Energy Technology Data Exchange (ETDEWEB)

The Soviet Union does not currently have an overall radioactive waste management program or national laws that define objectives, procedures, and standards, although such a law is being developed, according to the Soviets. Occupational health and safety does not appear to receive major attention as it does in Western nations. In addition, construction practices that would be considered marginal in Western facilities show up in Soviet nuclear power and waste management operations. The issues involved with radioactive waste management and environmental restoration are being investigated at several large Soviet institutes; however, there is little apparent interdisciplinary integration between them, or interaction with the USSR Academy of Sciences. It is expected that a consensus on technical solutions will be achieved, but it may be slow in coming, especially for final disposal of high-level radioactive ...

Energy Technology Data Exchange (ETDEWEB)

In response to the need for a comprehensive and consistent approach to the complex issue of mixed waste management, a generalized methodology for remediation of a mixed waste site has been developed. The methodology is based on requirements set forth in the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) and the Resource Conservation and Recovery Act (RCRA) and incorporates ``lessons learned`` from process design, remediation methodologies, and remediation projects. The methodology is applied to the treatment of 32,000 drums of mixed waste sludge at the Oak Ridge K-25 Site. Process technology options are developed and evaluated, first with regard to meeting system requirements and then with regard to CERCLA performance criteria. The following process technology options are investigated: (1) no action, (2) separation of hazardous and radioactive species, (3) dewatering, (4) drying, and (5) ...

International Nuclear Information System (INIS)

In this program, contemporary solidification agents are being investigated relative to their applications to major fuel cycle and non-fuel cycle low-level waste (LLW) streams. Work is being conducted to determine the range of conditions under which these solidification agents can be applied to specific LLW streams. These studies are directed primarily towards defining operating parameters for both improved solidification of problem wastes and solidification of new LLW streams generated from advanced volume reduction technologies. Work is being conducted to measure relevant waste form properties. These data will be compiled and evaluated to demonstrate compliance with waste form performance and shallow land burial acceptance criteria and transportation requirements (both as they exist and as they are modified with time). ...

International Nuclear Information System (INIS)

The fundamental points to be considered in a waste treatment system for a country like Japan, where the final disposal method has not been decided and the wastes have to be stored in the power plants, are volume reduction of the wastes, safe storage of the wastes in the plant, and flexibility regarding the final disposal. A system has been developed that consists of a thin film evaporator for the direct solidification of the liquid waste, a pelletizer for producing hard pellets from the powdered wastes, a pellet storage unit, and a solidification unit for the final disposal. A pilot plant with waste treatment capacity of 200 kg/h was built in 1976 and has proved the system feasibility. This paper reports on pilot plant tests of the thin film evaporator and other components, tests on pellet ...

Energy Technology Data Exchange (ETDEWEB)

A review of the various solidification agents and techniques that are currently available or potentially applicable for the solidification of low-level radioactive wastes is presented. An overview of the types and quantities of low-level wastes produced is presented. Descriptions of waste form matrix materials, the wastes types for which they have been or may be applied and available information concerning relevant waste form properties and characteristics follow. Also included are descriptions of the processing techniques themselves with an emphasis on those operating parameters which impact upon waste form properties. The solidification agents considered in this survey include: hydraulic cements, thermoplastic materials, thermosetting polymers, glasses, synthetic minerals and composite materials. ...

Energy Technology Data Exchange (ETDEWEB)

A testing program has been conducted by the Westinghouse Hanford Company to confirm the baseline waste form selection for use in Waste Receiving and Processing (WRAP) Module 2A. WRAP Module 2A will provide treatment required to properly dispose of containerized contact-handled, mixed low-level waste at the US Department of Energy Hanford Site in south-central Washington State. Solidification/stabilization has been chosen as the appropriate treatment for this waste. This work is intended to test cement-based, thermosetting polymer, and thermoplastic polymer solidification media to substantiate the technology approach for WRAP Module 2A. Screening tests were performed using the major chemical constituent of each waste type to measure the gross compatibility with the immobilization media and to determine formulations for more detailed testing. ...

Energy Technology Data Exchange (ETDEWEB)

Sodium nitrate waste has been successfully solidified in two types of polymeric materials: polyethylene, a thermoplastic material, and polyester styrene (PES), a thermosetting material. Waste form property evaluation tests such as ANS 16.1 leaching test and compressive strength measurements were performed on the waste forms containing various amounts of sodium nitrate. A single-screw extruder was employed for incorporating dry waste into polyethylene at its melt temperature of 120/sup 0/C to produce a homogenous mixture. Results of the leaching test for polyethylene waste forms containing 30, 50, 60 and 70 wt% sodium nitrate are presented as cumulative fraction leached and leaching indices ranging from 11 to 7.8. Two PES systems are discussed. The first is for solidification of dry salt wastes and the second is a water extendible system that ...

Science.gov (United States)

The results of studies on: (1) development of suitable glass compositions for solidification and vitrification of high level radioactive wastes, and (2) the characteristics of these compositions, namely, leaching, mechanical properties, thermal conductivity, viscosity and homogeneity evaluation are reported. Inactive simulated purex waste was used for compositions reported herein. The data generated on leaching and other product characteristics of the selected vitrified waste products was used to evaluate the performance of corresponding experimental units and techniques with respect to their reproducibility and reliability.

International Nuclear Information System (INIS)

Purpose: To enable the solidification of liquid waste containing radioactive substance in a free shape with large volume reduction ratio without a pulverizing step by producing solute in the liquid waste as a slurry in a predetermined organic solvent and forming it into a cake by mechanical exfoliation. Method: Liquid waste containing suitably concentrated radioactive substances is supplied to a centrifugal thin film evaporator together with an organic agent having a higher boiling point than water and a non aqueous solution to evaporate the water content, the solute in the waste is produced as a slurry in the organic solvent, and removed as cake-state solute slightly residued with the organic solvent by the mechanical exfoliation such as centrifugal exfoliation or settling exfoliation from the slurry-state liquid. Accordingly, it can be increased in size as compared with the powder ...

Energy Technology Data Exchange (ETDEWEB)

This report consists of a broad overview of activities at Los Alamos National Laboratory (LANL). The following topics are discussed: The growth of the waste management group; what we do today; the mission of the waste management group; the liquid waste treatment section; the radioactive liquid waste project office; the chemical waste section; the radioactive waste section; and the technical support section.

Energy Technology Data Exchange (ETDEWEB)

The Oak Ridge National Laboratory (ORNL) is developing a treatment process for remote-handled (RH) liquid transuranic mixed waste governed by the concept of minimizing the volume of waste requiring disposal. This task is to be accomplished by decontaminating the bulk components so the process effluent can be disposed with less risk and expense. Practical processes have been demonstrated on the laboratory scale for removing cesium 137 and strontium 90 isotopes from the waste, generating a concentrated waste volume, and rendering the bulk of the waste nearly radiation free for downstream processing. The process is projected to give decontamination factors of 10{sup 4} for cesium and 10{sup 3} for strontium. Because of the extent of decontamination, downstream processing will be contact handled. The transuranic, radioactive fraction of the mixed waste stream will ...

Energy Technology Data Exchange (ETDEWEB)

An examination of chemical and radiological characteristics of RI organic liquid waste, wet oxidation by Fenton reaction and decomposition liquid waste treatment process were studied. These items will be applied to develop the equipment of wet oxidation and decomposition liquid waste treatment mixed processes for the safe treatment of RI organic liquid waste which is consisted of organic solvents such as toluene, alcohol and acetone. Two types of toluene solutions were selected as a candidate decomposition material. As for the first type, the concentration of toluene was above 20 vol percent. As for the second type, the solubility of toluene was considered. The decomposition ration by Fenton reaction was above 95 percent for both of them. From the adsorption equilibrium tests, a -Na{sup +} substituted/acid treated activated carbon and Zeocarbon mixed adsorbent was selected for the fixed adsorption ...

Indian Institute of Science Theses & Dissertations (India)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

TSS (thermal swing sublimation) method was studied which uses vaporization heat and sensible heat of LNG for solidification and separation of CO2 gas in waste gases of LNG-fired combined cycle power generation system. In experiment, the mixed gas composed of CO2, H2O and N2 was used for simulating waste gas of LNG-fired combined cycle power generation systems, and the growth behavior of ice and dry ice was studied for developing dry ice making technology under low-temperature condition. As the experimental result, the following were clarified: various crystal structures depending on cooling temperature, the effect of gas flow rate on peeling of surface precipitated solids, and solidification characteristics of H2O/CO2 mixed gas. The growth rate of precipitated solid film thickness decreased with an increase in gas flow rate, while increased with CO2 concentration. The shape of a dry ice sublimator ...

Energy Technology Data Exchange (ETDEWEB)

In the nuclear power stations of GDR the rough radioactive waste includes borat-containing evaporator bottoms and spent ion exchanger resins. For its final disposal in deep geological formations (rock salt mines) this waste has to be solidified. The experience of one year lasting operation of a steam heated thin-film evaporator (heating surface 2 m{sup 3}) for evaporator bottoms to be solidified with a solid content of 200-250 g/l are reported on. In short time such amount of water is abstracted from the rough waste that due to the borate content a hot high-viscous product passes from evaporator to waste drum and there solidifies like glass to monolith. The product quality depends on the adjustment of the flow-equilibrium in the evaporator. Boric acid is used as matrix for the radioactive residues. The residual water content of the solidified waste product was about 15-20%, the ...

Energy Technology Data Exchange (ETDEWEB)

Research at the Savannah River Technology Center aided development of a technical design basis for a Waste Treatment Plant (WTP) to pre-treat and vitrify Hanford tank waste as part of the River Protection Project (RPP). The research addresses safety concerns, process optimization, and waste form compliance. This program will provide technical data to ensure that the process functions as it was designed and minimizes costs.

Energy Technology Data Exchange (ETDEWEB)

The turbulent history of legislature concerned with the waste-management industry and the amount of material on this subject as well as the significance of the material in its own right led to the decision to publish all legal regulations on waste in one volume. It includes above all the Waste Law, Regulations on Determination of Waste, Regulations on Determination of Residual Products, Technical Instructions for Waste, Regulations for Monitoring Waste and Residual Products, Regulations on Probition from the Use of Chlorofluorohydrocarbons and Halon, Regulations on Packaging and Regulations on Sewage Sludge. The introduction explains the development and the role of the Waste Law and its applicability, goals and principles: The concept of waste, avoidance of waste, avoidance of ...

Energy Technology Data Exchange (ETDEWEB)

Abstract: The Hanford Tanks Initiative (HTI) is a five-year project resulting from the technical and financial partnership of the U.S. Department of Energy`s Office of Waste Management (EM-30) and Office of Science and Technology Development (EM-50). The HTI project accelerates activities to gain key technical, cost performance, and regulatory information on two high-level waste tanks. The HTI will provide a basis for design and regulatory decisions affecting the remainder of the Tank Waste Remediation System`s tank waste retrieval Program.

Energy Technology Data Exchange (ETDEWEB)

Specifically this report: 1. Compares requirements of the WAP that are pertinent from a technical viewpoint with the WIPP pre-Permit waste characterization program, 2. Presents the results of a risk analysis of the currently emplaced wastes. Expected and bounding risks from routine operations and possible accidents are evaluated; and 3. Provides conclusions and recommendations.

International Nuclear Information System (INIS)

The feasibility of immobilizing simulated radioactive slurry (SRS) by alkali-activated slag---clay minerals composite cement (AASCM) was studied under the experimental conditions. The results show that the dosage of SRS and water cement ratio (W/C) have significant effect on the flowability of the mixture of AASCM and SRS. The more dosage of SRS, the lower flowability. When cement/sand ratio is 1: 1 and W/C is 0.45, the flowability of the mixture meets the case of solidification engineering and the compressive strength of the waste forms containing 20% SRS meets the needs of GB 14569.1-93. The setting time of the mixture of AASCM and SRS is highly dependent on temperature while sorts of anions have little influence on it. The application of AASCM is suitable below 20 degree C. The leaching resistance of AASCM based waste forms is superior to that of OPC based waste forms. The control of the forms to ...

Energy Technology Data Exchange (ETDEWEB)

The anaerobic biogasification of organic wastes generates two useful products: a medium-Btu fuel gas and a compost-quality organic residue. Although commercial-scale digestion systems are used to treat municipal sewage wastes, the disposal of solid organic wastes, including municipal solid wastes (MSW), requires a more cost-efficient process. Modern biogasification systems employ high-rate, high-solids fermentation methods to improve process efficiency and reduce capital costs. The design criteria and development stages are discussed. These systems are also compared with conventional low-solids fermentation technology.

Energy Technology Data Exchange (ETDEWEB)

This report describes the development of solidification systems for sodium nitrate waste. Sodium nitrate waste was solidified in the polymers polyethylene, polyester-styrene (PES), and water-extendible polyester-styrene (WEP). Evaluations were made of the properties of waste forms containing various amounts of sodium nitrate by leaching immersion in water, measuring compressive strengths and by the EPA Extraction Procedure. Results of the leaching test are presented as cumulative fraction leached (CFL), incremental leaching rate, and average leaching indices (LI). For waste forms containing 30 to 70 wt% sodium nitrate, the CFL ranged from 9.0 x 10/sup -3/ to 7.3 x 10/sup -1/ and the LI from 11 to 7.8. After ninety days immersion in water, the compressive strengths ranged from 720 psi to 2550 psi. The nitrate releases from these samples using the EPA Extraction Procedure were below ...

Energy Technology Data Exchange (ETDEWEB)

A process and apparatus for solidifying radioactive waste liquid containing dissolved and/or suspended solids is disclosed. The process includes chemically treating for pH adjustement and precipitation of solids, concentrating solids with a thin-film evaporator to provide liquid concentrate containing about 50% solids, and drying the concentrate with heated mixing apparatus. The heated mixing apparatus includes a heated wall and working means for shearing dried concentrate from internal surfaces and subdividing dry concentrate into dry, powdery particles. The working means includes a rotor and helical means for positively advancing the concentrate and resulting dry particles from inlet to outlet of the mixing apparatus. The dry particles may also be encapsulated in a matrix material. Entrained particles in the vapor stream from the evaporator and mixer are removed in an integral particle separator and the vapor is subsequently condensed and may be recycled upstream ...

Energy Technology Data Exchange (ETDEWEB)

The Defense TRU Waste Program (DTWP) is the focal point for the Department of Energy in national planning, integration, operation, and technical development for TRU waste management. The scope of this program extends from the point of TRU waste generation through delivery to a permanent repository. The TRU program maintains a close interface with repository development to ensure program compatibility and coordination. The defense TRU program does not directly address commercial activities that generate TRU waste. Instead, it is concerned with providing alternatives to manage existing and future defense TRU wastes. The FY 87 Program Plan is consistent with the Defense TRU Waste Program goals and objectives stated in the Defense Transuranic Waste Program Strategy Document, January 1984. The roles of participants, the ...

Energy Technology Data Exchange (ETDEWEB)

An investigation of the solidification behavior was carried out on the directionally solidified single crystal superalloy CMSX 6. The relationship between structure morphology and the process parameters has been experimentally determined and illustrated in a solidification diagram. The metallographic analyses of transverse sections within the solidification interval yield the sequence of phase formation and the evolution of solid fraction. The solidification process and the corresponding structure have been discussed in detail. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Radioactive rare earth chlorides in waste LiCl-KCl molten salts have to be separated as a stable form to minimize waste volume and to achieve stable solidification. In this work, thermal behavior of rare earth chlorides (CeCl3, GdCl3, NdCl3, PrCl3) was investigated in an oxygen condition to recover rare earth oxides from a LiCl-KCl-RECl3 system. The rare earth chlorides in the LiCl-KCl molten salts were smoothly converted to an oxychloride form at a higher temperature than 650degreeC, except for CeCl3. CeCl3 was totally converted to an oxide from at a higher temperature than 450degreeC. The rare earth oxychlorides (GdOCl, NdOCl, PrOCl) were effectively converted to oxide forms at a higher temperature than 1100degreeC. It was confirmed that rare earth oxides can be recovered from a LiCl-KCl...

International Nuclear Information System (INIS)

Technical developments in the construction of high power accelerators have created new research activities on accelerator-driven transmutation technologies (ADTT) with main applications for energy production and nuclear waste transmutation. The on-going research was reported and discussed at the conference. The studies of energy production based on ADTT indicate possible important advantages compared to the present nuclear power reactors. Natural Uranium or Thorium is burned in a subcritical reactor with or without simultaneous incineration and transmutation of nuclear waste. High level radioactive wastes and weapons Plutonium constitute an environmental and proliferation problem. Studies were reported on the possibilities to use ADTT to considerably shorten the life-time and reduce the amount of long-lived radioactive waste in order to decrease the volumes needed for long-term ...

Energy Technology Data Exchange (ETDEWEB)

A couple of domestic institutions have been investigating the application of vitrification technology to treat low- and intermediate-level radioactive wastes in Korea. In the case that such investigations prove to be successful, it is expected that commercial vitrification plants will be constructed. The safety insuring on vitrification plants could not be compatible with criterion on radioactive waste management because the facilities are at high temperature and contain a variety of accommodations for the exhaust gases and residual products. Therefore, it is necessary to suggest a new strategy or modifications of criterion of radioactive waste management on considerations related with the vitrification technology. In order to ensure the safety of vitrification plants, a technical guideline or standard for design and operation of vitrification plants must be established too. A study on the safety ...

Wastenet

... News In Practice UK work Key facts & information Mass Balance Projects Resources & Library Technical Area Contacts Site Map Benchmarking solvent waste in the UK furniture manufacturing industry OrganisationBritish Furniture Manufacturers Ltd Project ReportSolvent Waste in Furniture Manufacturing Website: www.bfmenvironment.co.uk Return to list � RSWT | Website Design Quiet Storm Solutions Ltd Please consider upgrading your browser! If you can see this ...

Energy Technology Data Exchange (ETDEWEB)

Water model experiments were conducted to develop a two-stage stirring method for obtaining higher yields and a more uniform distribution of graphite particles in copper alloys. This was followed by several melts for synthesis of copper-graphite alloys in which Ti was used as a wetting agent to improve the wettability of graphite in the copper melt. In the first stage, a vortex method was employed to facilitate the addition of graphite particles into the copper melt. In the second stage, a specially designed stirrer was used for uniform particle distribution while avoiding the formation of vortex in the melt. The two-stage stirring was found to considerably improve the recovery of graphite, over those obtained with the prior practice of single-stage stirring and resulting in a more uniform particle distribution. In addition, graphite recoveries increased with increasing Ti content in the range investigated. Floatation, fluidity, and directional solidification ...

Energy Technology Data Exchange (ETDEWEB)

The Office of Environmental Management's (EM) Roadmap, U.S. Department of Energy--Office of Environmental Management Engineering & Technology Roadmap (Roadmap), defines the Department's intent to reduce the technical risk and uncertainty in its cleanup programs. The unique nature of many of the remaining facilities will require a strong and responsive engineering and technology program to improve worker and public safety, and reduce costs and environmental impacts while completing the cleanup program. The technical risks and uncertainties associated with cleanup program were identified through: (1) project risk assessments, (2) programmatic external technical reviews and technology readiness assessments, and (3) direct site input. In order to address these needs, the technical risks and uncertainties were compiled and divided into the program areas of: Waste ...

Energy Technology Data Exchange (ETDEWEB)

In the present paper a review of the Dutch RAS programme is presented. The objectives and achievements of the programme are described. Special attention is given to a recent assessment of the international status of P and T that has been made for the Dutch authorities. The major conclusion of this assessment is that P and T is an important instrument in the management of nuclear waste to achieve the technical limits (ALARA) with respect to radiotoxicity of the waste inventory as well as radiological effects of the disposal. The technology for P and T is, however, only partially available at present and recommendations for the directions of the RAS programme are given. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The association of Finnish Plastics Industry examined the possibilities to utilize energy content of plastic wastes in spring 1990. A bark fuelled boiler plant of forest industry was used as test power plant. The power of the plant was 60 Mw. This report discusses shortly the theory of combustion of plastics. About 130 000-15 000 tons of plastic waste, corresponding to 7 % of the solid municipal waste, is dumped annually in Finland. Utilization of the plastic waste recovered from municipal wastes for energy production is technically viable in present power plants among present energy production. The chipping and mixing of the plastic in the other fuel are the only pretreatment required for the plastic waste. In Finland there are several power plants using suitable fuels for plastic mixture combustion. The portion of the plastic of the total ...

International Nuclear Information System (INIS)

Full text: Dissolution test (DT) is one of the important specifications of PFBR MOX fuel. It is a macro homogeneity test used to ascertain that the dissolution of spent fuel will be easier during reprocessing. The DT specification limit for PFBR MOX fuel is ? 1.0 wt.% residue of the whole pellet when it is dissolved in HNO3 under reflux conditions. For this test, sintered MOX pellet is dissolved in reflux condition in 60 ml of 12M HNO3 for 10 hours. This test is carried out for each batch and during complete MOX campaign a lot of MOX waste in liquid form is being generated. This liquid waste is in clean form and U and Pu is required to be recovered from the clean waste. Different methods like direct denitration, precipitation and solvent extraction are available but either the product is not of good quality for pelletization or secondary liquid wastes are generated. Microwave denitration is a faster and ...

International Nuclear Information System (INIS)

To reduce the volume of radioactive wastes after evaporation, activity carriers can be separated from the inactive salt load. Boric acid separation from PWR concentrates was considered a preliminary stage for nuclide precipitation. In connection with the precipitation process, the reaction conditions for boric acid separation were determined by bench-scale experiments. After evaluating the known purification processes, crystallization was suggested as a practicable method. After inactive bench-scale experiments, mixed crystal formation with iron hexacyanoferrate for Cs removal was chosen. The disturbing effect of the complexing agents was neutralized by a pre-dose of iron-III-salts. By specifying the precipitation conditions, for Cs-134 an activity separation from 3,0 E + 06 Bg/l to 1,9 E + 02 Bg/l, and for Cs-137 from 5,9 E + 06 Bg/l to 1,2 E + 02 Bg/l was achieved. Accordingly, the decontamination factor for Cs-134 was 16000, and for Cs-137 48000. For the ...

Energy Technology Data Exchange (ETDEWEB)

The average American generates four pounds of solid waste per day, yet increasing constraints are being placed on the ability of municipalities to handle waste disposal. Most cities face a scarcity of acceptable landfill sites and conventional incineration and landfill methods have come under strict air, water and soil pollution standards. City administrators are being encouraged to select from a variety of proposed technologies that supplant traditional waste disposal methods, some of which offer the promise of revenues from energy and resource recovery. The problem is to select from available near-term technologies those systems that will fit into a city's long-term solid-waste management program. Broadly, waste-to-energy recovery systems now available to cities may be classified as combustion, pyrolysis, biodegradation, and mechanical front-end systems. It is important ...

British Library Electronic Table of Contents (United Kingdom)

The grain morphology developed during solidification of an Al-4.5% Cu alloy is represented generally by columnar or equiaxed dendrites. Twinned feathery grains are found in the structure formed under certain heat and flow conditions during solidification. In this work, these conditions were achieved during solidification in a cavity under forced flow. Feathery grain formation is studied by means of fluid dynamics simulations with solidification included and by experiments. In order to determine the crystallographic orientation of feathery grains, electron backscattered diffraction measurements were performed. The growth features of feathery grains were analyzed by observations made normal and parallel to the growth direction. Some correlations between twinned feathery morphology, flow and ...

Energy Technology Data Exchange (ETDEWEB)

The important use of nuclear energy in Europe, and in particular in France, has a beneficial impact on the air quality but raises important problems of radioactive waste management. The technical problems encountered by the French government with the dismantling of Superphenix reactor are a good example. Moreover, despite its reassuring talks, the electronuclear industry lobby, particularly powerful, has never been able to propose any satisfactory solution for the elimination of radioactive wastes. This article makes a criticism of the lack of visibility and democratic debate in France about the sensible subject of nuclear waste management. A comparison with the situation in other countries is made. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

The primary objective of this task was to perform a variability study of the high activity waste (HAW) acidic feed to determine the impact of feed variability on the quality of the final grout and on the mixability of the salt solution into the dry powders. The HAW acidic feeds were processed through the neutralization/pH process, targeting a final pH of 12. These fluids were then blended with the dry materials to make the final waste forms. A secondary objective was to determine if elemental substitution for cost prohibitive or toxic elements in the simulant affects the mixing response, thus providing a more economical simulant for use in full scale tests. Though not an objective, the HAW simulant used in the full scale tests was also tested and compared to the results from this task. A statistically designed test matrix was developed based on the maximum molarity inputs used to make the acidic solutions. The maximum molarity inputs were: 7.39 ...

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy`s program for disposing of nuclear High-Level Waste (HLW) and transuranic (TRU) waste has been impeded by overwhelming political opposition fueled by public perceptions of actual risk. Analysis of these perceptions shows them to be deeply rooted in images of fear and dread that have been present since the discovery of radioactivity. The development and use of nuclear weapons linked these images to reality and the mishandling of radioactive waste from the nations military weapons facilities has contributed toward creating a state of distrust that cannot be erased quickly or easily. In addition, the analysis indicates that even the highly educated technical community is not well informed on the latest technology involved with nuclear HLW and TRU waste disposal. It is not surprising then, that the general public feels uncomfortable with DOE`s management plans ...

Energy Technology Data Exchange (ETDEWEB)

These Appendices describe various technologies that may be applicable to the Mixed Waste Treatment Plant (MWTP) Chemical/Physical Treatment System (CPTS). These technologies were identified by the CPTS Technical Support Group (TSG) as potentially applicable to a variety of separation, volume reduction, and decontamination requirements. The purpose was to identify all available and developing technologies, and their characteristics, for subsequent evaluation for specific requirements identified for the CPTS. However, the technologies described herein are not necessarily all inclusive, nor are they necessarily all applicable.

Energy Technology Data Exchange (ETDEWEB)

The Buried Waste Integrated Demonstration (BWID) is a program of the Department of Energy (DOE) Office of Technology Development whose mission is to evaluate different new and existing technologies and determine how well they address DOE community waste remediation problems. Twenty-three Technical Task Plans (TTPs) have been identified to support this mission during FY-92; 10 of these have identified some support requirements when demonstrations take place. Section 1 of this report describes the tasks supported by BWID, determines if a technical demonstration is proposed, and if so, identifies the support requirements requested by the TTP Principal Investigators. Section 2 of this report is an evaluation identifying facility characteristics of existing Idaho National Engineering Laboratory (INEL) facilities that may be considered for use in BWID technology demonstration activities.

International Nuclear Information System (INIS)

This feature articles described a concept and technical problems of geological disposal of high-level radioactive waste in the civil engineering. It consists of six papers such as the present statues and subjects of geological disposal by KITAYAMA Kazumi, the diastrophism, igneous activity, and upheaval and erosion by YAMAZAKI Haruo, the groundwater flow and evaluation of nuclear transfer by IJIRI Yuji, evaluation of alteration of cement materials in the ultra-long period by HAGA Kazuko, The Mizunami Underground Research Laboratory in course of construction by SAKAMAKI Masanori, and interview of the ninetieth president of JSCE (Japan Society of Civil Engineers), he places his hope on JSCE and civil engineers by KISHI Kiyoshi. (S.Y.)

Science.gov (United States)

About every 12 years, asphalt roads must be reworked, and this is usually done by placing thick layers (hot-mix overlays) of new material on top of failed material, resulting in considerable waste of material and use of new asphalt binder. A good recycling agent is needed, not only to reduce the viscosity of the aged material but also to restore compatibility. Objective is to establish the technical feasibility (Phase I) of determining the specifications and operating parameters for producing high quality recycling agents which will allow most/all the old asphalt-based road material to be recycled. It is expected that supercritical fractionation can be used. The advanced road aging simulation procedure will be used to study aging of blends of old asphalt and recycling agents.

Energy Technology Data Exchange (ETDEWEB)

Because of past military operations, lack of upkeep and looting there are now enormous radioactive waste problems in Iraq. These waste problems include destroyed nuclear facilities, uncharacterized radioactive wastes, liquid radioactive waste in underground tanks, wastes related to the production of yellow cake, sealed radioactive sources, activated metals and contaminated metals that must be constantly guarded. Iraq currently lacks the trained personnel, regulatory and physical infrastructure to safely and securely manage these facilities and wastes. In 2005 the International Atomic Energy Agency (IAEA) agreed to organize an international cooperative program to assist Iraq with these issues. Soon after, the Iraq Nuclear Facility Dismantlement and Disposal Program (the NDs Program) was initiated by the U.S. Department of State (DOS) to support the IAEA and ...

Energy Technology Data Exchange (ETDEWEB)

The Kemp's Ridley sea turtle, Lepidochelys kempi, is an endangered species. The National Marine Fisheries Service's Head Start program is part of an international operation to save the turtles from extinction. Under the Head Start program, eggs from the Ridley's only known wild nesting beach at Rancho Nuevo in Mexico are transported to Padre Island on the Texas coast to be hatched. The head start enables the turtles to develop a survival advantage. The principal objective was to develop baseline waste-characterization data required to design a waste-water treatment scheme for the Galveston Head Start facility. As a secondary objective, preliminary testing of some filtration components was undertaken to determine which units were most appropriate for inclusion in a wastewater treatment scheme.

Energy Technology Data Exchange (ETDEWEB)

The most important aim of the title program is to investigate the possibility to convert long-lived actinides and mobile fission products in short-lived and stable isotopes by means of nuclear transmutation and recycling. First, an overview is given of the present situation regarding fission material waste, the origin of such waste in light water reactors and the options for interim and ultimate storage. Next, attention is paid to the aim of the the RAS program, the working method and the results so far of national and international research on the transmutation of actinides and fission products. Speculative expectations for the future are briefly outlined. The report also contains four appendices with technical aspects of the title subject: the RAS program of ECN, chemical aspects of reprocessing fission material, transmutation in fission reactors and in accelerators. 12 figs., 7 tabs., 4 appendices, 57 refs.

International Nuclear Information System (INIS)

The results and techniques of radiographic study on solidification of iron and steel mould castings are described. The study was made to determine the causes of the mold castings defects. The liquid metal is either labelled in the ladle, or relabelled inside the mould in present time intervals. In the former case, the radioactive phosphorus is segregated in the last-solidifying casting locations, and in the latter, the radioactive phosphorous is distributed along the solid-liquid interface at the time of the next addition in turn. The solidification process parameters may be arrived at by the autoradiograms taken in the pipe-sensitive casting sections. Using these data it is possible to proceed to the proper modifications in the steel casting process.

Energy Technology Data Exchange (ETDEWEB)

Los Alamos National Laboratory (LANL) was established during World War II with a single mission -- to design and build an atomic bomb. In the 65 years since, nuclear weapons physics, design and engineering have been the Laboratory's primary and sustaining mission. Experimental and process operations -- and associated cleanout and upgrade activities -- have generated a significant inventory of transuranic (TRU) waste that is stored at LANL's Technical Area 54, Material Disposal Area G (MDA G). When the Waste Isolation Pilot Plant (WIPP) opened its doors in 1999, LANL's TRU inventory totaled about 10,200 m{sup 3}, with a plutonium 239-equivalent curie (PE Ci) content of approximately 250,000 curies. By December 2008, a total of about 2,300 m3 (61,000 PE Ci) had been shipped to WIPP from LANL. This has resulted in a net reduction of about 1,000 m{sup 3} of TRU inventory over that time frame. This ...

Energy Technology Data Exchange (ETDEWEB)

Research is presented on oil and gas technologies, advanced systems for fossil fuels, environmental technologies for remediation and waste management, applied energy science on heavy oil and plastics coprocessing, and fossil fuel and hydrocarbon conversion using hydrogen rich plasma.

Science.gov (United States)

This document provides a technical basis for the revision of chemical effluent limitations guidelines for the Steam Electric Power Industry reflecting the Best Available Technology Economically Achievable (BATEA) for existing sources, New Source Performance Standards (NSPS) and Pretreatment Standards. The analysis of pollutants and the technologies applicable to their control has been based on specific waste streams of concern.

International Nuclear Information System (INIS)

The decommissioning of windscale Pile 2 Chimney resulted in the removal of one of most historically significant and prominent features of the Sellafield site. The project was the first large scale concrete ''free release'' operation to be undertaken on the Sellafield nuclear site, producing 4500 tons of concrete of which 3000 tons was demonstrated to be ''free release''. The paper describes the radiometric techniques employed in the characterisation and segregation of the concrete into low level waste (LLW), very low level waste (VLLW) and free release categories. It examines the robust solutions that were developed to meet the technical and regulatory challenges of the project, which included the definition of free release, the selection of averaging volumes, the testing and validation of the monitoring systems employed for ton quantities of concrete and the identification and removal of small numbers of fuel particles ...

Energy Technology Data Exchange (ETDEWEB)

The LANL Environmental Restoration (ER) Program Office, established in October 1989, is faced with the challenge of assessing and cleaning up nearly 1,8000 potentially hazardous waste sites according to an aggressive corrective action schedule that the Environmental Protection Agency (EPA) mandated on May 23, 1990, in a Resource, Conservation, and Recovery Act (RCRA) Part B Permit. To maximize program efficiency, the ER Program Office will implement a unique management approach designed to maximize the use of laboratory technical expertise. The Installation Work Plan, which provides a blueprint for the program, has been submitted to EPA for review and approval. A work plan for characterization of Technical Area 21, an early plutonium processing facility, is also nearing completion. The feasibility of an expedited cleanup of the Laboratory's worst hazardous waste release has been modelled using ...

Energy Technology Data Exchange (ETDEWEB)

The primary methodology that is used for disposal of municipal solid waste is the use of land fills; 80--85% of the municipal solid waste (MSW) produced in the country currently is land filled. The two other disposal alternatives used are recycling and incineration. Waste-to-energy technology (WTE) which incinerates MSW to produce electricity and/or steam is attractive in other cases since it reduces landfill volume, reduces the consumption of fossil and other fuels, and produces a revenue stream from the sale of the electricity or steam. The gaseous effluents from landfills can also be used to fuel power plants. Recycling and material separation programs can have a substantial impact on the throughput and heating value of MSW collected and thus impact WTE plant economics; the magnitude of the impact will depend upon a number of factors such as what materials and what fraction are separated and recycled, the design of the ...

International Nuclear Information System (INIS)

This paper provides an overview of the state of municipal solid waste (MSW) management in the capital of Cameroon, Yaounde, and suggests some possible solutions for its improvement. The institutional, financial, and physical aspects of MSW management, as well as the livelihoods of the population, were analyzed. Our study revealed that distances and lack of infrastructure have a major impact on waste collection. Garbage bins are systematically mentioned as the primary infrastructure needed by the population in all quarters, whether it be a high or low standard community. The construction of transfer stations and the installation of garbage bins are suggested as a solution to reduce distances between households and garbage bins, thus improving waste collection vehicle accessibility. Transfer stations and garbage bins would enable the official waste collection company to expand its range of services and ...

Energy Technology Data Exchange (ETDEWEB)

An overall systems approach has been applied to develop action plans to support the retrieval and immobilization waste disposal mission. The review concluded that the systems and infrastructure required to support the mission are known. Required systems are either in place or plans have been developed to ensure they exist when needed. The review showed that since October 1996 a robust system engineering approach to establishing integrated Technical Baselines, work breakdown structures, tank farm structure and configurations and work scope and costs has been established itself as part of the culture within TWRS. An analysis of the programmatic, management and technical activities necessary to declare readiness to proceed with execution of the mission demonstrates that the system, people and hardware will be on line and ready to support the private contractors. The systems approach included defining the retrieval and ...

Energy Technology Data Exchange (ETDEWEB)

Consideration of the technical feasibility of Yucca Mountain in Nevada as the site for a high-level nuclear waste repository has led to an intense debate regarding the economic, social, and political impacts of the repository. Impediments to the siting process mean that the nuclear waste problem is being resolved by adhering to the status quo, in which nuclear waste is stored at scattered sites near major population centers. To assess the merits of alternative siting strategies--including both the permanent repository and the status quo- we consider the variables that would be included in a model designed to select (1) the optimal number of disposal facilities, (2) the types of facilities (e.g., permanent repository or monitored retrievable facility), and (3) the geographic location of storage sites. The objective function in the model is an all-inclusive measure of social cost. The intent of the ...

Energy Technology Data Exchange (ETDEWEB)

Competition to produce cast parts of higher quality, lower rejection rate, and lower cost is a fundamental factor in the global economy. To gain an edge on foreign competitors, the US casting industry must cut manufacturing costs and reduce the time from design to market. Casting research and development (R&D) are the key to increasing US compentiveness in the casting arena. Lawrence Livermore National Laboratory (LLNL) is the home of a wide range of R&D projects that push the boundaries of state-of-the art casting. LLNL casting expertise and technology include: casting modeling research and development, including numerical simulation of fluid flow, heat transfer, reaction/solidification kinetics, and part distortion with residual stresses; special facilities to cast toxic material; extensive experience casting metals and nonmetals; advanced measurement and instrumentation systems. Department of Energy (DOE) funding provides the leverage for LLNL to ...

British Library Electronic Table of Contents (United Kingdom)

Summary Electronic textiles are a vanguard of an emerging generation of smart products. They consist of small electronic devices that are seamlessly embedded into clothing and technical textiles. E-textiles provide enhanced functions in a variety of unobtrusive and convenient ways. Like many high-tech products, e-textiles may evolve to become a mass market in the future. In this case, large amounts of difficult-to-recycle products will be discarded. That can result in new waste problems. This article examines the possible end-of-life implications of textile-integrated electronic waste. As a basis for assessment, the innovation trends of e-textiles are reviewed, and an overview of their material composition is provided. Next, scenarios are developed to estimate the magnitude of future e-tex...

Energy Technology Data Exchange (ETDEWEB)

This project seeks to produce sufficient information on the physical and chemical nature of Coolside waste to design and construct physically stable and environmentally safe landfills. Unconfined compressive strength and permeability tests are reported on samples remolded near 90, 95, and 100% of low energy, standard, and modified dry densities. Unconfined compressive strength tests were also performed on some of the samples after permeability tests were completed. Swell tests were initiated on samples from Coolside pilot plant run {number_sign}2 and on a FBC hydrated ash remolded near 95% of standard density and optimum moisture content.

Energy Technology Data Exchange (ETDEWEB)

This Waste Management Plant (WMP) for the Bear Creek Valley Treatability Study addresses waste management requirements for the Oak Ridge Y-12 Plant. The study is intended to produce treatment performance data required to design a treatment system for contaminated groundwater. The treatability study will consist of an evaluation of various treatment media including: continuous column tests, with up to six columns being employed to evaluate the performance of different media in the treatment of groundwater; an evaluation of the denitrifying capacity and metal uptake capacity of a wetland system; and the long-term denitrifying capacity and metal uptake capacity of algal mats. The Sampling and Analysis Plan (SAP) covers the project description, technical objectives, procedures, and planned work activities in greater detail. The Health and Safety Plan (HASP) addresses the health and safety concerns and requirements for the ...

Science.gov (United States)

The Nuclear Regulatory Commission stipulates in 10 CFR 61 that disposed low-level radioactive waste (LLW) be stabilized. To provide guidance to disposal vendors and nuclear station waste generators for implementing those requirements, the NRC developed the Technical Position on Waste Form, Revision 1. That document details a specified set of recommended testing procedures and criteria, including several tests for determining the biodegradation properties of waste forms. Cement has been widely used to solidify LLW; however, the resulting waste forms are sometimes susceptible to failure due to the actions of waste constituents, stress, and environment. The purpose of this research program is to develop modified microbial degradation test procedures that will be more appropriate than the existing procedures for evaluating the effects of ...

Energy Technology Data Exchange (ETDEWEB)

Indicators are important tools for communicating and making accessible scientific and technical information to policymakers and the general public. They therefore play an important role in transforming information into action. Worldwide, many initiatives are underway to construct indicators for a variety of purposes, including those for reporting on sustainable development. This paper briefly describes the attempts made so far, but stresses that the users of the indicators should play a greater role in indicator construction. In developing countries, a substantial lack of data has meant that specific policy formulation may develop without adequate technical input. In developed countries also, data gaps may hinder policy formulation, implementation, and evaluation. However, the development of indicators as tools to assist in the management of hazardous wastes and toxic chemicals is still in the early stages of formulation. A ...

Energy Technology Data Exchange (ETDEWEB)

In order to realize improve of reliability and economy by duplicate production, rapid supply of repair parts from standardized storage, such were expected as to have continuous order of standardized plant, to ignore site condition, to avoid expansion of regulatory requirement. Standardization program was planned to limitedly promote standardization of safety-related design concept, major specification and basic system composition of reactor and primary systems. The area of standardization had been tried to expand to BOP such as general arrangement and rad-waste system.

International Nuclear Information System (INIS)

The purpose of the Ocean FUSRAP Program, which began in March 1981, is to assess the technical, environmental, and institutional feasibility of disposing, in the ocean and on the ocean floor, of FUSRAP waste which contains traces of natural radioactive materials. The initial planning has focused on the Middlesex, New Jersey, Sampling Plant site and surrounding properties, which contain on the order of 100,000 metric tons of material. The Belgian Congo uranium ore and other uranium ores used by the United States were handled at the sampling plant site and have since been removed.

Energy Technology Data Exchange (ETDEWEB)

Primary design criterion for this division`s education activities is directly related to meeting the goal of environmental compliance on an accelerated basis and cleanup of the 1989 inventory of inactive sites and facilities by the year 2019. Therefore, the division`s efforts are directed toward stimulating knowledge and capability to achieve the goals while contributing to DOE`s overall goal of increasing scientific, mathematical, and technical literacy and competency. This annual report is divided into: overview, workforce development, academic partnerships, scholarships/fellowships, environmental restoration and waste management employment program, community colleges, outreach, evaluation, and principal DOE contacts.

Energy Technology Data Exchange (ETDEWEB)

Although computer simulation has played a central role in the study of nucleation and growth since the earliest molecular dynamics simulations almost 50 years ago, confusion surrounding the effect of finite size on such simulations have limited their applicability. Modeling solidification in molten tantalum on the BlueGene/L computer, we report here on the first atomistic simulation of solidification that verifies independence from finite size effects during the entire nucleation and growth process, up to the onset of coarsening. We show that finite size scaling theory explains the observed maximal grain sizes for systems up to about 8,000,000 atoms. For larger simulations, a cross-over from finite size scaling to more physical size-independent behavior is observed.

CERN Document Server

The Principles of Radioactive Waste Management

International Nuclear Information System (INIS)

The primary function of the Waste Handling Shaft (WHS) at the Waste Isolation Pilot Plant (WIPP) is to permit the transfer of radioactive waste from the surface waste handling building to the underground storage area. It also serves as an intake shaft for small volumes of air during normal storage operations and as an emergency escape route. Part of the construction was the placement of a concrete liner and steel reinforced key in 1984. During a routine shaft inspection in May 1990, some degradation of the WHS concrete liner was observed between the depths of 800 and 900 feet below the ground surface. Detailed investigations of the liner had been carried out by Sandia National Laboratories and by Westinghouse Electric Corporation Waste Isolation Division (WID) through Lankard Materials Laboratory. Observations, reports, and data support the conclusion that the concrete degradation, ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of the New Mexico Environmental Evaluation Group (EEG) is to conduct an independent technical evaluation of the Waste Isolation Pilot Plant (WIPP) Project to ensure the protection of the public health and safety and the environment. The WIPP Project, located in southeastern New Mexico, is being constructed as a repository for the disposal of transuranic (TRU) radioactive wastes generated by the national defense programs. The EEG was established in 1978 with funds provided by the U.S. Department of Energy (DOE) to the State of New Mexico. Public Law 100-456, the National Defense Authorization Act, Fiscal Year 1989, Section 1433, assigned EEG to the New Mexico Institute of Mining and Technology and continued the original contract DE-AC04-79AL10752 through DOE contract DE-AC04-89AL58309. The National Defense Authorization Act for Fiscal Year 1994, Public Law 103-160, continues the authorization. EEG performs ...

International Nuclear Information System (INIS)

The U.S. Department of Energy (DOE) has developed comparatively detailed quality assurance requirements for the high-level radioactive waste disposal systems. Quality assurance is recognized as a key issue for confidence building and smooth implementation of the HLW program in Japan, and Japan is at an initial phase of repository development. Then the quality assurance requirements at site research and site selection, site characterization, and site suitability analysis used in the Yucca Mountain project were examined in detail and comprehensive descriptions were developed using flow charts. Additionally, the applicability to the Japan high-level radioactive waste disposal project was studied. The examination and study were performed for the following QA requirements: The requirements that have the relative importance at site research and site selection, site characterization, and site suitability analysis (such as planning and performing ...

International Nuclear Information System (INIS)

The 2nd periodical inspection was carried out on the asphalt solidification facility and the incinerator in Unit 2 of the Sendai Nuclear Power Station from November 5 to 28, 1985. Inspection was made in radiation control facility and disposal facility. By external appearance, disassembly, function and performance tests there were observed no abnormalities. The personnel exposure doses during the inspection were below the permissible level. In the inspection, improvement etc. works were not done. (Mori, K.).

Energy Technology Data Exchange (ETDEWEB)

North Carolina is in the process of siting a LLRW disposal facility as the next host state for the Southwest Compact. After two years of site characterization studies at two technically challenging sites, the LLRW Management Authority (the Authority), will submit a license application for the preferred site. One potential site is in unconsolidated Tertiary and Cretaceous deposits of the inner Coastal Plain, the other in fractured sedimentary rocks of the Triassic Deep River Basin. Involved since 1986, the North Carolina Geological Survey (NCGS) provides technical advice to the Division of radiation Protection, the state regulatory agency authorized to approve or deny a license. With the multi-million dollar project behind schedule, and millions of dollars over budget, in February 1992 the Southeast Compact Commission established three project milestones (1) submit license application by December 31, 1993; (2) approve license by March 15, 1994; ...

Science.gov (United States)

... of waste food generated at McMurdo Station. Some of the difficulties of disposing of waste food ... change waste generation or management at the site? Yes. This will be a temporary waste management ...

International Nuclear Information System (INIS)

This publication identifies conditions which affect (either increase or decrease) public concern for and political acceptance of the development and implementation of programmes for geological disposal of long lived radioactive waste. It also looks at how interested citizens can be associated in the decision making process in such a way that their input enriches the outcome of a more socially robust and sustainable solution. The publication also considers how to optimize risk management, addressing the needs and expectations of the public and of other relevant stakeholders. Factors of relevance for societal acceptance conditions are identified for the different stages of a repository programme and implementation process, from policy development to the realization of the repository itself. Further, they are described and analysed through case studies from several countries, illustrating the added value of broadening the technical dimension with ...

International Nuclear Information System (INIS)

Naturally occurring radionuclides are present in most material. The most common naturally occurring radionuclides in material are those of the uranium and thorium series and potassium-40. This material is commonly referred to as Naturally Occurring Radioactive Material (NORM). In some material the levels of naturally occurring radionuclides are significantly higher, to the extent that regulatory control may be required for radiation protection purposes. Regulation of NORM presents a range of new challenges for both regulators and operators. Unlike more traditional industries dealing with radionuclides, NORM industries have generally not had any radiological oversight and, for example, are not equipped for radiological monitoring. Some consumer goods containing NORM, which have not traditionally been considered as a radiological problem (such as some fertilizers), may require regulation and this may have social and economic consequences. The transport and disposal of NORM are also a ...

International Nuclear Information System (INIS)

The IAEA attaches great importance to the dissemination of information that can assist Member States with the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support the nuclear fuel cycle and nuclear applications, including management of the legacy of past practices and accidents. In this connection, the IAEA has initiated a comprehensive programme of work covering all aspects of environmental remediation: - Technical and non-technical factors, including costs, that influence environmental remediation strategies and pertinent decision making; - Site characterization techniques and strategies; - Assessment of remediation technologies; - Techniques and strategies for post-remediation compliance monitoring; - Special issues such as the remediation of sites with dispersed radioactive contamination or mixed contamination by hazardous and radioactive substances. Experience in Member ...

Energy Technology Data Exchange (ETDEWEB)

The pollution prevention program operated by the Health Department of Boulder County is called Business Partners for a Clean Environment (Business Partners). It is a cooperative effort among local businesses, the City of Boulder, Boulder County, and the Boulder Chamber of Commerce. This nonregulatory, incentive-based program provides industry with pollution prevention information and technical assistance necessary to reduce and/or eliminate environmental waste. This paper provides an overview of the program development, creation of partnerships and trust, and some of the results from implementation of the program. Following the first 18 months of the program, 35 businesses were recognized as Business Partners. The Business Partners program has also received an achievement award from the National Association of Counties for promoting {open_quotes}responsible, responsive, and effective government{close_quotes} and two governor`s awards from the ...

Energy Technology Data Exchange (ETDEWEB)

French law should not be very affected when the NSC enters into force in France. This results from the fact that French law has already achieved most of the `work` to be done in the field of safety of nuclear installations as it integrated the concept of `safety culture` (i.e. high level of safety for nuclear installations) which is, actually, the main objective of this convention. The elaboration of this convention on safety of nuclear power plants took approximately 3 years. The success (i.e. adoption of the draft text by the Diplomatic Conference) was made possible because of the large technical consensus existing among experts in that field. This means that if we intend to do the same in the field of radioactive waste management, we have to get first a similar consensus on fundamental adequate principles. (orig./HP)

Energy Technology Data Exchange (ETDEWEB)

In this book are found technical and scientific papers on the main works of the Direction of the Fuel Cycle (DCC) in France. The study fields are: the up-side of the nuclear fuel cycle with theoretical studies (plasma simulation) and technological developments and instrumentation (lasers diodes, carbides plasma projection, carbon 13 enrichment); the down-side nuclear fuel cycle with theoretical studies (ion Eu{sup 3+} complexation simulation, decay simulation, uranium and plutonium diffusion study, electrolyser operating simulation), scenario studies ( recycling, wastes management), experimental studies; dismantling and cleaning (soils cleaning, surface-active agent for decontamination, fault tree analysis); analysis with expert systems and mass spectrometry. (A.L.B.)

Energy Technology Data Exchange (ETDEWEB)

This conference provided a forum for discussing advances in the application of engineering principles and practices dealing with biological systems for the production of food, bioproducts and energy. The discussions focused on engineering practices in agriculture, forestry, bioresources, biochemistry and biosystems. The sessions of the conference were entitled: renewable energy and biofuels; food and bioproducts; odour and greenhouse gases; soil and water; waste management and bioresiduals; animal welfare and production; grain storage; machinery systems; structures and biocomposites; and, agricultural production. The conference also featured a workshop on modeling material and energy flows through agro-ecosystems. In addition to 22 posters, the conference featured 100 presentations, of which 8 have been catalogued separately for inclusion in this database. refs., tabs., figs.

Energy Technology Data Exchange (ETDEWEB)

The oil shale PCTM for Modified In Situ Oil Shale Retorting combined with Lurgi Surface Retorting addresses the application of this combination of technologies to the development of oil shale resources in the western United States. This manual describes the combined plant using Lurgi surface retorting technology (developed by Lurgi Kohle and Mineralotechnik GmbH, West Germany) and the Modified In Situ process (developed by Occidental Oil Shale, Inc.) proposed by Occidental Oil Shale, Inc. and Tenneco Shale Oil Company for use in the development of their Federal oil shale lease Tract C-b in western Colorado. Since details regarding waste streams and control technologies for the Lurgi process are presented in a separate PCTM, this document focuses principally on the Modified In Situ process.

International Nuclear Information System (INIS)

The design, construction and operation of a pilot plant are often important stages in the development of a project for the production of uranium concentrates. Since building and operating a pilot plant is very costly and may not always be required, it is important that such a plant be built only after several prerequisites have been met. The main purpose of this guidebook is to discuss the objectives of a pilot plant and its proper role in the overall project. Given the wide range of conditions under which a pilot plant may be designed and operated, it is not possible to provide specific details. Instead, this book discusses the rationale for a pilot plant and provides guidelines with suggested solutions for a variety of problems that may be encountered. This guidebook is part of a series of Technical Reports on uranium ore processing being prepared by the IAEA's Division of Nuclear Fuel Cycle and Waste Management. 42 refs, 7 figs, 3 tabs.

International Nuclear Information System (INIS)

The foundation conducts an environmental monitoring and surveillance program over an area covering much of the upper Snake River Plain and provide environmental education and support services related to INEL natural resource issues. Also, the foundation, with its university affiliates, conducts ecological and radioecological research on the Idaho National Environmental Research Park. This research benefits major DOE-ID programs including waste management, environmental restoration, spent nuclear fuels, and land management issues. Major accomplishments during CY1995 can be divided into five categories: environmental surveillance program, environmental education, environmental services and support, ecological risk assessment, and research benefitting the DOE-ID mission.

Energy Technology Data Exchange (ETDEWEB)

Environmental surveillance and public information are translated in 2000 by numerous actions. To improve the public information, A.C.R.O. concerns its main efforts on the development of the consumer technical information available on-line via its web site and in its regular publication 'the nuclear chronicle'. A new publication, the A.C.R.O. journal is made to answer to more acute questions as waste burying. Besides, the participation of the A.C.R.O. at various local commissions of information (C.L.I.) as well as at the superior council of the safety and nuclear information ( C.S.S.I.N.) stays an essential action. (N.C.)

International Nuclear Information System (INIS)

A method is described for immobilizing or solidifying waste material, which includes blending the waste material with powdered metal and subjecting the mixture of waste material and powdered metal to high pressure. (author).

Energy Technology Data Exchange (ETDEWEB)

the medium to long freezing range alloys of aluminum such as A356, A357, A206, 319 for example are known to exhibit dispersed porosity, which is recognized as a factor affecting ductility, fracture toughness, and fatigue resistance of light alloy castings. The local thermal environment, for example, temperature gradient and freezing from velocity, affect the mode of solidification which, along with alloy composition, heat treatment, oxide film occlusion, hydrogen content, and the extent to which the alloy contracts on solidification, combine to exert strong effects on the porosity formation in such alloys. In addition to such factors, the availability of liquid metal and its ability to flow through the partially solidified casting, which will be affect by the pressure in the liquid metal, must also be considered. The supply of molten metal will thus be controlled by the volume of the riser available for feeding the particular casting location, ...

Energy Technology Data Exchange (ETDEWEB)

The thermal and heat transfer characteristics of stearic acid during the solidification processes were investigated experimentally in a vertical annulus energy storage system. The temperature distribution and temperature variations with time at different radial positions during the freezing processes were obtained. The thermal characteristics of the stearic acid, including movement of the solid-liquid interface in the radial direction, and the effects of Reynolds number on the heat transfer parameters were studied. The heat flux was estimated by using a simple approximate model. A new copper fin was designed and fixed to the electrical heating rod to enhance the thermal conductivity of the stearic acid. The results show that the new fin can enhance both the conduction and the natural convection heat transfer of the PCM, and the enhancement factor during solidification is estimated to be as high as 250%. The effect of the fin width on the ...

International Nuclear Information System (INIS)

In the early sixties it was decided to investigate salt formations on its suitability to host heat generating radioactive waste in Germany. In the reference repository concept consequently the emplacement of vitrified waste canisters in deep vertical boreholes inside a salt mine was considered whereas spent fuel should be disposed of in self shielding casks (type POLLUX) in horizontal drifts. The POLLUX casks, 65 t heavy carbon steel casks, will be laid down on the floor of a horizontal drift in one of the disposal zones to be constructed in the salt dome at the 870 m level. The space between casks and drift walls will be backfilled with crushed salt. The transport, the handling und the emplacement of POLLUX casks were subject of successfully performed demonstration and in situ tests in the nineties and resulted in an adjustment of the atomic law. The borehole disposal concept comprises the emplacement of unshielded canisters with vitrified HLW ...

Energy Technology Data Exchange (ETDEWEB)

This Current Year Work Plan presents in detail a description of the activities to be performed by the Joint Integration Office/RI during FY86. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO/RI by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO/RI tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance development, task monitoring, task progress information gathering and reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, ...

Energy Technology Data Exchange (ETDEWEB)

The subscale Varestraint test has been used to determine the relative hot cracking susceptibility of the fusion zone in four commercial heats of alloy 800. Although all four heats were susceptible to cracking, one heat exhibited a significant increase in cracking relative to the other three. Optical metallography revealed that nearly all the cracking was localized along fusion zone grain boundaries. Microprobe analysis of the grain boundaries detected high concentrations of titanium, silicon, and niobium resulting from partitioning during solidification. The fusion zone hot cracking mechanism in alloy 800 involves the complex interaction of titanium, silicon, niobium, and carbon along the solidification boundaries. SEM and Auger analyses of the hot crack fracture surfaces revealed the presence of (Ti, Nb)-rich carbides, suggesting that these particles precipitate from the liquid which solidifies last on the fracture surface. 23 references.

Energy Technology Data Exchange (ETDEWEB)

In an effort to minimize the distortion of bearing steel rings during the production process, 100Cr6 steel billets are spray formed with a unique cooling control system to control the cooling and solidification behavior of the deposits. Effects of heating around the deposits, gas cooling at the substrate bottom and the gas flow over the deposits are investigated both by numerical simulation and experiment. Porosity profiles and microstructures of spray formed bearing steel are examined and evaluated. The investigation results show that the thermal boundary conditions of the deposits play important roles on the cooling and solidification behavior of the deposits, especially at the deposit periphery. Porosity in the 100Cr6 bearing steel deposit can be reduced significantly with the special cooling control system.

Wastenet

...Species - see CITES Trade of Dangerous Chemicals Transport and Environment U Urban Environment Use of natural resources V Volatile Organic Compounds W Waste Landfills Waste electrical and electronic equipment - see WEEE Waste incineration Waste legislation - reporting Waste management planning Waste oils Waste shipments Waste water - see Urban waste water Water Bathing Water Drinking water Floods Marine environment Urban waste water Water Framework Directive WEEE - Waste Electric and Electronic Equipment Wildlife ...

CERN Document Server

Regulatory Control of Radioactive Waste Management

KoreaScience (Korea)

Full Text Available

International Science & Technology Center (ISTC)

Methods of Decontamination, Utilization, and Deactivation of Liquid Radioactive Wastes

Science.gov (United States)

... wood, kitchen wastes, and human faeces with the ash from such burning deposited and retained in an ...

International Science & Technology Center (ISTC)

Development, Investigation and Improvement of a System of Incinerating Crop Production Wastes in Small Capacity Boilers

Energy Technology Data Exchange (ETDEWEB)

This volume contains 5 appendices. Title listing are: technologies for recovery of transuranics; nondestructive assay of TRU contaminated wastes; miscellaneous waste characteristics; acceptance criteria for TRU waste; and TRU waste treatment technologies.

Wastenet

1 to the operator of a waste collective system by an agreement or contract. The conditions for the ...Fees of the waste collective system are subject to the supervision of the authority responsible for market surveillance. ...The operator of waste collection system collects wastes from producers and holder and transports these to a collection

Energy Technology Data Exchange (ETDEWEB)

This technical memorandum (TM) documents the 1995 characterization of eight underground radioactive waste tanks at Oak Ridge National Laboratory (ORNL). These tanks belong to the Gunite and Associated Tanks (GAAT) operable unit, and the characterization is part of the ongoing GAAT remedial investigation/feasibility study (RI/FS) process. This TM reports both field observations and analytical results; analytical results are also available from the Oak Ridge Environmental Information System (OREIS) data base under the project name GAAT (PROJ-NAME = GAAT). This characterization effort (Phase II) was a follow-up to the {open_quotes}Phase I{close_quotes} sampling campaign reported in Results of Fall 1994 Sampling of Gunite and Associated Tanks at the Oak Ridge National Laboratory, Oak Ridge, Tennessee, ORNL/ER/Sub/87-99053/74, June 1995. The information contained here should be used in conjunction with that in the previous TM. The sampling plan is ...

Energy Technology Data Exchange (ETDEWEB)

The precipitation of heavy metals as hydroxides is the standard technique for the decontamination of waste water streams polluted by these elements. On the other side, progress in research has been made concerning the biosorption onto dead biomass and bioprecipitation supported by physiologically active bacteria. As the aim of this study, a flexible strategy has been envisaged cleaning a waste water with definite heavy metal load underlying the process mentioned above. Suitable bacteria were enriched and the process was tested in a technical plant. As result, a very high efficiency of heavy metal elimination has been found. The field of application covered by the acquired process is identical with the whole range of the waste water streams polluted by heavy metals. In addition, a second stage may be necessary if there are any further contaminants to be removed. (orig.) [Deutsch] Bei der Reinigung von ...

Energy Technology Data Exchange (ETDEWEB)

This report is a compilation of worksheets from the waste management units of Savannah River Plant. Information is presented on the following: Solid Waste Management Units having received hazardous waste or hazardous constituents with a known release to the environment; Solid Waste Management Units having received hazardous waste or hazardous constituents with no known release to the environment; Solid Waste Management Units having received no hazardous waste or hazardous constituents; Waste Management Units having received source; and special nuclear, or byproduct material only.

Science.gov (United States)

The authors solve the two-dimensional stefan problem of solidification in a half-space, where the heat flux at the wall is a slightly varying function of positioning along the wall, by means of a large Stefan number approximation (which turns out to be equivalent to a small time solution), and then by means of the Heat Balance Integral Method, which is valid for all time, and which agrees with the large Stefan number solution for small times. A representative solution is given for a particular form of the heat flux perturbation.

Energy Technology Data Exchange (ETDEWEB)

Four subprojects were completed: development and evaluation of die coatings, accelerated die life characterization of die materials, evaluation of fluid flow and solidification modeling programs, selection and characterization of Al-based die casting alloys, and influence of die materials and coatings on die casting quality.

Energy Technology Data Exchange (ETDEWEB)

The report investigates a number of joining techniques, i.e. isothermal solidification, ultrasonic welding, thermocompression, and glueing. (HW) [Deutsch] In diesem Vorhaben wurden verschiedene Verbindungstechniken untersucht: Isotherme Erstarrung; Ultraschall-Schweissen; Thermokompression; Leitkleben. (HW)

ScienceCinema

...different sparking language english ? ...

Energy Technology Data Exchange (ETDEWEB)

The paper deals with the disposal of radioactive waste and the plans for dealing with solid wastes of intermediate and low levels of activity, which are the responsibility of NIREX. NIREX is an executive body which co-ordinates the waste-disposal plans of the main radioactive waste producers. The disposal routes for the active wastes are described including the deep disposal of wastes containing material that will remain active for thousands of years. Requirements for deep burial are outlined with reference to the geology and hydrogeology of the site. Monitoring, maintenance and surveillance are mentioned for the protection of the public.

Science.gov (United States)

... Scientists. NASA/DoD Aerospace Knowledge Diffusion Research Project. Descriptive Note : Technical memo. rept. no. 29,. ...

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing on a county by county basis the agricultural crop, agricultural wastes, municipal wastes, and industrial wastes of Virginia that are potential biomass energy sources.

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing on a county by county basis the agricultural crop, agricultural wastes, municipal wastes and industrial wastes of Alabama that are potential biomass energy sources.

Science.gov (United States)

Lunar resource utilization has focused principally on the extraction of oxygen from the lunar regolith. A number of schemes have been proposed for oxygen extraction from Ilmenite and Anorthite. Serendipitously, these schemes have as their by-products (or more directly as their "waste products"), materials needed for the fabrication of thin film silicon solar cells. Thus lunar surface possesses both the elemental components needed for the fabrication of silicon solar cells and a vacuum environment that allows for vacuum deposition of thin film solar cells directly on the surface of the Moon without the need for vacuum chambers. In support of the US space exploration initiative a new architecture for the production of thin film solar cells on directly on the lunar surface is proposed. The paper discusses experimental data on the fabrication and properties of lunar glass substrates, evaporated lunar regolith thin films (anti-reflect coatings and insulators), and ...

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the major activities conducted in the Chemical and Energy Research Section of the Chemical Technology Division (CTD) at Oak Ridge National Laboratory (ORNL) during the period January--March 1997. Created in March 1997 when the CTD Chemical Development and Energy Research sections were combined, the Chemical and Energy Research Section conducts basic and applied research and development in chemical engineering, applied chemistry, and bioprocessing, with an emphasis on energy-driven technologies and advanced chemical separations for nuclear and waste applications. The report describes the various tasks performed within seven major areas of research: Hot Cell Operations, Process Chemistry and Thermodynamics, Molten Salt Reactor Experiment (MSRE) Remediation Studies, Chemistry Research, Separations and Materials Synthesis, Solution Thermodynamics, and Biotechnology Research. The name of a technical contact is included with ...

Energy Technology Data Exchange (ETDEWEB)

With the November 1989 formation of the Office of Technology Development (OTD) within the Office of Environmental Restoration and Waste Management (EM) came the responsibility to develop programs to ensurethat enough trained and educated people would be available to support the achievement of EM's 30-year goal. This mission responsibility derives from public policy and Departmental environmental management requirements. Within DOE, urgency to move forward resulted from the assumptions (1) that the current workforce was insufficiently prepared for the transition from a production mission to a mission of environmental compliance and cleanup; and (2) that, given current trends and forecasts, the national education infrastructure was unlikely to yield the scientists, engineers, and technicians to meet future DOE workforce needs, especially in the case of women and minorities who, projected to make up two-thirds of the net entering workforce by the year 2000, ...

Energy Technology Data Exchange (ETDEWEB)

The Hazardous Material Management and Emergency Response Training and Education Center -- known simply as HAMMER -- is being developed to assist the US Department of Energy (DOE) and others dedicated to improving worker health, safety and productivity. HAMMER is a training and education program for hazardous material, waste management, and emergency response workers. HAMMER is managed by the DOE Richland Operations Office under Work Breakdown Structure (8.2). The 1996 Multi-Year Program Plan (MYPP) includes the Execution Year data and provides the information for Programmatic Fiscal Year Site Management System Execution Baseline, as well as the detailed work plan for performance evaluation of the authorized work. The MYPP incorporates various planning methodologies to define the program and provides essential program integration, and a fully developed technical, cost, and schedule baseline. The MYPP will be utilized by WHC Program and ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to develop the radioisotope tracer technology, which can be used in solving industrial and environmental problems and to build a strong tracer group to support the local industries. In relation to the tracer technology in 1999, experiments to estimate the efficiencies of a sludge digester of a waste water treatment plant and a submerged biological reactor of a dye industry were conducted. As a result, the tracer technology for optimization of facilities related to wastewater treatment has been developed and is believed to contribute to improve their operation efficiency. The quantification of the experimental result was attempted to improve the confidence of tracer technology by ECRIN program which basically uses the MCNP simulation principle. Using thin layer activation technique, wear of tappet shim was estimated. Thin layer surface of a tappet shim was irradiated by proton beam and the correlation between the measured activity loss ...

International Nuclear Information System (INIS)

The objective of this report was to evaluate four possible alternative methods of preparing and packaging spent fuel assemblies for geologic disposal against the Reference Process of unmodified spent fuel. The four alternative processes were: (1) End fitting removal, (2) Fission gas venting and resealing, (3) Fuel bundle disassembly and close packing of fuel pins, and (4) Fuel shearing and immobilization. Systems analysis was used to develop a basis of comparison of the alternatives. Conceptual processes and facility layouts were devised for each of the alternatives, based on technology deemed feasible for the purpose. Assessments were made of 15 principal attributes from the technical, operational, safety/risk, and economic considerations related to each of the alternatives, including both the surface packaging and underground repository operations. Specific attributes of the alternative processes were evaluated by assigning a number for each that expressed its ...

Energy Technology Data Exchange (ETDEWEB)

This Report of activity displays the work developed at Centre d`Etude Nucleaires de Bordeaux-Gradignan (CENBG) in the period 1995-1996. A number of 68 short progress notes are presented in the fields of Cosmic particles (3), Nuclear Astrophysics (4), High Spins-Large Deformations (8), Basic Interactions (9), Exotic Nuclei (10), Hybrid Systems (4), Theoretical Physics (28), Cellular Microanalysis by means of Nuclear Probes (3) and Technical Development (3). The main problems attacked at CENBG, established as orientations by scientific board of IN2P3 (CENBG is a UMR of Bordeaux-1 Univ. and CNRS-IN2P3) are the following: the research of Majorana/Dirac nature of neutrino (in the framework of NEMO Experiment) in relation with the problem of origin of mass in the Universe and the cosmological puzzle of dark matter, the investigation of the origin of high energy (20 to 200 GeV) cosmic radiation (in the framework of CELESTE Experiment), the study of extreme issues in ...

Energy Technology Data Exchange (ETDEWEB)

This revision of the APT Waste Management Plan details the waste management requirements and issues specific to the APT plant for design considerations, construction, and operation. The APT Waste Management Plan is by its nature a living document and will be reviewed at least annually and revised as required.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

UK PubMed Central (United Kingdom)

Electronic waste or e-waste is one of the rapidly growing problems of the world. E-waste comprises of a multitude of components, some containing toxic substances that can have an adverse impact on human...Full Text Available

Science.gov (United States)

PMID:21769853

Science.gov (United States)

...2009-07-01 false Definition of solid waste. 261.2 Section 261.2 Protection...PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) IDENTIFICATION AND LISTING OF HAZARDOUS WASTE General § 261.2 Definition...

International Nuclear Information System (INIS)

Illicit trafficking of nuclear and other radioactive material has been an issue of concern since the first seizures in the early 1990s. By the end of 2004 Member States had confirmed 540 cases, while about another 500 remain unconfirmed. Most of the confirmed cases have a criminal dimension, even if they were not for known terrorist purposes. The attacks of September 2001 in the USA dramatically emphasized the requirement for the enhanced control and security of nuclear and other radioactive material. In response to a resolution by the IAEA General Conference in September 2002 the IAEA has adopted an integrated approach to protection against nuclear terrorism. This brings together IAEA activities concerned with the physical protection of nuclear material and nuclear installations, nuclear material accountancy, detection and response to illicit nuclear trafficking, the security and safety of radioactive sources, emergency response measures - including pre-emergency measures in Member ...

Energy Technology Data Exchange (ETDEWEB)

The RCP method was designed as a residue-optimised alternative to the thermally optimised grate firing of residual wastes. Its technical realisation and development to market maturity took no more than 5 years. In the first process stage the waste is converted to high-carbon pyrolysis charcoal and high-rank gas in the absence of oxygen. In the second stage these substances are oxidised by addition of oxygen. The resulting temperature causes the non-combustible constituents of the slag to melt. In a third, optional, stage this molten slag can be liberated of (heavy) metals to such an extent that it can subsequently be used directly as additive for grinding. Further exhaust gas treatment is facilitated by the use of a circulatory fluidised-bed secondary combustion chamber. Despite the reduced flue gas volume and resultant higher pollutant concentrations in the crude gas, overall emissions are lower than in conventional ...

International Nuclear Information System (INIS)

The Office of Civilian Radioactive Waste Management (OCRWM) must, among other things, be equipped to readily produce, file, store, access, retrieve, and transfer a wide variety of technical and institutional data and information. The data and information regularly produced by members of the OCRWM Program supports, and will continue to support, a wide range of program activities. Some of the more important of these information communication-related activities include: supporting the preparation, submittal, and review of a license application to the Nuclear Regulatory Commission (NRC) to authorize the construction of a geologic repository; responding to requests for information from parties affected by and/or interested in the program; and providing evidence of compliance with all relevant Federal, State, local, and Indian Tribe regulations, statutes, and/or treaties. The OCRWM Telecommunications Network Plan (TNP) is intended to identify, as ...

International Nuclear Information System (INIS)

This paper reports about in-situ corrosion studies on selected materials for long-term resistant high-level waste (HLW) packagings acting as a barrier in a rock salt repository. The materials (Ti 99.8-Pd, Hastelloy C4 and five iron-base materials) were investigated in heated boreholes in the Asse salt mine under simulated HLW disposal conditions prevailing in normal operation of repository and in certain accident scenarios. The experiments under normal operating conditions were performed at temperatures of 120 deg. C to 210 deg. C (vertical temperature profile in the boreholes) without and with gamma irradiation (3#centre dot#10"2 Gy/h, Co-60 source) within the framework of the German/US Brine Migration Test. In these experiments only small amounts of migrated brine inclusions (NaCl-rich) from the rock salt were present as corrosion medium. In the experiments carried out under simulated accident conditions with intrusion of larger amounts of NaCl brine into the HLW ...

Energy Technology Data Exchange (ETDEWEB)

Drastic changes in waste management procedures are expected from the German Municipal Waste Disposal Regulations which became effective on June 1, 1993. Waste disposal will be subject to certain restrictions which, e.g. demand that wastes must be pretreated and inerted before they are stored. These regulations favor thermal waste disposal methods such as the carbonization/combustion method which is planned for a commercial-scale plant in the city of Fuerth. (orig./BBR)

CERN Document Server

Safe management of wastes from the mining and milling of Uranium and Thorium ores

Science.gov (United States)

One of the major problems associated with solid waste processing technologies is the release of

Science.gov (United States)

This request is submitted to seek interim approval to operate a Toxic Substances Control Act (TSCA) of 1976 chemical waste landfill for the disposal of polychlorinated biphenyl (PCB) waste. Operation of a chemical waste landfill for disposal of PCB waste ...

Energy Technology Data Exchange (ETDEWEB)

Considering the fact that more than 40% of all household wastes are organic wastes composting could be an excellent relief and complement to other waste disposal methods (e.g. combustion or direct landfills). Provided the right conditions household wastes could be composted together with sewage sludges and manures. The paper discusses the legal aspects, quantitative evaluations, conveying systems, as well as the compost utilization and marketing aspects valid for the Federal Republic of Germany.

Energy Technology Data Exchange (ETDEWEB)

Following the executive summary, this document contains the following: (1) waste management facilities design objectives; (2) AVLIS production plant wastes; (3) waste management design criteria; (4) waste management plan description; and (5) waste management plan implementation. 17 figures, 18 tables.

Energy Technology Data Exchange (ETDEWEB)

Better properties of magnesium make it a natural choice for use as an anode material in rechargeable batteries. However, the magnesium alloy thin sheets used in rechargeable batteries were produced by ingot casting and rolling. That technology was so complex and the cost was high. Rapidly solidification by melt spinning is an effect way to solve that problem. In this paper, the technology of rapidly solidified (RS) ribbons in Mg-3%Al-1%Zn-0.2%Mn alloy has been investigated using melt spinning technique. The effect of wheel speed on thickness and microhardness of the ribbons is presented. Microhardness is found to increase with the wheel speed. Rapidly solidification leads to small grains (1{proportional_to}2 {mu}m). The plasticity of the ribbons was well. The quantity of Mg{sub 17}Al{sub 12} decreases with the increase in wheel speed. When the wheel speed reaches 1600 rpm, no Mg{sub 17}Al{sub 12} phase precipitates. As the increase of the wheel ...

Energy Technology Data Exchange (ETDEWEB)

An accelerated crucible rotation (ACR) technique was applied to the Bridgman (B) directional solidification of Al-Cu hypoeutectic and eutectic alloys. For Al-4.5% Cu hypoeutectic alloys. The development of dendrites was prevented and the cellular spacing was reduced by forced convection in the ACR-B process. For the Al-CuAl{sub 2} eutectic alloy, maximum rotation rates of 100, 200, 300 and 400 rpm were adopted, and the growth rate R was varied between 5 and 60 {mu}m/s. The results show that the periodic structure related to the crucible rotation periods occurs when the Reynold's number Re > 500, and that the average eutectic spacing decreases with the increase of Re. It is found that the convection increases the temperature gradient in front of the liquid/solid interface and reduces the depth of the concave interface, depending on Re and R. The convection also changes the solute distribution around the tips of the cells or dendrites or in front of ...

Energy Technology Data Exchange (ETDEWEB)

Spray forming is an advanced materials processing technology that converts a bulk liquid metal to a near-net-shape solid by depositing atomized droplets onto a suitably shaped substrate. By combining rapid solidification processing with product shape control, spray forming can reduce manufacturing costs while improving product quality. De Laval nozzles offer an alternative method to the more conventional spray nozzle designs. Two applications are described: high-volume production of aluminum alloy strip, and the production of specialized tooling, such as injection molds and dies, for rapid prototyping.

Energy Technology Data Exchange (ETDEWEB)

The characteristics of solidification and melting are reviewed. The properties of water and ice and the phase diagram of water are discussed with special emphasis on ice density. A concise account of the freezing process and the Stefan problem is presented. To this end, the four stages of freezing are identified, supercooling, nucleation and the formation of dendritic ice, the growth of concentric rings of solid ice at 0{sup o}C and the final cooling of the solid ice are treated in some detail. The subject of bursting of pipes is given particular emphasis. Attention is drawn to a common misconception on pipe bursting and to misleading relationships for the computation of freezing time for ice blockage. Several current applications of melting and freezing systems are outlined. (author)

International Nuclear Information System (INIS)

The Hanford Waste Vitrification Plant Project has been established to convert the high-level radioactive waste associated with nuclear defense production at the Hanford Site into a waste form suitable for disposal in a deep geologic repository. The Hanford Waste Vitrification Plant will mix processed radioactive waste with borosilicate material, then heat the mixture to its melting point (vitrification) to forin a glass-like substance that traps the radionuclides in the glass matrix upon cooling. The Hanford Waste Vitrification Plant Quality Assurance Program has been established to support the mission of the Hanford Waste Vitrification Plant. This Quality Assurance Program Description has been written to document the Hanford Waste Vitrification Plant Quality Assurance Program.

Energy Technology Data Exchange (ETDEWEB)

In response to US Department of Energy directives, Argonne National Laboratory (ANL) has developed a waste minimization plan aimed at reducing the amount of wastes at this national research and development laboratory. Activities at ANL are primarily research- oriented and as such affect the amount and type of source reduction that can be achieved at this facility. The objective of ANL's waste minimization program is to cost-effectively reduce all types of wastes, including hazardous, mixed, radioactive, and nonhazardous wastes. The ANL Waste Minimization Plan uses a waste minimization audit as a systematic procedure to determine opportunities to reduce or eliminate waste. To facilitate these audits, a computerized bar-coding procedure is being implemented at ANL to track hazardous wastes ...

Energy Technology Data Exchange (ETDEWEB)

Results of a survey conducted by Concawe on 75 oil refineries in Europe show that the total quantity of waste requiring disposal in 1986 was 0.5 million metric tons. This quantity of waste is but 0.13% of the total refinery throughput of 387 million metric tons during 1986. The survey revealed a wide range of disposal costs, depending on the particular properties of the waste and local conditions. A summary of total waste generation and how the waste is disposed of is shown. Details on the types of waste disposed, the disposal methods used, and the costs of disposal are detailed in this excerpt from the Concawe survey.

Science.gov (United States)

This Waste Management Plan functions as a management and planning tool for managing waste streams generated as a result of operations at the Idaho CERCLA Disposal Facility (ICDF) Complex. The waste management activities described in this plan support the selected remedy presented in the Waste Area Group 3, Operable Unit 3-13 Final Record of Decision for the operation of the Idaho CERCLA Disposal Facility Complex. This plan identifies the types of waste that are anticipated during operations at the Idaho CERCLA Disposal Facility Complex. In addition, this plan presents management strategies and disposition for these anticipated waste streams.

International Nuclear Information System (INIS)

As a condition of accession into the European Union (EU), Lithuania is committed to the closure and decommissioning of Ignalina NPP comprising two RBMK-1500 reactor units (Fig. 1). It was agreed in a special protocol to the Accession Treaty that, in return for adequate EU financial assistance, Unit 1 would be closed before 2005 and Unit 2 by the end of 2009. The first unit was duly shut down on December 31, 2004. Lithuania, which has borders with Russia (Kaliningrad territory), Poland, Latvia and Belarus, spent fifty years as part of the Soviet Union and was deeply integrated into its economy and electrical infrastructure. At the break-up of the USSR, Lithuania inherited electricity generating capacity designed to supply the north-west region including ownership of Ignalina NPP located in the north-east of the country. Ignalina NPP Unit 1 was commissioned in 1983, Unit 2 in 1987; the planned lifespan of each unit was 30 years. Construction of a third unit was started but never ...

Science.gov (United States)

W. Wayne Scott, Chattanooga State Technical Institute, 4501 Amnico Highway,. Chattanooga, Tennessee 37401. Robert L. Seale, University of Arizona, Tucson, ...

Energy Technology Data Exchange (ETDEWEB)

This report documents the technical basis by which the workplace air monitoring and sampling program is operated in the 324 and 327 Buildings.

Science.gov (United States)

heat transfer augmentation was found to increase with decreasing length scale but no optimum length scale was found. Heat transfer augmentation due to turbu- ...

Science.gov (United States)

Hemez9 on the Predictive Capability Maturity Model, and for their feedback on the CAS d uring a 2 007 technical interchange meeting in Albuquerque, NM. ...

Science.gov (United States)

Procedures for a New High-Strength, Beta Titanium Alloy having. Superior Formability, " Technical Report AFML-TR-69-171, Air ...

Environmental Research Database

ObjectivesThis programme aims; To rethink how waste is thought about in social science; To provide a global analysis of waste; To examine how rethinking waste impinges on core social science concerns, notably: economies, researching globalisation, hazards and risk, and materiality. Social science understandings of waste position waste as the end-point of production and consumption, and see waste as a question of disposal.DescriptionThe Waste of the World is a five year research programme funded under ESRC's Large Grant Scheme. It brings together researchers in geography, anthropology and materials science from the University of Sheffield, Durham University, University College London and Goldsmiths College London, and connects the UK with South Asia (particularly India and Bangladesh), as well as the US, Europe and Kazakhstan. The ...

Energy Technology Data Exchange (ETDEWEB)

The applicability of the electro-slag melting method for treating plutonium contaminated metallic waste was studied. A 100kg test furnace was built and simulated metallic waste was melted and solidified in this furnace. Waste volume was reduced to 1/25 with a decontamination factor of 25 and the slag and the copper mold are repeatedly usable. The process is expected to be employed in the project of PWTF (Plutonium contaminated Waste Treatment Facilities).

Energy Technology Data Exchange (ETDEWEB)

The Waste Acceptance Preliminary Specifications (WAPS) require that the DWPF estimate the inventory of long-lived radionuclides present in the waste glass, and report the values in the Waste Form Qualification Report. In this report, conservative (biased high) estimates of the radionuclide inventory of glass produced from waste currently in the Tank Farm are provided. In most cases, these calculated values compare favorably with actual data. In those cases where the agreement is not good, the values reported here are conservative.

Energy Technology Data Exchange (ETDEWEB)

A supplementary report to the plan for waste disposal in the Copenhagen area, Denmark. It presents a mapping of wastes and waste flow in invidual areas, a description of recycling methods and waste collection systems. In addition legislative demands and potentials are dealth with. (CLS).

Energy Technology Data Exchange (ETDEWEB)

A.C.R.O. (Association pour le Controle de la Radioactivite dans l Ouest) is a French non governmental organisation that operates a laboratory for radioactivity analysis. It was created in 1986 as a response to people demands for information and reliable, independent testing. The organisation mainly carries out missions of information and training for its correspondents and more generally for a wide audience, particularly for people who worry about problems of environment, health, management of radioactive waste and emissions. Thanks to its structure, it enables citizens to involve themselves together with scientists so as to gain access to information that was hither to reserved to specialists. The organisation can vouchsafe its independence from the diversity of its members and volunteers, as well as from the diversity of its money resources. Besides its headquarters situated on the city of Caen area (Normandy), three branches situated in North Normandy, in ...

Energy Technology Data Exchange (ETDEWEB)

As nuclear research has become more prevalent, environmental contamination from the disposal of radioactive waste has become a prominent issue. At Los Alamos National Laboratory (LANL) in northern New Mexico, radioactive contamination from disposal operations has raised some very specific concerns. Material Disposal Area G (Area G) is the primary low-level radioactive waste disposal site at LANL and occupies an area adjacent to land belonging to the Native American community of the Pueblo of San Ildefonso. Analyses of soil and vegetation collected from the perimeter of Area G have shown concentrations of radionuclides greater than background concentrations established for northern New Mexico. As a result, Pueblo residents had become concerned that contaminants from Area G could enter tribal lands through various ecological pathways. The residents specifically questioned the safety of consuming meat from elk and deer that forage near Area G and ...

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing in a county by county manner the agricultural crop, agricultural wastes, municipal wastes, and industrial wastes of South Carolina that are potential biomass energy sources.

Energy Technology Data Exchange (ETDEWEB)

This report shows the probability of a catastrophic accident involving the WIPP waste hoist system. Calculations and mitigation to reduce the probability of an accident and to minimize the impact of such an accident should be included. 10 refs., 8 figs., 4 tabs.

Energy Technology Data Exchange (ETDEWEB)

Research progress is reported in 20 activities under the headings: spent fuels, defense waste management, commercial waste management, remedial action, and conventional reactors. Separate entries were prepared for each activity.

Science.gov (United States)

Quantities and compositions of non-tritium radioactive waste are estimated for some current conceptual fusion reactor designs, and disposal of large amounts of radioactive waste appears necessary. Although the initial radioactivity of fusion reactor and f...

Energy Technology Data Exchange (ETDEWEB)

This report describes mathematical predictions for the migration of radionuclides from an emplaced radioactive waste container. The model assumes a spherical-equivalent waste solid surrounded by backfill but neglects the effect of decay heat. 7 refs., 2 tabs. (TEM)

International Nuclear Information System (INIS)

To estimate the waste management needs of a fusion power reactor, a scheme for handling radioactive waste from a fusion plant has been devised. The handling scheme proceeds with radioactive waste, primarily from blanket replacement, being stored on-site; waste in cooled and shielded casks is then isolated off-site; finally, the materials are recycled. Using activities and component lifetimes supplied by designers, several conceptual fusion power reactors have been analyzed and their waste streams compared to fission reactors with regard to total activity, specific activity, and lifetimes of activity.

International Nuclear Information System (INIS)

Since 1976 the Austrian Research Centre Seibersdorf has the task to collect, treat and store radioactive waste (Radwaste) arising in Austria. Within the Department of Waste Management a variety of appropriate treatment systems are installed. For storing unconditioned and conditioned waste proper storage-halls are available. The collection of Radwaste is carried out using 100 l drums, for the conditioned waste the 200 l drum concept is used. The interim storage of conditioned waste is done at Seibersdorf until a final repository is built. The present plan foresees one to be in operation at the year 2012. (author).

Energy Technology Data Exchange (ETDEWEB)

By presenting some case studies, this paper analyzes China`s situation with regard to hazardous waste: its environmental trade, treatment, and management. The paper describes China`s experiences with the environmental trade of hazardous waste in both the internal and international market. Regulations for managing the import of waste are discussed, as are China`s major approaches to the trading of hazardous waste both at home and overseas. The major reasons for setting up the Asian-Pacific Regional Training Center for Technology Transfer and Environmental Sound Management of Wastes in China and the activities involved in this effort are also described. 1 tab.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

DC Field, Value, Language.

Science.gov (United States)

... BUCKLING ANALYSIS OF METAL MATRIX COMPOSITE SANDWICH PANELS UNDER DIFFERENT THERMAL ENVIRONMENTS , Technical Memorandum ...

Energy Technology Data Exchange (ETDEWEB)

The Savannah River Site (SRS) is a key installation for the production and research of nuclear materials for national defense and peace time applications and has been operating a full nuclear fuel cycle since the early 1950s. Wastes generated include high level radioactive, transuranic, low level radioactive, hazardous, mixed, sanitary, and aqueous wastes. Much progress has been made during the last several years to reduce these wastes including management systems, characterization, and technology programs. The reduction of wastes generated and the proper handling of the wastes have always been a part of the Site`s operation. This paper summarizes the current status and future plans with respect to waste reduction to waste reduction and reviews some specific examples of successful activities.

Energy Technology Data Exchange (ETDEWEB)

Aqueous radioactive high-level waste slurries are combined during processing steps that ultimately produce a stable borosilicate glass waste form. Chemically treated waste slurries are combined with each other and with glass frit-water slurries to produce the melter feed. Understanding the evolution of the rheological properties of the slurries is an important aspect of removing and treating the stored waste. To a first approximation, combinations of colloidal waste slurry with {approx}0.1-mm mean diameter glass frit or glass beads act in an analogous matter to slurries of spherical beads in Newtonian liquids. The non-Newtonian rheological properties of the waste slurries without frit, however, add complexity to the hydrodynamic analysis. The use of shear rate dependent apparent viscosities with the modified Einstein equation was used to model the rheological ...

Energy Technology Data Exchange (ETDEWEB)

The use of nondestructive evaluation (NDE) methods is proposed for characterization of transuranic (TRU) waste stored at the Radioactive Waste Management Complex. These NDE methods include real-time x-ray radiography, real-time neutron radiography, x-ray and neutron computed tomography, thermal imaging, container weighing, visual examination, and acoustic measurements. An integrated NDE system is proposed for characterization and certification of TRU waste destined for eventual shipment to the Waste Isolation Pilot Plant in New Mexico. Methods for automating both the classification waste and control of a complete nondestructive evaluation/nondestructive assay system are presented. Feasibility testing of the different NDE methods, including real-time x-ray radiography, and development of automated waste classification techniques are covered as part of a five year ...

Wastenet

... Waste Collection Systems Products and Equipment Find and compare a variety of waste collection systems products and equipment on the world's largest environmental industry portal. View product ...

Science.gov (United States)

Jun 16, 2011 ... Description: Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for ...

CERN Document Server

Factoring Potential Accelerator Transmutation of Waste Demonstrations into Accelerator Production of Tritium Design Planning

Energy Technology Data Exchange (ETDEWEB)

Conversion of Idaho National Engineering and Environmental Laboratory radioactive sodium-bearing waste into a single solid waste form by evaporation was demonstrated in both flask-scale and pilot-scale agitated thin film evaporator tests. A sodium-bearing waste simulant was adjusted to represent an evaporator feed in which the acid from the distillate is concentrated, neutralized, and recycled back through the evaporator. The advantage to this flowsheet is that a single remote-handled transuranic waste form is produced in the evaporator bottoms without the generation of any low-level mixed secondary waste. However, use of a recycle flowsheet in sodium-bearing waste evaporation results in a 50% increase in remote-handled transuranic volume in comparison to a non-recycle flowsheet.

Energy Technology Data Exchange (ETDEWEB)

This report is a review of waste form options for the immobilization of high-level-liquid wastes from the nuclear fuel cycle. This review covers the status of international research and development on waste forms as of May 1979. Although the emphasis in this report is on waste form properties, process parameters are discussed where they may affect final waste form properties. A summary table is provided listing properties of various nuclear waste form options. It is concluded that proposed waste forms have properties falling within a relatively narrow range. In regard to crystalline versus glass waste forms, the conclusion is that either glass of crystalline materials can be shown to have some advantage when a single property is considered; however, at this date no single waste form offers optimum ...

Energy Technology Data Exchange (ETDEWEB)

In the third quarterly report adsorption of heavy metals ions such as Cu(II) and Cr(VI) onto soils drawn from the laboratory-type wetland was shown to be weak. Secondly, it was shown that modified-clays did adsorb Cr(VI) ions strongly at pH 4.5. Further, studies on the pH dependence of the adsorption of {beta}-naphthoic acid, (NA), a well-documented contaminant in many oil and gas well waste waters onto modified-clays were undertaken and it was shown that uptake of NA by modified-clays was of the high affinity type at pH 4.5 and 7.0, but weak at pH 9.0. Adsorption of heavy metal ions, Cu{sup 2+}, and Cr(VI) onto algae, a proposed wetland amendment, was carried out and the results were presented and discussed in the fourth quarterly report. Uptake of NA by the soil component of the laboratory-type wetland was monitored as a function of pH. This quarterly report presents results from studies on the uptake of phenol and {beta}-naphthoic acid by laboratory-type ...

Energy Technology Data Exchange (ETDEWEB)

The VerTech Pit Method for wet oxidation of municipal sewage sludge offers an ecologically and economically advantageous alternative for dealing with sewage and special sludges. Europe`s first commercial plant has now been commissioned in Apeldoorn in the Netherlands following industrial-scale trials in the USA. Up to its present stage of operation the plant has achieved a high degree of reduction of solid residues and a favourable resource and environmental profile, thus impressively confirming earlier results. It is amply in keeping with the landfill criteria laid down in the Household Waste Technical Code. Furthermore, the potential sludge throughput has been found to exceed the projected value. [Deutsch] Mit dem VerTech-Tiefschachtverfahren zur Nassoxidation kommunaler Klaerschlaemme steht ein alternatives Verfahren zur Behandlung von Klaer- und Sonderschlaemmen zur Verfuegung, das oekologische und wirtschaftliche Vorteile aufweist. Nach ...

Energy Technology Data Exchange (ETDEWEB)

The Monsanto Chemical Company operates a plastics and resins plant located in Addyston, Ohio. The process equipment requires routine rinsing with technical grade acetone between batches. Due to the volumes of spent acetone generated and the associated RCRA hazardous waste regulations, the plant sought to recycle and reuse the acetone to reduce the purchase cost of virgin acetone and the cost of spent acetone disposal. One of the first options explored was package unit distillation units. The cost of these units was in the $20--$30,000 range in 1989 dollars. Even though the cost of a package unit was not deemed unreasonable, there were additional costs and concerns that led to elimination of this option. The unit would have required additional manpower to operate and maintain, i.e., at least a fraction of an operator and mechanic. For plant safety reasons, it was desired to operate this package unit outside the production building, thus ...

Energy Technology Data Exchange (ETDEWEB)

This bibliography contains abstracts relating to various aspects of ALARA program implementation and dose reduction activities, with a focus on DOE facilities. Abstracts included in this bibliography were selected from proceedings of technical meetings, journals, research reports, searches of the DOE Energy, Science and Technology Database (in general, the citation and abstract information is presented as obtained from this database), and reprints of published articles provided by the authors. Facility types and activities covered in the scope of this report include: radioactive waste, uranium enrichment, fuel fabrication, spent fuel storage and reprocessing, facility decommissioning, hot laboratories, tritium production, research, test and production reactors, weapons fabrication and testing, fusion, uranium and plutonium processing, radiography, and aocelerators. Information on improved shielding design, decontamination, containments, ...

Energy Technology Data Exchange (ETDEWEB)

During the years 1995-1999, an international effort was going on under the title DECOVALEX II, in order to study the coupled thermo-hydro-mechanical (THM) effects in the water containing fractured rock mass caused by the heat generation of spent fuel canisters in a repository. The project was a continuation project of DECOVALEX (1991-1996). The name comes from the acronym 'an international co-operative project for the DEvelopment of COupled models and their VALidation against EXperiments in nuclear waste isolation'. Radiation and Nuclear Safety Authority (STUK) was one of the eleven Funding Organizations in the international project. STUK's Research Team was the Technical Research Centre of Finland, VTT Communities and Infrastructure. To support and coordinate the national research work, STUK formed a National DECOVALEX II Group (NDG). The group had representatives from six research organisations and rock engineering ...

International Nuclear Information System (INIS)

The study area is located in the Bekaa plain of Lebanon totaling about 12753 ha. It lies between the eastern foothills of Mount Lebanon chain and expands across the Litani River towards the foothills of the eastern Anti-Lebanon Mountains. Its characteristics, i.e. natural terrain, climate and socio-economy, make it vulnerable especially due to soil pollution. This paper tries to identify the nature and level of soil pollution by heavy metals. Valley slopes represent a complex landform and lithology that contributed to the formation of different soil. Agriculture in the plain is being practiced mainly with cash, field crops and vegetables. Throughout the central part of the plain, groundwater table is abundant and relatively high (<1.0 m. locally) that multiplies the vulnerability of the soil-groundwater system. There are different sources of pollution, such as industrial (tanneries, batteries, leather manufacturing), solid and liquid wastes, and agricultural due ...

British Library Electronic Table of Contents (United Kingdom)