International Nuclear Information System (INIS)

Ten different alloys of zirconium have been tested with regard to the effect of irradiation on their mechanical properties and their sensitivity to environmentally induced failure. Two different environments were used: iodine vapour and liquid cesium with an addition of 2% cadmium. The neutron dose was 10"2"1n/cm"2 (E>1MeV) and the irradiation temperature was about 300 degrees C. All alloy additions increased the irradiation hardening. Especially notable was the large effect of titanium and tin on irradiation hardening. A limited amount of transmission electron microscopy was carried out in order to find an explanation to the effects. The testing in different environments showed that there is no clear correlation between environmental sensitivity and yield stress. For materials of similar yield stress an alloyed material tends to be more sensitive to environmental cracking than a material which only ...

Energy Technology Data Exchange (ETDEWEB)

The initiation and inhibition of pitting corrosion on zirconium and hafnium in aqueous solutions have been investigated by potentiodynamic, potentiostatic and galvanostatic measurements at 25/sup 0/C. Effects of Cl/sup -/, Br/sup -/and I/sup -/ have been examined over a range of salt concentrations and pH. All three halide ions cause pitting attack on the two metals, but this may be inhibited by other anions. The results show that hafnium is more easily protected against pitting than is zirconium. The data are treated by the Butler-Volmer equation to yield more information about the mechanisms of the pitting corrosion.

Energy Technology Data Exchange (ETDEWEB)

The kinetics of the reaction of zirconium phosphates with carbon tetrachloride in sodium and potassium chloride melt as well as the effect of temperature, gas flow, solubility and weight of the solid phase of the phosphate, and stirring of the melt on the chlorination rate has been studied. The kinetic parameters of the reaction (rate constants, activation energy, etc.) have been calculated.

Science.gov (United States)

The interaction of Pu(IV) and Zr(IV) with citric acid in nitric acid solutions (C/sub HNO/sub 3// greater than 0.1 M) of lithium nitrate was studied by the distribution method in the interval of nitrate ion concentrations from 1 to 6 g-eq/liter. A 40 percent solution of TBP in decane was used as the extraction reagent. It was established that within the range of concentrations studied, complex compounds of plutonium and zirconium are formed: PuHCit/sup 2 +/ and ZrH/sub 2/Cit/sup 3 +/. The concentration equilibrium constants of the reactions of formation of these compounds retain a constant value at constant ionic strength and undergo substantial variation when the total concentration of the nitrate ion in solution is varied. The values of the effective equilibrium constants, calculated considering the change in the activity coefficient of the hydrogen ion, retain a constant value within a wide range of nitrate ion concentrations. It was shown ...

International Nuclear Information System (INIS)

Current trends in nuclear power generation (and particularly in pressurized water reactors) are toward plant life extension and extended fuel burnup. A higher heat generation rate can induce local boiling regimes at the fuel rod surface in the hottest channels of the core, which can strongly modify the chemical environment of the cladding and influence the oxidation rate of zirconium alloys. Tests performed in out-of-pile loops under severe chemical and thermal-hydraulic conditions (nucleate boiling, higher lithium contents compared to PWRs) reveal two important phenomena: an increase of the oxidation rate of Zircaloy-4 cladding materials in 'high' lithiated environments; an enrichment of the chemical additives in the primary water (boron, lithium) at the surface of the cladding under nucleate boiling conditions. The latter phenomenon, also called 'hideout effect', is mainly controlled by some thermal hydraulic parameters ...

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The desire to increase uranium utilization and to minimize spent fuel storage requirements provides an incentive to extend the average fuel rod discharge burnup to about 70,000MWd/MTU. For these higher burnups data are needed to determine if waterside corrosion of the cladding may be a life-limiting feature of fuel rod design. It is apparent that many factors can influence waterside corrosion, and these need to be better understood in order to minimize corrosion at these higher target burnups. The objective of this report is to review published data relevant to the corrosion of Zircaloy under PWR operating conditions. (author). 100 refs., 4 tabs., 21 figs.

Energy Technology Data Exchange (ETDEWEB)

The electrogeometric model cannot consider the influence of some parameters on the screening of the wire conductor of the H.V. lines. For analysing the influence of these parameters (the conductor potential, the influence of the distance from phase conductor to earth wire, the influence of the reducing factor of the striking earth distance, the earth slope, etc.), the Monte Carlo method is preferable. The influence of the earth slope on the screening effect of the wire conductor for different conditions is presented in this paper. (author)

International Nuclear Information System (INIS)

Ionizing radiations that differ in number, size, and distribution of energy deposition events might be expected to cause different effects for the same absorbed dose. Furthermore, microdosimetry calculations suggest that large variations in biological effectiveness might be expected for internally deposited alpha-emitting radionuclides for the same absorbed dose, depending upon the specific activity and spatial distribution of the sources in tissue. The study described in this article was designed to demonstrate these phenomena in vitro. Cultured Chinese hamster ovary (CHO-K1 BH4) cells were exposed in vitro to inert, insoluble ceramic microspheres in zirconium dioxide labeled with "2"3"9Pu. The average exit energy of the 5.15 MeV alpha particle was calculated to be 4.3 MeV. Exposure times varied from four to seven hours to achieve the desired dose level.

British Library Electronic Table of Contents (United Kingdom)

Abstract Within the framework of the CRC 799 -TRIP-Matrix-Composites- at the TU Bergakademie Freiberg new composite materials consisting of TRIP steel and zirconium dioxide ceramics are designed in a powder route and a casting route. To manufacture faultless samples basic investigations of the feeding and infiltration behaviour within macro porous ceramics such as filters were needed. The effects of bottom pouring and top pouring were investigated as well as the effects of different preheating temperatures, contents of phosphorous in the steel and flow trough rates. Bottom pouring corrupts the feeding mainly of filters with high ppi (pores per inch). Top pouring improves the feeding, but generates inhomogeneous infiltration qualities, which can affected and enhanced by a increasing preheat...

British Library Electronic Table of Contents (United Kingdom)

Spherical nano-sized YSZ (yttria stabilized ZrO2) powders were successfully synthesized via a reverse microemulsion system. The water droplets in the microemulsion system of yclohexane/water/span85/Triton X-100/hexyl alcohol can act as the nano-reactors which solubilize zirconium oxychloride and ammonia water separately. The minute original reactors are favor to the formation of nano-sized spherical YSZ powders and the dispersibility of the powders can be controlled effectually by adjusting the weight ratio of the LiNO3 molten salt to the precursor. The phase transformation from cubic to monoclinic starts at and 500??C and finally monoclinic and cubic phase with increased crytallinity coexist at 800??C. The effect of LiNO3 molten salt in the formation of YSZ powders was also discussed.

International Nuclear Information System (INIS)

Zirconium is a transition element located along with sister elements titanium and hafnium in Group IVB of the periodic table. It is grayish white metal, with a density somewhat less than carbon steel. Zirconium is the ninth most common metallic element in the earth's crust, and is more abundant than zinc, lead, nickel, or even copper. Zirconium is exceptionally resistant to corrosion by many common acids and alkalis. It is resistant to most organic acids, such as formic, acetic, lactic, and oxalic acids. It also has a high resistance to localized forms of corrosion, such as pitting, crevice corrosion, and stress corrosion cracking. Its corrosion resistance is caused by the formation of a dense, tenaciously adherent, chemically inert oxide film on the surface. This oxide film protects the base metal from both chemical and mechanical attack at temperatures up to about 400 C (750 F). This article describes ...

Energy Technology Data Exchange (ETDEWEB)

It is shown that plasma viscosity does not influence the magnetic island rotation directly. Nevertheless, it leads to nonstationarity of the plasma velocity. This nonstationarity is the reason of the viscosity effect on island rotation. (author)

UK PubMed Central (United Kingdom)

AIM: To evaluate the effects of ginger on gastric motility and emptying, abdominal symptoms, and hormones that influence motility in dyspepsia.METHODS: Eleven patients with functional dyspepsia...Full Text Available

International Nuclear Information System (INIS)

Zirconium-base alloys are used primarily as fuel cladding material and other core structure material in water cooled nuclear power reactors. Main research achievements and problems about corrosion of zirconium alloys are reviewed; the present theories and challenge are summarized. In the 1980s, great progress had been made towards correlating alloy composition, microstructure and irradiation with corrosion resistance. In the 1990s, main researches are focused on exploring actual mechanism of corrosion, optimizing both alloy composition and microstructure in order to minimize the fuel cycle costs through burnup optimization.

International Nuclear Information System (INIS)

The present invention concerns a method of evaluating corrosion resistance of a zirconium alloy easily and in a short period of time. An anode polarization curve of the zirconium alloy is measured to obtain an anode polarization curve expressed by logarithm. The curve is converted to a potential-current density curve expressed by absolute values. The peak area in the curve of the converted potential-current density is indicated by numerical values. Further, the corrosion resistance of the zirconium alloy is evaluated based on the peak area converted into the numerical values as a reference. This method is based on the finding that the peak area has a close relation with nodular corrosion resistance, and the corrosion resistance can be judged with respect to a specific zircaloy-2. (T.M.).

Energy Technology Data Exchange (ETDEWEB)

Propylene polymerizations were carried out with {phi}{sub 2}C(Flu)(Cp)ZrCl{sub 2} and SiMe{sub 2}(Ind)2ZrCl{sub 2} catalysts supported on silica, zeolite sodic mordenite (NaM) and acid mordenite (HM). The polymerizations were performed at different temperatures and varying aluminium/zirconium molar ratios ([Al]/[Zr]). The effect of these reaction parameters on the catalyst activity was investigated using a proposed statistical experimental planning. In the case of f{sub 2}C(Flu)(Cp)ZrCl{sub 2}, SiO{sub 2} and NaM were used as support and the catalyst performance evaluated using toluene and pentane as polymerization solvent. The molecular weight, molecular weight distribution, melting point and crystallinity of the polymers were examined. The results indicate very high activities for the syndiospecific heterogeneous system. Also, the polymers obtained had superior Mw and stereo regularity. (author)

Energy Technology Data Exchange (ETDEWEB)

During 17 years since the start of operation of the first commercial LWR in Japan, many LWRs have experienced various corrosion damages, but the causes of them were clarified, and the counter-measures were executed effectively in actual plants, as the results, the cause of corrosion damage decreased remarkably, and now, the high rate of operation has become to be maintained. In this paper, the major cases of corrosion damage experienced in LWRs in Japan and foreign countries, the causes of them and the countermeasures, the problems of hereafter and so on are described. The corrosion damage of metallic materials in the environment of LWRs occurs in the parts in contact with high temperature, high pressure water and steam, such as stainless steel piping in the primary cooling system of BWRs, and nickel alloy heating tubes of steam generators, carbon steel feed water piping and zirconium alloy fuel cladding tubes in PWRs. Recently, accompanying ...

International Nuclear Information System (INIS)

The present state of knowledge on the influence of stray radiation on image quality and its physical description and quantification is summarized. Experimental results on the influence of physical parameters on the fraction of scattered radiation and the effect of scatter reduction by air gap technique and secondary radiation grids are committed. Open theoretical and practical problems and the limitations of common methods of scatter reduction are pointed out. (author).

International Nuclear Information System (INIS)

Using the PMR method the interaction of zirconium and hafnium tetrachlorides with tri.tet.butylphenyl ester of 1,2- naphthoquinonediazide (2)-5-sulfonic acid is studied. The formation of MCl_4xNQD complexes is established, the equilibrium constants and thermodynamic parameters of complexing reaction are determined. The presence of rapid ligand exchange, proceeding according to associative mechanism, is detected. The rate constants and activation energies of the exchange reaction are calculated.

Energy Technology Data Exchange (ETDEWEB)

An energy dispersive x-ray fluorescence technique was used for the determination of Titanium (Ti) and Zirconium (Zr) in red mud by using a standard addition method. An annular {sup 241}Am source is employed for excitation of K shells of elements. 13 refs., 2 figs., 1 tab.

UK PubMed Central (United Kingdom)

This paper examines theoretically the effects that restraints on the tertiary structure of a superhelical DNA domain exert on the energetics of linking and the onset of conformational transitions. The...Full Text Available

Science.gov (United States)

... WHS- Washington Headquarters Service. ... The dynamic Joint Special Operations Task Force -- Philippines (JSOTF-P) has evolved and ...

UK PubMed Central (United Kingdom)

Aerosol particles are ubiquitous in the troposphere and exert an important influence on global climate and the environment. They affect climate through scattering, transmission, and absorption of...Full Text Available

International Nuclear Information System (INIS)

Substantial roles of precipitates such as Zr-Fe-Cr type intermetallic compounds on uniform corrosion and hydrogen pickup of zirconium alloys in pure water autoclave tests were investigated from an electrochemical point of view. This paper describes the roles on corrosion. A corrosion test on precipitate-containing and precipitate-free materials made from pure zirconium and a small quantity of iron and chromium, rest potential measurements on an intermetallic compound of Zr(FeCr)_2 and zirconium matrix, and a galvanic coupling test of those were performed. Results showed that corrosion behavior of zirconium alloys could be attributed to the electrochemical properties of intermetallic compounds precipitated in each alloy. Namely, the cathodic and anodic polarization characteristics were associated with anodic protection provided by the precipitates on the alloys and the precipitates degradation in the ...

Environmental Research Database

DescriptionThe overall aim of this application is to examine experimentally environmental influences on the pattern of senescence in birds. We plan to experimentally uncouple chronological age and reproductive effort and examine their effects on reproductive performance and lifespan. We also plan to examine experimentally how these relationships are influenced by nutritional conditions during early development. We will combine the organismal fitness measures of lifespan and reproductive performance with me [continued...

UK PubMed Central (United Kingdom)

Performance on serial tasks is influenced by first- and higher-order sequential effects, respectively due to the immediately previous and earlier trials. As response-to-stimulus interval (RSI)...Full Text Available

International Nuclear Information System (INIS)

A survey is given of the influence of surface deformations on heavy ion reactions. Emphasis is put on the effect of zeropoint fluctuations in the entrance channel and on the effect on grazing collisions in terms of an imaginary part of the scattering potential. (orig.).

Science.gov (United States)

The development of comfort in buildings throughout the centuries was influenced by the demand for progress, wealth and innovation in various respects. At present, it seems that progress may only be possible by taking into account the environment and creat...

British Library Electronic Table of Contents (United Kingdom)

Zirconium and particularly Zr-2.5wt%Nb (Zr2.5Nb) alloy are useful for engineering bearing applications because they can be oxidized in air to form a hard surface ceramic. Oxidized zirconium (OxZr) due to its abrasion resistant ceramic surface and biocompatible substrate alloy has been used as a bearing surface in total joint arthroplasty for several years. OxZr is characterized by hard zirconium oxide (oxide) formed on Zr2.5Nb using one step thermal oxidation carried out in air. Because the oxide is only at the surface, the bulk material behaves like a metal, with high toughness. The oxide, furthermore, exhibits high adhesion to the substrate because of an oxygen-rich diffusion hardened zone (DHZ) interposing between the oxide and the substrate. In this study, we demonstrate a two step pro...

International Nuclear Information System (INIS)

The methods of surface modification of Ti-Zr alloy by laser treatment are considered. Characteristics of laser modification without- and with surface melting and with melting in different gaseous environments and with nickel microalloying are presented. Maximum depth, hardness and corrosion resistance are observed under nickel laser alloying.

Energy Technology Data Exchange (ETDEWEB)

Using an expanded nuclear data base, the activation of nitrogen, aluminum, iron, nickel, copper, zirconium, niobium, molybdenum, tungsten, and lead were calculated for the first wall positions of the STARFIRE and MARS conceptual fusion reactors.

International Nuclear Information System (INIS)

Possible causes of forest damage are discussed. Mapping of affected areas by various workers resulted in dissimilar pictures. Release of radioactive rare gases, aerosols, tritium and carbon-14 seems unlikely to have a significant influence on forest damage. Influence of radioactive fallout, ozone formation by high-voltage transmission lines and synergistic effects is also found to be negligible.

Science.gov (United States)

Polymethlylmethacrylate (PMMA) is the most frequently used cement for percutaneous vertebroplasty and kyphoplasty. To aid visualisation during surgery cements are doped with radiopacifying agents such as Barium sulphate (Ba(2)SO(4)) or Zirconium Dioxide (ZiO(2)). Mounting research suggests that these agents may impair the biocompatibility of the cements. However, incorporating an alternative radiopacifier agent with excellent biocompatibility would be a significant step forward. Bioactive radiopaque glasses incorporating elements such as strontium (Sr) and zinc (Zn), known to have beneficial and therapeutic effects on bone, are of great interest in this respect. In this study, the Ba(2)SO(4) of the commercially available Spineplex was incrementally replaced with a radiopaque therapeutic glass composition. The resulting effects on cement setting time, peak isotherm, ultimate compressive strength, Young's modulus (up to 30 ...

International Nuclear Information System (INIS)

Alloying elements such as Fe and Cr are generally considered to be effective even in small quantities for corrosion resistance of Zircaloy-4. The maximum total solubility of Fe + Cr in a Zr-Sn matrix has been reported to be very low. Therefore, most of these elements are observed in the form of ternary Zr-Fe-Cr-type precipitates. To clarify the effects of precipitates on corrosion property, Zr-1.3 Sn-(Fe,Cr) alloys containing Fe + Cr from 45 up to 180 ppm (the Fe to Cr ratio is about 2) were melted from pure zirconium (X-bar Zr and EB-Zr) and pure alloying elements. They were subjected to corrosion testing in 633 K water and microstructural analysis. It was found that precipitate-free materials showed much larger weight gains than precipitate-containing materials even at the same alloy compositions. Subsequently, a corrosion test on the precipitate-free material galvanically coupled with a noble intermetallic compound of ...

International Nuclear Information System (INIS)

Results of hot cracking on welds with compositions between alloy 800 and AWS ER NiCr 3. Investigation of the influence of Si, Mn, Ti and Al on the hot cracking suscpetibility of the alloy 800. (orig.).

UK PubMed Central (United Kingdom)

BackgroundSupport groups have proved to be effective in reducing the burden on family caregivers of dementia patients. Nevertheless, little is known about the factors that influence...Full Text Available

UK PubMed Central (United Kingdom)

OBJECTIVE: The aim was to assess the psychosocial effects on the quality of life (QOL) of adults with head and neck cancer (HNC) and any gender variations with predictive factors that may influence...Full Text Available

UK PubMed Central (United Kingdom)

The effectiveness of chemotherapy in human schistosomiasis varies from one area to another, and limited data from experimentally infected animals suggest inherent differences in the susceptibility...Full Text Available

Science.gov (United States)

The catalytic effects of copper-aluminium-magnesium oxides in the oxidative coupling of phenylethyne is described. The importance of surface properties as a redox site are discussed.

UK PubMed Central (United Kingdom)

A commercial blend of essential oil (EO) compounds was added to a grass, maize silage, and concentrate diet fed to dairy cattle in order to determine their influence on protein metabolism by ruminal...Full Text Available

UK PubMed Central (United Kingdom)

1 The influence of the nonsteroidal anti-inflammatory drug naproxen on glucose metabolism and on tolbutamide pharmacokinetics and pharmacodynamics has been studied in ten maturity-onset diabetics. 2...Full Text Available

International Nuclear Information System (INIS)

The sensitivity analysis summarized in this paper was made to determine the parameters of greatest influence in the prediction of radon barrier cover thickness for the stabilization of uranium mill tailings piles. Such information provides the basis for setting priorities and levels of effort for data collection, and improves knowledge of the sources of uncertainty in the calculation of cover thickness. In the context of this paper, the influence of a parameter on cover thickness incorporates two effects: (1) the sensitivity of the mathematical formulation to changes in a parameter's value, and (2) the range of values that a parameter may take on under site-specific conditions. Of the several parameters that are used in the calculations, the most influential are cover moisture content, cover radon diffusion coefficient, tailings radium concentration and tailings radon emanating fraction, in order of decreasing relative ...

British Library Electronic Table of Contents (United Kingdom)

The coal-derived gas from a coal gasifier contains multiple contaminants, and their synergistic effects may not be simply the additive influences of individual contaminants. The present work presents the results of a study of the synergistic effects of four contaminants of major concern-S, As, P, and Cl, at the ppm level and in combinations of two, three, or four kinds-on the performance of Ni-YSZ/YSZ/LSM solid oxide fuel cells. The results indicate that both cell performance and morphology differ significantly in cells exposed to a single contaminant, and that cell performance is not simply the additive influence of each contaminant. Synergistic effects can be very destructive (accelerated degradation or even cell failure) when S is in the presence with As/P, but can also be beneficial (s...

Energy Technology Data Exchange (ETDEWEB)

The performance of the gaseous fuel supply and its influence on hydrocarbon (HC) emissions of dual-fuel engines have been investigated. A new design of manifold respirators with mixers is also presented in the paper. The design of the gaseous fuel supply system has a great influence on HC emissions in the dual-fuel engine at light load. The problem of scavenging is discussed and solved by using the manifold respirators in the dual-fuel engine. It performs the function of retarding the gaseous fuel entry timing from the moment of intake valve opening, and its delaying effects have been measured and tested. Experimental results show that the manifold respirator gives the best performance in reducing HC emissions compared with a common pipe mixer and a respirator with bo miser. In addition, the mixing effects are sensitive to the mixer configuration. (Author)

Energy Technology Data Exchange (ETDEWEB)

Three kinds of surface modifications were carried out on LiNi{sub 1/2}Mn{sub 3/2}O{sub 4} thin-films to improve the charge and discharge characteristics of LiNi{sub 1/2}Mn{sub 3/2}O{sub 4} positive electrodes. Among them, Zr(OBu){sub 4}/poly(methyl methacrylate) (PMMA)-treated LiNi{sub 1/2}Mn{sub 3/2}O{sub 4} thin-film electrodes showed charge and discharge efficiency of 80-84% in the first cycle, which was much higher than that for an untreated LiNi{sub 1/2}Mn{sub 3/2}O{sub 4} thin-film electrode (73%). The values of the charge and discharge efficiency were still higher than that for an untreated electrode after the 30th cycle. The charge and discharge curves gave two plateaus at around 4.72 and 4.76 V, which were very similar to those for the untreated electrode. Ac impedance spectroscopy revealed that the surface film resistance should not increase by Zr(OBu){sub 4}/PMMA treatment. XPS measurements suggest that a composite layer should be formed on a LiNi{sub 1/2}Mn{sub 3/2}O{sub 4} ...

International Nuclear Information System (INIS)

Effect of single and chronic irradiation on factors of hamsters natural immunity such as complement, lysozyme and antibodies in norm and in the cestode invasion has been investigated. Significant phase changes in the complement activity level, lysozyme content and specific antibodies tite have been shown to occur in hamster blood under the influence of ionizing radiation. Cestode invasion in irradiated host organism increases the negative effect of ionizing radiation on the hamster immyne system.

International Nuclear Information System (INIS)

Alloys of zirconium are widely used in various core components of power reactors. Nuclear assemblies require high degree of reliability and integrity for performing in radiation and corrosive atmosphere. The hostile environments of reactor core and inaccessibility for repairs make it mandatory to select only those joining techniques which produce not only superior quality but are also amenable to NDT methods and such other techniques which ensure acceptable performance. The author has worked on various types of welding of zirconium alloys for different applications. Modern techniques in electron beam (EB) welding, resistance welding, GTAW welding and laser welding have been developed for joining Zr alloys components for different types of reactors. Many of these have been standardized and successfully used in production. Several advancements have been made in the welding technologies towards achieving high productivity and increased reliability ...

International Nuclear Information System (INIS)

The present invention provides a fuel cladding tube having an excellent corrosion resistance and thus a long life, and a suitable manufacturing method therefor. Namely, in the fuel cladding tube, the outer circumference of an inner layer made of a zirconium base alloy is coated with an outer layer made of a metal more corrosion resistant than the zirconium base alloy. Ti or a titanium alloy is suitable for the corrosion resistant metal. In addition, the outer layer can be coated by a method such as vapor deposition or plating, not limited to joining of the inner layer material and the outer layer material. Specifically, a composite material having an inner layer made of a zirconium alloy coated by the outer material made of a titanium alloy is applied with hot fabrication at a temperature within a range of from 500 to 850degC and at a fabrication rate of not less than 5%. The fabrication method includes any of extrusion, ...

Energy Technology Data Exchange (ETDEWEB)

Substantial roles of precipitates such as Zr-Fe-Cr type intermetallic compounds on uniform corrosion and hydrogen pickup of zirconium alloys in pure water autoclave tests were investigated from an electrochemical point of view. In the previous paper, corrosion mechanism was elucidated by the anodic protection-precipitates degradation model. This paper describes the roles on hydrogen pickup. 633 K pure water autoclave test was performed on high purity zirconium, Zr-0.2Fe, Zr-0.2Cr, and Zr-0.1Fe-0.1Cr alloys. Hydrogen analysis after the corrosion test showed that hydrogen pickup ratio of Zr-0.2Fe alloy was about 80%. It was much higher than about 30% of pure Zr and about 10% of both Zr-0.2Cr and Zr-0.1Fe-0.1Cr alloys. Larger hydrogen content was introduced into Zr-0.2Fe alloy than the other ones by the cathodic hydrogen charging under coulombic equivalence. The precipitates at metal-oxide interface could act not only as cathodic sites in the ...

Energy Technology Data Exchange (ETDEWEB)

The photoelectric absorption index, I/sub Pe/, is accepted as an accurate measurement for the description of formation lithology. The measured I/sub Pe/ has been shown to deviate slightly for a given lithology because of the effects of porosity. Properly calibrated and measured I/sub Pe/'s, however, have been observed to deviate from predicted values in practice, even considering the influence of porosity. Such departures were traced to variations in borehole size and tool standoff. The nature of the physical method of recording an I/sub Pe/ does not ensure independence from the influence of the borehole environment. A series of laboratory experiments has been conducted in test formations to verify and to characterize the influence of borehole size, mudcake, and standoff on I/sub Pe/ measurement. A set of nomographs has been constructed that allows correction of I/sub Pe/ measurements for the ...

British Library Electronic Table of Contents (United Kingdom)

This study aimed to explore the impact of perceived service quality and self-concept on consumer attitude and purchase process using channel type (physical and Internet) as a segmentation variable. From the perspective of consumer behaviour, this study attempted to estimate a relational model and perform an empirical validation using female cosmetics and skincare products as an example. It was discovered that the influence of perceived service quality and self-concept on consumer attitude, purchase intention and behaviour, satisfaction, and loyalty varied with channel type. The analysis result revealed that physical stores presented higher levels of agreement with all research perspectives than Internet stores. However, only two relational paths have a higher influencing effect in physical...

British Library Electronic Table of Contents (United Kingdom)

Information technology allows national and local governments to satisfy the needs of citizens in a cost effective way. Unfortunately, citizens still tend to prefer traditional, more costly channels, such as the front desk, phone and mail. Through pilot projects government agencies attempt to influence this behavior of citizens, directing them towards the online channel. With this paper we provide insight into the possibility to influence citizens' behavior in the complex landscape of multi-channel service provision. The paper systematically compares five pilot projects using a framework that is based on organizational and marketing literature. The results show that socio-psychological factors are crucial in multi-channel management, much more than the technology itself. We conclude that ci...

International Nuclear Information System (INIS)

There are reported the results of corrosion resistance investigation of aluminium bronzes, containing about 8 and 10% of aluminium and modifying quantities of zirconium. The tests of corrosion resistance were carried out in synthetic seawater, in 3% NaCl aqueous solution and in 10% H_2SO_4 aqueous solution, with reference to industrial bronze BA93 (CuAl9Fe3). The bronzes were tested in an annealed, hardened, tempered state and after plastic hot working. The conclusion is that corrosion resistance of aluminium bronzes, especially against selective corrosion, depends more on material structure, resulted form heat treatment, than on chemical composition. (author). 6 refs, 8 figs, 6 tabs.

Energy Technology Data Exchange (ETDEWEB)

The aims of the present work were to investigate possible compatibility between sodium zirconium phosphate (NZP) and Synroc titanate phases, to prepare NZP-based waste forms by hot-pressing rather than sintering, and to investigate the incorporation in NZP of (a) Cs/Sr as simulated heat-generating nuclides; (b) simulated actinides; and (c) simulated Purex waste. The NZP samples were prepared by methods similar to those used for Synroc. The precursor NZP phase was formed from tetrabutyl zirconate Zr(OC{sub 4}H{sub 9}){sub 4}, sodium nitrate, and 85% orthophosphoric acid. Simulated waste nitrate solutions were then mixed with the liquid precursor. After stir drying of the precursor, calcination was carried out at 700{degree}C to remove nitrates and organics.

Energy Technology Data Exchange (ETDEWEB)

This work demonstrate the gasoline volatility influence, at T 10%, T 50% and T 90% distillation points, on the dynamic performance of Otto cycle engines equipped with fuel sequential electronic injection system, by using test standard procedures in dynamometer. For each distillation points three value ranges were established, giving the rise of 27 different gasoline mixtures. The effects of variation in each point on consumption, power and acceleration were verified.

British Library Electronic Table of Contents (United Kingdom)

In this work, the antibacterial effect of fluoroquinolones (FQs) upon Escherichia coli (E.coli) was measured with and without application of 40kHz ultrasound (US) stimulation. The research results demonstrated that simultaneous application of 40kHz US apparently enhanced the antibacterial effectiveness of FQs. That is, the synergistic effect was observed and the bacterial viability was reduced when FQs and US were combined. In addition, various influencing factors, such as FQs drug concentration, US irradiation time and solution temperature, on the inhibition of E.coli were also investigated. The antibacterial activity was enhanced apparently with increasing of FQs drug concentration, US irradiation time and solution temperature. Furthermore, we discussed preliminarily the mechanism of US ...

International Nuclear Information System (INIS)

The published literature is reviewed and supplemented by current information from the author's laboratory, to show the influence of various compositional, heat treatment and thermomechanical factors on the structural characteristics of Alloy 800. The features discussed include carbon, aluminium, titanium and boron, solution treatment, ageing treatments with and without applied strain, and cold working. Examples of the aspects reviewed include the effect of heat treatment and service or testing temperature on the austenite grain size, and the relative importance of M_2_3C_6 and TiC, the influence of carbon level on gamma prime, the effect of residual or steady stress combined with time at temperature on changes in carbide or gamma prime morphology, and on the appearance of sigma or other intermetallic phases. The questions posed by these features are discussed generally, in terms of their ...

International Nuclear Information System (INIS)

Mutual influence of phosphorus and carbon on the tendency to integranular corrosion (IGC) of tempered austenitic stainless steels in boiling solutions of 65% HNO_3 and 27% of HNO_3+40 g/l Cr"6"+ was investigated. It is ascertained that under the action of carbon additions susceptibility of phosphorus-containing steels to IGC increases considerably in pure nitric acid and decreases in nitric acid containing the oxidant. Possible reasons for the effects observed are discussed.

Science.gov (United States)

The synthesis of experimental data concerning the effect of jet stagnation conditions on the drag of various afterbodies is presented. Jet pressure ratio effect on boattail pressure and on boundary layer separation is analyzed. This study is made for several values of the boundary layer thickness, taking into account the fact that some test rigs make its control possible by means of tangential blowing.

Science.gov (United States)

The defect-induced electron lifetime and energy-gap anisotropy effects on the T/sub c/ of the A-15 compounds are examined. A self-consistent model calculation demonstrates that the various defect dependences of T/sub c/ can be qualitatively understood in terms of the electron-lifetime effect.

Energy Technology Data Exchange (ETDEWEB)

Chemical influences on the relative Ksub(..beta..)/Ksub(..cap alpha..) x-ray intensity ratio up to five per cent were found for different chemical constitutions of Cr, Mn, Fe and Cu by very precise PIXE measurements. In the discussion of these effects, screening of 3p electrons by a varying 3d valence charge, as well as polarizational effects are of importance.

Science.gov (United States)

The TTT diagrams describing the beta to alpha isothermal transformation have been made by isothermal dilatometry for pure uranium and 21 alloys based on chromium, silicon, molybdenum, iron, aluminium, zirconium. The thermal cycle preceeding the isothermal...

Science.gov (United States)

A large double-focusing mass spectrometer was used to obtain new values for the masses of Sr/sup 86/, Sr/sup 88/, and Zr/sup 90/. Mass differences calculated from these values are found to be in better agreement with nuclear transmutation information than were previous mass spectroscopically derived values. (auth)

Science.gov (United States)

The production of water from a subterranean formation is reduced by contacting the formation with a water dispersible hydrophilic organic polymer having a molecular weight greater than 100,000 and containing carboxyl functionality and a crosslinking composition comprising water, a zirconium compound having a value of 4+, an alpha-hydroxy acid and an amine compound.

Energy Technology Data Exchange (ETDEWEB)

The evaluated data testing for Si, Zr, Nb and Fe materials has been performed through the analyses of the neutron leakage spectrum from spherical assemblies measured in integral benchmark experiments with (d,t) and Cf fission neutron sources. Intercomparisons of the calculated from BROND-2, ENDF/B-6 and JENDL-3 data files with experimental results are presented.

Energy Technology Data Exchange (ETDEWEB)

An austenitic alloy having good thermal stability and resistance to sodium corrosion at 700.degree. C. consists essentially of 35-45% nickel 7.5-14% chromium 0.8-3.2% molybdenum 0.3-1.0% silicon 0.2-1.0% manganese 0-0.1% zirconium 2.0-3.5% titanium 1.0-2.0% aluminum 0.02-0.1% carbon 0-0.01% boron and the balance iron.

Science.gov (United States)

Ocean thermal energy conversion (OTEC) plants discharge large volumes of cold water into the upper ocean. A three-dimensional, limited-area model was developed to investigate the regional influence of the far-field effluent plume created by the negatively buoyant discharge. The model was applied to discharges from a 40-MW/sub e/ OTEC plant into coastal waters characterized by various ambient ocean conditions. A typical ambient temperature structure and nutrient distribution, as well as the behavior of the effluent plume itself, were strongly modified by the discharge-induced circulation. Although temperature perturbations in the plume were small, upward entrainment of nutrients from below the thermocline was significant. The regional influence of discharges from an 80-MW/sub e/ OTEC plant, the interactions between the discharges from two adjacent 40-MW/sub e/ OTEC plants, and the effects of coastal boundary and bottom ...

Energy Technology Data Exchange (ETDEWEB)

The effects of {alpha} particle irradiation on a passive film formed on a 304 type stainless steel are studied in situ. The experimental arrangement minimizes the radiolysis effects due to the electrolyte. Under irradiation, a modification of the electronic structure of the oxide layers is revealed by photo-electrochemistry and impedance measurements. The influence of irradiation on the corrosion resistance of the passive film is investigated. Comparing the rest potential and the breakdown potential respectively under and without irradiation, a drop in the passivity range under irradiation is shown. this is interpreted as a decrease in the corrosion resistance. (author).

Energy Technology Data Exchange (ETDEWEB)

To evaluate the effect of porosity on superplasticity behavior, it is essential to use materials of similar initial grain sizes. This can be achieved by HIPing, which provides an effective way of reducing initial porosity while avoiding appreciable grain growth; various levels of porosity can be achieved for similar grain sizes. This note is concerned with the influence of porosity on superplasticity tensile deformation of a fine grained high-purity alumina doped with copper oxide and containing a grain growth inhibitor. Specimens were prepared by slip casting to net-shape and sintering; some presintered specimens were HIPed to reduce porosity. The subsequent superplasticity behavior is related to porosity in the material.

British Library Electronic Table of Contents (United Kingdom)

The laboratory environment existing outside the test situation itself can have a substantial influence on results of some behavioral tests with mice, and the extent of these influences sometimes depends on genotype. For alcohol research, the principal issue is whether genotype-related ethanol effects will themselves be altered by common variations in the lab environment or instead will be essentially the same across a wide range of lab environments. Data from 20 inbred strains were used to reduce an original battery of seven tests of alcohol intoxication to a compact battery of four tests: the balance beam and grip strength with a 1.25g/kg ethanol dose and the accelerating rotarod and open-field activation tests with 1.75g/kg. The abbreviated battery was then used to study eight inbred str...

Energy Technology Data Exchange (ETDEWEB)

The compound GdPd{sub 2}Si, which is reported to order antiferromagnetically at 13 K, has been investigated by heat capacity and electrical resistivity measurement in the presence of external magnetic fields. In contrast to an earlier report, the zero-field heat capacity and resistivity data indicate two magnetic transitions at 13 and 17 K. The external magnetic field substantially influences the resistivity and heat capacity of the compound around the magnetic ordering temperature. The magnetocaloric effect, which is calculated from in-field heat capacity data, is quite large around the magnetic transition temperature. The magnetoresistance is also large near the magnetic ordering temperature. The metamagnetic transition is observed for 10 kOe magnetic field both in magnetocaloric and in magnetoresistance data. The metamagnetic transition strongly influences the magnetocaloric effect and ...

British Library Electronic Table of Contents (United Kingdom)

Experiment was conducted to study the effect of gamma irradiation, growth retardants and coatings (coconut oil, mustard oil and liquid paraffin) on shelf life of winter guava fruits during storage. The results revealed that the superiority of coconut oil coating over other post harvest treatments. Physiological loss in weight (7.1%), marketable fruits retained over control (86.7%), total soluble solid (16.1%), ascorbic acid (195 mg/100 g pulp) and total sugar (10%) of fruit were positively influenced by coconut oil coating up to 12 days of storage. The treatment was found significantly effective in increasing the post harvest life of fruits for 12 days over control without adversely affecting the fruit quality. Coconut oil coating gave highest consumer acceptability while, maintaining suff...

CERN Document Server

The Influence Of Plasma Temperature On Wake Wave Generation

International Nuclear Information System (INIS)

Iron oxide as sintering aid to Ce-TZP ceramics produces a beneficial effect on the tetragonal phase stabilization. It was found that ceria powder particle size of 2,0 #mu#m turns the grain-boundary electrical conductivity higher than ceria powder of smaller grain size. (author)

Science.gov (United States)

Two-wave mixing in sillenite crystals such as bismuth silicon oxide (Bi12SiO20) and bismuth titanium oxide (Bi12TiO20) of (001)- and (221)-cuts for counterpropagating geometry was studied within the frame of slowly varying amplitude approximation. Electrooptic, photoelastic, piezoelectric, self-diffraction effects and optical activity were taken into account.

Energy Technology Data Exchange (ETDEWEB)

This book presents papers on internal combustion engines. Topics considered include the influence of partial suppression of heat rejection on performance and emissions, duothermic combustion, turbochargers made of sintered silicon nitrides, heat flux, low heat rejection engines, exhaust energy recovery, combustion chamber insulation, computerized simulation, heat transfer, friction, hoop stress effects, and bonding ceramics and metals.

Energy Technology Data Exchange (ETDEWEB)

The bibliography contains citations concerning the structural properties of sputtered tantalum and tantalum compounds. The preparation of thin film capacitors and resistors is described. The electrical properties of the sputtered films are also included. The influence of the substrate on the properties of the coatings is considered, including adherence of the coating to the substrate, and the effects of impurities on coating integrity. (Contains 250 citations and includes a subject term index and title list.)

Energy Technology Data Exchange (ETDEWEB)

The possibilities and problems of PCA in phase separation are shown on Ni, Pd, and Pt silicides. The PCA depth profiles are less influenced by sputter and matrix effects than usual Auger depth profiles. The position of the silicide-Si interface is well defined by the component distribution crossover in PCA profiles. An interface component between Pd and Pt silicides and Si substrate is determined by PCA.

Energy Technology Data Exchange (ETDEWEB)

A mathematical model of the multi machine electric power system to analyse its dynamics has been worked out. The effectivity of the power system stabilizer developed in the one machine system has been tested by means of this model. The influence of the arrangement of the stabilizers on the stability of the electric power system has also been investigated. High damping of electromechanical transient processes has been achieved. 7 refs., 1 tab., 5 figs.

Energy Technology Data Exchange (ETDEWEB)

The pharmacokinetics of Tl/sup +/ were studied in 9 patients who underwent myocardial scintigraphy with /sup 201/Tl/sup +/. The time course of the /sup 201/Tl/sup +/ concentration fitted to an open two-compartment model. Using previously published dialysance values the influence of hemodialysis on Tl/sup +/ elimination was calculated. Hemodialysis in Tl/sup +/ intoxications should be moderately effective.

Energy Technology Data Exchange (ETDEWEB)

Isospin-breaking effects in the baryonic sector are studied in the framework of a medium-modified Skyrme model. The neutron-proton mass difference in infinite, asymmetric nuclear matter is discussed. In order to describe the influence of the nuclear environment on the skyrmions, we include energy-dependent charged and neutral pion optical potentials in the s- and p-wave channels. The present approach predicts that the neutron-proton mass difference is mainly dictated by its strong part and that it strongly decreases in neutron matter. (orig.)

International Nuclear Information System (INIS)

It if first shown, that the effective field of uniaxial magnetic anisotropy of Fe-Cr-P-C and Fe-Ni-B-Si system amorphous alloys is reduced with an increase of the source melt isothermal exposure time. The behaviour noted is conditioned by microcoherence and relaxation processes in the nonequilibrium liquid phase after crystal-liquid phase transition.

Science.gov (United States)

The implementation of information technology will continue to have important effects on the practice of emergency medicine. Patient registration and tracking systems, telemedicine electronic order entry systems, and the advent of electronic health records are some examples of applications that influence patient care in emergency departments. We review the literature regarding information technology advances in emergency medicine and outline the important role that emergency physicians play in developing and implementing a national health information technology strategy. PMID:16712540

Energy Technology Data Exchange (ETDEWEB)

The purpose of the present work was to establish the flammability limits of hydrogen in air for upward vertical flame propagation at elevated temperatures up to 350 deg and atmospheric pressure in a conventional stainless steel test tube apparatus, and to investigate the extent to which a prolonged exposure (i.e., residence time) of the mixture to elevated temperatures before spark ignition may influence the value of the flammability limits. 9 refs.

International Nuclear Information System (INIS)

The influence of RTA (Rapid Thermal Anneal) treatment on MOS radiation hardness is demonstrated and compared with classical furnace treatment. In the case of the RTA, the oxide trapped charge is found to depend on: (i) the anneal temperature as expected, data are in good agreement with a recently developed model of oxygen out-diffusion; (ii) the location across the wafer with a radial dependence, results could be related to stress induced by thermal gradient.

International Nuclear Information System (INIS)

In this paper, aluminium nitride synthesis is carried out by direct laser irradiation onto an aluminium target surface in a nitrogen containing atmosphere. The influence of various processing parameters on the microstructure of AlN thin films is investigated in order to improve their tribological properties. The main microstructural characteristics: nature, concentration, in depth distribution and morphology of various phases are studied versus processing parameters by TEM and GIXD. (author). 2 refs., 1 fig., 2 photos.

International Nuclear Information System (INIS)

Radionuclide X-ray fluorescence method with a Si/Li semiconductor detector and "2"3"8Pu exciting source was used in the determination of Cr, Fe, Ni, Cu, and Zn content in industrial wastewaters. Simultaneously, the effects of the wastewaters on activated sludge biocenose were evaluated. (author) 6 refs.; 1 fig.; 1 tab.

Energy Technology Data Exchange (ETDEWEB)

Corona from bare conductors of electrical overhead power lines is studied in this article. Its origin, as well as, its bad influences over communication systems are both studied, yet. Line`s models are defined, in order to be able the examination of Corona on line`s cables. Formulas for the surface electrical gradient calculations are shown. (author) 2 refs.

Energy Technology Data Exchange (ETDEWEB)

Process solvent was hydrogenated in the brown coal liquefaction, to investigate the influence of it on the prethermal treatment and liquefaction. Consequently, it was found that the n-hexane soluble (HS) yield was improved. In this study, capacity of hydrogen transfer from solvent during prethermal treatment and effects of catalyst were investigated. Since prethermal treatment in oil was effective for improving the oil yield in the presence of hydrogen/catalyst or high hydrogen-donor solvent, influence of hydrogen-donor performance of solvent or addition of catalyst on the hydrogenation behavior of coal and the characteristics of products during prethermal treatment were investigated in relation to successive liquefaction results. As a result, it was found that the increase of HS yield was due to the acceleration of conversion of THF-insoluble using high hydrogen-donor solvent and/or by adding catalyst. ...

International Nuclear Information System (INIS)

Effects of ethanol in vitro on membrane vesicles were evaluated by monitoring "3"6Cl"- influx. Different assay parameters were tested to determine increased or decreased action of ethanol on GABA-activated chloride channels. The ability of 30 mM ethanol to augment "3"6Cl"- flux was seen at 0 degree C, in the absence of GABA, and at 34 degree C in the presence of GABA, using two different assay procedures. Picrotoxin blocked the direct effects of ethanol suggesting GABA_a involvement. Endogenous GABA in the medium surrounding the microsacs was assayed at different temperatures both in the presence and absence of GABA and ethanol. The direct effect of ethanol did not appear to involve the action of endogenous GABA. In addition to temperature effects on the assay, time of membrane storage also influenced ethanol action. Microsacs stored on ice for 2 hours or more lost their ability to ...

CERN Document Server

Focusing and resonance properties of two-dimensional small-size hemielliptic lenses made of different materials are studied numerically in order to estimate the influence of internal reflections on the radiation characteristics of dielectric lens antennas. Accuracy of in-house made algorithms based on combination of geometrical and physical optics and FDTD in the analysis of optical and modal effects in the behavior of such lenses is tested by comparison with the exact solution obtained using the Muller boundary integral equations. The range of applicability for the approaches is discussed.

Energy Technology Data Exchange (ETDEWEB)

A special study was conducted to investigate the influences of minimum approach temperature differences occurring in supercritical-heater/vaporizer and evaporative-condenser heat rejection systems on geothermal-electric binary power plant performance and cost of electricity. For the systems investigated optimum pinch points for minimizing cost of electricity were estimated to range from 5 to 7/sup 0/F for the heater vaporizer. The minimum approach of condensing temperature to wet-bulb temperature for evaporative condensers was estimated to be about 30/sup 0/F in order to achieve the lowest cost of electricity.

British Library Electronic Table of Contents (United Kingdom)

This paper is devoted to investigate the influences of thermal dispersion and magnetic field on a hot semi-infinite vertical porous plate embedded in a saturated Darcy-Forchheimer-Brinkman porous medium. The coefficient of thermal diffusivity has been assumed to be the sum of the molecular diffusivity and the dynamic diffusivity due to mechanical dispersion. The effects of transverse magnetic field parameter (Hartmann number Ha), Reynolds number Re (different velocities), Prandtl number Pr (different types of fluids) and dispersion parameter on the wall shear stress and the heat transfer rate are discussed.

Energy Technology Data Exchange (ETDEWEB)

Various chemical, physical, and mechanical methods to prevent unwanted deposition of mineral scale are described. The suitability of the different methods, which largely depends on the specific features and requirements of the system involved, is discussed. Special emphasis is placed upon the threshold treatment, where the growth process is retarded by the addition of trace amounts of growth inhibitors. Growth experiments have been performed on barium sulfate and calcium sulfate dihydrate seed crystals, suspended in a supersaturated solution with and without organic bisphosphonates as inhibitors. Two methods are selected for the analysis of the growth data. A degree of inhibition is defined to obtain a quantitative description of the influence of a growth inhibitor on the growth rate of the crystals. In addition the influence of the molecular structure of various bisphosphonates with different substituents is shown. The ...

Science.gov (United States)

Pinealectomy completely prevented gonadal regression as well as reduction in body weight and white adipose tissue content of the gonadal and retroperitoneal fat deposits in male meadow voles transferred from long to short day lengths. Pineal influences on pelage characteristics depended on which parameter was assessed. For instance, the increase in guard hair length observed in short-day control voles was blocked by pinealectomy; however, a similar increase in underhair length was unaffected by removal of the pineal gland. Photoperiod-dependent changes in fat deposition, testicular activity, and guard hair length presumably rely on altered pineal secretory activity to transduce the effects of day length on the neuroendocrine axis; however, mechanisms independent of pineal activity may be capable of mediating photoperiodic control of underhair growth. PMID:2979644

CERN Document Server

In the paper we investigate a mathematical model describing the growth of tumor in the presence of immune response of a host organism. The dynamics of tumour and immune cells is based on the generic Michaelis-Menten kinetics describing interaction and competition between the tumour and the immune system. The appropriate phenomenological equation modeling cell-mediated immune surveillance against cancer is of the predator-prey form and within a given choice of parameters exhibits bistability. Under the influence of spontaneous weak fluctuations, the model may be analyzed in terms of a stochastic differential equation bearing the form of an overdamped Langevin-like dynamics in the external quasi-potential represented by a double well. We analyze properties of the system within the range of parameters for which the potential wells are of the same depth and when the additional perturbation describing a periodic treatment is insufficient to overcome the barrier height ...

British Library Electronic Table of Contents (United Kingdom)

Non-isothermal TG/DTG measurements are widely used to determine kinetic parameters of oxidation and gasification of carbons, e.g. by multi-heating rate methods. Thereby it is important to avoid spurious effects due to diffusion limitations. In this work, TG/DTG experiments with activated carbon were conducted under isothermal and non-isothermal conditions. The agreement of the experimental results with results of simulations based on the intrinsic kinetics, pore diffusion and external diffusion in/to the sample (crucible) is very good. The simulations show that mass transfer has an unwanted influence on TG measurements, if the concentration of the gaseous reactant (O2 and CO2) is too low and/or the heating rate is too high. Based on literature data, the simulation was extended to blast fur...

Energy Technology Data Exchange (ETDEWEB)

The microstructure of the interphase in semicrystalline polymer matrix composites has a dramatic influence on their mechanical properties. Studies have been performed to alter this region and to correlate various interphase morphologies with changes in fiber-matrix adhesion. A reinforced nylon 66 composite, when subjected to specific thermal histories, contains an interphase composed of transcrystallinity. This region has been altered by coating fibers with a diluent, poly(vinyl pyrrolidone), and/or adding the diluent to the matrix material in very small quantities. Interphase morphology was investigated with optical microscopy, and adhesion was measured using a modified fiber pull-out test. It was found that transcrystallinity increases the interfacial shear strength. The effect different interphase morphologies have on the durability of bulk composite samples is currently under investigation.

British Library Electronic Table of Contents (United Kingdom)

Many hoarding rodents use burrows not only for dwelling and protection from natural enemies, but also for food storage. However, little is known how burrows used by scatter-hoarding animals influence their foraging behaviors. In addition, handling time for a given food item has a fundamental impact on hoarding strategies of these hoarding animals: food items with longer handling time are more likely to be hoarded due to increasing predation risk because the animals spend more time outside their burrows if they consumed such food. By providing with two types of artificial burrows (aboveground vs. underground) and two types of food items (i.e. seeds) with contrasting handling times, we investigated how burrow condition and handling time co-influence hoarding strategies of a key scatter-hoard...

International Nuclear Information System (INIS)

We have constructed a mathematical model that describes the coherent spontaneous radiation of a macroscopically filled exciton mode. We have demonstrated qualitatively ways in which a coherent subsystem of excitons can be formed. When this occurs under the influence of an external coherent source, exciton free induction occurs, while in the case of a spontaneous transition of the excitons to a coherent state through freezing of the reservoir of intermolecular interactions superradiance occurs. We have concluded that superradiance in the system of Frenkel excitons is possible under the influence of the non-Dicke mechanisms of self-induction of correlations, when the dipole transition moments of the individual atoms are coupled into a single macroscopic effective spin through their electrostatic interaction, this being analogous to the ordering of magnetic dipole moments in a ferromagnet.

British Library Electronic Table of Contents (United Kingdom)

The influence of chemical and solvent extraction compatibilising techniques on the mechanical properties of poly-lactic acid (PLA) and MaterBi-polyester (PEM) based bio-composites are compared. First, fibres were chemically grafted with two fatty chains: stearic anhydride and octadecylisocyanate. Grafted fibres were characterised by FTIR and elemental analyses. Contact angle measurements show the hydrophobisation of the fibres in spite of very low surface grafting. Extracted and non-grafted fibres were prepared to be used as references. PEM and PLA-based composites with 30% w/w were prepared by compression moulding. Their mechanical properties were studied. It was found that chemical and solvent treatment of the fibres improved the reinforcement effect in the case of a PEM matrix and the Y...

Energy Technology Data Exchange (ETDEWEB)

The main goal of this research is to delineate the wetting behavior of coal and it subsequent effects on fine coal processing. As both bulk and surface properties of coal are interrelated and have a controlling role on the performance of these processes, a detailed study has been undertaken to correlate their influence on both wetting behavior and the response of coal to flotation and other unit operations encountered in fine coal processing. During the last quarter, the effect of coal rank on water retention capacity was investigated. The effect of pH on the vacuum flotation yield and the effect of desliming on the film flotation response of coal were also studied. 6 refs., 5 figs.

British Library Electronic Table of Contents (United Kingdom)

There is increasing evidence that adolescence, like early life, is a sensitive period in which ongoing brain development can be influenced by environmental factors. This review describes our use of social instability as a model of mild adolescent social stress, its effects on social interactions and on hypothalamic?pituitary?adrenal function over the course of the procedure and in response to new stressors. The effects of social instability are sex-specific, with qualitative differences between the sexes on HPA function over the course of the stressor procedure, and with greater effects in males on behaviour observed during the social instability and greater effects in females on behavioural responses to drugs of abuse into adulthood, long after the stress exposure. The results from invest...

Energy Technology Data Exchange (ETDEWEB)

Theoretical assessment on the chromatographic {sup 99m}Tc generator preparation using (n, {gamma}) {sup 99}Mo produced ex-natural molybdenum was carried out. The relationship between the neutron flux for MoO{sub 3} target activation, Mo-content or Mo adsorption capacity of column packing material, {sup 99m}Tc pertechnetate concentration and/or {sup 99m}Tc radioactivity of eluate was established. The reasonably lower limit of neutron flux of reactor and Molybdenum content of column packing material were found out to estimate the production of portable chromatographic generators available for nuclear medicine application. The concentration of {sup 99m}Tc pertechnetate eluate of low {sup 99m}Tc concentration using the column elution technique was also evaluate theoretically and conducted successfully in practice. Three options of {sup 99m}Tc generator using Titanium-Molybdate, Zirconium-Molybdate and Zirconium Oxide as generator column-packing ...

Energy Technology Data Exchange (ETDEWEB)

A theoretical model, which describes subband gap photoexcitation involving localized electronic states, was developed. The escape probability of a charge carrier trapped in a localized state is considered via Poole-Frenkel, direct tunneling, or phonon-assisted tunneling processes, as competing escape mechanisms. Photoelectrochemical experiments were performed on the passive films formed on zirconium and amorphous iron-zirconium alloys and on pure HfO/sub 2/ films and HfO/sub 2/ films implanted with varying concentrations of xenon. These films were found to possess some degree of disorder depending on the substrate, the thickness of the film, and the extent of implantation. The spectral dependence of the photocurrent in all of the films studied is considerably different from what was found for crystalline passive films. The potential dependence of the photocurrent yields Poole-Frenkel behavior. Reverse tunneling processes were also observed at ...

International Nuclear Information System (INIS)

Reaction of formation of 3, 5, 7, 3', 4', 5' - hexaoxiflavone - myricetin complexes with zirconium and hafnium ions has been the basis for development of luminescent method of determining these elements. Optimum conditions for complexing have been determined. For Hf they are : 8-9 HCl concentration, maximum fluorescence wave length (lambda fl.)of 520 nm, wave length of exciting light (lambda el) of 436 nm, for Zr lambda fl = 536nm, lambda el = 436 nm. Stable fluorescence establishes after 25 min. for Zr and after 15 min for Hf in the presence of 40% ethanol. Usage of various camouflage agents has permitted to attain high selectivity of the method. Possibility for determination of Zr with myricetin in the presence of a 10-time excess of Hf, Cr, Cu, 50-time excess of Mo and Ti is shown. Sensitivity of Zr determination is 2.0x10 #mu#g"-"2/ml, for Hf it is 9.0x10 #mu#g"-"3 and mineral waters.

International Nuclear Information System (INIS)

Metastable austenitic steels show excellent mechanical properties, such as high strength combined with excellent ductility and toughness due to martensitic transformation under mechanical loading (transformation induced plasticity effect). A good energy consumption, and, in the case of high-alloyed metastable austenitic steels, a high corrosion resistance, increase the potential of these materials for diverse applications, also in regard of safety requirements. Up to now, numerous wrought alloys were investigated concerning mechanical behaviour, TRIP-effect, martensitic transformation behaviour and modelling of transformation kinetics or stress-strain behaviour. New high alloyed cast CrMnNi-steels, developed at Technical University Bergakademie Freiberg, provide the chance to reduce processing steps, production time and costs. In order to understand the influence of temperature on the martensitic phase transformation ...

International Nuclear Information System (INIS)

Studies were undertaken to examine the effects of animal age on the anticarcinogenic properties of antioxidants. Female hairless mice, 2.5, 4.5 and 9.5 months of age, were subjected to daily irradiation from Westinghouse BZS-WLG lamps for 19 weeks. Experimental groups of animals were maintained on a commercial rodent meal supplemented with a 2% (w/w) antioxidant mixture. Control groups received only the meal. Tumour latency, expressed as median time to tumor development, was significantly greater for all age groups receiving antioxidants than for their similarly aged controls. However, the response to antioxidants appeared to decrease with age and the antioxidant effect was significantly less in the 9.5 month-old group than in the 2.5 month-old group. Likewise, the two youngest groups receiving antioxidants demonstrated a significantly fewer number of tumors per animal. It is concluded that animal age influences the degree ...

Energy Technology Data Exchange (ETDEWEB)

For the removal and recycle of CO2, a global warming gas, utilization of photosynthesis by micro algae is investigated. Formed micro algae are decomposed into CO2, H2O and CH4 again, which does not result in the permanent fixation. For the effective utilization of these micro algae, creation of petroleum alternate energy was tried through the co-liquefaction of micro algae with coal. Were investigated influences of the reaction temperature during the co-liquefaction and influences of catalysts, such as Fe(CO)5-S, Ru(CO)12, and Mo(CO)6-S, which are effective for the coal liquefaction. Micro algae, such as chlorella, spirulina, and littorale, and Yallourn brown coal were tested. It was found that co-liquefaction of micro algae with coal can be successfully proceeded under the same conditions as the liquefaction of coal. The oil yield obtained from the co-liquefaction in the presence of Fe(CO)5-S, an ...

International Nuclear Information System (INIS)

The method of programmed thermodesorption has been used to study the forms of hydrogen adsorption in ZrNiHsub(x) hydride. It is shown that high concentration of the hydrogen, which extracted from hydride in the temperature range of 240-260 deg C results in appearance of ''reverse'' peak. Charge of hydride adsorption properties during its oxidation-reduction treatment is studied. Comparison with spectra of hydrogen thermodesorption from the surface of Ni/ZrO_2 deposited catalyst and zirconium oxide is carried out.

Energy Technology Data Exchange (ETDEWEB)

The theoretical principles underlying the formation of oxide and, in particular, anodic oxide coatings on metals produced by chemical oxidation, anodizing in solutions, and anodizing in cold plasmas are reviewed. The mechanisms and conditions of anodic oxidation are described, and the structure of anodic oxide coatings on aluminum, magnesium, beryllium, zinc, cadmium, iron, cobalt, nickel, titanium, zirconium, tantalum, and chromium alloys is examined. Attention is also given to various applictins of anodized coatings. 54 references.

International Nuclear Information System (INIS)

In one of the first uses of high Tc superconductors in an end-use product, Lake Shore Cryotronics and a Swiss lab have developed a liquid nitrogen level sensor using a high Tc thin film. The probe is manufactured using a seamless stainless steel tube with an yttrium-based zirconium oxide flame-sprayed on the tube. A plasma-sprayed superconductor compound is deposited on top of that. The probe is coated with a sealant that protects the superconducting film from the atmosphere. This manufacturing method has yielded an extremely durable product. Unaffected by ice formation and related mechanical problems, the superconducting level sensor can be kept in the dewar for long periods of time.

International Nuclear Information System (INIS)

In association with periodic inspection of CANDU nuclear power plant components, Canadian Standards Association issued CSA N285.8 in 2005 as technical requirements for in-service evaluation of zirconium alloy pressure tubes in CANDU reactors. This first version, CSA N285.8 involves procedures for, firstly, the evaluation of pressure tube flaws, secondly, the evaluation of pressure tube to calandria tube contact and, thirdly, the assessment of a reactor core, and material properties and derived quantities. The evaluation of pressure tube flaws includes delayed hydride cracking evaluation the procedures of which are stipulated based on the existing delayed hydride cracking models. For example, the evaluation of flaw-tip hydride precipitation during reactor cooldown involves a procedure to calculate the equilibrium hydrogen equivalent concentration in solution at the flaw tip, Htipas follows: Htip=Hfexp[- (VH delta no.)/RT], where Hf is the total bulk hydrogen ...

British Library Electronic Table of Contents (United Kingdom)

Background Previous reports in adults have suggested that the effects experienced after cannabis use can be described in terms of positive and negative subtypes that are heritable and are associated with abuse and dependence. This study extends existing research by inclusion of adolescents and young adults in an offspring of twins design which makes it possible to take into account genetic and environmental risks for substance use disorder. Methods Data were collected from 725 twin members of the Vietnam Era Twin Registry, 839 of their 12-32 year old biological offspring and 427 mothers. Offspring who had ever used cannabis (n=464) were asked the degree to which they typically experienced 13 subjective effects shortly after using cannabis. Latent class analysis (LCA) was used to derive sub...

Energy Technology Data Exchange (ETDEWEB)

The influence of a periodic electromagnetic field on the radiative corrections to the atomic energy levels is studied for the case of ''strong fields'' for which the interaction between the atom and field is of the order or greater than the radiative effects. The analysis is carried out on the basis of the Schwinger-Dirac equation for the propagation function of a bound electron in the field and on the basis of the density matrix in the Furry representation. It is shown that in the strong field approximation the radiative shifts and widths are manifest as radiative corrections to the quasi-energies. In super-high resolution experiments intensity effects in the radiative corrections to the atomic levels are obtained in the case of single-photon resonance. Some multiphoton processes are condidered by taking into account the effect of the field on the radiative structure ...

British Library Electronic Table of Contents (United Kingdom)

Nucleotides released upon brain injury signal to astrocytes and microglia playing an important role in astrogliosis, but the participation of microglia in the purinergic modulation of astrogliosis is still unclear. Highly enriched astroglial cultures and co-cultures of astrocytes and microglia were used to investigate the influence of microglia in the modulation of astroglial proliferation mediated by nucleotides. In highly enriched astroglial cultures, adenosine-5?-triphosphate (ATP), adenosine 5?-O-(3-thio)-triphosphate (ATP?S), adenosine 5?-O-(3-thio)-diphosphate (ADP?S; 0.01?1?mM), and adenosine-5?-diphosphate (ADP; 0.1?1?mM) increased proliferation up to 382%, an effect abolished in co-cultures containing 8% of microglia. The loss of ATP proliferative effect in co-cultures is supporte...

Energy Technology Data Exchange (ETDEWEB)

Haemocyanin serves as normal transporter of oxygen in many Arthropods. The oxygen equilibrium curves have been described for the haemocyanins of many Arthropods and Molluscs. Oxygen equilibrium curves of the blood reveal the relationship between the oxygen tension and the percentage saturation of the haemocyanin. The shape of the oxygen equilibrium curves vary in position from sigmoid to hyperbolic in different animals or even undulatory as shown in some chitons. Oxygen equilibrium curves are known to be influenced by pH, temperature and inorganic ions. The effect of environmental pollutants like the heavy metals on the oxygen equilibrium curves of the fresh water crab has not been previously reported. One of the toxic heavy metals with regard to aquatic organisms is lead. Hence the present study was designed to determine the effect of organic and inorganic lead on the oxygen equilibrium curve of the fresh water crab, ...

International Nuclear Information System (INIS)

The potential material class for use at 600"0C and more, e.g. for steam turbines with improved thermal efficiency, are austenitic steels. Using these steels with welded joints, it is to be considered that, by superposition of weld residual stresses and service stresses, extensive creep strains - and in the worst case crack formation - can occur locally. To assess the influence of these effects on service behaviour, different material states of CrNi-steels and Incoloy 800 were investigated with respect to strength, ductility and, especially, to crack and creep crack growth in the temperature range around 600"0C. It is shown that creep embrittlement, not microstructural changes as effected by weld heat input, causes heat affected zone (HAZ)-reheat cracking. Creep embrittlement can be avoided by special design and fabrication rules. (orig.).

British Library Electronic Table of Contents (United Kingdom)

ABSTRACT This research examined whether the Internet improves life satisfaction. The study surveyed 195 college students, and a structural model was built to explain effects of the Internet on school life satisfaction using a confirmatory factor analysis (CFA). In line with social cognitive theory and literature on social effects of the Internet, current data supported the hypotheses that Internet use, perceived online social support, and online social self-efficacy had direct positive impacts on school life satisfaction. Offline extroversion, online extroversion, online social self-efficacy, and online social outcome expectations influenced school life satisfaction indirectly: offline extroversion acted through social online self-efficacy and online extroversion; online social self-effica...

Science.gov (United States)

This paper focuses on a factorial-based design strategy. The approach provides an efficient and statistically reliable means for assessing the influence of multivariable effects. It is applied to the detection and evaluation of damage in impacted composite sandwich panels. The experimental results obtained from this test strategy are utilized to form an empirical response function. The resulting polynomial relates damage area to residual compression strength at values of independent variables for which testing did not occur. The response function also identifies nonlinear interaction effects of key variabes that cannot be easily ascertained by traditional single-variable test strategies. Independent variables evaluated include core thickness, number of face sheet plys and impact energy. The methodology presented allows the designer to predict with more confidence the damage tolerance of a composite material component, and ...

Norwegian Open Research Archives (NORA)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication. 3 refs.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

Energy Technology Data Exchange (ETDEWEB)

The influence of high temperature thermal ageing treatments on the development of intercrystalline creep damage in two variants of Alloy 800 has been investigated. Ageing up to 3000 h and creep testing were carried out at 800 and 900 C. The high temperature behaviour of the 800HT variant is discussed with reference to the effect of heat treatments on the microstructure. The metallographic methods by which the creep damage was quantitatively determined are described. The growth rate of intercrystalline microcracks was described using a statistical model and the dependence of crack growth rate on the thermal history for both 800HT and 800H was determined. The carbide precipitation and growth processes were determined as functions of the exposure temperature and duration. The results showed the three characteristic stages, precipitation, growth and coarsening (Ostwald ripening). The largest increase in the intergranular creep damage was found in ...

International Nuclear Information System (INIS)

It is very well known that the CANDU reactor has positive Coolant Void Reactivity (CVR), which is most important criticisms about CANDU. The most recent innovations based on using a thin absorbent Hafnium shell in the central bundle element were successfully been applied to the Advanced CANDU Reactor (ACR) project. The paper's objective is to analyze elementary lattice cell effects in applying such methods to reduce the CVR. Three basic fuel designs in their corresponding geometries were chosen to be compared: the ACR-1000TM, the RU-43 (developed in INR Pitesti) and the standard CANDU fuel. The bundle geometry influence on void effect was also evaluated. The WIMS calculations proved the Hafnium absorber suitability (in the latest 'shell design') to achieve the negative CVR target with great accuracy for the ACR-1000 fuel bundle design than for the other two projects. (authors)

International Nuclear Information System (INIS)

Denting studies have been undertaken in order to assess the influence of the most important parameters which could initiate corrosion of the carbon-steel occurring in the tube-tube support plate crevices of some PWR steam generators. Tests have been carried out in model boilers, feedwater being polluted with sea or river water. Specific effect of chloride or sulfate and influence of oxygen content, magnetite addition and pH value were investigated. In magnetite prepacked crevices, denting is obtained within 1000 hours for sea-water pollution of 0.3 ppm chloride at the blowdown. In neutral chloride or in river water denting is observed only with oxygen addition. Denting prevention is effective in the case of an on-line addition of phosphate, boric acid or calcium hydroxide. For denting stopping, boric acid or calcium hydroxide is efficient even with a high sea-water pollution. Soaks cannot stop denting ...

Energy Technology Data Exchange (ETDEWEB)

A heat transfer (condenser) of a domestic freezer was tested in a vertical channel in order to study the influence of the chimney effect in the optimization of the heat transfer coefficient. The variation of the opening of the channel, position and the heating power of the heat exchanger in the heat transfer coefficient was considered. The influence of the surface emissivity on the heat transfer by thermal radiation was studied with the heat exchanger testes without paint and with black paint. The air velocity entering the channel was measured with a hot wire anemometer. In order to evaluate the chimney effect, the heat exchanger was testes in a open ambient. This situation simulates its operational conditions when installed on the freezer system. The variables collected in the experimental procedures was gathered in the form of dimensionless parameters as Nusselt, Rayleigh, Grashof and Prandtl numbers, ...

Energy Technology Data Exchange (ETDEWEB)

Measurements of the rate of heat transfer, enhanced by electroconvection, between two parallel plates have been carried out. Results show that the non-dimensional heat flux, or the Nusselt number, increases when an electric field acts on an injected space charge within the insulating liquid. The motion of the liquid depends on the electrical forces (Coulomb force) and the buoyancy effects have little or no influence. This is evident from steady state and time dependent results which show that for a given voltage, the Nusselt number takes the same value no matter what the flux of heat supplied to the bottom plate.

International Nuclear Information System (INIS)

When decontaminated with continuously replenished CAN-DECON reagent in a once-through system, carbon steel contaminated with "6"0Co during exposure to reducing coolant in stainless steel loops loses up to 90 percent of its radioactivity in the first few minutes. Afterwards, the rate of removal falls to much lower values which persist for many hours to the end of the experiment. The effects of flow rate, temperature and reagent concentration on the initial rates of decontamination indicate that mass transfer in the liquid is an important factor in the decontamination. The decontamination factor is influenced by the initial rate.

Energy Technology Data Exchange (ETDEWEB)

The pH of the solution is shown to significantly effect the reflection anisotropy spectroscopy (RAS) profiles of adenine adsorbed at Au(110)/electrolyte interfaces. At pH 12.8 the net adsorption is very weak due the formation of negative adenine ions in solution. The sensitivity of the RAS profiles to the pH of the solution is probably due to a change in the geometry of the adsorbed molecules caused by a disruption of the base stacking configuration that is adopted when adenine is adsorbed from solutions at pH 7.1. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

Isothermal transformation kinetics of austenite to acicular ferrite and allotriomorphic ferrite were measured in reheated low alloy steel weld deposits with similar weld compositions and austenite grain size but different inclusion characteristics. Accelerated kinetics of transformation to acicular ferrite were observed in weld metal containing coarser and titanium-rich inclusions. In contrast, kinetics of transformation to allotriomorphic ferrite were not influenced by inclusion characteristics, but, rather, by the austenite grain size and carbon concentration.

International Nuclear Information System (INIS)

Strain rate effects for the high strength, metastable beta-titanium alloy Ti-8Mo-8V-2Fe-3Al are assessed in terms of tensile and fracture toughness behavior. It is shown that as the strain rate increases the yield strength, ultimate tensile strength, and ductility also increase. As a result of the decrease in the amount of intergranular fracture as the strain rate is increased, the dynamic fracture toughness values K/sub Id/ are greater than those obtained under static conditions as given by K/sub Q/.

Energy Technology Data Exchange (ETDEWEB)

An algorithm is proposed which treats the ECH generated potential in a self-consistent way, by extending the Monte-Carlo Fokker-Planck method used by Murakami [S. Murakami et al., Proc. 17th IAEA Fusion Energy Conference, Yokohama, 1998 (International Atomic Energy Agency, Vienna, in press), paper CN-69/TH2/1]. The additional physics is expected to influence the transport of both thermal and suprathermal electrons in a helical toroidal system. (author)

International Nuclear Information System (INIS)

Reflection coefficients of electromagnetic waves in a nonuniform plasma layer with electrons, positive ions and negative ions, covering a metal surface are investigated by using the finite-difference-time-domain method. It is shown that the reflection coefficients are influenced greatly by the density gradient on the layer edge, layer thickness and electron proportion, i.e., the effect of the negative ions. It is also found that low reflection or high attenuation can be reached by properly choosing high electron proportion, thick plasma layer, and smooth density gradient in the low frequency regime, but sharp density gradient in the high frequency regime. (authors)

International Nuclear Information System (INIS)

Radiation-initiated polymerization of styrene and acrylic acid in poplar wood were investigated for the preparation of wood-polymer composites. The direct irradiation method was applied to the monomer adsorbed poplar wood specimens. 8000 Ci "6"0Co source at a dose rate of about 0.4 Mrad/h was used. Furthermore the effects of carbon tetrachloride, methanol, dioxane and acrylonitrile on styrene polymerization were investigated and the reaction rates were calculated for each case. The influence of CCl_4 (10%) on acrylic acid polymerization in poplar wood was also determined. (author).

International Nuclear Information System (INIS)

Impurity effects on the photon-assisted spin-polarized transport through armchair carbon nanotubes connected with ferromagnetic leads are investigated theoretically. The impurity induces one resonant state whose position depends on the impurity strength, which can break the electron-hole symmetry. Whether the impurity suppresses or enhances the spin-coherent current depends on the nanotube length. When the microwave fields are applied on the nanotube, additional small side peaks caused by the photon-assisted tunneling are found. With increasing the impurity strength, one new current peak appears under the influence of both the microwave fields and the impurity.

International Nuclear Information System (INIS)

Some results on mechanical property study of copper and titanium subjected to impact load and next to neutron irradiation are presented. It was shown that shock wave influence involves a substantial shape change of the stress-strain diagram and of respective mechanical characteristics. Yield- and ultimate strength were substantially increased, as well as hardness with a considerable drop of plasticity. Also a heat stability of copper and titanium specimens was studied after being treated with shock-waves and neutron radiation. Results are given of electron microscope study of titanium structure sfter explosion hardening, which caused decomposition of hydride segregations in titanium and increased dislocation density.

British Library Electronic Table of Contents (United Kingdom)

Abstract Ionizing radiation is a ubiquitous feature of the Cosmos, from exogenous cosmic rays (CR) to the intrinsic mineral radioactivity of a habitable world, and its influences on the emergence and persistence of life are wide-ranging and profound. Much attention has already been focused on the deleterious effects of ionizing radiation on organisms and the complex molecules of life, but ionizing radiation also performs many crucial functions in the generation of habitable planetary environments and the origins of life. This review surveys the role of CR and mineral radioactivity in star formation, generation of biogenic elements, and the synthesis of organic molecules and driving of prebiotic chemistry. Another major theme is the multiple layers of shielding of planetary surfaces from th...

International Nuclear Information System (INIS)

Those materials that can be extracted from pine or oak by ether, ethanol, methyl methacrylate (MMA), or benzene--alcohol all act as inhibitors in the #gamma# polymerization of MMA--wood composites. It was found that preirradiation of either the wood or of the wood--monomer combination reduces or eliminates the inhibitory effect. The most practical industrial solution to this problem is to increase the dose, thereby achieving high molecular polymer in the composite. However, the presence of a maximum in the molecular weight--dose curves means that each wood--monomer pair may have a different optimum dose.

Energy Technology Data Exchange (ETDEWEB)

The effect of high-energy-density laser surface melting on the morphology and properties of a cast Ni-based superalloy containing 33 wt percent Mo and 17 wt percent W is investigated experimentally. Significant improvements in the hardness and the wear resistance in both dry and acid environments are atttributed to the elimination of segregation in the laser-treated zone, where solid solubility increases, crystalline structure becomes finer, and the fine dendritic, cellular dendritic, cellular, and plane-front solidification structures are evenly distributed.

International Nuclear Information System (INIS)

The methods of optical and transmission electron microscopy were used to study the influence of different programmes of hot deformation on the structure formation of (#alpha#+#beta#) titanium alloy VT9. The #beta# alloy VT-15 was studied at the same time in order to simulate the dislocation structure generated in the process of hot deformation. During the hot deformation of two-phase titanium alloys in both #beta# and (#alpha#+#beta#) ranges there is found to be an optimum range of deformation in which a homogeneous, polygonized structure is formed.

International Nuclear Information System (INIS)

Electron beam therapy has often been used for radiation therapy of carcinomas of the buccal mucosa, though side effects, including stomatitis and dermatitis, are known to exist. We experimented using the additional back scatter and transit with the phantom under a lead plate within the irradiation field, in order to better focus the dose on the target volume moreover, we fabricated a mouthpiece fitted with a lead plate shaped to the target volume, and with respect to the influence of the mouthpiece on stomatitis and dermatitis, obtained good clinical results. (author).

Science.gov (United States)

The dynamic response characteristics of the VAWT rotor are important factors governing the safety and fatigue life of VAWT systems. The principal problems are the determination of critical rotor speeds (resonances) and the assessment of forced vibration response amplitudes. The solution to these problems is complicated by centrifugal and coriolis effects which can have substantial influence on rotor resonant frequencies and mode shapes. This paper will describe and discuss the primary tools now in use at Sandia National Laboratories for rotor analysis. These tools include a lumped springmass model (VAWTDYN) and also finite-element based approaches. The discussion will center on the accuracy and completeness of current capabilities and plans for future research.

Energy Technology Data Exchange (ETDEWEB)

Comparatively evaluates two models for forecasting ground subsidence after underground mining: a standard method used in Poland in underground coal mining and a method used in the GDR. Factors that influence ground subsidence after underground mining are evaluated. Effects of depth, stratification, and physical and mechanical properties of rock strata are analyzed. Time dependence of dynamic troughs and static final troughs left after underground mining is evaluated. Formulae are recommended for forecasting ground subsidence after underground coal mining and mining of other deposits. 3 refs.

Science.gov (United States)

When induced by bottom heating in a horizontal fluid layer which is characterized by forced motion or solute stratification, buoyancy-driven flows may assume a variety of forms. The flows, which are examples of mixed or double-diffusive convection, can strongly influence heat tranfer or the entrainment of stratified fluid. General aspects of each form of convection are reviewed, and emphasis is placed on mixed convection in a horizontal rectangular channel and on double-diffusive convection due to thermally driven mixed-layer development in a solutally stratified fluids. Flow conditions are described, and experimental and theoretical results are presented for related heat-transfer and entrainment parameters.

Energy Technology Data Exchange (ETDEWEB)

The UFIP (French Petroleum Industry Association) studies concerning polluted sites and soils and their rehabilitation are presented: characterization of the admissible maximum fuel or gas oil content in the ground, the issue of time effects, and the risks it may induce for public health; study on the various pollutant impacts on the environment (underground waters, biotope...); approach to the development of a dynamical model describing these phenomena and their influence on man, in order to derive consistent and reasonable decontamination objectives

Energy Technology Data Exchange (ETDEWEB)

The available experimental data on the (/sup 3/He,n) reaction between the ground states of even-even nuclei and lowest 1/2/sup -/ levels of odd-A nuclei in the Aapprox.=100 region are analyzed in a systematic way by the DWBA. The deduced relative intensities of these two-proton transfers, and their uncertainties, are compared to the predictions of various nuclear models. In particular, the influence of the finite dimension of the configuration space available to the transferred protons, and of the blocking effect of a 2p1/2/sup -/ proton, are examined. (orig.).

International Nuclear Information System (INIS)

The influence of sediment dwelling macroinvertebrates on fate and bioavailability of contaminants in freshwater systems was determined using the burrowing mayfly, Hexagenia limbata, as a representative benthic organism. Two series of experiments were conducted: the first to determine the effect of mayflies on movement of contaminants into sediment and organisms, and the second to examine the effect of mayflies on release of contaminants from sediments to the water column and their subsequent accumulation in fish. Concentrations of "1"4C labelled DDT, hexachlorobenzene (HCB), and dihexylphthalate (DHP) in water were 0.11 +/- 0.01, 0.062 +/- 0.005 and 0.006 +/- 0.007 ppb, respectively. Total mass of DHP in the burrow wall was about equal to mass on the surface, indicating that mayflies were capable of doubling the amount of DHP sorbed per unit surface area of sediment. Adsorption of contaminants from water pumped through ...

Energy Technology Data Exchange (ETDEWEB)

A large variety of microwave producing devices are used in contemporary naval communications and weapons systems. Public and scientific concern about potential biological effects of microwave irradiation such as produced by these various devices requires documentations of such effects. Currently, the only well documented direct effect of microwaves is heating of the exposed organism. The present report is of a series of studies whose aim was to explore several microwave frequencies and their effect on performance and simultaneously to investigate the relationship to core heating in the exposed animals. Three difficult sized species of animals were used so that generalization to larger animals could be made. Rats, squirrel monkeys, and rhesus monkeys showed consistent effects of 60-minute exposures to microwaves when their body temperatures were increased at least 1 C above baseline ...

Energy Technology Data Exchange (ETDEWEB)

The influence of low-level microwaves (2.45 GHz, CW, 2 and 5 mW.cm/sup -2/) was studied on various models of previsional animal psychopharmacology involving tests of motor activity, stereotypy, convulsions and hypothermia after a standard 30 min irradiation. The results obtained on 933 rodents allow to conclude that: (1) there is no interaction between microwaves and the studied convulsants and stimulants; (2) there is a possibility of potentialization of the behavioral effects of a tranquilizer; (3) there is a thermogenic effect of microwaves; (4) there is no change of the blood-brain barrier permeability. The demonstration of a thermal effect of microwaves during radiations lower than 10 mW.cm/sup -2/ the safety threshold admitted presently (a value below which the exposure duration comes under regulation) could explain the energetic nature of certain effects of microwaves ...

British Library Electronic Table of Contents (United Kingdom)

The fossil fuel consumption and pollutant emissions in a coal fired fluidized bed boiler could be reduced by biomass pyrolysis gas reburning. The influence of three kinds of biomass pyrolysis gases on the emission of N2O in a laboratory scale fluidized bed was investigated using the mechanism of GRI3.0 in this paper. The results showed that: the effect of sawdust pyrolysis gas reburning on N2O was more significant than that of rice husk and orange peel under the same conditions; the increase of initial oxygen content from 1% to 8% in flue gas would restrain the decomposition of N2O; the N2O decomposition was enhanced by increasing reaction temperature from 1073.15 K to 1323.15 K, and the decomposition rate may reach 99% at 1223.15 K.

British Library Electronic Table of Contents (United Kingdom)

Abstract Trametes hirsuta, a filamentous basidiomycete, was successfully cultivated in solid-state fermentation (SSF) on a mixture of pine wood chips and orange peel in a novel bioreactor that allows mixing of the inoculated solid material during the fermentation. Copper sulfate or xylidine (2,5-dimethylaniline) were added to enhance the production of enzymes, especially laccases. For comparison, Trametes hirsuta was also cultivated in submerged conditions. The effect of additives in SSF was low, whereas the choice of the solid material and the rotation of the reactor vessel showed a significant influence on the enzyme production. The space-time yields for the fermentations were calculated and showed that SSF on low-cost substrates can effectively produce extracellular enzymes at a suffici...

British Library Electronic Table of Contents (United Kingdom)

Bisphenol-A (BPA) is one of the most common environmental endocrine disrupters and has a wide range of effects on central nervous system. Adolescence is another important developmental period besides the early critical prenatal and neonatal periods. In the present study, we exposed mice to BPA (40, 400 mg/kg/d) between adolescence and young adulthood for 8 weeks and investigated its effects on the non-reproductive behaviors. In open field tests, rearing and grooming sex differences were abolished by BPA exposure. In the elevated plus maze test, the number of open arm entries, the time spent in open arms, and the number of unprotected head dips in the center area were reduced in males but increased in females by BPA at 40 or 400 mg/kg/d, thus eliminating or reversing sex differences in thes...

British Library Electronic Table of Contents (United Kingdom)

Summary Background Current management of egg allergy relies on egg elimination from the diet. It does not protect patients from reactions after accidental ingestion of the food and it has a negative influence on quality of life. To solve these problems, some desensitization protocols have been described that are safe and effective, but only one study of a rush regimen for egg with a small patient sample has been published. Objective To evaluate the safety, efficacy and immunologic effects of an oral rush desensitization protocol for immediate egg allergy. Methods Subjects aged 5 years or older with symptomatic IgE-mediated allergy to hen's egg underwent a 5-day oral tolerance induction regimen and were subsequently maintained on a regular egg intake. The variables studied were the reaction...

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on Alloy UNS N06690 were investigated in simulated crevice chemistries. It was found the role of lead in corrosion processes is strongly dependent on the pH value of the testing solutions. At pH 1.5 the effect of lead is narrowly noticeable; while at pH 12.7, lead has a significant influence on the electrochemical performance of alloy UNS N06690. The lead alters the surface morphologies at both pH and account for higher hydroxide content in the surface film at pH 12.7. The lead incorporation hinders the formation of spinel oxides during the passivation in alkaline solution. Nanoindentation tests indicate a significant lead-induced degradation in the mechanical properties of passive films. The passivation degradation is attributed to detrimental effects of lead via interrupting the dehydration process and hindering the formation of protective layers on the alloy surface.

British Library Electronic Table of Contents (United Kingdom)

An analysis is presented for the effects of chemical reaction and thermal radiation on hydromagnetic free convection heat and mass transfer for a micropolar fluid via a porous medium bounded by a semi-infinite vertical porous plate in the presence of heat generation. The plate moves with a constant velocity in the longitudinal direction and the free stream velocity follows an exponentially small perturbation law. A uniform magnetic field acts perpendicularly to the porous surface in which absorbs the micropolar fluid with a suction velocity varying with time. Analytical expressions are computed numerically. Numerical calculations are carried out the purpose of the discussion of the results which are shown on graphs and the effects of the various dimensionless parameters entering into the p...

British Library Electronic Table of Contents (United Kingdom)

Arauzo-Carod J.-M. and Viladecans-Marsal E. Industrial location at the intra-metropolitan level: the role of agglomeration economies, Regional Studies. The objective of this paper is to analyse the influence of agglomeration economies on location decisions taken by new firms inside metropolitan areas. As it is assumed that these economies differ according to firms' level of technology, the sample comprises new firms from high-, intermediate- and low-technology industries. Of particularly interest is in analysing the effects of agglomeration economies that are felt over very short distances (inside the metropolitan areas). Introduced in the estimation is the effect of the central city as a determinant for the location of new firms in the rest of the metropolitan area. [image omitted] Arauzo...

International Nuclear Information System (INIS)

A study was made into microstructure and texture of cold rolled titanium alloy VT-35 with various hydrogen content aimed to reveal hydrogen influence on the mechanism of cold plastic deformation by rolling. Experiments were carried out using sheets 1.2 mm thick hydrogenated up to hydrogen concentrations from 0.06 to 0.554 mass. %. All specimens constituted a single-phase FCC #beta#-solid solution. It is shown that small hydrogen additions have a plasticizing effect on #beta#-titanium alloys in their cold rolling. The character of texture is dependent on hydrogen concentration and determined by deformation mechanism. 6 refs.; 5 figs.

Science.gov (United States)

Phytoremediation has been identified as a potentially environmentally friendly and cost effective technique for the treatment of contaminated soil. However, phytoremediation has an unknown mechanism. In this study, we focus on the effects of the cultivation of Italian ryegrass on the soil microbes collected at oil showings, which were expected to have a variety of crude oil degradable microorganisms. We evaluated the number of crude oil degradable microorganism, microbial activity, microflora using the PCR-DGGE method and the change in the concentration of crude oil in the soil. The results indicated that the microflora was affected by the cultivation of Itarian ryegrass, and that the microbial activity and the number of crude oil degradable microorganisms were also improved by the cultivation. Moreover, the concentration of crude oil in the rhizosphere soil decreased significantly when compared to the uncultivated soil. These results suggested ...

Energy Technology Data Exchange (ETDEWEB)

The unburned HC in a direct-injection diesel engine is a cause of exhaust odor and SOF emission. Reduction of HC by changing the injection nozzle specifications was attempted in previous studies. In this study, some experiments in which the mixture formation was varied by using different hole diameters in a multihole nozzle and spray angles to the combustion chamber wall have been conducted. When the diameter of injection holes, which influences the fuel adhering to on the cylinder head walls and the combustion chamber wall, becomes smaller, the HC emission in the idling condition, HC deviation from cylinder to cylinder and HC increase with long idling time are decreased. The same effects were obtained by decreasing the diameter of all holes and by injecting the spray downward to the combustion chamber. 13 refs., 13 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

The effects of boron addition on weldability and high temperature strength properties were investigated for Hastelloy alloy XR used TIG welding process with the filler metals. Four versions of filler metals with different boron contents were used. The results obtained may be summarized as follows: (1) The influence of boron addition on weldability was not observed within the range of the present experiment. (2) The result of chemical analysis for deposited metals showed that boron desorption did not occur during welding. (3) The tensile properties of weldments, particularly in high temperature ductility were raised with increasing boron content. (4) In the creep properties of weldments, creep rupture life increased with increasing boron content under the given stress conditions. (author).

British Library Electronic Table of Contents (United Kingdom)

Thirty fattened one humped desert camels were used to examine the effect of season on contractile and metabolic properties of Longissimus thoracis (LT) muscle. Ten camels were slaughtered according to seasons of the year (winter, summer and autumn). Season significantly influenced muscle chemical composition, ultimate pH (pHu) and color. Activities of metabolic enzymes were higher during autumn season compared to summer and winter for phosphofructokinase (+64% compared to both seasons) and for isocitrate dehydrogenase (+35% and +145% in autumn vs. summer and winter, respectively). Quantification of muscle myosin heavy chain isoforms by SDS-PAGE electrophoresis showed only presence of type I and type IIa MyHC in camel muscle and indicated high proportion in winter for type I and in autumn f...

British Library Electronic Table of Contents (United Kingdom)

Statement of problem Titanium is the most biocompatible metal used for dental casting; however, there is concern about its marginal accuracy after porcelain application since this aspect has direct influence on marginal fit. Purpose The purpose of this study was to determine the effect that metal selection and the porcelain firing procedure have on the marginal accuracy of metal ceramic prostheses. Material and methods Cast CP Ti, milled CP Ti, cast Ti-6Al-7Nb, and cast Ni-Cr copings (n=5) were fired with compatible porcelains (Triceram for titanium-based metals and VITA VMK 95 for Ni-Cr alloy). The Ni-Cr alloy fired with its porcelain served as the control. Photographs of metal copings placed on a master die were made. Marginal discrepancy was determined on the photographs using an image ...

International Nuclear Information System (INIS)

Radiation modification on liquid retention properties of native cassava starch, gelatinized at 85"0C, by graft copolymerization with acrylonitrile was carried out by mutual irradiation to #gamma#-rays. A thin aluminium foil was used to cover the inner wall of the reaction vessel so that the extent of homo polymer could be reduced to be less than 1.6% with a distilled water retention value of 665 g/g of the dry weight of the saponified grafted product. Confirmations of graft copolymerization and saponification reactions were made by the infrared spectrophotometric technique. The combined effect of radiation parameters in terms of an irradiation time and a dose rate to the same total dose on the extent of grafting reaction expressed in terms of grafting parameters which directly influenced liquid retention values was evaluated in conjunction with statistical analysis.

British Library Electronic Table of Contents (United Kingdom)

Abstract Aim- Two alternative hypotheses attempt to explain the upper elevation limit of tree lines world-wide, the carbon-limitation hypothesis (CLH) and the growth-limitation hypothesis (GLH); the altitudinal decrease of temperature is considered the driver constraining either carbon gain or growth. Using a widely distributed tree line species (Nothofagus pumilio) we tested whether tree line altitude is explained by the CLH or the GLH, distinguishing local from global effects. We elaborated expectations based on most probable trends of carbon charging with altitude according to both hypotheses, considering the alternative effects of drought. Location- Two climatically contrasting tree line ecotones in the southern Andes of Chile: Mediterranean (3654- S) and Patagonia (4604- S). Methods- ...

International Nuclear Information System (INIS)

The dithiocarbamate and thiuram compounds, including disulfiram, were compared for their efficacies in influencing tissue distribution of a trace dose of intravenously injected lead plus "2"0"3Pb in rats. The tested compounds were sodium diethyldithiocarbamate (DEDTC), sodium dimethyldithiocarbamate (DMDTC), tetraethylthiuram disulfide (disulfiram), a complex of zinc and manganese ethylenebisdithiocarbamate (mancozeb), manganese ethylenebisdithiocarbamate (maneb), sodium monomethyldithiocarbamate (metham), zinc propylene bisdithiocarbamate (propineb), tetramethylthiuram disulfide (thiram), zinc ethylenebisdithiocarbamate (zineb), and zinc dimethyldithiocarbamate (ziram). The results of this study show that interactions can occur between lead and DEDTC, DMDTC, disulfiram, metham, thiram, and ziram, resulting in increased levels of lead in brain and probably potentiation of the neurotoxic effects of lead.

Energy Technology Data Exchange (ETDEWEB)

For the purposes of energy forests, biological pest control should be interpreted as any method of using natural organisms or their products for the regulation of herbivores, below the economic threshold. The organisms include the energy forest crop species and natural enemies of pest herbivores. Examples are provided of three-trophic-level interactions, including some on willows and poplars. Bottom-up effects may be particularly strong in juvenile Salicaceae, which are used in energy forest production, because plants are growing vigorously, and many herbivores respond positively. Some major pests on willows and poplars appear to have weak top-down regulation, and they may be influenced most by bottom-up effects such as plant resistance through genetic variation, ontogenetic aging and physiological aging. Balancing the bottom-up and top-down forces in energy forests may be difficult in short-rotation crops, but harvesting ...

British Library Electronic Table of Contents (United Kingdom)

In this paper, the unsteady MHD free convection heat and mass transfer of viscous fluid flowing through a Darcian porous regime adjacent to a moving vertical semi-infinite plate under Soret and Dufour effect have been examined. Viscous dissipation effects are included in the energy equation. A uniform magnetic field is applied transversely to the direction of the flow. The differential equations governing the problem have been transformed by a similarity transformation into a system of non-dimensional differential equations which are solved numerically by element free Galerkin method. The influence of Grashof number (Gr), magnetic parameter (M), heat absorption parameter (Q), permeability parameter (K), Schmidt number (Sc), Soret number (Sr), and Dufour number (Du) on the velocity, tempera...

Energy Technology Data Exchange (ETDEWEB)

The biomedical and ecological interest for the microwave impact on the Earth biosphere is continuously increased since the industrial, military and communication activities strongly contribute to the electromagnetic stress of living bodies. In the next the authors present some of the main results obtained regarding the microwave exposure of various types of biological material: bacteria, fungi, young plant seedlings, dry seeds, animal tissues. The electromagnetic exposure was carried out in open space in well controlled environmental conditions by using 10.75 GHz/1 m W cm{sup -2} microwaves. Biochemical assays and cytogenetic tests have been carried out to reveal the changes induced post irradiation. The response of some pathogen bacteria, have been emphasized by means of turbidimetric measurements - the stimulatory effect being noticed at the level of the microbial population density (the stimulation of the human body microbial flora seems to be one of the side ...

Energy Technology Data Exchange (ETDEWEB)

The oxidative dehydrogenation (ODH) of light alkanes is an alternative way for the production of olefins. A wide variety of catalytic systems has been investigated. Vanadium oxide based catalysts were described in the literature as effective catalysts for the ODH of propane. The catalytic activity and selectivity depend on the kind of support material, the kind of dopants and the formation of complex metal oxide phases. In recent papers it was claimed that both orthovanadate and/or pyrovanadate species are selective for the ODH of propane. Niobia based materials were investigated as catalysts for acidic and selective oxidation type reactions. In the ODH of propane niobia exhibited a high selectivity to propene but the conversion of propane was low. V{sub 2}O{sub 5}-Nb{sub 2}O{sub 5} catalysts proved to be catalytically active and selective and showed no formation of oxygenates. In the present study the influence of the niobia dopant of the ...

Science.gov (United States)

Prairie (Microtus ochrogaster) and meadow voles (M. pennsylvanicus) are closely related species that differ in life strategy and social behaviors, and thus provide an excellent comparative model for the study of neuronal and hormonal mechanisms underlying behavior. In the present study using the elevated plus maze (EPM) test, we found that male prairie voles entered the open arms of the EPM more and remained there longer, and showed a higher level of overall locomotor activity than did male meadow voles. In addition, two weeks of social isolation induced an increase in open arm entries in prairie, but not meadow, voles. Prairie voles also had a higher level of circulating corticosterone compared to meadow voles, and the EPM test increased circulating corticosterone in prairie voles. Finally, social isolation coupled with the EPM test influenced Fos-immunoreactive expression in several brain areas, including the medial preoptic area, ventromedial hypothalamus, ...

Energy Technology Data Exchange (ETDEWEB)

A numerical investigation of a humidification dehumidification desalination (HDD) process using solar energy is presented. The HDD system consists mainly of a concentrating solar water heating collector, flat plate solar air heating collector, humidifying tower and dehumidifying exchanger. Two separate circulating loops constitute the HDD system, the first for heating the feed water and the second for heating air. A mathematical model is developed, simulating the HDD system, to study the influence of the different system configurations, weather and operating conditions on the system productivity. The model validity is examined by comparing the theoretical and experimental results of the same authors. It is found that the results of the developed mathematical model are in good agreement with the experimental results and other published works. The results show also that the productivity of the unit is strongly influenced by the air flow rate, ...

Energy Technology Data Exchange (ETDEWEB)

Squeeze film dampers (SFD) are devices utilized to control vibrations of the shafts of high-speed rotating machinery. The SFD - squirrel cage combination is probably the most used system for tuning the stiffness and damping of the supports for rotors installed on ball bearings. Squeeze film dampers are essentially hydrodynamic bearings which contain the ball bearings housings of ball-bearings supported shafts. Consequently, the oil film within the SFD are influenced only by the precession and nutation of the shaft, that is the flow of the oil within the damper is not directly influenced by the spin of the rotor. However, in the classical theory, the flow in the thin film is also governed by the Reynolds equation. In this paper, some of the limits of the classical theory of the SFD are discussed and theoretical and experimental studies, which illustrate the ideas presented herein, are presented as well. The orbits of an unbalanced rotor that is ...

Energy Technology Data Exchange (ETDEWEB)

The influence of the velocity profile at the inlet boundary on the simulation of air velocity distribution inside an electrostatic precipitator is presented in this study. Measurements and simulations were performed in a duct and an electrostatic precipitator (ESP). A four-hole cobra probe was used for the measurement of velocity distribution. The flow simulation was performed by using the computational fluid dynamics (CFD) code FLUENT. Numerical calculations for the air flow were carried out by solving the Reynolds-averaged Navier-Stokes equations coupled with the realizable k-{epsilon} turbulence model equations. Simulations were performed with two different velocity profiles at the inlet boundary - one with a uniform (ideal) velocity profile and the other with a non-uniform (real) velocity profile to demonstrate the effect of velocity inlet boundary condition on the flow simulation results inside an ESP. The real velocity profile was ...

Energy Technology Data Exchange (ETDEWEB)

A field study (1993-96) assessed the benefits of applying unusually high rates of coal fly ash from power plants as a soil amendment to enhance water retention of soils without adversely affecting growth and marketability of the turf species, centipedegrass (Eremochloa ophiuroides (Munro) Hack.) A Latin Square plot design was employed that included 0 (control, no fly ash applied), 280, 560 and 1120 MgHa {sup -1} application rates of unweathered precipitator fly ash. The fly ash was spread evenly over each plot area, rototilled, and allowed to weather under natural conditions for 8 months before seeding. High levels of soluble salts, indicated by the electrical conductivity of soil extracts, in tandem with an apparent phytotoxic effect from boron, apparently inhibited initial plant establishment as shown by substantially lower germination counts in treated soil. However, plant height and rooting depth were not adversely affected, as were the dry matter yields ...

International Nuclear Information System (INIS)

A series of spinel Li4Ti5O12 samples were synthesized via a composite molten-salt method (CMSM) using the mixtures of LiCl and KCl with different L values (L is defined as the molar ratio of LiCl:KCl) as the reaction media. It is found that the melting point of the composite molten salt can effectively influence the formation of particles, and leads to different electrochemical performances of the as-prepare Li4Ti5O12. The investigations of X-ray diffraction (XRD), particle size distribution (PSD), Brunauer-Emmet-Teller (BET) surface area, and scanning electron microscopy (SEM) indicate that the as-prepared Li4Ti5O12 with L = 1.5 is a pure phase, and has uniform homogeneous octahedral shape particles, rather narrow PSD, and high BET surface area. Electrochemical tests show that the optimized Li4Ti5O12 with L = 1.5 has an initial discharge capacity of 169 mAh g-1 and an initial charge-discharge efficiency of 94% at 0.2 C rate, and achieves good ...

Energy Technology Data Exchange (ETDEWEB)

An experimental rig was set up to study the performance of a thermal storage unit using stearic acid as the heat storage medium. The unit mainly consists of an electrical heating rod and an outer tube, and the space between is an annulus that is filled with stearic acid. The thermal performance of the unit is measured, and the heat transfer characteristics of the melting processes of stearic acid are studied under different heat flux conditions to determine the influence of heat flux on the melting processes. A new type of fin is designed and fixed to the electrical heating rod to enhance the thermal response of the stearic acid. The experimental results show that the fin can improve the heat transfer of the melting process of the thermal storage unit greatly. The equivalent thermal conductivity of the PCM can be augmented by a factor up to 3. The analysis of the experimental results shows that the enhancement mechanism of the fin is attributed to its ability to ...

Energy Technology Data Exchange (ETDEWEB)

The fertilizer contribution to radio uptake by tomato plants was assessed. Tomato and soil samples from four different plantations were analyzed: two using organic fertilizer and two using phosphate fertilizer. The Ra concentrations in eight of the most used tomato fertilizers were determined. The concentration values ranged from 14 to 221 Bq/kg of Ra-226 and from 25 to 176 Bq/kg of Ra-228. Owing to the low Ra concentration and to the used fertilizer quantities, the fertilizers would not increase significantly the Ra soil concentration. However, the highest soil to plant concentration ratios were found in the plantations using phosphate fertilizers. This outcome pointed out the higher Ra availability in the phosphate fertilizer plantations than in the organic fertilizer plantations, showing a possible positive influence of phosphate fertilizers for the tomato Ra uptake. Due to the phosphate fertilizer used, the dose could increase from 0,05 Sv/year to 0,24 Sv/year. ...

International Nuclear Information System (INIS)

A series of lab and greenhouse studies were undertaken to understand how Cu and Zn toxicity influences Bromus carinatus (Hook and Arn.) growth, to what degree an organic amendment (yard waste compost) may reduce Cu and Zn bioavailability in Cu-Zn minespoil and promote plant growth in combination with fertilizer, and how the vertical distribution of compost in the minespoil influences rooting depth. Root Cu and Zn toxicity thresholds were determined to be 1 mg L"-"1 and 10 mg L"-"1 in solution, respectively. The compost amendment had exceptionally high Cu and Zn binding capacities (0.17 and 0.08 g metal g C"-"1, for Cu and Zn, respectively) that were attributed to high compost humic and fulvic acid concentrations. Maximum plant biomass was achieved when minespoil was amended with compost and fertilizer in combination. Fertilizer alone had no effect on plant growth. Mixing compost into the minespoil was essential to promote ...

International Nuclear Information System (INIS)

The effect of a carbohydrate, a 20% protein, or a carbohydrate +0.3% tryptophan TRP breakfast on plasma large neutral amino acid ratio was studied in 6 healthy men. The carbohydrate-rich meal produced shifts in plasma amino acid concentrations such that plasma TRP/LNAA ratios increased from 0.13 to 0.15 (p<0.04) and the protein meal decreased the ratio from 0.14 to 0.11 (p<0.04) after 1 hour. Addition of 0.3% TRP to the carbohydrate-rich meal increased plasma TRP/LNAA ratios more than 2-fold. The TRP containing meal was thus the only one likely to influence brain 5-HT synthesis, although the difference between the plasma TRP/LNAA ratios after carbohydrate and protein breakfasts suggests that the brain may distinguish, by synthesizing more or less 5-HT, the composition of breakfast meals. (Author).

International Nuclear Information System (INIS)

A brain weight deficit of about 70 mg was induced at doses of approximately 75-mGy and a deficit of 60 mg was induced at 100 mGy. This confirms the effects projected and observed by Wanner and Edwards. Although the data do not demonstrate a clear dose-response relationship between the 75-mGy and 100-mGy groups, the data are statistically consistent with a dose-response effect because of the overlapping confidence intervals. The lack of a statistically significant observation is most likely related to the small difference in doses and the limited numbers of animals examined. There are several factors that can influence the brain weight of guinea pig pups, such as caging and housing conditions, the sex of the animal, and litter size. These should be taken into account for accurate analysis. Dam weight did not appear to have a significant effect. The confirmation of a micrencephalic ...

Energy Technology Data Exchange (ETDEWEB)

With regard to long-term high-temperature strength, molybdenum is an effective alloying element but rather expensive as well. The author describes its influence on high-temperature strength properties of CrMoV alloyed steel. Besides molybdenum, also vanadium and carbon have an increasing effect on limiting rupture stress which furthermore may be effected by heat treatment, the cooling rate being a dominating factor in this process. To guarantee optimum long-term high-temperature strength properties, a minimum of a least 0.5% Mo and 0.35% V is required. The cooling rate after austentizing must be high enough to enable transformation in the bainitic structure to take place. A two-to-three-hour tempering treatment at about 720/sup 0/C is regarded as an optimum.

International Nuclear Information System (INIS)

The cross section and activity profile of different radioisotopes produced by #alpha#-induced nuclear reaction on natural zirconium, have been obtained by stacked foil activation using 40 MeV #alpha#-particles from Variable Energy Cyclotron (VEC) machine at Calcutta. The activity profile would be used to study the surface loss of zircaloy materials of engineering components by thin layer activation (TLA) technique. Generally, isotopes with suitable #gamma#-rays and long half-lives are the most useful in TLA technique, e.g., "9"2Nb, "9"5"gNb and "9"5Zr. (author). 2 refs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

The distribution of the alkaline earth elements strontium and barium between the solid phases of phosphates of transition elements of group 4 and chloride melts was studied. The distribution coefficients of strontium and barium were found at T = 700-800/sup 0/C. Phosphates of the type NaM/sub 2//sup (IV)/(PO/sub 4/)/sub 3/, where M/sub (IV)/ represents titanium, zirconium, and hafnium, were used as the solid phases. It was established that there is an enrichment of the precipitates with the distributed components. The distribution coefficient depends on the nature of the solid phase and the temperature. It was suggested that M/sup (II)/ x M/sub 4//sup (IV)/(PO/sub 4/)/sub 6/ is formed in processes of distribution, where M/sup (II)/ represents Sr, Ba.

Energy Technology Data Exchange (ETDEWEB)

In order to improve the well-known short operational life time of BF3 counters, three potential adsorbents for impurity gases (graphite, activated charcoal and a zirconium-aluminum mixture) were introduced into BF3 counters in the form of coating on the aluminum cathode surface. Tests in el fields revealed that a partial coating of activated charcoal provides the best result. The improvement of their operational life in el fields was about three orders of magnitude in terms of tolerable exposure. Many counters with a partial coating of activated charcoal were further tested from the following viewpoints: background noise, vibration and shock, el pulse discrimination, operational life in a neutron field and non-operational in-reactor exposure life. The results were satisfactory for reactor control and protection usage. (author).