The energy recovery by anaerobic purification of wastewaters from olive oil manufactured is reported. The process efficiency is 82%, and the gas (CH4-CO2) yield is 850 L/kg eliminated BOD.
The heavy water reactor such as Wolsung No.1 and No.2 has a purificationsystem to purify the reactor coolant. The control system regulates the coolant temperature to protect the ion exchanger. After the fuel exchanges of operating plant, the increase of the coolant pressure makes the purification temperature control difficult. In this paper, the controllability of the control dynamics of the purificationsystem was analysed and the optimal parameters were proposed. To reduce the effects of the flow disturbance, the feedforward control structure was proposed and analysed.
...Tota-MaharajE-Mail: Interests: water and wastewater treatment, environmental engineering and sustainable systems; sustainable water management; sustainable urban drainage systems (SUDS); combined renewable energy applications with reverse osmosis desalination; microbial fuel cells for bioenergy production and treatment of urban wastewater; solar photocatalytic treatment and disinfection of water/wastewater Dr. Simon Toze CSIRO Land and Water, Queensland Bioscience Precinct - St Lucia, 306 Carmody Road, St Lucia QLD 4067,...
As wastewater travels through a sewer system it undergoes changes in composition. The changes in composition may be caused by chemical, physical and/or biological processes. At present engineers do not take into consideration the impacts of these processes on the wastewater quality when designing wastewater treatment systems. However, the impact of these processes on the chemical oxygen demand, biochemical oxygen demand, nitrogen and phosphorus content of the wastewater can be significant. In the case of the biological processes, microorganisms present in the water as it travels through the sewer system are similar to those found in an activated sludge process. Given that the microorganism population and the hydraulic retention time often resembles that of an activated sludge process, it would seem only reasonable to look further into the ...
...been a world leader in the design, manufacture and installation of high quality precision-engineered systems for water and wastewater treatment fo Create Free Account ...
...been a world leader in the design, manufacture and installation of high quality precision-engineered systems for water and wastewater treatment fo Bulletins Environmental Expert ...
Purge water from a typical wet flue gas desulfurization system contains myriad chemical constituents and heavy metals whose mixture is determined by the fuel source and combustion products as well as the stack gas treatment process. A well-designed water treatment system can tolerate upstream fuel and sorbent arranged in just the right order to produce wastewater acceptable for discharge. This article presents state-of-the-art technologies for treating the waste water that is generated by wet FGD systems. 11 figs., 3 tabs.
TOXCHEM is a microcomputer based modelling system for predicting the fate of toxic contaminants in wastewater treatment plants. The package evaluates concentrations of toxics in final effluent and waste sludge, and mass air emissions from municipal or industrial activated sludge wastewater treatment plants. Maximum allowable influent concentrations of toxics required to meet effluent discharge or air emission limits can also be estimated. The package contains a read-only database with treatability parameters for over 100 contaminants, including organic compounds and metals. If effluent or sludge quality limits have been specified, treatment plant owners and operators can use the package to estimate the permissable discharge limits for dischargers to their collection system. A hypothetical example is provided of application of the software to a planning problem involving the start up of a new operation ...
This publication compiles five documents on volatile organic compounds (VOCs) in wastewater collection systems. The first is a thesis describing experiments conducted to obtain parameters for determining the significance of biodegradation relative to volatilization as a VOC fate mechanism in sewers. The second is a compilation of three papers from the 1992-94 conferences of the Air & Waste Management Association (AWMA). The papers concern VOC emissions at sewer drop structures and an estimation method for determining VOC emissions from industrial sewers. The third is a compilation of two papers from the AWMA 1992 and 1994 conferences, covering the formation of chloroform from household sources. The fourth is a thesis on post-discharge formation of chloroform in untreated municipal wastewater. The final document is a report detailing the derivation of fate mechanism models in the TOXCHEM model.
Water from small scale purification plants is a low cost alternative for consumers in comparison to the bottled commercial presentations. Because of its low cost per liter, the consumption of this product has increased in recent years, stimulating in turn the installation of purificationsystems for these small businesses. The purpose of this study was to estimate the efficiency of small scale purificationsystems located in the cities of Zacatecas and Guadalupe, Zacatecas, to reduce the radioactive content of water. It was measured the total alpha and beta activity in water samples of entry and exit to process, through the liquid scintillation technique. In general it was observed that the process is more efficient in removing alpha that beta activity. The fraction of total alpha activity removed varied between 27 and 100%, while between 0 and 77% of the total beta activity was ...
A novel bioelectrochemical membrane reactor (BEMR), which takes advantage of a membrane bioreactor (MBR) and microbial fuel cells (MFC), is developed for wastewater treatment and energy recovery. In this system, stainless steel mesh with biofilm formed on it serves as both the cathode and the filtration material. Oxygen reduction reactions are effectively catalyzed by the microorganisms attached on the mesh. The effluent turbidity from the BEMR system was low during most of the operation period, and the chemical oxygen demand and NH(4)(+)-N removal efficiencies averaged 92.4% and 95.6%, respectively. With an increase in hydraulic retention time and a decrease in loading rate, the system performance was enhanced. In this BEMR process, a maximum power density of 4.35 W/m(3) and a current density of 18.32 A/m(3) were obtained at a hydraulic retention time of 150 min and external resister of 100 ?. The ...
A permeable reactive mixture has been developed using low cost, readily available materials that is capable of providing effective, long-term phosphorous treatment in areas impacted by on-land wastewater disposal. The reactive mixture creates a geochemical environment suitable for P-attenuation by both adsorption and precipitation reactions. Potential benefits include significant reductions in phosphorous loading to receiving groundwater and surface water systems, and the accumulation of P-mass in a finite and accessible volume of material. The mixture may be applied as a component within surface treatment systems or in subsurface applications such as horizontal or vertical permeable reactive walls. The mixture averaged > 90% treatment efficiency over 3.6 years of continuous-flow laboratory column experiments. The mixture was further evaluated at the pilot-scale to treat municipal wastewater, and the ...
Modec International Inc has selected Siemens Water Technologies to provide sea-water reverse osmosis (SWRO) systems for several floating, production, storage and offloading (FPSO) vessels that are to be operated in deep-water locations. Siemens is also supplying a wastewater reuse system to one of Brazils largest refineries.
The objectives of this study are to make a biosensor on a trial basis which can instantaneously measure the nitrogen in wastewater, and to develop a wastewater treatment system which is capable of on-line measurement and controlling. The system provides easier operational control relating to such a high efficient treatment as the removal of nitrogen content in wastewater, serving as a solution to the eutrophication problem. It can be applied also to the analysis of fertilizer components for agriculture. Ammonia oxidizing bacteria were immobilized with cellulose acetate film, which is mounted on a diaphragm type oxygen electrode to make a sensor, and its responsibility was studied. The gradient is slow in high concentration but sharp in low concentration, and it seems possible to use it for the measurement for less than 20 ppm nitrogen concentration. The dependence of the sensor ...
The potential to scrub biogas in a high rate pond (HRP) was evaluated using apparatus designed to maximize gas-liquid contact. Experiments compared the removal of carbon dioxide from synthetic biogas by an 'in-pond angled gutter' to that by a simulated 'counter-current pit'. Results showed that the counter current pit has potential for use in biogas scrubbing, with synthetic biogas carbon dioxide composition consistently reduced from 40% to<5%. The in-pond angled gutter was less effective due to bubble coalescence which reduced the total bubble surface surface area available for gas transfer. Measurement of oxygen levels in the scrubbed biogas showed that despite supersaturation of oxygen in the HRP water, there was little transfer to the biogas, so that explosive methane/oxygen mixtures would not be formed. Theoretical calculations indicated that the amount of biogas likely to be formed during anaerobic treatment of municipal ...
Odor purification process using bio-function, which is technologically called bio-deodorizing process, utilizes the function of microorganism to convert mal-odor substances to non-odor substances. It attracts attention because the operation cost of a facility is low due to non-use of chemicals and energy, and because it is environmentally friendly without the possibility of generating secondary pollution. It is being used in deodorizing at sewage treatment facilities, fertilizer plants, coating plants, and foundries in Japan, and is more widely used in Europe. The conventional deodorizing technology in Japan mostly focuses on processes of physical chemistry such as activated carbon treatment, chemical scrubbing, combustion, and masking, but bio-deodorizing process tends to replace the conventional processes. This paper explains (1) relation of mal-odor and microorganism, (2) bio-deodorizing system (solid phase system and ...
Palladium/magnetite nanoparticulate catalysts were developed for efficient elimination of halogenated organic pollutants from contaminated wastewater. Particle recovery from treated water can be ensured via magnetic separation. However, in worst-case scenarios, this catalyst removal step might fail, leading to particle release into the environment. Therefore, a toxicological study was conducted to investigate the impact of both pure magnetite and palladium/magnetite nanoparticle exposure upon human skin (HaCaT) and human colon (CaCo-2) cell lines and a cell line from rainbow trout gills (RTgill-W1). To quantify cell viability after particle exposure, three endpoints were examined for all tested cell lines. Additionally, the formation of reactive oxygen species was studied for the human cells. The results showed only minor effects of the particles on the tested cell systems and support the assumption that palladium/magnetite nano-catalysts can ...
Radiometric X-ray fluorescence analysis was used for the determination of Mn, Fe, Cu, Zn and Pb in wastewater and sludges from three wastewater treatment plants in Bratislava (SR). Metals were determined in wastewaters after preconcentration by 8-hydroxyquinoline and in sludges by drying and pressing to pellets. "2"3"8Pu and "1"0"9Cd was used for excitation of fluorescence radiation. (author).
Discussion is presented of world CO{sub 2} emissions and the effect rising population and population distribution has on this. Possible ways of decreasing emissions are presented, including potential for heat recovery, exhaust-air purification as an energy supply, shared power supply in industry, the use of cogeneration, and multiple use of heat in industry. 9 refs., 10 figs., 3 tabs.
The purpose of this study is to extend the knowledge base for wetland treatment to include processes and substances of particular importance to small, on-site systems receiving oil and gas well waste water. Collection of data on the sorption of heavy metals and the degradation of toxic organics is one of the key tasks. The toxic organics phenolics and anthracene, and chromium and copper have been selected as target adsorbates. An information search was performed on oil refinery waste treatment wetland systems.
In a study where the removal of heavy metals from wastewater is the primary aim, the biosorption of heavy metals onto biosolids prepared as Pseudomonas aeruginosa immobilized onto granular activated carbon was investigated in batch and column systems. In the batch system, adsorption equilibriums of heavy metals were reached between 20 and 50 min, and the optimal dosage of biosolids was 0.3 g/L. The biosorption efficiencies were 84, 80, 79, 59 and 42 % for Cr(VI), Ni(II), Cu(II), Zn(II) and Cd(II) ions, respectively. The rate constants of biosorption and pore diffusion of heavy metals were 0.013-0.089 min{sup -1} and 0.026-0.690 min{sup -0.5}. In the column systems, the biosorption efficiencies for all heavy metals increased up to 81-100 %. The affinity of biosorption for various metal ions towards biosolids was decreased in the order: Cr = Ni > Cu > Zn > Cd. (Abstract Copyright ...
The AFGD process as demonstrated by Pure Air at the Bailly Station offers a reliable and cost-effective means of achieving a high degree of SO{sub 2} emissions reduction when burning high-sulfur coals. Many innovative features have been successfully incorporated in this process, and it is ready for widespread commercial use. The system uses a single-loop cocurrent scrubbing process with in-situ oxidation to produce wallboard-grade gypsum instead of wet sludge. A novel wastewater evaporation system minimizes effluents. The advanced scrubbing process uses a common absorber to serve multiple boilers, thereby saving on capital through economies of scale. Major results of the project are: (1) SO{sub 2} removal of over 94 percent was achieved over the three-year demonstration period, with a system availability exceeding 99.5 percent; (2) a large, single absorber handled the combined flue gas of boilers ...
FuelCell Energy in Connecticut has sold 4.5 MW worth of power plants to California renewable energy company BioFuels Fuel Cells, part of New Energy Capital and BioFuels Energy. Three molten carbonate fuel cell power plants - a 2.8 MW DFC3000 unit, a 1.4 MW DFC1500 system, and a 300 kW DFC300 unit - will be installed at three locations in the San Diego area, and utilize purified biogas from the Point Loma wastewater treatment plant as their primary fuel source.
The industrial standard process for the purification of natural gas is to remove acid gases, mainly hydrogen sulfide and carbon dioxide, by the absorption and reaction of these gases with alkanolamines. The natural gas industry requires vapor-liquid equilibrium (VLE) data to develop more energy efficient amine mixtures. Some energy reductions have been realized in the past decade by applying such amine systems as hindered amines, methyldiethanolamine (MDEA), and MDEA based amine mixtures. However, the lack of reliable and accurate VLE data impedes the commercial application of these more efficient alkanolamine systems. The first objective of this project is to improve the accuracy of vapor-liquid equilibrium measurements at low hydrogen sulfide concentrations. The second objective is to make VLE measurements for amine mixtures. By improving the accuracy of the VLE data on MDEA and other amines, energy savings can be ...
The industrial standard process for the purification of natural gas is to remove acid gases, mainly hydrogen sulfide and carbon dioxide, by the absorption and reaction of these gases with alkanolamines. Inadequate data for vapor -- liquid equilibrium (VLE) hinder the industry from converting operations to more energy efficient amine mixtures and conserving energy. Some energy reductions have been realized in the past decade by applying such amine systems as ``hindered`` amines, methyldiethanolamine (MDEA), and MDEA based amine mixtures. However, the lack of reliable and accurate fundamental VLE data impedes the commercial application of these more efficient alkanolamine systems. The first project objective is to improve the accuracy of vapor -- liquid equilibrium measurements at low hydrogen sulfide concentrations. The second project objective is to measure the VLE for amine mixtures. By improving the accuracy of the VLE ...
The industrial standard process for the purification of natural gas is to remove acid gases, mainly hydrogen sulfide and carbon dioxide, by the absorption and reaction of these gases with alkanolamines. Inadequate data for vapor -- liquid equilibrium (VLE) hinder the industry from converting operations to more energy efficient amine mixtures and conserving energy. Some energy reductions have been realized in the past decade by applying such amine systems as hindered'' amines, methyldiethanolamine (MDEA), and MDEA based amine mixtures. However, the lack of reliable and accurate fundamental VLE data impedes the commercial application of these more efficient alkanolamine systems. The first project objective is to improve the accuracy of vapor -- liquid equilibrium measurements at low hydrogen sulfide concentrations. The second project objective is to measure the VLE for amine mixtures. By improving the ...
The purpose of this document is to use existing documentation to review the effectiveness of subsurface flow and surface flow constructed wetlands in treating wastewater and to demonstrate the viability of treating effluent from Savannah River Site outfalls H-02 and H-04 with a subsurface flow constructed wetland to lower copper, lead and zinc concentrations to within National Pollutant Discharge Elimination System (NPDES) Permit limits. Constructed treatment wetlands are engineered systems that have been designed and constructed to use the natural functions of wetlands for wastewater treatment. Constructed wetlands have significantly lower total lifetime costs and often lower capital costs than conventional treatment systems. The two main types of constructed wetlands are surface flow and subsurface flow. In surface flow constructed wetlands, water flows above ground. Subsurface ...
Constructed wetlands may be used for removal of high nutrient loads in greenhouse wastewater prior to discharge into the environment. Temperature affects both the physical and biological activities in wetland systems. Since nitrification and denitrification are temperature-dependent processes, effluent nitrate concentrations will fluctuate due to changes in air and wetland temperature. In a cold climate, constructed wetlands can function in a temperature-controlled, greenhouse environment year-round. This work evaluates four temperature treatments on nitrate removal rates in five planted and five unplanted laboratory-scale wetlands. Wetlands were supplied with a nutrient solution similar to the fertigation runoff solution (100 PPM nitrate-N) used in greenhouse crop production. A first-order kinetic model was used to describe experimental nitrate depletion data and to predict nitrate removal rate constants (k) in the wetlands planted with Iris ...
The merits of single stage absorption heat pumps coupled to simple distillation for effluent treatment are discussed. An experimental integrated absorption heat pump effluent purificationsystem (IAHPEPS) was built and operated with water-lithium bromide as a working mixture. This unit has been used to raise the temperature and hence, the vapour pressure of the impure water contained in one vessel, to the point where pure water vapour will distil from impure effluent solution (tap water or brine) and condense in a second vessel used to collect pure water. Pure effluent production rates of between 0.5 and 4.3 kg h{sup -1} were obtained. The actual coefficient of performance (COP{sub A}) and the heat pump effectiveness varied from 1.1 to 1.4 and 0.58 to 0.72, respectively. The results from the small scale systems indicate the likely results from industrial scale units which could be operated with low quality heat such as ...
Batch and dynamic flow biosorption studies were carried out using the waste biomass entrapped in silica-gel matrix for the removal of nickel(II) ions from synthetic solutions and real wastewater. Batch biosorption conditions were examined with respect to initial pH, S/L ratio, contact time, and initial nickel ion concentration. Zeta potential measurements showed that immobilized biosorbent was negatively charged in the pH range of 3.0-8.0. The immobilized biomass was found to possess relatively high biosorption capacity (98.01 mg g{sup -1}), and biosorption equilibrium was established in a short time of operation (5 min). The equilibrium data were followed by Langmuir, Freundlich, and Dubinin-Radushkevich isotherm models. Scanning electron microscope analysis was used to screen the changes on the surface structure of the waste biomass after immobilization and nickel(II) biosorption. Sorbent-sorbate interactions were confirmed by Fourier transform infrared ...
A full scale co-digestion system for sludge and Olive oil mill effluent (OME) and a regional sludge management plan has been set-up to solve urgent environmental problems, modifying an existing cold municipal digester, by means of simple and effective technology. Monitoring of the full scale system demonstrated good compatibility between OME and sludge, up to 20% mixture, and high removal of organics compounds. Coagulant compounds present in OME (mainly Fats), promoted aggregation and settling of anaerobic sludge and also its acetoclastic activity, minimizing the load returned to the wastewater treatment line and improving also the activated sludge system. The co-digestion of OME with sludge agreed the project purposes, and produced large quantity of biogas and electric energy.
The diffusion coefficient of particles in radioactive gases has been calculated with account of random wandering of aerosols (occurrence of local fields affecting the particles; recoils accompanying radiation emitted by particles, etc.). To determine the diffusion coefficient, the method of Fokker-Planck equation derivation was used. A formula is presented for calculating the radiation-stimulated diffusion coefficient. A linear growth of the diffusion coefficient with radioactivity is noted according to the formula, the diffusion coefficient is mainly determined by the field in the radiation damage region. The aerosol radioactivity may result in a more rapid deposition of aerosols in the pipelines and aerosol purificationsystems. The diffusion rate grows not only in the presence of intrinsic radioactivity but in case of external radiation exposure as well.
We present a simple protocol to purify a coherent-state superposition that has undergone a linear lossy channel. The scheme constitutes only a single beam splitter and a homodyne detector, and thus is experimentally feasible. In practice, a superposition of coherent states is transformed into a classical mixture of coherent states by linear loss, which is usually the dominant decoherence mechanism in optical systems. We also address the possibility of producing a larger amplitude superposition state from decohered states, and show that in most cases the decoherence of the states are amplified along with the amplitude.
Anaerobic processes have been widely used for the treatment of various high-strength industrial wastewaters. However, application has been limited for the treatment of sulfate-rich industrial wastewaters, such as those from the petrochemical, and mining industries. Wastewaters containing benzoate and sulfate were treated in two upflow anaerobic sludge blanket (UASB) reactors at 34--37 C for 320 d. The sulfate concentration was increased stepwise in Reactor-A up to 7,500 mg/L, and was kept mostly constant at 3,000 mg/L in Reactor-B. Both reactors removed over 98% of organic chemical-oxygen demand (COD) for sulfate up to 6,000 mg/L, despite the fact that the mixed liquor contained up to 769 mg S/L of total sulfides and up to 234 mg S/L of dissolved H{sub 2}S. Sulfate0reducing efficiency decreased with the increase in sulfate concentration, but increased with time at each sulfate concentration. Reactor-B consistently reduced ...
This study report presents the shutdown chemistry of PWR primary system to reduce and remove the radioactive corrosion products which were deposited on the nuclear fuel rods surface and the outside of core like steam generator channel head, RCS pipings etc. The major research results are the follows ; the deposition radioactive mechanism of corrosion products, the radiochemical composition, the condition of coolant chemistry to promote the dissolution of radioactive cobalt and nickel ferrite, the control method of dissolved hydrogen concentration in the coolant by the mechanical and chemical methods. The another part of study is to investigate the removal characteristics of corrosion product ions and particles by the demineralization system to suggest the method which the system could be operate effectively in shut-down purification period. (author). 19 refs., 25 figs., 48 tabs.
Radiological and environmental protection experience associated with the reactor cover gas processing system at the Fast Flux Test Facility (FFTF) has been excellent. Personnel radiation exposures received from operating and maintaining the reactor cover gas processing system have been very low, the system has remained free of radioactive particulate contamination through the first seven operating cycles (cesium contamination was detected at the end of Cycle 8A), and releases of radioactivity to the environment have been very low, well below environmental standards. This report discusses these three aspects of fast reactor cover gas purification over the first eight operating cycles of the FFTF (a duration of a little more than four years, from April 1982 through July 1986).
The operation of the Bullhouse Minewater System, used to treat iron-rich minewaters discharged from long-abandoned coal mines, was studied to minimise pollution of the Upper Don river in the UK. Tests were carried out to determine optimal operating conditions. Ochre flocculation with polyacrylamide was efficient in batch tests as the ochre self-flocculated and sedimented in the lagoon without the need for chemical enhancement. The rate of accretion of the pipework in the system was modified by partial dewatering, reshaping and hardening of the deposits during ageing. Samples of ochre recovered from the drying beds and sump deposits were converted to ferric sulphate coagulant by dissolution with sulphuric acid and used with a polyelectrolyte to successfully purify reservoir water and pretreat wastewater. There was considerable local interest in the scheme with educational opportunities for schools and colleges.
Background, aim and scope Treatment performance of constructed wetlands (CWs) is largely dependent on the characteristics of the wastewater. Although livestock wastewater is readily biodegradable in general, its variety in biodegradability can still be significant in practice. In addition, it is a common practice to periodically use disinfectants in livestock activities for health concerns. Obviously, the residual of the disinfectants in livestock wastewater may have serious inhibitory effect on the microbial activities during wastewater treatment. Thus, the main objective of this study was to examine the variety of livestock wastewater in biodegradability and its effect on the performance of a pilot scale tidal flow CWs (TFCWs) in organic matter and nitrogen removal. Furthermore, investig...
... TOXCHEM+ - Wastewater Predictive Fate by Hydromantis Environmental Software Solutions, Inc. TOXCHEM+ is regarded as the most reliable and ... TOXCHEM+ is EPA-approved for estimating ... »Read more » Contact now / Request quote 0 Comments ...
We investigated the effects of wastewater treatment plant (WWTP) discharge on the ecology of bacterial communities in the sediment of a small, low-gradient stream in South Australia. The quantification...Full Text Available
Even the presence of very low concentrations of dyes (1mgL-1) in the effluent is highly visible and is considered aesthetically undesirable. It must be removed from wastewater completely. This study systematically evaluates the performance of adsorption (three kinds of powdered activated carbons), coagulation (AlCl36H2O) and membrane (submerged hollow fiber microfiltration) processes individually in treating two kinds of reactive dyes (Orange 16 and Black 5) and then using a hybrid process with combined coagulation-adsorption-membrane treatment system. Adsorption capacity and kinetics of Orange 16 were much higher and faster than those of Black 5. The dye removal efficiency by coagulation was highly dependent on dye concentration and solution pH. The hybrid process performance was far more...
A novel wastewater treatment technique has been investigated, for reactive dye removal, in batch kinetic systems. These experimental studies have indicated that charred dolomite has the potential to act as an adsorbent for the removal of Brilliant Red reactive dye from aqueous solution. The effect of initial dye concentration, adsorbent mass:liquid volume ratio, and agitation speed on dye removal have been determined with the experimental data mathematically described using empirical external mass transfer and intra-particle diffusion models. The experimental data show conformity with an adsorption process, with the removal rate heavily dependent on both external mass transfer and intra-particle diffusion. PMID:12691893
Examining the relationship between biodiversity and functional stability (resistance and resilience) of activated sludge bacterial communities following disturbance is an important first step towards developing strategies for the design of robust biological wastewater treatment systems. This study investigates the relationship between functional resistance and biodiversity of dominant bacterial taxa by subjecting activated sludge samples, with different levels of biodiversity, to toxic shock loading with cupric sulfate (Cu[II]), 3,5-dichlorophenol (3,5-DCP), or 4-nitrophenol (4-NP). Respirometric batch experiments were performed to determine the functional resistance of activated sludge bacterial community to the three toxicants. Functional resistance was estimated as the 30?min IC50 or th...
Human activities in the karst Ozark Plateaus can impact water quality of springs where surface water is rapidly transferred to subsurface conduits. Bennett Spring, in southern Missouri, is the fourth largest spring in the state and supports local tourism activities. Questions regarding poorly functioning on-site wastewatersystems (OWS) have raised concerns over the long-term water quality of the spring. This study reports the results of a surface water quality monitoring program in the recharge area where monthly samples were collected at base flow to identify potential pollution sources to the spring. Base flow hydrology of the recharge area was highly variable over the study period, which was drier than normal, causing an incomplete sampling record due to no flow conditions at some site...
The goal of this project is to demonstrate that, by combining state-of-the-art technology, highly efficient plant operation and maintenance capabilities and by-product gypsum sales, significant reductions of SO{sub 2} emissions can be achieved at approximately one-half the life cycle cost of a conventional Flue Gas Desulfurization (FGD) system. Further, this emission reduction is achieved without generating solid waste and while minimizing liquid wastewater effluent. Basically, this project entails the design, construction and operation of a nominal 600 MWe AFGD facility to remove SO{sub 2} from coal-fired power plant flue gas at the Northern Indiana Public Service Company`s Bailly Generating Station.
Radionuclide x-ray fluorescence method was used in the determination of Cr, Ni and other heavy metals content in wastewater of an engineering plant taken both before and after chemical treatment. Toxic effects of the wastewaters using Allium cepa root tip cells were tested. (author) 8 refs.; 2 tabs.
Radionuclide X-ray fluorescence method with a Si/Li semiconductor detector and "2"3"8Pu exciting source was used in the determination of Cr, Fe, Ni, Cu, and Zn content in industrial wastewaters. Simultaneously, the effects of the wastewaters on activated sludge biocenose were evaluated. (author) 6 refs.; 1 fig.; 1 tab.
The Fast Flux Test Facility (FFTF) is a 400-megawatt (thermal) sodium-cooled reactor designed for irradiation testing of fuels, materials and components for LMRs. It is operated by the Westinghouse Hanford Company for the US Department of Energy on the government-owned Hanford reservation near Richland, Washington. The first 100-day operating cycle began in April 1982 and the eighth operating cycle was completed in July 1986. Argon is used as the cover gas for all sodium systems at the plant. A program for cover gas monitoring has been in effect since the start of sodium fill in 1978. The argon is supplied to the FFTF by a liquid argon Dewar System and used without further purification.
Two sodium cooled reactors are currently being operated in the United States of America for the US Department of Energy. These are Experimental Breeder Reactor 11, EBR-11, and the Fast Flux Test Facility, FFTF. EBR-11 is located near Idaho Falls, Idaho, and the FFTF is near Richland, Washington. These reactors are currently engaged in a wide range of testing including fuels and materials tests, and plant system performance and safety development. The US DOE program also includes designs of a next generation sodium cooled power reactor. The FFTF and EBR-11 communities are providing input to these designs. This paper discusses the efforts to develop and operate cover gas systems for the sodium cooled nuclear reactor program in the USA.
The coke plant at the Sparrows Point Plant consist of three coke oven batteries and two coal chemical plants. The by-product coke oven gas (COG) consists primarily of hydrogen, methane, carbon monoxide, nitrogen and contaminants consisting of tars, light oils (benzene, toluene, and xylene) hydrogen sulfide, ammonia, water vapor and other hydrocarbons. This raw coke oven gas needs to be cleaned of most of its contaminants before it can be used as a fuel at other operations at the Sparrows Point Plant. In response to environmental concerns, BSC decided to replace much of the existing coke oven gas treatment facilities in the two coal chemical Plants (A and B) with a group of technologies consisting of: Secondary Cooling of the Coke oven Gas; Hydrogen Sulfide Removal; Ammonia Removal; Deacification of Acid Gases Removed; Ammonia Distillation and Destruction; and, Sulfur Recovery. This combination of technologies will replace the existing ammonia removal system, the ...
The coke plant at the Sparrows Point Plant consist of three coke oven batteries and two coal chemical plants. The by-product coke oven gas (COG) consists primarily of hydrogen, methane, carbon monoxide, nitrogen and contaminants consisting of tars, light oils (benzene, toluene, and xylene) hydrogen sulfide, ammonia, water vapor and other hydrocarbons. This raw coke oven gas needs to be cleaned of most of its contaminants before it can be used as a fuel at other operations at the Sparrows Point Plant. In response to environmental concerns, BSC decided to replace much of the existing coke oven gas treatment facilities in the two coal chemical Plants (A and B) with a group of technologies consisting of: Secondary Cooling of the Coke oven Gas; Hydrogen Sulfide Removal; Ammonia Removal; Deacification of Acid Gases Removed; Ammonia Distillation and Destruction; and, Sulfur Recovery. This combination of technologies will replace the existing ammonia removal system, the ...
The purpose of the project is to further develop a Danish natural gas reformer system including optimisation of subsystems and the overall system consisting of a natural gas reformer and fuel cell CHP generator. This will contribute to the evaluation of to what extend Denmark shall develop small reformer units for PEM fuel Cells. In the project a reformer system with a high degree of automatic control has been build that fulfils the CHP requirements to operation time, dynamics etc. This work, with a FP05 reformer unit, has given valuable results concerning the possibilities and limitations of the reformer technology for CHP usage. It is important that the reformer and fuel cell units are designed with matching yields to optimise efficiency, turn-down start-up time etc. The burner that delivers heat for the steam reaction shall be able to use natural gas as fuel. This gives the possibility of using existing burner ...
Among the several chemical processes conducted for the removal of organic matter present in wastewaters coming from some agro-industrial plants (wine distilleries, olive oil mills, etc), the oxidation by ozone has shown a great effectiveness in the destruction of specially refractory pollutants: it is demonstrated that the biodegradability of those wastewaters increases aflcer an ozonation pretreatment. Their great pollutant character is imputed to the presence of some organic compounds, like phenols and polyphenols, which are toxic and inhibit the latter biological treatments. In this research, a competitive kinetic procedure reported by Clurol and Nekouinaini is applied to determine the degradation rate constants by ozone of several phenolic acids which are present in the wastewaters from the olive oil obtaining process. The resulting kinetic expressions for the ozonation reactions are useful for the successful design and ...
Methanol dehydrogenases isolated from bacteria belonging to different classes of methylotrophs contain the same prosthetic group. A procedure for its purification from whole cells is given. The reduced...Full Text Available
We have studied the functions of the intracellular RNAs of mouse mammary tumor virus (MMTV) by purification and translation in vitro. Two major size classes of MMTV RNA, 35S and 24S RNA, were isolated...Full Text Available
An enzyme active against carboxymethyl cellulose (CMC) was purified from the stationary-phase-culture supernatant of Clostridium josui grown in a medium containing ball-milled cellulose. The purification...Full Text Available
A procedure is described for the purification of the enzyme indol-3-ylacetylglucose:myo-inositol indol-3-ylacetyltransferase (IAA-myo-inositol synthase). This enzyme...Full Text Available
AIM: To identify a method for efficient large-scale purification of functional hepatitis B virus polymerase (HBV-Pol) without addition of cellular factors.METHODS: Full-length HBV-Pol (843 amino...Full Text Available
In the electrorefining step of the pyrochemical process, actinide ions dissolved in the LiCl-KCl eutectic salt are recovered as pure actinide metals at a cathode for a re-use as a nuclear fuel from the aspect of its nonproliferation of the nuclear fuel cycles. The lanthanide species dissolved in the LiCl-KCl eutectic salt play an important role in an effective metal purification during the electrorefining step, so it is necessary to understand the chemical and physical behaviors of lanthanides in molten salt. The in situ spectroscopic measurement system and studies according to temperature changes are essential for better understandable information. To our knowledge, the absorption studies of lanthanides at high temperatures have been reported before, but the fluorescence studies of those at high temperature are not reported yet. We will discuss here the fluorescence behaviors of lanthanides in LiCl-KCl molten salt medium according to a ...
In the electrorefining step of the pyrochemical process, actinide ions dissolved in the LiCl-KCl eutectic salt are recovered as pure actinide metals at a cathode for a re-use as a nuclear fuel from the aspect of its nonproliferation of the nuclear fuel cycles. The lanthanide species dissolved in the LiCl-KCl eutectic salt play an important role in an effective metal purification during the electrorefining step, so it is necessary to understand the chemical and physical behaviors of lanthanides in molten salt. The in situ spectroscopic measurement system and studies according to temperature changes are essential for better understandable information. To our knowledge, the absorption studies of lanthanides at high temperatures have been reported before, but the fluorescence studies of those at high temperature are not reported yet. We will discuss here the fluorescence behaviors of lanthanides in LiCl-KCl molten salt medium according to a ...
The harmful effect of phosphate in yellow cake on the TBP purification process and its removal methods are dealed with. The reason of more uranium loss in residue was analyzed. The harmful effect of phosphate on TBP extraction efficiency and operaton of extraction column was discussed. The limit value of uranium concentration in digestion solution was presented. For TBP purification process, the presence of phosphate in yellow cake does more harm than good. (authors)
Tarapur Atomic Power Station Unit-4 is first 540 MWe pressurized heavy water reactor in India. It achieved criticality on 06th March 2005 and then operated at full power i.e 500 MWe. Radiation workers during the normal operation and reactor shutdown are exposed to radiation field. The control of dose rates and the collective dose of the radiation workers is most important for the best performance of the reactor. Experience gained during the operation of the 220 MWe reactors has shown that the Moderator system, primary heat transport system, annulus gas system and moderator cover gas system are the main systems contributing to the dose rate and collective dose. In order to identify the radio nuclides contributing to the radiation field, study was undertaken at TAPS Unit-4. Various samples from the Moderator, primary heat transport system, annulus gas ...
In May 1985, a National Pollutant Discharge Elimination System permit was issued for the Oak Ridge Y-12 Plant, a nuclear weapons components production facility located in Oak Ridge, Tennessee, and operated by Martin Marietta Energy Systems, Inc., for the US Department of Energy. As a condition of the permit, a Biological Monitoring and Abatement Program (BMAP) was developed to demonstrate that the effluent limitations established for the Oak Ridge Y-12 Plant protect the classified uses of the receiving stream (East Fork Poplar Creek), in particular, the growth and propagation of fish and aquatic life, as designated by the Tennessee Department of Health and Environment. A second purpose for the BMAP is to document the ecological effects resulting from implementation of a water pollution control program that will include construction of nine new wastewater treatment facilities over the next 4 years. Because of the complex ...
Research at the interface between biomolecules and inorganic nanocrystals has resulted in a great number of new discoveries. In part this arises from the synergistic duality of the system: biomolecules may act as self-assembly agents for organizing inorganic nanocrystals into functional materials; alternatively, nanocrystals may act as microscopic or spectroscopic labels for elucidating the behavior of complex biomolecular systems. However, success in either of these functions relies heavily uponthe ability to control the conjugation and assembly processes.In the work presented here, we first design a branched DNA scaffold which allows hybridization of DNA-nanocrystal monoconjugates to form discrete assemblies. Importantly, the asymmetry of the branched scaffold allows the formation of asymmetric2assemblies of nanocrystals. In the context of a self-assembled device, this can be considered a step toward the ability to engineer functionally ...
Olive mill effluent (OMW) is an example of a wastewaters containing high concentrations of recalcitrant and toxic compounds which are polyphenolics of different molecular weight. It causes disposal problems because they contain powerful pollutants. Treatment and detoxification of phenolic fraction extracted from olive mill wastewaters as well as a synthetic phenolic mixture was investigated by electro-Fenton method. Results shows that this method is highly efficient in polymerising low molecular mass phenolics and removing a large amount of recalcitrant polyphenolic compounds. This treatment decreased 78% of the toxicity which sustained a good anaerobic post-treatment. (orig.)
Recent molecular characterizations of Cryptosporidium parasites make it possible to differentiate the human-pathogenic Cryptosporidium parasites from those that do...Full Text Available
The kinetics of calcium sulfate crystal growth is of importance in various fields, such as geochemistry, desalination technology, petroleum industry, and water and wastewater treatment. The seeded crystal growth rate of calcium sulfate dihydrate was measured as a function of supersaturation in NaCl electrolyte solutions from 0 to 6 m at temperatures of 25, 50, 70, and 90 C. The growth followed a second-order parabolic rate law with activation energies greater than 53 kJ/mol which suggested the surface reaction as the rate-limiting step. It was observed that the rate constant and the activation energy are solution composition dependent. The rate constant increases with NaCl concentration up to 3 molal and then begins to fall slightly. The activation energy dropped from 61 kJ/mol in the pure Ca-SO[sub 4]H[sub 2]O system to 53 kJ/mol in 3.0 m NaCl solutions. The electrolyte effect was similar to the crystal solubility behavior in aqueous ...
A combination of measuring instruments, consisting of a Beta-Sedimeter and a radionuclide X-ray fluorescence instrument, is described. With the Beta-Sedimeter the C-14-radiation is measured. Through direct irradiation with photons of a Pu238-source in an ancillary irradiation chamber and energy dispersing measurement of the K- and L-radiation resp. of the excited heavy metals with the aid of a Si(Li)-semiconductor detector and a 4-channel analyzer the heavy metal concentrations of the heavy metals Zn, Cr, Ni and Pb are determined. For the determination of cadmium the indirect excitation with Am-241 and Dy-targets is described. The system produces records and operates fully automatically in a step-by-step mode with a testing cycle of 45 minutes. In connection with the process monitoring of the wastewater from a zinc plating plant during a period of 8 months the concentration of the solid material and of the metals Cr and Zn, which were ...
This paper presents a summary of the first phase of the EPA project, which encompasses surveys of residues from industrial sources in Alexandria. Studies to date indicate that wastes from various industries can be recovered economically. Wastes such as tin cans, glass, wastepaper, and food residues from processing of fruits, starch, and beer are examples of reusable industrial wastes in Egypt. The results of experimental studies for reuse of residues from oil refining, starch and yeast processing, and steel pickling are presented. Spent clay from edible oil refining is currently discarded, causing both handling and disposal problems. This clay contains as much as 40% oil; 90% can be recovered by extraction. The recovered oil can be successfully used in soap production, and the spent clay can be reused in oil bleaching. Other examples include starch and yeast wastes, which can be used for animal feed, and spent pickling liquor, which can be used as a coagulant aid for treating paper ...
Atomic Energy of Canada Limited (AECL) operates the Waste Treatment Centre (WTC) to treat and immobilize some of the low- level radioactive waste (LLRW) streams at the Chalk River Laboratories (CRL). The WTC at treats low- level radioactive liquid waste by removing the contaminants from the wastewater, concentrating them, and immobilizing them. The fundamental design concept for the WTC is to process the waste streams using forced circulation type liquid waste evaporation (LWE), to solidify the concentrates using thin film evaporator and to discharge the purified effluent into the Ottawa River following verification monitoring. The solidified product drums are stored in existing storage facilities in the CRL. The LWE was installed in the WTC to treat the LLRW. After about four (4) years of design, construction and cold commissioning, the active commissioning of the evaporator process using radioactive waste streams commenced in February 2000. The LWE has overcome ...
Atomic Energy of Canada Limited (AECL) operates the Waste Treatment Centre (WTC) to treat and immobilize some of the low- level radioactive waste (LLRW) streams at the Chalk River Laboratories (CRL). The WTC at treats low- level radioactive liquid waste by removing the contaminants from the wastewater, concentrating them, and immobilizing them. The fundamental design concept for the WTC is to process the waste streams using forced circulation type liquid waste evaporation (LWE), to solidify the concentrates using thin film evaporator and to discharge the purified effluent into the Ottawa River following verification monitoring. The solidified product drums are stored in existing storage facilities in the CRL. The LWE was installed in the WTC to treat the LLRW. After about four (4) years of design, construction and cold commissioning, the active commissioning of the evaporator process using radioactive waste streams commenced in February 2000. The LWE has overcome ...
The purpose of this study is to develop the radioisotope tracer technology, which can be used in solving industrial and environmental problems and to build a strong tracer group to support the local industries. In relation to the tracer technology in 1999, experiments to estimate the efficiencies of a sludge digester of a waste water treatment plant and a submerged biological reactor of a dye industry were conducted. As a result, the tracer technology for optimization of facilities related to wastewater treatment has been developed and is believed to contribute to improve their operation efficiency. The quantification of the experimental result was attempted to improve the confidence of tracer technology by ECRIN program which basically uses the MCNP simulation principle. Using thin layer activation technique, wear of tappet shim was estimated. Thin layer surface of a tappet shim was irradiated by proton beam and the correlation between the measured activity loss ...
Radionuclide X-ray fluorescence analysis was used for the determination of Cr, Fe, Cu, Zn and Ph in industrial wastewaters (from surface treatment of metals and glasses) after precipitation of determined elements by 8-hydroxyquinoline. (author).
Olive oil mill wastewaters (OMW) cause disposal problems because they contain powerful pollutants such as phenolic compounds. Complete biodegradation or removal of these compounds is hardly achieved by a single treatment method. In this work, we investigated 2 integrated technologies for the treatment of the recalcitrant contaminants of OMW, allowing water recovery and reuse for agricultural purposes. (Author)
... Biodegradable plastics have the potential to be used in various flushable sanitary product applications such as sanitary towels, colostomy bags and other absorbent products. In addition, effluent from recycling activities must be treated in wastewater treatment plants and may contain biodegradable plastics. Flushable biodegradable plastics can have an adverse impact on wastewater treatment plants due to the very fast throughputs, typically 4 to 8 hours, from the drain to the plant. This length of time is insufficient for many biodegradable plastics to lose their structure. Such plastics can ...
Contents of this report are under the following topical sections: Legal Authority; Summary and Scope; Data Collection Activities; Industry Description; Industry Subcategorization; Water Use and Wastewater Characterization; Pollutants Selected for Regulation; Pollution Prevention and Wastewater Treatment Technologies; Development of Control and Treatment Options; Costs of Technology Bases for Regulations; Pollutant Reduction Estimates; Non-Water Quality Impacts; Implementation of Proposed Effluent Limitation Guidelines and Standards; Analytical Methods; and Glossary.
Borrelia burgdorferi sensu lato genospecies were differentiated by PCR-based sequencing of the borrelial flagellin gene. To evaluate the usefulness of KingFisher"T"M magnetic particle processor in PCR product purification, borrelia PCR products were purified with KingFisher"T"M magnetic particle processor prior to cycle sequencing and the quality of the sequence data received was analyzed. KingFisher was found to offer a rapid and reliable alternative for borrelial PCR product purification.
An anaerobic fermenter-decanter for the purification of residual water from the sugar industry, with recovery of methane, consists of a tank with inclined walls, with a central agitator on a vertical shaft. A flexible cover anchored by its periphery to the walls of the tank and totally submerged forms a collecting pocket for the fermentation gases. The water to be purified is introduced, after being heated to about 35, towards the bottom of the tank near the agitator. A metal collecting bell with submerged edges and with the shaft of the agitator passing axially through it is connected by its edges to a central opening of the cover. The purification yields may exceed 90%.
A rapid and highly reproducible chromatographic technique has been developed for analysis and purification of complex mixtures of oligoribonucleotides. The method utilizes a column of microparticulate...Full Text Available
Total anthocyanins in different cultivars of mulberry were measured and a process for the industrial preparation of mulberry anthocyanins as a natural food colorant was studied. In 31 cultivars of mulberry,...Full Text Available
The non-blast furnace coke produced in the shaft ovens of the Angarsk Semi-coking Plant is used principally in gas generator ovens and partially as a carbonaceous reducing agent in the ferroalloy process. The sulfur content of this coke is not limited by the standards documents, but it is significant, especially in the production of process gases. In a number of recent years the sulfur removal system of the gasification divisions have been experiencing difficulties, not achieving the assigned gas purification parameters, with a resulting H/sub 2/S concentration in the purified gas of 300-700 mg/m/sup 3/ as compared to the standard of 50. Realizing that in the gasification practically all the organic matter of the coke, including the sulfur, enters the gas, the impairment in the quality of the sulfur removal is related to the increase in the sulfur content of the coke. Thus, an analysis of the results was conducted for the determination of the ...
The Plutonium Finishing Plant (PFP) previously known as the Plutonium Process and Storage Facility, or Z-Plant, was built and put into operation in 1949. Since 1949 PFP has been used for various processing missions, including plutonium purification, oxide production, metal production, parts fabrication, plutonium recovery, and the recovery of americium (Am-241). The PFP has also been used for receipt and large scale storage of plutonium scrap and product materials. The PFP Final Safety Analysis Report (FSAR) was prepared by WHC to document the hazards associated with the facility, present safety analyses of potential accident scenarios, and demonstrate the adequacy of safety class structures, systems, and components (SSCs) and operational safety requirements (OSRs) necessary to eliminate, control, or mitigate the identified hazards. Documented in this Safety Evaluation Report (SER) is DOE`s independent review and evaluation of the PFP FSAR and ...
A large amount of industrial water is used for cooling the various process fluids in the petroleum purification factories as well as petroleum chemistry factories. Consequently, a lot of heat exchangers as the necessary constitutional instruments are made of carbon steel. Due to the most of the corrosions of the carbon steel occurring in such cooling water systems are pitting corrosions, the inhibition thereof is extremely important for the elongation of the life of the plants and the stable operation. In this paper, the influences of water quality fractions on pitting corrosion of carbon steel in cooling water circumstance are examined aiming at the fouling in the cooling water. The fouling in the cooling water does not only increase the amount of occurrence of pitting corrosion but also accelerates the progress of pitting corrosion enlarging the rust due to its deposition near the anode. Since only the inhibitor is not sufficient to inhibit ...
Recent nuclear power plants require high purity water to protect nuclear reactors or steam generators from SCC and maintain in good condition. In this connection, it is especially important to minimize sulfate, which is a corrosive chemical originated from oxidative degradation of cation exchange resins during operation. Recently, uniform particle size (UPS) strong acid cation gel resin with 14% cross-linkage, which has excellent stability against oxidization, has been applied to several condensate purificationsystems. For further improvement of water quality, some methods for changing the configuration of condensate demineralizer's resin bed have been examined. For example, these methods correspond to anion under layer and cation over layer. We have tested these methods by cold column tests. Furthermore, we have developed the newly anion exchange resin having higher efficiency and capacity for absorbing leachables from cation exchange resins. ...
An evaporator using a hydrophobic membrane made from a polytetrafluoroethylene (PTFE) was developed to improve DF (Decontamination Factor) and to reduce evaporator size. The membrane distillation, provided by the evaporator, is a new technique for liquid purification. Fundamental experiments were carried out to develop the membrane filter (tube type, outer diameter, 8 mm; membrane thickness, 500 {mu}m) for radioactive liquid treatment. The continuous operation test using actual liquid waste was also made during about 3,000 h. (This is almost equal to the operation time of an actual evaporator per year.) The evaporation rate decreased with increase an operation time due to contamination of waste impurity. But the rate was recovered by washing the membrane with hot water and then drying it. DF was over 10{sup 4} which is ten times larger than that for a conventional system. A pilot plant (capacity, 200 kg-liquid waste/h) was constructed and its ...
Chemical-looping combustion (CLC), has previously been studied as a method for separating CO{sub 2} during combustion of gaseous fuels. In this project the possibility to apply this process for direct use of solid fuels has been investigated. The following has been accomplished: A 10 kW reactor system for CLC with solid fuels has been designed and built. Tests with solid fuel and metal oxid particles in a laboratory reactor show that it is possible to oxidize solid fuels with metal oxide particles in cyclic testing, thus giving proof of basic concept. They also show how the reaction rate is affected by temperature, steam concentration etc., and, most important of all, that the rates of reaction are realistic. Tests with metal oxide materials available at low costs have been successful. Chemical-looping combustion with solid fuels has a potential to achieve very low costs for separation of CO{sub 2}, below 10 Euro/ton CO{sub 2}. In summary the studies of metal ...
The investigations showed that the new adsorber/catalyst composites are well suited for chemical degradation of persistent water pollutants. Compared with alternative processes, the reaction selectivity and the consumption of oxidant are more favourable as the reaction now takes place on/inside the solid. The process, which was developed originally for purification of contaminated water, can be transferred to many other systems of materials. For example, it is expected that the soot emissions of diesel engines will be reduced significantly after efficient hydrogenation of the aromatics contained in the diesel engine on molybdenum-charged mesoporous composites. [German] Mit den vorliegenden Untersuchungen konnte ein erster Nachweis gefuehrt werden, dass die neu entwickelten Adsorber/Katalysator-Komposite fuer den chemischen Abbau persistenter Wasserschadstoffe geeignet sind. Im Vergleich zu alternativen Verfahrensloesungen kann die Selektivitaet ...
This paper explores the potential of combining substance-flow modelling with water and wastewater sampling to trace consumption-related substances emitted through the urban wastewater. The method is exemplified on sucralose. Sucralose is a chemical sweetener that is 600 times sweeter than sucrose and has been on the European market since 2004. As a food additive, sucralose has recently increased in usage in a number of foods, such as soft drinks, dairy products, candy and several dietary products. In a field campaign, sucralose concentrations were measured in the inflow and outflow of the local wastewater treatment plant in Linkoping, Sweden, as well as upstream and downstream of the receiving stream and in Lake Roxen. This allows the loads emitted from the city to be estimated. A method c...
In this study, the use of the weakly basic anion exchange resins of phenol-formaldehyde (Amberlyst A 23), polyacrylate (Amberlite IRA 67) and polystyrene (Lewatit MonoPlus MP 62) matrices for removal of the reactive dye Remazol Black B (RBB) from aqueous solution and wastewater were investigated. RBB sorption on the anion exchangers was a time dependent process. Color reduction percentiles of 75.2, 33.9 and 25.1% in wastewater treatment were found after 216 h of phase contact time with Lewatit MonoPlus MP 62, Amberlyst A 23 and Amberlite IRA 67, respectively. Inorganic salts and anionic surfactant action influenced RBB uptake by the anion exchangers. The amounts of dye retained by the anion exchangers increased with a rise in temperature. The maximum sorption capacities calculated from the...
Air toxics from the industrial wastewater treatment plants (IWTPs) impose serious health concerns on its surrounding residential neighborhoods. To address such health concerns, one of the key challenges is to quantify the air emissions from the IWTPs. The objective here is to characterize the air emissions from the IWTPs and quantify its associated uncertainty. An IWTP receiving the wastewaters from an airplane maintenance facility is used for illustration with focus on the quantification of air emissions for benzyl alcohol, phenol, methylene chloride, 2-butanone, and acetone. Two general fate models, i.e., WATER9 and TOXCHEM+V3.0 were used to model the IWTP and quantify the air emissions. Monte Carlo and Bootstrap simulation were used for uncertainty analysis. On average, air emissions fr...
Reclaimed Energy Company, Inc., Connersville, IN, receives waste generated from a wide variety of industrial applications which include paint, printing and degreasing companies. The wastes are stored in separate tanks and then distilled in batches (pot distillation). The recovered solvents can be returned to the originator. The residue, left after the solvents are distilled, is disposed of using an environmentally safe, economical procedure. The company worked with an engineering and fabrication firm to develop a continuous processing system that employs a mechanically agitated thin-film evaporator to distill the solvents. Successful performance of the evaporator was ensured by processing samples of solvents through the evaporator manufacturer's pilot plant facilities before the full-sized system was designed. Reclaimed Energy Company, Inc., has realized a number of advantages by going from pot distillation to the agitated thin-film ...
Anaerobic treatment of a volatile fatty acid (VFA) mixture was investigated under psychrophilic (3 to 8°C) conditions in two laboratory-scale expanded granular sludge bed reactor stages in series....Full Text Available
Wet-weather flow (WWF), including combined-sewer overflow (CSO, sanitary-sewer overflow, and stormwater (SW), is a significant contributor of microbial contamination to surface water and ground water. By using effective wastewater or SW disinfection, introduction of pathogen con...
The possibility of oxidizing at a PbO{sub 2} anode the phenols and polyphenols, present in the olive oil mill wastewater, has been studied as a pre-treatment for the submission of such wastewater to the traditional biological treatments. The results obtained operating at current densities ranging 500 to 2000 A/m{sup 2} show that it is possible to reduce the concentration of the phenolic components, which interfere with the biological treatments, down to low values without decreasing too much the total organic content of the wastewater. [Italian] E' stata studiata la possibilita' di ossidare anodicamente i componenti fenolici delle acque reflue di frantoio, quale pretrattamento delle stesse prima del loro invio ai processi di trattamento biologico. I risultati ottenuti impiegando PbO{sub 2} quale materiale anodico e operando con densita' di corrente comprese tra 500 e 2000 A/m{sup 2} mostrano come ...
Background and AimsPlants from the family Lemnaceae are widely used in ecological engineering projects to purify wastewater and eutrophic water bodies. However, the biology of nutrient...Full Text Available
The pattern of biodegradation and the chemical changes occurring in the macromolecular fraction of domestic sludge during autothermal thermophilic aerobic digestion (ATAD) was monitored and characterised...Full Text Available
Addition of Gadolinium Nitrate as chemical shim to moderator heavy water of 540 MWe PHWR, at 15 mg/kg level (at a pH of 5.0) is practiced for reactor shutdown purposes. Presently a strong acid cation exchanger column is used for this purpose. During this operation, the moderator pH of 3.8, with the IX column outlet pH of ?3.5-3.6 was observed against the technical specification demand that when Gd is present, the pH of moderator must be in the range of 5.0-5.5. In order to achieve an iso-pH regime during Gd removal, studies were conducted using a mixed bed of strong acid cation resin plus a weak base anion resin (loaded in the volume ratio of 1 : 6), backed up in the same column (bottom most layer) by a 5 % nitric acid loaded weak base resin and topped by a strong acid cation resin (uppermost layer) simulating system flow velocity and percentage loading of resin. Using such a column it is demonstrated that Gd removal could be achieved simultaneously maintaining the ...
SummaryInitial results from the use of activated dolomite from QUESTOR project L1 have proved extremely encouraging in terms of metallic ion (also phosphate, nitrate and dye) removal from wastewater, with capacities in some instances in excess of commercially available activated carbons.This new project involves investigating actual plant effluent in laboratory scale columns and the design of a pilot scale rig for on site trials. The project also involves investigating disposal options and an economic [continued...
Olive tree (Olea european L.) cultivation, the major tree crops in Mediterranean countries is being extended to irrigated lands. However, the limited water availability, the severe climatic conditions and the increased need for good water quality for urban and industrial sector uses are leading to the urgent use of less water qualities (brackish water and recycled wastewater) for olive tree irrigation. The aim of this work was to asses the effects of long term irrigation with treated waste water (TWW) on the soil chemical properties, on olive tree growth and on oil quality characteristics. (Author)
Magnetic separation of several classes of antibiotics was investigated using electrochemical magnetic seeding. Electrocoagulation with a sacrificial anode followed by addition of magnetite particles was applied for the magnetic seeding of antibiotics. With electrochemical magnetic seeding using an iron anode, tetracycline antibiotics (oxytetracycline, chlortetracycline, doxycycline and tetracycline) and cephalosporin antibiotic (cefdinir) were rapidly removed from synthetic wastewater by magnetic separation using a neodymium magnet. Iron and aluminium anodes were suitable for magnetic seeding of the antibiotics. The results indicated that the ability of antibiotics to form strong complex with iron and aluminium allowed the higher removal by magnetic separation. This method would be appropriate for rapid treatment of antibiotics in wastewater.
Biomass can provide a substantial energy source. Liquids are preferred for use as transportation fuels because of their high energy density and handling ease and safety. Liquid fuel production from biomass can be accomplished by any of several different processes including hydrolysis and fermentation of the carbohydrates to alcohol fuels, thermal gasification and synthesis of alcohol or hydrocarbon fuels, direct extraction of biologically produced hydrocarbons such as seed oils or algae lipids, or direct thermochemical conversion of the biomass to liquids and catalytic upgrading to hydrocarbon fuels. This report discusses direct thermochemical conversion to achieve biomass liquefaction and the requirements for wastewater treatment inherent in such processing. 21 refs.
This paper presents a mathematical model to analyze the solar evaporation in a shallow pond in steady state, when the inlet flow rate, concentration, surface area and solar radiation are given. The simultaneous heat and mass transfer mechanisms are considered for quantifying the amount of evaporated water to the atmosphere and the actual absorbed heat by wastewater is calculated to obtain the bottom temperature of water pond. The heat losses to air by radiation and convection mechanisms are considered and the heat transmission across the water film is evaluated by the forced convection mechanism. 6 refs., 5 figs., 1 tab.
Purification parameters of the vacuum distillation process for AM50A and AZ31B magnesium alloy were studied. The vacuum distillation tests were kept at 580 C to 620 C up to 10 h under a vacuum pressure of about 1 Pa. The purification ratio for AM50A magnesium alloy increases with increasing the purification time. The chemical compositions of materials deposited purifying at 580 C for AM50A magnesium alloy almost satisfy the values for pure magnesium specified by JIS standard specification. The chemical compositions of deposited materials at 600 C for AZ31B magnesium alloy satisfy the values specified by the standard specification except for Zn. (orig.)
Gadolinium nitrate has been employed in Indian nuclear reactors for the first time as soluble neutron poison in the heavy water moderators of the 540 MWe PHWRs TAPS 3 and 4, as a fast acting secondary shut down system (SDS-2); and also for reactivity shim. For this purpose, the moderator purificationsystem is currently equipped with special ion-exchange columns/schemes, developed by present authors. However, for gadolinium removal from moderator in the post SDS-2 scenario, the two stage ion-exchange - cation bed operation followed by mixed bed operation - results in low pH conditions persisting in the moderator for a few hours, which gives rise to certain operational problems. The present paper describes a mixed bed ion-exchange scheme employing macro-porous strong acid cation and macro-porous weak base anion resins, which has been developed to eliminate acidic conditions and gives a better pH control. The cation to anion ...
Valdez, Alaska achieved worldwide attention with the Exxon Valdez oil spill. This exacerbated an already polarized situation (industry, government, citizens, environmental groups) regarding the Valdez Terminal of the Trans Alaska Pipeline System. Other than spills, the major focus of environmental concern was and remains the Terminal`s Ballast Water Treatment Plant (BWTP) which discharges into Port Valdez. The previous NPDES wastewater discharge permits for this facility have been contentious for almost the entire period of pipeline operation. The draft NPDES permit is scheduled to be proposed for reissuance this year. However, a significant change has been initiated which so far is resulting in cooperation rather than confrontation between the various primary stakeholders. This presentation will explain how this change was initiated, how it is being maintained, and how what is happening could be a model for progress through cooperation. ...
The industrial application of anaerobic digestion is a relatively new, yet proven waste treatment technology. Anaerobic digestion reduces and upgrades organic waste, and is a good way to control air pollution as it reduces methane and nitrous gas emissions. For environmental and energy considerations, anaerobic digestion is a nearly perfect waste treatment process. However, its economic viability is still in question. A number of parameters - type of waste (solid or liquid), digester system, facility size, product quality and end use, environmental requirements, cost of alternative treatments (including labor), and interest rates - define the investment and operating costs of an anaerobic digestion facility. Therefore, identical facilities that treat the same amount and type of waste may, depending on location, legislation, and end product characteristics, reveal radically different costs. A good approach for evaluating the economics of anaerobic digestion is to ...
Acidic constituents in crude oil are associated with the formation of stable emulsions during production and present a challenge for efficient oil recovery and processing. Acid molecules, including naphthenic acids and acidic sulfur in crude oil cause corrosion in refineries and pipelines. Naphthenic acids are also significant because of their surface activity and marginal water solubility, so that they may leach to wastewaters and cause adverse environmental effects. Acidic components of oil are not limited to carboxylic acids but also molecules that contain sulfur and nitrogen. As such, an improved understanding of the chemistry and physics of petroleum at the molecular level is needed in order to understand the range of problems associated with acidic oil components and to design better solutions. The applications of negative-ion electrospray ionization (ESI) Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) for speciation of acidic oil ...
N alpha-Acetylenkephalin carboxypeptidase was co-purified with N-acetyltyrosine deacetylase from monkey kidney. Almost 90% of the activity from the homogenate was recovered in a high-speed supernatant...Full Text Available
We have synthesized a novel stable precursor, saligenin phosphorotrichloridate, which, on reaction with N-monobiotinyldiamines, generates a series of biotinylated covalent inhibitors of serine esterases....Full Text Available
Amorphous silicates having small particles with a large surface area were found to have high nonspecific adsorption capacity. Investigations with Escherichia coli T4 bacteriophage have...Full Text Available
The chloroplast and cytoplasmic isoenzymes of phosphoglycerate kinase (PGK) (EC. 2.7.2.3) from Hordeum vulgare leaves have been separated and purified for the first time to apparent...Full Text Available
Carbon nanotubes (CNTs) are considered one of the most promising materials in nanotechnology, with attractive properties for many technologic applications. The different synthesis, purification, and...Full Text Available
Phospho-beta-galactosidase (P-beta-gal), the enzyme which catalyzes the first step in the metabolism of intracellular lactose phosphate, occurred at high specific activity in the cytoplasm in 12 of...Full Text Available
The characterization of the single-chain protein in Chinese-cobra (Naja naja atra) blood serum, which yields strong specific protection against the venom of the same snake, is reported. The protein,...Full Text Available
mRNA guanylyltransferase has been extensively purified from calf thymus. A GTP-binding assay was used based on the observations by Shuman and Hurwitz (1981) and Venkatesan and Moss (1982) that vaccinia...Full Text Available
BackgroundBaculovirus, which has a width of 40 nm and a length of 250-300 nm, can display functional peptides, receptors and antigens on its surface by their fusion with a baculovirus...Full Text Available
1. The penicillinases formed by penicillinase-constitutive mutant strains from two closely related varieties (749 and 6346) of Bacillus licheniformis have been isolated, characterized...Full Text Available
Extracts of Chlorella pyrenoidosa, Euglena gracilis var. bacillaris, spinach, barley, Dictyostelium discoideum and Escherichia coli...Full Text Available
We recently found that many RNA polymerase II transcription factors are modified with N-acetylglucosamine residues. These sugar moieties confer upon transcription factors an ability to bind the lectin wheat germ agglutinin. We have taken advantage of this interaction to devise a purification procedure for the "GC-box" binding transcription factor Sp1. Crude nuclear extracts are first subjected to wheat germ agglutinin affinity chromatography and then subjected to sequence-specific DNA affinity chromatography. The Sp1 protein purified by this procedure is at least 95% pure, and the overall recovery is greater than 80%. In addition to yielding larger quantities of Sp1 than conventional schemes, the new purification procedure is also simpler and more rapid. We show that wheat germ agglutinin affinity chromatography can also be used to purify the glycosylated forms of the CCAAT-binding transcription factor. Thus, wheat germ agglutinin affinity ...
In Chlamydomonas reinhardtii y-1, newly synthesized chlorophyll a/b-binding apoproteins are degraded when chlorophylls are not present for assembly of stable light-harvesting...Full Text Available
A Monascus pilosus strain was selected for production of intracellular α-galactosidase. Optimum conditions for mycelial growth and enzyme induction were determined. Galactose...Full Text Available
A cholinesterase was partially purified from bush bean (Phaseolus vulgaris L.) roots by using acridinium-based ligand affinity chromatography. The procedure gave a 78-fold increase in specific activity,...Full Text Available
The clotting activity of Staphylococcus aureus strain 104 was purified 46,000-fold, but absolute purity was not achieved. Carbohydrate content of the purified material was not more than 5%. Elution...Full Text Available
An enriched glucan synthase fraction was obtained from red beet root microsomes by sequential extraction with the detergents 3-[(3-cholamidopropyl)dimethylammonio]-1-propanesulfonate and digitonin....Full Text Available
Organisms in the genus Mycobacterium cause a variety of human diseases. One member of the genus, M. ulcerans, causes a necrotizing skin disease called Buruli ulcer....Full Text Available
Aminopeptidase II, one of the two major aminopeptidases in the giant alga Chara australis, was partially purified. Its molecular weight was estimated to be about 80,000 by gel permeation...Full Text Available
Basal segments taken from Old Home and Bartlett pear hardwood cuttings collected at intervals during the rooting period in September were extracted with ethanol and fractionated by paper chromatography...Full Text Available
The identification of host cell factors for virus replication holds great promise for the development of new anti-viral therapies. Recently, high-throughput screening methods have emerged as...Full Text Available
Glandular trichomes of the wild tomato species Lycopersicon pennellii secrete 2,3,4-O-tri-acyl-glucose (-Glc), which contributes to insect resistance. A Glc acyltransferase...Full Text Available
The various steps of gas treatment in the Sasol II coal liquefaction plant are discussed: CO/sub 2/ removal, separation of the hydrocarbon fractions and the recirculated hydrogen by low-temperature decomposition, production of pure hydrogen by alternating pressure absorption.
The functional and thermodynamic characteristics of the ubiquinolcytochrome (Cyt) c oxidoreductase in a Cyt b/c1-enriched fraction (defined...Full Text Available
The notes describe in detail primary and secondary galvanic cells, fuel cells, electrochemical synthesis and electroplating processes, corrosion: measurments, inhibitors, cathodic and anodic protection, details of metal dissolution reactions, Pourbaix diagrams and purification of waste water from galvanic industries.
Biodiesel is derived from triacylglycerides and is produced primarily through transesterification, a chemical reaction of vegetable oils with alcohol, methanol or ethanol. The cost of raw material should be considered since 85 per cent of production cost is related to vegetable oil. The purpose of this study was to evaluate oil expression of sunflower seed. It also examined the sunflower crude oil as a raw material for biodiesel by transesterification in both laboratory and pilot scale studies. Three different biodiesel purification methods were examined. The best result for oil expelling (68.4 per cent) at the experimental stage was obtained for seeds with a moisture content of 6.9 per cent at 25 degrees C and at a screw speed of 114 rpm. For biodiesel production at the laboratory scale, the best result for oil expelling was 87.5 per cent. It was obtained with an ethanol:oil molar ratio of 4.7:1 and with a 4.42 per cent catalyst concentration related to the ...
Hundreds of genomes have been successfully sequenced to date, and the data are publicly available. At the same time, the advances in large-scale expression and purification of recombinant proteins have...Full Text Available
Teleost gut associated lymphoid tissue (GALT) consists of leucocyte populations located both intraepithelially and in the lamina propria with no structural organization. The present study aims to assess...Full Text Available
We describe a method for affinity purification of sequence-specific DNA binding proteins that is fast and effective. Complementary chemically synthesized oligodeoxynucleotides that contain a recognition site for a sequence-specific DNA binding protein are annealed and ligated to give oligomers. This DNA is then covalently coupled to Sepharose CL-2B with cyanogen bromide to yield the affinity resin. A partially purified protein fraction is combined with competitor DNA and subsequently passed through the DNA-Sepharose resin. The desired sequence-specific DNA binding protein is purified because it preferentially binds to the recognition sites in the affinity resin rather than to the nonspecific competitor DNA in solution. For example, a protein fraction that is enriched for transcription factor Sp1 can be further purified 500- to 1000-fold by two sequential affinity chromatography steps to give Sp1 of an estimated 90% homogeneity with 30% yield. In addition, the use ...
MOX fuel for FBR is allowed to contain impurities within several thousand ppm, which means less than 1000 of decontamination factor (DF) in reprocessing is enough for Pu and U recycle use. The Advanced Fuel Recycle proposed by PNC is on this basis. The concept consists of innovations on both MOX fuel fabrication and aqueous reprocessing technologies based on the Purex process and it is believed that successful optimization of fuel cycle interface condition is the key issue to realize the concept. The lower DF such as 1000 can be easily obtained by the simplified Purex flowsheet which has no purification steps. However, new subject arises in MOX fuel fabrication, that is, fabrication is conducted in the shielding cell using equipment which is maintained remotely. A simplified fabrication technology becomes essential to establish the remote maintenance system and is one of the critical path for achieving the Advanced Fuel Recycle. The PNC`s ...
We prove that the 1984 protocol of Bennett and Brassard (BB84) for quantum key distribution is secure. We first give a key distribution protocol based on entanglement purification, which can be proven secure using methods from Lo and Chau's proof of security for a similar protocol. We then show that the security of this protocol implies the security of BB84. The entanglement purification based protocol uses Calderbank-Shor-Steane codes, and properties of these codes are used to remove the use of quantum computation from the Lo-Chau protocol. (c) 2000 The American Physical Society.
A simple and rapid procedure was developed for the purification of cyclotron-produced {sup 203}Pb via the {sup 203}Tl(d,2n) {sup 203}Pb reaction. A Pb(II) selective ion-exchange resin, with commercial name Pb Resin from Eichrom Technologies, Inc., was used to purify {sup 203}Pb from the cyclotron-irradiated Tl target with excellent recovery of the enriched Tl target material. The purified {sup 203}Pb was used to radiolabel the monoclonal antibody Herceptin. The in vitro and in vivo properties of the {sup 203}Pb radioimmunoconjugate were evaluated.
Methods and apparatus are described for efficient photodetachment and purification of negative ion beams. A method of purifying an ion beam includes: inputting the ion beam into a gas-filled multipole ion guide, the ion beam including a plurality of ions; increasing a laser-ion interaction time by collisional cooling the plurality of ions using the gas-filled multipole ion guide, the plurality of ions including at least one contaminant; and suppressing the at least one contaminant by selectively removing the at least one contaminant from the ion beam by electron photodetaching at least a portion of the at least one contaminant using a laser beam.
Wastewater from a food-manufacturing plant with a low concentration of organic matter was treated at 37 centigrade in an anaerobic fluidized-bed reactor or in an upflow anaerobic sludge blanket. As the influent TOC (total organic carbon) concentration decreased, the TOC removal efficiency in these reactors decreased from 85% to 65%. The concentration of suspended solids in the effluent could be reduced to 20 mg/l, which corresponded to 7% of that in the influent. The effluent from both reactors was treated aerobically in a fixed-bed reactor. The TOC concentration and optical density of effluent from the aerobic treatment were reduced to 5 mg/l and 0.005, respectively. When the effluent treated anaerobically or aerobically was passed over an activated carbon column, the effluent TOC concentration was reduced to 2 to 3 mg/l. The conductivity in raw wastewater was remarkably reduced on an ion-exchange resin column. Ultra-pure water for industrial ...
Anaerobic treatment of olive oil mill wastewaters (COD up to 220 kg/cubic m) is feasible, and the most promising results were obtained on UASB reactors, both at laboratory and pilot scale (tank capacity 15 litres and 5 cubic m), fed on diluted waste (COD = 13-18 kg/cubic m). Volumetric loading rates ranging from 16-21.5 kg COD/cubic m/day and 70% removal efficiencies were obtained with these digesters. Start-up of UASB reactors fed on olive oil mill waste is a delicate step which still has to be fully controlled and optimized. The best results were obtained by starting with very diluted waste (COD = 5 kg/cubic m). Granulation of the sludge, as achieved in Dutch UASB digesters fed on sugar beet wastewaters, was not obtained, but, even so, the settleability of the sludge was very good. 22 references.
PCR detection of genetic material of the parasites present in faeces may be an alternative for microscopic and serological tests routinely used for diagnosing parasitic enteral infections. However, small amount of target DNA combined with low efficiency of total DNA extraction, and presence of PCR inhibitors in the samples to be amplified, may cause false negative detection results. The aim of this work was to evaluate the impact of DNA isolation procedure used on the amplification of DNA fragments from the genomes of protozoan Cryptosporidium parvum and the nematode Trichinella spiralis. Two methods based on different principles of biological material lysis were evaluated; NucliSENS miniMAG employing simultaneously applied chemical lysis and mechanical disruption or mechanical disruption followed by enzymatic lysis in case of QIAamp DNA Stool Mini Kit. Both of the analyzed systems for nucleic acids purification allowed isolation of DNA from ...
From 1991 to 1996, key studies on the reutilization, treatment, and disposal technology of hazardous wastes have been incorporated into the national plan for environmental protection science and technology. At present, the research achievements have been accomplished, have passed national approval, and have been accepted. The author of this paper, as leader of the national group for this research work, expounds the newest achievements of the studies involving four parts: (1) the reutilization technology of electroplating sludge, including the ion-exchange process for recovering the sludge and waste liquor for producing chromium tanning agent and extracting chromium and colloidal protein from tanning waste residue; on the recovery of heavy metals from the electroplating waste liquor with microbic purification; on the demonstration project of producing modified plastics from the sludge and the waste plastics; and on the demonstration of the recovery of heavy metals ...
Full text: There are following general tendencies linking to SNF and radioactive waste management (RWM) in the Russian nuclear industry now. The intention to use the closed nuclear fuel cycle based on power water reactors and fast reactor. The intensification of measures aimed at the solution of 'nuclear legacy' from defenses programs of USSR. The intention to improve the existing national RW management infrastructure in the near years by means of the creation of a centralized national system (including managing corporation responsible for operation of long-storage and disposal facilities of conditioned RW). The main aims radioactive waste management (RWM) in nuclear power plants (NPP) for the next 10-15 years are to equip all NPPs with the necessary set of facilities for conditioning of the stored and currently generated RW with packaging the end-product into containers, to build regional NPPs RW repositories and to introduce evaporator bottoms selective ...
Rapid detection and characterization of food borne pathogens such as Escherichia coli O157:H7 is crucial for epidemiological investigations and food safety surveillance. As an alternative to conventional technologies, we examined the sensitivity and specificity of nucleic acid microarrays for detecting and genotyping E. coli O157:H7. The array was composed of oligonucleotide probes (25-30 mer) complementary to four virulence loci (intimin, Shiga-like toxins I and II, and hemolysin A). Target DNA was amplified from whole cells or from purified DNA via single or multiplexed polymerase chain reaction (PCR), and PCR products were hybridized to the array without further modification or purification. The array was 32-fold more sensitive than gel electrophoresis and capable of detecting amplification products from < 1 cell equivalent of genomic DNA (1 fg). Immunomagnetic capture, PCR and a microarray were subsequently used to detect 55 CFU ml-1 (E. coli O157:H7) ...
The Kemp's Ridley sea turtle, Lepidochelys kempi, is an endangered species. The National Marine Fisheries Service's Head Start program is part of an international operation to save the turtles from extinction. Under the Head Start program, eggs from the Ridley's only known wild nesting beach at Rancho Nuevo in Mexico are transported to Padre Island on the Texas coast to be hatched. The head start enables the turtles to develop a survival advantage. The principal objective was to develop baseline waste-characterization data required to design a waste-water treatment scheme for the Galveston Head Start facility. As a secondary objective, preliminary testing of some filtration components was undertaken to determine which units were most appropriate for inclusion in a wastewater treatment scheme.
A kinetic study of the degradation by ozone of eight phenolic acids present in wastewaters from olive oil mills has been performed by using a competition kinetic method. The selected phenolic acids are: caffeic, p-coumaric, syringic, vanillic, 3,4,5-trimethoxybenzoic, veratric, p-hydroxy-benzoic, and protocatechuic. The influence of the operating variables (temperature, pH, and ozone partial pressure in the gas stream) is established, and the stoichiometric ratios for the individual direct reactions between ozone and each acid are determined. Once the reaction rate constants are evaluated, they are correlated as a function of temperature and pH into kinetic expressions which are provided for every phenolic acid. The global process occurs in the fast and pseudo-first-order kinetic regime of absorption, a condition required by the competition model to be used.
This report reviews coal conversion processes which may be introduced in Canada within the next decade if interest in alternate energy technologies continues. A detailed review was conducted on coal liquefaction and gasification projects worldwide including information on individual proprietors, process technologies used, their present status and available environmental data. Further assessment of emissions and wastes emanating from commercial-scale plants was used to determine significant or potentially significant wastestreams connected to the various technologies, particularly wastewater discharges. Emphasis was placed on those technologies that are close to commercialization in Canada, i.e. SASOL II-type liquefaction facility at Hat Creek. Available information on wastewater treatment/reuse is also included in this report.
Abstract In this research, the efficiency of electrocoagulation treatment process using aluminum electrodes to treat synthetic wastewater containing Reactive Red198 (RR198) was studied. The effects of parameters such as voltage, time of reaction, electrode connection mode, initial dye concentration, electrolyte concentration, and inter electrode distance on dye removal efficiency were investigated. In addition, electrical energy consumption, electrode consumption, and operating cost at optimum condition have been investigated. The results showed that dye and chemical oxygen demand removals were 98.6 and 84%, respectively. Electrode consumption, energy consumption and operating cost were 0.052-kg/m3, 1.303-kWh/m3 and 0.256-US$/m3, respectively. Dye removal kinetic followed first order kinet...
The bibliography contains citations concerning the use of dialysis in the treatment of wastewaters. Techniques for the removal of metals, ammonia, waste acids, nitrates, and phosphates are described. Special attention is given to the desalination of liquid wastes. Applications of this technology to the treatment of effluent from the agrochemical, petrochemical, tanning, and electroplating industries are discussed. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)
A rapid and accurate method for the direct simultaneous determination of nitrate and nitrite is proposed. The method is applied to the determination of nitrate and nitrite in rainwater and wastewater without preliminary separation. The determinations are performed by a CPA matrix method with ultraviolet spectrophotometric detection. The results obtained are in agreement with those obtained by conventional methods for the determination of nitrate and nitrite.
The hazardous and toxic nature of some of the constituent such as nitrite in the aquaculture wastewater is of major concern. Present study focuses the removal of nitrite from the aquaculture wastewater prior to disposal. Effect of certain operational parameters such as electrode material, current density, initial pH, and electrode spacing on nitrite removal from aquaculture wastewater was elucidated. Better nitrite removal efficiency achieved when nickel used as compared to stainless steel, graphite and aluminum electrodes. Nitrite removal is positively related to the current density however, increase is up to 31.4% when current density increased from 2.5 to 9.3 mA/cm/sup 2/. Further increase in current density does not improve the process efficiency. Removal efficiency of electrochemical process decreased with the increase in initial pH of test solution. However, with the passage of time this difference is diminishing. ...
The bibliography contains citations concerning Federal and state laws and management programs for the protection and use of inland wetlands. Utilization of wetlands to control highway runoff and community wastewater is discussed. Wetlands protection programs, restoration projects, resource planning, and wetlands identification methods are cited. References to coastal and salt water wetlands are not included in this bibliography. (Contains 250 citations and includes a subject term index and title list.)
This proceedings CD ROM contains 127 papers on developing and evaluating engineering approaches to wetlands and river restoration. The latest engineering developments are discussed, providing valuable insights to successful approaches for river restoration, wetlands restoration, watershed management, and constructed wetlands for stormwater and wastewater treatment. Potential solutions to a wide variety of ecosystem concerns in urban, suburban, and coastal environments are presented.
...Chapter 11 Aqueous Solutions Chapter 11 Aqueous Solutions Download the entire chapter (PDF-136k) Drilling to China More water than rivers Saving the aquifer Drying with Xeriscapes Everywhere in the house Rainwater and graywater Creating urban watersheds Wastewater equals ...3851 Powered by Intrcomm Technology's SMC ...
A simple and rapid procedure was developed for the purification of cyclotron-produced "2"0"3Pb via the "2"0"3Tl(d,2n) "2"0"3Pb reaction. A Pb(II) selective ion-exchange resin, with commercial name Pb Resin from Eichrom Technologies, Inc., was used to purify "2"0"3Pb from the cyclotron-irradiated Tl target with excellent recovery of the enriched Tl target material. The purified "2"0"3Pb was used to radiolabel the monoclonal antibody Herceptin. The in vitro and in vivo properties of the "2"0"3Pb radioimmunoconjugate were evaluated.
We have developed a process for chemical purification of carbon nanotubes for solution-processable thin-film transistors (TFTs) having high mobility. Films of the purified carbon nanotubes fabricated by simple drop coating showed carrier mobilities as high as 164 cm2V?1s?1, normalized transconductances of 0.78 Sm?1, and on/off current ratios of 106. Such high performance requires the preparation of a suspension of micrometer-long and highly purified semiconducting single-walled carbon nanotubes (SWCNTs). Our purification process includes length and electronic-type selective trapping of SWCNTs using recycling gel filtration with a mixture of surfactants. The results provide an important milestone toward printed high-speed and large-area electronics with roll-to-roll and ink-jet device fabri...
A practical hands-on course encompassing enzyme purification, biochemical characterization, and crystallization that completed the course work of 350 second-year bachelor students enrolled in molecular biology/biochemistry was given at the Universite Louis Pasteur of Strasbourg (France). The experimental part of the practical dealt entirely with the model protein lysozyme isolated from hen egg-white. It was designed as a research project to give students the possibility to practice biochemical methods such as chromatography, electrophoresis, and spectrophotometry. It also included enzyme activity assay and protein crystal growth that are usually taught in master-level courses. The organization of the practical work and the related experimental procedures are described and discussed.
Waste cooking oil can be recovered and processed into animal feed additives after purification. Unfortunately, the traditional purification processes are insufficient for the removal of the harmful compounds formed during frying, mainly about malondialdehyde and other 2-thiobarbituric acid reactive substances. In the present paper, firstly, a simple and reliable HPLC method was developed to measure the content of malondialdehyde in purified waste cooking oil. The detection limit and the standard recovery of the analysis method are 1.20x10-5gl-1 and 96.5-99.2%, respectively, which is accurate and valid enough for the detection of malondialdehyde in waste cooking oil. Furthermore, the removal of malondialdehyde and other 2-thiobarbituric acid reactive substances from waste cooking oil was in...
Since artificial organs are intended to replicate chemical processes, knowledge of chemical engineering is essential in their design so that they will function with the maximum efficiency. The most commonly used artificial organ is the artificial kidney, a machine that performs a treatment known as hemodialysis. This process cleanses the bodies of renal failure patients by dialysis and filtration which are simple physiochemical processes. Hemodialysis membranes act to remove accumulated uremia toxins, excess ions and water from the patient via the dialysate, and to supply from the dialysate those ions that are insufficient. This paper describes dialysis membranes and dialyzers for blood purification, the solute transport mechanism of the membrane, and a technical evaluation of the dialysis membrane. Lastly, the next generation of artificial kidney is reviewed. 71 refs., 12 figs., 7 tabs.
Phycocyanin - a major phycobiliprotein constitutively produced by many cyanobacteria hold several promising applications in diagnostics, biomedical research, and therapeutics. This paper discusses a novel rapid method for the purification of cyanobacterial phycocyanin (C-PC) from Phormidium fragile using hydrophobic interaction chromatography. The protein was extracted and concentrated by grinding under liquid nitrogen and ammonium sulfate fractionation. C-PC was purified by single step hydrophobic interaction chromatography. Purified phycocyanin showed absorbance maximum (lmax) at 624nm. The criterion of purity (R) achieved was 4.52. Phycocyanin to phycoerythrin and phycocyanin to allophycocyanin purity ratio were 3.85 and 7.49, respectively. The purified protein showed a pI of 5.2 and ha...
One of the refinements of modern Nuclear Medicine is the capacity of providing dynamic and kinetics images of the administered radiopharmaceutical, reproducing its transport mechanism, action sites, receptor binding and excretion route. With the continues technological advances new radiopharmaceuticals have been developed in order to express higher specificity and with higher characters of affinity between receptor/complex. One radiopharmaceutical is formed by a reagent or bio molecule that has in its structure a radioisotope, that has the objectives of carrying it to the organs of affinity or to benign or malign tumoral process. Somatostatin inhibits the growing and proliferation of several tumoral cells. Somatostatin analogs bind to somatostatic receptors that are expressed in different kind of neoplasia DOTA-LANREOTIDE (DOTALAN) is an octapeptide analog to somatostatin. The interest of labeling the bio conjugate with gallium-67 in Nuclear Medicine comes from its physical, chemical ...
A two-step purification protocol was used in an attempt to separate the constitutive NAD(P)H-nitrate reductase [NAD(P)H-NR, pH 6.5; EC 1.6.6.2] activity from the nitric oxide and nitrogen dioxide (NO(x))...Full Text Available
Lectures were held on forest and wood management, the forest as an energy source and the emission problem of wood combustion, future emission limitating regulations for wood firing, influence of firing technique on air pollution abatement and constructive and operational air pollution abatement measures with manually and continuously fuelled furnaces.
Crude N,N-dialkylcarbamoylmethylphosphonates and phosphine oxide extractants, and particularly crude dihexyl N,N-diethylcarbamoylmethylphosphonate and octylphenyl N,N-diisobutylcarbamoyl phosphine oxide, are purified by distilling the crude materials in a thin film evaporator. Preferably, the crude materials are reacted with concentrated hydrochloric acid and then with aqueous sodium hydroxide prior to distillation in the thin film evaporator to hydrolyze impurities contained in them. The purified extractants are useful for extracting actinides and lanthanides from liquid waste streams. (author).
Crude N,N-dialkylcarbamoylmethylphosphonates and phosphine oxide extractants, and particularly crude dihexyl N,N-diethylcarbamoylmethylphosphonate and octylphenyl N,N-diisobutylcarbamoyl phosphine oxide, are purified by distilling the crude materials in a thin film evaporator. Preferably, the crude materials are reacted with concentrated hydrochloric acid and then with aqueous sodium hydroxide prior to distillation in the thin film evaporator to hydrolyze impurities contained in them. The purified extractants are useful for extracting actinides and lanthanides from liquid waste streams. (author).
NADP:malic enzyme from corn (Zea mays L.) leaves was purified by conventional techniques to apparent homogeneity as judged by sodium dodecyl sulfate-polyacrylamide gel electrophoresis....Full Text Available
A new sugarcane (Saccharum officinarum L.) fructanase which hydrolyzes both high molecular weight polysaccharides ∣Fructose4:Galactitol5∣n...Full Text Available
The extremely thermophilic anaerobic archaeon strain B1001 was isolated from a hot-spring environment in Japan. The cells were irregular cocci, 0.5 to 1.0 μm in diameter. The new isolate grew...Full Text Available
The thermostable Thermus aquaticus DNA polymerase (Taq Pol) has been the key factor in transforming the initial PCR method into one with huge impact in molecular biology and biotechnology. Therefore, the development of effective affinity adsorbents for the purification of Taq Pol, as well as other DNA polymerases, attracts the attention of the enzyme manufacturers and the research laboratories. In this report we describe a simple protocol for the purification of Taq Pol from E. coli lysates, leading to enzymes of high specific activity and purity. The protocol is based on a single affinity chromatography step, featuring an immobilized ligand selected from a structure-biased combinatorial library of dNTP-mimetic synthetic ligands. The ligand library was screened for its ability to bind and purify Taq Pol from E. coli lysates. One immobilized ligand (mABSGu) of the general formula X-Trz-Y, bearing 9-aminoethylguanine (AEGu) and aniline-2-sulfonic ...
Ocular and urogenital tract infections with Chlamydia trachomatis can progress to chronic inflammatory diseases that produce blindness and tubal infertility. The pathophysiology of these chronic disease...Full Text Available
The use of filters of activated-charcoal particles in drinking-water purification plants assists in the elimination of organic micropollutant substances. The authors report on a study which sought to investigate the mechanism of organic matter; they describe the experimental programme, which used different size ranges of mineral-based activated charcoal, present the experimental findings and discuss the results. 16 references.
We have developed a new expression vector, pcIts ind+, based upon the powerful rightward promoter of bacteriophage lambda, which is controlled by a temperature-sensitive...Full Text Available
Conversion of coal gas into liquid products is a multistep process which involves numerous unit processes. Compared with similar processes using natural gas as feedstock, there are challenges, particularly with the gas purification. There are, however, also advantages when using a carbon-monoxide-rich gas which ultimately may result in a greatly simplified process. This paper discusses the challenges when converting a gas from an entrained coal gasifier into a liquid product and the paper presents the various options available. The following issues will be touched upon: sour gas shift and adjustment of the H{sub 2}/CO ratio; acid Gas Removal (AGR) - when and how; syngas purification; methanol and combined methanol/DME synthesis; gasoline synthesis; future integrated processes. Here, various options are available depending on the gasifier; not only dry or slurry feed but also the question of quench as well as the selected scrubbing temperature ...
The enzyme indol-3-ylacetylglucose synthase (UDP-glucose:indol-3-ylacetate beta-D-glucosyltransferase) catalyses the reaction: [formula: see text] This is the first step in the series of reactions leading...Full Text Available
The mission of the Heavy Water portion of D Area (or 400 Area) at SRS is to purify the site inventory of heavy water for storage in the Reactor Areas for future DOE missions.
[5'-"3H]-3'-Azido-3'-deoxythymidine (3) was prepared at a specific activity of 14.0 Ci/mmol by a two-step synthetic sequence involving controlled oxidation of the unlabelled compound (1) to the 5'-aldehyde (2) followed by reduction with ["3H]-NaBH_4. Purification was performed by preparative TLC. The radiochemical purity was 99.2%. (author).
Biogas, produced from anaerobic digestion of organic matter in domestic, industrial and rural wastewaters and residuals, represent an alternative and renewable source of energy, with growing use worldwide. In Brazil, high population and its spatial concentration and expressive agricultural and agricultural-industrial production indicate a substantial potential of biogas production. The results presented in this work show a potential of biogas production of almost 2 billion cubic feet a day of CH{sub 4}. Viability of biogas production and use depends substantially on project scale. Generally, biogas projects are viable from landfills and domestic wastewater treatment for populations higher than 50,000 inhabitants and swine and dairy farms with at least 5,000 and 1,000 animals, respectively. Biogas is also competitive when compared to fossil fuels used in industry and transport. Despite incentive mechanisms for biogas production and use, like ...
Increasingly, governments enact more stringent regulations governing nitrogen and phosphorus in the discharge effluent of wastewater treatment plants. Scientists know that nitrogen and phosphorus accelerates the eutrophication of lakes and reservoirs and stimulates algal growth. Ammonia has proven to be toxic to aquatic life forms, including fish. Engineers favour Biological Nutrient Removal (BNR) over chemical addition to wastewater treatment. Sequencing Batch Reactors (SBRs), a type of bioreactor requiring less land, provide the anaerobic, anoxic, and aerobic zones necessary for BNR. Methanol was used as an effective external source of carbon for denitrification but lacked research. The authors remedied this situation and some of the results were available. They indicated that the addition of methanol in the SBR increased solids production in the SBR, leading to increased sludge wasting to the aerobic digester. All aspects of the sludge ...
In situ toxicity tests were designed for Ceriodaphnia dubia and Chironomus tentans as part of a larger study designed to assess the effectiveness of constructed wetlands for the treatment of wastewater produced by oil production at Suncor OSG. The artificial wetlands were 50m long by 3m wide, with three replicates of the control and the treatment. Each wetland had four sample sites equidistant along its length, creating a gradient of treatment from site A being the most toxic to site D being the least toxic. Each test was conducted twice during the summer of 1994. Both the Ceriodaphnia and Chironomus test cages were a flow through design to allow for maximal exposure to the water within the wetlands. Mortality and reproduction were used as endpoints for Ceriodaphnia, whereas mortality and growth were used as endpoints for the Chironomus test. Test durations were fifteen and ten days respectively. Chironomus had very high mortality along the entire wetlands whereas ...
This study examined the atmospheric pollution created by some waste treatment and disposal facilities in the State of Kuwait. Air monitoring was conducted in a municipal wastewater treatment plant, an industrial wastewater treatment plant established in a petroleum refinery, and at a landfill site used for disposal of solid wastes. Such plants were selected as models for waste treatment and disposal facilities in the Arabian Gulf region and elsewhere. Air measurements were made over a period of 6 months and included levels of gaseous emissions as well as concentrations of volatile organic compounds (VOCs). Samples of gas and bioaerosols were collected from ambient air surrounding the treatment facilities. The results obtained from this study have indicated the presence of VOCs and other gaseous pollutants such as methane, ammonia, and hydrogen sulphide in air surrounding the waste treatment and disposal facilities. In some cases the levels ...
The technology developed here will exploit the ability of microorganisms to remove dissolved metals from aqueous solutions. Microbial sorbents for uranium will be immobilized biosorbents will be deployed ex situ within flow-through reactors for the continuous or semicontinuous treatment of recovered wastewaters. The proposed technology will primarily be applied within a pump-and-treat process using immobilized biosorbents for the large-scale, long-term remediation of uranium-laden surface water or groundwater impoundments (environmental restoration). The technology may be equally useful as an ``end-of-pipe`` treatment of process effluents (waste management). Successful operation of this process will achieve immobilization of the targeted waste and accompanying volume reduction.
Case studies are presented for treatment of refinery wastes in a pilot-scale thin-film evaporator, the removal of volatiles from industrial wastewater for two steam strippers, and the removal of semivolatiles from water by steam stripping followed by liquid-phase carbon adsorption. The report provides data on removal efficiency, air emissions, process residuals, treatment costs, and process limitations. Details on sampling and analytical procedures, quality assurance, and process data are contained in the Appendixes (Volume II).
Case studies are presented for treatment of refinery wastes in a pilot-scale thin-film evaporator, the removal of volatiles from industrial wastewater for two steam strippers, and the removal of semivolatiles from water by steam stripping followed by liquid-phase carbon adsorption. The report provides data on removal efficiency, air emissions, process residuals, treatment costs, and process limitations. Details on sampling and analytical procedures, quality assurance, and process data are contained in the Appendixes (Volume II).
An efficient adsorption process is developed for the decontamination of trivalent chromium from tannery effluents. A low cost activated carbon (ATFAC) was prepared from coconut shell fibers (an agricultural waste), characterized and utilized for Cr(III) removal from water/wastewater. A commercially available activated carbon fabric cloth (ACF) was also studied for comparative evaluation. All the equilibrium and kinetic studies were conducted at different temperatures, particle size, pHs, and adsorbent doses in batch mode. The Langmuir and Freundlich isotherm models were applied. The Langmuir model best fit the equilibrium isotherm data. The maximum adsorption capacities of ATFAC and ACF at 25 deg. C are 12.2 and 39.56 mg/g, respectively. Cr(III) adsorption increased with an increase in temperature (10 deg. C: ATFAC-10.97 mg/g, ACF-36.05 mg/g; 40 deg. C: ATFAC-16.10 mg/g, ACF-40.29 mg/g). The kinetic studies were conducted to delineate the effect of temperature, ...
This study describes the feasibility of anaerobic treatment of complex phenolics mixture from a simulated synthetic coal wastewater using four identical 13.5 L (effective volume) bench scale hybrid up-flow anaerobic sludge blanket (HUASB) (combining UASB + anaerobic filter) reactors at four different hydraulic retention times (HRT) under mesophilic (27 #+-# 5 "oC) conditions. Synthetic coal wastewater with an average chemical oxygen demand (COD) of 2240 mg/L and phenolics concentration of 752 mg/L was used as substrate. The phenolics contained phenol (490 mg/L); m-, o-, p-cresols (123.0, 58.6, 42 mg/L); 2,4-, 2,5-, 3,4- and 3,5-dimethyl phenols (6.3, 6.3, 4.4 and 21.3 mg/L) as major phenolic compounds. The study demonstrated that at optimum HRT, 24 h, and phenolic loading rate of 0.75 g COD/(m"3-d), the phenolics and COD removal efficiency of the reactors were 96% and 86%, respectively. Bio-kinetic models were applied to data obtained from ...
An examination of chemical and radiological characteristics of RI organic liquid waste, wet oxidation by Fenton reaction and decomposition liquid waste treatment process were studied. These items will be applied to develop the equipment of wet oxidation and decomposition liquid waste treatment mixed processes for the safe treatment of RI organic liquid waste which is consisted of organic solvents such as toluene, alcohol and acetone. Two types of toluene solutions were selected as a candidate decomposition material. As for the first type, the concentration of toluene was above 20 vol percent. As for the second type, the solubility of toluene was considered. The decomposition ration by Fenton reaction was above 95 percent for both of them. From the adsorption equilibrium tests, a -Na{sup +} substituted/acid treated activated carbon and Zeocarbon mixed adsorbent was selected for the fixed adsorption column. This mixed adsorbent will be used to obtain the basic design data of liquid waste ...
Aminocyclopropane 1-carboxylic acid (ACC) synthase, a pyridoxal phosphate utilizing enzyme, catalyzes the conversion of S-adenosylmethionine to ACC, the rate limiting step in the biosynthesis of the plant hormone, ethylene. Ethylene, besides being involved in normal plant growth processes, is also produced in response to stress, e.g. wounding, pathogen infection, etc. The authors report the partial purification (400 fold) of ACC synthase from wounded pink tomato pericarp by classical techniques including ammonium sulfate precipitation, ion exchange and phenyl sepharose chromatography. Further purification results in a decrease in specific activity apparently due to the instability of the enzyme and the low levels present in plant tissue. Radiolabeling of a pyridoxal phosphate-utilizing protein in the ACC synthase enriched fraction was achieved. Evidence that this radiolabeled protein is ACC synthase will be presented. Amino acid sequence ...
The {sup 176}Ybn,{gamma}{sup 177}Yb-{beta}{sup -}{yields}{sup 177}Lu process was investigated to provide no-carrier-added (nca) {sup 177}Lu. The radiochemical separation of the {sup 177}Lu from the macro-amounts of the ytterbium target based on the cementation process, i.e. the selective extraction of Yb by Na(Hg) amalgam from Cl{sup -}/CH{sub 3}COO{sup -} electrolytes, followed by a final cation exchange purification. The cementation separation process provides a decontamination factor of Yb(III) of 10{sup 4}, the cation exchange purification adding a decontamination factor of >10{sup 2}. The nca {sup 177}Lu is available in radiochemically pure form despite the chemical similarity of the lanthanides with 75{+-}5% overall separation yield within 4-5 h. It can be used to synthesise nca {sup 177}Lu labelled radiotherapeuticals.
In nuclear power plant Paks, Hungary, alkaline oxidative (NaOH, KMnO_4, H_2O) and acidic reductive (citric- and oxalic acid, water) liquids are using for the decontamination of primary circuit equipment (main liquid circulating pumps, steam generators, pipelines etc). The above mentioned decontamination liquids are containing "1"1"0"mAg, "9"5Nb, "5"4Mn, "5"8 Co, "6"0Co, "5"1 Cr, "1"2"4 Sb radioisotopes, summarized radioactivity is between 10"3-8x10"4 kBq/dm"3 liquid. The decontamination liquid can be cleaned with reactive adsorption (active carbon) and ion-exchange process at elevated temperature (333-368 K) in multilayered columns. After purification the summarized radioactivity for "5"4Mn, "6"0Co, and "1"1"0"mAg are in the outlet liquid below 1 kBq/dm"3. Decontamination factor DF#approx =#10"3-10"4, volumetric reduction factor VRF#approx =#50-500.
This R and D project is planed to supply domestic demands of Mo-99 through fission route, and consequently this project will be expected to rise up utilization of HANARO and KAERI's capability for marketing extension into domestic and oversea radiopharmaceutical market. HEU and LEU target types are decided and designed for fission Mo-99 production in domestic. Experimental study of target fabrication technology was performed and developed processing equipments. And conceptual design of target loading/unloading in/from HANARO device are performed. Tracer test of Mo-99 separation and purification process was performed, test results reach to Mo-99 recovery yield above 80% and decontamination factor above 1600. Combined Mo-99 separation and purification process was decided for hot test scheduled from next year, and performance test was performed. Conceptual design for modification of existing hot cell for fission Mo-99 production facility ...
The authors discuss radioimmunoassays (RIAs) for eicosanoids widely used in the field of experimental, clinical and pharmacological research. The main drawback of RIAs is the possibility of low specificity. This was clearly demonstrated during the controversy on plasma levels of 6-keto-PGF_1 #alpha#, the stable hydrolysis product of PGI_2. When extensive purification including reverse phase high pressure liquid chromatography (rp-HPLC) was performed prior to the RIA for 6-keto-PGF_1 #alpha# the levels were at least one order of magnitude less than previously claimed, and did not support the so-called circulating hormone hypothesis.
Passage of neon gas through activated charcoal is planned to be the primary method of removing impurities from the liquid neon scintillator in the CLEAN experiment. In order to quantify this technique, the breakout curves for hydrogen, nitrogen, argon and krypton impurities in neon-saturated activated charcoal were measured. Adsorption coefficients and the number of theoretical stages were measured for hydrogen in the temperature range between 300 and 80 K, nitrogen between 300 and 200 K, and argon between 300 and 190 K. The adsorption coefficient for krypton was measured at 300 K.
The basic approach to radioactive labeling techniques in hemoglobin identification consists of mixing 14C labeled normal carrier globin with 3H labeled unknown globin and carrying out the subsequent separations and purifications looking at the distribution of 3H and 14C radioactivity. This technique was devised to ascertain the amino acid substitution in Hb Indianapolis and was instrumental in solving the structure of Hb Vicksburg. It was also useful in determining the purity of gamma-chains from cultures of human and baboon erythroid progenitors. Another use of this technique would be in identifying aberrant peaks of radioactivity in chain separation chromatograms, such as ''pre-peaks''.
The paper presents results of measurements of the natural radioactivity of tap water where samples were taken in front of, and behind the ceramic filter commonly used in houses for the purification of tap water. Altogether, 289 samples were taken, processed and measured during 1985-1986 in Kuwait. Results reveal the fact that ceramic filters reduce substantially the natural radioactivity in water (the 'gross' alpha activity reduced by the factor 2.18 #+-# 18%; the 'gross' beta by 1.53 #+-# 1.6%. (author).
Tendency of 12Kh18N10T steel tube samples to intergranular corrosion (IGC) is investigated by an express electrochemical method in the 10% solution of H_2SO_4+0.0025 g/l of KCNS. Tendency to IGC is mainly detected on the internal surface of tube samples. It is shown that the tendency to INC under plant conditions is caused by surface carburization under its incomplete purification from the graphite lubrication.
The main activities developed at 'Instituto de Energia Atomica' Sao Paulo, Brazil, on the recovery of uranium from ores, the purification of uranium and thorium raw concentrates and their transformation in nuclear grade compounds, are reviewed. The design and assemble of pilot facilities for ammonium diuranate (ADV) uranium tetrafluoride, uranium trioxide, uranium oxide microspheres, uranyl nitrate denitration, uranim hexafluoride and thorium compounds are discussed. The establishment of analytical procedures are emphasized.
The reactor fuel cycle based on uranium is described. The various stages in the cycle include mining of uranium ores followed by crushing and grinding, leaching and purification of leach liquor by ion exchange resin process or solvent extraction process, refining of uranium concentrate (yellow cake) by digesting with HNO_3 and then solvent extracting uranyl nitrate with TBP, conversion of uranyl nitrate to uranium hexafluoride, production of uranium metal, uranium enrichment, fabrication of reactor fuel elements and reprocessing of the spent fuel. Chemical reactions wherever they are involved are explained. (M.G.B.).
Processes of production and purification (necessary for fabricating fuel elements) of powdery uranium dioxide with particle size up to 1000 #mu#m and more have been studied. Developed is continuous process of UO_2 production with above particle size by converting uranium hexafloride into UO_2 solid particles in fluidized bed while their interaction with water vapor and hydrogen on the uranium dioxide nucleus material. The method allows to conduct continuous selection from the apparatus of UO_2 powder fraction with particle size near 1000 #mu#m without nucleus material additional feed.
The report is divided into three sections. The first section contains a general introduction to ion exchange resins used in various processes, the second section describes characteristic properties of the polymer materials and the inter relation between them. This will, in turn, be useful to interpret the data obtained from the various tests carried out on the resins in the laboratory. In the third section of the report, are given the details of each method used for a particular test to be carried out on a routine basis. Each method describes the principle involved, the reagents and apparatus used in the experiment, the actual procedure and calculations and recording of the data. 3 refs. (author).
In the United States, economic growth increasingly requires that greater volumes of freshwater be made available for new users, yet supplies of freshwater are already allocated to existing users. Currently, water for new users is made available through re-allocation of xisting water supplies-for example, by cities purchasing agricultural water rights. Water may also be made available through conservation efforts and, in some locales, through the development of ''new'' water from non-traditional sources such as the oceans, deep aquifer rackish groundwater, and water reuse.
An experimental verification for long-term performance of a Pd-Ag permeation in ITER tritium fusion cleanup units (FCU) is needed. In addition, information is required on the influence of tritium and {sup 3}He decay on the physical and chemical properties of Pd-Ag alloys (V-1). The results of the investigations of alloys (V-1) (mechanical properties and microstructure) after long-term usage exposition in tritium are given in this report. The experimental conditions (temperature, pressure, clearance, {sup 3}He concentrations) and the previous conclusions on the V-1 alloy performance are presented. (orig.).
This is an adsorbent for removal of heavy metal impurities from gases. In addition to activated charcoal and ferric chloride, it contains a nonwoven dacron filter material to increase the purification level. The filter material has the following mass % composition: 27-54 activated charcoal, 7-35 ferric chloride, the remainder dacron filter material. The activated charcoal is applied to the dacron filter and the resulting mixture is treated with a ferric chloride solution. The activated charcoal is applied in the form of a suspension with a particle diameter of 0.1-0.16 mm. The treatment solution is 3-20% ferric chloride.
A useful method for preparing radioiodinated photoaffinity labels from alkyl anilines which offer significant advantages over present methods is described. The one-pot synthesis gives good radiochemical yields (40-64%) of pure, high specific activity (350-1500 mCi/#mu#mol) "1"2"4I labelled iodaryl azides while minimising manipulation of radioactive materials. Purification of the ["1"2"5I]iodoazido photoaffinity labels is achieved by high performance liquid chromatography. (author).
A useful method for preparing radioiodinated photoaffinity labels from alkyl anilines which offer significant advantages over present methods is described. The one-pot synthesis gives good radiochemical yields (40-64%) of pure, high specific activity (350-1500 mCi/{mu}mol) {sup 124}I labelled iodaryl azides while minimising manipulation of radioactive materials. Purification of the ({sup 125}I)iodoazido photoaffinity labels is achieved by high performance liquid chromatography. (author).
The methods introduced for the field of cleaning waste water can be classified under various processes. Chemical oxidation is done with ozone, hydrogen peroxide and ultraviolet irradiation with subsequent biological decomposition. Another method is ultra-filtration with recovery of valuable materials or waste water ponds with algae biomass to decompose ammonium compounds, nitrates and phosphates. (EF) [Deutsch] Die auf dem Gebiet der Abwasserreinigung vorgestellten Methoden kann man in verschiedene Verfahren einordnen. Die chemische Oxidation erfolgt mit Ozon, Wasserstoff-Peroxid, UV Bestrahlung und anschliessenden biologischen Abbau. Eine andere Methode ist die Ultrafiltration mit Rueckgewinnung von Wertstoffen oder Abwasserteiche mit Algenbiomasse zum Abbau von Ammoniumverbindungen, Nitraten und Phosphaten. (EF)
During the first and second quarters of 1994 air samples were collected and analyzed from 54 air particulate/halogen sampling stations, 10 noble gas sampling stations and 19 tritiated water vapor sampling stations. Surface water samples were collected and analyzed from 12 open water supply reservoirs, 8 natural springs, 2 wastewater containment ponds and 9 sewage lagoons. Groundwater samples were obtained brom 10 potable and 1 non-potable supply wells, and 8 drinking water consumption points. Ambient radiation levels were measured at 193 locations.
The extent to which a novel wash-off process using polyamide beads removed five different types of dye from three different types of fibre was similar to that achieved using conventional aftertreatments. Whilst bead wash-off and the conventional aftertreatments were of similar duration and temperature, conventional aftertreatment employed a 10:1 or 20:1 liquor ratio whereas bead wash-off used a < 1:1 liquor ratio. As vagrant dye was adsorbed onto the bead material during wash-off, the low amount of wastewater generated contained little residual dye, thereby offering the potential of reduced environmental and cost benefits. Bead wash-off did not impair the fastness of two non-metallised acid dyes on nylon 6,6 to washing at 60 ?C.
A series of modifications which increased the capacity of Canadian Electrolytic Zinc's Valleyfield plant from 220,000 MT/year to 260,000 MT/year during the last decade is discussed, combined with an an overview of the plant's operations. The modifications included modernisation of the waste disposal methods and facilities, such as a new high-density sludge wastewater treatment process, a new process to remove selenium from weak acid solutions and the jarofix process. Roasting capacity also has been improved by recent investments in new cooling coils, rebricking, oxygen enrichment and process automation. In addition to increases in refining capacity, the improvements also enabled the company to minimize its impact on the environment and the community.
Combined sewer overflows (CSOs) have been recognised as one of the serious sources of pollution to the water environment during rain events, although field surveys to investigate the effect of their magnitude and duration on receiving waters have been very limited. The fates of enteric viruses (norovirus G1, G2, enteroviruses) and coliforms were determined in the wastewater treatment plant on a fine day and on a rainy day. Not all microorganisms were reduced in the primary treatment, but were reduced in the secondary treatment. Occurrences of enteric viruses and levels of coliforms were surveyed in the receiving coastal area after a CSO event, with the profiles of the enteric viruses in the coastal seawater being almost at the same positive ratio for 4 d after the CSO event. PMID:15318519
The lignin, one of the main by-products of the pulp industry, can be used to remove dyes from textile wastewaters. The potential of the lignin for Brilliant Red HE-3B reactive dye removal from aqueous solutions at pH=1.5 was examined by the batch technique as a function of dye concentration, solution temperature and contact time. The Freundlich, Langmuir, Dubinin-Radushkevich and Tempkin adsorption isotherms were used to describe the data of sorption equilibrium and to determine its corresponding isotherm constants. The thermodynamic parameters DG, DH and DS were also determined; the obtained values show that the sorption of reactive dye on lignin is a spontaneous, endothermic and entropy-driven process. The kinetic of reactive dye sorption was analyzed using the pseudo-first order and pse...
To elucidate biosorption mechanism and removal efficiency of plant residues as a biosorbent to abate polycyclic aromatic hydrocarbons (PAHs) in wastewater, sorption of PAHs onto wood chips (WC), ryegrass roots (RR), orange peels (OP), bamboo leaves (BL), and pine needles (PN) were investigated. The structural characterization of the biosorbents was analyzed by elemental composition, BET-N2 surface area, and Fourier transform infrared spectroscopy. PAHs sorption to the selected biosorbents were compared and correlated with their structures. Biosorption isotherms fit well with Freundlich equation and the mechanism was dominated by partition process. The magnitude of phenanthrene partition coefficients (Kd) followed the order of PN>BL>OP>RR>WC, ranged from 2484+/-24.24 to 5306+/-92.49L/kg. Ex...
A wet air oxidation (WAO) process was applied to four selected pharmaceuticals (metoprolol, naproxen, amoxicillin, and phenacetin) individually dissolved in ultra-pure water, varying the temperature and oxygen pressure. Due to the moderate (amoxicillin) or low (metoprolol, naproxen, and phenacetin) efficiency found in the oxidation of these pollutants, a catalytic wet air oxidation (CWAO) process was then tested using a platinum catalyst supported on multi-walled carbon nanotubes (CNT). In this CWAO process, the pharmaceuticals were dissolved together in ultra-pure water and in four natural water matrices-a reservoir water, a groundwater, and two waters from different municipal wastewater treatment plants. On the basis of the measurements of their removals, a discussion is given of the inf...
A 1 MWe power plant using waste wood fuel is to be installed at a US Marine Corps base, which will supply all wood from a landfill site. The core energy conversion technology is a down-draft gasifier supplying approximately 150 Btu/scf gas to both spark ignition and diesel dual-fuel engine-generator sets. Features of the plant design include: (1) grinding wood fuel from a wide range of waste resources, (2) specialized screening for fines removal, (3) complete tar and other waste product control without landfill disposal, and (4) use of process heat for bulk fuel drying, gasifier air pre-heating, and wastewater evaporation.
This report estimates the economic and financial effects and the benefits of compliance with the proposed effluent limitations guidelines and standards for the Centralized Waste Treatment (CWT) industry. The Environmental Protection Agency (EPA) has measured these impacts in terms of changes in the profitability of waste treatment operations at CWT facilities, changes in market prices to CWT services, and changes in the quantities of waste management at CWT facilities in six geographic regions. EPA has also examined the impacts on companies owning CWT facilities (including impacts on small entities), on communities in which CWT facilities are located, and on environmental justice. EPA examined the benefits to society of the CWT effluent limitations guidelines and standards by examining cancer and non-cancer health effects of the regulation, recreational benefits, and cost savings to publicly owned treatment works (POTWs) to which indirect-discharging CWT facilities send their ...
This document includes the following topics: Background; Data Collection; Scope/Applicability of the Proposed Regulation; Description of the Industry; Industry Subcategorization; Pollutants of Concern for the Centralized Waste Treatment Industry; Pollutants Selected for Regulation; Wastewater Treatment Technologies; Regulatory Options Considered and Selected for Basis of Regulation; Long-Term Averages, Variability Factors, and Limitations and Standards; Cost of Treatment Technologies; Pollutant Loading and Removal Estimates; Non-Water Quality Impacts; Implementation; Analytical Methods and Baseline Values; List of Definitions; List of Acronyms; Appendix A--Pollutant Groups; Appendix B--Listing of Characerization Data From Non-Hazardous Oils Facilities; Appendix C--Listing of Daily Influent and Effluent Measuements; Appendix D--Facility-Specific Compliance Costs; Appendix E--Attachements to Chapter 10; and Appendix F--Listing of Pollutants of Concern and Cas ...
Red mud is a by-product of bauxite processing through Bayer process. The amount of red mud generated depends largely on the type of ore used and the processing. Use of red mud as a catalyst can be a good alternative to the existing commercial catalysts. Its properties such as iron content in form of ferric oxide (Fe{sub 2}O{sub 3}), high surface area, sintering resistance, resistance to poisoning and low cost make it an attractive potential catalyst for many reactions. Besides red mud, ferric ion sludge from wastewater treatment plant has also been studied for its catalytic properties, mainly due to its ferric oxide constituent. This paper reviews the studies on red mud as a catalyst. The catalyst characteristics, reaction mechanisms involved and performance are examined and compared with iron oxide catalyst and commercial catalysts. (author)
A method of using fungi in removing heavy metal from wastewater was discussed. Fungi for this purpose can be obtained inexpensively, and on a constant basis from industrial fermentation processes. The biosorption of lead, cadmium and nickel on fungal stock cultures, was investigated. In these experiments, the fungal stock used was Aspergillus niger and Rhizopus stolonfier. Alkali pre-treatment of the fungal biomass improved the metal biosorptive capacity in comparison to live cells. The effect of alkali treatment, however, varied,showing highest biosorptive capacity for lead and least for nickel. Results showed that metal biosorption of metallic ions increased with an increase in pH from 3.2 to 4.0. Equilibrium times of five hours were observed for the biosorption of lead and cadmium, while the equilibrium time for nickel was three hours. 10 refs., 3 tabs., 7 figs.
The treatment of Be-contaminated wastewater has been paid little attention, although beryllium (Be) and its compounds are of high toxicity. In this research, aerobic granule was for the first time introduced to remove Be from aqueous solution. Influencing factors including reaction time, initial Be concentration, pH, biosorbent dosage, and coexistent metal ions (Cd, Cu, and Fe) were investigated in batch experiments. The aerobic granule, characterized by element analysis and CLSM, was abundant in carboxyl, phosphoryl, amine and hydroxyl groups. Potentiometric titration experiment demonstrated that the pH effect on biosorption depended on the surface charge of granule (pHzpc=2.4) and the species of Be (Be^2^+, Be(OH)^+, and Be(OH)2) in solution. The coexistent metal ions would either inhibi...
This paper describes a comprehensive model of wastewater treatment in secondary facultative ponds, which combines 3D hydrodynamics with a mechanistic water quality model. The hydrodynamics are based on the Navier-Stokes equation for incompressible fluids under shallow water and Boussinesq assumptions capturing the flow dynamics along length, breadth and depth of the pond. The water quality sub model is based on the Activated Sludge Model (ASM) concept, describing COD and nutrient removal as function of bacterial growth following Monod kinetics, except for Escherichia coli removal, which was modelled as first order decay. The model was implemented in the Delft3D software and was used to evaluate the effect of wind and the addition of baffles on the water flow pattern, temperature profiles i...
N-substituted aromatics are important priority pollutants entering the environment primarily through anthropogenic activities associated associated with the industrial production of dyes, explosives, pestides, and pharmaceuticals. Anaerobic treatment of wastewaters discharged by these industries could potentially be problematical as a result of the high toxicity of N-substituted aromatics. The objective of this study was to examine the structure-toxicity relationship of N-substituted aromatic compounds to acetoclastic methanogenic bacteria. The toxicity was assayed to serum flasks by measuring methane production in granular sludge. Unacclimated cultures were used to minimize the biotransformation of the toxic organic chemicals during the test. The nature and the degree of the aromatic substitution were observed to have a profound effect on the toxicity of the test compound. Nitroaromatic compounds were, on the average, over 500-fold more toxic than their ...
The operation of nuclear processing facilities and defense-related nuclear activities has resulted in contamination of near-surface and deep-subsurface sediments with both radionuclides and metals. The presence of mixed inorganic contaminants may result in undetectable microbial populations or microbial populations that are different from those present in uncontaminated sediments. To determine the impact of mixed radionuclide and metal contaminants on sediment microbial communities, we sampled a processing pond that was used from 1948 to 1975 for the disposal of radioactive and metal-contaminated wastewaters from laboratories and nuclear fuel fabrication facilities on the Hanford Site in Washington State. Because the Hanford Site is located in a semiarid environment with average rainfall of 159 mm/year, the pond dried and a settling basin remained after wastewater input into the pond ceased in 1975. This processing pond basin offered a unique ...
Biosorption using activated sludge biomass (ASB) as a potentially sustainable technology for the treatment of wastewater containing different metal ions (Cd(II), Pb(II) and Zn(II)) was investigated. ASB metal uptake clearly competed with protons consumed by microbial biomass compared with control tests with non-activated sludge biomass. Biosorption tests confirmed maximum exchange between metal ions and protons at pH 2.0-4.5. It was revealed by the study that the amount of metal ions released from the biomass increased with biomass sludge concentration. The result showed that maximum absorption of metal ions was observed for Cd(II) at pH 3.5, Pb(II) at pH 4.0, and pH 4.5 for Zn(II) ions. The maximum absorption capacities of ASB for Cd(II), Pb(II) and Zn(II) were determined to be 59.3, 68.5 and 86.5%, respectively. The biosorption of heavy metals was directly proportional to ASB stabilization corresponding to a reduction in heavy metals in the order of ...
The utilization of wood-shaving bottom ash (WBA) for the removal of Red Reactive 141 (RR141), an azo reactive dye, was investigated. WBA/H(2)O and WBA/H(2)SO(4) were made by treating WBA with water and 0.1M H(2)SO(4), respectively, to increase adsorption capacity. Adsorption of RR141 from reactive dye solution (RDS) and reactive dye wastewater (RDW) by WBA/H(2)O and WBA/H(2)SO(4) involved the BET surface area and pore size diameter. Properties of adsorbents, effect of contact time, initial pH of solution, dissolved metals and elution studies indicated that the decolorisation mechanism involved both chemical adsorption and precipitation with calcium ions. In addition, the WBA/H(2)SO(4) surface might contain sulphate-cation complexes that were specific to enhancing dye adsorption from RDW. The adsorption isotherm had a best fit by the Freundlich model. Freundlich parameters showed that WBA/H(2)O used more heterogeneous surface than WBA/H(2)SO(4) and activated carbon ...
Volatile organic compounds (VOC) are an important group of pollutants with adverse effects on humans and the environment. Primary air pollution abatement measures aim at prevention or reduction of pollutant production in industrial production processes, e.g. by improved processes but also by other methods (closed cycle processes, different process materials, etc.). If these measures have been implemented and emissions are still too high, an off-air purification unit must be installed. Biological purification is the method of choice for low pollutant concentrations. Biological purification processes are based on the activity of microorganisms which are capable of biochemical oxidation of organic and some inorganic gaseous compounds into non-polluting or non-odorous compounds. These processes have the advantage that they work at ambient conditions and therefore remove relatively low pollutant concentrations at low investment ...
Water is one of our most precious resources. However, for many in the United States, having fresh, safe drinking water is taken for granted, and due to this perceived lack of relevance, students may not fully appreciate the luxury of having safe running water--in the home. One approach to resolving water-quality issues in the United States may reside in providing education that presents accurate information in a meaningful way. Accordingly, this article describes a unit designed to emphasize the importance of water-quality testing and purification and to introduce students to local water-quality issues. The engineering-based module of this eighth-grade science activity is particularly important due to the design-build-test component. (Contains 5 figures.)
The presence of two major aminopeptidases (aminopeptidases I and II) in the giant alga Chara australis was shown using polyacrylamide gel electrophoresis. Partially purified aminopeptidase I had a molecular weight of about 120,000, hydrolyzed both leucine-?-naphthylamide (pH optimum 6.0) and alanine-?-naphthylamide (pH optimum 7.5), and was located both inside and outside the vacuole. Aminopeptidase I was inhibited by p-chloromercuribenzoic acid, iodoacetic acid, 1,10-phenanthroline, and N-tosyl-l-phenylalanine chloromethyl ketone. Aminopeptidase II hydrolyzed alanine-?-naphthylamide but not leucine-?-naphthylamide and was located only outside the vacuole.ImagesFig. 1Fig. 2Fig. 4Fig. 5
Mono- and disubstituted novel derivatives of the heptaene nystatin analog 28,29-didehydronystatin A1 (S44HP, 1) were obtained by chemical modification of the exocyclic C-16 carboxyl and/or an amino group of mycosamine moiety. The strategy of preparation of mono- and double-modified polyene macrolides was based on the use of intermediate hydrophobic N-Fmoc (9-fluorenylmethoxycarbonyl) derivatives that facilitated the procedures of isolation and purification of new compounds. The antifungal activity of the new derivatives was first tested in vitro against yeasts and filamentous fungi, allowing the selection of the most active compounds that were subsequently tested for acute toxicity in mice. 2-(N,N-dimethylamino)ethylamide of 1 (2) and 2-(N,N-dimethylamino)ethylamide of N-fructopyranosyl-28...
A fusion reactor (such as NET/ITER) which breeds its own tritium fuel requires tritium recovery, purification and separation from the other isotopes. Cyclic adsorption processes are strong candidates for several of the processes involved: amongst other advantages, they promise a low tritium inventory. A good adsorbent for such processes must have high adsorption capacity, high selectivity and very low tritium retention after each cycle. Pure zeolite powder is shown to have an excellent combination of these three properties. However, in practice problems can arise from tritium which is not removed by reactivation. In this paper we show that tritium retention in zeolites can be caused either by water retained in the zeolite structure, which can be removed by ore rigorous activation, or by water tapped on binders in commercial pellets. (orig.).
A simple method is presented for the separation of lead-203 from copper-backed thallium cyclotron targets. The procedure involves cation-exchange chromatography in hydrochloric acid and hydrochloric acid-acetone mixtures. Further purification involves anion-exchange chromatography in nitric acid-hydrobromic acid mixtures. A cation-exchange column containing 3.0 g of resin can handle as much as 15 g of thallium and 160 mg of copper. An anion-exchange column containing 3.0 g of resin can separate lead from up to 200 mg of thallium and 10 mg of copper. Separations are extremely sharp and less than 0.1 ..mu..g of thallium and less than 0.1 ..mu..g of copper remain in the lead-203 fraction.
A simple method is presented for the separation of lead-203 from copper-backed thallium cyclotron targets. The procedure involves cation-exchange chromatography in hydrochloric acid and hydrochloric acid-acetone mixtures. Further purification involves anion-exchange chromatography in nitric acid-hydrobromic acid mixtures. A cation-exchange column containing 3.0 g of resin can handle as much as 15 g of thallium and 160 mg of copper. An anion-exchange column containing 3.0 g of resin can separate lead from up to 200 mg of thallium and 10 mg of copper. Separations are extremely sharp and less than 0.1 #mu#g of thallium and less than 0.1 #mu#g of copper remain in the lead-203 fraction. (author).
Humic acids are considered problematically in drinking water because it can react readily with chlorine to form carcinogen compounds and its biological removal is much recommended. The scanning electron microscopy morphologies and optical parameters observed for natural humic acids (NHAs) extracted from different soils at Mitidja plain (Algeria) made them different from the commercial ones. Three of the most active strains of 19 actinomycetes were isolated and selected from surface soils at this plain. These strains were identified based on cultural characteristics and chemotaxonomic analysis and classified in the genus Streptomyces. Growth of these strains was assured on a poor liquid medium containing NHAs as carbon and nitrogen sources and degradation occur only in the presence of gluco...
Process residues are generated at both the Rocky Flats Plant (RFP) and the Savannah River Plant (SRP) during aqueous chemical and pyrochemical operations. Frequently, process operations will result in either impure products or produce residues sufficiently contaminated with transuranics to be nondiscardable as waste. Purification and recovery flowsheets for process residues have been developed to generate solutions compatible with subsequent Purex operations and either solid or liquid waste suitable for disposal. The ''scrub alloy'' and the ''anode heel alloy'' are examples of materials generated at RFP which have been processed at SRP using the developed recovery flowsheets. Examples of process residues being generated at SRP for which flowsheets are under development include LECO crucibles and alpha-contaminated hydraulic oil.
Summary of cyclotron production methods of "2"3"7Pu (45,2 d), "8"8Y (106,65 d) and "8"5Sr (64,84 d) tracers via nuclear reactions with protons and alphas on "2"3"5U, "8"8Sr and "8"5Rb targets in wide energy range is given. Chemical methods of separation and purification of the tracers from the irradiated uranium, strontium and rubidium targets are described. The tracers were used for determination of Pu (239-240), Sr-90 and Am-241 in the samples (soil, plants, underground waters) from Semipalatinsk Test Site. Obtained results are discussed.
Previous studies from this laboratory have shown that certain N-substituted phthalimides (NSPs) exhibit GA-like activity in a range of specific bioassays and that bioactive NSPs compete with ({sup 3}H)-GA{sub 4} for soluble binding sites in cucumber homogenates. As such, these compounds may prove useful in the purification and characterization of GA receptor proteins. To this end, five azido-NSPs have been synthesized and are currently being screened for biological activity and photochemical stability. Three azido-NSPs elicit {alpha}-amylase production in barley half-seeds and stimulate tissue elongation in d{sub 5} maize, lettuce, sunflower, and soybean. Further evaluations are in progress and these data as well as the utility of these compounds as photo-affinity ligands will be discussed.
Recent improvements in cell purification and transplantation techniques have contributed to the identification of cell populations known as tumor-initiating cells (TIC). This discovery has led to the -cancer stem cell hierarchy- concept, which holds that tumors are organized as a hierarchy of malignant tissues sustained by such TIC. However, this concept remains controversial. In this review, we examine recent advances in cancer stem cell research that have been generated from studies of Philadelphia (Ph) chromosome-positive leukemia. The abnormal Ph chromosome, which arises from a translocation creating the BCR-ABL1 fusion gene, is most commonly associated with chronic myelogenous leukemia (CML) and precursor B cell acute lymphoblastic leukemia (B-ALL). Examination of the pathophysiology ...
The development of 'Green Chemistry' requires new materials to replace the conventional organic chemistry by biological catalysts, to produce fine chemicals in an environmentally friendly manner. Microbial whole cells can be directly used as biocatalysts, providing a simple and cheap methodology since enzyme isolation and purification are avoided. High-density polyethylene (HDPE) is a very stable polymer though it can be activated by gamma radiation to induce grafting. Glycidyl methacrylate was grafted onto macroporous HDPE and PP in the range of 1-6%, proportional to the initial monomer concentration. Grafted polymers were further chemically modified with ethylenediamine to generate a cationic hydrogel of micron-size thickness onto the internal polymer surfaces. Modified polymers were able to immobilize Gram-positive and Gram-negative bacteria that can catalyze a chemical reaction as efficient as free cells do.
Extraction of 25 L fermentation broth of the newly isolated Streptomyces sp. strain TN58 and various separation and purification steps led to the isolation of five bioactive metabolites, namely brevianamide F (C1), reported from a streptomycete for the first time, N?-acetyltryptamine (C2), thiazolidomycin (C3), and two rhamnopyranosides (C4 and C5). These two rhamnopyranosides were produced directly, without precursor addition. The chemical structure of these five active compounds was established on the basis of 1H, 13C/APT and 2D NMR spectra, ESI and EI-MS data, and by comparison with data from the literature. According to the biological studies, we show in this work that the compounds C1, C2, C4 and C5 possess antimicrobial activities.
A Process for yellow cake production from local Euxenite was developed in Bench Scale by using sulphuric acid digestion with simultaneously ion-exchange and solvent extraction purification steps. Uranium was then precipitated as uranium diuranate by ammonia solution. Equipment used in this process includes : digestion vessels, columnar ion-exchange, solvent extraction and precipitation units Ore feed to the process could be adjusted up to 2 kilogram per day (8 hours operation) with yellow cake product purity meet the requirement of Usaec standard of about 10-50 gram per day. Included in this experiment are the leaching characteristics of the ore, the design and construction of continuous columnar 4-cycle ion exchange unit, determination of the extraction and stripping stages of a gravity flow mixer-settler and the design and construction of continuous yellow cake precipitation unit with large grain size and high density product
Forensic signatures are present in any Pu sample that can determine the sample`s origin: isotopic ratio of Pu, progeny species that grow into the sample, and contaminant species left over from incomplete purification of the Pu in fuel reprocessing. In the context of intelligence information, this can result in attribution of responsibility for the product of clandestine proliferant operations or material smuggled from existing stockpiles. A list of signature elements and what can be determined from them have been developed. Work needs to be done in converting concentrations of signature species into a quantitative forensic analysis, particularly in regard to reactor performance, but this should require only a small effort. A radiochemical analysis scheme has been developed for measuring these nuclides; more work is needed, particularly for determining fission product concentrations. A sample of Pu metal has been analyzed and several parameters determined that are ...
Corrosion behavior of deposition coated specimens prepared by the technique proposed by the authors is investigated in salt immersion tests, and also those of pure magnesium, 3N, 4N and 6N grades, and magnesium alloys, AZ31 and AZ91E, are investigated for comparison. Inhomogeneous corrosion occurs in AZ31 and AZ91E alloys when buffered solutions with pH values of 6.5 and 9.0 including 1% NaCl and a conventional 3% NaCl solution are used for immersion tests, while 6N-Mg shows homogeneous corrosion in such solutions. Corrosion behavior of the deposition coated specimen resembles that of 6N-Mg. Purification process included in the deposition coating technique provides homogeneity in microstructural and electrochemical terms, which results in improving corrosion resistance. (orig.)
The reference method used to analyse polychlorodibenzo-p-dioxins (PCDDs), polychlorodibenzofurans (PCDFs) and dioxin-like polychlorinated biphenyls (dl-PCBs) is chromatography with high resolution mass spectrometry (GC-HRMS). It is interesting to check the suitability of screening methods that are faster and less expensive. Different matrices (milk, fish oil, chicken compound feed, pork tissue, chicken tissue, sepiolitic clay, whole egg and herring tissue) were analysed in the frame of the European project DIFFERENCE1. One of the aims of this project is to optimise screening methods. The CALUX bio-assay was one of the screening techniques used. This paper presents the extraction and purification methods used for the analyses. The CALUX results for dioxins and for dl-PCBs were compared to the corresponding GC-HRMS results.
Functional properties of commercial and membrane processed pea protein isolates (PPI) prepared from yellow peas were investigated. Four protein isolates were prepared from yellow pea flour using water and KCl extractions at 25^oC followed by ultrafiltration and diafiltration (UF and DF) at pHs of 7.5 and 7.5 or 6 respectively. Following assessment of compositional attributes; solubility, foaming, flow and dynamic rheology, emulsification ability and heat-induced textural and rheological properties of prepared PPIs and a commercially available PPI were tested and compared. Membrane purification of proteins resulted in 28% to 68% reduction in phytic acid and enhanced, comparatively, the tested functional properties. Solubility of membrane processed PPIs, at all tested pHs, was superior and t...
A compilation of all universities, industrial and governmental agencies in Quebec which are actively involved in research and development of chemical products and industrial materials derived from biomass products, was presented. Each entry presented in a standard format that included a description of the major research activities of the university or agency, the principal technologies used in the research, available research and analytical equipment, a description of the research personnel, names, and addresses of contact persons for the agency or university. Thirty entries were presented. These covered a wide diversity of activities including biotechnological research such as genetic manipulations, bioconversion, fermentation, enzymatic hydrolysis and physico-chemical applications such as bleaching, de-inking, purification and synthesis. tabs.
Teleost gut associated lymphoid tissue (GALT) consists of leucocyte populations located both intraepithelially and in the lamina propria with no structural organization. The present study aims to assess different protocols for the isolation of GALT cells from an important fish species in the Mediterranean aquaculture, the gilthead seabream. Mechanical, chemical and enzymatic treatments were assayed. Nylon wool columns and continuous density gradients were used for further separation of cell subpopulations. Light microscopy and flow cytometry showed that the highest density band (HD) consisted of a homogeneous lymphocytic population, whereas the intermediate density band (ID) corresponded to epithelial and secretory cells and some lymphocytes. Respiratory burst activity of total cell suspen...
This is a report of extraction and identification of 1-O-alkyl glycerol present in the dried leaves of Bauhinia scandens. Fifty percent aqueous ethanolic extract of the plant at room temperature was fractionated over petroleum ether and diethyl ether. The diethyl ether soluble fraction showed positive bioactivity in Brine Shrimp bioassay. Isolation and purification of the active principle was subsequently done from diethyl ether fraction. The diethyl ether fraction was separated into acidic and neutral part. The acid free fraction was screened to be positive in Brine Shrimp bioassay. The NMR spectra (in CDCl3) indicated the probability of its lipoidal nature. The total lipid fraction was resolved into neutral, glyco, and phospho-lipids by column chromatography. Only the neutral fraction sh...
The aim of the present study is to identify and characterize the antimalrial agents from traitional Sudanese medicinal plants. 49 plants parts representing 26 species from 15 families were extracted and screened for their in vitro antimalrial activity using P. falciparum strain 3D7 which is chloroquine sensitive and Dd2 strain which is chloroquine resistant and pyrimethamine sensitive.The plant species investigated exhibited diverse botanical families. They includes Annonaceae, Aristolochiaceae, Asteraceae, Balantiaceae, Caesalpiniceae, Celasteraceae, Cucurbitaceae, Fabaceae, Graminae, Meliaceae, Myrtaceae, Polygonaceae, Rubiaceae, Rutaceae, and simaroubaceae. The evaluation of these plants for their antimalarial activity and their effect on lymphocyte proliferation was carried out. 57 extracts were tested on the chloroquine sensitive strain (3D7). Where 34 extracts (59%) exhibited significant activity against 3D7 with IC_5_0 values #100 #mu# g/ml), where as Sonochous cornatus, ...
The plerocercoid stage of the tapeworm Spirometra mansonoides produces a functional analog of human growth hormone (hGH). Among the similarities between plerocercoid growth factor (PGF) and hGH is competition for the same receptors on rabbit liver membranes. To take advantage of this characteristic in a purification scheme for PGF, rabbit liver microsomes were solubilized in Triton X-100 and the hGH receptors were purified over an hGH affinity column. The purified receptors from six rabbit livers were coupled to Affi-Gel-10 to create a receptor affinity column which was used to purify PGF. Chromatography of crude PGF over the receptor column resulted in a 1044 fold increase in specific activity. SDS-PAGE in the presence of 2-mercaptoethanol showed that the affinity-purified PGF contained three protein bands with apparent Mrs of 27.5 K, 22 K, and 16.7 K. Injections of the partially-purified PGF into hypophysectomized rats produced a dose-dependent growth response ...
About ten years ago microbiologically influenced corrosion manifested on stainless steel pipes used with river water for cooling a chemical plant. The pipe material was similar to Type 316 L. After only six weeks of operation pinhole leaks occurred nearly simultaneously at several welded joints of the pipe. The material degradation was simulated in laboratory and field corrosion tests. Microbiologically influenced corrosion failures also appeared on the pipes of a tubular heat exchanger of duplex steel Type 31803 and on carbon and stainless steel pipes in industrial waste water purification plants after these plants had been modernized with a biological purification unit. The basics of microbiologically influenced corrosion phenomena and typical corrosion failures of pipes will be described. (orig.) [German] Vor etwa zehn Jahren sind in einer neu errichteten chemischen Produktionsanlage an einer mit Flusswasser beaufschlagten Kuehlwasserleitung ...
A high-temperature flow reactor and different technical plants were tested within the framework of this research project. Anthropogenic N{sub 2}O emissions form during secondary flue gas or waste gas purification as secondary emissions during denitrification and pollution abatement measures. N{sub 2}O forms as an intermediate product as NO is reduced to N{sub 2}. Under certain operating conditions N{sub 2}O is not decomposed completely. Different secondary flue gas purification measures, i.e. selective noncatalytic reduction (SNCR), selective catalytic reduction (SCR), and nonselective catalytic reduction (NSCR) were investigated testing several technical plants and the high-temperature flow reactor. (orig./EF) [Deutsch] Das Forschungsprojekt ``Messung der N{sub 2}O-Emissionen von Verbrennungsanlagen und Untersuchung von Moeglichkeiten zur Emissionsminderung`` wurde an einem Hochtemperatur-Stroemungsreaktor und an verschiedenen technischen ...
High energy radiation was studied as a means for destroying hazardous organic chemical wastes. Tests were conducted at bench scale with a {sup 60}Co source, and at full scale (387 l/min) with a 1.5 MV electron beam source. Bench scale tests for both benzene and phenol included 32 permutations of water quality factors. For some water qualities, as much as 99.99% of benzene or 90% of phenol were removed by 775 krads of {sup 60}Co irradiation. Full scale testing for destruction of benzene in a simulated waste-water mix showed loss of 97% of benzene following an 800 krad dose and 88% following a 500 krad dose. At these loss rates, approximately 5 Mrad of electron beam irradiation is required to reduce concentrations from 100 g/l to drinking water quality (5 {mu}g/l). Since many waste streams are also inhabited by bacterial populations which may affect filtering operations, the effect of irradiation on those populations was also studied. {sup 60}Co and electron beam ...
Biosorption has been developed as an effective and economic method to treat wastewater containing low concentrations of metal pollutants. In this study, a bacterium, Citrobacter freudii, was used as a biosorbent to adsorb uranium ions. The thermodynamics and kinetics of this adsorption, as well as its mechanism, were investigated. The results indicated that the biosorption rate could be better described by a pseudo 2nd-order model than a pseudo 1st-order model. The adsorption of U (VI) proceeded very rapidly in the first 30 min and subsequently slowed down continuously for a long period. The biosorption isotherm of uranium by C. freudii could be described well by the Langmuir or Freundlich isotherm, and the latter was better. The thermodynamics parameters, {delta}H{sup o}, {delta}G{sup o}, and {delta}S{sup o} were calculated according to the results of the experiment, which showed this biosorption as being endothermic and spontaneous. The authors investigated the ...
Coal bed natural gas (CBNG) development in the Powder River (PR) Basin produces modestly saline, highly sodic wastewater. This study assessed impacts of wetting four textural groups (0-11%, 12-22%, 23 -33%, and > 33% clay (g clay/100 g soil) x 100%))with simulated PR or CBNG water on water retention. Soils received the following treatments with each water quality: a single wetting event, five wetting and drying events, or five wetting and drying events followed by leaching with salt-free water. Treated samples were then resaturated with the final treatment water and equilibrated to -10, -33, -100, -500, or -1,500 kPa. At all potentials, soil water retention increased significantly with increasing clay content. Drought-prone soils lost water-holding capacity between saturation and field capacity with repeated wetting and drying, whereas finer textured soils withstood this treatment better and had increased water-retention capacity at lower matric potentials.
Phosphorus sorption capacities of several different materials including Merribrook soil (a loamy sand) and some industrial solid wastes (red mud neutralized with gypsum, fly ash, bottom ash and black oxide) were determined in sorption isotherms by Langmuir and Freundlich equations. The materials were characterized by bulk density, particle density, total porosity and particle size distributions. Red mud gypsum possessed the best sorption capacity based on the Langmuir maxima. Alkaline fly ash and Merribrook soil had lower sorption maxima compared to the red mud gypsum. Bottom ash and acidic fly ash had very low sorption capacity at low concentrations. Merribrook soil had the highest hydraulic conductivity. The results suggested that alkaline fly ash may be a promising amendment for coarse sand bed to enhance phosphorus removal. Merribrook soil appears to be suitable for on-site wastewater treatment.
After the construction of its wastewater treatment plants, the City of Quebec began to implement overflow control in wet weather to ultimately meet the effluent discharge objectives, i.e. no more than two overflows per summer season in the St. Lawrence River and no more than four in the St-Charles River. After several years of studies to determine which management strategies would best suit the purpose, and to propose optimum solutions, a first project to implement optimal and predictive management in real time, called "Pilot", came to life in 1999. Construction in phases soon followed and the work was completed in the fall of 2009. As a result, requirements with regard to environmental rejects were met in two sectors, namely the St-Charles River and the Jacques-Cartier Beach, and aquatic recreational activities could resume. Meanwhile, the City also worked at giving back access to the water courses to the public by developing sites at the Jacques-Cartier Beach and ...
The objective of the Hanford Environmental Dose Reconstruction Project (HEDR) is to estimate the potential radiation doses received by people living within the sphere of influence of the Hanford Site. A potential critical pathway for human radiation exposure is through the consumption of waterfowl that frequent onsite waste-water ponds or through eating of fish, shellfish, and waterfowl that reside in/on the Columbia River and its tributaries downstream of the reactors. This document summarizes information on fish, shellfish, and waterfowl radiation contamination for samples collected by Hanford monitoring personnel and offsite agencies for the period 1945 to 1972. Specific information includes the types of organisms sampled, the kinds of tissues and organs analyzed, the sampling locations, and the radionuclides reported. Some tissue concentrations are also included. We anticipate that these yearly summaries will be helpful to individuals and organizations ...
The objective of the Hanford Environmental Dose Reconstruction Project (HEDR) is to estimate the potential radiation doses received by people living within the sphere of influence of the Hanford Site. A potential critical pathway for human radiation exposure is through the consumption of waterfowl that frequent onsite waste-water ponds or through eating of fish, shellfish, and waterfowl that reside in/on the Columbia River and its tributaries downstream of the reactors. This document summarizes information on fish, shellfish, and waterfowl radiation contamination for samples collected by Hanford monitoring personnel and offsite agencies for the period 1945 to 1972. Specific information includes the types of organisms sampled, the kinds of tissues and organs analyzed, the sampling locations, and the radionuclides reported. Some tissue concentrations are also included. We anticipate that these yearly summaries will be helpful to individuals and organizations ...
The objective of the Hanford Environmental Dose Reconstruction Project (HEDR) is to estimate the potential radiation doses received by people living within the sphere of influence of the Hanford Site. A potential critical pathway for human radiation exposure is through the consumption of waterfowl that frequent onsite waste-water ponds or through eating of fish, shellfish, and waterfowl that reside in/on the Columbia River and its tributaries downstream of the reactors. This document summarizes information on fish, shellfish, and waterfowl radiation contamination for samples collected by Hanford monitoring personnel and offsite agencies for the period 1945 to 1972. Specific information includes the types of organisms sampled, the kinds of tissues and organs analyzed, the sampling locations, and the radionuclides reported. Some tissue concentrations are also included. We anticipate that these yearly summaries will be helpful to individuals and organizations ...
A $200 million paper mill being built in Hagerstown, Md., is expected to produce 150,000 bone-dry short tons per year of de-inked, market-grade pulp for writing and printing paper. The 1st Urban Fibers facility, the largest capital project in Hagerstown's history, is slated for completion in the spring. Landegger Recycled Fiber Corp. will operate and maintain the 200,000-square-foot recycling mill and 60,000-square-foot water reclamation plant. The wastepaper recycling mill plans to minimize waste and pollution by: reclaiming 635 tons per day of 100 percent post-consumer mixed office waste from the solid waste stream; saving more than 16 million cubic feet of landfill area per year; conserving the fiber equivalent of 6,700 trees per day; using no chlorine; saving about 2,000 gallons of water and 4,000 kilowatt hours of electricity per ton of throughput, compared to virgin fiber mills; reusing treated wastewater, reducing effluent discharge by 65 percent; ...
We report the isolation of a new bacterium species (named as DN-06) that degrades pyridine, a model compound containing both carbon and nitrogen, from the aerobic activated sludge in a coking wastewater treatment plant. DN-06 was identified as Achromobacter sp. using 16S rDNA sequence analysis. In batch culture, more than 95% of pyridine (500?mg/L) was degraded within 18?h by DN-06 grown at 35?C and pH?8 with agitation at 170?rpm. Degradation experiments of pyridine at different initial concentrations (50?4,300?mg/L) revealed that pyridine was an inhibitory substrate, and that neither yield coefficient Y nor endogenous decay coefficient K d was a constant. The values of Y and K d were 0.55?0.74 and 0.0032?0.0057?h?1, respectively. Five kinetic models (Haldane, Yano, Aiba, Webb, and Monod) ...
In the first part of the symposium, experts reviewed the state of the art of decentralized waste water treatment in Europe. In the second part, exemplary solutions in Poland and the Czech Republic were presented. The final part was dedicated to future concepts and strategies. [German] Im Herbst letzten Jahres hat die Kommunale Umwelt-AktioN U.A.N. in einer Abfolge von drei Abwasserfachsymposien Expertenrunden zum Austausch ueber den aktuellen Stand des Wissens zum Thema dezentrale Abwasserbehandlung veranstaltet. Mit dem Internationalen Symposium 'Konzepte zur Abwasserbehandlung im laendlichen Raum Europas' in Celle hat das Projekt der U.A.N. seinen Abschluss gefunden. Der Konzeption des Projektes entsprechend haben im 1. Teil des Symposiums Experten ueber den Stand der Entwicklung auf dem Sektor der dezentralen Abwasserbehandlung in Deutschland berichtet. Im 2. Teil unserer Fachtagung wurden europaeische Beispiele fuer dezentrale Loesungen aus Polen und Tschechien ...
The objective this work was to evaluate the gamma radiation processing for elimination of organic contaminants on industrial wastewater. Standard samples with 17 hydrocarbons (acetophenone, anisole, benzene, chlorobenzene, cyclohexanone, N, N-dimethylaniline, phenol, naphtalene, 1-chloronaphtalene, n-octadecane, p-nitrotoluene, toluene, tetrachloroethane, tetramethylbenzene, n-undecane, m-xylene and o-xylene) was preparated in hexane with total concentration of 1 #mu# g/ #mu# l which was analyzed by gas chromatography. Other sample with the same concentration of these hydrocarbons in acetone was used to contaminate water samples, which were irradiated with gamma radiation from Co-60 between doses 5.0 to 20.0 KGy and dose rate of 1.162 KGy/h. The activity of source was 1470 Ci. Percents destruction of hydrocarbons were: 79.76 % to 5.0 KGy, 85.97 % to 7.5 KGy, 86.24 % to 10.0 KGy, 86.72 % to 12.5 KGy, 88.92 % to 15.0 KGy, 91.74 % to 17.5 KGy and 92.38 % to 20.0 KGy. ...
This project will determine whether electrolytic dialysis has promise in the separation of charged particles in an aqueous solution. The ability to selectively move ions from one aqueous solution to another through a semipermeable membrane will be studied as a function of emf, amperage, and particle electrical charge. The ions selected for the study are Cl{sup -} and SO{sub 4}{sup 2-}. These ions are of particular interest because of their electrical conduction properties in aqueous solution resulting with their association with the corrosive action of metals. The studies will be performed with commercial membranes on solutions prepared in the laboratory from reagent salts. pH adjustments will be made with dilute reagent acid and base. Specific objectives of the project include testing a selected membrane currently available for electrolytic dialysis, membrane resistance to extreme pH conditions, the effectiveness of separating a mixture of two ions selected on the basis of size, the ...
This paper reported on a study in which hydrogen was produced by fermentation of biomass. A continuous process using a non-sterile substrate with a readily available mixed microflora was used on heat treated digested sewage sludge from a wastewater treatment plant. Hydrogen was produced from waste sugar at a pH of 5.2 and a temperature of 37 degrees C. An experimental setup of three 5.5 L working volume continuously stirred tank reactors (CSTR) in different stirring speeds were constructed and operated at 7 different hydraulic retention times (HRTs) and different organic loading rates (OLR). Dissolved organic carbon was examined. The results showed that the stirring speed of 135 rpm had a beneficial effect on hydrogen fermentation. The best performance was obtained in 135 rpm and 8 h of HRT. The amount of gas varied with different OLRs, but could be stabilized on a high level. Methane was not detected when the HRT was less than 16 h. The study identified the ...
Industrial segments as plant of mining, hospitals and university generate considerable volumes of radioactive wastewater containing uranium. The increasing development of the use of the nuclear energy to lead away to an expansion of the sectors of the nuclear fuel cycle, but it leads to security problems and it appears the necessity of control of the removing of uranium and radioactive effluent treatments. Researches evaluate if the technique of the biosorption would promote an alternative process with attractive characteristics of cost-benefit. The residual biomass from agricultural activities has been studied and used as adsorbent of metals and organic composts by low cost, abundance and for being biodegradable. In this work, it is presented the efficiency of the coir pith for the adsorption of ions UO_2"2"+. The coir pith is a by-product of the harvest of the coconut, a renewable natural source. The study was accomplished using the batch techniques. The ...
One wonders how a facility will cope with the new Clean Air Act Amendments (CAAA). Environmental engineers working in large companies' facilities and in corporate engineering groups already have an idea of how to comply with the regulations for chemical plant equipment leaks. (In fact, the rules will also affect process bins, wastewater, transfer and storage.) But those who work for smaller companies or who have assignments not directly tied to environmental affairs may not have access to the latest thinking on compliance. One of the first challenges in becoming aware of the CAAA regulations is learning the new language, which consists of acronyms, some containing other acronyms. NESHAP, for example, stands for national emissions standards for hazardous air pollutants. Prior to the CAAA, NESHAPs applied to a few specific chemicals, such as benzene. Now the proposed rules establish a HON, a hazardous organic NESHAP. According to David Gustafson, environmental air ...
In 1990, field studies of water quality and stream macroinvertebrate communities were initiated in Sandia Canyon at Los Alamos National Laboratory. The studies were designed to establish baseline data and to determine the effects of routine discharges of industrial and sanitary waste. Water quality measurements were taken and aquatic macroinvertebrates sampled at three permanent stations within the canyon. Two of the three sample stations are located where the stream regularly receives industrial and sanitary waste effluents. These stations exhibited a low diversity of macroinvertebrates and slightly degraded water quality. The last sample station, located approximately 0.4 km (0.25 mi) downstream from the nearest wastewater outfall, appears to be in a zone of recovery where water quality parameters more closely resemble those found in natural streams in the Los Alamos area. A large increase in macroinvertebrate diversity was also observed at the third station. ...
The Process Waste Treatment Plant (PWTP) at the Oak Ridge National Laboratory is designed to remove radioactive contaminants, principally {sup 90}Sr, from process wastewater. Planned upgrades to the PWTP will use chabazite zeolite columns. Pilot-scale studies have shown that mass transfer zone lengths increase from 10 to about 30 cm as the superficial velocity increases from 5.5 to 22 cm/min. Calculations with a multicomponent equilibrium model showed that the distribution coefficient for strontium remains essentially constant over the process conditions, suggesting that a simple kinetic model (the Rosen long-bed solution) should adequately represent breakthrough behavior. Using a distribution coefficient of 4.87 L/g predicted by the equilibrium model, good agreement was found between experimental breakthrough curves and those calculated with the Rosen solution. This model allows prediction of bed depths and cycle times necessary to achieve the required ...
''S-220'' white oil is used currently to impregnate and fill high voltage cables for 110-500 kilovolts; it has high electrical characteristics and meets production and use standards. High pressure and cooling problems, however, require filling cables with lower viscosity oils, while insulation needs still demand high viscosity. The authors developed a new white oil similar to S-220 using a neutral oil made in producing sulfonate additives. The process involved vacuum distillation, low-temperature paraffination, sulfation with oleum, neutralizing with ammonium hydroxide and simultaneous extraction of sulfo-salts and contact purification. The lowest content of aromatic hydrocarbons was sought. Dielectric qualities varied with viscosity. Satisfactory thermooxidational capability was found at 50/sup 0/C with an oil of no less than 50 mm/sup 2//sec viscosity. The final white oil had no more than 2% aromatic hydrocarbons, thus assuring ...
Plerocercoids of the tapeworm Spirometra mansonoides produce a substance that stimulates growth of experimental hosts. We report purification of plerocercoid growth factor (PGF) to homogeneity by a process involving isolation and solubilization of plerocercoid membranes, isoelectric point selection by chromatofocusing chromatography or preparative isoelectric focusing, and anion-exchange chromatography. A radioreceptor assay (RRA) for human growth hormone (hGH) was used to detect PGF and purity of the 27.5-kDa protein was judged by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE). Proteolytic activity was detected in the 27.5-kDa protein by gelatin substrate PAGE. Characterization of PGF as a neutral cysteine proteinase was based on substrate and inhibitor specificities and dependence on pH and thiol-containing reagents. The association of hGH agonist and proteinase activities was shown by comparing RRA and hydrolytic activities in the presence ...
A method was developed to synthesize /sup 14/C-labelled n-alkanes for use in cigarette smoke studies. Specifically, n-(18-/sup 14/C)-octatriacontane was synthesized from 1 mCi (1-/sup 14/C)stearic acid in a radiochemical yield of 20%. The key features of this synthesis were two consecutive alkylations of tosylmethyl isocyanide followed by acid hydrolysis to (18-/sup 14/C)-19-octatriacontanone and modified Wolff-Kishner reduction to the n-alkane. After purification on silica gel 25 mg of (18-/sup 14/C)octatriacontane was obtained with a total radioactivity of 200 ..mu..Ci, a specific activity of 4.3 mCi/mmol, and a radiochemical purity in excess of 98% by thin layer radiochromatography. The method has also been applied to the synthesis of unlabeled n-pentatriacontane and is considered to be generally applicable to the synthesis of radiolabeled alkanes from radiolabeled fatty acids.
Adsorption of uranium onto various solids is important from purification, environmental, and radioactive waste disposal points of view. Adsorption of uranium on activated charcoal has been studied as a function of shaking time, amount of adsorbent, pH, concentration of adsorbate, and temperature. Uranium adsorption obeys the Langmuir isotherm. {Delta}H{degrees} and {Delta}S{degrees} were calculated from the slope and intercept of plots ln K{sub D} vs 1/T. The influence of different anions and cations on uranium adsorption has been examined. The adsorption of other metal ions on activated charcoal has been studied under specified conditions to check its selectivity; consequently, uranium was removed from Cs, Ba, Zn, and Co. More than 98% adsorbed uranium on activated charcoal can be recovered with 65 ml of 3 M HNO{sub 3} solution. A wavelength dispersive x-ray fluorescence spectrometer was used for measuring uranium concentration.
The operation of industrial facilities has generally resulted in contamination of the surrounding soils and ground water. A variety of methods have been proposed for the remediation of contaminated sites. This paper presents new process technology that is capable of performing treatment on ground water or soil washing leachates. The process is targeted to treat low levels of radioactivity, organics and heavy metals present in the aqueous solutions, to be easily transported and provide simple operation on-site and provide an effluent that meets the specified discharge quality. The purification process involves sequential chemical treatment and filtration. The paper will describe the development of the technology and review the current progress in its use to remediate contaminated sites at Chalk River. The application of the process technology has demonstrated that the ambitious goal of setting the effluent targets to meet the drinking water standards was realized. A ...
The operation of industrial facilities has generally resulted in contamination of the surrounding soils and ground water. A variety of methods have been proposed for the remediation of contaminated sites. This paper presents new process technology that is capable of performing treatment on ground water or soil washing leachates. The process is targeted to treat low levels of radioactivity, organics and heavy metals present in the aqueous solutions, to be easily transported and provide simple operation on-site and provide an effluent that meets the specified discharge quality. The purification process involves sequential chemical treatment and filtration. The paper will describe the development of the technology and review the current progress in its use to remediate contaminated sites at Chalk River. The application of the process technology has demonstrated that the ambitious goal of setting the effluent targets to meet the drinking water standards was realized. A ...
Glycosaminoglycans synthesized by cultured rabbit smooth muscle cells were isolated after incorporation of (/sup 3/H)-glucosamine into glycosaminoglycans in the presence or absence of 10% fetal bovine serum. Glycosaminoglycans were quantitated by two-dimensional electrophoresis after proteolytic digestion of the cell layers and media. The results show that the presence of serum has no effect on the chondroitin sulfate, heparan sulfate and dermatan sulfate content of the cell layers. The incorporation of (/sup 3/H)-glucosamine into hyaluronic acid of the cell layers was three times higher in the presence of serum. In the medium , the quantity of hyaluronic was two times higher in the presence of serum while the other glycosaminoglycans remained unchanged. The incorporation of (/sup 3/H)-glucosamine into hyaluronic acid was unaffected by the presence of serum. Specific proteoglycans were isolated from medium after with (/sup 35/S)-sulfate and (/sup 3/H)-serine by isopycnic ...
Four extracellular keratinases (designated KI, KII, KIII, and KIV) were produced during submerged aerobic cultivation in a medium containing native human foot skin (NHFS) for enzyme synthesis. The molecular weights, determined by SDS-PAGE, were 25, 50, 34, and 19kDa, respectively. Gel filtration of the four purified enzymes in native conditions indicated that active keratinase KI is a novel homo-octamer, KII a homo-dimer, and KIII and KIV monomers. All four keratinases exhibited high activities at pH 8.0-10.0 with an optimal pH of 9.0. The optimal temperature for keratinolytic activity of KI, KII, and KIII was approximately 50, and 60degreeC for KIV. One millimolar of PMSF completely inhibited the keratinolytic activities of the four enzymes. The N-terminal sequences of KI, KII, and KIII s...
The ruthenium decontamination factor in Purex process falls quickly in successive TBP cycles. So, it is necessary to change the chemical states of RuNO complexes in order to improve DF_R_u in the uranium purification cycle. Hydrazine nitrate is being used to transform RuNO complexes into in-extractable Ru(III)and Ru(IV). However, hydrazine nitrate may be inverted into hydrazoic acid which is dangerous and can bring an unstable factor. Pretreatment using U(IV) solution provides another method to improve the decontamination of ruthenium in Purex process. 0.02 mol/lU(IV) solution can transform RuNO complexes into inextricable species by heating in water bath. The D_R_u can be decreased by a factor of 10-20. U(IV) pretreatment does not bring any harmful chemical in process. The acidity has a very large influence on the effect of pretreatment. The higher the acidity is, the worse the effect will be.
As part of our program in radiopharmaceutical chemistry we have prepared and evaluated a series of radioiodinated 1-alkyl-4-phenylpiperazines as potential brain-imaging agents. The compounds were chosen on the basis of their synthetic versatility, activation toward electrophilic substitution, and ease of purification. The intermediates 1-6 were readily obtained and converted to the corresponding radioiodinated products 7-12 in 76-91% isolated radiochemical yields. The tissue distribution in rats indicated that the 1-N-butyl derivative 9 possesses the best combination of brain uptake (0.28-0.35% ID X kg/g), retention, and selectivity (brain/blood greater than 20) over the 4-h evaluation period. A subsequent imaging and tissue distribution study in the dog using 131I-labeled 9 supported the results observed in the rat and suggested the potential of this agent as a brain-imaging agent.
Gallium is present in surplus weapons-grade plutonium (WG-Pu) at a concentration of approximately 1 wt %. Plans are to dispose of surplus WG-Pu by converting it to UO{sub 2}-PuO{sub 2} mixed oxide (MOX) fuel and irradiating it in commercial power reactors. However, the presence of high concentrations of gallium in plutonium poses a potential corrosion problem during the process of MOX fuel irradiation. The batch experiments performed in this study were designed to measure the capability of the PUREX solvent extraction process to separate gallium from plutonium under idealized conditions. Radioactive tracing of the gallium with {sup 72}Ga enabled the accurate measurement of low concentrations of extractable gallium. The experiments approximated the proposed flowsheet for WG-Pu purification, except that only one stage was used for each process: extraction, scrubbing, and stripping. The gallium decontamination factor (DF) obtained after one extraction stage was about ...
The ruthenium decontamination factor in Purex process falls quickly with recycles of TBP. So it is necessary to change the chemical states of RuNO complexes in order to improve DF_R_u in the uranium purification cycle. The retention of RuNO complexes in TBP-kerosenelaurohydroxamic acid is observed to be quite large in our previous work. Therefore, water-soluble short chain hydroxamic acid is used as complexing agent to decrease the distribution coefficient of Ru. Hydroxamic acid can transform RuNO complexes into in-extractable species by TBP-kerosene in certain conditions. The result of cascade experiment indicates that the ruthenium decontamination can be increased by a factor of 40-50. Acidity has more influence on the effect of pretreatment. The higher acidity is, the worse the effect will be. The pretreatment is first carried out in low acidic solution, then extractive acidity is increased. In this way, the distribution of Ru can be decreased obviously. After ...
Functionalization of carbon nanotubes is very challenging for their applications. The paper here describes a new method to functionalize multi-walled carbon nanotubes (MWCNTs) as specific affinity adsorbents. MWCNTs were acid purified and pretreated with (3-aminopropyl)-triethoxysilane (APTES) in order to introduce abundant amino groups on the surface of MWCNTs. After the conversion of amino groups to carboxyl groups by succinic acid anhydride, MWCNTs were attached to protein A or aminodextran using 1-ethyl-3,3' (dimethylamion)-propylcarbodiimide as a biofunctional crosslinker. The incorporation of aminodextran as a spacer arm noticeably increased the binding capacity of the APTES-modified MWCNTs for protein A. The application of affinity MWCNTs for purification of immunoglobulin G was then evaluated. The affinity of MWCNTs with AMD spacer exhibited a high adsorption capacity of {approx}361 {mu}g IgG/mg MWCNT (wet basis). About 75% of bound IgG was eluted ...
The size of the market for pulverized activated charcoal and particulate activated charcoal prepared by the Association of Inorganic Chemicals of Japan is 55,000t/y (1987) in total. Individually, some fields showed the expansion such as water purification, water treatment and gas treatment on the one hand, but on the other hand, several fields showed the decline such as sugar refining, dextrin sugar and soda glutamate. As a whole, the market showed no marked fluctuations or a very slight increase. Many of the above usages are traditional in the chemical industry and the food industry, etc., and the new usages developed in the past several years have not grown to influence the statistics as yet. Selection of raw material is the key for determining the character of activated charcoal. And the factors of determining the characteristic features are fine pore, surface area and surface activity (catalystic activity). Furthermore, the function requirement from the ...
To reduce the volume of radioactive wastes after evaporation, activity carriers can be separated from the inactive salt load. Boric acid separation from PWR concentrates was considered a preliminary stage for nuclide precipitation. In connection with the precipitation process, the reaction conditions for boric acid separation were determined by bench-scale experiments. After evaluating the known purification processes, crystallization was suggested as a practicable method. After inactive bench-scale experiments, mixed crystal formation with iron hexacyanoferrate for Cs removal was chosen. The disturbing effect of the complexing agents was neutralized by a pre-dose of iron-III-salts. By specifying the precipitation conditions, for Cs-134 an activity separation from 3,0 E + 06 Bg/l to 1,9 E + 02 Bg/l, and for Cs-137 from 5,9 E + 06 Bg/l to 1,2 E + 02 Bg/l was achieved. Accordingly, the decontamination factor for Cs-134 was 16000, and for Cs-137 48000. For the ...
A new method for the determination of {sup 237}Np and Pu isotopes in large soil samples has been developed that provides enhanced uranium removal to facilitate assay by inductively coupled plasma mass spectrometry (ICP-MS). This method allows rapid preconcentration and separation of plutonium and neptunium in large soil samples for the measurement of {sup 237}Np and Pu isotopes by ICP-MS. {sup 238}U can interfere with {sup 239}Pu measurement by ICP-MS as {sup 238}UH{sup +} mass overlap and {sup 237}Np via {sup 238}U peak tailing. The method provides enhanced removal of uranium by separating Pu and Np initially on TEVA Resin, then transferring Pu to DGA resin for additional purification. The decontamination factor for removal of uranium from plutonium for this method is greater than 1 x 10{sup 6}. Alpha spectrometry can also be applied so that the shorter-lived {sup 238}Pu isotope can be measured successfully. {sup 239}Pu, {sup 242}Pu and {sup 237}Np were measured ...
Studies have been conducted to determine the feasibility of using collisional cooling for reducing emittances and energy spreads in negative-ion beams to levels commensurate with effective isobaric purification with conventional high-resolution electromagnetic isobar separators as required for use at the Holifield Radioactive Ion Beam Facility (HRIBF). We have designed a gas-filled radio frequency quadrupole ion cooler equipped with provisions for retarding energetic negative-ion beams to energies below thresholds for electron detachment at injection and for re-acceleration to initial energies after the cooling process. The device has been used to cool several ion beams with initial energy spreads, {delta}E>10 eV to final energy spreads, {delta}E{approx}2 eV FWHM, including O{sup -} and F{sup -}. Overall transmission efficiencies of {approx}14% for F{sup -} beams have been obtained. Experimental results show that electron detachment is the major loss ...
The population masses in many coastal zones in Japan, and human activities are greatly effected. The representative water area is the Tokyo Bay. The population of the Tokyo Bay reaches 26 million at present, and a mass of organic substance and nutrient salt flow into it through rivers and sewage-treatment plants, etc. With the improvement of pollution source countermeasure and sewerage in the area, the inflow load to the Bay gradually decreases, but in the inner bay, red tide is generating in the summertime mainly. And, the anoxic water areas observed in bottom layer in summertime make large effects on the seafood. It is a large theme to clarify formation process of the anoxic water area and to solve this problem for the Tokyo Bay in the twenty-first century. In this paper, changes in water qualities and human activities and fundamental approach of water quality conservation of the Tokyo Bay are described. As maintenance and regeneration countermeasures of the water quality in the ...
Accelerated oxidation treatment technology is introduced for use in the treatment of poor quality water by ozone injected from the bottom of a pressurized ozone contact tank. Under study as oxidation accelerating processes using ozone center about an ozone/hydrogen peroxide treatment, ozone/UV treatment, ozone/hydrogen peroxide/UV treatment, etc. As the result of testing, important respects in accelerated oxidation are learned, which are stated below. In the ozone-aided treatment, there are some substances, such as chromatic matters, that can be removed more rapidly when in direct contact with gaseous ozone. In this case, the concentration of remnant ozone poses an important problem. In relation to the amount of injected hydrogen peroxide, what is important is the ozone/hydrogen peroxide injection ratio relative to the substance that is to be removed. In the use of UV rays, since the decomposition rate of dissolved ozone is approximately ten times higher than that of hydrogen peroxide, ...
The activated charcoal treatment in the field of the water treatment is applied to water supply, sewage, industrial water supply and industrial sewage, etc.. Its main treatment effects are (1) decolorization, (2) removal of odorous substance, (3) removal of organic material which is detected as COD or BOD, (4) removal of harmful substance, (5) removal of substance which could generate muddness and tarnish and (6) removal of organic material which affects the succeeding high degree treatment badly, etc.. Many actual application examples in the above fields have been reported. As the most recent topic, a big amount of the demand of activated charcoal is expected in the treatment of water supply. Chlorine which is used as disinfectant during the water purification process generates organic halogen compounds such as trihalomethane through the reaction with precursor such as humic acid. The countermeasure therefore is being developed in the direction of removing the ...
Since the beginning of the large-scale technical manufacture of activated charcoal at the start of the century, this product has become increasingly important. Activated charcoal is a central part today of many chemical industrial processes. Furthermore, the purification of exhaust air and liquid wastes is often based on the adsorption by activated charcoal. The constantly increasing hygienic demands made of our drinking water may also often only be fulfilled by using activated charcoal. The highly developed adsorption technique of today is considerably supported by continuous improved quality of the products which can only be achieved by progress in manufacturing techniques. The large-scale use of activated charcoal has only become possible for a series of tasks by developing suitable reactivation methods. The last German-language monograph on activated charcoal appeared 18 years ago. The present work wishes to close this gap and in particular to give a survey on ...
This paper presents some basic elements regarding the domain of the collaborative systems, a domain of maximum actuality and also the multiagent systems, developed as a result of a sound study on the one-agent systems.
In the third quarterly report adsorption of heavy metals ions such as Cu(II) and Cr(VI) onto soils drawn from the laboratory-type wetland was shown to be weak. Secondly, it was shown that modified-clays did adsorb Cr(VI) ions strongly at pH 4.5. Further, studies on the pH dependence of the adsorption of {beta}-naphthoic acid, (NA), a well-documented contaminant in many oil and gas well waste waters onto modified-clays were undertaken and it was shown that uptake of NA by modified-clays was of the high affinity type at pH 4.5 and 7.0, but weak at pH 9.0. Adsorption of heavy metal ions, Cu{sup 2+}, and Cr(VI) onto algae, a proposed wetland amendment, was carried out and the results were presented and discussed in the fourth quarterly report. Uptake of NA by the soil component of the laboratory-type wetland was monitored as a function of pH. This quarterly report presents results from studies on the uptake of phenol and {beta}-naphthoic acid by laboratory-type wetlands designed and built ...
Recent central processing of domestic wastewater in Malaysia has initiated investigations into the disposal/utilization of the sewage sludge produced. We had conducted an experiment to investigate the feasibility of using dewatered sewage sludge and coconut coir as a peat substitute in a potting medium for chrysanthemum. The experiment involved 9 treatments with sewage sludge (SS) and coconut coir (CC) mixed in different ratios (v/v) to replace peat in the standard potting medium of 3:2:1 (soil: peat: sand).The potting medium contained the following treatments, T1: peat + recommended rates of Agroblend (Ag), a slow release fertilizer, and Grofas (Gf), a foliar fertilizer (commonly used medium and fertilization), T2: [1SS:1CC] + Ag, T3: [1SS:1CC] + half recommended rates of Agroblend and Grofas (1/2Ag + 1/2Gf), T4: [2SS:1CC] + Ag, T5: [2SS:1CC] + 1/2Ag + 1/2Gf, T6: [3SS:1CC] + Ag, T7: [3SS:1CC] + 1/2Ag + 1/2Gf, T8: [4SS:1CC] + Ag, and T9: [4SS:1CC] + 1/2Ag + 1/2Gf; ...
The performance of anaerobic biological process is heavily process conditions dependent. In this study, an attempt has been made to investigate the influence of process conditions like temperature, sludge age and hydraulic retention time (HRT) on the efficiency of an upflow anaerobic sludge blanket (UASB) reactor and upflow anaerobic sludge filter (UASF) to treat combined industrial wastewater. Reactors were operated at easing ambient temperatures (38, 30, 20 and 14 deg. C) and correspondingly increasing sludge ages (60, 90, 120 and 150 days). At temperature 38 deg. C and sludge age of 60 days, UASF showed better performance than VASE reactor. This mainly due to the enhanced filtration through well-graded sand filter and fairly good biological activity in UASF. At this stage, lack of sludge granulation in VASE reactor resulted in poor biological activity; hence, relatively poor performance. At temperatures 30 and 20 deg. C with sludge ages of 90 and 120 days, ...
An approach of acidification was examined on formation of hydrogen-producing granules and biofilms in upflow column-shaped reactors. The reactors were fed with synthetic glucose wastewater and operated at 37 C and pH 5.5. The acclimated anaerobic culture was inoculated in four reactors designated R1, R2, R3 and R4, with R3 and R4 filled with granular activated carbon as support medium. To unveil the roles of acidification, microbial culture in R2 and R3 was subject to an acid incubation for 24 h by shifting the culture pH from 5.5 to 2.0. The experimental results suggested that the acidification substantially accelerated microbial granulation, but not biofilm formation. Microbial activities were inhibited by the acid incubation for about 78 h, resulting in the retarded formation of biofilms of the acidified culture. Reducing culture pH resulted in improvement in cell surface physicochemical properties favoring microbial adhesion and immobilization. Zeta potential ...
Hexavalent Cr has been identified as one of the toxic metals commonly present in industrial effluents. Among the treatment techniques developed for removing Cr(VI) from waste waters, sorption is most commonly applied, due to its simplicity and efficiency. However, few adsorbents can be recycled and reused cost-effectively. In this study, the removal and recovery of Cr(VI) from water using Li/Al LDH was investigated. The removal of Cr(VI) by Li/Al LDH was evaluated in a batch mode. The results demonstrated that Cr(VI) adsorption onto Li/Al LDH occurs by replacing the Cl{sup -} that originally exists in the interlayer of the adsorbent. The degree of Cr(VI) adsorption observed for Li/Al LDH was relatively high and the process occurred rapidly; however, a portion of adsorbed Cr(VI) was gradually desorbed, due to the Li de-intercalation of Li/Al LDH. Lithium de-intercalation from Li/Al LDH with interlayer Cl{sup -} and interlayer Cr(VI) follows the first order kinetics and has the ...
Except nuclear industry, diverse structures (hospitals, of research or manufacturers) can have appeal to the use of radioisotopes conditioned under unsealed shape. Such practices lead to tolerate releases in environment in the respect of a statutory device. So the collective network can contain radioisotopes the future of which is going to depend partially on the cleaning applied to waste water. This study through the analysis of a concrete case, has for objective to inform about the future of gamma radioelements present in waste water treated by a wastewater treatment plant. The contamination of the network is essentially due to Tc{sup 99} and I{sup 131}, radioelements present whatever the working day and the hour considered. The total estimated in-load for a day is important, of the order of 4000 MBq for Tc{sup 99} and 15 to 300 MBq for I{sup 131}. The assessment of cleaning of the station shows that this one plays a role towards this pollution through these ...
The K site near Seoul began landfilling in 1992. The landfilled wastes include municipal solid waste (66.4%), construction residues (20.4%), water and wastewater sludges (trace levels), and hazardous waste (trace levels). The water content of the municipal solid waste is very high (47.3%); as a result, the leachate level (average E.L.) of the landfill, the design value of which is 7.0 m, was measured at 10.3 m in January 1995 and is increasing. The increase of leachate level in the landfill site causes a problem with slope stability. The leachate level at each disposal stage divided by the intermediate cover layer was calculated with the HELP (Hydrologic Evaluation of Landfill Performance) model and calibrated with the data measured from February 1993 to June 1995. Also, the hydraulic conductivities of the waste layer and the intermediate cover layer in each stage were calibrated continuously with HELP model analysis. To verify these results, the total water ...
The Outstanding Achievement Award in Water Pollution Control' is intended to recognize the water pollution control program that best demonstrates achieving significant, lasting, and measurable excellence in water-quality improvement in preventing water-quality degradation in a region, basin, or water body. This article is about the 1991 Award. This year, WPCF honored Los Angeles Hyperion Treatment Plant with a citation of outstanding achievement. To qualify for this honor, Hyperion has remarkably improved the quality of wastewater discharged to Santa Monica Bay since 1985. Capital programs developed by Los Angeles to achieve this rapid improvement, coined the Hyperion Improvement Program (HIP), reflect the city's commitment to protect the valuable resource of Santa Monica Bay. The HIP was conceived in 1986 to cease sludge ocean disposal by the end of 1987 and expedite effluent quality improvement before 1991, when the full secondary expansion is ...
The economic feasibility of using granular activated carbon (GAC) to remove organic contaminants from industrial and municipal wastewater is contingent upon its reuse during multiple adsorption-regeneration cycles. The most common process for the regeneration of GAC is the thermal method. Drawbacks associated with thermal regeneration include a 5--10% loss of carbon due to oxidation and attrition, a decrease in adsorption capacity, and high energy costs. The purpose of this study was to investigate the regeneration of GAC using hydrothermal technology. Phenol contaminated and non-contaminated GAC samples were regenerated using supercritical water (411 deg C and 26.2 MPa) with dissolved oxygen concentrations of 0 mg/L, 5 mg/L, and 100 mg/L. For comparative purposes, GAC was regenerated using subcritical water (300 deg C and 12.4 MPa) with a dissolved oxygen concentration of 5 mg/L. Regenerated GAC samples were evaluated in terms of adsorption capacity, BET surface ...
Carbonyl compounds constitute an important reactive class of non methane volatile organic compounds. They can be emitted directly to the atmosphere from primary sources such as combustion engines, landfills and wastewater surfaces or as secondary products by the photochemical oxidation of hydrocarbons and other volatile organic compounds 1-3. Carbonyls photo-oxidize during the day to produce toxic radicals such as OH, HO_2, RO and RO_2. These species react with nitrogen oxides (NOx) and other VOCs present in the atmosphere to form tropospheric ozone (O_3); a highly reactive oxidizing agent that is harmful to human health, agricultural products and climate 4, 5. Hence identifying the levels and sources of ozone precursors such as low carbonyls, carbon monoxide (CO) and NOx derivatives, and understanding their physical and chemical transformation in the troposphere is an important task due to their atmospheric and adverse health implications. Diurnal variations of ...
The Department of Energy (DOE) Subsurface Contamination Focus Area (SCFA) sponsored a technology demonstration of non-traditional in situ vitrification (NTISV) at Los Alamos National Laboratory (LANL). The project team for this demonstration included MSE Technology Applications, Inc., Geosafe Corporation, and LANL. The technology demonstration involved the performance of two large-scale test melts. The first, referred to as the ''cold'' test, was performed on a simulated absorption bed that contained surrogate contaminants. The cold test was conducted in April 1999. The second demonstration, referred to as the ''hot'' test, took place at LANL's Material Disposal Area (MDA) V in April 2000. The hot test was conducted on a portion of an absorption bed that received radionuclide and metal-contaminated wastewater from a laundry facility and a research laboratory from the mid-1940s to the ...
The complexity and diversity of the microbial communities in biogranules from an upflow anaerobic sludge blanket (UASB) bioreactor were determined in response to short-term changes in substrate feeds. The reactor was fed simulated brewery wastewater (SBWW) (70% ethanol, 15% acetate, 15% propionate) for 1.5 months (phase 1), acetate / sulfate for 2 months (phase 2), acetate-alone for 3 months (phase 3), and then a return to SBWW for 2 months (phase 4). Performance of the reactor remained relatively stable throughout the experiment as shown by COD removal and gas production. 16S rDNA, methanogen-associated mcrA and sulfate reducer-associated dsrAB genes were PCR amplified, then cloned and sequenced. Sequence analysis of 16S clone libraries showed a relatively simple community composed mainly of the methanogenic Archaea (Methanobacterium and Methanosaeta), members of the Green Non-Sulfur (Chloroflexi) group of Bacteria, followed by fewer numbers of Syntrophobacter, ...
Sorption studies of cesium, strontium, and cobalt (Cs, Sr, and Co) on bentonite under various experimental conditions, such as contact time, pH, sorbent and sorbate concentration, and temperature, have been performed. The sorption data for all these metals have been interpreted in terms of Freundlich, Langmuir, and Dubinin-Radushkevich equations. Thermodynamics parameters, such as heat of sorption {Delta}H{degrees}, free energy change {Delta}G{degrees}, and entropy change {Delta}S{degrees}, for the sorption of these metals on bentonite have been calculated. The value of {Delta}H{degrees} shows that the sorption of Cs was exothermic, while the sorption of Sr and Co on bentonite were endothermic in nature. The value of {Delta}G{degrees} for their sorption was negative, showing the spontaneity of the process. The maximum loading capacity of Cs, Sr, and Co were 75.5, 22, and 27.5 meq, respectively, for 100 g of bentonite. The mean free energy E of Cs, Sr, and Co sorption on bentonite was ...
Biosorption is presented as an alternative choice to traditional physicochemical means for removing toxic metals from groundwater and wastewaters. Removal of lead (Pb) from solutions was studied using Escherichia coli (parental) and Vitreoscilla hemoglobin (VHb)-expressing E. coli (transformed) cells. Pb biosorption was increased in bacterial hemoglobin-expressing E. coli cells grown in Luria broth B containing different concentrations of Pb{sup 2+}. The maximum Pb{sup 2+} biosorption of transformed and parental cells was determined to be 612 and 370 {mu}g Pb/g biomass, respectively. The inhibitory effect of Pb{sup 2+} on the parental strain was determined at 10 ppm. However, in transformed cells, Pb{sup 2+} was lethal at 100 ppm. The optimum aeration required for the transformed cells was lower than that for the parental strain on a growth yield basis. A linear correlation was established between the biosorption and uptake amounts. The biosorption process was ...
Biosorption of heavy metals by various biological materials has been studied extensively in the last decade due to its potential particularly in wastewater treatment. The presence of a large number of metals in industrial metal-bearing solutions makes it necessary to investigate their effect on the final metal uptake by individual biosorbent materials. Nonliving biomass of Sargassum, a brown marine alga, is capable of binding more than 10% of its dry weight in toxic cadmium ions. Although ubiquitous iron interferes with Cd uptake, only approximately 4.5% of it is sequestered (biomass dry weight). Biosorption of both metals at pH 4.5 could be described by Langmuir-type isotherms with b, the affinity-related coefficient (Cd: b = 0.015; Fe: b = 0.027). The interference of Fe with Cd uptake, and vice versa, was assessed by deriving three-dimensional equilibrium two-metal sorption isotherm surfaces, smoothed and cut to reveal the inhibition effect of Fe on biosorption ...
TRITEX was a pumped loop with Pb-15.8Li, fabricated from steel 1.4922. In contact with the molten eutectic were also molybdenum, vanadium and armco-iron. The loop was originally designed to investigate tritium extraction using solid getter metals. Over the years the goal changed to the study of metals, corrosion products and purification of the eutectic mixture. Therefore many modifications were done. The first part of this report describes TRITEX. All parts were enclosed in thermoboxes for a homogeneous temperature. One test section was in an argon glove box and could be opened during operation. Other special equipment`s were: permeation membranes and liquid-metal-covergas-interfaces to study the transport of H{sub 2}, D{sub 2} and {sup 3}H, different purification devices, a quartz observation window to see the liquid metal surface, 4 different kinds of flow measurements, level indicators, freeze valves. The second part describes loop ...
An outline of the instrumentation and control systems associated with fuelling machines is given. The control systems such as hydraulic system, oil hydraulic system, electric control system and the remote control systems have been discussed in detail. The difference between RAPP and MAPP fuel handling control systems has been explained. A computer based system for the Narora fuel handling control system is also discussed. (S.K.K.).
Objectives: The purpose of this work was to study the genetic determinants responsible for extended-spectrum beta-lactamase (ESBL) resistance of Salmonella isolated from Dutch poultry, poultry meat and hospitalized humans. Methods: Thirty-four ESBL-resistant Salmonella isolates from The Netherlands were tested towards 21 antimicrobial agents. PCR and sequencing were used to determine the underlying genetic determinants responsible for the ESBL phenotypes. The transferability of the ESBL phenotypes was tested by conjugation to a susceptible Salmonella enterica serovar Dublin and plasmid purification, restriction fragment length polymorphism (RFLP) and pulsed-field gel electrophoresis (PFGE) were employed to further characterize a subset of the isolates. Results: A great genetic diversity was seen among the isolates. The bla(TEM-52) gene was most predominant and was found among Salmonella enterica serovars Blockley, Thomson, London, Enteritidis phage type 14b, ...
["3H]Indole-3-acetyl-myo-inositol was hydrolyzed by buffered extracts of acetone powders prepared from 4 day shoots of dark grown Zea mays L. seedlings. The hydrolytic activity was proportional to the amount of extract added and was linear for up to 6 hours at 37"0C. Boiled or alcohol denatured extracts were inactive. Analysis of reaction mixtures by high performance liquid chromatography demonstrated that not all isomers of indole-3-acetyl-myo-inositol were hydrolyzed at the same rate. Buffered extracts of acetone powders were prepared from coleoptiles and mesocotyls. The rates of hydrolysis observed with coleoptile extracts were greater than those observed with mesocotyl extracts. Active extracts also catalyzed the hydrolysis of esterase substrates such as #alpha#-naphthyl acetate and the methyl esters of indoleacetic acid and naphthyleneacetic acid. Attempts to purify the indole-3-acetyl-myo-inositol hydrolyzing activity by chromatographic procedures resulted in only slight ...
Coal liquefaction investigations required the availability of model compounds for mechanistic investigations. Towards this end, IITRI was funded to develop an approach for the synthesis of one of the target compound. This study was carried out in several phases as outlined here. Initial synthetic investigations on obtaining 2-tetrolol was carried out using high pressure and temperature reduction with Raney nickel catalyst. The next step consisted in incorporation of a hydroxymethyelene group at the C-3 position. This was successfully carried out utilizing 2-tetrolol, formaldehyde, and calcium oxide. An alternate improved method was developed using 3-carboxyl-2-naphthol. This required less time, gave a cheer product in higher yield. Efforts at the introduction of a chloromethylene group only yielded polymeric material or starting material in spite of protection the phenolic group by various groups. They synthesis of 3, 5-dimethyl-6- bromobenzyl chloride was successfully carried out by ...
Coal liquefaction investigations required the availability of model compounds for mechanistic investigations. Towards this end, IITRI was funded to develop an approach for the synthesis of one of the target compound. This study was carried out in several phases as outlined here. Initial synthetic investigations on obtaining 2-tetrolol was carried out using high pressure and temperature reduction with Raney nickel catalyst. The next step consisted in incorporation of a hydroxymethyelene group at the C-3 position. This was successfully carried out utilizing 2-tetrolol, formaldehyde, and calcium oxide. An alternate improved method was developed using 3-carboxyl-2-naphthol. This required less time, gave a cheer product in higher yield. Efforts at the introduction of a chloromethylene group only yielded polymeric material or starting material in spite of protection the phenolic group by various groups. They synthesis of 3, 5-dimethyl-6- bromobenzyl chloride was successfully carried out by ...
The strategy for building SASOL plants reflects a commitment to long-range planning. The first plant, which represented a large investment for a moderate production capacity, was built to establish a technology for reducing South Africa's dependence on imported motor fuels. After the success of the plant, SASOL made plans for a larger plant, which had to be justified solely on economic grounds. At that time, petroleum crude was cheap and plentiful, and the second plant was cancelled. But when OPEC formed and the price of petroleum crude was increased, the South African government reconsidered the plans for another SASOL plant. Furthermore, because the cost of fuels produced at Sasol I proved to be significantly insensitive to inflation and future OPEC price increases were expected, SASOL projected that a new, larger plant should make a profit within a few years after its initial operation. But OPEC prices and inflation have risen even faster than anticipated, and the products ...
The strategy for building SASOL plants reflects a commitment to long-range planning. The first plant, which represented a large investment for a moderate production capacity, was built to establish a technology for reducing South Africa's dependence on imported motor fuels. After the success of the plant, SASOL made plans for a larger plant, which had to be justified solely on economic grounds. At that time, petroleum crude was cheap and plentiful, and the second plant was cancelled. But when OPEC formed and the price of petroleum crude was increased, the South African government reconsidered the plans for another SASOL plant. Furthermore, because the cost of fuels produced at Sasol I proved to be significantly insensitive to inflation and future OPEC price increases were expected, SASOL projected that a new, larger plant should make a profit within a few years after its initial operation. But OPEC prices and inflation have risen even faster than anticipated, and the products ...
The availability of polysilicon feedstock has become a major issue for the photovoltaic (PV) industry in recent years. Most of the current polysilicon feedstock is derived from rejected material from the semiconductor industry. However, the reject material can become scarce and more expensive during periods of expansion in the integrated-circuit industry. Continued rapid expansion of the PV crystalline-silicon industry will eventually require a dedicated supply of polysilicon feedstock to produce solar cells at lower costs. The photovoltaic industry can accept a lower purity polysilicon feedstock (solar-grade) compared to the semiconductor industry. The purity requirements and potential production techniques for solar-grade polysilicon have been reviewed. One interesting process from previous research involves reactive gas blowing of the molten silicon charge. As an example, Dosaj et all reported a reduction of metal and boron impurities from silicon melts using reactive gas blowing ...
A cryogenic separation method of chloromethane (CH{sub 3}Cl) from methyl iodide (CH{sub 3}I) for {delta}{sup 37}Cl measurement with isotope ratio mass spectrometer is described. A cold trap with sealed 2,2,4-trimethylpentane (TMP) as the cryogen is used in this method. CH{sub 3}Cl can be separated from CH{sub 3}I at the TMP melting point (-107 deg. C) based on the difference in the vapor pressure between CH{sub 3}Cl (322.6 Pa) and CH{sub 3}I (lower than 1.3 Pa) at -107 deg. C. After two-step separation processes, the yields of CH{sub 3}Cl purified from CH{sub 3}Cl-CH{sub 3}I mixture are 96-101%, and the difference between the {delta}{sup 37}Cl{sub original} and {delta}{sup 37}Cl{sub Afterseparation} is from -0.06 to +0.06 per mille (0.01 {+-} 0.04 per mille ). These results suggest that CH{sub 3}Cl is completely separated from CH{sub 3}I with no change of {delta}{sup 37}Cl value. This method using the cold trap with sealed TMP is very safe and not harmful, because the liquid organic ...
(-)-N6-(R-4-Hydroxyphenylisopropyl)adenosine (HPIA) was iodinated with NaI and trace /sup 125/I. Mono- and diiodinated reaction products and the starting material were separated by high pressure liquid chromatography and the structures of the reaction products were verified by NMR. (-)-N6-(R-Phenylisopropyl)adenosine (PIA), IHPIA, and I2HPIA decreased rat atrial contractility with ED50 values of 24, 28, and 33 nM, respectively. The contractile effects of these compounds were competitively blocked by theophylline (KI . 7.9 microM), but were not affected by adenosine deaminase. IHPIA also inhibited (-)isoproterenol-stimulated cyclic AMP accumulation in adipocytes with an ED50 (10 nM) and to an extent (83%) nearly identical to PIA. (/sup 125/I)HPIA prepared using carrier-free /sup 125/I bound to adenosine receptors on membranes from rat cerebral cortex, adipocyte ghosts, and heart ventricles. Binding was inhibited stereospecifically by PIA and by other adenosine analogues and ...
The tendency of welded joints from 10Kh14AG15 and 10Kh14AG9 steels to pitting corrosion under the conditions of operating blast-furnace gas purification scrubbers has been investigated. Water in scrubbers contains various quantities of chlorides and sulfates, has pH from 6 to 9 and temperature 65-75 deg. The laboratory corrosion tests have been carried out also on samples turned from the heat-affected zone (h.a.z.) of welded plates at 20 and 65 deg. Anode polarization curves have been read from the Vk corrosion potential at potential shifting rate 0.01 V/min. It is established that in most rigid conditions of scrubbers operating pitting corrosion (PC) rate of chrome-manganese nitrogen-containing steel can reach 2.5 mm/year. At high content of chlorides in water the elevated temperature and external tensile stresses intensify PC. The resistance of welded joints to PC when using welding materials on chromonickel molybdenum base is determined in the first place by ...
2-Azido[#alpha#-"3"2P]adenosine diphosphate (2-azido[#alpha#-"3"2P]ADP) has been used to photolabel the ADP/ATP carrier in beef heart mitochondria. In reversible binding assays carried out in the dark, this photoprobe was found to inhibit ADP/ATP transport in beef heart mitochondria and to bind to two types of specific sites of the ADP/ATP carrier characterized by high-affinity binding (K/sub d/ = 20 #mu#M) and low-affinity binding (K/sub d/ = 400 #mu#M). In contrast, it was unable to bind to specific carrier sites in inverted submitochondrial particles. Upon photoirradiation of beef heart mitochondria in the presence of 2-azido[#alpha#-"3"2P]ADP, the ADP/ATP carrier was covalently labeled. After purification, the photolabeled carrier protein was cleaved chemically by acidolysis or cyanogen bromide and enzymatically with the Staphylococcus aureus V8 protease. In the ADP/ATP carrier protein, which is 297 amino acid residues in length, two discrete regions extending ...
From the dried fruiting bodies of the mushroom Armillaria luteo-virens, a dimeric lectin with a molecular mass of 29.4 kDa has been isolated. The purification procedure involved (NH{sub 4}){sub 2}SO{sub 4} precipitation, ion exchange chromatography on DEAE-cellulose, CM-cellulose, and Q-Sepharose, and gel filtration by fast protein liquid chromatography on Superdex 75. The hemagglutinating activity of the lectin could not be inhibited by simple sugars but was inhibited by the polysaccharide inulin. The activity was stable up to 70 {sup o}C but was acid- and alkali-labile. Salts including FeCl{sub 3}, AlCl{sub 3}, and ZnCl{sub 2} inhibited the activity whereas MgCl{sub 2}, MnCl{sub 2}, and CaCl{sub 2} did not. The lectin stimulated mitogenic response of mouse splenocytes with the maximal response achieved by 1 {mu}M lectin. Proliferation of tumor cells including MBL2 cells, HeLa cells, and L1210 cells was inhibited by the lectin with an IC{sub 5} of 2.5, 5, and 10 ...
In order to optimize the performance of molecular organic electronic devices it is important to study the intermolecular density of states and charge transport mechanisms in the environment of crystalline organic material. Using this approach in Field Effect Transistors (FETs) we show that material purification improves carrier mobility and decreases density of the deep localized electronic state. We also report a general exponential energy dependence of the density of localized states in a vicinity of the mobility edge (Fermi energies up to approx7 times higher than the thermal energy (kT)) in a variety of the extensively purified molecular organic crystal FETs. This observation and the low activation energy of the order of approxkT suggest that molecular structural misplacements of the sizes that are comparable with thermal molecular modes rather than impurity deep traps play a role in formation of these shallow states. We find that the charge carrier mobility in ...
A cytochrome P450 that hydroxylates lauric acid at the 12 position (P450LA omega) was isolated from liver microsomes of clofibrate treated rats. P450LA omega was immunologically distinct from P450s a,b,c,d,e,f,g,h,j,PB1, and PCN1. Polyclonal antibody against P450LA omega was utilized to screen a gt11 cDNA library. A clone (pP450LA omega), was isolated and its sequence determined. The P450LA omega mRNA is a minimum 2387 nts in length and codes for a P450 of Mr.58,222 daltons. This protein shares less than 35% amino acid similarity with P450s b,c,d,e,f,PB1, and PCN1; however, it does contain a hydrophobic amino terminal peptide and a conserved sequence surrounding the Cys residue at position 456, which is similar to other microsomal P450s. P450LA omega is present at high levels in untreated rat kidney and is induced by clofibrate in both kidney and liver. This induction is the result of an accumulation of mRNA through a rapid transcriptional activation of the P450LA gene. Southern ...
A hyaluronic acid binding fraction was purified from the supernatant media of both 3T3 and murine sarcoma virus (MSV) transformed 3T3 cultures by hyaluronate and immunoaffinity chromatography. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis resolved the hyaluronate affinity-purified fraction into three major protein bands of estimated molecular weight (M/sub r,e/) 70K, 66K, and 56K which contained hyaluronate binding activity and which were termed hyaluronate binding proteins (HABP). Hyaluronate affinity chromatography combined with immunoaffinity chromatography, using antibody directed against the larger HABP, allowed a 20-fold purification of HABP. Fractions isolated from 3T3 supernatant medium also contained additional binding molecules in the molecular weight range of 20K. This material was present in vanishingly small amounts and was not detected with a silver stain or with (/sup 35/S)methionine label. The three protein species isolated by ...
MnO2 in pyrolusite can react with SO2 in flue gas and obtain by-product MnSO4 x H2O. A pilot scale jet bubbling reactor was applied in this work. Different factors affecting both SO2 absorption efficiency and Mn2+ extraction rate have been investigated, these factors include temperature of inlet gas flue, ration of liquid/solid mass flow rate (L/S), pyrolusite grade, and SO2 concentration in the inlet flue gas. In the meantime, the procedure of purification of absorption liquid was also discussed. Experiment results indicated that the increase of temperature from 30 to 70 K caused the increase of SO2 absorption efficiency from 81.4% to 91.2%. And when SO2 concentration in the inlet flue gas increased from 500 to 3000 ppm, SO2 absorption efficiency and Mn2+ extraction rate decreased from 98.1% to 82.2% and from 82.8% to 61.7%, respectively. The content of MnO2 in pyrolusite had a neglectable effect on SO2 absorption efficiency. Low L/S was good for both removal of ...
The aim of this paper is to survey the potential of knowledge systems for the management and modelling of energy systems. The paper starts with a short introduction to knowledge systems. The essence of knowledge systems is summarized and described in terms of modelling. Additionally the application of knowledge systems is compared with the use of conventional software on the one hand and human reasoning on the other. Next, research topics which are important in connection with technological applications of knowledge systems are reviewed. This paper follows with a review of knowledge system applications in the field of energy systems and ends with conclusions on the state of the art and required research and development.
DMT has developed what is called the stepped reforming process. This is an allothermal gasification process which uses hydrogen for a gasification medium. First the biomass is pyrolised by means of a heat transfer material. The escaping gaseous and condensable constituents are hydrogenated, heated in a reforming stage and are made to react to a hydrogen-rich product gas by means of homogeneous gasification. The heat required for this is provided by burning the pyrolysis coke. This makes it possible to dispense with process stages that would involve gasification of solid material and hence require higher pressure levels. The present process also works at ambient pressure. Moreover, stepped reforming promises a number of additional advantages: low-tar product gas containing 60% hydrogen, high cold gas efficiency, no wastewater arisings, robust operating behaviour. This paper outlines the basic ideas that led to the development of stepped reforming process and ...
This study investigated the feasibility of using a new adsorbent prepared from coconut coir pith, CP (a coir industry-based lignocellulosic residue), for the removal of uranium [U(VI)] from aqueous solutions. The adsorbent (PGCP-COOH) having a carboxylate functional group at the chain end was synthesized by grafting poly(hydroxyethylmethacrylate) onto CP using potassium peroxydisulphate-sodium thiosulphite as a redox initiator and in the presence of N,N'-methylenebisacrylamide as a crosslinking agent. IR spectroscopy results confirm the graft copolymer formation and carboxylate functionalization. XRD studies confirm the decrease of crystallinity in PGCP-COOH compared to CP, and it favors the protrusion of the functional group into the aqueous medium. The thermal stability of the samples was studied using thermogravimetry (TG). Surface charge density of the samples as a function of pH was determined using potentiometric titration. The ability of PGCP-COOH to remove U(VI) from aqueous ...
This report presents the results of a study of the Japanese MLU magnetic-levitation (maglev) system. The development of the MLU system is reviewed, and the dynamic circuit model then is introduced and applied to the figure-eight-shaped null-flux coil suspension system. Three different types of figure-eight-shaped null-flux suspension systems are discussed in detail: (1) the figure-eight-shaped null-flux coil suspension system without cross-connection; (2) the combined suspension and guidance system; and (3) the combined propulsion, levitation, and guidance system. The electrodynamic-suspension maglev systems developed in Japan seem to be very promising and could result in a commercial application in the near future.
was deemed adequate and a cooling system designed utilizing the Melcor CP2-15- 10B thermoelectric module. Wall temperature achieved with this system was - 36 ...
The activities and the policy in the Netherlands regarding the development of the title systems since 1990 are briefly outlined, focusing on the use of PV-systems in buildings. 5 figs., 1 tab.
Figure 23 presented detailed layout of the cooling system designed for the Mach 6 hypersonic- transport. The distribution system consisted of thin-wall ...
The development of online communication systems related to prevention, decision making, and coping with cancer has outpaced theoretical attention to the attributes that appeal to system...Full Text Available
...Systems by IPEX Enfield electrofusion acid waste systems give you the proven corrosion resistance of polypropylene, along with our patented, state-of-the-art electrofusion system....
This paper presents an analysis of the applicability of alternative systems for electric vehicle (EV) heating and air conditioning (HVAC). The paper consists of two parts. The first part is a cooling and heating load calculation for electric vehicles. The second part is an evaluation of several systems that can provide the desired cooling and heating in EVs. These systems are ranked according to their overall weight The overall weight is calculated by adding the system weight and the weight of the battery necessary to provide energy for system operation. The system with the minimum overall weight is considered to be the best, because minimum vehicle weight decreases the energy required for propulsion, and therefore increases the vehicle range. Three systems are considered as the best choices for EV HVAC. These are, vapor compression, ice ...
This study was carried out mainly to produce uranium trioxide (UO_3), matching standard commercial specification from rock phosphate deposits in Uro and Kurun at eastern part of the Nuba Mountains. A simplified hydrometallurgical procedure has been adopted for production of yellow cake from the ore. The powdered ore sample was leached with concentrated H_2SO_4 acid with and without addition of KCIO_3 as an oxidant. The crude yellow cake was precipitated from the resulting green solution of phosphoric acid as Na_2U_2O_7 and (NH_4)_2U_2O_7 and subsequently purified by TBP extraction (tributylphosphate) and hydrogen peroxide as UO_4.2H_2O. TBP purified product was dried and calcined to UO_3 whereas UO_4.2H-2O was dried and reduced to UO_3 by Na_2S_2O_3. Prior to precipitation of crude yellow cake, Fe in the phosphoric acid solution was precipitated using magnesia. Elemental analysis has shown that the ore is rich in Ca and deficient in elements of potential interest such as Fe, Cu and Zn. ...
The problem on the ratio between the instability of physical systems and tachyons is discussed. It is shown that the tachyons participation in the real physical process of the system rearranging does not contradict any principles. It is noted that the tachyons constitute the most significant element of the systems, identifying the instability relative to the phase transition into the stable state.
Contact scanner system in Wolsung NPP(model ESE-1565) is an early '70 equipment, so most of components are obsolete. To make it 100% compatible, PCBs for this system is the main object of the study. Most of components used in the system are not available ...
This paper details the ongoing collaboration between the U.S. EPA and the U.S. Army Corps of Engineers in the development of complementary micro-computer based cost estimating systems for hazardous waste remediations. he U.S. EPA system, "Remedial Action Cost Estimating System" (...
... 2010-10-01 false Cost estimating system requirements. 252...Clauses 252.215-7002 Cost estimating system requirements. As...use the following clause: Cost Estimating System Requirements (DEC...
... They comprise of a power model for the representation of the electric system, a fluid model that represents the cooling fluid flow, three layers of ...
... POVs) overseas when space was available. ... information management system launched in 2004. ... Personally Procured Transportation (PPT) system ...
The waste monitoring system in use at Los Alamos National Laboratory`s Plutonium Facility, TA-55, is a computer-based system that proves real-time information on industrial effluents. Remote computers monitor discharge events and data moves from one system to another via a local area network. This report describes the history, system design, summary, instrumentation list, displays, trending screens, and layout of the waste monitoring system.
This paper is concerned with the application of a new fuzzy inference method to the design of fuzzy power system stabilizer. Based on Truth-Value-Flow-Inference (TVFI), a fuzzy logic controlled power system stabilizer is proposed to enhance the stability of power system with weak or negative damping. The design of the proposed fuzzy power system stabilizer is presented. Numerical simulation results are presented and compared with two other kinds of fuzzy power system stabilizers. (author)
A micro-computer based fuzzy logic power system stabilizer is applied to a micro-machine system to investigate its efficiency in real time control. The stabilizing signal is determined by using measured speed or real power signals at every sampling time to damp the system oscillations. The results show the proposed stabilizer improves the system damping effectively subject to various types of disturbances.
A mathematical model of the multi machine electric power system to analyse its dynamics has been worked out. The effectivity of the power system stabilizer developed in the one machine system has been tested by means of this model. The influence of the arrangement of the stabilizers on the stability of the electric power system has also been investigated. High damping of electromechanical transient processes has been achieved. 7 refs., 1 tab., 5 figs.
The paper presents a sequential procedure for coordinated stabilization of a multimachine power system with arbitrary complexity of the system model. The most effective machine to be equipped with a power system stabilizer is identified using eigenvalue analysis. The selection is based on the sensitivity of critical eigenvalues to increases in the coefficient of a damping term which is inserted in each equation of motion, in succession. The method is applied to a three-machine system and simulation studies show appreciable improvements in the small disturbance stability of the system.
A heuristic algorithm that employs fuzzy logic is proposed to the power system transmission expansion planning problem. The algorithm is based on the divide to conquer strategy, which is controlled by the fuzzy system. The algorithm provides high quality solutions with the use of fuzzy decision making, which is based on nondeterministic criteria to guide the search. The fuzzy system provides a self-adjusting mechanism that eliminates the manual adjustment of parameters to each system being solved. (author)
An integrated voltage regulator and power system stabilizer based on one step ahead prediction is presented. The fixed parameter predictive control scheme is shown capable of providing consistently good voltage response and contribution to system damping over a wide range of operating conditions and system configuration. This is in contrast to the case with conventional automatic voltage regulator and power system stabilizer where performance varies widely with the operating situation and can even cause system instability. (author)
The Y2K problem may impact on nuclear installations in a number of ways because embedded systems are used in nuclear routine operation, monitoring and control system. The very simplest embedded systems are capable of performing only a single function or set of functions to meet a single predetermined purpose. In more complex systems the functioning of the embedded system is determined by an application program that enables the embedded system to be used for a particular purpose in a specific application. The simplest devices consist of a single microprocessor which may itself be packaged with other chips in a hybrid system or Application Specific Integrated Circuit (ASIC). Its input comes from a detector or sensor and its output goes to a switch or activator which may start or stop the operation of a positioning motors or, by operating a ...
Daylight responsive dimming systems have been used in few buildings to date because they require improvements to improve reliability. The key underlying factor contributing to poor performance is the variability of the ratio of the photosensor signal to daylight workplane illuminance in accordance with sun position, sky condition, and fenestration condition. Therefore, this paper describes the integrated systems between automated roller shade systems and daylight responsive dimming systems with an improved closed-loop proportional control algorithm, and the relative performance of the integrated systems and single systems. The concept of the improved closed-loop proportional control algorithm for the integrated systems is to predict the varying correlation of photosensor signal to daylight workplane illuminance according to roller shade ...
Inputs on radiological conditions forms the basis of implementation of effective exposure control to plant personnel in nuclear power station. Radiation monitoring system provides this input to the plant operator as well as to health physics group. Several design modifications have been incorporated in the Radiation Monitoring System at Tarapur Atomic Power Station (TAPS 3 and 4) over the similar systems at Kakrapar Atomic Power Station (KAPS) and Kaiga Generating Station (KGS). The radiological monitoring systems installed at TAPS unit 3 and 4 includes on line Radiation Data Acquisition System (RADAS), Emergency sampling system, effluent monitoring system and environmental monitoring system. The design changes and the versatile use of these systems are presented in this paper. (author)
A thermodynamic analysis of a hybrid geothermal heat pump system is carried out. Mass, energy, and exergy balances are applied to the system, which has a cooling tower as a heat rejection unit, and system performance is evaluated in terms of coefficient of performance and exergy efficiency. The heating coefficient of performance for the overall system is found to be 5.34, while the corresponding exergy efficiency is 63.4%. The effect of ambient temperature on the exergy destruction and exergy efficiency is investigated for the system components. The results indicate that the performance of hybrid geothermal heat pump systems is superior to air-source heat pumps.
This paper presents case studies of economic feasibility of solar photovoltaic systems using the software AVES-F (Analysis of Economic Feasibility of Photovoltaic Systems), developed by the authors, considering cases of stand-alone and grid-connected systems. The software takes into account several factors that can influence the economic feasibility of these kind of systems, like load to be supplied, distance to the grid, the use regime of the system, applied subsidies and others. The main goal of this paper is to analyze some of these factors and to observe how they can affect the economics of PV systems for electricity generation. (authors)
The notion of hardened systems can be found in several applications (nuclear power plants, alarm systems, research installations..). Their development correspond to the functional necessity to take into account a specific radiative environment. The starting point of each hardening study is the definition of the radiative environmental constraints representative of the application. In addition to these external constraints, the specific functional characteristics of each system are considered: control or interface systems in nuclear industry, in-board control systems, remote handling systems, etc. This paper summarizes the methodology followed according to the experience gained in previous studies and anticipating the future needs. (J.S.). 6 refs., 5 figs.
The term biological motion is often used by researchers studying the patterns of movement generated by living forms and in sports. We studied a pattern recognition system of motion in sport using biological motion data. Biological motion data are acquired using a 3D motion capture system. However, 3D motion capture systems are very expensive. In this article, a biological motion capture system was built using acceleration sensors. Our proposed system uses the technique of Gaussian fitting and regression analysis. We tested our proposed system in pattern recognition of outdoor tennis and its evaluations.
A new power system stabilizer (PSS) design method for single-machine infinite-bus systems is developed. This design method not only assigns the poles corresponding to the electro-mechanical oscillation modes in the system, but also located other system poles in suitable places in the s-plane. The design procedure is used first to translate a PSS design problem to an equivalent constant output feedback controller design problem for a single-input multi-output (SIMO) system. Then, a new algorithm developed in this paper is applied to design a constant output feedback controller to achieve the desired closed-loop system pole locations. Finally, the controller gains are transferred back to the parameters in the PSS. The extension of the method to multi-machine power systems is also illustrated. (Author).
This guide is intended to provide the necessary guidance to successfully manage the NAVMED Navy Occupational Health Information Management System (NOHIMS) at NAVMED sites and the NAVSEA Occupational Safety and Health Record Keeping System (OSHRKS) at NAVSEA sites. Outlines procedures to manage system operations, procedures to resolve hardware, software and communications problems, and procedures outside the realm of system operations that are required for a successful system. This guide is intended for the System and Functional Managers use. The System Manager is the individual designated to provide overall ADP management to the entire local configuration. Usually responsible for file backup, daily operations of the CPU, security, supplies, equipment, operating software and technical ADP guidance to the local functional users.
Fuji Electric has realized highly reliable and functional control systems by the dispersion type control system FOCUS, which uses the controller (ICS-2000) enjoying good reputation in controlling industrial plants for a long time and a personal computer with high windows operability, the former for controlling and the latter for MHI responsible for monitoring. The smelting process in a steel-making plant needs a highly reliable system for advanced control to ensure continuous operation. Fuji Electric delivered the FOCUS system to Kubota in 1998, as the smelting furnace instrumentation/control system for the cupola furnace. The system has been in service smoothly. Moreover, a total of four control systems have been delivered, 2 for steel-making furnaces and the other 2 for continuous casting. (NEDO)
The Reliability Data Management System (RDMS) for safety systems of PHWR type plants has been developed and utilized in the reliability analysis of the special safety systems of Wolsong Unit 1 with plant overhaul period lengthened. The RDMS is developed for the periodic efficient reliability analysis of the safety systems of Wolsong Unit 1. In addition, this system provides the function of analyzing the effects on safety system unavailability if the test period of a test procedure changes as well as the function of optimizing the test periods of safety-related test procedures. The RDMS can be utilized in handling the requests of the regulatory institute actively with regard to the reliability validation of safety systems.
There are many different types of open pit mining operations around the world, and the challenge for any drive system manufacturer is to produce a system(s) that will work satisfactorily in these mines. Several factors must be considered such as vehicle speed requirements, available engine horsepower, mine rolling resistance, grades, grade lengths, payload, and tire sizes. How well a particular drive system performs depends on the size, weight, and available tractive/retarding effort. In addition to performance, the system must also have an operating cost that will be acceptable over the life of the equipment. Today the choice of drive systems is not only between mechanical and electrical drives, but also within these categories are the different manufacturers. Regardless of how the power is provided to the rear wheels, the job must be accomplished reliably and at an acceptable ...
A novel adaptive stabilizer, called an Adaptive Governor Power System Stabilizer (AGPSS), which operated on the governor turbine system, was described. There has been extensive research on adaptive excitation control of generators in power systems with the goal of achieving better dynamic performance. AGPSS tracks the frequency and damping of oscillations in a power system, and adjusts to ensure that there is always sufficient damping in the system. There is no interaction between stabilizers on different generating units, and each one acts independently, consuming oscillation energy locally. These stabilizers are easy to design and this facilitates their use in multimachine systems. Results obtained by nonlinear simulation of a single-machine and a three-machine power system were discussed, illustrating the effectiveness of the stabilizers ...
Several systems have been developed to accomplish vehicle location. The systems consist of three types: Dead Reckoning, Satellite, and LORAN C. If the information is to be sent back to a central location, some type of radiocommunication system is needed. One can use the existing voice radio or add a radio system just for transmitting the data.
A decoupled characteristic between the damping of a specific swing mode and the stabilizer gain of the corresponding machine in multimachine power systems is identified. Using this decoupled characteristic a power system stabilizer (PSS) synthesis approach which is based on the phase compensation concept is verified on a 9-machine system and the dynamic performance of this system is significantly improved. This method is proved to be effective, simple and it can provide useful guidance for the PSS field tuning.
This paper establishes a standardization procedure in which results are presented in ready-to-use charts for the economic evaluation of biogas plants. It is hoped this work will alleviate controversial reports on cost-effectiveness of biogas systems. Also, it is found that these systems are the most economic among renewable energy systems using a standardized procedure for their comparison augmented by the generated spider diagrams wherein most probable costing production values for each system are directly compared. (author).
A semi-automatic system which considers operation in a face by monitoring technological parameters of an extraction vehicle and a longwall conveyor is examined. The system records in tabular form the location, progress made, operating and down time of an extraction vehicle and operating and down time of the conveyor. A description of the operating principle system and systems for arrangement of the remote sensing and central recording device are presented. (Note: extraction vehicle not identified: LTN)
A tiered communications architecture for managing network traffic in a distributed system. Communication between client or control computers and a plurality of hardware devices is administered by agent and monitor devices whose activities are coordinated to reduce the number of open channels or sockets. The communications architecture also improves the transparency and scalability of the distributed system by reducing network mapping dependence. The architecture is desirably implemented in a proton beam therapy system to provide flexible security policies which improve patent safety and facilitate system maintenance and development.
This book contains the proceedings of the International Topical Meeting on Remote Systems and Robotics in Hostile Environments. It is organized under the following sessions: Worldwide Applications Overview; Operating Mobile Systems; Sensors and Control Systems; Space Applications; Reactor Operations and Surveillance; Remote Equipment for Hazardous Operations; Future Mobile System; Mining and Construction Operations; Special Applications; Hot Cell Applications; Processing; Reactor Operations and Maintenance; Decontamination and Waste Handling; Remote Handling Development and Demonstration.
Solutions have been found for the problems encountered with the coil power and switching systems of the International Fusion Superconducting Magnet Test Facility (IFSMTF). The coil power system provides the filtered dc sources (+- 12 V dc; 25,000 A) for charging and discharging the coils of the IFSMTF experiment. The switching system provides the means of transferring the coil current into a dump resistor when a rapid discharge of a coil is required due to a coil failure (quench) or other system abnormalities.
The basic design of a system installed in the Columbus, Ohio Zoo is described. The distribution system is described in detail. The control system is microprocessor controlled, with about 50 monitoring points. Preliminary evaluations have indicated that the system can operate with an overall coefficient of performance in excess of 3.5. 1 figure.
The purpose of this paper is to describe instrumentation and control (I C) system improvements at Experimental Breeder Reactor 11 (EBR-11). The improvements are focused on three objectives; to keep the reactor and balance of plant (BOP) I C systems at a high level of reliability, to provide diagnostic systems that can provide accurate information needed for analysis of fuel performance, and to provide systems that will be prototypic of I C systems of the next generation of liquid metal reactor (LMR) plants.
The purpose of this paper is to describe instrumentation and control (I&C) system improvements at Experimental Breeder Reactor 11 (EBR-11). The improvements are focused on three objectives; to keep the reactor and balance of plant (BOP) I&C systems at a high level of reliability, to provide diagnostic systems that can provide accurate information needed for analysis of fuel performance, and to provide systems that will be prototypic of I&C systems of the next generation of liquid metal reactor (LMR) plants.
Computed radiography (CR) systems use a photostimulable phosphor plate enclosed in a cassette. In CR, image acquisition is a two-stage process wherein image capture and image read out are done separately. Direct digital radiography (DR) systems, on the other hand, use detectors that have a combined image capture and image read out capability. DR systems are also called as DDR or ddR systems by some vendors. This article focuses on DR systems
The purpose of this paper is to describe the embedded computer systems approach taken at Experimental Breeder Reactor II (EBR-II) for non-safety related systems. The hardware and software structures for typical embedded systems are presented The embedded systems development process is described. Three examples are given which illustrate typical embedded computer applications in EBR-II.
In this paper, we extend the diversity and multiplexing tradeoff (DMT) analysis from point-to-point channels to cellular systems to evaluate the impact of inter-cell interference on the system reliability and efficiency. Fundamental tradeoff among diversity order, multiplexing gain and inter-cell interference intensity is characterized to reveal the capability of multiple antennas in cellular systems. And the detrimental effects of the inter-cell interference on the system performance of diversity and multiplexing is presented and analyzed.
Using the Philips DRM distributed real-time multiprocessing system, designers can implement high-performance computer systems using VME hardware and the C programming language. The system provides a virtual-processing environment in which several 68000 CPUs share the workload. There are no centralized components, and tasks can be assumed by the rest of a system in the event of an individual processor's failure.
The report examines common ventilation and air conditioning systems and strategies for both domestic and commercial buildings; and covers issues such as energy conservation, indoor air quality and occupant comfort. Drawing data from many countries in Europe and the United States of America, various natural, mechanical and air conditioning systems were compared using criteria such as climate, level of occupant interaction, and level of system comfort. This classification system is evaluated and seen as a valuable framework for further research. (U.K.)
Within this paper the potentialities of using networked embedded systems will be discussed. New embedded hardware with network connectivity allows remote administration and software updates of solar thermal system controllers via internet. System self analysis helps to minimize breakdown times by sending email and SMS to request maintenance staff. (orig.)
This paper describes New York State Electric and Gas Corporation`s concept for a comprehensive, centrally located data system for management of their continuous emission monitoring systems (CEMS) data. The topics of the paper include the power system`s mix of generating units; data reporting requirements; data base management; nitrogen oxides compliance tracking; sulfur dioxide, nitrogen oxides, carbon dioxide and flow monitoring; and allowance tracking.
The conceptual system requirements for the control, data, robotics, and project management (CDRM) system for the next generation of fusion experiments are developed by drawing on the success of the Tara control and data system. The requirements are described in terms of an integrated but separable matrix of well-defined interfaces among the various systems and subsystems. The study stresses modularity, performance, cost effectiveness, and exportability.
This report deals with the selection of a data communication system for a remote metering system. It covers the following three types of systems: fiber optic, telephone line, and radio packet. It provides a methodology for selecting a communication system for a given remote metering system and a method for comparing costs.
A knowledge based system for pitting corrosion is presented. It can be used for material selection for specific pitting corrosion conditions or to check the suitability of a chosen material. The user can enter his own knowledge. The expert system is an integration of traditional expert system technology and neural networks. (orig.)
In this paper the robust stability analysis of a single machine infinite bus system is investigated using interval matrix theory. Specifically the parameters of the power system stabilizer are considered as uncertainties in the system A matrix. The range of these parameters for which the system is Hurwitz stable is then found using interval matrix theory. (Author)
Dynamic stability improvement of a longitudinal power system using a power system stabilizer (PSS) and a static VAR compensator (SVC) is reported in this paper. An analytical approach is developed for the determination of PSS parameters. Results from time domain simulations indicate that the PSS and the SVC are very effective in damping system oscillations.
Software quality assurance (SQA) for robotic systems used in nuclear waste applications is vital to ensure that the systems operate safely and reliably and pose a minimum risk to humans and the environment. This paper describes the SQA approach for the control and data acquisition system for a robotic system being developed for remote surveillance and inspection of underground storage tanks (UST) at the Hanford Site.
One of the requirements for a federated information system is interoperability, the ability of one computer system to access and use the resources of another system. This feature is particularly...Full Text Available
Transposon-based integration systems have been widely used for genetic manipulation of invertebrate and plant model systems. In the past decade, these powerful tools have begun to be used in...Full Text Available
Immunotoxicity encompasses both reduced and heightened immune function. Diverse chemicals can impair functioning of the immune system. Both monographs and books have been devoted to detailed descriptions...Full Text Available
The Time Projection Chamber (TPC) magnet at LBL and its compensation solenoids are adiabatically stable superconducting solenoid magnets. The cryogenic system developed for the TPC magnet is discussed. This system uses forced two-phase tubular cooling with the two cryogens in the system. The liquid helium and liquid nitrogen are delivered through the cooled load by forced tubular flow. The only reservoirs of liquid cryogen exist in the control dewar (for liquid helium) and the conditioner dewar (for liquid nitrogen). The operation o these systems during virtually all phases of system operation are described. Photographs and diagrams of various system components are shown, and cryogenic system data are presented in the following sections: (1) heat leaks into the TPC coil package and the compensation solenoids; (2) heat leaks to various ...
This report gives the results of a survey of operational flue gas desulfurization (FGD) systems on coal-fired utility boilers in the United States. The FGD systems installed on Units 1 and 2 at the Bruce Mansfield Station of the Pennsylvania Power Company...
This document establishers the Software Configuration Management Plan (SCMP) for the software associated with the control system of the Sodium Removal System (SRS) located in the Interim Examination and Maintenance (IEM Cell) Facility of the FFTF Flux Test.
This work describes a combinatorial model for estimating the reliability of the embedded digital system by means of multi-state function. This model includes a coverage model for fault-handling techniques implemented in digital systems. The fault-handling techniques make it difficult for many types of components in digital system to be treated as binary state, good or bad. The multi-state function provides a complete analysis of multi-state systems as which the digital systems can be regarded. Through adaptation of software operational profile flow to multi-state function, the HW/SW interaction is also considered for estimation of the reliability of digital system. Using this model, we evaluate the reliability of one board controller in a digital system, Interposing Logic System (ILS), which is installed in YGN nuclear ...
Systemic chemotherapy has been relatively ineffective in the treatment of malignant brain tumors even though systemic chemotherapy drugs are small molecules that can readily extravasate across the porous...Full Text Available
When any new accelerator or storage ring is built that advances the state of the art, the diagnostic system becomes extremely important in tuning the facility to full specification. This paper will discuss the various diagnostic devices planned or under construction for the PSR and their connection into the control system.
Plants have too long been ignored as useful screening and monitoring systems of environmental mutagens. However, there are about a dozen reliable, some even unique, plant genetic systems that can increase...Full Text Available
The highly variable and intermittent pollutant concentrations and flowrates associated with wet-weather events in combined sewersheds necessitates the use of storage-treatment systems to control pollution.An optimized combined-sewer-overflow (CSO) control system requires a manage...
A tutorial account is given of the main characteristics and distinctive features of conceptual magnetic fusion systems employing the magnetic mirror principle. These features are related to the potential advantages that mirror-based fusion systems may exhibit for the generation of economic fusion power.
1 to the operator of a waste collective system by an agreement or contract. The conditions for the ...Fees of the waste collective system are subject to the supervision of the authority responsible for market surveillance. ...The operator of waste collection system collects wastes from producers and holder and transports these to a collection
User acceptance of a computer system depends on a number of factors, including broad social and professional concerns regarding the system's impact on the work environment. This observation is especially...Full Text Available
This book provides differential diagnostic possibilities of specific scan abnormalities in one volume for easy reference. This book is organized by organ systems and covers the central nervous system, the endocrine, skeletal, pulmonary, gastrointestinal, genitourinary, and cardiovascular systems. The gamuts are designed to teach differential diagnosis and to assist in the actual interpretation of patient slides.
An overview is presented of the FFTF reactor and plant together with descriptions of core components, core internals, core system, primary and secondary control rod system, reactor instrumentation, reactor vessel and closure head, and supporting test programs. (DG)
An overview is presented of the FFTF reactor and plant together with descriptions of core components, core internals, core system, primary and secondary control rod system, reactor instrumentation, reactor vessel and closure head, and supporting test programs.
This paper describes the technical design and performance of the diagnostic system installed in the tokamak TCABR to measure parameters of the plasma edge. The system consists of four Langmuir probes under remote control. (author)
The 'high-tension distribution line design support system' was developed for the 'work design support system'. This support system is composed of the work outline editor for preparing work details and facility data and the inference engine for preparing practical design plans, and can check system conditions such as voltage drop and deviation from technical standards automatically. The work outline editor takes charge of selection of work items, selective input of system information, and setting of some conditions such as pole position and reserved load onto a system diagram. The inference engine provides the design plan automatically based on the information inputted by the editor. For the design of high-tension distribution line, such various factors as local condition and load sharing of distribution ...
This report presents a study on the use of computerised, continuous remote monitoring systems for fire and explosive atmosphere safety in underground coal mines. The effects of these systems on the safety level in mines are investigated, and the relationship between mine safety regulations and computerised, continuous, remote monitoring is analysed.
The objective of this project is to reduce energy consumption in 203 buildings by providing a new EMCS (Energy Monitoring Control System) to control and monitor systems.
The author compares the UHF Follow-on and MILSTAR satellite communication systems. The comparison uses an analytical hierarchy process. Although the two systems have been tasked with different missions, a comparison of cost, capability, and orbit is condu...
Our understanding of the development of neurotransmitter systems in the central nervous system has increased greatly over the past three decades and it has become apparent that drug effects...Full Text Available
A closed loop control process assures that a system performs within control limits. In closed loop control, the system's output feeds back directly to change the system's inputs. We describe an approach...Full Text Available
A simple beam-forming system is described for the electrostatic accelerator of the Scientific-Research Institute of Nuclear Physics of Moscow State University. The system allows the beam to be focused on targets at various distances for a conductor potential of from 1 to 4 MV and beam currents of up to 35 #mu# A.
Algebraic properties of the analytical model, describing electro-magnetic weak interaction with the two-level system with two-fold degenerate state are considered. The expressions for the coherent states and Green function of the system are obtained.
Incorporation of clinical decision support (CDS) capabilities is required to realize the greatest benefits from computerized provider order entry (CPOE) systems. Discussions at a conference on CDS in...Full Text Available
This paper presents the design and implementation of a clinical picture archiving and communication system (PACS) module within the radiology department of a 700-bed teaching hospital. The system is...Full Text Available
... in this paper is aimed at developing a computer vision system that will be used to automatically grade rough hardwood lumber. The purpose of the computer vision system is to locate and identify grading def...
...Acquisition Regulations System 3 2010-10-01...Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF...assumption of risk for transportation by conveyance on...Missiles, and Space Launch Vehicles,...
The present paper considers the evaluation of timber structures with the focus on robustness due to connection ductility. The robustness analysis is based on the structural reliability framework applied to a simplified mechanical system. The structural timber system is depicted as a parallel system. An evaluation method of the ductile behaviour is introduced. For different ductile behaviours, the system reliability is estimated based on Monte Carlo simulation. A correlation between the strength of the structural elements is introduced. The results indicate that the reliability of a structural timber system can be significantly increased due to the ductile behavior.
This paper proposes the design of LQ-PSS (linear quadratic power system stabilizer) for improving power system stability using genetic algorithm(GA). We are turned weighting matrices of LQ-PSS using GA. To evaluate the usefulness of the proposed method, we performed the nonlinear simulation on a single machine infinite system. As results on a single machine infinite system. As results of the simulation, the proposed method shows the better control performance than CPSS(conventional power system stabilizer) in terms of settling time and damping effects. (author). 7 refs., 7 figs., 3 tabs.