WorldWideScience
1

The behavior of waste rock piles; Le comportement des haldes de steriles  

Energy Technology Data Exchange (ETDEWEB)

Under the auspices of the Mine Environment Neutral Drainage (MEND) Program, several waste rock piles were monitored and characterized. Acid rock drainage (ARD) became a mechanism better understood based on the data acquired during these projects. Numerical simulation was used to better comprehend the quantitative issues associated with the characterization of three specific sites for the purpose of this study. The sites selected were the south waste rock pile of the Doyon Mine in Quebec, the Northdale of the mining district of Ronnenberg in Germany, and the waste rock pile of the Sugar Shack South of the Questa mine in New Mexico. The observed and simulated conditions were very distinct from one mine to another, even if the same mechanisms were involved. The dominant oxygen and heat transfer mechanisms displayed the most varied behavior between the sites. ARD control or site rehabilitation decisions ...

2000-07-01

2

LAW ON WASTE MANAGEMENT  

Wastenet

1 to the operator of a waste collective system by an agreement or contract. The conditions for the ...Fees of the waste collective system are subject to the supervision of the authority responsible for market surveillance. ...The operator of waste collection system collects wastes from producers and holder and transports these to a collection

3

Decommissioning of French nuclear submarines  

Energy Technology Data Exchange (ETDEWEB)

Since the beginning of the sixties, France has developed a fleet of nuclear powered vessels. Insofar as the ships of the 2. generation are being built, the older ones are decommissioned and enter the dismantling process. The average rate is presently one submarine decommissioned every two or three years. The overall strategy for the decommissioning of French nuclear submarines can be brought down to 3 phases: 1. Level 1 dismantling which essentially consists in: - unloading the spent fuel and storing it in a pool ; - possibly emptying the circuits which contain radioactive liquids. The level 1 is easily achieved, as it is not very different from the plant situation during ship overhaul or major refits. 2. Level 2 dismantling which consists in isolating the nuclear reactor compartment from the rest of the submarine and conditioning it for interim storage on a ground facility located inside Cherbourg Naval Dockyard. The rest of the ship is decontaminated, controlled ...

2003-07-01

4

The building tomorrow and after..; Le batiment demain et apres-demain..  

Energy Technology Data Exchange (ETDEWEB)

During its jubilee, the French building technical and scientific centre (CSTB) has organized a colloquium about the future tendencies of buildings evolution in the 20 forthcoming years: autonomy in energy production and wastes or effluents management, reduction of water consumption and management of water, hot water production and space heating, bio-sensors for the management of indoor air-quality, control of noise environment using active acoustic systems etc.. (J.S.)

1998-01-01

5

Present State of Radioactive Waste Management and Treatment Technology at the Research Centre Seibersdorf  

International Nuclear Information System (INIS)

Since 1976 the Austrian Research Centre Seibersdorf has the task to collect, treat and store radioactive waste (Radwaste) arising in Austria. Within the Department of Waste Management a variety of appropriate treatment systems are installed. For storing unconditioned and conditioned waste proper storage-halls are available. The collection of Radwaste is carried out using 100 l drums, for the conditioned waste the 200 l drum concept is used. The interim storage of conditioned waste is done at Seibersdorf until a final repository is built. The present plan foresees one to be in operation at the year 2012. (author).

1996-10-07

6

Composting - environmentally compatible waste disposal - one of the incredients of waste management  

Energy Technology Data Exchange (ETDEWEB)

Considering the fact that more than 40% of all household wastes are organic wastes composting could be an excellent relief and complement to other waste disposal methods (e.g. combustion or direct landfills). Provided the right conditions household wastes could be composted together with sewage sludges and manures. The paper discusses the legal aspects, quantitative evaluations, conveying systems, as well as the compost utilization and marketing aspects valid for the Federal Republic of Germany.

1988-09-20

7

Conditioning of plastic wastes for thermal utilization; Aufbereitung von Kunststoffabfaellen zur thermischen Verwertung  

Energy Technology Data Exchange (ETDEWEB)

This article describes the processes for the treatment of plastic waste: sampling, sorting, comminution. The requirements for the different processes for waste treatment (as recycling, utilization as raw material, energy recovery, combustion) are listed. (SR)

1996-12-31

8

Survey reveals Europe's refinery-waste disposal methods, amounts, and costs  

Energy Technology Data Exchange (ETDEWEB)

Results of a survey conducted by Concawe on 75 oil refineries in Europe show that the total quantity of waste requiring disposal in 1986 was 0.5 million metric tons. This quantity of waste is but 0.13% of the total refinery throughput of 387 million metric tons during 1986. The survey revealed a wide range of disposal costs, depending on the particular properties of the waste and local conditions. A summary of total waste generation and how the waste is disposed of is shown. Details on the types of waste disposed, the disposal methods used, and the costs of disposal are detailed in this excerpt from the Concawe survey.

1989-08-28

9

Waste recycling as evaluated from the viewpoint of energy environment, mainly about plastics; Haikibutsu recycle no energy kankyomen kara no hyoka. Plastic wo chushin to shite  

Energy Technology Data Exchange (ETDEWEB)

Some comments are given on the recycling of waste, mainly plastics, as evaluated from the viewpoint of energy environment. Discussed about the waste in general are the definition and classification, generation and resource recovery rates, current state of recycling, problems about recycling, related legislation, and current conditions overseas. Discussed about the treatment and recycling of plastics waste are the characters and use of plastic product, current state of waste plastics treatment, current state of waste plastics recycling (material recycling, thermal recycling), energy recovery by thermal recycling, quantity recyclable from waste plastics, energy consumption and cost for waste plastics recycling, effect and impact of increase in waste plastics in case material recycling is forwarded, and ...

1996-05-01

10

Certified Reference Materials (CRM) for the quality control of metals chemical forms determinations in environment, in support to the European Union legislation; Materiaux de reference certifies pour le controle de qualite des determinations de formes chimiques des metaux dans l`environnement, en soutien a la legislation de l`Union Europeenne  

Energy Technology Data Exchange (ETDEWEB)

This work gives a global view of legislations in which are included metals chemical states, briefly recalls the conditions to be respected for the CRM (Certified Reference Materials), and describes the results of some current plans for the Norms, Measures and Tests program. (O.M.) 23 refs.

1997-03-01

11

A nonmolecular derivation of Maxwell's thermal-creep boundary condition in gases and liquids via application of the LeChatelier-Braun principle to Maxwell's thermal stress  

Science.gov (United States)

According to the LeChatelier-Braun principle, when a closed quiescent system initially in an equilibrium or unstressed steady state is subjected to an externally imposed ``stress'' it responds in a manner tending to alleviate that stress. Use of this entropically based qualitative rule, in combination with the notion of Maxwell thermal stresses existing in nonisothermal gases and liquids, enables one to (i) derive Maxwell's thermal-creep boundary condition prevailing at the boundary between a solid and a fluid (either gas or liquid) and (ii) rationalize the phenomenon of thermophoresis in liquids, for which, in contrast with the case of gases, an elementary explanation is currently lacking. These two objectives are achieved by quantitatively interpreting the heretofore qualitative LeChatelier-Braun notion of stress in the present context as being the fluid's stress tensor, the latter including Maxwell's thermal stress. In ...

2009-05-01

12

Thermal denitration and mineralization of waste constituents  

Energy Technology Data Exchange (ETDEWEB)

In order to produce a quality grout from LLW using hydraulic cements, proper conditioning of the waste is essential for complete cement curing. Several technologies were investigated as options for conditions. Since the LLW is dilute, removal of all, or most, of the water will significantly reduce the final waste volume. Neutralization of the LLW is also desirable since acidic liquids to not allow cement to cure properly. The nitrate compounds are very soluble and easily leached from solid waste forms; therefore, denitration is desirable. Thermal and chemical denitration technologies have the advantages of water removal, neutralization, and denitration. The inclusion of additives during thermal treatment were investigated as a method of forming insoluable waste conditions.

1997-08-01

13

Cd speciation in biomass fly ash particles after size separation by centrifugal SPLITT  

Energy Technology Data Exchange (ETDEWEB)

The finest particle size fractions ({le} 25 {mu}m) in four fly ash samples from fluidised bed combustion of three biomass based fuels and a municipal solid waste fuel were size separated using a centrifugal SPLITT fractionation cell. The ashes were separated into different size fractions and the cadmium concentration, partition and speciation in each separated fraction were then investigated in relation to their possible leaching. The fractionation was evaluated by environmental scanning electron microscopy, which also provided indications of the associations between Cd and other main elements on the particles through the use of X-ray fluorescence mapping. The total concentration of Cd in each fraction was determined by AAS analysis which showed different dependence on the ash particle size in the case of biomass or waste fuels. In addition, the speciation of Cd in each fraction, investigated by sequential chemical ...

2002-08-01

14

Influence of vanadium doping on the electrochemical behaviour of MnO{sub 2} rutile; Influence du dopage par le vanadium sur le comportement electrochimique de MnO{sub 2} rutile  

Energy Technology Data Exchange (ETDEWEB)

Vanadium doped manganese bi-oxide has been obtained from a solution containing both cations. The X-ray diffraction of this material indicates a rutile-type phase but the enlargement of some lines supports the existence of several lattice defects. Also the particle size of the doped material is significantly smaller than the one of the non-doped material obtained in the same conditions. The presence of pentavalent vanadium inside the lattice leads to a small amount of trivalent manganese. Electron microscopy shows the existence of defects which have a tendency of becoming well-ordered and to stabilize a sur-structure. At ambient temperature, the electrochemical behaviour of doped manganese bi-oxide is greatly improved when compared to the non-doped phase. This behaviour is due to the presence of numerous lattice defects and to the smaller size of crystallites. In polymer batteries, the behaviour is similar the one of the non-doped material for which the kinetics ...

1996-12-31

15

The Formation of the Low-sized High Density Plasma Structures in the Self-maintained Plasma-beam Discharge  

International Nuclear Information System (INIS)

The opportunity of use self-maintained plasma-beam discharge in an extended pulsing plasma diode of low pressure for making powerful sources of the soft X-rays is investigated. Conditions of formation of the self-maintained plasma-beam discharge are determined. The mode of making of dense high-temperature plasma on the basis of stannum ions in the discharge is shown. The stannum ions are used as a working element of a radiation sources at pulsing power of electron beam P?10...100 MW. Results of the examination on formation of the dense (np?1016 cm3), small sizes (le?100 eV in conditions of working material evaporation from the anode are given. The total contribution of energy to the discharge has made W < 20 J.

2006-01-01

16

Three-dimensional assessment of the propagation and concentration distribution of waste gas from waste incinerators and sanitary landfills in built-up areas by means of specific examples. Dreidimensionale Erfassung der Ausbreitung und Konzentrationsverteilung von Abgaben aus Muellverbrennungsanlagen und Deponien in bebauten Gebieten an konkreten Beispielen  

Energy Technology Data Exchange (ETDEWEB)

Within the framework of efforts to optimize state-of-the-art waste disposal methods, this research project makes a theoretical analysis of the propagation behaviour of pollutants from landfills and waste incineration plants into the immediate vicinity of such plants. In order to judge the propagation of pollutants near the above-mentioned waste disposal facilities, a calculation program was developed within the framework of this research project which permits simulation of the propagation of such emissions in a three-dimensional space by application of an Eulerian grid model. It is capable of realistically representing fluid flow conditions and pollutant concentrations for certain points of times within the complex building patterns of such plants, for randomly chosen atmospheric conditions. (orig.)

1992-01-01

17

Isotopic effects on solubility-limited mass transfer  

Energy Technology Data Exchange (ETDEWEB)

In our previous theoretical analyses, solubility-limited mass transfer from waste solids applies if a species is at a constant elemental concentration in liquid at the waste surface. For an element with isotopes that decay appreciably during the time of interest, a solubility boundary condition results in a time-dependent boundary concentration of each isotope. Here we present mass-transfer equations that include the effects of isotopic decay boundary conditions. 9 refs., 1 fig.

1989-06-01

18

Comprenhensive Program of Engineering and Geologic Surveys for Designing and Constructing Radioactive Waste Storage Facilities in Hard Rock Massifs  

Energy Technology Data Exchange (ETDEWEB)

Geological, geophysical, and engineering-geological research conducted at the 'Yeniseisky' site obtained data on climatic, geomorphologic, geological conditions, structure and properties of composing rock, and conditions of underground water recharge and discharge. These results provide sufficient information to make an estimate of the suitability of locating a radioactive waste (R W) underground isolation facility at the Nizhnekansky granitoid massif

2002-12-27

19

Second mission of North-Cotentin radio-ecology group. The uncertainty calculation; Deuxieme mission du Groupe Radio-ecologie Nord-Cotentin. Le calcul d'incertitude  

Energy Technology Data Exchange (ETDEWEB)

The present study treats only the collective risk of ex-utero leukaemia associated with the routine releases of the nuclear industrial installations of the North Cotentin (0.0009 cases over the considered period) the uncertainty on the contribution to the collective risk of the incidents and the accidents of the nuclear installations (notably the drilling of the pipe of release in sea arisen in 1979-1980 and the fire of the waste silo on January 6. 1981, for the reprocessing plant of La Hague has not been considered. Only 45% of the risk are taken into account by the study. Every calculated value remains very inferior to the number of leukemia cases observed (4 cases observed for two expected cases) and to the risk of radioinduced leukemia any merged exposure sources, that is to say 0.84 cases. It appears thus not very probable that the nuclear installations of the North - Cotentin can explain the tendency to the excess of observed leukaemia. The limits of the ...

2003-03-15

20

Comparative cold resistance of three Columbia River organisms  

Science.gov (United States)

Resistance to abrupt and gradual cold shock was determined in bioassays with pumpkinseed (Lepomis gibbosus), rainbow trout (Salmo gairdneri), and a northwestern crayfish (Pacifastacus leniusculus) acclimated to higher temperatures at 5 C increments. Test criteria were median tolerance limits (TLm) for 96-h exposures after abrupt cold shock, and 50 percent loss of equilibrium (LE50) for decline rates of 18, 15, 10, 5, and 1 C/h during gradual cold shock. Cold resistance depended on original acclimation temperature (AT) and varied among species under both test conditions in the order: pumpkinseed less than rainbow trout less than crayfish. The lower TLm limit for pumpkinseed was 12.3 C at 30 C AT, 9.6 C at 25 C AT, 4.5 C at 20 C AT, and 2.7 C at 15 C AT. Rainbow trout at 20, 15 and 10 C AT survived abrupt exposures to cold down to 3.3, 1.4 and 0.5 C, respectively. Crayfish at 25, 20 and 15 C AT survived exposures down to 2.5, 0.4 and 0.0 C, ...

1977-03-01

21

Terms and Conditions - Waste Aware Business  

Wastenet

... Governing Law These terms and conditions of use shall be governed by the laws of Scotland and are subject to the exclusive jurisdiction of the Scottish Courts. 7. Website Policies, Modification and Severability We reserve the right to make changes to this website, our policies and these terms and conditions of use at any time. If any of these conditions shall be deemed invalid, void ...

22

Basic design of alpha aqueous waste treatment process in NUCEF  

Energy Technology Data Exchange (ETDEWEB)

This paper described the basic design of Alpha Aqueous Waste Treatment Process in NUCEF. Since various experiments using the TRU (transuranium) elements are carried out in NUCEF, wastes containing TRU elements arise. The liquid wastes in NUCEF are categorized into three types. Decontamination and volume reduction of the liquid waste mainly of recovery water from acid recovery process which has lowest radioactive concentration is the most important task, because the arising rate of the waste is large. The major function of the Alpha Aqueous Waste Treatment Process is to decontaminate the radioactive concentration below the level which is allowed to discharge into sea. Prior the process design of this facility, the followings are evaluated:property and arising rate of the liquid waste, room space to install and licensing ...

1996-11-01

23

Innovating methodologies brought into operation by Framatome for the Phenix control; Methodologies innovatrices mises en oeuvre par Framatome pour le controle de Phenix  

Energy Technology Data Exchange (ETDEWEB)

The renovation programme of the Phenix nuclear power plant (fast neutrons reactor situated at Marcoule) has for objective to ensure the reactor operation lengthening. In this frame, expertise and monitoring operation in situ of materials have been started. The presence of sodium and a temperature at the cold breakdown of the primary circuit between 150 and 180 degrees (Celsius) imply, for fast reactors, very special conditions. In this context, Framatome has realised three intervening in the area of nondestructive testing: the inspection of the cone-shaped support ring, the monitoring of the upper part of the primary vessel and the monitoring of the intermediary exchanger equipment. (N.C.)

2000-06-01

24

For its batteries, the automobile imitates the cellular phone; Pour ses batteries, la voiture imite le telephone mobile  

Energy Technology Data Exchange (ETDEWEB)

To gain in efficiency, lightness and volume, the hybrid and electric-powered cars will certainly follow the cellular phone path. The key of success of todays hybrid cars is the Ni-MH battery developed by Matsushita (87.5% of the market in 2004). The lithium-ion batteries will be the next step and would allow to supply 80 to 100% of the energy of the vehicle, the thermal engine becoming just an auxiliary system for additional power, autonomy and air-conditioning. Prototypes can reach today 200 to 450 km of autonomy and 130 km/h speeds with batteries of about 200 kg. If most of the safety problems linked with the Li technology have been solved, the main drawback remains the cost of the Li-ion technology. Short paper. (J.S.)

2005-09-28

25

Development of a petrographic technique for the quality control of concrete mixes used in mines. Final report; Mise au point d`une technique petrographique pour le controle de qualite des betons miniers. Rapport final  

Energy Technology Data Exchange (ETDEWEB)

Petrographical analysis is a microscopical analytical tool which allows definition of the exact nature of the components of different concrete mixes, as well as definition of internal structures and alteration processes. In order to improve the precision and the swiftness of the petrographical analysis, an automated image analysis system has been developed. In the next stage of this study, which consisted in the testing of new concrete mixes containing fluidised bed ashes, petrography has been used, not only to identify the nature of the mix components, but also assess the behaviour of these new concrete mixes when exposed to aggressive conditions.

1997-11-01

26

Chromium stabilization chemistry of paint removal wastes in Portland cement and blast furnace slag  

Energy Technology Data Exchange (ETDEWEB)

The use of cement based systems for solidification and stabilization of hazardous wastes has been proposed. The stabilization of Cr contaminated paint removal wastes in ordinary Portland cement and in a Portland cement and blast furnace slag matrix was investigated. A loading by volume of 75% waste and 25% cement (or cement + slag) was used. The expression of pore solution was utilized to determine the chemical environment encountered by the waste species in the cement matrix. The highly alkaline conditions of ordinary Portland cement determined the stability of the metal species, with Cr being highly soluble. The replacement of 25% of the Portland cement by blast furnace slag was found to decrease the [OH-] of the pore solution resulting in a decrease of the Cr concentration. For cement wastes forms hydrated for 28 days, the Cr concentration decreased in the ...

1995-12-31

27

Waste form development. [Hydraulic cements, hydraulic cements with additives, polymer modified gypsum cement, thermosetting polymers  

Energy Technology Data Exchange (ETDEWEB)

In this program, contemporary solidification agents are being investigated relative to their applications to major fuel cycle and non-fuel cycle low-level waste (LLW) streams. Work is being conducted to determine the range of conditions under which these solidification agents can be applied to specific LLW streams. These studies are directed primarily towards defining operating parameters for both improved solidification of problem wastes and solidification of new LLW streams generated from advanced volume reduction technologies. Work is being conducted to measure relevant waste form properties. These data will be compiled and evaluated to demonstrate compliance with waste form performance and shallow land burial acceptance criteria and transportation requirements (both as they exist and as they are modified with time). 6 tables.

1982-01-01

28

Waste form development  

International Nuclear Information System (INIS)

In this program, contemporary solidification agents are being investigated relative to their applications to major fuel cycle and non-fuel cycle low-level waste (LLW) streams. Work is being conducted to determine the range of conditions under which these solidification agents can be applied to specific LLW streams. These studies are directed primarily towards defining operating parameters for both improved solidification of problem wastes and solidification of new LLW streams generated from advanced volume reduction technologies. Work is being conducted to measure relevant waste form properties. These data will be compiled and evaluated to demonstrate compliance with waste form performance and shallow land burial acceptance criteria and transportation requirements (both as they exist and as they are modified with time). 6 tables.

1986-09-22

30

Growth and reproduction of nematodes isolated from tap water; Suidosui kara bunrisareta senchurui no zoshoku tokusei  

Energy Technology Data Exchange (ETDEWEB)

This paper elucidates morphological characteristics, reproduction forms and ecological characteristics of Plectus sp. and Rhabditis sp. which are most frequently detected nematodes separated from tap water. The paper also discussed experimentally establishment of cultivating conditions for these nematodes, and behavior and reproduction characteristics of nematodes under widely ranging conditions of temperatures, bacteria concentrations and pH. Plectus sp. grows in hermaphroditic individuals, while Rhabditis sp. grows only in female. An LE culture medium can cultivate nematodes that appear in tap water, and is suitable for subculture of nematodes. Conditions of temperatures from 20{degree}C to 25{degree}C, pH and inoculated concentration of bacteria at 10{sup 8} cell {center_dot} ml{sup -1} are suitable for reproduction of Plectus sp. and Rhabditis sp. Plectus sp. and Rhabditis sp. prefer mild ...

1996-08-10

31

Adsorption based processes as alternative to common gas conditioning at underground storage facilities using Sorbead; Procedes bases sur l'adsorption comme solution de rechange dans le conditionnement du gaz dans des lieux de stockage souterrains a l'aide de Sorbead  

Energy Technology Data Exchange (ETDEWEB)

The European gas market is continuing to expand due to increased industrial, domestic and power generation demand. As a result of this demand, and the trend toward liberalization of the market, the need for storage of gas is also increasing. One key segment of the large scale storage of gas is underground storage, either in partially depleted gas or oil fields, naturally occurring caverns, aquifers and salt cavities. In most cases the gas produced after storage requires conditioning to meet the water of hydrocarbon dew point specification of the gas transmission system. For that reason export gas from storage will require gas conditioning in order to meet pipeline specifications. Adsorption as a feasible and reliable process will be presented in detail and especially in regards to hydrocarbon dew-pointing compared with other process options. (author)

2000-07-01

32

Volatile Organic Compound Formation in Waste Composting Processes  

Environmental Research Database

Objectives~%~ To quantify the volatile organic compound (VOC) emissions arising from the composting of a range of municipal and~%~ industrial wastes.~%~~%~ To relate the VOC emissions to the material being processed and the process conditions.~%~~%~ To confirm the findings of the above activites by monitoring full-scale composting operations.~%~~%~ To develop predictive models of VOC emissions in relation to waste feedstock and process conditions.~%~~%~ To produce guidance for plant designers, operators a [continued...]DescriptionA recent study of three composting plants undertaken for the Environment Agency has confirmed earlier work suggesting that waste composting can be a source of volatile organic compound (VOC) emissions. However, these experiments were restricted to garden and kitchen ...

2005-01-30

33

WASTE DISPOSAL IN SALT. I. THE HNO$sub 3$-NaCl REACTION  

Science.gov (United States)

The chemical reaction between nitric acid and sodium chloride was investigated in onder to provide preliminary information for subsequent studies on the interaction between simulated Purex waste solution and salt. The reaction is characterized by the production of chlorine and nitrosyl chloride and can be considered to be the same as the aqua regia reaction. Within the limits of the conditions imposed by the projected field studies, the acid concentration and temperature are the two parameters which control the extent of the interaction. (auth)

1960-10-01

34

Environmental assessment for the proposed effluent limitations guidelines, pretreatment standards, and new source performance standards for the centralized waste treatment industry  

Science.gov (United States)

This report assesses the water quality related benefits that would be expected if the US Environmental Protection Agency (EPA) adopts the proposed effluent limitations, guidelines and pretreatment standards for the Centralized Waste Treatment (CWT) Industry. EPA estimates that under baseline conditions 205 CWT facilities discharge approximately 5.22 million lbs/year of metal and organic pollutants.

1998-12-01

35

The national plan of fight against greenhouse effect; Le plan national de lutte contre l'effet de serre  

Energy Technology Data Exchange (ETDEWEB)

France has committed herself to keep in 2010 the same levels of greenhouse gas emissions as those of 1990, i.e. 144 millions of tons of carbon equivalent (MtCe). However, taking into account the existing pollution abatement measures and the measurements performed so far, the greenhouse gases level should reach 160 MtCe in 2010. Therefore, the inter-ministry commission on greenhouse effect decided on November 27, 1998 to elaborate a new national plan of fight against greenhouse effect. The elaboration of the new plan has fallen under the responsibility of the inter-ministry mission of greenhouse effect (MIES). The new plan was presented by the prime minister, L. Jospin, on January 19, 2000. This document summarises the content of the new plan: architecture (modalities of elaboration, content), measures for the reduction of greenhouse gas emissions (industry, transportation sector, buildings, agriculture-forestry, wastes valorization, development of renewable ...

2000-07-01

36

Defense Waste and Environmental Restoration Program Plan: Defense Waste Management Division  

Energy Technology Data Exchange (ETDEWEB)

The DEFENSE WASTE MANAGEMENT PROGRAM has been chartered by the Department of Energy (DOE) to receive, reduce, store, and maintain all radioactive defense waste generated by Hanford and received from offsite DOE contractors in a safe condition and in accordance with DOE and Westinghouse Hanford Company (WHC) standards. These activities are accomplished through the use of TRU retrievable storage sites, solid waste burial grounds, liquid waste storage tanks, capsule storage pools, and other low-level waste disposal methods. Continuous and/or periodic surveillance is maintained. Through the use of improved packaging methods, evaporator-crystallization and capsule production waste has been and continues to be put in a safe and economic storage condition pending future reprocessing or final disposition. For this Program Plan, ...

1988-09-01

37

Ambassade Des Etats-Unis Kinshasa, Congo - Accueil  

Science.gov (United States)

sur la médiatisation des élections Il s'est ouverte le 16 septembre 2011 à Matadi dans le Bas-Congo une formation sur la médiatisation des questions électorales,...

2011-10-13

38
39

Lessons drawn from the accidents occurred in the framework of conventional external radiotherapy;Lecons tirees des accidents survenus dans le cadre de la radiotherapie externe conventionnelle  

Energy Technology Data Exchange (ETDEWEB)

This study examines some radiation accidents occurred in the past. This information has been systematically assessed to get global lessons. The experience feedback shows that the most of accidents happened in certain conditions. These conditions can be distributed in four categories: 1- perception and vigilance in occupation: accidental exposure happened by lack of vigilance in details and lack of vigilance and perception; 2- procedures: accidental exposure happened following a lack of procedures or control that were not enough complete, not enough documented or not completely implemented; 3- training and understanding: accidental exposures happened because the personnel was not enough qualified and educated, did not get the general training nor the the necessary specialized training; 4- liabilities: accidental exposures happened following lacks and ambiguity in the definition of functions of the personnel and in the hierarchy liabilities. In ...

2009-12-15

40

Waste and dust utilisation in shaft furnaces  

Energy Technology Data Exchange (ETDEWEB)

Wastes and dusts from steel industry, non-ferrous metallurgy and other branches can be utilised e.g. in agglomeration processes (sintering, pelletising or briquetting) and by injection into shaft furnaces. This paper deals with the second way. Combustion and reduction behaviour of iron- and carbon-rich metallurgical dusts and sludges containing lead, zinc and alkali as well as other wastes with and without pulverised coal (PC) has been studied when injecting into shaft furnaces. Following shaft furnaces have been examined: blast furnace, cupola furnace, OxiCup furnace and imperial-smelting furnace. Investigations have been done at laboratory and industrial scale. Some dusts and wastes under certain conditions can be not only reused but can also improve combustion efficiency at the tuyeres as well as furnace performance and productivity.

2005-07-01

41

VVER technology: Czechs check out and choose bitumenisation  

International Nuclear Information System (INIS)

Bituminization has to be selected as the process for conditioning radioactive liquid wastes arising from the two VVER V-230 reactors being built at Temelin in the Czech Republic. In the process, a thin-film evaporator, operating at a waste-product temperature of 160"oC, evaporates all free water from the waste effluents. Remaining solids are homogeneously dispersed in a bitumen matrix which solidifies through natural cooling of the binder. The relative simplicity of the process reduces construction costs for on-line waste facilities and operating costs are less given the cheap basic material and simple maintenance. The reliability of the process has been demonstrated at Western reactors and reprocessing plants though adaptations have had to be made to accept VVER effluents. (UK).

1994-01-01

42

Corrosion studies of carbon steel under impinging jets of simulated slurries of neutralized current acid waste (NCAW) and neutralized cladding removal waste (NCRW)  

Energy Technology Data Exchange (ETDEWEB)

Plans for the disposal of radioactive liquid and solid wastes presently stored in double-shell tanks at the Hanford Site call for retrieval and processing of the waste to create forms suitable for permanent disposal. Waste will be retrieved from a tank using a submerged slurry pump in conjunction with one or more rotating slurry jet mixer pumps. Pacific Northwest Laboratory (PNL) has conducted tests using simulated waste slurries to assess the effects of a impinging slurry jet on the corrosion rate of the tank wall and floor, an action that could potentially compromise the tank's structural integrity. Corrosion processes were investigated on a laboratory scale with a simulated neutralized cladding removal waste (NCRW) slurry and in a subsequent test with simulated neutralized current acid waste (NCAW) slurry. The test slurries simulated the actual NCRW ...

1992-01-01

43

Corrosion studies of carbon steel under impinging jets of simulated slurries of neutralized current acid waste (NCAW) and neutralized cladding removal waste (NCRW)  

Energy Technology Data Exchange (ETDEWEB)

Plans for the disposal of radioactive liquid and solid wastes presently stored in double-shell tanks at the Hanford Site call for retrieval and processing of the waste to create forms suitable for permanent disposal. Waste will be retrieved from a tank using a submerged slurry pump in conjunction with one or more rotating slurry jet mixer pumps. Pacific Northwest Laboratory (PNL) has conducted tests using simulated waste slurries to assess the effects of a impinging slurry jet on the corrosion rate of the tank wall and floor, an action that could potentially compromise the tank`s structural integrity. Corrosion processes were investigated on a laboratory scale with a simulated neutralized cladding removal waste (NCRW) slurry and in a subsequent test with simulated neutralized current acid waste (NCAW) slurry. The test slurries simulated the actual NCRW and NCAW ...

1992-01-01

44

Combustion of refuse-derived fuels in grate and fluidised bed furnaces; Ersatzbrennstoffverbrennung in Rost- und Wirbelschichtoefen  

Energy Technology Data Exchange (ETDEWEB)

In addition to the goal of ensuring waste disposal, thermal waste treatment has always been aimed at the energy-efficient utilisation of wastes. Developments in waste management have led to an increase in high-calorific waste arisings. This is attributable to the use of mechanical-biological waste treatment as well as to segregated waste collection systems. High-calorific wastes are equivalent to fossil fuels in terms of their calorific content. Furthermore, they fulfil the legal requirements for conversion to energy. Another source of high-calorific wastes suitable for conversion to energy can be made available through the segregated disposal of industrial wastes, in many cases at low cost. These high-calorific fractions of varying origin and composition are referred to ...

2005-07-01

45

Evaluation of new corrosion-resistant superheater tubing in high-efficiency waste-to-energy plants  

Energy Technology Data Exchange (ETDEWEB)

Field corrosion tests were conducted on eight single tube materials and two welded overlay materials in three typical Japanese waste incineration plants in an effort to develop new corrosion-resistant superheater tubes capable of functioning efficiently under temperature and pressure conditions of 500 C and 100 kgf/cm{sup 2}-g in high-efficiency waste-to-energy (WTE) plants. Austenitic alloys containing higher concentrations of chromium, nickel, and molybdenum [Cr + Ni + Mo] showed excellent corrosion-resistant properties, and the new alloys JHN24 and HR30M showed good corrosion resistance. Different corrosion rates found in each of the three plants were explained by differences in operating conditions, such as gas temperature, concentration of molten salts resulting from chlorine (Cl) content of deposits, heavy metal (zinc oxide [ZnO] + lead oxide [PbO]) content, etc. It was confirmed that the ...

1998-07-01

46

Waste treatment process for removal of contaminants from aqueous, mixed-waste solutions using sequential chemical treatment and crossflow microfiltration, followed by dewatering  

Energy Technology Data Exchange (ETDEWEB)

In processes of this invention aqueous waste solutions containing a variety of mixed waste contaminants are treated to remove the contaminants by a sequential addition of chemicals and adsorption/ion exchange powdered materials to remove the contaminants including lead, cadmium, uranium, cesium-137, strontium-85/90, trichloroethylene and benzene, and impurities including iron and calcium. Staged conditioning of the waste solution produces a polydisperse system of size enlarged complexes of the contaminants in three distinct configurations: water-soluble metal complexes, insoluble metal precipitation complexes, and contaminant-bearing particles of ion exchange and adsorbent materials. The volume of the waste is reduced by separation of the polydisperse system by cross-flow microfiltration, followed by low-temperature evaporation and/or filter pressing. The water produced as filtrate ...

1994-01-01

47

Waste treatment process for removal of contaminants from aqueous, mixed-waste solutions using sequential chemical treatment and crossflow microfiltration, followed by dewatering  

Energy Technology Data Exchange (ETDEWEB)

In processes of this invention aqueous waste solutions containing a variety of mixed waste contaminants are treated to remove the contaminants by a sequential addition of chemicals and adsorption/ion exchange powdered materials to remove the contaminants including lead, cadmium, uranium, cesium-137, strontium-85/90, trichloroethylene and benzene, and impurities including iron and calcium. Staged conditioning of the waste solution produces a polydisperse system of size enlarged complexes of the contaminants in three distinct configurations: water-soluble metal complexes, insoluble metal precipitation complexes, and contaminant-bearing particles of ion exchange and adsorbent materials. The volume of the waste is reduced by separation of the polydisperse system by cross-flow microfiltration, followed by low-temperature evaporation and/or filter pressing. The water produced as filtrate ...

1994-11-22

48

Potential for erosion corrosion of SRS high level waste tanks  

Energy Technology Data Exchange (ETDEWEB)

SRS high-level radioactive waste tanks will not experience erosion corrosion to any significant degree during slurry pump operations. Erosion corrosion in carbon steel structures at reported pump discharge velocities is dominated by electrochemical (corrosion) processes. Interruption of those processes, as by the addition of corrosion inhibitors, sharply reduces the rate of metal loss from erosion corrosion. The well-inhibited SRS waste tanks have a near-zero general corrosion rate, and therefore will be essentially immune to erosion corrosion. The experimental data on carbon steel erosion corrosion most relevant to SRS operations was obtained at the Hanford Site on simulated Purex waste. A metal loss rate of 2.4 mils per year was measured at a temperature of 102 C and a slurry velocity comparable to calculated SRS slurry velocities on ground specimens of the same carbon steel used in SRS waste tanks. ...

1994-01-01

49

Laboratory for characterization of spent nuclear fuel and high/medium level radioactive waste. Experimental results and performances  

International Nuclear Information System (INIS)

During the phases of separation, treatment, conditioning and storage of radioactive waste, destructive and nondestructive methods for their characterization are needed. In order to satisfy this necessity, in the frame of the National Program of Research and Development, the 'Laboratory for characterization of spent nuclear fuel and high/medium level radioactive waste- LABORAD' was created. The purpose of the project was to accredit the analysis methods available in the laboratory, and also to develop new methods for the characterization of the radioactive waste. A special attention was paid to the high-level radioactive waste and spent nuclear fuel characterization that require special facilities for handling. These facilities (e.g. hot cells, remote handlers, transport container) are already available in our institute. Experimental results and performances obtained during ...

2009-05-27

50

Sorption of gold by activated charcoal from cyan-containing solutions of complex salt composition  

Energy Technology Data Exchange (ETDEWEB)

An evaluation was made of the effectiveness of the action of reagents used for cleaning cyan-containing waste water for conditioning of the overflow of copper concentrate thickners of the Belousovskiy enrichment before sorption extraction of gold by activated charcoal. It was established that conditioning of the overflow by iron sulfates (II), copper and zinc diminshes, and by hypochlorite increases the capacitance of the activated charcoal for gold.

1982-01-01

51

Thermophilic slurry-phase treatment of petroleum hydrocarbon waste sludges  

Energy Technology Data Exchange (ETDEWEB)

Chemoheterotrophic thermophilic bacteria were used to achieve enhanced hydrocarbon degradation during slurry-phase treatment of oily waste sludges from petroleum refinery operations. Aerobic and anaerobic bacterial cultures were examined under thermophilic conditions to assess the effects of mode of metabolism on the potential for petroleum hydrocarbon degradation. The study determined that both aerobic and anaerobic thermophilic bacteria are capable of growth on petroleum hydrocarbons. Thermophilic methanogenesis is feasible during the degradation of hydrocarbons when a strict anaerobic condition is achieved in a slurry bioreactor. Aerobic thermophilic bacteria achieved the largest apparent reduction in chemical oxygen demand, freon extractable oil, total and volatile solid,s and polycyclic aromatic hydrocarbons (PAHs) when treating oily waste sludges. The observed shift with time in the molecular ...

1995-12-31

52

Thermophilic slurry-phase treatment of petroleum hydrocarbon waste sludges  

International Nuclear Information System (INIS)

Chemoheterotrophic thermophilic bacteria were used to achieve enhanced hydrocarbon degradation during slurry-phase treatment of oily waste sludges from petroleum refinery operations. Aerobic and anaerobic bacterial cultures were examined under thermophilic conditions to assess the effects of mode of metabolism on the potential for petroleum hydrocarbon degradation. The study determined that both aerobic and anaerobic thermophilic bacteria are capable of growth on petroleum hydrocarbons. Thermophilic methanogenesis is feasible during the degradation of hydrocarbons when a strict anaerobic condition is achieved in a slurry bioreactor. Aerobic thermophilic bacteria achieved the largest apparent reduction in chemical oxygen demand, freon extractable oil, total and volatile solid,s and polycyclic aromatic hydrocarbons (PAHs) when treating oily waste sludges. The observed shift with time in the molecular ...

1995-04-24

53

Strontium removal from caustic carbonate waste solutions using carrier coprecipitation  

Energy Technology Data Exchange (ETDEWEB)

A carrier coprecipitation procedures has been developed for the removal of radioactive strontium from caustic liquid low-level waste (LLLW) generated at Oak Ridge National Laboratory. The two-step treatment process involves the addition of normal Sr (as SrCl{sub 2}) to the waste matrix, which is composed primarily of 0.3 M NaOH and 0.6 M Na{sub 2}CO{sub 3}. The active Sr equilibrates with the normal Sr carrier and coprecipitates as SrCO{sub 3} at pH 13. A liquid/solid separation is made before the pH of the supernate is reduced to pH 8 with sulfuric acid. During the neutralization step, the aluminum is the waste precipitates as Al(OH){sub 3}. Further Sr decontamination is achieved as traces of active Sr sorb to the Al(OH){sub 3} that precipitates during the neutralization step. A final liquid/solid separation is made at pH 8 to remove the sorbed active Sr. Maximum Sr decontamination of the LLLW is obtained when at least 50 ...

1994-12-31

54

Selection of melter systems for the DOE/Industrial Center for Waste Vitrification Research  

Energy Technology Data Exchange (ETDEWEB)

The EPA has designated vitrification as the best developed available technology for immobilization of High-Level Nuclear Waste. In a recent federal facilities compliance agreement between the EPA, the State of Washington, and the DOE, the DOE agreed to vitrify all of the Low Level Radioactive Waste resulting from processing of High Level Radioactive Waste stored at the Hanford Site. This is expected to result in the requirement of 100 ton per day Low Level Radioactive Waste melters. Thus, there is increased need for the rapid adaptation of commercial melter equipment to DOE`s needs. DOE has needed a facility where commercial pilot scale equipment could be operated on surrogate (non-radioactive) simulations of typical DOE waste streams. The DOE/Industry Center for Vitrification Research (Center) was established in 1992 at the Clemson University Department of Environmental Systems ...

1993-12-31

55

XPS/AES Study of Electrical and Chemical Properties of Pd/SiC Interface  

Science.gov (United States)

Silicon carbide (SiC) based electronic devices are of great importance for applications under the condition of high temperature, high power and high radiation. Schottky diodes of Palladium/SiC are good candidates for hydrogen and hydrocarbon gas sensors at elevated temperature. The detection sensibility of the diodes has been found heavily temperature dependent. In this work, the electrical and chemical properties of Pd/SiC Schottky contacts were studied by XPS and AES at different annealing temperatures. Schottky diodes were made by depositing ultra-thin palladium films onto a silicon carbide substrate. No significant change in the Schottky barrier height of the Pd/SiC contact was found in the temperature range of 300-673K. Palladium diffusion into SiC and the formation of palladium silicides were observed at room temperature and became significant at 300^oC and higher temperature. The mechanism of diffusion and reaction at the Pd/SiC interface will be discussed. ...

1997-11-01

56

Use of neutron activation analysis for the control of air pollution of Algiers; Utilisation de l'analyse par activation neutronique pour le controle de la pollution de l'air d'Alger  

Energy Technology Data Exchange (ETDEWEB)

The urban zone needs clean air to assure public health. To achieve this goal several filter samples were collected in different sites in Algiers city. Toxic elements such as: Na, Mg, Cl, Sc, Cr, Ti, V, Fe, Co, Cu, Zn, Se, Br, Ag, Sb, Ce, La, Hf, Ta and Hg have been measured in the filters using neutron activation analysis technique. Irradiation of filter samples and standards were carried out in Es-Salem reactor. The experimental procedure and the results are discussed. We noted during this work that the upper limit values for suspended dusts and the high concentrations for some toxic elements found are due to the weather conditions and intense road traffic around collecting sites. (authors)

2010-07-15

57

Self-lubricating performance and durability of ball bearings for the LE-7 liquid oxygen rocket-turbopump  

Energy Technology Data Exchange (ETDEWEB)

The durability of ball bearings, 32-mm- and 45-mm-bore, with a retainer or glass cloth-polytetrafluoroethylene (PTFE) laminate was tested under a high radial load at a speed of 20,000 rpm in LOX or LN2. The retainers were characterized as good self-lubricators because the abrasive glass-cloth fiber tips exposed on the retainer were chemicaly etched away with hydrofluoric acid (HF). During testing, the bearing-cartridge-acceleration was monitored to detect bearing damage. Testing in LOX for about 2.2 hr showed that excellent lubricating conditions were obtained for all bearings. Testing in LN2 for about 5.1 hr detected that the fatigue life of the bearing was about the same as the calculated B10 fatigue life. The HF chemical treatment resulted in a reacted fluoride-oxide material which remained in the etched part of the glass fiber. Several chemical products, particularly MgO, CaO, and CaCO3, enhanced adhesion of PTFE transfer film to the counterface, resulting in ...

1993-09-01

58

Plastic instability in an omega forming Ti-l5% Mo alloy  

International Nuclear Information System (INIS)

The plastic flow behavior of a #beta#-titanium alloy (Ti-15% Mo) was investigated over a wide range of temperatures and strain rates covering those conditions where the #omega#-phase forms dynamically. Portevin-Le Chatelier (PLC) effect was observed in this alloy at temperatures between 575 and 775 K at a strain rate of 1.31 x 10"-"4 s"-"1. The serrated flow behavior of this alloy could be suppressed by rendering the matrix #beta#-phase more stable against the #beta# to #omega# transformation. PLC bands formed in this alloy, studied at different levels of magnification using light, scanning electron and transmission electron microscopy, showed a high density of deformation bands within the macroscopic PLC band. The following mechanism of serrated flow is proposed; the load drop is ascribed to the sudden flow associated with the formation of deformation bands within which #omega#-particles were destroyed while the subsequent load rise results ...

59

Photocorrosion of passive films on titanium in sulfuric acid  

Energy Technology Data Exchange (ETDEWEB)

Passive films formed anodically on titanium (Ti) plates in 0.5 M sulfuric acid were corroded in aqueous solutions of H{sub 2}SO{sub 4} in the dark and under illumination of a 250-W mercury lamp. The corrosion depth was determined by calculating the thickness of the oxide layers from interference patterns of reflection spectra in the visible region. Corrosion was observed at pH {le} 3, with the corrosion rate increasing exponentially with decreasing pH and achieving a maximum value at pH {approximately} 1. Photocorrosion generally was quicker than corrosion occurring in the dark in all cases (i.e., open-circuit, short-circuit, bias conditions) and increased under anodic polarization of the oxide electrode together with the photocurrent. Corrosion occurring in the dark decreased very weakly under anodic polarization. Long-term corrosion experiments indicated the initial corrosion rate for a thick anodic oxide was higher than the later rates, ...

1995-03-01

60

Metal leaching and acid mine drainage in British Columbia; La lixiviation des metaux et le drainage acide en Colombie-Britannique  

Energy Technology Data Exchange (ETDEWEB)

This poster presentation dealt with a brief overview of the practices in effect in British Columbia related to metal leaching and acid mine drainage. The metals mined in the province include coal, gold, silver, copper, molybdenum, lead, and zinc. Some mines operate under the surface, while others are strip mines, etc. under a variety of climactic conditions and a host of different mining companies, such as Cominco, Placer Dome and Noranda. The primary objective is the prevention of negative environmental impacts on land and in the water. Salmon and other fish need to be protected. A secondary objective is the minimization of impacts on the biota, which requires a detailed study of ecological risks. The solution often lies in soil covering. To illustrate, the author described the situation at Huckleberry Mines Ltd. and the remedial action that was implemented, and discussed the results on the beavers. In conclusion, the author discussed the strategies implemented by ...

2000-07-01

61

Degradation of recalcitrant organic pollutants by mixed catalysts; Degradazione di inquinanti organici recalcitranti mediante catalizzatori misti  

Energy Technology Data Exchange (ETDEWEB)

The photodegradation of two well known recalcitrant compounds was studied. At this aim, a photosystem constituted by titanium dioxide and polyaniline, both immobilised in a PVC membrane, and a sunlight simulating irradiation source was used. The optimisation of the experimental conditions, ph, ionic strength and, when operating on soils, humic acid concentration, allowed the photodegradation of Paraquat at a nearly 100% extent, while, an oxidation by hypochlorite was needed to degrade cyanuric acid. [Italian] E' stata studiata la fotodegradazione di due composti notoriamente recalcitranti a questo tipo di rimozione. Con un sistema fotocatalitico costituito da biossido di titanio e polianilina immobilizzati in una membrana di PVC ed operando con luce solare simulata e' possibile, ottimizzando le condizioni sperimentali di pH, forza ionica e - operando su terreno - concentrazione di acidi umici, ottenere la degradazione del ...

2001-05-01

62

Structural acceptance criteria for the evaulation of existing double-shell waste storage tanks located at the Hanford site, Richland, Washington  

Energy Technology Data Exchange (ETDEWEB)

The structural acceptance criteria contained herein for the evaluation of existing underground double-shell waste storage tanks located at the Hanford Site is part of the Life Management/Aging Management Program of the Tank Waste Remediation System. The purpose of the overall life management program is to ensure that confinement of the waste is maintained over the required service life of the tanks. Characterization of the present condition of the tanks, understanding and characterization of potential degradation mechanisms, and development of tank structural acceptance criteria based on previous service and projected use are prerequisites to assessing tank integrity, to projecting the length of tank service, and to developing and applying prudent fixes or repairs. The criteria provided herein summarize the requirements for the analysis and structural qualification of the existing double-shell tanks for ...

1995-09-01

63

Mine stability evaluation of panel 1 during waste emplacement operations at WIPP  

Energy Technology Data Exchange (ETDEWEB)

The specific objectives of the work were defined by the Environmental Evaluation Group (EEG) as follows: (1) assess the stability of panel 1 during the proposed operation of waste emplacement; (2) estimate the amount of time before room closure would be expected to transfer rock loads to the waste packages. The work consisted of (1) an analysis of geotechnical data and a review of the Department of Energy`s (DOE) plans for waste emplacement in panel 1, (2) an evaluation of ground conditions based on data analysis and observations of changes in ground conditions since the first evaluation in 1993 (USBM 1993), and (3) preparation of a report and presentation of the results to EEG staff. Excluded from this study are radiological safety issues and policies. The study is based on data provided by DOE and Westinghouse Electric Corporation (operator of the site) and conversations with DOE ...

1998-07-01

64

Drying characteristics and nitrogen loss of biogas digestate during drying process  

Energy Technology Data Exchange (ETDEWEB)

The cost of transporting biogas digestate can be decreased by reducing its water content. However, the digestate emits volatile compounds during drying. This study investigated the drying behaviour and the change of digestate composition. Drying took place in a hybrid solar/waste-heat dryer that used solar energy as well as waste heat from a combined heat and power unit (CHP) and the exhaust air of a microturbine. The experiment involved the use of 60 t of liquid digestate. Climatic conditions were measured inside and outside the drying hall. Dry matter (DM) and organic dry matter (ODM) were also measured on a daily basis. In addition, the energy consumption of waste and solar heat were recorded and related to the quantity of dried feedstock. The total nitrogen, ammonium, phosphate, potassium oxide, magnesium oxide and calcium oxide in the digestate were subjected to chemical analysis before and after ...

2010-07-01

65

Thermal treatment of dusts from non ferrous metallurgical industries  

Energy Technology Data Exchange (ETDEWEB)

Three samples of dusts generated by the non ferrous metallurgical industries are treated between 200 and 800 degree centigree in controlled oxidizing and reducing atmospheres. The objective of this study is to recover the valuable metals from these wastes. The treatments of these solids under oxidizing conditions at 700 degree centigree are well adapted for two samples. The totality of valuable elements are concentrated in the treatments residues. The use of hydrogen at 600 degree centigree, permits the removal of up to 100 % of valuable metals contained in the treated industrial wastes. The recovery rate of valuable metals (Pb, Zn, Cu) as well as the Global Decontamination Factor are reported. (Author) 9 refs.

2000-07-01

66

The high level and long lived radioactive wastes; Les dechets radioactifs a haute activite et a vie longue  

Energy Technology Data Exchange (ETDEWEB)

This report presents the main conclusions of 15 years of researches managed by the CEA. This report is the preliminary version of the 2005 final report. It presents the main conclusions of the actions on the axis 1 and 3 of the law of the 30 December 1991. The synthesis report on the axis 1 concerns results obtained on the long lived radionuclides separation and transmutation in high level and long lived radioactive wastes. the synthesis report on the axis 3 presents results obtained by the processes of conditioning and of ground and underground long term storage. (A.L.B.)

2005-07-01

67

Uptake of cesium and strontium by crystalline silicotitanates from radioactive wastes  

British Library Electronic Table of Contents (United Kingdom)

Crystalline silicotitanate inorganic ion exchanger, with a sitinakite structure is candidate material for remediation of aqueous nuclear waste streams. The syntheses of crystalline silicotitanate (CST) and Nb-substituted crystalline silcotitanate (Nb-CST) were carried out under hydrothermal conditions and the products were characterized using techniques viz., XRD, SEM/EDS, DTA/TGA, surface area respectively. Batch experiments were carried out to study the kinetics of uptake of 137Cs and 90Sr, to estimate the decontamination factor (DF) values and distribution coefficients (K d) for the above synthesized CST and Nb-CST samples from actual radioactive waste solutions. The DF values for uptake of Cs and Sr by Nb-CST after 24?h of equilibration was 355 and 136 whereas for CST it was found to b...

2011-01-01

68

Composition, morphology, properties of coal fly ash microspheres and their application for conditioning liquid radioactive waste  

International Nuclear Information System (INIS)

Using methods of the Moessbauer spectroscopy, scanning electron microscopy, and thermodynamic analysis of phase formation in silicate multi-component melts, the detailed study of composition, morphology, and properties of fly ash microspheres resulting from combustion of three coals (Irsha-Borodinskii, Kuznetskii and Ekibastuzskii) was carried out. About 60 microspherical products with an iron content of 2-94 wt.% Fe_2O_3 were obtained. The ranges of microsphere composition, suitable for liquid radioactive waste solidification in the forms of iron phosphate (36-94 wt.% Fe_2O_3) and aluminosilicate (2-20 wt.% Fe_2O_3) ceramics were determined. The possibility of producing porous materials and specific microspherical sorbents, based on coal fly ash cenospheres and their application for mobilisation of liquid radioactive waste solidification was demonstrated. (author)

69

Processing of exhausted resins for Trino NPP,  

International Nuclear Information System (INIS)

Decomposition of organic compounds contained in the spent ion exchange resins is considered effective in reducing the waste volume. A system using the wet-oxidation process has been studied for the treatment of the spent resins stored at Trino Nuclear Power Plant owned by SOGIN. Compared with various processes for treating sludge and resin, the wet-oxidation system is rather simple and the process conditions are mild. Not contaminated ion exchange resin samples similar to those ones used in Trino NPP were processed by wet-oxidation and appropriate decomposition of the organic compounds was verified. After decomposition the residue can be solidified with cement for final disposal. When compared with direct solidification without decomposition, the number of waste packages can be significantly reduced. Additional measures for conditioning secondary waste products have also been ...

2009-10-12

70

Modeling of hydrologic conditions and solute movement in processed oil shale waste embankments under simulated climatic conditions  

Energy Technology Data Exchange (ETDEWEB)

Commercial development of oil shale resources will produce vast quantities of processed shale waste. The presence of potentially toxic trace elements, inorganic salts, and potentially toxic residual organic constitutents make the disposal of vast quantities of processed shale a potential environmental problem. To be environmentally acceptable, processed shale disposal must: result in a physically stable structure, prevent or minimize release of potentially toxic compounds, and provide an economically acceptable post-land use. Water is the common element underlying all factors important to the environmental stability of disposed solid waste. The leaching and transport of solubles by water in processed shale embankments may result in degradation of local surface and groundwater quality. The major purpose of this research is to physically model, study, and describe the redistribution and movement of water and percolates in lifts of disposed ...

1990-07-01

71

A study on the treatment of radioactive liquid wastes using synthetic by air intake system  

International Nuclear Information System (INIS)

In this study based on the mass transfer theory, experiments for the evaporation rates depending on various conditions were carried out through the operation of the existing Natural Evaporation Facility in KAERI. Evaporation media were made of the cotton and polyester. Air circulation in the facility was forced by exhausting fans. The evaporation rate and the decontamination factor were calculated by the result of experiment. The evaporation rate increased as the flow rate of air supply, the feed rate of liquid waste, and the temperature of supplied air increased. As for the humility of supplied air, the evaporation rate was getting higher as the humidity was getting lower. As the result of this study, operation conditions of the Natural Evaporation Facility are optimized as follows; The air temperature above 8C .deg., the air humidity below 70%, the air flow rate 1.14-1.47 m/sec, and the liquid waste ...

2003-11-27

72

The Principles of Radioactive Waste Management  

CERN Document Server

The Principles of Radioactive Waste Management

1995-01-01

73

Establishing a nationalsystem for radioactive waste management  

CERN Document Server

Establishing a nationalsystem for radioactive waste management

1995-01-01

74

Waste to energy technologies.  

Science.gov (United States)

No abstract prepared.

2010-04-01

75

COURSE D'ORIENTATION  

CERN Multimedia

  Le Club d’Orientation du CERN vous propose de venir participer à la cinquième étape de la coupe d’automne Genevoise. Celle-ci sera organisée samedi 16 octobre par le club de Lausanne-Jorat (Canton de Vaud). Un fléchage depuis le Mont-sur-Lausanne en direction de Cugy vous conduira au Chalet à Gobet. 5 circuits seront proposés sur la carte Le Flon. Les inscriptions et les départs se feront sur place de 13h à 15h. Il est prévu une initiation à 13h30 pour les débutants. Les deux dernières étapes de la coupe d’automne sont prévues pour vendredi 22 octobre au soir et samedi 23 octobre après-midi. Le Club d’Orientation du CERN Informations sur ...

2010-01-01

76

Nondestructive techniques for the control of conditioned radioactive wastes  

International Nuclear Information System (INIS)

The final product of the radwaste conditioning process must satisfy certain requirments and physico-chemical properties in order to assure its safe long-term behaviour. Of course, the foreseen quality assurance and quality control should be conducted by means of non-destructive techniques. This work presents an over-view of various applicable non-destructive methods of analysis, showing their fields of investigation in testing waste packages, together with some arising practical problems. The most promising methods, such as eddy current testing, ultrasonic testing, #gamma#-scanning, #gamma#-spectroscopy, neutron counting and computerized tomography, are treated more deeply and some applications are presented. Particular attention is devoted to the development of a device based on computerized tomography; its essential components are reported and some design problems are also discussed.

2005-09-01

77

Dose consequences from a postulated criticality occurring in a low-level waste disposal facility  

Energy Technology Data Exchange (ETDEWEB)

Evaluations were done to determine conditions that could permit nuclear criticality with fissile uranium in low-level waste (LLW) facilities and to estimate potential radiation exposures to personnel if there were such an accident. Simultaneous hydrogeochemical and nuclear criticality studies were done (1) to identity realistic scenarios for uranium migration and concentration increase at LLW disposal facilities, (2) to model groundwater transport of uranium and subsequent concentration via sorption or precipitation, (3) to evaluate the potential for nuclear criticality resulting from potential increases in uranium concentration over disposal limits, and (4) to estimate potential radiation exposures to personnel resulting from criticality consequences. This paper presents the details of the radiation exposure calculations relying on the conditions as determined from the preceding studies detailed in a cited reference.

1997-12-01

78

Decontamination factor of an incinerator for radioactive solid wastes  

International Nuclear Information System (INIS)

An incinerator for the treatment of low-level radioactive solid wastes was installed in Tokai Research Establishment, JAERI, 1966. The incinerator was equipped with a scrubber, cyclone, electrostatic precipitator and HEPA filter. The retention factor (R.F.) of the furnace as well as the decontamination factors (D.F.) of each dust collector were measured using "3"2P as a tracer under various conditions. It was found that the overall D.F. of the incinerator was improved by the increase of the temperature in the furnace, decrease of the off gas flowrate, increase of the charged voltage of the electrostatic precipitator and by the increase of the liquid gas ratio of the scrubber. The overall D.F. of the incinerator (including the R.F. in the furnace) on the standard operating conditions was 9.1x10"6. (auth.).

79

B Plant treatment, storage, and disposal (TSD) units inspection plan  

Energy Technology Data Exchange (ETDEWEB)

This inspection plan is written to meet the requirements of WAC 173-303 for operations of a TSD facility. Owners/operators of TSD facilities are required to inspection their facility and active waste management units to prevent and/or detect malfunctions, discharges and other conditions potentially hazardous to human health and the environment. A written plan detailing these inspection efforts must be maintained at the facility in accordance with Washington Administrative Code (WAC), Chapter 173-303, ``Dangerous Waste Regulations`` (WAC 173-303), a written inspection plan is required for the operation of a treatment, storage and disposal (TSD) facility and individual TSD units. B Plant is a permitted TSD facility currently operating under interim status with an approved Part A Permit. Various operational systems and locations within or under the control of B Plant have been permitted for waste ...

1996-04-26

80

Assessment of gas flammability in transuranic waste container  

Energy Technology Data Exchange (ETDEWEB)

The Safety Analysis Report for the TRUPACT-II Shipping Package [Transuranic Package Transporter-II (TRUPACT-II) SARP] set limits for gas generation rates, wattage limits, and flammable volatile organic compound (VOC) concentrations in transuranic (TRU) waste containers that would be shipped to the Waste Isolation Pilot Plant (WIPP). Based on existing headspace gas data for drums stored at the Idaho National Engineering Laboratory (INEL) and the Rocky Flats Environmental Technology Site (RFETS), over 30 percent of the contact-handled TRU waste drums contain flammable VOC concentrations greater than the limit. Additional requirements may be imposed for emplacement of waste in the WIPP facility. The conditional no-migration determination (NMD) for the test phase of the facility required that flame tests be performed if significant levels of flammable VOCs were present in TRU ...

1995-12-01

85

National Response Center Intro Page  

Science.gov (United States)

operations and defense, personnel misconduct (PM), law enforcement (LE), and counterintelligence (CI) investigations.- At any time, the USG may inspect and seize data stored on...

2011-02-28

86

Inventarisatie telematica-ontwikkelingen Natco (Inventory ...  

Science.gov (United States)

... In Nederland wordt het telewerken bevorderd door bet Nederlands Telewerk Forum, waarin zowel de overheid als verschillende industri~le ...

1998-05-01

87

Analyse Exploitatiekosten: Registratie, Beheersing en ...  

Science.gov (United States)

... Opbrengsten in LCC analyses: baten. bate n- lastenstelIselI bij de overheid ell baten le bepalen. " Onzekerheid in LCC analyses. ...

2007-10-01

88

Le leucodistrofie: aspetti clinici e quadri con Tomografia Computerizzata e con Risonanza Magnetica  

International Nuclear Information System (INIS)

Leukodystrophies are inherited white matter diseases due to abnormalities occurring in myelin synthesis and/or maintenance. The most common types of these rare childhood conditions are represented by adrenoleukodystrophy, metachromatic leukodystrophy, Canavan's, Alexander's, Krabbe's, and Pelizaeus-Merzbacher's diseases. Most of them are lethal during childhood, with the exception of the adrenoleukodystrophy-adrenomyeloneuropathy complex, which sometimes, during its early phases, may be cured with a dietary therapy. The aims of this paper are: 1) the description of inheritance factors, pathogenesis, pathological and clinical findings of each of the most frequent childhood leukodystrophies; 2) the description of the most common patterns of these conditions on CT and MR imaging; 3) the evaluation of the diagnostic capabilities of these two imaging techniques and the comparison of their results. Finally, some of the therapies suggested for the ...

1991-01-01

89

Waste Food Storage at Fortress Rocks  

Science.gov (United States)

... of waste food generated at McMurdo Station. Some of the difficulties of disposing of waste food ... change waste generation or management at the site? Yes. This will be a temporary waste management ...

90

BIBRA "t"r"a"d"e"m"a"r"k - the biological treatment of radioactive waste water  

International Nuclear Information System (INIS)

BIBRA "t"r"a"d"e"m"a"r"k, is the new bio-technological method developed in Gundremmingen for treating radioactive waste water, using bacteria in a process analogous to the long-established principle of communal sewage treatment plants. The method exploits the behaviour of the micro-organisms found there, to establish optimum adaptation of their population for decomposing the typical pollutants found in this washing water. This procedure is particularly suitable for nuclear engineering plants, because in such plants the waste water composition changes little so that the bacteria can achieve optimum adaptation to this waste water. The organic ingredients of the washing media are decomposed by introducing air. The advantage of the procedure is not only the significant reduction of the amount of waste material, but also enhanced efficiency of the cleaning process. The decontamination factor in Gundremmingen ...

1999-03-01

91

MIMO APP Receiver Processing with Performance-Determined Complexity  

CERN Document Server

Typical receiver processing, targeting always the best achievable bit error rate performance, can result in a waste of resources, especially, when the transmission conditions are such that the best performance is orders of magnitude better than the required. In this work, a processing framework is proposed which allows adjusting the processing requirements to the transmission conditions and the required bit error rate. It applies a-posteriori probability receivers operating over multiple-input multiple-output channels. It is demonstrated that significant complexity savings can be achieved both at the soft, sphere-decoder based detector and the channel decoder with only minor modifications.

2010-01-01

92

Clean Technology Application : Kupola Model Burner for Increasing the Performance of Spent Accu Recycle  

International Nuclear Information System (INIS)

Recycling of used battery for recovering lead done by either small household/small scale industries has been identified as a source of air pollution, especially by heavy metal (Pb). This condition give an adverse impact toward workers and societies. Technological aspect is one of the causal. The process apply an open system. Therefore, a lot of energy, as well as dust wasted to the air without prior treatment. For overcoming this condition, closed system by utilizing Cupola furnace will be offered as one of the alternatives clean technology application and to increase the recovering performance in order to set an effective and efficient result. (author)

2000-02-01

93

SLFP: A stochastic linear fractional programming approach for sustainable waste management.  

Science.gov (United States)

A stochastic linear fractional programming (SLFP) approach is developed for supporting sustainable municipal solid waste management under uncertainty. The SLFP method can solve ratio optimization problems associated with random information, where chance-constrained programming is integrated into a linear fractional programming framework. It has advantages in: (1) comparing objectives of two aspects, (2) reflecting system efficiency, (3) dealing with uncertainty expressed as probability distributions, and (4) providing optimal-ratio solutions under different system-reliability conditions. The method is applied to a case study of waste flow allocation within a municipal solid waste (MSW) management system. The obtained solutions are useful for identifying sustainable MSW management schemes with maximized system efficiency under various constraint-violation risks. The results indicate that SLFP can support ...

2011-09-01

94

Laboratory studies of gas generation and potential for tank wall corrosion during blending of high-level wastes at the West Valley Demonstration Project  

Energy Technology Data Exchange (ETDEWEB)

Laboratory experiments were conducted to simulate the transfer of acidic THOREX waste from Tank 8D-4 into the alkaline PUREX waste in Tank 8D-2 at West Valley. The purpose of the experiments was to explore means of minimizing the production of nitric oxide (NO) gas during mixing of the two wastes and to assess the potential for the gas to further react in the vapor space possibly leading to enhanced corrosion of the tank walls. Forty one THOREX/PUREX mixing tests were conducted to explore the effects of stirring rate, pH, THOREX addition rate, THOREX or PUREX dilution, and temperature. The two most important criteria for minimizing NO production were to maintain some degree of agitation and the keep the pH in the PUREX high, preferably >12. Steel corrosion tests were performed in the presence of low partial pressures of NO{sub 2} and liquid water or water vapor. The NO{sub 2} (from oxidation of NO in the vapor space) ...

1995-05-01

95

Evaluation of actinide biosorption by microorganisms  

Energy Technology Data Exchange (ETDEWEB)

Conventional methods for removing metals from aqueous solutions include chemical precipitation, chemical oxidation or reduction, ion exchange, reverse osmosis, electrochemical treatment and evaporation. The removal of radionuclides from aqueous waste streams has largely relied on ion exchange methods which can be prohibitively costly given increasingly stringent regulatory effluent limits. The use of microbial cells as biosorbants for heavy metals offers a potential alternative to existing methods for decontamination or recovery of heavy metals from a variety of industrial waste streams and contaminated ground waters. The toxicity and the extreme and variable conditions present in many radionuclide containing waste streams may preclude the use of living microorganisms and favor the use of non-living biomass for the removal of actinides from these waste streams. In the work presented ...

1996-06-01

96

Combustion of biodiesel fuel produced from hazelnut soapstock/waste sunflower oil mixture in a Diesel engine  

International Nuclear Information System (INIS)

Biodiesel is considered as an alternative fuel to Diesel fuel No. 2, which can be generally produced from different kinds of vegetable oils. Since the prices of edible vegetable oils are higher than that of Diesel fuel No. 2, waste vegetable oils and non-edible crude vegetable oils are preferred as potential low priced biodiesel sources. In addition, it is possible to use soapstock, a by-product of edible oil production, for cheap biodiesel production. In this study, a methyl ester biodiesel was produced from a hazelnut soapstock/waste sunflower oil mixture using methanol, sulphuric acid and sodium hydroxide in a two stage process. The effects of the methyl ester addition to Diesel No. 2 on the performance and emissions of a four cycle, four cylinder, turbocharged indirect injection (IDI) Diesel engine were examined at both full and partial loads. Experimental results showed that the hazelnut soapstock/waste sunflower oil ...

2005-03-01

97

The performance tests used the water scrubber for ruthenium rejection  

Energy Technology Data Exchange (ETDEWEB)

LEDF (Large Equipment Dismantling Facility) will be constructed for the purpose of decontaminating the high level {alpha} solid waste generated in oarai engineering center of JNC. And, main processing process of LEDF is incineration and melting system. LEDF will be intended to reduce the secondary waste that occurs along with the operation of the off gas processing equipment of incineration and melting system. It assumed that we are able to eliminate the adsorption tower using silica gel, if the decontamination factor to volatile ruthenium is able to expect in the packed scrubber that is established to remove harmful gas. Thereupon, we carried out this tests that eliminates the adsorption tower and reduces the secondary waste. The decontamination factor (DF) to the volatile ruthenium by the water scrubber is confirmed in the established institution which is in Tokai Works. However, decontamination factor differs and depends ...

2002-11-01

98

The performance tests used the water scrubber for ruthenium rejection  

International Nuclear Information System (INIS)

LEDF (Large Equipment Dismantling Facility) will be constructed for the purpose of decontaminating the high level #alpha# solid waste generated in oarai engineering center of JNC. And, main processing process of LEDF is incineration and melting system. LEDF will be intended to reduce the secondary waste that occurs along with the operation of the off gas processing equipment of incineration and melting system. It assumed that we are able to eliminate the adsorption tower using silica gel, if the decontamination factor to volatile ruthenium is able to expect in the packed scrubber that is established to remove harmful gas. Thereupon, we carried out this tests that eliminates the adsorption tower and reduces the secondary waste. The decontamination factor (DF) to the volatile ruthenium by the water scrubber is confirmed in the established institution which is in Tokai Works. However, decontamination factor differs and depends ...

99

Evaluation of value for hydrogen release from high-level liquid waste. 4. Hydrogen release rate for {gamma}-ray radiolysis of simulated purex waste solutions  

Energy Technology Data Exchange (ETDEWEB)

The rates of hydrogen release from simulated high-level liquid waste (SHLLW) during irradiation of {sup 60}Co {gamma}-rays have been studied using a laboratory-scale apparatus. The SHLLW used was made up of 28 different metal elements, the concentrations of which were determined from a computed data (ORIGEN-2) for a Purex spent fuel (burn-up of 4.5 GWd/t, cooling time of 4 years) except for those of corrosion products (Fe, Cr and Ni) and of chemical process additive (P). The nitrate ion concentration of the SHLLW was 4.97 M. The G-value of hydrogen release was 0.0164 for stirred conditions, but for nonstirred conditions with dose rate : 2.8 kGy/h and with the SHLLW solution height more than 8 cm, the following relation was found between the G-value and the solution height (d cm); G(H{sub 2}) = 0.100 d{sup -1.6}. The G-values of oxygen and nitrogen releases were also determined. (author)

1997-12-01

100

Evaluation of value for hydrogen release from high-level liquid waste. 4. Hydrogen release rate for #gamma#-ray radiolysis of simulated purex waste solutions  

International Nuclear Information System (INIS)

The rates of hydrogen release from simulated high-level liquid waste (SHLLW) during irradiation of "6"0Co #gamma#-rays have been studied using a laboratory-scale apparatus. The SHLLW used was made up of 28 different metal elements, the concentrations of which were determined from a computed data (ORIGEN-2) for a Purex spent fuel (burn-up of 4.5 GWd/t, cooling time of 4 years) except for those of corrosion products (Fe, Cr and Ni) and of chemical process additive (P). The nitrate ion concentration of the SHLLW was 4.97 M. The G-value of hydrogen release was 0.0164 for stirred conditions, but for nonstirred conditions with dose rate : 2.8 kGy/h and with the SHLLW solution height more than 8 cm, the following relation was found between the G-value and the solution height (d cm); G(H_2) = 0.100 d"-"1"."6. The G-values of oxygen and nitrogen releases were also determined. (author).

1997-01-01

101

Recycling of plastic packaging in Fredrikstad municipality. Climate accounts and other environmental factors; Kildesortering av plastemballasje i Fredrikstad kommune. Klimaregnskap og andre miljoefaktorer  

Energy Technology Data Exchange (ETDEWEB)

Oestfold Research has trough the project 'Climate accounts for disposal' for Waste Norway developed a model for calculation of net greenhouse gas emissions at the disposal of various waste types. The model is based on life cycle methodology according to the standard IS014044. This model has been used for plastic packaging in the project by adapting the basic values of specific conditions in the municipality of Fredrikstad. Oestfold Research has made an assessment of greenhouse gas emissions for the recycling and material recovery of plastic packaging from households in the district on assignment from Fredrikstad municipality and compared with the current solution where plastic packaging together with residual waste is used for energy utilisation. Based on the population in Fredrikstad and estimated amount of plastic packaging waste arising per household per year ...

2009-11-15

102

THE RECYCLING OF MIXTURES OF HEAVY METALS FROM WASTE USING ELECTRO- DEPOSITION  

Environmental Research Database

ObjectivesObjectives Not AvailableDescriptionWe will study the electrodeposition of metals from solutions containing a~%~ mixture of metal cations, in order to discover the conditions which lead to the separation of the metals. Measurements will be made both using small glass cells and using a more realistic size (10 cm x 10 cm electrodes) of electrodeposition cell.~%~

1996-01-31

103

Ocean disposal feasibility study: candidate DOE (FUSRAP) soil characterization. [Formerly Utilized Sites Remedial Action Program  

Energy Technology Data Exchange (ETDEWEB)

The Formerly Utilized Sites Remedial Action Program (FUSRAP) is to evaluate the radiological conditions at former MED-US AEC sites. Purpose of the Ocean FUSRAP program is to assess the feasibility of ocean disposal of FUSRAP waste which contains trace natural radioactive materials. This paper presents soil characterization information on the Middlesex, NJ, Sampling Plant site, and reports preliminary ocean dispersion calculations. (DLC)

1982-01-01

104

Performance Assessment Monitoring Plan for the Hanford Site Low-Level Burial Grounds  

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy Order 435.1, Radioactive Waste Management, requires a disposal authorization statement authorizing operation (or continued operation) for low-level waste disposal facilities. In fulfillment of these requirements, a disposal authorization statement was issued on October 25, 1999, authorizing the Hanford Site to transfer, receive, possess, and dispose of low-level radioactive waste at the 200 East Area burial grounds and the 200 West Area burial grounds. One of the conditions is that monitoring plans for the 200 East Area and 200 West Area low-level burial grounds be written and approved by the Richland Operations Office. As a result of a record of decision for the Hanford Site Solid Waste Program and acceptance of the Hanford Site Solid Waste Environmental Impact Statement, the use of the low-level burial ground (LLBG) as a disposal ...

2006-03-30

105

On the Metastable Level in Ni-like Ions  

Energy Technology Data Exchange (ETDEWEB)

The lowest excited level in Ni-like ions, 3d{sup 9}4s {sup 3}D{sub 3}, decays only via a magnetic octupole (M3) decay. They present calculated values of transition wavelengths and rates for ions with 30 {le} Z {le} 100. They have observed this line in Xe{sup 26+}, using the Livermore EBIT-I electron beam ion trap and a microcalorimeter, as well as a high-resolution flat-field grating spectrometer.

2004-09-14

106

Tests on decisive proof for the incinerating and melting facility using the in-can type high frequency induction heating  

Energy Technology Data Exchange (ETDEWEB)

LEDF(Large Equipment Dismantling Facility) is the solid waste processing technology development facility that carries out high-volume reduction and low dosage processing. The high-volume reduction processing of the high dose {alpha}-waste configured with combustible waste, pvc and rubber, spent ion exchange resin, and noncombustible waste have been planned the incinerating and melting facility using the in-can type high frequency induction heating in LEDF. This test is intended to clarify the design data. It was confirmed that the incinerating and melting performance, molten solid properties and exhaust gas processing performance with pilot testing equipment and bench scale equipment. The result of this test are as follows. 1. Processing speed is 6.7 kg/h for the combustible waste, 13.0 kg/h for the ion exchange resin, and 30.0 kg/h for the noncombustible waste. ...

1999-12-01

107

Malignant pulmonary lesion. Possible causes of CT misdiagnosis; Possibilita' di falsi negativi nella diagnosi delle neoplasie polmonari con Tomografia Computerzzata  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this work is to describe the radiological appearance of overlooked malignant pulmonary lesions at CT and to analyze the reasons of misdiagnosis. Ten patient with pulmonary lesion (PML) overlooked at forst CT examination were selected among patients with lung cancer. Endobronchial location of the tumors and their small size were the most frequent causes of misdiagnosis of PML at chest CT in the series. However, a systematic evaluation of CT scans can reduce the percentage of missed lesions. [Italian] Scopo del presente lavoro e' di descrivere le caratteristiche radiologiche delle lesioni polmonari maligne non identificate con la Tomografia Computerizzata (TC) e definire le possibili cause di errore. Sono stati esaminato 10 pazienti con tumore polmonare. Le sedi endobronchiale e centrale nonche' le piccole dimensioni delle lesioni polmonari maligne rappresentano ...

1999-06-01

108

World review of ozone forecasting methods and roles; Prevision des episodes d`ozone: etat de l`art dans le monde  

Energy Technology Data Exchange (ETDEWEB)

The growing concern of the population with regards to the problem of atmospheric pollution has induced a change in the role of air quality monitoring networks, especially those monitoring air pollution in large cities which suffer from summer smog. The population is no longer satisfied with real-time measurements but wants to be warmed of high pollutants concentrations in advance. Some countries have been forecasting air pollution, and especially ozone, for a large number of years. Although most of them use statistical models based on the analyses of past conditions which induced high pollution episodes, some predict ozone levels using only their knowledge of the meteorological situation. Nowadays two trends appear regarding ozone forecasting: either very basic statistical methods, such as regression, or more sophisticated ones, such as neural networks. The paper then reviews several behaviours common to most forecasting models: the uncertainly due to the great ...

1997-04-01

109

Pit lakes: their characteristics and the potential for their remediation  

Energy Technology Data Exchange (ETDEWEB)

Pit lakes form when open-pit mining operations are discontinued and dewatering ceases. The increase in open-pit metal mining since the 1970s will lead to the formation of numerous pit lakes over the next 50 years. Many of these lakes will develop acid sulfate conditions with high levels of dissolved metals. Approaches to remediation of these conditions that have been recommended include the addition of lime or other alkaline materials and the stimulation of sulfate-reducing bacteria. However, prevention rather than remediation is probably the preferable approach. Measures to prevent oxidation of mining waste and wall rocks, including measures to fill pits quickly with water, to inhibit the activity of acidophilic sulfur-oxidizing bacteria, and to promote anoxic conditions at the lake bottoms may minimize the formation of acids and dissolved metals. (orig.)

2000-10-01

110

Column leaching test to evaluate the use of alkaline industrial wastes to neutralize acid mine tailings  

Energy Technology Data Exchange (ETDEWEB)

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals that releases highly acidic, sulfate, and metals-rich drainage. In this study, alkaline industrial wastes were mixed with acid mine tailings in order to obtain neutral conditions. A series of column leaching tests were performed to evaluate the behavior of reactive mine tailings amended with alkaline-additions under dynamic conditions. Column tests were conducted of oxidized mine tailings combined with cement kiln dust, red mud bauxite, and mixtures of cement kiln dust with red mud bauxite. The pH results show the addition of 10% of alkaline materials permits the maintenance of near neutral conditions. In the presence of 10% alkaline material, the concentration of toxic metals such as Al, Cu, Fe, Zn are significantly reduced as well as the number of viable cells (Thiobacillus ferrooxidans) compared to ...

2005-08-01

111

Factors affecting public and political acceptance for the implementation of geological disposal  

International Nuclear Information System (INIS)

This publication identifies conditions which affect (either increase or decrease) public concern for and political acceptance of the development and implementation of programmes for geological disposal of long lived radioactive waste. It also looks at how interested citizens can be associated in the decision making process in such a way that their input enriches the outcome of a more socially robust and sustainable solution. The publication also considers how to optimize risk management, addressing the needs and expectations of the public and of other relevant stakeholders. Factors of relevance for societal acceptance conditions are identified for the different stages of a repository programme and implementation process, from policy development to the realization of the repository itself. Further, they are described and analysed through case studies from several countries, illustrating the added value of broadening the ...

2009-09-01

112

Status and strategies in radioactive waste management in the Russian Federation  

International Nuclear Information System (INIS)

Full text: There are following general tendencies linking to SNF and radioactive waste management (RWM) in the Russian nuclear industry now. The intention to use the closed nuclear fuel cycle based on power water reactors and fast reactor. The intensification of measures aimed at the solution of 'nuclear legacy' from defenses programs of USSR. The intention to improve the existing national RW management infrastructure in the near years by means of the creation of a centralized national system (including managing corporation responsible for operation of long-storage and disposal facilities of conditioned RW). The main aims radioactive waste management (RWM) in nuclear power plants (NPP) for the next 10-15 years are to equip all NPPs with the necessary set of facilities for conditioning of the stored and currently generated RW with packaging the end-product into containers, to build regional NPPs RW ...

113

Direct denitration and recycling of PFBR MOX liquid waste from dissolution test using microwave heating method  

International Nuclear Information System (INIS)

Full text: Dissolution test (DT) is one of the important specifications of PFBR MOX fuel. It is a macro homogeneity test used to ascertain that the dissolution of spent fuel will be easier during reprocessing. The DT specification limit for PFBR MOX fuel is ? 1.0 wt.% residue of the whole pellet when it is dissolved in HNO3 under reflux conditions. For this test, sintered MOX pellet is dissolved in reflux condition in 60 ml of 12M HNO3 for 10 hours. This test is carried out for each batch and during complete MOX campaign a lot of MOX waste in liquid form is being generated. This liquid waste is in clean form and U and Pu is required to be recovered from the clean waste. Different methods like direct denitration, precipitation and solvent extraction are available but either the product is not of good quality for pelletization or secondary liquid wastes are ...

2010-11-24

114

Waste treatment process for removal of contaminants from aqueous, mixed-waste solutions using sequential chemical treatment and crossflow microfiltration, followed by dewatering  

Energy Technology Data Exchange (ETDEWEB)

It is an object of the claimed invention to combine chemical treatment with microfiltration process to treat groundwater, leachate from contaminated soil washing, surface and run-off waters contaminated with toxic metals, radionuclides and trace amounts of organics from variety of sources. The process can also be used to treat effluents from industrial processes such as discharges associated with smelting, mining and refining operations. Influent contaminants amenable to treatment are from a few mg/L to hundreds of mg/L. By selecting appropriate precipitation, ion exchange and adsorption agents and conditions, efficiencies greater than 99.9 percent can be achieved for removal of contaminants. The filtered water for discharge can be targeted with either an order of magnitude greater or lower than contaminant levels for drinking water.

1992-12-31

115

The potential for use of waste-to-energy facility ash: Executive summary. Final report  

Energy Technology Data Exchange (ETDEWEB)

This executive summary presents an overview of the investigations, findings, conclusions, and recommendations of the Long Island Regional Planning Board (LIRPB) study of the Potential for Beneficial Use of Waste-to-Energy Facility Ash. The full report consists of the following volumes: Executive Summary; Volume 1: Long Island Ash Management Status; Volume 2: Sampling and Testing Procedures; Volume 3: Environmental Properties; Volume 4: Engineering Properties; Volume 5: Environmental Assessment; Volume 6: Engineering and Economic Evaluation; and Volume 7: Legal and Institutional Issues. Volumes one through seven are briefly summarized in this executive summary with the exception of Volume 2 of the report, which serves as the documentation of the sampling conditions and testing methods used in measuring chemical and physical properties of the ash tested. The study investigated the feasibility of the use of incinerator ash as a substitute for ...

1994-05-01

116

The influence of furnace geometry and wall materials on the combustion process and the prediction of problem areas in waste incinerators  

Energy Technology Data Exchange (ETDEWEB)

Based on the CFD-code FLUENT trademark, theoretical studies were conducted of the influences of incineration chamber geometry (direct, countercurrent and center flow) on the combustion process. The boundary conditions, e.g., the thermal input and the waste grate, were kept constant. Close attention was paid to the distribution of flow, spe-cies, and temperatures. In addition, the influence of a dis-placement body at the end of the combustion chamber was tested. The variation of different wall materials and the prediction of problem areas concerning corrosion, slagging, and contamination completed the studies. Close to the chamber walls, high CO-concentrations may indi-cate corrosion; particle flow may indicate where contami-nation, slagging or erosion could occur. (orig.)

2001-01-01

117

Pyro-chemistry within the FP7 ACSEPT Project-Program and Objective  

Energy Technology Data Exchange (ETDEWEB)

Actinide recycling by partitioning and transmutation is considered as one of the most promising strategies to reduce the inventory of radioactive waste, thus contributing to make nuclear energy sustainable. To make advances beyond the current state of the art in pyrochemical separations processes, the Domain 2 (DM2) of ACSEPT has been built on considering a process approach based on system studied. Four work packages that represent the main steps of a process block diagram have been identified: head-end steps, core process development, and salt treatment for recycling and waste conditioning. The results obtained in this domain will be integrated in DM 3 (Process) in order to orientate the R and D studies of DM2 and to propose and validate flowsheets at the end of the project. The state of the art on pyrochemical separation within the European Community and the working program of ACSEPT in pyrometallurgy are presented in ...

2008-07-01

118

Power generation from biomass residues using the gasifier/dual-fuel engine technique  

Energy Technology Data Exchange (ETDEWEB)

A process is described for converting organic waste into a combustible gas for use in a heavy duty thermal engine. The engines best suited for this operation are of the dual-fuel type whose output power results from the simultaneous work of 2 combustibles. The gas flow rate is controlled by the desired power output, while diesel fuel injection remains constant regardless of engine load. The low BTU gas produced by the gasification of dry wastes is a mixture of CO, H/sub 2/ CH/sub 4/, CO/sub 2/ and N/sub 2/. Diesel fuel savings under usual operating conditions is no less than 80% of the consumption of conventional diesel engines of identical power. Characteristics of the low Btu gas engines are described as are the characteristics of the gasifying equipment. Applications for this process are suggested. (DMC)

1980-01-01

119

Drying plant waste; Trocknung von Betriebsabfaellen  

Energy Technology Data Exchange (ETDEWEB)

Under the repository storage conditions of Eram and Konrad, waste packages designed for permanent storage must not contain or release freely mobile liquids, except for the minimum residues attainable by reasonable efforts or unavoidable. In accordance with a directive issued by the German Federal Ministry for the Environment (BMU), waste conditioning must be carried out so as to minimize waste volumes and, if possible, on the site where the waste arises. Liquid waste is conditioned most effectively by drying. At the present time, various different processes for drying liquid waste are employed as reflected by the state of the art: The Robe process; roller drying; the RDA process; Favorit; in-drum drying; and HPA liquid waste drying with make-up feed. The HPA process offers these ...

1995-11-01

120

Immobilization of waste material  

International Nuclear Information System (INIS)

A method is described for immobilizing or solidifying waste material, which includes blending the waste material with powdered metal and subjecting the mixture of waste material and powdered metal to high pressure. (author).

121

DISPOSING DEVICE FOR WASTE  

J-STORE (Japan)

Full Text Available

2005-12-19

122

Recycling of red mud waste for use as a catalyst for eliminating volatile organic compounds; Recyclage d'un dechet, une boue rouge, comme catalyseur pour l'elimination des composes organiques volatils  

Energy Technology Data Exchange (ETDEWEB)

Red mud is a waste product of the aluminium refining industry. It is composed of aluminium hydroxide and iron oxide. This study examined the feasibility of using red mud as a catalyst to eliminate volatile organic compounds in atmospheric pollutants. Volatile organic compounds can be eliminated by thermal oxidation between 600 and 1100 degrees C. However, the oxidation of volatile organic compounds can also be accomplished at lower temperatures (200 to 450 degrees C) if a catalyst is present. Currently, the low temperature destruction of volatile organic compounds is not widespread because of the difficulty in deactivating the catalyst. In this study, red mud was calcined in air at 500 degrees C. Under such conditions, the red mud converts to aluminium oxide and iron oxide. These 2 oxides are active and are carbon dioxide selective in the oxidation of volatile organic compounds. The study showed that red mud can be used as a catalyst for the ...

2005-08-01

123

Exhaust emissions from a Diesel engine fueled with transesterified waste olive oil  

Energy Technology Data Exchange (ETDEWEB)

The exhaust emissions of a Diesel direct injection Perkins engine fueled with waste olive oil methyl ester were studied at several steady-state operating conditions. Emissions were characterized with neat biodiesel from used olive oil and conventional Diesel fuel. Results revealed that the use of biodiesel resulted in lower emissions of CO (up to 58.9%), CO{sub 2} (up to 8.6%, excepting a case which presented a 7.4% increase), NO (up to 37.5%), and SO{sub 2} (up to 57.7%), with increase in emissions of NO{sub 2} (up to 81%, excepting a case which presented a slight reduction). Biodiesel also presented a slight increase in brake-specific fuel consumption (lower than 8.5%) that may be tolerated due to the exhaust emission benefits. Combustion efficiency remained constant using either biodiesel or Diesel fuel. The proposed alternative for Diesel fuel could significantly decrease the enormous amount of waste frying oil, ...

2003-07-01

124

ARIES-AT safety design and analysis  

Energy Technology Data Exchange (ETDEWEB)

ARIES-AT is a 1000 MWe conceptual fusion power plant design with a very low projected cost of electricity. The design contains many innovative features to improve both the physics and engineering performance of the system. From the safety and environmental perspective, there is greater depth to the overall analysis than in past ARIES studies. For ARIES-AT, the overall spectrum of off-normal events to be examined has been broadened. They include conventional loss of coolant and loss of flow events, an ex-vessel loss of coolant, and in-vessel off-normal events that mobilize in-vessel inventories (e.g., tritium and tokamak dust) and bypass primary confinement such as a loss of vacuum and an in-vessel loss of coolant with bypass. This broader examination of accidents improves the robustness of the design from the safety perspective and gives additional confidence that the facility can meet the no-evacuation requirement under average weather conditions. We also provide ...

2006-01-15

125

ARIES-AT safety design and analysis  

International Nuclear Information System (INIS)

ARIES-AT is a 1000 MWe conceptual fusion power plant design with a very low projected cost of electricity. The design contains many innovative features to improve both the physics and engineering performance of the system. From the safety and environmental perspective, there is greater depth to the overall analysis than in past ARIES studies. For ARIES-AT, the overall spectrum of off-normal events to be examined has been broadened. They include conventional loss of coolant and loss of flow events, an ex-vessel loss of coolant, and in-vessel off-normal events that mobilize in-vessel inventories (e.g., tritium and tokamak dust) and bypass primary confinement such as a loss of vacuum and an in-vessel loss of coolant with bypass. This broader examination of accidents improves the robustness of the design from the safety perspective and gives additional confidence that the facility can meet the no-evacuation requirement under average weather conditions. We also provide ...

2006-01-01

126

Multiple ordered phases in the filled skutterudite compound PrOs4As12  

Energy Technology Data Exchange (ETDEWEB)

Magnetization, specific heat, and electrical resistivity measurements were made on single crystals of the filled skutterudite compound PrOs{sub 4}As{sub 12}. Specific heat measurements indicate an electronic specific heat coefficient {gamma} {approx} 50-200 mJ/mol K{sup 2} at temperatures 10 K {le} T {le} 18 K, and {approx} 1 J/mol K{sup 2} for t {le} 1.6 K. Magnetization, specific heat, and electrical resistivity measurements reveal the presence of two, or possibly three, ordered phases at temperatures below {approx} 2.3 K and in fields below {approx} 3 T. The low temperature phase displays antiferromagnetic characteristics, while the nature of the ordering in the other phase(s) has yet to be determined.

2006-03-20

127

Calcified metastases of the kidney. Etiology, pathogenesis, CT findings and diagnostic problems; Metastasi renali calcificate: eziologia, patogenesi, aspetti con tomografia computerizzata e diagnostica differenziale  

Energy Technology Data Exchange (ETDEWEB)

Aim of the work was to describe computerised tomography (CT) findings of calcified renal metastases focusing on differential diagnosis problems. Abdominal CT scans of 8000 patients with tumor, performed from 1984 to 1998, have been retrospectively reviewed. [Italian] Scopo del lavoro e' quello di descrivere gli aspetti con tomografia computerizzata delle metastasi renali calcificate enfatizzando le problematiche diagnostico differenziali. Sono state valutate retrospettivamente le indagini TC addominali di 8000 pazienti affetti da tumore nel periodo 1984-1998, analizzando le lesioni calcificate riscontrate.

2000-03-01

128

The carbonate feedback system: interaction between stratigraphic accommodation, ecological succession and the carbonate factory; Le systeme de feed-back des carbonates: une interaction entre accomodation stratigraphique, succession ecologique et l`usine des carbonates  

Energy Technology Data Exchange (ETDEWEB)

In this paper, the analysis of carbonate depositional systems, using high resolution sequence stratigraphy, studies the ratio between change in accommodation space and skeletal carbonate production. This approach establishes the concurrent change in nature of facies belts (expansion, retraction and type) and fossil communities, within the detailed time frame in accommodation. Carbonate production is generally considered to be a fairly simple function of environmental conditions such as climate and water depth. However, data from several case studies also show a covariance between change in stratigraphic architecture of carbonate systems (the seaward or landward stepping stacking patterns of stratigraphic units) and charge in facies. Case studies include Carboniferous algal mound development in the Paradox Basin (USA), Devonian stromatoporoid reef development in Alberta (Canada), and Cenomanian rudistid shoal development in Oman. The hypotheses are tested on cases ...

1996-12-31

129

Test facilities for hybrid and electric drive trains; Stazione di prova sistemi di trazione ibridi ed elettrici  

Energy Technology Data Exchange (ETDEWEB)

ENEA (Italian National Agency for New Technologies, Energy and the Environment) is conducting a large research and development programme on innovative vehicles with high energy efficiency and low environmental impact. In particular conducts activities on electric and hybrid vehicles. Testing and evaluation activities play a strong role in this programme. A complete characterization chain has been then defined and set up with a network of facilities which covers main testing needs for single components, subsystems and complete vehicles, in simulated and real operating conditions. The test facility which has been realised is able to experiment and fully characterise complete drive-trains (and subsystems) for pure electric and hybrid vehicles. It is composed by a different section for each subsystem: 1) power generation; 2) energy storage and management; 3) driving motors. Each section acts as an experimental island, able to operate alone or jointly with the other ...

1998-12-31

130

PbZrO sub 3 -doped (Ba,Sr)TiO sub 3 -based dielectrics for high-voltage capacitor applications  

Energy Technology Data Exchange (ETDEWEB)

This paper reports that high-dielectric ceramics with the composition (94.7% {minus} x) (Ba,Sr)TiO{sub 3} + PbZrO{sub 3} + 5Bi{sub 2}Ti{sub 3}O{sub 9} + 0.3MnO{sub 2}, where the ration (Ba)/(Sr) = 1.25 and x {le} 15 mol%, have been developed for high-voltage capacitors. The dielectric constant of the ceramics is in the range 1200 to 1900 at room temperature, and the room-temperature dielectric loss, tan{delta}, is less than 0.3%, except when 15 mol% PbZrO{sub 3} is added with sintering at 1180{degrees}C to 1240{degrees}C for 2 h. Ceramics with more than 8 mol% zirconate show the Y5S characteristic of capacitance, and those with less than 8 mol% additive exhibit the Z5S characteristic. The dielectric constant gradually increases with increment in the ac signal voltage at 60 Hz, but decreases beyond a threshold value that varies with zirconate content and sintering conditions. The variation of the dielectric constant at 2 kVrms/mm (with respect ...

1991-11-01

131

European Commission - Environment  

Wastenet

...Species - see CITES Trade of Dangerous Chemicals Transport and Environment U Urban Environment Use of natural resources V Volatile Organic Compounds W Waste Landfills Waste electrical and electronic equipment - see WEEE Waste incineration Waste legislation - reporting Waste management planning Waste oils Waste shipments Waste water - see Urban waste water Water Bathing Water Drinking water Floods Marine environment Urban waste water Water Framework Directive WEEE - Waste Electric and Electronic Equipment Wildlife ...

132

Growth of Pinus radiada in soil containing solid waste from the kraft pulp industry  

Energy Technology Data Exchange (ETDEWEB)

The germination and growth of Pinus radials Don. plantlets in solid residues deriving from a Kraft pulp industry was evaluated. Plant conditions were monitored by histological studies of roots and shoot-tips, as well as by plant analyses of several essential and non essential elements. The solids employed consisted of ashes, fly-ashes, dregs, grits, primary sludge, brown stock screening rejects and various mixtures of them. Their addition, in a range of combinations to sandy/metamorphic or marine terrace/clay soils, resulted in effective and sustained growth under greenhouse conditions. Low proportions of wastes favored growth in most cases, indicating that they may act as fertilisers. In some experiments, especially in those where waste was added in proportions ranging from 50% to 60%, germination and/or development were slightly affected. Two-year old field experiments have confirmed that in spite of ...

2000-06-01

133

Evaluation of the suitability of the WIPP site  

Energy Technology Data Exchange (ETDEWEB)

Determination of the suitability of the site for WIPP is only the first major phase in the evaluation of the radiological impact of the repository on the public health and safety. The Environmental Evaluation Group (EEG) will continue to independently review the design of the facility, the operational procedures, the criteria for packaging and shipment of the waste, the plans, procedures and results of the WIPP experiments, emergency preparedness, adherence to EPA and pertinent NRC regulations, and other important features of the project. EEG has concluded from existing evidence that the Los Medanos site for the WIPP project has been characterized in sufficient detail to warrant confidence in the validation of the site for the permanent emplacement of approximately 6 million cubic feet of defense transuranic waste. This conclusion is based on the assumption that the maximum surface dose rate for the unshielded remote-handled transuranic ...

1983-05-01

134

Evaluation of new corrosion resistant superheater tubings in high efficiency waste-to-energy plants  

Energy Technology Data Exchange (ETDEWEB)

In order to develop new corrosion resistant superheater tubes capable of functioning efficiency under temperature and pressure conditions of 500 C and 100 ata used in high efficient waste-to-energy (WTE) plants, field corrosion tests were conducted on eight single tube materials and two welded overlay materials at metal temperatures of 450 C and 550 C for 700 and 3,000 hours, respectively, in three typical japanese waste incineration plants. The test results indicate that austenitic alloys containing higher concentrations of [Cr + Ni + Mo] show excellent corrosion resistant properties and new alloys of JHN24 and HR30M have good corrosion resistance. The different corrosion rate found for each of the three plants could be explained by differences in the severity of corrosion factors, such as, gas temperature, concentration of molten salts due to Cl content of deposits, and heavy metal [ZnO + PbO] content etc. It was also ...

1997-08-01

135

Obsidians and tektites: Natural analogues for water diffusion in nuclear waste glasses  

Energy Technology Data Exchange (ETDEWEB)

Projected scenarios for the proposed Yucca Mountain repository include significant periods of time when high relative humidity atmospheres will be present, thus the reaction processes of interest will include those known to occur under these conditions. The ideal natural analog for the proposed Yucca Mountain repository would consist of natural borosilicate glasses exposed to expected repository conditions for thousands of years; however, the prospects for identifying such an analog are remote, but an important caveat for using natural analog studies is to relate the reaction processes in the analog to those in the system of interest, rather than a strict comparison of the glass compositions. In lieu of this, identifying natural glasses that have reacted via reaction processes expected in the repository is the most attractive option. The goal of this study is to quantify molecular water diffusion in the natural analogs obsidian and tektites. ...

1991-11-01

136

Development program for magnetically assisted chemical separation: Evaluation of cesium removal from Hanford tank supernatant  

International Nuclear Information System (INIS)

Magnetic particles (MAG*SEP"S"M) coated with various absorbents were evaluated for the separation and recovery of low concentrations of cesium from nuclear waste solutions. The MAG*SEP"S"M particles were coated with (1) clinoptilolite, (2) transylvanian volcanic tuff, (3) resorcinol formaldehyde, and (4) crystalline silico-titanate, and then were contacted with a Hanford supernatant simulant. Particles coated with the crystalline silico-titanate were identified by Bradtec as having the highest capacity for cesium removal under the conditions tested (variation of pH, ionic strength, cesium concentration, and absorbent/solution ratio). The MAG*SEP"S"M particles coated with resorcinol formaldehyde had high distribution ratios values and could also be used to remove cesium from Hanford supernant simulant. Gamma irradiation studies were performed on the MAG*SEP"S"M particles with a gamma dose equivalent to 100 cycles of use. This irradiation ...

1994-05-09

137

Briquetting of self-reducing blendings of waste iron oxide mixtures. Final report  

Energy Technology Data Exchange (ETDEWEB)

The objectives of this project were to develop technologies to manufacture self-reducing briquettes out of waste iron oxides and to recycle them in an electric arc furnace or a cupola furnace. CRM has investigated and determined the optimal characteristics (binder, size, grain size, compositions and activator for the reduction reaction) for briquettes containing mixtures of mill scales, mill sludges, electric arc furnace (EAF) dust and coal as reduction agent. The goal of obtaining briquettes, in which iron oxides are totally reduced when these briquettes are loaded with the scrap into an electric arc furnace, was achieved. Trials at ProfilARBED have shown that it is possible to recycle mill and EAF by-products conditioned in self-reducing briquettes in an electric arc furnace without influence on the performance and on the environment. The iron content of the slag does not increase as the iron of the by-product is almost completely reduced. ...

2002-07-01

138

X-ray micro-spectroscopy: a tool for micro-scale radionuclide speciation in heterogeneous nuclear waste repository materials  

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: Large-scale problems such as nuclear waste disposal are increasingly recognized to be interconnected to small scale-mechanisms. Thus, synchrotron-based high-resolution analytical X-ray probes become important tools for exploring the micro-scale chemical reactivity of heterogeneous barrier materials used in nuclear waste repositories. In this study the layout of the micro-XAS beamline at the Swiss Light Source (SLS) will be presented. The beamline is optimized towards micro beam experiments ({approx}1 x 1 {mu}m{sup 2}) in the hard-X-ray regime (4 - {approx}22 keV) and allows to combine micro X-ray fluorescence (micro-XRF), micro X-ray absorption spectroscopy (micro- XAS), and micro X-ray diffraction (micro-XRD) investigations with radioactive samples. Furthermore, the potential of micro-XRF/XAS/XRD for acquiring spatially resolved molecular level information on the speciation and structural coordination ...

2005-07-01

139

Proceedings of a specialist meeting on regulatory approaches for the control of environmental residues containing naturally occurring radioactive material. Working material  

International Nuclear Information System (INIS)

Naturally occurring radionuclides are present in most material. The most common naturally occurring radionuclides in material are those of the uranium and thorium series and potassium-40. This material is commonly referred to as Naturally Occurring Radioactive Material (NORM). In some material the levels of naturally occurring radionuclides are significantly higher, to the extent that regulatory control may be required for radiation protection purposes. Regulation of NORM presents a range of new challenges for both regulators and operators. Unlike more traditional industries dealing with radionuclides, NORM industries have generally not had any radiological oversight and, for example, are not equipped for radiological monitoring. Some consumer goods containing NORM, which have not traditionally been considered as a radiological problem (such as some fertilizers), may require regulation and this may have social and economic consequences. The transport and disposal of NORM are also a ...

2002-09-23

140

The use of treated wastewater for chemlali olive tree irrigation: effects on soil properties, growth and oil quality  

Energy Technology Data Exchange (ETDEWEB)

Olive tree (Olea european L.) cultivation, the major tree crops in Mediterranean countries is being extended to irrigated lands. However, the limited water availability, the severe climatic conditions and the increased need for good water quality for urban and industrial sector uses are leading to the urgent use of less water qualities (brackish water and recycled wastewater) for olive tree irrigation. The aim of this work was to asses the effects of long term irrigation with treated waste water (TWW) on the soil chemical properties, on olive tree growth and on oil quality characteristics. (Author)

2009-07-01

141

Standardization/improvement and technical development of light water reactor power station in Japan(BWR)  

Energy Technology Data Exchange (ETDEWEB)

In order to realize improve of reliability and economy by duplicate production, rapid supply of repair parts from standardized storage, such were expected as to have continuous order of standardized plant, to ignore site condition, to avoid expansion of regulatory requirement. Standardization program was planned to limitedly promote standardization of safety-related design concept, major specification and basic system composition of reactor and primary systems. The area of standardization had been tried to expand to BOP such as general arrangement and rad-waste system.

1985-07-01

142

Scientific reference on the long time evolution of spent fuels; Referentiel scientifique sur l'evolution a long terme des combustibles uses  

Energy Technology Data Exchange (ETDEWEB)

This report is published in the framework of the 1991 French law for the nuclear waste management. The state of the art reported here concerns the long term evolution of spent fuel in the various environmental conditions corresponding to dry storage and geological disposal: closed system, air and water saturated medium. This review is based on the results of the french PRECCI project (Research Program on Long term Evolution of Spent Nuclear Fuel) and on literature data. (authors)

2005-03-15

143

Review on the status of solid radwaste management in Korean NPPs  

International Nuclear Information System (INIS)

To minimize the low and intermediate-level solid radwaste volume, the reduction efforts were persisted in Korean NPPs. As a result, annual average waste volumes were reduced to 194 drums per unit at last year. In this paper we confirmed 250 drums/unit-yr, EPRI URD management goal, and management condition for solid radwaste volume. Also, through the sample assessment of specific Korean NPP opened to the public, we could make sure that the prediction of saturation year for interim storage facility is fully suitable.

2003-10-01

144

Radiological performance assessment for the E-Area Vaults Disposal Facility  

Energy Technology Data Exchange (ETDEWEB)

This report is the first revision to ``Radiological Performance Assessment for the E-Area Vaults Disposal Facility, Revision 0'', which was issued in April 1994 and received conditional DOE approval in September 1994. The title of this report has been changed to conform to the current name of the facility. The revision incorporates improved groundwater modeling methodology, which includes a large data base of site specific geotechnical data, and special Analyses on disposal of cement-based wasteforms and naval wastes, issued after publication of Revision 0.

2000-04-11

145

NAME=\\  

Wastenet

...Publications Consultations Application forms Vacancies Contact us About us Air Climate change Flooding Live flood warnings Flood map How to use it About the ...map View the map FAQs Contact us & Feedback Flooding: who does what? Flood warning - what we do Floodline Warnings Direct Flood ...risk Being prepared FAQs Floodline kids Flooding publications External links Business & Flood Risk Seminar Contact us Land Planning Radioactive substances Waste Water ... You are here: Home Page Flooding Flood map View the map View the map: terms and conditions Important information about ...

146

Heat rejection system  

Energy Technology Data Exchange (ETDEWEB)

A cooling system for rejecting waste heat consists of a cooling tower incorporating a plurality of coolant tubes provided with cooling fins and each having a plurality of cooling channels therein, means for directing a heat exchange fluid from the power plant through less than the total number of cooling channels to cool the heat exchange fluid under normal ambient temperature conditions, means for directing water through the remaining cooling channels whenever the ambient temperature rises above the temperature at which dry cooling of the heat exchange fluid is sufficient and means for cooling the water. 5 figs.

1980-01-22

147

A two-cycle process for enhanced actinide separation from radioactive liquid wastes  

Energy Technology Data Exchange (ETDEWEB)

A two-cycle process using O{Phi}CMPO and HDEHP as extractants to achieve an alpha decontamination factor of HLLW greater than 10{sup 3} together with a reduction of the lanthanides/americium weight ratio by a factor of about 200 is considered. Experimentally measured distribution ratios have been employed as input data of a suitable computer code to define operating conditions and M/S stage numbers of a process flow-sheet able to meet the above-mentioned objectives.

1996-09-01

148

Coupled effects of the precipitation of secondary species on the mechanical behaviour and chemical degradation of concretes; Les effets couples de la precipitation d'especes secondaires sur le comportement mecanique et la degradation chimique des betons  

Energy Technology Data Exchange (ETDEWEB)

Sulfate attack of cement-based materials remains an important problem for the durability assessment of containers and disposal engineering barriers dedicated to the long-term storage of radioactive wastes since underground water which may reach these elements contains small quantities of sulfates (7-31 mmol/1). This work contributes to the study of sulfate-induced damage mechanisms, to their understanding and modelling. The experimental phases of this study aimed at the understanding of the different physico-chemical phenomena involved during an external sulfate attack at following their evolution and their impact on the transport and mechanical properties of the material. Leaching experiments in pure water and in a solution of sodium sulfate (with a sulfate content of 15 mmol/1), have been performed simultaneously on OPC paste (w/c 0,4)in order to allow a comparison of test results. The frequent analysis of the leachant has shown a consumption of sulfate ions by ...

2002-06-01

149

A.C.R.O. activity report 2003; A.C.R.O. rapport d'activite 2003  

Energy Technology Data Exchange (ETDEWEB)

A.C.R.O. (Association pour le Controle de la Radioactivite dans l'Ouest) is a French non governmental organisation that operates a laboratory for radioactivity analysis. It was created in 1986 as a response to people demands for information and reliable, independent testing. The organisation mainly carries out missions of information and training for its correspondents and more generally for a wide audience, particularly for people who worry about problems of environment, health, management of radioactive waste and emissions. Thanks to its structure, it enables citizens to involve themselves together with scientists so as to gain access to information that was hither to reserved to specialists. The organisation can vouchsafe its independence from the diversity of its members and volunteers, as well as from the diversity of its money resources. Besides its headquarters situated on the city of Caen area (Normandy), three branches ...

2003-07-01

150

Computed Tomography of the diabetic kidney; La Tomografia Computerizzata nello studio del rene diabetico  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this work is to investigate whether any morphometric or densitometric are detectable in the kidneys of type 2 diabetic patients. 40 diabetic patients were examined and of 20 non-diabetics (the control group) were submitted to triphasic helical CT for different abdominal conditions. The type 2 diabetic patients were 23 men and 17 women, mean age 62 years, while the nondiabetic controls were 12 men and 8 women, mean age 58 years. All the CT images were analyzed using the Multiplanar Reconstruction (MPR) software. It was evaluated morphometric features, such as the presence of parenchymal or vascular calcifications, axial and coronal renal diameters, coronal renal area, and cortico medullary ratio, and densitometric and functional features, such as unenhanced renal density, cortical and medullary density in the arterial phase, parenchymal density in the nephrographic phase, and contrast elimination. It was also compared the results in the subgroups of ...

2000-02-01

151

Approximate MIMO Iterative Processing with Adjustable Complexity Requirements  

CERN Document Server

Targeting always the best achievable bit error rate (BER) performance in iterative receivers operating over multiple-input multiple-output (MIMO) channels may result in significant waste of resources, especially when the achievable BER is orders of magnitude better than the target performance (e.g., under good channel conditions and at high signal-to-noise ratio (SNR)). In contrast to the typical iterative schemes, a practical iterative decoding framework that approximates the soft-information exchange is proposed which allows reduced complexity sphere and channel decoding, adjustable to the transmission conditions and the required bit error rate. With the proposed approximate soft information exchange the performance of the exact soft information can still be reached with significant complexity gains.

2011-01-01

152

In situ corrosion studies on selected high level waste packaging materials under simulated disposal conditions in rock salt formations  

International Nuclear Information System (INIS)

This paper reports about in-situ corrosion studies on selected materials for long-term resistant high-level waste (HLW) packagings acting as a barrier in a rock salt repository. The materials (Ti 99.8-Pd, Hastelloy C4 and five iron-base materials) were investigated in heated boreholes in the Asse salt mine under simulated HLW disposal conditions prevailing in normal operation of repository and in certain accident scenarios. The experiments under normal operating conditions were performed at temperatures of 120 deg. C to 210 deg. C (vertical temperature profile in the boreholes) without and with gamma irradiation (3#centre dot#10"2 Gy/h, Co-60 source) within the framework of the German/US Brine Migration Test. In these experiments only small amounts of migrated brine inclusions (NaCl-rich) from the rock salt were present as corrosion medium. In the experiments carried out under simulated accident ...

1993-02-01

153

lib_general.pro - ECCO2  

Science.gov (United States)

Returns singular values (sigma), ;left field (x) vectors, ..... n) do begin point=ngbrs(i) if (point+tau le nt-1) then begin if (x(point+tau,0) ne q) then .... ;FILTER ;applies a gaussian filter in the frequency domain function filter, x ...

154

an expert system for estimating forest harvesting productivity and cost  

Science.gov (United States)

Sep 1, 2011 ... Title: THINEX - an expert system for estimating forest harvesting productivity and cost. Author: LeDoux, C. B.; Gopalakrishnan, B.; Pabba, R. S. ...

155

When and how to reactivate the activated charcoal?; Quand et comment regenerer le charbon actif?  

Energy Technology Data Exchange (ETDEWEB)

The activated charcoal is very appreciates for the water treatment. It do not generate by-product of treatment. In return it is saturated after some time and may releases pollutant compounds. When and how to get to its regeneration?.

2000-03-01

156

System Design and Applications of the Ultra Small ... - GLTRS - NASA  

Science.gov (United States)

The advanced technologies of Ka-Band systems such as high gain spot .... sometimes used based on link requirements for a specific application. .... received at NASA LeRC from a Ku-band satellite and retransmitted to the USAT at Ka-Band. .... and to the Office of Management and Budget, Paperwork Reduction Project ...

157

Speech Communication in Noise  

Science.gov (United States)

... Un jeu de DVD créés à partir de boucles de bruit sur bande audionumérique ont été étalonnés de manière à produire le même spectre de bruit ...

2008-05-13

158

Multicentre, randomised, controlled study of the impact of continuous sub-cutaneous glucose monitoring (GlucoDay) on glycaemic control in type 1 and type 2 diabetes patients  

British Library Electronic Table of Contents (United Kingdom)

ResumeObjectif determiner dans une etude randomisee l'impact d'un enregistrement continu du glucose sous-cutane pendant 48 heures sur le controle glycemique trois mois plus tard chez des patients presentant un diabete de type 1 (DT1) ou de type 2 (DT2). Methodes Quarante-huit patients avec un mauvais equilibre glycemique (HbA1c : 8-10,5 %) ont beneficie d'un enregistrement continu du glucose sous-cutane pendant 48 heures avec le systeme GlucoDay (A. Menarini Diagnostics) et ont ete randomises en deux groupes : ajustement de traitement en fonction de l'autosurveillance glycemique capillaire (groupe ASG) ou du profil d'enregistrement continu du glucose sous-cutane (groupe CGM). Le dosage d'HbA1c et le port du GlucoDay ont ete renouveles trois mois plus tard. Resultats Trente-quatre patients ...

2009-01-01

159

Flies In Space - Drosophila - NASA Quest  

Science.gov (United States)

Aqu? va a poder aprender acerca de la Dros?fila Melanogaster, a la cual se le conoce como la mosca de la fruta! Usted podr?. Interpretar por qu? las moscas ...

160

Feynman lectures on physics, quantum mechanics; Le cours de physique de Feynman mecanique quantique  

Energy Technology Data Exchange (ETDEWEB)

This course is based upon lectures in physics given by Professor Feynman at the California institute of technology during 1961 and 1962. This volume is dedicated to quantum physics, semiconductors, symmetry and advanced principles of physics.

2000-07-01

162

CASE FI LE COPY - NASA Technical Reports Server  

Science.gov (United States)

1.9312. 1"6898. 1,3036 .7846 .313g .0121. Bright hess values. 263.291. 332.278. 382.911. 481.013. 575"949. 693.038. 886.076. 1025.316. 1291.139 ...

163

A Reproduced Copy - NASA Technical Report Server (NTRS)  

Science.gov (United States)

Ccna othf>r projecto, for c~le, on cl~te ZL.')d focxl syute:s in "cxico AIld. IndiA and on idantification of cli=atn-aono!tivG ~cctora, ...

164

STRESS CORROSION CRACKING SUSCEPTIBILITY OF HIGH LEVEL WASTE TANKS DURING SLUDGE MASS REDUCTION  

Energy Technology Data Exchange (ETDEWEB)

Aluminum is a principal element in alkaline nuclear sludge waste stored in high level waste (HLW) tanks at the Savannah River Site. The mass of sludge in a HLW tank can be reduced through the caustic leaching of aluminum, i.e. converting aluminum oxides (gibbsite) and oxide-hydroxides (boehmite) into soluble hydroxides through reaction with a hot caustic solution. The temperature limits outlined by the chemistry control program for HLW tanks to prevent caustic stress corrosion cracking (CSCC) in concentrated hydroxide solutions will potentially be exceeded during the sludge mass reduction (SMR) campaign. Corrosion testing was performed to determine the potential for CSCC under expected conditions. The experimental test program, developed based upon previous test results and expected conditions during the current SMR campaign, consisted of electrochemical and mechanical testing to determine the ...

2007-10-18

165

Development of surface decontamination technology for radioactive waste using plasma. Summary of decontamination performance in dry surface decontamination technology with low-pressure arc plasma  

International Nuclear Information System (INIS)

Various kinds of decontaminations are carried out in atomic power plant. Here current decontamination technologies such as chemical decontamination with chemical solution or blast decontamination have a problem of reduction of secondary radioactive waste generated in the decontamination process. On the other hand, a low pressure arc plasma can remove metal oxide film on the metal substrate without heavy damage on the metal substrate when the object to be treated was set as a cathode. Dry surface decontamination technology with using low-pressure arc plasma can decrease secondary radioactive waste because low-pressure arc plasma does not need any chemical solution. In addition, the time required for treatment can be shorter, so it is possible for the low-pressure arc plasma decontamination technology to interpolate the current decontamination technologies such as spot decontamination technology etc. Therefore we have been investigating the ...

2008-12-01

166

A study on the treatment of radioactive liquid wastes using synthetic by air intake system  

Energy Technology Data Exchange (ETDEWEB)

In this study based on the mass transfer theory, experiments for the evaporation rates depending on various conditions were carried out through the operation of the existing Natural Evaporation Facility in KAERI. Evaporation media were made of the cotton and polyester. Air circulation in the facility was forced by exhausting fans. The evaporation rate and the decontamination factor were calculated by the result of experiment. The evaporation rate increased as the flow rate of air supply, the feed rate of liquid waste, and the temperature of supplied air increased. As for the humility of supplied air, the evaporation rate was getting higher as the humidity was getting lower. As the result of this study, operation conditions of the Natural Evaporation Facility are optimized as follows; The air temperature above 8C .deg., the air humidity below 70%, the air flow rate 1.14-1.47 m/sec, and the liquid waste ...

2003-07-01

167

A desiccant dehumidifier for electric vehicle heating  

Energy Technology Data Exchange (ETDEWEB)

Vehicle heating requires a substantial amount of energy. Engines in conventional cars produce enough waste heat to provide comfort heating and defogging/defrosting, even under very extreme conditions. Electric vehicles (EVs), however, generate little waste heat. Using battery energy for heating may consume a substantial fraction of the energy storage capacity, reducing the vehicle range, which is one of the most important parameters in determining EV acceptability. Water vapor generated by the vehicle passengers is in large part responsible for the high heating loads existing in vehicles. In cold climates, the generation of water vapor inside the car may result in water condensation on the windows, diminishing visibility. Two strategies are commonly used to avoid condensation on windows: windows are kept warm, and a large amount of ambient air is introduced in the vehicle. Either strategy results in a substantial heating ...

1996-09-01

168

Subsurface Injection of Liquid Waste  

Science.gov (United States)

... Other Sources Toxics Intranet Subsurface Injection of Liquid Waste -- Florida Surface features of a typical...

170

Radiation protection and the management of radioactive waste in the oil and gas industry  

CERN Document Server

Radiation protection and the management of radioactive waste in the oil and gas industry

2003-01-01

172

On-site burning, remote camp  

Science.gov (United States)

... wood, kitchen wastes, and human faeces. The ash from such waste burning shall be deposited and ...

173

Liquid Radioactive Wastes Processing  

International Science & Technology Center (ISTC)

Methods of Decontamination, Utilization, and Deactivation of Liquid Radioactive Wastes

174

IEE, accelerated waste mgt, McM  

Science.gov (United States)

... in ATCM Recommendation XIV-2. The USAP's materials and waste management efforts are consistent with ...

175

Human Waste Handling-Kooyman  

Science.gov (United States)

... wood, kitchen wastes, and human faeces with the ash from such burning deposited and retained in an ...

176

Dioxins in the Baltic sea  

Wastenet

for municipal waste iron ore sinter plants incinerators for clinical waste facilities of the non-ferrous metal

177

Combustion of Crop Production Wastes  

International Science & Technology Center (ISTC)

Development, Investigation and Improvement of a System of Incinerating Crop Production Wastes in Small Capacity Boilers

179

A Grafcet-based expert system for process control; Un systeme expert base sur le Grafcet pour le controle de procede  

Energy Technology Data Exchange (ETDEWEB)

This article describes a hierarchical and functional model for continuous process control aid. The expertise is represented by graphs from a simple functional restructuring of the Grafcet, which is the formalism used by the designers of the command-control program. The new structure is familiar to the operator, and it is settled in an expert system. The application built on the basis of this method detects some default types which are not detected by the control-command. It proposes a diagnosis to the operator, and can explain and justify the state of the process. (authors) 9 refs.

1997-11-01

180

Transuranic contaminated waste form characterization and data base  

Energy Technology Data Exchange (ETDEWEB)

This volume contains 5 appendices. Title listing are: technologies for recovery of transuranics; nondestructive assay of TRU contaminated wastes; miscellaneous waste characteristics; acceptance criteria for TRU waste; and TRU waste treatment technologies.

1980-07-01

181

Process Waste Assessment for inorganic solid waste and empty containers <30 gallons  

Energy Technology Data Exchange (ETDEWEB)

This Process Waste Assessment was conducted to evaluate the two largest hazardous waste streams generated on-site at Sandia National Laboratory (SNL)/California -- ``Other Inorganic Solid Waste`` and ``Empty Containers <30 Gallons.``

1993-12-01

182

Waste management units - Savannah River Site. Volume 1, Waste management unit worksheets  

Energy Technology Data Exchange (ETDEWEB)

This report is a compilation of worksheets from the waste management units of Savannah River Plant. Information is presented on the following: Solid Waste Management Units having received hazardous waste or hazardous constituents with a known release to the environment; Solid Waste Management Units having received hazardous waste or hazardous constituents with no known release to the environment; Solid Waste Management Units having received no hazardous waste or hazardous constituents; Waste Management Units having received source; and special nuclear, or byproduct material only.

1989-10-01

183

A.C.R.O. activity report 2002; A.C.R.O. rapport d'activite 2002  

Energy Technology Data Exchange (ETDEWEB)

A.C.R.O. (Association pour le Controle de la Radioactivite dans l Ouest) is a French non governmental organisation that operates a laboratory for radioactivity analysis. It was created in 1986 as a response to people demands for information and reliable, independent testing. The organisation mainly carries out missions of information and training for its correspondents and more generally for a wide audience, particularly for people who worry about problems of environment, health, management of radioactive waste and emissions. Thanks to its structure, it enables citizens to involve themselves together with scientists so as to gain access to information that was hither to reserved to specialists. The organisation can vouchsafe its independence from the diversity of its members and volunteers, as well as from the diversity of its money resources. Besides its headquarters situated on the city of Caen area (Normandy), three branches situated in ...

2002-07-01

184

Fundamental Chemistry And Thermodynamics Of Hydrothermal Oxidation Processes  

Science.gov (United States)

Hydrothermal oxidation (HTO) is a promising technology for the treatment of aqueous-fluid hazardous and mixed waste streams. Waste streams identified as likely candidates for treatment by this technology are primarily aqueous fluids containing hazardous organic compounds, and often containing inorganic compounds including radioisotopes (mixed wastes). These wastes are difficult and expensive to treat by conventional technologies (e.g. incineration) due to their high water content; in addition, incineration can lead to concerns related to stack releases. An especially attractive potential advantage of HTO over conventional treatment methods is the total containment of all reaction products within the overall system. The potential application of hydrothermal oxidation (HTO) technology for the treatment of DOE hazardous or mixed wastes has been uncertain due to concerns about safe and ...

2001-12-31

185

Waste management at Los Alamos: Protecting our environment  

Energy Technology Data Exchange (ETDEWEB)

This report consists of a broad overview of activities at Los Alamos National Laboratory (LANL). The following topics are discussed: The growth of the waste management group; what we do today; the mission of the waste management group; the liquid waste treatment section; the radioactive liquid waste project office; the chemical waste section; the radioactive waste section; and the technical support section.

1993-11-01

186

Radioactive waste  

Energy Technology Data Exchange (ETDEWEB)

The paper deals with the disposal of radioactive waste and the plans for dealing with solid wastes of intermediate and low levels of activity, which are the responsibility of NIREX. NIREX is an executive body which co-ordinates the waste-disposal plans of the main radioactive waste producers. The disposal routes for the active wastes are described including the deep disposal of wastes containing material that will remain active for thousands of years. Requirements for deep burial are outlined with reference to the geology and hydrogeology of the site. Monitoring, maintenance and surveillance are mentioned for the protection of the public.

1984-02-01

187

UNSAT-H Version 3.0: Unsaturated Soil Water and Heat Flow Model Theory, User Manual, and Examples  

Energy Technology Data Exchange (ETDEWEB)

The UNSAT-H model was developed at Pacific Northwest National Laboratory (PNNL) to assess the water dynamics of arid sites and, in particular, estimate recharge fluxes for scenarios pertinent to waste disposal facilities. During the last 4 years, the UNSAT-H model received support from the Immobilized Waste Program (IWP) of the Hanford Site's River Protection Project. This program is designing and assessing the performance of on-site disposal facilities to receive radioactive wastes that are currently stored in single- and double-shell tanks at the Hanford Site (LMHC 1999). The IWP is interested in estimates of recharge rates for current conditions and long-term scenarios involving the vadose zone disposal of tank wastes. Simulation modeling with UNSAT-H is one of the methods being used to provide those estimates (e.g., Rockhold et al. 1995; Fayer et al. 1999). To achieve ...

2000-06-12

188

Study on immobilizing radioactive slurry based on alkali-activated slag-clay minerals composite cement  

International Nuclear Information System (INIS)

The feasibility of immobilizing simulated radioactive slurry (SRS) by alkali-activated slag---clay minerals composite cement (AASCM) was studied under the experimental conditions. The results show that the dosage of SRS and water cement ratio (W/C) have significant effect on the flowability of the mixture of AASCM and SRS. The more dosage of SRS, the lower flowability. When cement/sand ratio is 1: 1 and W/C is 0.45, the flowability of the mixture meets the case of solidification engineering and the compressive strength of the waste forms containing 20% SRS meets the needs of GB 14569.1-93. The setting time of the mixture of AASCM and SRS is highly dependent on temperature while sorts of anions have little influence on it. The application of AASCM is suitable below 20 degree C. The leaching resistance of AASCM based waste forms is superior to that of OPC based waste forms. The control of the forms to ...

2006-03-01

189

Pathway analysis for alternate low-level waste disposal methods  

International Nuclear Information System (INIS)

The purpose of this paper is to evaluate a complete set of environmental pathways for disposal options and conditions that the Nuclear Regulatory Commission (NRC) may analyze for a low-level radioactive waste (LLW) license application. The regulations pertaining In the past, shallow-land burial has been used for the disposal of low-level radioactive waste. However, with the advent of the State Compact system of LLW disposal, many alternative technologies may be used. The alternative LLW disposal facilities include below- ground vault, tumulus, above-ground vault, shaft, and mine disposal This paper will form the foundation of an update of the previously developed Sandia National Laboratories (SNL)/NRC LLW performance assessment methodology. Based on the pathway assessment for alternative disposal methods, a determination will be made about whether the current methodology can satisfactorily analyze the pathways and phenomena ...

1992-03-01

190

Enhanced biosorption of nickel(II) ions by silica-gel-immobilized waste biomass: Biosorption characteristics in batch and dynamic flow mode  

Energy Technology Data Exchange (ETDEWEB)

Batch and dynamic flow biosorption studies were carried out using the waste biomass entrapped in silica-gel matrix for the removal of nickel(II) ions from synthetic solutions and real wastewater. Batch biosorption conditions were examined with respect to initial pH, S/L ratio, contact time, and initial nickel ion concentration. Zeta potential measurements showed that immobilized biosorbent was negatively charged in the pH range of 3.0-8.0. The immobilized biomass was found to possess relatively high biosorption capacity (98.01 mg g{sup -1}), and biosorption equilibrium was established in a short time of operation (5 min). The equilibrium data were followed by Langmuir, Freundlich, and Dubinin-Radushkevich isotherm models. Scanning electron microscope analysis was used to screen the changes on the surface structure of the waste biomass after immobilization and nickel(II) biosorption. Sorbent-sorbate interactions were ...

2009-04-30

191

Ammonia recycling and destruction in a CFB gasifier  

Energy Technology Data Exchange (ETDEWEB)

Biomass contains nitrogen that is converted to NOx on combustion. Conversion of biomass into producer gas by thermal gasification offers an opportunity to reduce NOx-emissions by NH3 removal from the producer gas with water. Waste water will have to be treated before it can be drained. Recovered NH3 may have value as base chemical, but usually will have to be disposed off as waste. Recycling within the gasification process is an option to dispose off NH3 waste, provided NH3 is broken down under gasification conditions. We present experimental data on NH3 destruction in a CFB gasifier at temperatures from 780C to 860C, when NH3 is injected into the gasification air. Within that temperature range, the fraction of NH3 that is broken down increases from less than 50% to nearly 100%. Clearly, the presence of O2 at the injection point leads to a much higher rate of NH3 destruction than observed for purely ...

2004-05-01

192

Wind tunnel tests of biodegradable fugitive dust suppressants being considered to reduce soil erosion by wind at radioactive waste construction sites  

International Nuclear Information System (INIS)

Wind tunnel tests were performed of three fugitive dust control agents derived from potato and sugar beet products. These materials are being considered for use as dust suppressants to reduce the potential for transport of radioactive materials by wind from radioactive waste construction and remediation sites. Soil and dust control agent type, solution concentrations, application quantities, aging (or drying) conditions, surface disturbance, and wind and saltating sand eolian erosive stresses were selected and controlled to simulate application and exposure of excavated soil surfaces in the field. A description of the tests, results, conclusions, and recommendations are presented in this report. The results of this study indicate that all three dust control agents can protect exposed soil surfaces from extreme eolian stresses. It is also clear that the interaction and performance of each agent with various soil types may differ dramatically. ...

1993-01-01

193

Thermal Modeling and Performance Analysis of Interim Dry Storage and Geologic Disposal Facilities for Spent Nuclear Fuel  

Science.gov (United States)

Thermal models are constructed and analyses are performed of aluminum-based spent nuclear fuel (Al-SNF) in interim dry storage and geologic disposal configurations. Two models are developed, referred to as the interim storage model and the codisposal waste package (WP) model. Time-dependent source terms of Al-SNF forms and the defense high-level waste (DHLW) canisters are also developed for thermal performance analysis of the geologic codisposal WP.The interim storage model is a three-dimensional conduction-convection conjugate model to investigate the natural convection cooling of a sealed dry storage canister with vertical orientation in a dry storage vault. The analysis is made for various decay heat sources (equivalent to 25 to 35 kW/m{sup 3}) using various boundary conditions around the canister wall and with backfilled nitrogen or helium gas. Based on the data obtained from the Savannah River Site experimental work ...

2000-07-15

194

Regional assessment of nonforestry related biomass resources: Virginia  

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing on a county by county basis the agricultural crop, agricultural wastes, municipal wastes, and industrial wastes of Virginia that are potential biomass energy sources.

1988-11-01

195

Regional assessment of nonforestry related biomass resources: Florida  

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing in a county by county manner the agricultural crop, agricultural wastes, municipal wastes and industrial wastes in Florida that are potential biomass energy sources.

1988-11-01

196

Regional assessment of nonforestry related biomass resources: Alabama  

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing on a county by county basis the agricultural crop, agricultural wastes, municipal wastes and industrial wastes of Alabama that are potential biomass energy sources.

1988-11-01

197

Department of the  

Wastenet

Waste Technology and Innovation Study Final Report ...Waste Technology and Innovation Study Final Report 21/18569/150554 ...Survey of waste and resource recovery related technology and innovation, including products and product uses

198

Treatment of a waste salt delivered from an electrorefining process by an oxidative precipitation of the rare earth elements  

Energy Technology Data Exchange (ETDEWEB)

For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO{sub 2}, PrO{sub 2}), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two shapes: small cubic (oxide) and large plate-like (tetragonal) structures. The conversion efficiencies of the rare earth elements to their molten salt-insoluble ...

2009-02-28

199

Treatment of a waste salt delivered from an electrorefining process by an oxidative precipitation of the rare earth elements  

International Nuclear Information System (INIS)

For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO2, PrO2), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two shapes: small cubic (oxide) and large plate-like (tetragonal) structures. The conversion efficiencies of the rare earth elements to their molten salt-insoluble precipitates were ...

2009-02-28

200

Study on separation of CO2 gas by TSS (thermal swing sublimation) method. Part 2; TSS ho (Thermal Swing Sublimation: ondo swing shokaho) ni yoru tansan gas bunri no kenkyu. 2  

Energy Technology Data Exchange (ETDEWEB)

TSS (thermal swing sublimation) method was studied which uses vaporization heat and sensible heat of LNG for solidification and separation of CO2 gas in waste gases of LNG-fired combined cycle power generation system. In experiment, the mixed gas composed of CO2, H2O and N2 was used for simulating waste gas of LNG-fired combined cycle power generation systems, and the growth behavior of ice and dry ice was studied for developing dry ice making technology under low-temperature condition. As the experimental result, the following were clarified: various crystal structures depending on cooling temperature, the effect of gas flow rate on peeling of surface precipitated solids, and solidification characteristics of H2O/CO2 mixed gas. The growth rate of precipitated solid film thickness decreased with an increase in gas flow rate, while increased with CO2 concentration. The shape of a dry ice sublimator similar to that of a ...

1997-03-21

201

Study on a recovery of rare earth oxides from a LiCl-KCl-RECl3 system  

British Library Electronic Table of Contents (United Kingdom)

Radioactive rare earth chlorides in waste LiCl-KCl molten salts have to be separated as a stable form to minimize waste volume and to achieve stable solidification. In this work, thermal behavior of rare earth chlorides (CeCl3, GdCl3, NdCl3, PrCl3) was investigated in an oxygen condition to recover rare earth oxides from a LiCl-KCl-RECl3 system. The rare earth chlorides in the LiCl-KCl molten salts were smoothly converted to an oxychloride form at a higher temperature than 650degreeC, except for CeCl3. CeCl3 was totally converted to an oxide from at a higher temperature than 450degreeC. The rare earth oxychlorides (GdOCl, NdOCl, PrOCl) were effectively converted to oxide forms at a higher temperature than 1100degreeC. It was confirmed that rare earth oxides can be recovered from a LiCl-KCl...

2011-01-01

202

Removal and recovery system of hexavalent chromium from waste water by tannin gel particles  

Energy Technology Data Exchange (ETDEWEB)

Tannin gel particles that have extremely high adsorption capacity for hexavalent chromium Cr(VI) have been developed by controlling gelation of Mimosa tannin extracted from the bark of plants. The gelation process is composed of two stages; partial gelation of Mimosa tannin by reaction with formaldehyde (cross-linking agent) and granulation by dispersing the partially gelated solution into a liquid mixture of decalin ad a polyether nonionic surfactant with vigorous stirring. The structure of the tannin gel particles is controlled by a combination of operating conditions such as reaction time and temperature at both stages. The water content of the tannin gel particles that reflects their structure can be widely changed from 40 to 79 %(wet basis), even for a constant composition of 23 g Mimosa tannin and 6 ml formaldehyde (37 wt %). It is found that it is very important to increase the water content without losing mechanical strength and supply a large amount of ...

2000-10-01

203

Nuclear power and sustainable development  

International Nuclear Information System (INIS)

In Romania, the nuclear power is an element of sustainable development, being competitive, efficient and viable in the market economy. Fuel supply is ensured as nuclear fuel is manufactured in the country out of local uranium resources available in Romania. As for the environmental protection, it is known that, unlike the thermal power plants, the nuclear power plants do not release sulfur and nitrogen oxides, carbon dioxide and do not generate slag and ashes. The operation of nuclear power units does not release pollutants and, accordingly, these stations can contribute to the limitation and the abatement of environmental pollution. After seven years of Cernavoda NPP Unit 1 operation, a facility for storing low and medium level nuclear fuel wastes was built at the plant site as well as an intermediate dry storage for spent nuclear fuel whose first modules were commissioned in July 2003. They shall provide safe storage conditions for nuclear ...

2003-07-01

204

Methanogens and sulfate-reducing bacteria in oil sands fine tailings waste.  

Science.gov (United States)

In the past decade, the large tailings pond (Mildred Lake Settling Basin) on the Syncrude Canada Ltd. lease near Fort McMurray, Alta., has gone methanogenic. Currently, about 60%-80% of the flux of gas across the surface of the tailings pond is methane. As well as adding to greenhouse gas emissions, the production of methane in the fine tailings zone of this and other settling basins may affect the performance of these settling basins and impact reclamation options. Enumeration studies found methanogens (10(5)-10(6) MPN/g) within the fine tailings zone of various oil sands waste settling basins. SRB were also present (10(4)-10(5) MPN/g) with elevated numbers when sulfate was available. The methanogenic population was robust, and sample storage up to 9 months at 4 degrees C did not cause the MPN values to change. Nor was the ability of the consortium to produce methane delayed or less efficient after storage. Under laboratory conditions, fine ...

2000-10-01

205

Factors determining the stainless steel decontamination efficiency for the steam generator heat exchanger tubes at NPPs with the WWERs  

International Nuclear Information System (INIS)

To raise the efficiency of the redox method and decrease the amount of radioactive wastes, a possibility of improving the decontamination process for NPP heat exchanger tubes made of stainless steel is studied. In the home practice the redox method of equipment decontamination is carried out as a multi-cycle process. In each cycle the surface is treated first with a permanganate alkaline solution ther with an oxalic acid solution, with a condensate washing-at between the treatments. Using samples cut out of the steam generator pipelines of the first and third power units of the Novovoronezh NPP the effect of the oXalic acid concentration, as well as washout time and conditions on the decontamination factor are studied. On the basis of analysis of the obtained data a conclusion is drawn that using oxalic acid of low concentrations and increasing its concentrations from cycle to cycle maximum decontamination factor values can be obtained at a ...

206

Determination of pressure distribution in an aerated bed in a controlled pilot-scale compost reactor  

Energy Technology Data Exchange (ETDEWEB)

This study investigated the effectiveness of dealing with biological waste by composting. In particular, it examined the feasibility of recovering excess thermal energy produced in the process of composting biological waste in terms of mass and energy transport parameters required in the aerated compost bed. An experiment was performed in which a 100 dm{sup 3} adiabatic, leak-tight reactor equipped with a controlled aeration system was constructed to study the temperature and pressure distribution in the bed. Sensors were used to determine the amount and humidity of emitted gases under variable external physical conditions. The perforated bottom of the reactor allowed for bed aeration. As such, the humidity and heat were transported upwards, forced by the air pumped in and by natural convection. In terms of pressure distribution inside the composted and aerated bed, the study results showed that there were considerable ...

2010-07-01

207

Design/build/mockup of the Waste Isolation Pilot Plant gas generation experiment glovebox  

Energy Technology Data Exchange (ETDEWEB)

A glovebox was designed, fabricated, and mocked-up for the WIPP Gas Generation Experiments (GGE) being conducted at ANL-W. GGE will determine the gas generation rates from materials in contact handled transuranic waste at likely long term repository temperature and pressure conditions. Since the customer`s schedule did not permit time for performing R&D of the support systems, designing the glovebox, and fabricating the glovebox in a serial fashion, a parallel approach was undertaken. As R&D of the sampling system and other support systems was initiated, a specification was written concurrently for contracting a manufacturer to design and build the glovebox and support equipment. The contractor understood that the R&D being performed at ANL-W would add additional functional requirements to the glovebox design. Initially, the contractor had sufficient information to design the glovebox shell. Once the shell design was approved, ANL-W ...

1996-10-01

208

Decontamination of spills and residues of some pesticides and of protective clothing worn during the handling of the pesticides  

Energy Technology Data Exchange (ETDEWEB)

Users of pesticides may have waste or surplus quantities or spills for disposal. One alternative is to deactivate the pesticide at the handling site by using a straightforward chemical reaction. This option can be practical for those who use relatively small quantities of a large variety of pesticides, for example, greenhouse workers, small farmers, and agricultural researchers. This paper describes practical on-site methods for the disposal of spills or small waste quantities of five commonly used pesticides, Diazinon, Chlorpyrifos, Iprodione, 2,4-D, and Captan. These have been tested in the laboratory for the rate of disappearance of the pesticide, the degree of conversion to nontoxic products, the nature and identity of the products, the practicality of the method, and the ease of reproducibility. Methods selected were shown to be safe for the operator, reliable, and reproducible. Greater than 99% of the starting material had to be reacted ...

1996-12-31

209

Connecting section and associated systems concept for the spray calciner/in-can melter process  

Energy Technology Data Exchange (ETDEWEB)

For a number of years, researchers at the Pacific Northwest Laboratory have been developing processes and equipment for converting high-level liquid wastes to solid forms. One of these processes is the Spray Calciner/In-Can Melter system. To immobilize high-level liquid wastes, this system must be operated remotely, and the calcine must be reliably conveyed from the calciner to the melting furnace. A concept for such a remote conveyance system was developed at the Pacific Northwest Laboratory, and equipment was tested under full-scale, nonradioactive conditions. This concept and the design of demonstration equipment are described, and the results of equipment operation during experimental runs of 7 d are presented. The design includes a connecting section and its associated systems - a canister sypport and alignment concept and a weight-monitoring system for the melting furnace. Overall, the runs demonstrated that the ...

1981-06-01

210

Aqueous waste management for minor actinides and lanthanides separation process  

Energy Technology Data Exchange (ETDEWEB)

The French strategy of high level radioactive aqueous waste management is an incorporation in glassy fission products containers. Therefore, nitric acid soluble organic reagents needed for minor actinides and lanthanides selective separation from fission product solutions have to be sufficiently removed to reach carbon concentrations compatible with calcinator working. Thus, the ability of reagents to be oxidized under concentration conditions with or without denitration becomes a criteria of selection and have been studied. Further, if not working, other operations like hot hydrogen peroxide oxidation, catalyzed or not, are investigated. Reagents involved in this work are mainly complexing products (N-(2-Hydroxyethyl) Ethylene-diamine-tri-acetic Acid), pH keeping reagents (carboxylic acids like citric, glycolic, tartaric and lactic acid) and alkaline species (Tetramethylammonium hydroxide). Behaviour of acetic acid, which is often the main ...

2004-07-01

211

Permafrost at Lupin: Report of Phase II  

International Nuclear Information System (INIS)

The aim of the project is to study the conditions and processes occurring in permanently frozen crystalline bedrock, with special reference to deep (i.e., several hundreds of meters) bedrock conditions. The target of the study is the Lupin mine in Nunavut Territory, Northern Canada. The results may be utilized in assessing the long-term performance of deep underground constructions (e.g., nuclear waste repositories) in cooling climatic conditions. In Phase I of the project versatile background information was collected from the site e.g., on climate, geology and on hydrogeological and hydrogeochemical conditions. During Phase II a broad range of research was conducted including (i) electromagnetic soundings to investigate the distribution of permafrost in the surroundings of the mine; (ii) drilling of three research boreholes at the base of the permafrost for groundwater research; ...

2004-01-01

212

Quarterly progress report for the Chemical and Energy Research Section of the Chemical Technology Division: October-December 1997  

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the major activities conducted in the Chemical and Energy Research Section of the Chemical Technology Division at Oak Ridge National Laboratory (ORNL) during the period October--December 1997. The section conducts basic and applied research and development in chemical engineering, applied chemistry, and bioprocessing, with an emphasis on energy-driven technologies and advanced chemical separations for nuclear and waste applications. The report describes the various tasks performed within six major areas of research: Hot Cell Operations, Process Chemistry and Thermodynamics, Separations and Materials Synthesis, Fluid Structure and Properties, Biotechnology Research, and Molecular Studies. The name of a technical contact is included with each task described, and readers are encouraged to contact these individuals if they need additional information. Activities conducted within the area of Hot Cell Operations included efforts to optimize the ...

1999-02-01

213

Carbon Bed Mercury Emissions Control For Mixed Waste Treatment  

International Nuclear Information System (INIS)

Mercury has had various uses in nuclear fuel reprocessing and other nuclear processes, and so is often present in radioactive and mixed (both radioactive and hazardous according to the Resource Conservation and Recovery Act) wastes. Depending on regulatory requirements, the mercury in the off-gas must be controlled with sometimes very high efficiencies. Compliance to the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards can require off-gas mercury removal efficiencies up to 99.999% for thermally treating some mixed waste streams. Several test programs have demonstrated this level of off-gas mercury control using fixed beds of granular sulfur-impregnated activated carbon. Other results of these tests include: (a) The depth of the mercury control mass transfer zone was less than 15-30 cm for the operating conditions of these tests, (b) MERSORB(reg_sign) carbon can sorb ...

2010-11-01

214

High efficiency power production from biomass and waste  

Energy Technology Data Exchange (ETDEWEB)

Two-stage gasification allows power production from biomass and waste with high efficiency. The process involves pyrolysis at about 550C followed by heating of the pyrolysis gas to about 1300C in order to crack hydrocarbons and obtain syngas, a mixture of H2, CO, H2O and CO2. The second stage produces soot as unwanted by-product. Experimental results are reported on the suppression of soot formation in the second stage for two different fuels: beech wood pellets and Rofire pellets, made from rejects of paper recycling. Syngas obtained from these two fuels and from an industrial waste fuel has been cleaned and fed to a commercial SOFC stack for 250 hours in total. The SOFC stack showed comparable performance on real and synthetic syngas and no signs of accelerated degradation in performance over these tests. The experimental results have been used for the design and analysis of a future 25 MWth demonstration plant. As an alternative, a 2.6 MWth ...

2008-11-15

215

Waste management plan for the APT  

Energy Technology Data Exchange (ETDEWEB)

This revision of the APT Waste Management Plan details the waste management requirements and issues specific to the APT plant for design considerations, construction, and operation. The APT Waste Management Plan is by its nature a living document and will be reviewed at least annually and revised as required.

1997-08-22

218

Nuclear waste management: a perspective  

Energy Technology Data Exchange (ETDEWEB)

The scope of our problems with nuclear waste management is outlined. Present and future inventories of nuclear wastes are assessed for risk. A discussion of what is presently being done to solve waste management problems and what might be done in the future are presented. (DC)

1980-01-01

221

E-waste hazard: The impending challenge  

UK PubMed Central (United Kingdom)

Electronic waste or e-waste is one of the rapidly growing problems of the world. E-waste comprises of a multitude of components, some containing toxic substances that can have an adverse impact on human...Full Text Available

2008-08-01

225

40 CFR 261.2 - Definition of solid waste.  

Science.gov (United States)

...2009-07-01 false Definition of solid waste. 261.2 Section 261.2 Protection...PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) IDENTIFICATION AND LISTING OF HAZARDOUS WASTE General § 261.2 Definition...

2009-07-01

226

Hanford Waste Management Plan, 1987  

Energy Technology Data Exchange (ETDEWEB)

The purpose of the Hanford Waste Management Plan (HWMP) is to provide an integrated plan for the safe storage, interim management, and disposal of existing waste sites and current and future waste streams at the Hanford Site. The emphasis of this plan is, however, on the disposal of Hanford Site waste. The plans presented in the HWMP are consistent with the preferred alternative which is based on consideration of comments received from the public and agencies on the draft Hanford Defense Waste Environmental Impact Statement (HDW-EIS). Low-level waste was not included in the draft HDW-EIS whereas it is included in this plan. The preferred alternative includes disposal of double-shell tank waste, retrievably stored and newly generated TRU waste, one pre-1970 TRU solid waste site near the Columbia River ...

1987-01-01

227

Ecological utilization of wastes. A manual for optimum waste management concepts. 3. rev. ed. Oekologische Muellverwertung. Handbuch fuer optimale Abfall-Konzepte  

Energy Technology Data Exchange (ETDEWEB)

From out of the numerous technical alternatives the manual develops a waste management concept with emphasis on methods which can be coordinated for maximum ecological use and minimum economic costs. A clear-cut analysis of the present state of waste utilization and waste disposal in the Federal Republic of Germany (chapter 1) is followed by a detailed description of conventional and modern state-of-the-art waste utilization methods based on ecological evaluation criteria (chapter 3). An optimum waste utilization concept for defined quantities of wastes is derived from the ecological and economic comparison of waste utilization techniques given in chapter 3. Chapter 4 points out different variants of waste utilization and waste disposal methods and shows how to determine the optimum variant of the ...

1991-01-01

228

Waste Management Project fiscal year 1998 multi-year work plan, WBS 1.2  

Energy Technology Data Exchange (ETDEWEB)

The Waste Management Project manages and integrates (non-TWRS) waste management activities at the site. Activities include management of Hanford wastes as well as waste transferred to Hanford from other DOE, Department of Defense, or other facilities. This work includes handling, treatment, storage, and disposal of radioactive, nonradioactive, hazardous, and mixed solid and liquid wastes. Major Waste Management Projects are the Solid Waste Project, Liquid Effluents Project, and Analytical Services. Existing facilities (e.g., grout vaults and canyons) shall be evaluated for reuse for these purposes to the maximum extent possible.

1997-09-23

229

Thermal waste disposal and utilization; Waste management in accordance with the German Municipal Waste Disposal Regulations. Abfaelle thermisch entsorgen und verwerten; Die Verwaltungsvorschrift TA Siedlungsabfall praegt gesamte Abfallbehandlung  

Energy Technology Data Exchange (ETDEWEB)

Drastic changes in waste management procedures are expected from the German Municipal Waste Disposal Regulations which became effective on June 1, 1993. Waste disposal will be subject to certain restrictions which, e.g. demand that wastes must be pretreated and inerted before they are stored. These regulations favor thermal waste disposal methods such as the carbonization/combustion method which is planned for a commercial-scale plant in the city of Fuerth. (orig./BBR)

1993-09-01

230

Surface Crystallization and Composition of Spinel and Acmite in High-Level Waste Glass  

Science.gov (United States)

Surface crystallization and surface-to-bulk ratio in high-level waste glasses.

2000-07-10

231

Safe management of wastes from the mining and milling of Uranium and Thorium ores  

CERN Document Server

Safe management of wastes from the mining and milling of Uranium and Thorium ores

1987-01-01

232

Hazardous Waste Management on the Farm  

Science.gov (United States)

Sep 2, 2008 ... Abstract: This tutorial is intended to serve as a guide towards proper hazardous waste management. Knowing the regulations, different ...

233

Control of Effluent Gases from Solid Waste Processing Using Carbon Nanotubes  

Science.gov (United States)

One of the major problems associated with solid waste processing technologies is the release of

2005-01-01

235

The magnetoresonance operation of microwiggler on the piezoelectrics with a strong magnetic guide field  

Energy Technology Data Exchange (ETDEWEB)

We proposed that a new type of the electrostatic microwiggler with a wiggler period (0.1 mm {le}1{sub w}{le}1 mm) and the wiggler field strength (E{sub w}{le} 100 kV/m) can be produced on the surface of a PZT when a high power and high frequency ultrasonic wave travels through a PZT bar. Numerical simulations in the linear and nonlinear gain regime show that a weak microwiggler (E{sub w}100 kV/m,{lambda}{sub w}{approx}100 periods), operating in magnetoresonance with a strong guide field (B{sub o}{approx} 3.6T), can generate a millimeter and submillimeter radiations with medium electronic efficiency of few percents. It is shown that the maximum output power of the compact FEL using the wiggler system generated on the surface of the piezoelectric material may be upto a few Watts with a relatively low energy and low current electron beam (Ew {approx}100 keV and I{sub b}1 mA).

1995-12-31

236

Treatment of LiCl-KCl eutectic waste salt delivered from pyroprocessing of spent oxide fuel  

Energy Technology Data Exchange (ETDEWEB)

An oxidative precipitation reaction of rare-earth chlorides in a LiCl-KCl molten salt was successfully carried out by a lab-scale apparatus. The conversion efficiency of the used rare earth chlorides into the insoluble precipitates was increased with the sparging time and temperature and was affected on oxygen sparger type. In the conditions of 700 .deg. C molten salt temperature and above 540min sparging time, the final conversion efficiencies were over 99% for all the experimented rare-earth chlorides. The hydrodynamic characteristics of an oxygen-molten salt two phase flow system are very important for a co-oxidative precipitation of rare earth elements.

2008-08-15

237

Treatment of LiCl-KCl eutectic waste salt delivered from pyroprocessing of spent oxide fuel  

International Nuclear Information System (INIS)

An oxidative precipitation reaction of rare-earth chlorides in a LiCl-KCl molten salt was successfully carried out by a lab-scale apparatus. The conversion efficiency of the used rare earth chlorides into the insoluble precipitates was increased with the sparging time and temperature and was affected on oxygen sparger type. In the conditions of 700 .deg. C molten salt temperature and above 540min sparging time, the final conversion efficiencies were over 99% for all the experimented rare-earth chlorides. The hydrodynamic characteristics of an oxygen-molten salt two phase flow system are very important for a co-oxidative precipitation of rare earth elements

2008-08-01

238

Study on a transportation and emplacement system of pre-assembled EBS module for HLW geological disposal  

International Nuclear Information System (INIS)

HLW disposal is one of the largest issue to utilize Nuclear power safely. In the past study, the concept, which buffer materials and Overpacked waste were transported into underground respectively, have shown. The concept of pre-assembled engineered barrier has advantage to simplify the logistics and emplacement procedure, however there are difficulties to support heavy weight of pre-assembled package by equipment under the condition of little clearance between tunnel and package. In this study, Combination of air bearing and two degree-of-freedom wheels were suggested for transportation, and air jack was suggested for unloading and emplacement system. Also, whole system for transportation and emplacement procedure was designed, and Scale model test was examined to evaluate the feasibility of these concept and functions. (author)

2009-11-01

239

Road maps on research and development plans for water chemistry of nuclear power systems  

International Nuclear Information System (INIS)

Water chemistry of nuclear power plants has played an important role in reduction of personnel doses, structural materials and fuel integrity assurance, and reduction of radioactive wastes production. Further contributions are requested for advanced utilization of the LWR, advanced fuels and aging management of plants. Since water chemistry has an effect on all structure and materials immersed and at the same time affected by them, the optimum control not sticking to specific issues and covering the whole plant is required for these requests. Taking account of roles and activities of the industry, governmental institutes and academia, road maps on research and development plans for water chemistry were compiled into identified eleven items with targets and counter measures taken, such as common basic technologies, dose reduction, SCC mitigation, fuel cans corrosion/hydrogen absorption mitigation, condition based maintenance and flow accelerated ...

2008-05-01

240

Lebanon: assessment of the state of the environment.Final report  

International Nuclear Information System (INIS)

The study concerns the assessment of the state of the environment in Lebanon and the identification of policy options has three specific objectives namely to determine the conditions of the environment in Lebanon after years of wars (1975-1992); to identify environmentals trends associated with Lebanon's development and to assess their sustainability; to identify policy options for environmental management. Issues of the environment concerned are both the brown issues e.g. the management of wastes and effluent arising from human activitiesand green issues, the natural resource base defined through main receptors:air, water (including coastal waters), land and terrestrial ecology sectors such as agriculture, industry, energy, transport, tourism and fisheries, population and human settlements are also studied

241

Guidebook on design, construction and operation of pilot plants for uranium ore processing  

International Nuclear Information System (INIS)

The design, construction and operation of a pilot plant are often important stages in the development of a project for the production of uranium concentrates. Since building and operating a pilot plant is very costly and may not always be required, it is important that such a plant be built only after several prerequisites have been met. The main purpose of this guidebook is to discuss the objectives of a pilot plant and its proper role in the overall project. Given the wide range of conditions under which a pilot plant may be designed and operated, it is not possible to provide specific details. Instead, this book discusses the rationale for a pilot plant and provides guidelines with suggested solutions for a variety of problems that may be encountered. This guidebook is part of a series of Technical Reports on uranium ore processing being prepared by the IAEA's Division of Nuclear Fuel Cycle and Waste Management. 42 refs, 7 figs, 3 tabs.

242

Fingerprint testing of contaminated ventilation extract filter systems at Sizewell B  

International Nuclear Information System (INIS)

Sizewell B is Nuclear Electric's latest power station, and the Pressurised Water Reactor (PWR) design on which it is based represents a ''first'' for the UK. One of the integral components of the plant is the heating, ventilation and air-conditioning (HVAC) system, which performs a contamination control and gaseous waste management function for the site. During the commissioning of Sizewell B Power Station the extract systems of the HVAC plant underwent a procedure known as ''fingerprinting''. This entailed the characterisation of the facilities provided to test the filtration plant during its lifetime. The assessment of their adequacy was then used to identify necessary modifications and/or to propose the manner in which future in situ performance testing would be carried out. The paper outlines the basic principles and procedure that was used to ''fingerprint'' test systems during the commissioning of Sizewell B. A specific example is ...

243

Evaluation of the long-term mechanical behavior in the near-fields considering chemical transitions of barrier materials  

International Nuclear Information System (INIS)

An analysis system for the long-term mechanical behavior of barrier materials (MACBECE: Mechanical Analysis system considering Chemical transitions of BEntonite-based and CEment-based materials) was developed in order to improve the reliability of the evaluation of the hydraulic field which is one of the important environmental conditions in the safety assessment of the TRU waste disposal. MACBECE is the system that calculates the deformation of barrier materials using their chemical property changes as inputs, and subsequently calculates their hydraulic conductivity taking both their chemical property changes and deformation into consideration. By using MACBECE, the long-term deformation and the transition of hydraulic field for the round-type disposal cavities were evaluated, assuming some sets of chemical evolution data as input. Based on the analysis result, it is considered that the influence of the long-term deformation of the barrier ...

2007-04-22

244

Environmental information document: Savannah River Laboratory Seepage Basins  

Energy Technology Data Exchange (ETDEWEB)

This document provides environmental information on postulated closure options for the Savannah River Laboratory Seepage Basins at the Savannah River Plant and was developed as background technical documentation for the Department of Energy`s proposed Environmental Impact Statement (EIS) on waste management activities for groundwater protection at the plant. The results of groundwater and atmospheric pathway analyses, accident analysis, and other environmental assessments discussed in this document are based upon a conservative analysis of all foreseeable scenarios as defined by the National Environmental Policy Act (CFR, 1986). The scenarios do not necessarily represent actual environmental conditions. This document is not meant to be used as a closure plan or other regulatory document to comply with required federal or state environmental regulations.

1987-03-01

245

Environmental control for machine shops  

Energy Technology Data Exchange (ETDEWEB)

Metal machining facilities pose interesting design problems. This article provides an overview of key environmental control considerations and ways to deal with them. Machine shops offer a variety of environmental control challenges to mechanical engineers. Among the design problems that must be considered include: whether to provide space heating only or year-round air conditioning; temperature and relative humidity requirements; air cleanliness; exhaust air requirements; the type of HVAC system to be used; industrial waste and plumbing considerations; compressed air needs; and noise control. In addition, the designer must comply with worker health and safety and environmental protection regulations set forth by the National Institute of Safety and Health (NIOSH), OSHA, and EPA, as well as with any applicable state and local requirements.

1994-04-01

246

Biomass tar recycling and destruction in a CFB gasifier  

Energy Technology Data Exchange (ETDEWEB)

Conversion of biomass into producer gas by thermal gasification broadens the scope of biomass applications. Usually, tar has to be removed from the producer gas. Tar recycling within the gasification process may solve the associated waste problem and increase the system efficiency, provided tar is broken down under gasification conditions. We present results of tar recycling experiments at a Circulating Fluidised Bed gasifier. At 830{sup o}C, from each of 15 main tar compounds 70-80% are broken down. Continuous recycling of tar would increase the tar content in raw producer gas by 50% at most and save about 3% fuel input. 10 refs., 3 figs., 3 tabs.

2005-03-01

247

Request for interim approval to operate Trench 94 of the 218-E-12B Burial Ground as a chemical waste landfill for disposal of polychlorinated biphenyl waste in submarine reactor compartments. Revision 2.  

Science.gov (United States)

This request is submitted to seek interim approval to operate a Toxic Substances Control Act (TSCA) of 1976 chemical waste landfill for the disposal of polychlorinated biphenyl (PCB) waste. Operation of a chemical waste landfill for disposal of PCB waste ...

1994-01-01

248

Radioactive and mixed waste management plan for the Lawrence Berkeley Laboratory Hazardous Waste Handling Facility  

Energy Technology Data Exchange (ETDEWEB)

This Radioactive and Mixed Waste Management Plan for the Hazardous Waste Handling Facility at Lawrence Berkeley Laboratory is written to meet the requirements for an annual report of radioactive and mixed waste management activities outlined in DOE Order 5820.2A. Radioactive and mixed waste management activities during FY 1994 listed here include principal regulatory and environmental issues and the degree to which planned activities were accomplished.

1995-01-01

249

Charging generators for waste management costs  

Energy Technology Data Exchange (ETDEWEB)

Implementation of a plan to charge waste management costs to the facility that generates such waste requires a long-term commitment and consistent administration. The benefit is that generators are provided the incentive to optimize waste management practices if the charges are appropriately applied. This paper summarizes (1) a plan to charge waste generators, (2) the administrative structure of the plan, (3) a comparison between the rate structure and changes in waste disposal operations, and (4) issues that have surfaced as the plan is implemented. 2 refs., 1 fig., 1 tab.

1988-01-01

250

AVLIS production plant waste management plan  

Energy Technology Data Exchange (ETDEWEB)

Following the executive summary, this document contains the following: (1) waste management facilities design objectives; (2) AVLIS production plant wastes; (3) waste management design criteria; (4) waste management plan description; and (5) waste management plan implementation. 17 figures, 18 tables.

1984-11-15

251

Assessment of predictive models for the failure of titanium and ferrous alloys due to hydrogen effects. Report for the period of June 16 to September 15, 1981  

Energy Technology Data Exchange (ETDEWEB)

The 1977 version of the Simpson-Puls-Dutton model appears to be the most amenable with respect to utilizing known or readily estimated quantities. The Pardee-Paton model requires extensive calculations involving estimated quantities. Recent observations by Koike and Suzuki on vanadium support the general assumption that crack growth in hydride forming metals is determined by the rate of hydride formation, and their hydrogen atmosphere-displacive transformation model is of potential interest in explaining hydrogen embrittlement in ferrous alloys as well as hydride formers. The discontinuous nature of cracking due to hydrogen embrittlement appears to depend very strongly on localized stress intensities, thereby pointing to the role of microstructure in influencing crack initiation, fracture mode and crack path. The initiation of hydrogen induced failures over relatively short periods of time can be characterized with fair reliability using measurements of the threshold stress intensity. ...

1982-04-01

252

Hospital waste management in Lebanon  

International Nuclear Information System (INIS)

Hospital wastes comprises approximately 80% domestic waste components, also known as non-risk waste and 20% hazardous or risk waste. The 20% of the hospital waste stream or the risk waste (also known as infectious, medical, clinical wastes) comprises components which could be potentially contaminated with infections, chemical or radioactive agents. Therefore, it should be handled and disposed of in such a manner as to minimize potential human exposure and cross-contamination. Hospital risk waste and be subdivided into seven general categories as follows: infections, anatomical/pathological, chemical, pharmaceutical, radioactive waste, sharps and pressurised containers. These waste categories are generated by many types of health care establishments, including hospitals, clinics, ...

1999-06-02

253

Phenomenology of light systems using R-matrix theory.  

Energy Technology Data Exchange (ETDEWEB)

Over the last 30 years, a program of R-matrix analyses has been carried out at Los Alamos in the mass range 2 {le} A {le} 18 that gives useful information about the light systems. These analyses provide data for astrophysics, as well as for neutronic and thermonuclear applications, and can yield important constraints from the experimental measurements on the nature of few-body interactions. Following a brief introduction to R-matrix theory, I will describe recent work on reactions in the A=2 (NN) and A=4 systems. Finally, some comments will be made about extending the theory to complex energies in order to obtain information about resonances and other types of S-matrix singularities.

2001-01-01

254

AIDS and lung infection by Mycobacterium xenopi. Role of Computed Tomography; Sindrome da immunodeficienza acquisita e malattie polmonari da Mycobacterium xenopi. Ruolo della Tomografia Computerizzata  

Energy Technology Data Exchange (ETDEWEB)

Mycobacterium xenopi is one of the most common agents responsible for nontubercolar mycobacterial pulmonary disease on AIDS patients. These lesions have been studied with conventional radiography while CT has been used in patients with aspecific mycobacterioses or non-AIDS pulmonary conditions from Mycobacterium xenopi. 12 AIDS patients were examined. They had pulmonary lesions from Mycobacterium xenopi, patients age ranged 30 to 46 years. All patients had CD4 blood levels lower than 250 cells/mL and Mycobacterium xenopi in the sputum. All patients underwent a standard chest radiograph and a CT examination. CT images were evaluated by three radiologists independently and the definitive diagnosis was made in the presence of a fourth radiologist. Chest CT showed parenchymal consolidation in 66% of cases, associated with bilateral basal bands in 16% of cases. Consolidation was unilateral in 41% of cases and most frequently involved the right lower lobe. Bilateral ...

2000-06-01

255

Role of unsaturated soil in a waste containment system  

Energy Technology Data Exchange (ETDEWEB)

The role of the unsaturated properties of sand as a drainage layer in a composite liner system for landfills is investigated. The effect of the unsaturated properties of coarse-grained soil on contaminant migration was evaluated by means of a series of simulations using a one-dimensional model of a two- and a three-layer soil liner system for advection and diffusion, respectively. The results showed that under seepage conditions, the effect of an unsaturated sand layer on the advancement of the concentration front was quite insignificant. The arrival time of the C/C{sub o} = 0.5 concentration front increased from 651 days for the case with no sand layer to approximately 951 days for the case with a 1.0-m sand layer. A steady-state flow condition was ultimately established in the sand, and this fact suggests that the capillary action might not be effective. For diffusion, the arrival time of the concentration front increased nonlinearly with a ...

1996-12-31

256

Health-hazard evaluation report HETA 85-354-1872, Asarco, Denver, Colorado  

Science.gov (United States)

An evaluation was made of possible hazardous working conditions at the ASARCO Globe facility, Denver, Colorado. The facility was involved in the recovery of cadmium from baghouse dust, a waste byproduct of nonferrous smelters. A medical study of kidney function was conducted in 45 current or former cadmium production workers; results were compared to those for 35 hospital workers. Kidney abnormalities were more common and more severe in the cadmium workers than in the hospital workers. Abnormalities of proximal tubular function included reduced reabsorption of beta-2-microglobulin, retinol binding protein, calcium and phosphate. Glomerular dysfunction was evidenced as elevated serum creatinine. As length of exposure to cadmium increased, changes became more apparent in workers. No reversal of the conditions was noted in workers who had ceased to be exposed to cadmium some time before the study. The authors conclude that ...

1988-02-01

257

Effect of extraction conditions on the quality characteristics of pectin from passion fruit peel (Passiflora edulis f. flavicarpa L.)  

British Library Electronic Table of Contents (United Kingdom)

Passion fruit (Passiflora edulis f. flavicarpa L.) yellow variety is composed of 50-55g peel per 100g of fresh fruit which is discarded as waste during processing. Utilization of passion fruit peel for pectin extraction was studied. Passion fruit peel obtained after juice extraction was blanched in boiling water for 5min, dehydrated in a cross flow hot air drier at 60+-1degreeC to a moisture content of 4g/100g of dried peel. The dehydrated passion fruit peel was used for extraction experiments of pectin. The effect of pH, peel to extractant ratio, and number of extractions, extraction time and temperature on the yield and quality characteristics of pectin were investigated. The optimized conditions for extraction of pectin from passion fruit peel yielded 14.8g/100g of dried peel. Pectin ex...

2010-01-01

258

Development of pyro-separation technology based on molten salt electrolysis  

International Nuclear Information System (INIS)

In order to effectively recover uranium, rotation speed of solid cathode was examined, and effect of uranium concentration and current density on electrodeposition were confirmed. And the potentiostatic and galvanostatic electrorefining experiments were conducted. Element used in the experiments were Zr, Nd, La chlorides. The reduction potentials of chlorides metals on liquid Cd cathode were measured by cyclic voltammetry experiments. The electrowinning experiments were performed in order to recover small amounts of uranium in salt. Experimental set-up for the batch type reductive extraction experiments were developed and installed. On the base of experimental results of batch type, multi-stage extraction equipment was set-up, and optimum number of stage and recover yield were measured. In the oxidative extraction study is examine selective separation behavior of the rare earth metals from alloy composed of actinide and lanthanide metals to determine the effective separation ...

2010-10-01

259

Development of a process for the disposal of evaporation residues from NPP by precipitation/flocculation and solidification of the precipitation products. Final report  

International Nuclear Information System (INIS)

To reduce the volume of radioactive wastes after evaporation, activity carriers can be separated from the inactive salt load. Boric acid separation from PWR concentrates was considered a preliminary stage for nuclide precipitation. In connection with the precipitation process, the reaction conditions for boric acid separation were determined by bench-scale experiments. After evaluating the known purification processes, crystallization was suggested as a practicable method. After inactive bench-scale experiments, mixed crystal formation with iron hexacyanoferrate for Cs removal was chosen. The disturbing effect of the complexing agents was neutralized by a pre-dose of iron-III-salts. By specifying the precipitation conditions, for Cs-134 an activity separation from 3,0 E + 06 Bg/l to 1,9 E + 02 Bg/l, and for Cs-137 from 5,9 E + 06 Bg/l to 1,2 E + 02 Bg/l was achieved. Accordingly, the decontamination factor for Cs-134 was ...

260

A simple model for strontium breakthrough on zeolite columns  

Science.gov (United States)

The Process Waste Treatment Plant (PWTP) at the Oak Ridge National Laboratory is designed to remove radioactive contaminants, principally {sup 90}Sr, from process wastewater. Planned upgrades to the PWTP will use chabazite zeolite columns. Pilot-scale studies have shown that mass transfer zone lengths increase from 10 to about 30 cm as the superficial velocity increases from 5.5 to 22 cm/min. Calculations with a multicomponent equilibrium model showed that the distribution coefficient for strontium remains essentially constant over the process conditions, suggesting that a simple kinetic model (the Rosen long-bed solution) should adequately represent breakthrough behavior. Using a distribution coefficient of 4.87 L/g predicted by the equilibrium model, good agreement was found between experimental breakthrough curves and those calculated with the Rosen solution. This model allows prediction of bed depths and cycle times necessary to achieve the ...

1995-04-01

261

Hanford Waste Vitrification Plant Quality Assurance Program description for high-level waste form development and qualification  

International Nuclear Information System (INIS)

The Hanford Waste Vitrification Plant Project has been established to convert the high-level radioactive waste associated with nuclear defense production at the Hanford Site into a waste form suitable for disposal in a deep geologic repository. The Hanford Waste Vitrification Plant will mix processed radioactive waste with borosilicate material, then heat the mixture to its melting point (vitrification) to forin a glass-like substance that traps the radionuclides in the glass matrix upon cooling. The Hanford Waste Vitrification Plant Quality Assurance Program has been established to support the mission of the Hanford Waste Vitrification Plant. This Quality Assurance Program Description has been written to document the Hanford Waste Vitrification Plant Quality Assurance Program.

1993-05-06

262

Radwaste Drum Assay Technology by Segmented Gamma Scanning System  

Energy Technology Data Exchange (ETDEWEB)

Nuclear Act of Korea requires the manifest of low and intermediate level radioactive waste generated from nuclear power plants and other nuclear facilities prior to deliver to a disposal sites. Individual history records of the radioactive waste should be described the information about the activity of nuclides in the drum, total activity, weight, the type of waste. So a fully automated nuclide analysis assay system(non-destructive) of a radwaste drum was developed. For the nuclides that could not be analysed directly by MCA, the activities of the representative {gamma}-emitters(Cs-137, Co-60) contained in the drum were measured by using that system. Then the scaling factors were used to calculate the activities of {alpha} - and {beta}-emitters. This assay system divided a drum into 8 segments, a segment into 8 sectors to minimize analysis error, and used several methods(transmission ratio, differential peak absorption, ...

2009-01-15

263

Development of engineering parameters for the design of metal biosorption waste treatment systems  

Energy Technology Data Exchange (ETDEWEB)

Untreated landfill leachates and wastes from metal plating and mining operations are sources of environmental contamination by heavy metals. Because of their toxicity and potential for accumulation, the discharge of heavy metals must be controlled. Standard physical and chemical treatments used to remove metals from wastes such as concentration by electro-precipitation, ion exchange, solvent extraction, evaporative recovery, and conventional precipitation, are usually expensive and produce high quantities of sludge. Biosorption is the removal of metals from aqueous solutions by microorganisms. It is called biosorption rather than bioadsorption or bioaccumulation because the mechanisms of removal are not restricted to adsorption or metabolic uptake and so the more general term is preferable and has come to be accepted. In this thesis the focus is one two microorganisms and two metals. However, the possible combinations of ...

1991-12-03

264

Biosorption of heavy metals under anaerobic conditions. Final report; Biosorption von Schwermetallen unter anaeroben Bedingungen. Abschlussbericht  

Energy Technology Data Exchange (ETDEWEB)

The precipitation of heavy metals as hydroxides is the standard technique for the decontamination of waste water streams polluted by these elements. On the other side, progress in research has been made concerning the biosorption onto dead biomass and bioprecipitation supported by physiologically active bacteria. As the aim of this study, a flexible strategy has been envisaged cleaning a waste water with definite heavy metal load underlying the process mentioned above. Suitable bacteria were enriched and the process was tested in a technical plant. As result, a very high efficiency of heavy metal elimination has been found. The field of application covered by the acquired process is identical with the whole range of the waste water streams polluted by heavy metals. In addition, a second stage may be necessary if there are any further contaminants to be removed. (orig.) [Deutsch] Bei der Reinigung von schwermetallhaltigen ...

1996-12-31

265

Activities performed within the program of Nuclear Safety Research on structural and cladding materials for innovative reactor systems able to transmute nuclear waste  

International Nuclear Information System (INIS)

Full text: The transmutation of nuclear waste to reduce the burden on a geological repository is a relevant topic within the Program of Nuclear Safety Research of the Research Centre Karlsruhe. Several studies have confirmed that a high efficiency of transmutation of actinides is reached in fast neutron spectrum reactor system. Therefore, an important effort is dedicated to the study of transmutation strategies with different fast reactors and their associated technologies. Moreover, in international contexts as Generation IV International Forum (GIF) and Sustainable Nuclear Energy Technology Platform (SNETP), fast reactors are considered in the frame of sustainable development of nuclear energy and reduction of waste. The systems that are currently under investigation, in the frame of the different fuel cycle scenarios, are liquid metal cooled and gas cooled fast reactors as well as Accelerator Driven Sub-critical Transmutation devices (ADS). ...

2009-10-05

266

Waste laws. Waste Classification Ordinance. Residual Material Classification Ordinance. The Waste Technical Code. Ordinance on the Monitoring of Wastes and Residual Material. Ordinance on the Ban on CFCs and Halogenated Hydrocarbons. Packaging Ordinance. Sewage Ordinance. Text edition with index and an introduction by Dr. Clemens Weidemann. As of May 15, 1992. Abfallgesetz. AbfallbestimmungsV. ReststoffbestimmungsV. TA Abfall. Abfall- und ReststoffueberwachungsV. FCKW-Halon-VerbotsV. VerpackungsV. KlaerschlammV. Textausgabe mit Sachverzeichnis und einer Einfuehrung von Rechtsanwalt Dr. Clemens Weidemann. Stand: 15. Mai 1992  

Energy Technology Data Exchange (ETDEWEB)

The turbulent history of legislature concerned with the waste-management industry and the amount of material on this subject as well as the significance of the material in its own right led to the decision to publish all legal regulations on waste in one volume. It includes above all the Waste Law, Regulations on Determination of Waste, Regulations on Determination of Residual Products, Technical Instructions for Waste, Regulations for Monitoring Waste and Residual Products, Regulations on Probition from the Use of Chlorofluorohydrocarbons and Halon, Regulations on Packaging and Regulations on Sewage Sludge. The introduction explains the development and the role of the Waste Law and its applicability, goals and principles: The concept of waste, avoidance of waste, avoidance of ...

1992-01-01

267

Framework for managing wastes from oil and gas exploration and production (E&P) sites.  

Energy Technology Data Exchange (ETDEWEB)

Oil and gas companies operate in many countries around the world. Their exploration and production (E&P) operations generate many kinds of waste that must be carefully and appropriately managed. Some of these wastes are inherently part of the E&P process; examples are drilling wastes and produced water. Other wastes are generic industrial wastes that are not unique to E&P activities, such as painting wastes and scrap metal. Still other wastes are associated with the presence of workers at the site; these include trash, food waste, and laundry wash water. In some host countries, mature environmental regulatory programs are in place that provide for various waste management options on the basis of the characteristics of the wastes and the environmental ...

2007-09-15

268

Development and pilot demonstration program of a waste minimization plan at Argonne National Laboratory  

Energy Technology Data Exchange (ETDEWEB)

In response to US Department of Energy directives, Argonne National Laboratory (ANL) has developed a waste minimization plan aimed at reducing the amount of wastes at this national research and development laboratory. Activities at ANL are primarily research- oriented and as such affect the amount and type of source reduction that can be achieved at this facility. The objective of ANL's waste minimization program is to cost-effectively reduce all types of wastes, including hazardous, mixed, radioactive, and nonhazardous wastes. The ANL Waste Minimization Plan uses a waste minimization audit as a systematic procedure to determine opportunities to reduce or eliminate waste. To facilitate these audits, a computerized bar-coding procedure is being implemented at ANL to track hazardous wastes ...

1991-01-01

269

Attenuation of heavy metal leaching from hazardous wastes by co-disposal of wastes  

Energy Technology Data Exchange (ETDEWEB)

The potential hazard of landfill wastes was previously evaluated by examining the extraction procedures for individual waste, although various wastes were co-disposed of in actual landfills. This paper investigates the reduction of extraction-procedure toxicity by co-disposing various combinations of two wastes. When two wastes are mixed homogeneously, the extraction of heavy metals from the waste mixture is critically affected by the extract pH. Thus, co-disposal wastes will have a resultant pH between the pH values of its constituent. The lower the resultant pH, the lower the concentrations of heavy metals in the extract. When these wastes are extracted sequentially, the latter extracted waste has a stronger influence on the final concentration of heavy metals in the extract. Small-scale lysimeter ...

1996-12-31

270

Incorporation of tritiated stearic acid in polymer  

Energy Technology Data Exchange (ETDEWEB)

The chemical fixation of tritium in stearic acid followed by embedding the tritiated stearic acid into an epoxy resin proved to be a good method for permanent waste disposal of tritium gas. Tc-126 and Tc-136 hardener were used for this purpose. The polymerization temperature of the polymer products was found to be highly decreased by adding stearic acid and slightly decreased by adding stearic acid or by raising the temperature of the leachant medium and slightly decreased by irradiation. On the other hand, small improvement in the compressive strength of the polymer products was achieved by adding silica powder. The polymer product showed high flame points above 573 K although it contains stearic acid. DTA and TG analysis indicate that the thermal stability of polymer products containing stearic acid and silica powder is better than samples containing only stearic acid. Stearic acid was found to possess good resistance to irradiation and the amount of hydrogen and ...

1997-10-01

271

Factors affecting public and political acceptance for the implementation of geological disposal  

International Nuclear Information System (INIS)

The main objective of this paper is to identify conditions which affect public concern (either increase or decrease) and political acceptance for developing and implementing programmes for geologic disposal of long-lived radioactive waste. It also looks how citizens and relevant actors can be associated in the decision making process in such a way that their input is enriching the outcome towards a more socially robust and sustainable solution. Finally, it aims at learning from the interaction how to optimise risk management addressing needs and expectations of the public and of other relevant stakeholders. In order to meet these objectives, factors of relevance for societal acceptance conditions are identified, described and analysed. Subsequently these factors are looked for in the real world of nuclear waste management through cases in several countries. The analysis is conducted for six stages of a ...

2007-09-02

272

Biosphere modeling with climate changes for safety assessment of high-level radioactive waste geological isolation  

International Nuclear Information System (INIS)

In the safety assessment of a high-level radioactive waste (HLW) disposal system, it is required to estimate radiological impacts on future human beings arising from potential radionuclide releases from a deep repository into the surface environment. In order to estimate the impacts, a biosphere model is developed by reasonably assuming radionuclide migration processes in the surface environment and relevant human lifestyles. Releases from the repository might not occur for many thousands of years after disposal. Over such timescales, it is anticipated that the considerable climatic change, for example, induced by the next glaciation period expected to occur in around ten thousand years from now, will have a significant influence on the near surface environment and associated human lifestyles. In case of taking these evolution effects into account in modeling, it is reasonable to develop several alternative models on biosphere evolution systems consistent with ...

2001-01-01

273

Savannah River Site Interim Waste Management Program Plan FY 1991--1992  

Energy Technology Data Exchange (ETDEWEB)

The primary purpose of the Waste Management Program Plan is to provide an annual report of how Waste Management's operations are conducted, what facilities are being used to manage wastes, what forces are acting to change current waste management systems, and what plans are in store for the coming fiscal year. In addition, this document projects activities for several years beyond the coming fiscal year in order to adequately plan for safe handling, storage, and disposal of radioactive wastes generated at the Savannah River Site and for developing technology for improved management of wastes. In this document, work descriptions and milestone schedules are current as of December 1991.

1992-05-01

274

ICDF Complex Operations Waste Management Plan  

Science.gov (United States)

This Waste Management Plan functions as a management and planning tool for managing waste streams generated as a result of operations at the Idaho CERCLA Disposal Facility (ICDF) Complex. The waste management activities described in this plan support the selected remedy presented in the Waste Area Group 3, Operable Unit 3-13 Final Record of Decision for the operation of the Idaho CERCLA Disposal Facility Complex. This plan identifies the types of waste that are anticipated during operations at the Idaho CERCLA Disposal Facility Complex. In addition, this plan presents management strategies and disposition for these anticipated waste streams.

2006-12-01

275

Defense remote-handled transuranic waste implementation plan: Transuranic Waste Program System Integration Office  

Energy Technology Data Exchange (ETDEWEB)

This document presents a detailed schedule for the implementation of the strategy for managing defense remote-handled (RH) transuranic (TRU) waste. The baseline management strategy was defined in the Defense Remote-Handled Transuranic Waste Cost/Schedule Optimization Study and is summarized in this document. Also included are revised RH TRU waste inventory projections, current site management plans, a list of key decision points and milestones, and a discussion of uncertainties associated with management of RH TRU waste. The plans are summarized in a detailed schedule diagram and in an RH TRU waste work off diagram. 9 refs., 5 figs., 4 tabs.

1988-01-01

276

FDS3 simulations of indoor hydrocarbon fires engulfing radioactive waste packages  

International Nuclear Information System (INIS)

The thermal environment of a hypothetical large indoor hydrocarbon pool fire is more complex compared to outdoor fires and can be more severe for engulfed objects. In order to analyze potential thermal environments for interim storage of spent fuel casks or low-level radioactive waste packages engulfed in pool fires numerical simulations with the CFD fire code FDS3 were carried out for different storage configurations. In addition, data of indoor pool fire experiments were used to validate the model for this type of application. A series of pool fire experiments under different ventilation conditions and varied pool surface (1 m"2 - 4 m"2) inside a compartment of 3.6 m x 3.6 m x 5.7 m was conducted at iBMB (Institut fuer Baustoffe, Massivbau und Brandschutz) of Braunschweig University of Technology, Germany. The instrumentation included thermocouples, heatflux and pressure gauges, bi-directional flow probes and gas concentration measurements. A ...

2004-09-20

277

Streams of solid municipal wastes. Evaluation of data on the basis of waste follow-up system; Kiinteaen yhdyskuntajaetteen virrat: aineistotarkastelua jaetealan seurantajaerjestelmaen avulla  

Energy Technology Data Exchange (ETDEWEB)

The follow-up system for wastes (JAeSTI), developed at the end of the 1990s, forms a basis for today's followup activities in Finland. JAeSTI relies on an environmental protection database, the compliance monitoring system VAHTI operated by the environmental authorities. Waste followup and waste statistics depend very much on the annual waste quantities recorded in the VAHTI system. In the KYJ-project the coverage and reliability of the data in the VAHTI system was evaluated as for the streams of solid municipal waste. The project also included the compiling of national statistics on municipal waste for the year 2000. The project used other information sources, too, such as statistics compiled when the National Waste Plan and regional waste plans were revised in 2002. In addition, the extent and quantity of ...

2004-07-01

278

Transcription from the SV40 early-early and late-early overlapping promoters in the absence of DNA replication.  

UK PubMed Central (United Kingdom)

Transcription for a hybrid SV40 promoter-beta globin coding sequence recombinant initiates from both early-early (EE) and late-early (LE) SV40 start sites (EES and LES) in the absence of DNA replication....Full Text Available

1983-01-01

279

The renaissance of solar homes; Le renouveau des maisons solaires  

Energy Technology Data Exchange (ETDEWEB)

This publication of the Areva Group, a world nuclear industry leader, provides information on the energy in many domains. This issue deals with the nuclear fuel cycle, the biofuels, the everyday geothermal power, the Unites States energy supply and types, the Bertrand Picard solar aircraft, the kyoto protocol and the wind power leaders. A special chapter is devoted to the renaissance of solar homes. (A.L.B.)

2004-07-01

280

The molybdenum iron-sulphur protein from Desulfovibrio gigas as a form of aldehyde oxidase.  

UK PubMed Central (United Kingdom)

The molybdenum iron-sulphur protein originally isolated from Desulfovibrio gigas by Moura, Xavier, Bruschi, Le Gall, Hall & Cammack [(1976) Biochem. Biophys. Res. Commun. 72, 782-789] has been...Full Text Available

1987-05-01

281

Studies of neural networks for engine control: application to the electromechanical valves engine; Etudes des reseaux de neurones pour le controle moteur: application a soupapes electromecaniques  

Energy Technology Data Exchange (ETDEWEB)

This paper deals with the control of an electromechanical valves engine. The control uses neural networks in order to build a non-linear model of engine filing which depends on the driven inlets. The aim is to build this real-time model and to integrate this model to a control system which performs an iterative inversion. (J.S.)

1997-12-31

282

Solar rises in the south; Le solaire se leve au sud  

Energy Technology Data Exchange (ETDEWEB)

This autumn, Nice welcomed the thirteen European photovoltaic conference. It was the occasion for the world of solar energy to measure technical progress which were carried out and the market which are still to win. If developing countries are a reserve of new markets, they are not solvent and programmes depend on North/South negotiations. (N.C.).

1996-01-01

283

Scenario-Based Actions to Upgrade Small-Scale Furniture Producers and their Impacts on Women in Central Java, ...  

Science.gov (United States)

... Producers and their Impacts on Women in Central Java, IndonesiaActions basées sur des scénarios visant à élever ... impact sur les femmes dans le centre de Java, en IndonésieInvestigación-acción basada en...

284

Recommendations and quality control in brachytherapy; Recommandations pour le controle de qualite en curietherapie  

Energy Technology Data Exchange (ETDEWEB)

Brachytherapy consists of sealed radioactive source implantation. The diversity in the nature of radioelements, in their energy and activity requires strict implantation and utilization rules. These rules include radioactive source physical parameters check, after-loading machine and treatment planning system quality assurance and safe and reproducible dosimetric systems. Patient and medical workers information guarantee radioprotection and prevention of accidental exposures. (authors)

2002-11-01

285

Quality control in Nuclear Magnetic Resonance Imaging. Indications et strategies pour le controle de qualite en IRM  

Energy Technology Data Exchange (ETDEWEB)

In this article, the authors recall the factors apt to influence image quality in NMR Imaging and present the european works that have been developed in MRIQA to set 5 quality assurance tests: EUROSPIN 1 to 5.

1993-01-01

286

Plugging indicator for controlling the sodium quality. Indicateur de bouchage pour le controle de la qualite du sodium  

Energy Technology Data Exchange (ETDEWEB)

This device has and head-race pipe with an external part and a coaxial inner part. A measuring head is mounted movable between these 2 parts and has at least a thermocouple and a mobile grid for varying the section and the sodium flow to facilitate the impurities dissolution. This ensemble is completed by a longitudinal body containing the main parts of the indicator and surrounded by a thermal exchanger to cool the sodium.

1991-09-20

287

Neutronic detection device with extended flux range for control of nuclear reactors. Dispositif de detection neutronique a dynamique etendue pour le controle et la commande des reacteurs nucleaires  

Energy Technology Data Exchange (ETDEWEB)

The neutron detector is cased in a metal envelop and has one detector with a very sensitive fission chamber and a second detector with a fission chamber less sensitive that the first one and a boron coated ionisation chamber for reducing gamma radiation detection.

1992-06-12

288

Microwaves as low frequency radiation in degradations of pollutants; Le microonde come attivatori della degradazione di inquinanti  

Energy Technology Data Exchange (ETDEWEB)

The proposed aim of the work is to verify the effects produced on different kinds of environmental pollutants after exposure to a low frequency radiation such as microwaves. They have proved capable of producing minimum heating of the matrix as well as modifications in the structure of the molecules at the level of simple bonds. Steps were also taken ti check whether the degradation action of the microwaves could be boosted by sunlight. For this reason tests were run also on samples irradiated using microwaves and a lamp capable of simulating the sun's spectrum, as well as in the presence of a single lamp. [Italian] Lo scopo di questa ricerca e' di verificare gli effetti prodotti su inquinanti ambientali, di diversa natura, a seguito di un'esposizione ad una radiazione a bassa frequenza come le microonde. Le microonde possono produrre minimi riscladamenti della matrice e modificazioni della struttura delle molecole, a ...

1999-09-01

289

From tomography to voludensitometry: radiation detectors for industrial control and medical instrumentation; De la tomographie a la voludensitometrie: les capteurs pour le controle industriel et l`instrumentation medicale  

Energy Technology Data Exchange (ETDEWEB)

In this article, the author presents the main technological solutions, available or in development, on X-ray detectors in order to obtain a digital image in biomedical radiography or in industrial radiography: linear x-ray detectors and bidimensional x-ray detectors (memory radioluminescent screens, matrix plan detectors).

1993-12-01

290

Electric-field dependence of electroreflectance and photocurrent spectra at visible wavelengths in MOVPE-grown InAlGaP multiple strained quantum-well structures  

Science.gov (United States)

The authors present electric-field dependent electroreflectance and photocurrent spectra of visible-bandgap In{sub x}(Al{sub y}Ga{sub 1{minus}y}){sub 1{minus}x}P/In{sub x{prime}}(Al{sub y{prime}}Ga{sub 1{minus}y{prime}}){sub 1{minus}x{prime}}P multiple-quantum-well (MQW) structures. These structures, grown by metal-organic vapor phase epitaxy on 6{degrees}-misoriented (100) GaAs substrates, have undoped MQWs sandwiched between doped In{sub 0.5}Al{sub 0.5}P layers, forming p-i-n diodes. Quantum-well compositions in the range 0.46{le}x{le}0.52 and 0{le}y{le}0.4, corresponding to bandgaps in the red to yellow-green range, were used. The Stark shifts in these various samples were measured and found to depend on the details of the Mg p-type doping profile, confirming important diffusion effects, in agreement with secondary ion mass spectrometry and capacitance-voltage data. The results show that these new materials are promising for ...

1993-12-31

292

Application of an on-line measurement system for HF emission control (2. part); Application d'un systeme de mesure en ligne pour le controle des emissions de fluor (2. partie)  

Energy Technology Data Exchange (ETDEWEB)

In the last issue of 'L'Industrie ceramique et verriere', we presented the first part of this study. We describe in this issue the experimental procedure, the results and the conclusions of this work. (authors)

2005-02-01

293

A progress for the health of south countries. The solar refrigerator; Un progres pour la sante dans les pays du Sud. Le refrigerateur solaire  

Energy Technology Data Exchange (ETDEWEB)

In order to conserve vaccines in hot countries a solar refrigerator has been made by a French university. It is a photothermal refrigerator without batteries. It uses two gases: ammonia and calcium chloride. The refrigerator is autonomous and can work eleven days without sun. (N.C.)

1998-05-01

294

The Waste of the World  

Environmental Research Database

ObjectivesThis programme aims; To rethink how waste is thought about in social science; To provide a global analysis of waste; To examine how rethinking waste impinges on core social science concerns, notably: economies, researching globalisation, hazards and risk, and materiality. Social science understandings of waste position waste as the end-point of production and consumption, and see waste as a question of disposal.DescriptionThe Waste of the World is a five year research programme funded under ESRC's Large Grant Scheme. It brings together researchers in geography, anthropology and materials science from the University of Sheffield, Durham University, University College London and Goldsmiths College London, and connects the UK with South Asia (particularly India and Bangladesh), as well as the US, Europe and Kazakhstan. The ...

2011-01-30

295

Operable Unit 3-13, Group 3, Other Surface Soils Remediation Sets 4-6 (Phase II) Waste Management Plan  

Energy Technology Data Exchange (ETDEWEB)

This Waste Management Plan describes waste management and waste minimization activities for Group 3, Other Surface Soils Remediation Sets 4-6 (Phase II) at the Idaho Nuclear Technology and Engineering Center located within the Idaho National Laboratory. The waste management activities described in this plan support the selected response action presented in the Final Record of Decision for Idaho Nuclear Technology and Engineering Center, Operable Unit 3-13. This plan identifies the waste streams that will be generated during implementation of the remedial action and presents plans for waste minimization, waste management strategies, and waste disposition.

2006-07-01

296

Treatment of radioactive metallic waste by the electro-slag melting method  

Energy Technology Data Exchange (ETDEWEB)

The applicability of the electro-slag melting method for treating plutonium contaminated metallic waste was studied. A 100kg test furnace was built and simulated metallic waste was melted and solidified in this furnace. Waste volume was reduced to 1/25 with a decontamination factor of 25 and the slag and the copper mold are repeatedly usable. The process is expected to be employed in the project of PWTF (Plutonium contaminated Waste Treatment Facilities).

1983-01-01

297

Request for interim approval to operate 218-E-12B Trench 94 as a chemical waste landfill for disposal of polychlorinated biphenyl wastes in submarine reactor compartments.  

Science.gov (United States)

This request is submitted to seek interim approval to operate a chemical waste landfill for the disposal of polychlorinated biphenyl (PCB) wastes. This request covers only the disposal of small quantities of solid PCB wastes contained in decommissioned su...

1990-01-01

298

Projected radionuclide inventories of DWPF glass from current waste at time of production  

Energy Technology Data Exchange (ETDEWEB)

The Waste Acceptance Preliminary Specifications (WAPS) require that the DWPF estimate the inventory of long-lived radionuclides present in the waste glass, and report the values in the Waste Form Qualification Report. In this report, conservative (biased high) estimates of the radionuclide inventory of glass produced from waste currently in the Tank Farm are provided. In most cases, these calculated values compare favorably with actual data. In those cases where the agreement is not good, the values reported here are conservative.

1993-02-04

299

Industrial waste and pollution in Mongolia  

Energy Technology Data Exchange (ETDEWEB)

This paper very briefly outlines hazardous waste management issues, including regulations, in Mongolia. Air, water, and soil pollutants are identified and placed in context with climatic, social, and economic circumstances. The primary need identified is technology for the collection and disposal of solid wastes. Municipal waste problems include rapid urbanization and lack of sanitary landfills. Industrial wastes of concern are identified from the mining and leather industries. 4 refs., 2 tabs.

1996-12-31

300

Finally authorized supplementary report to the review on waste disposal in the Copenhagen area 1988. [Denmark]. Endelig godkendt bilagsrapport til affaldsredegoerelse for hovedstadsregionen 1988; Bilagsrapport nr. 1  

Energy Technology Data Exchange (ETDEWEB)

A supplementary report to the plan for waste disposal in the Copenhagen area, Denmark. It presents a mapping of wastes and waste flow in invidual areas, a description of recycling methods and waste collection systems. In addition legislative demands and potentials are dealth with. (CLS).

1988-07-01

301

Waste Generation and Pollution Prevention Progress Fact Sheet: Oak Ridge National Laboratory  

Energy Technology Data Exchange (ETDEWEB)

This 2-page fact sheet gives statistics on routine waste generation and projected reduction by waste type, and 1994 pollution prevention and recycling accomplishments at ORNL.

1996-09-01

302

Regional assessment of nonforestry related biomass resources: South Carolina  

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing in a county by county manner the agricultural crop, agricultural wastes, municipal wastes, and industrial wastes of South Carolina that are potential biomass energy sources.

1988-11-01

303

Regional assessment of nonforestry related biomass resources: North Carolina  

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing in a county by county manner the agricultural crop, agricultural wastes, municipal wastes and industrial wastes of North Carolina that are potential biomass energy sources.

1988-11-01

304

Probabilities of a catastrophic waste hoist accident at the Waste Isolation Pilot Plant  

Energy Technology Data Exchange (ETDEWEB)

This report shows the probability of a catastrophic accident involving the WIPP waste hoist system. Calculations and mitigation to reduce the probability of an accident and to minimize the impact of such an accident should be included. 10 refs., 8 figs., 4 tabs.

1990-01-01

305

Oak Ridge National Laboratory Technology Logic Diagram. Volume 2, Technology Logic Diagram: Part C, Waste Management  

Energy Technology Data Exchange (ETDEWEB)

This report documents site remediation at ORNL, including ORNL site characterization technologies, waste management and robotics and automation of the laboratory for waste processing and analysis.

1993-09-01

306

ORNL nuclear waste programs annual progress report for period ending September 30, 1982  

Energy Technology Data Exchange (ETDEWEB)

Research progress is reported in 20 activities under the headings: spent fuels, defense waste management, commercial waste management, remedial action, and conventional reactors. Separate entries were prepared for each activity.

1983-05-01

307

Integrated Models for Solid Waste Management in Tourism Regions: Langkawi Island, Malaysia  

Science.gov (United States)

The population growth, changing consumption patterns, and rapid urbanization contribute significantly to the growing volumes of solid waste that are generated in urban settings. As the rate of urbanization increases, demand on the services of solid waste management increases. The rapid urban growth in Langkawi Island, Malaysia, combined with the increasing rates of solid waste production has provided evidence that the traditional solid waste management practices, particularly the methods of waste collection and disposal, are inefficient and quite nonsustainable. Accordingly, municipal managers and planners in Langkawi ...

2011-09-04

308

Fusion Reactor Radioactive Waste Management.  

Science.gov (United States)

Quantities and compositions of non-tritium radioactive waste are estimated for some current conceptual fusion reactor designs, and disposal of large amounts of radioactive waste appears necessary. Although the initial radioactivity of fusion reactor and f...

1976-01-01

309

Department of Energy low-level waste management strategy  

Energy Technology Data Exchange (ETDEWEB)

The DOE strategy recognizes that public perception of low-level waste management practices is not positive. Actions are included that are aimed at opening the system to the public. A better informed public will be able to better assess the performance of the low-level waste management system.

1980-01-01

310

Cumulative releases of radionuclides from uncontained waste packages  

Energy Technology Data Exchange (ETDEWEB)

This report describes mathematical predictions for the migration of radionuclides from an emplaced radioactive waste container. The model assumes a spherical-equivalent waste solid surrounded by backfill but neglects the effect of decay heat. 7 refs., 2 tabs. (TEM)

1986-07-01

311

WASTE SOLIDIFICATION BUILDING BENCH SCALE HIGH ACTIVITY WASTE SIMULANT VARIABILITY STUDY FY2008  

Energy Technology Data Exchange (ETDEWEB)

The primary objective of this task was to perform a variability study of the high activity waste (HAW) acidic feed to determine the impact of feed variability on the quality of the final grout and on the mixability of the salt solution into the dry powders. The HAW acidic feeds were processed through the neutralization/pH process, targeting a final pH of 12. These fluids were then blended with the dry materials to make the final waste forms. A secondary objective was to determine if elemental substitution for cost prohibitive or toxic elements in the simulant affects the mixing response, thus providing a more economical simulant for use in full scale tests. Though not an objective, the HAW simulant used in the full scale tests was also tested and compared to the results from this task. A statistically designed test matrix was developed based on the maximum molarity inputs used to make the acidic solutions. The maximum molarity inputs were: 7.39 ...

2009-03-20

312

Co-combustion of recycled waste materials with peat and coal in a 15 kw fluidized bed reactor  

Energy Technology Data Exchange (ETDEWEB)

Co-combustion tests for recycled fuels and peat were made at a 15 kW fluidized bed reactor at VTT Energy in Jyvaeskylae. Peat was used as reference fuel. 25 tests in total were performed during 1994 - 1996. A part of the peat energy was substituted by coal in five tests, in order to change the sulphur/chlorine ratio of the fuel mixture. Fuel mixtures (25% recycled fuel and 75% peat, at energy ratio) were pelletized in order to get homogeneous fuel mixtures. The tests in the year 1994 were air staging experiments (with and without tertiary air). All test were performed with air staging in the years 1995 and 1996. The aim of the research was to determine whether the co-combustion of waste materials will cause additional emission problems, as compared to combustible emissions from conventional air-staged fluidized bed combustion. Further, the aim was to study which large-volume components can be burned safely. One aim was to study the influence of fuel properties and ...

1998-12-31

313

Waste management considerations for fusion power reactors  

International Nuclear Information System (INIS)

To estimate the waste management needs of a fusion power reactor, a scheme for handling radioactive waste from a fusion plant has been devised. The handling scheme proceeds with radioactive waste, primarily from blanket replacement, being stored on-site; waste in cooled and shielded casks is then isolated off-site; finally, the materials are recycled. Using activities and component lifetimes supplied by designers, several conceptual fusion power reactors have been analyzed and their waste streams compared to fission reactors with regard to total activity, specific activity, and lifetimes of activity.

314

Waste management considerations for fusion power reactors  

Science.gov (United States)

To estimate the waste management needs of a fusion power reactor, a scheme for handling radioactive waste from a fusion plant has been devised. The handling scheme proceeds with radioactive waste, primarily from blanket replacement, being stored on-site; waste in cooled and shielded casks is then isolated off-site; finally, the materials are recycled. Using activities and component lifetimes supplied by designers, several conceptual fusion power reactors have been analyzed and their waste streams compared to fission reactors with regard to total activity, specific activity, and lifetimes of activity.

1978-02-01

315

Solidification of problem wastes: Annual progress report, October 1985-September 1986  

Energy Technology Data Exchange (ETDEWEB)

This report describes initial work on the development of solidification systems for sodium nitrate waste and compacted waste. Sodium nitrate waste has been solidified in three types of materials: polyethylene, polyester-styrene (PES), and latex cement. Evaluations of the properties of the waste form, such as the ANS 16.1 leaching test, water immersion test and compressive strength measurements were performed on the waste forms containing various amounts of sodium nitrate. 9 refs., 9 figs., 7 tabs.

1987-02-01

316

Hazardous waste operational plan for site 300  

Energy Technology Data Exchange (ETDEWEB)

This plan outlines the procedures and operations used at LLNL's Site 300 for the management of the hazardous waste generated. This waste consists primarily of depleted uranium (a by-product of U-235 enrichment), beryllium, small quantities of analytical chemicals, industrial type waste such as solvents, cleaning acids, photographic chemicals, etc., and explosives. This plan details the operations generating this waste, the proper handling of this material and the procedures used to treat or dispose of the hazardous waste. A considerable amount of information found in this plan was extracted from the Site 300 Safety and Operational Manual written by Site 300 Facility personnel and the Hazards Control Department.

1982-02-12

317

Hazardous waste and environmental trade: China`s issues  

Energy Technology Data Exchange (ETDEWEB)

By presenting some case studies, this paper analyzes China`s situation with regard to hazardous waste: its environmental trade, treatment, and management. The paper describes China`s experiences with the environmental trade of hazardous waste in both the internal and international market. Regulations for managing the import of waste are discussed, as are China`s major approaches to the trading of hazardous waste both at home and overseas. The major reasons for setting up the Asian-Pacific Regional Training Center for Technology Transfer and Environmental Sound Management of Wastes in China and the activities involved in this effort are also described. 1 tab.

1996-12-31

318

Development of the alcohol waste processing equipment  

International Nuclear Information System (INIS)

In the experimental fast Reactor JOYO, gripper of Fuel Handling Machine and Ex-Vessel Transfer Machine that the sodium adhered is being washed with alcohol. This radioactive alcohol waste that was used to the washing is stored to the tank. If it is able to separate the alcohol and sodium in the alcohol waste it becomes possible to dispose of the alcohol waste. Japan Nuclear Institute and Fuji Electric Systems CO., LTD. Developed the device that adds carbonic acid gas to the alcohol waste and cause the sodium in the alcohol waste separated as carbonate and remove this carbonate by using the thin film evaporator. (author)

2004-11-01

319

Waste reduction at the Savannah River Site  

Energy Technology Data Exchange (ETDEWEB)

The Savannah River Site (SRS) is a key installation for the production and research of nuclear materials for national defense and peace time applications and has been operating a full nuclear fuel cycle since the early 1950s. Wastes generated include high level radioactive, transuranic, low level radioactive, hazardous, mixed, sanitary, and aqueous wastes. Much progress has been made during the last several years to reduce these wastes including management systems, characterization, and technology programs. The reduction of wastes generated and the proper handling of the wastes have always been a part of the Site's operation. This paper summarizes the current status and future plans with respect to waste reduction to waste reduction and reviews some specific examples of successful activities.

1990-01-01

320

Waste reduction at the Savannah River Site  

Energy Technology Data Exchange (ETDEWEB)

The Savannah River Site (SRS) is a key installation for the production and research of nuclear materials for national defense and peace time applications and has been operating a full nuclear fuel cycle since the early 1950s. Wastes generated include high level radioactive, transuranic, low level radioactive, hazardous, mixed, sanitary, and aqueous wastes. Much progress has been made during the last several years to reduce these wastes including management systems, characterization, and technology programs. The reduction of wastes generated and the proper handling of the wastes have always been a part of the Site`s operation. This paper summarizes the current status and future plans with respect to waste reduction to waste reduction and reviews some specific examples of successful activities.

1990-12-31

321

Solid Waste & Financial Assistance Program  

Science.gov (United States)

This program deals with solid waste disposal with topics/services covering: Reusable Building Materials and Large Household Items Exchange, Beneficial Use Determination, Biosolids, Certification, Compost Facil...

322

SUCCESSES AND EMERGING ISSUES IN SIMULATING THE MIXING BEHAVIOR OF LIQUID-PARTICLE NUCLEAR WASTE SLURRIES AT THE SAVANNAH RIVER SITE - 211B  

Energy Technology Data Exchange (ETDEWEB)

Aqueous radioactive high-level waste slurries are combined during processing steps that ultimately produce a stable borosilicate glass waste form. Chemically treated waste slurries are combined with each other and with glass frit-water slurries to produce the melter feed. Understanding the evolution of the rheological properties of the slurries is an important aspect of removing and treating the stored waste. To a first approximation, combinations of colloidal waste slurry with {approx}0.1-mm mean diameter glass frit or glass beads act in an analogous matter to slurries of spherical beads in Newtonian liquids. The non-Newtonian rheological properties of the waste slurries without frit, however, add complexity to the hydrodynamic analysis. The use of shear rate dependent apparent viscosities with the modified Einstein equation was used to model the rheological ...

2009-09-02

323

Proceedings of the eighth annual DOE low-level waste management forum: Technical Session 6, Waste treatment  

Energy Technology Data Exchange (ETDEWEB)

Nine papers in this proceedings have been processed for inclusion in the Energy Data Base. (AT)

1987-02-01

324

Nuclear waste plans enter critical phase  

Energy Technology Data Exchange (ETDEWEB)

A brief article considers the possible result of the enquiry into Nirex`s plan to build an underground rock laboratory at Sellafield in relation to radioactive waste disposal in the UK. (UK).

1996-10-31

325

Nuclear power plant liquid waste solidification system. [Japan  

Energy Technology Data Exchange (ETDEWEB)

The fundamental points to be considered in a waste treatment system for a country like Japan, where the final disposal method has not been decided and the wastes have to be stored in the power plants, are volume reduction of the wastes, safe storage of the wastes in the plant, and flexibility regarding the final disposal. A system has been developed that consists of a thin film evaporator for the direct solidification of the liquid waste, a pelletizer for producing hard pellets from the powdered wastes, a pellet storage unit, and a solidification unit for the final disposal. A pilot plant with waste treatment capacity of 200 kg/h was built in 1976 and has proved the system feasibility. This paper reports on pilot plant tests of the thin film evaporator and other components, tests on pellet deterioration during long term storage, and ...

1981-01-01

326

Nuclear power plant liquid waste solidification system  

International Nuclear Information System (INIS)

The fundamental points to be considered in a waste treatment system for a country like Japan, where the final disposal method has not been decided and the wastes have to be stored in the power plants, are volume reduction of the wastes, safe storage of the wastes in the plant, and flexibility regarding the final disposal. A system has been developed that consists of a thin film evaporator for the direct solidification of the liquid waste, a pelletizer for producing hard pellets from the powdered wastes, a pellet storage unit, and a solidification unit for the final disposal. A pilot plant with waste treatment capacity of 200 kg/h was built in 1976 and has proved the system feasibility. This paper reports on pilot plant tests of the thin film evaporator and other components, tests on pellet deterioration during long term storage, and ...

1981-02-26

327

Nondestructive characterization of low-level transuranic waste  

Energy Technology Data Exchange (ETDEWEB)

The use of nondestructive evaluation (NDE) methods is proposed for characterization of transuranic (TRU) waste stored at the Radioactive Waste Management Complex. These NDE methods include real-time x-ray radiography, real-time neutron radiography, x-ray and neutron computed tomography, thermal imaging, container weighing, visual examination, and acoustic measurements. An integrated NDE system is proposed for characterization and certification of TRU waste destined for eventual shipment to the Waste Isolation Pilot Plant in New Mexico. Methods for automating both the classification waste and control of a complete nondestructive evaluation/nondestructive assay system are presented. Feasibility testing of the different NDE methods, including real-time x-ray radiography, and development of automated waste classification techniques are covered as part of a five year ...

1981-10-01

328

NASA - Waste Not  

Science.gov (United States)

Jun 4, 2004 ... On a two-year trip to Mars, according to one estimate, a crew of six humans will generate more than six tons of solid organic waste--much of ...

329

NAME=\\  

Wastenet

... Waste Collection Systems Products and Equipment Find and compare a variety of waste collection systems products and equipment on the world's largest environmental industry portal. View product ...

330

Mixed waste disposal facility at the Nevada Test Site  

Energy Technology Data Exchange (ETDEWEB)

This report provides a brief overview of the history and planning for a proposed mixed waste disposal site on the Nevada Test Site. 8 figs.

1987-01-01

331

Kraft pulping of industrial wood waste  

Science.gov (United States)

Jun 16, 2011 ... Description: Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for ...

332

Fish waste - NASA Quest  

Science.gov (United States)

Seriously, generally fish waste does drop, but quite slowly. But a good group of snails should still do a fine job of cleaning the tank. ...

333

Factoring Potential Accelerator Transmutation of Waste Demonstrations into Accelerator Production of Tritium Design Planning  

CERN Document Server

Factoring Potential Accelerator Transmutation of Waste Demonstrations into Accelerator Production of Tritium Design Planning

1998-01-01

334

Current waste-management practices and operations at Oak Ridge National Laboratory, 1982  

Energy Technology Data Exchange (ETDEWEB)

The need for efficient management of industrial chemical wastes, especially those considered hazardous or radioactive, is receiving increased attention in the United States. During the past five years, several federal laws have addressed the establishment of stronger programs for the control of hazardous and residual wastes. At a facility such as Oak Ridge National Laboratory (ORNL), an efficient waste management program is an absolute necessity to ensure protection of human health and compliance with regulatory requirements addressing the treatment and disposal of hazardous, nonhazardous, and radioactive wastes. This report highlights the major regulatory requirements under which the Laboratory must operate and their impact on ORNL facilities. Individual waste streams, estimates of quantities of waste, and current waste management ...

1982-09-01

335

Converting Simulated Sodium-bearing Waste into a Single Solid Waste Form by Evaporation: Laboratory- and Pilot-Scale Test Results on Recycling Evaporator Overheads  

Energy Technology Data Exchange (ETDEWEB)

Conversion of Idaho National Engineering and Environmental Laboratory radioactive sodium-bearing waste into a single solid waste form by evaporation was demonstrated in both flask-scale and pilot-scale agitated thin film evaporator tests. A sodium-bearing waste simulant was adjusted to represent an evaporator feed in which the acid from the distillate is concentrated, neutralized, and recycled back through the evaporator. The advantage to this flowsheet is that a single remote-handled transuranic waste form is produced in the evaporator bottoms without the generation of any low-level mixed secondary waste. However, use of a recycle flowsheet in sodium-bearing waste evaporation results in a 50% increase in remote-handled transuranic volume in comparison to a non-recycle flowsheet.

2004-01-01

336

Acid Waste Equipment on Environmental Expert  

Wastenet

...Systems by IPEX Enfield electrofusion acid waste systems give you the proven corrosion resistance of polypropylene, along with our patented, state-of-the-art electrofusion system....

337

Spent fuel transportation cask response to a tunnel fire scenario  

Energy Technology Data Exchange (ETDEWEB)

On July 18, 2001, a freight train carrying hazardous (non-nuclear) materials derailed and caught fire while passing through the Howard Street railroad tunnel in downtown Baltimore, Maryland. The United States Nuclear Regulatory Commission (USNRC), one of the agencies responsible for ensuring the safe transportation of radioactive materials in the United States, undertook an investigation of the train derailment and fire to determine the possible regulatory implications of this particular event for the transportation of spent nuclear fuel by railroad. Shortly after the accident occurred, the USNRC met with the National Transportation Safety Board (NTSB), the U.S. agency responsible for determining the cause of transportation accidents, to discuss the details of the accident and the ensuing fire. Following these discussions, the USNRC assembled a team of experts from the National Institute of Standards and Technology (NIST), the Center for Nuclear Waste Regulatory ...

2004-07-01

338

Investigation of corrosion experienced in a spray calciner/ceramic melter vitrification system  

Energy Technology Data Exchange (ETDEWEB)

After periodic testing of a large-scale spray calciner/ceramic melter vitrification system over a 2-yr period, sufficient corrosion was noted on various parts of the vitrification system to warrant its disassembly and inspection. A majority of the 316 SS sintered metal filters on the spray calciner were damaged by chemical corrosion and/or high temperature oxidation. Inconel-601 portions of the melter lid were attacked by chlorides and sulfates which volatilized from the molten glass. The refractory blocks, making up the walls of the melter, were attacked by the waste glass. This attack was occurring when operating temperatures were >1200/sup 0/C. The melter floor was protected by a sludge layer and showed no corrosion. Corrosion to the Inconel-690 electrodes was minimal, and no corrosion was noted in the offgas treatment system downstream of the sintered metal filters. It is believed that most of the melter corrosion occurred during one specific operating ...

1980-08-01

339

Hybrid Combined Cycles with Biomass and Waste Fired Bottoming Cycle - a Literature Study  

Energy Technology Data Exchange (ETDEWEB)

Biomass is one of the main natural resources in Sweden. The present low-CO{sub 2} emission characteristics of the Swedish electricity production system (hydro and nuclear) can be retained only by expansion of biofuel applications for energy purposes. Domestic Swedish biomass resources are vast and renewable, but not infinite. They must be utilized as efficiently as possible, in order to make sure that they meet the conditions for sustainability in the future. Application of efficient power generation cycles at low costs is essential for meeting this challenge. This applies also to municipal solid waste incineration with energy extraction, which should be preferred to its dumping in landfills. Hybrid dual-fuel combined cycle units are a simple and affordable way to increase the electric efficiency of biofuel energy utilization, without big investments, uncertainties or loss of reliability arising from complicated technologies. Configurations of ...

2002-02-01

340

Review of high-level waste form properties. [146 bibliographies  

Energy Technology Data Exchange (ETDEWEB)

This report is a review of waste form options for the immobilization of high-level-liquid wastes from the nuclear fuel cycle. This review covers the status of international research and development on waste forms as of May 1979. Although the emphasis in this report is on waste form properties, process parameters are discussed where they may affect final waste form properties. A summary table is provided listing properties of various nuclear waste form options. It is concluded that proposed waste forms have properties falling within a relatively narrow range. In regard to crystalline versus glass waste forms, the conclusion is that either glass of crystalline materials can be shown to have some advantage when a single property is considered; however, at this date no single waste form offers optimum ...

1980-12-01

341

Oak Ridge National Laboratory Waste Management Plan, fiscal year 1994. Revision 3  

Energy Technology Data Exchange (ETDEWEB)

US Department of Energy (DOE) Order 5820.2A was promulgated in final form on September 26, 1988. The order requires heads of field organizations to prepare and to submit updates on the waste management plans for all operations under their purview according to the format in Chap. 6, {open_quotes}Waste Management Plan Outline.{close_quotes} These plans are to be submitted by the DOE Oak Ridge Operations Office (DOE-ORO) in December of each year and distributed to the DP-12, ES&H-1, and other appropriate DOE Headquarters (DOE-HQ) organizations for review and comment. This document was prepared in response to this requirement for fiscal year (FY) 1994. The Oak Ridge National Laboratory (ORNL) waste management mission is reduction, collection, storage, treatment, and disposal of DOE wastes, generated primarily in pursuit of ORNL missions, in order to protect human health and safety and the environment. ...

1993-12-01

342

The Decommissioning of the Trino Nuclear Power Plant  

Energy Technology Data Exchange (ETDEWEB)

Following a referendum in Italy in 1987, the four Nuclear Power Plants (NPPs) owned and operated by the state utility ENEL were closed. After closing the NPPs, ENEL selected a ''safestore'' decommissioning strategy; anticipating a safestore period of some 40-50 years. This approach was consistent with the funds collected during plant operation, and was reinforced by the lack of both a waste repository and a set of national free release limits for contaminated materials in Italy. During 1999, twin decisions were made to privatize ENEL and to transform the nuclear division into a separate subsidiary of the ENEL group. This group was renamed Sogin and during the following year, ownership of the company was transferred to the Italian Treasury. On formation, Sogin was asked by the Italian government to review the national decommissioning strategy. The objective of the review was to move from a safestore strategy to a prompt ...

2002-02-27

343

Study on the measurement method of diffusion coefficient for radon in the soil. 6  

International Nuclear Information System (INIS)

The aim of this study is to clarify the radon behavior in the soil at the waste rock yards of uranium mine. We have developed an apparatus for measuring radon diffusion coefficient in soil under the control of soil temperature. The radon diffusion coefficients changed suddenly around the soil temperature of 0degC. The radon diffusion coefficients in dry soil have little temperature dependency, and were comparable coefficients obtained by empirical formula of Rogers and Nielson. To study the restraint effect of radon exhalation by covering with bentonite on soil, we carried out the measurements and the calculations by using one-dimensional transport model of atmosphere and soil. The decrease of radon exhalation rate was 2.9 Bq m"-"2s"-"1 when soil covered with the bentonite of 5 cm thick. The radon concentrations in snow cover and the radon flux from the snow surface were measured at the waste rock yard in Ningyo-toge Environmental Engineering ...

344

Study of the distribution of gamma emitters radionuclides between a pollution abatement factory and its surrounding environment; Case of the water treatment plant of the Grand Caen district. Study report; Etude de la repartition de radionucleides artificiels emetteurs gamma entre une usine de depollution et son milieu environnant; Cas de la station d'epuration du District du Grand Caen. Rapport d'etude  

Energy Technology Data Exchange (ETDEWEB)

Except nuclear industry, diverse structures (hospitals, of research or manufacturers) can have appeal to the use of radioisotopes conditioned under unsealed shape. Such practices lead to tolerate releases in environment in the respect of a statutory device. So the collective network can contain radioisotopes the future of which is going to depend partially on the cleaning applied to waste water. This study through the analysis of a concrete case, has for objective to inform about the future of gamma radioelements present in waste water treated by a wastewater treatment plant. The contamination of the network is essentially due to Tc{sup 99} and I{sup 131}, radioelements present whatever the working day and the hour considered. The total estimated in-load for a day is important, of the order of 4000 MBq for Tc{sup 99} and 15 to 300 MBq for I{sup 131}. The assessment of cleaning of the station shows that this one plays a role ...

2007-07-01

345

SR 97 - Alternative models project. Discrete fracture network modelling for performance assessment of Aberg  

Energy Technology Data Exchange (ETDEWEB)

As part of studies into the siting of a deep repository for nuclear waste, Swedish Nuclear Fuel and Waste Management Company (SKB) has commissioned the Alternative Models Project (AMP). The AMP is a comparison of three alternative modeling approaches for geosphere performance assessment for a single hypothetical site. The hypothetical site, arbitrarily named Aberg is based on parameters from the Aespoe Hard Rock Laboratory in southern Sweden. The Aberg model domain, boundary conditions and canister locations are defined as a common reference case to facilitate comparisons between approaches. This report presents the results of a discrete fracture pathways analysis of the Aberg site, within the context of the SR 97 performance assessment exercise. The Aberg discrete fracture network (DFN) site model is based on consensus Aberg parameters related to the Aespoe HRL site. Discrete fracture pathways are identified from canister ...

1999-08-01

346

Preliminary delineation of natural geochemical reactions, Snake River Plain aquifer system, Idaho National Engineering Laboratory and vicinity, Idaho  

Energy Technology Data Exchange (ETDEWEB)

The U.S. Geological Survey, in cooperation with the U.S. Department of Energy, is conducting a study to determine the natural geochemistry of the Snake River Plain aquifer system at the Idaho National Engineering Laboratory (INEL), Idaho. As part of this study, a group of geochemical reactions that partially control the natural chemistry of ground water at the INEL were identified. Mineralogy of the aquifer matrix was determined using X-ray diffraction and thin-section analysis and theoretical stabilities of the minerals were used to identify potential solid-phase reactants and products of the reactions. The reactants and products that have an important contribution to the natural geochemistry include labradorite, olivine, pyroxene, smectite, calcite, ferric oxyhydroxide, and several silica phases. To further identify the reactions, analyses of 22 representative water samples from sites tapping the Snake River Plain aquifer system were used to determine the thermodynamic ...

1997-05-01

347

Phase 2 report on the evaluation of polyacrylonitrile (PAN) as a binding polymer for absorbers used to treat liquid radioactive wastes  

Energy Technology Data Exchange (ETDEWEB)

The performance of PAN-based composite absorbers was evaluated in dynamic experiments at flow rates ranging from 25--100 bed volumes (BV) per hour. Composite absorbers with active components of ammonium molybdophosphate (AMP) PAN and K-Co ferrocyanide (KCoFC) PAN were used for separating Cs from a 1 M HNO{sub 3} + 1 M NaNO{sub 3} + 2 {times} 10{sup {minus}5} M CsCl acidic simulant solution. KCoFC-PAN and two other FC-based composite absorbers were tested for separating Cs from alkaline simulant solutions containing 0.01 M to 1 M NaOH and 1 M NaNO{sub 3} + x {times} 10{sup {minus}4} M CsCl. The efficiency of the Cs sorption on the AMP-PAN absorber from acidic simulant solutions was negatively influenced by the dissolution of the AMP active component. At flow rates of 50 BV/hr, the decontamination factor of about 10{sup 3} could be maintained for treatment of 380 BV of the feed. With the KCoFC-PAN absorber, the decontamination factor of about 10{sup 3} could be maintained for a feed ...

1996-05-01

348

Metallurgical Laboratory Hazardous Waste Management Facility groundwater monitoring report. Third quarter, 1994  

Energy Technology Data Exchange (ETDEWEB)

During third quarter 1994, samples from AMB groundwater monitoring wells at the Metallurgical Laboratory Hazardous Waste Management Facility (Met Lab HWMF) were analyzed for selected heavy metals, indicator parameters, radionuclides, volatile organic compounds, and other constituents. Eight parameters exceeded standards during the quarter. As in previous quarters, tetrachloroethylene and trichloroethylene exceeded final Primary Drinking Water Standards (PDWS). Bis(2-ethylhexyl) phthalate exceeded final PDWS in one well. Aluminum, iron, manganese, tin, and total organic halogens exceeded the Savannah River Site (SRS) Flag 2 criteria. Groundwater flow direction and rate in the M-Area Aquifer Zone were similar to previous quarters. Conditions affecting determination of groundwater flow directions and rates in the Upper Lost Lake Aquifer Zone, Lower Lost Lake Aquifer Zone, and the Middle Sand Aquifer Zone of the Crouch Branch Confining Unit were ...

1994-12-01

349

Irradiation damage in spinel ceramics MgAl_2O_4 and ZnAl_2O_4: application to the transmutation of the nuclear waste  

International Nuclear Information System (INIS)

The transmutation of minor actinides in-reactor is one solution currently being studied for the long time management of nuclear waste. In the heterogeneous concept the radionuclides are incorporating in an inert ceramic matrix. The support material must be insensitive to radiation damage. Fission product damage is the main radiation damage source during the transmutation process and therefore it is of the utmost importance to study their effects. We irradiated spinels MgAl_2O_4 (matrix of reference) and ZnAl_2O_4 by fast ions (by example: (86)Kr of approximately 400 MeV) simulating the fission products. Under these conditions, the damage is primarily due to the electronic energy losses (Se). One of the structural features of spinel AB_2O_4 is that the two cations (A(2+) and B(3+)) can exchange their site. This phenomenon is quantified by the inversion parameter. We highlight by XRD in grazing incidence that the structural changes observed in ...

350

Imaging of reflection seismic and radar wavefields: Monitoring of steam-heated oil reservoirs and characterization of nuclear waste repositories  

Energy Technology Data Exchange (ETDEWEB)

A new three-dimensional (3D) acoustic modelling method was developed using a first-order hyperbolic wave system which was solved with explicit finite dfferences. The numerical solution of the 3D wave system provides a useful method for simulating evolution of a pressure field corresponding to compressional type waves. Existing two-dimensional (2D) elastic modelling algorithms were modified and fine-tuned for computationally efficient and realistic wave propagation simulations in complex structures. An original formulation of the 3D reverse time migration method was developed which is very accurate, does not suffer from unwanted evenescent energy, can image dips beyond 90{degree}, and does not generate multiple energy. Two case studies were performed that involved steam stimulation projects in the Cold Lake deposit. Simulations were performed during different phases of the steam stimulation process to examine the relation between reservoir properties and conditions ...

1994-12-31

351

Ground penetrating radar and direct current resistivity evaluation of the desiccation test cap, Savannah River Site  

Energy Technology Data Exchange (ETDEWEB)

The Savannah River Site (SRS) has a variety of waste units that may be temporarily or permanently stabilized by closure using an impermeable cover to prevent groundwater infiltration. The placement of an engineered kaolin clay layer over a waste unit is an accepted and economical technique for providing an impermeable cover but the long term stability and integrity of the clay in non-arid conditions is unknown. A simulated kaolin cap has been constructed at the SRA adjacent to the Burial Ground Complex. The cap is designed to evaluate the effects of desiccation on clay integrity, therefore half of the cap is covered with native soil to prevent drying, while the remainder of the cap is exposed. Measurements of the continuing impermeability of a clay cap are difficult because intrusive techniques may locally compromise the structure. Point measurements made to evaluate clay integrity, such as those from grid sampling or ...

1996-04-01

352

DEVELOPMENT OF PROTOTYPE TITANATE ION EXCHANGE LOADED MEMBRANES FOR STRONTIUM, CESIUM AND ACTINIDE DECONTAMINATION FROM AQUEOUS MEDIA  

International Nuclear Information System (INIS)

We have successfully incorporated high surface area particles of titanate ion exchange materials (monosodium titanate and crystalline silicotitanate) with acceptable particle size distribution into porous and inert support membrane fibrils consisting of polytetrafluoroethylene (Teflon(reg_sign)), polyethylene and cellulose materials. The resulting membrane sheets, under laboratory conditions, were used to evaluate the removal of surrogate radioactive materials for cesium-137 and strontium-90 from high caustic nuclear waste simulants. These membrane supports met the nominal requirement for nonchemical interaction with the embedded ion exchange materials and were porous enough to allow sufficient liquid flow. Some of this 47-mm size stamped out prototype titanium impregnated ion exchange membrane discs was found to remove more than 96% of dissolved cesium-133 and strontium-88 from a caustic nuclear waste salt simulants. Since ...

2008-05-30

353

Corrosion studies on selected packaging materials for disposal of high level wastes  

International Nuclear Information System (INIS)

In order to qualify corrosion resistant materials for high level waste (HLW) packagings acting as a long-term barrier in a rock salt repository, the corrosion behaviour of the preselected materials Ti 99.8-Pd, Hastelloy C4 and two unalloyed steels was investigated. The resistance of the materials to general corrosion, local corrosion and stress corrosion cracking was examined under postulated accident conditions in the repository by long-term immersion tests of up to 4 years duration and electrochemical methods. The parameters investigated were different salt brines, temperatures of 90 deg. C, 170 deg. C and 200 deg. C as well as a gamma radiation field of 10"3Gy/h (10"5rad/h). Among the materials studied, Ti 99.8-Pd exhibited the highest corrosion resistance. This material corroded at a very low rate (

1987-05-01

354

Transmutation of minor actinides in high and representative neutron fluxes: the mini-INCA and MEGAPIE projects  

Energy Technology Data Exchange (ETDEWEB)

In the framework of nuclear waste transmutation studies, the Mini-INCA project has been initiated at CEA/DSM with objectives to determine optimal conditions for transmutation and incineration of minor actinides (MA) in high intensity neutron fluxes. Our experimental tools based on alpha- and gamma-spectroscopy of the samples and the development of micro fission chambers could gather either microscopic information on nuclear reactions (total or partial cross sections for neutron capture and/or fission reactions) or macroscopic information on transmutation and incineration potentials. Neutron capture cross sections of selected actinides ({sup 241}Am, {sup 242}Am, {sup 242}Pu, {sup 237}Np) have already been measured at ILL, showing some discrepancies when compared to evaluated data libraries but in overall good agreement with recent data. The studies and possibilities offer by the MEGAPIE project to assess neutronic performances of a 1 MW ...

2003-07-01

355

Transmutation of minor actinides in high and representative neutron fluxes: the mini-INCA and MEGAPIE projects  

International Nuclear Information System (INIS)

In the framework of nuclear waste transmutation studies, the Mini-INCA project has been initiated at CEA/DSM with objectives to determine optimal conditions for transmutation and incineration of minor actinides (MA) in high intensity neutron fluxes. Our experimental tools based on alpha- and gamma-spectroscopy of the samples and the development of micro fission chambers could gather either microscopic information on nuclear reactions (total or partial cross sections for neutron capture and/or fission reactions) or macroscopic information on transmutation and incineration potentials. Neutron capture cross sections of selected actinides ("2"4"1Am, "2"4"2Am, "2"4"2Pu, "2"3"7Np) have already been measured at ILL, showing some discrepancies when compared to evaluated data libraries but in overall good agreement with recent data. The studies and possibilities offer by the MEGAPIE project to assess neutronic performances of a 1 MW spallation target ...

2003-09-01

356

The cascade of reservoirs of the ``Mayak`` Plant: Case history and the first version of a computer simulator  

Energy Technology Data Exchange (ETDEWEB)

The improvement of the ecological conditions at waste storing reservoirs is an important task of the restoration activity at Production Association (PA) ``Mayak`` (South Urals). The radionuclides mostly {sup 90}Sr, {sup 137}Cs, and chemical pollutants deposited in the reservoir water and in the bottom sediment are very dangerous sources for the contamination of Techa River below the reservoirs and the contamination of groundwater in the surrounding formations. The spreading of radioactive contaminants has both hydrogeological and the chemical features. The thermodynamic approach used to account for physical-chemical interactions between water and the bed rocks based on Gibbs free energy minimization of multicomponent system (H-O-Ca-Mg-K-Na-S-Cl-C-Sr) permitted the authors to calculate the corresponding ionic and complex species existing in the solutions, and to characterize the processes of precipitation and dissolution. The model takes into ...

1994-07-01

357

Study on upgrading of oil palm wastes to animal feeds by radiation and fermentation processing  

International Nuclear Information System (INIS)

Upgrading of oil palm empty fruit bunch (EFB), which is a main by-product of palm oil industry, to animal feeds by radiation pasteurization and fermentation was investigated for recycling the agro-resources and reducing the environmental pollution. The following results were obtained: 1) The necessary dose for pasteurization of EFB contaminated by various microorganisms including aflatoxin producing fungi was determined as 10 kGy. The chemical and biological properties of EFB were changed little by irradiation up to 50 kGy. 2) In the fermentation process, Pleurotus sajor-caju was selected as the most effective fungi and the optimum condition for fermentation was clarified. The process of fermentation in suspension was also established for the liquid seed preparation. 3) The digestibility and nutritional value of fermented products were evaluated as ruminant animal feeds and the mushroom can be produced as by-product. 4) The pilot plant named Sterifeed was built at ...

2002-10-15

358

Selective adsorption of uranium on activated charcoal from electrolytic aqueous solutions  

Energy Technology Data Exchange (ETDEWEB)

Adsorption of uranium onto various solids is important from purification, environmental, and radioactive waste disposal points of view. Adsorption of uranium on activated charcoal has been studied as a function of shaking time, amount of adsorbent, pH, concentration of adsorbate, and temperature. Uranium adsorption obeys the Langmuir isotherm. {Delta}H{degrees} and {Delta}S{degrees} were calculated from the slope and intercept of plots ln K{sub D} vs 1/T. The influence of different anions and cations on uranium adsorption has been examined. The adsorption of other metal ions on activated charcoal has been studied under specified conditions to check its selectivity; consequently, uranium was removed from Cs, Ba, Zn, and Co. More than 98% adsorbed uranium on activated charcoal can be recovered with 65 ml of 3 M HNO{sub 3} solution. A wavelength dispersive x-ray fluorescence spectrometer was used for measuring uranium concentration.

1992-02-01

359

Response of a Spent Fuel Transportation Cask to a Tunnel Fire Event  

Energy Technology Data Exchange (ETDEWEB)

The staff of the Spent Fuel Project Office at the U.S. Nuclear Regulatory Commission undertook the investigation and thermal analysis of the Baltimore tunnel fire event. This event occurred in the Howard Street tunnel, in Baltimore, Maryland, on July 18, 2001. The staff was tasked with assessing the consequences of this event on the transportation of spent nuclear fuel. This paper describes the staff's coordination with the following government and laboratory organizations: the National Transportation Safety Board (NTSB), to determine the details of the train derailment and fire; the National Institute of Standards and Technology (NIST), to quantify the thermal conditions within the tunnel; the Center for Nuclear Waste Regulatory Analysis (CNWRA), to validate the NIST evaluations, and the Pacific Northwest National Laboratory (PNNL), to assist in the thermal analysis. The results of the staff's review and analysis efforts are ...

2003-02-25

360

Reaction kinetics of fluidized bed gasification of Jordanian oil shales  

Energy Technology Data Exchange (ETDEWEB)

Trying to achieve the optimal utilization of oil shale resources, and the production of a more environmentally acceptable fuel, as well as a solid waste with a low a sulphur content, thereby reducing acidic leachates, has led to this investigation. In this article, the influences of the bed temperature and the choice of fluidizing gas on the quality and quantity of the produced fuel gas, using a continuous feed fluidized bed reactor, were investigated. The composition and calorific value of the generated gas were determined. There was a nearly linear increase in the amount of fuel gas produced as a function of temperature, reaching {approx}350 kg per 10{sup 3} kg of dry raw shale and the gross calorific value ranged from 15 to 23 MJ-kg{sup -1} with CO and H{sub 2} being the major constituents. Subsequent experiments were carried out, employing a thermogravimetric analyser under similar conditions as applied to the fluidized bed reactor. ...

2000-02-01

361

Radiation factors specifying safety in reactor compartments handling in the process of decommissioning nuclear-powered submarines  

International Nuclear Information System (INIS)

The main problems arising in decommissioning nuclear-powered submarines (NPS) relate to choosing a concept of handling reactor compartments followed by handling technology development. Reactor compartments (RC) are characterized with extremely space-saving or integral layout of large-size power equipment and systems, restricted access for dismantling, high radiation dose rates in a number of bays of RC. The above RC features pose a problem to find optimum option of RC utilization which on the one hand would be the most cost efficient, and the safest as possible on the other, i.e. dose commitments of personnel involved should be minimum, and effect on population and environment should be negligible. The main radiation factors specifying safety in RC handling at any decommissioning stage are as follows: (1) total radioactivity integrated in reactor facility (RF); (2) distribution of this radioactivity through RF equipment and structures; (3) forms the radioactivity exists in; (4) ...

1996-03-10

362

Pumps and compressors - buyers` guide 1996/`97; Pumpen und Kompressoren - Einkaufsfuehrer 1996/97  

Energy Technology Data Exchange (ETDEWEB)

The 1996/`97 buyers` guide comprises ten chapters: 1. List of suppliers; 2. Waste management, effluents, sewage systems; 3. Water supply, hydroengineering; 4. Chemistry, petrochemistry; 5. Chemical engineering; 6. Food industry, biotechnology; 7. Paper and cellulose industry; 8. Natural gas industry, natural gas supply; 9. Power plant engineering, power systems, district heating; 10. Air conditioning and refrigeration engineering. (orig.) [Deutsch] Der vorliegende Einkaufsfuehrer 1996/97 ist in zehn Kapiteln gegliedert. Diese sind: 1. Firmenverzeichnis 2-11 2. Entsorgungs-/Abwassertechnik, Klaeranlagen 12-15 3. Wasserversorgung, Wassertechnik 16-18 4. Chemie, Petrochemie 19-22 5. Verfahrenstechnik 23-26 6. Lebensmittelindustrie, Biotechnik 27-29 7. Papier-, Zeluloseindustrie 30-31 8. Erdgasindustrie, -versorgung 32 9. Kraftwerkstechnik, Energieanlagen, Fernwaerme 33-34 10. Kaelte-/Klimatechnik 35-36. (orig.)

1996-12-01

363

Programmed improvements of the alternating gradient synchrotron complex at Brookhaven National Laboratory, Upton, New York. Environmental assessment  

Energy Technology Data Exchange (ETDEWEB)

The purpose and need for DOE to undertake the actions described in this document are to improve the efficiency of the Alternating Gradient Synchrotron (AGS) complex. Benefits would include optimization of the AGS scientific program, increased high-energy and nuclear physics experimentation, improved health and safety conditions for workers and users, reduced impact on the environment and the general public, energy conservation, decreased generation of hazardous and radioactive wastes, and completion of actions required to permit the AGS to be the injector to the Relativistic Heavy Ion Collider (RHIC)., Improved efficiency is defined as increasing the AGS`s capabilities to capture and accelerate the proton intensity transferred to the AGS from the AGS booster. Improved capture of beam intensity would reduce the beam losses which equate to lost scientific opportunity for study and increased potential for radiation doses to workers and the general ...

1994-03-01

364

Process energy management  

Energy Technology Data Exchange (ETDEWEB)

In many facilities, energy management is simply a matter of managing the energy required for lighting and space conditioning. In many others, however, energy management is much more complex and involves large motors and controls, industrial insulation, complex combustion monitoring, unique steam distribution problems, significant amounts of waste heat, etc. Typical facilities offering large energy management opportunities include industrial facilities, large office and commercial operations, government institutions such as schools, hospitals and prisons. Such facilities generally have specialized industrial, commercial or institutional processes that incorporate many of the concepts covered in other chapters. These processes require thorough analytical evaluations to determine the appropriate energy-saving measures. This chapter provides some examples. In this chapter the authors present a suggested procedure for process energy improvement. ...

1994-12-31

365

Phytoremediation : an industry partner's perspective  

International Nuclear Information System (INIS)

As part of their corporate policy on environmental protection, Chevron, has taken an approach to work collaboratively with other industry members, universities and government agencies in phytoremediation research. The petroleum industry is interested in the integration of phytoremediation with the many biotechnology treatment technologies currently being used by the industry. Phytoremediation is a complex technology that does not just transfer wastes to another site, but offers in-situ final use and disposal treatment at sites anywhere in the world. Sites for potential remediation range from abandoned large refineries, chemical plants, or small urban gas stations. Research has focused on the cleanup of metals and hydrocarbons in diverse types of soil, water and groundwater conditions. This includes research into remediation of petroleum contaminants such as total petroleum hydrocarbon (TPH), polynuclear aromatic hydrocarbons as well as benzene ...

366

Labor market trends for nuclear engineers through 2000  

Energy Technology Data Exchange (ETDEWEB)

Throughout most of the 1980s, both private organizations and government agencies were concerned about the availability of an adequate supply of qualified nuclear engineers. This concern was primarily the result of a number of nuclear engineering academic programs being eliminated coupled with a continuous decline in graduate and undergraduate enrollments and degrees. By the early 1990s, the number of degrees and available supply had declined to new lows, but cutbacks in funding for the nuclear weapons program and nuclear energy R&D, and in hiring by the electric utility industry, offset in large measure the declining supply. Recently, concerns about environment and waste management and about nuclear safety have again generated questions about the adequacy of supply of qualified personnel for nuclear energy activities. This report briefly examines the nuclear engineering labor market. Trends in employment, new graduates, job openings, and salaries are reviewed ...

1995-01-01

367

Investigation of the impact of electricity rate and mix on optimum green building design  

Energy Technology Data Exchange (ETDEWEB)

The basic principle of the green building philosophy is to design buildings that consider environmental performance. Residential and commercial buildings in Canada consume about 30 per cent of the total secondary energy use and are responsible for approximately 29 per cent of carbon dioxide equivalent greenhouse gas emissions and many other wastes. An optimization model was developed which minimizes life cycle cost and life cycle environmental impact. The model distinguishes different energy sources and incorporates their impacts, such as resource depletion, global warming and acidification. The model also considers design variables such as window type, orientation, building orientation, window-to-wall ratio, wall type and roof type. The model can be used to identify optimum green building designs for given conditions. The model uses expanded cumulative exergy consumption as the indicator for life cycle environmental performance. As such, it ...

2004-07-01

368

Interactions between creep and corrosion in Alloy 800  

Energy Technology Data Exchange (ETDEWEB)

Metallic components within or immediately adjacent to gasifiers, such as gas distributors, thermowells, transfer lines, and cyclones, are subjected to severe of temperature, pressure, and hostile multicomponent gas environments. Metallic heat exchangers/waste-heat boilers resistant to sulfidation, corrosion. and erosion in low- and medium-Btu gas environments are essential components in large-scale gasification schemes, in both dry ash and slogging type gasifiers. Components, in general. must be resistant to corrosion, erosion, and high-temperature creep. A substantial data base is needed on the mechanical properties of materials exposed to complex gas environments to provide a more viable basis for establishing long-term reliability of components. This work examines high-temperature creep of Alloy 800, a high-chromium alloy widely used in coal conversion systems, after exposure to oxygen and oxygen/sulfur mixed-gas environments over a wide temperature range. In ...

1994-04-01

369

Identification of environmental RD D needs  

Energy Technology Data Exchange (ETDEWEB)

The objective of this project was to identify needs for environmental research development and demonstration projects that have the potential to improve the performance of oil and gas exploration, drilling, and production technologies for maximum recovery of domestic petroleum resources under optimal environmental and economic conditions. To achieve this objective several areas of work were addressed. The first task was to compile as much related data as possible. This was achieved by literature searches of a number of petroleum-related data bases. After acquiring sufficient background on environmental and economical areas that should be expanded, experts who are knowledgeable in these areas were contacted to further define specific issues. More than 33 identified areas were submitted to an in-house panel at NIPER to assure that the final environmental research demonstration and development needs that were selected to be expanded were unbiased and worthy of ...

1991-09-01

370

Groundwater travel time uncertainty analysis. Sensitivity of results to model geometry, and correlations and cross correlations among input parameters  

Energy Technology Data Exchange (ETDEWEB)

This study examines the sensitivity of the travel time distribution predicted by a reference case model to (1) scale of representation of the model parameters, (2) size of the model domain, (3) correlation range of log-transmissivity, and (4) cross correlations between transmissivity and effective thickness. The basis for the reference model is the preliminary stochastic travel time model previously documented by the Basalt Waste Isolation Project. Results of this study show the following. The variability of the predicted travel times can be adequately represented when the ratio between the size of the zones used to represent the model parameters and the log-transmissivity correlation range is less than about one-fifth. The size of the model domain and the types of boundary conditions can have a strong impact on the distribution of travel times. Longer log-transmissivity correlation ranges cause larger variability in the predicted travel times. ...

1985-03-01

371

GENERIC ENZYME TECHNOLOGY FOR IMPROVED PAPER RECYCLING  

Environmental Research Database

Objectives- Investigate the potential for the use of enzymes to bring about improvements in the recycling of recovered waste paper sources~%~~%~- Optimise enzyme formulations and process conditions to maximise benefits. - Produce recovered fibre at lower energy and chemical costs than is currently achievable using 'classical' de-inking techniques.~%~~%~- Improve recycled fibre quality and~%~~%~- All of the above will allow a greater use of recovered paper resources, which would otherwise be diposed of by [continued...]DescriptionThe project proposes to carry out an initial literature review to update the consortium on the currently available publications relating to the use of enzymes in de-inking.. This will be followed by an intensive laboratory study in an upgraded facility which will allow enzyme formulations and mechanisms to be studied. This work will also eliminate the need for an ...

2003-01-05

372

Experimental study of the premixed combustion within the nonhomogeneous porous ceramic media  

Energy Technology Data Exchange (ETDEWEB)

An experimental investigation of premixed methane-air combustion within the one-dimensional porous ceramic burners for various burner configurations is presented. The burner is nonhomogeneous because of different pore size ceramic block used in different section of the burner. Therefore, the thermophysical and transport properties are nonuniform along the burner core length. The burners are constructed of partially stabilized zirconia. The CO and NO{sub x} emissions, flame speed, and flame stability are examined and compared at lean equivalence ratios for five different burner configurations. The sandwich-structured burner has very favorable flame stabilizing characteristic due to the radiation reflecting region. While the combustion proceeds at faster rate than other burner configurations, the radiation reflecting region and the exit surface have low temperature. Thus the NO{sub x} emission can be kept at the same low level as the other burner configurations exhibit., It is found that ...

1996-12-01

373

Experience on resin pyrolysis  

International Nuclear Information System (INIS)

The Swedish State Power Board has together with Nukem, Hanau, West-Germany carried out pyrolysis o powder resins in a pilot plant with a capacity of about 30 kg/hr. The pyrolysis reactor with its afterburner and offgas scrubber system has been operated under steady state condition. About 2200 kg resins have been pyrolysed under November-December 1983 and the decontamination factor for Cs has been measured. Solidification of the residues from the pyrolysis reactor and scrubber water solutions has been carried out and various recipes with cement have been tested. The pyrolysis process has high decontamination factors and no offgas problems as the operating temperature of the reactor is Low. The residues from the reactor are chemically dead and can not cause swelling problems. Compared with a normal cementation process the final waste volume will be reduced with a factor of 4 if also the scrubber water after neutralization is solidified. The ...

374

Enhancement of the decontamination factor for liquid radioactive waste and other radioactive materials  

International Nuclear Information System (INIS)

Decommissioning of radiological and nuclear installations is for this century the new challenge. One of the performance criteria is the reduction of total quantities of radioactive materials (liquid or solid) arising from dismantling and decontamination of radiological and nuclear installations. In this work we present a new application of the water soluble polymers used as: - flocculation agents in treatment and conditioning process within the management of radioactive liquid materials; - strippable coatings on solid materials based on the water soluble polymers. The parameters of water soluble polymers made in our Institute by radiation processing have been analysed, namely the molecular average weight, composition, and efficiency of utilization of these polymeric materials as well as the content of ash, additives, decontamination factor, consumption per surfaces/liter, corrosion aspects, compatibility with various surfaces (of metal, concrete, plastics, etc). ...

2003-10-20

375

Detection of concealed mercury with thermal neutrons  

Energy Technology Data Exchange (ETDEWEB)

In the United States today, governments at all levels and the citizenry are paying increasing attention to the effects, both real and hypothetical, of industrial activity on the environment. Responsible modem industries, reflecting this heightened public and regulatory awareness, are either substituting benign materials for hazardous ones, or using hazardous materials only under carefully controlled conditions. In addition, present-day environmental consciousness dictates that we deal responsibly with legacy wastes. The decontamination and decommissioning (D&D) of facilities at which mercury was used or processed presents a variety of challenges. Elemental mercury is a liquid at room temperature and readily evaporates in air. In large mercury-laden buildings, droplets may evaporate from one area only to recondense in other cooler areas. The rate of evaporation is a function of humidity and temperature; consequently, different parts of a ...

1994-08-18

376

Continuous fermentative hydrogen production in different process conditions  

Energy Technology Data Exchange (ETDEWEB)

This paper reported on a study in which hydrogen was produced by fermentation of biomass. A continuous process using a non-sterile substrate with a readily available mixed microflora was used on heat treated digested sewage sludge from a wastewater treatment plant. Hydrogen was produced from waste sugar at a pH of 5.2 and a temperature of 37 degrees C. An experimental setup of three 5.5 L working volume continuously stirred tank reactors (CSTR) in different stirring speeds were constructed and operated at 7 different hydraulic retention times (HRTs) and different organic loading rates (OLR). Dissolved organic carbon was examined. The results showed that the stirring speed of 135 rpm had a beneficial effect on hydrogen fermentation. The best performance was obtained in 135 rpm and 8 h of HRT. The amount of gas varied with different OLRs, but could be stabilized on a high level. Methane was not detected when the HRT was less than 16 h. The study identified the ...

2010-07-01

377

Combined cycle power plant with integrated low temperature heat (LOTHECO)  

International Nuclear Information System (INIS)

The major driver to enhance the efficiency of the simple gas turbine cycle has been the increase in process conditions through advancements in materials and cooling methods. Thermodynamic cycle developments or cycle integration are among the possible ways to further enhance performance. The current paper presents the possibilities and advantages from the LOTHECO natural gas-fired combined cycle concept. In the LOTHECO cycle, low-temperature waste heat or solar heat is used for the evaporation of injected water droplets in the compressed air entering the gas turbine's combustion chamber. Following a description of this innovative cycle, its advantages are demonstrated by comparison between different gas turbine power generation systems for small and large-scale applications, including thermodynamic and economic analysis. A commercial gas turbine (ALSTOM GT10C) has been selected and computed with the heat mass balance program ENBIPRO. The results ...

2004-08-01

378

Ameliorating effects of industrial sugar residue on the Jales gold mine spoil (NE Portugal) using Holcus lanatus and Phaseolus vulgaris as indicators  

Energy Technology Data Exchange (ETDEWEB)

A residue of the sugar industry can be used in revegetation programs on metal contaminated sites. - Phytostabilisation of bare heavily contaminated substrate, such as abandoned mine sites, is considered a very appropriate technology in order to diminish erosion and dispersion of contaminants into the surroundings. In this short-term pot study, application of industrial sugar residue (ISR), a waste product of the sugar industry, proved to ameliorate spoils conditions for plant performance by elevating pH and immobilising several metals. Although arsenate concentrations were positively correlated to spoil pH and spoil treatment with ISR mobilised As, growth of both Phaseolus vulgaris and Holcus lanatus improved significantly after applications of 3.75 g ISR kg{sup -1} dry spoil. Nutrient uptake from the substrate, with the exception of potassium, was elevated by ISR. As a remediation technique ISR application could be effective although in ...

2003-09-01

379

Advances on experimental techniques for the characterization of THM behaviour of bentonite  

Energy Technology Data Exchange (ETDEWEB)

The design of high level radioactive waste (HLW) repositories in deep geological media in which bentonite clay is proposed as a sealing material leads to the need of further studying the behaviour of highly compacted expansive soils when subjected to mechanical, hydraulic and thermal changes. Laboratory tests may help to understand the processes that take place in the clay barrier under simple and controlled conditions and to develop the governing equations. The laboratory tests enable to isolate the different processes, making their interpretation easier, and provide with fundamental data concerning the parameters to be used in the models. The extremely low permeability of these materials, their avidity for water (high suction) and their high swelling capacity make necessary the modification of the conventional laboratory techniques and procedures to determine basic physical parameters. The main hydraulic properties of the barrier to be ...

2005-07-01

380

Adjoint sensitivity theory for steady-state ground-water flow  

Science.gov (United States)

In this study, adjoint sensitivity theory is developed for equations of two-dimensional steady-state flow in a confined aquifer. Both the primary flow equation and the adjoint sensitivity equation are solved using the Galerkin finite element method. The developed computer code is used to investigate the regional flow parameters of the Leadville Formation of the Paradox Basin in Utah and the Wolcamp carbonate/sandstone aquifer of the Palo Duro Basin in the Texas Panhandle. Two performance measures are evaluated, local heads and velocity in the vicinity of potential high-level nuclear waste repositories. The results illustrate the sensitivity of calculated local heads to the boundary conditions. Local velocity-related performance measures are more sensitive to hydraulic conductivities. The uncertainty in the performance measure is a function of the parameter sensitivity, parameter variance and the correlation between parameters. Given a parameter ...

1983-11-01

381

Abrasive waterjet cutting of high purity uranium metal: Topical report  

Science.gov (United States)

The Abrasive Waterjet Cutting process was evaluated to determine if the equivalent could be utilized for cutting uranium metal at the Feed Materials Production Center (FMPC). In the process, a thin stream of ultrahigh pressure water carried grit material through a designated piecepart. In order to be acceptable for use at the FMPC, the equipment must be cost effective, minimize waste, and be adaptableto operating in an enclosure, and improve health and safety conditions. Observation of the cutting process showed that health and safety aspects could be optimized with an enclosed ventilated system. Also the equipment can be easily automated. The cutting action produced sparks similar to the sparks caused by a grinding operation. The sparks are captured in a water container under the workpiece that not only catches the sparks, but also serves to dissipiate the stream of water and residues produced by the cut. Metallographic tests performed on the ...

1988-01-01

382

The carrying out process of Kyoto Protocol in Italy. Methods, scenarios and policy evaluation; Il processo di attuazione del Protocollo di Kyoto in Italia. Metodi, scenari e valutazione di politiche e misure  

Energy Technology Data Exchange (ETDEWEB)

This paper reports some technical contributes related to the Kyoto Protocol and its application in Italian decision making policy. [Italian] Il presente volume raccoglie una decina di contributi tecnici originariamente preparati o commissionati dall'ENEA, Ente Nazionale per le Nuove Tecnologie, l'Energia e l'Ambiente, in vista della Conferenza Nazionale Energia e Ambiente. Questa fotografia di una situazione in rapida evoluzione e' stata preparata da esperti del settore che contribuiscono a redigere il materiale tecnico di base utilizzato dai negoziatori nazionali durante le trattative internazionali e dai responsabili nazionali per avviare il processo di presa di decisioni in materia.

2000-07-01

383

Quarkonia and QGP studies  

CERN Document Server

We summarize results of recent studies of heavy quarkonia correlators and spectral functions at finite temperatures from lattice QCD and systematic T-matrix studies using QCD motivated finite-temperature potentials. We argue that heavy quarkonia dissociation shall occur in the temperature range $1.2 \\le T_d/T_c \\le 1.5$ by the interplay of both screening and absorption in the strongly correlated plasma medium. We discuss these effects on the quantum mechanical evolution of quarkonia states within a time-dependent harmonic oscillator model with complex oscillator strength and compare the results with data for $R_{\\rm AA}/R_{\\rm AA}^{\\rm CNM}$ from RHIC and SPS experiments. We speculate whether the suppression pattern of the rather precise NA60 data from In-In collisions may be related to the recently discovered X(3872) state. Theoretical support for this hypothesis comes from the cluster expansion of the plasma Hamiltonian for heavy ...

2011-01-01

384

Paramagnetic susceptibility of nonstoichiometric fluorides with the fluorite-type structure  

Energy Technology Data Exchange (ETDEWEB)

Magnetic properties of single crystals of nonstoichiometric fluorides M[sub 1-x]R[sub x]F[sub 2+x] (M = Ca, Sr, Ba; R = Ce, Pr, Nd, Gd, Ho, Er, Tm, Yb; with 0.05 [le] x [le] 0.28) with the fluorite-type structure have been studied for the first time. The magnetic susceptibility was measured using a Faraday balance in the 15-300 K temperature range. The samples are paramagnetic following the Curie-Weiss law. The values of paramagnetic Curie temperatures and effective magnetic moments of rare-earth ions have been found. Deviations of the temperature dependence of magnetic susceptibility from the Curie-Weiss law are observed for some nonstoichiometric fluorides at temperatures ranging from 60 to 85 K. Possible reaons for these deviations are discussed. Measurements of magnetic susceptibility provide an effective technique for a rapid and accurate determination of the concentration of rare-earth ions in nonstoichiometric fluorides.

1993-01-01

385

Indentation modulus and hardness in heteroepitaxial Al{sub x}Ga{sub 1{minus}x}P films  

Energy Technology Data Exchange (ETDEWEB)

Al{sub x}Ga{sub 1{minus}x}P layers (0 {le} x {le} 0.7), with thicknesses of {ge}1 {micro}m were grown on Si (100) wafers by metal-organic molecular beam epitaxy (MOMBE) at 450 C. Transmission electron micrographs of the single crystal films revealed that the microstructure contains stacking faults and microtwins especially near the interface as well as both threading and misfit dislocations. Hardness and elastic modulus were measured using a Nanotest 500 indenter, which can probe the film properties without influence from the substrate. The hardness H varies linearly according to (11.8 {minus} 2.3x) GPa. The absence of alloy hardening is due to the fact that there is no difference in atomic size of Al and Ga. The indentation modulus E/(1{minus}v{sup 2}) decreases monotonically from 136 GPa for GaP to 129 GPa for Al{sub 0.7}Ga{sub 0.3}P and bows only slightly (about 2%) below the straight line of linear interpolation.

1997-05-01

386

Field-induced valence transition of Eu(Pd{sub 1{minus}x}Pt{sub x}){sub 2}Si{sub 2}  

Energy Technology Data Exchange (ETDEWEB)

The magnetic susceptibility and high-field magnetization have been measured for the intermediate valence system Eu(Pd{sub 1{minus}x}Pt{sub x}){sub 2}Si{sub 2} with 0{le}x{le}0.15. A first-order valence transition is observed for all the compounds under high field of 100 T at low temperatures. This valence transition is of first order accompanied with a large hysteresis, which is in contrast to a continuous valence change against temperature. Based on the interconfigurational fluctuation (ICF) model, the temperature- and field-induced valence transitions are discussed. It is found that a first-order valence transition can be induced by magnetic field, even if the system shows a continuous valence transition against temperature. Metamagnetic behavior at finite temperatures is also understood qualitatively by the ICF model. {copyright} {ital 1997} {ital The American Physical Society}

1997-05-01

387

Dosimetry in dental radiology. Dentascan spiral CT versus panoramic radiography; Dosimetria nella radiologia odontostomatologica: confronto tra tomografia computerizzata spirale e ortopantomografia  

Energy Technology Data Exchange (ETDEWEB)

The study compares the doses absorbed by the dentomaxillary area in spiral CT and panoramic examinations. The dose measurements demonstrate that patients receive smaller doses with panoramic radiography than with spiral CT with Dentascan. After following for some variations from instrumental differences, they are in substantial agreement with literature data. Further investigations are needed considering the radiobiological risk related to the growing spread of Dentascan examinations. [Italian] Questo lavoro intende confrontare le dosi assorbite nel distretto dento-mascellare, con le due principali tecniche utilizzate in questo campo: TC spirale e ortopantomografia. Emerge come l'esame panoramico delle arcate dentarie eseguito con l'ortopantomografo comporti la'ssorbimento di dosi inferiori rispetto a quelle dell'esame TC spirale con programma Dentascan. Questi dati, pur essendo soggetti a ...

1999-05-01

388

Cosmic-Ray Nuclei, Antiprotons and Gamma-rays in the Galaxy: a New Diffusion Model  

CERN Document Server

We model the transport of cosmic ray nuclei in the Galaxy by means of a new numerical code. Differently from previous numerical models we account for a generic spatial distribution of the diffusion coefficient. We found that in the case of radially uniform diffusion, the main secondary/primary ratios (B/C, N/O and sub-Fe/Fe) and the modulated antiproton spectrum match consistently the available observations. Convection and re-acceleration do not seem to be required in the energy range we consider: $1 \\le E \\le 10^3$ GeV/nucleon. We generalize these results accounting for radial dependence of the diffusion coefficient, which is assumed to trace that of supernova remnants. While this does not affect the prediction of secondary/primary ratios, the simulated longitude profile of the diffuse $\\gamma$-ray emission is significantly different from the uniform case and may agree with EGRET measurements without invoking {\\it ad hoc} assumptions on ...

2008-01-01

390

Waste management facilities cost information for hazardous waste. Revision 1  

Energy Technology Data Exchange (ETDEWEB)

This report contains preconceptual designs and planning level life-cycle cost estimates for managing hazardous waste. The report`s information on treatment, storage, and disposal modules can be integrated to develop total life-cycle costs for various waste management options. A procedure to guide the US Department of Energy and its contractor personnel in the use of cost estimation data is also summarized in this report.

1995-06-01

391

Waste Diversion | Greening EPA | US EPA  

Wastenet

...diversion generates a host of environmental, financial, and social benefits, including conserving energy, reducing disposal costs, and reducing the burden on landfills and other waste disposal methods . Waste Diversion at EPA For many years, EPA has established waste diversion goals that exceed current federal requirements. EPA ...

392

Utilization of plastic wastes in a blast furnace - a contribution to ecological and economical recycling of plastic wastes; Kunststoffverwertung im Hochofen - ein Beitrag zum oekologischen und oekonomischen Recycling von Altkunststoffen  

Energy Technology Data Exchange (ETDEWEB)

This article describes the utilization of plastic wastes in a blast furnace. The plastic waste is a substitution for petroleum and coal as a raw material for synthesis gas production. The synthesis gas is the reducing agent in the blast furnace for the reduction of iron ores. You can find here an ecological and economical analysis of this process in comparison to the utilization of petroleum and coal. (SR)

1996-12-31

396

Resources | Environment Knowledge Hub  

Wastenet

... MUNICIPAL SOLID WASTES (MANAGEMENT AND HANDLING) RULES, 2000 Plastic Bag ban in Dhaka City, Bangladesh Private Sector Participation in Municipal Solid Waste Management SKAT 2000 TECHNICAL GUIDELINES ON MUNICIPAL SOLID WASTE MANAGEMENT Hazardous Waste Management Unit, Environmental Pollution Control Division, Central Environmental Authority, Sri Lanka 2004 Subregional ...

397

Request for interim approval to operate 218-E-12B Trench 94 as a chemical waste landfill for disposal of polychlorinated biphenyl wastes in submarine reactor compartments. Revision 1.  

Science.gov (United States)

This request is submitted to seek interim approval to operate a chemical waste landfill for the disposal of polychlorinated biphenyl (PCB) waste. Interim approval is requested for a period not to exceed 5 years. This request covers only the disposal of sm...

1992-01-01

402

Oil refinery waste disposal methods, quantities and costs, 1993 survey  

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the information gathered by CONCAVE in a 1993 survey of waste generation and disposal by the oil refineries in Western Europe. The survey covered the types of waste produced, their quantities, disposal routes and costs of disposal. The results are compared with those from a 1986 survey, but because of the increased numbers of refineries reporting, comparison is difficult. The survey revealed wide variations in disposal costs depending on waste type and local circumstances.

1995-06-01

404

Model analysis of an inter-industrial and inter-regional waste recycling system in Japan  

Energy Technology Data Exchange (ETDEWEB)

In this study, we investigate an inter-industrial and inter-regional recycling system for industrial waste by the cement industry in Japan. We develop a linear programming model that represents cement production processes and waste transportation of all cement factories in Japan. We simulate cost and CO{sub 2}-minimizing systems. The result implies that making waste transportation more efficient in cost is an effective means for CO{sub 2} reduction. (author)

2007-04-15

405

Methane fermentation of agricultural wastes and domestic animal's wastes  

Energy Technology Data Exchange (ETDEWEB)

Cattle and pig wastes, orange peels, compost, and grain husks were hydrolyzed in an alkaline medium to investigate the CH4 generation capacity. The respective CH4 production capacities from pig wastes and rice hulls were approximately 1 and approximately 0.1 L/g. The CH4 produced can be used to supplement energy requirements of farms.

1981-01-01

411

Idaho National Engineering Laboratory Nonradiological Waste Management Information for 1992 and record to date  

Energy Technology Data Exchange (ETDEWEB)

This document provides detailed data and graphics on airborne and liquid effluent releases, fuel oil and coal consumption, water usage, and hazardous and mixed waste generated for calendar year 1992. This report summarizes industrial waste data records compiled since 1971 for the Idaho National Engineering Laboratory (INEL). The data presented are from the INEL Nonradiological Waste Management Information System.

1993-08-01

412

GS1 - radiological protection objectives for the disposal of solid radioactive wastes  

Energy Technology Data Exchange (ETDEWEB)

A summary is given of the 1983 NRPB-GS1 Report on the 'Radiological protection objectives for the disposal of solid radioactive wastes'. The two principal difficulties in applying the ICRP system of dose limitation to some solid waste disposal methods are outlined. Despite these difficulties three radiological protection objectives for waste disposal were recommended based on the same fundamental principle as ICRP recommendations.

1984-01-01

413

Estimation of animal and olive solid wastes in Jordan and their potential as a supplementary energy source: An overview  

Energy Technology Data Exchange (ETDEWEB)

Biomass is a potential source of energy that can reduce our dependency on oil as the main source of energy. In addition to municipal solid waste, animal and olive wastes are the main sources of organic waste in Jordan. In 2005, there were more than 2.4 million heads of sheep, about 72 thousand cows, and 40 million hens being raised in farms distributed in all governorates of Jordan. These animals produce 5.3 million tons (as exerted) of solid waste per year. If these quantities can be effectively collected they may constitute a valuable source of energy. This paper is aiming to estimate the amounts of animal and solid wastes generated in Jordan and their energy potential. The total amount of BOD from animal waste is estimated at 200,000 tons per year. Significant quantities of organic waste can also be collected from olive mills distributed ...

2010-10-15

414

Environmental assessment of coal waste mounds in Japan using remote sensing techniques  

Energy Technology Data Exchange (ETDEWEB)

Focuses on the application of remote sensing techniques to the study of coal waste mounds. The situation at the coal waste mounds in Fukuoka, Japan is cited. Guidelines on film parameters, photographic keys and tasks required to inventory, monitor and manage coal waste mounds in Japan are addressed. Application of photogrammetry, remote sensing, aerial photography and satellite imagery techniques in monitoring spoil banks is reviewed. Applicability of the techniques is discussed. 24 refs.

1993-01-01

415

Energy recovery from waste by use of fluidized-bed technology  

Energy Technology Data Exchange (ETDEWEB)

Revolving type fluidized-bed technology, developed by Ebara Corp., is installed in more than 100 facilities worldwide. The technology is applied for waste, coal and in situations where a conventional fluidized bed is difficult to use. Waste and/or coal can be treated and valuable energy can be recovered from a non-renewable source. This paper describes the application of the revolving fluidized bed for waste, coal and tyres.

1999-07-01

416

EVALUATION OF RISKS AND WASTE CHARACTERIZATION REQUIREMENTS FOR THE TRANSURANIC WASTE EMPLACED IN WIPP DURING 1999  

Energy Technology Data Exchange (ETDEWEB)

Specifically this report: 1. Compares requirements of the WAP that are pertinent from a technical viewpoint with the WIPP pre-Permit waste characterization program, 2. Presents the results of a risk analysis of the currently emplaced wastes. Expected and bounding risks from routine operations and possible accidents are evaluated; and 3. Provides conclusions and recommendations.

2000-05-01

418

Decommissioning of facility for use of radioisotopes on waste management and disposal facility  

Energy Technology Data Exchange (ETDEWEB)

All the tests have been finished up in the Waste Management and Disposal Facility which has been used for the safety tests of solidified radioactive waste on sea dumping disposal. The decommissioning of this facility was performed for use of radioisotopes. This report describes the plan on decommissioning of facility for use of radioisotopes, the contamination checking methods and measurement of radioactivity, the fore case and practice for amount of generated radioactive wastes, the operation procedures for dismantlement, the safety measures, the expenses for decommissioning and so on. (author)

1999-09-01

420

Characterisation of long-lived low and intermediate-level radioactive wastes in the Nordic Countries  

International Nuclear Information System (INIS)

The present report is final report from a study on characterisation of radioactive waters in the Nordic countries. The study has mainly been focused on long-lived low and intermediate level radioactive waste. Methods to measure or estimate the activity content and the general composition are discussed. Recommendations are given regarding characterisation of waste under treatment and characterisation of already produced waste packages. (au).

2005-01-01

421

CONVERTING WASTE  

Wastenet

condenser, gas refiner, oil (gas) storage tank and dual fuel engine

422

BC  

Wastenet

criteria which would constitute environmentally sound management of mobile phone waste in accordance with the Basel Convention;

423

BC  

Wastenet

all Certified ESM facilities capable of receiving used mobile phone waste from non-Annex VII countries.

424

Achievements and Perspectives of the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management  

International Nuclear Information System (INIS)

The Joint Convention on the Safety of Spent Fuel management and on the Safety of Radioactive Waste Management is the first legal instrument to directly address the safety of spent fuel and radioactive waste management on a global scale. The Joint Convention entered into force in 2001. This paper describes its process and its main achievements to date. The perspectives to establish of a Global Waste Safety Regime based on the Joint Convention are also discussed. (authors)

426

1993 Annual report on waste generation and waste minimization progress as required by DOE Order 5400.1, Hanford Site  

International Nuclear Information System (INIS)

More important than waste generation numbers, the pollution prevention and waste minimization successes achieved at Hanford in 1993 have reduced waste and improved operations at the Site. Just a few of these projects are: A small research nuclear reactor, unused and destined for disposal as low level radioactive waste, was provided to a Texas University for their nuclear research program, avoiding 25 cubic meters of waste and saving $116,000. By changing the slope on a asphalt lot in front of a waste storage pad, run-off rainwater was prevented from becoming mixed low level waste water, preventing 40 cubic meters of waste and saving $750,000. Through more efficient electrostatic paint spraying equipment and a solvent recovery system, a paint shop reduced hazardous waste by 3,500 kilograms, saving ...

427

Understanding and profitably managing customer loyalty  

British Library Electronic Table of Contents (United Kingdom)

Purpose - The purpose of the paper is to draw together the salient issues surrounding customer loyalty and customer relationship management (CRM) into a single coherent discussion. Various schools of academic thought are examined. The paper concludes with practical implications for managers. Design/methodology/approach - The literature surrounding customer loyalty, customer satisfaction, effective CRM and managing loyalty in a profitable manner are all reviewed. The paper allows managers to consider a wide range of material in the context of their business. Findings - The need for businesses to retain customers is an important issue in today's global marketplace. To retain customers, a business must forge loyal and long-term relationships with profitable customers. Reasons why customers le...

2008-01-01

428

Thermodynamic Model of Aluminum Combustion in SDF Explosions  

Energy Technology Data Exchange (ETDEWEB)

Thermodynamic states encountered during combustion of Aluminum powder in Shock-Dispersed-Fuel (SDF) explosions were analyzed with the Cheetah code. Results are displayed in the Le Chatelier diagram: the locus of states of specific internal energy versus temperature. Accuracy of the results was confirmed by comparing the fuel and products curves with the heats of detonation and combustion, and species composition as measured in bomb calorimeter experiments. Results were fit with analytic functions u = f(T) suitable for specifying the thermodynamic properties required for gas-dynamic models of combustion in explosions.

2006-06-19

429

The regional control of the canadian energy production; Le contraste provincial de la production energetique canadienne  

Energy Technology Data Exchange (ETDEWEB)

This document provides information and presents data on the energy situation in many regions of Canada. The first part deals with the petroleum and the bitumen shales of Alberta (reserves, exploitation and production, environmental impacts), the second part discusses with the hydroelectricity choice of Quebec and the 2004 crisis. The nuclear situation of Ontario is presented in the third part (nuclear park, programs, uranium reserves, research and development on Candu reactors), while the fourth part deals with the renewable energies (wind power and biomass). The canadian situation facing the Kyoto protocol is discussed in the last part. (A.L.B.)

2004-12-01

430

The oil at 50$: reserves depletion or OPEC revenge?; Le petrole a 50$: epuisement des reserves ou revanche de l'OPEP?  

Energy Technology Data Exchange (ETDEWEB)

Although the oil price is still far from its historical maximum, the oil market is today in crisis. To explain this situation the author discusses the nature of the supply constraints. The reserves are today better known and so more plentiful than at a previous period of the oil history and the russian production since 2004 is stagnating. The main factor seems to be the OPEC policy and in particular the will of limiting the oil production to defend upper prices. (A.L.B.)

2005-06-15

431

Surveillance and control. A new edition of the BETCGB guidebook for the control of dams in exploitation; Surveillance et controle. Une nouvelle edition du guide du BETCGB pour le controle des barrages en exploitation  

Energy Technology Data Exchange (ETDEWEB)

The French office for technical studies and control of big dams (BETCGB), has recently reedited the `guidebook for the control of dams in exploitation`. The aim of this document is to provide to the regional directions of industry, research and environment (DRIRE) a methodological help for their control actions of hydroelectric dams granted for exploitation. It comprises 6 chapters dealing with: the different type of dams, the inspection, the surveillance, the floods evacuation, the flood instructions, and the particular emergency plans. (J.S.)

1998-12-31

432

Radiology of facial injury  

Energy Technology Data Exchange (ETDEWEB)

The authors present a guide to the imaging of facial fractures. It is illustrated with conventional radiographs and computed tomograms; the magnetic resonance images primarily suggest the potential applications of this technique. This book provides a source of imaging information on facial trauma. A section on pertinent anatomy is followed by a systematic discussion of the common isolated and complex facial fractures. Perspectives are offered on some commonly seen but infrequently described relationships, such as the tripod-LeFort II association. Consideration is also given to related soft-tissue injuries. The book includes a brief chapter on the type and utility of supplementary imaging studies in the evaluation of those intracranial injuries that may occur concurrently.

1988-01-01

433

Principles for occupational exposure control; Principes pour le controle des expositions professionnelles  

Energy Technology Data Exchange (ETDEWEB)

A major component of the 1990 recommendations of ICRP (ICRP, 1991a) was the revision of the dose limits. But other changes were introduced which necessitated a review of earlier guidance. In particular, ICRP set up a Task Group in 1993 to prepare a report on the principles for the protection of workers. The report was adopted in 1997 and has now been published as ICRP Publication 75 (ICRP, 1997). It is for others to judge the real significance of the guidance provided; what follows are some of the main points. (author)

1997-10-01

434

Penetrants for hot surfaces in welding inspection: experimental work and first results; Penetrants pour le controle de surfaces chaudes lors du soudage: etude experimentale et premiers resultats obtenus  

Energy Technology Data Exchange (ETDEWEB)

Preliminary results of studies into penetrant testing at high surface temperature (up to 200 deg.C), are presented. Tests were performed to assess the effectiveness of red dye penetrants using Al and NiCr samples containing artificial as well as natural discontinuities. The test results will be used in due course to formulate a specification for non-destructive testing procedure qualification at non-standard (i.e. outside 16-52 deg.C) temperatures.

2000-04-01

435

On the Generic vanishing of certain Koszul cohomology groups  

CERN Document Server

We propose a new approach to study Koszul cohomology of general $g^r_d$'s on general curves via degenerations and deformations. As an application of this new method, we prove projective normality for general line bundles $L$ on general curves with $h^1(L)\\le1$ and degree greater than roughly $(5/4)g$. This improves the bound in a classical theorem of Green and Lazarsfeld. Also we give some partial results on vanishing of higher syzygies for line bundles with $h^1(L)=1$.

2011-01-01

436

Malnutrition, Gut-Microbial Interactions and Mucosal Immunity to Vaccines, 07 Nov 2011 - 11 Nov 2011, Le Meridien New Delhi, New Delhi, India - SciDe  

Wastenet

... A better understanding of the links between nutrients, the gut microbiome and the intestinal immune system is likely to pave the way to the development of innovative approaches that target activation of specific immunological pathways for promoting the hostrsquo;s gut defense. Such knowledge should positively impact on the development of vaccine formulations and intervention strategies for improved control of enteric infections in developing countries. Registration fees # The Registration Fee is $715.00 on and before September 7, 2011. # After September 7, 2011, the ...

437

Le LHC, un projet mondial  

CERN Multimedia

Since the mid-1980s the number of scientists from all over the world using CERN's facilities has increased enormously. Currently more than 6,000 users, over half of the planet's high-energy physicists, carry out fundamental research at CERN. This user community is living proof that CERN welcomes inter- regional collaboration which benefits all and boosts the progress of science. The LHC, the only machine capable of addressing problems way beyond today's frontiers of high energy physics, offers an unique opportunity for extending world wide collaboration.

1994-01-01

438

Interest of a two-dimensional matrix of detectors for the quality control of beams in static or dynamic mode; Interet d'une matrice bidimensionnelle de detecteurs pour le controle de qualite des faisceaux en mode statique ou dynamique  

Energy Technology Data Exchange (ETDEWEB)

A 2D matrix allows a fairly rapid verification of irradiation parameters transferred on computer processing equipment without expanding the dosimetry means to implement. Associated to 'Multicheck and Verisoft' software it will handle some of the regulatory recommendations of the A.F.S.S.A.P.S. for quality control of accelerators and ensure the traceability of testing carried out. (N.C.)

2007-11-15

439

Gunshot wounds of abdomen detected at CT. Personal experience in 30 patients; Ferite da arma da fuoco dell'addome studiate con tomografia computerizzata: esperienza personale in 30 casi  

Energy Technology Data Exchange (ETDEWEB)

The paper investigates the yield and the role of the computerized tomography in diagnosing abdominal gunshot wounds, with their rich and varied radiological signs and associated injuries, and subsequently used in the diagnosis. [Italian] Scopo del lavoro e' riportare l'esperienza personale nell'uso della tomografia computerizzata per riconoscere le lesioni da arma da fuoco dell'addome e nelle fasi successive dell'approfondimento diagnostico.

1999-09-01

440

Development of time-resolved laser fluorescence spectrometry for on-line uranium checking in solutions of the Purex reprocessing process; Developpement de la spectrofluorimetrie laser a resolution temporelle pour le controle en ligne de l`uranium dans les solutions du procede de retraitement purex  

Energy Technology Data Exchange (ETDEWEB)

The Purex process and the fluorescence spectrometry are first recalled, then uranyl fluorescence is studied in a pure nitric medium without other elements to establish a theoretical model, allowing the description of uranium fluorescence signal with a general equation. The influence of different parameters (temperature, inhibitors, dynamic quenching of iron and cerium) is investigated to develop the model. A quantitative analysis method without addition of reagents is proposed to validate the model.

1992-02-25

441

Description of modelling to be implemented in the fuel rod thermomechanics code Cyrano3; Description des modeles a introduire dans le logiciel de thermomecanique du crayon combustible Cyrano3  

Energy Technology Data Exchange (ETDEWEB)

CYRANO3 is the new EDF thermomechanical code developed to evaluate the overall fuel rod behavior under irradiation. In that context, this paper presents the phenomena to be simulated and the correlations adopted for modelling purposes. The empirical models presented are taken from the CYRANO2 code and a compilation of the relevant literature. The present revision corrects and supplements version B on the basis of its use during the software coding phase from January 1991 to May 1993. (authors). figs., tabs., 120 refs.

1993-06-01

442

Cosmic no-hair theorem in power-law inflation  

Energy Technology Data Exchange (ETDEWEB)

We prove a cosmic no-hair theorem for Bianchi models in power-law inflation. Provided that the potential of an inflaton {phi} is exp({minus}{lambda}{kappa}{phi}) with 0{le}{lambda}{lt} {radical}2/3 , we find that the isotropic power-law solution is the unique attractor for any initially expanding Bianchi-type models except type IX. For Bianchi type IX, this conclusion is also true if the initial ratio of the vacuum energy to the maximum three-curvature is larger than one half.

1992-02-15

443

Bone geometry, biomechanics, and mineral content of the distal radius in uremic patients with severe hyperparathyroidism; Valutazione delle proprieta' geometriche, biomeccaniche e osteodensitometriche del radio ultradistale mediante tomografia computerizzata quantitativa periferica nei pazienti uremici affetti da iperparatiroidismo grave  

Energy Technology Data Exchange (ETDEWEB)

Bone integrity and mineral status were studied with a noninvasive method in uremic patients with severe secondary hyperparathyroidism undergoing maintenance hemodialysis. [Italian] Gli autori propongono un metodo non invasivo per studiare la densita' minerale e le caratteristiche geometriche e biomeccaniche dell'osso nei pazienti uremici affetti da iperparatiroidismo secondario grave.

1999-04-01

444

Negotiating equity for management of DOE wastes  

Energy Technology Data Exchange (ETDEWEB)

One important factor frustrating optimal management of Department of Energy (DOE)-complex wastes is the inability to use licensed and permitted facilities systematically. Achieving the goal of optimal use of DOE`s waste management facilities is politically problematic for two reasons. First, no locale wants to bear a disproportionate burden from DOE wastes. Second, the burden imposed by additional wastes transported from one site to another is difficult to characterize. To develop a viable framework for equitably distributing these burdens while achieving efficient use of all DOE waste management facilities, several implementation and equity issues must be addressed and resolved. This paper discusses stakeholder and equity issues and proposes a framework for joint research and action that could facilitate equity negotiations among stakeholder and move toward a more optimal use of ...

1994-09-01

445

Low-level Waste Forum meeting report. Winter meeting, January 26--28, 1994  

Energy Technology Data Exchange (ETDEWEB)

The Low-Level Radioactive Waste Forum is an association of representatives of states and compacts established to facilitate state and compact commission implementation of the Low-Level Radioactive Waste Policy Act of 1980 and the Low-Level Radioactive Waste Policy Amendments Act of 1985 and to promote the objectives of low-level radioactive waste regional compacts. The Forum provides an opportunity for states and compacts to share information with one another and to exchange views with officials of federal agencies. The Forum participants include representatives from regional compacts, designated host states, unaffiliated states, and states with currently-operating low-level radioactive waste facilities. This report contains information synthesizing the accomplishments of the Forum, as well as any new advances that have been made in the management of low-level radioactive ...

1994-12-31

446

Liquid radioactive waste discharges from B plant to cribs  

Energy Technology Data Exchange (ETDEWEB)

This engineering report compiles information on types and quantities of liquid waste discharged from B-Plant directly to cribs, ditches, reverse wells, etc., that are associated with B-Plant. Waste discharges to these cribs via overflow form 241-B, 241-BX, and 241-BY tank farms, and waste discharged to these cribs from sources other than B-Plant are discussed.Discharges from B-Plant to other cribs, unplanned releases, or waste remaining in tanks are not included in the report. Waste stream composition information is used to predict quantities of individual chemicals sent to cribs. This provides an accurate mass balance of waste streams from B-Plant to these cribs. These predictions are compared with known crib inventories as a verification of the process.

1996-05-29

447

Carbon monoxide - hydrogen combustion characteristics in severe accident containment conditions. Final report  

International Nuclear Information System (INIS)

Carbon monoxide can be produced in severe accidents from interaction of ex-vessel molten core with concrete. Depending on the particular core-melt scenario, the type of concrete and geometric factors affecting the interaction, the quantities of carbon monoxide produced can vary widely, up to several volume percent in the containment. Carbon monoxide is a combustible gas. The carbon monoxide thus produced is in addition to the hydrogen produced by metal-water reactions and by radiolysis, and represents a possibly significant contribution to the combustible gas inventory in the containment. Assessment of possible accident loads to containment thus requires knowledge of the combustion properties of both CO and H_2 in the containment atmosphere. Extensive studies have been carried out and are still continuing in the nuclear industry to assess the threat of hydrogen in a severe reactor accident. However the contribution of carbon monoxide to the combustion threat has received less ...

1994-10-19

448

Challenges for Lithuania: Ignalina NPP Early Closure  

International Nuclear Information System (INIS)

As a condition of accession into the European Union (EU), Lithuania is committed to the closure and decommissioning of Ignalina NPP comprising two RBMK-1500 reactor units (Fig. 1). It was agreed in a special protocol to the Accession Treaty that, in return for adequate EU financial assistance, Unit 1 would be closed before 2005 and Unit 2 by the end of 2009. The first unit was duly shut down on December 31, 2004. Lithuania, which has borders with Russia (Kaliningrad territory), Poland, Latvia and Belarus, spent fifty years as part of the Soviet Union and was deeply integrated into its economy and electrical infrastructure. At the break-up of the USSR, Lithuania inherited electricity generating capacity designed to supply the north-west region including ownership of Ignalina NPP located in the north-east of the country. Ignalina NPP Unit 1 was commissioned in 1983, Unit 2 in 1987; the planned lifespan of each unit was 30 years. Construction of a third unit was ...

2008-01-01

449

Case studies: Experience in China [Factors affecting public and political acceptance for the implementation of geological disposal  

International Nuclear Information System (INIS)

China operates 10 nuclear power reactors and has 5 more under construction. A large extension of nuclear power is expected by 2020. Nuclear generated electricity accounts for 2% of the total electric power generation. The Chinese policy is to have spent fuel reprocessed in China. So, final disposal include vitrified waste and some CANDU spent fuel for direct disposal. There is a legal framework in place in China to manage HLW. The China Atomic Energy Authority (CAEA) has the responsibility for setting policy on HLW disposal and implementing the disposal programme, while the National Nuclear Safety Administration (NNSA) and the State Environment Protection Agency (SEPA) are the regulatory bodies, which are responsible for licensing and reviewing of environment impact assessment report. The China National Nuclear Corporation (CNNC) is considered to be the actual implementer, conducting the major activities for HLW management. In the 1980's, China started generic ...

2007-10-01

450

Theory and evidence of economies of scale in the development of waste management systems  

Energy Technology Data Exchange (ETDEWEB)

Waste is a cost of doing business. This cost can be considered in terms of the potential adverse health and environmental impacts, or the waste management costs associated with avoiding, minimizing, and controlling those impacts. There is an anticipated increase in the cost of waste management as a result of the increasing requirements for regulatory compliance. To meet the total waste management capacity needs of the organization and the compliance requirements, low-level radioactive, hazardous, and mixed waste management will need demonstrated technologies strategically managed as a technology portfolio. The role of the decision maker is to select the optimum mix of technologies and facilities to provide the waste management capacity needed for the next twenty years. The waste management system resulting from this mix includes multiple ...

1989-01-01

451

The control of radioactive wastes and the quality assurance requirements  

International Nuclear Information System (INIS)

For prolonged storage and eventual disposal radioactive wastes will be solidified to reduce the problems which accompany liquid waste whilst solid wastes will be encapsulated in an immobilising matrix. In the solidification and encapsulation process it will be important to produce a material in a form which is chemically stable, mechanically strong and which will not react with or allow free passage of groundwater. To this end a continuous check will be required to ensure that the various wastes are chemically compatible with the solidifying and binding matrices and that the associated processes are performed against a strict Quality Programme. The Quality Programme will be extensive requiring the specification of procedures for assessing the quality and nature of the wastes, the detailed operation of the solidification and/or encapsulation, the overpack requirements for ...

452

The Los Alamos National Laboratory Transuranic Waste Retireval Project  

Energy Technology Data Exchange (ETDEWEB)

This paper presents the status of the Los Alamos National Laboratory (LANL) project for remediation of transuranic (TRU) and TRU mixed waste from Pads 1, 2, and 4. Some of the TRU waste packages retrieved from Pad I are anticipated to be part of LANL`s initial inventory to be shipped to the Waste Isolation Pilot Plant (WIPP) in April 1998. The TRU Waste Inspectable Storage Project (TWISP) was initiated in February 1993 in response to the New Mexico Environment Department`s (NMED`s) Consent Agreement for Compliance Order, ``New Mexico Hazardous Waste Agreement (NMHWA) 93-03.`` The TWISP involves the recovery of approximately 16,865 TRU and TRU-mixed waste containers currently under earthen cover on Pads 1, 2, and 4 at Technical Area 54, Area G, and placement of that waste into inspectable storage. All waste will be moved ...

1997-02-01

453

Nuclear waste treatment program: Annual report for FY 1987  

Energy Technology Data Exchange (ETDEWEB)

Two of the US Department of Energy's (DOE) nuclear waste management-related goals are to ensure that waste management is not an obstacle to the further development of light-water reactors and the closure of the nuclear fuel cycle and to fulfill its institutional responsibility for providing safe storage and disposal of existing and future nuclear wastes. As part of its approach to achieving these goals, the Office of Remedial Action and Waste Technology of DOE established what is now called the Nuclear Waste Treatment Program (NWTP) at the Pacific Northwest Laboratory during the second half of FY 1982. To support DOE's attainment of its goals, the NWTP is to provide technology necessary for the design and operation of nuclear waste treatment facilities by commercial enterprises as part of a licensed waste management system ...

1988-09-01

454

Influence of temperature on strength of cemented surrogate nitrate salt waste  

Energy Technology Data Exchange (ETDEWEB)

The Rocky Flats Plant (RFP) generates large volumes of a low level aqueous waste stream high in nitrate salts. The aqueous waste is concentrated by evaporation and then mixed with Portland cement prior to transport and disposal. Planned process upgrades include a new horizontal thin film evaporator. Temperature of brine at discharge end of the new evaporator will be near boiling point. Introduction of hot water to cement can degrade the monolithic waste form. However, the RFP salt waste contains high concentrations of compounds known to retard hydration. This paper discusses impact of introducing high temperature waste to cement. The study evaluated three waste compositions: (1) highest probable nitrate composition, (2) highest probable chloride composition, and (3) current composition. Results showed that compressive strength of final waste ...

1993-01-01

455

Influence of temperature on strength of cemented surrogate nitrate salt waste  

Energy Technology Data Exchange (ETDEWEB)

The Rocky Flats Plant (RFP) generates large volumes of a low level aqueous waste stream high in nitrate salts. The aqueous waste is concentrated by evaporation and then mixed with Portland cement prior to transport and disposal. Planned process upgrades include a new horizontal thin film evaporator. Temperature of brine at discharge end of the new evaporator will be near boiling point. Introduction of hot water to cement can degrade the monolithic waste form. However, the RFP salt waste contains high concentrations of compounds known to retard hydration. This paper discusses impact of introducing high temperature waste to cement. The study evaluated three waste compositions: (1) highest probable nitrate composition, (2) highest probable chloride composition, and (3) current composition. Results showed that compressive strength of final waste ...

1993-03-01

456

DWPF waste form compliance plan (Draft Revision)  

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy currently has over 100 million liters of high-level radioactive waste in storage at the Savannah River Site (SRS). In the late 1970's, the Department of Energy recognized that there were significant safety and cost advantages associated with immobilizing the high-level waste in a stable solid form. Several alternative waste forms were evaluated in terms of product quality and reliability of fabrication. This evaluation led to a decision to build the Defense Waste Processing Facility (DWPF) at SRS to convert the easily dispersed liquid waste to borosilicate glass. In accordance with the NEPA (National Environmental Policy Act) process, an Environmental Impact Statement was prepared for the facility, as well as an Environmental Assessment of the alternative waste forms, and issuance of a Record of Decision (in December, 1982) on ...

1991-01-01

457

DWPF waste form compliance plan (Draft Revision)  

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy currently has over 100 million liters of high-level radioactive waste in storage at the Savannah River Site (SRS). In the late 1970`s, the Department of Energy recognized that there were significant safety and cost advantages associated with immobilizing the high-level waste in a stable solid form. Several alternative waste forms were evaluated in terms of product quality and reliability of fabrication. This evaluation led to a decision to build the Defense Waste Processing Facility (DWPF) at SRS to convert the easily dispersed liquid waste to borosilicate glass. In accordance with the NEPA (National Environmental Policy Act) process, an Environmental Impact Statement was prepared for the facility, as well as an Environmental Assessment of the alternative waste forms, and issuance of a Record of Decision (in December, 1982) on the ...

1991-12-31

458

Analysis of options for coal combustion waste management in the Pacific Basin  

Energy Technology Data Exchange (ETDEWEB)

Many Pacific Basin countries rely on oil for electricity production. Alternative fuel sources such as coal, which is available in the Pacific Basin, can help mitigate adverse impacts of sudden price increases or supply disruptions. Coal combustion produces solid and potentially hazardous wastes of concern to environmental regulators and utility managers. This paper identifies issues associated with managing coal combustion wastes in the Pacific Basin, using the state of Hawaii as a case study. Hawaii is typical of many Pacific Basin locations in that it depends on oil, has limited sites, for waste management operations, and is subject to domestic and international waste management regulations. The paper discusses coal-fired utility wastes, environmental impacts of coal combustion waste disposal, and regulatory requirements that impact coal ...

1993-10-01

459

Yucca Mountain, Nevada - A Proposed Geologic Repository for High-Level Radioactive Waste (Volume 1) Introduction  

Energy Technology Data Exchange (ETDEWEB)

Yucca Mountain in Nevada represents the proposed solution to what has been a lengthy national effort to dispose of high-level radioactive waste, waste which must be isolated from the biosphere for tens of thousands of years. This chapter reviews the background of that national effort and includes some discussion of international work in order to provide a more complete framework for the problem of waste disposal. Other chapters provide the regional geologic setting, the geology of the Yucca Mountain site, the tectonics, and climate (past, present, and future). These last two chapters are integral to prediction of long-term waste isolation.

2006-09-25

460

Waste plastic treatment equipment; Hai plastic shori sochi  

Energy Technology Data Exchange (ETDEWEB)

In recent years, there has been increasing demand for resource-recycling of waste plastic, especially due to the introduction of legislation on recycling of materials used for packages of household goods. Methods of recycling waste plastic from household goods are currently still under development, and appropriate techniques to deal with such waste are required. Toshiba has developed a technique to dehydrochlorinate plastic containing polyvinyl chloride (PVC). This paper introduces our petrolization and dehydrochlorination system for waste plastic containing PVC. (author)

1999-04-01

461

Waste management systems model for energy systems sites on the Oak Ridge Reservation  

Energy Technology Data Exchange (ETDEWEB)

There is a model on the Oak Ridge Reservation which provides requirements for determining capacities and capabilities related to low-level, hazardous, and mixed wastes. In FY 1987, the model will be sufficiently advanced to provide various waste management scenarios. These scenarios will be compared technically, operationally, and financially by use of waste characterization data and process simulators that are currently under development. The results of the process simulations will be used to help identify waste treatment, storage, and disposal technologies that need to be demonstrated prior to full-scale development for DOE use. The information derived from this effort will be made available to all DOE facilities.

1986-01-01

462

Vitrification of waste  

Energy Technology Data Exchange (ETDEWEB)

A method for encapsulating and immobilizing waste for disposal. Waste, preferably, biologically, chemically and radioactively hazardous, and especially electronic wastes, such as circuit boards, are placed in a crucible and heated by microwaves to a temperature in the range of approximately 300{degrees}C to 800{degrees}C to incinerate organic materials, then heated further to a temperature in the range of approximately 1100{degrees}C to 1400{degrees}C at which temperature glass formers present in the waste will cause it to vitrify. Glass formers, such as borosilicate glass, quartz or fiberglass can be added at the start of the process to increase the silicate concentration sufficiently for vitrification.

1992-12-31

463

Quality assurance requirements for certification of TRU waste for shipment to the WIPP  

International Nuclear Information System (INIS)

This document presents the basic Quality Assurance (QA) requirements which shall be included in the Quality Assurance Program established by sites planning to certify Transuranic (TRU) Waste to Waste Isolation Pilot Plant (WIPP) Waste Acceptance Criteria. These QA requirements were modeled after ANSI/ASME NQA-1-1979. The application of quality assurance to Waste Certification Programs is required by WIPP-DOE-069 and DOE Order 5700.6A, as implemented by DOE Order AL 5700.6A.

464

Projected radionuclide inventories of DWPF glass from current waste at time of production. Revision 1  

Energy Technology Data Exchange (ETDEWEB)

The Waste Acceptance Preliminary Specifications (WAPS) require that the DWPF estimate the inventory of long-lived radionuclides present in the waste glass, and report the values in the Waste Form Qualification Report. In this report, conservative (biased high) estimates of the radionuclide inventory of glass produced from waste currently in the Tank Farm are provided. In most cases, these calculated values compare favorably with actual data. In those cases where the agreement is not good, the values reported here are conservative.

1993-02-04

465

Process and system for treatment of radioactive waste  

Energy Technology Data Exchange (ETDEWEB)

In a treatment system of radioactive waste solution including sodium sulfate generated from a boiling water type nuclear reactor, waste solution is fed into a thin film evaporator where the waste solution is evaporated and made into powder while precipitating in a peripheral surface of the evaporator vessel. The surface of the precipitated solid is wiped by rotating wiper blades and removed off as radioactive solid powder. The rotational speed of a rotor to which the wiper blades are secured is controlled at a minimum and necessary rotational speed which contributes to make the waste solution into the powder so that the rate of worn out of the wiper blade is decreased.

1985-07-02

466

PFP dangerous waste training plan  

Science.gov (United States)

This document establishes the minimum training requirements for the Plutonium Finishing Plant (PFP) personnel who are responsible for management of dangerous waste. The training plan outlines training requirements for handling of solid dangerous waste during generator accumulation and liquid dangerous waste during treatment and storage operations. The implementation of this training plan will ensure the PFP facility compliance with the training plan requirements of Dangerous Waste Regulation. Chapter 173-303-330. Washington Administrative Code (WAC). The requirements for such compliance is described in Section 11.0 of WHC-CM-7-5 Environmental Compliance Manual.

1996-01-01

467

Material-not-categorized-as-waste survey for 1992  

Energy Technology Data Exchange (ETDEWEB)

In October 1992, the US Department of Energy, Richland Field Office (RL) requested that Westinghouse Hanford Company (WHC) respond to a letter from EM-331 asking for completion of a survey of items in storage but not categorized as waste (Roberts 1992). The letter contained an attachment with instructions on how to fill out the attached form and what to exclude from the survey (Appendix A). This report is a summary of the information from the response issued to RL. This report primarily is for use in estimating future waste volumes that may have been overlooked because of the nature of their classification as material not categorized as waste (MNCAW) (i.e., not yet declared Waste).

1993-07-01

468

Mastery of risks: we build the memory of radioactive waste disposal facilities  

International Nuclear Information System (INIS)

The ANDRA, the French national agency of radioactive wastes, is organizing today the information needs of tomorrow. The aim is to allow the future generations to have access to the knowledge of the existence of subsurface radioactive waste facilities and to understand the context and technologies of such facilities. The storage of this information is made on 'permanent paper', a high resistant paper with a lifetime of 600 to 1000 years. An updating of these data is made every 5 years for each waste disposal center. Another project, still in progress, concerns the memory management of deep geologic waste disposal facilities for which the time scale to be considered is of the order of millennia. (J.S.)

469

Feasibility study on the management of the disposal of Bangkok municipal waste. Final report  

Energy Technology Data Exchange (ETDEWEB)

In January, 1985, the Government of Thailand sought assistance from the United States Trade and Development Program (USTDP) to undertake a feasibility study to review and update the solid waste management master plan, with particular emphasis to be placed on waste disposal methods. In April, 1985, the USTDP engaged the firm of Engineering and Economic Research, Inc. to carry out a definitional/prefeasibility study to assess the potential of a project for solid waste management and energy production using municipal solid waste as fuel.

1989-09-01

470

Co-processing; Waste-derived fuels help solve compliance problems and produce usable materials  

Energy Technology Data Exchange (ETDEWEB)

An estimated 265 million tons of hazardous waste are generated annually in the United States. Traditional waste disposal methods are inadequate, and many are no longer environmentally acceptable. Still, the waste increases along with demands for clean, environmentally safe methods for dealing with it. Faced with these demands, many hazardous waste generators are turning for help to co-processing,'' technology that goes beyond a no-impact solution to one of net positive impact, both environmentally and economically. This paper describes co-processing.

1990-01-01

471

Aqueous radioactive waste bituminization  

International Nuclear Information System (INIS)

The bituminzation of decontamination and ion exchange resin stripping wastes with four grades of asphalt was investigated to determine the effects of asphalt type on the properties of the final products. All waste forms deformed readily under light loads indicating they would flow if not restrained. It was observed in all cases that product leaching rates increased as the hardness of the asphalt used to treat the waste increased. If bituminization is adopted for any Ontario Hydro aqueous radioactive wastes they should be treated with soft asphalt to obtain optimum leaching resistance and mechanical stability during interim storage should be provided by a corrosion resistant container.

5049-01-01

472

Anaerobic digestion of municipal solid waste: Technical developments  

Energy Technology Data Exchange (ETDEWEB)

The anaerobic biogasification of organic wastes generates two useful products: a medium-Btu fuel gas and a compost-quality organic residue. Although commercial-scale digestion systems are used to treat municipal sewage wastes, the disposal of solid organic wastes, including municipal solid wastes (MSW), requires a more cost-efficient process. Modern biogasification systems employ high-rate, high-solids fermentation methods to improve process efficiency and reduce capital costs. The design criteria and development stages are discussed. These systems are also compared with conventional low-solids fermentation technology.

1996-01-01

473

CT in the study of thoracic-pulmonary complications after liver transplantation; La Tomografia Computerizzata nello studio delle complicanze toraco-polmonari dopo trapianto del fegato  

Energy Technology Data Exchange (ETDEWEB)

In this article is reviewed the role of Computed Tomography (CT) in thoracic complications following ortho topic liver transplantation (OLT). In a post-OLT population of 567 patients transplanted in the Italian institutions, 100 patients (17.6%) were examined with chest CT. It was reviewed data relative to the total number of examinations, clinical and/or radiographic indications, the CT technique-i.e., conventional (with (out) intravenous, i.v., contrast material) or high-resolution (HRCT). It also reviewed the radiologic patterns and their correlation with the other clinical, bronchoscopic and/or laboratory results. Of 152 chest CT examinations, 45 (29.6%) were performed because of clinical indications, 31 (20.4%) because of a radiographic abnormality, 64 (42.1%) because of clinical and radiographic abnormality, 64 (42.1%) because of clinical and radiographic indications, while in 12 cases (7.9%) the reasons were unknown; 133/152 (87.5%) examinations had been performed with ...

2000-12-01

474

Browse Conditions - Genetics Home Reference  

Science.gov (United States)

Home A service of the U.S. National Library of Medicine® Home Conditions Genes Chromosomes Handbook Glossary Resources Genetic Conditions > Browse Conditions 1-9 | A | B | C...

2011-09-24

475

Contamination by depleted uranium (Du) in South Serbia  

Energy Technology Data Exchange (ETDEWEB)

The paper present the results of the study on D.U. (depleted uranium) contamination in the environment and possible effects on animal healths in the region o f Bujanovac. Samples of soil, feed, leaves, grass, lichen, moss, honey and water were collected randomly in 2003/2004 in the vicinity of the target area (500-1000 m) and 5 km from the target area. Activity of the radionuclides ({sup 226}Ra, {sup 232}Th, {sup 40}K, {sup 210}Pb, {sup 238}U, {sup 235}U, {sup 137}Cs, {sup 7}Be) in soils, grass, lichen, moss and honey was determined on Hp Ge detector (Canberra, relative efficiency 23%) by standard gamma spectrometry. Total alpha and beta activity in water was determined on proportional alpha/beta counter (Canberra 2400, efficiency for alpha emitters 11%, efficiency for beta emitters 30%). Non significantly higher values of concentrations of {sup 226}Ra, {sup 232}Th, {sup 238}U and {sup 235}U were measured in the immediate vicinity of the targeted site, but {sup 235}U/{sup 238}U ...

2006-07-01

476

Triggered instabilities in rocket motors and active combustion control for an incinerator afterburner  

Science.gov (United States)

Two branches of research are conducted in this thesis. The first deals with nonlinear combustion response as a mechanism for triggering combustion instabilities in solid rocket motors. A nonlinear wave equation is developed to study a wide class of combustion response functions to second-order in fluctuation amplitude. Conditions for triggering are derived from analysis of limit cycles, and regions of triggering are found in parametric space. Introduction of linear cross-coupling and quadratic self-coupling among the acoustic modes appears to be how the nonlinear combustion response produces triggering to a stable limit cycle. Regions of initial conditions corresponding to stable pulses were found, suggesting that stability depends on initial phase angle and harmonic content, as well as the composite amplitude, of the pulse. Also, dependence of nonlinear stability upon system parameters is considered. The second part of this thesis presents ...

1999-01-01

477

Dynamic behaviour of dc double anode plasma torch at atmospheric pressure  

International Nuclear Information System (INIS)

An original dc double anode plasma torch which provides a long-time and highly stable atmospheric plasma jet has been devised for the purpose of hazardous waste treatment. The arc fluctuations and dynamic behaviour of the argon and argon-nitrogen plasma jets under different operating conditions have been investigated by means of classical tools, such as the statistic method, fast Fourier transform (FFT) and correlation analysis. In our experiments, the takeover mode is identified as the fluctuation characteristic of the argon plasma jet while the restrike mode is typical in the argon-nitrogen plasma dynamic behaviour. In the case of pure argon, the FFT and correlation calculation results of electrical signals exhibit the only characteristic frequency of 150 Hz, which originates from the torch power and is independent of any change in the operating conditions. It indicates that the nature of fluctuations in an argon plasma ...

2007-07-07

478

SELECTIVE REMOVAL OF STRONTIUM AND CESIUM FROM SIMULATED WASTE SOLUTION WITH TITANATE ION EXCHANGERS IN A FILTER CARTRIDGE CONFIGURATION  

Energy Technology Data Exchange (ETDEWEB)

This report describes experimental results for the selective removal of strontium and cesium from simulated waste solutions using monosodium titanate (MST) and crystalline silicotitanate (CST)-laden filter cartridges. Four types of ion exchange cartridge media (CST and MST designed by both 3M and POROX{reg_sign}) were evaluated. In these proof-of-principle tests effective uptake of both Sr-85 and Cs-137 was observed. However, the experiments were not performed long enough to determine the saturation levels or breakthrough curve for each filter cartridge. POREX{reg_sign} MST cartridges, which by design were based on co-sintering of the active titanates with polyethylene particles, seem to perform as well as the 3M-designed MST cartridges (impregnated filter membrane design) in the uptake of strontium. At low salt simulant conditions (0.29 M Na{sup +}), the instantaneous decontamination factor (D{sub F}) for Sr-85 with the 3M-design MST cartridge ...

2011-05-26

479

The Waste Management Plan integration into Decommissioning Plan of the WWR-S research reactor from Romania  

International Nuclear Information System (INIS)

The paper presents the progress of the Radioactive Waste Management Plan which accompanies the Decommissioning Plan for research reactor WWR-S located in Magurele, Ilfov, near Bucharest, Romania. The new variant of the Decommissioning Plan was elaborated taking into account the IAEA recommendation concerning radioactive waste management. A new feasibility study for WWR-S decommissioning was also developed. The preferred safe management strategy for radioactive wastes produced by reactor decommissioning is outlined. The strategy must account for reactor decommissioning, as well as rehabilitation of the existing Radioactive Waste Treatment Plant and the upgrade of the Radioactive Waste Disposal Facility at Baita-Bihor. Furthermore, the final rehabilitation of the laboratories and reusing of cleaned reactor building is envisaged. An inventory of each type of radioactive ...

2008-05-28

480

Survey of agents and techniques applicable to the solidification of low-level radioactive wastes  

Energy Technology Data Exchange (ETDEWEB)

A review of the various solidification agents and techniques that are currently available or potentially applicable for the solidification of low-level radioactive wastes is presented. An overview of the types and quantities of low-level wastes produced is presented. Descriptions of waste form matrix materials, the wastes types for which they have been or may be applied and available information concerning relevant waste form properties and characteristics follow. Also included are descriptions of the processing techniques themselves with an emphasis on those operating parameters which impact upon waste form properties. The solidification agents considered in this survey include: hydraulic cements, thermoplastic materials, thermosetting polymers, glasses, synthetic minerals and composite materials. This survey is part of a program supported by the United States ...

1981-12-01

481

Solidification of DOE problem wastes  

Energy Technology Data Exchange (ETDEWEB)

Sodium nitrate waste has been successfully solidified in two types of polymeric materials: polyethylene, a thermoplastic material, and polyester styrene (PES), a thermosetting material. Waste form property evaluation tests such as ANS 16.1 leaching test and compressive strength measurements were performed on the waste forms containing various amounts of sodium nitrate. A single-screw extruder was employed for incorporating dry waste into polyethylene at its melt temperature of 120/sup 0/C to produce a homogenous mixture. Results of the leaching test for polyethylene waste forms containing 30, 50, 60 and 70 wt% sodium nitrate are presented as cumulative fraction leached and leaching indices ranging from 11 to 7.8. Two PES systems are discussed. The first is for solidification of dry salt wastes and the second is a water extendible system that is compatible with ...

1986-01-01

482

Recycling of waste polymeric materials using ionizing radiation techniques for possible applications and practical uses  

International Nuclear Information System (INIS)

recycling of waste polypropylene (WPP) and waste rubber (WR) originated from rejected worn-out tires present very important problem due to their huge amount and their negative impact on environment. many communities in the world are struggling with this problem of how to manage waste disposal, in order to eliminate or reduce waste rubber from the environment and to reduce costs of some rubber and polypropylene articles. trials to reuse waste rubber and waste polypropylene, have encountered some difficulties.such two substrate polymers differ from each other in nature, since waste polypropylene is thermoplastic while waste rubber exists in thermosetting state. accordingly, the study and use of their mixtures should be very interesting.the aim of this work is to modify the physical and chemical properties of WR and WPP ...

2007-01-01

483

Recycling of plastic waste in blast furnace; Koro ni okeru hai plastic riyo gijutsu  

Energy Technology Data Exchange (ETDEWEB)

Features particular to the technology of using a blast furnace for the recycling of plastic waste are reported, and the behavior of plastic waste injected into a blast furnace is described. The plastic waste is injected into the furnace borne on a 1200degC hot blast through the tuyere. The plastic is converted into a reducing gas in the furnace, and the gas on its way up in the furnace is utilized as a reducing agent in the iron ore reducing reaction. The process is described below. All kinds of plastic waste may be utilized in this fashion, with the exception of polyvinyl chloride. As for polyvinyl chloride, efforts are under way to develop a technology to recycle this plastic. The method using the blast furnace tolerates a wide range of impurities, and the plastic waste is only to be crushed and granulated before use in the furnace. Plastic waste coarsely ...

1998-05-20

484

Process development for remote-handled mixed-waste treatment  

Energy Technology Data Exchange (ETDEWEB)

The Oak Ridge National Laboratory (ORNL) is developing a treatment process for remote-handled (RH) liquid transuranic mixed waste governed by the concept of minimizing the volume of waste requiring disposal. This task is to be accomplished by decontaminating the bulk components so the process effluent can be disposed with less risk and expense. Practical processes have been demonstrated on the laboratory scale for removing cesium 137 and strontium 90 isotopes from the waste, generating a concentrated waste volume, and rendering the bulk of the waste nearly radiation free for downstream processing. The process is projected to give decontamination factors of 10{sup 4} for cesium and 10{sup 3} for strontium. Because of the extent of decontamination, downstream processing will be contact handled. The transuranic, radioactive fraction of the mixed waste stream will ...

1990-01-01

485

Nuclear waste form risk assessment for US defense waste at Savannah River Plant. Annual report fiscal year 1980  

Energy Technology Data Exchange (ETDEWEB)

Waste form dissolution studies and preliminary performance analyses were carried out to contribute a part of the data needed for the selection of a waste form for the disposal of Savannah River Plant defense waste in a deep geologic repository. The first portion of this work provides descriptions of the chemical interactions between the waste form and the geologic environment. We reviewed critically the dissolution/leaching data for borosilicate glass and SYNROC. Both chemical kinetic and thermodynamic models were developed to describe the dissolution process of these candidate waste forms so as to establish a fundamental basis for interpretation of experimental data and to provide directions for future experiments. The complementary second portion of this work is an assessment of the impacts of alternate waste forms upon the consequences of disposal in various ...

1981-07-01

486

Liquid waste evaporator operating experience  

Energy Technology Data Exchange (ETDEWEB)

Atomic Energy of Canada Limited (AECL) operates the Waste Treatment Centre (WTC) to treat and immobilize some of the low- level radioactive waste (LLRW) streams at the Chalk River Laboratories (CRL). The WTC at treats low- level radioactive liquid waste by removing the contaminants from the wastewater, concentrating them, and immobilizing them. The fundamental design concept for the WTC is to process the waste streams using forced circulation type liquid waste evaporation (LWE), to solidify the concentrates using thin film evaporator and to discharge the purified effluent into the Ottawa River following verification monitoring. The solidified product drums are stored in existing storage facilities in the CRL. The LWE was installed in the WTC to treat the LLRW. After about four (4) years of design, construction and cold commissioning, the active commissioning of the evaporator ...

2006-07-01

487

Liquid waste evaporator operating experience  

International Nuclear Information System (INIS)

Atomic Energy of Canada Limited (AECL) operates the Waste Treatment Centre (WTC) to treat and immobilize some of the low- level radioactive waste (LLRW) streams at the Chalk River Laboratories (CRL). The WTC at treats low- level radioactive liquid waste by removing the contaminants from the wastewater, concentrating them, and immobilizing them. The fundamental design concept for the WTC is to process the waste streams using forced circulation type liquid waste evaporation (LWE), to solidify the concentrates using thin film evaporator and to discharge the purified effluent into the Ottawa River following verification monitoring. The solidified product drums are stored in existing storage facilities in the CRL. The LWE was installed in the WTC to treat the LLRW. After about four (4) years of design, construction and cold commissioning, the active commissioning of the evaporator ...

2005-05-08

488

Costs for off-site disposal of nonhazardous oil field wastes: Salt caverns versus other disposal methods  

Energy Technology Data Exchange (ETDEWEB)

According to an American Petroleum Institute production waste survey reported on by P.G. Wakim in 1987 and 1988, the exploration and production segment of the US oil and gas industry generated more than 360 million barrels (bbl) of drilling wastes, more than 20 billion bbl of produced water, and nearly 12 million bbl of associated wastes in 1985. Current exploration and production activities are believed to be generating comparable quantities of these oil field wastes. Wakim estimates that 28% of drilling wastes, less than 2% of produced water, and 52% of associated wastes are disposed of in off-site commercial facilities. In recent years, interest in disposing of oil field wastes in solution-mined salt caverns has been growing. This report provides information on the availability of commercial disposal companies in oil-and gas-producing ...

1997-09-01

489

RH-TRU Waste Inventory Characterization by AK and Proposed WIPP RH-TRU Waste Characterization Objectives  

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy (DOE)-Carlsbad Field Office (CBFO) has developed draft documentation to present the proposed Waste Isolation Pilot Plant (WIPP) remote-handled (RH-) transuranic (TRU) waste characterization program to its regulators, the U.S. Environmental Protection Agency and the New Mexico Environment Department. Compliance with Title 40, Code of Federal Regulations, Parts 191 and 194; the WIPP Land Withdrawal Act (PL 102-579); and the WIPP Hazardous Waste Facility Permit, as well as the Certificates of Compliance for the 72-B and 10-160B Casks, requires that specific waste parameter limits be imposed on DOE sites disposing of TRU waste at WIPP. The DOE-CBFO must control the sites' compliance with the limits by specifying allowable characterization methods. As with the established WIPP contact handled TRU waste characterization program, ...

2002-02-26

490

Spent Fuel Transportation Package Response to the Baltimore Tunnel Fire Scenario  

International Nuclear Information System (INIS)

On July 18, 2001, a freight train carrying hazardous (non-nuclear) materials derailed and caught fire while passing through the Howard Street railroad tunnel in downtown Baltimore, Maryland. The United States Nuclear Regulatory Commission (USNRC), one of the agencies responsible for ensuring the safe transportation of radioactive materials in the United States, undertook an investigation of the train derailment and fire to determine the possible regulatory implications of this particular event for the transportation of spent nuclear fuel by railroad. Shortly after the accident occurred, the USNRC met with the National Transportation Safety Board (NTSB, the U.S. agency responsible for determining the cause of transportation accidents), to discuss the details of the accident and the ensuing fire. Following these discussions, the USNRC assembled a team of experts from the National Institute of Standards and Technology (NIST), the Center for Nuclear Waste Regulatory ...

2006-11-01

491

Waste disposal and treatment in the food processing industry. (Latest citations from the Biobusiness database). Published Search  

Energy Technology Data Exchange (ETDEWEB)

The bibliography contains citations concerning waste treatment and disposal in the food processing industry. Methods, equipment, and technology are considered. References discuss waste heat recovery and examine treatment of wastes resulting from meat and seafood processing, dairy and beverage production, and fruit and vegetable processing. The citations explore conversion of the treated waste to fertilizer and for use in animal feeds, combustion for energy production, biogas production, and composting. The recovery and recycling of usable chemicals from the food waste are also covered. Food packaging recycling is considered in a related bibliography. (Contains 250 citations and includes a subject term index and title list.)

1995-01-01

492

Status and progress in sludge washing: A pivotal pretreatment method  

Energy Technology Data Exchange (ETDEWEB)

Separation of the bulk soluble chemical salts from the insoluble metal hydroxides and radionuclides is central to the strategy of disposing Hanford tank waste. Sludge washing and caustic leaching have been selected as the primary methods for processing the 230 million L (61,000,000 gal) of Hanford tank waste. These processes are very similar to those selected for processing waste at the West Valley Site in New York and the Savannah River Site in South Carolina. The purpose of sludge washing is to dissolve and remove the soluble salts in the waste. Leaching of the insoluble solids with caustic will be used to dissolve aluminum hydroxide and chromium hydroxide, and convert insoluble bismuth phosphate to soluble phosphate. The waste will be separated into a high-level solids fraction and a liquid fraction that can be disposed of as low-level waste after cesium ...

1995-01-01

493

Radioactive waste management in the USSR: A review of unclassified sources  

Energy Technology Data Exchange (ETDEWEB)

The Soviet Union does not currently have an overall radioactive waste management program or national laws that define objectives, procedures, and standards, although such a law is being developed, according to the Soviets. Occupational health and safety does not appear to receive major attention as it does in Western nations. In addition, construction practices that would be considered marginal in Western facilities show up in Soviet nuclear power and waste management operations. The issues involved with radioactive waste management and environmental restoration are being investigated at several large Soviet institutes; however, there is little apparent interdisciplinary integration between them, or interaction with the USSR Academy of Sciences. It is expected that a consensus on technical solutions will be achieved, but it may be slow in coming, especially for final disposal of high-level radioactive ...

1991-03-01

494

Improvement on Liquid Radioactive Waste Treatment System of Nuclear Power Plant By Applying Ion Exchange Method  

International Nuclear Information System (INIS)

Liquid radioactive waste treatment method of using evaporator was widely used from Kori 1 to Uljin 3 and 4, but a liquid radioactive waste treatment equipment that uses an ion exchange method instead of an evaporator was adopted aiming to minimize amount of radioactive waste and radiation exposure. However, the same equipment was introduced and applied for the first time in Korea and had experienced difficulties in securing credibility for the equipment and handling of liquid radioactive waste with inadequate data about performance and experience in operation and maintenance. In this study, examination, application and effect analysis was performed on the optimization measure for handling liquid radioactive waste of Yonggwang Nuclear Power Unit 5 and 6(YGN 5 and 6) that applies an ion exchange method

2010-10-01