Energy Technology Data Exchange (ETDEWEB)

The energy available from tidal currents is substantial and considerable work has been conducted into determining the size of the resource and what the large-scale consequences of extraction might be. This paper describes the work conducted to establish a laboratory-scale model, by using the commercial computational fluid dynamics (CFD) code FLUENT trademark, in order to predict local-flow consequences resulting from the extraction of energy in two and three dimensions from within the water column in a tidal flow. As might be expected, a wake is formed but there is considerable localized flow acceleration around and, most especially, under an extraction zone. The wake behind the device is shown to be associated with a drop in the free surface which, in turn, is associated with the decline in the wake itself. (author)

Energy Technology Data Exchange (ETDEWEB)

Numerical investigations of three-dimensional flow and heat transfer in a finned tube with punched longitudinal vortex generators (LVG`s) are carried out for Reynolds number of 250 and 300. Air with a Prandtl number of 0.7 is used as the fluid. The flow is both thermally and hydrodynamically developing. The LVG is a delta winglet pair (DWP) punched out of the fin and is located directly behind the tube, symmetrically separated by one tube diameter. The DWP generates longitudinal vortices in the wake of the tube, defers flow separation on the tube, deflects the main stream into the tube wake, and strong reduces the ``dead water zone.`` Heat transfer reversal is avoided by the DWP. Comparison of the span-averaged Nusselt numbers for the fin with and without DWP shows significant local heat transfer enhancement of several hundred percent in the tube wake. For Re = 300 and Fi = 200 the global heat transfer augmentation by a ...

British Library Electronic Table of Contents (United Kingdom)

Concerning the requirements of future rocket technologies, providing a cost-efficient access to orbit as well as an increase in system reliability, a deeper insight into the unsteady phenomena during ascent of modern launchers is essential. Unsteady interactions and resonances of the turbulent separated launcher wake and the nozzle structure play an important role for the design of future main stage propulsion systems. The so-called buffeting coupling phenomenon is one of the main challenges during ascent. In the present study, a coupled simulation of the afterbody of the Ariane-5 launcher with a realistic structural and aerodynamic representation of different nozzle configurations is carried out. On the computational fluid dynamics side, unsteady detached eddy simulations are coupled with...

International Nuclear Information System (INIS)

2001 p. 267-268 Brazil Perry, Katia SP Ferreira, Andre RG Amorim, Mauro

Energy Technology Data Exchange (ETDEWEB)

The technology status of the dynamics and controls discipline as it applies to energy storage wheel systems was evaluated. No problems were identified for which an adequate solution could not be proposed. Design issues that influence control were addressed. The dynamics and control aspects associated with the energy storage system concept and its various constituent parts, and the control tasks attendant to large, manned spacecraft are discussed.

UK PubMed Central (United Kingdom)

BackgroundApproximately 25% of ischemic stroke patients awaken with neurological deficits. In these patients, in whom the time from symptom onset is uncertain, brain imaging is a...Full Text Available

Medline Plus

ROBOT-ASSISTED RADICAL LAPAROSCOPIC PROSTATECTOMY WAKE FOREST UNIVERSITY BAPTIST MEDICAL CENTER WINSTON-SALEM, NC 00:00:08 ANTHONY ATALA, MD: I would like ...

Science.gov (United States)

verse pressure gradient, makes it susceptible to flow separation, ...... AGARD, Lecture Series LS-167. [25] Eifler, J., 1975, Zur Frage der freien ...

Science.gov (United States)

The jet in cross flow (JICF) is a basic flowfield which is relevant to a wide variety of applications which are described to provide context for JICF investigations. Material consistent with the scope of topics presented at the 72nd AGARD Fluid Dynamics Panel Meeting and Symposium on Computational and Experimental Assessment of Jets in Cross Flow on 19-22 April 1993 in Winchester, U.K. is summarized. The JICF research was divided into three time periods: (1) early research - up to 1970, (2) research during the 1970's, and (3) research since 1980. The following areas of experimental activity are discussed; the definition of an effective correlation parameter; the jet flowfield including the jet trajectories, cross-section shape, and jet induced pressures; the effects of jet deflection angle, nozzle shape, pressure ratio, velocity decay, and temperature; and the effect of confined flowfield, ground effects, multiple jets, and adjacent surface geometry. In addition, ...

CERN Document Server

After two decades of direct dynamical simulation of large-scale structure in the universe, it is safe to say the subject is now mature. Still, there are parts of the problem that are less well developed than others. In general, the collisionless dynamics of the dark matter component is better understood than the collisional gas dynamics of the baryonic component. In situations where the gas dynamics is relatively simple, such as the Lyman-$\\alpha$ forest and the intracluster medium in X-ray clusters, our ability to reproduce observational data has evolved rapidly, and the interpretive and predictive power of such experiments should now be taken seriously. A comparison of twelve gas dynamic codes to the problem of forming a single X-ray cluster shows that numerical inaccuracies are modest (typically below ten percent), leaving missing physics as the main source ...

UK PubMed Central (United Kingdom)

Realization that dental caries is a reversible, dynamic biochemical event at a micron level has changed the way the profession recognizes the caries disease and the caries lesion. The diagnosis of dental...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows:In the current thermal-hydraulic system analysis codes using the two-fluid model, the empirical correlations that are based on the two-phase flow regimes and regime transition criteria are being employed as closure relations for the interfacial transfer terms. Due to its inherent shortcomings, however, such static correlations are inaccurate and present serious problems in the numerical analysis. In view of this, a new dynamic approach employing the interfacial area transport equation has been studied. The interfacial area transport equation dynamically models the two-phase flow regime transitions and predicts continuous change of the interfacial area concentration along the flow field. Hence, when employed in the thermal-hydraulic system analysis codes, it eliminates artificial bifurcations stemming from the use of the static flow regime transition criteria. Therefore, the interfacial area transport equation ...

Energy Technology Data Exchange (ETDEWEB)

Distribution of Lipiodol within hepatic tumor was evaluated using serial computed tomography. Imagistic Lipiodol transition into the tumor via hepatic artery was slower than that of water soluble contrast medium, spreading to central part first and turn to peripheral part of the tumor. This method was thought to be useful to clarify Lipiodol distribution in hepatic tumor and to decide the method or necessity of additional trans-arterial therapy. (author).

British Library Electronic Table of Contents (United Kingdom)

In this article we derive longitudinal impedance and wake function for an undulator setup with arbitrary undulator parameter, taking into account a finite transverse size of the electron bunch. Earlier studies considered a line density-distribution of electrons instead. We focus our attention on the long-wavelength asymptote (compared with resonance wavelength), at large distance of the electron bunch from the undulator entrance compared to the overtaking length, and for large vacuum-chamber size compared to the typical transverse size of the field. These restrictions define a parameter region of interest for practical applications. We calculate a closed expression for impedance and wake function that may be evaluated numerically in the most general case. Such expression allows us to deriv...

British Library Electronic Table of Contents (United Kingdom)

In this paper linear and nonlinear models of spacecraft attitude dynamics equations and gravity gradient moments are investigated. In addition, effects of gravity gradient moments on attitude dynamics of the satellite are studied. The purpose of this paper is to present a comparison between nonlinear and linear models of spacecraft attitude dynamics and gravity gradient moments in order to determine divergence of linear approximation from the nonlinear model. Simulation results indicate that designer of spacecraft attitude control subsystem should be meticulous in applying linear approximation of equations especially in low earth orbits. Consequently, finding an upper bound for small angle to keep the linear model valid and precise enough would be a vital part of using linear approximation...

Science.gov (United States)

especially since your attack several years ago. I was wondering, in the wake of WikiLeaks, what the Estonians can help the U.S. with in terms of developing an - as...

Energy Technology Data Exchange (ETDEWEB)

In this article we derive longitudinal impedance and wake function for an undulator setup with arbitrary undulator parameter, taking into account a finite transverse size of the electron bunch. Earlier studies considered a line density-distribution of electrons instead. We focus our attention on the long-wavelength asymptote (compared with resonance wavelength), at large distance of the electron bunch from the undulator entrance compared to the overtaking length, and for large vacuumchamber size compared to the typical transverse size of the field. These restrictions define a parameter region of interest for practical applications. We calculate a closed expression for impedance and wake function that may be evaluated numerically in the most general case. Such expression allows us to derive an analytical solution for a Gaussian transverse and longitudinal bunch shape. Finally, we study the feasibility of current-enhanced SASE schemes (ESASE) ...

Science.gov (United States)

... (v) Import onto or keep on Wake Island any plant or animal not indigenous to the island, other than military working dogs or a guide dog for the blind or visually-impaired accompanying its owner; or (w) Import or bring onto or...

Energy Technology Data Exchange (ETDEWEB)

Remotely-fielded unattended sensor networks generally must operate at very low power--in the milliwatt or microwatt range--and thus have extremely limited communications bandwidth. Such sensors might be asleep most of the time to conserve power, waking only occasionally to transmit a few bits. RFID tags for tracking or material control have similarly tight bandwidth constraints, and emerging nanotechnology devices will be even more limited. Since transmitted data is subject to spoofing, and since sensors might be located in uncontrolled environments vulnerable to physical tampering, the high-consequence data generated by such systems must be protected by cryptographically sound authentication mechanisms; but such mechanisms are often lacking in current sensor networks. One reason for this undesirable situation is that standard authentication methods become impractical or impossible when bandwidth is severely constrained; if messages are small, a standard digital ...

International Nuclear Information System (INIS)

The dynamics of transportation, accumulation, disappearance and distribution of "6"0Co in the wheat-soil system was studied by using isotope-tracer techniques for simulated pollutants, and the mathematical model of the behavior was established. Rescilts showed that (1) "6"0Co was transported rapidly in the system after the application on soil surface layer. The uptake of "6"0Co by wheat was mainly via root, and redistribution in all parts of wheat occurred consequently. The concentration in root was much higher than that in other parts of wheat plant. The specific activity of "6"0Co in wheat plant rapidly increased to a maximum value, then decreased. The specific activity of "6"0Co in each part of wheat plant was found in the order of root > straw > husk > seed. (2) "6"0Co is mainly detained with in 6cm of soil surface, and specific activity of "6"0Co in soil present a simple exponential ...

CERN Document Server

Denial of service attacks (DoS) can cause significant financial damages. Flooding and Malicious packets are two kinds of DoS attacks. This paper presents a new security approach which stops malicious packets and prevents flooding in the critical systems. New concepts of packet stamp a dynamic-multi-communication-point mechanism has been identified for this proposed approach to make the prevention of flooding attacks easier and the performing of malicious packet attacks harder. In addition, dynamic key encryption technique has been adapted as a part of the proposed approach to enhance its functionality.

Energy Technology Data Exchange (ETDEWEB)

As part of a comprehensive simulation of a prototype locomotive propulsion system, a detailed model has been developed which predicts the dynamic response of an experimental 2-stroke, turbocharged and intercooled diesel engine. Engine fueling and brake torque are computed from regression equations derived from an extensive data base. Corrections are applied to the calculated steady-state torque to account for dynamic deviations of in-cylinder trapped air-fuel ratio from the steady-state value. The engine simulation accurately represents the operation of the turbo-charger, which is gear-driven at low turbocharger speeds, and freewheels through an overrunning clutch when exhaust energy accelerates the turbocharger beyond its geared speed. Engine fueling level, ie, rack, is determined from a dynamic simulation of an electrohydraulic governor which responds to the difference between the desired and the ...

Energy Technology Data Exchange (ETDEWEB)

This study was aimed to test and select hydrophobic activated charcoal, manufactured in Romania, used as adsorbents of solvents which partly compose diluters employed in car industry. With regard to the diluters, three of the seven types of activated charcoal studied (Sorbent 1, R - Cafs and AD3) showed the greatest capacity of adsorption, when determined under dynamic and static conditions. (authors) 8 refs.

International Nuclear Information System (INIS)

In this article we derive longitudinal impedance and wake function for an undulator setup with arbitrary undulator parameter, taking into account a finite transverse size of the electron bunch. Earlier studies considered a line density-distribution of electrons instead. We focus our attention on the long-wavelength asymptote (compared with resonance wavelength), at large distance of the electron bunch from the undulator entrance compared to the overtaking length, and for large vacuum-chamber size compared to the typical transverse size of the field. These restrictions define a parameter region of interest for practical applications. We calculate a closed expression for impedance and wake function that may be evaluated numerically in the most general case. Such expression allows us to derive an analytical solution for a Gaussian transverse and longitudinal bunch shape. Finally, we study the feasibility of current-enhanced SASE schemes (ESASE) ...

Energy Technology Data Exchange (ETDEWEB)

This article provides a survey of neutron scattering experiments in condensed matter research, which are of interest to chemistry. The theoretical background has been treated in a previous issue. The present article consists of two parts. The first part exhibits the range of experimental possibilities by means of a few selected examples. The starting point is classical neutron diffraction by which the position of atomic nuclei may be determined. Additional information on the spatial distribution in the outer electron shells may be obtained via combined X-ray/neutron-diffraction experiments or via the diffraction of polarized neutrons. Progress in instrumentation, due to the development of more intense sources, has influenced especially the fields of small angle scattering and spectroscopy. The second part features domains of research of current interest, where a combination of several neutron scattering techniques may prove ...

CERN Document Server

Dynamic system identification

International Nuclear Information System (INIS)

Stimulated bremsstrahlung in an undulating electric field in the lasing beam direction (electric wiggler) was shown to be possible from the quantum- mechanical viewpoint. Herein, this possibility is scrutinized from the viewpoint of classical electrodynamics. It is found that if stimulated bremsstrahlung in a transverse undulating magnetic field (magnetic wiggler) occurs, stimulated bremsstrahlung in the electric wiggler must also occur. We further show that a free electron laser (FEL) using a magnetic wiggler to provide a catalyzer field for stimulated bremsstrahlung cannot serve as a practical FEL operating in the soft x-ray region from both theoretical and experimental viewpoints. On the other hand, the authors demonstrate that the FEL using a traveling wake field in a two-beam elliptical pill-box cavity is well suited as a source of coherent radiation in the soft x-ray region.

International Nuclear Information System (INIS)

We present a unified description of the imaginary part of the dynamical magnetic susceptibility #chi#"'"'(#omega#.T) and measurements of the static susceptibility #chi#(T) and electrical resistivity #rho#(T) in the uranium intermetallics UCu_5_-_xPd_x (x = 1.1.5). For temperatures T and excitation energies #omega# in the range 12 K < #omega#, T < 150 K, our analysis demonstrates that the dynamics of isolated uranium ions are responsible for the observed temperature and frequency scaling, although interion interactions may become important at lower temperatures and frequencies. We derive a strict criterion for single-ion scaling in the form of a universal scaling function, providing a model-independent description of the compiled experimental data. (orig.).

CERN Document Server

One of the major challenges facing the proposed high-energy linear e^+e^ colliders is the preservation of the extremely small vertical emittance from the damping rings to the interaction point (IP). This emittance must be transported through bunch compression sections, the main linac and finally through the beam delivery system to the IP. Historically, the beam dynamics issues of each subsystem have been studied quasi-independently, with the beam conditions and tolerances being specified at the boundaries. As part of the recent International Linear Collider Technical Review Committee, new simulation tools have been developed to simulate the beam transport through the integrated system, including static and dynamic errors, stabilization systems, and tuning algorithms.

UK PubMed Central (United Kingdom)

A conserved multi-subunit complex (MybMuvB, MMB), regulates transcriptional activity of many different target genes in Drosophila somatic cells. A paralogous complex, tMAC, controls...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The behavior of air flows in complex heat exchanger passages is reviewed with a focus on the heat transfer effects of boundary-layer development, turbulence, spanwise and streamwise vortices, and wake management. Each of these flow features is discussed for the plain, wavy, and interrupted passages found in contemporary compact heat exchanger designs. Results from the literature are used to help explain the role of these mechanisms in heat transfer enhancement strategies.

International Nuclear Information System (INIS)

The prevailing severe shortage of animal feed in most of the developing countries could, to a considerable extent, be overcome through improved range management, which includes introduction of high yielding drought-resistant forage crops, development of adequate water conservation measures, and as far as possible growing annual forage crops on part of the vast areas of arable land currently left fallow each year. Year round measurements are essential for a good understanding of soil water and nutrients dynamics, which allow for adequate evaluation of pasture management alternatives. The methods most commonly used for moisture measurements in soil profiles are discussed because such measurements are likely to form an essential part of any investigation aimed at increasing animal feed production through the development of adequate pasture management practices. (author).

International Nuclear Information System (INIS)

An unprecedented mobilization at all levels is being established in order to fight against the effects of climate change and announcements are increasing each week with proposals of ever more ambitious plans of action. A new landscape is beginning to take shape from a more varied energy supply with less carbon. This new order highlights several central R/D areas which are to be developed and which re described in the first part of this article. How are these plans of action going to be put into practice in the field, within the dynamics of the great unifying project 'Grenoble University of Innovation'? How can the innovation process be speeded up to quickly find answers to all these questions? How can all scientific disciplines be incorporated in this run-up and how can the different players be brought to interact? The new PREDIS centre in Grenoble, described in the second part of the article, is intended to answer these ...

Energy Technology Data Exchange (ETDEWEB)

Interference between the crossover leg of the Reactor Coolant System(RCS) and the Pipe Whip Restraints(PWR) has brought a degradation issue of the integrity of the Reactor Coolant System in Westinghouse type Nuclear Power Plants(NPPs) of Korea. According to the gap inspection carried out during planned overhaul (year 2000), interference between the crossover leg and the PWR was found in each RCS loop. This plant has had the high vibration problem on the RC pump 'B'. The reason for the high vibration in the RC pump 'B' had been massively surveyed and it was found that the crossover leg of RCS contacted with the PWR in hot condition. Since the contact between the crossover leg and the PWR changes the dynamic characteristics of the piping system for the RCS, this is considered as one reason for the high vibration. And a possibility of overstress on the crossover leg due to the contact with the PWR should be evaluated. Through ...

International Nuclear Information System (INIS)

A good knowledge of medfly population dynamics is necessary to control it. Population dynamics are being studied by means of the Jackson trap with trimedlure attractant (male, sex-pheromone). Weekly sampling of wild medfly populations was started in June at Aabde and in August at Sour and Jbeil. Trap surveys of medfly density will be carried for at least one year before sterile males releases are started against a long-established infestation. Since populations can vary with season and in different parts of an infested area. Knowledge of this variation is needede to determine when releases should start, because they should begin, just after or during a population decline. Field evaluation will include, ecological data on medfly population distribution number, host preference, and medfly overwintering. Surveys of medfly adults and larvae, host species, and phenology, temperature and medfly history, all will be used to guide ...

Energy Technology Data Exchange (ETDEWEB)

A 4-loop Pressurised Water Reactor (PWR) primary coolant system has been analysed for the postulated Loss of Coolant Accident (LOCA) event in order to derive peak dynamic loads for qualifying the design of equipment supports and pipe whip restraints. Pipe whip restraints as well as pipe and equipment supports are nonlinear by nature because of the presence of gaps and the different directional stiffnesses arising from snubber, steelwork and geometric and material interaction at the concrete to steel embedment. The different structural idealisations for the supports and restraints have an influence on the dynamic response of the structure. In the first of the two part paper a range of idealisation models for the Steam Generator and Reactor Coolant Pump vertical columns ranging from elastic stiffnesses to bilinear stiffnesses with or without preload were examined. Due to both structural and loading complexity, the behaviour ...

Science.gov (United States)

We present and explain numerical results illustrating the mechanism of a type of discontinuous bifurcation of a chaotic set that occurs in typical dynamical systems. After the bifurcation, the chaotic set acquires new pieces located at a finite distance from its location just before the bifurcation, and these new pieces were not part of a previously existing chaotic set. A scaling law is given describing the creation of unstable periodic orbits following such a bifurcation. We also provide numerical evidence of such a bifurcation for a nonattracting chaotic set of the H{acute e}non map. {copyright} {ital 1998} {ital The American Physical Society}

Science.gov (United States)

Analysis of ENSO Dynamics and ThermoDynamics in the Western Pacific Warm Pool - An Application of Multi-Sensor Satellite Observations. ...

Energy Technology Data Exchange (ETDEWEB)

Large-eddy-simulations are performed for the heat transfer and the wake flow of a thin rotating disk subjected to an outer parallel passing stream of air. Above a critical value for the angular velocity of the disk, heat transfer augmentation sets on. This is strongly related to a flow instability that leads to a periodic vortex generation at the counter-moving disk side. The resulting phenomena are captured by the classical Landau model. For higher angular velocities the wake becomes fully turbulent, and here the transition to turbulence seems to be very abrupt. In this regime, a periodic vortex generation is observable at the co-moving disk side, too. (orig.) [German] Grobstruktur-Simulationen werden fuer die Waermeuebertragung und die Nachlaufstroemung fuer eine duenne rotierende Scheibe in einem aeusseren parallelen Luftstrom durchgefuehrt. Oberhalb eines kritischen Wertes fuer die Rotationsgeschwindigkeit setzt eine Verstaerkung der ...

International Nuclear Information System (INIS)

Magnetic excitation in coupled multispin system is studied theoretically focusing on Cu_2Fe_2Ge_4O_1_3 and Cu_2CdB_2O_6 as typical examples of such system. These compounds consist of spin dimer and spin monomer parts and show an antiferromagnetic phase transition at low temperatures due to the spin monomer part. A multispin containing a spin dimer and spin monomers is treated as a basis unit. The multispin forms a spin multiplet and its energy levels are separated into high and low regions reflecting the characteristic energies of the dimer and monomer parts. We regard the system as interacting multispins and apply an extended Holstein-Primakoff theory by introducing bosons for each energy level of a spin multiplet. In the low-energy region, the obtained magnon dispersion and dynamical spin correlation function agree quantitatively with experimental results of inelastic neutron scattering performed in ...

International Nuclear Information System (INIS)

This paper (paper I) presents the first part of results obtained with the PF-1000 facility for the first time at its upper energy limit (?1 MJ). Special attention is paid here to plasma ('pinch') dynamics, which was investigated in relation to its electro-technical and radiation (especially neutron) characteristics with the help of a number of diagnostics, both time-integrated and with nanosecond temporal resolution. In these methods we utilized a Rogowski coil for the routine electro-technical measurements, visual multi-frame and streak cameras, soft x-ray pin-hole multi-frame cameras, PIN-diode assembly and PM tubes with scintillators for soft and hard x-rays as well as for neutron investigations together with a set of activation counters. In particular, the temporal cross correlation of different phenomena taking place during the discharge was investigated. The pinch's longevity appears to be 10-15 times larger than the ideal ...

International Nuclear Information System (INIS)

Electron and ion beam dynamics of the PF-1000 facility were investigated for the first time at its upper energy limit (?1 MJ) in relation to neutron emission, the pinch's plasma ('target') characteristics and some other parameters with the help of a number of diagnostics with ns temporal resolution. Special attention was paid to the temporal and the spatial cross correlations of different phenomena. Results of these experiments are in favour of a neutron emission model based on ion beam-plasma interaction with three important features: (1) the plasma target is hot and confined during a few 'inertial confinement times'; (2) the ions of the main part of the beam are magnetized and entrapped around the pinch plasma target for a period longer than the characteristic time of the plasma inductive storage system and (3) ion-ion collisions (both fusion collisions, due to head-on impacts and Coulomb collisions) are responsible for neutron emission. ...

Energy Technology Data Exchange (ETDEWEB)

In this thesis a study is made of the of voltage characteristics and reactive power control in the transmission network of the Electric Power Systems (EPS) with static compensators of VARs (SCVs). The necessity of voltage and reactive power control and the application of SCVs as a solution means for three representative operation stages of the EPS, considering balanced operation conditions and fundamental frequency is analyzed: Operation in the presence of incremental voltage changes, quasi-stationary operation or steady state and behavior at the occurrence of big disturbances. The application of SCVs to systems of integral transmission is in general a closed loop control system, reason why the analysis of the interaction of the system EPS-SCV is considered as an essential part of the voltage and reactive power control study. Firstly, the response analysis of the control loop is made for incremental voltage changes, representing the power system by means of its ...

British Library Electronic Table of Contents (United Kingdom)

SummaryBackground Intracellular transport via processive kinesin, dynein, and myosin molecular motors plays an important role in maintaining cell structure and function. In many cases, cargoes move distances longer than expected for single motors; there is significant evidence that this increased travel is in part due to multiple motors working together to move the cargoes. Although we understand single motors experimentally and theoretically, our understanding of multiple motors working together is less developed. Results We theoretically investigate how multiple kinesin motors function. Our model includes stochastic fluctuations of each motor as it proceeds through its enzymatic cycle. Motors dynamically influence each other and function in the presence of thermal noise and viscosity. We...

International Nuclear Information System (INIS)

The results of radon concentration measurements inside of the Gabriel caves of Mexico, during three consecutive two-month periods covering almost three seasons, are reported in the present work. The radio-ecological importance of this site is related to the radon and its concentration-dynamic behavior in the cave. Further interest in radiation safety motivated this initiative since routine biological field work is done, with people spending long periods of time there. CR-39 passive nuclear track detector was chosen for this survey. Radon concentration levels decrease during the rainy season and show different values depending on the ventilation and geometeorological structure. Measured values range between 956 and 4931Bqm-3, an indication that radon doses may exceed the allowed values for workers. This project is part of a larger study of indoor radon alpha emitters in Mexican caves.

British Library Electronic Table of Contents (United Kingdom)

The use of natural gas in China is still relatively immature, as gas production only supplies a low percentage of the domestic energy system. In contrast, Chinese economy mainly relies on coal with a 67% share of the total primary energy supply. The environmental impact from this high coal dependence is significant and planners have sought for cleaner energy sources. Natural gas is both cleaner and generally more efficient than coal and gas consumption is rising quickly due to these facts. The growth tendency indicates that natural gas will become an important substitution for coal in some parts of the Chinese primary energy consumption. To quantify this tendency, this paper uses a system dynamics model to create a possible outlook. The results show that the gas consumption in China will c...

Energy Technology Data Exchange (ETDEWEB)

This report describes a simple seismic analysis model of the KALIMER-600 sodium cooled fast reactor and its application to the seismic time history analysis. To develop the simple seismic analysis model, the detailed 3-D finite element analyses for main components, IHTS piping system, and reactor building were carried out to verify the dynamic characteristics of each part of simple seismic analysis models. By using the developed simple model, the seismic time history analyses for both cases of a seismic isolation and non-isolation design of KALIMER-600 were performed. From the comparison of the calculated floor response spectrum, it is verified that the seismically isolated KALIMER-600 reactor building shows a great performance of a seismic isolation and assures a seismic integrity.

British Library Electronic Table of Contents (United Kingdom)

Vulcanian eruptions are common at many volcanoes around the world. Vulcanian activity occurs as either isolated sequences of eruptions or as precursors to sustained explosive events and is interpreted as clearing of shallow plugs from volcanic conduits. Breadcrust bombs characteristic of Vulcanian eruptions represent samples of different parts of these plugs and preserve information that can be used to infer parameters of pre-eruption magma ascent. The morphology and preserved volatile contents of breadcrust bombs erupted in 1999 from Guagua Pichincha volcano, Ecuador, thus allow us to constrain the physical processes responsible for Vulcanian eruption sequences of this volcano. Morphologically, breadcrust bombs differ in the thickness of glassy surface rinds and in the orientation and den...

British Library Electronic Table of Contents (United Kingdom)

The effect of various diallyl (diallyl ortho phthalate, diallyl terephthalate and diethylene glycol diallyl carbonate) and triallyl monomers (triallyl cyanurate and triallyl isocyanurate) on the processability of polyphenylene oxide (PPO) was studied. The solubility parameters of the monomers indicated that diallyl orthophalate, dially terephthalate and triallyl cyanurate should be miscible with PPO suggesting their applicability as reactive plasticizers to improve the processability of PPO. Rheological studies of 60:40 wt:wt PPO:allylic blends indicate that the addition of 40wt% of allylic monomers significantly improved processability - blends of 60PPO:40DEGDAC indicates the highest viscosity and the highest T"g. Rheological studies and dynamic mechanical analysis on various PPO/DAOP ble...

Energy Technology Data Exchange (ETDEWEB)

In the development of the man-made island siting technology of nuclear power plants, assessing the stability of the seawall against large ocean waves and earthquakes is indispensable. Concerning with the seismic stability of the seawall, prediction of the deformation like sliding and settlement of the seawall during earthquake including the armour units in front of the caisson becomes important factor. For this purpose, the authors have developed the two-dimensional DEM-FEM coupled analysis method (SEAWALL-2D) to predict the deformation of the seawall covered with the armour units during earthquake. In this method, movements of the armour units are calculated in DEM analysis part and deformation of the caisson, rubble moundsand seabed and back fill are calculated in FEM analysis part taking the nonlinearity of the soil materials based on the effective stress into account. Numerical simulations of dynamic centrifuge model ...

Environmental Research Database

ObjectivesTo obtain a benchmarked unsteady aerodynamic code for the S809 aerofoil; including Dynamic Stall. ~%~~%~The code will be that of Leishman & Beddoes suitably configured for the aerofoil's use on wind tubines. ~%~~%~To involve the international community during the assessment phase after benchmarking.~%~~%~To compare the data collected with that from the NWTC experiment.~%~~%~To improve the predictive capability of extant horizontal axis wind turbine performance codes. ~%~~%~To be compliant with b [continued...]DescriptionIn December 2000 the National Renewable Energy Laboratory (USA) held an international seminar to consider the predictive capabilities of w ind-turbine codes using their recently measured data. This highlighted the need for a detailed consideration of the codes sub-system with proper benc hmarking (became part of an ...

Energy Technology Data Exchange (ETDEWEB)

A new double-null, slotted divertor configuration will be installed for the DIII-D Radiative Divertor Program at General Atomics in late 1996. Four cryocondensation pumps, three new and one existing, will be part of this new divertor. The purpose of the pumps is to provide plasma density control and to limit the impurities entering the plasma core by providing pumping at each divertor strike point. The three new pumps are based on the design of the existing pump, installed in 1992 as part of the Advanced Divertor Program. The pump continues to operate successfully. The new pumps require geometry modifications to the original design. Therefore, extensive modal and dynamic analyses were performed to determine the behavior of these pumps and their helium and nitrogen feed lines during disruption events. Thermal and fluid analyses were also performed to characterize the helium two-phase flow regime in the pumps and their ...

International Nuclear Information System (INIS)

A new double-null, slotted divertor configuration will be installed for the DIII-D Radiative Divertor Program at General Atomics in late 1996. Four cryocondensation pumps, three new and one existing, will be part of this new divertor. The purpose of the pumps is to provide plasma density control and to limit the impurities entering the plasma core by providing pumping at each divertor strike point. The three new pumps are based on the design of the existing pump, installed in 1992 as part of the Advanced Divertor Program. The pump continues to operate successfully. The new pumps require geometry modifications to the original design. Therefore, extensive modal and dynamic analyses were performed to determine the behavior of these pumps and their helium and nitrogen feed lines during disruption events. Thermal and fluid analyses were also performed to characterize the helium two-phase flow regime in the pumps and their ...

Energy Technology Data Exchange (ETDEWEB)

Wind power is an increasingly significant renewable energy resource, producing no environmentally damaging C0{sub 2} emissions. The efficient production of electricity by wind turbines relies on aerodynamics: aerodynamics of wind turbines provides the fundamental solutions to efficient wind turbine design. Following a historical introduction, Part 1 of Aerodynamics of Wind Turbines is concerned with basic rotor aerodynamics, while Part 2 deals with structural aspects of the wind turbine and calculation of the loads on it. Topics covered include increasing mass flow through the turbine, performance at low and high wind speeds, assessment of the extreme conditions under which the turbine will perform and the theory for calculating the lifetime of the turbine. The classical Blade Element Momentum method is also covered, as are eigenmodes and the dynamic behaviour of a turbine. Aerodynamics of Wind Turbines is an essential ...

Science.gov (United States)

A unified Nonhydrostatic Multiscale Model on the Arakawa B grid (NMMB) designed for a broad range of spatial and temporal scales has been under development within the Earth System Modeling Framework (ESMF) at the National Centers for Environmental Prediction (NCEP) as a part of the new National Environmental Modeling System (NEMS). The model follows the general modeling philosophy of the NCEP's WRF NMM grid-point regional dynamical core. The model uses the regular latitude-longitude grid for the global domain, and a rotated latitude-longitude grid in regional applications. The nonhydrostatic component of the model dynamics is introduced through an add-on module that can be turned on or off depending on resolution. The "isotropic" quadratic conservative finite-volume horizontal differencing employed in the model conserves a variety of basic and derived dynamical and quadratic quantities and preserves ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of the project is to further develop a Danish natural gas reformer system including optimisation of subsystems and the overall system consisting of a natural gas reformer and fuel cell CHP generator. This will contribute to the evaluation of to what extend Denmark shall develop small reformer units for PEM fuel Cells. In the project a reformer system with a high degree of automatic control has been build that fulfils the CHP requirements to operation time, dynamics etc. This work, with a FP05 reformer unit, has given valuable results concerning the possibilities and limitations of the reformer technology for CHP usage. It is important that the reformer and fuel cell units are designed with matching yields to optimise efficiency, turn-down start-up time etc. The burner that delivers heat for the steam reaction shall be able to use natural gas as fuel. This gives the possibility of using existing burner technology. In addition this will improve the ...

Energy Technology Data Exchange (ETDEWEB)

The boundary-integral equation method is well suited for the calculation of the dynamic-stiffness matrix of foundations embedded in a layered visco-elastic halfspace (or a transmitting boundary of arbitrary shape), which represents an unbounded domain. It also allows pile groups to be analyzed, taking pile-soil-pile interaction into account. The discretization of this boundary-element method is restricted to the structure-soil interface. All trial functions satisfy exactly the field equations and the radiation condition at infinity. In the indirect boundary-element method distributed source loads of initially unknown intensities act on a source line located in the excavated part of the soil and are determined such that the prescribed boundary conditions on the structure-soil interface are satisfied in an average sense. In the two-dimensional case the variables are expanded in a Fourier integral in the wave number domain, while in three ...

DEFF Research Database (Denmark)

Udgivelsesdato: 2008

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

This report contains the study on the dynamic characteristics of Wolsung fuel rod and on the dynamic balancing of rotating machinery to evaluate the performance of nuclear reactor components. The study on the dynamic characteristics of Wolsung fuel rod wa...

Science.gov (United States)

Spontaneous radiation emitted from relativistic electrons undergoing betatron motion in a plasma-focusing channel is analyzed, and applications to plasma wake-field accelerator experiments and to the ion-channel laser (ICL) are discussed. Important similarities and differences between a free electron laser (FEL) and an ICL are delineated. It is shown that the frequency of spontaneous radiation is a strong function of the betatron strength parameter a(beta), which plays a role similar to that of the wiggler strength parameter in a conventional FEL. For a(beta) > or approximately 1, radiation is emitted in numerous harmonics. Furthermore, a(beta) is proportional to the amplitude of the betatron orbit, which varies for every electron in the beam. The radiation spectrum emitted from an electron beam is calculated by averaging the single-electron spectrum over the electron distribution. This leads to a frequency broadening of the radiation spectrum, which places ...

International Nuclear Information System (INIS)

A model for the simulation of the time dependent behavior and the analysis of the equilibrium of the coupled system of storage ring and Free Electron Laser (FEL) is presented. The analysis comprises both amplifier and oscillator FEL. Bunch lengthening and energy widening due to wake forces are taken into account in a self-consistent way. The method is based on a mapping algorithm for means and correlations of the electron distribution function, pioneered by K. Hirata. The evolution of the laser field in the oscillator FEL is described by K. Hirata. The evolution of the laser field in the oscillator FEL is described by supermodes. The model is used to simulate an FEL in a small 500 MeV storage ring with 100 m circumference. Typical values for the output power, spatial, and spectral characteristics of the emitted radiation are presented.

Energy Technology Data Exchange (ETDEWEB)

Applications, techniques, instrumentation, and interpretation of flow visualization are discussed. Methods of using flow visualization for the examination of combustion in furnaces, heat transfer with heat exchangers, and in fluid engines are explored, along with flow visualization in food processing, steel-casting, and process engineering. Further attention is given to pipe and channel flow, flow separation in laminar flow and around oscillating airfoils, wakes and vortices, supersonic flow and shock waves, and stratified flow and oceanography. The visualization of boundary layers is considered for various conditions, and applications for multiphase flow, rheology, and medical problems are detailed. Oil film, dry-surface coating, chemical, fluorescent, and minituft methods are presented, as well as the use of tracers, optical techniques, strobe lights, lasers, computerized data acquisition, and hot-wire anemometry.

British Library Electronic Table of Contents (United Kingdom)

Fatigue crack growth tests of three ferrite-pearlite steels with different size and spacing of pearlite particles, which were uniformly distributed in the ferrite matrix, were carried out to investigate the effect of microstructure on fatigue crack growth behavior in the Paris regime. The fatigue crack growth rates for the three materials did not coincide with each other, even when the crack growth curves were arranged by the effective stress intensity factor range. From in situ observations, crack tip stress shielding phenomena, such as interlocking and branching, were found on the crack wake, which enhanced fatigue crack growth resistance. A small size and spacing of pearlite particle seemed to induce small but frequent crack deflections, which resulted in crack closure phenomena. On the...

Norwegian Open Research Archives (NORA)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A method of assembling two or more parts together that may be metal, ceramic, metal and ceramic parts, or parts that have different CTE. Individual parts are formed and sintered from particles that leave a network of interconnecting porosity in each sintered part. The separate parts are assembled together and then a fill material is infiltrated into the assembled, sintered parts using a method such as capillary action, gravity, and/or pressure. The assembly is then cured to yield a bonded and fully or near-fully dense part that has the desired physical and mechanical properties for the part's intended purpose. Structural strength may be added to the parts by the inclusion of fibrous materials.

International Nuclear Information System (INIS)

Aerodynamic sound derived from bluff bodies can be considerably reduced by flow control. In this paper, the authors propose a new method in which porous material covers a body surface as one of the flow control methods. From wind tunnel tests on flows around a bare cylinder and a cylinder with porous material, it has been clarified that the application of porous materials is effective in reducing aerodynamic sound. Correlation between aerodynamic sound and aerodynamic force fluctuation, and a surface pressure distribution of cylinders are measured to investigate a mechanism of aerodynamic sound reduction. As a result, the correlation between aerodynamic sound and aerodynamic force fluctuation exists in the flow around the bare cylinder and disappears in the flow around the cylinder with porous material. Moreover, the aerodynamic force fluctuation of the cylinder with porous material is less than that of the bare cylinder. The surface pressure distribution of the cylinder with porous ...

Energy Technology Data Exchange (ETDEWEB)

The subject of this volume is remote sensing for environmental monitoring and resource management. This session is divided in eight parts. First part is on general topics, methodology and meteorology. Second part is on geology, environment and land cover. Third part is on disaster monitoring. Fourth part is on operational status of remote sensing. Fifth part is on coastal zones and inland waters. Sixth and seventh parts are on forestry and agriculture. Eighth part is on instrumentation and systems. (A.B.). refs., figs., tabs.

CERN Document Server

Integration by parts is used to reduce scalar Feynman integrals to master integrals.

Energy Technology Data Exchange (ETDEWEB)

A proton exchange membrane fuel cell (PEMFC) must maintain a balance between the hydration level required for efficient proton transfer and excess liquid water that can impede the flow of gases to the electrodes where the reactions take place. Therefore, it is critically important to understand the two-phase flow of liquid water combined with either the hydrogen (anode) or air (cathode) streams. In this paper, we describe the design of an in situ test apparatus that enables investigation of two-phase channel flow within PEMFCs, including the flow of water from the porous gas diffusion layer (GDL) into the channel gas flows; the flow of water within the bipolar plate channels themselves; and the dynamics of flow through multiple channels connected to common manifolds which maintain a uniform pressure differential across all possible flow paths. These two-phase flow effects have been studied at relatively low operating temperatures under steady-state conditions and ...

International Nuclear Information System (INIS)

We introduce a novel search technique that can identify trans-Neptunian objects in three to five exposures of a pointing within a single Hubble Space Telescope (HST) orbit. The process is fast enough to allow the discovery of candidates soon after the data are available. This allows sufficient time to schedule follow-up observations with HST within a month. We report the discovery of 14 slow-moving objects found within 50 of the ecliptic in archival data taken with the Wide Field Channel of the Advanced Camera for Surveys. The luminosity function of these objects is consistent with previous ground-based and space-based results. We show evidence that the size distribution of both high and low inclination populations is similar for objects smaller than 100 km, as expected from collisional evolution models, while their size distribution differs for brighter objects. We suggest that the two populations formed in different parts of the protoplanetary disk and after ...

Energy Technology Data Exchange (ETDEWEB)

Fast Test Reactor core internal and peripheral components were assessed for flow-induced vibrational characteristics under scaled and simulated prototype flow conditions in the Hydraulic Core Mockup as an integral part of the Fast Test Reactor Vibration Program. The Hydraulic Core Mockup was an 0.285 geometric scale model of the Fast Test Reactor internals designed to simulate prototype vibrational and hydraulic characteristics. Using water to simulate sodium coolant, vibrational characteristics were measured and determined for selected model components over the scaled flow range of 36 to 110%. Additionally, in-situ shaker tests were conducted on selected Hydraulic Core Mockup outlet plenum components to establish modal characteristics. Most components exhibited resonant response at all test flow rates; however, the measured dynamic response was neither abnormal nor anomalously flow-rate dependent, and the predicted prototype ...

Energy Technology Data Exchange (ETDEWEB)

The three-dimensional (3-D), multiphase, computational fluid dynamic (CFD) code FLUENT is used to simulated two-phase flow behaviour in a CANDU header manifold under low (natural circulation) flow conditions. This behaviour was previously inferred from experimental data. The CFD simulations reported here are being used to support these inferences and to obtain a better understanding of phase distribution in the header manifold. The simulations seem to show that the vapor-water mixture models in the FLUENT code do not capture properly phase separation in the header and proper phase branching at the header-feeder connections that have been observed in experiments at low flows. The simulations using discrete-phase model in FLUENT, which tracks the pathlines of the individual vapor bubbles in the water continuum phase, show interesting, complicated and, in some cases, unexpected bubble trajectories from the point of injection of the bubbles at a feeder connection to ...

CERN Document Server

From this vast subject, I will pick out and review three specific topics, namely the formation and evolution of bars, the formation of bulges, and the evolution during multiple major mergers. Bars form naturally in galactic discs. Their evolution is driven by the exchange of angular momentum within the galaxy. This is emitted mainly by near-resonant material in the inner disc (bar), and is absorbed by near-resonant material in the outer disc and in the halo. As a result of this, the bar becomes stronger and rotates slower. Bulges are not a homogeneous class of objects. Based on their formation history, one can distinguish three types. Classical bulges are mainly formed before the actual disc component, from collapses or mergers and the corresponding dissipative processes. Boxy/peanut bulges are parts of bars seen edge-on. Finally, disc-like bulges are formed by the inflow of material to the center due to bar torques. Major mergers bring strong and fast evolution ...

Science.gov (United States)

We have developed a transportable container based direct detection Doppler lidar based on the double-edge molecular technique. The pulsed solid state system was built at the University of Geneva. It was used to make range resolved measurements of the atmospheric wind field as part of the VALID campaign at the Observatoire de Haute Provence in Provence, France in July 1999. Comparison of our lidar wind measurements, which were analyzed without knowledge of the results of rawinsonde measurements made under the supervision of ESA, show good agreement with these rawinsondes. These are the first Doppler lidar field measurements made with an eyesafe direct detection molecular-based system at 355 nm and serve as a demonstrator for future spaceborne direct detection wind systems such as the Atmospheric Dynamics mission. Winds are an important contributor to sea surface temperature measurements made with the Tropical Rainfall Measuring Mission (TRMM) ...

Energy Technology Data Exchange (ETDEWEB)

Safety-technical factors related to spontaneous ignition and dust explosions of biomasses were investigated. Parametres of dust explosions and effect of inertisation on the maximum pressure (pmax) and the maximum rate of pressure rise (Kstmax) were studied at elevated initial pressure (1-9 bar). The level of inertisation required to prevent dust explosions totally was determined at different initial pressures. The sensitivity of fuels to spontaneous ignition and the effect of pressure on the sensitivity to and temperature of spontaneous ignition were studied on a pressurised dynamic self-ignition equipment. The effect of inertisation on the self-ignition temperature and alternatives of preventing spontaneous ignition by effective inertisation in the pressure ranges of 1 and 25 bar were investigated. As an example of application, results obtained with the laboratory test equipment were extrapolated to bin sizes used in practice. As a factor contributing to ...

Energy Technology Data Exchange (ETDEWEB)

Biomass and nutrient dynamics of black spruce seedlings during the hardening phase of the greenhouse rotation were examined after four pre-hardening fertilization regimes - conventional, constant-rate loading, exponential loading, and high exponential loading (delivering respectively 15, 40, 40 and 60 mg N seedling{sup -1}) - in order to assess nutrient dilution and steady-state nutrition. Although height growth of seedlings had virtually ceased during hardening, shoot biomass increased 99-142% and root biomass increased five- to tenfold depending on treatment. The biomass increase compromised steady-state nutrient status by diluting internal nutrient pools as nutrient supply was unable to keep up with growth. Soil nutrient levels were rapidly depleted during this period because of plant uptake and lack of fertilizer supplementation. Pre-hardening nutrient loading partly countered and delayed dilution effects, especially when applied ...

Energy Technology Data Exchange (ETDEWEB)

In the design of natural gas compressor stations, a check valve is a critical element which is commonly placed on the discharge side of the compressor to prevent reverse flow that can cause serious damage to the compressor itself and other components such as seals and bearings. One of the selection criteria of the check valve for this particular application is the valve flow characteristics in steady flow, and its dynamic characteristics in unsteady flow operation. With regards to steady flow valve characteristics, current models for the determination of the check valve open angle versus mean flow velocity are based on semi-empirical data obtained from water tests, which were found to deviate from measurements involving fluids of relatively higher compressibility. This paper presents results of steady flow testing of an NPS 4 swing-type check valve in air. Mean flow velocities versus disk angles were measured together with several local pressure measurements at the ...

International Nuclear Information System (INIS)

The most important factor in assessing radiologic risk is ensuring scientific means for evaluation of the radioactive release impact upon humans and organisms. To evaluate quantitatively this impact not only knowledge of radioactivity distribution in these dynamical systems is necessary but also understanding the transfer mechanisms between ecosystem components is needed. Thus a complete radioecologic study appear to be very complex and needs defining the source term, dynamic description of radionuclides behavior in the ecosystem, estimation of radiation doses in the major components of the ecosystem and finally the effects of radiation doses upon different parts of the systems. A diagram of the steps implied in evaluation of the effects due to radioactive effluent release in the environment is presented and discussed. The following steps are described: - identification of radioactive sources, as well as their input rate. ...

Energy Technology Data Exchange (ETDEWEB)

This paper investigates the dynamic recrystallization behavior of a directionally solidified (DS) nickel-base superalloy. The dynamic recrystallization occurs after the uncoated superalloy has been tested by tensile creep at elevated temperature for a long time. The dynamic recrystallization temperature is slightly lower than that of the static recrystallization. The dynamic recrystallization behavior of the DS superalloy below the static recrystallization temperature is mainly related to the high temperature oxidation and the free surface. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

The major part of the chapter 'Physical Properties' in concerned with, in addition to nuclear and atomic properties, the properties of the metal molybdenum. Due to the huge number of relevant papers, the present volume comprises only the first part of the metal properties, i.e. the crystallographic properties, the electronic structure, the lattice dynamics, and subsequently the mechanical and thermal properties. There are two small sections where the properties of the molecules, primarily Mo/sub 2/ and Mo/sub 6/, and of the vapor are described. The strength and some other mechanical properties have been frequently investigated to establish the change due to neutron irradiation, because this affects the durability of the fuel containers in nuclear reactors. For that purpose, changes in structure, texture, etc., due to irradiation had to be determined; the structural properties of nonirradiated samples also ...

Energy Technology Data Exchange (ETDEWEB)

Four HVDC (high voltage DC) {+-} 250kV submarine OF (oil-filled) cables are to be installed each capable of 1.4-million kW for one dipole channel and two returns for forwarding to Yura Switchyard a part of the power to be generated by a Tachibanawan coal-fired power plant to open in 2000. The first cable is now being laid. They are to cover a distance of 48km on the sea bottom, and their 190mm diameter is the largest in the world and this decreases the required number of cables for a reduction in the construction cost. The installation is executed by use of a dedicated cable laying ship loaded with cables. The ship is equipped with five thruster screws by adjusting which a cable is fed into the sea and laid on the bottom with high positional accuracy in all directions, and with a 10m-accurate DPS (Dynamic Positioning System) besides GPS (Global Positioning System). Operating on the sea bottom is a simultaneous laying/burying machine which ...

Energy Technology Data Exchange (ETDEWEB)

Mass shift of accelerated charges-sources of a massive vector and massive scalar fields, are considered in an approximation which is classical with respect to the charge motion but quantum with respect to their interaction with their proper field. For uniformly accelerated charges the mass shifts are expressed in terms of cylindrical functions of the quantum parameter ..mu..c/sup 3//h/2..pi..w/sub 0/ which is the ratio of the mass ..mu.. of the proper field quanta to the charge acceleration w/sub 0/. For finite positive values of the parameter both the imaginary and real parts of the shifts are nonvanishing and negative. For ..mu -->..0 the real part of the mass shift of a vector charge tends to the classical value -..cap alpha..h/2..pi..w/sub 0//2c/sup 3/ obtained earlier, thereas that of the scalar charge tends to zero. These and other properties of the shifts as functions of ..mu.. are studied by taking into account the locality of ...

International Nuclear Information System (INIS)

This paper proposes an integrated method for using experimental data and CFD modeling to develop engineering correlations for atrium smoke management. Part I focused on the experimental program and validation of a CFD model of the experimental facility. Part II describes the extension of this model to a parametric study of balcony spill plumes. Smoke management in buildings during fire events often uses mechanical ventilation systems to maintain smoke layer elevation above a safe evacuation path. Design of these systems requires accurate correlations for the smoke production or mass flow rate of the buoyant fire plume. One design issue is the mass flow rate of fire plumes which spill out from a fire compartment, under a balcony and up through an atrium or other large volume. Current engineering correlations for these balcony spill plumes (BSPs) are based on a combination of one-tenth scale test data and theoretical analysis. The suitability of ...

Energy Technology Data Exchange (ETDEWEB)

A study of the electron beam dynamics in the linac is conducted for the FERMI free electron laser (FEL) founded for construction at the Sincrotrone Trieste

UK PubMed Central (United Kingdom)

In this paper, we suggest that perception could be modeled by assuming that sensory input is generated by a hierarchy of attractors in a dynamic system. We describe a mathematical model which exploits...Full Text Available

UK PubMed Central (United Kingdom)

Fungal and oomycete populations and their dynamics were investigated following the introduction of the biocontrol agent Pythium oligandrum into the rhizosphere of tomato plants grown...Full Text Available

UK PubMed Central (United Kingdom)

Dynamic clamp is a powerful method that allows the introduction of artificial electrical components into target cells to simulate ionic conductances and synaptic inputs. This method is based...Full Text Available

Science.gov (United States)

... of the cycle shows that the separation area ea. ... with suitable flow solvers based on the Reynolds ... AGARD 75th Fluid Dynamics Panel Meeting and ...

International Nuclear Information System (INIS)

Velocity field behind a flat plate, placed near the wall in a narrow channel as a simulant of a BWR fuel spacer, was measured by using a hot wire anemometer. It was found that not only the positions where the dead water region behind flat plate disappeared but also the locations where the velocity relaxation completed were almost independent of the width of the clearance, although the local average velocity and velocity fluctuation immediately downstream the flat plate were affected by the difference in the clearance. The transverse flow diversions in the channel cross section were evaluated from the shape of the average velocity profile. The decrease of local flow rate near the channel wall, which may causes the drift flow behind a flat plate, was encouraged as the drag of clearance increased. Attempts have been made to measure spanwise velocity in the narrow channel. A spanwise velocity that occurred due to flow diversion was observed and its magnitude reached 14% of cross-sectional ...

Energy Technology Data Exchange (ETDEWEB)

Formulation is introduced for discretizing a boundary integral equation into an indirect boundary element method for the solution of 3-dimensional topographic problems. Yokoi and Takenaka propose an analytical solution-capable reference solution (solution for the half space elastic body with flat free surface) to problems of topographic response to seismic motion in a 2-dimensional in-plane field. That is to say, they propose a boundary integral equation capable of effectively suppressing the non-physical waves that emerge in the result of computation in the wake of the truncation of the discretized ground surface making use of the wave field in a semi-infinite elastic body with flat free surface. They apply the proposed boundary integral equation discretized into the indirect boundary element method to solve some examples, and succeed in proving its validity. In this report, the equation is expanded to deal with 3-dimensional topographic problems. A problem of a ...

International Nuclear Information System (INIS)

Most wind farms consist of horizontal axis wind turbines (HAWTs) due to the high power coefficient (mechanical power output divided by the power of the free-stream air through the turbine cross-sectional area) of an isolated turbine. However when in close proximity to neighboring turbines, HAWTs suffer from a reduced power coefficient. In contrast, previous research on vertical axis wind turbines (VAWTs) suggests that closely spaced VAWTs may experience only small decreases (or even increases) in an individual turbine's power coefficient when placed in close proximity to neighbors, thus yielding much higher power outputs for a given area of land. A potential flow model of inter-VAWT interactions is developed to investigate the effect of changes in VAWT spatial arrangement on the array performance coefficient, which compares the expected average power coefficient of turbines in an array to a spatially isolated turbine. A geometric arrangement based on the configuration of shed vortices ...

Science.gov (United States)

45 Public Welfare 3 2010-10-01 2010-10-01 false Appendix A to Part 611 A Appendix A to Part 611 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE...

Science.gov (United States)

... Part IV uses Missionaries and Cannibals problems to further explore internal problem solving and search. Part V uses Missionaries ...

Czech Academy of Sciences Repository

Full Text Available

DEFF Research Database (Denmark)

Udgivelsesdato: Spring

KoreaScience (Korea)

Full Text Available

CSIR Research Space (South Africa)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

This paper deals with dynamic study of co-generator system with derived dynamic models of generator, excitation system, and turbine/governor from field tests. Mainly this study concentrates on frequency control by under-frequency relay. We simulates dynamic study of co-generator system using EMTDC. (author). 4 refs., 13 figs., 4 tabs.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

CERN Document Server

In the present paper we prove moderate deviations for a Curie-Weiss model with external magnetic field generated by a dynamical system, as introduced by Dombry and Guillotin-Plantard. The results extend those already obtained in the case of a constant external field by Eichelsbacher and L\\"owe. The Curie-Weiss model with dynamic external field is related to the so called dynamic Z-random walks. We also prove a moderate deviation result for the dynamic Z-random walk, completing the list of limit theorems for this object.

Energy Technology Data Exchange (ETDEWEB)

In the year 1996 the spheres of competence of several DLR-Institutes working in the areas of fluid dynamics, reaction kinetics, combustion, numerical methods and laser measuring techniques have been brought together while contributing to the internal DLR project 'combustion chamber modelling (BKM)', in order to proceed with the computational simulation of combustion processes in combustion chambers of gas turbines. The main issue was the development of a research code for numerical simulation of fluid flow in real combustion chambers. Here the development of computational models of physical and chemical processes was emphasized, among other processes the formation of soot was treated. Moreover, a worldwide outstanding database of measured data for the purpose of code validation has been created within the framework of the BKM project using the laboratory facilities of the DLR, which are in Germany unique for the experimental investigation of the ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes a maintenance problem in a fusion power plant. The problem is to specify which life limited parts should be replaced when there is an opportunity. The objective is to minimize the cost rate of replacement parts and of maintenance actions while satisfying a power plant availability constraint. The maintenance policy is to look ahead and replace all parts that will reach their life limits within a time called a screen. Longer screens yield greater system availabilities because more parts are replaced prior to their life limits.

Science.gov (United States)

The paper examines science fiction literature as a product and part of the social consciousness of the modern capitalist world order. This world order is seen as emphasizing science, technology, movement, growth, urbanization, industrialization, complex organization, and progress. The document is organized into two sections. The first section reviews theories of the sociology of knowledge and discusses knowledge as a process of self-production and reproduction of society. Influential theorists include Hegel, Marx, Lukacs, Mannheim, Gramsci, Habermas, and Touraine. Touraine's (1977) dynamic conflict-based systematic theory of society is based on three concepts: historicity, which defines the instruments of society's self-production; the system of historical action which is the totality of social and cultural orientations, by means of which historicity exercises its control of historicity and the system of historical action. The second section ...

Energy Technology Data Exchange (ETDEWEB)

The pollution of the environment with toxic metals is a result of many human activities, such as mining and metallurgy, and the effects of these metals on the ecosystems are of large economic and public-healthsignificance. This paper presents the features and advantages of the unconventional removal method of heavy metals - biosorption - as a part of bioremediation. Bioremediation consists of a group of applications, which involve the detoxification of hazardous substances instead of transferring them from one medium to another, by means of microbes and plants. This process is characterized as less disruptive and can be often carried out on site, eliminating the need to transport the toxic materials to treatment sites. The biosorption (sorption of metallic ions from solutions by live or dried biomass) offers an alternative to the remediation of industrial effluents as well as the recovery of metals contained in other media. Biosorbents are prepared from naturally ...

Energy Technology Data Exchange (ETDEWEB)

After pioneering work in the 1980s, plasma-based ion implantation (PBII) and plasma-based ion implantation and deposition (PBIID) can now be considered mature technologies for surface modification and thin film deposition. This review starts by looking at the historical development and recalling the basic ideas of PBII. Advantages and disadvantages are compared to conventional ion beam implantation and physical vapor deposition for PBII and PBIID, respectively, followed by a summary of the physics of sheath dynamics, plasma and pulse specifications, plasma diagnostics, and process modeling. The review moves on to technology considerations for plasma sources and process reactors. PBII surface modification and PBIID coatings are applied in a wide range of situations. They include the by-now traditional tribological applications of reducing wear and corrosion through the formation of hard, tough, smooth, low-friction and chemically inert phases and coatings, e.g. for ...

Energy Technology Data Exchange (ETDEWEB)

In order to make it easy for the reader to see the specific research carried out and the progress made, the following report of progress is done by topic. Each item has a format layout of Topic, Investigators, Objective, Significance, and Description of Progress, followed at the end by the relevant references. As is clear from the topics listed, the emphasis of the GW nuclear theory group has been on the structure and electromagnetic interactions of few-body nuclei. Both low- and intermediate-energy electromagnetic disintegration of these nuclei is considered, including coherent photoproduction of {pi} mesons. When the excitation energy of the target nucleus is low, the aim has been to handle the continuum part of the theoretical work numerically with no approximations, that is, by means of full three- or four-body dynamics. When structure questions are the issue, numerically accurate calculations are always carried through, limited only by the ...

Energy Technology Data Exchange (ETDEWEB)

Developments made under this program will play a key role in underpinning the technology for producing EC devices. It is anticipated that the work begun during this period will continue to improve materials properties, and drive yields up and costs down, increase durability and make manufacture simpler and more cost effective. It is hoped that this will contribute to a successful and profitable industry, which will help reduce energy consumption and improve comfort for building occupants worldwide. The first major task involved improvements to the materials used in the process. The improvements made as a result of the work done during this project have contributed to the enhanced performance, including dynamic range, uniformity and electrical characteristics. Another major objective of the project was to develop technology to improve yield, reduce cost, and facilitate manufacturing of EC products. Improvements directly attributable to the work carried out as ...

Energy Technology Data Exchange (ETDEWEB)

This report summarises nearly 20 biosphere reports and gives a synthesis of the work performed within the SR-Site Biosphere project, i.e. the biosphere part of SR-Site. SR-Site Biosphere provides the main project with dose conversion factors (LDFs), given a unit release rate, for calculation of human doses under different release scenarios, and assesses if a potential release from the repository would have detrimental effects on the environment. The intention of this report is to give sufficient details for an overview of methods, results and major conclusions, with references to the biosphere reports where methods, data and results are presented and discussed in detail. The philosophy of the biosphere assessment was to make estimations of the radiological risk for humans and the environment as realistic as possible, based on the knowledge of present-day conditions at Forsmark and the past and expected future development of the site. This was achieved by using the ...

International Nuclear Information System (INIS)

This paper describes a long term course of research into the fundamentals of two phase flow regime dynamics that had lead to a differential description of regime properties. The development has included experiment, microscale simulation, and mathematical averaging to produce a dynamic equation for interfacial area.

UK PubMed Central (United Kingdom)

AbstractWe combined atomistic molecular-dynamics simulations with quantum-mechanical calculations to investigate the sequence dependence of the stretching behavior of duplex DNA. Our...Full Text Available

UK PubMed Central (United Kingdom)

Reliable characterization of locomotor dynamics of human walking is vital to understanding the neuromuscular control of human locomotion and disease diagnosis. However, the inherent oscillation and...Full Text Available

UK PubMed Central (United Kingdom)

Combined QM(PM3)/MM molecular dynamics simulations together with QM(DFT)/MM optimizations for key configurations have been performed to elucidate the enzymatic catalysis mechanism on the detoxification...Full Text Available

UK PubMed Central (United Kingdom)

Specific criteria have been developed based on computerized dynamic posturography (CDP) to assist clinicians in identifying patients with psychogenic balance problems (Cyr and Cevette, Full Text Available

UK PubMed Central (United Kingdom)

The percentages of total airflows over the nasal respiratory and olfactory epithelium of female rabbits were calculated from computational fluid dynamics (CFD) simulations of steady-state inhalation....Full Text Available

CERN Document Server

The methods of statistical dynamics are applied to a fluid with 5 conserved fields (the mass, the energy, and the three components of momentum) moving in a given external potential. When the potential is zero, we recover a previously derived system of parabolic differential equations, called "corrections to fluid dynamics".

UK PubMed Central (United Kingdom)

We studied the dynamics of microbial communities attached to model aggregates (4-mm-diameter agar spheres) and the component processes of colonization, detachment, growth, and grazing mortality. Agar...Full Text Available

UK PubMed Central (United Kingdom)

The passage of a vascular-injected paramagnetic contrast reagent (CR) bolus through a region-of-interest affects tissue ¹H₂O relaxation and thus MR image intensity. For longitudinal...Full Text Available

UK PubMed Central (United Kingdom)

We discuss the relationship between the dynamically changing tension gradients required to move water rapidly through the xylem conduits of plants and the proportion of conduits lost through embolism...Full Text Available

Science.gov (United States)

processes, we construct a stochastic dynamic model for air- craft counts in ... Also , queueing models for the arrival of aircraft at ... A queueing model has also been used to study ...... Assignment and Aircraft-Sequencing Algorithms in Terminal ...

UK PubMed Central (United Kingdom)

BackgroundAdhesive Capsulitis (AC) affects patient of all ages, and stretching protocols are commonly prescribed for this condition. Dynamic splinting has been shown effective in...Full Text Available

Science.gov (United States)

... Tunable semiconductor lasers are essential components for links employing optical frequency modulation (OFM) for enhanced dynamic range or ...

Science.gov (United States)

Wikileaks was inevitable. The Dynamics of. Information. Take advantage of the eddy currents. You can't step in the same river ...

Science.gov (United States)

... Dynamics Panel Executive AGARD 7 rue ... 4 AXIAL FLOW IN CORNERS AT SUPERSONIC ... AND HYPERSONIC FLOWS INCLUDING SEPARATION ...

British Library Electronic Table of Contents (United Kingdom)

This article presents a decentralized control scheme for the complex problem of simultaneous position and internal force control in cooperative multiple manipulator systems. The proposed controller is composed of a sliding mode control term and a force robustifying term to simultaneously control the payloads position/orientation as well as the internal forces induced in the system. This is accomplished independently of the manipulators dynamics. Unlike most controllers that do not require prior knowledge of the manipulators dynamics, the suggested controller does not use fuzzy logic inferencing and is computationally inexpensive. Using a Lyapunov stability approach, the controller is proven to be robust in the face of varying systems dynamics. The payloads position/orientation and the inte...

Energy Technology Data Exchange (ETDEWEB)

The microstructures of magnesium AZ31 are examined following hot compression testing and annealing. The grain size, fraction dynamically recrystallized and, in a couple of cases, the crystallographic texture are reported. It was found that the progress of dynamic recrystallization is strongly sensitive to processing conditions but that the dynamically recrystallized grain size was less sensitive to stress than in other metals. It was also found that, for structures containing between 80 and 95% dynamic recrystallization, abnormal grain growth occurs during annealing. The crystallographic texture produced is also sensitive to the deformation conditions. (orig.)

KoreaScience (Korea)

Full Text Available

CERN Document Server

Full-Potential Electronic Structure Method

DEFF Research Database (Denmark)

Udgivelsesdato: 2008-Sep

Science.gov (United States)

... measurement. Power spectral density measurements are made by the dynamic signal analyzer for each channel. A cross power ...

Science.gov (United States)

Page 1. Adaptive system and method for responding to computer network security attacks Abstract A dynamic network security ...

CERN Document Server

Industrial-process control valves Part2 : Flow capacity Section Four : Inherent flow characteristics and rangeability

Energy Technology Data Exchange (ETDEWEB)

There are two types in quench distortion of steel parts: thermal distortion and transformation distortion. Quench distortion is caused mainly by uneven cooling rate of steel parts from Austenitising temperature. The rapid cooled side is lengthened (convex deformation); the slow cooled side is shortened (concave deformation). So, to control the quench distortion, it is necessary to regulate the cooling rate of steel parts during quenching. TWO COMPONENTS produce the quench distortion of steel parts: the thermal stress and transformation stress. Generally, the effect of the thermal stress on the quench distortion is stronger than the transformation stress. The quench distortion is caused by uneven cooling rate of the steel parts, from Austenitising temperature to Ms point and Ms-Mf range. So, to control the quench distortion, it is very important to regulate the cooling rate of the ...

Energy Technology Data Exchange (ETDEWEB)

Goal was developing optical methods for study of dynamic processes at the electrode/electrolyte interface. In the past year, optical second harmonic generation was used for time-resolved measurements of thallium deposition on Cu(111). The studies of carrier dynamics in photo-excited materials have involved both steady-state and picosecond time-resolved luminescence measurements following photoexcitation of the semiconductor material.

International Nuclear Information System (INIS)

Dynamical models are presented that start with interstellar gas in an initial diffuse state and consider their gravitational collapse and the formation of dense cores. Frozen-in tangled magnetic fields are included to mimic forces that might oppose gravitational contraction and whose effectiveness may increase with increasing core densities. Results suggest the possibility that dense cloud cores may be dynamically evolving ephemeral objects, such that their lifespan at a given core density decreases as that density increases. 66 refs.

Energy Technology Data Exchange (ETDEWEB)

The mainly instationary operation of a solar heated receiver can be simulated with sufficient accuracy only if data about the dynamic behavior are available. For this reason, the dynamic behavior of a solar cavity receiver with parabolic dish collector is investigated. The development of a mathematical simulation considering heat transfer and storage processes is presented and the procedure for a numerical solution is illustrated. The performance of the calculation method is finally demonstrated by simulating the passage of a cloud.

Science.gov (United States)

This paper deals with the experimental identification and the validation of a non-parametric probabilistic approach allowing model uncertainties and data uncertainties to be taken into account in the numerical model developed to predict low- and medium-frequency dynamics of structures. The analysis is performed for a composite sandwich panel representing a complex dynamical system which is sufficiently simple to be completely described and which exhibits, not only data uncertainties, but above all model uncertainties. The dynamical identification is experimentally performed for eight panels. The experimental frequency response functions are used to identify the non-parametric probabilistic approach of model uncertainties. The prediction of the low- and medium-frequency dynamical responses obtained with the stochastic system is compared with the experimental measurements.

International Nuclear Information System (INIS)

The purpose of this study was to evaluate the usefulness of dynamic MRI for femoral head perfusion. Objects were 64 femoral heads of 44 normal cases (20-95 years old), 10 cases (33-90 y) of femoral neck fracture and 8 cases (61-86 y) using steroid due to articular rheumatism, nephrosis and other diseases. Siemens 1.0 T Magneton Impact with body array coil was used for dynamic MRI by the fast low-angle shot 2D method for every 17 sec interval. Gd-DTPA was injected intravenously. ROI was defined in the center of femur head and of trochanter to monitor their values for the dynamic curve. Evaluation was done on the ratio of enhancement ratio (ER) in the head/trochanter and on the curve in both heads. In normal cases, the head ER was significantly lower in >60 years old cases. There was neither significant correlation between their head/trochanter ER ratios nor significant difference between their dynamic ...

Energy Technology Data Exchange (ETDEWEB)

Planning for quality assurance (QA) in research and development (R D) is like stealing eggs without waking up the chickens. The QA program should be as unobtrusive as possible. Researchers require a QA program that affords them an environment capable of supporting repeatable experiments with accurate data without unduly stifling their creative abilities. Careful advance planning ensures that the intensity of control provided by quality-related systems is commensurate with the importance and scope of the activities being performed. Good scientific practices applied to small bench-scale projects may require minimal additional controls. As projects increase in size and complexity the controls imposed through planning must, by necessity, be increased. Research and development QA planning, just like any other planning, involves all affected individuals. The application of control systems is determined by factors such as customer or sponsor requirements, the importance ...

Energy Technology Data Exchange (ETDEWEB)

In recent years the 'Nowcasting Wake Vortex Impact Variables' model NOWVIV has been developed at the Deutsches Zentrum fuer Luft- und Raumfahrt, DLR, to forecast weather parameters in airport environments. The German Meteorological Service, DWD, employs his COSMO-DE model (COnsortium for Small scale Modelling-DEutschland) for operational forecasts in Germany. A systematic comparison of model output from NOWVIV and a derivate of COSMO-DE, named COSMO-FRA, is presented. Both models are centred at Frankfurt Airport with horizontal resolutions of 2.1 km and 2.8 km, respectively. In the DLR Project Wetter and Fliegen the COSMO-FRA model will replace the NOWVIV model and become a key component in the future rapid update cycle for adverse weather predictions at the airports of Frankfurt and Munich. The forecast vertical profiles of runway crosswind, head/tail wind, temperature, and turbulent kinetic energy (TKE) are validated against Wind and Temperature ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This device has and head-race pipe with an external part and a coaxial inner part. A measuring head is mounted movable between these 2 parts and has at least a thermocouple and a mobile grid for varying the section and the sodium flow to facilitate the impurities dissolution. This ensemble is completed by a longitudinal body containing the main parts of the indicator and surrounded by a thermal exchanger to cool the sodium.

Energy Technology Data Exchange (ETDEWEB)

A fuel injector comprises first and second housing parts, the first housing part being located within a bore or recess formed in the second housing part, the housing parts defining therebetween an inlet chamber, a delivery chamber axially spaced from the inlet chamber, and a filtration flow path interconnecting the inlet and delivery chambers to remove particulate contaminants from the flow of fuel therebetween.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

PMID:12324492

Energy Technology Data Exchange (ETDEWEB)

The presentation gives a brief insight on possibility of using the VEERA facility in studying the stratification phenomenon. The idea for such experiments is to use the facility upper plenum part to simulate the conditions in upper part of horizontal steam generator hot collector. The upper part of steam generator hot collector is one of the locations where the stratification can take part during natural circulation mode. 4 refs.

Energy Technology Data Exchange (ETDEWEB)

In a turbine rotor, a thermal mismatch between various component parts of the rotor occurs particularly during transient operations such as shutdown and startup. A thermal medium flows past and heats or cools one part of the turbine which may have a deleterious thermal mismatch with another part. By passively controlling the flow of cooling medium past the one part in response to relative movement of thermally responsive parts of the turbine, the flow of thermal medium along the flow path can be regulated to increase or reduce the flow, thereby to regulate the temperature of the one part to maintain the thermal mismatch within predetermined limits.

Energy Technology Data Exchange (ETDEWEB)

Convective cooling of turbine hot parts using a closed loop system is disclosed. Preferably, the present invention is applied to cooling the hot parts of combustion turbine power plants, and the cooling provided permits an increase in the inlet temperature and the concomitant benefits of increased efficiency and output. In preferred embodiments, methods and apparatus are disclosed wherein air is removed from the combustion turbine compressor and delivered to passages internal to one or more of a combustor and turbine hot parts. The air cools the combustor and turbine hot parts via convection and heat is transferred through the surfaces of the combustor and turbine hot parts.

Science.gov (United States)

A general relativistic model for the formation and acceleration of lowmass-loaded jets from systems containing accreting black holes is presented. The model is based on previous numerical results and theoretical studies in the Newtonian regime, but modified to include the effects of space-time curvature in the vicinity of the event horizon of a spinning black hole. It is argued that the boundary layer between the Keplerian accretion disk and the event horizon is best suited for the formation and acceleration of the accretion-powered jets in active galactic nuclei and micro-quasars. The model presented here is based on matching the solutions of three different regions: i- a weakly magnetized Keplerian accretion disk in the outer part, where the transport of angular momentum is mediated through the magentorotational instability, ii- a strongly magnetized, advection-dominated and turbulent-free boundary layer (BL) between the outer cold accretion disk and the event ...

Energy Technology Data Exchange (ETDEWEB)

The inner part of a fusion reactor will have to operate at very high neutron loads. In steady-state reactors the minimum fluence before the scheduled replacement of the reactor core should be at least l0-15 Mw.yr/m². A more frequent replacement of the core is hardly compatible with economic constraints. A most recent summary of the discussions of these issues is presented in Ref. [l]. If and when times come to build a commercial fusion reactor, the availability of information on the behavior of materials and components at such fluences will become mandatory for making a final decision. This makes it necessary an early development and construction of a neutron source for fusion material and component testing. In this paper, we present information on one very attractive concept of such a source: a source based on a so called Gas Dynamic Trap. This neutron source was proposed in the mid 1980s (Ref. [2]; see also a survey [3] ...

Energy Technology Data Exchange (ETDEWEB)

This study presents a dynamic analysis of a rotor supported by two turbulent flow model journal bearings and lubricated with couple stress fluid under nonlinear suspension. The dynamics of the rotor center and bearing center is studied. The dynamic equations are solved using the Runge-Kutta method. The analysis methods employed in this study is inclusive of the dynamic trajectories of the rotor center and bearing center, power spectra, Poincare maps and bifurcation diagrams. The maximum Lyapunov exponent analysis is also used to identify the onset of chaotic motion. The results show that the values of dimensionless parameters l* strongly influence dynamic motions of bearing and rotor centre. It is found that couple stress fluid improve the stability of the system when l* > 0.4 even if the flow of this system is turbulent. We also demonstrated that the dimensionless rotational ...

International Nuclear Information System (INIS)

To systematically analyze the dynamical implications of the matter content in cosmology, we generalize earlier dynamical systems approaches so that perfect fluids with a general barotropic equation of state can be treated. We focus on locally rotationally symmetric Bianchi type IX and Kantowski-Sachs orthogonal perfect fluid models, since such models exhibit a particularly rich dynamical structure and also illustrate typical features of more general cases. For these models, we recast Einstein's field equations into a regular system on a compact state space, which is the basis for our analysis. We prove that models expand from a singularity and recollapse to a singularity when the perfect fluid satisfies the strong energy condition. When the matter source admits Einstein's static model, we present a comprehensive dynamical description, which includes the qualitative asymptotic behavior, of models in the ...

Energy Technology Data Exchange (ETDEWEB)

This safety design guide for pipe rupture protection identifies high-energy systems in which pipe ruptures must be postulated to occur, as well as systems that must be protected from the dynamic effects of such ruptures. Dynamic effects considered in this SDG consist of pipe whip (including missiles generated by pipe ruptures, if any) and jet impingement, Requirements for protection against the dynamic effects of a postulated pipe rupture and method of protection of essential structures, systems and components are specified for these effects. The change status for the regulatory requirements, code and standards should be traced and this safety design guide shall be updated accordingly. 2 tabs., 5 refs. (Author) .new.

Science.gov (United States)

This investigation concerns the nonlinear dynamics of heat transfer from a surface using an upstream eddy promoter. A numerical model is developed for the coupled fluid flow and heat transfer process based on a modified MacCormack scheme. Numerical simulations are carried out to determine the response and heat transfer enhancement due to the promoter. The average heat transfer from a cavity floor is seen to be increased by a factor of approximately five over the unpromoted'' flow. Another interesting feature of the study is the nonlinear viscous flow dynamics from the cylinder-wall interaction which differ significantly from the familiar cylinder-free stream patterns.

Energy Technology Data Exchange (ETDEWEB)

The centroid and envelope dynamics of a high-intensity charged particle beam are investigated as a beam smoothing technique to achieve uniform illumination over a suitably chosen region of the target for applications to ion-beam-driven high energy density physics and heavy ion fusion. The motion of the beam centroid projected onto the target follows a smooth pattern to achieve the desired illumination, for improved stability properties during the beam-target interaction. The centroid dynamics is controlled by an oscillating "wobbler", a set of electrically-biased plates driven by RF voltage. __________________________________________________

Science.gov (United States)

In the present work we introduce a novel multi-agent model with the aim to reproduce the dynamics of a double auction market at microscopic time scale through a faithful simulation of the matching mechanics in the limit order book. The agents follow a noise decision making process where their actions are related to a stochastic variable, the market sentiment, which we define as a mixture of public and private information. The model, despite making just few basic assumptions over the trading strategies of the agents, is able to reproduce several empirical features of the high-frequency dynamics of the market microstructure not only related to the price movements but also to the deposition of the orders in the book.

Science.gov (United States)

... Each beam finite element was derived using Hamilton's principle and the following basic assumptions: the beam has an arbitrary amount of pretwist ...

British Library Electronic Table of Contents (United Kingdom)

The ultrafast dynamics of the DNA fluorescent dye Sybr Green I (SG) has been studied in buffer, single-stranded (ssDNA), double-stranded (dsDNA) and triple-stranded DNA (tsDNA). The fluorescence quantum yield of SG increases dramatically when bound to DNA (including tsDNA). The fluorescence dynamics of the free SG has shown two decay components with 0.15-0.4ps and 1.3-2.1ps time constants, depending on the fluorescence wavelength. Upon binding to DNA, the dynamics becomes slower exhibiting four decay components. This is mainly due to the restriction of the internal motions of the dye caused by the relatively rigid environment of the dye complexed with DNA.

UK PubMed Central (United Kingdom)

Humans, like other animals, are exposed to a continuous stream of signals, which are dynamic, multimodal, extended, and time varying in nature. This complex input space must be transduced and sampled...Full Text Available

UK PubMed Central (United Kingdom)

Axon outgrowth and guidance to the proper target requires the coordination of filamentous (F)-actin and microtubules (MTs), the dynamic cytoskeletal polymers that promote shape change and locomotion....Full Text Available

Science.gov (United States)

The H-Coal ebullated bed reactor contains at least four discrete components: gas, liquid, catalyst, and unconverted coal and ash. Because of the complexity created by these four components, it is desirable to understand the fluid dynamics of the system. The objective of this program is to establish the dependence of the ebullated bed fluid dynamics on process parameters. This will permit improved control of the ebullated bed reactor. Progress has been made in the study undertaken for defining the hydrodynamic properties of gas/liquid/solid systems as related to the H-Coal process. The literature search was completed, and a report will be issued shortly. Design and construction of the fluid dynamics unit proceeded as planned. Unit completion is scheduled for May 1, 1978.

UK PubMed Central (United Kingdom)

Species invasions are a principal component of global change, causing large losses in biodiversity as well as economic damage. Invasion theory attempts to understand and predict invasion success and...Full Text Available

CERN Document Server

Today, component oriented middlewares are used to design, develop and deploy easily distributed applications, by ensuring the heterogeneity, interoperability, and reuse of the software modules, and the separation between the business code encapsulated in the components and the system code managed by the containers. Several standards answer this definition such as: CCM (CORBA Component Model), EJB (Enterprise Java Beans) and .Net. However these standards offer a limited and fixed number of system services, removing any possibility to add system services or to reconfigure dynamically the middleware. Our works propose mechanisms to add and to adapt dynamically the system services, based on a reconfiguration language which is dynamically adaptable to the need of the reconfiguration, and on a tool of dynamic reconfiguration, a prototype was achieved for the OpenCCM platform, that is an implementation of the ...

International Nuclear Information System (INIS)

Real-time neutron radiography (RTNR) is now proving to be a valuable research tool in the study of hydrogenous fluid flow. One of the most significant advantages of neutron radiography is the ability to image hydrogenous substances (such as lubricants, coolants, and fuels) inside metallic materials such as aluminum and titanium engines. By using RTNR, one can then study dynamic events such as the movement of liquids inside these solids. The Phoenix Memorial Laboratory (PML) at the University of Michigan has recently developed and installed a facility dedicated to RTNR. The work at PML has shown that RTNR of dynamic events can provide information enabling the researcher to follow dynamic events that were previously impossible or impractical. This paper will show the variety of uses of RTNR presently being pursued at PML.

International Nuclear Information System (INIS)

... Union (INTAS), Brussels (Belgium) Science and Technology Center in Unkraine,

CERN Document Server

A recurrent idea in the study of complex systems is that optimal information processing is to be found near bifurcation points or phase transitions. However, this heuristic hypothesis has few (if any) concrete realizations where a standard and biologically relevant quantity is optimized at criticality. Here we give a clear example of such a phenomenon: a network of excitable elements has its sensitivity and dynamic range maximized at the critical point of a non-equilibrium phase transition. Our results are compatible with the essential role of gap junctions in olfactory glomeruli and retinal ganglionar cell output. Synchronization and global oscillations also appear in the network dynamics. We propose that the main functional role of electrical coupling is to provide an enhancement of dynamic range, therefore allowing the coding of information spanning several orders of magnitude. The mechanism could provide a microscopic ...

Science.gov (United States)

By H. J. Grover, TV.S. Hyler, Paul Kuhn, Charles B. Landers, and ...... E. Watkins. The Effects on Dynamic Lateral Stability and Control of ...

CERN Document Server

In this paper we present a complete solution to the problem of multifractal analysis of multiple ergodic averages in the case of symbolic dynamics for functions of two variables depending on the first coordinate.

Science.gov (United States)

Coral are symbiotic with photosynthetic dinoflagellates from the genus Symbiodinium. There are eight divergent clades (A-H) within the genus which each ... ...

Science.gov (United States)

... WHS- Washington Headquarters Service. ... The dynamic Joint Special Operations Task Force -- Philippines (JSOTF-P) has evolved and ...

UK PubMed Central (United Kingdom)

Quantitative microscopy has been extensively used in biomedical research and has provided significant insights into structure and dynamics at the cell and tissue level. The entire procedure...Full Text Available

Science.gov (United States)

... non- emissive guidance and collision alert, automated transport in dynamic environments, and assembly and inspection. Foveal Vision, Autonomous Agents, ...

UK PubMed Central (United Kingdom)

This article discusses three largely unrecognized aspects related to fluid movement in ocular tissues; namely, a) the dynamic changes in water permeability observed in corneal and conjunctival...Full Text Available

Science.gov (United States)

... i3a TYPT OF REPORT 13b TIME COVERED 14 DATE OF RF ... automation system when used in conjunction with other standard security measures. ...

Science.gov (United States)

... Information behavior in dynamic group work contexts: interwoven situational awareness, dense social networks and contested collaboration in ...

Science.gov (United States)

Wildlife Refuge, CA Rare and endangered endemic plants Diana Anderson Northern Arizona University Geomorphology Kathryn Thomas USGS, Flagstaff, AZ Vegetation dynamics John...

Science.gov (United States)

dust measured in the Arabian Gulf region during UAE2 and examine the hypothesis that ... [8] UAE2 took place in the southern Arabian Gulf region in August and ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the structure of dynamic neuronal ensembles (DNEs). DNEs represent a new paradigm for learning, based on biological neural networks that use variable structures. We present a computational neural element that demonstrates biological neuron functionality such as neurotransmitter feedback absolute refractory period and multiple output potentials. More specifically, we will develop a network of neural elements that have the ability to dynamically strengthen, weaken, add and remove interconnections. We demonstrate that the DNE is capable of performing dynamic modifications to neuron connections and exhibiting biological neuron functionality. In addition to its applications for learning, DNEs provide an excellent environment for testing and analysis of biological neural systems. An example of habituation and hyper-sensitization in biological systems, using a neural circuit from a snail is presented and ...

Science.gov (United States)

... defense's weapons are Space-based kinetic-kill vehicles ... I ti I obtained by dividing the weapons as ... of the optimal weapon-arge assigntments and ...

UK PubMed Central (United Kingdom)

Advances in modern neuroscience require the identification of principles that connect different levels of experimental analysis, from molecular mechanisms to explanations of cellular functions,...Full Text Available

UK PubMed Central (United Kingdom)

ObjectiveTo determine whether accounting for the time dynamics of diabetes exposure will change the risk estimates for colorectal cancer.Full Text Available

Science.gov (United States)

... 4 maximum aggregate size. The effects of strain rate (up to 2.5 in./in./sec) on ultimate compressive strength were obtained. ...

British Library Electronic Table of Contents (United Kingdom)

Experimental results of quasi-static and dynamic fracture of particle-filled polymer composite (PFPCM) "ALTUGLAS EI CH25" with a matrix of polymethylmethacrylate (PMMA) are reported in this paper. PMMA matrix is filled with rubber particles, as result a shock-resistant transparent composite is produced. The main task was to investigate experimentally and theoretically the fracture toughness of this composite under static and dynamic loading. A high-rate loading has been created by impulse magnetic field. Analysis of fracture process and its relation with the load parameters and material microstructure have been established. Application of the original testing method enabled determination of fracture toughness at very short loading times and comparison of the results with material dynamic p...

UK PubMed Central (United Kingdom)

Human languages evolve continuously, and a puzzling problem is how to reconcile the apparent robustness of most of the deep linguistic structures we use with the evidence that they undergo possibly...Full Text Available

Science.gov (United States)

freeston@alexandria.sdc.ucsb.edu tel: 805-893-8589 fax: 805-893-3045. _. ,' .;_. .'_. Abstract. There has been no fundamental change in the dynamic indexing ...