Energy Technology Data Exchange (ETDEWEB)

The authors report the fabrication and characterization of a low temperature (200--400 C) thin film gas sensor constructed from a MOCVD-grown yttria-stabilized zirconia (YSZ) layer sandwiched between two platinum thin film electrodes. A reproducible gas-sensing response is produced by applying a cyclic voltage which generates voltammograms with gas-specific current peaks and shapes. Growth conditions are optimized for preparing YSZ films having dense microstructures, low leakage currents, and maximum ion conductivities. In particular, the effect of growth temperature on film morphology and texture is discussed and related to the electrical and gas-sensing properties of the thin film sensor device.

Science.gov (United States)

The Swedish Ceramic Institute is an industrial research institute working with product-oriented research and development of ceramics and closely related materials. The institute works with the processing and fabrication of ceramic materials as well as with materials properties and design questions. Its website provides details of research projects (engineering ceramics, electroceramics, traditional ceramics). Publications are listed, with some downloadable files (annual reports, research reports, information leaflets). Sample materials data (mechanical properties, thermal properties) is given for oxides and non-oxide ceramics.

British Library Electronic Table of Contents (United Kingdom)

The main drawback of Ni/YSZ anode supports for solid oxide fuel cell application is their low tolerance to reducing and oxidizing (RedOx) atmosphere changes, owing to the Ni/NiO volume variation. This work describes a structured approach based on design of experiments for optimizing the microstructure for RedOx stability enhancement. A full factorial hypercube design and the response surface methodology are applied with the variables and their variation range defined as: (1) NiO proportion (40-60wt% of the ceramic powders), (2) pore-former proportion (0-30wt% corresponding to 0-64vol.%), (3) NiO particle size (0.5-8mm) and (4) 8YSZ particle size (0.6-9mm). To obtain quadratic response models, 25 different compositions were prepared forming a central composite design. The measured responses...

International Nuclear Information System (INIS)

The fabrication of the ZT-40 torus, a large complex all-ceramic toroidal plasma containment vessel, is described. Several glass sealants covering the temperature range of 500 to 1300"0C, were developed and used to ''braze'' segments of the torus together, sapphire windows to the torus and the required pump-out and diagnostic parts to the ceramic vacuum vessel. Designs of window seals were developed that allowed sealing of the sapphire windows in a vertical position with minimum sealing glass flow.

British Library Electronic Table of Contents (United Kingdom)

Rapid nitridation was used to fabricate reaction-bonded and postsintered -Si6-ZAlZOZN8-Z (Z=1) ceramics with monoclinic ZrO2 added to the starting powder. Thermo-gravimetric analysis revealed that the addition of ZrO2 reduced the starting temperature of the main nitridation reaction. Using a reaction-bonding route with heating rates of 5, 10, and 20C/min, to fabricate -SiAlON ceramics without ZrO2 resulted in unreacted silicon that bled out of the specimens and the Z=1 composition samples did not maintain the original green compact morphology. On the other hand, no such bleeding of melted silicon was observed for samples with ZrO2 additions and the samples following nitridation maintained the original green morphology. The microstructure and mechanical properties of samples produced by rap...

British Library Electronic Table of Contents (United Kingdom)

Statement of problem Computer-aided design/computer-aided manufacturing (CAD/CAM) titanium ceramic restorations were developed with the potential for replacing expensive, high noble metal ceramic restorations. However, there is a lack of information about the clinical performance of CAD/CAM titanium ceramic single crowns. Purpose The purpose of this study was to evaluate CAD/CAM titanium ceramic single crowns after 3 years in function. Material and methods A total of 41 crowns were fabricated for 21 patients. The titanium copings were CAD/CAM milled (Everest CAD/CAM system) with an even thickness of 0.5 mm, and low-fusing veneering porcelain (Vita Titanium Porcelain) was added incrementally. The crowns were cemented using zinc phosphate cement after confirming that there were no mechanical...

British Library Electronic Table of Contents (United Kingdom)

Abstract Purpose: The aim of this in vitro study was to compare the marginal adaptation of a pressed ceramic material, when used with and without a metal substructure, to a traditional feldspathic porcelain-fused-to-metal restoration with a porcelain butt margin. Materials and Methods: A maxillary central incisor typodont tooth was prepared with a 1.5 mm 360degree shoulder with rounded internal line angle, and 30 polyether impressions were made. Dies were poured in type IV dental stone, and 30 restorations were fabricated: 10 metal ceramic restorations (MCR) with porcelain butt joints, 10 pressed to metal restorations (PTM), and 10 all-ceramic restorations (PCR). All restorations were evaluated on their respective dies at 45x magnification using an Olympus SZX-12, measurements of the margi...

International Nuclear Information System (INIS)

(#alpha#+#beta#)-SiALON ceramic composites are industrially important materials. Due to their unique chemistry, crystal structure and microstructural features, #alpha#-SiAlON has superior hardness while #beta#-SiALON offers high strength and toughness. The combination of the two phases enables materials engineers to design a ceramic where the physical properties of the composite can be tailored to a particular application. This article presents a general review of the crystal structures, fabrication and properties of the (#alpha#+#beta#)-SiALON composites with special highlights outlining how microstructural tailoring can control the properties of these advanced ceramic alloys. Copyright (1997) Institute of Metals and Materials Australasia Ltd.

Energy Technology Data Exchange (ETDEWEB)

For several decades most of the efforts to develop new scintillator materials have concentrated on high-light-yield inorganic single-crystals while polycrystalline ceramic scintillators, since their inception in the early 1980 s, have received relatively little attention. Nevertheless, transparent ceramics offer a promising approach to the fabrication of relatively inexpensive scintillators via a simple mechanical compaction and annealing process that eliminates single-crystal growth. Until recently, commonly accepted concepts restricted the polycrystalline ceramic approach to materials exhibiting a cubic crystal structure. Here, we report our results on the development of two novel ceramic scintillators based on the non-cubic crystalline materials: Lu SiO:Ce (LSO:Ce) and LaBr:Ce. While no evidence for texturing has been found in their ceramic microstructures, ...

International Nuclear Information System (INIS)

BaTi_0_._9(Ni_1_/_2W_1_/_2)_0_._1O_3 ceramics were fabricated and their dielectric properties were investigated. With the sintering temperature increasing from 1250 to 1280 deg. C, the grain size abruptly increases from 1-2 to 20-40 #mu#m, accompanying significant changes in dielectric response. The samples with larger grains exhibit giant dielectric constant characteristics, which are considered to be mainly attributed to the domain boundary effect. The activation energies of the dielectric relaxation E_r_e_l_a_x=0.325 eV reveal the existence of microdomains in larger grains. The ac conductivity results also give the evidence of the domain boundary effect in the present ceramics.

Energy Technology Data Exchange (ETDEWEB)

This specification establishes requirements for design, testing, and quality assurance for electric heaters that will be used to maintain primary Sodium temperature in the Fast Test Facility (FFTF) reactor vessel. The Test Specification (WHC-SD-FF-SDS-003) has been revised to Rev. 1. This change modifies the fabrication of approximately 25 feet of the subject heater using ceramic insulators over the heater lead wire rather than compressed magnesium oxide. Also, 304 or 316 stainless steel can be used for the heater sheath. This change should simplify fabrication and improve the heater operational reliability.

Energy Technology Data Exchange (ETDEWEB)

For many industrial applications, materials are desired which combine light weight, high temperature strength, and stability in corrosive environments. Among competing materials, ceramics are noteworthy candidates for such applications. The use of ceramics is often constrained, however, by brittleness; i.e., low toughness. Ceramic composites are being developed to overcome this limitation. With recent advances in ceramic fiber technology, it is possible to design a composite material based on continuous ceramic fibers embedded in a ceramic matrix. The use of ceramic composites in industrial applications will result in reduced fuel consumption, but will also prevent airborne pollution (principally NO, SO{sub x}, CO{sub 2}, and particulates), and economically benefit the end user through energy and environmental savings and increased ...

Energy Technology Data Exchange (ETDEWEB)

A pillbox RF output window was developed for the L-band pulsed klystron for the Japanese Hadron Project (JHP) 1-GeV proton linac. The window was designed to withstand a peak RF power of 6 MW, where the pulse width is 600 {mu}sec and the repetition rate is 50 Hz. A high power model was fabricated using an alumina ceramic which has a low loss tangent of 2.5x10{sup -5}. A high power test was successfully performed up to a 113 kW RF average power with a 4 MW peak power, a 565 {mu}sec pulse width and a 50 Hz repetition rate. By extrapolating the data of this high power test, the temperature rise of the ceramic is estimated low enough at the full RF power of 6 MW. Thus this RF window is expected to satisfy the specifications of the L-band Klystron. (author).

Energy Technology Data Exchange (ETDEWEB)

The bibliography contains citations concerning plasma immersion ion implantation (PIII) and equipment. PIII is a new technique to implant plasma ions into materials for surface modification and treatment. Topics include plasma nitriding, semiconductor doping, ion energy distribution, ion dose, pulsed plasma, metal plasma, and defect passivation. References also review applications in semiconductor device and integrated circuit manufacture, silicon material fabrication, aerospace bearings, carbon coatings on metals, and ceramic coatings. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

Energy Technology Data Exchange (ETDEWEB)

The project has been developing Yttria Stabilized Zirconia (YSZ)-Alumina Composites as an electrolyte of a self-support type planar Solid Oxide Fuel Cell (SOFC) from the following points of view: a path of alumina particles with high thermal conductivity can be designed as an electrolyte sheet; there are some possibilities that the electrolyte can be enhanced in mechanical strength. As previously reported, these composite materials have higher mechanical strength and better thermal shock resistance than those of YSZ. These composites containing 0-30 wt% of Al[sub 2]O[sub 3] were measured by AC impedance method at temperatures of 250-1,000[degree]C. Electrical conductivities of 8YSZ without Al[sub 2]O[sub 3] and a composite consisting of 80 wt% YSZ and 20 wt%Al[sub 2]O[sub 3] as sintered samples were 1.2 x 10[sup -1]S/cm and 1.0 x 10[sup -1]S/cm respectively at 1,000[degree]C. The composite containing 20 ...

Energy Technology Data Exchange (ETDEWEB)

Fabrication processes for FFTF fuel pins are described.

Science.gov (United States)

Ceramic and Dental Enamel Wear

Science.gov (United States)

Joint Diseases

Energy Technology Data Exchange (ETDEWEB)

The effect of interfacial structure on the mechanical properties of aluminum-ceramic composite materials fabricated by liquid phase sintering was studied. The composites were based on two matrix alloys (powder metallurgy alloys 201 and 601) reinforced with either Al{sub 2}O{sub 3} or SiC particulate. Characterization of the interfacial regions demonstrated that the SiC-matrix interfaces were faceted whereas the Al{sub 2}O{sub 3}-matrix interfaces had an incomplete layer of a silicon-rich amorphous phase. Preferential attack of the particles during sintering is believed to cause the crystallographic facets to form on SiC. Locally high silicon concentrations near Al{sub 2}O{sub 3} particles led to the formation of a glassy phase from the reduction of Al{sub 2}O{sub 3}. The difference in interfacial structure resulted in a higher particle-matrix bond strength and therefore improved composite mechanical properties in the SiC-reinforced materials ...

British Library Electronic Table of Contents (United Kingdom)

Strut lattice structures of reaction-bonded silicon infiltrated silicon carbide ceramics (RB-SiSiC) for air-fuel mixture formation and for nonstationary lean-burn under pressure applications were fabricated. The lattice design with a high porosity >80% was shaped by indirect three-dimensional printing. It was shown that pre-ignition processes in the porous reactor are much faster than in a free combustion, especially at lower temperatures. Interaction of high velocity diesel jets with cylindrical strut ligaments of the SiSiC lattice structure offers a new possibility for quick and efficient fuel distribution (multi-jet splitting) in space.

International Nuclear Information System (INIS)

Modern day accelerator development encompasses a myriad technologies required for their diverse needs. Whereas RF, high voltage, vacuum, cryogenics etc., technologies meet their functional requirements, high finish lapping processes, ceramic-metal joining, oven brazing, spark erosion or wire cutting etc., are a must to meet their fabrication requirements. Electromagnetic (EM) forming technique falls in the latter category and is developed as a special technology. It is currently catering to the development as a nuclear reactor technology, but has the potential to meet accelerator requirements too. This paper highlights the general principle of its working, simple design guidelines, advantages, and suggests some specific areas where this could benefit accelerator technologies

Science.gov (United States)

A system for inspecting a ceramic component. The ceramic component is positioned on a first rotary table. The first rotary table rotates the ceramic component. Light is directed toward the first rotary table and the rotating ceramic component. A detector is located on a second rotary table. The second rotary table is operably connected to the first rotary table and the rotating ceramic component. The second rotary table is used to move the detector at an angle to the first rotary table and the rotating ceramic component.

Energy Technology Data Exchange (ETDEWEB)

In order to apply chemical-looping combustion to a practical power plant, carbon deposition on the solid particle is one of the key problems to be overcome. Six kinds of solid particles were examined to clarify the kinetic behavior of carbon deposition. The effects of the solid composition, feed gas composition, and reaction temperature on carbon deposition were investigated by thermogravimetrical reactor on the basis of NiO/YSZ particle. From the viewpoints of both reactivity and resistance against carbon deposition, the particle of NiO mixed with YSZ (i.e., yttria-stabilized zirconia) was found to be a good candidate for chemical-looping combustion. It has been observed that carbon deposition could be completely avoided with very low concentration of water vapor. By means of a proposed model, the condition that carbon deposition would be avoided was identified. 12 refs., 8 figs., 2 tabs.

British Library Electronic Table of Contents (United Kingdom)

The coal-derived gas from a coal gasifier contains multiple contaminants, and their synergistic effects may not be simply the additive influences of individual contaminants. The present work presents the results of a study of the synergistic effects of four contaminants of major concern-S, As, P, and Cl, at the ppm level and in combinations of two, three, or four kinds-on the performance of Ni-YSZ/YSZ/LSM solid oxide fuel cells. The results indicate that both cell performance and morphology differ significantly in cells exposed to a single contaminant, and that cell performance is not simply the additive influence of each contaminant. Synergistic effects can be very destructive (accelerated degradation or even cell failure) when S is in the presence with As/P, but can also be beneficial (s...

International Nuclear Information System (INIS)

Most countries have taken the vitrification route for managing High Level Waste (HLW). Depending on composition of site-specific HLW, suitable glass forming oxides are added to it in a melting furnace designed for converting the mixture to a matrix of borosilicate glass. After thorough homogenization, the product is poured into stainless steel canisters as an inert solidified form. Canisters are seal welded and 2-3 such containers are then packed and sealed in another bigger container for providing an additional engineered barrier. This product form is considered safe for long-term storage. The concurrent vitrification technologies employ either induction-heated metallic melters or joule-heated direct resistance-heated ceramic melters. In India, both technologies have been adopted. While older facilities in Trombay and Tarapur employ metallic melters, a retrofitted facility at Tarapur and the new plant at Kalpakkam are based on ceramic melter ...

Science.gov (United States)

... The data were transformed into total hemispherical emittance values and correlated with respect to ceramic coating thickness and temperature ...

CERN Document Server

Fabrication of an infrared bolometer with a high T$_{c}$ superconducting thermometer

Energy Technology Data Exchange (ETDEWEB)

High-spatial-resolution microfocus-based X-ray imaging technology, both real-time and film, has been used to study the thickness variation that occurs in the oxide core of silver-sheathed BSCCO ribbons produced by the powder-in-tube method. This thickness variation (also called ``sausaging``) occurs during incremental rolling and degrades the critical current densities of the ribbons. Using X-ray image data the authors determined the onset and severity of sausaging. Onset occurred at a ribbon thickness of 203 {micro}m, and the severity increased with subsequent rolling reductions. Scanning electron microscopy was used to confirm the X-ray image data. X-ray imaging provides several advantages over more traditional methods for characterizing the superconductors such as optical or scanning electron microscopy. The X-ray imaging provides nondestructive information about the entire width of the ribbon, with far greater speed, lower cost, and more flexibility than the traditional techniques.

Energy Technology Data Exchange (ETDEWEB)

The information reported is for the period October I to December 31, 1993. During this quarter, activities were undertaken in Task 2. Oxygen concentrations were measured in the post-flame region of the entrained flow reactor. The sampling probe was used for the hot gas tests to sample the gas stream. Samples were injected into a gas chromatograph to determine the oxygen concentration. Results agreed with thermoequilibrium calculations that yield equilibrium compositions based on the stoichiometry of the feed gases. The axial temperature distribution along the reactor centerline was measured using a silica-coated platinum-rhodium thermocouple. Two coating techniques were tested and it was found that flame-plating silica to the thermocouple wires produced a thinner coating than a ceramic adhesive technique and therefore a smaller radiation correction. Other activities this quarter included the fabrication of a solids sampling probe support ...

Wastenet

... 300710+Ceramic+Transactions+Series 2120%28Series+Code%29+Ceramic+Transactions+Series Wiley::Ceramic Transactions Series WILEY KNOWLEDGE FOR GENERATIONS United States Change Location Home ...CART | MY ACCOUNT | CONTACT US | HELP Home / Engineering & Materials Science / Materials Science / Ceramic Transactions Series Related Subjects Soft Matter Organic Electronics Structural Materials, ... Ceramics Structural Materials, Composites Structural Materials or Construction Materials Corrosion Electronics Materials Related Series Ceramic Engineering and Science Proceedings Wiley Series in Materials ...for Electronic and Optoelectric Applications Ceramic Transactions (CTs) books contain papers presented at the Annual Meeting of the American Ceramic Society, ...

International Nuclear Information System (INIS)

Large, complex, high purity ceramic shapes are required by a variety of emerging technologies for their electrical insulation and high temperature strength properties coupled with their refractoriness and purity. Ceramic sealant bonding, using crystalline and vitreous sealant materials, has recently shown significant potential for joining technical ceramics to form the required shapes. Materials and techniques for joining technical ceramics including alumina, magnesia, zirconia and thoria are discussed. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The Externally-Fired Combined Cycle (EFCC) is an attractive emerging technology for powering high efficiency combined gas and steam turbine cycles with coal or other ash bearing fuels. In the EFCC, the heat input to a gas turbine is supplied indirectly through a ceramic air heater. The air heater, along with an atmospheric coal combustor and ancillary equipment, replaces the conventional gas turbine combustor. A steam generator located downstream from the ceramic air heater and steam turbine cycle, along with an exhaust cleanup system, completes the combined cycle. A key element of the EFCC Development Program, the 25 MMBtu/h heat-input Kennebunk Test Facility (KTF), has recently begun operation. The KTF has been operating with natural gas and will begin operating with coal in early 1995. The US Department of Energy selected an EFCC repowering of the Pennsylvania Electric Company`s Warren Station for funding under the Clean Coal Technology ...

International Nuclear Information System (INIS)

Highly conductive biaxially textured RuO_2 thin films were deposited on technically important SiO_2/Si substrates by pulsed laser deposition, where yttria-stabilized zirconia (YSZ) produced by ion-beam-assisted-deposition (IBAD) was used as a template to enhance the biaxial texture of RuO_2 on SiO_2/Si. The biaxially oriented RuO_2 had a room-temperature resistivity of 37 #mu##OMEGA#-cm and residual resistivity ratio above 2. We then deposited Ba_0_._5Sr_0_._5TiO_3 thin films on RuO_2/IBAD-YSZ/SiO_2/Si. The Ba_0_._5Sr_0_._5TiO_3 had a pure (111) orientation normal to the substrate surface and a dielectric constant above 360 at 100 kHz. copyright 1998 Materials Research Society.

Science.gov (United States)

A novel reactor combining a flame-deposited nanostructured titanium dioxide film and a set of embedded ceramic electrodes was designed, developed and tested for degradation of methyl tert-butyl ether (MTBE) in water. On applying a voltage to the ceramic electrodes, a surface coro...

Science.gov (United States)

Courses in Ceramic Engineering from the Course Catalog at the University of Illinois at Urbana-Champaign. List includes: CER E 299. Senior Thesis CER E 320. Ceramic Materials and Properties CER E 321. Ceramic Processing and Microstructure Development CER E 322. Process Design CER E 323. Ceramic Engineering Processing Laboratory CER E 324. Refractory Technology CER E 326. Chemistry and Technology of Glass CER E 327. Ceramic Microscopy CER E 328. Electrical Ceramics CER E 330. Chemically Bonded Ceramics CER E 390. Special Topics in Ceramics CER E 420. Ceramic Chemistry CER E 422. Dielectric Properties of Ceramic Materials CER E 425. Physical Chemistry of Clays and Soils CER E 426. Mineralogy of Clays CER E 427. Petrology of Clay Minerals CER E 429. Seminar in ...

Energy Technology Data Exchange (ETDEWEB)

Out of the R and D of mesoscopic metal group composite materials, the paper described the fiscal 1997 results. In the in-situ method as a composite material making method, elucidated to some degree were chemical composition of Fe-C-Cr-V-Nb-Mo-W-Ni base multi-dimensional alloys, and wear resistance and oxidation resistance of MC type carbide dispersion multi-phase texture crystallizing as primary crystal and eutectic. In the composite material making with ceramic fiber and alloy by the pressure infiltration method, the paper clarified the texture formation mechanism in solidification/heat treatment by a combination of Al alloys and alumina long fiber, and the relation between fiber configuration and wear resistance. By MA and MG methods as the powder metallurgy composite material making method, a composed body of {alpha}-stainless steel of Fe-12%Cr composition and M23C6 of 40-90vol% are designed for alloy composition, and powder of amorphous or hyperfine texture was ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Stress relaxation was studied at 408 K on AZ31 reinforced by ceramic foam produced by in situ foaming of filler loaded preceramic polymer melt. Reinforcement causes significant enhancement of the resistance against stress relaxation compared to AZ91. It is correlated with hardening by the ceramic skeleton as well as ceramic particles formed in the AZ31-matrix. (orig.)

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

Science.gov (United States)

Website hosted by the American Ceramics Society with history of ceramics education, along with notable ceramic engineering educators. "In May 1894, two rooms in the basement of The Ohio State University?s College of Engineering were set aside to create a new department: Clay-Working and Ceramics. Founded with a $10,000 grant from the State of Ohio, the department was the first of its kind anywhere in the nation. The course of study was the idea and personal project of Edward Orton Jr., a young mining engineer. Orton had gathered his ceramic knowledge, piece by piece, from various jobs in coalmines, glass factories and steel plants. In 1893 he was the superintendent for a factory that made paving bricks. Orton?s factory, hit by an ?acute crisis,? closed, leaving him with some unexpected extra time. He used the opportunity to lobby for the passage of what some people dubbed the ?Mud ...

British Library Electronic Table of Contents (United Kingdom)

The percolated or active triple phase boundary (TPB) length per unit volume of Ni-YSZ anode hollow fibers (HFs) containing 60wt.% initial NiO and a spatially varying microstructure were measured using a focused ion beam (FIB)-SEM technique. The measured values of contiguous TPB density were interfaced with a 2-D distributed finite element model of a hollow fiber solid oxide fuel cell. The model was applied to simultaneously solve the ionic and electronic charge balances in the electrodes, which were modelled as overlying continuum materials with effective electronic and ionic conductivities. The model was used to predict the effects of anode microstructure on the distribution of current density, and anode activation polarization. Active TPB lengths of 2.63-8.63 m^-^2 were measured for the ...

Energy Technology Data Exchange (ETDEWEB)

In support of the efforts to apply ceramics to advanced heat engines, a study is being performed of the performance of ceramics at the ring/cylinder interface of advanced (low heat rejection) engines. The objective of the study, managed by the Oak Ridge National Laboratory, is to understand the basic mechanisms controlling the wear of ceramics and thereby identify means for applying ceramics effectively. Attempts to operate three different zirconias, silicon carbide, silicon nitride, and plasma-sprayed ceramic coatings without lubrication have not been successful because of excessive friction and high wear rates. Silicon carbide and silicon nitride perform well at ambient temperatures with fully formulated mineral oil lubrication, but are limited to temperatures of 500F because of the lack of suitable liquid lubricants for higher temperatures.

Energy Technology Data Exchange (ETDEWEB)

Ceramic ball bearings of silicon nitride are used for hard disk drive (HDD) spindle motors, to increase seed, reliability and memory capacity of the HDDs. Silicon nitride ceramics have advantages of lightweight, high strength and hardness over the conventional steel for bearings, but is expensive. A new process of high cost performance has been developed for mass production of the small-size ceramic balls. The company plans to apply these bearings to higher devices, e.g., servers, for the time being, and to expand the applicable areas, e.g., common devices and other small-size motors. The ceramic bearings have been developed jointly with Koyo Seiko Co. Ltd. (translated by NEDO)

International Nuclear Information System (INIS)

We have investigated the growth behaviors of high temperature compatible ZrO_2 insulation coatings on Ag and AgMg sheathed Bi_2Sr_2Ca_1Cu_2O_x superconducting tapes depending on number of dipping and thermal conditions. The coatings were fabricated on long-length superconducting tape substrates using a solution derived from Zr tetrabutoxide, solvent and chelating agent for high magnetic field magnets. The layer-on-layer growth behaviors were characterized by environmental scanning electron microscope (ESEM), energy dispersive spectroscopy (EDS), X-ray maps and X-ray diffraction (XRD). This research showed that the ZrO_2 coatings were regularly grown on Ag-based tape substrates and coating thickness increased with increasing number of dipping. It was found that ceramic oxides formed at temperature range 450 and 550 deg. C. The final coating thickness changed between 6 and 8 #mu#m after annealing process. Resistance of insulation measured from ...

British Library Electronic Table of Contents (United Kingdom)

(1-x)(Na0.5K0.5)NbO3-xAgSbO3 lead-free piezoelectric ceramics were prepared by normal sintering. The effects of the AgSbO3 on the phase structure and piezoelectric properties of the ceramics were systematically studied. These results show that the AgSbO3-modified (K0.50Na0.50)NbO3 lead-free piezoelectric ceramics form stable solution with orthorhombic structure, and the Curie temperature and the polymorphic phase transition of the ceramics decreased with increasing AgSbO3. The result shows that the piezoelectric properties of the ceramics strongly depend on the AgSbO3. The ceramics with x=0.05 possess optimum properties (d33=192 pC/N, kp=43%, Tc=348degreeC, To-t=145degreeC, ?r632, and tan d3.5%). These results indicate that the ceramic is a promising candidate material for lead-free piezoe...

International Science & Technology Center (ISTC)

Development of New Resource-Saving Technologies for Ceramic Material Production: High resistant Pigments, Heat Shielding, Plasters, Filters, etc.; by the Method of Controllable Thermosynthesis in Combustion Wave Using Industrial Metal-Containing Wastes

International Nuclear Information System (INIS)

English 2006 2 p. Brazil Rocha, RM Centro Tecnico Aeroespacial, Sao

Science.gov (United States)

Sensitivity to Dental Cements; Dental Crowns; Dental Three-unit Bridges

Science.gov (United States)

PMID:21846114

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Suspension direct current plasma spraying allows achieving finely structured coatings whose thickness is between few tens and few hundreds of micrometres. Drops (200-300 ?m in diameter) or liquid jets are mechanically injected in the plasma jet. With radial injection they are rapidly (a few ?s) fragmented into droplets (a few ?m in diameter). The latter are vaporized (in a few ?s) and the solid particles contained in suspension droplets are accelerated and melted by the plasma jet. As in conventional plasma spraying (CPS), much smaller splats (with diameters between 0.2 and 3 ?m and thicknesses between 30 and 200 nm) are arranged in layers up to form the coating. The low inertia of particles requires spray distances between 40 and 60 mm which induces plasma heat fluxes up to 22 MW m-2 participating in coating densification. Even more than in CPS, the plasma jet fluctuations, particularly for plasmas containing di-atomic gases, perturb drops penetration and fragmentation. It has been ...

Energy Technology Data Exchange (ETDEWEB)

The addition of titanium to eutectic braze compositions causes these alloys to readily wet and bond to A1N ceramics. Electron microscopic characterizations of the metal-ceramic interfaces reveal the presence of TiN, along with other Ti- and Al-containing phases. The formation of such interfacial reaction products is an additional thermodynamic driving force for the creation of useful metal-ceramic bonds. 12 refs., 4 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

The ceramic composite armor has been lucubrated in the past 40 years. Ceramic can provide the same protection as metal, but it has lighter weight than metal. Ceramic has excellent ability of resisting kinetic energy projectile, because it can transfer energy to a large range by its fragmented cone and has higher ability of eroding the projectile than metal. But the researches indicated the full potential of the ceramic hard face has not been achieved because the significant interface between ceramic and metal has the unfavorable impedance effects and would induce tensile failure. FGM is a new type composite with continuous transition from ceramic to metal; it has no significant discrete materials interfaces between ceramic and metal. This paper deals with the impact response of Ceramic/FGM/Metal armor by numerical and ...

Energy Technology Data Exchange (ETDEWEB)

The development and experimental demonstration of a high-temperature seal for the SHARE ceramic dome cavity receiver is reported. The mechanical contact seal which was tested on one-foot-diameter silicon-carbide ceramic-dome hardware at pressure differentials to four atmospheres and dome temperatures to 2200/sup 0/F (1200/sup 0/C) showed negligible leakage at expected receiver operating conditions. Potential solar receiver applications for the technology are illustrated.

Science.gov (United States)

The use of ceramics as energy absorbents has been studied by many researchers and some improvements in the ballistic performance of ceramic tiles have been made by coating them with different classes of materials (e.g. E-glass/epoxy, carbon-fiber/epoxy, etc.). Using ceramics for energy absorbing applications leads to a significant weight reduction of the system. Therefore, any modification to the ceramic configuration in the system which leads to more energy absorption with the same or less areal density is significant. On the other hand, polyurea has been proved to be an excellent energy dissipating agent in many applications. Inspired by this, we are studying the effect of coating ceramics with polyurea and other materials, on the energy absorption and ballistic performance of the resulting ceramic-based composites. In this study, we investigate the effect of ...

Energy Technology Data Exchange (ETDEWEB)

Woven Kevlar fabrics exhibit a number of beneficial mechanical properties which include strength, flexibility, and relatively low density. The desire to engineer or design Kevlar fabrics for specific applications has stimulated interest in the development of theoretical models which relate their effective mechanical properties to specific aspects of the fabric morphology and microstructure. In this work the author provides a theoretical investigation of the large deformation elastic response of a plane woven Kevlar fabric and compares these theoretical results with experimental data obtained from uniaxially loaded Kevlar fabrics. The theoretical analysis assumes the woven fabric to be a regular network of orthogonal interlaced yarns and the individual yarns are modeled as extensible elastica, thus coupling stretching and bending effects at the outset. This ...

British Library Electronic Table of Contents (United Kingdom)

Statement of problem The opacity of the metal framework in metal ceramic restorations results in reduced light transmission through the tooth that diminishes the esthetics of the tooth. Purpose The purpose of this study was to investigate the color change that occurs apically to a metal ceramic restoration as a result of altering the metal framework design. Material and methods Color change relative to the unprepared tooth (DE) between various metal ceramic restorations was determined using computer imaging and CIELAB coordinates and compared to previously determined levels of clinical acceptability. Color change was evaluated by examining 2 conditions (the metal copings and the completed metal ceramic restorations), 4 framework designs (metal collar and porcelain margins with 0-mm, 1-mm, ...

Energy Technology Data Exchange (ETDEWEB)

Resulting of the remarkably growth on economical development in each countries of Asia, ceramics low heat rejection engines are paid attention as a technique corresponding with the third oil shock which is presumed in near future. On the other hand, in order to construct the low heat rejection engines, using the quite different property materials from metals which called ceramics, it is necessary to determine design and combustion method fitted to the feature of this different kind materials. Though the development of ceramics low heat rejection engines have been given up in the world, recently, the development of ceramics engines is again required for the purpose of realizing an engine with low fuel consumption. Authors have successfully solved the problems, such as the disuse of cooling system, the improvement of combustion to reduce fuel consumption and exhaust emissions, and the realization of ...

International Nuclear Information System (INIS)

A suspension-firing type radioactive waste incineration system is developed and cold demonstration testing of ceramic filters for the system are carried out. The incineration system, which is useful for a wide variety of waste materials, can serve to simplify the facilities and to reduce the costs for waste disposal. The incineration system can be used for drying-processing of concentrated waste liquids and disposal of flame resistant materials including ion exchange resins and rubber, as well as for ordinary combustible solid materials. An on-line backwash system is adopted to allow the ceramic filters to operate stably for a long period of time. For one-step filtering using the ceramic filter, the decontamination factor is greater than 10"5 for the processing of various wastes. In a practical situation, there exist vapor produced by the spray drier and the cladding in used ion exchange resin, which act to increase the ...

Science.gov (United States)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... Descriptors : *PROPELLING CHARGES, *NITROCELLULOSE, *COMBUSTIBLE CARTRIDGE CASES, DENSITY, FIBERS, MANUFACTURING ...

Energy Technology Data Exchange (ETDEWEB)

We provide a detailed overview of an ongoing, multinational test program that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolized materials plus volatilized fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high energy density device, HEDD. The program participants in the U.S. plus Germany, France, and the U.K., part of the international Working Group for Sabotage Concerns of Transport and Storage Casks, WGSTSC have strongly supported and coordinated this research program. Sandia National Laboratories, SNL, has the lead role for conducting this research program; test program support is provided by both the U.S. Department of Energy and Nuclear Regulatory Commission. WGSTSC partners need this research to better understand potential radiological impacts from sabotage of nuclear material shipments and storage casks, and ...

International Nuclear Information System (INIS)

Full text: Dissolution test (DT) is one of the important specifications of PFBR MOX fuel. It is a macro homogeneity test used to ascertain that the dissolution of spent fuel will be easier during reprocessing. The DT specification limit for PFBR MOX fuel is ? 1.0 wt.% residue of the whole pellet when it is dissolved in HNO3 under reflux conditions. For this test, sintered MOX pellet is dissolved in reflux condition in 60 ml of 12M HNO3 for 10 hours. This test is carried out for each batch and during complete MOX campaign a lot of MOX waste in liquid form is being generated. This liquid waste is in clean form and U and Pu is required to be recovered from the clean waste. Different methods like direct denitration, precipitation and solvent extraction are available but either the product is not of good quality for pelletization or secondary liquid wastes are generated. Microwave denitration is a faster and cleaner method which has different heat transfer mechanism and temperature profile ...

Energy Technology Data Exchange (ETDEWEB)

This book describes the uses, coatings, and fabrication of laser materials. Topics considered include: optical waveguide materials; optical storage materials; holographic recording materials; phase conjunction materials; holographic recording materials; phase conjunction materials; laser crystals; laser glasses; quantum counter materials; thin films and coatings; multilayer dielectric coatings; graded-index surfaces and films; optical materials fabrication; fabrication techniques; fabrication procedures for specific materials.

British Library Electronic Table of Contents (United Kingdom)

Abstract Many (K1-xNax)NbO3 (KNN)-based ceramics with high piezoelectric performance exhibit undesirable strong temperature dependence due to the orthorhombic-tetragonal polymorphic phase transition near room temperature. In order to improve the temperature stability of the ceramics, many additives have been added into the KNN-based ceramics to shift TO-T down to below room temperature. Contrary to the previous approach (Na0.53K0.47-xAgx)Nb1-xSbxO3 (NKANS) ceramics with TO-T well above room temperature have been prepared by a conventional solid-state reaction method. The density and the electrical properties are effectively improved by the addition of AgSbO3, and optimum piezoelectric properties are found in the ceramics with 0.05---x---0.07, with maximum kp---0.46 for NKANS5 and maximum d...

International Nuclear Information System (INIS)

SiAlONs are ceramics with high potential as biomaterials due to their chemical stability, associated with suitable mechanical properties, such as high fracture toughness and fracture resistance. The objective of this work was to investigate the mechanical properties and the cytotoxicity of these ceramic materials. Three different compositions were prepared, using silicon nitride, aluminum nitride and a rare earth oxide mixture as starting powders, yielding Si_3N_4-SiAlON composites or pure SiAlON ceramics, after hot-pressing at 1750 deg. C, for 30 min. The sintered samples were characterized by X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM). Furthermore, hardness and fracture toughness were determined using the Vicker's indentation method. The biological compatibility was evaluated by in vitro cytotoxicity tests. Ceramic with elevated hardness, ranging between 17 and 21 GPa, and ...

International Nuclear Information System (INIS)

Study results on long-term thermal and corrosion resistance of packs with electro-insulation layer of aluminium nitride are presented. Structural changes of nitride ceramics and contact zones between metal and ceramics are considered. It is shown that multilayer metallo-ceramic packs, manufactured by gas-phase technology have high electro- and thermophysical properties, high thermal and corrosion resistance relative to cesium vapor, vacuum density as well as high thermo-resistance. 8 refs., 4 figs.

International Nuclear Information System (INIS)

Monolithic SiAlON ceramics are hard and brittle with little possibility for property design, but multi-phase SiAlON ceramics offer great scope for controlling microstructural development and desired properties. The ceramics can also be reinforced by separate additions of other hard, refractory compounds. The toughness in all these SiAlON composites can be increased by several mechanisms, and the best effect is reached if they are combined. When glassy phase is present, crack paths are affected by the strains caused by different thermal expansion of the glassy phase and the crystals and also by the interface properties. The crystal shape influence toughness, especially pronounced is the effect of the elongated #beta#- grains. Different toughening mechanisms are achieved by separately added reinforcement phases. The hardness is raised by the presence of #alpha# SiAlON and other hard constituents, such as SiC. (orig.).

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

In the present study, element interdiffusions at the cofired interface of 9/1 Ag/Pd electrode and lead magnesium niobate (PMN)-based ferroelectrics were investigated using Auger Electron Spectroscopy (AES). Intense interdiffusions at the interface were observed while Ag and Pd could penetrate into the ceramics for about 1 {mu}m. Ag-doping experiments were carried out to further study the effects of Ag diffusion on electrical properties of the ceramics. The results showed that Ag could be incorporated into solid solution of the ceramics as Ag{sup +}. As a whole, the Curie temperature (Tc) and dielectric constant of the ceramics decreased with Ag addition. However, Ag addition had no obvious effect on the insulation resistivity. The results inferred that Ag{sup +} could substitute for Pb{sup 2+} at A site of ABO{sub 3} lattice, thereby oxygen vacancies were generated.

International Nuclear Information System (INIS)

Turkish English ... Authors Sahin, O. (Suleyman Demirel University, Department of Physics, Isparta (Turkey))

British Library Electronic Table of Contents (United Kingdom)

Objective.The interest of dental research in metal-free restorations has been rising in the last 20 years following the introduction of innovative all-ceramic materials in the daily practice. In particular, high strength ceramics and related CAD/CAM techniques have widely increased the clinical indications of metal-free prostheses, showing more favourable mechanical characteristics compared to the early ceramic materials.The purpose of the present paper is providing a brief review on the all-ceramic dental materials, evaluating pros and cons in the light of the most recent scientific results and of the authors? clinical experience.Materials. A structured review of the literature was given on the basis of medical and engineering papers published in the last decades on the use of dental cera...

International Nuclear Information System (INIS)

A survey is presented of the principles and practice of tailoring sintering liquid composition and processing cycle to enable crystallisation of intergranular phases in silicon nitride and sialon ceramics. Critical features in sialon ceramics are the O/N balance in residual glasses and post-sintering heat-treatment temperatures to enable nucleation of either intermediate phases at constant composition or oxide phases with re-partitioning of non stoichiometric components in #beta#' or #alpha#' solid solutions. Crystallisation of disilicate phases in non-sialon compositions exemplifies a problem in control of polymorphs with differing atomic volumes. Crystallisation of intergranular phases has an influence mainly on high-temperature mechanical and environmental behaviour of these ceramics. (orig.).

Science.gov (United States)

... 1. Reeber, RR, Kusy, RP, Yu, N. and Chu, WK " Formation of a Solid Lubricant in Boron Carbide by Nitrogen Ion Implantation and Laser Annealing ...

Science.gov (United States)

Description of courses, curriculum and degree program. "Ceramic and materials engineers design, develop, and participate in the manufacture of both standard and new materials intended for use in a wide variety of industries with diverse applications. These range from the semi-conductor to the aerospace and finally to the traditional ceramics industry. The broad scope of industrial responsibilities handled by ceramic and materials engineers requires knowledge in mathematics, science, engineering, and the social sciences, skills in problem solving, engineering analysis, design, and written and oral communication. The baccalaureate program integrates laboratory with classroom experiences to prepare students for life-long learning. Courses covering thermodynamics, kinetics, mechanical behavior, processing and characterization of materials prepare students for careers in industry and/or for graduate school. Clemson University ...

UK PubMed Central (United Kingdom)

We demonstrate rapid fabrication of submicrometer-diameter pores in borosilicate glass using femtosecond laser machining and subsequent wet-etch techniques. This approach allows direct and repeatable...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The diffusion of alkali vapours in the anode compartment of a DIR-MCFC produces the deactivation of the internal reforming catalyst. Sets of ceramic porous membranes purposed to limit the diffusion have been manufactured by different techniques and the influence of the preparation technique and of the preparative variables on the morphological characteristics of the membranes structures has been studied.

Energy Technology Data Exchange (ETDEWEB)

The peculiarities of pulsed laser melting and evaporation of the superconducting ceramics are analyzed by means of numerical simulation. The appearance of the overheated metastable states in solid and liquid phases is shown as a result of the phase front dynamics and volume nature of laser energy release. A method of dynamic adaptation for the multifront Stefan problem is proposed.

Energy Technology Data Exchange (ETDEWEB)

According to the present invention, a joined product is at least two ceramic parts, specifically bi-element carbide parts with a bond joint therebetween, wherein the bond joint has a metal silicon phase. The bi-element carbide refers to compounds of MC, M.sub.2 C, M.sub.4 C and combinations thereof, where M is a first element and C is carbon. The metal silicon phase may be a metal silicon carbide ternary phase, or a metal silicide.

Science.gov (United States)

A new dual focal point electro-optic lens that is switchable to focusing and unfocusing is proposed and successfully demonstrated. This electro-optic lens is constructed by coating transparent fine electrodes in the Fresnel-zone plate onto a PLZT ceramic plate. Its focal length changes from 1.25 m to infinity binary at 515 nm with the external voltage of 210 V. PMID:20725208

Energy Technology Data Exchange (ETDEWEB)

This document contains a listing of the written scientific information originating in the Materials Joining Group (formerly the Welding and Brazing Group), Metals and Ceramics Division, Oak Ridge National Laboratory during 1951 through June 1987. It is a registry of about 400 documents as nearly as possible in the order in which they were issued.

Science.gov (United States)

... spatially defined fashion. Many surface modification techniques require a sequential chemical treatment of the surface.6 ...

International Nuclear Information System (INIS)

The use of a selective epitaxial growth technique for fabricating YBCO thin-film microstructures is described. No film post-deposition processing is required; hence damage to the structure is minimized. The technique is compatible with a passivation process to protect the structure without exposure to air. The microbridges, Josephson junctions and rf SQUIDs protected by an amorphous YBCO passivation have long lifetime even after severe accelerated aging tests. Rf SQUIDs fabricated by this technique show a significant reduction of low-frequency noise when operating in weak magnetic fields compared with SQUIDs fabricated by the conventional ion beam etching technique. (author)

Science.gov (United States)

... Development Tapered Roller Bearing Program . . . 11 ... 98 61 Tapered Roller Bearing Component t Identification..... 104 ...

Energy Technology Data Exchange (ETDEWEB)

There are a number of characteristics exhibited by ceramic materials that may provide potential benefits for the reciprocating internal combustion engine. However, the brittle nature of these materials together with a variability in strength has created difficulties in applying ceramic materials to the engine environment. Although a wide range of physical properties is available from contemporary ceramic materials, a material offering consistently high strength has yet to be developed. For sliding-contact applications, desirable characteristics include good wear resistance, low friction, ability to join metals and good heat dissipation. Test results have shown that cam/follower components with cast iron cam sliding on a silicon nitride follower exhibit very low wear rates. The application of silicon carbide to face seals has also shown substantial reductions in both friction and wear when compared with conventional ...

Energy Technology Data Exchange (ETDEWEB)

Sintered glass-ceramics were produced from coal fly ashes, red mud from aluminum production and silica fume. The capabilities of Tuncbilek fly ash and a mixture of Orhaneli fly ash, red mud and silica fume to be vitrified and devitrified by sintering process were investigated by means of scanning electron microscopy and X-ray diffraction analysis. To determine the effect of binder in the sintering technique, glass powders were pressed without or with the addition of polyvinyl alcohol. Owing to microstructural observations, density and hardness measurements, it can be said that physical properties and the hardness of the produced samples strongly depended on the crystallization degree of the samples. Toxicity characteristic leaching procedure test results showed that glass-ceramic samples produced by using sintering technique could be considered as nonhazardous materials. Chemical durability of the sintered glass-ceramic ...

International Nuclear Information System (INIS)

The authors observed an extremely high permittivity (#approx#35 000 at T_C) in barium zirconate titanate (BaZr_0_._1Ti_0_._9O_3) ceramics with holmium substitution (1-5 mol %) in Ba site. Careful microstructural investigation and energy dispersive spectroscopy analysis of the 1-2 mol % of Ho substituted ceramics showed the enrichment of a Ho-phase along the grain boundaries with a composition close to the Ho_2Ti_2O_7 pyrochlore. The formation of Ho rich phase resulted in the Maxwell-Wagner polarization mechanism, which leads to this unusually high permittivity. Ceramics with 3 mol % or higher Ho content showed lesser permittivity values compared to 1-2 mol %, probably due to the increase in pyrochlore phase. These high dielectric constant ceramics are useful in nanoscale devices.

Energy Technology Data Exchange (ETDEWEB)

Ceramic antifriction bearings were introduced in excellent characterics and application. In main shaft use bearings of the machine tool, to be heightened in efficiency and accuracy by the heightening in speed, centrifugal load to the outer ring is not negligible to shorten the bearing in life. Also ball bearings with a contact angle are easily corroded by a very strong revolution slide due to the gyromoment. The use of such light weight material as silicon nitride's can design the lengthening in life. Also the utilization of high rigidity can prevent the inner ring from expanding by centrifugal force and enable the machining to be with a high accuracy. Ceramic rolling element is excellent also in backing resistant property and effective on the oily film cut. With heat resistant property, it maintains hardness even at high temperature. Such excellent characteristics being utilized, the fine ceramic antifriction ...

International Nuclear Information System (INIS)

Advanced structural ceramics are presently used in several tribological applications, such as precision instrument bearings, automotive engine parts and cutting tools inserts. Design and selection of advanced ceramics for these applications require reliable data on the effects of temperature, load and environment on the tribological behaviour of these materials. In the present work, the friction and wear behaviour of colloidally processed and pressureless sintered sialon ceramics with phase (#alpha#) have been studied, aiming at increasing #alpha#-sialon in industrial applications as cutting tools. The friction and wear behaviour of sialon ceramics against steel DIN-Ck45K were investigated using a pin-on-disk tribometer under dry sliding conditions at room temperature, in order to eliminate the contribution of lubricant. The experiments were performed with a constant sliding velocity of 0.5 m/s and a ...

Energy Technology Data Exchange (ETDEWEB)

Ti honeycombs with the side of 800 and 400 nm were fabricated by focused ion beam (FIB), though the surfaces of the bottom and wall of the Ti honeycombs were rough, as compared with the surfaces of the bottom and wall of the Si honeycomb. It is demonstrated that the nanoscale Ti components can be fabricated in a short time by FIB.

Energy Technology Data Exchange (ETDEWEB)

The US National Energy Policy of 2001 advocated the development of advanced fuel and fuel cycle technologies that are cleaner, more efficient, less waste-intensive, and more proliferation resistant. The need for advanced fuel development is emphasized in on-going DOE-supported programs, e.g., Global Nuclear Energy Initiative (GNEI), Advanced Fuel Cycle Initiative (AFCI), and GEN-IV Technology Development. The Directorates of Energy & Environment (E&E) and Chemistry & Material Sciences (C&MS) at Lawrence Livermore National Laboratory (LLNL) are interested in advanced fuel research and manufacturing using its multi-disciplinary capability and facilities to support a design concept of a small, secure, transportable, and autonomous reactor (SSTAR). The E&E and C&MS Directorates co-sponsored this Laboratory Directed Research & Development (LDRD) Project on Mono-Uranium Nitride Fuel Development for SSTAR and Space Applications. In fact, three out ...

Energy Technology Data Exchange (ETDEWEB)

The Partnership for a New Generation of Vehicles (PNGV) program intends to develop new designs for automobiles that will reduce fuel consumption by two thirds but otherwise have price, comfort, safety, and other measures of performance similar to the typical automobile now on the market. PNGV vehicle designs are expected to substitute lightweight materials, such as aluminum, magnesium, carbon-reinforced polymer composites, glass-reinforced polymer composites, and ultra- light steel, for heavier materials such as steel and iron in automobile components. The target mass of a PNGV vehicle is 1,960 pounds, as compared to the average current vehicle that weights 3,240 pounds. Other changes could include the use of different ferrous alloys, engineering changes, or incorporation of advanced ceramic components. Widespread adoption of these vehicle designs would affect materials markets and require concurrent development and adoption of supporting technologies to supply the ...

Energy Technology Data Exchange (ETDEWEB)

This work reports an alternative methodology for the linear attenuation coefficient determination ({mu} {rho}) of irregular form samples, in such a way that is not necessary to consider the sample thickness. With this methodology, indigenous archaeological ceramics fragments from the region of Londrina, north of Parana, were studied. These ceramics fragments belong to the Kaingaing and Tupiguarani traditions. The equation for the {mu} {rho} determination employing the two mean method was obtained and it was used for {mu} {rho} determination by the gamma ray beam attenuation if immersed ceramics, by turns, in two different means with known linear attenuation coefficient. By the other side, {mu} theoretical value was determined with the XCOM computer code. This code uses as input the ceramics chemistry composition and provides an energy versus mass attenuation coefficient table. In order to validate the ...

International Nuclear Information System (INIS)

Experimental results of compatibility tests on ceramics-metal bonded structures performed under high heat flux conditions in splash test apparatus are reported. Emphasis is placed on results of the channel wall design and its critical operating conditions under MHD environment. The module design of one cold type and three semihot type insulators have been tested. These materials were Al_2O_3, Al_2MgO_4, LaAlO_4, MgO and Sialon ceramics. The methods of cold type ceramics-metal bonding structure were studied on Al_2O_3 and Spinel spray coating technology. The refractory metallizing and ceramics-metal graded structure manufactured by HIP technologies were applied to bonding between the MgO or LaAlO_4 and metallic cooling system. The Sialon non-bonding structure was tested with mechanical supported cooling system by shrinc fitting method. The results indicated that the bonding structures made of the ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the basic principles underlying the operation of low heat loss engines and the magnitude of the efficiency improvements that are theoretically achievable. The effect of varying degrees of thermal insulation on various operating parameters is examined in some detail, as is the relationship between degree of insulation and ceramic coating thickness. The effect on ceramic materials of severe surface temperature oscillations and the resultant thermal stress gradients is also discussed. In the following section, the paper describes methods of construction adopted both for ceramic inserts and coatings, and rig tests for the assessment of thermal fatigue under both load and firing cycling. The paper does not attempt to draw any general conclusions.

British Library Electronic Table of Contents (United Kingdom)

Glass ceramics are commonly used as sealing materials for planar solid oxide fuel cells (SOFCs). The major requirements of stack and module builders for these materials are the stability of the coefficient of thermal expansion (CTE), excellent bonding (sticking) behaviour and the absence of volatile ingredients, which can lead to changes of the material properties and the sealing ability. SCHOTT Electronic Packaging has developed special glasses and glass-ceramics for various solid oxide fuel cell designs and operating temperatures. The glass compositions are based on the system MgO-Al2O3-BaO-SiO2-B2O3. In this study the evaluation of the developed materials was done by high temperature aging tests for up to 1000h, high temperature XRD-studies and Rietveld calculations, combined with scann...

Energy Technology Data Exchange (ETDEWEB)

The small pilot facility of a cyclone type suspension incineration system of radioactive waste was set up in order to evaluate the decontamination efficiency of a high efficiency ceramic filter. The evaluation was made by use of /sup 54/Mn, /sup 59/Fe, /sup 60/Co, /sup 65/Zn and /sup 137/Cs. 1. The decontamination factor by one line of ceramic filter for every species were over 10/sup 5/. 2. The decontamination factor increased by one oder when water vapor exists in off-gas. The same tendency was also observed when iron dioxide existed at the incineration of cation exchange resin.

Energy Technology Data Exchange (ETDEWEB)

The purpose of the invention is to improve a radiation receiver, consisting of a hollow body with an opening for the entry of radiation and a ceramic absorber situated in the hollow body, which absorbs the radiation energy entering through the opening, and emits it as thermal radiation to a heat medium, so that a higher efficiency can be achieved. According to the invention, the problem is solved by the fact that the absorber consists of ceramic material on the side towards the solar radiation, which has a low emission value and a high absorption value, and that the side of the absorber towards the heat medium has ceramic material of high emission value and low absorption value. This ensures that reradiation is prevented near the opening of the hollow body, and that the solar energy entering is largely absorbed in the hollow body.

Energy Technology Data Exchange (ETDEWEB)

The use of selective additives such as MgO as a sintering aid and a rare earth oxide as a grain growth inhibitor, has allowed the manufacture of beryllia ceramics having close to theoretical density. The grain size and grain size distribution can be controlled by an optimum firing schedule leaving a remnant porosity which is extremely fine (0.2 {mu}m). This structure is compared with conventional BeO ceramics, densified by liquid phase sintering, which develops a glassy grain boundary and retains large pores up to 3 {mu}m. The significantly improved strength properties, extremely fine pores,the 'pinning effect' of rare earth oxide, and the superior surface finish both in the as-fired and polished state are discussed in relation to the micro-structure. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Sintered glass-ceramics have been produced using municipal incinerator solid residues and glass cullet or an inert waste, from feldspars processing, as sintering aids. The capability of three different mixtures, either previously vitrified or not, to be sintered was investigated by means of linear shrinkage, water absorption and bulk density measurements, and by X-ray diffraction analysis and scanning electron microscopy observations. Particular attention has been addressed to the study of particle size effect on the sintering process. The conclusions that can be drawn from the experimental study are that the preliminary vitrification step is essential in order to obtain a dense sintered glass-ceramic product in the 850-1050 C temperature range developing silicate crystalline phases. The optimal powder particle size that confers a good densification degree was found to be < 45 {mu}m. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Statement of problem Even though metal ceramic restorations (MCRs) are widely used by clinicians, the influence of the metal on the color of overlaying porcelain is unknown. Purpose The purpose of this study was to analyze the color alterations of different types of metal ceramic alloys during several stages of metal surface preparation and to determine the effect of those changes on the resulting color of opaque porcelain (OP). Material and Methods Seven different types of alloys (3 base metal, 3 noble, and 1 high noble) were used to prepare disk-shaped specimens (1 mm x 10 mm, n=3), followed by OP application (0.1 mm). Lab values of specimens were recorded after different stages of metal surface preparation (ingot, after casting, after oxidation, and after the OP application) in addition...

International Nuclear Information System (INIS)

Different semi precious alloys (Pd-Ag, Pd-Au) have been studied after thermal oxidation treatments to analyze the mechanical improvement of the interface between the metal and the ceramic. Using the four point bending test, the authors have analyzed the different steps corresponding to the mechanical evolution of the bi-material : cracking energy on the surface, relaxation energy after first cracking, propagation energy of cracks at the interface zone. It has been shown that some alloys only have a high resistance to the interface cracking and the role played by the interface reactions to improve this property. (orig.).

Science.gov (United States)

was to mount Pd-Ag terminated MLCCs onto gold plated mounting pads of a ... to protect against incorrect shipment of pure tin-plated MLCCs when Pd-Ag ...

Energy Technology Data Exchange (ETDEWEB)

The development of turbine components for the automotive 100 kW ceramic gas turbine has entered the final stage of the seven-year project and is making satisfactory progress, toward the goals. The authors attained the interim targets of the aerodynamic performances and have been carrying out tests to further improve efficiency. As for ceramic parts, they have changed the material of the turbine rotor to a new one that is excellent in long-sustained and high-temperature strength properties, and have confirmed substantial strength at high temperature through hot-spin tests. After evaluating blade-vibration stress through analyses and experiments, the authors completed an endurance evaluation at 1200 C (1473 K) TIT (Turbine Inlet Gas Temperature) and a rated speed of 100,000 rpm. The authors are now carrying out endurance tests at 1350 C (1623 K) TIT. For ceramic stationary parts, they already finished the evaluations at 1200 ...

UK PubMed Central (United Kingdom)

BackgroundThe successful use of zirconia ceramics in orthopedic surgery led to a demand for dental zirconium-based implant systems. Because of its excellent biomechanical characteristics,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A neutron irradiation test on superplastic ceramic materials at high temperature has been proposed as an innovative basic research on high-temperature engineering using the High Temperature Engineering Test Reactor (HTTR). We investigated mechanical properties, such as the hardness and Young's modulus, of ceramic specimens after superplastic deformation. The tested material was 3Y-TZP (3mol% Yttria stabilized Tetragonal Zirconia Polycrystal) which is one of the representative superplastic ceramics. The properties were measured by a microindentation method. We also studied the relationship between crystal microstructures and the mechanical properties of deformed 3Y-TZP by scanning electron microscope (SEM). The indentation test showed that the mechanical properties of the specimens were reduced to about 1/2 by 30% deformation and to about 1/4 by 150% deformation. The SEM images showed that average grain size and ...

Energy Technology Data Exchange (ETDEWEB)

Externally Fired Combined Cycles (EFCCs) can increase the amount of electricity produced from ash bearing fuels up to 40%, with overall powerplant efficiencies in excess of 45%. Achieving such high efficiencies requires high temperature-high pressure air heaters capable of driving modern gas turbines from gas streams containing the products of coal combustion. A pilot plant has been constructed in Kennebunk, Maine to provide proof of concept and evaluation of system components. Tests using pulverized Western Pennsylvania bituminous coal have been carried out since April, 1995. The ceramic air heater extracts energy from the products of coal combustion to power a gas turbine. This air heater has operated at gas inlet temperatures over 1,095 C and pressures over 7.0 atm without damage to the ceramic tube string components. Stable gas turbine operation has been achieved with energy input from the air heater and a supplementary gas fired combustor. ...

Energy Technology Data Exchange (ETDEWEB)

This work has been undertaken with a view to study the effect of lanthanum content on properties of PLZT ceramics. The polycrystalline complex compounds of PLZT with Pb{sub 1-x}La{sub x}(Zr{sub 0.40}Ti{sub 0.60}){sub 1-x/4}O{sub 3}, +10% PbO formula were prepared from the nano-size individual oxides powders by hot-pressed process. Transparent PLZT (x/40/60) bulk ceramics with pure tetragonal phase was obtained. The studies of the microstructures, dielectric and ferroelectric properties of the ceramics were carried out. The experiment results showed that when La content increased from 7 to 13 mol.%, the grain size increased from 2 to 7 {mu}m. La content also effects the dielectric property obviously, the dielectric constant increased with La content increasing. Moreover, the ferroelectric properties are sensitive to the variation of La content.

Energy Technology Data Exchange (ETDEWEB)

A room-temperature process for stabilizing mineral waste streams has been developed, based on acid-base reaction between MgO and H3PO4 or acid phosphate solution. The resulting waste form sets into a hard ceramic in a few hours. In this way, various alumina industry wastes, such as red mud and treated potliner waste, can be solidified into ceramics which can be used as structural materials in waste management and construction industry. Red mud ceramics made by this process were low-porosity materials ({approx}2 vol%) with a compression strength equal to portland cement concrete (4944 psi). Bonding mechanism appears to be result of reactions of boehmite, goethite, and bayerite with the acid solution, and also encapsulation of red mud particles in Mg phosphate matrix. Possible applications include liners for ponds and thickned tailings disposal, dikes for waste ponds, and grouts. Compatability problems arising at the ...

Energy Technology Data Exchange (ETDEWEB)

The influences of compressive stress on the dielectric properties of (1 - x)Pb(In{sub 1/2}Nb{sub 1/2})O{sub 3}-xPbTiO{sub 3} (x = 0.1-0.5) ceramics was investigated in this study. The dielectric properties were measured under compressive stress applied parallel and perpendicular to electric field. The results clearly showed that the superimposed compression stress had pronounced effects on the dielectric properties of PIN-PT ceramics. In general, with increasing compressive stress the dielectric constant of the ceramics increased and decreased when the stress was applied parallel and perpendicular, respectively, to the electric field direction. The dielectric loss tangent, however, decreased in both stress cases. The observations were mainly interpreted in terms of competing influences of the domain switching through non-180 deg. domain walls, clamping of domain walls, de-ageing and the stress-induced decrease in the ...

Energy Technology Data Exchange (ETDEWEB)

This document contains a listing of the written scientific information originating in the Materials Joining (formerly the Welding and Brazing Group), Metals and Ceramics Division, Oak Ridge National Laboratory during 1951 through June 1991. This registry of documents is as much as possible, in the order of issue date.

International Nuclear Information System (INIS)

Multi-cation #alpha#-Sialon ceramics were prepared using mixtures of samarium with calcium, magnesium, yttrium and ytterbium, and compared with a pure Sm-Sialon of equivalent total stabilising cation composition. A ratio of 80eq% samarium to 20eq% of the second stabilising additive was used. Samples were fired at 1820 deg C and subsequently heat treated at 1450 deg C. XRD phase analysis showed that all additives resulted in greater #alpha#-Sialon stability, and that calcium was the most effective additive for the stabilisation of the #alpha#-Sialon phase. Copyright (1998) Australasian Ceramic Society

Science.gov (United States)

Several commercially available capacitors were evaluated at the liquid nitrogen temperature (77 K). Our primary interest was their performance under a bias voltage when used as DC link capacitors in cryogenic power electronics. In general, the performance of polymer capacitors and certain ceramic capacitors is almost independent of the temperature, DC bias, and frequency. On the other hand, ceramic capacitors based on high dielectric constant materials showed a strong dependence on the boundary conditions. Aluminum electrolytic capacitors showed a dramatic decrease of capacitance at 77 K, possibly due to the electrolyte being frozen and therefore losing its conductivity.

British Library Electronic Table of Contents (United Kingdom)

Purpose - This paper aims to describe the technology and applications of nanocomposite materials. Design/methodology/approach - This paper discusses products, applications and technological developments in polymer, ceramic and metal nanocomposites. It concludes with a brief consideration of electronic component applications. Findings - It is shown that polymer nanocomposites and the materials used in their production are commercially available and finding applications in several industries, including automotive, military, food, electronics and leisure, due to their enhanced mechanical, electrical and thermal properties. Ceramic and metallic nanocomposites are at an earlier stage of development and a critical issue to resolve is optimising the dispersion of nanomaterials in the matrices. Pa...

International Nuclear Information System (INIS)

(Pb_1_-_x La_x) (Zr_0_._6_5 Ti_0_._3_5) ceramics, with x = 0.09 (PLZT 9/65/35) were prepared using lead monoxide (Pb O) with different amount of litharge (tetragonal) and massicot (orthorhombic) phases. Results, based on x-ray diffraction patterns, remanent polarization and dielectric measurements, show that the Pb O polymorphic phase does not change the final structure of the PLZT but causes changes on the remanent polarization and dielectric permittivity temperature dependence. (author). 11 refs, 2 figs, 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

The objective of this contract is to research, develop and demonstrate a novel ceramic membrane reactor system for the low-cost conversion of natural gas to synthesis gas and hydrogen for liquid transportation fuels: the ITM Syngas process. Through an eight-year, three-phase program, the technology will be developed and scaled up to obtain the technical, engineering, operating and economic data necessary for the final step to full commercialization of the Gas-to-Liquids (GTL) conversion technology. This report is a summary of activities through September 1999.

Energy Technology Data Exchange (ETDEWEB)

The collaboration between the Los Alamos National Laboratory and the National Bureau of Standards (NBS), started in 1979, has led to the development of an advanced c-w microtron accelerator design. The four 2380-MHz NBS accelerating structures, containing a total of 184 accelerating cavities, have been fabricated and delivered. New fabrication methods, coupled with refinements of hydrogen-furnace brazing techniques described in this paper, allow efficient production of side-coupled structures. Success with the NBS RTM led to Los Alamos efforts on similar 2450-MHz accelerators for the microtron accelerator operated by the Nuclear Physics Department of the University of Illinois. Two accelerators (each with 17 cavities) have been fabricated; in 1986, a 45-cavity accelerator is being fabricated by private industry with some assistance from Los Alamos. Further private industry experience and refinement of ...

Energy Technology Data Exchange (ETDEWEB)

The Externally-Fired Combined Cycle (EFCC) offers a method for operating high-efficiency gas and steam turbine combined cycles on coal. In the EFCC, an air heater replaces the gas turbine combustor so that the turbine can be indirectly fired. Ceramic materials are required for the heat exchange surfaces to accommodate the operating temperatures of modern gas turbines. The ceramic air heater or heat exchanger is the focus of this program, and the two primary objectives are (1) to demonstrate that a ceramic air heater can be reliably pressurized to a level of 225 psia (1.5 MPa); and (2) to show that the air heater can withstand exposure to the products of coal combustion at elevated temperatures. By replacing the gas turbine combustor with a ceramic air heater, the cycle can use coal or other ash-bearing fuels. Numerous programs have attempted to fuel high efficiency gas turbines directly with coal, often ...

International Nuclear Information System (INIS)

Engineering ceramics have excellent properties such as high strength, high hardness and high heat resistance compared with metallic materials. To apply the ceramic in fast reactor environment, it is necessary to evaluate the sodium compatibility and the influence of sodium on the mechanical properties of ceramics. In this study, the influence of high temperature sodium on the mechanical properties of sintered ceramics of conventional and high purity Al_2O_3, SiC, SiAlON, AlN and unidirectional solidified ceramics of Al_2O_3/YAG eutectic composite were investigated by means of flexure tests. Test specimens were exposed in liquid sodium at 823K and 923K for 3.6Ms. There were no changes in the flexural strength of the conventional and high purity Al_2O_3, AlN and Al_2O_3/YAG eutectic composite after the sodium exposure at 823K. On the contrary, the decrease in the flexural strength was ...

Energy Technology Data Exchange (ETDEWEB)

Processing techniques utilizing low temperature depositions and pulsed lasers allow the fabrication of polysilicon thin film transistors (TFT`s) on plastic substrates. By limiting the silicon, SiO2, and aluminum deposition temperatures to 100(degrees)C, and by using pulsed laser crystallization and doping of the silicon, we have demonstrated functioning polysilicon TFT`s fabricated on polyester substrates with channel mobilities of up to 7.5 cm2/V-sec and Ion/Ioff current ratios of up to 1x10(to the 6th power).

Energy Technology Data Exchange (ETDEWEB)

Since January, 1981, the project of development of nuclear fuel fabrication technology for Wolsung reactor (CANDU type) was undertaken by KAERI(Korea Advanced Energy Research Institute) and successfully fulfilled with loading 24 fuel bundles made by KAERI in Wolsung reactor in September, 1984. On the basis of this accumulated technology and experience, mass production plan to supply all the nuclear fuels for Wolsung reactor is under way. In this presentation, the Korean experience in the development of the nuclear fuel fabrication technology, safety and performance evaluation of KAERI fuel and the results of irradiation of KAERI fuels in Wolsung reactor will be described.

International Nuclear Information System (INIS)

Within the framework of the EU power plant conceptual study (PPCS), a modular He-cooled divertor concept with integrated pin array (HEMP) is being developed at the Forschungszentrum Karlsruhe. The design goal is to achieve a high heat flux of at least about 10-15 MW/m"2, which is proposed for a near-term reactor model like DEMO. The development and optimization of the divertor concept require a close link between the main issues: design, analyses, materials and fabrication technology, and experiments with feedbacks between them to be accounted for. Design-specific requirements on materials and fabrication issues will be discussed.

CERN Document Server

A cost effectively method to fabricate nanopores in silicon by only using the conventional wet-etching technique is developed in this research. The main concept of the proposed method is a two-step etching process, including a premier double-sided wet etching and a succeeding track-etching. A special fixture is designed to hold the pre-etched silicon wafer inside it such that the track-etching can be effectively carried out. An electrochemical system is employed to detect and record the ion diffusion current once the pre-etched cavities are etched into a through nanopore. Experimental results indicate that the proposed method can cost effectively fabricate nanopores in silicon.

Energy Technology Data Exchange (ETDEWEB)

This report presents a brief description of the fabrication and advantages of a composite, carbon-metal fiber material which does not require lubrication.

Science.gov (United States)

Low-cost fabrication of PMC composite sandwich panels, including metallic surface preparations for bonding the PMC to titanium honeycomb. ...

Science.gov (United States)

... to changes in some of the system parameters by means of figures which show the two standard isotherme and two slightly distorted isotherms. ...

Science.gov (United States)

... ge aircraft engines (geae) has taken to development an induction plasma deposition (ipd) processing method for the fabrication of ti6242/sic mmc ...

UK PubMed Central (United Kingdom)

Here we describe the fabrication, optimization, and application of a microfluidic device that integrates microdialysis (MD) sampling, microchip electrophoresis (ME), and electrochemical detection...Full Text Available

Science.gov (United States)

hlgh fiber content composites met the minlmum requirements. (1400 O F ) , the hlgher fiber content as-fabricated composites have impact strengths distinctly ...

Science.gov (United States)

... design, and manufacturing knowledge have been acquired and used to develop an 'in-house' capability for the fabrication of magnetic forming coils ...

International Nuclear Information System (INIS)

The total amount of uranium dissolved in seawater at a uniform concentration of 3 mg U/m3 in the world's oceans is 4.5 billion tons. An adsorption method using polymeric adsorbents capable of specifically recovering uranium from seawater is reported to be economically feasible. A uranium-specific nonwoven fabric was used as the adsorbent packed in an adsorption cage 16 m2 in cross-sectional area and 16 cm in height. We submerged three adsorption cages in the Pacific Ocean at a depth of 20 m at 7 km offshore of Japan. The three adsorption cages consisted of stacks of 52 000 sheets of the uranium-specific non-woven fabric with a total mass of 350 kg. The total amount of uranium recovered by the nonwoven fabric was >1 kg in terms of yellow cake during a total submersion time of 240 days in the ocean.

UK PubMed Central (United Kingdom)

SummaryA microreactor for electrochemical synthesis has been designed and fabricated. It has been shown that different reactions can be carried out successfully using simple protocols.

International Nuclear Information System (INIS)

The feasibility of using a thermoplastic-powder metallurgy technique for the fabrication of porous niobium rods was investigated. Some early problems were overcome to successfully extrude the polymer coated niobium powder into long lengths. The effects of certain process variables were investigated. Residual porosity and extrusion pressure were found to be regulated by the polymer fraction. The procedures for taking the extruded polystyrene--niobium rods through the heat treatments to the final, tin infiltrated stage are explained.

Energy Technology Data Exchange (ETDEWEB)

A prototype of a muffin-tin accelerating structure operating at 32 times the SLAC frequency (2.856 GHz) was built for research in high gradient acceleration. A traveling-wave design with single input and output feeds was chosen for the prototype which was fabricated by wire electrodischarge machining. Features of the mechanical design for the prototype are described. Design improvements are presented including considerations of cooling and vacuum.

Energy Technology Data Exchange (ETDEWEB)

In nuclear fuel, in approximately one quarter of the fissions, one of the two formed fission products is gaseous. These are mainly the noble gases xenon and krypton with isotopes of xenon contributing up to 90% of the product gases. These noble fission gases do not combine with other species, and have a low solubility in the normally used uranium oxide matrix. They can be dissolved in the fuel matrix or precipitate in nanometer-sized bubbles within the fuel grain, in micrometer-sized bubbles at the grain boundaries, and a fraction also precipitates in fuel pores, coming from fuel fabrication. A fraction of the gas can also be released into the plenum of the fuel rod. With increasing fission, and therefore burn-up, the ceramic fuel material experiences a transformation of its structure in the 'cooler' rim region of the fuel. A subdivision occurs of the original fuel grains of few microns size into thousands of small grains of ...

Energy Technology Data Exchange (ETDEWEB)

The cooperative project was a joint development program between Ceradyne and Oak Ridge National Laboratory through Lockheed Martin Energy Research (LMER). Cooperative work was of benefit to both parties. ORNL was able to assess the effect of the microwave nitridation process coupled with gas-pressure sintering for fabrication of parts for advanced diesel engines. Ceradyne gained access to gelcasting expertise and microwave facilities and experience for the nitridation of SRBSN materials. The broad objective of the CRADA between Ceradyne and OIWL was to (1) examine the applicability of the gelcasting technology to fabricate parts from SRBSN, and (2) to assess the effect of the microwave nitridation of silicon process coupled with gas-pressure sintering for fabrication of parts for advanced diesel engines. The following conclusions can be made from the work performed under the CRADA: (1) Gelcasting is a viable method to ...

International Nuclear Information System (INIS)

Immobilization of long-lived fission products (LLFP) such as radioactive Tc, Cs and Sr into #alpha#-SiAlON ceramics was evaluated using stable isotopes instead of radioactive isotopes, and the applicability of #alpha#-SiAlON ceramics as the inert matrix for transmutation of LLFP was investigated. In the case of single addition of SrO, SrCO_3, Cs_2CO_3 or ReO_2 to the starting materials, #alpha#-SiAlON, single phase was not formed after hot-pressing. When Y_2O_3 was added with SrO, SrCO_3 or Cs_2CO_3 to the starting materials (#alpha#-Si_3N_4, AlN and #alpha#-Al_2O_3) in optimum compositions, #alpha#-SiAlON single phase was obtained after hot-pressing at 1700degC or 1800degC. From the EDS analysis, Sr and Y were detected from grains. It is suggested that Y would assist the expansion of interstices of #alpha#-SiAlON lattice, resulting in the incorporation of Sr"2"+ into #alpha#-SiAlON lattice. In the case of Cs addition with Y, Cs was not ...

Energy Technology Data Exchange (ETDEWEB)

A radioactive Waste Incineration System (WIS) with suspension combustion is noticed as effective volume reduction technology of low level radiactive wastes that are increasing every year. In order to demonstrate the decontamination efficiency of ceramic filter used on WIS, this test has been carried out with the test facilities as joint research of Central Research Institute of Electric Power Industry (CRIEPI) and Sumitomo Heavy Industries, Ltd. Miscellaneous combustible waste and power resin, to which 5 nuclides (Mn-54, Fe-59, Co-60, Zn-65, Cs-137) were added, were used as samples for incineration. As the result of the test, it was verified that Decontamination Factor (DF) of the single stage ceramic filter was usually kept over 10/sup 5/ for every nuclide, and from the results of above DF, over 10/sup 8/ is expected for real commercial plant as a total system. Therefore, it is realized that the off-gas clean up system of the WIS composed of ...

International Nuclear Information System (INIS)

In this letter a method to estimate the visco-elastic response of monolithic ceramics to cyclic loading conditions at high temperatures is proposed. A relation is observed between the visco-elastic energy dissipation measured for two silicon nitride materials, and the structural characteristics of their respective intergranular phases. Some consequences for the fatigue resistance of the tested materials, and of non-transforming monolithic ceramics in general, are discussed. Two batches (G for glassy and C for crystalline) of SiAlON have been studied. The G-batch is obtained by pressureless sintering of silicon nitride powder with Y_2O_3 (6 wt%) and 6AlN-SiO_2 (5 wt%) as sintering additives. The main phase after sintering is #beta#-sialon. Upon cooling from the sintering temperature the amorphous intergranular residues of the sintering additives and of SiO_2, which is unavoidably present as a thin layer on the silicon nitride powder, crystallize ...

International Nuclear Information System (INIS)

The design of solid breeder blankets is strongly affected by the low values of thermal conductivity and density of ceramic breeder pebble beds. A significant rise of both quantities would enhance the thermal performance and lead to an increased tritium breeding ratio. In order to improve these quantities pretreated lithium orthosilicate pebble material was dry pressed and subsequently sintered. The thermal conductivity of cylindrical pellets was determined by the heat pulse method using a laser flash device. A pebble bed characteristic sample was also investigated in order to check the measurement accuracy in comparison with previous results. Furthermore, two samples of low density cellular ceramics were also prepared by infiltration of polymer foams with a ceramic slurry. The thermal conductivity results show that the values are affected both by the particle size and the sample density. Thermal conductivity values of ...

Energy Technology Data Exchange (ETDEWEB)

Fine ceramic particles of zirconia toughened alumina (ZTA), titania toughened alumina (TTA), and zirconia-titania toughened alumina (ZTTA) have been synthesized by ultrasonic spray pyrolysis (USP) at various temperatures from starting salt solutions of various compositions aiming for the development of catalytic material. These particles were characterized for properties such as shape, size and size distribution, diffraction pattern, and chemical and phase composition of elements by scanning electron microscopy (SEM), particle size analyzer (PSA), x-ray diffraction (XRD), and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Chemical compositions and sizes of ceramic composites have been controlled by the stoichiometry of salt solutions and the flow rate of spraying solutions. The optimum experimental conditions for the various composite particle synthesis have been proposed.

Energy Technology Data Exchange (ETDEWEB)

The meeting was arranged into the following sessions: introductory; advanced ceramics and ceramic composites; ceramic and metal matrix composites; electronic materials and devices; acoustoelasticity, stress, and texture; composites-porosity, strength, and UT propagation; process modeling and monitoring; thermal wave physics; material properties, composites, surfaces, and interfaces; acoustic emission; ferromagnetic materials; new sensors; NDE reliability assessment; elastic wave scattering and propagation; image analysis, data storage, and signal processing; UT transducers; weldments and bonded materials; eddy current models; unified life cycle engineering; x rays, CT, and NMR; eddy current probes and instruments; acoustic microscopy imaging, and reconstruction; signal processing, measurement techniques, and systems; NDE applications of artificial intelligence; crack behavior influenced by history; inversion procedures for ...

Energy Technology Data Exchange (ETDEWEB)

Ceramics with composition Ba{sub 1-x}Na{sub x}Ti{sub 1-x}Nb{sub x}O{sub 3} are of either classical ferroelectric (for 0{<=}x<0.075) and ferro- or antiferroelectric (for 0.55<x{<=}1) or relaxor ferroelectric type (for 0.075{<=}x{<=}0.55), the transition at T{sub c} being only diffuse without any frequency dispersion for this last region. All the corresponding dielectric characteristics, i.e. diffusivity of the ferroelectric-paraelectric transition, frequency dispersion of {epsilon}{sub r}', shift of T{sub m} with frequency deviation from the Curie-Weiss law, are determined. The relaxor behaviour is more relaxor the more the composition deviates from BaTiO{sub 3} and NaNbO{sub 3}. This study is in the field of preparation of relaxor ceramics free from lead in the interest of the environment, which present a transition temperature close to room temperature. (author)

Energy Technology Data Exchange (ETDEWEB)

Aiming to realize ball bearings operable in a vacuum and under high temperature, silicon nitride (Si3N4) ceramic ball bearings were tested. The tested ball bearings were angular contact ball bearings composed of silicon nitride with sputtered molybdenum disulfide coating using a retainer of hot-pressed self-lubricating composite material. The time variation of the frictional torque was examined for the operations under the conditions at 500{degree}C in a vacuum at a rotational speed of 600 rpm and 50N thrust load for 5{times}10{sup 7}revolutions (1400 hours) and for 1.5{times}10{sup 8}revolutions (4200 hours). Excellent tribological performance was obtained. The ball bearings are lubricated with the molybdenum disulfide film at the initial stage of the operation and with a transfer film formed from the retainer material to the balls. In a test at 650{degree}C, low and stable frictional torque was observed up to 500 hours of operation as of the 500{degree}C test, no ...

International Nuclear Information System (INIS)

Carbide ceramics such as boron carbide due to their unique properties such as low density, high refractoriness, and high strength to weight ratio have many applications in different industries. This study focuses on direct bonding of boron carbide for high temperature applications using nickel interlayer. The process variables such as bonding time, temperature, and pressure have been investigated. The microstructure of the joint area was studied using electron scanning microscope technique. At all the bonding temperatures ranging from 1150 to 1300degC a reaction layer formed across the ceramic/metal interface. The thickness of the reaction layer increased by increasing temperature. The strength of the bonded samples was measured using shear testing method. The highest strength value obtained was about 100 MPa and belonged to the samples bonded at 1250 for 75 min bonding time. The strength of the joints decreased by increasing the bonding ...

International Nuclear Information System (INIS)

A family of sealant materials has been developed for use in the solid oxide fuel cell (SOFC) and in other applications in the temperature range of 800 endash 1000 degree C. These materials are based on glasses and glass-ceramics in the SrO endash La_2O_3 endash Al_2O_3 endash B_2O_3 endash SiO_2 system. The coefficients of thermal expansion (CTE) for these materials are in the range of 8 endash 13x10"-"6/degree C, a good match with those of the SOFC components. These sealant materials bond well with the ceramics of the SOFC and, more importantly, form bonds that can be thermally cycled without failure. At the fuel cell operating temperature, the sealants have viscosities in the range of 10"4-10"6 Pa-s, which allow them to tolerate a CTE mismatch of about 20% among the bonded substrates. The gas tightness of a sample seal was demonstrated in a simple zirconia-based oxygen concentration cell. copyright 1996 Materials Research Society.

Energy Technology Data Exchange (ETDEWEB)

The effects of Fe and B{sub 4}C on the sintering behavior and mechanical properties of TiB{sub 2} ceramics have been studied. Sintering was performed in an Ar atmosphere at 2000{degrees}C using attrition-milled TiB{sub 2} powder. When a small amount of Fe (0.5 wt%) was added, abnormal grain growth occurred and the sintered density was low. In the case of B{sub 4}C added along with 0.5 wt% Fe, however, abnormal grain growth was remarkably suppressed, and the sintered density was increased up to 95% of theoretical. But with excess Fe addition (5 wt%), B{sub 4}C grains did not act as a grain growth inhibitor, and B{sub 4}C grains were frequently trapped in large TiB{sub 2} grains. The best mechanical properties were obtained for the TiB{sub 2}-10 wt% B{sub 4}C-0.5 wt% Fe ceramics, which exhibited a three-point bending strength of 400 MPa and a fracture toughness of 5.5 MPa {center dot} m{sup 1/2}.

Energy Technology Data Exchange (ETDEWEB)

MOX fuel for FBR is allowed to contain impurities within several thousand ppm, which means less than 1000 of decontamination factor (DF) in reprocessing is enough for Pu and U recycle use. The Advanced Fuel Recycle proposed by PNC is on this basis. The concept consists of innovations on both MOX fuel fabrication and aqueous reprocessing technologies based on the Purex process and it is believed that successful optimization of fuel cycle interface condition is the key issue to realize the concept. The lower DF such as 1000 can be easily obtained by the simplified Purex flowsheet which has no purification steps. However, new subject arises in MOX fuel fabrication, that is, fabrication is conducted in the shielding cell using equipment which is maintained remotely. A simplified fabrication technology becomes essential to establish the remote maintenance system and is one of the critical path for achieving ...

British Library Electronic Table of Contents (United Kingdom)

Statement of problem The use of titanium has increased for metal ceramic restorations, as well as for use in titanium implants, with developments in CAD/CAM technology. Some surface treatments of titanium have been introduced to enhance the titanium bond strength to low-fusing porcelains; however, a more reliable, easily used dental laboratory method has not been established. Purpose The purpose of this study was to compare the effect of laser etching as a titanium surface treatment with 3 other surface treatments (machining, airborne-particle abrasion, and acid etching), evaluating their ability to enhance the bond strength between a titanium substrate and porcelain. Material and methods A total of 64 specimen rods of commercially pure titanium (ASTM grade 2, 20 mm in length and 5.7 mm in...

International Nuclear Information System (INIS)

Ceramic fuel element is one of the most important items of HTGR technology, and the corrosion resistance of is matrix materials is vital to the operational performance of HTGR. In the paper, based on the oxidation study of the matrix materials, it has been proposed that the corrosion resistance of the matrix materials might be improved through forming carbon -ceramic composite. The experiment results have shown that the corrosion resistance of matrix materials has been improved by addition of SiC superfine powders, and that the matrix materials containing SiC superfine powders and heat-treated at 1600 deg. C had an oxidation rate lower than the general one containing no SiC superfine powder and heat-treated at 1950 deg. C. (author). 5 refs, 8 figs.

British Library Electronic Table of Contents (United Kingdom)

Porous ?-SiAlON ceramics are synthesized by reaction bonded method using hollow alumina spheres (HASs) as both sintering aids and pore-forming agents. Both micropores and macropores, which are constructured by SiAlON grains with different morphologies, are formed in the final SiAlON samples. The micropores are three-dimentional, and are built by equiaxial grains. While the hollow macropores, which have the similar morphology to hollow alumina sphere, are packed by elongated grains. In the sintering process, the solid dissolution process takes place, giving rise to the different alumina concentration of liquid phase, and thus resulting in the formation of two kinds of grains, the equiaxial grain and the elongated grain.

International Nuclear Information System (INIS)

#beta#-sialon ceramics of equal overall compositions but containing amorphous, partly crystalline and almost completely crystalline intergranular phase(s) have been oxidized in oxygen at 1350 deg C for 20 hours. The obtained weight gain curves do not follow the parabolic rate law (#DELTA#W/A_0)"2= k_pt + #beta#. To the extent that crystallization occurs in the oxide scale during the oxidation experiment, the amorphous cross section area through which oxygen most easily diffuses will decrease with time. A brief description of this new rate law is given, and the obtained oxidation curves will be discussed within that framework. 4 refs., 2 tabs., 2 figs.

Energy Technology Data Exchange (ETDEWEB)

Advances in nuclear reactor technology and the use of gas-cooled fast reactors require the development of new materials that can operate at the higher temperatures expected in these systems. These include refractory alloys base on Nb, Zr, Ta, Mo, W, and Re; ceramics and composites such as those based on silicon carbide (SiCf-SiC); carbon-carbon composites; and advanced coatings. Besides the ability to handle higher expected temperatures, effective heat transfer between reactor componets is necessary for improved efficiency. Improving thermal conductivity of the materials used in nuclear fuels and other temperature critical components can lower the center-line fuel temperature and thereby enhance durability and reduce the risk of premature failure.

British Library Electronic Table of Contents (United Kingdom)

Statement of problem Because noble dental casting alloys for metal ceramic restorations have a wide range of mechanical properties, knowledge of these properties is needed for rational alloy selection in different clinical situations where cast metal restorations are indicated. Purpose The purpose of this study was to compare the mechanical properties and examine both the fracture and polished surfaces of 6 noble casting alloys that span many currently marketed systems. Five alloys were designed for metal ceramic restorations, and a sixth Type GPT has Type IV alloy for fixed prosthodontics (Maxigold KF) was included for comparison. Material and methods Specimens (n=6) meeting dimensional requirements for ISO Standards 9693 and 8891 were loaded to failure in tension using a universal testin...

British Library Electronic Table of Contents (United Kingdom)

Statement of problem Titanium is the most biocompatible metal used for dental casting; however, there is concern about its marginal accuracy after porcelain application since this aspect has direct influence on marginal fit. Purpose The purpose of this study was to determine the effect that metal selection and the porcelain firing procedure have on the marginal accuracy of metal ceramic prostheses. Material and methods Cast CP Ti, milled CP Ti, cast Ti-6Al-7Nb, and cast Ni-Cr copings (n=5) were fired with compatible porcelains (Triceram for titanium-based metals and VITA VMK 95 for Ni-Cr alloy). The Ni-Cr alloy fired with its porcelain served as the control. Photographs of metal copings placed on a master die were made. Marginal discrepancy was determined on the photographs using an image ...

International Nuclear Information System (INIS)

The energy levels scheme of octahedrally coordinated Ni2+ ion in single crystal, powder nano-single crystal, ceramics and glass-ceramics of MgGa2O4 host matrix, has been calculated in the exchange charge model of crystal field. The parameters of the crystal field acting on the Ni2+ ion are calculated from the crystal structure data, after optimization of the geometry of the system. The energy level schemes have been calculated by diagonalization of the crystal field Hamiltonian of this system. The obtained results were compared with experimental data; a good agreement were demonstrated, which confirm the validity of the model and used method.

International Nuclear Information System (INIS)

The purpose of the present study is to develop a new method for chemical state analysis by means of EPMA(Electron probe microanalyser). The measured X-ray intensity of Si-K#beta# characteristic X-ray spectra were read-out by a 16 bit microcomputer with a RS-232C interface. And using the curve fitting method the quantitative analysis of chemical compositions in a ternary compound that constituted of the same element has been established. The present method was applied to analyse of the friction and wear properties of Si-base ceramics sliding materials. It was found that the wear debris contains both the compositions of the sliding materials and SiO_2, and the SiO_2 contents in wear debris was changed with relative humidity. The results clearly showed that the proposed method is very useful for determing the compositions in the ternary compound. (author).

Science.gov (United States)

Course website from Cambridge on ceramic materials. This site contains eight lectures in PDF format (Adobe Reader required), two question sheets, five practicals (including answers), digital movies and further useful links. "There is a strong relationship between the structure of a material and its physical properties. The properties of a material whether mechanical, electrical, optical or magnetic, determine how it can be used in practical applications. In this course, the focus is on the structure / property relationship for ionic materials with electrical properties utilised in various transducer devices. The materials considered include perovskites, which have special polarisation properties exploited in ferroelectric, pyroelectric and piezoelectric devices. Other oxides, such as zirconia, have structures permitting rapid diffusion of ions, making them suitable for use in sensors, fuel cells and batteries. The scientific principles underlying the properties of ...

International Nuclear Information System (INIS)

Dy doped #alpha#-SiAlON ceramics prepared by the hot-pressing method show a high optical transmittance value, >70%, in the infrared region of 1.5-4.5 #mu#m. First principles calculations have been carried out to reveal the underlying transparency mechanism. It is found that the valence shell of doped Dy atoms interacts strongly with the doping states of #alpha#-SiAlON, resulting in the increase in the optical gap from 0.4 to 1.1 eV, which suppresses the photoabsorption in the wavelength region longer than 1.0 #mu#m and leads to the good transparency property. The calculated optical transmission spectra are in good agreement with the corresponding experiments.

British Library Electronic Table of Contents (United Kingdom)

We report the fabrication and characterization of glucose-tolerant Raney-platinum cathodes for oxygen reduction in potentially implantable glucose fuel. Fabricated by extraction of aluminum from 1mm thin platinum-aluminum bi-layers annealed at 300^oC, the novel cathodes show excellent resistance against hydrolytic and oxidative attack. This renders them superior over previous cathodes fabricated from hydrogel-bound catalyst particles. Annealing times of 60, 120, and 240min result in approximately 400-550nm thin porous films (roughness factors ~100-150), which contain platinum and aluminum in a ratio of ~9:1. Aluminum release during electrode operation can be expected to have no significant effect on physiological normal levels, which promises good biocompatibility. Annealing time has a dis...

Energy Technology Data Exchange (ETDEWEB)

In an effort to develop a simple low-temperature high-performance polysilicon thin-film transistor (TFT) technology, the authors report a fabrication process featuring laser-crystallized sputtered-silicon films. This top Al-gate coplanar TFT process subjects the substrate to a maximum temperature of 300 C, and produces devices with mobilities up to 450 cm{sup 2}/Vs, on/off current ratios greater than 10{sup 7}, without using a post-hydrogenation step. They believe these results represent the highest performance TFT`s to date fabricated from sputtered silicon films.

British Library Electronic Table of Contents (United Kingdom)

Abstract A highly efficient enzyme immobilization method has been developed for electrochemical biosensors using polydopamine films with gold nanoparticles (AuNPs) embedded. This simple enzyme fabrication method can be performed in very mild conditions and stored in a long time with high bioactivity. The fabricated amperometric glucose biosensor exhibited a high and reproducible sensitivity, wide linear dynamic range and low limit of detection (LOD) (0.1 molL-1). A low value of 1.5 mmolL-1 for the apparent Michaelis-Menten constant KappM was obtained. The high sensitivity, wide linear range, good reproducibility and stability make this biosensor a promising candidate for portable amperometric glucose biosensor.

International Nuclear Information System (INIS)

The performance of scanning driver circuits fabricated with self-aligned aluminum gate polysilicon thin-film transistors (TFT's) is demonstrated. After the gate electrode patterning, the fabrication process temperature is kept below 400degC to enable the use of aluminum gate electrodes. The low-temperature crystallization phenomenon, which occurs when protons are implanted simultaneously with boron or phosphorus dopants, is employed to eliminate the 600degC activation-annealing process. A maximum clock frequency of about 2.0 MHz is achieved when the driver operating voltage is 24 V and the TFT channel length is 12 #mu#m. (author).

British Library Electronic Table of Contents (United Kingdom)

Herein, we demonstrate the structure of the PS colloidal crystals which were fabricated on the hydrophilic/hydrophobic Si wafers by a spin-coating technique. Monodisperse PS colloids are spin-coated onto self-assembled monolayers of 3-(aminopropyl)triethoxysilane and propyltrimethoxysilane coated Si wafers. PS spheres organized as ordered close-packed face-centered cubic structure with (111) planes on the hydrophilic surface while they gathered without the crystal structure on the hydrophobic surface. This paper also reports a simple and rapid method to fabricate the close-packed structure of hollow TiO2 spheres. The colloidal crystal of TiO2 hollow spheres was prepared using the PS sphere template on the hydrophobic surface. The mechanism for the growing multilayers of self-assembled PS p...

British Library Electronic Table of Contents (United Kingdom)

To improve the friction and wear behavior of carbon fabric reinforced polymer composites (CFRP), nano-SiO2 was deposited on the fabric surface. The friction and wear behavior of the resulting composites were investigated on a model ring-on-block test rig. Experimental results revealed that fiber surface treatment contributed to largely improve the tribological properties of the CFRP composites. Scanning electron microscope (SEM) investigation showed that the worn surface of the surface modified CFRP composite was smoother under given load and sliding rate. Field emission scanning electron microscopy (FESEM), FTIR and X-ray photoelectron spectroscopy (XPS) studies of the carbon fiber surface showed that nanostructured Sio2 thin film can be obtained by SiO2 sols deposition, which improved th...

Energy Technology Data Exchange (ETDEWEB)

The scale-down of a liquid mini-pump (order of 10 mm) to a micrometre scale has been attempted using a novel valveless nozzle-diffuser design and new application of an organic physical vapor-deposited membrane. The micropump employs no moving parts other than the membrane and accomplishes the rectification of fluid flow due to pressure recovery differences in the nozzle and diffuser flow directions. More specifically, liquids flow with less resistance (i.e. conduct more fluid) in the diffuser direction than the nozzle direction, for a given pressure differential. At the micrometre scale, the fabrication of the critical nozzle and diffuser elements was performed by focused ion beam (FIB) microlithography of glass slides. Etched slides were sandwiched to make two-dimensional venturis. Sternme and Sternme noted the importance of a lower Reynolds Number linfit on the desired pressure recovery which challenged the fabrication of this pump design at ...

International Nuclear Information System (INIS)

One-dimensional core-shell polymer nanowires offer many advantages and great potential for many different applications. In this paper we introduce a highly versatile two-step template wetting process to fabricate two-component core-shell polymer nanowires with controllable shell thickness. PLLA and PMMA were chosen as model polymers to demonstrate the feasibility of this process. Solution wetting with different concentrations of polymer solutions was used to fabricate the shell layer and melt wetting was used to fill the shell with the core polymer. The shell thickness was analyzed as a function of the polymer solution concentration and viscosity, and the core-shell morphology was observed with TEM. This paper demonstrates the feasibility of fabricating polymer core-shell nanostructures using our two-step template wetting process and opens the arena for optimization and future experiments with polymers that are desirable ...

UK PubMed Central (United Kingdom)

Quartz has a dissipation factor of approximately 10(-4), which is an order of magnitude less than that of the best glasses previously used to fabricate patch pipettes; it's dielectric constant of 3.8...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper addresses one source of degradation in OPV devices: the metal/organic interface. The basic approach was to study the completed device stability vs. the stability of the organic film itself as shown in subsequent devices fabricated from the films.

Energy Technology Data Exchange (ETDEWEB)

We present device results from polysilicon thin film transistors (TFTs) fabricated at a maximum temperature of 100&hthinsp;{degree}C on polyester substrates. Critical to our success has been the development of a processing cluster tool containing chambers dedicated to laser crystallization, dopant deposition, and gate oxidation. Our TFT fabrication process integrates multiple steps in this tool, and uses the laser to crystallize deposited amorphous silicon as well as create heavily doped TFT source/drain regions. By combining laser crystallization and doping, a plasma enhanced chemical vapor deposition SiO{sub 2} layer for the gate dielectric, and postfabrication annealing at 150&hthinsp;{degree}C, we have succeeded in fabricating TFTs with I{sub ON}/I{sub OFF} ratios {gt}5{times}10{sup 5} and electron mobilities {gt}40 cm{sup 2}/V&hthinsp;s on polyester substrates. {copyright} {ital 1999 American Vacuum ...

International Nuclear Information System (INIS)

The installation procedure, the fabrication, fitting up, positioning, adjustment and welding of piping, examinations, hydrostatics testing and insulation of piping for reactor primary circuit piping of Daya Bay Nuclear power Plant are briefly described.

Science.gov (United States)

A feasibility study to determine what materials and geometric systems would be required for fabrication of a camouflage system that would instantaneously cover a military vehicle in order to disrupt its characteristic shape or outline. The program involve...

Science.gov (United States)

Two manufacturing processes have been developed for fabricating PLZT bonded lens assemblies (BLA's) for the USAF EEU-2/P Thermal/Flash Protective Goggle. One process utilizes thin Sylgard spacers which remain in the BLA to establish bond thickness between...

Energy Technology Data Exchange (ETDEWEB)

Solving the maintenance and repair problems of electronic instruments, we have supported the research and development work, and reduced operation costs of the pilot plants in KAERI. In addition, we have imposed the maintainability of instruments to use effectively. 15 tabs., 14 figs., 14 refs. (Author) .new.

Energy Technology Data Exchange (ETDEWEB)

The authors report on the nano-fabrication of GaN/AlGaN device structures using focused ion beam (FIB) etching, illustrated on a GaN/AlGaN heterostructure field effect transistor (HFET). Pillars as small as 20nm to 300nm in diameter were fabricated from the GaN/AlGaN HFET. Micro-photoluminescence and UV micro-Raman maps were recorded from the FIB-etched pattern to assess its material quality. Photoluminescence was detected from 300nm-size GaN/AlGaN HFET pillars, i.e., from the AlGaN as well as the GaN layers in the device structure, despite the induced etch damage. Properties of the GaN and the AlGaN layers in the FIB-etched areas were mapped using UV Micro-Raman spectroscopy. Damage introduced by FIB-etching was assessed. The fabricated nanometer-size GaN/AlGaN structures were found to be of good quality. The results demonstrate the potential of FIB-etching for the nano-fabrication of III-V nitride ...

Energy Technology Data Exchange (ETDEWEB)

;Contents: Energy Use; Building Fabric Performance; Ventilation and Infiltration; Passive Solar Design; Heating Systems and Controls; Hot and Cold Water Provision; and Lighting and Electrical Appliances.

International Nuclear Information System (INIS)

Nanoporous materials have become indispensable in many fields ranging from photonics, catalysis and semiconductor processing to biosensor infrastructure. Rapid and energy efficient process fabrication of these materials is, however, nontrivial. In this communication, we describe a simple method for the rapid fabrication of these materials from colloidal dispersions of Polymethyl Silsesquioxane nanoparticles. Nanoparticle-polymer composites above the decomposition temperature of the polymer are examined and the entropic gain experienced by the nanoparticles in this rubric is harnessed to fabricate novel highly porous films composed of nanoparticles. Optically smooth, hydrophobic films with low refractive indices (as low as 1.048) and high surface areas (as high as 1325 m2 g-1) have been achieved with this approach. In this communication we address the behavior of such systems that are both temperature and substrate surface ...

Energy Technology Data Exchange (ETDEWEB)

The effects of gate and drain bias stresses on thin film transistors fabricated in polysilicon films crystallized using the advanced sequential lateral solidification excimer laser annealing (SLS ELA) process, which yields very elongated polysilicon grains and allows the fabrication of TFTs without grain boundary barriers to current flow, are investigated as a function of the active layer thickness and of the TFT orientation relative to the grains. The application of hot carrier stress, with a condition of V{sub GS} = V{sub DS}/2, was determined to induce threshold voltage, subthreshold swing and transconductance degradation for TFTs in thicker polysilicon films and the associated stress-induced increase in the active layer trap density was evaluated. However, this device degradation was drastically reduced for TFTs fabricated in ultra-thin films. Furthermore, the application of the same stress condition to TFTs oriented ...

Science.gov (United States)

... impact criterion, as demonstrated by the materials research community. These include training ... designing new materials or new processing/fabrication routes to existing materials; exploring and ...

UK PubMed Central (United Kingdom)

An image slicing spectrometer (ISS) for microscopy applications is presented. Its principle is based on the redirecting of image zones by specially organized thin mirrors within a custom fabricated...Full Text Available

International Nuclear Information System (INIS)

Iron oxide as sintering aid to Ce-TZP ceramics produces a beneficial effect on the tetragonal phase stabilization. It was found that ceria powder particle size of 2,0 #mu#m turns the grain-boundary electrical conductivity higher than ceria powder of smaller grain size. (author)

British Library Electronic Table of Contents (United Kingdom)

In this paper, we present the photoluminescence properties of Pr3+-, Sm3+- and Dy3+-doped germanate glasses and glass ceramics. From the X-ray diffraction measurement, the host glass structure was determined. These glasses have shown strong absorption bands in the near-infrared (NIR) region. Compared to Pr3+-, Sm3+- and Dy3+-doped glasses, their respective glass ceramics have shown stronger emissions due to the Ba2TiGe2O8 crystalline phase. For Pr3+-doped glass and glass ceramic, emission bands centered at 530nm (3P03H5), 614nm (3P03H6), 647nm (3P03F2) and 686nm (3P03F3) have been observed with 485nm (3H43P0) excitation wavelength. Of them, 647nm (3P03F2) has shown bright red emission. Emission bands of 4G5/26H5/2 (565nm), 4G5/26H7/2 (602nm) and 4G5/26H9/2 (648nm) for the Sm3+:glass and gl...