International Nuclear Information System (INIS)

The usage of biosorbents allows separation of scandium and yttrium from each other and from Fe, Al, Ti, Si, and Ca in hydrometallurgical processing of ores and wastes. It was shown that sorption of scandium and yttrium increased with the increase of pH of solution. Initial rate of scandium sorption depended on the biomass type; however 85-98% of scandium was sorbed within 10-30 min with most biomass types tested. The presence of aluminium, iron (III), and titanium in the solution inhibited sorption of scandium and particularly yttrium. After four cycles of sorption, 98.8% of scandium and 87% of yttrium was extracted from red mud leach solution by the biomass of Saccharomyces cerevisiae and Aspergillus terreus, respectively. Selectively of the process of scandium and yttrium recovery could be achieved during sorption and also desorption, when solubilization of ...

Science.gov (United States)

films and cylinders of rare earth doped yttrium aluminum garnets. ... We knew that yttrium aluminum garnet (YAG) could be doped with ...

Science.gov (United States)

Metastable yttrium-oxide films are synthesized using reactive sputter deposition. The yttrium concentration of the as-deposited film is found to vary as a function of the sputter deposition rate. In addition to the synthesis of the cubic equilibrium phase...

International Nuclear Information System (INIS)

Short communication.

CERN Document Server

Safe management of wastes from the mining and milling of Uranium and Thorium ores

International Nuclear Information System (INIS)

The effect of the rare earth element, yttrium, on the mechanical properties of 9Cr-2WVTa low active martensite steel for fusion reactor was studied and the metallurgical behavior of yttrium in the steel was primarily analyzed. The results show that it is easy for yttrium to aggregate and form the blocky yttrium rich inclusions in the steel, which can dissever the continuity of the matrix and produce micro-cracks for fracture. The yttrium rich inclusions were distributed along the rolling direction, which made the fracture surface delaminated in the tensile and impact samples, and reduced the mechanical properties of the steel. (authors)

Science.gov (United States)

PMID:21540757

Energy Technology Data Exchange (ETDEWEB)

A test to determine the lithium compatibility and impurity gettering capabilities of various materials including yttrium was performed in Beryllium-7 Experimental Lithium (7BELL) at 270/sup 0/C. Yttrium coupons were exposed in liquid lithium for a total of 3,718 hours. X-ray diffraction and bulk chemical analysis data indicated that yttrium absorbs hydrogen from liquid lithium at 270/sup 0/C and transforms to yttrium dihydride (YH/sub 2/). The transformation of yttrium to YH/sub 2/ resulted in embrittlement of the coupons and subsequent fragmentation to small pieces. Additional analysis, based on the equilibrium hydrogen pressures for the transition of yttrium to YH/sub 2/, and Sievert's relationship for hydrogen in equilibrium with hydrogen in lithium, indicates that the temperature of yttrium cannot exceed 280/sup 0/C to control ...

Science.gov (United States)

... Accession Number : ADD141533. Title : Yttrium Oxides in Vacuum-Plasma- Sprayed CoNiCrAlY Coatings,. Descriptive Note : Journal Article,. ...

Science.gov (United States)

... Title : Influence of Yttrium Addition and Superficial Y(sub 2)O(sub 3) Powder Application to Fe-26Cr-21Ni-1.8Si Alloy on Its High Temperature ...

International Nuclear Information System (INIS)

Published in summary form only.

International Nuclear Information System (INIS)

Carrier-free "8"8Y radioisotope, which has the longest half life (T=106.6 d) of yttrium radioisotopes and is a #gamma#-ray emitter, was obtained by proton irradiation of strontium, followed by cooling for one month. Then, "8"8Y was purified by precipitating strontium as strontium nitrate and extracting yttrium with tri-n-butyl phosphate (TBP). The decontamination factor of strontium to yttrium was more than 4x10"3 and chemically pure yttrium radioisotope was obtained. (author) 6 refs.

Energy Technology Data Exchange (ETDEWEB)

This paper advances hypotheses on the chemistry of the interaction of thorium and yttrium with organic-inorganic salts of molybdenum polyacids. On the basis of an analysis of the data of an adsorption experiment and the quantitative relationships that follow from the law of mass action, it is shown that thorium is absorbed by the solid phase by coprecipitation with the participation of complex formation, while the coprecipitation of yttrium with salts of polyacids is due to a reaction of ion exchange chemisorption.

Science.gov (United States)

This document presents the findings of an extensive study of the ore mining and dressing industry, for the purpose of developing effluent limitations guidelines for existing point sources and standards for performance new sources, to implement Sections 30...

Science.gov (United States)

Homestake Ore from the Ambrosia Lake District of New Mexico was treated in the Alkaline Leach-- Filtration Pilot Plant at Grand Junction, Colorado. Detailed information on grinding, leaching, flltration, and precipitation in connection with the processing of this ore is given. Autoclave leaching and continuous yellow cake precipitation were employed. The circuit liquors contnined organic material that was detrimental to clariflcation and precipitation and the results show that ihe ore was amenable to the Alkaline Leach--Filtration process only if a special additive was used. (auth)

Science.gov (United States)

We report significant enhancement in superconducting properties of yttrium substituted Ce1-xYxOFFeAs superconductors. The polycrystalline samples were prepared by two step solid state reaction technique. X-ray diffraction confirmed tetragonal ZrCuSiAs structure with decrease in both a and c lattice parameters on increasing yttrium substitution (with fixed F content). With smaller ion Y in place of Ce, the transition temperature increased by 6 K. Yttrium doping also lead to higher critical fields as well as broader magnetization loops, particularly at elevated temperature.

International Nuclear Information System (INIS)

Investigated are the characteristics of high-temperature plastic deformation the velocity sensitivity of flow stresses, deformation curves, flow stresses, deformation before rupture - as well as the structure of beryllium alloys containing nickel (0.5-4 %), yttrium (0.5-2 %) and aluminium (38 %). The alloys containing nickel (2%) and yttrium (0.5 %) are superplastic, however, deformation before fracture of the alloys is lower than that of the unalloyed beryllium. The singularities of high-temperature plastic flow of the alloys and the causes of deterioration of their plasticity are determined.

Energy Technology Data Exchange (ETDEWEB)

Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily at a reasonable cost. A primary example of this is copper heap leaching, where there are no binders currently encountered in this acidic environment process. As a result, operators of many facilities see a ...

International Nuclear Information System (INIS)

Russian Mar 1973. German Democratic Republic Elovskaya, LT

International Nuclear Information System (INIS)

A computer modelling has been developed for the calculation of mass balance of monazite ore break-down by alkali process at Rare Earth Research and Development Center. The process includes the following units : ore digestion by concentrate NaOH, dissolution of digested ore by HCl, uranium and thorium precipitation and crystallization of Na3PO4 which is by-product from this process. The model named RRDCMBP was prepared in Visual Basic language. The modelling program can be run on personal computer and it is interactive and easy to use. User is able to choose any equipment in each unit process and input data to get output of mass balance results. The model could be helpful in the process analysis for the further process adjustment and development.

International Nuclear Information System (INIS)

Simultaneous exposures of rats and hamsters to inhaled radon daughters, with and without uranium ore dust, were performed daily for five months. Pulmonary pathology developing in 6 to 13 mo after cessation of daily exposures included interstitial fibrosis, emphysema, epithelial hyperplasia, squamous metaplasia, and malignant neoplasia. Rats showed a greater variety and more severe response to these uranium mine inhalation exposures than did hamsters. Inhalation of radon daughters with uranium ore dust displayed the site of greatest damage, including squamous carcinoma, from the nasopharynx to the lungs. Sixty percent of the rats exposed to radon daughters with ore dust developed primary pulmonary carcinomas, providing an appropriate short-term experimental animal model for investigation of respiratory tract carcinogenesis in uranium miners.

International Nuclear Information System (INIS)

The extraction of rare earth elements, yttrium and aluminium from red mud resulting from alumina production with the ion-exchange resin KU-2-8n was studied. Experimental results are presented. The technology of hydrometallurgical processing of pulps obtained by sorption extraction of scandium from red mud is developed. It is shown that in the process of precipitation from sulfate sulfuric acid desorbate it became possible to obtain a high degree of rare earths deposition. The use of sodium hydroxide makes it possible to obtain a maximum deposition of rare earths and aluminium - 99.9 %. Aluminium leaching from crude composite concentrate gives a possibility to get concentrates which 15 - 20 times richer in yttrium and rare earths

British Library Electronic Table of Contents (United Kingdom)

World demand for rare-earth elements and the metal yttrium?which are crucial for novel electronic equipment and green-energy technologies?is increasing rapidly. Several types of seafloor sediment harbour high concentrations of these elements. However, seafloor sediments have not been regarded as a rare-earth element and yttrium resource, because data on the spatial distribution of these deposits are insufficient. Here, we report measurements of the elemental composition of over 2,000 seafloor sediments, sampled at depth intervals of around one metre, at 78 sites that cover a large part of the Pacific Ocean. We show that deep-sea mud contains high concentrations of rare-earth elements and yttrium at numerous sites throughout the eastern South and central North Pacific. We estimate that an a...

International Nuclear Information System (INIS)

This study presents a rapid and selective method for the recovery of lanthanides and yttrium, existing in economically interesting concentrations, from red mud, the byproduct of the alumina production. The leaching process is based on the extraction of these elements with diluted nitric acid from red mud under moderate conditions and without using any preliminary treatment. Several parameters such as leaching agents, contact time, temperature, pressure and solid to liquid ratio were investigated in order to achieve an optimum recovery. The process followed here was selected taking into account its efficiency for the selective recovery of yttrium and lanthanides, but also its suitability for the subsequent liquid-liquid extraction of the leaching solution for the separation of the individual lanthanides. The achieved recovery percentages were for Y about 90%, for the investigated heavy lanthanides (Dy, Er, Yb) up to 70%, for the middle ones (Nd, ...

International Nuclear Information System (INIS)

The separation, concentration, and determination of trace elements in iron ores are described. After the sample has been dissolved, the iron is separated by liquid-liquid extraction with a liquid cation-exchanger, di-(2-ethylhexyl) phosphoric acid. The trace elements aluminium, cadmium, calcium, chromium, cobalt, copper, lead, magnesium, manganese, mercury, potassium, sodium, vanadium, and zinc are determined in the aqueous phase by atomic-absorption spectrophotometry.

International Nuclear Information System (INIS)

Daily exposures of adult beagle dogs to inhaled radon daughters and to uranium ore dust for 4-1/2 to 6 yr have produced respiratory tract carcinomas, at similar cumulative working level months (WLM) of exposures to those which induced carcinomas in uranium miners. Biological data from the beagle-dog experiments can therefore be used for prediction of carcinogenic risk under changing exposure conditions in future uranium miners.

International Nuclear Information System (INIS)

The color centers, which are generated in yttrium-aluminium perovskite (YAP):Nd(1 at.%) and YAP:Er(50 at.%) crystals under the influence of ultraviolet and #gamma#-irradiation, have been studied by absorption spectroscopy. The generated color centers are both stable and transient at room temperature. It is shown that the transient color centers are mainly responsible for the decrease of laser generation efficiency of Nd:YAP and YAP:Er irradiated crystals, although physical mechanisms leading to efficiency decrease are different in these materials. (orig.)

International Nuclear Information System (INIS)

Technologic regimes of cryomotor rotor fabrication are determined. Blanks of yttrium ceramics powder are molded hydrostatically at 400-600 MPa. To confirm the serviceability of electric machines of the considered, a hysteretic 10 W power electric motor with the following dimensions of HTSC-ceramics rotor: external diameter - 56 mm; internal diameter - 45 mm, height - 60 mm, is developed and tested in the liquid nitrogen medium. 8 refs.; 8 figs.; 1 tab.

Energy Technology Data Exchange (ETDEWEB)

X-ray magnetic circular dichroism (XMCD) was used to probe the existence of induced magnetic moments in yttrium iron garnet (YIG) films in which yttrium is partly substituted with lanthanum, lutetium or bismuth. Spin polarization of the 4d states of yttrium and of the 5d states of lanthanum or lutetium was clearly demonstrated. Angular momentum resolved d-DOS of yttrium and lanthanun was shown to be split by the crystal field, the two resolved substructures having opposite magnetic polarization. The existence of a weak orbital moment involving the 6p states of bismuth was definitely established with the detection of a small XMCD signal at the Bi M{sub 1}-edge. Difference spectra also enhanced the visibility of subtle changes in the Fe K-edge XMCD spectra of YIG and {l_brace}Y, Bi{r_brace}IG films. Weak natural X-ray linear dichroism signatures were systematically observed with all iron garnet films and ...

British Library Electronic Table of Contents (United Kingdom)

A multiphase origin of the Cu-Co ores in the western part of the Lufilian fold-and-thrust belt in Central Africa is proposed based on literature, satellite image interpretations and petrographic and fluid inclusion analyses on samples from the stratiform mineralization of Kamoto and Musonoi (DR Congo). The various mineral occurrences in the Katanga Copperbelt can be classified in distinct categories: stratiform, supergene enrichment and vein-type. The stratiform mineralization form the largest group and can be found mainly in Lower Roan (R-2) rocks, which can be identified as ridges on satellite imagery. Ore deposits outside the R-2 occur along lineaments and result often from supergene enrichment.The main phase of the stratiform mineralization in the Katanga Copperbelt occurred during dia...

British Library Electronic Table of Contents (United Kingdom)

The composition and physicochemical properties of Gorlovsk Basin anthracite are studied, with a view to expanding its metallurgical use. In industrial tests, anthracite is employed in smelting hot metal in cupola furnaces, in the production of carbonized products and briquets, in ferroalloy production, in sintering iron ore, and in batch for foundry coke.

Energy Technology Data Exchange (ETDEWEB)

A transition from petroleum~derived jet fuels to blends with Fischer-Tropsch (F~T) fuels, and ultimately fully synthetic hydro-isomerized F-T fuels has raised concern about the fate of plasticizers in nitrile-butadiene rubber a-rings that are contacted by the fuels as this transition occurs. The partitioning of plasticizers and fuel molecules between nitrile a-rings and petroleum-derived, synthetic, and additized-synthetic jet fuels has been measured. Thermal desorption of o-rings soaked in the various jet fuels followed by gas chromatographic analysis with a mass spectrometric detector showed many of the plasticizer and stabilizer compounds were removed from the o-rings regardless of the contact fuel. Fuel molecules were observed to migrate into the o-rings for the petroleum-derived fuel as did both the fuel and additive for a synthetic F-T jet fuel additized with benzyl alcohol, but less for the unadditized synthetic ...

UK PubMed Central (United Kingdom)

The purpose of the work was to quantitatively characterize temperature effects on the bacterial leaching of sulfide ore material containing several sulfide minerals. The leaching was tested at eight...Full Text Available

International Nuclear Information System (INIS)

Certain applications are described of radionuclide X-ray fluorescence analysis in the ore dressing industry, in the manufacture of building materials, in metallurgy, pharmacy, in the chemical, photographic and paper industries, in space exploration, in archeology and for measuring the thicknesses of thin layers of coatings. (ES).

International Nuclear Information System (INIS)

The purpose of the Ocean FUSRAP Program, which began in March 1981, is to assess the technical, environmental, and institutional feasibility of disposing, in the ocean and on the ocean floor, of FUSRAP waste which contains traces of natural radioactive materials. The initial planning has focused on the Middlesex, New Jersey, Sampling Plant site and surrounding properties, which contain on the order of 100,000 metric tons of material. The Belgian Congo uranium ore and other uranium ores used by the United States were handled at the sampling plant site and have since been removed.

International Nuclear Information System (INIS)

A synthesis of scientific knowledge about petroleum biodegradation linked to uranium mineralisation is firstly done. Then the genesis of Huemul Uranium ore deposit (Malargue Town, Mendoza Province) is discussed, where Uranium ore is linked only with one type of asphaltite (there are three other types) from an oil field close by. This asphaltite type would be an efficient natural geological barrier for Uranium migration and it could be linked to a particular kind of biodegradation. The authors think that the International Wonuc Conference would be a good opportunity to discuss a way for future investigations. (author)

International Nuclear Information System (INIS)

This paper presents results of studying the thermo-transferred thermoluminescence (TTTl) phenomenon in potassium-yttrium double fluoride doped with terbium (K_2YF_5_:Tb) at different impurity concentrations (0.8%, 0.95% and 0.99%). Previously to study the TTTl phenomenon, structural characterization and chemical composition of the materials were determined. The structural studies were conducted using a scanning electron microscope; meanwhile, chemical composition was analyzed using energy dispersive X-ray spectroscopy. Thermoluminescence kinetics was studied irradiating the samples with "1"3"7Cs gamma rays as well as with "9"0Sr/"9"0Y beta rays, analyzing the glow curves by the deconvolution method for obtaining the kinetic parameters. (Author)

British Library Electronic Table of Contents (United Kingdom)

Regularities of deformation-induced dissolution of a surface layer of iron oxides in matrixes of iron-based alloys with bcc and fcc lattices have been studied by the methods of M?ssbauer spectroscopy, transmission electron microscopy, and X-ray diffraction. A method of producing iron alloys strengthened by dispersed oxide nanoparticles and alloyed with elements possessing a high affinity to oxygen (titanium and yttrium) has been proposed, which implies a dynamic dissolution of a surface layer of iron oxides upon strong cold deformation and a precipitation of secondary yttrium and titanium nanooxides upon a subsequent high-temperature sintering of mechanically alloyed powders. There has been demonstrated a possibility of oxide strengthening of pure iron upon its interaction with air without...

International Nuclear Information System (INIS)

The effect of yttrium substitution at the lanthanum site on the superconducting properties of La_1_-_xY_xO_0_._9F_0_._1FeAs ('x' = 0, 0.10, 0.20, 0.30, 0.50 and 0.60) oxypnictides has been studied. Powder X-ray diffraction studies confirm single phases till x = 0.1 beyond which minor amount of Y_2O_3 is observed. The temperature dependence of resistivity measurements confirm the superconducting transition temperature (T_c) of 34.8 (#+-#0.05) K and corresponding Meissner transition at 34.3 K in the 'x' = 0.3 composition which is higher than that reported for the parent phase (LaO_0_._9F_0_._1FeAs (T_c = 28 K)). Further increase in the concentration of yttrium leads to broadening and suppression of the superconducting transition. The value of H_c_2 at zero temperature is estimated to be about 60.5 T. The Seebeck coefficient (S) shows a negative sign indicating that the major contribution to the conductivity is by electrons. The Hall coefficient ...

Energy Technology Data Exchange (ETDEWEB)

To determine a suitable combination of X-ray filter and tube kilovoltage for Fuji Computed Radiography (FCR), provide better detection of pulmonary nodules, and reduce patient exposure, we compared observer performance with different X-ray filters and tube voltages. Radiographs were obtained with a copper filter backed by aluminium, with a tungsten filter backed by yttrium and aluminium, and with a lead filter backed by yttrium and aluminium, at both 100 kVp and 135 kVp. Observer performance in detecting simulated lung nodules, which were placed on the posterior aspect of a chest phantom, was compared using receiver operating characteristic (ROC) techniques for each combination of the X-ray filter and tube voltage. The results of the study indicated that (1) nodule detection was superior for the images obtained with 135 kVq as compared with 100 kVp; (2) approximately equal detection rates were obtained for the three X-ray filter sets, although ...

International Nuclear Information System (INIS)

In this paper the effect of adding commercially pure yttria concentrate and yttrium carbonate concentrate (NUCLEMON) on the densification of #beta#-Sialon has been studied. The specimens were sintered in graphite furnace at 1720 and 175 deg C, for 1 hour in a nitrogen atmosphere. Densities of up to 99% of the theoretical density were obtained. Microstructural analyses of the specimens were carried out with the aid of an X ray diffractometer and a scanning electron microscope. (author)

International Nuclear Information System (INIS)

In Japan, the Ningyo-toge uranium deposit was discovered in 1955, and the Tono deposit in 1962. Geology of these mines is different from that of other metal mines developed in Japan. Therefore, it appeared that some changes were required in the usual mining methods applied to existing metal mines to mine uranium ore in these deposits. At the Ningyo-toge mine, effective methods were studied for mining the ore, such as the room and pillar method, long-wall method, slicing method, and the hydraulic method; as a result, it was determined that a modified long-wall method is the most useful and practicable for recovering uranium ore from this underground sedimentary deposit. Applicatons of in-place and microbiological leaching to these deposits are being studied to secure mine safety and decrease mine pollution. Since 1959, when the Ningyo-toge mine went into operation, no hazards for workers nor any pollution of the environment ...

British Library Electronic Table of Contents (United Kingdom)

Investigations have been carried out at the three Corus UK sinter plants over the period 2002-2004 to characterise the emissions of both 2,3,7,8-PCDD/Fs and WHO-12 PCBs, to estimate annual mass releases of these organic micro-pollutants using the I-TEF and WHO-TEF schemes, and to investigate the formation of PCBs in the iron ore sintering process. Results showed that the sintering of iron ore produces a characteristic WHO-12 PCB and PCDD/F congener pattern that is substantially the same for all UK sinter plants. With regard to WHO-12 PCBs, the most abundant congeners were typically PCBs 118 (6-9ngNm-3), 105 (2-4ngNm-3) and 77 (2-3ngNm-3). All other WHO-12 PCBs were also detected at concentrations around 1ngNm-3. All sinter plants investigated exhibited very similar TEQ concentrations. WHO-...

Energy Technology Data Exchange (ETDEWEB)

Radon emanation coefficients of 0.02 to 0.55 were measured at moisture contents ranging from dry to saturation in 18 different ores. The emanation coefficients rose from a minimum when dry to a plateau usually starting at 5 to 20 percent of saturation. A model, using measured pore-size distributions, suggested that the radium mineralization may be confined to annular layers about 0.02 micrometers thick around pores. Radon's diffusion coefficient was determined as a function of moisture. The techniques involved comparing a disk's exhalation as a function of time whether or not the disk had a distributed source. The model was free of approximations and included the effects of porosity and adsorption. An increase of diffusion coefficient with moisture for one or two ores was explained in terms of a model's equation for the diffusion coefficient in terms of both volume and surface diffusion. Radon's adsorption ...

Energy Technology Data Exchange (ETDEWEB)

A patent is claimed for a direct coal liquefication process which is carried out by interaction with a paste, consisting of small-fragment coal, oil and catalysts, with H/sub 2/ at increased temperatures and pressures. The catalyst is a mixture of 1 part per weight of Fe-ore that's been activated by aqueous treatment, and 0.1-1.0 powder-form S. The Fe-ore can be magnetite, limonite, hematite, pyrite, ferrous sand or ''red mud'' (byproduct of the Bayer process), with the ''red mud'' and limonite, having a particle size of about 100 mesh is preferable. Activation of Fe-ore includes aqueous treatment in boiling water for 30-120 min with subsequent drying; annealing at a temp. of 300-700/sup 0/C for 10-120 min; submerging into cold water and final drying. The catalyst is added to the paste in the amount of 0.03-0.3 parts per weight to one part of ...

International Nuclear Information System (INIS)

This study was carried out mainly to produce uranium trioxide (UO_3), matching standard commercial specification from rock phosphate deposits in Uro and Kurun at eastern part of the Nuba Mountains. A simplified hydrometallurgical procedure has been adopted for production of yellow cake from the ore. The powdered ore sample was leached with concentrated H_2SO_4 acid with and without addition of KCIO_3 as an oxidant. The crude yellow cake was precipitated from the resulting green solution of phosphoric acid as Na_2U_2O_7 and (NH_4)_2U_2O_7 and subsequently purified by TBP extraction (tributylphosphate) and hydrogen peroxide as UO_4.2H_2O. TBP purified product was dried and calcined to UO_3 whereas UO_4.2H-2O was dried and reduced to UO_3 by Na_2S_2O_3. Prior to precipitation of crude yellow cake, Fe in the phosphoric acid solution was precipitated using magnesia. Elemental analysis has shown that the ore is rich in Ca and ...

International Nuclear Information System (INIS)

Lead is contained as trace element in uranium ores and propagates throughout the production process to intermediate products like yellow cake or uranium oxide. The lead isotopes in such material originate from two sources: natural lead and radiogenic lead. The variability of the isotopic composition of lead in ores and yellow cakes was studied and the applicability of this parameter for nuclear forensic investigations was investigated. Furthermore, the chemical impurities contained in these materials were measured in order to identify characteristic differences between materials from different mines. For the samples investigated, it could be shown, that the lead isotopic composition varies largely from mine to mine and it may be used as one of the parameters to distinguish between materials of different origins. Some of the chemical impurities show a similar pattern and support the conclusions drawn from the lead isotope data. (orig.)

International Nuclear Information System (INIS)

The design, construction and operation of a pilot plant are often important stages in the development of a project for the production of uranium concentrates. Since building and operating a pilot plant is very costly and may not always be required, it is important that such a plant be built only after several prerequisites have been met. The main purpose of this guidebook is to discuss the objectives of a pilot plant and its proper role in the overall project. Given the wide range of conditions under which a pilot plant may be designed and operated, it is not possible to provide specific details. Instead, this book discusses the rationale for a pilot plant and provides guidelines with suggested solutions for a variety of problems that may be encountered. This guidebook is part of a series of Technical Reports on uranium ore processing being prepared by the IAEA's Division of Nuclear Fuel Cycle and Waste Management. 42 refs, 7 figs, 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

The formation of textured YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (123) from a liquid phase according to the peritectic reaction Y{sub 2}BaCuO{sub 5} (211) + liquid {yields} 123 was analyzed using real-time analysis techniques of high-temperature X-ray diffraction, high-temperature optical microscopy, and environmental scanning electron microscopy (ESEM). Results were coupled with conventional ''post-mortem'' SEM analysis of processed samples at various stages of microstructural development. Observations of 123 formation and growth from the peritectic melt permit the conclusion that the presence of crystalline 211 primarily acts as a source of yttrium. The slow dissolution of 211 into the yttrium deficient liquid phase is the rate controlled step in the formation and growth of the textured 123, rather that its acting as a nucleation site for 123 grains as has been widely assumed. (orig.).

International Nuclear Information System (INIS)

Radioactive particles as well as x irradiation from an external source has been used in the treatment of rheumatoid arthritis, osteoarthritis, and ankylosing spondylitis. In order to clarify effects of ionizing irradiation on synovial cells, radioactive gold ("1"9"8Au) and yttrium ("9"0Y) were added to fibroblast cultures derived from human synovial membranes. Other cultures were irradiated by a Picker x-ray machine. Fibroblast growth and hyaluronic acid production were measured. Radioactive gold and yttrium particles induced a significant increase of hyaluronic acid synthesis rate (pg/cell/day) and inhibited fibroblast growth. Fibroblasts continued to overproduce hyaluronic acid and to show growth inhibition 3 weeks after irradiation with radioactive gold. Hydrocortisone inhibited hyaluronic acid overproduction induced by radioactive gold. Overproduction of hyaluronic acid induced by the x-ray machine was inhibited by hydrocortisone, ...

International Nuclear Information System (INIS)

There are two non-equivalent sites of yttrium in the lattice of Y_2SiO_5. Both of them may be occupied substitutionally by Er"3"+, resulting in a laser active material. We measured absorption spectra of Y_2SiO_5:Er"3"+ at several low temperatures and we studied its emission spectrum at 4.2 K following selective excitation of individual Stark components of the "4I_1_32/ to "4I_1_52/ transition by the light of a tunable colour centre laser. The results of these two experiments allow classification of the absorption and emission lines into two independent systems, thus yielding two energy level schemes 1 and 2. Moreover, simple crystal field calculations strongly suggest from which Y_2SiO_5 crystallographic site spectrum 1 arises, and from which one spectrum 2. (author)

Energy Technology Data Exchange (ETDEWEB)

This article describes the utilization of plastic wastes in a blast furnace. The plastic waste is a substitution for petroleum and coal as a raw material for synthesis gas production. The synthesis gas is the reducing agent in the blast furnace for the reduction of iron ores. You can find here an ecological and economical analysis of this process in comparison to the utilization of petroleum and coal. (SR)

International Nuclear Information System (INIS)

To the crushed ore leaching is applied. The resulting solid-liquid mixture is fed to a hydro-cyclon grading facility; here the superfine grain is separated before the concentrated mixture can be filtered or centrifuged. The grading is done in several steps. From the liquid, ultimately ridded of the solid, uranium compounds are precipitated and the yellow cake is obtained. (DG).

Wastenet

... In spring, the marshes are filled with the atmospheric calls of lapwings and redshanks, all breeding on one of the UK's ...Butley river and Ore estuary, Boyton Marshes attracts breeding wading birds in spring and ducks, geese and swans in winter. It's also ... The moorland landscape looks especially colourful in late summer, while spring is the perfect time to come and see migrant birds like redstarts,...Valley This is a delightful oak woodland to walk through - especially in spring and early summer when lots of migrating birds come to breed ...

Energy Technology Data Exchange (ETDEWEB)

Past and current development of coal utilization technology in the Japanese steel industry is reviewed and some projects currently under research and development briefly described. These include DIOS, an iron making process which directly utilizes both iron ore and coal without a sintering plant or a coke oven; and the development of a new generation coke oven. 15 figs.

International Nuclear Information System (INIS)

Proceeding from commercially available instruments, a simple measuring system has been established, which renders possible fast and simple discontinuous analysis of individual elements. This measuring system is described, giving some examples of utilization in nonferrous metallurgy (mining, ore dressing, metallurgical treatment), and specific details, such as error of measurement, ranges of measurement and limits of utilization. (author).

Energy Technology Data Exchange (ETDEWEB)

The authors present the emitter efficiency results for the thin film 25 percent Ho YAG (Yttrium Aluminum Garnet, Y3Al5O12) selective emitter from 1000 to 1700 K with a platinum substrate. Spectral emittance and emissive power measurements were made (1.2 less than lambda less than 3.2 microns) and used to calculate the radiative efficiency. The radiative efficiency and power density of rare earth doped selective emitters are strongly dependent on temperature and experimental results indicate an optimum temperature (1650 K for Ho YAG) for thermophotovoltaic (TPV) applications.

International Nuclear Information System (INIS)

The prospect for the recovery of rare earths from red mud, the bauxite tailings from the production of alumina is examined. The Jamaican red mud by far has the higher trace concentrations of lanthanum, cerium, neodymium, and yttrium. Scandium is also present. The dissolution of the rare earth is a major extraction problem because of the large volume of other materials. The recovery processes that have been proposed include the production of co-products such as iron, alumina, and titanium concentrates, with the rare earths going with the titanium. In this paper a critical examination of the possible processes are presented with the recommended research projects to be carried out.

Energy Technology Data Exchange (ETDEWEB)

Thin films of high temperature garnet materials such as yttrium aluminum garnet (YAG) doped with rare earths are currently being investigated as selective emitters. This paper presents a radiative transfer analysis of the thin film emitter. From this analysis the emitter efficiency and power density are calculated. Results based on measured extinction coefficients for erbium-YAG and holmium-YAG are presented. These results indicated that emitter efficiencies of 50 percent and power densities of several watts/sq cm are attainable at moderate temperatures (less than 1750 K).

Energy Technology Data Exchange (ETDEWEB)

A temperature gradient across a thick ({ge}.1mm) film selective emitter will produce a significant reduction in the spectral emittance from the no temperature gradient case. Thick film selective emitters of rare earth doped host materials such as yttrium-aluminum-garnet (YAG) are examples where temperature gradient effects are important. In this paper a model is developed for the spectral emittance assuming a linear temperature gradient across the film. Results of the model indicate that temperature gradients will result in reductions the order of 20{percent} or more in the spectral emittance. {copyright} {ital 1997 American Institute of Physics.}

International Nuclear Information System (INIS)

In one of the first uses of high Tc superconductors in an end-use product, Lake Shore Cryotronics and a Swiss lab have developed a liquid nitrogen level sensor using a high Tc thin film. The probe is manufactured using a seamless stainless steel tube with an yttrium-based zirconium oxide flame-sprayed on the tube. A plasma-sprayed superconductor compound is deposited on top of that. The probe is coated with a sealant that protects the superconducting film from the atmosphere. This manufacturing method has yielded an extremely durable product. Unaffected by ice formation and related mechanical problems, the superconducting level sensor can be kept in the dewar for long periods of time.

International Nuclear Information System (INIS)

A cylindrical coordinate mathematical model to calculate "2"2"2Rn flux and movement was developed considering "2"2"2Rn production, decay, and diffusion in a multilayered, porous, permeable matrix. Air movement, transporting radon through the media, satisfies Darcy's law and is influenced by the air (barometric) pressure applied at the surface. Two zones of porous material have been defined, one with a "2"2"2Rn production term (the uranium ore zone) and the other without this term to simulate shotcrete or concrete ground support. A provision is made to evaluate the effect of a pinhole in an otherwise impermeable sealant. Comparisons are made between field measurements and predicted values. Specific examples are given of "2"2"2Rn flux from a finite ore-body model versus steady and periodic changes in barometric pressure. Also examined are "2"2"2Rn losses through pinholes for cases of linearly varying and static barometric pressures. The results ...

Energy Technology Data Exchange (ETDEWEB)

Features particular to the technology of using a blast furnace for the recycling of plastic waste are reported, and the behavior of plastic waste injected into a blast furnace is described. The plastic waste is injected into the furnace borne on a 1200degC hot blast through the tuyere. The plastic is converted into a reducing gas in the furnace, and the gas on its way up in the furnace is utilized as a reducing agent in the iron ore reducing reaction. The process is described below. All kinds of plastic waste may be utilized in this fashion, with the exception of polyvinyl chloride. As for polyvinyl chloride, efforts are under way to develop a technology to recycle this plastic. The method using the blast furnace tolerates a wide range of impurities, and the plastic waste is only to be crushed and granulated before use in the furnace. Plastic waste coarsely granulated but not pulverized may be completely gasified when the blast furnace raceway function is utilized. ...

Energy Technology Data Exchange (ETDEWEB)

Previous laboratory tests of elastomer O-rings in coal liquefaction solvents conducted at L'Garde, Inc., indicated that certain ethylenepropylenediene monomer (EPDM) compounds provided the best performance when a backup ring was used to limit swelling. Before service testing in a pump at the Wilsonville, Alabama, Advanced Coal Liquefaction Research and Development Facility, tests of six selected elastomers in the appropriate Wilsonville-produced solvent were conducted at Oak Ridge National Laboratory (ORNL). The ORNL tests measured the elastomers' changes in cross section, weight, density, and relative flexibility. Although two perfluoroelastomers showed less degradation of most properties during these tests, it was decided to proceed with service testing of two EPDM elastomers because of their much lower cost. 5 refs., 14 figs., 7 tabs.

International Nuclear Information System (INIS)

Thorium-230, together with "2"3"8U and "2"2"6Ra, was determined (mainly by #gamma#-spectrometry) in samples from the waste piles at Borst and Jazbec in the vicinity of the former uranium mine at Zirovski vrh, Slovenia. Activity (and in the case of uranium, also mass) balances for these nuclides were constructed for the overall operation of the mine and yellow cake plant, using experimental data and known data on ore and uranium production, and nuclide emissions to the environment. All the "2"2"6Ra resulting from ore exploitation is presently contained in the Borst tailings pile. However, because of the very high content of "2"3"0Th in red mud deposited at Jazbec, where 60% of this nuclide is found, the majority of "2"2"6Ra will be found at the Jazbec pile in the future, due to its ingrowth from "2"3"0Th over the next few thousand years. (Author).

International Nuclear Information System (INIS)

In the present work, a rapid deposition anodic stripping voltammetry (ASV) for determination of uranium is presented. For this purpose, the uranyl hexacyanoferrate (K2UO2[Fe(CN)6]) is deposited electrochemically on a thin palladium-aluminum electrode (Pd-Al) from a UO22+ solution in the presence of K3Fe(CN)6. Then, the well stable (K2UO2[Fe(CN)6]) on the electrode was stripped by anodic differential pulse voltammetry for measuring the UO22+ ion concentration. The effect of operational parameters, including: concentration of K3Fe(CN)6, solution pH, deposition potential, and deposition time were studied. In optimum conditions, the calibration graph was linear in the concentration range 105-7 x 10-4 mol L-1 with a detection limit of 6.2 x 10-6 mol L-1. The influence of some concomitant ions in K2UO2[Fe(CN)6] formation was investigated. The proposed method was used for the rapid determination of uranium in some uranium mineral ores. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Visible smoke of exhaust gas from iron ore sintering plants spoil the scenery around the works. In this paper, the mechanism of formation of visible smoke is discussed by detailed analysis of the exhaust gas components and dust in the Oita No. 1 sintering plant. The main substance of visible smoke was mist condensing in the air during the cooling of exhaust gas that contained 0.1 ppm of sulfuric acid. Sulfuric acid is considered to raise the dew point and so facilitate mist condensation, and to lower the vaporization of visible mist containing sulfuric acid solution. Dust in the exhaust gas is also considered to act as nucleation sites for mist condensation. This proposed mechanism was confirmed by the test remixing SOx-rich gas with desulfurization gas in the Nagoya No. 3 sintering plant. Long trails of visible smoke were observed by remixing SOx-rich gas with exhaust gas. In conclusion, in order to make exhaust gas invisible, it is not sufficient to enhance the ...

International Nuclear Information System (INIS)

The main activities developed at 'Instituto de Energia Atomica' Sao Paulo, Brazil, on the recovery of uranium from ores, the purification of uranium and thorium raw concentrates and their transformation in nuclear grade compounds, are reviewed. The design and assemble of pilot facilities for ammonium diuranate (ADV) uranium tetrafluoride, uranium trioxide, uranium oxide microspheres, uranyl nitrate denitration, uranim hexafluoride and thorium compounds are discussed. The establishment of analytical procedures are emphasized.

Energy Technology Data Exchange (ETDEWEB)

Study of the rate of dissolution in simulated lung fluid of uranium from 3 different ore matrices and from refined uranium dioxide in an essentially all teflon extraction apparatus; the rate of dissolution of thorium from a nickel metal/2 percent thoria mixture; the effect of neutron irradiation of the studied materials upon the dissolution rates; and the adsorptions of the radioisotope tracers barium 133 (substitute for radium), lead 203 and thorium 234 upon the extraction system components.

Energy Technology Data Exchange (ETDEWEB)

This work deals with kinetic description of carbothermic reduction of iron oxides using microwaves as power source. Previous researches show that it is possible to conduct this kind of process successfully, but real kinetic comparisons between conventional and microwaves procedure have been presented partially. The aim of this work is to describe reduction kinetics, taking into account how the iron oxide is reduced by microwaves compared with conventional energy supply. In this study the authors used iron ore in pellet shape and dust. They found that both, pellet and dust reduction stops when it reaches approximately 40%, even at whole power.

International Nuclear Information System (INIS)

Smugglers, who make use of the Ukraine-Slovak border for their business, might be satisfied after last week. The Slovak government ordered the switching off of scanning equipment monitoring the movement of goods by train through the Matovce border line. The modern equipment was substituted by people, who aren't able to check freight cars as effectively as gadgets. Not only in Ukraine are they celebrating this success in corruption, who demanded the shut-off of the scanning equipment The bosses on the Slovak side are also rubbing their hands. As told to TREND by Margareta Grecova, spokeswoman for Cargo Slovakia, 90% of goods that cross through the border at Matovce are unloaded. The most frequently transported commodities are ore, coal, chemical and petroleum products. Smugglers put their consignments among iron ore and coal. They prefer goods with high consumer taxes. Besides alcohol, there are mainly cigarettes. These are put into boxes which ...

Energy Technology Data Exchange (ETDEWEB)

A monitoring campaign of polychlorinated dibenzo-p-dioxins and dibenzofurans, polyaromatic hydrocarbons (PAHs), and polychlorinated biphenyl was carried out in an Italian iron ore sintering plant by sampling the combustion gases at the electrostatic precipitator (ESP) outlet, at the Wetfine scrubber (WS) outlet, and by collecting the ESP dust. Few data are available on these micropollutants produced in iron ore sintering plants, particularly from Italian plants. This study investigates the PAH emission profiles and the removal efficiency of ESPs and WS. PAHs were determined at the stack, ESP outlet flue gases, and in ESP dust to characterize the emission profiles and the performance of the ESP and the WS for reducing PAH emission. The 11 PAHs monitored are listed in the Italian legislative decree 152/2006. The mean total PAH sum concentration in the stack flue gases is 3.96 {mu}g/N m{sup 3}, in ESP outlet flue gases is 9.73 {mu}g/N m{sup 3}, ...

Science.gov (United States)

The study of the intrinsic behavior of high transition temperature copper-oxide superconductors (HTSC) has proven to be challenging because of the extreme sensitivity of their transport properties on material quality. These compounds are characterized by a high degree of structural and electrical anisotropy, and a very short superconductive coherence length of the same order as the size of the crystalline unit cell (~5-30 A). As a result, microscopic defects such as oxygen vacancies, cationic disorder, and the presence of minute impurities have a significant effect on electrical transport in these materials. Therefore, much effort has been expended in synthesizing sizable samples that are homogeneous, well characterized, and emenable to the study of the anisotropic properties of the HTSC. We have demonstrated that thin films of HTSC compounds such as rm YBa_2Cu_3O_{7 -delta}, which is a 92 K superconductor, can be synthesized easily by a technique known as pulsed laser deposition, and ...

Science.gov (United States)

B-cell Chronic Lymphocytic Leukemia; Nodal Marginal Zone B-cell Lymphoma; Recurrent Adult Burkitt Lymphoma; Recurrent Adult Diffuse Large Cell Lymphoma; Recurrent Adult Diffuse Mixed Cell Lymphoma; Recurrent Adult Diffuse Small Cleaved Cell Lymphoma; Recurrent Adult Grade III Lymphomatoid Granulomatosis; Recurrent Adult Immunoblastic Large Cell Lymphoma; Recurrent Adult Lymphoblastic Lymphoma; Recurrent Grade 1 Follicular Lymphoma; Recurrent Grade 2 Follicular Lymphoma; Recurrent Grade 3 Follicular Lymphoma; Recurrent Mantle Cell Lymphoma; Recurrent Marginal Zone Lymphoma; Recurrent Small Lymphocytic Lymphoma; Splenic Marginal Zone Lymphoma; Waldenstrom Macroglobulinemia

Energy Technology Data Exchange (ETDEWEB)

Recent progress in yttrium-based oxide high-temperature superconductors has enabled the production of a large diameter bulk with a strong flux-pinning force. A combination of this superconductor and a permanent magnet makes it feasible to fabricate a noncontact, non-controlled superconducting magnetic bearing with a very small rotational loss, applicable to a flywheel energy storage system. A conceptual design of an 8 MWh flywheel energy storage system using the new bearing has been developed, based on measured data on a miniature bearing model, which proved to be potentially capable of achieving a high energy storage efficiency of 84 pc. A 100 W h-class experimental system was then built, which attained a high revolution rate of 17000 rpm, with a rotational loss of about 0.6 W. (authors). 2 refs., 7 figs., 3 tabs.

International Nuclear Information System (INIS)

With the assistance of mechanical activation, yttrium-stabilized #alpha#-SiAlON was prepared by combustion synthesis in air, instead of high-pressure N_2 atmosphere for the first time. The reaction activity of metallic particles was remarkably enhanced by mechanical activation, which conduced the reduction of grain size, increased the total surface area and formation of fresh surface. The formation of #alpha#-SiAlON by combustion synthesis in air was explained by a kinetically induced reaction mechanism, in which both initial formation of #alpha#-SiAlON and following avoidance of oxidation were fulfilled by the retardation of O_2 infiltration owing to the short reaction period and fast cooling rate.

British Library Electronic Table of Contents (United Kingdom)

Abstract Background and Purpose: During laser lithotripsy, working instruments are often in close proximity to the distal fiber tip and may be damaged accidentally or even intentionally. The aim of this study was to compare the amount of damage to a standard guidewire and the nitinol wires of endourologic retrieval baskets that were affected by three different clinically available laser systems. Materials and Methods: The impact of pulsed laser irradiation on a standard hydrophilic guidewire and a retrieval basket were investigated. One infrared (IR) laser system (holmium:yttrium-aluminum-garnet [Ho:YAG]: ????=???2100???nm) and two laser systems emitting light in the visible (VIS) spectral range (frequency-doubled double-pulse neodymium:YAG [FREDDY]: ????=???532???nm/1064???nm and flashl...

Energy Technology Data Exchange (ETDEWEB)

The authors examine the relationship of the structure and mechanical properties of similar alloys of tungsten with rhenium produced by the powder metallurgy method by sintering powders. Since the alloys were deformed by rolling, we examine the effect of the resultant anisotropy of the structure on the properties of the metal in various directions. The tests were conducted on an alloy of tungsten with 2 wt.% rhenium and, for comparison purposes, an alloy of tungsten with additions of oxides of yttrium and hafnium. The mechanical properties of the alloys, i.e., strength, cracking resistance, cold shortness temperature, were determined in the bend test. Structural examination was carried out using an optical microscope, electron scanning microscopy, and the method of transmission electron microscopy.

Energy Technology Data Exchange (ETDEWEB)

Cold deformation of YBa{sub 2}Cu{sub 3}O{sub 7-x}(phase 123, T{sub c} = 88.5-92 K) powders and strips causes partial decomposition of the 123 phase, a reduction in the degree of orthorhombicity of the structure up to almost complete degradation, and a decrease in T{sub c}. When they are deformed, yttrium high temperature superconductors acquire basal (001) (110) texture with high pole density (13-15 arbitrary units), low scattering angle ({+-} 6deg--7deg from the normal direction), and a weak preference for a, b or a + b in the rolling direction; traces of (139) orientations may also be found. This texture is known to be favourable for increasing j{sub k}. The combined effect of cold deformation and a carbon-containing binder leads, however, to a complete loss of superconductivity at 77 K or above. Depending on the regime of subsequent annealing, the following effects may be observed: degradation of the orthorhombic structure with a decrease in T{sub c}; ...

Energy Technology Data Exchange (ETDEWEB)

The current status and prospects for Japan`s economy and steel industry, forecast for demand and supply of coking coal, directions in steel making technology, and Japan`s expectations for Canadian coal are discussed. The PCI system, the Coal Moisture Control System (CMC) to increase coke density before it is fed into coke ovens, a feeder that allows use of lower quality coke on the outskirts of blast furnaces, the Direct Iron Ore Smelting (DIOS) Process, and the `Next Generation Coke Oven`, where coke is heated rapidly and coked at 700-800{degree}C are considered. By 2000, semi-soft coking coals are expected to account for over half of total coal consumption by Japanese steel mills.

Energy Technology Data Exchange (ETDEWEB)

A fusion reactor (such as NET/ITER) which breeds its own tritium fuel requires tritium recovery, purification and separation from the other isotopes. Cyclic adsorption processes are strong candidates for several of the processes involved: amongst other advantages, they promise a low tritium inventory. A good adsorbent for such processes must have high adsorption capacity, high selectivity and very low tritium retention after each cycle. Pure zeolite powder is shown to have an excellent combination of these three properties. However, in practice problems can arise from tritium which is not removed by reactivation. In this paper we show that tritium retention in zeolites can be caused either by water retained in the zeolite structure, which can be removed by ore rigorous activation, or by water tapped on binders in commercial pellets. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Presented are nomographs for calculating volume of bulk materials (e.g. coal, ores, sand, limestone) in conical or oblong piles formed by means of throwers and other mechanical transporting devices. The author explains that when a thrower is stationary, the pile formed resembles a cone and its projection on the ground is roughly circular. If thrower is moving, in general along a straight path, the final shape is more oblong, resulting from overlapping of separately formed cones. Slope of piles depends on the angle of repose which material makes with the horizontal when piled. This angle depends on such factors as internal friction of material stored, the throwing impact, fineness of grains, and moisture content. Volume is determined from the angle of repose and geometrical data on the area occupied by the pile.

International Nuclear Information System (INIS)

A set of 35 uranium ore and 10 yellow cake samples, collected worldwide from different mines and production sites, were analyzed for their impurity spectrum by ICP-MS. Pattern recognition techniques such as cluster analysis were applied to the data set in order to characterize samples with relation to their geographical origin. The results obtained show a clear relationship between samples taken from the same geological origin and constitute a satisfactory fingerprint for establishing the origin of the material. In addition to the impurity data, data on the isotopic composition of radiogenic lead is used to resolve ambiguity when impurity cluster analysis fails to deliver unambiguous origin data. (author)

British Library Electronic Table of Contents (United Kingdom)

Abstract The Jebel Ressas Pb-Zn deposits in North-Eastern Tunisia occur mainly as open-space fillings (lodes, tectonic breccia cements) in bioclastic limestones of the Upper Jurassic Ressas Formation and along the contact of this formation with Triassic rocks. The galena-sphalerite association and their alteration products (cerussite, hemimorphite, hydrozincite) are set within a calcite gangue. The Triassic rocks exhibit enrichments in trace metals, namely Pb, Co and Cd enrichment in clays and Pb, Zn, Cd, Co and Cr enrichment in carbonates, suggesting that the Triassic rocks have interacted with the ore-bearing fluids associated with the Jebel Ressas Pb-Zn deposits. The 18O content of calcite associated with the Pb-Zn mineralization suggests that it is likely to have precipitated from a fl...

International Nuclear Information System (INIS)

From their genesis by weathering and sedimentation, bauxites, the principal aluminium ores, contain appreciable amounts of uranium and thorium. High resolution gamma spectrometry with a high purity germanium detector was used for an analysis of four industrially used bauxites from Gondama, Sierra Leone; Boke, Guinea; Weipa, Queensland, Australia; Gove, Northern Territory, Australia. Significant differences in uranium to thorium ratios and in activities of the uranium and thorium daughters were observed for the four bauxites. It was found that the bauxite from Gondama, Sierra Leone has an activity of only 10% compared with the others. Red mud tailings from such a bauxite may well be used as an additive to bricks, which is now illegal for normal red mud from more active bauxites. (author).

International Nuclear Information System (INIS)

The risks from mining and processing of ores is reviewed on a generic basis with particular reference to some of the confusions which can arise due to lack of consistency or common logic in the use of exclusion, exemption and clearance. The difference in exclusion and exemption are challenged by comparing doses received in high background radiation areas and the doses received from a mining practice. The common principle of risk to the human species is not applied consistently. The differences between IAEA recommendations and local regulatory conditions are compared, and the use of exemption levels as clearance levels is considered. A case study on management of mine tailings is presented with special focus on the use of clearance levels. In all areas of review the interpretation of regulation is subject to confusion resulting from inconsistencies which can distort free market economics. (author).

British Library Electronic Table of Contents (United Kingdom)

The Jaduguda U (?Cu?Fe) deposit in the Singhbhum shear zone has been the most productive uranium deposit in India. Pyrite occurs as disseminated grains or in sulphide stringers and veins in the ore zone. Veins, both concordant and discordant to the pervasive foliation, are mineralogically either simple comprising pyrite ? chalcopyrite or complex comprising pyrite + chalcopyrite + pentlandite + millerite. Nickel-sulphide minerals, though fairly common in concordant veins, are very rare in the discordant veins. Pyrite in Ni-sulphide association is commonly replaced by pentlandite at the grain boundary or along micro-cracks. Based on concentrations of Co and Ni, pyrite is classified as: type-A ? high Co (up to 30800?ppm), no/low Ni; type-B ? moderate Co (up to 16500?ppm) and moderate to high ...

Energy Technology Data Exchange (ETDEWEB)

Since the 1950s a transport revolution has occurred comparable to events in the late nineteenth century when sailing ships were replaced by steam vessels. Freight rates for bulk products have decreased 65-70% due to improved maritime technology, and formerly separate markets for bulk products have been unified globally. It is suggested that the low freight rates since the early 1980s will level out in future. Price peaks caused by political and military crises like the Korean war, the Suez crisis, OPEC I and OPEC II also seem to be of diminishing importance over time. The world market has become much less sensitive to external shocks due to alternative sources of supply and alternative transport routes. Examples are given from the coal, grain and iron ore international market. 62 refs., 24 figs., 4 tabs.

British Library Electronic Table of Contents (United Kingdom)

Abstract Alcoa World Alumina Australia mines bauxite under lease agreements with the Government of Western Australia. The leases lie in the Darling Range to the east of Perth, the capital and major population center. In addition to bauxite and other mineral ores, the Darling Range is a major potable water source and harbors a species-rich forest dominated by Jarrah (Eucalyptus marginata), a significant commercial timber. Conservation and recreation are important land uses in the region. Social and political pressures have led to stringent governmental requirements for restoration. In addition, a summer drought period, a soil deficient in most nutrients, water management challenges, an introduced disease, caused by Phytophthora cinnamomi Rands, and a post-mining ecosystem that must be condu...

International Nuclear Information System (INIS)

Categorization is complete. Samples 11-3-1 (NSR-F-270409-01) and 11-3-2 (NSR-F-270409-02) are depleted uranium powders of moderate purity (#approx#65-80 % U). The uranium feed stocks for 11-3-1 and 11-3-2 have both experienced a neutron flux (as demonstrated by the presence of "2"3"2U). Sample 11-3-3 is indistinguishable from a natural uranium ore concentrate of moderate purity (#approx#70-80% U). Two anomalous objects (11-3-1-4 and 11-3-2-5) were found in the material during aliquoting. These objects might be valuable for route attribution.

International Nuclear Information System (INIS)

Production of Fe_2O_3, Y_2O_3, YFeO_3, Y_3Fe_5O_1_2 powders using the alkoxomethod - during hydrolysis by yttrium and iron alcohol solutions, is studied. It is stated that production of the powders of Y_2O_3-Fe_2O_3 system oxides using alkoxomethod permits to decrease essentially the reaction volumes, number of operations, their duration as compared to the cooxidation of oxide hydrates from inorganic salt aqueous solutions. During heat treatment of iron (3) alcohol hydrolysis products #gamma#-Fe_2O_3 is first crystallized by contrast to #alpha#-FeOOH, usually produced by deposition from solutions. Further heat treatment of #gamma#-Fe_2O_3 results in production of #alpha#-Fe_2O_3. Conditions for crystallization of Y_3Fe_5O_1_2 and YFeO_3 phases, prepared by both methods, and their crystallite mean sizes are close, but the powders obtained from alcohols are more homogeneous.

International Nuclear Information System (INIS)

Uranium-aluminum alloys with a significant enrichment of uranium with "2"3"3U or "2"3"5U serve as nuclear fuels in research reactors. The quality assurance of this fuel requires, among other things, precise knowledge that all trace metal constituents that affect neutron economy, fuel integrity, and fuel fabrication process parameters are well within the specification limits. Trace metal characterization of "2"3"5U-Al alloy has been carried out by atomic spectrometry. The trace metal constituents of interest are grouped into common metals (silver, boron, calcium, cadmium, cobalt, chromium, copper, iron, magnesium, manganese, molybdenum, sodium, nickel, lead, silicon, tin, titanium, vanadium, tungsten, and zinc) and lanthanides (cerium, dysprosium, europium, gadolinium, holminium, lutetium, samarium, and terbium). The elements yttrium and zirconium are grouped with the latter in view of the chemical separation procedure used. The alloy samples are dissolved in 6 M ...

International Nuclear Information System (INIS)

In this study nanocrystalline powders of yttria-stabilized zirconia (ZrO_2-8Y_2O_3) have been synthesized through 'polymerized complex method'. Zirconium chloride, yttrium nitrate, citric acid and ethylene glycol were polymerized at 80 "oC to produce a gel-like mass in which metallic ions were uniformly distributed. During the thermal treatment of dried gel, nanocrystalline powder was formed at 450 "oC and 650 "oC for 2 h. Thermal reactions and crystalline phase formation of the dried gel were investigated through thermal analysis and X-ray diffraction analysis, respectively. The results of thermal analysis and XRD showed the formation of nanocrystalline powder at less than 600 "oC. Chemical bonding of the dried gel was investigated by Fourier transform infrared spectroscopy analysis. Morphology of powder calcined at 650 "oC was analyzed by scanning electron microscope. Yttria-stabilized zirconia powders with the mean crystallite size of 6 nm were prepared ...

Energy Technology Data Exchange (ETDEWEB)

In this paper the authors present the first emitter efficiency results for the thin film 40 percent Er-1.5 percent Ho YAG (Yttrium Aluminum Garnet, Y3Al5O12) and 25 percent Ho YAG selective emitter at 1500 K with a platinum substrate. Spectral emittance and emissive power measurements were made (1.2 less than lambda less than 3.2 microns). Emitter efficiency and power density are significantly improved with the addition of multiple rare earth dopants. Predicted efficiency results are presented for an optimized (equal power density in the Er, (4)I[sub 15/2]-(4)I[sub 13/2] at 1.5 microns, and Ho, (5)I[sub 7]-(5)I[sub 8] at 2.0 micron emission bands) Er-Ho YAG thin film selective emitter.

International Nuclear Information System (INIS)

A technique for following sialon formation in situ by high temperature X-ray diffraction (HT-XRD) was developed. The composition chosen for study was an yttrium #alpha#-sialon with x=0.4. Powder compacts containing silicon nitride, aluminum nitride and yttria powders were pre-sintered at 1350 C and then studied by HT-XRD at temperatures between 1450 and 1580 C and nitrogen pressures of 0.11 MPa. The furnace was made from graphite coated with porous silicon nitride/silicon carbide. The coating prevented silicon carbide formation in the sample up to 1600 C. X-ray diffraction results show the formation of a Y_1_0Al_2Si_3O_1_8N_4 phase at 1350 C, which dissolved to form #alpha#-sialon and other phases at higher temperatures. The amounts of #alpha#-sialon formed are similar to the amounts reported by other authors. An empirical method was used for the calculation of activation energy for the silicon nitride to #alpha#-sialon transformation and resulted in a value of 330 ...

International Nuclear Information System (INIS)

We describe a panoramic stigmatic spectrograph comprising a grazing-incidence toroidal mirror and a large-aperture free-standing transmission diffraction grating (5000 lines mm-1 ). Two spectrograph versions were constructed, with grazing angles of 7.6 and 40 and the short-wavelength spectral limits near 4 and 1.5 nm. The spectrograph aberrations were studied by numerical ray tracing. The spectrograph was used to record line and quasi-continuous spectra (1.5 - 30 nm) of multiply charged ions in a plasma generated by the second-harmonic pulses of an yttrium aluminate laser (Q = 0.15 J, ? = 5 ns, ? = 0.54 ?m, repetition rate = 0.5 Hz). In combination with a laser-produced plasma radiation source, the arrangement was used to characterise soft x-ray optical components and to generate collimated beams of polarised radiation in the 14 - 20 nm range. (laser applications and other topics in quantum electronics)

Energy Technology Data Exchange (ETDEWEB)

The Formerly Utilized Sites Remedial Action Program (FUSRAP) of the Department of Energy is designed to identify and evaluate the radiological conditions at sites formerly used by the Corps of Engineers Manhattan Engineer District and the US Atomic Energy Commission. Where required, remedial action will be instituted to remove potential restrictions on the use of the sites due to residual low-level radioactive contamination. A total of 31 sites that may require remedial action has been identified. The purpose of the Ocean FUSRAP Program, which began in March 1981, is to assess the technical, environmental, and institutional feasibility of disposing, in the ocean and on the ocean floor, of FUSRAP soil and rubble which contains traces of natural radioactive materials. The initial focus has been on the Middlesex, New Jersey, Sampling Plant site and surrounding properties, which contain on the order of 100,000 metric tons of material. The Belgian Congo uranium ore and ...

Energy Technology Data Exchange (ETDEWEB)

This study investigated the influence of different charge typologies and additives on the PCDD/Fs amount produced and on the congener profiles in an iron ore sintering plant. Many tests were carried out combining different typologies of charge (iron materials) and solid fuel ('coke breeze' or 'anthracite') with or without the use of urea. The PCDD/Fs produced ranged from 1.2 to 22.7 {mu} g I-TEQ/ton of agglomerate, whereas the PCDD/Fs released to the ambient air ranged from 0.10 to 1.92 ng I-TEQ/Nm{sup 3} because of cleaning in an electrostatic precipitator (ESP) and a Wetfine scrubber (WS). A more homogeneous charge with a higher amount of fine particles charge appeared to produce a lower PCDD/Fs concentration due to a better combustion but this hypothesis needs further investigations on charges having different dimension particles. Only a synergitic action of urea and anthracite was able to reduce the high PCDD/Fs content due ...

Energy Technology Data Exchange (ETDEWEB)

Red mud, which is a pollutant residue from the extraction of alumina from bauxite ore, was utilized as an additive to a well blended mixture of three Egyptian clays, feldspar, quartz and grog. This was added in gradual proportions to study its effect on the vitrification properties of fired samples. Samples were moulded under a pressure of 20.7 MPa and fired at temperatures ranging from 950 C to 1100 C for soaking periods up to three hours. Compressive strength was determined as function of percent red mud added and firing temperature. A semi-exponential relation was established between strength and apparent porosity. 50 x 50 mm tiles containing 70% red mud addition and fired at 1100 C for one hour were tested. They were found to match the standards required for glazed wall tiles bodies. Tiles fired at 1100 C for 3 hours were compatible with the standards for glazed floor tiles. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Red mud is generated as a by-product in the production of Al(OH){sub 3}/Al{sub 2}O{sub 3} from bauxite ore. In this study the pellet-type adsorbents have been made from the red mud, and their adsorption capacities of heavy metal ions have been tested. The pellet-type adsorbents were synthesized to utilize the excellent adsorption capacity of the powder-type adsorbent for industrial application. The pellet-type adsorbents were prepared by mixing several kinds of additives with the red mud. It is found that the pellet-type adsorbent, made by sintering a mixture of red mud (96.0 wt%), polypropylene (2.5 wt%), fly ash (0.5 wt%), and sodium meta-silicate (1.0 wt%) at 1200 deg.C for 30 minutes, has the highest adsorption capacity. In this work, the two kinds of pellet-type adsorbents (bead-type, crushed-type) were prepared. The crushed-type adsorbent was found to show a better adsorption/desorption performance than the bead-type adsorbent. The crushed-type adsorbent ...

Energy Technology Data Exchange (ETDEWEB)

Activities of the Referenzlaboratorium Reinhaltung der Luft at Magdeburg as well as existing air pollution standards in the German Democratic Republic are reviewed. The laboratroy coordinates research and standardization in the field of industrial air pollution for the Ministry of Health. The standards provide orientation for emission control by state district health inspectorates. Emission limits (in g/m/sup 3/) which are international standards for 15 selected industries are listed. Emission limits (in g/m/sup 3/) of GDR standards, issued between 1971 and 1984 are also provided. They concern emission of brown coal dust from coal preparation plants, dust and chemical compound emission from metallurgical plants, dust emission from plants of the limestone and cement industry as well as from cupola furnace plants, boiler plants, plants of the wood industry and road asphalt mixing. Six additional standards which entered effect between 1984 and 1986 for metallurgy, ore ...

Energy Technology Data Exchange (ETDEWEB)

Researchers at Lawrence Livermore National Laboratory are developing high-performance explosive firing vessels to contain (one time) explosive detonations that contain toxic metals and hazardous gases. The filament-wound polymer composite vessels are designed to contain up to 80 lb (TNT equivalent) explosive in a 2-meter sphere without leakage. So far, two half-scale (1-meter diameter) vessels have been tested; one up to 150% of the design explosive limit. Peak dynamic pressures in excess of 280 MPa (40 Ksi) in the vessel were calculated and measured. Results indicated that there was a small amount of gas and particle leakage past the first two of the seven o-ring seals. However, the remaining five seals prevented any transient leakage of the toxic gases and particulates out of the vessel. These results were later confirmed by visual inspection and particulate analysis of swipes taken from the sealing surfaces.

Energy Technology Data Exchange (ETDEWEB)

The goal of this work was to develop a process flow diagram to economically produce a clean-burning fuel from fine Illinois coal. To accomplish this, the process of pelletizing fine coal with calcium hydroxide, a sulfur capturing sorbent, was investigated. Carbonation, which is the reaction of calcium hydroxide with carbon dioxide (in the presence of moisture) to produce a bonding matrix of calcium carbonate, was investigated as a method for improving pellet quality and reducing binder costs. Proper moisture level is critical to allow the reaction to occur. If too much moisture is present in a pellet, the pore spaces are filled and carbon dioxide must diffuse through the water to reach the calcium hydroxide and react. This severely slows or stops the reaction. The ideal situation is when there is just enough moisture to coat the calcium hydroxide allowing for the reaction to proceed. The process has been successfully demonstrated on a pilot-scale as a method of hardening iron ...

Energy Technology Data Exchange (ETDEWEB)

The Oklo natural fossil fission reactors in Gabon, Equatorial Africa, have been studied as a natural analogue for spent nuclear fuel in a geological environment. For these studies, it is important to know what has happened to these reactors since they formed. This review is focussed on existing geological and geochronological information concerning the Oklo reactors and the surrounding ore. A sequence of geological and geochemical events in the Oklo area, as described in the literature, is given. The data and the studies behind this established geochronology are discussed and evaluated. Of the regional geology, special attention is given to the dating of the Francevillian sediments, and the intrusion of a dolerite dyke swarm. The processes that led to the mineralisation at Oklo, the subsequent formation of the nuclear reactors and later migration of fission products are described. Further discussion concerns the studies of the dolerite dyke swarm, since this ...

Energy Technology Data Exchange (ETDEWEB)

The generation of acidic mine drainage is based on the oxidation dissolution of sulfide minerals due to the contact of ores with the natural water and the air. Namely, the sulfuric acid promotes the dissolution of sulfide minerals and gangue minerals, and Fe{sup 2+} is further oxidized to turn into Fe{sup 3+}, which acts as an oxidizer for other sulfide minerals and promotes the dissolution of the same. This paper roughly describes a mine drainage treatment focusing on an Fe{sup 2+} neutralization method and an iron bacteria oxidation method. The iron bacteria oxidation method is a method of oxidizing Fe{sup 2+} into Fe{sup 3+} by using iron bacteria, and then removing Fe{sup 3+} with calcium carbonate. This method has been used for treating the drainage in the Sakuhara Mine and the former Matsuo Mine, with good results. The paper finally introduces, as power-saving low-cost mine drainage treatment methods, a method of treating drainage containing Fe, Mn, Zn and Cd ...

Energy Technology Data Exchange (ETDEWEB)

The objectives of the project were (i) to develop a combination iron oxide production and carbon sequestration plant that will use serpentine ores as the source of iron and the extraction tailings as the storage element for CO2 disposal, (ii) the identification of locations within the US where this process may be implemented and (iii) to create a standardized process to characterize the serpentine deposits in terms of carbon disposal capacity and iron and steel production capacity. The first objective was not accomplished. The research failed to identify a technique to accelerate direct aqueous mineral carbonation, the limiting step in the integration of steel production and carbon sequestration. Objective (ii) was accomplished. It was found that the sequestration potential of the ultramafic resource surfaces in the US and Puerto Rico is approximately 4,647 Gt of CO2 or over 500 years of current US production of CO2. Lastly, a computer model was developed to ...

Energy Technology Data Exchange (ETDEWEB)

Ontario's Countdown Acid Rain program was formulated in 1985 and placed an annual SO{sub 2} emissions cap of 885 kilotonnes over the province from 1994. Caps were placed on emissions from the Inco nickel/copper smelter in Sudbury, the Falconbridge nickel/copper smelter in Sudbury, the Algoma iron ore sintering plant in Wawa, and Ontario Hydro fossil-fuel plants province-wide. Semi-annual reports are required of the companies, with the 6th report outlining the final planning phase and the 7th and later reports outlining implementation progress. This document summarizes the contents of the 7th set of reports and the responses of the government review team to each company's efforts. All companies have begun implementing abatement plans outlined in the final planning phase reports of December 1988 at a rapid pace and are generally on track in controlling emissions. However, all 4 company reports lack the necessary detail for a complete review of the ...

International Nuclear Information System (INIS)

An aerial radiological survey of the Oak Ridge Reservation (ORR) and surrounding area in Oak Ridge, Tennessee, was conducted during the period March 30 to April 14,1992. The purpose of the survey was to measure and document the terrestrial radiological environment of the Oak Ridge Reservation for use in environmental management programs and emergency response planning. The aerial survey was flown at an altitude of 150 feet (46 meters) along a series of parallel lines 250 feet (76 meters) apart and included X-10 (Oak Ridge National Laboratory), K-25 (former Gaseous Diffusion Plant), Y-12 (Weapons Production Plant), the Freels Bend Area and Oak Ridge Institute for Science and Education, the East Fork Poplar Creek (100-year floodplain extending from K-25 to Y-12), Elza Gate (former uranium ore storage site located in the city of Oak Ridge), Parcel A, the Clinch River (river banks extending from Melton Hill Dam to the city of Kingston), and the CSX Railroad Tracks ...

International Nuclear Information System (INIS)

We recently found that injection of 2 mCi of yttrium 90 (90Y; approximately 23,000 rads) into normal canine knees stimulated glycosaminoglycan (GAG) synthesis by femoral condylar cartilage. The present investigation was conducted to determine whether radiation affects cartilage metabolism directly. Rates of GAG synthesis and degradation in normal canine articular cartilage were studied following irradiation. Cultured synovium from the same knees was treated similarly, to determine the effects of irradiation on hyaluronic acid synthesis. Twenty-four hours after exposure to 1,000 rads, 10,000 rads, or 50,000 rads, 35S-GAG synthesis by the cartilage was 93%, 69%, and 37%, respectively, of that in control, nonirradiated cartilage. The effect was not rapidly reversible: 120 hours after exposure to 50,000 rads, GAG synthesis remained at only 28% of the control level. Autoradiography showed marked suppression of 35S uptake by chondrocytes after irradiation. Cartilage GAG ...

Energy Technology Data Exchange (ETDEWEB)

The processing characteristics, tensile properties, and oxidation response of two Nb-Ti-Al-Cr alloys were investigated. One creep tests at 650{degrees}C and 172 MPa was conducted on the base alloy which contained 40Nb-40-Ti-10Al-10Cr. A second alloy was modified with 0.11 at. % carbon and 0.07 at. % yttrium. Alloys were arc melted in a chamber backfilled with argon, drop cast into a water-cooled copper mold, and cold rolled to obtain a 0.8-mm sheet. The sheet was annealed at 1100{degrees}C for 0.5 h. Longitudinal tensile specimens and oxidation specimens were obtained for both the base alloy and the modified alloy. Tensile properties were obtained for the base alloy at room temperature, 400, 600, 700, 800, 900, and 1000{degrees}C, and for the modified alloy at room temperature, 400, 600, 700, and 800{degrees}C. Oxidation tests on the base alloy and modified alloy, as measured by weight change, were carried out at 600, 700, 800, and 900{degrees}C. Both the base ...

International Nuclear Information System (INIS)

?-Y(IO3)3 and ?-Y(IO3)3 are transparent until 12.8 and 13.4 ?m, respectively; thus they are interesting as a potential laser matrix in the mid- and beginning of the far-infrared. So, in order to investigate the properties of lanthanides- doped anhydrous yttrium iodate, polycrystalline samples of ?-Y1-xNdx(IO3)3 (0.01?x?0.05), ?-Y1-xNdx(IO3)3 (0.001?x?0.1), ?-Y1-xYbx(IO3)3 (0.01?x?0.33) and ?-Y1-xYbx(IO3)3 (0.01?x?0.25) were synthesized. For Nd3+ ions, fluorescent emissions from the 4F3/2 multiplet were observed at 300 K under pulsed laser excitations at 750 nm and for Yb3+, fluorescent emissions from the 2F5/2 multiplet were observed at 300 K under pulsed laser excitations at 980 nm. The decays of all these emissions were measured. They are exponential and the fluorescence lifetimes are in the range 0.093-0.193 ms for Nd3+ and 0.370-0.541 ms for Yb3+, depending on the nature of the host and the concentration of doping.

International Nuclear Information System (INIS)

In the present paper a procedure is proposed for the determination of traces of Cd, Co, Mn and Cr in petroleum industry produced water by inductively coupled plasma optical emission spectrometry. The procedure is based on cloud point extraction of these metals, as their dithizonate complexes, into the surfactant-rich phase of octylphenoxypolyethoxyethanol surfactant (Triton X-114). Extractions were carried out in solutions with salinities between 10 per mille and 70 per mille. Since residual salinity in the surfactant-rich phase caused differences in its transport to the plasma, yttrium was used as an internal standard to correct for this effect. The simultaneous metal extraction procedure was optimized by response surface methodology using a Doehlert design and desirability function. Enhancement factors of 21, 21, 9 and 19, along with limits of quantification of 0.093, 0.20, 0.73 and 1.2 #mu#g L"-"1, and precision expressed as relative standard deviation (n = 8, ...

International Nuclear Information System (INIS)

Different SiAlON composites based on #alpha#'-SiAlON are investigated, with respect to the phase relationships, densification behavior, and mechanical properties. The compositions are located on a phase-diagram line parallel to the Si_3N_4-Y_2O_3#centre dot#9AlN compound in the Si_3N_4-SiO_2-AlN-Al_2O_3-Y_2O_3-YN system. Analysis of the reaction sequences shows that the formation of the composites is associated with the transient appearance of Y_4Al_2O_9 (YAM), yttrium-aluminum-garnet (YAG), melilite, and a nitrogen-rich liquid phase. The small shift of compositions on the Si_3N_4-Y_2O_3#centre dot#9AlN compound phase-diagram line toward the Al_2O_3-rich side offers the advantage of a higher sinterability and the removal of the melilite phase from a wide range of compositions containing #alpha#'-SiAlON and polytypes. The #alpha#'/#beta#'-SiAlON composites show better mechanical properties in comparison to pure #alpha#'-SiAlON and composites of #alpha#'-SiAlON and ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents an overview of research conducted with the support of the Australian Institute of Nuclear Science and Engineering, at the University of Melbourne, School of Earth Sciences, Radiochemical Neutron Activation Laboratory. The primary objective of this research is to realize the high potential of the platinum group elements (PGE) and gold to the solution of petrogenetic problems, the study of magma generation and magmatic processes in mafic/ultramafic rock suites, as tracers in hydrothermal ore formation. The PGEs (Os, Ru, Ir, Pt, Pd and Rh) are among the least abundant of all elements on earth with unique properties such as high melting points, high electrical and thermal conductivity, high density, strength and toughness as alloys. They exhibit both siderophile and chalcophile characteristics and are valuable tools in providing information about magmatic processes, in particular S-saturation, as well as crystal fractionation trends. Two distinct ...

Energy Technology Data Exchange (ETDEWEB)

A study tour in autumn 1999, which was undertaken following the award of the Helmuth Burkhardt prize of Wirtschaftsvereinigung Bergbau e.V. to the authors, comprised visits to potash, molybdenum, lead, zinc, copper ore and coal mines in the mid-west of the USA. The Black Mesa Mine and Kayenta Mine of Peabody Western Coal Company in the Navajo Reserve in the north of Arizona, the Trapper Mine Inc. near Craig and the Twentymile Coal Company near Steamboat Springs, Colorado are described in this report. In addition to a brief description of the geology the coal winning is considered in greater detail. The Twentymile Coal Company was asked to explain the reasons for the successful operation of the colliery, which produces more than 5 mill. t anthracite per year by long wall working. (orig.) [German] Eine Exkursion im Herbst 1999, die durch die Verleihung des Helmuth-Burkhard-Preises der Wirtschaftsvereinigung Bergbau e.V. an Bergassessor Andreas Tschauder zustande kam, ...

Energy Technology Data Exchange (ETDEWEB)

The generation of industrial solid wastes containing leachable species of environmental concern is a problem for developing and developed nations alike. These materials arise from direct processing of mineral ores, from production of metals and minerals, from manufacturing operations, and from air and water pollution treatment processes. The general characteristics that make these wastes intractable is that their content of hazardous species is not easily liberated from the waste yet is not bound so tightly that they are safe for landfill disposal or industrial use. The approach taken in this work is a thermal treatment that separates the inorganic contaminants from the wastes. The objective is to provide recovery and reuse of both the residual solids and liberated contaminants. The results from operating this technique using two very different types of waste are described. The reasons that the process will work for a wide variety of wastes are explored. By using ...

Energy Technology Data Exchange (ETDEWEB)

A process is described for making a compound selected from a crystalline spinel of the formula A/sup II/V/sub 2-x//sup III/C/sub x//sup III/O/sub 4/ formula (1) or a crystalline perovskite of the formula D/sup III/V/sub 1-y//sup III/C/sub y//sup III/O/sub 3/ formula (2) from a pentavalent vanadium compound, where A is one or more of Mg, Zn, Mn, Fe, Co, Ni, Cu and Cd; D is one ore more of Y, the rare earths and Bi; C is one or more of Al, Ga, Cr, Fe and Co, x is zero to <2, and y is zero to<1. The process comprises (1) reducing a pentavalent vanadium oxidic compound to substantially the V/sup III/ state by heating at 100/sup 0/C. or less an aqueous medium slurry or solution of the pentavalent compound containing a reducing agent selected from hydrazine and a hydrocarbylhydrazine, (2) providing in the aqueous medium either before, during or after the reducing step, A/sup II/, D/sup III/ and C/sup III/ cations in solution in the ratio called for by the selected ...

Energy Technology Data Exchange (ETDEWEB)

Using Gammasphere data on prompt gamma rays from spontaneous fission of 252Cf, we propose energy-level schemes for 110,111,112, & 113Rh (Z=45). The fission-gamma data complement earlier studies of others on beta decay of fission products in that prompt fission gammas mainly populate yrast or near-yrast levels, while beta decay populates lower-spin levels. For the odd-A rhodium nuclei studied here, their ground bands and collective sidebands are compared with model calculations using triaxial-shaped nucleus with one odd quasi-proton. The energies and E2 transition rates are best fit by a shape slightly to the prolate side of maximum triaxiality, namely, gamma = 28 deg. The model calculations also show a K=1/2+ band with energies not in good agreement with a corresponding experimental band. The experimental 1/2+ band is regarded as an intruder band from a prolate-driving proton orbital 1/2[431] above the Z=50 closed shell. This intruder band, seen in other odd-A Rh isotopes, is ...

Energy Technology Data Exchange (ETDEWEB)

High angle conveyor systems in open pit mining offer many advantages over the traditional, truck only, haulage systems, including: (1) superior energy efficiency (2) less dependency on petroleum products (3) less sensitivity to inflation (4) less labour (5) less excavation for the amount of ore recovered, and (6) less ramp construction and maintenance costs. This paper presents the sandwich belt high angle conveyor as the vital link to optimisation of inpit conveying systems. High angle conveyor development to date is discussed, beginning with studies in 1979, to the first large scale prototype in 1983, through the numerous commercial installations. Discussion continues with the high angle conveyor systems to suit the various open pit mining operations and the corresponding characteristics of the system components, particularly the high angle conveyor. The range of high angle conveyor systems from the low capacity (up to 1 814 t/h), low lift (10.7 to 36.6 m), ...

Energy Technology Data Exchange (ETDEWEB)

Firstly, pitting corrosion observed on hold frames in cargo holds of bulk carriers which exclusively carry coal and iron ore has been investigated in detail. It was shown that the shape of the corrosion pits observed on them is a circular cone and the ratio of the diameter to the depth is in the range between 8 to 1 and 10 to 1, which is different from the trend observed for the bottom shell of the oil tanker where the ratio is in the range between 4 to 1 and 6 to 1. Secondly, a series of tensile tests has been conducted to investigate the effect of pitting corrosion on tensile strength of members. It was pointed out that the tensile strength decreases gradually and the total elongation decreases drastically with the increase of the thickness loss due to pitting corrosion. The reduction of the tensile strength of the members with pitting corrosion is larger than that of members with uniform thickness loss in terms of average thickness loss. Thirdly, a series of ...

Energy Technology Data Exchange (ETDEWEB)

The quantitative determination of oxide concentration by laser-induced breakdown spectroscopy is relevant in various fields of applications (e.g.: analysis of ores, concrete, slag). Calibration free laser-induced breakdown spectroscopy and the multivariate calibration are among the methods employed for quantitative concentration analysis of complex materials. We measured the intensity of neutral and ionized atomic emission lines of oxide materials by laser-induced breakdown spectroscopy and we modified the calibration free laser-induced breakdown spectroscopy method to increase the accuracy. The concentration of oxides was obtained by using stoichiometric relations. Sample materials were prepared from oxide powder (Fe{sub 2}O{sub 3}, MgO, CaO) by mixing and pressing. The concentration was 9.8-33.3 wt.% Fe{sub 2}O{sub 3}, 7.6-33.3 wt.% MgO and 33.3-81.2 wt.% CaO for different samples. Nd:YAG laser (wavelength 1064 nm, pulse duration {approx} 6 ns) ablation was ...

Energy Technology Data Exchange (ETDEWEB)

Proton induced X-ray and {gamma}-ray emission (PIXE/PIGE) have been used to analyze major and trace elements in a suite of 140 core samples from around of the Jim`s Find South gold anomaly in the Tanami desert, located in heavily weathered terrain. Simultaneous analyses were obtained for 30 elements, ranging in atomic number from {sup 3}Li to {sup 90}Th. The method was chosen because of its speed and the wide range of determination, its flexibility, precision and low detection limits. The regolith powder samples were treated by hot aqua regia before making them into pills. The PIXE/PIGE data of the acid insoluble residue give three factor analysis clusters. The first cluster comprises the elements F, Al, K, V, Mn, Fe, Ga, Rb, W and Au and is essentially related to sericitic wallrock alteration. The second cluster consists of Ti, As, Y, Zr, and Nb and is largely related to resistant minerals. The third cluster consists of Na, Ca and Sr and is interpreted to comprise elements in ...

International Nuclear Information System (INIS)

Presently, industrial maturity can be claimed for two fuel cycle strategies, viz. the 'Once Through Fuel Cycle' (OTC), and the 'Reprocessing Fuel Cycle' (RFC) in which plutonium and very limited uranium quantities are being recycled. It is helpful to recall some key data that set the stage for any discussion of fuel cycle options: 1. Worldwide, the annual spent fuel discharge is in the range of 10500-11000 t heavy-metal (HM), while the industrial reprocessing capacity amounts to #approx# 5000 t HM (OECD NUCLEAR ENERGY AGENCY, Accelerator-driven Systems (ADS) and Fast Reactors (FR) in Advanced Nuclear Fuel Cycles: a Comparative Study, Paris, 2002). Hence, less than 1/2 of the discharged spent fuel can be processed. 2. Worldwide, the cumulative inventory of stored spent fuel is estimated to be #approx# 190000 t HM, and the amount of reprocessed spent fuel is estimated to be #approx# 70000 t HM. The latter inventory has been transformed into high-level waste (HLW) and spent light water ...

Energy Technology Data Exchange (ETDEWEB)

Many mines and processing facilities are in remote, difficult to access areas, or are in areas where access is limited or restricted for national reasons. In a joint project with Canada Centre for Remote Sensing, the Canadian Safeguards Support Program is investigating utility of multi- and hyperspectral remote sensing for remotely inspecting such site. With a view to eventually using the hyperspectral satellite data now coming available, airborne data over uranium and copper mine tailings and uranium processing facilities in northern Canada were acquired. The objective of this work is to demonstrate that multispectral and hyperspectral data can provide complementary and supplementary information to high-resolution panchromatic imagery for the following safeguards applications: Inspection aids (up-to-date maps of remote locations), change detection, evaluation of member state declarations, monitoring of reactor, mining and processing facility operations, and detection of undeclared ...

International Nuclear Information System (INIS)

The improving uranium extraction efficiency of yellow cake production from shale deposit by acid pugging and curing with D263B resin adsorption is described in this paper. The analysis and examination show that the composition of uranium minerals in one of uranium ores is very complex, which directly influence the extraction efficiency of uranium and processing technology. Conventional experimental results indicate that uranium leaching efficiency is changed between 50?60% by conventional agitation method. In this case, acid pugging and curing experiments are employed in order to improving the extraction efficiency. A series of acid pugging and curing experiments are carried out to get parameters for heap leaching in pilot plant experiment. The experiment results by acid pugging and curing technology showed that uranium leaching efficiency can reach to 90% of extraction efficiency mixed with 1% manganese dioxide, 12% sulfuric acid pugging, curing 3 days and leached ...

Energy Technology Data Exchange (ETDEWEB)

Acute thoracic aortic injuries account for up to 10-20% of fatalities in high-speed deceleration road accidents and have an estimated immediate fatality rate of 80-90%. Untreated survivors to acute trauma (10-20%) have a dismal prognosis: 30% of them die within 6 hours, 40-50% die within 24 hours, and 90% within 4 months. It was investigated the diagnostic accuracy of Helical Computed Tomography (Helical CT) in acute traumatic injuries of the thoracic aorta, and the role of this technique in the diagnostic management of trauma patients with a strong suspicion of aortic rupture. It was compared retrospectively the chest Helical CT findings of 256 trauma patients examined June 1995 through August 1999. Chest Helical CT examinations were performed according to trauma score, to associated traumatic lesions and to plain chest radiographic findings. All the examinations were performed with no intravenous contrast agent administration and the pitch 2 technique. After a previous baseline ...