wurde das Biosorptionsverhalten und die toxische Wirkung von Schwermetallen auf submerse und immobilisierte Mikroorganismen im Batch-Ansatz und im kontinuierlichen Betrieb in einem Airlift-Schlaufenreaktor untersucht. Als Schwermetalle wurden Nickel, Cadmium und Zink eingesetzt. (orig./VHE)
In Duisburg the Citibank is building a new call center. As an alternative to the conventional switch cupboard technology, an innovative energy bus technology by ABB Gebaeudeautomation is being used: it involves less planning effort, faster start of operation and a shorter construction time, cost saving through lower space and material demand, plus the advantage of flexibility of extension. (orig.) [German] In Duisburg entsteht zur Zeit der Neubau eines Call Centers der Citibank. Dabei wird als Alternative zur herkoemmlichen Schaltschranktechnik die innovative Energiebus-Technik von ABB Gebaeudeautomation eingesetzt: Geringerer Planungsaufwand, schnellere Inbetriebnahme und kurze Bauzeit, Kostenersparnis durch geringeren Platz- und Materialverbrauch sowie flexible Erweiterbarkeit sind die Vorteile. (orig.)
Zusammenfassung Das Konzept der ?quivalenten Spannung (Vergleichsspannung) wird seit langem angewendet und hat sich bew?hrt. Ein wesentlicher Grund daf?r liegt darin, dass es u.?a. bei der Formulierung ph?nomenologischer Werkstoffmodelle weiterhilft. Von Nachteil ist, dass es weder mit physikalischen Prinzipien in Verbindung steht, noch Informationen ?ber die Mikrostruktur des Werkstoffs enth?lt. Trotzdem wurden zahlreiche Hypothesen zur Formulierung von ?quivalenten Spannungen in der Vergangenheit aufgestellt und in der Praxis mit unterschiedlichem Erfolg angewendet. Als Basis f?r die Systematisierung der zahlreichen Modelle hat Yu die Unified Strength Theory (UST) vorgeschlagen. Diese eignet sich, u.?a. inkompressibles inelastisches Materialverhalten sowie kompressible Werkstoffe mit unt...
Automatic ultrasonic testing is presented as a method for recurrent inspections of pressure gas vessels, from validation to practical testing to customised test applications. National and international regulations and standards are presented along with related implementation problems. [German] Es wird die automatisierte Ultraschallpruefung im Bereich der wiederkehrenden Pruefung von Druckgasbehaeltern, als Alternative zur herkoemmlichen, klassischen Wasserdruckpruefung, vorgestellt. Von der Validierung ueber die praktische Erprobung bis hin zur kundenspezifisch entwickelten Pruefapplikation. Es werden die Anforderungen aus nationalen und internationalen Vorschriften und Normen sowie die damit zusammenhaengenden Umsetzungsprobleme behandelt.
The goal of this project was to develop a new technology for preparing samples for transmission electron microscopy (TEM) on the basis of ion fine beam processing. For this purpose processes of ion-beam-assisted removal (sputtering), separation, sample handling and ion-beam-assisted chemical etching as well of system-inherent components were examined. As an alternative to a Ga-source a liquid-metal ion source based on a AuGeSi alloy was developed, characterised and used in the FIB 4400. [German] Aufgabe des Projektes war die Entwicklung einer neuen Technologie zur Probenpraeparation fuer die Transmissions-Elektronenmikroskopie (TEM) auf der Basis der Ionenfeinstrahlbearbeitung. Dazu wurden Prozesse der ionenstrahlgestuetzten Abtragung (Sputtern), der Abscheidung, des Probenhandling, des ionenstrahlgestuetzten chemischen Aetzens sowie systemeigener Komponenten untersucht. Als Alternative zur Ga-Quelle wurde eine ...
The author investigates whether waste fermentation is an economically feasible alternative to composting. Decisions on projects and sites should not be made until the basic problems of feasibility and economic efficiency are solved. [German] In Anbetracht der derzeitigen Situation bei der Restmuellbehandlung, in der die mechanisch-biologische Behandlung als Alternative zu einer rein thermischen Behandlung immer mehr an Bedeutung gewinnt, stellt sich immer haeufiger die Frage, ob die Restmuellvergaerung eine Alternative zur ausschliesslichen Restmuellrotte darstellt. Diese Frage muss zunaechst prinzipiell aus Sicht der technischen Machbarkeit und von der Sinnhaftigkeit, hier vor allem von der Kostenseite her, betrachtet werden. Erst daran anschliessend lassen sich projekt- und standortbezogene Betrachtungen anstellen. Hinsichtlich der technischen Machbarkeit laesst sich im wesentlichen auf den grosstechnischen Erfahrungen der letzten 8 Jahre bei ...
In the presented case study CRS processing was able to improve the overall data quality of the processed lines in terms of signal-to-noise ratio and imaging. The complex geology is causing serious problems in conventional NMO/DMO processing that were solved by CRS processing. Even a depth processing with velocities calculated from CRS attributes gives good results similar to those from PreSDM in terms of the velocity field. Data quality of poststack depth migrated CRS stacks is even better than the image from PreSDM. (orig.)
The first biogas plant using the Plauen method has been operated without failures in the Saxon Vogtland since May 1987. This large scale anaerob treatment plant which is the first one in Germany handles besides agricultural recidual substance both municipal and industrial organic residues. The results show clearly that fermentation is a real alternative to composting, combusting and deponing. (orig.)
A high-temperature flow reactor and different technical plants were tested within the framework of this research project. Anthropogenic N{sub 2}O emissions form during secondary flue gas or waste gas purification as secondary emissions during denitrification and pollution abatement measures. N{sub 2}O forms as an intermediate product as NO is reduced to N{sub 2}. Under certain operating conditions N{sub 2}O is not decomposed completely. Different secondary flue gas purification measures, i.e. selective noncatalytic reduction (SNCR), selective catalytic reduction (SCR), and nonselective catalytic reduction (NSCR) were investigated testing several technical plants and the high-temperature flow reactor. (orig./EF) [Deutsch] Das Forschungsprojekt ``Messung der N{sub 2}O-Emissionen von Verbrennungsanlagen und Untersuchung von Moeglichkeiten zur Emissionsminderung`` wurde an einem Hochtemperatur-Stroemungsreaktor und an verschiedenen technischen Anlagen durchgefuehrt. ...
Facility management has long been regarded as a cost reduction measure, but it is also a means of raising the financial worth of a building so that landlords can get higher rents or sell the building at a better price. [German] Lange Zeit wurde Facility Management als eine Massnahme zur Kostensenkung angesehen. Heutzutage zeigt sich immer mehr, dass das Facility Management sehr viel umfassender zu verstehen ist: Der Wert eines Gebaeudes bemisst sich nicht allein an einer niedrigen Kostenquote, sondern er soll umfassend Investoren wie Mietern den hoechst moeglichen Nutzen bringen. Nicht allein der kostenguenstige Betrieb ist entscheidend, sondern der Wert des Gebaeudes muss insgesamt gesteigert werden. (orig.)
{gamma} Ti-Al have a higher temperature potential than commercial titanium alloys and a 50 percent lower density than nickel base superalloys. Application temperatures in aircraft turbines are 750 C and above. The authors investigated the high-temperature performance of {gamma} TiAl, i.e. isothermal high-temperature fatigue and the type and importance of damage. LCF experiments were made in the temperature range of brittle/ductile transition in air and vacuum. Damage mechanisms were characterized by microstructural investigations. [German] Unter den modernen Hochtemperaturwerkstoffen kommt den Legierungen auf Basis von {gamma}-TiAl eine zunehmend wichtige Bedeutung zu, da diese Werkstoffe ein hoeheres Temperaturpotential als alle kommerziellen Titanlegierungen haben und eine im Vergleich zu den Nickelbasis-Superlegierungen um ca. 50% geringere Dichte aufweisen. TiAl-Werkstoffe, die ...
The study required by the West German Ministry of Research and Technology (RS 605) for the Committee on 'Future Nuclear Energy Policy' of the 9th German Parliament is concerned with the following main points: 1) Assessment of technical risks from the social aspect; 2) Discussion of terms and quantification of risks; 3) 'Engineering judgment' and 'questionable' methods in the Fast Breeder analysis of the Society for Reactor Safety (GRS); 4) Assessment criteria of potential damage.
The VerTech Pit Method for wet oxidation of municipal sewage sludge offers an ecologically and economically advantageous alternative for dealing with sewage and special sludges. Europe`s first commercial plant has now been commissioned in Apeldoorn in the Netherlands following industrial-scale trials in the USA. Up to its present stage of operation the plant has achieved a high degree of reduction of solid residues and a favourable resource and environmental profile, thus impressively confirming earlier results. It is amply in keeping with the landfill criteria laid down in the Household Waste Technical Code. Furthermore, the potential sludge throughput has been found to exceed the projected value. [Deutsch] Mit dem VerTech-Tiefschachtverfahren zur Nassoxidation kommunaler Klaerschlaemme steht ein alternatives Verfahren zur Behandlung von Klaer- und Sonderschlaemmen zur Verfuegung, das oekologische und wirtschaftliche ...
The RCP method was designed as a residue-optimised alternative to the thermally optimised grate firing of residual wastes. Its technical realisation and development to market maturity took no more than 5 years. In the first process stage the waste is converted to high-carbon pyrolysis charcoal and high-rank gas in the absence of oxygen. In the second stage these substances are oxidised by addition of oxygen. The resulting temperature causes the non-combustible constituents of the slag to melt. In a third, optional, stage this molten slag can be liberated of (heavy) metals to such an extent that it can subsequently be used directly as additive for grinding. Further exhaust gas treatment is facilitated by the use of a circulatory fluidised-bed secondary combustion chamber. Despite the reduced flue gas volume and resultant higher pollutant concentrations in the crude gas, overall emissions are lower than in conventional plants. [Deutsch] Das reststoffoptimierte RCP Verfahren ist ...
A new emissivity measurement device with inductive sample heating is described. The disc shaped samples can be measured between 800 C and 2000 C in vacuum or in each available gas atmosphere. Two kinds of surface temperature measurement methods are described, one by measuring in a blackbody hole and one by measuring at the surface without additional measures to correct emissivity. Total normal and spectral emissivity at wavelengths between 0,5 {mu}m and 8,3 {mu}m of various high temperature materials like platinum and Pt-Rh-alloys, siliconcarbide and molybdenum disilicide have been measured. From the investigated materials a few have been selected as reference samples for comparative emissivity measurements fullfilling the requirement of stability on air up to 400 C to 1000 C in order to ensure reproducibility of the results at different measurement conditions in air and in vacuum. (orig.) [Deutsch] Der Aufbau einer neuen Messapparatur fuer Emissionsgradmessungen bei Temperaturen ...
A part of the waste materials arising in iron and steel manufacture is utilised physically, either internally for the recovery of iron or externally for the production of cement and nonferrous metals. Most of these materials can be used without prior processing. Iron and steel-relevant waste materials which at present are still landfilled or disposed of as hazardous wastes are not immediately suitable for physical recycling as secondary raw material. These waste materials have to be processed without exception before they can be used again in the existing steel and iron manufacturing plants. The results of the authors` own studies have clearly shown that the cupola furnace is suited for the use of a wide variety of waste materials. [Deutsch] Ein Teil der bei der Eisen- und Stahlerzeugung anfallenden Abfallstoffe werden entweder intern zur Rueckgewinnung des Eisens oder extern in der Zement- bzw. Nichteisenmetallgewinnung stofflich verwertet. Dabei handelt es sich ...
Today electric power steering systems are regularly considered by the car manufacturers as an alternative to a conventional hydraulic power steering system in the development of new vehicle platforms. Simplified vehicle assembly and the potential to contribute to the reduction of the vehicle's energy consumption are the main motivation for this. The performance of the systems available at present with 13.5 V supply voltage will be improved even more as soon as the future 42 V vehicle electrical systems are available. Like most active chassis systems, electric power steering has to meet the highest safety requirements imaginable. This article summarizes the safety philosophy of the TRW rack drive Electric Power Steering system. (orig.) [German] Elektromechanische Servolenkungen werden heute bei der Entwicklung neuer Fahrzeuge als Alternative zur konventionellen hydraulischen Servolenkung in Betracht gezogen. Die vereinfachte ...
Basic research in relation to a complete utilisation of animal substances as an alternative to a thermal disposal was done. The composition of different kinds of bones were investigated as well as their amounts which are available. Conventional utilisation was opposed to the innovative utilisation. Technologies will be selected which should be developed, because they have the chance in the case of a fast industrial realisation to get a good profit. There is a global requirement for the technologies which are developed and their products which can be produced with this. The raw material basis is available in the necessary scale in nearly all countries. (orig.) [German] Grundlegende Untersuchungen zur ganzheitlichen Verwertung von tierischen Substanzen als Alternative zur thermischen Entsorgung wurden durchgefuehrt. Es wurde die Zusammensetzung der verschiedenen Knochenarten und ihr Aufkommen untersucht. Die konventionelle ...
The results of the experiments on the pressure oxidation of oil and fat in waste waters shows that the final COD and TOC values decrease with growing temperature and reaction time and decreasing initial concentration. Oxidation of oil and fat in waste water is no straight forward procedure. Therefore it should be compared in the individual case with laternative methods in terms of cost and economic efficiency. (EF) [Deutsch] Die Ergebnisse der Versuche zur Druckoxidation von Oel und Fett in Abwaessern zeigten, dass sich die CSB- und TOC- Endkonzentration verringerte mit steigender Temperatur, Reaktionszeit und verringerter Ausgangskonzentration. Die Oxidierbarkeit von Oel und Fett in Abwaessern ist sehr schwierig. Deshalb sollte in jedem Einzelfall ein Vergleich mit alternativen Verfahren bezueglich Aufwand und Wirtschaftlichkeit vorgenommen werden. (EF)
We develop a general framework for the formulation of the action principle and the noether theorem for classical noncommutative field theories. We give a concrete example of an algebra that fits into this framework. It describes a scalar field theory on noncommutative minkowski space. We develop a notion of locality for this algebra and investigate the locality properties of localised interaction terms. This leads us to the definition of local functionals on the field algebra. We propose a scheme for the quantisation of these functionals. (orig.) [German] Wir entwickeln eine allgemeinen rahmen, der es erlaubt, das wirkungsprinzip und das noether-theorem fuer klassische nichtkommutative feldtheorien zu formulieren. Als ein konkretes beispiel betrachten wir eine algebra, die sich in diesem rahmen einfuegt, und die eine skalare feldtheorie auf dem nichtkommutativen minkowski-raum beschreibt. Fuer diese algebra wird ein lokalitaetsbegriff entwickelt und untersucht, ...
FLUTAN is a highly vectorized computer code for 3D fluiddynamic and thermal-hydraulic analyses in Cartesian or cylinder coordinates. It is related to the family of COMMIX codes originally developed at Argonne National Laboratory, USA, and particularly to COMMIX-1A and COMMIX-1B, which were made available to FZK in the frame of cooperation contracts within the fast reactor safety field. FLUTAN 2.0 is an improved version of the FLUTAN code released in 1992. It offers some additional innovations, e.g. the QUICK-LECUSSO-FRAM techniques for reducing numerical diffusion in the k-{epsilon} turbulence model equations; a higher sophisticated wall model for specifying a mass flow outside the surface walls together with its flow path and its associated inlet and outlet flow temperatures; and a revised and upgraded pressure boundary condition to fully include the outlet cells in the solution process of the conservation equations. Last but not least, a so-called visualization option based on VISART ...
CT-Expo is a novel MS Excel application for assessing the radiation doses delivered to patients undergoing CT examinations, based on computational methods that were used to analyze the data collected in the German survey on CT practice in 1999. The program enables the calculation of all dose quantities of practical value, such as axial dose free-in-air, weighted CTDI, dose-length product, effective dose and uterine dose. In contrast to existing programs for CT dose assessment, CT-Expo offers a number of unique features, such as gender-specific dose calculation for all age groups (adults, children, newborns), applicability to all existing scanner models including correction of scanner-specific influences, and the possibility of comparison with the results from the German CT survey on CT practice. Three different application modules offer free and standardized dose calculations as well as a comprehensive benchmarking section including guidance on dose optimization. The program is ...
Pyrolysis and combustion of CH are investigated. In order to reduce the work required for the present combination of parameters, the following substances were selected: Hexachloroethane, hexachlorocyclohexane, hexachlorobenzene and hexachlorophene. The model substances were pyrolyzed or combusted in varying conditions, and the combustion or pyrolysis products were analyzed. Only the main products were of interest; trace components are important only as far as they may throw light on the reaction mechanisms. The furnace design resulted in incomplete combustion and pyrolysis reactions, so that products of all stages of combusition or pyrolysis were available for analysis. Reaction processes can be derived from the products. As an alternative to thermal treatment of refuse, biological degradation of chlorinated hydrocarbons was gone into. The efficiency of decomposition by microorganisms was to be compared with the efficiency of thermal destruction of chlorohydrocarbons. The ...
To evaluate the current situation and implementation of embolization of uterine leiomyomas into the treatment concept in women with symptomatic uterine leiomyomas in Germany. A questionnaire addressing the clinical background of uterine myomas, recommended treatment concepts, preclinical evaluation, technical approach and complications was sent to 164 departments of gynecology and radiology in Germany. 33 radiological departments and 19 gynecological departments submitted a completed questionnaire. Only 7 departments of radiology reported to have own experience with embolization of uterine leiomyomas, while only 2 departments of gynecology considered embolization as an alternative treatment option in patients with symptomatic leiomyomas. 18/33 radiological departments offer this treatment option but get no patient referrals. Agreement was found concerning the indications for treatment, preclinical evaluation by ultrasound and MRI, preferable location of treatable fibroids, technical ...
With publication the fire design rules of the Eurocode and the national application documents (NAD) for the first time also calculation methods of constructive structural fire protection are available. This dimensioning of components and structures in fire case is based on the normal temperature design on Eurocodes and can be applied in the future as alternative to the classical fire design method of the German standard DIN 4102 part 4. In this contribution a view of the proof procedures of the Eurocode fire protection parts and the arrangements of the NADs is given as soon as the application of these fire design rules in Germany is described. (orig.) [German] Mit der Veroeffentlichung der Eurocode-Brandschutzteile als Vornormen und der zugehoerigen nationalen Anwendungsregelungen (NAD) als DIN-Fachberichte stehen erstmals auch rechnerische Nachweisverfahren fuer den konstruktiven baulichen Brandschutz zur Verfuegung. Diese ...
1. Cyanide degradation: Of the cyanide- and thiocyanate-degrading bacteria, Burkholderia cepacia and Pseudomonas spec. were the most effective. 2. Biosorption: Of the isolates suited for biosorption of heavy metals, 597-A (non-identifiable) and 597-A2 (Aspergillus fumigatis) had the biggest potential. The sorption capacity of the fungi for metals varied with the C source used for their growth: apple juice > molasses > glucose. The fungi are not cyanide-sensitive and can even degrade cyanide. Living biomass had better metal sorption efficiencies than dead mycelium. The biosorption rates in waste water were usually higher than in broth. Depending on the metal composition and concentrations and on the exposure time and volume of the mycelia, up to 85 % of the initial concentration was removed from the liquid phase. The capacity of different biomasses for the sorption of metal mixtures was between 65 and 80 mg/g of dry matter depending on the experimental conditions, with ...
The isothermal flow field for the axial cyclone has been experimentally determined. The velocity fields are used for determination particle paths (particle removal and suspended state), and inter alia of heat and mass transfer processes in the axial cyclone combustion chamber. The results are extremely significant as input value approximations for mathematical modelling, since experimentally obtained results are indispensable for complex flows and geometries. (orig.) [Deutsch] Es ist fuer den Axialzyklon experimentell das isotherme Stroemungsfeld ermittelt. Die Geschwindigkeitsfelder dienen zur Ermittlung der Partikelbahnen (Partikelabscheidung, Schwebebedingung), der Waerme- und Stoffuebertragungsprozesse u.a. in der Axialzyklonbrennkammer. Die Ergebnisse sind als Startwertnaeherung bei einer mathematischen Modellierung sehr wichtig, da bei komplexen Stroemungen und Geometrien versuchstechnische Ergebnisse unumgaenglich sind. (orig.)
For the preparation of photonic probes for hadron physics the determination of energy and polarization of the photons is essential. In this dissertation in a first part a possibility of the determination of the degree of polarization by use of the asymmetry observables is presented. In a second part a possibility isd discussed to perform an energy and polarization tagging of nearly real photons in electron scattering under small Q{sup 2}. By this method it should be possible to tag billions of photons per second.
So far, publications in turbomachinery engineering have tended to neglect the description of control systems and strategies which could be converted into practical guidelines for turbine operation. The contribution describes the power station turbine as a basis for modelling the control stage. The solutions will serve as a basis for further type-specific investigations of the problem. [German] Eine vornehmlich regelungstechnisch ausgerichtete Beschreibung des thermodynamisch-mechanischen Wirkungsgeschehens im Bereich der Regelstufe von Dampfturbinen sowie deren Umsetzung in schluessige, betriebsrelevante Aussagen fehlen bislang in der Turbomaschinenliteratur. Im Beitrag werden am Beispiel der Kraftwerksturbine die Grundlagen fuer eine modelltechnische Nachbildung der Regelstufe entwickelt. Die Loesungen dienen als Ausgangsbasis fuer weitere typenspezifische Bearbeitungen dieses Problems. (orig.)
Better quality of thermal comfort as well as reduced heat energy demand and accordingly CO{sub 2} emission can be achieved by better heating and ventilation strategies in private buildings. The paper deals with a novel model-based measurement and automation system. It describes the implementation of better strategies under given technical circumstances. (orig.) [German] Durch Verbesserung der Heizungs- und Lueftungsstrategien im privaten Lebensbereich kann sowohl Heizenergie eingespart und damit die CO{sub 2}-Emission verringert, als auch die Raumbehaglichkeit verbessert werden. Der Beitrag behandelt ein modellgestuetztes Mess- und Automatisierungssystem, mit dem die Realisierung der verbesserten Strategien unter gegebenen technischen Randbedingungen praktisch erst moeglich wird. (orig.)
Zusammenfassung Hintergrund Seit 2005 finden schriftliche Anfragen und Vor-Ort-Pr?fungen durch den Medizinischen Dienst der Krankenversicherungen (MDK) statt. Diese spiegeln in ihren Ver?nderungen sowohl die Erfahrung der Kassen mit dem G-DRG-System (G-DRG German Diagnosis Related Groups) als auch der zust?ndigen ?rztlichen Mitarbeiter und des Krankenhauscontrollings wider. Wir wollten aufarbeiten, welche Entwicklung die MDK-Pr?fungen seit 2005 genommen haben. Hierf?r wurden s?mtliche Pr?fberichte seit Einf?hrung der Pr?fungen ausgewertet. Ergebnisse W?hrend anfangs haupts?chlich Fragen zur Kodier- und Dokumentationsqualit?t erfolgten, werden jetzt ?berwiegend Fehlbelegungspr?fungen durchgef?hrt. Zwischenzeitlich wurden konsequent die unterschiedlichen Klinikbereiche gepr?ft. Die Anfragen ...
More than 200 years after the birth of the steam engine, the first thermal engine ever invented, thermal engines such as steam turbines, gas turbines or internal combustion engines are still driving most generators for electric power generation, most machines, and most vehicles, and this will remain so until far into the next century. (orig.) [Deutsch] Mit Waermekraftmaschinen wie Dampfturbinen, Gasturinen und Verbrennungsmotoren werden auch heute - mehr als 200 Jahre nach der technischen Reife der Dampfmaschine (der ersten Waermekraftmaschine) - die meisten Generatoren zur Stromerzeugung, die meisten Arbeitsmaschinen und die meisten Fahrzeuge angetrieben. Und dabei wird es auch bis weit in das 21. Jahrhundert bleiben. (orig.)
In parking areas of large extent, the removal of engine exhaust gases, especially of their CO gas components with ventilation plant is mainly done by transverse ventilation over short paths. By their presence, the ventilation ducts required for this purpose often reduce the value of the parking space by restrictions with a consequent reduction of their acceptance by the users. Longitudinal ventilation without ducts can be a remedy in such cases. Depending on the required room air quality in the zones of highest loading, the volume flows with longitudinal removal are no greater than with conventional transverse ventilation. This article is concerned with the different methods of operation of the two systems. (orig./BWI)
Two of the working sessions of the meeting were devoted to aspects of international atomic energy law; the international character of the meeting was also reflected by the home countries of the members of the panel discussion concluding the working sessions. There was substantial reason to put emphasis on the international dimension of the topics discussed. In June 1994, the Nuclear Safety Convention had been signed in Vienna by diplomatic representatives of the signatory countries, and this Convention marks a signpost in the history of international atomic energy law. At the time the meeting was held, negotiations for improving the international nuclear lability law, which had been dragging on since 1989, had come to a stalemate. The meeting offered a suitable forum for taking a scientific approach to tackle the complex problems involved in reshaping the law on nuclear safety and nuclear liability. The third working session of the meeting has been discussing topics relating to the ...
A process model is presented and used for identifying options for controlling the cupola furnace process and for investigating natural gas substitutes. Fuel substitution will affect temperature curves (i.e. tapping temperatures and melting capacity), outlet temperatures and gas mass flow out of the preheating zone. The contribution presents several process variations to overcome these problems and compares them with the natural gas process. [German] Mit dem Prozessmodell werden zunaechst Moeglichkeiten der Steuerung von Abstichtemperatur und Schmelzleistung, insbesondere unter Beruecksichtigung der Schrottqualitaet (spezifische Oberflaeche a{sub G}), untersucht. Es wird gezeigt, dass das Prozessmodell die Ergebnisse aus der Praxis wiedergibt. Daran anschliessend wird mit dem Prozessmodell die Substitution von Erdgas durch minderwertige Gase untersucht (Brennstoffsubstitution, Ressourcenschonung). Durch die Brennstoffsubstitution veraendern sich die Temperaturverlaeufe und damit auch ...
In addition to dependable starting - even at extreme sub-zero temperatures - the starting behaviour of modern commercial vehicle diesel engines is increasingly being evaluated on the basis of HC emissions in the starting and warm-up phases. To improve their performance in this respect, most small and medium-sized diesel engines (with a capacity of 3 to 12 litres) are therefore equipped with intake air heating systems. As an alternative to high-performance, fuel-burning flame start systems, the automotive industry supplier Beru has now developed a new type of self-regulating electric heating element which not only ensures dependable starting with short heating times but also allows drastic reductions in HC emissions. (orig.) [Deutsch] Das Startverhalten moderner Nutzfahrzeug-Dieselmotoren wird, ergaenzend zum Hauptmerkmal des sicheren Starts auch bei extremen Minustemperaturen, zunehmend anhand der HC-Emission in der Start- und Warmlaufphase beurteilt. Zur ...
FLUTAN is a highly vectorized computer code for 3-D fluiddynamic and thermal-hydraulic analyses in cartesian and cylinder coordinates. It is related to the family of COMMIX codes originally developed at Argonne National Laboratory, USA. To a large extent, FLUTAN relies on basic concepts and structures imported from COMMIX-1B and COMMIX-2 which were made available to KfK in the frame of cooperation contracts in the fast reactor safety field. While on the one hand not all features of the original COMMIX versions have been implemented in FLUTAN, the code on the other hand includes some essential innovative options like CRESOR solution algorithm, general 3-dimensional rebalacing scheme for solving the pressure equation, and LECUSSO-QUICK-FRAM techniques suitable for reducing `numerical diffusion` in both the enthalphy and momentum equations. This report provides users with detailed input instructions, presents formulations of the various model options, and explains by means of ...
The comprehensive survey explains the indications and the specific value of the modern tomographic modalities with respect to the various diagnostic issues. Numerous reproductions of CT, MRI, US scans illustrate the aspects discussed. (orig./CB) [German] Bildgebende Verfahren kommen bei der Abklaerung von Erkrankungen des weiblichen Urogenitaltrakts ergaenzend zu der klinischen Untersuchung zur Anwendung. Kongenitale Uterusanomalien werden primaer mit der HSG oder der Laparoskopie diagnostiziert. Zusaetzlich koennen der transvaginale US und in unklaren Faellen die MRT eingesetzt werden. Die Diagnose entzuendlicher Erkrankungen des weiblichen Genitaltrakts erfolgt in der Regel klinisch. Schnittbildverfahren werden bei therapieresistenten, komplizierten Faellen angewendet. Initial werden benigne Neoplasien des Uterus mit dem transvaginalen US abgeklaert. Eine Verdickung des Endometriums ist dabei ein unspezifischer Befund und kann auf eine Hyperplasie, Polypen oder ...
T{sub 2} weighted ultra-short turbo spin echo sequences were used in five individuals with variations in echo times, delayed triggering and echo intervals. To reduce movement artifacts all examinations were carried out with ECG and respiratory triggering. The sequences giving optimal image quality were then employed in 19 patients having various pulmonary abnormalities. Image resolutions, artifacts, image contrasts and diagnostic value were then judged by two observers and compared with CT. In the first study, a diastole-triggered UTSE sequence with the shortest echo proved optimal (T{sub E}=90 ms, T{sub R}=2-4 s, echo=9 ms, turbo factor=19). In the patient series studied, MRT was inferior to CT with regard to resolution and number of artifacts, but better in respect of contrast and diagnostic value. Using UTSE of the lung, MRT can produce images of good quality. Compared with CT, contrast is better with MRT, offering diagnostic advantages for MRT. (orig./MG) [Deutsch] Zuerst wurde an ...
Rehabilitation of the abandoned uranium mining areas in Saxonia and Thuringia is a task posing also legal problems. The radiation protection laws of the former GDR continued to be effective to a great extent and proved to be a legal basis not ``perfect`` in formal terms, but suitably efficient in practice to tackle the manifold problems encountered in the land reclamation and waste disposal work. Originally intended to serve as a legal interim regime awaiting amendment at a later date, the body of laws available for the task proved to be a sufficient basis. (orig./HP) [Deutsch] Das fortgeltende Strahlenschutzrecht der frueheren DDR hat sich zwar nicht als formal `perfektes`, in der Sache aber strahlenschutzgerechtes und praktikables Instrument zur Loesung der anstehenden Sanierungsaufgaben erwiesen. Bei seiner Beurteilung darf nicht ausser Acht gelassen werden, dass die Ueberleitung dieses Rechts seinerzeit aus der Not eines kurzfristigen ...
The pilot project of the conversion of the green forage drying plant Lengenfeld to biomass firing could not be realized without problems. But the experience until now shows that it is in principle possible. The farmers involved are devoted to the project. For them the cultivation of biomass is an alternative to the abandonment of fields. The present low oil price sets limits to the positive income effect. The aim is an increase of the biomass share in heating energy supply to about 80%. (orig.) [Deutsch] Die Umstellung der Gruenfuttertrocknung Lengenfeld auf Biomassefeuerung ist als Pilotprojekt nicht ohne Probleme moeglich gewesen. Die bisherigen Erfahrungen zeigen jedoch die grundsaetzliche Praktikabilitaet. Die beteiligten Landwirte sind engagiert bei der Sache und schaetzen die Produktionsmoeglichkeit als Alternative zur Flaechenstillegung. Der derzeit niedrige Oelpreis setzt der positiven Einkommenswirkung jedoch enge ...
For purposes of assessing the dumpability of wastes, Article 1 - Ordinance on the Environmentally Responsible Landfilling of Household Wastes (AbfAblV) - of the Ordinance on the Environmentally Responsible Landfilling of Household Wastes and Biological Waste Treatment Plants defines classificaton criteria for biologically and mechanically treated wastes destined for landfilling. The practical experiences that have been gathered with these classification criteria and values were evaluated in a questionnaire-based survey. This was done in particular for the purpose of verifying and validating proposals on the methodology of respiration and fermentation tests. A general finding has been that the application and implementation of the regulations of the AbfAblV is fraught with difficulties. This is evident for one thing in the frequency of analyses and for another in the difficulty of complying with the limit values of the classification criteria. The authors are in support of demands that ...
The basis of assessment for particulate exhaust emissions is the gravimetric analysis of the particle concentration of diluted exhaust gases at temperatures below 52 C. This is very time consuming and takes sufficient sensitivity at low particulate emission rates like downstream of particle filters. For this reason the C/S-method, based on the thermographic analysis of carbon and sulfur, has been developed as an alternative to the gravimetric anallysis. This method yields particle mass as well as the main particle compounds. Comparisons between both methods have been carried out for heavy duty and automobile diesel engines as well as road vehicles and large diesel engines. The tests were conducted with commercial diesel fuel and also with other fuels, such as heavy oils. It could be shown that the C/S-procedure yields the same results as the gravimetric procedure independent of engine, engine mode and kind of fuel. The analysis of all important particulate compounds - elemental carbon ...
Only about 25% of residue accumulating in the Federal Republic of Germany is currently used for the purposes of energy. This residue will be converted into fuel for power stations by the Omega process when the dumping of waste with a calorific value in excess of 5 MJ/kg is prohibited with effect from 2005. This oxygen melting process is suitable for the local use of substitute fuels. Waste is converted into a high-quality synthesis gas with a wide range of uses. The Omega process combines drying, thermal decomposition, gasification and melting of the material used in a single-stage process. This is now technologically possible for the first time by combining a metallurgical cupola furnace with a traditional gas producer. The highly-calorific synthesis gas produced by the Omega process can be used in block heat and power stations or as an industrial fuel gas, instead of natural gas. It is also suitable as a starting material for synthesising methanol. The gas is specifically processed ...
Nuclear medicine and magnetic resonance imaging (MRI) are widely used in cardiac diagnostics. Both techniques have been carefully evaluated and are equivalent for the assessment of regional and global wall motion as well as the evaluation of ejection fraction and cardiac volumes, though MRI is herein currently seen as gold standard. For evaluation of myocardial perfusion, extensive data exist for nuclear imaging, that, next to high diagnostic accuracy for evaluation of coronary artery disease, show incremental prognostic information and allow for independent risk stratification. Because of rapid technical advance, myocardial perfusion imaging has also become feasible with cardiac MRI. Results of recent studies are promising, but the data are few compared to perfusion scintigraphy. For viability assessment in patients with ischemic cardiomyopathy, positron emission tomography (PET) with FDG is currently seen as gold standard. However, single photon emission computed tomography (SPECT) ...
Within its competence for energy research, the Bundesministerium fuer Wirtschaft und Arbeit (BMWA) (Federal Ministry of Economics and Technology) sponsors investigations into the safety of nuclear power plants. The objective of these investigations is to provide fundamental knowledge, procedures and methods to contribute to realistic safety assessments of nuclear installations, to the further development of safety technology and to make use of the potential of innovative safety-related approaches. The Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, by order to the BMWi, continuously issues information on the status of such investigations by publishing semi-annual and annual progress reports within the series of GRS-F-Fortschrittsberichte (GRS-F-Progress Reports). Each progress report represents a compilation of individual reports about the objectives, work performed, results achieved, next steps of the work etc. The individual reports are prepared in a standard form by the ...
The first volume of the report covers the state of implementation of primary and secondary measures for SO{sub 2}- and NO{sub x} control applied in the most important industrial sectors in Germany. Integrated pollution abatement techniques, called primary measures in this report, such as process integrated measures and low emission processes, have gained increased importance in recent years. The end-of-pipe processes, described here as secondary measures, are generally highly effective. They represent mature technologies, which are capable of achieving significant reductions in SO{sub 2}- and NO{sub x} emissions, and which have been used in particular for retrofitting existing plants. At first, an overview is given regarding the development of SO{sub 2}- and NO{sub x} emissions in selected European countries during the last 20 years and in Europe. Current national and European emission limits and emission guidelines on SO{sub 2}- and NO{sub x} emissions from stationary sources are ...
As one of the largest contractors for the construction of ethylene plants featuring steam cracker furnaces as their core component Linde AG has examined the `real` chemical recycling of polymers in steam cracker furnaces as an alternative to their thermal utilisation. In steam cracker furnaces the feedstock, i.e., hydrocarbons, is broken down to ethylene, propylene, and other valuable products in a steam dilution of approx. 800-870 C. In the ideal case, if polyolefins are used as feedstock, then the initial product which led to the polymers can be fully recycled. In this context a series of experiments was carried out in a laboratory-scale cracker plant. The purpose of this was to demonstrate the technical feasibility and the economic advantage of using recycling polyethylene or polypropylene as feedstock for steam cracker plants. (orig./SR) [Deutsch] Die Linde AG als einer der bedeutendsten Kontraktoren fuer den Bau von Ethylenanlagen, deren Herzstueck die ...
To study the biogeochemical behaviour, mobility and transport of trace metals in seawater (Se, Mo, Cd, Pb, Hg, Cu, Co, Fe, Ni, Zn), in suspended particulate matter (Mo, Cd, Pb, Cu, Co, Fe, Ni, Zn, Al, Mn) and in sediments of the inner and outer coastal regions, samples were collected on 3 separate cruises during a one year period (Mai 1993 - April 1994) at 20 stations in the coastal area of Mecklenburg-Vorpommern. Standard hydrographic parameters, nutrients and dissolved oxygen were also measured. Priority was taken to establish the methods for the determination of molybdenum and selenium. To study the behaviour of these two elements in detail, longterm measurements were carried out weekly between January 1993 and June 1994 at the `Messsteg/Warnemuende`. Because of parallel measurements correlations to biological, chemical and hydrographic parameters have been tested. The total database is summarized in the Appendix. The results are presented in 30 figures and 13 ...
Present day mammography has not been able to make use of the advantages of digital luminescence radiography because of the limited spatial resolution. The recent development of electromagnetic focusing X-ray tube with effective focal spot sizes from 0.04 to 0.12 mm allows radiographic direct magnification with less geometric blur. It is now possible to combine direct magnification mammography with digital luminescence radiography. By combining high quality storage phosphor screens with an HQ-workstation a spatial resolution of 8 lp/mm is possible for 1.7-fold magnification. For 4-fold spot magnification views spatial resolution can be theoretically increased to approx. 20 lp/mm. One important advantage of digital radiography is the possibility of image-postprocessing. This article presents two sets of standard parameters and three sets of image dependent parameters for better imaging of specific lesions, such as microcalcifications. The introduction of the storage phosphor screen ...
Minimally invasive thermotherapies for focal tissue destruction on the basis of laser-, microwave-, focused ultrasound-, or cryogeninduced changes of tissue temperature represent an alternative to surgical tissue ablation, particularly in the treatment of tumors. The thermotherapy modalities listed necessitate indirect guidance and monitoring, since they often do not lend themselves to immediate visual control. In the brain, in head and neck tumors, in the liver, and in the prostate, MRI reliably and accurately delineates both the positions of interstitial thermotherapy applicators and - in contrast-enhanced, T1-weighted images - the perfusion defects in tissue necrosis induced by thermotherapy. The transfer of results of in-vitro and in-vivo model studies to assess interstitial temperature and lesion development during thermotherapy to the actual treatment of patients, however, is still in an initial phase. Further development of both rapid MRI sequences and MRI scanners suited for ...
Against the background of more severe limitation of particle emission in all application areas of Diesel engines, it is necessary to monitor the particle emission, but also the chemical composition of the particles. The basis of assessing particle emission is formed by gravimetric determination of the particle concentration from exhaust gas diluted with particle-free ambient air, with a maximum temperature of 52 degrees C at the sampling position. While it is already possible, using the part flow dilution system, to take samples locally, previously the subsequent particle determination and characterisation could only be done in a chemical laboratory. For this reason, the C/S particle measurement process was developed as an alternative to gravimetry, which can be used locally, eg: on ships and which makes it possible to determine the particle mass and composition. This process is based on a thermographic carbon and sulphate determination. Comparative investigations were done both on ...
This update of a system concept entitled ``Maritime hazard prevention and water protection`` makes full use of the technical room for maneuver while considering that reasonable financial and economic conditions must be provided. The update allows on to continue or start the exploitation of feasible technical, logistic and information-technology development potentials. The same applies to the national maritime traffic safety measures developed for the German waterways. Considering the maritime hazards that have been prevailing in the coastal areas of the German North Sea, the conducted damage risk investigations suggest that a large-scale, disastrous oil contamination of the mud flats ecosystem cannot be excluded or controlled definitely in spite of the numerous measures taken. (orig.) [Deutsch] Mit der vorgelegten Fortschreibung zum Systemkonzept ``Gefahrenabwehr und Gewaesserschutz im Seeverkehr`` werden die technisch realisierten Handlungsspielraeume unter Beachtung der finanziellen ...
Damage survey of protective coats of modern gas turbine blade shows that most damages are not due to classic wear mechanisms such as oxydation or high-temperature corrosion but caused by foreign bodies, poor coating during manufacturing, or operation-caused cracks. Mere visual inspection of cracks is often not sufficient to tell whether cracks are superficial or whether they have already progressed into the base material. Non-destructive methods such as ultrasonic inspection or eddy-current testing are helpful tools but there is not yet a fully matured testing concept at hand. Metallographical tests can give important information about crack mechanisms and thermal, chemical and mechanical stresses.(orig.) [German] Die Schadenerfahrung mit Schutzschichten moderner Gasturbinenschaufeln zeigt, dass die meisten Schaeden nicht auf die klassischen Verbrauchsmechanismen wie Oxydation und Hochtemperaturkorrosion zurueckzufuehren sind, sondern durch Fremdkoerper, herstellungsbedingte ...
Heat pumps for residential space heating become an increasingly important alternative to the conventional heating system like gas or oil burner. They offer the opportunity to reduce CO{sub 2} emission associated with heating residential homes in Germany. High compressors efficiency and a wide operating map are required so that an economically viable heat pumps is achieved which meets the operational conditions for present and future heating systems. The design parameter of existing heating systems require relatively high condensing temperatures which can be achieved with dedicated compressor designs. The design of Scroll compressors specially adapted to these heat pumps is shown and their operation is explained. (orig.) [German] Waermepumpen fuer die Wohnraumheizung gewinnen an Bedeutung als Alternative zur konventionellen Gas- oder Oelheizung. Sie bieten die Moeglichkeit, die mit der Gebaeudeheizung verbundene Emission von Kohlendioxid in ...
With the development of the latent heat store and its inclusion in the conventional heating control of cars, success has been achieved both in increasing comfort and in making an important contribution to safety of driving. Great store is set in development of the system on its environmental friendliness, for example by the thorough use of environmentally friendly and reusable materials. This also means the use of clean materials. It was shown that the latent heat store (apart from the aspects of comfort and safety of driving) can also make a contribution to saving fuel and reducing the exhaust gas. The sum total of the advantages makes it clear that the latent heat store introduced here is a very environmentally friendly system with multi-functional properties. (orig.) [Deutsch] Mit der Entwicklung des Latentwaermespeichers und seiner Einbindung in die konventionelle Heizungsregelung von Automobilen ist es gelungen, sowohl den Komfort deutlich zu erhoehen als auch ...
The textbook is primarily intended for radiologic staff and radiologic safety officers and gives information on the current regulatory provisions of the German X-ray Ordinance, applications of X-rays, quality assurance, organisational aspects of film processing and quality requirements of X-rays. An annex lists the guidelines of the Bundesaerztekammer (German National Chamber of Physicians) relating to quality assurance aspects, and further useful information on commercially available film-screen systems, the various associations of physicians in Germany, and requirements and performance of radiation surveys. (vhe) [Deutsch] Das vorliegende Lehrbuch, das sich vor allem an das technische Personal und an Strahlenschutzbeauftragte wendet, unterrichtet ueber die derzeit gueltigen Bestimmungen der Roentgenverordnung, die Anwendung von Roentgenstrahlen, ueber Qualitaetssicherung, die Organisation der Filmverarbeitung sowie ueber die Anforderungen an die Qualitaet von Roentgenbildern. Im ...
The book is a German translation of an American textbook with the original title ''MRI Survival Guide'' and is intended to serve as an introductory guide for beginners or a reference book for quick information. Readers will find information on the fundamentals of the technology and methodology of MRI as well as all details of relevance to practice in a precise and easy-to-grasp arrangement, covering all anatomic areas of interest, illustrations and descriptions of characteristic signs of pathologic processes, high-quality and unusually large-sized diagnostic pictures, a modern didactic concept for quick orientiation, including surveys, tables, and reproductions for visualisation of contents. (orig./CB) [German] Praktisch jeder Mediziner wird im Laufe seiner Berufstaetigkeit mit der MRT konfrontiert - unabhaengig davon ob in der Radiologie, Orthopaedie, Gynaekologie, Chirurgie, Neurologie oder sonstigen Fachrichtung. Das Buch ist eine Uebersetzung ...
As an alternative to surgery, endovascular therapy with stent grafts has become the second main treatment option for infrarenal abdominal aortic aneurysms. Unlike surgery, endovascular treatment with stent grafts is also applicable in patients unfit for open repair. Despite current improvements in endovascular repair devices, significant anatomic barriers still exclude this technique for a large number of patients. Computed tomography, magnetic resonance imaging, and ultrasound are essential for diagnostics, preintervention planning, and postintervention follow-up of abdominal aneurysms treated with stent grafts. This review covers etiology, pathology, and diagnostic aspects. Materials and methods for endovascular treatment of abdominal aortic aneurysms are presented in detail, and clinical results and complications are discussed. (orig.) [German] Die endovaskulaere Therapie des infrarenalen Bauchaortenaneurysmas hat sich als Alternative zur ...
In 1986, following comprehensive preliminary studies, a 17 MW battery energy storage plant was set up in the insular power supply system of Berlin (West) for the purpose of frequency and output control and provision of immediate reserve capacities. The present paper reports on the initial task, and the dimensioning and construction of this large-scale demonstration as well as the costs entailed in this. It also relates the experiences gained with the operation of the battery energy storage plant in its function as a fast-responding control unit and gives an account of its economic efficiency. Recent studies on the economic efficiency of the plant in conditions as they exist in the present interconnected power supply system are presented. Finally the author reports on the experiences gained with individual plant components, i.e., battery, battery periphery, and power converter and quantifies the cost of plant operation, maintenance, and servicing. (orig./HW) [Deutsch] Im Inselnetz von ...
The stirling cryocooler ILK 15 is a machine with simple drive concept. This machine works with a conventional built-in electric motor and crank drive and needs a power input of about 500 W. The refrigerating capacity is 15 W at 80 K with a cooldown time of 12 minutes. The cooler is somehow a replacement for the Gifford-McMahon cycle coolers, which are bigger and heavier. The Stirling cryocooler was designed to cool HTSC-components. (orig.) [Deutsch] Der Stirlingkuehler ILK 15 ist eine Kaeltemaschine mit einfachem Antriebskonzept. Die Maschine arbeitet mit einem konventionellen Elektroeinbaumotor und Kurbeltrieb. Sie benoetigt eine Antriebsleistung von 500 W und hat eine Kaelteleistung von 15 W bis 80 K und eine Einkuehlzeit von 12 Minuten. Die Maschine kann als Alternative zur wesentlich groesseren und schweren Gifford-McMahon-Maschine gesehen und bei der Kuehlung von HTSL-Komponenten eingesetzt werden. (orig.)
Magnetic fields can be compensated by opposing fields. This principle can be applied for reducing the magnetic fields emanating from high-voltage transmission lines or found in residential or commercial buildings. The article shows a number of concrete options for reducing magnetic fields in the vicinity of high-voltage lines through appropriate conductor configuration on the one hand, and a novel method using Helmholtz coils for compensating those fields in buildings. (orig.) [Deutsch] Magnetische Felder koennen durch Gegenfelder kompensiert werden. Dieses Prinzip laesst sich sowohl auf Hochspannungsleitungen als auch auf Wohn- und Arbeitsraeume uebertragen. Der Artikel zeigt konkrete Moeglichkeiten, wie einerseits Magnetfelder von Hochspannungsleitungen durch eine geeignete Konfiguration der Leiter reduziert werden koennen, und beschreibt andererseits eine neue Methode zur Reduktion solcher Felder in Wohn- und Arbeitsraeumen mittels ...
Plasma Immersion Ion Implantation (PIII) is a new hybrid technology for surface treatment of materials based on the principles of plasma nitriding and ion implantation. The equipment and the operation of the system are introduced. As well as providing an alternate method of ion implantation, it is possible to combine energetic ion bombardment with plasma nitriding. Different metal materials and treatment conditions have been studied. The capability of PIII-treatment to improve the properties of a wide range of metals has been proven. Application for forming tools and their industrial test has been successful. (orig.) [Deutsch] Die Plasmaimmersionsimplantation (PIII) ist eine neue Hybridtechnologie zur Behandlung von Werkstoffoberflaechen und basiert auf den Prinzipien des Plasmanitrierens und der Ionenimplantation. Die Anlagentechnik und die Arbeitsweise werden vorgestellt. Verfahrensspezifische Vorteile entstehen durch die Moeglichkeit, sowohl alternative ...
The liberalisation of the energy markets requires completely new demands to the information processing procedure of energy supply enterprises. These requirements are to be understood as chances for strengthening of the terms of competition. In the following contribution to this subject the actual status of the concept as converted by the Electricity Supply Company of Halle (Saale) including their departments of district heating, gas and electricity supply will be presented. This concept are comprising all experiences as gathered so far as well as intended further actions to be executed. (orig.) [German] Die Liberalisierung der Energiemaerkte stellt fuer Versorgungsunternehmen voellig neue Anforderungen an die Informationsverarbeitung. Diese Anforderungen sind als Chancen zur Staerkung der Wettbewerbsfaehigkeit zu verstehen. Die Verfasser erlaeutern den aktuellen Stand des in der EVH GmbH Halle (Saale) im Querverbund der Sparten Fernwaerme, Gas ...
In car parks of considerable length, the removal of exhaust emissions, is carried out by air-conditioning systems mainly through transverse ventilation over short routes. The required air-conditioning ducts frequently produce a reduction in the available parking space simply due to their presence, resulting in restrictive effects on the level of acceptance by the users. In such cases, remedial action can be taken by creating ductless longitudinal ventilation. Depending on the required room air quality in the zones with the highest level of pollution, the volumetric flows for longitudinal disposal are no greater than those for conventional transverse ventilation. In conjunction with architecturally clear and positive lighting designs, clearly laid out car parks with a friendly atmosphere can be created which the user will be pleased to accept. (orig./BWI)
A new material has been developed for welded low-pressure shafts in steam turbines. Nine test welds were examined in order to confirm the chemical analysis. A shaft disc with an optimized composition was produced and destructively tested. The new material demonstrates, both in a total forging and also in a joint weld examined, excellent strength and toughness characteristics as well as excellent resistance to corrosion. Accordingly, all the requirements for welded low-pressure shafts in steam turbines are fulfilled. (orig.) [Deutsch] Fuer geschweisste Niederdruckwellen in Dampfturbinen wurde ein neuer Werkstoff entwickelt. Zur Festlegung der chemischen Analyse wurden 9 Versuchsschmelzen untersucht. Mit optimierter Zusammensetzung wurde eine Wellenscheibe hergestellt und zerstoerend untersucht. Der neue Werkstoff zeigt sowohl im gesamten Schmiedestueck als auch in einer untersuchten Verbindungsschweissung gute Festigkeits- und ...
Problems with the refractory liners of incinerator combustion chambers have accompanied incinerators from the very beginning. They increased during the past decade, owing to higher combustion temperatures required by law (17. BImSchV), the higher calorific values of the waste to be combusted, and the higher or changed pollutant concentrations in the waste materials. This caused the providers and the materials and the producers of incinerators to develop new refractory products and new design concepts, with a great variety of processes and cost levels. [German] Seit Beginn der Abfallverbrennung, insbesondere aber mit zunehmender Tendenz in den vergangenen 10 Jahren, wird ueber Probleme mit der Feuerfestauskleidung in den Brennkammern von Abfallverbrennungsanlagen geklagt. Als Gruende fuer die zunehmenden Korrosionsprobleme werden die hoeheren gesetzlich geforderten Verbrennungstemperaturen (17. BImSchV), die hoeheren Heizwerte der verbrannten Abfaelle und die ...
High temperature components of power plants are in many cases subjected to variable loading conditions such as cyclic creep or strain cycling. Therefore the cyclic behaviour of important heat resistant steels has been investigated under stress control and to a smaller extent under strain control. The behaviour under cyclic creep rupture conditions was determined in long term experiments covering a wide range of loading conditions. This behaviour can be described with the modified life fraction rule and a factor concept of relative life for single stage cycles and additionally with a multistep hypothesis for multi-stage cycles. The description can be adapted to estimate the life consumption under service type random conditions. The strain cycling behaviour was investigated in regard to the conditions of the heated surface of large components. To simulate this type of loading and to generate long term creep fatigue data, a service type strain cycle was developed. Anisothermal and ...
To determined precisely a possible connection between the amount of copper in tap-water and the risk of early childhood liver disease, it was attempted through an epidemiological survey, to determine the extent of excessive concentrations of copper in the tap-water of households with copper pipes. Water samples from 956 households were tested for copper, and the state of health of the infants in these households was documented. Infants who had been fed using water with a copper concentration of 0.8 mg/l or more received a paediatric examination with a blood serum analysis to rule out any liver damage. A copper level greater than 0.8 mg/l was found in only 2% of the households examined. Eight infants were examined by a paediatrician and their serum was analysed. These infants had either been breast-fed to the 12th week or had received more than 200 ml of tap water per day during first 12 months. None of the infants examined showed any signs of liver malfunction. From the results of the ...
This report completes the documentation for the research project 'High Pressure Compressor - Preliminary Design as Basis for the Development of an Efficient and Environmentally Friendly Core Engine' which was funded by the Ministry of Economics of State Brandenburg. The objective of the project is to deliver a preliminary compressor aerodynamic design as well as design studies for an efficient, weight and cost improved compressor. The increase of stage pressure ratio and improved efficiency, whilst stage and blade count is reduced, has been achieved by advanced 3D methods. Compressor stability also at off-design conditions will be retained. The mechanical design focusses on a cost and weight optimised rotor not only for a conventional bladed discs but also for Blish stages. Various options for split casings have been developed and assessed. Alternative vortex reducers based on different design options have been carried out. The results from this project will be ...
MRI provides a non-invasive diagnostic tool complementing echocardiography on one hand, and showing advantages over echocardiography, on the other hand, especially after corrective procedures. The multiple different MRI sequences need to be adapted to examinations of children and patients with congenital heart disease (CHD), and can be used to detect morphologic changes, blood-flow in the heart and thoracic vessels and diastolic or systolic function of myocardium. Several factors determine the success of the examination of a complex congenital heart disease or a postoperative situs. Pediatric radiologists and radiologists experienced in congenital heart diseases have to work in close cooperation. Echocardiography should be performed before MRI. The results of prior examinations and the clinical history of the patients, including possible palliative or reconstructive operations, must be available before MRI to guide the planning of the examination. With a systematic segmental approach ...
The paper addresses the major items of relevance to compensation for nuclear damage under civil liability law. The revision of the Vienna Convention deserves support as a contribution to enhancing the protection of those who suffered damage, and of the environment. The results of the revision will have an impact on the liability regimes in existing and future signatory states, and to some extent will also set the goals of a future reshaping of the Paris Convention, all the more since the Joint Protocol calls for harmonization of at least basic provisions of substantive law in the two Conventions. (orig./HP) [Deutsch] Es werden die wesentlichen Punkte dargestellt, die fuer die zivilrechtliche Praxis im Schadensfall von Belang sein koennten. Die Revision ist als Beitrag zu einem verbesserten Schutz Geschaedigter, aber auch der Umwelt zu begruessen und zu unterstuetzen. Die Ergebnisse werden sich auf die Rechtsordnungen der gegenwaertigen und zukuenftigen ...
The interdiffusion behaviour of MCrAlY-coats on polycrystalline and single-crystalline materials of a similar composition (IN 738 LC/SC 16)shows similar interdiffusion characteristics. TCF-tests, where stress is generated by temperature and sample geometry at the edges of a disk-shaped sample, show that it is possible to differentiate betwee crack resistance of coated and uncoated samples. This method is also suitable for screening tests with different coat thicknesses. Coating of the edge area must, however, be done with great diligence in order to prevent coat thickness variation as results would then not be reproducable. Contrary to TCF (thermal cycle fatigue) TMF-tests (thermal mechanical fatigue)allow to set the stress states that one wishes to test. This method is therefore well suited for testing under operating conditions.(orig.) [German] Im Rahmen dieser Arbeit wurde gezeigt, dass das Interdiffusionsverhalten von MCrAlY-Schichten auf ...
The thesis explains the development of a mass spectrometerical isotope dilution analysis (MS/DA) for determining trace amounts of Tc. The Tc-97 isotope has been prepared by in-core irradiation of Ru of natural isotopic composition, and used as the indicator isotope. For separation of Tc-97 from the Ru matrix, a method has been developed to quantitatively separate Tc-97 from a high Ru surplus. For determining the isotope ratio for the MS/DA, a mass spectrometrical measuring technique has been found which allows reproducible measurement of the Tc-99/Tc-97 isotope ratio. Positive and, for the first time, also negative thermoionisation has been used as a method of selective ionisation of Tc. The applicability of the MS/DA for Tc trace analysis has been verified using two Al foils doped with Tc-99 or Mo-98, respectively. These have been irradiated in a nuclear reactor, the irradiation of Tc-99 yielding Ru-100, and irradiation of Mo-98 Tc-99. The determination of the ...
The spent fuel management concept of direct ultimate disposal is compatible in its fundamental features with the law of the European Community. This applies to a national law prohibiting spent fuel reprocessing and the handling of plutonium in Germany, imposing restrictions on exporting spent fuel assemblies and importing plutonium and reprocessing remnants, and on power plant operators to employ reprocessing services abroad. Also, a nuclear power phase-out decided by the German government would in principle not mean a breach of the EURATOM treaty. (orig./HP) [Deutsch] Als Alternative zur geltenden Rechtslage werden im Deutschen Rundestag Aenderungen vorgeschlagen, die das Entsorgungskonzept der direkten Endlagerung - d.h. ein Verbot der Wiederaufarbeitung von Brennelementen aus deutschen Kernkraftwerken auch im europaeischen Ausland - vorschreiben und einen ``Ausstieg`` aus der Kernenergienutzung anordnen. Vor dem Hintergrund einer Analyse der ...
As an alternative to the usual way of installing wind machines in extended windfarms new concepts are being developed. Several wind turbines are affixed to one support structure and can be aligned together. Drafts of steel constructions developed by students in three diploma theses are presented. The attempt to transform existing design standards requires extensive discussion of possible influence scenarios. Several concepts regarding structure and safety elements are described and evaluated. The design of the support structure is to be seen as a first step to the practicability of the whole concept. A preliminary mass calculation and a specification of further cost factors facilitates the comparison to conventional wind power stations. (orig.) [Deutsch] Als Alternative zur ueblichen Praxis, Windenergieanlagen in Form grossflaechiger Windparks zu bauen, werden Konzepte entwickelt, bei denen mehrere Konverter an einem Tragwerk angeordnet und ...
Policy strategies for the promotion of electricity from renewable energy sources differ significantly among the Member States of the European Union with respect to the amount of additional installed capacity as well as concerning the country-specific support costs. The present report aims to assess the effectiveness and the economic efficiency of the support policies in the EU based on both historical experiences and prospective model-based analysis. The main message of the investigation is that the most effective policy instruments tend to be cost-efficient at the same time. In particular, feed-in tariff systems were identified as a successful instrument for supporting renewable energies in terms of effectiveness and efficiency, whereas quota systems still have to prove themselves in practice. (orig.) [German] Bezueglich des Erfolges bei der Foerderung erneuerbarer Energietraeger im Stromsektor bestehen deutliche Unterschiede zwischen den Mitgliedsstaaten der Europaeischen Union. Dies ...
The typical MRI features of the most common pancreatic diseases, such as pancreatitis and adenocarcinoma of the pancreas, have been established. However, even in these common pancreatic disorders, MRI correlation with the underlying pathology is limited for clinical reasons. We emphasize MR-pathological correlation of inflammatory and neoplastic pancreatic changes, including pancreatitis, adenocarcinoma, acinar cell carcinoma, rare cystic and solid pancreatic neoplasms, and islet cell tumors. By highlighting the correlation of key pathological features with MR findings, a better understanding of the MR appearance of pancreatic pathology can be provided. In addition, MRI may prove a powerful tool in detection and characterization of pancreatic tumors. (orig.) [Deutsch] Das MR-tomographische Erscheinungsbild von Pankreatitiden und Adenokarzinomen des Pankreas, als den haeufigsten Pankreaserkrankungen, ist zwar ausreichend bekannt; allerdings ist selbst bei diesen ...
Metal hydrode stores are used as fuel tanks in vehicles or as stationary stores of high-purity hydrogen. Equilibrium isotherms at low pessures were measured in order to validate the laws of Henry or Sievert for hydrogen uptake of the alloy Ti{sub 0.98}Zr{sub 0.02}V{sub 0.43}Fe{sub 0.09}Cr{sub 0.05}Mn{sub 1.5} (patented by Daimler Benz AG, code DB5800). The laws were to provide information on whether hydrogen uptake is atomic or molecular and on the conditions in which isothermal measurements are possible. (orig.) [Deutsch] Metallhydridspeicher werden als Kraftstofftank in Fahrzeuge oder als stationaere Speicher zur Bereitstellung von Reinstwasserstoff verwendet. Fuer diese Arbeit wurden die Gleichgewichtsisothermen bei kleinen Druecken vermessen, um die Gesetze von HENRY oder SIEVERT fuer die Wasserstoffaufnahme in der Legierung Ti{sub 0.98}Zr{sub 0.02}V{sub 0.43}Fe{sub 0.09}Cr{sub 0.05}Mn{sub 1.5} zu pruefen. Anhand dieser ...
The precipitation of heavy metals as hydroxides is the standard technique for the decontamination of waste water streams polluted by these elements. On the other side, progress in research has been made concerning the biosorption onto dead biomass and bioprecipitation supported by physiologically active bacteria. As the aim of this study, a flexible strategy has been envisaged cleaning a waste water with definite heavy metal load underlying the process mentioned above. Suitable bacteria were enriched and the process was tested in a technical plant. As result, a very high efficiency of heavy metal elimination has been found. The field of application covered by the acquired process is identical with the whole range of the waste water streams polluted by heavy metals. In addition, a second stage may be necessary if there are any further contaminants to be removed. (orig.) [Deutsch] Bei der Reinigung von schwermetallhaltigen Abwaessern ist der derzeitige Stand der Technik gegeben durch die ...
Purpose: The nint version of the licensing regulation for medical doctors (Approbation Regulation (AR)) sets a benchmark in terms of practical experience, interdigitation of preclinical and clinical studies, interdisciplinary approach, economic efficiency, independence of students, added new teaching and learning modalities, and ongoing evaluation of the progress of the medical students. It is the aim to implement these major points of the AR in a model course for diagnostic radiology and radiation protection within the scope of the Virtual University of Bavaria and test them in practice. Materials and Methods: In cooperation with residents and board certified radiologists, students developed the virtual course 'Web-Based Training (WBT) Radiology' in diagnostic radiology and radiation protection for students in the first clinical semester. A representative target group taken from the student body was asked about the options to get access to the World Wide Web ...
The European Court of Justice has defined a clear means by which waste utilisation methods can be distinguished from waste disposal methods in a logical, well-understandable manner. With its stringent definition of ''utilisation'' this judgement points the way to quality-oriented waste management practices. We do not share the often voiced fear that this decision will lead to an increased incineration of compound wastes in industrial plants such as cement works. From the fact that, according to the decision by the European Court of Justice, wastes destined for utilisation fulfil a certain purpose and therefore, if not available in sufficient quantity must be replaced by primary raw materials, it follows that these wastes are required to fulfil specific quality criteria. This is rarely the case, if at all, with compound wastes. From the viewpoint of Luxembourg the decision by the European Court of Justice can be regarded as a positive impulse towards ...
DMT has developed what is called the stepped reforming process. This is an allothermal gasification process which uses hydrogen for a gasification medium. First the biomass is pyrolised by means of a heat transfer material. The escaping gaseous and condensable constituents are hydrogenated, heated in a reforming stage and are made to react to a hydrogen-rich product gas by means of homogeneous gasification. The heat required for this is provided by burning the pyrolysis coke. This makes it possible to dispense with process stages that would involve gasification of solid material and hence require higher pressure levels. The present process also works at ambient pressure. Moreover, stepped reforming promises a number of additional advantages: low-tar product gas containing 60% hydrogen, high cold gas efficiency, no wastewater arisings, robust operating behaviour. This paper outlines the basic ideas that led to the development of stepped reforming process and describes its diverse ...
During their life, intervertebral discs undergo degenerative changes which need not necessarily become lesions. Conventional X-rays do not provide information on the condition of the intervertebral discs, so MRT or CT are recommended as primary techniques as they are non-invasive. Invasive methods like myelography and especially discography should not be used unless a case is highly problematic. In infants with pains in the back, MRT should be carried out as early as possible as there is nearly always an organic cause. (orig.) [German] Die Bandscheibe ist im Laufe des Lebens degenerativen Veraenderungen unterworfen, die klinisch zu Beschwerden fuehren koennen, aber nicht fuehren muessen. Konventionlle Roentgenaufnahmen lassen zwar die Hoehenminderung des Bandscheibenfachs und begleitende knoecherne Veraenderungen erkennen, nicht aber den Zustand der Bandscheibe selbst. Die Beurteilung der Bandscheibe und des Knochens gelingt mit der CT, die parallel zum Bandscheibenfach durchgefuehrt ...
Primary malignant lymphoma of the brain is a disease of unknown etiology, which is increasing in incidence and has an unfavorable prognosis. Despite the lack of specific changes on CT or MRI in most cases, these procedures may typically facilitate the diagnosis: A focal-enhancing mass with subependymal spread on CT or MRI and hyperattenuation on nonenhanced CT are the most reliable features in the diagnosis of primary malignant lymphoma of the brain. Peritumoral edema and mass effect are usually not prominent features. On unenhanced CT scans they usually appear homogeneously isodense to mildly hyperdense relative to the gray matter. On MRI these tumors are slightly hypointense on T1-weighted images and slightly hpyerintense on PD- and T2-weighted images relative to the gray matter. On CT and MRI enhancement is usually homogeneous. Contrast-enhanced MRI, with its multiplanar capability, lack of bone-induced artifacts, and high-contrast resolution, is likely to reveal subependymal spread ...
Clinical studies have proved the effectiveness of local ablading methods in pations with non-resectable liver metastases of a colorectal carcinoma. RF ablation and LITT are a potentially curative therapy option and an alternative to systemic chemotherapy; the latter is carried out primarily for reducing tumour size with the goal of secondary resectability. The number of R0-sesectable metastases can be enhanced by a combined therapy of surgery and local ablading methods, e.g. by preoperative, intraoperative or postoperative ablasion of further non-resectable tumours during surgery. Systemic chemotherapy combined with surgery as an adjuvant method is not recommended unless in cases of non-abladable tumour recidivation. Currently, systemic chemotherapy is used as a neo-adjuvant therapy for tumour size reduction with the goal of secondary resectability or, in case of inoperability, local ablation. (orig.) [German] Abladierende Verfahren. Klinische Studien belegen die Effektivitaet der ...
A procedure is described for the isolation and determination of {sup 90}Sr, {sup 226}Ra, {sup 228}Ra and {sup 210}Pb in food. These nuclides are highly radiotoxic, above all for babies and children. Samples are dry ashed, alkali metals are removed as carbonates. Separation from other matrix ions and separation of Ra, Sr and Pb can be achieved with a column of Sr-Spec, an immobilized crown ether. For activity measurements membrane filters with SrSO{sub 4}, Ba(Ra)SO{sub 4} and PbS are prepared. Ra is determined by gamma-spectrometry, {sup 90}Sr and {sup 210}Pb are determined by low-level-betacounting. The determination limits are 10 mBq/kg for {sup 90}Sr and {sup 210}Pb and 50 mBq/kg for {sup 226}Ra and {sup 228}Ra. The procedure is useful for all kinds of foodstuff. (orig.) [Deutsch] Es wird ein Analysengang zur Abtrennung und Bestimmung von {sup 90}Sr, {sup 226}Ra, {sup 228}Ra und {sup 210}Pb in Lebensmitteln beschrieben. Ein Merkmal dieser Nuklide ist ihre hohe ...
Surface structure analysis, i.e. metallographic analysis of component surfaces with the aid of replicas, is an established method of component monitoring and the only reliable non-destructive method for detecting and analyzing beginning creep damage in the form of creep pores. Creep pore development provides a basis for component condition analysis. It must be noted, however, that the modern martensitic 9-12 % Cr steels - like the established steels 10CrMo9-10 (P22) und X20CrMoV12-1 - have comparatively high creep fracture deformation rates in fatigue tests. This raises the question if these steels can be judged on the basis of data for established steels. The results so far suggest that even with low pore densities (single pores), a higher degree of damage and a shorter time until failure must be assumed. [German] Eine bewaehrte Methode der Bauteilueberwachung stellt die Oberflaechengefuegeuntersuchung, d. h. die metallografische Untersuchung der Bauteiloberflaeche mit Hilfe von ...
This feasibility study of the uve Institut fuer Technische Chemie und Umweltschutz GmbH discusses the scientific and technical fundamentals of a catalytic process for complete removal of organic pollutants (PAH, H-HC, PCB, phenols, nitro-aromatics and organometallic compounds, e.g. from polluted soil and groundwater) by thermal-catalytic cracking and conversion into simple gases. The process is based on the catalytic reaction of the hydrocarbon compounds with water vapour in the temperature range of 700-900 degrees centigrade. The resulting gas mixtures consist mainly of hydrogen, carbon monoxide, carbon dioxide and methane which can be used as fuels, e.g. for heating or in gas engines. The process is an alterntive to combustion. It is therefore well suited whenever the pollutant to be removed is already mixed with water or water vapour and wherever in-situ removal would be too great a hazard. [Deutsch] Die vorliegende Machbarkeitsstudie aus dem uve Institut fuer Technische Chemie und ...
This contribution provides an overview and imparts basic knowledge on pertinent technical developments in magnetic resonance imaging (MRI) of the liver: 3D sequences, respiratory triggering, parallel imaging, and 3 Tesla (3T). 3D sequences can be used as T1-weighted (T1w) sequences for analyzing dynamics of contrast enhancement or as T2w sequences for MR cholangiography. Consistent improvements in respiratory triggering make it possible to obtain good image quality on T2w scans even in patients unable to hold their breath. Parallel imaging as a universal technique to accelerate image acquisition is particularly appropriate for MRI of the liver, and it has been shown that the reduced acquisition time is not achieved at the expense of image quality. Further progress in MRI of the liver can be expected with use of the 3T systems, but hitherto irrelevant problems must still be solved. Overall the innovations presented here, applied alone or in combination, facilitate rapid, robust, and ...
Tribological performance of alumina and silicon carbide ceramics as well as of the hardened steel 100Cr6 for reference was studied during reciprocating sliding and cavitation erosion in isooctane as substitute of gasoline and in distilled water. It was the aim to characterize effects of surface finish of the specimens and the liquid media on friction, resistance to sliding wear and cavitation erosion. Sliding wear tests were run on the self-mated ceramics and ceramic/steel pairs under conditions of boundary lubrication using a laboratory tribometer with cylinder-on-plate geometry. Vibratory cavitation erosion tests were conducted according to ASTM G 32-92. High initial surface roughness of coarse ground specimens led to a distinct running-in period during sliding contact with a transition from high to low values of friction coefficient and wear intensity. Incubation time was reduced with increasing surface roughness in the cavitation tests. Depending on the materials investigated, the ...
Purpose: An animal model is used to investigate whether MR angiography combined with super-paramagnetic particles of iron oxide (SPIO) is suitable for detecting thromboses. Methods: 42 rats in groups of 7 each were examined on days 1, 3, 5, 7, 9 and 11, respectively, after mechanical/chemical thrombus induction in a 1.5 Tesla magnet with a FISP sequence (TR/TE/FA 50 ms/6 ms/40 ). Imaging was performed before and up to 90 minutes after intravenous injection of 30 {mu}mol FE/kg BW of the experimental SPIO (hydrodynamic diameter, 34{+-}17 nm LLS; R1 and R2 relaxivity at 0.47 T, 31 and 57 L/(mmol*s)). MIP reconstructions of MR angiographies were submitted to consensus assessment by two examiners using histology as the gold standard. Results: The image quality of MIP reconstructions was rated as good in 38 of 42 cases. With regard to thrombotic vessel occlusion, MR angiography coincided with histology in 17 of 42 cases and differed in 25, lumen narrowing being overestimated by MRI in 4 ...
Aim: Treatment of carcinoma of the uterine cervix by remote afterloading brachytherapy has been accompanied with new isotopes having dose rates different from the classical low-dose rate (LDR) radium source. The dose rate conversion factor from LDR to high-dose rate (HDR) found to be around 0.54 in most studies. As regards medium-dose rate (MDR) brachytherapie, the published data are very few and the experience is still short. In this study the experience of Osaka University Hospital with micro-HDR-Selectron and Selectron-MDR, as a preliminary report of the clinical trial, is presented. Results: The 3-year survival and loco-regional control rates for both modalities were nearly equivalent (62% and 67% for HDR and 68% and 74% for MDR)(totally 45 patients). The cumulative rectal and bladder complication rates were the same in both groups (29% at 3 years), with only 1 patient (MDR-group) developed grade 3 rectal and bladder complication. In this study, point A dose rate correction factor ...
This thesis deals with the analysis of dominant loss mechanisms in direct methanol fuel cells (DMFC) and hydrogen fed polymer electrolyte membrane fuel cells (PEFC) by means of experimental characterization and modeling work. Due to different fuels used in these two fuel cell types, the dominant loss mechanisms are different in their nature. All in-situ characterization techniques that are used in this work are based on a novel test fuel cell with embedded reference electrodes. The first part of this work presents a new concept for realizing a reference electrode configuration in a polymer electrolyte membrane fuel cell by means of laser ablation. The laser beam is used to evaporate a small gap into the electrode surface of a catalyst coated membrane (CCM) to isolate the reference electrode from the working/counter electrode (WE/CE). This method enables the simultaneous ablation of the electrodes on both sides of the CCM because the membrane is transparent for the laser beam. ...
Objective: Optimization and testing of a high temperature combustion chamber for burning coal gas and conventional fuels natural gas or fuel oil. Coal gas is not available in such quantity for testing a full scaled combustion chamber. Therefore the design of the combustion chamber is based of experimental results from model tests and numerical solution procedures. Working program: (1) Analytical model for burning coal gas implemented in an existing computational fluid dynamics (CFD) code. (2) Three-dimensional calculations of a full scaled combustion chamber with a CFD code for flows accompanied by combustion and chemical reaction. (3) Improvement of measuring method for determination of flame temperature and concentration. (4) Temperature and concentration profil measuring in a full scaled combustion chamber by operating with natural gas or fuel oil. Results: An analytical model for burning coal gas was implemented in an existing two-dimensional CFD code. The model gave acceptable ...
When the use of retarders in utility vehicles increased in the middle of the 80s, the Forschungsvereinigung Automobiltechnik (FAT) commissioned a study on the safety aspect of this braking technology in trucks. Retarders are wear-free permanent brakes that are fitted in the drive transmission system of utility vehicles, thereby generating braking forces only at the wheels of the live shaft. The question of the possible overbraking of the live shafts was just as well investigated as the interaction between the retarder and service brake in so-called integrated braking systems, and both under conditions of low adhesion as well as in the border area of the dynamics of vehicle movement. This subject met with considerable joint interest on the part of the motor vehicle industry as well as of manufacturers of towed vehicles and unit sets. FAT, therefore, commissioned the Institut fuer Kraftfahrwesen of the University of Hannover to carry out a three-phase research project on the braking ...
A comparative process can be shown for the design of combined fuel cell powerstations. It is worth noting that the output of a combined powerstation working reversibly is independent of the thermodynamic state of the cell, and only depends on the reaction and thermodynamic state of the environment. The potential efficiency of gas-fired combined fuel cell powerstations is estimated at 80%. The fuel cell proves to be an isothermal heat source and not an adiabatic fluegas generator. This applies generally for all combustion power processes. Compared with external reforming, the integration of the reforming in the whole process leads to distinct advantages in efficiency if the possibilities of using the waste heat of intermediate thermal power processes are fully exploited. The plant implementation with an SOFC gas turbine process shows that realisation of a relatively simple plant concept leads to efficiencies distinctly above 70%. The enclosure design is of central improtance for the ...
When performing trenchless pipe renovation work - whichever process you use - the success of the job depends on the careful removal of all scale, sediments and rust from the innerwall surfaces. The VACUJET process - in which the pipe is cleaned with water at pressures of up to 2 500 bar using a technique jointly developed by Preussag Rohrsanierung GmbH and Fabex GmbH - meets all requirements. The equipment includes a mobile waste water treatment unit which is small enough to fit on a standard trailer. Despite its compact dimensions this plant is so effective that it can treat all the waste water generated during the high pressure cleaning jobs so that it is suitable for reuse in the cleaning process or for release into the sewerage system. (orig.) [Deutsch] Bei der grabenlosen Rohrsanierung, ganz gleich nach welchem Verfahren saniert wird, ist die sorgfaeltige Entfernung von alten Beschichtungen, Ablagerungen und Rost eine wesentliche Voraussetzung fuer den Sanierungserfolg. Das ...
The ERICAM model (Environmental Risk Internalization through Capital Markets) includes the capital markets as a source contributing to the coverage of risks due to nuclear activites, thus enhancing the effectiveness and functions of the nuclear liability law. The model proposed will allow higher amounts for compensation and will increase financial security, flow of information, and efficient use of resources. The implementation of the model can be achieved on the financing side by issuing Nuke bonds, linking accident-specific options to government bonds. This will essentially increase the risk coverage compared to present means, and will be a pin-pointed addition to the existing layer system. There are three institutions proposed to act as mediators in the implementation of the model: A government authority to supervise the trade in Nuke bonds. Risk-bearing associations in oder to enhance the model`s efficiency, and to reduce transaction costs. Rating agencies that will reduce the ...
Clinical information is indispensable for swift and cost-effective clarification of diseases of the larynx. While quality clarification of neurological changes in the area of the posterior cranial fossa and in the course of the vagus nerve as a cause of glottis malfunction is possible with MRI, localized disease of the larynx can more effectively be assessed with low-artifact CT. In the particularly difficult assessment of the post-operative larynx, a recurrence can be diagnosed only after a baseline study has been carried out after the end of therapy. With knowledge of the pretherapeutic findings, the findings immediately post-therapy, and the operation technique used, the optimal CT examination, which can be carried out quickly, will be able to provide more information about recurrence. (orig.) [Deutsch] Zur schnellen und kostenguenstigen Abklaerung von Erkrankungen des Larynx ist die klinische Information unabdingbar: Wenn neurologische Veraenderungen im Bereich ...
Recurrent variceal bleeding due to liver cirrhosis led to treatment with a transjugular intrahepatic portosystemic shunt (TIPS) in a pregnant woman at 20 weeks` gestation. Fetal radiation exposure was estimated to be less than 10 mSv. The use of a graduated catheter allowed measurement of field size and reliable determination of the patient`s entrance dose. Radiation exposure of an approximated fetal dosage of 5.2 mSv did not justify abortion for medical reasons. Therefore, TIPS procedure is not generally contraindicated during pregnancy itself. TIPS placement may be a therapeutic option related to the severity of the underlying maternal disease, after radiation exposure of the fetus has been estimated. (orig.) [Deutsch] Bei rezidivierender Oesophagusvarizenblutung auf dem Boden einer Leberzirrhose wurde bei bestehender Schwangerschaft der 20. Woche ein transjugulaerer portosystemischer Stent-Shunt (TIPS) neu angelegt. Praeinterventionell wurde die zu erwartende Strahlenexposition fuer ...
More than two and a half years of monitoring of a passive house school and day-care centre in Frankfurt a. M. show comfortable indoor climate and good air quality. The space heat consumption is low and shows savings of approximately 90 % as compared to average existing schools. Excellent performance was also achieved in terms of primary energy. The results of further analyses of the efficient ventilation system with heat recovery, the perimeter insulation as an alternative to floor slab insulation and the influence of the air change due to the entrance door are presented. (Abstract Copyright [2008], Wiley Periodicals, Inc.) [German] Ueber zweieinhalb Jahre Monitoring einer Passivhaus-Schule und Kindertagesstaette (KiTa) in Frankfurt a.M. zeigt behagliche raumklimatische Bedingungen bei guten Luftqualitaeten. Die Heizwaermeverbrauchswerte liegen wie erwartet niedrig und zeigen Einsparungen um 90 % gegenueber dem Durchschnitt im Bestand. Auch primaerenergetisch bewertet, weist die Schule ...
In an extended case report, we discuss four cases with masses in the lacrimal fossa representing the most important entities in this region (lymphoma, pleomorphadenoma, inflammatory pseudotumor, and malignant epithelial tumor). The different indications for CT and MRI are explained. For the differential diagnosis of lacrimal gland lesions, the following imaging parameters are important: The shape of the lacrimal gland, the inner structure, the degree of contrast enhancement, and the surrounding bony structures. In the evaluation of the expansion of lacrimal gland lesions, CT in thin slices with multiplanar reconstructions is equal to MRI. However, the contrast-enhancement of lacrimal glands is better evaluated with MRI than with CT. The bony structures are better visualized on CT than on MRI. (orig.) [Deutsch] In einem erweiterten Fallbericht wird ueber die vier grossen Entitaeten bei Traenendruesenraumforderungen berichtet (Lymphom, pleomorphes Adenom, entzuendlicher Pseudotumor und ...
Steam turbines of the new power plant generation enable the realisation of over-critical steam parameters with 600 C and 300 bar by means of simple and double resuperheating. Extensive research work in the field of material technology has provided the pre-conditions. Forged pieces, castings, high-temperature ferritic 9 - 10 % CrMoV steels, which are additionally alloyed with niobium, nitrogen and wolfram, are used in steam turbines. A proof of strength for shaft and cast steels is available by means of a long-term stress-rupture test of up to max. 60,000 hours. The strength of turbine steels exceeds the one in tube and header steels (x 10 CrMoVNbN 9 1). (orig./MM) [Deutsch] Dampfturbinen der neuen Kraftwerksgeneration erlauben heute die Realisierung von ueberkritischen Dampfparametern mit 600 C und 300 bar mit einfacher und zweifacher Zwischenueberhitzung. Umfangreiche werkstofftechnische Forschungsarbeiten haben dafuer die Voraussetzung geschaffen. Zur Anwendung ...
The low budgets of local governments and Federal States in Germany as well as lack of financial means of renters delaying thorough modernisation of existing heating systems in residential and public buildings, novel heat supply and related customer services are emerging on the market. Heat supply companies and housing construction associations increasingly use modern electronics and telecommunication systems for heating system upgrading and reliable operation and maintenance. This option holds an enormous potential of saving money today and in the future. Installation of remote control and maintenance systems and the related telephone-based services offer fast repair and other services via electronic telecommunications systems, thus saving money and manpower for the repair services of heat suppliers or plumbers, or financial losses due to rents being docked for broken down heating systems. Such remote control and maintenance systems however need to be reasonable in price, and versatile ...
The required introduction of on board diagnosis II in the USA from the 94 models onward has led vehicle manufacturers and system suppliers to develop corresponding diagnosis processes at the beginning of the 1990`s. These systems are now in mass production for TLEV and partly for LEV requirements. Based on experience from the wide use of these functions, new knowledge has been obtained, which must be taken into account in the development of future systems. The additionally more severe emission and diagnosis requirements make further minimisation of the overall tolerances on the one hand, and a revision of the existing diagnosis algorithms necessary. In parallel with this, the Law must create the necessary outline conditions, where the requirements for the vehicle manufacturer and system suppliers must also be met. The OBD II development must therefore certainly not be regarded as complete. [Deutsch] Die in den USA ab Modelljahr `94 geforderte Einfuehrung der On Board Diagnose II hat zu ...
The direct injection Diesel engine with its specific fuel consumption of about 200 g/kWh is one of the most efficient thermal engines. However in case of relatively low CH- und CO-emission the soot- and NO{sub x} concentration in the exhaust gas turns out to be a problem with respect to the legislation on emission limits. At the department of piston- and turbo-machines of the Trier University of Applied Sciences, a single-cylinder testing engine with two injection-systems (fuel and water) has been developed. This engine has been constructed to analyse the effect of stratified water-injection on the soot- and NO{sub x} emissions of exhaust gases of a Diesel engine. (orig.) [German] Der Dieselmotor mit Direkteinspritzung stellt mit spezifischen Kraftstoffverbraeuchen in der Groessenordnung von 200 g/kWh eine der wirtschaftlichsten thermischen Kraftmaschinen dar. Bei relativ niedrigen Kohlenwasserstoff- und Kohlenmonoxid-Emissionen erweist sich die Russ- und Stickoxid-Bildung jedoch ...
High-strength, fully hardening steels are used in general for applications involving severe wear and frequently also additional cyclic stress. For the latter condition, the available information and experimental data for component dimensioning are insufficient. Work reported in the dissertation therefore was intended to establish experimental information showing the performance of the bainitic roller bearing steel 100Cr6 and deducing rules of applicability to components, of the fatigue strength data obtained with the specimens. Various models for calculating the fatigue strength are presented together with their application to the steel 100Cr6. The results show that the weakest link model is a good concept for fatigue strength calculation, taking into account multiaxial loading. (orig/CB) [Deutsch] Hochfeste durchhaertende Staehle unterliegen in der Regel hohen Verschleissbeanspruchungen und werden darueber hinaus oftmals zusaetzlich schwingend beansprucht. Fuer die schwingende ...
Evaluation and interpretation of CT colonography is based on both 2D and 3D techniques. The 2D techniques are popular mainly because the time needed for evaluation is short. The 3D techniques allow better definition than the 2D techniques, especially of polyps close to folds or at the base of a fold. The evaluation strategies generally accepted so far (primarily 2D, with 3D for problem cases, or vice versa) demand knowledge of both 2D and 3D techniques. Newer 3D visualization techniques help make it possible to acquire more complete and faster recording particularly of areas that are not easily accessible to endoscopic examination. These user-friendly developments are thus well suited to improving the detection and the security of detection of polyps. It must be remembered that experience and the knowledge of associated artifacts and the limitations they can impose on diagnosis are prime requirements for the implementation of such visualization techniques. (orig.) [German] Die ...
This seminar dealt with the subject of indoor air pollution and welcomed participants from environmental consultancy agencies and authorities and institutions related with environmental protection. Leading scientists from research and authorities presented the current state of knowledge abut the risks of indoorair pollution. The papers contained in these proceedings addressed: room climate and sick-building syndrome; allergens in indoor spaces; pollutants emitted by exemplary building materials; pollutant levels of organic compounds in indoor spaces; air quality in motor vehicle interiors; indoor air pollution - risk assessment and need for actions. (Uhe) [Deutsch] Das Seminar zum Thema Innenraumluft wurde fuer TeilnehmerInnen von Umweltberatungsstellen und anderen mit Umwelt betrauten Behoerden und Institutionen veranstaltet. Fuehrende Wissenschaftlerinnen aus Forschung und Behoerden stellten den aktuellen Stand des Wissens ueber Risiken der Innenraumbelastung aus ihrer Sicht vor. Die ...
The staging of patients with multiple myeloma demands sensitive imaging methods for the assessment of the skeletal system. MRI allows for direct visualization of the bone marrow which exhibits five different infiltration patterns in multiple myeloma: 1. normal appearance of the bone marrow, 2. focal involvement, 3. homogeneous diffuse infiltration, 4. combined diffuse and focal infiltration, 5. ''salt and pepper'' pattern with inhomogeneous bone marrow signals due to multiple fat islands. The combination of T1w-SE and STIR sequences is best suited for detecting all infiltration patterns and for the differential diagnoses e. g. hemangiomas. With parallel imaging in MRI, acquisition times can be markedly reduced and whole-body screening of the bone marrow can be achieved within 30 min. MRI is superior to radiography for the detection of focal as well as diffuse infiltration. Multidetector computed tomography and especially 16- and 64-detector row ...
The oxidation of boron carbide in steam or air was recently extensively studied especially in Forschungszentrum Karlsruhe, Institut fuer Materialforschung. An important data set is available for the interaction modelling. An oxygen diffusion model through the superficial liquid boron oxide formed on the boron carbide external surface associated to a superficial reaction between the liquid boron oxide and steam is proposed to simulate the experimental kinetics from BOX rig and thermogravimetric tests on the interaction between steam and boron carbide at a temperature range 800 C to 1400 C. The oxygen diffusion model will be also useful to simulate interaction between boron carbide and Ar+O2 (air simulation) atmosphere when the steam pressure becomes zero. From the analysis of BOX rig experimental kinetics of non-condensable (H2, CO2, CO and CH4) gases we propose an oxygen diffusion model through the liquid boron oxide and a ''steam/liquid boron ...
Purpose: The determination of tumor volume in ocular tumors is very important for the planning and success of radiation therapy. This study uses an animal model to evaluate the accuracy of MR-based volumetry of ocular tumors. Materials and methods: In a total of 25 porcine eyes obtained from the slaughterhouse, ocular tumors were produced by injecting a mixture of hand creme and Gd-DTPA under ophthalmoscopic guidance. The injected volume varied between 0.05 ml and 2.7 ml. The eyes were examined with a 1.5 Tesla scanner and a 4 cm circular surface coil especially developed for ocular MRI. After data transfer to a separate workstation, volumetric analysis was carried out by three independent radiologists using semiautomated software. The determined volume was compared with the injected volume. Results: Of the 25 prepared porcine eyes, 23 were suitable for volumetric analysis. The injection of the mixture of hand creme and GD-DTPA produced two different types of tumors. ...
This assessment is a feasibility study according to ISO 14024. It deals with the question whether an ecolabel is suitable for wood pellet heating systems and how concrete criteria for an ecolabel for wood pellet heating plants could be specified. The study begins with a comprehensive market analysis in order to identify possible plants for which an ecolabel would make sense. In the main part of the study, the environmental relevance of the chosen plants is analysed. For this analysis, plant manufacturers were interviewed and a comparison between wood pellet heating systems and heating systems which use gas, oil or wood was carried out. On the basis of this analysis, it was possible to derive a number of criteria which were discussed with company representatives and other experts in this field. As a result of this dialogue and the investigation process as a whole, the introduction of an ecolabel for wood pellet heating plants can be recommended. Wood pellet heating systems are ...
Under the repository storage conditions of Eram and Konrad, waste packages designed for permanent storage must not contain or release freely mobile liquids, except for the minimum residues attainable by reasonable efforts or unavoidable. In accordance with a directive issued by the German Federal Ministry for the Environment (BMU), waste conditioning must be carried out so as to minimize waste volumes and, if possible, on the site where the waste arises. Liquid waste is conditioned most effectively by drying. At the present time, various different processes for drying liquid waste are employed as reflected by the state of the art: The Robe process; roller drying; the RDA process; Favorit; in-drum drying; and HPA liquid waste drying with make-up feed. The HPA process offers these advantages: Drying under atmospheric conditions, which means high level of dryness (freely mobile and releasable water is removed); the residual water content is 10%; isothermal drying by hot air, which ...
The role of high-resolution computed tomography (HRCT) and magnetic resonance imaging (MRI) in the diagnosis of preoperative and postoperative complications caused by acquired cholesteatomas will be described in this paper. The pre- and postoperative imaging of the temporal bone was performed with HRCT and MRI. HRCT and MRI were performed in the axial and coronal plane. MRI was done with T2 weighted and T1 weighted sequences both before and after the intravenous application of contrast material. All imaging findings were confirmed clinically or surgically. The preoperative cholesteatoma-caused complications depicted by HRCT included bony erosions of the ossicles, scutum, facial canal in the middle ear, tympanic walls including the tegmen tympani, and of the labyrinth. The preoperative cholesteatoma-caused complications depicted by MRI included signs indicative for labyrinthitis, and brain abscess. Postoperative HRCT depicted bony erosions caused by recurrent cholesteatoma, bony defects ...
The further optimisation and improvement of the efficiency of internal combustion engines require the realisation of new technologies leading to a distinctively faster warm-up behaviour of the coolant and lubricants as well as of the engine components after a cold start. In order to achieve reduced fuel consumption and exhaust gas emissions with the help of heat management, the design criteria of innovative cooling systems need to be reflected and adapted to future requirements. The use of intelligent components within the cooling system, such as the 'Stand Alone Rotary Valve' as a thermostat's substitute or the use of coolant pumps with a rotary valve integrated into the pump's inlet chamber, offer new ways to realise in a decisively quicker and more flexible way the appropriate heating up and cooling down procedures at varying driving conditions. A description of both of the intelligent components for the cooling system is given in this paper. The ...
Background. In multiple myeloma 5 different infiltration patterns can be differentiated: 1. Normal appearance of bone marrow, 2. focal involvement, 3. homogeneous diffuse infiltration, 4. combined diffuse and focal infiltration, 5. 'salt-and pepper' pattern with inhomogeneous bone marrow with interposition of fat islands. Methods. For the fast and total acquisition of all patterns a combination of a T1-weighted spin echo sequence and a fat suppression technique is superior. The focal involvement is clearly demonstrated as areas of high signal intensity on e.g. STIR images. Diffuse involvement can be quantified objectively by calculation of the percentage of signal intensity increase after contrast material injection. MRI is superior to X-ray in focal and diffuse involvement. With ultrafast sequences a 'screening' of the whole red bone marrow as for myeloma infiltration is possible. Prognosis. In prognosis studies diffuse infiltration is inferior to ...
Introduction: The goal of this study was to compare contrast-enhanced T1-weighted Flash and Turbo-Flash sequences with conventional spin-echo sequences as a basis for planning high-precision radiotherapy. Methods: A total of 25 consecutive patients with different intracranial tumors and a disrupted blood-brain barrier were studied. T1-weighted Flash, Turbo-Flash and conventional spin-echo images were evaluated after controlled 30-s infusion of 0.1 mmol/kg body weight of Gd-DTPA. The evaluation of the three sequences included the measurement of the signal- and contrast-to-noise ratios, the visual inspection of the tumors and artifacts, and the measurement of tumor size. Results: The signal- and contrast-to-noise ratios were significantly (P<0.05-0.01) lower for Flash and Turbo-Flash than for conventional spin-echo sequences. However, visual inspection of the contrast-enhancing tumors revealed in 23 and 24 of 25 lesions of Flash and Turbo-Flash images, respectively, good or very good ...
The dispersion curves E(k-bar) have been calculated for bound and resonant (110) surface states of AlSb, AlAs, and AlP. AlSb is predicted to have no surface states within the bulk fundamental band gap, but AlAs and AlP are predicted to have surface state band minima which are very near the conduction band edge, and could lie either within the gap or immediately above the edge.
This research project aimed to determine the factors for the transfer of the elements silver (Ag), cerium (Ce), cobalt (Co), chrome (Cr), gallium (Ga), lanthanum (La), molybdenum (Mo), niobium (Nb), radium (Ra), ruthenium (Ru), antimony (sb), thorium (Th), titanium (Ti) and uranium (U) from food into the mother's milk. This factors will be used as a basic to check and derive activity values for the contamination of food and for radiation protection at working places of suckling women. For this purpose 19 mothers collected samples daily (2-8 weeks), using the duplicate method, of all the food they consumed as well as of their milk. After microwave-assisted digestion the element contents were analysed by mass-spectroscopy with inductive coupled plasma (ICP-MS). The results of the mothers who participate for more than 5 weeks were used to make a time lapse between the intake and transfer of the elements in the mothers milk visible. (orig.) [German] Ziel dieses Forschungsvorhabens ...
Purpose: In an experimental study, the correlation between the trabecular bone density of the different regions of the proximal femur and the fracture load in the setting of femoral neck fractures was examined. Methods: The bone mineral density 41 random proximal human femora was estimated by single-energy quanitative CT (SE-QCT). The trabecular bone density was measured at the greatest possible extracortical volume at midcapital, midneck and intertrochanteric level and in the 1 cm{sup 3} volumes of the centres of these regions in a standardised 10 mm thick slice in the middle of the femoral neck axis (in mg/ml Ca-hydroxyl apatite). The proximal femora were then isolated and mounted on a compression/bending device under two-legged stand conditions and loaded up to the point when a femoral neck fracture occurred. Results: Statistical analysis revealed a linear correlation between the trabecular bone density and the fracture load for the greater regions, with the highest value in the ...
Court decisions available so far do not primarily consider the problems linked to the commissioning of an expert and his mandate, as well as the legal status of the commissioning of an expert as an administrative act which might be legally contestable. Thus there are at present no court decisions that would create legal certainty in matters of the act of commissioning a nuclear expert opinion. The current legal situation is such that an independent order for commissioning of an expert opinion in compliance with section 19 III AtG (Atomic Energy Act), which in general is given in response to the refusal of the facility operator to do so, can be independently contested on the basis of section 44 a, sentence 2 VwGO (Rules of Administrative Courts). The current practice of conflict-oriented, or nuclear power phase-out-oriented, implementation of the nuclear law poses a threat to our constitutional state and to our democracy. The supply of energy as a common good is of essential importance ...
In comparison to deterministic criteria, probabilistic reliability indices like interruption frequency and unavailability give a more differentiated insight into reliability in an electrical energy network. One possibility for network planning based on these indices is the definition of limits for customer nodes, another is the monetarisation of reliability in terms of interruption costs. Because of numerous disadvantages, interruption cost methods could not up to now win broad recognition in network planning in Western Europe. A more recent method for the monetarisation of reliability circumventing most of these disadvantages is the insurance system. In this system the customer selects a tariff class in an insurance system, and the utility reimburses its customers in the case of an interruption. In its first section, the paper describes a method for the flexible and realistic optimisation of MV networks. This method based on Genetic optimisation is able to integrate probabilistic ...
The transversus perinei profundus muscle is a well known structure in found anatomical textbook. Fibres of this muscle are believed to form the so-called external urethral sphincter (musculus sphincter urethrae). Recently histomorphologic investigations have shown that there is no muscular connection between the musculus sphincter urethrae (external sphincter) and the muscle system of the pelvic floor. Furthermore, the external sphincter was found to be divided into parts: The transversely striated part (musculus sphincter urethrae transversostriatus) and the smooth part (musculus sphincter urethrae glaber). Similar to histomorphologic investigations, contrast-enhanced MR imaging has shown the musculus sphincter urethrae to be surrounded by fatty and connective tissue only. Neither in MRI nor in anatomical slices can any connection between the urethral sphincter and the muscle system of the pelvic floor be found. Thus, on the basis of the results presented in this work it is concluded ...
Purpose: Budd-Chiari syndrome is a fairly uncommon disease in Europe. This often leads to its late diagnosis. The syndrome is characterised by portal hypertension and splanchnic congestion due to obstruction of hepatic venous outflow. This paper describes the treatment of three patients with Budd-Chiari syndrome by interventional therapeutic techniques and discusses alternative treatment modalities. Patients and Methods: The first patient presented with veno-occlusive disease and was treated by the placement of a transjugular intrahepatic portosystemic stentshunt. The second patient showed an occlusion of the major hepatic veins. After percutaneous recanalisation, a stent was placed in the right hepatic vein which remained patent. The third patient had a membranous obstruction of the right hepatic vein which was treated by percutaneous balloon dilatation. Results: In all patients the clinical symptoms resolved completely after treatment and no complications were encountered. ...
The measuring series was performed from November 1991 through April 1992 in seven drinking-water conditioning plants of the Fichtel mountains area in the north-eastern part of Bavaria, and the results revealed as an annual average a dose of about 1 - 40 WLM. The area of interest is a drinking-water catchment area where the ground water and other water resources include waters particularly rich in radon content, which explains this relatively high dose range. This is why comprehensive, specific local and long-term mearurements were carried out in order to assess the occupational radiation dose in the drinking-water conditioning plants, taking as a model site the conditioning plant of the municipal utilities of Hof in Weissenstadt. These more specific measurements were performed by the Technical Inspectorates (TUeV) of Bavaria and Saxony and the isotope laboratory of Georg-August University of Goettingen in mid-April 1994 (Goettingen University, TUeV Saxonia and Bavaria) and from June ...
The properties of AlN make this material very attractive for optical, electronic, and tribological application. Also, if the AlN could be formed on the Al surface to enhance its surface properties, Al could be applied for the lightening of machine parts. However, a dense oxide film exists on the surface of Al, which prevents the formation of the Al nitride even during plasma nitriding and plasma coating process. In this study, plasma nitriding has been tried to form an AlN layer on Al after the surface activation processes. During the plasma nitriding, the density of the nitrogen ions was amplified by means of controlling the power of the Al substrates. The film thickness, microstructural features and the mechanical properties such as hardness and wear properties of the AlN layer ...
Purpose: To report on the nephron-sparing, percutaneous ablation of a large renal cell carcinoma by combined superselective embolization and percutaneous radiofrequency ablation. Materials and Methods: A 5 cm renal cell carcinoma of a 43-year-old drug abusing male with serologically proven HIV, hepatitis B and C infection, who refused surgery, was superselectively embolized using microspheres (size: 500 - 700 {mu}m) and a platinum coil under local anesthesia. Percutaneous radiofrequency ablation using a 7F LeVeen probe (size of expanded probe tip: 40 mm) and a 200 Watt generator was performed one day after transcatheter embolization under general anesthesia. Results: The combined treatment resulted in complete destruction of the tumor without relevant damage of the surrounding healthy renal tissue. The patient was discharged 24 hours after RF ablation. No complications like urinary leaks or fistulas were observed and follow up CT one day and 4 weeks after the radiofrequency ...
Aim: Changes within the brain detected by MRI after chronic manganese poisoning raised the question whether morphological changes of the basal ganglia, particularly of the globus pallidus, could be detected after chronic occupational exposure to manganese dioxide. Results: No cases of parkinsonism were detected in clinical examinations or by other means. The mean manganese concentration in blood was 12 {mu}g/l (range: 3.9-23.3 {mu}g/l). In comparison to the upper reference value of 10 {mu}g/l, 42 workers (56%) had a higher body burden. A significant positive correlation between manganese levels in blood and the PI (indicated by T{sub 1}-shortening) was observed as well as between the CBI and workplace-specific exposure. Brain atrophy was not detected in any of the observed cases. Conclusions: Long-term exposure to manganese dioxide dust correlates with the Pallidum-Index in MRI scans. Although the MRI findings have no current clinical relevance for individuals, further studies are ...
To evaluate the usefulness of radiation therapy alternative to surgery for clinical N0-N1 non-small cell lung cancer (NSCLC). From 1976 through 1989, 116 patients with NSCLC without mediastinal involvement were treated with definitive radiation therapy alone at Gunma University Hospital. All patients were treated with once-daily standard fractionation using 10 MV X-rays. The total dose ranged from 60 Gy to 80 Gy. The actuarial 2- and 5-year survival rates of the entire group were 43% and 20%, respectively with a median survival time of 19 months. The survival of 76 patients with stage T2 tumors was significantly better than that of 28 patients with T3 tumors (mean survival time 21 versus 15.5 months; p<0.05). Sixty-two patients with tumors less than 5 cm in diameter had a 2-year progression rate of 20%, in comparison with 39% of 54 patients with tumors greater than 5 cm. The difference of survivals for these 2 groups was statistically significant. Twelve patients given a total dose ...
We present a study of the crystal field in PrNiAl, NdNiAl, ErNiAl and ErCuAl intermetallic compounds based on inelastic neutron spectroscopy. These compounds crystallize in the ZrNiAl-type hexagonal structure with an orthorhombic symmetry on rare-earth sites. The results are compared with the specific-heat data, and the lower parts of the crystal-field energy-level schemes are determined. (orig.)
We present a study of the crystal field in PrNiAl, NdNiAl, ErNiAl and ErCuAl intermetallic compounds based on inelastic neutron spectroscopy. These compounds crystallize in the ZrNiAl-type hexagonal structure with an orthorhombic symmetry on rare-earth sites. The results are compared with the specific-heat data, and the lower parts of the crystal-field energy-level schemes are determined. (orig.)
The obligations under international law to reduce transfrontier air pollution is discussed in five chapters from various aspects. Consequences for the European Communities are gone into in five further chapters. (orig./HP)
The microelectronic cable diagnosis is a substantial tool to determine destruction free the residual strength and the lifetime of laid PE/XLPE medium voltage cables. Fundamentals of the ageing diagnosis and a cost reduced inspection concept are the `Isothermal-Relaxation-Current` Analysis and the Neuro-Fuzzy evaluation software. These new tools are able to determine the ageing status of the investigated cable without any references. The authors also show that the test breakdown during the assessment of the ageing status of criterial systems can be reduced by this approach. The cable diagnosis equipment KDA is also useful for the steering of investment as well as for preventive maintenance. (orig.) [Deutsch] Die zerstoerungsfreie dielektrische Kabeldiagnostik kann heute einen wesentlichen Beitrag zur Bestimmung der Restfestigkeit und der Restlebensdauer eines PE/VPE-isolierten Mittelspannungskabels leisten. Basis der Alterungsdiagnose und des Konzeptes ...
This article describes the processes for the treatment of plastic waste: sampling, sorting, comminution. The requirements for the different processes for waste treatment (as recycling, utilization as raw material, energy recovery, combustion) are listed. (SR)
The report provides and overview of calculation models for the simulation of airflows and deals comprehensively with field and multi-zone models as well as the coupling of individual zone and multi-zone models. Examples of calculations are given. figs., tabs., refs.
Fundamental investigations into the biosorption of environmentally relevant heavy metals were carried out with different microbial adsorbents, and processes were proposed for industrial effluents. In order to improve the technology of biosorption processes, attempts were made to improve the sorption efficiency of biological sorbents, and investigations were carried out on the immobilisation of biological adsorbents. (orig.) [Deutsch] Es wurden Grundlagenuntersuchungen zur Biosorption von umweltrelevanten Schwermetallen mit verschiedenen mikrobiellen Adsorbentien durchgefuehrt und an technischen Abwaessern Technologievorschlaege erarbeitet. Zur Verbesserung der Technologie von Biosorptionsprozessen wurden Moeglichkeiten der Steigerung der Sorptionsleistung von Biosorbentien erarbeitet und Untersuchungen zur Immobilisierung der biologischen Adsorbentien durchgefuehrt. (orig.)
In order to remove ash from coal, it is introduced into an aqueous ash removal solution, which contains nitric acid or citric acid and ammonium hydrogen fluoride. The coal without ash is then separated from the aqueous solution. According to the process, either finely ground coal is introduced into the ash removel solution or the coal with the solution is ground in a wet pulveriser.
"2"7Al and "2"9Si solid-state NMR spectra and X-ray diffraction (XRD) patterns were obtained for #alpha#-SiAlON powders prepared by combustion synthesis, according to which the phase transformation and structure evolution of #alpha#-SiAlON were studied. It was found that in #alpha#-SiAlON "2"9Si chemical shift values (-48 < #delta# _S_i < -47) were close to those in #beta#-Si_3N_4 and #alpha#-Si_3N_4, indicating that Si atoms kept SiN_4 coordination to a large extent in #alpha#-SiAlON despite the presence of O atoms. Dissimilarly, "2"7Al chemical shift values in #alpha#-SiAlON deviated clearly from that corresponding to AlN_4 coordination (#delta# _A_l #approx# 112) and occurred in a range from #delta# _A_l 95.5 to 99.9, which should be assigned to tetrahedral ...
Conduction properties of Rb"+ ion in Rb-Al-priderite and K"+ ion and Rb"+ ion in (K,Rb)-Al-priderite, were investigated by NMR using "2"7Al in the framework as a probe. Size effect was observed remarkably in the activation energies. Frequency dependence of T_1 in Rb-Al-priderite at a low temperature indicates that the relaxation behavior of "2"7Al in Rb-Al-priderite can be described by the continuum model. Barrier height distributions and 'attempt frequencies' in both samples obtained by a curve-fitting method are discussed in comparison with those of K-Al-priderite. (orig.).
Synthesis of Eu-doped #beta#- and 15R-SiAlONs was studied by the ammonia nitridation of precursors derived from an #alpha#-Si_3N_4 fine powder dispersed in aluminum glycine gel with various Si/Al ratio and post-annealing in a nitrogen pressure furnace. The largest amount of #beta#-SiAlON was observed in the product at 1750 deg. C for Si/Al = 1/1 with small amounts of both #alpha#- and 15R-SiAlON impurities. The product showed two emissions at around 420 nm and 560 nm. The emission intensities decreased with increasing amount of #beta#-SiAlON. The former and latter emissions were assigned to Eu"2"+ in the 15R- and #alpha#-SiAlONs impurities. A mixture of Eu-doped 15R-SiAlON with #alpha#-Al_2O_3 impurity was obtained for Si/Al = 1/6, using AlN together with ...
Objective: To determine the reproductibility of three-dimensional volume and thickness measurements of the knee joint cartilage with MRI in volunteers. Methods: The knees of 7 healthy individuals (ages 23 to 58 yrs.) were sagitally imaged with a resolution of 2x0.31x0.31 mm{sup 3}, using a fat-suppressed FLASH-3 D sequence. The knee was repositioned in between replicate acquisitions, 6 data sets being obtained in each case. After semiautomatic segmentation and three-dimensional reconstruction of the cartilage, the thickness was determined independent of the original section orientation. The coefficient of variation for repeated volume measurements and the deviations of the maximal cartilage thickness values were calculated subsequently. Results: The mean variation of the cartilage volumes of the replicate measurements was 1.4% ({+-}0.8%) in the patella, 1.7% ({+-}1.5%) in the femur, 3.0% ({+-}1.2%) in the medial tibial plateau and 3.5% ({+-}2.0%) in the lateral tibial plateau. The ...
The experimental effect investigation programme on Zircaloy-4/air oxidation was pursued and expanded to isothermal specimen exposure and the comparison of the oxidation between the atmospheres Ar/O{sub 2} and air. In close connection with the EC project OPSA, which is meanwhile terminated, the investigation concerned specimen exposure in a thermobalance to flowing atmospheres, namely dry Ar/O{sub 2} of composition 80/20 or synthetic air, respectively. As test parameters the linear heat-up rate was varied in the range 5 to 40 K/min and the ramp or holding temperature between 800 and 1500 C. Mass increase and reaction rate were continuously recorded or evaluated in temperature/time dependence. The oxide scale growth was found to be accompanied by colour changes, crack formation and spalling of layers, as well as by dimensional substrate growth, which are the reasons for the observed kinetic results. The microstructural investigation confirms nitrogen to be essentially responsible for the ...
Poly-Lactic-Acid (PLA) was evaluated for coating of vascular endoprotheses in the treatment of experimental arterio-venous-fistulae (AVF). Bilateral carotid-external jugular AVF were created in 5 adult dogs. 7 PLA coated nitinol stents were placed via a transfemoral approach covering 5 AVF. The contralateral AVF remained untreated. Angiography was performed immediately after stent placement, at weeks 1 and 3 and at months 3, 6 and 9. All grafts were removed and underwent histologic examination. In 2 cases the occlusion of the AVF was successful, while misplacement occurred in 3 cases. Occlusion of the parent vessel was disclosed in 3 cases. Histologic examination revealed a mild inflammatory reaction with the presence of macrophages. There was no foreign-body reaction or fragmentation of the arterial vessel wall. PLA, which is a well-known biodegradable material, showed a good mid-term biocompatibility. Elastic mismatch of the non-elastic coating and the self-expandable nitinol stent ...
The fundamental recommendations of the ICRP issued in its publication of 1990 stipulate the general principle of performance of dose measurements at regular intervals in the field of diagnostic radiology, for the purpose of equipment performance checking and optimization of radiological protection. In response to this requirement, the Federal Ministry, in cooperation with experts and the competent supervising authorities, has issued an order to install dose-area-product meters in angiographic examination systems, imaging systems and fluoroscopic screen devices primarily used for examining infants and children up to the age of 12. This is done in response to reported cases of adverse effects of radiation exposure and the high priority given to radiological protection in the examination of infants and children. In 1992, an expert group was convened to discuss and elaborate instructions for including dose-area product measurement in the dosimetry activities in medical diagnostic ...
Functional imaging of the pharynx used to be the domain of cineradiography, CT and ultrafast CT. The development of modern MRI techniques led to new access to functional disorders of the pharynx. The aim of this study was to implement a new MRI technique to examine oropharyngeal obstructive mechanisms in patients with obstructive sleep apnea (OSA). Sixteen patients suffering from OSA and 6 healthy volunteers were examined on a 1.5 T whole-body imager (`Vision`, Siemens, Erlangen Medical Engineering, Germany) using a circular polarized head coil. Imaging was performed with 2D flash sequences in midsagittal and axial planes. Patients and volunteers were asked to breathe normally through the nose and to simulate snoring and the Mueller maneuver during magnetic resonance imaging (MRI). Prior to MRI, all patients underwent an ear, nose and throat (ENT) examination, functional fiberoptic nasopharyngoscopy and polysomnography. A temporal resolution of 6 images/s and an in-plane resolution of ...
SiC-AlN and SiC-SiAlON refractory composites were obtained by means of nitridation of the mixtures of silicon carbide (SiC) powder with a broad granulometric distribution and powders of aluminium (Al) and aluminium-silicon (Al-Si) mixtures. The mixtures of the composition Al-25% Si, Al-50% Si and Al-75% Si were previously prepared by means of 'mechanical alloying' technique. Thermodynamic analysis was accomplished in order to evaluate the viability of SiC-SiAlON and SiC-AlN refractories production by the chosen processing method, and the results confirmed viability of such. Investigation of nitridation of Al and Al-Si powder compacts in order to obtain the AlN and #beta#-SiAlON matrix phases of the composite was ...
XAFS data of metallic glass Al_0_._9_1La_0_._0_9 and a crystalline phase Al_1_1La_3 formed by annealing of the glass were measured at the La L_3 edge at T=12 K and analyzed using the radial distribution function method. The shortest La-Al distance appeared to be distinctively smaller within the glass than in the crystal. This difference decreases the disparity in size of La and Al in the alloy, allowing their mixing in the glassy state. ((orig.)).
Purpose: Measurement of the oscillating CSF flow in the spinal canal (SC) of healthy volunteers and in patients with post-traumatic syringomyelia (PTS) using an optimized MRI protocol as well as to determine whether stenosis induced velocity changes are detectable using MRI. Methods: In 68 healthy volunteers quantitative studies of CSF flow in the cervical, thoracic, and lumbar regions were performed. First, an optimized sequence was developed and tested in 19 volunteers using four different flow-encoding velocities (4, 8, 12, 16 cm/s). Secondly, the optimized sequence was employed in 49 volunteers to measure the different CSF patterns in the cervical, thoracic, and lumbar spinal canals (CSC, TSC, LSC). Part three of the study, in which patients with PTS are being examined is still underway. We measured the maximum velocity (cm/s), the pixel area (mm{sup 2}), and the stroke volume (ml/s). Using a flow model the velocities prior to and after compression with 5 different power levels ...
The morphology and size characteristics of the population of AlP particles produced by treatment of a pure aluminium melt with an Al-Fe-P inoculant addition have been determined. The particles are shown to be polyhedral like the primary silicon they nucleate in hypereutectic Al-Si alloy melts and to be prone to clustering at increased phosphorus addition levels. The number of AlP particles per unit area is shown to be comparable with the corresponding number density of polyhedral primary silicon in Al-20 wt.% Si treated in the same way under identical conditions which is consistent with earlier conclusions that AlP acts as a nucleation catalyst for primary silicon in hypereutectic Al-Si casting alloys. (orig.)
... In a HEAO 1 study of active galaxies, principally Seyfert 1s, in the 2, 165 keV energy range, Rothschild et al. ... As discussed by Rothschild et al. ...
Phase transformations from #alpha#- to #beta#-SiAlONs (i.e., from #alpha#' to #beta#') have been recently reported in a number of rare-earth SiAlON systems during postsintering heat treatment. In the present work, this transformation process in a Sm (#alpha# + #beta#)-SiAlON material is studied by using XRD, TEM, and EDS X-ray mapping techniques. It is observed that in addition to the formation of #beta#' and M' phases, the #alpha#'-to-#beta#' transformation is accompanied by a significant increase in the amount of an AlN-polytypoid phase. The results suggest that some #alpha#' phases are thermodynamically unstable at temperatures lower than the material sintering temperature and will decompose when conditions allow. For the composition studied in this work, the #alpha#-SiAlON decomposition can be described in general as #alpha#' #-># #beta#' + M' + AlN ...
Effect of Al and AlP particles on the microstructure of near eutectic Mn-Si alloy (Mn-30 wt.%Si) was studied by Electron Probe Micro-analyzer (EPMA) and Differential Scanning Calorimeter (DSC). Crystal lattice correspondence analyses show that both Al and AlP have good lattice matching coherence relationships with MnSi phase, and the addition of Al and AlP particles results in an abnormal eutectic structure, i.e. the eutectic constitution MnSi and Mn{sub 5}Si{sub 3} precipitate separately: MnSi precipitates firstly, and then the Mn{sub 5}Si{sub 3} phase.
Lea, MN Micro Albertville, AL Micro Albuquerque, NM Metro Alexander City, AL Micro Alexandria, LA Metro Alexandria, MN Micro Alice, TX Micro Allegan, MI Micro...
Abstract Electronic structures of two representative zigzag and armchair models of aluminum phosphide nanotube (AlPNT) were investigated by density functional theory calculations. The structures were optimized and the bond lengths, tip diameters, band gaps, and dipole moments were calculated. Moreover, the quadrupole coupling constants (CQ) were calculated for the Al-27 atoms of the optimized structures. The same values of AlP bond lengths were calculated for both models. The larger value of band gap of armchair model than the zigzag model indicated the stronger dielectric property for the former model. The values of CQ(27Al) were the largest for the Al atoms placed at the tips of both zigzag and armchair AlPNT than other Al atoms, which could reveal dominant role of the Al atoms placed at...
The position paper will provide the basis for further strategies on offshore wind power development in consideration of ecological and conservation aspects. [German] Das Positionspapier des Bundesministeriums fuer Umwelt, Naturschutz und Reaktorsicherheit (BMU) einschliesslich des Umweltbundesamtes (UBA) und des Bundesamtes fuer Naturschutz (BfN) ist Ergebnis der Arbeiten der BMU-Projektgruppe 'Windenergienutzung im Offshore-Bereich im Hinblick auf die BMU-Anliegen'. Es beschreibt den derzeitigen Stand einer Strategie zur umwelt- und naturvertraeglichen Erschliessung der Windenergienutzung auf See (Offshore). Es bildet die Grundlage fuer die Weiterentwicklung dieser Strategie und dabei insbesondere zur Abstimmung mit den Anliegen anderer Bundesressorts und den Kuestenlaendern, sowie zur intensiveren Einbeziehung beteiligter Verbaende und Fachkreise. Vor dem Hintergrund der zur ...
Our work deals with accumulative roll bonding (ARB) of pure Mg sheet (0.9mm thickness) and of Al5052 sheet (0.5mm). A stacking of Al-Mg-Al was firstly rolled to 50% reduction at 400"0C and secondly ARB has been processed up to 3 cycles. In such multilayers as well as highly mixed composites of two-phased system texture development, phase reactions and strain accumulation are of basic interest, which needs a combination of different experimental methods for characterization. The present paper deals with the global texture evolution measured by thermal neutrons to average always over the whole sample thickness, SEM and optical microscopy indicates the macroscopic development of Mg and Al layers. The initial materials show typical and strong basal plane texture of hexagonal Mg (17.9mrd) and a recrystallization texture of cubic Al (8.5mrd). Co-deformation of Al/Mg/Al leads to strong ...
#beta#-SiAlON was synthesized from a zeolite by NH_3 gas nitridation and its formation mechanism was investigated using X-ray diffraction and "2"9Si and "2"7Al NMR spectroscopy. It was revealed that most of the Si and Al atoms react to form #beta#-SiAlON via amorphous forms of Si-Al-O-N and O-SiAlON. Nitridation using NH_3 gas is an effective means of preventing mullite formation and promoting the introduction of nitrogen into aluminosilicate materials at lower temperatures than temperatures required by the carbothermal reduction nitridation process. Further, the NMR spectra showed that the siliceous part of the system changed into low z-value of Si_6_-_zAl_zO_zN_8_-_z (#beta#-SiAlON) and the incorporation of Al components into the #beta#-SiAlON was promoted in the later stages ...
Purpose: For planning the therapeutic strategies and estimating the prognosis in esophageal cancer, N-staging is very important. To date, MRI still is of minor importance as imaging modality of the mediastinum despite promising developments in the past, like ECG-gating or 'averaging' sequences, e.g. LOTA (Long-term averaging), which facilitate mediastinal and thoracic MR-imaging. In a prospective approach, the value of MRI based N-staging was examined with respect to LOTA-sequences. Material and Methods: Within from weeks prior to esophagectomy, standardized MRI of the esophagus was performed in 15 patients (10 squamous-cell-carcinomas and 5 adenocarcinomas) using a 1.5 T whole body scanner. Imaging quality was classified based on depiction of aortic wall or tracheal wall layers. Criteria for malignant infiltration were a diameter of more than 15 mm or a round appearance of a lymph node together with GD-DTPA enhancement. All data were blinded and separately read by ...
Tumours lesions of the temporal bone and of the cerebello-pontine angle are rare.This tumours can be separated into benign and malignant lesions. In this paper the CT and MRI characteristica of tumours of the temporal bone and the cerebello-pontane angle will be demonstrated. High resolution CT (HRCT) as usually performed in the axial plane are using a high resolution bone window level setting, coronal planes are the reconstructed from the axial data set or will be obtained directly. With the MRI FLAIR sequence in the axial plane the whole brain will be scanned either to depict or exclude a tumour invasion into the brain. After this,T2-weighted fast spin echo sequences or fatsuppressed inversion recovery sequences in high resolution technique in the axial plane will be obtained from the temporal bone and axial T1-weighted spinecho sequences before and after the intravenous application of contrast material will be obtained of this region. Finally T1-weighted spinecho sequences in high ...
The programme 'Solarthermie 2000' aimed at the testing and optimization of active solar systems, especially for service water heating. Sub-programme 2 was to provide the technical fundamentals and achieve a certain degree of standardization in order to make the technology economically competitive. This necessitated long-term monitoring of a representative number of systems. [German] Im Rahmen des Foerder- und Demonstrationsprogramms Solarthermie 2000, Teilprogramm 2 erfolgt durch die Foerderung von bis zu 100 solarthermischer Anlagen mit Schwerpunkt in den neuen Bundeslaendern eine umfassende Erprobung und Optimierung von Systemen zur aktiven thermischen Sonnenenergienutzung vorwiegend zur Brauchwassererwaermung. Mit dem Teilprogramm 2 sollen die technischen Voraussetzungen fuer einen kuenftigen wirksamen Beitrag der Solarthermie zur Energieversorgung geschaffen und durch Systemstandardisierung die ...
Meltdown and gasification of waste in an oxygen atmosphere ('2sv' process) is an economically efficient alternative to energetic and thermal utilisation of biomass. Organic pollutants are split at temperatures up to 2000 C in a reducing atmosphere. The process uses elements of the oxygen cupola furnace for melting and gasification of many different waste fractions, e.g. polluted waste wood, household refuse and bulk waste, old tyres, light shredder fractions, sewage sludge, etc. [German] Die Sauerstoff-Schmelz-Vergasung ('2sv') stellt eine wirtschaftliche Alternative zur energetischen Nutzung von Biomassen wie auch zur thermischen Abfallverwertung dar. Organische Schadstoffe werden bei diesem neuen Verfahren bei Temperaturen bis zu 2000 C unter reduzierenden Bedingungen aufgespalten. Das Verfahren nutzt Elemente des Sauerstoff-Kupolofens fuer die Schmelzvergasung und eignet sich fuer zahlreiche Abfallarten ...
In the first part of this contribution, the definition of reference values is given and the theoretical and practical problems in the application of this concept are discussed. In this connection, the present resources on instrumentation and the technical requirements for dose assessment are described. In the second part, some consequences are taken and proposals for further actions are made. (orig.) [German] Im ersten Teil des Aufsatzes werden Definitionen von Referenzwerten in der radiologischen Diagnostik untersucht und die theoretischen und praktischen Probleme der Umsetzung des gesamten Konzepts eroertert. In diesem Zusammenhang werden auch der gegenwaertige Geraetebestand und die technischen Voraussetzungen zur Dosisermittlung beschrieben. Im zweiten Teil werden daraus Schlussfolgerungen gezogen und Vorschlaege zum weiteren Vorgehen gemacht. (orig.)
In the first part of this contribution, the definition of reference values is given and the theoretical and practical problems in the application of this concept are discussed. In this connection, the present resources on instrumentation and the technical requirements for dose assessment are described. In the second part, some consequences are taken and proposals for further actions are made. (orig.) [German] Im ersten Teil des Aufsatzes werden die Definition von Referenzwerten in der radiologischen Diagnostik untersucht und die theoretischen und praktischen Probleme der Umsetzung des gesamten Konzepts eroertert. In diesem Zusammenhang werden auch der gegenwaertige Geraetebestand und die technischen Voraussetzungen zur Dosisermittlung beschrieben. Im zweiten Teil werden daraus Schlussfolgerungen gezogen und Vorschlaege zum weiteren Vorgehen gemacht. (orig.)
This is a process for the manufacture of a filter material for cleaning industrial or internal combustion engine exhaust gases and filter material manufactured according to the process. The filter material is manufactured from the mineralized combustion product of peel of tropical fruits burnt at a temperature of 820/sup 0/C to 840/sup 0/C in an oxidising atmosphere excluding the production of carbon, particularly using banana skins and orange peels, which product is granulated with carrier materials or compressed.
A programme to optimize the short-term operation planning of hydrothermal system scheduling is presented. Based on heuristics, an operational planning of pumped storage plants and a method for fast evaluations of spot market deals under consideration of load forecast errors was developed. (orig.) [German] Vorgestellt wird ein Programm, das - basierend auf Heuristiken - den kurzfristigen Einsatz eines hydrothermischen Kraftwerksparks optimiert. Im Programm wurde dazu ein Verfahren zur Pumpseichereinsatzplanung und zur sekundenschnellen Bewertung von Spot-Markt-Geschaeften unter Beruecksichtigung von Lastprognosefehlern entwickelt. (orig.)
This publication contains the Ordinance on Heating Costs, the Ordinance on Heating Installations, and the 1st Federal Ordinance on Emission Control (BImSchV) concerning Small-Scale Furnaces, in each case with notes and explanations. All these ordinances aim at reducing energy consumption in connection with heating; the 1st BImSchV also at air pollution abatement by lowering the permissible limiting values for soot and flue gas. The three ordinances also apply to housing property. (HSCH).
The microstructure of Al/{alpha}-Al{sub 2}0{sub 3} composites made by infiltrating Al into dense mullite preforms has been characterized using transmission electron microscopy. Observations revealed that the formation of the Al/Al{sub 2}0{sub 3} composites involves three stages. Initially, Al infiltrates into a dense mullite preform through grain boundary diffusion, and reacts with mullite at grain boundaries to form a partial reaction zone. Then, a complete reaction takes place in the reaction region between the partial reaction zone and the full reaction zone to convert the dense mullite preform to a composite of {alpha}-Al{sub 2}0{sub 3} (matrix) and an Al-Si phase (thin channels). Finally, the reduced Si from the reaction diffuses out of the Al/Al{sub 2}0{sub 3} composite through the metal channels, whereas Al from ...
Zr-Al metallo-organic compounds were thermally decomposed to prepare ZrO_2-Al_2O_3 composite powders. The specific surface area was dependent on the organofunctional groups of the starting organic compounds. The pore size distribution was dependent on the heating rate when the heating temperature was the same. 4 refs.; 4 figs.
The effect of phosphorus on the corrosion resistance of Al-bronzes is studied in detail in this work. A literature review showed that there are a lot of things known about the microstructure and the mechanical properties of Al-bronzes. In spite of their corrosion resistance the corrosion properties and the structure of the protective oxide films of Al-bronzes were seldom a matter of interest. Systematic studies of the influence of different alloying elements on the oxide film and the corrosion properties are rare. Therefore, it is not possible to predict the corrosion resistance of Al-bronzes, made by alloying particular elements. The high corrosion resistance of the new alloy CuAl_2_0P_1 was the reason to investigate the influence of phosphorus on the corrosion properties of Al-bronzes in more detail. A systematic study of the microstructure and the corrosion ...
The tribological properties of gas pressure sintered SiAlON and its composite with 18wt% silicon carbide (SiC) against two different mating materials, i.e., alumina and SiAlON are evaluated. SiAlON and SiAlON-18%SiC composite ceramics were prepared by pressure less sintering and gas pressure sintering. Fretting wear tests were carried out under dry unlubricated ambient conditions (room temperature 23-25^oC; relative humidity 50-55%) with a load of 8N for 45,000 cycles. Friction and wear properties of SiAlON-SiC proved better than the monolithic SiAlON. The formation of silica roll like structure on the composite worn surface was observed.
Hydrotalcites with different Al/Al+Mg ratios, and prepared at different pH and different aging temperatures of the gel were used as precursors of Mg-Al mixed oxides, and their textural and physicochemical properties were determined. A complete reaction network for the isopropanol decomposition on these catalysts has been established, and it is shown that the concentration of acetone in the products cannot always be used for a direct estimation of the rate of dehydrogenation. The Al/Al+Mg ratio for which the maximum in activity is obtained depends on the base strength needed for each particular reaction. For dehydrogenation of isopropanol, this is found at Al/Al+Mg [approx] 0.25. 36 refs., 10 figs., 2 tabs.
The effect of Al and Be ions pre-implantation on microstructural change and, the formation and growth of He bubbles in SiC/SiC composite was investigated. Four kinds of ion implanted specimens were prepared with 100 appm Al, 1000 appm Al, 100 appm Be and 1000 appm Be implanted. No microstructural change was observed in the matrices and fibers of SiC/SiC composites implanted with Al or Be ions up to 1000 appm. The un-implanted and Al or Be pre-implanted SiC/SiC composites were simultaneously irradiated to 10 dpa using triple ion-beams (6.0-MeV Si{sup 2+}, 1.0-MeV He{sup +} and 340-keV H{sup +}) at 1000 deg. C. Helium bubbles were formed in every matrix and fiber irradiated by triple ion-beams. The size of He bubbles in the matrix was increased by implanting Al or Be ions and increased with increasing amount of implanted Al or Be ions. The ...
The effect of Al and Be ions pre-implantation on microstructural change and, the formation and growth of He bubbles in SiC/SiC composite was investigated. Four kinds of ion implanted specimens were prepared with 100 appm Al, 1000 appm Al, 100 appm Be and 1000 appm Be implanted. No microstructural change was observed in the matrices and fibers of SiC/SiC composites implanted with Al or Be ions up to 1000 appm. The un-implanted and Al or Be pre-implanted SiC/SiC composites were simultaneously irradiated to 10 dpa using triple ion-beams (6.0-MeV Si"2"+, 1.0-MeV He"+ and 340-keV H"+) at 1000 deg. C. Helium bubbles were formed in every matrix and fiber irradiated by triple ion-beams. The size of He bubbles in the matrix was increased by implanting Al or Be ions and increased with increasing amount of implanted Al or Be ions. The size of He ...
Methods of X-ray diffraction and transmission electron microscopy were used to study the microstructure of dispersion-strengthened Cu-Al2O3 nanocomposites obtained by the method of simultaneous deposition of Cu and Al2O3 from the vapor phase. The effect of the size of particles of the oxide (Al2O3) and of their content on the electrical resistance of the composite has been considered. The results obtained make it possible to suppose that the main structural factor that determines the electrical resistance of the composite are nanodispersed particles of Al2O3 with a size of less than 20 nm.
AlN nanocrystalline layers and superstructures are used in the modern optoelectronic technology as reflecting mirrors in semiconductor layers. In the present work the properties of AlN films prepared by sputtering methods from an AlN target in reactive Ar + N plasma were investigated. The characterization was performed with HRTEM, SEM, glancing angle XRD and RBS methods. The present measurements confirmed the polycrystalline structure of AlN layers and enabled the evaluation of their grain size. The roughness and thickness of the layers were additionally determined by ellipsometric and profilometric measurements. (author)
The solubility limit of #alpha#'-SiAlON solid solutions on the Si_3N_4-YN:3AlN composition join in the system Si_3N_4-YN-AlN has been determined at 1800 degrees C. The end members of these solid solutions are Y_0_._4_3Si_1_0_._7Al_1_._3N_1_6 and Y_0_._8Si_9_._6Al_2_._4N_1_6. Unit-cell dimensions of the #alpha#'-SiAlON solid solutions in the system Si,Al,Y/N,O can be expressed as follows: a_0 (Angstrom) = 7.752 + 0.045m + 0.009n, c_0 (Angstrom) = 5.620 + 0.048m + 0.009n, where the #alpha#'-SiAlON solid solution has the formula Y_xSi_1_2_-_(_m _+ _n_)Al_m_+_nN_1_6_-_nO_n. The single-phase boundary of the solid solution #alpha#'-SiAlON on the composition triangle Si_3N_4-YN:3AlN-Al;N:Al_2O_3 is delineated. The present paper also reports the phase relationships ...
A new procedure for an efficient and sparing cleaning procedure of turbines was developed. The procedure uses cleaning and passivation chemicals that solve effectively and homogeneously salt and ferrous oxide coatings from turbines, avoiding attacks from corrosion, plugging and unbalances. In several high-pressure and condensation turbines the cleaning procedure has been already put into practice. (orig.)
Abstract Der folgende Artikel setzt die Reihe unserer ChiuZ-Beitrge zur Chemi- und Biolumineszenz mit einer interessanten und neuen experimentellen Arbeit zum -kalten Licht- spezieller ungesttigter Verbindungen fort, deren Anwendung auch in der modernen Zeit der Nanotechnologie im biochemischen bzw. medizinisch-chemischen Labor vllig neue Akzente gesetzt hat.
A knowledge based system for pitting corrosion is presented. It can be used for material selection for specific pitting corrosion conditions or to check the suitability of a chosen material. The user can enter his own knowledge. The expert system is an integration of traditional expert system technology and neural networks. (orig.)
This bibliographical study compiles and analyzes findings about the metabolism and resorption of molybdenum. Besides including studies on the physiology of molybdenum 99, a general survey is given on molybdenum in the environment and on its physiological behaviour. In particular, information on the dependence of molybdenum resorption on various factors, such as the chemical form, antagonisms etc., are gathered from literature. These factors have to be considered for sensibly carrying out necessary experiments.
The possibility of having Sr as an interstitial metal cation in #alpha#-SiAlON has been investigated in two systems: a single-cation system (Si_3N_4-SrO-AlN) and a multication system (Si_3N_4-(Y_2O_3/SrO/CaO)-AlN). It was found that Sr alone does not form #alpha#-SiAlON and that Sr could only be accommodated in #alpha#-SiAlON in conjunction with Y and Ca. The Sr content of #alpha#-SiAlON increased as the total content of (Y + Ca) increased and appeared to reach a limit at 0.5 at.%, or 0.15 atom per #alpha#-SiAlON. Unexpectedly, some of the #alpha#-SiAlON that contained (Sr + Y + Ca) was present as laths or fibers with the c-axis perpendicular to the hot-press direction.
Micro-Vickers hardness measurement has been used to determine the composition of functionally graded materials (FGMs). Materials used in the present study are Al-SiC, Al-Shirasu and Al-Al{sub 3}Ni FGMs, which are fabricated by a centrifugal method. The micro-hardness of the aluminum matrix for Al-SiC FGM markedly increases as the volume fraction of SiC particles increases. However, the tendency is not so clear in the cases of Al-Shirasu and Al-Al{sub 3}Ni FGMs. Plastic strain energy due to thermal misfits between the matrix and dipersed particles is calculated based on an elasto-plastic analysis by applying a shell theory after Lee et al. The hardness is correlated theoretically with the composition gradient through the mean plastic strain energy (responsible for dislocation density). It is concluded that the composition gradient of ...
The objective was to estimate oral Al bioavailability from tea infusion in the rat, using the tracer 26Al. 26Al citrate was injected into tea leaves. An infusion was prepared from the dried leaves and given intra-gastrically to rats which received concurrent intravenous 27Al infusion. Oral Al bioavailability (F) was calculated from the area under the 26Al, compared to 27Al, serum concentrationxtime curves. Bioavailability from tea averaged 0.37%; not significantly different from water (F=0.3%), or basic sodium aluminum phosphate (SALP) in cheese (F=0.1-0.3%), but greater than acidic SALP in a biscuit (F=0.1%). Time to maximum serum 26Al concentration was 1.25, 1.5, 8 and 4.8h, respectively. These results of oral Al bioavailabilityxdaily consumption by the human suggest tea can provide a si...
Here we report normal-state conductance measurements of three different types of superconducting tunnel junctions that are being used or proposed for quantum computing applications: p-Al/a-AlO/p-Al, e-Re/e-AlO/p-Al, and e-V/e-MgO/p-V, where p stands for polycrystalline, e for epitaxial, and a for amorphous. All three junctions exhibited significant deviations from the parabolic behavior predicted by the WKB approximation models. In the p-Al/a-AlO/p-Al junction, we observed enhancement of tunneling conductances at voltages matching harmonics of Al-O stretching modes. On the other hand, such Al-O vibration modes were missing in the epitaxial e-Re/e-AlO/p-Al junction. This suggests that absence or existence of the Al-O stretching mode might be related to the crystallinity of the AlO tunnel barrier and the interface between ...
Low-porosity #alpha#- and #beta#-SiAlON composite material was prepared when the powder mixture intended for preparation of yttrium #alpha#-SiAlON, with the formula Y_0_._4Si_1_2_-_m_+_nAl_m_+_nO_nN_1_6_- _n, was attritor milled in isopropyl alcohol or contained excess oxygen (n > 0.6). The region of stability of single-phase yttrium #alpha#-SiAlON was smaller at lower temperatures. Wet milling (in isopropyl alcohol) of AlN powder was found to introduce excess oxygen into the milled powder.
Moso bamboo (Phyllostachys pubescens) is widely distributed in the acid soil region of Southern China, where great potential of aluminum (Al) toxicity exists. To evaluate the Al tolerance of Moso bamboo, seed germination and root elongation were compared with two rice cultivars, and physical and physiological damages were examined under various levels of Al stress. Results showed that Moso bamboo seed germination was inhibited when Al concentration increased to 500 ?M, and the median lethal concentration was 2,000??M. Comparatively, the rice seed germination was not inhibited even at a concentration of 2,000??M Al. Aluminum accumulated mainly in the cell wall of root apices, and entered into protoplasts as treating time prolonged and/or Al concentration increased, which resulted in apoptos...
Low energy buildings promise significant energy savings and help climate preservation by cutting down on annual heating requirements to values below 70 kWh per m{sup 2} dwelling space. It is expected that low energy constructions will become the common standard by the year 2000 as a result of the forthcoming energy saving ordinance. For making the introduction and implementation of this standard successful, practical experience will be essential. For this reason, the state government of Hesse has supported respective pilot projects 1987. In 1989 the funding programme `30 low energy buildings in Hesse` has been established. Consecutively - between 1989 and 1993 - 29 buildings were erected. At first, the thermal quality of the crafted building construction including the ventilation systems was checked. Consecutively, energy consumption, indoor and outdoor temperatures were measured over a time span of several years. The experience of the inhabitants was surveyed. The `Institut Wohnen und ...
Magnetic resonance imaging (MRI) as a diagnostic imaging tool relies on the generation of magnetic fields, whereas the computerized tomography (CT) uses X-radiation. The fundamental principle of MRI is the magnetic resonance of paramagnetic atomic nuclei. These nuclei, as e.g. protons (= hydrogen nuclei), are aligned in required orientation by application of a strong magnetic field. Upon simultaneous application of an electromagnetic high-frequency field perpendicular to the axis of the basic magnetic field, and in response to periodical changing of the electromagnetic field at a given frequency, the originally aligned paramagnetic nuclei are forced into a movement similar to that of a ``whipping top``. When the resonance frequency is shut off, the nuclei return to their former, aligned positions, inducing a weak signal in a coil. The series of signals generated by multiple repetition of this process of excitation of nuclei and their return to aligned rest is used as input to a ...
Purpose: {sup 31}P-MRS is used to assess the influence of sex and age on quadriceps muscle metabolism before and after exercise. Materials and Methods: 32 healthy volunteers (15 women, 17 men; mean age: 38{+-}17 yrs.) were examined by dynamic phosphorus-31 ({sup 31}P) magnetic resonance spectroscopy (MRS). In the magnet, the quadriceps muscle was stressed by an isometric and an isotonic form of exercise until exhaustion, respectively. Results: Resting conditions: With increasing subjects` age, the ratio {beta}-adenosine triphosphate/total phosphate decreased (r=-0.37; p=0.02). With increasing subjects` age, the ratios inorganic phosphate/phosphocreatine (r=0.79; p=5x10{sup -8}), phosphomonoester/{beta}-adenosine triphosphate (r=0.74; p=10{sup -6}) and phosphodiester/{beta}-adenosine triphosphate (r=0.62; p=10{sup -4}) increased. The pH was the only one of the evaluated spectroscopic parameters which showed a sex-dependence: Female subjects had a significantly lower pH (7.03{+-}0.02) ...
Pr{sub 2}[Mo{sub 2}C{sub 3}] was obtained by arc melting of the elements followed by annealing at 1500 C in arc welded and sealed Mo-ampoules. The compound was characterised by chemical analyses, X-ray diffraction and metallography. The crystal structure (monoclinic, P2{sub 1}/c, Z = 4, a = 597.99(10) pm, b = 665.15(11) pm, c = 1185.60(19) pm and {beta} = 111.631(5) ) represents a new structure type containing a three dimensional polyanion {sub {infinity}}{sup 3}[(Mo{sub 2}C{sub 3}){sup 6-}] with Molybdenum(III) in a distorted tetrahedral coordination by carbo-ligands. Tetrameric building-blocks, Mo{sub 4}C{sub 10}, of edge sharing MoC{sub 4}-tetrahedra are arranged to form layers running parallel to (100). The layers are interconnected along [100] by sharing common apices of the MoC{sub 4} tetrahedra. The coordination polyhedra around praseodymium represent distorted (PrC{sub 5})-arrangements (mono capped tetrahedra and square pyramids). The metal atoms together form a distorted motif ...
Intermetallic compounds based on the Al-Co system were synthesized by solid state method - mechanical alloying and their properties were investigated using XRD, SEM, and DSC. The powder was used to make new targets of irradiation for gamma sources in order to enhance the specific activity and to reduce the consumption of material. The intermetallic compound AlCo was formed in the first 4 hours of milling. After 8 hours of milling the medium size of crystallites were of 5.58 nm. This value decreases with the increase of milling time up to 3 nm, corresponding to the 28 hours of grinding. There was calculated and plotted the Gibbs function, #DELTA#_f"0, for the reaction of formation AlCo and Al_3Co from the Al-Co system. It had negative values over the entire range of temperatures for both investigated compounds. After 28 hours milling a phase composition was obtained as follows: 0.2% ...
Different SiAlON composites based on #alpha#'-SiAlON are investigated, with respect to the phase relationships, densification behavior, and mechanical properties. The compositions are located on a phase-diagram line parallel to the Si_3N_4-Y_2O_3#centre dot#9AlN compound in the Si_3N_4-SiO_2-AlN-Al_2O_3-Y_2O_3-YN system. Analysis of the reaction sequences shows that the formation of the composites is associated with the transient appearance of Y_4Al_2O_9 (YAM), yttrium-aluminum-garnet (YAG), melilite, and a nitrogen-rich liquid phase. The small shift of compositions on the Si_3N_4-Y_2O_3#centre dot#9AlN compound phase-diagram line toward the Al_2O_3-rich side offers the advantage of a higher sinterability and the removal of the melilite phase from a wide range of compositions containing #alpha#'-SiAlON and polytypes. The ...
Engineering ceramics have excellent properties such as high strength, high hardness and high heat resistance compared with metallic materials. To apply the ceramic in fast reactor environment, it is necessary to evaluate the sodium compatibility and the influence of sodium on the mechanical properties of ceramics. In this study, the influence of high temperature sodium on the mechanical properties of sintered ceramics of conventional and high purity Al_2O_3, SiC, SiAlON, AlN and unidirectional solidified ceramics of Al_2O_3/YAG eutectic composite were investigated by means of flexure tests. Test specimens were exposed in liquid sodium at 823K and 923K for 3.6Ms. There were no changes in the flexural strength of the conventional and high purity Al_2O_3, AlN and Al_2O_3/YAG eutectic composite after the sodium exposure at 823K. On the contrary, ...
Crystalline ?-Al2O3 nanowires with diameter, 20?40?nm, length above 600?nm and aspect ratio above 30 have been successfully synthesized by thermal decomposition of boehmite (?-AlOOH) precursors obtained via hydrothermal route by using AlCl3, NaOH and NH3 as starting materials. Thermogravimetric analysis (TG), differential thermal analysis (DTA), X-ray diffraction (XRD), transmission electron microscope (TEM), selected area electron diffraction (SAED) and high resolution transmission electron microscope (HRTEM) were used to characterize the features of the as-made ?-Al2O3 nanowires and their ?-AlOOH precursors. The pH value of the solution and the mixed precipitant play important roles in the formation of ?-AlOOH nanowires. After calcination at 500?C for 2?h, the orthorhombic ?-AlOOH transf...
Whereas supersaturated aluminum alloys demonstrate enhanced passivity, conventional aluminum alloys spontaneously pit in air-saturated chloride solutions. We have concentrated on three areas: evaluation and characterization of Al-W alloys, which exhibit the best corrosion performance of any alloy system studied to date; characterization of the passive-film structure of Al-Mo alloys; and production and characterization of Al-W and Al-Ta powders, which will be used for compaction into bulk material. Surface analysis of the Al-W passive films formed during polarization show surprising little oxidized solute compared to other alloys. These results indicate that the barrier layer formation and electrostatic repulsion mechanisms used to explain the passivity of other alloys are not involved here. Instead the W may act to stabilize the passive film structure in a way similar to the way ...
Mg-Al mixed oxides with Mg/Al molar ratios of 0.5--9.0 were obtained by thermal decomposition of precipitated hydrotalcite precursors. The effect of composition on structure and surface and catalytic properties was studied by combining several characterization methods with ethanol conversion reactions. The nature, density, and strength of surface basic sites depended on the Al content. The catalyst activity and selectivity of Mg-Al mixed oxides in ethanol conversion reactions depended on composition. The dehydrogenation of ethanol to acetaldehyde and the aldol condensation to n-butanol both involved the initial surface ethoxide formation on a Lewis acid-strong base pair. The dehydration of ethanol to ethylene, and the coupling and dehydration to diethyl ether increased with Al content, probably reflecting the density increase of both Al{sup 3+}-O{sup 2{minus}} ...
... in Ti-6Al-4V has been studied quite thoroughly [5-7], much of the work resulting from the Air Force-sponsored High Cycle Fatigue initiative [8]. In ...
The Ti and Ti-Al coatings were deposited onto hot-worked AISI H11 steel substrates and plasma nitrided at 900 C. The Ti coated samples were successfully nitrided, while cracking and delamination of the Ti-Al coating was observed during nitriding. The formation of [delta]-TiN and [epsilon]-Ti[sub 2]N phases were detected after plasma nitriding of the Ti coating. During plasma treatment of the Ti-Al coating, the initial Ti[sub 3]Al and Al phases were paartially transformed into TiAl phase. The martensite transformation of the substrate material was found. The as-deposited Ti coating has a fibrous structure, while the structure of the as-sputtered Ti-Al coating is columnar. The superficial Vickers microhardness of plasma-nitrided Ti coating was 2200 HV 0.03 and the critical load of higher than 50 N indicates very good coating-to-substrate ...
Aluminium nitride (AlN) is a very interesting ceramic because of its combination of properties such as high thermal stability, high hardness and an unusual combination of high thermal and low electrical conductivity. But it is very difficulty to obtain an AlN layer on the aluminium substrates by thermochemical nitriding process. Since a thin film of aluminium oxide existing on the surface of every aluminium substrate prevents the nitrogen atoms from diffusing into the aluminium lattice. However, it is possible to sputter the oxide film away from the aluminium surface in a glow discharge with the use of plasma nitriding technique and to allow the formation of AlN layer on the aluminium bulk. In the present work specimen of aluminium Al 99.5 has been plasma nitrided in a modified plasma nitriding unit, in which a diffusion pump was used to obtain an especially low partial pressure of oxygen in the vauum ...
Photoluminescence properties and local electronic structures of rare earth (Eu^3^+ and Ce^3^+) activated Sr3AlO4F have been studied. X-ray powder diffraction data indicated that the activator ions of Eu^3^+ and Ce^3^+ can be incorporated into the Sr3AlO4F lattice and formed limited solid solutions of Sr3-2xLnxNaxAlO4F (Ln=Eu, Ce) with Na^+ as a charge compensator ion. The local structure around Sr sites was initially explored using Eu-activated Sr3AlO4F as a structural probe. Sr3AlO4F:Eu^3^+ exhibits orange-red emission ranging from 520 to 740nm with a maximum peak at about 619nm mainly originating from the ^5D0->^7FJ (J=0, 1, 2, 3, 4) transitions, indicating that Eu exists mainly in the trivalent state due to a strong oxidative lattice in Sr3AlO4F. Sr3AlO4F:Ce^3^+ shows an unusual long-wa...
OBJECTIVE: To determine the common types of injuries among children (0-14 years) in Al-Ain, United Arab Emirates (UAE). DESIGN: A retrospective descriptive hospital based study. SETTING: Al-Ain Medical...Full Text Available
BackgroundAmyotrophic lateral sclerosis (ALS), a common late-onset neurodegenerative disease, is associated with fronto-temporal dementia (FTD) in 3–10% of patients....Full Text Available
Aluminium (Al3+) toxicity is the primary factor limiting crop production on acidic soils worldwide. In addition to an application of lime for soil amelioration, Al3+ resistant plant varieties have been deployed to raise productivity on such hostile soils. This has been possible due to the exploita...
Aluminium (Al) toxicity, affecting around half of the world¿s arable land, severely hinders the ability of crop plants to utilize moisture and nutrients by restricting root growth and function. Among the cultivated cereals, rye is the most Al-tolerant and represents an important potential source of ...
The authors report on the nano-fabrication of GaN/AlGaN device structures using focused ion beam (FIB) etching, illustrated on a GaN/AlGaN heterostructure field effect transistor (HFET). Pillars as small as 20nm to 300nm in diameter were fabricated from the GaN/AlGaN HFET. Micro-photoluminescence and UV micro-Raman maps were recorded from the FIB-etched pattern to assess its material quality. Photoluminescence was detected from 300nm-size GaN/AlGaN HFET pillars, i.e., from the AlGaN as well as the GaN layers in the device structure, despite the induced etch damage. Properties of the GaN and the AlGaN layers in the FIB-etched areas were mapped using UV Micro-Raman spectroscopy. Damage introduced by FIB-etching was assessed. The fabricated nanometer-size GaN/AlGaN structures were found to be of good quality. The results demonstrate the ...
... Structures 9623595 P EPSCOR ENG DMI MATERIALS PROCESSING & MANUFCT Textile Engineering Department AL ... MPS DMR METALS, CERAMICS AND ELECT MATRS Materials and Mechanical Engineering AL Auburn University ...
Reactive milling of NiO + Al powder mixture resulted in the formation of NiAl-Al_2O_3 nanocomposite powders, with a crystallite size of about 20 nm. The Hall-Williamson analysis revealed that NiAl showed an orientation dependent crystallite size after short processing time and orientation dependent internal strain after long milling time. Both anisotropies were removed by heating the powders in the differential scanning calorimetry. Calorimetric studies showed one exothermic effect attributed to the reduction reaction of NiO and endothermic one associated with melting of Al. Two methods were applied for powders compaction: resistance sintering and pulse electric discharge. In both cases the densities of abut 90% of the theoretical value were achieved. A significant increase in average NiAl crystallites size in compacted samples was observed, up to several hundreds of ...
... 1984; Martin-Mora et al., 1995), and parasitism (Rothschild and Rothschild, 1939; Pesigan et al., 1958; Moose, 1963; Pan, ... effects of digeneans are variable; they may enhance (Rothschild and Rothschild...
A Ni3Al coating was prepared by plasma spraying technique on the surface of titanium alloy. Ni-Al mixed powders, coatings and reaction products were investigated by scanning electron microscope, EDS, DSC and XRD. A tight bonding between the coating and the substrate was formed. The X-ray diffraction analysis of the patterns showed that the coating not only had Ni3Al phase, but also had NiO and Al2O3 phase microcontent. Comparing Ni coated Al to Ni3Al at 900^oC, the diffusion was stronger and the diffusion layer was thicker. A minute pore structure was formed at 1200^oC in the front edge of solid-state reaction layer. So Ni3Al restrained the solid-state reaction of the coating with the substrate, and as a whole weakened the entry of oxygen atoms into the substrate and quenched the out-diffu...
The development of tough #alpha#-SiAlON with elongated grains in the last five years is summarized. This progress has been guided by the improved understanding of phase relations and nucleation/growth kinetics in SiAlON ceramics. Although most #alpha#-SiAlON compositions can be processed to contain some elongated grains, their microstructure, fracture toughness and R-curve behavior vary greatly. Such variability is due to the different phase stability of #alpha#-SiAlONs and the varying physical chemistry of the competing phases, including the transient/residual liquid. For this reason, microstructure control of #alpha#-SiAlON must pay close attention to the composition, starting powder and heating schedule. Seeding with single crystals of an appropriate #alpha#-SiAlON composition provides an attractive alternative that simplifies the task of microstructure ...
A microwave-assisted carbothermal reduction and nitridation (CTR/N) method has been used for successful preparation of monophasic #beta#'-SiAlON starting from kaolinite and carbon black. Phase pure #beta#'-SiAlON has been obtained in under 60 min in microwave field. The z value of microwave prepared #beta#'-SiAlON is found to be 2.95, which is very close to the expected value from kaolinite composition. Formation of #beta#'-SiAlON has been monitored with XRD and MASNMR of "2"9Si and "2"7Al; the possible reaction mechanism has been discussed. Kaolinite to #beta#'-SiAlON conversion appears to be a very rapid single-step reaction under microwave irradiation. #beta#'-SiAlON powders have been microwave sintered to 98.7% of theoretical density in 30 min.
Sialons are phases in the Si-Al-O-N and M-Si-Al-O-N systems where M includes Li, Mg, Ca, Sc, Y and the rare earth elements. They are comparable in variety with the mineral silicates and are built up of one-, two-, and three-dimensional arrangements of (Si,Al)(O,N)/sub 4/ tetrahedra in the same way that the structural units of the silicates are SiO/sub 4/ tetrahedra. These new materials include N-containing ceramics, glasses and glass-ceramics that are being explored for their thermal, chemical and physical properties.
Recently, Wang et al. proposed a three-party simultaneous quantum secure direct communication (3P-SQSDC) scheme with EPR pairs, which enables three involved parties to exchange their secret messages simultaneously by using an EPR pair. This work proposed an enhancement on Wang et al.'s scheme. With the enhancement, the communications in the improved 3P-SQSDC can be paralleled and thus improves the protocol efficiency.
Attempts to synthesize YPd[sub 2]Si-type representatives LnPd[sub 2]Al were successful only with Ln triple bond Ce, Pr, Nd. This orthorhombic structure (oP16; space group Pnma) is an ordered variant of the Fe[sub 3]C type. Only NdPd[sub 2]Al undergoes magnetic ordering above 2 K. (orig.)
Immobilization of long-lived fission products (LLFP) such as radioactive Tc, Cs and Sr into #alpha#-SiAlON ceramics was evaluated using stable isotopes instead of radioactive isotopes, and the applicability of #alpha#-SiAlON ceramics as the inert matrix for transmutation of LLFP was investigated. In the case of single addition of SrO, SrCO_3, Cs_2CO_3 or ReO_2 to the starting materials, #alpha#-SiAlON, single phase was not formed after hot-pressing. When Y_2O_3 was added with SrO, SrCO_3 or Cs_2CO_3 to the starting materials (#alpha#-Si_3N_4, AlN and #alpha#-Al_2O_3) in optimum compositions, #alpha#-SiAlON single phase was obtained after hot-pressing at 1700degC or 1800degC. From the EDS analysis, Sr and Y were detected from grains. It is suggested that Y would assist the expansion of interstices of #alpha#-SiAlON lattice, resulting in the ...
The ErNi{sub 1-} {sub x} Cu {sub x} Al compounds crystallize all in the hexagonal ZrNiAl-type structure. The concentration dependence of lattice constants shows a discontinuity between x=0.5 and 0.6. This structural change has no primary impact on the magnetic order in this series, but influences the crystal field. The lower part of the crystal-field energy-level schemes has been estimated from the specific-heat data.
The ErNi_1_- _x Cu _x Al compounds crystallize all in the hexagonal ZrNiAl-type structure. The concentration dependence of lattice constants shows a discontinuity between x=0.5 and 0.6. This structural change has no primary impact on the magnetic order in this series, but influences the crystal field. The lower part of the crystal-field energy-level schemes has been estimated from the specific-heat data.
Aluminium toxicity is a major problem in agriculture worldwide. Among the cultivated triticeae, rye (Secale cereale L.) is one of the most Al-tolerant and represents an important potential source of Al-tolerance for improvement of wheat. The Alt4 Al-tolerance locus of rye contains a cluster of genes...
Direct visualization of rare earths in @a- and @b-SiAlON unit-cells is performed through Z-contrast imaging technique in an aberration-corrected scanning transmission electron microscope. The preferential occupation of Yb and Ce atoms in different interstitial locations of @b-SiAlON lattice is demonstrated, yielding higher solubility for Yb than Ce. The triangular-like host sites in @a-SiAlON unit cell accommodate more Ce atoms than hexagonal sites in @b-SiAlON. We think that our results will be applicable as guidelines for many kinds of rare-earth-doped materials.
Continuous freestanding SiC(Al) films were fabricated by melt spinning the aluminum-containing polycarbosilane (A-PCS) precursor. The results showed that the films contained #beta#-SiC crystals, #alpha#-SiC nano-crystals, C clusters and small amount of Al_4O_4C and Al_4SiC_4. The Al atoms in the films played important roles as both sintering aids and grain growth inhibitor. The PL spectrum showed a wide luminescence band from 320 nm to 440 nm, and the origin of PL centered at 385 nm might be related to the #alpha#-SiC nano-crystals using quantum size effects. The obtained films are expected to have important applications in MEMS for the environment of high temperature and optoelectronic devices.
The local strain and texture in Al interconnect wires have been investigated using white and monochromatic x-ray microbeams on the MHATTCAT undulator beam line at the Advanced Photon Source. Intergrain and intragrain orientations were obtained with ~0.01 degree sensitivity using white beam measurements on wide Al pads (~100 Mu-m) and thin (2 Mu-m) Al wires. Orientation changes of up to 1 degree were found within individual grains of the (111) textured Al interconnects. Deviatoric strain measurements indicate small intragranular strain variations, but intergranular strain variations were found to be quite large.
Monolithic SiAlON ceramics are hard and brittle with little possibility for property design, but multi-phase SiAlON ceramics offer great scope for controlling microstructural development and desired properties. The ceramics can also be reinforced by separate additions of other hard, refractory compounds. The toughness in all these SiAlON composites can be increased by several mechanisms, and the best effect is reached if they are combined. When glassy phase is present, crack paths are affected by the strains caused by different thermal expansion of the glassy phase and the crystals and also by the interface properties. The crystal shape influence toughness, especially pronounced is the effect of the elongated #beta#- grains. Different toughening mechanisms are achieved by separately added reinforcement phases. The hardness is raised by the presence of #alpha# SiAlON and other hard constituents, such as ...
The thermal transformation of Al-base icosahedral phases was studied in-situ by real time neutron powder diffraction. Different compositions have been selected in order to vary the initial phase morphology and change the neutron scattering contrast between species. Alloys with low silicon and large aluminium contents produce first the orthorhombic O-Al_6Mn modification. In alloys with larger silicon content, the #alpha#-AlMnSi cubic phase appears soon after the beginning of the transformation but is still preceeded by O-Al_6Mn. Depending on compositions, the crystallization of the icosahedral phase is controlled either by the diffusion of Al through its interface with the residual fcc aluminium or that of Si within the bulk. The results are discussed in the light of current structural models. (author) 40 refs., 14 figs., 3 tabs.
We reported in previous papers that both the near-uv and the visible photosensitivities of ferroelectric-phase PLZT (lead lanthanum zirconate titanate) ceramics are increased by as much as four orders of magnitude by ion implantation or a combination of thermal diffusion of Al and ion implantation. New results are presented here on high-energy (1 MeV) implants of Al and Ni and coimplants of Al + Ne and Ni + Ne, and these results are compared with earlier 500 keV implants of Al and Cr and coimplants of Al + Ne and Cr + Ne as surface modification techniques for increasing the visible photosensitivity of PLZT. The important role of grain size in determining optimum contrast and resolution of stored optical information is described in terms of new experimental results.
GaP and AlGaP were grown by atmospheric pressure OMVPE on GaP substrates using tertiarybutylphosphine as the phosphorus source. A specular surface of GaP was obtained on a (100) just-oriented surface at 700deg C. Hazy but uniform thickness AlGaP was obtained. The growth efficiency for GaP was 1.2x10{sup 3}{mu}m/mol and that for AlGaP was 2.1x10{sup 3}{mu}m/mol.4.2 K photoluminescence showed near-edge emission from both GaP and AlGaP. (orig.).
Luminescence properties of SiAlON phosphors codoped with Ca and Yb were investigated by changing the host lattice composition. These modifications of the host lattice were obtained by replacing Si-N bonds by Al-N and Al-O bonds. Their photoluminescence (PL) and cathodoluminescence (CL) properties were measured and compared with each other. PL allows observing the influence of the host lattice modifications by measuring wider areas. CL can excite all luminescent centers, in particular the UV luminescence centers, even if their amount is small. Thus, two additional peaks in the ultraviolet and infrared regions were observed in CL, which is not observed by PL. This work suggests that the combination of PL and CL gives more understanding about the luminescence of SiAlON phosphors, in particular the role of the secondary phases on their properties.
An impingement jet system was used to study flow-assisted corrosion (FAC) of 3003 aluminum (Al) alloy in ethylene glycol-water solutions that simulates the automotive coolant by corrosion potential and electrochemical impedance spectroscopy (EIS) measurements as well as computational fluid dynamics (CFD) simulation. The effects of solution pH and fluid impact angle on Al FAC were determined. An increase of solution pH enhances the activity of Al due to dissolution of Al oxide film in alkaline environment. Moreover, Al activity decreases with the increasing fluid impact angle to the specimen. A CFD simulation shows that, with the increase of impact angle, the electrode area under high-velocity flow field decreases and that under low-velocity flow field increases. Consequently, the shear str...
Abstract The recent paper by Heyer et al. indicates that observations of size, linewidth and column density of interstellar clouds do not agree with simple virial equilibrium (SVE) as a balance between gravitational and kinetic energies in the sense that the clouds either have too much kinetic energy or too little mass to be bound. This may be explained by violation of SVE as suggested by Dobbs et al., by observational underestimation of the masses as suggested by Heyer et al. or by an external pressure acting as an additional confining force as suggested earlier by Heyer et al. The data of Heyer et al. cannot be explained with a single value for the external pressure, but if different clouds in the sample have different external pressures in the range of Pe/k= 104-107 cm-3-K, then most of...
A body-centered cubic (bcc) Mg-12Li-9Al-1Zn (wt.%) alloy was fabricated in air by electrolysis from LiCl-KCl molten salt at 500 deg. C. Electrolytic deposition of Li atoms on cathode (Mg-Al-Zn alloy) and diffusion of the Li atoms formed the bcc Mg-Li-Al-Zn alloy with 12 wt.% Li and only 0.264 wt.% K. Low K concentration in the bcc Mg alloy strip after the electrolysis process resulted from 47% atomic size misfit between K and Mg atoms and low solubility of K in Mg matrix.
A body-centered cubic (bcc) Mg-12Li-9Al-1Zn (wt.%) alloy was fabricated in air by electrolysis from LiCl-KCl molten salt at 500degreeC. Electrolytic deposition of Li atoms on cathode (Mg-Al-Zn alloy) and diffusion of the Li atoms formed the bcc Mg-Li-Al-Zn alloy with 12wt.% Li and only 0.264wt.% K. Low K concentration in the bcc Mg alloy strip after the electrolysis process resulted from 47% atomic size misfit between K and Mg atoms and low solubility of K in Mg matrix.
In this paper, we discuss various aspects of the development of an inverted-grown AlGaAs/GaAs cascade solar cell incorporating a patterned germanium tunnel junction. Topics include the development of the Al{sub 0.37}Ga{sub 0.63}As top cell, the growth of the GaAs bottom cell over the patterned germanium tunnel junction, and a technique for selective removal of thin AlGaAs/GaAs heterostructures after lattice-matched growth on germanium substrates. The problems to be overcome for the achievement of around 30% efficiencies in the AlGaAs/GaAs cascade cell under concentrator applications are also discussed. (orig.).
On behalf of the United Nations Environment Programme (UNEP) a study has been established by the Refrigeration, Air Conditioning and Heat Pump Technical Options Committee in which famous experts of refrigeration technology compiled facts which allow for a reliable prospect of real possibilities of changing from fluorine hydrogen to ozone innoxious substitutes and substitute technologies. With regard to the organization, a division into 6 committees for the establishment of the study has been made: 1. Refrigeration Options Committee, 2. Foams Options Committee, 3. Solvents, Coatings and Adhesives Options Committee, 4. Aerosols, Sterilants and Miscellaneous Uses Options Committee, 5. Halons Technical Options Committee and 6. Economic Options Committee. (BWI).
Purpose: calculation of conversion coefficients for the reconstruction of organ doses from entrance doses for abdomen radiographs of 0, 1, 5, 10, 15, and 30-year-old patients in conventional pediatric radiology for the radiographic settings recommended by the German and European guidelines for quality management in diagnostic radiology. Materials und method: using the commercially available personal computer program PCXMC developed by the Finnish Center for Radiation and Nuclear Safety (Saeteilyturvakeskus STUK), conversion coefficients for conventional abdomen radiographs were calculated performing Monte Carlo simulations in mathematical hermaphrodite phantom models describing patients of different ages. The possible clinical variation of beam collimation was taken into consideration by defining optimal and suboptimal radiation fields on the phantoms' surfaces. Results: conversion coefficients for the reconstruction of organ does in about 40 organs and tissues of the human ...
Modern oscillation- and analysis systems are often mentioned in the context of oscillation diagnosis which implies that this is a method of establishing the causes of the mechanical changes that cause the unwanted oscillation. Experience shows, however, that oscillation monitoring instruments can merely indicate oscillation symptoms at an early point in time. These findings must be interpreted in a machine-specific way and seen in the context of previous developments in order to establish the mechanical root cause of the matter. A 1000 MVA-generator shows that conventional oscillation measuring systems may also serve for diagnostic purposes within certain limits.(orig.) [German] Im Zusammenhang mit modernen Schwingungsmess- und Analysensystemen wird haeufig der Begriff der Schwingungsdiagnose verwandt und inpliziert, damit auch die Ursache von mechanischen Veraenderungen finden zu koennen, welche das beanstandete Schwingungsverhalten hervorruft. In der Praxis zeigt sich, dass dem Stand ...
Flow Tex and ABB Energiekabel GmbH have developed a technique which allows the recovery of cables without requiring any trenching works. The new technique was successfully used for the first time for a pilot project in 1995. The authors report on two recent recovery projects (1998) in which an optimised technology was used for recovering a total of 1 500 m system length of 110 kV low-pressure oil-filled cables in Stuttgart and Munich on very different conditions. The authors describe the operational experiences with the cable connections and highlight the background stipulating the removal of the cables. (orig.) [Deutsch] Ein Verfahren zur grabungsfreien Bergung von Kabeln, gemeinsam entwickelt von FlowTex und ABB Energiekabel, wurde erstmals in einem Pilotprojekt 1995 mit Erfolg eingesetzt. Die Verfasser berichten ueber zwei Bergungsprojekte, bei denen 1998 mit der optimierten Technik in Stuttgart und Muenchen insgesamt 1 500 Systemmeter ...
LP steam turbine retrofits are generally undertaken as a result of mechanical problems, for example due to stress corrosion cracking, torsional vibration or erosion. They present plant operators with an opportunity to introduce advanced aerodynamic technology, and at the same time improve efficiency and availability. Standard components, the majority proven in long-term service, can be used to obtain a permanent solution to the problems. In several European countries, retrofits have been carried out on intact LP steam turbines owned by utilities whose primary motivation is efficiency improvement. (orig.) [Deutsch] Niederdruck-Dampfturbinen werden in der Regel nur dann nachgeruestet, wenn waehrend des Betriebes Probleme durch Spannungsrisskorrosion, Torsionsschwingungen oder Erosion auftreten. In solchen Faellen bietet sich die Gelegenheit, eine moderne aerodynamische Loesung zu waehlen, die gleichzeitig Wirkungsgrad und Verfuegbarkeit verbessert. Es wird gezeigt, dass hierfuer eine ...
In the first part of the symposium, experts reviewed the state of the art of decentralized waste water treatment in Europe. In the second part, exemplary solutions in Poland and the Czech Republic were presented. The final part was dedicated to future concepts and strategies. [German] Im Herbst letzten Jahres hat die Kommunale Umwelt-AktioN U.A.N. in einer Abfolge von drei Abwasserfachsymposien Expertenrunden zum Austausch ueber den aktuellen Stand des Wissens zum Thema dezentrale Abwasserbehandlung veranstaltet. Mit dem Internationalen Symposium 'Konzepte zur Abwasserbehandlung im laendlichen Raum Europas' in Celle hat das Projekt der U.A.N. seinen Abschluss gefunden. Der Konzeption des Projektes entsprechend haben im 1. Teil des Symposiums Experten ueber den Stand der Entwicklung auf dem Sektor der dezentralen Abwasserbehandlung in Deutschland berichtet. Im 2. Teil unserer Fachtagung wurden europaeische Beispiele fuer dezentrale Loesungen aus ...
Endoluminal vascular prostheses that can be implanted by percutaneous routes represent the most recent development in vascular interventional radiology. Various commercially available types of prosthesis are presented and the construction principles and applications are described. At present secure indications for the implantation of endoluminal prostheses are limited to the elimination of aneurysms and arteriovenous fistulae of the large vessels near the trunk in sections that do not cross a joint. The wide use in peripheral occlusive diseases cannot yet be recommended because confirmed data are not available. (orig.) [German] Endoluminale Gefaessprothesen, die perkutan implantierbar sind, stellen die juengste Entwicklung in der vaskulaeren interventionellen Radiologie dar. Verschiedene kommerziell erhaeltliche Prothesentypen werden vorgestellt, ihr Konstruktionsprinzip und ihre Applikation erlaeutert. Die gesicherten Indikationen zur endoluminalen ...
For the calculation of humidifier systems in supply air systems nomographs and appropriate software are not sufficient alone. System design factors must be considered, also. On the basis of a clear definition interpretation examples are described and remarks for the effective installation of steam distribution systems are given. (orig.) [Deutsch] Es ist nicht zu empfehlen, Befeuchterstrecken bzw. Dampfdiffusionsstrecken ausschliesslich ueber Nomogramme oder ueber eine entsprechende Software auszulegen. Zumindest sollte vorher genauestens geprueft werden, welche Parameter in die Berechnung mit einfliessen. Zur exakten Berechnung der Absorptionsstrecken in Zuluftsystemen muessen auch anlagenspezifische Faktoren beruecksichtigt werden. Die Erfahrung hat jedoch gezeigt, dass dem Begriff `Befeuchterstrecke` zu wenig Aufmerksamkeit gewidmet wird. Hierdurch koennen Fehler entstehen, die nur mit relativ hohem finanziellem Aufwand wieder zu korrigieren sind. Grundsaetzlich ...
In the last two years, the VDMA work group 'Functional security' compiled a qualitative and quantitative procedure for the determination and evaluation of turbo-machine specific risks. With the calibrated risk graph for turbo-machines the requirements (Safety Integrity Level SIL) to the protective functions for turbo-machines (steam turbines, gas turbines, generators and compressors) were determined. With consideration of the legislation, the work group compiled a recommendation for the renewal and/or reconstruction of protective functions with old facilities.
A report is given of investigations into the possibility of utilizing red mud from the Bayer process for producing Ferrari cements. On repeated burning at 1450deg C suitable mixtures of red mud with silica and lime form a clinker with a low free lime content from which Ferrari cement can be produced. The average 28-day compressive strengths of cements produced from this clinker are so encouraging that further investigations are appropriate. (orig.).
There is much interest worldwide in low-emission, low-noise electric cars. Modern vehicles with advanced technology are an interesting alternative to conventional cars. (orig.) [Deutsch] Das Interesse an den emissionsfreien und leisen Elektroautos ist weltweit ungebrochen. Die heute verfuegbaren Fahrzeuge zeigen die betraechtlichen, in den letzten Jahren erzielten Fortschritte, die sie fuer immer mehr Anwender zu einer beliebten Alternative zur Benutzung des konventionellen Autos machen. (orig.)
A manipulator for checking the inside of a vertical, flange-shaped collector of a horizontal steam generator consists of a rotating mast with bearings at the top and bottom ends with a support that can be moved along the length of the mast for the checking system mountings. The support is propelled by a drive spindle placed parallel to the mast with its drive head bearing in the support and locked into a toothed rack attached to the mast. The checking system mountings are fitted in or on the walls of the support and are very close to the box-shaped support. Their retractable arms are hinged.
Progress reports on the European Research Centre for Air Pollution Control Measures project are presented. Topics covered were: assessment and analysis of the impacts of airborne pollutants on forest trees, and distinction from other potential causes of recent forest dieback; research into atmospheric dispersion, conversion and deposition of airborne pollutants; development and optimization of industrial technical processes to reduce or avoid emissions; and providing instruments and making recommendations to the industrial and political sectors.
In order to improve the capacity and service life of cathodes, the effect of carboxy-methyl cellulose, soot, silica gel and fibres was examined. Structural tests and electrical and electro-chemical measurements are used for this. The additives can affect crystallization in the manufacturing stage of the electrodes and can increase the storage capacity for water and the electronic conductivity. They act to stabilize the mass in cyclic operation. Soot additive has little effect on the properties of the electrode, but the other substances increase the service life or the use of the mass. (LU).
In the well-known devices for increasing the decontamination factor in the treatment of radioactive waste water by evaporation, which consist of narrowing devices with evaporator sump and condenser, droplets of liquid and solid particles are carried over from the breeder space, which are radioactive and therefore make the decontamination factor worse. Better results are obtained if one places a fibre bed filter between the evaporator sump and the condenser, preferably in a horizontal connecting pipe between the evaporator sump and the condenser.
In recent years very good experience has been accumulated with self-supporting low-pressure blades. Today blades are constructed up to a length of 1060 mm (50 Hz) or 1360 mm (25 Hz). In this process modern computational methods from aerodynamics and also from mechanics are employed. The further development of computer technology also permits new methods, for example the use of curved fixed blading as well as the optimization of existing designs. (orig.).
Heterostructures based on AlGaInP alloy compounds are very attractive for visible semiconductor lasers, heterojunction bipolar transistors (HBTs), and high-electron-mobility transistors (HEMTs) lattice matched to GaAs substrates. Several wet etching solutions for AlGaP of different compositions have been studied. Al{sub 0.5}Ga{sub 0.5}P is found to etch in HF, H{sub 3}PO{sub 4}, hyphosphorous acid (HOPH{sub 2}:O), HCl, KOH, and 1% Br{sub 2}-methanol (MeOH). Etching of Al{sub 0.5}Ga{sub 0.5}P in HCl is reaction limited with an activation energy of {approximately}54.4 kJ/mol. At fixed conditions, the etch rates of Al{sub x}Ga{sub 1{minus}x}P vary exponentially with x in HF and HCl, while in 1% Br{sub 2}-MeOH and mixtures of HCl and HNO{sub 3} the etch rates follow a linear dependence on AlP mole fraction. HF has been found to be a good etchant for ...
FeAl, which has high oxidation and sulfidation resistance, was shown to be thermodynamically compatible with WC. Calculations indicate that soly. of WC in liq. Fe-40at.%Al at 1450 C is about 2 at.%. Since liquid FeAl wets WC very well, the WC/FeAl system lends itself to liquid-phase sintering, resulting in close to theoretical densities. Almost fully dense cermets with 20.6 wt% FeAl binder were produced. With one-step infiltration, 98% dense cermets with only 7 wt% FeAl binder were fabricated. RT bend strengths and fracture toughness for WC-20.6 wt% FeAl reached 1680 MPa and 22 MPa{center_dot}m{sup 1/2}. Ductile binder fracture was observed on the fracture surfaces. Pores containing oxide inclusions were found, suggesting that improvements in processing are likely to further improve the mechanical properties. Insufficient process control may ...
Rare earth stabilised #alpha#-SiAlONs are commonly observed with an equiaxed grain morphology. Elongated #alpha#-SiAlON has been observed in some of these systems, however it usually results from special techniques such as pressure sintering. The formation of elongated #alpha#-SiAlON grains during pressureless sintering has been shown to commonly occur in the Ca #alpha#-SiAlON system. Examination of phase and microstructural development in three Ca #alpha#-SiAlON compositions in the temperature range 1400 deg to 1800 deg C showed that phase development and grain growth occurred at different temperatures. It was found that chemical reactions were completed by 1550 deg C, however significant grain growth did not occur at this temperature. Grain growth progressed from 1600 deg C and continued up to 1800 deg C, the maximum temperature investigated. At 1800 deg C, ...
The occurrence of stable decagonal quasicrystalline phase in Al-Co-Ni and Al-Cu-Co alloys through conventional solidification is well established. Earlier, we have studied the effect of Cu substitution in place of Co in the Al_7_0Co_1_5Ni_1_5 alloy. Here we report the structural/micro-structural changes with substitution of Cu for Ni in rapidly solidified Al-Co-Ni alloys. The melt spun ribbons have been characterized using X-ray diffractometry, scanning and transmission electron microscopy. With an increase in Cu content in the melt spun Al_7_0Co_1_5Cu _xNi_1_5_-_x (x = 0-15 at.%) alloys, the relative amount of the decagonal phase decreased up to 10 at.% of Cu. At this composition, the quaternary alloy showed the co-existence of decagonal quasicrystal and superstructure of #tau#_3 vacancy ordered crystalline phases. The decagonal phase containing Cu showed more disordering than ...
Inductively coupled plasma etching of InGaP, AlInP and AlGaP in BI{sub 3} or BBr{sub 3} discharges was investigated as a function of source power, dc chuck bias and plasma composition. InGaP etches at the fastest rates ({gt}6000thinsp{Angstrom}thinspmin{sup {minus}1}) in both chemistries, followed by AlGaP. It is found that AlInP provides an excellent etch stop for the other two materials in both mixtures. The InGaP surface morphology improves with increasing BI{sub 3} or BBr{sub 3} content, and with increasing dc chuck bias. The etched features for this material are highly anisotropic. Etch selectivities for InGaP over SiO{sub 2} and SiN{sub x} of {ge}8 are obtained in both plasma chemistries, and there is no etch incubation time with either mixture, indicating that both can scavenge the native oxide on InGaP, AlGaP and AlInP. {copyright} {ital 1998 American ...
Inductively coupled plasma etching of InGaP, AlInP and AlGaP in BI_3 or BBr_3 discharges was investigated as a function of source power, dc chuck bias and plasma composition. InGaP etches at the fastest rates (>6000 Angstrom min"-"1) in both chemistries, followed by AlGaP. It is found that AlInP provides an excellent etch stop for the other two materials in both mixtures. The InGaP surface morphology improves with increasing BI_3 or BBr_3 content, and with increasing dc chuck bias. The etched features for this material are highly anisotropic. Etch selectivities for InGaP over SiO_2 and SiN_x of #>=#8 are obtained in both plasma chemistries, and there is no etch incubation time with either mixture, indicating that both can scavenge the native oxide on InGaP, AlGaP and AlInP. copyright 1998 American Vacuum Society.
High lithium-ion (Li^+) conductive garnet-structured lanthanum lithium zirconate (LLZ) solid electrolyte is prepared by incorporation of appropriate amounts of silicon (Si) and aluminum (Al). The resultant pelletized LLZ obtains total Li^+ conductivity of 6.8x10^-^4Scm^-^1 at 298K. This improved conductivity is nearly identical with the bulk Li^+ conductivity of the LLZ reported earlier, suggesting that the grain boundary resistance is effectively reduced by the incorporation of Si and Al. Microanalyses by transmission electron microscopy coupled with energy-dispersive X-ray microanalysis and electron energy-loss spectroscopy revealed the presence of amorphous Li-Al-Si-O with nano crystalline LiAlSiO4 at grain boundaries. Fast lithium-ion transport around the amorphous Li-Al-Si-O/LiAlSiO4 ...
Focus ion beam (FIB) technology is a commonly used tool for integrated circuit device modification, failure analysis, and a variety of other applications. However, limited reliability data of FIB altered circuit is available. This study describes the electromigration mechanism of FIB-altered Al(Cu-Si)/Ti-layered metal lines. The electromigration failures encountered resulted in Al voids at the anode end of FIB-deposited W and Al{sub 2}Cu precipitates at the cathode end. A higher frequency of Al extrusions was also observed on samples stressed at higher temperatures. These observations indicated that FIB-W was an effective blocking boundary for Al and Cu, and confirmed that Cu does electromigrate before Al. The electromigration mechanism of the FIB-altered line closely resembles the published results from two-level Al/W-line/stud interconnect ...
We studied the effects of co-doping with Li and Al on the energy gaps of MgB2 by performing point-contact Andreev-reflection spectroscopy (PCAR) in polycrystalline Mg1-x(Al?Li1-?)xB2 samples with x?0.4. Even though the lattice parameters and the critical temperature of the compound simply scale with the effective Al content ?x, irrespective of the Li concentration, the energy gaps do not. In particular, for a given effective Al content, the comparison with Mg1-y(Al)yB2 with y = ?x shows that the ? bandgap is practically the same while the ? bandgap is higher. A clear gap merging is observed in the most doped sample (x = 0.4) when Tc<20 K. The results are discussed within the two-band Eliashberg theory and compared to the outcomes of first-principles calculations of the effects of Li and Al co-doping on the electronic structure of magnesium diboride.
Cyclic voltammetry (CV), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were employed to investigate the electrodeposition of Eu and Al in an LiCl-KCl eutectic melt containing Eu{sup 2+} and Al{sup 3+} at 450 deg. C. In order to deposit a pure Eu and Al alloy, the stoichiometrically lower concentration of Al{sup 3+} than that of Eu{sup 2+} and Al wires as a counter electrode was introduced into the bath of LiCl-KCl melt for the electrodeposition. The electrodeposition takes place at a potential more negative than -1.95 V vs. Ag|Ag{sup +} while the deposit is oxidized at more positive potential than -1.92 V. Two new reduction peaks and an anodic peak on a W working electrode were observed at -2.39 V, -2.42 V, and -2.1 V, vs. Ag|Ag{sup +}, respectively, suggesting that the potential window of the Al system in LiCl-KCl melt can be ...
Cyclic voltammetry (CV), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were employed to investigate the electrodeposition of Eu and Al in an LiCl-KCl eutectic melt containing Eu2+ and Al3+ at 450 deg. C. In order to deposit a pure Eu and Al alloy, the stoichiometrically lower concentration of Al3+ than that of Eu2+ and Al wires as a counter electrode was introduced into the bath of LiCl-KCl melt for the electrodeposition. The electrodeposition takes place at a potential more negative than -1.95 V vs. Ag|Ag+ while the deposit is oxidized at more positive potential than -1.92 V. Two new reduction peaks and an anodic peak on a W working electrode were observed at -2.39 V, -2.42 V, and -2.1 V, vs. Ag|Ag+, respectively, suggesting that the potential window of the Al system in LiCl-KCl melt can be extended to -2.43 V vs. Ag|Ag+. The EDS ...
Blades of modern steam turbines are designed for high efficiency and operational safety. Modern computer programs enable optimisation of design but factors like manufacturing, assembly, operation and downtimes still play an important role. Damage statistics show that blade damage still quite frequent. Selected cases from the Allianz damage assessment centre show some of the more frequent damage mechanisms. Damage is often caused when several factors come together. Prevention of follow-up damage requires early identification of beginning damage.(orig.) [German] Die Auslegung der Beschaufelung moderner Dampfturbinen hat die Vorgabe, einen hohen Wirkungsgrad bei gleichzeitig hoher Betriebssicherheit zu erreichen. Mit den heute zur Verfuegung stehenden Rechenprogrammen ist eine entsprechende Optimierung realisierbar. Fuer die langzeitige Betriebsbewaehrung haben aber Einflussgroessen aus Fertigung, Montage, Betrieb und Stillstand auch heute noch die gleiche Bedeutung ...
The presented paper describes the formulation of the fractional mass balances which are used to calculate the concentration and size distribution of char in the balance cells of a circulating fluidized bed boiler. In case of using the shrinking core model additionally the distribution of conversion of the char particles is calculated. Basically two reaction models (a shrinking particle and a shrinking core model) are available to describe the combustion process. The model considers all essential physico/chemical phenomena (primary fragmentation, attrition, mass transfer to gas phase) which have to be taken into account for the description of the combustion process. The model is part of an overall simulation program for circulating fluidized bed boilers. This engineering simulator has been developed to return the main performance parameters of such systems like temperature along the furnace height, size distribution of balanced solid components, heat flows at the different heat ...
Early in 1988 RWE decided to overhaul the power station at Goldenberg. This was necessary due to the age of the plant, the obligation to supply heat and process steam and recent amendments of environmental legislation. After analysing demands and needs one developed a plant concept with a 290 t/h and a 400 t/h steam generator. Due to lack of space the decision was made in favour of a circulating atmospheric fluidised bed combustion instead of steam generators with pulverised lignite combustion as these steam generators take up much more space due to the legally required desulphurisation plants for gaseous emissions. Apart from generating steam RWE wishes to gain experience with this combustion technology and test it for suitability and use in large-scale plant. (orig./KO) [Deutsch] Aufgrund des fortgeschrittenen Alters, der aktuellen Umweltschutzgesetzgebung sowie bestehender Versorgungsverpflichtungen fuer Waerme und Prozessdampf wurde Anfang 1988 von der RWE Energie AG in Essen die ...
Experts tend to disagree about the economic effects of air pollution abatement measures. This book, which addresses also non-experts, explains the analytical background on the basis of available data. The authors conclude that there is a wide range of political options for achieving the goal of air pollution abatement. They differentiate between the various levels of discussion and show how misinterpretations of scientific results come about, thus making an important contribution to a discussion that is based on facts rather than emotions. [German] Die Einschaetzungen zur wirtschaftlichen Bewertung von Klimaschutzmassnahmen, insbesondere zur Steigerung der Energieeffizienz, sind sehr widerspruechlich. Dieses Buch erlaeutert anhand von Zahlenmaterial die analytischen Hintergruende und ist auch fuer Nicht-Oekonomen verstaendlich geschrieben. Die Autoren kommen zu dem Schluss, dass in vielen Bereichen rentable Energiesparpotentiale nicht erkannt ...
For millions of people general noise and especially traffic noise are the main sources of environmental pollution. The increasingly stricter noise pollution abatement limiting values laid down by the law call for motor vehicle noise pollution abatement measures. Within the framework of today`s cost- and performance-oriented automobile and engine development developing engineers are required to reduce noise levels. The present state of the art is described and future possibilities of combustion engine structure-borne noise calculation and optimization are discussed from the point of view of K + P Computerunterstuetzte Strukturanalysen GmbH. (orig.) [Deutsch] Laerm allgemein und dabei speziell wiederum der Verkehrslaerm steht fuer Millionen von Menschen an allererster Stelle der persoenlichen Belastung durch die Umwelt. Zur Minderung der Laermbelastung werden vom Gesetzgeber immer schaerfere Grenzwerte vorgeschrieben, die dazu zwingen, Massnahmen ...
TRITEX was a pumped loop with Pb-15.8Li, fabricated from steel 1.4922. In contact with the molten eutectic were also molybdenum, vanadium and armco-iron. The loop was originally designed to investigate tritium extraction using solid getter metals. Over the years the goal changed to the study of metals, corrosion products and purification of the eutectic mixture. Therefore many modifications were done. The first part of this report describes TRITEX. All parts were enclosed in thermoboxes for a homogeneous temperature. One test section was in an argon glove box and could be opened during operation. Other special equipment`s were: permeation membranes and liquid-metal-covergas-interfaces to study the transport of H{sub 2}, D{sub 2} and {sup 3}H, different purification devices, a quartz observation window to see the liquid metal surface, 4 different kinds of flow measurements, level indicators, freeze valves. The second part describes loop operation. Between 1989 and 1996, the eutectic ...
Hexavalent Cr has been identified as one of the toxic metals commonly present in industrial effluents. Among the treatment techniques developed for removing Cr(VI) from waste waters, sorption is most commonly applied, due to its simplicity and efficiency. However, few adsorbents can be recycled and reused cost-effectively. In this study, the removal and recovery of Cr(VI) from water using Li/Al LDH was investigated. The removal of Cr(VI) by Li/Al LDH was evaluated in a batch mode. The results demonstrated that Cr(VI) adsorption onto Li/Al LDH occurs by replacing the Cl{sup -} that originally exists in the interlayer of the adsorbent. The degree of Cr(VI) adsorption observed for Li/Al LDH was relatively high and the process occurred rapidly; however, a portion of adsorbed Cr(VI) was gradually desorbed, due to the Li de-intercalation of Li/Al LDH. Lithium de-intercalation from ...
We describe the growth, fabrication, and characterization of an ultraviolet (UV) photoconductive detector based on In{sub x}Al{sub y}Ga{sub 1-x-y}N quaternary alloy that is lattice matched to GaN. The detector consisted of 0.1 {mu}m In{sub x}Al{sub y}Ga{sub 1-x-y}N alloy grown on 0.5-1.0 {mu}m GaN epilayer by metalorganic chemical vapor deposition. With varying indium concentration, the cut-off wavelength of the In{sub x}Al{sub y}Ga{sub 1-x-y}N detectors could be varied to the deep UV range. The most important and intriguing result is that the responsivity of the In{sub x}Al{sub y}Ga{sub 1-x-y}N quaternary alloy exceeded that of AlGaN alloy of a comparable cutoff wavelength by a factor of five. This makes the nitride quaternary alloy very important material for solar blind UV detectors applications particularly in the deep UV range where Al rich ...
We describe the growth, fabrication, and characterization of an ultraviolet (UV) photoconductive detector based on In_xAl_yGa_1_-_x_-_yN quaternary alloy that is lattice matched to GaN. The detector consisted of 0.1 #mu#m In_xAl_yGa_1_-_x_-_yN alloy grown on 0.5-1.0 #mu#m GaN epilayer by metalorganic chemical vapor deposition. With varying indium concentration, the cut-off wavelength of the In_xAl_yGa_1_-_x_-_yN detectors could be varied to the deep UV range. The most important and intriguing result is that the responsivity of the In_xAl_yGa_1_-_x_-_yN quaternary alloy exceeded that of AlGaN alloy of a comparable cutoff wavelength by a factor of five. This makes the nitride quaternary alloy very important material for solar blind UV detectors applications particularly in the deep UV range where Al rich AlGaN alloys have problems with low ...
Copper coatings deposited on Al-6061 substrates by radio frequency magnetron sputtering, to prevent the retention and permeation of energetically implanted tritium in Al-6061, were evaluated by a variety of characterization techniques. The coatings, weighing in the 0.03 to 0.088 kg/m{sup 2} range, were smooth and had a fine grain structure. They contained the intermetallic phases Cu{sub 9}Al{sub 4} and CuAl{sub 2} as well as copper. The fractions of Al and Cu in any coating increased and decreased, respectively, with increasing depth below the surface. Furthermore, the fractions of Al and Cu on the coating surface decreased and increased, respectively, with increasing coating weight. There was no texture or preferred orientation in the Cu phase of the coatings. A significant amount of oxygen was also detected at the original substrate surface. Residual stress ...
A one-nanometer scale transmission electron microscope electron probe X-ray microanalysis characterization of as-deposited and annealed aluminum--11.5 at.% zirconium multilayer samples in cross-section synthesized by magnetron sputtering is reported on here. Composition line profiles were acquired across Zr layers in as-deposited material and samples isochronally annealed in a differential scanning calorimeter to temperatures of 290 C and 485 C. A spatial resolution of approximately 1.5 to 2.0 nm was achieved in these experiments and will be improved by deconvolution of the instrumental electron probe function from the data. The as-deposited structure consisted of crystalline Al and Zr layers with thin amorphous layers at the Al/Zr interfaces. The amorphous interface layers increased in thickness upon annealing to 290 C. Additionally, at 290 C a metastable cubic alloy forms at the Zr deposited on Al interface. Upon heating ...
The visible semiconductor laser includes an InAlGaP active region surrounded by one or more AlGaAs layers on each side, with carbon as the sole p-type dopant. Embodiments of the invention are provided as vertical-cavity surface-emitting lasers (VCSELs) and as edge-emitting lasers (EELs). One or more transition layers comprised of a substantially indium-free semiconductor alloy such as AlAsP, AlGaAsP, or the like may be provided between the InAlGaP active region and the AlGaAS DBR mirrors or confinement layers to improve carrier injection and device efficiency by reducing any band offsets. Visible VCSEL devices fabricated according to the invention with a one-wavelength-thick (1{lambda}) optical cavity operate continuous-wave (cw) with lasing output powers up to 8 mW, and a peak power conversion efficiency of up to 11%. 5 figs.
The effect of interfacial structure on the mechanical properties of aluminum-ceramic composite materials fabricated by liquid phase sintering was studied. The composites were based on two matrix alloys (powder metallurgy alloys 201 and 601) reinforced with either Al{sub 2}O{sub 3} or SiC particulate. Characterization of the interfacial regions demonstrated that the SiC-matrix interfaces were faceted whereas the Al{sub 2}O{sub 3}-matrix interfaces had an incomplete layer of a silicon-rich amorphous phase. Preferential attack of the particles during sintering is believed to cause the crystallographic facets to form on SiC. Locally high silicon concentrations near Al{sub 2}O{sub 3} particles led to the formation of a glassy phase from the reduction of Al{sub 2}O{sub 3}. The difference in interfacial structure resulted in a higher particle-matrix bond strength and therefore improved composite mechanical ...
The alloying of steel surface with aluminum (Al) using Microsecond-pulsed Intense Electron Beams (MIEB-Al) was developed and optimized in order to be used for improving the corrosion resistance of the 316, 1.4970 and T91 steels, exposed to liquid Pb and Pb-Bi-eutectic. The procedure consists in two steps: (i) coating the steel surface with Al or an Al-containing alloy layer and (ii) melting the coating layer and the steel surface layer using intense pulsed electron beam. In order to cover the steel surface with an homogeneous and crack-free Al-alloyed layer, the following experimental conditions are required: Al coating thickness range 5-10mm, electron kinetic energy 120keV; pulse duration 30ms; energy density 40-45J/cm2; number of pulses 2-3. Using the mentioned procedure, the corrosion r...
Abstract A next generation material for surface passivation of crystalline Si is Al2O3. It has been shown that both thermal and plasma-assisted (PA) atomic layer deposition (ALD) Al2O3 provide an adequate level of surface passivation for both p- and n-type Si substrates. However, conventional time-resolved ALD is limited by its low deposition rate. Therefore, an experimental high-deposition-rate prototype ALD reactor based on the spatially separated ALD principle has been developed and Al2O3 deposition rates up to 1.2-nm/s have been demonstrated. In this work, the passivation quality and uniformity of the experimental spatially separated ALD Al2O3 films are evaluated and compared to conventional temporal ALD Al2O3, by use of quasi-steady-state photo-conductance (QSSPC) and carrier density ...
The pozzolanic behaviour of compound-activated red mud-coal gangue has been investigated through TG, DTA, XRD, FTIR and {sup 27}Al MAS NMR. From viewpoint of reaction kinetics, it is found that the pozzolanic reaction mechanism of the compound-activated red mud-coal gangue-lime system is clearly consistent with diffusion control up to 14 days, and the reaction rate constant calculated from Jander equation decreases with the increase of CaO addition in the system. The hydration products formed in the red mud coal gangue-lime systems at ambient temperature are essentially aluminous C-S-H and Ca{sub 3}Al{sub 2}O{sub 6} center dot xH{sub 2}O. From TG analysis results, it is thought that the high amount of Ca(OH){sub 2} in the pastes of studied system is not conducive to the continual increase of non-evaporable water content of the hydration products. Of particular interest. {sup 27}Al MAS NMR proved to be an effective technique ...
The pozzolanic behaviour of compound-activated red mud-coal gangue has been investigated through TG, DTA, XRD, FTIR and 27Al MAS NMR. From viewpoint of reaction kinetics, it is found that the pozzolanic reaction mechanism of the compound-activated red mud-coal gangue - lime system is clearly consistent with diffusion control up to 14 days, and the reaction rate constant calculated from Jander equation decreases with the increase of CaO addition in the system. The hydration products formed in the red mud-coal gangue - lime systems at ambient temperature are essentially aluminous C-S-H and Ca3Al2O6.xH2O. From TG analysis results, it is thought that the high amount of Ca(OH)2 in the pastes of studied system is not conducive to the continual increase of non-evaporable water content of the hydration products. Of particular interest, 27Al MAS NMR proved to be an effective technique to obtain valuable information of ...
For optimizing the microstructure of the (#alpha# + #beta#)-titanium alloy TiAl5Fe2.5 the content of the two alloying elements aluminium and iron in the #alpha#- and #beta#-phase was determined by microprobe analysis. The alloys with the composition of the #alpha#- and of the #beta#-phase at 850 degC TiAl6Fe0.5 (#alpha#-phase) and TiAl3.5Fe6.5 (#beta#-phase) were prepared by arc melting and rolling at 850 degC. The mechanical properties of the '#alpha#'- and of the '#beta#'-phase-alloy are compared with the properties of the (#alpha# + #beta#)-alloy TiAl5Fe2.5 in the as rolled and swaged condition and after an additional aging at 550 degC. By this optimizing process it was possible to achieve a tensile strength of Rsub(m) = 1012 N/mm"2, an yield strength of Rsub(p0.2) 954 N/mm"2 and an elongation at fracture A = 14.5% in the TiAl5Fe2.5-alloy, although the degree of hot deformation ...
In this review, the most important inorganic natural gels are presented: opal, aluminosilicate (allophanes) and hydrous iron oxides and silicates. It is demonstrated that natural gels are ordered at the atomic scale. In allophanes, Al is distributed between octahedral and tetrahedral sites. The amount of Al increases as Al/Si ratio decreases. Si-rich allophane have a local structure around Al and Si very different of that is known in kaolinite or halloysite. Transformation of Si-rich allophanes to crystallized minerals implies dissolution-recrystallization processes. On the contrary, in iron silicate with Fe/Si = 0.72, Si and Fe environments are close to those found in nontronite. The gel transformation to Fe-smectite may occur by long range ordering during ageing. In ferric silicate gels, the similarity of local structure around Fe in poorly ordered precursors and what is known in crystallized minerals ...
Mullite long fibres, which are a candidate for high temperature applications were prepared by sol-gel method from water solvent systems. They were synthesized from three different combinations of raw materials as follows: (1):Al(O{sub 1}C{sub 3}H{sub 7}){sub 3}, Al-nitrate and Si(OC{sub 2}H{sub 5}){sub 4} (TEOS), (2):Al metal, Al-chloride and TEOS, (3):Al metal, Al-nitrate and TEOS. In the methods (1) and (2), very fine SiO{sub 2} aerosol particles were also used partially replacing TEOS. The prepared solutions were condensed and examined the spinability by a hand drawing method. Dense and crack free mullite fibres were prepared from the methods (1) and (3) by firing up to 1100 C. Whereas the fibres prepared from the method (2) were less SiO{sub 2} than mullite composition and were porous by the firing due to evaporation of residual Cl ions at high temperature. ...
TiAl with between 0 and 20 volume percent (v%)Ti5Si3 was produced by reactive sintering of cold pressed compacts of elemental Ti, Al and Si powder mixtures at 700C for 15 minutes in vacuum. The results show that adding Si to Ti and Al reduces the swelling associated with reactive sintering of TiAl, as composites containing more than 5 v%Ti5Si3 densified during reactive sintering. However, composites containing more than 10v% Ti5Si3 did not retain their shape during processing, and the TiAl+20v% Ti5Si3 composite completely melted during the sintering process. The formation of pre-reaction liquid phase and the increase in adiabatic flame temperature with simultaneous compound formation resulted in the melting that occurred and the enhanced densification (minimization of swelling) during reactive sintering of the insitu composites.
(Al{sub y}Ga{sub 1{minus}y}){sup 1{minus}x}In{sub x}P semiconductor alloys lattice-matched to GaAs are widely used in visible optoelectronic devices. One of the most recent developments in this area is the AlGaInP-based red vertical cavity surface emitting laser (VCSEL). These lasers, which employ AlGaInP active regions and AlGaAs distributed Bragg reflectors (DBRs), have demonstrated continuous-wave (CW) lasing over the 630--690 nm region of the spectrum. Applications for these lasers include plastic fiber data communications, laser printing and bar code scanning. In this paper, the authors present an overview of recent developments in the processing and performance of AlGaInP based VCSELs. This overview will include a review of the general heterostructure designs that have been employed, as well as the performance of lasers fabricated by both ion implantation and selective ...
Glass-ceramic materials containing 0-60% glass, 0-40% cordierite and 0-40% mullite were developed with dielectric constant lower than of Al{sub 2}O{sub 3} (5.2-6.7). The following glasses were used: SiO{sub 2}, CaO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-SiO{sub 2}, CaO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}, CaO-ZnO-B{sub 2}O{sub 3}, CaO-ZnO-Al{sub 2}O{sub 3}B{sub 2}O{sub 3}, BaO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-SiO{sub 2} and BaO-ZnO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-SiO{sub 2}. The influence of the content of the particular components on the value of dielectric constant of the ceramics was investigated. (author). 9 refs, 3 tabs.
The crystal structure and phonon densities of states (DOS) of #beta#'-SiAlON ceramics, Si_6_-_zAl_zO"zN_8_-_z (0 #<=# z #<=# 4), prepared by a novel slipcast method, are studied by neutron-scattering techniques. The samples with z < 4 form a single-phase solid solution of Si-Al-O-N isostructural to #beta#-Si_3N_4 (space group P6_3/m). A consistent preferential occupation of the 2c sites by oxygen atoms and the 6h sites by nitrogen atoms exists within this structure. The phonon DOS of #beta#'-SiAlON displays phonon bands at #approx#50 and 115 meV. These features are considerably broader than the corresponding ones in #beta#-Si_3N_4 powder.
Research is in progress to obtain a satisfactory creep ductility for alloy 800 when used as heat exchanger material in sodium-cooled fast reactors (LMFBR). The creep test characteristics at present available show that a pronounced tendency to reduced elongation by creep failure may arise after prolonged testing in the 500-700 deg C temperature range. This phenomenon is now agreed to be primarily inherent to the conditions for Ni_3(Ti,Al) precipitation in the material and hence to the Ti and Al concentrations. By structural studies and hardness measurements on material subjected to creep tests and taken from a large number of castings, the relationship was established between the (Ti+Al) content and the structural hardness effect of Ni_3(Ti,Al) at 600 deg C. Below a certain Ti+Al concentration, no precipitation occurs and hence the creep ductility to failure can be improved ...
The broad bands in the room-temperature excitation spectra of Sm"3"+-, Dy"3"+- and Tm"3"+-activated Ca-#alpha#-SiAlON phosphors are interpreted as the N"3"--to-rare earth charge transfer transition (CTT). From the energies of the charge transfer transitions and from the optical data presented for the Eu"2"+ ion, the location of the divalent rare earth ion energy levels relative to the valence and the conduction band of Ca-#alpha#-SiAlON is derived. The salient features of the energy-level diagram are shown to be practical in explaining the temperature-dependent variations of the Eu"2"+ and Yb"2"+ luminescence efficiency in Ca-#alpha#-SiAlON. A comparative study pertaining to the nature of the Yb"2"+ and Eu"2"+ ion luminescence in Ca-#alpha#-SiAlON and in SrSi_2O_2N_2 is presented. A tentative energy-level diagram of the trivalent rare earth ions in Ca-#alpha#-SiAlON is also ...
In order to understand the anodic behaviour of Al--Mo and Al--W amorphous alloys in the borate buffer electrolyte, samples of these alloys were polarized galvanostatically. The resultant anodic films were thicker than the passive films formed during potentiodynamic polarization enabling detailed examination of the films and alloy substrates by surface analytical methods. AES investigations suggest that the anodic films formed at low and moderate voltages on Al--Mo or Al--W amorphous alloys consist of Al-oxide, whereas refractory metals remain unoxidized and enriched at the film/substrate interface. Molybdenum and tungsten act as 'dissolution moderators', restraining the substrate dissolution process at the film/substrate interface. However, after anodization at high voltages (50 V), AES revealed the presence of an oxidized refractory metal in the inner part of the ...
Papers are presented on the development of oxidation- and sulfidation-resistant ferritic alloys; the microstructural stability of sulfidation-resistant FeCrAl stainless steels around 500 C; age hardening in Fe-Mn-Al-C austenitic alloys; the oxidation/corrosion behavior of low-Cr Fe-Cr-Ni alloys containing Zr or Nb; the high temperature oxidation/corrosion of iron-based superalloys; and the role of Mo in the Na/sub 2/SO/sub 4/ induced corrosion of superalloys at high temperature. Topics discussed include the effect of variations of Co content on the cyclic oxidation resistance of selected Ni-base superalloys; high temperature oxidation of Fe based alloys; the morphological development of high temperature oxide scales of Fe-Mn-Al base alloys; and the oxidation of an Fe-Mn-Al-C alloy at 1000 C. Consideration is given to the corrosion properties of Fe-Mn-Al alloys; passive films formed ...
Laser surface alloying with gaseous nitrogen was utilized to improve the wear resistance of a Ti-6Al-4V alloy. Wear-resistant composite coatings reinforced by hard TiN dendrites were produced 'in-situ' on a substrate of a Ti-6Al-4V alloy. The hardness and wear resistance of the laser alloyed coating under two-body abrasive and block-on-ring full-sliding wear conditions were significantly enhanced. (orig.)
Extrusion and subsequent heat treatment of the alloys investigated can lead to reasonable room temperature ductilities and very high strengths being developed compared to the cast + HlPed material. In Ti-45Al-10Nb reasonably room temperature fracture toughness was developed which did not depend on extrusion temperature. For the alloy Ti-48Al-2Cr-0.2C a previously developed solution and ageing heat treatment did not increase the high temperature strength properties when compared to the 'annealed' condition. (orig.)
The A-15 compounds with the highest critical temperatures and critical fields are stable only at high temperatures and sometimes are not stable at any temperature. Fabrication of such materials thus necessarily involves the creation and manipulation of metastable phases. It follows that the bronze matrix technique now under development for Nb_3Sn- and V_3Ga-based composite superconductors is not suitable for high-T/sub c/ materials of the Nb_3 (Al, Ge, Ga, Si) family. Alternative technologies will be necessary for such materials. Efforts to develop suitable alternatives, using Nb_3Al, are described.
X-ray photoemission spectroscopy has been used to measure the valence band offset {Delta}E{sub v} for the AlP/GaP (001) heterojunction interface. The heterojunction samples were prepared by molecular-beam epitaxy. A value of {triangle}E{sub v}=0.43 eV is obtained (staggered band alignment, with AlP valence band below that of GaP). 24 refs., 8 figs., 1 tab.
A local Heine-Abarenkov model potential is proposed for zinc blende-type crystals. The potential parameters are determined by satisfying the zero pressure condition and the first zero of the empirical pseudopotential interpolated from band calculations. Two sets of parameters are presented for thirteen tetrahedral compounds such as AlP, AlAs, AlSb, GaP, GaAs, GaSb, InP, InAs, InSb, ZnS, ZnSe, ZnTe, and CdTe.
The crystal structure and optical reflectivity of AlP has been studied in a diamond anvil cell using energy dispersive x-ray diffraction to 43 GPa and micro-optical reflectance spectroscopy to 36 GPa. AlP undergoes a first order phase transformation from zincblende to a NiAs structure which exhibits metallic reflectivity in the near-infrared. The decrease in volume on transformation is 17%[plus minus]1%. The transformation is reversible but has large hysteresis. The equilibrium transformation pressure is 9.5[plus minus]5 GPa.
This paper describes the performance of AlGaN/GaN HEMTs with 2.4 #mu#m source-drain spacing. So far these are the smallest source-drain spacing AlGaN/GaN HEMTs which have been implemented with a domestic wafer and domestic process. This paper also compares their performance with that of 4 #mu#m source-drain spacing devices. The former exhibit higher drain current, higher gain, and higher efficiency. It is especially significant that the maximum frequency of oscillation noticeably increased. (semiconductor integrated circuits)
LaAlO{sub 3} and CeO{sub 2} films have been successfully grown using sol-gel precursors. LaAlO{sub 3} precursor solution has been prepared from a metal alkoxide route and spun-cast on a SrTiO{sub 3} (100) single crystal to yield an epitaxial film following pyrolysis at 800{degrees}C in a rapid thermal annealer. A CeO{sub 2} precursor solution has been made using both an aqueous and an alkoxide route.
Evaluation of grain boundary composition and structure in superplastically deformed AA5083-based alloys (Al-4.5Mg-1.6Mn-0.2Zr) was carried out in a field-emission gun transmission electron microscope (FEG-TEM). During superplastic deformation at high homologous temperatures materials undergo extensive grain boundary sliding (GBS) which creates a flow of defects in the near-boundary region. Recent literature has shown that the grain-boundary composition in Al-Mg alloys is not necessarily the same as the matrix, and that these differences can have an effect on GBS.
Evaluation of ageable beta alloys Ti-17V-2Fe-2Co-3Al, Ti-17V-7.5Co-3A1 and Ti-8Mo-8V-5Co-3Al continued with room and elevated temperature smooth and notched tensile tests, creep stability, oxidation and stress-corrosion tests. Ti-17V-7.5Co-3Al aged more r...
This article examines problems relating to the calculation of the position of regions of limited solubility of components in the liquid state for four-component systems. An approach based on the use of criterion of stability with respect to diffusion for obtaining equations which describe the region of stratification of the liquid phase in a four-component system is used. The authors used a ES-1020 computer to analyze the critical phenomena in Al-In-P-Sb, Al-Ga-In-P, Al-Ga-In-As, and In-Ga-As-P systems. The position of the spinode in the phase diagram of a four-component system is obtained.
Continuous wave lasing operation with the shortest wavelength for semiconductor lasers was obtained from AlGaInP double heterostructure lasers at 77 K. The structure was grown by metalorganic vapor phase epitaxy. Lasing wavelength was 583.6 nm (yellow). Threshold current was 43 mA (1.9 kA/cm/sup 2/). Magnesium was adopted as a p-type dopant, and was proved to be preferable for a high aluminum composition AlGaInP cladding layer.
Al, Ga and In complexing with methylthymol blue (H_6R) purified by gel filtration is studied. in the case of metal excess complexes with the ratio of components M:H_6R=2:1 with #lambda#=587(Al), 590(Ga) and 593 nm(In) appear. In the case of reacting agent excess complexes with the ratio of component 1:1 with #lambda#_m_a_x=480-490 (Al) and 480 nm(Ga, In) appear. The mechanism of complexing reactions is studied. Molar extinction coefficients and stability constants are calculated.
Highly reliable, practical 0.6 #mu#m-band AlGaInP visible laser diodes (LDs), using a GaInP active layer, are described. Over 10,000 hour stable operation at 50 degrees C has been achieved for 3mW light output. Characteristics for visible LDs with an AlGaInP active layer or a multi-quantum-well active layer are also presented.
partnerships led to the passage of a legislation creating a stormwater authority with Baldwin County, AL. The Coastal Training Program provides up-to-date scientific information...
Low operating power and short cycle life are 2 of the main draw-backs of zinc-air batteries, despite the fact that various attempts have been made to develop improved zinc (Zn) anodes. This study investigated the performance of a Zn anode with a substantial addition of aluminium (Al). Rolled sheets of Zn-Al alloys of varying amounts of Zn and Al were used to prepare the anodes. Results of the study showed that the cells had higher open circuit voltages (OCV) values as well as a higher specific anode capacity. It was observed that specific anode capacity increased with higher current loading. The Zn{sub 59}Al{sub 41} and Zn{sub 67}Al{sub 33} sheets showed the highest performance with high OCV values of between 1540 and 1560 mV, as well as the largest specific anode capacity of 750-800 mAh per g at a discharge current of 200 mA. The 2-phase structure of the Zn-Al ...
Lake Unit AL-05P, for public review and comment. These four CBRS units are located in Baldwin and Mobile Counties, Alabama. We invite the public to review and comment on the draft...
An Fe-19Cr-8Al-0.5Hf alloy has been roll bonded to Alloy 800 to form a protective clad material suitable for use in coal conversion atmospheres. The commercial producibility of both the Fe-19Cr-8Al-0.5Hf alloy and the clad composite has been demonstrated. The clad composite has been shown to exhibit resistance to sulfidation in high sulfur, coal gasification atmospheres low Btu for 2000 hrs at 1800/sup 0/F (1255K). The FeCrAlHf alloy must be preoxidized in the absence of sulfur to form fully protective alumina scales on all surfaces. Useful life of the composite at temperatures of 1400 to 2000/sup 0/F (1033 to 1366K) is governed by reactions at the FeCrAlHf clad alloy 800 interface. The rate of interdiffusion decreases with increasing Ni content and a high Ni alloy such as RA333 appears to be a better substrate than Alloy 800 for a FeCrAlHf composite. The mechanical properties of ...
By means of the light microscopy and by the measurement of the mechanical properties one investigated into the phase composition and the properties of Al-Mg-Ce and Al-Mg-Y system alloys. One plotted the isothermal cross sections of the mentioned systems under 430 and 275 deg C temperatures at up to 16% magnesium concentration and up to 0.7% yttrium concentration. One determined the yield limit and strength, the relative elongation of Al-Mg base hardened and deformed alloys containing 7.0-9.9% Mg and Ce, Y, Mn, Zr dopes upon ageing under 175, 200, 250 and 300 deg C temperatures within the ageing time ensuring the hardening maximum effect
The age hardening behavior of Al-4.5%Cu alloy composite reinforced with zircon sand particulates and produced by stir casting route has been investigated in different quenching media viz, water, oil, and salt brine solution (7wt%). Optical microscopy of the as cast alloy composite indicates that the matrix of the composite has the cellular structure. Copper rich CuAl2 precipitates have been found near particle matrix interface. The results of ageing demonstrate that the microhardness of age hardenable Al-Cu based alloy composites depend on the quenching medium in which they are heat treated. Salt brine quenching is faster as compared to water and oil, even if higher strength is obtained but cannot be used for complex shapes and thin sections where oil quenching is the alternative due to mi...
... by the boron doping in most of the alloys except for Al66Mn9Zr25 + 50 ppm B alloy; permanent deformation at ultimate compressive strength is not ...
... Mirrors (Preprint) Ryan Conk et al. 15 September 2006 ... 4. TITLE AND SUBTITLE Stress Coatings for Large Scale Membrane Mirrors (Preprint) 5a. ...
... Developed from federally funded research, testing and training programs ... al-Qa'ida's closest ally Tehrik-e-Taliban Pakistan's (or TTP's) attempt to ...
This paper summarizes the main features of four current REDD proposals: Compensated Reduction, Papua New Guinea et al; Joint Research Center; and Brazil. ... ...
Nitriding of aluminium 2011 using a radio frequency plasma at higher power levels (500 and 700 W) and lower substrate temperature (500 deg. C) resulted in higher AlN/Al_2O_3 ratios than obtained at 100 W and 575 deg. C. AlN/Al_2O_3 ratios derived from X-ray photoelectron spectroscopic analysis (and corroborated by heavy ion elastic recoil time of flight spectrometry) for treatments preformed at 100 (575 deg. C), 500 (500 deg. C) and 700 W (500 deg. C) were 1.0, 1.5 and 3.3, respectively. Scanning electron microscopy revealed that plasma nitrided surfaces obtained at higher power levels exhibited much finer nodular morphology than obtained at 100 W.
... at compositions below -AlP 4 the films were still unstable, hydrolysing in room air, and the long term stability of higher aluminium phosphides is in ...
... information about, utilized, or discussed these subjects: basic topics: overview materials and material types: ti-6al-4v, ti1100, ti17 , ti6242, imi 550 ...
Porous ?-SiAlON ceramics are synthesized by reaction bonded method using hollow alumina spheres (HASs) as both sintering aids and pore-forming agents. Both micropores and macropores, which are constructured by SiAlON grains with different morphologies, are formed in the final SiAlON samples. The micropores are three-dimentional, and are built by equiaxial grains. While the hollow macropores, which have the similar morphology to hollow alumina sphere, are packed by elongated grains. In the sintering process, the solid dissolution process takes place, giving rise to the different alumina concentration of liquid phase, and thus resulting in the formation of two kinds of grains, the equiaxial grain and the elongated grain.
Homogenous Al{sub x}Ga{sub 1{minus}x}P liquid phase epitaxial layers have been obtained with the temperature difference method under controlled vapor pressure (TDM-CVP). Very clear fine structures near band edge in photoluminescence spectra have been observed at 77 K for the first time. Photoluminescence measurement results confirmed that the free exciton recombination without phonon assistance plays an important role in the luminescence at 77 K and becomes dominant at room temperature. It is considered that Zero-phonon assisted free exciton recombination is intensified by some local perturbations to electrical potentials against carriers or excitons introduced by Al atoms in Al{sub x}Ga{sub 1{minus}x}P layers, which can give momentum change necessary for recombination.
Forster et al. recently showed that weak nonlocality can be amplified by giving the first protocol that distills a class of nonlocal boxes (NLBs) [Phys. Rev. Lett. 102, 120401 (2009)] We first show that their protocol is optimal among all nonadaptive protocols. We next consider adaptive protocols. We show that the depth-2 protocol of Allcock et al. [Phys. Rev. A 80, 062107 (2009)] performs better than previously known adaptive depth-2 protocols for all symmetric NLBs. We present a depth-3 protocol that extends the known region of distillable NLBs. We give examples of NLBs for which each of the Forster et al., the Allcock et al., and our protocols perform best. The understanding we develop is that there is no single optimal protocol for NLB distillation. The choice of which protocol to use depends on the noise parameters for the NLB.
Beta-SiAlON powders have been synthesized using natural clay containing kaolin and quartz by carbothermal reduction and nitridation (CRN), then beta-SiAlON bonded corundum multiphase materials have been sintered using the as prepared powders. The results indicated that both the holding time and sintering temperature are relatively significant in accordance with optimal analysis by orthogonal method. Reaction process can be briefly interpreted by means of X-ray Diffraction and Difference Temperature Analysis as well as phase diagram principle. Bending strength and bulk density were measured in SiAlON in situ bonded corundum materials with doped various sintering agents. Furthermore, the relevant mechanical properties and microstructure were discussed in detail.
... potential propagation in terminal nerve fibers or at the neuromuscular ... means of prosthesis control (Graupe, et al, 1975). ... parallel interface, a joystick ...
... that range from relatively low frequency strong ground motion modeling [Vidale et al., 1985] to high frequency reverse time migration of seismic ...
This paper analyses the role of the translator in the representation of alterity and the construction of national identity, with reference to the work of a nineteenth-century Egyptian translator, essayist and educationalist, Rif?'a R?fi' al-TahT?wi (1801-1874). The essay takhliS al-ibriz fi talkhiS b?ris ("The Extraction of Gold in the Summarizing of Paris") includes numerous examples of constructive translation and representation, which familiarised and legitimised the "other" through the identification of parallels, common values and experience. Al-TahT?wi negotiated between conflicting discourses of modernism and traditionalism, and it is argued that the issues of representation raised in his work are of particular relevance to contemporary concerns in the ...
Zirconia has demonstrated a very moderate toughening effect in nitrogen-based ceramic composites because the reaction between tetragonal zirconia (t-ZrO_2) and nitrogen results in additional zirconia stabilization to a nontransformable t' or cubic structure. In O'-SiAlON matrices, the oxygen concentration increases and the oxygen-rich intergranular glassy phase prevents zirconia from nitridation. As a result, tetragonal ZrO_2 is maintained and is transformable in the O'-SiAlON materials. The present study has provided transmission electron microscopy (TEM) evidence of the zirconia transformation and the associated toughening effect in a ZrO_2/O'-SiAlON composite. The implications and limitations of the transformation on toughening of the material are discussed.
With the assistance of mechanical activation, yttrium-stabilized #alpha#-SiAlON was prepared by combustion synthesis in air, instead of high-pressure N_2 atmosphere for the first time. The reaction activity of metallic particles was remarkably enhanced by mechanical activation, which conduced the reduction of grain size, increased the total surface area and formation of fresh surface. The formation of #alpha#-SiAlON by combustion synthesis in air was explained by a kinetically induced reaction mechanism, in which both initial formation of #alpha#-SiAlON and following avoidance of oxidation were fulfilled by the retardation of O_2 infiltration owing to the short reaction period and fast cooling rate.
Minor addition of B to the Ti-6Al-4V alloy reduces the prior #beta# grain size by more than an order of magnitude. TiB formed in-situ in the process has been noted to decorate the grain boundaries. This microstructural modification influences the mechanical behavior of the Ti-6Al-4V alloy significantly. In this paper, an overview of our current research on tensile properties, fracture toughness as well as notched and un-notched fatigue properties of Ti-6Al-4V-xB with x varying between 0.0 to 0.55 wt.% is presented. A quantitative relationship between the microstructural length scales and the various mechanical properties have been developed. Moreover, the effect of the presence of hard and brittle TiB has also been studied.
Yb-, Y-, Yb/Y-, and Yb/Nd-doped -SiAlON ceramics with 5-wt% barium aluminosilicate (BAS) were synthesized by hot pressing. Typical self-reinforced microstructures were obtained in all investigated -SiAlONs in spite of the type of doped cations. This is attributed to the incorporation of BAS, which could supply suitable liquid phase to promote the anisotropic growth of the -SiAlON grains. All the composites exhibited excellent high-temperature mechanical properties and thermal shock resistance due to the formation of a self-reinforced microstructure and the complete crystallization of BAS additive.
We report the lasing characteristics of gain-guided AlGaInP/AlGaAs visible vertical-cavity surface-emitting laser diodes. At room temperature, continuous-wave operation is achieved over the wavelength range of 657--685 nm with the minimum threshold current at 670 nm. Devices with a 10-[mu]m diameter have threshold currents as low as 1.25 mA at room temperature (297 K) and 0.8 mA at 250 K. In addition, a single predetermined linear polarization state is found, independent of the lasing mode order and operating temperature.
... follows draws on Wittwer (1980b & c), Zinn et al. (1966) and Hess (1968). ... for the Starfish event) and much larger distances along the geomagnetic ...
DZ4 substrates were coated with NiCoCrAlY by plasma spray and subsequently treated by high current pulsed electron beams(HCPEB) of different parameters. The surface microstructure, phase structure and high temperature oxidation resistance were studied. It has been shown that as a result of the HCPEB treatment the loose and rough structure remelted and the surface became smooth. Smooth microregion, craters and cracks appeared on the surface. The ?' phase manifolded and there was no visible thermal stress. The oxidation test at 900 degree C for 100 h showed that a more compact and successive ?-Al_2O_3 scale was formed on the surface of the samples after HCPEB irradiation, which improved the oxidation resistance of the NiCoCrAlY coatings obviously. (authors)
The transmutation of minor actinides in-reactor is one solution currently being studied for the long time management of nuclear waste. In the heterogeneous concept the radionuclides are incorporating in an inert ceramic matrix. The support material must be insensitive to radiation damage. Fission product damage is the main radiation damage source during the transmutation process and therefore it is of the utmost importance to study their effects. We irradiated spinels MgAl_2O_4 (matrix of reference) and ZnAl_2O_4 by fast ions (by example: (86)Kr of approximately 400 MeV) simulating the fission products. Under these conditions, the damage is primarily due to the electronic energy losses (Se). One of the structural features of spinel AB_2O_4 is that the two cations (A(2+) and B(3+)) can exchange their site. This phenomenon is quantified by the inversion parameter. We highlight by XRD in grazing incidence that the structural changes observed in ...
Nd{sub 40}Fe{sub 30}Al{sub 10}Co{sub 15}B{sub 5} alloys were fabricated by high energy ball milling method under various conditions. Microstructure of the alloys was investigated by X-ray diffraction and electron microscopy techniques. Magnetic properties were characterized by hysteresis and thermomagnetic measurements. The high coercive fields up to 2.36 T have been observed on the samples consisting of Nd{sub 2}(Fe,Co,Al){sub 14}B, Nd{sub 6}(Fe,Co,Al){sub 14} and Nd crystallites imbedded in a residual amorphous matrix.
Oberpfaffenhofen, Pedel"al aepublic of Gel1lany. A large number of European scientists have provided ex~eri- ments that will be cooducted in the Material ...
A theoretical study of electron and positron band structures of zinc-blende AlN and InN and their alloy Al_0_._5In_0_._5N is presented using the first-principles full-potential linearized augmented plane-wave method. Equilibrium lattices constants are determined from the total-energy minimization method. The results are compared with previous calculations and with experimental measurement. Electron and positron charge densities are computed as function of position in the unit cell. Detailed plots of distributions are along the direction. The ionicity factors are calculated by means of three different approaches. The calculated results of the positron charge density reflect the high insight for the annihilation effect.
Effects of the addition of precious metals (PM; Pt, Rh) on CeO{sub 2}/Al{sub 2}O{sub 3} and CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} were confirmed to enhance the oxygen storage capacities (OSC). Increments in the OSC of the added CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} catalysts were much greater than those in the OSC of the PM added CeO{sub 2}/Al{sub 2}O{sub 3}. The enhanced OSC is ascribed to the interaction between PM and a CeO{sub 2}-La{sub 2}O{sub 3} solid solution formed during the catalyst preparation. No enhancements in the OSC were observed on physical mixing of CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} and Pt-Rh/Al{sub 2}O{sub 3}, although the composition ratio of PM:CeO{sub 2}:La{sub 2}O{sub 3} is the same as that in the PM added CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3}. This indicates that the intimate ...
... Wright, and Vogel, 1985; Patton, Vogel, Damo- shorter amount of time at the end of the 45-hour kosh, et al., 1989). Lifting strength was signifi- ...
Passivity of aluminum (Al) alloy 3003 in air and in aqueous solutions without and with chloride ions was characterized by electrochemical measurements, including cyclic polarization, electrochemical impedance spectroscopy (EIS), localized EIS and potential of zero charge, Mott-Schottky analysis and secondary ion mass spectroscopy (SIMS) technique. Stability, pitting susceptibility and repassivation ability of Al alloy 3003 under various film-forming conditions were determined. Results demonstrated that passive films formed on 3003 Al alloy in air and in Na2SO4 solution without and with NaCl addition show an n-type semiconductor in nature. The passive film formed in chloride-free solution is most stable, and that formed in chloride-containing solution is most unstable, with the film formed in air in between. Pitting of Al alloy 3003 passivated both in air and in aqueous solutions is inevitable in the ...
The self-consistent-pseudopotential method is applied to the A-15 compounds Nb_3Ge and Nb_3Al. The Fermi energy is found to lie in a region of very flat bands having a bonding character along the Nb chains. Comparison with the band structures of the (nonexistent) A-15 materials Nb_3Nb and Nb_3/sup asterisk/ (chains only) suggest that the p states on the Ge and Al atoms are instrumental in determining the position of the Fermi level. There is little evidence for rigid-band behavior in the Nb_3Al/sub x/Ge/sub 1-x/ system. Studies of the effects of chain dimerization in Nb_3Ge suggest that states at R and M are more likely candidates to participate in structural transitions than states at GAMMA or X.
The thermal stability and deformability of Mn-Al-C alloys containing 0.6 pct C are investigated experimentally as a function of excess phase content. It is shown that an increase in Mn content from 68.9 to 73.5 pct leads to increased stability of the high-temperature epsilon phase. The enrichment of the system Mn-Al-Cu in Mn and Al above the optimum composition leads to the formation of nonmagnetic excess phases, eta and beta, which reduce the magnetization of the alloy. In addition, a decrease in thermal stability is observed in the alloy with 73.5 pct Mn due to the decomposition of the ferromagnetic phase. 7 references.
closure of the BISON network, GOLF and VIRGO will remain the only instruments ...... Faraday Cup solar wind instrument as described in Ipavich et al (1998). ...
Ultrasonic gold and aluminum wire wedge bonding are widely used for electrical and signal interconnections of the integrated circuit chip packages. In this paper, based on the metallurgical theories and thermal aging test methods, the long-term thermal reliabilities of gold and aluminum wire wedge bonding on aluminum and Au/Ni/Cu pads, were investigated, respectively. At 200degreeC, the Au/Al bond interfaces evolved little when the storage time was less than 48h; with the aging time increasing, the interfacial intermetallic compounds (IMC) grew up from the pad (vertical growth); the primary compounds were Au5Al2 near the bond toe and heel, and Au2Al at the periphery. Then, the thickness of IMC was unchanged, and extended horizontally (lateral growth), Au5Al2 transformed into more stable Au...
... than the age of the universe unless it is an unresolved double degenerate or a product of common-envelope binary star evolution (Fontaine et al. ...
To compare the accuracy in the detection and staging of various malignant tumors with high resolution whole-body MRI using parallel imaging with whole-body dual-modality PET-CT. Preliminary results of an interim analysis from a prospective, blinded study are presented, in which 20 patients (mean age 59 years, range 27-77 years) with different oncological diseases underwent whole-body dual modality FDG-PET-CT screening for tumor search or staging in case of confirmed or suspected metastatic disease. All patients also underwent whole-body MRI imaging with the use of parallel imaging (iPAT). High-resolution coronal T1w- and STIR-sequences of 5 body levels with 512 x 512 matrix, axial fast T2w imaging of lung and abdomen (HASTE), contrast-enhanced dynamic and static T1w-sequences of liver, brain, abdomen, and pelvis were performed. Using a 32-channel whole-body MRI scanner (Magnetom Avanto, Siemens Medical Solutions) with a total field of view of 205 cm and free table movement, all ...
In the year 1996 the spheres of competence of several DLR-Institutes working in the areas of fluid dynamics, reaction kinetics, combustion, numerical methods and laser measuring techniques have been brought together while contributing to the internal DLR project 'combustion chamber modelling (BKM)', in order to proceed with the computational simulation of combustion processes in combustion chambers of gas turbines. The main issue was the development of a research code for numerical simulation of fluid flow in real combustion chambers. Here the development of computational models of physical and chemical processes was emphasized, among other processes the formation of soot was treated. Moreover, a worldwide outstanding database of measured data for the purpose of code validation has been created within the framework of the BKM project using the laboratory facilities of the DLR, which are in Germany unique for the experimental investigation of the various processes in ...
Volatile organic compounds (VOC) are an important group of pollutants with adverse effects on humans and the environment. Primary air pollution abatement measures aim at prevention or reduction of pollutant production in industrial production processes, e.g. by improved processes but also by other methods (closed cycle processes, different process materials, etc.). If these measures have been implemented and emissions are still too high, an off-air purification unit must be installed. Biological purification is the method of choice for low pollutant concentrations. Biological purification processes are based on the activity of microorganisms which are capable of biochemical oxidation of organic and some inorganic gaseous compounds into non-polluting or non-odorous compounds. These processes have the advantage that they work at ambient conditions and therefore remove relatively low pollutant concentrations at low investment and operating cost. Lately, biological filters and washers have ...
The establishment of the domestic market in Europe requires rules for the assignment of orders, with which a standardization of the rules of competition can be achieved and with which a discrimination of individual bidders can be prevented. Clients and contractors of power station equipments equally are affected by the definitions for the assignment of orders. The contribution under consideration is a regulation for the procurement of steam turbine systems. It is a supplement of the European standard DIN EN 45510:1998. The regulation integrates the former terms of delivery of association of the electricity industry (VDEW) for steam turbines as well as the collection and evaluation of a multiplicity of experiences of the VGB regulations.
Faserbewehrter Beton wird heute zunehmend auch bei Tunnelbauwerken (Tunnelinnenschalen, Tubbinge) eingesetzt. Wesentliche Vorteile sind das hohe Tragvermogen, das daraus entstehende Einsparungspotential an herkommlicher stabformiger Bewehrung (Biegebewehrung, Bugelbewehrung in der Randzone), die Aufnahme von Spaltzugbeanspruchungen durch die Fasern, Rissbreitenbegrenzung, erhohte Dauerhaftigkeit, verbesserter Brandwiderstand (insbesondere bei Verwendung von Kunststofffasern), Optimierung der Arbeitsablaufe etc. Neue Entwicklungen in der Betontechnologie haben in den letzten Jahrzehnten den faserbewehrten ultrahochfesten Beton (engl. UHPFRC - Ultra High Performance Fibre Reinforced Concrete) hervorgebracht. Im Rahmen dieser Arbeit wird der Einsatz des ultrahochfesten, stahlfaserbewehrten Be...
The economic development of eastern Europe was associated during the last 15 years with the following average annual increases in energy consumption: Approximately 1% in the sectors industry, building and transport, almost 7% in the farming sector, approximately 3% in households, and nearly 4% in the municipal sector. This trend will not continue. As the economic system shifts from centrally planned to free economy and as the previously secluded economy is forced to face world market conditions as well as changed pars of exchange and conditions of payment, it not only experiences a transitory, sharp dip of economic growth in general but, in particular, drastic structural changes. - While there is to be expected, on the whole a slump in national economic growth, in tradiational branches of industry (e.g., metallurgy, the chemicals and textile industry) as well as in farming, such sectors as the service industry and small trade are expanding. (orig./UA).
By tests about pipe failure under extreme bending, moment at cross sections affected by circumferential cracks, admissible strains for securing the integrity in the area of a flow link are indicated. These are 7% for austenic and ferritic materials in the undisturbed cross section. From d/t-ratios of 20 onwards the strains are limited by pipe bulging on the pressure-load side. In this connection, circumferential flaws do not have any influence on the behaviour on the strained side, when their expansion does not exceed the investigated limitis of <60 circumferential expansion and crack depth of 0,3 t. (orig.)
Liberalization and the associated necessity of providing, where possible, inexpensive electrical energy, has intensified still further the demand for higher efficiency steam turbines. Accordingly, continuous efforts are being taken to improve all the flow guiding components of a steam turbine. Special attention is given here to the blading. (orig.) [Deutsch] Die Liberalisierung und die damit verbundene Notwendigkeit, elektrische Energie moeglichst preisguenstig zur Verfuegung zu stellen, hat die Forderung nach hohen Wirkungsgraden von Dampfturbinen weiter verschaerft. Es werden daher kontinuierlich Anstrengungen unternommen, alle stroemungsfuehrenden Teile einer Dampfturbine zu verbessern. Das Hauptaugenmerk gilt dabei der Beschaufelung. (orig.)
After cooling ceilings and source ventilation, simple air conditioning systems like thermal activation of concrete cores are gaining general acceptance. Parallel to this, ground source cooling systems are reducing the need for cold generation. Air conditioning systems of this type are favoured by producers of floor heating systems looking for a new market segment. [German] Nach Kuehldecken und Quellueftung gewinnen jetzt einfach aufgebaute Raumklimaanlagen, wie die thermische Betonkernaktivierung, immer mehr Anhaenger. Parallel dazu werden Verfahren zur Erdkaeltenutzung entwickelt, die den Anteil kuenstlich erzeugter Kaelte weiter zurueckdraengen. Forciert wird diese Art der Klimatisierung insbesondere durch die Hersteller von Fussbodenheizungen, fuer die sich hier ein neues Marktsegment eroeffnet. (orig.)
MPA research activities focus on fracture prevention and on the development of a generally applicable method of component integrity testing which, independent of the safety relevance of the components involved, is also part of ageing management. (orig.) [German] Die Forschungsaktivitaeten an der MPA im Hinblick auf die Erhoehung der Sicherheit und Zuverlaessigkeit komplex beanspruchter Bauteile orientieren sich an den Grundgedanken des Basissicherheitskonzepts (Prinzip des Bruchausschlusses). Zielsetzung war dabei die Entwicklung eines allgemein anwendbaren Nachweisverfahrens zur Komponentenintegritaet, das, abhaengig von der sicherheitstechnischen Relevanz der zu betrachtenden Komponenten, auch Bestandteil des Alterungsmanagements ist. (orig.)
Abstract Plant pathogenic bacteria of the genus Xanthomonas cause a variety of diseases in economically important monocotyledonous and dicotyledonous crop plants worldwide. Successful infection and bacterial multiplication in the host tissue often depend on the virulence factors secreted including adhesins, polysaccharides, LPS and degradative enzymes. One of the key pathogenicity factors is the type III secretion system, which injects effector proteins into the host cell cytosol to manipulate plant cellular processes such as basal defense to the benefit of the pathogen. The coordinated expression of bacterial virulence factors is orchestrated by quorum-sensing pathways, multiple two-component systems and transcriptional regulators such as Clp, Zur, FhrR, HrpX and HpaR. Furthermore, virule...
Calcium sulfate dihydrate which is co-produced in the scrubbing of waste gases from bituminous coal power plants is employed in the underground road securing after recrystallization. Beta-sulfate semi hydrate is obtained from the dihydrate by recrystallisation and it is used as such or as a stiff mixture with additives as a stowing material. Particularly fly ash from coal combustion units, washery refuses and development rocks from coal mining or slags from the metallurgical industry can be used as additives. The compressive and the bending tensile strength of the stowing material can be adjusted by the water content in case beta sulfate semihydrate is used as such.
This process for the preparation of nonaqueous dispersions of water-soluble polymerisates concerns compounds obtained by polymerization of water-soluble unsaturated ethylenic monomers in an emulsion of water in oil. The product is then dewatered to a maximum residual water content of 5% by means of microwaves. The process is azeotropic. The polymer has a molecular weight between 100,000 and 50,000,000, preferably between one and 10 million. Before treating with microwaves, the mixture is concentrated by conventional means until it has a polymer concentration between 20 and 65%, preferably between 40 and 60%. The microwaves have a wavelength between 0.1 and 30 cm. These polymer dispersions can be used in drilling fluids and as additives in tertiary oil recovery. 4 claims.
This is a process for manufacturing a semi-rigid, folding solar generator manufactured from several coated solar cells (Cics), which has at least two folding parts connected together so as to turn by hinges, characterized by the following stages of the process: a) On the back of matrix subsections, in order to cover the connector, carbon fibre strips are glued on, which project over the upper or lower edge of each matrix subsection. b) The projecting ends of adjacent carbon fiber strips are connected with two carbon fibre strips. c) At least two matrix subsections are fixed in separately manufactured carbon fiber frames, and d) the carbon fiber frames, together with the matrix subsections are connected via hinges to a solar generator.
This is a process for producing calcium sulfate dihydrate during desulfurization of stack gases from power station boilers, where the stack gases are introduced into a washing tower and are treated with a washing water suspension containing lime in the washing tower, where oxygen in the form of air or of air enriched in oxygen is also blown into the washing tower, and where the washing water suspension drawn off from the washing tower is fed back to the washing tower at a temperature of 45 to 50/sup 0/C in the circuit and at least part of the flow goes via a thickener and where calcium sulfate dihydrate slurry is drawn off from the thickener.
The dogmatic and constitutional basis as well as points of definition concerning the Technical Code Clean Air (TA Luft) are explained at first, followed by an assessment of the air pollution concentrations within the overall complex of the air pollution abatement measures, and an analyses of air pollution concentrations as a concretization of the state-of-the-art. In connection with the differentiation of the various applicability levels of TA Luft, the inhouse validy for authorities, the importance for law courts and, finally, the external binding effect for plant operators and possible third parties are discussed. At the center of attention are questions concerning validity claims and validity possibilities. (HSCH).
Economic and safe operation of nuclear power plants requires reliable steam turbines with high efficiencies. The progress in flow mechanics achieved over the past few years has allowed the use of powerful methods of flow calculation in developments of new blading with greatly enhanced efficiencies. Thanks to the latest manufacturing techniques, the newly developed blading systems can be produced at low cost. Next to progress in flow mechanics, also the broadbased use of advanced finite-element calculations resulted in a more thorough grasp of the many problems associated with structural mechanics assessment of steam turbine components. The theoretical methods have been supplemented by comprehensive efforts in fracture mechanics and experimental materials studies, thus helping to create a reliable knowledge base which will help to avoid the dreaded stress corrosion cracking phenomenon, in components of steam turbines. The measures introduced to improve operational reliability already in ...
Elektrochemische Potentialmessungen (auch Potentialfeldmessungen) haben sich seit Jahren bewahrt, Bereiche mit aktiver chloridinduzierter Korrosion an tausalzexponierten Bauwerken, wie z. B. Bruckentafeln sowie Zwischendecks und Bodenplatten von Parkhausern und Tiefgaragen nachzuweisen. Bereits 1990 erschien die erste Fassung des Merkblatts B3 der DGZfP. Das DAfStb Heft 422 (1991) - Prufung von Beton Empfehlungen und Hinweise zu DIN 1048 - enthielt die Potentialfeldmessung bzw. das Merkblatt B3 im Anhang. In Deutschland liegen somit zwei Jahrzehnte Erfahrungen mit den entsprechenden Regelwerken und naturlich auch in der praktischen Anwendung vor. In der Praxis zeigte sich jedoch auch, dass die Anwendung verbessert werden muss. Die Potentialmessung wurde vielfach sogar falsch durchgefuhrt, ...
The first part of the study goes into the determination of efficient strategies for the reduction of air pollutants. The developed method is not only derived theoretically but is tested with the concrete example of emissions sources of a German state. The second part goes into the question what the government can do in order to attain that air pollution abatement measures recognized as being efficient will be put into practice. As market economy mechanisms have advantages over central state planning in the allocation of economic resources the question arises if not also for environmental protection market economy tools may contribute to an improvement of the efficiency of air pollution abatement. Therefore the suitability of different tools of environmental policy for the realization of efficient air pollution abatement is investigated and evaluated. This is again not done abstractly but with existing emission sources. (orig./HSCH). 32 figs., 12 tabs.
The program introduced here for determining and describing the multi-axial creep of pipes is based, on the one hand, on the results of the nuclear process heat prototype plant material program and, on the other hand, on the possible load conditions which arise for evaluating accidents or extreme working situations. The basis of a theoretical description of multi-axial creep is the invariant theory in which both the von Mises configuration change hypothesis and the Norton creep law are included. Combined tension and torsion are also considered in detail, the superimposition of cyclic stresses in the tensile threshold area is discussed and cases of partial relaxation are explained. Experimental results for the discussed loads are introduced, which have led to satisfactory agreement between theory and experiment. (orig./MM).
Three different guidelines define the methods to be used for the quantification of exposures due to the incorporation of radionuclides. The adoption of the Euratom-directive into German law requires the adaptation of these guidelines. With this process, the experiences with the practical application of these regulations must be taken into account. (orig.) [Deutsch] Die Ermittlung der Koerperdosis durch inkorporierte Radionuklide ist in drei Richtlinien des Bundesministeriums fuer Umwelt, Naturschutz und Reaktorsicherheit (BMU) geregelt. Die Umsetzung der Euratom-Direktive in deutsches Recht erfordert die Anpassung dieser Richtlinien. Dabei muessen die bisherigen Erfahrungen mit diesen Richtlinien beruecksichtigt werden. (orig.)
This book is mainly a comparison of the cost of pollution with the cost of environmental protection. As to the causes of pollution, a difference is made between pollutants that accumulate and pollutants that do not accumulate. Because of pollutant accumulation it is necessary to carry out both subsequent pollution abatement measures and to take preventive action which helps to avoid pollutant emission. Growth models serve to substantiate why such preventive action is both ecologically and economically useful as a rule. Finally the study makes a comparison between some tools of environmental protection. It stresses in particular that, if a duty on emissions is levied, the polluter has to bear all the cost of the pollution, while at the same time the quality of the environment can be more successfully improved than by emission standards alone.
This conference of Deutsche Wissenschaftliche Gesellschaft fuer Erdoel, Erdgas und Kohle focused on energetic utilisation and recycling of waste materials and biomass, i.e. combustion, gasification and pyrolysis. Aspects of process control were gone into as well. [German] Die Fachbereichstagung der Deutschen Wissenschaftlichen Gesellschaft fuer Erdoel, Erdgas und Kohle beschaeftigte sich mit der energetischen und stofflichen Nutzung von Abfall und Biomasse. Verbrennung, Vergasung und Pyrolyse verschiedener Abfallstoffe sowie die Prozesssteuerung wurden eroertert.
This comprehensive final report for the Swiss Federal Office of Energy (SFOE) examines ways to optimise energy flows in mains networks that include distributed generation facilities. Increasing use of decentralised generation, its effects on the operation of low-voltage mains and the efficient use of the 400 V mains is discussed. The principles of operation and construction of controlled storage installations are discussed and concrete examples of their use in both grid-connected and island operation are quoted. Alternatives to storage are looked at from both the technical and economic points of view. The storage technologies used such as flywheels, supercaps, redox-flow batteries and lead-acid accumulators are briefly assessed and the results of simulations are discussed.
The research project aimed at the selection or development of wear-reducing measures for submerged components of hydroelectric power plants. This comprised the optimisation of hydraulic profiles as well as materials testing for abrasion and cavitation. Another field of research was the development of appropriate application processes. (orig.) [German] Das Hauptziel des Forschungsvorhabens bestand in der Auswahl bzw. Entwicklung geeigneter Schutzmassnahmen zur Verschleissminderung an wasserberuehrten Komponenten von Wasserkraftanlagen. Diesem Ziel untergeordnet waren neben der Optimierung hydraulischer Profile auch Materialuntersuchungen hinsichtlich Verschleissbestaendigkeit gegenueber Abrasion und Kavitation. Ebenso war die Entwicklung geeigneter Applikationsprozesse ein wichtiger Bestandteil der Aufgabenstellung. (orig.)
On 10 dialysis patients we performed 12 balloon dilatations, 2 catheter lyses, 6 stent implants (Palmaz stent) and one atherectomy of central venous stenoses or occlusions (v. subclavia, v. brachiocephalica) at the shunt arm of the patient. The primary success rate was, in balloon PTA and lysis, 12/14 interventions, and in stent placement and atherectomy 7/7. The angiographical and clinical primary result after stent implantation was significantly better than after conventional dilatation. After 66% of the balloon dilatations recidivation occurred within the first year; this can be treated by means of repeated PTA. Whether long-term exclusion of recurrence can be achieved by stent implantation, must be established by means of follow-up studies that are at present in progress. (orig.).
Trapezblechstege im Bruckenbau kommen trotz der groen Vorteile, die diese Bauweise bietet, in Deutschland bisher nur an einem Pilotprojekt zur Anwendung. Durch die charakteristischen Eigenschaften des Trapezbleches entstehen konstruktive und wirtschaftliche Vorteile gegenuber herkommlichen Bruckenbauweisen. Allerdings lassen die aktuell gultigen Regelwerke aufgrund fehlender Kenntnis zum Tragverhalten und mangelnder Erfahrung keine wirtschaftliche Ausbildung zu. Dies zeigt sich am Beispiel des Pilotprojekts. Die Ausbildung der Verbundfuge wurde hier nur sehr unbefriedigend gelost und verdeutlicht somit die Notwendigkeit einfacher und praktikabler Verbindungsmoglichkeiten. Am Institut fur Leichtbau Entwerfen und Konstruieren der Universitat Stuttgart wurde in Zusammenarbeit mit dem Institut...
The high temperature abrasive wear resistant of the composites with different Al{sub 2}O{sub 3} volume fractions, particle coating and size were investigated and the failure action of composites under different conditions at high temperature was analyzed. The results showed that the high temperature abrasive wear resistant of composite with Ni coating and wide size and 39% volume fraction of particle is the best among all composites examined. (orig.)
The wavelength dependence of the threshold in an InGaP-InAlGaP vertical cavity surface emitting laser is investigated using a microscopic theory of the semiconductor gain medium. Good agreement is found between experiment and theory for the minimum threshold lasing wavelength for a range of laser structures.
The wavelength dependence of the threshold in an InGaP-InAlGaP vertical cavity surface emitting laser is investigated using a microscopic theory of the semiconductor gain medium. Good agreement is found between experiment and theory for the minimum threshold lasing wavelength for a range of laser structures.
The present report concerns a research for the tritium and for the carbon 14 in lichens in a spirit of bio-indication: the first results appear in Daillant and al (2004 ) and additional results were presented to the congress B.I.O.M.A.P. in Slovenia, organized collectively by the institute Josef Stefan from Ljubljana and the international atomic energy agency from Vienna (Daillant and al 2003). (N.C.)
Superconducting thin film particle detectors can be very attractive due to the low sensitivity to radiation damage. We describe the fabrication procedure and the characterization of Nb/Al bilayers as particle detectors. First steady and dynamical results are reported from tests of 5 MeV alpha-particle detection.
Eu-#alpha#-SiAlON (Eu_m_/_2Si_1_2_-_m_-_nAl_m_+_nO_nN_1_6_-_n) was synthesized with nominal compositions having small m and n values, by firing the powder mixture of Eu_2Si_5N_8, #alpha#-Si_3N_4, AlN, and Al_2O_3 at 1900 "oC for 6 h under 1 MPa nitrogen atmosphere. The ratio of the oxidation state of Eu"2"+/Eu"3"+ was estimated from the X-ray absorption fine structure (XAFS) measurement. The observed X-ray absorption near edge spectrum (XANES) showed that the Eu ion in Eu-#alpha#-SiAlON was mainly in divalent state but also coexisted with a small amount of Eu in the trivalent state. The crystal structure of Eu-#alpha#-SiAlON was refined by the Rietveld analysis of the X-ray powder diffraction patterns. The lattice constants of the samples increased with increasing m and n values. The excitation band of Eu-#alpha#-SiAlON ranged from the ...
The alloy of Ti-Al-Mo-V-Cr system is studied for its structure in a strained state and specific features of #beta#-#alpha# transformation in a #beta#-matrix and deformation twins on ageing. It is determined that preliminary deformation initiates the decomposition of solid solution on aging. In a metastable #beta#-titanium alloy the substructure of deformation twins is shown to vary essentially with aluminium and chromium partial substitution for molybdenum and vanadium
The optimum of strontium amount for good modification of AK7, AK9, AK11, AK52, AK104 alloys was determined on the base of the analysis of microstructural changes. The stability of the modifier was investigated on the way of successive remelting of billets. The influence of amount of modifier on the impact strength of the alloys was established. (author)
The formation of #alpha#'-sialon using Li as a modifying cation was investigated. The effects of the Li content, firing temperatures and Si/Al ratios on #alpha#'- yield were studied. The results indicated that at lower sintering temperatures the stabilisation of #alpha#'-sialons was obtained but the high weight losses of Li at higher temperatures limited the stabilisation. Increased ''Al'' content in the compositions resulted in an increase in the stability of Li-#alpha#'-sialon at higher temperatures, by the formation of a liquid phase which retains Li in the system. (orig.).
High purity MgAl{sub 2}O{sub 4} spinel specimens irradiated in FFTF-MOTA to very high exposure have been examined by three techniques to determine changes in their optical properties. Significant changes were observed in optical absorption, photoluminescence and radioluminescence.
Lithium tetrachloroaluminate solutions in thionylchloride, methylacetate and their mixtures are studied by "7Li and "2"7Al NMR. It is found that introduction of methylacetate in the LiAlCl_4-SOCl_2 system results in a change of lithium tetrachloroaluminate formation constant. In the ternary system, Li"+ is solvated by methyl-acetate after complete destruction of tetrachloroaluminate anion. Refs. 9, figs. 2.
Using the full potential linearized augmented plane wave (FLAPW) method, the magnetic properties of two-dimensional Ru and Rh monolayers (MLs) on a NiAl(001) surface have been investigated. It has been found that free standing one monolayer Ru and Rh films have ferromagnetic ground state with magnetic moments of 2.21 and 1.48 #mu#_B, respectively. The ferromagnetism is still observed even on a Ni terminated NiAl(001) surface, while no magnetic state is found on an Al terminated surface. The calculated magnetic moments of Ru and Rh atoms are 1.56 and 0.88 #mu#_B, respectively. In addition, an induced magnetic moment in surface Ni is observed. It has been found that the free standing Ru film has perpendicular magnetization to the film surface with a magnetocrystalline anisotropy (MCA) energy of 0.66 meV/atom, while an in-plane MCA energy of 0.37 meV/atom is achieved in Rh film. Very interestingly, we find that both ...
In this paper, aluminium nitride synthesis is carried out by direct laser irradiation onto an aluminium target surface in a nitrogen containing atmosphere. The influence of various processing parameters on the microstructure of AlN thin films is investigated in order to improve their tribological properties. The main microstructural characteristics: nature, concentration, in depth distribution and morphology of various phases are studied versus processing parameters by TEM and GIXD. (author). 2 refs., 1 fig., 2 photos.
In this paper, aluminium nitride synthesis is carried out by direct laser irradiation onto an aluminium target surface in a nitrogen containing atmosphere. The influence of various processing parameters on the microstructure of AlN thin films is investigated in order to improve their tribological properties. The main microstructural characteristics: nature, concentration, in depth distribution and morphology of various phases are studied versus processing parameters by TEM and GIXD. (author). 2 refs., 1 fig., 2 photos.
In the present work, electrochemical measurements and corrosion tests in NaCl solutions were carried out to study the effect of aging treatments on pitting corrosion behavior in a 8090 alloy and its high purity Al-Li binary alloy analogue. The pitting corrosion characteristics and corrosion resistance of the 8090 alloy have been determined in relation to precipitation microstructures. (orig.).
Trace elements have been determined in biological samples including pepperwort, thyme, plantain, blessed thistle and common comfrey as well as cabbage leaves and milk powder. Concentrations of Al, Si, and Cl have been determined by fast neutron activation analysis while, in the case of Mg-, K, and Cl the X-ray fluorescence method was used.
In a suicide committed using aluminium phosphide (AlP) the liberated toxic phosphine gas was detected in post-mortem specimens using a headspace gas chromatographic procedure with a nitrogen-phosphorous detector (HS-GC/NPD). At autopsy a direct sampling into airtight headspace vials for a later analysis is recommended. AlP has to be considered a potent pesticide and its use and availability should be restricted as much as possible.
The structural parameters of various Haegg phases (H or M_n_+_1AX_n phases) are studied experimentally by x-ray and electron spectroscopies, x-ray diffraction, and ab initio full potential as well as full mutiple scattering theoretical calculations. Experimentally it was found that the structure of all ternary compounds analyzed herein are relaxed. The values of the lattice parameters and relaxations obtained from ab initio calculations are in excellent agreement with those deduced from the analysis of the experimental data. The bonding scheme has been analyzed and the charge transfer between constituting atoms determined. It is demonstrated that the strength and electrical transport properties in these materials are principally governed by the metallic planes. For the solid solution (Ti_0_._5Nb_0_._5)_2AlC, the most salient result is that the basal planes are corrugated, which could explain the solid solution scattering observed in this H phase.
The Ti-6Al-4V alloy was treated by inductively coupled rf plasma nitriding. The effects of plasma-processing time in the range of 5-35 min on the microstructure and the mechanical properties of the plasma-nitrided Ti-6Al-4V samples were studied. The plasma power input was adjusted at 450 W and pure N{sub 2} gas was introduced to establish a treatment pressure of 8.0-8.4 x 10{sup -2} mbar. The characteristics of the nitrided layers have been investigated by microhardness testing, surface roughness measurements, optical microscopy, and x-ray diffraction. The results show that the surface microhardness increases as the plasma-processing time increases to reach 2000 HV0.1 at a plasma-processing time of 35 min. A high nitriding rate of 2.81 {mu}m{sup 2} s{sup -1} at a plasma-processing time of 25 min was achieved. The formation of the hard phases TiN, Ti{sub 2}N, and Ti(N) in the Ti-6Al-4V surfaces are found to be the reason for ...
The Ti-6Al-4V alloy was treated by inductively coupled rf plasma nitriding. The effects of plasma-processing time in the range of 5-35 min on the microstructure and the mechanical properties of the plasma-nitrided Ti-6Al-4V samples were studied. The plasma power input was adjusted at 450 W and pure N_2 gas was introduced to establish a treatment pressure of 8.0-8.4 x 10"-"2 mbar. The characteristics of the nitrided layers have been investigated by microhardness testing, surface roughness measurements, optical microscopy, and x-ray diffraction. The results show that the surface microhardness increases as the plasma-processing time increases to reach 2000 HV0.1 at a plasma-processing time of 35 min. A high nitriding rate of 2.81 #mu#m"2 s"-"1 at a plasma-processing time of 25 min was achieved. The formation of the hard phases TiN, Ti_2N, and Ti(N) in the Ti-6Al-4V surfaces are found to be the reason for the increased ...
Continuous-wave (cw) operation at temperatures up to 23 /sup 0/C of an Al/sub 0.26/Ga/sub 0.26/In/sub 0.48/P/Ga/sub 0.52/In/sub 0.48/P/ Al/sub 0.26/Ga/sub 0.26/In/sub 0.48/P double heterostructure (DH) laser has been achieved for the first time. The threshold current was 160 mA at 20 /sup 0/C for a device with a 10-..mu..m-wide and 250-..mu..m-long ion-implanted stripe geometry. The emission wavelength was 671 nm during cw operation at 10 /sup 0/C. To reduce thermal resistance to a heat sink, a dually stacked structure made of a thin (approx.0.3 ..mu..m) p-AlGaInP layer and a p-Al/sub 0.76/Ga/sub 0.24/As layer was used as a cladding layer. The DH wafer was grown by atmospheric pressure metalorganic chemical vapor deposition.
Powders with nominal compositions (in atomic percent) Ti-48Al and Ti-48Al-2Nb-2Cr were prepared by the plasma rotating electrode process (PREP) and gas atomization (GA) techniques. As-solidified and heat-treated (1000degC per 3 h) powder samples were examined by metallography, scanning electron microscopy, X-ray diffraction and transmission electron microscopy. The microstructures of the powders were characterized as a function of atomization technique, alloy content, powder particle size (solidification rate) and thermal history. All of the as-solidified powders were comprised of disordered [alpha], and ordered [alpha][sub 2]-Ti[sub 3]Al and [gamma]-TiAl. For both alloys, a larger volume fraction of [alpha] and [alpha][sub 2] was observed in the PREP powders relative to GA powders of comparable size. Additionally, for both alloys and both atomization techniques, the volume fraction of [alpha][sub 2] ...
There is an increasing number of applications for hard coatings in engineering where the properties of the single-layer coating are not sufficient. One way to solve this problem is to use a multilayer coating that combines the properties of several coating materials. In this study, TiN-CrAlN and CrN-CrAlN multilayer coatings were deposited on 100Cr6 and S6-5-2 (DIN) steel substrates, by means of unbalanced magnetron sputtering. For comparison, TiN, CrN and CrAlN single-layer coatings were also prepared. For all depositions the coating temperature was below 473 K. Indentation testing, hardness measurements and scratch tests were performed to characterize the mechanical properties. The correlation between the wear behavior in rolling contact and the mechanical properties of the multilayer coatings is reported. A ball crater preparation technique through scratch tests and wear tracks was used to observe the deformation and ...
Distributed Bragg reflectors (DBRs) composed of In_0_._5Al_0_._5P/In_0_._5(Al_yGa_1_-_y)_0_._5P quarter-wave layers have been prepared using metalorganic vapor phase epitaxy. The structures were grown over a wide range of high-index layer composition (0#<=#y#<=#0.6) and peak reflectivity wavelength (720 nm#<=##lambda##<=#565 nm, covering the spectrum from deep red to green). In all cases observed and calculated reflectance spectra were in excellent agreement. Using these DBRs, an undoped all-phosphide visible vertical cavity surface-emitting laser structure was grown. Under pulsed optical excitation at room temperature, lasing was obtained at a wavelength of #lambda##approx#670 nm, with a threshold power density comparable to that observed from similar structures prepared using AlAs/AlGaAs DBRs.
MoSi_2-particulate-reinforced #alpha#-SiAlON ceramic composites 10, 20, 25, and 30 vol% were prepared by at 1,750--1,800C. The #alpha#-SiAlON matrix was of the composition (Y_0_._4_8Si_1_0_._0_0Al_2_._3_0O_1_._1_7N_1_5_._2_9). The hardness for the fully dense samples changed from HV10 = 22.5 to 15.3 GPa and the toughness from 3.2 to around 5.2 MPa#centre dot#m"1"/"2 when up to 30 vol% MoSi_2 was present. Two interesting microstructural features have been found. First, with an increasing amount of MoSi_2 a pronounced coalescence of MoSi_2 particles formed a ''dual phase'' material. The second effect was the growth of elongated #alpha#-SiAlON grains in the matrix with 10 vol% MoSi_2 added. The oxidation resistance has been determined, to be unaffected by the addition of 20 vol% MoSi_2 at 1,250 C in oxygen gas of 1 atm pressure.
Pressureless-sintered AlN and hot-pressed, pressureless-sintered and reaction-bonded SiC were neutron irradiated at temperatures between 100 and 785degC up to a fluence of 5.2 x 10"2"4 n/m"2. The hardness was increased by up to 51% in AlN and 84% in SiC. The hardness decreased after annealing at temperatures around the irradiation temperature. At the same temperatures, the macroscopic length, which was increased by irradiation, also began to decrease. The hardness and length were almost recovered after 1,200 #approx# 1,400degC annealing. Thus, hardening in irradiated AlN and SiC is controlled by the number of point defects, or, more precisely, by the strain caused by small point defect clusters which pin down dislocation movement. Dislocation loops were still observed in some samples after 1,400degC annealing while the hardness was almost recovered to that in the unirradiated state. Thus, the existence of dislocation loops ...
A Fe-20at.%Cr-10%Al matrix was dispersed with a wide range of different oxides in order to study the effect of oxygen-active dopants on the high-temperature growth and adhesion of {alpha}-Al{sub 2}O{sub 3} scales. Effect of these various cation dopants on the alumina scale microstructure was correlated with dopant ion segregation to the {alpha}-Al{sub 2}O{sub 3} grain boundaries using analytical electron microscopy. Elements such as Mn and V showed little effect on the oxide scale and were not observed to segregate. Elements such as Y and Gd resulted in finer, more columnar {alpha}-Al{sub 2}O{sub 3} grains and were segregated to scale grain boundaries. However, Ti, Ta, Ca, and Nb also were found to segregate but had a lesser effect on scale morphology. This indicates that cation segregation to scale grain boundaries is not a sufficient condition to achieve beneficial oxidation effects. The driving force ...
In case of airplane engine, technical development like increase of temperature at the turbine entrance or high speed rotation with a purpose of thrust up, and reduction of structural part single substance mass or reduction of number of parts in order to achieve lightness and so forth, has been promoted in order to improve the performance that is evaluated by thrust weight ratio (thrust/weight). Accordingly, research and development of high heat resistance, high strength, lightness and so forth of each material of the parts are in demand. As a representative material corresponding to such demand, L10 type {nu}-TiAl intermetallic compound which is light and has improved high temperature strength properties is paid attention and its development is promotes. The authors were successful for the first time in the world to manufacture composite material with CVD type SiC fiber that was difficult so far by using TiAl-Cr alloy having super plasticity at ...
SiAlONs are ceramics with high potential as biomaterials due to their chemical stability, associated with suitable mechanical properties, such as high fracture toughness and fracture resistance. The objective of this work was to investigate the mechanical properties and the cytotoxicity of these ceramic materials. Three different compositions were prepared, using silicon nitride, aluminum nitride and a rare earth oxide mixture as starting powders, yielding Si_3N_4-SiAlON composites or pure SiAlON ceramics, after hot-pressing at 1750 deg. C, for 30 min. The sintered samples were characterized by X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM). Furthermore, hardness and fracture toughness were determined using the Vicker's indentation method. The biological compatibility was evaluated by in vitro cytotoxicity tests. Ceramic with elevated hardness, ranging between 17 and 21 GPa, and high fracture ...
Red mud (Rm) is the main by-product of the Bayer process for alumina extraction from bauxite, and grey slurries (GS) are generated during the granite rocks transformation processes. the huge volume of those wastes generated every year suppose a serious environmental problem. Recent works by our group demonstrate the efficiency of both types of muds as corrosion inhibitors for iron and steel in alkaline media containing chlorides. The elemental analysis of these slurried shows that Al{sup 3}+ is the main common element. Therefore, the aim of this paper is to study the effect of the soluble Al{sup 3}+ in the electrochemical behaviour of iron in alkaline media, in presence and absence of chlorides. The electrochemical study using Cyclic Voltammetry (CV) and Electrochemical Impedance Spectroscopy (EIS) together with surface analysis techniques allowed to conclude that Al{sup 3}+ blocks the surface of steel in alkaline media ...
A variety of investigations have demonstrated commonalities between the Baldwin (1977) Effect, the blueshifting of CIV emission lines (e.g., Gaskell 1982; Richards et al. 2002), and the L_UV-L_X relationship (e.g., Avni & Tananbaum 1982; Strateva et al. 2005; Steffen et al. 2006); indeed all three of these observational effects may be manifestations of the same underlying (but still uncertain) physics. This commonality is of interest to investigations of accretion disk winds (e.g., Murray et al. 1995; Proga et al. 2000) from active galactic nuclei (AGN) as there is evidence that broad absorption line quasars (BALQSOs) are drawn from a parent sample of quasars that exhibit larger than average CIV blueshifts, weaker than average CIV emission line strengths, and bluer than average (intrinsic) colors. The properties of the absorption troughs appear to be dependent upon these ...
Room-temperature pulsed laser operation of (Al/sub 0.55/Ga/sub 0.45/)/sub 0.5/In/sub 0.5/P /(Al/sub 0.17/Ga/sub 0.83/)/sub 0.5/In/sub 0.5/P / (Al/sub 0.55/Ga/sub 0.45/)/sub 0.5/In/sub 0.5/P double heterostructure laser diodes grown by metalorganic chemical vapor deposition has been achieved. The lasing wavelength is 626.2 nm, which is the shortest ever reported for an AlGaInP double heterostructure laser. Threshold current density is 50 kA/cm/sup 2/ for a diode with a 20-..mu..m-wide and 200-..mu..m-long stripe.
This 7th edition reveals the progress in steam engineering and the great future potential of steam engineering applications. Pollution abatement and design experiences gained during the operation of existing plants, and experiences gained in waste incineration are of environmental relevance. Recent materials developments and knowledge, e.g. as regards pipes and fittings, have been making significant contributions to supercritical-steam efficiency improvements. Emphasis is also placed on automation, control engineering, water chemistry etc., and on regulations, licensing procedures, and the training of the staff of plants. (orig./KOW) [Deutsch] Die nunmehr vorliegende 7. Ausgabe zeigt den Fortschritt und das zukuenftig noch erhebliche Potential dieser Technik auf. Erfahrungen mit den nun schon seit Jahren laufenden Anlagen zur Schadstoffminderung, Konstruktion und Auslegung sowie Betriebserfahrungen zur thermischen Abfallverwertung sind ...
The regenerator of Stirling cycle machines has an relatively unknown potential for thermal shorting, because the thermal flow path within the solid of a randomly stacked wire mesh, which is defined by its 'connectivity', is unknown. Earlier publications have shown two principles of experimental techniques to quantify connectivity. One quantifies connectivity as a function of axial pressure using the electric current analogy, the other measures connectivity via the temperature gradients along a regenerator and a series-connected reference body of known conductivity. Both papers offer preliminary results of reduced usefulness related to the testing method or setup. This contribution describes a new setup and its technique, which results from the practical knowledge and experience of the first two attempts, and aims for an improved determination of connectivity of the original representative Stirling regenerators with and without housing. Please contact the author for ...
For location of leakage at district heating pipelines several techniques are available today. If there is no wire bound lead monitoring system installed, the DH company has to apply mobile methods for detection and location and if possible characterization of leakage. Most mobile methods available today are restricted in application and often they cause supply disconnections, especially the location of very small leaks is difficult. The Institute for Environmental, Safety and Energy Technology (UMSICHT) has tested a new developed method that can be executed by own employees of DH companies that can be realised parallel to normal supply mode, and that is able to locate and characterize even very small leakages. (orig.) [Deutsch] Zur Lecksuche an Fernwaermeleitungen stehen verschiedene Techniken zur Verfuegung. Wurde beim Bau der Fernwaermetrasse kein drahtgebundenes Ueberwachungssystem eingebaut, ist der Netzbetreiber auf mobile Lecksuchmethoden ...
Since enterprises operating offices and facilities at geographically distributed sites have been establishing an intranet for inter-office communication at the management level, the idea of integrating another intranet for multi-site technological facility management comes naturally. The Aachen-based technology enterprise Eurem for this purpose developed a Network and Security concept with solutions that can be customized for linking a variety of computerized control and monitoring systems. The package includes a modular substation named modUS, which is open to the field side as well as to the management side, is capable of efficiently and reliably performing the facility management functions by way of remote controlling via intranets. (orig./CB) [Deutsch] Nachdem in den Unternehmen mit verteilten Liegenschaften die unterschiedlichsten Buerokommunikationssysteme ueber eigene Netzwerke verbunden werden, liegt es nahe, auch verteilte Gebaeudeautomationssysteme in diese Vernetzung ...
In view of current trends in motor car development, the author investigates the increasing conflict between higher comfort and lower fuel consumption. The conflict results mainly from insufficient cooling water heating with consumption-optimized engines. So far, it was never necessary to analyze heat flow after cold starting and heat-up of the powertrain, to develop strategies for heat storage and distribution, to remove heat sinks and to use components multifunctionally. The contribution shows that a general heat management strategy for the whole vehicle will result in high potential fuel savings and improved thermal comfort. Using the example of a latent heat store, heating strategies for the engine and transmission system on the one hand and the passenger compartment on the other hand are developed, and the advantages are presented in detail. [German] Abgeleitet aus den Trends in der Fahrzeugentwicklung wird auf den immer staerker werdenden Konflikt zwischen den steigenden ...
The fibre reinforcement of ceramic materials is used above all to improve the toughness and tolerance of damage, compared to unreinforced monolithic ceramics. This improvement is made possibly by the bridging effect of the cracks by the fibres in crack propagation in the matrix. In this work, the crack bridging effect of the fibres is included in a bridge stress equation, in which a clear relationship between bridge stress and crack opening is determined. The most important step for deriving the bridge stress law was determining the probability of failure of a fibre for a given axial stress curve. One relied on the micromechanical analysis of Hutchinson and Jensen here, by which the boundary conditions in multi-fibre materials can be included and realistic assumptions can be made for the load transfer mechanisms in the fibre/matrix boundary surface. (orig./MM) [Deutsch] Die Faserverstaerkung keramischer Werkstoffe dient vor allem zur Verbesserung der Zaehigkeit und ...
This report presents the results of the BMBF-sponsored project Fundamentals and models for assessing the effect of climate changes on soil, plant development and the crops of an economically significant range of farm products. Its aim was to study, by means of the results obtained for winter wheat, the dependence of plant growth on temperature, radiation and water as well as nutrient supply for other economically important crop types. Building on this, process-oriented, climate-sensitive agricultural ecosystem models for winter rye, winter barley, sugar-beet and winter intercrops were developed, verified and, in some sites, validated. First scenario calculations served to demonstrate the climate sensitivity of these models. (orig./KW) [Deutsch] Im vorliegenden Bericht werden die Ergebnisse des BMBF - Vorhabens `Grundlagen und Modelle zur Abschaetzung von Klimaaenderungen auf den Boden, die Pflanzenentwicklung sowie den verwertbaren Ernteertrag einer wirtschaftlich ...
PVD-coatings based on TiB{sub 2} are expected to show high wear resistance and low tendency of adhesion on metal forming tools. Coating adhesion and morphology can be modified over a wide range by varying the content of nitrogen (N{sub 2}) and the deposition parameters power and bias voltage. All coatings were deposited using commercial unbalanced magnetron equipment, the deposition was homogeneous in a volume of 400 x 400 x 400 mm{sup 3}. Hipped and hot pressed TiB{sub 2}-targets were used, nitrogen (N{sub 2}) was added as gas, Ti and Al by a solid Ti-Al-target. The tribological behaviour was tested by a pin-on-disc wear test. The coatings investigated were TiB{sub 2}, TiAlB(N), TiAl(N) and TiB{sub 2}/TiAl(N). As counterpart in the pin-on-disc wear test, 6 mm diameter spheres of steel (100Cr6), aluminium, brass and bronze were used. The experiments showed a non-uniform wear ...
The efficiency of two thin-film diffusion barriers to be used in silicide/aluminum metallization schemes for silicon integrated circuits were evaluated. Control samples of Si/CoSi{sub 2}/Al and Si/Pd{sub 2}Si/Al, and test samples of Si/CoSi{sub 2}/Ta{sub 2}N/Al, Si/CoSi{sub 2}/W/Al and Si/Pd{sub 2}Si/Ta{sub 2}N/Al were used for sheet resistance, X-ray diffraction, Rutherford backscattering, and Auger-electron spectroscopic measurements. TEM studies were carried out on representative samples to examine the nature of the interfaces. Results from the analytical tests indicated that all three types of test samples are resistant to gross diffusion and intermixing of Co, Pd, Al and Si. They also showed that in the control samples, annealing causes interdiffusion of these species, necessitating the presence of a diffusion barrier. For test contacts, results ...
Two families of CeO{sub 2}/Al{sub 2}O{sub 3} (ACE) catalyst supports, containing 3 and 20 % wt CeO{sub 2} respectively, have been examined and compared with the pure oxides CeO{sub 2} and (transition-phase) Al{sub 2}O{sub 3}. Structural data indicate that, also in the presence of CeO{sub 2}, the Al{sub 2}O{sub 3} support undergoes all phase transitions at the usual temperatures. Electron micrographs show that particles morphology and crystals size are mainly imposed by the Al{sub 2}O{sub 3} support. The porosimetric texture indicates a more pronounced meso-porosity in the ACE systems than in pure Al{sub 2}O{sub 3}, especially in the case of low CeO{sub 2} loadings. FTIR spectra and volumetric/calorimetric data of the adsorption of CO at {approx}300 K show that the surface Lewis acidity of aluminas is severely modified by the presence of CeO{sub 2}: the overall CO uptake is ...
By using a model dielectric matrix in electron self-energy evaluations the computational effort of a quasiparticle band-structure calculation for a semiconductor is greatly reduced. Applications to various systems with or without inversion symmetry, having narrow or wide band gaps, and semiconductor alloys demonstrate the reliability and accuracy of the method. Calculations have been performed for thirteen semiconducting or insulating materials: Si, LiCl, AlP, AlAs, AlSb, GaP, GaAs, GaSb, InP, InAs, InSb, and the Al{sub 0.5}Ga{sub 0.5}As and In{sub 0.53}Ga{sub 0.47}As alloys. Excellent agreement with experimental results is obtained for the quasiparticle energies for these materials. The only three exceptions, {ital E}({Gamma}{sub 1{ital c}}) of AlP, {ital E}({ital L}{sub 1{ital c}}) of AlAs, and {ital E}({ital L}{sub 1{ital c}}) of AlSb are ...
By using a model dielectric matrix in electron self-energy evaluations the computational effort of a quasiparticle band-structure calculation for a semiconductor is greatly reduced. Applications to various systems with or without inversion symmetry, having narrow or wide band gaps, and semiconductor alloys demonstrate the reliability and accuracy of the method. Calculations have been performed for thirteen semiconducting or insulating materials: Si, LiCl, AlP, AlAs, AlSb, GaP, GaAs, GaSb, InP, InAs, InSb, and the Al_0_._5Ga_0_._5As and In_0_._5_3Ga_0_._4_7As alloys. Excellent agreement with experimental results is obtained for the quasiparticle energies for these materials. The only three exceptions, E(#GAMMA#_1_c) of AlP, E(L_1_c) of AlAs, and E(L_1_c) of AlSb are discussed and attributed to various experimental uncertainties. Several other ...
Al, Au, Ti/Al and Ti/Au contacts were prepared on n-GaN and annealed up to 900 deg. C. The structure, phase and morphology were studied by cross-sectional transmission and scanning electron microscopy as well as by X-ray diffraction (XRD), the electrical behaviour by current-voltage measurements. It was obtained that annealing resulted in interdiffusion, lateral diffusion along the surface, alloying and bowling up of the metal layers. The current-voltage characteristics of as-deposited Al and Ti/Al contacts were linear, while the Au and Ti/Au contacts exhibited rectifying behaviour. Except the Ti/Au contact which became linear, the contacts degraded during heat treatment at 900 deg. C. The surface of Au and Ti/Au contacts annealed at 900 deg. C have shown fractal-like structures revealed by scanning electron microscopy. Transmission electron microscopy and XRD investigations of the Ti/Au contact ...
We use the Generalized Quasi-Chemical Approach (GQCA) combined with ab initio ultrasoft pseudopotential calculations within density functional theory in order to obtain the structural and electronic properties of Al_xGa_yIn_1_-_x_-_yX (X=As, P or N) quaternary alloys in the zincblende structure. Results for the bond lengths show that their variations with composition are approximately linear and that they do not deviate much from the values of the corresponding binary compounds. For the variation of the band gaps, we obtain a bowing parameter b=0.26 eV for the (Ga_0_._4_7In_0_._5_3As)_z(Al_0_._4_8In_0_._5_2As)_1_-_z quaternary alloy lattice matched to InP, in very good agreement with experimental data. In the case of AlGaInN, a bowing parameter of 0.22 eV is obtained for zincblende AlGaInN lattice matched to GaN. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)
Inverted growth and the development of associated cell processing, are likely to offer a significant degree of freedom for improving the performance of many III-V multijunction cascades and open new avenues for advanced multijunction concepts. This is especially true for the development of high-efficiency Al[sub 0.37]Ga[sub 0.63]As/GaAs cascades where the high growth temperatures required for the AlGaAs top cell growth can cause the deterioration of the tunnel junction interconnect. In the approach of inverted-grown AlGaAs/GaAs cascade cells, the AlGaAs top cell is grown first at 780 [degree]C and the GaAs tunnel junction and bottom cell are grown at 675 [degree]C. After the inverted growth, the AlGaAs/GaAs cascade structure is selectively removed from the parent substrate. The feasibility of inverted growth is demonstrated by a fully-processed, inverted-grown, thin film GaAs cell ...
After being pre-plated a zinc layer, an amorphous Al-Mn alloy coating was applied onto the surface of AZ31B magnesium alloy with a bath of molten salts. Then the corrosion performance of the coated magnesium alloy was examined in 3.5% NaCl solution by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The results showed that the single Zn layer was active in the test solution with a high corrosion rate while the Al-Mn alloy coating could effectively protect AZ31B magnesium alloy from corrosion in the solution. The high corrosion resistance of Al-Mn alloy coating was ascribed to an intact and stable passive film formed on the coating. The performances of the passive film on Al-Mn alloy were further investigated by Mott-Schottky curve and X-ray photoelectron spectroscopy (XPS) analysis. It was confirmed that the passive film exhibited n-type semiconducting behavior in 3.5% NaCl ...
Scanning electron microscopy and an electron-microprobe analysis of a sample of blast furnace (BF) coke have revealed alkalization (5.64 wt % Na{sub 2}O + K{sub 2}O) and Al saturation (17.28 wt % Al{sub 2}O{sub 3}) of SiO{sub 2} by BF gases. The K/Na{sub at} value of 1.15 in the new phase (alteration zone) reflects close atomic proportions of the elements and suggests that the abilities to incorporate K and Na during the process are almost equal. This Al saturation and alkalization of SiO{sub 2} indicates an active role for Al along with alkali metals in BF gases. The average width of the altered area in the SiO{sub 2} grain is about 10 m, which suggests that SiO{sub 2} particles of that size can be transformed fully to the new phase, provided that at least one of their faces is open to an external pore (surface of the coke) or internal pore with circulating BF gases. The grains that exceed 10 {mu}m can ...
Shell Solar GmbH is working on a variant of the so-called stacked elemental layer process for CIGSSe absorber production. The metal films resp. the selenium are deposited on the Mb electrode at room temperature by DC sputtering (CIG) or evaporation (Se) and then processed into semiconductors by rapid thermal annealing (RTP). Currently, the mean efficiency of the pilot plant is i 12.6 {+-} 0.2 % for non-sealed 30 x 30 cm{sup 2} modules, the key efficiency is 13.0 %. In addition to the 30 x 30 cm{sup 2} pilot line, a small series of 60x90cm2 modules was constructed in December 2004. Here, the mean efficiency was 13.0 percent while the average module power was higher than 60 W. The contribution also describes investigations of ceramically sputtered n-ZnO:Al layers with reduced Al concedntrations of 1 percent and on reactively sputtered n-ZnO.Al layers from the double roller magnetron. (orig.) [German] Bei Shell Solar GmbH wird ...
Continuous wave operation of an Al/sub 0.21/Ga/sub 0.31/In/sub 0.48/P /Ga/sub 0.52/In/sub 0.48/P /Al/sub 0.21/Ga/sub 0.31/In/sub 0.48/P double heterostructure (DH) laser diode was achieved for the first time at 77 K. The device was made from a DH wafer grown by atmospheric metalorganic chemical vapor deposition using triethyl metals and phosphine as source materials. At 77 K, the lasing wavelength was 0.653 ..mu..m and the threshold current was 55 mA for a diode with a nitride-insulated, 8-..mu..m-wide and 250-..mu..m-long stripe geometry.
l-Carnitine is a critical metabolite indispensable for the metabolism of lipids as it facilitates fatty acid transport into the mitochondrion where b-oxidation occurs. Human astrocytes (CCF-STTG1 cells) and hepatocytes (HepG2 cells) exposed to aluminum (Al) and hydrogen peroxide (H2O2), were characterized with lower levels of l-carnitine, diminished b-oxidation, and increased lipid accumulation compared to the controls. g-Butyrobetainealdehyde dehydrogenase (BADH) and butyrobetaine dioxygenase (BBDOX), two key enzymes mediating the biogenesis of l-carnitine, were sharply reduced during Al and H2O2 challenge. Exposure of the Al and H2O2-treated cells to a-ketoglutarate (KG), led to the recovery of l-carnitine production with the concomitant reduction in ROS levels. It appears that the chann...
Alumina-reinforced carbon nanofiber nanocomposites were prepared using different routes; powders mixture, colloidal route and sol?gel process followed by spark plasma sintering (SPS). CNFs/xAl2O3 (x = 10?50 vol.%) were prepared through nanopowders mixing in a high-energy attrition milling. The main limitations in the preparation of this kind of nanocomposites are related to the difficulty in obtaining materials with a homogeneous distribution of both phases and the different chemical nature of CNFs and Al2O3, which causes poor interaction between them. A surface coating of CNFs by wet chemical routes with an alumina precursor is proposed as a very effective way to improve the interaction between CNFs and Al2O3. An improvement of 50% in fracture strength was found for similar nanocomposite ...
In this study, the influence of Beryllium (Be) content on the fracture behaviour of Al?15%Mg2Si composite was investigated. The results showed an increase in mechanical properties with increasing of Be content. The stress?strain curves of samples showed a same category of serrations reflecting non-uniform deformation. Scanning electron microscopy was employed to examine the crack nucleation and fracture model. The results indicate that Al?15%Mg2Si composite shows different behaviours of crack initiation and fracture for samples with and without Be. Differences observed in the fracture behaviour were attributed to microstructural changes as well as morphological aspects of primary Mg2Si particles.
Room-temperature continuous-wave (cw) operation of a GaInP/AlGaInP multiquantum well (MQW) laser was achieved for the first time. The threshold current was 70 mA at 22 /sup 0/C for a device with an 8-..mu..m-wide and a 250-..mu..m-long planar stripe. The emission wavelength was 668 nm. The characteristic temperature T/sub 0/ was 138 K under cw operation. The wafer with the MQW structure composed of 100-A-thick GaInP wells and 40-A-thick AlGaInP barrier layers was grown by atmospheric pressure metalorganic chemical vapor deposition.
The microstructure and tensile properties of Ti-44Al-6V-3Nb-0.3Y (at.%) alloy after canned forging were investigated. SEM results showed that the TiAl pancake exhibits inhomogeneous microstructure, which can be ascribed to the temperature drop and friction between billet and outer pack during forging, as well as the intrinsic anisotropy of lamellar colony. By means of TEM observation and EBSD analysis, the microstructure in the dominant area of the pancake was further characterized. This deformation area consists of 87.7% content of g grains plus some refined lamellar colonies and the rest of B2 grains. The grain size ranges between 1mm and 8.5mm. High-angle boundaries dominate the deformation microstructure, several substructures and twins are observed as well. Additionally, current forge...
The highest equilibrium free-carrier doping concentration possible in a given material is limited by the ''pinning energy'' which shows a remarkable universal alignment in each class of semiconductors. Our first-principles total energy calculations reveal that equilibrium n -type doping is ultimately limited by the spontaneous formation of close-shell acceptor defects: the 3- -charged cation vacancy in AlN, GaN, InP, and GaAs and the 1- -charged DX center in AlAs, AlP, and GaP. This explains the alignment of the pinning energies and predicts the maximum equilibrium doping levels in different materials. (c) 2000 The American Physical Society
The development of new efficient afterglow phosphors is currently hampered by a limited understanding of the persistent luminescence mechanism. Radioluminescence (RL) and x-ray absorption measurements on the persistent phosphor SrAl2O4:Eu,Dy were combined to reveal possible valence state changes for the rare earth (co)dopants. Traps in the phosphor material are quickly filled when exposing thermally emptied SrAl2O4:Eu,Dy powder to x rays. On the same time scale a partial oxidation of Eu2+ to Eu3+ is observed by x-ray absorption near-edge spectroscopy (XANES), while for the trivalent dysprosium the valence state remains unchanged. The impact of these observations on the recently proposed models for persistent luminescence is discussed.
X-ray photoelectron spectroscopy measurements indicate that the Ce{sup 3+} like fraction in {gamma}-Al{sub 2}O{sub 3} supported CeO{sub 2} can be decreased by the incorporation of La{sup 3+}. If La{sup 3+} is incorporated into the {gamma}-Al{sub 2}O{sub 3} before CeO{sub 2} is added, a higher CeO{sub 2} dispersion and a greater range of reversible reducibility of the CeO{sub 2} may also be obtained. These changes offer potential for improvement in the oxygen storage capacity provided by CeO{sub 2} in three-way catalysts. The actual effect of La{sup 3+} incorporation on the activity and durability of a Pt catalyst is assessed by a combination of temperature programmed reduction and flow reactor measurements.
In this paper, a Kramers-Kronig (KK) analysis of infrared (IR) reflectance spectrum of quaternary In_0_._0_1Al_0_._0_6Ga_0_._9_3N film grown by molecular beam epitaxy (MBE) is reported. The infrared measurement is performed in the reflection mode at an incident angle of 15 degree sign by Fourier transform infrared (FTIR) spectroscopy at T = 300 K. The Kramers-Kronig analysis of the reflectivity data has been used to obtain the real and imaginary parts of the index of refraction (n and k), and the real and imaginary parts of the dielectric response function (#epsilon#' and #epsilon#') of the materials. Finally, the transverse optical and longitudinal optical phonons for quaternary In_xAl_yGa_1_-_x_-_yN were obtained.
The present conference discusses plasma-assisted surface coating/modification processes, the applications to date of ion nitriding, the effects of nitrogen on metal surfaces, ion nitriding mechanisms in Cr, Al and Cr + Al-containing 1040 steel, ion nitriding of Al and its alloys, life enhancement for forging dies, novel anode plasma nitriding developments, and a comparative study of the pulsed and dc ion-nitriding behavior in specimens with blind holes. Also discussed are the influence of heating method on ion nitriding, surface hardening of marage steels by ion nitriding without core hardness reduction, plasma nitriding of nodular cast iron sput gears, NbN composites for superconductors, the carburization of tungsten in a glow discharge methane plasma, economic considerations concerning plasma nitriding, and the corrosion properties obtained by ion nitriding.
Erosion-corrosion (E-C) of 3003 aluminum (Al) alloy in ethylene glycol-water solutions were studied by weight-loss and electrochemical measurements as well as surface characterization through an impingement jet system. Al alloy E-C is dominated by erosion components, i.e., pure erosion and corrosion-enhanced erosion, which account for 92-97% of the total E-C rate under the various conditions in this work. Contribution from corrosion components, including pure corrosion and erosion-enhanced corrosion, is slight. With the increase of fluid flow velocity and sand concentration, the total E-C rate increases. Compared with the significant increase of the rates of erosion components, the increase of the rate of corrosion component is negligible. Upon fluid flow, passivity of Al alloy that develo...
A series of SiAlON materials with a cordierite-based matrix were annealed for different lengths of time to cause crystallization of the glass phase. Their fracture toughness, hardness, and elastic modulus were measured from room temperature up to 1100"0C. The fracture toughness generally decreased with temperature. Short time annealing raised toughness at lower temperatures, while further annealing lowered it back to the value for as-hot pressed materials. At higher test temperatures annealing had no effect on toughness. This annealing behavior is significantly different from that previously reported in the system SaAlON-YAG. Hardness decreased monotonically with temperature for all samples. Both hardness and the elastic modulus were not affected by the annealing treatment. At elevated temperatures appreciable scatter of modulus results allowed only a rough trend of decrease with temperature to be observed.
Useful bipolar transistor action over the temperature range from -195 to 550 /sup 0/C has been demonstrated for heterojunction bipolar transistors in the GaP/AlGaP chemical system. This represents the highest temperature at which useful bipolar solid-state transistor action has ever been demonstrated in any material. Improvements in the materials technology and in the understanding of device characteristics at high temperatures were essential to the successful fabrication of these devices. These results demonstrate that the GaP/AlGaP heterojunction system is an excellent technology for active electronic components operated at high temperatures.
The authors discuss several aspects of defect formation in epitax heterostructures based on solid solutions of A"3B"5 semiconductor compounds; these heterstructures were prepared by liquid phase epitaxy by cooling suitable high-temperature solutions from the initial growth temperature. An analysis shows that the regions near heterojunctions are regions of increased defect density even in compositions based on Al /SUB x/ Ga /SUB 1-x/ As-GaAs, Al /SUB x/ Ga /SUB 1-x/ P-GaP, Al /SUB x/ Ga /SUB 1-x/ Sb-GaSb, where the differences in lattice parameters of the contacting materials are a minimum.
The evolution of intergranular lattice strains in a textured, forged bar (Bar) sample of the #alpha# - #beta# titanium alloy Ti-6Al-4V has been characterised using in situ X-ray diffraction. A two-phase elastic-plastic self-consistent (EPSC) model has been developed to rationalise the results. Of the orientations analysed, it is found that the #left brace#2 0 0#right brace# #beta# orientation is the most compliant and that load partitions to this orientation during plasticity. The results from the bar material have then been used to predict the response of unidirectionally rolled plate (UD) Ti-6Al-4V. It is predicted that the residual lattice strains in the #left brace#101-bar0#right brace# and #left brace#112-bar0#right brace# orientations will be significantly higher in the UD material.
Combined electron, photon, and intense UV irradiation tests have been carried out on three mirror designs, (Si, Al/sub 2/O/sub 3/)/sub 2/Ag, (Si, SiOx)nAg, and (ZnS, Al/sub 2/O/sub 3/)4Ag, to investigate their suitability for space-borne chemical laser applications. It is found that the (Si, oxide)nAg enhanced-reflectance design is a viable candidate for such applications, whereas ZnS, in combination with either ThF/sub 4/ or Al/sub 2/O/sub 3/, shows unacceptably high absorption increases at the 2.8-micron HF laser wavelength with irradiation. It is pointed out, however, that further experiments are needed to fully understand the effect of irradiation on the (Si, oxide)nAg enhanced-reflectance mirrors.
In this work, effects of coolant chemistry, including concentrations of chloride ions and ethylene glycol and addition of various ions, on corrosion of 3003 Al alloy were investigated by electrochemical impedance spectroscopy measurements and scanning electron microscopy characterization. In chloride-free, ethylene glycol-water solution, a layer of Al-alcohol film is proposed to form on the electrode surface. With the increase of ethylene glycol concentration, more Al-alcohol film is formed, resulting in the increase in film resistance and charge-transfer resistance. In the presence of Cl- ions, they would be involved in the film formation, decreasing the stability of the film. In 50% ethylene glycol-water solution, the threshold value of Cl- concentration for pitting initiation is within ...
MCrAlY coatings are widely used on hot section components of gas turbines to provide hot corrosion and/or oxidation protection by formation of an oxide layer on the surface. As the protective oxide scale exfoliates during service, aluminum from the coating diffuses outward for reformation of the protective scale. Aluminum may also diffuse inward due to the differences in composition between the coating and the substrate. Thus, the coatings degrade due to oxidation, oxide scale spallation, and inward and outward diffusion of aluminum. Service life of these coatings is controlled by the aluminum content in the coating, operating temperature and start- shutdown cycles. In-service degradation of CoCrAlY and CoNiCrAlY coatings is presented. A procedure to predict the remaining service life of coatings under oxidizing conditions is discussed. (orig.) 12 refs.
In the present work, bulk amorphous and nanocrystalline Al83Fe17 alloys were obtained by consolidation of mechanically alloyed powders. Mechanical alloying of Al-17% Fe powder mixture yielded powder with an amorphous structure. Thermal behaviour of the milling product was examined using differential scanning calorimetry. This investigation revealed that the amorphous phase crystallised above 380^oC. The amorphous powder was compacted under a pressure of 7.7GPa in different conditions: at 380^oC for 600s and at 1000^oC for 180s. Structural investigations of the bulk material revealed that the amorphous structure was retained after consolidation process applied at 380^oC. Compaction under high pressure at 1000^oC caused crystallisation of the amorphous phase and appearance of metastable nano...
It is generally known that a number of metallic glasses have excellent corrosion resistance in a variety of chemically hostile environments. Consequently, the use of laser cladding to coat a massive crystalline material such as aluminium with a layer of a metallic glass has obvious advantages. In this paper, the authors will show that the formation of a predominantly amorphous layer of Zr_6_0Al_1_5NI_2_5 alloy by laser processing is possible, if the obstacles to amorphization are overcome. In addition, evidence of the excellent corrosion resistance of this alloy in a NaCl solution will be given. A comparative study of the corrosion behavior of this amorphous alloy with pure aluminium and Al-Cr alloy will be done, in order to complete previous studies of laser processed coatings of aluminum substrates.
We report on characterization of a set of AlGaN/GaN multiple-quantum-well (MQW) photodetectors. The model structure used in the calculation is the p-i-n heterojunction with 20 AlGaN/GaN MQW structures in i-region. The MQW structures have 2nm GaN quantum well width and 15nm AlxGa1-xN barrier width. The cutoff wavelength of the MQW photodetectors can be tuned by adjusting the well width and barrier height. Including the polarization field effects, on increasing Al mole fraction, the transition energy decreases, the total noise increases, and the responsivity has a red shift, and so the detectivity decreases and has a red shift.
This paper presents a patient specific deformable heart model that involves the known electrical and mechanical properties of the cardiac cells and tissue. The whole heart model comprises ten Tusscher's ventricular and Nygren's atrial cell models, the anatomical and electrophysiological model descriptions of the atria (introduced by Harrild et al.) and ventricle (given by Winslow et al.), and the mechanical model of the periodical cardiac contraction and resting phenomena proposed by Moireau et al. During the propagation of the depolarization wave, the kinetic, compositional and rotational anisotropy is handled by the tissue, organ and torso model. The applied patient specific parameters were determined by an evolutionary computation method. An intensive parameter reduction was performed u...