WorldWideScience
1

Melter system technology testing for Hanford Site low-level tankwaste vitrification  

Energy Technology Data Exchange (ETDEWEB)

Following revisions to the Tri-Party Agreement for Hanford Site cleanup, which specified vitrification for Complete melter feasibility and system operability immobilization of the low-level waste (LLW) tests, select reference melter(s), and establish reference derived from retrieval and pretreatment of the radioactive LLW glass formulation that meets complete systems defense wastes stored in 177 underground tanks, commercial requirements (June 1996). Available melter technologies were tested during 1994 to 1995 as part of a multiphase program to select reference Submit conceptual design and initiate definitive design technologies for the new LLW vitrification mission.

1996-05-03

2

Waste form development. [Hydraulic cements, hydraulic cements with additives, polymer modified gypsum cement, thermosetting polymers  

Energy Technology Data Exchange (ETDEWEB)

In this program, contemporary solidification agents are being investigated relative to their applications to major fuel cycle and non-fuel cycle low-level waste (LLW) streams. Work is being conducted to determine the range of conditions under which these solidification agents can be applied to specific LLW streams. These studies are directed primarily towards defining operating parameters for both improved solidification of problem wastes and solidification of new LLW streams generated from advanced volume reduction technologies. Work is being conducted to measure relevant waste form properties. These data will be compiled and evaluated to demonstrate compliance with waste form performance and shallow land burial acceptance criteria and transportation requirements (both as they exist and as they are modified with time). ...

1982-01-01

3

Waste form development  

International Nuclear Information System (INIS)

In this program, contemporary solidification agents are being investigated relative to their applications to major fuel cycle and non-fuel cycle low-level waste (LLW) streams. Work is being conducted to determine the range of conditions under which these solidification agents can be applied to specific LLW streams. These studies are directed primarily towards defining operating parameters for both improved solidification of problem wastes and solidification of new LLW streams generated from advanced volume reduction technologies. Work is being conducted to measure relevant waste form properties. These data will be compiled and evaluated to demonstrate compliance with waste form performance and shallow land burial acceptance criteria and transportation requirements (both as they exist and as they are modified with time). ...

1986-09-22

4

Microbial degradation of low-level radioactive waste. Final report  

Energy Technology Data Exchange (ETDEWEB)

The Nuclear Regulatory Commission stipulates in 10 CFR 61 that disposed low-level radioactive waste (LLW) be stabilized. To provide guidance to disposal vendors and nuclear station waste generators for implementing those requirements, the NRC developed the Technical Position on Waste Form, Revision 1. That document details a specified set of recommended testing procedures and criteria, including several tests for determining the biodegradation properties of waste forms. Information has been presented by a number of researchers, which indicated that those tests may be inappropriate for examining microbial degradation of cement-solidified LLW. Cement has been widely used to solidify LLW; however, the resulting waste forms are sometimes susceptible to failure due to the actions of waste constituents, ...

1996-06-01

5

Microbial degradation of low-level radioactive waste. Volume 2, Annual report for FY 1994  

Science.gov (United States)

The Nuclear Regulatory Commission stipulates in 10 CFR 61 that disposed low-level radioactive waste (LLW) be stabilized. To provide guidance to disposal vendors and nuclear station waste generators for implementing those requirements, the NRC developed the Technical Position on Waste Form, Revision 1. That document details a specified set of recommended testing procedures and criteria, including several tests for determining the biodegradation properties of waste forms. Cement has been widely used to solidify LLW; however, the resulting waste forms are sometimes susceptible to failure due to the actions of waste constituents, stress, and environment. The purpose of this research program is to develop modified microbial degradation test procedures that will be more appropriate than the existing ...

1995-08-01

6

Enhanced sludge washing evaluation plan  

Energy Technology Data Exchange (ETDEWEB)

The Tank Waste Remediation System (TWRS) Program mission is to store, treat, and immobilize highly radioactive Hanford Site waste (current and future tank waste and the strontium/cesium capsules) in an environmentally sound, safe, and cost-effective manner. The scope of the TWRS Waste Pretreatment Program is to treat tank waste and separate that waste into HLW and LLW fractions and provide additional treatment as required to feed LLW and HLW immobilization facilities. Enhanced sludge washing was chosen as the baseline process for separating Hanford tank waste sludge. Section 1.0 briefly discusses the purpose of the evaluation plan and provides the background that led to the choice of enhanced sludge washing as the baseline process. Section 2.0 provides a ...

1994-09-01

7

Low-Level waste phase 1 melter testing off gas and mass balance evaluation  

Energy Technology Data Exchange (ETDEWEB)

Commercially available melter technologies were tested during 1994-95 as part of a multiphase program to test candidate technologies for vitrification of the low-level waste (LLW) stream to be derived from retrieval and pretreatment of Hanford Site tank wastes. Seven vendors were selected for Phase 1 testing to demonstrate vitrification of a high sodium content liquid LLW simulant. The tested melter technologies included four Joule-heated melters, a carbon electrode melter, a combustion melter, and a plasma melter. Various dry and slurry melter feed preparation processes were also tested. Various feed material samples, product glass samples, and process offgas streams were characterized to provide data for evaluation of process decontamination factors and material mass balances for each vitrification technology. This report describes the melter mass balance evaluations and results ...

1996-06-28

8

The EPA (Environmental Protection Agency) low-level waste standard-a status report  

Energy Technology Data Exchange (ETDEWEB)

The Environmental Protection Agency (EPA) is developing generally applicable environmental standards for land disposal of Atomic Energy Act (AEA) low-level radioactive wastes (LLW) and certain naturally occurring and accelerator-produced radioactive material (NARM) wastes. It is EPA's intention that the LLW standards will protect public health and the environment. The LLW standards would cover disposal of all AEA materials not controlled by other EPA standards and some natural radioactive materials. Coverage of federal waste is significant, because the federal government generates and disposes of >40% of all LLW nationwide, and a uniform standard for all LLW disposal is both a desirable and an achievable goal. Publication of a proposed LLW standard is planned in 1988, and a final standard ...

1988-01-01

9

Hanford low-level waste process chemistry testing data package  

Science.gov (United States)

Recently, the Tri-Party Agreement (TPA) among the State of Washington Department of Ecology, U.S. Department of Energy (DOE) and the US Environmental Protection Agency (EPA) for the cleanup of the Hanford Site was renegotiated. The revised agreement specifies vitrification as the encapsulation technology for low level waste (LLW). A demonstration, testing, and evaluation program underway at Westinghouse Hanford Company to identify the best overall melter-system technology available for vitrification of Hanford Site LLW to meet the TPA milestones. Phase I is a {open_quotes}proof of principle{close_quotes} test to demonstrate that a melter system can process a simulated highly alkaline, high nitrate/nitrite content aqueous LLW feed into a glass product of consistent quality. Seven melter vendors were selected for the Phase I evaluation: joule-heated melters from GTS Duratek, ...

1996-03-01

10

Thermal denitration and mineralization of waste constituents  

Energy Technology Data Exchange (ETDEWEB)

In order to produce a quality grout from LLW using hydraulic cements, proper conditioning of the waste is essential for complete cement curing. Several technologies were investigated as options for conditions. Since the LLW is dilute, removal of all, or most, of the water will significantly reduce the final waste volume. Neutralization of the LLW is also desirable since acidic liquids to not allow cement to cure properly. The nitrate compounds are very soluble and easily leached from solid waste forms; therefore, denitration is desirable. Thermal and chemical denitration technologies have the advantages of water removal, neutralization, and denitration. The inclusion of additives during thermal treatment were investigated as a method of forming insoluable waste conditions.

1997-08-01

11

Long-term storage of Greater-Than-Class C Low-Level Waste  

Energy Technology Data Exchange (ETDEWEB)

Under Federal law, the Department of Energy (DOE) is responsible for safe disposal of Greater-Than-Class C Low-Level Waste (GTCC LLW) generated by licenses of the Nuclear Regulatory commission (NRC) or Agreement States. Such waste must be disposed of in a facility licensed by the NRC. It is unlikely that licensed disposal of GTCC LLW will be available prior to the year 2010. Pending availability of disposal capacity, DOE is assessing the need for collective, long-term storage of GTCC LLW. Potential risks to public health and safety caused by long-term storage of GTCC LLW at the place of generation will be evaluated to determine if alternative facilities are warranted. If warranted, several options will be investigated to determine the preferred alternative for long-term storage. These options include modification of an existing DOE facility, development of a new ...

1990-01-01

12

Methodology for assessing performance of waste management systems  

Energy Technology Data Exchange (ETDEWEB)

The purpose of the methodology provided in this report is to select the optimal way to manage particular sets of waste streams from generation to disposal in a safe and cost-effective manner. The methodology described is designed to review the entire waste management system, assess its performance, ensure that the performance objectives are met, compare different LLW management alternatives, and select the optimal alternative. The methodology is based on decision analysis approach, in which costs and risk are considered for various LLW management alternatives, a comparison of costs, risks, and benefits is made, and an optimal system is selected which minimizes costs and risks and maximizes benefits. A ''zoom-lens'' approach is suggested, i.e., one begins by looking at gross features and gradually proceeds to more and more detail. Performance assessment requires ...

1988-01-01

13

Dose consequences from a postulated criticality occurring in a low-level waste disposal facility  

Energy Technology Data Exchange (ETDEWEB)

Evaluations were done to determine conditions that could permit nuclear criticality with fissile uranium in low-level waste (LLW) facilities and to estimate potential radiation exposures to personnel if there were such an accident. Simultaneous hydrogeochemical and nuclear criticality studies were done (1) to identity realistic scenarios for uranium migration and concentration increase at LLW disposal facilities, (2) to model groundwater transport of uranium and subsequent concentration via sorption or precipitation, (3) to evaluate the potential for nuclear criticality resulting from potential increases in uranium concentration over disposal limits, and (4) to estimate potential radiation exposures to personnel resulting from criticality consequences. This paper presents the details of the radiation exposure calculations relying on the conditions as determined from the preceding studies detailed in a cited reference.

1997-12-01

14

Pathway analysis for alternate low-level waste disposal methods  

International Nuclear Information System (INIS)

The purpose of this paper is to evaluate a complete set of environmental pathways for disposal options and conditions that the Nuclear Regulatory Commission (NRC) may analyze for a low-level radioactive waste (LLW) license application. The regulations pertaining In the past, shallow-land burial has been used for the disposal of low-level radioactive waste. However, with the advent of the State Compact system of LLW disposal, many alternative technologies may be used. The alternative LLW disposal facilities include below- ground vault, tumulus, above-ground vault, shaft, and mine disposal This paper will form the foundation of an update of the previously developed Sandia National Laboratories (SNL)/NRC LLW performance assessment methodology. Based on the pathway assessment for alternative disposal methods, a determination will be made about whether the current ...

1992-03-01

15

Topical Report ''Corrosion Evaluation of LLW2 Skid-B Weld Failure Mechanisms (44139-92)  

Energy Technology Data Exchange (ETDEWEB)

An independent investigation of pipe welding leaks from the Low-Level Waste 2 (LLW2) Skid-B System for the possibilities of improper welding (IW), microbiologically influenced corrosion (MIC), sensitization, chloride pitting corrosion (CPC), and intergranular stress corrosion cracking (IGSCC) was conducted. The results show the prevailing mechanisms that caused the leaks are identified as IW, CPC, and the improper selection of weld filler material for the base metals in an environment of the North Plateau underground water. These is no evidence of MIC, sensitization, or IGSCC. The chloride pitting corrosion mechanism that took place at all the welds are also described. All the pipelines were replaced with polyvinyl chloride (PVC) for cost saving and the LLW2 Skid B System has been successfully operating since 1999. This report summarizes the findings and recommendations associated with preventive measures for future ...

2001-05-31

16

The Decommissioning of the Trino Nuclear Power Plant  

Energy Technology Data Exchange (ETDEWEB)

Following a referendum in Italy in 1987, the four Nuclear Power Plants (NPPs) owned and operated by the state utility ENEL were closed. After closing the NPPs, ENEL selected a ''safestore'' decommissioning strategy; anticipating a safestore period of some 40-50 years. This approach was consistent with the funds collected during plant operation, and was reinforced by the lack of both a waste repository and a set of national free release limits for contaminated materials in Italy. During 1999, twin decisions were made to privatize ENEL and to transform the nuclear division into a separate subsidiary of the ENEL group. This group was renamed Sogin and during the following year, ownership of the company was transferred to the Italian Treasury. On formation, Sogin was asked by the Italian government to review the national decommissioning strategy. The objective of the review was to move from a safestore strategy to a prompt ...

2002-02-27

17

Justification Of The Use Of Boreholes For Disposal Of Sealed Radiological Sources  

Energy Technology Data Exchange (ETDEWEB)

Soon there will be only 14 states in two compacts that are able to dispose of Low Level Waste (LLW): the Northwest and Rocky Mountain compact with disposal options in Richland, Washington, and the Atlantic compact with disposal options in Barnwell, South Carolina. How do states not in one of the two compacts dispose of their LLW? The Off-Site Source Recovery Project can take possession and dispose of some of the unwanted transuranic sources at the Waste Isolation Pilot Plant (WIPP). However, there will be no path forward for states outside of the two compacts for disposal of their non-transuranic LLW. A solution that has been much discussed, debated and researched, but has not been put into wide scale practice, is the borehole disposal concept. It is the author's position that companies that drill and explore for oil have been disposing of sources in borehole-like ...

2008-01-01

18

Absorption studies for selection of low cost materials for management of low level radioactive liquid waste  

International Nuclear Information System (INIS)

Natural minerals and some industrial wastes are used as low cost sorbents for removal of metal ions from effluent streams. Apatite as natural mineral and red mud as an industrial waste have been tested for their sorption properties with respect to two important fission products "1"3"7Cs and "9"0Sr. Their ion exchanging capacity was tested after every 4 hours till 24 hours. The material gets saturated after 4-8 hours. Hence these materials can be considered for treating in treating LLW before discharge, industrial waste treatment and as backfill or admixture material for shallow land repository. (author)

2010-03-01

19

Environmental Sciences Division annual progress report for period ending September 30, 1981  

Energy Technology Data Exchange (ETDEWEB)

Research programs from the following sections and programs are summarized: aquatic ecology, environmental resources, earth sciences, terrestrial ecology, advanced fossil energy program, toxic substances program, environmental impacts program, biomass, low-level waste research and development program, US DOE low-level waste management program, and waste isolation program.

1982-04-01

20

Solid Waste & Financial Assistance Program  

Science.gov (United States)

This program deals with solid waste disposal with topics/services covering: Reusable Building Materials and Large Household Items Exchange, Beneficial Use Determination, Biosolids, Certification, Compost Facil...

21

Waste reduction by separation of contaminated soils during environmental restoration  

Energy Technology Data Exchange (ETDEWEB)

During cleanup of contaminated sites, Sandia National Laboratories, New Mexico (SNL/NM) frequently encounters soils with low-level radioactive contamination. The contamination is not uniformly distributed, but occurs within areas of clean soil. Because it is difficult to characterize heterogeneously contaminated soils in detail and to excavate such soils precisely using heavy equipment, it is common for large quantities of uncontaminated soil to be removed during excavation of contaminated sites. This practice results in the commingling and disposal of clean and contaminated material as low-level waste (LLW), or possibly low-level mixed waste (LLMW). Until recently, volume reduction of radioactively contaminated soil depended on manual screening and analysis of samples, which is a costly and impractical approach and does not uphold As Low As Reasonably Achievable (ALARA) principles. To reduce the amount of ...

1998-06-01

22

A simulation of the transport and fate of radon-222 derived from thorium-230 low-level waste in the near-surface zone of the Radioactive Waste Management Site in Area 5 of the Nevada Test Site  

Energy Technology Data Exchange (ETDEWEB)

US Department of Energy (DOE) Order 5820.2A (DOE, 1988) requires performance assessments on all new and existing low-level radioactive waste (LLW) disposal sites. An integral part of performance assessment is estimating the fluxes of radioactive gases such as radon-220 and radon-222. Data needs pointed out by mathematical models drive site characterization. They provide a logical means of performing the required flux estimations. Thorium-230 waste, consisting largely of thorium hydroxide and thorium oxides, has been approved for disposal in shallow trenches and pits at the LLW Radioactive Waste Management Site in Area 5 of the Nevada Test Site. A sophisticated gas transport model, CASCADR8 (Lindstrom et al., 1992b), was used to simulate the transport and fate of radon-222 from its source of origin, nine feet below a closure cap of native soil, through the dry alluvial earth, to its ...

1993-12-01

23

Free release waste characterisation during the decommissioning of windscale Pile 2 Chimney  

International Nuclear Information System (INIS)

The decommissioning of windscale Pile 2 Chimney resulted in the removal of one of most historically significant and prominent features of the Sellafield site. The project was the first large scale concrete ''free release'' operation to be undertaken on the Sellafield nuclear site, producing 4500 tons of concrete of which 3000 tons was demonstrated to be ''free release''. The paper describes the radiometric techniques employed in the characterisation and segregation of the concrete into low level waste (LLW), very low level waste (VLLW) and free release categories. It examines the robust solutions that were developed to meet the technical and regulatory challenges of the project, which included the definition of free release, the selection of averaging volumes, the testing and validation of the monitoring systems employed for ton quantities of concrete and the identification and removal of small numbers of fuel particles ...

2002-09-22

24

EDF waste packages transport and compliance with regulations: prediction of retention of radionuclides by cementitious materials  

International Nuclear Information System (INIS)

Different concrete waste packages have been designed by Electricite de France (EDF) for the long-term storage of radioactive Low Level Waste (LLW). Their main function is to confine radionuclides from the biosphere for three hundred years in a near-surface disposal. According to the transport regulations, a Type-B package is needed for some waste like water filters. The water filters from EDF nuclear power plants are encapsulated in mortar and placed in a concrete container. Transport regulations for these containers have required the development of a methodology for safety assessment. The reference scenario of container degradation during transport considers a 9 m drop and a 800"oC fire for 30 min. First, the different chemical and physical processes involved in the containment of radionuclides are analysed. In particular, the radionuclide transport mechanisms in cement-based materials have been ...

25

Acceptable requirement of decontamination factor for LLW disposal of PEACER pyro-processing wastes  

International Nuclear Information System (INIS)

A pyrochemical process has been introduced and utilized so that the transmutation of spent PWR fuel in PEACER can produce mainly low and intermediate level waste for near surface disposal. Major radioactive nuclides from PEACER pyro-processing are composed of TRU and LLFP. In this study, the requirement for the final waste from PEACER is evaluated based on the methodology for establishment of waste acceptance criteria. Also, sensitivity analysis for several input parameters is conducted in order to determine acceptable decontamination factor (DF) and LLFP removal efficiency and to find out input parameter that extremely have an effect on DF. As a result of the study, LLFP removal efficiency, especially Sr-90 and Tc-99, is proved to be a major nuclide which contributes to annual dose by human intrusion scenario rather than TRU DF. More than 98.5% of LLFP have to be removed to meet below dose constraint within the DF more ...

2007-09-09

26

Hanford Waste Vitrification Plant Quality Assurance Program description for high-level waste form development and qualification  

International Nuclear Information System (INIS)

The Hanford Waste Vitrification Plant Project has been established to convert the high-level radioactive waste associated with nuclear defense production at the Hanford Site into a waste form suitable for disposal in a deep geologic repository. The Hanford Waste Vitrification Plant will mix processed radioactive waste with borosilicate material, then heat the mixture to its melting point (vitrification) to forin a glass-like substance that traps the radionuclides in the glass matrix upon cooling. The Hanford Waste Vitrification Plant Quality Assurance Program has been established to support the mission of the Hanford Waste Vitrification Plant. This Quality Assurance Program Description has been written to document the Hanford Waste Vitrification Plant Quality Assurance ...

1993-05-06

27

Evaluation of Phase II glass formulations for vitrification of Hanford Site low-level waste  

Energy Technology Data Exchange (ETDEWEB)

A vendor glass formulation study was carried out at Pacific Northwest Laboratory (PNL), supporting the Phase I and Phase II melter vendor testing activities for Westinghouse Hanford Company. This study is built upon the LLW glass optimization effort that will be described in a separate report. For Phase I vendor melter testing, six glass formulations were developed at PNL and additional were developed by Phase I vendors. All the doses were characterized in terms of viscosity and chemical durability by the 7-day Product Consistency Test. Twelve Phase II glass formulations (see Tables 3.5 and 3.6) were developed to accommodate 2.5 wt% P{sub 2}O{sub 5} and 1.0 wt% S0{sub 3} without significant processing problems. These levels of P{sub 2}O{sub 5} and SO{sub 3} are expected to be the highest possible concentrations from Hanford Site LLW streams at 25 wt% waste loading in glass. The Phase H compositions formulated were 6 to 23 ...

1996-03-01

28

Fiscal year 1987 program plan  

Energy Technology Data Exchange (ETDEWEB)

The Defense TRU Waste Program (DTWP) is the focal point for the Department of Energy in national planning, integration, operation, and technical development for TRU waste management. The scope of this program extends from the point of TRU waste generation through delivery to a permanent repository. The TRU program maintains a close interface with repository development to ensure program compatibility and coordination. The defense TRU program does not directly address commercial activities that generate TRU waste. Instead, it is concerned with providing alternatives to manage existing and future defense TRU wastes. The FY 87 Program Plan is consistent with the Defense TRU Waste Program goals and objectives stated in ...

1986-12-01

29

Savannah River Site Interim Waste Management Program Plan FY 1991--1992  

Energy Technology Data Exchange (ETDEWEB)

The primary purpose of the Waste Management Program Plan is to provide an annual report of how Waste Management's operations are conducted, what facilities are being used to manage wastes, what forces are acting to change current waste management systems, and what plans are in store for the coming fiscal year. In addition, this document projects activities for several years beyond the coming fiscal year in order to adequately plan for safe handling, storage, and disposal of radioactive wastes generated at the Savannah River Site and for developing technology for improved management of wastes. In this document, work descriptions and milestone schedules are current as of December 1991.

1992-05-01

30

Recommendations to the NRC for review criteria for alternative methods of low-level radioactive waste disposal: Task 2b: Earth-mounded concrete bunkers  

International Nuclear Information System (INIS)

The US Army Engineers Waterways Experiment Station (WES) and US Army Engineer Division, Huntsville (HNDED) have developed general design criteria and specific design review criteria for the earth-mounded concrete bunker (EMCB) alternative method of low-level radioactive waste (LLW) disposal. An EMCB is generally described as a reinforced concrete vault placed below grade, underneath a tumulus, surrounded by filter-blanket and drainage zones. The tumulus is covered over with a low permeability cover layer and top soil with vegetation. Eight major review criteria categories have been developed ranging from the loads imposed on the EMCB structure through material quality and durability considerations. Specific design review criteria have been developed in detail for each of the eight major categories. 63 refs., 13 figs., 2 tabs.

31

Base program on energy-related research. Quarterly report, February 1995--April 1995  

Energy Technology Data Exchange (ETDEWEB)

This report describes research performed by the Morgantown Energy Technology Center in the following areas: oil and gas; advanced systems describing a coal solid fuel and an eastern shale oil residue waste program; environmental remediation; and waste management technologies.

1995-06-01

33

ORNL nuclear waste programs annual progress report for period ending September 30, 1982  

Energy Technology Data Exchange (ETDEWEB)

Research progress is reported in 20 activities under the headings: spent fuels, defense waste management, commercial waste management, remedial action, and conventional reactors. Separate entries were prepared for each activity.

1983-05-01

34

Summary of non-US national and international radioactive waste management programs 1981  

Energy Technology Data Exchange (ETDEWEB)

Many nations and international agencies are working to develop improved technology and industrial capability for neuclear fuel cycle and waste management operations. The effort in some countries is limited to research in university laboratories on treating low-level waste from reactor plant operations. In other countries, national nuclear research institutes are engaged in major programs in all phases of the fuel cycle and waste management, and there is a national effort to commercialize fuel cycle operations. Since late 1976, staff members of Pacific Northwest Laboratory have been working under US Department of Energy sponsorship to assemble and consolidate openly available information on foreign and international nuclear waste management programs and technology. This report summarizes the information collected on the status of fuel cycle and ...

1981-06-01

35

Development and pilot demonstration program of a waste minimization plan at Argonne National Laboratory  

Energy Technology Data Exchange (ETDEWEB)

In response to US Department of Energy directives, Argonne National Laboratory (ANL) has developed a waste minimization plan aimed at reducing the amount of wastes at this national research and development laboratory. Activities at ANL are primarily research- oriented and as such affect the amount and type of source reduction that can be achieved at this facility. The objective of ANL's waste minimization program is to cost-effectively reduce all types of wastes, including hazardous, mixed, radioactive, and nonhazardous wastes. The ANL Waste Minimization Plan uses a waste minimization audit as a systematic procedure to determine opportunities to reduce or eliminate waste. To facilitate these audits, a computerized bar-coding procedure is being implemented at ANL to track hazardous ...

1991-01-01

36

Development of the Decontamination Approach for the West Valley Demonstration Project Decontamination Project Plan  

Energy Technology Data Exchange (ETDEWEB)

This paper details the development of a decontamination approach for the West Valley Demonstration Project (WVDP), Decontamination Project Plan (Plan). The WVDP is operated by West Valley Nuclear Services Company (WVNSCO), a subsidiary of Westinghouse Government and Environmental Services, and its parent companies Washington Group International and British Nuclear Fuels Limited (BNFL). The WVDP is a waste management effort being conducted by the United States Department of Energy (DOE) at the site of the only commercial nuclear fuel reprocessing facility to have operated in the United States. This facility is part of the Western New York Nuclear Service Center (WNYNSC), which is owned by the New York State Energy Research and Development Authority (NYSERDA). As authorized by Congress in 1980 through the West Valley Demonstration Project Act (WVDP Act, Public Law 96-368), the DOE's primary mission at the WVDP is to solidify high-level liquid nuclear ...

2002-02-25

37

An assessment and evaluation for recycle/reuse of contaminated process and metallurgical equipment at the DOE Rocky Flats Plant Site -- Building 865. Final report  

Energy Technology Data Exchange (ETDEWEB)

An economic analysis of the potential advantages of alternatives for recycling and reusing equipment now stored in Building 865 at the Rocky Flats Plant (RFP) in Colorado has been conducted. The inventory considered in this analysis consists primarily of metallurgical and process equipment used before January 1992, during development and production of nuclear weapons components at the site. The economic analysis consists of a thorough building inventory and cost comparisons for four equipment dispositions alternatives. The first is a baseline option of disposal at a Low Level Waste (LLW) landfill. The three alternatives investigated are metal recycling, reuse with the government sector, and release for unrestricted use. This report provides item-by-item estimates of value, disposal cost, and decontamination cost. The economic evaluation methods documented here, the simple cost comparisons presented, and the data provided as a supplement, should ...

1993-08-01

38

Modelling the work flow of a nuclear waste management program  

Energy Technology Data Exchange (ETDEWEB)

In this paper we describe a modelling project to improve a nuclear waste management program in charge of the creation of a new system for the permanent disposal of nuclear waste. SADT (Structural Analysis and Design Technique) is used in order to provide a work-flow description of the functions to be performed by the waste management program. This description is then translated into a number of Coloured Petri Nets (CPN or CP-nets) corresponding to different program functions where additional behavioural inscriptions provide basis for simulation. Each of these CP-nets is simulated to produce timed event charts that are useful for understanding the behaviour of the program functions under different scenarios. Then all the CPN models are linked together to form a single stand-alone application that is useful for validating the interaction and ...

1997-03-01

39

Defense remote-handled transuranic waste implementation plan: Transuranic Waste Program System Integration Office  

Energy Technology Data Exchange (ETDEWEB)

This document presents a detailed schedule for the implementation of the strategy for managing defense remote-handled (RH) transuranic (TRU) waste. The baseline management strategy was defined in the Defense Remote-Handled Transuranic Waste Cost/Schedule Optimization Study and is summarized in this document. Also included are revised RH TRU waste inventory projections, current site management plans, a list of key decision points and milestones, and a discussion of uncertainties associated with management of RH TRU waste. The plans are summarized in a detailed schedule diagram and in an RH TRU waste work off diagram. 9 refs., 5 figs., 4 tabs.

1988-01-01

40

Current waste-management practices and operations at Oak Ridge National Laboratory, 1982  

Energy Technology Data Exchange (ETDEWEB)

The need for efficient management of industrial chemical wastes, especially those considered hazardous or radioactive, is receiving increased attention in the United States. During the past five years, several federal laws have addressed the establishment of stronger programs for the control of hazardous and residual wastes. At a facility such as Oak Ridge National Laboratory (ORNL), an efficient waste management program is an absolute necessity to ensure protection of human health and compliance with regulatory requirements addressing the treatment and disposal of hazardous, nonhazardous, and radioactive wastes. This report highlights the major regulatory requirements under which the Laboratory must operate and their impact on ORNL facilities. Individual waste streams, estimates of quantities of waste, and current ...

1982-09-01

41

Quality assurance requirements for certification of TRU waste for shipment to the WIPP  

International Nuclear Information System (INIS)

This document presents the basic Quality Assurance (QA) requirements which shall be included in the Quality Assurance Program established by sites planning to certify Transuranic (TRU) Waste to Waste Isolation Pilot Plant (WIPP) Waste Acceptance Criteria. These QA requirements were modeled after ANSI/ASME NQA-1-1979. The application of quality assurance to Waste Certification Programs is required by WIPP-DOE-069 and DOE Order 5700.6A, as implemented by DOE Order AL 5700.6A.

42

Quality assurance requirements and description for the Civilian Radioactive Waste Management Program  

International Nuclear Information System (INIS)

The Quality Assurance Requirements and Description (QARD) is the principal quality assurance document for the Civilian Radioactive Waste Management Program (Program). It establishes the minimum requirements for the Quality Assurance Program. The QARD contains regulatory requirements and program commitments necessary for the development of an effective quality assurance program. Quality assurance implementing documents must be based on, and consistent with, QARD requirements. The QARD applies to the following: (1) acceptance of spent nuclear fuel and high-level radioactive waste; (2) transport of spent nuclear fuel and high-level radioactive waste; (3) the Monitored Retrievable Storage (MRS) facility through application for an operating license; (4) Mined Geologic Disposal System (MGDS), including the site ...

43

Framework for managing wastes from oil and gas exploration and production (E&P) sites.  

Energy Technology Data Exchange (ETDEWEB)

Oil and gas companies operate in many countries around the world. Their exploration and production (E&P) operations generate many kinds of waste that must be carefully and appropriately managed. Some of these wastes are inherently part of the E&P process; examples are drilling wastes and produced water. Other wastes are generic industrial wastes that are not unique to E&P activities, such as painting wastes and scrap metal. Still other wastes are associated with the presence of workers at the site; these include trash, food waste, and laundry wash water. In some host countries, mature environmental regulatory programs are in place that provide for various waste management options on the basis of the characteristics of the wastes and ...

2007-09-15

44

Model analysis of an inter-industrial and inter-regional waste recycling system in Japan  

Energy Technology Data Exchange (ETDEWEB)

In this study, we investigate an inter-industrial and inter-regional recycling system for industrial waste by the cement industry in Japan. We develop a linear programming model that represents cement production processes and waste transportation of all cement factories in Japan. We simulate cost and CO{sub 2}-minimizing systems. The result implies that making waste transportation more efficient in cost is an effective means for CO{sub 2} reduction. (author)

2007-04-15

45

EVALUATION OF RISKS AND WASTE CHARACTERIZATION REQUIREMENTS FOR THE TRANSURANIC WASTE EMPLACED IN WIPP DURING 1999  

Energy Technology Data Exchange (ETDEWEB)

Specifically this report: 1. Compares requirements of the WAP that are pertinent from a technical viewpoint with the WIPP pre-Permit waste characterization program, 2. Presents the results of a risk analysis of the currently emplaced wastes. Expected and bounding risks from routine operations and possible accidents are evaluated; and 3. Provides conclusions and recommendations.

2000-05-01

46

1993 Annual report on waste generation and waste minimization progress as required by DOE Order 5400.1, Hanford Site  

International Nuclear Information System (INIS)

More important than waste generation numbers, the pollution prevention and waste minimization successes achieved at Hanford in 1993 have reduced waste and improved operations at the Site. Just a few of these projects are: A small research nuclear reactor, unused and destined for disposal as low level radioactive waste, was provided to a Texas University for their nuclear research program, avoiding 25 cubic meters of waste and saving $116,000. By changing the slope on a asphalt lot in front of a waste storage pad, run-off rainwater was prevented from becoming mixed low level waste water, preventing 40 cubic meters of waste and saving $750,000. Through more efficient electrostatic paint spraying equipment and a solvent recovery system, a paint shop reduced hazardous waste by 3,500 ...

47

Strategic principles workshops: Discussion drafts and workshop notes  

Energy Technology Data Exchange (ETDEWEB)

The Office of Civilian Radioactive Waste-Management in the Department of Energy (DOE) is responsible for disposing of this nation`s spent fuel and high-level radioactive waste in a manner that protects the health and safety of the public and the quality of the environment. Although embodied in the Federal repository program that began with studies in the late 1950s, this mission was explicitly established by the Nuclear Waste Policy Act of 1982 and reaffirmed by the Nuclear Waste Policy Amendments Act of 1987. To fulfill our mission, we are developing a waste management system consisting of a geologic repository for permanent disposal deep beneath the surface of the earth, a facility for monitored retrievable storage, and a system for transporting the waste. This discussion draft was developed to help involve parties affected by or ...

1991-09-01

48

Installation Restoration Program. Stage 3. McClellan Air Force ...  

Science.gov (United States)

... pits, waste oil and solvent storage ponds (used from the 1940s to 1971), surface storage areas, settling ponds, waste water ponds, and unlined ...

1990-03-01

49

FIELD CORROSION TESTS IN REDOX AND PUREX UNDERGROUND WASTE STORAGE TANKS  

Science.gov (United States)

A corrosion-testing program has been initiated in Purex and Redox storage tnnks to obtain corrosion data on carbon steel and three associated materials in neutralized process wastes. (C.W.H.)

1955-06-28

50

Infrastructure support for a waste management institute. Final project report, September 12, 1994--September 11, 1997  

Energy Technology Data Exchange (ETDEWEB)

North Carolina A and T State University has completed the development of an infrastructure for the interdisciplinary Waste Management Institute (WMI). The Interdisciplinary Waste Management Institute (WMI) was approved in June, 1994 by the General Administration of the University of North Carolina as an academic support unit with research and public service functions. The mission of the WMI is to enhance awareness and understanding of waste management issues and to provide instructional support including research and outreach. The goals of WMI are as follows: increase the number of minority professionals who will work in waste management fields; develop cooperative and exchange programs involving faculty, students, government, and industry; serve as institutional sponsor of public awareness workshops and lecture series; and support interdisciplinary research ...

1997-11-01

51

Development and application of a gamma scanning system for LLW and MLW packages  

International Nuclear Information System (INIS)

The report describes the studies carried out to design a non-destructive system for the radiological characterization of packages containing LLW and MLW. This technique is applied for quantitative and qualitative gamma emitters determination in packages with homogeneous and heterogeneous matrices as well as the development of a maximum activity points location system. Development involves also the automatization for its industrial use.

1993-09-05

52

Waste reduction at the Savannah River Site  

Energy Technology Data Exchange (ETDEWEB)

The Savannah River Site (SRS) is a key installation for the production and research of nuclear materials for national defense and peace time applications and has been operating a full nuclear fuel cycle since the early 1950s. Wastes generated include high level radioactive, transuranic, low level radioactive, hazardous, mixed, sanitary, and aqueous wastes. Much progress has been made during the last several years to reduce these wastes including management systems, characterization, and technology programs. The reduction of wastes generated and the proper handling of the wastes have always been a part of the Site's operation. This paper summarizes the current status and future plans with respect to waste reduction to waste reduction and reviews some specific examples of successful activities.

1990-01-01

53

Waste reduction at the Savannah River Site  

Energy Technology Data Exchange (ETDEWEB)

The Savannah River Site (SRS) is a key installation for the production and research of nuclear materials for national defense and peace time applications and has been operating a full nuclear fuel cycle since the early 1950s. Wastes generated include high level radioactive, transuranic, low level radioactive, hazardous, mixed, sanitary, and aqueous wastes. Much progress has been made during the last several years to reduce these wastes including management systems, characterization, and technology programs. The reduction of wastes generated and the proper handling of the wastes have always been a part of the Site`s operation. This paper summarizes the current status and future plans with respect to waste reduction to waste reduction and reviews some specific examples of successful activities.

1990-12-31

54

SRS Public Involvement in Waste Management Has Resulted in Effective Decisions Supported by the Public Including Disposal Changes and Top-to-Bottom Review Initiative Consensus  

Science.gov (United States)

In the Savannah River Site's (SRS') Solid Waste Management Program, a key to success is the Public Involvement Program. The Solid Waste Division at SRS manages the site's transuranic, low-level, mixed, and hazardous wastes. All decisions associated with management of this waste are of interest to the public and successful program implementation would be impossible without a vigorous public involvement program. The SRS Solid Waste Division (SWD) and its Department of Energy (DOE) customer developed, implemented, and maintain a comprehensive public participation and communications program. It is staffed by public participation and technical specialists to ensure information is presented in a manner that is technically accurate while being tailored for ...

2003-02-27

55

Borehole Plugging Program  

International Nuclear Information System (INIS)

Activities are reported in programs to locate, test, and select materials for borehole plugs near nuclear waste repositories. Background information concerning borehole plugging is presented and work to date is summarized. Borehole sealants considered are listed and recommended steps to plug boreholes are given. Planned research is summarized.

56

Quality assurance requirements for high-level waste form production  

International Nuclear Information System (INIS)

The Department of Energy has issued a Quality Assurance (QA) specification for organizations involved in making a canistered high-level waste form product that is acceptable for storage in a deep geologic federal repository. The logic for the waste form acceptance process is described. In addition to NQA-1 requirements, fourteen supplemental QA requirements have been drafted to fit the waste form production process. A review plan for assuring complicance with the QA specification is provided. Guidelines for preparation of a waste form producer QA program are also presented. It is expected that the QA program description that result will be influential in supporting the acceptybility of the product to OCRWM and for ultimate disposal of the high-level waste in a deep geologic repository. (author) 3 figs., 4 refs.

57

Nuclear waste treatment program: Annual report for FY 1987  

Energy Technology Data Exchange (ETDEWEB)

Two of the US Department of Energy's (DOE) nuclear waste management-related goals are to ensure that waste management is not an obstacle to the further development of light-water reactors and the closure of the nuclear fuel cycle and to fulfill its institutional responsibility for providing safe storage and disposal of existing and future nuclear wastes. As part of its approach to achieving these goals, the Office of Remedial Action and Waste Technology of DOE established what is now called the Nuclear Waste Treatment Program (NWTP) at the Pacific Northwest Laboratory during the second half of FY 1982. To support DOE's attainment of its goals, the NWTP is to provide technology necessary for the design and operation of nuclear waste treatment facilities by commercial enterprises as part of a licensed ...

1988-09-01

58

How does one develop the right quality assurance program for waste management projects?  

International Nuclear Information System (INIS)

The quality assurance requirements in use today for radioactive waste facilities, geologic repositories and hazardous waste projects were developed initially for the nuclear power plant industry, and their intent is being applied by regulations and guidance documents to radioactive and hazardous waste programs. The wording of the NRC quality assurance requirements in Appendix B of 10CFR50, the related guidance documents and the industry's ANSI/ASME NQA-1 were developed over a period of several years to address quality assurance for the design and construction of the complex and interactive systems to produce electrical power using nuclear fuel. Now, those same documents are the basis for the quality assurance requirements and guidance for waste management facilities and repositories. The intent of Appendix B of 10CFR50 and NQA-1 can easily be applied to waste ...

1988-10-03

59

Feasibility study on the management of the disposal of Bangkok municipal waste. Final report  

Energy Technology Data Exchange (ETDEWEB)

In January, 1985, the Government of Thailand sought assistance from the United States Trade and Development Program (USTDP) to undertake a feasibility study to review and update the solid waste management master plan, with particular emphasis to be placed on waste disposal methods. In April, 1985, the USTDP engaged the firm of Engineering and Economic Research, Inc. to carry out a definitional/prefeasibility study to assess the potential of a project for solid waste management and energy production using municipal solid waste as fuel.

1989-09-01

60

Oak Ridge National Laboratory Waste Management Plan, fiscal year 1994. Revision 3  

Energy Technology Data Exchange (ETDEWEB)

US Department of Energy (DOE) Order 5820.2A was promulgated in final form on September 26, 1988. The order requires heads of field organizations to prepare and to submit updates on the waste management plans for all operations under their purview according to the format in Chap. 6, {open_quotes}Waste Management Plan Outline.{close_quotes} These plans are to be submitted by the DOE Oak Ridge Operations Office (DOE-ORO) in December of each year and distributed to the DP-12, ES&H-1, and other appropriate DOE Headquarters (DOE-HQ) organizations for review and comment. This document was prepared in response to this requirement for fiscal year (FY) 1994. The Oak Ridge National Laboratory (ORNL) waste management mission is reduction, collection, storage, treatment, and disposal of DOE wastes, generated primarily in pursuit of ORNL missions, in order to protect human health and safety and the environment. ...

1993-12-01

61

Nuclear Waste Management - A Need to Ensure that the Waste Decays While the Knowledge Does Not  

International Nuclear Information System (INIS)

The unique time scales associated with nuclear waste management require active work to preserve the knowledge associated with programs that can often span long time frames. For example, repository programs are designed and developed for the safe containment of radionuclides with half-lives on the order of 24,000 years (for Pu-239). Performance assessment studies are required to show, by predictive modeling, that these repositories can safely contain the waste for tens of thousands of years, with one million years a reality in the debate. Development of successful repository programs can span several decades. Once operational, a repository is expected to function until closure for a period of 30 to 40 years. Yet, the decision makers at all levels in such a repository program exert influence and authority over much shorter periods of time (e.g., four years for ...

62

Survey of agents and techniques applicable to the solidification of low-level radioactive wastes  

Energy Technology Data Exchange (ETDEWEB)

A review of the various solidification agents and techniques that are currently available or potentially applicable for the solidification of low-level radioactive wastes is presented. An overview of the types and quantities of low-level wastes produced is presented. Descriptions of waste form matrix materials, the wastes types for which they have been or may be applied and available information concerning relevant waste form properties and characteristics follow. Also included are descriptions of the processing techniques themselves with an emphasis on those operating parameters which impact upon waste form properties. The solidification agents considered in this survey include: hydraulic cements, thermoplastic materials, thermosetting polymers, glasses, synthetic minerals and composite materials. This survey is part of a program supported ...

1981-12-01

63

Defense Waste and Environmental Restoration Program Plan: Defense Waste Management Division  

Energy Technology Data Exchange (ETDEWEB)

The DEFENSE WASTE MANAGEMENT PROGRAM has been chartered by the Department of Energy (DOE) to receive, reduce, store, and maintain all radioactive defense waste generated by Hanford and received from offsite DOE contractors in a safe condition and in accordance with DOE and Westinghouse Hanford Company (WHC) standards. These activities are accomplished through the use of TRU retrievable storage sites, solid waste burial grounds, liquid waste storage tanks, capsule storage pools, and other low-level waste disposal methods. Continuous and/or periodic surveillance is maintained. Through the use of improved packaging methods, evaporator-crystallization and capsule production waste has been and continues to be put in a safe and economic storage condition pending future reprocessing or final disposition. For this Program Plan, ...

1988-09-01

64

Surveillance and maintenance activities of waste area groupings at Oak Ridge National Laboratory. Annual summary report for period ending September 30, 1991: Environmental Restoration Program  

Energy Technology Data Exchange (ETDEWEB)

Surveillance and maintenance (S & M) of 75 sites were conductd by the Remedial Action Section for the Environmental Restoration Program for surplus facilities and sites contaminated with radioactive materials and/or hazardous chemicals. S & M activities on these sites were conducted from the end of their operating life until final facility disposal or site stabilization. The objectives of the Waste Area Grouping S & M Program are met by maintaining a program of routine S & M as well as by implementing interim corrective maintenance when deemed necessary as a result of site surveillance. This report briefly presents this program`s activities and includes tables indicating tank levels and dry well data for FY 1991.

1991-12-01

65

Quality assurance on the Idaho National Engineering Laboratory Buried Waste Program  

International Nuclear Information System (INIS)

This paper discusses the clean-up of an Idaho National Engineering Laboratory (INEL) site utilized for disposal of transuranic contaminated waste from 1954 until 1970. The author presents requirements of the environmental protection statutes that have generated quality assurance requirements in addition to those historically implemented as a part of facility design, construction and operation. A hierarchy of program guidance quality documentation and procedures is discussed. Data qualification and computer database management are identified as requirements.

1989-04-02

66

Inventory determination of low and intermediate level radioactive waste of Paks Nuclear Power Plant origin  

International Nuclear Information System (INIS)

In the execution of disposal of low and intermediate level radioactive wastes, it is important to evaluate accurately the kind and quantity of each radionuclide in the wastes. For such an evaluation, correlation of non-gamma-emitting nuclides based on gamma-emitting nuclides is recommended and regarded as a partial method. This method necessitates a completion of a highly accurate and reliable nondestructive assay system of gamma-emitting nuclides for partical use. In 1992, in support of the new waste disposal program in Hungary, Paks NPP initiated a waste characterization program to determine the radiological properties of its rad wastes. A segmented gamma scanning system has been set up to measure the gamma-emitting nuclides in 2000 litre low level drums following in-drum compaction. In the framework of the program a ...

67

Summary of Initial Testing of SuperLig 644 at the TFL Ion Exchange Facility  

Energy Technology Data Exchange (ETDEWEB)

Research at the Savannah River Technology Center aided development of a technical design basis for a Waste Treatment Plant (WTP) to pre-treat and vitrify Hanford tank waste as part of the River Protection Project (RPP). The research addresses safety concerns, process optimization, and waste form compliance. This program will provide technical data to ensure that the process functions as it was designed and minimizes costs.

2001-04-17

68

Proceedings of the tenth annual DOE low-level waste management conference: Session 1: Institutional and regulatory issues  

Energy Technology Data Exchange (ETDEWEB)

This document contains eleven papers on various aspects of low-level radioactive waste regulation. Topics include: EPA environmental standards; international exemption principles; the concept of below regulatory concern; envirocare activities in Utah; mixed waste; FUSRAP and the Superfund; and a review of various incentive programs. Individual papers are processed separately for the data base. (TEM)

1988-12-01

69

Linking emerging hazardous waste technologies with the electronic information era  

Energy Technology Data Exchange (ETDEWEB)

In looking to the future and the development of new approaches or strategies for managing hazardous waste, it is important to understand and appreciate the factors that have contributed to current successful approaches. In the United States, several events in the last two decades have had a significant impact in advancing remediation of hazardous waste, including environmental legislation, legislative reforms on licensing federally funded research, and electronic transfer of information. Similar activities also have occurred on a global level. While each of these areas is significant, the electronic exchange of information has no national boundaries and has become an active part of major hazardous waste research and management programs. It is important to realize that any group or society that is developing a comprehensive program in hazardous waste management ...

1996-12-31

70

The review of radioactive waste management in the world  

International Nuclear Information System (INIS)

Radioactive waste is generally classified on the basis of how much radiation and the type of radiation it emits as well as the length of time over which it will continue to emit radiation. Many activities dealing with radioactive materials produce nuclear wastes, including civilian nuclear power programs (nuclear Power plant operations and nuclear fuel-cycle activities), defense nuclear programs (nuclear weapons production, naval nuclear reactor programs, and related R and D), and industrial and institutional activities (scientific research, medical operations, and other industrial uses of Radioisotopic sources or Radio chemicals). To minimize the potential adverse health and environment impacts to people and other systems including of animals, plant and etc, during the entire lifetime of the radionuclides involved, nuclear waste must be carefully and properly ...

71

National waste terminal storage program. Supplementary quality-assurance requirements  

International Nuclear Information System (INIS)

The basic Quality Assurance Program Requirements standard for the National Waste Terminal Storage Program has been developed primarily for nuclear reactors and other fairly well established nuclear facilities. In the case of waste isolation, however, there are many ongoing investigations for which quality assurance practices and requirements have not been well defined. This paper points out these problems which require supplementary requirements. Briefly these are: (1) the language barrier, that is geologists and scientists are not familiar with quality assurance (QA) terminology; (2) earth sciences deal with materials that cannot be characterized as easily as metals or other materials that are reasonably homogeneous; (3) development and control of mathematical models and associated computer programs; (4) research and development.

72

Program functionality and information analysis  

Energy Technology Data Exchange (ETDEWEB)

The Office of Civilian Radioactive Waste Management (OCRWM) is executing a plan for improvement of the United States Nuclear Waste Management Program. As part of the plan, OCRWM is performing a systems engineering analysis of both the physical system, i.e., the Nuclear Waste Management System (NWMS), and the programmatic functions that must be accomplished to bring the physical system into being. The functional analysis effort is being performed by two separate teams working in parallel, one of which addresses the physical system functions and the other the programmatic functions. This paper presents information on the analysis of the programmatic functions.

1992-04-01

73

National Low-Level Waste Management Program final summary report of key activities and accomplishments for fiscal year 1996  

Energy Technology Data Exchange (ETDEWEB)

To assist the Department of Energy (DOE) in fulfilling its responsibilities under the Low-Level Radioactive Waste Policy Amendments Act of 1985, the National Low-Level Waste Management Program (NLLWMP) outlines the key activities tat the NLLWMP will accomplish in the following fiscal year. Additional activities are added during the fiscal year as necessary to accomplish programmatic goals. This report summarizes the activities and accomplishments of the NLLWMP during Fiscal Year 1996.

1996-12-01

74

Implementation plan: Quality assurance requirements: Hazardous Waste Remedial Actions Program  

International Nuclear Information System (INIS)

This document establishes the Quality Assurance (QA) Program requirements for the Hazards Waste remedial Actions Program (HASWRAP) for ensuring, with a high degree of confidence, that program objectives will be achieved as planned. The QA Program is introduced in Sect. 1. The HAZWRAP Support Contractor Office (SCO) functional organization and QA responsibilities are shown in Sect. 2. QA program requirements are contained in Sect. 3. These requiremens are pased on the American national Standard, American National Standards Institute/American Society of Mechanical Engineers NQA-1 Quality Assurance Program Requirements for Nuclear Facilities. The 18 elements defined in the standard are tailored to HAZWRAP's needs. The QA program requirements are delineated under the major headings: Quality Assurance ...

75

FY 1987 current fiscal year work plan  

Energy Technology Data Exchange (ETDEWEB)

This Current Year Work Plan presents a detailed description of the activities to be performed by the Joint Integration Office during FY87. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance, task monitoring, information gathering and task reporting to DOE, interfacing with other agencies and DOE lead programs, ...

1986-12-01

76

Waste Sampling and Characterization Facility (WSCF). Maintenance Implementation Plan  

Energy Technology Data Exchange (ETDEWEB)

This Maintenance Implementation Plan has been developed for maintenance functions associated with the Waste Sampling and Characterization Facility (WSCF). This plan is developed from the guidelines presented by Department of Energy (DOE) Order 4330.4A, Maintenance Management Program (DOE 1990), Chapter II. The objective of this plan is to provide baseline information for establishing and identifying WHC conformance programs and policies applicable to implementation of DOE order 4330.4A guidelines. In addition, this maintenance plan identifies the actions necessary to develop a cost-effective and efficient maintenance program at WSCF.

1993-07-01

77

Statement of Work (SOW) for services provided by the Waste Sampling and Characterization Facility for the Effluent and Environmental Monitoring Program during calendar year 1998  

Energy Technology Data Exchange (ETDEWEB)

This document defines the services the Waste Sampling and Characterization Facility (WSCF) shall provide the Effluent and Environmental Monitoring Program (EEM) throughout the calendar year for analysis. The purpose of the EEM Program is to monitor liquid and gaseous effluents, and the environment immediately around the facilities which may contain radioactive and hazardous materials. Monitoring data are collected, evaluated, and reported to determine their degree of compliance with applicable federal and state regulations and permits.

1998-10-22

78

RH-TRU Waste Inventory Characterization by AK and Proposed WIPP RH-TRU Waste Characterization Objectives  

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy (DOE)-Carlsbad Field Office (CBFO) has developed draft documentation to present the proposed Waste Isolation Pilot Plant (WIPP) remote-handled (RH-) transuranic (TRU) waste characterization program to its regulators, the U.S. Environmental Protection Agency and the New Mexico Environment Department. Compliance with Title 40, Code of Federal Regulations, Parts 191 and 194; the WIPP Land Withdrawal Act (PL 102-579); and the WIPP Hazardous Waste Facility Permit, as well as the Certificates of Compliance for the 72-B and 10-160B Casks, requires that specific waste parameter limits be imposed on DOE sites disposing of TRU waste at WIPP. The DOE-CBFO must control the sites' compliance with the limits by specifying allowable characterization methods. As with the established WIPP contact handled TRU waste ...

2002-02-26

79

Hanford tanks initiative plan  

Energy Technology Data Exchange (ETDEWEB)

Abstract: The Hanford Tanks Initiative (HTI) is a five-year project resulting from the technical and financial partnership of the U.S. Department of Energy`s Office of Waste Management (EM-30) and Office of Science and Technology Development (EM-50). The HTI project accelerates activities to gain key technical, cost performance, and regulatory information on two high-level waste tanks. The HTI will provide a basis for design and regulatory decisions affecting the remainder of the Tank Waste Remediation System`s tank waste retrieval Program.

1997-07-01

80

Radioactive waste management in the USSR: A review of unclassified sources. Volume 2  

Energy Technology Data Exchange (ETDEWEB)

The Soviet Union does not currently have an overall radioactive waste management program or national laws that define objectives, procedures, and standards, although such a law is being developed, according to the Soviets. Occupational health and safety does not appear to receive major attention as it does in Western nations. In addition, construction practices that would be considered marginal in Western facilities show up in Soviet nuclear power and waste management operations. The issues involved with radioactive waste management and environmental restoration are being investigated at several large Soviet institutes; however, there is little apparent interdisciplinary integration between them, or interaction with the USSR Academy of Sciences. It is expected that a consensus on technical solutions will be achieved, but it may be slow in coming, especially for final disposal of high-level radioactive ...

1991-03-01

81

Radioactive waste management in the USSR: A review of unclassified sources  

Energy Technology Data Exchange (ETDEWEB)

The Soviet Union does not currently have an overall radioactive waste management program or national laws that define objectives, procedures, and standards, although such a law is being developed, according to the Soviets. Occupational health and safety does not appear to receive major attention as it does in Western nations. In addition, construction practices that would be considered marginal in Western facilities show up in Soviet nuclear power and waste management operations. The issues involved with radioactive waste management and environmental restoration are being investigated at several large Soviet institutes; however, there is little apparent interdisciplinary integration between them, or interaction with the USSR Academy of Sciences. It is expected that a consensus on technical solutions will be achieved, but it may be slow in coming, especially for final disposal of high-level radioactive ...

1991-03-01

82

Ocean disposal feasibility study: candidate DOE (FUSRAP) soil characterization. [Formerly Utilized Sites Remedial Action Program  

Energy Technology Data Exchange (ETDEWEB)

The Formerly Utilized Sites Remedial Action Program (FUSRAP) is to evaluate the radiological conditions at former MED-US AEC sites. Purpose of the Ocean FUSRAP program is to assess the feasibility of ocean disposal of FUSRAP waste which contains trace natural radioactive materials. This paper presents soil characterization information on the Middlesex, NJ, Sampling Plant site, and reports preliminary ocean dispersion calculations. (DLC)

1982-01-01

83

A computer program for estimating decommissioning costs for light water reactors  

Energy Technology Data Exchange (ETDEWEB)

This report discusses a desk-top computer program has been developed for estimating the costs, waste volumes, and occupational radiation exposures associated with decommissioning light-water reactor power stations. Cost categories and cost algorithms used in the program are discussed and a brief description of the user interface is given.

1993-02-01

84

Maintenance Implementation Plan for solid waste  

Energy Technology Data Exchange (ETDEWEB)

This Maintenance Implementation Plan (MIP) has been developed for. implementation of the US Department of Energy (DOE) Order 4330.4A. Maintenance Implementation Program (DOE 1990) at the Hanford Site Solid Waste complex. It addresses maintenance functions associated with Solid Waste Management, which includes the field operational group and the facilities operational group. An assessment of the existing maintenance programs for Solid Waste was performed, and the results of this assessment were evaluated to determine corrective actions required to bring Solid Waste Maintenance into compliance with the order. The MIP assessment disclosed that most elements defined in the order are currently implemented for Solid Waste. It also identified issues which must be addressed to bring the maintenance function into full compliance with DOE Order ...

1992-06-01

85

ORNL results for Test Case 1 of the International Atomic Energy Agency`s research program on the safety assessment of Near-Surface Radioactive Waste Disposal Facilities  

Energy Technology Data Exchange (ETDEWEB)

The International Atomic Energy Agency (IAEA) started the Coordinated Research Program entitled ```The Safety Assessment of Near-Surface Radioactive Waste Disposal Facilities.`` The program is aimed at improving the confidence in the modeling results for safety assessments of waste disposal facilities. The program has been given the acronym NSARS (Near-Surface Radioactive Waste Disposal Safety Assessment Reliability Study) for ease of reference. The purpose of this report is to present the ORNL modeling results for the first test case (i.e., Test Case 1) of the IAEA NSARS program. Test Case 1 is based on near-surface disposal of radionuclides that are subsequently leached to a saturated-sand aquifer. Exposure to radionuclides results from use of a well screened in the aquifer and from intrusion into the repository. Two repository concepts ...

1993-07-01

86

Sandia National Laboratories support of the Iraq Nuclear Facility Dismantlement and Disposal Program.  

Energy Technology Data Exchange (ETDEWEB)

Because of past military operations, lack of upkeep and looting there are now enormous radioactive waste problems in Iraq. These waste problems include destroyed nuclear facilities, uncharacterized radioactive wastes, liquid radioactive waste in underground tanks, wastes related to the production of yellow cake, sealed radioactive sources, activated metals and contaminated metals that must be constantly guarded. Iraq currently lacks the trained personnel, regulatory and physical infrastructure to safely and securely manage these facilities and wastes. In 2005 the International Atomic Energy Agency (IAEA) agreed to organize an international cooperative program to assist Iraq with these issues. Soon after, the Iraq Nuclear Facility Dismantlement and Disposal Program (the NDs Program) was initiated by ...

2009-03-01

87

A survey of monitoring and assay systems for release of metals from radiation controlled areas at LANL.  

Energy Technology Data Exchange (ETDEWEB)

At Los Alamos National Laboratory (LANL), a recent effort in waste minimization has focused on scrap metal from radiological controlled areas (RCAs). In particular, scrap metal from RCAs needs to be dispositioned in a reasonable and cost effective manner. Recycling of DOE scrap metals from RCAs is currently under a self-imposed moratorium. Since recycling is not available and reuse is difficult, often metal waste from RCAs, which could otherwise be recycled, is disposed of as low-level waste. Estimates at LANL put the cost of low-level waste disposal at $550 to $4000 per cubic meter, depending on the type of waste and the disposal site. If the waste is mixed, the cost for treatment and disposal can be as high as $50,000 per cubic meter. Disposal of scrap metal as low-level waste uses up valuable space in the low-level ...

2002-01-01

88

Transmutation of nuclear waste. Transmutatie van kernafval; Statusrapport programma Recyclage van Actiniden en Splijtingsprodukten (RAS)  

Energy Technology Data Exchange (ETDEWEB)

The most important aim of the title program is to investigate the possibility to convert long-lived actinides and mobile fission products in short-lived and stable isotopes by means of nuclear transmutation and recycling. First, an overview is given of the present situation regarding fission material waste, the origin of such waste in light water reactors and the options for interim and ultimate storage. Next, attention is paid to the aim of the the RAS program, the working method and the results so far of national and international research on the transmutation of actinides and fission products. Speculative expectations for the future are briefly outlined. The report also contains four appendices with technical aspects of the title subject: the RAS program of ECN, chemical aspects of reprocessing fission material, transmutation in fission reactors and in accelerators. 12 figs., 7 ...

1993-07-01

89

Technology evaluation report for the Buried Waste Robotics Program Subsurface Mapping Project  

International Nuclear Information System (INIS)

This document presents a summary of the work performed in support of the Buried Waste Robotics Program Subsurface Mapping Project. The project objective was to demonstrate the feasibility of remotely characterizing buried waste sites. To fulfill this objective, a remotely-operated vehicle, equipped with several sensors, was deployed at the Idaho National Engineering Laboratory. Descriptions of the equipment and areas involved in the project are included in this report. Additionally, this document provides data that was obtained during characterization operations at the Cold Test Pit and the Subsurface Disposal Area, both at the Idaho National Engineering Laboratory's Radioactive Waste Management Complex, and at the Idaho Chemical Processing Plant. The knowledge gained from the experience, that can be applied to the next generation remote-characterization system, is extensive and is presented in this ...

90

Detecting hot spots at hazardous-waste sites  

Energy Technology Data Exchange (ETDEWEB)

Evaluating the need for remedial cleanup at a waste site involves both finding the average contaminant concentration and identifying highly contaminated areas, or hot spots. A nomographic procedure to determine the sample configuration needed to locate a hot spot is presented. The technique can be used to develop a waste-site sampling plant - to determine either the grid spacing required to detect a hot spot at a given level of confidence, or the probability of finding a hot spot of a certain size, given a particular grid spacing. The method and computer program (ELIPGRID) were developed for locating geologic deposits, but the basic procedure can also be used to detect hot spots at chemical- or nuclear-waste disposal sites. Nomographs based on the original program are presented for three sampling-grid configurations - square, rectangular and triangular.

1984-07-09

91

UNITED STATES DEPARTMENT OF ENERGY WASTE PROCESSING ANNUAL TECHNOLOGY DEVELOPMENT REPORT 2007  

Energy Technology Data Exchange (ETDEWEB)

The Office of Environmental Management's (EM) Roadmap, U.S. Department of Energy--Office of Environmental Management Engineering & Technology Roadmap (Roadmap), defines the Department's intent to reduce the technical risk and uncertainty in its cleanup programs. The unique nature of many of the remaining facilities will require a strong and responsive engineering and technology program to improve worker and public safety, and reduce costs and environmental impacts while completing the cleanup program. The technical risks and uncertainties associated with cleanup program were identified through: (1) project risk assessments, (2) programmatic external technical reviews and technology readiness assessments, and (3) direct site input. In order to address these needs, the technical risks and uncertainties were compiled and divided into the program areas of: ...

2008-08-12

92

Local government`s pollution prevention program  

Energy Technology Data Exchange (ETDEWEB)

The pollution prevention program operated by the Health Department of Boulder County is called Business Partners for a Clean Environment (Business Partners). It is a cooperative effort among local businesses, the City of Boulder, Boulder County, and the Boulder Chamber of Commerce. This nonregulatory, incentive-based program provides industry with pollution prevention information and technical assistance necessary to reduce and/or eliminate environmental waste. This paper provides an overview of the program development, creation of partnerships and trust, and some of the results from implementation of the program. Following the first 18 months of the program, 35 businesses were recognized as Business Partners. The Business Partners program has also received an achievement award from the National Association of Counties for promoting ...

1996-12-31

93

The Los Alamos National Laboratory Environmental Restoration Program  

Energy Technology Data Exchange (ETDEWEB)

The LANL Environmental Restoration (ER) Program Office, established in October 1989, is faced with the challenge of assessing and cleaning up nearly 1,8000 potentially hazardous waste sites according to an aggressive corrective action schedule that the Environmental Protection Agency (EPA) mandated on May 23, 1990, in a Resource, Conservation, and Recovery Act (RCRA) Part B Permit. To maximize program efficiency, the ER Program Office will implement a unique management approach designed to maximize the use of laboratory technical expertise. The Installation Work Plan, which provides a blueprint for the program, has been submitted to EPA for review and approval. A work plan for characterization of Technical Area 21, an early plutonium processing facility, is also nearing completion. The feasibility of an expedited cleanup of the Laboratory's worst hazardous ...

1990-01-01

94

Using benchmarking to minimize common DOE waste streams: Volume 5. Office paper waste  

Energy Technology Data Exchange (ETDEWEB)

Finding innovative ways to reduce waste streams generated at US Department of Energy (DOE) sites by 50% by the year 2000 is a challenge for DOE`s waste minimization efforts. A team composed of members from several DOE facilities used the quality tool known as benchmarking to improve waste minimization efforts. First the team examined office waste generation and handling processes at their sites. Then team members developed telephone and written questionnaires to help identify potential ``best-in-class`` industry partners willing to share information about their best waste minimization techniques and technologies. The team identified two benchmarking partners, NIKE, Inc., in Beaverton, Oregon, and Microsoft, Inc., in Redmond, Washington. Both companies have proactive, employee-driven environmental issues programs. Both companies report strong employee ...

1995-10-01

95

Fifty years of federal radioactive waste management: Policies and practices  

Energy Technology Data Exchange (ETDEWEB)

This report provides a chronological history of policies and practices relating to the management of radioactive waste for which the US Atomic Energy Commission and its successor agencies, the Energy Research and Development Administration and the Department of Energy, have been responsible since the enactment of the Atomic Energy Act in 1946. The defense programs and capabilities that the Commission inherited in 1947 are briefly described. The Commission undertook a dramatic expansion nationwide of its physical facilities and program capabilities over the five years beginning in 1947. While the nuclear defense activities continued to be a major portion of the Atomic Energy Commission`s program, there was added in 1955 the Atoms for Peace program that spawned a multiplicity of peaceful use applications for nuclear energy, e.g., the civilian nuclear power program ...

1997-04-01

96

Surveillance and maintenance activities of waste area groupings at Oak Ridge National Laboratory  

Energy Technology Data Exchange (ETDEWEB)

Surveillance and maintenance (S M) of 75 sites were conductd by the Remedial Action Section for the Environmental Restoration Program for surplus facilities and sites contaminated with radioactive materials and/or hazardous chemicals. S M activities on these sites were conducted from the end of their operating life until final facility disposal or site stabilization. The objectives of the Waste Area Grouping S M Program are met by maintaining a program of routine S M as well as by implementing interim corrective maintenance when deemed necessary as a result of site surveillance. This report briefly presents this program's activities and includes tables indicating tank levels and dry well data for FY 1991.

1991-12-01

97

Transuranic waste form characterization and data base. Executive summary  

Energy Technology Data Exchange (ETDEWEB)

The Transuranic Waste Form Characterization and Data Base (Volume 1) provides a wide range of information from which a comprehensive data base can be established and from which standards and criteria can be developed for the present NRC waste management program. Supplementary information on each of the areas discussed in Volume 1 is presented in Appendices A through K (Volumes 2 and 3). The structure of the study (Volume 1) is outlined and appendices of Volumes 2 and 3 correlate with each main section of the report. The Executive Summary reviews the sources, quantities, characteristics and treatment of transuranic wastes in the United States. Due to the variety of potential treatment processes for transuranic wastes, the end products for long-term storage may have corresponding variations in quantities and characteristics.

1980-09-30

98

Three-dimensional assessment of the propagation and concentration distribution of waste gas from waste incinerators and sanitary landfills in built-up areas by means of specific examples. Dreidimensionale Erfassung der Ausbreitung und Konzentrationsverteilung von Abgaben aus Muellverbrennungsanlagen und Deponien in bebauten Gebieten an konkreten Beispielen  

Energy Technology Data Exchange (ETDEWEB)

Within the framework of efforts to optimize state-of-the-art waste disposal methods, this research project makes a theoretical analysis of the propagation behaviour of pollutants from landfills and waste incineration plants into the immediate vicinity of such plants. In order to judge the propagation of pollutants near the above-mentioned waste disposal facilities, a calculation program was developed within the framework of this research project which permits simulation of the propagation of such emissions in a three-dimensional space by application of an Eulerian grid model. It is capable of realistically representing fluid flow conditions and pollutant concentrations for certain points of times within the complex building patterns of such plants, for randomly chosen atmospheric conditions. (orig.)

1992-01-01

99

SLFP: A stochastic linear fractional programming approach for sustainable waste management.  

Science.gov (United States)

A stochastic linear fractional programming (SLFP) approach is developed for supporting sustainable municipal solid waste management under uncertainty. The SLFP method can solve ratio optimization problems associated with random information, where chance-constrained programming is integrated into a linear fractional programming framework. It has advantages in: (1) comparing objectives of two aspects, (2) reflecting system efficiency, (3) dealing with uncertainty expressed as probability distributions, and (4) providing optimal-ratio solutions under different system-reliability conditions. The method is applied to a case study of waste flow allocation within a municipal solid waste (MSW) management system. The obtained solutions are useful for identifying sustainable MSW management schemes with maximized system efficiency under various constraint-violation risks. ...

2011-09-01

100

Retrospective search on combustion of densified forest residues (pellets and powders) and of a agricultural wastes  

Energy Technology Data Exchange (ETDEWEB)

The combustion of forestry residues and of straw are dealt with in relation to the following: Agricultural Applications; Industrial Applications; Design; Performance and Properties; Economic Aspects; Environmental Aspects and Research programs.

1986-04-01

101

Increasing the opportunities for UK-Canada collaboration  

International Nuclear Information System (INIS)

This paper outlines the opportunities for UK-Canada collaboration/feasibility studies in areas that include novel research into waste management and decommissioning. A number of Universities in the UK have programs relevant to such collaborations in areas such as fuels; thermal hydraulics, reactor system and materials.

2007-06-03

102

Proceedings of waste stream minimization and utilization innovative concepts: An experimental technology exchange. Volume 2, Industrial liquid waste processing, industrial gaseous waste processing  

Energy Technology Data Exchange (ETDEWEB)

This two-volume proceedings summarize the results of fifteen innovations that were funded through the US Department of Energy`s Innovative Concept Program. The fifteen innovations were presented at the sixth Innovative Concepts Fair, held in Austin, Texas, on April 22--23, 1993. The concepts in this year`s fair address innovations that can substantially reduce or use waste streams. Each paper describes the need for the proposed concept, the concept being proposed, and the concept`s economics and market potential, key experimental results, and future development needs. The papers are divided into two volumes: Volume 1 addresses innovations for industrial solid waste processing and municipal waste reduction/recycling, and Volume 2 addresses industrial liquid waste processing and industrial gaseous waste processing. Individual reports are indexed separately.

1993-04-01

103

Mixed waste solidification testing on polymer and cement-based waste forms in support of Hanford`s WRAP 2A facility  

Energy Technology Data Exchange (ETDEWEB)

A testing program has been conducted by the Westinghouse Hanford Company to confirm the baseline waste form selection for use in Waste Receiving and Processing (WRAP) Module 2A. WRAP Module 2A will provide treatment required to properly dispose of containerized contact-handled, mixed low-level waste at the US Department of Energy Hanford Site in south-central Washington State. Solidification/stabilization has been chosen as the appropriate treatment for this waste. This work is intended to test cement-based, thermosetting polymer, and thermoplastic polymer solidification media to substantiate the technology approach for WRAP Module 2A. Screening tests were performed using the major chemical constituent of each waste type to measure the gross compatibility with the immobilization media and to determine formulations for more detailed testing. Surrogate materials ...

1993-10-01

104

Performance assessment overview for subseabed disposal of high level radioactive waste  

Energy Technology Data Exchange (ETDEWEB)

The Subseabed Disposal Project (SDP) was part of an international program that investigated the feasibility of high-level radioactive waste disposal in the deep ocean sediments. This report briefly describes the seven-step iterative performance assessment procedures used in this study and presents representative results of the last iteration. The results of the performance are compared to interim standards developed for the SDP, to other conceptual repositories, and to related metrics. The attributes, limitations, uncertainties, and remaining tasks in the SDP feasibility phase are discussed.

1997-06-01

106

Comprenhensive Program of Engineering and Geologic Surveys for Designing and Constructing Radioactive Waste Storage Facilities in Hard Rock Massifs  

Energy Technology Data Exchange (ETDEWEB)

Geological, geophysical, and engineering-geological research conducted at the 'Yeniseisky' site obtained data on climatic, geomorphologic, geological conditions, structure and properties of composing rock, and conditions of underground water recharge and discharge. These results provide sufficient information to make an estimate of the suitability of locating a radioactive waste (R W) underground isolation facility at the Nizhnekansky granitoid massif

2002-12-27

107

An initial survey of nuclear material safeguards requirements applicable to the civilian waste management program  

Science.gov (United States)

This report provides an initial survey of the domestic and international safeguards requirements and provides a general framework on which future studies may be based. Additional studies are needed to evaluate the activities required to implement effective safeguards within the civilian waste management system and to ensure compliance with all safeguards requirements. 16 refs.

108

Activity report 2001; Rapport annuel d'activite 2001  

Energy Technology Data Exchange (ETDEWEB)

The DED, Department of the Wastes Studies, part of the Direction of the Nuclear Energy of the CEA, regroups knowledge in the domain of the chemistry, the biochemistry, the process measures and simulation engineering applied to the radioactive wastes management. This annual report presents for the year 2001 the missions, the organization, the scientific collaborations, the research programs and the publications of the Department. (A.L.B.)

2001-07-01

109

Waste Minimization/Pollution Prevention Crosscut Plan, 1994  

International Nuclear Information System (INIS)

This plan establishes a Department-wide goal to reduce total releases of toxic chemicals to the environment and off-site transfers of such toxic chemicals by 50 percent by December 31, 1999, in compliance with Executive Order 12856. Each site that meets the threshold quantities of toxic chemicals established in the Emergency Planning and Community Right-to-Know Act (EPCRA) will participate in this goal. In addition, each DOE site will establish site-specific goals to reduce generation of hazardous, radioactive, radioactive mixed, and sanitary wastes and pollutants, as applicable. Implementation of this plan will represent a major step toward the environmental risks and costs associated with DOE operations and increasing the Department's use of preventive environmental management practices. Investing in Waste Minimization Pollution Prevention (WMin/PP) steadily reduce hazardous and radioactive waste generation and will ...

110

Wastes behavior and environmental impacts, researches and methods; Comportement des dechets et impacts environnementaux, recherches et methodes  

Energy Technology Data Exchange (ETDEWEB)

The wastes management policy takes into account more and more often the environmental impacts mastership. This evolution is particularly appreciable when the wastes directly interact with the environment: storage, utilization for roads construction and so on. In this context the ADEME organized the 8 june 2000 a colloquium to present the new evaluation methods and tools, to describe the regulations and to identify the research programs needed for this environmental policy. Eleven papers are presented. (A.L.B.)

2001-07-01

111

Electronic waste management cost: a scenario-based analysis for Greece.  

Science.gov (United States)

Waste electrical and electronic equipment (WEEE) is recognized as a priority waste stream internationally, mostly due to their volume and hazardousness. This paper presents an analysis for the quantification of WEEE management cost for Greece, taking into consideration scenarios for reverse logistics network's development and WEEE volume scenarios. Transportation cost, which represents a major cost element for any reverse logistics network, is modelled with the use of mathematical programming, targeting towards the optimization of locations for the development of required intermediate storage infrastructures. Additionally, overall operational cost and recycling fees are estimated. PMID:21242175

2011-01-17

112

Earth Sciences Division annual report 1980  

Energy Technology Data Exchange (ETDEWEB)

Summaries of the highlights of programs in the Earth Sciences Division are presented under four headings; Geosciences, Geothermal Energy Development, Nuclear Waste Isolation, and Marine Sciences. Utilizing both basic and applied research in a wide spectrum of topics, these programs are providing results that will be of value in helping to secure the nation's energy future. Separate abstracts have been prepared for each project for inclusion in the Energy Data Base. (DMC)

1981-07-01

113

Waste characterization study for the Kemp's Ridley sea turtle. Technical memo  

Energy Technology Data Exchange (ETDEWEB)

The Kemp's Ridley sea turtle, Lepidochelys kempi, is an endangered species. The National Marine Fisheries Service's Head Start program is part of an international operation to save the turtles from extinction. Under the Head Start program, eggs from the Ridley's only known wild nesting beach at Rancho Nuevo in Mexico are transported to Padre Island on the Texas coast to be hatched. The head start enables the turtles to develop a survival advantage. The principal objective was to develop baseline waste-characterization data required to design a waste-water treatment scheme for the Galveston Head Start facility. As a secondary objective, preliminary testing of some filtration components was undertaken to determine which units were most appropriate for inclusion in a wastewater treatment scheme.

1988-02-01

114

The mixed waste management facility: Cost-benefit for the Mixed Waste Management Facility at Lawrence Livermore National Laboratory  

International Nuclear Information System (INIS)

The Mixed Waste Management Facility, or MWMF, has been proposed as a national testbed facility for the demonstration and evaluation of technologies that are alternatives to incineration for the treatment of mixed low-level waste. The facility design will enable evaluation of technologies at pilot scale, including all aspects of the processes, from receiving and feed preparation to the preparation of final forms for disposal. The MWMF will reduce the risk of deploying such technologies by addressing the following: (1) Engineering development and scale-up. (2) Process integration and activation of the treatment systems. (3) Permitting and stakeholder issues. In light of the severe financial constraints imposed on the DOE and federal programs, DOE/HQ requested a study to assess the cost benefit for the MWMF given other potential alternatives to meet waste treatment needs. The MVVMF Project was asked to ...

2005-10-01

115

The Proposed Yucca Mountain Repository From A Corrosion Perspective  

Energy Technology Data Exchange (ETDEWEB)

Corrosion is a primary determinant of waste package performance at the proposed Yucca Mountain Repository and will control the delay time for radionuclide transport from the waste package. Corrosion is the most probable and most likely degradation process that will determine when packages will be penetrated and the shape, size, and distribution of those penetrations. The general issues in corrosion science, materials science and electrochemistry are well defined, and the knowledge base is substantial for understanding corrosion processes. In this paper, the Yucca Mountain Repository is viewed from a corrosion perspective. A major component of the long-term strategy for safe disposal of nuclear waste at the Yucca Mountain Repository is first to completely isolate the radionuclides in the waste packages for long times and to greatly retard the egress and transport of radionuclides from penetrated ...

2005-04-12

116

Technical considerations associated with waste-to-energy systems  

Energy Technology Data Exchange (ETDEWEB)

The average American generates four pounds of solid waste per day, yet increasing constraints are being placed on the ability of municipalities to handle waste disposal. Most cities face a scarcity of acceptable landfill sites and conventional incineration and landfill methods have come under strict air, water and soil pollution standards. City administrators are being encouraged to select from a variety of proposed technologies that supplant traditional waste disposal methods, some of which offer the promise of revenues from energy and resource recovery. The problem is to select from available near-term technologies those systems that will fit into a city's long-term solid-waste management program. Broadly, waste-to-energy recovery systems now available to cities may be classified as combustion, pyrolysis, biodegradation, and mechanical front-end ...

1981-01-01

117

Low-activity waste envelope definitions for the TWRS Privatization Phase I Request For Proposal  

Energy Technology Data Exchange (ETDEWEB)

Radioactive waste has been stored in large underground storage tanks at the Hanford Site since 1944. Approximately 212 million liters of waste containing approximately 240,000 metric tons of processed chemicals and 177 mega-curies of radionuclides are now stored in 177 tanks. These caustic wastes are in the form of liquids, slurries, saltcakes, and sludge. In 1991, the Tank Waste Remediation System (TWRS) Program was established to manage, retrieve, treat, immobilize, and dispose of these wastes in a safe, environmentally sound, and cost-effective manner. The Department of Energy (DOE) has believes that it is feasible to privatize portions of the TWRS Program. Under the privatization strategy embodied in the Request for Proposal (RFP), DOE will purchase services from a contractor-owned, contractor-operated facility under a fixed-price ...

1996-11-01

118

FY 1986 current fiscal year work plan  

Energy Technology Data Exchange (ETDEWEB)

This Current Year Work Plan presents in detail a description of the activities to be performed by the Joint Integration Office/RI during FY86. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO/RI by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO/RI tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance development, task monitoring, task progress information gathering and reporting to DOE, interfacing with other agencies and DOE lead ...

1985-11-01

119

Quality assurance considerations in nuclear waste management  

International Nuclear Information System (INIS)

Proper use of quality assurance will provide the basis for an effective management control system for nuclear waste management programs. Control is essential for achieving successful programs free from costly losses and failures and for assuring the public and regulators that the environment and health and safety are being protected. The essence of quality assurance is the conscientious use of planned and systematic actions, based on selecting and applying appropriate requirements from an established quality assurance standard. Developing a quality assurance program consists of using knowledge of the technical and managerial aspects of a project to identify and evaluate risks of loss and failure and then to select appropriate quality assurance requirements that will minimize the risks. Those requirements are integrated into the project planning documents and are carried out as specific actions during ...

120

Proceedings of the fourth annual participants' information meeting, DOE Low-Level Waste Management Program  

Energy Technology Data Exchange (ETDEWEB)

The Fourth Annual Participants' Information Meeting of the Department of Energy Low-Level Waste Management Program was held in Denver, Colorado, August 31 to September 2, 1982. The purpose of the meeting was to report and evaluate technology development funded by the program and to examine mechanisms for technology transfer. The meeting consisted of an introductory plenary session, followed by two concurrent overview sessions and then six concurrent technical sessions. There were two group meetings to review the findings of the technical sessions. The meeting concluded with a plenary summary session in which the major findings of the meeting were addressed. All papers have been abstracted and indexed for the Energy Data Base.

1982-10-01

121

Phase chemistry and radionuclide retention of high level radioactive waste tank sludges  

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy (DOE) has millions of gallons of high level nuclear waste stored in underground tanks at Hanford, Washington and Savannah River, South Carolina. These tanks will eventually be emptied and decommissioned. This will leave a residue of sludge adhering to the interior tank surfaces that may contaminate groundwaters with radionuclides and RCRA metals. Experimentation on such sludges is both dangerous and prohibitively expensive so there is a great advantage to developing artificial sludges. The US DOE Environmental Management Science Program (EMSP) has funded a program to investigate the feasibility of developing such materials. The following text reports on the success of this program, and suggests that much of the radioisotope inventory left in a tank will not move out into the surrounding environment. Ultimately, such studies may play a significant role in developing safe and ...

2000-05-19

122

Health, Safety, and Environment Division: Annual progress report 1987  

Energy Technology Data Exchange (ETDEWEB)

The primary responsibility of the Health, Safety, and Environment (HSE) Division at the Los Alamos National Laboratory is to provide comprehensive occupational health and safety programs, waste processing, and environment protection. These activities are designed to protect the worker, the public, and the environment. Many disciplines are required to meet the responsibilities, including radiation protection, industrial hygiene, safety, occupational medicine, environmental science, epidemiology, and waste management. New and challenging health and safety problems arise occasionally from the diverse research and development work of the Laboratory. Research programs in HSE Division often stem from these applied needs. These programs continue but are also extended, as needed to study specific problems for the Department of Energy and to help develop better occupational health and safety ...

1988-04-01

123

Development of the SRS environmental counting laboratory gamma spectroscopy system  

International Nuclear Information System (INIS)

The Savannah River Site (SRS), one of several U.S. Department of Energy (DOE) facilities, produces nuclear materials for national defense and for other government and civilian uses. SRS ceased production of defense materials in 1988, and the site's main activities now involve waste management and environmental restoration. These programs have generated extensive effluent monitoring and environmental surveillance programs for the Environmental Monitoring Section (EMS), which performs #approx#105,000 radiological analyses on 30,000 samples a year. Gamma spectroscopy is performed on an estimated 10,000 samples annually. This report describes a program to develop and improve the EMS system.

1996-06-16

124

Municipal solid waste management in Lebanon: the need for an integrated approach  

International Nuclear Information System (INIS)

Full text.This study focuses on the management of municipal solid waste (MSW) in Lebanon. It addresses the current status of MSW management in Lebanon in terms of collection, transport and disposal, infers the associated impacts of such practices and discusses mitigation measures and finally proposes basic guidelines for a national strategy for solid waste management in the country. The study is based on available previous investigations and on a field survey of 113 villages in four different countries. The study revealed the absence of an effective environmental policy and poor collection and disposal methods throughout the country, except for the Greater Beirut Area (G A), where better solid waste management practices are employed. Although collection of MSW outside GBA was found to be acceptable by local authorities, resources (labor and equipment) were not used efficiently. Furthermore, treatment of collected ...

2000-11-23

125

Solid waste research and development: A perspective from Pacific Northwest Laboratory  

Energy Technology Data Exchange (ETDEWEB)

The need for research and development (R&D) of technologies and approaches for sound, effective solid waste management is unquestionable. While many advances have been made by the government and private sectors, still more are needed. Resources for conducting R&D, even at the federal level, are limited however, and thus it is critical that resources be distributed as wisely as possible. The US Department of Energy has a vested interest in developing technologies and approaches for managing solid waste because solid waste management is strongly linked to energy use and environmental impacts. This federal role is needed to address the national and international impacts that can result from the cumulative effects of decisions being made at local, county, state, and regional levels. At Pacific Northwest Laboratory (PNL), one of DOE`s R&D laboratories, we are developing an integrated solid waste ...

1992-11-01

126

Joint Integration Office Independent Review Committee annual report, 1985  

Energy Technology Data Exchange (ETDEWEB)

Comprised of seven persons with extensive experience in the issues of nuclear waste, the Independent Review Committee (IRC) provides independent and objective review of Defense Transuranic Waste Program (DTWP) activities managed by the Joint Integration Office (JIO), formerly the Defense Transuranic Waste Lead Organization (TLO). The Committee is ensured a broad, interdisciplinary perspective since its membership includes representatives from the fields of nuclear engineering, nuclear waste transportation, industrial quality control, systems and environmental engineering and state and local government. The scope of IRC activities includes overall review of specific TLO plans, projects and activities, and technical review of particular research and development projects. The Committee makes specific suggestions and recommendations based upon expertise in the field of TRU ...

1986-08-01

127

Determination of vapor-liquid equilibrium data and decontamination factors needed for the development of evaporator technology for use in volume reduction of radioactive waste streams  

Energy Technology Data Exchange (ETDEWEB)

A program is currently in progress at Argonne National Laboratory to evaluate and develop evaporator technology for concentrating radioactive waste streams. By concentrating radioactive waste streams, disposal costs can be significantly reduced. To effectively reduce the volume of waste, the evaporator must achieve high decontamination factors so that the distillate is sufficiently free of radioactive material. One technology that shows a great deal of potential for this application is being developed by LICON, Inc. In this program, Argonne plans to apply LICON`s evaporator designs to the processing of radioactive solutions. Concepts that need to be incorporated into the design of the evaporator include, criticality safety, remote operation and maintenance, and materials of construction. To design an effective process for concentrating waste streams, both ...

1993-10-01

128

In Situ Remediation Integrated Program: FY 1994 program summary  

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy (DOE) established the Office of Technology Development (EM-50) as an element of the Office of Environmental Management (EM) in November 1989. In an effort to focus resources and address priority needs, EM-50 introduced the concept of integrated programs (IPs) and integrated demonstrations (IDs). The In Situ Remediation Integrated Program (ISR IP) focuses research and development on the in-place treatment of contaminated environmental media, such as soil and groundwater, and the containment of contaminants to prevent the contaminants from spreading through the environment. Using in situ remediation technologies to clean up DOE sites minimizes adverse health effects on workers and the public by reducing contact exposure. The technologies also reduce cleanup costs by orders of magnitude. This report summarizes project work conducted in FY 1994 under the ISR IP in three major areas: treatment (bioremediation), treatment ...

1995-04-01

130

The Waste Isolation Pilot Plant: A Success Story with International Cooperation  

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) administers and operates the Waste Isolation Pilot Plant (WIPP) site, which hosts a deep geologic repository for safe disposal of U.S. defense-related TRU waste and is located 42 kilometers (km) east of Carlsbad, New Mexico. CBFO also manages the National Transuranic Waste Program (NTP), which oversees TRU waste management from generation to disposal. The WIPP began receiving waste in March 1999. In some areas of broad international interest, the CBFO has developed a leading expertise through its 25-year WIPP repository and TRU waste characterization activities. In addition to participating in relevant and beneficial experiments, the CBFO will provide the international community convenient access to this information by sponsoring and hosting symposia and workshops on relevant ...

2002-02-26

131

Waste sampling and characterization facility (WSCF) maintenance implementation plan  

Energy Technology Data Exchange (ETDEWEB)

This Maintenance Implementation Plan (MIP) is written to satisfy the requirements of the US Department of Energy (DOE) Order 4330.4B, Maintenance Management Program that specifies the general policy and objectives for the establishment of the DOE controlled maintenance programs. These programs provide for the management and performance of cost effective maintenance and repair of the DOE property, which includes facilities. This document outlines maintenance activities associated with the facilities operated by Waste Management Hanford, Inc. (WMH). The objective of this MIP is to provide baseline information for the control and execution of WMH Facility Maintenance activities relative to the requirements of Order 4330.4B, assessment of the WMH maintenance programs, and actions necessary to maintain compliance with the Order. Section 2.0 summarizes the history, mission and description ...

1997-08-13

132

Risk perception on management of nuclear high-level and transuranic waste storage  

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy`s program for disposing of nuclear High-Level Waste (HLW) and transuranic (TRU) waste has been impeded by overwhelming political opposition fueled by public perceptions of actual risk. Analysis of these perceptions shows them to be deeply rooted in images of fear and dread that have been present since the discovery of radioactivity. The development and use of nuclear weapons linked these images to reality and the mishandling of radioactive waste from the nations military weapons facilities has contributed toward creating a state of distrust that cannot be erased quickly or easily. In addition, the analysis indicates that even the highly educated technical community is not well informed on the latest technology involved with nuclear HLW and TRU waste disposal. It is not surprising then, that the general public feels uncomfortable with DOE`s management plans ...

1994-08-15

133

Laboratory for characterization of spent nuclear fuel and high/medium level radioactive waste. Experimental results and performances  

International Nuclear Information System (INIS)

During the phases of separation, treatment, conditioning and storage of radioactive waste, destructive and nondestructive methods for their characterization are needed. In order to satisfy this necessity, in the frame of the National Program of Research and Development, the 'Laboratory for characterization of spent nuclear fuel and high/medium level radioactive waste- LABORAD' was created. The purpose of the project was to accredit the analysis methods available in the laboratory, and also to develop new methods for the characterization of the radioactive waste. A special attention was paid to the high-level radioactive waste and spent nuclear fuel characterization that require special facilities for handling. These facilities (e.g. hot cells, remote handlers, transport container) are already available in our institute. Experimental results and performances obtained during ...

2009-05-27

134

Annual report on monitoring of the unsaturated zone and recharge areas at INEL to the state of Idaho INEL Oversight Committee  

Energy Technology Data Exchange (ETDEWEB)

During the early years of the INEL, the USGS conducted extensive studies (sitewide drilling program) of the geology and hydrology of the area collecting varied data over the years. The unsaturated zone has not received much attention until recently. The studies that have been done are a result of problems or concerns arising from liquid radioactive waste disposal. The TRA facility has the most information published about its waste disposal activities. The ICPP has less data about the unsaturated zone due to the fact that most waste water disposal has been to a well. Little is known about the effect of waste water disposal at the NRF on the unsaturated zone. Essentially no information was found about waste disposal activities at other facilities, primarily because there does not appear to be any reported problems associated with waste water ...

1992-01-01

135

Annual report on monitoring of the unsaturated zone and recharge areas at INEL to the state of Idaho INEL Oversight Committee  

Energy Technology Data Exchange (ETDEWEB)

During the early years of the INEL, the USGS conducted extensive studies (sitewide drilling program) of the geology and hydrology of the area collecting varied data over the years. The unsaturated zone has not received much attention until recently. The studies that have been done are a result of problems or concerns arising from liquid radioactive waste disposal. The TRA facility has the most information published about its waste disposal activities. The ICPP has less data about the unsaturated zone due to the fact that most waste water disposal has been to a well. Little is known about the effect of waste water disposal at the NRF on the unsaturated zone. Essentially no information was found about waste disposal activities at other facilities, primarily because there does not appear to be any reported problems associated with waste water ...

1992-12-31

136

Advanced organic analysis and analytical methods development: FY 1995 progress report. Waste Tank Organic Safety Program  

Energy Technology Data Exchange (ETDEWEB)

This report describes the work performed during FY 1995 by Pacific Northwest Laboratory in developing and optimizing analysis techniques for identifying organics present in Hanford waste tanks. The main focus was to provide a means for rapidly obtaining the most useful information concerning the organics present in tank waste, with minimal sample handling and with minimal waste generation. One major focus has been to optimize analytical methods for organic speciation. Select methods, such as atmospheric pressure chemical ionization mass spectrometry and matrix-assisted laser desorption/ionization mass spectrometry, were developed to increase the speciation capabilities, while minimizing sample handling. A capillary electrophoresis method was developed to improve separation capabilities while minimizing additional waste generation. In addition, considerable emphasis has been placed on developing a rapid ...

1995-09-01

137

Update of the management strategy for Oak Ridge National Laboratory Liquid Low-Level Waste  

Energy Technology Data Exchange (ETDEWEB)

The strategy for management of the Oak Ridge National Laboratory`s (ORNL) radioactively contaminated liquid waste was reviewed in 1991. The latest information available through the end of 1990 on waste characterization, regulations, US Department of Energy (DOE) budget guidance, and research and development programs was evaluated to determine how the strategy should be revised. Few changes are needed to update the strategy to reflect new waste characterization, research, and regulatory information. However, recent budget guidance from DOE indicates that minimum funding will not be sufficient to accomplish original objectives to upgrade the liquid low-level waste (LLLW) system to comply with the Federal Facilities Agreement, provide long-term LLLW treatment capability, and minimize environmental, safety, and health risks. Options are presented that might allow the ORNL LLLW system to ...

1995-04-01

138

Status of the ORNL liquid low-level waste management upgrades  

Energy Technology Data Exchange (ETDEWEB)

The strategy for management of the Oak Ridge National Laboratory`s (ORNL`s) radioactively contaminated liquid waste was reviewed. The latest information on waste characterization, regulations, US Department of Energy (DOE) budget guidance, and research and development programs was evaluated to determine how the strategy should be revised. Few changes are needed to update the strategy to reflect new waste characterization, research, and regulatory information. However, recent budget guidance from DOE indicates that minimum funding will not be sufficient to accomplish original objectives to upgrade the liquid low-level waste (LLLW) system to be in compliance with the Federal Facilities Agreement compliance, provide long-term LLLW treatment capability, and minimize Environmental Safety & Health risks. Options are presented that might allow the ORNL LLLW system to continue ...

1995-08-01

139

Final environmental impact statement. Waste Isolation Pilot Plant  

Energy Technology Data Exchange (ETDEWEB)

In accordance with the National Environmental Policy Act (NEPA) of 1969, the US Department of Energy (DOE) has prepared this document as environmental input to future decisions regarding the Waste Isolation Pilot Plant (WIPP), which would include the disposal of transuranic waste, as currently authorized. The alternatives covered in this document are the following: (1) Continue storing transuranic (TRU) waste at the Idaho National Engineering Laboratory (INEL) as it is now or with improved confinement. (2) Proceed with WIPP at the Los Medanos site in southeastern New Mexico, as currently authorized. (3) Dispose of TRU waste in the first available repository for high-level waste. The Los Medanos site would be investigated for its potential suitability as a candidate site. This is administration policy and is the alternative preferred by the DOE. (4) Delay the WIPP to allow other ...

1980-10-01

140

Overview of the FRG waste package materials corrosion test program  

International Nuclear Information System (INIS)

Presently in the FRG there are essentially three institutions involved in corrosion experiments related to high level waste package materials, namely KfK-INE, Nukem and Bayer Leverkusen. In 1981 KfK-INE started a corrosion test program aiming at the selection of suitable canister materials for vitrified high level waste. The program encompassed electrochemical investigations, which were concluded in 1984. Moreover field corrosion tests and laboratory experiments were initiated, and are still ongoing. Several possible canister materials such as mild steel, Ti-Pd-alloy, Hastelloy C4 and others were investigated under the influence of varying parameters such as temperature, and radiation. Both Nukem Company and DWK were assigned the responsibility to conceive and develop a cask for the direct final disposal of spent fuel assemblies. Two solution turned out as most promising for corrosion protection of ...

1988-03-08

141
142

Structural acceptance criteria for the evaulation of existing double-shell waste storage tanks located at the Hanford site, Richland, Washington  

Energy Technology Data Exchange (ETDEWEB)

The structural acceptance criteria contained herein for the evaluation of existing underground double-shell waste storage tanks located at the Hanford Site is part of the Life Management/Aging Management Program of the Tank Waste Remediation System. The purpose of the overall life management program is to ensure that confinement of the waste is maintained over the required service life of the tanks. Characterization of the present condition of the tanks, understanding and characterization of potential degradation mechanisms, and development of tank structural acceptance criteria based on previous service and projected use are prerequisites to assessing tank integrity, to projecting the length of tank service, and to developing and applying prudent fixes or repairs. The criteria provided herein summarize the requirements for the analysis and structural qualification of the existing ...

1995-09-01

143

Salt repository project closeout status report  

Energy Technology Data Exchange (ETDEWEB)

This report provides an overview of the scope and status of the US Department of Energy (DOE`s) Salt Repository Project (SRP) at the time when the project was terminated by the Nuclear Waste Policy Amendments Act of 1987. The report reviews the 10-year program of siting a geologic repository for high-level nuclear waste in rock salt formations. Its purpose is to aid persons interested in the information developed during the course of this effort. Each area is briefly described and the major items of information are noted. This report, the three salt Environmental Assessments, and the Site Characterization Plan are the suggested starting points for any search of the literature and information developed by the program participants. Prior to termination, DOE was preparing to characterize three candidate sites for the first mined geologic repository for the permanent disposal of high-level nuclear ...

1988-06-01

144

Review of the Vortec soil remediation demonstration program  

Energy Technology Data Exchange (ETDEWEB)

The DOE`s clean-up of its nuclear complex require the development of innovative technologies to convert soils contaminated by hazardous and/or radioactive wastes to forms which can be readily disposed in accordance with current waste disposal methods. The unique features of Votec CMS technology should make it particularly cost-effective process for the vitrification of soils, sediments, sludges, and mill tailings containing organic metallic and/or radioactive contaminants. This article describes the technology (Votec`s combustion and melting system), the results of testing, the demonstration plant system, and summarizes the future schedule and the equipment needed. 3 figs., 3 tabs.

1994-11-01

145

Pyro-chemistry within the FP7 ACSEPT Project-Program and Objective  

Energy Technology Data Exchange (ETDEWEB)

Actinide recycling by partitioning and transmutation is considered as one of the most promising strategies to reduce the inventory of radioactive waste, thus contributing to make nuclear energy sustainable. To make advances beyond the current state of the art in pyrochemical separations processes, the Domain 2 (DM2) of ACSEPT has been built on considering a process approach based on system studied. Four work packages that represent the main steps of a process block diagram have been identified: head-end steps, core process development, and salt treatment for recycling and waste conditioning. The results obtained in this domain will be integrated in DM 3 (Process) in order to orientate the R and D studies of DM2 and to propose and validate flowsheets at the end of the project. The state of the art on pyrochemical separation within the European Community and the working program of ACSEPT in pyrometallurgy are presented in ...

2008-07-01

146

Ten-year cleanup of U.S. Department of Energy weapon sites: The changing roles for technology development in an era of privatization  

Energy Technology Data Exchange (ETDEWEB)

In its beginning, the U.S. Department of Energy (DOE) Office of Environmental Management (EM) viewed private industry as lacking adequate technology know-how to meet demands of hazardous and radioactive waste problems at the DOE`s laboratories and nuclear weapons production facilities. In November 1989, EM`s Office of Technology Development (recently renamed the Office of Science and Technology) embarked on a bold program of developing and demonstrating {open_quotes}innovative{close_quotes} waste cleanup technologies that would be safer, faster, more effective, and less expensive than the {open_quotes}baseline{close_quotes} commercial methods. This program has engaged DOE sites, national laboratories, and universities to produce preferred solutions to the problems of handling and treating DOE wastes. More recently, much of this work has shifted to joint efforts with private industry ...

1996-12-31

147

Separation science and technology. Semiannual progress report, April 1992--September 1992  

Energy Technology Data Exchange (ETDEWEB)

This document reports on the work done by the Separations Science and Technology Programs of the Chemical Technology Division, Argonne National Laboratory, in the period April-September 1992. This effort is mainly concerned with developing the TRUEX process for removing and concentrating actinides from acidic waste streams contaminated with transuranic (TRU) elements. The objectives of TRUEX processing are to recover valuable TRU elements and to lower disposal costs for the nonTRU waste product of the process. Two other projects are underway with the objective of developing (1) a membrane-assisted solvent extraction method for treating natural and process waters contaminated by volatile organic compounds and (2) evaporation technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process.

1994-09-01

148

RADIONUCLIDE DATA PACKAGE FOR PERFORMANCE ASSESSMENT CALCULATIONS RELATED TO THE E-AREA LOW-LEVEL WASTE FACILITY AT THE SAVANNAH RIVER SITE.  

Energy Technology Data Exchange (ETDEWEB)

The Savannah River Site disposes of low-level radioactive waste within on-site engineered disposal facilities. The Savannah River Site must demonstrate that these disposals meet the requirements of DOE Order 435 . 1 through a process known as performance assessment (PA). The objective of this document is to provide the radionuclide -specific data needed for the PA calculations . This work is part of an on-going program to periodically review and update existing PA work as new data becomes available. Revision of the E -Area Low-Level Waste Facility PA is currently underway. The number of radionuclides selected to undergo detailed analysis in the PA is determined by a screening process. The basis of this process is described. Radionuclide-specific data for half-lives, decay modes, daughters, dose conversion factors and groundwater concentration limits are presented with source references and methodologies.

2007-03-20

149

A two-stage support-vector-regression optimization model for municipal solid waste management - A case study of Beijing, China  

British Library Electronic Table of Contents (United Kingdom)

In this study, a two-stage support-vector-regression optimization model (TSOM) is developed for the planning of municipal solid waste (MSW) management in the urban districts of Beijing, China. It represents a new effort to enhance the analysis accuracy in optimizing the MSW management system through coupling the support-vector-regression (SVR) model with an interval-parameter mixed integer linear programming (IMILP). The developed TSOM can not only predict the city's future waste generation amount, but also reflect dynamic, interactive, and uncertain characteristics of the MSW management system. Four kernel functions such as linear kernel, polynomial kernel, radial basis function, and multi-layer perception kernel are chosen based on three quantitative simulation performance criteria [i.e....

2011-01-01

150

Waste Handeling Building Conceptual Study  

Energy Technology Data Exchange (ETDEWEB)

The objective of the ''Waste Handling Building Conceptual Study'' is to develop proposed design requirements for the repository Waste Handling System in sufficient detail to allow the surface facility design to proceed to the License Application effort if the proposed requirements are approved by DOE. Proposed requirements were developed to further refine waste handling facility performance characteristics and design constraints with an emphasis on supporting modular construction, minimizing fuel inventory, and optimizing facility maintainability and dry handling operations. To meet this objective, this study attempts to provide an alternative design to the Site Recommendation design that is flexible, simple, reliable, and can be constructed in phases. The design concept will be input to the ''Modular Design/Construction and Operation Options Report'', ...

2000-11-06

151

Separation Science and Technology. Semiannual progress report, April 1993--September 1993  

Energy Technology Data Exchange (ETDEWEB)

This document reports on the work done by the Separations Science and Technology Programs of the Chemical Technology Division, Argonne National Laboratory, in the period April-September 1993. This effort is mainly concerned with developing the TRUEX process for removing and concentrating actinides from acidic waste streams contaminated with transuranic (TRU) elements. The objectives of TRUEX processing are to recover valuable TRU elements and to lower disposal costs for the nonTRU waste product of the process. Other projects are underway with the objective of developing (1) evaporation technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process, (2) treatment schemes for liquid wastes stored or being generated at Argonne, (3) a process based on sorbing modified TRUEX solvent on magnetic beads to be used for separation of ...

1996-01-01

152

Regional integrated solid waste management: an optimization model for northern Lebanon  

International Nuclear Information System (INIS)

Full text.Increased environmental concerns and the emphasis on material and energy recovery are gradually changing the orientation of municipal solid waste (MSW) management and planning. In this context, the application of optimization techniques have been introduced to design the least cost solid waste management systems, considering the variety of management processes (recycling, composting, anaerobic digestion, incineration and land filling) and the existence of uncertainties associated with the number of system components and their interrelations. This study presents a model that was developed and applied to serve as a solid socio-economic and environmental considerations. The model accounts for solid waste generation rates, composition, collection, treatment, disposal as well as potential environmental impacts of various MSW management techniques. The model follows a linear programming formulation ...

2000-11-23

153

Quality assurance requirements for high-level waste form production  

International Nuclear Information System (INIS)

The US Department of Energy (DOE) Defense Waste Management Plan has the objective of final disposal for high-level waste (HLW) generated from defense programs. The DOE sites that generate HLW are located at the Savannah River Operations Office in Aiken, South Carolina, the Hanford site in Richland, Washington, and the Idaho Operations Office in Idaho Falls, Idaho. The purpose in the development of a quality assurance (QA) specification for organizations involved in HLW production is to establish uniform requirements that ensure that radioactive waste is converted to a waste form and canistered in such a way that it is acceptable in a federal repository licensed by the US Nuclear Regulatory Commission (NRC). A QA specification has been developed that will be applied to those activities important to certification of the product. The basic requirements are defined in national consensus ...

1988-06-12

154

Composites from recycled wood and plastics. Report for May 1990-July 1993  

Energy Technology Data Exchange (ETDEWEB)

The ultimate goal of this research was to develop technology to convert recycled wood fiber and plastics into durable products that are recyclable and otherwise environmentally friendly. Two processing technologies were used to prepare wood-plastic composites: air-laying and melt-blending. Research was conducted in (1) developing laboratory methods for converting waste wood, wastepaper, and waste plastics into forms suitable for processing into composites; (2) optimizing laboratory methods for making composite panels from the waste materials; (3) establishing a database on the effects of formulation and bonding agent on physical and mechanical properties of composites; (4) establishing the extent to which the composites can be recycled without unacceptable loss in properties; and (5) reaching out to industry to provide education, to develop applications, and to extend the database. Overall, the program ...

1995-01-01

155

Cleanup at Los Alamos National Laboratory - the challenges - 9493  

Energy Technology Data Exchange (ETDEWEB)

This paper provides an overview of environmental cleanup at the Los Alamos National Laboratory (LANL) and some of the unique aspects and challenges. Cleanup of the 65-year old Department of Energy Laboratory is being conducted under a RCRA Consent Order with the State of New Mexico. This agreement is one of the most recent cleanup agreements signed in the DOE complex and was based on lessons learned at other DOE sites. A number of attributes create unique challenges for LANL cleanup -- the proximity to the community and pueblos, the site's topography and geology, and the nature of LANL's on-going missions. This overview paper will set the stage for other papers in this session, including papers that present: Plans to retrieve buried waste at Material Disposal Area B, across the street from oen of Los Alamos' commercial districts and the local newspaper; Progress to date and joint plans with WIPP for disposal of the remaining inventory of ...

2008-01-01

156

Adsorption/Membrane Filtration as a Contaminant Concentration and Separation Process for Mixed Wastes and Tank Wastes - Final Report  

Energy Technology Data Exchange (ETDEWEB)

This project was conducted to evaluate novel approaches for removing radioactive strontium (Sr) and cesium (Cs) from the tank wastes. The bulk of the Sr removal research conducted as part of this project investigated adsorption of Sr onto a novel adsorbent known as iron-oxide-coated sand. The second major focus of the work was on the removal of cesium. Since the chemistries of strontium and cesium have little commonality, different materials (namely, cesium scavengers known as hexacyanoferrates, HCFs) were employed in these tests. This study bridged several scientific areas and yielded valuable knowledge for implementing new technological processes. The applicability of the results extends beyond the highly specialized application niches investigated experimentally to other issues of potential interest for EMSP programs (e.g., separation of chromium from a variety of wastes using IOCS, separation of Cs from neutral and ...

1999-10-01

157

Ocean FUSRAP: Feasibility of ocean disposal of materials from the Formerly Utilized Sites Remedial Action Program (FUSRAP)  

International Nuclear Information System (INIS)

The purpose of the Ocean FUSRAP Program, which began in March 1981, is to assess the technical, environmental, and institutional feasibility of disposing, in the ocean and on the ocean floor, of FUSRAP waste which contains traces of natural radioactive materials. The initial planning has focused on the Middlesex, New Jersey, Sampling Plant site and surrounding properties, which contain on the order of 100,000 metric tons of material. The Belgian Congo uranium ore and other uranium ores used by the United States were handled at the sampling plant site and have since been removed.

158

Inland wetlands legislation and management. January 1970-September 1989 (Citations from the NTIS data base). Report for January 1970-September 1989  

Energy Technology Data Exchange (ETDEWEB)

This bibliography contains citations concerning Federal and state laws and management programs for the protection and use of inland wetlands. Utilization of wetlands to control highway runoff and community waste water is discussed. Wetlands protection programs, restoration projects, resource planning, and wetlands identification methods are cited. References to coastal and salt-water wetlands are excluded from this bibliography. (This updated bibliography contains 219 citations, 37 of which are new entries to the previous edition.)

1989-10-01

159

Argonne National Laboratory-East evolution of solid waste management  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this report is to provide the reader with a basic understanding of Argonne National Laboratory`s current general refuse disposal and material recycling programs, how they were developed, and where they are going. In order to better understand the current situation, a brief description of the facilities past practices is explained. ANL is a multi-program research and development center owned by DOE and operated by the University of Chicago. Argonne`s primary facilities are on a 1,700 acre site, 27 miles southwest of Chicago. Fifty-seven major buildings house approximately 4,500 employees at the site.

1996-07-01

160

A decade of waste and pollution management  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this report is to provide the reader with a basic understanding of Argonne National Laboratory`s current general refuse disposal and material recycling programs, how they were developed, and where they are going. In order to better understand the current situation, a brief description of the facilities past practices is explained. ANL is a multi-program research and development center owned by the U.S. Department of Energy (DOE) and operated by the University of Chicago. Argonne`s primary facilities are on a 1,700 acre site, 27 miles southwest of Chicago. Fifty-seven major buildings house approximately 4,500 employees at the site.

1996-10-01

161

HAMMER FY 1996 Multi-Year Program Plan: WBS {number_sign}8.2  

Energy Technology Data Exchange (ETDEWEB)

The Hazardous Material Management and Emergency Response Training and Education Center -- known simply as HAMMER -- is being developed to assist the US Department of Energy (DOE) and others dedicated to improving worker health, safety and productivity. HAMMER is a training and education program for hazardous material, waste management, and emergency response workers. HAMMER is managed by the DOE Richland Operations Office under Work Breakdown Structure (8.2). The 1996 Multi-Year Program Plan (MYPP) includes the Execution Year data and provides the information for Programmatic Fiscal Year Site Management System Execution Baseline, as well as the detailed work plan for performance evaluation of the authorized work. The MYPP incorporates various planning methodologies to define the program and provides essential program integration, and a fully developed technical, cost, and schedule ...

1995-09-01

162

Uranium-233 waste definition: Disposal options, safeguards, criticality control, and arms control  

Energy Technology Data Exchange (ETDEWEB)

The US investigated the use of {sup 233}U for weapons, reactors, and other purposes from the 1950s into the 1970s. Based on the results of these investigations, it was decided not to use {sup 233}U on a large scale. Most of the {sup 233}U-containing materials were placed in long-term storage. At the end of the cold war, the US initiated, as part of its arms control policies, a disposition program for excess fissile materials. Other programs were accelerated for disposal of radioactive wastes placed in storage during the cold war. Last, potential safety issues were identified related to the storage of some {sup 233}U-containing materials. Because of these changes, significant activities associated with {sup 233}U-containing materials are expected. This report is one of a series of reports to provide the technical bases for future decisions on how to manage this material. A basis for defining when {sup 233}U-containing ...

1998-07-07

163

U. S. Navy shipboard-generated plastic-waste pilot-recycling program. Research and development report, Apr 90-Jan 91  

Energy Technology Data Exchange (ETDEWEB)

From April 1990 through January 1991, the feasibility of recycling Navy shipboard-generated plastic wastes was explored. Normally, plastic wastes are source separated aboard Navy ships and retained for shoreside disposal in accordance with new fleet requirements implementing MARPOL Annex V that prohibits the discharge of plastics at sea. Over 23,000 pounds of shipboard plastic wastes from USS Lexington (AVT 16) and ships from the Norfolk Naval Base were recycled into park benches, picnic tables and carstops that have been distributed back to the Navy bases for use. Navy shipboard plastics must undergo sorting prior to recycling because Navy plastic waste contains large quantities of composite plastic items (e.g., plastic/paper) that are not easily recyclable. Recycling food-contaminated plastics is not practical due to sanitation problems encountered during handling. However, certain items have good ...

1991-03-01

164

Environmental Science and Research Foundation annual technical report to DOE-ID, January , 1995--December 31, 1995  

International Nuclear Information System (INIS)

The foundation conducts an environmental monitoring and surveillance program over an area covering much of the upper Snake River Plain and provide environmental education and support services related to INEL natural resource issues. Also, the foundation, with its university affiliates, conducts ecological and radioecological research on the Idaho National Environmental Research Park. This research benefits major DOE-ID programs including waste management, environmental restoration, spent nuclear fuels, and land management issues. Major accomplishments during CY1995 can be divided into five categories: environmental surveillance program, environmental education, environmental services and support, ecological risk assessment, and research benefitting the DOE-ID mission.

165

Performance Assessment Monitoring Plan for the Hanford Site Low-Level Burial Grounds  

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy Order 435.1, Radioactive Waste Management, requires a disposal authorization statement authorizing operation (or continued operation) for low-level waste disposal facilities. In fulfillment of these requirements, a disposal authorization statement was issued on October 25, 1999, authorizing the Hanford Site to transfer, receive, possess, and dispose of low-level radioactive waste at the 200 East Area burial grounds and the 200 West Area burial grounds. One of the conditions is that monitoring plans for the 200 East Area and 200 West Area low-level burial grounds be written and approved by the Richland Operations Office. As a result of a record of decision for the Hanford Site Solid Waste Program and acceptance of the Hanford Site Solid Waste Environmental Impact Statement, the use of the low-level burial ground (LLBG) as a disposal ...

2006-03-30

166

Quarterly technical progress report - base program on energy related research. Quarterly report, February 1--April 30, 1994  

Energy Technology Data Exchange (ETDEWEB)

Research is presented on oil and gas technologies, advanced systems for fossil fuels, environmental technologies for remediation and waste management, applied energy science on heavy oil and plastics coprocessing, and fossil fuel and hydrocarbon conversion using hydrogen rich plasma.

1997-05-01

167

Melter Disposal Strategic Planning Document  

Energy Technology Data Exchange (ETDEWEB)

This document describes the proposed strategy for disposal of spent and failed melters from the tank waste treatment plant to be built by the Office of River Protection at the Hanford site in Washington. It describes program management activities, disposal and transportation systems, leachate management, permitting, and safety authorization basis approvals needed to execute the strategy.

2000-09-25

168

Management of sampling and analysis activities in DOE`s Office of Environmental Management  

Energy Technology Data Exchange (ETDEWEB)

DOE`s Office of Environmental Management (EM) is responsible for managing waste and cleaning up contamination at DOE sites across the United States. A substantial fraction of the work performed for EM includes sampling and analysis activities. This paper outlines the Sample Management Programs, achievements to date, and future directions.

1995-12-31

169

Community Geothermal Technology Program: Hawaii glass project. Final report  

Energy Technology Data Exchange (ETDEWEB)

Objective was to develop a glass utilizing the silica waste material from geothermal energy production, and to supply local artists with this glass to make artistic objects. A glass composed of 93% indigenous Hawaiian materials was developed; 24 artists made 110 objects from this glass. A market was found for art objects made from this material.

1988-01-20

170

Visiatome: The French Discovery and Information Center on Radioactive Waste Management  

International Nuclear Information System (INIS)

The French radioactive waste management act of December 30, 1991, included two key provisions. It initiated a major research program with three areas of investigation concerning high-level long-lived radioactive waste management routes, and called for the Government to submit a legislative proposal to Parliament within 15 years (by 2006) specifying the policy guidelines adopted. Considering the sensitive nature of the subject, the questions surrounding the issue of radioactive waste, and the social, economic and environmental concerns for present and future generations, the Government has inaugurated, in 2005, a nationwide public debate on these issues between the submittal of the research reports and the parliamentary discussion of the proposed law. In this context, the CEA has decided to concentrate at Marcoule the expertise and experience acquired in the area of radioactive waste ...

171

Municipal solid waste management in Africa: Strategies and livelihoods in Yaounde, Cameroon  

International Nuclear Information System (INIS)

This paper provides an overview of the state of municipal solid waste (MSW) management in the capital of Cameroon, Yaounde, and suggests some possible solutions for its improvement. The institutional, financial, and physical aspects of MSW management, as well as the livelihoods of the population, were analyzed. Our study revealed that distances and lack of infrastructure have a major impact on waste collection. Garbage bins are systematically mentioned as the primary infrastructure needed by the population in all quarters, whether it be a high or low standard community. The construction of transfer stations and the installation of garbage bins are suggested as a solution to reduce distances between households and garbage bins, thus improving waste collection vehicle accessibility. Transfer stations and garbage bins would enable the official waste collection company to expand its range of services and ...

2009-02-01

172

Hazardous waste treatment and environmental remediation research  

Energy Technology Data Exchange (ETDEWEB)

Los Alamos National Laboratory (LANL) is currently evaluating hazardous waste treatment and environmental remediation technologies in existence and under development to determine applicability to remediation needs of the DOE facilities under the Albuquerque Operations Office and to determine areas of research need. To assist LANL is this effort, Science Applications International Corporation (SAIC) conducted an assessment of technologies and monitoring methods that have been demonstrated or are under development. The focus of this assessment is to: (1) identify existing technologies for hazardous waste treatment and environmental remediation of old waste sites; (2) identify technologies under development and the status of the technology; (3) assess new technologies that need development to provide adequate hazardous waste treatment and remedial action technologies for DOD and DOE sites; and (4) identify ...

1989-09-29

173

DOE assay methods used for characterization of contact-handled transuranic waste  

International Nuclear Information System (INIS)

US Department of Energy methods used for characterization of contact-handled transuranic (CH-TRU) waste prior to shipment to the Waste Isolation Pilot Plant (WIPP) are described and listed by contractor site. The methods described are part of the certification process. All CH-TRU waste must be assayed for determination of fissile material content and decay heat values prior to shipment and prior to storage on-site. Both nondestructive assay (NDA) and destructive assay methods are discussed, and new NDA developments such as passive-action neutron (PAN) crate counter improvements and neutron imaging are detailed. Specifically addressed are assay method physics; applicability to CH-TRU wastes; calibration standards and implementation; operator training requirements and practices; assay procedures; assay precision, bias, and limit of detection; and assay limitation. While PAN is a new technique and does not ...

174

DOE assay methods used for characterization of contact-handled transuranic waste  

Energy Technology Data Exchange (ETDEWEB)

US Department of Energy methods used for characterization of contact-handled transuranic (CH-TRU) waste prior to shipment to the Waste Isolation Pilot Plant (WIPP) are described and listed by contractor site. The methods described are part of the certification process. All CH-TRU waste must be assayed for determination of fissile material content and decay heat values prior to shipment and prior to storage on-site. Both nondestructive assay (NDA) and destructive assay methods are discussed, and new NDA developments such as passive-action neutron (PAN) crate counter improvements and neutron imaging are detailed. Specifically addressed are assay method physics; applicability to CH-TRU wastes; calibration standards and implementation; operator training requirements and practices; assay procedures; assay precision, bias, and limit of detection; and assay limitation. While PAN is a new technique and does not ...

1991-08-01

175

Study on quality assurance for high-level radioactive waste disposal project  

International Nuclear Information System (INIS)

The U.S. Department of Energy (DOE) has developed comparatively detailed quality assurance requirements for the high-level radioactive waste disposal systems. Quality assurance is recognized as a key issue for confidence building and smooth implementation of the HLW program in Japan, and Japan is at an initial phase of repository development. Then the quality assurance requirements at site research and site selection, site characterization, and site suitability analysis used in the Yucca Mountain project were examined in detail and comprehensive descriptions were developed using flow charts. Additionally, the applicability to the Japan high-level radioactive waste disposal project was studied. The examination and study were performed for the following QA requirements: The requirements that have the relative importance at site research and site selection, site characterization, and site suitability analysis (such as planning ...

2005-03-01

176

SOW for Services Provided by the Waste Sampling Characterization Facility (WSCF) for the Environmental Compliance Program during CY 2000  

Energy Technology Data Exchange (ETDEWEB)

This document defines analytical services the Waste Sampling and Characterization Facility (WSCF) shall provide the Environmental Compliance Program (ECP) throughout calendar year (CY) 2000. Two organizations within ECP are responsible for monitoring liquid and gaseous effluents and the environment immediately around facilities that contain or may contain radioactive and hazardous materials. Monitoring & Reporting (M&R), of Fluor Hanford Environmental Services, is responsible for effluent monitoring data, and Environmental Monitoring & Investigations (EMI), of Waste Management Technical Services, Inc., for near-facility environmental monitoring data. These organizations serve numerous projects, some of which are managed by other companies such as CH2M HILL and Bechtel Hanford, Inc. Monitoring data are collected and evaluated to determine their state of compliance with applicable federal and state regulations ...

2000-06-01

177

Assessing plantation biomass for co-firing with coal in northern Indiana: a linear programming approach  

Energy Technology Data Exchange (ETDEWEB)

Tightening environmental regulations and the signing of the Kyoto protocol have prompted electric utilities to consider co-firing biomass with coal to reduce the levels of CO{sub 2}, SO{sub 2} and NOx in stack emissions. This analysis examines the cost competitiveness of plantation produced woody biomass and waste wood with coal in electricity production. A case study of woody biomass production and co-firing in northern Indiana is presented. A linear programming model was developed to examine the optimal co-firing blend of coal and biomass while minimizing variable, cost, including the cost of ash disposal and material procurement costs. This model was used to examine situations where coal is the primary fuel and waste wood, willow trees, or both are available for fuel blending. The results indicate that co-firing woody biomass is cost-effective for the power plant. Sensitivity analysis explored the effect of ...

2000-07-01

178

Advanced evaporator technology progress report FY 1992  

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the work that was completed in FY 1992 on the program {open_quotes}Technology Development for Concentrating Process Streams.{close_quotes} The purpose of this program is to evaluate and develop evaporator technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process. Concentrating these streams and minimizing the volume of waste generated can significantly reduce disposal costs; however, equipment to concentrate the streams and recycle the decontaminated condensates must be installed. LICON, Inc., is developing an evaporator that shows a great deal of potential for this application. In this report, concepts that need to be incorporated into the design of an evaporator operated in a radioactive environment are discussed. These concepts include criticality safety, remote operation and maintenance, and materials of construction. Both ...

1995-01-01

179

Innovative coke oven gas cleaning system for retrofit applications. Quarterly environmental monitoring report No. 2, July 1, 1991--September 30, 1991  

Energy Technology Data Exchange (ETDEWEB)

The EMP consists of a Compliance Monitoring Sampling Program and a Supplemental monitoring Sampling Program. The Compliance Monitoring Sampling Program will be conducted during a summer and a winter Baseline periods during the Pre-Construction/Construction phases of the Project and during a summer and a winter period following the successful Startup and Operational phase of the completed Project. compliance monitoring consist of conducting all the sampling and observation programs associated with existing required Federal, State, and Local Regulations, Permits and Orders. These include air, water, and waste monitoring and OSHA and NESHAP monitoring. The Supplemental Monitoring Program will also be conducted during a summer and a winter Baseline periods during the Pre-Construction/Construction phases of the Demonstration Facility and during a summer and a winter ...

1992-09-21

180

Innovative coke oven gas cleaning system for retrofit applications  

Energy Technology Data Exchange (ETDEWEB)

The EMP consists of a Compliance Monitoring Sampling Program and a Supplemental monitoring Sampling Program. The Compliance Monitoring Sampling Program will be conducted during a summer and a winter Baseline periods during the Pre-Construction/Construction phases of the Project and during a summer and a winter period following the successful Startup and Operational phase of the completed Project. compliance monitoring consist of conducting all the sampling and observation programs associated with existing required Federal, State, and Local Regulations, Permits and Orders. These include air, water, and waste monitoring and OSHA and NESHAP monitoring. The Supplemental Monitoring Program will also be conducted during a summer and a winter Baseline periods during the Pre-Construction/Construction phases of the Demonstration Facility and during a summer and a winter ...

1992-09-21

181

Groundwater quality assessment plan for single-shell tank waste management Area U at the Hanford Site  

Energy Technology Data Exchange (ETDEWEB)

Waste Management Area U (WMA U) includes the U Tank Farm, is currently regulated under RCRA interim-status regulations, and is scheduled for closure probably post-2030. Groundwater monitoring has been under an evaluation program that compared general contaminant indicator parameters from downgradient wells to background values established from upgradient wells. One of the indicator parameters, specific conductance, exceeded its background value in one downgradient well triggering a change from detection monitoring to a groundwater quality assessment program. The objective of the first phase of this assessment program is to determine whether the increased concentrations of nitrate and chromium in groundwater are from WMA U or from an upgradient source. Based on the results of the first determination, if WMA U is not the source of contamination, then the site will revert to detection monitoring. If WMA U ...

2000-03-21

182

Treatment of waste rock piles at Wood Cadillac using a reducing trickling filter; Traitement des resurgences du parc a residus miniers Wood Cadillac au moyen d'un biofiltre reducteur  

Energy Technology Data Exchange (ETDEWEB)

The Ministere des Ressources naturelles du Quebec (Quebec Natural Resources Department) implemented a remedial program to treat the waste rock pile at Wood Cadillac, located near Cadillac, in Abitibi, Quebec. The solutions proposed by INRS-Georessources and ENVIROCONSEIL are aimed at eliminating erosion and stabilizing the geochemical processes. Part of the proposed solution also included the use of a reducing trickling filter for the treatment of acid leachates, which also contain arsenic when exiting the waste rock pile. The trickling filter is composed of forest tailings in which the bacteria reduce the sulphates and stimulate the precipitation of arsenic into arsenic sulphates. This is a new treatment that was developed following laboratory experiments which demonstrated the feasibility of the process and quantified the parameters. A demonstration unit was constructed by ENVIROCONSEIL and installed at the Wood Cadillac ...

2000-07-01

183

The behavior of waste rock piles; Le comportement des haldes de steriles  

Energy Technology Data Exchange (ETDEWEB)

Under the auspices of the Mine Environment Neutral Drainage (MEND) Program, several waste rock piles were monitored and characterized. Acid rock drainage (ARD) became a mechanism better understood based on the data acquired during these projects. Numerical simulation was used to better comprehend the quantitative issues associated with the characterization of three specific sites for the purpose of this study. The sites selected were the south waste rock pile of the Doyon Mine in Quebec, the Northdale of the mining district of Ronnenberg in Germany, and the waste rock pile of the Sugar Shack South of the Questa mine in New Mexico. The observed and simulated conditions were very distinct from one mine to another, even if the same mechanisms were involved. The dominant oxygen and heat transfer mechanisms displayed the most varied behavior between the sites. ARD control or site rehabilitation decisions ...

2000-07-01

184

The Principles of Radioactive Waste Management  

CERN Document Server

The Principles of Radioactive Waste Management

1995-01-01

185

Establishing a nationalsystem for radioactive waste management  

CERN Document Server

Establishing a nationalsystem for radioactive waste management

1995-01-01

186

Waste to energy technologies.  

Science.gov (United States)

No abstract prepared.

2010-04-01

187

REGULATIONS ON PHOTOVOLTAIC MODULE DISPOSAL AND RECYCLING.  

Energy Technology Data Exchange (ETDEWEB)

Environmental regulations can have a significant impact on product use, disposal, and recycling. This report summarizes the basic aspects of current federal, state and international regulations which apply to end-of-life photovoltaic (PV) modules and PV manufacturing scrap destined for disposal or recycling. It also discusses proposed regulations for electronics that may set the ground of what is to be expected in this area in the near future. In the US, several states have started programs to support the recycling of electronic equipment, and materials destined for recycling often are excepted from solid waste regulations during the collection, transfer, storage and processing stages. California regulations are described separately because they are different from those of most other states. International agreements on the movement of waste between different countries may pose barriers to cross-border shipments. Currently ...

2001-01-29

188

Nevada Test Site 2007 Data Report: Groundwater Monitoring Program Area 5 Radioactive Waste Management Site  

Science.gov (United States)

This report is a compilation of the groundwater sampling results from three monitoring wells located near the Area 5 Radioactive Waste Management Site (RWMS) at the Nevada Test Site (NTS), Nye County, Nevada, for calendar year 2007. The NTS is an approximately 3,561 square kilometer (1,375 square mile) restricted-access federal installation located approximately 105 kilometers (65 miles) northwest of Las Vegas, Nevada (Figure 1). Pilot wells UE5PW-1, UE5PW-2, and UE5PW-3 are used to monitor the groundwater at the Area 5 RWMS (Figure 2). In addition to groundwater monitoring results, this report includes information regarding site hydrogeology, well construction, sample collection, and meteorological data measured at the Area 5 RWMS. The disposal of low-level radioactive waste and mixed low-level radioactive waste at the Area 5 RWMS is regulated by U.S. Department of Energy (DOE) Order 435.1, 'Radioactive ...

2008-01-01

189

Telecommunications Network Plan  

International Nuclear Information System (INIS)

The Office of Civilian Radioactive Waste Management (OCRWM) must, among other things, be equipped to readily produce, file, store, access, retrieve, and transfer a wide variety of technical and institutional data and information. The data and information regularly produced by members of the OCRWM Program supports, and will continue to support, a wide range of program activities. Some of the more important of these information communication-related activities include: supporting the preparation, submittal, and review of a license application to the Nuclear Regulatory Commission (NRC) to authorize the construction of a geologic repository; responding to requests for information from parties affected by and/or interested in the program; and providing evidence of compliance with all relevant Federal, State, local, and Indian Tribe regulations, statutes, and/or treaties. The OCRWM Telecommunications Network ...

1997-10-07

190

Implementation plan for liquid low-level radioactive waste tank systems for fiscal year 1995 at Oak Ridge National Laboratory under the Federal Facility Agreement, Oak Ridge, Tennessee  

Energy Technology Data Exchange (ETDEWEB)

This document is the third annual revision of the plans and schedules for implementing the Federal Facility Agreement (FFA) compliance program, originally submitted in 1992 as ES/ER-17&D1, Federal Facility Agreement Plans and Schedules for Liquid Low-Level Radioactive Waste Tank Systems at Oak Ridge National Laboratory, Oak Ridge, Tennessee. This document summarizes the progress that has been made to date in implementing the plans and schedules for meeting the FFA commitments for the Liquid Low-Level Waste (LLLW) System at Oak Ridge National Laboratory (ORNL). Information presented in this document provides a comprehensive summary to facilitate understanding of the FFA compliance program for LLLW tank systems and to present plans and schedules associated with remediation, through the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) process, of LLLW tank systems that ...

1995-06-01

191

Performance objectives for the Hanford immobilized low-activity waste (ILAW) performance assessment  

Energy Technology Data Exchange (ETDEWEB)

Before low-level waste may be disposed of, a performance assessment must be written and then approved by the DOE (DOE 1988a DOE 1999a). The performance assessment is to determine whether ''reasonable assurance'' exists that the performance objectives of the disposal facility will be met. The DOE requirements for waste disposal (DOE 1988a DOE 1999a) require the protection of public health and safety; and the protection of the environment. Although quantitative limits are sometimes stated (for example, the all-pathways exposure limit is 25 mrem/year), usually the requirements are stated in a general nature. Quantitative limits were established by: investigating all potentially applicable regulations as well as interpretations of the review panels which DOE has established to review performance assessments, interacting with program management to establish the additional requirements of the ...

1999-09-09

192

Transuranic material recovery in the Integral Fast Reactor fuel cycle demonstration  

Energy Technology Data Exchange (ETDEWEB)

The Integral Fast Reactor is an innovative liquid metal reactor concept that is being developed by Argonne National Laboratory. It takes advantage of the properties of metallic fuel and liquid metal cooling to offer significant improvements in reactor safety, operation, fuel cycle economics, environmental protection, and safeguards. The plans for demonstrating the IFR fuel cycle, including its waste processing options, by processing irradiated fuel from the Experimental Breeder Reactor-II fuel in its associated Fuel Cycle Facility have been developed for the first refining series. This series has been designed to provide the data needed for the further development of the IFR program. An important piece of the data needed is the recovery of TRU material during the reprocessing and waste operations.

1993-01-01

193

Transuranic material recovery in the Integral Fast Reactor fuel cycle demonstration  

Energy Technology Data Exchange (ETDEWEB)

The Integral Fast Reactor is an innovative liquid metal reactor concept that is being developed by Argonne National Laboratory. It takes advantage of the properties of metallic fuel and liquid metal cooling to offer significant improvements in reactor safety, operation, fuel cycle economics, environmental protection, and safeguards. The plans for demonstrating the IFR fuel cycle, including its waste processing options, by processing irradiated fuel from the Experimental Breeder Reactor-II fuel in its associated Fuel Cycle Facility have been developed for the first refining series. This series has been designed to provide the data needed for the further development of the IFR program. An important piece of the data needed is the recovery of TRU material during the reprocessing and waste operations.

1993-03-01

194

Selective dissolution and recovery of depleted uranium from armor plate. Final report, 26 June 1986-5 May 1987  

Energy Technology Data Exchange (ETDEWEB)

The impacted armor targets used in testing high density armor-piercing ammunition containing depleted uranium (DU) are subject to disposal as low-level radioactive waste. Because of the costs associated with disposal of the entire armor plate and the limited use of secured commercial sites in the future, the U.S. Army is seeking to identify and evaluate new technologies for decontaminating these armor plates. The objectives of this Phase I SBIR program are two-fold, namely: to develop a selective solvent that can decontaminate impacted armor targets containing DU for disposal or recycle, and to identify and characterize technologies that can remove depleted uranium from the solvent for solvent recycle and uranium recovery for easier hazardous-waste disposal.

1987-05-05

195

Interim radiological safety standards and evaluation procedures for subseabed high-level waste disposal  

Energy Technology Data Exchange (ETDEWEB)

The Seabed Disposal Project (SDP) was evaluating the technical feasibility of high-level nuclear waste disposal in deep ocean sediments. Working standards were needed for risk assessments, evaluation of alternative designs, sensitivity studies, and conceptual design guidelines. This report completes a three part program to develop radiological standards for the feasibility phase of the SDP. The characteristics of subseabed disposal and how they affect the selection of standards are discussed. General radiological protection standards are reviewed, along with some new methods, and a systematic approach to developing standards is presented. The selected interim radiological standards for the SDP and the reasons for their selection are given. These standards have no legal or regulatory status and will be replaced or modified by regulatory agencies if subseabed disposal is implemented. 56 refs., 29 figs., 15 tabs.

1997-06-01

196

Facilities evaluation report  

Energy Technology Data Exchange (ETDEWEB)

The Buried Waste Integrated Demonstration (BWID) is a program of the Department of Energy (DOE) Office of Technology Development whose mission is to evaluate different new and existing technologies and determine how well they address DOE community waste remediation problems. Twenty-three Technical Task Plans (TTPs) have been identified to support this mission during FY-92; 10 of these have identified some support requirements when demonstrations take place. Section 1 of this report describes the tasks supported by BWID, determines if a technical demonstration is proposed, and if so, identifies the support requirements requested by the TTP Principal Investigators. Section 2 of this report is an evaluation identifying facility characteristics of existing Idaho National Engineering Laboratory (INEL) facilities that may be considered for use in BWID technology demonstration activities.

1992-04-01

197

Catalytic ammonia decomposition over industrial-waste-supported Ru catalysts  

Energy Technology Data Exchange (ETDEWEB)

Industrial solid wastes (fly ash and red mud, a by-product of the aluminium industry) have been employed as supports for preparation of Ru-based catalysts. Physical and chemical treatments on red mud were conducted and these modified supports were also used for preparation of Ru-based catalysts. Those Ru catalysts were characterized by various techniques such as N2 adsorption, H{sub 2} adsorption, XRD, XPS, and temperature-programmed reduction (TPR), and were then tested for catalytic ammonia decomposition to hydrogen. It was found that red-mud-supported Ru catalyst exhibits higher ammonia conversion and hydrogen production than fly-ash-supported catalyst. Heat and chemical treatments of the red mud greatly improve the catalytic activity. Moreover, a combination of acid and heat treatments produces the highest catalytic conversion of ammonia. 35 refs., 4 figs., 4 tabs.

2007-05-15

198

Summary of the Waste Management Programs at uranium recovery facilities as they relate to the 40 CFR Part 192 standards  

International Nuclear Information System (INIS)

This study evaluates the degree to which surface impoundments at licensed facilities comply with significant changes in NRC requirements initiated by enactment of EPA's final environmental standards for uranium recovery facilities (40 CFR Part 192). Impoundment liner requirements, ground-water protection standards, ground-water monitoring and corrective action programs, and site closure standards are the most significant regulatory modifications. The compliance status of 30 conventional mills and 31 in-situ mines is determined from a review of Nuclear Regulatory Commission and agreement state docket files through November, 1983. Results of this review show that a majority of conventional uranium mill tailings management systems are deficient with respect to liner requirements for new impoundments or proposed expansions to existing impoundments, as well as with respect to some aspects of ground-water monitoring and compliance programs. ...

199

222-S Laboratory maintenance implementation plan  

Energy Technology Data Exchange (ETDEWEB)

This Maintenance Improvement Plan has been developed for maintenance functions associated with the 222-S Laboratory. This plan is developed from the guidelines presented by Department of Energy (DOE) Order 4330.4B, Maintenance Management Program (DOE 1994), Chapter 11. The objective of this plan is to provide information for establishing and identifying WMH conformance programs and policies applicable to implementation of DOE Order 4330.4B guidelines. In addition, this maintenance plan identifies the actions necessary to develop a cost effective and efficient maintenance program at 222-S Laboratory. Maintenance activities are mainly going to be performed by existing maintenance organizations within Waste Management Federal Services of Hanford (WMH). Most maintenance performed at 222-S Laboratory is performed by the 222-S Laboratory maintenance organization. This 222-S Laboratory Maintenance ...

1997-08-13

200

Waste Food Storage at Fortress Rocks  

Science.gov (United States)

... of waste food generated at McMurdo Station. Some of the difficulties of disposing of waste food ... change waste generation or management at the site? Yes. This will be a temporary waste management ...

201

User's guide to PROTOCOL, a numerical simulator for the dissolution reactions of inorganic solids in aqueous solutions  

Energy Technology Data Exchange (ETDEWEB)

This report provides a user's manual for PROTOCOL, a comprehensive coupled kinetic/equilibrium computer program for analyzing the dissolution reactions of solids with aqueous solutions, specifically applied to the potential corrosion of vitrified nuclear waste by groundwater. The capabilities and available options are summarized as well as instructions for setting up and running problems. Also described in this report and included in the PROTOCOL software package are MASTER, a master file of species thermodynamic data, MANEQL, a preprocessor program and POSTP, a postprocessor. POSTP provides offline plotting using the CRAY-1 DISSPLA 9.0 graphics library. PROTOCOL is operational on the CDC-7600 and CRAY-1 computers at the Lawrence Livermore National Laboratory. 7 references, 10 figures, 2 tables.

1984-10-01

202

Household batteries: Evaluation of collection methods  

Energy Technology Data Exchange (ETDEWEB)

While it is difficult to prove that a specific material is causing contamination in a landfill, tests have been conducted at waste-to-energy facilities that indicate that household batteries contribute significant amounts of heavy metals to both air emissions and ash residue. Hennepin County, MN, used a dual approach for developing and implementing a special household battery collection. Alternative collection methods were examined; test collections were conducted. The second phase examined operating and disposal policy issues. This report describes the results of the grant project, moving from a broad examination of the construction and content of batteries, to a description of the pilot collection programs, and ending with a discussion of variables affecting the cost and operation of a comprehensive battery collection program. Three out-of-state companies (PA, NY) were found that accept spent batteries; difficulties in ...

1992-01-01

203

Household batteries: Evaluation of collection methods  

Energy Technology Data Exchange (ETDEWEB)

While it is difficult to prove that a specific material is causing contamination in a landfill, tests have been conducted at waste-to-energy facilities that indicate that household batteries contribute significant amounts of heavy metals to both air emissions and ash residue. Hennepin County, MN, used a dual approach for developing and implementing a special household battery collection. Alternative collection methods were examined; test collections were conducted. The second phase examined operating and disposal policy issues. This report describes the results of the grant project, moving from a broad examination of the construction and content of batteries, to a description of the pilot collection programs, and ending with a discussion of variables affecting the cost and operation of a comprehensive battery collection program. Three out-of-state companies (PA, NY) were found that accept spent batteries; difficulties in ...

1992-12-31

204

Waste Handling Shaft concrete liner degradation conclusions and recommendations  

International Nuclear Information System (INIS)

The primary function of the Waste Handling Shaft (WHS) at the Waste Isolation Pilot Plant (WIPP) is to permit the transfer of radioactive waste from the surface waste handling building to the underground storage area. It also serves as an intake shaft for small volumes of air during normal storage operations and as an emergency escape route. Part of the construction was the placement of a concrete liner and steel reinforced key in 1984. During a routine shaft inspection in May 1990, some degradation of the WHS concrete liner was observed between the depths of 800 and 900 feet below the ground surface. Detailed investigations of the liner had been carried out by Sandia National Laboratories and by Westinghouse Electric Corporation Waste Isolation Division (WID) through Lankard Materials Laboratory. Observations, reports, and data support the conclusion that the concrete degradation, ...

205

Gamma-ray pulse height spectrum analysis on systems with multiple Ge detectors using a spectrum summing  

Energy Technology Data Exchange (ETDEWEB)

A technique has been developed at the Idaho National Engineering Laboratory to sum high resolution gamma-ray pulse spectra from systems with multiple Ge detectors. Lockheed Martin Idaho Technologies Company operates a multi-detector spectrometer configuration at the Stored Waste Examination Pilot Plant facility which is used to characterize the radio nuclide contents in waste drums destined for shipment to Waste Isolation Pilot Plant. This summing technique was developed to increase the sensitivity of the system, reduce the count times required to properly quantify the radionuclides and provide a more consistent methodology for combining data collected from multiple detectors. In spectrometer systems with multiple detectors looking at non homogenous waste forms it is often difficult to combine individual spectrum analysis results from each detector to obtain a meaningful result for the total ...

1997-05-01

206

Evaluation of the impact of RCRA amendments on waste-to-energy activities by using a system simulation computer code  

Energy Technology Data Exchange (ETDEWEB)

The primary methodology that is used for disposal of municipal solid waste is the use of land fills; 80--85% of the municipal solid waste (MSW) produced in the country currently is land filled. The two other disposal alternatives used are recycling and incineration. Waste-to-energy technology (WTE) which incinerates MSW to produce electricity and/or steam is attractive in other cases since it reduces landfill volume, reduces the consumption of fossil and other fuels, and produces a revenue stream from the sale of the electricity or steam. The gaseous effluents from landfills can also be used to fuel power plants. Recycling and material separation programs can have a substantial impact on the throughput and heating value of MSW collected and thus impact WTE plant economics; the magnitude of the impact will depend upon a number of factors such as what materials and what fraction are separated and ...

1994-09-01

207

2008 Data Report: Groundwater Monitoring Program Area 5 Radioactive Waste Management Site  

Science.gov (United States)

This report is a compilation of the groundwater sampling results from the Area 5 Radioactive Waste Management Site (RWMS) including calendar year 2008 results. Each of the three Pilot Wells was sampled on March 11, 2008, and September 10, 2008. These wells were sampled for the following indicators of contamination: pH, specific conductance, total organic carbon, total organic halides, and tritium. Indicators of general water chemistry (cations and anions) were also monitored. Results from all samples collected in 2008 were within the limits established by agreement with the Nevada Division of Environmental Protection for each analyte. These data indicate that there has been no measurable impact to the uppermost aquifer from the Area 5 RWMS. There were no significant changes in measured groundwater parameters compared to previous years. Other information in the report includes an updated Cumulative Chronology for the Area 5 RWMS Groundwater Monitoring ...

2009-01-13

208

2006 Data Report: Groundwater Monitoring Program Area 5 Radioactive Waste Management Site  

Science.gov (United States)

This report is a compilation of the groundwater sampling results from the Area 5 Radioactive Waste Management Site (RWMS) for calendar year 2006. Pilot wells UE5PW-1, UE5PW-2, and UE5PW-3 were sampled in April and October 2006 for the following indicators of contamination: pH, specific conductance, total organic carbon, total organic halides, and tritium. Indicators of general water chemistry (cations and anions) were also monitored. Results from all samples collected in 2006 were within the limits established by agreement with the Nevada Division of Environmental Protection for each analyte. These data indicate that there has been no measurable impact to the uppermost aquifer from the Area 5 RWMS. There were no significant changes in measured groundwater parameters compared to previous years. Other information in the report includes an updated Cumulative Chronology for the Area 5 RWMS Groundwater Monitoring Program and a brief description of ...

2007-02-01

209

Pressurized fluidized-bed hydroretorting of Eastern oil shales. Annual report, June 1991--May 1992  

Energy Technology Data Exchange (ETDEWEB)

The Devonian oil shales of the Eastern United States are a significant domestic energy resource. The overall objective of the multi-year program, initiated in October 1987 by the US Department of Energy is to perform the research necessary to develop the Pressurized Fluidized-Bed Hydroretorting (PFH) process for producing oil from Eastern oil shales. The program also incorporates research on technologies in areas such as raw shale preparation, beneficiation, product separation, and waste disposal that have the potential of improving the economics and/or environmental acceptability of recovering oil from oil shales using the PFH process. The results of the original 3-year program, which was concluded in May 1991, have been summarized in a four-volume final report published by IGT. DOE subsequently approved a 1-year extension to the program to further develop the PFH process ...

1992-11-01

210

Pressurized fluidized-bed hydroretorting of Eastern oil shales  

Energy Technology Data Exchange (ETDEWEB)

The Devonian oil shales of the Eastern United States are a significant domestic energy resource. The overall objective of the multi-year program, initiated in October 1987 by the US Department of Energy is to perform the research necessary to develop the Pressurized Fluidized-Bed Hydroretorting (PFH) process for producing oil from Eastern oil shales. The program also incorporates research on technologies in areas such as raw shale preparation, beneficiation, product separation, and waste disposal that have the potential of improving the economics and/or environmental acceptability of recovering oil from oil shales using the PFH process. The results of the original 3-year program, which was concluded in May 1991, have been summarized in a four-volume final report published by IGT. DOE subsequently approved a 1-year extension to the program to further develop the PFH process ...

1992-11-01

211

Advanced Industrial Materials (AIM) Program: Compilation of project summaries and significant accomplishments, FY 1995  

Energy Technology Data Exchange (ETDEWEB)

In many ways, the Advanced Industrial Materials (AIM) Program underwent a major transformation in Fiscal Year 1995 and these changes have continued to the present. When the Program was established in 1990 as the Advanced Industrial Concepts (AIC) Materials Program, the mission was to conduct applied research and development to bring materials and processing technologies from the knowledge derived from basic research to the maturity required for the end use sectors for commercialization. In 1995, the Office of Industrial Technologies (OIT) made radical changes in structure and procedures. All technology development was directed toward the seven ``Vision Industries`` that use about 80% of industrial energy and generated about 90% of industrial wastes. The mission of AIM has, therefore, changed to ``Support development and commercialization of new or improved materials to improve productivity, product ...

1996-04-01

212

Standardization/improvement and technical development of light water reactor power station in Japan(BWR)  

Energy Technology Data Exchange (ETDEWEB)

In order to realize improve of reliability and economy by duplicate production, rapid supply of repair parts from standardized storage, such were expected as to have continuous order of standardized plant, to ignore site condition, to avoid expansion of regulatory requirement. Standardization program was planned to limitedly promote standardization of safety-related design concept, major specification and basic system composition of reactor and primary systems. The area of standardization had been tried to expand to BOP such as general arrangement and rad-waste system.

1985-07-01

213

Site characterization progress report: Yucca Mountain, Nevada, October 1, 1990--March 31, 1991; Number 4  

Energy Technology Data Exchange (ETDEWEB)

In accordance with the requirements of Section 113 (b) (3) of the Nuclear Waste Policy Act of 1982, as amended (NWPA), the US Department of Energy (DOE) has prepared this report on the progress of site characterization activities at Yucca Mountain, Nevada, for the period October 1, 1990, through March 31, 1991. This report is the fourth in a series of reports that are issued at intervals of approximately six months during site characterization. The report covers a number of initiatives to improve the effectiveness of the site characterization program, and covers continued efforts related to preparatory activities, Study Plans, and performance assessment.

1991-10-01

214

Scientific reference on the long time evolution of spent fuels; Referentiel scientifique sur l'evolution a long terme des combustibles uses  

Energy Technology Data Exchange (ETDEWEB)

This report is published in the framework of the 1991 French law for the nuclear waste management. The state of the art reported here concerns the long term evolution of spent fuel in the various environmental conditions corresponding to dry storage and geological disposal: closed system, air and water saturated medium. This review is based on the results of the french PRECCI project (Research Program on Long term Evolution of Spent Nuclear Fuel) and on literature data. (authors)

2005-03-15

215

Radiation safety in industrial applications  

International Nuclear Information System (INIS)

Oil and gas industry is the largest user of radioactive materials in Nigeria. They make use of radiation generators, sealed and unsealed radioactive sources.Some of these are potentially dangerous to human health and environment if not properly controlled. here is also the need to maintain control over occupational exposures to radiation, as well as to protect the public and the environment through proper management of wastes that may be radiologically hazardous. To minimize these, effective regulatory infrastructure is being put in place.For a smooth take-off of the nuclear power program, the National Nuclear Regulatory Authority and other stake holders in the nuclear industry need to start to put together licensing procedure for these.

2008-03-17

216

Paul Scherrer Institute Scientific Report 2000. Volume IV: Nuclear Energy and Safety  

Energy Technology Data Exchange (ETDEWEB)

Nuclear energy related research in Switzerland is concentrated at PSI's Nuclear Energy and Safety Research Department (NES). The activities of the department are concentrated on three main domains of: Safety and related problems of operating plants; safety features of future reactor and fuel cycles; waste management. Comprehensive assessments of energy systems are carried out in cooperation with PSI's General Energy Research Department. Many of the programs are part of collaborations with universities, industry, or international organisations. Progress in 2000 in these topical areas is described in this report. A list of scientific publications in 2000 is also provided.

2001-03-01

217

Laboratory robotics systems at the Savannah River Laboratory  

International Nuclear Information System (INIS)

Many analytical chemistry methods normally used at the Savannah River site require repetitive procedures and handling of radioactive and other hazardous solutions. Robotics is being investigated as a method of reducing personnel fatigue and radiation exposure and also increasing product quality. Several applications of various commercially available robot systems are discussed involving cold (nonradioactive) and hot (radioactive) sample preparations and glovebox waste removal. Problems encountered in robot programming, parts fixturing, design of special robot hands and other support equipment, glovebox operation, and operator-system interaction are discussed. A typical robot system cost analysis for one application is given.

1983-11-16

218

Formation and decay of secondary actinides in water reactor and fast neutron reactors  

International Nuclear Information System (INIS)

Actinides other than the main uranium or plutonium isotopes take a growing part in the different stages of the nuclear cycle. For the French nuclear power program based on the development of light water reactors and fast breeders, many evaluations of the secondary actinides build up are made for the both reactor types using mainly the existing reactor codes. The comparison of these foreseen compositions with experimental results allows to perform some adjustments of the neutronic data. The secondary actinide compositions are given for some typical fuels and their consequences on the nuclear cycle are discussed. An hypothetical burning of these wastes in fast reactors has been studied and the main conclusions are reported.

219

Divison of Environmental Education and Development Fiscal Year 1992 annual report  

Energy Technology Data Exchange (ETDEWEB)

Primary design criterion for this division`s education activities is directly related to meeting the goal of environmental compliance on an accelerated basis and cleanup of the 1989 inventory of inactive sites and facilities by the year 2019. Therefore, the division`s efforts are directed toward stimulating knowledge and capability to achieve the goals while contributing to DOE`s overall goal of increasing scientific, mathematical, and technical literacy and competency. This annual report is divided into: overview, workforce development, academic partnerships, scholarships/fellowships, environmental restoration and waste management employment program, community colleges, outreach, evaluation, and principal DOE contacts.

1992-12-31

220

Bringing robotics technology down to Earth  

International Nuclear Information System (INIS)

Robotics technology is successfully being transitioned from space to terrestrial applications. It is being modified and enhanced to help in the US DOE's Environmental Restoration and Waste Management Program. Some examples of these applications, ranging from large multijointed manipulators to autonomously navigated remote vehicles, are outlined in this article. They include the following: underground storage tank technology demonstration; light-duty utility arm system; remotely controlled material-handling system; remotely operated excavator; self-guided transfer vehicle. 10 figs.

221

ORNL long-range environmental and waste management plan  

Energy Technology Data Exchange (ETDEWEB)

This report, the ORNL Long-Range Environmental and Waste Management Plan, is the annual update in a series begun in fiscal year 1985. Its primary purpose is to provide a thorough and systematic planning document to reflect the continuing process of site assessment, strategy development, and planning for the current and long-term control of environmental issues, waste management practices, and remedial action requirements. The document also provides an estimate of the resources required to implement the current plan. This document is not intended to be a budget document; it is, however, intended to provide guidance to both Martin Marietta Energy Systems, Inc., and the US Department of Energy (DOE) management as to the near order of magnitude of the resources (primarily funding requirements) and the time frame required to execute the strategy in the present revision of the plan. As with any document of this nature, the near-term (one to three ...

1989-09-01

222

Implementation Plan. Environmental Restoration and Waste Management Programmatic Environmental Impact Statement  

Energy Technology Data Exchange (ETDEWEB)

In accordance with the Department of Energy`s National Environmental Policy Act implementing procedures in Volume 10 of the Code of Federal Regulations, Section 1021,312, the Environmental Restoration and Waste Management Programmatic Environmental Impact Statement Implementation Plan has two primary purposes: to provide guidance for the preparation of the Programmatic Environmental Impact Statement and to record the issues resulting from the scoping and the extended public participation process. The Implementation Plan identifies and discusses the following: background of Environmental Restoration and Waste Management activities, the purpose of the Programmatic Environmental Impact Statement, and the relationship of the Programmatic Environmental Impact Statement to other Departmental initiatives (Chapter 1); need and purposes for action (Chapter 2); scoping process and results of the public participation program in ...

1994-01-01

223

From waste minimization to ISO 14000: Taiwan`s experience and prospects  

Energy Technology Data Exchange (ETDEWEB)

Taiwan has completed a very successful five-year industrial waste minimization (IWM) demonstration and promotion project sponsored by the government. From 1990 to 1995, the project successfully disseminated the IWM concept of pollution prevention (P2) to industries. It effectively reduced industrial waste while significantly benefitting the economy by assisting industries in implementing in-plant IWM programs. In July 1995, the second stage of the five-year IWM and ISO 14000 promotion project was initiated for further promoting the IWM, P2, and cleaner production and, in particular, coping with the upcoming international environmental management standards (ISO 14000). To assist industries in establishing an environmental management system (EMS) and accumulating related experience, an EMS pilot demonstration project of five model industries and an ISO 14001 EMS demonstration and promotion project for 22 factories in 13 ...

1996-12-31

224

Evaluation of methods to measure surface level in waste storage tanks: Second test sequence  

Energy Technology Data Exchange (ETDEWEB)

This report describes the results of a program conducted at the Pacific Northwest Laboratory (PNL) and Westinghouse Hanford Company (WHC) to identify alternative methods to measure the surface level in the waste tanks. This program examined commercially available devices for measuring the distance to a target. This is a continuation of a program started in FY93. In the first test sequence, tests were performed.on five devices to determine their applicability to measure the surface level in the waste tanks. The devices were the Enraf-Nonius{trademark} Model 872 Radar Gauge, the Enraf-Nonius{trademark} Model 854 Advanced Technology Gauge (ATG), the Stanley Tool Laser Measuring Device, the Robertshaw Inven-Tel{reg_sign} Precision Level Gauge, and the Micro Switch Model 942 Acoustic Sensor. In addition, discussions were held with several manufacturer representatives regarding other ...

1993-09-01

225

Activities performed within the program of Nuclear Safety Research on structural and cladding materials for innovative reactor systems able to transmute nuclear waste  

International Nuclear Information System (INIS)

Full text: The transmutation of nuclear waste to reduce the burden on a geological repository is a relevant topic within the Program of Nuclear Safety Research of the Research Centre Karlsruhe. Several studies have confirmed that a high efficiency of transmutation of actinides is reached in fast neutron spectrum reactor system. Therefore, an important effort is dedicated to the study of transmutation strategies with different fast reactors and their associated technologies. Moreover, in international contexts as Generation IV International Forum (GIF) and Sustainable Nuclear Energy Technology Platform (SNETP), fast reactors are considered in the frame of sustainable development of nuclear energy and reduction of waste. The systems that are currently under investigation, in the frame of the different fuel cycle scenarios, are liquid metal cooled and gas cooled fast reactors as well as Accelerator Driven Sub-critical ...

2009-10-05

226

UNSAT-H Version 3.0: Unsaturated Soil Water and Heat Flow Model Theory, User Manual, and Examples  

Energy Technology Data Exchange (ETDEWEB)

The UNSAT-H model was developed at Pacific Northwest National Laboratory (PNNL) to assess the water dynamics of arid sites and, in particular, estimate recharge fluxes for scenarios pertinent to waste disposal facilities. During the last 4 years, the UNSAT-H model received support from the Immobilized Waste Program (IWP) of the Hanford Site's River Protection Project. This program is designing and assessing the performance of on-site disposal facilities to receive radioactive wastes that are currently stored in single- and double-shell tanks at the Hanford Site (LMHC 1999). The IWP is interested in estimates of recharge rates for current conditions and long-term scenarios involving the vadose zone disposal of tank wastes. Simulation modeling with UNSAT-H is one of the methods being used to provide those estimates (e.g., Rockhold et al. 1995; Fayer et ...

2000-06-12

227

South Florida embraces waste-to-energy  

Energy Technology Data Exchange (ETDEWEB)

This paper reports that some regions have prepared for these days of disposal shortage with comprehensive waste plans that include a strong WTE presence. Witness Broward County, Florida's program, 12 years in planning by public and private entities, Broward is the second most populated county in the state, with 1.3 million residents and a heavy tourist population, which, together, produce 1.6 million tons of waste annually. The disposal program includes Waste Management, Inc.'s expansion of a 400-acre Central Disposal Sanitary Landfill, the county's new 588-acre landfill, composting, and curbside pickup for recyclables. And, this south Florida plan would not be complete without the two brand new combustion plants. Clean Air and Water Acts notwithstanding, the Florida Department of Environmental Regulation can induce standards stricter than the federal ...

1991-11-01

228

2003 Data Report: Groundwater Monitoring Program, Area 5 Radioactive Waste Management Site, Nevada Test Site  

Energy Technology Data Exchange (ETDEWEB)

This report is a compilation of the calendar year 2003 groundwater sampling results from the Area 5 Radioactive Waste Management Site, Nevada Test Site. Wells Ue5PW-1, Ue5PW-2, and Ue5PW-3 were sampled semi-annually for the required analytes: pH, specific conductance, total organic carbon (TOC), total organic halides (TOX), tritium, and major cations/anions. Results from all samples collected in 2003 were within established criteria. These data indicate that there has been no measurable impact to the uppermost aquifer from the Resource Conservation and Recovery Act (RCRA) regulated unit within the Area 5 Radioactive Waste Management Site and confirm that any previous detections of TOC and TOX were false positives. Contamination indicator data are presented in control chart and tabular form with investigation levels indicated. Gross water chemistry data are presented in graphical and tabular form. There were no major changes noted in the ...

2004-02-01

229

Restructured site characterization program at Yucca Mountain  

International Nuclear Information System (INIS)

During 1994 and the early part of 1995, the US Department of Energy's Yucca Mountain Site Characterization Office (YMSCO) and its parent organization, the Office of Civilian Radioactive Waste Management (OCRWM) underwent a significant restructuring. Senior Department officials provided the leadership to reorient the management, technical, programmatic, and public interaction approach to the US High Level Radioactive Waste Disposal Program. The restructuring involved reorganizing the federal staff, conducting meaningful strategic planning, improving the management system, rationalizing contractor responsibilities, focusing upon major products, and increasing stakeholder involvement. The restructured program has prioritized technical and scientific activities toward meeting major regulatory milestones in a timely and cost-effective manner. This approach has raised concern among elements of technical, ...

1995-09-03

230

Review of the Vortec soil remediation demonstration program  

Energy Technology Data Exchange (ETDEWEB)

The principal objective of the METC/Vortec program is to develop and demonstrate the effectiveness of the Vortec CMS in remediating soils contaminated with hazardous materials and/or low levels of radionuclides. To convincingly demonstrate the CMS`s capability, a Demonstration Plant will be constructed and operated at a DOE site that has a need for the remediation of contamination soil. The following objectives will be met during the program: (1) establish the glass chemistry requirements to achieve vitrification of contaminated soils found at the selected DOE site; (2) complete the design of a fully integrated soil vitrification demonstration plant with a capacity to process 25 TPD of soil; (3) establish the cost of a fully integrated soil demonstration plant with a capacity to process 25 TPD of soil; (4) construct and operate a fully integrated demonstration plant; (5) analyze all influent and effluent streams to establish the partitioning of ...

1994-12-31

231

Resolving issues at the Department of Energy/Oak Ridge Operations Facilities  

Energy Technology Data Exchange (ETDEWEB)

Waste management, like many other issues, has experienced major milestones. In 1971, the Calvert Cliff's decision resulted in an entirely different approach to the consideration of environmental impact analysis in reactor siting. The accidents at Three Mile Island and Chernobyl have had profound effects on nuclear power plant design. The high-level waste repository program has had many similar experiences that have modified the course of events. The management of radioactive, hazardous chemical and mixed waste in all of the facilities of the Oak Ridge Operations (ORO) Office of the Department of Energy (DOE) took on an entirely different meaning in 1984. On April 13, 1984, Federal Judge Robert Taylor said that DOE should proceed 'with all deliberate speed' to bring the Y-12 plant into compliance with the Resource Conservation and Recovery Act and the Clean Water Act. This ...

1988-01-01

232

Shooting from the HIP: Hyperion's efforts to clean Santa Monica Bay. [Hyperion Improvement Program (HIP)  

Energy Technology Data Exchange (ETDEWEB)

The Outstanding Achievement Award in Water Pollution Control' is intended to recognize the water pollution control program that best demonstrates achieving significant, lasting, and measurable excellence in water-quality improvement in preventing water-quality degradation in a region, basin, or water body. This article is about the 1991 Award. This year, WPCF honored Los Angeles Hyperion Treatment Plant with a citation of outstanding achievement. To qualify for this honor, Hyperion has remarkably improved the quality of wastewater discharged to Santa Monica Bay since 1985. Capital programs developed by Los Angeles to achieve this rapid improvement, coined the Hyperion Improvement Program (HIP), reflect the city's commitment to protect the valuable resource of Santa Monica Bay. The HIP was conceived in 1986 to cease sludge ocean disposal by the end of 1987 and expedite effluent quality improvement before ...

1991-11-01

233

Direct denitration and recycling of PFBR MOX liquid waste from dissolution test using microwave heating method  

International Nuclear Information System (INIS)

Full text: Dissolution test (DT) is one of the important specifications of PFBR MOX fuel. It is a macro homogeneity test used to ascertain that the dissolution of spent fuel will be easier during reprocessing. The DT specification limit for PFBR MOX fuel is ? 1.0 wt.% residue of the whole pellet when it is dissolved in HNO3 under reflux conditions. For this test, sintered MOX pellet is dissolved in reflux condition in 60 ml of 12M HNO3 for 10 hours. This test is carried out for each batch and during complete MOX campaign a lot of MOX waste in liquid form is being generated. This liquid waste is in clean form and U and Pu is required to be recovered from the clean waste. Different methods like direct denitration, precipitation and solvent extraction are available but either the product is not of good quality for pelletization or secondary liquid wastes are generated. Microwave denitration is a faster and ...

2010-11-24

234

Immobilization of waste material  

International Nuclear Information System (INIS)

A method is described for immobilizing or solidifying waste material, which includes blending the waste material with powdered metal and subjecting the mixture of waste material and powdered metal to high pressure. (author).

235

DISPOSING DEVICE FOR WASTE  

J-STORE (Japan)

Full Text Available

2005-12-19

236

Geodynamic program office  

Energy Technology Data Exchange (ETDEWEB)

Program activities and achievements in 1982 of the geodynamic program are summarized. The significant results presented are summarized.

1983-05-01

237

STRESS CORROSION CRACKING SUSCEPTIBILITY OF HIGH LEVEL WASTE TANKS DURING SLUDGE MASS REDUCTION  

Energy Technology Data Exchange (ETDEWEB)

Aluminum is a principal element in alkaline nuclear sludge waste stored in high level waste (HLW) tanks at the Savannah River Site. The mass of sludge in a HLW tank can be reduced through the caustic leaching of aluminum, i.e. converting aluminum oxides (gibbsite) and oxide-hydroxides (boehmite) into soluble hydroxides through reaction with a hot caustic solution. The temperature limits outlined by the chemistry control program for HLW tanks to prevent caustic stress corrosion cracking (CSCC) in concentrated hydroxide solutions will potentially be exceeded during the sludge mass reduction (SMR) campaign. Corrosion testing was performed to determine the potential for CSCC under expected conditions. The experimental test program, developed based upon previous test results and expected conditions during the current SMR campaign, consisted of electrochemical and mechanical testing to determine the ...

2007-10-18

238

European Commission - Environment  

Wastenet

...Species - see CITES Trade of Dangerous Chemicals Transport and Environment U Urban Environment Use of natural resources V Volatile Organic Compounds W Waste Landfills Waste electrical and electronic equipment - see WEEE Waste incineration Waste legislation - reporting Waste management planning Waste oils Waste shipments Waste water - see Urban waste water Water Bathing Water Drinking water Floods Marine environment Urban waste water Water Framework Directive WEEE - Waste Electric and Electronic Equipment Wildlife ...

239

Maintenance implementation plan for solid waste management  

Energy Technology Data Exchange (ETDEWEB)

This Maintenance Implementation Plan (MIP)was developed for implementation of the U.S. Department of Energy (DOE) Order 4330.4A, A Maintenance Implementation Program (DOE 1990) which has been replaced by 4330.4B (DOE 1994) at the Hanford Site SWM complex. It addresses maintenance functions associated with SWM, which includes the field operational group and the facilities operational group. An assessment of the existing maintenance programs for SWM was performed, and the results of this assessment were evaluated to determine corrective actions required to bring Solid Waste Maintenance into compliance with the order. The objective of this MIP is to provide baseline information for the control and execution of SWM Maintenance activities relative to the requirements of Order 4330.4B, Chapter II. (Nuclear Facilities) It also describes actions that are planned to achieve compliance. Section 2.0 of this MIP summarizes the mission, ...

1996-06-27

240

It`s slim with a plain green cover: Australia`s management plan for polychlorinated biphenyls  

Energy Technology Data Exchange (ETDEWEB)

In November 1995, the Australian and New Zealand Environment and Conservation Council (ANZECC, the Council of State and National Environment Ministers) adopted a National Management Plan for PCBs. This was a significant milestone in the very long saga of Australian efforts to develop public policy and management structures for dealing with persistent organochlorine wastes. The author was part of a four-person consultation panel that carried out a public involvement program to assist and inform the process of developing the National Management Plan. The program involved, among other things, visiting every state and territory of Australia at least twice. This paper describes the development and delivery of the public involvement program, including ongoing interactions with Governments. The latter is often a complex (and many would say an unduly complex) matter in the federal system, where primary ...

1996-12-31

241

Status and strategies in radioactive waste management in the Russian Federation  

International Nuclear Information System (INIS)

Full text: There are following general tendencies linking to SNF and radioactive waste management (RWM) in the Russian nuclear industry now. The intention to use the closed nuclear fuel cycle based on power water reactors and fast reactor. The intensification of measures aimed at the solution of 'nuclear legacy' from defenses programs of USSR. The intention to improve the existing national RW management infrastructure in the near years by means of the creation of a centralized national system (including managing corporation responsible for operation of long-storage and disposal facilities of conditioned RW). The main aims radioactive waste management (RWM) in nuclear power plants (NPP) for the next 10-15 years are to equip all NPPs with the necessary set of facilities for conditioning of the stored and currently generated RW with packaging the end-product into containers, to build regional NPPs RW repositories and to ...

242

Review of the WIPP draft application to show compliance with EPA transuranic waste disposal standards  

Energy Technology Data Exchange (ETDEWEB)

The purpose of the New Mexico Environmental Evaluation Group (EEG) is to conduct an independent technical evaluation of the Waste Isolation Pilot Plant (WIPP) Project to ensure the protection of the public health and safety and the environment. The WIPP Project, located in southeastern New Mexico, is being constructed as a repository for the disposal of transuranic (TRU) radioactive wastes generated by the national defense programs. The EEG was established in 1978 with funds provided by the U.S. Department of Energy (DOE) to the State of New Mexico. Public Law 100-456, the National Defense Authorization Act, Fiscal Year 1989, Section 1433, assigned EEG to the New Mexico Institute of Mining and Technology and continued the original contract DE-AC04-79AL10752 through DOE contract DE-AC04-89AL58309. The National Defense Authorization Act for Fiscal Year 1994, Public Law 103-160, continues the authorization. EEG performs ...

1996-03-01

243

Evaluation of the suitability of the WIPP site  

Energy Technology Data Exchange (ETDEWEB)

Determination of the suitability of the site for WIPP is only the first major phase in the evaluation of the radiological impact of the repository on the public health and safety. The Environmental Evaluation Group (EEG) will continue to independently review the design of the facility, the operational procedures, the criteria for packaging and shipment of the waste, the plans, procedures and results of the WIPP experiments, emergency preparedness, adherence to EPA and pertinent NRC regulations, and other important features of the project. EEG has concluded from existing evidence that the Los Medanos site for the WIPP project has been characterized in sufficient detail to warrant confidence in the validation of the site for the permanent emplacement of approximately 6 million cubic feet of defense transuranic waste. This conclusion is based on the assumption that the maximum surface dose rate for the unshielded remote-handled transuranic ...

1983-05-01

244

Geothermal materials program: strategy. Final report  

Energy Technology Data Exchange (ETDEWEB)

The following topics are discussed: program goal and objectives, program organization, and program status. Current program projects are described. (MHR)

1980-10-01

245

Subsurface Injection of Liquid Waste  

Science.gov (United States)

... Other Sources Toxics Intranet Subsurface Injection of Liquid Waste -- Florida Surface features of a typical...

247

Radiation protection and the management of radioactive waste in the oil and gas industry  

CERN Document Server

Radiation protection and the management of radioactive waste in the oil and gas industry

2003-01-01

249

On-site burning, remote camp  

Science.gov (United States)

... wood, kitchen wastes, and human faeces. The ash from such waste burning shall be deposited and ...

250

Liquid Radioactive Wastes Processing  

International Science & Technology Center (ISTC)

Methods of Decontamination, Utilization, and Deactivation of Liquid Radioactive Wastes

251

IEE, accelerated waste mgt, McM  

Science.gov (United States)

... in ATCM Recommendation XIV-2. The USAP's materials and waste management efforts are consistent with ...

252

Human Waste Handling-Kooyman  

Science.gov (United States)

... wood, kitchen wastes, and human faeces with the ash from such burning deposited and retained in an ...

253

Dioxins in the Baltic sea  

Wastenet

for municipal waste iron ore sinter plants incinerators for clinical waste facilities of the non-ferrous metal

254

Combustion of Crop Production Wastes  

International Science & Technology Center (ISTC)

Development, Investigation and Improvement of a System of Incinerating Crop Production Wastes in Small Capacity Boilers

256

Responses to comments received on the draft final report of the Secretary of Energy Advisory Board Task Force on Radioactive Waste Management  

Energy Technology Data Exchange (ETDEWEB)

The Task Force solicited comments on its Draft Final Report from a variety of sources. Letters were sent to over 400 individuals who had expressed interest in the interest in the Department`s radioactive waste, management programs, a notice was placed in the Federal Register, the morning session of the January 1993 meeting of the full Secretary of Energy Advisory Board was given over to discussion of the draft, and Task Force members and staff presented the effort at several professional meetings. Altogether 32 written comments were received. They are reproduced here, followed in each case by the Task Force`s response to specific suggestions made to improve the draft. (The panel did not respond to comments that simply reflected policy preferences or that praised the group`s effort.) With one exception, those specific suggestions are highlighted and given a letter designation from {open_quotes}A{close_quotes} to {open_quotes}Z{close_quotes}. The ...

1994-10-01

257

Registration of Hanford Site Class V underground injection wells  

Energy Technology Data Exchange (ETDEWEB)

This document was requested by the Washington State Department of Ecology. Based on the State Underground Injection Control Program, as described in the Washington Administrative Code, French drains and reverse wells are being registered as Class V wells. Information on out-of-service French drains, out-of-service reverse wells, and out-of-service cribs that are deeper than their largest surface dimension is also provided. The data for this submittal were taken from the Waste Information Database System (WIDS) and the Hanford Environmental Compliance Record (HECR) database. The current definition used in WIDS for an ''inactive facility'' is one that either no longer receives waste or plans to in the future. The facilities listed in WIDS as inactive have all been listed as ''out-of-service.'' Information concerning the deactivation method for a facility ...

1988-05-01

258

Paul Scherrer Institute Scientific Report 1998. Volume IV: Nuclear Energy and Safety  

Energy Technology Data Exchange (ETDEWEB)

Nuclear energy related research in Switzerland is concentrated at PSI`s Nuclear Energy and Safety Research Department (NES). The total effort invested in nuclear energy research in 1998 amounted to about 195 py/a and 4.5 millions CHF of investment and maintenance costs. Approximately half of the salary, investment and maintenance costs are externally funded, primarily by the Swiss Utilities, the national co-operative for the disposal of nuclear waste (NAGRA), the Federal Office of Energy (BFE) through the nuclear safety inspectorate (HSK) and the Federal Office for Science and Education (BBW) in connection with the EC Framework Programmes; an increasing part of external funding is coming from domestic and foreign industry (nuclear component and fuel suppliers). The activities of the department are concentrated on three main domains of: Safety and related problems of operating plants; safety features of future reactor and fuel cycles; waste ...

1999-09-01

259

NICE3: Dyebath reuse in carpet manufacturing  

Energy Technology Data Exchange (ETDEWEB)

Fact sheet on an analysis system for dyebath processes in the carpet manufacturing industry written for the NICE3 Program. The Georgia Institute of Technology (G.I.T.) has developed an effective automated dyebath analysis and reuse system that improves the energy, environmental, and economic performance of dyehouse batch operations. The new system enables dyeing solutions to be accurately monitored and adjusted for reuse. According to industry estimates, 160 pounds of water are used to produce each pound of textile product. The current wasteful batch dyeing process requires all water and residual chemicals, as well as the energy required to heat the mixture for dyeing, to be dumped after one application. Spent dyebaths can only be reused after they are sampled, analyzed, and reconstituted, a process requiring labor and expertise that are unavailable in the dyehouses. Therefore, successful commercial reuse depends on an automated analysis system ...

1999-09-29

260

Matching the needs of a nation: The strategic roles of indicators for decisionmaking  

Energy Technology Data Exchange (ETDEWEB)

Indicators are important tools for communicating and making accessible scientific and technical information to policymakers and the general public. They therefore play an important role in transforming information into action. Worldwide, many initiatives are underway to construct indicators for a variety of purposes, including those for reporting on sustainable development. This paper briefly describes the attempts made so far, but stresses that the users of the indicators should play a greater role in indicator construction. In developing countries, a substantial lack of data has meant that specific policy formulation may develop without adequate technical input. In developed countries also, data gaps may hinder policy formulation, implementation, and evaluation. However, the development of indicators as tools to assist in the management of hazardous wastes and toxic chemicals is still in the early stages of formulation. A more imaginative ...

1996-12-31

261

Development program for magnetically assisted chemical separation: Evaluation of cesium removal from Hanford tank supernatant  

International Nuclear Information System (INIS)

Magnetic particles (MAG*SEP"S"M) coated with various absorbents were evaluated for the separation and recovery of low concentrations of cesium from nuclear waste solutions. The MAG*SEP"S"M particles were coated with (1) clinoptilolite, (2) transylvanian volcanic tuff, (3) resorcinol formaldehyde, and (4) crystalline silico-titanate, and then were contacted with a Hanford supernatant simulant. Particles coated with the crystalline silico-titanate were identified by Bradtec as having the highest capacity for cesium removal under the conditions tested (variation of pH, ionic strength, cesium concentration, and absorbent/solution ratio). The MAG*SEP"S"M particles coated with resorcinol formaldehyde had high distribution ratios values and could also be used to remove cesium from Hanford supernant simulant. Gamma irradiation studies were performed on the MAG*SEP"S"M particles with a gamma dose equivalent to 100 cycles of use. This irradiation decreased the loading ...

1994-05-09

262

Design for environment for the National Ignition Facility  

Energy Technology Data Exchange (ETDEWEB)

The National Ignition Facility (NIF) will be a U.S. Department of Energy (DOE) national center for inertial confinement fusion (ICF) and other research into the physics of high temperatures and high densities, and a vital element of the DOE`s nuclear weapons Stockpile Stewardship and Management Program. It will be used by scientists from a numerous different institutions and disciplines to support research advancements in national security, energy, basic science, and economic development. Multiple powerful laser beams will `ignite` small fusion targets, helping liberate more energy than is required to initiate the fusion reactions. This paper discusses the Design for Environment process for NIF, some of the subsequent activities resulting from the initial study, and a few of the lessons learned from this process. Subsequent activities include the development of a Pollution Prevention and Waste Minimization Plan (P2/WMin) for the facility, which ...

1998-05-01

263

Chemical contaminants on DOE lands and selection of contaminant mixtures for subsurface science research  

Energy Technology Data Exchange (ETDEWEB)

This report identifies individual contaminants and contaminant mixtures that have been measured in the ground at 91 waste sites at 18 US Department of Energy (DOE) facilities within the weapons complex. The inventory of chemicals and mixtures was used to identify generic chemical mixtures to be used by DOE's Subsurface Science Program in basic research on the subsurface geochemical and microbiological behavior of mixed contaminants (DOE 1990a and b). The generic mixtures contain specific radionuclides, metals, organic ligands, organic solvents, fuel hydrocarbons, and polychlorinated biphenyls (PCBs) in various binary and ternary combinations. The mixtures are representative of in-ground contaminant associations at DOE facilities that are likely to exhibit complex geochemical behavior as a result of intercontaminant reactions and/or microbiologic activity stimulated by organic substances. Use of the generic mixtures will focus research ...

1992-04-01

264

Base Program on Energy Related Research: Quarterly report, August 1-October 31, 1994  

Energy Technology Data Exchange (ETDEWEB)

This document describes research performed at the Morgantown Energy Technology Center in the areas of oil and gas, advanced systems application, environmental technologies, applied energy science and remediation. The following subtasks are described: CROW{sup TM} Process Modeling, Development of a Portable Data Acquisition System and Coalbed Methane Simulator, Tank Bottom Waste Processing using the TaBoRR{sup TM} Process, Process Support and Development, Eastern Shale Oil Residue as an Asphalt Additive, Solid Waste Management, Remediation of Contaminated Soils, The Syn-Ag{sup TM} Process: Coal Combustion Ash Management Option, the Maxi-Acid{sup TM} Process: In- sit Amelioration of Acid Mine Drainage, Spill Test Facility Database, Heavy Oil/Plastics Co-Processing, Fossil Fuel and Hydrocarbon Conversion Using Hydrogen-Rich Plasmas, and North Site Remediation.

1994-12-31

265

Transuranic contaminated waste form characterization and data base  

Energy Technology Data Exchange (ETDEWEB)

This volume contains 5 appendices. Title listing are: technologies for recovery of transuranics; nondestructive assay of TRU contaminated wastes; miscellaneous waste characteristics; acceptance criteria for TRU waste; and TRU waste treatment technologies.

1980-07-01

266

Process Waste Assessment for inorganic solid waste and empty containers <30 gallons  

Energy Technology Data Exchange (ETDEWEB)

This Process Waste Assessment was conducted to evaluate the two largest hazardous waste streams generated on-site at Sandia National Laboratory (SNL)/California -- ``Other Inorganic Solid Waste`` and ``Empty Containers <30 Gallons.``

1993-12-01

267

LAW ON WASTE MANAGEMENT  

Wastenet

1 to the operator of a waste collective system by an agreement or contract. The conditions for the ...Fees of the waste collective system are subject to the supervision of the authority responsible for market surveillance. ...The operator of waste collection system collects wastes from producers and holder and transports these to a collection

268

Wetlands and water quality: EPA's (Environmental Protection Agency's) research and monitoring implementation plan for the years 1989-1994  

Energy Technology Data Exchange (ETDEWEB)

This document describes products which the US EPA Wetlands Research Program proposes to develop during the years 1989-1994. The general protocols used to develop these products are also described. All these products are intended to address concerns about the wetlands and water quality, and are part of a larger set of products EPA is developing to deal with other aspects of wetlands. EPA's highly interrelated concerns about wetlands and water quality can be generally categorized as follows: water quality criteria to protect wetland function; ecological status of the wetland resource; and waste-assimilation limits of wetlands.

1989-04-01

269

Status of safety at Areva group facilities. 2007 annual report; Areva, etat de surete des installations nucleaires. Rapport annuel 2007  

Energy Technology Data Exchange (ETDEWEB)

This report describes the status of nuclear safety and radiation protection in the facilities of the AREVA group and gives information on radiation protection in the service operations, as observed through the inspection programs and analyses carried out by the General Inspectorate in 2007. Having been submitted to the group's Supervisory Board, this report is sent to the bodies representing the personnel. Content: 1 - A look back at 2007 by the AREVA General Inspector: Visible progress in 2007, Implementation of the Nuclear Safety Charter, Notable events; 2 - Status of nuclear safety and radiation protection in the nuclear facilities and service operations: Personnel radiation protection, Event tracking, Service operations, Criticality control, Radioactive waste and effluent management; 3 - Performance improvement actions; 4 - Description of the General Inspectorate; 5 - Glossary.

2007-07-01

270

Research and development environmental activities at CANMET; Les activites environnementales de R et D chez CANMET  

Energy Technology Data Exchange (ETDEWEB)

The Canada Centre for Mineral and Energy Technology (CANMET) is a research organization dedicated to the advancement of the Canadian mining industry. It specializes in the development of new technologies and the coordination of scientific partnerships in the fields of mines, metallurgical processes, and the environment. CANMET supports a number of research and development activities related to the mining industry. In this poster presentation, the author described the mandate of CANMET by first introducing the organization chart with a special emphasis placed on the Mining and Mineral Sciences Laboratories. A description of the different types of partnerships was included, followed by specific details concerning all the projects related to the mining industry, such as terrain control, automation of mines, underground mining environment, processes and services, analytical support, environmental programs, mine effluent, waste rock and tailings, ...

2000-07-01

271

Reconnaissance radiological characterization for the White Point Nike Missile Site, San Pedro, California  

International Nuclear Information System (INIS)

This report is the result of field work performed at the former White Point Nike Missile Site, San Pedro, California. The Hazardous Waste Remedial Actions Program tasked the Oak Ridge National Laboratory Pollutant Assessments Group in Grand Junction, Colo., with this project. The objective was to determine whether or not radioisotopes possibly associated with past Department of Defense (DOD) operations were present and within accepted background levels. The radiation survey was accomplished by performing three independent radiation surveys, both outdoors and indoors, and random soil sampling. Initially, the site was land surveyed to develop a grid block system. A background radiation investigation was performed out in the San Pedro area.

272

Preliminary assessment of the modular block power plant concept  

Energy Technology Data Exchange (ETDEWEB)

Adding capacity to coal-fired plants in small increments of an overall integrated program may be the solution to the 10-year lead time required for the construction of a new plant. A preliminary study evaluates the technical and economic feasibility of a modular natural gas and coal-fired combined-cycle power plant which can be installed in three distinct phases. The plant sizes are suitable for large industrial and utility applications. The Modular Block Power Plant (MBPP) concept offers the advantages of phase construction, lower capital cost, lower cost electricity, lower air emissions, lower water requirements, and reduced solid waste discharge. Other advantages include part load availability, reduced coal inventory requirements, and easier plant siting. 11 figures, 4 tables.

1984-01-01

273

Impact of ocean pollution  

Energy Technology Data Exchange (ETDEWEB)

Man's wastes are polluting the oceans from various sources and delivered by various routes. The result has been the loss of habitat and the irreversible altering of marine ecosystems. Development in the coastal zones and offshore activities that disrupt biologically sensitive areas have led to international negotiations to regulate these impacts and develop a law of the sea. Basic to international cooperation, however, is the need to develop answers to questions about the ecological consequences of development programs and the carrying capacity of the oceans. Current information does not demonstrate long-term global impacts, making it difficult to detect and predict incremental changes and causal relationships. Society needs to determine how much environmental damage it will accept and then to develop appropriate technology, such as biomonitoring. Society also needs to reexamine its positions on technology-based regulatory controls to ...

1981-03-01

274

Application of hydro-geochemical simulator to the issues on geological environment  

International Nuclear Information System (INIS)

Recently, it has become clear that the chemical circumstances under which long-term geological evolution occurs must be properly evaluated in order to develop effective remediation programs for contaminated soil, landfills, radioactive waste repositories, and carbon dioxide capture and storage. The issue of acidic leakage from excavated rock stuck was assessed using a hydro-geochemical simulator, TOUGHREACT. We concluded that in order to properly investigate the phenomenon of acidic leakage from excavated pyrite-containing rock stuck, it is important to obtain accurate information about the following factors: intensity of rainfall, unsaturated flow properties of the excavated rock stuck, specific surfaces for oxidation reaction of pyrite, the species and the quantity of other minerals contained in the rock, and secondary minerals produced. (author)

275

Waste management units - Savannah River Site. Volume 1, Waste management unit worksheets  

Energy Technology Data Exchange (ETDEWEB)

This report is a compilation of worksheets from the waste management units of Savannah River Plant. Information is presented on the following: Solid Waste Management Units having received hazardous waste or hazardous constituents with a known release to the environment; Solid Waste Management Units having received hazardous waste or hazardous constituents with no known release to the environment; Solid Waste Management Units having received no hazardous waste or hazardous constituents; Waste Management Units having received source; and special nuclear, or byproduct material only.

1989-10-01

276

A numerical method for determining radon diffusion coefficient through buffer materials from low-level radwaste disposal site  

Energy Technology Data Exchange (ETDEWEB)

The diffusion coefficient of radioactive radon (Rn) through buffer materials from low-level radwaste disposal site was determined in this present study by measuring the time-dependent diffusion of radon through a thin slab of the material. The diffusion process was required to reach a steady state so as to obtain a good estimate of the diffusion coefficient. A numerical method using the nonlinear least-squares and Marquardt`s method (NLSM method) was proposed for characterizing the diffusion coefficient of Rn so as to determine whether the process has reached steady-state or not. Natural mordenite, a potential buffer material of LLW disposal facility, was selected as testing porous material. The NLSM method was shown by the results to be able to estimate the diffusion coefficient even if the process was in transient period. Additionally, this method was also demonstrated to agree well with the results by the conventional method while the process has already reached ...

1994-12-31

277

Tiger Team assessment of the Brookhaven National Laboratory  

Energy Technology Data Exchange (ETDEWEB)

This report documents the results of the Department of Energy's (DOE's) Tiger Team Assessment conducted at Brookhaven National Laboratory (BNL) in Upton, New York, between March 26 and April 27, 1990. The BNL is a multiprogram laboratory operated by the Associated Universities, Inc., (AUI) for DOE. The purpose of the assessment was to provide the status of environment, safety, and health (ES H) programs at the laboratory. The scope of the assessment included a review of management systems and operating procedures and records; observations of facility operations; and interviews at the facilities. Subteams in four areas performed the review: ES H, Occupational Safety and Health, and Management and Organization. The assessment was comprehensive, covering all areas of ES H activities and waste management operations. Compliance with applicable Federal, State, and local regulations; applicable DOE Orders; and internal BNL ...

1990-06-01

278

Programmed improvements of the alternating gradient synchrotron complex at Brookhaven National Laboratory, Upton, New York. Environmental assessment  

Energy Technology Data Exchange (ETDEWEB)

The purpose and need for DOE to undertake the actions described in this document are to improve the efficiency of the Alternating Gradient Synchrotron (AGS) complex. Benefits would include optimization of the AGS scientific program, increased high-energy and nuclear physics experimentation, improved health and safety conditions for workers and users, reduced impact on the environment and the general public, energy conservation, decreased generation of hazardous and radioactive wastes, and completion of actions required to permit the AGS to be the injector to the Relativistic Heavy Ion Collider (RHIC)., Improved efficiency is defined as increasing the AGS`s capabilities to capture and accelerate the proton intensity transferred to the AGS from the AGS booster. Improved capture of beam intensity would reduce the beam losses which equate to lost scientific opportunity for study and increased potential for radiation doses to workers and the general ...

1994-03-01

279

Optimization of productivity of mining equipment systems  

Energy Technology Data Exchange (ETDEWEB)

The operation of equipment in a mine produces a complex system which requires monitoring, simulation, analysis and reconciliation to ensure optimum production. The work described in the paper represents the initial steps in an overall program to enable optimization of production and equipment usage. Two areas of investigation are covered in some detail. The first concerns large haul trucks which accomplish much of the movement of minerals and wastes in many open pit mining operations. The monitoring of trucks in normal operation is described along with some of the results of such work. The second concerns draglines which are similarly important in moving overburden in many coal mines. A program of computer simulation of draglines is described. This shows the benefits of a simulation model which can be used to determine the effects of productivity of small changes in stripping procedure or dragline characteristics. The above ...

1983-05-01

280

Office of Industrial Technologies: Summary of program results  

Energy Technology Data Exchange (ETDEWEB)

Working in partnership with industry, the US Department of Energy`s (DOE`s) Office of Industrial Technologies (OIT) is helping reduce industrial energy use, emissions, and waste while boosting productivity. Operating within the Office of Energy Efficiency and Renewable Energy (EE), OIT conducts research, development, demonstration, and technology transfer efforts that are producing substantial, measurable benefits to industry. This document summarizes some of the impacts of OIT`s programs through 1997. OIT tracks energy savings as well as other benefits associated with the successfully commercialized technologies resulting from OIT-supported research partnerships. Specifically, a chart shows current and cumulative energy savings as well as cumulative reductions of various air pollutants including particulates, volatile organic compounds (VOCs), nitrogen oxides (NO{sub x}), sulfur oxides (SO{sub x}), and the greenhouse gas, carbon dioxide ...

1999-01-01

281

Maintenance implementation plan for the B Plant/WESF. Revision 4  

Energy Technology Data Exchange (ETDEWEB)

This Maintenance Implementation Plan (MIP) has been developed for maintenance functions associated with the B Plant/WESF (Waste Encapsulation Storage Facility) complex. The objective of this plan is to provide baseline information for establishing and identifying WHC conformance programs and policies applicable to implementation of DOE order 4330.4B guidelines. In addition, this maintenance plan identifies the actions necessary to develop a cost-effective and efficient maintenance program at B Plant/WESF. The B Plant WESF facility complex consists of three main facilities and several support structures located in the 200 East Area of the Hanford site. B Plant is a transition facility that is required to ensure safe storage and management of WESF (operating facility) cesium and strontium capsules. B Plant/WESF also contains substantial radiological inventory from previous campaigns. There are no production activities at B ...

1996-01-01

282

Labor market trends for nuclear engineers through 2000  

Energy Technology Data Exchange (ETDEWEB)

Throughout most of the 1980s, both private organizations and government agencies were concerned about the availability of an adequate supply of qualified nuclear engineers. This concern was primarily the result of a number of nuclear engineering academic programs being eliminated coupled with a continuous decline in graduate and undergraduate enrollments and degrees. By the early 1990s, the number of degrees and available supply had declined to new lows, but cutbacks in funding for the nuclear weapons program and nuclear energy R&D, and in hiring by the electric utility industry, offset in large measure the declining supply. Recently, concerns about environment and waste management and about nuclear safety have again generated questions about the adequacy of supply of qualified personnel for nuclear energy activities. This report briefly examines the nuclear engineering labor market. Trends in employment, new graduates, ...

1995-01-01

283

Implementation of the DOE Office of Technology Development Strategic Program Plan for Environmental Education and Development  

Energy Technology Data Exchange (ETDEWEB)

With the November 1989 formation of the Office of Technology Development (OTD) within the Office of Environmental Restoration and Waste Management (EM) came the responsibility to develop programs to ensurethat enough trained and educated people would be available to support the achievement of EM's 30-year goal. This mission responsibility derives from public policy and Departmental environmental management requirements. Within DOE, urgency to move forward resulted from the assumptions (1) that the current workforce was insufficiently prepared for the transition from a production mission to a mission of environmental compliance and cleanup; and (2) that, given current trends and forecasts, the national education infrastructure was unlikely to yield the scientists, engineers, and technicians to meet future DOE workforce needs, especially in the case of women and minorities who, projected to make up two-thirds of the net entering ...

1992-01-01

284

CANMET's environmental and process research on uranium  

International Nuclear Information System (INIS)

Environmental research related to uranium tailings is being carried out within the Mining Research Laboratories and Mineral Sciences Laboratories of CANMET, EMR. Field-related research on uranium tailings has been conducted at Elliot Lake for over five years. Much of the work has been focused on a program to rehabilitate pyritic tailings. This has resulted in developing a practicable technology for growing vegetation on such wastes. Limitations have been small size of the test-plots and the relatively short period during which experiments have been carried out. A research program aimed at identifying and reducing acidic and radioactive effluents is also underway at Elliot Lake. These liquid effluents have been identified as the most serious threat to the environment. Research at the Mineral Sciences Laboratories and its predecessor divisions relating to the processing of uranium and thorium ores is outlined. A process has ...

285

Biomass research program of the USDA Southern Agricultural Energy Center  

Energy Technology Data Exchange (ETDEWEB)

The biomass research program of the USDA, Southern Agricultural Energy Center is conducted at several locations throughout the United States. A portion of the research is directed toward improved systems to harvest, process and store biomass so that the energy density will be enhanced. Other research projects deal with: conversion and utilization of animal wastes in integrated energy-food production systems, including the production of liquid fuel and feed byproducts; producing low BTU gas to be utilized in internal combustion engines, including the system for continuous feeding of the gasifier; direct combustion of biomass for thermal energy; gasifying biomass so that the products of combustion can pass through a crop being dried without leaving deleterious residues; small scale systems for on-farm expelling of vegetable oil; and studies on the use of vegetable oils for diesel fuel substitutes. In summary, the low energy density of biomass ...

1982-08-01

286

A corporate social responsibility initiative in the field of nuclear power  

International Nuclear Information System (INIS)

Societatea Nationala Nuclearelectrica SA is the operator of the Cernavoda nuclear power plant and the second largest energy producer in Romania, after Hidroelectrica, ensuring 18% of the internal energy demand. The production of nuclear power differs from other industrial activities through the risks it involves and through the legacy it leaves to the future generations, i.e. the nuclear waste. Taking into account these considerations, public acceptance represents a constant preoccupation for nuclear companies around the world. Corporate Social Responsibility (CSR) is a new practice in the nuclear industry. After a long tradition of involvement in the life of the local community through the Social Program for Cernavoda, Nuclearelectrica has initiated a CSR campaign with the theme 'Welcome a tree in your family', addressed to pupils and high school students from Cernavoda. By this campaign, we aimed at creating relevance, not just green lots and ...

2009-10-12

287

Project SAFE. Update of the SFR-1 safety assessment. Phase 1. Appendix A1: Inventory  

Energy Technology Data Exchange (ETDEWEB)

One of the aims in the safety assessment of SFR-1 is to estimate the release to the environment. In order to make these calculations there is a need to describe the inventory in greater detail. The new computerised database of waste in SFR-1 gives a good possibility to achieve this. The aim for project SAFE is to make both conservative and realistic radionuclide transport calculations. To achieve this goal there must be two inventories. The conservative inventory is the inventory used in the design of the repository, which in most parts is identical with the limits in the licence for SFR-1. There is a great interest to have good estimates of the volumes of the different waste types. A thorough prognosis should be made in 1999, but until then the latest one from 1995 could be used in the calculations. The total (actual) inventory of nuclides is calculated from the measurements of the easy-to-measure nuclides since, in principle, all ...

1998-10-01

288

Carbon Bed Mercury Emissions Control For Mixed Waste Treatment  

International Nuclear Information System (INIS)

Mercury has had various uses in nuclear fuel reprocessing and other nuclear processes, and so is often present in radioactive and mixed (both radioactive and hazardous according to the Resource Conservation and Recovery Act) wastes. Depending on regulatory requirements, the mercury in the off-gas must be controlled with sometimes very high efficiencies. Compliance to the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards can require off-gas mercury removal efficiencies up to 99.999% for thermally treating some mixed waste streams. Several test programs have demonstrated this level of off-gas mercury control using fixed beds of granular sulfur-impregnated activated carbon. Other results of these tests include: (a) The depth of the mercury control mass transfer zone was less than 15-30 cm for the operating conditions of these tests, (b) MERSORB(reg_sign) carbon can sorb ...

2010-11-01

289

Energy Conversion and Storage Program: 1992 Annual report  

Energy Technology Data Exchange (ETDEWEB)

This report is the 1992 annual progress report for the Energy Conversion and Storage Program, a part of the Energy and Environment Division of the Lawrence Berkeley Laboratory. Work described falls into three broad areas: electrochemistry; chemical applications; and materials applications. The Energy Conversion and Storage Program applies principles of chemistry and materials science to solve problems in several areas: (1) production of new synthetic fuels, (2) development of high-performance rechargeable batteries and fuel cells, (3) development of advanced thermochemical processes for energy conversion, (4) characterization of complex chemical processes and chemical species, and (5) study and application of novel materials for energy conversion and transmission. Projects focus on transport-process principles, chemical kinetics, thermodynamics, separation processes, organic and physical chemistry, novel materials, and advanced methods of ...

1993-06-01

290

Waste management at Los Alamos: Protecting our environment  

Energy Technology Data Exchange (ETDEWEB)

This report consists of a broad overview of activities at Los Alamos National Laboratory (LANL). The following topics are discussed: The growth of the waste management group; what we do today; the mission of the waste management group; the liquid waste treatment section; the radioactive liquid waste project office; the chemical waste section; the radioactive waste section; and the technical support section.

1993-11-01

291

Radioactive waste  

Energy Technology Data Exchange (ETDEWEB)

The paper deals with the disposal of radioactive waste and the plans for dealing with solid wastes of intermediate and low levels of activity, which are the responsibility of NIREX. NIREX is an executive body which co-ordinates the waste-disposal plans of the main radioactive waste producers. The disposal routes for the active wastes are described including the deep disposal of wastes containing material that will remain active for thousands of years. Requirements for deep burial are outlined with reference to the geology and hydrogeology of the site. Monitoring, maintenance and surveillance are mentioned for the protection of the public.

1984-02-01

292

Multicriteria decision methodology for selecting technical alternatives in the Mixed Waste Integrated Program  

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy (DOE) Mixed Waste Integrated Program (MWIP) has as one of its tasks the identification of a decision methodology and key decision criteria for the selection methodology. The aim of a multicriteria analysis is to provide an instrument for a systematic evaluation of distinct alternative projects. Determination of this methodology will clarify (1) the factors used to evaluate these alternatives, (2) the evaluator`s view of the importance of the factors, and (3) the relative value of each alternative. The selected methodology must consider the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) decision-making criteria for application to the analysis technology subsystems developed by the DOE Office of Technology Development. This report contains a compilation of several decision methodologies developed in various national laboratories, institutions, and universities. The purpose of these ...

1993-11-01

293

Intelligent Extruder  

Energy Technology Data Exchange (ETDEWEB)

''Intelligent Extruder'' described in this report is a software system and associated support services for monitoring and control of compounding extruders to improve material quality, reduce waste and energy use, with minimal addition of new sensors or changes to the factory floor system components. Emphasis is on process improvements to the mixing, melting and de-volatilization of base resins, fillers, pigments, fire retardants and other additives in the :finishing'' stage of high value added engineering polymer materials. While GE Plastics materials were used for experimental studies throughout the program, the concepts and principles are broadly applicable to other manufacturers materials. The project involved a joint collaboration among GE Global Research, GE Industrial Systems and Coperion Werner & Pleiderer, USA, a major manufacturer of compounding equipment. Scope of the ...

2003-04-24

294

Calendar year 1993 groundwater quality report for the Chestnut Ridge Hydrogeologic Regime Y-12 Plant, Oak Ridge, Tennessee. 1993 Groundwater quality data interpretations and proposed program modifications  

Energy Technology Data Exchange (ETDEWEB)

This groundwater quality report (GWQR) contains an evaluation of the groundwater quality data obtained during the 1993 calendar year (CY) at several hazardous and non-hazardous waste management facilities associated with the US DOE Y-12 Plant located on the DOE Oak Ridge Reservation (ORR) southeast of Oak Ridge, Tennessee. The groundwater quality data are presented in Part 1 of the GWQR submitted by Martin Marietta Energy Systems, Inc. to the Tennessee Department of Environment and Conservation (TDEC) in February 1994. Groundwater quality data evaluated in this report were obtained at several hazardous and non-hazardous waste management sites located within the Chestnut Ridge Hydrogeologic Regime (Chestnut Ridge Regime). The Chestnut Ridge Regime encompasses a section of Chestnut Ridge south of the Y-12 Plant and is one of three hydrogeologic regimes defined for the purposes of groundwater quality monitoring at the plant. The Environmental ...

1994-09-01

295

Regional assessment of nonforestry related biomass resources: Virginia  

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing on a county by county basis the agricultural crop, agricultural wastes, municipal wastes, and industrial wastes of Virginia that are potential biomass energy sources.

1988-11-01

296

Regional assessment of nonforestry related biomass resources: Florida  

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing in a county by county manner the agricultural crop, agricultural wastes, municipal wastes and industrial wastes in Florida that are potential biomass energy sources.

1988-11-01

297

Regional assessment of nonforestry related biomass resources: Alabama  

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing on a county by county basis the agricultural crop, agricultural wastes, municipal wastes and industrial wastes of Alabama that are potential biomass energy sources.

1988-11-01

298

Department of the  

Wastenet

Waste Technology and Innovation Study Final Report ...Waste Technology and Innovation Study Final Report 21/18569/150554 ...Survey of waste and resource recovery related technology and innovation, including products and product uses

299

Results of 1995 characterization of Gunite and Associated Tanks at Oak Ridge National Laboratory, Oak Ridge, Tennessee  

Energy Technology Data Exchange (ETDEWEB)

This technical memorandum (TM) documents the 1995 characterization of eight underground radioactive waste tanks at Oak Ridge National Laboratory (ORNL). These tanks belong to the Gunite and Associated Tanks (GAAT) operable unit, and the characterization is part of the ongoing GAAT remedial investigation/feasibility study (RI/FS) process. This TM reports both field observations and analytical results; analytical results are also available from the Oak Ridge Environmental Information System (OREIS) data base under the project name GAAT (PROJ-NAME = GAAT). This characterization effort (Phase II) was a follow-up to the {open_quotes}Phase I{close_quotes} sampling campaign reported in Results of Fall 1994 Sampling of Gunite and Associated Tanks at the Oak Ridge National Laboratory, Oak Ridge, Tennessee, ORNL/ER/Sub/87-99053/74, June 1995. The information contained here should be used in conjunction with that in the previous TM. The sampling plan is documented in ORNL ...

1996-02-01

300

Key Performance Criteria Affecting the Most the Safety of a Nuclear Waste Long Term Storage : A Case Study Commissioned by CEA  

Energy Technology Data Exchange (ETDEWEB)

As part of the work scope set in the French law on high level long lived waste R&D passed in 1991, CEA is conducting a research program to establish the scientific basis and assess the feasibility of long term storage as an option for the safe management of nuclear waste for periods as long as centuries. This goal is a significant departure from the current industrial practice where storage facilities are usually built to last only a few decades. From a technical viewpoint such an extension in time seems feasible provided care and maintenance is exercised. Considering such long periods of time, the risk for Society of loosing oversight and control of such a facility is real, which triggers the question of whether and how long term storage safety can be actually achieved. Therefore CEA commissioned a study (1) in which MUTADIS Consultants (2) and CEPN (3) were both involved. The case study looks into several past and ...

2003-02-24

301

Hanford Site pollution prevention progress report  

Energy Technology Data Exchange (ETDEWEB)

The Richland Operations Office (RL) and Office of River Protection (ORP) are pleased to issue the attached Pollution Prevention Progress Report. We have just met the most aggressive waste reduction and A recycling goals to date and are publishing this report to recognize A the site's progress, and to ensure it will sustain success beyond 1 Fiscal Year 2000. This report was designed to inform the been made by RL and ORP in Waste Minimization (WMin) and Pollution Prevention (P2). RL, ORP and their contractors are committed to protecting the environment, and we reiterate pollution prevention should continue to be at the forefront of the environmental cleanup and research efforts. As you read the attached report, we believe you will see a clear demonstration of RL and ORP's outstanding performance as it has been responsible and accountable to the nation, its employees, and the community in which we live and work. commitment that ...

1999-10-05

302

DARPA Program Composition for Embedded Systems (PCES) ...  

Science.gov (United States)

... Title : DARPA Program Composition for Embedded Systems (PCES) Program Capstone Demonstration Video (Postprint) (CD-ROM). ...

2005-09-01

303

Geothermal Technologies Program: News  

Science.gov (United States)

and Renewable Energy EERE Home | Programs & Offices | Consumer Information Geothermal Technologies Program Search Search Help Geothermal Technologies Program HOME ABOUT...

2011-08-21

305

EERE: Geothermal Technologies Program Home Page  

Science.gov (United States)

and Renewable Energy EERE Home | Programs & Offices | Consumer Information Geothermal Technologies Program Search Search Help Geothermal Technologies Program HOME ABOUT...

2011-08-21

306

Emplacement technology for the direct disposal of spent fuel into deep vertical boreholes  

International Nuclear Information System (INIS)

In the early sixties it was decided to investigate salt formations on its suitability to host heat generating radioactive waste in Germany. In the reference repository concept consequently the emplacement of vitrified waste canisters in deep vertical boreholes inside a salt mine was considered whereas spent fuel should be disposed of in self shielding casks (type POLLUX) in horizontal drifts. The POLLUX casks, 65 t heavy carbon steel casks, will be laid down on the floor of a horizontal drift in one of the disposal zones to be constructed in the salt dome at the 870 m level. The space between casks and drift walls will be backfilled with crushed salt. The transport, the handling und the emplacement of POLLUX casks were subject of successfully performed demonstration and in situ tests in the nineties and resulted in an adjustment of the atomic law. The borehole disposal concept comprises the emplacement of unshielded canisters with vitrified HLW ...

2008-09-01

307

Waste management plan for the APT  

Energy Technology Data Exchange (ETDEWEB)

This revision of the APT Waste Management Plan details the waste management requirements and issues specific to the APT plant for design considerations, construction, and operation. The APT Waste Management Plan is by its nature a living document and will be reviewed at least annually and revised as required.

1997-08-22

310

Nuclear waste management: a perspective  

Energy Technology Data Exchange (ETDEWEB)

The scope of our problems with nuclear waste management is outlined. Present and future inventories of nuclear wastes are assessed for risk. A discussion of what is presently being done to solve waste management problems and what might be done in the future are presented. (DC)

1980-01-01

313

E-waste hazard: The impending challenge  

UK PubMed Central (United Kingdom)

Electronic waste or e-waste is one of the rapidly growing problems of the world. E-waste comprises of a multitude of components, some containing toxic substances that can have an adverse impact on human...Full Text Available

2008-08-01

317

40 CFR 261.2 - Definition of solid waste.  

Science.gov (United States)

...2009-07-01 false Definition of solid waste. 261.2 Section 261.2 Protection...PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) IDENTIFICATION AND LISTING OF HAZARDOUS WASTE General § 261.2 Definition...

2009-07-01

318

Start of the SAPIERR project of regional final storage of radioactive waste in the European Union; Auftakt des SAPIERR-Projekts ueber eine regionale Endlagerung radioaktiver Abfaelle in der Europaeischen Union  

Energy Technology Data Exchange (ETDEWEB)

The first working meeting of the SAPIERR project about regional final storage of radioactive waste in the European Union was held in Piestany, Slovak Republic, on February 19 and 20, 2004. SAPIERR stands for Support Action: Pilot Initiative for European Regional Repositories. This is an independent study supported financially by the European Union within the 6th Research Framework Program. The background to the project is the debate about the feasibility of regional repositories for radioactive waste in the European Union, which has come up again especially with a view to the new accession countries and the draft of a waste management directive within the framework of the Nuclear Package. The results of the SAPIERR Project will be presented in Brussels at a concluding international seminar, most probably in October 2005. The seminar will be open not only to the participating countries but also to other ...

2004-06-01

319

Hanford Waste Management Plan, 1987  

Energy Technology Data Exchange (ETDEWEB)

The purpose of the Hanford Waste Management Plan (HWMP) is to provide an integrated plan for the safe storage, interim management, and disposal of existing waste sites and current and future waste streams at the Hanford Site. The emphasis of this plan is, however, on the disposal of Hanford Site waste. The plans presented in the HWMP are consistent with the preferred alternative which is based on consideration of comments received from the public and agencies on the draft Hanford Defense Waste Environmental Impact Statement (HDW-EIS). Low-level waste was not included in the draft HDW-EIS whereas it is included in this plan. The preferred alternative includes disposal of double-shell tank waste, retrievably stored and newly generated TRU waste, one pre-1970 TRU solid waste site near the Columbia River ...

1987-01-01

320

Ecological utilization of wastes. A manual for optimum waste management concepts. 3. rev. ed. Oekologische Muellverwertung. Handbuch fuer optimale Abfall-Konzepte  

Energy Technology Data Exchange (ETDEWEB)

From out of the numerous technical alternatives the manual develops a waste management concept with emphasis on methods which can be coordinated for maximum ecological use and minimum economic costs. A clear-cut analysis of the present state of waste utilization and waste disposal in the Federal Republic of Germany (chapter 1) is followed by a detailed description of conventional and modern state-of-the-art waste utilization methods based on ecological evaluation criteria (chapter 3). An optimum waste utilization concept for defined quantities of wastes is derived from the ecological and economic comparison of waste utilization techniques given in chapter 3. Chapter 4 points out different variants of waste utilization and waste disposal methods and shows how to determine the optimum variant of the ...

1991-01-01

321

Waste Management Project fiscal year 1998 multi-year work plan, WBS 1.2  

Energy Technology Data Exchange (ETDEWEB)

The Waste Management Project manages and integrates (non-TWRS) waste management activities at the site. Activities include management of Hanford wastes as well as waste transferred to Hanford from other DOE, Department of Defense, or other facilities. This work includes handling, treatment, storage, and disposal of radioactive, nonradioactive, hazardous, and mixed solid and liquid wastes. Major Waste Management Projects are the Solid Waste Project, Liquid Effluents Project, and Analytical Services. Existing facilities (e.g., grout vaults and canyons) shall be evaluated for reuse for these purposes to the maximum extent possible.

1997-09-23

322

Thermal waste disposal and utilization; Waste management in accordance with the German Municipal Waste Disposal Regulations. Abfaelle thermisch entsorgen und verwerten; Die Verwaltungsvorschrift TA Siedlungsabfall praegt gesamte Abfallbehandlung  

Energy Technology Data Exchange (ETDEWEB)

Drastic changes in waste management procedures are expected from the German Municipal Waste Disposal Regulations which became effective on June 1, 1993. Waste disposal will be subject to certain restrictions which, e.g. demand that wastes must be pretreated and inerted before they are stored. These regulations favor thermal waste disposal methods such as the carbonization/combustion method which is planned for a commercial-scale plant in the city of Fuerth. (orig./BBR)

1993-09-01

323

Surface Crystallization and Composition of Spinel and Acmite in High-Level Waste Glass  

Science.gov (United States)

Surface crystallization and surface-to-bulk ratio in high-level waste glasses.

2000-07-10

324

Safe management of wastes from the mining and milling of Uranium and Thorium ores  

CERN Document Server

Safe management of wastes from the mining and milling of Uranium and Thorium ores

1987-01-01

325

Hazardous Waste Management on the Farm  

Science.gov (United States)

Sep 2, 2008 ... Abstract: This tutorial is intended to serve as a guide towards proper hazardous waste management. Knowing the regulations, different ...

326

Control of Effluent Gases from Solid Waste Processing Using Carbon Nanotubes  

Science.gov (United States)

One of the major problems associated with solid waste processing technologies is the release of

2005-01-01

328

State-of-the-art review of computational fluid dynamics modeling for fluid-solids systems  

Energy Technology Data Exchange (ETDEWEB)

As the result of 15 years of research (50 staff years of effort) Argonne National Laboratory (ANL), through its involvement in fluidized-bed combustion, magnetohydrodynamics, and a variety of environmental programs, has produced extensive computational fluid dynamics (CFD) software and models to predict the multiphase hydrodynamic and reactive behavior of fluid-solids motions and interactions in complex fluidized-bed reactors (FBRS) and slurry systems. This has resulted in the FLUFIX, IRF, and SLUFIX computer programs. These programs are based on fluid-solids hydrodynamic models and can predict information important to the designer of atmospheric or pressurized bubbling and circulating FBR, fluid catalytic cracking (FCC) and slurry units to guarantee optimum efficiency with minimum release of pollutants into the environment. This latter issue will become of paramount importance with the enactment of the Clean Air Act ...

1994-05-12

329

Energy Conversion and Storage Program. 1990 annual report  

Energy Technology Data Exchange (ETDEWEB)

The Energy Conversion and Storage Program applies chemistry and materials science principles to solve problems in (1) production of new synthetic fuels, (2) development of high-performance rechargeable batteries and fuel cells, (3) development of advanced thermochemical processes for energy conversion, (4) characterization of complex chemical processes, and (5) application of novel materials for energy conversion and transmission. Projects focus on transport-process principles, chemical kinetics, thermodynamics, separation processes, organic and physical chemistry, novel materials, and advanced methods of analysis. Electrochemistry research aims to develop advanced power systems for electric vehicle and stationary energy storage applications. Topics include identification of new electrochemical couples for advanced rechargeable batteries, improvements in battery and fuel-cell materials, and the establishment of engineering principles applicable to electrochemical ...

1992-03-01

330

Energy Conversion and Storage Program  

Energy Technology Data Exchange (ETDEWEB)

The Energy Conversion and Storage Program applies chemistry and materials science principles to solve problems in (1) production of new synthetic fuels, (2) development of high-performance rechargeable batteries and fuel cells, (3) development of advanced thermochemical processes for energy conversion, (4) characterization of complex chemical processes, and (5) application of novel materials for energy conversion and transmission. Projects focus on transport-process principles, chemical kinetics, thermodynamics, separation processes, organic and physical chemistry, novel materials, and advanced methods of analysis. Electrochemistry research aims to develop advanced power systems for electric vehicle and stationary energy storage applications. Topics include identification of new electrochemical couples for advanced rechargeable batteries, improvements in battery and fuel-cell materials, and the establishment of engineering principles applicable to electrochemical ...

1992-03-01

331

Development in harmony with our environment : final report of the Manitoba Round Table on Environment and the Economy 1988-1997  

Energy Technology Data Exchange (ETDEWEB)

This final report of the Manitoba Round Table on Environment and Economy (MRTEE) chronicles its history, objectives, accomplishments and ongoing challenges from 1988-1997. MRTEE`s mandate was to promote environmentally sustainable economic development in Manitoba through policies and programs that combine environmental concerns with economic decisions. The seven main objectives of the MRTEE were: (1) the implementation of a sustainable development strategy for Manitoba, (2) the design of a communications program on environment-economy integration and an action plan to upgrade environmental education, (3) implementation of market-driven and incentive programs to promote environmental protection by business, agriculture and resource users, (4) implementation of sustainable development within the public sector, (5) encouragement of individual businesses, farms and resource users to adopt codes of environmental practice, (6) ...

1998-12-01

332

Request for interim approval to operate Trench 94 of the 218-E-12B Burial Ground as a chemical waste landfill for disposal of polychlorinated biphenyl waste in submarine reactor compartments. Revision 2.  

Science.gov (United States)

This request is submitted to seek interim approval to operate a Toxic Substances Control Act (TSCA) of 1976 chemical waste landfill for the disposal of polychlorinated biphenyl (PCB) waste. Operation of a chemical waste landfill for disposal of PCB waste ...

1994-01-01

333

Radioactive and mixed waste management plan for the Lawrence Berkeley Laboratory Hazardous Waste Handling Facility  

Energy Technology Data Exchange (ETDEWEB)

This Radioactive and Mixed Waste Management Plan for the Hazardous Waste Handling Facility at Lawrence Berkeley Laboratory is written to meet the requirements for an annual report of radioactive and mixed waste management activities outlined in DOE Order 5820.2A. Radioactive and mixed waste management activities during FY 1994 listed here include principal regulatory and environmental issues and the degree to which planned activities were accomplished.

1995-01-01

334

Composting - environmentally compatible waste disposal - one of the incredients of waste management  

Energy Technology Data Exchange (ETDEWEB)

Considering the fact that more than 40% of all household wastes are organic wastes composting could be an excellent relief and complement to other waste disposal methods (e.g. combustion or direct landfills). Provided the right conditions household wastes could be composted together with sewage sludges and manures. The paper discusses the legal aspects, quantitative evaluations, conveying systems, as well as the compost utilization and marketing aspects valid for the Federal Republic of Germany.

1988-09-20

335

Charging generators for waste management costs  

Energy Technology Data Exchange (ETDEWEB)

Implementation of a plan to charge waste management costs to the facility that generates such waste requires a long-term commitment and consistent administration. The benefit is that generators are provided the incentive to optimize waste management practices if the charges are appropriately applied. This paper summarizes (1) a plan to charge waste generators, (2) the administrative structure of the plan, (3) a comparison between the rate structure and changes in waste disposal operations, and (4) issues that have surfaced as the plan is implemented. 2 refs., 1 fig., 1 tab.

1988-01-01

336

AVLIS production plant waste management plan  

Energy Technology Data Exchange (ETDEWEB)

Following the executive summary, this document contains the following: (1) waste management facilities design objectives; (2) AVLIS production plant wastes; (3) waste management design criteria; (4) waste management plan description; and (5) waste management plan implementation. 17 figures, 18 tables.

1984-11-15

337

Hospital waste management in Lebanon  

International Nuclear Information System (INIS)

Hospital wastes comprises approximately 80% domestic waste components, also known as non-risk waste and 20% hazardous or risk waste. The 20% of the hospital waste stream or the risk waste (also known as infectious, medical, clinical wastes) comprises components which could be potentially contaminated with infections, chemical or radioactive agents. Therefore, it should be handled and disposed of in such a manner as to minimize potential human exposure and cross-contamination. Hospital risk waste and be subdivided into seven general categories as follows: infections, anatomical/pathological, chemical, pharmaceutical, radioactive waste, sharps and pressurised containers. These waste categories are generated by many types of health care establishments, including hospitals, clinics, ...

1999-06-02

338

Waste recycling as evaluated from the viewpoint of energy environment, mainly about plastics; Haikibutsu recycle no energy kankyomen kara no hyoka. Plastic wo chushin to shite  

Energy Technology Data Exchange (ETDEWEB)

Some comments are given on the recycling of waste, mainly plastics, as evaluated from the viewpoint of energy environment. Discussed about the waste in general are the definition and classification, generation and resource recovery rates, current state of recycling, problems about recycling, related legislation, and current conditions overseas. Discussed about the treatment and recycling of plastics waste are the characters and use of plastic product, current state of waste plastics treatment, current state of waste plastics recycling (material recycling, thermal recycling), energy recovery by thermal recycling, quantity recyclable from waste plastics, energy consumption and cost for waste plastics recycling, effect and impact of increase in waste plastics in case material recycling is forwarded, and prospect of ...

1996-05-01

339

Coal Liquefaction Program: Fiscal year 1989, Summary program plan  

Energy Technology Data Exchange (ETDEWEB)

Program plans of the Office of Coal Technology in coal liquefaction are presented. Technology description, status, market applications, program strategy and program management descriptions are included. 2 figs. (CBS)

1989-01-01

340

Waste laws. Waste Classification Ordinance. Residual Material Classification Ordinance. The Waste Technical Code. Ordinance on the Monitoring of Wastes and Residual Material. Ordinance on the Ban on CFCs and Halogenated Hydrocarbons. Packaging Ordinance. Sewage Ordinance. Text edition with index and an introduction by Dr. Clemens Weidemann. As of May 15, 1992. Abfallgesetz. AbfallbestimmungsV. ReststoffbestimmungsV. TA Abfall. Abfall- und ReststoffueberwachungsV. FCKW-Halon-VerbotsV. VerpackungsV. KlaerschlammV. Textausgabe mit Sachverzeichnis und einer Einfuehrung von Rechtsanwalt Dr. Clemens Weidemann. Stand: 15. Mai 1992  

Energy Technology Data Exchange (ETDEWEB)

The turbulent history of legislature concerned with the waste-management industry and the amount of material on this subject as well as the significance of the material in its own right led to the decision to publish all legal regulations on waste in one volume. It includes above all the Waste Law, Regulations on Determination of Waste, Regulations on Determination of Residual Products, Technical Instructions for Waste, Regulations for Monitoring Waste and Residual Products, Regulations on Probition from the Use of Chlorofluorohydrocarbons and Halon, Regulations on Packaging and Regulations on Sewage Sludge. The introduction explains the development and the role of the Waste Law and its applicability, goals and principles: The concept of waste, avoidance of waste, avoidance of ...

1992-01-01

341

Attenuation of heavy metal leaching from hazardous wastes by co-disposal of wastes  

Energy Technology Data Exchange (ETDEWEB)

The potential hazard of landfill wastes was previously evaluated by examining the extraction procedures for individual waste, although various wastes were co-disposed of in actual landfills. This paper investigates the reduction of extraction-procedure toxicity by co-disposing various combinations of two wastes. When two wastes are mixed homogeneously, the extraction of heavy metals from the waste mixture is critically affected by the extract pH. Thus, co-disposal wastes will have a resultant pH between the pH values of its constituent. The lower the resultant pH, the lower the concentrations of heavy metals in the extract. When these wastes are extracted sequentially, the latter extracted waste has a stronger influence on the final concentration of heavy metals in the extract. Small-scale lysimeter ...

1996-12-31

342

Survey reveals Europe's refinery-waste disposal methods, amounts, and costs  

Energy Technology Data Exchange (ETDEWEB)

Results of a survey conducted by Concawe on 75 oil refineries in Europe show that the total quantity of waste requiring disposal in 1986 was 0.5 million metric tons. This quantity of waste is but 0.13% of the total refinery throughput of 387 million metric tons during 1986. The survey revealed a wide range of disposal costs, depending on the particular properties of the waste and local conditions. A summary of total waste generation and how the waste is disposed of is shown. Details on the types of waste disposed, the disposal methods used, and the costs of disposal are detailed in this excerpt from the Concawe survey.

1989-08-28

343

ICDF Complex Operations Waste Management Plan  

Science.gov (United States)

This Waste Management Plan functions as a management and planning tool for managing waste streams generated as a result of operations at the Idaho CERCLA Disposal Facility (ICDF) Complex. The waste management activities described in this plan support the selected remedy presented in the Waste Area Group 3, Operable Unit 3-13 Final Record of Decision for the operation of the Idaho CERCLA Disposal Facility Complex. This plan identifies the types of waste that are anticipated during operations at the Idaho CERCLA Disposal Facility Complex. In addition, this plan presents management strategies and disposition for these anticipated waste streams.

2006-12-01

344

Transuranium-element-contaminated soil cleanup  

International Nuclear Information System (INIS)

Johnston Atoll (JA) is a small (270-ha), but strategic, US possession in the Pacific Ocean, which was previously used in nuclear weapons testing. Nuclear devices were launched by missile for detonations at very high altitudes. In 1962, one missile failed on the launch pad and two failed overhead. The devices were destructed without nuclear yield, but transuranium (TRU) elements were dispersed. Cleanup was swift and incomplete. A 2-ha area was placed under radiological controls and restricted from use due to residual contamination. Planning was begun in 1983 for a total JA cleanup to provide additional (unrestricted) land to meet future requirements. A TRUe soil cleanup is programmed to begin at JA in 1988 utilizing a full-scale mining plant. The plant should be able to process all contaminated soil by 1992 and produce less than #approx# 2000 m"3 of concentrated waste. This cleanup will increase the amount of land available for unrestricted use ...

1987-06-07

345

The fate of trace elements at coal-fired power plants  

International Nuclear Information System (INIS)

Within the framework of a Dutch research program on the environmental effects of coal combustion 15 measuring campaigns were carried out in the eighties. All the relevant ingoing and outgoing flows of electric power plants were sampled and the heavy metals composition was determined. An overview is given of these fifteen measuring campaigns. It is concluded that between 99.7% and 99.9% of the fly ash can be separated by electrofilters. The removal of solid elements is higher than 99%, except for those elements, which are enriched in the fly ash, f.e. Cd and Se (>90% removal is possible). Additional separation of the emissions of fly ash and elements in the fly ash takes place in a flue gas desulfurization (FGD) installation. Some elements are emitted as gaseous wastes. After the electrofilter Cl, F and I can be found for almost 100%, Br and Hg for 50% on average, and only small amounts of As and Se in the gaseous phase. In a wet FGD unit ...

346

RCRA Facilities Assessment (RFA)---Oak Ridge National Laboratory  

Energy Technology Data Exchange (ETDEWEB)

US Department of Energy (DOE) facilities are required to be in full compliance with all federal and state regulations. In response to this requirement, the Oak Ridge National Laboratory (ORNL) has established a Remedial Action Program (RAP) to provide comprehensive management of areas where past and current research, development, and waste management activities have resulted in residual contamination of facilities or the environment. This report presents the RCRA Facility Assessment (RFA) required to meet the requirements of RCRA Section 3004(u). Included in the RFA are (1) a listing of all sites identified at ORNL that could be considered sources of releases or potential releases; (2) background information on each of these sites, including location, type, size, period of operation, current operational status, and information on observed or potential releases (as required in Section II.A.1 of the RCRA permit); (3) analytical results obtained ...

1987-03-01

347

Observational approach implementation guidance: Year-end report  

Energy Technology Data Exchange (ETDEWEB)

It is generally recognized that the Remedial Investigation/Feasibility Study (RI/FS) process can be time-consuming and costly. To expedite the process, the Environmental Protection Agency, through the National Contingency Plan and Office of Solid Waste and Emergency Response (OSWER) Directives, has promoted streamlining'' the RI/FS. The concept of streamlining is directly applicable to Resource Conservation and Recovery Act (RCRA) Remedial Facility Investigation/Corrective Measure Study (RFI/CMS) as well. The US Department of Energy's (DOE's) environmental restoration process promises to be lengthy and expensive: therefore, the Office of Environmental Restoration (EM-40) believes that it is to incorporate streamlining into RI/FS and RFI/CMS efforts across the DOE complex. The Office of Program Support (EM-43) has asked Pacific Northwest Laboratory (PNL) to provide presentations and workshops on streamlining ...

1992-06-01

348

Dynamics of the changing utility world  

Energy Technology Data Exchange (ETDEWEB)

There are many factors contributing to the changes taking place within the electric utility industry. The environmental pressures on the industry are substantial and include the global warming issue, hazardous and nuclear waste challenges, air toxicities, and the electromagnetic field controversy. An issue of special concern is deregulation of the industry, which brought with it retail wheeling, wholesale wheeling, transmission access, and market-based pricing, all of which have greatly shaken the industry. The changes are expected to happen quickly. This is quite different from the 31 years it took to deregulate the telecommunications industry, the 15 to 20 years for railroads, the 9 years for the natural gas industry, and the 2 years for the airline industry. Historically there has been a general willingness among the utilites to share information through collaborative research. Research and development is viewed as a cost and not an investment in the electric ...

1996-01-01

349

Development of radioisotope tracer technology  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to develop the radioisotope tracer technology, which can be used in solving industrial and environmental problems and to build a strong tracer group to support the local industries. In relation to the tracer technology in 1999, experiments to estimate the efficiencies of a sludge digester of a waste water treatment plant and a submerged biological reactor of a dye industry were conducted. As a result, the tracer technology for optimization of facilities related to wastewater treatment has been developed and is believed to contribute to improve their operation efficiency. The quantification of the experimental result was attempted to improve the confidence of tracer technology by ECRIN program which basically uses the MCNP simulation principle. Using thin layer activation technique, wear of tappet shim was estimated. Thin layer surface of a tappet shim was irradiated by proton beam and the correlation between the ...

2000-04-01

350

Development of a generic analysis code of dynamic compartment model for evaluation of doses in terrestrial biosphere  

International Nuclear Information System (INIS)

The release rate of a nuclide from a reactor or a radioactive waste disposal plant at the accident is not steady, but varies with time. The various parameters of a nuclide migration into environment vary also day after day, or with the seasons. In such cases, dynamic behavior of the nuclide in the environment must be taken into consideration. It is difficult for a mathematical model to involve all of mechanisms for the nuclide migration. The environment for evaluation of doses are usually divided into some of compartments in which a nuclide concentration is uniform. Time variations of the nuclide concentration in the compartment are described in simultaneous differential equations. The nuclide concentration can be solved as a time function, and the radiation doses, therefore, can be estimated as a time function. Generic analysis code for dynamic compartment model (GACOM) is developed for the nuclide migration and the evaluation of doses in terrestrial biosphere. ...

1999-02-01

351

Combined cycle power plant with integrated low temperature heat (LOTHECO)  

International Nuclear Information System (INIS)

The major driver to enhance the efficiency of the simple gas turbine cycle has been the increase in process conditions through advancements in materials and cooling methods. Thermodynamic cycle developments or cycle integration are among the possible ways to further enhance performance. The current paper presents the possibilities and advantages from the LOTHECO natural gas-fired combined cycle concept. In the LOTHECO cycle, low-temperature waste heat or solar heat is used for the evaporation of injected water droplets in the compressed air entering the gas turbine's combustion chamber. Following a description of this innovative cycle, its advantages are demonstrated by comparison between different gas turbine power generation systems for small and large-scale applications, including thermodynamic and economic analysis. A commercial gas turbine (ALSTOM GT10C) has been selected and computed with the heat mass balance program ENBIPRO. The results ...

2004-08-01

352

Characterization of spent fuel approved testing material: ATM-106  

Energy Technology Data Exchange (ETDEWEB)

The characterization data obtained to date are described for Approved Testing Material (ATM)-106 spent fuel from Assembly BT03 of pressurized-water reactor Calvert Cliffs No. 1. This report is one in a series being prepared by the Materials Characterization Center at Pacific Northwest Laboratory on spent fuel ATMs. The ATMs are receiving extensive examinations to provide a source of well- characterized spent fuel for testing in the US Department of Energy Office of Civilian Radioactive Waste Management (OCWRM) program. ATM-106 consists of 20 full-length irradiated fuel rods with rod-average burnups of about 3700 GJ/kgM (43 MWd/kgM) and expected fission gas release of /approximately/10%. Characterization data include (1) as-fabricated fuel design, irradiation history, and subsequent storage and handling; (2) isotopic gamma scans; (3) fission gas analyses; (4) ceramography of the fuel and metallography of the cladding; (5) calculated nuclide ...

1988-10-01

353

Characterization of spent fuel approved testing material: ATM-103  

Energy Technology Data Exchange (ETDEWEB)

The characterization data obtained to date are described for Approved Testing Material (ATM)-103, which is spent fuel from Assembly D101 of pressurized-water reactor Calvert Cliffs, No. 1. This report is one in a series being written by the Materials Characterization Center (MCC) at Pacific Northwest Laboratory (PNL) on spent fuel ATMs. The ATMs are receiving extensive examinations to provide a source of well-characterized spent fuel for testing in the US nuclear waste repository program. ATM-103 consists of 176 full-length irradiated fuel rods with rod-average burnups of about 2600 GJ/kgM (30 MWd/kgM) and less than 1% fission gas release. Characterization data include 1) as-fabricated fuel design, irradiation history, and subsequent storage and handling; 2) isotopic gamma scans; 3) fission gas analyses; 4) ceramography of the fuel and metallography of the cladding; 5) special fuels studies involving analytical transmission electron microscopy ...

1988-04-01

354

Characterization of spent fuel approved testing material--ATM-104  

Energy Technology Data Exchange (ETDEWEB)

The characterization data obtained to date are described for Approved Testing Material 104 (ATM-104), which is spent fuel from Assembly DO47 of the Calvert Cliffs Nuclear Power Plant (Unit 1), a pressurized-water reactor. This report is one in a series being prepared by the Materials Characterization Center at Pacific Northwest Laboratory (PNL) on spent fuel ATMs. The ATMs are receiving extensive examinations to provide a source of well-characterized spent fuel for testing in the US Department of Energy Office of Civilian Radioactive Waste Management (OCRWM) Program. ATM-104 consists of 128 full-length irradiated fuel rods with rod-average burnups of about 42 MWd/kgM and expected fission gas release of about 1%. A variety of analyses were performed to investigate cladding characteristics, radionuclide inventory, and redistribution of fission products. Characterization data include (1) fabricated fuel design, irradiation history, and subsequent ...

1991-12-01

355

Characterization of spent fuel approved testing material---ATM-105  

Energy Technology Data Exchange (ETDEWEB)

The characterization data obtained to data are described for Approved Testing Material 105 (ATM-105), which is spent fuel from Bundles CZ346 and CZ348 of the Cooper Nuclear Power Plant, a boiling-water reactor. This report is one in a series being prepared by the Materials Characterization Center at Pacific Northwest Laboratory (PNL) on spent fuel ATMs. The ATMs are receiving extensive examinations to provide a source of well-characterized spent fuel for testing in the US Department of Energy Office of Civilian Radioactive Waste Management (OCRWM) Program. ATM-105 consists of 88 full-length irradiated fuel rods with rod-average burnups of about 2400 GJ/kgM (28 MWd/kgM) and expected fission gas release of about 1%. Characterization data include (1) descriptions of as-fabricated fuel design, irradiation history, and subsequent storage and handling; (2) isotopic gamma scans; (3) fission gas analyses; (4) ceramography of the fuel and metallography ...

1991-12-01

356

Area G perimeter surface-soil and single-stage water sampling: Environmental surveillance for fiscal year 94, Group ESH-19. Progress report  

Energy Technology Data Exchange (ETDEWEB)

ESH-19 personnel collected soil and single-stage water samples around the perimeter of Area G at Los Alamos National Laboratory during FY94 to characterize possible contaminant movement out of Area G through surface-water and sediment runoff. These samples were analyzed for tritium, total uranium, isotopic plutonium, americium-241, and cesium-137. Ten metals were also analyzed on selected soils using analytical laboratory techniques. All radiochemical data are compared with analogous samples collected during FY 93 and reported in LA-12986. Baseline concentrations for future disposal operations were established for metals and radionuclides by a sampling program in the proposed Area G Expansion Area. Considering the amount of radioactive waste that has been disposed at Area G, there is evidence of only low concentrations of radionuclides on perimeter surface soils. Consequently, little radioactivity is leaving the confines of Area G via the ...

1996-08-01

357

Ameliorating effects of industrial sugar residue on the Jales gold mine spoil (NE Portugal) using Holcus lanatus and Phaseolus vulgaris as indicators  

Energy Technology Data Exchange (ETDEWEB)

A residue of the sugar industry can be used in revegetation programs on metal contaminated sites. - Phytostabilisation of bare heavily contaminated substrate, such as abandoned mine sites, is considered a very appropriate technology in order to diminish erosion and dispersion of contaminants into the surroundings. In this short-term pot study, application of industrial sugar residue (ISR), a waste product of the sugar industry, proved to ameliorate spoils conditions for plant performance by elevating pH and immobilising several metals. Although arsenate concentrations were positively correlated to spoil pH and spoil treatment with ISR mobilised As, growth of both Phaseolus vulgaris and Holcus lanatus improved significantly after applications of 3.75 g ISR kg{sup -1} dry spoil. Nutrient uptake from the substrate, with the exception of potassium, was elevated by ISR. As a remediation technique ISR application could be effective although in ...

2003-09-01

358

Streams of solid municipal wastes. Evaluation of data on the basis of waste follow-up system; Kiinteaen yhdyskuntajaetteen virrat: aineistotarkastelua jaetealan seurantajaerjestelmaen avulla  

Energy Technology Data Exchange (ETDEWEB)

The follow-up system for wastes (JAeSTI), developed at the end of the 1990s, forms a basis for today's followup activities in Finland. JAeSTI relies on an environmental protection database, the compliance monitoring system VAHTI operated by the environmental authorities. Waste followup and waste statistics depend very much on the annual waste quantities recorded in the VAHTI system. In the KYJ-project the coverage and reliability of the data in the VAHTI system was evaluated as for the streams of solid municipal waste. The project also included the compiling of national statistics on municipal waste for the year 2000. The project used other information sources, too, such as statistics compiled when the National Waste Plan and regional waste plans were revised in 2002. In addition, the extent and quantity of ...

2004-07-01

359

Utilizing the right mix of environmental cleanup technologies  

International Nuclear Information System (INIS)

The Savannah River Site (SRS) is a 310-square-mile United States Department of Energy nuclear facility located along the Savannah River near Aiken, South Carolina. During operations, which started in 1951, hazardous substances (chemicals and radionuclides) were released to the environment. The releases occurred as a result of inadvertent spills and waste disposal in unlined pits and basins which was common practice before environmental regulations existed. The hazardous substances have migrated to the vadose zone and groundwater in many areas of the SRS, resulting in 515 waste units that are required by environmental regulations, to undergo characterization and, if needed, remediation. In the initial years of the SRS environmental cleanup program (early 1990's), the focus was to use common technologies (such as pump and treat, air stripping, excavation and removal) that actively and tangibly removed contamination. Exclusive ...

2007-09-02

360

Subseabed disposal: systematic application of the site qualification plan  

Energy Technology Data Exchange (ETDEWEB)

Two criteria, geologic stability and barrier effectiveness, form the basis of the Subseabed Disposal Program's site qualification plan to evaluate the ocean basins and identify those regions having characteristics most favorable for containment of radioactive waste. Stability criteria are used to define those regions least likely to be disturbed by tectonic forces or oceanographic changes during the lifetime of a waste repository. Barrier criteria define those lithologies most likely to form an effective barrier to the release of radionuclides. Two north Pacific regions and three north Atlantic regions (PAC I and II and ATL I, II, and III, respectively) have thus far been selected for further investigation based on the site qualification plan. The PAC I region, centered on the Shatsky Rise in the northwest Pacific, has been subdivided into areas and locations on the basis of an exhaustive review of data available ...

1982-01-01

361

Responses to comments on the remedial investigation/feasibility study-environmental impact statement for remedial action at the Chemical Plant area of the Weldon Spring site (November 1992)  

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy (DOE) is responsible for cleanup activities at the Weldon Spring site in St. Charles County, Missouri. The site consists of a chemical plant area and a noncontiguous limestone quarry; both areas are radioactively and chemically contaminated as a result of past processing and disposal activities. Explosives were produced by the US Army at the chemical plant in the 1940s, and uranium and thorium materials were processed by DOE`s predecessor agency in the 1950s and 1960s. During that time, various wastes were disposed of at both areas of the site. The DOE is conducting cleanup activities at the site under its Environmental Restoration and Waste Management Program. The integrated remedial investigation/feasibility study-environmental impact statement (RI/FS-EIS) documents for the chemical plant area were issued to the public in November 1992 as the draft RI/FS-EIS. (The CERCLA RI/FS is considered ...

1993-06-01

362

Pre-operational monitoring plan for LIL waste disposal at Saligny  

International Nuclear Information System (INIS)

Developed under the PN II Project 71-009 - MONA, the pre-operational monitoring program of the LIL waste disposal site presented in this paper covers the main elements requested for a continuous improvement of site characterization and safety assessment, as well as for the set up of the baseline data requested for the future operational and post-operational monitoring and surveillance. These elements are: vadose and saturated zones hydrogeology, surface erosion, meteorology and radionuclides content in waters, soil and biota. Pairs of TDR (Time Domain Reflectometry) and pressure sensors, coupled with a meteorological station have been installed on site for the continuously measurement of the water content and matric potential changes due to the climate variations. The data will be used to follow the water balance, the pores water velocity and to calculate the infiltration rate. A new set of erosion rates experimentally determined by Pinhole ...

2009-10-12

363

Disposal of old heads for Daya Bay NPP  

International Nuclear Information System (INIS)

The paper introduces the disposal procedures of the old reactor pressure vessel head. Reactor pressure vessel (RPV) heads were replaced successfully in Daya Bay Nuclear Power Plant. The on-site treatment and disposal of replaced heads was thereafter implemented. This is the first time in China for large size radioactive article disposal. To guarantee the safety of old head treatment, issues of radiation protection have to be taken into account. Dose rate distribution of the old head surface and radioactivity were initially calculated according to the operation history and the neutron flux rate of the reactor. Shielding calculation and package design was thereafter worked out based on the data obtained from the old head, e.g. neutron flux, sorts of nuclides, radioactivity and dose rates. Shielding package was afterwards manufactured in special factories and transported to Daya Bay NPP site by truck and ship. The shielding package was designed relatively simple, practicable and comply ...

364

The Waste of the World  

Environmental Research Database

ObjectivesThis programme aims; To rethink how waste is thought about in social science; To provide a global analysis of waste; To examine how rethinking waste impinges on core social science concerns, notably: economies, researching globalisation, hazards and risk, and materiality. Social science understandings of waste position waste as the end-point of production and consumption, and see waste as a question of disposal.DescriptionThe Waste of the World is a five year research programme funded under ESRC's Large Grant Scheme. It brings together researchers in geography, anthropology and materials science from the University of Sheffield, Durham University, University College London and Goldsmiths College London, and connects the UK with South Asia (particularly India and Bangladesh), as well as the US, Europe and Kazakhstan. The ...

2011-01-30

365

Operable Unit 3-13, Group 3, Other Surface Soils Remediation Sets 4-6 (Phase II) Waste Management Plan  

Energy Technology Data Exchange (ETDEWEB)

This Waste Management Plan describes waste management and waste minimization activities for Group 3, Other Surface Soils Remediation Sets 4-6 (Phase II) at the Idaho Nuclear Technology and Engineering Center located within the Idaho National Laboratory. The waste management activities described in this plan support the selected response action presented in the Final Record of Decision for Idaho Nuclear Technology and Engineering Center, Operable Unit 3-13. This plan identifies the waste streams that will be generated during implementation of the remedial action and presents plans for waste minimization, waste management strategies, and waste disposition.

2006-07-01

366

Treatment of radioactive metallic waste by the electro-slag melting method  

Energy Technology Data Exchange (ETDEWEB)

The applicability of the electro-slag melting method for treating plutonium contaminated metallic waste was studied. A 100kg test furnace was built and simulated metallic waste was melted and solidified in this furnace. Waste volume was reduced to 1/25 with a decontamination factor of 25 and the slag and the copper mold are repeatedly usable. The process is expected to be employed in the project of PWTF (Plutonium contaminated Waste Treatment Facilities).

1983-01-01

367

Request for interim approval to operate 218-E-12B Trench 94 as a chemical waste landfill for disposal of polychlorinated biphenyl wastes in submarine reactor compartments.  

Science.gov (United States)

This request is submitted to seek interim approval to operate a chemical waste landfill for the disposal of polychlorinated biphenyl (PCB) wastes. This request covers only the disposal of small quantities of solid PCB wastes contained in decommissioned su...

1990-01-01

368

Projected radionuclide inventories of DWPF glass from current waste at time of production  

Energy Technology Data Exchange (ETDEWEB)

The Waste Acceptance Preliminary Specifications (WAPS) require that the DWPF estimate the inventory of long-lived radionuclides present in the waste glass, and report the values in the Waste Form Qualification Report. In this report, conservative (biased high) estimates of the radionuclide inventory of glass produced from waste currently in the Tank Farm are provided. In most cases, these calculated values compare favorably with actual data. In those cases where the agreement is not good, the values reported here are conservative.

1993-02-04

369

Industrial waste and pollution in Mongolia  

Energy Technology Data Exchange (ETDEWEB)

This paper very briefly outlines hazardous waste management issues, including regulations, in Mongolia. Air, water, and soil pollutants are identified and placed in context with climatic, social, and economic circumstances. The primary need identified is technology for the collection and disposal of solid wastes. Municipal waste problems include rapid urbanization and lack of sanitary landfills. Industrial wastes of concern are identified from the mining and leather industries. 4 refs., 2 tabs.

1996-12-31

370

Finally authorized supplementary report to the review on waste disposal in the Copenhagen area 1988. [Denmark]. Endelig godkendt bilagsrapport til affaldsredegoerelse for hovedstadsregionen 1988; Bilagsrapport nr. 1  

Energy Technology Data Exchange (ETDEWEB)

A supplementary report to the plan for waste disposal in the Copenhagen area, Denmark. It presents a mapping of wastes and waste flow in invidual areas, a description of recycling methods and waste collection systems. In addition legislative demands and potentials are dealth with. (CLS).

1988-07-01

371

WINPEPI updated: computer programs for epidemiologists, and their teaching potential  

UK PubMed Central (United Kingdom)

BackgroundThe WINPEPI computer programs for epidemiologists are designed for use in practice and research in the health field and as learning or teaching aids. The programs are free,...Full Text Available

372

The DARPA High-Performance Polymer Program. Volume 1. ...  

Science.gov (United States)

... IDA DOCUMENT D- 1174 THE DARPA HIGH-PERFORMANCE POLYMER PROGRAM ... The DARPA High-Performance Polymer Program, Volume I: ...

1992-09-01

373

Interactive computer programs in sequence data analysis.  

UK PubMed Central (United Kingdom)

We present interactive computer programs for the analysis of nucleic acid sequences. In order to handle these programs, minimum computer experience is sufficient. The nucleotide sequence of the human...Full Text Available

1982-01-11

374

Instructional Materials Development Program  

Science.gov (United States)

... Materials Development Program TECHNOLOGY EDUCATION INSTRUCTIONAL MATERIALS Elementary - High School ... of technology education materials through its Instructional Materials Development (IMD) program. The ...

375

Industrial Technologies Program: Chemicals  

Science.gov (United States)

Efficiency and Renewable Energy EERE Home | Programs & Offices | Consumer Information Chemicals Search Search Help Chemicals EERE » Industrial Technologies Program » Chemicals...

2011-10-01

376

Valuing future citizens' values regarding risk  

Energy Technology Data Exchange (ETDEWEB)

Valuing present citizen's values regarding the risks they face is an important aspect of risk assessment and risk acceptability. Conferences like VALDOR are held for this reason. Governments like Sweden have national referendums on various risk-prone enterprises. The results of these referendums can determine the future of these programs. In the United States, when guidelines are set for determining acceptable levels of risk, the relevant federal agencies are often required to provide a comment period regarding proposed guidelines in order to ascertain the judgments, including the weights place on certain values, of individual members of society as well as stakeholder groups. After the comment period ends, the agency decides on the acceptable level of risk, taking into account the comments from present citizens. Do we also have a duty to value the not-yet-existing values of future citizens, especially if the risks created by the activities of present ...

2006-09-15

377

The Center for Environmental Technology Innovative Technology Screening Process  

Energy Technology Data Exchange (ETDEWEB)

The Center for Environmental Technology`s (CET) mission is to provide a fully integrated system for accelerated evaluation, development, commercialization, and public acceptance of creative environmental solutions which match the foremost demands in today`s environmentally sensitive world. In short, CET will create a means to provide quick, effective solutions for environmental needs. To meet this mission objective, CET has created a unique and innovative approach to eliminating the usual barriers in developing and testing environmental technologies. The approach paves the way for these emerging, cutting-edge technologies by coordinating environmental restoration and waste management activities of industry, universities, and the government to: efficiently and effectively transfer technology to these users, provide market-driven, cost-effective technology programs to the public and DOE, and aid in developing innovative ideas by initiating ...

1995-02-01

378

Planning and management of change  

Energy Technology Data Exchange (ETDEWEB)

The 1990s promise to be a decade of change. In business, the focus will be on restructuring for purposes of improved productivity and efficiency. The Department of Energy (DOE) has recognized that change is on the horizon. The Yucca Mountain Project, carried out under the Office of Civilian Radioactive Waste Management (OCRWM) within the DOE is under new leadership. This new leadership is restructuring its operations to provide better focus, greater efficiency, meaningful products demonstrating progress and a more open operational environment. Criticisms of past operations have been reviewed and evaluated such that the new management organization derives benefit from the past. In recognition that management concerns may be manifested in other areas, Yucca Mountain Project management believes that reorganization is necessary to maximize efficiency. In designing the new organization, a high priority has been placed upon making changes which enable the federal ...

1994-12-31

379

Open test assembly (OTA) shear demonstration testing work/test plan  

Energy Technology Data Exchange (ETDEWEB)

This document describes the development testing phase associated with the OTA Shear activity and defines the controls to be in place throughout the testing. The purpose of the OTA Shear Program was to provide equipment that is needed for the processing of 40 foot long, sodium wetted, irradiated core components previously used in the FFTF reactor to monitor fuel and materials tests. There are currently 15 of these OTA test stalks located in the Test Assembly Conditioning Station (TACS) inerted vault. These need to be dispositioned for a shutdown mission to eliminate this highly activated, high dose inventory prior to turnover to the ERC since they must be handled by remote operations. These would also need to be dispositioned for a restart mission to free up the vault they currently reside in. The waste handling and cleaning equipment in the J33M Cell was designed and built for the handling of reactor components up to the standard 12 foot ...

1998-07-16

380

Full L.A. treatment  

Energy Technology Data Exchange (ETDEWEB)

The high-purity-oxygen activated sludge process will be used to expand secondary treatment capacity and improve water quality in Santa Monica Bay. The facility is operated by the city of Los Angeles Department of Public Works` Bureau of Sanitation. The overall Hyperion Full Secondary Project is 30% complete, including a new headworks, a new primary clarifier battery, an electrical switch yard, and additional support facilities. The upgrading of secondary facilities is 50% complete, and construction of the digester facilities, the waste-activated sludge thickening facility, and the second phase of the three-phase modification to existing primary clarifier batteries has just begun. The expansion program will provide a maximum monthly design capacity of 19,723 L/s(450 mgd). Hyperion`s expansion program uses industrial treatment techniques rarely attempted in a municipal facility, particularly on such a large scale, including: ...

1993-09-01

381

Waste Generation and Pollution Prevention Progress Fact Sheet: Oak Ridge National Laboratory  

Energy Technology Data Exchange (ETDEWEB)

This 2-page fact sheet gives statistics on routine waste generation and projected reduction by waste type, and 1994 pollution prevention and recycling accomplishments at ORNL.

1996-09-01

382

Regional assessment of nonforestry related biomass resources: South Carolina  

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing in a county by county manner the agricultural crop, agricultural wastes, municipal wastes, and industrial wastes of South Carolina that are potential biomass energy sources.

1988-11-01

383

Regional assessment of nonforestry related biomass resources: North Carolina  

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing in a county by county manner the agricultural crop, agricultural wastes, municipal wastes and industrial wastes of North Carolina that are potential biomass energy sources.

1988-11-01

384

Probabilities of a catastrophic waste hoist accident at the Waste Isolation Pilot Plant  

Energy Technology Data Exchange (ETDEWEB)

This report shows the probability of a catastrophic accident involving the WIPP waste hoist system. Calculations and mitigation to reduce the probability of an accident and to minimize the impact of such an accident should be included. 10 refs., 8 figs., 4 tabs.

1990-01-01

385

Oak Ridge National Laboratory Technology Logic Diagram. Volume 2, Technology Logic Diagram: Part C, Waste Management  

Energy Technology Data Exchange (ETDEWEB)

This report documents site remediation at ORNL, including ORNL site characterization technologies, waste management and robotics and automation of the laboratory for waste processing and analysis.

1993-09-01

386

Integrated Models for Solid Waste Management in Tourism Regions: Langkawi Island, Malaysia  

Science.gov (United States)

The population growth, changing consumption patterns, and rapid urbanization contribute significantly to the growing volumes of solid waste that are generated in urban settings. As the rate of urbanization increases, demand on the services of solid waste management increases. The rapid urban growth in Langkawi Island, Malaysia, combined with the increasing rates of solid waste production has provided evidence that the traditional solid waste management practices, particularly the methods of waste collection and disposal, are inefficient and quite nonsustainable. Accordingly, municipal managers and planners in Langkawi ...

2011-09-04

387

Fusion Reactor Radioactive Waste Management.  

Science.gov (United States)

Quantities and compositions of non-tritium radioactive waste are estimated for some current conceptual fusion reactor designs, and disposal of large amounts of radioactive waste appears necessary. Although the initial radioactivity of fusion reactor and f...

1976-01-01

388

Department of Energy low-level waste management strategy  

Energy Technology Data Exchange (ETDEWEB)

The DOE strategy recognizes that public perception of low-level waste management practices is not positive. Actions are included that are aimed at opening the system to the public. A better informed public will be able to better assess the performance of the low-level waste management system.

1980-01-01

389

Cumulative releases of radionuclides from uncontained waste packages  

Energy Technology Data Exchange (ETDEWEB)

This report describes mathematical predictions for the migration of radionuclides from an emplaced radioactive waste container. The model assumes a spherical-equivalent waste solid surrounded by backfill but neglects the effect of decay heat. 7 refs., 2 tabs. (TEM)

1986-07-01

390

Conditioning of plastic wastes for thermal utilization; Aufbereitung von Kunststoffabfaellen zur thermischen Verwertung  

Energy Technology Data Exchange (ETDEWEB)

This article describes the processes for the treatment of plastic waste: sampling, sorting, comminution. The requirements for the different processes for waste treatment (as recycling, utilization as raw material, energy recovery, combustion) are listed. (SR)

1996-12-31

391

Waste management considerations for fusion power reactors  

International Nuclear Information System (INIS)

To estimate the waste management needs of a fusion power reactor, a scheme for handling radioactive waste from a fusion plant has been devised. The handling scheme proceeds with radioactive waste, primarily from blanket replacement, being stored on-site; waste in cooled and shielded casks is then isolated off-site; finally, the materials are recycled. Using activities and component lifetimes supplied by designers, several conceptual fusion power reactors have been analyzed and their waste streams compared to fission reactors with regard to total activity, specific activity, and lifetimes of activity.

392

Waste management considerations for fusion power reactors  

Science.gov (United States)

To estimate the waste management needs of a fusion power reactor, a scheme for handling radioactive waste from a fusion plant has been devised. The handling scheme proceeds with radioactive waste, primarily from blanket replacement, being stored on-site; waste in cooled and shielded casks is then isolated off-site; finally, the materials are recycled. Using activities and component lifetimes supplied by designers, several conceptual fusion power reactors have been analyzed and their waste streams compared to fission reactors with regard to total activity, specific activity, and lifetimes of activity.

1978-02-01

393

Solidification of problem wastes: Annual progress report, October 1985-September 1986  

Energy Technology Data Exchange (ETDEWEB)

This report describes initial work on the development of solidification systems for sodium nitrate waste and compacted waste. Sodium nitrate waste has been solidified in three types of materials: polyethylene, polyester-styrene (PES), and latex cement. Evaluations of the properties of the waste form, such as the ANS 16.1 leaching test, water immersion test and compressive strength measurements were performed on the waste forms containing various amounts of sodium nitrate. 9 refs., 9 figs., 7 tabs.

1987-02-01

394

Present State of Radioactive Waste Management and Treatment Technology at the Research Centre Seibersdorf  

International Nuclear Information System (INIS)

Since 1976 the Austrian Research Centre Seibersdorf has the task to collect, treat and store radioactive waste (Radwaste) arising in Austria. Within the Department of Waste Management a variety of appropriate treatment systems are installed. For storing unconditioned and conditioned waste proper storage-halls are available. The collection of Radwaste is carried out using 100 l drums, for the conditioned waste the 200 l drum concept is used. The interim storage of conditioned waste is done at Seibersdorf until a final repository is built. The present plan foresees one to be in operation at the year 2012. (author).

1996-10-07

395

Hazardous waste operational plan for site 300  

Energy Technology Data Exchange (ETDEWEB)

This plan outlines the procedures and operations used at LLNL's Site 300 for the management of the hazardous waste generated. This waste consists primarily of depleted uranium (a by-product of U-235 enrichment), beryllium, small quantities of analytical chemicals, industrial type waste such as solvents, cleaning acids, photographic chemicals, etc., and explosives. This plan details the operations generating this waste, the proper handling of this material and the procedures used to treat or dispose of the hazardous waste. A considerable amount of information found in this plan was extracted from the Site 300 Safety and Operational Manual written by Site 300 Facility personnel and the Hazards Control Department.

1982-02-12

396

Hazardous waste and environmental trade: China`s issues  

Energy Technology Data Exchange (ETDEWEB)

By presenting some case studies, this paper analyzes China`s situation with regard to hazardous waste: its environmental trade, treatment, and management. The paper describes China`s experiences with the environmental trade of hazardous waste in both the internal and international market. Regulations for managing the import of waste are discussed, as are China`s major approaches to the trading of hazardous waste both at home and overseas. The major reasons for setting up the Asian-Pacific Regional Training Center for Technology Transfer and Environmental Sound Management of Wastes in China and the activities involved in this effort are also described. 1 tab.

1996-12-31

397

Development of the alcohol waste processing equipment  

International Nuclear Information System (INIS)

In the experimental fast Reactor JOYO, gripper of Fuel Handling Machine and Ex-Vessel Transfer Machine that the sodium adhered is being washed with alcohol. This radioactive alcohol waste that was used to the washing is stored to the tank. If it is able to separate the alcohol and sodium in the alcohol waste it becomes possible to dispose of the alcohol waste. Japan Nuclear Institute and Fuji Electric Systems CO., LTD. Developed the device that adds carbonic acid gas to the alcohol waste and cause the sodium in the alcohol waste separated as carbonate and remove this carbonate by using the thin film evaporator. (author)

2004-11-01

398

Interpretation of data obtained from non-destructive and destructive post-test analyses of an intact-core column of culebra dolomite  

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy (DOE) has been developing a nuclear waste disposal facility, the Waste Isolation Pilot Plant (WIPP), located approximately 42 km east of Carlsbad, New Mexico. The WIPP is designed to demonstrate the safe disposal of transuranic wastes produced by the defense nuclear-weapons program. Pefiormance assessment analyses (U.S. DOE, 1996) indicate that human intrusion by inadvertent and intermittent drilling for resources provide the only credible mechanisms for significant releases of radionuclides horn the disposal system. These releases may occur by five mechanisms: (1) cuttings, (2) cavings, (3) spallings, (4) direct brine releases, and (5) long- term brine releases. The first four mechanisms could result in immediate release of contaminant to the accessible environment. For the last mechanisq migration pathways through the permeable layers of rock above the Salado are ...

1998-09-01

399

SUCCESSES AND EMERGING ISSUES IN SIMULATING THE MIXING BEHAVIOR OF LIQUID-PARTICLE NUCLEAR WASTE SLURRIES AT THE SAVANNAH RIVER SITE - 211B  

Energy Technology Data Exchange (ETDEWEB)

Aqueous radioactive high-level waste slurries are combined during processing steps that ultimately produce a stable borosilicate glass waste form. Chemically treated waste slurries are combined with each other and with glass frit-water slurries to produce the melter feed. Understanding the evolution of the rheological properties of the slurries is an important aspect of removing and treating the stored waste. To a first approximation, combinations of colloidal waste slurry with {approx}0.1-mm mean diameter glass frit or glass beads act in an analogous matter to slurries of spherical beads in Newtonian liquids. The non-Newtonian rheological properties of the waste slurries without frit, however, add complexity to the hydrodynamic analysis. The use of shear rate dependent apparent viscosities with the modified Einstein equation was used to model the rheological ...

2009-09-02

400

Proceedings of the eighth annual DOE low-level waste management forum: Technical Session 6, Waste treatment  

Energy Technology Data Exchange (ETDEWEB)

Nine papers in this proceedings have been processed for inclusion in the Energy Data Base. (AT)

1987-02-01

401

Nuclear waste plans enter critical phase  

Energy Technology Data Exchange (ETDEWEB)

A brief article considers the possible result of the enquiry into Nirex`s plan to build an underground rock laboratory at Sellafield in relation to radioactive waste disposal in the UK. (UK).

1996-10-31

402

Nuclear power plant liquid waste solidification system. [Japan  

Energy Technology Data Exchange (ETDEWEB)

The fundamental points to be considered in a waste treatment system for a country like Japan, where the final disposal method has not been decided and the wastes have to be stored in the power plants, are volume reduction of the wastes, safe storage of the wastes in the plant, and flexibility regarding the final disposal. A system has been developed that consists of a thin film evaporator for the direct solidification of the liquid waste, a pelletizer for producing hard pellets from the powdered wastes, a pellet storage unit, and a solidification unit for the final disposal. A pilot plant with waste treatment capacity of 200 kg/h was built in 1976 and has proved the system feasibility. This paper reports on pilot plant tests of the thin film evaporator and other components, tests on pellet deterioration during long term storage, and ...

1981-01-01

403

Nuclear power plant liquid waste solidification system  

International Nuclear Information System (INIS)

The fundamental points to be considered in a waste treatment system for a country like Japan, where the final disposal method has not been decided and the wastes have to be stored in the power plants, are volume reduction of the wastes, safe storage of the wastes in the plant, and flexibility regarding the final disposal. A system has been developed that consists of a thin film evaporator for the direct solidification of the liquid waste, a pelletizer for producing hard pellets from the powdered wastes, a pellet storage unit, and a solidification unit for the final disposal. A pilot plant with waste treatment capacity of 200 kg/h was built in 1976 and has proved the system feasibility. This paper reports on pilot plant tests of the thin film evaporator and other components, tests on pellet deterioration during long term storage, and ...

1981-02-26

404

Nondestructive characterization of low-level transuranic waste  

Energy Technology Data Exchange (ETDEWEB)

The use of nondestructive evaluation (NDE) methods is proposed for characterization of transuranic (TRU) waste stored at the Radioactive Waste Management Complex. These NDE methods include real-time x-ray radiography, real-time neutron radiography, x-ray and neutron computed tomography, thermal imaging, container weighing, visual examination, and acoustic measurements. An integrated NDE system is proposed for characterization and certification of TRU waste destined for eventual shipment to the Waste Isolation Pilot Plant in New Mexico. Methods for automating both the classification waste and control of a complete nondestructive evaluation/nondestructive assay system are presented. Feasibility testing of the different NDE methods, including real-time x-ray radiography, and development of automated waste classification techniques are covered as part of a five year ...

1981-10-01

405

NASA - Waste Not  

Science.gov (United States)

Jun 4, 2004 ... On a two-year trip to Mars, according to one estimate, a crew of six humans will generate more than six tons of solid organic waste--much of ...

406

NAME=\\  

Wastenet

... Waste Collection Systems Products and Equipment Find and compare a variety of waste collection systems products and equipment on the world's largest environmental industry portal. View product ...

407

Mixed waste disposal facility at the Nevada Test Site  

Energy Technology Data Exchange (ETDEWEB)

This report provides a brief overview of the history and planning for a proposed mixed waste disposal site on the Nevada Test Site. 8 figs.

1987-01-01

408

Kraft pulping of industrial wood waste  

Science.gov (United States)

Jun 16, 2011 ... Description: Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for ...

409

Fish waste - NASA Quest  

Science.gov (United States)

Seriously, generally fish waste does drop, but quite slowly. But a good group of snails should still do a fine job of cleaning the tank. ...

410

Factoring Potential Accelerator Transmutation of Waste Demonstrations into Accelerator Production of Tritium Design Planning  

CERN Document Server

Factoring Potential Accelerator Transmutation of Waste Demonstrations into Accelerator Production of Tritium Design Planning

1998-01-01

411

Converting Simulated Sodium-bearing Waste into a Single Solid Waste Form by Evaporation: Laboratory- and Pilot-Scale Test Results on Recycling Evaporator Overheads  

Energy Technology Data Exchange (ETDEWEB)

Conversion of Idaho National Engineering and Environmental Laboratory radioactive sodium-bearing waste into a single solid waste form by evaporation was demonstrated in both flask-scale and pilot-scale agitated thin film evaporator tests. A sodium-bearing waste simulant was adjusted to represent an evaporator feed in which the acid from the distillate is concentrated, neutralized, and recycled back through the evaporator. The advantage to this flowsheet is that a single remote-handled transuranic waste form is produced in the evaporator bottoms without the generation of any low-level mixed secondary waste. However, use of a recycle flowsheet in sodium-bearing waste evaporation results in a 50% increase in remote-handled transuranic volume in comparison to a non-recycle flowsheet.

2004-01-01

412

Acid Waste Equipment on Environmental Expert  

Wastenet

...Systems by IPEX Enfield electrofusion acid waste systems give you the proven corrosion resistance of polypropylene, along with our patented, state-of-the-art electrofusion system....

414

Metal finishing and vacuum processes groups, Materials Fabrication Division progress report, March-May 1984  

Energy Technology Data Exchange (ETDEWEB)

Progress is reported in fabrication and coating activities being conducted for the weapons program, nuclear test program, nuclear design program, magnetic fusion program, and miscellaneous applications. (DLC)

1984-07-11

416

Executive Development Journeys The Essence of Customized Programs  

CERN Document Server

Summarizing the three main reasons why customized programs are commissioned, this book explains and explores the key aspects of successful development programs, with views from corporate sponsors, participants, faculty contributors and case studies of customised programs commissioned by 6 organizations

2010-01-01

417

Energy Management and Conservation Program: Fiscal Year 2005 Annual Report  

Wastenet

Keywords: energy, management, conservation, program, fiscal, year, 2005, annual, ...S Environmental Protection Agency Energy Management and Conservation Program ...ENVIRONMENTAL P ROTECTION AGENCY Energy Management and Conservation Program Fiscal Year 2005 Annual Report

422

HARPHRQ. A Geochemical Speciation Program Based on PHREEQE  

Energy Technology Data Exchange (ETDEWEB)

HARPHRQ is a geochemical speciation program developed at Harwell and based on the U.S. Geological Survey code Phreeqe.

1992-02-18

423

Geothermal Energy R&D Program Summary  

Energy Technology Data Exchange (ETDEWEB)

This is an internal DOE Geothermal Program planning and control document. Many of these reports were issued only in draft form.

1988-11-18

424

Energy Engineering Analysis Program (EEAP), Cornhusker ...  

Science.gov (United States)

... is to develop a systematic program of energy consumption reductions in compliance with the stated goals of the Army Facilities Energy Plan (AFEP ...

1984-03-01

425

A Program Manager's Guide for Software Cost Estimating  

Science.gov (United States)

... A PROGRAM MANAGER'S GUIDE FOR SOFTWARE COST ESTIMATING ... This thesis provides a broad view of the software cost estimating process. ...

2002-12-01

426

Review of high-level waste form properties. [146 bibliographies  

Energy Technology Data Exchange (ETDEWEB)

This report is a review of waste form options for the immobilization of high-level-liquid wastes from the nuclear fuel cycle. This review covers the status of international research and development on waste forms as of May 1979. Although the emphasis in this report is on waste form properties, process parameters are discussed where they may affect final waste form properties. A summary table is provided listing properties of various nuclear waste form options. It is concluded that proposed waste forms have properties falling within a relatively narrow range. In regard to crystalline versus glass waste forms, the conclusion is that either glass of crystalline materials can be shown to have some advantage when a single property is considered; however, at this date no single waste form offers optimum ...

1980-12-01

428

Waste management facilities cost information for hazardous waste. Revision 1  

Energy Technology Data Exchange (ETDEWEB)

This report contains preconceptual designs and planning level life-cycle cost estimates for managing hazardous waste. The report`s information on treatment, storage, and disposal modules can be integrated to develop total life-cycle costs for various waste management options. A procedure to guide the US Department of Energy and its contractor personnel in the use of cost estimation data is also summarized in this report.

1995-06-01

429

Waste Diversion | Greening EPA | US EPA  

Wastenet

...diversion generates a host of environmental, financial, and social benefits, including conserving energy, reducing disposal costs, and reducing the burden on landfills and other waste disposal methods . Waste Diversion at EPA For many years, EPA has established waste diversion goals that exceed current federal requirements. EPA ...

430

Utilization of plastic wastes in a blast furnace - a contribution to ecological and economical recycling of plastic wastes; Kunststoffverwertung im Hochofen - ein Beitrag zum oekologischen und oekonomischen Recycling von Altkunststoffen  

Energy Technology Data Exchange (ETDEWEB)

This article describes the utilization of plastic wastes in a blast furnace. The plastic waste is a substitution for petroleum and coal as a raw material for synthesis gas production. The synthesis gas is the reducing agent in the blast furnace for the reduction of iron ores. You can find here an ecological and economical analysis of this process in comparison to the utilization of petroleum and coal. (SR)

1996-12-31

434

Resources | Environment Knowledge Hub  

Wastenet

... MUNICIPAL SOLID WASTES (MANAGEMENT AND HANDLING) RULES, 2000 Plastic Bag ban in Dhaka City, Bangladesh Private Sector Participation in Municipal Solid Waste Management SKAT 2000 TECHNICAL GUIDELINES ON MUNICIPAL SOLID WASTE MANAGEMENT Hazardous Waste Management Unit, Environmental Pollution Control Division, Central Environmental Authority, Sri Lanka 2004 Subregional ...

435

Request for interim approval to operate 218-E-12B Trench 94 as a chemical waste landfill for disposal of polychlorinated biphenyl wastes in submarine reactor compartments. Revision 1.  

Science.gov (United States)

This request is submitted to seek interim approval to operate a chemical waste landfill for the disposal of polychlorinated biphenyl (PCB) waste. Interim approval is requested for a period not to exceed 5 years. This request covers only the disposal of sm...

1992-01-01

440

Oil refinery waste disposal methods, quantities and costs, 1993 survey  

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the information gathered by CONCAVE in a 1993 survey of waste generation and disposal by the oil refineries in Western Europe. The survey covered the types of waste produced, their quantities, disposal routes and costs of disposal. The results are compared with those from a 1986 survey, but because of the increased numbers of refineries reporting, comparison is difficult. The survey revealed wide variations in disposal costs depending on waste type and local circumstances.

1995-06-01

442

Methane fermentation of agricultural wastes and domestic animal's wastes  

Energy Technology Data Exchange (ETDEWEB)

Cattle and pig wastes, orange peels, compost, and grain husks were hydrolyzed in an alkaline medium to investigate the CH4 generation capacity. The respective CH4 production capacities from pig wastes and rice hulls were approximately 1 and approximately 0.1 L/g. The CH4 produced can be used to supplement energy requirements of farms.

1981-01-01

448

Idaho National Engineering Laboratory Nonradiological Waste Management Information for 1992 and record to date  

Energy Technology Data Exchange (ETDEWEB)

This document provides detailed data and graphics on airborne and liquid effluent releases, fuel oil and coal consumption, water usage, and hazardous and mixed waste generated for calendar year 1992. This report summarizes industrial waste data records compiled since 1971 for the Idaho National Engineering Laboratory (INEL). The data presented are from the INEL Nonradiological Waste Management Information System.

1993-08-01

449

GS1 - radiological protection objectives for the disposal of solid radioactive wastes  

Energy Technology Data Exchange (ETDEWEB)

A summary is given of the 1983 NRPB-GS1 Report on the 'Radiological protection objectives for the disposal of solid radioactive wastes'. The two principal difficulties in applying the ICRP system of dose limitation to some solid waste disposal methods are outlined. Despite these difficulties three radiological protection objectives for waste disposal were recommended based on the same fundamental principle as ICRP recommendations.

1984-01-01

450

Estimation of animal and olive solid wastes in Jordan and their potential as a supplementary energy source: An overview  

Energy Technology Data Exchange (ETDEWEB)

Biomass is a potential source of energy that can reduce our dependency on oil as the main source of energy. In addition to municipal solid waste, animal and olive wastes are the main sources of organic waste in Jordan. In 2005, there were more than 2.4 million heads of sheep, about 72 thousand cows, and 40 million hens being raised in farms distributed in all governorates of Jordan. These animals produce 5.3 million tons (as exerted) of solid waste per year. If these quantities can be effectively collected they may constitute a valuable source of energy. This paper is aiming to estimate the amounts of animal and solid wastes generated in Jordan and their energy potential. The total amount of BOD from animal waste is estimated at 200,000 tons per year. Significant quantities of organic waste can also be collected from olive mills distributed ...

2010-10-15

451

Environmental assessment of coal waste mounds in Japan using remote sensing techniques  

Energy Technology Data Exchange (ETDEWEB)

Focuses on the application of remote sensing techniques to the study of coal waste mounds. The situation at the coal waste mounds in Fukuoka, Japan is cited. Guidelines on film parameters, photographic keys and tasks required to inventory, monitor and manage coal waste mounds in Japan are addressed. Application of photogrammetry, remote sensing, aerial photography and satellite imagery techniques in monitoring spoil banks is reviewed. Applicability of the techniques is discussed. 24 refs.

1993-01-01

452

Energy recovery from waste by use of fluidized-bed technology  

Energy Technology Data Exchange (ETDEWEB)

Revolving type fluidized-bed technology, developed by Ebara Corp., is installed in more than 100 facilities worldwide. The technology is applied for waste, coal and in situations where a conventional fluidized bed is difficult to use. Waste and/or coal can be treated and valuable energy can be recovered from a non-renewable source. This paper describes the application of the revolving fluidized bed for waste, coal and tyres.

1999-07-01

454

Decommissioning of facility for use of radioisotopes on waste management and disposal facility  

Energy Technology Data Exchange (ETDEWEB)

All the tests have been finished up in the Waste Management and Disposal Facility which has been used for the safety tests of solidified radioactive waste on sea dumping disposal. The decommissioning of this facility was performed for use of radioisotopes. This report describes the plan on decommissioning of facility for use of radioisotopes, the contamination checking methods and measurement of radioactivity, the fore case and practice for amount of generated radioactive wastes, the operation procedures for dismantlement, the safety measures, the expenses for decommissioning and so on. (author)

1999-09-01

456

Characterisation of long-lived low and intermediate-level radioactive wastes in the Nordic Countries  

International Nuclear Information System (INIS)

The present report is final report from a study on characterisation of radioactive waters in the Nordic countries. The study has mainly been focused on long-lived low and intermediate level radioactive waste. Methods to measure or estimate the activity content and the general composition are discussed. Recommendations are given regarding characterisation of waste under treatment and characterisation of already produced waste packages. (au).

2005-01-01

457

CONVERTING WASTE  

Wastenet

condenser, gas refiner, oil (gas) storage tank and dual fuel engine

458

BC  

Wastenet

criteria which would constitute environmentally sound management of mobile phone waste in accordance with the Basel Convention;

459

BC  

Wastenet

all Certified ESM facilities capable of receiving used mobile phone waste from non-Annex VII countries.

460

Achievements and Perspectives of the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management  

International Nuclear Information System (INIS)

The Joint Convention on the Safety of Spent Fuel management and on the Safety of Radioactive Waste Management is the first legal instrument to directly address the safety of spent fuel and radioactive waste management on a global scale. The Joint Convention entered into force in 2001. This paper describes its process and its main achievements to date. The perspectives to establish of a Global Waste Safety Regime based on the Joint Convention are also discussed. (authors)

462

Negotiating equity for management of DOE wastes  

Energy Technology Data Exchange (ETDEWEB)

One important factor frustrating optimal management of Department of Energy (DOE)-complex wastes is the inability to use licensed and permitted facilities systematically. Achieving the goal of optimal use of DOE`s waste management facilities is politically problematic for two reasons. First, no locale wants to bear a disproportionate burden from DOE wastes. Second, the burden imposed by additional wastes transported from one site to another is difficult to characterize. To develop a viable framework for equitably distributing these burdens while achieving efficient use of all DOE waste management facilities, several implementation and equity issues must be addressed and resolved. This paper discusses stakeholder and equity issues and proposes a framework for joint research and action that could facilitate equity negotiations among stakeholder and move toward a more optimal use of ...

1994-09-01

463

Low-level Waste Forum meeting report. Winter meeting, January 26--28, 1994  

Energy Technology Data Exchange (ETDEWEB)

The Low-Level Radioactive Waste Forum is an association of representatives of states and compacts established to facilitate state and compact commission implementation of the Low-Level Radioactive Waste Policy Act of 1980 and the Low-Level Radioactive Waste Policy Amendments Act of 1985 and to promote the objectives of low-level radioactive waste regional compacts. The Forum provides an opportunity for states and compacts to share information with one another and to exchange views with officials of federal agencies. The Forum participants include representatives from regional compacts, designated host states, unaffiliated states, and states with currently-operating low-level radioactive waste facilities. This report contains information synthesizing the accomplishments of the Forum, as well as any new advances that have been made in the management of low-level radioactive ...

1994-12-31

464

Liquid radioactive waste discharges from B plant to cribs  

Energy Technology Data Exchange (ETDEWEB)

This engineering report compiles information on types and quantities of liquid waste discharged from B-Plant directly to cribs, ditches, reverse wells, etc., that are associated with B-Plant. Waste discharges to these cribs via overflow form 241-B, 241-BX, and 241-BY tank farms, and waste discharged to these cribs from sources other than B-Plant are discussed.Discharges from B-Plant to other cribs, unplanned releases, or waste remaining in tanks are not included in the report. Waste stream composition information is used to predict quantities of individual chemicals sent to cribs. This provides an accurate mass balance of waste streams from B-Plant to these cribs. These predictions are compared with known crib inventories as a verification of the process.

1996-05-29

465

Disposal of De-ionizer Vessels Highly Contaminated with 14Carbon at SRS  

International Nuclear Information System (INIS)

At the Savannah River Site (SRS), nuclear production reactors used de-ionizers to control the chemistry of the reactor moderator during their operation to produce nuclear materials primarily for the weapons program. These de-ionizers were removed from the reactors and stored as a legacy waste with no path to disposal due to the relatively high 14C contamination (i.e., on the order of 20 curies per de-ionizer for 48-50 de-ionizers) and the low disposal limit of 4.2 Ci previously established for the Intermediate Level Vault (ILV). The ILV is considered most appropriate facility within which to dispose these items due to the method of solidifying waste items with cementitious material inside concrete vaults. In previous analyses the 14C ILV disposal limit was established at 4.2 Ci resulting from the use of a very conservative method to analyze the dose received from atmospheric releases of gaseous 14C. This investigation ...

2008-01-01

466

Theory and evidence of economies of scale in the development of waste management systems  

Energy Technology Data Exchange (ETDEWEB)

Waste is a cost of doing business. This cost can be considered in terms of the potential adverse health and environmental impacts, or the waste management costs associated with avoiding, minimizing, and controlling those impacts. There is an anticipated increase in the cost of waste management as a result of the increasing requirements for regulatory compliance. To meet the total waste management capacity needs of the organization and the compliance requirements, low-level radioactive, hazardous, and mixed waste management will need demonstrated technologies strategically managed as a technology portfolio. The role of the decision maker is to select the optimum mix of technologies and facilities to provide the waste management capacity needed for the next twenty years. The waste management system resulting from this mix includes multiple ...

1989-01-01

467

The control of radioactive wastes and the quality assurance requirements  

International Nuclear Information System (INIS)

For prolonged storage and eventual disposal radioactive wastes will be solidified to reduce the problems which accompany liquid waste whilst solid wastes will be encapsulated in an immobilising matrix. In the solidification and encapsulation process it will be important to produce a material in a form which is chemically stable, mechanically strong and which will not react with or allow free passage of groundwater. To this end a continuous check will be required to ensure that the various wastes are chemically compatible with the solidifying and binding matrices and that the associated processes are performed against a strict Quality Programme. The Quality Programme will be extensive requiring the specification of procedures for assessing the quality and nature of the wastes, the detailed operation of the solidification and/or encapsulation, the overpack requirements for ...

468

The Los Alamos National Laboratory Transuranic Waste Retireval Project  

Energy Technology Data Exchange (ETDEWEB)

This paper presents the status of the Los Alamos National Laboratory (LANL) project for remediation of transuranic (TRU) and TRU mixed waste from Pads 1, 2, and 4. Some of the TRU waste packages retrieved from Pad I are anticipated to be part of LANL`s initial inventory to be shipped to the Waste Isolation Pilot Plant (WIPP) in April 1998. The TRU Waste Inspectable Storage Project (TWISP) was initiated in February 1993 in response to the New Mexico Environment Department`s (NMED`s) Consent Agreement for Compliance Order, ``New Mexico Hazardous Waste Agreement (NMHWA) 93-03.`` The TWISP involves the recovery of approximately 16,865 TRU and TRU-mixed waste containers currently under earthen cover on Pads 1, 2, and 4 at Technical Area 54, Area G, and placement of that waste into inspectable storage. All waste will be moved ...

1997-02-01

469

Influence of temperature on strength of cemented surrogate nitrate salt waste  

Energy Technology Data Exchange (ETDEWEB)

The Rocky Flats Plant (RFP) generates large volumes of a low level aqueous waste stream high in nitrate salts. The aqueous waste is concentrated by evaporation and then mixed with Portland cement prior to transport and disposal. Planned process upgrades include a new horizontal thin film evaporator. Temperature of brine at discharge end of the new evaporator will be near boiling point. Introduction of hot water to cement can degrade the monolithic waste form. However, the RFP salt waste contains high concentrations of compounds known to retard hydration. This paper discusses impact of introducing high temperature waste to cement. The study evaluated three waste compositions: (1) highest probable nitrate composition, (2) highest probable chloride composition, and (3) current composition. Results showed that compressive strength of final waste ...

1993-01-01

470

Influence of temperature on strength of cemented surrogate nitrate salt waste  

Energy Technology Data Exchange (ETDEWEB)

The Rocky Flats Plant (RFP) generates large volumes of a low level aqueous waste stream high in nitrate salts. The aqueous waste is concentrated by evaporation and then mixed with Portland cement prior to transport and disposal. Planned process upgrades include a new horizontal thin film evaporator. Temperature of brine at discharge end of the new evaporator will be near boiling point. Introduction of hot water to cement can degrade the monolithic waste form. However, the RFP salt waste contains high concentrations of compounds known to retard hydration. This paper discusses impact of introducing high temperature waste to cement. The study evaluated three waste compositions: (1) highest probable nitrate composition, (2) highest probable chloride composition, and (3) current composition. Results showed that compressive strength of final waste ...

1993-03-01

471

DWPF waste form compliance plan (Draft Revision)  

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy currently has over 100 million liters of high-level radioactive waste in storage at the Savannah River Site (SRS). In the late 1970's, the Department of Energy recognized that there were significant safety and cost advantages associated with immobilizing the high-level waste in a stable solid form. Several alternative waste forms were evaluated in terms of product quality and reliability of fabrication. This evaluation led to a decision to build the Defense Waste Processing Facility (DWPF) at SRS to convert the easily dispersed liquid waste to borosilicate glass. In accordance with the NEPA (National Environmental Policy Act) process, an Environmental Impact Statement was prepared for the facility, as well as an Environmental Assessment of the alternative waste forms, and issuance of a Record of Decision (in December, 1982) on ...

1991-01-01

472

DWPF waste form compliance plan (Draft Revision)  

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy currently has over 100 million liters of high-level radioactive waste in storage at the Savannah River Site (SRS). In the late 1970`s, the Department of Energy recognized that there were significant safety and cost advantages associated with immobilizing the high-level waste in a stable solid form. Several alternative waste forms were evaluated in terms of product quality and reliability of fabrication. This evaluation led to a decision to build the Defense Waste Processing Facility (DWPF) at SRS to convert the easily dispersed liquid waste to borosilicate glass. In accordance with the NEPA (National Environmental Policy Act) process, an Environmental Impact Statement was prepared for the facility, as well as an Environmental Assessment of the alternative waste forms, and issuance of a Record of Decision (in December, 1982) on the ...

1991-12-31

473

Analysis of options for coal combustion waste management in the Pacific Basin  

Energy Technology Data Exchange (ETDEWEB)

Many Pacific Basin countries rely on oil for electricity production. Alternative fuel sources such as coal, which is available in the Pacific Basin, can help mitigate adverse impacts of sudden price increases or supply disruptions. Coal combustion produces solid and potentially hazardous wastes of concern to environmental regulators and utility managers. This paper identifies issues associated with managing coal combustion wastes in the Pacific Basin, using the state of Hawaii as a case study. Hawaii is typical of many Pacific Basin locations in that it depends on oil, has limited sites, for waste management operations, and is subject to domestic and international waste management regulations. The paper discusses coal-fired utility wastes, environmental impacts of coal combustion waste disposal, and regulatory requirements that impact coal ...

1993-10-01

474

Characterization of an improved disposal site for low and intermediate level waste using Cs-137 deposition profiles  

International Nuclear Information System (INIS)

According to the present concept, the low and intermediate level wastes generated during the Cernavoda NPP operation will be disposed in a near surface repository. The Saligny site, placed in the NPP protected area, has been proposed for their disposal. Geologically, the main components of this site are the quaternary loess, the Precambrian and Pre-quaternary clays, the Eocene and Barremian limestone. Hydrologically, the site can be divided into a vadose zone down to 45-50 m and three distinct aquifers, two of them in the limestone beds and the third in the lenses of sand and limestone existing in the pre-quaternary clay layer. A large research program for site characterization was initiated in 1996. At present, the site characteristics requested for safety analysis have been experimentally measured on soil samples or calculated by different computer programs. Hundreds of experimental values of the density, porosity, ...

2004-09-09

475

Yucca Mountain, Nevada - A Proposed Geologic Repository for High-Level Radioactive Waste (Volume 1) Introduction  

Energy Technology Data Exchange (ETDEWEB)

Yucca Mountain in Nevada represents the proposed solution to what has been a lengthy national effort to dispose of high-level radioactive waste, waste which must be isolated from the biosphere for tens of thousands of years. This chapter reviews the background of that national effort and includes some discussion of international work in order to provide a more complete framework for the problem of waste disposal. Other chapters provide the regional geologic setting, the geology of the Yucca Mountain site, the tectonics, and climate (past, present, and future). These last two chapters are integral to prediction of long-term waste isolation.

2006-09-25

476

Waste plastic treatment equipment; Hai plastic shori sochi  

Energy Technology Data Exchange (ETDEWEB)

In recent years, there has been increasing demand for resource-recycling of waste plastic, especially due to the introduction of legislation on recycling of materials used for packages of household goods. Methods of recycling waste plastic from household goods are currently still under development, and appropriate techniques to deal with such waste are required. Toshiba has developed a technique to dehydrochlorinate plastic containing polyvinyl chloride (PVC). This paper introduces our petrolization and dehydrochlorination system for waste plastic containing PVC. (author)

1999-04-01

477

Waste management systems model for energy systems sites on the Oak Ridge Reservation  

Energy Technology Data Exchange (ETDEWEB)

There is a model on the Oak Ridge Reservation which provides requirements for determining capacities and capabilities related to low-level, hazardous, and mixed wastes. In FY 1987, the model will be sufficiently advanced to provide various waste management scenarios. These scenarios will be compared technically, operationally, and financially by use of waste characterization data and process simulators that are currently under development. The results of the process simulations will be used to help identify waste treatment, storage, and disposal technologies that need to be demonstrated prior to full-scale development for DOE use. The information derived from this effort will be made available to all DOE facilities.

1986-01-01

478

Vitrification of waste  

Energy Technology Data Exchange (ETDEWEB)

A method for encapsulating and immobilizing waste for disposal. Waste, preferably, biologically, chemically and radioactively hazardous, and especially electronic wastes, such as circuit boards, are placed in a crucible and heated by microwaves to a temperature in the range of approximately 300{degrees}C to 800{degrees}C to incinerate organic materials, then heated further to a temperature in the range of approximately 1100{degrees}C to 1400{degrees}C at which temperature glass formers present in the waste will cause it to vitrify. Glass formers, such as borosilicate glass, quartz or fiberglass can be added at the start of the process to increase the silicate concentration sufficiently for vitrification.

1992-12-31

479

Projected radionuclide inventories of DWPF glass from current waste at time of production. Revision 1  

Energy Technology Data Exchange (ETDEWEB)

The Waste Acceptance Preliminary Specifications (WAPS) require that the DWPF estimate the inventory of long-lived radionuclides present in the waste glass, and report the values in the Waste Form Qualification Report. In this report, conservative (biased high) estimates of the radionuclide inventory of glass produced from waste currently in the Tank Farm are provided. In most cases, these calculated values compare favorably with actual data. In those cases where the agreement is not good, the values reported here are conservative.

1993-02-04

480

Process and system for treatment of radioactive waste  

Energy Technology Data Exchange (ETDEWEB)

In a treatment system of radioactive waste solution including sodium sulfate generated from a boiling water type nuclear reactor, waste solution is fed into a thin film evaporator where the waste solution is evaporated and made into powder while precipitating in a peripheral surface of the evaporator vessel. The surface of the precipitated solid is wiped by rotating wiper blades and removed off as radioactive solid powder. The rotational speed of a rotor to which the wiper blades are secured is controlled at a minimum and necessary rotational speed which contributes to make the waste solution into the powder so that the rate of worn out of the wiper blade is decreased.

1985-07-02

481

PFP dangerous waste training plan  

Science.gov (United States)

This document establishes the minimum training requirements for the Plutonium Finishing Plant (PFP) personnel who are responsible for management of dangerous waste. The training plan outlines training requirements for handling of solid dangerous waste during generator accumulation and liquid dangerous waste during treatment and storage operations. The implementation of this training plan will ensure the PFP facility compliance with the training plan requirements of Dangerous Waste Regulation. Chapter 173-303-330. Washington Administrative Code (WAC). The requirements for such compliance is described in Section 11.0 of WHC-CM-7-5 Environmental Compliance Manual.

1996-01-01

482

Material-not-categorized-as-waste survey for 1992  

Energy Technology Data Exchange (ETDEWEB)

In October 1992, the US Department of Energy, Richland Field Office (RL) requested that Westinghouse Hanford Company (WHC) respond to a letter from EM-331 asking for completion of a survey of items in storage but not categorized as waste (Roberts 1992). The letter contained an attachment with instructions on how to fill out the attached form and what to exclude from the survey (Appendix A). This report is a summary of the information from the response issued to RL. This report primarily is for use in estimating future waste volumes that may have been overlooked because of the nature of their classification as material not categorized as waste (MNCAW) (i.e., not yet declared Waste).

1993-07-01

483

Mastery of risks: we build the memory of radioactive waste disposal facilities  

International Nuclear Information System (INIS)

The ANDRA, the French national agency of radioactive wastes, is organizing today the information needs of tomorrow. The aim is to allow the future generations to have access to the knowledge of the existence of subsurface radioactive waste facilities and to understand the context and technologies of such facilities. The storage of this information is made on 'permanent paper', a high resistant paper with a lifetime of 600 to 1000 years. An updating of these data is made every 5 years for each waste disposal center. Another project, still in progress, concerns the memory management of deep geologic waste disposal facilities for which the time scale to be considered is of the order of millennia. (J.S.)

484

Co-processing; Waste-derived fuels help solve compliance problems and produce usable materials  

Energy Technology Data Exchange (ETDEWEB)

An estimated 265 million tons of hazardous waste are generated annually in the United States. Traditional waste disposal methods are inadequate, and many are no longer environmentally acceptable. Still, the waste increases along with demands for clean, environmentally safe methods for dealing with it. Faced with these demands, many hazardous waste generators are turning for help to co-processing,'' technology that goes beyond a no-impact solution to one of net positive impact, both environmentally and economically. This paper describes co-processing.

1990-01-01

485

Aqueous radioactive waste bituminization  

International Nuclear Information System (INIS)

The bituminzation of decontamination and ion exchange resin stripping wastes with four grades of asphalt was investigated to determine the effects of asphalt type on the properties of the final products. All waste forms deformed readily under light loads indicating they would flow if not restrained. It was observed in all cases that product leaching rates increased as the hardness of the asphalt used to treat the waste increased. If bituminization is adopted for any Ontario Hydro aqueous radioactive wastes they should be treated with soft asphalt to obtain optimum leaching resistance and mechanical stability during interim storage should be provided by a corrosion resistant container.

5049-01-01

486

Anaerobic digestion of municipal solid waste: Technical developments  

Energy Technology Data Exchange (ETDEWEB)

The anaerobic biogasification of organic wastes generates two useful products: a medium-Btu fuel gas and a compost-quality organic residue. Although commercial-scale digestion systems are used to treat municipal sewage wastes, the disposal of solid organic wastes, including municipal solid wastes (MSW), requires a more cost-efficient process. Modern biogasification systems employ high-rate, high-solids fermentation methods to improve process efficiency and reduce capital costs. The design criteria and development stages are discussed. These systems are also compared with conventional low-solids fermentation technology.

1996-01-01

487

DECONTAMINATION SYSTEMS AND INFORMATION RESEARCH PROGRAM  

Energy Technology Data Exchange (ETDEWEB)

During the five plus years this Cooperative Agreement existed, more than 45 different projects were funded. Most projects were funded for a one year period but there were some, deemed of such quality and importance, funded for multiple years. Approximately 22 external agencies, businesses, and other entities have cooperated with or been funded through the WVU Cooperative Agreement over the five plus years. These external entities received 33% of the funding by this Agreement. The scope of this Agreement encompassed all forms of hazardous waste remediation including radioactive, organic, and inorganic contaminants. All matrices were of interest; generally soil, water, and contaminated structures. Economic, health, and regulatory aspects of technologies were also within the scope of the agreement. The highest priority was given to small businesses funded by the Federal Energy Technology Center (FETC) and Department of Energy (DOE) involved in research and development ...

1998-11-01

488

Critical Educational Program Components for Students with Emotional and Behavioral Disorders: Science, Policy, and Practice  

Science.gov (United States)

In spite of recent education reform and reorganization efforts requiring the use of research-based methods, the fundamental elements of an effective program for children and youth with emotional and behavioral disorders (EBD) have not been succinctly identified. This article presents the essential features of programs for students with EBD. Program elements include (a) qualified and committed professionals, (b) utilitarian environmental supports, (c) effective behavior management plans, (d) valid social skill and social interpretation training and social interaction programs, (e) proven academic support systems, (f) strong parent- and family-involvement programs, (g) coordinated community support mechanisms, and (h) ongoing evaluation of essential program components and student outcomes and progress. A justification for the program and a ...

2010-12-01

489

The Waste Management Plan integration into Decommissioning Plan of the WWR-S research reactor from Romania  

International Nuclear Information System (INIS)

The paper presents the progress of the Radioactive Waste Management Plan which accompanies the Decommissioning Plan for research reactor WWR-S located in Magurele, Ilfov, near Bucharest, Romania. The new variant of the Decommissioning Plan was elaborated taking into account the IAEA recommendation concerning radioactive waste management. A new feasibility study for WWR-S decommissioning was also developed. The preferred safe management strategy for radioactive wastes produced by reactor decommissioning is outlined. The strategy must account for reactor decommissioning, as well as rehabilitation of the existing Radioactive Waste Treatment Plant and the upgrade of the Radioactive Waste Disposal Facility at Baita-Bihor. Furthermore, the final rehabilitation of the laboratories and reusing of cleaned reactor building is envisaged. An inventory of each type of radioactive ...

2008-05-28

490

Solidification of DOE problem wastes  

Energy Technology Data Exchange (ETDEWEB)

Sodium nitrate waste has been successfully solidified in two types of polymeric materials: polyethylene, a thermoplastic material, and polyester styrene (PES), a thermosetting material. Waste form property evaluation tests such as ANS 16.1 leaching test and compressive strength measurements were performed on the waste forms containing various amounts of sodium nitrate. A single-screw extruder was employed for incorporating dry waste into polyethylene at its melt temperature of 120/sup 0/C to produce a homogenous mixture. Results of the leaching test for polyethylene waste forms containing 30, 50, 60 and 70 wt% sodium nitrate are presented as cumulative fraction leached and leaching indices ranging from 11 to 7.8. Two PES systems are discussed. The first is for solidification of dry salt wastes and the second is a water extendible system that is compatible with ...

1986-01-01

491

Recycling of waste polymeric materials using ionizing radiation techniques for possible applications and practical uses  

International Nuclear Information System (INIS)

recycling of waste polypropylene (WPP) and waste rubber (WR) originated from rejected worn-out tires present very important problem due to their huge amount and their negative impact on environment. many communities in the world are struggling with this problem of how to manage waste disposal, in order to eliminate or reduce waste rubber from the environment and to reduce costs of some rubber and polypropylene articles. trials to reuse waste rubber and waste polypropylene, have encountered some difficulties.such two substrate polymers differ from each other in nature, since waste polypropylene is thermoplastic while waste rubber exists in thermosetting state. accordingly, the study and use of their mixtures should be very interesting.the aim of this work is to modify the physical and chemical properties of WR and WPP ...

2007-01-01

492

Recycling of plastic waste in blast furnace; Koro ni okeru hai plastic riyo gijutsu  

Energy Technology Data Exchange (ETDEWEB)

Features particular to the technology of using a blast furnace for the recycling of plastic waste are reported, and the behavior of plastic waste injected into a blast furnace is described. The plastic waste is injected into the furnace borne on a 1200degC hot blast through the tuyere. The plastic is converted into a reducing gas in the furnace, and the gas on its way up in the furnace is utilized as a reducing agent in the iron ore reducing reaction. The process is described below. All kinds of plastic waste may be utilized in this fashion, with the exception of polyvinyl chloride. As for polyvinyl chloride, efforts are under way to develop a technology to recycle this plastic. The method using the blast furnace tolerates a wide range of impurities, and the plastic waste is only to be crushed and granulated before use in the furnace. Plastic waste coarsely ...

1998-05-20

493

Process development for remote-handled mixed-waste treatment  

Energy Technology Data Exchange (ETDEWEB)

The Oak Ridge National Laboratory (ORNL) is developing a treatment process for remote-handled (RH) liquid transuranic mixed waste governed by the concept of minimizing the volume of waste requiring disposal. This task is to be accomplished by decontaminating the bulk components so the process effluent can be disposed with less risk and expense. Practical processes have been demonstrated on the laboratory scale for removing cesium 137 and strontium 90 isotopes from the waste, generating a concentrated waste volume, and rendering the bulk of the waste nearly radiation free for downstream processing. The process is projected to give decontamination factors of 10{sup 4} for cesium and 10{sup 3} for strontium. Because of the extent of decontamination, downstream processing will be contact handled. The transuranic, radioactive fraction of the mixed waste stream will ...

1990-01-01

494

Liquid waste evaporator operating experience  

Energy Technology Data Exchange (ETDEWEB)

Atomic Energy of Canada Limited (AECL) operates the Waste Treatment Centre (WTC) to treat and immobilize some of the low- level radioactive waste (LLRW) streams at the Chalk River Laboratories (CRL). The WTC at treats low- level radioactive liquid waste by removing the contaminants from the wastewater, concentrating them, and immobilizing them. The fundamental design concept for the WTC is to process the waste streams using forced circulation type liquid waste evaporation (LWE), to solidify the concentrates using thin film evaporator and to discharge the purified effluent into the Ottawa River following verification monitoring. The solidified product drums are stored in existing storage facilities in the CRL. The LWE was installed in the WTC to treat the LLRW. After about four (4) years of design, construction and cold commissioning, the active commissioning of the evaporator ...

2006-07-01

495

Costs for off-site disposal of nonhazardous oil field wastes: Salt caverns versus other disposal methods  

Energy Technology Data Exchange (ETDEWEB)

According to an American Petroleum Institute production waste survey reported on by P.G. Wakim in 1987 and 1988, the exploration and production segment of the US oil and gas industry generated more than 360 million barrels (bbl) of drilling wastes, more than 20 billion bbl of produced water, and nearly 12 million bbl of associated wastes in 1985. Current exploration and production activities are believed to be generating comparable quantities of these oil field wastes. Wakim estimates that 28% of drilling wastes, less than 2% of produced water, and 52% of associated wastes are disposed of in off-site commercial facilities. In recent years, interest in disposing of oil field wastes in solution-mined salt caverns has been growing. This report provides information on the availability of commercial disposal companies in oil-and gas-producing ...

1997-09-01

496

Basic design of alpha aqueous waste treatment process in NUCEF  

Energy Technology Data Exchange (ETDEWEB)

This paper described the basic design of Alpha Aqueous Waste Treatment Process in NUCEF. Since various experiments using the TRU (transuranium) elements are carried out in NUCEF, wastes containing TRU elements arise. The liquid wastes in NUCEF are categorized into three types. Decontamination and volume reduction of the liquid waste mainly of recovery water from acid recovery process which has lowest radioactive concentration is the most important task, because the arising rate of the waste is large. The major function of the Alpha Aqueous Waste Treatment Process is to decontaminate the radioactive concentration below the level which is allowed to discharge into sea. Prior the process design of this facility, the followings are evaluated:property and arising rate of the liquid waste, room space to install and licensing condition. Considering ...

1996-11-01