Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

The Cu- and Ni-based bulk metallic glass matrix composites were fabricated by spark plasma sintering of a mixture of gas-atomized metallic glass powders and ductile brass powders. The brass powders added for the enhancement of plasticity are well distributed in the matrix after consolidation. The matrix of the composite materials remains as a fully amorphous phase after consolidation process. With increasing the brass content, the level of plasticity strain increased, although the level of strength decreased. The successful consolidation of metallic glass matrix composite with high density was attributed to viscous flow in the supercooled liquid state during spark plasma sintering.

International Nuclear Information System (INIS)

The purpose of this research is to investigate the micro-mechanism of deformation behavior of metallic glasses. We report the results of direct observations of short-range and medium-range structural change during tensile deformation of metallic glasses by high energy X-ray diffraction method. Cu50Zr50 and Ni30Zr70 metallic glass samples in the ribbon shape (1.5 mm width and 25 ?m) were made by using rapid quenching method. Tensile deformation added to the sample was made by using special equipment adopted for measuring the high energy X-ray diffraction. The peaks in pair distribution function g(r) for Cu50Zr50 and N30iZr70 metallic glasses move zigzag into front and into rear during tensile deformation. These results of direct observation on atomic distribution change for Cu50Zr50 and Ni30Zr70 ...

Energy Technology Data Exchange (ETDEWEB)

It is well known that composite armors, consisting of glass elements confined with metallic tampers, are extraordinarily effective against shaped charge attack. Early experiments showed that jets fired against glass targets appeared to be bombarded by tiny fragments that destroyed alignment and reduced residual jet penetration. This result was attributed to an elastic rebound effect in which the outward radial motion of the target around the jet periphery was supposed to be arrested by tensile hoop stresses which developed behind the divergent shock front. Glass fragments were then accelerated radially inward and these destabilized the jet. To sustain the large tensile hoop stresses required, the glass must not have been fractured by the initial shock, behind which the stress state is typically well above the Hugoniot elastic limit. Modeling the penetration of a jet into ...

International Nuclear Information System (INIS)

Radionuclide X-ray fluorescence and particle induced X-ray emission methods were used for a rapid and nondestructive analysis of metallic glasses. The methods are compared in accuracy and precision with the atomic absorption method. Some results of analyses of Fe_xNi_8_0_-_xB_2_0 materials are briefly reviewed. The distribution of elements along the width and length, and a qualitative analysis of the composition of material surfaces are considered. (author) 3 refs.

Environmental Research Database

ObjectivesObjectives Not AvailableDescriptionWe will study the electrodeposition of metals from solutions containing a~%~ mixture of metal cations, in order to discover the conditions which lead to the separation of the metals. Measurements will be made both using small glass cells and using a more realistic size (10 cm x 10 cm electrodes) of electrodeposition cell.~%~

Energy Technology Data Exchange (ETDEWEB)

Thermal, electrical, and electrochemical properties were investigated for the (100-x)(0.6Li{sub 2}S{center{underscore}dot}0.4SiS{sub 2}){center{underscore}dot}xLi{sub 4}SiO{sub 4} oxysulfide glasses. The glass with x = 5 exhibited high electrical conductivity of about 10{sup {minus}3} S cm{sup {minus}1} at room temperature, high glass stability against crystallization, and good chemical stability in contact with Li metal. Cyclic voltammetry also suggested that this glass has a wide electrochemical window of more than 10 V. On the other hand, further addition of Li{sub 4}SiO{sub 4} up to 20 mol% lowered the conductivity, glass stability against crystallization, and electrochemical stability for the oxysulfide glasses.

British Library Electronic Table of Contents (United Kingdom)

Statement of problem Although the esthetic outcome of a collarless metal ceramic restoration is superior to that of a restoration with a metal margin, its mechanical strength has not been evaluated. Purpose The purpose of this study was to evaluate and compare the fracture resistance of metal ceramic restorations with metal margins to that of metal ceramic restorations with circumferential porcelain margins, after exposure to masticatory simulation. Material and methods Twenty-four metal ceramic restorations were fabricated and paired with 24 cobalt-chrome tooth analogs. Twelve of the specimens had metal margins, while the remainder had circumferential porcelain margins. The restorations were cemented on the metal tooth analogs with a resin-modified glass ionomer luting agent (FujiCEM). Al...

Energy Technology Data Exchange (ETDEWEB)

This paper attempts to explain the peculiarities of the radial-distribution function of metal glasses without involving ideas of the amorphous structure. On a computer, the radial atomic density for a spherical eutectic single crystal of the composition Fe/sub 84/C/sub 16/ of radius 15 A formed by alternating small crystals of e-Fe and Fe/sub 3/C of cubic form with the edge of the cube ca 10 A. For the sake of clarity, the diagram of such a quasisingle crystal is shown and has been given a cubic boundary. The change in the relationship between the heights of the subpeaks of the second maximum of the radial distribution function of atoms in the Fe-B glasses with a change in the concentration of boron can be explained by the change in the space group of the Fe/sub 3/B metastable boride which is formed in this system.

British Library Electronic Table of Contents (United Kingdom)

Introduction The objective of this study was to investigate the in-vitro fluoride release from a glass ionomer orthodontic bonding system (Fuji I, GC Corporation, Tokyo, Japan) over a 2-month period and the in-vivo enamel fluoride uptake after 6 months. Methods Ten metal brackets were bonded with either glass ionomer or composite resin (Transbond XT, 3M Unitek, Monrovia, Calif; Light Cure), which served as controls, to recently extracted molars. The bonded teeth, cut at the level of their roots, were stored in distilled water that was renewed after every fluoride measurement at 1, 3, 7, 30, and 60 days. The in-vitro fluoride release was measured by using a fluoride ion-selective electrode, connected to an ion analyzer. Fifteen pairs of premolars were bonded with metal brackets with either ...

British Library Electronic Table of Contents (United Kingdom)

Metallic Zn films were deposited on glass substrates by electron-beam evaporation. ZnO films were synthesized by thermal oxidation of Zn metallic films in air. At the annealing temperature of 550 ?C, ZnO nanowires appeared on the surface, which mainly result from the decrease of oxidation rate. A ZnO ultraviolet photodetector was fabricated based on a metal-semiconductor-metal planar structure. The detector showed a large UV photoresponse with an increase of two orders of magnitude. It is concluded that promising UV detectors can be obtained on ZnO films by thermal oxidation of Zn metallic films. The ways of performing spectral response measurements for polycrystalline ZnO films are also discussed.

International Nuclear Information System (INIS)

It is generally known that a number of metallic glasses have excellent corrosion resistance in a variety of chemically hostile environments. Consequently, the use of laser cladding to coat a massive crystalline material such as aluminium with a layer of a metallic glass has obvious advantages. In this paper, the authors will show that the formation of a predominantly amorphous layer of Zr_6_0Al_1_5NI_2_5 alloy by laser processing is possible, if the obstacles to amorphization are overcome. In addition, evidence of the excellent corrosion resistance of this alloy in a NaCl solution will be given. A comparative study of the corrosion behavior of this amorphous alloy with pure aluminium and Al-Cr alloy will be done, in order to complete previous studies of laser processed coatings of aluminum substrates.

Energy Technology Data Exchange (ETDEWEB)

At least quinary alloys form metallic glass upon cooling below the glass transition temperature at a rate less than 10.sup.3 K/s. Such alloys comprise zirconium and/or hafnium in the range of 45 to 65 atomic percent, titanium and/or niobium in the range of 4 to 7.5 atomic percent, and aluminum and/or zinc in the range of 5 to 15 atomic percent. The balance of the alloy compositions comprise copper, iron, and cobalt and/or nickel. The composition is constrained such that the atomic percentage of iron is less than 10 percent. Further, the ratio of copper to nickel and/or cobalt is in the range of from 1:2 to 2:1. The alloy composition formula is: (Zr,Hf).sub.a (Al,Zn).sub.b (Ti,Nb).sub.c (Cu.sub.x Fe.sub.y (Ni,Co).sub.z).sub.d wherein the constraints upon the formula are: a ranges from 45 to 65 atomic percent, b ranges from 5 to 15 atomic percent, c ranges from 4 to 7.5 atomic percent, d comprises the balance, d.multidot.y is ...

Wastenet

... Zahra-Kingrsquo;s practice utilizes a range of media including textiles, metal casting, glass, sound, film and photography. Qualifications English Major from BA (Social Science) 1991; BA(Visual Arts) 1991; Grad. Dip. (Fine Art - Printmaking) 1993; Candidate for MFA 2001; Ph.D 2005. School of Art Research Clusters Art and Environmental Sustainability Art, ...

International Nuclear Information System (INIS)

It if first shown, that the effective field of uniaxial magnetic anisotropy of Fe-Cr-P-C and Fe-Ni-B-Si system amorphous alloys is reduced with an increase of the source melt isothermal exposure time. The behaviour noted is conditioned by microcoherence and relaxation processes in the nonequilibrium liquid phase after crystal-liquid phase transition.

Energy Technology Data Exchange (ETDEWEB)

After periodic testing of a large-scale spray calciner/ceramic melter vitrification system over a 2-yr period, sufficient corrosion was noted on various parts of the vitrification system to warrant its disassembly and inspection. A majority of the 316 SS sintered metal filters on the spray calciner were damaged by chemical corrosion and/or high temperature oxidation. Inconel-601 portions of the melter lid were attacked by chlorides and sulfates which volatilized from the molten glass. The refractory blocks, making up the walls of the melter, were attacked by the waste glass. This attack was occurring when operating temperatures were >1200/sup 0/C. The melter floor was protected by a sludge layer and showed no corrosion. Corrosion to the Inconel-690 electrodes was minimal, and no corrosion was noted in the offgas treatment system downstream of the sintered metal filters. It is believed that most of ...

Science.gov (United States)

Continuous metallic glass ribbons were produced by mejans of liquid-quenching at rates >10/sup 50/C/s. The ribbons, typically 30 ..mu..m thick and 1 to 2 mm wide, were determined to be glassy by X-ray diffraction (XRD) employing CuK..cap alpha.. and MoK..cap alpha.. radiation. Mechanical properties of the as-quenched product were determined by measurements of hardness, tensile strength and Young's modulus. The Vicker's diamond pyramid microhardness (H/sub V/) was measured on epoxy mounted samples using a Lietz Miniload instrument with a 100 g load. Tensile tests were conducted in an Instron machine using specimens which were hand-polished to produce smooth, parallel sides. Young's modulus (E) is given by the relationship rho V/sub E/sup 2//. V/sub E/, the velocity of extensional mode waves, was measured by the pulse-echo technique using a Panametrics Intervalometer and glass density, rho, was ...

Energy Technology Data Exchange (ETDEWEB)

We analyse several amorphous Pdsub(1-x)Sisub(x) alloys obtained by simulation. The metalloid atoms environments can be studied in the same way as that described in the first paper of this series. The main part of this paper is devoted to the evolution of the density as a function of the concentration. In order to interpret the values obtained by the simulation, we develop two models: the first one assumes a complete disorder: the second one, which is shown to be better, assumes a tendency to a local ordering: Si atoms are assumed to have only Pd neighbours.

International Nuclear Information System (INIS)

The numerical analysis of the experimental data on viscosity change by time in the period after fast heating and crystal-liquid phase transition for the copper nonequilibrium melts and the Fe_7_0Cr_1_0P_1_3C_7 glass-forming melt near their melting temperatures is accomplished through the method of correlation functions and the Rytov-Dimentberg criterion. The observed dependences have nonmonotonic oscillating character but they do not relate to auto-oscillations. The proposed theoretical model of the properties oscillations origination by relaxation in the nonequilibrium liquids explains them as manifestation of noise-induced transitions in the metastable area near the critical temperatures (melting, structural transitions)

British Library Electronic Table of Contents (United Kingdom)

Properties of photoconductive ultraviolet detectors fabricated on ZnO films were presented. Highly c-axis oriented ZnO films were grown on glass substrates by pulsed laser deposition. Ultraviolet photodetectors were fabricated based on metal-semiconductor-metal planar structures. The photoresponsivity and the quantum efficiency are much higher in the ultraviolet range than in the visible range, and the peak values are around 360nm. Photocurrent transients show that the detector has a large photocurrent with the peak value of 2.8mA, and a slow photoresponse with a rise time of 5min and a decay time of 7min. The response curve of the detector is fitted well with exponential curve. The large photocurrent should result from the both effects of the accumulation of conduction electrons and the d...

Energy Technology Data Exchange (ETDEWEB)

Solar cells consisting of polymer layers sandwiched between a transparent electrode on glass and a metal top electrode are studied using dynamic time-of-flight secondary ion mass spectrometry (TOF-SIMS) in dual-beam mode. Because depth profiling of polymers and polymer-metal stacks is a relatively new field the craters were thoroughly investigated by environmental SEM (ESEM), interferometry, surface profilometry and tapping mode AFM. A huge increase in crater bottom roughness was observed when starting from the aluminum top layer going in depth, resulting in a loss of depth resolution. It is shown that layer-to-layer diffusion and contaminants at buried interfaces can be extracted from the depth profiles when taking into account the loss of depth resolution.

Energy Technology Data Exchange (ETDEWEB)

This report is a review of waste form options for the immobilization of high-level-liquid wastes from the nuclear fuel cycle. This review covers the status of international research and development on waste forms as of May 1979. Although the emphasis in this report is on waste form properties, process parameters are discussed where they may affect final waste form properties. A summary table is provided listing properties of various nuclear waste form options. It is concluded that proposed waste forms have properties falling within a relatively narrow range. In regard to crystalline versus glass waste forms, the conclusion is that either glass of crystalline materials can be shown to have some advantage when a single property is considered; however, at this date no single waste form offers optimum properties over the entire range of characteristics investigated. A long-term effort has been applied to the development of ...

Science.gov (United States)

Not Available

Science.gov (United States)

Surface crystallization and surface-to-bulk ratio in high-level waste glasses.

Energy Technology Data Exchange (ETDEWEB)

During past two decades, the importance of rechargeable lithium cells has been emphasized and a large variety of materials has been discovered and evaluated for use as reversible cathodes and electrolytes. Materials that undergo intercalation or topochemical reactions with lithium have been investigated as candidates for cathodes in nonaqueous secondary lithium cells (1). Recent interest in researching cathode active materials has mainly focussed on crystalline transition metal chalcogenides. On the other hand, electrochemical behaviors of several amorphous materials have been reported, for example MoS/sub 2/,MoS/sub 3/,V/sub 2/S/sub 5/ (2) and LiV/sub 3/O/sub 8/ (3). However, no successful cycling behavior has been obtained except for MoS/sub 2/ in the amorphous state. This paper reports electrochemical data on rechargeable vanadate glasses in the system V/sub 2/O/sub 5/-P/sub 2/O/sub 5/.

Energy Technology Data Exchange (ETDEWEB)

The research carried out in Canada in the design of containers for the disposal of radioactive waste has focussed on spent nuclear fuel, even though the quantities of other currently stored radioactive wastes are substantially greater. Research carried out at the Royal Military College of Canada on the effects of mixed fields of radiation on high polymer adhesives and composite materials has shown that some polymers are quite resistant to radiation and could well serve in the fabrication of radioactive waste disposal containers. The purpose of this research was to determine if thermoplastic polymers could be used as superior materials to replace metals in the application of low and intermediate level radioactive waste disposal containers. Polymers have the advantage that they do not corrode like metals. The experimental methods, used in this research, focused on the effects of radiation on the properties of the materials. Polypropylene, Nylon ...

Energy Technology Data Exchange (ETDEWEB)

Ag, Cu, and Ni metallizations were inkjet printed with near vacuum deposition quality. The approach developed can be easily extended to other conductors such as Pt, Pd, Au, etc. Thick highly conducting lines of Ag and Cu demonstrating good adhesion to glass, Si, and printed circuit board (PCB) have been printed at 100-200 deg C in air and N2 respectively. Ag grids were inkjet-printed on Si solar cells and fired through the silicon nitride AR layer at 850 deg C, resulting in 8% cells. Next generation inks, including an ink that etches silicon nitride, have now been developed. Multi-layer inkjet printing of the etching ink followed by Ag ink produced contacts under milder conditions and gave solar cells with efficiencies as high as 12%.

British Library Electronic Table of Contents (United Kingdom)

Samples of Fe78B13Si9 (Metglas 2605 TCA) and Fe77Cr2B16Si5 (Metglas 2605 S3A) were exposed to pulsed excimer laser irradiation at repetition rates of 15, 25 and 50Hz. The occurrence of out-of-plane magnetic anisotropy, changes in the average hyperfine magnetic field and width of the hyperfine field distribution were evidenced by transmission Mossbauer spectroscopy. The variation of the recoilless fraction with laser processing parameters was derived from the simultaneous recording of Mossbauer spectra using a stainless steel etalon as a dual absorber. Conclusions on the onset of long-range magnetic order were formulated.

Energy Technology Data Exchange (ETDEWEB)

Structural silicides have important high temperature applications in oxidizing and aggressive environments. Most prominent are MoSi{sub 2}-based materials, which are borderline ceramic-intermetallic compounds. MoSi{sub 2} single crystals exhibit macroscopic compressive ductility at temperatures below room temperature in some orientations. Polycrystalline MoSi{sub 2} possesses elevated temperature creep behavior which is highly sensitive to grain size. MoSi{sub 2}-Si{sub 3}N{sub 4} composites show an important combination of oxidation resistance, creep resistance, and low temperature fracture toughness. Current potential applications of MoSi{sub 2}-based materials include furnace heating elements, molten metal lances, industrial gas burners, aerospace turbine engine components, diesel engine glow plugs, and materials for glass processing.

Energy Technology Data Exchange (ETDEWEB)

Amorphous metals have an atomic structure resembling that of glass, and have high strength, toughness, and excellent magnetic properties for transformer applications. This type of metal has the potential to reduce the core losses of electromagnetic apparatus by 70-75% compared to the best grain-oriented silicon iron currently used. If all 4 million distribution transformers now in service in Canada were replaced by the more efficient amorphous units, it is estimated that over 5.25 billion kWh of energy could be saved annually. The experience of the General Electric (GE) Company and other researchers with operation of amorphous transformers is described. GE first tried operating amorphous metal transformers on a utility distribution system in April 1982. The shell-type cruciform design showed stable, low-loss performance over eight years of service. GE and the Electric Power Research Institute cooperated ...

Energy Technology Data Exchange (ETDEWEB)

A glass furnace, consisting of a combustion space and a glass melter, uses combustion heat to melt sand and cullet into liquid glass to make products. Glass quality is mainly dependent on the temperature, glass composition, and the level of impurities in a glass melter, which include solid batch/cullet particles, liquid glass, and gas bubbles. A comprehensive computational model using an Eulerian approach has been developed to simulate multiphase flows in a glass melter. It includes all the phases, divides solid particles or gas bubbles into various size groups, and treats each group as a continuum. The derived mass, momentum, and energy conservation equations of the flow are solved for local properties for each phase. The simulation considers the heating and melting of the batch (mainly from the radiative heat from ...

Energy Technology Data Exchange (ETDEWEB)

Objective was to develop a glass utilizing the silica waste material from geothermal energy production, and to supply local artists with this glass to make artistic objects. A glass composed of 93% indigenous Hawaiian materials was developed; 24 artists made 110 objects from this glass. A market was found for art objects made from this material.

Science.gov (United States)

A pyrochemical partitioning process has been conceptually designed so that the transmutation of spent LWR fuels in PEACER can produce mainly low-level waste (Class C waste) for near-surface burial. Chloride salt technology developed for IFR has been employed as the baseline. Electrorefining, reductive extraction and salt recycling steps are used to construct overall flowsheet in order to support PEACER operation. The decontamination factor for transuranic elements was estimated based on both thermodynamic models and reported experimental data. It is expected that overall decontamination factor can be as high as 10{sup 5} for transuranic elements. Final wastes from pyrochemical processing for PEACER are noble metals, alkaline earth metal, and lanthanides. The final wastes are stabilized by mixing with zeolite and glass-frits such that concentration limit for class C waste can be met. The volume of Class C waste is estimated ...

Energy Technology Data Exchange (ETDEWEB)

Properties of photoconductive ultraviolet detectors fabricated on ZnO films were presented. Highly c-axis oriented ZnO films were grown on glass substrates by pulsed laser deposition. Ultraviolet photodetectors were fabricated based on metal-semiconductor-metal planar structures. The photoresponsivity and the quantum efficiency are much higher in the ultraviolet range than in the visible range, and the peak values are around 360 nm. Photocurrent transients show that the detector has a large photocurrent with the peak value of 2.8 mA, and a slow photoresponse with a rise time of 5 min and a decay time of 7 min. The response curve of the detector is fitted well with exponential curve. The large photocurrent should result from the both effects of the accumulation of conduction electrons and the decrease of the barrier height between crystallites. The relaxation time constant {tau} obtained from the curve fitting represents the time accumulation ...

International Nuclear Information System (INIS)

It has been carried out the magnetic properties determination for high iron oxide content glasses series obtained from a geothite red mud waste from the zinc hydrometallurgy and dolomite and glass cullet as main raw materials. It has been determined the magnetic susceptibility and magnetization values for the glasses here investigated. The results suggest that the magnetic behaviour are depending on the glass chemical composition, so that glasses can be differently classified like ferrimagnetic, ferromagnetic, superparamagnetic and paramagnetic. (Author) 6 refs.

Science.gov (United States)

... Problem: At a glass ceramic cooktop plant, workers manually lift uncut plates of glass onto a waist-high conveyor belt, where it is then stacked ...

KoreaScience (Korea)

Full Text Available

ScienceCinema

...introduced english ...the range of simple english ...the range of simple english ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

The glass gene is required for proper photo-receptor differentiation during development of the Drosophila eye glass codes for a DNA-binding protein containing five zinc fingers that we show is a transcriptional activator. A comparison of the sequences of the glass genes from two species of Drosophila and a detailed functional domain analysis of the Drosophila melanogaster glass gene reveal that both the DNA-binding domain and the transcriptional-activation domain are highly conserved between the two species. Analysis of the DNA-binding domain of glass indicates that the three carboxyl-terminal zinc fingers alone are necessary and sufficient for DNA binding. We also show that a deletion mutant of glass containing only the DNA-binding domain can behave in a dominant-negative manner both in vivo and in a cell culture assay that measures transcriptional activation. ...

British Library Electronic Table of Contents (United Kingdom)

The atomic mechanism of a glass-to-liquid transition in a monatomic Lennard-Jones (LJ) glass was studied using the molecular dynamics (MD) method. Glassy models were heated up from low temperature at two different heating rates and a glass-to-liquid transition found to occur at the higher heating rate. The temperature dependence of the potential energy, mean-squared-displacements (MSD) of the atoms and the self-intermediate scattering function indicate clearly that a glass transition occurs in the system. The atomic mechanism of the glass-to-liquid transition was investigated by analyzing the spatio-temporal arrangement of liquid-like atoms in the system upon heating. Liquid-like atoms were detected using the Lindemann-melting-like criterion. Upon heating, liquid-like atoms occur at temper...

International Nuclear Information System (INIS)

Thermal analysis testing revealed slight weight changes, which were a function of gamma irradiation, in a highly reduced Defense Waste Processing Facility (DWPF) simulated waste glass. Transmission electron microscopy (TEM) was performed on this glass to determine if the weight change corresponded to microstructural variations. TEM analyses showed that no microstructural changes were attributable to gamma irradiation. Exposure of the samples to the electron beam in the TEM did cause changes in the glass microstructures in some cases. These changes were likely due to localized heating of the glass due to interactions with the transmitted electrons.

British Library Electronic Table of Contents (United Kingdom)

The pentenary compound semiconductor Cu(In,Ga)(Se,S)2 is one of the most attractive materials for high-efficiency solar cells due to its tunable band gap to match well the solar spectrum. In this study, semiconducting Cu(In,Ga)(Se,S)2 thin films were prepared by a classical two-step growth process, which involves the selenization and/or sulfurization of In/Cu?Ga precursor. During the precursor formation step metallic In/Cu?Ga alloys were deposited onto the Mo-coated soda-lime glass substrates by DC magnetron sputter process. The respective precursors were subsequently reacted with H2Se and/or H2S gasses, at elevated temperatures. By optimizing the selenization parameters, such as the gas concentrations, reaction time, reaction temperature, and the flow of H2Se and H2S, high quality, single...

Energy Technology Data Exchange (ETDEWEB)

Beside traditional applications of refractory metals, e.g. in high temperature furnace construction, lighting or glass industry, one of the most important molybdenum products nowadays are large plates which are frequently used as targets for the sputtering of molybdenum layers in thin-film transistor liquid crystal displays. For the hot rolling of the sintered pre-material, the control over the recovery and recrystallization behavior is of particular importance. Molybdenum tends to a very recovery controlled behavior during hot deformation, at which the dislocations arrange into subcell boundaries instantaneously. These pronounced recovery processes seem to consume a large amount of the stored deformation energy for the actual recrystallization. On the other hand, recovery provides the future recrystallization nuclei. For a comprehensive characterization of these microstructural processes, electron microscopy appears to be the most proper ...

Energy Technology Data Exchange (ETDEWEB)

Building 922 houses all of SNL/California`s ES and H Departments: Health Protection, Environmental Protection, Safety, and Environmental Operations. It covers approximately 10,000 square feet and houses about 80 people. The office personnel generate nonhazardous solid office wastes in their daily activities. To determine the types and amounts of waste generated, a special PPOA sorting team sorted all of the trash collected from the building for a period of one-week (including paper and aluminum cans in the recycling bins). The team sorted the trash into major categories: paper, plastic, metals, glass, wet garbage, rest room waste, and miscellaneous materials. They then sorted it into subcategories within each major category. Rest room waste was collected but not sorted. The waste in each category was weighed separately. The total amount of trash collected during the week was approximately 168.8 kg (371.4 lbs). The results of this PPOA indicate ...

Energy Technology Data Exchange (ETDEWEB)

Moving out of the scientific community research laboratories, computational fluid dynamics (CFD) software packages are now allowing industrials to analyse and optimize industrial processes involving the use of gases, liquids and even some two-phase fluids. Their attractiveness and their impact stems out from the opportunity they offer to bring insight into an existing unit, or even at the design stage, by displaying the spatial distribution of process relevant variables such as temperature, concentration. The filling of the spacing in between a two-layer window is a simple example. This new opportunity of visualisation is at times an unique way, when the process environment is an opaque one, such as liquid metal flowing into a tundish or when measurements of flows may be a long and tedious work, such as flows within water treatment basins. This environment we are to investigate in order to optimize can also be a harsh one, due to its high temperature level for ...

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy (DOE) Subsurface Contamination Focus Area (SCFA) sponsored a technology demonstration of non-traditional in situ vitrification (NTISV) at Los Alamos National Laboratory (LANL). The project team for this demonstration included MSE Technology Applications, Inc., Geosafe Corporation, and LANL. The technology demonstration involved the performance of two large-scale test melts. The first, referred to as the ''cold'' test, was performed on a simulated absorption bed that contained surrogate contaminants. The cold test was conducted in April 1999. The second demonstration, referred to as the ''hot'' test, took place at LANL's Material Disposal Area (MDA) V in April 2000. The hot test was conducted on a portion of an absorption bed that received radionuclide and metal-contaminated wastewater from a laundry facility and a research laboratory from the mid-1940s to the ...

International Nuclear Information System (INIS)

Sodium-ion-conducting glasses are considered a promising alternative to the ceramic electrolytes. The glass upon which the most development work has been done is a sodium borate glass, which has an ionic resistivity of about 2 x 10/sup 4/ #OMEGA#-cm at 300"0C. Because of its high resistivity, cells using this borate glass require thousands of hollow glass fibers, each about 80 micrometers outer diameter (15 micrometer wall). In spite of its greater complexity, the cell with the glass electrolyte is of interest because of its potential for lower cost and higher power than the cell with ceramic electrolyte. Recently, silicate glasses of lower resistivity have been proposed for this application. These include: a soda-alumina-silica glass (900 #OMEGA#-cm at 300"0C), a soda-zirconia-magnesia-silica glass ...

Science.gov (United States)

A glass heat pipe is adapted for use as a solar energy absorber in an evacuated tube solar collector and for transferring the absorbed solar energy to a working fluid medium or heat sink for storage or practical use. A capillary wick is formed of granular glass particles fused together by heat on the inside surface of the heat pipe with a water glass binder solution to enhance capillary drive distribution of the thermal transfer fluid in the heat pipe throughout the entire inside surface of the evaporator portion of the heat pipe. Selective coatings are used on the heat pipe surface to maximize solar absorption and minimize energy radiation, and the glass wick can alternatively be fabricated with granular particles of black glass or obsidian.

UK PubMed Central (United Kingdom)

We demonstrate rapid fabrication of submicrometer-diameter pores in borosilicate glass using femtosecond laser machining and subsequent wet-etch techniques. This approach allows direct and repeatable...Full Text Available

CERN Document Server

565 deg C occurs when dissolution rate exceeds oxidation rate, exposing the fresh Al anode to the glass melt. Under inert atmosphere (at 583 deg C), air oxidation is not possible and galvanic cell redox reactions generate an excessive copper interlayer as the system attempts to sustain the oxide layer at the anode. Similar behaviour is observed in those coatings formed on the alloy using glass C (containing Al sub 2 O sub 3 and Na sub 2 O). In this case, the interfacial reactions involve the PbO of the glass and Pb-rich spherical precipitates are formed in the interfacial region, along side sodium aluminosilicate phases, precipitated from the PbO-depleted glass. The behaviour in both systems indicates that oxygen diffuses through the edge of the glass drop, from the atmosphere, to the substrate/glass interface. Coatings formed on the MMCs in air exhibited a ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

A sandwich construction, composed of hybrid carbon-glass fiber-reinforced plastic skins and a

Science.gov (United States)

... MATHEMATICAL PREDICTION, BODIES, SKIN(ANATOMY), SONIC BOOM, BIOPHYSICS, WOUND BALLISTICS, BONE FRACTURES, SKULL. ...

Science.gov (United States)

... The ultimate compressive strength (UCS) for the HMU/BSG composite is essentially equivalent to the tensile strength exhibited by this system. ...

International Nuclear Information System (INIS)

A systematic study for the materials design of III-V and II-VI compound-based ferromagnetic diluted magnetic semiconductors is given based on ab initio calculations within the local spin density approximation. The electronic structures of 3d-transition-metal-atom-doped GaN and Mn-doped InN, InP, InAs, InSb, GaN, GaP, GaAs, GaSb, AlN, AlP, AlAs and AlSb were calculated by the Korringa-Kohn-Rostoker method combined with the coherent potential approximation. It is found that the ferromagnetic ground states are readily achievable in V-, Cr- or Mn-doped GaN without any additional carrier doping treatments, and that InN is the most promising candidate for high-T_C ferromagnet. A simple explanation of the systematic behavior of the magnetic states in III-V and II-VI compound-based diluted magnetic semiconductors is also given. It is also shown that V or Cr-doped ZnS, ZnSe, and ZnTe are ferromagnetic without p- or n-type doping treatment. However, Mn-, Fe-, Co- or Ni-doped ...

Energy Technology Data Exchange (ETDEWEB)

As a continuation of our previous study, further experiments were performed on Li[sub 3]PO[sub 4]-Li[sub 2]S-SiS[sub 2] lithium ion conductive glass. In the present study, we employed a twin roller for quenching process instead of liquid nitrogen. We found that the glass forming region expands by twin roller technique and conductivity up to 1.5x10[sup -3] S/cm was achieved. Structural analysis on the glass revealed that Li[sub 3]PO[sub 4] doping changes the glass structure of Li[sub 2]S-SiS[sub 2], thereby enhancing the electrical conductivity

International Nuclear Information System (INIS)

The corrosion resistance of molybdenum, molybdenum disilicide, and a SiC_(_p_)/Al_2O_3 composite to molten E-glass at 1,550 C was studied. Mo showed no tendency to oxidize as it was immersed in soda-lime silicate glass in a parallel study. MoSi_2 was corroded by soluble molecular oxygen, leaving a Mo_5Si_3 interface behind. The SiC_(_p_)/Al_2O_3 composite was corroded at a more rapid rate wherein the SiC component was oxidized to form amorphous silica and CO bubbles. Based on these results, the activity of soluble molecular oxygen in E-glass was determined to be in the range of 2.4 x 10"-"1"4 to 2.0 x 10 "-"8.

International Nuclear Information System (INIS)

Tm3+ and Dy3+ ions co-doped aluminoborosilicate glasses were prepared in this study. The luminescence properties of the glasses were analyzed. A combination of blue, green, yellow, and red emission bands was shown for these glasses, and white light emission could be observed under UV light excitation. White light luminescence color could be changed by varying the excitation wavelength. Concentration quenching effect was investigated in this paper. Furthermore, the dependence of luminescence properties on glass compositions was studied. Results showed that the luminescence intensity changed with different network modifier oxides, while the white color luminescence was not affected significantly. - Graphical abstract: Tm3+ and Dy3+ ions co-doped aluminoborosilicate glasses, which emit white light under UV light excitation, were prepared. The dependence of luminescence properties on ...

British Library Electronic Table of Contents (United Kingdom)

In this paper, we present the photoluminescence properties of Pr3+-, Sm3+- and Dy3+-doped germanate glasses and glass ceramics. From the X-ray diffraction measurement, the host glass structure was determined. These glasses have shown strong absorption bands in the near-infrared (NIR) region. Compared to Pr3+-, Sm3+- and Dy3+-doped glasses, their respective glass ceramics have shown stronger emissions due to the Ba2TiGe2O8 crystalline phase. For Pr3+-doped glass and glass ceramic, emission bands centered at 530nm (3P03H5), 614nm (3P03H6), 647nm (3P03F2) and 686nm (3P03F3) have been observed with 485nm (3H43P0) excitation wavelength. Of them, 647nm (3P03F2) has shown bright red emission. Emission bands of 4G5/26H5/2 (565nm), 4G5/26H7/2 (602nm) and 4G5/26H9/2 (648nm) for the Sm3+:glass and gl...

Energy Technology Data Exchange (ETDEWEB)

Sintered glass-ceramics were produced from coal fly ashes, red mud from aluminum production and silica fume. The capabilities of Tuncbilek fly ash and a mixture of Orhaneli fly ash, red mud and silica fume to be vitrified and devitrified by sintering process were investigated by means of scanning electron microscopy and X-ray diffraction analysis. To determine the effect of binder in the sintering technique, glass powders were pressed without or with the addition of polyvinyl alcohol. Owing to microstructural observations, density and hardness measurements, it can be said that physical properties and the hardness of the produced samples strongly depended on the crystallization degree of the samples. Toxicity characteristic leaching procedure test results showed that glass-ceramic samples produced by using sintering technique could be considered as nonhazardous materials. Chemical durability of the sintered ...

International Nuclear Information System (INIS)

EPR and FT-IR absorption measurements have been performed for xCuO.(100-x)[2Bi2O3.B2O3] glass system, with 0?x?50 mol%. The mode in which the addition of the copper ions influences the structure of 2Bi2O3.B2O3 glass matrix was analyzed. The EPR absorption spectra revealed the presence in the glass structure of Cu2+ ions in axially distorted octahedral environments. EPR data pointed out the simultaneous presence of Cu2+ and Cu+ ionic species in the glasses with x?5 mol%. For x>10 mol%, the Cu2+ ions participate in the superexchange magnetic interactions, which increase with CuO content. The FT-IR spectra showed the presence of some bands that are assigned to vibrations of Bi-O bonds from BiO3 pyramidal and BiO6 octahedral units and B-O bonds from BO3 and BO4 units. The data obtained by these measurements reveal the structural changes in the 2Bi2O3.B2O3 glass matrix by controlled ...

Energy Technology Data Exchange (ETDEWEB)

A method for encapsulating and immobilizing waste for disposal. Waste, preferably, biologically, chemically and radioactively hazardous, and especially electronic wastes, such as circuit boards, are placed in a crucible and heated by microwaves to a temperature in the range of approximately 300{degrees}C to 800{degrees}C to incinerate organic materials, then heated further to a temperature in the range of approximately 1100{degrees}C to 1400{degrees}C at which temperature glass formers present in the waste will cause it to vitrify. Glass formers, such as borosilicate glass, quartz or fiberglass can be added at the start of the process to increase the silicate concentration sufficiently for vitrification.

Energy Technology Data Exchange (ETDEWEB)

New technologies make multi-megajoule glass lasers economically feasible. Laser architectures using harmonic switchout, target plane holographic injection, phase conjugation, continuous apodization and higher amplifier efficiencies have been devised. A plan for a multi-megajoule laser which can be built for an acceptable cost relies on manufacturing economies of scale and the demonstration of the new technologies presented here. These include continuous pour glass production, rapid harmonic crystal growth, switching of large blocks of power using larger capcaitors packed more economically and by using large identical parts counts.

International Nuclear Information System (INIS)

Single phase amorphous Al_xHf_1_0_0_-_x alloys with a wide amorphization range (33#<=#x#<=#75) were synthesized by the solid-state interdiffusion of pure polycrystalline Al and Hf powders at room temperature using a rod-milling technique. The mechanisms of metallic glass formation and competing crystallization processes in the mechanically deformed composite powders were investigated by means of X-ray diffraction, differential thermal analysis, scanning electron microscopy and transmission electron microscopy. The numerous intimate layered composite particles of the diffusion couples that formed during the first and intermediate stages of milling (0-173 ks) are intermixed to form amorphous phase(s) upon heating to about 980 K by so-called thermally assisted solid-state amorphization (TASSA). The amorphization heat formation for the binary Al_xHf_1_0_0_-_x system via TASSA, #DELTA#H"T"A"S"S"A_a, was measured directly as a function of the ...

Energy Technology Data Exchange (ETDEWEB)

A summary of the off-gas behavior in the HARVEST pot vitrification process is presented. Experimental runs were carried out on 3 representative wastes (MAGNOX - thermal reactor, metal fuel, THORP - thermal oxide fuel and PFR - fast reactor oxide fuel) using 2 methods of feeding the glass-formers (slurry and crizzle). Materials were carried over from the vitrification vessel into the off-gas system by entrainment supplemented by volatilization. The main volatile elements were Ru, B, Cs. Some volatility was also shown by Na and Li. The overall behavior of the off-gas was consistent with the presence in it of 5 separate aerosols of particulate matter. Sources of entrainment gave rise to 3 aerosols, and a further 2 aerosols were formed as a result of chemical reaction (Ru) and condensation (Cs) proceses involving the volatile species. Entrainment was enhanced when the feed contained free alkali nitrate. The Ru volatility correlated directly with ...

Energy Technology Data Exchange (ETDEWEB)

Aqueous radioactive high-level waste slurries are combined during processing steps that ultimately produce a stable borosilicate glass waste form. Chemically treated waste slurries are combined with each other and with glass frit-water slurries to produce the melter feed. Understanding the evolution of the rheological properties of the slurries is an important aspect of removing and treating the stored waste. To a first approximation, combinations of colloidal waste slurry with {approx}0.1-mm mean diameter glass frit or glass beads act in an analogous matter to slurries of spherical beads in Newtonian liquids. The non-Newtonian rheological properties of the waste slurries without frit, however, add complexity to the hydrodynamic analysis. The use of shear rate dependent apparent viscosities with the modified Einstein equation was used to model the rheological properties of aqueous frit-waste slurries.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

Science.gov (United States)

Not Available

International Nuclear Information System (INIS)

... dipole moments magnetic fields monocrystals neutron diffraction order-disorder

International Nuclear Information System (INIS)

Quantitative analytical electron microscopy study of dopant distribution in the microstructure of selected Nd-#alpha#-sialon samples revealed the presence of relatively large amounts of glassy phase at quadruple pockets, which exhibited a common composition similar to a melilite solution. Al segregants were depleted from adjacent grain boundaries to satisfy the 'stoichiometry' of such glass. Existence of this glass results in significant deviation of the Nd-#alpha#-sialon composition from the expected values, which shifts the #alpha#-#beta#-sialon phase boundary. Only extra Nd_2O_3 additives enable a monolithic #alpha#-sialon microstructure. The absence of similar glass in Yb-#alpha#-sialon materials keeps the phase relations from such deviations.

International Nuclear Information System (INIS)

Oxyfluoride aluminosilicate glasses in the composition of 50SiO2-20Al2O3-20LiF-10GdF3-0.5TmF3-xYbF3 (x = 0, 1.0, 2.5, 5, 7.5, 10, 15, 20, 25 and 30 mol%) have been prepared to study their thermal and optical properties. From the differential thermal analysis measurements, glass transition temperatures and onset crystallization temperatures have been evaluated and from them glass stability factors were calculated. Glass stabilities decreased gradually with fluoride content increment in all the studied glasses. The photoluminescence and decay measurements have also been carried out for all these glasses. In these glasses, an efficient near infrared quantum cutting with optimal quantum efficiency approaching 187% has been demonstrated, by exploring the co-operative downconversion mechanism from Tm3+ to Yb3+, with 467 nm (Tm3+ : 3H6 ? 1G4) ...

International Science & Technology Center (ISTC)

Metal Matrix Composites on the Basis of Nano-Materials

International Nuclear Information System (INIS)

The detection efficiency of a lithium glass detector was calculated using MCNP code, and the calculation was compared with the published results in Pulsed Sphere Plan. A lithium glass detector of our own was made, and its neutron efficiency was calculated. The calculated neutron efficiency was verified with both pulsed and steady DD neutrons. Characteristics of Neutron response of "6Li detector was discussed. (authors)

International Nuclear Information System (INIS)

A study of the 150-300 keV proton beam transmission through glass (borosilicate) tapered capillaries with different diameters of the input and output of the capillary was performed. The focusing effect was observed. The areal density of the transmitted beam is enhanced by approximately 20 times. It was shown that changing a taper angle from 0.5 deg to 1.7 deg evidences the increase of the transmission coefficient more than by 300 times keeping the initial energy spectrum of ions. (author)

Energy Technology Data Exchange (ETDEWEB)

The friction and wear properties of glass fiber reinforced composites of nylons (nylon 6, nylon 66 and nylon 46) with different crystallinities due to their molecular structures were investigated by sliding them with alumina ceramics and using a pin-on-disk friction machine. The friction coefficients of the glass fiber reinforced nylons in oil were lower and more stable than those in air from the initial stage of friction. The transfer of nylon matrix to adhere onto the alumina surface in air was so much greater than in oil that the alumina surface could not be recognized. Consequently, a different between the friction and wear properties in air and in oil was resulted. Reinforcement of nylons with glass fiber remarkably improved their friction properties in oil by its lubricating action, while the wears were rather high contrary to what was expected. This tendency was conspicuous for nylon 46 with high crystallinity. ...

Science.gov (United States)

"Precision manufacture of ceramic parts with CNC machining capability for aerospace, lasers, semiconductors and other industries. Materials include alumina, zirconia, glass, ferrites, silicon carbide, silicon nitride, sapphire, cordierite, mullite and others. A.C.T. has seen the number of applications and demand for high-realiability ceramics (aluminum oxide, zirconia, glass, ferrites, silicon carbide, silicon nitride, sapphire, cordierite, mullite, etc...) increase continually within the aerospace, computer and the industrial markets."

International Nuclear Information System (INIS)

Spectroscopic properties of Er"3"+ : CBS (CdSO_4 + B_2O_3 and R_2SO_4 + CdSO_4 + B_2O_3, R_2SO_4 = Li_2SO_4.H_2O, Na_2SO_4, K_2SO_4 and Gd_2(SO_4)_3.8H_2O) glasses are reported. The assigned energy level data of Er"3"+(4f"1"1) in these glasses are analysed in terms of a parametrized model Hamiltonian. The standard deviations of the data fits are between 39 and 47 cm"-"1 so that the energy level schemes of the Er"3"+(4f"1"1) ions in borosulphate (CBS) glasses are reasonably well reproduced. Radiative properties for the fluorescent levels of Er"3"+ : CBS glasses are determined by using the Judd-Ofelt theory. The potential laser transitions are identified with the help of predicted radiative properties which are compared and discussed with similar results. (author).

International Nuclear Information System (INIS)

This paper describes the development and a detailed analysis carried out on the luminescence characteristics of Pr"3"+ doped ZrF_4-BaF_2-LaF_3-YF_3-AlF_3-NaF glasses. In the present work our objectives are to elucidate the possible mechanisms that are responsible for NIR to red upconversion process and yellow to blue upconversion emission in terms of energy level schemes from the praseodymium containing fibre optical glass composition. We have studied their different physical and optical properties. Besides our investigation on the upconversion emission of these glasses, normal fluorescence studies have also been undertaken in explaining the mechanisms in demonstrating bright red and blue emissions upon excitations at visible and UV wavelengths. Besides these measurements works, a bright blue colour emission was observed under an UV source (202 nm) and upconverted prominent red emissions were observed with a laser diode (LD ...

International Nuclear Information System (INIS)

Glasses in the system (1 - x) [29Na2O- 4Al2O3- 67B2O3]- xZnO (0 ? x ? 35 mol%), have been prepared by the melt quenching technique. Elastic properties, X-ray and FT-IR spectroscopic studies have been employed to study the role of ZnO on the structure of the investigated glass system. Elastic properties and Debye temperature have been investigated using sound wave velocity measurements at 4 MHz at room temperature. The results showed that the density increases and the molar volume decreases while both sound velocities and the determined glass transition temperatures decrease with increase in x. X-ray and infrared spectra of the glasses reveal that the borate network consists of diborate units and is affected by the increase in the concentration of ZnO content. These results are interpreted in terms of the decrease in the N4 values (fraction of tetrahedral coordinated boron atoms), and substitution of ...

Energy Technology Data Exchange (ETDEWEB)

As a new composition of matter, alkali metal or ammonium or tetraalkylammonium diazidoperfluorophthalocyanatoferrate. Other embodiments of the invention comprise compositions wherein the metal of the coordination complex is cobalt, manganese and chromium.

Energy Technology Data Exchange (ETDEWEB)

We performed both a laboratory and field intercomparison of two novel glass-based retrospective radon detectors previously used in major radon case-control studies performed in Missouri and Iowa. The new detectors estimate retrospective residential radon exposure from the accumulation of a long-lived radon decay product, Pb-210, in glass. The detectors use track registration material in direct contact with glass surfaces to measure the alpha emission of a Pb-210 decay product, Po-210. The detector's track density generation rate (tracks cm{sup -2} hr{sup -1}) is proportional to the surface alpha activity. In the absence of other strong sources of alpha emission in the glass, the implanted surface alpha activity should be proportional to the accumulated Po-210 and hence, the cumulative radon gas exposure. The goals of the intercomparison were to: (1) perform collocated measurements using two ...

Science.gov (United States)

The dynamic dielectric susceptibility and the elastic compliance of the relaxor ferroelectric lanthanum lead zirconate titanate (PLZT) 9/65/35 have been measured under different cooling and heating protocols in order to study aging and memory. The memory of multiple aging stages at different temperatures has been found (several dips in the susceptibility curves on heating), as in spin glass systems below the glass transition. Remarkably, in PLZT the memory of several aging stages is retained also above the freezing temperature deduced from the dynamic susceptibilities. The results are discussed in light of the existing models of aging and memory in spin and dipolar glasses. PMID:15447139

Energy Technology Data Exchange (ETDEWEB)

Waste is a heterogeneous fuel, often with high levels of chlorine, alkali and heavy metals. This leads to much more severe corrosion problems than combustion of fossil fuels. The corrosion rates of the materials used can be extremely high. Materials used for heat transferring parts are usually carbon steel or low alloyed steel. These are significantly cheaper than other steels. Austenitic stainless steel is also used, but is often avoided due to its sensitivity to stress corrosion cracking. More advanced materials, such as nickel base alloys, can be used in extremely aggressive environments. Since these materials are expensive and do not always have sufficient mechanical properties, they are often used as coatings on carbon steel tubes or as composite tubes. A new method, which shows good results at the first tests in plants, is electroplating with nickel. Plastic materials can be used in low temperature parts if the temperature does not exceed 150 deg C. A ...

International Nuclear Information System (INIS)

Short communication.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

No abstract prepared.

International Science & Technology Center (ISTC)

Thermodynamic Stable Metal Compositions for Improvement of an Operational Safety of Constructional Materials under Conditions of Multifactor Loadings of an Aggressive Environment

International Science & Technology Center (ISTC)

Development of Bipolar Separator Plates with Porous Insertions of Metal Felt as Bearing Surfaces for Fuel Cell Electrodes

International Science & Technology Center (ISTC)

Studies of the Superheavy-metal Effect as a Stress-factor on Protein Biosynthesis and Cytoskeleton Integrity in Animal Cells

Science.gov (United States)

... TANK GUNS, GUNS, CHAMBERS, IGNITERS, INTERIOR BALLISTICS, INTERNAL PRESSURE, COMBUSTIBLE CARTRIDGE CASES, METALS. ...

UK PubMed Central (United Kingdom)

Quartz has a dissipation factor of approximately 10(-4), which is an order of magnitude less than that of the best glasses previously used to fabricate patch pipettes; it's dielectric constant of 3.8...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The structural change of the (100-x)(0.6Li[sub 2]S[center dot]0.4SiS[sub 2])centre dotxLi[sub 3]PO[sub 4] oxysulfide glassesduring crystallization was analyzed by means of solid-state nuclear magnetic resonance (NMR) and X-ray photoelectron spectroscopy (XPS). The unique tetrahedral units of SiO[sub n]S[sub 4-n] (n=1,2,3) and PO[sub n]S[sub 4-n] (n=1,2,3) present in the glass samples vanished and the SiS[sub 4], PS[sub 4], SiO[sub 4] units increased with proceeding of the crystallization process. Nonbridging sulfur and oxygen atoms decreased while bridging oxygens and S[sup 2-] increased with proceeding of the crystallization process. Large structural difference between the glass and the corresponding crystallized sample explained the high stability against crystallization found in the oxysulfide glass with the composition of X=5. (author)

UK PubMed Central (United Kingdom)

The phytochrome-mediated attachment of root tips of mung bean (Phaseolus aureus) and barley (Hordeum vulgare) to glass is affected by the prior exposure of hydrated...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Glass-ceramic materials containing 0-60% glass, 0-40% cordierite and 0-40% mullite were developed with dielectric constant lower than of Al{sub 2}O{sub 3} (5.2-6.7). The following glasses were used: SiO{sub 2}, CaO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-SiO{sub 2}, CaO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}, CaO-ZnO-B{sub 2}O{sub 3}, CaO-ZnO-Al{sub 2}O{sub 3}B{sub 2}O{sub 3}, BaO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-SiO{sub 2} and BaO-ZnO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-SiO{sub 2}. The influence of the content of the particular components on the value of dielectric constant of the ceramics was investigated. (author). 9 refs, 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

In order to clarify the alkali-resistance of fibers to be utilized as reinforcing materials for concrete, such as glass fiber, Aramid fiber, and carbon fiber, accelerated aging tests in alkaline solution were conducted. In detail, the degree of degradation of the fracture strength and Young's modulus were investigated through static tensile strength tests after soaking in alkaline solution of these fibers and then the mechanism of degradation was examined by observation using a scanning electron microscope. The conclusion obtained was as follows. Glass fiber was easily degraded in the alkaline solution and the progress of degradation was simulated quantitatively by the method proposed in this paper, which was based on a diffusion theory. Both Aramid fiber and carbon fiber showed a significant alkali-resistance without degrading. The reaction of glass fiber with alkaline solution proceeded uniformly from the surface ...

Energy Technology Data Exchange (ETDEWEB)

In the second part of this paper the author concludes his examination of the application of thermoplastic materials and also considers alumina ceramics, cast basalt and glass, rubbers, resins and wear-resistant steels

Science.gov (United States)

A short account is given of the difficulties encountered in temperature measurement of boundary layers and a comparison of two types of thermometers, an infrared radiometer and mercury in glass thermometer. (Author)

UK PubMed Central (United Kingdom)

It is well known that DNA strands bind to silica surfaces in the presence of high concentrations of chaotropic salts. We developed simple methods to evaluate binding and recovery of DNA on flat...Full Text Available

International Nuclear Information System (INIS)

Sialons are phases in the Si-Al-O-N and M-Si-Al-O-N systems where M includes Li, Mg, Ca, Sc, Y and the rare earth elements. They are comparable in variety with the mineral silicates and are built up of one-, two-, and three-dimensional arrangements of (Si,Al)(O,N)/sub 4/ tetrahedra in the same way that the structural units of the silicates are SiO/sub 4/ tetrahedra. These new materials include N-containing ceramics, glasses and glass-ceramics that are being explored for their thermal, chemical and physical properties.

International Nuclear Information System (INIS)

The fabrication of the ZT-40 torus, a large complex all-ceramic toroidal plasma containment vessel, is described. Several glass sealants covering the temperature range of 500 to 1300"0C, were developed and used to ''braze'' segments of the torus together, sapphire windows to the torus and the required pump-out and diagnostic parts to the ceramic vacuum vessel. Designs of window seals were developed that allowed sealing of the sapphire windows in a vertical position with minimum sealing glass flow.

Energy Technology Data Exchange (ETDEWEB)

EPR and FT-IR absorption measurements have been performed for xCuO.(100-x)[2Bi{sub 2}O{sub 3}.B{sub 2}O{sub 3}] glass system, with 0{<=}x{<=}50 mol%. The mode in which the addition of the copper ions influences the structure of 2Bi{sub 2}O{sub 3}.B{sub 2}O{sub 3} glass matrix was analyzed. The EPR absorption spectra revealed the presence in the glass structure of Cu{sup 2+} ions in axially distorted octahedral environments. EPR data pointed out the simultaneous presence of Cu{sup 2+} and Cu{sup +} ionic species in the glasses with x{>=}5 mol%. For x>10 mol%, the Cu{sup 2+} ions participate in the superexchange magnetic interactions, which increase with CuO content. The FT-IR spectra showed the presence of some bands that are assigned to vibrations of Bi-O bonds from BiO{sub 3} pyramidal and BiO{sub 6} octahedral units and B-O bonds from BO{sub 3} and BO{sub 4} units. The data ...

Energy Technology Data Exchange (ETDEWEB)

Long term integrated in situ experiments are performed in the HADES underground research facility (Mol, Belgium) in order to study the coupled reactivity between the different components of an underground repository for vitrified high level radioactive waste (HLW): glass, compacted clay, and stainless steel containers, at 90 degrees C and under gamma irradiation. Studies pertaining to the behaviour of silicon, a major element released during glass alteration, are presented here. Data collected from the integrated experiment, from simplified tests, and from modelling are put together, giving complementary information. The integrated experiment is used to investigate overall reactivity, whereas diffusion experiments coupled with modelling focused on the precipitation of silica in clay media. In the integrated in situ experiment, a bentonite clay (FoCa7) mixed with 5 wt.% of powdered glass frit was put in contact with ...

British Library Electronic Table of Contents (United Kingdom)

Statement of problem The opacity of the metal framework in metal ceramic restorations results in reduced light transmission through the tooth that diminishes the esthetics of the tooth. Purpose The purpose of this study was to investigate the color change that occurs apically to a metal ceramic restoration as a result of altering the metal framework design. Material and methods Color change relative to the unprepared tooth (DE) between various metal ceramic restorations was determined using computer imaging and CIELAB coordinates and compared to previously determined levels of clinical acceptability. Color change was evaluated by examining 2 conditions (the metal copings and the completed metal ceramic restorations), 4 framework designs (metal collar and porcelain margins with 0-mm, 1-mm, ...

Energy Technology Data Exchange (ETDEWEB)

The surface properties of copper-refractory metal (CU-RF) alloy bodies are modified by heat treatments which cause the refractory metal to form a coating on the exterior surfaces of the alloy body. The alloys have a copper matrix with particles or dendrites of the refractory metal dispersed therein, which may be niobium, vanadium, tantalum, chromium, molybdenum, or tungsten. The surface properties of the bodies are changed from those of copper to that of the refractory metal.

Energy Technology Data Exchange (ETDEWEB)

In the invar alloy (Fe{sub 0.65}Ni{sub 0.35}){sub 1-} {sub x} Mn {sub x} we measured the magnetic form factor s(Q) and the intermediate scattering function s(Q,t) for a sample close to the critical Mn concentration (x {sub c}=0.139), at which the sample turns to a re-entrant spin glass phase. The aim was to check whether the magnetic behaviour would approach the Q-independent relaxation behaviour of a classical spin glass when x=x {sub c}. The experiment showed a quite similar spin freezing as for a more ferromagnetic sample with x=0.113. The intermediate scattering function and the form factor were determined by paramagnetic NSE. The normalized scattering function S(Q,t)=s(Q,t)/s(Q)=exp[(-{gamma}t) {sup n}] was fitted by stretched exponential decay. As a function of temperature T<200 K the inverse time constant {gamma} showed the change of more than four orders of magnitude from frozen spin glass (T=60 K to T=100 ...

Energy Technology Data Exchange (ETDEWEB)

Glasses in the system (1 - x) [29Na{sub 2}O- 4Al{sub 2}O{sub 3}- 67B{sub 2}O{sub 3}]- xZnO (0 {<=} x {<=} 35 mol%), have been prepared by the melt quenching technique. Elastic properties, X-ray and FT-IR spectroscopic studies have been employed to study the role of ZnO on the structure of the investigated glass system. Elastic properties and Debye temperature have been investigated using sound wave velocity measurements at 4 MHz at room temperature. The results showed that the density increases and the molar volume decreases while both sound velocities and the determined glass transition temperatures decrease with increase in x. X-ray and infrared spectra of the glasses reveal that the borate network consists of diborate units and is affected by the increase in the concentration of ZnO content. These results are interpreted in terms of the decrease in the N{sub 4} values (fraction of ...

Energy Technology Data Exchange (ETDEWEB)

The leached glass is subject to leachant attack and results in surface layer alteration which greatly affects the corrosion progress of glass forms. This work studied the composition change, precipitation, pitting corrosion as well as surface layer break and spallation of the leached glass forms. 6 conclusions can be made: 1. The extent of surface layer alteration is related to many factors such as temperature, pH, leachant chemistry, flow rate and leach duration, etc. 2. The alkali element Na is seriously depleted and the elements like U.Ti,Fe, Ca and Mg are enriched in the surface layer. The influence of media has such order: Fe{sub 2}O{sub 3} > Na-bentonite > Zeolite. 3. The precipitate formed in leach test for 56 days at 90 {infinity}C is mostly amorphous, but after 91 days has crystallized. There is K - Ca - Al - Si crystal,the amount of Al, K and Si is increasing, but the amount of Ca is decreasing along ...

International Nuclear Information System (INIS)

High temperature fatigue crack growth (FCG) and creep crack growth (CCG) experiments have been conducted in air on weld metal, heat affected zone (HAZ) and base metal of the austenitic Alloy 800 and the nickel base Alloy 617. Tests were performed on specimens machined from pipes, in the temperature range 550-900 deg. C. The crack propagation mode was examined. At all temperatures and for both materials, FCG of base metal was found to be the highest, whereas the weld metal exhibited the lowest FCG rate. The FCG rate in the HAZ was found to lie in between of those observed for base and weld metal. The crack propagation mode remained transgranular in base metal and transdendritic in weld metal at all temperatures. CCG behaviour could be described using the energy rate integral C*. Base metal and weld ...

UK PubMed Central (United Kingdom)

The Δ- and Λ-isomerism of octahedral metal complexes is employed as a source of chirality for inducing chiral nematic phases. By applying a wide range of chiral metal complexes as a...Full Text Available

Science.gov (United States)

contaminated groundwater from the ASARCO metals refining facility ... ditch or creek crossing the ASARCO property at its northern end) and one at its ...

Science.gov (United States)

Magnetic Forming (10). - Forming of metals (the metal needs only to be an electrical conductor) is achieved without physical contact ...

Science.gov (United States)

Oct 15, 1985 ... Title: Laser-assisted solar cell metallization processing. No Digital Version Available: Go to Tips on Ordering ...

Science.gov (United States)

... No. 52. Metal Complexew-I. Preparation and Physical Properties of Transition Metal Complexes of 6-Mercaptopurine and ,-Mercapto-6, 7-Diphenyl ...

Science.gov (United States)

... No. 52. Metal Complexes-I. Preparation and Physical Properties of Transition Metal Complexes of 6-Mercaptopurine and 4-Mercapto-6, 7-Diphenyl ...

Energy Technology Data Exchange (ETDEWEB)

The durability of ball bearings, 32-mm- and 45-mm-bore, with a retainer or glass cloth-polytetrafluoroethylene (PTFE) laminate was tested under a high radial load at a speed of 20,000 rpm in LOX or LN2. The retainers were characterized as good self-lubricators because the abrasive glass-cloth fiber tips exposed on the retainer were chemicaly etched away with hydrofluoric acid (HF). During testing, the bearing-cartridge-acceleration was monitored to detect bearing damage. Testing in LOX for about 2.2 hr showed that excellent lubricating conditions were obtained for all bearings. Testing in LN2 for about 5.1 hr detected that the fatigue life of the bearing was about the same as the calculated B10 fatigue life. The HF chemical treatment resulted in a reacted fluoride-oxide material which remained in the etched part of the glass fiber. Several chemical products, particularly MgO, CaO, and CaCO3, enhanced adhesion of PTFE ...

International Nuclear Information System (INIS)

Iron oxide thin films were prepared by spray pyrolysis technique onto glass substrates from iron chloride solution. They were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and (UV-vis) spectroscopy. The films deposited at T _s #<=# 450 deg. C were amorphous; while those produced at T _s_u_b = 500 deg. C were polycrystalline #alpha#-Fe_2O_3 with a preferential orientation along the (1 0 4) direction. By observing scanning electron microscopy (SEM), it was seen that iron oxide films were relatively homogeneous uniform and had a good adherence to the glass substrates. The grain size was found (by RX) between 19 and 25 nm. The composition of these films was examined by X-ray photoelectron spectroscopy and electron probe microanalysis (EPMA). These films exhibited also a transmittance value about 80% in the visible and infrared range. The cyclic voltammetry study showed ...

International Nuclear Information System (INIS)

Thermoluminescence (TL) dosimetry was used to measure dose effects on the raw stock material of borosilicate container glass from different geographical locations. Effects were studied at times up to 60 days post-irradiation at doses from 0.15 to 20 Gy. The minimum detectable dose using this technique was estimated to be 0.15 Gy which is roughly equivalent to a 24 hr irradiation 1 cm from a 50 ng source of 60Co. Two peaks were identified in the TL glow curve, a relatively unstable peak around 125 C and a more stable peak around 225 C. Differences in TL glow curve shape and intensity were also observed for the glasses from different geographical origins. We investigate radiation induced defects in glass to further develop the technique of intrinsic dosimetry - the measurement of the total absorbed dose received by the walls of a container holding radioactive material. Intrinsic dosimetry is intended to be used as an ...

International Nuclear Information System (INIS)

A family of sealant materials has been developed for use in the solid oxide fuel cell (SOFC) and in other applications in the temperature range of 800 endash 1000 degree C. These materials are based on glasses and glass-ceramics in the SrO endash La_2O_3 endash Al_2O_3 endash B_2O_3 endash SiO_2 system. The coefficients of thermal expansion (CTE) for these materials are in the range of 8 endash 13x10"-"6/degree C, a good match with those of the SOFC components. These sealant materials bond well with the ceramics of the SOFC and, more importantly, form bonds that can be thermally cycled without failure. At the fuel cell operating temperature, the sealants have viscosities in the range of 10"4-10"6 Pa-s, which allow them to tolerate a CTE mismatch of about 20% among the bonded substrates. The gas tightness of a sample seal was demonstrated in a simple zirconia-based oxygen concentration cell. copyright 1996 Materials Research Society.

Science.gov (United States)

Two types of evacuated tube solar collectors have been operated in space heating, cooling and domestic hot water heating systems in Colorado State University Solar House I. An experimental collector from Corning Glass Works supplied heat to the system from January 1977 through February 1978, and an experimental collector from Philips Research Laboratory, Aachen, which is currently in use, has been operating since August 1978. A flat absorber plate inside a single-walled glass tube is used in the Corning design, whereas heat is conducted through a single glass wall to an external heat exchanger plate in the Philips collector. In comparison with conventional flat-plate collectors, both types show reduced heat losses and improved efficiency. For space heating and hot water supply in winter, the solar delivery efficiency of the Corning collector ranged from 49% to 60% of the incident solar energy. The portion of the space ...

International Nuclear Information System (INIS)

Phenolic resins have made a major breakthrough in the field of high technology in 80's. These are now active participants of "high tech' areas ranging from electronics, computers, communication, outer space, aerospace, advanced materials, bio materials and technology. A phenol - formaldehyde (1:1.5) resin having resin content of 70% synthesized in the laboratory has been applied for wood coating and reinforcing glass fiber. The weatherability and solvent resistance of these items have been studied and results discussed keeping in view the envisaged application for structural materials and chemical equipment. The toxic materials released during contact with solvents for chemical applications and during degradation general have been monitored. The results are discussed with reference to environmental pollution due to these resins and their composites under different conditions. (authors)

Energy Technology Data Exchange (ETDEWEB)

The thermal spike model has been successfully applied to track formation by swift heavy ions in insulators. Arguments are given supporting the assumption that the thermal spike mechanism is also valid for the anisotropic growth. The glass transition temperature is used as the main thermal parameter of the amorphous solids. Experimental results on the track formation in {alpha}-quartz and in crystalline Ni{sub 3}B and also on the anisotropic growth in Pyrex and Synsil glasses, in amorphous Pd{sub 80}Si{sub 20}, Ni{sub 3}B and Fe{sub 85}B{sub 15} are discussed. Good agreement is found with the predictions of the thermal spike model. (orig.).

CERN Document Server

The activity assay of a radiopharmaceutical administration to a patient is normally achieved via the use of a radionuclide calibrator. Because of the different geometries and elemental compositions between plastic syringes and glass vials, the calibration factors for syringes may well be significantly different from those for the glass containers. The magnitude of these differences depends on the energies of the emitted photons. For some radionuclides variations have been observed of 70 %, it is therefore important to recalibrate for syringes or use syringe calibration factors. Calibration factors and volume correction factors have been derived for the NPL secondary standard radionuclide calibrator, for a variety of commonly used syringes and needles, for the most commonly used medical radionuclide.

British Library Electronic Table of Contents (United Kingdom)

Objective.The objective of this study was to use the newly synthesized poly(quaternary ammonium salt) (PQAS)-containing polyacid to formulate the light-curable glass-ionomer cements and study the effect of the PQAS on the compressive strength and antibacterial activity of the formed cements.Materials and methods.The functional QAS and their constructed PQAS were synthesized, characterized and formulated into the experimental high-strength cements. Compressive strength (CS) and Streptococcus mutans viability were used to evaluate the mechanical strength and antibacterial activity of the cements. Fuji II LC cement was used as control. The specimens were conditioned in distilled water at 37 degrees C for 24 h prior to testing. The effects of the substitute chain length, loading as well as gra...

International Nuclear Information System (INIS)

The Hanford Waste Vitrification Plant Project has been established to convert the high-level radioactive waste associated with nuclear defense production at the Hanford Site into a waste form suitable for disposal in a deep geologic repository. The Hanford Waste Vitrification Plant will mix processed radioactive waste with borosilicate material, then heat the mixture to its melting point (vitrification) to forin a glass-like substance that traps the radionuclides in the glass matrix upon cooling. The Hanford Waste Vitrification Plant Quality Assurance Program has been established to support the mission of the Hanford Waste Vitrification Plant. This Quality Assurance Program Description has been written to document the Hanford Waste Vitrification Plant Quality Assurance Program.

Energy Technology Data Exchange (ETDEWEB)

Laser-induced phase-separation polymerization of a porous acrylate polymer is used for in-situ fabrication of dialysis membranes inside glass microchannels. A shaped 355 nm laser beam is used to produce a porous polymer membrane with a thickness of about 15 .mu.m, which bonds to the glass microchannel and forms a semi-permeable membrane. Differential permeation through a membrane formed with pentaerythritol triacrylate was observed and quantified by comparing the response of the membrane to fluorescein and fluorescently tagging 200 nm latex microspheres. Differential permeation was observed and quantified by comparing the response to rhodamine 560 and lactalbumin protein in a membrane formed with SPE-methylene bisacrylamide. The porous membranes illustrate the capability for the present technique to integrate sample cleanup into chip-based analysis systems.

Energy Technology Data Exchange (ETDEWEB)

We performed polarized neutron reflectometry (PNR) experiments on a 29 nm thick Au{sub 93}Fe{sub 7} film in a temperature range from 295 K down to 2 K in a vertical magnetic field up to 6 T. These high-field experiments were performed on the C5 spectrometer in Chalk River, Canada, using a split-pair cryomagnet. The magnetization as determined by PNR can be described with a Brillouin function from 295 K down to 50 K assuming the magnetic moment of isolated Fe atoms, i.e. 4{mu}{sub B} per Fe atom. Below 50 K the onset of the spin-glass freezing is observed as a strong deviation from this Brillouin type behavior of isolated atoms.

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

International Science & Technology Center (ISTC)

Development of the Technology to Obtain Pure Metal Scandium by Thermal Decomposition of Scandium Iodide

Energy Technology Data Exchange (ETDEWEB)

Pitting corrosion is localized accelerated dissolution of metal that occurs as a result of a breakdown of the otherwise protective passive film on the metal surface. This paper provides an overview of the critical factors influencing the pitting corrosion of metals. The phenomenology of pitting corrosion is discussed, including the effects of alloy composition, environment, potential, and temperature. A summary is then given of studies that have focused on various stages of the pitting process, including breakdown of the passive film, metastable pitting, and pit growth. 120 refs.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

A decrease of inhibitor concentration in a medium is always desirable even if the inhibitor is not toxic. In this connection, a sharp increase in the protective effect of certain corrosion inhibitors when cathodic polarization was applied to the metal is reviewed. The importance of a simultaneous account of the chemical structure of inhibitor and the nature of the metal corrosion under cathodic polarization is outlined. Some examples of applying this combined protection of metals are discussed.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

This patent describes the producing of a refractory metal wherein a sponge refractory metal is produced as an intermediate product by the use of magnesium with the incidental production of magnesium chloride, and wherein residual magnesium is separated from the magnesium chloride and from refractory metal to a vacuum distillation step which fractionally distills the magnesium, the magnesium chloride, and the metal sub-chlorides; the steps of: recovering fractionally distilled vapors of magnesium chloride and metal sub-chlorides from a sponge refractory metal; separately condensing the vapors as separately recovered; and recycling the separately recovered magnesium at a purity of at least about 96%.

Energy Technology Data Exchange (ETDEWEB)

Thermal hydraulics of a liquid metal is important to design the blanket of a magnetic confined fusion reactor. Since a liquid metal has high thermal and electrical conductivity, the flow characteristics are often different from those of an ordinary liquid like water especially in thermal convection and under a magnetic field. It is difficult to simulate such flows in a liquid metal cooled blanket by water. Flow visualization is a popular method to study thermal hydraulics. Since most of metals are visible by neutron rays, neutron radiography is available to the flow visualization of a liquid metal. The purpose of this study is to develop a visualization technique of the flow in a liquid metal by real-time neutron radiography using the tracer and the dye injection methods. A real-time thermal neutron radiography system of JRR-3M in Japan Atomic Energy Research ...

Energy Technology Data Exchange (ETDEWEB)

In order to develop the filler metal for Hastelloy alloy XR structure with thick wall, the weldability and high temperature strength properties of Hastelloy alloy XR weldment were investigated using the filler metals, which were alloy-designed on the basis of multiple regression analysis. The former was examined through the chemical analysis in the deposited metal, bend test, FISCO cracking test, optical microscopy and hardness measurement. The latter was investigated by means of tensile and creep test. It was found from these results that the crack susceptibility in the weldment was apparent to be lowered without degrading the high temperature strength properties. Therefore, it is concluded that these filler metals possess excellent performance as the filler metal for Hastelloy alloy XR structure with thick wall. (author).

British Library Electronic Table of Contents (United Kingdom)

Statement of problem Titanium is the most biocompatible metal used for dental casting; however, there is concern about its marginal accuracy after porcelain application since this aspect has direct influence on marginal fit. Purpose The purpose of this study was to determine the effect that metal selection and the porcelain firing procedure have on the marginal accuracy of metal ceramic prostheses. Material and methods Cast CP Ti, milled CP Ti, cast Ti-6Al-7Nb, and cast Ni-Cr copings (n=5) were fired with compatible porcelains (Triceram for titanium-based metals and VITA VMK 95 for Ni-Cr alloy). The Ni-Cr alloy fired with its porcelain served as the control. Photographs of metal copings placed on a master die were made. Marginal discrepancy was determined on the photographs using an image ...

Energy Technology Data Exchange (ETDEWEB)

Estuaries and coastal regions are highly variable in the physical and hydrographic conditions. As a result of heavy urbanization and industrialization of the head waters of most estuaries, there are substantial localized inputs of contaminants to the estuary. These factors combined with the flushing characteristics of individual estuaries to create relatively unique features that result in variation in the typical levels of trace metals for these systems. This makes intercomparison of the estuaries difficult. Comparability among estuaries becomes even more difficult when metals analyses are conducted without proper control of field and laboratory contamination, now firmly established in the trace metal analytical literature as a prerequisite for reliable marine trace metals analysis. This paper compares the concentrations of selected trace metal (Ag, Cd, Cu, Ni, Pb, and Zn) ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a process for preparing of an ion exchanger, comprising: treating an ionically inert activated charcoal porous support with an aqueous solution of metal oxychloride selected from the group consisting of zirconium and titanium oxychlorides so as to impregnate the pores of the support with the solution; separating the treated support from excess metal oxychloride solution; converting the metal oxychloride to a hydrous metal oxide precipitate in the pores of the support at a pH above 8 and above the pH whereat the hydrous metal oxide and activated charcoal support have opposite zeta potentials and sufficient to hydrolyze the metal oxychloride. It also describes a process for preparing an ion exchanger comprising: treating granulated activated charcoal with a concentrated solution of a metal oxychloride from the group ...

International Nuclear Information System (INIS)

Benthic invertebrates can uptake metals through diffusion of free ion solutes, or ingestion of sediment-bound forms. This study investigated the efficacy of the metal chelating resin SIR 300TM in adsorbing porewater metals and isolating pathways of metal exposure. A field experiment (Botany Bay, Sydney, Australia) and a laboratory toxicity test each manipulated the availability of porewater metals within contaminated and uncontaminated sediments. It was predicted that within contaminated sediments, the resin would adsorb porewater metals and reduce toxicity to invertebrates, but in uncontaminated sediments, the resin would not significantly affect these variables. Whereas in the laboratory, the resin produced the predicted results, in the field the resin increased porewater metal concentrations of contaminated sediments for at least 34 days ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Introduction - It is estimated that about 70-80% of the world's population relies on non-conventional medicine, mainly of herbal origin. However, owing to the nature and sources of herbal medicines, they are sometimes contaminated with toxic heavy metals such as lead, arsenic, mercury and cadmium, which impose serious health risks to consumers. It is critical to analyse source materials for heavy metals in order to ensure that their concentrations meet the related standards or regulations limiting their concentrations in herbal medicines. In this review, different analytical methods for analysis of heavy metals in herbal medicines are discussed. Objective - To provide a comprehensive review of the current state of the art in analytical methods used to detect heavy metals in herbal...

Energy Technology Data Exchange (ETDEWEB)

The themal neutron sensitivities of SEI and Toshiba FD-P10-7 radiophotoluminescent silver activated metaphosphate glass dosimeters have been measured and studied theoretically. The graphite thermal neutron column attached to the AEEW reactor NESTOR was utilised as a source of thermal neutrons with minimal fast neutron and gamma-ray contamination. Both the neutron removal and gamma correction measurement techniques were applied and these gave consistent results. It was found that the thermal neutron sensitivity of the Toshiba dosimeters is comparable to the most neutron intensitive thermoluminescent materials available. Because of their larger size and higher silver concentration, however, SEI dosimeters are an order of magnitude more neutron sensitive. The neutron sensitivity of FD-7 glass has not been reported previously, whereas in the case of SEI glass, there exists a modest body of previous work on dosimeters of ...

Energy Technology Data Exchange (ETDEWEB)

The article correlates CT and pathologic findings in 25 lung nodules with ground glass attenuation, which are small than 2 cm in diameter. They includes adenocarcinomas (Noguchi's classification type A, B, C) and a typical adenomatous hyperplasia. (author)

International Nuclear Information System (INIS)

This paper describes the use of numerical analysis for studying natural convection cooling systems for long term storage of heat producing radioactive materials, including special nuclear materials and nuclear waste. The paper explains the major design philosophy, and shares the experiences of numerical modeling. The strategy of storing radioactive material is to immobilize nuclear high-level waste by a vitrification process, convertion it into borosilicate glass, and cast the glass into stainless steel canisters. These canisters are seal welded, decontaminated, inspected, and temporarily stored in an underground vault until they can be sent to a geologic repository for permanent storage. These canisters generate heat by nuclear decay of radioactive isotopes. The function of the storage facility ventilation system is to ensure that the glass centerline temperature does not exceed the glass transition ...

Wastenet

... The products can be categorised as glazed flat-plate collectors, evacuated glass-tube collectors, and unglazed plastic or low temperature collectors. Glazed flat-plate collectors and vacuum tubes are widely used for solar water heating and space heating systems in all types of buildings. Unglazed plastic collectors are used exclusively for lower temperature applications, such as outdoor swimming pools or the agrarian business. Flat-plate solar collectors are likely to ...

Energy Technology Data Exchange (ETDEWEB)

Lithium ion conducting glass ceramics composed of the crystalline conductive phase Li{sub 1.4}Al{sub 0.4}(Ge{sub 1-x}Ti{sub x}){sub 1.6}(PO{sub 4}){sub 3}(x=0-1.0) with the Nasicon-type structure have been synthesized and characterized by DTA, X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and complex impedance techniques. The experimental results indicated that the glass ceramics were mainly composed of solid solution Li(Ge{sub 1-x}Ti{sub x}){sub 2}(PO{sub 4}){sub 3} formed by LiGe{sub 2}(PO{sub 4}){sub 3} and LiTi{sub 2}(PO{sub 4}){sub 3} in the whole x range and showed conductivity over 10{sup -4} S/cm at room temperature. The maximum room temperature lithium ion conductivity of 6.21x10{sup -4} S/cm with an activation energy as low as 0.32 eV was obtained for the Li{sub 1.4}Al{sub 0.4}(Ge{sub 0.67}Ti{sub 0.33}){sub 1.6}(PO{sub 4}){sub 3} treated at 950 C for 18 h. Mechanisms for the enhancement of {sigma}{sub ...

Energy Technology Data Exchange (ETDEWEB)

Radiation degradation of polycarbonate (PC) and polybutylene terephthalate (PBT) used as cable connector was evaluated using DSC, TGA, and mechanical properties. Glass transition temperature, melting temperature, 5% weight loss temperature, elongation at break, and tensile strength measurements were carried out for each of {gamma}-ray irradiated samples. In the results of those analyses, PC has radiation resistance better than PBT as a cable connector material.

Wastenet

... For more information regarding computer recycling visit www.recyclenow.com For further information on Recycling click on the links below Aluminium Recycling Charity Recycling Computer Recycling Clothes Recycling Ink Cartridge Recycling Local Recycling Home Composting Glass Recycling Mobile Phone Recycling Oil Recycling Plastic Recycling Recycling Bins ...

Energy Technology Data Exchange (ETDEWEB)

This paper investigates the spectral characteristics of three-dimensionally porous carbon dioxide indicators based on a porous silicate glass and phenolphthalein. The absorption spectra of the original solutions of phenolphthalein in alkaline and acid solutions are shown. The solutions were acidified by bubbling CO/sub 2/ through an alkaline phenolphthalein solution. The authors have succeeded in producing a reversible colorimetric adsorption indicator for carbon dioxide which after proper calibration enables the CO/sub 2/ content of an atmosphere to be estimated quantitatively.

Energy Technology Data Exchange (ETDEWEB)

Analysis of damages done by the radiation in a polymer characterized by optic properties of polished surfaces, of uniformity and chemical resistance that the acrylic; resistant until the 150 centigrade grades of temperature, and with an approximate weight of half of the glass. An objective of this work is the development of a method that analyze in automated form the superficial damages induced by radiation in plastic materials means an images analyst. (Author)

Energy Technology Data Exchange (ETDEWEB)

In this paper heavy metal pollution at an abandoned Italian pyrite mine has been investigated by comparing total concentrations and speciation of heavy metals (Fe, Cu, Mn, Zn, Pb and As) in a red mud sample and a river sediment. Acid digestions show that all the investigated heavy metals present larger concentrations in the sediment than in the tailing. A modified Tessier's procedure has been used to discriminate heavy metal bound to organic fraction from those originally present in the mineral sulphide matrix and to detect a possible trend of metal mobilisation from red mud to river sediment. Sequential extractions on bulk and size fractionated samples denote that sediment samples present larger percent concentrations of the investigated heavy metals in the first extractive steps (I-IV) especially in lower dimension size fractionated samples suggesting ...

Energy Technology Data Exchange (ETDEWEB)

A field survey on cadmium, lead, copper, and zinc was performed in Semarang, the fifth largest city in Indonesia. Water, sediment, and fish samples were collected from 101 grids of 2 x 2 km. The objectives of the study were (1) to identify the spatial distribution of metals in the sediments of the greater Semarang area, (2) to estimate the background concentrations of the metals present in Semarang, (3) to provide a simple tool for deriving standards for metals in the sediment, and (4) to explore the potential use of the guppy (Lebistes reticulatus) as a bioindicator of urban metal pollution. To map the spatial distribution of the metals, concentrations of each metal in sediment were plotted against the corresponding city coordinate. On the basis of these plots, background concentrations of the metals were estimated. A combined pollution ...

Energy Technology Data Exchange (ETDEWEB)

W have introduced template-synthesized metal phosphate nanoparticle labels for electrochemical immunoassay. Such use of an apoferritin template offers a simple and convenient route to prepare metallic nanoparticle labels for electrochemical immunoassays and avoid the complicated and time-consuming nanoparticle synthesis process (QD synthesis). Releasing metal ions from metal phosphate in an acetate buffer (pH 4.6) eliminates the harsh condition in the traditional metallic nanoparticle dissolution (e.g., strong acid dissolution of QDs and gold nanoparticles). This method is ultrasensitive and its DL is low to 77fM. The simultaneous detection of multiple protein targets is easily performed by using different metal phosphate nanoparticle labels (cadmium phosphate and lead phosphate). This approach can be extended to prepare multiple metal (such ...

British Library Electronic Table of Contents (United Kingdom)

Metal iodates with a lone-pair containing I(V) that is in an asymmetric coordination geometry can form a diversity of unusual structures and many of them are promising new second homonic generation (SHG) materials. They exhibit wide transparency wavelength regions, large SHG coefficients and high optical-damage thresholds as well as moderately high thermal stability. In this paper, the structures and properties of the metal iodates are reviewed. The combination of d0 transition-metal cations with the iodate groups afforded a large number of metal iodates, with cations covering alkali metal, alkaline earth and lanthanide elements. Many of them are noncentrosymmetric (NCS) and display excellent SHG properties due to the additive effects of polarizations from both types of the asymmetric unit...

British Library Electronic Table of Contents (United Kingdom)

Iron, zinc, copper and manganese are essential metals for cellular enzyme functions while cadmium, mercury and the metalloid arsenic lack any biological function. Both, essential metals, at high concentrations, and non-essential metals and metalloids are extremely reactive and toxic. Therefore, plants have acquired specialized mechanisms to sense, transport and maintain essential metals within physiological concentrations and to detoxify non-essential metals and metalloids. This review focuses on the recent identification of transporters that sequester cadmium and arsenic in vacuoles and the mechanisms mediating the partitioning of these metal(loid)s between roots and shoots. We further discuss recent models of phloem-mediated long-distance transport, seed accumulation of Cd and As and rec...

Energy Technology Data Exchange (ETDEWEB)

A metal matrix is inserted into a phase-change material to enhance the heat transfer during phase-change processes. The metal matrix tends to act like a heat transfer fin from the heated or cooled surface and to increase the effective thermal conductivity of the phase-change fluid. The scope of the study involves numerically modeling the heat transfer to and from constant-temperature cylindrical tubes surrounded by water during the freezing and melting processes. Comparisons of heat transfer with and without the metal matrix are made, with different porosities and densities of the metal matrix being examined. The results of this study are discussed in terms of the effectiveness of the metal matrix as a heat transfer enhancement device.

Energy Technology Data Exchange (ETDEWEB)

The green mussel Perna viridis and the clam Ruditapes philippinarum have been frequently used as biomonitors of coastal contamination in subtropical and tropical waters, yet the physiological processes controlling metal uptake in these bivalves are unknown. Assimilation efficiency (AE) is an important physiological parameter quantifying metal bioavailability from ingested food. The authors determined the AEs of Cd, CR, and Zn in these bivalves feeding on five species of phytoplankton and one natural section. The influences of the cytoplasmic distribution of metals in the algal cells and the digestive physiology of bivalves on metal AEs were also examined. Among the three metals, Zn was generally assimilated at the highest efficiency, i.e., 21 to 36% in the mussels and 29 to 59% in the clams. Cr was the least assimilated metal, with AEs being 10 to 16% in the ...

UK PubMed Central (United Kingdom)

Disposable nappies (diapers) have been satisfactorily demineralized and used for the collection of excreta from infants and young children during mineral and trace metal balances. It was possible to...Full Text Available

UK PubMed Central (United Kingdom)

We have developed a method to extract and separate phytochelatins (PCs)—metal(loid) complexes using parallel metal(loid)-specific (inductively coupled plasma-mass spectrometry) and organic-specific...Full Text Available

International Nuclear Information System (INIS)

The variation in the superconducting properties of various binary alloys of transition metal-germanium systems was surveyed by studying sputter deposited samples prepared under various conditions. The primary interest has been to study the formation of the stoichiometric A-15 compounds T_3Ge.

Energy Technology Data Exchange (ETDEWEB)

This paper addresses one source of degradation in OPV devices: the metal/organic interface. The basic approach was to study the completed device stability vs. the stability of the organic film itself as shown in subsequent devices fabricated from the films.

UK PubMed Central (United Kingdom)

BackgroundAirway complications are among the most challenging problems after lung transplantation, and Self-Expandable Metallic Stents (SEMS) are used to treat airway complications...Full Text Available

UK PubMed Central (United Kingdom)

The response of the dissimilatory metal-reducing bacterium Shewanella alga BrY to carbon and nitrogen starvation was examined. Starvation resulted in a gradual decrease in the mean cell volume from...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Objective is to study the effects of local structure, interatomic forces, and atom size on the mobility of metal atoms in amorphous silica and at the silica surface. EXAFS studies of Zn and Pt in silica are reported. (DLC)

British Library Electronic Table of Contents (United Kingdom)

The estimation of numerical values of the mean distance of closest approach of ions, a, of alkaline-earth metal ion salts in aqueous solutions, determined from activity coefficients, as well as from different theoretical approaches, is presented and discussed.

Energy Technology Data Exchange (ETDEWEB)

Laser-assisted processing techniques for producing high-quality solar cell metallization patterns are being investigated, developed, and characterized. The tasks comprising these investigations are outlined.

Energy Technology Data Exchange (ETDEWEB)

The biological accumulation of heavy metals and cesium, strontium, and uranium in plants is discussed. The role of nutrient deficiencies and foliar treatments of manganese and iron compounds is described.

International Nuclear Information System (INIS)

A mathematical interaction model, validated by experimental results, was developed to modeling the metal uptake by plants and induced growth decrease, by knowing metal in soils. The model relates the dynamics of the uptake of metals from soil to plants. Also, two types of relationships are tested: total and available metal content. The model successfully fitted the experimental data and made it possible to predict the threshold values of total mortality with a satisfactory approach. Data are taken from soils treated with Cd and Ni for ryegrass (Lolium perenne, L.) and oats (Avena sativa L.), respectively. Concentrations are measured in the aboveground biomass of plants. In the latter case, the concentration of metals in different parts of the plants (tillering, shooting and earing) is also modeled. At low concentrations, the effects of metals are moderate, and ...

Energy Technology Data Exchange (ETDEWEB)

A process for the generation of halogens from halide-containing solutions includes the step of conducting electrolysis of the solutions in an electrolytic cell having a platinum based amorphous metal alloy anode.

Science.gov (United States)

This cost-effectiveness analysis supports the proposed effluent limitations guidelines and standards for the Metal Products and Machinery Industry (MP and M) Phase I Industry. The report assesses the cost-effectiveness of five regulatory options for indir...

UK PubMed Central (United Kingdom)

Physical system conceptual models are developed to illustrate the various interconnecting pathways of metal flow. Economic use of mercury and cadmium, as representative toxic heavy metals, is inventoried,...Full Text Available

Science.gov (United States)

...visible damage. (k) Corrosion resistance. Each metal part of a...evidence of salt-spray corrosion resistance equal to or greater than...sample of test metal must show corrosion resistance equal to or better than...

Science.gov (United States)

We studied a novel universal spectrochemical series of six-coordinated octahedral 3d transition metal complexes, which can be used for any combination of central metal atom and ligand molecules. A two dimensional spectrochemical series could be used to estimate the ligand field splitting energy of not only known compounds but also the unknown compounds. Therefore, it should be possible to control the physical properties, such as the electronic and magnetic properties and the optical phenomena of octahedral transition metal complexes by modifying the ligand field splitting. PMID:19378561

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

This study is an evaluation of the potential environmental impacts of contaminated groundwater from the ASARCO metals refining facility adjacent to the ...

Science.gov (United States)

... Descriptors : *PROTECTIVE COATINGS, *WATER REPELLENTS, *COMBUSTIBLE CARTRIDGE CASES, COMPUTER PROGRAMS, SOLVENTS ...