Energy Technology Data Exchange (ETDEWEB)

Microwaves were used to induce self-propagating high temperature synthesis (SHS) in the reaction 3TiO{sub 2}+3C+(4+x)Al {yields} 3TiC+2Al{sub 2}O{sub 3}+xAl. The SHS process was studied for x = 0 and 4, using slow and fast heating rates and with and without the application of uniaxial pressure. Less than 50 watts was required to internally ignite the samples using a TE{sub 102} microwave cavity mode. Uniaxial stresses in the range of 200-1400 psi were continuously applied along the vertical axis of some of the processed samples as the SHS reactions were initiated. SEM photomicrographs clearly indicate differences in the formation of whiskers and other microstructural features in the products obtained from microwave and conventional hot wire techniques. The x = 0 samples processed with fast and slow microwave heating rates reached higher densities than the conventionally processed samples.

International Nuclear Information System (INIS)

With the assistance of mechanical activation, yttrium-stabilized #alpha#-SiAlON was prepared by combustion synthesis in air, instead of high-pressure N_2 atmosphere for the first time. The reaction activity of metallic particles was remarkably enhanced by mechanical activation, which conduced the reduction of grain size, increased the total surface area and formation of fresh surface. The formation of #alpha#-SiAlON by combustion synthesis in air was explained by a kinetically induced reaction mechanism, in which both initial formation of #alpha#-SiAlON and following avoidance of oxidation were fulfilled by the retardation of O_2 infiltration owing to the short reaction period and fast cooling rate.

British Library Electronic Table of Contents (United Kingdom)

Total synthesis of cis-solamin A was accomplished without using protecting groups starting from (-)-muricatacin in 11 steps with an overall yield of 4.5%. The backbone of cis-solamin A was constructed by olefin cross-metathesis between the tetrahydrofuran moiety and g-lactone moiety. An enzymatic kinetic transesterification procedure was successfully applied to the synthesis of an optically pure g-lactone moiety.

Energy Technology Data Exchange (ETDEWEB)

This investigation involves a study of the influence of key processing parameters on the heating of materials using microwave energy. Selective and localized heating characteristics of microwaves will be utilized in the sintering of ceramics without hydrostatic pressure. In addition, combustion synthesis will be studied for the production of powders, carbides, and nitrides by combining two or more solids or a solid and a gas to form new materials. The insight gained from the interaction of microwaves with various materials will be utilized in the mobilization and subsequent redeposition of uranium.

UK PubMed Central (United Kingdom)

The high-yield, stereoselective conversion of geraniol (3,7-dimethyl-trans-2,6-octadien-1-ol) to the insect juvenile hormone, methyl 12,14-dihomojuvenate (methyl cis-10-epoxy-3,11-dimethyl-7-ethyl-trans,...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Doped ultrafine silicon dioxide powder with a narrow particle size distribution was obtained by RF discharge-stimulated dichlorosilane (SiH2C) oxidation at a low pressure using isobutylene as the combustion inhibitor and chromium hexacarbonyl (Cr(CO)6) as the dopant. The formation and morphology of the ultrafine particles are governed by the parameters of the RF discharge and by the chemical mechanism of the combustion reaction yielding the aerosol. Submicron-sized filamentous carbon structures can be obtained by isobutylene decomposition under spark discharge conditions in the presence of a molybdenum metal catalyst.

British Library Electronic Table of Contents (United Kingdom)

Only 15mol% of l-proline in ethanol proved to be a very efficient catalyst for the one-pot synthesis of a wide variety of highly substituted pyridines at room temperature. The methodology is mild, efficient, high yielding, and the products can be directly recrystallized from hot ethanol.

Science.gov (United States)

Research programs on coal and coal liquefaction are presented. Topics discussed are: coal science, combustion, kinetics, surface science; advanced technology projects in liquefaction; two stage liquefaction and direct liquefaction; catalysts of liquefaction; Fischer-Tropsch synthesis and thermodynamics; alternative fuels utilization; coal preparation; biodegradation; advanced combustion technology; flue gas cleanup; environmental coordination, and technology transfer. Individual projects are processed separately for the data base. (CBS)

Energy Technology Data Exchange (ETDEWEB)

This report describes the combustion experiments performed using the SP Industry Calorimeter. In addition to measuring parameters such as heat release rate (HRR), mass loss rate, effective heat of combustion and smoke obscuration, considerable effort was put into the characterisation of the smoke gases in order to obtain a basis for evaluations of the toxic potency of the smoke. The materials studied were Nylon 66, polypropene, polystyrene (with and without fire retardant, respectively), PVC and chlorobenzene. A total of 19 large-scale, well ventilated combustions were carried out. The mass of sample burned ranged from 20 kg to 125 kg in an experiment. A procedure was designed for cleaning the smoke gas duct between experiments and was found to be effective. Measurements were carried out for the amounts of O{sub 2}, CO{sub 2}, CO, NO{sub x}, THC (unburned hydrocarbons), HCN, HCl, NH{sub 3} and individual organic compounds ...

International Nuclear Information System (INIS)

Electricity generation from natural gas in gas turbine units can be made substantially more efficient by preliminary methane conversion to a synthesis gas containing hydrogen and carbon monoxide and/or by the use of some of the synthesis gas produced in industry. An alternative improvement involves the introduction of solid oxide fuel cells (SOFCs) and the use of the synthesis gas in them. In this study, a modified scheme of gas turbine cycle that includes an SOFC, a membrane reactor (instead of a traditional combustion chamber), and a catalytic reactor to perform methane conversion to produce hydrogen (synthesis gas) is proposed. Variations of the energy and exergy efficiencies of the integrated system with operating conditions are provided, showing, for example, that SOFC efficiency is enhanced if the fuel cell active area is augmented. The SOFC stack efficiency can be maximized ...

British Library Electronic Table of Contents (United Kingdom)

Unsymmetric diaryl alkynes were synthesized from the palladium-catalyzed decarboxylative coupling of aryl halides and propiolic acid using a continuous flow reaction system. This flow chemistry system continuously gave the desired products in moderate to good yields, and produced less byproduct than was formed in the batch reaction.

International Nuclear Information System (INIS)

Molybdenum oxide nanostructures were synthesized utilizing the solution combustion method where the ammonium molybdate powder and an organic additive were used as precursors. Different organic additives including ethylene diamine tetra-acetic acid (EDTA), polyethylene glycol 200 (PEG 200), sorbitol and urea were used as surfactants in order to investigate the effect of additive structure on morphology and particle size of products. Also various reaction parameters such as the additive/Mo molar ratio, concentration of metal ion in solution, pH of the reaction, and temperature of the synthesis media were changed to study effects on product morphology and size. Outcomes were characterized by Scanning Electron Microscopy (SEM), X-ray diffraction, and Transmission Electron Microscopy (TEM) techniques. Results show a variety of MoO_3 nanoparticles and nanorods produced within the size range of 10-80 nm. Furthermore, microrods and microsheets were ...

Energy Technology Data Exchange (ETDEWEB)

The potential to increase the productivity of fuel straw harvest and transportation was examined. When harvesting straw for energy purposes, only the long fraction is currently collected. However, technological improvements have now rendered it possible to harvest chaff, thus increasing the amount of harvest residues and bale density. The purpose of this study was to determine how harvest yield, bale density, field-drying behaviour and combustion characteristics are affected by the simultaneous harvest of straw and chaff. Field experiments were conducted in 2009 for long- and short-stalked winter wheat crops. Combine harvesting was carried out with 2 different types of combine harvesters. A high-density baler was used to bale the crop residues. Mixing chaff in with the straw swath by combine harvesting gave a lower initial moisture content compared with straw only. The density and the weight of each bale were not affected by the treatments. ...

International Nuclear Information System (INIS)

New five complexes of the type of [RuL sub(3-x)(dmby) sub(x)]X sub(2)(x = 1,2,3, L = 2,2'-bipyridyl or 1,10-phenanthroline, dmby = 3,3'-dimethy1-2,2'-bipyridyl, X = halide ion) have been synthesized in order to investigate the effects of two methyl groups of dmby on the absorption and emission spectra, luminescence quantum yields, and lifetimes. Values of the radiative and nonradiative rate constants have been calculated from these data at 77K. Although the absorption and emission maxima and the lifetimes are not much affected by the dmby ligand substitution, the molar extinction coefficients and emission quantum yields are decreased compared with trischelated complexes of the parent bipyridyl or phenanthroline ligands. At 25"0C the emission yields of the complexes containing dmby decrease by 3 - 4 orders of magnitude than at 77K. Possible causes of the decrease in the quantum yields are discussed. ...

Energy Technology Data Exchange (ETDEWEB)

We have developed a method for the synthesis of C-11 iodoantipyrine. Carbon-11-labeled methyl iodide, prepared from /sup 11/CO2, was used to methylate 3-methyl-1-phenyl-2-pyrazolin-5-one to form C-11 antipyrine. Following silica-gel column chromatography and iodination, radiochemical purity of the C-11 iodoantipyrine was more than 99.5%, with a 10% yield and a specific activity of 30 mCi/mumol. Preliminary animal studies showed complete cerebral extraction and local cerebral blood-flow values that were within 4.6% of those obtained using C-14 iodoantipyrine. The C-11 analog, with positron emission tomography, will facilitate local cerebral blood-flow studies in human subjects.

Science.gov (United States)

Extensive laboratory and industrial tests are being conducted at the Western Siberian Iron and Steel Works (I and SW) on the adoption of preheating of coking. The present article describes the results of laboratory investigations of the effect of the free oxygen content in the gaseous heat carrier and the final charge preheating temperature on the technological properties of the charge and the quality of the blast furnace coke, as well as the yield and quality of the coking products: 1. An increase in the free oxygen concentration in the heat carrier to 8% degrades the strength properties of the coke - the crushability and abradability are increased. 2. Charge preheating to 200 to 250/sup 0/C, even with a low oxygen concentration in the heat carrier, is accompanied by degradation of the physical and mechanical properties of the coke. 3. The optimal temperature of charge preheating before coking at the Western Siberia I and SW was found to be in the 150 to 200/sup ...

Energy Technology Data Exchange (ETDEWEB)

An anaerobic fermenter-decanter for the purification of residual water from the sugar industry, with recovery of methane, consists of a tank with inclined walls, with a central agitator on a vertical shaft. A flexible cover anchored by its periphery to the walls of the tank and totally submerged forms a collecting pocket for the fermentation gases. The water to be purified is introduced, after being heated to about 35, towards the bottom of the tank near the agitator. A metal collecting bell with submerged edges and with the shaft of the agitator passing axially through it is connected by its edges to a central opening of the cover. The purification yields may exceed 90%.

International Nuclear Information System (INIS)

The production of radiopharmaceuticals used in positron emission tomography (PET) can require large amounts of activity at the start of synthesis in order to yield sufficient labeled material for clinical studies. Several investigators have developed remote and automated systems for the routine production of PET radiopharmaceuticals in order to reduce radiation exposure to personnel. Such devices, however, suffer from limited flexibility and can be relatively complicated in design. These systems are also limited to the production of a single or a few closely related compounds. Furthermore, changes in chemistry would require considerable modifications in hardware and/or software in order to bring the device back into operation. To circumvent the above limitations associated with the remote production of PET radiopharmaceuticals, the authors have investigated the use of laboratory robotics as a flexible alternative to the ...

International Nuclear Information System (INIS)

Single crystals of GdCl_3 doped with different concentrations of Ce"3"+ have been grown using the Bridgman-Stockbarger technique and their luminescence and scintillation properties were investigated. The luminescence spectrum of GdCl_3:Ce"3"+ is complex and consists of two bands with maxima at 350 nm and 370 nm. The maximal light yield in GdCl_3:Ce"3"+ was observed at #approx#1 mol% of Ce"3"+ (more than 38 000 ph/MeV).

International Nuclear Information System (INIS)

Polytetrafluoroethylene was obtained by radiation induced polymerization of tetrafluoroethylene in acetone at 195 K. An average diameter of the products was very small compared with commercial one; it was about 0.3 micro-meters. The yield was reached to 100% with a dose of 4 kGy. The crystallinity of the products is decreasing with increasing dose. The products become amorphous, for higher irradiation doses. It was found that PTFE obtained by irradiation of TFE in acetone at 195 K has branching structure. This was demonstrated by means of "1"9F MAS NMR. (Author)

Energy Technology Data Exchange (ETDEWEB)

A useful method for preparing radioiodinated photoaffinity labels from alkyl anilines which offer significant advantages over present methods is described. The one-pot synthesis gives good radiochemical yields (40-64%) of pure, high specific activity (350-1500 mCi/{mu}mol) {sup 124}I labelled iodaryl azides while minimising manipulation of radioactive materials. Purification of the ({sup 125}I)iodoazido photoaffinity labels is achieved by high performance liquid chromatography. (author).

Energy Technology Data Exchange (ETDEWEB)

Coal liquefaction investigations required the availability of model compounds for mechanistic investigations. Towards this end, IITRI was funded to develop an approach for the synthesis of one of the target compound. This study was carried out in several phases as outlined here. Initial synthetic investigations on obtaining 2-tetrolol was carried out using high pressure and temperature reduction with Raney nickel catalyst. The next step consisted in incorporation of a hydroxymethyelene group at the C-3 position. This was successfully carried out utilizing 2-tetrolol, formaldehyde, and calcium oxide. An alternate improved method was developed using 3-carboxyl-2-naphthol. This required less time, gave a cheer product in higher yield. Efforts at the introduction of a chloromethylene group only yielded polymeric material or starting material in spite of protection the phenolic group by various groups. They ...

Energy Technology Data Exchange (ETDEWEB)

For IGCC, the primary investment is too high due to the demand of high gasification efficiency. For PFBCC, the thermal efficiency is too low due to the relatively low turbine inlet temperature and the hot working medium of the gas turbine is not easy to clean. A new scheme is proposed for coal fired combined cycle to overcome the main drawbacks of IGCC and PFBCC. The research targets are developing a new cycle construction of coal fired combined cycle to raise the efficiency and reduce the primary investment. Actually, the new scheme is a synthesis of some existing proposals. It adopts partial gasification to reduce the primary investment of the gasification equipment. The un-gasified surplus solid is then fed to a pressurized fluidized bed boiler, but adopting Curtiss Wright type external combustion to lower the ash content in the working medium. The gas fuel from the partial gasifier is combusted in a top combustor to ...

Energy Technology Data Exchange (ETDEWEB)

The KENTORT II process includes integral fluidized bed zones for pyrolysis, gasification, and combustion of the oil shale. The purpose of this program is to design and test the KENTORT II process at the 50-lb/hr scale. Along with the major activity of assembling the components of the 50-lb/hr retort, work was also completed in other areas this quarter. Basic studies of the cracking and coking kinetics of model compounds in a fixed bed reactor were continued. Additionally, as part of the effort to investigate niche market applications for KENTORT II-derived products, a study of the synthesis of carbon fibers from the heavy fraction of KENTORT II shale oil was initiated.

Energy Technology Data Exchange (ETDEWEB)

Hydrocarbon synthesis during CO hydrogenation over Pd/M-ZSM5 (M=H,Na,La) and Pd/SiO/sub 2/ has been investigated. Overall activity depended on the cation-exchanged form of the support and decreased in the order Pd/La-ZSM5 = Pd/Na-ZSM5 > Pd/H-ZSM5 > Pd/SiO/sub 2/. The zeolite-supported catalysts showed high selectivity towards saturated C/sub 2/-C/sub 6/ hydrocarbons, whereas Pd/SiO/sub 2/ favored methanol production. Increasing temperature and H/sub 2//CO feed ratio led to higher reaction rates, lower yields of C/sub 2/-C/sub 6/ products, and increased lighter hydrocarbons. A mechanical mixture of Pd/SiO/sub 2/ and Na-ZSM5 showed similar product distribution as Pd/Na-ZSM5. Infrared spectra of the catalysts under reaction conditions indicate the presence of adsorbed oxygenates on the zeolite. Changes in the IR bands during the initial stages of the reaction suggest that surface species on the zeolite are not methanol ...

Energy Technology Data Exchange (ETDEWEB)

The Synthesis Gas From Manure (SGFM) pilot plant was constructed at Texas Tech University to evaluate the gasification of cattle feedlot manure. A study of gas yield and composition as a function of operating conditions was performed. This report presents the results of a comparison of feedstocks other than manure in the pilot plant. Oak sawdust was the superior feedstock tested in terms of both gas yield and operability. Corn stover and mesquite were comparable and presented some handling problems. Cotton gin trash was unacceptable due to low-temperature ash fusion in the reactor. The gas yield from oak sawdust varied from 0.8 to 1.7 1/gm DAF feed at average temperatures of 650 to 770/sup 0/C. The gas contained approximately 15% hydrogen and 40% carbon monoxide by volume. It also contained 5 to 8% methane and 2 to 5% ethylene. All of these results were obtained using steam and air as the gasifying ...

Science.gov (United States)

... projectile. Descriptors : *Combustible cartridge cases, *Patents, Laminates, Ammunition propellants, Nitrocellulose. Subject ...

Energy Technology Data Exchange (ETDEWEB)

CuO/bentonite and CuO-BHA nanocomposites were studied as oxygen carriers in chemical-looping combustion (CLC) of simulated synthesis gas. Global reaction rates of reduction and oxidation, as the function of reaction conversion, were calculated from 10-cycle oxidation/reduction tests utilizing thermogravimetric analysis at atmospheric pressure between 700 and 900{degree}C. It was found that the reduction reactions are always faster than oxidation reactions; reaction temperature and particle size do not significantly affect the reaction performance of CuO/bentonite. Multicycle CLC tests conducted in a high-pressure flow reactor showed stable reactivity for production of CO{sub 2} from fuel gas at 800 and 900{degree}C and full consumption of hydrogen during the reaction. Results of the tapered element oscillating microbalance showed a negative effect of pressure on the global rates of reduction-oxidation reactions at higher fractional conversions. ...

Energy Technology Data Exchange (ETDEWEB)

In relation to coal gasification and combustion under high pressure as highly efficient coal utilization, the effect of total pressure and sintering on the SO2 capture ability of Ca-ion exchanged coal and other desulfurizing agents were studied. In experiment, specimens were filled into a small pressurized reactor to heat them under high-pressure N2 atmosphere. After the completion of combustion reaction of char at 850{degree}C, SO2, CO2 and CO gases were measured at an outlet while flowing SO2/N2. As the experimental result, all of the S content in Ca-ion exchanged coal was not absorbed by Ca content in coal during pyrolysis and combustion, resulting in discharge of 36% of the S content. Since Ca-ion exchanged coal is fast in combustion reaction, most of the S content was desulfurized by coal ash. The ash content yielded from Ca-ion exchanged coal was more excellent in SO2 capture ...

Energy Technology Data Exchange (ETDEWEB)

An LPP ignition timing control is described for an internal combustion engine including a combustion chamber, means effective to ignite a combustible charge within the combustion chamber and power output apparatus including a rotating crankshaft driven in response to the expansion of the combustible charge following the ignition thereof and having a predefined TDC rotational reference position, the engine being of the type having a normal combustion mode characterized by combustion pressure peaks compatible with closed loop LPP ignition timing control and an abnormal combustion mode which may not be so compatible.

Energy Technology Data Exchange (ETDEWEB)

The synthesis of (1',3'-{sup 3}H)4-(4'-azido-5',6',7',8'-tetrahydro-5'5'8',8'-tetramethyl-2'-anthracenyl)benzoic acid is described. This retinoid was designed as a photoaffinity probe of the receptor sites of cellular retinoic acid-binding protein and the nuclear retinoic acid receptor protein. The ({sup 3}H)azidoretinoid was prepared from 1,2,3,4-tetrahydro-1,1,4,4-tetra-methyl-7-(4-methylphenyl)-5-nitroanthracene in five steps in 15% yield (89% radiochemical purity by HPLC). {sup 1}H and {sup 3}H NMR was used to confirm the sites of {sup 3}H substitution on the ring. (author).

Energy Technology Data Exchange (ETDEWEB)

The synthesis of (3-{sup 15}N)-labeled adenine has been reported by several groups. Each of these syntheses followed essentially the same route, in which the {sup 15}N is introduced by nitration of 4-bromoimidazole under forcing conditions using ({sup 15}N)-HNO{sub 3}. The authors have devised an alternate route which uses an azo coupling reaction for introduction of the {sup 15}N and proceeds through the intermediacy of (5-{sup 15}N)-labeled 5-aminoimidazole-4-carboxamide (AICA). An unrelated route to the (5-{sup 15}N)-labeled 5-amino-imidazole ribonucleoside (AIRs) was recently reported. AICA is a versatile precursor, which is most commonly used for entry into the guanine or isoguanine families, although it is usually used as the AICA-riboside rather than the heterocycle itself. The authors have found that AICA also can be used for the adenine family by cyclization to hypoxanthine using diethoxymethyl acetate in DMF at reflux. Although these conditions are more ...

Energy Technology Data Exchange (ETDEWEB)

Oxygenated fuels increase fuel consumption due to their low enthalpy of combustion; however, their high antiknock index renders them suitable for use in engines with a high compression rate, increasing their thermal yield. This study evaluated the performance of biorenewable oxygenated fuels (ethanol and isoamyl alcohol) and partially renewable fuels (ETBE: ethyl tert-butyl ether, TAEE: tert-amyl ethyl ether and di-TAE: di-tert-amyl ether) with high degree of purity and in mixtures with automotive gasoline, based on tests with Otto cycle engines. Among the oxygenated fuels evaluated here, di-TAE was found to present the best characteristics of performance, both individually and in mixtures with gasoline. 40 refs., 5 figs., 2 tabs.

British Library Electronic Table of Contents (United Kingdom)

Determination of the radiocarbon (14C) content of airborne particulate matter yields insight into the proportion of the carbonaceous material derived from fossil and contemporary carbon sources. Daily samples of PM2.5 were collected by high-volume sampler at an urban background site in Birmingham, UK, and the fraction of 14C in both the total carbon, and in the organic and elemental carbon fractions, determined by two-stage combustion to CO2, graphitisation and quantification by accelerator mass spectrometry. OC and EC content was also determined by Sunset Analyzer. The mean fraction contemporary TC in the PM2.5 samples was 0.50 (range 0.27-0.66, n=26). There was no seasonality to the data, but there was a positive trend between fraction contemporary TC and magnitude of SOC/TC ratio and fo...

British Library Electronic Table of Contents (United Kingdom)

It was demonstrated that R 2?R 4 saturated monohydric alcohols can be synthesized from CO and H2 in the presence of Fe catalysts containing a carbon support of the Sibunit type with granule sizes of 3?5, 1?2, and 0.05?0.1 mm in a fixed-bed reactor at 3 MPa and 240?300?C. It was found that the activity of Fe/Sibunit catalysts and their selectivity for the formation of liquid synthetic products increased with the size of granules and the amount of iron. The catalysts make it possible to obtain fatty alcohols, in which the fraction of R 2?R 4 alcohols is as high as 75%, in yields to 56 g/m3.

International Nuclear Information System (INIS)

Eu"3"+ and Tb"3"+ complexes with novel branched calix[4]arene ligands incorporating 2,2' -bipyridine subunits functionalized in the 6- or 5,5'-positions have been synthesized and their photophysical properties investigated. High luminescence intensity was obtained for the Eu"3"+ complex of the calix[4]arene ligand carrying four 5,5' -substituted- 2,2' -bipyridines, which has high molar extinction coefficients (#epsilon#_m_a_x 39 600 M"-"1 cm"-"1) and a high luminescence quantum yield (15%). (authors). 12 refs., 2 figs., 1 tab.

British Library Electronic Table of Contents (United Kingdom)

The dimercaptosuccinic acid metronidazole ester (DMSAMe) was synthesized and radiolabeled with 99mTc to form the 99mTc-DMSAMe complex in high yield. The radiochemical purity of the 99mTc-DMSAMe complex was over 90%, as measured by TLC and by HPLC, without any notable decomposition at room temperature over a period of 6?h. Its partition coefficient indicated that it was a lipophilic complex. The tumor cell experiment and the biodistribution in mice bearing S 180 tumor showed that the 99mTc-DMSAMe complex had a certain hypoxic selectivity and accumulated in the tumor with high uptake and good retention. The tumor/blood and tumor/muscle ratios increased with time, suggesting it would be a possible tumor hypoxia imaging agent.

Energy Technology Data Exchange (ETDEWEB)

The shallow Green River Formation oil shales in the southern part of Utah's Uinta Basin are potentially developable by strip mining or by subsurface techniques which take advantage of limited overburden. The resource of potential shale oil represented by the shallow deposits is evaluated in detail from corehole oil-yield data. Cross-sections are constructed to readily correlatable stratigraphic units selected to represent resources in the shallow shale. To define each unit, the thickness, average oil yield, and oil resource of each unit in each core are calculated. Contour maps constructed from these data define the resource variation across the shallow resource. By measuring areas enclosed in each resource unit within the defined limit of 200 feet (61 meters) of overburden, the resource represented by the shallow oil shale is evaluated. The total resource is measured as 4.9 billion barrels (779.1 billion liters) of potential shale oil ...

Science.gov (United States)

... More particularly, the invention relates to novel felted combustible cartridge cases of excellent tensile strength, water resistance and combustibility. ...

UK PubMed Central (United Kingdom)

The stereocontrolled total synthesis of 4-hydroxydictyolactone (4), a member of the xenicane diterpene family of natural products, is described. These studies feature the development...Full Text Available

ScienceCinema

...different sparking language english ? ...

Energy Technology Data Exchange (ETDEWEB)

The DOE Working Group for an Assessment of Coal-Gasification Research Needs (COGARN - coal gasification advanced research needs) has reviewed and evaluated US programs dealing with coal gasification for a variety of applications. Cost evaluations and environmental-impact assessments formed important components of the deliberations. We have examined in some depth each of the following technologies: coal gasification for electricity generation in combined-cycle systems, coal gasification for the production of synthetic natural gas, coal gasifiers for direct electricity generation in fuel cells, and coal gasification for the production of synthesis gas as a first step in the manufacture of a wide variety of chemicals and fuels. Both catalytic and non-catalytic conversion processes were considered. In addition, we have constructed an orderly, long-range research agenda on coal science, pyrolysis, and partial combustion in order to support applied ...

Science.gov (United States)

... Descriptors : *Combustible cartridge cases, *Ammunition components, *Manufacturing, Fabrication, Industrial production, Nitrocellulose, Adhesives ...

Science.gov (United States)

... Accession Number : ADD001040. Title : Process for Uniformly Depositing Resin in Combustible Cartridge Cases. Descriptive Note : Patent,. ...

Science.gov (United States)

A production method was developed to fibrillate commercial acrylic fiber suitable for the manufacture of combustible cartridge cases.

Science.gov (United States)

... Descriptors : *Combustible cartridge cases, *Nitrocellulose, *Propelling charges, *Ammunition containers, Felts, Munitions industry, Fibers, Acrylic ...

Science.gov (United States)

... Descriptors : *Combustible cartridge cases, *Water repellents, *Protective coatings, *Patents, Silica gel, Aluminum compounds, Binders ...

Science.gov (United States)

... ADA185428. Title : Combustible Cartridge Cases, an Account of the Current Technology and Proposals for Future Development. ...

Science.gov (United States)

... Abstract : The beater additive process for manufacturing combustible cartridge cases is superior to the solvent resin, post-impregnation process. ...

Science.gov (United States)

... Research on development of combustible cartridge cases for small arms was conducted in Germany during World War II. ...

Science.gov (United States)

... Descriptors : *Combustible cartridge cases, *Polymers, *Test equipment, *Patents, Combustion chambers, Breech mechanisms, Gas generating ...

Science.gov (United States)

PMID:21370327

Science.gov (United States)

No abstract prepared.

International Nuclear Information System (INIS)

Solid oxide fuel cell (SOFC) is a promising source of power generation in terms of conversion efficiency which is higher than the conventional one, as it is not limited by the Carnot efficiency. Theoretically, the SOFC have an efficiency of the order of 60-80 % but it is limited by the number of active side available for the reaction i.e. TPB (triple phase boundary) at the electrode-electrolyte interface which depends on the particle size of the materials employed during the fabrication of SOFC components (i.e. the method employed during the synthesis). Literally, there are several methods used in the syntheses of oxide materials such as conventional solid-state reaction, co-precipitation, hydrothermal rout, sol-gel and Glycine nitrate process (GNP) but among these GNP found to be effective over the other because of homogeneity, phase purity and smaller particle size of final product. In this work, the Nano-crystalline Ln_0_._6Sr_0_._4Co_0_._8Fe_0_._2O_3_-_#delta# ...

Energy Technology Data Exchange (ETDEWEB)

This book of proceedings reports on 7 papers on combustion chemistry and formation of pollutants presented during the workshop organized by the `Combustion and Flames` section of the French society of thermal engineers. The chemistry of combustion is analyzed in various situations such as: turbojet engines, spark ignition engines, industrial burners, gas turbines etc... Numerical simulation is used to understand the physico-chemical processes involved in combustion, to describe the kinetics of oxidation, combustion and flame propagation, and to predict the formation of pollutants. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

This study tried to reduce NO{sub x} and particulate emissions simultaneously in a high speed direct-injection diesel engine. Fuel-rich combustion was used to reduce NO{sub x} emission at initial combustion stage and high turbulence combustion was used to reduce particulate emission at diffusion combustion stage. Experiments were carried out to investigate the effects of high squish combustion chambers with small throat on combustion process and exhaust emissions. Results showed that in the high squish combustion chamber, both NO{sub x} and particulate emissions reduced with retarded injection timing. Endoscopic high speed photography was employed to analyze experimental results. In the original combustion chamber at the early combustion stage, the high luminosity flame tended to spread out of the ...

Energy Technology Data Exchange (ETDEWEB)

The information reported is for the period October I to December 31, 1993. During this quarter, activities were undertaken in Task 2. Oxygen concentrations were measured in the post-flame region of the entrained flow reactor. The sampling probe was used for the hot gas tests to sample the gas stream. Samples were injected into a gas chromatograph to determine the oxygen concentration. Results agreed with thermoequilibrium calculations that yield equilibrium compositions based on the stoichiometry of the feed gases. The axial temperature distribution along the reactor centerline was measured using a silica-coated platinum-rhodium thermocouple. Two coating techniques were tested and it was found that flame-plating silica to the thermocouple wires produced a thinner coating than a ceramic adhesive technique and therefore a smaller radiation correction. Other activities this quarter included the fabrication of a solids sampling probe support assembly and thermocouple ...

British Library Electronic Table of Contents (United Kingdom)

Schiff-base condensation of a equimolar proportion of diacetyl-monoxime monohydrazone and 1-methylimidazole-2-carboxaldehyde in methanol gives rise to the imidazole azine, 3-(1-methylimidazol-2-yl)methylenehydrazonobutan-2-one oxime(HL). Reaction of 1:1 stoichiometric proportion of HL with copper(II)perchlorate hexahydrate in methanol yields a dimeric oximato bridged copper compound, [Cu2L2(H2O)2](ClO4)2 (1). The compound is characterized by C, H and N analyses, FT-IR, ESI?MS, conductivity measurement, UV?Vis spectra and X-ray single crystal diffraction. The title compound (1) crystallizes in the monoclinic space group P21/c with a?=?6.8533 (8), b?=?18.413 (2), c?=?11.7399 (14) ?, ??=?93.685 (2)?, V?=?1478.4 (3) ?3 and Z?=?2. The geometry around each copper center is distorted square pyram...

British Library Electronic Table of Contents (United Kingdom)

A conjugate of 6-hydrazinopyridine-3-carboxylic acid (HYNIC) with the amino analogue of metronidazole (MN) was synthesized through a multiple-step reaction. HYNIC-MN could be labeled easily and efficiently with 99mTc using N-(2-hydroxy-1,1-bis(hydroxymethyl)ethyl)glycine (tricine) and ethylenediamine -N,N?-diacetic acid (EDDA) as coligands to form the 99mTc?HYNIC?MN complex in high yield (>95%). Its partition coefficient indicated that it was a good hydrophilic complex. The tumor cell experiment showed that the 99mTc?HYNIC?MN complex had a certain hypoxic selectivity. The biodistribution studies of 99mTc?HYNIC?MN in Kunming mice bearing S180 tumor showed a favorable tissue distribution profile with high tumor uptake, and low or negligible accumulation in non-target organs, suggesting 99mTc...

International Nuclear Information System (INIS)

As part of our program in radiopharmaceutical chemistry we have prepared and evaluated a series of radioiodinated 1-alkyl-4-phenylpiperazines as potential brain-imaging agents. The compounds were chosen on the basis of their synthetic versatility, activation toward electrophilic substitution, and ease of purification. The intermediates 1-6 were readily obtained and converted to the corresponding radioiodinated products 7-12 in 76-91% isolated radiochemical yields. The tissue distribution in rats indicated that the 1-N-butyl derivative 9 possesses the best combination of brain uptake (0.28-0.35% ID X kg/g), retention, and selectivity (brain/blood greater than 20) over the 4-h evaluation period. A subsequent imaging and tissue distribution study in the dog using 131I-labeled 9 supported the results observed in the rat and suggested the potential of this agent as a brain-imaging agent.

British Library Electronic Table of Contents (United Kingdom)

Homozygous transgenic cotton (Gossypium hirsutum L.) plants that accumulated glycinebetaine (GB) in larger quantities were more tolerant to salt than wild-type (WT) plants. Four transgenic lines, namely 1, 3, 4, and 5, accumulated significantly higher levels of GB than WT plants did both before and after salt stress. At 175 and 275?mM NaCl, seeds of all the transgenic lines germinated earlier and recorded a higher final germination percentage, and the seedlings grew better, than those of the WT. Under salt stress, all the lines showed some characteristic features of salt tolerance, such as higher leaf relative water content (RWC), higher photosynthesis, better osmotic adjustment (OA), lower percentage of ion leakage, and lower peroxidation of the lipid membrane. Levels of endogenous GB in ...

International Nuclear Information System (INIS)

Paper describes a new procedure to synthesize a pharmaceutical containing "2"1"1At. "2"1"1At"- anion was found to bind strongly with Rh"3"+ cation complexing with a thio-ether ligand - 1,5,9,13-tetratiacyclohexadecane-3,11-diol (16-S4-diol). One made use of "1"3"1I isotope to seek for the optimal conditions of the reaction. The derived complexes were studied by means of the paper electrophoresis, the ion exchange, the surface chromatography. One studied the kinetics of "1"3"1I"- anion binding with Rh(16-S4-diol), the dependence of the yield of "1"3"1I-Rh(16-S4-diol) forming complex on the temperature. the acidity of the reaction mixture and the concentration of the reagents. On the basis of the determined conditions of the synthesis one prepared "2"1"1At-Rh(16-S4-diol) complex by more astatide ("2"1"1At"-) to the equivalent amounts of RhCl_3 and tetra-thio-ether (16-S4-diol). One studied its behaviour

Energy Technology Data Exchange (ETDEWEB)

A thermophotovoltaic (TPV) generator for electric vehicles has been designed and developed. In this paper we focus on the combustion system and the heat regenerator. The system has been designed to work as a range extender for electric vehicles. This solution would provide energy always available on the vehicle, which would run even if the battery level were low. Several configurations for the burner and for the heat exchanger have been investigated and a comparison of these is presented. The different solutions have been studied both theoretically and experimentally. In this paper, we report on the work carried out to build a TPV device capable of yielding 6 kW of electric power to recharge the battery pack of an electric city-car. The project has been divided into four steps: (1) pre-design of different configurations of the burner and heat exchanger using non-commercial software 'TPV Design Tool 1.0'; (2) testing of the ...

International Nuclear Information System (INIS)

The central benzodiazepine receptor tracer [N-methyl-"1"1C]iomazenil (Ro 16-0154) was synthesized by alkylation of the desmethyl precursor noriomazenil with ["1"1C]methyl iodide. The ["1"1C]CH_3I (prepared by reduction of ["1"1C]CO_2 with LiAlH_4 followed by reaction with HI) was reacted with noriomazenil inN,N -dimethylformamide and Bu_4N"+OH"- for 1 min at 80 deg. C and purified by HPLC (C_1_8, 34% CH_3CN/H_2O, 7 mL/min). The product was obtained with synthesis time 35 #+-# 5 min (mean #+-# SD, n = 7), radiochemical yield (EOB) 36 #+-# 16%, radiochemical purity 99 #+-# 1%, and specific activity 5100 #+-# 2800 mCi/#mu#mol. Absorbed radiation doses were calculated from previously acquired human biodistribution data. The urinary bladder wall received the highest dose (0.099 mGy/MBq) for 4.8 h voiding interval and the effective dose equivalent was 0.015 mSv/MBq. After i.v. injection of ["1"1C]iomazenil in an adult baboon or healthy human ...

Energy Technology Data Exchange (ETDEWEB)

Water model experiments were conducted to develop a two-stage stirring method for obtaining higher yields and a more uniform distribution of graphite particles in copper alloys. This was followed by several melts for synthesis of copper-graphite alloys in which Ti was used as a wetting agent to improve the wettability of graphite in the copper melt. In the first stage, a vortex method was employed to facilitate the addition of graphite particles into the copper melt. In the second stage, a specially designed stirrer was used for uniform particle distribution while avoiding the formation of vortex in the melt. The two-stage stirring was found to considerably improve the recovery of graphite, over those obtained with the prior practice of single-stage stirring and resulting in a more uniform particle distribution. In addition, graphite recoveries increased with increasing Ti content in the range investigated. Floatation, fluidity, and directional ...

Science.gov (United States)

The state of the art of our understanding of combustible cartridge cases is presented. The report, after a background section, discusses the models that exist today and presents new models of combustible cartridge case burning. Following a summary of expe...

Energy Technology Data Exchange (ETDEWEB)

Apparatus and a method of introducing a primary fuel, which may be a coal water slurry, and a high combustion auxiliary fuel, which may be a conventional diesel oil, into an internal combustion diesel engine comprises detecting the load conditions of the engine, determining the amount of time prior to the top dead center position of the piston to inject the main fuel into the combustion chamber, and determining the relationship of the timing of the injection of the auxiliary fuel into the combustion chamber to achieve a predetermined specific fuel consumption, a predetermined combustion efficiency, and a predetermined peak cylinder firing pressure. 19 figures.

Science.gov (United States)

... Combustible ..... 24 - S-CRET/DISCREET Page 33. SECRET/D ISCREET Combustible Cartridge Cases CONFIDENTIAL ...

International Science & Technology Center (ISTC)

Investigation of the Macrokinetics and Energy of Self-Oscillatory Processes of Gasless Combustion of Solid Fuel Mixtures Proposed for the Design of Short-Term Thermal and Electrical Sources

Energy Technology Data Exchange (ETDEWEB)

A burner system particularly useful for downhole deployment includes a tubular combustion chamber unit housed within a tubular coolant jacket assembly. The combustion chamber unit includes a monolithic tube of refractory material whose inner surface defines the combustion zone. A metal reinforcing sleeve surrounds and extends the length of the refractory tube. The inner surface of the coolant jacket assembly and outer surface of the combustion chamber unit are dimensioned so that those surfaces are close to one another in standby condition so that the combustion chamber unit has limited freedom to expand with that expansion being stabilized by the coolant jacket assembly so that compression forces in the refractory tube do not exceed about one-half the safe compressive stress of the material; and the materials of the combustion chamber unit are selected to ...

Science.gov (United States)

The overall objective of this project is the three phase development of an Early Entrance Coproduction Plant (EECP) which uses petroleum coke to produce at least one product from at least two of the following three categories: (1) electric power (or heat), (2) fuels, and (3) chemicals using ChevronTexaco's proprietary gasification technology. The objective of Phase I is to determine the feasibility and define the concept for the EECP located at a specific site; develop a Research, Development, and Testing (RD&T) Plan to mitigate technical risks and barriers; and prepare a Preliminary Project Financing Plan. The objective of Phase II is to implement the work as outlined in the Phase I RD&T Plan to enhance the development and commercial acceptance of coproduction technology. The objective of Phase III is to develop an engineering design package and a financing and testing plan for an EECP located at a specific site. The project's intended result is to provide ...

Science.gov (United States)

Robert A. Martock. Cleveland State University, Cleveland, Ohio. Synthesis and Structural Characterization of a. Novel Indium Mercapto Derivative. [Clln(SCH. 2 ...

UK PubMed Central (United Kingdom)

A one-pot multicomponent procedure for the synthesis of highly functionalized pyrrolidine rings through a domino...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper investigated the effect of hydrogen (H{sub 2}) addition on the combustion process of a heavy-duty diesel engine. The addition of a small amount of H{sub 2} was shown to have a mild effect on the cylinder pressure and combustion process. When operated at high load, the addition of a relatively large amount of H{sub 2} substantially increased the peak cylinder pressure and the peak heat release rate. Compared to the two-stage combustion process of diesel engines, a featured three-stage combustion process of the H{sub 2}-diesel dual fuel engine was observed. The extremely high peak heat release rate represented a combination of diesel diffusion combustion and the premixed combustion of H{sub 2} consumed by multiple turbulent flames, which substantially enhanced the combustion process of H{sub 2}-diesel dual fuel engine. However, the ...

Energy Technology Data Exchange (ETDEWEB)

This review examines the characteristics of the compression-ignition type of dual-fuel engine and the combustion phenomena that affect these characteristics. The specific areas covered involve normal combustion processes, the nature and origin of engine knock, operation with LNG, and the effect of intake temperature on combustion efficiency and exhaust composition.

Science.gov (United States)

... cure. Descriptors : *Combustible cartridge cases, *Ammunition propellants, Patents, Binders, Curing agents, Additives. Subject ...

Energy Technology Data Exchange (ETDEWEB)

Analysis of the coke gas combustion porcess is presented. Standard kinetic relationships were utilized. Calculations were performed for coke gas with high and low content of H/sub 2/ and for blasting air 20 and 100/sup 0/C. Temperature relationships, composition of gas combustion products and release of nitrogen oxides were determined. Results are analyzed which will make it possible to control the composition of combustion products.

Science.gov (United States)

... TEMPERATURE, PRESSURE MEASUREMENT, GUN CHAMBERS, COMPACTING, COMBUSTIBLE CARTRIDGE CASES, FLASH RADIOGRAPHY ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... PADS(CUSHIONS), OBTURATION(BALLISTICS), BUTYL RUBBER, COMBUSTIBLE CARTRIDGE CASES, PHOSPHORUS COMPOUNDS. ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

Nano-particles of CeO{sub 2} with the smallest average particle size (18.7 nm) and spherical morphology were obtained from a mixture solution of Ce(NO{sub 3}){sub 3}{center_dot}6H{sub 2}O, citric acid, polyvinyl alcohol by an auto-combustion process exploiting sol-gel as precursors. The course of size control and shape control by polyvinyl alcohol was examined in detail. A transmission electron microscopy (TEM) and an atomic force microscopy (AFM) were employed to characterize the particle-size and morphology of CeO{sub 2} particles. In addition, a sort of nano-metric solid acid SO{sub 4}{sup 2-}/CeO{sub 2} based on CeO{sub 2} nano-particles was prepared by macerating, filtering, drying and calcining processes. The particle-size of SO{sub 4}{sup 2-}/CeO{sub 2} was also assessed by TEM. The composition of SO{sub 4}{sup 2-}/CeO{sub 2} was analyzed by X-ray diffraction (XRD) and infrared spectra (IR). The influencing factors in the formation of SO{sub 4}{sup ...

Energy Technology Data Exchange (ETDEWEB)

Simultaneous reduction of NO{sub x} and particulate emissions in a direct-injection diesel engine has been realized experimentally with a high squish combustion chamber. The purpose of this study is to investigate the effects of high squish combustion chamber on combustion process in detail. Engine CFD code FREC was used for the analysis. The results show the followings. (1) Compared with standard toroidal chamber, high squish chamber generates high turbulence due to strong squish and large expansion flow is caused in the cavity. (2) Rich and high-turbulence combustion, which forms ring area in the cavity under squish lip, continues during the combustion. (3) The high squish combustion chamber keeps fuel long in the cavity and less hid spreads out to the cold clearance volume. (4) For the condition of retarded injection timing, the effect of high squish is ...

Energy Technology Data Exchange (ETDEWEB)

Brief item.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

The heterogeneous solid catalyst, mercaptopropylsilica (MPS), has been prepared by a modified procedure in water and its structure confirmed by solid state carbon-13 CP-MAS NMR spectrum. This catalyst has been efficiently utilized for the synthesis of a wide variety of tri-, tetrasubstituted imidazoles and their bis-analogues at room temperature. The protocol was further explored for the synthesis of the drug trifenagrel.

DEFF Research Database (Denmark)

ATPase, endoplasmic reticulum, calcium, ischaemia

International Nuclear Information System (INIS)

... odd nuclei organic compounds radiation effects radioisotopes synthesis

Energy Technology Data Exchange (ETDEWEB)

A nitrogen oxides decreasing combustion method comprising: mixing a fuel and air with each other; bringing the mixture obtained into contact with a packed catalyst; and adding a fresh supply of the fuel to the stream obtained to form a mixed gas and causing the mixed gas to undergo non-catalytic thermal combustion, characterized in that only a catalytic reaction or combustion occurs at the packed catalyst; the temperature of the packed catalyst is kept lower than the ignition temperature of the mixture; the adiabatic flame temperature which is reached by the non-catalytic thermal combustion of the mixed gas is lower than the temperature at which the nitrogen oxides occur. 39 figs.

Energy Technology Data Exchange (ETDEWEB)

A three-dimensional mathematical model has been developed as a tool for furnace structure design and operation conditions optimization when the straw combustion is in oxygen-enriched or conventional air atmospheres. Mathematical methods have been used based on a combination of FLIC (A fluid Dynamic Incinerator Code) code for the in-bed incineration and commercial software FLUENT for the over-bed combustion. Oxygen-enriched atmospheres promote the destruction of most pollutants due to the high oxygen partial pressures and temperatures, which is reflected by very low residual amounts of organic combustion by-products in the bottom ash and flue gas of the straw-fired boiler unit. The predictions indicated that the maximum combustion temperature is around 1500 K, CO emission is 201 vppm and O{sub 2} concentration is about 6.9 vol% at furnace exit, and it is shown that mathematical models can serve as a ...

Energy Technology Data Exchange (ETDEWEB)

In order to realize simultaneous reduction of NO{sub x} and Particulate emissions, effects of combustion chamber geometry were investigated in a high speed direct-injection diesel engine. The reentrant combustion chambers with different throat diameter were compared in terms of engine performance, combustion characteristics and emissions such as NO{sub x}, particulate and THC. The phenomena of combustion process were also observed with endoscopic high speed photography. The results showed that when the throat diameter of a reentrant combustion chamber was reduced to an extent, NO{sub x} and particulate decreased simultaneously due to retarded injection timing and the intensified squish. (author)

International Nuclear Information System (INIS)

Biomass combustion is an important part in a sustainable energy system, but as well a source of submicron (particles < 1 #mu#m) particles in the air. Consequently, to obtain a good air quality together with increased biomass combustion there is a need for a better understanding of particle formation. This work is a part of a larger project about formation and emissions of particles from biofuel combustion. The report includes the work performed in the project during the year 2004. The aim of the project is to describe the release of inorganic components, which cause particle emissions, during combustion of single fuel particles of biofuel, e.g. wood pellets. The work is carried out by emission measurements, systematic combustion experiments and modelling work. The results are expected to contribute to the understanding of which parameters that influence the formation of fine ...

Energy Technology Data Exchange (ETDEWEB)

The combustion of forestry residues and of straw are dealt with in relation to the following: Agricultural Applications; Industrial Applications; Design; Performance and Properties; Economic Aspects; Environmental Aspects and Research programs.

Science.gov (United States)

An investigation was conducted to determine the cause of coating residue found in the test gun chambers during qualification firing of 120-mm combustible cartridge case (CCC) ammunition for the MlAl/A2 main battle tank. The CCC is coated with a clear epox...

Energy Technology Data Exchange (ETDEWEB)

The methodology of constructing Nomographs for easy determination of heat loss due to incomplete combustion for a particular fuel has been presented in this article. The authors have worked out the Nomograph for jute stick and paddy straw.

Science.gov (United States)

The procedure describes the procedures to be used in evaluating consumable and combustible cartridge cases. Included are ballistic tests, environmental tests, adverse condition tests, fungus resistance tests, drop tests and safety tests. (Author)

Science.gov (United States)

Combustible cartridge cases are at present produced either by the beater additive or by the post impregnation process. The literature covering these techniques, which basically follow the concept of fibre moulding and/or papermaking, is reviewed. The vari...

International Science & Technology Center (ISTC)

Development of New Resource-Saving Technologies for Ceramic Material Production: High resistant Pigments, Heat Shielding, Plasters, Filters, etc.; by the Method of Controllable Thermosynthesis in Combustion Wave Using Industrial Metal-Containing Wastes

Energy Technology Data Exchange (ETDEWEB)

Positron emission tomography (PET) imaging of {beta}-amyloid (A{beta}) plaques in the brain is a potentially valuable tool for studying the pathophysiology of Alzheimer's disease (AD). It may also be applicable for measuring the effectiveness of therapeutic drugs aimed at lowering A{beta} plaques in the brain. We have successfully reported a series of {sup 18}F-labeled fluoropegylated stilbenes for PET imaging studies. Encouraging results clearly demonstrated the usefulness of {sup 18}F-labeled stilbenes as potential A{beta} plaque-imaging agents. In the present study, we applied a similar approach to a styrylpyridine backbone structure. Among all derivatives examined (E)-2-(2-(2-(2-fluoroethoxy)ethoxy)ethoxy)-5-(4-dimethylaminostyryl) -pyridine (2) displayed high binding affinity in postmortem AD brain homogenates (K {sub i}=2.5{+-}0.4 nM, with [{sup 125}I]IMPY as radioligand). No-carrier-added [{sup 18}F]2 was successfully prepared by [{sup 18}F]fluoride displacement of the ...

Energy Technology Data Exchange (ETDEWEB)

The symmetrical complexes [{sup 99m}Tc][TcN(R{sub 2}PS{sub 2}){sub 2}] [R = CH{sub 3}, CH{sub 2}CH{sub 3}, CH{sub 2}CH{sub 2}CH{sub 3}, CH{sub 2}(CH{sub 3}){sub 2}], and the unsymmetrical complex [{sup 99m}Tc][TcN(Me{sub 2}PS{sub 2})(Et{sub 2}PS{sub 2})] have been prepared, at tracer level, through a two-step procedure involving the preliminary formation of a prereduced technetium nitrido intermediate followed by substitution reaction onto this species by the appropriate dithiophosphinate ligand [R{sub 2}PS{sub 2}]Na. The chemical identity of the resulting complexes have been established by comparison with the corresponding {sup 99}Tc-analogs prepared, at macroscopic level, by reacting the complex [{sup 99}TcNCl{sub 4}] [n-Bu{sub 4}N] (n-Bu = n-butyl) with an excess of ligand in methanol, and characterized by elemental analyses and spectroscopic techniques. The complexes are neutral and lipophilic, and possess a square pyramidal geometry, with an apical Tc N group and two ...

Science.gov (United States)

The optimal concentrations of nutrient medium components, aeration conditions, and pH providing for maximum biomass yields, as well as fumarase and L-aspartase activities, during submerged cultivation of Erwinia sp. were determined. The data showed that different concentrations of carbon source (molasses) and pH of the nutrient medium were required to reach the maximum fumarase and L-aspartase activities. Calculations performed by application of the additive lattice model suggested that the combination of these optimized factors would result in 3.2-, 3.4-, and 3.8-fold increases as compared to the experimental means in Erwinia sp. biomass, and L-aspartase and fumarase activities, respectively. The conditions of the fumaric acid biotransformations into L-malic and L-aspartic acids were optimized on the basis of intact Erwinia sp. cells, a fumarase and L-aspartase producer. In the cases of fumarate transformation into L-malic acid and of fumarate transformation into ...

Energy Technology Data Exchange (ETDEWEB)

As an explosion develops in the collapsed core of a massive star, neutrino emission drives convection in a hot bubble of radiation, nucleons, and pairs just outside a proto-neutron star. Shortly thereafter, neutrinos drive a wind-like outflow from the neutron star. In both the convective bubble and the early wind, weak interactions temporarily cause a proton excess (Y{sub e} {approx}> 0.50) to develop in the ejected matter. This situation lasts for at least the first second, and the approximately 0.05-0.1 M{sub {circle_dot}} that is ejected has an unusual composition that may be important for nucleosynthesis. Using tracer particles to follow the conditions in a two-dimensional model of a successful supernova explosion calculated by Janka, Buras, and Rampp (2003), they determine the composition of this material. most of it is helium and {sup 56}Ni. The rest is relatively rare species produced by the decay of proton-rich isotopes unstable to positron emission. In the absence of ...

Energy Technology Data Exchange (ETDEWEB)

The authors have examined the pyrolysis of Argonne samples of Wyodak and Illinois No. 6 coal in argon, undecane, Tetralin, and water. The effects of the pyrolysis on individual particles of coal were monitored visually in a cell with diamond windows capable of operation to temperature and pressures in excess of 500{degrees}C and 3000 psi. The changes in the particles from ambient to 460{degrees}C were recorded in real time on video tape, and images were then taken from the tape record and analyzed. The study showed that in argon both coals developed tars at 350{degrees}-370{degrees}C. The tars then quickly evaporated, leaving core particles remarkably similar in size and shape to the initial particles. These observations suggest that coal does not melt nor become fully liquid when heated. Nor does the softened coal undergo crosslinking to generate coke. Rather the simple loss of volatiles leaves behind the core residue as coke. Contrary to the common view, there appears to be no link ...

International Nuclear Information System (INIS)

An improved labeling procedure for peptides attached to organometallic 99mTc(III) '4+1' mixed-ligand complexes in which the radiometal is coordinated by a tripodal tetradentate chelator 2,2',2''-nitrilotriethanethiol (NS3) and a monodentate isocyanide ligand is presented. The labeling procedure was evaluated by the synthesis of [99mTc(NS3)(L2-RGD)]. The containing radiopharmaceutically interesting RGD-peptide cyclo[Arg-Gly-Asp-D-Tyr-Lys] was modified with 4-isocyanobutanoic acid (L2) as linker conjugated to N6-Lys to get the monodentate ligand L2-RGD. The structural identity of the 99mTc-conjugate was confirmed by comparison to a Re reference compound. The Tc- and Re-conjugates had matching retention times under identical HPLC conditions. The 99mTc-labeling was performed in a novel one-step procedure using the eluate of a 99Mo/99mTc generator, NS3, the isocyanide modified peptide, SnCl2, Na2EDTA, mannitol and ascorbic acid in the reaction mixture. Using optimized ...

Science.gov (United States)

... CHANNELS, TWO PHASE FLOW, WAVES, IGNITERS, GAS FLOW, HOWITZERS, CARTRIDGE CASES, COMBUSTIBLE CARTRIDGE CASES. ...

Science.gov (United States)

... used their Phoenics code to simulate the effect of additives, such as talcum powder which was impregnated in combustible cartridge cases, on the ...

Science.gov (United States)

... Descriptors : *AMMUNITION, *CONTAINERS, *CARTRIDGES, *COMBUSTIBLE CARTRIDGE CASES, *CARTRIDGE CASES, *ANTITANK ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a nitrogen oxides decreasing combustion method which comprises: a first step of mixing a fuel and air with each other; a second step of bringing the mixture obtained in the first step into contact with a packed catalyst such that only catalytic combustion occurs; and a third step of adding a fresh supply of the fuel to a stream obtained from the second step to form a mixed gas and causing the mixed gas to undergo non-catalytic thermal combustion. The temperature of the packed catalyst is lower than the ignition temperature of the mixture and the adiabatic flame temperature of the mixed gas is lower than a temperature at which the nitrogen oxides occur.

Energy Technology Data Exchange (ETDEWEB)

A dual fuel engine control system for controlling the power output of a dual fuel compression ignition engine. The engine includes mixing means for combining an oxidizer and a primary fuel at a substantially constant ratio of oxidizer to primary fuel. The power output of the engine is controlled through the use of a throttle valve controlling the quantity of combustible mixture delivered to the combustion chamber. The fuel control system minimizes the quantity of ignition fuel required by controlling the quantity of combustible mixture rather than the fuel of air ratio. (author) figs.

Science.gov (United States)

... BODY WEIGHT, FEMALES, SEX, ORGANS(ANATOMY), NITROGUANIDINE, NITROGLYCERIN, COMBUSTIBLE CARTRIDGE CASES, FERTILITY. ...

Science.gov (United States)

... INDUSTRIAL PRODUCTION, MODULAR CONSTRUCTION, IGNITION, PLUGS, NITROCELLULOSE, COMBUSTIBLE CARTRIDGE CASES, FELTS ...

Science.gov (United States)

... reverse aeb 9 nescesmsy amI identify by block number) Provides procedures for evaluating metal, consumable, and combustible cartridge cases. ...

Energy Technology Data Exchange (ETDEWEB)

The authors investigated the effect of T-2 toxin on rat liver mitochondrial protein synthesis. Isolated rat liver mitochondria were supplemented with an S-100 supernatant from rat liver and an external ATP-generating system. An in-vitro assay employing cycloheximide, and inhibitor of cytoplasmic protein synthesis, and chloramphenicol, and inhibitor of mitochondrial protein synthesis, to distinguish mitochondrial protein synthesis from the cytoplasmic process. Amino acid incorporation into mitochondria was dependent on the concentration of mitochondria and was inhibited by chloramphenicol. The rate of uptake of tritium leucine into mitochondrial protein was unaffected by the addition of T-2 toxin and was not a rate-limiting step in incorporation. However, 0.02 micrograms/ml of T-2 toxin decreased the rate of protein synthesis inhibition correlated with the amount of T-2 toxin taken ...

UK PubMed Central (United Kingdom)

The accepted model of retroviral reverse transcription includes a circular DNA intermediate which requires strand displacement synthesis for linearization and creation of an integration-competent, long...Full Text Available

International Nuclear Information System (INIS)

There is renewed interest in the +6 oxidation state of iron, ferrate (VI) (FeVIO42-), because of its potential as a benign oxidant for organic synthesis, as a chemical in developing cleaner ('greener') technology for remediation processes, and as an alternative for environment-friendly battery cathodes. This interest has led many researchers to focus their attention on the synthesis of ferrate(VI). Of the three synthesis methods, electrochemical, wet chemical and thermal, electrochemical synthesis has received the most attention due to its ease and the high purity of the product. Moreover, electrochemical processes use an electron as a so-called clean chemical, thus avoiding the use of any harmful chemicals to oxidize iron to the +6 oxidation state. This paper reviews the development of electrochemical methods to synthesize ferrate(VI). The approaches chosen by different laboratories to overcome some of ...

UK PubMed Central (United Kingdom)

A new strategy is presented for the synthesis of graft copolymers using only the ring-opening metathesis polymerization (ROMP). From a ROMP-derived main chain, pendant maleimide functional groups...Full Text Available

UK PubMed Central (United Kingdom)

Cell suspension cultures of tomato, Lycopersicon esculentum Mill. cv VFNT-Cherry, produce phytochelatins (poly[γ-glutamylcysteinyl]glycines) when exposed to cadmium. The synthesis...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Research programs, presented at the contractor's review meeting on indirect liquefaction, are presented on the following topics: oxygenates (methanol) synthesis; Fischer-Tropsch synthesis; product upgrading; and process support engineering evaluations. A total of 18 reports are included. Individual projects are processed separately for the data bases. (CBS)

Energy Technology Data Exchange (ETDEWEB)

Adenosine triphosphate (ATP) is an indicator of living biomass in marine particulates. This report details the method used by Lawrence Berkeley Laboratory to analyze particulate ATP in samples taken from oligotrophic, tropical ocean waters. It represents a synthesis of previously published methods.

UK PubMed Central (United Kingdom)

This study examined the hypothesis that solid surfaces may stimulate attached bacteria to produce exopolymers. Addition of sand to shake-flask cultures seemed to induce exopolymer synthesis by a number...Full Text Available

UK PubMed Central (United Kingdom)

4-methylumbelliferone (4-MU) is a hyaluronic acid (HA) synthesis inhibitor with anticancer properties; the mechanism of its anticancer effects is unknown. We evaluated the effects of 4-MU on...Full Text Available

Science.gov (United States)

Solid fuels such as coal, wood, and crop straw supply some fraction of household cooking and heating fuel for more than one billion people in China. As these fuels do not generally combust cleanly in household stoves, their use levies large health and environmental burdens, particularly in rural regions. Production of clean-burning fuels from agricultural residue offers one prospect for mitigating health and social burdens imposed by household use of solid fuels. This dissertation explores the question: how might production of clean-burning household fuels from agricultural residues affect human health and social conditions in rural China? I approach this question from three perspectives. First, a technically plausible but currently unproven village-scale energy technology is explored in a scenario bounded by natural resources and substantiated by engineering specifications, estimates of indoor exposures to air pollution, and epidemiological analyses. This analysis ...

Energy Technology Data Exchange (ETDEWEB)

A phenomenological model is presented for prediction of the combustion characteristics of a quiescent chamber diesel engine. Predictions with the model have shown acceptable agreement with a range of experimental data. The major physical processes controlling combustion have been characterized, and the dominant role of air entrainment and turbulent mixing confirmed quantitatively. 45 refs.

Energy Technology Data Exchange (ETDEWEB)

Since the most efficient way to improve fuel economy in the part-load range is to increase the compression ratio, emphasis is placed on combustion chambers allowing high compression ratios combined with low octane requirements. According to Porsche experience, many demands can be met in the simplest manner by locating the combustion chamber in the piston crown. This configuration offers various advantages over its counterpart installed in the cylinder head. 24 refs.

Science.gov (United States)

Research continued on the synthesis of model compounds for coal liquefaction research. This report covers the actual laboratory investigation performed during the reporting period in order to attain the stated objective of the project, viz, the synthesis of a model compound containing tetrahydronaphthalene, naphthalene and phenyl moieties linked by methylene, ethylene and ether bonds. The overall synthetic approach aimed at obtaining the end product has been broken down into three major steps that involve the synthesis of three key reactive intermediates. These are: (1) 3,5-dimethyl-5-bromobenzyl chloride, (2) 1-chloromethylene-2-hydroxytetralin and (3) 2-chloromethylene-1-hydroxynaphthalene.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

A mixture of aminoacids was irradiated by a scattered proton beam, its energy varying from 4 to 6.6 MeV, by doses up to 5 x 10"1"1 proton/cm"2 for studying the potentiality of abiogenic synthesis of biologically important compounds in space. It was ascertained that increase in the radiation dose and reduction of proton energy involve increase in effectiveness both of destruction of the initial aminoacid (tryptophan, tyrosine, glycine) and synthesis of the relevant dipeptide. Essential influence of mineral substrate on abiogenic synthesis of natural nucleotides under the action of diverse energy sources was pointed out

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

We have recently shown the applicability of robotics to the synthesis of a positron-emitting radiopharmaceutical, namely 16#alpha#[F-18]fluoroestradiol-17#beta#, a breast tumor imaging agent. We now report the application of the robot to the synthesis of two additional radiopharmaceuticals, [F-18]spiroperiodol and [C-11]butanol. This achievement shows the power of a robot as a multifunctional automated device for the synthesis of several positron-emitting radiopharmaceuticals in limited laboratory space. (author).

Energy Technology Data Exchange (ETDEWEB)

This invention pertains to a Fischer Tropsch process for converting synthesis gas to an oxygenated hydrocarbon with particular emphasis on dimethyl ether. Synthesis gas comprising carbon monoxide and hydrogen are converted to dimethyl ether by carrying out the reaction in the presence of an alkali metal-manganese-iron carbonyl cluster incorporated onto a zirconia-alumina support.

Energy Technology Data Exchange (ETDEWEB)

From 1965 to 1980 ash content in anthracite from the Donbass supplied to power plants increased from 21.9 to 35.5%, moisture content increased from 7.6 to 10.1%, calorific value declined from 23.7 to 18.5 MJ/kg. Combustion of anthracite culm is stabilized by mazout combustion. Heat treatment of anthracite culm by means of plasma generators improves fuel quality. High temperature causes emission of volatile matter from anthracite and partial gasification of coke particles. Combustion of volatile matter from anthracite and coke is a reliable ignition method for anthracite culm. It also stabilizes combustion of pulverized anthracite. Heat treatment of about 20% anthracite by plasma generators reduces nitrogen oxide emission from a furnace by 30-40%. 5 refs.

Energy Technology Data Exchange (ETDEWEB)

Lean premixed combustion (LPC) of natural gas is of considerable interest in land-based gas turbines for power generation. However, modeling such combustors and adequately addressing the concerns of LPC, which include emissions of nitrogen oxides, carbon monoxide and unburned hydrocarbons, remains a significant challenge. In this paper, characteristics of published simulations of gas turbine combustion are summarised and methods of modeling turbulent combustion are reviewed. The velocity-composition PDF method is selected for implementation in a new comprehensive model that uses an unstructured-grid flow solver. Reduced mechanisms for methane combustion are evaluated in a partially stirred reactor model. Comprehensive model predictions of swirl-stabilised LPC of natural gas are compared with detailed measurements obtained in a laboratory-scale combustor. The model is also applied to industrial combustor ...

International Nuclear Information System (INIS)

Combustion noise, knock and ignition limits data are measured and presented for a dual fuel engine running on dual fuels of Diesel and three gaseous fuels separately. The gaseous fuels used are liquefied petroleum gas, pure methane and compressed natural gas mixture. The maximum pressure rise rate during combustion is presented as a measure of combustion noise, and the knocking and ignition limits are presented as torque output at the onset of knocking and ignition failure. Experimental investigation on the dual fuel engine revealed the noise generated from combustion, knocking and ignition limits for all gases at different design and operating conditions. A Ricardo E6 Diesel version engine is converted to run on dual fuel of Diesel and the tested gaseous fuel and is used throughout the work. The engine is fully computerized, and the cylinder pressure data, crank angle data and engine operating ...

Energy Technology Data Exchange (ETDEWEB)

A phenomenological model of turbulent combustion has been developed and validated against data from wide ranging tests on a Ricardo E6 engine. Most tests used iso-octane, with a range of air fuel ratios and ignition timings, for tests at full throttle (with and without knock) and at part throttle. Some full throttle tests were also conducted with methanol and toluene. The engine performance was characterized by mean and coefficient of variation (CoV) of: the peak pressure, the maximum rate of pressure rise, the IMEP, the burn rate and flame speed measurements. The results have been used to argue that the cycle-by-cycle variations in combustion should be characterized by the CoV of IMEP in preference to the CoV of the maximum cylinder pressure. Evidence is also presented to support the observation that the cycle-by-cycle variations in combustion are lower when the early combustion is more rapid. It has ...

Energy Technology Data Exchange (ETDEWEB)

This work proposes an innovative blend of potassium carbonate (K{sub 2}CO{sub 3}) and piperazine (PZ) as a solvent for CO{sub 2} removal from combustion flue gas in an absorber/stripper. The equilibrium partial pressure and the rate of absorption of CO{sub 2} were measured in a wetted-wall column in 0.0 to 6.2 m K{sup +} and 0.6 to 3.6 m PZ at 25 to 110 C. The equilibrium speciation of the solution was determined by {sup 1}H NMR under similar conditions. A rigorous thermodynamic model, based on electrolyte non-random two-liquid (ENRTL) theory, was developed to represent equilibrium behavior. A rate model was developed to describe the absorption rate by integration of eddy diffusivity theory with complex kinetics. Both models were used to explain behavior in terms of equilibrium constants, activity coefficients, and rate constants. The addition of potassium to the amine increases the concentration of CO{sub 3}{sup 2-}/HCO{sub 3}{sup -} in solution. The buffer ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

A facile solution chemistry is demonstrated to fabricate high-quality polycrystalline strontium ruthenium oxide (SrRuO{sub 3}) thin film electrodes on silicon substrates suppressing the formation of undesired ruthenium oxide (RuO{sub 2}) for the deposition of dielectric and ferroelectric materials like lead lanthanum zirconate titanate (PLZT). The robust, highly crystalline SrRuO{sub 3} film fabrication process does not favor the formation of RuO{sub 2} because of molecular level modification of the precursors possessing analogous melting points, yielding homogeneous films. This chemistry is further understood and complemented by kinetic and thermodynamic analysis of the DTA data under nonisothermal conditions, with which the activation energies to form RuO{sub 2} and SrRuO{sub 3} were calculated to be 156 {+-} 17 and 96 {+-} 10 kJ/mol, respectively. The room-temperature resistivity of the SrRuO{sub 3} film was measured to be 850 {+-} 50 {mu}{Omega} cm on silicon ...

Energy Technology Data Exchange (ETDEWEB)

Since a Diesel engine can only be operated always in the condition thinner than the theoretical mixing ratio, a catalytic converter rhodium cannot be used, hence it is impossible to oxidate the portion of incomplete combustion and resolve nitrogen oxides using the catalytic converter rhodium as a spark ignition engine. Also since its combustion is mainly diffusion combustion, the amount of generated soot and fine particles is as much as several times to ten times more than that of a spark ignition engine. Also since no after treatment of exhaust has been established for a Diesel engine, it is necessary to cope with the combustion process which is the source of generating pollutant in order to promote reduction of such pollutant. In this article, awaring of the above, the difficulty of achieving both reduction of fine partiicles and reduction of NO {sub x} at the same time is explained in detail, and ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, the combustible value (i.e. 100-Ash) and combustible recovery of coal flotation concentrate were predicted by regression and artificial neural network based on proximate and group macerals analysis. The regression method shows that the relationships between (a) in (ash), volatile matter and moisture (b) in (ash), in (liptinite), fusinite and vitrinite with combustible value can achieve the correlation coefficients (R{sup 2}) of 0.8 and 0.79, respectively. In addition, the input sets of (c) ash, volatile matter and moisture (d) ash, liptinite and fusinite can predict the combustible recovery with the correlation coefficients of 0.84 and 0.63, respectively. Feed-forward artificial neural network with 6-8-12-11-2-1 arrangement for moisture, ash and volatile matter input set was capable to estimate both combustible value and combustible recovery with ...

Energy Technology Data Exchange (ETDEWEB)

In this article, we review and clarify some of the points made by previous authors regarding chemical looping combustion (CLC). While much of the recent interest in chemical looping combustion has been associated with carbon sequestration, our primary interest here is its potential to increase the thermodynamic efficiency of converting fuel chemical energy into useful work. We expand on several points about the details of CLC that we feel have not previously been sufficiently explored, and suggest alternative (and possibly more practical) approaches that exploit some of the same thermodynamic concepts. We illustrate our key points with {First} and {Second} Law analyses of ideal conceptual processes, which in addition to {CLC} also include isothermal, non-equilibrium, preheated combustion and combustion with thermochemical recuperation. Our results suggest that a significant portion of the potential ...

Energy Technology Data Exchange (ETDEWEB)

The authors experimentally study the separate stages of the determination of iodine in thyroidin by the combustion method in a flask with oxygen. The monotypic, conventional procedures and the procedure of Kolii and Pakhomov were studied. With addition of potassium iodide, a sixfold amount (compared with the initial) of iodine is liberated. Further, the liberated iodine is titrated by sodium thiosulfate. The authors find the degree of influence of a high nitrogen content on the determination of iodine in organic compounds. The procedure developed for the quantitative determination of the iodine in thyroidin by the combustion method is simple, fairly rapid, and can be used for the reliable control of the quality of thyroidin preparations and its starting raw material.

Energy Technology Data Exchange (ETDEWEB)

The aim with this project sponsored by Energimyndigheten is to develop a method for calculations of grate boilers fueled by bark. This report describes this project, 'Evaluation Method for Grate Combustion' (EMGC). CFD codes is an engineering tool applicable in the area of the over-grate section called the furnace. This part of the boiler is easy to model for an experienced CFD code user and the results are usually quite satisfactory for evaluating the combustion process in general. Various gas phases reactions and related combustion processes over the burning bed can be simulated including air staging, fuel staging and SNCR. However the simulation needs information of amount and properties of the burning bed products, entering the furnace. The simulation of the in-furnace processes without this information is often just a numerical speculation. A predictive mathematical model based on physical and ...

Energy Technology Data Exchange (ETDEWEB)

The currently available propellants achieve about 95% of the combustion performance which can be expected theoretically at this time, consequently a technological breakthrough concerning new propellants have been demanded. Among high energy substances which are being studied, polymer azide which can continue combustion without relying on the oxidation reaction is a typical high energy substance to be used for a propellant of the next generation. The composite propellant which has polymer azide as fuel component and ammonium nitrate as oxidizer is considered to be the extremely promising propellant, since it provides no combution product which causes the environmental destruction. (6 figs, 4 refs)

Science.gov (United States)

... Two types of combustible cartridge cases, post impregnated (PI) and beater additive (B/A) are available for the 120 mm tank gun system. ...

International Nuclear Information System (INIS)

... calcium 47 combustion dry ashing high temperature labelled compounds lead

Science.gov (United States)

... Abstract : Small metallic fragments can be trapped in combustible cartridge cases during manufacture and released into the interior-ballistic flow ...

Science.gov (United States)

... ammunition is stored. Combustible cartridge cases could absorb moisture, swell, and not chamber properly. Additionally, moisture ...

Science.gov (United States)

activities, including the combustion of diesel fuel in heavy-duty vehicles and jet fuel in aircrafts. Current details on emissions from the transportation and other...

Science.gov (United States)

... K. E. T,-us, "Clo:ei Chamber Burning Characteristics of Selected Liquid Monopropellants," 14th JANAP Combustion Meeting, CPIA Publication No. ...

Energy Technology Data Exchange (ETDEWEB)

This paper discusses geology, coalfields, coal quality, seams and strata, coal reserves, mining methods, production, coal liquefaction, and research on spontaneous combustion and methane explosions.

Science.gov (United States)

This report provides procedures for evaluating metal, consumable, and combustible cartridge cases. It identifies supporting tests, facilities, and equipment required. Subtests include weapon and ammunition preparation, initial inspection, ammunition chara...

International Nuclear Information System (INIS)

A rapid combustion unit (Baird and Tatlock) incorporating a combustion chamber provided with baffle plates for complete combustion of the sample without the use of a catalyst has been assembled in a glove box for the determination of carbon and hydrogen in actinide complexes. The unit has been modified employing a movable electric furnace and a proportional temperature controller, for decomposition of the sample at desired heating rates. The set-up was standardised employing various reference materials such as benzoic acid, acetanilide, sulphanilamide and 1-chloro 2:4 dinitrobenzene and the standard deviation in the measurements evaluated. It has also been used successfully for the determination of carbon in uranium carbide and carbon and hydrogen in some uranyl-#beta#-diketone-amine N-oxide complexes and in plutonium(IV) oxalate. (auth.).

Science.gov (United States)

Mar 1, 2011... properties to a complex model demanding full combustion kinetics, transport properties, and poppet valve flow characteristics. ...

International Nuclear Information System (INIS)

Single-crystalline cadmium selenide nanoparticles were obtained using high-temperature solution phase synthesis (HTSPS) synthesis. X-Ray powder diffraction and transmission electron microscopy were used to confirm the crystallinity and morphology of the resulting nanoparticles. To study the action of CdSe on antioxidant activity, we selected two biotechnological important strains of microalgae: cyanobacteria Spirulina platensis and red microalgae Porphyridium cruentum. In the case of Porphyridium cruentum, the obtained results demonstrated an increase in the productivity. For Spirulina platensis, the presence of the compound in the cultivating medium decreased the productivity of cyanobacteria.

British Library Electronic Table of Contents (United Kingdom)

Cyst nematodes are troublesome parasites that live on, and destroy, a range of important host vegetable plants. Damage caused by the potato cyst nematode has now been reported in over 50 countries. One approach to eliminating the problem is to stimulate early hatching of the nematodes, but key hatching stimuli are not naturally available in sufficient quantities to do so. Here, we report the first chemical synthesis of solanoeclepin A, the key hatch-stimulating substance for potato cyst nematode. The crucial steps in our synthesis are an intramolecular cyclization reaction for construction of the highly strained tricyclo[5.2.1.01,6]decane skeleton (DEF ring system) and an intramolecular Diels???Alder reaction of a furan derivative for the synthesis of the ABC carbon framework. The present ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

International Nuclear Information System (INIS)

Portuguese 1984. p. 146. Brazil Czepielewski, MA Kater, CE Biglieri, EG Escola

Science.gov (United States)

... MPS) Advanced Liquid Crystalline Optical Materials Superconductivity Computation and Visualization ... Cement-Based Materials Synthesis, Growth, and Analysis of Electronic Materials Photoinduced Charge ...

Wastenet

... Here we will summarize the synthesis, structure activity relationships , and molecular sites of action of mGluR5 PAMs. We will also review preclinical studies ...

Science.gov (United States)

Metastable yttrium-oxide films are synthesized using reactive sputter deposition. The yttrium concentration of the as-deposited film is found to vary as a function of the sputter deposition rate. In addition to the synthesis of the cubic equilibrium phase...

Science.gov (United States)

Hie synthesis of diverse biologically important compounds, under condi- tions which existed on the earth in the initial period of its evolution, ha; ...

UK PubMed Central (United Kingdom)

Objective and sourcesWe reviewed the epidemiologic literature for PFOA.Data synthesisPerfluorooctanoic acid (PFOA) does not occur naturally but is...Full Text Available

Science.gov (United States)

... 4? Program History 5? Center for Advanced Materials and Smart Structures 6? Center for Systems ... Systems 14? Center for Photonic Materials Research 15? Synthesis, Manufacturing and Characterization ...

UK PubMed Central (United Kingdom)

SummaryA microreactor for electrochemical synthesis has been designed and fabricated. It has been shown that different reactions can be carried out successfully using simple protocols.

Energy Technology Data Exchange (ETDEWEB)

The multi-spray direct injection diesel engine has the best efficiency of all combustion systems. The optimization of the air-fuel mixture parameters, especially of the fuel injection, enables the forming of the combustion process in a way, that all requirements and legislative regulations concerning power output, noise and exhaust emissions can be fulfilled. Electronic controlled unit injector systems, as developed by Voest-Alpine Automotive GmbH, Linz, offer the necessary potential to meet the complex requirements.

Energy Technology Data Exchange (ETDEWEB)

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 8 provides a description of instrumentation and controls.

Energy Technology Data Exchange (ETDEWEB)

Fourier transform infrared spectroscopy is a simple, fast, reliable and nondestructive analytical method. By using the method developed in Clark Atlanta University, consistent and reliable infrared spectral results can be obtained. An accurate radiant energy can be calculated from these infrared spectra by using a blackbody as the calibration standards. By means of the specially-designed-and-lab-made sampling inlet and the Horiba gas analyzers, the compositions of CO{sub 2}, CO, UCH, NOx and O{sub 2} etc. from the combustion exhaust gases have been on-line accurately analyzed. The commercial natural gas IR burner performed differently in the different conditions. For the methane-air combustion, at the equivalence ratio {Phi} = 1, the IR burner produced its maximum radiation efficiency, {approximately}31.4%, and the concentration of CO{sub 2} reached its maximum value, {approximately}10.7%. In the fuel-lean region, the O{sub 2} concentration in ...

Energy Technology Data Exchange (ETDEWEB)

In China, the conventional utilization of oil shale is concentrated mainly on oil shale retorting, and burning oil shale in pulverized furnaces, or bubbling fluidized beds. To improve the availability of oil shale, many specialists have advocated burning oil shale in a circulating fluidized bed (CFB), which has a satisfactory combustion efficiency, low NOx and SO{sub 2} emission, adaptability to low-grade coal, etc. In Huadian, China, a plant incorporating three units of 65 th{sup -1} oil shale-fired CFB began successful commercial operation in 1996, proving that burning oil shale in a CFB produces both high combustion efficiency and environmental protection. For effective utilization of oil shale, its pyrolysis and combustion characteristics, emission performance of gaseous pollutants from an oil shale-fired CFB pilot setup, co-combustion characteristics of oil shale and high sulfur coal as well as the ...

Energy Technology Data Exchange (ETDEWEB)

As oil supplies diminish, Britain will have to rely more and more on coal as one of the energy alternatives. To burn coal cleanly and efficiently coal will have to be converted into gas and liquid fuels to replace natural gas and oil. The research and development programme of the National Coal Board is directed towards meeting these new challenges. This paper outlines some of the Coal Board's current projects in the fields of industrial combustion, power generation, domestic combustion, coal gasification and coal liquefaction. 10 figs.

Energy Technology Data Exchange (ETDEWEB)

High pressure experiments in a jet-stirred reactor have been performed to study the NO{sub x} formation in lean premixed combustion of methane/air mixtures. The experimental results are compared with numerical predictions using four well known reaction mechanisms and a model which consists of a series of two perfectly stirred reactors and a plug flow reactor. (author) 2 figs., 7 refs.

Science.gov (United States)

The paper describes the Integrated Air Pollution Control System (IAPCS), a computerized program that can be used to estimate the cost and performance of pre-combustion, in situ, and post-combustion air pollution control configurations in pulverized-coal-fired utility boilers of 1...

Energy Technology Data Exchange (ETDEWEB)

Spark ignition internal combustion engines perform satisfactorily when the fueled with biomass producer gas from a fluidized bed gasifier. Although power output is reduced compared to natural gas levels, full power recovery can be achieved with a relatively low level of supercharging. Important considerations are an adequate fuel delivery system and adquate gas cleaning. ref.

Science.gov (United States)

Studies in advanced coal research are presented. Included are the following: coal science programs; coal preparation and combustion kinetics; advanced technology in liquefaction, including direct and indirect liquefaction; alternative fuels; advanced combustion technology; flue gas cleanup; environmental coordination, technology transfer, and clean coal demonstration program. (CBS)

Energy Technology Data Exchange (ETDEWEB)

The effects of compression ratio on the history of the fuel-burning process was investigated in a single-cylinder direct-injection diesel engine. Two compression ratios of 21.4 and 18.5 were studied by using two wide and shallow bowls. The engine was operated at different speeds and overall air-fuel ratios, but with constant start-of-combustion timing at top dead center. The measured cylinder pressure was used to derive fuel-burning rate. At all conditions, the low-compression-ratio bowl had a larger mass of premixed-burned fuel and a higher peak specific fuel-burning rate. The fuel-burning rate in the diffusion-controlled phase of combustion decreased with decreasing compression ratio. The resulting combustion duration became longer at reduced compression ratio, and the difference could be as large as 14 crank-angle degrees. For the engine conditions examined in this study, the mass of fuel present in the ...

Energy Technology Data Exchange (ETDEWEB)

Fischer-Tropsch (F-T) diesel fuel is characterized by a high cetane number, a near-zero sulphur content and a very low aromatic level. On the basis of the recorded incylinder pressures and injector needle lifts, the combustion characteristics of an unmodified single-cylinder direct-injection diesel engine operating on F-T diesel fuel are analyzed and compared with those of conventional diesel fuel operation. The results show that F-T diesel fuel exhibits a slightly longer injection delay and injection duration, an average of 18.7% shorter ignition delay, and a comparable total combustion duration when compared to those of conventional diesel fuel. Meanwhile, F-T diesel fuel displays an average of 26.8% lower peak value of premixed burning rate and a higher peak value of diffusive burning rate. In addition, the F-T diesel engine has a slightly lower peak combustion pressure, a far lower rate of pressure rise, and a lower ...

Science.gov (United States)

Chemical looping combustion (CLC) is a process in which an oxygen carrier is used for fuel combustion instead of air or pure oxygen as shown in the figure below. The combustion is split into air and fuel reactors where the oxidation of the oxygen carrier and the reduction of the oxidized metal occur respectively. The CLC system provides a sequestration-ready CO2 stream with no additional energy required for separation. This major advantage places combustion looping at the leading edge of a possible shift in strict control of CO2 emissions from power plants. Research in this novel technology has been focused in three distinct areas: techno-economic evaluations, integration of the system into power plant concepts, and experimental development of oxygen carrier metals such as Fe, Ni, Mn, Cu, and Ca. Our recent thorough literature review shows that multiphase fluid dynamics modeling for CLC is not ...

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion (CLC), has previously been studied as a method for separating CO{sub 2} during combustion of gaseous fuels. In this project the possibility to apply this process for direct use of solid fuels has been investigated. The following has been accomplished: A 10 kW reactor system for CLC with solid fuels has been designed and built. Tests with solid fuel and metal oxid particles in a laboratory reactor show that it is possible to oxidize solid fuels with metal oxide particles in cyclic testing, thus giving proof of basic concept. They also show how the reaction rate is affected by temperature, steam concentration etc., and, most important of all, that the rates of reaction are realistic. Tests with metal oxide materials available at low costs have been successful. Chemical-looping combustion with solid fuels has a potential to achieve very low costs for separation of CO{sub 2}, below 10 Euro/ton CO{sub ...

Energy Technology Data Exchange (ETDEWEB)

This study aims to develop a particulate model combining solid waste particle combustion and heavy metal vaporization from burning particles during MSW incineration in a fluidized bed. The original approach for this model combines an asymptotic combustion model for the carbonaceous solid combustion and a shrinking core model to describe the heavy metal vaporization. A parametric study is presented. The global metal vaporization process is strongly influenced by temperature. Internal mass transfer controls the metal vaporization rate at low temperatures. At high temperatures, the chemical reactions associated with particle combustion control the metal vaporization rate. A comparison between the simulation results and experimental data obtained with a laboratory-scale fluid bed incinerator and Cd-spiked particles shows that the heavy metal vaporization is correctly predicted by the model. The predictions ...

Energy Technology Data Exchange (ETDEWEB)

This article describes the utilization of plastic wastes in a blast furnace. The plastic waste is a substitution for petroleum and coal as a raw material for synthesis gas production. The synthesis gas is the reducing agent in the blast furnace for the reduction of iron ores. You can find here an ecological and economical analysis of this process in comparison to the utilization of petroleum and coal. (SR)

International Nuclear Information System (INIS)

The purpose of work is systematical studying of benzo (B) of thiophene-1,1-dioxides and their 2,3-di-hydro derivatives behaviour in the reactions of electrophflic, radical, nucleophilic nitration, reduction of nitro group, embodiment of synthesis of N-amino derivatives, investigation of sulfur containing hetero-cyclic compounds, including of residues of some steroids

Energy Technology Data Exchange (ETDEWEB)

The synthesis of (/sup 14/C)-10,11-Epoxy-(2E,6E)-farnesyl diazoacetate in one vessel, starting from (/sup 14/C)-glyoxylic acid, is described. This compound is useful as a potential photoaffinity labeling agent for juvenile hormone binding sites.

International Nuclear Information System (INIS)

We recently found that injection of 2 mCi of yttrium 90 (90Y; approximately 23,000 rads) into normal canine knees stimulated glycosaminoglycan (GAG) synthesis by femoral condylar cartilage. The present investigation was conducted to determine whether radiation affects cartilage metabolism directly. Rates of GAG synthesis and degradation in normal canine articular cartilage were studied following irradiation. Cultured synovium from the same knees was treated similarly, to determine the effects of irradiation on hyaluronic acid synthesis. Twenty-four hours after exposure to 1,000 rads, 10,000 rads, or 50,000 rads, 35S-GAG synthesis by the cartilage was 93%, 69%, and 37%, respectively, of that in control, nonirradiated cartilage. The effect was not rapidly reversible: 120 hours after exposure to 50,000 rads, GAG synthesis remained at only 28% of the control level. Autoradiography ...

Energy Technology Data Exchange (ETDEWEB)

Stable strange quark matter produced in the QCD phase transition in the early universe will trap neutrons and repel protons, thus reducing primordial helium production, Ysub(p). For reasonable values of Ysub(p), the radius of strange droplets must exceed 10/sup 6/ cm if strange matter shall solve the dark-matter problem without spoiling Big Bang helium synthesis. (orig.).

UK PubMed Central (United Kingdom)

The rates of synthesis of a class of both secreted and intracellular degradative enzymes in Bacillus subtilis are controlled by a signal transduction pathway defined by at least four regulatory genes:...Full Text Available

UK PubMed Central (United Kingdom)