International Nuclear Information System (INIS)

The ion mobilities of |"2"1"1At|At(I) in dependence on thiourea (tu) concentration, iodide concentration and a mixture of both ligands were measured by the electromigration method in free electrolytes. An equilibrium model was developed for the characterization of electromigration curves which permitted the calculation of stability constants and ion mobilities of the complexes |AtI|, |AtI_2|"-, |Attu|"+, |Attu_2|"+ and |AtItu| existing in these solutions. Ethanol and water served as solvents. The temperature was 298 K and the ionic strength was about 0.05 mol/dm"3. (author) 16 refs.; 2 figs.

International Nuclear Information System (INIS)

The diffusion coefficients (De) in bentonite were measured to understand and quantify the influence of groundwater chemistry such as ionic strength and to quantify the alteration of smectite mineralogical transformations. (author)

Energy Technology Data Exchange (ETDEWEB)

This procedure describes the formulation and make-up of Simulated Dilute Water (SOW), a low-ionic-content water to be used for Activity E-20-50, Long-Term Corrosion Studies. This water has an ionic content which is nominally a factor of ten higher than that of representative waters at or near Yucca Mountain. Representative waters were chosen as J-13 well water [Harrar, 1990] and perched water at Yucca Mountain [Glassley, 1996]. J-13 well water is obtained from ground water that is in contact with the Topopah Spring tuff, which is the repository horizon rock. The perched water is located in the Topopah Spring tuff, but below the repository horizon and above the water table. A nominal times ten higher ...

International Nuclear Information System (INIS)

This paper describes stable strontium as composed of four stable isotopes ( Sr 88, Sr 87, Sr 86, and Sr 84), of which Sr 88 contributes more than 82% to its composition. Strontium exists in three crystalline, plymorphic forms; face-centered cubic alpha form, hexagonal beta form and body-centered cubic gamma form. Strontium occupies in many physicochemical aspects an intermediate position between calcium and barium, as does the solubility of strontium salts. As a result of its oxidation potential, strontium readily forms oxides, halides, and sulfide. The author proposes that the slight discrimination against strontium incorporation into bony tissues may be due to the difference in ionic potential (14%) between strontium and calcium. Ionic potential is an indicator of the strength of ionic bonds: strontium has a smaller ratio of ionic charge to ionic radius when ...

British Library Electronic Table of Contents (United Kingdom)

The key factors of enzymatic lysis of cells are the interaction between the enzyme and the cell - catalytic and non-catalytic adsorption of enzyme on cell surface. Here, the studies of lysis of intact Escherichia coli cells by chicken egg white lysozyme were performed. It was found that the ionic strength has a dual effect onto the system. On the one hand, the desorption constant of the enzyme increases with the increase of the solution ionic strength, which results in a better enzyme performance. On the other hand, due to the higher osmosis, the cell lysis rate decreases with the increasing of ionic strength of the system. It was found that pH 8.6 and 30mM NaCl are optimal conditions for lysis of E. coli cells by lysozyme.

British Library Electronic Table of Contents (United Kingdom)

A Brownian dynamics simulation has been used to investigate the aggregation kinetics of bimodal colloidal mixtures with similar surface chemistries but different sizes, driven by the DLVO interaction potential. The time evolution of structural formation is examined by the mean number of neighbors under fast and slow aggregation regions. It was found that the electrolyte ionic strength affects the kinetic pattern of colloidal aggregation. Under the high electrolyte ionic strength conditions (fast aggregation), the selective aggregation of the least stable single component can take place in the early stage, while the other component is enriched in this least stable component in the later stage. With the ionic strength decreasing (towards the slow aggregation), the hybrid aggregation (selecti...

Science.gov (United States)

The effects of various fixative agents, pH, ionic strength, stain concentration, and magnesium concentration on DNA staining with the antibiotics olivomycin, chromomycin A3, and mithramycin were examined with DNA in solution and in mammalian cells.

British Library Electronic Table of Contents (United Kingdom)

In this study two surface sensitive methods, i.e. quartz crystal microbalance with dissipation monitoring (QCM-D) and ellipsometry, were used for erosion measurements of a rosin-based marine antifouling paint binder. Thin films of the binder were applied on sensor surfaces by the means of spin-coating and the effect of water velocity over the paint film, water temperature or ionic strength on erosion was investigated. Both the acoustic QCM-D model and the optical ellipsometry model gave comparable erosion results. The initial 2-50nm rapid erosion of the top layer was followed by steady-state erosion rate until end of experiment. For example, the steady-state erosion rate was 12nm/24h in artificial seawater at 23degreeC and with a flow of 200ml/min over the paint surface as measured with QC...

Energy Technology Data Exchange (ETDEWEB)

{sup 60}Co is produced as an activation product and is present in the low-level aqueous radioactive waste released from the La Hague plant. At present, the concentration in the sea (non filtered at 0.45 {mu}m) at the Goury site are close to or even below, the detection limit: 0.2 mBq.l{sup -1}. The {sup 60}Co speciation depends on the type of effluent considered: in the effluent A ('active'), the cobalt is in the form of a stable trivalent complex; in the effluent V (to be checked), the cobalt is in majority (50% of the activity release) in the form of particles (>0.45 {mu}m), and then in the form of two soluble species: ionic divalent (Co{sup 2+}) and some stable complexes. The evolution of the reprocessing techniques used does not affect the speciation. So, since the nuclear reprocessing plant started at the La Hague plant in 1966, the chemical species discharged in the sea shows time variation related to the evolution of the type of ...

Energy Technology Data Exchange (ETDEWEB)

This study reports on the physical-chemical behaviour of swelling di-octahedral clays (smectites) and their interaction with aqueous solutions and bacteria (Shewanella putrefaciens). Experimental results are presented for compacted clays, hydrated under confined volume conditions, using a new type of reaction-cell (the 'wet-cell' of Warr and Hoffman, 2004) that was designed for in situ X-ray diffraction (XRD) measurement. For comparison, dispersed clay systems were studied using standard batch solutions subjected to varying degrees of agitation. The combination of time-dependent in situ XRD measurements with gravimetric measurements and calculated diffraction patterns using the CALCMIX software (Plancon and Drits, 1999) allowed to successful quantification of the dynamics of water uptake and storage. This analytical procedure combined with published water vapour adsorption data enabled determination of the abundance of ...

Science.gov (United States)

... Page 26 Ultimate compressive strength versus fly ash/cement limits 41 ... 222 El Ultimate compressive strength versus water/(cement + fly ash) 250 ...

UK PubMed Central (United Kingdom)

The movement of cells and cell fragments in an electric field provided a means for determining the nature of cellular surface charges. We found that changes in ionic strength and particularly changes...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The kinetics of the reaction of carbon dioxide in MDEA solutions were studied both experimentally and theoretically. It is concluded that MDEA acts as a homogeneous catalyst for CO/sub 2/ hydrolysis, and as a result the rate of absorption in aqueous MDEA solutions is significantly larger than one would calculate by simply taking into account the alkalinity of the reaction. A possible zwitterion mechanism is proposed for this reaction. The minor effect of ionic strength were also studied with the presence of other ions. 19 references, 6 figures.

British Library Electronic Table of Contents (United Kingdom)

The behavior of proton transfer facilitated by a novel thiazole derivative, N-methyl-4-(4-phenoxyphenyl)thiazol-2-amine (MPPT), across the water/1,2-dichloroethane (1,2-DCE) interface was investigated electrochemically. The ionic partition diagram for MPPT was obtained from interpretation of the cyclic voltammograms. The apparent partition coefficient of MPPT was evaluated by the shaking-flask method under experimental conditions, while that for the protonated form of MPPT was calculated from its transfer potential obtained from the ionic partition diagram. It was suggested that the mechanism for transfer of MPPT across the water/1,2-DCE) interface depends on the pH of the aqueous phase. The parameters of the facilitated proton transfer across the water/1,2-DCE interface were evaluated as ...

Energy Technology Data Exchange (ETDEWEB)

The Dowex 50W-X8 and 50W-Xl2 resin samples are both strong acid cation materials in the hydrogen form. Each material has a water retention capacity characteristic of its respective marketed degree of cross-linking. Dowex 21K gives confirmatory responses to tests for a strong anion exchange resin in the nitrate form. All three resins have the manufacturer's specified ionic type and form, and the Dowex 50W resins have characteristic water retention capacities. These tests conclude that the ion exchange resins in use in FB-Line meet the approved safety document criteria for cross-linking, ionic form, and resin type.

Energy Technology Data Exchange (ETDEWEB)

A type of mesoporous ZrO{sub 2} was synthesized and its phosphate removal potential was investigated in this study. The adsorption isotherm, pH effect, ionic strength effect and desorption were examined in batch experiments. The adsorption data fitted well to the Langmuir model with which the maximum P adsorption capacity was estimated to be 29.71 mg P/g. The amount of phosphate adsorbed increased rapidly in the first 5 h and slowly towards the end of the run, suggesting the possible monolayer coverage of phosphate ions on the surface of the adsorbent. The phosphate adsorption tended to increase with a decrease of pH and an increase of ionic strength. A phosphate desorbability of approximately 60% was observed with 0.5 M NaOH, which indicated a relatively strong bonding between the adsorbed PO{sub 4}{sup 3-} and the sorptive sites on the surface of the adsorbent. The immobilization of phosphate probably ...

Environmental Research Database

ObjectivesObjectives Not AvailableDescriptionTo determine the effects of water penetration on the burst strength of filament wound composite pipes which have been damaged by impact and then subjected to long term pressurisation with sea water. ~%~ To monitor and characterise the damage and effects of sea water penetration using ultrasonic NDT. To determine the burst strength of bonded composite pipe joints with and without defects and to see whether the defects can be detected using ultrasonic NDT. [continued...

British Library Electronic Table of Contents (United Kingdom)

This study compares two series of solvents for application in aluminum electrolytic capacitors: ethylene glycol (EG) and water mixtures, and ethylene glycol and 1-n-butyl-3-methylimidazolium tetrafluoroborate (BMI.BF4) ionic liquid (IL) mixtures. Electrochemical impedance spectroscopy and cyclic voltammetry were carried out with a previously anodized aluminum disk electrode. Comparative measurements of solution resistance, polarization resistance, AC capacitance, and passive current were made. The results show that EG?IL mixtures with low amounts of IL (10% IL?90% EG v/v) have a low solution resistance. Low values of solution resistance, high values of polarization resistance, small passive current, and uniform capacitance of anodized aluminum in EG?IL mixtures are favorable properties of ...

International Nuclear Information System (INIS)

Consideration is given to the data, demonstrating the effect of ion radiation on strength characteristics of ionic crystals, presented by magnesium oxide. Crystals, prepared in the form of plates, were irradiated by Si"+, Fe"+, C"+ ions by the dose of 10"1"6-10"1"7 ion/cm"2 at room temperature in vacuum. The following characteristics were investigated: dislocation density, microhardness, crack resistance. Investigation of dislocation structure showed, that dislocation density in irradiated sample was 2-3 times higher, as compared to nonirradiated one. Sufficient increase of fracture viscosity of MgO crystals was revealed. It can be conditioned by occurrence of compression stresses in the surface layer, decelerating crack formation and propagation.

Energy Technology Data Exchange (ETDEWEB)

The objective of this work is to improve the process for CO{sub 2} capture by alkanolamine absorption/stripping by developing an alternative solvent, aqueous K{sub 2}CO{sub 3} promoted by piperazine. CO{sub 2} mass transfer rates are second order in piperazine concentration and increase with ionic strength. Modeling of stripper performance suggests that 5 m K{sup +}/2.5 m PZ will require 25 to 46% less heat than 7 m MEA. The first pilot plant campaign was completed on June 24. The CO{sub 2} penetration through the absorber with 20 feet of Flexipac{trademark} 1Y varied from 0.6 to 16% as the inlet CO{sub 2} varied from 3 to 12% CO{sub 2} and the gas rate varied from 0.5 to 3 kg/m{sup 2}-s.

Science.gov (United States)

The effects of freeze-thaw cycling on the strength and durability of samples of compacted, stabilized, wet flue gas desulfurization (FGD) by-products are reported. The results of laboratory tests show a clear relationship between higher water contents and...

Science.gov (United States)

Our long-term goal is to enable highly productive plant species to extract, resist, detoxify, and/or sequester toxic heavy metal pollutants as an environmentally friendly alternative to physical remediation methods. We have focused this phytoremediation research on soil and water-borne ionic and methylmercury. Mercury pollution is a serious world-wide problem affecting the health of human and wild-life populations. Methylmercury, produced by native bacteria at mercury-contaminated wetland sites, is a particularly serious problem due to its extreme toxicity and efficient biomagnification in the food chain. We engineered several plant species (e.g., Arabidopsis, tobacco, canola, yellow poplar, rice) to express the bacterial genes, merB and/or merA, under the control of plant regulatory sequences. These transgenic plants acquired remarkable properties for mercury remediation. (1) Transgenic plants expressing merB (organomercury lyase) extract ...

British Library Electronic Table of Contents (United Kingdom)

Miscanthus is a potential feedstock for the production of biofuels. Lignocellulosic biomass is not soluble in conventional solvents, but Miscanthus and other lignocellulosic biomass have reasonable solubilities in some ionic liquids. The solubility of Miscanthus in a variety of hydrophilic ionic liquids was measured as a function of particle size, temperature and time for dissolution. In addition to temperature and time, the ionic liquid anion has a significant effect on solubility and rate of dissolution. The moisture content of Miscanthus lowers its solubility in certain ionic liquids. Chloride, acetate, and phosphate-based ionic liquids favor solubility. A tentative correlation for the solubility of Miscanthus is proposed in terms of Abraham solvation parameters obtained from quantum-ch...

Energy Technology Data Exchange (ETDEWEB)

The improvement of the ecological conditions at waste storing reservoirs is an important task of the restoration activity at Production Association (PA) ``Mayak`` (South Urals). The radionuclides mostly {sup 90}Sr, {sup 137}Cs, and chemical pollutants deposited in the reservoir water and in the bottom sediment are very dangerous sources for the contamination of Techa River below the reservoirs and the contamination of groundwater in the surrounding formations. The spreading of radioactive contaminants has both hydrogeological and the chemical features. The thermodynamic approach used to account for physical-chemical interactions between water and the bed rocks based on Gibbs free energy minimization of multicomponent system (H-O-Ca-Mg-K-Na-S-Cl-C-Sr) permitted the authors to calculate the corresponding ionic and complex species existing in the solutions, and to characterize the processes of precipitation and dissolution. ...

Energy Technology Data Exchange (ETDEWEB)

Notched and smooth cylindrical plasma nitrided (PN) and quench and tempered (Q and T) steel specimens made of a B-Mn SS2131 ({approx}AISI 15B21H) steel have been exposed to constant amplitude plane reversed bending corrosion fatigue tests (R = -1) at 47 Hz in sea water. S - N curves show that sea water suppresses the fatigue limit and reduces fatigue strength (especially at long lives) of smooth and notched Q and T and PN specimens. Plasma nitriding improves the corrosion fatigue resistance of Q and T specimens; this is associated with the good corrosion resistance of {epsilon} and {gamma}`-phases, the enhancement of corrosion and fatigue by compressive residual stresses, and the consumption of H{sup +} ions during reduction of nitrogen. This improvement is more significant for smooth specimens and for long lives. Notch sensitivity of Q and T and PN specimens decreases with fatigue life. Pitting corrosion, cyclic applied ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Ions of rare earth elements (r.e.e.) have been found to form with benzilic acid and rhodamine B precipitates hardly soluble in water and extractable by toluene. The conditions of La and Pr determination by extraction-spectrophotometry method are studied. Relative square deviation does not exceed 0.027 and 0.034 respectively. The method can be used for determination of other cerium sub-group r.e.e. in their salts and cannot be employed for determination of lighter r.e.e. in the presence of heavier r.e.e., because the latter form low soluble precipitates capturing the r.e.e. situated in the beginninq of the r.e.e. series.

International Nuclear Information System (INIS)

Purpose: To compare the diagnostic quality and adverse events of the water-soluble, non-ionic, iso-osmolar, dimeric contrast media iodixanol and iotrolan in hysterosalpingography (HSG). Material and Methods: One hundred and twenty patients participated in a double-blind randomized parallel-group phase-III study. Questionnaires and patient interviews were used. Diagnostic quality was assessed using a visual analogue scale and the quality in specific regions was rated using a categorical scale. Results: Overall diagnostic quality was equal for the two groups. There was no statistically significant difference between the two groups in diagnostic quality in the specific regions of interest. No differences between the contrast media were found with regard to adverse events. Conclusion: Both contrast media provided images of high diagnostic quality in HSG. (orig.)

British Library Electronic Table of Contents (United Kingdom)

ObjectivesThe aim of this study was to evaluate the relationship between micro-tensile bond strength (mTBS) and ultimate tensile strength (UTS) of resin composite restorations in cavities filled by a bulk or incremental technique using the micro-tensile test.MethodsClass I cavities (4mm long, 3mm wide, 3mm deep) were prepared into dentine of sixteen human molars. All cavities were bonded with Clearfil SE Bond and restored with AP-X composite with either a bulk or incremental technique. After storage in water for 24h, the teeth were vertically sectioned to yield two slabs. Each slab was sectioned into three sticks. Sticks of one slab were trimmed into an hourglass of 0.7mm2 area at resin-dentine interface for bond strength measurement while the other sticks were trimmed at the centre of the...

International Nuclear Information System (INIS)

The distribution of Cu, Ni, Co and Mn between an aqueous solution of constant ionic strength and Versatic Acid 911 diluted with benzene was investigated. Only one extracted species of Cu was revealed to have a dimeric structure of the composition (CuR_2.RH)_2, while both monomer and dimer were found in the extraction of Ni, Co and Mn. The curve-fitting method was employed to determine these species, from which the composition of the extracted species was found to be NiR_2.4RH and (NiR_2.2RH)_2, CoR_2.4RH and (CoR_2.2RH)_2, and MnR_2.4RH and (MnR_2.2RH)_2, respectively. The apparent equilibrium constants of the above species and those between monomer and dimer were also determined. The curve-fitting method was proved to be a precise method for determining the equilibrium constants and extracted species. (author).

International Nuclear Information System (INIS)

The kinetics of oxidation of uranium (IV) monofluoride complex by nitrous acid in nitric acid solution have been studied. The experiments were carried out at constant ionic strength of 2M (HNO_3 and NaNO_3) and temperature in the range of 18-47 deg C. The rate of reaction was determined spectrophotometrically at a wavelength of 621 nm, at which the molar extinction coefficients of UF"3"+ and UF_2"2"+ are the same. It was shown that reaction orders for [HNO_2] and [HNO_3] are equal to 0.12 and 0.39, respectively. The values of activation parameters #DELTA#H"#not =# and #DELTA#S"#not =# are determined to be 83 kJ mol"-"1 and 75 J (mol.K)"-"1, respectively. The rate order of the reaction studied has a weak direct depedence on [H"+] in contrary to the strong and reverse dependence in the absence of fluoride ions. In conclusion, fluoride ions may strongly stabilize the U(IV) in nitric acid solutions. (author) 4 refs.; 3 figs.; 2 tabs.

International Nuclear Information System (INIS)

Magnetic particles (MAG*SEP"S"M) coated with various absorbents were evaluated for the separation and recovery of low concentrations of cesium from nuclear waste solutions. The MAG*SEP"S"M particles were coated with (1) clinoptilolite, (2) transylvanian volcanic tuff, (3) resorcinol formaldehyde, and (4) crystalline silico-titanate, and then were contacted with a Hanford supernatant simulant. Particles coated with the crystalline silico-titanate were identified by Bradtec as having the highest capacity for cesium removal under the conditions tested (variation of pH, ionic strength, cesium concentration, and absorbent/solution ratio). The MAG*SEP"S"M particles coated with resorcinol formaldehyde had high distribution ratios values and could also be used to remove cesium from Hanford supernant simulant. Gamma irradiation studies were performed on the MAG*SEP"S"M particles with a gamma dose equivalent to 100 cycles of use. This irradiation ...

International Nuclear Information System (INIS)

Chelating tendencies of several biologically important compounds viz. glycocyamine (GCN: N-amidino-aminoethanoic acid) taurine (TRN: 2-aminoethanesulphonic acid) and pyridoxal [PDL: 3-hydroxy-5-(hydroxymethyl)-2-methyl-pyridine-4-carbaldehyde] have been examined by pH-metric titration technique in their binary complex formation with copper(II) and uranyl(VI) ions. The work has further been extended to investigating the ternary complex formation involving 2.2'-bipyridine. 1,10-phenanthroline or nitrilotriacetic acid as a primary and TRN and PDL as secondary ligands. All the experiments were carried out at 25"0C and at an ionic strength of 0.1M (NaCl0_4) in aqueous or 50% (v/v) aqueous-ethanol medium according to the suitability of the experimental conditions. Stabilities of ternary complexes as compared to those of the corresponding binary complexes of the secondary ligands have also been discussed. (author).

Energy Technology Data Exchange (ETDEWEB)

This paper reports area and time dependent dielectric breakdown distributions of ethylene glycol and water solutions cooled to -23/sup 0/C. Electrode areas of 80, 400, 2000, and 10,000 cm/sup 2/ spaced 1 cm apart were repeatedly stressed with voltage pulses exponentially decaying in 5 to 20 ms. Approximately 80,000 measurements concentrated at electric field strengths near the 1% breakdown probability region of the samples were taken in order to obtain statistically accurate data on the dielectric strength of this liquid.

International Nuclear Information System (INIS)

A series of cation exchange membranes was produced by impregnating and coating both sides of a quartz web with a Nafion solution (1100 EW, 10%wt in water). Inert filler particles (SiO_2, ZrO_2 or TiO_2; 5-20%wt) were incorporated into the aqueous Nafion solution to produce robust, composite membranes. Ion-exchange capacity/equivalent weight, water take-up, thickness change on hydration and ionic and electrical conductivity were measured in 1 mol dm"-"3 sulfuric acid at 298 K. The TiO_2 filler significantly impacted on these properties, producing higher water take-up and increased conductivity. Such membranes may be beneficial for proton exchange membrane (PEM) fuel cell operation at low humidification. The PEM fuel cell performance of the composite membranes containing SiO_2 fillers was examined in a Ballard Mark 5E unit cell. While the use of composite membranes offers a cost reduction, the unit cell ...

International Nuclear Information System (INIS)

A new series of lithium ionic liquids were prepared by introducing of two electron-withdrawing trifluoroacetyl groups in borate salts containing two methoxy-oligo(ethylene oxide) groups in the structures. Successive substitution reactions of oligo-ethylene glycol monomethyl ether and trifluroacetic acid from LiBH_4 yielded the lithium salts, which were clear and colorless liquids at room temperature. The fundamental physicochemical properties, such as density, thermal property, viscosity, ionic conductivity, self-diffusion coefficients, and electrochemical stability, were measured. The lithium ionic liquids had self-dissociation ability and conducted ions even in the absence of organic solvents. New polymer electrolytes, named 'ion gels', were prepared by radical cross-linking reactions of a poly(ethylene oxide-co-propylene oxide)tri-acrylate macromonomer in the presence the lithium ionic liquid. An ...

Energy Technology Data Exchange (ETDEWEB)

We report synthesis, characterization and ion transport in polyether-based ionic melt electrolytes consisting of Li salts of low-basicity anions covalently attached to polyether oligomers. Purity of the materials was investigated by HPLC analysis and electrospray ionization mass spectrometry. The highest ionic conductivity of 7.1 x 10{sup -6} S/cm at 30 deg. C was obtained for the sample consisting of a lithium salt of an arylfluorosulfonimide anion attached to a polyether oligomer with an ethyleneoxide (EO) to lithium ratio of 12. The conductivity order of various ionic melts having different polyether chain lengths suggests that at higher EO:Li ratios the conductivity of the electrolytes at room temperature is determined in part by the amount of crystallization of the polyether portion of the ionic melt.

CERN Document Server

We review a new theoretical approach to the kinetics of surfactant adsorption at fluid-fluid interfaces. It yields a more complete description of the kinetics both in the aqueous solution and at the interface, deriving all equations from a free-energy functional. It also provides a general method to calculate dynamic surface tensions. For non-ionic surfactants the results coincide with previous models. Common non-ionic surfactants are shown to undergo diffusion-limited adsorption, in agreement with experiments. Strong electrostatic interactions in salt-free ionic surfactant solutions are found to lead to kinetically limited adsorption. In this case the theory accounts for unusual experimental results which could not be understood using previous approaches. Added salt screens the electrostatic interactions and makes the ionic surfactant adsorption similar to the non-ionic case. The ...

International Nuclear Information System (INIS)

Allyl alcohol (AA), acrylonitrile (AN), methyl methacrylate (MMA), monomers and monomer mixtures AA+AN, AA+MMA were used to conserve and consolidate Beech and Spruce. After impregnation, copolymerisation and polymerisation were accomplished by gamma irradiation. The fine structure of wood+polymer(copolymer) composites was investigated by Scanning Electron Microscopy (SEM). It was observed that copolymer obtained from AA+MMA monomer mixture showed the optimum compatibility. The compressional strength and Brinell Hardness Numbers determined for untreated and treated wood samples indicated that the mechanical strength of wood+copolymer composites was increased. It was found that the mechanical strength of the wood samples containing the AA+MMA copolymer was higher than the others. In the presence of P(AA/MMA), at highest conversion, the compressive strength perpendicular to the fibres in Beech and Spruce ...

International Nuclear Information System (INIS)

Dependence of C, N and Nb contents on intergranular corrosion (IGC), strews corrosion cracking (SCC) and mechanical strength of alloy 600 were examined. To evaluate the corrosion resistance of heat affected zone (HAZ), post weld heat treated specimens were used. To evaluate I G C and S C C susceptibility, Ferric Sulfate-Sulfuric Acid Test and High Temperature Water Test were used. Nb is effective as a stabilizer of C. Consequently to prevent corrosion attack on H A Z in high temperature water Nb should be added more than 100 ( % C - 0.005)% and to maintain mechanical strength, Nb should be added more than 3 + 75( %C + %N)%. Modified alloy 600 satisfying above condition was manufactured commercially and its various properties including weldability were confirmed to be excellent.

UK PubMed Central (United Kingdom)

Measurement of intrathylakoid aqueous volumes by electron spin resonance spectroscopy was used to study ionic permeability properties of thylakoid membranes isolated from Beta vulgaris...Full Text Available

International Nuclear Information System (INIS)

Radiation hardening and radiation-induced chromium (Cr) depletion were related to intergranular stress corrosion cracking (IGSCC) response among various stainless steels (SS). Available data on neutron-irradiated materials were analyzed and correlations developed between fluence, yield strength, grain-boundary Cr concentration, and cracking susceptibility in high-temperature water environments. Large heat-to-heat differences in the critical fluence (0.2 neutrons/cm"2 to 2.5 x 10"2"1 neutrons/cm"2) for IGSCC were documented. Variability often was consistent with yield strength differences among irradiated materials. IGSCC correlated better to yield strength than to fluence for most heats, suggesting a possible role for radiation-induced hardening (and microstructure) on cracking. However, isolated heats revealed a wide range of yield strengths (450 MPa to 800 MPa) necessary to ...

International Nuclear Information System (INIS)

In the present study a partial replacement of aggregate with two different ratios of waste rubber (5%, 10%) with the addition of a constant ratio of rice husk ash (RHA), 5% was carried out. The hardened cement mortar used the optimum water of consistency. The specimens were molded into 1 inch cubic moulds .The specimens were first cured for 24 hours, at 100% relative humidity and then cured under tap water for 3, 7 and 28 days followed by irradiation at different doses of gamma irradiation namely 5 and 10 kGy. The physico-chemical and mechanical properties such as compressive strength, total porosity and bulk density were studied for the three types of specimens. The results showed that the values of the compressive strength, bulk density and chemically combined water of the blended cement mortar paste (OPC-RHA) increase ,while blended cement mortar paste with 5% RHA and 5, 10% ...

Energy Technology Data Exchange (ETDEWEB)

The single-electrode capacitance of a nano-porous carbon electrode used as an electric double layer capacitor was measured. The charged state of the electrolyte ion was discussed from the results. Single-electrode capacitance was not proportional to the specific surface area of the electrode. This implies that the whole surface of the electrode is not effective for the formation of an electric double layer. It is considered that edge orientation of the carbon structure would give a dominant contribution to capacitance. For measurements with aqueous solutions of various electrolytes, capacitance was about the same value for each salt compound. For aqueous acid solution, on the other hand, capacitance was twice to three times as large as that for salt compounds. This difference, however, became negligibly small if the concentration of electrolyte solution was lowered. Taking account of the hydrated ionic radius of each ion, it was considered that ions in salt ...

International Nuclear Information System (INIS)

Several types of corrosion have damaged alloy 600 tubing in the secondary side of steam generators. The types of corrosion include wastage, denting, intergranular attack, stress corrosion, erosion-corrosion, etc. The environments which cause attack may originate from leaks of cooling water into the condensate, etc. When the contaminated feedwater is pumped into the generator, the impurities may concentrate first 200 to 400 fold in the bulk water, depending on the blowdown, and then further to saturation and dryness in heated tube support plate crevices. Characterization of local solution chemistries is the first step to predict and correct the type of corrosion that can occur. The pH is of particular importance because it is a major factor governing the rate of corrosion reactions. The pH of a solution at high temperature is not the same as the ambient temperature, since ionic dissociation constants, solubility and ...

Energy Technology Data Exchange (ETDEWEB)

The Rocky Flats Plant (RFP) generates large volumes of a low level aqueous waste stream high in nitrate salts. The aqueous waste is concentrated by evaporation and then mixed with Portland cement prior to transport and disposal. Planned process upgrades include a new horizontal thin film evaporator. Temperature of brine at discharge end of the new evaporator will be near boiling point. Introduction of hot water to cement can degrade the monolithic waste form. However, the RFP salt waste contains high concentrations of compounds known to retard hydration. This paper discusses impact of introducing high temperature waste to cement. The study evaluated three waste compositions: (1) highest probable nitrate composition, (2) highest probable chloride composition, and (3) current composition. Results showed that compressive strength of final waste form increased with brine temperature, and waste forms from brine at the boiling point exhibited a near ...

International Nuclear Information System (INIS)

This report describes the development of solidification systems for sodium nitrate waste. Sodium nitrate waste was solidified in the polymers polyethylene, polyester-styrene (PES), and water-extendible polyester-styrene (WEP). Evaluations were made of the properties of waste forms containing various amounts of sodium nitrate by leaching immersion in water, measuring compressive strengths and by the EPA Extraction Procedure. Results of the leaching test are presented as cumulative fraction leached (CFL), incremental leaching rate, and average leaching indices (LI). For waste forms containing 30 to 70 wt% sodium nitrate, the CFL ranged from 9.0 x 10"-"3 to 7.3 x 10"-"1 and the LI from 11 to 7.8. After ninety days immersion in water, the compressive strengths ranged from 720 psi to 2550 psi. The nitrate releases from these samples using the EPA Extraction Procedure were below 500 ppM. ...

Science.gov (United States)

... THE STRENGTH, TOUGHNESS, AND STRESS-CORROSION CRACKING SUSCEPTIBILITY OF A METASTABLE BETA TITANIUM ALLOY (Ti-11. ...

Energy Technology Data Exchange (ETDEWEB)

Ionic conductive materials are of much interest as an electrolyte for solid-state lithium batteries. Poly(alkylene oxide) and lithium salt complex exhibits high ionic conductivity in terms of its high solubility for lithium salts. However, the temperature dependency of its ionic conductivity is quite large and non-linear, the ionic conductivity drops down at low temperature, especially below glass transition temperature of the polymer. Because its ionic conductive mechanism is derived from its segmental motion of polymer main chain. A novel ionic conductive material, poly[2,6-dimethoxy-N-(4-vinylphenyl)benzamide] is synthesized and confirm ionic conductivity even below glass transition temperature. Ionic conductivity of the polymer with lithium ditrifluoromethylsulfonate imide complex shows 10{sup -5}Scm{sup -1} from 0 ...

Energy Technology Data Exchange (ETDEWEB)

Nuclear testing at and around the Nevada Test Site (NTS) resulted in widespread contamination from transuranic and other radionuclides, as well as from other toxic inorganic and organic contaminants. The type of contamination, including spatial distribution and type of radionuclides present, depends on the type of testing performed. Remediation of the contaminated areas is currently under way. The optimum in situ or ex situ remediation technology depends on the degree of interaction between the particular radionuclide, or contaminant in general, and the soil matrix, among other factors. The objective of this project was to evaluate the sorption affinity of NTS soils for common non-transuranic radionuclides. The sorption of cobalt (Co) on soils from two different areas of the NTS, namely the Little Feller and Cabriolet event sites, was studied. Experiments were conducted as a function of pH, solid concentration, total Co concentration, ionic ...

Energy Technology Data Exchange (ETDEWEB)

A large part of mechanical and durability characteristics of cement-based materials comes from the performances of the hydrated cement, cohesive matrix surrounding the granular skeleton. Experimental studies, in situ or in laboratory, associated to models, have notably enhanced knowledge on the cement material and led to adapted formulations to specific applications or particularly aggressive environments. Nevertheless, these models, developed for precise cases, do not permit to specifically conclude for other experimental conclusions. To extend its applicability domain, we propose a new evolutive approach, based on reactive transport expressed at the microstructure scale of the cement. In a general point of view, the evolution of the solid compounds of the cement matrix, by dissolutions or precipitations, during chemical aggressions can be related to the pore solution evolution, and this one relied to the ionic exchanges with the external environment. By the ...

International Nuclear Information System (INIS)

The foils of various materials were irradiated with "6"0Co with an activity of 11,538 TBq. The minimum radiation dose was 25 kGy. Changes in chemico-physical properties were evaluated by infrared spectroscopy and were not detected after irradiation with 25 kGy. Packing foils were subjected to the following tests: mechanical tests, tests of weld strength, tests of impact resistance, free fall tests, permeability tests for water vapour and microbiological tests. The results of all tests were tabulated. The tests showed that the foils are impermeable for microorganisms and provided the welds are airtight the packed products remain sterile. (J.P.).

British Library Electronic Table of Contents (United Kingdom)

The age hardening behavior of Al-4.5%Cu alloy composite reinforced with zircon sand particulates and produced by stir casting route has been investigated in different quenching media viz, water, oil, and salt brine solution (7wt%). Optical microscopy of the as cast alloy composite indicates that the matrix of the composite has the cellular structure. Copper rich CuAl2 precipitates have been found near particle matrix interface. The results of ageing demonstrate that the microhardness of age hardenable Al-Cu based alloy composites depend on the quenching medium in which they are heat treated. Salt brine quenching is faster as compared to water and oil, even if higher strength is obtained but cannot be used for complex shapes and thin sections where oil quenching is the alternative due to mi...

British Library Electronic Table of Contents (United Kingdom)

A novel electrogenerated chemiluminescence (ECL) sensor based on natural clay and ionic liquid was fabricated. Tris(2,2prime-bipyridine)ruthenium(II) (Ru(bpy)32+) was immobilized on natural clay surface through simple adsorption. An ECL sensor was prepared by mixing Ru(bpy)32+-incorporated clay, graphite powder and an ionic liquid (1-butyl-3-methylimidazolium hexafluorophosphate) as the binder. The electrochemical behavior and ECL of the immobilized Ru(bpy)32+ was investigated. It was observed that the ECL of immobilized Ru(bpy)32+ was activated by the ionic liquid. The proposed ECL sensor showed high sensitivity to tri-n-propylamine (TPrA) and the detection limit was found to be 20 pM. In addition, the ECL sensor displayed good stability for TPrA detection and long-term storage stability.

Energy Technology Data Exchange (ETDEWEB)

Tannin gel particles that have extremely high adsorption capacity for hexavalent chromium Cr(VI) have been developed by controlling gelation of Mimosa tannin extracted from the bark of plants. The gelation process is composed of two stages; partial gelation of Mimosa tannin by reaction with formaldehyde (cross-linking agent) and granulation by dispersing the partially gelated solution into a liquid mixture of decalin ad a polyether nonionic surfactant with vigorous stirring. The structure of the tannin gel particles is controlled by a combination of operating conditions such as reaction time and temperature at both stages. The water content of the tannin gel particles that reflects their structure can be widely changed from 40 to 79 %(wet basis), even for a constant composition of 23 g Mimosa tannin and 6 ml formaldehyde (37 wt %). It is found that it is very important to increase the water content without losing mechanical ...

Science.gov (United States)

Ultimate compressive strength in the longitudinal direction. (3. Ultimate tensile strength in the transverse direction. U'. Ultimate compressive strength in ...

Energy Technology Data Exchange (ETDEWEB)

The processing characteristics, tensile properties, and oxidation response of two Nb-Ti-Al-Cr alloys were investigated. One creep test at 650 C and 172 MPa was conducted on the base alloy, which contained 40Nb-40Ti-10Al-10Cr. A second alloy was modified with 0.11 at.% C and 0.07 at.% Y. Alloys were arc melted in a chamber backfilled with argon, drop cast into a water-cooled copper mold, and cold rolled to obtain a 0.8-mm sheet. The sheet was annealed at 1,100 C for 0.5 h. Longitudinal tensile specimens and oxidation specimens were obtained for both the base alloy and the modified alloy. Tensile properties were obtained for the base alloy at room temperature, 400, 600, 700, 800, 900, and 1,000 C and for the modified alloy at room temperature, 400, 600, 700, and 800 C. Oxidation tests the base alloy and modified alloy, as measured by weight change, were carried out at 600, 700, 800, and 900 C. Both the base alloy and the modified alloy were extremely ductile and were ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... The ultimate compressive strength (UCS) for the HMU/BSG composite is essentially equivalent to the tensile strength exhibited by this system. ...

Energy Technology Data Exchange (ETDEWEB)

Research commenced in FY 97 to determine the suitability of superplasticized cement-sand grouts for backfilling vertical boreholes used with geothermal heat pump (GHP) systems. The overall objectives were to develop, evaluate and demonstrate cementitious grouts that could reduce the required bore length and improve the performance of GHPs. This report summarizes the accomplishments in FY 98. The developed thermally conductive grout consists of cement, water, a particular grade of silica sand, superplasticizer and a small amount of bentonite. While the primary function of the grout is to facilitate heat transfer between the U-loop and surrounding formation, it is also essential that the grout act as an effective borehole sealant. Two types of permeability (hydraulic conductivity) tests was conducted to evaluate the sealing performance of the cement-sand grout. Additional properties of the proposed grout that were investigated include bleeding, shrinkage, bond ...

International Nuclear Information System (INIS)

Sodium silicate is vacuum impregnated in bauxite waste (red mud) at room temperature to develop ceramics of mechanical properties comparable to the sintered ceramics. For a concentration up to 10% the fracture toughness increases from 0.12 MNm"-"3"/"2 to 0.9 MNm"-"3"/"2, and the compressive strength from 7 MNm"-"2 to 30 MNm"-"2. The mechanical properties do not deteriorate, when soaked in water for an entire week. The viscosity and the concentration of the silicate solution are crucial, both for the success of the fabrication and the economics of the process. Similar successful results have been obtained for bauxite and lime stone, even though the latter has poor weathering properties. With scanning electron microscopy and energy dispersive analysis, an attempt is made to identify the crystals formed in the composite, which are responsible for the strength. The process is an economic alternative to the sintered ceramics in ...

Energy Technology Data Exchange (ETDEWEB)

North Dakota Concrete Products Company uses a steam curing process that accelerates the concrete curing so that 28-day strength is obtained within 24 hours. The cost of energy required to accomplish this is significant, amounting to approximately $80,000 in 1980. The present boilers are oil fired. Recently, fuel oil prices have increased substantially. Further, supply shortages in the past have threatened plant production. The purpose of this study was to evaluate the economic feasibility of using deep formation warm water as an alternative energy source. A water-to-water heat pump system to replace the existing boiler system was investigated. TPI, Inc. economic and engineering findings for this particular potential geothermal application are disclosed. The operating cost savings of the geothermal system over the operating costs of the existing oilfired system would be insufficient to provide an acceptable rate of return on ...

International Nuclear Information System (INIS)

According to the present concept, the low and intermediate level wastes generated during the Cernavoda NPP operation will be disposed in a near surface repository. The Saligny site, placed in the NPP protected area, has been proposed for their disposal. Geologically, the main components of this site are the quaternary loess, the Precambrian and Pre-quaternary clays, the Eocene and Barremian limestone. Hydrologically, the site can be divided into a vadose zone down to 45-50 m and three distinct aquifers, two of them in the limestone beds and the third in the lenses of sand and limestone existing in the pre-quaternary clay layer. A large research program for site characterization was initiated in 1996. At present, the site characteristics requested for safety analysis have been experimentally measured on soil samples or calculated by different computer programs. Hundreds of experimental values of the density, porosity, hydraulic conductivity, soil-water retention, ...

Energy Technology Data Exchange (ETDEWEB)

This work proposes an innovative blend of potassium carbonate (K{sub 2}CO{sub 3}) and piperazine (PZ) as a solvent for CO{sub 2} removal from combustion flue gas in an absorber/stripper. The equilibrium partial pressure and the rate of absorption of CO{sub 2} were measured in a wetted-wall column in 0.0 to 6.2 m K{sup +} and 0.6 to 3.6 m PZ at 25 to 110 C. The equilibrium speciation of the solution was determined by {sup 1}H NMR under similar conditions. A rigorous thermodynamic model, based on electrolyte non-random two-liquid (ENRTL) theory, was developed to represent equilibrium behavior. A rate model was developed to describe the absorption rate by integration of eddy diffusivity theory with complex kinetics. Both models were used to explain behavior in terms of equilibrium constants, activity coefficients, and rate constants. The addition of potassium to the amine increases the concentration of CO{sub 3}{sup 2-}/HCO{sub 3}{sup -} in solution. The buffer reduces protonation of the ...

Energy Technology Data Exchange (ETDEWEB)

This paper discusses spectral change in brown coal and bituminous coal as a result of low-temperature drying. The experiment used a Fourier transform infrared (FT-IR) spectroscopy disposed with an in-situ diffuse reflector as a water content measuring method. The FT-IR spectra of coal showed the existence of two types of adsorbed water. One of the two spectral peaks was thought to have been caused by isolated water molecules which may have been hydrogen bonded to hydrocarbon in the coal molecules and weakly bound. The other peak was thought to have been caused by water which may have been hydrogen bonded to functional groups such as hydroxyl groups in the coal molecules and strongly bound. Drying behavior in brown coal and bituminous coal showed the absorption peak at 3640 cm[sup -1] reducing faster than the absorption peak at 3360cm[sup -1]. Depressurized drying was found to be more effective than ...

British Library Electronic Table of Contents (United Kingdom)

In this paper we review and classify the various patterns of isosteric heat versus loading for adsorption of gases on graphitised thermal carbon black at temperatures ranging from below the 3D triple point to temperatures above it, but less than the 3D critical point. We have identified the features of heat curve and highlighted the microscopic origin of these features. The patterns vary with temperature and with the relative strength of the fluid-fluid interaction and solid-fluid interaction. For simple adsorptives (by simple we meant there is no strong association between fluid particles), the heat curve is typified by fluid-fluid attraction and layering phenomena. For adsorptives showing strong association such as water, ammonia and methanol, the heat curve essentially begins below the ...

Science.gov (United States)

The calculations of Gay et al. of the terminal velocities of charged hydrormeteors in the presence of electric fields have formed the basis of computations of the charging current density J flowing through a thunder-cloud as a result of the operation of a precipitative mechanism of cloud electrification. Values of J were calculated for a range of values of field strength E, precipitation rate pO, precipitation content L, cloud water content C, charge distribution, total separated charge, and the fraction of the small particles that have undergone a charging event.It is found that the estimated field required for the initiation of a lightning stroke (3.5 kV cm1 can be achieved only over a narrow range of conditions. The ease with which precipitative mechanisms can produce breakdown fields is considerably increased, however, if account is taken of spatial inhomogenities in the field.

Energy Technology Data Exchange (ETDEWEB)

A formulation to pelletize simulated high-level ICPP alumina waste calcine was developed. The pellets are formed on a 41-cm-diameter disc pelletizer using 5% bentonite, 2% metakaolin, and 5 wt % calcium hydroxide as a solid binder and a solution of 7M phosphoric acid and 4M nitric acid as a liquid binder. After drying and heat treatment at 800/sup 0/C for 2 hours, the average crush strength of the pellets is 3.9 MPa and the pellets have a leach resistance of 10/sup -3/ g/cm/sup 2//day, based on Soxhlet leaching for 48 h at 95/sup 0/C with distilled water.

British Library Electronic Table of Contents (United Kingdom)

The physical and antioxidant properties of alginate biodegradable film incorporating white, red and extruded white ginseng extracts were investigated. No differences in moisture contents of all alginate film samples were noticeable (p>0.05) except those film samples incorporated without ginseng extract, which had the highest moisture content. The addition of ginseng extract to alginate film decreased tensile strength and elastic modulus (p<0.05) but increased the percent elongation at break. The presence of extracts did not significantly affect the water vapor permeability of the film samples. Alginate film containing extruded white ginseng extract at a barrel temperature of 130degreeC presented the highest (61.12%) free-radical scavenging activity against the 2,2-diphenyl-1-picryhydrazyl ...

British Library Electronic Table of Contents (United Kingdom)

In recent years, offshore reservoirs have been developed in deeper and deeper water environments. Steel catenary risers (SCRs) are being considered in deepwater development such as Northern North Sea. SCRs used in conjunction with a semi-submersible or floating production, storage and offloading (FPSO) in deepwater harsh environments present significant design challenges. The large vertical motions at the semi or FPSO induce severe riser response, which results in difficulty meeting strength and fatigue criteria at the hang off and touch down point locations. To improve the understanding of SCR behaviour and increase the confidence in the design of such systems in deepwater harsh environments, a parametric study on a SCR connected to a semi-submersible was carried out in this paper to deal...

Energy Technology Data Exchange (ETDEWEB)

Donnan dialysis with ion-exchange membranes was studied under various kinds of experimental conditions using ions of different valences. The diffusion coefficients (D{sub d}) of various kinds of ions in the ion-exchange membrane were obtained by curve fitting an equation derived from the mass balance to three kinds of Donnan dialytic experiments. It was found that the value of D{sub d}/D{sub s} using D{sub d} of monovalent ions in Donnan dialysis with a set of monovalent feed ions and bivalent driving ions was 1/175, where D{sub s} represents a diffusion coefficient in solution. D{sub s} was calculated from the Nernst-Einstein equation substituted by the ionic conductance of ions at infinite dilution in water. Using D{sub d} of bivalent ions in Donnan dialysis with the same set led to a D{sub d}/D{sub s} value of 1/438. Moreover, using D{sub d} in Donnan dialysis with the same set, the value of D{sub d}/D{sub e} was kept constant at 0.4 (D{sub ...

International Nuclear Information System (INIS)

An effective method of enhancing charge injection and electroluminescence efficiency of polymer-based light emitting diode is introduced. Spin-coated films of poly (N-vinylcarbazole) blended with electron-transport material (Bu-PBD), laser dye (Coumarin6), and the typical supporting electrolyte (tetraethylammonium perchlorate; TEAP) were examined and it was found that the injection current and luminance of the light emitting diode doped with TEAP were enhanced dramatically after heat-treatment at 80 deg. C and appropriate biasing in an external electric field of 1.5x10"8 V/m at this temperature. The thermally stimulated current (TSC) was also measured to investigate the relaxation process of ionic space charges in the films. The relaxation times of ionic polarization were found to be related to the cation size of the electrolyte. And the relaxation time becomes long enough by the use of TEAP doping.

Science.gov (United States)

Transition-metal chemistry in ionic liquids (IL) has achieved intrinsic fascination in the last few years. The use of an IL as environmental friendly solvent, offers many advantages over traditional materials synthesis methods. The change from molecular to ionic reaction media leads to new types of materials being accessible. Room-temperature IL have been found to be excellent media for stabilising transition-metal clusters in solution and to crystallise homo- and heteronuclear transition-metal complexes and clusters. Furthermore, the use of IL as solvent provides the option to replace high-temperature routes, such as crystallisation from the melt or gas-phase deposition, by convenient room- or low-temperature syntheses. Inorganic IL composed of alkali metal cations and polynuclear transition-metal cluster anions are also known. Each of these areas will be discussed briefly in this contribution. PMID:21743925

Energy Technology Data Exchange (ETDEWEB)

Chemical admixtures are used in dam construction to improve plasticity of the dry materials mixture over time. Roller compacted concrete (RCC) has been used on many dam projects in China. However, the use of RCC has frequently resulted in water reduction problems. This paper provided details of an admixture based on polycarboxylate ether (PCE) which was developed to improve the quality of RCC constructions at the JinHong dam in China. Use of the polymer at the JinHong dam resulted in a vibration sensitive concrete that was sustained over time. Under identical mix-design and compaction conditions in the laboratory, specific gravity of the RCC was increased from 2417 kg/m{sup 3} to 2463 kg/m{sup 3}. The high specific gravity of the material resulted in satisfactory strength data from the dam project. The key-ratio of the splitting tensile strength versus compressive strength was higher than 8 per cent in ...

International Nuclear Information System (INIS)

The present design of Blanket Shield and Primary Wall for ITER envisages construction of the wall with a water cooled, stainless steel outer layer and a water cooled, copper liner on the inside plasma facing surface. Protection of the inner copper surface with an armour layer is necessary to cope with plasma to wall interaction. There are a number of armour materials under consideration, for this project beryllium was used. The scope of work was to produce a series of mock-ups, each consisting of a different combination of materials, which included Dispersion Strengthened Copper, Copper-Chrome-Zirconium alloy, Beryllium and Stainless Steel. Hot Isostatic Pressing (HIP) was the method used to ensure that a fully diffused bonded joint was achieved giving the necessary strength and thermal conductivity. The first five of the mock ups have been successfully completed and are being tested at the various laboratories in Europe. ...

International Nuclear Information System (INIS)

The properties of wood plastic composites (WPC) based on Pinus Radiata D. Don impregnated with methylmethacrylate and subsequently polymerized with gamma radiation were studied. Different systems of impregnation were utilized, in order to obtain partial and shell loads. The minimum irradiation dose uses was 16 kGy. The following tests were made to the material: static bending, compression strenght parallel to grain, hardness, sheer strength, toughness, water absorption, dimensional stability and flame propagation index. To evaluate the testing, the results of the samples were separated according final density in the ranges: R_1 = 429-483 kg/m3 (without treatment); R_2 = 500-650 kg/m3 and R3 = 651-850 kg/m3. In general, the best results were obtained for samples of high density. The most important results were achieved for dimensional stability, water absorption and hardness. (Author).

Energy Technology Data Exchange (ETDEWEB)

Fatigue damage occurs in general when a boiler tube is subject to repeat cyclic or fluctuating loading although the stress produced is below the material yield strength. The types of fatigue damage include, e.g., corrosion, thermal, mechanical, vibration, and creep fatigue. It is important to determine which form of fatigue is active, because measures to avoid repeat failures differ as the case arises. In this lesson, the focus is exclusively on corrosion fatigue. Corrosion fatigue occurs by the combined synergistic actions of cyclic loading and a corrosive environment. It is a discontinuous process with crack initiation and growth during transient periods. The excessive stresses may be caused during boiler operation by the restraint at tube attachments and by load changes (in particular during cold starts or forced cools) or during shutdown or restart of circulation boilers by thermal stratification of water along the tube length. Poor ...

UK PubMed Central (United Kingdom)

The storage and distribution of copper, cadmium, and uranium and their effects on ionic contents in roots and shoots of Azolla filiculoides has been studied by x-ray microanalysis....Full Text Available

UK PubMed Central (United Kingdom)

A synthetic strategy for constructing ionic hydrogen-bonded materials by combining perhalometallate anions with cations able to serve as hydrogen bond donors is presented. The approach is based on identification...Full Text Available

International Nuclear Information System (INIS)

Calculations, drawing principally on developments at AERE Harwell, of the relaxation about lattice defects are reviewed with emphasis on the techniques required for such calculations. The principles of defect modelling are outlined and various programs developed for defect simulations are discussed. Particular calculations for metals, ionic crystals and oxides, are considered. (UK).

UK PubMed Central (United Kingdom)

Purified cell walls were prepared from roots of Horse bean (Vicia faba L., var. minor) and Yellow Lupine (Lupinus luteus L.). Two methods were used:...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

New lithium ion composite electrolyte, LiI?Li2S?La2O2Sm (m=1, 2) was synthesized from the binary Li2S?LaOI system through solid state reaction. The lithium ion conductive property was investigated by AC impedance spectroscopy. And the highest conductivity of the obtained electrolyte at room temperature was found to be 3.0?10?6?S cm?1. The notable ionic conduction was attributed to the in situ formed amorphous LiI.

UK PubMed Central (United Kingdom)

If bone strength was the only requirement of skeleton, it could be achieved with bulk, but bone must also be light. During growth, bone modelling and remodelling optimize strength, by depositing bone...Full Text Available

Science.gov (United States)

... Accession Number : ADD151811. Title : Ultra High Strength Beta Titanium Alloy for Fasteners. Descriptive Note : Journal article,. ...

Science.gov (United States)

... 500 ppm, boron increases the 0.2% offset strength; results show that boron doping does not appreciably affect ultimate compressive strength; for 0 ...

Science.gov (United States)

Ultimate compressive strength and failure modes were studied using 24- ... to 81 % of the average ultimate compressive strength (UCS). Figure 1 (a) is the failure ...

Science.gov (United States)

... Abstract : The ultimate compressive strength of Conolon 506 increases from 39,200 psi at +78F to 57,100 psi at -320F. ...

International Nuclear Information System (INIS)

A cross-flow atmospheric plasma jet with distilled water or analyte solution nebulization has been investigated. The plasma gas flows perpendicularly to the RF powered electrode (11.21 MHz) and a grounded electrode was added for plasma stabilization. The working parameters of the plasma generator can be controlled in order to maximize either the plasma power (75 W) or the voltage on the RF powered electrode (plasma power, 40 W). The plasma gas, pure argon (0.4 l min-1) or a mixture of argon (0.3-0.4 l min-1) and helium (0-0.2 l min-1), was also used for liquid nebulization. Optical emission of the plasma, collected in the normal viewing mode, was used for plasma diagnostics and for evaluating its excitation capabilities. The influence of helium content in the mixed-gas plasma on the plasma characteristics and on the emission axial profiles of the plasma gas constituents and of the analytes originate from the wet aerosol was studied. The addition of helium to the ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

PMID:10831980

Science.gov (United States)

PMID:9189200

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Clean Water Act You are here: Water Laws & Regulations Policy & Guidance Clean Water Act Water Quality and 401 Certification Water Quality and 401 Certification Water Quality...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the development, design, and fabrication of the crude oil process facilities, and the conversion of an existing tanker for use at the Liuhua 11-1 Field. Over a 16-month period spanning 1994 and 1995, Amoco Orient Petroleum Company, and partners, China Offshore Oil Nanhai East Corporation (CONHE), and Kerr-McGee China Petroleum Ltd., converted a crude oil tanker originally built in 1975 to the Nanhai Sheng Li, the floating production, storage and offloading (FPSO) facility for the Liuhua 11-1 Field. The FPSO will process up to 65,000 BOPD produced from 20 subsea wells located 1.7 miles away. In addition to the processing facilities for produced oil and water, the FPSO has a processed crude oil storage capacity of 715,000 bbls. The ship`s propulsion system was removed during the conversion, because the FPSO is permanently moored at site by means of a 10-point, ``soft`` mooring. The mooring system was designed to survive the 100-year-return-period ...

Energy Technology Data Exchange (ETDEWEB)

A precise admixtures system is needed when using high-volume fly ash concrete as fresh concrete occasionally undergoes rapid slump loss after mixing, which can cause problems with casting, pumping and finishing of the concrete in hot weather. This paper provided details of a study conducted to implement high-volume fly ash concrete technology in India. Different families of admixtures were investigated to determine their water reduction capacities. A set-retarding admixture was used in some of the concrete mixtures in order to determine its efficacy. An Indian Portland cement was used to create a total of 22 different concrete mixtures. Four different fly ashes were used to replace portions of the concrete. The slump of the fresh concrete mixture was monitored for 2 to 3 hours. Unit weight and temperature of the concrete was measured. Specimens were cast in steel moulds in order to determine the compressive strength and unit weight of the ...

Science.gov (United States)

Extensive laboratory and industrial tests are being conducted at the Western Siberian Iron and Steel Works (I and SW) on the adoption of preheating of coking. The present article describes the results of laboratory investigations of the effect of the free oxygen content in the gaseous heat carrier and the final charge preheating temperature on the technological properties of the charge and the quality of the blast furnace coke, as well as the yield and quality of the coking products: 1. An increase in the free oxygen concentration in the heat carrier to 8% degrades the strength properties of the coke - the crushability and abradability are increased. 2. Charge preheating to 200 to 250/sup 0/C, even with a low oxygen concentration in the heat carrier, is accompanied by degradation of the physical and mechanical properties of the coke. 3. The optimal temperature of charge preheating before coking at the Western Siberia I and SW was found to be in the 150 to 200/sup ...

Energy Technology Data Exchange (ETDEWEB)

A porous tooling system was selected for the processing of Graphite/PMR-15 Polyimide laminates in thickness up to 3.2 mm. (0.125 inch). This tool system must have a reasonable strength, permeability dimensional stability, and thermal conductivity to accomplish curing at 600 F and 200 psi and 200 psi autoclave temperature and pressure. A permeability measuring apparatus was constructed and permeability vs. casting water level determined to produce tools at three different permeability levels. On these tools, laminates of 5, 11, and 22 plies (.027, .060, and 0.121 inch) were produced and evaluated by ultrasonic, mechanical, and thermal tests to determine the effect of the tool permeability on the cured laminates. All tools produced acceptable laminates at 5 and 11 plies but only the highest permeability produced acceptable clear ultrasonic C-Scans. Recommendations are made for future investigations of design geometry, and strengthening techniques ...

Energy Technology Data Exchange (ETDEWEB)

The excellent high temperature strength and thermal conductivity of molybdenum-base alloys provide attractive features for components in advanced magnetic and inertial fusion devices. Refractory metal alloys react readily with oxygen and other gases. Oxidized molybdenum in turn is susceptible to losses from volatile molybdenum trioxide species, (MoO3)m, in air and the hydroxide, MoO2(OH)2, formed from water vapor. Transport of radioactivity by the volatilization, migration, and re-deposition of these volatile species during a potential accident involving a loss of vacuum or inert environment represents a safety issue. In this report we present experimental results on the oxidation, volatilization and re-deposition of molybdenum from TZM in flowing air between 400 and 800°C. These results are compared with calculations obtained from a vaporization mass transfer model using chemical thermodynamic data for vapor pressures of MoO3(g) over ...

International Nuclear Information System (INIS)

Even as the recession begins to subside, the energy sector is still likely to experience challenging conditions as we enter 2011. It should be remembered how very important a role energy plays in driving the global economy. Serving as a simple yet global and unified measure of economic recovery, it is oil's price range and the strength and sustainability of the recovery which will impact the ways in which all forms of energy are produced and consumed. The report aims for a closer insight into these predictions: What will happen with M and A (Mergers and Acquisitions) in the energy industry?; What are the prospects for renewables?; Will the water-energy nexus grow in importance?; How will technological leaps and bounds affect E and P (exploration and production) operations?; What about electric cars? This is the second year Deloitte's Global Energy and Resources Group has published its predictions for the year ahead. The report is based on ...

Energy Technology Data Exchange (ETDEWEB)

This paper indicates first that the base content in desert soil is by far much higher than that in soils in moist areas, that salts with the higher solubility to water have their deposition depth greater, and that the organic content is extremely low. The paper also describes the experiments to verify that the desert soil contains soil lumps with a diameter of about several millimeters, which function effectively to form the long term survival locations for microorganisms. Desert soil containing soil lumps and the one removed of lumps by pulverizing them into powder were prepared as test specimens, which were left submerged. It was confirmed that the velocity of decomposing the organics and the mechanical strength in the latter soil are obviously inferior to those in the former soil. Additional remarks are given that when the desert soil environment is changed the microorganisms get more active appreciably and that certain kinds of mold fungi ...

Energy Technology Data Exchange (ETDEWEB)

North Slope of Alaska has huge oil deposits in heavy oil reservoirs such as Ugnu, West Sak and Shrader Bluff etc. The viscosity of the last two reservoir oils vary from {approx}30 cp to {approx}3000 cp and the amount in the range of 10-20 billion barrels. High oil viscosity and low formation strength impose problems to high recovery and well productivity. Water-alternate-gas injection processes can be effective for the lower viscosity end of these deposits in West Sak and Shrader Bluff. Several gas streams are available in the North Slope containing NGL and CO{sub 2} (a greenhouse gas). The goal of this research is to develop tools to find optimum solvent, injection schedule and well-architecture for a WAG process in North Slope shallow sand viscous oil reservoirs. In the last quarter, we have developed streamline generation and convection subroutines for miscible gas injection. The WAG injection algorithms are being developed. We formulated a ...

Energy Technology Data Exchange (ETDEWEB)

The object of briquetting coal fines is to convert a low grade fuel into one of superior quality coal. Briquetting techniques make coal an attractive substitute fuel by converting it into a compact, stable and inexpensive fuel. The briquetting of coal fines and char fines from coal and lignite, coke breeze, charcoal fines and similar materials is an important process for producing shaped fuel for a number of uses. Formed-coke made from non-caking coal for use in a blast furnace or in a cupola furnace involves the briquetting of treated char fines and further processing of the briquettes by means of carbonizing and curing. Briquettes may be made with or without binders, brown coal is particularly suitable for briquetting without a binder. Heat treatment may enable a higher rank coal to be briquetted without a binder, but binders are usually used so as to improve the combustion properties of the coal, they may include pitch, bitumen, sulphite liquor, starches and lime. Briquettes are ...

Science.gov (United States)

New methodologies for fabrication of multilevel packaging, particularly for RF signal analysis, are investigated. A new method for ``gluing'' silicon wafers together with a Self Assembled Monolayers (SAMs) based nanoglue are discussed, as are methods to enable its use with nonconforming wafers. Results of bond strength measurements as a function of temperature and process will be presented. Surface area bonded is characterized by infrared (IR) imaging. We will also present a method of inducing self-alignment between whole silicon wafers with micrometer precision. This represents a qualitative departure from alignment of millimeter-sized object as has been previously demonstrated. Self-alignment is induced by creating hydrophilic and hydrophobic regions on the wafers and using capillary forces of water in these regions to force the wafers to align with little to no outside influence. Results are characterized by IR imaging. Physical ideas that ...

Science.gov (United States)

Simple and low cost biosensor based on screen-printed electrode for sensitive detection of some alkylphenols was developed, by entrapment of HRP in a nanocomposite gel based on single-walled carbon nanotubes (SWCNTs) and 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF(6)]) ionic liquid. Raman and FTIR spectroscopy, CV and EIS studies demonstrate the interaction between SWCNTs and ionic liquid. The nanocomposite gel, SWCNT-[BMIM][PF(6)] provides to the modified sensor a considerable enhanced electrocatalytic activity toward hydrogen peroxide reduction. The HRP based biosensor exhibits high sensitivity and good stability, allowing a detection of the alkylphenols at an applied potential of -0.2V vs. Ag/AgCl, in linear range from 5.5 to 97.7?M for 4-t-octylphenol and respectively, between 5.5 and 140?M for 4-n-nonylphenol, with a response time of about 5s. The detection limit was 1.1?M for 4-t-octylphenol, and respectively 0.4?M for ...

Energy Technology Data Exchange (ETDEWEB)

Since ionic liquids (ILs) possess several attractive properties, including chemical and thermal stability, nonflammability, high ionic conductivity, and negligible vapor pressure, a new electrolyte system based on ILs has been proposed for chip type aluminum electrolytic capacitors. Four ILs based on imidazolium/pyrrolidinium cations and maleate/phthalate anions have been synthesized and their thermal stabilities have been examined. The 25wt.% solutions of the four ILs in gamma-butyrolactone (GBL) solvent were prepared as electrolytes of chip type aluminum electrolytic capacitors. The conductivity, sparking voltage and thermal stability of these electrolytes have been systematically investigated. The results revealed that the four IL-based electrolytes exhibited high conductivity. Furthermore, the conductivity of maleate anion-based electrolytes is higher than that of phthalate anion-based electrolytes, whereas the high-temperature durability ...

Energy Technology Data Exchange (ETDEWEB)

Samples of austenitic stainless steel AISI 316 were nitrided using the cathodic cage technique with the addition of methane in the nitriding atmosphere. The aim was to study the influence of this technique in reducing the precipitation of chromium nitrite and in improving the wear resistance. The results show that there was a significant improvement in such properties when compared to the results of ionic plasma nitriding. Formation of a double layer, one more internal composed of carbon and another with high nitrogen content, was confirmed by Scanning Electron Microscopy (SEM). The microhardness profile of the layer showed an increase in hardness values and a larger uniformity, while X-ray analysis showed less chromium nitriding precipitation when compared with results obtained for samples treated using ionic plasma nitriding.

Energy Technology Data Exchange (ETDEWEB)

Ultra-thin, uniform, pinhole-free solid polymer electrolyte films having a fixed carboxylic ester group of approximately 1 {mu}m thickness were prepared by polymerization of methyl acrylate and tris(2-methoxyethoxy)vinylsilane in a glow discharge plasma. The carboxylic ester group of the plasma polymer were transformed to lithium carboxylate groups by treatment with lithium iodide. This process give a single lithium ion conductive film. These solid polymer electrolyte films showed ionic conductivities of the order of 10{sup -8} S cm{sup -1} (10{sup 4} {omega} cm{sup 2} resistance per unit area) at room temperature. (orig.).

CERN Document Server

In this paper we develop an analytical framework for the study of electrochemical impedance of mixed ionic and electronic conductors (MIEC). The framework is based on first-principles and it features the coupling of electrochemical reactions, surface transport and bulk transport processes. We utilize this work to analyze two dimensional systems relevant for fuel cell science via finite element method (FEM). Alternate current Impedance Spectroscopy (IS) of a ceria symmetric cell is simulated near equilibrium condition (zero bias) for a wide array of working conditions including variations of temperature and $H_2$ partial pressure on a two dimensional fuel cell sample with patterned metal electrodes. The model shows agreement of IS curves with the experimental literature with the relative error on the impedance being consistently below 2%. Important two-dimensional effects such the effects of thickness decrease and the influence of variable electronic and ...

British Library Electronic Table of Contents (United Kingdom)

Aim:To examine the electrophysiological effects of sophocarpine on action potentials (AP) and ionic currents of cardiac myocytes and to compare some of these effects with those of amiodarone.Methods:Langendorff perfusion set-up was used in isolated guinea pig heart, and responses to sophocarpine were monitored using electrocardiograph. Conventional microelectrode, voltage clamp technique and perforated patch were employed to record fast response AP (fAP), slow response AP (sAP) and ionic currents in guinea pig papillary muscle or rabbit sinus node cells.Results:Tachyarrhythmia produced by isoprenaline (15 ?mol/L) could be reversed by sophocarpine (300 ?mol/L). Sophocarpine (10 ?mol/L) decreased the amplitude by 4.0%, maximal depolarization velocity (Vmax) of the fAP by 24.4%...

Science.gov (United States)

Programs & Services Technical Resources Land Use Soils Water Snow Survey & Water Supply Water Management Water Quality Watersheds Wetlands Air Plants & Animals Energy Climate...

International Nuclear Information System (INIS)

A new high strength titanium alloy has been developed primarily intended for fastener applications. While Ti-6Al-4V is used extensively as a fastener alloy in the aerospace industry, its shear strength allowable is limited to 655 MPa (95 ksi). For higher shear strength requirements, various steels or nickel-based alloys are used (up to 860 MPa (125 ksi)), but with the attendant density penalty. This new alloy is intended to provide the 860 MPa shear strength at roughly a 40% weight savings. After screening various alloy systems, the optimum chemistry has been selected as follows: Ti-6.0V-6.2Mo-5.7Fe-3Al. In light of its 125 ksi shear strength goal, the alloy has been designated TIMETAL reg-sign 125.

Energy Technology Data Exchange (ETDEWEB)

Ribbon parachute fabrics were tested during development and production of a 24 ft parachute, and after 2.5 years ambient exposure at several storage sites. The effects of sewing, packing, and parachute deployment on material strength were obtained in the 1000 lb Kevlar ribbon after moisture exposure during packing, and when packed parachutes absorbed moisture or were thermal cycled. Individual yarn samples from the low strength ribbons exhibited little change in strength indicating that the material itself had not degraded. Factors leading to the change in ribbon strength are discussed. Considering all materials, there have been no indications to date of any uncontrollable changes in material strength that would limit the use of Kevlar in parachute applications.

Energy Technology Data Exchange (ETDEWEB)

Cylindrical shells with regular perforation are widely used in power generating equipment and in particular in collectors 1 of the circuit of steam generators of power generating installations with water-water reactors (WWPR) The state of stress of collectors is determined by a broad spectrum of technological and operational loads, it is therefore difficult to analyze it theoretically. The aim of the present work is the experimental investigation of stresses in the cylindrical shells of collectors subjected to internal pressure, the generalization and systematization of empirical data in the form of engineering formulas and nomographs. The investigations were carried out with photoelastic three-dimensional models with the use of {open_quotes}freezing{close_quotes}. The basic characteristics of the state of stress of perforated shells (in particular those used in calculations of the strength and life of collectors) are the values of the stress ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents ionic conductivity results obtained with polymer electrolytes and also with propylene carbonate solutions. The domain of electrochemical activity of this salt has been determined using cycle volt-amperometry in propylene carbonate. Preliminary experiments on the stability of the polymer electrolyte with respect to the lithium electrode have been carried out for a possible subsequent use in lithium batteries. (J.S.) 4 refs.

International Nuclear Information System (INIS)

Phospholipid vesicles were found to be lysed by exposure to free radicals derived from irradiated glycine and galactose. The decomposition yield increased with vesicle concentration, and attained values of 0.0006 vesicles destroyed per radical added. Ionic charge at the phospholipid end groups was found to be more important than degree of unsaturation in determining this yield. Radicals derived from irradiated serine and alanine had no detectable lytic action at the vesicle concentrations tested.

International Nuclear Information System (INIS)

Intrinsic crossluminescence (CRL) of CsBr, CsCl, and of BaF_2 was investigated with electron-beam and synchrotron radiation excitation. From the CRL spectra, the excitation spectra and the reflectivity, energy level schemes were deduced. Extrinsic CRL was observed changing either the initial (CsCl:Br"-) or the final (RbCl:Cs"+; KCl:Cs"+) state of CRL by doping. (author).

International Nuclear Information System (INIS)

Chemical effects on the intensity ratio of LX-ray of molybdenum compounds irradiated by 11-keV electrons and by 3-MeV protons were studied using an x-ray crystal spectrometer. It was found that the intensity ratios of L_#gamma#_1/L_#beta#_1 markedly decrease with the increase of ionicity of molybdenum compounds, except for the case of metallic molybdenum. (author).

UK PubMed Central (United Kingdom)

The purpose of this study was to determine if there were any beneficial or detrimental effects regarding delayed onset muscle soreness (DOMS), serum creatine kinase (CK), and maximum concentric strength...Full Text Available

UK PubMed Central (United Kingdom)

Isometric/isokinetic muscle strength and isokinetic endurance of the lower extremities as well as aerobic capacity were evaluated in 67 patients (43 female, 24 male; mean age 53 years, range 23-65)...Full Text Available

Science.gov (United States)

... Coupon 119 * 52 Probability of Survival Versus Ultimate Compressive Strength for Un-notched Laminate 1 Coupon ipn ...

International Nuclear Information System (INIS)

Strain rate effects for the high strength, metastable beta-titanium alloy Ti-8Mo-8V-2Fe-3Al are assessed in terms of tensile and fracture toughness behavior. It is shown that as the strain rate increases the yield strength, ultimate tensile strength, and ductility also increase. As a result of the decrease in the amount of intergranular fracture as the strain rate is increased, the dynamic fracture toughness values K/sub Id/ are greater than those obtained under static conditions as given by K/sub Q/.

International Nuclear Information System (INIS)

1970. United States Crossley, FA Lindberg, RW Lockheed Missiles and

Science.gov (United States)

roller bearing strength suffi- cient to support efficient, rolling friction movement, even in the presence of large, resisting forces. ...

Science.gov (United States)

... Problems investigated in various basic hollowness ratios include ultimate compressive strength, fatigue properties, buckling characteristics, and ...

Science.gov (United States)

... populations ..... 63 34 Vertebral ultimate compressive strength for various populations ..... 64 35 ...

Energy Technology Data Exchange (ETDEWEB)

Stress-rupture strength tests were made of metal steam pipe (12Kh1MF steel) in various conditions, the original, after aging under laboratory conditions (580{degrees}C, 10,000 h), and after long service. It was shown that the more the steel is hardened by heat treatment or cold plastic working in the original condition, the less it hardens in creep. It was established that softening in creep of steel with a moderate yield strength is caused primarily by aging and with a high yield strength by pore formation.

Energy Technology Data Exchange (ETDEWEB)

In calculating the strengths of depolarizing resonances it may be convenient to reformulate the equations of spin motion in a coordinate system based on the actual trajectory of the particle, as introduced by Kondratenko, rather than the conventional one based on a reference orbit. It is shown that resonance strengths calculated by the conventional and the revised formalisms are identical. Resonances induced by radiofrequency dipoles or solenoids are also treated; with rf dipoles it is essential to consider not only the direct effect of the dipole but also the contribution from oscillations induced by it.

International Nuclear Information System (INIS)

Cyclic strength of #alpha#+#beta#-titanium alloy BT3-1 is studied under load frequencies of 33 and 300 Hz. The increase in the cyclic strength with growing frequency is caused by formation of FCC interphase layers of titanium hydrides. Their formation is one of possible ways of raising the fatigue strength of titanium alloys. Peculiarities of FCC interlayer formation in #alpha#+#beta# phases under loading frequency variation are revealed.

Science.gov (United States)

for? Learn the Issues Science & Technology Laws & Regulations About EPA Contact Us Water: Water Quality Criteria You are here: Water Science & Technology Surface Water Standards &...

International Nuclear Information System (INIS)

... hydrology norway water pollution pollution scandinavia surface waters

Science.gov (United States)

The bone mineral content of 109 lumbar vertebrae from 36 different subjects was determined by dual photon absorptiometry. The mean age of the subjects was 58.5 years (range, 31 to 79 years). The ultimate strength of the vertebral bodies was determined during axial compression. Bone mineral content and ultimate compressive strength were correlated (r = 0.86) and the strength was found to increase linearly with increasing amounts of bone mineral content. No differences in this correlation were found in the four vertebral levels (L-4) included in the study, but a difference in this correlation was found between specimens taken from male and female subjects. The results make it possible to estimate the strength of a vertebral body from the knowledge of its bone mineral content as determined by dual photon absorptiometry and provide a basis of estimations of normal and abnormal amounts of bone mineral ...

Energy Technology Data Exchange (ETDEWEB)

A new experimental technique to measure material shear strength at high pressures has been developed for use on magneto-hydrodynamic (MHD) drive pulsed power platforms. By applying an external static magnetic field to the sample region, the MHD drive directly induces a shear stress wave in addition to the usual longitudinal stress wave. Strength is probed by passing this shear wave through a sample material where the transmissible shear stress is limited to the sample strength. The magnitude of the transmitted shear wave is measured via a transverse VISAR system from which the sample strength is determined.

Energy Technology Data Exchange (ETDEWEB)

We study fluctuation properties of strength function phenomena by employing a quantum mechanical model where a single parent state couples with a large number of background states. The background system is devised in such a way that the classical dynamics of the system may show a regular, an irregular, or a chaotic character as a function of a single parameter. The coupling of the parent state to the background states produces a fragmentation of the parent state, giving rise to a strength function phenomenon. We study various measures of the strength function that characterize its bulk structure or fluctuation properties. They include energy moments, strength distribution, fractal dimensions of the strength function, and Fourier transform of the autocorrelation function. Some of these measures, such as strength distribution or Fourier transform of the ...

Energy Technology Data Exchange (ETDEWEB)

Volume 2 of the water resources data for the 1992 water year for Oklahoma consists of record of stage, discharge, and water quality of streams; stage, contents, and water quality of lakes or reservoirs; and water levels of ground-water well. The report contains discharge records for 136 gaging stations; stage and contents for 31 lakes or reservoirs; water quality for 50 gaging stations. Also included are 61 partial-record or miscellaneous streamflow stations and 28 ground-water sites.

Energy Technology Data Exchange (ETDEWEB)

Mechanical properties, flow characteristics and chemical resistance of polycarbonate (PC)/polybutylene terephthalate (PBT)/impact modifier (IM) blends were investigated over the various composition ranges of PC and PBT. Mechanical properties of the PC/PBT/IM blends for different IMs, butadiene based IM and butyl acrylate based IM, were studies for various compositions of the IMs. Impact strength at low temperature was also observed. For the study of chemical resistance of the PC/PBT/IM blends, the blends were dipped in organic solvent, thinner, and then variations of mechanical properties were analyzed. Tensile and flexural strengths were increased linearly and heat distortion temperature (HDT) also increased as PC content in the blends increased. Impact strength increased drastically as PC content increased up to 50 wt% and stayed stable value. Flowability decreased as PC content increased. impact ...

International Nuclear Information System (INIS)

The performance of larger than bench scale ion exchange systems is evaluated by using solutions containing trace amounts of "1"3"7Cs, "8"5Kr, and "1"3"1I, and large amounts of either NaCl or Na_2HPO_4, H_3BO_3, and LiOH. The significant finding in this study is that the empirical rules of ionic selectivity of strong acid cation and strong base anion resins were followed by all ionic species, even though concentrations of some macrocomponents were nearly 10"6 times those of trace components. Other results of possible importance are the correlation between the instantaneous decontamination factor (DF) and the efficiency of column exchange capacity utilization, and the concept of time average decontamination factor (anti DF). The plot of anti DF vs. feed throughput will serve as a guide in determining when the feed should be discontinued in order to achieve a desired anti DF. Both of these correlations are derived from the breakthrough curves.

International Nuclear Information System (INIS)

Li_1_._3Al_0_._3Ti_1_._7(PO_4)_3 thin films were successfully prepared by the solution deposition using lithium acetate, aluminum nitrate, ammonium dihydrogen phosphate and titanium butoxide as starting materials. The structure, surface morphology, electrochemical window, and ionic conductivity of the films were studied by X-ray diffraction, scanning electron microscopy, cyclic voltammetry and AC impedance. The results showed that Li_1_._3Al_0_._3Ti_1_._7(PO_4)_3 thin films annealed between 750 deg. C and 900 deg. C prepared by this method were well crystallized, homogenous and crack-free. The electrochemical window was beyond 2.4 V and the ionic conductivity was approximately 1.57x10"-"5 S/cm at room temperature for the film annealed at 800 deg. C for 30 min.

Energy Technology Data Exchange (ETDEWEB)

For the development of high ionic conductive solid electrolyte, LiTi2(PO4)3 (LTP), one of the promising inorganic solid electrolyte, was synthesized to investigate an effect of additional lithium salt on the ion conductivity. Lithium salt added LTP composite electrolyte sintered at 900{degree}C exhibited highest conductivity, which was two order magnitude higher than pure LTP. Effects of lithium salt addition are as follows. Conductivity of the composite electrolyte provided larger sintering temperature dependence than the pure LTP. From X-ray diffraction analysis, structures and compositions were resemble between two composite electrolytes. Byproducts except LTP provided rather low conductivity. It was suggested that melted constitution in the composite can affect the sintering improvement by the additional lithium salt at temperatures over 800 {degree}C. From the observation of ruptured surface of sintered specimens, grain growth was found only for the composite ...

International Nuclear Information System (INIS)

Liquid-liquid extractive separation of lithium isotopes was carried out in order to investigate the fluctuation of separation factors (a) as a function of salt concentrations in an aqueous phase. Two equations for separation factor (a_o_b_s) as a function of the concentration were introduced; one for the diluted region, and another for the concentrated region. In the former solution where hydrated lithium ions are predominant, 1n a_o_b_s = Ac + B, and in the latter where ion-pairs with anions are predominant, 1n a_o_b_s = Dc + E(c - F)"1"/"3 + G. Some guidelines are derived from the salt-specific constants A, B, D, E, F and G. The heavier isotopes are inclined to be in the more hydrated state in the diluted solution, while the lighter isotopes tend to be in a less hydrated state. In the concentrated solution, heavier isotopes are more likely to be in ion-pair form. Ionic association occurs from the lower concentration in the order of LiI < LiBr < LiCl. The ...

International Nuclear Information System (INIS)

The decay channels of the Ar 2s"-"1 and 2p"-"1 and Kr 3p"-"1 and 3d"-"1 electronic hole states have been investigated by means of photoelectron-photoion coincidence measurements following innershell ionization using synchrotron radiation. With the method of final ion-charge resolving electron spectroscopy it has become possible to disentangle different contributions to the electron spectrum and to determine the decay probabilities P(nl"-"1#->#n+) of the above-mentioned hole states (nl"-"1) to the final ionic charge states n+. A high correlation with threefold or even fourfold charged ions has been found in all cases. Possible decay routes, via cascade or direct double Auger processes, are discussed on the basis of energy-level schemes calculated with the Hartree-Fock method. Special emphasis is laid on the examination of the Kr 3p"-"1 decay process, where the two fine-structure components (j=1/2,3/2) exhibit noticeably different decay probabilities to Kr"3"+ and ...

International Nuclear Information System (INIS)

A novel composite film, comprising of hydrophobic ionic liquid (IL), multi-walled carbon nanotubes (MWNTs) and gold nanoparticles (GNP), was fabricated and characterized. The GNP was introduced through electrochemical deposition on IL-MWNT gel film coated glassy carbon electrodes (GCE). Experiments showed that both IL and MWNTs could facilitate the GNP deposition. With GNP the composite film exhibited smaller electron transfer resistance and higher sensitivity in sensing guanine (G) and adenine (A). Under the optimized experimental conditions, the anodic peak currents were linear to the analyte concentration in the ranges of 0.008-2.0 ?M. The detection limits were down to nanomole level after an accumulation of 150 s on open-circuit. In addition, on the composite film coated GCE, the anodic peaks of G and A were well separated, and their response sensitivities kept almost unchanged no matter whether they coexisted or not. This proposed procedure was successfully ...

International Nuclear Information System (INIS)

The feasibility of immobilizing simulated radioactive slurry (SRS) by alkali-activated slag---clay minerals composite cement (AASCM) was studied under the experimental conditions. The results show that the dosage of SRS and water cement ratio (W/C) have significant effect on the flowability of the mixture of AASCM and SRS. The more dosage of SRS, the lower flowability. When cement/sand ratio is 1: 1 and W/C is 0.45, the flowability of the mixture meets the case of solidification engineering and the compressive strength of the waste forms containing 20% SRS meets the needs of GB 14569.1-93. The setting time of the mixture of AASCM and SRS is highly dependent on temperature while sorts of anions have little influence on it. The application of AASCM is suitable below 20 degree C. The leaching resistance of AASCM based waste forms is superior to that of OPC based waste forms. The control of the forms to Sr2+ is stronger than that to Cs+. Silicon ...

International Nuclear Information System (INIS)

Polymer sealing parts are widely used in various branches of engineering as detachable joints that operate at normal and cryogenic temperatures. They are also used in nuclear-power engineering to seal pumps, pipelines, etc., where they operate at 600-650 K under a neutron fluence of around 10"1"6 cm"-"2 (E #>=# 0.18 MeV) and concomitant #gamma#-irradiation of about 10"6 R. The fluoroplastic-based materials currently used degrade when irradiated in water at 320-360 K with a neutron fluence of 10"1"5 cm"-"2 (thermal neutrons) or 10"1"4 cm"-"2 (fast neutrons), and a concomitant #gamma#-irradiation dose of 2 x 10"6 R. The strength of these fluoroplastics decreases markedly after #gamma#-irradiation (from a cobalt source) at room temperature at doses above 10"6 R. For this reason, flexible and swelling graphites are finding ever increasing application. Graflex foils made of extra-pure natural graphite were found to be radiation-resistant and ...

Energy Technology Data Exchange (ETDEWEB)

The General-Purpose Heat Source (GPHS), an improved radioisotope heat source, employs a unique thermal insulation material, carbon-bonded carbon fiber (CBCF), to protect the fuel capsule and to help achieve the highest possible specific power. The CBCF insulation is made from chopped rayon fiber about 10 ..mu..m in diameter and 250 ..mu..m long, which is carbonized and bonded with phenolic resin particles. The CBCF shapes, both tubes and plates, are formed in a multiple molding facility by vacuum molding a water slurry of the carbonized chopped-rayon fiber (54 wt %) and phenolic resin (46 wt %). The molded shapes are subsequently dried and cured. Final carbonization of the resin is at 1600/sup 0/C. Machining to close tolerances (+-0.08 mm) is accomplished by conventional tooling and fixturing. The resulting material is an excellent lightweight insulation with a nominal density of 0.2 Mg/m/sup 3/ and a thermal conductivity of 0.24 W(m.K) in vacuum at 2000/sup 0/C. ...

Energy Technology Data Exchange (ETDEWEB)

The leached glass is subject to leachant attack and results in surface layer alteration which greatly affects the corrosion progress of glass forms. This work studied the composition change, precipitation, pitting corrosion as well as surface layer break and spallation of the leached glass forms. 6 conclusions can be made: 1. The extent of surface layer alteration is related to many factors such as temperature, pH, leachant chemistry, flow rate and leach duration, etc. 2. The alkali element Na is seriously depleted and the elements like U.Ti,Fe, Ca and Mg are enriched in the surface layer. The influence of media has such order: Fe{sub 2}O{sub 3} > Na-bentonite > Zeolite. 3. The precipitate formed in leach test for 56 days at 90 {infinity}C is mostly amorphous, but after 91 days has crystallized. There is K - Ca - Al - Si crystal,the amount of Al, K and Si is increasing, but the amount of Ca is decreasing along with leaching time. CaCO{sub 3} crystal appeared when leachant ...

Energy Technology Data Exchange (ETDEWEB)

Sol-gel chemistry has a great many potential applications in the preparation of unique electrochemical materials, from non-equilibrium transition metal oxides which may be of use as high energy density electrodes, to high-surface area mixed oxides which may possess high proton conductivity, to novel composite structures consisting of inorganic gels in combination with organic, electronic, and ionic conductors. This paper reviews prior work on proton conduction in gel systems and presents recent work regarding electrode materials prepared by sol-gel methods and inorganic-organic materials.

Energy Technology Data Exchange (ETDEWEB)

Incorporation of TiO{sub 2}, into perfluoroionomer membrane by treatment with TiC1{sub 4}-methanol has been described. Platinum was used as an electrocatalyst. In order to make the system electronically as well as ionically conducting, the electrode was modified with polypyrrole (PPy). Photopolymerisation of pyrrole was accomplished by immersing TiO{sub 2}-Pt-NaF in pyrrole solution. UV-visible and FT-IR Spectroscopic studies were preformed with regards to the formation of the TiO{sub 2}, Pt and PPy within Nafion matrix. We report the construction and evaluation of this integrated system and establish the feasibility of hydrogen generation thereof. (Author)

Energy Technology Data Exchange (ETDEWEB)

The discovery of nearly sixty molecules, often unstable or complexes, in the interstellar space has been one of the greatest surprises of contemporary astronomy. We may, indeed, be surprised that molecules having up to 13 atoms might be synthetized in an extremely diluted space and at a very low temperature. That these molecules are, most of all, organic molecules is another astonishing subject, at least for the non-specialist. The interstellar molecule formation is indeed well understood nowadays, at least for the simplest ones. This article takes stock of interstellar chemistry which is essentially an ionic chemistry very different from laboratory chemistry.

International Nuclear Information System (INIS)

Intraionic spin-orbit--split multiplet levels have been observed by electronic Raman scattering in the intermediate-valence compound EuPd_2Si_2. From the temperature dependence of the Raman peak positions and widths the interconfigurational excitation energy E/sub x/ and an upper limit of the interconfigurational mixing width T/sub f/, respectively, have been obtained. This is the first spectroscopic support for the underlying assumptions of the ionic interconfigurational fluctuation model that has been proposed to describe intermediate valence.

British Library Electronic Table of Contents (United Kingdom)

Using a new simulative technique developed by us, we systematically investigated new ternary or quaternary molten salt systems, which are based on LiF-LiCl, LiF-LiBr, and LiCl-LiBr binary systems, for use as electrolytes in thermal batteries, and evaluated their ionic conductivities and melting points experimentally. It was confirmed experimentally that LiF-LiBr-KF (melting point: 425^oC, ionic conductivity at 500^oC: 2.52Scm^-^1), LiCl-LiBr-KF (405^oC, 2.56Scm^-^1), LiCl-LiBr-NaF-KF (425^oC, 3.11Scm^-^1), LiCl-LiBr-NaCl-KCl (420^oC, 2.73Scm^-^1), and LiCl-LiBr-NaBr-KBr (420^oC, 2.76Scm^-^1) meet our targets for both melting point (350-430^oC) and ionic conductivity (2.0Scm^-^1 and higher at 500^oC). A single cell using the newly developed LiCl-LiBr-NaCl-KCl molten salt as an electrolyte w...

International Nuclear Information System (INIS)

The mixed structure of a nuclear reactor building is composed of SC-columns, S-beams, S-joints and PCa-panels. Following the last report (Part 7)[1], the main test results of the mixed structure, that is, the deformation mode, strain distribution and shear strength, are described. The S-joints using ultrahigh strength materials had no buckling nor shear slipping. The proposed mixed structure resisted the external horizontal forces under integrated uniformity among SC-columns, S-joints and PCa-panels. It could be confirmed that the mixed structure can be established. (author)

British Library Electronic Table of Contents (United Kingdom)

There is proposed the nonlinear model of dose dependence saturation of the yield strength on the base of the vacancy and interstitial barrier interaction in this work. Processes of mutual recombination of vacancy and interstitial barriers and formation of vacancy and interstitial clusters are taken into consideration. In the framework of the model, the analytical equations corresponding to the evolution of the barrier densities and yield strength are obtained. It is shown that the yield strength of irradiated materials decreases with the increasing intensity of barrier recombination processes, the dependence being nonlinear. Also it is shown that the model is valid both for low doses and large doses on the stage of radiation hardening.

CERN Document Server

An accelerator has limited dynamic range: a chain of accelerators is required to reach high energy. A combination of septa and kicker magnets is frequently used to inject and extract beam from each stage. The kicker magnets typically produce rectangular field pulses with fast rise- and/or fall-times, however the field strength is relatively low. To compensate for their relatively low field strength, the kicker magnets are generally combined with electromagnetic septa. The septa provide relatively strong field strength but are either DC or slow pulsed. This paper discusses injection and extraction systems with particular emphasis on the hardware required for the septa.

Energy Technology Data Exchange (ETDEWEB)

The effect of additives on the grafting of a monomer, butylmethacrylate (BA), into simul (a soft wood) has been studied using {sup 60}Co source at 3 Mrad. The enhancement of polymer loading (grafting) by the addition of minute amounts (1%) of oligomers and of polyfunctional monomers into simul + BA system has been further increased in the presence of acid and urea. The synergistic polymer loading yields by acid addition cause substantial decrease of tensile strength values of wood-plastic composite; but urea increases both polymer loading and tensile strength values synergistically in these systems. (author).

International Nuclear Information System (INIS)

The compressive and bending strengths of a local tropical wood (Kapur-Dryobalanop sp.) were improved significantly by suitable impregnation of polymeric monomers (methylmethacrylate, methylmethacrylate - 5% dioxane and vinyl acetate) into the wood cellular structure and subsequent irradiation to form a wood-polymer composite. Statistical analysis revealed a linear relationship between increase in the strengths and the percentage of polymer impregnated. Fractographic analysis of the impact fractured surfaces under the scanning electron microscope showed the nature of the wood-polymer interface, which could account for the increase in the compressive and bending strengths. (author).

Science.gov (United States)

Systems MEMS sensors C11-20 Lifetime Distributions of Aluminum Electrolytic Capacitors C11-22 Adhesion Strength of Advanced Polymer Films for Flexible and Rigid...

Science.gov (United States)

Ultimate Compressive Strength = 3000.0 psi. 3.0 Failure Criteria. The structural criteria used to evaluate the combustor components was chosen ...

Science.gov (United States)

... the Naval Research Laboratory (Contract NOOO14-82-K-2015), Cabot Corporation, and Lord Kinematics Division of Lord Corporation. The authors ...

Science.gov (United States)

Composite Sandwich Panels under Different Thermal Environments, Composite Structures, Vol. 25,. July 1993, pp. 227239. 11. Ko, William L., Mechanical and ...

Science.gov (United States)

Watkins,. Charles. E. : Effect of Aspect. Ratio on the Air ...... Grover,. H. 3. ; Bishop,. S. M. ; and. Jackson,. L. R. : Fatigue. Strengths of Aircraft ...

Energy Technology Data Exchange (ETDEWEB)

Four commercial stainless steels (mat. Nos. 1.4539, 1.4586, 1.4571 and 1.4462) were tested in 96% and 90% sulfuric acid of 80/sup 0/C as to their corrosion fatigue strength by subjecting notched round bars to the rotary bending test. At the same time, the efficiency of anodic protection was examined. With all four steels, the alternating bending strength obtained in the air is essentially reduced. The semiaustenitic steel Nr. 1.4462 shows a lower corrosion fatigue strength than the three austenitic steels. Although making the corrosion fatigue strength of steels better calculable, anodic protection proves insufficient to completely prevent notched round bars from corrosion fatigue in concentrated sulfuric acid.

International Nuclear Information System (INIS)

In the feasibility study on commercialized FBR systems, the application of 12Cr steel, with its physical properties and high-temperature strength properties, as structural material is considered in order to greatly reduce construction costs by compacted instruments and structures. In this report, creep, fatigue and the creep-fatigue properties of Mod.9Cr-1Mo steel forging (thickness 550mm) weld, representing conventional steels, were evaluated in order to obtain the needed basic data for the evaluation of the high-temperature strength of 12Cr steel weld. The results obtained are as follows: (1) Metal suitable for HAZ was made by applying thermal treatment to simulate the thermal hysteresis during welding to clearly define creep and fatigue properties in a HAZ softened zone. (2) Creep strength of the weld metal and the welded joint was equal to that of the base metal. However, the welded joint ruptured in the HAZ softened ...

Science.gov (United States)

hlgh fiber content composites met the minlmum requirements. (1400 O F ) , the hlgher fiber content as-fabricated composites have impact strengths distinctly ...

British Library Electronic Table of Contents (United Kingdom)

An organically modified montmorillonite (MMT) was compounded with polybutylene terephthalate (PBT) in a twin-screw extruder. The organoclay PBT nanocomposites were then injection molded by conventional and microcellular methods. Nitrogen was used as the blowing agent. The effect of organoclay content, organoclay size (8 and 35mm), and speed of the screw (80 and 100rpm) on the mechanical and thermal properties were investigated. The results showed that when the MMT content was 1.0wt.%, the nanocomposites have maximum tensile strength, wear resistance, and cell density. Moreover, the larger the particle size, the greater the tensile strength. The screw speed during compounding also affected the mechanical strength. The higher speed of the screw increased the tensile strength of the nanocompo...

Science.gov (United States)

... kg/m3 density. The Rohacell foam displayed an average ultimate compressive strength of 1546 kPa. The maximum load ...

Science.gov (United States)

... The measured elastic modulus was fairly close to the predicted value, but the ultimate compressive strength (UCS) was quite a bit below the MSC ...

International Nuclear Information System (INIS)

Engineering ceramics have excellent properties such as high strength, high hardness and high heat resistance compared with metallic materials. To apply the ceramic in fast reactor environment, it is necessary to evaluate the sodium compatibility and the influence of sodium on the mechanical properties of ceramics. In this study, the influence of high temperature sodium on the mechanical properties of sintered ceramics of conventional and high purity Al_2O_3, SiC, SiAlON, AlN and unidirectional solidified ceramics of Al_2O_3/YAG eutectic composite were investigated by means of flexure tests. Test specimens were exposed in liquid sodium at 823K and 923K for 3.6Ms. There were no changes in the flexural strength of the conventional and high purity Al_2O_3, AlN and Al_2O_3/YAG eutectic composite after the sodium exposure at 823K. On the contrary, the decrease in the flexural strength was observed in SiC and SiAlON. After the ...

British Library Electronic Table of Contents (United Kingdom)

The majority of research on homeless youth has focused on the multitude of problems faced by this vulnerable population. The current study, while acknowledging the hazards of life on the streets, seeks to explore the personal strengths and informal resources street youth rely on to navigate their environments. Qualitative data from seven focus groups conducted with street youth ages 18?24 were analyzed using content analysis. These data, rich with interactions among youth participants, highlight three important themes: developing ?street smarts,?? existence of personal strengths, and informal resources relied upon by youth to survive. Results provide valuable insights into the strengths of homeless youth that can be useful to providers in assessing street youths? service needs and increasi...

Energy Technology Data Exchange (ETDEWEB)

This dissertation is concerned with the development, experimental diagnostics and mathematical modelling and simulation of polymer electrolyte fuel cells (PEFC). The central themes throughout this thesis are the closely interlinked phenomena of mass and charge transfer. In the face of developing a PEFC system for vehicle propulsion these phenomena are scrutinized on a broad range of relevant scales. Starting from the material related level of the membrane and the gas diffusion layer (GDL) we turn to length scales, where structural features of the cell additionally come into play. These are the scale of flow channels and ribs, the single cell and the cell stack followed by the cell, stack, and system development for an automotive power train. In Chapter 3 selected fundamental material models and properties, respectively, are explored that are crucial for the mathematical modelling and simulation of PEFC, as needed in some succeeding parts of this work. First, established mathematical ...

Energy Technology Data Exchange (ETDEWEB)

Water-resources data for the 1991 water year for Minnesota consist of records of stage, discharge and water quality of streams; stage, contents, and water quality of lakes and reservoirs; and water levels and water quality in wells and springs. The volume contains discharge records for 60 gaging stations; stage and contents for 9 lakes and reservoirs; water quality for 18 stream stations, 1 lake station, 22 partial-record sites, 1 precipitation station, 108 wells; and water levels for 119 observation wells. Also included are 59 high-flow partial-record stations. Additional water data were collected at various sites, not part of the systematic data collection program and are published as miscellaneous measurements or low-flow investigations.

Science.gov (United States)

swimmers in or around the water. Designate a responsible adult who can swim and knows CPR to watch swimmers in or around water. The supervisor should not be involved in any...

International Nuclear Information System (INIS)

The influence of various alloy elements on tensile strength of the eutectic, directionally solidified superalloy 73 C was determined. The tensile properties of the base alloy has been increased by Al, Y and C as alloying elements, while Ni and Ti showed a decreasing effect (alloy softening). However, ductility and thermo-fatigue behaviour had been influenced in a positive way by these elements. The specific meachanism caused by the different elements are discussed. (orig.).

International Nuclear Information System (INIS)

The influence of heat treatment on the structure, mechanical properties and fracture peculiarities of high-strength (#alpha#+#beta#)-titanium alloy VT22 has been studied. It is ascertained that thermal cycling and subsequent high-temperature aging permit to reduce considerably crack growth rate. Thermal cycling is realized in the following mode: heating in #beta#-region, cooling and allowance in (#alpha#+#beta#)-region, heating in #beta#-region.

British Library Electronic Table of Contents (United Kingdom)

Ultrafine grained steels with different carbon contents were produced through warm caliber rolling and evaluated for their stress-strain behavior along with the reduction in area. It was found that the reduction in area-tensile strength balance is far better than the conventional ferrite+pearlite steels and even superior to bainitic steels for all materials tested in the present study.

British Library Electronic Table of Contents (United Kingdom)

A tobermorite/hydroxyapatite composite was prepared by hydrothermal treatment using diatomaceous earth, ?-tricalcium phosphate and slaked lime starting materials. The XRD patterns of the composite confirmed that tobermorite and hydroxyapatite were formed after the hydrothermal process. The bending strength of the composite reached a level higher than 9?MPa after the hydrothermal process. The development of the bending strength was due to the formation of tobermorite and hydroxyapatite during the hydrothermal process. The composite had a high specific surface area due to these newly formed crystals.

Science.gov (United States)

A number of alloys of zirconium have been investigated as part of a program aimed at improving the high-temperature tensile and creep strength of zirconium. These alloys include aluminum, beryllium, lead, magnesium, molybdenum, niobium, tantalum, tin, titanium, tungsten, vanadium, and zinc, binary and ternary alloys. The data indicate that aluminum, lead, molybdenum niobium, tin, titanium, tungsten, and vanadium can be used successfully to harden zirconium, and that aluminum, tin, titanium, and vanadium are particularly effective in maintaining the strength of zirconium at elevated temperatures.

Energy Technology Data Exchange (ETDEWEB)

A method of calculating the neutron source strength in irradiated Fast Flux Test Facility (FFTF), fuel has been developed and is presented in this paper. This method has been used to perform calculations in support of the reactivity monitoring of the FFTF reactor by the modified source multiplication method during refueling operations. 31 refs.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

Triaxial compression tests following stress paths of constant {sigma}{sub 1} were conducted to determine the shear strength of five processed scrap tire products having different gradations and particle shapes. The interparticle frictional component was separated from the total shear strength according to the energy correction concept proposed by researchers. The experimental results show that all five tire chip products have ultimate internal friction angles of 45{degree} to over 60{degree}. The interparticle frictional component of the strength was fully mobilized and nearly reached a constant value after approximately 5% axial strain. The experimental results confirmed that the strength parameter obtained with constant {sigma}{sub 1} was more reasonable. This finding is supported by field observation in which the tire chips have an angle of repose ranging from 37{degree} to 43{degree} (loosely stock ...

Energy Technology Data Exchange (ETDEWEB)

Since the earliest papers on undulaters were published, it has been known how to calculate the spontaneous emission spectrum from ''short'' undulaters when the magnetic field strength parameter is small compared to unity, or in ''single'' frequency sinusoidal undulaters where the magnetic field strength parameter is comparable to or larger than unity, but where the magnetic field amplitude is constant throughout the undulater. Fewer general results have been obtained in the case where the insertion device is both short, i.e., the magnetic field strength parameter changes appreciably throughout the insertion device, and the magnetic field strength is high enough that ponderomotive effects, radiation retardation, and harmonic generation are important physical phenomena. In this paper a general method is presented for calculating the ...

Energy Technology Data Exchange (ETDEWEB)

Experimental discussions were given on effect of V and W addition on the high temperature strength properties of 12% Cr-15% Mn austenite steels. The test samples were added with W at 0% to 3.5% and V at 0% to 0.5% in addition to C and N, and were given aging treatment or solution treatment. This paper describes the following matters on the results of high-temperature strength measurements and structural observation: A remarkable trend was observed that M23 Cb type carbides precipitate in the aging treatment, wherein aging hardening appears prominently which is attributable to ultra-fine deposits of vanadium nitride (VN) in the V-added material; the V addition is very effective in increasing the high-temperature tensile strength and creep fracture strength as compared with single W addition, wherein the said carbides that accelerate the precipitation as a result of the V addition make a large ...

International Nuclear Information System (INIS)

The "2"0 "2"1 "2"2Ne("6Li, d)"2"4 "2"5 "2"6Mg reactions have been studied at a bombarding energy of 32 MeV. Alpha particle spectroscopic strengths have been extracted for several low-lying levels by a finite-range distorted wave analysis. These are compared with theoretical predictions. The agreement is good both for relative strengths to different levels within a nucleus and for ground-state strengths relative to the "1"6O("6Li, d) result. Strengths calculated using eigenfunctions determined in large shell-model computations agree well with pure symmetry SU(3) predictions. The "2"1Ne("6Li, d) angular distributions for transitions to the ground-state band of "2"5Mg are characterized by the lower of the two L-transfers allowed for populating each level. For the 3"+(5.24 MeV) unnatural parity level in "2"4Mg, a two-step calculation gives a better account of the data than does a compound nuclear ...

International Nuclear Information System (INIS)

... Development Center, National Tsing-Hua University, Hsinchu, TW (China)

Energy Technology Data Exchange (ETDEWEB)

An improved process is disclosed for reducing the water content of coal containing bound water by releasing at least a portion of the bound water by maintaining the coal at a temperature from about 220/sup 0/ to about 500/sup 0/ F. in the presence of water at a pressure sufficient to maintain at least portion of the water in a liquid phase for a time sufficient to release at least a portion of the bound water wherein the improvement comprises contacting the coal during such treatment with an active material selected from the group consisting of carboxylic organic acids containing up to about 6 carbon atoms, phenol, phenolic acids and inorganic acids.