Science.gov (United States)

... Descriptors : *PROTECTIVE COATINGS, *WATER REPELLENTS, *COMBUSTIBLE CARTRIDGE CASES, COMPUTER PROGRAMS, SOLVENTS ...

Energy Technology Data Exchange (ETDEWEB)

Part of the crushed activated charcoal (about 20-50%) designed for manufacture of electrodes is made water repellant with the help of an aqueous suspension of water repelling agent containing 3-15% (preferably 10%) dry substance. After this the remaining part of the activated charcoal and the other additives are mixed with the water repelling part. The plates or tape which is rolled to an assigned thickness are pressed from the obtained mixture. The electrodes obtained by this method have a thin active layer and a porous structure and have good diffusion properties. They can be loaded by currents up to 80 mA/cm/sup 2/ without causing excessive polarization losses, and their service life is greater than or equal to 100 h.

International Nuclear Information System (INIS)

Water repellency en the microstructure super-hydrophobic cured surface is important for research and industrial purposes. This microstructure film can be cured on polyethylene terephthalate PET surface by electron beam (EB) at different irradiation doses 10-100 kGy. The microstructure formulation composed from hydrophobic acrylate oligomer (EB 244) and monomer (SR 440). The irradiation induced cross linking of the prepared microstructure was proved by FTIR spectroscopy and the adhesion force by abrasion test. Some factors affecting the adhesion force of the prepared microstructure film such as oligomer/monomer composition ratio and the thickness of the microstructure cured film were studied. The contact angles (8) were measured on cured surfaces before and after adding the super hydrophobic nanoparticles (Zonyl 9361). The super-hydrophobic cured surface showed the self-cleaning property. The volume of water droplet affected ...

Energy Technology Data Exchange (ETDEWEB)

From a macroscopic point of view, corrosion of Zn alloy coated steel sheet occurs by the coating preceding corrosion mechanism; microscopically, however, the coated layer corrosion velocity in the tip of corrosion is different. In order to find the main factors of under-film corrosion of Zn and Zn-Fe alloy coatings in the salt water spray atmospheric exposure test, the correlation between point inflation-exfoliation width and chlorine penetration behavior, point adhesion, and the difference in chlorine penetration behavior due to alloy coating components were investigated. Consequently, the following results were obtained: 1. The better correlation was observed between chlorine penetration distance and point inflation-point exfoliation width. 2. The durability of coating against chlorine penetration improved by increase in point adhesion and ...

Science.gov (United States)

This study investigated the effect of board type (unmodified vs. MAPE modified) on the surface quality and thickness swelling-water absorption properties of recycled high density polyethylene (HDPE) based wood plastic composites. Additionally, two commercially available coatings (cellulosic coating and polyurethane lacquer coating) were also applied to composite surfaces and their adhesion strength, abrasion and scratch resistance, and gloss values were determined. This study showed that modification of the composites with MAPE coupling agent increased the surface smoothness and reduced the water absorption and thickness swelling of the panels. Abrasion resistance of the composites was also improved through MAPE modification. Regardless of board type, higher scratch resistance and gloss values were observed for polyurethane lacquer coated samples compared to ...

British Library Electronic Table of Contents (United Kingdom)

A stable BSA blocking poly(dimethylsiloxane) (PDMS) microchannel was prepared based on in situ synthesized PDMS-gold nanoparticles composite films. The modified microchip could successfully suppress protein adsorption. The assembly was followed by contact angle, charge-coupled device (CCD) imaging, electroosmotic flow (EOF) measurements and electrophoretic separation methods. Contact angle measurements revealed the coated surface was hydrophilic, water contact angle for coated chips was 45.2^o compared to a water contact angle for native PDMS chips of 88.5^o. The coated microchips exhibited reproducible and stable EOF behavior. With FITC-labeled myoglobin incubation in the coated channel, no fluorescence was observed with CCD image, and the protein exhibited good electrophoretic effect in ...

Energy Technology Data Exchange (ETDEWEB)

Several types of coatings have previously been visually identified on the surface of 105-K East and 105-K West Basins fuel elements. One type of coating (found only in K West Basin) in particular was found to be a thick translucent material that was often seen to be dislodged from the elements as flakes when the elements were handled during visual examinations (Pitner 1997). Subsequently it was determined (for one element only in a hot cell) that this material, in the dry condition, could easily be removed from the element using a scraping tool. The coating was identified as Al(OH){sub 3} through X-ray diffraction (XRD) analyses and to be approximately 60 {micro}m thick via scanning electron microscopy (SEM). However, brushing under water in the basin using numerous mechanical strokes failed to satisfactorily remove these coatings in their thickest form as judged by appearance. Such ...

Science.gov (United States)

The cause of the Gulf War Syndrome may be related to soldiers being exposed to insecticides (e.g., permethrin (P)), insect repellents (e.g., N,N-diethyl-m-toluamide (DEET)), an organophosphate nerve agent simulant (e.g., diisopropyl fluorpohosphate (DFP)), and/or prophylactic treatment (e.g., pyridostigmine bromide (PB)) against potential nerve gas attacks. The purpose of this study was to assess the dermal disposition of [14C]permethrin in ethanol or ethanol:water (3:2) in the isolated perfused porcine skin flap (IPPSF) model with simultaneous dermal exposure to DEET or DFP. These IPPSFs were also simultaneously perfused arterially with or without PB, DFP, or DFP + PB. The results indicated that DFP + PB significantly increased [14C]permethrin absorption compared to controls (1.06% dose vs 0.14% dose). PB significantly increased [14C]permethrin disposition in the stratum corneum (SC) in aqueous mixtures only (9.40 vs 3.35% dose), while topical ...

British Library Electronic Table of Contents (United Kingdom)

In this study, the effects of channel surface wettability, cross-sectional geometry and orientation on the two-phase flow in parallel gas channels of proton exchange membrane fuel cells (PEMFCs) are investigated. Ex situ experiments were conducted in flow channels with three different surface wettability (hydrophilically coated, uncoated, and hydrophobically coated), three cross-sectional geometries (rectangular, sinusoidal and trapezoidal), and two orientations (vertical and horizontal). Flow pattern map, individual channel flow variation due to maldistribution, pressure drop and flow visualization images were used to analyze the two-phase flow characteristics. It is found that hydrophilically coated gas channels are advantageous over uncoated or slightly hydrophobic channels regarding un...

Energy Technology Data Exchange (ETDEWEB)

This book presents the papers given at a conference on offshore platforms. Topics considered in this book include risk assessment, crack propagation, fracture control, stress corrosion, the reliability of pile foundations, the thermal conductivity of offshore pipeline coating material, economic analysis, hydrodynamics, simulation, Arctic structure design, composite materials, buoys, deep water drilling, corrosion protection, pollution control equipment, and subsea exhaust gas compressors.

Energy Technology Data Exchange (ETDEWEB)

Stable strange quark matter produced in the QCD phase transition in the early universe will trap neutrons and repel protons, thus reducing primordial helium production, Ysub(p). For reasonable values of Ysub(p), the radius of strange droplets must exceed 10/sup 6/ cm if strange matter shall solve the dark-matter problem without spoiling Big Bang helium synthesis. (orig.).

J-STORE (Japan)

Full Text Available

International Science & Technology Center (ISTC)

Multi-functional Bioactive Nano-structured Coatings for Load-Bearing Implants

International Science & Technology Center (ISTC)

Characterization and Testing of Coated Nickel- and Iron-Based Superalloys for Application in High-Temperature Power Installations

Energy Technology Data Exchange (ETDEWEB)

It is necessary to identify those measurable soil parameters which dictate the severity of the corrosion problem for coated irons and steels. When this is done, meaningful accelerated aging tests can be designed to validate the reduced corrosion rate for the planned coating. The following discussion introduces the important concepts and measurement parameters in the (a) design of accelerated aging tests, and (b) evaluation of the planned installation site for corrosion potential. Certain combinations of soil oxidation reduction potential (ORP) or electric potential (Eh), acidity (pH), fertilizer, water table, and soil hydraulic conductivity can result in severe corrosion of buried steel/iron vessels. If there are power lines nearby, additional loss of vessel material to the soil will occur. These factors are discussed.

Energy Technology Data Exchange (ETDEWEB)

Superparamagnetic MFe{sub 2}{sup 3+}O{sub 4} (M=Mn{sup 2+}, Fe{sup 2+} and Co{sup 2+}) inverse spinel ferrite (ISF) nanoparticles with narrow size distribution having average diameters of 6-8 nm were synthesized by a diol reduction of organic metals and the surface was modified to be hydrophilic by coating with succimer. Magnetic resonance imaging (MRI) contrast enhancement by dipolar coupling defined interactions between the synthesized ISFs and protons in the bulk water was investigated with initial susceptibility, magnetization and anisotropy of the succimer-coated ISFs. The relaxivity ratios, r{sub 2}/r{sub 1}, for MnFe{sub 2}O{sub 4}, Fe{sub 3}O{sub 4} and CoFe{sub 2}O{sub 4} were measured to be 12.2, 23.1 and 62.3, respectively, which demonstrate the potential usefulness of these magnetic nanoparticles as T{sub 2} contrast agents for MRI.

International Nuclear Information System (INIS)

The main compositions of iron-base amorphous self-fluxing alloy powders of 150 mesh, used in this work, are Fe, Cr, Ni, W, Mo, B, Si and C. The ranges of each element in at% are (65-70)Fe, (3-5)Cr, (2-4)Ni, (2-4)W, (1-2)Mo, (10-14)B, (4-7)Si and (2-3)C. The atomic ratio of metal-metalloid is about 80:20, so this alloy is abbreviated as M_8_0X_2_0. The material on which coatings were deposited is 1020 steel, austenitized for 1h at 880 C, water quenched, and tempered at 180 C for 1h. This heat treatment resulted in a low carbon martensite structure with a hardness of HRC35-45. After cleaning, shot blasting and preheating the steel to about 200 C, the authors sprayed a thin Ni-Al alloy layer of about 0.1--0.15mm in thickness onto the specimen by means of an oxygen-acetylene torch to provide better bonding of the coating with substrate. Then the M_8_0X_2_0 and M_8_0X_2_0+8%CeO_2 alloy coatings were sprayed ...

Energy Technology Data Exchange (ETDEWEB)

In this paper coating developments for advanced gas turbine engines (diffusion aluminide coatings, overlay coatings, and ceramic thermal barrier coatings) were desorbed, a selection of current metallic coatings was made and their performance as outlined. Finally coating developments for advanced diesel engines with a view to improved turbocharging or to low heat rejection engines (adiabatic diesel concept) were dealt with. (IHOE).

Energy Technology Data Exchange (ETDEWEB)

A hose lining process, used widely for underground service structures, such as for city gas, and water and sewerage pipes, was adopted to repair interiors of underground wire raceways, and improvements were made for power cable pipe use, including long size construction, inner diameter assurance, and flame retardation. The sealing hose as a lining material consists of a fabric layer woven by warps of polybutylene terephthalate (PBT) and wefts of combined PBT fibers and glassfibers, the fabric being coated with polyurethane resin on one side. The other side of the fabric is coated with heat hardening resin made of epoxy resin as the main ingredient and aromatic amine as the hardening agent to assure close adhesion of the sealing hose onto the pipe interior. Mimic raceways were used to verify the lining material for its abrasion coefficient, mechanical strength, wear resistance, water cut-off performance, ...

Energy Technology Data Exchange (ETDEWEB)

Papers are presented under 38 symposia. Subjects included reinforced concrete, protective coatings and linings, cathodic/anodic protection, chemical cleaning of boilers, managing corrosion with plastics, water treatment, HRSG boiler tube failure analysis, corrosion in oil and gas production, corrosion in petroleum refining and gas, processing, pipelines and tanks, high temperature materials, chemical process industry, aerospace equipment, materials technology developments for incinerators and waste fuel-fired processors, materials and corrosion in fossil-fuels conversion and combustion, corrosion in nuclear systems, marine corrosion, building systems, corrosion mechanisms, corrosion inhibitors and corrosion monitoring and measurement.

Energy Technology Data Exchange (ETDEWEB)

To improve adherent properties of electrogalvanized steel (EGS) to polymeric topcoats, the surfaces of EGS were modified by polyelectrolyte-modified zinc phosphating solution. The electrochemical reaction between phosphating solution and EGS led to the complete coverage with fully grown hopeite crystals after only 5 sec treatment, thereby improving adhesion to topcoating and providing protection of EGS against corrosion. To evaluate the ability of polyphenylene sulfide (PPS) polyaryl thermoplastic coatings to protect zinc phosphate (Zn{center_dot}Ph)treated steels from corrosion in a wet, harsh environment ( 1.0 wt % H{sub 2}SO{sub 4}, 3.0 wt % NaCl and 96.0 wt % water at temperatures from 25{degrees} to 200{degree}C), we exposed them in an autoclave to attempt heating-cooling cyclic fatigue tests (1 cycle = 12 hr at 200{degrees}C + 12 hr at 25{degrees}C) up to 90 times. The major chemical reaction at the interface between the PPS and Zn in the ...

Scientific Electronic Library Online (English)

Abstract in english We consider the three dimensional electromagnetic inverse scattering problem of determining information about a buried coated object from a knowledge of the electric and magnetic fields measured on the surface of the earth corresponding to time harmonic electric dipoles as incident fields. We assume that the buried object is a perfect conductor that is (possibly) partially coated by a thin dielectric layer. No a priori assumption is made on the extent of the coating, i.e. (more) the object can be fully coated, partially coated or not coated at all. We present an algorithm based on the linear sampling method and reciprocity gap functional for reconstructing the shape of the scattering obstacle together with an estimate of the surface impedance of the coating.

Energy Technology Data Exchange (ETDEWEB)

The photocatalyzed degradation of pyridine in the gas phase was investigated using titanium dioxide semiconductor supported on mordenite. The complete mineralization was found to occur over a catalyst containing 75 wt% TiO{sub 2} and 25 wt% mordenite in about 180 min in the presence of saturated water vapor at O{degrees}C (4.6 Torr). Low water vapor pressure of 0.096 Torr was found to be sufficient to achieve a reasonably high percentage and rate of degradation. Diffusion of pyridine within the catalyst adversely affects the activity when the thickness of the catalyst coating exceeds the penetration depth of illumination. The activity of the zeolite-supported catalysts was higher than that of TiO{sub 2}. The photonic efficiency for the complete mineralization of pyridine to CO{sub 2} was determined to be 0.48. 29 refs., 6 refs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

In vitro cytocompatibility and cellular interactions of lauric acid and dextran-coated magnetite nanoparticles were evaluated with two different cell lines (mouse fibroblast and human cervical carcinoma). Lauric acid-coated magnetite nanoparticles were less cytocompatible than dextran-coated magnetite nanoparticles and cellular uptake of lauric acid-coated magnetic nanoparticles was more than that of dextran-coated magnetite nanoparticles. Lesser cytocompatibility and higher uptake of lauric acid-coated magnetite nanoparticles as compared to dextran-coated magnetic nanoparticles may be due to different cellular interactions by coating material. Thus, coating plays an important role in modulation of biocompatibility and cellular interaction of magnetic nanoparticles.

Energy Technology Data Exchange (ETDEWEB)

Olive field is oil productive from a thin stratigraphically trapped sandstone within the Upper Cretaceous lower Tuscaloosa Formation. The discovery of Olive in 1981 led to renewed interest in the Mid-Dip Tuscaloosa Trend that continues today. Discovery and development was based on the correlation of the B sandstone to a mappable soft seismic event at a depth of 10,500 ft. The field was developed by 25 wells on 40-acre spacing. Olive has been waterflooded since 1983 and is a target for enhanced recovery using carbon dioxide. A total of 7.5 million stock tank bbl or approximately 75% of the original oil in place is estimated to be recoverable by conventional and enhanced recovery methods. The B sandstone was deposited by a northwest to southeast-flowing high-sinuosity meandering river system. Point bar, channel, and channel abandonment deposits are present. The point bar formed from the lateral migration of the river system from west to east, and channel abandonment is evident at the ...

Energy Technology Data Exchange (ETDEWEB)

A cryocondensation pump was designed for the baffle chamber of General Atomics DIII-D tokamak and will be installed in the fall of 1992. The purpose of the pump is to study plasma density control by pumping the divertor. The pump is toroidally continuous, approximately 10 m long and located in the lower outer corner of the vacuum chamber of the machine. It consists of a 1 m{sup 2} liquid helium-cooled surface surrounded by a liquid nitrogen-cooled shield to limit the heat load on the helium-cooled surface. The liquid nitrogen-cooled surface is surrounded by a radiation/particle shield to prevent energetic particles from impacting and releasing condensed water molecules. A thermal enhancement coating was applied to the nitrogen shell to lower the maximum temperature of the shell. The coating is non-continuous to keep the toroidal electrical resistance high. The whole pump is supported off the ...

Energy Technology Data Exchange (ETDEWEB)

A chromium-free conversion coating for magnesium alloys were described. The conversion coating could be obtained when AZ31D magnesium alloy was immersed in a solution containing a manganese salt, phosphate and an inhibitor. Corrosion resistance of the chemical conversion coating was evaluated by anodizing polarization curve and salt immersion. XRD analysis showed that the conversion coating was mainly composed of Mn{sub 3}(PO{sub 4}){sub 2}. The morphology of the coating is observed by using SEM. The effect of electrolyte pH and concentration of inhibitor on coating growth are investigated. (orig.)

International Nuclear Information System (INIS)

Technology of plasma sputtering, structure and properties of zirconium dioxide coatings were studied. Necessity of void number increase to enhance coating heat-resistance is shown. Optimal powder particle size (20-60 #mu#m) providing optimal coating porosity was determined. Weight part of stabilizating oxide (Y_2O_3) in ZrO_2 for formation in coating of microcracks serving as barriers for macro-cracks propagation was determined.

International Nuclear Information System (INIS)

Decommissioning of radiological and nuclear installations is for this century the new challenge. One of the performance criteria is the reduction of total quantities of radioactive materials (liquid or solid) arising from dismantling and decontamination of radiological and nuclear installations. In this work we present a new application of the water soluble polymers used as: - flocculation agents in treatment and conditioning process within the management of radioactive liquid materials; - strippable coatings on solid materials based on the water soluble polymers. The parameters of water soluble polymers made in our Institute by radiation processing have been analysed, namely the molecular average weight, composition, and efficiency of utilization of these polymeric materials as well as the content of ash, additives, decontamination factor, consumption per surfaces/liter, corrosion aspects, ...

Science.gov (United States)

The commercial solid phase microextraction (SPME) fibers are not stable enough in organic solvent and tend to swell and strip off from the silica fiber in the high performance liquid chromatography (HPLC) mobile phase, and therefore the application of SPME coupled online with HPLC is limited. In this study, an SPME fiber coated with single walled carbon nanotubes (SWCNTs), prepared by means of electrophoretic deposition, was coupled on line to HPLC for the determination of four endocrine-disrupting compounds, i.e. bisphenol A (BPA), estrone (E(1)), 17?-ethynylestradiol (EE(2)) and octylphenol (OP), in aqueous samples. The results showed that the SWCNTs coating on the prepared fiber did not swell and strip off from the platinum fiber throughout the experiment, thus indicating a high resistance to the HPLC mobile phase, the mixture of water and acetonitrile. The SWCNTs fiber had similar (for OP) or higher (for BPA, EE(2) and ...

Science.gov (United States)

The growth of an oxide interfacial layer was recently found to increase the open-circuit voltage (OCV) and efficiency by up to 60 per cent in GaAs metal-semiconductor solar cells. Details of oxidation techniques to provide the necessary oxide thickness and chemical structure and using ozone, water-vapor-saturated oxygen, or oxygen gas discharges are described, as well as apparent crystallographic orientation effects. Preliminary results of the oxide chemistry obtained from X-ray, photoelectron spectroscopy are given. Ratios of arsenic oxide to gallium oxide of unity or less seem to be preferable. Samples with the highest OVC predominantly have As(+3) in the arsenic oxide rather than As(+5). A major difficulty at this time is a reduction in OCV by 100-200 mV when the antireflection coating is vacuum deposited.

British Library Electronic Table of Contents (United Kingdom)

Chitosan (Ch) microspheres have been developed by precipitation method, cross-linked with glutaraldehyde and used as a template for layer-by-layer (LBL) deposition of two natural polyelectrolytes. Using a LBL methodology, Ch microspheres were alternately coated with hyaluronic acid (HA) and Ch under mild conditions. The roughness of the Ch-based crosslinked microspheres was characterized by atomic force microscopy (AFM). Morphological characterization was performed by environmental scanning electron microscopy (ESEM), scanning electron microscopy (SEM) and stereolight microscopy. The swelling behaviour of the microspheres demonstrated that the ones with more bilayers presented the highest water uptake and the uncoated cross-linked Ch microspheres showed the lowest uptake capability. Micros...

British Library Electronic Table of Contents (United Kingdom)

Nanocapsules coated by medicinal plants have many applications in drug manufacturing. Medicinal plants can be loaded on nanocapsules with polyesteric triblock copolymer poly ethylene glycol-poly butylene adipate-poly ethylene glycol (PEG-PBA-PEG) as shell and olive oil can be introduced as a core of nanocapsules by a method known as polymer deposition solvent evaporation method. In this research, first, certain amount of polymer, Matricaria recutita extract and olive oil were mixed with acetone and then, water was added to the solution using magnetic stirrer. After which the acetone was removed by vacuuming and finally nanocapsules were found by freezing-drier. The study showed the size of nanocapsules depends on variety of factors such as the ratio of polymer to oil and concentration of p...

International Nuclear Information System (INIS)

Water-based epoxy sealants were examined during a 2-year period to determine their effectiveness as barriers to radon release in uranium mines. Radon emanation rates from uranium ore samples were monitored for extended periods in the laboratory before and after sealant application. Reduction of radon flux due to the coating of lab samples was approximately 80 percent. Test chambers in a dormant uranium mine were monitored to determine both short and long-term barrier effectiveness. These field studies of the sealants indicated reductions greater than 50 percent relatively soon after application and nearly 75 percent more than 1 year later. An unexpected complication to early monitoring in the form of a large radon emanation increase, believed due to added moisture, is discussed.

Science.gov (United States)

An investigation was conducted to determine the cause of coating residue found in the test gun chambers during qualification firing of 120-mm combustible cartridge case (CCC) ammunition for the MlAl/A2 main battle tank. The CCC is coated with a clear epox...

British Library Electronic Table of Contents (United Kingdom)

The purpose of this study is to investigate the influence of tungsten carbide/carbon (WC/C) coating on the surface durability of casehardened steel gear. Two kinds of WC/C coatings were deposited on the ground gear pair made of chromium molybdenum steel with carburizing and quenching. One is the conventional WC/C coating, and the other is WC/C coating with about 1 ?m CrN interlayer. Here, the WC/C-coated test pinion and the WC/C-coated one with CrN interlayer are represented by WT and ST, respectively. Non-coated test pinion is represented by NT. The surface roughness along the tooth profile direction of WT and ST was almost the same as that of NT. A spur gear test was carried out with an IAE power circulating type gear test rig under EP gear oil lubricating condition. The fatal failure mo...

Science.gov (United States)

... Accession Number : ADA544419. Title : Omental Lipid-Coated Mesh. Descriptive Note : Final rept. 1 Jul 2009-16 Jun 2011. ...

British Library Electronic Table of Contents (United Kingdom)

Ceramic coatings with high emission were fabricated on Ti6Al4V alloy by microarc oxidation (MAO) with additive FeSO4 into the electrolyte. The microstructure, chemical composition and chemical state of the coatings were determined by SEM, XRD, EDS and XPS, respectively. The bonding strength between the coating and substrate was studied by tensile strength test, together with the thermal shock resistance of the coating. The results showed that Fe content in the coating layer significantly affect its thermal emissivity. The relative content of Fe in the coatings surface increased at first and then decreased with increasing the concentration of FeSO4 in electrolytes, so does the emissivity of the coatings. The bonding strength became weaker with increasing the concentration of FeSO4. In addit...

International Science & Technology Center (ISTC)

Hard Nano-Strutural Coatings Resistant to the Extreme Conditions of Chemical, Abrasive and High Energy Media for Thermonuclear Power, Oil and Gas and Chemical Industries

Science.gov (United States)

... Accession Number : ADA954164. Title : Electron Diffraction Examination of Gun Barrel Coatings. Descriptive Note : Special rept.,. ...

British Library Electronic Table of Contents (United Kingdom)

In this study two surface sensitive methods, i.e. quartz crystal microbalance with dissipation monitoring (QCM-D) and ellipsometry, were used for erosion measurements of a rosin-based marine antifouling paint binder. Thin films of the binder were applied on sensor surfaces by the means of spin-coating and the effect of water velocity over the paint film, water temperature or ionic strength on erosion was investigated. Both the acoustic QCM-D model and the optical ellipsometry model gave comparable erosion results. The initial 2-50nm rapid erosion of the top layer was followed by steady-state erosion rate until end of experiment. For example, the steady-state erosion rate was 12nm/24h in artificial seawater at 23degreeC and with a flow of 200ml/min over the paint surface as measured with QC...

International Science & Technology Center (ISTC)

The New Titanium Alloys With Increased Mechanical Properties and Corrosion Resistance for Medical Instruments and their Coatings

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Aluminum hydroxide coating thicknesses were measured on fuel elements stored in aluminum canisters in K West Basin using specially developed eddy current probes . The results were used to estimate coating inventories for MCO fuel,loading. Brushing tests successfully demonstrated the ability to remove the coating if deemed necessary prior to MCO loading.

Energy Technology Data Exchange (ETDEWEB)

The Ti and Ti-Al coatings were deposited onto hot-worked AISI H11 steel substrates and plasma nitrided at 900 C. The Ti coated samples were successfully nitrided, while cracking and delamination of the Ti-Al coating was observed during nitriding. The formation of [delta]-TiN and [epsilon]-Ti[sub 2]N phases were detected after plasma nitriding of the Ti coating. During plasma treatment of the Ti-Al coating, the initial Ti[sub 3]Al and Al phases were paartially transformed into TiAl phase. The martensite transformation of the substrate material was found. The as-deposited Ti coating has a fibrous structure, while the structure of the as-sputtered Ti-Al coating is columnar. The superficial Vickers microhardness of plasma-nitrided Ti coating was 2200 HV 0.03 and the critical load of higher than 50 N indicates very good ...

International Nuclear Information System (INIS)

In situ spectroscopic ellipsometry was employed to investigate the initial regime of rare earth metal (REM) conversion coatings formation on AZ31 magnesium alloy. Three REM salts solutions, 0.05 mol.dm"-"3 Ce(NO_3)_3, La(NO)_3 and Sm(NO)_3 solutions, were used for REM conversion coatings preparation. By deconvoluting the ellipsometric data, the surface of the fresh well-polished AZ31 magnesium alloy was found to be covered with 15.80 nm thick native (hydr)oxide film; the refractive indices and the thickness of Ce, La and Sm conversion coatings were obtained. The formation kinetics of three REM coatings follows different exponential functions and the coatings exhibit different optical properties. La conversion coating has the largest n values and the lowest k values while Sm conversion coating is just opposite. Moreover, the pH variation of ...

Energy Technology Data Exchange (ETDEWEB)

For the protection of buried steel pipeline, it is common practice to coat the pipelines with highly insulating coating and apply a cathodic current to insulate the pipe from the aggressive environment. Cathodic current protects holidays or damaged area of coating which required less current than would be needed for an uncoated pipe, but because of the cathodic reactions evolution will be taken H{sub 2} and OH{sup -} on holidays which exposed metal to the environment place. This effect is to cause loss bond of coating around the holidays called cathodic dis-bonding. In this paper we measured cathodic dis-bonding of three types of coatings at - 1.5 V(Cu/CuSO{sub 4}) according to ASTM G8. We studied on cathodic dis-bonding resistance of petroleum-base, coal tar-base and polyethylene plastic tape coatings. After 30 days immersion in electrolyte it was found that ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the effects of SiC coating on the oxidation resistance of C/C composites in combusting fields, which are expected to be applied to high temperature structural materials at over 1770K. The coating methods employed were CVD and pack cementation. The time changes in weight loss of the specimens were measured at temperatures of 1770K and 1900K under the equivalence ratio of 0.9 generated by methane-air combustion, and the surface of the specimens before and after the experiment was observed by SEM. Although the weight loss of the specimens coated by the CVD method was minimal, the coating layer was easily peeled off from the substrate. On the other hand, the layer of the specimens coated by the pack cementation method was stable and adhered to the substrate, but the substrate was degraded because of penetration of oxygen through the pores in the layer. To cover the ...

International Nuclear Information System (INIS)

By means of an audio frequency plasma polymerisation ultra-thin gradient plasma polymer layers were deposited on zinc and zinc-coated iron. The aim was to generate an interfacial polymeric layer which bonds to an oxidised metal as well as to a subsequently applied organic coating and acts as an interfacial barrier layer for ions and water. Surface modifications were done in an in situ plasma cell with infrared reflection absorption spectroscopy (IRRAS). The zinc surface was first activated by an oxygen plasma to provide a freshly oxidised and contamination free oxide surface. The intermediate stages of the surface reactions could be revealed. Carbon dioxide molecules as oxidation products adsorbed on the growing zinc oxide and were desorbed at a later stage. An organosilicon plasma polymer was deposited directly on top of the oxide layer from a hexamethyldisilane (HMDS) plasma. Afterwards a cyclohexene ...

Energy Technology Data Exchange (ETDEWEB)

This article described a full-scale green renovation project undertaken by a construction management firm in Newton, Massachusetts. Chapman Construction and Design began renovating its own office building in late 2007 and completed it in September 2008. The firm set out to achieve LEED Platinum certification from the United States Green Building Council. The project involved energy saving modifications to its mechanical systems; replacing plumbing fixtures with high efficiency alternatives to reduce water consumption by at least 40 per cent; installing skylights and additional windows to allow more natural light into the interior space; salvaging doors, lighting, metal studs and masonry whenever possible; and using sustainable products such as recyclable carpets, tiles and low-VOC paint. The main feature of the renovation was a new 47 kW (DC) photovoltaic (PV) solar power array installed on the rooftop. The PV array includes 208 panels and a SunPower SPR-225 system ...

International Nuclear Information System (INIS)

In this paper, the influence of plasma nitriding at temperature 720 deg. C for 20 h on the surface microstructure and interface microstructure of electroplated chromium coating was investigated. In these conditions, interdiffusion, mixing and reaction phenomena of elements originating from the substrate and coating material are more likely to occur, thus increasing the bonding strength between the coating and carbon steel substrate. The change of the structures from the substrate side to the coating surface, and the effect of the substrate steel on the interface structure were studied by cross-sectional transmission electron microscope observation (XTEM). The nitride layer formed on the surface was analyzed by X-ray diffraction method (XRD). After treatment at above conditions a 6-7 #mu#m thick nitride compound layer was formed in surface region and the same thick carbide compound layer was also formed ...

British Library Electronic Table of Contents (United Kingdom)

In situ composite coating of hydroxyapatite (HA)/TiO2 were produced on titanium (Ti) substrate by micro-arc oxidation coupled with electrophoretic deposition (MAO&EPD) technique with different concentrations of HA particles in the 0.2M NaOH electrolyte solution. The surface morphology and chemical composition of the hybrid coating were effected by HA concentration. The amount of HA particles incorporated into coating layer increased with increasing HA concentration used in the electrolyte solution. The corrosion behavior of the coating layer in simulated body fluids (SBF) was evaluated using a potentiodynamic polarization test. The corrosion resistance of the coated sample was increased compared to the untreated Ti sample. The in vitro bioactivity assessment showed that the MAO&EPD treated...

British Library Electronic Table of Contents (United Kingdom)

Assembly of icosahedral capsids of proper size and symmetry is not understood. Residue F170 in bacteriophage P22 coat protein is critical for conformational switching during assembly. Substitutions at this site cause assembly of tubes of hexamerically arranged coat protein. Intragenic suppressors of the ts phenotype of F170A and F170K coat protein mutants were isolated. Suppressors were repeatedly found in the coat protein telokin-like domain at position 285, which caused coat protein to assemble into petite procapsids and capsids. Petite capsid assembly strongly correlated to the side chain volume of the substituted amino acid. We hypothesize that larger side chains at position 285 torque the telokin-like domain, changing flexibility of the subunit and intercapsomer contacts. Thus, a sing...

Energy Technology Data Exchange (ETDEWEB)

The goal of this work was to develop a process flow diagram to economically produce a clean-burning fuel from fine Illinois coal. To accomplish this, the process of pelletizing fine coal with calcium hydroxide, a sulfur capturing sorbent, was investigated. Carbonation, which is the reaction of calcium hydroxide with carbon dioxide (in the presence of moisture) to produce a bonding matrix of calcium carbonate, was investigated as a method for improving pellet quality and reducing binder costs. Proper moisture level is critical to allow the reaction to occur. If too much moisture is present in a pellet, the pore spaces are filled and carbon dioxide must diffuse through the water to reach the calcium hydroxide and react. This severely slows or stops the reaction. The ideal situation is when there is just enough moisture to coat the calcium hydroxide allowing for the reaction to proceed. The process has been successfully demonstrated on a ...

Science.gov (United States)

AbstractOBJECTIVETo provide an overview of the 2009 edition of the Rourke Baby Record (RBR), which incorporates recent research in the literature relating to preventive health care for children aged 0 to 5 years.QUALITY OF EVIDENCERecommendations are identified as supported by good, fair, or consensus evidence, according to the classification of the Canadian Task Force on Preventive Health Care.MAIN MESSAGENew information and recommendations are given for growth monitoring, nutrition, developmental surveillance, physical examination maneuvers, immunization schedules, and advice for parents. Anticipatory guidance updates relate to injury prevention, infant swaddling, literacy facilitation, nonparental child care, parenting skills programs, serum lead levels, over-the-counter cough and cold medications, pacifiers, antipyretics, insect repellents, and dental care and oral health. The 2009 RBR is available in English and French in both National and Ontario versions and ...

International Nuclear Information System (INIS)

Several metallurgical coatings have been developed that provide good tribological performances in high-temperature liquid sodium and that are relatively unaffected by neutron fluences to 6 X 10/sup 22/ n/cm/sup 2/ (E > 0.1 MeV). The coatings that have consistently provided the best tribological performance have been the nickel aluminide diffusion coatings created by the pack cementation process, chromium carbide or Tribaloy 700 trade mark (a nickel-base hardfacing alloy) applied by the detonation-gun process, and chromium carbide and other hardfacing alloy) applied by the detonation-gun process, and chromium carbide and other hardfacing materials applied by the electro-spark deposition process. The latter process is a relatively recent development for nuclear applications and is expected to find wide usage. Other coating processes, such as plasma-spray coating, sputtering, and ...

Energy Technology Data Exchange (ETDEWEB)

Duplex-coating procedures consisting of plasma nitriding and Me-C:H hard coating lead to an improved performance of the devices because the Me-C:H coating is supported by the nitrided phase and, therefore, the `eggshell-effect` is avoided. Furthermore, this support leads to a higher load-bearing capacity of the thin film. Two standard procedures (classical high-pressure plasma nitriding and unbalanced magnetron sputtering of Ti-C:H) were performed subsequently to prepare the duplex coatings on X20Cr13 ferritic stainless steel. The corrosion resistance of the steel could be improved by nitriding at 450 C compared to the untreated ferritic substrate. The roughness is determined by the nitriding step. The weakest point of the coating is the transition zone between the nitrided and the untreated substrate and not the interface between the Ti-C:H coating and the ...

International Nuclear Information System (INIS)

The industrial radiation processing using low energy electron beam (EB) accelerators lower than 300 keV offers high speed, safe technologies for the chemical conversion of thin layer coatings. Because of the nonselective mode of initiating chain reaction polymerization involving free radicals in synthetic coating layers and suitable substrates, the EB curing of the coatings on woods and papers has particular advantage. Hungary decided to start an up-to-date EB line to process cement-bound (CB) wood chipboards with pigmented acrylic coatings. The CB wood chipboards contain more than 60 % of portland cement and up to 40 % of wood particles. They are produced as large boads of 6 - 16 mm thickness. In their fireproof character and other aspects, they are similar to asbestos-cement boards without containing carcinagenic asbestos, and are stable against moisture and atmospheric influences. EB-cured acrylate ...

UK PubMed Central (United Kingdom)

Computer-assisted analysis revealed a striking sequence similarity between the putative 24-kDa protein (p24) encoded by open reading frame (ORF) 5 of beet yellows closterovirus and the coat protein...Full Text Available

International Nuclear Information System (INIS)

New data about the structure of high-temperature resistant metalloceramic plasma sprayed coatings in micro and nano areas are presented. Application of the new instrumental methods: transmission electron microscopy combined with selected area electron diffraction mode is possible to obtain these data. The first layer in Ni based metallic bond coat shows nanocrystalline structure. External ceramic layer based on stabilised ZrO_2 is polycrystalline and contains both cubic and tetragonal crystalline phases. Local inhomogeneities in coatings phase composition are determined. (author)

Science.gov (United States)

... The data were transformed into total hemispherical emittance values and correlated with respect to ceramic coating thickness and temperature ...

Energy Technology Data Exchange (ETDEWEB)

There is increasing demand to functionalize meso- and nano-porous materials by coating and make the porous substrate biocompatible or environment friendly. However, coating on a meso-porous substrate poses great challenges, especially if the pore aspect ratio is high. In the current work the pulsed laser deposition (PLD) method is used for coating Ni{sub 3}Al-based meso-porous membranes with diamond-like carbon (DLC) layers of high thickness homogeneity and adhesion. (orig.)

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

With the deposition of PVD hard coatings on the tools applied in machining operations it is possible to achieve significant improvements in the performance and quality of the machining processes. Depending on the machined material and the operating principle, e.g. turning, milling or drilling, not only different machining parameters but also different coating materials are necessary. In interrupted cut machining of tempered steel, for example, the life time of Ti-C-N coated inserts is several times greater than the Ti-C-N coated ones. This is a result of the favourable thermophysical and tribological properties of Ti-N-C. The potential for tool protection by CrN coatings is a result of the high ductility and low internal stress of this coating materials. CrN films can be deposited with greater film thickness, still maintaining very good adhesion. This paper ...

International Nuclear Information System (INIS)

The cathodic vacuum arc provides a means of producing large currents of positive ions of a wide variety of materials. These ions can be utilized to produce coatings with improved properties such as higher density and adhesion. The processing is particularly useful in reactive deposition of ceramic coatings having excellent stoichiometry. In this review, emerging aspects of the technology are emphasized.

International Nuclear Information System (INIS)

An improved coating for Advanced Gas Cooled Nuclear Reactor austenitic stainless steel fuel cans is described which, tests have shown, inhibits the deposition of carbon on the cans in carbon-containing ionising radiation environments. The coating comprises a refractory oxide which has been prepared by a vapour phase condensation method, in combination with a noble metal. (U.K.).

International Nuclear Information System (INIS)

Tungsten (W) coating on fusion candidate V-4Cr-4Ti (NIFS-HEAT-2) substrate was demonstrated with plasma spray process for the purpose of applying to protection of the plasma facing surface of a fusion blanket. Increase in plasma input power and temperature of the substrate was effective to reduce porosity of the coating, but resulted in hardening of the substrate and degradation of impact property at 77 K. The hardening seemed to be due to contamination with gaseous impurities and deformation by thermal stress during the coating process. Since all the samples showed good ductility at room temperature, further heating seems to be acceptable for the vanadium substrate. The fracture stress of the W coating was estimated from bending tests as at least 313 MPa, which well exceeds the design stress for the vanadium structure in fusion blanket. (author)

Energy Technology Data Exchange (ETDEWEB)

The effect of the coated composite surface of particles on the mechanical properties of the powder bed was investigated. Polyethylene-silica surface composite powder was prepared at several coating ratios with Hybridizer. Various tests on mechanical properties of the powder bed were carried out with the prepared powder, and the following results were obtained: The ultimate tensile strength depends only on the cohesive force between particles, and the contact probability model of composite particles led to good agreement between the experimental and calculated values. The coefficient of internal friction and cohesive shear strength were influenced due to the interlocking effect of the surface roughness of composite particles. The effects of coating particles became small with dynamic properties like angle of repose. It is possible to control the mechanical properties in a step wise fashion by changing the ...

British Library Electronic Table of Contents (United Kingdom)

Analysis reproducibility and detection sensitivity of capillary electrophoresis (CE) are often questioned by applied scientists, which has hindered its application as a routine method. To address these issues, a simple, precise, and reproducible dynamic coating method was developed by applying carboxymethyl chitosan (CMC) dynamic coating on fused silica capillary. The proposed coating was accomplished by simply rinsing the capillary with CMC solution for 1?min in between runs, with no regeneration procedure or buffer additives needed. Electroosmotic flow could be well controlled by adjusting the pH of background electrolyte, and the adsorption of analytes onto the capillary inner wall was effectively eliminated. The main parameters of the coating condition were optimized, and extensive app...

Energy Technology Data Exchange (ETDEWEB)

Ion storage CeO{sub 2} and CeO{sub 2}/SnO{sub 2} coatings were prepared by sol-gel dip-coating method using aqueous-based process. The influence of added SnO{sub 2} in the CeO{sub 2} oxide coatings on the inserted/extracted charge was determined by chronocoulometric measurements. It was found that for 60 nm thick film the inserted/extracted charge was twice larger (Q = 10mC/cm{sup 2}) for films containing 17 mol % SnO{sub 2} if compared to pure CeO{sub 2}. The addition of SnO{sub 2} to the mixed oxides coatings on their optical properties and structural characteristics were studied.

British Library Electronic Table of Contents (United Kingdom)

The determination of residual stress (RS) in case-hardened steel gear truck synchronisers coated with thermal sprayed molybdenum was carried out using neutron and synchrotron X-ray diffraction. Two samples with different coating thicknesses (about 120 ?m and 1.4 mm) and different steel substrates (16MnCr5 and SAE4140, respectively) were investigated. Microanalysis revealed substantial porosity in both samples and some debonding was observed between the thin coating and the substrate. The bulk hardness of the SAE 4140 proved to be much higher than the 16MnCr5 and the surface case-hardening increased it by a further 20%. The full three-dimensional stress depth-profile was determined by neutron diffraction (ND) in both the coatings and the substrates, while synchrotron radiation allowed a dep...

British Library Electronic Table of Contents (United Kingdom)

Abstract Introduction.- Infection is the worst complication seen with inflatable penile prosthesis (IPP). Both the American Medical Systems (AMS) and Coloplast IPP have infection retardant coatings. AMS is coated at the factory with rifampicin and minocycline (InhibiZone). The Coloplast IPP has a hydrophilic coating covalently bonded to its components that will absorb any aqueous solution before implantation and provides increased surface lubricity to decrease bacterial adherence. Aim.- We tested several antibiotic dips comparing zones of inhibition (ZOI) against five commonly infecting bacteria with coated Coloplast implants. Results were compared with those ZOI created with strips of an AMS IPP precoated with InhibiZone. Methods.- Pieces of sterile Coloplast Titan IPP were dipped in (i) ...

British Library Electronic Table of Contents (United Kingdom)

The combined processes of plasma nitriding and cathodic arc deposition of (Ti,Cr,Nb)CN coatings were applied to HSS substrates. The nitrided layers, obtained in a mixture of H2 (70%) and N2 (30%) at two different temperatures (480^oC and 510^oC), were examined for the microhardness depth profiles. Characterization of the duplex coatings was performed by investigating elemental and phase composition, texture, hardness, friction and wear. XRD and XPS analyses revealed the formation of a mixture of a carbonitride fcc solid solution, in a dominant proportion, and metallic chromium. The film hardness was measured to be ~34GPa. The duplex (Ti,Cr,Nb)CN coatings exhibited superior tribological behavior as compared to both nitrided layers and non-duplex coatings.

British Library Electronic Table of Contents (United Kingdom)

A Ni3Al coating was prepared by plasma spraying technique on the surface of titanium alloy. Ni-Al mixed powders, coatings and reaction products were investigated by scanning electron microscope, EDS, DSC and XRD. A tight bonding between the coating and the substrate was formed. The X-ray diffraction analysis of the patterns showed that the coating not only had Ni3Al phase, but also had NiO and Al2O3 phase microcontent. Comparing Ni coated Al to Ni3Al at 900^oC, the diffusion was stronger and the diffusion layer was thicker. A minute pore structure was formed at 1200^oC in the front edge of solid-state reaction layer. So Ni3Al restrained the solid-state reaction of the coating with the substrate, and as a whole weakened the entry of oxygen atoms into the substrate and quenched the out-diffu...

Energy Technology Data Exchange (ETDEWEB)

There is presently considerable interest in wear resistant coatings produced using closed field unbalanced magnetron sputtering technology. For example, layered films of diamond-like carbon (DLC) with tungsten or titanium additions have been widely reported. The benefit is that the mechanical properties are enhanced (e.g. giving greater toughness); also it is possible to control the stress state and enhance adhesion. Here we report the further development of this concept by the addition of TiN, TiCN and TiC layers in DLC-based composites, utilizing an additional source of electrons in the vicinity of substrate to enhance ionisation of the plasma and increase coating density. Composite coatings of ceramics TiN, TiC{sub x}N{sub y}, TiC, CrN, TiCrN, TiCrCN, TiCrC, metal doped Ti{sub x%}-DLC and their combinations were deposited on 316 stainless steel substrates. The mass flow of reactive gases into the chamber was controlled ...

International Nuclear Information System (INIS)

Research highlights: The dental implant of titanium could be modified by anodic oxidation. It was found that incorporation of strontium ions into the matrix increase the bone formation. In this study, we try to investigate the effect of corrosion property and bioactivity on coatings containing strontium by anodic oxidation. The results suggest that coatings containing strontium on titanium by anodic oxidation has the potential to show the stability and bioactivity in the clinical use. - Abstract: Pure titanium (Ti) and titanium alloys are considered as bio-inert materials in clinical use. Bioactivity is the ability to induce bone-like apatite on the material surface. The micro-arc oxidation (MAO) technique is an effective method for improving the surface properties of titanium. The aim of this study was to investigate the bioactivity and corrosion behavior of MAO coatings containing strontium, which is beneficial for ...

Energy Technology Data Exchange (ETDEWEB)

Titanium alloys are characterized by poor tribological properties, and the traditional use of titanium alloys has been restricted to nontribological applications. The deposition of a well adherent diamond coating is a promising way to solve this problem. In this study, the tribological properties of diamond-coated titanium were studied using a pin-on-disk tribometer, and the results were compared with those of pure titanium and plasma nitrided titanium. The tribological behavior of pure titanium was characterized by high coefficient of friction and rapid wear of materials. Plasma nitriding improved the wear resistance only under low normal load; however, this hardened layer was not efficient in improving the wear resistance and the friction properties under high normal load. Diamond coating on pure titanium improved the wear resistance of titanium significantly. Surface profilometry measurement indicated that little or no ...

Energy Technology Data Exchange (ETDEWEB)

Today, as a result of increase in oil prices, limited fossil fuel resources, environmental consideration and global warming, the methyl ester fuels have been focused on alternative fuels. Methyl ester fuels can be used more efficiently in low heat rejection engines (LHR), in which the temperature of combustion chamber is increased by creating a thermal barrier. In this study, the piston, cylinder head, exhaust and inlet valves of a diesel engine were coated with the ceramic material Al{sub 2}O{sub 3}-TiO{sub 2} by the plasma spray method. Thus, a thermal barrier was provided for the parts of the combustion chamber with these coatings. The effects of corn oil methyl ester that produced by the transesterification method, and No. D2 fuels' performance and exhaust emissions' rate were studied by using equal in every respect coated and uncoated engines. Tests were performed on the uncoated engine, and then ...

International Nuclear Information System (INIS)

The photon rupture method, by which oxide film and metal are removed by focused pulsed Nd-YAG laser beam irradiation, was applied to form artificial micro-pits in Zn-5 mass% Al alloy-coated steel. The zinc alloy-coated layer was removed by pulsed laser irradiation treatment for about one second in a neutral buffer solution with NaCl. The rest potential transient with the laser treatment was measured. In the early stage of the laser treatment the rest potential of zinc alloy-coated steel changed to the negative direction immediately after every irradiation of a laser pulse and then returned to the previous value. However, after the steel substrate was exposed to the solution, the rest potential moved to the positive direction immediately after every irradiation of a laser pulse and then returned to the previous value. The amplitude and duration of the potential change after the laser irradiation increased with repetition of ...

Energy Technology Data Exchange (ETDEWEB)

Lower cost painting flock-like in appearance and touch feeling was developed as a new surface softening method for automobile interior plastic molded parts. The base coat with the same color as piles mixed into a top coat was first painted on the surface of a plastic molded part after cleaning, and after the top coat with less pitch mixed with piles was painted on the wet base coat and dried by a heater, excess piles were removed with suction and air blowing to produce flock-like appearance. Nylon 66 of 0.4mm in length was used as piles, and mixed into the top coat by 8.0wt% in content. This painting method was applicable to even such parts as one with a complex configuration, and one impossible to set piles on it by conventional methods because of poor durability. As a certain amount of piles with different colors were mixed into the top coat, sprinkly colored ...

International Nuclear Information System (INIS)

The authors describe measurements of emittance made on samples of solar cell coverglasses incorporating new coatings both on C-7940 fused silica and on CMX ceria doped microsheet. Samples of a conventional, MgF_2 coating on the same two types of coverglass substrates were included in the measurements as controls. Measurements were made by the calorimetric method of total hemispherical emittance within a cooled chamber as well as by the more common infrared reflectance method. Emittance enhancements from 1 to 4% were measured for the new coatings.

Energy Technology Data Exchange (ETDEWEB)

Electron paramagnetic resonance was used to investigate surface-coated magnetite-based magnetic fluids doped with TEMPOL. Two magnetic fluid samples, having magnetite nanoparticles with average diameter of 94 A and coated with different coating layers (lauric acid plus ethoxylated polyalcohol in one case and oleoylsarcosine in the other case), were doped with TEMPOL (6 mM and pH 7.4) and investigated as a function of the nanoparticle concentration. The resonance field and the resonance linewidth both scale linearly with the nanoparticle concentration.

Energy Technology Data Exchange (ETDEWEB)

Performance and emissions data were gathered on a normally aspirated single cylinder DI engine with various combinations of ceramic coatings installed. Thin ceramic thermal barrier coatings were applied to the piston crown and bowl, the head and valves, and the cylinder liner. The coated piston and head were run singly and in combination with the cylinder liner to investigate the effects of these different coated surfaces on emissions and performance. Coating the piston crown alone results in generally lower cylinder pressure, lower brake specific fuel consumption and lower NO(x) emission compared to the baseline engine. Soot emission is typically increased below 2000 RPM and decreased above 2000 RPM. Coating the head alone reduces cylinder pressure, but generally increases specific fuel consumption and NO(x) and soot emission. The KIVA-II code was used to model ...

Science.gov (United States)

... 31. New electric forming methods offer potentials for light metals; magnetic forming and plasma forming. ... 3, 25 Magnetic Forming ..... ...

Science.gov (United States)

COATINGS FOR THE METAL-SEMICONDUCTOR SOLAR CELLS 3S GIVEN. THIS METHOD UTILIZES THE MEASURED EQUIVALENT INDEX OF. REFRACTION OBTAINED FROM ELLIPSOMETRY ...

Energy Technology Data Exchange (ETDEWEB)

The main purpose of solid or fluid lubricants in ball-bearings is to separate the balls and races from contacting each other in so-called asperity collisions. Steel to steel contacts lead to microwelds which roughen functional rolling-contacting surfaces and deteriorate the lubricant. By using balls with a ceramic TiC coating, two goals are achieved. First, there are fewer asperity collisions because of the extreme smoothness of the high precision polished TiC coated balls. Second, if collisions do occur, there is practically no microwelding taking place, leaving the surfaces and the lubricant in good condition. Examples are given where the bearing lifetime is increased up to 10 times if the steel balls are replaced by TiC-coated balls. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The refractory nature and high ductility of body centered cubic (bcc) phase tantalum makes it a suitable material for corrosion- and wear-resistant coatings on surfaces which are subjected to high stresses and harsh chemical and erosive environments. Sputter deposition can produce thick tantalum films but is prone to forming the brittle tetragonal beta phase of this material. Efforts aimed at forming thick bcc phase tantalum coatings in both flat plate and cylindrical geometries by high-rate triode sputtering methods are discussed. In addition to substrate temperature, the bcc-to-beta phase ratio in sputtered tantalum coatings is shown to be sensitive to other substrate surface effects.

British Library Electronic Table of Contents (United Kingdom)

Herein, we demonstrate the structure of the PS colloidal crystals which were fabricated on the hydrophilic/hydrophobic Si wafers by a spin-coating technique. Monodisperse PS colloids are spin-coated onto self-assembled monolayers of 3-(aminopropyl)triethoxysilane and propyltrimethoxysilane coated Si wafers. PS spheres organized as ordered close-packed face-centered cubic structure with (111) planes on the hydrophilic surface while they gathered without the crystal structure on the hydrophobic surface. This paper also reports a simple and rapid method to fabricate the close-packed structure of hollow TiO2 spheres. The colloidal crystal of TiO2 hollow spheres was prepared using the PS sphere template on the hydrophobic surface. The mechanism for the growing multilayers of self-assembled PS p...

British Library Electronic Table of Contents (United Kingdom)

Ni-Co/SiC nanocomposite coatings were electrodeposited in a modified watt type of Ni-Co bath containing 20nm SiC particles to be codeposited. Potentiodynamic polarization tests were conducted to study the effect of the SiC particulates on the electrodeposition of Ni and Co. Scanning electron microscopy was used to assess the morphology of the Ni-Co alloy and Ni-Co/SiC nanocomposite coatings. The distribution of the particulates in the matrix was considered by means of transmission electron microscopy. Applying nanomechanical testing instruments coupled to atomic force microscopy, mechanical properties of the alloy and composite coatings were studied and compared. The presence of 11vol.% SiC in the Ni-Co matrix increased hardness more than 60%. The average depth of scratch in the mentioned ...

Energy Technology Data Exchange (ETDEWEB)

TiB{sub 2} appears to be a promising material for the wear protection in various tribological systems, e.g. the diecasting of Al. This study focuses on the development of titanium boride coatings deposited by PACVD, a deposition method which is most suitable for the coating of substrates with complex shapes. All layers analysed are very smooth and exhibit a quasi-amorphous fracture surface. XRD and TEM analysis indicate a nanocrystalline structure with grain sizes in the order of 2 nm. The diffraction patterns can well be correlated to titanium diboride. WDS reveals an over stoichiometric B/Ti ratio. The layer hardness reaches the value of 33 GPa and the critical load in scratch tests rises to 35 N. Neither 100Cr6 nor Al as a counterpart in pin-on-disk tests leads to wear of the coating. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Corrosion behavior of deposition coated specimens prepared by the technique proposed by the authors is investigated in salt immersion tests, and also those of pure magnesium, 3N, 4N and 6N grades, and magnesium alloys, AZ31 and AZ91E, are investigated for comparison. Inhomogeneous corrosion occurs in AZ31 and AZ91E alloys when buffered solutions with pH values of 6.5 and 9.0 including 1% NaCl and a conventional 3% NaCl solution are used for immersion tests, while 6N-Mg shows homogeneous corrosion in such solutions. Corrosion behavior of the deposition coated specimen resembles that of 6N-Mg. Purification process included in the deposition coating technique provides homogeneity in microstructural and electrochemical terms, which results in improving corrosion resistance. (orig.)

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Micron-size Ni-base alloy (NBA) powders were mixed with both 1.5 wt.% (hereinafter %) micron-size CeO{sub 2} (m-CeO{sub 2}) and also 1.5% and 3.0% nano-size CeO{sub 2} (n- CeO{sub 2}) powders. These mixtures were coated on low-carbon steel (Q235) by 2.0 kW CO{sub 2} laser cladding. The effects on the microstructures, phases and electrochemical corrosion of the coatings upon the addition of m- and n- CeO{sub 2} powders to NBA (m- and n- CeO{sub 2} /NBA) have been investigated. The results showed that a smooth coating was prepared under suitable processing parameters (P= 2.0 kW, V= 180 mm min{sup -1}) by adding 1.5% n- CeO{sub 2}. In addition to the primary phases of {gamma}-Ni, Cr{sub 23} C{sub 6} and Ni{sub 3} B in the Ni-base alloy coating, CeNi{sub 3} was formed in Ni-base alloy coatings with both n- CeO{sub 2} and m-CeO{sub 2} particles, and CeNi{sub 5} appeared in the ...

International Nuclear Information System (INIS)

High concentrations of Cs-137 were detected in the muscles of Walleye Pollack (Theragra chalcogramm) collected from Kitamiyamato banks (sampling on 25 Jul. 2000), Kamui area (16 Oct. 2000) and Niigata coasts (31 Jan. 2001). The concentrations were 0.35 #+-# 0.01, 0.41 #+-# 0.01, and 0.63 #+-# 0.02 Bq/kg-wet, respectively. The average concentration in our past investigations was about 0.25 #+-# 0.01 Bq/kg-wet. Samples from other areas, the coat of Kushiro (8 May 2001), North Tishima (13 Nov. 2000) and the Sea of Okhotsk (6 May 2001), had the average concentrations. There were no such high concentrations of Cs-137 in other fish species collected from Kitamiyamato banks, Kamui area, and Niigata coasts. Fish samples with high concentrations all make the migration in the north of Japan sea. These results would indicated that samples took in Cs-137 elements from sea-water or foods on the migration route. Cs-137 concentrations in muscles of walleye ...

Energy Technology Data Exchange (ETDEWEB)

Fusion energy is one of only a few truly long-term energy options. Since its inception in the 1950s, the vision of the fusion energy research program has been to develop a viable means of harnessing the virtually unlimited energy stored in the nuclei of light atoms--the primary fuel deuterium is present as one part in 6,500 of all hydrogen. This vision grew out of the recognition that the immense power radiated by the sun is fueled by nuclear fusion in its hot core. Such high temperatures are a prerequisite for driving significant fusion reactions. The fascinating fourth state of matter at high temperatures is known as plasma. It is only in this fourth state of matter that the nuclei of two light atoms can fuse, releasing the excess energy that was needed to separately bind each of the original two nuclei. Because the nuclei of atoms carry a net positive electric charge, they repel each other. Hydrogenic nuclei, such as deuterium and tritium, must be heated to ...

Energy Technology Data Exchange (ETDEWEB)

The high temperature abrasive wear resistant of the composites with different Al{sub 2}O{sub 3} volume fractions, particle coating and size were investigated and the failure action of composites under different conditions at high temperature was analyzed. The results showed that the high temperature abrasive wear resistant of composite with Ni coating and wide size and 39% volume fraction of particle is the best among all composites examined. (orig.)

International Nuclear Information System (INIS)

This rebuttal to a previous article provides new insight into the use of sprayed sealants in uranium mines. The author rejects the idea that the value of rock sealant on radon control is destroyed by changes in barometric pressure, showing that this is not necessarily true. The analyses described demonstrate that radon contamination resulting from changing barometric pressures is reduced by a rock coating. The overall use of coatings depends on their costs and effectiveness as compared with other radon control measures. 6 refs.

International Nuclear Information System (INIS)

A super-hydrophobic coating was prepared by combining a rigid base film with crater-like hemispherical holes and acicular nanoparticles. The acicular boehmite powder provides a high contact angle on the film surface. The rigid base film with crater-like hemispherical holes inhibits the rapid decrease of contact angle by surface rubbing. The combination of different roughness is an effective method for improving the abrasion resistance of super-hydrophobic films.

Energy Technology Data Exchange (ETDEWEB)

Thin solid films of CeO[sub 2] and mixed CeO[sub 2]-TiO[sub 2] were prepared by the sol-gel route via the dip-coating technique. Particulate sols of ceria were made from inorganic ((NH[sub 4])[sub 2]Ce(NO[sub 3])[sub 6]) precursor which were used for preparation of CeO[sub 2] thin solid films while CeO[sub 2]-TiO[sub 2] coatings have been made by using mixed organic-inorganic (Ti(OiPr)[sub 4] and CeCl[sub 3].7H[sub 2]O) precursors. The solar transmission values (T[sub s]) of both coatings are in the range 0.6-0.8 and depend on coating thickness. Cyclic voltammetric (CV) measurements show that the CeO[sub 2]/LiOH system exhibits higher overall electrochemical reversibility when compared to the CeO[sub 2]-TiO[sub 2]/LiOH system. The CeO[sub 2]/LiOH system is also less sensitive with regard to the coating thickness. Coulometric measurements show that CeO[sub 2] exhibits a larger ...

Energy Technology Data Exchange (ETDEWEB)

A portable fiber optic detector that senses the presence of specific target chemicals by electrostatically attracting the target chemical to an aromatic compound coating on an optical fiber. Attaching the target chemical to the coated fiber reduces the fluorescence so that a photon sensing detector records the reduced light level and activates an appropriate alarm or indicator.

Energy Technology Data Exchange (ETDEWEB)

Coatings and sensors having both steric and chemical selectivity. Controlled porosity provides the steric selectivity, whereas chemically tailored film properties, using controlled composition or modification by coupling agents, chemical species replacement, or chemical species within pores, provide the chemical selectivity. Single or multiple layers may be provided.

Energy Technology Data Exchange (ETDEWEB)

An industrial EB processing line is started to produce cement-bound /CB/ chipboard with radiation cured acrylic coating. The basic features of this line are presented here. The main technological parameters of coating such as: effect of oligomer- and monomer reactivity, monomer functionality, dose-rate and inerting atmosphere on the progress of curing have been discussed. The EB processed CB board is an advanced composite material for the modern lightweight architecture.

Energy Technology Data Exchange (ETDEWEB)

In this work a comprehensive metallophysical study was carried out for two aluminosilicide slip coatings of the systems Al-Si and Al-Nb-Si and an electron-beam Co-Cr-Al-Y coating on alloy EP-539 (17...19% Cr, 4...6% Co, 2.5...4% W, 4.5...6.5% Mo, 2...3% Ti, 3...4% Al, 1.4...2% Nb, balance Ni) after high-temperature testing. The protective properties of the coatings were evaluated from the results of laboratory tests for heat resistance at 1000/sup 0/C in the combustion products of diesel fuel with added sulfur at 970, 1000, and 1060/sup 0/C for 100 h and after full-scale tests for 150, 250, 400, and 700 h. Metallographic, hardness, x-ray, and micro x-ray studies of the coating were carried out. Layer-by-layer phase composition and the lattice spacing of the main phases were determined. X-ray analysis was carried out in an a DRON-1 diffractometer in copper K/sub ..-->../-radiation, and x-ray ...

Energy Technology Data Exchange (ETDEWEB)

This paper introduces a new method to produce nano-composite powder for the preparation of high performance ZnO varistors. ZnO particles were coated with Bi{sub 2}O{sub 3}, Sb{sub 2}O{sub 3}, Co{sub 2}O{sub 3}, Cr{sub 2}O{sub 3} and other additives via liquid nano-coating technique. Then the prepared powder was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermal gravity and differential scanning calorimetry (TG-DSC) and particle size distribution. The results showed that the ZnO composite powder is homogeneously coated and ultrafine. The densification, phase composition and microstructure of ZnO varistors was studied by linear shrinkage, X-ray diffraction (XRD) and SEM, respectively. The preliminary electrical parameters of ZnO varistors showed that the breakdown voltage V {sub b} (1 mA/cm{sup 2}) and nonlinear coefficient {alpha} is 5400 V/cm and 50, respectively, much ...

Energy Technology Data Exchange (ETDEWEB)

Multilayer mirror coatings which reflect extreme ultraviolet (EUV) radiation are a key enabling technology for EUV lithography. Mo/Si multilayers with reflectances of 67.5% at 13.4 nm are now routinely achieved and reflectances of 70 2% at 11.4 nm were obtained with MO/Be multilayers. High reflectance is achieved with careful control of substrate quality, layer thicknesses, multilayer materials, interface quality, and surface termination. Reflectance and film stress were found to be stable relative to the requirements for application to EUV lithography. The run-to-run reproducibility of the reflectance peak position was characterized to be better than 0.2%, providing the required wavelength matching among the seven multilayer-coated mirrors used in the present lithography system design. Uniformity of coating was improved to better than 0.5% across 150 mm diameter substrates. These improvements in EUV multilayer mirror ...

Energy Technology Data Exchange (ETDEWEB)

Infrared astronomical instruments require absorptive coatings on internal surfaces to trap scattered and stray photons. This is typically accomplished with any one of a number of black paints. Although inexpensive and simple to apply, paint has several disadvantages. Painted surfaces can be fragile, prone to shedding particles, and difficult to clean. Most importantly, the vacuum performance is poor. Recently a plasma enhanced chemical vapor deposition (PECVD) process was developed to apply thick (30 {micro}m) diamond-like carbon (DLC) based protective coatings to the interior of oil pipelines. These DLC coatings show much promise as an infrared black for an ultra high vacuum environment. The coatings are very robust with excellent cryogenic adhesion. Their total infrared reflectivity of < 10% at normal incidence approaches that of black paints. We measured outgas rates of <10{sup -12} ...

British Library Electronic Table of Contents (United Kingdom)

Intermetallic compound (IMC) growth at the interface between a Sn coating and a Cu substrate with or without a Ni underlayer and its related stress state was evaluated by real-time measurements using the flexure beam method. For the Sn coating without a Ni underlayer, pyramid-shaped IMC grains of Cu6Sn5 grew along the grain boundaries of Sn from the Cu substrate, especially at the triple grain boundary junctions and the IMC grains rapidly increased their volume during the initial 3?days, During this time, the IMC growth rate was 2.3??m3/day and the compressive stress in the Sn coating rapidly developed and became saturated at about ?11?MPa. In contrast, platelet IMC grains of Ni3Sn4 formed at the surface of the Ni underlayer and the IMCs grew at a rate of 1.0??m3/day for the Sn/Ni coating....

Energy Technology Data Exchange (ETDEWEB)

Kitchen oils (olive, soybean and butter) are selected for carbon coatings on LiFePO{sub 4}. The surface properties of LiFePO{sub 4} are unknown or vary depending on synthetic methods. The multi-functional groups of fatty acids in the oils can orient properly to cope with the variable surface properties of LiFePO{sub 4}, which can lead to dense carbon coatings. The low price and low toxicity of kitchen oils are other advantages of the coating process. LiFePO{sub 4} (D{sub 50} = 121 nm)combined with the carbon coating enhances the rate capability. Capacities at the 2C rate reach 150 mAh g{sup -1} or higher. The charge retention values of 2.0C/0.2C are between 94.4 and 98.9%. (author)

Science.gov (United States)

for? Learn the Issues Science & Technology Laws & Regulations About EPA Contact Us Water: Water Quality Criteria You are here: Water Science & Technology Surface Water Standards &...

International Nuclear Information System (INIS)

... hydrology norway water pollution pollution scandinavia surface waters

International Nuclear Information System (INIS)

The use of polymer matrix composites in aerospace propulsion applications is currently limited by insufficient resistance to erosion by abrasive media. Erosion resistant coatings may provide necessary protection; however, adhesion to many high temperature polymer matrix composite (PMC) materials is poor. A low pressure oxygen plasma treatment process was developed to improve adhesion of CN_x coatings to a carbon reinforced, fluorinated polymer matrix composite. Fullerene-like CN_x was selected as an erosion resistant coating for its high hardness-to-elastic modulus ratio and elastic resilience which were expected to reduce erosion from media incident at different angles (normal or glancing) relative to the surface. In situ x-ray photoelectron spectroscopy was used to evaluate the effect of the plasma treatment on surface chemistry, and electron microscopy was used to identify changes in the surface morphology of the PMC ...

International Nuclear Information System (INIS)

We have investigated the growth behaviors of high temperature compatible ZrO_2 insulation coatings on Ag and AgMg sheathed Bi_2Sr_2Ca_1Cu_2O_x superconducting tapes depending on number of dipping and thermal conditions. The coatings were fabricated on long-length superconducting tape substrates using a solution derived from Zr tetrabutoxide, solvent and chelating agent for high magnetic field magnets. The layer-on-layer growth behaviors were characterized by environmental scanning electron microscope (ESEM), energy dispersive spectroscopy (EDS), X-ray maps and X-ray diffraction (XRD). This research showed that the ZrO_2 coatings were regularly grown on Ag-based tape substrates and coating thickness increased with increasing number of dipping. It was found that ceramic oxides formed at temperature range 450 and 550 deg. C. The final coating thickness changed between 6 and 8 #mu#m ...

Energy Technology Data Exchange (ETDEWEB)

As surface treated steel sheets, steel sheets with Zn-Fe coatings as well as double-layer steel sheets with Fe-P alloy coatings on Zn-Fe alloy coatings are often used practically. Two treatment methods, which are used to dissolve only alloy layers without dissolving steel sheets in order to find amount and composition of alloy layersr have already been reported. This report investigates the mechanisms of these methods, particularly the mechanisms to control dissolution of steel sheets. In the alkali-dissolution method, Zn-Fe alloy coatings are dissolved in a strong alkaline solution(NaOH-triethanolamine (TEA)-H{sub 2}O{sub 2}). In this case, steel sheets are insoluble because passive films are formed on the surface. In the cathodic polarization electrolysis method, alloy layers are electrolyzed({minus}l.2V) and dissolved in an ammonium nitrate-0-phen electrolyte. At this potential, dissolution of steel ...

Energy Technology Data Exchange (ETDEWEB)

Steel structures immersed in seawater are protected from corrosion using cathodic protection systems (sacrificial anodes or impressed current), by paint coatings or by duplex systems in which cathodic protection hinders corrosion at coating's failure sites. The main problem related to those duplex systems is how to avoid cathodic delamination due to the alkalinity generated at cathodic sites. The present paper analyses the effectiveness of red mud suspensions as pre-treatment to avoid cathodic delamination. The study was conducted using mainly electrochemical impedance spectroscopy (EIS). The evolution of the electrode potential with immersion time was also recorded because it concerns the practical aspect of current density necessary to reach the protection potential. The study shows that red mud pre-treatments are effective in avoiding coating's delamination. (author)

Energy Technology Data Exchange (ETDEWEB)

Anti-reflective coatings made with Teflon AF2400 had the highest damage thresholds recorded for physical vapor deposited coatings at the Lawrence Livermore National Laboratory damage facility. Physical vapor deposited layers of Teflon AF2400, a perfluorinated amorphous polymer, maintained the bulk optical properties of a high transmittance from 200 nm to 1600 nm, and a low refractive index. In addition, the refractive index can be intentionally reduced by control of two common deposition parameters, deposition rate and substrate temperature. Scanning electron microscopy and nuclear magnetic resonance observations indicated that morphological changes caused the variations in the refractive index rather than compositional changes. The coatings adhered to fused silica and silicon wafers under normal laboratory handling conditions.

International Nuclear Information System (INIS)

Full text: Institute for Nuclear Research, Pitesti-Mioveni, Romania in direct cooperation with the National Institute for Laser, Plasma and Radiation Physics, Magurele, Bucharest studied and prepared for coating more than 1000 tiles made of Inconel with 7-9 #mu#m of beryllium for nuclear fusion applications at JET, Culham, UK. The principles of manufacturing processes using thermal evaporation and plasma ignited in pure metal vapors as well as by Thermionic Vacuum Arc (TVA) method and the properties of the Ni and Be coatings are presented. The prepared beryllium layers were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and atomic force microscopy. (authors)

Energy Technology Data Exchange (ETDEWEB)

Kawasaki Steel has constructed many facilities for 15 years to produce cold rolled products and galvanized products in Mizushima Works and Chiba Works. To efficiently and stably produce high and uniform quality products, various new control methods have been developed and applied to these new facilities. Especially, temperature control in a continuous annealing line, zinc coating control in a continuous galvanizing line or paint coating control in a multi-purpose coating line and tension control to achieve stable processing are the most advanced technologies and are introduced in this paper. (author)

Energy Technology Data Exchange (ETDEWEB)

Volume 2 of the water resources data for the 1992 water year for Oklahoma consists of record of stage, discharge, and water quality of streams; stage, contents, and water quality of lakes or reservoirs; and water levels of ground-water well. The report contains discharge records for 136 gaging stations; stage and contents for 31 lakes or reservoirs; water quality for 50 gaging stations. Also included are 61 partial-record or miscellaneous streamflow stations and 28 ground-water sites.

Science.gov (United States)

... Accession Number : ADD141533. Title : Yttrium Oxides in Vacuum-Plasma- Sprayed CoNiCrAlY Coatings,. Descriptive Note : Journal Article,. ...

UK PubMed Central (United Kingdom)

Synthetic oligoribonucleotides have been used to probe the interaction of MS2 coat protein with the translational operator of the MS2 replicase gene. We have investigated the possible formation of a...Full Text Available

CERN Document Server

Amperostatic coulometry was applied for the thickness measurement of Sn-Ag hot dip coatings, which comprise an extended Sn-Cu interdiffusion layer. Complementary measurements, notably weight loss, X-ray photoelectron spectroscopy, energy-dispersive X-ray spectroscopy, X-ray fluorescence (XRF), and dynamic secondary ion mass spectroscopy were performed in order to obtain a better interpretation of the coulometry results. Based on the experimental results presented in this article, the three potential changes observed during coulometry measurements are ascribed to (i) the entire dissolution of pure Sn, (ii) the formation of a CuCl salt layer, and (iii) the surface passivation. The measurement of the pure Sn mass is well reproducible despite strong coating thickness variations detected by XRF. Several experimental problems, in particular, a coating undercutting, hamper the determination of the Sn mass in the intermetallic ...

International Nuclear Information System (INIS)

This work showed the formation of phospholipid vesicle coating on inorganic sericite surface with characterization by combining electron microscopy of FE-SEM, TEM, AFM, and qualitatively evaluated the coated phospholipid vesicle by XPS as a function of etching time. The possibility of phospholipid vesicle mobility on the surface was restrained by the chelation effect of magnesium cation. The stabilization properties of phospholipid vesicles on sericite surface were demonstrated by the various concentration of magnesium cation. The presence of magnesium was found to have a much more pronounced influence on the lipid deposition process. The Mg cation plays an important role for attaching the phospholipids with optimum concentration of 7 mM. Totally, the phospholipid vesicles coating on inorganic powder could be useful for bio-related fields such as cosmetics and drug delivery system as the key functional compounds. We hope ...

UK PubMed Central (United Kingdom)

Background.The air bubbles and foam that develop during the preparation of platelet units have traditionally been considered to interact with the platelets, causing activation and...Full Text Available

UK PubMed Central (United Kingdom)

An antigen-antibody system of polystyrene tubes coated with immunoglobulin antibody was used for quantitating immunoglobulins. A similar radioimmunoassay method was adapted for a viral antigen-antibody...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This work analyzes the unoptimized prototype triode-sputtered, 150 microns thick tantalum coatings deposited with a 2.5 microns niobium underlayer on the bore of a large-diameter A723 steel cylinder. The coating was deposited for wear and erosion protection by Pacific Northwest National Laboratory. The phase determination was based on X ray diffraction analysis, wavelength dispersive X ray fluorescence analysis, energy dispersive X ray analysis, and hardness and electrical resistivity measurements. Both X ray diffraction and radius-of- curvature methods were used to determine residual stresses. A locally developed high-resolution pole figure technique was used to perform texture analysis. The post-firing, debonded coating showed alpha-tantalum, preferred 110 orientation, high surface stresses, tantalum oxides, entrapped krypton sputtering gas, interstitial oxygen, and other impurities. The surface and subsurface pole ...

Energy Technology Data Exchange (ETDEWEB)

As a result of health and safety issues surrounding the use of radioactive materials on coated optical components, there has been renewed interest in coating materials whose optical and mechanical properties approach those offered by their radioactive counterparts. Due to the radioactive nature of ThF{sub 4} and its widespread use in optical coatings, the coating industry is examining other low index and non-radioactive fluorides as possible alternatives. In this paper, the authors present the results of an experimental study on the optical and mechanical properties of thermally evaporated ThF{sub 4}, DyF{sub 3}, CeF{sub 3}, LiF, HfF{sub 4}, IRX, and IRB thin films, where the materials were deposited at different substrate temperatures. The objective is to examine this series of fluorides under comparable deposition conditions and with respect to such material properties as: n and k, film stress, and ...

UK PubMed Central (United Kingdom)

A latex agglutination (LA) test was evaluated for the detection of human rotaviruses in stool specimens. Both antiserum and immunoglobulin G (IgG)-sensitized latex particles were used, with IgG-coated...Full Text Available

International Nuclear Information System (INIS)

This paper describes the evaluation of antibody coated polystyrene beads using "1"2"5I-labelled T_3 ("1"2"5I-T_3). (author).

International Nuclear Information System (INIS)

Magnetic particles (MAG*SEP"S"M) coated with various absorbents were evaluated for the separation and recovery of low concentrations of cesium from nuclear waste solutions. The MAG*SEP"S"M particles were coated with (1) clinoptilolite, (2) transylvanian volcanic tuff, (3) resorcinol formaldehyde, and (4) crystalline silico-titanate, and then were contacted with a Hanford supernatant simulant. Particles coated with the crystalline silico-titanate were identified by Bradtec as having the highest capacity for cesium removal under the conditions tested (variation of pH, ionic strength, cesium concentration, and absorbent/solution ratio). The MAG*SEP"S"M particles coated with resorcinol formaldehyde had high distribution ratios values and could also be used to remove cesium from Hanford supernant simulant. Gamma irradiation studies were performed on the MAG*SEP"S"M particles with a gamma dose equivalent to ...

UK PubMed Central (United Kingdom)

A solid-phase radioimmunoassay employing ¹²⁵I-labeled enterotoxins and polystyrene tubes coated with specific antibody has been developed for assaying the relative concentrations of antibodies...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Effects of dopant and coating carbon nanotube on anodic performance of Si were studied for metallic anode Li ion rechargeable battery with large capacity. Although the large Li intercalation capacity higher than 1500mAhg{sup -1} is exhibited on pure Si, it decreased drastically with increasing cycle number. Increasing the electrical conductivity by doping Cr or B is effective for increasing the initial capacity and the cycle stability of Si for Li intercalation. Coating semiconductive Si with the carbon nanotube by decomposition of hydrocarbon is effective for increasing the cycle stability, though the initial Li intercalation capacity slightly decreased. Conducting binder is also important for increasing the cycle stability and it was found that Li intercalation capacity higher than 1500mAhg{sup -1} can be sustained by using poly vinyliden fruolide. Consequently, reversible Li intercalation capacity of 1500mAhg{sup -1} was successfully ...

Energy Technology Data Exchange (ETDEWEB)

Strippable or temporary coatings are innovative technologies for decontamination that effectively reduce loose contamination at low cost. These coatings have become a viable option during the deactivation and decommissioning of both US Department of Energy (DOE) and commercial nuclear facilities to remove or fix loose contamination on both vertical and horizontal surfaces. The ALARA{trademark} 1146 strippable coating was demonstrated as part of the Savannah River Site LSDDP and successfully removed transferable (surface) contamination from multiple surfaces (metal and concrete) with an average decontamination factor for alpha contamination of 6.68 and an average percentage of alpha contamination removed of 85.0%. Beta contamination removed was an average DF of 5.55 and an average percentage removed of 82.0%. This paper is an Innovative Technology Summary Report designed to provide potential users with the information they ...

Energy Technology Data Exchange (ETDEWEB)

Deposition of hard coatings may influence the mechanical properties of the bulk material and its corrosion resistance. In this work we study the hardness of the coated and the back side of 100Cr6 steel plates. Electrochemical corrosion tests were performed in O{sub 2}-saturated acetate buffer of pH 5.6 at 25degC. Chromium nitride and titanium nitride coatings prepared by different physical vapour deposition processes, such as arc, thermionic arc evaporation, magnetron sputtering and ion-beam-assisted deposition (IBAD) were compared. The results show that, for sufficient corrosion protection, chromium nitride layers have to be thicker than 500 nm. An increased nitrogen partial pressure in the evaporation chamber of the IBAD process improves the corrosion resistance significantly. The hardness of the substrates was reduced in the case of thermoionic arc evaporation only, indicating a deposition temperature of more than ...

Energy Technology Data Exchange (ETDEWEB)

Laser surface alloying with gaseous nitrogen was utilized to improve the wear resistance of a Ti-6Al-4V alloy. Wear-resistant composite coatings reinforced by hard TiN dendrites were produced 'in-situ' on a substrate of a Ti-6Al-4V alloy. The hardness and wear resistance of the laser alloyed coating under two-body abrasive and block-on-ring full-sliding wear conditions were significantly enhanced. (orig.)

International Nuclear Information System (INIS)

A series of ball-on-disc wear and friction measurements were made for surfaces which have a chemical vapour deposition carbon silicon alloy layer on a carbon substrate (fine grain POCO graphite). Nitrogen ion irradiation was used to improve the wear resistance of the carbon alloy surface. For comparison, measurements were also taken for alumina against alumina. It was found that the lowest friction coefficient and lowest wear occurred for ion irradiated coated samples containing 4% Si in the alloy and that the performance was superior to that of alumina. ((orig.)).

Energy Technology Data Exchange (ETDEWEB)

The performance of a thermophotovoltaic (TPV) converter for solar energy is compared with that of direct solar energy conversion by silicon and germanium solar cells. The optical selectivity of an intermediate emitter is computed. Experimental results on selective emission, based on selectively emitting materials and on antireflection coatings on metals, are reported. For a TPV converter equipped with silicon solar cells, no selective emitter is found to yield better results than would be obtained by direct conversion. A TPV converter with germanium cells operating with a ThO/sub 2/-coated tungsten emitter, however, may achieve a conversion efficiency superior to that of direct solar energy conversion by either silicon or germanium solar cells.

British Library Electronic Table of Contents (United Kingdom)

In this paper, an environmentally friendly metal corrosion inhibitor, phytic acid, was assembled into the walls of silica nanoparticles via layer-by-layer self-assembly technique (LbL) with poly(allylamine hydrochloride). Such functionalized nanoparticles were uniformly distributed into sol-gel films for metal anticorrosion. The films showed very pronounced and lasting protective efficiency in concentrated salt aqueous solutions as indicated by electrochemical impedance spectroscopy (EIS) measurement. These results may provide a new route for the preparation of environment-friendly anticorrosion coatings.

Energy Technology Data Exchange (ETDEWEB)

In the early 1970s Yang and Menichelli demonstrated that direct laser illumination of low-density secondary explosive prr:ssings through a transparent window could produce detonation. 'The energy requirement for threshold initiation of detonation was reduced when a thin metal coating of metal covered the side of the window against which the low-density explosive was pressed. We have obtained experimental results that are in general agreement with the results of Renllund, Stanton and Trott (1 989) and recent: work by Nagayama, hou and Nakahara (2001). We report exploration of the effects of laser beam diameter, PEiTN density and specific surface area, and thickness of a titanium coating on the window.

Energy Technology Data Exchange (ETDEWEB)

The interdiffusion behaviour of MCrAlY-coats on polycrystalline and single-crystalline materials of a similar composition (IN 738 LC/SC 16)shows similar interdiffusion characteristics. TCF-tests, where stress is generated by temperature and sample geometry at the edges of a disk-shaped sample, show that it is possible to differentiate betwee crack resistance of coated and uncoated samples. This method is also suitable for screening tests with different coat thicknesses. Coating of the edge area must, however, be done with great diligence in order to prevent coat thickness variation as results would then not be reproducable. Contrary to TCF (thermal cycle fatigue) TMF-tests (thermal mechanical fatigue)allow to set the stress states that one wishes to test. This method is therefore well suited for testing under operating conditions.(orig.) [German] Im Rahmen dieser Arbeit wurde ...

International Nuclear Information System (INIS)

After being pre-plated a zinc layer, an amorphous Al-Mn alloy coating was applied onto the surface of AZ31B magnesium alloy with a bath of molten salts. Then the corrosion performance of the coated magnesium alloy was examined in 3.5% NaCl solution by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The results showed that the single Zn layer was active in the test solution with a high corrosion rate while the Al-Mn alloy coating could effectively protect AZ31B magnesium alloy from corrosion in the solution. The high corrosion resistance of Al-Mn alloy coating was ascribed to an intact and stable passive film formed on the coating. The performances of the passive film on Al-Mn alloy were further investigated by Mott-Schottky curve and X-ray photoelectron spectroscopy (XPS) analysis. It was confirmed that the passive film exhibited n-type semiconducting ...

Science.gov (United States)

Natural bone consists of hard nanostructured hydroxyapatite (HA) in a nanostructured protein-based soft hydrogel template (ie, mostly collagen). For this reason, nanostructured HA has been an intriguing coating material on traditionally used titanium for improving orthopedic applications. In addition, helical rosette nanotubes (HRNs), newly developed materials which form through the self-assembly process of DNA base pair building blocks in body solutions, are soft nanotubes with a helical architecture that mimics natural collagen. Thus, the objective of this in vitro study was for the first time to combine the promising attributes of HRNs and nanocrystalline HA on titanium and assess osteoblast (bone-forming cell) functions. Different sizes of nanocrystalline HA were synthesized in this study through a wet chemical precipitation process following either hydrothermal treatment or sintering. Transmission electron microscopy images showed that HRNs aligned with ...

Energy Technology Data Exchange (ETDEWEB)

Water-resources data for the 1991 water year for Minnesota consist of records of stage, discharge and water quality of streams; stage, contents, and water quality of lakes and reservoirs; and water levels and water quality in wells and springs. The volume contains discharge records for 60 gaging stations; stage and contents for 9 lakes and reservoirs; water quality for 18 stream stations, 1 lake station, 22 partial-record sites, 1 precipitation station, 108 wells; and water levels for 119 observation wells. Also included are 59 high-flow partial-record stations. Additional water data were collected at various sites, not part of the systematic data collection program and are published as miscellaneous measurements or low-flow investigations.

Science.gov (United States)

swimmers in or around the water. Designate a responsible adult who can swim and knows CPR to watch swimmers in or around water. The supervisor should not be involved in any...

International Nuclear Information System (INIS)

Suspension direct current plasma spraying allows achieving finely structured coatings whose thickness is between few tens and few hundreds of micrometres. Drops (200-300 ?m in diameter) or liquid jets are mechanically injected in the plasma jet. With radial injection they are rapidly (a few ?s) fragmented into droplets (a few ?m in diameter). The latter are vaporized (in a few ?s) and the solid particles contained in suspension droplets are accelerated and melted by the plasma jet. As in conventional plasma spraying (CPS), much smaller splats (with diameters between 0.2 and 3 ?m and thicknesses between 30 and 200 nm) are arranged in layers up to form the coating. The low inertia of particles requires spray distances between 40 and 60 mm which induces plasma heat fluxes up to 22 MW m-2 participating in coating densification. Even more than in CPS, the plasma jet fluctuations, particularly for plasmas containing di-atomic ...

International Nuclear Information System (INIS)

The HT-28 and 29 irradiation capsules are part of a cooperative agreement between GA and ORNL designed to evaluate irradiation performance of unbonded BISO and TRISO coated ThO_2 fertile fuel particles. The capsules will contain a total of 44 different positions uniformly divided between each capsule. The positions in HT-29 are designated for operation at 900"0C over a fast fluence increment between 5.4 to 10.7 x 10"2"1 n/cm"2 (E > 0.18 MeV)/sub HFIR/. Positions in HT-28 are divided into two sections: 11 positions at 1250"0C to receive a fast fluence exposure between 7.8 and 8.6 x 10"2"1 n/cm"2 (E > 0.18 MeV)/sub HFIR/ and 11 positions at 900"0C designed for a 4.3 to 6.9 x 10"2"1 n/cm"2 (E > 0.18 MeV)/sub HFIR/ fast fluence exposure. Both capsuls are to serve as an evaluation test to characterize the performance of BISO OPyC coatings deposited from mixed-gas (acetylene-propylene). The OPyC variables tested will be density, ...

Energy Technology Data Exchange (ETDEWEB)

The particle surface of Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} was modified by AlF{sub 3} as a new coating material to improve the electrochemical properties in the high cutoff voltage of 4.5 V. The AlF{sub 3}-coated Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} showed no difference in the bulk structure compared with the pristine one and the uniform AlF{sub 3} coating layers whose thickness is of about 10 nm covered Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} particles, as confirmed by a transmission electron microscopy. The AlF{sub 3} coating on Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} particles improved the overall electrochemical properties such as the cyclability, rate capability and thermal stability compared with those of the pristine Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2}. Such enhancements were attributed to the presence of the stable AlF{sub 3} layer which acts as the ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

... Development Center, National Tsing-Hua University, Hsinchu, TW (China)

Energy Technology Data Exchange (ETDEWEB)

An improved process is disclosed for reducing the water content of coal containing bound water by releasing at least a portion of the bound water by maintaining the coal at a temperature from about 220/sup 0/ to about 500/sup 0/ F. in the presence of water at a pressure sufficient to maintain at least portion of the water in a liquid phase for a time sufficient to release at least a portion of the bound water wherein the improvement comprises contacting the coal during such treatment with an active material selected from the group consisting of carboxylic organic acids containing up to about 6 carbon atoms, phenol, phenolic acids and inorganic acids.

Science.gov (United States)

Jet Propulsion Laboratory. California Institute of Technology. Pasadena, California. Energy and Water Conservation. Steve Rigdon. Facilities Energy Manager ...

International Nuclear Information System (INIS)

The water and steam circuits of steam generators in pressurized-water nuclear power plants are described together with the mechanism of denting, and the corrosion of spacer plates that leads to cracks in tubes by constriction. The different chemical specifications applicable to the water of the secondary circuit of the generators in normal operation and on first commissioning are listed. The results obtained and the measurements of chemical values taken in operation on the water in the secondary circuits of steam generators at Fessenheim and Bugey are presented.

International Nuclear Information System (INIS)

We have investigated the possibility to use a microwire of BiSn to design an anisotropic thermoelectric generator. The glass-coated microwire of pure and Sn-doped bismuth was obtained by the Ulitovsky method; it was a cylindrical single-crystal with orientation (1011) along the wire axis; the C3 axis was inclined at an angle of 70 degrees to the microwire axis. It is found that doping of bismuth wires with tin increases the thermopower anisotropy in comparison with Bi by a factor of 2 - 3 in the temperature range of 200-300 K. For a Bi microwire with a core diameter of 10 ?m with a glass coating with outer diameter of 35 ?m, the transverse thermopower is ? 150 ?V/(K*cm); for BiSn, 300 ?V/(K*cm). The design of an anisotropic thermogenerator based on BiSn microwire is proposed. The miniature thermogenerator will be efficient for power supply of devices with low useful current. In addition to the considerable thermopower anisotropy of BiSn wires ...

Energy Technology Data Exchange (ETDEWEB)

A systematic study was made on MoSi{sub 2}-based nanolayer coatings. Alternating layers with thickness 1-20 nm were prepared by sputtering. Nitrided MoSi{sub 2} has a very high crystallization temperature, >1000 C, and MoSi{sub 2}Nx (x=3-4) can be used as a stable second phase reinforcement or diffusion barrier coatings. Mechanical properties depend strongly on phase and morphology of the layers: hardness and modulus is significantly increased in the crystallization. The nanolayers have much higher hardness but lower modulus (which project higher toughness in the nanolayers). Wear resistance is improved with decreasing layer thickness. Single phase MoSi{sub 2}Nx (x=0-4.2) has a wide range of hardness and modulus with varying N content and annealing, suggesting the possibility of engineering MoSi{sub 2}Nx to produce different material properties for different mechanical applications. Most of this paper is made up of viewographs.

Energy Technology Data Exchange (ETDEWEB)

High-quality solar cells have been fabricated by utilizing localized argon-ion laser decomposition of silver neodecanoate spun onto diffused silicon substrates and subsequent electroplating. Early adhesion problems during electroplating have been carefully studied and finally solved using a novel coating procedure. The laser-metallized solar cells have been characterized using lighted and dark current-voltage measurements and compared with baseline cells metallized using standard photolithographic procedures. Non-AR-coated cell efficiencies ranging from 10 to over 11% have been obtained for the laser-metallized cells, comparable with the best baseline cells. The laser-metallized cells have 30 to 40% lower series resistance than the unsintered baseline cells, indicating that in-situ sintering takes place during laser writing. A dramatic new and simpler laser metallization process on which patent protection is currently being sought has yielded ...

Energy Technology Data Exchange (ETDEWEB)

The major objective of this work is to seek for new solutions that can lead to significant lifetime improvement of submerse lines which experience severe wear processes on the polymeric layer coating used for protection of the touch down point (TDP) region. Four different materials were selected as possible candidates for the coating layer of this critical region. They are commercially available and posses well known processing technologies. The materials are two polymers: nylon 66 and polyacetal; and two composites: nylon 66 reinforced with 13 or 33% glass fiber. Stress-strain behavior was evaluated using two deformation rates in order to characterize the viscoelastic behavior proper of polymeric materials. It was observed that increasing the amount of glass fiber in the matrix leads to a stronger material and a consequent decrease of elongation to break. Additionally, abrasion tests were carried out using a Taber equipment in three distinct ...

International Nuclear Information System (INIS)

The University of Georgia, in collaboration with GE Global Research, has investigated the relevant quenching mechanism of phosphor coatings used in white light devices based on UV LEDs. The final goal of the project was the design and fabrication of a high-efficacy white light UV-LED device through improved geometry and optimized phosphor coatings. At the end of the research period, which was extended to seamlessly carry over the research to a follow-up program, we have demonstrated a two-fold improvement in the conversion efficiency of a white light LED device, where the increase efficacy is due to both improved phosphor quantum efficiency and lamp geometry. Working prototypes have been displayed at DOE sponsored meetings and during the final presentation at the DOE Headquarters in Washington, DC. During the first phase of the project, a fundamental understanding of quenching processes in UV-LEDs was obtained, and the relationships that ...

International Nuclear Information System (INIS)

A novel composite film, comprising of hydrophobic ionic liquid (IL), multi-walled carbon nanotubes (MWNTs) and gold nanoparticles (GNP), was fabricated and characterized. The GNP was introduced through electrochemical deposition on IL-MWNT gel film coated glassy carbon electrodes (GCE). Experiments showed that both IL and MWNTs could facilitate the GNP deposition. With GNP the composite film exhibited smaller electron transfer resistance and higher sensitivity in sensing guanine (G) and adenine (A). Under the optimized experimental conditions, the anodic peak currents were linear to the analyte concentration in the ranges of 0.008-2.0 ?M. The detection limits were down to nanomole level after an accumulation of 150 s on open-circuit. In addition, on the composite film coated GCE, the anodic peaks of G and A were well separated, and their response sensitivities kept almost unchanged no matter whether they coexisted or not. This proposed ...

Energy Technology Data Exchange (ETDEWEB)

A combined PVD/PECVD process for the vacuum deposition of titanium containing amorphous hydrogenated carbon films is described. Elemental compositions of the deposited films have been determined by in situ core level photoelectron spectroscopy (XPS). The long-term stability of the plasma process has been demonstrated. Target poisoning has not been observed. We have fabricated optical selective surfaces by the deposition of a-C:H/Ti multilayers onto aluminum substrates. Even though we have not optimized layer thicknesses and stoichiometries so far, the experimental results are promising: solar absorptance {alpha}{sub S} of 0.876 and thermal emittance {epsilon}{sub 100C} of 0.061 have been achieved yielding an optical selectivity sis defined as{alpha}{sub S}/{epsilon}{sub 100C} of 14.4. Accelerated aging tests of these coatings have demonstrated their aging stability: the service lifetime is predicted to amount to more than 25 years. Raman spectroscopy has been used ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the basic principles underlying the operation of low heat loss engines and the magnitude of the efficiency improvements that are theoretically achievable. The effect of varying degrees of thermal insulation on various operating parameters is examined in some detail, as is the relationship between degree of insulation and ceramic coating thickness. The effect on ceramic materials of severe surface temperature oscillations and the resultant thermal stress gradients is also discussed. In the following section, the paper describes methods of construction adopted both for ceramic inserts and coatings, and rig tests for the assessment of thermal fatigue under both load and firing cycling. The paper does not attempt to draw any general conclusions.

British Library Electronic Table of Contents (United Kingdom)

Alumina-reinforced carbon nanofiber nanocomposites were prepared using different routes; powders mixture, colloidal route and sol?gel process followed by spark plasma sintering (SPS). CNFs/xAl2O3 (x = 10?50 vol.%) were prepared through nanopowders mixing in a high-energy attrition milling. The main limitations in the preparation of this kind of nanocomposites are related to the difficulty in obtaining materials with a homogeneous distribution of both phases and the different chemical nature of CNFs and Al2O3, which causes poor interaction between them. A surface coating of CNFs by wet chemical routes with an alumina precursor is proposed as a very effective way to improve the interaction between CNFs and Al2O3. An improvement of 50% in fracture strength was found for similar nanocomposite ...

Energy Technology Data Exchange (ETDEWEB)

Carbon steel is frequently used to construct concentrated sulphuric acid storage tanks. This paper discussed the corrosion performance of carbon steel tanks and outlined the underlying mechanisms responsible for major corrosion modes. Analyses of hydrogen grooving and dilute acid corrosion failure mechanisms were presented. Recent corrosion-induced leak failures were also discussed. The use of anodic protection and organic coatings as a corrosion control measure was also evaluated. The results of laboratory studies that were conducted to understand corrosion-induced failures showed that carbon steel electrodes exhibited transpassive corrosion at relatively high anodic potentials, while stainless steel electrodes exhibited transpassive corrosion at anodic potentials less than 1 V. It was concluded that corrosion-induced leaks can be prevented by using anodic protection and baked phenolic coating technologies. 23 refs., 9 figs.

International Nuclear Information System (INIS)

One of the significant factors of neutron radiographic image degradation is scattering blur from the object. A practical method is described to enhance image quality by eliminating the overlapping of scattered thermal neutrons component from the objects in ETRR-2 neutron radiography facility, using aluminum Gd-coated antiscatter grid. The MCNP code was used to determine the optimum grid dimensions that will reduce the scattered thermal neutrons from the object. An experiment was performed to determine the optimum grid height and irradiation time that gives the best image with acceptable geometric unsharpness. Using the MCNP code it was found that 97% of the scattered neutrons were removed by the grid. The wall dimensions and Gd coating are so small that the facility resolution cannot detect the image pattern superposition on the film.

Energy Technology Data Exchange (ETDEWEB)

This paper described a risk control management tool that has been developed by Petrobras Petroleo, the largest Brazilian oil company and one of the world's leading oil companies. The system covers health, safety and environmental (HSE) issues regarding pipeline construction projects. The limitations of traditional safety management systems for coping with the critical problems related to environmental safety issues were discussed. In particular, this paper described how the HSE tool evaluates the risks resulting from the following aspects of onshore pipeline construction and assembly: establishing right-of-way and route locations, transporting pipe, developing the construction site, opening the trench, pipe laying, pipe bending, concrete external coating, welding, external anticorrosive coatings, pipe placement backfilling, hydrostatic testing, maintenance operations, and pipeline commissioning. 6 refs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

Methods for improving the sensitivity of scintillation cells for radon concentration measurements were studied with emphasis on improving light collection efficiency. This allows the length and hence the volume of the cell to be increased. Variables studied were choice of scintillator material, its method of application and thickness, length of cell, cell material, type and configuration of reflectors, choice of photomultipliers, and factors affecting background. Response from various areas of the cell surface was studied with an alpha source and with radon filling. Coating the window with phosphor was found to be counter-productive. The optimum results obtained were with the inside of the cell (other than the window) covered with a thick layer of ZnS(Ag), or with a thick layer of reflective material coated with a thin layer of phosphor. With it, a 10 cm diameter plexiglass cell can be extended to at least 50 cm length without difficulty from ...

International Nuclear Information System (INIS)

DZ4 substrates were coated with NiCoCrAlY by plasma spray and subsequently treated by high current pulsed electron beams(HCPEB) of different parameters. The surface microstructure, phase structure and high temperature oxidation resistance were studied. It has been shown that as a result of the HCPEB treatment the loose and rough structure remelted and the surface became smooth. Smooth microregion, craters and cracks appeared on the surface. The ?' phase manifolded and there was no visible thermal stress. The oxidation test at 900 degree C for 100 h showed that a more compact and successive ?-Al_2O_3 scale was formed on the surface of the samples after HCPEB irradiation, which improved the oxidation resistance of the NiCoCrAlY coatings obviously. (authors)

British Library Electronic Table of Contents (United Kingdom)

b-carotene, a natural antioxidant, beneficial form human health prospective. In this study we had examined the recovery of b-carotene form mesoporous carbon coated monolith (MCCM) by batch process. Desorption kinetics and isotherm studies were carried out by using n-hexane as an eluent. Isotherm studies showed better applicability of Langmuir model. The first-order two-compartment three-parameter kinetics model as a function of initial loading concentration and reaction temperature was applied. It was observed that b-carotene desorption process is controlled by both rapid and slow desorption. Results showed that the slow desorption fraction increases from 0.8446 to 0.9007 with increase in initial loading concentration from 10.83 to 39.72mg/g while, the slow desorption fraction decreases fr...

British Library Electronic Table of Contents (United Kingdom)

Abstract A novel and convenient protocol for the preparation of an open-tubular column coated with chitosan-silica hybrid using chitosan and silane-coupling agent (-glycidoxy-propyltrimethoxysilane) was developed for CEC, in which, chitosan was covalently bonded to the inner wall of a fused-silica capillary using -glycidoxy-propyltrimethoxysilane as a cross-linking agent. The stationary phase was hydrophilic due to the chitosan-silica hybrid with abundant amine and hydroxyl functional groups. The chromatographic characteristics of the column were evaluated by the separation of some organic acids and inorganic anions. The column showed good selectivity for nucleotides, aromatic acids, and inorganic anions. The mechanism for the separation of these compounds was primarily based on the hydrop...

British Library Electronic Table of Contents (United Kingdom)

Superalloys, such as Inconels and Incoloys, are extensively used where high strength is a requirement. However, where these materials are required to slide against one another, particularly with poor or no lubrication, high friction levels and seizure are commonly seen to occur, which can cause component failure. In this work seizure characteristics of three superalloys (Inconel 718 and Incoloys 945 and 945X) were investigated, uncoated, coated with Armoloy (a hard, thin, dense chrome coating with a micro-nodular surface texture) and plasma nitrided in dry sliding conditions. A rig purpose built for initiating seizure was used. It involves sliding a ball against a disc at constant speed while the load is increased. Tests are designed to last less than one rotation so that the wear scar can...

Energy Technology Data Exchange (ETDEWEB)

Corrosion is said to be the most dominant factor which affects the physical life of ships and offshore structures. In order to secure the structural safety of ships and offshore structures, it is necessary to take measures to corrosion based on the prediction of condition of progressive corrosion. But such prediction is difficult because the behavior of corrosion`s progress is probabilistic. In this paper, probabilistic model, which could evaluate the degradation of coatings and the successive corrosion of steel members, was proposed in order to explain the tendency of the actual corrosion conditions of existing ships. Then, statistical inferences on the proposed model were made by applying the actual data on plate thickness measurements of Bulk Carriers` Cargo Hold. And validity of the proposed model was verified.

International Nuclear Information System (INIS)

Cooling water is sprayed on the outer surface of an upper portion of a container, and a pool is formed by the cooling water flowing down while cooling the container. Further, the cooling water stored in the cooling water pool is recycled by a pump for spraying the cooling water on the outer surface of the upper portion of the container. Sufficient amount of cooling water is supplied for spraying the cooling water to the outer surface of the upper portion of the container so that the outer surface of the container is free from drying and a liquid membrane is formed on the entire surface. The amount of the cooling water is made greater than that of the cooling water evaporated when the entire amount of the heat generate in the reactor core of the reactor is transferred to the cooling ...

Energy Technology Data Exchange (ETDEWEB)

The chemistries of reactants, plasticizers, solvents and additives in an epoxy paint are discussed. Polyamide additives may play an important role in the absorption of molecular iodine by epoxy paints. It is recommended that the unsaturation of the polyamide additive in the epoxy cure be determined. Experimental studies of water absorption by epoxy resins are discussed. These studies show that absorption can disrupt hydrogen bonds among segments of the polymers and cause swelling of the polymer. The water absorption increases the diffusion coefficient of water within the polymer. Permanent damage to the polymer can result if water causes hydrolysis of ether linkages. Water desorption studies are recommended to ascertain how water absorption affects epoxy paint.

Energy Technology Data Exchange (ETDEWEB)

This thesis deals with the analysis of dominant loss mechanisms in direct methanol fuel cells (DMFC) and hydrogen fed polymer electrolyte membrane fuel cells (PEFC) by means of experimental characterization and modeling work. Due to different fuels used in these two fuel cell types, the dominant loss mechanisms are different in their nature. All in-situ characterization techniques that are used in this work are based on a novel test fuel cell with embedded reference electrodes. The first part of this work presents a new concept for realizing a reference electrode configuration in a polymer electrolyte membrane fuel cell by means of laser ablation. The laser beam is used to evaporate a small gap into the electrode surface of a catalyst coated membrane (CCM) to isolate the reference electrode from the working/counter electrode (WE/CE). This method enables the simultaneous ablation of the electrodes on both sides of the CCM because the membrane is transparent for the ...

Energy Technology Data Exchange (ETDEWEB)

This procedure describes the formulation and make-up of Simulated Dilute Water (SOW), a low-ionic-content water to be used for Activity E-20-50, Long-Term Corrosion Studies. This water has an ionic content which is nominally a factor of ten higher than that of representative waters at or near Yucca Mountain. Representative waters were chosen as J-13 well water [Harrar, 1990] and perched water at Yucca Mountain [Glassley, 1996]. J-13 well water is obtained from ground water that is in contact with the Topopah Spring tuff, which is the repository horizon rock. The perched water is located in the Topopah Spring tuff, but below the repository horizon and above the water table. A nominal times ten higher ionic content was chosen to simulate the effect of ionic ...

International Nuclear Information System (INIS)

The research committee of the Atomic Energy Society of Japan on water chemistry standard aims at establishing the private standard of water chemistry of nuclear power plants. The committee gathers up 'BWR water chemistry management manual', 'PWR primary system water chemistry management manual' and 'PWR water chemical analysis standard method', and furthermore aims at the standardization of those in future. Looking back on the committee's activities for the past four years, latest results of research of water chemistry mainly contributing to safe and reliable nuclear power plants were described with the future perspective of water chemistry and a demanded break-through. (T.T.)

International Nuclear Information System (INIS)

In equipment industries, the equipments handling industrial water and pure water are numerous. In power generation including nuclear power generation, water serves as a working medium. Review is made on the experiences in the corrosion of iron and nickel base alloys in high temperature, high pressure water and the results of researches derived from them. Under high temperature and high pressure, carbon steel, low alloy steel, stainless steel and high nickel alloy cause corrosion even in pure water. But in the case of serious corrosion, chlorine, oxygen, alkali and others in water take part. The following matters are described: corrosion by steam; stress corrosion cracking in pure water; corrosion by impurities in high temperature, high pressure pure water, i.e. chlorine ions, dissolved oxygen, and alkali; corrosion under ...