Energy Technology Data Exchange (ETDEWEB)

It was to be investigated why inexplicable cracking occurred in plain stainless austenitic steel pipes of heat exchangers in discrete sites of the inner surface exposed to acid even with anodic corrosion protection, and what countermeasures must be taken. The following materials were investigated: X 6 CrNiTi 18 10 and X 6 CrNiMoTi 17 12 2. The influence of mechanical vibrations on passive film formation and destruction was investigated in unconstrained pipes and pipes constrained at one end in conditions of anodic protection at frequencies of 0 to 160 Hz and temperatures of 98 to 130 degrees Centigrade in 98% sulphuric acid. The authors were unable to reconstruct the cracks observed in practical operation in anodically protected heat exchanger pipes of stainless austenitic steel. (orig./MM). 5 refs., 2 tabs., 71 figs.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... Accession Number : ADD141533. Title : Yttrium Oxides in Vacuum-Plasma- Sprayed CoNiCrAlY Coatings,. Descriptive Note : Journal Article,. ...

Energy Technology Data Exchange (ETDEWEB)

A series of stainless austenitic and ferritic materials was exposed for 100 days to boiling nitric acid which contained no corrosion products; the corrosion rates and depths of the grain boundary attack were observed. - Provided the structure is precipitation-free, the following are suitable for long-term exposure; the austenitic steels X 2 CrNi 19 11, X 1 CrNi 25 21, X 1 CrNiMoN 25 22 2 and X 1 NiCrMoCu 31 27 4, the practically Mo-free and Cu-free development steel X 1 NiCr 31 27, and the highly Mo-alloyed variant X 1 NiCrMoCu 31 27 5. - In the case of alloy NiCr21Mo it is advisable to limit the concentration and/or temperature of the nitric acid. - The 'superferrite' X 1 CrNiMoNb 28 4 2, the Japanese steel X 1 CrNiNb 30 2 and the austenitic steels X 2 CrNiMoN ...

International Nuclear Information System (INIS)

The results of x-ray diffraction, dc magnetization, and 61Ni Moessbauer spectroscopy studies of the ternary arsenide CrNiAs are reported. This compound crystallizes in the orthorhombic Fe2P-type structure (space group P6-bar2m) with the lattice parameters a 6.1128(2) A and c = 3.6585(1) A. CrNiAs is a mean-field ferromagnet with Curie temperature TC = 171.9(1) K and the critical exponents ? 0.514(18), ? = 1.010(16), and ? = 2.922(10). The temperature dependence of the magnetic susceptibility above TC follows the modified Curie-Weiss law with a paramagnetic Curie temperature of 176.0(3) K and effective magnetic moment per transition metal atom of 2.42(1) ?B. The magnetic moment per formula unit at 4.2 K is found to be 1.114(33) ?B. The hyperfine magnetic field at 61Ni nuclei at 4.2 K of 41.5(1.0) kOe implies that the Ni atoms carry a magnetic moment of 0.15(3) ?B, and that the moment ...

Energy Technology Data Exchange (ETDEWEB)

Nitridation of Cr-bearing alloys can yield low interfacial contact resistance (ICR), electrically- conductive and corrosion-resistant CrN or Cr2N base surfaces of interest for a range of electrochemical devices, including fuel cells, batteries, and sensors. This paper presents results of exploratory studies of the nitridation of two high Cr (30-35 wt%) commercially available Ni-Cr alloys and a ferritic high Cr (29 wt.%) stainless steel for proton exchange membrane fuel cell (PEMFC) bipolar plates. A high degree of corrosion resistance in sulfuric acid solutions designed to simulate bipolar plate conditions and low ICR values were achieved via nitridation. Oxygen impurities in the nitriding environment were observed to play a significant role in the nitrided surface structures that formed, with detrimental effects for the Ni-Cr base alloys, ...

Energy Technology Data Exchange (ETDEWEB)

The austenitic nitrided Cr-Mn steels CrMnN 1812, CrMnNMo 1714 and CrNiTi 1810 has been investigated in chloride nitric acid at temperature 20-60 C. The Potentials of pitting nucleation and the time for pitting initiation has been determinate by the hronoamperometric method. It was established that alloying only with nitrogen is not sufficient procedure for obtaining of resistive to localised corrosion steel structure. Of importance for the resistance to localised corrosion of Cr-Mn steels is alloying with molybdenum. (orig.) [Deutsch] Die austenitischen stickstoffhaltigen Cr-Mn Staehle CrMnN 1812, CrMnNMo 1714 und der klassische CrNiTi 1810 wurden in chloridhaltigen Salpetersaeureloesungen im Temperaturbereich 20-60 C untersucht. Durch die hronoamperometrische Methode wurden die Potentiale der ...

Energy Technology Data Exchange (ETDEWEB)

Surface analytical studies of high nitrogen austenitic stainless steels exposed to deaerated 0.1M HCl have revealed that nitrogen alloying additions influence the composition of salt layers and the passive film/alloy interface. In this study the authors employ electrochemical techniques and variable angle X-ray Photoelectron Spectroscopy (XPS) to examine the passive films formed on a series of austenitic stainless steels, Fe18Cr8Ni, Fe18Cr8Ni0.2N, Fe20Cr20Ni, Fe20Cr20Ni6Mo and Fe20Cr20Ni6Mo0.2N, in acidic chloride aqueous solution. In addition, several other model alloys, Fe19Cr, Fe19Cr9Ni, Fe19Cr2.5Mo, and Fe19Cr9Ni2.5Mo, were examined before and after ...

Energy Technology Data Exchange (ETDEWEB)

The geometrical and chemical effects of cerium (Ce) addition to Ni-Cr anode electrode in molten carbonate fuel cells (MCFCs) were investigated by measuring the fractal dimensions and wettability of four types of anode electrode with Ce added up to 5 wt.%. In addition, their cell performances were investigated through a single cell operation test and their results were explained based on the wettability of the anode electrodes. The addition of Ce to the anode electrode increased the fractal dimensions and wettabilities of the electrodes. Despite the even larger electrical resistivity of Ce compared to that of Ni and Cr, the electrical resistances of the Ce-added anode electrodes were slightly increased with increasing level of Ce addition. This might be ascribed to the greater wettability of the Ce-added anode electrode that enhanced the cell performance. Therefore, the greater wettability of the Ce-added anode electrode ...

Energy Technology Data Exchange (ETDEWEB)

The study of passive films formed on a nickel base alloy type Inconel 600 is performed by capacitance measurements (Mott-Schottky approach). This research is supported by the passivation study of the alloying elements Ni, Cr, Fe and high purity alloys Ni-Cr, Ni-Fe, Ni-Cr-Fe. The results obtained show that the capacitive behaviour of the Inconel 600 in the passive state is similar to that on a p-n heterojunction to which a barrier zone of nickel oxide is added. The individual or combined action of alloying elements on the development of this kind of electronic structure is discussed. (authors). 5 refs., 6 figs.

International Nuclear Information System (INIS)

Microstructure characterization is important for controlling the quality of laser welding. In the present work, a detailed microstructure characterization by transmission electron microscopy was carried out on the laser welding cast Ni-based superalloy K418 turbo disk and alloy steel 42CrMo shaft and an unambiguous identification of phases in the weldment was accomplished. It was found that there are #gamma#-FeCrNiC austenite solid solution dendrites as the matrix, (Nb, Ti) C type MC carbides, fine and dispersed Ni_3 Al #gamma#' phase as well as Laves particles in the interdendritic region of the seam zone. A brief discussion was given for their existence based on both kinetic and thermodynamic principles.

International Nuclear Information System (INIS)

Inert markers (evaporated tungsten and silver) were used in growth studies of silicides formed both by thermal annealing and by ion mixing in the Ni/Si, Pd/Si, and Cr/Si systems. The markers were initially imbedded inside silicides and backscattering spectrometry was used to determine the marker displacement after different processing conditions. The results obtained in thermal annealing are quite consistent with that found in previous investigations. Ni is the dominant diffusing species in Ni_2Si, while Si is the diffusing species in CrSi_2. In Pd_2Si, both Pd and Si are moving species with Pd the faster of the two. In contrast, in growth of silicides by ion irradiation Si is the faster diffusing species in all three systems.

British Library Electronic Table of Contents (United Kingdom)

Gas nitridation has shown excellent promise to form dense, electrically conductive and corrosion-resistant Cr-nitride surface layers on Ni-Cr base alloys for use as proton exchange membrane fuel cell (PEMFC) bipolar plates. Due to the high cost of nickel, Fe-base bipolar plate alloys are needed to meet the cost targets for many PEMFC applications. Unfortunately, nitridation of Fe-base stainless steel alloys typically leads to internal Cr-nitride precipitation rather than the desired protective surface nitride layer formation, due to the high permeability of nitrogen in these alloys. This paper reports the finding that it is possible to form a continuous, protective Cr-nitride (CrN and Cr2N) surface layer through nitridation of Fe-base stainless steel alloys. The key to form a protective Cr...

Energy Technology Data Exchange (ETDEWEB)

It has been clarified by the present authors, based on the plasma nitriding of Fe-Cr alloys and Fe-Ti alloys carried out at the temperature under 550{degree}C hitherto, that an internal nitriding layer is formed due to the fine dispersion of the particles of Cr nitride and Ti nitride in {gamma}{prime} Fe4N layer on the specimen surface. In this study, the plasma nitriding of Fe-Cr alloys are carried out at 650{degree}C, and the effects of the solute (Cr) content on the structures, nitride and the thickness distribution are examined. The main results obtained therefrom are indicated hereafter. In accordance with the observation on the cross-sectional structure of the alloys, only the nitriding layer deduced as the dispersion and precipitation of the particles of Cr nitride from {alpha}-Fe of the mother phase is formed, while {gamma}{prime}-Fe4N layer, which is found at the ...

Energy Technology Data Exchange (ETDEWEB)

The oxidation of Cr(III) hydroxides, mixed Fe(III)-Cr(III) hydroxides, and specimens of spinel phases NiCr2O4 and Fe(Cr,Fe)2O4 have been investigated in alkaline suspensions under the action of air and pure oxygen (1-3 atm). The rate of reaction increases with increasing alkali concentration, temperature, and oxygen pressure. Pu(IV) fixed on chromium hydroxides is not oxidized by oxygen under these conditions but is retained in the precipitate.

Energy Technology Data Exchange (ETDEWEB)

For evaporation crystallization of extremely corrosive FGD scrubber solutions which - depending on the process - can lead all the way to a product suitable for depositing, an economic equipment concept based on metallic construction materials was to be investigated. In a parameter study, electrochemical test methods were used to determine the influence of the pH value, the Fe{sup 3+}, F and So{sub 2} contents in a solution containing 200 g/l CaCl{sub 2}+30 g/l NaCl at 80deg C on the resistance to pitting corrosion of stainless steels and NiCrMo alloys. In addition, electrochemical and wet corrosion tests (e.g. crevice corrosion) were conducted using original FGD scrubber solutions with 43-50% dry substance from the power plants Reuter-West, Oberhavel and Rudow of the BEWAG, Berlin. The results were compared to those of standardized and non-standardized short-term tests for determining the critical pitting corrosion and crevice corrosion temperatures for the various ...

British Library Electronic Table of Contents (United Kingdom)

Statement of problem Titanium is the most biocompatible metal used for dental casting; however, there is concern about its marginal accuracy after porcelain application since this aspect has direct influence on marginal fit. Purpose The purpose of this study was to determine the effect that metal selection and the porcelain firing procedure have on the marginal accuracy of metal ceramic prostheses. Material and methods Cast CP Ti, milled CP Ti, cast Ti-6Al-7Nb, and cast Ni-Cr copings (n=5) were fired with compatible porcelains (Triceram for titanium-based metals and VITA VMK 95 for Ni-Cr alloy). The Ni-Cr alloy fired with its porcelain served as the control. Photographs of metal copings placed on a master die were made. Marginal discrepancy was determined on the photographs using an image ...

Energy Technology Data Exchange (ETDEWEB)

Single crystals of trigonal Cr{sub 2}Te{sub 3}, monoclinic Cr{sub 5}Te{sub 8}, and trigonal Cr{sub 5}Te{sub 8} were prepared and the single crystal structures were determined. The structures are related to the NiAs structure type by successive removal of Cr in every second metal atom layer parallel to the c axis. The strong relationship between the structures is evidenced by their very similar X-ray powder patterns. In trigonal Cr{sub 2}Te{sub 3} excess Cr occupies only one of the two possible sites. In monoclinic Cr{sub 5}Te{sub 8} the Cr atoms occupy four different crystallographic sites. The resulting ordering of the vacancies is significantly different from the hitherto reported crystal structures of transition metal chalcogenides M{sub 5}X{sub 8}. A slight increase of the tellurium content leads ...

Energy Technology Data Exchange (ETDEWEB)

Stress corrosion cracking tests in constant extension rate tensile (CERT) and constant load tensile (CLT) tests were conducted on Ni-xCr- 9Fe-yC in Ar, water, and a LiOH-boric acid solution. Cr and C improve the resistance of Ni-base alloys to IG cracking in both Ar and water at 360C. Since creep plays a role in IG cracking, one possible explanation for the role of the environment involves its effect on the creep. Experiments were conducted on the role of C in the deformation behavior and failure mode of Ni-16Cr-9Fe. Constant load experiments were conducted on Ni-16Cr-9Fe to determine if the CLT test is more aggressive than CERT. The electron backscattering technique in a SEM is being developed in order to extend the IG cracking studies to grain sizes typical of commercial alloys, 20-30 microns.

International Nuclear Information System (INIS)

Results of hot cracking on welds with compositions between alloy 800 and AWS ER NiCr 3. Investigation of the influence of Si, Mn, Ti and Al on the hot cracking suscpetibility of the alloy 800. (orig.).

International Nuclear Information System (INIS)

Localized deformation may play a key role in the underlying mechanism of irradiation assisted stress corrosion cracking (IASCC) in light water reactor core components. In this study, four austenitic alloys, 18Cr8Ni, 15Cr12Ni, 13Cr15Ni and 21Cr32Ni, with different stacking fault energies were irradiated to 1 and 5 dpa at 360 deg. C using 3.2 MeV protons. Interrupted constant extension rate tensile (CERT) tests were conducted in a simulated BWR environment to determine IASCC susceptibility. In order to characterize the localized deformation in slip channels and grain boundaries, parallel CERT experiments were also performed in an argon atmosphere. Results show that the IASCC susceptibility of the tested alloys increases with increasing irradiation dose and decreasing stacking fault energy. IASCC tends to initiate at ...

International Nuclear Information System (INIS)

Three ternary austenitic alloys (Fe-15Cr-25Ni, Fe-15Cr-25Ni-0.04P, Fe-15Cr-45Ni in both annealed and cold worked conditions) were irradiated at 465 C to 0.15, 0.28, and 0.42 dpa at above core position in the Fast Flux Test Facility utilizing the Materials Open Test Assembly to study the separate and synergistic effects of He/dpa ratio, phosphorus addition, nickel content and cold work level on microstructural evolution and hardening. The helium/dpa ratio was varied by isotopic doping with "5"9Ni to enhance the production rate of helium. The helium production rate was evaluated to be 62 appm He/dpa in the "5"9Ni-doped specimens and 0.26 appm He/dpa in the undoped specimens. Transmission electron microscopic examinations revealed that alloy composition affected significantly the evolution of microstructure during ...

Energy Technology Data Exchange (ETDEWEB)

To clarify the mechanism of plasma nitriding, the authors examined the optical microstructure, the hardness, the precipitation, and the concentration of dissolved nitrogen in Fe-18Cr-9Ni nitrided using plasma in the range of 723-823 K. Compared with ammonia-gas nitriding, the features of plasma nitriding are the formation of small chromium-nitride precipitates (CrN), the absence of an externally nitrided layer, the high concentration of dissolved nitrogen, and the high hardness (HV = 1,200). The diffusion coefficient of nitrogen in the present alloy was determined using the growth rate of the internally nitrided layer, based on calculations used in internal oxidation. Plasma- and gas-nitriding were also compared with respect to the growth rate of the nitrided layer.

Energy Technology Data Exchange (ETDEWEB)

The effect of the composition of multicomponent Zr-Ti-V-Mn-Cr-Ni alloys on their hydrogen-storage capacity and on the rate of electrosorption/desorption hydrogen was investigated under potentiodynamics as well as single-pulse and long-term galvanostatic conditions. The main characteristics of alloys and alloy electrodes were determined by their structural analysis by means of X-ray diffraction and scanning electron microscope, by specific surface area test and by determination of the hydrogen absorption/desorption isotherms in the gas/solid phase system. It was found that only the alloys with a manganese content below a threshold could be used as electrode materials for Ni-MH batteries, whereas the modification of the electrode material by micro-encapsulation of alloy particles should limit the dissolution of manganese from the electrode material in a strong alkaline solution. (orig.)

British Library Electronic Table of Contents (United Kingdom)

The alloying effects on K to L shell vacancy transfer probabilities (?KL) in 3d transition metals have been carried out by X-ray fluorescence studies of various alloy compositions. K X-ray intensity ratios of Ti, Cr, Fe, Co, Ni, and Cu elements in the FexNi1?x, FexCr1?x, NixCr1?x, FexCryNi1?(x+y), TixNi1?x, TixCo1?x, and CoxCu1?x alloys have been measured following excitation by 22.69keV X-rays from a 10 mCi 109Cd radioactive point source and ?KL values for alloying elements have been determined from these ratios. The spectrum of characteristic K-X-ray photons from samples were detected with a high resolution Si(Li) detector coupled to a 4 K multichannel analyzer. The present investigation makes it possible to ...

Energy Technology Data Exchange (ETDEWEB)

Flow-curve characteristics of the heat-resistant steels X 20 CrMoV 12.1 and alloy 800 (X5NiCrTiAl32.20) were measured by tensile and compression tests at temperatures between room temperature and 800 C and strain rates {epsilon}{<=}10 s{sup -1} in connection with microstructure investigations (dislocation content, carbide precipitation) by TEM and X-ray diffraction analysis (XDA). Modelling the deformation behaviour of the steels in terms of the microstructure development indicates that it cannot be explained in a simple manner. The flow curves {sigma}={sigma}({epsilon}, {epsilon}, T) lie, in general, between those predicted by the Kocks-Mecking-Estrin model and a modified (i.e. two-parameter) Roberts model. Because of the less complicated nature of the deformation process the correspondence of experiment and modelling is more satisfying in the case of the material X 20 CrMoV 12.1. (orig.) 26 refs.

Energy Technology Data Exchange (ETDEWEB)

In order to investigate the role of amorphous SiO{sub 2} particles in corrosion and wear resistance of Ni-based metal matrix composite alloying layer, the amorphous nano-SiO{sub 2} particles reinforced Ni-based composite alloying layer has been prepared by double glow plasma alloying on AISI 316L stainless steel surface, where Ni/amorphous nano-SiO{sub 2} was firstly predeposited by brush plating. The composition and microstructure of the nano-SiO{sub 2} particles reinforced Ni-based composite alloying layer were analyzed by using SEM, TEM and XRD. The results indicated that the composite alloying layer consisted of {gamma}-phase and amorphous nano-SiO{sub 2} particles, and under alloying temperature (1000 deg. C) condition, the nano-SiO{sub 2} particles were uniformly distributed in the alloying layer and still kept the amorphous structure. The corrosion resistance of composite alloying layer was ...

International Nuclear Information System (INIS)

Daily intakes of certain trace elements (Pb, Cd, Ni, Hg, and Cr) were assessed using dietary history and weighed record methods and concurrent chemical analysis (CA) of duplicate portions, along with blood levels, in a group (21 M, 23 F) of inhabitants of the Gubbio area (Belvedere, Biscina Scritto). The evaluation of only intake of trace elements was accomplished in 40 subjects (20 M, 20 F) 1 year later. In both surveys, trace element intakes were generally lower than the potential tolerable weekly intake. However, daily intakes of Pb, Cd, Ni, Hg, and Cr were higher in men compared to women in both surveys (P<0.05). In fact, intakes at the 50th percentile were greater in men by approximately 75% for Pb, 91% for Cd, 20% for Ni, 45% fo Hg, and 29% for Cr in the first survey. In the second survey, percentage differences for Pb, Cd, Ni, and ...

Energy Technology Data Exchange (ETDEWEB)

Gas nitridation has shown excellent promise to form dense, electrically conductive and corrosion-resistant Cr-nitride surface layers on Ni-Cr base alloys for use as proton exchange membrane fuel cell (PEMFC) bipolar plates. Due to the high cost of nickel, Fe-base bipolar plate alloys are needed to meet the cost targets for many PEMFC applications. Unfortunately, nitridation of Fe-base stainless steel alloys typically leads to internal Cr-nitride precipitation rather than the desired protective surface nitride layer formation, due to the high permeability of nitrogen in these alloys. This paper reports the finding that it is possible to form a continuous, protective Cr-nitride (CrN and Cr{sub 2}N) surface layer through nitridation of Fe-base stainless steel alloys. The key to form a protective Cr-nitride surface layer was found to be the ...

Energy Technology Data Exchange (ETDEWEB)

Weight loss measurements were performed in 20% and 28% hydrochloric acid at 90/sup 0/C on carbon steel, 22Cr5Ni duplex stainless steel, and two superaustenitic steels - 27Cr31Ni3Mo and 19Cr25Ni4Mo -, in presence of organic substances used singly or mixed. The organic substances examined were quaternary ammonium salts (1-4-pyridyl)-pyridinium chloride hydrochloride, dodecylpyridiniumchloride, benzyldimethylstearylammonium chloride, and dodecyltrimethylammonium bromide), alkynols (1-octyn-3-ol, propargyl alcohol) and trans-cinnamaldehyde. The synergistic effect of potassium iodide on the inhibitive efficiency of the organic substances was studied. The variations of corrosion rate during the test time (normally six hours) were recorded by means of polarization resistance measurements. Polarization curves were also recorded. The results showed that the corrosion ...

Energy Technology Data Exchange (ETDEWEB)

Computerized descriptions of isothermal, multi-stage creep fatigue load were established for one melt each of steels of the type 1%CrMoNiV and 12%CrMoV and were implemented in the service life prediction program SARA 2. SARA 2 predicts the time and number of cycles to incipient cracking for a given number of part cycles on the basis of rules for description of cyclic deformation and damage and of a generalized damage accumulation hypothesis. [German] Fuer je eine Schmelze der Staehle vom Typ 1%CrMoNiV and 12%CrMoV wurde eine rechnergestuetzte Beschreibung fuer isotherme mehrstufige Kriechermuedungsbeanspruchung erstellt und in ein Lebensdauerzaehlerprogramm SARA 2 implementiert. Auf der Grundlage von Regeln zur Beschreibung von zyklischer Verformung und Schaedigung unter Anwendung der verallgemeinerten Schadensakkumulationshypothese ermittelt SARA 2 fuer beliebig vorgebbare Teilzyklen einen ...

Energy Technology Data Exchange (ETDEWEB)

Papers are presented on the development of oxidation- and sulfidation-resistant ferritic alloys; the microstructural stability of sulfidation-resistant FeCrAl stainless steels around 500 C; age hardening in Fe-Mn-Al-C austenitic alloys; the oxidation/corrosion behavior of low-Cr Fe-Cr-Ni alloys containing Zr or Nb; the high temperature oxidation/corrosion of iron-based superalloys; and the role of Mo in the Na/sub 2/SO/sub 4/ induced corrosion of superalloys at high temperature. Topics discussed include the effect of variations of Co content on the cyclic oxidation resistance of selected Ni-base superalloys; high temperature oxidation of Fe based alloys; the morphological development of high temperature oxide scales of Fe-Mn-Al base alloys; and the oxidation of an Fe-Mn-Al-C alloy at 1000 C. Consideration is given to the corrosion properties of Fe-Mn-Al alloys; passive films formed on nonmagnetic ...

Energy Technology Data Exchange (ETDEWEB)

The procedure for field corrosion tests in sea water is decribed in DIN 50 917, Part II. Distinction is made thereby between long-term undisturbed test specimens, which remain at the exposure site up to the time of sampling, and disturbed test specimens, which are cleaned at certain time intervals for intermediate examination and subsequently exposed again. The comparability of results obtained with the two different types of test was to be investigated at the Helgoland test installation. At an exposure period of up to four years, undisturbed specimens of unalloyed and low-alloy steel grades feature considerably lower corrosion losses than disturbed specimens. At a longer exposure period of up to seven years, the corrosion rate can increase substantially again with the exposure time. This can be attributed to sulphate reduction in the anaerobic zone under the top coating. An effect of the alloying elements is also possible. With good and adequately thick coating systems, no difference ...

International Nuclear Information System (INIS)

We reported in previous papers that both the near-uv and the visible photosensitivities of ferroelectric-phase PLZT (lead lanthanum zirconate titanate) ceramics are increased by as much as four orders of magnitude by ion implantation or a combination of thermal diffusion of Al and ion implantation. New results are presented here on high-energy (1 MeV) implants of Al and Ni and coimplants of Al + Ne and Ni + Ne, and these results are compared with earlier 500 keV implants of Al and Cr and coimplants of Al + Ne and Cr + Ne as surface modification techniques for increasing the visible photosensitivity of PLZT. The important role of grain size in determining optimum contrast and resolution of stored optical information is described in terms of new experimental results.

Energy Technology Data Exchange (ETDEWEB)

The phase transformations and properties of a precipitation-hardened Ni-Cr-based alloy are investigated as a function of C, B, Nb, and Cr contents. It is found that the primary role of Nb consists in the formation of an independent phase, delta-Ni3Nb, a part of a gamma/gamma-prime-delta eutectoid (for high C and B concentrations) and in stimulating the gamma-sigma reaction consecutively with the gamma double prime-delta reaction (for low C and B concentrations). In both cases, the long-term strength characteristics of the Nb-alloyed system are relatively low. The substitution of boron for carbon contributes to a reduction in the number of nucleation sites for topologically close-packed phases and to the formation of more stable (with respect to excess compounds) M3B2 and MB2 borides. The high-boron material exhibits better properties and phase stability under mechanical and thermal loading. 13 references.

International Nuclear Information System (INIS)

The possible corrosion damage is discussed of the CrNi and CrNiMo types steels used as structural materials in WWER type nuclear power plants. It includes point and slot corrosion, corrosion cracking and corrosion fatigue as well as corrosion denting. Also discussed are test procedures that simulate operating conditions and are used for assessing the properties of metallurgical products (sheets and tubes) used in nuclear power engineering. Briefly described is a system for testing the said products in an aqueous medium while keeping the test parameters in a narrow range for a long time. Under the defined temperature, pressure and corrosion medium composition, the test specimens in this system can mechanically be loaded, both statically and dynamically or a temperature gradient can be produced at the tube-tube plate joint. (Z.M.). 1 fig., 1 tab., 10 refs.

Energy Technology Data Exchange (ETDEWEB)

Ba, Cd, Cr, Cu, Fe, Ni, Pb and Zn were determined in birch leaves (Folium Betulae), dandelion roots (Radix Taraxacae), hawthorn blossom (Inflorescentia Crataegi) and their infusions by graphite furnace atomic absorption spectrometry (GFAAS) after microwave digestion of plant samples. Infusions were made from herbs according to prescription for patients, provided by the producer of medicine on the package. The results obtained were compared with daily requirements for each element. Results show high content of cadmium in the medicinal plants analyzed. The highest level in infusions was observed for Ni and Zn (over 90% of the total element concentration for Ni and in most cases over 50% for Zn), and the lowest for Cd and Pb. The calculated daily intake of majority of the analyzed elements was very low (under 1% of daily requirements)

UK PubMed Central (United Kingdom)

Bacterial plasmids contain specific genes for resistances to toxic heavy metal ions including Ag+, AsO2-, AsO4(3-), Cd2+, Co2+, CrO4(2-), Cu2+, Hg2+, Ni2+, Pb2+, Sb3+, and Zn2+. Recent progress with...Full Text Available

International Nuclear Information System (INIS)

Radionuclide x-ray fluorescence method was used in the determination of Cr, Ni and other heavy metals content in wastewater of an engineering plant taken both before and after chemical treatment. Toxic effects of the wastewaters using Allium cepa root tip cells were tested. (author) 8 refs.; 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

Carbide reactions occurring in a precipitation-hardening gamma/gamma-prime Ni-Cr alloy during prolonged high-temperature aging are investigated experimentally. It is found that the decomposition of primary MC carbides, which is accompanied by the precipitation of M23C6 particles, may lead to void nucleation and growth. The effect of carbide transformations on the residual properties of the material at temperatures above the equicohesion temperature is observed at the late stages of aging only. 6 references.

International Nuclear Information System (INIS)

Basic studies of the oxidation resistance of Fe-Cr binary and Fe-Cr-Ni ternary alloys in pure oxygen have shown that the excellent corrosion resistance of Alloy 800 is explicable in terms of the low defect concentrations and diffusion rates in the oxide forming on alloys of this composition in sufficiently oxidising environments. The performance of Alloy 800 in environments of particular importance to nuclear power generation is briefly reviewed to determine to what extent ideas derived from the basic studies of Fe-Cr-Ni ternary alloys are borne out in practice. The good corrosion resistance of Alloy 800 in steam and CO_2 and, to some extent, in molten salt environments is in agreement with the behaviour of ternary alloys in oxygen. Minor aliovalent alloying additions are only expected to have a significant effect on the oxidation resistance of Alloy 800 if they favour the formation of breakthrough duplex oxidation. In ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this work was to investigate the role of chromium on hydrogen embrittlement of Ni-Cr-Fe alloys and thus to develop a better understanding of the low-temperature stress corrosion cracking (SCC) phenomenon. The effect of chromium on hydrogen embrittlement was examined using tensile tests followed by material evaluation via scanning electron microscopy (SEM) and light optical microscopy. Four alloys were prepared with chromium contents ranging from 6 to 35 wt pct. In the uncharged condition, ductility, as measured by the percent elongation or reduction in area, increased as the alloy chromium content increased. Hydrogen appeared to have only minor effects on the mechanical properties of the low-chromium alloys. The addition of hydrogen had a marked effect on the ductility of the higher-chromium alloys. In the 26 pct chromium alloy, the elongation to failure was reduced from 53 to 14 pct, with a change in fracture mode from mixed ductile dimple and ...

International Nuclear Information System (INIS)

An analysis of the passive films formed on amorphous alloys of the system Fe-10% Cr-5% Mo-P-metalloid and Fe-10% Cr-5% Mo-B-Si revealed that they are more markedly enriched with chromium in silicon-free alloys. In silicon-containing amorphous alloys the passive films were highly enriched with silicon, which occurred in these films in the form of a corrosion product close to SiO_2. As shown by the investigations of a study of the anodic behavior of Fe_4_0Ni_4_0P_1_4B_6 and Fe_4_0Ni_3_8Mo_4B_1_8, phosphorus facilitates the passivation of amorphous alloys by reducing the solution current in the active state and enriching the surface layers of the metal in the form of a black prepassivation film which also contains nickel and iron. The behavior of Fe-Ni amorphous alloys containing only boron as metalloid additive differs little from that of crystalline alloys of similar composition but ...

Energy Technology Data Exchange (ETDEWEB)

Time-temperature-precipitation diagrams have been established for two steels with 6% Mo, 21% Cr, 25% Ni, 0.14 and 0.19% N (Cronifer 1925 h Mo = 1.4529, UNS N 08925) and for one steel with 6% Mo, 20% Cr, 18% Ni and 0.21% N (UNS S 31 254). The corresponding time-temperature-sensitization diagrams (in accordance to SEP 1877/II) and time-temperature-pitting diagrams (testing in 6% FeCl{sub 3} solution) have been evaluated as well. Precipitation of intermetallics occurs rapidly especially in the range between 700 and 1000{sup 0}C. In case of the 18% Ni steel and the 25% Ni/0.14% N steel grain boundaries are covered to a large extent with precipitates after only 15 min at 850 or 950{sup 0}C. In case of the 25% Ni/0.19% N steel precipitation is considerably slower. Therefore, when welding according to established rules and recommendations, no ...

International Nuclear Information System (INIS)

The effect of severe plastic deformation by cold high pressure torsion (HPT) on radio frequency (RF) plasma nitriding of pure iron, as well as St2K50 and X5CrNi1810 steels was investigated. Nitriding was carried out for 3 h in a nitrogen atmosphere at a pressure of 10"-"5 bar and temperatures of 350 and 400 deg. C. Nitrided specimens were analysed by scanning electron microscopy (SEM), X-ray diffraction and micro hardness measurements. It was found that HPT enhances the effect of nitriding leading almost to doubling of the thickness of the nitrided layer for pure iron and the high alloyed steel. The largest increase in hardness was observed when HPT was combined with RF plasma nitriding at 350 deg. C. In the case of pure iron, the X-ray diffraction spectra showed the formation of #epsilon# and #gamma#' nitrides in the compound layer, with a preferential formation of #gamma#' at the expense of the #alpha#-phase at the higher nitriding temperature. The corresponding ...

International Nuclear Information System (INIS)

Exploratory experiments of laser welding cast Ni-based superalloy K418 turbo disk and alloy steel 42CrMo shaft were conducted. Microstructure of the welded seam was characterized by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy-dispersive spectrometer (EDS). Mechanical properties of the welded seam were evaluated by microhardness and tensile strength testing. The corresponding mechanisms were discussed in detail. Results showed that the laser-welded seam had non-equilibrium solidified microstructures consisting of FeCr_0_._2_9Ni_0_._1_6C_0_._0_6 austenite solid solution dendrites as the dominant and some fine and dispersed Ni_3Al #gamma#' phase and Laves particles as well as little amount of MC short stick or particle-like carbides distributed in the interdendritic regions. The average microhardness of the welded seam was relatively ...

International Nuclear Information System (INIS)

The compositions of passive films formed on Fe-17Fr-13Ni (at. %) and Fe-18.5Cr-14Ni-1.5Mo (100) single crystals have been determined and the structure of the alloy under the film has been investigated. The alloys were passivated in 0.05M H_2SO_4 at 250 mV/SHE for 30 min. The oxygen content was measured by nuclear microanalysis using the "1"6O(d,p) "1"7O* reaction. The oxygen content in the passive film is similar for the two alloys and equal to (12#+-#2) 10"1"5 O/cm"2. The cationic compositions of the passive films have been determined by "4He channeling at two incident beam energies: 0.8 and 2.0 MeV. For the two alloys studied, a total cation content of (5#+-#2)10"1"5 at/cm"2 is found in the passive films. The corresponding thickness is about 12 A. There is an excess of oxygen, which can be attributed to the presence of hydroxyls and sulfate. A strong chromium enrichment is found in the passive film formed on both alloys: ...

International Nuclear Information System (INIS)

Transmission electron microscopy studies on solution-annealed Alloy 800 revealed small (100-200 nm), spherical-shaped titanium carbide (face centered cubic structure) and large (200 nm-5 #mu#m), faceted titanium nitride (hexagonal structure) particles randomly distributed in the austenite matrix. The volume fraction of former particles was found to be greater than that of the latter. Corrosion studies of the alloy in acidic, chlorides and acidic chloride environments at room temperature indicated that the passivity of Alloy 800 was adversely affected by the addition Cl"- ions. X-ray photoelectron spectroscopy revealed that the surface film formed on the alloy at the onset of passivity consisted of Cr"3"+ (as Cr_2O_3), without any Fe"3"+/Fe"2"+ or Ni"2"+. Scanning electron microscopy studies indicated initiation of pitting at large, faceted particles, not at small, spherical-shaped ones.

International Nuclear Information System (INIS)

Passive films formed on Alloy 690 in different pH solutions at high temperatures were studied by potentiodynamic polarization, Auger electron spectroscopy, thermodynamic diagrams and the Mott-Schottky relation. The chemical compositions and electronic structures of the passive films were found to be strongly pH-dependent. In alkaline solutions, a secondary passivation was clearly observed on potentiodynamic polarization curves. The passive films were a mixture of Cr2O3 and FeCr2O4 below the flat band potential of nickel oxide and were NiFe2O4 above this potential. Electronic structure models, describing the electrochemical properties of the passive films, are proposed and discussed.

Energy Technology Data Exchange (ETDEWEB)

MCrAlY coatings are widely used on hot section components of gas turbines to provide hot corrosion and/or oxidation protection by formation of an oxide layer on the surface. As the protective oxide scale exfoliates during service, aluminum from the coating diffuses outward for reformation of the protective scale. Aluminum may also diffuse inward due to the differences in composition between the coating and the substrate. Thus, the coatings degrade due to oxidation, oxide scale spallation, and inward and outward diffusion of aluminum. Service life of these coatings is controlled by the aluminum content in the coating, operating temperature and start- shutdown cycles. In-service degradation of CoCrAlY and CoNiCrAlY coatings is presented. A procedure to predict the remaining service life of coatings under oxidizing conditions is discussed. (orig.) 12 refs.

International Nuclear Information System (INIS)

We report measurements of the electrical resistivity of the amorphous alloys Fe"4"0Ni"4"0P"1"4B"6 (Metglas 2826), Fe"3"2Ni"3"6Cr"1"4Pr"1"2B"6 (Metglas 2826A) Fe"8"0B"2"0 (Metgals 2605) and Fe"7"5B"2"5 as a function of pressure and temperature. The pressure is varied between 0 and 12 GPa, the temperature between 1.2 and 380 K. At low temperatures the pressure dependence yields additional information on the scattering mechanism. (orig.).

International Nuclear Information System (INIS)

Passive films formed on Alloy 690 in high-temperature alkaline environments were investigated by potentiodynamic polarization, X-ray photoelectron spectroscopy, transmission electron microscopy and Mott-Schottky approach. Passive current density and donor density of the passive films increase with increasing temperature, due to increased diffusion rates of metallic ions and dehydration of hydroxide phases. The passive films show a duplex structure including an inner layer of fine-grained Cr oxide or spinel oxide and an outer layer of Ni-Fe spinel oxide and Ni hydroxide. A growth model of the passive films on Alloy 690 in high-temperature alkaline environments is proposed and discussed.

Energy Technology Data Exchange (ETDEWEB)

Single and binary metal molybdates, supported on silica (80 wt% active phase/20 wt% SiO{sub 2}), having the formula AMoO{sub 4}, where A = Ni, Co, Mg, Mn, and/or Zn, and some ternary molybdates having the formula Ni{sub 0.45}Co{sub 0.45}X{sub 0.066}MoO{sub 4}, where X = P, Bi, Fe, Cr, V, and Ce, were investigated for the oxydehydrogenation of propane to propylene. The reaction is catalytic and is first order in propane disappearance, consistent with the abstraction of a methylene hydrogen being the rate limiting step. Propane conversion and yields of propylene produced vary greatly with the choice of the A metal of the molybdate and the surface area of the catalyst. At 560{degrees}C and atmospheric pressure, the highest propane conversion and highest propylene yields are obtained with NiMoO{sub 4}/SiO{sub 2} (16% at 27% conversion), closely followed by Ni{sub 0.5}Co{sub 0.5}MoO{sub ...

International Nuclear Information System (INIS)

Metastable austenitic steels show excellent mechanical properties, such as high strength combined with excellent ductility and toughness due to martensitic transformation under mechanical loading (transformation induced plasticity effect). A good energy consumption, and, in the case of high-alloyed metastable austenitic steels, a high corrosion resistance, increase the potential of these materials for diverse applications, also in regard of safety requirements. Up to now, numerous wrought alloys were investigated concerning mechanical behaviour, TRIP-effect, martensitic transformation behaviour and modelling of transformation kinetics or stress-strain behaviour. New high alloyed cast CrMnNi-steels, developed at Technical University Bergakademie Freiberg, provide the chance to reduce processing steps, production time and costs. In order to understand the influence of temperature on the martensitic phase transformation behaviour and therefore on mechanical properties ...

Energy Technology Data Exchange (ETDEWEB)

Chloride-induced pitting corrosion of stainless steel (Materials No. 1.4301 and 1.4571) was investigated with the aid of chronopotentiostatic tests. Oxide films upon the surface (temper colours), addition of inhibitors (sulphate and nitrate) and temperature were the testing variables. Two different critical pitting potentials have been found, which give information on the potential ranges for stable passivity, latent and stable pitting corrosion. The results only indicate a small effect of Mo content of the material and test temperature. The inhibitors (sulphate and nitrate) have a marked effect. Specimens with a clean surface produced by pickling are markedly more resistant against pitting corrosion than specimens with a yellow temper colour, whereas the difference in corrosion resistance between yellow and blue films is relatively small. The width of the critical potential range for pitting corrosion generally increases with increasing oxide film thickness. (orig.)

International Nuclear Information System (INIS)

A common evaluation is given for creep crack growth and fatigue crack growth experiments which have been performed at the companies ABB, Siemens-KWU and KFA. The materials under investigation were X10NiCrAlTi32 20 (Alloy 800) and NiCr22Col2Mo (Alloy 617). Several production lots and semi-finished materials as well as welded materials have been tested. Testing techniques differed at the different labs. In order to eliminate the influence of individual testing techniques, material from some production lots was investigated at different labs. The given data cover fatigue crack growth (the materials were tested between room temperature and 1050"oC; the influence of temperature, R-ratio, and frequency was investigated) and creep crack growth (Alloy 800 was tested between 550sup(o)C and 900sup(o)C, Inconel 617 between 800sup(o)C and 1000sup(o)C; the evaluation was done on the basis of the fracture mechanics parameters Ksub(1) and Csup(*)). (Author).

Energy Technology Data Exchange (ETDEWEB)

A new material has been developed for welded low-pressure shafts in steam turbines. Nine test welds were examined in order to confirm the chemical analysis. A shaft disc with an optimized composition was produced and destructively tested. The new material demonstrates, both in a total forging and also in a joint weld examined, excellent strength and toughness characteristics as well as excellent resistance to corrosion. Accordingly, all the requirements for welded low-pressure shafts in steam turbines are fulfilled. (orig.) [Deutsch] Fuer geschweisste Niederdruckwellen in Dampfturbinen wurde ein neuer Werkstoff entwickelt. Zur Festlegung der chemischen Analyse wurden 9 Versuchsschmelzen untersucht. Mit optimierter Zusammensetzung wurde eine Wellenscheibe hergestellt und zerstoerend untersucht. Der neue Werkstoff zeigt sowohl im gesamten Schmiedestueck als auch in einer untersuchten Verbindungsschweissung gute Festigkeits- und Zaehigkeitseigenschaften sowie gute ...

Energy Technology Data Exchange (ETDEWEB)

In a study where the removal of heavy metals from wastewater is the primary aim, the biosorption of heavy metals onto biosolids prepared as Pseudomonas aeruginosa immobilized onto granular activated carbon was investigated in batch and column systems. In the batch system, adsorption equilibriums of heavy metals were reached between 20 and 50 min, and the optimal dosage of biosolids was 0.3 g/L. The biosorption efficiencies were 84, 80, 79, 59 and 42 % for Cr(VI), Ni(II), Cu(II), Zn(II) and Cd(II) ions, respectively. The rate constants of biosorption and pore diffusion of heavy metals were 0.013-0.089 min{sup -1} and 0.026-0.690 min{sup -0.5}. In the column systems, the biosorption efficiencies for all heavy metals increased up to 81-100 %. The affinity of biosorption for various metal ions towards biosolids was decreased in the order: Cr = Ni > Cu > Zn > Cd. (Abstract Copyright ...

International Nuclear Information System (INIS)

As the first step for development of the corrosion resistant superheater tube materials of 500 C, 100 ata used in high efficient waste-to-energy plants, field corrosion tests of six conventional alloys were carried out at metal temperatures of 450 C and 550 C for 700 and 3,000 hours in four typical Japanese waste incineration plants. The test results indicate that austenitic alloys containing approximately 80 wt% [Cr+Ni] show excellent corrosion resistance. When the corrosive environment is severe, intergranular corrosion of 40#approx#200 microm depth occurs in stainless steel and high alloyed materials. It is confirmed quantitatively that corrosion behavior is influenced by environmental corrosion factors such as Cl concentration and thickness of deposits on tube surface, metal temperature, and flue gas temperature. The excellent corrosion resistance of high [Cr+Ni+Mo] alloys such as Alloy 625 is explained by the stability of its protective ...

International Nuclear Information System (INIS)

The potentiodynamic polarization measurement of 254SMO stainless steel (UNS 31254) was conducted in 3.5% NaCl solutions with pH ranging from 0.1 to 5. The results indicated that this stainless steel offered excellent pitting corrosion resistance in corrosive environments. Further, it also exhibited various features on the polarization curves in different pH solutions. The electrochemical constant-potential passivation treatment performed at different pH followed by XPS analysis revealed that the primary constituents of the outermost layer of the passive films formed in the weak (pH 5) and strong (pH 0.8) acid solutions are iron oxides and Cr_2O_3 and Cr(OH)_3, respectively. Molybdenum oxides, primarily in the six-valence state, existed in the outermost layer of the passive film. Only very weak signals corresponding to that of nickel oxides were detected in the film formed in the weak acid (pH 5) solution. The ICP-MS analyses indicated selective ...

International Nuclear Information System (INIS)

Three different techniques for pitting corrosion potential measurement on austenitic stainless steel (Fe18Cr10Ni) were compared: conventional polarization method, a new Avesta electrochemical corrosion measurement cell and a scratch technique. Special attention was paid to the effects of crevice corrosion during pitting corrosion potential measurement and to their elimination. Development of a rapid test technique for reliable pitting corrosion potential determination was aimed at and resulted from comparison of the different techniques.

International Nuclear Information System (INIS)

A few metal complexes of isatin-isonicotinoylhydrazone with Ni(II), Cr(III), Co(II), Cu(II), Zn(II) and Cd(II) have been prepared and characterized on the basis of elemental analyses, infrared and electronic spectra as well as "1H NMR spectra, conductivity and magnetic measurements. In view of the results obtained, it has been found that two molecules of isatin-isonicotinoylhydrazone are chelated to the central metal ion as bis-uninegative ONO tridentate ligand forming non-electrolytic octahedral metal complexes. (author)

International Nuclear Information System (INIS)

Beta-decay studies of the new neutron-rich isotopes sup(58,59)Cr, "6"3Mn, sup(66,67)Co and "6"9Ni, yielding distinctly shorter half-lives than the corresponding theoretical predictions, are presented. The influence of the short half-lives on the r-process calculations of nuclear abundances is discussed. It is concluded that a significantly higher neutron density than the one obtained from explosive helium burning in supernovae is needed to reproduce the observed abundances around A = 80. (orig.).

International Nuclear Information System (INIS)

Mechanical testing of controlled-purity Ni-xCr-9Fe-yC alloys at 360 C revealed an environmental enhancement in IG cracking and time-dependent deformation in high purity and primary water over that exhibited in argon. Dimples on the IG facets indicate a creep void nucleation and growth failure mode. IG cracking was primarily located at the interior of the specimen and not necessarily linked to direct contact with the environment. Controlled potential CERT experiments showed increases in IG cracking as the applied potential decreased, suggesting that hydrogen is detrimental to the mechanical properties. It is proposed that the environment, through the presence of hydrogen, enhances IG cracking by enhancing the matrix dislocation mobility. This is based on observations that dislocation-controlled creep controls the IG cracking of controlled-purity Ni-xCr-9Fe-yC in argon at 360 C and grain boundary cavitation and sliding results that show the ...

International Nuclear Information System (INIS)

Experiments of autogenous laser full penetration welding between dissimilar cast Ni-based superalloy K418 and alloy steel 42CrMo flat plates with 3.5 mm thickness were conducted using a 3 kW continuous wave (CW) Nd:YAG laser. The influences of laser welding velocity, flow rate of side-blow shielding gas, defocusing distance were investigated. Microstructure of the welded seam was characterized by optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) and energy dispersive spectrometer (EDS). Mechanical properties of the welded seam were evaluated by microhardness and tensile strength testing. Results show that high quality full penetration laser-welded joint can be obtained by optimizing the welding velocity, flow rate of shielding gas and defocusing distance. The laser-welded seam have non-equilibrium solidified microstructures consisting of ...

Energy Technology Data Exchange (ETDEWEB)

A necessary condition for crevice corrosion is that a crevice former create a sufficiently tight, restricted geometry on the metal surface to support the development of critical crevice chemistry. Crevice corrosion is affected by the crevice geometry (tightness) and the properties of the crevice former. The objective of this study is to determine the effect of the crevice former material on the evolution of localized corrosion-damage. A standard crevice corrosion test method is modified by (a) the use of ceramic, metal or polymer materials as the crevice former and (b) the variation of size and shape of the crevice. This study focuses on the post initiation stage of crevice corrosion and addresses factors that may limit the initiation of localized corrosion and also slow or stop the continued propagation of corrosion. Controlled crevice corrosion tests are performed under aggressive, accelerated conditions on Ni-Cr-Mo alloy C-22 and other alloys for comparison. ...

International Nuclear Information System (INIS)

K#beta#-to-K#alpha# X-ray intensity ratios of Ti, V, Cr, and Co in pure metals and their disilicide compounds have been measured following excitation by 59.54 keV #gamma#-rays from a 200 mCi "2"4"1Am point-source. The K#beta#-to-K#alpha# intensity ratios of all these metals in the disilicide compounds are found to be less than the corresponding ratios for pure metals. Comparison of the measured K#beta#-to-K#alpha# intensity ratios for the disilicides and pure metals with the multiconfiguration Dirac-Fock calculations indicates increase of the 3d electron populations of Ti, V, Cr, and Co in the disilicides from their pure metal values suggesting the rearrangement of electrons between 3d and 4s states of the individual metal atom. This rearrangement is found to be opposite to that observed in our previously reported work on NiSi_2 and CuSi_2.

Energy Technology Data Exchange (ETDEWEB)

Fe-Cr-Mn stainless steel is one of the candidate materials for the 1`st wall materials and structural applications of fusion reactor as regards reduced radioactivation properties than Fe-Cr-Ni austenitic stainless steels. This report deals with the effects of annealing and aging heat treatment on the microstructure, mechanical properties and corrosion resistance of Fe-Cr-Mn alloys varying Mn and W contents, which were made using vacuum high frequency induction furnace. Increasing Mn contents, austenite phase was increased, and maximum .epsilon. martensite phase was formed at about 21% Mn. W-addition made small amount of ferrite phase in the matrix, and the ferrite contents were increased with raising annealing temperature. Increased Mn contents reduced tensile stress and yield stress but increased the elongation. W-addition raised the high temperature tensile properties. The variation of Mn contents had no influenced on ...

Energy Technology Data Exchange (ETDEWEB)

In order to overcome the inherent disadvantages of Ti-V-based hydrogen storage alloys, such as poor activation behavior and low high-rate dischargeability, the novel composites Ti{sub 0.17}Zr{sub 0.08}V{sub 0.35}Cr{sub 0.1}Ni{sub 0.3}-x wt.% La{sub 0.7}Mg{sub 0.3}Ni{sub 2.75}Co{sub 0.75} (x = 0, 5, 10 and 20) were successfully synthesized by ball milling method in the present study. And the structure and overall electrochemical properties of as-prepared composites are investigated systemically. The electrochemical studies show that the maximum discharge capacity of the composite electrodes displays no variation with the increase of La{sub 0.7}Mg{sub 0.3}Ni{sub 2.75}Co{sub 0.75} content, whereas the high-rate dischargeability (HRD) and the activation behavior are distinctly improved with increasing x. The electrochemical hydrogen kinetics of composite electrodes is also studied by means of ...

Energy Technology Data Exchange (ETDEWEB)

The effect of severe plastic deformation by cold high pressure torsion (HPT) on radio frequency (RF) plasma nitriding of pure iron, as well as St2K50 and X5CrNi1810 steels was investigated. Nitriding was carried out for 3 h in a nitrogen atmosphere at a pressure of 10{sup -5} bar and temperatures of 350 and 400 deg. C. Nitrided specimens were analysed by scanning electron microscopy (SEM), X-ray diffraction and micro hardness measurements. It was found that HPT enhances the effect of nitriding leading almost to doubling of the thickness of the nitrided layer for pure iron and the high alloyed steel. The largest increase in hardness was observed when HPT was combined with RF plasma nitriding at 350 deg. C. In the case of pure iron, the X-ray diffraction spectra showed the formation of {epsilon} and {gamma}' nitrides in the compound layer, with a preferential formation of {gamma}' at the expense of the {alpha}-phase at the higher nitriding ...

International Nuclear Information System (INIS)

1 - Description of program or function: Continuous energy cross-section data library for the Monte Carlo program MCNP based on the ENDF/B-VI Release 3 evaluated nuclear data library (ACE Format). Format: ACE; Number of groups: Continuous energy; Nuclides (107): H-1, H-2, He-4, Li-6, Li-7, Be-9, B-10, B-11, C-nat, N-14, N-15, O-16, O-17, Na-23, Mg-nat, Al-27, Si-nat, Cl-nat, Ti-nat, Cr-50, Cr-52, Cr-53, Cr-54, Mn-55, Fe-54, Fe-56, Fe-57, Fe-58, Co-59, Ni-58, Ni-60, Ni-61, Ni-62, Ni-64, Zr-90, Zr-91, Zr-92, Zr-94, Zr-96, Zr-nat, Nb-93, Mo-94, Mo-95, Mo-96, Mo-97, Mo-nat, Tc-99, Ru-101, Ru-102, Ru-104, Rh-103, Pd-105, Pd-107, Ag-109, I-129, Xe-131, Cs-133, Pr-141, Nd-143, Nd-145, Pm-147, Sm-147, Sm-149, Sm-150, Sm-151, Sm-152, Eu-153, Gd-154, Gd-155, Gd-156, Gd-157, Gd-158, Gd-160, Hf-174, Hf-176, ...

International Nuclear Information System (INIS)

A systematic study for the materials design of III-V and II-VI compound-based ferromagnetic diluted magnetic semiconductors is given based on ab initio calculations within the local spin density approximation. The electronic structures of 3d-transition-metal-atom-doped GaN and Mn-doped InN, InP, InAs, InSb, GaN, GaP, GaAs, GaSb, AlN, AlP, AlAs and AlSb were calculated by the Korringa-Kohn-Rostoker method combined with the coherent potential approximation. It is found that the ferromagnetic ground states are readily achievable in V-, Cr- or Mn-doped GaN without any additional carrier doping treatments, and that InN is the most promising candidate for high-T_C ferromagnet. A simple explanation of the systematic behavior of the magnetic states in III-V and II-VI compound-based diluted magnetic semiconductors is also given. It is also shown that V or Cr-doped ZnS, ZnSe, and ZnTe are ferromagnetic without p- or n-type doping treatment. However, Mn-, ...

Energy Technology Data Exchange (ETDEWEB)

One of the main requirements to use Be as a candidate for plasma facing component in ITER is providing a reliable joint between Be and Cu-alloy heat sink structure. In this work authors present the results of recent activity on this way. To create Be/CuCrZr joints the unique fast e-beam brazing technology was developed in Russia. The numbers of Be/CuCrZr mock-ups were manufactured in Efremov Institute by fast e-beam brazing using Cu-Sn-In-Ni brazing alloy. These mock-ups were tested by Sandia Laboratory at the EBTS electron beam facility. The goals of the tests were to define the allowable dimensions of the armour tiles for the heat loads of more than 10 MW/m{sup 2}, to find the limit of bond strength for the Be/CuCrZr joint and response to heat loads and to estimate the life time of the brazed tiles by thermo-cyclic testing. The screening and thermal fatigue results are presented. With the aim to check ...

Energy Technology Data Exchange (ETDEWEB)

In this work a comprehensive metallophysical study was carried out for two aluminosilicide slip coatings of the systems Al-Si and Al-Nb-Si and an electron-beam Co-Cr-Al-Y coating on alloy EP-539 (17...19% Cr, 4...6% Co, 2.5...4% W, 4.5...6.5% Mo, 2...3% Ti, 3...4% Al, 1.4...2% Nb, balance Ni) after high-temperature testing. The protective properties of the coatings were evaluated from the results of laboratory tests for heat resistance at 1000/sup 0/C in the combustion products of diesel fuel with added sulfur at 970, 1000, and 1060/sup 0/C for 100 h and after full-scale tests for 150, 250, 400, and 700 h. Metallographic, hardness, x-ray, and micro x-ray studies of the coating were carried out. Layer-by-layer phase composition and the lattice spacing of the main phases were determined. X-ray analysis was carried out in an a DRON-1 diffractometer in copper K/sub ..-->../-radiation, and x-ray microanalysis was carried out ...

CERN Document Server

Galactic open clusters are since long recognized as one of the best tools for investigating the radial distribution of iron and other metals. We employed FLAMES at VLT to collect UVES spectra of bright giant stars in a large sample of open clusters, spanning a wide range of Galactocentric distances, ages, and metallicities. We present here the results for four clusters: Berkeley 20 and Berkeley 29, the two most distant clusters in the sample; Collinder 261, the oldest and the one with the minimum Galactocentric distance; Melotte 66. Equivalent width analysis was carried out using the spectral code MOOG and Kurucz model atmospheres to derive abundances of Fe, Al, Mg, Si, Ca, Ti, Cr, Ni, Ba; non-LTE Na abundances were derived by direct line-profile fitting. We obtain subsolar metallicities for the two anticenter clusters Be 20 ([Fe/H]=-0.30, rms=0.02) and Be 29 ([Fe/H]=-0.31, rms=0.03), and for Mel 66 ([Fe/H]=-0.33, rms=0.03), located in the ...

Energy Technology Data Exchange (ETDEWEB)

Transmission electron microscopy studies on solution-annealed Alloy 800 revealed small (100-200 nm), spherical-shaped titanium carbide (face centered cubic structure) and large (200 nm-5 {mu}m), faceted titanium nitride (hexagonal structure) particles randomly distributed in the austenite matrix. The volume fraction of former particles was found to be greater than that of the latter. Corrosion studies of the alloy in acidic, chlorides and acidic chloride environments at room temperature indicated that the passivity of Alloy 800 was adversely affected by the addition Cl{sup -} ions. X-ray photoelectron spectroscopy revealed that the surface film formed on the alloy at the onset of passivity consisted of Cr{sup 3+} (as Cr{sub 2}O{sub 3}), without any Fe{sup 3+}/Fe{sup 2+} or Ni{sup 2+}. Scanning electron microscopy studies indicated initiation of pitting at large, faceted particles, not at small, spherical-shaped ones.

Energy Technology Data Exchange (ETDEWEB)

Trace elemental analysis was carried out in various parts of some anti-diabetic medicinal plants using PIXE technique. A 3 MeV proton beam was used to excite the samples. The elements Cl, K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, Br, Rb and Sr were identified and their concentrations were estimated. The results of the present study provide justification for the usage of these medicinal plants in the treatment of diabetes mellitus (DM) since they are found to contain appreciable amounts of the elements K, Ca, Cr, Mn, Cu, and Zn, which are responsible for potentiating insulin action. Our results show that the analyzed medicinal plants can be considered as potential sources for providing a reasonable amount of the required elements other than diet to the patients of DM. Moreover, these results can be used to set new standards for prescribing the dosage of the herbal drugs prepared from these plant materials.

Energy Technology Data Exchange (ETDEWEB)

In case of airplane engine, technical development like increase of temperature at the turbine entrance or high speed rotation with a purpose of thrust up, and reduction of structural part single substance mass or reduction of number of parts in order to achieve lightness and so forth, has been promoted in order to improve the performance that is evaluated by thrust weight ratio (thrust/weight). Accordingly, research and development of high heat resistance, high strength, lightness and so forth of each material of the parts are in demand. As a representative material corresponding to such demand, L10 type {nu}-TiAl intermetallic compound which is light and has improved high temperature strength properties is paid attention and its development is promotes. The authors were successful for the first time in the world to manufacture composite material with CVD type SiC fiber that was difficult so far by using TiAl-Cr alloy having super plasticity at comparatively low ...

International Nuclear Information System (INIS)

To clarify the acidic and alkaline Intergranular Stress Corrosion Cracking (IGSCC) mechanism of thermally treated alloy 690 (alloy 690 TT) and shot peened alloy 800 (alloy 800 SP), C-ring tests were conducted in deaerated HCl solutions and in deaerated NaOH solutions at 350degC, compared with the acidic and the alkaline IGSCC susceptibilities of mill-annealed alloy 600 (alloy 600 MA), full-sensitized one (alloy 600 FS) and thermally treated one (alloy 600 TT). Grain boundary characteristics, such as chromium depleted zone and chromium carbide precipitation, were examined using modified Huey test and Transmission Electron Microscopy. Potential-pH diagram for Ni, Cr, Fe-H_2O system at 350degC was constructed and the solubilities of NiO, Cr_2O_3 and Fe_3O_4 were also calculated to evaluate the stability of oxide films which were formed on the surfaces of alloy 690, 800 and 600. Under the acidic condition, ...

Energy Technology Data Exchange (ETDEWEB)

Over 100 candidates were examined, including commercial materials and many that were synthesized in house. The mixed oxides were based on Ti, V, Nb, Cr, Mo, W, Mn, Fe, Co, Ni, and Cu doped with other transition metals. A number of individual (single-metal) oxides were included for comparison. The candidates were tested in single cells with Li(Si) anodes and separators based on LiCl-KCl eutectic. Screening was done under constant-current conditions at current densities of 125 me/cm{sup 2} and, to a lesser extent, 50 me/cm{sup 2} at 500 C. Relative performance and limitations of the oxide cathodes are discussed.

International Nuclear Information System (INIS)

The nickel-rich superalloys Alloy 600 and Alloy 800 have been corroded in mildly alkaline deuterated aqueous conditions typical of secondary coolant circuits in a nuclear power station. The oxide films and substrates of these alloys have been analysed by imaging SIMS depth profiling, which makes it possible to describe elemental distribution in all three dimensions. The measurement of the distribution of the secondary ions NiO"-, FeO"- and CrO"- appears useful for detailing the behaviour of nickel, iron and chromium within oxidized phases. The measurement of D"- distribution outlines the extent of oxide hydration. For Alloy 800, evidence of sodium migration into the grain boundaries of the alloy substrate is found. For Alloy 600, no grain boundary sodium ingress can be identified under comparable corrosion conditions. (author).

Energy Technology Data Exchange (ETDEWEB)

We have measured production cross-sections of the new neutron-rich isotopes {sup 58}Ti, {sup 61}V, {sup 63}Cr, {sup 66}Mn, {sup 69}Fe, {sup 71}Co and neighbouring isotopes that have been identified as projectile fragments from reactions between a 500 MeV/u {sup 86}Kr beam and a beryllium target. The isotope identification was performed with the zero-degree magnetic spectrometer FRS at GSI, using in addition time-of-flight and energy-loss measurements. The experimental production cross-sections for the new nuclides and neighbouring isotopes are compared with an empirical parametrization. The resulting prospects for reaching even more neutronrich isotopes, such as the doubly-magic nuclide {sup 78}Ni, are discussed. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Mechanical alloying is an important pre-requisite for the manufacturing of heat resistant oxide-dispersion-strengthened superalloys. Though the microstructure of these materials after hot extrusion and recrystallization treatment is well documented, little is known about the microstructural evolution during ball-milling. A method was tested to prepare electron transparent foils and extraction replica from powder particles for TEM investigations. The microstructure was found to consist of a Ni-Cr-Al solid solution in which submicron particles of refractory metals were embedded. The extremely fine grainize of about 50 nm is the consequence of severe plastic deformation. Yttria particles could not be detected in the powder after ball milling, but after a heat treatment at 1000 C the well-known fine dispersion of oxide particles was evident. (orig.)

International Nuclear Information System (INIS)

Nickel ion radiation at 500 C was shown to have a strong effect on the surface electrochemistry and intergranular corrosion (IGC) of stainless steel (SS). Measured current densities in a 1 N sulfuric acid solution at room temperature were increased at active-passive, passive, and transpassive potentials. Radiation effects on the current decay behavior and susecptibility to IGC were similar for a fine-grained (FG) S alloy and for a very large-grained (LG) SS. Radiation-induced segregation (RIS) at the surface was believed to promote higher currents at short times, whereas segregation at grain boundaries was responsible for IG attack. Analytical electron microscopy (AEM) measurements revealed chromium and iron depletion plus Ni and silicon enrichment at grain boundaries in irradiated specimens. Si enhanced dissolution at transpassive potentials, whereas Cr depletion did the same at active-passive and passive potentials.

International Nuclear Information System (INIS)

The potential material class for use at 600"0C and more, e.g. for steam turbines with improved thermal efficiency, are austenitic steels. Using these steels with welded joints, it is to be considered that, by superposition of weld residual stresses and service stresses, extensive creep strains - and in the worst case crack formation - can occur locally. To assess the influence of these effects on service behaviour, different material states of CrNi-steels and Incoloy 800 were investigated with respect to strength, ductility and, especially, to crack and creep crack growth in the temperature range around 600"0C. It is shown that creep embrittlement, not microstructural changes as effected by weld heat input, causes heat affected zone (HAZ)-reheat cracking. Creep embrittlement can be avoided by special design and fabrication rules. (orig.).

International Nuclear Information System (INIS)

As a contribution to the US/Japan cooperative program in fusion neutronics, we have prepared a library of multigroup neutron cross sections, scattering matrices, and covariances (uncertainties and their correlations). This 74-group library, called COVFILS-2, is being used at Los Alamos and at the University of California at Los Angeles in the sensitivity and uncertainty analysis of the Li_2O integral experiment recently performed at the Fast Neutron Source (FNS) in Japan. Another intended use of this library is in the estimation of the uncertainty in key performance parameters (such as breeding ratio) of conceptual fusion reactors. The 14 materials included in the first version of COVFILS-2 are H, "6Li, "7Li, Be, C, N, O, Na, Al, Si, Cr, Fe, Ni, and Pb.

International Nuclear Information System (INIS)

A new evaluation of the 1% time strain limit for creep strength and the isochronous stress/strain relationship was to be undertaken for the type 800 alloy, based on up to date experimental data. After the evaluation of the 1% time strain limit curves and time fracture curves of individual melts, multilinear regression analyses were made to clear up the relationship between parameters of the creep behaviour such as creep strength, 1% time strain limit and time fracture strain on the one hand and metallurgical parameters such as C, Ti, Al, Ni, Cr contents or grain size and type of manufacture, on the other hand. Based on the knowledge gained from these calculations, new limits were determined for HTR material specifications for variants of the 800 alloy of the Rk, NT, DE, and HT type. (orig./DG).

Energy Technology Data Exchange (ETDEWEB)

The carbon transfer has been analyzed in the Alloy 800/sodium/stainless steel system by determining the carbon-uptake of Alloy 800 foils, which were exposed in liquid sodium of known carburizing potential. Under equilibrium conditions between 650 and 550/sup 0/C the measured total carbon concentrations in the Alloy 800 tabs were found to be roughly related to the carbon activities of the sodium environment by the equation already stated for the 18 Cr-8/10 Ni stainless steels, extrapolated to the chemical composition of the Ni-rich austenitic alloy. However the Alloy 800 was not found to undergo any decarburization in low-carbon activity environments. The carbon diffusion kinetics was determined as a function of temperature, it was found to be similar to that reported for the AISI-304 type of steel. The effects of sodium exposure on microstructural and mechanical properties of several Alloy 800 heats were examined at 550/sup ...

Science.gov (United States)

... ADD137758. Title : The Oxidation Behavior of CoCrAlY, CoCrAl and Yttrium-Implanted CoCrAl Alloys Compared and Contrasted,. ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, we report on a comparative study of active screen plasma nitriding (ASPN) and conventional dc plasma nitriding (CPN) behavior of 30CrNiMo8 low-alloy steel that has been examined under various process conditions. The process variables included active screen setup parameters (screen and iron plate top lids placed on the screen setup with 8 mm of hole size), treatment temperature (550 and 580 deg. C), gas mixture (75/25 and 25/75 of N{sub 2}/H{sub 2}) and treatment time (5 and 10 h) in 500 Pa pressure. The structure and phases composition of the diffusion zone and compound layer were studied by X-ray diffraction (XRD), microhardness tests, light optical microscopy and scanning electron microscopy (SEM). It was observed that treated sample surfaces in both CPN and ASPN methods consist of {gamma}' and {epsilon} phases, and while the nitriding time and/or temperature increases, the intensity of {epsilon} phase in the compound layer will increase ...

International Nuclear Information System (INIS)

In the present paper the contamination levels of trace and toxic metals in drinking water collected from Tarapur industrial area, Thane were investigated. The concentrations of trace and toxic metals (Pb, Cd, Cu, Cr, Ni, Se, V, Zn, Mn, Mo, Co, As and Ba) were determined simultaneously using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES). The results were compared with international water quality guidelines (WHO, 2008) and were found within the permissible limits. The quality assurance was checked by standard addition method and spike recovery. The concentration of Pb, Cd, Cu, Cr, Ni, Se, V, Zn, Mn, Mo, Co, As and Ba varies from 4.25-19.62 #mu#g/L, 0.13-1.49 #mu#g/L, 0.60-65.55 #mu#g/L, 0.46-4.15 #mu#g/L, <0.1 #mu#g/L, 0.5- 9.35 #mu#g/L, <0.5 #mu#g/L, 3.41-99.64 #mu#g/L, 0.80-9.62 #mu#g/L, 0.30-1.48 #mu#g/L, <0.1-0.90 #mu#g/L, <0.63 #mu#g/L and 0.71-9.0 #mu#g/L ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is to account for the effects of the high temperature oxidation of metals on their microstructure and their mechanical properties. 'Model' materials like pure nickel, pure iron and the Ni-20Cr alloy are studied. Nickel foils have been oxidised at 1000 C on one side only in laboratory air, the other side being protected from oxidation by a reducing atmosphere. After the oxidation treatment, the unoxidized face was carefully examined by using an Atomic Force Microscope (AFM). Grain boundaries grooves were characterised and their depth were compared to the ones obtained on the same sample heat treated in the reducing atmosphere during the same time. They are found to be much deeper in the case of the single side oxidised samples. It is shown that this additional grooving is directly linked to the growth of the oxide scale on the opposite side and that it can be explained by the diffusion of the vacancies ...

Energy Technology Data Exchange (ETDEWEB)

A two-year demonstration run of a 500 C/100kgf/cm{sup 2}{center_dot}g high-efficiency waste-to-energy pilot plant has been started from February 1998; this plant represents as the final stage of the NEDO project of development of a high-efficiency waste-to-energy plant. Alloy 625 (SB444) and 310 HCbN tubings were selected for the 3rd and 2nd superheater of the pilot plant, respectively, and ten kinds of conventional and new solid-wall tubings, weld overlayed tubings, composite tubings, and cermet spray coated tubings were tested. By means of 6000-hour field corrosion test in three typical domestic plants, material life and corrosion environment for superheater tubings installed in the pilot plant were evaluated. Also, the effect of alloying elements Cr, Ni, Mo, corrosion rate law, etc. were investigated in detail. Furthermore, the design conception and basic performance of the pilot plant regarding pollution control and corrosion prevention ...

International Nuclear Information System (INIS)

The main compositions of iron-base amorphous self-fluxing alloy powders of 150 mesh, used in this work, are Fe, Cr, Ni, W, Mo, B, Si and C. The ranges of each element in at% are (65-70)Fe, (3-5)Cr, (2-4)Ni, (2-4)W, (1-2)Mo, (10-14)B, (4-7)Si and (2-3)C. The atomic ratio of metal-metalloid is about 80:20, so this alloy is abbreviated as M_8_0X_2_0. The material on which coatings were deposited is 1020 steel, austenitized for 1h at 880 C, water quenched, and tempered at 180 C for 1h. This heat treatment resulted in a low carbon martensite structure with a hardness of HRC35-45. After cleaning, shot blasting and preheating the steel to about 200 C, the authors sprayed a thin Ni-Al alloy layer of about 0.1--0.15mm in thickness onto the specimen by means of an oxygen-acetylene torch to provide better bonding of the coating with substrate. Then the M_8_0X_2_0 and M_8_0X_2_0+8%CeO_2 alloy ...

Energy Technology Data Exchange (ETDEWEB)

We have described the x-ray optics and beamline performance of the ANL X6B beam line at the NSLS. Considerable flexibility has been built into the beam line to accommodate a wide range of x-ray diffraction, scattering, and spectroscopy experiments with various requirements. We presented selected examples of experimental results and showed that with the high intensity, high energy resolution, high-q resolution, and energy tunability, the X6B beam line has become a versatile facility.

Energy Technology Data Exchange (ETDEWEB)

Single and binary metal molybdates of the formula AMoO{sub 4}, where A=Ni, Co, Mg,Mn and/or Zn, were investigated for the oxydehydrogenation of propane to propylene, as well as some ternary molybdates of the formula NiO{sub 0.45}Co{sub 0.45}X{sub 0.066}MoO{sub 4} where X=P, Bi, Fe, Cr, V and Ce. All catalysts were supported on SiO{sub 2} with an active phase/support ratio of 80/20 (wt%). The reaction is catalytic and not a gas phase initiated reaction. It is first order in propane, consistent with the abstraction of the methylene hydrogen being the rate limiting step. Propane conversions and propylene yields vary greatly depending on the metal of the molybdate and surface area of the catalyst. Highest propylene yields (16% at 26.6% propane conversion) are obtained with NiMoO{sub 4}/SiO{sub 2}. Conversion and yield are significantly influenced by the molybdenum content of the compositions. The effect is ...

Energy Technology Data Exchange (ETDEWEB)

Austenitic stainless steel (18% Cr, 12% Ni, Mo gradation between 0,06 to 3,6%) had been solution nitrided. By step-by-step removing, the samples could be prepared with various surface contents of nitrogen from 0.04 to 0.42%. In two test series the influence of nitrogen had been determined. The susceptibility against pitting corrosion of these samples had been tested by the chronopotentiostatical method. For the investigated steel composition and the used corrosion system there is no influence of molybdenum on the effectiveness of nitrogen. The effectiveness of nitrogen can be described by the factor 25 in the PRE. By the investigation of the surfaces with the XPS analysis, it could be shown that the passivation and the pit nucleation is influenced by nitrogen. In these ranges NO{sub x}, NH{sub x}, and NH{sub z}-spectra have been detected. Bound Mo was found in steels containing molybdenum. It is assumed that the repassivation mechanisms of N ...

International Nuclear Information System (INIS)

The formation of thin SiO_2 layers on silicon and metal silicides was studied by phase- and thickness measurements with Rutherford back-scattering of 2 MeV alfa particles. Thermal oxidation was done in steam and dry oxygen at temperatures between 750 degrees Celsius and 1 100 degrees Celsius, while SiO_2 formation at room temperature was carried out by anodic oxidation. The study of silicon oxidation was done on Si<100>, Si<111> and amorphous silicon substrates. Thermal oxidation of CoSi_2, CrSi_2, NiSi_2, PtSi and TiSi_2 was investigated. The oxidation rates of the silicides were found to be much higher than for silicon. The oxidation process is also diffusion-limited with a higher oxidation rate for steam as compared to dry oxygen. The silicide layers were found to stay intact during thermal oxidation. A certain amount of structural and chemical instability did appear. Chemical instabiliy was shown by metal oxidation which led to ...

Energy Technology Data Exchange (ETDEWEB)

Austenitic stainless steels have been implanted with molybdenum ions (Mo[sup +], 100 keV, 2.5 x 10[sup 16] atoms cm[sup -2]). The implanted material has been characterized by XPS and RBS. The implanted region has a thickness of [approx] 1000 A with a maximum molybdenum concentration of [approx] 9 at.% Mo located at [approx] 210 A from the surface. The effects of implanted molybdenum on the passivation of the alloy in 0.5 M H[sub 2]SO[sub 4] have been investigated by electrochemistry and XPS. After XPS analysis the samples were transferred without exposure to air into a glove-box with an inert atmosphere. The electrochemical behaviour of the alloy is significantly modified by the implanted molybdenum. The major effect is that the activation peak disappears. A bilayer structure (outer hydroxide/inner oxide) of the passive film is observed for both the implanted and non-implanted alloys and the thicknesses of the films are similar. On the implanted alloy the outer hydroxide layer contains ...

Energy Technology Data Exchange (ETDEWEB)

This work presents a comparative study of low-alloy steel nitriding for different possible techniques. Active screen plasma nitriding (ASPN) is a successful surface modification method that has many advantages over the conventional DC plasma nitriding (CPN). The corrosion behavior of 30CrNiMo8 low-alloy steel has been examined using anodic polarization tests in 3.5% NaCl solution under varying conditions of ASPN and CPN processes. The process variables included active screen setup parameters, treatment temperature (550 and 580 deg. C), gas mixture (25/75 and 75/25 of N{sub 2}/H{sub 2}) and treatment time (5 and 10 h) in 500 Pa pressure. The structure and phases composition of the compound layer was studied by X-ray diffraction (XRD), microhardness tests, optical microscopy and scanning electron microscopy (SEM). It was observed that ASPN treated samples surface enhanced corrosion resistance while the temperature and/or hole size of screen setup increased.

Energy Technology Data Exchange (ETDEWEB)

The effect of temperature (60-280{sup o}C) on the properties of the oxide films formed on Alloy 800 in 0.1 M NaCl and 0.1 M Na{sub 2}SO{sub 4} aqueous solutions was studied by in situ AC impedance spectroscopy and polarization in the Fe(CN{sub 6}){sup -3}/Fe(CN){sub 6}{sup -4} redox system. The anodic behavior under the same experimental conditions was examined by potentiodynamic polarization techniques. In both solutions the passive film was found to become more porous, and hence less protective, with increasing temperature. However, at temperatures above 150{sup o}C, the loss of film protectiveness is more pronounced in chloride solutions, in which pitting occurs. Pitting morphology was found to be strongly temperature dependent: isolated and deep pits were found up to 200{sup o}C whereas at higher temperatures a broad, shallow and more generalized type of attack was detected. No effect of temperature on the defect structure of the semiconductor oxide film was found. It was concluded ...

Energy Technology Data Exchange (ETDEWEB)

A single crystalline ternary nanostructure having the formula A.sub.xB.sub.yO.sub.z, wherein x ranges from 0.25 to 24, and y ranges from 1.5 to 40, and wherein A and B are independently selected from the group consisting of Ag, Al, As, Au, B, Ba, Br, Ca, Cd, Ce, Cl, Cm, Co, Cr, Cs, Cu, Dy, Er, Eu, F, Fe, Ga, Gd, Ge, Hf, Ho, I, In, Ir, K, La, Li, Lu, Mg, Mn, Mo, Na, Nb, Nd, Ni, Os, P, Pb, Pd, Pr, Pt, Rb, Re, Rh, Ru, S, Sb, Sc, Se, Si, Sm, Sn, Sr, Ta, Tb, Tc, Te, Ti, Tl, Tm, U, V, W, Y, Yb, and Zn, wherein the nanostructure is at least 95% free of defects and/or dislocations.

International Nuclear Information System (INIS)

Repassivation behavior and IGA resistance of nickel base alloys containing 0#approx#30 wt% chromium was investigated in high temperature acid sulfate solution. (1) The repassivation rate was increased with increasing chromium content. And so the amounts of charge caused by the metal dissolution were decreased with increasing chromium content. (2) Mill-annealed Alloy 600 suffered IGA at low pH environment below about 3.5 at the fixed potentials above the corrosion potential in 10%Na_2SO_4+H_2SO_4 solution at 598K. On the other hand, thermally-treated Alloy 690 was hard to occur IGA at low pH environments which mill-annealed Alloy 600 occurred IGA. (3) It was considered that the reason, why nickel base alloys containing high chromium content such as Alloy 690 (60%Ni-30%Cr-10%Fe) had high IGA/SCC resistance in high temperature acidic solution containing sulfate ion, is due to both the promotion of the repassivation and the suppression of the film ...

Energy Technology Data Exchange (ETDEWEB)

Simultaneous nitriding and ageing heat treatments of precipitation hardenable tool steel was carried out inside a DC-pulsed plasma nitriding reactor. A single heat treatment cycle was done, as the plasma nitriding and age hardening processes occur approximately at the same ranges of temperatures and times. Specimens of Cr-Ni-Mo-Al age hardenable steel, in the solubilized and solubilized and aged conditions, were tested. Plasma nitriding and ageing, carried out at 500 deg. C for times ranging between 2 and 8 h, increased the surface hardness up to 1000 HV, producing case depths between 100 and 200 {mu}m. The core hardness of solubilized samples increased from 30 to 39 Rockwell C after the plasma nitriding treatment proving the possibility of nitriding and ageing at the same treatment cycle. The pre-aged samples did not show any overageing after the simultaneous plasma nitriding and ageing treatments. The corrosion resistance after plasma nitriding increases when the ...

International Nuclear Information System (INIS)

Secondary ion mass spectrometry (SIMS) has been used to investigate changes that occur in an advanced Ir-0.3W alloy during high temperature aging. This alloy is used to clad "2"3"8PuO_2 heat sources used in thermoelectric generators for deep space reconnaissance satellites. Long-term direct contact with PuO_2 at 1400"0C leads to physical and chemical changes within the cladding alloy that affect its metallurgical properties. SIMS was used to show that Cr, Fe, Ni, and in some cases O, diffuse from the PuO_2 into the alloy. Thorium and aluminum diffuse out of the alloy in these same regions. This SIMS study suggests that inward O diffusion and subsequent formation of ThO_2 on grain boundaries may stabilize the alloy against enhanced grain growth.

Energy Technology Data Exchange (ETDEWEB)

The INCO ``INCOLOY 800`` trademark groups the Fe-Cr-Ni alloys containing 30 to 35% nickel, 19 to 23% chromium, 0,15 to 0,60% aluminium, 0,15 to 0,60% titanium and less than 0,10% carbon contents, used as construction materials for condenser and heat exchanger tubes. In parallel with water chemistry control and studies aimed at reducing the residual stresses resulting from tube expansion, studies have been conducted to a better understanding of this alloy, its metallurgy and its corrosion behaviour under accurately defined fabrication and heat treatment conditions. The purpose of this paper is to present the results of a behaviour study of INDRET alloy 800 concerning isothermal relaxation and effects of the said relaxation heat treatments on alloy microstructure studied with a transmission electron-chemical method to determine the sensitiveness to intergranular corrosion, and by electrochemistry in pressurized hot water. (authors). 4 figs., 5 tabs., 7 refs.

International Nuclear Information System (INIS)

The corrosion resistance of zircaloy is affected by conditions of heat treatment in the manufacturing steps to be formed into a final product as a structural material. In the manufacturing method of the present invention, a Zr alloy controlled to contain Sn: 0.8 to 1.2wt%, Fe: 0.17 to 0.28wt%, Cr: 0.05 to 0.15wt%, Ni: 0.04 to 0.10wt%, Nb: 0.01 to 0.09wt%, oxygen: 1,000 to 1,500ppm and Si, an Si impurity at a concentration of 120ppm or less and balance of Zr is melted into a cast piece, to which #beta# hardening is applied. Then, rolling and annealing treatment are applied so that the total heat input amount to the material: #SIGMA#Ai ranges from 1 x 10"-"1"9 to 1 x 10"-"1"7. With such procedures, a Zr alloy structural material for a reactor core having excellent homogeneous corrosion resistance and hydrogen absorption resistance for a long period of time while having a sufficient strength can be obtained even in a case where Sn content is ...

Energy Technology Data Exchange (ETDEWEB)

Alloy 800 is an austenitic Fe-Ni-Cr steel containing relatively minor but important amounts of carbon, aluminium and titanium. Special grades of alloy 800 known as 800H, 800HT and 800LC differ in the concentrations of these elements. In addition to these industrial specifications, further melts were prepared containing phosphorous or sulphur. Using a radioactive tracer method the bulk and grain-boundary diffusion of {sup 59}Fe was investigated in these alloys in the temperature range 800 to 1000 C. For evaluation of the diffusion profiles the approximation of Suzuoka was used, which considers the depletion of the tracer on the surface. By autoradiography it was confirmed that such depletion occurs. In alloy 800H the activation energy of grain-boundary diffusion of {sup 59}Fe was found to be (209{+-}17) kJ/mol; dissolved elements, especially phosphorous, increase the activation energy. The same materials - aged at 800 C for 100 h - were used for creep experiments at ...

Energy Technology Data Exchange (ETDEWEB)

In the course of the research project 'Investigations of trace element concentrations in coal seams with different mineral groups', 31 seam coals of the Ruhr Carboniferous were analysed in order to determine the bending of 14 coal-relevant trace elements to the mineral groups and/or minerals of the coals. Products with different ash content were produced by fluctuation of the seam coals in a laboratory cell. The raw coals and fluctuation component products were analyzed chemically and mineralogically in order to get a quantitative raw material characterisation of the sampled material. Particular interest is taken in the chemical and non-ecological composition of the mineral as ash carrier in the coal and the fluctuation component products, as well as in trace element control. (orig./EF).

International Nuclear Information System (INIS)

The rates of hydrogen release from simulated high-level liquid waste (SHLLW) during irradiation of "6"0Co #gamma#-rays have been studied using a laboratory-scale apparatus. The SHLLW used was made up of 28 different metal elements, the concentrations of which were determined from a computed data (ORIGEN-2) for a Purex spent fuel (burn-up of 4.5 GWd/t, cooling time of 4 years) except for those of corrosion products (Fe, Cr and Ni) and of chemical process additive (P). The nitrate ion concentration of the SHLLW was 4.97 M. The G-value of hydrogen release was 0.0164 for stirred conditions, but for nonstirred conditions with dose rate : 2.8 kGy/h and with the SHLLW solution height more than 8 cm, the following relation was found between the G-value and the solution height (d cm); G(H_2) = 0.100 d"-"1"."6. The G-values of oxygen and nitrogen releases were also determined. (author).

Energy Technology Data Exchange (ETDEWEB)

Described herein are effects of nitrogen dissolved in steel on passivity and pitting corrosion, as one of the major corrosion phenomena observed in stainless steel. Mechanisms involved in controlling pitting corrosion by nitrogen are also discussed. Nitrogen contained in austenic stainless steel is concentrated in the surface area, in particular in the vicinity of the interface between the passive film and metal matrix. Nitrogen tends to decrease critical current density in an acid, when it is added to steel of high critical current density (approximately 1mA/cm{sup 2} or higher). This phenomenon is considered to result from accumulation of nitrogen preferentially in the surface area to prevent dissolution of steel. Nitrogen dissolved in the austenic phase improves resistance of the steel to pitting corrosion. This phenomenon is considered to result from controlled decrease in pH level during the initial stage of pitting corrosion, characterized by evolution of micropits, to help ...

International Nuclear Information System (INIS)

Impurities (Ca, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Ti, Y, Zn and Zr) in sialon powder were determined by the following procedure: A sample (0.5 g) was heated with a mixture of hydrofluoric acid (3 ml) and nitric acid (1 ml) in a Teflon pressure vessel at 170degC for 16 h. The contents of the vessel were transferred into a platinum crucible containing phosphoric acid (4 ml) and heated on a hot plate until the opaque appearance of the content changed to a clear-syrupy fluid. The fluid was diluted to 100 ml with water and used for ICP-AES analysis of all impurity elements except K, which was determined by AAS. It was necessary to match closely the matrix concentrations (H_3PO_4, Al and/or Y) of the standard solutions with those of sialon sample solutions for the determination of impurities because of interferences of the matrix components. This method was successfully applied to the determination of impurities in commercial sialon samples. (author).

Energy Technology Data Exchange (ETDEWEB)

This patent describes an energy storage device. It comprises: a working electrode, a counter electrode, electrically isolated from the working electrode; an electrolyte in contact with the working electrode and the counter electrode, and means for collecting electrical current therefrom; the working electrode consisting essentially of an amorphous metal alloy of the formula: A{sub {ital a}}M{sub {ital b}}M{prime}{sub {ital c}}, wherein A is at least one metal selected from the group consisting of Ag, Hg and Pt; M is at least one metal selected from the group consisting of Pb, Cu, Cr, Mo, W, Ni, Al, Co, Fe, Zn, Ru, Cd and Mn; M{prime} is at lest one of the elements selected from the group consisting of Ca, Mg, Ti, Zr, Hf, V, Nb and Ta; and wherein a ranges from about 0.005 to about 0.80; b ranges from 0.05 to about 0.70; and c ranges from about 0.08 to about 0.95.

Energy Technology Data Exchange (ETDEWEB)

The aim of the presented investigation was to gain information about the behaviour of the initiation and growth of intercrystalline creep cracks during creep deformation from the evaluation of metallographic micrographs. The austenitic steel X10 NiCrAlTi 32 20 HT (Alloy 800 HT) was investigated by carrying out creep tests at 800 and 900 C with different nominal stresses until fracture. Additional tests are carried out on certain creep strains in the late tertiary creep stage. The creep tests are followed by a metallographic investigation of the crept specimens. The statistical distribution of the microcrack lengths was used to estimate the rate of crack initiation and crack growth. It is found that the rate of growth of the intercrystalline creep cracks in Alloy 800 HT is dependent on the applied stress and the creep strain reached. The rate of growth of long cracks was only slightly higher than that of short cracks and was lower than predictions based on fracture ...

Energy Technology Data Exchange (ETDEWEB)

Out of the R and D of mesoscopic metal group composite materials, the paper described the fiscal 1997 results. In the in-situ method as a composite material making method, elucidated to some degree were chemical composition of Fe-C-Cr-V-Nb-Mo-W-Ni base multi-dimensional alloys, and wear resistance and oxidation resistance of MC type carbide dispersion multi-phase texture crystallizing as primary crystal and eutectic. In the composite material making with ceramic fiber and alloy by the pressure infiltration method, the paper clarified the texture formation mechanism in solidification/heat treatment by a combination of Al alloys and alumina long fiber, and the relation between fiber configuration and wear resistance. By MA and MG methods as the powder metallurgy composite material making method, a composed body of {alpha}-stainless steel of Fe-12%Cr composition and M23C6 of 40-90vol% are designed for alloy composition, and powder of amorphous or ...

International Nuclear Information System (INIS)

Photoelectrochemical current response of passive film was investigated for pure Cr and Fe-xCr (x = 8, 14, 18) alloys polarised potentiostatically in 0.1 kmol m"-"3 H_2SO_4 solution. Photoelectrochemical action spectrum could be separated into two or three constituents. These components were considered to be derived from Cr_2O_3 (E_g"o"p"t#propor to#3.6 eV) and Cr(OH)_3 (E_g"o"p"t#propor to#2.5 eV), and possibly CrO OH. The optical band gap, E_g"o"p"t, of each component was almost constant for various applied potentials, polarisation periods, and substrate materials. Flat band potential E_j_b at which the polarity of photocurrent changes from negative to positive with increasing potential was determined for each phase. E_j_b for Cr(OH)_3 on Cr and Fe-Cr alloys was about 250 mV_A_g_/_A_g_C_l. E_j_b for ...

International Nuclear Information System (INIS)

A nitric acid solution containing Cr_2O_7"2"- ion is used for a corrosion test which simulates the condition in a nuclear fuel reprocessing plant. As the effect of Cr content on the corrosion resistance of stainless steel is not yet fully understood in that solution, the effects of Cr content in an alloy and that of Cr_2O_7"2"- ion in nitric acid on the corrosion rate were studied by using electro-chemical measurements. The increase of Cr content reduced the general corrosion rate in nitric acid solution without Cr_2O_7"2"- ion, however it increased that in nitric acid solution containing Cr_2O_7"2"- ion. It is considered that the reversal of the Cr content dependency is due to a rise of the corrosion potential caused by addition of Cr_2O_7"2"- ion to the potential region where a high ...

Energy Technology Data Exchange (ETDEWEB)

The K{beta}-to-K{alpha} X-ray intensity ratio of Ni in Ni{sub 3}Si, Ni{sub 2}Si and NiSi has been determined by energy dispersive X-ray fluorescence technique. It is found that the intensity ratio of Ni decreases from pure Ni to Ni{sub 2}Si and then increases from Ni{sub 2}Si to NiSi, in good agreement with the electronic structure calculations cited in the literature. We have also performed band structure calculations for pure Ni in various atomic configurations by means of linear muffin-tin orbital method and used this data with the normalized theoretical intensity ratios cited in the literature to estimate the 3d-occupation numbers of Ni in Ni-Si alloys. It is emphasized that investigation of alloying effect in terms of X-ray intensity ...

International Nuclear Information System (INIS)

We have performed extended X-ray absorption fine structure (EXAFS) analysis for artificial Cr-goethite to elucidate the local structure around Cr in Cr-goethite. The spectra were obtained using synchrotron radiation X-rays at the Photon Factory in Tsukuba. The first shell contributions were isolated by Fourier filtering EXAFS data, and the inverse Fourier transformed single-shell data were analyzed using a curve fitting method. The results show that Cr is coordinated with (7#+-#1)O"2"- ions. The protective characteristics of the Cr-goethite protective rust layer on weathering steel can be interpreted in terms of the O"2"- coordination around Cr"3"+ resulting in the creation of negative fixed charge in the Cr-goethite particles. (author)

Energy Technology Data Exchange (ETDEWEB)

The exchange charge model of crystal field theory has been used to analyze systematically the ground state absorption spectra of octahedrally coordinated Ni{sup 2+} ion in isostructural nickel halide crystals NiCl{sub 2}, NiBr{sub 2}, and NiI{sub 2}. The parameters of the crystal field acting on the Ni{sup 2+} ion are calculated from the available crystal structure data. The obtained energy level schemes are compared with experimental absorption spectra; a good agreement with experimental data is demonstrated. Dependencies of the crystal field invariants and covalence effects on the type of ligands are considered. It is shown numerically that the overlap effects between Ni{sup 2+} ion and ligands increase with an increase of the ligands' atomic number resulting in the following order of the degree of covalence: NiI{sub ...

International Nuclear Information System (INIS)

1 - Description of program or function: Format: MATXS; Number of groups: 175 neutron-, 42 photon-groups; 176 Nuclides: 1-H-1, 1-H-2, 1-H-3, 2-He-3, 2-He-4, 3-Li-6, 3-Li-7, 4-Be-9, 5-B-10, 5-B-11, 6-C- nat., 7-N-14, 7-N-15, 8-O-16, 8-O-17, 9-F-19, 11-Na-23, 12-Mg-nat., 13-Al-27, 14-Si-nat., 14-Si-28, 14-Si-29, 14-Si-30, 15-P-31, 16-S-32, 17-Cl-nat., 19-K-nat., 20-Ca-nat., 21-Sc-45, 22-Ti-nat., 23-V-nat., 24-Cr-50, 24-Cr-52, 24-Cr-53, 24-Cr-54, 25-Mn-25, 26-Fe-54, 26-Fe-56, 26-Fe-57, 26-Fe-58, 27-Co-59, 28-Ni-58, 28-Ni-60, 28-Ni-61, 28-Ni-62, 28-Ni-64, 29-Cu-63, 29-Cu-65, 31-Ga-nat., 39-Y-89, 40-Zr-nat., 40-Zr-90, 40-Zr-91, 40-Zr-92, 40-Zr-94, 40-Zr-96, 41-Nb-93, 42-Mo-nat., 46-Pd-102, 46-Pd-104, 46-Pd-105, 46-Pd-106, 46-Pd-108, 46-Pd-110, 47-Ag-107, 47-Ag-109, 48-Cd-106, 48-Cd-108, 48-Cd-110, ...

International Nuclear Information System (INIS)

The intensity of luminescence from the "2E state of Cr(bpy)_3"3"+ (bpy = 2, 2'-bipyridine) is lower in D_2O, although the "2E lifetime is unchanged, indicating that the "4T_2 (precursor to "2E) is sensitive to the isotopic nature of the solvent. A photophysical mechanism is proposed for Cr(NN)_3"3"+ complexes.

International Nuclear Information System (INIS)

The hydrogen evolution reaction (HER) was studied on bare brass (B), nickel coated brass (B/Ni), nickel-zinc alloy coated brass (B/NiZn, leached Zn), nickel (under layer)/nickel-zinc alloy coated (top layer) brass electrodes (B/Ni/NiZn, leached Zn) in 1 M NaOH solution using electrolysis, cathodic polarization and electrochemical impedance spectroscopy (EIS) techniques. Long term tests were performed in order to evaluate the electrocatalytic activity and corrosion performance of the prepared electrodes with operation time. The results showed that leached electrodes, especially B/Ni/NiZn electrode, have a smaller overpotential than the others and a good electrocatalytic activity for the HER. Its electrocatalytic activity is also stable over electrolysis time. Contrary to the HER performance, B/NiZn cannot provide an adequate corrosion protection. However, when a thin ...

Energy Technology Data Exchange (ETDEWEB)

We present the synthesis, magnetic and UV spectrometry of NiZn-ferrite nanofiber. The single phase of spinel ferrite was obtained at 600 {sup o}C. The NiZn-ferrite fibers fabricated by an electrospinning process were formed as a polygonal grain growth with firing temperature in fiber matrix. It appeared that the saturation magnetization (M{sub S}) of NiZn-ferrite nanofiber was dependent on Ni/Zn molar ratio which is similar to that of the inverse spinel ferrites. The NiZn-ferrite fibers showed good DNA adsorption efficiency that can be modified and utilized for DNA separation with magnetic nanofiber as a novel material in clinical applications.

International Nuclear Information System (INIS)

The size distributions of precipitated Ni clusters on the surface of a LaNi_5-based alloy immersed in alkaline solution (alkaline treatment) at 383 K for 0-110 min were precisely determined by combining superparamagnetic analysis and transmission electron microscopy (TEM) observations. The superparamagnetic analysis indicated that the diameters of the Ni clusters were smaller than #approx#25 nm in all samples, while their average values increased approximately from 5 to 9 nm with increasing alkaline treatment time. The spatial distribution of the Ni clusters was successively observed by TEM, which agreed fairly well with the estimated size distribution by superparamagnetic analysis. Therefore, estimation of the actual size distribution of Ni clusters by superparamagnetic analysis was proved to be feasible. Based on the above results, a precipitation process for ...

Energy Technology Data Exchange (ETDEWEB)

A simple and rapid method is described for the determination of major and trace elements in rock and sediment samples by wavelength dispersive XRF. Sample measured were made from cellulose powder pressed into 4 cm diameter aluminium ring 0.4 t cm/sup -2/, and then 1 g of powdered sample (0.08 g cm/sup -2/) was placed on the disk and repressed at 1.6 t cm/sup -2/. X-ray measurements were performed for total XRF intensity (I/sub p/) at the characteristic line of each element and background intensity (I/sub b/) in vicinity of the line. The correction of matrix effect was achieved by X-ray intensity ratio of peak to background for each element. Eight standard rock samples from Geological Survey of Japan were used as standard materials, and linear calibration curves were obtained by the plot of I/sub p/ - I/sub b/ vs. concentration for Ca, Na and Pb and by the plot of I/sub p//I/sub b/ ratio vs. concentration for Si, Fe, Ti, K, P, Cl, Cr, Mn, Ni, ...

Energy Technology Data Exchange (ETDEWEB)

A process is described for making a compound selected from a crystalline spinel of the formula A/sup II/V/sub 2-x//sup III/C/sub x//sup III/O/sub 4/ formula (1) or a crystalline perovskite of the formula D/sup III/V/sub 1-y//sup III/C/sub y//sup III/O/sub 3/ formula (2) from a pentavalent vanadium compound, where A is one or more of Mg, Zn, Mn, Fe, Co, Ni, Cu and Cd; D is one ore more of Y, the rare earths and Bi; C is one or more of Al, Ga, Cr, Fe and Co, x is zero to <2, and y is zero to<1. The process comprises (1) reducing a pentavalent vanadium oxidic compound to substantially the V/sup III/ state by heating at 100/sup 0/C. or less an aqueous medium slurry or solution of the pentavalent compound containing a reducing agent selected from hydrazine and a hydrocarbylhydrazine, (2) providing in the aqueous medium either before, during or after the reducing step, A/sup II/, D/sup III/ and C/sup III/ cations in solution in the ratio called ...

Energy Technology Data Exchange (ETDEWEB)

We report preliminary cross section covariances developed for the WPEC Subgroup 26 for 45 out of 52 requested materials. The covariances were produced in 15- and 187-group representations as follows: (1) 36 isotopes ({sup 16}O, {sup 19}F, {sup 23}Na, {sup 27}Al, {sup 28}Si, {sup 52}Cr, {sup 56,56}Fe, {sup 58}Ni, {sup 90,91,92,94}Zr, {sup 166,167,168,170}Er, {sup 206,207,208}Pb, {sup 209}Bi, {sup 233,234,236}U, {sup 237}Np, {sup 238,240,241,242}Pu, {sup 241,242m,243}Am, {sup 242,243,244,245}Cm) were evaluated using the BNL-LANL methodology. For the thermal region and the resolved and unresolved resonance regions, the methodology has been based on the Atlas-Kalman approach, in the fast neutron region the Empire-Kalman method has been used; (2) 6 isotopes ({sup 155,156,157,158,160}Gd and {sup 232}Th) were taken from ENDF/B-VII.0; and (3) 3 isotopes ({sup 1}H, {sup 238}U and {sup 239}Pu) were taken from JENDL-3.3. For 6 light nuclei ({sup 4}He, ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents the results of an experiment conducted in the BN-350 fast reactor in Kazakhstan that involved the irradiation of argon-pressurized thin-walled tubes (0--2000 MPa hoop stress) constructed from Fe-16Cr-15Ni-3Mo-Nb stabilized steel in contact with the sodium coolant, which enters the reactor at {approximately}270 C. Tubes in the annealed condition reached 75 dpa at 335 C, and another set in the 20% cold-worked condition reached 81 dpa at 360 C. Upon disassembly all tubes, except those in the stress-free condition, were found to have failed in an extremely brittle fashion. The stress-free tubes exhibited diameter changes that imply swelling levels ranging from 9 to 16%. It is expected that stress-enhancement of swelling induced even larger swelling levels in the stressed tubes. The embrittlement is explained in terms of the sensitivity of the swelling regime to displacement rate and the large, unprecedented levels of swelling ...

Energy Technology Data Exchange (ETDEWEB)

A transplant experiment was conducted to determine whether standard metabolic rate (SMR) of a freshwater shrimp (Palaeomonetes paludosus) would be affected by exposure to trace element-enriched coal combustion waste (coal ash). Shrimp were transplanted into replicate cages in a coal ash-polluted site and a reference site for 8 months. The coal ash-polluted site was characterized by elevated sediment concentrations of As, Cd, Cr, Cu, Ni, Pb and Se compared to sediments in the reference site. After 8 months in the study sites, shrimp in the polluted site appeared to have accumulated As, Cd and Se from the habitat, but there were on differences in survival between the study sites. However, mean SMR of shrimp (measured as O{sub 2} consumption at rest) held in the polluted site was 51% higher than mean SMR of shrimp held in the reference site. The elevation in SMR indicates that the energetic costs of maintenance are greater for shrimp chronically ...

Energy Technology Data Exchange (ETDEWEB)

Ophiolitic rocks occur as wall rocks of the 2.7 Ga Louis Lake batholith near Atlantic City, Wyoming. All of the Archean rocks are strongly deformed and metamorphosed to a greenschist and amphibolite facies, but relict structures and textures are commonly preserved. These include the following, from west to east: (1) metadiabase with rare coarse-grained metagabbro; (2) ultramafic rocks and metagabbro; (3) amphibolite, locally pillowed, overlain(.) by pelitic schist, banded iron formation, and quartzite; and (4) pillow lavas, massive sills or flows, and minor metasedimentary rocks. Slice 1 locally contains parallel dike margins and rare metagabbro screens; these features suggest that it may represent a sheeted dike complex. Slice 2 locally contains ultramafic rocks having relict cumulus textures and igneous layering, corresponding to the cumulus portion of an ophiolite. The pillow lavas of slice 4 and possibly slice 3 are interpreted as comprising the extrusive portion of the ophiolite. ...

International Nuclear Information System (INIS)

The results of investigation into a new series of Z-even nuclei - precursors of delayed protons (PDP) -"6"5Ge, "8"9Se, "9"3Kr, "8"1Zr, and "8"5Mo are presented. PDP were obtained by irradiation of targets in the following reactions: Zn(He, 2n) "6"5Ge, 22 MeV; "4"0Ca("3"2S, 2 pn) "1"9Se, 100 MeV; "6"0Ni ("1"60, 3 n), "7"3Kr, 75 MeV; "5"2Cr ("3"2S, 3n)"8"1Zr, 110 MeV; "5"6Fe("3"2S, 3n)"8"5Mo, 120 MeV. The targets (self-sustaining foils of thickness approximately 1.2 mg/cm"2) were placed at an angle of 15 deg to the direction of the ion beam. Upon irradiation targets were moved downwards into a measuring position. The spectra of protons, X and gamma-rays, and also the spectra of p - x, p-#gamma#, x - #gamma# coincidences accompanying the decay of "6"5Ge, "6"9Se,"7"3Kr and "8"1Zr, and "8"5Mo were measured. The measured half-lives are equal, to 31.5+-1.9, 27.3+-0.5, 28.5+-1.1, 6.3+-0.5, and 5.6 +-0.9 s respectively. The experimental spectra are ...

International Nuclear Information System (INIS)

Focused ion beam (FIB) microscopes have become well-established in the semiconductor industry during the past decade, and are rapidly gaining attention in the field of materials science, both as a tool for producing site specific, parallel sided transmission electron microscope (TEM) specimens and as stand alone specimen preparation and imaging systems. FIB secondary electron imaging (SEI) of nickel-based alloys, such as commercially produced Alloy 600 (approximately Ni 15Cr 10Fe 0.5C), has been demonstrated to show a high degree of sensitivity to the presence of deformation in the alloy, and FIB secondary ion imaging (SII) is particularly useful for identifying the presence of grain boundary corrosion, as secondary ion yields from metallic specimens can increase by three orders of magnitude in the presence of oxygen. This 'oxygen enhanced yield', makes FIB SII ideal for detection of corrosion at grain boundaries down to thicknesses of only a ...

International Nuclear Information System (INIS)

Composite particles represented as TiV_2_._1Ni_0_._3-Raney Ni(R) were prepared by ball-milling a TiV_2_._1Ni_0_._3 alloy with Raney Ni in the presence of 0.01 M sodium hypophosphite (NaH_2PO_2) aqueous solution as a reducing agent. The composite particles had different morphology from original TiV_2_._1Ni_0_._3 alloy particles and TiV_2_._1Ni_0_._3-Raney Ni composite particles prepared by the ball-milling in the absence of the NaH_2PO_2 aqueous solution. In charge-discharge cycle tests, the TiV_2_._1Ni_0_._3-Raney Ni(R) composite electrode showed the maximum discharge capacity of 620 mAh g"-"1, while its cycle durability was similar to the TiV_2_._1Ni_0_._3 alloy electrode, which was explained from depth profiles of constituent elements by Auger electron spectroscopy (AES). In ...

Energy Technology Data Exchange (ETDEWEB)

There is an increasing number of applications for hard coatings in engineering where the properties of the single-layer coating are not sufficient. One way to solve this problem is to use a multilayer coating that combines the properties of several coating materials. In this study, TiN-CrAlN and CrN-CrAlN multilayer coatings were deposited on 100Cr6 and S6-5-2 (DIN) steel substrates, by means of unbalanced magnetron sputtering. For comparison, TiN, CrN and CrAlN single-layer coatings were also prepared. For all depositions the coating temperature was below 473 K. Indentation testing, hardness measurements and scratch tests were performed to characterize the mechanical properties. The correlation between the wear behavior in rolling contact and the mechanical properties of the multilayer coatings is reported. A ball crater preparation technique through scratch tests and wear tracks ...

International Nuclear Information System (INIS)

In this study, the corrosion behavior of commercially pure titanium (c.p. Ti), Ti-6Al-4V and five new experimental Ti-Cr alloys was evaluated through open-circuit potential (OCP) and potentiodynamic polarization measurement in an artificial saliva containing fluoride. Electron spectroscopy for chemical analysis (ESCA) was used to characterize the composition of the passive films on the alloy after potentiodynamic polarization measurement. It was found that in standard artificial saliva the OCP increases with higher Cr content in Ti-Cr alloys. In 0.5% NaF artificial saliva, the OCP decreases with decreasing Cr in Ti-Cr alloys, and all but Ti-5Cr remain consistently higher than those of c.p Ti and Ti-6Al-4V. Linear polarization results show that artificial saliva and artificial saliva containing 0.5% NaF result in different corrosion behavior in ...

International Nuclear Information System (INIS)

Nano indentation analysis and transmission electron microscopy observation were performed to investigate a microstructural evolution and its influence on the hardening behavior in Fe-Cr alloys after an irradiation with 8 MeV Fe4+ ions at room temperature. Nano indentation analysis shows that an irradiation induced hardening is generated more considerably in the Fe-15Cr alloy than in the Fe-5Cr alloy by the ion irradiation. TEM observation reveals a significant population of the a0 dislocation loops in the Fe-15Cr alloy and an agglomeration of the 1/2a0 dislocation loops in the Fe-5Cr alloy. The results indicate that the a0 dislocation loops will act as stronger obstacles to a dislocation motion than 1/2a0 dislocation loops.

Energy Technology Data Exchange (ETDEWEB)

We present a study of the crystal field in PrNiAl, NdNiAl, ErNiAl and ErCuAl intermetallic compounds based on inelastic neutron spectroscopy. These compounds crystallize in the ZrNiAl-type hexagonal structure with an orthorhombic symmetry on rare-earth sites. The results are compared with the specific-heat data, and the lower parts of the crystal-field energy-level schemes are determined. (orig.)

British Library Electronic Table of Contents (United Kingdom)

In the paper, the effect of Ni content, WC grain size and Mo2C addition on WC-6.25wt%TiC-9.3wt%Ni cemented carbide were investigated to improve the properties of Ni-bonded cemented carbides. The results show that the decrease of Ni content will result in the decrease of transverse rupture strength and increase of hardness; with the decrease of WC particle size, hardness increases due to the refinement of WC grains, however, the transverse rupture strength decrease due to the decrease of Ni binder thickness; Mo2C proves to be an effective grain growth inhibitor. With the increase of Mo2C content, the WC grains are refined and the hardness and transverse rupture strength are improved. Generally, when the Ni content is decreased to 8.4wt%, 13.45mm WC is used and 1.2wt% Mo2C is added, a higher...

British Library Electronic Table of Contents (United Kingdom)

Ni-Co/SiC nanocomposite coatings were electrodeposited in a modified watt type of Ni-Co bath containing 20nm SiC particles to be codeposited. Potentiodynamic polarization tests were conducted to study the effect of the SiC particulates on the electrodeposition of Ni and Co. Scanning electron microscopy was used to assess the morphology of the Ni-Co alloy and Ni-Co/SiC nanocomposite coatings. The distribution of the particulates in the matrix was considered by means of transmission electron microscopy. Applying nanomechanical testing instruments coupled to atomic force microscopy, mechanical properties of the alloy and composite coatings were studied and compared. The presence of 11vol.% SiC in the Ni-Co matrix increased hardness more than 60%. The average depth of scratch in the mentioned ...

International Nuclear Information System (INIS)

Si/Ni alloy and graphite composites were synthesized using arc-melting followed by high energy mechanical milling (HEMM). Alloy particles comprising of NiSi2, NiSi and Si phases were distributed finely and uniformly on the surface of graphite in the composites obtained after Hem. The composite containing 60 wt.% of Si/Ni alloy exhibited a stable capacity of ?780 mAh/g. Fourier transform infrared spectroscopy (FTIR) analysis confirmed that some bonds were formed between alloy and graphite after HEMM, which appeared to retain the electrical connection between alloy and graphite during cycling. X-ray diffraction (XRD) analysis indicated that NiSi2 and NiSi phases, which acted as an inactive alloy matrix remained invariant during charge and discharge. In addition to NiSi2 and NiSi phases, disordered graphite layers also ...

International Nuclear Information System (INIS)

K#beta#-to-K#alpha# X-ray intensity ratios of Ti, Cr, Fe and Co in pure metals and in Cr_0_._2_6Fe_0_._7_4, Cr_0_._8_0Co_0_._2_0 and Ti_0_._8_0Cr_0_._2_0 alloys have been measured following excitation by 59.54 keV #gamma#-rays from a 7400 MBq (200 mCi) "2"4"1Am point-source. The valence electronic structure of Ti, Cr, Fe and Co in the samples have been evaluated by the comparison of the measured K#beta#-to-K#alpha# intensity ratios with the results of multiconfiguration Dirac-Fock calculations performed for various electronic configurations of these metals. The 3d-electron populations obtained for pure metallic Ti, Cr, Fe and Co agree well with the results of band structure calculations of Papaconstantopoulos (Handbook of band structure of elemental solids, Plenum Press, New York, 1986). Our analysis indicates significant increase of 3d-electron population of ...

CERN Document Server

beta- and gamma-decay studies of neutron-rich chromium, manganese, cobalt and nickel isotopes including the new isotopes $^{60}$Cr and $^{60g}$Mn

Energy Technology Data Exchange (ETDEWEB)

Short communication

Science.gov (United States)

We report on the results of a preliminary study of the GCR-induced photon luminescence of the Moon

International Nuclear Information System (INIS)

Lead lanthanum zirconate titanate (PLZT) nanopowders with chemical compositions x/65/35 PLZT (x = 6 - 10 mol%) were prepared by sol-gel method. PLZT ceramics was obtained by the conventional sintering method and utilizing the hot pressing method. The investigations of dielectric and ferroelectric measurements of as obtained PLZT ceramics have revealed the influence of lanthanum concentration on the properties of PLZT electroceramics. (author)

Energy Technology Data Exchange (ETDEWEB)

Six intermetallic alloys (CeNi/sub 5/, MmNi/sub 5/, Ca/sub 0/ /sub 2/(Ce/sub 0/ /sub 65/Mm/sub 0/ /sub 35/)/sub 0/ /sub 8/Ni/sub 5/, Ca/sub 0/ /sub 2/Ce/sub 0/ /sub 8/Ni/sub 5/, Ca/sub 0/ /sub 2/Mm/sub 0/ /sub 8/Ni/sub 5/, and a mixed alloy, CeNi/sub 5//MmNi/sub 5/) were investigated with respect to their suitability to provide high hydrogen capacity and their potential for use in providing substantial hydrogen pressure at both low and high temperatures. A second phase of our investigation dealt with ball-milling and hydriding and dehydriding cycles to produce fine particles for use in hydride powder transfer studies. A summary of several Van't Hoff plots is also included for hydride-forming alloys.

International Nuclear Information System (INIS)

Fe-Cr amorphous films have been formed by both in situ evaporation of multilayered films and ion beam mixing in a target chamber of a 200 keV implanter. The effects of Cr content and ion irradiation on the amorphization of films were examined by transmission electron microscope (TEM). Corrosion of film was investigated by means of a potential dynamic polarization. Corrosion resistance of amorphous film in 0.5 mol H-2SO-4 solution is considerably increased than that of pure iron. Using X ray photoelectron spectroscopy (XPS) corrosion resistance in atmosphere of amorphous Fe-Cr passive films formed by P"+ mixing was studied. Results show that the richness of Cr and P exist at the surface of Fe-Cr film.

Energy Technology Data Exchange (ETDEWEB)

Adsorption by activated red mud (ARM) is investigated as a possible alternative to the conventional methods of Cr(VI) removal from aqueous synthetic solutions and industrial effluents. Adsorption characteristics suggest the heterogenous nature of the adsorbent surface sites with respect to the energy of adsorption. Various factors such as pH, contact time, Cr(VI) concentration, amount of adsorbent, and temperature are taken into account, and promising results are obtained. The applicability of the Langmuir as well as Freundlich adsorption isotherms for the present system is tested. The loading factor (i.e., milligrams Cr(VI) adsorbed per gram of ARM) increased with initial Cr(VI) concentration, whereas a negative trend was observed with increasing temperature. The influence of the addition of anions on the adsorption of Cr(VI) depends on the relative affinity of the anions for the ...

Energy Technology Data Exchange (ETDEWEB)

LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} was prepared through a solid-state reaction using various Ni precursors. The effect of precursors on the electrochemical performance of LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} was investigated. LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} made from Ni(NO{sub 3}){sub 2}.6H{sub 2}O shows the best charge-discharge performance. The reversible capacity of LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} is about 145 mAh g{sup -1} and remained 143 mAh g{sup -1} after 10 cycles at 3.0-5.0 V. The XRD results showed that the precursors and the dispersion methods had significant effect on their phase purity. Pure spinel phase can be obtained with high energy ball-milling method and Ni(NO{sub 3}){sub 2}.6H{sub 2}O as precursor. Trace amount of NiO and Li{sub 2}MnO{sub 3} phase were detected in LiNi{sub 0.5}Mn{sub ...

Energy Technology Data Exchange (ETDEWEB)

The high temperature solid-state reaction between LiNiO{sub 2} and V{sub 2}O{sub 3} (or V{sub 2}O{sub 5}) in air used to prepare LiNiVO{sub 4} has been further studied. This quaternary Li-Ni-V-O reaction is strongly dependent on reaction temperature and lithium stoichiometry in Li{sub x}Ni{sub 2-x}O{sub 2} and has produced a highly crystalline LiNiVO{sub 4} material whose structure has been confirmed to be an inverse spinel by Rietveld analysis with a Bragg R-factor of 1.18 in the absence of crystal orientation preference. The cell performance of LiNiVO{sub 4} prepared at various temperatures or by varying x-values in Li{sub x}Ni{sub 2-x}O{sub 2} has been examined in lithium coin cells and indicated that preparation at low temperatures or when x=0.89 provided an electrode material with higher cell capacity. (orig.)

British Library Electronic Table of Contents (United Kingdom)

A Ni3Al coating was prepared by plasma spraying technique on the surface of titanium alloy. Ni-Al mixed powders, coatings and reaction products were investigated by scanning electron microscope, EDS, DSC and XRD. A tight bonding between the coating and the substrate was formed. The X-ray diffraction analysis of the patterns showed that the coating not only had Ni3Al phase, but also had NiO and Al2O3 phase microcontent. Comparing Ni coated Al to Ni3Al at 900^oC, the diffusion was stronger and the diffusion layer was thicker. A minute pore structure was formed at 1200^oC in the front edge of solid-state reaction layer. So Ni3Al restrained the solid-state reaction of the coating with the substrate, and as a whole weakened the entry of oxygen atoms into the substrate and quenched the out-diffu...

Energy Technology Data Exchange (ETDEWEB)

Abstract not provided

Science.gov (United States)

... without the problem of purple plague. The Au-Ni-In evaporated ... surface and bonding degradation (purple plague) St step-stress ...

Science.gov (United States)

... 9. Delay Circuits ----- N9-i 10. Main Gate Multivibrators ----- NI0-I 11. ...

British Library Electronic Table of Contents (United Kingdom)

In this paper we describe a Ni-Sn intermetallic material obtained via template electroplating synthesis. The structure and the morphology of this material are investigated by X ray diffraction (XRD) and Scanning Electron Microscopy (SEM) analyses. We demonstrate that Ni-Sn behaves as a sub-micrometric electrode showing a favourable response when cycled in a lithium cell. The results here reported suggest that the template electroplating is a promising synthetic approach that can lead to an optimized structure and morphology of the Ni-Sn electrode, such as to confer it a role of a high capacity anode in advanced lithium ion batteries.

Science.gov (United States)

Resistivity measurements were performed on Fe40 Ni40 B20 and Pd80 Si20 in order to improve the understanding of structural relaxation in amorphous metals. A model describing structural relaxation as a combination of chemical short range ordering (CSRO) an...

Energy Technology Data Exchange (ETDEWEB)

The ErNi{sub 1-} {sub x} Cu {sub x} Al compounds crystallize all in the hexagonal ZrNiAl-type structure. The concentration dependence of lattice constants shows a discontinuity between x=0.5 and 0.6. This structural change has no primary impact on the magnetic order in this series, but influences the crystal field. The lower part of the crystal-field energy-level schemes has been estimated from the specific-heat data.

International Nuclear Information System (INIS)

The Ni(H_2O)_6 ion is located at an inversion center. Six octahedral water molecules surround the Ni"I"I ion and form hydrogen bonds with the sulfate groups. Each ammonium group binds to the sulfate groups through hydrogen bonds. (orig.).

British Library Electronic Table of Contents (United Kingdom)

The present study was aimed at investigating effects of nickel (NiCl2) on secretion of testosterone (T), cell viability, ultrastructure and apoptosis in mouse Leydig cells. Testosterone release was measured after 48h of culture with 15.67, 31.25, 62.5, 125, 250, 500 and 1000mmol/L NiCl2 or without NiCl2 using radioimmunoassay. Cell viability was assessed by a MTT (metabolic activity assay). Quantification of apoptotic cells was performed using TUNEL assay and the ultrastructural changes were analyzed using transmission electron microscopy. The viability was decreased after addition of >=250mmol/L NiCl2. A concentration-dependent depression of T production was observed. The percentage of apoptotic cells was significantly increased only after addition of 125, 250 and 1000mmol/L NiCl2. After ...

Energy Technology Data Exchange (ETDEWEB)

In a recent publication [I. Galanakis, K. Ozdog-tilde an, E. Sasiog-tilde lu, B. Aktas, Phys. Rev. B 74 (2006) 140408(R)] we have shown that in the case of CrAs and related transition-metal chalcogenides and pnictides, crystallizing in the zinc-blende structure, the excess of the transition-metal atoms leads to half-metallic ferrimagnetism. The latter property is crucial for spintronic applications with respect to ferromagnets due to the lower stray fields created by these materials. We extend this study to cover the case where the transition-metal atoms sitting at antisites are not identical to the ones in the perfect sites. In Cr-based compounds, the creation of Mn antisites keeps the half-metallic ferrimagnetic character produced also by the Cr antisites. In the case of VAs, Cr and Mn antisites keep the half-metallic character of VAs (contrary to V antisites) due to the larger exchange splitting ...

Energy Technology Data Exchange (ETDEWEB)

Substantial roles of precipitates such as Zr-Fe-Cr type intermetallic compounds on uniform corrosion and hydrogen pickup of zirconium alloys in pure water autoclave tests were investigated from an electrochemical point of view. This paper describes the roles on corrosion. A corrosion test on precipitate-containing and precipitate-free materials made from pure zirconium and a small quantity of iron and chromium, rest potential measurements on an intermetallic compound of Zr(FeCr){sub 2} and zirconium matrix, and a galvanic coupling test of those were performed. Results showed that corrosion behavior of zirconium alloys could be attributed to the electrochemical properties of intermetallic compounds precipitated in each alloy. Namely, the cathodic and anodic polarization characteristics were associated with anodic protection provided by the precipitates on the alloys and the precipitates degradation in the oxide films, respectively. The mechanism ...

International Nuclear Information System (INIS)

The status of development and commercialization of a modified 9 Cr-1 Mo alloy is presented. The alloy is modified by the addition of 0.06 to 0.10% Nb and 0.18 to 0.25% V. The alloy is recommended for use in the normalized and tempered condition (1040"0C for 1 h, air cooled to room temperature; 760"0C for 1 h, air cooled to room temperature). Heat treatment, Charpy impact, tensile, and creep properties of the alloy are described in detail along with a brief description of other properties. The modified alloy has creep strength that exceeds that of standard 9 Cr-1 Mo and 2 1/4 Cr-1 Mo steels for the temperature range from 427 to 704"0C. The total-elongation and reduction-of-area values for all test temperatures and rupture times up to 22,500 h exceed 15 and 70%, respectively. The estimated design allowable stresses for this alloy are higher than those for standard 9 Cr-1 Mo and 2 1/4 ...

Energy Technology Data Exchange (ETDEWEB)

The production of hydrogen from the two-stage pyrolysis-gasification of polypropylene using a Ni/CeO{sub 2}/ZSM-5 catalyst has been investigated. Experiments were conducted on CeO{sub 2} loading, calcination temperature and Ni loading of the Ni/CeO{sub 2}/ZSM-5 catalyst in relation to hydrogen production. The results indicated that with increasing CeO{sub 2} loading from 5 to 30 wt.% for the 10 wt.% Ni/CeO{sub 2}/ZSM-5 catalyst calcined at 750 C, hydrogen concentration in the gas product and the theoretical potential hydrogen production were decreased from 63.0 to 49.8 vol.% and 50.4 to 21.6 wt.%, respectively. In addition, the amount of coke deposited on the catalyst was reduced from 9.5 to 6.2 wt.%. The calcination temperature had little influence on hydrogen production for the catalyst containing 5 wt.% of CeO{sub 2}. However, for the 10 wt.% Ni/CeO{sub 2}/ZSM-5 catalyst with a ...

Energy Technology Data Exchange (ETDEWEB)

Excessive irradiation due to unexpected leakage was found on a patient receiving electron beam therapy. The cause of this leakage was analyzed and the amount of leakage was measured for different electron beam energies. The highest leakage occurred with a 6 x 6 cm cone using a 12 MeV electron beam. The leakage dose measured along the side of the cone could be as great as 40%. Until the cones are modified or redesigned, it is advised that all patient setups be carefully reviewed to assure that no significant patient areas are in the side scatter region.

International Nuclear Information System (INIS)

The occurrence of stable decagonal quasicrystalline phase in Al-Co-Ni and Al-Cu-Co alloys through conventional solidification is well established. Earlier, we have studied the effect of Cu substitution in place of Co in the Al_7_0Co_1_5Ni_1_5 alloy. Here we report the structural/micro-structural changes with substitution of Cu for Ni in rapidly solidified Al-Co-Ni alloys. The melt spun ribbons have been characterized using X-ray diffractometry, scanning and transmission electron microscopy. With an increase in Cu content in the melt spun Al_7_0Co_1_5Cu _xNi_1_5_-_x (x = 0-15 at.%) alloys, the relative amount of the decagonal phase decreased up to 10 at.% of Cu. At this composition, the quaternary alloy showed the co-existence of decagonal quasicrystal and superstructure of #tau#_3 vacancy ordered crystalline phases. The decagonal phase containing Cu showed more disordering than ...

International Nuclear Information System (INIS)

64Cu (T1/2=12.7h, ?- decay: 40%, ?+ decay: 19%, E.C. decay: 41%) is one of the most useful radioisotope in the nuclear medicine due to its multiple decay mode and the intermediate half-life. Several nuclear reaction, i.e., 64Ni(p,n)64Cu, 68Zn(p,?n)64Cu and 64Ni(d,2n)64Cu have been investigated for production. The highest could be obtained with proton irradiation on the enriched 64Ni target. For mass and routine production, the 64Ni target fabrication using electroplating, the reliable chemical separation of 64Cu from the irradiated 64Ni target and the effective recovery process for the recycling of very expensive enriched material ($20,000/g) and so forth are absolutely necessary to be established. In this work, we report our mass production method of 64Cu with 64Ni and Cyclone-30 accelerator

Science.gov (United States)

The purpose of this communication is to determine whether the solubility enhancements for cold-worked Pd-Ni alloys increase or decrease with atom fraction of Ni. Substitutional Ni atoms contract and Pd lattice, in contrast to the lattice expansion resulting from substitutional Ag in Pd. The Pd-Ni alloy system forms a continuous series of fcc solid solution alloys over the whole composition range. The solubility enhancements will also be determined for a series of homogeneous, ternary Pd[sub 1[minus]x]Ni[sub 1/2x]Ag[sub 1/2x] alloys for x in the range from 0 to 0.2. For this series of ternary alloys the fcc lattice parameters do not change significantly from that of pure Pd. The alloys used in this research were purchased from Tanaka Kikinzoku Kogyo K.K. The detailed experimental procedure has been described previously. The alloys were all deformed by cold-rolling ca 90%. Both the ...

Energy Technology Data Exchange (ETDEWEB)

This study compares the microstructure and mechanical properties of plain and 0.9 or 3.6 wt% VC- or Cr{sub 3}C{sub 2}-doped WC-12 wt% Co hardmetals with 40 wt% NbC, prepared by pulsed electric current sintering (PECS) in the solid state for 4 min at 1240 deg. C and conventional pressureless liquid phase sintering (CS) for 1 h at 1420 deg. C. The addition of VC or Cr{sub 3}C{sub 2} was found to inhibit grain growth of the residual WC grains, whereas the size of the solid solution (Nb,W,V/Cr)C grains was hardly influenced. The type of grain growth inhibitor and densification temperature however, strongly influenced the composition of the NbC solid solution formed, which was thermodynamically and experimentally assessed.

British Library Electronic Table of Contents (United Kingdom)

The corrosion behavior of hard metals with VC and Cr3C2 grain growth inhibitors was investigated in alkaline solutions by electrochemical methods. The two inhibitors have opposite effects on the corrosion behavior: Cr3C2 significantly improves the corrosion behavior, whereas VC-containing alloys show a poor resistance. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) and analytical transmission electron microscopy (TEM) analyses of the distributions of Cr and V in the composite material, as well as in the surface layers formed during corrosion were employed to clarify the influence of these elements on the corrosion behavior. The measurements showed that VC is precipitated mostly along the WC/binder interface after the liquid-phase sintering process, while Cr3C2 is almost homogene...

Science.gov (United States)

The formation of palladium silicides near the interface may decrease hydrogen solubility at the effective metal/semiconductor ...

Energy Technology Data Exchange (ETDEWEB)

Phosphate/chromate and accelerated chromate coatings were produced on commercially available aluminium. The Cr, P and Fe components of the conversion coatings were determined by radioactive tracer technique. The tracer technique was combined with ion-exchange and film-sectioning methods to determine the chromium(III)/total chromium ratio in the accelerated chromate coating. It was found that during the acidic dissolution of the conversion coating the chromium(III)/total chromium ratio may suffer changes. The film-forming components in the metal/bath interface are supersaturated and deposited onto the aluminium. The identified components of the accelerated chromate coatings are Cr(OH)sub(3), Cr(OH)CrOsub(4) and Crsub(4)(Fe(CN)sub(6))sub(3) and the chromium(III)/total chromium ratio was found to be cca. 2/3. (author). 11 refs.; 5 figs.

CERN Document Server

We report a new tetragonal ground-state for perovskite-structured PbCrO3 from DFT+U calculations, and explain its anomalously large volume. The new structure is stabilized due to orbital ordering of Cr-d in the presence of a large tetragonal crystal field, mainly due to off-centering of the Pb atom. At higher pressures (smaller volumes) there is a first-order transition to a cubic phase where the Cr-d orbitals are orbitally liquid. This phase-transition is accompanied by a ~11.5% volume collapse, one of the largest known for transition-metal oxides. The large ferroelasticity and its strong coupling to the orbital degrees of freedom could be exploited to form potentially useful magnetostrictive materials

International Nuclear Information System (INIS)

1972. United States Narayanan, GH Archbold, TF Univ. of California Press.;

Science.gov (United States)

... 7 Page 11. Figure 5. Diffraction pattern shown a and ~ slip directions with the associated misalignment for single colonies of Ti6242 [2]. 8 Page 12. -- ...

Science.gov (United States)

... Stone, CR & Grover, CC Practice Readers ... Tolbert, M., Withers, S. & Watkins, HT, Good Workers All State Department of Education, Columbia, South ...