Energy Technology Data Exchange (ETDEWEB)

Phenanthrene and naphthalene sorption isotherms were measured for three different series of kerogen materials using completely mixed batch reactors. Sorption isotherms were nonlinear for each sorbate-sorbent system, and the Freundlich isotherm equation fit the sorption data well. The Freundlich isotherm linearity parameter n ranged from 0.192 to 0.729 for phenanthrene and from 0.389 to 0.731 for naphthalene. The n values correlated linearly with rigidity and aromaticity of the kerogen matrix, but the single-point, organic carbon-normalized distribution coefficients varied dramatically among the tested sorbents. A dual-mode sorption equation consisting of a linear partitioning domain and a Langmuir adsorption domain adequately quantified the overall sorption equilibrium for each sorbent-sorbate ...

British Library Electronic Table of Contents (United Kingdom)

The potential of waste seashells powder, as a new adsorbent for Brilliant Red HE-3B reactive dye removal from aqueous solutions, was examined by the batch technique. The Freundlich, Langmuir, and Dubinin-Radushkevich adsorption models were applied to describe the equilibrium sorption data and to determine the corresponding isotherm constants. The values of the thermodynamic parameters, ?G, ?H, and ?S, indicate that the sorption of reactive dye is a spontaneous and endothermic process. The kinetic data evaluated by pseudo-first order, pseudo-second order, and intraparticle diffusion kinetic models suggested that the sorption of reactive dye onto seashell is a complex process and both surface sorption and intraparticle diffusion contributes to the rate limiting step.

British Library Electronic Table of Contents (United Kingdom)

The lignin, one of the main by-products of the pulp industry, can be used to remove dyes from textile wastewaters. The potential of the lignin for Brilliant Red HE-3B reactive dye removal from aqueous solutions at pH=1.5 was examined by the batch technique as a function of dye concentration, solution temperature and contact time. The Freundlich, Langmuir, Dubinin-Radushkevich and Tempkin adsorption isotherms were used to describe the data of sorption equilibrium and to determine its corresponding isotherm constants. The thermodynamic parameters DG, DH and DS were also determined; the obtained values show that the sorption of reactive dye on lignin is a spontaneous, endothermic and entropy-driven process. The kinetic of reactive dye sorption was analyzed using the pseudo-first order and pse...

Science.gov (United States)

The identification and characterization of carbonaceous materials (CMs) that control hydrophobic organic chemical (HOC) sorption is essential to predict the fate and transport of HOCs in soils and sediments. The objectives of this paper are to determine the types of CMs that control HOC sorption in the oxidized and reduced zones of a glacially deposited groundwater sediment in central Illinois, with a special emphasis on the roles of kerogen and black carbon. After collection, the sediments were treated to obtain fractions of the sediment samples enriched in different types of CMs (e.g., humic acid, kerogen, black carbon), and selected fractions were subject to quantitative petrographic analysis. The original sediments and their enrichment fractions were evaluated for their ability to sorb trichloroethene (TCE), a common groundwater pollutant. Isotherm results and mass fractions of CM enrichments were used to calculate ...

Energy Technology Data Exchange (ETDEWEB)

Phosphorus sorption capacities of several different materials including Merribrook soil (a loamy sand) and some industrial solid wastes (red mud neutralized with gypsum, fly ash, bottom ash and black oxide) were determined in sorption isotherms by Langmuir and Freundlich equations. The materials were characterized by bulk density, particle density, total porosity and particle size distributions. Red mud gypsum possessed the best sorption capacity based on the Langmuir maxima. Alkaline fly ash and Merribrook soil had lower sorption maxima compared to the red mud gypsum. Bottom ash and acidic fly ash had very low sorption capacity at low concentrations. Merribrook soil had the highest hydraulic conductivity. The results suggested that alkaline fly ash may be a promising amendment for coarse sand bed to enhance phosphorus removal. Merribrook soil appears to be ...

International Nuclear Information System (INIS)

An efficient adsorption process is developed for the decontamination of trivalent chromium from tannery effluents. A low cost activated carbon (ATFAC) was prepared from coconut shell fibers (an agricultural waste), characterized and utilized for Cr(III) removal from water/wastewater. A commercially available activated carbon fabric cloth (ACF) was also studied for comparative evaluation. All the equilibrium and kinetic studies were conducted at different temperatures, particle size, pHs, and adsorbent doses in batch mode. The Langmuir and Freundlich isotherm models were applied. The Langmuir model best fit the equilibrium isotherm data. The maximum adsorption capacities of ATFAC and ACF at 25 deg. C are 12.2 and 39.56 mg/g, respectively. Cr(III) adsorption increased with an increase in temperature (10 deg. C: ATFAC-10.97 mg/g, ACF-36.05 mg/g; 40 deg. C: ATFAC-16.10 mg/g, ACF-40.29 mg/g). The kinetic studies were conducted ...

International Nuclear Information System (INIS)

The adsorptive removal of boron from aqueous solution by using the neutralized red mud was studied in batch equilibration technique. The effects of pH, adsorbent dosage, initial boron concentration and contact time on the adsorption were investigated. The experiments demonstrated that boron removal was of a little fluctuation in pH range of 2-7 and it takes 20 min to attain equilibrium. The adsorption data was analyzed using the Langmuir and the Freundlich isotherm models and it was found that the Freundlich isotherm model represented the measured sorption data well.

Energy Technology Data Exchange (ETDEWEB)

An evaluation was made of the effectiveness of the action of reagents used for cleaning cyan-containing waste water for conditioning of the overflow of copper concentrate thickners of the Belousovskiy enrichment before sorption extraction of gold by activated charcoal. It was established that conditioning of the overflow by iron sulfates (II), copper and zinc diminshes, and by hypochlorite increases the capacitance of the activated charcoal for gold.

British Library Electronic Table of Contents (United Kingdom)

This study examined kinetics and mass transfer in the biosorption of heavy metals onto Caulerpa lentillifera. The sorption capacity of Cu^2^+, Pb^2^+ and Cd^2^+ from aqueous solution increased with initial metal concentration and decreased with biosorbent dose. Kinetic data were well described using the pseudo-second-order model. Results showed that both external mass transfer and intraparticle diffusion were rate limiting steps in the biosorption process. Activation energy of biosorption kinetics fell in the range of 3-13kJ/mol. The biosorption of Cu^2^+, Cd^2^+ and Pb^2^+ on the biomass correlated well with the Langmuir isotherm (R^2>0.99) with maximum sorption capacities at 293K of 0.169, 0.085 and 0.177mol/kg for Cu^2^+, Cd^2^+ and Pb^2^+ ions, respectively. Thermodynamic studies demon...

Energy Technology Data Exchange (ETDEWEB)

The biosorption of Cu(II) from aqueous solutions by valonia tannin resin was investigated as a function of particle size, initial pH, contact time and initial metal ion concentration. The aim of this study was to understand the mechanisms that govern copper removal and find a suitable equilibrium isotherm and kinetic model for the copper removal in a batch reactor. The experimental isotherm data were analysed using the Langmuir, Freundlich and Temkin equations. The equilibrium data fit well in the Langmuir isotherm. The experimental data were analysed using four sorption kinetic models - the pseudo-first- and second-order equations, the Elovich and the intraparticle diffusion model equation - to determine the best fit equation for the biosorption of copper ions onto valonia tannin resin. Results show that the pseudo-second-order equation provides the best correlation for the biosorption process, whereas ...

British Library Electronic Table of Contents (United Kingdom)

In preparation for studying the hydrolytic degradation of Estane 5703 in the plastic-bonded explosive PBX 9501, the sorption (solubility) and diffusion of water in PBX 9501 and each of its components are studied experimentally and modeled theoretically. Experiments are reported that measure the weight gain or loss due to a change in the relative humidity (RH). For all of the components, the equilibrium amount of water sorbed per gram of sample is linear in the RH at low relative humidities but curves upwards at higher relative humidities. This behavior is modeled with a water cluster model. Diffusion coefficients are determined by modeling the time dependence of the water concentrations assuming Fickian diffusion, and that fits the data for some of the materials. However, all the samples t...

British Library Electronic Table of Contents (United Kingdom)

This paper explores the through-/in-plane characteristics of water transport in the cathode gas diffusion layer (GDL) of a polymer electrolyte fuel cell (PEFC). Theoretical analysis is performed on the non-isothermal two-phase flow under flow channels. A dimensionless group Da (Damkohler number for PEFC operation), defined as the ratio of water generation rate to water vapor-phase removal rate, is formulated to characterize the flow regimes in a PEFC. This group, lumping geometrical parameters and physical properties, compares the water vapor-phase removal capability (via water diffusion and holding capacity) with the rate of water production by the oxygen reduction reaction. We find that this dimensionless group can be used to characterize the non-isothermal, two-phase phenomena: when Da&...

International Nuclear Information System (INIS)

Because of the environmental hazard of organic solvents such as chlorinated or aromatic hydrocarbons, water soluble and biodegradable substitutes have come into use. It should be assessed how they affect soil and aquifer when spilled in leaks or accidents. This was simulated in a model system using methanol and percolation columns, one filled with material from the unsaturated subsurface and two with different materials from aquifers. The results reveal that a spill of the substitutes can also cause problems. In homogeneous soils and at long retention times until the substance reaches the aquifer, sorption and biological degradation are most likely to prevent contamination of the groundwater. When oxygen supply in the subsurface is insufficient, reducing conditions occur and sulphide is formed. The data show that much more methanol was eliminated than reflected by the consumption of electron acceptors. This indicates that ...

International Nuclear Information System (INIS)

In this work, a water-soluble polymer, polyethylenimine (PEI) was used for the simultaneous separation and preconcentration of trace Cu and Mn prior to their determination by flame atomic absorption spectrometry. For this purpose, the sample and the PEI solution were mixed and the metal-bound polymer was precipitated by adding acetone. The precipitate was separated and dissolved in a minimum amounts of water and aspirated into a flame AAS. By increasing the ratio of the volumes of sample to water used in dissolving the precipitate, the analyte elements were concentrated as needed. The sorption is quantitative in the pH ?6. Detection limits were 5.2 ?g/L for Cu and 5.4 ?g/L for Mn. This method is simple, fast and precise.

British Library Electronic Table of Contents (United Kingdom)

Biosorption of lead(II) ions from aqueous solution onto the seed husk of Calophyllum inophyllum was investigated in a batch system. Equilibrium, thermodynamics and kinetic studies were conducted by considering the effects of pH, initial metal ion concentration, contact time, and temperature. The results showed that the uptake of the metal ions increased with increase in initial metal ion concentration. The pH for optimum adsorption was 4 for the Pb(II) ions (q=4.86mg/g and 97.2% adsorption). Langmuir isotherm described the biosorption of Pb(II) ions onto the biomass (R^2=0.9531) better than the Freundlich model (R^2=0.7984), and the Temkin model (R^2=0.8761). Biosorption kinetics data obtained for the metal ions sorption were fitted using pseudo-first-order and pseudo-second-order. It was ...

CERN Document Server

This work investigates the impingement of a liquid microdroplet onto a glass substrate at different temperatures. A finite-element model is applied to simulate the transient fluid dynamics and heat transfer during the process. Results for impingement under both isothermal and non-isothermal conditions are presented for four liquids: isopropanol, water, dielectric fluid (FC-72) and eutectic tin-lead solder (63Sn-37Pb). The objective of the work is to select liquids for a combined numerical and experimental study involving a high resolution, laser-based interfacial temperature measurement to measure interfacial heat transfer during microdroplet deposition. Applications include spray cooling, micro-manufacturing and coating processes, and electronics packaging. The initial droplet diameter and impact velocity are 80 {\\mu}m and 5 m/s, respectively. For isothermal impact, our simulations with ...

Science.gov (United States)

... TITLE (Include Security Classification) Sorption of Selected Volatile Organic Constituents of Jet Fuels and Solvents on Natural Sorbents from Gas ...

Energy Technology Data Exchange (ETDEWEB)

Biosorption of heavy metals by various biological materials has been studied extensively in the last decade due to its potential particularly in wastewater treatment. The presence of a large number of metals in industrial metal-bearing solutions makes it necessary to investigate their effect on the final metal uptake by individual biosorbent materials. Nonliving biomass of Sargassum, a brown marine alga, is capable of binding more than 10% of its dry weight in toxic cadmium ions. Although ubiquitous iron interferes with Cd uptake, only approximately 4.5% of it is sequestered (biomass dry weight). Biosorption of both metals at pH 4.5 could be described by Langmuir-type isotherms with b, the affinity-related coefficient (Cd: b = 0.015; Fe: b = 0.027). The interference of Fe with Cd uptake, and vice versa, was assessed by deriving three-dimensional equilibrium two-metal sorption isotherm surfaces, smoothed and cut to reveal ...

British Library Electronic Table of Contents (United Kingdom)

Abstract A series of polypropylene carbonate (PPC)/ZnO nanocomposite films with different ZnO contents were prepared via a solution blending method. The morphological structures, thermal properties, oxygen permeability, water sorption, and antibacterial properties of the films were investigated as a function of ZnO concentration. While all of the composite films with less than 5 wt % ZnO exhibited good dispersion of ZnO in the PPC matrix, FTIR and SEM results revealed that solution blending did not lead to a strong interaction between PPC and unmodified ZnO. As such, poor dispersion was induced in the composite films with a high ZnO content. By incorporating inorganic ZnO filler nanoparticles, the diffusion coefficient, water uptake in equilibrium, and oxygen permeability decreased as the ...

Energy Technology Data Exchange (ETDEWEB)

Inhibition efficiency of some water-soluble hydrazones for C-steel corrosion in hydrochloric acid has been tested by weight loss, polarisation measurements and open circuit technique. The inhibition effect was attributed to the adsorption of the additives on the C-steel surface as supported by adsorption measurements at Pt electrode using cyclic voltammetry. Electrochemical measurements indicated that all the additives behave as cathodic-type inhibitors. The data obtained fit well to both the Temkin adsorption isotherm and the kinetic-thermodynamic model. The inhibition behaviour and its order were explained with the help of the proposed skeletal representation.

British Library Electronic Table of Contents (United Kingdom)

In this work, a three-dimensional multiphase non-isothermal model incorporated with a capillary-extended sub-model in gas channels is used to investigate the coupled phenomena of water and thermal transport in proton exchange membrane fuel cells. Distributions of water and temperature along the flow path in the channel are highlighted and the pros and cons of various operating temperatures are elaborated. In addition, this work also sheds light on the impacts of temperature variations of bipolar plates induced by non-uniform cooling conditions, which have been overlooked by most previous works. An important phenomenon of water distribution, dry-out at inlets and flooding at outlets (DIFO), is observed and this non-uniform distribution is revealed to be greatly influenced by the operating t...

British Library Electronic Table of Contents (United Kingdom)

Lignocellulosic fibers from date palm trees were employed to reinforce an epoxy matrix. Two fiber sizes were used, with the length and diameter in the range of 20-30 and 1.5-3 mm, respectively, for the so-called long fibers, and in the range of 5-15 and 0.25-0.75 mm, respectively, for the so-called short fibers. The morphologies of the resulting composites, as well as their thermal, mechanical, and water sorption properties were evaluated. Strong interactions between both components and etherification reactions may occur between the hydroxyl groups of the fibers and the epoxy groups of the epoxy-amine reactive mixture. These effects are emphasized when decreasing the size of the fibers.

Energy Technology Data Exchange (ETDEWEB)

The corrosion behavior of steel in water from certain oil fields with various organic inhibitors was studied by applying potentiodynamic technique at pH 5.9. The inhibitors which were used include 2-methylbenzimidazole (I), 2-mercaptobenzimidazole (II), 2-mercapto-5-methylbenzimidazole (III), and 2-mercaptothiazole (IV). The inhibiting efficiency of the different additives was evaluated from their anodic and cathodic polarization curves at different temperatures. A comparative study of curve fitting procedures using the kinetic thermodynamic model and those utilizing well-known adsorption isotherms was undertaken. Three types of isotherms were used, Langmuir, Frumkin and Flory-Huggins isotherm. The results show that the kinetic-thermodynamic model and Flory-Huggins isotherms are more suitable to fit the data for the four inhibitors, at all applied temperatures. From the values of ...

British Library Electronic Table of Contents (United Kingdom)

The effect of sodium gluconate anion (SG) on the corrosion and scale inhibition of ordinary steel in simulated cooling water has been studied using weight loss, polarisation curves, electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) techniques. SG was studied in concentration from 10-4M to 10-1M. Results obtained reveal that SG perform excellently as corrosion and scaling inhibitor for ordinary steel in simulated cooling water. An increase of SG concentration leads to the increase of the corrosion potential towards the positive direction. The inhibition efficiency was a low temperature dependence. The inhibitor mechanism was treated as an adsorption process according to Langmuir adsorption isotherm. The SEM/EDAX data show that was a corrosion and scale inhi...

Energy Technology Data Exchange (ETDEWEB)

The ORNL high temperature isopiestic apparatus was adapted for adsorption measurements. The quantity of water retained by rock samples taken from three different wells of The Geysers was measured at 150 °C and at 200 °C as a function of pressure in the range 0.00 ≤ p/p₀ ≤ 0.98, where p₀ is the saturated water vapor pressure. The rocks were crushed and sieved into three fractions of different grain sizes (with different specific surface areas). Both adsorption (increasing pressure) and desorption (decreasing pressure) runs were made in order to investigate the nature and extent of the hysteresis. Additionally, BET surface area analyses were performed by Porous Materials Inc. on the same rock samples using nitrogen or krypton adsorption measurements at 77 K. Specific surface areas and pore volumes were determined. These parameters are important in estimating ...

Energy Technology Data Exchange (ETDEWEB)

Three blocks of non-welded tuff, one nominally one cubic foot (trial block) and the other two, nominally one cubic metre (1 m{sup 3}), were excavated from the Busted Butte Test Facility on the Nevada Test Site and transported to the Atomic Energy of Canada Limited Whiteshell Laboratories in Pinawa, Manitoba. The trial block and one of the 1-m{sup 3} blocks were used for unsaturated flow experiments. The remaining 1-m{sup 3} block is being used for saturated flow experiments and will be reported on separately. After a vertical flow of synthetic transport solution was set up under unsaturated conditions, a suite of conservative and chemically reactive radionuclide tracers was injected at volumetric flow rates of 20 mL/hr in the trial block, and 10 mL/hr in the 1-m{sup 3} block. The duration of the migration experiment in the trial block was 87 days, while the migration experiment in the 1-m{sup 3} block was continuing after 600 days. Results obtained from the migration experiment in the ...

International Nuclear Information System (INIS)

Sorption of oxidized and reduced forms of molybdosilicic, molybdophosphoric and molybdovanadophosphoric acids by polyurethane foam based on ethers and esters is studied. On the basis of sorption dependence on solution pH, polyurethane foam type and spectral characteristics of sorbates the suggestion has been made that in the polyurethane foam phase there are two main types of sorbent-sorbate interaction: electrostatic (ion-ion) and with hydrogen bond formation: and it is impossible to determine the contribution of every interaction

Energy Technology Data Exchange (ETDEWEB)

The paper gives results of a study to identify active sites and surface functional groups that may contribute to the absorption of elemental mercury (Hg) by relatively inexpensive calcium (Ca)-based sorbents. The study investigated the formation of chlorine (Cl) sites in CA-based sorbents as well as their role and reactivity in the absorption of Hg. HCl-exposed calcium sulfate dihydrate (gypsum) exhibited a superior Hg sorption capability. Crystalline water molecules on the surface of the gypsum were confirmed to contribute indirectly to Hg uptake. These surface molecules may have absorbed HC1 through hydrogen bond formation between an oxygen atom of a crystalline water molecule and a hydrogen atom of an HCl molecule. Two adjacent, physically absorbed HCl molecules could then trap an Hg molecule through formation of a mercuric-chloride-like molecule. Significant correlations between Cl and Hg uptake by gypsum were noted.

International Nuclear Information System (INIS)

The feasibility of immobilizing simulated radioactive slurry (SRS) by alkali-activated slag---clay minerals composite cement (AASCM) was studied under the experimental conditions. The results show that the dosage of SRS and water cement ratio (W/C) have significant effect on the flowability of the mixture of AASCM and SRS. The more dosage of SRS, the lower flowability. When cement/sand ratio is 1: 1 and W/C is 0.45, the flowability of the mixture meets the case of solidification engineering and the compressive strength of the waste forms containing 20% SRS meets the needs of GB 14569.1-93. The setting time of the mixture of AASCM and SRS is highly dependent on temperature while sorts of anions have little influence on it. The application of AASCM is suitable below 20 degree C. The leaching resistance of AASCM based waste forms is superior to that of OPC based waste forms. The control of the forms to Sr2+ is stronger than that to Cs+. Silicon fume can improve ...

Science.gov (United States)

The applicability of isothermal solidification as a contacting method for solar cells was proved for the systems AgSn and AuIn. The process is advantageous in that it requires no fluxes, no inert gases, and no pretreatment of the components. The IE contac...

Energy Technology Data Exchange (ETDEWEB)

With an objective to clarify the interactions between micropore structure of coal and solvent reagents, a sorption experiment was carried out under solvent saturated vapor pressure. Low-volatile bituminous coal, Pocahontas No. 3 coal, has the aromatic ring structure developed, and makes solvent more difficult to diffuse into coal, hence sorption amount is small. Methanol has permeated since its polarity is high. High-volatile bituminous coal, Illinois No. 6 coal, makes solvent penetrate easily, and the sorption amount was large with both of aromatic and polar solvents. Since brown coal, Beulah Zap coal, contains a large amount of oxygen, and hydrogen bonding is predominant, sorption amount of cyclohexane and benzene having no polarity is small. Methanol diffuses while releasing hydrogen bond due to its polarity, and its sorption amount is large. A double ...

Science.gov (United States)

complexe sur paroi non-isotherme, LContri5ution to the Study thermal ... paroi chaude essentiellement non-isotherme, LVaporization in a Complex ...

International Nuclear Information System (INIS)

Finding environmentally friendly and cost-effective methods to remediate soils contaminated with polycyclic aromatic hydrocarbons (PAHs) is currently a major concern of researchers. In this study, a series of small-scale semi-continuous extractions - with and without in situ wet oxidation - were performed on soils polluted with PAHs, using subcritical water (i.e. liquid water at high temperatures and pressures, but below the critical point) as the removal agent. Experiments were performed in a 300 mL reactor using an aged soil sample. To find the desorption isotherms and oxidation reaction rates, semi-continuous experiments with residence times of 1 and 2 h were performed using aged soil at 250 deg. C and hydrogen peroxide as oxidizing agent. In all combined extraction and oxidation flow experiments, PAHs in the remaining soil after the experiments were almost undetectable. In combined extraction and oxidation no PAHs could ...

International Nuclear Information System (INIS)

The adsorption capacity of radionuclides onto suspended sediment was experimented on each of the coastal seawater sampled around the Kori and the Wolsung nuclear power plant. During the experiment the quantity and size fraction of suspended sediment were adjusted and the seawater and sediment chemistry is approximated to the expected field condition. Because the sorption capacity depends on the specific minerals, ocean chemistry and radionuclide involved, it is necessary to analyze sediment mineralogy. Clay mineral is dominant in seabed mineral and suspended sediment as the result of x-ray diffraction. Radionuclide sorbed to silty-clay mineral can be rather transported to ocean than scavenged to seabed because of low quantity and fine grained suspended sediment in the coast around the Kori and the Wolsung. The result of adsorption examinations shows that "1"3"9Ce and "5"1Cr and "1"1"0"mAg are strongly sorbed to suspended particle, while "1"3"7Cs is less sorbed and ...

British Library Electronic Table of Contents (United Kingdom)

Abstract The available surface equation of state for pure pulmonary surfactant monolayers is generalised to binary mixture monolayers by introducing a group of parameters, i(i-=-1-4) in the form of $x_{r}^{\\beta _{i} } $ to express the influence of the components in new mixing rules and a new factor, I $\\left[ { = \\left( {\\prod\\limits_{i = 1}^{4} {\\beta _{i} } } \\right)^{{\\raise0.5ex\\hbox{$\\scriptstyle 1$}\\kern-0.1em/\\kern-0.15em\\lower0.25ex\\hbox{$\\scriptstyle {4}$}}} } \\right]$, is defined to represent the interaction intensity between two different components. The ---A isotherms getting by the surface equations of state agree with the experimental data for protein-lipid binary monolayers, and the average deviation is about 11.41%. The result shows the order of the interaction intensity b...

Energy Technology Data Exchange (ETDEWEB)

Studies of the adsorption of oxides of sulfur and nitrogen, and their coadsorption, on black carbon in the form of n-hexane soot have been carried out by microgravimetry, EPR and FTIR spectroscopy over a wide range of experimental conditions. The mechanisms of adsorption of O{sub 2} and NO{sub 2} are entirely different, as reflected by adsorption isotherms, the behavior of carbon`s unpaired electrons, the spectral features of surface species formed, mass changes during adsorption-desorption cycles, and an essential lack of competition for surface sites. Significant effects of temperature, water, SO{sub 2} and NO{sub 2} concentration, O{sub 2}, simulated solar radiation, and the presence of trace metals, have been observed and interpreted.

British Library Electronic Table of Contents (United Kingdom)

We studied the sorption of As(III) and As(V) onto ferrihydrite as affected by pH, nature and concentration of organic [oxalic (OX), malic (MAL), tartaric (TAR), and citric (CIT) acid] and inorganic [phosphate (PO4), sulphate (SO4), selenate (SeO4) and selenite (SeO3)] ligands, and the sequence of anion addition. The sorption capacity of As(III) was greater than that of As(V) in the range of pH 4.0-11.0. The capability of organic and inorganic ligands in preventing As sorption follows the sequence: SeO4~SO43 PO4. The efficiency of most of the competing ligands in preventing As(III) and As(V) sorption increased by decreasing pH, but PO4 whose efficiency increased by increasing pH. In acidic systems all the competing ligands inhibited the sorption of As(III) more than As(V), but in alkaline e...

Energy Technology Data Exchange (ETDEWEB)

The removal of toxic metals and alkalis from gas streams at high temperatures was investigated. This is important for the development of coal-fired combined cycle power generation systems.

International Nuclear Information System (INIS)

... adsorption aqueous solutions astatine complexes astatine ions enthalpy organic

Energy Technology Data Exchange (ETDEWEB)

An efficient method of hydrogen storage in nano-porous carbons is its reversible sorption by electrochemical decomposition of a KOH water solution according to the following equation: C + xH{sub 2}O + xe{sup -} {yields} (CH{sub x}) + xOH{sup -} where (CH{sub x}) stands for the hydrogen inserted into the nano-porous carbon during charging and oxidized during discharging. Although various carbon materials have been investigated as hydrogen adsorbents, the information about the storage mechanism as well as the nature of the hydrogen/carbon interaction is still not sufficient. In order to extend the understanding of the process, carbon samples charged electrochemically were investigated by temperature programmed desorption (TPD). The nature of the hydrogen/carbon interaction was studied by electrochemical analysis at different temperatures. The TPD experiments consist of heating the samples from room temperature to 950 C and of quantitative ...

Energy Technology Data Exchange (ETDEWEB)

Hexavalent Cr has been identified as one of the toxic metals commonly present in industrial effluents. Among the treatment techniques developed for removing Cr(VI) from waste waters, sorption is most commonly applied, due to its simplicity and efficiency. However, few adsorbents can be recycled and reused cost-effectively. In this study, the removal and recovery of Cr(VI) from water using Li/Al LDH was investigated. The removal of Cr(VI) by Li/Al LDH was evaluated in a batch mode. The results demonstrated that Cr(VI) adsorption onto Li/Al LDH occurs by replacing the Cl{sup -} that originally exists in the interlayer of the adsorbent. The degree of Cr(VI) adsorption observed for Li/Al LDH was relatively high and the process occurred rapidly; however, a portion of adsorbed Cr(VI) was gradually desorbed, due to the Li de-intercalation of Li/Al LDH. Lithium de-intercalation from Li/Al LDH with interlayer Cl{sup -} and ...

Energy Technology Data Exchange (ETDEWEB)

The INCO ``INCOLOY 800`` trademark groups the Fe-Cr-Ni alloys containing 30 to 35% nickel, 19 to 23% chromium, 0,15 to 0,60% aluminium, 0,15 to 0,60% titanium and less than 0,10% carbon contents, used as construction materials for condenser and heat exchanger tubes. In parallel with water chemistry control and studies aimed at reducing the residual stresses resulting from tube expansion, studies have been conducted to a better understanding of this alloy, its metallurgy and its corrosion behaviour under accurately defined fabrication and heat treatment conditions. The purpose of this paper is to present the results of a behaviour study of INDRET alloy 800 concerning isothermal relaxation and effects of the said relaxation heat treatments on alloy microstructure studied with a transmission electron-chemical method to determine the sensitiveness to intergranular corrosion, and by electrochemistry in pressurized hot water. ...

Science.gov (United States)

The exchange of Eu[sup 3+] for Na[sup +] cations into the sodalite cages of X zeolite (Eu[sub 25]Na[sub 11]X) leads selectively to the isomerization reaction of cyclopropane to propylene. The latter reaction is catalyzed by Broensted acid sites with an apparent activation energy of 10.6 kcal/mol. Sorption measurements of cyclopropane and propylene with Eu/NaX and NaX zeolites at 40 C support the view that Na[sup +] cations might be considered as sites for sorption of these molecules. Force fields created by Eu[sub 4]O[sup 10+] present in Eu/NaX zeolite may affect sorption. On the other hand, Broensted acid sites in Eu/NaX enhance sorption of cyclopropane and propylene at 40 C. Chemisorption of propylene on the Broensted acid sites of Eu/NaX is reversible and may occur via a propylene carbenium cation intermediate. Small amounts of hexene are formed during this sorption. The amount ...

Energy Technology Data Exchange (ETDEWEB)

Dissolved humic substances (humic and fulvic acids) occur in surface waters and groundwaters in concentrations ranging from less than 1 mg(C)/L to more than 100 mg(C)/L. Humic substances are strong complexing agents for many trace metals in the environment and are also capable of forming stable soluble complexes or chelates with radionuclides. Concentrations of humic materials as low as 1 mg(C)/L can produce a detectable increase in the mobility of some actinide elements by forming soluble complexes that inhibit sorption of the radionuclides onto rock materials. The stability of trace metal- or radionuclide-organic complexes is commonly measured by an empirically determined conditional stability constant (K'), which is based on the ratio of complexed metal (radionuclide) in solution to the product concentration of uncomplexed metal and humic complexant. Larger values of stability constants indicate greater complex stability. The ...

Energy Technology Data Exchange (ETDEWEB)

Isothermal reaction experiments were performed in the temperature range of 1000 - 1300 C in order to determine the chemical interactions between Zircaloy-4 fuel rod cladding and Inconel-718 spacer grids of Pressurized Water Reactors (PWR) under severe accident conditions. It was not possible to apply even higher temperatures since fast and complete liquefaction of the components occurred as a result of eutectic interactions during heatup. The liquid reaction products formed enhance and accelerate the degradation of the material couples and the fuel elements, respectively. Only small amounts of Inconel are necessary to liquefy large amounts of Zircaloy. Thin oxide layers on the Zircaloy surface delay the beginning of the chemical interactions with Inconel but cannot prevent them. In this work the reaction kinetics have been determined for the system: as-received and pre-oxidized Zircaloy-4/Inconel 718. The interactions can be described by ...

Energy Technology Data Exchange (ETDEWEB)

Two spreading experiments were performed at the FARO facility with prototypical core melts of a UO{sub 2}/ZrO{sub 2} weight percentage of 80/20. The objective was to obtain data on the spreading at flow rates of about 2 l/s of more than 100 kg prototypic high temperature oxide melt on a dry and wet stainless steel plate. For the second spreading test a shallow water layer of 10 mm was added on the substrate. Solutions for an isothermal spreading with a constant volume flux boundary condition in a sector with an angle {phi} are used to analyse the FARO L-32S experiment and to identify the source of discrepancies between the code results (THEMA, CORFLOW) and the experimental findings. The observed spreading behaviour of both FARO experiments can only be explained if an initial melt temperature below the liquidus temperature, i.e. about 120 K lower than the temperature measured by the UTS sensors is assumed. (orig.) [German] Zwei ...

International Nuclear Information System (INIS)

Three blocks of non-welded tuff, one nominally one cubic foot (trial block) in volume and the other two, nominally one cubic meter (1 m3) in volume, were excavated from the Busted Butte Test Facility on the Nevada Test Site in 1999 and transported to the Atomic Energy of Canada Limited Whiteshell Laboratories in Pinawa, Manitoba. The trial block and one of the 1-m3 blocks were used for radionuclide migration experiments under unsaturated conditions; the remaining 1-m3 block was used for similar migration experiments under saturated conditions. After a vertical flow of synthetic transport solution was set up under unsaturated conditions, a suite of conservative and chemically reactive radionuclide tracers was injected at volumetric flow rates of 20 mL/hr in the trial block, and 10 mL/hr in two locations on the upper surface of the 1-m3 block. These flow rates correspond to infiltration rates of about 120 cm/year and about 17 cm/year, respectively. The duration of the migration ...

Energy Technology Data Exchange (ETDEWEB)

The design of a reaction cell which permits the investigation of the sorption kinetics of microcomponents without separation of the phases under automated condition has been described. The use of thin-layer inorganic sorbents obtained by depositing films of a sorbing substance from aqueous solutions on flat substrates of small thickness makes it possible to determine the extent of sorption even at small values in the case of /beta/ emitters with a low energy and /alpha/ emitters. Detailed observation of the kinetics of isotopic exchange in the CdS-/sup 115m/Cd-HNO/sub 3/ system has made it possible to reveal at least four stages in the process during the time of observation.

International Nuclear Information System (INIS)

Coir pith (CP), an abundantly available lignocellulosic agricultural waste from the local coir industry has been found to be an effective biosorbent for removal of metal ions from aqueous solutions. Transition metal hexacyanoferrates, in particular nickel hexacyano ferrate (NiHCF) also referred to as Prussian blue analogue (PBA), is known to be highly selective for removal of cesium from aqueous solutions. A novel method for the synthesis of PBA inside the porous matrix of coir pith and use of this composite material for the sorption of cesium is described in this paper. Equilibrium experiments showed that the sorption capacity of coir pith nearly doubled due to the modification. Owing to its low cost and rapid sorption kinetics, this hybrid material seems to be one of the most promising compounds for the recovery of cesium from liquid nuclear wastes. (author)

Science.gov (United States)

Metal cations of arsenic, antimony, tin, manganese, zinc, cadmium, indium, and thallium have been evaluated in a preliminary way as possible3 inhibitors for controlling denting corrision observed in steam generators used with pressurized water reactors (PWR). The rationale for this approach was based upon the well-known inhibition effects of metal cations on corrosion rates in electrolyte/metal systems. A review of corrosion inhibition by metal cations (H. Leidheiser, Jr., Corrosion 36, 339 (1982)) has identified eleven inhibition mechanisms. The major test methods used for this evaluation were: (1) Isothermal capsule tests of carbon/steel/Inconel 600 tube bulging rates at temperatures up to 288/sup 0/C in seawater/copper-nickel chloride bulge-accelerating solutions. (2) Immersion weight-loss tests of steel coupled to Inconel 600 in boiling (102/sup 0/C) 3% sodium chloride solutions. In addition, electrochemical measuremens and surface analyses ...

Energy Technology Data Exchange (ETDEWEB)

The present article describes a novel synthesis route for nano-sized goethite ({alpha}-FeOOH) using hydrazine sulphate as an additive. The X-ray diffraction (XRD) peaks of synthesized powder matched well with those of {alpha}-FeOOH. Transmission electron microscopy (TEM) showed the particles of irregular shape in the range of 1-10 nm. Batch adsorption experiments for fluoride uptake were performed to study the influence of various experimental parameters such as contact time (10 min to 7 h), initial fluoride concentration (10-150 mg L{sup -1}), pH (2-11.6) and the presence of competing anions. The time data fitted well to pseudo-second-order kinetic model. The fluoride removal passed through broad maxima in pH ranges of 6-8. High adsorption capacity of 59 mg g{sup -1} goethite was obtained. The isothermic data fitted well to Freundlich model. The presence of other ions namely chloride and sulphate adversely affected fluoride removal. Fluoride from contaminated ...

Energy Technology Data Exchange (ETDEWEB)

The article deals with the problem of a humidity addition to thermal conductivity, diffusion and latent heat effects in heat transfer through building components. It shows with examples humidity effects for exterior walls with core insulation, with composite insulation system as well as for insulated roof membrane assemblies. From these it can be summarized that - sorption humidity is for today`s construction conditions (good thermal insulation and humidity protection) a suitable reference quantity for the determination of practice-oriented, substance-specific and physically correct humidity additions to the thermal conductivity of hygroscopic components; - diffusion and latent heat effects are in case of good rain imperviousness and low water absorbing capacity of the exterior component layers of secondary importance for transmission heat losses; - an increase in insulating layer thickness in order to improve the thermal insulation is possible ...

Science.gov (United States)

... pr h-±rmt of im- mersion isotherme of VIMCH and VYHH which are film formers of v,,yl chloride-acetate co-r~polyrers. VMCH has excelleut r.Lr-dry ...

International Nuclear Information System (INIS)

Mass transfer to a wall of a horizontal rectangular channel reactor was investigated by the limiting current technique for Reynolds numbers ranging from 200 to 32000. Overall mass transfer coefficients at various mass transfer surface angles were obtained while the reactor was operated under isothermal and non-isothermal conditions. Dimensionless correlations were developed for isothermal flows from 25 to 55"oC and for non-isothermal flows with applied temperature differences up to 30"oC. In the laminar flow range natural convection dominated, but under turbulent conditions combined natural and forced convection prevailed. Mass transfer was approximately doubled under optimum selection of channel surface rotation, temperature gradient and flow rate. (author)

Science.gov (United States)

... F ? (28.3)(108) in an isotherme.l deformation with stationary principal axes of strain rate, but the component might be as small as F2= (19-3)(100) ...

Science.gov (United States)

De Lacombe, J., and Dannemuller, M.: Essais de viscosit~ isotherme sur alliages anti-frictions. Rev. Met., March, 1944. Leben, L.: See F. P. Bowden and L. ...

Energy Technology Data Exchange (ETDEWEB)

Progress reports are presented for the following two areas: catalytic cracking studies with water-wet silica-alumina catalysts; and Fischer-Tropsch reactor studies where similarities and differences between fixed bed and slurry type reactors are investigated and further experiments conducted to measure mass transfer coefficients and reaction kinetics which are to be used in a model slurry reactor. The following are some of the conclusions. (1) The premise that the presence of liquid water might increase catalytic cracking activity was found to be invalid. It was demonstrated that cracking can occur at previously unobserved low temperatures (though at low conversions) and that an anomaly exists in that one of the catalysts tested shows an entirely different cracking behavior and probably follows a different cracking mechanism. (2) the diameter of a fixed-bed Fischer-Tropsch reactor critically affected the resistance of the reactor to plugging ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this document is to use existing documentation to review the effectiveness of subsurface flow and surface flow constructed wetlands in treating wastewater and to demonstrate the viability of treating effluent from Savannah River Site outfalls H-02 and H-04 with a subsurface flow constructed wetland to lower copper, lead and zinc concentrations to within National Pollutant Discharge Elimination System (NPDES) Permit limits. Constructed treatment wetlands are engineered systems that have been designed and constructed to use the natural functions of wetlands for wastewater treatment. Constructed wetlands have significantly lower total lifetime costs and often lower capital costs than conventional treatment systems. The two main types of constructed wetlands are surface flow and subsurface flow. In surface flow constructed wetlands, water flows above ground. Subsurface flow constructed wetlands are designed to keep the water level ...

Energy Technology Data Exchange (ETDEWEB)

Fractal dimensions of three different samples of lanthanum ferrite were computed using single adsorption method. The fractal Dubinin-Radushkevitch isotherm was used to fit directly the experimental nitrogen adsorption data. Avnir-Jaroniec method for fractal dimension determination was also used. Low and intermediate fractal dimensions were obtained according to BET specific surface areas.

International Nuclear Information System (INIS)

The efficiency of the synthesized zeolite NaY from rice husk ash (RHA) in the removal of Cr(III) from aqueous solution was studied. Zeolite NaY was synthesized from RHA via seeding technique and the identification of its structure was done by X-ray Diffraction (XRD) technique and the elemental analysis was carried out by X-ray Fluorescence (XRF). The physicochemical properties which were related to the use of the zeolite NaY as a sorbent was also investigated. The synthesized zeolite NaY has higher cation exchange capacity (CEC) than the commercial zeolite NaY due to the higher amount of sodium content in the synthesized as well as the lower ratio of silica to alumina. The synthesized zeolite NaY together with the commercial one as comparison was used in the sorption of the Cr(III) in aqueous solution by batch sorption experiments. The kinetic study showed that the Cr(III) uptake by both zeolites were based on the pseudo second order model. ...

British Library Electronic Table of Contents (United Kingdom)

In this study, the use of the weakly basic anion exchange resins of phenol-formaldehyde (Amberlyst A 23), polyacrylate (Amberlite IRA 67) and polystyrene (Lewatit MonoPlus MP 62) matrices for removal of the reactive dye Remazol Black B (RBB) from aqueous solution and wastewater were investigated. RBB sorption on the anion exchangers was a time dependent process. Color reduction percentiles of 75.2, 33.9 and 25.1% in wastewater treatment were found after 216 h of phase contact time with Lewatit MonoPlus MP 62, Amberlyst A 23 and Amberlite IRA 67, respectively. Inorganic salts and anionic surfactant action influenced RBB uptake by the anion exchangers. The amounts of dye retained by the anion exchangers increased with a rise in temperature. The maximum sorption capacities calculated from the...

Energy Technology Data Exchange (ETDEWEB)

A process for separation of actinides and technetium from reprocessing high level liquid waste has been developed, the CTH-process. The main parts are three consecutive solvent extraction cycles followed by an optional step for sorption on inorganic ion exchangers. The first extraction cycle removes and recovers uranium, neptunium, and plutonium by extraction with HDEHP. The second extraction cycle separates technetium and nitric acid from the waste using TBP. In the third extraction cycle Am and Cm are separated from the waste using HDEHP. The actinide free waste is then passed through inorganic ion exchangers to remove most of remaining radionuclides. The process has been tested on an authenic HLLW solution. A decontamination factor > 10/sup 5/ for alpha emitters was measured for the solvent extraction process and the sorption on inorganic ion exchangers gave a decontamination factor > 3x10/sup 4/ for beta emitters.

Energy Technology Data Exchange (ETDEWEB)

Exchange of hardness ions is important in enhanced oil recovery with chemical additives. In both micellar-polymer and caustic flooding processes, multivalent ions released from rock surfaces can interact with anionic surfactants, rendering them preferentially oil soluble and/or insoluble in water. Because hardness cations are sparingly soluble and precipitate in alkaline solutions, such solutions may be more efficient as surfactant flood preflushes than are softened brines. Multivalent ion precipitation may also occur in alkaline waterflooding. To permit design of such processes, this paper presents a chromatographic theory for simultaneous ion exchange with precipitation of divalent ions. Theoretical effluent histories and concentration profiles are presented for the cases of finite pulses and continuous injection of hydroxide ions into linear cores. Complete capture of the insoluble salt particles is assumed. Results are given for the case of instantaneous ...

Science.gov (United States)

Mesporous anatase-phase TiO(2) hollow spheres with high photocatalytic activity were prepared by hydrothermal treatment and self-transformation of amorphous TiO(2) solid spheres in an NH(4)F aqueous solution. The prepared samples were characterized by X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy, N(2) adsorption-desorption isotherms and UV-vis absorption spectroscopy. The photocatalytic activity was evaluated by photocatalytic oxidation decomposition of acetone in air under UV irradiation. It is found that F(-) plays an essential role in the formation of TiO(2) hollow spheres. F(-) not only induces the hollowing of TiO(2) solid spheres, but also promotes the crystallization of anatase TiO(2) nanocrystals. A possible formation mechanism for the TiO(2) hollow spheres by localized Ostwald ripening or chemically induced self-transformation is proposed based on the experimental observations. Furthermore, the molar ...

British Library Electronic Table of Contents (United Kingdom)

Non-isothermal TG/DTG measurements are widely used to determine kinetic parameters of oxidation and gasification of carbons, e.g. by multi-heating rate methods. Thereby it is important to avoid spurious effects due to diffusion limitations. In this work, TG/DTG experiments with activated carbon were conducted under isothermal and non-isothermal conditions. The agreement of the experimental results with results of simulations based on the intrinsic kinetics, pore diffusion and external diffusion in/to the sample (crucible) is very good. The simulations show that mass transfer has an unwanted influence on TG measurements, if the concentration of the gaseous reactant (O2 and CO2) is too low and/or the heating rate is too high. Based on literature data, the simulation was extended to blast fur...

British Library Electronic Table of Contents (United Kingdom)

b-carotene, a natural antioxidant, beneficial form human health prospective. In this study we had examined the recovery of b-carotene form mesoporous carbon coated monolith (MCCM) by batch process. Desorption kinetics and isotherm studies were carried out by using n-hexane as an eluent. Isotherm studies showed better applicability of Langmuir model. The first-order two-compartment three-parameter kinetics model as a function of initial loading concentration and reaction temperature was applied. It was observed that b-carotene desorption process is controlled by both rapid and slow desorption. Results showed that the slow desorption fraction increases from 0.8446 to 0.9007 with increase in initial loading concentration from 10.83 to 39.72mg/g while, the slow desorption fraction decreases fr...

Energy Technology Data Exchange (ETDEWEB)

In contrast to plants based on formed coal where, for the purposes of calculating sorbent volume, only one activated charcoal design can be used in a filter layer, powder sorbent technology enables two variations to be used. This can be either a mixture of a number of different activated charcoal forms in one and the same filter layer, or the combination of a number of filter layers on top of each other, each containing a different activated charcoal form, in one and the same construction unit.

Energy Technology Data Exchange (ETDEWEB)

We intend to solve equations governing turbulent plane-vertical isotherm and non isotherm jets by taking into account inflow conditions at the exit of the nozzle. The analysis is focused on the influence of these conditions on this type of flow. Two cases are considered (uniform and parabolic velocity and temperature profiles). A finite difference scheme is developed to solve the governing equations. This numeric model allows us to show that the region of fully developed regime begins much nearer the nozzle for the turbulent case than for the laminar flow case. Indeed, the turbulence increases the mixing between the incoming gas from the nozzle and the ambient fluid, and consequently the size of the potential core zone decreases. The results are compared to other works introducing mathematical variables based on the energy conservation for the case of the mixed convection and the momentum conservation for the forced convection, which allows the ...

Science.gov (United States)

isotherme, dans un courant d'azote ou sous vide entretenu. I t. Comptes Rendus Scientific Academy, Paris, Vol. 265 pyrolyse du carbonate de calcium, ...

Energy Technology Data Exchange (ETDEWEB)

A Paderborn group of builder-owners decided in favour of so-called concrete core activation or isothermal component tempering as an alternative to conventional air conditioning. Results are now available for the first year of operation. [German] Am eigenen Neubau hat eine Paderborner Bauherrengemeinschaft die sogenannte Betonkernaktivierung - oder wie es die Bauherren nennen, isotherme Baukoerpertemperierung - als Alternative zu einer konventionellen Klimaanlage installiert. Inzwischen liegen die Messergebnisse von der ueber einjaehrigen Betriebszeit vor. (orig.)

Energy Technology Data Exchange (ETDEWEB)

An efficient method of hydrogen storage in nano-porous carbons is its reversible sorption by electrochemical decomposition of a KOH water solution [1-3] according to the following equation: C + xH{sub 2}O + xe{sup -} {yields} (CH{sub x}) + xOH{sup -} where (CH{sub x}) stands for the hydrogen inserted into the nano-porous carbon during charging and oxidized during discharging. Although various carbon materials have been investigated as hydrogen adsorbents, the information about the storage mechanism as well as the nature of the hydrogen/carbon interaction is still not sufficient. In order to extend the understanding of the process, carbon samples charged electrochemically were investigated by temperature programmed desorpt(TPD). The nature of the hydrogen/carbon interaction was studied by electrochemical analysis at different temperatures. The TPD experiments consist of heating the samples from room temperature to 950 C and of quantitative ...

Science.gov (United States)

Programs & Services Technical Resources Land Use Soils Water Snow Survey & Water Supply Water Management Water Quality Watersheds Wetlands Air Plants & Animals Energy Climate...

International Nuclear Information System (INIS)

Based on an multivariate statistical evaluation of binary and metric data relating to the soil cover of the European Community five regionally representative reference soils (EURO-Soils) have been identified for chemicals testing in the EC. The soil material sampled at representative localities in Italy, Greece, Great Britain, France and Germany was treated and prepared according to OECD Test Guideline 106 and analysed in detail. The homogenised specimens were subject to an EC-wide ring test to evaluate the feasibility of the modified guideline and to validate the physical-chemical amenability of the reference soils for sorption tests. The results proved the validity of the soils selected for assessing the potential behaviour of new chemicals in soil on the basis of a comparative evaluation of the individual test results obtained. In the light of this parametric assessment potential test soils were subsequently identified in the individual EC Member States which ...

Science.gov (United States)

The effect of organic (fulvic and humic acids) and inorganic fractions of soil on the sorption and extractability of /sup 239/Pu(IV) as a function of pH was determined by using an equilibrium batch technique. The results indicated that Pu(IV) is strongly sorbed on the inorganic fraction of the soil under soil pH conditions normally encountered in natural environments. Plutonium appeared to form stable complexes or chelates with fulvic and humic acids in the pH range studied (1.3 to 11.7). In mixtures of pure fulvic or humic acids with soil inorganic fractions, extractability of Pu was substantially influenced by organic-inorganic interaction. The influence of the inorganic fractions was most evident in the lower pH ranges, whereas that of the organic materials was most evident in the higher pH ranges, generally above pH 6. Some implications of the results on plutonium movement in soils were discussed.

British Library Electronic Table of Contents (United Kingdom)

Uranium has varying degrees of oxidation (+4 and +6) and is responsive to changes in the redox potential of the environment. It is deposited at the reduction barrier with the participation of biota and at the sorption barrier under oxidative conditions. Iron (hydr)oxides are the strongest sorbents of uranium. Uranium, being an element of medium biological absorption, can accumulate (relative to thorium) in the humus horizons of some soils. The high content of uranium in uncontaminated soils is most frequently inherited from the parent rocks in the regions of positive U anomalies: in the soils developed on oil shales and in the marginal zone of bogs at the reduction barrier. The development of nuclear and coal-fired power engineering resulted in the environmental contamination with uranium....

Energy Technology Data Exchange (ETDEWEB)

Metal hydrode stores are used as fuel tanks in vehicles or as stationary stores of high-purity hydrogen. Equilibrium isotherms at low pessures were measured in order to validate the laws of Henry or Sievert for hydrogen uptake of the alloy Ti{sub 0.98}Zr{sub 0.02}V{sub 0.43}Fe{sub 0.09}Cr{sub 0.05}Mn{sub 1.5} (patented by Daimler Benz AG, code DB5800). The laws were to provide information on whether hydrogen uptake is atomic or molecular and on the conditions in which isothermal measurements are possible. (orig.) [Deutsch] Metallhydridspeicher werden als Kraftstofftank in Fahrzeuge oder als stationaere Speicher zur Bereitstellung von Reinstwasserstoff verwendet. Fuer diese Arbeit wurden die Gleichgewichtsisothermen bei kleinen Druecken vermessen, um die Gesetze von HENRY oder SIEVERT fuer die Wasserstoffaufnahme in der Legierung Ti{sub 0.98}Zr{sub 0.02}V{sub 0.43}Fe{sub 0.09}Cr{sub 0.05}Mn{sub 1.5} zu pruefen. Anhand dieser Gesetze ist zu ...

International Nuclear Information System (INIS)

The applicability of in situ, real-time RBS is demonstrated by characterizing the growth of thin Pd_2Si films on Si left angle 111 right angle substrates using isothermal as well as non-isothermal annealing. In contrast to the currently fashionable in situ ramped resistance technique, it is possible to extract the activation energy from a single run with a constant heating rate. The results, which are in excellent agreement with the literature, will be compared for isothermal annealing, fitting an appropriate model for the growth process to data from a single run and a Kissinger-like analysis with different ramp rates. In situ, real-time RBS was also used to study marker motion during CrSi_2 formation in the Si left angle 100 right angle /Pd_2Si/Cr system. It is possible to distinguish between the following mechanisms: (1) CrSi_2 formation via dissociation of the Pd_2Si at the Pd_2Si/Cr interface and subsequent reaction of ...

Energy Technology Data Exchange (ETDEWEB)

This study focused on the biosorption of total chromium onto red algae (Ceramium virgatum) biomass from aqueous solution. Experimental parameters affecting biosorption process such as pH, contact time, biomass dosage and temperature were studied. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherms. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The biosorption capacity of C. virgatum biomass for total chromium was found to be 26.5 mg/g at pH 1.5 and 10 g/L biomass dosage, 90 min equilibrium time and 20 deg. C. From the D-R isotherm model, the mean free energy was calculated as 9.7 kJ/mol, indicating that the biosorption of total chromium was taken place by chemisorption. The calculated thermodynamic parameters ({delta}G{sup o}, {delta}H{sup o}and {delta}S{sup o}) showed that the biosorption of total chromium onto C. virgatum biomass ...

Science.gov (United States)

for? Learn the Issues Science & Technology Laws & Regulations About EPA Contact Us Water: Water Quality Criteria You are here: Water Science & Technology Surface Water Standards &...

Energy Technology Data Exchange (ETDEWEB)

The isothermal flow field for the axial cyclone has been experimentally determined. The velocity fields are used for determination particle paths (particle removal and suspended state), and inter alia of heat and mass transfer processes in the axial cyclone combustion chamber. The results are extremely significant as input value approximations for mathematical modelling, since experimentally obtained results are indispensable for complex flows and geometries. (orig.) [Deutsch] Es ist fuer den Axialzyklon experimentell das isotherme Stroemungsfeld ermittelt. Die Geschwindigkeitsfelder dienen zur Ermittlung der Partikelbahnen (Partikelabscheidung, Schwebebedingung), der Waerme- und Stoffuebertragungsprozesse u.a. in der Axialzyklonbrennkammer. Die Ergebnisse sind als Startwertnaeherung bei einer mathematischen Modellierung sehr wichtig, da bei komplexen Stroemungen und Geometrien versuchstechnische Ergebnisse unumgaenglich sind. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Abstract In this study, surfactant-modified zeolite (SMZ) was used to remove Remazol Brillant Blue R and Remazol Yellow reactive dyes from aqueous solutions. The influences of suspension pH, temperature, agitation rate, and the SMZ dosage on reactive dyes removal and adsorption capacity were investigated by conducting a series of batch adsorption experiments. The adsorption kinetics was tested for pseudo-first-order, pseudo-second order, intraparticle diffusion model, Elovich, and Bangham models, and rate constants of the kinetic models were calculated. Equilibrium isotherms for the adsorption of reactive dyes were analyzed by the Freundlich, Langmuir, Dubinin-Radushkevich, and Tempkin isotherm models. The Langmuir monolayer adsorption capacities of Remazol Brillant Blue R and Remazol Yell...

British Library Electronic Table of Contents (United Kingdom)

ResumeLa convergence des solutions faibles du systeme de Navier-Stokes-Fourier-Poisson compressible avec un terme de frottement est etudiee dans la limite dun frottement infini, la loi de pression incluant, comme cas particulier, celle correspondant aux particules de Fermi-Dirac. La limite se trouve etre une solution faible dun systeme de Smoluchowski-Poisson non isotherme, la temperature ne dependant que de la variable temporelle et etant determinee par la conservation de lenergie totale.

British Library Electronic Table of Contents (United Kingdom)

In this paper, the effects of surface mediation on the adsorption isotherm and isosteric heat of adsorption on a graphite surface were investigated, as the surface mediation is known to affect the intermolecular interaction of adsorbed molecules close to the surface. Kim and Steele (Phys. Rev. B 45 (11) (1992) 6226-6233) and others have assumed that the surface mediation is confined only to the first layer. This will be tested in this paper with a combined experimental and Grand Canonical Monte Carlo (GCMC) simulation of adsorption of argon on graphitized thermal carbon black (GTCB) over a range of temperatures (77-95.25K). By matching the simulation results against the experimental data, we have found that the surface mediation is extended up to the fourth layer, rather than only the firs...

Energy Technology Data Exchange (ETDEWEB)

Two isothermal sections were prepared at 1000 and 1150 C showing the low-Zr phases of the system Fe-Al-Zr. The phase equilibria were determined by means of X-ray powder diffractometry and electron beam microanalysis. For initial characterisation of mechanical properties, hardness values are determined and added to the tabulated data. (orig./MM) [German] Es werden am Fe-Al-Zr-System zwei isotherme Schnitte durch den zirkoniumarmen Teil des Systems bei 1000 und 1150 C erstellt. Die auftretenden Phasengleichgewichte werden mit Hilfe der Roentgenpulverdiffraktometrie und Elektronenstrahlmikroanalyse aufgeklaert. Zusaetzlich werden zur ersten Charakterisierung der mechanischen Eigenschaften Haertewerte bestimmt.

International Nuclear Information System (INIS)

Charge carrier profiles are measured for boron implanted into silicon (E = 30 keV, dose range 5 x 10"1"5 to 2 x 10"1"6 B/cm"2) after rapid isothermal annealing using halogen lamps. Maximum temperatures between 1000 and 1300 "0C and holding times at T/sub max/ of 5 and 20 s are used for the annealing treatment. In a few additional experiments flash lamp annealing at 1350 "0C (pulse duration 20 ms) is investigated. By comparison of the experimental profiles with computer simulations using the SUPREM II program transient enhanced diffusion of boron could be detected in all investigated cases. Maximum charge carrier concentrations above the equilibrium solubility of boron are observed and are discussed. (author).

International Nuclear Information System (INIS)

... hydrology norway water pollution pollution scandinavia surface waters

Energy Technology Data Exchange (ETDEWEB)

This report summarises nearly 20 biosphere reports and gives a synthesis of the work performed within the SR-Site Biosphere project, i.e. the biosphere part of SR-Site. SR-Site Biosphere provides the main project with dose conversion factors (LDFs), given a unit release rate, for calculation of human doses under different release scenarios, and assesses if a potential release from the repository would have detrimental effects on the environment. The intention of this report is to give sufficient details for an overview of methods, results and major conclusions, with references to the biosphere reports where methods, data and results are presented and discussed in detail. The philosophy of the biosphere assessment was to make estimations of the radiological risk for humans and the environment as realistic as possible, based on the knowledge of present-day conditions at Forsmark and the past and expected future development of the site. This was achieved by using the best available ...

British Library Electronic Table of Contents (United Kingdom)

Parameters of the vortex air flow in an isothermal model of the cyclone chamber are studied. The effect of the air velocity in nozzles on the values and character of the distribution of pressure and tangential and longitudinal velocities of air in the chamber is determined. Numerical modeling of the flow is performed, and it is shown that numerical calculation by the k-w turbulence model is in agreement with experimental data.

Energy Technology Data Exchange (ETDEWEB)

CdTe/SnTe heterojunctions, prepared by EDRI (evaporation-diffusion en regime isotherme) and CSVT (close spaced vapour transport) techniques, have a spectral response in a wide wavelength range (0.3 - 1.5 ..mu..m) which exhibits two distinct bands, corresponding to carrier generation in each material of the couple. Experimental results are interpreted in terms of a Schottky diode model. (orig.).

Science.gov (United States)

The primary of this thesis is the derivation of nonisothermal equations for isotropic viscoelastic materials with the help of the thermodynamics. Because the description of all phenomena would be too ambitious for one thesis, the area of investigation has...

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is to be able to describe transformations, occurring when solids and gases are in non isothermal and non isobaric conditions, with kinetic models. A methodology has been used. Two essential processes have to be taken into account: the germination and the growth. The germs are supposed to be formed (at constant temperature and pressure) in the grains surface with a constant velocity by surface unit, (gamma), called germination surface frequency (number of germs.m{sup -2}.s{sup -1}. The growth velocity is characterized by a growth surface reactivity, (phi) (in mol.m{sup -2}.s{sup -1}). With an appropriate transformation model, it is possible to obtain the variations of (gamma) and (phi) in terms of the temperature and pressure which are then used in the calculation of the velocity in non isothermal and non isobaric conditions. In order to validate the developed method, two reactions have been studied. For the first one, the ...

Energy Technology Data Exchange (ETDEWEB)

X-ray results on the lattice parameters, molar volume and thermal expansion coefficients of solid ortho-deuterium for the region from 2 K to the melting point are reported. It is found that the thermal expansion of ortho-deuterium crystals, similarly to parahydrogen is essentially anisotropic near the melting temperature. The vacancy density at the triple point is estimated. Some thermodynamic characteristics of ortho-deuterium are calculated and temperature dependences of heat capacity at constant volume, isothermal compressibility and Gruneisen constant are analyzed.

International Nuclear Information System (INIS)

It if first shown, that the effective field of uniaxial magnetic anisotropy of Fe-Cr-P-C and Fe-Ni-B-Si system amorphous alloys is reduced with an increase of the source melt isothermal exposure time. The behaviour noted is conditioned by microcoherence and relaxation processes in the nonequilibrium liquid phase after crystal-liquid phase transition.

Energy Technology Data Exchange (ETDEWEB)

This report measured the rate of isothermal deposition of sub-micron particles of magnetite onto the surface of Alloy 800 at pH of 4.2-9.3 at Re=10,000 and a fluid temperature of 25C. Deposition is modelled as a two-step process, the transport of particles to the surface region followed by attachment to the surface.

Energy Technology Data Exchange (ETDEWEB)

In this paper a phenomenological analysis of the sintering kinetics of alumina powder compacts with different proportions of small and large particles has been made. A phenomenological approach enables definition of functional connections between parameters characteristic of a certain material and the sintering time. A phenomenological equation is defined, which can be used to describe the densification process of alumina during isothermal sintering. Its parameters enable identification of the dominant diffusion mechanism. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The ODS superalloys MA 6000 and MA 760 were investigated with regard to their behaviour under non-isothermal fatigue stress. For this purpose, strain-controlled thermomechanical and bithermal experiments with different phase relationships between strain and temperature were carried out on the one hand; on the other hand, the deformation behaviour under thermomechanical stress was modelled on the basis of isothermal cyclic creep data. The fatigue experiments show that a diamond-shaped cycle derived from the stress pattern of a turbine blade is clearly less critical than in-phase and out-of-phase cycles. The life of the diamond-shaped cycle is determined by oxidation-induced crack initiation and propagation and can be predicted easily with a suitable damage model. Important damage parameters required by the model can be obtained by the less complicated bithermal fatigue tests. Modelling of the TMF hystereses suggests that cyclic, ...

British Library Electronic Table of Contents (United Kingdom)

The thermodynamic characteristics of sorption of the isomeric tricyclo[5.2.1.02.6]decane (tetrahydrodicyclopentadiene, TDCPD) molecules were for the first time determined experimentally and by molecular statistical methods under the conditions of gas-adsorption chromatography on graphitized thermal carbon black and gas-liquid chromatography on stationary liquid phases of different polarities (Apiezon L and Carbowax 20M). The effects of the chemical nature of sorbents on the retention of the TDCPD isomers are considered. A procedure for calculating the thermodynamic characteristics of adsorption of molecules with a complex structure is suggested within the framework of the atom-atom approximation of the semiempirical molecular statistical theory of adsorption for the example of isostructura...

British Library Electronic Table of Contents (United Kingdom)

A prerequisite for a sensible estimate of moisture induced stresses in timber members is an accurate prediction of the members' moisture states during their service life. There are, however, an infinite number of possible moisture states for an arbitrary timber member in a natural varying climate. The naturally varying humidity is possible to describe as harmonic cycles, with different periods, superimposed. This work presents realizations of envelop curves over the possible moisture states in a timber member for some carefully chosen harmonic humidity variations. The calculations, on which the realizations were made, are based on a fully coupled transport model including a model for the influential sorption hysteresis of wood. A format containing required information suitable for assessin...

International Nuclear Information System (INIS)

It is known that the plant cuticle represents the first barrier that must be overcome by any chemical reaching the plant surface from the atmosphere before entering the plant. Because of the importance of the cuticle as a barrier to penetration of a wide variety of compounds, its morphology, chemistry, and permeability have been extensively studied. However, only limited information is available on the nature of functional chemical groups present and their interaction and role during the penetration process. The usefulness of in situ Fourier transform infrared spectroscopy studies in identifying functional groups present in isolated cuticles is described and their relationships to the structure of the cuticular membrane are discussed. Applications of infrared spectroscopy on the presence and role of phenolics in the cuticle structure and during the cuticle development, nitrogen oxide binding to isolated cuticles, and the interactions between selected chemical probes during ...

International Nuclear Information System (INIS)

Natural minerals and some industrial wastes are used as low cost sorbents for removal of metal ions from effluent streams. Apatite as natural mineral and red mud as an industrial waste have been tested for their sorption properties with respect to two important fission products "1"3"7Cs and "9"0Sr. Their ion exchanging capacity was tested after every 4 hours till 24 hours. The material gets saturated after 4-8 hours. Hence these materials can be considered for treating in treating LLW before discharge, industrial waste treatment and as backfill or admixture material for shallow land repository. (author)

Energy Technology Data Exchange (ETDEWEB)

We studied the interaction of Pu(VI) with Pseudomonas stutzeri ATCC 17588 and Bacillus sphaericus ATCC 14577, representatives of the main aerobic groups of soil bacteria present in the upper soil layers. The accumulation studies have shown that these soil bacteria accumulate high amounts of Pu(VI). The sorption efficiency toward Pu(VI) decreased with increasing biomass concentration due to increased agglomeration of the bacteria resulting in a decreased total surface area and number of available complexing groups. Spores of Bacillus sphaericus showed a higher biosorption than the vegetative cells at low biomass concentration which decreased significantly with increasing biomass concentration. At higher biomass concentrations (> 0.7 g/L), the vegetative cells of both strains and the spores of B. sphaericus showed comparable sorption efficiencies. Investigations on the pH dependency of the biosorption and extraction studies with 0.01 M ...

Energy Technology Data Exchange (ETDEWEB)

The uncertainty associated with the sorption coefficient, or K{sub d} value, is one of the key uncertainties in estimating risk associated with burying low-level nuclear waste in the subsurface. The objective of this study was to measure >648 K{sub d} values and provide a measure of the range and distribution (normal or log-normal) of radionuclide K{sub d} values appropriate for the E-Area disposal site, within the Savannah River Site, near Aiken South Carolina. The 95% confidence level for the mean K{sub d} was twice the mean in the Aquifer Zone (18-30.5 m depth), equal to the mean for the Upper Vadose Zone (3.3-10 m depth), and half the mean for the Lower Vadose Zone (3.10-18 m depth). The distribution of K{sub d} values was log normal in the Upper Vadose Zone and Aquifer Zone, and normal in the Lower Vadose Zone. To our knowledge, this is the first report of natural radionuclide Kd variability in the literature. Using ranges and distribution coefficients ...

Energy Technology Data Exchange (ETDEWEB)

Water-resources data for the 1991 water year for Minnesota consist of records of stage, discharge and water quality of streams; stage, contents, and water quality of lakes and reservoirs; and water levels and water quality in wells and springs. The volume contains discharge records for 60 gaging stations; stage and contents for 9 lakes and reservoirs; water quality for 18 stream stations, 1 lake station, 22 partial-record sites, 1 precipitation station, 108 wells; and water levels for 119 observation wells. Also included are 59 high-flow partial-record stations. Additional water data were collected at various sites, not part of the systematic data collection program and are published as miscellaneous measurements or low-flow investigations.

Science.gov (United States)

swimmers in or around the water. Designate a responsible adult who can swim and knows CPR to watch swimmers in or around water. The supervisor should not be involved in any...

Energy Technology Data Exchange (ETDEWEB)

Multi-walled carbon nanotubes (MWNTs) were modified with poly(hexamethylene adipamide) (also known as Nylon 66) via a controlled polymer solution crystallization method. A 'nanohybrid shish kebab' (NHSK) structure was found wherein the MWNT resembled the shish while Nylon 66 lamellar crystals formed the kebabs. These Nylon 66-functionalized MWNTs were used as precursors to prepare polymer/MWNT nanocomposites. Excellent dispersion was revealed by optical and electron microscopies. Nitric acid etching of the nanocomposites showed that MWNT formed a robust network in Nylon 66. Non-isothermal DSC results showed multiple melting peaks, which can be attributed to lamellar thickness changes upon heating. The crystallite sizes L{sub 100} and L{sup 010} of Nylon 66, determined by WAXD, decreased with increasing MWNT contents. Isothermal DSC results showed that crystallization kinetics increased first and then decreased with increasing ...

Energy Technology Data Exchange (ETDEWEB)

The simultaneous biosorption of Cr(VI) and Cu(II) on free Rhizopus arrhizus in a packed column operated in the continuous mode was investigated and compared to the single metal ion situation. The breakthrough curves were measured as a function of feed flow rate, feed pH, and different combinations of metal ion concentrations in the feed solutions. Column competitive biosorption data were evaluated in terms of the maximum (equilibrium) capacity in the column, the amount of metal loading on the R. arrhizus surface, the adsorption yield, and the total adsorption yield. In the single-ion situation the adsorption isotherms were developed for optimum conditions, and it was seen that the adsorption equilibrium data fit the noncompetitive Freundlich model. For the multicomponent adsorption equilibrium the competitive adsorption isotherms were also developed. The competitive Freundlich model for binary metal mixtures represented most the column ...

Energy Technology Data Exchange (ETDEWEB)

A study has been made of the precipitation and growth processes which occur during cooling from solution treatment and under isothermal hold conditions in a magnesia-partially-stabilized zirconia alloy. Three types of precipitate have been identified which develop during cooling or during isothermal hold treatments just above and below the eutectoid temperature. These precipitate forms are termed (i) primary, (ii) large random, and (iii) secondary. Further precipitation, slow growth of existing precipitates, and subeutectoid decomposition result when an additional 1100/sup 0/C aging treatment is given to the previously cooled material. It is shown that type (iii) secondary precipitates from rapidly within the temperature range of 1300/sup 0/ to 1375/sup 0/C. The secondary precipitates are largely responsible for the improved room-temperature strength properties of the heat-treated samples. The formation and effects on mechanical properties of ...

Energy Technology Data Exchange (ETDEWEB)

The {delta} {yields} {alpha}{prime} martensitic transformation in Pu-1.9 at.% Ga occurs when the alloy is cooled below about -100 C. This transformation exhibits anomalous behavior, where the isothermal transformation proceeds atypically with double-C kinetics. Recent work has revealed that an ambient temperature isothermal hold (referred to as conditioning) prior to the transformation has different effects depending on whether transformation proceeds in the upper- or lower-C of the double-C: the amount of transformation is increased with conditioning in the upper-C, while the transformation in the lower-C seems to be engendered by conditioning. The mechanism by which conditioning affects the low-temperature {delta} {yields} {alpha}{prime} transformation is thus of great importance to understanding the transformation itself as well as the general circumstances that can affect a martensitic phase transformation. Using differential scanning ...

Energy Technology Data Exchange (ETDEWEB)

The paper examines the influence of various total strain amplitudes and mean strains on the cyclic deformation processes in GGG-60 at temperatures of 20 C, 350 C, and 500 C ,the total strain amplitudes being varied between 1.0 permille {<=}{epsilon}{sub a,t}{<=}3.8 permille , and the mean strains between -4.0 permille {<=}{epsilon}{sub m,t}{<=}4.0 permille . - [Deutsch] In der Arbeit wird der Einfluss unterschiedlicher Totaldehnungsamplituden und Mitteldehnungen auf das Wechselverformungsverhalten von GGG-60 bei Temperaturen von 20 C, 350 C und 500 C untersucht. Dabei werden die Totaldehnungsamplituden zwischen 1,0 permille {<=} {epsilon}{sub a,t} {<=} 3,8 permille und die Mitteldehnungen zwischen -4,0 permille {<=} {epsilon}{sub m,t} {<=} 4,0 permille variiert. (orig./MM)

Energy Technology Data Exchange (ETDEWEB)

The microelectronic cable diagnosis is a substantial tool to determine destruction free the residual strength and the lifetime of laid PE/XLPE medium voltage cables. Fundamentals of the ageing diagnosis and a cost reduced inspection concept are the `Isothermal-Relaxation-Current` Analysis and the Neuro-Fuzzy evaluation software. These new tools are able to determine the ageing status of the investigated cable without any references. The authors also show that the test breakdown during the assessment of the ageing status of criterial systems can be reduced by this approach. The cable diagnosis equipment KDA is also useful for the steering of investment as well as for preventive maintenance. (orig.) [Deutsch] Die zerstoerungsfreie dielektrische Kabeldiagnostik kann heute einen wesentlichen Beitrag zur Bestimmung der Restfestigkeit und der Restlebensdauer eines PE/VPE-isolierten Mittelspannungskabels leisten. Basis der Alterungsdiagnose und des Konzeptes zur ...

Energy Technology Data Exchange (ETDEWEB)

The biosorption of Acid Red 274 (AR 274) dye on Enteromorpha prolifera, a green algae grown on Mersin costs of the Mediterranean, Turkey, was studied as a function of initial pH, temperature, initial dye and biosorbent concentration. The experiments were conducted in a batch manner. The Langmuir and Freundlich isotherms were used for modelling the biosorption equilibrium. At optimum temperature 30 deg C and initial pH 2.0-3.0, the Langmuir isotherm fits best to the experimental equilibrium data with a maximum monolayer coverage of 244 mg/g. The equilibrium AR 274 concentration of the exit stream of a single batch was also obtained by using the experimental equilibrium curve and operating line graphically. The pseudosecond-order kinetic model and Weber-Morris model were applied to the experimental data and it was found that both the surface adsorption as well as intraparticle diffusion contribute to the actual adsorption process. The biosorption ...

Energy Technology Data Exchange (ETDEWEB)

Isothermal transformation kinetics of austenite to acicular ferrite and allotriomorphic ferrite were measured in reheated low alloy steel weld deposits with similar weld compositions and austenite grain size but different inclusion characteristics. Accelerated kinetics of transformation to acicular ferrite were observed in weld metal containing coarser and titanium-rich inclusions. In contrast, kinetics of transformation to allotriomorphic ferrite were not influenced by inclusion characteristics, but, rather, by the austenite grain size and carbon concentration.

Science.gov (United States)

Convective losses arising from buoyancy driven flow were calculated for a two-dimensional model simulating a solar cavity receiver. The TEMPEST code, capable of fully three-dimensional coupled thermal-hydraulic transient calculations, was used for the simulation. Predicted velocity and temperature results for a 2.59 m deep by 2.88 m high rectangular cavity with an aperture opening of 1.72 m were used to determine convective losses for prescribed interior wall temperatures and cavity orientation. Velocity vector and temperature isotherm plots were used to analyze flow characteristics.

British Library Electronic Table of Contents (United Kingdom)

Isosteric heats and adsorption isotherms of methane on nanometer active carbon were measured at supercritical temperature (273-373 K) and pressure from 0 to 10 MPa. The measured data agreed well with Dubinin-Astakhov (DA) model at lower pressure but failed when pressure exceeded a special range. General Freundlich (GF) equation was used to modify the DA equation at high pressure and thus formed a combined bisection model GFDA. The adsorption mechanism of methane on nanometer active carbon was raised according to GFDA model and the heterogeneous energy distribution of the adsorbent was analyzed.

Science.gov (United States)

Fluidized bed technology was experimentally evaluated for the combustion and gasification of cotton gin waste. The isothermal bed temperatures in the reactors could be maintained below the ash fusion point of the waste. Raw stripper harvested cotton gin trash could be metered directly into the fluidized-bed reactors indicating that little feed preparation is required. H and CO were the primary products of gasification, and approximately 3200-400 Btu of gas were produced per lb of cotton gin waste. These techniques offer the potential of providing small-scale energy conversion systems for use on farms.

International Nuclear Information System (INIS)

The effect of a mineralizer, magnesium silicate, on the nitridation of compacts consisting of silicon, clay, silica and silicon carbide was examined in terms of their reaction depth, density, porosity, phase composition and microstructure. It was found that addition of mineralizer slowed down the nitridation significantly. The kinetic process of isothermal nitridation in the presence of magnesium silicate obeys a parabolic rate law. Otherwise it obeys a linear rate law. The results suggest that nitrogen transportation is the limiting step during nitridation when mineralizer is added. The mechanism of nitridation is discussed in terms of phase composition and microstructure. Copyright (2000) The Australian Ceramic Society

Energy Technology Data Exchange (ETDEWEB)

Creep properties of modified 9 Cr-1 Mo steel, an alloy significantly improved in elevated-temperature strength over 2 1/4 Cr-1 Mo and other similar alloys, are presented here. Data are primarily on material in the normalized and tempered condition. Effects of variables such as isothermal annealing treatment, cold work, normalizing temperature, tempering temperature, notch, and biaxial stress state have also been examined. Data analysis and comparisons have shown that modified 9 Cr-1 Mo alloy is very insensitive in response to several material variables, heat treatments, and specimen design variables.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Apparent molar volumes of aqueous methyldiethanolamine and its salt were determined with platinum vibrating tube densitometers over a range of temperatures from 283K=<T=<576K and at pressures from 0.1MPa to 20MPa. Apparent molar heat capacities were obtained using a Sodev Picker flow microcalorimeter at a pressure of 0.1MPa and within the temperature range of 283K=<T=<328K. Apparent molar adiabatic and isothermal compressibilities at a pressure of 0.1MPa were obtained at temperatures from 283K=<T=<313K with speed of sound measurements. The experimental results were extrapolated to infinite dilution to obtain values for the standard partial molar volumes V{sup o}, heat capacities C{sub p}{sup o}, and isothermal compressibilities {kappa}{sub T}{sup o}. The standard partial molar volumes V{sup o} for the neutral amine and its salt show increasingly positive and negative values, respectively, at high ...

Science.gov (United States)

In this paper, the effects of surface mediation on the adsorption isotherm and isosteric heat of adsorption on a graphite surface were investigated, as the surface mediation is known to affect the intermolecular interaction of adsorbed molecules close to the surface. Kim and Steele (Phys. Rev. B 45 (11) (1992) 6226-6233) and others have assumed that the surface mediation is confined only to the first layer. This will be tested in this paper with a combined experimental and Grand Canonical Monte Carlo (GCMC) simulation of adsorption of argon on graphitized thermal carbon black (GTCB) over a range of temperatures (77-95.25K). By matching the simulation results against the experimental data, we have found that the surface mediation is extended up to the fourth layer, rather than only the first as suggested by Kim and Steele, and the extent of this mediation is reduced with distance from the surface. This reinforces the important role of surface on the intermolecular ...

Energy Technology Data Exchange (ETDEWEB)

The biosorption characteristics of Pb(II) and Cd(II) ions from aqueous solution using the green alga (Ulva lactuca) biomass were investigated as a function of pH, biomass dosage, contact time, and temperature. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherm of the metal ions by U. lactuca biomass. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The monolayer biosorption capacity of U. lactuca biomass for Pb(II) and Cd(II) ions was found to be 34.7 mg/g and 29.2 mg/g, respectively. From the D-R isotherm model, the mean free energy was calculated as 10.4 kJ/mol for Pb(II) biosorption and 9.6 kJ/mol for Cd(II) biosorption, indicating that the biosorption of both metal ions was taken place by chemisorption. The calculated thermodynamic parameters ({delta}G{sup o}, {delta}H{sup o} and {delta}S{sup o}) showed that the biosorption of ...

International Nuclear Information System (INIS)

... Development Center, National Tsing-Hua University, Hsinchu, TW (China)

Energy Technology Data Exchange (ETDEWEB)

An improved process is disclosed for reducing the water content of coal containing bound water by releasing at least a portion of the bound water by maintaining the coal at a temperature from about 220/sup 0/ to about 500/sup 0/ F. in the presence of water at a pressure sufficient to maintain at least portion of the water in a liquid phase for a time sufficient to release at least a portion of the bound water wherein the improvement comprises contacting the coal during such treatment with an active material selected from the group consisting of carboxylic organic acids containing up to about 6 carbon atoms, phenol, phenolic acids and inorganic acids.

Science.gov (United States)

Jet Propulsion Laboratory. California Institute of Technology. Pasadena, California. Energy and Water Conservation. Steve Rigdon. Facilities Energy Manager ...

Energy Technology Data Exchange (ETDEWEB)

The water and steam circuits of steam generators in pressurized-water nuclear power plants are described together with the mechanism of denting, and the corrosion of spacer plates that leads to cracks in tubes by constriction. The different chemical specifications applicable to the water of the secondary circuit of the generators in normal operation and on first commissioning are listed. The results obtained and the measurements of chemical values taken in operation on the water in the secondary circuits of steam generators at Fessenheim and Bugey are presented.

International Nuclear Information System (INIS)

Cooling water is sprayed on the outer surface of an upper portion of a container, and a pool is formed by the cooling water flowing down while cooling the container. Further, the cooling water stored in the cooling water pool is recycled by a pump for spraying the cooling water on the outer surface of the upper portion of the container. Sufficient amount of cooling water is supplied for spraying the cooling water to the outer surface of the upper portion of the container so that the outer surface of the container is free from drying and a liquid membrane is formed on the entire surface. The amount of the cooling water is made greater than that of the cooling water evaporated when the entire amount of the heat generate in the reactor core of the reactor is transferred to the cooling ...

Science.gov (United States)

The thermodynamic characteristics of sorption of the isomeric tricyclo[5.2.1.02.6]decane (tetrahydrodicyclopentadiene, TDCPD) molecules were for the first time determined experimentally and by molecular statistical methods under the conditions of gas-adsorption chromatography on graphitized thermal carbon black and gas-liquid chromatography on stationary liquid phases of different polarities (Apiezon L and Carbowax 20M). The effects of the chemical nature of sorbents on the retention of the TDCPD isomers are considered. A procedure for calculating the thermodynamic characteristics of adsorption of molecules with a complex structure is suggested within the framework of the atom-atom approximation of the semiempirical molecular statistical theory of adsorption for the example of isostructural norbornane molecules. The procedure involves simultaneous variation of geometric parameters and refinement of the parameters that determine the special features of the ...

Energy Technology Data Exchange (ETDEWEB)

Petrographic research for the Nevada Nuclear Waste Storage Investigations focused on xenolithic variability in the Topopah Spring Member and on variations of clinoptilolite composition at Yucca Mountain. Zeolite and smectite occurrences were considered in terms of their relation to a disturbed zone beneath the potential repository, and mineral stability experiments have produced a new clinoptilolite structure as a result of prolonged heating at low temperature. Limitations were defined on the abundance of erionite and of sulfur. X-ray diffraction studies lead to improved analytical methods. Progress was made in the comparative study of mineralogy in sand ramps and in faults. Geological modeling considered the differences of the diffusion of nonsorbing tracers in vertically and in horizontally fractured rock. Modeling also treated the diffusion of a nonsorbing tracer in devitrified and in zeolitized rock. The results of these experiments in all cases show relatively symmetrical ...

International Nuclear Information System (INIS)

Ti-15Mo-2.7Nb-3Al-0.2Si (Timetal-21S), a metastable #beta#-titanium alloy, is a candidate material for titanium matrix composite structures in hydrogen-fueled hypersonic planes because of its excellent formability and adequate mechanical properties in the 500--800 C temperature range. The alloy is strengthened through the precipitation of fine #alpha# particles in the #beta# matrix. The mechanical properties and microstructures are controlled by a solutionizing/aging heat treatment. A major concern in using titanium alloys in hydrogen service is the embrittlement caused by the precipitation of hydrides. It is believed that the large solubility of hydrogen in the #beta#-phase would preclude the precipitation of hydrides in Beta titanium alloys, especially at low hydrogen pressures. However, depending on the hydrogen content, a shift in the ductile/brittle transition temperatures to levels much higher than room temperature has been reported for Timetal-21S alloy. The objective of the ...

Energy Technology Data Exchange (ETDEWEB)

Several inexpensive and non-toxic solvents with low vapour pressures were investigated for their suitability as alternative solvents for the absorption of carbon dioxide from flue gas. The solvents include poly(ethylene glycol)s, poly(ethylene glycol) ethers, poly(ethylenimine) and glycerol-based substances. Solvent properties such as thermal stability, solubility of carbon dioxide and selectivity over nitrogen were investigated in a systematic study using a thermogravimetric analyser. Absorption results are reported for pure carbon dioxide and nitrogen as well as a mixture of both gases. Desorption and long-term sorption behaviour are also discussed. Glycerol and poly(ethylene glycol)s show a high solubility of carbon dioxide. Due to the high viscosity of the solvent, carbon dioxide absorption in poly(ethylenimine) is very slow in spite of the presence of favourable amine groups. PEG 300 was found to be the best solvent in this study and shows a high carbon ...

Energy Technology Data Exchange (ETDEWEB)

The development and testing of novel control technologies and advanced adsorbent materials continue to be active areas of research. In the present study, Hg capture using adsorbent material derived from the bauxite residue (red mud) from two North American refineries was studied. The red mud, seawater-neutralised red mud, and acid-treated red mud were evaluated for their mercury adsorption capacity and compared with other, more conventional sorbent materials. Two different seawater-neutralised red mud (Bauxsol) samples were treated with HCl and HBr in an effort to increase the mercury sorption capacity. In all cases, the acid treatment resulted in a significant increase in the total surface area and an increase in the total pore volume. The fixed-bed mercury capture experimental results showed that the HBr activation treatment was very effective at increasing the mercury capture performance of both Bauxsol samples whereas the HCl treatment had no effect on the ...

Science.gov (United States)

The nature of extralattice aluminum and its effect on acidity in zeolites was studied. A series of zeolites (some commercial), dealuminated by various methods, were obtained having Si/Al ratios between 1.5 and 20. These were characterized using volumetric sorption, XRD, AA, NMR, and reaction studies. Samples dealuminated using ammonium hexafluorosilicate were found to contain little or no extralattice aluminum. In contrast, steam-dealuminated zeolites had large amounts of extralattice aluminum. In some cases a significant portion of the extralattice aluminum was unobservable by [sup 27]Al NMR, suggesting the existence of an aluminum species of low symmetry. Proton NMR indicated that all the protons were associated with the lattice aluminum atoms. Depending on the preparation history, different groups of H-Y zeolites exhibited different maxima in catalytic activity as a function of aluminum content. The maxima in catalytic activity for n-pentane cracking was found ...

Energy Technology Data Exchange (ETDEWEB)

Water-resources data for the 1993 water year for Texas are presented in four volumes, and consist of records of stage, discharge, and water quality of streams and canals; and stage, contents, and water quality of lakes and reservoirs; and water levels and water quality of ground-water wells. Volume 3 contains records for water discharge at 134 gaging stations; stage only at 1 gaging stations; stage and contents at 13 lakes and reservoirs; water quality at 81 gaging stations; and data for 30 partial-record and 4 flood-hydrograph partial-record stations. Also included are lists of discontinued surface-water discharge or stage-only stations and discontinued surface-water-quality stations; crest-stage and flood-hydrograph partial-record stations, reconnaissance ...

Wastenet

...Species - see CITES Trade of Dangerous Chemicals Transport and Environment U Urban Environment Use of natural resources V Volatile Organic Compounds W Waste Landfills Waste electrical and electronic equipment - see WEEE Waste incineration Waste legislation - reporting Waste management planning Waste oils Waste shipments Waste water - see Urban waste water Water Bathing Water Drinking water Floods Marine environment Urban waste water Water Framework Directive WEEE - Waste Electric and Electronic Equipment Wildlife ...

Energy Technology Data Exchange (ETDEWEB)

This procedure describes the formulation and make-up of Simulated Dilute Water (SOW), a low-ionic-content water to be used for Activity E-20-50, Long-Term Corrosion Studies. This water has an ionic content which is nominally a factor of ten higher than that of representative waters at or near Yucca Mountain. Representative waters were chosen as J-13 well water [Harrar, 1990] and perched water at Yucca Mountain [Glassley, 1996]. J-13 well water is obtained from ground water that is in contact with the Topopah Spring tuff, which is the repository horizon rock. The perched water is located in the Topopah Spring tuff, but below the repository horizon and above the water table. A nominal times ten higher ionic content was chosen to simulate the effect of ionic ...

International Nuclear Information System (INIS)

The research committee of the Atomic Energy Society of Japan on water chemistry standard aims at establishing the private standard of water chemistry of nuclear power plants. The committee gathers up 'BWR water chemistry management manual', 'PWR primary system water chemistry management manual' and 'PWR water chemical analysis standard method', and furthermore aims at the standardization of those in future. Looking back on the committee's activities for the past four years, latest results of research of water chemistry mainly contributing to safe and reliable nuclear power plants were described with the future perspective of water chemistry and a demanded break-through. (T.T.)

International Nuclear Information System (INIS)

In equipment industries, the equipments handling industrial water and pure water are numerous. In power generation including nuclear power generation, water serves as a working medium. Review is made on the experiences in the corrosion of iron and nickel base alloys in high temperature, high pressure water and the results of researches derived from them. Under high temperature and high pressure, carbon steel, low alloy steel, stainless steel and high nickel alloy cause corrosion even in pure water. But in the case of serious corrosion, chlorine, oxygen, alkali and others in water take part. The following matters are described: corrosion by steam; stress corrosion cracking in pure water; corrosion by impurities in high temperature, high pressure pure water, i.e. chlorine ions, dissolved oxygen, and alkali; corrosion under ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents a novel domestic hot water heater model to be used in a multi-objective demand side management program. The model incorporates both the thermal losses and the water usage to determine the temperature of the water in the tank. Water heater loads are extracted from household load data and then used to determine the household water usage patterns. The benefits of the model are: (1) the on/off state of the water heater and temperature of the water in the tank can be accurately predicted, and (2) it enables the development of water usage profiles so that users can be classified based on usage behaviour. As a result, the amount of ancillary services and peak shaving that can be achieved are accurately predictable and can be maximized without adversely affecting users. (author)

British Library Electronic Table of Contents (United Kingdom)

Indicators of source water use in different economic branches, water consumption in recycling and recycling-successive water supply in 1980?2006 are analyzed. Trends were identified in variations in specific water consumption in industry, agriculture, and municipal economy. Territorial differentiation of wetness indicators of regional product over federal districts and constituent territories of the RF is shown. Wetness values of gross domestic product in different economies are compared.

UK PubMed Central (United Kingdom)

Background Microbial water-quality indicators, in high concentrations in sewage, are used to determine whether water is safe for recreational purposes. Recently, the use of these indicators...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Before the implementation Water Framework directive, it was usual to forget that a good environment protection of the receiving waters needs a correct and coordinated operation of the subsystems of the water cycle, specially sewerage system, WWTP and receiving waters. This explains that most of the countries have focused their efforts in the treatment of dry weather flows forgetting the management of wet weather flows. Actually the idea that a sewerage system or a WWTP can not be planned or managed independently without considering the effects on the receiving waters is commonly accepted because not only each one of these systems must work correctly but also it is required a minimum impact in the receiving waters of the sewerage and WWTP overflows in dry and wet weather. All these links will affect the management strategy of the sewerage system (storm ...

UK PubMed Central (United Kingdom)

The effect of water stress on patterns of nitrate reductase activity in the leaves and nodules and on nitrogen fixation were investigated in Medicago sativa L. plants watered 1 week...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A model was developed to compute concentration of impurities in the WWER 440 steam generator (SG) secondary water along the tube bundle. Calculated values were verified by concentration values obtained from secondary water sample chemical analysis. (orig.). 2 refs.

UK PubMed Central (United Kingdom)

By the time of primary 21st century, water hyacinth had become a serious environmental problem in China. Water hyacinth contributes to the major part of ecological hazards from the invasion of foreign...Full Text Available

Science.gov (United States)

average bulk water temper ature rise, OF bulk water temperature at elevation z, OF bulk water temperature in channels 0 and 1, O F film temperature, OF ...

International Nuclear Information System (INIS)

Japanese (Jul 1976). Japan Kametani, Katsuaki Tomura, Kayoko . National

British Library Electronic Table of Contents (United Kingdom)

Fe-doped TiO2 hollow spheres (Fe-THs) were synthesized by sol?gel process using carbon spheres as templates. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV?vis diffuse reflectance spectrum (DRS), N2 adsorption?desorption isotherms, Electron paramagnetic resonance (EPR) spectroscopy and Photoluminescence emission spectroscopy (PL). UV?vis spectra showed that Fe3+ doping could extend the absorption edge to the visible region. EPR spectra showed that Fe3+ was incorporated into the crystal lattice of TiO2, which could inhibit the recombination of photo-induced electron?hole pairs and improve the photocatalytic activity. The photocatalytic activities of the prepared samples were evaluated for the degradation of dye Reactive Brillia...

Energy Technology Data Exchange (ETDEWEB)

This paper is an introduction course in modelling turbulent thermohydraulics, aimed at computational fluid dynamics users. No specific knowledge other than the Navier Stokes equations is required beforehand. Chapter I (which those who are not beginners can skip) provides basic ideas on turbulence physics and is taken up in a textbook prepared by the teaching team of the ENPC (Benque, Viollet). Chapter II describes turbulent viscosity type modelling and the 2k-{epsilon} two equations model. It provides details of the channel flow case and the boundary conditions. Chapter III describes the `standard` (R{sub ij}-{epsilon}) Reynolds tensions transport model and introduces more recent models called `feasible`. A second paper deals with heat transfer and the effects of gravity, and returns to the Reynolds stress transport model. (author). 37 refs.

Energy Technology Data Exchange (ETDEWEB)

A pump down model for a vacuum chamber with a reversibly adsorbed phase is presented. The outgassing equation which predicts the variation of coverage at the wall surface of a vacuum chamber with time is derived. Then the measured and the true outgassing rates are defined. The theoretical measured outgassing rate shows only a very weak dependence for pumping speed. This prediction is opposite to the experimental result that the measured outgassing rate depends significantly on pumping speed. It is discussed that the experimental measured outgassing rate must be described as the product of the effective pumping speed and the measured pressure in the pumped chamber, in which the measured pressure is equivalent to the equilibrium pressure of the wall surface described by the equilibrium adsorption isotherm as a function of the shifted surface coverage {theta}-{delta}{theta} by a small coverage {delta}{theta} from the coverage of a pumping point {delta}. (author)

British Library Electronic Table of Contents (United Kingdom)

Corrosion inhibition of iron in H2SO4 by polyacrylic acid (PAA) was investigated using electrochemical techniques at 30degreeC. Results obtained indicate that PAA inhibited the corrosion of iron in the acid medium. Inhibition efficiency increases with increase in PAA concentration and synergistically enhanced on addition of iodide ions. Potentiodynamic polarization results suggest that PAA functions as a modest cathodic inhibitor. The adsorption of PAA onto the iron surface followed Temkin adsorption isotherm. FTIR analysis revealed that the synergistic effect due to co-adsorption of iodide ions and PAA is co-operative in nature.

British Library Electronic Table of Contents (United Kingdom)

Abstract Young protostars embedded in circumstellar discs accrete from an angular momentum rich mass reservoir. Without some braking mechanism, all stars should be spinning at or near breakup velocity. In this paper, we perform simulations of the self-gravitational collapse of an isothermal cloud using the orion adaptive-mesh refinement code and investigate the role that gravitational torques might play in the spin-down of the dense central object. While magnetic effects likely dominate for low-mass stars, high-mass and Population III stars might be less well magnetized. We find that gravitational torques alone prevent the central object from spinning up to more than half of its breakup velocity, because higher rotation rates lead to bar-like deformations that enable efficient angular mome...

British Library Electronic Table of Contents (United Kingdom)

Many new technologies and approaches to the provision of comfort inside buildings such as displacement ventilation, mixed-mode strategies, personally controllable (task-ambient) designs, chilled beams as well as some old but recently fashionable ones such as natural ventilation are prompting a rethink of the accepted comfort wisdom. How can a single combination of thermal environmental parameters be deemed unacceptable in a conventional heating ventilation and air-conditioning setting, and yet be regarded as acceptable, or even pleasant, in a naturally ventilated or mixed-mode setting? Why do current comfort standards prescribe static and isothermal conditions for comfort in one building, and dynamic and spatially variable indoor climates for comfort in another? The phenomenon of alliesthe...

British Library Electronic Table of Contents (United Kingdom)

The removal of color from aquatic systems caused by presence of synthetic dyes is extremely important from the environmental viewpoint because most of these dyes are toxic, mutagenic and carcinogenic. In this present study, the yellow passion fruit (Passiflora edulis Sims. f. flavicarpa Degener) peel a powdered solid waste, was tested as an alternative low-cost adsorbent for the removal of a basic dye, methylene blue (MB), from aqueous solutions. Adsorption of MB onto this natural adsorbent was studied by batch adsorption isotherms at room temperature. The effects of shaking time and pH on adsorption capacity were studied. An alkaline pH was favorable for the adsorption of MB. The contact time required to obtain the maximum adsorption was 56h at 25degreeC. Yellow passion fruit peel may be ...

International Nuclear Information System (INIS)

The ternary rare earth compound NdRh_4B_4 has been studied by means of critical field, low temperature heat capacity, and static magnetic susceptibility measurements. Features in the upper critical field and heat capacity data at 1.31 K and 0.89 K suggest the occurrence of long-range magnetic order in the superconducting state. The temperature dependence of the static magnetic susceptibility follows a Curie-Weiss law with an effective magnetic moment #mu#sub(eff) = 3.58 +- 0.05 #mu#sub(B) and a Curie-Weiss temperature thetasub(p) = -6.2 +- 1.0 K between 20 K and room temperature. However, magnetization vs. applied magnetic field isotherms suggest the development of a ferromagnetic component in the Nd"3"+ magnetization at low temperatures. (author).

Energy Technology Data Exchange (ETDEWEB)

This document reproduces the final project of David San Fabian Ayuso, presented on May 26, 2005, for the obtention of the engineer degree of the Carlos III University of Madrid. A single-phase, isothermal model, including both electron and proton transport, is introduced for the simulation of polymer electrolyte fuel cells (PEM). The model is implemented in the commercial code Fluent 6.0, through the use of UDFs (User Defined Functions). In order to validate the model, a single canal of a PEM monocell is simulated in three dimensions. The obtained result are qualitatively satisfactory. It is observed that it is not essential to solve the current collectors when a monocell is considered (and not a stack). in the present study, the number of nodes is the computational grid appears to be too low in the membrane zone in order to make a complete validation of the model. (Author) 20 refs.

International Nuclear Information System (INIS)

A wood-polymer composite has been produced by impregnating the wood with the monomer and subsequently polymerizing it by exposure to a gamma radiation source. To compare the improvement in creep deformation of the wood due to the polymer impregnation, a nonlinear Norton-Bailey isothermal mathematical function has been used to model the bending creep deformation of the wood-polymer composites. Results show that the impregnation significantly improves the creep resistance of the wood. The maximum creep resistance is obtained when the amount of polymer impregnation exceeds about 30%. An interfacial interaction between the wood cell wall and the polymer could explain the creep deformation improvement, as well as the maximum impregnation level beyond which little improvement occurs. The results indicate that polymer impregnation is a viable method for improving the poor creep properties of wood. (author).

Energy Technology Data Exchange (ETDEWEB)

The temperature and concentration dependence of the kinetics of uranium(VI) ions adsorption onto activated charcoal from aqueous solutions has been studied. The adsorption proceeds via a rather fast stage followed by a slower one, with activation energies of 5.41 and 17.46 kJ . mol[sup -1] respectively. The diffusion of uranium ions into the pores of the activated charcoal controls the kinetics of adsorption which follows the Langmuir isotherm equation in the concentration range studied. The adsorption equilibrium constant k[sub c] has been derived at temperatures between 283 K and 323 K as well as [Delta] G, [Delta] H and [Delta] S. The results indicate that the adsorption of uranium ions on activated charcoal is an endothermic process. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Applications of magnesium alloys are motivated mainly by their lightweight. However, manufacturing cost should also be evaluated when considering applying them. From this point of consideration, adoption of sheet forming processes, which previously have not been heavily researched, should be an option. This paper is intended to pioneer the study of the formability of magnesium alloy AZ31 out of rolled sheets at elevated temperatures. The rolled microstructures are examined and correlated with their formability. Post-forming conditions will also be investigated. The tool employed to perform the sheet forming experiments was a punchless die-setting which used pressurized gas to press the sheet into a female die cavity. This technique applied to Mg-alloy is unconventional and warrants attention for its potential utilization in the industry. (orig.)

International Nuclear Information System (INIS)

Denting phenomenon as experienced in PWR steam generators has been investigated in the laboratory of Monel-400 tubes and C-steel baffles combination. Isothermal corrosion tests have been carried out by exposing capsules, containing a crevice between Monel-400 tubes and C-steel plugs, in plausible corrodents at 300"0C. Results indicated that the denting phenomenon is strongly influenced by the chloride content in the solution. In addition, it is a time dependent process. Stress exerted on the tubes by the growth of corrosion product on the outside surface of C-steel plugs are enough to deform the Monel tubes. The results have been discussed on the basis of accelerated corrosion of C-steel by hydrolyzable metal chlorides. (author).

International Nuclear Information System (INIS)

Interaction of Yb-Pd-Si system components is studied, isothermal cross section of this system state diagram at 870 K is constructed. Five new ternary silicides are detected in the system: YbPd_5Si_3, Yb_3Pd_2_0Si_6, YbPd_2Si, YbPd_0_,_6_7Si_1_,_3_3, YbPdSi; the existence of one more -YbPd_2Si_2, earlier known, is confirmed. Crystal structure for all the compounds detected is determined and examined. Data on the materials magnetic properties are obtained. It is assumed that YbPd_2Si, YbPd_2Si_2 and YbPdSi compounds appear to be the Condo-systems. 10 refs., 3 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

Results of strain controlled fatigue and tensile tests are presented for two nickel base solution hardened alloys which are reference structural alloys for use in several high temperature gas cooled reactor concepts. These alloys, Hastelloy X Inconel 617, were tested at temperatures ranging from room temperature to 871/sup 0/C in air and impure helium. Materials were tested in the solution annealed as well as in the pre-aged condition where aging consisted of isothermal exposure at one of several temperatures for periods of up to 20,000 h. Comparisons are also given between the strain controlled fatigue lives of these alloys and several other commonly used alloys all tested at 538/sup 0/C.

Energy Technology Data Exchange (ETDEWEB)

An x-ray diffraction technique for determining thin-film thickness is presented which should prove to be a valuable alternative to the array of spectroscopies (Rutherford backscattering spectrometry, Auger electron spectroscopy, etc.) currently favored for these measurements. Some of the virtues of this x-ray diffraction approach are its nondestructive nature, fast data acquisition rate (enabling in situ observations), thickness resolution better than 5 nm, and conventional equipment requirements. Results are shown for Pd/sub 2/Si thin films grown during isothermal annealing of Pd coatings (100 nm) on Si at 200 /sup 0/C for various amounts of time. A comparison of these x-ray measurements with Rutherford backscattering spectrometry data taken from the same specimens is used to demonstrate the validity of the x-ray technique.

Energy Technology Data Exchange (ETDEWEB)

In the paper presented, an attempt is made to describe quantitatively the room air motion by diffuse air distribution. Since solving the problem theoretically, seems to be hopeless at present, only an experimental solution seems to promise success. Experiments with diffuse air distribution offer suitable preconditions. With this kind of air introduction into the room, a relatively regular distribution of room air motion can be expected. A further simplification will be achieved by isotherme flow conditions. The first goal of the experiments was to establish whether the velocities measured are reproducible to demonstrate, and can be brought into a functional connection. The room air motion is a measured value which changes temporarily and locally quite largely, far more than is customary with technical measurements. From there, a second task arises, i.e. to evaluate the fluctuation of the velocity registered by its quantity in an appropriate measurement. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Increasing the end coking temperature to 850 C has a marked effect on both the physico-mechanical and physico-chemical properties of formed coke, and although subsequent rise in temperature leaves the mechanical strength largely unaltered, it appears to increase hardness, real density and conductivity at the expense of diminished reactivity. Formed coke strength can be slightly improved by extending the coking time by an isothermal residence period at end temperatures of 650 and 750 C. Structural change in the formed coke tends to concentrate in the 450 to 650 C range where carbon increases by 6.98-8.27% as compared with hydrogen and oxygen which fall 2.40-3.53 and 3.50-4.62% respectively.

British Library Electronic Table of Contents (United Kingdom)

The acid corrosion inhibition process of mild steel in 1M HCl by 1-butyl-3-methylimidazolium chlorides (BMIC) and 1-butyl-3-methylimidazolium hydrogen sulfate ([BMIM]HSO4) has been investigated using electrochemical impedance, potentiodynamic polarization and weight loss measurements. Potentiodynamic polarization studies indicate the studied inhibitors are mixed type inhibitors. For both inhibitors, the inhibition efficiency increased with increase in the concentration of the inhibitor and the effectiveness of the two inhibitors are in the order [BMIM]HSO4>BMIC. The adsorption of the inhibitors on mild steel surface obeyed the Langmuirs adsorption isotherm. The effect of temperature on the corrosion behavior in the presence of 5x10-3M of inhibitors was studied in the temperature range of 3...

International Nuclear Information System (INIS)

Deep level effects in GaAs MOSFET have been characterised in the ohmic channel using DLTS, low frequency excess noise and dispersion technique. An isothermal multi exponential curve fitting method has been devised and implanted into the DLTS system. Multi exponential curve fitting method used to decompose a multi exponential transient into its constituents so that the peak signature can be better characterised for the case whereas several peaks are closely spaced. Low frequency excess noise and dispersion techniques also confirm the trap in signature of the same traps observed in the DLTS measurements. (author)

International Nuclear Information System (INIS)

Preliminary observations on the isothermal carbon transfer in low-carbon Alloy-800 exposed in sodium with AISI-304 type of steel at 550_0 are reported. The alloy was found to undergo a carburization comparable or slightly lower than that observed for the AISI-304 stainless steel for carbon activities above 6 x 10 /sup -3/ at 550_0C, but was not found to decarburize below such a carbon activity value. In the examined range the chemical composition of the alloys does not affect the process out of the experimental uncertainty of measure. Conclusions concerning the effective diffusion for carbon in the alloy are formulated. Preliminary relationships were found for an empirical evaluation of the carburization of the Alloy-800 in sodium of known carbon activity.

British Library Electronic Table of Contents (United Kingdom)

In this context, the bulk ratio of CH4/N2 is examined as a potential alternative geochemical parameter for the assessment of thermal maturity of natural gas and compared to other previously published data. Open-system non-isothermal pyrolysis of low-mature coal from the Manjiaer sag, Tarim basin, yielded generation curves for methane and nitrogen. Analysis of the change of vitrinite reflectance indicates a two-stage process of thermal maturation with increasing temperatures. The relationship between Ro and pyrolysis temperature could be expressed by the following equations: Stage I: Ro = 0.0014T + 0.109, r = 0.9931(Ro Ro = 0.0067T -1.5855, r = 0.9996 (Ro > 0.6%). A kinetic interpretation of the characteristics of nitrogen and methane generation in humic coal during laboratory pyrolysis ind...

Energy Technology Data Exchange (ETDEWEB)

High temperature components of power plants are in many cases subjected to variable loading conditions such as cyclic creep or strain cycling. Therefore the cyclic behaviour of important heat resistant steels has been investigated under stress control and to a smaller extent under strain control. The behaviour under cyclic creep rupture conditions was determined in long term experiments covering a wide range of loading conditions. This behaviour can be described with the modified life fraction rule and a factor concept of relative life for single stage cycles and additionally with a multistep hypothesis for multi-stage cycles. The description can be adapted to estimate the life consumption under service type random conditions. The strain cycling behaviour was investigated in regard to the conditions of the heated surface of large components. To simulate this type of loading and to generate long term creep fatigue data, a service type strain cycle was developed. Anisothermal and ...

Energy Technology Data Exchange (ETDEWEB)

Although sulfur is present in many forms in kerosene, mercaptans are most objectionable due to their obnoxious odour and corrosive action. In this study, removal of one of the mercaptans has been reported, using red mud as an unconventional adsorbent. Red mud is a waste product from aluminium producing industries and has been used as an adsorbent for the removal of sulfur compounds as well as for other purposes. Adsorption studies described in this paper indicate that low concentration and high temperature favour the removal of 1-butanethiol from kerosene oil by adsorption on red mud. A first order mechanism has been proposed to describe the adsorption in the present system. Equilibrium data at different temperatures fit well in the Langmuir isotherm equation. Thermodynamic parameters for the present system indicate the feasibility of removal of 1-butanethiol from kerosene oil by adsorption on red mud. 10 refs., 4 figs. 3 tabs.,

International Nuclear Information System (INIS)

In a supercritical water-cooled reactor, property of water changes significantly around the critical point. It is expected that irradiation and change of water property will affect the chemistry and material corrosion. Deep understanding of interactions between supercritical water and materials under irradiation is important. However, comprehensive data on radiolysis, kinetics, corrosion and thermodynamics have not been obtained due to the severe experimental condition. To get such data by experiments and computer simulations, a national program funded by Ministry of Education, Culture, Sports, Science and Technology (MEXT) has been started since December 2002. (author)

International Nuclear Information System (INIS)

In this paper the diffusion of tritiated water vapor into concrete walls is studied to evaluate tritiated water retention capacity of a fusion reactor concrete building. Using a model of the tritiated water diffusion determined form experimental results, depth profiles of tritiated water in concrete are calculated in the case of being exposed to air containing tritiated water vapor during the normal operational condition of a fusion reactor. A 0.5-m-thick concrete is sufficient for reactor hall walls from a viewpoint of the tritium containment.

Science.gov (United States)

Water is one of our most precious resources. However, for many in the United States, having fresh, safe drinking water is taken for granted, and due to this perceived lack of relevance, students may not fully appreciate the luxury of having safe running water--in the home. One approach to resolving water-quality issues in the United States may reside in providing education that presents accurate information in a meaningful way. Accordingly, this article describes a unit designed to emphasize the importance of water-quality testing and purification and to introduce students to local water-quality issues. The engineering-based module of this eighth-grade science activity is particularly important due to the design-build-test component. (Contains 5 figures.)

Science.gov (United States)

... percent by interbasin ground-water flow into the Hueco Bolson, and 2 percent by flow into creeks and ... ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A single cylinder diesel engine study of water-in-diesel emulsions was conducted to investigate the effect of water emulsification on the engine performance and gases exhaust temperature. Emulsified Diesel fuels of 0, 5, 10, 15 and 20 water/diesel ratios by volume were used in a single cylinder, direct injection diesel engine, operating at 1200-3300 rpm. The results indicate that the addition of water in the form of emulsion improves combustion efficiency. The engine torque, power and brake thermal efficiency increase as the water percentage in the emulsion increases. The average increase in the brake thermal efficiency for 20% water emulsion is approximately 3.5% over the use of diesel for the engine speed range studied. The proper brake specific fuel consumption and gases exhaust temperature decrease as the percentage of water in the ...

Science.gov (United States)

Jun 16, 2011 ... Title: Chapter 21: Oceanographic Processes and Marine Productivity in Waters Offshore of Marbled Murrelet Breeding Habitat ...

Science.gov (United States)

_! Packaging, Cleanlines_, Preparation j Handling ..... 35. 'I. 40. WATER ................ , ......... Sterile, High Purity, Ethylene Glycol-Water Solutions. Requirement For . ...

British Library Electronic Table of Contents (United Kingdom)

Using air as a carrier gas is common in humidification?dehumidification desalination processes. A computer program was written using mass and energy balances for modeling the process behavior. The parameters considered in this work were inlet air and fresh water recycle temperatures, inlet air flow rate, saline water and fresh water recycle flow rates, and saline water to air flow ratio. Results of simulation showed that increasing inlet air and fresh water recycle flow rate increases fresh water production. It was also found that heating the inlet air to humidification column or cooling the inlet water to dehumidification column increases the production rate but increasing water to air flow ratio in a humidifier leads to a lower production rate. The predicted effects of the parameters on ...

Science.gov (United States)

metric temperatures has been prepared showing the surface water temper- ... occasion, gray levels show different densities for similar water temper- ...

Science.gov (United States)

Water Mites collected by Dr.Taiji Imamura...

UK PubMed Central (United Kingdom)

ObjectiveTo evaluate the effect of moderate aerobic physical activity in water on fetal cardiotocography patterns in sedentary pregnant women.MethodIn...Full Text Available

UK PubMed Central (United Kingdom)

An environmental study was done to examine the prevalence of Vibrio mimicus in some aquatic environments of Dhaka, Bangladesh, and of Okayama, Japan. Water samples from Dhaka environments and water...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

In the Mediterranean arc, vines for wine production are mainly grown without the support of irrigation. Under such conditions, site variables affecting the extent and seasonal timing of water deficits are the dominant environmental constraints for grape production. Moreover, water availability and vine water status are the factors most comprehensively determining fruit composition and, thus, wine quality. Therefore, monitoring the extent of water stress in vines might be a valuable tool for the optimisation of grape yield and quality. The objective of this study was to evaluate the feasibility of using the reflectance based Water Index (WI) to estimate vine water status at the leaf and canopy levels. The study was conducted on Vitis vinifera cv. Chardonnay potted plants submitted to contra...

UK PubMed Central (United Kingdom)

Halothane, chloroform, and carbon tetrachloride, in the vapor and liquid phases, stimulate the water receptor of the blowfly Phormia regina. There are three successive phases of response to long-lasting...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper, firstly, introduces the background in developing a high quality water supply system, in which the drinking water system is isolated inside a building. Results of questionnaire on the high quality service water are illustrated. The results of questionnaire have revealed that the high quality service water is extremely interested. Then, are described the target quality of high quality water, the constitution of high quality water supply system, the treatment process, the measures to secure safety and sanitary, and the method of maintenance. The high quality water is produced through the activated charcoal absorption treatment, membrane treatment, ozonation, cooling, mineral addition, and disinfection of city water. Furthermore, application examples of this system adopted to a department store and a bachelor ...