Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

Energy Technology Data Exchange (ETDEWEB)

Utilisation of geothermal energy may soon become an important factor in power supply in Germany. The contribution discusses the utilisation of hydrothermal low-pressure systems, the geological boundary conditions, the technical design of the thermal water cycle, and the current status of the hot dry rock technology. [German] Die Nutzung der Energie ausd Erdwaerme kann in naher Zukunft eine wichtige Rolle in der Energieversorgung Deutschlands spielen. Der vorliegende Artikel gibt einen Ueberblick ueber die Nutzung hydrothermaler Niederdrucksysteme, die geologischen Rahmenbedingungen, den technischen Aufbau des Thermalwasserkreislaufes sowie zum aktuellen Stand des Hot Dry Rock Verfahrens.

Energy Technology Data Exchange (ETDEWEB)

This seminar on the subject of ``electrical smog`` welcomed participants from Bavarian environmental consultancy agencies, rural and urban district authorities, ministries, consume-consultancy agencies and public health authorities. Leading scientists from research and authorities gave papers on the sources, exposure and effects/actions of electromagnetic fields and present the current state of knowledge about the hazards and risk of this radiation for human health. The proceedings in hand provide the papers given on the following topics: electromagnetic fields - and introduction to relevant issues; low-frequency fields - sources and exposure; high-frequency fields - sources and exposure; biological actions and effects of low-frequency fields; biological actions and effects of high-frequency fields; low-frequency fields - helath risk assessment; high-frequency fields - health risk assessment. (Uhe) [Deutsch] Das Seminar zum Thema Elektrosmog wurde fuer Teilnehmer ...

Energy Technology Data Exchange (ETDEWEB)

This seminar dealt with the subject of indoor air pollution and welcomed participants from environmental consultancy agencies and authorities and institutions related with environmental protection. Leading scientists from research and authorities presented the current state of knowledge abut the risks of indoorair pollution. The papers contained in these proceedings addressed: room climate and sick-building syndrome; allergens in indoor spaces; pollutants emitted by exemplary building materials; pollutant levels of organic compounds in indoor spaces; air quality in motor vehicle interiors; indoor air pollution - risk assessment and need for actions. (Uhe) [Deutsch] Das Seminar zum Thema Innenraumluft wurde fuer TeilnehmerInnen von Umweltberatungsstellen und anderen mit Umwelt betrauten Behoerden und Institutionen veranstaltet. Fuehrende Wissenschaftlerinnen aus Forschung und Behoerden stellten den aktuellen Stand des ...

Energy Technology Data Exchange (ETDEWEB)

The contribution outlines the current status of the building construction projects for the German Bundestag in Berlin. The following subjects are discussed: Energetic quality of the building, energy supply concept, integrated energy supply system, electric CHP systems, cogeneration (vegetable oil), aquifer storage (heat storage, cold storage), solar energy (photovoltaic energy conversion, thermal solar energy use), economic and ecological aspects. (HW) [Deutsch] Der vorliegende Beitrag gibt einen Ueberblick ueber den aktuellen Stand des Bauvorhabens des Deutschen Bundestages in Berlin. In diesem Zusammenhang wird auf folgende Themen eingegangen: Energetische Gebaeudequalitaet, Energieversorgungskonzept, Energieverbund, stromgefuehrte BHKWs, Kraft-Waerme-Kopplung (Pflanzenoel), Aquiferspeicher (Waermespeicher, Kaeltespeicher), Sonnenergienutzung (Photovoltaik, thermische Solarenergienutzung), Wirtschaftlichkeit und Oekologie. (HW)

Energy Technology Data Exchange (ETDEWEB)

The liberalisation of the energy markets requires completely new demands to the information processing procedure of energy supply enterprises. These requirements are to be understood as chances for strengthening of the terms of competition. In the following contribution to this subject the actual status of the concept as converted by the Electricity Supply Company of Halle (Saale) including their departments of district heating, gas and electricity supply will be presented. This concept are comprising all experiences as gathered so far as well as intended further actions to be executed. (orig.) [German] Die Liberalisierung der Energiemaerkte stellt fuer Versorgungsunternehmen voellig neue Anforderungen an die Informationsverarbeitung. Diese Anforderungen sind als Chancen zur Staerkung der Wettbewerbsfaehigkeit zu verstehen. Die Verfasser erlaeutern den aktuellen Stand des in der EVH GmbH Halle (Saale) im Querverbund der Sparten Fernwaerme, Gas ...

Energy Technology Data Exchange (ETDEWEB)

Numerous task forces at universities, other research institutions and in industry have been concerned with the development of methods fit to replace animal experiments. A great many useful in-vitro test systems were developed. From 1986 to 1993 the ``In-vitro Systems`` newsletter was published with the support of the federal ministry of science and technology. Its purpose was to intensely promote the concept of in-vitro systems for the benefit of experimental animals among scientists, and to demonstrate to the public the limits of such endeavours. This brochure is a compilation of 141 contributions from all annual volumes, dealing inter alia with research projects for the development of pharmaceuticals, toxicology and quality control, ethic-philosophical considerations, meeting reports, and book reviews. Changes or revisions have not been made; so some of the contributions have been overtaken by more recent developments. (MG) [Deutsch] Viele Arbeitsgruppen an Universitaeten, anderen ...

Science.gov (United States)

... THE STANDING JSOTF HEADQUARTERS IN A STANDING JOINT TASK FORCE HEADQUARTERS OR COMBATANT COMMAND ...

Energy Technology Data Exchange (ETDEWEB)

Shell Solar GmbH is working on a variant of the so-called stacked elemental layer process for CIGSSe absorber production. The metal films resp. the selenium are deposited on the Mb electrode at room temperature by DC sputtering (CIG) or evaporation (Se) and then processed into semiconductors by rapid thermal annealing (RTP). Currently, the mean efficiency of the pilot plant is i 12.6 {+-} 0.2 % for non-sealed 30 x 30 cm{sup 2} modules, the key efficiency is 13.0 %. In addition to the 30 x 30 cm{sup 2} pilot line, a small series of 60x90cm2 modules was constructed in December 2004. Here, the mean efficiency was 13.0 percent while the average module power was higher than 60 W. The contribution also describes investigations of ceramically sputtered n-ZnO:Al layers with reduced Al concedntrations of 1 percent and on reactively sputtered n-ZnO.Al layers from the double roller magnetron. (orig.) [German] Bei Shell Solar GmbH wird eine Variante des sogenannten ...

Wastenet

... It stands at a precipice of \\

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

Attention Deficit Hyperactivity Disorder (ADHD) is a neurobiological disorder of early childhood onset. Defining symptoms are chronic impairments of attention, impulse control and motor hyperactivity that frequently persist until adulthood. Miscellaneous causes of the disorder have been discussed. Accumulating evidence from imaging- and molecular genetic studies strengthened the theory of ADHS being a predominantly inherited disorder of neurobiological origin. In the last 15 years, non-invasive brain imaging methods were successfully implemented in pediatric research. Functional magnetic resonance imaging studies gave major insight into the neurobiological correlates of executive malfunction, inhibitory deficits and psychomotoric soft signs. These findings are in good accordance with brain morphometric data indicating a significant volumetric decrease of major components of striato-thalamo-cortical feedback loops, primarily influencing prefrontal executive functioning (e.g. basal ...

Energy Technology Data Exchange (ETDEWEB)

Already in 1998, the city of Hanover, the Stadtwerke Hannover and six further cities of the region initiated the funding programme 'Hannover proKlim' for promoting energy-relevant modernization measures in domestic buildings. One year later, the social marketing campaign 'Haus-Partner Hannover / Der (H)Eissbaer'' was started, which addresses building owners in Hanover with the intention to induce them to action. The 'Energiepass Hannover' is another important instrument of the campaign. This report takes stock of the results achieved so far. [German] Beim Klimaschutz im Gebaeudebestand lassen sich in Hannover drei Ansaetze hervorheben, die parallel zueinander entwickelt wurden und die in besonderer Weise dazu beitragen, die CO{sub 2}-Emissionen im Gebaeudebestand zu reduzieren: Bereits 1998 hat die Landeshauptstadt Hannover gemeinsam mit den Stadtwerken Hannover und sechs weiteren Staedten der Region den Klimaschutz-Fonds ...

Energy Technology Data Exchange (ETDEWEB)

The high-strength and ultra high-strength steels developed and produced by Thyssen Krupp Stahl make a major contribution to automotive lightweighting. Proven and newly-developed coatings are used to meet increasingly important corrosion protection requirements. Design for materials, optimized forming and joining processes and the use of modern simulation techniques help to exploit the potential of the new steels. Future development work will focus on reducing the density of steels without compromising their well-known advantages - in particular their strength. The use of high-strength and ultra high-strength steels in the automotive industry is on the increase. Steel will remain the material of choice for auto manufacture, above all due to its potential for cost-efficient lightweight construction and its full recyclability. (orig.) [German] Einen wesentlichen Beitrag zum Leichtbau im Automobil leisten die von Thyssen Krupp Stahl entwickelten und hergestellten ...

Energy Technology Data Exchange (ETDEWEB)

A small cable yarding system for accumulations of slash on forested land and overstocked non-productive stands is described.

Energy Technology Data Exchange (ETDEWEB)

To study the biogeochemical behaviour, mobility and transport of trace metals in seawater (Se, Mo, Cd, Pb, Hg, Cu, Co, Fe, Ni, Zn), in suspended particulate matter (Mo, Cd, Pb, Cu, Co, Fe, Ni, Zn, Al, Mn) and in sediments of the inner and outer coastal regions, samples were collected on 3 separate cruises during a one year period (Mai 1993 - April 1994) at 20 stations in the coastal area of Mecklenburg-Vorpommern. Standard hydrographic parameters, nutrients and dissolved oxygen were also measured. Priority was taken to establish the methods for the determination of molybdenum and selenium. To study the behaviour of these two elements in detail, longterm measurements were carried out weekly between January 1993 and June 1994 at the `Messsteg/Warnemuende`. Because of parallel measurements correlations to biological, chemical and hydrographic parameters have been tested. The total database is summarized in the Appendix. The results are presented in 30 figures and 13 tables and are ...

Energy Technology Data Exchange (ETDEWEB)

Short communication

CSIR Research Space (South Africa)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In the future even more than in the past, nuclear power will be indispensable in the present industrialized countries and in those still under development. The safe, nonpolluting, and economic supply of energy to mankind in the future includes so many different problems that the technology of the high-temperature reactor at its present level of development, and with the possibilities is offers above and beyond those provided by other, established, technologies, does not have to mark the end of some old line of development, but rather should be seen as the starting point of a development offering promise for the future. It is for this very reason that the extensive, valuable knowledge and experience accumulated in the construction, operation, and decommissioning of the AVR and THTR plants, the development of the HTR module and other variants and, last, but not least, the valuable results of projects such as PNP, NFE, and HHT, must be preserved at the research centers and with former ...

Science.gov (United States)

Mar 30, 2007 ... Tropical forests are home to half the Earth's species, and their trees are an immense standing reservoir of carbon. Deforestation will have ...

Science.gov (United States)

depth timber industry experience with state-of-the-art ... difficult to find high-value pockets of timber (also known as timber stands ) to supply his ...

Science.gov (United States)

... 124 Headquarters, 82nd Airborne Division, 82nd Airborne Division Airborne Standing Operating Procedures ... the Light Infantry divisions during the ...

UK PubMed Central (United Kingdom)

Cerebral periventricular white matter injury stands as a leading cause of cognitive, behavioral and motor impairment in preterm infants. There is epidemiological and histopathological evidence...Full Text Available

Science.gov (United States)

... WHS- Washington Headquarters Service. ... The standing Joint Task Force concept should be used more to provide warfighter forces and ...

Energy Technology Data Exchange (ETDEWEB)

This publication contains the Ordinance on Heating Costs, the Ordinance on Heating Installations, and the 1st Federal Ordinance on Emission Control (BImSchV) concerning Small-Scale Furnaces, in each case with notes and explanations. All these ordinances aim at reducing energy consumption in connection with heating; the 1st BImSchV also at air pollution abatement by lowering the permissible limiting values for soot and flue gas. The three ordinances also apply to housing property. (HSCH).

British Library Electronic Table of Contents (United Kingdom)

The rolls and stand deflections induced by rolling force lead to a significant decrease in the radius prediction accuracy of the ring product in the in-plane roll-bending of strip. To precisely predict the deflections and control the radius, a new analytical model is developed. Numerical implementation is presented to solve the theoretical rolling force, the deflections as well as the inherent force-deflection relationship considering the interactions of the strip workpiece, the rolls and the stand. A series of profile measurements of the formed ring parts are made to assess the accuracy of the predicted deflections. Different control approaches are used in the experiments to validate the radius control model. The experimental results show that the model is reliable to control the radii wi...

Energy Technology Data Exchange (ETDEWEB)

The analyses were carried out using real climate data for the years 1987 and 1989. The course of the indoor climate for year-round free ventilation with a constant flow volume is discussed. Numerous diagrams inform on ambient temperature, water vapour content, the condition of space air, and temperature drops below dew point. For the event of heating of the central part of the church, space air condition, the annual air humidification requirement, and the temperature field in this part of the building are described. (MSK) [Deutsch] Die Untersuchungen wurden mit aktuellen Klimadaten fuer die Jahre 1987 und 1989 durchgefuehrt. Der Verlauf des Raumklimas bei ganzjaehrig freier Klimatisierung mit konstantem Foerderstrom wird erlaeutert. Dabei wird die Raumlufttemperatur, der Wasserdampfgehalt, der Raumluftzustand sowie die Taupunktunterschreitung in zahlreichen Diagrammen aufgezeigt. Weiter werden fuer den Fall der Beheizung des Hauptraums der Kirche der ...

UK PubMed Central (United Kingdom)

AbstractObjectiveThis study aimed at determining the standing spinal landmark that corresponds to the inferior tip of the scapula and determining the accuracy of experienced...Full Text Available

UK PubMed Central (United Kingdom)

IntroductionMale sexual dysfunction is a common complication of diabetes (DM), but the relative impact of erectile dysfunction (ED), orgasmic dysfunction (OD), and/or...Full Text Available

UK PubMed Central (United Kingdom)

How sensory organization for postural control matures in children is not clear at this time. The present study examined, in children aged 7 to 11 and in adults, the postural control modifications in...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The authors introduce the above electric car. They deal particularly with the vehicle concept, the energy consumption and the emission balance. (orig.).

UK PubMed Central (United Kingdom)

If we are to stand any chance of understanding the circuitry of the superficial dorsal horn, it is imperative that we can identify which classes of interneuron are excitatory and which are inhibitory....Full Text Available

UK PubMed Central (United Kingdom)

BackgroundThe TNF/LTA locus has been a long-standing T2D candidate gene. Several studies have examined association of TNF/LTA...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

An analysis on landscape level was performed to investigate the growth of Scots pine stands (Pinus sylvestris L.) in the research area of 'Duebener Heide' under the impact of rapidly changing pollution loads and to evaluate their further development. Central to the work was a spatial database, installed using a geographic information system (GIS). This database enabled the statistical analysis of relationships and correlations between the growth of the pine stands, the influence of pollution impacts and the natural site characteristics. The results of emission and immission modelling gave detailed evaluation of the pollution load over the investigated area. The spatial information database was linked with a process-based growth model called FORSANA. The resulting regional model was used to simulate forest growth on stand level for variable time periods. The plausibility of the simulation results of the ...

UK PubMed Central (United Kingdom)

We used the idea of hierarchical control to study multi-muscle synergies during a whole-body sway task performed by a standing person. Within this view, at the lower level of the hierarchy,...Full Text Available

UK PubMed Central (United Kingdom)

An 11-year-old mare presented 36 hours after foaling with a ruptured bladder. Uroperitoneum was diagnosed on ultrasound and from the creatinine concentration of the peritoneal fluid. Bladder endoscopy...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The volume contains reports on plant technology, on systems organisation with the aim to minimize the risk (human error), on the problem of seismic risk, on core-disruptive accidents and on accident consequence models with different release categories and a comparison of the potential damage incurred. Mr. Webb; one of the authors, attempts to disprove the objections to his two earliest SNR statements by experts of Karlsruhe Nuclear Research Centre.

British Library Electronic Table of Contents (United Kingdom)

The model of `ecological forestry' has evolved as a part of the development of the concept of ecosystem management. `Ecological forestry' emphasises that manipulation of a forest ecosystem should consider, and as far as practicable work within the limits of, natural disturbance patterns prior to extensive human alteration of the landscape. This paper evaluates the extent to which forest management practices in jarrah (Eucalyptus marginata) and karri (Eucalyptus diversicolor) forests of south-western Australia align with this view of the characteristics and appropriate silviculture of `ecological forestry'. Characteristics and appropriate silviculture of `ecological forestry' are evaluated in relation to (i) the stand level decisions of stand structure and harvest timing and (ii) the landsc...

International Nuclear Information System (INIS)

This paper presents case studies of economic feasibility of solar photovoltaic systems using the software AVES-F (Analysis of Economic Feasibility of Photovoltaic Systems), developed by the authors, considering cases of stand-alone and grid-connected systems. The software takes into account several factors that can influence the economic feasibility of these kind of systems, like load to be supplied, distance to the grid, the use regime of the system, applied subsidies and others. The main goal of this paper is to analyze some of these factors and to observe how they can affect the economics of PV systems for electricity generation. (authors)

Energy Technology Data Exchange (ETDEWEB)

Reviewing all hitherto known plans or drafts for a reform of the atomic energy law, one can expect that the current legal concept of affording protection of existing (legal) status of nuclear facilities will not essentially be watered down by future developments, unless an act is passed for a nuclear power phase-out. (orig.) [Deutsch] Die bislang bekannt gewordenen Reformbestrebungen legen die Vermutung nahe, dass der Bestandsschutz fuer atomrechtliche Anlagen, sofern nicht ein Kernenergie-Abwicklungsgesetz zum Tragen kommt, mit Abstrichen auch in Zukunft rechtlichen Bestand haben wird. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The possibility of switching the heat transfer consists of varying heat transfer surfaces and making the heat transfer temporarily more intensive. Heat tubes prove to be particularly suitable, which must be exposed to a heat carrier fluid or removed from its effect for switching the heat transfer. This report gives a survey of the possibilities of switching heat flows and for making the heat transfer more intensive. Further, the report contains a survey of patents limited to heat transfer in the fields of cooling internal combustion engines and exhaust systems. (orig.) With 17 figs., 183 refs.

Energy Technology Data Exchange (ETDEWEB)

Together with an investigation on the deformation behavior of hot and cold rolled strip edge, the edge-drop control was explained in characteristics and result of application to the commercial mill by the tapered-crown work roll (WR) shifting mill. From a cold rolling experiment, three-dimensional material flow was known to be generated in the vicinity of edge also at the time of rolling the strip, and which generation influences that of edge-drop. Almost linearly relative to the flattened deformation of WR, the edge-drop enlarges with enlargement in that deformation. The number of stands to be applied to the tapered-crown WR shifting mill in the tandem cold mill is determined by the location as far as which the strip is to be controlled in edge-drop. In case of improving it to obtain the edge-drop-free strip, all the stands are required to be equipped with tapered-crown WR shifting mill. By applying a tapered-crown WR shifting mill to the ...

Energy Technology Data Exchange (ETDEWEB)

A free-electron laser (FEL) two-beam accelerator (TBA) is proposed, in which the FEL interaction takes place in a series of drive cavities, rather than in a waveguide. Each drive cavity is 'beat-coupled' to a section of the accelerating structure. This standing-wave TBA is investigated theoretically and numerically, with analyses included of microwave extraction, growth of the FEL signal through saturation, equilibrium longitudinal beam dynamics following saturation, and sensitivity of the microwave amplitude and phase to errors in current and energy. It is found that phase errors due to current jitter are substantially reduced from previous versions of the TBA. Analytic scalings and numerical simulations are used to obtain an illustrative TBA parameter set.

International Nuclear Information System (INIS)

In this paper, research on pass schedule of tandem cold mill (TCM) is carried out. According to load (reduction, rolling force, motor power) balance, non-linear equations set with variables of inter-stand thickness is constructed. The pass schedule optimization is carried out by solving the non-linear equations set. As the traditional method, the Newton-Raphson method is used for solving the non-linear equations set. In this paper a new simple method is brought up. On basis of the monotone relations between thickness and load, the inter-stands thickness is adjusted dynamically. The solution of non-linear equations set can be converged by iterative calculation. This method can avoid the derivative calculation used by traditional method. So, this method is simple and calculation speed is high. It is suitable for on-line control. (author)

British Library Electronic Table of Contents (United Kingdom)

Regular fuel reduction burning is an important management strategy for reducing the scale and intensity of wildfires in south-west Australian native forests, but the long term effects of this on tree and stand growth are not well understood. Five fire treatments, including application of frequent and infrequent low intensity burns, and 25?years of fire exclusion, were applied to small (4?ha) experimental plots in a low rainfall mixed jarrah (Eucalyptus marginata) and marri (Corymbia calophylla) forest to investigate the effects of these treatments on tree stem diameter growth, stand basal area increment and tree mortality. Mean tree stem growth measured over 20?years was lowest in the long unburnt treatment compared with the burn treatments, although surface soil nutrient levels were gener...

International Nuclear Information System (INIS)

The scattering of atoms by a resonance standing light wave is considered under conditions when the lower of two resonance levels is metastable, while the upper level rapidly decays due to mainly spontaneous radiative transitions to the nonresonance levels of an atom. The diffraction scattering regime is studied, when the Rabi frequency is sufficiently high and many diffraction maxima are formed due to scattering. The dynamics of spontaneous radiation of an atom is investigated. It is shown that scattering slows down substantially the radiative decay of the atom. The regions and characteristics of the power and exponential decay are determined. The adiabatic and nonadiabatic scattering regimes are studied. It is shown that the wave packets of atoms in the metastable and resonance excited states narrow down during scattering. A limiting (minimal) size of the wave packets is found, which is achieved upon nonadiabatic scattering in the case of a sufficiently long ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes a comprehensive MCM [machine condition monitoring] program and suggested system for implementation in hydroelectric generating units. The system addresses all the major subsystems which make up the generating unit. A modular design means that it could be applicable in a wide variety of situations. Different subsystems may be included or excluded from the monitoring system as required. It may be used at individual plants as a stand alone system or network wide. An advanced processing and diagnostic module is included, again for use as an integral part of the system or as a stand alone analysis tool. Examples of the system's proposed data analysis and diagnostic abilities are also described using vibration signals as would be provided by the bearing module. (Author)

International Nuclear Information System (INIS)

We present here for the first time the tele-robotics system for hot-cells MT200-TAO (TAO stands for Teleoperation Assistee par Ordinateur or Computer Assisted Tele-robotics), able to replace a conventional telescopic medium tele-manipulator (extension 4 m; capacity 20 kg). The system is currently under evaluation in COGEMA/AREVA- La Hague hot-cells. (authors)

CERN Document Server

How far can a stack of $n$ identical blocks be made to hang over the edge of a table? The question dates back to at least the middle of the 19th century and the answer to it was widely believed to be of order $\\log n$. Recently, Paterson and Zwick constructed $n$-block stacks with overhangs of order $n^{1/3}$, exponentially better than previously thought possible. We show here that order $n^{1/3}$ is indeed best possible, resolving the long-standing overhang problem up to a constant factor.

Energy Technology Data Exchange (ETDEWEB)

It is shown that observations of the lithium isotope ratio in high surface temperature Population II stars may be critical to cosmological nucleosynthesis models. In particular, decaying particle scenarios as derived in some supersymmetric models may stand or fall with such observations. 18 references.

Energy Technology Data Exchange (ETDEWEB)

Recent experiments have explored the use of a free-electron laser (FEL) as a buncher for a microwave two-beam accelerator, and the subsequent driving of a standing-wave rf output cavity. Here the authors present a deeper analysis of the longitudinal dynamics of the electron bunches as they are transported from the end of the FEL and through the output cavity. In particular, the authors examine the effect of the transport region and cavity aperture to filter the bunched portion of the beam.

Energy Technology Data Exchange (ETDEWEB)

This feasibility study of the uve Institut fuer Technische Chemie und Umweltschutz GmbH discusses the scientific and technical fundamentals of a catalytic process for complete removal of organic pollutants (PAH, H-HC, PCB, phenols, nitro-aromatics and organometallic compounds, e.g. from polluted soil and groundwater) by thermal-catalytic cracking and conversion into simple gases. The process is based on the catalytic reaction of the hydrocarbon compounds with water vapour in the temperature range of 700-900 degrees centigrade. The resulting gas mixtures consist mainly of hydrogen, carbon monoxide, carbon dioxide and methane which can be used as fuels, e.g. for heating or in gas engines. The process is an alterntive to combustion. It is therefore well suited whenever the pollutant to be removed is already mixed with water or water vapour and wherever in-situ removal would be too great a hazard. [Deutsch] Die vorliegende Machbarkeitsstudie aus dem uve Institut fuer Technische Chemie und ...

Energy Technology Data Exchange (ETDEWEB)

Different cooling speeds after previous solution annealing at 1130deg C for 0.5 hour were simulated in laboratory experiments. The following conditions were examined: (1) Direct water quenching, (2) cooling in air for 0.5 min to 950deg C/water quenching, (3) cooling in air for 1.5 min to 750deg C/water quenching, (4) cooling in furnace for 5 min to 750deg C/water quenching. The results of the investigations have shown that a variation of the cooling conditions causes considerable changes in the creep behaviour. (orig.).

Energy Technology Data Exchange (ETDEWEB)

To make a quantitative comparison of risks between the SNR-300 and a modern PWR (Biblis B), the consequences of an accident or the extent of damage of a release of radionuclides to the environment due to an accident are estimated by computer programs for accident consequence models. The accident analysis includes an analysis of events for Bethe-Tait accidents with failure of the outer containment. The FGSB release rates are compared with those of the Society for Reactor Safety (GRS).

Energy Technology Data Exchange (ETDEWEB)

In the first part of this contribution, the definition of reference values is given and the theoretical and practical problems in the application of this concept are discussed. In this connection, the present resources on instrumentation and the technical requirements for dose assessment are described. In the second part, some consequences are taken and proposals for further actions are made. (orig.) [German] Im ersten Teil des Aufsatzes werden die Definition von Referenzwerten in der radiologischen Diagnostik untersucht und die theoretischen und praktischen Probleme der Umsetzung des gesamten Konzepts eroertert. In diesem Zusammenhang werden auch der gegenwaertige Geraetebestand und die technischen Voraussetzungen zur Dosisermittlung beschrieben. Im zweiten Teil werden daraus Schlussfolgerungen gezogen und Vorschlaege zum weiteren Vorgehen gemacht. (orig.)

Energy Technology Data Exchange (ETDEWEB)

A consequent use of computers and standardized components enables high efficiency for steam turbines while produced at lower manufacturing cost as shown here in the Muehlheim company of Siemens Power Generation, where steam turbines are produced for new stations and retrofitted elder power plants. [German] Auch eine ueber hundert Jahre alte Technik bietet Raum fuer Innovationen: Konsequenter Computereinsatz und standardisierte Baureihen ermoeglichen bei Dampfturbinen hohe Wirkungsgrade bei relativ niedrigen Fertigungskosten - umgesetzt im Werk Muelheim der Siemens Power Generation, wo Dampfturbinen fuer Neuanlagen und zum Modernisieren bestehender Kraftwerke entstehen. (orig.)

Energy Technology Data Exchange (ETDEWEB)

In conjunction with the constellation of lawsuits within the administrative court system, and based on modern environmental protection laws, emission control laws, and foremost, the atomic energy laws, we are confronted with a variety of constitutional and administrative problems. However, the fundamental questions of individual rights within the potentially incriminating environmental utilization or exploitation by individuals could be relatively clearly answered by observing the basic principles of our legal order. It is to be expected that the administrative courts will arrive at acceptable decisions reflecting the full protection of the law and the basic constitutional principles, and that these - once made - may serve as orientation in superior court actions.

British Library Electronic Table of Contents (United Kingdom)

Trapezblechstege im Bruckenbau kommen trotz der groen Vorteile, die diese Bauweise bietet, in Deutschland bisher nur an einem Pilotprojekt zur Anwendung. Durch die charakteristischen Eigenschaften des Trapezbleches entstehen konstruktive und wirtschaftliche Vorteile gegenuber herkommlichen Bruckenbauweisen. Allerdings lassen die aktuell gultigen Regelwerke aufgrund fehlender Kenntnis zum Tragverhalten und mangelnder Erfahrung keine wirtschaftliche Ausbildung zu. Dies zeigt sich am Beispiel des Pilotprojekts. Die Ausbildung der Verbundfuge wurde hier nur sehr unbefriedigend gelost und verdeutlicht somit die Notwendigkeit einfacher und praktikabler Verbindungsmoglichkeiten. Am Institut fur Leichtbau Entwerfen und Konstruieren der Universitat Stuttgart wurde in Zusammenarbeit mit dem Institut...

Energy Technology Data Exchange (ETDEWEB)

The Linac Coherent Light Source (LCLS) is required to deliver a high quality electron beam for producing coherent X-rays. As a result, high resolution beam position monitoring is required. The Beam Position Monitor (BPM) digitizer acquires analog signals from the beam line and digitizes them to obtain beam position data. Although Matlab is currently being used to test the BPM digitizer?s functions and capability, the Controls Department at SLAC prefers to use Experimental Physics and Industrial Control Systems (EPICS). This paper discusses the transition of providing similar as well as enhanced functionalities, than those offered by Matlab, to test the digitizer. Altogether, the improved test stand development system can perform mathematical and statistical calculations with the waveform signals acquired from the digitizer and compute the fast Fourier transform (FFT) of the signals. Finally, logging of meaningful data into files has been added.

Energy Technology Data Exchange (ETDEWEB)

The Magnet Test Facility at Fermilab tests a variety of full-scale and model superconducting magnets for both R and D and production. As the design characteristics and test requirements of these magnets vary widely, the magnet test stand must accommodate a wide range of Data Acquisition (DAQ) and Control requirements. Such a system must provide several functions, which includes: quench detection, quench protection, power supply control, quench characterization, and slow DAQ of temperature, mechanical strain gauge, liquid helium level, etc. The system must also provide cryogenic valve control, process instrumentation monitoring, and process interlock logic associated with the test stand. A DAQ and Control system architecture that provides the functionality described above has been designed, fabricated, and put into operation. This system utilizes a modular approach that provides both extensibility and flexibility. As a result, the complexity of ...

Energy Technology Data Exchange (ETDEWEB)

Cuttings were taken from the upper part of the crowns of spruce trees 60-70 yr old in stands at 3 different altitudes in the Rila Mountains and 4 in the Vitosha Mountains in Bulgaria. The cuttings, of 1-yr, 2-yr and 3-yr shoots, were rooted in sand, perlite and peat. Rooting % generally decreased with increasing altitude of provenance, but cuttings from the very highest altitudes showed increased rooting %. In general, 1-yr cuttings gave the best rooting %, but in some provenances the 2-yr cuttings were best. Sand was clearly the best rooting substrate. (Refs. 11).

Energy Technology Data Exchange (ETDEWEB)

The Data Acquisition System for the CDMS II dark matter experiment was designed and built when the experiment moved to its new underground installation at the Soudan Lab. The combination of remote operation and increased data load necessitated a completely new design. Elements of the original LabView system remained as stand-alone diagnostic programs, but the main data processing moved to a VME-based system with custom electronics for signal conditioning, trigger formation and buffering. The data rate was increased 100-fold and the automated cryogenic system was linked to the data acquisition. A modular server framework with associated user interfaces was implemented in Java to allow control and monitoring of the entire experiment remotely.

International Nuclear Information System (INIS)

This is a preliminary study on the sound absorption properties of two tropical hardwoods, Light Red Meranti and Ramin, and their wood-polymer composites. Sound absorption is measured using a standing wave apparatus. The samples are of one thickness (7 mm) and cut longitudinally. Wood-polymer composites are made by impregnating the samples with methyl methacrylate which is polymerized in situ through #gamma#-irradiation. Both woods and their composites are better sound absorbers at higher sound frequencies. With partial impregnation, the absorption coefficients are improved upon particularly in the region between 1-3 kHz. (author).

British Library Electronic Table of Contents (United Kingdom)

The origin of life is a long-standing mystery puzzling many people. This mystery possesses not only philosophical but also important biological significance. To unveil this mystery, the searches for the root of life, or the last universal common ancestor (LUCA), based on comparative-genomic analysis have been intensively performed on rRNAs, tRNAs and proteins sequences. The current search pointed to a Methanopyrus-proximal LUCA, which opens up the reconstruction of Lucan biology and helps to delineate the evolutionary pathways.

Energy Technology Data Exchange (ETDEWEB)

A billet of low-density carbon-bonded carbon fiber (CBCF) composite is machined into a desired attenuator or load element shape (usually tapering). The CBCF composite is used as a free-standing load element or, preferably, brazed to the copper, brass or aluminum components of coaxial transmission lines or microwave waveguides. A novel braze method was developed for the brazing step. The resulting attenuator and/or load devices are robust, relatively inexpensive, more easily fabricated, and have improved performance over conventional graded-coating loads.

International Nuclear Information System (INIS)

Nuclear forensics is the analysis of nuclear materials recovered from either the capture of unused materials, or from the radioactive debris following a nuclear explosion and can contribute significantly to the identification of the sources of the materials and the industrial processes used to obtain them. In the case of an explosion, nuclear forensics can also reconstruct key features of the nuclear device. Nuclear forensic analysis works best in conjunction with other law enforcement, radiological protection dosimetry, traditional forensics, and intelligence work to provide the basis for attributing the materials and/or nuclear device to its originators. Nuclear forensics is a piece of the overall attribution process, not a stand-alone activity

Energy Technology Data Exchange (ETDEWEB)

In the framework of the carbon storage two forestry methods are analyzed by the author: the standing capitalization (slowing of the crops) and the spices substitution (slow growing species by fast growing species). The construction of a model taking into account the all stage of the carbon implication (biomass, soil, forest products) offers simulation and quantitative results on these methods. (A.L.B.)

Science.gov (United States)

We explore autofluorescence endomicroscopy as a potential tool for real-time visualization of epithelial tissue microstructure and organization in a clinical setting. The design parameters are explored using two experimental systems--an Olympus Medical Systems Corp. stand-alone clinical prototype probe, and a custom built bench-top rigid fiber conduit prototype. Both systems entail ultraviolet excitation at 266 nm and/or 325 nm using compact laser sources. Preliminary results using ex vivo animal and human tissue specimens suggest that this technology can be translated toward in vivo application to address the need for real-time histology.

International Nuclear Information System (INIS)

Thirty-seven patients with histologic proof of cholangiocarcinoma at the confluence were examined by computed tomography (CT) to determine whether this examination is of value in the assessment of these patients for surgery and whether there are any features specific to this type of tumor. Thirty-two patients showed intrahepatic duct dilatation; six of these showed dilatation of ducts in one lobe only. Eighteen patients had intrahepatic low-attenuation areas, while eight had a mass lesion in the porta hepatis. The results of this study show that CT provides useful anatomic information preoperatively but that the appearances are nonspecific. Lobar atrophy is highly suggestive of hilar cholangiocarcinoma, either of long-standing or with unilateral portal venous involvement.

CERN Document Server

In a recent breakthrough work, Chatterjee proved a long standing conjecture that relates the transversal exponent \\xi and the fluctuation exponent \\chi in first-passage percolation on Z^d. The purpose of this paper is to introduce a new and intuitive idea that replaces Chatterjee's main argument and gives an alternative proof of this relation. Specifically, we show that under the assumption that exponents (as defined by Chatterjee) exist, one has the relation \\chi \\leq 2\\xi -1. One advantage of our argument is that it does not require a `nearly Gamma' assumption on the edge-weight distribution.

Science.gov (United States)

This report has been prepared in conjunction with an environmental baseline study for a commercial coal conversion facility being conducted by Ashland Synthetic Fuels, Inc. (ASFI) and Airco Energy Company (AECO). This report represents a cultural resource assessment for the proposed plant site and two potential solid waste disposal areas. This assessment presents data collected by Dames and Moore during a recent archaeological reconnaissance of the unsurveyed southeastern portion of the proposed plant site and two potential solid waste disposal areas. Also, results of two previous surveys on the northern and southwestern portion of the plant site for American Smelting and Refining Company (ASARCO) and Kentucky Utilities are included. The Dames and Moore survey of the southeastern portion of the plant site identified one archaeological site, three standing structures and one historic cemetery. In addition 47 archaeological sites and six standing ...

Energy Technology Data Exchange (ETDEWEB)

This paper deals with the externally coal-fired combined cycle (EFCC). A process simulation for different configurations of the EFCC-process is carried out as well as an investigation of the effect of the key parameters such as the gas turbine inlet temperature and the compressor intake airflow. The results show a promising potential of the efficiency. One component of this combined gas and steam turbine cycle is a high temperature heat exchanger that has to withstand the extrem chemical and thermal operating conditions. Fibre reinforced ceramics and combinations of them with monolithic ceramics seem to be the most promising materials for this application. A cost estimating of the EFCC-process shows that a competitive operation should be possible. (orig.) [Deutsch] Die Ergebnisse der Prozesssimulationen weisen ein vielversprechendes Wirkungsgradpotential des extern kohlebefeuerten Gasturbinenprozesses auf. Der fuer dieses neue Kraftwerkskonzept notwendige Hochtemperatur-Waermetauscher ...

Energy Technology Data Exchange (ETDEWEB)

In two pilot projects Maingas AG has complemented an existing marketing mix with a telephone marketing segment. One of these telephone marketing campaigns was conducted for the purpose of `Intensification`, the other for `Activation of Unused Mains Connections`. The aim was to provide professional support to canvassing campaigns in their various phases in order to minimise diffusion losses and increase the probability of winning new customers. The slogan chosen for the drive was therefore: `Its no good being present unless one`s efficient in the preparation, execution, and revision of a campaign`. (orig.) [Deutsch] Die Maingas AG hat in zwei Pilotprojekten das bestehende Marketing-Mix durch das Segment Telefonmarketing ergaenzt. Es wurde eine Telefonmarketing-Aktion im Bereich `Verdichtung` und eine Telefonmarketing-Aktion im Bereich `Aktivierung Inaktive Hausanschluesse` durchgefuehrt. Ziel war es, durch einen professionellen flankierenden Service in den verschiedenen Phasen der ...

Energy Technology Data Exchange (ETDEWEB)

A system for partial mechanisation of the support work with roadway driving machines consisting of a crawler undercarriage carrying a selective cutter with a cutting jib on a rotary tower is claimed. The system comprises a support manipulator movable in longitudinal direction over the rotary tower and cutting jib and a preassembly table with a number of brackets to take up and preassemble a support structure consisting of profile segments, preferably an arc-shaped support with a cap made up for several parts. The system is characterized in that the preassembly table is mounted on one side of the selective cutter and has one straight vertical guide bar each for at least two cap brackets which can be continuously adjusted in height, and in that the manipulator mounted on the selective cutter has a horizontally suivelling head which may grip under the cap of the preassembled structure on the preassembly table.

Energy Technology Data Exchange (ETDEWEB)

By retrofitting the existing steam turbine dual purpose power plant with a gas turbine plant and a secondary waste heat boiler the Technische Werke Ludwigshafen AG have considerably improved the energy generation in energetic, economic and ecological terms. The extension of the existing system to a combined cycle process has lead to this positive effect. The erection of a boiler plant during the first two construction phases has fully met the optimistic expectations. (orig.) [Deutsch] Mit der Nachruestung eines vorhandenen Dampfturbinen-HKW um eine Gasturbinenanlage mit nachgeschaltetem Abhitzekessel haben die Technischen Werke Ludwigshafen AG ihre Energieerzeugung entscheidend in energetischer, oekonomischer und oekologischer Sicht optimiert. Insbesondere die Erweiterung des vorhandenen Systems zu einem GuD-Prozess fuehrt zu dieser positiven Bilanz. Die Errichtung der Kesselanlage in den ersten beiden Bauabschnitten hat die optimistischen Erwartungen voll bestaetigt. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Flow Tex and ABB Energiekabel GmbH have developed a technique which allows the recovery of cables without requiring any trenching works. The new technique was successfully used for the first time for a pilot project in 1995. The authors report on two recent recovery projects (1998) in which an optimised technology was used for recovering a total of 1 500 m system length of 110 kV low-pressure oil-filled cables in Stuttgart and Munich on very different conditions. The authors describe the operational experiences with the cable connections and highlight the background stipulating the removal of the cables. (orig.) [Deutsch] Ein Verfahren zur grabungsfreien Bergung von Kabeln, gemeinsam entwickelt von FlowTex und ABB Energiekabel, wurde erstmals in einem Pilotprojekt 1995 mit Erfolg eingesetzt. Die Verfasser berichten ueber zwei Bergungsprojekte, bei denen 1998 mit der optimierten Technik in Stuttgart und Muenchen insgesamt 1 500 Systemmeter 110-kV-Niederdruck-Oelkabel unter sehr ...

Energy Technology Data Exchange (ETDEWEB)

The austenitic nitrided Cr-Mn steels CrMnN 1812, CrMnNMo 1714 and CrNiTi 1810 has been investigated in chloride nitric acid at temperature 20-60 C. The Potentials of pitting nucleation and the time for pitting initiation has been determinate by the hronoamperometric method. It was established that alloying only with nitrogen is not sufficient procedure for obtaining of resistive to localised corrosion steel structure. Of importance for the resistance to localised corrosion of Cr-Mn steels is alloying with molybdenum. (orig.) [Deutsch] Die austenitischen stickstoffhaltigen Cr-Mn Staehle CrMnN 1812, CrMnNMo 1714 und der klassische CrNiTi 1810 wurden in chloridhaltigen Salpetersaeureloesungen im Temperaturbereich 20-60 C untersucht. Durch die hronoamperometrische Methode wurden die Potentiale der Lochfrassbildung und die Zeit zur Initiierung der Lochfrasskorrosion bestimmt. Man stellte fest, dass das Legieren der Staehle nur mit Stickstoff eine nicht genuegende Massnahme ...

Energy Technology Data Exchange (ETDEWEB)

Suppliers of systems and components for compressed air technique were shown at the Hanover Fair 94 in Hall 5. On about 6000 m{sup 2} floor area, they showed their product range, which covered the whole range of compressed air technique from compressors via equipment for providing and storing the compressed air to compressed air tools. (orig.) [Deutsch] Die Anbieter von Systemen und Komponenten fuer die Drucklufttechnik waren auf der Hannover-Messe `94 in der Halle 5 zu finden. Dort zeigten sie auf rund 6000 m{sup 2} ihre Produktpalette, die von Kompressoren ueber die Geraete zum Aufbereiten und Speichern der Druckluft bis zu Druckluftwerkzeugen reichte und den gesamten Bereich der Drucklufttechnik abdeckte. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The current discussion on worldwide climate change suggests that the current situation is unusual or extreme, and that climate changes never - or hardly ever - occurred in the centuries before. The author discusses whether this is really the case, and whether air pollution abatement measures can really help. His answers are based on the findings of palaeoclimatology. [German] Verfolgt man die Diskussion um den derzeitigen Klimawandel, so gewinnt man den Eindruck, Aussergewoehnliches und Extremes wuerde geschehen, und man bekommt zudem ueber Beratungsgremien und Medien vermittelt, dass sich in den Jahrhunderten vor dem heutigen Klimawandel das Klima nicht oder nur wenig geaendert hat. Es wird auch der Eindruck erweckt, man koenne das Klima stabilisieren und durch Emissionsminderungsmassnahmen das Klima schuetzen. Ist Klimaschutz eine loesbare Herausforderung oder ueberschaetzen wir Menschen unsere Moeglichkeiten? Man kann versuchen, sich an die Beantwortung dieser Frage heranzutasten, ...

Energy Technology Data Exchange (ETDEWEB)

Report by a participant in the International Nuclear Law School. In 2001, this advanced training course was first offered by the OECD-NEA together with the University of Montpellier and other international partners. This effort is intended to provide an overview of nuclear law, a discipline normally playing a subordinate role in curricula. In this way, a contribution is to be made to the important preservation of the existing knowledge base and to increasing know-how in this field. In 2003, the International Nuclear Law School will be continued with a new curriculum addressed to all interested participants. (orig.) [German] Erfahrungsbericht eines Teilnehmers der Internationalen Schule fuer Nuklearrecht 2002 an der Universitaet Montpellier. Erstmals im Jahr 2001 wurde diese Fortbildungsveranstaltung von der Nuclear Energy Agency der Organisation for Economic Co-operation and Development (OECD-NEA) zusammen mit der Universitaet Montpellier und weiteren internationalen ...

Energy Technology Data Exchange (ETDEWEB)

This report describes the QUEOS facility and gives the results of the first test series performed up to 6/1995. The premixing phase of a steam explosion is investigated experimentally with simulant materials. The transient three-dimensional multi-component interaction of molten corium with water is studied using a large number of small solid spheres at temperatures up to 2300 C. The objective of the experiments is to establish a data base for testing the models of heat and momentum transfer in multi-fluid codes as well as the code`s capability to correctly describe multiphase flows. The experiments have the advantage that the diameter of the `coarse melt fragments` are known and that detailed measurements can be performed without the danger of a steam explosion. In this first series of experiments up to 10 kg of spheres (max. 24000 pieces) were used. The spheres, made of molybdenum or zirconia, were heated to temperatures up to 2000 C and are discharged into 0.5 m{sup 3} of saturated ...

Energy Technology Data Exchange (ETDEWEB)

Installation of the major hardware subsystems for MFTF is nearing completion. These subsystems include the Fusion Chamber System, the eighty KV Neutral Beam System, the Superconducting Magnet System, and the Personnel Safety System. The Local Controls group has undertaken a uniform aproach to implementing the control systems for all of these hardware subsystems. This approach has two major aspects: (1) to provide a stand-alone computer control system with a remote, portable terminal so that computer control can be provided at the site of the hardware for initial testing, (2) to provide hardware simulators so that the complicated MFTF computer control system can be tested independent of the hardware. The software and hardware tools which were developed to carry out this plan will be described. Our experiences with bringing up subsystems containing up to 900 separate channels of control and status will also be described.

British Library Electronic Table of Contents (United Kingdom)

Background: While Borneo's forests are globally recognised for their diverse vegetation many regions remain uncharacterised. Aims: We examine the tree community in one hectare of lowland (hill) forest near the Malinau River. Methods: We objectively sited a 1-ha plot in primary forest. All stems over 30 cm girth were measured and identified. Results: Stem basal area was typical for Asian rain forests, but the numbers of stems (759) and species (205) were high. The most abundant species were Gluta wallichii, Cleistanthus bakonensis and Lithocarpus cantleyanus, while those contributing most to basal area were Shorea venulosa, Dipterocarpus lowii and Calophyllum lowii. Dipterocarpaceae was the dominant family amongst the largest stems and contributes a third of stand basal area (11.5 m2). Thir...

British Library Electronic Table of Contents (United Kingdom)

Soil acidification via acid precipitation is recognized to have detrimental impacts on forest ecosystems, which is in part associated with the function of ethylene released from the soil. However, the impacts of acidification on the cycling of ethylene in forest soils have not been fully taken into consideration in global change studies. Forest topsoils (0?5 cm) under four temperate forest stands were sampled to study the effects of a pH change on the emissions of ethylene and carbon dioxide from the soils and concentrations of dissolved organic carbon (DOC) released into the soils. Increasing acidification or alkalinization of forest soils could increase concentrations of DOC released into the soils under anoxic and oxic conditions. The ethylene emission from these forest topsoils could s...

Energy Technology Data Exchange (ETDEWEB)

The propagation of acoustic pressure perturbations in an adiabatic low-quality air/water flow were investigated both theoretically and experimentally. A linearized dispersion model is correlated with data to extract information on the behavior of interfacial momentum transfer controlled by the virtual volume coefficient. The dispersion model is examined in limiting cases of low and high frequency and related to current models for critical flow velocity. Fourier decomposition techniques are employed to predict the dispersion of measured pressure pulses and to relate data for standing waves and propagating pulses. The dispersion model is based on a two-fluid model and is the most complete model available in the literature at this time. The dispersion data presented herein is also the best available to date for low frequency (i.e., frequencies less than bubble resonance) sound propagation in bubbly air/water mixtures.

Energy Technology Data Exchange (ETDEWEB)

The foundation is a key to safety of any structure built on reclaimed land in coastal areas. This paper gives examples of reclamation methods, ground improvement works, foundations adopted, and consequent land subsidence as for structures directly borne by the underlying ground. Structures built on the recently reclaimed land often stand on piles driven into gravel layers. But an emphasis in pile design in usually placed on bearing capacity, with little consideration given to land subsidence and its effects. Appropriate ground improvement works, if followed by an enough consolidation period, produce satisfactory results for both direct and pile foundations. Low and light structures can be more economically built on direct foundations. It will be still safer for those structures if floating foundations or other measures are taken for preventing increases in load. 5 refs., 16 figs.

British Library Electronic Table of Contents (United Kingdom)

ABSTRACT Introduction. Postprostatectomy erectile dysfunction (ED) remains a serious quality-of-life issue. Recent advances in the understanding of the mechanism of postprostatectomy ED have stimulated great attention toward penile rehabilitation. Aim. This review presents and analyzes a contemporary series of the recent medical literature pertaining to penile rehabilitation therapy after radical prostatectomy (RP). Main Outcome Measures. The laboratory and clinical studies related to penile rehabilitation are analyzed. The validity of the methodology and the conclusion of the findings from each study are determined. Methods. The published and presented reports dealing with penile rehabilitation following RP in human and cavernous nerve injury in animal models are reviewed. Results. Exciti...

Energy Technology Data Exchange (ETDEWEB)

The detection of explosives is a notoriously difficult problem, especially at stand-off distances, due to their (generally) low vapor pressure, environmental and matrix interferences, and packaging. We are exploring optimal dynamic detection to exploit the best capabilities of recent advances in laser technology and recent discoveries in optimal shaping of laser pulses for control of molecular processes to significantly enhance the standoff detection of explosives. The core of the ODD-Ex technique is the introduction of optimally shaped laser pulses to simultaneously enhance sensitivity of explosives signatures while reducing the influence of noise and the signals from background interferents in the field (increase selectivity). These goals are being addressed by operating in an optimal nonlinear fashion, typically with a single shaped laser pulse inherently containing within it coherently locked control and probe sub-pulses. With sufficient bandwidth, the ...

British Library Electronic Table of Contents (United Kingdom)

This paper examines Pippenger's (2011) proposed solution to the forward bias puzzle, which is based on the covered interest parity (CIP) condition. It is argued that the CIP-based approach does not solve this well known and long-standing puzzle in international finance in a meaningful way. Moreover, it is shown that empirical results from such an approach follow mechanically from the identity-like nature of the theory of covered interest parity, which, aside from small deviations due to transaction costs, is assumed to hold in all periods (as if it were an identity). We show that rather than leading to new insights, the simple reconfiguration of CIP to solve for the time t+1 spot exchange rate leads to tautological expressions that, when estimated, might appear to successfully explain the ...

CERN Document Server

The ubiquitous ADE classification has induced many proposals of often mysterious correspondences both in mathematics and physics. The mathematics side includes quiver theory and the McKay Correspondence which relates finite group representation theory to Lie algebras as well as crepant resolutions of Gorenstein singularities. On the physics side, we have the graph-theoretic classification of the modular invariants of WZW models, as well as the relation between the string theory nonlinear $\\sigma$-models and Landau-Ginzburg orbifolds. We here propose a unification scheme which naturally incorporates all these correspondences of the ADE type in two complex dimensions. An intricate web of inter-relations is constructed, providing a possible guideline to establish new directions of research or alternate pathways to the standing problems in higher dimensions.

Energy Technology Data Exchange (ETDEWEB)

In this paper we describe a modelling project to improve a nuclear waste management program in charge of the creation of a new system for the permanent disposal of nuclear waste. SADT (Structural Analysis and Design Technique) is used in order to provide a work-flow description of the functions to be performed by the waste management program. This description is then translated into a number of Coloured Petri Nets (CPN or CP-nets) corresponding to different program functions where additional behavioural inscriptions provide basis for simulation. Each of these CP-nets is simulated to produce timed event charts that are useful for understanding the behaviour of the program functions under different scenarios. Then all the CPN models are linked together to form a single stand-alone application that is useful for validating the interaction and cooperation between the different program functions. A technique for linking executable CPN models is developed for supporting ...

Energy Technology Data Exchange (ETDEWEB)

Nanowires, films, and membranes comprising ordered porous manganese oxide-based octahedral molecular sieves, and methods of making, are disclosed. A single crystal ultra-long nanowire includes an ordered porous manganese oxide-based octahedral molecular sieve, and has an average length greater than about 10 micrometers and an average diameter of about 5 nanometers to about 100 nanometers. A film comprises a microporous network comprising a plurality of single crystal nanowires in the form of a layer, wherein a plurality of layers is stacked on a surface of a substrate, wherein the nanowires of each layer are substantially axially aligned. A free standing membrane comprises a microporous network comprising a plurality of single crystal nanowires in the form of a layer, wherein a plurality of layers is aggregately stacked, and wherein the nanowires of each layer are substantially axially aligned.

British Library Electronic Table of Contents (United Kingdom)

Summary: The KEGG PATHWAY database provides a widely used service for metabolic and nonmetabolic pathways. It contains manually drawn pathway maps with information about the genes, reactions and relations contained therein. To store these pathways, KEGG uses KGML, a proprietary XML-format. Parsers and translators are needed to process the pathway maps for usage in other applications and algorithms. We have developed KEGGtranslator, an easy-to-use stand-alone application that can visualize and convert KGML formatted XML-files into multiple output formats. Unlike other translators, KEGGtranslator supports a plethora of output formats, is able to augment the information in translated documents (e.g. MIRIAM annotations) beyond the scope of the KGML document, and amends missing components to fr...

Energy Technology Data Exchange (ETDEWEB)

The observed inhibition of M4 transitions in A approx. 90 nuclei has represented a long standing theoretical problem. In particular by calculating first- and second-order configuration mixing contributions to the inhibited M4 lifetimes of /sup 89/Y and /sup 87/Sr, it is found that the first-order perturbative treatment of the residual interaction usually used in shell-model calculations is unjustified in this case. Using random-phase approximation techniques, the renormalization effects of collective (''giant'') M4 resonances in /sup 88/Sr on the low energy M4 transitions in /sup 89/Y and /sup 87/Sr are investigated. It is concluded that the observed retardation of M4 lifetimes in these nuclei is consistent with the manifestation of nuclear spin polarization.

British Library Electronic Table of Contents (United Kingdom)

Graphical Abstract A Southward view of the Dead Sea western coast. The steep western escarpment of the Dead Sea basin, composed mainly of Upper Cretaceous limestone and dolomite, can be seen on the right. Beach terraces left by the shrinking lake run parallel to the shore. The larger part of the area between the present water line and the mountains was still under Dead Sea water just 50?60?years ago. The current fall of the lake?s stand is around 1?m?year?1. Three on-shore sinkholes can be seen in the front of the photo, as well as two submerged ones near its lower left corner. These were caused by dissolution of a Holocene salt layer located tens of meters below the surface, resulting in the collapse of the overlying sediments. The retreat of the Dead Sea in recent years was followed by e...

Energy Technology Data Exchange (ETDEWEB)

This article describes the chemical preparation of petroleum additives of the MASK type from samples of concentrated alkylsalicylic acids. The obtained additives contain high contents of calcium alkylsalicylate and respective total alkalinities of 156, 131, and 130 mg KOH/g. Sodium alkylsalicylate concentrates, obtained in the form of an aqueous acetone solution, were converted to alkylsalicylic acids by interaction with hydrochloric acid. The solvent was removed from the upper and lower layers by distillation, and the resulting products were analyzed by liquid chromatography. Service tests were performed on a model formulation of the additive in M-11 oil in a Petter AV-1 test stand unit in comparison with commercial MASK additive. The results indicate that the model additive formulation gives approximately the same corrected piston fouling ratings as the commercial additive.

Energy Technology Data Exchange (ETDEWEB)

An investigation of current dual-fuel natural gas/diesel engine design, performance, and emissions was conducted. The most pressing technological problems associated with dual-fuel engine use were identified along with potential solutions. It was concluded that dual-fuel engines can achieve low NOx and particulate emissions while retaining fuel-efficiency and BMEP levels comparable to those of diesel engines. The investigation also examined the potential economic impact of dual-fuel engines in diesel-electric locomotives, marine vessels, farm equipment, construction, mining, and industrial equipment, and stand-alone electricity generation systems. Recommendations for further additional funding to support research, development, and demonstration in these applications were then presented.

Energy Technology Data Exchange (ETDEWEB)

A general purpose Emergency Generator Set (EGS) is considered for a methodological study and related reliability behavior is analyzed. In particular in a procedure of reliability and availability analysis of a EGS, dependent failure events need a complex mathematical model as state-space model to be a accurately evaluated. Furthermore these dependent failure events are one of the most important reliability characteristic of EGS. This paper suggests a procedure for reliability calculations in presence of dependent failure based on the evaluation of a equivalent failure rate that can be fitted to a network reduction method by simple mathematical calculations. The simplified models analyzed show a good accuracy for a wide range of variation of main reliability characteristics of EGS and utility. The advantages obtained are very useful on reliability evaluation because the possibility of use of network approach provides a shorter route to calculation and it is applicable by a larger number ...

Energy Technology Data Exchange (ETDEWEB)

Poplar breeding in Europe is in a more advanced state than breeding programmes of other species. In Europe, poplars are part of the scenery and are integrated in the economy. Traditionally poplar stands are established in lowland areas. But an increasing interest in their use moved them to upland sites. Poplar uses are multiple: lumber, industrial wood, wind-breaks and landscape plantations, etc. Selection characteristics are classified in different groups: vegetative propagation ability, vigor, adaptation to sites and climate, resistance to diseases and insect pests, wood quality, and coppicing ability. Strategies have improved with time. The most efficient strategies for the long term involve constitution of base populations, selection of parents for intra- and interspecific hybridizations, selection within the progenies, and vegetative propagation. Short term strategies are also applied simultaneously. Advanced breeding techniques with poplars include: haploidy, ...

British Library Electronic Table of Contents (United Kingdom)

Analysis of the pattern of the chromosomal localization of quantitative trait loci (QTLs) is necessary for comprehensively understanding their functions. The chromosomal localization of QTLs controlling milk production traits has been studied in cattle chromosomes. The distribution of QTLs between chromosomes has proved to be binomial. Their distribution along each chromosome was, in general, uniform, except for the QTLs controlling the somatic cell score (SCS), which tended towards telomeric location. However, there are chromosomes either enriched with or particularly poor in QTLs. The QTL distribution patters are the most similar for the milk yield (M) and milk protein yield (P) and for milk fat yield (F) and milk fat content (%F). The pattern of the SCS QTLs stands out among those of ot...

Energy Technology Data Exchange (ETDEWEB)

The aim of this case study is to analyse the socio-economic effects of forest fuel supply and use chains. Two of the four cases are rural district heating plants. In Perho, the co-operative organisation of forest owners maintains the fuel supply and operates the plant. In Ruukki, the local forestry association supplies forest chips to the plant. These medium-scale plants use small-sized trees from young thinning stands as their main fuel. The trees are felled manually. The other two cases are large power plants. Alholmens Kraft's new power plant in Pietarsaari aim to use 250 000 solid-m3 of forest chips annually. The logging residues are hauled to the plant as bales using traditional timber harvesting equipment or as bulk material. At young thinning stands the trees are harvested using an accumulating feller buncher. The Toppila I and II power plants in the city of Oulu used about 36 000 solid-m3 of forest chips. Over 300 000 solid-m3 ...

International Nuclear Information System (INIS)

One set of hypotheses offered to explain the decline of red spruce (Picea rubens Sarg.) in eastern North America focuses on the effect of acidic deposition on soil chemistry changes that may affect nutrient availability and root function. Long-term soils data suggests that soil acidification has occurred in some spruce stands over the past 50 yr, with plant uptake and cation leaching both contributing to the loss of cations. Studies of tree ring chemistry also have indicated changes in Ca/Al and Mg/Al ratios in red spruce wood, suggesting increases in the ionic strength of soil solution. Irrigation studies using strong acid inputs have demonstrated accelerated displacement of base cations from upper horizons. Spruce-fir (Abies spp.) nutrient budgets indicate that current net Ca and Mg leaching loss rates are of the same order of magnitude as losses to whole tree harvest removals, spread out over a 50-yr rotation. For most cations, red spruce foliar nutrient levels ...

International Nuclear Information System (INIS)

Using the full potential linearized augmented plane wave (FLAPW) method, the magnetic properties of two-dimensional Ru and Rh monolayers (MLs) on a NiAl(001) surface have been investigated. It has been found that free standing one monolayer Ru and Rh films have ferromagnetic ground state with magnetic moments of 2.21 and 1.48 #mu#_B, respectively. The ferromagnetism is still observed even on a Ni terminated NiAl(001) surface, while no magnetic state is found on an Al terminated surface. The calculated magnetic moments of Ru and Rh atoms are 1.56 and 0.88 #mu#_B, respectively. In addition, an induced magnetic moment in surface Ni is observed. It has been found that the free standing Ru film has perpendicular magnetization to the film surface with a magnetocrystalline anisotropy (MCA) energy of 0.66 meV/atom, while an in-plane MCA energy of 0.37 meV/atom is achieved in Rh film. Very interestingly, we find that both Ru/NiAl(001) and Rh/NiAl(001) ...

International Nuclear Information System (INIS)

The concept of forestry-service enterprise used in the joint study (1997-7999) by the TTS-Institute and the Finnish Forest Research Institute (Metla) refers to enterprises and co-operatives (including forest workers operating as entrepreneurs) offering services in the fields of silviculture, basic forest improvement, planning and wood-harvesting sector. Companies practicing large-scale wood-conversion and traditional forestry-machine and road haulage contractors are not included in this approach. It can be estimated that there is a total of 450 such entrepreneurs in the country Those engaged in only a minor degree in providing forestry services are not included in the figure. The nation-wide research material was collected in the form of a mail questionnaire addressed to forestry-service entrepreneurs (n=320) in the spring of 1998. Almost all forestry-service entrepreneurs provide timber felling as a service. More than half of them do planting, cleaning of young ...

Energy Technology Data Exchange (ETDEWEB)

Laser-Induced Breakdown Spectroscopy was selected by NASA as part of the ChemCam instrument package for the Mars Science Laboratory rover to be launched in 2009. ChemCam's Laser-Induced Breakdown Spectroscopy instrument will ablate surface coatings from materials and measure the elemental composition of underlying rocks and soils at distances from 1 up to 10 m. The purpose of our studies is to develop an analytical methodology enabling identification and quantitative analysis of these geological materials in the context of the ChemCam's Laser-Induced Breakdown Spectroscopy instrument performance. The study presented here focuses on several terrestrial rock samples which were analyzed by Laser-Induced Breakdown Spectroscopy at an intermediate stand-off distance (3 m) and in an atmosphere similar to the Martian one (9 mbar CO{sub 2}). The experimental results highlight the matrix effects and the measurement inaccuracies due to the noise accumulated ...

Energy Technology Data Exchange (ETDEWEB)

This thesis is devoted to studies which prepared the construction of an atom Mach-Zehnder interferometer. In such an interferometer, the propagating waves are spatially separated, and the internal state of the atom is not modified. The beam-splitters are diffraction gratings, consisting of standing optical waves near-resonant with an atomic transition. We use the Bloch functions to define the atom wave inside the standing wave grating and thus explain the diffraction process in different cases. We developed a nearly all-analytical model for the propagation of an atom wave inside a Mach-Zehnder interferometer. The contrast of the signal is studied for many cases: phase or amplitude gratings, effects of extra paths, effects of the main mismatches, monochromatic or lightly polychromatic sources. Finally, we discuss three interferometric measurements we think very interesting. The first, the index of refraction of gas for atomic waves, is studied ...

Energy Technology Data Exchange (ETDEWEB)

This assessment is a feasibility study according to ISO 14024. It deals with the question whether an ecolabel is suitable for wood pellet heating systems and how concrete criteria for an ecolabel for wood pellet heating plants could be specified. The study begins with a comprehensive market analysis in order to identify possible plants for which an ecolabel would make sense. In the main part of the study, the environmental relevance of the chosen plants is analysed. For this analysis, plant manufacturers were interviewed and a comparison between wood pellet heating systems and heating systems which use gas, oil or wood was carried out. On the basis of this analysis, it was possible to derive a number of criteria which were discussed with company representatives and other experts in this field. As a result of this dialogue and the investigation process as a whole, the introduction of an ecolabel for wood pellet heating plants can be recommended. Wood pellet heating systems are ...

International Nuclear Information System (INIS)

This paper introduces examples of satellite imageries analysis and utilizations for safeguards activities. Recently, many kinds of satellite imageries are available in the world i.e., high-spatial resolution, multi- and hyper-spectral, multi-function, and multi-polarization radars. The problem is that how to obtain the required information from these digital images. The Japan Aerospace Exploration Agency (JAXA) has successfully launched the Advanced Land Observing Satellite (ALOS, the nickname is 'Daichi') on 24th January, 2006. The mission objectives are cartography, regional observation, disaster monitoring etc. ALOS has three instruments, PRISM, AVNIR-2, and PALSAR, to achieve these objectives. An overview of ALOS is provided. ALOS follows the Japanese Earth Resources Satellite- 1 (JERS-1) and the Advanced Earth Observing Satellite (ADEOS) and utilizes advanced land-observing technology. ALOS is fling in a Sun-synchronous orbit with an inclination angle of 98.16 degrees, 691.65 km ...

International Nuclear Information System (INIS)

subsequent to its in-reactor dwell time, spent fuel still contains large amounts of materials that are recoverable, for value-added energy purposes (uranium, plutonium), together with fission products, and minor actinides, making up the residues from nuclear reactions. The treatment and recycling of spent nuclear fuel, as implemented in France, entail that such materials be chemically partitioned. The development of the process involved, and its deployment on an industrial scale stand as a high achievement of French science, and technology. Treatment and recycling allow both a satisfactory management of nuclear waste to be implemented, and substantial savings, in terms of fissile material. Bolstered of late as it has been, due to spectacularly skyrocketing uranium prices, this strategy is bound to become indispensable, with the advent of the next generation of fast reactors. This Monograph surveys the chemical process used for spent fuel treatment, and its ...

Energy Technology Data Exchange (ETDEWEB)

The increased demand for renewable energy sources has led to large areas of former agricultural land being proposed for short rotation coppice (SRC) establishment. Concerns expressed over the potential impacts of tree roots on buried archaeological evidence led to a study into the rooting habit of SRC. Roots were exposed in trenches dug within a variety of willow and poplar clonal stands grown on brown earth, pelosol, ground-water gley and surface-water gley soils. Root depths and diameters were recorded in each of the 33 trenches. In total, over 18,000 roots were measured on 264 coppice stools. The rotation length, species and stool location within a block were all found to influence the maximum size of root produced. Soil type had some influence on the root number and depth, but the pattern of root distribution down the soil profile was similar for both species. (author)

Science.gov (United States)

The Wind Energy Research Division of Sandia National Laboratories has been funded by the Wind/Ocean Technology Division of the Department of Energy (DOE) to design and build a 34-meter diameter Vertical Axis Wind Turbine (VAWT). The turbine design incorporates the results of recent VAWT research in aerodynamics and structural dynamics. Initial system concept studies identified several blade options that met the required power rating of 500 kW. The final blade and rotor configurations were chosen based on finite element calculations that determined the turbine modes of response, their frequency of vibration, and stress levels. For parked survival turbine components were designed to with stand the loading of a 150 mph (67.0 m/s) wind coupled with maximum cable tensions. Specific areas of design discussed include the rotor, cables, bearings, brakes, and foundations. Construction of the turbine is in progress at this time and anticipated completion of the project is ...

Energy Technology Data Exchange (ETDEWEB)

There are two versions of the MORSE multigroup Monte Carlo radiation transport computer code system at Oak Ridge National Laboratory. MORSE-CGA is the most well-known and has undergone extensive use for many years. MORSE-SGC was originally developed in about 1980 in order to restructure the cross-section handling and thereby save storage. However, with the advent of new computer systems having much larger storage capacity, that aspect of SGC has become unnecessary. Both versions use data from multigroup cross-section libraries, although in somewhat different formats. MORSE-SGC is the version of MORSE that is part of the SCALE system, but it can also be run stand-alone. Both CGA and SGC use the Multiple Array System (MARS) geometry package. In the last six months the main focus of the work on these two versions has been on making them operational on workstations, in particular, the IBM RISC 6000 family. A new version of SCALE for workstations is being released to ...

British Library Electronic Table of Contents (United Kingdom)

Abstract This research aimed to investigate coarse root systems of Jarrah (Eucalyptus marginata Donn ex Sm.) trees at a 13-year-old restored bauxite mine site in south-western Australia. Excavations in an area with small trees (low-quality site) revealed that deep ripping equipment failed to penetrate the cemented lateritic subsoil, restricting coarse roots (roots >5 mm in diameter) to the top 0.5 m of the soil profile, resulting in fewer (1,344 stems/ha) and smaller (mean height 4.5 m) Jarrah trees. An adjacent area within the same pit (high-quality site), with a stand density of 3,256 stems/ha and a mean height of 8.0 m, had a kaolinitic clay subsoil which coarse roots penetrated to the average ripping depth (1.5 m). Trees at the low-quality site did not penetrate the subsoil with their ...

Energy Technology Data Exchange (ETDEWEB)

Fabrication of diffused titanium optical guides on a LiNbO/sub 3/ crystal substrate requires precise quality assurance. Light couplers in particular must be positioned within micron specifications. This requirement is the reason that the width of lines detected during microscopic inspection of the crystal is such an important parameter for quality evaluation. To assist in the inspection of these optical guides, a line width estimation program has been developed for an IBM PC based microscope inspection system. A digital image processing approach is used to develop an algorithm which can be tailored by the user for specific signal and noise characteristics. Default filter parameters, which can be updated and saved interactively by the user, are stored in a file on disk. The final program can be executed stand-alone or through a commercially available, menu-driven, image processing software package. Details concerning the implementation of this program are presented ...

International Nuclear Information System (INIS)

Neutron radiography is a non-destructive test method to examine a material by using the dependency of neutron attenuation on the nuclear characteristics of the atoms composing the object material. There are two categories of neutron radiography; static neutron radiography and dynamic neutron radiography. The static neutron radiography is a technique to observe a standing object by using a camera or a film cassette. The dynamic neutron radiography(DNR) is a technique to observe a moving object usually by using a camera. Depending on the camera frame rate, the dynamic neutron radiography is categorized into the real time neutron radiography(RTNR) and the high speed neutron radiography(HSNR). The frame rate for RTNR is 30 frames/s and that for HSNR is usually more that 500 frames/sec. Thus, RTNR is good for observing time-averaged phenomena and HSNR is good for observing instantaneous phenomena. DNR is a powerful tool for fluid visualization as well as the multi-phase ...

International Nuclear Information System (INIS)

Purpose: In an experimental study, the correlation between the trabecular bone density of the different regions of the proximal femur and the fracture load in the setting of femoral neck fractures was examined. Methods: The bone mineral density 41 random proximal human femora was estimated by single-energy quanitative CT (SE-QCT). The trabecular bone density was measured at the greatest possible extracortical volume at midcapital, midneck and intertrochanteric level and in the 1 cm"3 volumes of the centres of these regions in a standardised 10 mm thick slice in the middle of the femoral neck axis (in mg/ml Ca-hydroxyl apatite). The proximal femora were then isolated and mounted on a compression/bending device under two-legged stand conditions and loaded up to the point when a femoral neck fracture occurred. Results: Statistical analysis revealed a linear correlation between the trabecular bone density and the fracture load for the greater regions, with the highest ...

Energy Technology Data Exchange (ETDEWEB)

This proceedings is the compilation of papers presented at the ninth PV Performance and Reliability Workshop held at the Sheraton Denver West Hotel on September 4--6, 1996. This years workshop included presentations from 25 speakers and had over 100 attendees. All of the presentations that were given are included in this proceedings. Topics of the papers included: defining service lifetime and developing models for PV module lifetime; examining and determining failure and degradation mechanisms in PV modules; combining IEEE/IEC/UL testing procedures; AC module performance and reliability testing; inverter reliability/qualification testing; standardization of utility interconnect requirements for PV systems; need activities to separate variables by testing individual components of PV systems (e.g. cells, modules, batteries, inverters,charge controllers) for individual reliability and then test them in actual system configurations; more results reported from field experience on modules, ...

Energy Technology Data Exchange (ETDEWEB)

Simulations and experiments have been carried out to explore using a plastic scintillator as a dosimetry probe in the vicinity of a pulsed bremsstrahlung source in the range 4 to 20 MeV. Taking advantage of the tissue-equivalent properties of this detector in conjunction with the use of a fast digital signal processor near real-time dosimetry was shown to be possible. The importance of accounting for a broad energy electron beam in bremsstrahlung production, and photon scattering and build-up, in correctly interpreting dosimetry results at long stand-off distances is highlighted by comparing real world experiments with ideal geometry simulations. Close agreement was found between absorbed energy calculations based upon spectroscopic techniques and calculations based upon signal integration, showing a ratio between 10 MeV absorbed dose to 12 MeV absorbed dose of 0.66 at a distance of 91.4 m from the accelerator. This is compared with an idealized model simulation ...

Energy Technology Data Exchange (ETDEWEB)

Modern oscillation- and analysis systems are often mentioned in the context of oscillation diagnosis which implies that this is a method of establishing the causes of the mechanical changes that cause the unwanted oscillation. Experience shows, however, that oscillation monitoring instruments can merely indicate oscillation symptoms at an early point in time. These findings must be interpreted in a machine-specific way and seen in the context of previous developments in order to establish the mechanical root cause of the matter. A 1000 MVA-generator shows that conventional oscillation measuring systems may also serve for diagnostic purposes within certain limits.(orig.) [German] Im Zusammenhang mit modernen Schwingungsmess- und Analysensystemen wird haeufig der Begriff der Schwingungsdiagnose verwandt und inpliziert, damit auch die Ursache von mechanischen Veraenderungen finden zu koennen, welche das beanstandete Schwingungsverhalten hervorruft. In der Praxis zeigt sich, dass dem ...

Energy Technology Data Exchange (ETDEWEB)

Coded imaging techniques using thick, micro-Fresnel zone plates as coded apertures have been used to image x-ray emissions (2-20 keV) and 3.5 MeV Alpha particle emissions from laser driven micro-implosions. Image resolution in these experiments was 3-8 ..mu..m. Extension of this coded imaging capability to higher energy x-rays (approx. 100 keV) and more penetrating charged particles (e.g. approx. 15 MeV protons) requires the fabrication of very thick (50-200 ..mu..m), high aspect ratio (10:1), gold Fresnel zone plates with narrow linewidths (5-25 ..mu..m) for use as coded aperatures. A reactive ion etch technique in oxygen has been used to produce thick zone plate patterns in polymer films. The polymer patterns serve as electroplating molds for the subsequent fabrication of the free-standing gold zone plate structures.

International Nuclear Information System (INIS)

Micronutrient deficiencies in flooded rice have been recognized with increasing frequency in recent years. Zinc deficiency is the most widespread disorder, followed by Fe, Mn, and Cu deficiencies. Boron and Mo deficiencies have not been reported in field culture. The peculiar characteristics of a flooded soil are: 1) a layer of standing water; 2) absence of oxygen; 3) a soil profile largely in a reduced chemical state; 4) the presence of large biological carbon dioxide excesses; 5) the presence of high concentrations of soluble Fe"+"+ and Mn"+"+; 6) alteration of soil pH; 7) the presence of toxic substances; 8) increased soluble Na"+, K"+, Ca"+"+, Mg"+"+, NH_4"+, HCO_3"-, H_2PO_4"-, and Si(OH)_4 in the soil solution. Micronutrient availability in flooded soils is affected by: 1) increased solubility of relatively insoluble minerals due to dilution effects; 2) pH changes in relation to solubility and plant availability; 3) changes in oxidation-reduction equilibria; ...

Energy Technology Data Exchange (ETDEWEB)

The most recently developed control technologies in a hot strip mill are described. Preview AGC has been developed with a preview control synthesis. It controls roll gaps by using the previous information of disturbances. The disturbances which are concerned are derived from the rolling force, the roll gap and the thickness of a previous stand. The thickness accuracy and the availability of mill have been improved by this technology. An on-line roll grinding (ORG) system with an on-line roll profile meter (OPM) has been developed for the purpose of achieving schedule-free rolling. The ORG smooths the worn and roughed surface of a work roll and OPM can measure the profile of a revolving roll without contact. The data obtained by the OPM are given as feedback information to the ORG. As a result, grinding accuracy has been improved and rolling restriction on width has been relaxed widely. (author)

Science.gov (United States)

We presented a simple approach for in-situ synthesis of poly(dimethylsiloxane) (PDMS)-gold nanoparticles composite film based on the special characteristics of PDMS itself. It is an environmentally safe synthesis method without the requirement of additional reducing/stabilizing agents. The region where the resulting gold nanoparticles distribute (in the matrix or on the surface of the polymer) and the size of the nanoparticles, as well as the colour of the free-standing films, can be simply controlled by adjusting the ratio of curing agent and the PDMS monomer. The chemical and optical properties of these composite films were studied. Using such a method, gold nanoparticle micropatterns on PDMS surfaces can be performed. And based on the gold nanoparticles micropattern, further modification with antibodies, antigens, enzymes and other biomolecules can be achieved. To verify this ability, an immobilized glucose oxidase (GOx) reactor in microchannels was built and ...

International Nuclear Information System (INIS)

Fundamentals of klystron testing is a text primarily intended for the indoctrination of new klystron group test stand operators. It should significantly reduce the familiarization time of a new operator, making him an asset to the group sooner than has been experienced in the past. The new employee must appreciate the mission of SLAC before he can rightfully be expected to make a meaningful contribution to the group's effort. Thus, the introductory section acquaints the reader with basic concepts of accelerators in general, then briefly describes major physical aspects of the Stanford Linear Accelerator. Only then is his attention directed to the klystron, with its auxiliary systems, and the rudiments of klystron tube performance checks. It is presumed that the reader is acquainted with basic principles of electronics and scientific notation. However, to preserve the integrity of an indoctrination guide, tedious technical discussions and mathematical analysis have ...

Energy Technology Data Exchange (ETDEWEB)

Pre-stacking depth migration treatment is studied for the estimation of the fold configuration from seismic survey cross sections. The estimation of a velocity structure is necessary for the execution of such treatment, and the utilization of structural-geological knowledge is required for its interpretation. The concept of balanced cross section in relation to the fault-bend fold constructs a stratum structure model under conditions that the deformation during fold and fault formation is a planar strain, that there is no change in volume due to deformation, and that a fold is a parallel fold. In addition to the above geometric and kinetic approach, there is another fold formation process simulation model using a Newtonian fluid for study from the viewpoint of dynamics. This simulation stands on the presumption that the boundary contains a ramp that had been in presence before fold formation and that an incompressible viscous matter is mounted on the top surface. ...

Science.gov (United States)

One of the energy-saving devices used on gas cooking appliances to eliminate the standing pilot is a spark ignition system. For safety, an ignition system must start promptly and be active whenever flowing gas is not ignited. To minimize noise and nuisance shock hazard, ignition must occur quickly and the sparking must be stopped as soon as ignition occurs and remain off as long as the flame is present. To accomplish both of these requirements, ignition systems have been devised which use the electrical current rectification property of a flame to sense it. These systems spark whenever the gas valve is on and a flame is not present. The factors affecting the performance of a spark ignition system are numerous, complex, and transient. All of these properties make quantification of performance difficult. A system is described which can evaluate the overall performance of ignition systems over significant periods of time and varieties of operating conditions and ...

International Nuclear Information System (INIS)

The effects of focused-ion-beam (FIB) irradiation on writer performance were examined on a perpendicular recording system. The entire top pole was irradiated by FIB with ion doses from 0 to 300 pC/#mu#m"2. PW_5_0 and signal to noise ratio (SNR) were characterized using a spin stand before and after FIB irradiation. It was found that there is degradation of PW_5_0 and SNR due to FIB irradiation. At the maximum dose (300 pC/#mu#m"2), PW_5_0 increased by 33 nm (>30%) and SNR decreased by 5 dB (>25%). The degradation was attributed to the physical pole tip recession and the formation of a magnetic dead layer. The thickness of the magnetic dead layer was estimated by analyzing the write spacing loss. Using atomic force microscopy and stage current change monitored during FIB process, it was found that the entire 4-nm protective carbon layer was etched away with a dose of 25 pC/#mu#m"2. This result implies that the degradation with ion doses <25 pC/#mu#m"2 is ...

CERN Document Server

We consider the framework of an operator-valued noncommutative probability space over a unital C*-algebra B. We show how for a B-valued distribution \\mu one can define convolution powers with respect to free additive convolution and with respect to Boolean convolution, where the exponent considered in the power is a suitably chosen linear map \\eta from B to B, instead of being a non-negative real number. More precisely, the Boolean convolution power is defined whenever \\eta is completely positive, while the free additive convolution power is defined whenever \\eta - 1 is completely positive (where 1 stands for the identity map on B). In connection to these convolution powers we define an evolution semigroup related to the Boolean Bercovici-Pata bijection. We prove several properties of this semigroup, including its connection to the B-valued free Brownian motion. We also obtain two results on the operator-valued analytic function theory related to the free ...

Energy Technology Data Exchange (ETDEWEB)

In the last few years the supercharging of Otto-cycle-engines has regained popularity, as demonstrated by a number of series-production engines. After listing the aims to be met by a modern supercharger the paper describes the technical status of mass-produced or close to production superchargers. This is followed by a comparative evaluation of the systems, enabling the reader to select possible solutions for a projected supercharger-engine-system by means of a comparison chart. The paper is concluded by a list of possible directions for further development and additional potential for twin-screw superchargers. (orig.) [German] In neuerer Zeit hat die Aufladung von Ottomotoren wieder ein verstaerktes Interesse gefunden, das sich auch in einer Anzahl serienmaessig gefertigter aufgeladener Motortypen wiederspiegelt. Der vorliegende Beitrag beschreibt, nach einer Darstellung der Anforderungen an ein modernes Aufladegeraet, den Stand der Technik bei serienmaessigen ...

Energy Technology Data Exchange (ETDEWEB)

Recently, the capabilities of the CORMLT code, which was designed to predict heatup, degradation, and meltdown of core and Reactor Pressure VEssel (RPV) internals during postulated severe accidents, were enhanced to enable tracking of individual fission product species during core meltdown. In addition, a mechanistic treatment of the release and flow of molten materials was developed to replace the engineering models developed earlier. In the present paper, the improved models are described and predictions of melt progression for a postullated accident sequence (TMLB') are discussed. A key issue in the new modeling is the mechanical behavior of fuel pellet stacks during run-off of molten cladding. One view is that capillary forces result in ''welding'' of porous fuel, thereby promoting free-standing pellet stacks; another is that rubblization and slumping of fuel take place. Results are reported for the first view point ...

International Nuclear Information System (INIS)

We describe a panoramic stigmatic spectrograph comprising a grazing-incidence toroidal mirror and a large-aperture free-standing transmission diffraction grating (5000 lines mm-1 ). Two spectrograph versions were constructed, with grazing angles of 7.6 and 40 and the short-wavelength spectral limits near 4 and 1.5 nm. The spectrograph aberrations were studied by numerical ray tracing. The spectrograph was used to record line and quasi-continuous spectra (1.5 - 30 nm) of multiply charged ions in a plasma generated by the second-harmonic pulses of an yttrium aluminate laser (Q = 0.15 J, ? = 5 ns, ? = 0.54 ?m, repetition rate = 0.5 Hz). In combination with a laser-produced plasma radiation source, the arrangement was used to characterise soft x-ray optical components and to generate collimated beams of polarised radiation in the 14 - 20 nm range. (laser applications and other topics in quantum electronics)

Science.gov (United States)

The provincial ministry of health has taken over a dialysis center in La Plata, Argentina, following the discovery that at least 20 of the clinic's 34 regular patients have been infected with the human immunodeficiency virus (HIV). Catheters of the clinic's dialysis machines were found to be contaminated with HIV. The 5 physicians associated with the Centro Modelo de Dialisis have been discharged for negligence. 20 of the regular patients also contracted hepatitis C. Argentinian law stipulates that filters for the same patient must be changed after 4 times and prohibits the use of the same vessel to administer medication to more than 1 patient. Testimony from nurses at the La Plata clinic revealed that filters were reused for several patients and basic sanitary procedures were not followed. In 1990, 33 kidney disease patients at a dialysis center in Cordoba became infected with HIV and it was discovered that filters had been used up to 8 times for different patients. The 5 La ...

Energy Technology Data Exchange (ETDEWEB)

Aluminum matrix composite Al356/SiCp(Vol. 15%)(Al MMC) material has been cut under various cutting conditions using Abrasive WaterJet (AWJ) machining process. The experimental cutting was carried out using three different material thicknesses of 10, 20, 30mm with a 0.33mm diameter orifice. The pump pressure, traverse rate, StandOff Distance(SOD) were taken as process parameters. After cutting the quality of the specimen in terms of kerf width, kerf taper, and surface finish were measured to characterize machinability of the material. As a result of the study, the maximum traverse rate for 30mm thick Al MMC under the pump pressure of 350 MPa reached up to 70 mm/min and the surface roughness of the material showed surface finish Ra in the range of 2.3{approx}23.4{mu}m.

International Nuclear Information System (INIS)

This paper presents a spatial gaming model with price caps for deregulated electricity markets. There has been heated debate on price caps that have been enforced in deregulated electricity markets. Opponents argue that price caps may send wrong economic signals while advocates argue that price caps are good for damping market power. This paper does not intend to take a stand in the argument. Given the fact that price caps are enforced in several deregulated regional electricity markets in the US, a logical step is to reflect this reality in gaining modeling. However, current gaining models have not included any price cap formulation. This paper is the first one to address the issue. DC power flow equations are used for representing the spatial nature of an electrical network. An algorithm is proposed to find a generalized Nash equilibrium under the enforcement of price caps based on the Kuhn-Tucker Vector Optimization Theorem. Case studies show the successful ...

Energy Technology Data Exchange (ETDEWEB)

This update of a system concept entitled ``Maritime hazard prevention and water protection`` makes full use of the technical room for maneuver while considering that reasonable financial and economic conditions must be provided. The update allows on to continue or start the exploitation of feasible technical, logistic and information-technology development potentials. The same applies to the national maritime traffic safety measures developed for the German waterways. Considering the maritime hazards that have been prevailing in the coastal areas of the German North Sea, the conducted damage risk investigations suggest that a large-scale, disastrous oil contamination of the mud flats ecosystem cannot be excluded or controlled definitely in spite of the numerous measures taken. (orig.) [Deutsch] Mit der vorgelegten Fortschreibung zum Systemkonzept ``Gefahrenabwehr und Gewaesserschutz im Seeverkehr`` werden die technisch realisierten Handlungsspielraeume unter ...

Energy Technology Data Exchange (ETDEWEB)

This is a report on the results of creep tests of large extent on samples of welded joints. The possibilities of minimising the reduction in creep strength which occurs are also shown. The range of the pipe welded joints examined extends from superheater pipes 31.8 diam x 5 mm to hot steam pipelines 240 diam x 29 mm. The steels used are: X 20 CrMoV 12-1, X 10 CrMoVNb 9-1 and X 10 CrWMoVnB 9-2. (orig./MM) [Deutsch] Es wird ueber Ergebnisse von in groesserem Umfang laufenden Zeitstandversuchen an Proben aus Schweissverbindungen berichtet. Ausserdem werden Moeglichkeiten aufgezeigt, den eintretenden Zeitstandfestigkeitsabfall zu minimieren. Die Spanne der in Untersuchung befindlichen Rohrschweissverbindungen reicht dabei vom Ueberhitzerrohr diameter 31,8 x 5 mm bis zum Heissdampfleitungsrohr diameter 240 x 29 mm. Die verwendeten Staehle sind: X 20 CrMoV 12 -1; X 10 CrMoVnB 9-1; X 10 CrWMoVnb 9-2. (orig./MM)

Energy Technology Data Exchange (ETDEWEB)

The objective of the project was to develop an infiltration material based on SiC that should have improved corrosion resistance and should permit higher operating temperatures. From a variety of tested doping agents, zirconium silicide and molybdenum proved to be the most appropriate agents. The respective infiltration materials permit a combination of advantages of the SSiC with those of the SiSiC. Silicide SiC, analogous to the SiSiC, is almost nonshrinking, and above all is more corrosion-resistant than SiSiC in the alkaline regime, due to the replacement of free silicon by silicide phases. The operating temperature of the molybdenum-base variant is 1600 C. (orig./CB) [Deutsch] Ziel des Vorhabens war die Entwicklung eines Infiltrationswerkstoffes auf SiC-Basis mit verbesserter Korrosionsbestaendigkeit und hoeherer Einsatztemperatur. Aus einer Vielzahl von getesteten Dotierungsmoeglichkeiten kristallisierten sich Zirkondisilicid und Molybdaen als geeingete Zusaetze heraus. Die ...

Energy Technology Data Exchange (ETDEWEB)

With the development of the latent heat store and its inclusion in the conventional heating control of cars, success has been achieved both in increasing comfort and in making an important contribution to safety of driving. Great store is set in development of the system on its environmental friendliness, for example by the thorough use of environmentally friendly and reusable materials. This also means the use of clean materials. It was shown that the latent heat store (apart from the aspects of comfort and safety of driving) can also make a contribution to saving fuel and reducing the exhaust gas. The sum total of the advantages makes it clear that the latent heat store introduced here is a very environmentally friendly system with multi-functional properties. (orig.) [Deutsch] Mit der Entwicklung des Latentwaermespeichers und seiner Einbindung in die konventionelle Heizungsregelung von Automobilen ist es gelungen, sowohl den Komfort deutlich zu erhoehen als auch einen wichtigen ...

Energy Technology Data Exchange (ETDEWEB)

As one of the largest contractors for the construction of ethylene plants featuring steam cracker furnaces as their core component Linde AG has examined the `real` chemical recycling of polymers in steam cracker furnaces as an alternative to their thermal utilisation. In steam cracker furnaces the feedstock, i.e., hydrocarbons, is broken down to ethylene, propylene, and other valuable products in a steam dilution of approx. 800-870 C. In the ideal case, if polyolefins are used as feedstock, then the initial product which led to the polymers can be fully recycled. In this context a series of experiments was carried out in a laboratory-scale cracker plant. The purpose of this was to demonstrate the technical feasibility and the economic advantage of using recycling polyethylene or polypropylene as feedstock for steam cracker plants. (orig./SR) [Deutsch] Die Linde AG als einer der bedeutendsten Kontraktoren fuer den Bau von Ethylenanlagen, deren Herzstueck die Steamcrackeroefen sind, hat ...

Energy Technology Data Exchange (ETDEWEB)

Osteonecrosis (ON) of the hip joint remains an unsolved therapeutical problem. Diagnosis of ON of the hip has been improved by the technical progress of imaging modalities and better understanding pathomorphology. Over a long period only plain radiographs have been available. Scintigraphy and computed tomography contributed to differential diagnosis and early detection of bone necrosis. Diagnosis in an early reversible stage is of importance. Understanding of pathophysiology, early diagnosis and therapeutical approach has been significantly improved by MR imaging. Using the ARCO system all imaging modalities and their diagnostic viability are described in the five ARCO stages. At the end a diagnostic algorithm will be proposed. (orig.) [German] Die Osteonekrose des Hueftgelenks (ON) stellt noch immer ein nicht geloestes therapeutisches Problem dar. Die diagnostischen Moeglichkeiten bei der ON wurden in den letzten Jahren durch technische Fortschritte bei den bildgebenden Verfahren und ...

Energy Technology Data Exchange (ETDEWEB)

For location of leakage at district heating pipelines several techniques are available today. If there is no wire bound lead monitoring system installed, the DH company has to apply mobile methods for detection and location and if possible characterization of leakage. Most mobile methods available today are restricted in application and often they cause supply disconnections, especially the location of very small leaks is difficult. The Institute for Environmental, Safety and Energy Technology (UMSICHT) has tested a new developed method that can be executed by own employees of DH companies that can be realised parallel to normal supply mode, and that is able to locate and characterize even very small leakages. (orig.) [Deutsch] Zur Lecksuche an Fernwaermeleitungen stehen verschiedene Techniken zur Verfuegung. Wurde beim Bau der Fernwaermetrasse kein drahtgebundenes Ueberwachungssystem eingebaut, ist der Netzbetreiber auf mobile Lecksuchmethoden angewiesen. Die herkoemmlichen mobilen ...

Energy Technology Data Exchange (ETDEWEB)

A high-temperature flow reactor and different technical plants were tested within the framework of this research project. Anthropogenic N{sub 2}O emissions form during secondary flue gas or waste gas purification as secondary emissions during denitrification and pollution abatement measures. N{sub 2}O forms as an intermediate product as NO is reduced to N{sub 2}. Under certain operating conditions N{sub 2}O is not decomposed completely. Different secondary flue gas purification measures, i.e. selective noncatalytic reduction (SNCR), selective catalytic reduction (SCR), and nonselective catalytic reduction (NSCR) were investigated testing several technical plants and the high-temperature flow reactor. (orig./EF) [Deutsch] Das Forschungsprojekt ``Messung der N{sub 2}O-Emissionen von Verbrennungsanlagen und Untersuchung von Moeglichkeiten zur Emissionsminderung`` wurde an einem Hochtemperatur-Stroemungsreaktor und an verschiedenen technischen Anlagen durchgefuehrt. Das anthropogen ...

Energy Technology Data Exchange (ETDEWEB)

The book is a German translation of an American textbook with the original title ''MRI Survival Guide'' and is intended to serve as an introductory guide for beginners or a reference book for quick information. Readers will find information on the fundamentals of the technology and methodology of MRI as well as all details of relevance to practice in a precise and easy-to-grasp arrangement, covering all anatomic areas of interest, illustrations and descriptions of characteristic signs of pathologic processes, high-quality and unusually large-sized diagnostic pictures, a modern didactic concept for quick orientiation, including surveys, tables, and reproductions for visualisation of contents. (orig./CB) [German] Praktisch jeder Mediziner wird im Laufe seiner Berufstaetigkeit mit der MRT konfrontiert - unabhaengig davon ob in der Radiologie, Orthopaedie, Gynaekologie, Chirurgie, Neurologie oder sonstigen Fachrichtung. Das Buch ist eine Uebersetzung ...

Energy Technology Data Exchange (ETDEWEB)

The composition of alkaline and neutral boric acid containing evaporator concentrates resulting from the treatment of radioactive waste water in nuclear power plants with WWER reactors is described as well as the processing of these concentrates to a product suitable for final disposal. Tests with mock solutions of these evaporator concentrates have been performed at the laboratory and teststand scale to produce a dry residue by continuous thickening, which can be processed into a highly leach resistant product, suitable for final disposal, by cementation. Ca-compounds must be added to the evaporator concentrates prior to the drying in an rotary thin-film evaporator (RTFE). The tests showed that neutral evaporator concentrates can be dried in a RTFE with addition of small amounts of Ca-compounds. The alkaline evaporator concentrates with high boric acid and total salt load require a multiple amount of Ca-compounds and diluting water to perform the drying process. A brief description of ...

Energy Technology Data Exchange (ETDEWEB)

Alloyed steels containing retained austenite after martensitic hardening are widely applied in technical practice. Although many practical investigations have been made into the mechanical behaviour of composite microstructures with retained austenite, there is still a lack of knowledge concerning their fatigue and crack propagation behaviour. For this reason, the author investigated the effects of retained austenite concentration and stability on the transformation and deformation behaviour of hardened states of the steels X210Cr12 and 100Cr6. For this purpose, monotone tensile tests, cyclic tensile pressure tests, and supplementary crack propagation experiments were carried out. The concentrations of retained austenite were varied between 10 and 100% by volume by means of different heat treatments. [Deutsch] Legierte Staehle, die nach martensitischer Haertung noch Restaustenit enthalten, finden in der technischen Praxis verbreitete Anwendung. Zum mechanischen ...

Energy Technology Data Exchange (ETDEWEB)

In addition to dependable starting - even at extreme sub-zero temperatures - the starting behaviour of modern commercial vehicle diesel engines is increasingly being evaluated on the basis of HC emissions in the starting and warm-up phases. To improve their performance in this respect, most small and medium-sized diesel engines (with a capacity of 3 to 12 litres) are therefore equipped with intake air heating systems. As an alternative to high-performance, fuel-burning flame start systems, the automotive industry supplier Beru has now developed a new type of self-regulating electric heating element which not only ensures dependable starting with short heating times but also allows drastic reductions in HC emissions. (orig.) [Deutsch] Das Startverhalten moderner Nutzfahrzeug-Dieselmotoren wird, ergaenzend zum Hauptmerkmal des sicheren Starts auch bei extremen Minustemperaturen, zunehmend anhand der HC-Emission in der Start- und Warmlaufphase beurteilt. Zur ...

Energy Technology Data Exchange (ETDEWEB)

Due to the 'novel forest diseases' the political parties of the Federal Republic of Germany unanimously attend to the reduction of emissions. The transportation sector is considered to be a major emission source. A study discussed in the publication abstracted did therefore aim at giving a detailed account and description of the recently ratified technical requirements and tax credits expected to reduce vehicle exhaust gas air pollution. Moreover, the study researches into the regulations' importance as to the low emission properties of individual automobiles. Based on the results obtained the study arrives at assumptions as to emissions to be expected from the transportation sector. It tries to assess the financial import with respect to the individual citizen, overall internal revenues and federal motor vehicle taxes. The introductory chapter is followed by a review of emissions caused by vehicle exhaust gases along with a description of their historical ...

Energy Technology Data Exchange (ETDEWEB)

The `biotechnology 2000` project is supervised by the project sponsor `biology, energy, ecology` at Forschungszentrum Juelich on behalf of the Federal Ministry for Research and Technology. The project activities cover the development of techniques and methods, cell biology, gene structure and gene regulation, photosynthetic production processes, biological hydrogen production, synthetic biology, protein design, neurobiological research, biosystems, plant breeding, phytomedicine and plant protection, the biology of waste disposal methods, research into methods which replace animal experiments, biological safety research, technology risk assessment, and ethical aspects. A general survey introduces the promoted projects, and standardized data sheets briefly introduce the individual activities. The appendix gives the project indices, the indices of joint projects, a list of the supported companies and institutions, and the project sponsor flowsheet. (orig.) [Deutsch] Das Programm ...

Energy Technology Data Exchange (ETDEWEB)

Purpose: To evaluate the success rates of the implantation of stent grafts in the treatment of peripheral aneurysms. Materials and methods: in 13 patients with 15 aneurysms at the common iliac artery (n = 6), external iliac artery (n = 1), hypogastric artery (n = 2), femoral artery (n = 2) or popliteal artery (n = 4), implantation of dacron-covered nitinol stents was performed. The patients were followed up for three to 20 months (mean, 8.8 months) with intravenous digital subtraction angiography, CT or colour-coded Doppler sonography. Results: In all cases, the aneurysm was successfully occluded after stent implantation. In one case with a popliteal aneurysm, kinking of the vessel caused thrombosis of the stent. The stent was successfully reopened. The aneurysm however, had to be surgically treated 9 months later. The primary and secondary patency rates at 6 months were 93% and 100%, respectively. Conclusion: The method described might be an alternative therapy to surgery. There are ...

Energy Technology Data Exchange (ETDEWEB)

Characterisation of the classification of brain tumours authorised by the WHO. Method of appraisal: This classification was revised and published in its second version. In the revision, some tumours were regrouped histogenetically and some tumour variants were added. Radiologically relevant changes of the classification include the differentiation of four new tumour entities that are easily distinguished by MR imaging. These four tumours belong to the group of childhood tumours or tumours occurring in early adulthood and are characterized by a good prognosis after extirpation. Results of appraisal: Central neurocytomas are small-cyst ventricular tumours associated with the foramen of Monroi and show moderate contrast enhancement. Infantile desmoplastic gangliogliomas/astrocytomas commonly consist of a solid tumour portion related to the leptomeninges with pronounced contrast enhancement and a typically very large cyst. Pleomorphic xanthostrocytomas are circumscribed cortical tumours ...

Energy Technology Data Exchange (ETDEWEB)

A singular stress field can occur at the edge of the joint plane in a thermally or mechanically loaded material compound. This stress field was calculated analytically and was compared with the results from the finite element method. If one of the two partners consists of ceramic material, unstable crack spread starting from faults in this strongly stressed area can lead to failure. In linear elastic material, the behaviour of a crack is clearly described by the stress intensity factors. These can be calculated for a known stress distribution in the uncracked structure by the method of the weight function. The corresponding weight functions for surface cracks parallel to the boundary surface were determined with the aid of suitable reference load cases. The effect of the position of the crack in the compound and the elastic constants of the compound are discussed. For examples, the stress intensity factors for cracks in a thermally stressed material compound were determined by the ...

Energy Technology Data Exchange (ETDEWEB)

Nickel-based alloys are presently used as brazing filler metals for components which undergo mechanical stress in corrosive conditions, f. e. heat exchangers. When soldering chrome containing steel parts with nickel based brazing filler metals additionally containing boron and silicon a reaction of chrome and boron can occur. This evolution of chromium borides, depositing on grain boundaries, causes a lack of chrome in the steel part. A drop of the chrome content in the parts below 13 % leads to a loss of corrosion resistance. It is possible to change the microstructure of brazing joints by modification with chromium and molybdenum. Continuous brittle phases could be successfully avoided with this modification. Furthermore it could be shown that the choice of additives, the heating respectively cooling rate and the brazing temperature have important influence on the microstructure evolution and therefore on the mechanical and corrosive properties of joints. (Abstract Copyright [2008], ...

Energy Technology Data Exchange (ETDEWEB)

In comparison to deterministic criteria, probabilistic reliability indices like interruption frequency and unavailability give a more differentiated insight into reliability in an electrical energy network. One possibility for network planning based on these indices is the definition of limits for customer nodes, another is the monetarisation of reliability in terms of interruption costs. Because of numerous disadvantages, interruption cost methods could not up to now win broad recognition in network planning in Western Europe. A more recent method for the monetarisation of reliability circumventing most of these disadvantages is the insurance system. In this system the customer selects a tariff class in an insurance system, and the utility reimburses its customers in the case of an interruption. In its first section, the paper describes a method for the flexible and realistic optimisation of MV networks. This method based on Genetic optimisation is able to integrate probabilistic ...

Energy Technology Data Exchange (ETDEWEB)

Surface structure analysis, i.e. metallographic analysis of component surfaces with the aid of replicas, is an established method of component monitoring and the only reliable non-destructive method for detecting and analyzing beginning creep damage in the form of creep pores. Creep pore development provides a basis for component condition analysis. It must be noted, however, that the modern martensitic 9-12 % Cr steels - like the established steels 10CrMo9-10 (P22) und X20CrMoV12-1 - have comparatively high creep fracture deformation rates in fatigue tests. This raises the question if these steels can be judged on the basis of data for established steels. The results so far suggest that even with low pore densities (single pores), a higher degree of damage and a shorter time until failure must be assumed. [German] Eine bewaehrte Methode der Bauteilueberwachung stellt die Oberflaechengefuegeuntersuchung, d. h. die metallografische Untersuchung der Bauteiloberflaeche mit Hilfe von ...

Energy Technology Data Exchange (ETDEWEB)

On account of a raised appearing of plastic waste and shreddered light fraction (SLF) from old car utilization as well as legal handicaps experiments were carried out at the Institute of Ferrous Metallurgy (RWTH Aachen) on a laboratory rig to inject DSD (Duales System Deutschland)-plastic waste and SLF with the destination of a subsequent raw material utilization in the blast furnace and cupola furnace. The experiments on the laboratory rig with DSD plastics could verify that by injection of specific coal/plastic mixtures into the blast furnace the injection rate could be raised by an improvement in the conversion degree and therefore the amount of the inserted reducing agent can be lowered. The injection of SLF without reduction of the inert materials and of the contents on alloying elements and/or tramp elements by extensive preparation has no advantages according to the experiments for the blast furnace process. Pilot experiments on the cupola furnace showed that, assuming a certain ...

Energy Technology Data Exchange (ETDEWEB)

The aim of the presented investigation was to gain information about the behaviour of the initiation and growth of intercrystalline creep cracks during creep deformation from the evaluation of metallographic micrographs. The austenitic steel X10 NiCrAlTi 32 20 HT (Alloy 800 HT) was investigated by carrying out creep tests at 800 and 900 C with different nominal stresses until fracture. Additional tests are carried out on certain creep strains in the late tertiary creep stage. The creep tests are followed by a metallographic investigation of the crept specimens. The statistical distribution of the microcrack lengths was used to estimate the rate of crack initiation and crack growth. It is found that the rate of growth of the intercrystalline creep cracks in Alloy 800 HT is dependent on the applied stress and the creep strain reached. The rate of growth of long cracks was only slightly higher than that of short cracks and was lower than predictions based on fracture mechanics concepts. ...

Energy Technology Data Exchange (ETDEWEB)

The paper presents fundamental studies on natural biosorption to algae of heavy metals. The investigations were carried out by TU Berlin University in a special research project (Sfb 193, 'Biologische Behandlung industrieller und gewerblicher Abwaesser'). The chlorophyceae C. vulgaris was used as reference alga, and 38 further algae were analzyed with regard to their sorption characteristics for lead, cadmium, nickel and zinc. The most effective algae were the chlorophyceae C. salina, the cyanophyceae S. hofmani and L. taylorii. The biosorption characteristics of C. salina and L. taylorii were investigated in detail. L. taylorii was found to be exploitable successfully in a technical process, so the investigations were extended to include copper. Knowledge about the chemical processes of biosorption is important for any attempt to modify the biosorption characteristics. Experiments on the incorporation of additional functional groups in the cell wall polysaccharides ...

Energy Technology Data Exchange (ETDEWEB)

The comprehensive survey explains the indications and the specific value of the modern tomographic modalities with respect to the various diagnostic issues. Numerous reproductions of CT, MRI, US scans illustrate the aspects discussed. (orig./CB) [German] Bildgebende Verfahren kommen bei der Abklaerung von Erkrankungen des weiblichen Urogenitaltrakts ergaenzend zu der klinischen Untersuchung zur Anwendung. Kongenitale Uterusanomalien werden primaer mit der HSG oder der Laparoskopie diagnostiziert. Zusaetzlich koennen der transvaginale US und in unklaren Faellen die MRT eingesetzt werden. Die Diagnose entzuendlicher Erkrankungen des weiblichen Genitaltrakts erfolgt in der Regel klinisch. Schnittbildverfahren werden bei therapieresistenten, komplizierten Faellen angewendet. Initial werden benigne Neoplasien des Uterus mit dem transvaginalen US abgeklaert. Eine Verdickung des Endometriums ist dabei ein unspezifischer Befund und kann auf eine Hyperplasie, Polypen oder ein Karzinom ...

Science.gov (United States)

The effect of 50 Hz and 60 Hz (frequencies of current distribution) and 20 kHz to 50 kHz (frequencies of induction cooktop) magnetic interference on implanted pacemakers have been assessed with the present generation of device technology. Sixty patients implanted in 1998 and 1999 with dual chamber pacemakers from 9 different manufacturers were monitored with telemetry while passing through, and standing between a system of two coils. They generated a 50 Hz or a 60 Hz magnetic field at 50 microT. Then, patients used a cooktop at different power. The recordings were made with the standard setting of "medically correct" sensing parameters chosen for the patients. Then pacemakers were reprogrammed to the unipolar mode, with the highest atrial (A) and ventricular (V) sensitivity that did not induce muscular inhibition while moving. Between each exposure (50 Hz, 60 Hz or 20 kHz to 50 kHz), the pacemaker programmation was controlled. At the end of the tests, pacemakers ...

Energy Technology Data Exchange (ETDEWEB)

We have investigated the generation and propagation of misfit dislocations in strained In/sub y/Ga/sub 1-//sub y/As/GaAs multiquantum wells grown by molecular-beam epitaxy, with cross-sectional transmission electron microscopy. The samples are of excellent optical quality, with multiquantum wells having well widths of 100 A, being characterized by excitonic linewidths and Stokes shifts of 1.5--2.5 and 1--2 meV, respectively. We have examined the growth of 2-..mu..m-thick multiquantum-well samples grown either directly on GaAs, or with an intermediate composition buffer layer, and for the cases of small (y = 0.07) and large (y = 0.16) misfits. It is seen that for the case of quantum wells with small misfit, grown directly on GaAs, metastable growth can be achieved. This is confirmed by low-temperature absorption measurements and from transmission electron microscopy experiments performed both before and after post-growth thermal annealing. In the case of quantum wells with large misfits ...

Energy Technology Data Exchange (ETDEWEB)

The thesis relates to an investigation done on greenhouse gases in coniferous forest soils. The production of nitrous oxide (N{sub 2}O) and carbon dioxide (CO{sub 2}), and the consumption of methane (CH{sub 4}) in a temperate forest soil were studied by a rapid and sensitive gas chromatographic (GC) method for analysing all three greenhouse gases at or below ambient levels. Gas fluxes were measured in soil incubation and lysimeter experiments. 15 soil samples were taken at random within a 100 m{sup 2} area in a Norway spruce forest stand (Picea abies). The fluxes of N{sub 2}O, CH{sub 4} and CO{sub 2} were measured under standardized laboratory incubation conditions to investigate spatial variability in relation to other factors such as nitrogen (N) mineralization rate, nitrification rate, organic carbon (OC), total N and pH. The effects of temperature, soil moisture content, and ammonium addition were also studied in an incubation experiment. A more detailed study ...

International Nuclear Information System (INIS)

We study the line widths in the [O III]#lambda#5007 and H#alpha# lines for two groups of planetary nebulae in the Milky Way bulge based upon spectroscopy obtained at the Observatorio Astronomico Nacional in the Sierra San Pedro Martir (OAN-SPM) using the Manchester Echelle Spectrograph. The first sample includes objects early in their evolution, having high H#beta# luminosities, but [O III]#lambda#5007/H#beta# < 3. The second sample comprises objects late in their evolution, with He II #lambda#4686/H#beta#>0.5. These planetary nebulae represent evolutionary phases preceding and following those of the objects studied by Richer et al. in 2008. Our sample of planetary nebulae with weak [O III]#lambda#5007 has a line width distribution similar to that of the expansion velocities of the envelopes of asymptotic giant branch stars and shifted to systematically lower values as compared to the less evolved objects studied by Richer et al. The sample with strong He II #lambda#4686 has a ...

Energy Technology Data Exchange (ETDEWEB)

A large negative ion source for JT-60U produces high current ion beam from a wide extraction area of 45 cm x 110 cm. On the other hand, a cross-sectional area of the negative ion based neutral beam (NNB) injection port on JT-60U is narrow, about 50 cm x 60 cm. In order to inject the neutral beam at a high geometric efficiency, i.e. to suppress beam loss in the beamline, it is necessary to steer the beam for both compensation of undesirable beam deflection in extractor and focusing of the beam. For the JT-60U, two methods are provided for the required beam steering. Among them the results of beam steering experiment by aperture displacement and the design study are summarized in the present report. The experiment was carried out with 400 keV negative ion source, which has the three stage accelerator of similar structure as the JT-60U ion source, at Negative Ion Acceleration Test Stand (NIAS). High energy negative ion beams of the same perveance as that of 500 keV ...

International Nuclear Information System (INIS)

The recovery of noble metals from the quaternary Mo-Ru-Rh-Pd alloy in the simulated insoluble residue was studied by means of Pb extraction and the recovery yield was found to be more than 90% for Ru, Rh and Pd. The recovery yield of Mo was very small due to the oxidative vaporization in air. The decontamination factor for Ce as a stand-in of Pu was determined to be around 200 for one stage. These results on the recovery yields of noble metals from the quaternary alloy and the decontamination factor for Ce are in good agreement with those for the ternary Mo-Ru-Pd alloy previously reported by the present authors. The mutual separation of noble metal elements recovered in Pb button was examined by means of re-extraction with molten Zn and the dissolution in boiling 3M or 6M nitric acid solution. The dissolution fractions of Pd and Rh recovered in the Pb button in boiling 3M and 6M nitric acid solution for 12 h were about 90 and 30%, respectively, and that of Ru was ...

Energy Technology Data Exchange (ETDEWEB)

The article provides a 1998 updated picture of Italy's and the world's photovoltaic market in terms of produced modules and total installed capacity, as well as market growth forecasts up to 2010. After a short description of the state-of-the-art of cell and module manufacturing, ana analysis of the cost of producing a photovoltaic kw is reported for different plant types: stand-alone plants with energy storage batteries, plants connected to low low voltage networks or intended for supporting medium voltage networks, hybrid plants with diesel sets. The article is concluded by illustrating ENEL's (Electric Power Production Company) engagement in the field of photovoltaic solar energy as regards theoretical studies, research and testing of new technologies, and installing plants; over nearly twenty years of activity, ENEL has designed and built a few hundreds of photovoltaic plants for a total capacity of about 4.000 kw, and is currently in ...

Energy Technology Data Exchange (ETDEWEB)

This work is a theoretical investigation on the physical properties of semiconductor-based two-dimensional photonic crystals, in particular for what concerns systems embedded in planar dielectric waveguides (GaAs/AlGaAs, GaInAsP/InP heterostructures, and self-standing membranes) or based on macro-porous silicon. The photonic-band structure of photonic crystals and photonic-crystal slabs is numerically computed and the associated light-line problem is discussed, which points to the issue of intrinsic out-of-lane diffraction losses for the photonic bands lying above the light line. The photonic states are then classified by the group theory formalism: each mode is related to an irreducible representation of the corresponding small point group. The optical properties are investigated by means of the scattering matrix method, which numerically implements a variable-angle-reflectance experiment; comparison with experiments is also provided. The analysis of surface ...

Energy Technology Data Exchange (ETDEWEB)

The position paper will provide the basis for further strategies on offshore wind power development in consideration of ecological and conservation aspects. [German] Das Positionspapier des Bundesministeriums fuer Umwelt, Naturschutz und Reaktorsicherheit (BMU) einschliesslich des Umweltbundesamtes (UBA) und des Bundesamtes fuer Naturschutz (BfN) ist Ergebnis der Arbeiten der BMU-Projektgruppe 'Windenergienutzung im Offshore-Bereich im Hinblick auf die BMU-Anliegen'. Es beschreibt den derzeitigen Stand einer Strategie zur umwelt- und naturvertraeglichen Erschliessung der Windenergienutzung auf See (Offshore). Es bildet die Grundlage fuer die Weiterentwicklung dieser Strategie und dabei insbesondere zur Abstimmung mit den Anliegen anderer Bundesressorts und den Kuestenlaendern, sowie zur intensiveren Einbeziehung beteiligter Verbaende und Fachkreise. Vor dem Hintergrund der zur Genehmigung eingereichten Antraege fuer Offshore-Windparks, mangelnder ...

International Nuclear Information System (INIS)

The dominant shrubs were sagebrush and spiny hopsage; the herbs were dominated by cheatgrass and Sandberg bluegrass. Spiny hopsage appeared to be vulnerable to burning and also to damage by off-road vehicular traffic. It appears to have little or no ability to reproduce through seedlings; once the existing plants are killed they are not likely to be replaced, even if seed-producing plants are nearby. The only pure stand of spiny hopsage known to exist on the Hanford Site is on and near study plot 2H. Sagebrush, like spiny hopsage, is killed by burning and by heavy vehicles. Sagebrush is capable of reproducing via seeds, indicating that it is an inherently aggressive species with a capacity to reestablish itself if parent plants are in the vicinity to act as seed sources. Alien, annual plants, especially cheatgrass, were a major contributor to the herbaceous canopy cover in plots 3S, 4S, and 5S. However, native perennial grasses, especially Sandberg bluegrass, were ...

International Nuclear Information System (INIS)

In the developed world, grid-connected photovoltaics (PVs) are the fastest-growing segment of the energy market. From 1999 to 2009, this industry had a 42% compound annual growth-rate. From 2009 to 2013, it is expected to grow to 45%, and in 2013 the achievement of grid parity - when the cost of solar electricity becomes competitive with conventional retail (including taxes and charges) grid-supplied electricity - is expected in many places worldwide. Grid-connected PV is usually perceived as an energy technology for developed countries, whereas isolated, stand-alone PV is considered as more suited for applications in developing nations, where so many individuals still lack access to electricity. This rationale is based on the still high costs of PV when compared with conventional electricity. We make the case for grid-connected PV generation in Brazil, showing that with the declining costs of PV and the rising prices of conventional electricity, urban populations ...

Energy Technology Data Exchange (ETDEWEB)

We present a collisional-radiative approach of the theoretical analysis of laser-induced breakdown spectroscopy (LIBS) plasmas. This model, which relies on an optimized effective potential atomic structure code, was used to simulate a pure aluminum plasma. The description of aluminum involved a set of 220 atomic levels representative of three different stages of ionization (Al{sup 0}, Al{sup +} and Al{sup ++}). The calculations were carried for stationary plasmas, with input parameters (n{sub e} and T{sub e}) ranging respectively between 10{sup 13-18} cm{sup -3} and 0.3-2 eV. A comparison of our atomic data with some existing databases is made. The code was mainly developed to address the validity of the local thermodynamic equilibrium (LTE) assumption. For usual LIBS plasma parameters, we did not reveal a sizeable discrepancy of the radiative equilibrium of the plasma towards LTE. For cases where LTE was firmly believed to stand, the Boltzmann plot outputs of this ...

Energy Technology Data Exchange (ETDEWEB)

In 1991/1992, VEAG decided to convert its 500 MW plants at Jaenschwalde and Boxberg to the latest state of technology. This even included the discharge of the cleaned flue gas through the existing cooling towers. The site of the flue gas desulphurization plant and also the existing cooling tower shells required routeing of the clean gas lines similar to the routes in the existing plants of RWE. The positive experience accrued with the pipework material `glass-fibre reinforced vinyl ester resin` has also led to the selection of this material here. The universally positive experience gained from existing clean gas lines via cooling towers by very different power station operators induced VEAG and its partners also to equip new construction operations in the new Federal states with this technology. (orig.) [Deutsch] In den Jahren 1991/1992 entschloss sich die VEAG, ihre 500-MW-Anlagen Jaenschwalde und Boxberg auf den neuesten Stand der Technik umzuruesten. Hierzu ...

Energy Technology Data Exchange (ETDEWEB)

The evaluation of possible manufacture-based defects in turbine shafts and housings for component serviceability relevance is of particular interest not only in post-manufacturing NDT but also in evaluation of NDT results obtained by in-service inspections of components with long service lives. The results discussed in the paper are summarized as follows: Most of the examined natural defects in the forgings and castings behave like cracks under the simulated operating conditions and hence may well be evaluated by fracture mechanical methods for their serviceability relevance determined by crack propagation under fatigue, creep and creep-fatigue stress. The empirical correlation of true defect size and US testing results (echo signal, echodynamics, attenuation) permits improved determination of true defect sizes in the turbine components. Care has to be taken to select the proper testing and evaluation methods in compliance with defect types. (orig./MM) [Deutsch] Die ...

International Nuclear Information System (INIS)

The main goals of nuclear astrophysics have been to probe the interiors of stars, stellar explosions, the early moments of cosmic expansion, and the formation and evolution of galaxies and cosmic structure by measurement and application of the relevant nuclear physics. The approach to these goals have generally been from three directions: 1) Careful measurements of the relevant nuclear reactions; 2) Detailed computer models of the relevant astrophysical environments; and 3) Observations of the relevant terrestrial and extra-terrestrial atomic and isotopic abundances. These approaches provide not only insight into the formation and evolution of the elements, but are also pillars upon which a variety of cosmological models as well as models for physics beyond the standard model of particle physics can stand or fall. At present there is a very exciting frontier on all three of these approaches. The development and applications of radioactive-ion-beam and ...

Energy Technology Data Exchange (ETDEWEB)

The needs of large industrial, commercial, and institutional energy consumers are more closely connected with the needs of power utilities and energy services companies, a result of the evolving global energy environment. Consumer choice, competition amongst energy suppliers, and increased demand are brought about in some regions by deregulation. Increasingly, large energy consumers expect high levels of quality and reliability from the energy delivered. As a result, management of the cost and the quality of the energy product and the energy assets that produce, deliver, control and consume it requires different strategies. Three major challenges must be overcome: (1) requirement to support economic and efficient delivery, purchasing and use of energy, (2) requirement to guarantee higher levels of power quality and reliability, and (3) requirement to supply the growing demand for energy while establishing a market-based pricing system. The solution is the enterprise energy management ...

Science.gov (United States)

This project proposes to design and develop a new class of power converters (direct DC to AC) to drastically improve performance and optimize the cost, size, weight and volume of the DC to AC converter in SOFC systems. The proposed topologies employ a high frequency link; direct DC to AC conversion approach. The direct DC to AC conversion approach is more efficient and operates without an intermediate dc-link stage. The absence of the dc-link, results in the elimination of bulky, aluminum electrolytic capacitors, which in turn leads to a reduction in the cost, volume, size and weight of the power electronic converter. The feasibility of two direct DC to AC converter topologies and their suitability to meet SECA objectives will be investigated. Laboratory proto-type converters (3-5kW) will be designed and tested in Phase-1. A detailed design trade-off study along with the test results will be available in the form of a report for the evaluation of SECA Industrial partners. This project ...

Energy Technology Data Exchange (ETDEWEB)

The precipitation of heavy metals as hydroxides is the standard technique for the decontamination of waste water streams polluted by these elements. On the other side, progress in research has been made concerning the biosorption onto dead biomass and bioprecipitation supported by physiologically active bacteria. As the aim of this study, a flexible strategy has been envisaged cleaning a waste water with definite heavy metal load underlying the process mentioned above. Suitable bacteria were enriched and the process was tested in a technical plant. As result, a very high efficiency of heavy metal elimination has been found. The field of application covered by the acquired process is identical with the whole range of the waste water streams polluted by heavy metals. In addition, a second stage may be necessary if there are any further contaminants to be removed. (orig.) [Deutsch] Bei der Reinigung von schwermetallhaltigen Abwaessern ist der derzeitige Stand der ...

Energy Technology Data Exchange (ETDEWEB)

In this article, the technical feasibility of the use of activated carbon, synthetic resins, and various low-cost natural adsorbents for the removal of phenol and its derivatives from contaminated water has been reviewed. Instead of using commercial activated carbon and synthetic resins, researchers have worked on inexpensive materials such as coal fly ash, sludge, biomass, zeolites, and other adsorbents, which have high adsorption capacity and are locally available. The comparison of their removal performance with that of activated carbon and synthetic resins is presented in this study. From our survey of about 100 papers, low-cost adsorbents have demonstrated outstanding removal capabilities for phenol and its derivatives compared to activated carbons. Adsorbents that stand out for high adsorption capacities are coal-reject, residual coal treated with H{sub 3}PO{sub 4}, dried activated sludge, red mud, and cetyl-trimethylammonium bromide-modified montmorillonite. ...

Energy Technology Data Exchange (ETDEWEB)

For millions of people general noise and especially traffic noise are the main sources of environmental pollution. The increasingly stricter noise pollution abatement limiting values laid down by the law call for motor vehicle noise pollution abatement measures. Within the framework of today`s cost- and performance-oriented automobile and engine development developing engineers are required to reduce noise levels. The present state of the art is described and future possibilities of combustion engine structure-borne noise calculation and optimization are discussed from the point of view of K + P Computerunterstuetzte Strukturanalysen GmbH. (orig.) [Deutsch] Laerm allgemein und dabei speziell wiederum der Verkehrslaerm steht fuer Millionen von Menschen an allererster Stelle der persoenlichen Belastung durch die Umwelt. Zur Minderung der Laermbelastung werden vom Gesetzgeber immer schaerfere Grenzwerte vorgeschrieben, die dazu zwingen, Massnahmen zur Geraeuschreduktion am Kraftfahrzeug ...

Energy Technology Data Exchange (ETDEWEB)

The study of providing security in computer networks is a rapidly growing area of interest because the network is the medium over which most attacks or intrusions on computer systems are launched. One approach to solving this problem is the intrusion-detection concept, whose basic premise is that not only abandoning the existing and huge infrastructure of possibly-insecure computer and network systems is impossible, but also replacing them by totally-secure systems may not be feasible or cost effective. Previous work on intrusion-detection systems were performed on stand-alone hosts and on a broadcast local area network (LAN) environment. The focus of our present research is to extend our network intrusion-detection concept from the LAN environment to arbitarily wider areas with the network topology being arbitrary as well. The generalized distributed environment is heterogeneous, i.e., the network nodes can be hosts or servers from different vendors, or some of ...

Energy Technology Data Exchange (ETDEWEB)

TRITEX was a pumped loop with Pb-15.8Li, fabricated from steel 1.4922. In contact with the molten eutectic were also molybdenum, vanadium and armco-iron. The loop was originally designed to investigate tritium extraction using solid getter metals. Over the years the goal changed to the study of metals, corrosion products and purification of the eutectic mixture. Therefore many modifications were done. The first part of this report describes TRITEX. All parts were enclosed in thermoboxes for a homogeneous temperature. One test section was in an argon glove box and could be opened during operation. Other special equipment`s were: permeation membranes and liquid-metal-covergas-interfaces to study the transport of H{sub 2}, D{sub 2} and {sup 3}H, different purification devices, a quartz observation window to see the liquid metal surface, 4 different kinds of flow measurements, level indicators, freeze valves. The second part describes loop operation. Between 1989 and 1996, the eutectic ...

Energy Technology Data Exchange (ETDEWEB)

The experimental effect investigation programme on Zircaloy-4/air oxidation was pursued and expanded to isothermal specimen exposure and the comparison of the oxidation between the atmospheres Ar/O{sub 2} and air. In close connection with the EC project OPSA, which is meanwhile terminated, the investigation concerned specimen exposure in a thermobalance to flowing atmospheres, namely dry Ar/O{sub 2} of composition 80/20 or synthetic air, respectively. As test parameters the linear heat-up rate was varied in the range 5 to 40 K/min and the ramp or holding temperature between 800 and 1500 C. Mass increase and reaction rate were continuously recorded or evaluated in temperature/time dependence. The oxide scale growth was found to be accompanied by colour changes, crack formation and spalling of layers, as well as by dimensional substrate growth, which are the reasons for the observed kinetic results. The microstructural investigation confirms nitrogen to be essentially responsible for the ...

Energy Technology Data Exchange (ETDEWEB)

Purpose: To evaluate a T{sub 2}-weighted URSE sequence for the assessment of pulmonary infiltrations in comparison to CT. Methods: 28 MRT scans of 22 patients with confirmed pneumonia were recorded on a 1.5 Tesla apparatus with an expiratory and diastolic triggered, T{sub 2}-weighted ultrafast-spin-echo sequence in axial slice mode with the following parameters: TR{sub eff}/T{sub E}/Turbofactor 2000-4000/90 ms/21-23; slice thickness/separation 6/0.6 mm; FOV 360 mm; 24 slices. 24 spiral CTs (sice thickness/table advance: 1-2 mm/10 mm) were available for comparison. The separate evaluation of MRTs and CTs was performed by three radiologists in a consensus procedure with regard to pulmonary lesions (e.g., infiltration, round foci, net patterns) and image quality of the MRTs (4-step scale). Results: In 71% of the cases the CTs and MRTs agreed with the diagnosis and representation of the lesions, in 25% MRT was superior. MRT was better for the detection of pulmonary abscesses. In 93% the ...

Energy Technology Data Exchange (ETDEWEB)

Austenitic stainless steel (18% Cr, 12% Ni, Mo gradation between 0,06 to 3,6%) had been solution nitrided. By step-by-step removing, the samples could be prepared with various surface contents of nitrogen from 0.04 to 0.42%. In two test series the influence of nitrogen had been determined. The susceptibility against pitting corrosion of these samples had been tested by the chronopotentiostatical method. For the investigated steel composition and the used corrosion system there is no influence of molybdenum on the effectiveness of nitrogen. The effectiveness of nitrogen can be described by the factor 25 in the PRE. By the investigation of the surfaces with the XPS analysis, it could be shown that the passivation and the pit nucleation is influenced by nitrogen. In these ranges NO{sub x}, NH{sub x}, and NH{sub z}-spectra have been detected. Bound Mo was found in steels containing molybdenum. It is assumed that the repassivation mechanisms of N and Mo work independently of each other. ...

Energy Technology Data Exchange (ETDEWEB)

To evaluate the usefulness of radiation therapy alternative to surgery for clinical N0-N1 non-small cell lung cancer (NSCLC). From 1976 through 1989, 116 patients with NSCLC without mediastinal involvement were treated with definitive radiation therapy alone at Gunma University Hospital. All patients were treated with once-daily standard fractionation using 10 MV X-rays. The total dose ranged from 60 Gy to 80 Gy. The actuarial 2- and 5-year survival rates of the entire group were 43% and 20%, respectively with a median survival time of 19 months. The survival of 76 patients with stage T2 tumors was significantly better than that of 28 patients with T3 tumors (mean survival time 21 versus 15.5 months; p<0.05). Sixty-two patients with tumors less than 5 cm in diameter had a 2-year progression rate of 20%, in comparison with 39% of 54 patients with tumors greater than 5 cm. The difference of survivals for these 2 groups was statistically significant. Twelve patients given a total dose ...

Energy Technology Data Exchange (ETDEWEB)

Nuclear energy will have to cope more and more with a rapid changing environment due to economic competitive pressure and the deregulatory progress. In current economic environment, utilities will have to focus strongly on the reduction of their total generation costs, covering the fuel cycle costs, which are only partly under their control. Developments in the fuel cycle will be in the short-term rather evolutionary addressing the current needs of utilities. However, within the context of sustainable development and more and more inclusion of externalities in energy generation costs, more performing developments in the fuel cycle could become important and feasible. A life-cycle design approach of the fuel cycle will be requested in order to cover all factors in order to decrease significantly the nuclear energy generation cost to complete with other alternative fuels in the long-term. This paper will report on some of the trends one could distinguish in the fuel cycle with emphasis ...

Energy Technology Data Exchange (ETDEWEB)

Atomization of liquid fuel in aircraft engines requires application of airblast atomizers, where the kerosene is supplied into the shear layer between two swirling airstreams. The transfer of this functional principle towards gaseous fuel, as illustrated in Fig. 1, yielded a strong influence of the swirl arrangement of the airflows on flame stability and homogeneity of the fuel/air-mixture. Compared to the co-swirl configuration the flow field of the counter-swirl arrangement exhibits a marked increase of the mass flow recirculated in the internal recirculation zone and a reduction of its length in axial direction. This is attributed to the faster decay of tangential velocity maxima in case of counter-rotating airflows. This generates a stronger positive axial pressure gradient dp/dx, thus enhancing the internal recirculation zone. Analysis of local turbulence quantities yields a restriction of turbulent exchange to smaller radial sections and lower maximum values in the jet dominated ...

Energy Technology Data Exchange (ETDEWEB)

Which imaging modalities are appropriate for the Differential diagnosis of Rheumatic diseases. MRI has far most the highest sensitivity and is unequaled in its brilliant presentation of Anatomy and Pathology. But it is sometimes forgotten, that this is at least in part the result of carefully selected sequences, dedicated to the expected result. In a method totally independent of any result, this should not be the case. In contrary this method should be highly standardised and regardless what will be the findings. This is true for Plain X-ray. It will be shown, that already the outer silhouette of the soft parts with different features of swelling, and differences in density and even more - defects or appositions of the bony silhouette in the majority of cases at least will allow to classify the patient for a group of diseases and in many cases will lead to a definite diagnosis. Differential diagnoses like Rheumatoid Arthritis versus Psoriatic Arthritis or simply but not always simple ...

Energy Technology Data Exchange (ETDEWEB)

This report describes work carried out in the context of TurboTech Interim for the development of a system for monitoring stationary gas turbines for approaching the stability limit of the compressor. The requirements for the system components were defined and the suitability of different types and positions of pressure sensors were examined and evaluated. It was found very early in the work that, due to the complexity of the object being monitored, one would not succeed in finding a simple criterion for monitoring the pump limit. Rather, apart from the selection of suitable sensors and optimum positions, one must analyse the present signals in different ways and create a decision matrix from this. Existing work on this subject is mostly concerned with the phenomena in the context of experiments on experimental compressors or is not suitable for the requirements of stationary industrial gas turbines. The project is being carried out in the context of TurboTech II with the main aims of: ...

Energy Technology Data Exchange (ETDEWEB)

An efficient method of hydrogen storage in nano-porous carbons is its reversible sorption by electrochemical decomposition of a KOH water solution according to the following equation: C + xH{sub 2}O + xe{sup -} {yields} (CH{sub x}) + xOH{sup -} where (CH{sub x}) stands for the hydrogen inserted into the nano-porous carbon during charging and oxidized during discharging. Although various carbon materials have been investigated as hydrogen adsorbents, the information about the storage mechanism as well as the nature of the hydrogen/carbon interaction is still not sufficient. In order to extend the understanding of the process, carbon samples charged electrochemically were investigated by temperature programmed desorption (TPD). The nature of the hydrogen/carbon interaction was studied by electrochemical analysis at different temperatures. The TPD experiments consist of heating the samples from room temperature to 950 C and of quantitative analysis by On-line mass ...

Energy Technology Data Exchange (ETDEWEB)

Purpose: In an experimental study, the correlation between the trabecular bone density of the different regions of the proximal femur and the fracture load in the setting of femoral neck fractures was examined. Methods: The bone mineral density 41 random proximal human femora was estimated by single-energy quanitative CT (SE-QCT). The trabecular bone density was measured at the greatest possible extracortical volume at midcapital, midneck and intertrochanteric level and in the 1 cm{sup 3} volumes of the centres of these regions in a standardised 10 mm thick slice in the middle of the femoral neck axis (in mg/ml Ca-hydroxyl apatite). The proximal femora were then isolated and mounted on a compression/bending device under two-legged stand conditions and loaded up to the point when a femoral neck fracture occurred. Results: Statistical analysis revealed a linear correlation between the trabecular bone density and the fracture load for the greater regions, with the ...

Science.gov (United States)

Feasibility of depositing continuous films of nano-porous alumino-silicates, primarily zeolites and MCM-41, on metallic and non-metallic substrates was examined with an aim to develop membranes for separation of gaseous mixtures and also for application as hydrogen storage material. Mesoporous silica was deposited in-side the pores of these nano-porous disks with an aim to develop membranes for selective separations. Our study involves supported zeolite film growth on substrates using in-situ hydrothermal synthesis. Faujasite, Silicalite and Mesoporous silica have been grown on various metallic and non-metallic supports. Metallic substrates used for film growth included anodized titanium, sodium hydroxide treated Titanium, Anodized aluminum, and sintered copper. A non-metallic substrate used was nano-porous aluminum oxide. Zeolite film growth was characterized using Scanning Electron Microscope (AMRAY 1820) and High Resolution Transmission electron microscope. Silicalite was found to ...

Energy Technology Data Exchange (ETDEWEB)

Developing safe, reliable, cost-effective, and efficient hydrogen-electricity co-generation systems is an important step in the quest for national energy security and minimized reliance on foreign oil. This project aimed to, through materials research, develop a cost-effective advanced technology cogenerating hydrogen and electricity directly from distributed natural gas and/or coal-derived fuels. This advanced technology was built upon a novel hybrid module composed of solid-oxide fuel-assisted electrolysis cells (SOFECs) and solid-oxide fuel cells (SOFCs), both of which were in planar, anode-supported designs. A SOFEC is an electrochemical device, in which an oxidizable fuel and steam are fed to the anode and cathode, respectively. Steam on the cathode is split into oxygen ions that are transported through an oxygen ion-conducting electrolyte (i.e. YSZ) to oxidize the anode fuel. The dissociated hydrogen and residual steam are exhausted from the SOFEC cathode and then separated by ...

Energy Technology Data Exchange (ETDEWEB)

CRE is the French commission for energy regulation. CRE's remit is to assist in ensuring the proper operation of the electricity and natural gas markets for the benefit of the end-user. In particular, CRE ensures that the conditions of access to electricity and natural gas transmission and distribution systems do not hinder the development of competition. It monitors, for the electricity and natural gas sectors, all transactions made between suppliers, traders and producers, all transactions made on the organised markets and cross-border trading. It ensures that suppliers, traders and producers propose offers that are consistent with their financial and technical constraints. It monitors the implementation of and compliance with regulations giving consumers the right to choose their supplier in a competitive market, and allowing new suppliers to enter the market. This document is the 2008 activity report of CRE. Content: A - How CRE works: CRE regulatory authority and ...

Energy Technology Data Exchange (ETDEWEB)

This report completes the documentation for the research project 'High Pressure Compressor - Preliminary Design as Basis for the Development of an Efficient and Environmentally Friendly Core Engine' which was funded by the Ministry of Economics of State Brandenburg. The objective of the project is to deliver a preliminary compressor aerodynamic design as well as design studies for an efficient, weight and cost improved compressor. The increase of stage pressure ratio and improved efficiency, whilst stage and blade count is reduced, has been achieved by advanced 3D methods. Compressor stability also at off-design conditions will be retained. The mechanical design focusses on a cost and weight optimised rotor not only for a conventional bladed discs but also for Blish stages. Various options for split casings have been developed and assessed. Alternative vortex reducers based on different design options have been carried out. The results from this project will be ...

Energy Technology Data Exchange (ETDEWEB)

The Stockpile Stewardship Program (SSP) is a single, highly integrated technical program for maintaining the safety and reliability of the U.S. nuclear stockpile. The SSP uses past nuclear test data along with current and future nonnuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of current facilities and programs along with new experimental facilities and computational enhancements to support these programs. The Advanced Simulation and Computing Program (ASC)1 is a cornerstone of the SSP, providing simulation capabilities and computational resources to support the annual stockpile assessment and certification, to study advanced nuclear-weapons design and ...

Energy Technology Data Exchange (ETDEWEB)

Magnetic resonance imaging (MRI) as a diagnostic imaging tool relies on the generation of magnetic fields, whereas the computerized tomography (CT) uses X-radiation. The fundamental principle of MRI is the magnetic resonance of paramagnetic atomic nuclei. These nuclei, as e.g. protons (= hydrogen nuclei), are aligned in required orientation by application of a strong magnetic field. Upon simultaneous application of an electromagnetic high-frequency field perpendicular to the axis of the basic magnetic field, and in response to periodical changing of the electromagnetic field at a given frequency, the originally aligned paramagnetic nuclei are forced into a movement similar to that of a ``whipping top``. When the resonance frequency is shut off, the nuclei return to their former, aligned positions, inducing a weak signal in a coil. The series of signals generated by multiple repetition of this process of excitation of nuclei and their return to aligned rest is used as input to a ...

Energy Technology Data Exchange (ETDEWEB)

Purpose: To assess the new method of 3-dimensional echocardiography in comparison to the 'gold standard' MRI as to its ability to calculate left ventricular volumes in patients with congenital heart disease. Materials and methods: Eighteen patients between the ages of 3.9 to 37.3 years (mean: 12.8{+-}9.7) with a geometrically abnormal left ventricle were examined using a 1.5 T scanner with a fast gradient-echo sequence (TR=14 ms, TE=2.6-2.9 ms, FOV=300-400 mm, flip angle=20 , matrix=128:256, slice thickness=5 mm, retrospective gating) in multislice-multiphase technique. Transthoracic 3D-echocardiography was performed with a 3.5 MHz transducer and a Tomtec {sup trademark} (Munich, Germany) system for 3D reconstruction. Results: Volume calculation was possible in all patients with 3D-echocardiography, but the muscle mass calculation only succeeded in 11 to 18 patients (61%) due to inadequate visualization of the entire myocardium. Comparing MRI and 3D-echocardiography, ...

Energy Technology Data Exchange (ETDEWEB)

An efficient method of hydrogen storage in nano-porous carbons is its reversible sorption by electrochemical decomposition of a KOH water solution [1-3] according to the following equation: C + xH{sub 2}O + xe{sup -} {yields} (CH{sub x}) + xOH{sup -} where (CH{sub x}) stands for the hydrogen inserted into the nano-porous carbon during charging and oxidized during discharging. Although various carbon materials have been investigated as hydrogen adsorbents, the information about the storage mechanism as well as the nature of the hydrogen/carbon interaction is still not sufficient. In order to extend the understanding of the process, carbon samples charged electrochemically were investigated by temperature programmed desorpt(TPD). The nature of the hydrogen/carbon interaction was studied by electrochemical analysis at different temperatures. The TPD experiments consist of heating the samples from room temperature to 950 C and of quantitative analysis by on-line mass ...

Energy Technology Data Exchange (ETDEWEB)

Within its competence for energy research, the Bundesministerium fuer Wirtschaft und Arbeit (BMWA) (Federal Ministry of Economics and Technology) sponsors investigations into the safety of nuclear power plants. The objective of these investigations is to provide fundamental knowledge, procedures and methods to contribute to realistic safety assessments of nuclear installations, to the further development of safety technology and to make use of the potential of innovative safety-related approaches. The Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, by order to the BMWi, continuously issues information on the status of such investigations by publishing semi-annual and annual progress reports within the series of GRS-F-Fortschrittsberichte (GRS-F-Progress Reports). Each progress report represents a compilation of individual reports about the objectives, work performed, results achieved, next steps of the work etc. The individual reports are prepared in a standard form by the ...

Energy Technology Data Exchange (ETDEWEB)

Under the repository storage conditions of Eram and Konrad, waste packages designed for permanent storage must not contain or release freely mobile liquids, except for the minimum residues attainable by reasonable efforts or unavoidable. In accordance with a directive issued by the German Federal Ministry for the Environment (BMU), waste conditioning must be carried out so as to minimize waste volumes and, if possible, on the site where the waste arises. Liquid waste is conditioned most effectively by drying. At the present time, various different processes for drying liquid waste are employed as reflected by the state of the art: The Robe process; roller drying; the RDA process; Favorit; in-drum drying; and HPA liquid waste drying with make-up feed. The HPA process offers these advantages: Drying under atmospheric conditions, which means high level of dryness (freely mobile and releasable water is removed); the residual water content is 10%; isothermal drying by hot air, which ...

Energy Technology Data Exchange (ETDEWEB)

The compositions of the Earth's crust and mantle, and those of the Moon and Mars, are relatively well known both isotopically and elementally. The same is true of our knowledge of the asteroid belt composition, based on meteorite analyses. Remote measurements of Venus, the Jovian atmosphere, and the outer planet moons, have provided some estimates of their compositions. The Sun constitutes a large majority, > 99%, of all the matter in the solar system. The elemental composition of the photosphere, the visible 'surface' of the Sun, is constrained by absorption lines produced by particles above the surface. Abundances for many elements are reported to the {+-}10 or 20% accuracy level. However, the abundances of other important elements, such as neon, cannot be determined in this way due to a relative lack of atomic states at low excitation energies. Additionally and most importantly, the isotopic composition of the Sun cannot be determined astronomically ...

International Nuclear Information System (INIS)

In various situations, measurements in prompt gamma neutron activation analysis (PGNAA) are performed to determine the amount of an elemental impurity relative to that of a major constituent of the matrix. An example of this is the measurement of hydrogen concentration in a metallic matrix. In all such cases, a major contributor to the uncertainty in the measurement is the uncertainty in the ratio of the high-purity germanium (HPGe) detector full-energy peak efficiency for the gamma-ray lines of interest (i.e., impurity and matrix gammas). Usually, the ratio is derived from the relative peak efficiency curve, which is determined using isotopic standards that emit multiple gamma ray lines (e.g., "1"5"2Eu) in the energy range <3000 keV, or using prompt gamma radionuclides (e.g., "1"4N, "3"5Cl) in the energy range >3000 keV. In either case, the uncertainty in the ratio of the peak efficiency values derived from such measurements will be on the order of a few percent at best because ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this work is to investigate whether any morphometric or densitometric are detectable in the kidneys of type 2 diabetic patients. 40 diabetic patients were examined and of 20 non-diabetics (the control group) were submitted to triphasic helical CT for different abdominal conditions. The type 2 diabetic patients were 23 men and 17 women, mean age 62 years, while the nondiabetic controls were 12 men and 8 women, mean age 58 years. All the CT images were analyzed using the Multiplanar Reconstruction (MPR) software. It was evaluated morphometric features, such as the presence of parenchymal or vascular calcifications, axial and coronal renal diameters, coronal renal area, and cortico medullary ratio, and densitometric and functional features, such as unenhanced renal density, cortical and medullary density in the arterial phase, parenchymal density in the nephrographic phase, and contrast elimination. It was also compared the results in the subgroups of patients with those in ...

ScienceCinema

...and and ...and and the ...and ...of and ...and ...and ? ...? right and ...than i am grateful and ...the making forces and a second presentation and ...and ...and ...and ...and ...and ...one and two sons-in-law and as ...as adults world so you get and ? or less they need to be ...and ...starting to speak and always ...and ...and and course houston's ...and i was probably ...and the progress of the ...? and ...and ...? and ...and ...and ...? and ...for one year and half ago we bought ...and ...described one year and half ago and ...and ...and ...uh ? and er i'm ...and ...and ...and ...and ...and ...and ...? and the largest ...and ...more than five and that's used ...and ...and a piece by ...and um ? ...and you ...by and unwise ...? and ...and and they stop if you if you ...and and ...the reaction cross section and the experiments and ...and ...and ...and and ...to adjust and forty nothing's out maybe this piece of them ? and ...it's not true and ...and and ...and ...and ...and ...