International Nuclear Information System (INIS)

ZrO_2/O'-sialon composites were obtained via reaction sintering of ZrSiO_4 and Si_3N_4 powders at about 1700 deg C. Y_2O_3 was effective in both stabilizing of zirconia and densifying the composites. However, it is not easy to select an optimum value of the single additive to balance these two requirements simultaneously. With low Y_2O_3 addition, some tetragonal zirconia grains in the sintered samples are transformable during mechanical grinding but the full densification of the material is then sacrificed. On the other hand, addition more Y_2O_3 to achieve complete densification results in the zirconia being stabilized into undesirable t' or cubic forms. Therefore no improved toughening effects have been achieved in the composites. Heat-treatment of the materials at 1400 deg C. results in the diffusion of yttria from the grain boundary phase to zirconia and ...

International Nuclear Information System (INIS)

Zirconia has demonstrated a very moderate toughening effect in nitrogen-based ceramic composites because the reaction between tetragonal zirconia (t-ZrO_2) and nitrogen results in additional zirconia stabilization to a nontransformable t' or cubic structure. In O'-SiAlON matrices, the oxygen concentration increases and the oxygen-rich intergranular glassy phase prevents zirconia from nitridation. As a result, tetragonal ZrO_2 is maintained and is transformable in the O'-SiAlON materials. The present study has provided transmission electron microscopy (TEM) evidence of the zirconia transformation and the associated toughening effect in a ZrO_2/O'-SiAlON composite. The implications and limitations of the transformation on toughening of the material are discussed.

International Nuclear Information System (INIS)

Mixed additions of Sm_2O_3 and Y_2O_3 were used in the formation of zirconia-containing O'-sialon composites, where Sm_2O_3 was used for the purpose of densification and Y_2O_3 for zirconia stabilization. Dense ZrO_2/O' -sialon composites were produced at 1500 deg C. by sintering in nitrogen for 4 hours. Tetragonal zirconia remained in the product and t#->#m transformation was observed when the sample was ground into powder. However, the improvement in fracture toughness was not significant and this was attributed to the weakened transformability of the tetragonal zirconia phase in the nitrogen-based materials. 18 refs., 4 tabs., 2 figs.

British Library Electronic Table of Contents (United Kingdom)

Objectives: The aim of this study was to evaluate the in vitro behaviour of all-ceramic zirconia molar crowns in regard to different core designs and marginal fit. Methods: Identically shaped methacrylate molars were prepared according to the ceramic restoration directives resulting in a 1-mm deep circular shoulder preparation. They were embedded in polymethylmethacrylate resin after covering their roots with a polyether layer to simulate periodontal mobility. The crown cores were made of yttria-stabilized zirconia veneered with a corresponding veneering ceramic. The crowns were divided into 5 groups (n=8) which differed in core design and cement gap thickness: #1: simple core, 40mm cement; #2: core with minimal occlusal support, 40mm cement; #3: core with optimized cusp support, 40mm ceme...

International Nuclear Information System (INIS)

Highly conductive biaxially textured RuO_2 thin films were deposited on technically important SiO_2/Si substrates by pulsed laser deposition, where yttria-stabilized zirconia (YSZ) produced by ion-beam-assisted-deposition (IBAD) was used as a template to enhance the biaxial texture of RuO_2 on SiO_2/Si. The biaxially oriented RuO_2 had a room-temperature resistivity of 37 #mu##OMEGA#-cm and residual resistivity ratio above 2. We then deposited Ba_0_._5Sr_0_._5TiO_3 thin films on RuO_2/IBAD-YSZ/SiO_2/Si. The Ba_0_._5Sr_0_._5TiO_3 had a pure (111) orientation normal to the substrate surface and a dielectric constant above 360 at 100 kHz. copyright 1998 Materials Research Society.

Energy Technology Data Exchange (ETDEWEB)

The authors report the fabrication and characterization of a low temperature (200--400 C) thin film gas sensor constructed from a MOCVD-grown yttria-stabilized zirconia (YSZ) layer sandwiched between two platinum thin film electrodes. A reproducible gas-sensing response is produced by applying a cyclic voltage which generates voltammograms with gas-specific current peaks and shapes. Growth conditions are optimized for preparing YSZ films having dense microstructures, low leakage currents, and maximum ion conductivities. In particular, the effect of growth temperature on film morphology and texture is discussed and related to the electrical and gas-sensing properties of the thin film sensor device.

Energy Technology Data Exchange (ETDEWEB)

In order to apply chemical-looping combustion to a practical power plant, carbon deposition on the solid particle is one of the key problems to be overcome. Six kinds of solid particles were examined to clarify the kinetic behavior of carbon deposition. The effects of the solid composition, feed gas composition, and reaction temperature on carbon deposition were investigated by thermogravimetrical reactor on the basis of NiO/YSZ particle. From the viewpoints of both reactivity and resistance against carbon deposition, the particle of NiO mixed with YSZ (i.e., yttria-stabilized zirconia) was found to be a good candidate for chemical-looping combustion. It has been observed that carbon deposition could be completely avoided with very low concentration of water vapor. By means of a proposed model, the condition that carbon deposition would be avoided was identified. 12 refs., 8 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

The project has been developing Yttria Stabilized Zirconia (YSZ)-Alumina Composites as an electrolyte of a self-support type planar Solid Oxide Fuel Cell (SOFC) from the following points of view: a path of alumina particles with high thermal conductivity can be designed as an electrolyte sheet; there are some possibilities that the electrolyte can be enhanced in mechanical strength. As previously reported, these composite materials have higher mechanical strength and better thermal shock resistance than those of YSZ. These composites containing 0-30 wt% of Al[sub 2]O[sub 3] were measured by AC impedance method at temperatures of 250-1,000[degree]C. Electrical conductivities of 8YSZ without Al[sub 2]O[sub 3] and a composite consisting of 80 wt% YSZ and 20 wt%Al[sub 2]O[sub 3] as sintered samples were 1.2 x 10[sup -1]S/cm and 1.0 x 10[sup -1]S/cm respectively at 1,000[degree]C. The composite containing 20 wt% of Al[sub 2]O[sub 3] is the most ...

Energy Technology Data Exchange (ETDEWEB)

The contaminants that are potentially present in the coal-derived gas stream and their thermochemical nature are discussed. Accelerated testing was carried out on Ni-YSZ/YSZ/LSM solid oxide fuel cells (YSZ: yttria stabilized zirconia and LSM: lanthanum strontium manganese oxide) for eight main kind of contaminants: CH{sub 3}Cl, HCl, As, P, Zn, Hg, Cd and Sb at the temperature range of 750-850 C. The As and P species, at 10 and 35 ppm, respectively, resulted in severe power density degradation at temperatures 800 C and below. SEM and EDX analysis indicated that As attacked the Ni region of the anode surface and the Ni current collector, caused the break of the current collector and the eventual cell failure at 800 C. The phosphorous containing species were found in the bulk of the anode, they were segregated and formed ''grain boundary'' like phases separating large Ni patches. These species are presumably ...

Energy Technology Data Exchange (ETDEWEB)

BaTiO{sub 3} compacts, when fluxed with {lt} 2 vol% of a complex borate glass phase, were sintered to near theoretical density at temperatures {lt} 1175{degrees}C in 2 h. Microstructural analysis showed a uniform grain size {lt} 1.0 {mu}m with 0.75 wt% ZrO{sub 2} added to the flux phase as a grain growth inhibitor. TEM analysis revealed a microcrystalline grain-boundary phase with the ZrO{sub 2} resident along the grain boundaries. These samples displayed an essentially flat dielectric profile, low dissipation factors ({lt} 2%) over the range 25{degrees} to 125{degrees}C, a near linear dependence ({approx} {+-} 15%) between 25{degrees} and {minus} 55{degrees}C, and significantly increased voltage stability. X-ray diffraction analysis of these small-grained materials indicates a suppression of the tetragonal structure toward a more cubic modification.

Energy Technology Data Exchange (ETDEWEB)

Damage and cyclic fatigue failure under alternating loading in transformation-toughened zirconia ceramics is reviewed and compared to corresponding behavior under quasi-static loading (static fatigue). Current understanding of the role of transformation toughening in influencing cyclic fatigue-crack propagation behavior is examined based on studies which altered the extent of the tetragonal-to-monoclinic phase transformation in MG-PSZ through subeutectoid aging. These studies suggest that near-tip computations of the crack-driving force (in terms of the local stress intensity) can be used to predict crack-growth behavior under constant amplitude and variable-amplitude (spectrum) loading, using spatially resolved Raman spectroscopy to measure the extent of the transformation zones. In addition, results are reviewed which rationalize distinctions between the crack-growth behavior of preexisting, long'' (> 2 mm), ...

International Nuclear Information System (INIS)

In this paper the effect of adding commercially pure yttria concentrate and yttrium carbonate concentrate (NUCLEMON) on the densification of #beta#-Sialon has been studied. The specimens were sintered in graphite furnace at 1720 and 175 deg C, for 1 hour in a nitrogen atmosphere. Densities of up to 99% of the theoretical density were obtained. Microstructural analyses of the specimens were carried out with the aid of an X ray diffractometer and a scanning electron microscope. (author)

UK PubMed Central (United Kingdom)

BackgroundThe successful use of zirconia ceramics in orthopedic surgery led to a demand for dental zirconium-based implant systems. Because of its excellent biomechanical characteristics,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

NO{sub x} compounds, specifically NO and NO{sub 2}, are pollutants and potent greenhouse gases. Compact and inexpensive NO{sub x} sensors are necessary in the next generation of diesel (CIDI) automobiles to meet government emission requirements and enable the more rapid introduction of more efficient, higher fuel economy CIDI vehicles. Because the need for a NO{sub x} sensor is recent and the performance requirements are extremely challenging, most are still in the development phase. Currently, there is only one type of NO{sub x} sensor that is sold commercially, and it seems unlikely to meet more stringent future emission requirements. Automotive exhaust sensor development has focused on solid-state electrochemical technology, which has proven to be robust for in-situ operation in harsh, high-temperature environments (e.g., the oxygen stoichiometric sensor). Solid-state sensors typically rely on yttria-stabilized zirconia (YSZ) as the ...

UK PubMed Central (United Kingdom)

BackgroundTitanium and titanium alloys are widely used for fabrication of dental implants. Since the material composition and the surface topography of a biomaterial play a fundamental...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundOsseointegration is crucial for the long-term success of dental implants and depends on the tissue reaction at the tissue-implant interface. Mechanical properties and biocompatibility...Full Text Available

Science.gov (United States)

"Precision manufacture of ceramic parts with CNC machining capability for aerospace, lasers, semiconductors and other industries. Materials include alumina, zirconia, glass, ferrites, silicon carbide, silicon nitride, sapphire, cordierite, mullite and others. A.C.T. has seen the number of applications and demand for high-realiability ceramics (aluminum oxide, zirconia, glass, ferrites, silicon carbide, silicon nitride, sapphire, cordierite, mullite, etc...) increase continually within the aerospace, computer and the industrial markets."

International Nuclear Information System (INIS)

Synthesis of O'/#beta#' SiAlON composites was studied. As starting materials, Si_3N_4, Al_2O_3 and SiO_2 powders were used. Pressureless sintering was applied as consolidation technique and was performed at 1400-1700 C. Densification and reaction taking place during sintering were followed. Microstructure of O'/#beta#' composites is discussed. It was found that without additives liquid phase amount formed within the samples was below critically needed for full densification, but promoted reaction of O' and #beta#' formation. Using yttria as additive densification was enhanced. O'/#beta#' ratio decreased while H_V and K_I_c increased with increasing amount of additive. (orig.).

International Nuclear Information System (INIS)

Magnetic structures and magnetocrystalline anisotropy (MCA) of tetragonal phase Fe_3Pt with an L1_2 atomic ordering in bulk and thin film are investigated by means of the first-principles full-potential linearized augmented plane-wave method. The results obtained predict that the tetragonal phase, in which the tetragonal distortion with (c/a) = 0.95 makes an asymmetry of magnetic properties along the c-axis (out-of-plane) and a-axis (in-plane), has an out-of-plane MCA. In addition, from the thin film calculations, the presence of surface is found to strongly enhance the out-of-plane MCA.

International Nuclear Information System (INIS)

Liquid radioactive raffinates from nuclear fuel reprocessing at the Idaho National Engineering and Environmental Laboratory were solidified, or calcines, in a fluidized bed reactor at approximately 500 C to form a dry granular material. This calcine has been provisionally stored near-surface in concrete-encased stainless steel bins at the Idaho Nuclear Technology Engineering Center. Research addressing the permanent immobilization of radioactive waste has been ongoing. One option is to separate the radioactive constituents from the calcine, thereby reducing the radioactive waste volume to be ultimately stored at a national nuclear waste repository. Nitric acid dissolution of the calcine is a key front-end unit operation in the separations option. In order to design calcine dissolution equipment, quantification of dissolution reaction rate parameters is required. A pilot-plant-produced, non-radioactive calcine was utilized to study the dissolution kinetics of a ...

International Nuclear Information System (INIS)

The cubic-tetragonal lattice transformation in A-15 compounds is described by an empirical model in which the density of states function near the Fermi energy is characterized by a two-parametric peak in addition to the constant part. Two types of peak splitting under tetragonal deformation are considered, leading to qualitatively different results about the phase transition. Results are given for the order parameter, the phase stability, the soft elastic modulus, and the paramagnetic spin susceptibility. Comparing with measurements of the magnetic susceptibility of V_3Si single crystals near the phase transition a better agreement is obtained for a twofold degenerate density of states peak than for a threefold degenerate one. (author).

International Nuclear Information System (INIS)

Large, complex, high purity ceramic shapes are required by a variety of emerging technologies for their electrical insulation and high temperature strength properties coupled with their refractoriness and purity. Ceramic sealant bonding, using crystalline and vitreous sealant materials, has recently shown significant potential for joining technical ceramics to form the required shapes. Materials and techniques for joining technical ceramics including alumina, magnesia, zirconia and thoria are discussed. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Mechanical alloying is an important pre-requisite for the manufacturing of heat resistant oxide-dispersion-strengthened superalloys. Though the microstructure of these materials after hot extrusion and recrystallization treatment is well documented, little is known about the microstructural evolution during ball-milling. A method was tested to prepare electron transparent foils and extraction replica from powder particles for TEM investigations. The microstructure was found to consist of a Ni-Cr-Al solid solution in which submicron particles of refractory metals were embedded. The extremely fine grainize of about 50 nm is the consequence of severe plastic deformation. Yttria particles could not be detected in the powder after ball milling, but after a heat treatment at 1000 C the well-known fine dispersion of oxide particles was evident. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Fine ceramic particles of zirconia toughened alumina (ZTA), titania toughened alumina (TTA), and zirconia-titania toughened alumina (ZTTA) have been synthesized by ultrasonic spray pyrolysis (USP) at various temperatures from starting salt solutions of various compositions aiming for the development of catalytic material. These particles were characterized for properties such as shape, size and size distribution, diffraction pattern, and chemical and phase composition of elements by scanning electron microscopy (SEM), particle size analyzer (PSA), x-ray diffraction (XRD), and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Chemical compositions and sizes of ceramic composites have been controlled by the stoichiometry of salt solutions and the flow rate of spraying solutions. The optimum experimental conditions for the various composite particle synthesis have been proposed.

Energy Technology Data Exchange (ETDEWEB)

Three dispersants (stearic acid, oleic acid, and poly-(12-hydroxystearic acid)) are compared for their ability to produce low-viscosity suspensions of zirconia in kerosene. Rheological measurements and sediment packing density measurements show that poly(12-hydroxystearic acid) is a better dispersant than stearic acid or oleic acid; this is explained in terms of the longer tail of the poly-(12-hydroxystearic acid) surfactant molecule. The amount of dispersant can be optimized to reduce viscosity and yield point of the suspension, and to eliminate thixotropic hysteresis. The use of a dispersion medium of lower viscosity than the dispersant makes it easy to detect when complete monolayer coverage has been achieved. The loss of pseudoplasticity, brought about by a higher degree of deflocculation, can be recovered by increasing the volume fraction of solids of a suspension and this is beneficial in the plastic forming of ceramics. Rheological measurements showed that ...

International Nuclear Information System (INIS)

A study has been made of the precipitation and growth processes which occur during cooling from solution treatment and under isothermal hold conditions in a magnesia-partially-stabilized zirconia alloy. Three types of precipitate have been identified which develop during cooling or during isothermal hold treatments just above and below the eutectoid temperature. These precipitate forms are termed (i) primary, (ii) large random, and (iii) secondary. Further precipitation, slow growth of existing precipitates, and subeutectoid decomposition result when an additional 1100"0C aging treatment is given to the previously cooled material. It is shown that type (iii) secondary precipitates from rapidly within the temperature range of 1300"0 to 1375"0C. The secondary precipitates are largely responsible for the improved room-temperature strength properties of the heat-treated samples. The formation and effects on mechanical properties of each type of precipitate are ...

International Nuclear Information System (INIS)

This paper presents the results of experimental study carried out to know whether the salicylic acid used as an additive during the precipitation of zirconium using ammonium hydroxide solution goes into the filtrate, remains in the hydrated zirconia or gets distributed between the both under the ambient conditions of precipitation. Keeping its simplicity and amenability to adopt on a routine basis, spectrophotometric method has been chosen for the purpose among the many methods available and the problems associated in determining salicylic acid in the presence of zirconium and the medial measures to circumvent the same have been brought out in detail. (author)

British Library Electronic Table of Contents (United Kingdom)

Due to the low thermal conductivity of ceramics large temperature gradients are present through the powder particles during plasma spray deposition. As a result the particles often impinge at the substrate in a semi-molten form; which in turn substantially affects the final characteristics of the coating being formed. This study is dedicated to the novel modelling development and simulation of a semi-molten droplet impingement. The study examines the impingement process during impact, spreading and solidification of semi-molten zirconia. The simulation provides an insight to the heat transfer process during impact and solidification of a semi-molten powder particle and illustrates the freezing-induced break-up mechanism at the splat periphery.

Energy Technology Data Exchange (ETDEWEB)

In support of the efforts to apply ceramics in advanced heat engines, a study was made of the sliding performance of ceramics at the ring/cylinder interface of low heat rejection engines. The objective was to understand the basic mechanisms controlling the wear of candidate ceramics and thereby identify means for applying these ceramics effectively. Attempts to operate three different zirconias, silicon carbide, silicon nitride, and several plasma-sprayed ceramic coatings without lubrication were unsuccessful because of high friction and high wear rates. Experiments using a polyalphaolefin lubricant at temperatures to 260 C identified several combinations having wear rates in the general range likely to be acceptable for engines. Plasma-sprayed coatings of chromium oxide and hypersonic powder flame sprayed coatings of cobalt-bonded tungsten carbide performed particularly well as ring coatings. Similar performance was obtained with these ring coatings operating ...

International Nuclear Information System (INIS)

The results of a combined investigation of splat-quenched Fe-Csub(x) (x<0.05) alloys by resistivity, X-ray diffraction and Moessbauer spectroscopy are presented. The residual resistivity increases linearly with the carbon content (#DELTA#rho=5#mu##OMEGA#cm/at.%) with a slope identical to that observed in the dilute ferritic phase. X-ray diffraction reveals the presence of a martensite structure in addition to a small fraction of residual austenite; the dependence of the a and c lattice parameters on xsub(c) agrees with earlier measurements. A detailed investigation of the relative reflexion intensities shows that the as-quenched martensites consist of a mixing of massive martensite and tetragonal martensite for low carbon content and of tetragonal martensite only for xsub(c) approximately 0.05. The Moessbauer spectra reveal 3 or 4 magnetically non equivalent iron sites. From a detailed analysis of the intensity dependence of the subspectra ...

International Nuclear Information System (INIS)

New data about the structure of high-temperature resistant metalloceramic plasma sprayed coatings in micro and nano areas are presented. Application of the new instrumental methods: transmission electron microscopy combined with selected area electron diffraction mode is possible to obtain these data. The first layer in Ni based metallic bond coat shows nanocrystalline structure. External ceramic layer based on stabilised ZrO_2 is polycrystalline and contains both cubic and tetragonal crystalline phases. Local inhomogeneities in coatings phase composition are determined. (author)

International Nuclear Information System (INIS)

Single-crystalline CeRh_2Si_2 and CePd_2Si_2 were grown by the Czochralsky pulling method and the temperature dependence of magnetic susceptibility was investigated. The crystalline electric field (CEF) states in each compound were determined by considering the tetragonal CEF Hamiltonian with mean-field approximation. Interactions between Ce"3"+ ion and the surrounding ligands in CeRh_2Si_2 turned out to be strong and highly anisotropic in comparison to CePd_2Si_2. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The refractory nature and high ductility of body centered cubic (bcc) phase tantalum makes it a suitable material for corrosion- and wear-resistant coatings on surfaces that are subjected to high stresses and harsh chemical and erosive environments. Sputter deposition can produce thick tantalum films but is prone to forming the brittle tetragonal beta phase of this material. Efforts aimed at forming thick bcc phase tantalum coatings in both flat plate and cylindrical geometries by high-rate triode sputtering methods are discussed. In addition to substrate temperature, the bcc-to-beta phase ratio in sputtered tantalum coatings is shown to be sensitive to other substrate surface effects.

International Nuclear Information System (INIS)

A technique for following sialon formation in situ by high temperature X-ray diffraction (HT-XRD) was developed. The composition chosen for study was an yttrium #alpha#-sialon with x=0.4. Powder compacts containing silicon nitride, aluminum nitride and yttria powders were pre-sintered at 1350 C and then studied by HT-XRD at temperatures between 1450 and 1580 C and nitrogen pressures of 0.11 MPa. The furnace was made from graphite coated with porous silicon nitride/silicon carbide. The coating prevented silicon carbide formation in the sample up to 1600 C. X-ray diffraction results show the formation of a Y_1_0Al_2Si_3O_1_8N_4 phase at 1350 C, which dissolved to form #alpha#-sialon and other phases at higher temperatures. The amounts of #alpha#-sialon formed are similar to the amounts reported by other authors. An empirical method was used for the calculation of activation energy for the silicon nitride to #alpha#-sialon transformation and resulted in a value of 330 ...

Energy Technology Data Exchange (ETDEWEB)

In support of the efforts to apply ceramics to advanced heat engines, a study is being performed of the performance of ceramics at the ring/cylinder interface of advanced (low heat rejection) engines. The objective of the study, managed by the Oak Ridge National Laboratory, is to understand the basic mechanisms controlling the wear of ceramics and thereby identify means for applying ceramics effectively. Attempts to operate three different zirconias, silicon carbide, silicon nitride, and plasma-sprayed ceramic coatings without lubrication have not been successful because of excessive friction and high wear rates. Silicon carbide and silicon nitride perform well at ambient temperatures with fully formulated mineral oil lubrication, but are limited to temperatures of 500F because of the lack of suitable liquid lubricants for higher temperatures.

British Library Electronic Table of Contents (United Kingdom)

Objective.The interest of dental research in metal-free restorations has been rising in the last 20 years following the introduction of innovative all-ceramic materials in the daily practice. In particular, high strength ceramics and related CAD/CAM techniques have widely increased the clinical indications of metal-free prostheses, showing more favourable mechanical characteristics compared to the early ceramic materials.The purpose of the present paper is providing a brief review on the all-ceramic dental materials, evaluating pros and cons in the light of the most recent scientific results and of the authors? clinical experience.Materials. A structured review of the literature was given on the basis of medical and engineering papers published in the last decades on the use of dental cera...

Energy Technology Data Exchange (ETDEWEB)

A number of materials of composition YSr{sub 2}Cu{sub 3-x}MxO{sub 7{+-}y} with M = Ti, Fe, Co, Al, Ga and Pb were prepared by solid state reactions. They belong to the tetragonal P4/mmm space group and their unit cell parameters were determined and refined from X-ray powder data. The infrared spectra of the compounds were also recorded and are briefly discussed on the basis of their structural characteristics and by comparison with those of related materials. (orig.) 23 refs.

International Nuclear Information System (INIS)

Neutron diffraction and magnetometric measurements on polycrystalline samples of DyPd_2Si_2 and ErPd_2Si_2 were carried out in the temperature range from 2 to 293 K. Both compounds show tetragonal ThCr_2Si_2 type crystal structure and order at 12 K in a sine modulated magnetic structure with propagation vectors k=[0.609,0,0.155] and [0.575, 0, 0.083] respectively. The oscillatory character of magnetic order found in RPd_2Si_2 (R=Tb-Er) compounds suggests exchange interaction described by the RKKY model to be dominant, but the non-monotonic dependence of respective Neel temperatures on the number of f-electrons indicates the influence of a crystalline electric field (CEF) on the magnetic behaviour in this series. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The refractory nature and high ductility of body centered cubic (bcc) phase tantalum makes it a suitable material for corrosion- and wear-resistant coatings on surfaces which are subjected to high stresses and harsh chemical and erosive environments. Sputter deposition can produce thick tantalum films but is prone to forming the brittle tetragonal beta phase of this material. Efforts aimed at forming thick bcc phase tantalum coatings in both flat plate and cylindrical geometries by high-rate triode sputtering methods are discussed. In addition to substrate temperature, the bcc-to-beta phase ratio in sputtered tantalum coatings is shown to be sensitive to other substrate surface effects.

Science.gov (United States)

We report significant enhancement in superconducting properties of yttrium substituted Ce1-xYxOFFeAs superconductors. The polycrystalline samples were prepared by two step solid state reaction technique. X-ray diffraction confirmed tetragonal ZrCuSiAs structure with decrease in both a and c lattice parameters on increasing yttrium substitution (with fixed F content). With smaller ion Y in place of Ce, the transition temperature increased by 6 K. Yttrium doping also lead to higher critical fields as well as broader magnetization loops, particularly at elevated temperature.

International Nuclear Information System (INIS)

The crystal structure, lattice strain due to the antiferromagnetic ordering, and magnetic form factor in the itinerant 5f compounds UTGa_5 (T=Ni, Pd, Pt) have been studied by neutron scattering. High-resolution powder diffraction revealed that the tetragonality of the U-Ga layers increases down to the series of the transition metal element T. The integrated intensities of the antiferromagnetic reflections can be well explained with the Neel-type structure for UNiGa_5, whereas UPtGa_5 has the antiferromagnetic stacking of the ferromagnetically ordered uranium moments in the c plane. In both compounds the uranium moments orient along the c axis with moments of 0.75(5) and 0.32(5) #mu#_B for UNiGa_5 and UPtGa_5, respectively. No magnetic peak could be observed in the powder diffraction pattern of UPdGa_5 due to the small magnetic moment less than the experimental sensitivity. The orbital contributions in the magnetic form factor are reduced from the free-ion value, ...

Science.gov (United States)

Lead-free piezoelectric ceramics (1-x)K0.5Na0.5NbO3-xAgSbO3+0.75 mol % MnO2 were prepared by a conventional solid-state sintering technique, and the piezoelectric and dielectric properties of the ceramics were studied. The results of x-ray diffraction suggest that AgSbO3 diffuses into the K0.5Na0.5NbO3 lattices to form a new solid solution with a single-phase orthorhombic perovskite structure. After the addition of AgSbO3, the paraelectric cubic-ferroelectric tetragonal phase transition temperature (TC) and the ferroelectric tetragonal-ferroelectric orthorhombic phase transition temperature (TO-T) decrease, and the ceramics become ``softened,'' resulting in significant improvements in the ferroelectric and piezoelectric properties. The ceramics with x=0.03-0.10 exhibit excellent piezoelectric properties: d33=130-216 pC/N, kp=0.44-0.51, and kt=0.40-0.52. The ceramics also exhibit a good thermal stability up to high TO-T, suggesting that the ...

Energy Technology Data Exchange (ETDEWEB)

An advanced process for the separation of hydrogen sulfide (H{sub 2}S) from coal gasification product streams through an electrochemical membrane is being developed. H{sub 2}S is removed from the syn-gas stream, split into hydrogen, which enriches the exiting syn-gas, and sulfur, which is condensed from an inert sweep gas stream. The process allows removal of H{sub 2}S without cooling the gas stream and with negligible pressure loss through the separator. The process is made economically attractive by the lack of need for a Claus process for sulfur recovery. Membrane manufacturing coupled with full-cell experimentation was the primary focus this quarter. A tape-casted zirconia membrane was developed and utilized in one full-cell experiment (run 25); run 24 utilized a fabricated membrane purchased from Zircar Corporation. Results are discussed.

Energy Technology Data Exchange (ETDEWEB)

An experimental investigation of premixed methane-air combustion within the one-dimensional porous ceramic burners for various burner configurations is presented. The burner is nonhomogeneous because of different pore size ceramic block used in different section of the burner. Therefore, the thermophysical and transport properties are nonuniform along the burner core length. The burners are constructed of partially stabilized zirconia. The CO and NO{sub x} emissions, flame speed, and flame stability are examined and compared at lean equivalence ratios for five different burner configurations. The sandwich-structured burner has very favorable flame stabilizing characteristic due to the radiation reflecting region. While the combustion proceeds at faster rate than other burner configurations, the radiation reflecting region and the exit surface have low temperature. Thus the NO{sub x} emission can be kept at the same low level as the other burner configurations ...

Energy Technology Data Exchange (ETDEWEB)

The feasibility of using hydrogen as the sole fuel in a direct injection diesel engine was investigated. An air cooled single cylinder Lister ST1 diesel engine was modified to operate as a low-heat-rejection engine for this study. Partially stabilized zirconia ceramic parts were used to shield the combustion space of the engine. Using a compression ratio of 17.9:1 and motoring the test engine at 21000 rpm, a maximum compression temperature of approximately 900 K was achieved. Under these operating conditions, all lubricants tested were found to burn. Lowering the speed to 1450 rpm and the compression ratio to 17.1, lubricant combustion and hot spots were successfully eliminated. The maximum compression temperature, when compression ignition of hydrogen was tried, was in the 800 K range. The corresponding ceramic surface temperature was estimated to reach 600-700 K. Only sporadic compression ignition of hydrogen was achievable. (author).

International Nuclear Information System (INIS)

For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO2, PrO2), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two shapes: small cubic (oxide) and large plate-like (tetragonal) structures. The conversion efficiencies of the rare earth elements to their molten salt-insoluble precipitates were ...

Energy Technology Data Exchange (ETDEWEB)

A discussion is given concerning the transformation in acid medium of curite into copper-, nickel- and cobalt-uranylphosphate. From chemical, differential thermal and thermogravimetric analyses, the crystal-chemical formula are calculated as: Cu(UO/sub 2//PO/sub 4/)/sub 2/.8H/sub 2/O, Ni(UO/sub 2//PO/sub 4/)/sub 2/.7H/sub 2/O and Co(UO/sub 2//PO/sub 4/)/sub 2/.7H/sub 2/O. The two last compounds crystallize in the triclinic system with space group P1 or P1(overscore) and the first one crystallizes in the tetragonal system with space group P4/nmm. The cell parameters are calculated. From solubility data, the solubility products are computed as 10sup(-12.8), 10sup(-9.5) and 10sup(-9.9) for the copper-, nickel- and colbalt-compound respectively. The electrokinetic properties of the three species are closely similar to those of natural meta-torbernite: the zeta-potential is negative and the point of zero charge be reached cannot in the pH-range 2 to 9.

British Library Electronic Table of Contents (United Kingdom)

Here in the present paper, we report on growth of stoichiometric and nonstoichiometric nanostructured heterojunction solar cell of CdS/CuInSXSe2-X varying X from 0 to 2 in the interval of 0.5 using cost effective, simple, chemical ion exchange method at room temperature on ITO glass substrate. The as-grown varying composition solar cells annealed at 200degreeC in air and characterized for structural, compositional, optical and illumination studies. The X-ray diffraction pattern obtained from CdS/CuInSXSe2-X solar cell confirms the formation of CuInSe2, CuInS0.5Se1.5, CuInS1Se1, CuInS1.5Se0.5 and CuInS2 phases having tetragonal structure with varying crystallite size from 19, 19.37, 28, 33 and 20nm respectively. The energy dispersive X-ray analysis (EDAX) confirms the expected elemental com...

International Nuclear Information System (INIS)

The amorphization of a quenched sample of the GaSb-II high-pressure phase was studied at ambient pressure by real-time neutron diffraction in the course of the sample heating from 100 K to room temperature at a rate of 0.4 K min-1. The transformation to the amorphous state begins at 140 K and is completed near room temperature. The ?-Sn type structure was shown to represent only the mean lattice of the high-pressure GaSb-II phase. The superstructure of this phase widely varied with temperature and is caused by the ordered displacement of atoms. The temperature range of the metastable crystalline phase relaxation is divided into three intervals according to the temperature dependence of the tetragonality ratio (c/a). At the boundaries of these temperature intervals, i.e. temperatures T = 170 and 230 K, two second-order phase transitions are observed. Anomalous heat and volumetric effects were observed earlier by means of calorimetry and dilatometry in the same ...

International Nuclear Information System (INIS)

In this study, SnO2 thin films have been grown using spray pyrolysis technique on glass substrates under a substrate temperature (Ts = 440 oC). The precursors were methanol CH4O and anhydrous tin tetrachloride. XRD analyses yielded strong (1 1 0)-(1 0 1)-(2 0 0) X-ray diffraction peaks which are characteristics to tetragonal crystals. Atomic Force Microscopy (AFM) analyses showed the existence of clusters with particular pyramidal shapes. The main part of this study concerns the optical measurements of transmittance T(?) and reflectance R(?) spectra inside 250-1800 nm domain. Conjoint optical and thermal properties were deduced using the Amlouk-Boubaker Opto-Thermal Expansivity ?AB. The obtained value: ?AB ? 23.4 m3 s-1 helped situating the performance of the as-grown SnO2 compound among most known PV-T oxides like ZnO and TiO2.

British Library Electronic Table of Contents (United Kingdom)

Abstract Lithium-indium oxide is one of the candidate materials as solid-state scintillators for solar neutrinos due to an inverse --decay of 115In to 115Sn. On the other hand, when doped with rare-earth ions such as Eu3+ or Sm3+, it becomes a promising phosphor material. In this report we present a simple solid-state procedure for preparation of LiInO2:Eu3+ powders. X-ray diffraction confirmed prod-uct in tetragonal structural form (space group: I41/amd) and no impurity phases were detected. Then, high resolution photoluminescence emission measurements were performed at room and low temperatures to find 5D0 - 7FJ. Emission kinetics from 5D0 level exhibited pure single exponential behavior with lifetime of about 1.5 ms. Maximum energy splitting of 7F1 manifold is recorded as a function of ...

International Nuclear Information System (INIS)

Neutron powder diffraction and magnetometric studies of the HoRh_2_-_xPd_xSi_2 series of solid solutions (x=0, 0.5, 0.75, 1.0, 1.5, 1.8) are reported. The intermetallics investigated crystallize in the body-centred-tetragonal ThCr_2Si_2-type structure (space group I4/mmm). All the samples order antiferromagnetically at low temperatures. For low values of the dilution parameter x a simple collinear antiferromagnetic structure of the AFI type is stable. Below T_N the magnetic moments are parallel to the c-axis and then, below T_t, deflect forming an angle #psi# with the c-axis. Further replacement of Rh by Pd results in the development of a sine-wave-modulated magnetic structure with one two-component propagation vector and magnetic moments in the basal plane. For x=1.8 a sine-wave-modulated structure similar to that reported for HoPd_2Si_2 (i.e. with a two-component propagation vector and magnetic moments parallel to the b-axis) was found. (author)

Energy Technology Data Exchange (ETDEWEB)

The influence of Pd-Ni substitution on the formation of magnetic phases in the tetragonal U(Ni{sub 1-x}, Pd{sub x}){sub 2}Si{sub 2} system and the concentration magnetic phase diagram are presented. A series of different substitutions was prepared and detailed studies by powder neutron diffraction were performed for x=0.25, 0.5 and 0.75. All compounds order antiferromagnetically and form ferromagnetic basal planes stacked along the c axis (q=(0,0,q{sub z}) propagation). The ground-state phase (AF3) of UNi{sub 2}Si{sub 2} is an uncompensated AF structure (++- stacking (q{sub z}=2/3)). In UPd{sub 2}Si{sub 2} the ground-state phase corresponds to the simple AF structure AF2 (+-+-(q{sub z}=1)). In solid solutions, no traces of the AF3 phase were found for x=0.25 and the ground-state powder patterns correspond to AF2 for x{>=}0.25. (orig.)

International Nuclear Information System (INIS)

Three types of titanium hydrides have been reported: #delta#, #epsilon# and #gamma# hydrides. The #delta# hydride forms in the composition range from TiH/sub 1.5/ to TiH/sub 1.99/ and has a CaF/sub 2/ structure with metal atoms on an fcc lattice and hydrogen atoms randomly occupying tetrahedral interstitial sites. At higher hydrogen concentrations, TiH/sub 2/, the fct (c/a # #epsilon# transformation is apparently diffusionless, similar to that operating in the cubic/tetragonal transformation in zirconium hydride. The metastable fct #gamma# hydride having a c/a value of 1.09 or 1.12 forms from solid solutions of hydrogen in the hcp #alpha# matrix. While the titanium hydride precipitation in #alpha#-Ti and its alloys has attracted extensive investigation, hydride formation in bcc #beta#-Ti alloys has rarely been studied because they have not been thought to be liable to hydride formation. This paper shows conclusive evidence for the fcc #delta# hydride phase ...

Energy Technology Data Exchange (ETDEWEB)

This work has been undertaken with a view to study the effect of lanthanum content on properties of PLZT ceramics. The polycrystalline complex compounds of PLZT with Pb{sub 1-x}La{sub x}(Zr{sub 0.40}Ti{sub 0.60}){sub 1-x/4}O{sub 3}, +10% PbO formula were prepared from the nano-size individual oxides powders by hot-pressed process. Transparent PLZT (x/40/60) bulk ceramics with pure tetragonal phase was obtained. The studies of the microstructures, dielectric and ferroelectric properties of the ceramics were carried out. The experiment results showed that when La content increased from 7 to 13 mol.%, the grain size increased from 2 to 7 {mu}m. La content also effects the dielectric property obviously, the dielectric constant increased with La content increasing. Moreover, the ferroelectric properties are sensitive to the variation of La content.

International Nuclear Information System (INIS)

Electron paramagnetic resonance (EPR), optical, infrared and Raman spectral studies have been carried out on vanadyl ions doped in polyvinylalcohol (PVA) films. The spin-Hamiltonian parameters (g and A) and the molecular orbital coefficients (#beta#_2"*"2 and k) have been evaluated. The values of spin-Hamiltonian parameters confirm that the vanadyl ions are present in PVA films as VO"2"+ molecular ions in an octahedral site with a tetragonal compression (C_4_v). The temperature variation EPR studies reveal that the variation of number of spins with temperature is in accordance with Boltzmann law. It is interesting to observe that the variation of susceptibility with temperature obeys Curie-Weiss law. The FT-IR and FT-Raman spectrum exhibits few bands, which are attributed to O-H, C-H, C-C and C-O groups of stretching and bending vibrations. The optical absorption spectrum exhibits two bands, which are assigned to "2B_2_g->"2B_1_g and "2B_2_g->"2E_g ...

International Nuclear Information System (INIS)

A phenomenological simulation was carried out for 41 experimental crystal-field (CF) levels within the "4I_9_/_2_-_1_5_/_2, "4F_3_/_2_-_9_/_2, "4S_3_/_2 and "2H_9_/_2 J manifolds, including the available infrared (IR) data up to #approx#15 000 cm"-"1 for the Nd"3"+ ions in the Nd_2CuO_4 single crystals. The CF Hamiltonian for the tetragonal C_4_v symmetry was diagonalized together with the free-ion Hamiltonian in a basis that spans the entire 4f"3 configuration. A rms error of 9 cm"-"1 between the calculated and experimental energy level schemes was obtained. A comparison of the spectra in the visible region between the insulating Nd_2CuO_4 and the metallic Nd_2_-_xCe_xCuO_4, allowed identifying the absorption bands associated with the development of the charge-doping induced local structural distortions in the superconducting regime.

Energy Technology Data Exchange (ETDEWEB)

Fuel cells based on solid oxides ('SOFC') are excellent alternative devices for power generation, when they are operated at high temperature, e.g. above 600 C. Having only fixed parts for the power generating part of the device is only one advantage of the fuel cell. Due to their unique design, these devices offer a maximum of efficiency for energy conversion compared to conventional power generating systems, which are mainly based on turbines. One aim of this thesis is the examination of alternative electrolyte and cathode materials for the SOFC applications at reduced temperatures, which means in the temperature range between 600 C and 750 C. For the first main task, several materials from the oxygen ion conducting electrolytes were selected. Different strontium and magnesium doped lanthanum gallate (LSGM) materials with additional transition metal doping were selected and prepared via two different preparation methods. The optimum calcining conditions were ...

Energy Technology Data Exchange (ETDEWEB)

The objective of the first project period is to: make a study into materials suitable for the non-premix radiant burners (NPRB); choose the materials for the construction; make proposals for the design of the NPRB; test the different proposals with a CFD-model. In pursuit of finding a suitable material it is necessary first to estimate the maximum temperature that will occur in the burner. It has been estimated that the maximum adiabatic flame temperature will be about 2400-2500 K. The maximum temperature in the burner will of course never reach this level. A more realistic temperature was estimated to 2100-2300 K. The final choice was made after having contacted some of the leading producers. It was possible to find one producer that could produce burners of one of the suggested materials, zirconia. Several construction ideas for the NPRB have been discussed and some of them tested with a CFD-model. The proposed burner concept has been modified in order to obtain ...

International Nuclear Information System (INIS)

Structure and magnetic properties of UNi_1_0_-_xFe_xSi_2 intermetallics and "2"9Si nuclear magnetic resonance (NMR) in UNi_1_0Si_2 are investigated in a wide temperature range. Solid solutions in the exactly single-phase tetragonal form, ThMn_1_2 type, exist for x<2. The Ni and Fe atoms occupy the 8(f), 8(i) and 8(j) positions statistically, whereas the U atoms occupy the 2(a) and the Si atoms the 8(j) sites. The lattice parameters roughly follow Vegard's law. The magnetic susceptibility does not exhibit Curie-Weiss behaviour and, at about 630 K, an anomaly in the temperature dependence is observed. At low temperature, other anomalies are observed at 32 K and 45 K, for x=0.5 and 1.0 respectively. These low temperature anomalies are probably connected with magnetic ordering of a ferromagnetic character, whereas that at 630 K might result from the superparamagnetic state of Ni. Two "2"9Si NMR lines in UNi"1"0Si"2 were observed with the Knight shift being ...

International Nuclear Information System (INIS)

The effects of catalytic metal additives on the hydrogen desorption properties of the submicrocrystalline magnesium hydride (#beta#-MgH_2) formed after hydrogenation of the Mg + 10 wt.%X (X = V, Y, Zr) mechanically (ball) milled composites were studied. The composites with catalytic metals were processed by controlled mechanical milling (CMM) in the magneto-mill Uni Ball Mill 5 under protective Ar atmosphere. X-ray diffraction of the milled powders revealed the formation of Mg nanograins (50-60 nm range) interdispersed with the nanograined metal additives within the powder particles. Scanning electron microscopy showed particle size reduction after milling. After activation and hydrogenation in a Sieverts-type apparatus under about 2 MPa pressure of hydrogen, the tetragonal #beta#-MgH_2 hydride co-exists with the small amount of retained unreacted Mg phase and the small amount of MgO in all three composites. The #beta#-MgH_2 phase after hydrogenation is ...

Energy Technology Data Exchange (ETDEWEB)

Among the three modifications of calcium sulfite hemihydrate, two of them, hexagonal ..beta..-CaSO/sub 3/.1/2H/sub 2/O with a rhombohedral lattice and ..gamma..-CaSO/sub 3/.1/2H/sub 2/O with a simple triangular hexagonal lattice, were found in the authors' recent work. By heating ..cap alpha..- and/or ..gamma..-hemihydrate at 330-360/sup 0/C in a nitrogen atmosphere, the orthorhombic anhydrate ..cap alpha..-CaSO/sub 3/ was formed, with lattice constants of 6.472, 15.93, and 23.44 angstrom for a, b, and c respectively, while the body-centered tetragonal anhydrate ..beta..-CaSO/sub 3/, with lattice constants of 15.68 and 19.44 angstrom for a and c respectively, was formed by heating the ..beta..-hemihydrate. The dehydration of three hemihydrates and the hydration of two anhydrates were discussed. Calcium sulfite hemihydrate (CaSO/sub 3/.1/2H/sub 2/O) is useful as an architectural material since it has a high thermal stability and a low water solubility in ...

Energy Technology Data Exchange (ETDEWEB)

This report describes the QUEOS facility and gives the results of the first test series performed up to 6/1995. The premixing phase of a steam explosion is investigated experimentally with simulant materials. The transient three-dimensional multi-component interaction of molten corium with water is studied using a large number of small solid spheres at temperatures up to 2300 C. The objective of the experiments is to establish a data base for testing the models of heat and momentum transfer in multi-fluid codes as well as the code`s capability to correctly describe multiphase flows. The experiments have the advantage that the diameter of the `coarse melt fragments` are known and that detailed measurements can be performed without the danger of a steam explosion. In this first series of experiments up to 10 kg of spheres (max. 24000 pieces) were used. The spheres, made of molybdenum or zirconia, were heated to temperatures up to 2000 C and are discharged into 0.5 ...