International Science & Technology Center (ISTC)

Methods of Decontamination, Utilization, and Deactivation of Liquid Radioactive Wastes

Energy Technology Data Exchange (ETDEWEB)

Energy storage can be a cost-effective component of hybrid remote power systems. Storage serves the special role of taking advantage of intermittent renewable power sources. Traditionally this role has been played by lead-acid batteries, which have high life-cycle costs and pose special disposal problems. Hydrogen or zinc-air storage technologies can reduce life-cycle costs and environmental impacts. Using projected data for advanced energy storage technologies, LLNL ran an optimization for a hypothetical Arctic community with a reasonable wind resource (average wind speed 8 m/s). These simulations showed the life-cycle annualized cost of the total energy system (electric plus space heating) might be reduced by nearly 40% simply by adding wind power to the diesel system. An additional 20 to 40% of the wind-diesel cost might be saved by adding hydrogen storage or zinc-air fuel cells to the system. Hydrogen produced by ...

Energy Technology Data Exchange (ETDEWEB)

This article describes the processes for the treatment of plastic waste: sampling, sorting, comminution. The requirements for the different processes for waste treatment (as recycling, utilization as raw material, energy recovery, combustion) are listed. (SR)

Energy Technology Data Exchange (ETDEWEB)

The 1977 version of the Simpson-Puls-Dutton model appears to be the most amenable with respect to utilizing known or readily estimated quantities. The Pardee-Paton model requires extensive calculations involving estimated quantities. Recent observations by Koike and Suzuki on vanadium support the general assumption that crack growth in hydride forming metals is determined by the rate of hydride formation, and their hydrogen atmosphere-displacive transformation model is of potential interest in explaining hydrogen embrittlement in ferrous alloys as well as hydride formers. The discontinuous nature of cracking due to hydrogen embrittlement appears to depend very strongly on localized stress intensities, thereby pointing to the role of microstructure in influencing crack initiation, fracture mode and crack path. The initiation of hydrogen induced failures over relatively short periods ...

International Nuclear Information System (INIS)

Water chemistry of nuclear power plants has played an important role in reduction of personnel doses, structural materials and fuel integrity assurance, and reduction of radioactive wastes production. Further contributions are requested for advanced utilization of the LWR, advanced fuels and aging management of plants. Since water chemistry has an effect on all structure and materials immersed and at the same time affected by them, the optimum control not sticking to specific issues and covering the whole plant is required for these requests. Taking account of roles and activities of the industry, governmental institutes and academia, road maps on research and development plans for water chemistry were compiled into identified eleven items with targets and counter measures taken, such as common basic technologies, dose reduction, SCC mitigation, fuel cans corrosion/hydrogen absorption mitigation, condition based maintenance ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Drastic changes in waste management procedures are expected from the German Municipal Waste Disposal Regulations which became effective on June 1, 1993. Waste disposal will be subject to certain restrictions which, e.g. demand that wastes must be pretreated and inerted before they are stored. These regulations favor thermal waste disposal methods such as the carbonization/combustion method which is planned for a commercial-scale plant in the city of Fuerth. (orig./BBR)

Energy Technology Data Exchange (ETDEWEB)

A method for the hydroconversion of coal by solvent treatment at elevated temperatures and pressure wherein an alcohol having an alpha -hydrogen atom, particularly a secondary alcohol such as isopropanol, is utilized as a hydrogen donor solvent. In a particular embodiment, a base capable of providing a catalytically effective amount of the corresponding alcoholate anion under the solvent treatment conditions is added to catalyze the alcohol-coal reaction.

International Nuclear Information System (INIS)

The feasibility of utilizing photoelectrochemical and electrolytical technologies to convert energy from the sun and wind into hydrogen was studied. In exploring opportunities to reduce the cost of hydrogen production through interaction with the electric utility grid, it was found that direct photoelectrochemical (PEC) conversion of sunlight has the economic potential to compete with direct photovoltaic/electrolysis, notwithstanding the significant stability and efficiency issues that are still awaiting solution. Interaction with the grid, while maximizing electrolizer use, makes a significant impact on the economics of producing hydrogen by photovoltaic/electrolysis, making wind-based systems also more economical. Electrolysis was found to be the optimal solution only with electricity from renewable sources or with less expensive non-peak electricity. On the other hand, the ...

Energy Technology Data Exchange (ETDEWEB)

The proceedings of a workship of researchers and potential users of decomposed method fuel for Otto cycle engines are presented. The purpose of the meeting was to review the state-of-the-art. Proponents for its use state that by using exhaust waste heat to decompose the methanol, the resulting gaseous fuel constituents have more energy content than that in the original liquid. The drawbacks include the unapplicability during engine warmup and the fraction of automobile duty cycle related thereto, the reduced volumetric efficiency associated with any gaseous fuel, and the tradeoffs between improved thermal efficiency and reduced power output with lean fuel mixtures. There has always been a dilemma as to whether a decomposed methanol system is a variation on the application of methanol, of hydrogen, or both. However, the more immediate issue is whether use of methanol is liquid, decomposed or dual form is the most cost effective and energy ...

Science.gov (United States)

... will utilize man-made habitats, including artificial wetlands, waste water ponds, water hazards on golf courses, and an abandoned ... ...

Energy Technology Data Exchange (ETDEWEB)

Role of microelements in coal in connection with their combustion in power stations, gasification and hydrogenation is discussed from the standpoint of environmental pollution and effects on technological parameters. In the wastes from fossil-fuel power stations there are biogenic and toxic elements (Be, B, Pb, etc.) present, which eventually go into the soil. Analyses showed that coal from the Kuznetsk, Donetsk, Ehkibastuz and Kansk-Achinsk basins which are used for power, have a relatively low level of biogenic and toxic microelements, e.g. Ba, B, Mn, Pb, Co, Ni, V, Cu, Y. Coal reactivity in gasification and hydrogenation is discussed. The catalytic effect of several microelements in coal gasification and hydrogenation is established. A geochemical multiplicative indicator is presented which makes quantitative evaluation of the suitability of coals for hydrogenation possible. 17 ...

Energy Technology Data Exchange (ETDEWEB)

The follow-up system for wastes (JAeSTI), developed at the end of the 1990s, forms a basis for today's followup activities in Finland. JAeSTI relies on an environmental protection database, the compliance monitoring system VAHTI operated by the environmental authorities. Waste followup and waste statistics depend very much on the annual waste quantities recorded in the VAHTI system. In the KYJ-project the coverage and reliability of the data in the VAHTI system was evaluated as for the streams of solid municipal waste. The project also included the compiling of national statistics on municipal waste for the year 2000. The project used other information sources, too, such as statistics compiled when the National Waste Plan and regional waste plans were revised in 2002. In addition, the extent and quantity of ...

Wastenet

such as public utilities, waste disposal sites, large energy dependent facilities including factories, institutions ( ...provides immediate identification of PCB wastes, informs company officials of any special handling or disposal techniques ...provides immediate identification of PCB wastes, informs company officials of any special handling or disposal techniques

Energy Technology Data Exchange (ETDEWEB)

The oxidation of sulfur dioxide in gas diffusion electrodes (GDE) in the presence of a homogeneous catalyst, potassium iodide, is investigated. The influence of this catalyst on the voltage-current (V-I) characteristics of the electrodes and the utilization of sulfur dioxide is determined. It is shown that when using the homogeneous catalyst potassium iodide, the utilization can reach 95-100%.

International Nuclear Information System (INIS)

The rates of hydrogen release from simulated high-level liquid waste (SHLLW) during irradiation of "6"0Co #gamma#-rays have been studied using a laboratory-scale apparatus. The SHLLW used was made up of 28 different metal elements, the concentrations of which were determined from a computed data (ORIGEN-2) for a Purex spent fuel (burn-up of 4.5 GWd/t, cooling time of 4 years) except for those of corrosion products (Fe, Cr and Ni) and of chemical process additive (P). The nitrate ion concentration of the SHLLW was 4.97 M. The G-value of hydrogen release was 0.0164 for stirred conditions, but for nonstirred conditions with dose rate : 2.8 kGy/h and with the SHLLW solution height more than 8 cm, the following relation was found between the G-value and the solution height (d cm); G(H_2) = 0.100 d"-"1"."6. The G-values of oxygen and nitrogen releases were also determined. (author).

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is to the application of a methodology to evaluate the energy associated to the industrial solid wastes in the metropolitan region of Campinas. The methodological route proposed is: the characterization of the research area and the production/management of the industrial solid wastes; the energetic classification and the qualitative/quantitative research of the energy associated to the industrial solid wastes; and, the valuation of the applicability of the energetic utilization mechanisms proposed to the region. This methodology when applied at the Campinas metropolitan region proved to be valid and it resulted in a synthetically presentation of the social and environmental reality of the industrial sector and the destination of the wastes, as well as it indicated the potentialities related to the energetic utilization of the industrial ...

Energy Technology Data Exchange (ETDEWEB)

Red mud has been activated by dissolution in hydrochloric acid and reprecipitation with ammonia. The activated material has been evaluated as a catalyst for the hydrogenation of naphthalene, phenanthrene and pyrene and in the hydroliquefaction of both a high and low rank coal utilizing solvents of high and low hydrogen donating ability. Activation led to a substantial increase in the ability to hydrogenate the model compounds and a significant increase in oil yield was obtained in the hydroliquefaction of a low rank coal in the presence of a poor donor solvent. However, activation did not lead to significant increases in overall yields of liquids in other cases and the activated red mud was significantly less active than a commercial nickel-molybdenum-sulphur catalyst. 27 refs., 1 fig., 5 tabs.

International Nuclear Information System (INIS)

A major objective of the DOE Advanced Fuel Cycle Initiative, AFCI, is to explore technologies that may reduce the long-term environmental burden of nuclear energy through more efficient disposal of waste materials. In this work, the potential impact of the AFCI technology and its beneficial effects on waste management and its ability to meet waste management objectives are demonstrated. In addition, practical scenarios to improve permanent disposal utilization and/or reduce the temporary spent nuclear fuel (SNF) storage inventory by closing the fuel cycle through transition to fast reactor (FR) converters are also discussed. (authors)

UK PubMed Central (United Kingdom)

Animal facilities generate a large amount of used bedding containing excrement as medical waste. We developed a recycling system for used bedding that involves soft hydrothermal processing. In this...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The set of activities performed by SENTECH, Inc. addressed the specific recommendations provided to the Department of Energy (DOE) by its advisors, including the Hydrogen Technical Advisory Panel and the review panel members of the DOE Annual Hydrogen Program Review. SENTECH`s efforts were conducted under five tasks: Task 1: Technology and Process Analysis; Task 2: Hydrogen Information Development and Transfer; Task 3: Educational Products; Task 4: Systems Analysis; and Task 5: Life Cycle Costs. SENTECH activities were executed in two broad areas--analysis and technology transfer. The analytical tasks undertaken in FY97 were focused on two types of analysis--systems analysis and technical/economic assessments. These analytical activities benefit DOE by providing data that allow it to define the strategic goals of the hydrogen R and D program. By collecting analysis of the energy efficiency, ...

Science.gov (United States)

This study examined the atmospheric pollution created by some waste treatment and disposal facilities in the State of Kuwait. Air monitoring was conducted in a municipal wastewater treatment plant, an industrial wastewater treatment plant established in a petroleum refinery, and at a landfill site used for disposal of solid wastes. Such plants were selected as models for waste treatment and disposal facilities in the Arabian Gulf region and elsewhere. Air measurements were made over a period of 6 months and included levels of gaseous emissions as well as concentrations of volatile organic compounds (VOCs). Samples of gas and bioaerosols were collected from ambient air surrounding the treatment facilities. The results obtained from this study have indicated the presence of VOCs and other gaseous pollutants such as methane, ammonia, and hydrogen sulphide in air surrounding the waste ...

International Nuclear Information System (INIS)

Probabilistic risk assessment is a technique used to systematically analyze complex technical systems, such as nuclear waste management facilities, in order to identify and measure their public health, environmental, and economic risks. Probabilistic techniques have been utilized at the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico, to evaluate the probability of a catastrophic waste hoist accident. A probability model was developed to represent the hoisting system, and fault trees were constructed to identify potential sequences of events that could result in a hoist accident. Quantification of the fault trees using statistics compiled by the Mine Safety and Health Administration (MSHA) indicated that the annual probability of a catastrophic hoist accident at WIPP is less than one in 60 million. This result allowed classification of a catastrophic hoist accident as ''not credible'' at ...

Energy Technology Data Exchange (ETDEWEB)

As waste disposal methods and long-term precautionary care of the environment are closely related, disposal of non-avoidable and intractable residual products is to be viewed primarily from a safety angle. Also, thermal processes airm mainly at treatment, not utilization. 'Safety' in this context addresses both the environmental compatibility of the products and the process itself. In other words, only mature techniques (i.e., safe, proven ones) are employed. (orig.)

Energy Technology Data Exchange (ETDEWEB)

PRESTO-II is a computer code developed to evaluate possible health effects from shallow land disposal of low level radioactive wastes. PRESTO-PREP is a data preprocessor that has been developed to expedite the formation of input data sets for PRESTO-II. PRESTO-PREP utilizes a library of nuclide and risk-specific data. Given an initial waste inventory, the code creates the radionuclide portion of the associated input data set for PRESTO-II. 2 references.

Energy Technology Data Exchange (ETDEWEB)

The Formerly Utilized Sites Remedial Action Program (FUSRAP) is to evaluate the radiological conditions at former MED-US AEC sites. Purpose of the Ocean FUSRAP program is to assess the feasibility of ocean disposal of FUSRAP waste which contains trace natural radioactive materials. This paper presents soil characterization information on the Middlesex, NJ, Sampling Plant site, and reports preliminary ocean dispersion calculations. (DLC)

Energy Technology Data Exchange (ETDEWEB)

This two-volume proceedings summarize the results of fifteen innovations that were funded through the US Department of Energy`s Innovative Concept Program. The fifteen innovations were presented at the sixth Innovative Concepts Fair, held in Austin, Texas, on April 22--23, 1993. The concepts in this year`s fair address innovations that can substantially reduce or use waste streams. Each paper describes the need for the proposed concept, the concept being proposed, and the concept`s economics and market potential, key experimental results, and future development needs. The papers are divided into two volumes: Volume 1 addresses innovations for industrial solid waste processing and municipal waste reduction/recycling, and Volume 2 addresses industrial liquid waste processing and industrial gaseous waste processing. Individual reports are indexed separately.

Energy Technology Data Exchange (ETDEWEB)

The wastes management policy takes into account more and more often the environmental impacts mastership. This evolution is particularly appreciable when the wastes directly interact with the environment: storage, utilization for roads construction and so on. In this context the ADEME organized the 8 june 2000 a colloquium to present the new evaluation methods and tools, to describe the regulations and to identify the research programs needed for this environmental policy. Eleven papers are presented. (A.L.B.)

Energy Technology Data Exchange (ETDEWEB)

This paper reported on a study in which hydrogen was produced by fermentation of biomass. A continuous process using a non-sterile substrate with a readily available mixed microflora was used on heat treated digested sewage sludge from a wastewater treatment plant. Hydrogen was produced from waste sugar at a pH of 5.2 and a temperature of 37 degrees C. An experimental setup of three 5.5 L working volume continuously stirred tank reactors (CSTR) in different stirring speeds were constructed and operated at 7 different hydraulic retention times (HRTs) and different organic loading rates (OLR). Dissolved organic carbon was examined. The results showed that the stirring speed of 135 rpm had a beneficial effect on hydrogen fermentation. The best performance was obtained in 135 rpm and 8 h of HRT. The amount of gas varied with different OLRs, but could be stabilized on a high level. Methane was not detected ...

Energy Technology Data Exchange (ETDEWEB)

Three samples of dusts generated by the non ferrous metallurgical industries are treated between 200 and 800 degree centigree in controlled oxidizing and reducing atmospheres. The objective of this study is to recover the valuable metals from these wastes. The treatments of these solids under oxidizing conditions at 700 degree centigree are well adapted for two samples. The totality of valuable elements are concentrated in the treatments residues. The use of hydrogen at 600 degree centigree, permits the removal of up to 100 % of valuable metals contained in the treated industrial wastes. The recovery rate of valuable metals (Pb, Zn, Cu) as well as the Global Decontamination Factor are reported. (Author) 9 refs.

Energy Technology Data Exchange (ETDEWEB)

It becomes a cause of the air pollution by the generation of hydrogen chloride, when it is incinerated, when it decays, even if the plastic which becomes spent is buried. Every year, it is abundantly discharged and accumulates. Countries and enterprises, etc. carry out the examination for non-polluting processing and resource recycling of the waste plastic for material recycling and development by methods such as thermal recycling, practical application. In this paper, the following are examined: Plastic output and transition of the situation of the disposal quantity, resource recycling and problem. It wants to explain the challenge of more and more efficient resource recycling. (NEDO)

Energy Technology Data Exchange (ETDEWEB)

The Safety Analysis Report for the TRUPACT-II Shipping Package [Transuranic Package Transporter-II (TRUPACT-II) SARP] set limits for gas generation rates, wattage limits, and flammable volatile organic compound (VOC) concentrations in transuranic (TRU) waste containers that would be shipped to the Waste Isolation Pilot Plant (WIPP). Based on existing headspace gas data for drums stored at the Idaho National Engineering Laboratory (INEL) and the Rocky Flats Environmental Technology Site (RFETS), over 30 percent of the contact-handled TRU waste drums contain flammable VOC concentrations greater than the limit. Additional requirements may be imposed for emplacement of waste in the WIPP facility. The conditional no-migration determination (NMD) for the test phase of the facility required that flame tests be performed if significant levels of flammable VOCs were present in TRU waste ...

International Nuclear Information System (INIS)

This final report for the Swiss Federal Office of Energy looks at the possibilities for improved waste water utilization in the Lavey-les-Bains thermal spa, Switzerland. According to the regulations in force, the temperature of the waste water rejected into the Rhone river shall not exceed 30 "oC, what is currently not the case. Also the operational cost shall be reduced and the waste water quality improved. The installations are presented. From the two geothermal wells, mineral water comes out at an average flow rate of 940 l/min and a temperature of 63 "oC. Actual waste water data are reported. The measured thermal water consumption data, including seasonal variations, are analysed by computerized simulation and measures to reduce the consumed volume by the optimization of internal procedures are evaluated. Measures to reduce the quantity of the rejected free chlorine are ...

Energy Technology Data Exchange (ETDEWEB)

The report presents selected highlights of how research has contributed to the regulatory effort. It explains the research role of the NRC and nuclear safety research contributions in the areas of: pressure vessel integrity, piping, small- and large-break loss-of-coolant accidents, hydrogen and containment, source term analysis, seismic hazards and high-level waste management. The report also provides a summary of current and future research directions in support of regulation.

Energy Technology Data Exchange (ETDEWEB)

This paper provides information on activities undertaken in a non- production oriented metal finishing operation to minimize waste and conserve resources. The facility is a 6000 sq foot shop that typically only deals with prototype parts. Utilizing a plan that includes employee awareness, common sense and existing technology, a noticeable reduction in waste volume has been obtained. Initiatives that are covered include: segregation of cyanide plating solutions, elimination of copper cyanide plating, elimination of hexavalent chromium plating, elimination of vapor degreasing, changing of rinsing practices, and changing a process for cleaning of aluminum parts. Some discussion is also presented on the effectiveness of combining the technologies of physical vapor deposition and electrodeposition to help minimize waste. Plans for additional initiatives including water recycling, elimination of cyanide ...

Energy Technology Data Exchange (ETDEWEB)

Catalytic activity of industrial metallic wastes in coal liquefaction was examined in a 100lb/day continuous coal processing development unit. Red mud, a waste material from the aluminium industry, and an electric furnace flue dust containing Ni, Mo, Co and Fe showed a pronounced effect on the conversion of a Kentucky bituminous coal. Coal conversion and oil production increased significantly with the addition of red mud and flue dust. Comparison of the catalytic activity of pyrite, red mud, and flue dust, based on selectivity analysis, showed that red mud was the most desirable disposable catalyst. However, if the primary goal of coal liquefaction is high oil production, irrespective of hydrogen consumption, pyrite is the most active catalyst among those discussed in the paper.

Energy Technology Data Exchange (ETDEWEB)

On-board reforming of liquid fuels to hydrogen for use in proton exchange membrane (PEM) fuel cell electric vehicles (FCEVs) has been the subject of numerous investigations. In many respects, liquid fuels represent a more attractive method of carrying hydrogen than compressed hydrogen itself, promising greater vehicle range, shorter refilling times, increased safety, and perhaps most importantly, utilization of the current fuel distribution infrastructure. The drawbacks of on-board reformers include their inherent complexity [for example a POX reactor includes: a fuel vaporizer, a reformer, water-gas shift reactors, a preferential oxidation (PROX) unit for CO cleanup, heat exchangers for thermal integration, sensors and controls, etc.], weight, and expense relative to compressed H{sub 2}, as well as degraded fuel cell performance due to the presence of inert gases and impurities in the reformate. ...

International Nuclear Information System (INIS)

Pilot-scale pyrolysis units have been in operation since 1980 to test the efficiency of thermal treatment of transuranic (TRU) solid waste to retrieve the TRUs and to reduce the volume of wastes such as spent solvent, spent resin, and others. These wastes are generated by reprocessing, fuel production, and utilities. NUKEM has developed a criticality-safe, ring-slab reactor to decompose solid TRU waste. The plant processes 25 kg/h with a polyvinyl chloride content up to 70%. The overall throughput (inactive) up to the spring of 1982 was 2000 kg. The decontamination factor for the reactor itself is 1000. The liquid wastes, mainly spent solvent, are cracked under nitrogen at 400 to 700"0C in a reactor that is filled by a packed bed kept in motion by a specially designed agitator. This unit was built for 15 kg/h water equivalent evaporation. Up to 1982 the unit ...

Energy Technology Data Exchange (ETDEWEB)

Limestone-based sorbents are used extensively in utility boilers and tail-gas desulfurization units to remove sulfur oxides formed during the combustion of fossil fuels. Such units generate {approximately}20 million tons of flue-gas desulfurization (FGD) wastes in the U.S. annually, the bulk of which ({approximately}95%) are discarded in landfills or holding ponds. However, a significant portion of the Ca in these materials is not sulfated (remains as CaO or Ca(OH){sub 2}), particularly in units that generate dry wastes. When hydrated, such wastes exhibit a strong affinity to absorb acid gases at ambient temperature. This study represents a continuation of previously reported CO{sub 2}-absorption studies and includes more recent work on the absorption of H{sub 2}S and NO. Ten FGD-waste samples along with a control fly ash were examined. Absorption capacities, the role of available ...

CERN Document Server

Radioactive Waste

Energy Technology Data Exchange (ETDEWEB)

The founding of the Hanford Engineering Works to produce plutonium is described. The 45-year defense mission has now been replaced with a peaceful mission, that of being the first site for massive cleanup of the 45-year nuclear waste. In order to establish a remedial investigation and feasibility plan, a process of discovery named the Technical Baseline Report must be performed; the task of this process is to discover all that is known about a proposed cleanup site (what the waste was, where did it go). When none of the documentation can answer the question, oral history is utilized. Some of the problems associated with the conduct of oral history interviews are described, particularly Hanford`s legacy of secrecy.

Science.gov (United States)

This report presents an overview of research activity currently being funded by the US Department of Energy (DOE) on solid wastes from coal gasification, coal liquefaction, and oil shale technologies, Projects conducted in the DOE energy technology centers and national laboratories, and in cooperative projects with other government agencies, private industry, and universities are developing the basic and applied technology and data on which present and future fuel-conversion and utilization processes depend. The report identifies data gaps and recommends research needs where warranted.

International Nuclear Information System (INIS)

The reduction of emission from power plants of the public power industry inevitably leads to more and more residual products being obtained which require utilization. Traditionally, the building and building materials industry as well as, for a number of years, the gypsum industry have been the main customers processing these residual materials. To avoid having to tip them at landfills that are in short supply already, further uses are sought; so, for instance, in farming to ameliorate soil and fertilize plants. Relative to this subject, proposals are already available which are presented as lectures at the conference and discussed, together with practical knowledge and new investigation results. (BBR).

Energy Technology Data Exchange (ETDEWEB)

The activities of Shell Hydrogen in the development of a hydrogen economy are outlined. Attention is paid to the use of hydrogen in electric cars and in homes, different types of fuel cells, and the catalytic partial oxidation (CPO) process of Shell to produce hydrogen

Science.gov (United States)

This topical report presents data and results obtained from the hydrogen microautoclave. The autoclave has been used to test for the quality of hydrotreater residue product and hydrotreater catalyst activity. Data obtained from Run 242 and the first part of Run 243 is presented in a convenient format and conclusions based upon this data are summarized. Some of the topics discussed in this report are the following: development and description of procedures for the catalyst and hydrotreater residue, the significance of test results and their meaning, and the relationship of test results to process performance. 7 references, 13 tables, 22 figures.

British Library Electronic Table of Contents (United Kingdom)

Abstract Melamine cyanurate (MCA) was utilized as an environmental friendly additive to prepare the nonhalogen flame retardant MCA/Nylon 66 composites by melt blending technique. Because of the strong hydrogen bond interactions and fine interfacial compatibility between MCA and Nylon 66, the resultant even dispersion of MCA filler in polymer matrix leads to the better toughness and strength of MCA/Nylon 66 composites than those of neat Nylon 66. Both Nylon 66 and MCA/Nylon 66 composites exhibit similar -crystalline structure, but the presence of MCA influences the distribution of 1 and 2 crystalline phases in Nylon 66 by inducing its hydrogen-bonded sheet separation. Moreover, the blending of MCA and Nylon 66 increases the crystallization temperature and exothermicity but decreases the the...

Energy Technology Data Exchange (ETDEWEB)

The waste tail gas fuel emitted from refinery plant in Taiwan e.g. catalytic reforming unit, catalytic cracking unit and residue desulfurization unit, was recovered and reused as a replacement fuel. In this study, it was slowly added to the fuel stream of a heater furnace to replace natural gas for powering a full-scale distillation process. The waste tail gas fuel contained on average 60 mol% of hydrogen. On-site experimental results show that both the flame length and orange-yellowish brightness decrease with increasing proportion of waste gas fuel in the original natural gas fuel. Moreover, the adiabatic flame temperature increases as the content of waste gas fuel is increased in the fuel mixture since waste gas fuel has a higher adiabatic flame temperature than that of natural gas. The complete replacement of natural gas by waste gas ...

Energy Technology Data Exchange (ETDEWEB)

Lawrence Livermore, Sandia Livermore and Los Alamos National Laboratories have a joint project to develop an optimized hydrogen fueled engine for series hybrid automobiles. The major divisions of responsibility are: system analysis, engine design and kinetics modeling by LLNL; performance and emission testing, and friction reduction by SNL; computational fluid mechanics and combustion modeling by LANL. This project is a component of the Department of Energy, Office of Utility Technology, National Hydrogen Program. We report here on the progress on system analysis and preliminary engine testing. We have done system studies of series hybrid automobiles that approach the PNGV design goal of 34 km/liter (80 mpg), for 384 km (240 mi) and 608 km (380 mi) ranges. Our results indicate that such a vehicle appears feasible using an optimized hydrogen engine. The impact of various on-board storage options on fuel ...

Energy Technology Data Exchange (ETDEWEB)

With an objective to know coal condensation structure which has influence on coal conversion reaction, an attempt was made on quantitative evaluation of hydrogen bonding in coal. Using as test samples the VDC made from Taiheiyo coal swollen by tetralin and vacuum-dried, and its pyrolyzed char, DSC measurement and Fourier transform infrared spectroscopy (FT) were performed. An FT spectrum comparison revealed that the VDC swollen at 220{degree}C has the hydrogen bonding relaxed partly from the original coal. However, since the change is in a huge coal molecular structure restraining space, it has stopped at relaxation of the bonding energy without causing separation as far as free radicals. On the other hand, the DSC curve shows that the VDC has slower endothermic velocity than the original coal. In other words, the difference in heat absorption amounts in both materials is equivalent to the difference of enthalpy ({Delta} H) of both materials, ...

Energy Technology Data Exchange (ETDEWEB)

Oestfold Research has trough the project 'Climate accounts for disposal' for Waste Norway developed a model for calculation of net greenhouse gas emissions at the disposal of various waste types. The model is based on life cycle methodology according to the standard IS014044. This model has been used for plastic packaging in the project by adapting the basic values of specific conditions in the municipality of Fredrikstad. Oestfold Research has made an assessment of greenhouse gas emissions for the recycling and material recovery of plastic packaging from households in the district on assignment from Fredrikstad municipality and compared with the current solution where plastic packaging together with residual waste is used for energy utilisation. Based on the population in Fredrikstad and estimated amount of plastic packaging waste arising per household per year the difference in ...

Energy Technology Data Exchange (ETDEWEB)

The methods introduced for the field of cleaning waste water can be classified under various processes. Chemical oxidation is done with ozone, hydrogen peroxide and ultraviolet irradiation with subsequent biological decomposition. Another method is ultra-filtration with recovery of valuable materials or waste water ponds with algae biomass to decompose ammonium compounds, nitrates and phosphates. (EF) [Deutsch] Die auf dem Gebiet der Abwasserreinigung vorgestellten Methoden kann man in verschiedene Verfahren einordnen. Die chemische Oxidation erfolgt mit Ozon, Wasserstoff-Peroxid, UV Bestrahlung und anschliessenden biologischen Abbau. Eine andere Methode ist die Ultrafiltration mit Rueckgewinnung von Wertstoffen oder Abwasserteiche mit Algenbiomasse zum Abbau von Ammoniumverbindungen, Nitraten und Phosphaten. (EF)

Science.gov (United States)

PMID:21763121

Energy Technology Data Exchange (ETDEWEB)

This article examines the developing market for independent power projects in Canada. The topics of the article include bidding in Ontario, the Quebec market, powering British Columbia, and market forces at work in Canada. Discussed are current projects in all stages of completion from bidding to production and includes gas-fired cogeneration, gas-fired combined-cycle electricity generation and cogeneration, wood-waste fired plants, repowering of existing utility plants, and hydroelectric power plants.

Energy Technology Data Exchange (ETDEWEB)

Objective was to develop a glass utilizing the silica waste material from geothermal energy production, and to supply local artists with this glass to make artistic objects. A glass composed of 93% indigenous Hawaiian materials was developed; 24 artists made 110 objects from this glass. A market was found for art objects made from this material.

Energy Technology Data Exchange (ETDEWEB)

An advanced process for the separation of hydrogen sulfide (H{sub 2}S) from coal gasification product streams through an electrochemical membrane is being developed. H{sub 2}S is removed from the syn-gas stream, split into hydrogen, which enriches the exiting syn-gas, and sulfur, which is condensed from an inert sweep gas stream. The process allows removal of H{sub 2}S without cooling the gas stream and with negligible pressure loss through the separator. The process is made economically attractive by the lack of need for a Claus process for sulfur recovery. Membrane manufacturing coupled with full-cell experimentation was the primary focus this quarter. A tape-casted zirconia membrane was developed and utilized in one full-cell experiment (run 25); run 24 utilized a fabricated membrane purchased from Zircar Corporation. Results are discussed.

Energy Technology Data Exchange (ETDEWEB)

The production of polarized negative ion beams by ''collisional pumping'' is described. Collisional pumping utilizes repeated charge changing collisions in a thick electron-spin-polarized gas or vapor target to form a polarized fast atom beam. The polarized fast atom beam is then partially converted into a polarized negative ion beam in a vapor target. Analysis is presented for a hydrogen beam passing through either a thick polarized H atom target or a thick polarized alkali target. Large polarizations and large currents may be possible.

Energy Technology Data Exchange (ETDEWEB)

Thermal neutron beam from the TNRF of JRR-3M was utilized for detection of mice lung cancer in vivo. Both the static and real-time neutron imaging were tried. Very strong thermal neutron beam is necessary to detect lung cancers because small changes are hidden by the very large attenuation of thermal neutron beam by the hydrogens in the tissues. The detection was successfully performed. Especially, the Super Eye of Hamamatsu Photonics contributed very effectively. Bone marrows and cartilages were also shown clearly. If an efficient and compact neutron source will become available in future, this method will grow up as a powerful tool for biomedical application. (author).

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

Energy Technology Data Exchange (ETDEWEB)

The Ministere des Ressources naturelles du Quebec (Quebec Natural Resources Department) implemented a remedial program to treat the waste rock pile at Wood Cadillac, located near Cadillac, in Abitibi, Quebec. The solutions proposed by INRS-Georessources and ENVIROCONSEIL are aimed at eliminating erosion and stabilizing the geochemical processes. Part of the proposed solution also included the use of a reducing trickling filter for the treatment of acid leachates, which also contain arsenic when exiting the waste rock pile. The trickling filter is composed of forest tailings in which the bacteria reduce the sulphates and stimulate the precipitation of arsenic into arsenic sulphates. This is a new treatment that was developed following laboratory experiments which demonstrated the feasibility of the process and quantified the parameters. A demonstration unit was constructed by ENVIROCONSEIL and installed at the Wood Cadillac ...

Energy Technology Data Exchange (ETDEWEB)

A pyrochemical process has been introduced and utilized so that the transmutation of spent PWR fuel in PEACER can produce mainly low and intermediate level waste for near surface disposal. Major radioactive nuclides from PEACER pyroprocessing are composed of TRU and LLFP. In this study, the requirement for the final waste from PEACER is evaluated based on the methodology for establishment of waste acceptance criteria. Also, sensitivity analysis for several input parameters is conducted in order to determine acceptable decontamination factor (DF) and LLFP removal efficiency and to find out input parameter that extremely have an effect on DF. As a result of the study, LLFP removal efficiency, especially Sr-90 and Tc-99, is proved to be a major nuclide which contributes to annual dose by human intrusion scenario rather than TRU DF. More than 98.5% of LLFP have to be removed to meet below dose constraint ...

Energy Technology Data Exchange (ETDEWEB)

Studies are made on coal in terms of its effective utilization, coal cleaning, fluidization and production of new fuel, and issues globally raised. Coal is abundant in reserves and high in supply stability and economic efficiency. However, it is much in CO2 emission per calorific value. To control as much CO2 emission as possible, effective utilization such as increasing of power generation efficiency has been proceeded with. In addition to ultra supercritical pressure and fluidized bed combustion, cited are coal gasification combined cycle power generation and high temperature type fuel cell. Coal has 5-20% ash and impurities like sulfur/nitrogen. Coal should be used clean by pollution abatement measures such as dust collecting, desulfurization and denitrification. Japan is at a world top level of these technologies. Coal is solid, and therefore, is more difficult to handle than liquid fuel. To use it easily, coal is liquefied into slurry such ...

Energy Technology Data Exchange (ETDEWEB)

Six safety initiatives have been identified for accelerating the resolution of waste tank safety issues and closure of unreviewed safety questions. Safety Initiative 5 is to reduce safety and environmental risk from tank leaks. Item d of Safety Initiative 5 is to complete corrosion studies of single-shell tanks to determine failure mechanisms and corrosion control options to minimize further degradation by June 1994. This report has been prepared to fulfill Safety Initiative 5, Item d. The corrosion mechanisms that apply to Hanford Site single-shell tanks are stress corrosion cracking, pitting/crevice corrosion, uniform corrosion, hydrogen embrittlement, and microbiologically influenced corrosion. The corrosion data relevant to the single-shell tanks dates back three decades, when results were obtained from in-situ corrosion coupons in a few single-shell tanks. Since that time there have been intertank transfers, evaporation, and chemical ...

CERN Document Server

The Principles of Radioactive Waste Management

Science.gov (United States)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

This bibliography contains citations concerning the recycling of scrap plastic produced in the injection-molding process. Plastic pellets made from scrap that are used in the injection-molding process are also discussed. Recycling equipment and automated recycling systems are described. Ways to utilize plastic scrap from used cars, packaging materials, and waste from polyurethane production are presented. (This updated bibliography contains 116 citations, 14 of which are new entries to the previous edition.)

Energy Technology Data Exchange (ETDEWEB)

A detailed study was undertaken to examine the potential of iron oxide present in red mud (a waste product from Bayer's alumina process) as a sorbent for SO/sub 2/ capture by dry process. The other constituents present in the red mud can bring about enhanced utilization of the active component provided they are almost completely inert. The practical use of the process has been explored and a few batchwise cyclic operations of SO/sub 2/ capture and regeneration have also been carried out. A kinetic model of the reaction has been proposed.

Energy Technology Data Exchange (ETDEWEB)

This bibliography contains citations concerning Federal and state laws and management programs for the protection and use of inland wetlands. Utilization of wetlands to control highway runoff and community waste water is discussed. Wetlands protection programs, restoration projects, resource planning, and wetlands identification methods are cited. References to coastal and salt-water wetlands are excluded from this bibliography. (This updated bibliography contains 219 citations, 37 of which are new entries to the previous edition.)

International Nuclear Information System (INIS)

Recycling of used battery for recovering lead done by either small household/small scale industries has been identified as a source of air pollution, especially by heavy metal (Pb). This condition give an adverse impact toward workers and societies. Technological aspect is one of the causal. The process apply an open system. Therefore, a lot of energy, as well as dust wasted to the air without prior treatment. For overcoming this condition, closed system by utilizing Cupola furnace will be offered as one of the alternatives clean technology application and to increase the recovering performance in order to set an effective and efficient result. (author)

Energy Technology Data Exchange (ETDEWEB)

This report describes the sampling and chemical analyses of smoke gas components for combustion performed in the SP Industry Calorimeter, where continuous measurements of oxygen, carbon dioxide and carbon monoxide are an integrated part of the Calorimeter system. On-line measurements of nitrogen oxides and total amounts of unburnt hydrocarbons were performed. Hydrogen cyanide, hydrogen chloride and ammonia in the smoke were sampled and absorbed in impinger bottles and subsequently analyzed using wet chemical techniques. An adsorbent sampling system was designed to allow the identification and quantitative analysis of individual organic compounds in the smoke. Gas chromatography was utilized with a mass spectrometric detector for the identification and a FID for quantification of the total amounts as well as individual components. A procedure for cleaning the smoke gas duct in between the combustion experiments was designed ...

Energy Technology Data Exchange (ETDEWEB)

One of the most densely populated urban regions in the world is the Sao Paulo Metropolitan region (SPMR) in the State of Sao Paulo, Brazil. Air pollution is a real problem, mainly caused by vehicle exhaust fumes. The air pollution abatement measures adopted in the SPMR, such as the addition of ethanol to gasoline, the use of cars running on pure alcohol, the restrictions in the circulation of vehicles and the utilization of electronic fuel injection and catalyst have had a positive effect on the environment. The 25,000 buses and approximately 400,000 trucks, all operating on diesel, have not been affected by these measures, and it is believed that SPMR is the ideal location for testing new vehicular pollution reduction technologies. A project to this effect was launched by the Ministry of Mines and Energy in conjunction with a host of other partners, and it involved the operation of a fuel cell bus using hydrogen produced by electrolysis. The ...

Science.gov (United States)

In the course of observing by means of Auger spectroscopy graphite gasification reactions catalyzed by metals, it has been found that in the presence of hydrogen, nickel appears to diffuse from the surface into the bulk of the graphite. When potassium is deposited on graphite, it is volatilized above 400/sup 0/C. Surprisingly the production of methane and carbon dioxide from the reaction of graphite and steam was catalyzed by potassium at as low a temperature as 250/sup 0/C. It has been shown that literature on the alkylation of benzene with synthesis gas is erroneous and that the products reported are due to Lewis acid catalyzed cracking of benzene. A novel cobalt mediated, reversible cleavage of a vinyl-hydrogen bond has been discovered. All products from the thermal decomposition of tetralin have been identified. The stereochemistry of cis-1, 2 dihydrotetralin was determined. In the utilization of the water gas shift ...

Energy Technology Data Exchange (ETDEWEB)

Biomass is one of the main natural resources in Sweden. The present low-CO{sub 2} emission characteristics of the Swedish electricity production system (hydro and nuclear) can be retained only by expansion of biofuel applications for energy purposes. Domestic Swedish biomass resources are vast and renewable, but not infinite. They must be utilized as efficiently as possible, in order to make sure that they meet the conditions for sustainability in the future. Application of efficient power generation cycles at low costs is essential for meeting this challenge. This applies also to municipal solid waste incineration with energy extraction, which should be preferred to its dumping in landfills. Hybrid dual-fuel combined cycle units are a simple and affordable way to increase the electric efficiency of biofuel energy utilization, without big investments, uncertainties or loss of reliability arising from complicated ...

International Nuclear Information System (INIS)

The present investigation is a case study of Lucknow, the main metropolis in Northern India, which succumbs to a major problem of municipal solid waste and its management. A qualitative investigation using strengths, weaknesses, opportunities and threats analysis (SWOT) has been successfully implemented through this community participation study. This qualitative investigation emphasizes the limited capabilities of the municipal corporation's resources to provide proper facilitation of the municipal solid waste management (MSWM) services without community participation in Lucknow city. The SWOT analysis was performed to formulate strategic action plans for MSWM in order to mobilize and utilize the community resources on the one hand and municipal corporation's resources on the other. It has allowed the introduction of a participatory approach for better collaboration between the community and municipal corporation in ...

Energy Technology Data Exchange (ETDEWEB)

Tightening environmental regulations and the signing of the Kyoto protocol have prompted electric utilities to consider co-firing biomass with coal to reduce the levels of CO{sub 2}, SO{sub 2} and NOx in stack emissions. This analysis examines the cost competitiveness of plantation produced woody biomass and waste wood with coal in electricity production. A case study of woody biomass production and co-firing in northern Indiana is presented. A linear programming model was developed to examine the optimal co-firing blend of coal and biomass while minimizing variable, cost, including the cost of ash disposal and material procurement costs. This model was used to examine situations where coal is the primary fuel and waste wood, willow trees, or both are available for fuel blending. The results indicate that co-firing woody biomass is cost-effective for the power plant. Sensitivity analysis explored the effect of ...

Energy Technology Data Exchange (ETDEWEB)

Thin passive layers of uranium nitride were formed by nitriding pure metallic uranium in non-equilibrium, low pressure radio-frequency plasma of nitrogen. Plasma nitriding at low substrate temperature of 230 C-250 C was found to cause the formation of adherent layers of uranium sesquinitride ({alpha}-U{sub 2}N{sub 3}) which provide a considerable protection against hydrogen attack. The characteristics of these passivation layers were determined by X-ray diffraction and Auger electron spectroscopy. The incipient hydriding kinetics of the plasma-treated samples were compared with those of untreated and nitrogen-ion implantation ones, utilizing a hot-stage microscope that was monitored continuously with a TV camera and videotape. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Brookhaven National Laboratory is involved in a conceptual design study of a commercial nuclear power system which utilizes high-temperature electrolysis to produce synthetic fuels. The system is called HYFIRE. It includes a tokamak fusion power reactor supplying electrical and thermal energy to an array of electrolytes. The electrolytes produce hydrogen which can be used either directly as a fuel or in the production of hydrocarbons. The purpose of the study is to provide a mechanism for DOE to further assess the commercial potential of fusion using a tokamak reactor to produce synthetic fuel. The HYFIRE design is based on the tokamak commercial power reactor, STARFIRE. STARFIRE uses the deuterium/tritium/lithium fuel cycle. The HYFIRE study assumes the plasma shape and characteristics of STARFIRE study but uses a different blanket design. This study is particularly interested in the possibility of using the STARFIRE tokamak in the production ...

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy Order 435.1, Radioactive Waste Management, requires a disposal authorization statement authorizing operation (or continued operation) for low-level waste disposal facilities. In fulfillment of these requirements, a disposal authorization statement was issued on October 25, 1999, authorizing the Hanford Site to transfer, receive, possess, and dispose of low-level radioactive waste at the 200 East Area burial grounds and the 200 West Area burial grounds. One of the conditions is that monitoring plans for the 200 East Area and 200 West Area low-level burial grounds be written and approved by the Richland Operations Office. As a result of a record of decision for the Hanford Site Solid Waste Program and acceptance of the Hanford Site Solid Waste Environmental Impact Statement, the use of the low-level burial ground (LLBG) as a disposal facility for ...

Energy Technology Data Exchange (ETDEWEB)

This document describes research performed at the Morgantown Energy Technology Center in the areas of oil and gas, advanced systems application, environmental technologies, applied energy science and remediation. The following subtasks are described: CROW{sup TM} Process Modeling, Development of a Portable Data Acquisition System and Coalbed Methane Simulator, Tank Bottom Waste Processing using the TaBoRR{sup TM} Process, Process Support and Development, Eastern Shale Oil Residue as an Asphalt Additive, Solid Waste Management, Remediation of Contaminated Soils, The Syn-Ag{sup TM} Process: Coal Combustion Ash Management Option, the Maxi-Acid{sup TM} Process: In- sit Amelioration of Acid Mine Drainage, Spill Test Facility Database, Heavy Oil/Plastics Co-Processing, Fossil Fuel and Hydrocarbon Conversion Using Hydrogen-Rich Plasmas, and North Site Remediation.

Energy Technology Data Exchange (ETDEWEB)

This was a university-based research project in support of distributed reforming production technologies for hydrogen. Our objective was to examine the steam reforming of bio-ethanol and other related bio-derived liquids over non-precious metal catalyst systems to enable small-scale distributed hydrogen production technologies from renewable sources. The study targeted development of a catalytic system that does not rely on precious metals and that can be active in the 350-550 C temperature range, with high selectivity and high stability. To this end, we adopted a multi-prong research strategy, that included catalyst formulation and synthesis, detailed catalyst characterization, reaction kinetics and reaction engineering, molecular modeling and economic analysis studies. Our approach was an iterative one, where the knowledge gained in one aspect of the study was utilized to modify and fine-tune catalyst development. The ...

Energy Technology Data Exchange (ETDEWEB)

A brief description of a method for producing relatively intense molecular negative ion beams for the difficult Group IIA elements is given which offers considerable improvement in terms of source operation and beam intensity stability over other methods conventionally utilized. It is particularly suited for use in cesium plasma sources such as the Aarhus geometry and axial geometry versions of the source. The method utilizes H/sub 2/ source feed gas for the production of a hydrogen-rich plasma discharge which sputters a negatively biased probe made of elemental or copper alloy material. Negative ion beams of MgH/sub 3//sup -/>=12 ..mu.. A have been realized during routine operation of the 25 MV tandem accelerator. Negative ion beam intensity data, typical source operational parameters, and examples of mass spectra associated with their production are given. Interesting intermetallic molecular negative ion beams ...

UK PubMed Central (United Kingdom)

Hydrogen peroxide is a commonly used oxidizing agent with a variety of uses depending on its concentration. Ingestion of hydrogen peroxide is not an uncommon source of poisoning, and results in morbidity...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper details the development of a decontamination approach for the West Valley Demonstration Project (WVDP), Decontamination Project Plan (Plan). The WVDP is operated by West Valley Nuclear Services Company (WVNSCO), a subsidiary of Westinghouse Government and Environmental Services, and its parent companies Washington Group International and British Nuclear Fuels Limited (BNFL). The WVDP is a waste management effort being conducted by the United States Department of Energy (DOE) at the site of the only commercial nuclear fuel reprocessing facility to have operated in the United States. This facility is part of the Western New York Nuclear Service Center (WNYNSC), which is owned by the New York State Energy Research and Development Authority (NYSERDA). As authorized by Congress in 1980 through the West Valley Demonstration Project Act (WVDP Act, Public Law 96-368), the DOE's primary mission at the WVDP is to solidify high-level liquid nuclear ...

Energy Technology Data Exchange (ETDEWEB)

Oxide catalysis plays a central role in hydrocarbon processing and improvements in catalytic activity or selectivity are of great technological importance because these improvements will translate directly into more efficient utilization of hydrocarbon supplies and lower energy consumption in separation processes. An understanding of the relationships between surface structure and catalytic properties is needed to describe and improve oxide catalysts. Our approach has been to prepare supported oxides that have a specific structure and oxidation state and then employ these structures in reaction studies. Our current research program is focused on studying the fundamental relationships between structure and reactivity for two important reactions that are present in many oxide-catalyzed processes, partial oxidation and carbon-carbon bond formation. Oxide catalysis can be a complex process with both metal cation and oxygen anions participating in the chemical ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

British Library Electronic Table of Contents (United Kingdom)

''Hybrid'' hydrogen storage, where hydrogen is stored in both the solid material and as a high pressure gas in the void volume of the tank can improve overall system efficiency by up to 50% compared to either compressed hydrogen or solid materials alone. Thermodynamically, high equilibrium hydrogen pressures in metal-hydrogen systems correspond to low enthalpies of hydrogen absorption-desorption. This decreases the calorimetric effects of the hydride formation-decomposition processes which can assist in achieving high rates of heat exchange during hydrogen loading-removing the bottleneck in achieving low charging times and improving overall hydrogen storage efficiency of large hydrogen stores. Two systems with hydrogenation enthalpies close to -20kJ/mol H2 were studied to ...

Energy Technology Data Exchange (ETDEWEB)

Co-combustion tests for recycled fuels and peat were made at a 15 kW fluidized bed reactor at VTT Energy in Jyvaeskylae. Peat was used as reference fuel. 25 tests in total were performed during 1994 - 1996. A part of the peat energy was substituted by coal in five tests, in order to change the sulphur/chlorine ratio of the fuel mixture. Fuel mixtures (25% recycled fuel and 75% peat, at energy ratio) were pelletized in order to get homogeneous fuel mixtures. The tests in the year 1994 were air staging experiments (with and without tertiary air). All test were performed with air staging in the years 1995 and 1996. The aim of the research was to determine whether the co-combustion of waste materials will cause additional emission problems, as compared to combustible emissions from conventional air-staged fluidized bed combustion. Further, the aim was to study which large-volume components can be burned safely. One aim was to study the influence of fuel properties and ...

Energy Technology Data Exchange (ETDEWEB)

In this report, we have examined some of the fundamental mechanisms expected to be at work during mobilization of the waste within the double-shell tanks at Hanford. The motivation stems from the idea that in order to properly apply correlations derived from scaled tests, one would have to ensure that appropriate scaling laws are utilized. Further, in the process of delineating the controlling mechanisms during mobilization, the currently used computational codes are being validated and strengthened based on these findings. Experiments were performed at 1/50-scale, different from what had been performed in the previous fiscal years (i.e., 1/12- and 1/25-scale). It was anticipated that if the current empirical correlations are to work, they should be scale invariant. The current results showed that linear scaling between the 1/25-scale and 1/50-scale correlations do not work well. Several mechanisms were examined in the scaled tests which might ...

Energy Technology Data Exchange (ETDEWEB)

JRR-3 is a research reactor of 10 MWt output, which attained the criticality in 1962. All the design, manufacture, installation and others of this reactor were carried out by Japanese technologies, except the fuel and heavy water as the moderator and coolant, therefore it is nicknamed Home-made No.1 Reactor. Recently, due to the change in the state of utilizing research reactors and the rise of quality in the utilization, JRR-3 has become to be unable to meet sufficiently the needs of users. The plan of reconstructing the JRR-3 was considered under such situation, and in order to reuse the reactor building, the reactor proper is removed, and an entirely new, high performance, versatile reactor is to be constructed. In this paper, as to the removal works of the JRR-3 reactor proper, the method of execution, design, the execution of works and so on are outlined. The removal works of the reactor facilities were started in February, 1986. The ...

Energy Technology Data Exchange (ETDEWEB)

Renewable energy sources have been attracting the attention of a sensitized public since general pollution abatement measures have been taken, since efforts have been going into the protection of the earth atmosphere, the preservation of the vital ozone layer, and the conservation of fossil energy sources, and since nuclear power risks have been recognized and discussed. In addition to wind power and solar energy solid biomass, e.g. wood, wood wastes, vegetable residues and plants cultivated for the purpose of energy production, is among the topical alternatives. Agriculture and silviculture are important end-users of potential decentralized energy supplies and are cut out for supplying biomass for energy utilization. Additional income sources will open up for farmers. Based on these facts this KTBL working paper describes the biomass energy potential and feasible harvesting and solid-fuel processing and combustion techniques. Energy cost ...

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of ...

Science.gov (United States)

This report has been prepared in conjunction with an environmental baseline study for a commercial coal conversion facility being conducted by Ashland Synthetic Fuels, Inc. (ASFI) and Airco Energy Company (AECO). This report represents a cultural resource assessment for the proposed plant site and two potential solid waste disposal areas. This assessment presents data collected by Dames and Moore during a recent archaeological reconnaissance of the unsurveyed southeastern portion of the proposed plant site and two potential solid waste disposal areas. Also, results of two previous surveys on the northern and southwestern portion of the plant site for American Smelting and Refining Company (ASARCO) and Kentucky Utilities are included. The Dames and Moore survey of the southeastern portion of the plant site identified one archaeological site, three standing structures and one historic cemetery. In addition 47 archaeological ...

Energy Technology Data Exchange (ETDEWEB)

Babcock and Wilcox Volund is a major European provider of energy producing plants based on biomass and waste materials, which was founded in 1898 and today employs about 400 persons with headquarters and manufacturing in Esbjerg, Denmark. The R and D staff is about 10 persons, concentrating on gasification and improvement of traditional products. The Company turnover is about 120 mio. Euro annually, of which about 80 % is exported (50 % outside Europe - mostly far East). In 2000 the Company was acquired by US Company Babcock and Wilcox. In 1988 Volund initiated the development of updraft wood-chips gasifier Technology, which led to the commissioning of the Harboore gasifier early 1994. The work was supported in part by the Danish ELKRAFT Power Utilities and the Danish Energy Agency. The development process was carried out until 2002 and Volund now just concluded a license agreement with the Japanese engineering Company JFE. The overall layout ...

Energy Technology Data Exchange (ETDEWEB)

This paper reports on current dual fuel engines utilizing standard mechanical (Bosch type) fuel injection systems set to 5--6 percent pilot delivery that do not appear capable of reducing NO{sub x} emissions much below the current minimum of 4 g/bhp-h without incurring substantial penalties in efficiency and operability. A prototype Electronic Pilot Fuel Injector (EPFI) was designed that overcomes the shortcomings of the mechanical injection system, consistently delivering 3 percent or less pilot at pressures as high as 20,000 psi. The EPFI was installed and tested in one cylinder of a standard production dual fuel engine operating at a waste water treatment facility.

CERN Document Server

The goal of this work is to minimize the energy dissipation of embedded controllers without jeopardizing the quality of control (QoC). Taking advantage of the dynamic voltage scaling (DVS) technology, this paper develops a performance-aware power management scheme for embedded controllers with processors that allow multiple voltage levels. The periods of control tasks are adapted online with respect to the current QoC, thus facilitating additional energy reduction over standard DVS. To avoid the waste of CPU resources as a result of the discrete voltage levels, a resource reclaiming mechanism is employed to maximize the CPU utilization and also to improve the QoC. Simulations are conducted to evaluate the performance of the proposed scheme. Compared with the optimal standard DVS scheme, the proposed scheme is shown to be able to save remarkably more energy while maintaining comparable QoC.

International Nuclear Information System (INIS)

Thermoacoustics deals with the conversion of heat energy into sound energy and vice versa. It is a new and emerging technology which has a strong potential towards the development of sustainable and renewable energy systems by utilizing waste heat or solar energy. Although simple to fabricate, the designing of thermoacoustic devices is very challenging. In the present study, a comprehensive design and optimization algorithm is developed for designing thermoacoustic devices. The unique feature of the present algorithm is its ability to design thermoacoustically-driven thermoacoustic refrigerators that can serve as sustainable refrigeration systems. In addition, new features based on the energy balance are also included to design individual thermoacoustic engines and acoustically-driven thermoacoustic refrigerators. As a case study, a thermoacoustically-driven thermoacoustic refrigerator has been designed and optimized based on the developed ...

Science.gov (United States)

The report gives background design data for a specific copper smelter. The data is sufficiently detailed to allow air pollution control system engineering studies to be conducted. These studies will be concerned primarily with lean SO/sub 2/ streams that currently are not being captured. Physical layout of the smelter and the surrounding area is presented, along with existing control equipment. Ductwork that would be considered for future system tie-in is defined. Emissions from operating equipment, gas flow rates, temperatures, sulfur balance, and a process flow sheet are included. Utilities, stack dimensions, footing requirements, and solid waste handling are defined. Available area for new control equipment, gas characteristic variation, and potential new control equipment installation problems are discussed. (GRA)

Energy Technology Data Exchange (ETDEWEB)

The integrated-gasification combined-cycle (IGCC) process is an emerging technology that utilizes coal for power generation and production of chemical feedstocks. However, the process generates large amounts of solid waste, consisting of vitrified ash (slag) and some unconverted carbon. In previous projects, Praxis investigated the utilization of {open_quotes}as-generated{close_quotes} slags for a wide variety of applications in road construction, cement and concrete production, agricultural applications, and as a landfill material. From these studies, we found that it would be extremely difficult for {open_quotes}as-generated{close_quotes} slag to find large-scale acceptance in the marketplace even at no cost because the materials it could replace were abundantly available at very low cost. It was further determined that the unconverted carbon, or char, in the slag is detrimental to its utilization as ...

International Nuclear Information System (INIS)

The excess of US electrical generating capacity which has existed for the past 15 years is coming to an end as we enter the 1990s. Environmental and energy security issues associated with fossil fuels are kindling renewed interest in the nuclear option. The importance of these issues are underscored by the National Energy Strategy (NES) which calls for actions which open-quotes are designed to ensure that the nuclear power option is available to utilities.close quotes Utilities, utility associations, and nuclear suppliers, under the leadership of the Nuclear Power Oversight Committee (NPOC), have jointly developed a 14-point strategic plan aimed at establishing a predictable regulatory environment, standardized and pre-licensed Advanced Light Water Reactor (ALWR) nuclear plants, resolving the long-term waste management issue, and other open-quotes enabling conditions.close quotes GE is participating in ...

Energy Technology Data Exchange (ETDEWEB)

On account of a raised appearing of plastic waste and shreddered light fraction (SLF) from old car utilization as well as legal handicaps experiments were carried out at the Institute of Ferrous Metallurgy (RWTH Aachen) on a laboratory rig to inject DSD (Duales System Deutschland)-plastic waste and SLF with the destination of a subsequent raw material utilization in the blast furnace and cupola furnace. The experiments on the laboratory rig with DSD plastics could verify that by injection of specific coal/plastic mixtures into the blast furnace the injection rate could be raised by an improvement in the conversion degree and therefore the amount of the inserted reducing agent can be lowered. The injection of SLF without reduction of the inert materials and of the contents on alloying elements and/or tramp elements by extensive preparation has no advantages according to the experiments for the blast ...

Science.gov (United States)

... Other Sources Toxics Intranet Subsurface Injection of Liquid Waste -- Florida Surface features of a typical...

CERN Document Server

Radiation protection and the management of radioactive waste in the oil and gas industry

Science.gov (United States)

... wood, kitchen wastes, and human faeces. The ash from such waste burning shall be deposited and ...

Science.gov (United States)

... wood, kitchen wastes, and human faeces with the ash from such burning deposited and retained in an ...

International Science & Technology Center (ISTC)

Development, Investigation and Improvement of a System of Incinerating Crop Production Wastes in Small Capacity Boilers

Energy Technology Data Exchange (ETDEWEB)

The ''biotechnology 2000'' project is supervised by the project sponsor ''biology, energy, ecology'' at Forschungszentrum Juelich on behalf of the Federal Ministry for Research and Technology. The project activities cover the development of techniques and methods, cell biology, gene structure and gene regulation, photosynthetic production processes, biological hydrogen production, synthetic biology, protein design, neurobiological research, biosystems, plant breeding, phytomedicine and plant protection, the biology of waste disposal methods, research into methods which replace animal experiments, biological safety research, technology risk assessment, and ethical aspects. A general survey introduces the promoted projects, and standardized data sheets briefly introduce the individual activities. The appendix gives the project indices, the indices of joint projects, a list of ...

International Nuclear Information System (INIS)

Red mud is a waste and tail material from primary aluminum production, and is named for its color, coming from its iron oxide content. The quantity of red mud is almost equal to the primary aluminum production and leads to a considerable environmental issue. Red mud of the ETI Seydisehir Aluminum Plant is considered as detrimental waste for storage due to its content of various metal oxides, elements and caustics. This detrimental effect is classified into two groups: first, environmental health and second, the cost of storage. In order to minimize the negative effect of red mud, there have been or are presently many investigations carried out on usage of red mud in building materials. However, no effective way of utilizing red mud has yet been found. In this study domestic red mud was investigated and chemical analyses were performed by EDAX and XRF techniques. Radioactivity of the samples was also measured with gamma ...

Energy Technology Data Exchange (ETDEWEB)

The recent attempt to degassify a self contained liquid filled (SCLF) cable in Ontario Hydro is described. In September 1989, there was a high pressure alarm on one phase of a SCLF 115 kV cable circuit. The direct buried cable circuit is about 1,890 m long with two joints and was installed in 1968. Oil samples from the cable had 10 to 12% gas content with high levels of hydrogen, methane, and ethane, and very low levels of carbon monoxide, carbon dioxide, and acetylene. From these results it was concluded that the gas was generated by low energy electrical discharges and the paper insulation was not degraded. Various utilities and cable manufacturers were contacted to find if they had experienced similar problems. The cable duct oil was flushed and gasified and the successive oil samples were analyzed in order to locate the gassing site. The joints were examined and oil samples were taken through holes drilled in the cable sheath. From the test ...

Energy Technology Data Exchange (ETDEWEB)

Pd-Si metallic glasses have been utilized as catalysts in the Fischer-Tropsch reaction. The glasses are selective of ethane, whereas the in-situ crystallized glasses select a range of hydrocarbons characteristic of conventional Pd catalysts. This shift in selectivity has been observed in other hydrogenation reactions. Surface crystallization caused by the reaction conditions causes variable selectivity. Crystallization in reaction conditions has been monitored by DSC. During the course of the grant we developed the use of (+)- apopinene (6,6-dimethyl-1R,5R-bicyclo(3.1.1)hept-2-ene) as a molecular probe for determining the number and kinds of active sites on metallic glass catalysts. To accomplish this we conducted many experiments for comparison on other types of catalysts. These were foils, powders, and highly dispersed metals on several different supports. The glassy surfaces appear to be three dimensionally random (hilly or rolling) with ...

Energy Technology Data Exchange (ETDEWEB)

A lightweight, low permeability liner for graphite epoxy composite compressed gas storage vessels. The liner is composed of polymers that may or may not be coated with a thin layer of a low permeability material, such as silver, gold, or aluminum, deposited on a thin polymeric layer or substrate which is formed into a closed bladder using torispherical or near torispherical end caps, with or without bosses therein, about which a high strength to weight material, such as graphite epoxy composite shell, is formed to withstand the storage pressure forces. The polymeric substrate may be laminated on one or both sides with additional layers of polymeric film. The liner may be formed to a desired configuration using a dissolvable mandrel or by inflation techniques and the edges of the film seamed by heat sealing. The liner may be utilized in most any type of gas storage system, and is particularly applicable for hydrogen, gas mixtures, and oxygen ...

CERN Document Server

Aims: The production of saturated organic molecules in hot cores and corinos is not well understood. The standard approach is to assume that, as temperatures heat up during star formation, methanol and other species evaporate from grain surfaces and undergo a warm gas-phase chemistry at 100 K or greater to produce species such as methyl formate, dimethyl ether, and others. But a series of laboratory results shows that protonated ions, typical precursors to final products in ion-molecule schemes, tend to fragment upon dissociative recombination with electrons rather than just ejecting a hydrogen atom. Moreover, the specific proposed reaction to produce protonated methyl formate is now known not to occur at all. Methods: We utilize a gas-grain chemical network to probe the chemistry of the relatively ignored stage of hot core evolution during which the protostar switches on and the temperature of the surrounding gas and dust rises from 10 K to ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this research is to develop a technically and economically feasible process for biologically producing H(sub 2) from synthesis gas while, at the same time, removing harmful sulfur gas compounds. Six major tasks are being studied: 1. Culture development, where the best cultures are selected and conditions optimized for simultaneous hydrogen production and sulfur gas removal; 2. Mass transfer and kinetic studies in which equations necessary for process design are developed; 3. Bioreactor design studies, where the cultures chosen in Task 1 are utilized in continuous reaction vessels to demonstrate process feasibility and define operating conditions; 4. Evaluation of biological synthetic gas conversion under limiting conditions in preparation for industrial demonstration studies; 5. Process scale-up where laboratory data are scaled to larger-size units in preparation for process demonstration in a pilot-scale unit; and 6. Economic ...

Energy Technology Data Exchange (ETDEWEB)

A concept is shown for a fully reusable, Earth-to-orbit launch vehicle with horizontal takeoff and landing, employing an air-turborocket for low speed and a rocket for high-speed acceleration, both using liquid hydrogen for fuel. The turborocket employs a modified liquid air cycle to supply the oxidizer. The rocket uses 90% pure liquid oxygen as its oxidizer that is collected from the atmosphere, separated, and stored during operation of the turborocket from about Mach 2 to 5 or 6. The takeoff weight and the thrust required at takeoff are markedly reduced by collecting the rocket oxidizer in-flight. This article shows an approach and the corresponding technology needs for using air liquefaction and enrichment system propulsion in a single-stage-to-orbit (SSTO) vehicle. Reducing the trajectory altitude at the end of collection reduces the wing area and increases payload. The use of state-of-the-art materials, such as graphite polyimide, in a direct substitution for ...

International Nuclear Information System (INIS)

Hydrogen uptake and embrittlement of tantalum by electrolytically produced hydrogen is investigated on samples of varying composition and type of pretreatment. Of decisive influence on the uptake of hydrogen are the oxide layers present on the tantalum surface. By contact with platinum group metals as alloying constituents, surface coatings or anodic protection, a protection of tantalum can be obtained depending on the experimental conditions. (orig.).

Energy Technology Data Exchange (ETDEWEB)

This volume contains 5 appendices. Title listing are: technologies for recovery of transuranics; nondestructive assay of TRU contaminated wastes; miscellaneous waste characteristics; acceptance criteria for TRU waste; and TRU waste treatment technologies.

Wastenet

1 to the operator of a waste collective system by an agreement or contract. The conditions for the ...Fees of the waste collective system are subject to the supervision of the authority responsible for market surveillance. ...The operator of waste collection system collects wastes from producers and holder and transports these to a collection

Energy Technology Data Exchange (ETDEWEB)

Power source requirements for the military were presented to provide guidelines for research and development planning. Power sources that contain a high amount of energy and are small, light and durable are a common request from military users. Safety, reliability and low temperature performance are also important factors in the selection of power sources, as are cost and energy efficiency. Issues concerning advanced batteries were reviewed with reference to high energy density cathode materials. Various thermoelectric and renewable energy materials were discussed, with reference to recovery and conversion of waste heat. It was suggested that photovoltaic devices could help revolutionize military logistics by modifying energy re-supply requirements. Solid Oxide Fuel Cells (SOFC) were considered in relation to the high price of the ceramic materials required for operation. It was noted that the development of SOFC anodes capable of generating ...

Energy Technology Data Exchange (ETDEWEB)

This report presents the work performed at the Institute of Gas Technology (IGT) during the second program quarter from October 1, 1993 to December 31, 1993, under Department of Energy (DOE) Contract No. DE-AC22-93PC92114. This program has co-ordinated funding for Task 1 from IGT`s Sustaining Membership Program (SMP), while DOE is funding Tasks 2--8. Progress in all tasks are reported. The overall objective of this research project is to develop a catalytic process to convert natural gas to liquid transportation fuels. The process consists of two steps that each utilize catalysts and sulfur containing intermediates: (1) to convert natural gas to CS{sub 2} and (2) to convert CS{sub 2} to gasoline range liquids. Experimental data will be generated to demonstrate the potential of catalysts and the overall process. During this quarter, progress in the following areas has been made. An existing unit at IGT was modified to accommodate the sulfur feedstocks and the higher ...

Science.gov (United States)

The utilization of wood-shaving bottom ash (WBA) for the removal of Red Reactive 141 (RR141), an azo reactive dye, was investigated. WBA/H(2)O and WBA/H(2)SO(4) were made by treating WBA with water and 0.1M H(2)SO(4), respectively, to increase adsorption capacity. Adsorption of RR141 from reactive dye solution (RDS) and reactive dye wastewater (RDW) by WBA/H(2)O and WBA/H(2)SO(4) involved the BET surface area and pore size diameter. Properties of adsorbents, effect of contact time, initial pH of solution, dissolved metals and elution studies indicated that the decolorisation mechanism involved both chemical adsorption and precipitation with calcium ions. In addition, the WBA/H(2)SO(4) surface might contain sulphate-cation complexes that were specific to enhancing dye adsorption from RDW. The adsorption isotherm had a best fit by the Freundlich model. Freundlich parameters showed that WBA/H(2)O used more heterogeneous surface than WBA/H(2)SO(4) and activated carbon ...

UK PubMed Central (United Kingdom)

A synthetic strategy for constructing ionic hydrogen-bonded materials by combining perhalometallate anions with cations able to serve as hydrogen bond donors is presented. The approach is based on identification...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Researches and production of radio-isotopes, radio-pharmaceuticals and cold kits are carried out in the Radio-isotope Production Facility (RIPF). Four concrete hot cells in Bank-1 are to produce the Ir-192 source for NDT. Eleven lead hot cells in Bank-2 are to produce Ho-166, Cr-51, P-32/33, Tc-99m, Lu-177, Sr-90/Y-90 and W-188/Re-188 for research purpose. Six lead hot cells in Bank-3 are used for the production of I-131 for diagnosis and therapy of cancer in the hospital. A hot cell in Bank-3 is also utilized for the research of I-125 and Br-82. Four lead hot cells in Bank-4 are utilized for the production of Mo-99/Tc-99m generators since 2005. The major systems including the Heat and Ventilated Air Conditioning (HVAC) system and the air cleaning system such as charcoal and HEPA filter trains to filter the radioactive contaminants are in operation. So are the systems such as power supply and distribution system, UPS, fire protection system, ...

Energy Technology Data Exchange (ETDEWEB)

The feasibility study was conducted on a model project in Vietnam, aimed at solving the environmental pollution problems resulting from use of coal by demonstrating and disseminating the Japan's environmental technologies in the Southeast Asian countries. The feasibility study was conducted for the Cua Ong Coal Preparation Enterprise, which has the largest coal preparation capacity in Vietnam and port facilities. It is treating raw coal from 10 coal mines for classification and preparation, and shipping coal of various types that meet the standards for domestic use and export. The survey results point out that unrecovered coal remains in waste water discharged from the coal preparation plants to pollute the sea area, and that quantity of the refuse increases because of the unrecovered coal it contains. The environmental technologies needed to introduce include modification to variable wave pattern type jigging separator, refuse height measuring instrument ...

Energy Technology Data Exchange (ETDEWEB)

The chemical fixation of tritium in stearic acid followed by embedding the tritiated stearic acid into an epoxy resin proved to be a good method for permanent waste disposal of tritium gas. Tc-126 and Tc-136 hardener were used for this purpose. The polymerization temperature of the polymer products was found to be highly decreased by adding stearic acid and slightly decreased by adding stearic acid or by raising the temperature of the leachant medium and slightly decreased by irradiation. On the other hand, small improvement in the compressive strength of the polymer products was achieved by adding silica powder. The polymer product showed high flame points above 573 K although it contains stearic acid. DTA and TG analysis indicate that the thermal stability of polymer products containing stearic acid and silica powder is better than samples containing only stearic acid. Stearic acid was found to possess good resistance to irradiation and the amount of ...

UK PubMed Central (United Kingdom)

Woolfolk, C. A. (University of Washington, Seattle). Reduction of inorganic compounds with molecular hydrogen by Micrococcus lactilyticus. II. Stoichiometry with inorganic...Full Text Available

International Nuclear Information System (INIS)

Japanese Sep 2009 p. 103-106 Japan Idota, Yasuhiro Inoue, Hiroyuki

Energy Technology Data Exchange (ETDEWEB)

The assets that Citizen Potawatomi Nation holds were evaluated to help define the strengths and weaknesses to be used in pursuing economic prosperity. With this baseline assessment, a Planning Team will create a vision for the tribe to integrate into long-term energy and business strategies. Identification of energy efficiency devices, systems and technologies was made, and an estimation of cost benefits of the more promising ideas is submitted for possible inclusion into the final energy plan. Multiple energy resources and sources were identified and their attributes were assessed to determine the appropriateness of each. Methods of saving energy were evaluated and reported on and potential revenue-generating sources that specifically fit the tribe were identified and reported. A primary goal is to create long-term energy strategies to explore development of tribal utility options and analyze renewable energy and energy efficiency options. Associated goals are to ...

Energy Technology Data Exchange (ETDEWEB)

The paper deals with the disposal of radioactive waste and the plans for dealing with solid wastes of intermediate and low levels of activity, which are the responsibility of NIREX. NIREX is an executive body which co-ordinates the waste-disposal plans of the main radioactive waste producers. The disposal routes for the active wastes are described including the deep disposal of wastes containing material that will remain active for thousands of years. Requirements for deep burial are outlined with reference to the geology and hydrogeology of the site. Monitoring, maintenance and surveillance are mentioned for the protection of the public.

Energy Technology Data Exchange (ETDEWEB)

This document is a collection of spreadsheets detailing in a county by county manner the agricultural crop, agricultural wastes, municipal wastes and industrial wastes in Florida that are potential biomass energy sources.

Wastenet

Waste Technology and Innovation Study Final Report ...Waste Technology and Innovation Study Final Report 21/18569/150554 ...Survey of waste and resource recovery related technology and innovation, including products and product uses

Energy Technology Data Exchange (ETDEWEB)

The Si-L X-ray emission spectrum of amorphous hydrogenated silicon (a-Si:H) is presented and discussed. For a qualitative interpretation of the measured spectra cluster calculations of pure Si clusters (SiSi4) and Si clusters with hydrogen (SiSi3H) have been performed using a simplified LCAO-X scheme. In general the level shifts caused by introduction of hydrogen are small compared with the valence band width.

Science.gov (United States)

The evolution of massive stars through hydrogen and helium burning is addressed. A set of stellar

International Nuclear Information System (INIS)

The relationships of hydrogen alloyed #beta#-titanium alloy deformation behaviour to its microstructure and texture are investigated. It is shown that plasticity increases and strain induced texture changes at low hydrogen contents (0.1-0.2 mass %). Possible mechanisms responsible for specific features of #beta#-Ti alloy deformation are discussed. The study is made using alloy VT35 doped with hydrogen

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

This revision of the APT Waste Management Plan details the waste management requirements and issues specific to the APT plant for design considerations, construction, and operation. The APT Waste Management Plan is by its nature a living document and will be reviewed at least annually and revised as required.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

UK PubMed Central (United Kingdom)

Electronic waste or e-waste is one of the rapidly growing problems of the world. E-waste comprises of a multitude of components, some containing toxic substances that can have an adverse impact on human...Full Text Available

Science.gov (United States)

PMID:21769853

Science.gov (United States)

...2009-07-01 false Definition of solid waste. 261.2 Section 261.2 Protection...PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) IDENTIFICATION AND LISTING OF HAZARDOUS WASTE General § 261.2 Definition...

International Nuclear Information System (INIS)

The effect of various hydrogen concentrations on the crystal lattice period and the hardness of titanium alloy was examined, the alloy containing about 16 at.% Mo (27.5 wt. % Mo) and having #beta# structure. The peculiar features of the mechanism of plastic deformation of the alloy were studied after adding hydrogen to it. A dependence of the crystal lattice period on the concentration of hydrogen was obtained for TixMoxH_2 alloy. It has been established that the hardness of the Ti-Mo alloy does not change when hydrogen is added to it. The presence of hydrogen introduces changes into the mechanism of deformation of #beta#-titanium alloy. The configuration of the inverse pole figures after rolling proves that the transverse slip process in an alloy with hydrogen is hampered, and that the coplanar slip process is developing in it.

Science.gov (United States)

Lunar resource utilization has focused principally on the extraction of oxygen from the lunar regolith. A number of schemes have been proposed for oxygen extraction from Ilmenite and Anorthite. Serendipitously, these schemes have as their by-products (or more directly as their "waste products"), materials needed for the fabrication of thin film silicon solar cells. Thus lunar surface possesses both the elemental components needed for the fabrication of silicon solar cells and a vacuum environment that allows for vacuum deposition of thin film solar cells directly on the surface of the Moon without the need for vacuum chambers. In support of the US space exploration initiative a new architecture for the production of thin film solar cells on directly on the lunar surface is proposed. The paper discusses experimental data on the fabrication and properties of lunar glass substrates, evaporated lunar regolith thin films (anti-reflect coatings and ...

International Nuclear Information System (INIS)

One of the initial stages in ecological risk assessment for hazardous waste sites is the screening of contaminants to determine which of them are worthy of further consideration as ''contaminants of potential concern.'' This process is termed ''contaminant screening.'' It is performed by comparing measured ambient concentrations of chemicals to benchmark concentrations. Currently, no standard benchmark concentrations exist for assessing contaminants in soil with respect to their toxicity to plants. This report presents a standard method for deriving benchmarks for this purpose (phytotoxicity benchmarks), a set of data concerning effects of chemicals in soil or soil solution on plants, and a set of phytotoxicity benchmarks for 34 chemicals potentially associated with US Department of Energy (DOE) sites. Chemicals that are found in soil at concentrations exceeding both the phytotoxicity benchmark and the background concentration for the soil type should be considered ...

CERN Document Server

Automatic Repeat Request (ARQ) is an effective technique for reliable transmission of packets in wireless networks. In ARQ, however, only a few erroneous bits in a packet will cause the entire packet to be discarded at the receiver. In this case, it's wasteful to retransmit the correct bit in the received packet. The partial packet recovery only retransmits the unreliable decoded bits in order to increase the throughput of network. In addition, the cooperative transmission based on Interleave-division multiple-access (IDMA) can obtain diversity gains with multiple relays with different locations for multiple sources simultaneously. By exploring the diversity from the channel between relay and destination, we propose a relay-assisted partial packet recovery in CDMA wireless network to improve the performance of throughput. In the proposed scheme, asynchronous IDMA iterative chip-by-chip multiuser detection is utilized as a method of multiple ...

International Nuclear Information System (INIS)

The main problems arising in decommissioning nuclear-powered submarines (NPS) relate to choosing a concept of handling reactor compartments followed by handling technology development. Reactor compartments (RC) are characterized with extremely space-saving or integral layout of large-size power equipment and systems, restricted access for dismantling, high radiation dose rates in a number of bays of RC. The above RC features pose a problem to find optimum option of RC utilization which on the one hand would be the most cost efficient, and the safest as possible on the other, i.e. dose commitments of personnel involved should be minimum, and effect on population and environment should be negligible. The main radiation factors specifying safety in RC handling at any decommissioning stage are as follows: (1) total radioactivity integrated in reactor facility (RF); (2) distribution of this radioactivity through RF equipment and structures; (3) forms the radioactivity ...

Science.gov (United States)

A one-year technology-transfer project involving ERDA installations and Hawaii consisted of sending teams from the Lawrence Livermore Laboratory on week-long field trips every two months to test the effectiveness of different methods of transferring technology information from federal sources to civilian clients. The team was questioned primarily on non-energy matters, and the energy questions asked related mostly to individuals or small industries. The team responed to all questions and found that a wide range of knowledge was more effective than having a sequence of experts. Hawaiians considered current major ERDA projects to be irrelevant to their needs. The team was most successful on a one-to-one basis because large groups and state agencies tend to be more policy- than action-oriented. Personal followup was considered essential. The team also learned that their visits generated ten times as many inquiries as were received unsolicited by the laboratory. Most inquiries involved ...

International Nuclear Information System (INIS)

In the utilization of the thermal energy by ocean temperature difference and factory waste heat, the high performance heating surfaces in pipes from which scale can be removed are required. As the method of removing scale, the method using sponge balls seems most suitable, but for applying this method, as the form of the protrusions attached to the inner surfaces of pipes, smooth circular are form is desirable. The promotion of heat transfer with the rows of circular arc protrusions like this is strongly related to the mode of flow and such structure as separation, recirculation flow, readhesion and turbulent energy generation. In this study, as the basic research to optimize the heating surface with the rows of smooth protrusions, the flow characteristics and the heat transfer characteristics including the turbulent structure of the wake of protrusions were experimentally determined, and the essence of the heat transfer characteristics was to ...

British Library Electronic Table of Contents (United Kingdom)

Passion fruit (Passiflora edulis f. flavicarpa L.) yellow variety is composed of 50-55g peel per 100g of fresh fruit which is discarded as waste during processing. Utilization of passion fruit peel for pectin extraction was studied. Passion fruit peel obtained after juice extraction was blanched in boiling water for 5min, dehydrated in a cross flow hot air drier at 60+-1degreeC to a moisture content of 4g/100g of dried peel. The dehydrated passion fruit peel was used for extraction experiments of pectin. The effect of pH, peel to extractant ratio, and number of extractions, extraction time and temperature on the yield and quality characteristics of pectin were investigated. The optimized conditions for extraction of pectin from passion fruit peel yielded 14.8g/100g of dried peel. Pectin ex...

Energy Technology Data Exchange (ETDEWEB)

The results from a hot test, using authentic HLLW solution, of the CTH actinide separation process are reported. The process consists of three solvent extraction cycles for separation of actinides and technetium from reprocessing high level liquid waste, utilizing HDEHP, TBP, and HDEHP in sequence, and an optional step for sorption on inorganic ion exchangers of the fission product content in the process raffinate. In general the process worked according to predictions but a malfunctioning feed pump gave a 10% loss of Pu to one stream. The hot test indicating that U and Pu can be recovered with losses below 0.1% and Am, Cm with a loss below 0.2%. Np and Tc were difficult to follow because of the low activity of /sup 237/Np and because /sup 99/Tc is a pure beta emitter, but the results indicate that also these elements behaved according to predictions, i.e., that recoveries >= 99.8% for Np and >= 97% for Tc can be achieved. For the HLLW ...

Science.gov (United States)

The Process Waste Treatment Plant (PWTP) at the Oak Ridge National Laboratory is designed to remove radioactive contaminants, principally {sup 90}Sr, from process wastewater. Planned upgrades to the PWTP will use chabazite zeolite columns. Pilot-scale studies have shown that mass transfer zone lengths increase from 10 to about 30 cm as the superficial velocity increases from 5.5 to 22 cm/min. Calculations with a multicomponent equilibrium model showed that the distribution coefficient for strontium remains essentially constant over the process conditions, suggesting that a simple kinetic model (the Rosen long-bed solution) should adequately represent breakthrough behavior. Using a distribution coefficient of 4.87 L/g predicted by the equilibrium model, good agreement was found between experimental breakthrough curves and those calculated with the Rosen solution. This model allows prediction of bed depths and cycle times necessary to achieve the required ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of the Hanford Waste Management Plan (HWMP) is to provide an integrated plan for the safe storage, interim management, and disposal of existing waste sites and current and future waste streams at the Hanford Site. The emphasis of this plan is, however, on the disposal of Hanford Site waste. The plans presented in the HWMP are consistent with the preferred alternative which is based on consideration of comments received from the public and agencies on the draft Hanford Defense Waste Environmental Impact Statement (HDW-EIS). Low-level waste was not included in the draft HDW-EIS whereas it is included in this plan. The preferred alternative includes disposal of double-shell tank waste, retrievably stored and newly generated TRU waste, one pre-1970 TRU solid waste site near the Columbia River ...

Energy Technology Data Exchange (ETDEWEB)

It was previously reported that the tritium tracer method is useful for the quantitative consideration of hydrogen behavior in coal during coal liquefaction reaction. Tetralin is excellent hydrogen donating solvent, and is considered as one of the model compounds of coal. In this study, effects of H2S and H2O on the hydrogen exchange reaction between tetralin and gaseous hydrogen labeled by tritium were investigated. It was suggested that the conversion of tetralin and the hydrogen exchange reaction between gaseous hydrogen and tetralin proceed through the radical reaction mechanism with a tetralyl radical as an intermediate product. When H2S existed in this reaction, the hydrogen exchange yield increased drastically without changing the conversion yield. This suggested that the hydrogen exchange reaction proceeds even ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Surface crystallization and surface-to-bulk ratio in high-level waste glasses.

Science.gov (United States)

Sep 2, 2008 ... Abstract: This tutorial is intended to serve as a guide towards proper hazardous waste management. Knowing the regulations, different ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

We have investigated the stability and catalytic activity of epitaxial overlayers of rhodium on Au(111) and Pd(111). Both surfaces show a strong affinity for hydrogen. We have calculated the energy of adsorption both for a strongly and a more weakly adsorbed species; the latter is the intermediate in the hydrogen evolution reaction. Both the energy of activation for hydrogen adsorption (Volmer reaction) and hydrogen recombination (Tafel reaction) are very low, suggesting that these overlayers are excellent catalysts. PMID:21847482

Energy Technology Data Exchange (ETDEWEB)

Earlier work carried out on the hydrogen-diesel dual-fuel engine indicates that knock sets in when the inducted hydrogen exceeds about 60% of input energy with a pilot quantity of 30% of full load diesel amount. Some of the findings of an investigation into knock-free performance of a hydrogen-diesel dual-fuel engine with the addition of a diluent-carbon dioxide are presented. The effects of carbon dioxide on the suppression of knocking in the hydrogen-diesel dual-fuel engine and on the improvement in the knock limited power output are described.

Science.gov (United States)

This request is submitted to seek interim approval to operate a Toxic Substances Control Act (TSCA) of 1976 chemical waste landfill for the disposal of polychlorinated biphenyl (PCB) waste. Operation of a chemical waste landfill for disposal of PCB waste ...

Energy Technology Data Exchange (ETDEWEB)

Implementation of a plan to charge waste management costs to the facility that generates such waste requires a long-term commitment and consistent administration. The benefit is that generators are provided the incentive to optimize waste management practices if the charges are appropriately applied. This paper summarizes (1) a plan to charge waste generators, (2) the administrative structure of the plan, (3) a comparison between the rate structure and changes in waste disposal operations, and (4) issues that have surfaced as the plan is implemented. 2 refs., 1 fig., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

Various methods for storing hydrogen have been examined in an effort to find ways to store hydrogen in increasingly smaller volumes with decreasing weight of the whole hydrogen storage system. Metal hydrides, in which hydrogen is chemically bound to a metal atom, are considered to be very promising candidates for hydrogen storage because they have high gravimetric and volumetric storage capacities. This study investigated the effect of different magnesium (Mg) and aluminium (Al) ratios on the absorption and desorption properties of thin films. Neutron reflectometry (NR) was used in this study to better understand the absorption and desorption properties of commercially promising hydrogen storage materials. The large negative scattering length of hydrogen atoms changes the reflectivity curve substantially, so that NR can determine the total ...

International Nuclear Information System (INIS)

Hospital wastes comprises approximately 80% domestic waste components, also known as non-risk waste and 20% hazardous or risk waste. The 20% of the hospital waste stream or the risk waste (also known as infectious, medical, clinical wastes) comprises components which could be potentially contaminated with infections, chemical or radioactive agents. Therefore, it should be handled and disposed of in such a manner as to minimize potential human exposure and cross-contamination. Hospital risk waste and be subdivided into seven general categories as follows: infections, anatomical/pathological, chemical, pharmaceutical, radioactive waste, sharps and pressurised containers. These waste categories are generated by many types of health care establishments, including hospitals, clinics, ...

Energy Technology Data Exchange (ETDEWEB)

A fermentation waste, Corynebacterium glutamicum, was successfully employed as a biosorbent for Reactive Black 5 (RB5) from aqueous solution. This paper initially studied the effect of pretreatment on the biosorption capacity of C. glutamicum toward RB5, using several chemical agents, such as HCl, H{sub 2}SO{sub 4}, HNO{sub 3}, NaOH, Na{sub 2}CO{sub 3}, CaCl{sub 2} and NaCl. Among these reagents, 0.1 M HNO{sub 3} gave the maximum enhancement of the RB5 uptake, exhibiting 195 mg/g at pH 1 with an initial RB5 concentration of 500 mg/l. The solution pH and temperature were found to affect the biosorption capacity, and the biosorption isotherms derived at different pHs and temperatures revealed that a low pH (pH 1) and high temperature (35 deg. C) favored biosorption. The biosorption isotherm was well represented using three-parameter models (Redlich-Peterson and Sips) compared to two-parameter models (Langmuir and Freundlich models). As a result, high correlation ...

Energy Technology Data Exchange (ETDEWEB)

A study was undertaken to examine the uptake, distribution, and interaction of five activation products (Co-57, Be-7, Cs-134, Rb-83, and Mn-54) within the biotic and abiotic components surrounding the waste treatment lagoons of the Los Alamos Meson Physics Facility (LAMPF). The study attempted to ascertain where, and what specific interactions were taking place among the isotopes and the biotic/abiotic components. A statistical approach, utilizing Multivariate Analysis of Variance (MANOVA), was conducted testing the radioisotopic concentrations by (1) the trophic levels (TROPLVL) in each position sampled on the grid, (2) where sampled on the grid (TRAN), (3) where sampled with-in each grid line (PLOT), and (4) the side with which sampled (SIDE). This provided both the dependent and independent variables that would be tested. The Null Hypothesis (Ho) tested the difference in the mean values of the isotopes within/between each of the four ...

Science.gov (United States)

The Savannah River Site (SRS) is a 310-square-mile United States Department of Energy nuclear facility located along the Savannah River (SRS) near Aiken, South Carolina. Nuclear weapons material production began in the early 1950s, utilizing five production reactors. In the early 1990s all SRS production reactor operations were terminated. The first reactor closure end state declaration was recently institutionalized in a Comprehensive Environmental Response and Compensation and Liability Act (CERCLA) Early Action Record of Decision. The decision for the final closure of the 318,000 square foot 105-P Reactor was determined to be in situ decommissioning (ISD). ISD is an acceptable and cost effective alternative to off-site disposal for the reactor building, which will allow for consolidation of remedial action wastes generated from other cleanup activities within the P Area. ISD is considered protective by the regulators, U. S. Environmental ...

Energy Technology Data Exchange (ETDEWEB)

Tanzania has recently developed a comprehensive environmental policy which has put high priority on several specific environmental issues. One of the issues is the quality of waste water. A special priority is given to the pollution from the sisal industry. The East-African agro-industries generate very large quantities of organic residues from production and processing of different crops. These residues form a major contribution to the pollution of air, soil and waterways, but, at the same time they constitute a large potential for production of bioenergy through anaerobic digestion as well as potential substrate for other biological fermentation processes. Generally, these residues are regarded as having no or very little value and the different disposal methods are mainly a matter of getting rid of the waste. The generation of residues are very often concentrated on few large units, which makes the exploitation of these resources feasible in ...

Energy Technology Data Exchange (ETDEWEB)

Some comments are given on the recycling of waste, mainly plastics, as evaluated from the viewpoint of energy environment. Discussed about the waste in general are the definition and classification, generation and resource recovery rates, current state of recycling, problems about recycling, related legislation, and current conditions overseas. Discussed about the treatment and recycling of plastics waste are the characters and use of plastic product, current state of waste plastics treatment, current state of waste plastics recycling (material recycling, thermal recycling), energy recovery by thermal recycling, quantity recyclable from waste plastics, energy consumption and cost for waste plastics recycling, effect and impact of increase in waste plastics in case material recycling is forwarded, and prospect of ...

Energy Technology Data Exchange (ETDEWEB)

In this study, the effects of hydrogen peroxide on laminar, premixed, methane-air flames at atmospheric pressure and temperature were investigated using CHEMKIN III and GRI 3.5 mechanism. The range of fuel/air equivalence ratio {phi} was varied from 0.6 to 1.2, and the amount of hydrogen peroxide was altered from 0% to 20% volumetric fraction of the methane-hydrogen peroxide (air excluded) mixture. The burning velocity was found to increase with increasing hydrogen peroxide addition, with a relatively larger increase for the fuel-richer mixtures ({delta}S{sub u} up to 15 cm/s for {phi} {approx}=1.2). The adiabatic flame temperature rose with hydrogen peroxide addition, and the temperature rise per unit hydrogen peroxide addition was more significant ({delta}T up to 100 K) for the leaner mixtures. For the same mixture stoichiometry, adding ...

Energy Technology Data Exchange (ETDEWEB)

Substantial roles of precipitates such as Zr-Fe-Cr type intermetallic compounds on uniform corrosion and hydrogen pickup of zirconium alloys in pure water autoclave tests were investigated from an electrochemical point of view. In the previous paper, corrosion mechanism was elucidated by the anodic protection-precipitates degradation model. This paper describes the roles on hydrogen pickup. 633 K pure water autoclave test was performed on high purity zirconium, Zr-0.2Fe, Zr-0.2Cr, and Zr-0.1Fe-0.1Cr alloys. Hydrogen analysis after the corrosion test showed that hydrogen pickup ratio of Zr-0.2Fe alloy was about 80%. It was much higher than about 30% of pure Zr and about 10% of both Zr-0.2Cr and Zr-0.1Fe-0.1Cr alloys. Larger hydrogen content was introduced into Zr-0.2Fe alloy than the other ones by the cathodic hydrogen charging under coulombic equivalence. The ...

Energy Technology Data Exchange (ETDEWEB)

The turbulent history of legislature concerned with the waste-management industry and the amount of material on this subject as well as the significance of the material in its own right led to the decision to publish all legal regulations on waste in one volume. It includes above all the Waste Law, Regulations on Determination of Waste, Regulations on Determination of Residual Products, Technical Instructions for Waste, Regulations for Monitoring Waste and Residual Products, Regulations on Probition from the Use of Chlorofluorohydrocarbons and Halon, Regulations on Packaging and Regulations on Sewage Sludge. The introduction explains the development and the role of the Waste Law and its applicability, goals and principles: The concept of waste, avoidance of waste, avoidance of ...

Energy Technology Data Exchange (ETDEWEB)

In response to US Department of Energy directives, Argonne National Laboratory (ANL) has developed a waste minimization plan aimed at reducing the amount of wastes at this national research and development laboratory. Activities at ANL are primarily research- oriented and as such affect the amount and type of source reduction that can be achieved at this facility. The objective of ANL's waste minimization program is to cost-effectively reduce all types of wastes, including hazardous, mixed, radioactive, and nonhazardous wastes. The ANL Waste Minimization Plan uses a waste minimization audit as a systematic procedure to determine opportunities to reduce or eliminate waste. To facilitate these audits, a computerized bar-coding procedure is being implemented at ANL to track hazardous wastes ...

Energy Technology Data Exchange (ETDEWEB)

Results of a survey conducted by Concawe on 75 oil refineries in Europe show that the total quantity of waste requiring disposal in 1986 was 0.5 million metric tons. This quantity of waste is but 0.13% of the total refinery throughput of 387 million metric tons during 1986. The survey revealed a wide range of disposal costs, depending on the particular properties of the waste and local conditions. A summary of total waste generation and how the waste is disposed of is shown. Details on the types of waste disposed, the disposal methods used, and the costs of disposal are detailed in this excerpt from the Concawe survey.

Science.gov (United States)

This Waste Management Plan functions as a management and planning tool for managing waste streams generated as a result of operations at the Idaho CERCLA Disposal Facility (ICDF) Complex. The waste management activities described in this plan support the selected remedy presented in the Waste Area Group 3, Operable Unit 3-13 Final Record of Decision for the operation of the Idaho CERCLA Disposal Facility Complex. This plan identifies the types of waste that are anticipated during operations at the Idaho CERCLA Disposal Facility Complex. In addition, this plan presents management strategies and disposition for these anticipated waste streams.

International Nuclear Information System (INIS)

A series of hydrogenation/dehydrogenation cycles have been performed on palladium wire samples, stressed by a constant mechanical tension, in order to investigate the changes in electrical and mechanical properties. A large increase of palladium electrical resistivity has been reported due to the combined effects of the production of defects linked to hydrogen insertion into the host lattice and the stress applied to the sample. An increase of the palladium sample strain due to hydrogenation/dehydrogenation cycles in ????? phase transitions is observed compared to the sample subjected to mechanical tension only. The loss of initial metallurgical properties of the sample occurs already after the first hydrogen cycle, i.e. a displacement from the initial metallic behavior (increase of the resistivity and decrease of thermal coefficient of resistivity) to a worse one occurs already after the first ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a method of reducing the hydrogen sulfide level in streams containing hydrogen sulfide at concentrations from about 2 ppm up to about 1,000 ppm. It comprises reacting the hydrogen sulfide with an unsaturated hydrocarbon in the presence of an acidic solid catalyst selected from the group consisting of polymeric sulfonic acid resins, solid polyphosphoric acid, supported sulfuric acid, supported boric acid, silica-aluminas, clays, faujasite, mordenite, and L, omega, X or Y zeolites at mercaptan-forming concentrations, and recovering a stream having a reduced hydrogen sulfide concentration and containing no more than 5 ppm hydrogen sulfide.

Energy Technology Data Exchange (ETDEWEB)

A method for determining the mobility of hydrogen as a function of temperature in superconducting niobium cavities comprising: 1) heating a cavity under test to remove free hydrogen; 2) introducing hydrogen-3 gas into the cavity; 3) cooling the cavity to allow absorption of hydrogen-3; and 4) measuring the amount of hydrogen-3 by: a) cooling the cavity to about 4.degree. K while flowing a known and regulated amount of inert carrier gas such as argon or helium into the cavity; b) allowing the cavity to warm at a stable rate from 4.degree. K to room temperature as it leaves the chamber; and c) directing the exit gas to an ion chamber radiation detector.

CERN Document Server

Although hydrogen is the simplest of atoms, it does not form the simplest of solids or liquids. Quantum effects in these phases are considerable (a consequence of the light proton mass) and they have a demonstrable and often puzzling influence on many physical properties, including spatial order. To date, the structure of dense hydrogen remains experimentally elusive. Recent studies of the melting curve of hydrogen indicate that at high (but experimentally accessible) pressures, compressed hydrogen will adopt a liquid state, even at low temperatures. In reaching this phase, hydrogen is also projected to pass through an insulator-to-metal transition. This raises the possibility of new state of matter: a near ground-state liquid metal, and its ordered states in the quantum domain. Ordered quantum fluids are traditionally categorized as superconductors or superfluids; these respective ...

Energy Technology Data Exchange (ETDEWEB)

Three different configurations of cylindrical submerged media anaerobic reactors (SMARs) with packing volumes of 85 items were operated at 35 C for 415 days with COD loading rates varying from 1 to 12 g/l/d and three retention times of 0.5, 1, and 2 days. A synthetic waste consisting of a milk solution with a mineral supplement was used for the feed. Tracer studies on clean-bed and dirty-bed SMARs indicate that reactor configuration, biogas mixing, and biomass accumulation all have a significant effect on SMAR hydraulics and cause short-circuiting. Based on the isothermal energy dissipation theory, the higher hydrostatic pressures resulting from higher SMAR heights increases self-induced biogas mixing and improves the contact efficiency between substrate and organisms. Based on TCOD removal rate, the tallest SMAR performed slightly better at COD loading rates above 4/g/l/d. At COD loading rates equal to or below 4 g/l/d, there was little difference in TCOD removal ...

Energy Technology Data Exchange (ETDEWEB)

The `biotechnology 2000` project is supervised by the project sponsor `biology, energy, ecology` at Forschungszentrum Juelich on behalf of the Federal Ministry for Research and Technology. The project activities cover the development of techniques and methods, cell biology, gene structure and gene regulation, photosynthetic production processes, biological hydrogen production, synthetic biology, protein design, neurobiological research, biosystems, plant breeding, phytomedicine and plant protection, the biology of waste disposal methods, research into methods which replace animal experiments, biological safety research, technology risk assessment, and ethical aspects. A general survey introduces the promoted projects, and standardized data sheets briefly introduce the individual activities. The appendix gives the project indices, the indices of joint projects, a list of the supported companies and institutions, and the project sponsor ...

Energy Technology Data Exchange (ETDEWEB)

In relation to considerations on composition of gas produced by coal gasification, the HYCOL hydrogen generation process data were analyzed. From the fact that CO concentration (Y) decreases linearly with CO2 concentration (X), element balance of gasification of reacted coal was used to introduce a reaction analysis equation. The equation includes a term of oxygen excess {Delta}(amount of oxygen consumed for combustion of CO and H2 in excess of the theoretical amount), derived by subtracting the stoichiometric oxygen amount used to gasify coal into CO and H2 from the consumed oxygen amount. The {Delta} can be used as a reference to oxygen utilization efficiency. An equation for the {Delta} was introduced. Also introduced was a term for steam decomposition amount derived by subtracting the generated steam from the supplied steam. These terms may be used as a clue to permeate into the gasifying reaction process. This suggestion was discussed by ...