WorldWideScience
 
 
1

Model experiment on change of seismic properties of a fracture caused by injecting/draining water; Chusui/haisui ni yoru kison kiretsu no dansei denpa tokusei no henka ni kansuru model jikken  

Energy Technology Data Exchange (ETDEWEB)

Effect of water injection/draining on elastic waves penetrating through cracks is examined by measuring elastic waves before, during, and after the injection/draining of water into/from cracks in presence in granite. Two blocks of rock, with their crack-containing surfaces in contact with each other, are placed in a vessel, and water injection/draining is done through a hole on a vessel bottom side so that water will penetrate into the cracks. When the blocks are dry, there is almost no contact between the cracks, and so no crack penetrating waves are observed. Crack penetrating waves are produced when water is injected, and the position of the receiver sensing the penetrating waves changes as the water level rises. When the water level is lowered from the high water level, the waveform changes again as the level changes. The change in waveform is not so remarkable, however, as that observed during water injection thanks to the water residual in the cracks. It is now inferred that ...

1997-05-27

2

Effects of matrix resin and fiber content on behavior of fatigue crack propagation in continuous-fiber-mat reinforced CP-resin composites; Renzoku sen`i mat kyoka CP resin fukugozai no hiro kiretsu denpa tokusei ni oyobosu bozai oyobi sen`i gan`yuritsu no eikyo  

Energy Technology Data Exchange (ETDEWEB)

The purpose of the present work is to investigate the effects of matrix resin and fiber content on the behavior of fatigue crack propagation in continuous-glass-fiber-mat reinforced CP-resin composites. For this purpose, ductile matrix resin and brittle one are used. These two kinds of resins have the characteristic that the elastic modulus and tensile strength are nearly the same with each other while the elongation is different. The composite specimens are made of these resins and continuous grass fiber mat of 20 wt.% and 60 wt% fiber contents. The fatigue crack propagation test was conducted by using the tapered DCB specimens to control the stress intensity factor range, {delta}K, during the test. The results obtained are as follows; (1) The relation between the crack propagation rate, da/dN, and {delta}K for all the present materials is shown by a straight line in logarithmic representation. (2) For the composites of 20 wt.% fiber content, the da/dN of the ductile matrix composite ...

1996-05-15

3

Detection of shear-wave traveltime delay by using wavelet transform and characterization of an artificial subsurface fracture; Wavelet henkan ni yoru toka S ha denpa jikan henka no koseido kenshutsu to jinko chika kiretsu no seijo hyoka  

Energy Technology Data Exchange (ETDEWEB)

As characterization of artificial cracks formed underground by using the water pressure fracturing method, experiments have been carried out to detect relationship of pressurization and S-wave propagation time with the polarizing direction dependence. Openings are created when pressure in the vicinity of the artificial cracks increases greater than reopening pressure of micro cracks. Elastic wave velocity decreases in this region because of water in the opened micro cracks. Anisotropy is created in the S-wave propagation velocity due to influence from anisotropic reopening region when the artificial cracks are pressurized, and is separated into two components which polarize orthogonally with each other (micro splitting). Field experiments conducted at the Higashi-hachimantai field were analyzed by using wavelet transform. It was possible to detect the S-wave arrival time at high accuracy, and the arrival of an orthogonally polarized wave was observed in 0.03 to 0.11 ms after the ...

1997-05-27

4

Integrated interpretation of AE clusters and fracture system in Hijiori HDR artificial reservoir; Hijiori koon gantai jinko choryuso no AE cluster to kiretsu system ni kansuru togoteki kaishaku  

Energy Technology Data Exchange (ETDEWEB)

With regard to a fracture system in the Hijiori hot dry rock artificial reservoir, an attempt was made on an interpretation which integrates different data. Major factors that characterize development and performance of an artificial reservoir are composed of a fracture system in rocks, which acts as circulating water paths, a heat exchange face and a reservoir space. The system relates not only with crack density distribution, but also with cracks activated by water pressure fracturing, cracks generating acoustic emission (AE), and cracks working as major flow paths, all of which are characterized by having respective behaviors and roles. Characteristics are shown on AE cluster distribution, crack distribution, production zone and estimated stress fields. Mutual relationship among these elements was discussed based on the Coulomb`s theory. The most important paths are characterized by distribution of slippery cracks. Directions and appearance frequencies of the slippery cracks affect ...

1997-05-27

5

Fracture inspection by BHTV logging through a vinyl chloride tube; Enbi pipe ga sonyusareta kosei deno BHTV ni yoru kiretsu chosa  

Energy Technology Data Exchange (ETDEWEB)

A borehole televiewer (BHTV) logging was conducted to investigate cracks in bored wells. The logging process shoots ultrasonic waves onto bore walls and utilizes reflection waves from the bore walls. If the bores are filled with muddy water, or the ultrasonic waves can pass through even if vinyl chloride tubes have been inserted after excavation, the state of the bore walls can be investigated in principle. Conventional optical scanners are, however, incapable of making this investigation. The BHTV logging can be used for identifying lithofacies from reflection intensities from bore walls (it depends on sound impedance of rocks), not to speak of finding cracks. As a result of making logging upon setting time windows from 105 to 145 {mu} sec in a bored well inserted with a vinyl chloride tube, cracks in the bore wall were identified clearly through the vinyl chloride tube. If the distance between the bore wall and the vinyl chloride tube becomes smaller, setting the time window becomes ...

1997-05-27

6

Crack healing behavior and high-temperature strength properties in mullite/SiC composite ceramics. Muraito/SiC fukugo ceramics no kiretsu chiyu kyodo to koon kyodo tokusei  

Energy Technology Data Exchange (ETDEWEB)

Discussions were given on mullite/SiC composite ceramics as to crack size dependence of their crack healing behavior, and high-temperature strength properties. Test specimens used in the experiment are sinters of mullite powder added with SiC powder at 20% by volume, and hot-pressed under conditions of a sintering temperature of 1650 degC, time of four hours, and a pressure of 35 MPa. In the experiment, a pre-crack was introduced at the center of a test specimen by using a Vickers hardness meter, and a heat treatment was performed in atmosphere at 1300 degC for one hour. A four-point bending test was conducted in atmosphere as a strength test. Conditions in test specimens were investigated by using SEM observation, a laser microscope and X-ray diffraction. The following findings were obtained as a result of the experiment: the bending strength for the pre-cracked material is about 140 MPa against that of a smooth material of 342 MPa, but it increased to 517 MPa after giving a 1300-degC ...

1998-05-21

7

Crack healing behavior and high-temperature strength properties in Si3N4/SiC composite ceramics. Si3N4/SiC fukugo ceramics no kiretsu chiyu kyodo to koon kyodo tokusei  

Energy Technology Data Exchange (ETDEWEB)

Two kinds of Si3N4/SiC composite ceramics having different sintering auxiliaries were fabricated to investigate reproduction of crack healing phenomenon, effects of sintering auxiliaries on crack healing behavior, optimal crack healing conditions, and high-temperature strength characteristics of crack healed portions. The experiment used sinters added with SiC powder at 20% by volume, and hot-pressed under conditions of a sintering temperature of 1850 degC, time for two hours, and a pressure of 35 MPa. The sintering auxiliaries used are Y2O3 and Al2O3. In the experiment, pre-cracks were introduced into test specimens, and heat treatments were given in atmosphere and in argon gas atmosphere at 1300 degC for one hour. A four-point bending test was conducted in atmosphere as a strength test. The result of the experiment revealed that the materials which were heat-treated in atmosphere have greater crack healing effect, that the optimum heat treatment temperature differs largely according ...

1998-05-21