The paper investigates the effect of the wall heat flux ratio on the local heat transfer augmentation in a square channel with two opposite in-line ribbed walls for Reynolds numbers from 15,000 to 80,000. The square channel composed of 10 isolated copper sections has a length-to-hydraulic diameter ratio of 20. The rib height-to-hydraulic diameter ratio is 0.0625 and the rib pitch-to-height ratio equals 10. Six ribbed side to smooth side wall heat flux ratios are studied for four rib orientations. The results show that the ribbed side wall heat transfer augmentation increases with increasing ribbed side to smooth side wall heat flux ratios, but the reverse is true for the smooth side wall heat transfer augmentation. The average heat transfer augmentation of the ribbed side and smooth side wall decreases slightly with ...
1992-10-01
Chemical effects on L_#gamma#_1/L_#beta#_1 x-ray intensity ratio of molybdenum compounds
International Nuclear Information System (INIS)
Chemical effects on the intensity ratio of LX-ray of molybdenum compounds irradiated by 11-keV electrons and by 3-MeV protons were studied using an x-ray crystal spectrometer. It was found that the intensity ratios of L_#gamma#_1/L_#beta#_1 markedly decrease with the increase of ionicity of molybdenum compounds, except for the case of metallic molybdenum. (author).
1987-06-01
Energy Technology Data Exchange (ETDEWEB)
The improvement of startability achieved by chemical ignition promotion at low temperature was studied theoretically and experimentally in terms of compression ratio and cetane number using a small direct injection diesel engine. The findings are as follows: The compression ratio and cetane number vary almost linearly. When the compression ratio increases by 1, the cetane number decreases by about 9. Since almost the same ignition condition at starting can be achieved by adjusting the number of cranking cycles, there is almost no influence of compression ratio and cetane number on ignition delay. When the soak temperature is -10{sup 0}C and the compression ratio is 18, the influence of the cetane number is almost negligible. Given the same starting time, the influence produced by an increase in compression ratio by 1 is ...
1988-11-25
Chemical effects of L X-ray intensity ratios in niobium and molybdenum compounds
Energy Technology Data Exchange (ETDEWEB)
Chemical effects of L X-ray intensity ratios in niobium and molybdenum compounds were studied by electron and proton bombardments. L{sub {gamma}1} X-rays which involve transition of 4d electrons of the valence shell were found to be sensitive to the chemical environment. The L{sub {gamma}1}/L{sub {beta}1} X-ray intensity ratio increased with an increase of the 4d electron occupation of niobium or molybdenum in niobium or molybdenum compounds, showing that the chemical effects can be ascribed to the 4d electron behavior of the metallic atom in its compounds. (orig.).
1990-12-20
Chemical effects of L X-ray intensity ratios in niobium and molybdenum compounds
International Nuclear Information System (INIS)
Chemical effects of L X-ray intensity ratios in niobium and molybdenum compounds were studied by electron and proton bombardments. L_#gamma#_1 X-rays which involve transition of 4d electrons of the valence shell were found to be sensitive to the chemical environment. The L_#gamma#_1/L_#beta#_1 X-ray intensity ratio increased with an increase of the 4d electron occupation of niobium or molybdenum in niobium or molybdenum compounds, showing that the chemical effects can be ascribed to the 4d electron behavior of the metallic atom in its compounds. (orig.).
1990-12-01
International Nuclear Information System (INIS)
In a cold fusion method by electrolysis, a hydrogen occluding material mainly comprising vanadium is used as a material for a negative electrode, and lithium isotopes are incorporated in the material by more than 93%. That is, the ratio of lithium 7 ("7Li) isotope is increased to higher than the natural existent ratio, so that tritium ("3H) concentration in the hydrogen occluding material can be increased, to attain energy at high efficiency. (T.M.).
1993-03-02
Energy Technology Data Exchange (ETDEWEB)
The aerodynamic forces and wake structure of the non-rotating downstream circular cylinder, of which the uniform free stream flow is interfered with another spinning upstream cylinder having the same diameter that is located upstream in a line have been investigated experimentally. When the spin rate of the downstream cylinder defined as the ratio of tangential surface velocity of the spinning cylinder to the free stream velocity increases gradually from zero to 1.4, the change of surface pressure distribution, aerodynamic forces of the non-rotating downstream cylinder were measured in case of several distance ratios of 1.5, 3.0, and 4.5 defined as the ratio of distance between the centers of two cylinders to the diameter. The wake flow patterns behind the cylinder were also investigated in each case. From the present experiments, it has been found that the spin rate significantly influences the ...
1998-03-01
Structural and magnetic studies on the enhancement of the giant magnetoimpedance by ion irradiation
British Library Electronic Table of Contents (United Kingdom)
The mechanism of abrupt increase of the giant magneto impedance (GMI) ratio in the ion irradiated Co-based amorphous ribbon has been investigated. The grazing incident X-ray diffraction and transmission electron microscope were used to characterize the samples before and after ion irradiation. The GMI-ratio considerably increased in the ion irradiated samples and the GMI response showed strong dependence on the driving frequencies. The Barkhausen noise (BN) signals are increased for the Ar ion irradiated sample with dose of 1x10^1^7 ion/cm^2. The results are interpreted in terms of GMI variation associated with domain wall dynamics.
2011-01-01
International Nuclear Information System (INIS)
The effect of a carbohydrate, a 20% protein, or a carbohydrate +0.3% tryptophan TRP breakfast on plasma large neutral amino acid ratio was studied in 6 healthy men. The carbohydrate-rich meal produced shifts in plasma amino acid concentrations such that plasma TRP/LNAA ratios increased from 0.13 to 0.15 (p<0.04) and the protein meal decreased the ratio from 0.14 to 0.11 (p<0.04) after 1 hour. Addition of 0.3% TRP to the carbohydrate-rich meal increased plasma TRP/LNAA ratios more than 2-fold. The TRP containing meal was thus the only one likely to influence brain 5-HT synthesis, although the difference between the plasma TRP/LNAA ratios after carbohydrate and protein breakfasts suggests that the brain may distinguish, by synthesizing more or less 5-HT, the composition of breakfast meals. (Author).
On the fatigue threshold behaviour of two ferrite-pearlite microalloyed steels
Energy Technology Data Exchange (ETDEWEB)
Long crack fatigue threshold ({delta} K{sub th}) and crack closure behaviour of two thermomechanically processed microalloyed (MA) ferrite-pearlite steels are reported. {delta} K{sub th} and crack closure were measured using a dynamic compliance measurement technique. Crack closure was observed at low load ratios (R < 0.5) and the fatigue thresholds decreased with increasing load ratio. In both steels, the closure-free intrinsic threshold ({delta} K{sub eff} {sub th}) was found to be independent of the load ratio. (orig.)
2000-07-01
Results of Am isotopic ratio analysis in irradiated MOX fuels
Energy Technology Data Exchange (ETDEWEB)
For analysis of a small quantity of americium, it is necessary to separate from curium which has similar chemical property. As a chemical separation method for americium and curium, the oxidation of americium with pentavalent bismuth and subsequent co-precipitation of trivalent curium with BIP O{sub 4} were applied to analyze americium in irradiated MOX fuels which contained about 30wt% plutonium and 0.9wt% {sup 241}Am before irradiation and were irradiated up to 26.2GWd/t in the experimental fast reactor Joyo. The purpose of this study is to measure isotopic ratio of americium and to evaluate the change of isotopic ratio with irradiation. Following results are obtained in this study. (1) The isotopic ratio of americium ({sup 241}Am, {sup 242m}Am and {sup 243}Am) can be analyzed in the MOX fuels by isolating americium. The isotopic ratio of {sup 242m}Am and {sup 243}Am increases up ...
1997-04-01
International Nuclear Information System (INIS)
10%Pt/C catalysts were prepared by liquid reduction method. PTFE and Pt/ C catalysts were adhered to porous metal and hydrophobic Pt/C/PTFE catalysts were prepared. The structure and size of Pt crystal particles of Pt/C catalysts were analyzed by XRD, and their mean size was 3.1 nm. The dispersion state of Pt/C and PTFE was analyzed by SEM, and they had good dispersion mostly, but PTFE membrane could be observed on local parts of Pt/C/PTFE surface. Because of low hydrophobicity, Pt/C/ PTFE catalysts have low activity when the mass ratio of PTFE and Pt/C is 0.5: 1, and their catalytic activity increases markedly when the ratio is 1:1. When the ratio increases again, more Pt active sites would be covered by PTFE and interior diffusion effect would increase, which result in the decrease of catalytic activity of Pt/C/PTFE. By PTFE pretreatment of porous metal ...
2007-09-01
[Hormonal disorders in chronic alcoholic intoxication].
Hormone levels were examined in the venous blood in 54 men suffering from stage 2 alcoholism and in 30 normal subjects, using a radioimmunochemical assay. The alcoholics were found to have a statistically significant increase in prolactin and a decrease in testosterone. A definite ratio in the secretion of these hormones differing from that in the control group was elucidated. This ratio (prolactin-testosterone index) is proposed as a diagnostic test of alcoholism. PMID:6441404
1984-01-01
Combustion chamber layout for modern Otto engines
Energy Technology Data Exchange (ETDEWEB)
Since the most efficient way to improve fuel economy in the part-load range is to increase the compression ratio, emphasis is placed on combustion chambers allowing high compression ratios combined with low octane requirements. According to Porsche experience, many demands can be met in the simplest manner by locating the combustion chamber in the piston crown. This configuration offers various advantages over its counterpart installed in the cylinder head. 24 refs.
1981-10-01
Capital management and bank value
British Library Electronic Table of Contents (United Kingdom)
Many banks are under pressure to increase funding by capital, especially equity capital. Return on assets increases, the leverage multiplier declines and the return required by investors should decline as banks increase reliance on equity financing. This article empirically demonstrates the importance of risk and profitability on bank value, and then conceptually illustrates how the price/book ratio and related value should be affected by those banking units either able to issue equity capital or change their capital structure.
2011-01-01
UK PubMed Central (United Kingdom)
Selection of the denitrifying community by plant roots (i.e., increase in the denitrifier/total heterotroph ratio in the rhizosphere) has been reported by several authors. However, very few studies...Full Text Available
2000-09-01
A novel semidry flue gas desulfurization process with the magnetically fluidized bed reactor.
The magnetically fluidized bed (MFB) was used as the reactor in a novel semidry flue gas desulfurization (FGD) process to achieve high desulfurization efficiency. Experiments in a laboratory-scale apparatus were conducted to reveal the effects of approach to adiabatic saturation temperature, Ca/S molar ratio and applied magnetic field intensity on SO(2) removal. Results showed that SO(2) removal efficiency can be obviously enhanced by decreasing approach to adiabatic saturation temperature, increasing Ca/S molar ratio, or increasing applied magnetic field intensity. At a magnetic field intensity of 300Oe and a Ca/S molar ratio of 1.0, the desulfurization efficiency (excluding desulfurization efficiency in the fabric filter) was over 80%, while spent sorbent appeared in the form of dry powder. With the SEM, XRD and EDX research, it can be found that the increase ...
2009-03-18
International Nuclear Information System (INIS)
Based on the Weinberg-Salam theory, the competition of the Neutrino Energy Loss (NEL) rates due to the pair, photo- and plasma process are canvassed. The ratio factor C1, C2 and C3 which correspond the different contributions of the pair, photo- and plasma neutrino process to those of the total NEL rates are accurately taken into account. The ratio factors are very sensitive to the temperature and density. The ratio factor C2 always is lower than the ratio factor C1 and C3. The pair NEL process is the dominant contribution before the crossed point O(C1=C3=0.45) and the plasma NEL process will be the main dominant contribution after the crossed point O. With increasing temperature, the crossed point O will move to the direction of higher density. (authors)
2009-01-01
Energy Technology Data Exchange (ETDEWEB)
An effect of load conditions on Corrosion Fatigue Crack Propagation (CFCP) behavior of High Performance Steel (HPS) under seawater environment was investigated. Fatigue crack propagation tests under several load conditions including stress ratio and load frequency were conducted in air and 3.5% NaCl solution environments. Corrosion/fatigue ratio factor, C/F, particularly was defined to analyze the effect of such conditions. As shown in the results, a decrease of load ratio and frequency leads to an increase of C/F factor. Consequently, under lower loading frequency and stress ratio, the seawater condition causes much more significant effect on CFCP behavior of HPS.
2009-07-01
J* optimization of small aspect ratio stellarator/tokamak hybrid devices
Energy Technology Data Exchange (ETDEWEB)
A new class of low aspect ratio toroidal hybrid stellarators is found using more general plasma confinement optimization criterion than quasi-symmetrization. The plasma current profile and shape of the outer magnetic flux surface are used as control variables to achieve near constancy of the longitudinal invariant J* on internal flux surfaces (quasi-omnigeneity), in addition to a number of other desirable physics target properties. We find that a range of compact (small aspect ratio A), high {beta} (ratio of thermal energy to magnetic field energy), low plasma current devices exist which have significantly improved confinement both for thermal as well as energetic (collisionless) particle components. With reasonable increases in magnetic field and geometric size, such devices can also be scaled to confine 3.5 MeV alpha particle orbits.
1997-12-31
Energy Technology Data Exchange (ETDEWEB)
One of the unsolved problems of the natural gas dual fuel engine is that there is too much exhaust of Total Hydrogen Carbon(THC) at a low equivalent mixture ratio. To fix it, a natural gas mixed with hydrogen was applied to engine test. The results showed that the higher the mixture ratio of hydrogen to natural gas, the higher the combustion efficiency. And when the amount of the intake air is reached to 90% of WOT, the combustion efficiency was promoted. But, like a case making the injection timing earlier, the equivalent mixture ratio for the nocking limit decreases and the produce of NOx increases. 5 refs., 9 figs., 1 tab.
1999-05-28
Mathematical modeling of a direct contact humidification?dehumidification desalination process
British Library Electronic Table of Contents (United Kingdom)
Using air as a carrier gas is common in humidification?dehumidification desalination processes. A computer program was written using mass and energy balances for modeling the process behavior. The parameters considered in this work were inlet air and fresh water recycle temperatures, inlet air flow rate, saline water and fresh water recycle flow rates, and saline water to air flow ratio. Results of simulation showed that increasing inlet air and fresh water recycle flow rate increases fresh water production. It was also found that heating the inlet air to humidification column or cooling the inlet water to dehumidification column increases the production rate but increasing water to air flow ratio in a humidifier leads to a lower production rate. The predicted effects of the parameters on ...
2009-01-01
Vibration characteristics of SMA composite beams with different boundary conditions
Energy Technology Data Exchange (ETDEWEB)
Recently, the development of shape memory alloy (SMA) actuators, in the forms of wire, thin film and stent have been found increasingly in the fields of materials science and smart structures and engineering. The increase in attraction for using these materials is due to their many unique materials, mechanical, thermal and thermal-mechanical properties, which in turn, evolve their subsequent shape memory, pseudo-elasticity and super-elasticity properties. In this paper, a common type of SMA actuator, Nitinol wires, were embedded into advanced composite structures to modulate the structural dynamic responses, in terms of natural frequency and damping ratio by using its shape memory and pseudo-elastic properties. A simple theoretical model is introduced to estimate the natural frequency of the structures before and after actuating the embedded SMA wires. The damping ratios of different SMA composite beams ...
2002-12-15
Novel in situ polymerizable liquid three-arm biodegradable oligomeric polyesters based upon glycolic acid (GA), L-lactic acid (LLA), and their copolymers are synthesized and characterized. Injectable and in situ curable polymer neat resins and their composites formulated with bioabsorbable beta-tricalcium phosphate are prepared at room temperature using photo- and redox-initiation systems, respectively. The cured neat resins show the initial compressive yield strength (YCS, MPa), modulus (M, MPa), ultimate compressive strength (UCS, MPa), and toughness (T, kN mm), ranging from 4.0 to 20.1, 201.5 to 730.2, 82.7 to 310.5, and 1.02 to 3.93. The cured composites show the initial YCS, M, UCS and T, ranging from 27.7 to 56.4, 1440 to 4870, 81.6 to 158.9, and 0.94 to 1.97. Increasing GA/LLA ratio increases all the initial compressive strengths of both neat resins and composites. Increasing filler content ...
2006-08-18
Modification of surface texture by grinding and polishing lead zirconate titanate ceramics
Energy Technology Data Exchange (ETDEWEB)
This paper reports that grinding and polishing affected the orientation of 90[degrees] domains at the surface of lead zirconate titanate (PZT) ceramics. This was quantified by using changes in the intensity ratio of the (002) and (200) X-ray reflections. Grinding unpoled PZT with 600-grit SiC paper gave X-ray intensity ratios similar to those of poled material. This implies that 90[degrees] domain realignments had occurred in the near surface region probed by the X-rays. Grinding poled samples with 600-grit SiC further increased the X-ray intensity ratio beyond that caused by poling, indicating that additional surface reorientation of 90[degrees] domains had occurred. The effects of diamond polishing depended on the size of the diamond particles. The use of 6-[mu]m diamond had no effect on the (002)/(200) intensity ratio of either poled or unpoled samples, while polishing with 15- ...
1992-08-01
Modification of surface texture by grinding and polishing lead zirconate titanate ceramics
International Nuclear Information System (INIS)
This paper reports that grinding and polishing affected the orientation of 90 degrees domains at the surface of lead zirconate titanate (PZT) ceramics. This was quantified by using changes in the intensity ratio of the (002) and (200) X-ray reflections. Grinding unpoled PZT with 600-grit SiC paper gave X-ray intensity ratios similar to those of poled material. This implies that 90 degrees domain realignments had occurred in the near surface region probed by the X-rays. Grinding poled samples with 600-grit SiC further increased the X-ray intensity ratio beyond that caused by poling, indicating that additional surface reorientation of 90 degrees domains had occurred. The effects of diamond polishing depended on the size of the diamond particles. The use of 6-#mu#m diamond had no effect on the (002)/(200) intensity ratio of either poled or unpoled samples, while polishing with 15- or ...
1992-01-01
Stability ranges of Li-#alpha#'-sialons
International Nuclear Information System (INIS)
The formation of #alpha#'-sialon using Li as a modifying cation was investigated. The effects of the Li content, firing temperatures and Si/Al ratios on #alpha#'- yield were studied. The results indicated that at lower sintering temperatures the stabilisation of #alpha#'-sialons was obtained but the high weight losses of Li at higher temperatures limited the stabilisation. Increased ''Al'' content in the compositions resulted in an increase in the stability of Li-#alpha#'-sialon at higher temperatures, by the formation of a liquid phase which retains Li in the system. (orig.).
1993-10-04
British Library Electronic Table of Contents (United Kingdom)
Summary The objective of this study was to examine the role of root carbohydrate levels and metabolism in the waterlogging tolerance of contrasting mung bean genotypes. An experiment was conducted with two cultivated mung bean (Vigna radiata) genotypes viz., T44 (tolerant) and Pusa Baisakhi (PB) (susceptible), and a wild Vigna species Vigna luteola under pot-culture to study the physiological and molecular mechanism of waterlogging tolerance. Waterlogging resulted in decrease in relative water content (RWC), membrane stability index (MSI) in root and leaf tissues, and chlorophyll (Chl) content in leaves, while the Chl a/b ratio increased. Waterlogging-induced decline in RWC, MSI, Chl and increase in Chl a/b ratio was greater in PB than V. luteola and T44. Waterlogging caused decline in tot...
2009-01-01
Energy Technology Data Exchange (ETDEWEB)
Hydrous pyrolysis of immature Monterey Phosphatic or Siliceous rock at progressively higher temperatures causes systematic changes in biomarker thermal maturity parameters of the generated hydrocarbons. Biomarker ratios based on proposed carbon-carbon cracking or aromatization reactions increase during hydrous pyrolysis along similar pathways for both Siliceous and Phosphatic members. An increase in these biomarker ratios is also observed for oils of increasing thermal maturity from the offshore Santa Maria Basin, although the rates of changes for each parameter differ between the hydrous pyrolysis and natural samples. Changes in some cracking parameters during maturation appear to result from differential thermal stability of the compounds rather than conversion of precursors to products. (author).
1990-01-01
A sulfonated fluoroalkyl graft polymer (FGP) membrane was prepared as a polymer electrolyte. First, the FGP membrane was grafted with styrene under UV irradiation. The grafted FGP was then sulfonated to functionalize it for proton conductivity. The grafting degree of the membrane increased with increasing grafting time during UV irradiation. The proton conductivity of the membrane increased with increasing grafting degree. The swelling ratio was independent of the grafting time, however, the water uptake increased with increasing grafting degree. Based on these results, it was found that the UV-initiated styrene grafting occurred along the membrane thickness direction. Moreover, the membrane was embedded within the glass fibers of the composite. This composite electrolytic membrane had 1.15 times the proton conductivity of a Nafion 117 ...
2011-03-01
Energy Technology Data Exchange (ETDEWEB)
K{beta}-to-K{alpha} X-ray intensity ratios of Ti, V, Cr, and Co in pure metals and their disilicide compounds have been measured following excitation by 59.54 keV {gamma}-rays from a 200 mCi {sup 241}Am point-source. The K{beta}-to-K{alpha} intensity ratios of all these metals in the disilicide compounds are found to be less than the corresponding ratios for pure metals. Comparison of the measured K{beta}-to-K{alpha} intensity ratios for the disilicides and pure metals with the multiconfiguration Dirac-Fock calculations indicates increase of the 3d electron populations of Ti, V, Cr, and Co in the disilicides from their pure metal values suggesting the rearrangement of electrons between 3d and 4s states of the individual metal atom. This rearrangement is found to be opposite to that observed in our previously reported work on NiSi{sub 2} and CuSi{sub 2}.
1999-06-01
International Nuclear Information System (INIS)
K#beta#-to-K#alpha# X-ray intensity ratios of Ti, V, Cr, and Co in pure metals and their disilicide compounds have been measured following excitation by 59.54 keV #gamma#-rays from a 200 mCi "2"4"1Am point-source. The K#beta#-to-K#alpha# intensity ratios of all these metals in the disilicide compounds are found to be less than the corresponding ratios for pure metals. Comparison of the measured K#beta#-to-K#alpha# intensity ratios for the disilicides and pure metals with the multiconfiguration Dirac-Fock calculations indicates increase of the 3d electron populations of Ti, V, Cr, and Co in the disilicides from their pure metal values suggesting the rearrangement of electrons between 3d and 4s states of the individual metal atom. This rearrangement is found to be opposite to that observed in our previously reported work on NiSi_2 and CuSi_2.
1999-06-01
Energy Technology Data Exchange (ETDEWEB)
A new hydroxyiminoamide ligand, 1-(2-nitroimidazole-1-yl)-propanhydroxyiminoamide (N2IPA) was synthesized. The biodistribution of {sup 99m}Tc-N2IPA in mice bearing S180 tumor demonstrated that the complex showed a selective accumulation in tumor and slow clearance from it. The tumor-to-tissue uptake ratios increased with time. At 4 hours after injection, the uptake ratios of tumor to muscle, blood, liver, heart, and lung reached 8.4, 1.5, 0.6, 2.9, and 2.3, respectively. Moreover, the tumor-to-liver uptake ratio steadily increased to 0.9 at 8 hours and 2.3 at 24 hours. The complex showed little uptake and quick clearance in blood, lung and other organs. Compared with other proposed hypoxia-imaging agents, this novel agent has advantages of higher tumor-to-muscle and tumor-to-blood uptake ratios and easier synthesis.
2004-02-01
Energy Technology Data Exchange (ETDEWEB)
In isolated rat adipocytes, insulin inhibits lipolysis to a greater extent than would be predicted by the decrease in (-/+)cAMP activity ratio of cAMP-dependent protein kinase (A-kinase), from which it was speculated that insulin promotes the dephosphorylation of hormone-sensitive lipase. They have examined the phosphorylation state of cellular proteins under conditions of varying A-kinase activities in the presence and absence of insulin. Protein phosphorylation was determined by SDS-PAGE electrophoresis of extracts from /sup 32/P-loaded cells; glycerol and A-kinase activity ratios were measured in the cytosolic extracts from control, non-radioactive cells. Increased protein phosphorylation in general occurred over the same range of A-kinase activity ratios, 0.1-0.3, associated with increased glycerol release. The insulin-induced decrease in lipolysis was associated with a decrease ...
1987-05-01
Calcination of Fluorinel-sodium waste blends using sugar as a feed additive (formerly WINCO-11879)
Energy Technology Data Exchange (ETDEWEB)
Methods were studied for using sugar as a feed additive for converting the sodium-bearing wastes stored at the Idaho Chemical Processing Plant into granular, free flowing solids by fluidized-bed calcination at 500{degrees}C. All methods studied blended sodium-bearing wastes with Fluorinel wastes but differed in the types of sugar (sucrose or dextrose) that were added to the blend. The most promising sugar additive was determined to be sucrose, since it is converted more completely to inorganic carbon than is dextrose. The effect of the feed aluminum-to-alkali metal mole ratio on calcination of these blends with sugar was also investigated. Increasing the aluminum-to-alkali metal ratio from 0.6 to 1.0 decreased the calcine product-to-fines ratio from 3.0 to 1.0 and the attrition index from 80 to 15%. Further increasing the ratio to 1.25 had no effect.
1992-06-01
Energy Technology Data Exchange (ETDEWEB)
Producing nuclear energy in order to reduce anthropic CO{sub 2} emission and to meet high energy demand, implies three conditions to the nuclear plants of the IV. generation: safety improvements, radioactive waste minimization, and fuel breeding for a sustainable use of the resources. The Thorium fuel cycle used in Molten Salt Reactors seems promising. Many numerical studies based on probabilistic codes are carried out in order to analyse the behaviour of such reactors. Nevertheless, one of the most important parameters is badly known: the alpha ratio of {sup 233}U, ratio of the neutron capture cross section to fission one for {sup 233}U. This key-parameter is necessary to calculate the breeding ratio and thus, the deployment capacities of those reactors. This Ph-D thesis was intended to prepare a precise measurement of the alpha ratio of {sup 233}U between 1 eV and 10 keV. Preliminary measurements have ...
2007-12-15
Inductively coupled fluorocarbon (CF4/Ar and C4F8/Ar) plasmas were used to etch HfO2, which is a promising high-dielectric-constant material for the gate of complementary metal-oxide-semiconductor devices. The etch rates of HfO2 in CF4/Ar plasmas exceeded those in C4F8/Ar plasmas. The tendency for etch rates to become higher in fluorine-rich (high F/C ratio) conditions indicates that HfO2 can be chemically etched by fluorine-containing species. In C4F8/Ar plasmas with a high Ar dilution ratio, the etch rate of HfO2 increased with increasing bias power. The etch rate of Si, however, decreasd with bias power, suggesting that the deposition of carbon-containing species increased with increasing the power and inhibited the etching of Si. The HfO2/Si selectivity monotonically increased with increasing power, then became more ...
2005-11-01
Energy Technology Data Exchange (ETDEWEB)
It is postulated that a break of a thin-walled pipe does not cause a subsequent break in the pipe in the vicinity of a plastic hinge even when the wall is weakened by a 60 circumferential crack of a depth of 30% of the wall thickness on the tension side. This pipe behavior is the result of plastic buckling in the compression side and applies to pipes of diameter-to-thickness ratio larger than 20. For this type of pipe, the axial strains decrease with increasing diameter-to-thickness ratio in the tension side. As the pipe is only loaded in one direction, there is no cyclic behavior that can trigger a subsequent break. (orig.)
1993-10-01
Experimental and theoretical analysis of compression ratio on Otto-cycle engines. Pt. 1
Energy Technology Data Exchange (ETDEWEB)
The increase of the compression ratio of Otto carburator engines up to epsilon = 14 was investigated by Audi in its research department at Neckarsulm. The results are presented in three partial reports. Part one describes the Audi fuel method and demonstrates the effects of the main parameters. Part two shows the influence of the current on the combustion by the help of a new measuring method developed by the Institut fuer Physikalische Elektronik at Stuttgart University. Part three provides a theoretical analysis of the data gained in the investigations.
1982-01-01
Techno-economic investigation of an air humidification-dehumidification desalination process
Energy Technology Data Exchange (ETDEWEB)
This article presents a humidification-dehumidification (H.D.) process suitable for desalination of sea- and brackish water. The work correlated performance characteristics of the combination of different components in such a loop. Water yield, energy requirement and design data are evaluated as functions of different parameters. The investigation covered water to air mass ratios ranging from 60 to 80, concentration ratios between 2 and 5, at a temperature difference of between 10 and 16 C, along the liquid for dehumidification. The results showed that 76% of energy consumed in the humidifier is recovered by condensation. Increase of the concentration ratio to 5 can reduce the make-up water and rejected brine by about 58% and 24% respectively. Cost calculations show that the H.D. process has significant potential as an alternative for small capacity desalination plants and permits to operate systems as ...
1993-08-01
J{sup {asterisk}} optimization of small aspect ratio stellarator/tokamak hybrid devices
Energy Technology Data Exchange (ETDEWEB)
A new class of low aspect ratio toroidal hybrid stellarators is found using a more general plasma confinement optimization criterion than quasisymmetrization. The plasma current profile and shape of the outer magnetic flux surface are used as control variables to achieve near constancy of the longitudinal invariant J{sup {asterisk}} on internal flux surfaces (quasiomnigeneity), in addition to a number of other desirable physics target properties. A range of compact (small aspect ratio A), low plasma current devices have been found with significantly improved confinement, both for thermal as well as energetic (collisionless) particle components. With reasonable increases in magnetic field and geometric size, such devices can also be scaled to confine 3.5 MeV alpha particle orbits.
1998-05-01
Joint shear strength of FRP reinforced concrete beam-column joints
British Library Electronic Table of Contents (United Kingdom)
An assessment of the joint shear strength of exterior concrete beam-column joints reinforced internally with Glass Fibre Reinforced Polymer (GFRP) reinforcements under monotonically increasing load on beams keeping constant load on columns is carried out in this study. Totally eighteen numbers of specimens are cast and tested for different parametric conditions like beam longitudinal reinforcement ratio, concrete strength, column reinforcement ratio, joint aspect ratio and influence of the joint stirrups at the joint. Also finite element analysis is performed to simulate the behaviour of the beam-column joints under various parametric conditions. Based on this study, a modified design equation is proposed for assessing the joint shear strength of the GFRP reinforced beam-column specimens b...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
Pulsed DC-plasma nitriding has been applied to form nitride layer having only a diffusion layer. The discharge current with the variation of discharge gases is proportional to the intensity of N{sub 2}{sup +} peak in optical emission spectroscopy during the plasma nitriding. The discharge current, microhardness in surface of substrate and depth of nitride layer increased with the ratio of N{sub 2} to H{sub 2} gas in discharge gases. When the ratio of N{sub 2} to H{sub 2} is lower than 60% in the discharge gases, high microhardness value of 1100Hv nitride layer which contains no compound layer has been formed. (author). 20 refs., 6 figs., 1 tab.
2002-06-01
Characterization of humic acids extracted from mined lignite and from their oxidation products
Energy Technology Data Exchange (ETDEWEB)
An oxidative method for enriching the content of humic acids in a mined lignite from Umbria (central Italy) is described. A mild oxidation using H{sub 2}O{sub 2} in an alkaline medium was successful in increasing the percentage of lignite-derived humidifed carbon from 5.77% to 33.67%. The newly formed humic acids showed a higher number of oxygen-bearing functional groups, a lower carbon/oxygen ratio and a higher absorbance ratio at 465 and 665 nm (E{sub 4}/E{sub 6}) in diluted solution compared to the native lignite-derived humic acids. A high E{sub 4}/E{sub 6} ratio indicated less condensation of the aromatic nucleus and a lower molecular weight in comparison to the lignite-derived native humic acids.
1999-05-01
A method for determining the origin of bitumoids
Energy Technology Data Exchange (ETDEWEB)
The invention is associated with organic geochemistry and may be used in conducting geological exploration operations for oil and gas. The purpose of the invention is to increase the precision of the method for determining the genesis of bitumoids. This is achieved through determining the isotopic composition of nickel or vanadium and from the anomalously high values of the isotopic ratio of Ni-58 to Ni-62 or from the anomalously low values of the isotopic ratio of vanadium, a conclusion is drawn about the epigenetic nature of the bitumoids. The proposed method is characterized by greater resolution due to the fact that the values of the isotopic ratios for oil bearing and water bearing structures are essentially not superimposed. The proposed method exceeds the resolution of metal metering studies in conducting geological exploration for oil and gas by 2 to 3 times.
1983-01-01
International Nuclear Information System (INIS)
The effects of gamma irradiation at 0.2#approx#0.4 Mrad and condition for processing of buckwheat noodles on sensory quality and physical properties were investigated. The results were as follows: (1) Sensory evaluation of buckwheat noodles, prepared with the 70 % ratio of buckwheat flour, was decreased according to an increase of irradiation dose of buckwheat flour. Hardness and adhesiveness of buckwheat noodles caused by irradiation should be given large effect to the texture. Elasticity of buckwheat noodles was linearly decreased with increasing of irradiation dose of buckwheat flour, and elasticity of buckwheat noodles was decreased about 15 % by an increase of irradiation dose at 0.3 Mrad. (2) Maximum torque in Farinograph test was linearly decreased with increasing of irradiation dose of buckwheat flour, and maximum torque was decreased about 3 % by ...
1989-01-01
Energy Technology Data Exchange (ETDEWEB)
Swirling flow in a direct injection diesel engine was measured by a laser doppler velocimeter. Piston cavity diameter and top clearance volume were changed as factors affecting swirling flow to study the distribution of swirling flow speed. When using the same intake port and changing the opening ratio of piston cavity, the distribution of swirling flow speed was different by the cavity during intake process but these agree just after opening intake valve and then become again different by cavity. When increasing top clearance and decreasing compression ratio, the axial symmetry of flow during commpression process increases. When changing piston cavity, and also when changing intake port, the mean swirling ratio in inside and outside areas of combustion chamber has common tendency to increase and decrease respectively. The mean swirling flow in the combustion ...
1989-05-31
Estimation of CHF ratio at various power levels in TAPP-3 and 4 reactors
International Nuclear Information System (INIS)
TAPP-3 and 4 are the 540 MWe PHWRs having horizontal fuel channel. At normal 100% FP operation there is no boiling in the channel. However, when the power increases due to any transient, the boiling may start in the channel. The main application for critical heat flux (CHP) prediction is to set the operating power with a comfortable margin to avoid CHF occurrence. This margin of CHF can be expressed in terms of minimum critical heat flux ratio (MCHFR), which is the ratio of CHF to local heat flux for the same pressure, mass flux and quality. The CHF depends on power, coolant flow rate as well as coolant condition in the channel. As the power increases the flow reduces in the channel and cooling is degraded. The thermal hydraulic code is developed for present analysis. The output of analysis are CHF prediction quality calculation at axial locations of the maximum rated channel at various power levels and ...
2005-12-01
Double-diffusive convection in a Darcy porous medium saturated with a couple-stress fluid
Energy Technology Data Exchange (ETDEWEB)
The onset of double-diffusive convection in a couple-stress fluid-saturated horizontal porous layer is studied using linear and weak nonlinear stability analyses. The modified Darcy equation that includes the time derivative term and the inertia term is used to model the momentum equation. The expressions for stationary, oscillatory and finite-amplitude Rayleigh number are obtained as a function of the governing parameters. The effect of couple-stress parameter, solute Rayleigh number, Vadasz number and diffusivity ratio on stationary, oscillatory and finite-amplitude convection is shown graphically. It is found that the couple-stress parameter and the solute Rayleigh number have a stabilizing effect on stationary, oscillatory and finite-amplitude convection. The diffusivity ratio has a destabilizing effect in the case of stationary and finite-amplitude modes, with a dual effect in the case of oscillatory convection. The Vadasz number advances ...
2010-06-15
Double-diffusive convection in a Darcy porous medium saturated with a couple-stress fluid
International Nuclear Information System (INIS)
The onset of double-diffusive convection in a couple-stress fluid-saturated horizontal porous layer is studied using linear and weak nonlinear stability analyses. The modified Darcy equation that includes the time derivative term and the inertia term is used to model the momentum equation. The expressions for stationary, oscillatory and finite-amplitude Rayleigh number are obtained as a function of the governing parameters. The effect of couple-stress parameter, solute Rayleigh number, Vadasz number and diffusivity ratio on stationary, oscillatory and finite-amplitude convection is shown graphically. It is found that the couple-stress parameter and the solute Rayleigh number have a stabilizing effect on stationary, oscillatory and finite-amplitude convection. The diffusivity ratio has a destabilizing effect in the case of stationary and finite-amplitude modes, with a dual effect in the case of oscillatory convection. The Vadasz number advances ...
2010-06-01
International Nuclear Information System (INIS)
The precipitation reaction of some rare earth chlorides (La/Ce/Nd/GdCl3) in a LiCl-KCl molten salt has been carried out by using the oxygen sparging method. In this study, regardless of the oxygen sparging time and the molten salt temperature, oxychlorides (REOCl) for LaCl3, NdCl3 and GdCl3, and an oxide (REO2) for CeCl3 are formed as a precipitate. The conversion of rare-earth chlorides into insoluble precipitates was described by using a conversion ratio. The conversion ratio increased exponentially with the oxygen sparging time and finally showed asymptotic value at 1,023K of the molten salt temperature condition. The conversion ratios of LaCl3, NdCl3 and GdCl3 were increased with the molten salt temperature, however, even though the conversion ratio was increased from 0.660 to 0.995 with increasing molten salt ...
2006-10-01
International Nuclear Information System (INIS)
Nano structured carbon nitride thin films were deposited at different RF powers in the range of 50 W to 225 W and constant gas ratio of (argon: nitrogen) Ar:N_2 by RF magnetron sputtering. The atomic percentage of Nitrogen: Carbon (N/C) content and impedance of the films increased from 14.36% to 22.31% and 9 x 10"-"1 #OMEGA# to 7 x 10"5 #OMEGA# respectively with increase in RF power. The hardness of the deposited films increased from 3.12 GPa to 13.12 GPa. The increase in sp"3 hybridized C-N sites and decrease of grain size with increase in RF power is responsible for such variation of observed mechanical and electrical properties.
2010-10-01
Energy Technology Data Exchange (ETDEWEB)
Increases in atmospheric CO[sub 2] are predicted to cause an increase in the C:N ratio of plant substrates entering the soil organic matter pool. We experimentally increased soil C:N ratios by adding 40 g C/m[sup 2] as sucrose (metabolic C) or cellulose (structural C) in short-, mid-, and tall-grass plots in the Serengeti Ecosystem, and measured plant productivity, plant nutrient uptake rates, and mineralization rates. Experimental treatments also included fencing to exclude grazing and additions of 40 g N/m[sup 2] as urea to simulate a urine hit from an average-sized ungulate. Productivity was only 60% of controls in C-addition plots, and was similar for sucrose and cellulose. However, this response was not observed in the short-grass site, an area of relatively low rainfall and high fertility. These results support the role of a plant-microbe negative feedback mechanism on plant ...
1994-06-01
Effect of grain size on engineering properties of coal ash
Energy Technology Data Exchange (ETDEWEB)
The main object of the present study was to obtain the relationship of primary, secondary and index properties; compressibility; and angle of repose of coal ash. Representative samples of coal ash from different storage locations of Ropar thermal power plant, Punjab, were analysed. Based on test results of various primary characteristics of ash, the following observations have been made. (1) Ashes sampled for the study have a common mineralogical origin. The uniformity coefficient increases for ash collected near location of discharge compared to ash collected far from the location. (2) The void ratio extent, that is, a different of emax. or a ratio of emax. and emin. decreases with an increase of mean size. The maximum dry density obtained in dry vibration and proctor test differs for fine ash. Maximum dry density decreases and optimum moisture content increases with ...
2003-07-01
A modeling and experimental study of flue gas desulfurization in a dense phase tower.
We used a dense phase tower as the reactor in a novel semi-dry flue gas desulfurization process to achieve a high desulfurization efficiency of over 95% when the Ca/S molar ratio reaches 1.3. Pilot-scale experiments were conducted for choosing the parameters of the full-scale reactor. Results show that with an increase in the flue gas flow rate the rate of the pressure drop in the dense phase tower also increases, however, the rate of the temperature drop decreases in the non-load hot gas. We chose a water flow rate of 0.6 kg/min to minimize the approach to adiabatic saturation temperature difference and maximize the desulfurization efficiency. To study the flue gas characteristics under different processing parameters, we simulated the desulfurization process in the reactor. The simulated data matched very well with the experimental data. We also found that with an increase in the Ca/S molar ...
2011-03-05
British Library Electronic Table of Contents (United Kingdom)
In this research, the interactive effect of grain and specimen sizes on the flow stress of sheet metal in microforming is investigated via the tensile test of pure copper and numerical modeling. Models based on different assumptions are proposed to analyze the size effect phenomenon. It is found that the flow stress decreases linearly with the decrease of the ratio of specimen to grain sizes. The grain boundary thickness decreases and its volume fraction increases with the decrease of grain size. The variation of grain boundary thickness is not proportional to the variation of grain size. Furthermore, the fraction of grain boundary increases with the strain and the ratio of specimen to grain sizes. Based on the FE simulation, it is found that the simulated flow stress, which is modeled bas...
2011-01-01
International Nuclear Information System (INIS)
The phase separation of (water + salt + polyethylene glycol 15000) systems was studied by cloud-point measurements using the particle counting method. The effect of three kinds of sulphate salt (Na2SO4, K2SO4, (NH4)2SO4) concentration, polyethylene glycol 15000 concentration, mass ratio of polymer to salt on the cloud-point temperature of these systems have been investigated. The results obtained indicate that the cloud-point temperatures decrease linearly with increase in polyethylene glycol concentrations for different salts. Also, the cloud points decrease with an increase in mass ratio of salt to polymer.
2009-07-01
Energy Technology Data Exchange (ETDEWEB)
Objective: To assess dynamic MRI with Gd-DTPA enhancement for evaluating inflammatory changes in the subacromial bursa. Design and patients: We detected the signal intensity changes in dynamic MRI of the subacromial bursa, and confirmed these macroscopically by arthroscopy and histologically. The signal intensity was measured using built-in software, and the enhancement ratio (E ratio) was calculated from dynamic MR images. In addition, as a parameter of the rate of the increase in the signal intensity from 0 to 80 s, the mean increase per second in the E ratio was obtained as the coefficient of enhancement (CE). The correlation was studied of the E ratio and CE with the arthroscopic findings (redness, villous formation, thickening and adhesion), and of the E ratio and CE with the histological findings (capillary proliferation, papillary ...
2003-09-01
Valence electronic structure of Ni in Ni-Si alloys from relative K X-ray intensity studies
Energy Technology Data Exchange (ETDEWEB)
The K{beta}-to-K{alpha} X-ray intensity ratio of Ni in Ni{sub 3}Si, Ni{sub 2}Si and NiSi has been determined by energy dispersive X-ray fluorescence technique. It is found that the intensity ratio of Ni decreases from pure Ni to Ni{sub 2}Si and then increases from Ni{sub 2}Si to NiSi, in good agreement with the electronic structure calculations cited in the literature. We have also performed band structure calculations for pure Ni in various atomic configurations by means of linear muffin-tin orbital method and used this data with the normalized theoretical intensity ratios cited in the literature to estimate the 3d-occupation numbers of Ni in Ni-Si alloys. It is emphasized that investigation of alloying effect in terms of X-ray intensity ratios should be carried out for the stoichiometric alloys in order to make reliable and quantitative comparisons between theory and experiment in ...
2007-02-15
Evaluation of femoral head perfusion by dynamic MRI
International Nuclear Information System (INIS)
The purpose of this study was to evaluate the usefulness of dynamic MRI for femoral head perfusion. Objects were 64 femoral heads of 44 normal cases (20-95 years old), 10 cases (33-90 y) of femoral neck fracture and 8 cases (61-86 y) using steroid due to articular rheumatism, nephrosis and other diseases. Siemens 1.0 T Magneton Impact with body array coil was used for dynamic MRI by the fast low-angle shot 2D method for every 17 sec interval. Gd-DTPA was injected intravenously. ROI was defined in the center of femur head and of trochanter to monitor their values for the dynamic curve. Evaluation was done on the ratio of enhancement ratio (ER) in the head/trochanter and on the curve in both heads. In normal cases, the head ER was significantly lower in >60 years old cases. There was neither significant correlation between their head/trochanter ER ratios nor significant difference between their dynamic curves. In fracture ...
1998-05-01
Performance of single cylinder, direct injection diesel engine using water fuel emulsions
Energy Technology Data Exchange (ETDEWEB)
A single cylinder diesel engine study of water-in-diesel emulsions was conducted to investigate the effect of water emulsification on the engine performance and gases exhaust temperature. Emulsified Diesel fuels of 0, 5, 10, 15 and 20 water/diesel ratios by volume were used in a single cylinder, direct injection diesel engine, operating at 1200-3300 rpm. The results indicate that the addition of water in the form of emulsion improves combustion efficiency. The engine torque, power and brake thermal efficiency increase as the water percentage in the emulsion increases. The average increase in the brake thermal efficiency for 20% water emulsion is approximately 3.5% over the use of diesel for the engine speed range studied. The proper brake specific fuel consumption and gases exhaust temperature decrease as the percentage of water in the emulsion increases. (author)
2004-03-01
Support effects on CO hydrogenation over Ru/zeolite catalysts
Energy Technology Data Exchange (ETDEWEB)
Hydrogenation of carbon monoxide at 101.3 kPa has been studied over a series of ion-exchanged Ru catalysts supported on NaX, NaY, KL, Na mordenite, and HY zeolites. The type of zeolite had pronounced effects on the activity and selectivity of the Ru. The specific activity would appear to be related to the dispersion of reduced ruthenium in the zeolite. Methane selectivity, however, seems to be strongly influenced by the type and concentration of alkali cations remaining in the ion-exchanged zeolite. These cations appear to promote chain growth much as traditional alkali promoters would, though perhaps more indirectly. Due to bifunctional properties of the zeolite-supported catalysts, a significant fraction of C/sub 4/ was in the form of isobutane. Formation of isobutane seems to be related to either the Si/Al ratio in the zeolites or the concentration of the remaining alkali cations, but not to the OH concentration. In addition, H/sub 2/ chemisorption at 25/sup 0/C ...
1984-02-01
Lead recycling; Namari no recycle
Energy Technology Data Exchange (ETDEWEB)
In Japan, lead has been widely used for gasoline additives, inorganic chemicals such as pigment, lead pipes/plates, and coating materials of cable. Because of the steady increase in car population and the mounting of environmental concern, lead consumption ratio for lead-acid batteries is tending to increase gradually up to 70% with decreasing the consumption for gasoline additives. This paper describes the recycling of lead-acid batteries in Japan. Since the latter half of FY 1994, the battery manufacturing industry started the new lead recycling system. The recycling ratio of the used lead-acid batteries became 90% in 1996 from 84% in 1994. In near future, it can reach to 95%, the recycling ratio in some European countries. The primary smelting occupies 53%, and the secondary smelting occupies 47%. For the conventional method by secondary smelting makers, reduction smelting and ...
1997-12-25
Energy Technology Data Exchange (ETDEWEB)
Experimental investigation of heat transfer and friction factor characteristics of circular tube fitted with full-length helical screw element of different twist ratio, and helical screw inserts with spacer length 100, 200, 300 and 400mm have been studied with uniform heat flux under laminar flow condition. The experimental data obtained are verified with those obtained from plain tube published data. The effect of spacer length on heat transfer augmentation and friction factor, and the effect of twist ratio on heat transfer augmentation and friction factor have been presented separately. The decrease in Nusselt number for the helical twist with spacer length is within 10% for each subsequent 100mm increase in spacer length. The decrease in friction factor is nearly two times lower than the full length helical twist at low Reynolds number, and four times lower than the full length helical twist at high Reynolds number for ...
2007-02-15
Energy Technology Data Exchange (ETDEWEB)
The relationship between coal properties and liquefaction or gasification characteristics was analyzed by using the analysis and test results and liquefaction characteristics in the coal data base. On liquefaction reaction, the close relation between an oil yield and coal constituent composition or a coal rank is well-known. Various multivariable regression analyses were conducted by using 6 factors as variables such as calorific value, volatile component, O/C and H/C atomic ratios, exinite+vitrinite content and vitrinite reflectance, and liquefaction characteristics as variate. On liquefaction characteristics, the oil yield of dehydrated and deashed coals, asphaltene yield, hydrogen consumption, produced water and gas quantities, and oil+asphaltene yield were predicted. The theoretical gasification efficiency of each specimen was calculated to evaluate the liquefaction reaction obtained. As a result, the oil yield increased with H/C atomic ...
1996-10-28
A rapidly hydrated sorbent for moderate-temperature dry flue gas desulfurization was prepared by rapidly hydrating adhesive carrier particles and lime. The circulation ash from a circulating fluidized bed boiler and chain boiler ash, both of which have rough surfaces with large specific surface areas and specific pore volumes, can improve the adhesion, abrasion resistance, and desulfurization characteristics of rapidly hydrated sorbent when used as the adhesive carrier particles. The adhesion ability of sorbent made from circulation ash is 67.4% higher than that of the existing rapidly hydrated sorbent made from fly ash, the abrasion ratio is 76.2% lower, and desulfurization ability is 14.1% higher. For sorbent made from chain boiler ash, the adhesion ability is increased by 74.7%, the desulfurization ability is increased by 30.3%, and abrasion ratio is decreased by 52.4%. The abrasion ...
2010-06-15
Effect of site wind properties on wind-electric conversion costs
Energy Technology Data Exchange (ETDEWEB)
The unit cost of energy production of wind generators is examined by means of a model of the turbine power curve and the Weibull model of wind probability function, by applying the usual economic equations. The analysis is carried out in terms of dimensionless variables whose range of variability is defined by examining the data of 80 modern commercial wind turbines; likewise, the economic parameters are based on the present state of costs. The unit cost decreases asymptotically when alpha (ratio between mean wind speed and cut-in speed) - increases and shows a lower limit of 2 to 5 Ecent/kWh. This cost depends both on the value of the machine parameter {phi} (ratio between nominal and cut-in speed) and on the basic prices. The effect of the Weibull shape parameter kappa is different according to the values of {alpha} and {phi}: with low {alpha} and high {phi} the unit cost increases along with {kappa} ...
2004-12-01
Combustion for high temperature heating process
Energy Technology Data Exchange (ETDEWEB)
This paper describes the high-temperature (1500/sup 0/C or higher) heating technology by combusting natural gas. The theoretical adiabatic flame temperature is 1957/sup 0/C at the theoretical air ratio and 2801/sup 0/C at the theoretical oxygen ratio. The flame temperature is increased by 40/sup 0/C every 1%-increase of oxygen up to 25% of the concentration of oxygen and by 28/sup 0/C to 30% of it. The flame temperature is increased by 37 to 38/sup 0/C every 100/sup 0/C-increase of the temperature of preheated air. The practical temperatures are significantly lower than the theoretical ones. The ceramic calciner is provided with a two-stage burner for 1600 to 1800/sup 0/C which can use also the oxygen-riched air. The glass melting furnace is operated at 1500/sup 0/C and the flat flame burner is used for a single kiln. A stabilizing burner is used for reducing ...
1987-12-05
The crack of harden cement paste observed with multi-technique
British Library Electronic Table of Contents (United Kingdom)
The shrinkage of the cement paste with low water-cement ratio at different relative humidity was observed and analyzed with ESEM and deformation map technique. The crack morphology was observed with different magnification with SEM and FESEM, and the formation of the crack was observed with AFM between two C-S-H nano particles. The observation by multi technique at multi scale indicated that the shrinkage was increase with the decrease of the humidity due to the increase of the pressure of the capillary pressure, the morphology of the crack in smaller scale was similar to that in the bigger scale, the smaller crack distributed in the latticework of the bigger ones, and the crack propagated along the gap between two nano particles of C-S-H with weaker bonding.
2010-01-01
Stress analysis of hydride bed vessels used for tritium storage
Energy Technology Data Exchange (ETDEWEB)
A prototype hydride storage bed, using LaNi{sub 4.25}Al{sub 0.75} as the storage material, was fitted with strain gages to measure strains occurring in the stainless steel bed vessel caused by expansion of the storage powder upon uptake of hydrogen. The strain remained low in the bed as hydrogen was added, up to a bed loading of about 0.5 hydrogen to metal atom ratio (H/M). The strain then increased with increasing hydrogen loading ({approximately} 0.8 H/M). Different locations exhibited greatly different levels of maximum strain. In no case was the design stress of the vessel exceeded.
1991-01-01
International Nuclear Information System (INIS)
The read/write characteristics for perpendicular magnetic recording media of focused-ion-beam (FIB)-etched recording heads were investigated. It was found that the trailing edge of an FIB-etched head produces a higher gradient in the magnetic field perpendicular to the medium than a head which has not been etched. The signal-to-noise ratio of the medium increased with the FIB-etched write gap. A high-Bs and thin pole increased the magnetic field's gradient in the perpendicular direction, resulting in excellent read/write characteristics.
2001-10-01
Nature of low-energy antiprotons in cosmic rays
Energy Technology Data Exchange (ETDEWEB)
A model of formation of cosmic ray antiproton spectrum in plasma consisting mainly of electron-positron pairs (nsub(+-)/nsub(p) > or approximately 10) is considered. Additional energy losses due to Coulomb collisions in plasma provide significant increase of the antiproton flux in the energy range < or approximately 1 GeV. Calculated anti p/p ratio is in a satisfactory agreement with the observational data.
1983-02-01
Energy Technology Data Exchange (ETDEWEB)
Different sized ROIs within the femoral head and different modes of calculation were used in (/sup 99m/Tc)MDP scintimetry after femoral neck fracture. In preoperative scintimetry, correction for increased trochanteric uptake gave the best discrimination, whereas in postoperative scintimetry the direct ratio fractured/intact femoral head was superior. The change in ROI size had little influence.
1985-04-01
Activated wood charcoal from rubber plants
Energy Technology Data Exchange (ETDEWEB)
The conditions for the production of activated charcoal having a decolorization power (DP) of less than 160 mL/g for methylene blue solutions from the wood of rubber plants were activation temperature of 1000 degrees, rentention time of 30 minutes, and steam-char-ratio of approximately 1.7. The installation of a side-burner around the rotary kiln to decrease the temperature gradient increased the DP of the activated charcoal to 190-200 mL/g without a decrease in yield.
1982-01-01
Energy Technology Data Exchange (ETDEWEB)
As part of a five-year-lasting open-top-chamber experiment at the `Edelmannshof` site (Welzheimer Wald) we analyzed Norway spruce trees (Picea abies (L.) Karst.) with regard to carbohydrate and energy (ATP/ADP ratio) metabolism. End products, intermediates, and a regulator of carbon allocation (starch, sucrose, hexoses, fructose-2,6-bisphosphate) as well as enzyme activities involved in sucrose metabolism (sucrose-P synthase, sucrose synthase, acid invertase) were determined in needle and trunk samples of the different treatments (charcoal-filtered, unfiltered, ambient air). Changes of these parameters were documented annually and with regard to needle development (up to 2 years after bud break), and diurnally during an ozone period in midsummer. Samples from trees grown in an unfiltered atmosphere showed relatively high sucrose and hexose contents of the needles. The capacities of sucrose-P synthase (increased; sucrose synthesis) and acid ...
1997-12-01
Rb-Sr isotope systematics of granitic soil chronosequence: The importance of biotite weathering
Energy Technology Data Exchange (ETDEWEB)
The Rb-Sr isotope systematics of bedrock, soil digests, and the cation exchange fraction of soils from a granitic glacial soil chronosequence in the Wind River Mountains, Wyoming, USA, were investigated. Six soil profiles ranging in age from 0.4 to {approximately}300 kyr were studied and revealed that the {sup 87}Sr/{sup 86}Sr ratio of exchangeable strontium in the B-horizons decreased from 0.7947 to 0.7114 with increasing soil age. Soil digests of the same samples showed much smaller variation in {sup 87}Sr/{sup 86}Sr from 0.7272 to 0.7103 and also generally decreased with increasing soil age. Elevation of the {sup 87}Sr/{sup 86}Sr ratios of Sr released by weathering over the soil digest and bedrock values results from the rapid weathering of biotite to form hydrobiotite and vermiculite in the younger soils. Biotite is estimated to weather at approximately eight times the rate of plagioclase (per gram ...
1997-08-01
Energy Technology Data Exchange (ETDEWEB)
The ultrafine fibers based on the composites of polyethylene terephthalate (PET) and a series of fatty acids, lauric acid (LA), myristic acid (MA), palmitic acid (PA), and stearic acid (SA), were prepared successfully via electrospinning as form-stable phase change materials (PCMs). The morphology and thermal properties of the composite fibers were studied by field emission scanning electron microscopy (FE-SEM) and differential scanning calorimetry (DSC), respectively. It was found that the average fiber diameter increased generally with the content of fatty acid (LA) in the LA/PET composite fibers. The fibers with the low mass ratio maintained cylindrical shape with smooth surface while the quality became worse when the mass ratio is too high (more than 100/100). Moreover, the latent heat of the composite fibers increased with the increase of LA content and the phase transition ...
2008-11-15
Energy Technology Data Exchange (ETDEWEB)
The purpose of this study is to identify the radiative heat transfer augmentation by a coaxial cylinder introduced in the infinite cylindrical pipe enclosing a participating gas. The gas is either a mixture of water vapor and carbon dioxide or gray. The gas is assumed to be homogeneous at a constant temperature, and has a refractive index of unity. All of the surfaces are opaque and gray, diffusely emitting and reflecting at a constant temperature. The effect of system diameter, diameter ratio, wall emittances, gas and surface temperatures, mixture component on heat transfer augmentation are studied by using the zone method with participating gas radiative properties evaluated from the weighted sum of gray gases model. From the radiative equilibrium condition, the installed wall temperature is formulated and calculated by the iteration method. If the medium is a gray gas, the augmentation observed are negligible. For the range of values studied for a real gas, if ...
1992-10-01
Silanization of the silica gel surface in the synthesis of silica gel polyamine composites uses (chloropropyl)-trichlorosilane (CPTCS). It is possible to substitute a molar fraction of reagent CPTCS with methyltrichlorosilane (MTCS), creating a mixed silane surface layer. Two types of silica gels were modified with a series of MTCS:CPTCS molar ratios. Solid-state CP/MAS 29Si and 13C NMR spectroscopies were used to evaluate the surface silane composition. Surface silane coverage was markedly improved for the resulting gels. When polyamines were grafted to the resultant MTCS:CPTCS silane layers, it was shown that the decrease in the number of propyl attachments to the polyamine resulted in increased quantities of ''free amines''. Optimum MTCS:CPTCS ratios were determined for three polyamines grafted onto one silica gel. A substantial free amine increase was observed for ...
2006-09-13
Energy Technology Data Exchange (ETDEWEB)
Silanization of the silica gel surface in the synthesis of silica gel polyamine composites uses (chloropropyl)-trichlorosilane (CPTCS). It is possible to substitute a molar fraction of reagent CPTCS with methyltrichlorosilane (MTCS), creating a mixed silane surface layer. Two types of silica gels were modified with a series of MTCS:CPTCS molar ratios. Solid-state CP/MAS 29Si and 13C NMR spectroscopies were used to evaluate the surface silane composition. Surface silane coverage was markedly improved for the resulting gels. When polyamines were grafted to the resultant MTCS:CPTCS silane layers, it was shown that the decrease in the number of propyl attachments to the polyamine resulted in increased quantities of ''free amines''. Optimum MTCS:CPTCS ratios were determined for three polyamines grafted onto one silica gel. A substantial free amine increase was observed for ...
2006-09-13
Predatory senescence in ageing wolves
British Library Electronic Table of Contents (United Kingdom)
Abstract It is well established that ageing handicaps the ability of prey to escape predators, yet surprisingly little is known about how ageing affects the ability of predators to catch prey. Research into long-lived predators has assumed that adults have uniform impacts on prey regardless of age. Here we use longitudinal data from repeated observations of individually-known wolves (Canis lupus) hunting elk (Cervus elaphus) in Yellowstone National Park to demonstrate that adult predatory performance declines with age and that an increasing ratio of senescent individuals in the wolf population depresses the rate of prey offtake. Because this ratio fluctuates independently of population size, predatory senescence may cause wolf populations of equal size but different age structure to have d...
2009-01-01
Method of manufacture of blast furnace cokes containing substantial amounts of low grade coals
Blast furnace coke containing low grade coal in a high blending ratio is manufactured by a method which comprises blending not less than 60% of a blended coal having an adjusted total moisture content of not more than 4% with not more than 40% of briquettes and carbonizing the resultant mixture. The blended coal consists essentially of not less than 80% of coking coal and not more than 20% of low grade coal. When coking coal of a kind which has its coking property segregated according to its grain size distribution is pulverized and classified by sifting and the portion of fine particles is used as mixed with the coking coal, the blending ratio of the low grade coal in the blended coal can be increased to up to 35%. The briquettes consist essentially of not less than 10% of coking coal and not more than 90% of low grade coal.
1982-03-09
Measurement of the ratio of liquid to solid phases in a continuous ingot
International Nuclear Information System (INIS)
A radiometric method of measuring the ratio of liquid and solid phases (crust thickness) in a continuous ingot for automation of the continuous steel casting process, has been proposed. The essence of the method is, that radiation flux, bearing information on the object tested, is transformed in a succession of electric pulses, which is processed afterwords for obtaining necessary information. In this case either the flux of non-scattered radiation, passed through the object, or the flux of single-scattered radiation reflected from the object is registered. Block-diagram and specifications of a radiometric device with the Co source of 50 gxequiv. Ra activity developed for this purpose are presented. The technique for calibration ob the device and the results of its tests, are described. It is shown, that introduction of such devices for the control crust thickness at the installations of continuous steel casting of metallurgical works would permit to exercise ...
Decreased semen quality in a male infected with malaria.
A 33-year-old male of proven fertility suffered six attacks of malaria while resident in an African country. For this he received anti-malarial drugs. Semen analysis performed after the fourth attack, and repeated during the following 2 years after his return to Israel, revealed severe oligozoospermia, necrozoospermia and occasionally even azoospermia. Immunological examination of the patient revealed an inverse ratio of T-cell subsets and mast cell degranulation in response to palludrin. Twenty-five months after the last attack of malaria a significant improvement was found in semen quality and there was an increase in the ratio of T-helper to T-suppressor cytotoxic cells. These observations indicate that although malaria and its treatment may affect spermatogenesis, recovery may be expected eventually. PMID:3500921
1987-10-01
British Library Electronic Table of Contents (United Kingdom)
In this context, the bulk ratio of CH4/N2 is examined as a potential alternative geochemical parameter for the assessment of thermal maturity of natural gas and compared to other previously published data. Open-system non-isothermal pyrolysis of low-mature coal from the Manjiaer sag, Tarim basin, yielded generation curves for methane and nitrogen. Analysis of the change of vitrinite reflectance indicates a two-stage process of thermal maturation with increasing temperatures. The relationship between Ro and pyrolysis temperature could be expressed by the following equations: Stage I: Ro = 0.0014T + 0.109, r = 0.9931(Ro Ro = 0.0067T -1.5855, r = 0.9996 (Ro > 0.6%). A kinetic interpretation of the characteristics of nitrogen and methane generation in humic coal during laboratory pyrolysis ind...
2008-01-01
Augmentation of laminar flow and heat transfer in flat tubes by means of helical screw-tape inserts
British Library Electronic Table of Contents (United Kingdom)
The heat transfer a characteristics and friction factor in the horizontal double pipes of flat tubes with full length helical screw element of different twist ratio and helical screw inserts with different spacer length are investigated. Cold and hot water are used as working fluid in tube side and shell side respectively. The experiments covered a range of Reynolds numbers 5.7x102Re1.31x103. The effect of spacer length on the heat transfer augmentation and friction factor and the effect of twist ratio on heat transfer augmentation and friction factor have been presented separately. The study shows that, the Nusslet number (Nu) and friction factor (f) decrease with the increase of S or Y for flat tube. The comparison between the data of present plain circular with that of previous plain ci...
2011-01-01
International Nuclear Information System (INIS)
In the heat exchangers of power plants, scale deposition may occur, especially at the leading edge of contraction. The growth of scale can lead to an increase in pressure and cause oscillation of the water level. In our previous study, the dependence of flow on contraction geometry was analyzed numerically and empirically. It was shown that the contraction ratio of hydraulic diameter of the flow path contributed greatly to the difference in pressure drop and turbulent kinetic energy at the leading edge of the flow path. In this study, the effect of contraction geometry and flow rate on scale adhesion was studied in AVT chemistry at 270degC using a high-velocity scale-adhesion test loop. The differential pressure and the amount of scale deposited due to scale adhesion at the leading edge of the flow path increased more in a quatrefoil-type flow path than in drill-type flow path. The differential pressure and the amount of ...
1999-05-01
Where the sun does not shine: Is sunshine protective against melanoma of the vulva?
British Library Electronic Table of Contents (United Kingdom)
Intermittent sun exposure and sunburn are strong predictors of cutaneous malignant melanoma (CMM). On the other hand, melanomas may arise also in non-sun-exposed areas such as the vulva. However, little is known about a possible relationship between sun exposure and vulvar melanoma. Temporal and latitudinal dependencies of the incidence rates of vulvar melanoma were studied in comparison with those of CMM among Caucasians in Sweden, East Germany, USA and Victoria (Australia). The ratios of vulvar melanoma incidence rates to those of CMM tend to decrease with increasing CMM rates. The incidence rates of CMM have increased with time until recently, while those of vulvar melanoma have either decreased or remain constant. In USA vulvar melanoma incidence rates seem to increase from south to no...
2010-01-01
The carbon fiber surface treatment and addition of PA6 on tensile properties of ABS composites
British Library Electronic Table of Contents (United Kingdom)
In this study acrylonitrile-butadiene-styrene (ABS) terpolymer was reinforced with HNO3-treated short carbon fibers (HCFs). The effects of HCF concentration on the tensile properties of the composites were examined. Increasing the HCF concentration in the ABS matrix from 10 wt% to 30 wt% resulted in improved tensile strength and tensile modulus. To obtain a strong interaction at the interface, polyamide-6 (PA6) at varying concentrations was introduced into the ABS/10 wt% HCF composite. The incorporation and increasing amount of PA6 in the composites increased tensile properties of the ABS/PA6/HCF systems due to the improved adhesion at the interface, which was confirmed by the ratio of tensile strength as an adhesion parameter. These results were also supported by scanning electron microgr...
2011-01-01
On the premixed combustion in a direct-injection diesel engine
Energy Technology Data Exchange (ETDEWEB)
The factors influencing premixed burning and the importance of premixed burning on the exhaust emissions from a small high-speed direct-injection diesel engine were investigated. The characteristics of premixed and diffusion burning were examined using a single-zone heat-release analysis. The mass of fuel burned in premixed combustion was found to be linearly related to the product of engine speed and ignition-delay time and to be essentially independent of the total amount of fuel injected. Accordingly, the premixed-burned fraction increased with increasing engine speed, with decreasing fuel-air ratio and with retarding injection timing. The hydrocarbon emissions did not correlate well with the premixed-burned fraction. In contrast, the oxides of nitrogen emissions were found to increase with decreasing premixed-burned fraction, indicating that diffusion burning, and not premixed burning, is the ...
1987-04-01
Decontamination factor of an incinerator for radioactive solid wastes
International Nuclear Information System (INIS)
An incinerator for the treatment of low-level radioactive solid wastes was installed in Tokai Research Establishment, JAERI, 1966. The incinerator was equipped with a scrubber, cyclone, electrostatic precipitator and HEPA filter. The retention factor (R.F.) of the furnace as well as the decontamination factors (D.F.) of each dust collector were measured using "3"2P as a tracer under various conditions. It was found that the overall D.F. of the incinerator was improved by the increase of the temperature in the furnace, decrease of the off gas flowrate, increase of the charged voltage of the electrostatic precipitator and by the increase of the liquid gas ratio of the scrubber. The overall D.F. of the incinerator (including the R.F. in the furnace) on the standard operating conditions was 9.1x10"6. (auth.).
Alkaline treatment of biomass fly ash for reactive dye removal from aqueous solution
British Library Electronic Table of Contents (United Kingdom)
Biomass fly ash was treated with alkaline solution to enhance its adsorption capacity of Reactive Black 5 dye. The results revealed that the alkaline concentration, solution to fly ash ratio, treatment temperature and treatment time had a positive effect on the dye adsorption capacity of the treated fly ash (TFA), due to dissolving SiO2 and increasing the proportion of unburned carbon. In addition, the dye adsorption behavior of the TFA in aqueous solution was investigated. The effects of various experimental parameters (initial pH, initial dye concentration and contact time) were determined spectrophotometrically. The dye adsorption capacity of the TFA was maximized at an alkaline pH (8.2-10.4). The adsorption capacity of dye by the TFA increased with increasing initial dye concentration....
2010-01-01
Quantitative assessment of bone scintigraphy in the hip joint disease
International Nuclear Information System (INIS)
Quantitative assessment of bone scintigraphy was performed in fifty-six patients with hip joint disease including femoral neck fracture, aseptic necrosis of the femoral head, traumatic dislocation of the hip, Perthes disease, and transient synovitis of the hip. In the static study, bone scintigraphy was obtained 3 hours after injection of sup(99m)Tc-MDP by gamma camera equipped with a computer and uptake ratios were calculated. In the dynamic study, bone scintigraphy was performed in one, 3 and 5 hours after injection of radionuclide. Femoral head uptake ratio was markedly decreased in osteonecrosis following femoral neck fracture and characteristically increased in aseptic necrosis of the femoral head but prolonged retention of sup(99m)Tc-MDP could be observed. Uptake ratios of epiphysis were decreased in Perthes disease but normal in transient synovitis of the hip. Static and dynamic study of bone ...
Interfaces in aquatic ecosystems: Implications for transport and impact of anthropogenic compounds
Energy Technology Data Exchange (ETDEWEB)
Mechanisms that govern transport, accumulation and toxicity of persistent pollutants at interfaces in aquatic ecosystems were the foci of this thesis. Specific attention was paid to humic substances, their occurrence, composition, and role in exchange processes across interfaces. It was concluded that: The composition of humic substances in aquatic surface microlayers is different from that of the subsurface water and terrestrial humic matter. Levels of dissolved organic carbon (DOC) in the aquatic surface microlayer reflect the DOC levels in the subsurface water. While the levels and enrichment of DOC in the microlayer generally show small variations, the levels and enrichment of particulate organic carbon (POC) vary to a great extent. Similarities exist between aquatic surface films, artificial semi-permeable and biological membranes regarding their structure and functioning. Acidification and liming of freshwater ecosystems affect DOC:POC ratio and humic ...
1996-11-01
Energy Technology Data Exchange (ETDEWEB)
Coal direct chemical looping (CDCL) substitutes the gasification process in syngas chemical looping (SCL), thus eliminating the need for higher oxygen consumption. In this study, operating conditions are assessed for CDCL and SCL, directed towards hydrogen production from coal. The main objective is to increase the overall H{sub 2}/CO{sub 2} ratio for a given amount of coal, based on the various conditions. The operating variables considered as part of a resource optimization analysis include: (i) inlet conditions to the primary reactors, (ii) minimum resource requirements (air, steam and iron oxide), (iii) hydrogen-to-component ratios, and (iv) effect of coal carrier gas. The results suggest that CDCL has a higher hydrogen-to-CO{sub 2} ratio than SCL along with advantages such as low overall resource requirements (steam and air) and fewer intermediate processes. The coal carrier gas affects the ...
2009-03-15
International Nuclear Information System (INIS)
Short-lived fission gas release from fuel pellets during irradiation was investigated based on the experimental results of the gas-flow rigs irradiated in the Halden Heavy Water Reactor (HBWR). The release-to-birth (R/B) rates of short-lived fission gas were measured by means of gas-flow measurement during the irradiation experiments. Surface-to-volume (S/V) ratios of fuel pellets and diffusion coefficients of short-lived fission gas release were evaluated from the obtained (R/B) values. The increase of (S/V) ratio agreed well with the point where the fuel temperature exceeded the threshold of 1% fission gas release. This indicates that the interlinkage of fission gas bubbles occurred there. The evaluated diffusion coefficients scattered in the range between 10"-"2"3 and 10"-"1"7 m"2/s, and the effects of fuel type (UO_2 or MOX) were not clearly observed. In addition, it is likely that the restructuring effect of fuel ...
2010-07-31
A new measurement of the antiproton-to-proton flux ratio up to 100 GeV in the cosmic radiation
A new measurement of the cosmic ray antiproton-to-proton flux ratio between 1 and 100 GeV is presented. The results were obtained with the PAMELA experiment, which was launched into low-earth orbit on-board the Resurs-DK1 satellite on June 15th 2006. PAMELA is equipped with a silicon-microstrip magnetic spectrometer and a silicon-tungsten imaging calorimeter and has been collecting data since July 2006. During 500 days of data collection a total of about 1000 antiprotons have been identified, including 100 above an energy of 20 GeV. The high-energy results are a ten-fold improvement in statistics with respect to all previously published data. The antiproton-to-proton flux ratio increases smoothly with energy up to about 10 GeV, in agreement with previous experiments, and then levels off. The data follow the trend expected from secondary production calculations and significantly constrain contributions from exotic sources, ...
2008-01-01
High volume fly ash RCC for dams - I : mixture optimization and mechanical properties
Energy Technology Data Exchange (ETDEWEB)
Roller compacted concretes (RCC) were developed for the Norwegian Skjerka hydropower project. RCCs were developed to have a high-volume fly ash content to address environmental issues, including the reduction of carbon dioxide emissions associated with dam construction. They also makes good use of waste product and conserve natural resources. This study examined a series of mixtures to determine the appropriateness of using RCC as a competing alternative to the traditional rock fill dam proposed for the Skjerka hydropower project. The main advantage of RCC is speed, allowing a relatively large dam to be constructed in just one summer season, saving financial costs and providing early return on the investment. In addition, fly ash can be used in the structure, using clean and renewable energy. Several procedures to proportion RCC mixtures were proposed, including the optimal paste volume method which is based on the assumption that an optimal RCC should have just enough paste to fill ...
2001-07-01
Energy Technology Data Exchange (ETDEWEB)
Signal-to-noise-ratio (SNR) thresholds for microarray data analysis were experimentally determined with an oligonucleotide array that contained perfect match (PM) and mismatch (MM) probes based upon four genes from Shewanella oneidensis MR-1. A new SNR calculation, called signal to both standard deviations ratio (SSDR) was developed, and evaluated along with other two methods, signal to standard deviation ratio (SSR), and signal to background ratio (SBR). At a low stringency, the thresholds of SSR, SBR, and SSDR were 2.5, 1.60 and 0.80 with oligonucleotide and PCR amplicon as target templates, and 2.0, 1.60 and 0.70 with genomic DNA as target templates. Slightly higher thresholds were obtained at the high stringency condition. The thresholds of SSR and SSDR decreased with an increase in the complexity of targets (e.g., target types), and the presence of background DNA, and a ...
2008-03-06
The effect of elevated carbon dioxide on a Sierra-Nevadan dominant species: Pinus ponderosa
Energy Technology Data Exchange (ETDEWEB)
The impact of increasing atmospheric C0{sub 2} has not been fully evaluated on western coniferous forest species. Two year old seedlings of Pinusponderosa were grown in environmentally controlled chambers under increased C0{sub 2} conditions for 6 months. These trees exhibit morphological, physiological, and biochemical alterations when compared to our controls. Analysis of whole plant biomass distribution has shown no significant effect to the root to shoot ratios, however needles subjected to elevated C0{sub 2} exhibited an increased overall specific needle mass and a decreased total needle area. Morphological changes at the needle level included decreased mesophyll to vascular tissue 91 ratio and variations in starch storage in chloroplasts. The elevated CO{sub 2} increased internal CO{sub 2} concentrations and assimilation of carbon. Biochemical assays ...
1995-01-01
Extracting energy from hydraulically-fractured geothermal reservoirs
The governing equations for heat and mass transfer were derived for hydraulically fractured geothermal reservoirs. When converted to nondimensional form it was shown that the equations can be considerably simplified. The resulting equations can be strongly influenced by the effects of buoyancy; the magnitude of the effect is measured by the ratio of the Grashof and Reynolds numbers, and the ratio of the actual permeability of the fracture and the square of the fracture gap width. Significant quantities of energy can be extracted from hydraulic fractures--even without thermal stress fracturing. The amount is limited by the size of the fracture and the low thermal conductivity of rock. The viscous pressure drop in open fractures is insignificant, and depending upon losses in piping and surface equipment, the entire system could be ''self-pumped'' due to buoyancy. Thermal contraction of the rock tends to ...
1976-01-01
Electrical resistivity and thermal expansion coeffcient of carbon-black-filled compounds around T_g
International Nuclear Information System (INIS)
A Michelson interferometer and a CCD detector were used to measure the number of interference fringes related to the expansion length of rubber sample. The sample was situated in a microcryostat, and the temperature of the sample was varied from -200 .deg. C to +80 .deg. C. Various types of carbon black filled rubber (Duradene, Sn-SSBR) samples were used to determine the glass transition temperatures (T_g) and the thermal coeffcients (#alpha#). The mixing ratio was 0, 10, 30, 40, 50, or 70 parts per hundred of carbon black to Sn-SSBR rubber. For the unfilled rubber of Sn-SSBR, the T_g was about -24 .deg. C, and the thermal coeffcient was 1.18 X 10"-"4 .deg. C"-"1. The thermal coeffcients sharply increased around T_g for all samples, and decreased with increasing doping ratio of carbonblack from 0 .deg. C to 30 .deg. C. The volume resistivity was measured for natural rubber and EPDM rubber. They had ...
2004-04-01
International Nuclear Information System (INIS)
In general, over the course of the time, the phenomenon of acceleration in physical development may be observed, i.e. the children and adults of the next generation are taller and heavier than in former generation. Our data presented in this paper show a regular trend of acceleration in the development on Vietnamese, but the trend is still slow and was mostly probably influenced by our difficulties in a long time of war. It is hoped that, the acceleration in the development may be increased in the future following the economical acceleration of our country, however it is known that the ratio between the length of different parts of human body is a specific characteristic for human race, sex and group age. Therefore we may estimate these ratio for the prolongation of the utilization of our measured physical data. The result of studies on water balance of Vietnamese living in comfortable environment air temperature conditions ...
1998-02-01
Analysis of natural convection in narrow annular gaps of LMFBR
International Nuclear Information System (INIS)
The natural convection characteristics of gas in a vertical narrow annular gap which had its bottom opened to high temperature fluid and its upper shielding exposed to low temperature sealant have been evaluated from simulated fluid experiments using water and from calculations using the three-dimensional thermal hydraulic analysis computer code THERVIS-III. The following results were obtained: (1) The critical Rayleigh number which represented the limit of convection generation increased as the aspect ratios #epsilon#_1 (height/circumference) and #epsilon#_2 (height/gap distance) increased. (2) The flow pattern along the circumferential direction was seen to depend more strongly on the radiant heat from the side wall, rather than the aspect ratios #epsilon#_1 and #epsilon#_2. (3) The temperature difference along the circumferential direction in the annular gap obtained from the calculation code ...
A MODEL OF THE SPECTRAL EVOLUTION OF PULSAR WIND NEBULAE
International Nuclear Information System (INIS)
We study the spectral evolution of pulsar wind nebulae (PWNe) taking into account the energy injected when they are young. We model the evolution of the magnetic field inside a uniformly expanding PWN. Considering time-dependent injection from the pulsar and coolings by radiative and adiabatic losses, we solve the evolution of the particle distribution function. The model is calibrated by fitting the calculated spectrum to the observations of the Crab Nebula at an age of a thousand years. The spectral evolution of the Crab Nebula in our model shows that the flux ratio of TeV #gamma#-rays to X-rays increases with time, which implies that old PWNe are faint in X-rays, but not in TeV #gamma#-rays. The increase of this ratio is because the magnetic field decreases with time and is not because the X-ray emitting particles are cooled more rapidly than the TeV #gamma#-ray emitting particles. Our spectral ...
2010-06-01
Results and recommendations from studies of basic handling characteristics of solid biomass fuels
Energy Technology Data Exchange (ETDEWEB)
Main results are summarised for a project carried out with the aim of increasing the knowledge of relations between handling characeristics and properties such as moisture content, particle size and shape etc. Handling characteristics that were studied: angle of repose, friction between fuel and different surfaces, the fuel`s tendency to bridge across openings, and its freezing characteristics. Some forty solid biomass fuels were studied, mainly wood fuels, with particle sized from 1 to 200 mm. New methods were developed for measurement of bridging across openings and freezing characeristics. The angle of repose varied between 25 and 55 deg. The particle shape had a significant influence, a high ratio of length/thickness gave a high angle of repose. When the fuel moisture content was increased the angle of repose first increased, then decreased, and finally increased again. The ...
1996-12-31
The present study investigates the effect of the shear rate-dependent thermal conductivity of non-Newtonian fluids on the heat transfer enhancement in a pipe flow. The constant heat flux as thermal boundary condition was adopted in the thermally developed region. The present analytical results show the heat transfer enhancement over those of a shear rate-independent thermal conductivity fluid. The heat transfer coefficient ratio (h/h{sub 0}) linearly increase with the non-dimensional average velocity difference which is the product of the shear rate-dependence of the thermal conductivity and wall-shear rate.
1996-09-01
THE DISAPPEARING NUTRITIONAL BIAS AGAINST CHINESE GIRLS
British Library Electronic Table of Contents (United Kingdom)
This paper investigates whether China has reached postnatal nutrient intake equality between boys and girls, despite an exceptionally high ratio of boys to girls at birth, after dramatic technological advances in prenatal sex determination, rapid increases in income, and improved educational opportunities for females. Dominance methods applied to data from the Chinese Health and Nutrition Surveys (selected years 1991-2004) reveal no bias in calorie consumption between girls and boys. We find some weak evidence of protein bias toward boys in 1991, but it disappeared by 2004. (JEL I32, O15, N35)
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
By applying the mass, momentum, and angular momentum conservation laws and the maximum flow rate principle to swirling, effectively inviscid, incompressible flows in a circular tube with a sudden expansion and the direct-flow and reversed-flow Borda mouthpieces the dependence of the flow rate coefficient and mechanical energy losses on the radius ratio and nondimensional circulation is obtained. Several calculating approaches with potential and helical motion are introduced and investigated. In the case of helical motion, as the swirl decreases the axial core of the flow is found to close with a sudden change of the flow parameters.
1994-11-01
Damage mechanism in high temperature fatigue of alloy 800 H
Energy Technology Data Exchange (ETDEWEB)
In order to investigate the influence of grain boundary cavities on the life time of Alloy 800 H various fatigue tests have been performed at 800/sup 0/C. Cavity formation has been observed only in asymmetrical tests. Compared to the corresponding symmetrical tests, the cyclic life time is shorter. As the cavitation damage increases, the ratio of life times in vacuum and in air steadily decreases from an initial value of 5. In extreme cases it can reach a value close to 1. In this case, cavitation damage dominates over the usual damage mechanism, which is cracks from the surface.
1986-09-01
Energy Technology Data Exchange (ETDEWEB)
There is increasing demand to functionalize meso- and nano-porous materials by coating and make the porous substrate biocompatible or environment friendly. However, coating on a meso-porous substrate poses great challenges, especially if the pore aspect ratio is high. In the current work the pulsed laser deposition (PLD) method is used for coating Ni{sub 3}Al-based meso-porous membranes with diamond-like carbon (DLC) layers of high thickness homogeneity and adhesion. (orig.)
2008-08-15
International Nuclear Information System (INIS)
A series of Model Tests of Embedment Effect on Reactor Buildings has been carried out by the Nuclear Power Engineering Corporation (NUPEC), under the sponsorship of the Ministry of International Trade and Industry (MITI) of Japan. Seismic response of an embedded reactor building is greatly affected by the non-linearity of the backfill soil. However, quite few experimental data have been obtained so far. The objective of this study is to qualitatively evaluate the non-linear behavior of the backfill soil through shaking table tests. Its effects to the seismic response of a reactor building constructed at a soft rock site can be made clear through the tests. Non-linear effects of the backfill soil on the seismic response of the embedded reactor building model were evaluated experimentally. Based on the sinusoidal and seismic wave excitation tests, the following conclusions were obtained regarding the changes in vibrational characteristics of the building model which occurred according to ...
1993-08-15
Investigation by XRF and XRD of Zn and Fe in Fe{sub x} Zn{sub 1-x} thin films
Energy Technology Data Exchange (ETDEWEB)
Fe{sub x}Zn{sub 1-x} alloys were electrochemically deposited on aluminum substrates from a sulfate bath. The K{beta}/K{alpha} x-ray intensity ratios of Zn and Fe in Fe{sub x}Zn{sub 1-x} thin films have been experimentally studied. The energy dispersive x-ray fluorescence (EDXRF) technique was used to measure K x-ray photons. Samples were excited by using 59.5 keV photons emitted by a 50 mCi {sup 241}Am radioactive source. The emitted K x-rays were detected by an Ultra-LEGe detector having a resolution of 150 eV at 5.9 keV. In addition, the effect of bath composition on the phase structure was investigated by x-ray diffraction (XRD) analysis. The composition of the thin films was analyzed by atomic absorption spectrometry analysis. Iron content was shown to strongly affect the structure of Zn-Fe alloys. It was found that the K-shell x-ray intensity ratio changed in Fe{sub x}Zn{sub 1-x} thin films for different values of x. The reason for this ...
2008-12-15
Investigation by XRF and XRD of Zn and Fe in Fex Zn1-x thin films
International Nuclear Information System (INIS)
FexZn1-x alloys were electrochemically deposited on aluminum substrates from a sulfate bath. The K?/K? x-ray intensity ratios of Zn and Fe in FexZn1-x thin films have been experimentally studied. The energy dispersive x-ray fluorescence (EDXRF) technique was used to measure K x-ray photons. Samples were excited by using 59.5 keV photons emitted by a 50 mCi 241Am radioactive source. The emitted K x-rays were detected by an Ultra-LEGe detector having a resolution of 150 eV at 5.9 keV. In addition, the effect of bath composition on the phase structure was investigated by x-ray diffraction (XRD) analysis. The composition of the thin films was analyzed by atomic absorption spectrometry analysis. Iron content was shown to strongly affect the structure of Zn-Fe alloys. It was found that the K-shell x-ray intensity ratio changed in FexZn1-x thin films for different values of x. The reason for this change may be that the electronegativity of iron is ...
2008-12-01
Energy Technology Data Exchange (ETDEWEB)
Experimental investigations were performed to assess the effects of different shaped obstructions on flame propagation in a rectangular confinement, 235 mm in height, with a 1000 x 950mm cross section and a large top-venting area of 1000 x 320mm. Four different single obstacles were used: rectangular, cylindrical, triangular, and square cross-sections with blockage ratios of 5 and 10%. Temporally resolved flame front images were recorded by a high-speed video camera to investigate the interaction between a propagating flame and the obstacle. The local flame displacement speeds and their probability density functions (pdfs) were obtained for the different obstacles. Before the freely propagating flame impinges on the obstacle, the flame propagation speed remains close to the laminar burning velocity, regardless of the obstacles used. As the propagating flame impinges on the obstacle, the local propagation speed increases due to the expansion of ...
2007-07-15
Vacuum distillation refining and recycling of magnesium alloys
Energy Technology Data Exchange (ETDEWEB)
Purification parameters of the vacuum distillation process for AM50A and AZ31B magnesium alloy were studied. The vacuum distillation tests were kept at 580 C to 620 C up to 10 h under a vacuum pressure of about 1 Pa. The purification ratio for AM50A magnesium alloy increases with increasing the purification time. The chemical compositions of materials deposited purifying at 580 C for AM50A magnesium alloy almost satisfy the values for pure magnesium specified by JIS standard specification. The chemical compositions of deposited materials at 600 C for AZ31B magnesium alloy satisfy the values specified by the standard specification except for Zn. (orig.)
2003-07-01
Speckle Reduction for LIDAR Using Optical Phase Conjugation
Energy Technology Data Exchange (ETDEWEB)
Remote detection of chemicals using LIDAR (Light Detection and Ranging) utilizing DIAL (Differential Absorption LIDAR) is now a standard detection technique for both military and civilian activities. We have developed a novel nonlinear optical phase conjugation system that can reduce the effects of speckle noise and atmospheric turbulence on DIAL remote detection systems. We have shown numerically and experimentally that it is possible to increase the signal-to-noise (S/N) ratio for LIDAR systems under certain conditions using optical phase conjugation. This increase in S/N can result in more accurate detection of chemical effluents while simultaneously reducing the time necessary to acquire this information.
2001-02-26
Providing better indoor environmental quality brings economicbenefits
Energy Technology Data Exchange (ETDEWEB)
This paper summarizes the current scientific evidence that improved indoor environmental quality can improve work performance and health. The review indicates that work and school work performance is affected by indoor temperature and ventilation rate. Pollutant source removal can sometimes improve work performance. Based on formal statistical analyses of existing research results, quantitative relationships are provided for the linkages of work performance with indoor temperature and outdoor air ventilation rate. The review also indicates that improved health and related financial savings are obtainable from reduced indoor tobacco smoking, prevention and remediation of building dampness, and increased ventilation. Example cost-benefit analyses indicate that many measures to improve indoor temperature control and increase ventilation rates will be highly cost effective, with benefit-cost ratios as high as 80 and annual ...
2007-06-01
British Library Electronic Table of Contents (United Kingdom)
Water stress and fire disturbance can directly impact stand structure, biomass and composition by causing mortality and influencing competitive interactions among trees. However, open eucalypt forests of southwest Australia are highly resilient to fire and drought and may respond differently to increased fire frequency and aridity than forests dominated by non-eucalypt species. We measured the variation in stem density, basal area, stand biomass, sapwood area, leaf area and litterfall across 16 mixed jarrah (Eucalyptus marginata) and marri (Corymbia calophylla) forest stands along an aridity gradient in southwest Australia that had variable fire histories. Fire frequency was defined as the total number of fires over a ~30-year period and aridity as the ratio of potential evapotranspiration...
2009-01-01
Formation of O'/#beta#' sialon in the presence of yttria
International Nuclear Information System (INIS)
Synthesis of O'/#beta#' SiAlON composites was studied. As starting materials, Si_3N_4, Al_2O_3 and SiO_2 powders were used. Pressureless sintering was applied as consolidation technique and was performed at 1400-1700 C. Densification and reaction taking place during sintering were followed. Microstructure of O'/#beta#' composites is discussed. It was found that without additives liquid phase amount formed within the samples was below critically needed for full densification, but promoted reaction of O' and #beta#' formation. Using yttria as additive densification was enhanced. O'/#beta#' ratio decreased while H_V and K_I_c increased with increasing amount of additive. (orig.).
1993-10-04
Food and biomass production in small oil expression facilities
Energy Technology Data Exchange (ETDEWEB)
This paper reported on a study in which rapeseeds were separated into high quality seed for food oil and low quality seed for biofuels. A laboratory-scale oilseed screw press was then used to examine the effects of choke opening and seed preheating on the rapeseed pressing performance and the quality of food oil and biofuels oil. Oil recovery and chlorophyll content was found to increase as maximum pressure increased. In terms of pressing performance, the rapeseed heated by microwaves yielded more oil and chlorophyll than without heating. The NEB ratio of microwave heating press with an 8.0 mm choke opening was advantageous. Rapeseed oil extracted from low quality seeds was found to have a high acid value. The quality of oil extracted by oilseed screw press was found to be good and met the requirements of the Codex Alimentarius for edible oils.
2010-07-01
Energy Technology Data Exchange (ETDEWEB)
A focused ion beam (FIB) system produces a final beam spot size down to 0.1 .mu.m or less and an ion beam output current on the order of microamps. The FIB system increases ion source brightness by properly configuring the first (plasma) and second (extraction) electrodes. The first electrode is configured to have a high aperture diameter to electrode thickness aspect ratio. Additional accelerator and focusing electrodes are used to produce the final beam. As few as five electrodes can be used, providing a very compact FIB system with a length down to only 20 mm. Multibeamlet arrangements with a single ion source can be produced to increase throughput. The FIB system can be used for nanolithography and doping applications for fabrication of semiconductor devices with minimum feature sizes of 0.1 .mu.m or less.
1999-01-01
Energy Technology Data Exchange (ETDEWEB)
A focused ion beam (FIB) system produces a final beam spot size down to 0.1 {mu}m or less and an ion beam output current on the order of microamps. The FIB system increases ion source brightness by properly configuring the first (plasma) and second (extraction) electrodes. The first electrode is configured to have a high aperture diameter to electrode thickness aspect ratio. Additional accelerator and focusing electrodes are used to produce the final beam. As few as five electrodes can be used, providing a very compact FIB system with a length down to only 20 mm. Multibeamlet arrangements with a single ion source can be produced to increase throughput. The FIB system can be used for nanolithography and doping applications for fabrication of semiconductor devices with minimum feature sizes of 0.1 m or less. 13 figs.
1999-08-31
Extraction of hafnium by 1-phenyl-3-methyl-4-benzoyl-5-pyralozone from aqueous-alcoholic solutions
International Nuclear Information System (INIS)
Extraction of hafnium by 1-phenyl-3-methyl-4-benzoyl-5-pyrazolone (HL) in benzene, toluene, chloroform and tetrachloromethane from aqueous-alcoholic solutions of the formal acidity of 2M-HClO_4 was studied. Methyl, ethyl, n- and isopropyl, tert-butyl and allyl alcohol as well as ethylene glycol monomethyl ether and propylene glycol were used as organic components of the mixed aqueous-organic phase. Their presence in some cases resulted in a synergic increase in the distribution ratio of hafnium. The increase is interpreted using the results of a slope analysis and measurements of the alcohol distribution and the relative permittivity of the organic phase. It is suggested that HfL_4 molecules were solvated by alcohol molecules in the organic phase. At high alcohol concentration synergism changed into antagonism. This was caused by changes in the distribution of HL and its interaction with the alcohol in the organic phase. ...
International Nuclear Information System (INIS)
To sophisticate the nuclear fuel recycling processes, the transfer percentages for Pd, Mo, Te, and Sb should be determined. Each element solution containing NaNO_3 or HNO_3 was fed consistently into the thin film evaporator regulated in vac and at 50 deg C. The analyte percentages in the inside of the lid, in the condenser, and in the distillate were 10"-"1%/m"2, 10"-"3%/m"2, and 10"-"3% (DF = 10"5), respectively. The Mo percentage in the condenser was lower by a factor of 10 than those of other elements investigated. The NO_3"- percentages were nearly constant despite increasing HNO_3 concentrations, however, the ratios decreased with increasing NaNO_3 concentrations. (author)
2003-02-01
Elastic properties, hardness and indentation fracture toughness of #beta#-sialons
International Nuclear Information System (INIS)
Dense samples of #beta#-sialons (with z from 1 to 4) were pressuressly sintered for different time (15-240 minutes) and at relatively low temperature of 1600 C using single-phase #beta#-sialon powders synthesized by combustion nitridation. The samples were characterized using ultrasonic method for determination of elastic properties (E,G,#mu#). Also, hardness by Knoop and fracture toughness by Vickers indentation microfracture method was estimated. With increasing z number Young's modulus decreases from 293 to 179 GPa. Simultaneously Poisson ratio increases by about 30%. The highest values of hardness and fracture toughness were obtained for sialon with z equal to 1. (orig.).
1993-10-04
British Library Electronic Table of Contents (United Kingdom)
The objective of this study is to analyze the effects of heat loss characterized by a percentage of the fuel's energy, friction and variable specific heats of working fluid on the performance of an air standard Otto cycle with a restriction of maximum cycle temperature. A more realistic and precise relationship between the fuel's chemical energy and the heat leakage that is based on a pair of inequalities is derived through the resulting temperature. The variations in power output and thermal efficiency with compression ratio, and the relations between the power output and the thermal efficiency of the cycle are presented. The results show that the power output as well as the efficiency where maximum power output occurs will increase with increase of the maximum cycle temperature. The temp...
2008-01-01
Effect of carrier on surface decontamination efficiency
International Nuclear Information System (INIS)
The dependence was determined of the decontamination factor ratio found in the presence of a carrier and in a carrier-free system on carrier concentration at different concentrations of a complexing agent in a solution. Bearing balls were used as contamination materials while a mixture of "1"5"2Eu and "1"5"4Eu isotopes was used as a contaminant, citric acid in a concentration of 5x10"-"3 to 1x10"-"1 mol/dm"3 as a complexing agent, and Eu, lanthanum and aluminium at a concentration range of 1x10"-"5 to 1x10"-"2 mol/dm"3 as carriers. While no increase in the decontamination factor was found for aluminium, a considerable increase was observed in the isotopic and homologic carriers and the concentration dependence of the carrier reached the maximum. An equation was derived explaining the effect by the isotope exchange between the contaminant and the carrier and by the reaction between the carrier and the complexing agent. ...
EMPLOYMENT, CAPITAL, AND PRODUCTIVITY DYNAMICS: EVIDENCE FROM THE MANUFACTURING SECTOR IN URUGUAY
British Library Electronic Table of Contents (United Kingdom)
Using a sample of Uruguayan manufacturing establishments we analyze employment, capital, and productivity dynamics over a period of currency appreciation; changes in trade policy; and changes in the institutional setting of wage negotiations. As the relative capital-labor price ratio fell, capital intensity increased. At the same time, there was an increase in labor and total factor productivity. Creation and destruction rates were relatively high and pervasive over time, sectors, establishment size, and establishment age, with exits explaining a sizeable part of destruction rates. Most of the excess reallocation was due to movements -within- rather than -between- sectors. Thus, high reallocation rates were linked to establishment-level heterogeneity rather than aggregate shocks.
2011-01-01
Drift-kink instability induced by beam ions in field-reversed configurations
Energy Technology Data Exchange (ETDEWEB)
The drift-kink instability in field-reversed configurations with a beam component is investigated by means of a three-dimensional particle simulation. The unstable mode with the toroidal mode number n=4 grows with the rate {gamma} {approx} 0.1 - 1.0{omega}{sub ci} for a strong beam current and deforms the plasma profile along the beam orbit in the vicinity of the field-null line. This mode is nonlinearly saturated as a result of the relaxation of current profile. Both the saturation level and the growth rate tend to increase as the ratio of the beam current to the plasma current I{sub b}/I{sub p} increases. It is also found that there is a threshold value of the beam velocity {upsilon}{sub b} {approx} {upsilon}{sub Ti} (ion thermal velocity) for the excitation of the instability. (author)
1999-04-01
Digital Audio Sampling for Film and Video.
Digital audio sampling is explained, and some of its implications in digital sound applications are discussed. Digital sound equipment is rapidly replacing analog recording devices as the state-of-the-art in audio technology. The philosophy of digital recording involves doing away with the continuously variable analog waveforms and turning the patterns into numbers. A digital recording device rapidly samples the incoming sounds, quantifying the signal into a series of numerical values (binary codes). Although digital sound eliminates many of the traditional analog problems, digital signal processing presents key problems in sampling rates and synchronization. Careful control is necessary to check signals through each step in the audio chain. The advantages of digital audio processing include increased signal-to-noise ratio, no flutter, transparent generation of copies, and sound manipulation. These benefits come with ...
1993-03-01
International Nuclear Information System (INIS)
Glasses in the system (95-x) [0.25 Na2O-0.75 B2O3]-x P2O5-5 Fe2O3 (0?x?15 mol%), have been prepared by the melt quenching technique. Elastic properties and FT-IR spectroscopic studies have been employed to study the role of P2O5 on the structure of the glass system. Elastic properties Poisson's ratio, micro-hardness and Debye temperature have been investigated using sound wave velocity measurements at 4 MHz (both longitudinal and shear) at room temperature. The results showed that the density and the molar volume increase as both sound velocities and the determined glass transition temperatures decrease with increasing the contents of P2O5. Infrared spectra of the glasses reveal that the borate network consists of diborate units and is affected by the increase in the concentration of P2O5 content as a second network former. These results are interpreted in terms of the replacement of the diborate units ...
2009-06-01
Energy Technology Data Exchange (ETDEWEB)
Amphiphilic block copolymers are synthesized by sulfonation of poly(styrene-b-methyl methacrylate) (PS-b-PMMA) using acetyl sulfate, and are blended with poly(vinylidene fluoride) (PVDF) to prepare a new proton exchange membrane, in which PMMA is miscible with PVDF. The morphology and the transport properties of the membranes are investigated as functions of the degree of sulfonation as well as the blend ratio. Notable transition of phase-separated morphology is observed as the PVDF content of the blend is increased. Both the proton conductivity and the ion-exchange capacity (IEC) of the membrane increase with increasing the degree of sulfonation of PS-b-PMMA, and they are also enhanced as the phase-separated domains of blend membrane are well-ordered. Unlike the Nafion membrane, the proton conductivity of the blend membrane increases up to 90 C, indicating the blend membrane shows ...
2009-03-01
Hydrogen peroxide for improving premixed methane-air combustion
Energy Technology Data Exchange (ETDEWEB)
In this study, the effects of hydrogen peroxide on laminar, premixed, methane-air flames at atmospheric pressure and temperature were investigated using CHEMKIN III and GRI 3.5 mechanism. The range of fuel/air equivalence ratio {phi} was varied from 0.6 to 1.2, and the amount of hydrogen peroxide was altered from 0% to 20% volumetric fraction of the methane-hydrogen peroxide (air excluded) mixture. The burning velocity was found to increase with increasing hydrogen peroxide addition, with a relatively larger increase for the fuel-richer mixtures ({delta}S{sub u} up to 15 cm/s for {phi} {approx}=1.2). The adiabatic flame temperature rose with hydrogen peroxide addition, and the temperature rise per unit hydrogen peroxide addition was more significant ({delta}T up to 100 K) for the leaner mixtures. For the same mixture stoichiometry, adding hydrogen peroxide also increased CO ...
2005-03-01
The Rio Grande alluvial floodplain aquifer between El Paso/Juarez and Fort Quitman, Texas has been intensively tilled and irrigated since 1910. Almost since that time, the Rio Grande and its interconnected alluvial aquifer in this stream reach have been affected by excessive salinity problems. Presently, salinity of surface water and groundwater increases from 800 to 2000 mg/L total dissolved solids (TDS) near El Paso, Texas to 2500 to 5500 mg/L TDS near Fort Quitman, Texas, approximately 115 km downstream. Chloride (Cl) and Chloride/Bromide (Cl/Br) ratios increase downstream, with a marked increase in salinity beginning about 45 km below El Paso. Groundwater sampling in an intensively investigated reach of the floodplain aquifer, extending from 35 to 60 km below El Paso identified two distinct water types. The first water type (17 samples) is a relatively dilute groundwater containing 1000 to 2000 ...
2005-12-01
Heterogeneous catalytic oxidative dehydrogenation of ethylbenzene to styrene with carbon dioxide
Energy Technology Data Exchange (ETDEWEB)
Alkaline promoted active carbon supported iron catalysts are very active in the oxidative dehydrogenation of ethylbenzene to styrene in the presence of carbon dioxide. The best results were obtained at 550 C for a Li-promoted catalyst with a conversion of ethylbenzene of 75% and a selectivity towards styrene of nearly 95%. These results are better than those obtained with industrial catalysts which perform the dehydrogenation process with an excess of water. The main product of the dehydrogenation reaction with CO{sub 2} was styrene, but the following by-products were detected - benzene and toluene. The selectivity towards toluene was always higher than towards benzene. We observed also the formation of carbon monoxide and water, which were produced with a constant molar ratio of about 0.8. The weight of the catalysts increased up to 20% during the reaction due to deposition of carbon. Using a too large excess of CO{sub 2} (CO{sub 2}/EB>10) ...
1998-12-31
Energy Technology Data Exchange (ETDEWEB)
Attention deficit hyperactivity disorder (ADHD) is a psychiatric disorder in childhood that is known to be associated with dopamine dysregulation. In this study, we investigated dopamine transporter (DAT) density in children with ADHD using iodine-123 labelled N-(3-iodopropen-2-yl)-2β-carbomethoxy-3β-(4-chlorophenyl) tropane ([{sup 123}I]IPT) single-photon emission tomography (SPET) and postulated that an alteration in DAT density in the basal ganglia is responsible for dopaminergic dysfunction in children with ADHD. Nine drug-naive children with ADHD and six normal children were included in the study. We performed brain SPET 2 h after the intravenous administration of [{sup 123}I]IPT and carried out both quantitative and qualitative analyses using the obtained SPET data, which were reconstructed for the assessment of the specific/non-specific DAT binding ratio in the basal ganglia. We then investigated the correlation between the severity ...
2003-02-01
Climate controls on forest soil C isotope ratios in the southern Appalachian Mountains
Energy Technology Data Exchange (ETDEWEB)
A large portion of terrestrial carbon (C) resides in soil organic carbon (SOC). The dynamics of this large reservoir depend on many factors, including climate. Measurements of {sup 13}C:{sup 12}C ratios, C concentrations, and C:N ratios at six forest sites in the Southern Appalachian Mountains (USA) were used to explore several hypotheses concerning the relative importance of factors that control soil organic matter (SOM) decomposition and SOC turnover. Mean {delta}{sup 13}C values increased with soil depth and decreasing C concentrations along a continuum from fresh litter inputs to more decomposed soil constituents. Data from the six forest sites, in combination with data from a literature review, indicate that the extent of change in {delta}{sup 13}C values from forest litter inputs to mineral soil (20 cm deep) is significantly associated with mean annual temperature. The findings support a conceptual model of vertical ...
2000-04-01
Characteristics of meningioma scintigraphy with multiple brain imaging agents
International Nuclear Information System (INIS)
Purpose: To clarify the characteristics of meningioma scintigraphy with multiple brain imaging agents and to evaluate their roles in diagnosis of meningiomas. Methods: Blood flow, "9"9"mTc-ECD, "9"9"mTc-DTPA, and/or "9"9"mTc-MIBI brain imagings were performed in 21 patients with meningiomas (3 malignant, 18 benign) proved by surgery and pathology. CT/MRI examinations were also made within one month. Characteristics of meningioma images were analyzed and uptake ratios were calculated. Results: In 16 of 20 patients, increased radioactivity during the arterial phase in the blood flow image was seen. Concave round or oval defects with smooth contour in the cerebral cortex were observed in 17 of 19 patients with "9"9"mTc-ECD, depression of frontoparietal cortex was found in one case and no abnormality in the other. A homogeneous accumulation of radioactivity in area corresponding to the defect in "9"9"mTc-ECD image was found in 17/17 patients with ...
1998-08-01
Energy Technology Data Exchange (ETDEWEB)
This study investigated the engine performance and emissions of a supercharged engine fueled by hydrogen and ignited by a pilot amount of diesel fuel in dual-fuel mode. The engine was tested for use as a cogeneration engine, so power output while maintaining a reasonable thermal efficiency was important. Experiments were carried out at a constant pilot injection pressure and pilot quantity for different fuel-air equivalence ratios and at various injection timings without and with charge dilution. The experimental strategy was to optimize the injection timing to maximize engine power at different fuel-air equivalence ratios without knocking and within the limit of the maximum cylinder pressure. The engine was tested first with hydrogen-operation condition up to the maximum possible fuel-air equivalence ratio of 0.3. A maximum IMEP of 908 kPa and a thermal efficiency of about 42% were obtained. Equivalence ...
2010-01-15
Use of sewage sludge and coconut coir mix as a peat substitute for potted chrysanthemum
Energy Technology Data Exchange (ETDEWEB)
Recent central processing of domestic wastewater in Malaysia has initiated investigations into the disposal/utilization of the sewage sludge produced. We had conducted an experiment to investigate the feasibility of using dewatered sewage sludge and coconut coir as a peat substitute in a potting medium for chrysanthemum. The experiment involved 9 treatments with sewage sludge (SS) and coconut coir (CC) mixed in different ratios (v/v) to replace peat in the standard potting medium of 3:2:1 (soil: peat: sand).The potting medium contained the following treatments, T1: peat + recommended rates of Agroblend (Ag), a slow release fertilizer, and Grofas (Gf), a foliar fertilizer (commonly used medium and fertilization), T2: [1SS:1CC] + Ag, T3: [1SS:1CC] + half recommended rates of Agroblend and Grofas (1/2Ag + 1/2Gf), T4: [2SS:1CC] + Ag, T5: [2SS:1CC] + 1/2Ag + 1/2Gf, T6: [3SS:1CC] + Ag, T7: [3SS:1CC] + 1/2Ag + 1/2Gf, T8: [4SS:1CC] + Ag, and T9: [4SS:1CC] + 1/2Ag + 1/2Gf; ...
2003-07-01
Response of a non-Hodgkin lymphoma to "6"0Co therapy monitored by 31P MRS in situ
International Nuclear Information System (INIS)
High quality "3"1P MR spectra (signal to noise ratio (S/N) approximately 18, 15 min acquisition for each spectrum) were consistently obtained with surface coils over a period of 6-week RT. Both transient and steady state alterations in metabolites in response to RT were found in this case. The transient changes occurred during the first 3 hr immediately after the 3rd fractionated RT, these changes include the transient elevation of the PCr resonance, a decrease in PDE and an increase in intracellular pH. The monitoring showed that the metabolites approached steady state approximately 2 hr after the fractionated radiation intervention, suggesting that in vivo MRS can be useful for studying the dynamics of tumor response to RT such as repair of potential lethal damage, growth delay, and reoxygenation etc. The steady-state MR spectra showed the net response to each intervention and can clinically be useful for predicting and measuring the result ...
International Nuclear Information System (INIS)
Novel CdS hollow microspheres have been successfully synthesized via a facile template-free solution-phase reaction from cadmium nitrate and thioacetamide precursors. The morphology of CdS hollow microspheres depends strongly on the ratio between the precursors, cadmium nitrate to thioacetamide ratio. The physical properties of the hollow microspheres have systematically been studied by different characterization methods. The stoichiometry of the hollow microspheres studied by the energy dispersive X-ray diffraction spectroscopy confirmed that the synthesized CdS hollow microspheres are nearly stoichiometric bulk like CdS. The morphology of the hollow microspheres studied by high resolution scanning electron microscopy and transmission electron microscopy observations showed that the CdS hollow microspheres of the size of 2.5 ?m have hollow structure and are constructed by several nanoparticles of the size between 30 and 40 nm. The UV-visible ...
2010-12-15
Energy Technology Data Exchange (ETDEWEB)
The stoichiometry of photorespiration, S, is defined as the fraction of glycolate carbon photorespired. It is postulated that under steady-state conditions there are two determinants of the ratio of photorespiration to net photosynthesis: the partitioning of ribulose bisphosphate between oxidation and carboxylation, and the partitioning of glycolate between reactions leading to complete oxidation to CO/sub 2/ (S . 100%) and those yielding CO/sub 2/ plus serine (S . 25%). S may be calculated using two independent probes of the system. The physical probe, using an infrared gas analyzer, measured photorespiration and net photosynthesis, and hence their ratio PR/NPS . pn(phys). The metabolic probe employed tracer (3R)-D-(3-/sup 3/H1,3-/sup 14/C)glyceric acid to determine r, the fraction of /sup 3/H retained in the triose phosphates leaving the chloroplasts. It is deduced from the postulated model that S . pn(phys) . r/(1 - r). Experiments have been ...
1985-03-01
Energy Technology Data Exchange (ETDEWEB)
Changes in the phosphate metabolism of the transplanted SCCVII (squamous cell carcinoma VII) tumor were studied before and after irradiation using in vivo [sup 31]P-magnetic resonance spectroscopy (MRS). Phosphocreatine (PCr), [gamma]-, [alpha]-, [beta]-ATP, inorganic phosphate (Pi), phosphomonoester (PME), and phosphodiester (PDE) were detected in [sup 31]P-MR spectra of tumor tissues. The curve fitting method was employed for calculating each peak of [sup 31]P-MR spectra (PCr, [beta]-ATP, Pi, PME, PDE). The values of PCr, PCr/Pi, [beta]-ATP/Pi and pH decreased in proportion to the growth of tumor, whereas that of Pi, PME and PDE increased. But the changes of [beta]-ATP were minimal in degree. Based on the fact that the ratio of PCr/Pi highly correlated with tumor volume and showed the most remarkable change among various parameters, it might be the useful index for the tumor growth. Because the phospholipid metabolite PME was detected in the ...
1992-03-01
Recent developments in the design of conceptual fusion reactors
International Nuclear Information System (INIS)
Since the first round of conceptual fusion reactor designs in 1973 - 1974, there has been considerable progress in design improvement. Two recent tokamak designs of the Wisconsin and Culham groups, with increased plasma beta and wall loading (power density), lead to more compact reactors with easier maintenance. The Reference Theta-Pinch Reactor has undergone considerable upgrading in the design of the first wall insulator and blanket. In addition, a conceptual homopolar energy storage and transfer system has been designed. In the case of the mirror reactor, there are design changes toward improved modular construction and ease of handling, as well as improved direct converters. Conceptual designs of toroidal-multiple-mirror, liner-compression, and reverse-field pinch reactors are also discussed. A design is presented of a toroidal multiple-mirror reactor that combines the advantages of steady-state operation and high-aspect ratio. The ...
Rapid toxicity testing based on mitochondrial respiratory activity
Energy Technology Data Exchange (ETDEWEB)
The need exists for rapid and inexpensive methods to determine the health effects of environmental contaminants on biological systems. One of the current research approaches for assessing cytotoxicity is to monitor the respiratory activity of the mitochondrion, a sensitive, nonspecific subcellular target site. Detected changes in mitochondrial function after the addition of a test chemical could be correlated to toxic effects. Mitochondrial respiration can be characterized by three indices: state 3 and state 4 respiratory rates, and the respiratory control ratio (RCR). State 4, the idle or resting state, results when coupled mitochondrial respire in a medium containing inorganic phosphate and a Kreb's cycle substrate in the absence of a phosphate acceptor such as adenosine diphosphate (ADP). In the presence of ADP the respiration rate increases to a maximum (state 3), accompanied by phosphorylation of ADP to adenosine triphosphate ...
1990-05-01
International Nuclear Information System (INIS)
Platelet deposition on bovine pericardial-tissue mitral-valve prostheses in 11 dogs was observed noninvasively by use of "1"1"1In-labeled platelets and quantified after sacrifice at one (n . 3), 14 (n . 3), and 30 (n . 5) days postimplantation (300-400 microCi of labeled platelets having been injected 24 hours previously). Thrombosis on the sewing ring and pericardial leaflets at one and 14 days and on the leaflets at 30 days was delineated in scintiphotos. In vitro quantification (% injected dose) indicated that the leaflets, sewing ring, and perivalvular tissue retained 0.904% of labeled platelets at one day postimplantation, 0.198% at 14 days, and 0.040% at 30 days. Platelet half-life was reduced to 38 hours at 21 days postimplantation but returned toward the normal (50 hours) with fibrous ingrowth in the sewing ring. Microembolism in lung and kidney, as measured by tissue/blood radioactivity ratio, also was decreased significantly at 30 days. "1"1"1In-labeled ...
International Nuclear Information System (INIS)
Synthesis of Eu-doped #beta#- and 15R-SiAlONs was studied by the ammonia nitridation of precursors derived from an #alpha#-Si_3N_4 fine powder dispersed in aluminum glycine gel with various Si/Al ratio and post-annealing in a nitrogen pressure furnace. The largest amount of #beta#-SiAlON was observed in the product at 1750 deg. C for Si/Al = 1/1 with small amounts of both #alpha#- and 15R-SiAlON impurities. The product showed two emissions at around 420 nm and 560 nm. The emission intensities decreased with increasing amount of #beta#-SiAlON. The former and latter emissions were assigned to Eu"2"+ in the 15R- and #alpha#-SiAlONs impurities. A mixture of Eu-doped 15R-SiAlON with #alpha#-Al_2O_3 impurity was obtained for Si/Al = 1/6, using AlN together with Al(NO_3)_3.9H_2O in a 2/1 atomic ratio as the aluminum source. It showed a bluish-white emission at 450 nm under 254 nm radiation.
2009-11-13
Energy Technology Data Exchange (ETDEWEB)
The suitability of the turbulent combustion flamelets model in order to predict the index of NO{sub x} production in turbulent flames of hydrogen diffusion is analyzed. In the flamelet approach, the turbulent flame is equivalent to a group of laminar flames submitted to a mechanical stretching which generates a chemical disequilibrium. This effect can be described by the stretching or by the scalar dissipation ratio. A numerical modeling is performed in order to evaluate the advantages of both approaches and to compare the behaviour of the NO{sub x} emission index with the experiments of Chen and Driscoll. This study shows that predictions of NO{sub x} emission indexes have a correct behaviour with respect to the Damkoehler number only when the scalar dissipation ratio is used as a parameter to describe the chemical state outside equilibrium. Predictions of the flamelet models are improving when the Damkoehler number ...
1996-12-31
Physico Mechanical Properties of Irradiated Waste Rubber Cement Mortar
International Nuclear Information System (INIS)
In the present study a partial replacement of aggregate with two different ratios of waste rubber (5%, 10%) with the addition of a constant ratio of rice husk ash (RHA), 5% was carried out. The hardened cement mortar used the optimum water of consistency. The specimens were molded into 1 inch cubic moulds .The specimens were first cured for 24 hours, at 100% relative humidity and then cured under tap water for 3, 7 and 28 days followed by irradiation at different doses of gamma irradiation namely 5 and 10 kGy. The physico-chemical and mechanical properties such as compressive strength, total porosity and bulk density were studied for the three types of specimens. The results showed that the values of the compressive strength, bulk density and chemically combined water of the blended cement mortar paste (OPC-RHA) increase ,while blended cement mortar paste with 5% RHA and 5, 10% waste rubber decrease. The results were ...
Energy Technology Data Exchange (ETDEWEB)
Qualitative and quantitative methods have been developed to relate phosphate/UO{sub 2} interactions and U dissolution, in vitro, in a medium containing 0 or 10 mM phosphate concentrations at pH 5. This was performed by Energy Dispersive X ray Spectrometry (EDS) at 200 kV on entire particles and by fluorimetric measurement. The U dissolution rate was larger in a medium without phosphate than in a medium containing 10 mM phosphate. During the first day, the initial U dissolution involved 80.55% and 91.13% of the powder in media with and without phosphate respectively. From 5 to 15 d after beginning the assay, the dissolution half-times were longer than 92 d and 22 d for media with and without phosphate. EDS analyses have shown a constant P/U X ray intensity ratio for reference U{sub 2}O(PO{sub 4}){sub 2} for the same range of particle diameter. A gradual increase of this ratio was measured for UO{sub 2} incubated in a 10 mM ...
1998-07-01
Energy Technology Data Exchange (ETDEWEB)
Two computational problems were worked on for this study. The first chapter examines the option of coal combustion using oxygen feed with carbon dioxide recycle to control the adiabatic flame temperature. Computer simulations using an existing state-of-the-art 3-dimensional computer code for turbulent reacting flows with reacting particles were employed to study the effects of increased carbon dioxide mole fraction on the char burnout, radiant heat transfer, metal partitioning, and NOx formation. The second chapter compares assumptions for the CO/CO{sub 2} ratio at the surface of mineral inclusions made in previous studies to predictions obtained from a pseudo-steady state kinetic model (SKIPPY) for a single porous particle. The detailed kinetic simulations from SKIPPY for varying particle sizes and bulk gas compositions were used to develop algebraic expressions for the CO/CO{sub 2} ratio that can be incorporated into ...
2002-02-28
We report a new measurement of the exclusive electroproduction reaction {gamma}*p{yields}{pi}{sup 0}p to explore the evolution from soft nonperturbative physics to hard processes via the Q{sup 2} dependence of the magnetic (M{sub 1+}), electric (E{sub 1+}), and scalar (S{sub 1+}) multipoles in the N{yields}{delta} transition. 9000 differential cross section data points cover W from threshold to 1.4 GeV/c{sup 2}, 4{pi} center-of-mass solid angle, and Q{sup 2} from 3 to 6 GeV{sup 2}/c{sup 2}, the highest yet achieved. It is found that the magnetic form factor G{sub M}* decreases with Q{sup 2} more steeply than the proton magnetic form factor, the ratio E{sub 1+}/M{sub 1+} is small and negative, indicating strong helicity nonconservation, and the ratio S{sub 1+}/M{sub 1+} is negative, while its magnitude increases with Q{sup 2}.
2006-09-15
The visible absorption spectra of 1,4-(dihydroxy)-9,10-anthraquinone and of Co(II), Ni(II), Cu(II) and Zn(II) chelates have been studied in different organic solvents. This system provides a model for the anthracycline antibiotics and their metal chelates. The band structure of the spectrum has been determined using the second and fourth derivatives of the spectrum. The visible absorption band of the parent molecule can be assigned to a single electronic state with a reduced dipole moment in the excited state; structure in this band is ascribed to two overlapping vibrational progressions. In contrast, the dianion (hydroxy protons removed) shows a single electronic state with an increased dipole moment in the excited state; structure in this band can be assigned to a single vibrational progression. All of the metal chelates show spectra which are similar in appearance to that of the dianion although the identity of the metal determines the bathochromic shift of the ...
1990-08-15
Fuel assembly and reactor core
International Nuclear Information System (INIS)
In a fuel assembly having moderator rods, an axial average value of a ratio between the total of the lateral cross sectional area of a portion to be filled with moderators and the total of the lateral cross sectional area of fuel pellets is determined as greater than 0.4, a lateral cross sectional area of a portion to be filled with moderators per one moderator rod is determined as from 14 to 50cm"2 and the ratio between the total of the lateral cross sectional area of moderators and a total of the lateral cross sectional area of fuel pellets in a horizontal cross section is determined as from 2.7 to 3.4. Since the axial average value for lateral cross sectional area of a portion to be filled with moderators/lateral cross sectional area of fuel pellets is determined as #>=# 0.4, the lateral cross sectional area of moderators of moderator rods is increased, the lateral cross sectional area of a gap water region is ...
1992-12-03
Fragment angular momenta in low and medium energy fission of /sup 242/Pu
Energy Technology Data Exchange (ETDEWEB)
Independent isomeric yield ratios of /sup 128/Sb were determined radiochemically in the thermal neutron induced fission of /sup 241/Pu and 34 MeV alpha particle induced fission of /sup 238/U, both involving the same compound nucleus (/sup 242/Pu). Fragment angular momenta estimated from the measured isomer ratios using the statistical model analysis showed significantly larger fragment angular momenta in the medium energy fissioning system compared to the low energy fissioning system. This has been attributed to the effect of higher excitation energy and angular momentum in the entrance channel leading to increased fragment temperature, moments of inertia and angular velocity. An attempt was made to calculate the fragment angular momentum in the medium energy fission using the Fermi gas model for the fissioning nucleus, taking into account the multichance fission, saddle shapes of the fissioning nuclei and the angular ...
1987-06-01
International Nuclear Information System (INIS)
The electron-beam qualities with and without free electron laser (FEL) oscillations were investigated in the compact storage ring NIJI-IV. The peak-electron density in a bunch was suppressed by beam instabilities, so that it was limited to about 1.0 x 10"1"7 m"-"3. The maximum FEL gain estimated for 215 and 300 nm using a well-known one-dimension theory was about 2.8% and 4.6%. The cavity loss at 300 nm was evaluated to be about 2% from the threshold beam current. The bunch length and energy spread with FEL oscillations increased by 1.3 times or more due to bunch heating. The ratio of the FEL gain to a cavity loss estimated from the beam qualities with and without FEL oscillations was almost in accord with the ratio evaluated directly with the measured data of the FEL gain and the cavity loss. (author)
2003-09-01
Cosmic evolution of the atomic and molecular gas content of galaxies
We study the evolution of the cold gas content of galaxies by splitting the interstellar medium into its atomic and molecular hydrogen components, using the galaxy formation model GALFORM in the LCDM framework. We calculate the molecular-to-atomic hydrogen mass ratio, H2/HI, in each galaxy using two different approaches; the pressure-based empirical relation of Blitz & Rosolowsky and the theoretical model of Krumholz, McKeee & Tumlinson, and apply them to consistently calculate the star formation rates of galaxies. We find that the model based on the Blitz & Rosolowsky law predicts an HI mass function, CO(1-0) luminosity function, correlations between the H2/HI ratio and stellar and cold gas mass, and infrared-CO luminosity relation in good agreement with local and high redshift observations. The HI mass function evolves weakly with redshift, with the number density of high mass galaxies decreasing with ...
2011-01-01
Correlations are studied between the power density of Alfv\\'en-cyclotron waves (having frequencies between 0.02 and 2 Hz) and the ratio of the perpendicular and parallel temperature of the protons. The wave power spectrum is evaluated from high-resolution 3D magnetic field vector components, and the ion temperatures are derived from the velocity distribution functions as measured in fast solar wind during the Helios-2 primary mission at radial distances from the Sun between 0.3 AU and 0.9 AU. From our statistical analysis, we obtain a striking correlation between the increases in the proton temperature ratio and enhancements in the wave power spectrum. Near the Sun the transverse part of the wave power is often found to be by more than an order of magnitude higher than its longitudinal counterpart. Also the measured ion temperature anisotropy appears to be limited by the theoretical threshold value for the ion-cyclotron ...
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
Using electromatic field theory, a new method is developed for calculating alternating current in power cables installed in pipes of carbon steel (magnetic pipes). The technique for evaluating these losses is based on the method of images which replaces complicated distribution of currents in the system with a sequence of thin conductors. The method not only gives a mathematical framework for the solution of alternating current losses, but it also gives the underlying physical picture of effects contributing to these losses. Skin effect, proximity effect and losses due to the pipe are calculated separately. For the first time, the increase of losses in the conductors, when the cables are placed in a magetic pipe, are analyzed mathematically. Good agreement is obtained between the result of calculations and the experimentally determined ac-dc resistance ratios for pipe-type cables with concentric stranded copper conductors and also for cables ...
1985-04-01
Augmentation of laminar flow and heat transfer in flat tubes by means of helical screw-tape inserts
Energy Technology Data Exchange (ETDEWEB)
The heat transfer a characteristics and friction factor in the horizontal double pipes of flat tubes with full length helical screw element of different twist ratio and helical screw inserts with different spacer length are investigated. Cold and hot water are used as working fluid in tube side and shell side respectively. The experiments covered a range of Reynolds numbers 5.7 x 10{sup 2} {<=} Re {<=} 1.31 x 10{sup 3}. The effect of spacer length on the heat transfer augmentation and friction factor and the effect of twist ratio on heat transfer augmentation and friction factor have been presented separately. The study shows that, the Nusslet number (Nu) and friction factor (f) decrease with the increase of S or Y for flat tube. The comparison between the data of present plain circular with that of previous plain circular tube showed a good agreement between them but the data of present plain flat tube showed ...
2011-01-15
Energy Technology Data Exchange (ETDEWEB)
With relation to the coals delivered as common samples in the coal fundamental technology development project, an experimental study was conducted on agglomeration characteristics and reaction characteristics in the fluidized-bed coal gasifier. For the experiment, used was a fluidized bed gasifier inserted with a cone-shape dispersion plate with a nozzle in the center. After raising the temperature of the gasifier up to 773K, gasification was conducted sending to the gasifier air from the nozzle and steam from the dispersion plate. The mean particle diameter and gas concentration of chars were measured till the temperature reaches 1373K. As a result of the experiment, it was confirmed that the carbon conversion ratio increases with a decrease in coalification degree of the coal. Moreover, influence of the coal kind was markedly observed at the grid zone of the lower part of the bed, and it was clarified that the lower carbon content ...
1996-10-28
We present new results from accurate and fully general-relativistic simulations of the coalescence of unmagnetized binary neutron stars with various mass ratios. The evolution of the stars is followed through the inspiral phase, the merger and prompt collapse to a black hole, up until the appearance of a thick accretion disk, which is studied as it enters and remains in a regime of quasi-steady accretion. Although a simple ideal-fluid equation of state with \\Gamma=2 is used, this work presents a systematic study within a fully general relativistic framework of the properties of the resulting black-hole--torus system produced by the merger of unequal-mass binaries. More specifically, we show that: (1) The mass of the torus increases considerably with the mass asymmetry and equal-mass binaries do not produce significant tori if they have a total baryonic mass M_tot >~ 3.7 M_sun; (2) Tori with masses M_tor ~ 0.2 M_sun are measured for binaries ...
2010-01-01
Sucrose phosphate synthase activity in rice grown at elevated CO sub 2 and temperature
Energy Technology Data Exchange (ETDEWEB)
Rice (Oryza sativa L.) was grown at 330 and 660 {mu}L CO{sub 2} L{sup {minus}1} and at 40/33/37, 34/27/31, and 28/21/25{degree}C day/night/paddy water temperatures respectively. Sucrose phosphate synthase (SPS) activity was measured at saturating substrate concentrations at 59 days after planting. SPS activity increased 2 and 3 fold with increasing CO{sub 2} at 28 and 34{degree}C air temperatures respectively. At 40{degree}C SPS activity decreased by 37% at elevated CO{sub 2} and most plants failed to reach maturity. Similar responses were found in leaf samples taken in the dark. These results indicate that SPS, an enzyme involved in the regulation of C partitioning in leaves, increases in activity at elevated CO{sub 2}. This is in contrast to previous results with soybean. The changes in SPS activity will also be discussed in relation to leaf starch/sucrose ratios.
1990-05-01
Joining of boron carbide using nickel interlayer
International Nuclear Information System (INIS)
Carbide ceramics such as boron carbide due to their unique properties such as low density, high refractoriness, and high strength to weight ratio have many applications in different industries. This study focuses on direct bonding of boron carbide for high temperature applications using nickel interlayer. The process variables such as bonding time, temperature, and pressure have been investigated. The microstructure of the joint area was studied using electron scanning microscope technique. At all the bonding temperatures ranging from 1150 to 1300degC a reaction layer formed across the ceramic/metal interface. The thickness of the reaction layer increased by increasing temperature. The strength of the bonded samples was measured using shear testing method. The highest strength value obtained was about 100 MPa and belonged to the samples bonded at 1250 for 75 min bonding time. The strength of the joints decreased by ...
Heat transfer augmentation in 3D internally finned and microfinned helical tube
Energy Technology Data Exchange (ETDEWEB)
Experiments are performed to investigate the single-phase flow and flow-boiling heat transfer augmentation in 3D internally finned and micro-finned helical tubes. The tests for single-phase flow heat transfer augmentation are carried out in helical tubes with a curvature of 0.0663 and a length of 1.15 m, and the examined range of the Reynolds number varies from 1000 to 8500. Within the applied range of Reynolds number, compared with the smooth helical tube, the average heat transfer augmentation ratio for the two finned tubes is 71% and 103%, but associated with a flow resistance increase of 90% and 140%, respectively. A higher fin height gives a higher heat transfer rate and a larger friction flow resistance. The tests for flow-boiling heat transfer are carried out in 3D internally micro-finned helical tube with a curvature of 0.0605 and a length of 0.668 m. Compared with that in the smooth helical tube, the boiling heat transfer coefficient ...
2005-05-01
Energy Technology Data Exchange (ETDEWEB)
Causes of variation of hydrocarbon (HC) concentration in cylinder to cylinder at idling condition in a direct injection diesel engine were studied. The ratio of l/d=6 gives larger HC variation in cylinder to cylinder than the l/d=2, where l means the nozzle hole length and d means the nozzle hole diameter. This is because the condition of l/d=6 can result in the large spray penetration and increase the fuel on the combustion chamber. The spray structure changes between nozzles and also changes between nozzle holes. This is not caused by the shape of nozzle hole but is affected by the pressure change near the inlet of nozzle hole when the needle valve is lifted. The change of spray structure can change the injection volume between nozzle holes. The injection volume is less for a nozzle hole where the curved angle becomes sharp to the nozzle central angle, and is more at the opposite side. When the injection volume of the nozzle hole near the ...
1992-07-01
Exhaust emissions from an indirect injection dual-fuel engine
Energy Technology Data Exchange (ETDEWEB)
Diesel engines operating on gaseous fuels are commonly known as dual-fuel engines. In the present work, a single-cylinder, compression ignition, indirect injection research (Ricardo E6) engine has been installed at United Arab Emirates University for investigation of the exhaust emissions when the engine is operating as a dual-fuel engine. The influence of changes in major operating and design parameters, such as the concentration of gaseous fuel in the cylinder charge, pilot fuel quantity, injection timing and intake temperature, on the production of exhaust emissions was investigated. Diesel fuel was used as the pilot fuel, while methane or propane was used as the main fuel which was inducted in the intake manifold and mixed with the intake air. The experimental investigations showed that the poor emissions at light loads can be improved significantly by increasing the concentration of gaseous fuel (total equivalence ratio), employing a large ...
2000-04-01
Energy Technology Data Exchange (ETDEWEB)
The fertilizer contribution to radio uptake by tomato plants was assessed. Tomato and soil samples from four different plantations were analyzed: two using organic fertilizer and two using phosphate fertilizer. The Ra concentrations in eight of the most used tomato fertilizers were determined. The concentration values ranged from 14 to 221 Bq/kg of Ra-226 and from 25 to 176 Bq/kg of Ra-228. Owing to the low Ra concentration and to the used fertilizer quantities, the fertilizers would not increase significantly the Ra soil concentration. However, the highest soil to plant concentration ratios were found in the plantations using phosphate fertilizers. This outcome pointed out the higher Ra availability in the phosphate fertilizer plantations than in the organic fertilizer plantations, showing a possible positive influence of phosphate fertilizers for the tomato Ra uptake. Due to the phosphate fertilizer used, the dose could ...
2001-07-01
Synthesis, crystal structure and photoluminescence of Eu-#alpha#-SiAlON
International Nuclear Information System (INIS)
Eu-#alpha#-SiAlON (Eu_m_/_2Si_1_2_-_m_-_nAl_m_+_nO_nN_1_6_-_n) was synthesized with nominal compositions having small m and n values, by firing the powder mixture of Eu_2Si_5N_8, #alpha#-Si_3N_4, AlN, and Al_2O_3 at 1900 "oC for 6 h under 1 MPa nitrogen atmosphere. The ratio of the oxidation state of Eu"2"+/Eu"3"+ was estimated from the X-ray absorption fine structure (XAFS) measurement. The observed X-ray absorption near edge spectrum (XANES) showed that the Eu ion in Eu-#alpha#-SiAlON was mainly in divalent state but also coexisted with a small amount of Eu in the trivalent state. The crystal structure of Eu-#alpha#-SiAlON was refined by the Rietveld analysis of the X-ray powder diffraction patterns. The lattice constants of the samples increased with increasing m and n values. The excitation band of Eu-#alpha#-SiAlON ranged from the ultraviolet to the visible light region and a broad emission band centered at about 590 ...
2010-08-20
Study on the distribution of P-32 in chicken
Energy Technology Data Exchange (ETDEWEB)
Radioactive phosphorus (P-32) was injected to the chicken in the purpose of determination of the uptake and distribution, as related to sex and hour differences of the various organs of the body. 2..mu..Ci of P-32 were injected to each chicken and the distribution of P-32 was observed at 1 hr, 6 hrs, 12 hrs, 24 hrs and 48 hrs after injection. In this experiment 34 heads of chicken were used (30 chicken for P-32, 4 chicken for control group) and the results obtained as follows: 1. The uptake of P-32 per gram of various organ in g. mm, femur (1 hr), liver, femur, tibia (24 hrs) and tibia (48 hrs) exhibited higher in the male than the female. 2. The uptake of P-32 per gram of various organ in heart, kidney, ovary (1 hr), kidney, brain (24 hrs) and kidney (48 hrs) exhibited higher in the female than the male. 3. The uptake ratio of brain, spleen, g. mm and tibia were increased gradually by the 12 hrs after injection of P-32, but decreased in liver, ...
1981-12-01
Increased Prevalence of Albuminuria in HIV-Infected Adults with Diabetes
ObjectiveHIV and type 2 diabetes are known risk factors for albuminuria, but no previous reports have characterized albuminuria in HIV-infected patients with diabetes.Research Design and MethodsWe performed a cross-sectional study including 73 HIV-infected adults with type 2 diabetes, 82 HIV-infected non-diabetics, and 61 diabetic control subjects without HIV. Serum creatinine >1.5 mg/dL was exclusionary. Albuminuria was defined as urinary albumin/creatinine ratio >30 mg/g.ResultsThe prevalence of albuminuria was significantly increased among HIV-infected diabetics (34% vs. 13% of HIV non-diabetic vs. 16% diabetic control, p?=?0.005). HIV status and diabetes remained significant predictors of albuminuria after adjusting for age, race, BMI, and blood pressure. Albumin/creatinine ratio correlated significantly with HIV viral load (r?=?0.28, p?=?0.0005) and HIV-infected subjects with albuminuria had significantly greater ...
2011-09-13
Correlation between electrochemical properties and corrosion resistance of zirconium alloys
International Nuclear Information System (INIS)
The electrochemical behavior of some zirconium alloys including Zry-2 with various #SIGMA#Ai from 2.5 x 10"-"2"0 to 1.2 x 10"-"1"7 (h), modified Zry-2 with iron contents of 0.15, 0.25, and 0.5%, and standard Zry-4 was studied by measuring anodic polarization curves in sulfuric acid solution. The results of these electrochemical tests were compared with those of steam autoclave tests. In Zry-2, the current peak was observed at 1250 mV (versus SCE) on the anodic polarization curve, and this peak area increased with #SIGMA#Ai and with the size of secondary precipitates. Also, this peak was closely correlated with nodular corrosion resistance as expected from the above results. As iron contents in modified Zry-2 increased, the current peak at 1,250 mV decreased and a new peak at 1,900 mV appeared. The former peak disappeared and the latter peak increased further at 0.5% iron. In Zry-4, the current peak was observed at 1,900 mV, ...
1995-09-11
Zeolite-supported catalysts. Report for August 1986-November 1987
Energy Technology Data Exchange (ETDEWEB)
The present paper is a comparative study of the cerium-containing nickel catalysts supported on x- and y-zeolites. In general, the addition of cerium ions caused an increase in the catalytic activity for CO hydrogenation and shifted the product selectivity to high molecular weight hydrocarbons. The degree of the effect of cerium additive depends on the ratio of cerium to nickel contents, the reduction temperature, and the nature of the supporting materials. Catalyst characterization, including volumetric hydrogen chemisorption, temperature programmed reduction/desorption, x-ray diffraction, surface area measurements, in-situ infrared spectroscopy and x-ray photoelectron spectroscopy, was performed in order to interpret the phenomena due to the effects of cerium additives and the support effect on Ni/zeolite catalysts.
1988-01-01
X-ray studies of solid n-H/sub 2/
Energy Technology Data Exchange (ETDEWEB)
Results of X-ray investigations of solid normal hydrogen are presented. Temperature dependences of the lattice parameteps, molar volumes, linear and volume expansion coefficients in the 2K-Tsub(melt) temperature range are obtaiped. An essential n-H/sub 2/ expansion anisotropy in the premelting temperature region is pointed out. It is shown that the hexagonal lattice parameter ratios over the whole investigated temperature range is considerably higher than for solid parahydrogen. A considerable difference in thermal expansion of normal hydrogen and parahydrogen in the low temperature region is revealed. It is caused by contribuation of a rotational subsystem, increasing with the temperature decrease to crystal expansion. A detailed analysis of solid n-H/sub 2/ thermodynamic properties is conducted. The data testifying to the presence of isomorphous phase transformation in the solid n-H/sub 2/ in the premelting temperature region are discussed.
1983-08-01
British Library Electronic Table of Contents (United Kingdom)
The treatment of peat with the solutions of phosphoric, citric, and oxalic acids in concentrations of 10???4 and 10???2 mol/l at solid phase to liquid ratios of 1: 2.5 and 1: 5 increased the absorption of ammonia by 6.4???39.7%. The absorption of ammonia was higher than the concentration of doping ion-exchange groups by a factor of 5???2000. With the use of EPR and IR spectroscopy, it was found that this phenomenon was caused by the transformation of polyconjugation systems as a result of the interaction of acids with the organic matrix of peat by a macrocoordination mechanism, which also improved the technological characteristics of the resulting sorbents. The absence of the destruction of organic matter with the use of low concentrations of weak acids makes it possible to use these sorbe...
2011-01-01
Toward unifying the description of meson and baryon properties
We present a Poincare covariant Faddeev equation, which enables the simultaneous prediction of meson and baryon observables using the leading order in a truncation of the Dyson-Schwinger equations that can systematically be improved. The solution describes a nucleon's dressed-quark core. The evolution of the nucleon mass with current-quark mass is discussed. A nucleon-photon current, which can produce nucleon form factors with realistic Q{sup 2} evolution, is described. Axial-vector diquark correlations lead to a neutron Dirac form factor that is negative, with r{sub 1}{sup nu}>r{sub 1}{sup nd}. The proton electric-magnetic form factor ratio falls with increasing Q{sup 2}.
2009-01-15
Thermal conductivity of sintered lithium orthosilicate compacts
British Library Electronic Table of Contents (United Kingdom)
The design of solid breeder blankets is strongly affected by the low values of thermal conductivity and density of ceramic breeder pebble beds. A significant rise of both quantities would enhance the thermal performance and lead to an increased tritium breeding ratio. In order to improve these quantities pretreated lithium orthosilicate pebble material was dry pressed and subsequently sintered. The thermal conductivity of cylindrical pellets was determined by the heat pulse method using a laser flash device. A pebble bed characteristic sample was also investigated in order to check the measurement accuracy in comparison with previous results. Furthermore, two samples of low density cellular ceramics were also prepared by infiltration of polymer foams with a ceramic slurry. The thermal cond...
2009-01-01
The temporal evolution of coronal loops observed by GOES-SXI
We study the temporal evolution of coronal loops using data from the Solar X-ray Imager (SXI) on board of GOES-12. This instrument allows us to follow in detail the full lifetime of coronal loops. The observed light curves suggest three somewhat distinct evolutionary phases: rise, main, and decay. The durations and characteristic timescales of these phases are much longer than a cooling time and indicate that the loop-averaged heating rate increases slowly, reaches a maintenance level, and then decreases slowly. This suggests that a single heating mechanism operates for the entire lifetime of the loop. For monolithic loops, the loop-averaged heating rate is the intrinsic energy release rate of the heating mechanism. For loops that are bundles of impulsively heated strands, it is an indication of the frequency of occurrence of individual heating events, or nanoflares. We show that the timescale of the loop-averaged heating rate is proportional to the timescale of ...
2006-01-01
The influence of bowl offset on air motion in a direct injection diesel engine
Energy Technology Data Exchange (ETDEWEB)
The influence of bowl offset on motored mean flow and turbulence in a direct injection diesel engine has been examined with the aid of a multi-dimensional flow code. Results are presented for three piston geometries. The bowl geometry of each piston was the same, while the offset between the bowl and the cylinder axis was varied from 0.0 to 9.6% of the bore. The swirl ratio at intake valve closing was also varied from 2.60 to 4.27. It was found that the angular momentum of the air at TDC was decreased by less than 8% when the bowl was offset. Nevertheless, the mean (squish and swirl) flows were strongly affected by the offset. In addition, the distribution of turbulent kinetic energy (predicted by the /delta/-e model) was modified. Moderate increases (10% or less) in mass averaged turbulence intensity at TDC with offset were observed.
1988-01-01
The Concentration-Density Relation of Galaxies in Las Campanas Redshift Survey
We report the results of the evaluation of the ``concentration-density'' relation of galaxies in the local universe, taking advantage of the very large and homogeneous data set available from the Las Campanas Redshift Survey (Shectman et al. 1996). This data set consists of galaxies inhabiting the entire range of galactic environments, from the sparsest field to the densest clusters, thus allowing us to study environmental variations without combining multiple data sets with inhomogeneous characteristics. Concentration is quantified by the automatically-measured concentration index $C$, which is a good measure of a galaxy's bulge-to-disk ratio. The environment of the sample galaxies is characterized both by the three-space local galaxy density and by membership in groups and clusters. We find that the distribution of C in galaxy populations varies both with local density and with cluster/group membership: the fraction of centrally-concentrated galaxies ...
1999-01-01
Temperature Dependent Constitutive Modeling for Magnesium Alloy Sheet
International Nuclear Information System (INIS)
Magnesium alloys have been increasingly used in automotive and electronic industries because of their excellent strength to weight ratio and EMI shielding properties. However, magnesium alloys have low formability at room temperature due to their unique mechanical behavior (twinning and untwining), prompting for forming at an elevated temperature. In this study, a temperature dependent constitutive model for magnesium alloy (AZ31B) sheet is developed. A hardening law based on non linear kinematic hardening model is used to consider Bauschinger effect properly. Material parameters are determined from a series of uni-axial cyclic experiments (T-C-T or C-T-C) with the temperature ranging 150-250 deg. C. The influence of temperature on the constitutive equation is introduced by the material parameters assumed to be functions of temperature. Fitting process of the assumed model to measured data is presented and the results are compared.
2010-06-15
Technology of GaAs metal-oxide-semiconductor solar cells
The growth of an oxide interfacial layer was recently found to increase the open-circuit voltage (OCV) and efficiency by up to 60 per cent in GaAs metal-semiconductor solar cells. Details of oxidation techniques to provide the necessary oxide thickness and chemical structure and using ozone, water-vapor-saturated oxygen, or oxygen gas discharges are described, as well as apparent crystallographic orientation effects. Preliminary results of the oxide chemistry obtained from X-ray, photoelectron spectroscopy are given. Ratios of arsenic oxide to gallium oxide of unity or less seem to be preferable. Samples with the highest OVC predominantly have As(+3) in the arsenic oxide rather than As(+5). A major difficulty at this time is a reduction in OCV by 100-200 mV when the antireflection coating is vacuum deposited.
1977-01-01
British Library Electronic Table of Contents (United Kingdom)
The dimercaptosuccinic acid metronidazole ester (DMSAMe) was synthesized and radiolabeled with 99mTc to form the 99mTc-DMSAMe complex in high yield. The radiochemical purity of the 99mTc-DMSAMe complex was over 90%, as measured by TLC and by HPLC, without any notable decomposition at room temperature over a period of 6?h. Its partition coefficient indicated that it was a lipophilic complex. The tumor cell experiment and the biodistribution in mice bearing S 180 tumor showed that the 99mTc-DMSAMe complex had a certain hypoxic selectivity and accumulated in the tumor with high uptake and good retention. The tumor/blood and tumor/muscle ratios increased with time, suggesting it would be a possible tumor hypoxia imaging agent.
2010-01-01
British Library Electronic Table of Contents (United Kingdom)
We investigated phase transition of ilmenite-type AgSbO3 to pyrochlore by post-heat treatment and the synergy effect of the mixed phases of AgSbO3 on the photocatalytic activities to enhance the activities. The AgSbO3 with an ilmenite structure was prepared by a cation-exchange method. Phase transition from the ilmenite to pyrochlore occurred by proper control of post-heat treatment. The sample that was obtained by post-heat treatment of ilmenite-type AgSbO3 at 660^oC for 3h consisted of both of the ilmenite and pyrochlore phases, and the sample at 685^oC for 4h mainly consisted of the pyrochlore phase. Together with an increase in the ratio of the pyrochlore phase, the optical absorption spectra blue-shifted. The band gaps of single phases of the ilmenite and the pyrochlore were 2.4 and 2...
2010-01-01
British Library Electronic Table of Contents (United Kingdom)
The physicochemical properties of binary lipid mixtures of diether C25,25 lipids and dipalmitoyl-L-a-phosphatidylcholine (DPPC) were studied using photon correlation, fluorescence and electron paramagnetic resonance spectroscopy, and transmission electron microscopy. These two types of lipids can be mixed at all molar ratios to form unilamellar and multilamellar liposomes. Fluorescence anisotropy of 1,6-diphenyl-1,3,5-hexatrien in mixed liposomes indicates that the abrupt changes in order parameter in the hydrophobic part of bilayer membranes made of DPPC lipids disappears with increasing mol%C25,25 lipids. Electron paramagnetic resonance spectroscopy shows that at temperatures below 50^oC, the interfacial regions of membrane bilayer of mixed liposomes is more fluid than for pure DPPC lipo...
2011-01-01
British Library Electronic Table of Contents (United Kingdom)
Abstract Entrapping inclusion complexes in liposomes has been proposed to increase the entrapment efficiency (EE) and stability of liposomes compared with conventional liposomes. In the present study, a stable honokiol-in-hydroxypropyl--cyclodextrin-in-liposome (honokiol-in-HP--CD-in-liposome) was developed as honokiol delivery system by a novel method. The final molar ratio of honokiol/HP--CD/lipid was selected as 1:2:2. The mean particle size was 123.5 nm, the zeta potential was -25.6 mV, and the EE was 91.09 2.76%. The release profile in vitro demonstrated that honokiol is released from honokiol-in-HP--CD-in-liposome with a sustained and slow speed. Crystallographic study indicated that honokiol was first bound within HP--CD and then the inclusion complex was encapsulated within liposom...
2011-01-01
Outcome for Gram-negative bacteraemia when following restrictive empirical antibiotic guidelines
British Library Electronic Table of Contents (United Kingdom)
Introduction: Restrictions in prescribing broad spectrum antimicrobials have been part of a strategy to reduce Clostridium difficile cases in the UK in recent years. However, there has been little work on assessing the safety of alternative antimicrobial agents. Methods: We performed an uncontrolled prospective observational survey over a 1-year period to determine the effectiveness and safety of a new antimicrobial stewardship programme in a district hospital in the UK. Results: In total, 227 Gram-negative bacteraemias (203 episodes) occurred in the study period. Guidelines were adequate in 194 of 203 (95%) episodes and 163 episodes (80.2%) received adequate therapy. Patients in the inadequate therapy group had >2-fold increased likelihood of death [odds ratio (OR) = 2.63, 95% confidence ...
2011-01-01
Optimized chatter resistance of viscoelastic turning bars
British Library Electronic Table of Contents (United Kingdom)
The regenerative-chatter resistance of a viscoelastic cantilever beam is analyzed and compared to the common dynamic vibration absorber (DVA) system. The beam represents a tool holder for turning operation in machining. The optimum structural parameters are found by maximizing the most negative real part of the frequency response function (FRF). The FRF is found analytically by using an appropriate Greens function. Keeping the cantilever static stiffness constant, further increase in the optimal resistance is achieved by changing the ratio between the two elastic moduli in the 3-parameter solid viscoelastic material model. Three additional chatter resistance indicators are also investigated: the most positive real part of the FRF, the magnitude of the FRF and the resonant frequency. It is ...
2009-01-01
Nonlinear response and stability of a spindle system supported by Ball bearings
Energy Technology Data Exchange (ETDEWEB)
In this effort, the nonlinear responses and stability of a spindle system supported by ball bearings are presented. The dynamics of this system is described by a set of second order differential equations with a nonlinear piecewise smooth force. The Floquet theory is applied to investigate the stability of the periodic solution. Due to the loss of contact between the raceways and balls in the ball bearing, the bending of the frequency response curves switch to the left at the weak resonance region, which is similar to the frequency response curves of a system with a soft spring. With the decrease of the bearing clearance, the bending of the frequency response curves switch to the right, which is similar to the frequency response curves of a system with a hard spring. Increase of the frequency ratio, the bending of frequency response curves transforms from left to right. The route to chaos through a period doubling process is also observed in ...
2010-09-15
Mixed-ligand complexes of scandium with 4-(2-pyridylazo)resorcinol and monocarboxylic acids
International Nuclear Information System (INIS)
Scandium reacts with 4-(2-pyridylazo)resorcinol in the presence of monocarboxylic acids (X) to form mixed-ligand complexes with a Sc:PAR:x ratio of 1:2:2. The chemical nature of this interaction has been established, and the extraction of these mixed-ligand complexes has also been investigated; stability constants and molar extinction coefficients have been calculated. The values of the latter decrease in the order CH_3COOH > CH_2ClCOOH > CCl_3COOH. The formation and extraction of mixed-ligand complexes in Sc-PAR-HX systems make it possible to increase the sensitivity and selectivity of scandium determination in comparison with the use of the Sc-PAR mono-ligand complex.
1987-09-01
Method of reducing volume of radioactive liquid waste
International Nuclear Information System (INIS)
Purpose: To enable the solidification of liquid waste containing radioactive substance in a free shape with large volume reduction ratio without a pulverizing step by producing solute in the liquid waste as a slurry in a predetermined organic solvent and forming it into a cake by mechanical exfoliation. Method: Liquid waste containing suitably concentrated radioactive substances is supplied to a centrifugal thin film evaporator together with an organic agent having a higher boiling point than water and a non aqueous solution to evaporate the water content, the solute in the waste is produced as a slurry in the organic solvent, and removed as cake-state solute slightly residued with the organic solvent by the mechanical exfoliation such as centrifugal exfoliation or settling exfoliation from the slurry-state liquid. Accordingly, it can be increased in size as compared with the powder reduced in volume of the radioactive liquid waste, and can be ...
1981-08-01
British Library Electronic Table of Contents (United Kingdom)
Spherical nano-sized YSZ (yttria stabilized ZrO2) powders were successfully synthesized via a reverse microemulsion system. The water droplets in the microemulsion system of yclohexane/water/span85/Triton X-100/hexyl alcohol can act as the nano-reactors which solubilize zirconium oxychloride and ammonia water separately. The minute original reactors are favor to the formation of nano-sized spherical YSZ powders and the dispersibility of the powders can be controlled effectually by adjusting the weight ratio of the LiNO3 molten salt to the precursor. The phase transformation from cubic to monoclinic starts at and 500??C and finally monoclinic and cubic phase with increased crytallinity coexist at 800??C. The effect of LiNO3 molten salt in the formation of YSZ powders was also discussed.
2008-01-01
British Library Electronic Table of Contents (United Kingdom)
Cellulose whiskers and microfibrillated cellulose (MFC) were extracted from the rachis of date palm tree and characterized. These cellulosic nanoparticles were used as reinforcing phase to prepare nanocomposite films using latex of natural rubber as matrix. These films were obtained by the casting/evaporation method. The properties of the ensuing nanocomposite films were investigated using differential scanning calorimetry, toluene and water uptake experiments, dynamic mechanical analysis and tensile tests. The stiffness of the natural rubber was significantly increased above its glass-rubber transition temperature upon nanoparticles addition. The reinforcing effect was shown to be higher for nanocomposites with MFC compared to whiskers. It was ascribed to the higher aspect ratio and possi...
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
The effect of varying pD(11-13,7) on the reaction of hydrogen with (Co/sup 11/(CN)/sub 5/)/sup 3/- in deuterium oxide has been studied by using infrared spectroscopy to determine the ratio of (Co/sup 111/(CN)/sub 5/X)/sup 3/- (X=H,D) in the solids precipitated from the steady state under hydrogen. The results show that the uptake of hydrogen does not liberate a free proton and that the rate of (Co/sup 111/(CN)/sub 5/H)/sup 3/- -D/sub 2/,0 exchange increases with pD but becomes pD independent at pD 7 greater than 13,5.
1982-01-01
Inflation and reheating in Bianchi type-IX cosmology
Energy Technology Data Exchange (ETDEWEB)
Within the framework of the Bianchi type-IX homogeneous space, we set up a system of coupled equations for the cosmic scale factors, scalar field, and radiative energy density. At the tree level, the equations are written in a self-consistent, Hartree-Fock form. For phi/sup 4/ theory, the system of nine first-order differential equations is solved numerically for a varying ratio of the energy of anisotropy to the vacuum energy. As the vacuum energy increases, there appears to be less reheating, since the energy of anisotropy is more efficiently converted into isotropic expansion. If the energy of anisotropy is large enough, the inflationary phase is prevented. In this case, a series of cosmological phase transitions will take place each time the square of the effective mass changes its sign.
1985-02-15
Inflation and reheating in Bianchi type-IX cosmology
International Nuclear Information System (INIS)
Within the framework of the Bianchi type-IX homogeneous space, we set up a system of coupled equations for the cosmic scale factors, scalar field, and radiative energy density. At the tree level, the equations are written in a self-consistent, Hartree-Fock form. For phi"4 theory, the system of nine first-order differential equations is solved numerically for a varying ratio of the energy of anisotropy to the vacuum energy. As the vacuum energy increases, there appears to be less reheating, since the energy of anisotropy is more efficiently converted into isotropic expansion. If the energy of anisotropy is large enough, the inflationary phase is prevented. In this case, a series of cosmological phase transitions will take place each time the square of the effective mass changes its sign.
British Library Electronic Table of Contents (United Kingdom)
Enterococci are mostly isolated from urinary tract infections (UTIs). Increasing antibiotic resistance affects the success rate in empirical treatment, thus makes antibiotic susceptibility tests important. The aim of this study was to determine the species distribution and resistance patterns of Enterococcus strains isolated from urine samples to antibacterial agents including fosfomycin in a teaching hospital, Istanbul. The identification of 100 Enterococcus strains were determined by using conventional methods and API 20 Strep (bioMerieux France). The susceptibility testing was performed by disk diffusion and Etest. The majority of isolates were E. faecalis (67%), followed by E. faecium (33%). The ratio of E. faecalis to E. faecium was 2.03/1. E. faecalis and E. faecium strains were resi...
2011-01-01
First ICRF heating experiment in the large helical device
Energy Technology Data Exchange (ETDEWEB)
Initial ICRF heating experiment in the LHD was carried out in 1998. One pair of the movable loop antennas was used and the coupling resistance was around one ohm for the low density ECH plasma. The loading characteristics were consistent with the fast wave excitation. By applying the ICRF heating of 300 kW to the ECH target plasma, the diamagnetic energy was increased from 13 kJ to 26 kJ. The heating performance was decided by hydrogen mixture rate on puffing gas. Efficient electron heating was observed at the higher hydrogen gas ratio. These results can be explained by the one dimensional wave analysis calculation on slab plasma model. (J.P.N.)
1999-07-01
Familiar and environmental factors influencing atopic dermatitis in the childhood
British Library Electronic Table of Contents (United Kingdom)
Abstract Background The increase in the incidence of atopic dermatitis (AD) in developed countries has been related to familiar and environmental factors. This survey was undertaken to investigate the family background, birthweight and the home environment of children suffering from AD in order to point out the possible factors that provoke the development of the disease. Methods The study uses data collected by means of self-administered questionnaires and discusses 461 cases of children (age 0-12) with active skin signs of AD. The control group comprised of 343 children (age 0-12) with no skin signs or positive lifetime history of AD. Associations between familiar and various home environmental factors and the risk of AD were calculated by means of odds ratios. Results There were statist...
2006-01-01
British Library Electronic Table of Contents (United Kingdom)
Fluorocarbon polymers are used to enhance thermal stability and electrostatic protection of composite propellant compositions. A precipitation technique has been developed to coat ammonium perchlorate (AP) using a copolymer of hexafluoropropylene and vinylidene fluoride (HFP-VF) with the help of solvent-counter solvent method. The coated AP has been used to prepare propellant compositions in different ratio based on hydroxyl terminated polybutadiene (HTPB), aluminium powder along with uncoated AP and studied for viscosity build-up and visco-elastic behaviour as well as mechanical, ballistic, thermal and sensitivity properties keeping 86% solid loading. The data on viscosity build-up indicate that as the percentage of viton coated AP increases end of mix viscosity and viscosity build-up inc...
2009-01-01
Dynamic response of a PEM fuel cell under reactant gas starvation
The fuel cell control problem was studied. Attempts were made to control the output current of the fuel cell by starving it of hydrogen and oxygen. The motivation of this work was to increase efficiency by minimizing waste of fuel. The following findings were obtained: H2 starvation works better than O2 starvation; An optimal H2 to O2 ratio exists for combined H2&O2 starvation; The control scheme for H2&O2 starvation works well for 3 different disturbance tests and at 25 degrees C, 60 degrees C, and 80 degrees C; Fuel cell under reactant starvation is stable for at least 72 hrs.
2005-08-05
Development of a small scintillation detector with an optical fiber for fast neutrons
International Nuclear Information System (INIS)
To investigate the characteristics of a reactor and a neutron generator, a small scintillation detector with an optical fiber with ThO_2 has been developed to measure fast neutrons. However, experimental facilities where "2"3"2Th can be used are limited by regulations, and S/N ratio is low because the background counts of this detector are increase by alpha decay of "2"3"2Th. The purpose of this study is to develop a new optical fiber detector for measuring fast neutrons that does not use nuclear material such as "2"3"2Th. From the measured and calculated results, the new optical fiber detector which uses ZnS(Ag) as a converter material together with a scintillator have the highest detection efficiency among several developed detectors. It is applied for the measurement of reaction rates generated from fast neutrons; furthermore, the absolute detection efficiency of this detector was obtained experimentally.
2011-02-01
British Library Electronic Table of Contents (United Kingdom)
Background Despite potentially relevant chemical differences between filtered and boiled coffee, this study is the first to investigate consumption in relation to the risk of incident cancer. Methods Subjects were from the V?sterbotten Intervention Project (64,603 participants, including 3,034 cases), with up to 15?years of follow-up. Hazard ratios (HR) were calculated by multivariate Cox regression. Results No associations were found for all cancer sites combined, or for prostate or colorectal cancer. For breast cancer, boiled coffee ?4 versus <1 occasions/day was associated with a reduced risk (HR?=?0.52, CI?=?0.30?0.88, p trend?=?0.247). An increased risk of premenopausal and a reduced risk of postmenopausal breast cancer were found for both total (HRpremenopausal?=?1.69, CI?=?0.96?2.98...
2010-01-01
Constraints on WIMP Dark Matter from the High Energy PAMELA $\\bar{p}/p$ data
A new calculation of the $\\bar{p}/p$ ratio in cosmic rays is compared to the recent PAMELA data. The good match up to 100 GeV allows to set constraints on exotic contributions from thermal WIMP dark matter candidates. We derive stringent limits on possible enhancements of the WIMP \\pbar flux: a $m_{\\rm WIMP}$=100 GeV (1 TeV) signal cannot be increased by more than a factor 6 (40) without overrunning PAMELA data. Annihilation through the $W^+W^-$ channel is also inspected and cross-checked with $e^+/(e^-+e^+)$ data. This scenario is strongly disfavored as it fails to simultaneously reproduce positron and antiproton measurements.
2008-01-01
Complexity Adjusted Soft-Output Sphere Decoding by Adaptive LLR Clipping
A-posteriori probability (APP) receivers operating over multiple-input, multiple-output channels provide enhanced performance at the cost of increased complexity. However, employing full APP processing over favorable transmission environments, where less efficient approaches may already provide the required performance at a reduced complexity, results in waste of resources (e.g, processing energy/power). Therefore, for slowly varying channel statistics, substantial complexity savings can be achieved by simple adaptive schemes which perform performance tracking and adjust the complexity of the soft output sphere decoder by adaptively setting the related log-likelihood ratio (LLR) clipping value.
2010-01-01
Bioconversion of chicken wastes to value-added products
Energy Technology Data Exchange (ETDEWEB)
Increasing quantities of chicken waste concerns the poultry industry because of escalating disposal costs and the potential for environmental pollution. Biological conversion of these wastes to valuable products such as methane and/or chemical feed-stocks appears to be feasible. Biomethanation of chicken waste by a sewage sludge microbial consortium produced as much as 69 mol% methane in the gas phase. Acetic and propionic acids were the major acids produced during the bioconversion. Addition of chelating agents and other micro-nutrients enhanced methane production and shifted the ratios of intermediates accumulated. Preliminary data indicate that more than 60% of the chicken waste carbon was converted and that the nitrogen-rich residue may have potential as a soil additive. (author).
1991-01-01
Application of alloy 800 in PWRs
International Nuclear Information System (INIS)
Alloy 800 has been used by Siemens since 1968 and is now used by KWU for U-tubed steam generators in PWR's. The particular grade of alloy 800 that is used is within the ASTM-Specification B 163, but there have been modifications in composition to improve the corrosion resistance. First the permitted upper limit of carbon was reduced to 0.04% and was then further reduced to 0.03% and a stabilisation ratio of Ti : C >= 12 and Ti : C + N >= 8 was specified. The minimum permitted chromium and nickel levels were increased to 20% and 32% respectively. The maximum permitted levels of other elements or impurities were reduced. At the final fabrication stage peening with glass beads on the outer surface was specified to introduce a compressive stress to depth greater than that allowed for production flaws. An account is given of the behaviour of the alloy in service in four power plants already in operation, and future developments are discussed. ...
International Nuclear Information System (INIS)
In this work, a water-soluble polymer, polyethylenimine (PEI) was used for the simultaneous separation and preconcentration of trace Cu and Mn prior to their determination by flame atomic absorption spectrometry. For this purpose, the sample and the PEI solution were mixed and the metal-bound polymer was precipitated by adding acetone. The precipitate was separated and dissolved in a minimum amounts of water and aspirated into a flame AAS. By increasing the ratio of the volumes of sample to water used in dissolving the precipitate, the analyte elements were concentrated as needed. The sorption is quantitative in the pH ?6. Detection limits were 5.2 ?g/L for Cu and 5.4 ?g/L for Mn. This method is simple, fast and precise.
2006-04-21
British Library Electronic Table of Contents (United Kingdom)
Abstract Acute lung injury (ALI) in sepsis is characterized by an increase in microvascular permeability, resulting in pulmonary edema. Several studies have suggested that angiopoietin-1 and -2 play a contributory role in the pathogenesis of ALI. Polymyxin B-immobilized fiber column hemoperfusion is effective for sepsis-induced ALI. We investigated the angiopoietin levels before and after direct hemoperfusion with polymyxin B-immobilized fiber column (PMX) therapy. Enzyme-linked immunoassay was used to measure the serum angiopoietin-1 and -2 levels in 25 patients with septic shock treated with PMX. Eleven of the 25 patients were diagnosed with ALI. There was a significant positive correlation between the angiopoietin-1 level and the PaO2/FiO2 ratio, but there was a significant inverse corr...
2011-01-01
"9"9"mTechnetium-heat damaged erythrocyte spleen scan
International Nuclear Information System (INIS)
"9"9"mTechnetium -heat damaged erythrocyte were used as spleen scanning agents in 12 patients from July, 1985 to April, 1986. We used this scan to evaluate situs inversus, asplenia, accessory spleen, hypersplenism, splenic infarction, tumor staging and evaluation of therapy, especially when the "9"9"mTc-tin colloid scans were not definite for diagnosis. The techniques applied to these scans were in vivo/in vitro-labeling method and heating-method to damage the erythrocytes. Liver-to-spleen uptake ratios were increased upto 100:1 and interference from the left lobe of the liver was eliminated. These scans were helpful to evaluate the spleen. (Author).
Energy Technology Data Exchange (ETDEWEB)
K{beta}-to-K{alpha} X-ray intensity ratios of Ti, Cr, Fe and Co in pure metals and in Cr{sub 0.26}Fe{sub 0.74}, Cr{sub 0.80}Co{sub 0.20} and Ti{sub 0.80}Cr{sub 0.20} alloys have been measured following excitation by 59.54 keV {gamma}-rays from a 7400 MBq (200 mCi) {sup 241}Am point-source. The valence electronic structure of Ti, Cr, Fe and Co in the samples have been evaluated by the comparison of the measured K{beta}-to-K{alpha} intensity ratios with the results of multiconfiguration Dirac-Fock calculations performed for various electronic configurations of these metals. The 3d-electron populations obtained for pure metallic Ti, Cr, Fe and Co agree well with the results of band structure calculations of Papaconstantopoulos (Handbook of band structure of elemental solids, Plenum Press, New York, 1986). Our analysis indicates significant increase of 3d-electron population of Ti, Cr and Fe in the alloys with respect to the ...
2002-10-01
International Nuclear Information System (INIS)
K#beta#-to-K#alpha# X-ray intensity ratios of Ti, Cr, Fe and Co in pure metals and in Cr_0_._2_6Fe_0_._7_4, Cr_0_._8_0Co_0_._2_0 and Ti_0_._8_0Cr_0_._2_0 alloys have been measured following excitation by 59.54 keV #gamma#-rays from a 7400 MBq (200 mCi) "2"4"1Am point-source. The valence electronic structure of Ti, Cr, Fe and Co in the samples have been evaluated by the comparison of the measured K#beta#-to-K#alpha# intensity ratios with the results of multiconfiguration Dirac-Fock calculations performed for various electronic configurations of these metals. The 3d-electron populations obtained for pure metallic Ti, Cr, Fe and Co agree well with the results of band structure calculations of Papaconstantopoulos (Handbook of band structure of elemental solids, Plenum Press, New York, 1986). Our analysis indicates significant increase of 3d-electron population of Ti, Cr and Fe in the alloys with respect to the pure metals, ...
2002-10-01
Energy Technology Data Exchange (ETDEWEB)
The present study deals with two subjects. The first one is to determine the thermal properties of lauric acid (LA)-stearic acid (SA), myristic acid (MA)-palmitic acid (PA) and palmitic acid (PA)-stearic acid (SA) eutectic mixtures as latent heat storage material. The properties were measured by the differential scanning calorimetry (DSC) analysis technique. The second one is to study the thermal reliability of these materials in view of the change in their melting temperatures and latent heats of fusion with respect to repeated thermal cycles. For this aim, the eutectic mixtures were subjected to 360 repeated melt/freeze cycles, and their thermal properties were measured after 0, 90,1 80 and 360 thermal cycles by the technique of DSC analysis. The DSC thermal analysis results show that the binary systems of LA-SA in the ratio of 75.5:24.5 wt.%, MA-PA in the ratio of 58:42 wt.% and PA-SA in the ratio of 64.2:35.8 wt.% form ...
2004-02-01
Induction and use of sex linked lethal mutations in the pink bollworm
International Nuclear Information System (INIS)
The sterile insect release technique can often be improved by removal of females before release. Rearing efficiencies can also be increased if removal of the females occurs at early developmental stages. In order to begin to develop genetic sexing strains for the pink bollworm, Pectinophora gossypiella (Saunders), it was necessary to determine the best dosage of radiation for induction of viable sex linked recessive lethal mutations and to see if stocks containing induced sex linked lethals could be maintained in culture. Sex linked recessive lethal mutations can be detected by distorted sex ratios in the progeny of treated adults. However, in the pink bollworm, highly distorted sex ratios are common even in the absence of induced mutations. Therefore, a visible sex linked trait, purple eye, was used as a marker for the untreated X-chromosomes in crosses. Thus, the presence of a recessive sex linked lethal mutation induced ...
1987-11-16
Efficient low-emission burners for natural gas domestic cooktops
Energy Technology Data Exchange (ETDEWEB)
Three new partially-aerated burners have been developed for Australian cooktops fired with natural gas, with maximum thermal inputs of 12, 7.5 and 5.5 MJ h{sup -1}. These novel burner designs minimise the NO{sub 2} emission per unit of useful energy, since NO{sub 2} is the more toxic nitrogen oxide of concern for indoor air pollution. They provide lower values of the ratio of NO{sub 2} emission to thermal efficiency than production burners, with respective reductions of 42, 13 and 23% compared with production burners of corresponding size. The traditional combustion diagrams of these prototype burners have been defined, on plots of primary aeration versus thermal input, to identify the regions of stable flame operation. However, the regions of satisfactory operation are further limited at low primary aeration by the Australian Gas Association requirement for CO/CO{sub 2} ratio <0.01 and at low thermal inputs by the requirement for ...
2000-03-01
International Nuclear Information System (INIS)
The distribution of carrier-free "2"0"3Pb-acetate, "2"0"3HgCl_2, "5"7Cocl_2, "1"3"7CsCl and "2"0"1TlCl was investigated in rats bearing thigh-implanted Morris 7777 hepatomas. Viable and nonviable tumor tissue was collected in order to determine the relative affinities of the radiopharmaceutical for these tissues. The animals were sacrificed at 4, 24, 48, 72 and 96 hrs following intravenous injection. Washout of the radioisotope from the viable tumor tissue was rapid, the maximum concentration being reached on or before 4 hrs following injection. In contrast, residual activity within the nonviable tumor tissue decreased much more slowly and in some cases even increased with time. Viable tumor-to-muscle and nonvialbe tumor-to-muscle ratios for "2"0"3Pb, "2"0"3Hg and "5"7Co were comparable to the analogous ratios reported for "6"7Ga. However, none of these isotopes approached "6"7Ga as a potential tumor imaging agent because ...
Combined release of radiation sterilized adults of spotted bollworm, Earias vittella (Fabricius)
International Nuclear Information System (INIS)
Feasibility of using combined release of sterile males and sterile females for population suppression of Earias vittella (Fabricius) was evaluated on okra in two ways. In one study, a combined release of sterile males and sterile females was evaluated under simulated conditions in laboratory, a 10: 10: 1: 1 (sterile male: sterile female: normal female: normal male) ratio effected > 99% sterility. In the second study, in a field cage experiment, a combined release of sterile males and sterile females was evaluated using normal males and tethered normal females. In this experiment, the release of sterile males and sterile females in 10: 10: 1: 1 ratio caused complete 'shut off' of mating of normal females for first 2 days and indicated>93% reduction in the larval progeny in the next generation. The tethered females were allowed to mate only once. E. vittella females mate multiply and so with overwhelming numbers of sterile males present, ...
2005-06-01
Chemical Makeup of Microdamaged Bone Differs from Undamaged Bone
International Nuclear Information System (INIS)
Microdamage naturally occurs in bone tissue as a result of cyclic loading placed on the body from normal daily activities. While it is usually repaired through the bone turnover process, accumulation of microdamage may result in reduced bone quality and increased fracture risk. It is unclear whether certain areas of bone are more susceptible to microdamage than others due to compositional differences. This study examines whether areas of microdamaged bone are chemically different than undamaged areas of bone. Bone samples (L3 vertebrae) were harvested from 15 dogs. Samples were stained with basic fuchsin, embedded in poly-methylmethacrylate, and cut into 5-(micro)m-thick sections. Fuchsin staining was used to identify regions of microdamage, and synchrotron infrared microspectroscopic imaging was used to determine the local bone composition. Results showed that microdamaged areas of bone were chemically different than the surrounding undamaged areas. Specifically, ...
2006-01-01
Analysis of impurities in beryllium, affecting evaluation of the tritium breeding ratio
International Nuclear Information System (INIS)
In most conceptual fusion power reactor designs, it is proposed to use beryllium as a neutron multiplier in the blanket. Detailed chemical composition of beryllium is necessary for evaluation of the tritium breeding ratio, and estimating the activation and transmutation of beryllium in the fusion reactor. In the present report, special attention was paid to a detailed analysis of impurities in beryllium, relevant to the tritium breeding ratio evaluation. Two different methods were used for the study of impurities: an analysis of the local sample by the ICP-MS method, and an integral analysis of the beryllium assembly, using the pulsed neutron method. The latter method was proposed as the most effective way of analyzing the integral effect to impurities in beryllium on production of the tritium on the lithium-6. The evaluation of the integral effect was based on time behaviour observations of the thermal neutron flux, following the injection of ...
Co-combustion of recycled waste materials with peat and coal in a 15 kw fluidized bed reactor
Energy Technology Data Exchange (ETDEWEB)
Co-combustion tests for recycled fuels and peat were made at a 15 kW fluidized bed reactor at VTT Energy in Jyvaeskylae. Peat was used as reference fuel. 25 tests in total were performed during 1994 - 1996. A part of the peat energy was substituted by coal in five tests, in order to change the sulphur/chlorine ratio of the fuel mixture. Fuel mixtures (25% recycled fuel and 75% peat, at energy ratio) were pelletized in order to get homogeneous fuel mixtures. The tests in the year 1994 were air staging experiments (with and without tertiary air). All test were performed with air staging in the years 1995 and 1996. The aim of the research was to determine whether the co-combustion of waste materials will cause additional emission problems, as compared to combustible emissions from conventional air-staged fluidized bed combustion. Further, the aim was to study which large-volume components can be burned safely. One aim was to study the influence of ...
1998-12-31
Determination of the Sr/Ca ratio in bones by XRFA
International Nuclear Information System (INIS)
Radionuclide X-ray fluorescence analysis was used for the determination of Sr/Ca ratio in bones to test the influence of a diet on this ratio. Significant differences were observed for Sr/Ca ratio in bones of various animals. Only small differences in the Ca/Sr ratio were observed for the samples of various prehistoric human bones. (author) 4 refs.; 4 tabs.
1989-11-01
Experimental and theoretical studies on humidification-dehumidification-desalination
Energy Technology Data Exchange (ETDEWEB)
The shortage of fresh water is increasing at alarming levels, even in temperate zones. Desalination of brackish and seawater is being considered as a solution to growing water demands. Seawater desalination can be accomplished through reverse osmosis, vapor compression, vapor absorption and thermally driven systems. The most suitable process for large-scale desalination plants is successive brine evaporation-condensation with intermediate heat recovery. However, higher process efficiency could be achieved. The use of low temperature heat sources in seawater desalination requires an efficient method of evaporation and condensation at relatively low vapor pressures. This could be achieved in a humidification-dehumidification process using circulated air to enhance evaporation of water. Simulation models, however, neglect either the heat of evaporation or the changes in air and water properties within humidification and condensation towers. Therefore, the purpose of ...
2006-07-01
Energy Technology Data Exchange (ETDEWEB)
With an objective to use reproducible vegetable oil as a substitute fuel, studies were performed to use emulsified rapeseed oil at an optimal mixing ratio with water in a direct injection diesel engine. The experiment used a water cooled, lateral installation, single-cylinder, direct injection, four-cycle diesel engine, and the tested fuel used an emulsified rapeseed oil fuel with rapeseed oil added with water at a rate of 20% by weight. As a result of the experiment using the emulsified rapeseed oil, it was found that reducing the injection opening diameter smaller than the standard opening diameter improves the engine performance and simultaneously reduces concentrations of HC, CO and exhaust smoke. The optimal opening diameter was about 0.22 mm. Increasing the valve opening pressure reduced the NOx concentration, but increased the HC concentration. Using the emulsified rapeseed oil fuel accumulated more carbon below the ...
1994-09-30
Thermodynamic modeling of integrated SOFC systems for power and hydrogen productions
International Nuclear Information System (INIS)
Electricity generation from natural gas in gas turbine units can be made substantially more efficient by preliminary methane conversion to a synthesis gas containing hydrogen and carbon monoxide and/or by the use of some of the synthesis gas produced in industry. An alternative improvement involves the introduction of solid oxide fuel cells (SOFCs) and the use of the synthesis gas in them. In this study, a modified scheme of gas turbine cycle that includes an SOFC, a membrane reactor (instead of a traditional combustion chamber), and a catalytic reactor to perform methane conversion to produce hydrogen (synthesis gas) is proposed. Variations of the energy and exergy efficiencies of the integrated system with operating conditions are provided, showing, for example, that SOFC efficiency is enhanced if the fuel cell active area is augmented. The SOFC stack efficiency can be maximized by reducing the steam generation while increasing the stack size, although such ...
Study of the thermodynamic properties of (U,Ce)O{sub 2}
Energy Technology Data Exchange (ETDEWEB)
The X-ray diffraction analysis of (U,Ce)O{sub 2} with the CeO{sub 2} contents ranging from 0 to 20 mol% CeO{sub 2} was performed at room temperature to obtain the variation in the lattice parameter with the CeO{sub 2} content. Ultrasonic pulse echo measurements were also carried out to estimate the change in the mechanical properties of (U,Ce)O{sub 2} with the CeO{sub 2} content. The lattice parameter of (U,Ce)O{sub 2} was found to decrease with increasing CeO{sub 2} content. The variation in the lattice parameter with the CeO{sub 2} content closely followed the Vegard law. The shear and longitudinal velocities in (U,Ce)O{sub 2} were found to decrease with increasing CeO{sub 2} content. The Young`s and shear moduli, and Poisson`s ratio estimated from the wave velocities decreased with the CeO{sub 2} content. No mechanical property showed anomaly in low CeO{sub 2} content region. (orig.).
1997-08-01
Structure and surface and catalytic properties of Mg-Al basic oxides
Mg-Al mixed oxides with Mg/Al molar ratios of 0.5--9.0 were obtained by thermal decomposition of precipitated hydrotalcite precursors. The effect of composition on structure and surface and catalytic properties was studied by combining several characterization methods with ethanol conversion reactions. The nature, density, and strength of surface basic sites depended on the Al content. The catalyst activity and selectivity of Mg-Al mixed oxides in ethanol conversion reactions depended on composition. The dehydrogenation of ethanol to acetaldehyde and the aldol condensation to n-butanol both involved the initial surface ethoxide formation on a Lewis acid-strong base pair. The dehydration of ethanol to ethylene, and the coupling and dehydration to diethyl ether increased with Al content, probably reflecting the density increase of both Al{sup 3+}-O{sup 2{minus}} pairs and low- and medium-strength basic sites. Pure Al{sub ...
1998-09-10
Energy Technology Data Exchange (ETDEWEB)
Strain-induced crystallization of crosslinked natural rubber (NR) and its synthetic analogue, cis-1,4-polyisoprene (IR), both mixed with various amounts of stearic acid (SA), were investigated by time-resolved X-ray diffraction using a powerful synchrotron radiation source and simultaneous mechanical (tensile) measurement. No acceleration or retardation was observed on NR in spite of the increase of SA amount. Even the SA-free IR crystallized upon stretching, and the overall crystallization behavior of IR shifted to the larger strain ratio with increasing SA content. No difference due to the SA was detected in the deformation of crystal lattice by stress for both NR and IR. These results suggested that the extended network chains are effective for the initiation of crystallization upon stretching, while the role of SA is trivial. These behaviors are much different from their crystallization at low temperature by standing, ...
2007-01-01
Energy Technology Data Exchange (ETDEWEB)
The purpose of this study is to acquire fundamental knowledge about the factors for production and the physical properties of boards when wood powder is used as the main material and powder adhesive is used as the binder in the formation of wood boards under heat and pressure. The effects of temperature for pressing, specific gravity of board, and the ratio of adhesive on bending strength, internal binding force, and size and stability against moisture are investigated. The temperature behavior at the central area of boards under heat and pressure shows similar tendency of stagnation near 140degC which increases thereafter irrespective of the temperature of the hot plate in this experiment. The bending property increases linearly when the resin content is low, and shows the tendency of leveling off gradually when the resin content is larger than 20%. Linear relation with specific gravity if obtained in the 0.6 to 1.0 ...
1998-04-15
Energy Technology Data Exchange (ETDEWEB)
In order to establish the optimum fueling in a natural gas fueled dual fuel engine, tests were made for some operational parameters and their combination on the engine performances and the exhaust emissions. The results show that the gas oil quantity should be increased and gas oil injection timing should be advanced to suppress unburned hydrocarbon emission at middle and low output range, while the quantity should be reduced and the timing should be retarded to avoid onset of knock at high loads. The unburned hydrocarbon emission and the thermal efficiency are improved at the same load avoiding too lean natural gas premixture by restriction of intake charge air. However the improvement is limited because the ignition and initial combustion of pilot diesel fuel is deteriorated when the cylinder pressure is excessively lowered by throttling. The increase in pilot gas oil amount is effective for low-load operation and the adequate combination of ...
2000-07-25
Energy Technology Data Exchange (ETDEWEB)
Silicon nitride based ceramics have attracted considerable attention as good candidates for structural applications due to their excellent mechanical properties including strength, hardness, fracture toughness, and high temperature strength. These properties are strongly influenced by grain size and morphology, and by the degree of crystallinity and chemistry of grain boundary phases. In this work, the microstructure of Si{sub 3}N{sub 4} densified with Nd{sub 2}O{sub 3}, Y{sub 2}O{sub 3} and Al{sub 2}O{sub 3} sintering additives was studied. Sintered samples were polished and plasma etched for microstructural analysis using scanning electron microscope. Quantitative evaluation of materials microstructure was accomplished using Quantikov software. Fracture toughness was measured by Vickers indentation method. The observed microstructure is typical of silicon nitride based materials and is characterized by high aspect ratio.-Si{sub 3}N{sub 4} grains embedded into a ...
2003-07-01
Increasing the pore size of electrospun scaffolds.
Electrospinning has gained much attention in the past decade as an effective means of generating nano- to micro-scale polymer fibers that resemble native extracellular matrix. High porosity, pore interconnectivity, and large surface area to volume ratio of electrospun scaffolds make them highly conducive to cellular adhesion and growth. However, inherently small pores of electrospun scaffolds do not promote adequate cellular infiltration and tissue ingrowth. Cellular infiltration into the scaffold is essential for a range of tissue engineering applications and is particularly important in skin and musculoskeletal engineering. Pore size, porosity, and pore interconnectivity dictate the extent of cellular infiltration and tissue ingrowth into the scaffold; influence a range of cellular processes; and are crucial for diffusion of nutrients, metabolites, and waste products. A number of electrospinning techniques and postelectrospinning modifications have, therefore, ...
2011-08-04
Energy Technology Data Exchange (ETDEWEB)
The experiment was carried out on a short rotation coppice culture of poplars (POP-EUROFACE, Central Italy), growing in a free air carbon dioxide enriched atmosphere (FACE). The specific objective of this work was to study whether elevated CO{sub 2} and fertilization (two CO{sub 2} treatments, elevated CO{sub 2} and control, two N fertilization treatments, fertilized and unfertilized), as well as the interaction between treatments caused an unbalanced nutritional status of leaves in three poplar species (P. x euramericana, P. nigra and P. alba). Finally, we discuss the ecological implications of a possible change in foliar nutrients concentration. CO{sub 2} enrichment reduced foliar nitrogen and increased the concentration of magnesium; whereas nitrogen fertilization had opposite effects on leaf nitrogen and magnesium concentrations. Moreover, the interaction between elevated CO{sub 2} and N fertilization amplified some element unbalances such as the ...
2007-06-15
Forced laminar convection in an array of stacked plates
Energy Technology Data Exchange (ETDEWEB)
A numerical study of laminar flow and heat transfer in an array of stacked rectangular plates is presented. The array is placed in a uniform stream, and the plates are subjected to a constant surface heat flux. This flow configuration is relevant to a number of practical heat transfer devices with finned surfaces. The computations were performed using a finite volume solution of the steady, two-dimensional Navier-Stokes equations and energy equation. A numerical scheme that reduces numerical diffusion is used to discretize the equations. The dominant feature of the flow is the separation, and subsequent reattachment of, the boundary layer, which takes place at Reynolds numbers greater than about 75. The separation first occurs downstream of the leading edge of the plate; then as Re increases, the separation point moves upstream and remains fixed at the leading edge, and the reattachment length increases linearly with Re. The appearance and ...
1994-04-01
Evaluation of ROP Margin Effectiveness by REFORM Region
Energy Technology Data Exchange (ETDEWEB)
In CANDU reactors, the Regional Overpower Protection Trip (ROPT) system protects the reactor against overpowers in the reactor fuel, whether due to localized peaking within the core or a general increase in core power levels. Due to Primary Heat-Transport System (PHTS) aging the ROP trip setpoint is decreasing over time. Reductions in ROP trip setpoints are required to maintain the required trip-probability and ROP trip effectiveness, and results in a decrease of the ROP margin-to-trip during normal operation. In addition, full power operation can be threatened. In this point, to recover ROPT margin, channel power needs to be redistributed. ROPT setpoint is very conservative in normal operation because distortion of regional overpower is over 1.2 times as nominal power in slow loss of regulation (SLOR). Channel power ratio (CPR) is enough low except the limiting channel of which worst case of design basis flux shape. If the outer channel power ...
2007-07-01
Effect of triple ion beams in ferritic/martensitic steel on swelling behavior
Energy Technology Data Exchange (ETDEWEB)
The synergistic effects of displacement damage and atomic hydrogen and helium on swelling of the ferritic/martensitic steel, F82H, has been investigated. The irradiation was performed at temperatures between 470 and 600 deg. C to 50 dpa (displacement per atoms) under conditions of simultaneous ion beams consisting of Fe{sup 3+}, He{sup +} and H{sup +} ions or Fe{sup 3+} and He{sup +} ions. The swelling of F82H steel under triple beams with 18 appm He/dpa and 70 appm H/dpa was larger than that under dual beams with 18 appm He/dpa. The swelling in F82H under triple beams increased with decreasing irradiation temperature from 0.1% to 3.2%, while swelling under dual beams was between 0.04% and 0.08%. On the other hand, in the case of triple beam irradiation with a high ratio of gas/dpa, the swelling tended to increase with irradiation temperature. The swelling in ferritic/martensitic steels is significantly enhanced by the ...
2002-12-01
Effect of triple ion beams in ferritic/martensitic steel on swelling behavior
International Nuclear Information System (INIS)
The synergistic effects of displacement damage and atomic hydrogen and helium on swelling of the ferritic/martensitic steel, F82H, has been investigated. The irradiation was performed at temperatures between 470 and 600 deg. C to 50 dpa (displacement per atoms) under conditions of simultaneous ion beams consisting of Fe"3"+, He"+ and H"+ ions or Fe"3"+ and He"+ ions. The swelling of F82H steel under triple beams with 18 appm He/dpa and 70 appm H/dpa was larger than that under dual beams with 18 appm He/dpa. The swelling in F82H under triple beams increased with decreasing irradiation temperature from 0.1% to 3.2%, while swelling under dual beams was between 0.04% and 0.08%. On the other hand, in the case of triple beam irradiation with a high ratio of gas/dpa, the swelling tended to increase with irradiation temperature. The swelling in ferritic/martensitic steels is significantly enhanced by the synergistic effect of ...
2002-12-01
Dynamic interpretation of organic-matter maturation and evolution of oil-generative window
Energy Technology Data Exchange (ETDEWEB)
Two phases are recognized in the maturation of organic matter and evolution of the oil-generative window (OGW): (a) a basinal subsidence phase during which potential source rocks undergo burial through a static initial OGW, and maturation is due essentially to increasing temperature with depth, and (b) a postsubsidence phase during which the OGW moves vertically upward through the static sedimentary fill, and maturation is due to time effects. Only the final shallow position of OGW can be defined by geochemical indices of maturity. The hydrocarbon generation sequence progresses from bottom to top, beginning with the lighter hydrocarbons (or even thermogenic gas) at the initial OGW at depth, followed by progressively heavier hydrocarbons as the OGW moves vertically upward. This dynamic model of hydrocarbon generation permits modeling of past positions of OGW relative to basin evolution through interpretation of oil-genesis nomographs. It also provides genetic ...
1984-08-01
International Nuclear Information System (INIS)
The paper reports on the results of hydrodynamical simulations of the late phase of the common envelope stage of a binary consisting of a 2-solar mass red giant and a 1-solar mass main-sequence companion. The numerical results demonstrate that sufficient energy is released from the orbit to eject the mass within the common envelope without requiring the main-sequence companion to spiral into the white dwarf core of the red giant star. At the end of the simulation the orbital decay time scale increases rapidly to more than 160 yr. The long decay time scale reflects the removal of mass from the common envelope and its subsequent spin-up to near corotation. The ratio of the orbital decay time scale to the mass-loss time scale from the common envelope increases to more than 700, and the mass contained within the common envelope decreases to about 0.01 solar mass or less. It is argued that further orbital decay will be small and ...
Energy Technology Data Exchange (ETDEWEB)
The aim of this research was to examine the energy equivalents of inputs and output in greenhouse vegetable production in the Antalya province of Turkey. For this purpose, the data for the production of four greenhouse crops (tomato, cucumber, eggplant and pepper) were collected in eighty-eight greenhouse farms by questionnaire. The results revealed that cucumber production was the most energy intensive of among the four crops investigated. Cucumber production consumed a total of 134.77 GJha{sup -1} followed by tomato with 127.32 GJha{sup -1}. The consumption of energy by eggplants and pepper were 98.68 and 80.25 GJha{sup -1}, respectively. The output-input energy ratio for greenhouse tomato, pepper, cucumber and eggplant were estimated to be 1.26, 0.99, 0.76 and 0.61, respectively. This indicated an intensive use of inputs in greenhouse vegetable production not accompanied by increase in the final product. This can lead to problems associated ...
2004-01-01
Energy Technology Data Exchange (ETDEWEB)
A sequential port injection, lean-burn, fully electronically-controlled compressed natural gas (CNG)/diesel dual-fuel engine has been developed based on a turbo-charged and inter-cooled direct injection (D.I.) diesel engine. During the optimisation of engine overall performance, the effects of pilot diesel and premixed CNG/air mixture equivalence ratio on emissions (CO, HC, NO{sub x}, soot), knocking, misfire and fuel economy are studied. The rich and lean boundaries of the premixed CNG/air mixture versus engine load are also provided, considering the acceptable values of NO{sub x} and THC emissions, respectively. It is interesting to find that there is a critical amount of pilot diesel for each load and speed point, which proved to be the optimum amount of pilot fuel. Any decrease in the amount of pilot diesel from this optimum amount results in an increase of NO{sub x} emissions, because the premixed CNG/air mixture must be made richer, ...
2003-07-01
A sensitivity study on neutronic properties of DUPIC fuel
Energy Technology Data Exchange (ETDEWEB)
A sensitivity study has been done to determine the composition of DUPIC fuel from the viewpoint of neutronics fuel design. The spent PWR fuel compositions were generated and fissile contents adjusted by blending fresh uranium after mixing two spent PWR fuel assemblies. The {sup 239}Pu and {sup 235}U enrichments of DUPIC fuel were adjusted by controlling the amount of fresh uranium feed and the ratio of slightly enriched and depleted uranium in the feed uranium. Based on the material balance calculation, it is recommended that DUPIC fuel composition be such that spent PWR fuel utilization is more than 90%. A sensitivity study on the temperature reactivity coefficient of DUPIC fuel and shown that it is desirable to increase the {sup 239}Pu and {sup 235}U contents to reduce both the fuel and coolant temperature coefficients. On the other hand, refueling simulations of the DUPIC core have shown that the channel power peaking factor, which is a ...
1998-12-31
Energy Technology Data Exchange (ETDEWEB)
Polychlorinated dibenzo-p-dioxins and dibenzo-furans form a family of more than 200 compounds which are relatively stable in the biosphere and tend to accumulate in the human body. The tetra- to hexa-chlorinated dioxins and furans are considered highly toxic. To facilitate the assessment of the total toxicity of dioxin and furan mixtures, the estimated toxic effects of the individual compounds relative to the 2,3,7,8-tetrachloro-dibenzo-p-dioxin (TCDD) were introduced as Toxic Equivalent Factors which yield, when multiplied with the respective concentrations, the Toxic Equivalent (TE) of the mixture. Toxic dioxins and furans are unintentionally formed in a number of industrial combustion processes such as waste incineration and iron ore sintering, in the chemical industry and in household heating. To keep the emissions as low as possible, off-gas clearing systems for the collection of dioxins and furans are increasingly prescribed by the authorities. In addition, ...
1997-12-31
In 1996, a field-scale phytoremediation demonstration project was initiated and managed by the U.S. Air Force at a site in western Fort Worth, Texas, using a plantation of 1-year-old stems harvested from branches of eastern cottonwoods during the dormant season (whips) and a plantation of 1-year-old eastern cottonwood seedlings (calipers). The primary objective of the demonstration project was to determine the effectiveness of eastern cottonwoods at reducing the mass of dissolved trichloroethene transported within an alluvial aquifer. The U.S. Geological Survey conducted a study, in cooperation with the U.S. Air Force, to determine water-level variations and their effects on tree growth and mortality and on the biogeochemical system at the phytoremediation site. As part of the study, water-level and water-quality data were collected throughout the duration of the project. This report presents water-level variations at periodic sampling events; data from August 1996 to January 2003 ...
2004-01-01
Energy Technology Data Exchange (ETDEWEB)
Magnetite nanoparticles with high self-heating capacity and low toxicity characteristics are a promising candidate for cancer hyperthermia treatment. In order to achieve minimum dosage to a patient, magnetic nanoparticles with high heating capacity are needed. In addition, the influence of physiological factors on the heat capacity of a material should be investigated in order to determine the feasibility. In this study, magnetite nanoparticles coated with lauric acid were prepared by co-precipitation of Fe{sup 3+}:Fe{sup 2+} in a ratio of 2:1, 5:3, 3:2, and 4:3, and the pH was controlled using NaOH. Structural and magnetization characterization by means of X-ray diffractometry (XRD) and a superconducting quantum interference device (SQUID) revealed that the main species was Fe{sub 3}O{sub 4} and further showed that most of the nanoparticles exhibited superparamagnetic properties. All of the magnetic nanoparticles showed a specific absorption rate (SAR) ...
2010-01-15
Interaction of antimicrobial peptides with lipid membranes
International Nuclear Information System (INIS)
This study aims to investigate the difference in the interaction of antimicrobial peptides with two classes of zwitterionic peptides, phosphatidylethanolamines (PE) and phosphatidylcholines (PC). Further experiments were performed on model membranes prepared from specific bacterial lipids, lipopolysaccharides (LPS) isolated from Salmonella minnesota. The structure of the lipid-peptide aqueous dispersions was studied by small-and wide-angle X-ray diffraction during heating and cooling from 5 to 85 C. The lipids and peptides were mixed at lipid-to-peptide ratios 10-10000 (POPE and POPC) or 2-50 (LPS). All experiments were performed at synchrotron soft condensed matter beamline A2 in Hasylab at Desy in Hamburg, Germany. The phases were identified and the lattice parameters were calculated. Alamethicin and melittin interact in similar ways with the lipids. Pure POPC forms only lamellar phases. POPE forms lamellar phases at low temperatures that upon heating transform ...
The compressive strength of cement blocks permeated with an organic phase change material
Energy Technology Data Exchange (ETDEWEB)
The authors investigate the feasibility of constructing walls and partitions with enhanced heat storage capability from cement blocks permeated with an organic phase change material (pressed stearic acid). The blocks are lightweight, easy to produce and are cured in the same way as cement or concrete. The ratio of components (cement, stearic acid (SA) and water) was optimized with respect to compressive strength. With normal portland cement, the best compressive strength 2.2 MPa was obtained with a ratio C:SA:W of 1:0.8:0.65 (i.e. 32% stearic acid) after 28 days of curing. This was increased to 4.4 MPa when high early strength cement was used, about as strong as Sipporex, lightweight concrete or lightweight clay bricks. As expected, the compressive strength decreased linearly with temperature between 25/sup 0/C and 100/sup 0/C, at a rate of 15 kPa//sup 0/C. The drying shrinkage of the modules was found to be 50% greater ...
1984-01-01
In our previous paper (Lanzafame et al. 2000, PASJ 52, 515) we showed, through 2D SPH simulations, that the stellar mass ratio, M 2 / M 1, of a close binary system (that determines the position and then the initial specific angular momentum at L 1) plays a fundamental role in the formation and development of spiral structures and shock fronts in the radial flow of accretion discs. In that work only a quasi-sonic value of the injection velocity at L 1 was considered. In the present work we also carried out 2D SPH simulations with the aim to investigate the development of such structures, while keeping constant the mass of the compact primary (M 1 = 1 M odot) and the separation between the two components, and assuming as an initial condition of two different supersonic injection velocities at L 1, characterizing two sets of simulations. For each set we considered four values of the secondary to primary mass ratio, M 2 / M 1. We worked out 2D ...
2001-02-01
Energy Technology Data Exchange (ETDEWEB)
A scaled physical model was operated to simulate steam drive operations in five-spot patterns with reservoir and operational parameters similar to those encountered in California reservoirs. The goal of this study was to elucidate the role of two important controllable parameters, viz., steam injection rate and steam quality and to explore the role of two important factors, oil viscosity and reservoir permeability on the performance of the steam drive. In addition, the influence of bottom water and a basal permeable layer were investigated. The experiments demonstrated that there is an optimum injection rate; that in the vicinity of this optimum an increased quantity results in improved oil steam ratios; that the viscosity of the oil at steam temperature, raised to a fractional power, 0.5, appears to correlate with oil production; that permeabilities in the darcy range have little effect on performance, but an increasing ...
1981-02-01
Real-time neutron radiography; Radiografia com neutrons em tempo-real
Energy Technology Data Exchange (ETDEWEB)
The main objective of the present thesis was develop and get operational a real-time neutron radiography system, at the IPEN-CNEN/SP. This system is installed inside the shielding of an old facility, designed in 1988, for film radiography, which is installed at the beam-hole 08 of the 5 MW, IEA-R1 Nuclear Research Reactor. The most important modifications at the such facility were the increase of the {gamma}-radiation filter thickness, increase of the inner area of the shielding, design of a neutron collimator and a light tight box. The main characteristics of the neutron beam at the irradiation position are: flux: 1 x 10{sup 6}n/cm{sup 2}s, collimation ratio 70, effective energy 7 meV, diameter 20 cm, neutron/{gamma} ratio {approx} 10{sup 6}n/cm{sup 2}mrem. The real-time images have been obtained by means of an imaging system that consists of a screen scintillator, a light intensifier, a video camera, ...
2000-07-01
International Nuclear Information System (INIS)
The main objective of the present thesis was develop and get operational a real-time neutron radiography system, at the IPEN-CNEN/SP. This system is installed inside the shielding of an old facility, designed in 1988, for film radiography, which is installed at the beam-hole 08 of the 5 MW, IEA-R1 Nuclear Research Reactor. The most important modifications at the such facility were the increase of the #gamma#-radiation filter thickness, increase of the inner area of the shielding, design of a neutron collimator and a light tight box. The main characteristics of the neutron beam at the irradiation position are: flux: 1 x 10"6n/cm"2s, collimation ratio 70, effective energy 7 meV, diameter 20 cm, neutron/#gamma# ratio #approx# 10"6n/cm"2mrem. The real-time images have been obtained by means of an imaging system that consists of a screen scintillator, a light intensifier, a video camera, a digitizing frame ...
2000-01-01
Kinetics and FTIR studies of hydrocarbon synthesis on Pd/ZSM5 catalysts. Final report
Energy Technology Data Exchange (ETDEWEB)
Hydrocarbon synthesis during CO hydrogenation over Pd/M-ZSM5 (M=H,Na,La) and Pd/SiO/sub 2/ has been investigated. Overall activity depended on the cation-exchanged form of the support and decreased in the order Pd/La-ZSM5 = Pd/Na-ZSM5 > Pd/H-ZSM5 > Pd/SiO/sub 2/. The zeolite-supported catalysts showed high selectivity towards saturated C/sub 2/-C/sub 6/ hydrocarbons, whereas Pd/SiO/sub 2/ favored methanol production. Increasing temperature and H/sub 2//CO feed ratio led to higher reaction rates, lower yields of C/sub 2/-C/sub 6/ products, and increased lighter hydrocarbons. A mechanical mixture of Pd/SiO/sub 2/ and Na-ZSM5 showed similar product distribution as Pd/Na-ZSM5. Infrared spectra of the catalysts under reaction conditions indicate the presence of adsorbed oxygenates on the zeolite. Changes in the IR bands during the initial stages of the reaction suggest that surface species on the zeolite are not methanol ...
1986-10-15
Experimental investigation of the KLL Auger spectrum of "8"8Sr from the EC-decay of "8"8Y
International Nuclear Information System (INIS)
According to the calculations, intensity of the KL_1L_2("3P_0) Auger transition should drastically increase with increasing atomic number Z due to the relativistic effects. However, this behavior was experimentally proved only for very few elements. A lack of enough precise experimental data in the atomic number region Z<45 does not enable one to distinguish between relativistic and non-relativistic approaches in this region. Thus for Z=38 the KL_1L_2("3P_0/"1P_1) intensity ratio was determined with relative uncertainty of 63 % in the only measurement with external excitation. Here we present results of our investigation of the KLL Auger electron spectrum of "8"8Sr generated in the EC decay of "8"8Y (T_1_/_2= 106.6 d). Electron spectra were measured with the 11 eV instrumental resolution using a combined electrostatic spectrometer. The present value of the KL_2L_3("1D_2) absolute transition energy in Sr is higher by 7.4 ...
2007-06-04
Evaluation of femoral neck fracture healing in man by serial sup(99m)Tc-diphosphonate scintimetry
Energy Technology Data Exchange (ETDEWEB)
In this study the distribution of sup(99m)Tc-diphosphonate and tetracycline and histological examination were also investigated in femoral heads obtained during replacement surgery. One hundred patients received scintigraphic examinations immediately after the occurrence of injury and every month thereafter. Ten mCi of sup(99m)Tc-diphosphonate was injected intravenously. Three hours later, detailed scintigrams of the bilateral hip areas were made with a scintillation camera connected to a computer. The uptake of sup(99m)Tc-diphosphonate in the fracture was expressed as a ratio of the counts recorded in one area to those recorded in the other area. A peak value in count ratio was recorded in all patients 4 to 6 weeks after fractures. One hundred patients were classified into a normal healing group and a delayed or non-union group. Namely, sup(99m)Tc-diphosphonate uptake was significantly higher in the delayed or non-union group than in the ...
1981-02-01
Evaluation of femoral neck fracture healing in man by serial sup(99m)Tc-diphosphonate scintimetry
International Nuclear Information System (INIS)
In this study the distribution of sup(99m)Tc-diphosphonate and tetracycline and histological examination were also investigated in femoral heads obtained during replacement surgery. One hundred patients received scintigraphic examinations immediately after the occurrence of injury and every month thereafter. Ten mCi of sup(99m)Tc-diphosphonate was injected intravenously. Three hours later, detailed scintigrams of the bilateral hips areas were made with a scintillation camera connected to a computer. The uptake of sup(99m)Tc-diphosphonate in the fracture was expressed as a ratio of the counts recorded in one area to those recorded in the other area. A peak value in count ratio was recorded in all patients 4 to 6 weeks after fractures. One hundred patients were classified into a normal healing group and a delayed or non-union group. Namely, sup(99m)Tc-diphosphonate uptake was significantly higher in the delayed or non-union group than in the ...
Criticality safety analysis for mockup facility
Energy Technology Data Exchange (ETDEWEB)
Benchmark calculations for SCALE4.4 CSAS6 module have been performed for 31 UO{sub 2} fuel, 15MOX fuel and 10 metal material criticality experiments and then calculation biases of the SCALE 4.4 CSAS6 module have been revealed to be 0.00982, 0.00579 and 0.02347, respectively. When CSAS6 is applied to the criticality safety analysis for the mockup facility in which several kinds of nuclear material components are included, the calculation bias of CSAS6 is conservatively taken to be 0.02347. With the aid of this benchmarked code system, criticality safety analyses for the mockup facility at normal and hypothetical accidental conditions have been carried out. It appears that the maximum K{sub eff} is 0.28356 well below than the critical limit, K{sub eff}=0.95 at normal condition. In a hypothetical accidental condition, the maximum K{sub eff} is found to be 0.73527 much lower than the subcritical limit. For another hypothetical accidental condition the nuclear material leaks out of ...
2000-03-01
Energy Technology Data Exchange (ETDEWEB)
Progress reports are presented for the following two areas: catalytic cracking studies with water-wet silica-alumina catalysts; and Fischer-Tropsch reactor studies where similarities and differences between fixed bed and slurry type reactors are investigated and further experiments conducted to measure mass transfer coefficients and reaction kinetics which are to be used in a model slurry reactor. The following are some of the conclusions. (1) The premise that the presence of liquid water might increase catalytic cracking activity was found to be invalid. It was demonstrated that cracking can occur at previously unobserved low temperatures (though at low conversions) and that an anomaly exists in that one of the catalysts tested shows an entirely different cracking behavior and probably follows a different cracking mechanism. (2) the diameter of a fixed-bed Fischer-Tropsch reactor critically affected the resistance of the reactor to plugging caused by the build up ...
1981-09-01
Chemical effects on K x-ray intensity ratios in chromium compounds
International Nuclear Information System (INIS)
K_#beta#/ K_#alpha# x-ray intensity ratio of chromium were measured in different chromium compounds. The results show the variation of the intensity ratio as a function of the chemical environment around the metal ion. (author)
2003-02-10
DUCTILITY RATIO OF AGED BETA TITANIUM ALLOY
... Title : DUCTILITY RATIO OF AGED BETA TITANIUM ALLOY. Corporate Author : NEW YORK UNIV NY SCHOOL OF ENGINEERING AND SCIENCE. ...
1962-01-02
Transmit-receive eddy current probes
International Nuclear Information System (INIS)
In the last two decades, due to increased inspection demands, eddy current instrumentation has advanced from single-frequency, single-output instruments to multifrequency, computer-aided systems. This has significantly increased the scope of eddy current testing, but, unfortunately, it has also increased the cost and complexity of inspections. In addition, this approach has not always improved defect detectability or signal-to-noise. Most eddy current testing applications are still performed with impedance probes, which have well known limitations. However, recent research at AECL has led to improved eddy current inspections through the design and development of transmit-receive (T/R) probes. T/R eddy current probes, with laterally displaced transmit and receive coils, present a number of advantages over impedance probes. They have improved signal-to-noise ratio in the presence of variable lift-off ...
1997-10-27
Energy Technology Data Exchange (ETDEWEB)
Glasses in the system (95-x) [0.25 Na{sub 2}O-0.75 B{sub 2}O{sub 3}]-x P{sub 2}O{sub 5}-5 Fe{sub 2}O{sub 3} (0<=x<=15 mol%), have been prepared by the melt quenching technique. Elastic properties and FT-IR spectroscopic studies have been employed to study the role of P{sub 2}O{sub 5} on the structure of the glass system. Elastic properties Poisson's ratio, micro-hardness and Debye temperature have been investigated using sound wave velocity measurements at 4 MHz (both longitudinal and shear) at room temperature. The results showed that the density and the molar volume increase as both sound velocities and the determined glass transition temperatures decrease with increasing the contents of P{sub 2}O{sub 5}. Infrared spectra of the glasses reveal that the borate network consists of diborate units and is affected by the increase in the concentration of P{sub 2}O{sub 5} content as a ...
2009-06-01
Raman spectroscopic studies of carbon in extra-terrestrial materials
International Nuclear Information System (INIS)
The measurements obtained here indicate ways in which micro-Raman spectroscopy can be used to elucidate structural characteristics and distribution of carbon in meteorites and interplanetary dust particles (IDPs). Existing information about structurally significant aspects of Raman measurements of graphite is combined with structurally relevant findings from the present micro-Raman studies of carbons prepared by carbonization of polyvinylidine chloride (PVDC) at various temperatures and natural material, as well as several acid residues from the Allende and Murchison meteorites in order to establish new spectra-structure relationships. Structural features of many of the materials in this study have been measured by x ray analysis and electron microscopy: thus, their structural differences can be directly correlated with differences in the Raman spectra. The spectral parameters consequently affirmed as indicators of structure are used as a measure of structure in materials that have ...
1990-04-01
NO{sub x} emissions of a jet diffusion flame which is surrounded by a shroud of combustion air
Energy Technology Data Exchange (ETDEWEB)
The present work reports an experimental study on the behavior of a jet flame surrounded by a shroud of combustion air. Measurements focussed on the flame length and the emissions of NO{sub x}, total unburned hydrocarbons, CO{sub 2}, and O{sub 2}. Four different fuel flow rates (40.0, 78.33, 138.33, and 166.6 cm/s), air flow rates up to 2500 cm{sup 3}/s and four different air injector diameters (0.079 cm, 0. 158 cm, 0.237 cm, and 0.316 cm) were used. The shroud of combustion air causes the flame length to decrease by a factor proportional to 1/[p{sub a}/p{sub f} + C{sub 2}({mu}{sub a}Re,a/{mu}{sub f}Re,f){sup 2}]{sup {1/2}}. A substantial shortening of the flame length occurred by increasing the air injection velocity keeping fuel rate fixed or conversely by lowering the fuel flow rate keeping air flow rate constant. NO{sub x} emissions ranging from 5 ppm to 64 ppm were observed and the emission of NO{sub x} decreased strongly with the ...
1996-08-01
DEFF Research Database (Denmark)
The coupling between cerebral metabolic rate of oxygen (CMRO2) and blood flow (CBF) in response to visual stimulation was evaluated by means of a model of oxygen delivery. The model predicted a nonlinear relationship between stimulus-evoked changes of oxygen consumption and blood flow. The magnitude of the CMRO2/CBF ratio index (IO2) was used to indicate the degree of flow-metabolism coupling prevailing in specific areas of the brain during physiological stimulation. Therefore, the index provided a measure of the blood oxygenation level dependent (BOLD) magnetic resonance contrast. To evaluate the changes of IO2 in response to visual stimulation, the model was applied to the effect of a changing flicker rate of a visual stimulus on the magnitudes of CBF, CMRO2, and oxygen diffusion capacity, in the human brain. Positron emission tomography (PET) was used to measure the CBF and the CMRO2 in 12 healthy volunteers who viewed a cross-hair (baseline) or a yellow-blue ...
2000-01-01
Energy Technology Data Exchange (ETDEWEB)
Dissolved humic substances (humic and fulvic acids) occur in surface waters and groundwaters in concentrations ranging from less than 1 mg(C)/L to more than 100 mg(C)/L. Humic substances are strong complexing agents for many trace metals in the environment and are also capable of forming stable soluble complexes or chelates with radionuclides. Concentrations of humic materials as low as 1 mg(C)/L can produce a detectable increase in the mobility of some actinide elements by forming soluble complexes that inhibit sorption of the radionuclides onto rock materials. The stability of trace metal- or radionuclide-organic complexes is commonly measured by an empirically determined conditional stability constant (K'), which is based on the ratio of complexed metal (radionuclide) in solution to the product concentration of uncomplexed metal and humic complexant. Larger values of stability constants indicate greater complex stability. The ...
1985-07-01
Elemental transfer from Chinese soil via the diet to the whole human body
International Nuclear Information System (INIS)
Based on results from recent studies of elemental dietary intake and organ or tissue content for adult Chinese men, quoted nationwide elemental concentrations in Chinese soil and newly published national average consumption of dietary foods, values of both transfer coefficients and discrimination factor (DF) for transfer from soil via the diet to both critical organs and the whole body have been calculated for important elements in radiation protection, including alkaline earths, alkali metals, rare earths and other related elements. These calculations have used both the United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR) model and the DF method. In the UNSCEAR model, the basic parameters used to describe the transport of radionuclides are the transfer coefficients P_i_j, which describe the relationship of concentrations or other amounts between compartment i and the following compartment j, whereas the DF is the ratio between the ...
2008-12-01
MICROMECHANICS - COMPRESSIVE PROPERTIES OF ...
... slenderness ratio. Equations which determine the ultimate compressive strength of a composite were established. Several ...
1965-05-01
International Nuclear Information System (INIS)
This paper provides information on heat transfer enhancement due to jet mixing inside a cylindrical enclosure. The work addresses conservative heat transfer assumptions regarding mixing and condensation that have typically been incorporated into passive containment design analyses. The current research presents an interesting possibility for increasing decay heat removal of passive containment systems under combined natural and forced convection. Eliminating these conservative assumptions could provide the basis for a change of containment design and reduce the construction cost. It is found that the ratio of forced- and free convection Nusselt numbers can be predicted as a function of the Archimedes number and a correlated factor accounting for jet orientation and enclosure geometry. To use the small-scale tests for large containment design, scale-up methods and criteria are important for matching the key governing parameters and fluid ...
2001-06-17
In vitro and in vivo analysis of pegulated Avidin
Energy Technology Data Exchange (ETDEWEB)
Full text: In 1995, we demonstrated the use of pretargetting three steps method and biotinylated tetracycline using radiolabelled {sup 99m}Tc-DTPA-biocytinamide for the detection of tumour cells in (C57B1/6 x BALB/C) F1 mice with E-3 thymoma. The three steps were (1) IP injection of biotinylated-tetracycline conjugate (1:1) ratio, (2) 96 hours later Avidin/Streptavidin was injected, and (3) 24 hours after (2), {sup 99m}Tc-biocytinamide -cDTPA was injected. Mice were sacrificed 16/24 h after (3) by cervical dislocation. Biodistribution of radioactivity tumour to blood, liver, bone were T:B1= 15.0, T:Li= 5.08, T:Bo=15.0. The percentage of injected dose per g was T= 3.15% and B1= 0.21%. To prolong circulation of Avidin and therefore its uptake into tumour, Avidin was covalently bound to polyethylene-glycol (PEG20 KD) at the molar ratio of PEG:Avidin 100:1 and 400:1. The pegulated Avidin was then cleared from the circulation using ...
1997-09-01
The present study attempts to use hydrogen peroxide solution to humidify Ca(OH)(2) particles to enhance the absorption of SO(2) to achieve higher removal efficiency and to solve the valuable reuse of the reaction product in the semidry flue gas desulfurization (FGD) process. Experiments were carried out to examine the effect of various operating parameters including hydrogen peroxide solution concentration, Ca/S molar ratio and approach to adiabatic saturation temperature on SO(2) removal efficiency in a laboratory scale spray reactor. The product samples were analyzed to obtain semi-quantitative measures of mineralogical composition by X-ray diffraction (XRD) with reference intensity ratio (RIR) method and the morphology of the samples was examined by scanning electron microscope (SEM). Compared with spraying water to humidify Ca(OH)(2), SO(2) removal efficiency was improved significantly by spraying hydrogen peroxide solution of 1-3 wt.% to ...
2009-04-24
International Nuclear Information System (INIS)
One approach in the design of neutral oxotechnetium complexes is based on the simultaneous substitution of a tridentate dianionic ligand and a monodentate monoanionic coligand on a [Tc(V)O]"+"3 precursor. Following this ''mixed ligand'' concept, a novel "9"9"mTc complex with N,N-bis(2-mercaptoethyl)-N'N'-diethylethylenediamine as ligand and 1-octanethiol as coligand is prepared and evaluated as potential brain radiopharmaceutical. Preparation of the complex at tracer level was accomplished by using "9"9"mTc-glucoheptonate as precursor. The substitution was optimized and a coligand/ligand ratio of 5 was selected. Under this conditions the labeling yield was over 80% and a major product (with radiochemical purity > 80%) was isolated by HPLC methods and used for biological evaluation. Chemical characterization at carrier level was developed using the corresponding rhenium complex as structural model. The Re complex was also prepared by substitution method and ...
1998-08-01
Some important aspects of fragment angular momentum in medium energy fission of {sup 238}U
Energy Technology Data Exchange (ETDEWEB)
Independent isomeric yield ratios of {sup 131}Te, {sup 133}Te and {sup 134}I have been determined at five different energies in the range of 25-44 MeV alpha particle induced fission of {sup 238}U using radiochemical and gamma spectrometric techniques. From the independent isomeric yield ratios, fragment angular momenta (J{sub rms}) have been deduced using a statistical model analysis. The J{sub rms} were also calculated theoretically based on thermal equilibration of various collective modes after considering the occurrence of multichance fission. These data and the literature data for various fragments in the mass region 126-136 in {sup 238}U ({alpha},f), {sup 238}U (p,f) and {sup 238}U ({gamma},f) show the following important features: (i) Both the entrance channel excitation energy and input angular momentum affect the fragment angular momentum in the exit channel. (ii) There are two groups of fission products from the point of view of ...
1999-03-15
Safe detection of Co-60. New perspectives in contamination and clearance measurements
International Nuclear Information System (INIS)
Consistent application of a newly developed coincidence technique to determine activation products in the operation and demolition of nuclear facilities results in very new perspectives in contamination monitoring and clearance measurement of plant components. In particular, it is possible to avoid the critical spread of point-source Co-60 contamination, the so-called hot particles. The CCM (Cobalt Coincidence Measurement) technique includes the coincident detection of prompt-prompt gamma cascades with "6"0Co and other activation products ("1"1"0"mAg, "1"2"4Sb, "2"2Na) with low mass-specific limits for unrestricted clearance. Special features of the technique are the short measurement times, excellent signal-to-noise ratio, and focusing in space achieved. Compared to conventional integral gamma-measurements, the signal-to-background ratio can be improved by 1-2 orders of magnitude. The method can be employed especially where conventional ...
Magnetic properties of FePt nanodots formed by a self-assembled nanodot deposition method
International Nuclear Information System (INIS)
Fe_5_0Pt_5_0 nanodots dispersed in a SiO_2 film (Fe_5_0Pt_5_0 nanodot film) were formed by a self-assembled nanodot deposition (SAND) method in which Fe_5_0Pt_5_0 and SiO_2 are cosputtered in a high vacuum rf magnetron sputtering equipment. Fe_5_0Pt_5_0 pellets are laid on a SiO_2 target in a sputtering chamber to form the Fe_5_0Pt_5_0 nanodot film in the SAND method. The size and density of Fe_5_0Pt_5_0 nanodot were controlled by changing the ratio of the total area of Fe_5_0Pt_5_0 pellets to that of SiO_2 target. The Fe_5_0Pt_5_0 nanodot size decreases and its density increases when the ratio decreases. As-deposited Fe_5_0Pt_5_0 nanodots self-assembled to a face-centered-cubic phase of single-crystal structure. The Fe_5_0Pt_5_0 nanodot films were annealed to evaluate the nanodot size controllability, the magnetic anisotropy, and the thermal stability. Fully ordered L1_0 face-centered-tetragonal Fe_5_0Pt_5_0 nanodots with ...
2006-08-07
Heat transfer augmentation for high heat flux removal in rib-roughened narrow channels
International Nuclear Information System (INIS)
Heat transfer augmentation in narrow rectangular channels in a target system is a very important method to remove high heat flux up to 12 MW/m"2 generated at target plates of a high-intensity proton accelerator of 1.5 GeV and 1 mA with a proton beam power of 1.5 MW. In this report, heat transfer coefficients and friction factors in narrow rectangular channels with one-sided rib-roughened surface were evaluated for fully developed flows in the range of the Reynolds number from 6,000 to 1,00,000; the rib pitch-to-height ratios (p/k) were 10,20 and 30; the rib height-to-equivalent diameter ratios (k/De) were 0.025, 0.03 and 0.1 by means of previous existing experimental correlations. The rib-roughened surface augmented heat transfer coefficients approximately 4 times higher than the smooth surface at Re=10,000, p/k=10 and k/De=0.1; friction factors increase around 22 times higher. In this case, higher heat flux up to 12 MW/m"2 ...
2001-04-08
Heat transfer augmentation for high heat flux removal in rib-roughened narrow channels
Energy Technology Data Exchange (ETDEWEB)
Heat transfer augmentation in narrow rectangular channels in a target system is a very important method to remove high heat flux up to 12 MW/m{sup 2} generated at target plates of a high-intensity proton accelerator of 1.5 GeV and 1 mA with a proton beam power of 1.5 MW. In this report, heat transfer coefficients and friction factors in narrow rectangular channels with one-sided rib-roughened surface were evaluated for fully developed flows in the range of the Reynolds number from 6,000 to 1,00,000; the rib pitch-to-height ratios (p/k) were 10,20 and 30; the rib height-to-equivalent diameter ratios (k/De) were 0.025, 0.03 and 0.1 by means of previous existing experimental correlations. The rib-roughened surface augmented heat transfer coefficients approximately 4 times higher than the smooth surface at Re=10,000, p/k=10 and k/De=0.1; friction factors increase around 22 times higher. In this case, higher heat flux up to 12 ...
1997-03-01
Energy Technology Data Exchange (ETDEWEB)
Glycosaminoglycan synthesis was studied in cell populations of ultraviolet light-induced murine cutaneous fibrosarcoma cells under conditions of varying growth rates in vitro. After labeling with the precursors, /sup 3/H-glucosamine and /sup 35/SO/sub 4/, sulfated glycosaminoglycans recoverable by direct proteolysis of the culture monolayers increased approximately 5-fold on a per cell basis from sparsely populated, exponential cell cultures (greater than 85% of cells in S, G2, or M phases) to stationary cultures inhibited by high cell density (greater than 50% of cells in G1). Within this cell surface-associated material, the relative ratio of heparan sulfate to the chondroitin sulfates was approximately 60/40% under conditions of exponential growth; in the growth-arrested cultures, the reverse ratio was found. The substratum attached material, obtained from the flask surface after ethyl glycol bis(beta-aminoethyl ...
1985-08-01
Extraction-spectrophotometric determination of terbium in its mixture with lanthanum
International Nuclear Information System (INIS)
A spectrophotometric study of the extraction with isobutanol of rare-earth elements in the form of complexes with quinoilizarin and N-benzene-N-phenylhydroxylamine has been made. The purpose of the study is to find out whether this reaction can be used in determining the concentration of elements in the presence of other rare-earth elements. In determining the relationship between the pH and light absorption the pH of the solution is measured after the extraction. The extraction of complexes begins at pH approximately 4 and reaches a maximum at pH7-8 (for La) and pH6-9 (for Er). The complexes underge decomposition when pH of the solution increased. The composition of complex compounds is determined by spectrophotometric methods for isomolar series, molar ratios and from the slope of logarithmic plots. Under optimal conditions (pH7.5) aAd at the measured ratio of the component for each ion of rare-earth elements, the molar ...
1975-01-01
Energy Technology Data Exchange (ETDEWEB)
This research investigates experimentally mixed convection and heat transfer augmentation by forced jets in a large enclosure, at conditions simulating those of actual passive containment cooling systems and scales approaching those of actual containment buildings or compartments. The experiment was designed to measure the key parameters governing the heat transfer augmentation by forced jets and investigate the effects of geometric factors, including the jet diameter, jet injection orientation, interior structures, and enclosure aspect ratio. The tests cover a variety of injection modes leading to flow configurations of interest that contribute to reveal the nature of mixing and stratification phenomena in the containment under accident conditions of interest. The heat transfer of mixed convection can be predicted to be controlled by jet Archimedes number and geometric factors. Using a combining rule for mixed convection and appropriate forced and natural ...
2004-07-01
Energy Technology Data Exchange (ETDEWEB)
An experimental study was performed to provide the combustion and emission characteristics resulting from fuel-reactivity controlled compression ignition (RCCI) combustion mode utilizing dual-fuel approach in a light-duty, multi-cylinder diesel engine. In-cylinder fuel blending using port fuel injection of gasoline before intake valve opening (IVO) and early-cycle, direct injection of diesel fuel was used as the charge preparation and fuel blending strategy. In order to achieve the desired auto-ignition quality through the stratification of the fuel-air equivalence ratio ( ), blends of commercially available gasoline and diesel fuel were used. Engine experiments were performed at an engine speed of 2300rpm and an engine load of 4.3bar brake mean effective pressure (BMEP). It was found that significant reduction in both nitrogen oxide (NOx) and particulate matter (PM) was realized successfully through the RCCI combustion mode even without applying exhaust gas ...
2011-03-01
Effect of pitting corrosion on local strength of hold frames of bulk carriers (1st report)
Energy Technology Data Exchange (ETDEWEB)
Firstly, pitting corrosion observed on hold frames in cargo holds of bulk carriers which exclusively carry coal and iron ore has been investigated in detail. It was shown that the shape of the corrosion pits observed on them is a circular cone and the ratio of the diameter to the depth is in the range between 8 to 1 and 10 to 1, which is different from the trend observed for the bottom shell of the oil tanker where the ratio is in the range between 4 to 1 and 6 to 1. Secondly, a series of tensile tests has been conducted to investigate the effect of pitting corrosion on tensile strength of members. It was pointed out that the tensile strength decreases gradually and the total elongation decreases drastically with the increase of the thickness loss due to pitting corrosion. The reduction of the tensile strength of the members with pitting corrosion is larger than that of members with uniform thickness loss in terms of ...
2004-09-01
Energy Technology Data Exchange (ETDEWEB)
Objective. To compare turbo inversion recovery magnitude (TIRM) with standard T1-weighted (T1-W) and T2-weighted (T2-W) MR sequences in the very early detection of acute osteomyelitis in children. Materials and methods. In 15 children with osteomyelitis, 15 sets of T1-W spin-echo (SE) (TR/TE, 400-640/12-17), T2-W turbo spin-echo (TSE) (TR/TE/ETL, 3290-4465/112-120/11), and TIRM (TR/TE/TI, 4000-6120/60/160) images were acquired with a 1.0-T magnet. Contrast-to-noise (C/N) ratios and percentage of signal between lesion and normal bone marrow were analysed with a computer-assisted image analysing system in a region of interest (ROI). Results. In 13 of 15 patients, the absolute signal enhancement in a ROI on the TIRM images was better than on the T1-W SE and T2-W TSE images and in 14 of 15 cases, C/N ratios were also better on the TIRM images than on the other sequences. In the other cases, the TIRM signal was diagnostically equivalent. On the TIRM ...
1998-11-01
Cement-clay pastes for stabilization/solidification of 2-chloroaniline
International Nuclear Information System (INIS)
Immobilization of a model liquid organic pollutant, i.e. the 2-chloroaniline (2-CA), into a cement matrix using organoclays as pre-sorbent agents was investigated. Five cement-clay pastes were prepared with different nominal water-to-cement ratios (w/c=0.40, 0.25 and 0.15 wt/wt) and various amounts of waste (waste-to-cement o/c=0.20, 0.60 and 1.00 wt/wt); for comparison, a neat cement paste was also prepared. Dynamic leach tests were performed on solidified monoliths in order to assess the successful immobilization of the 2-CA. In monoliths at constant w/c ratio (0.40) the total amount of pollutant released increases with its initial content, and ranges from 15 to 35% with respect to it. By lowering w/c from 0.40 to 0.15 at constant o/c, the performances improved (<25% released). The microstructure of the hardened cement-clay pastes was characterized by quantitative X-ray diffraction (QXRD) and electronic microscopy ...
2004-01-01
Energy Technology Data Exchange (ETDEWEB)
Austenitic 316LN alloy was ion-irradiated using the unique Triple Ion Beam Facility (TIF) at ORNL to investigate radiation damage effects relevant to spallation neutron sources. The TIF was used to simulate significant features of GeV proton irradiation effects in spallation neutron source target materials by producing displacement damage while simultaneously injecting helium and hydrogen at appropriately high gas/dpa ratios. Irradiations were carried out at 80, 200, and 350 C using 3.5 MeV Fe{sup ++}, 360 keV He{sup +}, and 180 keV H{sup +} to accumulate 50 dpa by Fe, 10,000 appm of He, and 50,000 appm of H. Irradiations were also carried out at 200 C in single and dual ion beam modes. The specific ion energies were chosen to maximize the damage and the gas accumulation at a depth of {approximately} 1 {micro}m. Variations in microstructure and hardness of irradiated specimens were studied using transmission electron microscopy (TEM) and a nanoindentation ...
1997-09-01
Quantitative bone scintigraphy. A study in patients with prostatic carcinoma
International Nuclear Information System (INIS)
Quantitative bone scintigraphy was performed in patients with prostatic carcinoma before orchiectomy as well as two weeks, two and six months after operation. The count rate was recorded as serial gamma camera images over the lower thoracic and all lumbar vertebrae from 1 to 240 min and at 24 h after injection of "9"9"Tc"m-MDP. In almost all abnormal vertebrae an increased count rate was observed within one hour after injection. Most of the vertebrae which were considered normal at 4 h after injection, but had an increased 24h/4h ratio developed into abnormal vertebrae later in the study. The patients with normal bone scintigrams showed no change in "9"9Tc"m-MDP uptake during the study. The reproducibility of quantitative bone scintigraphy was found to be #+-# 7% (1 SD). In response to therapy, most of the patients with abnormal bone scintigrams showed an increase in count rate two weeks after operation ...
1985-06-02
Heat transfer augmentation through wall-shape-induced flow destabilization
Energy Technology Data Exchange (ETDEWEB)
Experiments on heat transfer augmentation in a rectangular cross-section water channel are reported. The channel geometry is designed to excite normally damped Tollmein-Schlichting modes in order to enhance mixing. In this experiment, a hydrodynamically fully developed flow encounters a test section where one channel boundary is a series of periodic, saw-tooth, transverse grooves. Free shear layers span the groove openings, separating the main channel flow from the circulating vortices contained within each cavity. The periodicity length of the grooves is equal to one-half of the expected wavelength of the most unstable mode. The remaining channel walls are flat, and the channel has an aspect ratio of 10:1. Experiments are performed over the Reynolds number range of 300 to 15,000. Streakline flow visualization shows that the flow is steady at the entrance, but becomes oscillatory downstream of an onset location. This location moves upstream with ...
1990-05-01
Fed-batch operation for bio-H{sub 2} production by Rhodopseudomonas palustris (strain 42OL)
Energy Technology Data Exchange (ETDEWEB)
Interest in renewable and clean energies such as hydrogen has increased because of the high level of polluting emissions, increasing costs associated with petroleum and the escalating problems of global climate change. In the presence of a light source, a microbial photosynthetic process provides a system for the conversion of some organic compounds into biomass and hydrogen. Using Rhodopseudomonas palustris as a cell-factory, hydrogen photo-evolution was investigated in a photobioreactor (PBR) irradiated either from one or two opposite sides. Irradiating the photobioreactor from only one side, in the presence of malic acid, a reactor hydrogen production of 2.786 l(H{sub 2}) PBR{sup -1} was achieved. When the PBR was irradiated from two opposite sides, hydrogen photo-evolution increased to 3.162 l(H{sub 2}) PBR{sup -1}. Experiments were carried out using inoculum from either the retardation or the exponential growth phases. ...
2009-12-15
Carbon beam irradiation of human monolayer cells
Energy Technology Data Exchange (ETDEWEB)
The effect of the heavy particle irradiation on cell survival is different from that of X-ray irradiation. In Japan, heavy particles will be applied to cancer patients in the near future. This study was performed to determine the effect that carbon particle irradiation exerts to human monolayer cells in vitro, in comparison with the effect of 200 kVp X-ray. Two human cell lines, HeLaS3 and RMUG, were used. The irradiation was carried out by the RIKEN ring cyclotron and 200 kVp X-ray. The experimental procedure is explained. Also split dose experiment was carried out by applying equally divided doses at intervals of 2 - 4 hours. The Bragg curve of 135 MeV/n carbon beam through the lucite plates with different thickness is given. Thus the different LETs were obtained. The survival curves for 200 kVp X-ray and the various LETs of carbon beam are shown. The curves became steeper, and Do values decreased with increasing LETs in both cell lines. The relative biological ...
1993-12-31
Anode length optimization in a modified plasma focus device for optimal x-ray yields
International Nuclear Information System (INIS)
The effect of anode length and operating gas pressure on the x-ray emission from a nitrogen-filling modified plasma focus device has been investigated. The time-resolved investigation of x ray was carried out by using a five-channel photodiode x-ray spectrometer. The maximum x-ray yield is seen to increase with the increase in the anode length from 110 to 125 mm. Further increase in the anode length to 130 mm causes the x-ray yields to decrease. The highest x-ray yield of 4.5 J into 4#pi# sr was found for 125 mm anode length, which is 0.2% of the input energy. The average x-ray photon energy was estimated by using half-value thickness method and found to be 8.4 keV. The electron temperature of the plasma was estimated to be around 3 keV by x-ray intensity ratio method. The space-resolved x-ray-emitting zones for all the anodes were captured by a pinhole-based x-ray imaging camera and the images were ...
2006-01-01
Energy Technology Data Exchange (ETDEWEB)
This work proposes an innovative blend of potassium carbonate (K{sub 2}CO{sub 3}) and piperazine (PZ) as a solvent for CO{sub 2} removal from combustion flue gas in an absorber/stripper. The equilibrium partial pressure and the rate of absorption of CO{sub 2} were measured in a wetted-wall column in 0.0 to 6.2 m K{sup +} and 0.6 to 3.6 m PZ at 25 to 110 C. The equilibrium speciation of the solution was determined by {sup 1}H NMR under similar conditions. A rigorous thermodynamic model, based on electrolyte non-random two-liquid (ENRTL) theory, was developed to represent equilibrium behavior. A rate model was developed to describe the absorption rate by integration of eddy diffusivity theory with complex kinetics. Both models were used to explain behavior in terms of equilibrium constants, activity coefficients, and rate constants. The addition of potassium to the amine increases the concentration of CO{sub 3}{sup 2-}/HCO{sub 3}{sup -} in solution. The buffer ...
2005-04-18
Effects of human serum on bacterial competition with neutrophils for molecular oxygen.
A dialyzable factor(s) in human serum is known to stimulate gonococcal oxygen consumption. Its effect on other human pathogens was investigated. A 10% serum solution increased peak O2 consumption for Escherichia coli and Staphylococcus aureus to 157% (P less than 0.05) and 199% (P less than 0.02), respectively, of their O2 consumption when suspended in Hanks balanced salt solution, compared with a 356% increase for Neisseria gonorrhoeae with serum. Dialyzed serum lacked stimulatory capacity. Bacteria, serum, and neutrophils are often incubated to evaluate neutrophil bactericidal activity. Samples of 10(8) N. gonorrhoeae, S. aureus, and E. coli turned resazurin colorless (anaerobic conditions, Eh less than -42 mV) after 7.4, 13.3, and 15.1 min, respectively. Because neutrophil formation of reactive oxygen intermediates requires ambient O2, the effect of live bacteria and serum on this process was explored. After 5 min of incubation of 10(8) N. ...
1986-06-01
X-ray study of CuGa_xIn_1_-_xSe_2 solid solutions
International Nuclear Information System (INIS)
The semiconducting compound CuGa_xIn_1_-_xSe_2 crystallizes in the chalcopyrite structure (space group Ianti 42d, Z=4). The X-ray powder data for x=1, 0.75, 0.6, 0.5, 0.4, 0.25 and 0.0 have been collected and it is found that the lattice parameters a and c and their ratio c/a vary linearly with x. Thus the composition of any chalcopyrite in the pseudo-binary system CuGaSe_2 and CuInSe_2 can be obtained from the accurate lattice parameters. The crystallite size determined from the (112) plane is minimum for x=0.50 (#propor to#1000 A) and away from x=0.50 it increases. A value of u=0.240 (5) has been established for fixing, the Se-atom positions in the CuGa_0_._5In_0_._5Se_2 solid solution. The JCPDS Diffraction File No. for CuInSe_2 is 40-1487 and for CuGa_0_._5In_0_._5Se_2 is 40-1488. (orig.).
1989-12-01
Turbulent heat transfer augmentation using microscale disturbances inside the viscous sublayer
Energy Technology Data Exchange (ETDEWEB)
The authors report here on an experimental study of heat transfer augmentation in turbulent flow. Enhancement strategies employed in this investigation are based on the near-wall mixing processes induced in the sublayer through appropriate wall and near-wall streamwise-periodic disturbances. Experiments are performed in a low-turbulence wind-tunnel with a high-aspect-ratio rectangular channel having either (a) two-dimensional periodic microgrooves on the wall, or (b) two-dimensional microcylinders placed in the immediate vicinity of the wall. It is found that microdisturbances placed inside the sublayer induce favorable heat-transport augmentation with respect to the smooth-wall case, in the near-analogous momentum and heat transfer behavior are preserved; a roughly commensurate increase in heat and momentum transport is termed favorable in that it leads to a reduction in the pumping power penalty at fixed heat removal rate. The study shows ...
1992-05-01
Energy Technology Data Exchange (ETDEWEB)
The report addresses the application of reverse osmosis to the treatment of radioactive liquid waste, focusing on the effects of non-radioactive cations and anions, existing in radioactive waste, on the removal of radioactive nuclides. The bivalent cations are generally about ten times as high in decontamination factor as monovalent ones. In the case of anions, the factor of SO{sub 4}{sup 2-} is about ten times that of Cl{sup -} while that of NO{sub 3}{sup -} is somewhat smaller than that of Cl{sup -}. During permeation through membrane, anions tend to accompany cations, and the decontamination factor of accompanying ions is found to increase with that of the paring ions. These results indicate that if one can select components that will remain in the liquid waste, one should consider their effects on the efficiency of its treatment. Furthermore, the interaction between two anions or between two cations can be approximated by a linear equation consisting of the ...
1991-01-01
Treatment of radioactive liquid waste by reverse osmosis
International Nuclear Information System (INIS)
The report addresses the application of reverse osmosis to the treatment of radioactive liquid waste, focusing on the effects of non-radioactive cations and anions, existing in radioactive waste, on the removal of radioactive nuclides. The bivalent cations are generally about ten times as high in decontamination factor as monovalent ones. In the case of anions, the factor of SO_4"2"- is about ten times that of Cl"- while that of NO_3"- is somewhat smaller than that of Cl"-. During permeation through membrane, anions tend to accompany cations, and the decontamination factor of accompanying ions is found to increase with that of the paring ions. These results indicate that if one can select components that will remain in the liquid waste, one should consider their effects on the efficiency of its treatment. Furthermore, the interaction between two anions or between two cations can be approximated by a linear equation consisting of the logarithm of the decontamination ...
Transpiration and hydraulic traits of old and regrowth eucalypt forest in southwestern Australia
British Library Electronic Table of Contents (United Kingdom)
We tested the hypothesis that overstorey of eucalypt forest dominated by tall, large diameter trees uses less water than regrowth stands in the high rainfall zone (>1100mmyear^-^1) of the northern jarrah (Eucalyptus marginata) forest in southwestern Australia. We measured leaf area, cover, sapwood area and sapwood density at three paired old and regrowth stands. We also measured sapflow velocity at one paired stand (Dwellingup) from June 2007 to October 2008. Old stands had more basal area but less foliage cover, less leaf area and slightly thinner sapwood. The ratio of sapwood area to basal area decreased markedly as tree size increased. Sapwood area of the regrowth forest stands (6.6+/-0.30m^2ha^-^1) was nearly double that of the old stands (3.4+/-0.17m^2ha^-^1), despite larger basal are...
2010-01-01
Thermal stress cracking and the enhancement of heat extraction from fractured geothermal reservoirs
Given sufficient time, the extraction of heat from geothermal reservoirs formed by the hydraulic fracturing of competent rock will eventually result in the formation of thermal stress cracks in the reservoir. These cracks penetrate the rock in a manner such that the penetration-to-spacing ratio is approximately one. The penetration depends upon the extent of cooling and the square root of time. Initially then, the cracks are closely spaced and penetrate but little, so that a crazing pattern is apparent; but with increasing time some of these cracks, now more widely spaced, grow deeper. Eventually these larger cracks attain a critical aperture such that significant rates of water flow can be established within them and thus the newly created heat transfer area becomes useful for heat extraction. At the same time that cracks are forming within the main reservoir, thermal cracking also occurs in the wellbores that communicate with the reservoir. ...
1978-04-01
Thermal conductivity of sintered lithium orthosilicate compacts
International Nuclear Information System (INIS)
The design of solid breeder blankets is strongly affected by the low values of thermal conductivity and density of ceramic breeder pebble beds. A significant rise of both quantities would enhance the thermal performance and lead to an increased tritium breeding ratio. In order to improve these quantities pretreated lithium orthosilicate pebble material was dry pressed and subsequently sintered. The thermal conductivity of cylindrical pellets was determined by the heat pulse method using a laser flash device. A pebble bed characteristic sample was also investigated in order to check the measurement accuracy in comparison with previous results. Furthermore, two samples of low density cellular ceramics were also prepared by infiltration of polymer foams with a ceramic slurry. The thermal conductivity results show that the values are affected both by the particle size and the sample density. Thermal conductivity values of higher than 2 W/m K were ...
2009-04-30
Water transport in conifers occurs through single-celled tracheids that are connected to one another via intertracheid pit membranes. These membranes have two components: the porous margo, which allows water to pass through the membrane, and the impermeable torus, which functions to isolate gas-filled tracheids. During drought, tracheids can become air filled and thus hydraulically dysfunctional, a result of air entering through the pit membrane and nucleating cavitation in the water column. What are the hydraulic tradeoffs associated with cavitation resistance at the pit level, and how do they vary within the structural components of the intertracheid pit? To address these questions, we examined pit structure in 15 species of Cupressaceae exhibiting a broad range of cavitation resistances. Across species, cavitation resistance was most closely correlated to the ratio of the torus to pit aperture diameter but did not vary systematically with margo porosity. ...
2010-08-15
The Mid-Infrared Narrow Line Baldwin Effect Revealed by Spitzer
We present our discovery of a narrow-line Baldwin effect, an anti-correlation between the equivalent width (EW) of a line and the flux of the associated continuum, in 5-20$\\mu$m mid-infared lines from a sample of 68 Active Galactic Nuclei (AGN), located at z$<$0.5, observed with the Infrared Spectrograph on the {\\it Spitzer Space Telescope}. Our analysis reveals a clear anti-correlation between the EW of the [SIV] 10.51$\\mu$m, [NeII] 12.81$\\mu$m, and [NeIII] 15.56$\\mu$m lines and their mid-IR continuum luminosities, while the Baldwin effect for [NeV] 14.32$\\mu$m is not as obvious. We suggest that this anti-correlation is driven by the central AGN and not circumnuclear star formation in the host galaxy. We also find that the slope of the narrow-line Baldwin effect in the mid-infrared does not appear to steepen with increasing ionization potential. Examining the dependence of the EW to the Eddington Ratio ($L/L_{Edd}$) we find no strong ...
2008-01-01
Energy Technology Data Exchange (ETDEWEB)
Using standard brass alloy samples, an approach to reduce the laser-induced breakdown spectroscopy measurement uncertainty was tested and proved. Two important parameters for plasma characterization, the plasma temperature and the electron density, were applied to minimize the signal uncertainties due to uncontrollable experimental parameter variations. Results show that for the pulse-to-pulse analysis, the signal fluctuations can be significantly reduced by utilizing the plasma characteristic information. The major source for the single pulse fluctuations is the redistribution of the characteristic line at different temperatures according to the Boltzmann distribution under LTE. The change of the degree of ionization also contributes to the signal fluctuations. For the multi-pulse analysis, due to the nonlinear relationship between the plasma temperature and the line intensity, it is not applicable to utilize the Boltzmann distribution to reduce the influences of the plasma ...
2010-07-15
Study of Bs-> \\phi l^+ l^-$ Decay in a Single Universal Extra Dimension
Utilizing form factors calculated within the light-cone sum rules, we have evaluated the decay branching ratios of $B_s\\to \\phi\\gamma$ and $B_s\\to \\phi \\ell^+\\ell^-$ in a single universal extra dimension model (UED), which is viewed as one of the alternative theories beyond the standard model (SM). For the decay $B_s \\to \\phi \\ell^+\\ell^-$, the dilepton invariant mass spectra, the forward-backward asymmetry, and double lepton polarization are also calculated. For each case, we compared the obtained results with predictions of the SM. In lower values of the compactification factor 1/R, the only parameter in this model, we see the considerable discrepancy between the UED and SM models. However, when 1/R increases, the results of UED tend to diminish and at $1/R = 1000 \\mathrm{GeV}$, two models have approximately the same predictions. Compared with data from CDF of $B_s \\to \\phi \\mu^+ \\mu^-$, the 1/R tends to be larger than $350 ...
2011-01-01
The hazards of smoking in relation to lung cancer can never be over emphasized. In recent times shortly after Ebonyi State was created in 1996, the capital territory has increasingly been polluted by either quarry operators, motorcycle (Okada) riders or reckless cigarette smokers and bush burning. To investigate the havoc caused by all these on people, questionnaire was distributed among smokers and non smokers in various areas of specialization and habitations. In measuring the significance of association and the degree of association, a chi2 test and odds ratio method of analysis was employed. The result of the analysis showed that non-smokers do suffer lung cancer. It also revealed that the chances of a smoker to have lung cancer is 1.765 times higher than that of a non-smoker. Analysis also showed that lung cancer depends on age of smokers. It was later discovered that middle aged population are mostly affected, by the reason of chi2 ...
2009-04-01
Energy Technology Data Exchange (ETDEWEB)
Using a coplanar, end-mounted antenna as a baseline, various configuration trades were performed to select a preferred solid state concept. The increase in efficiency that could be realized by use of multi bandgap solar cells, either with klystron or solid state antenna was evaluated. Satellite configurations were developed to exploit the sandwich antenna concept wherein solar cells are located on one side of the antenna panel and solid state dc/RF converters on the other side. These concepts entailed various primary and secondary reflector arrangements for directing solar energy to the solar cell side of the antenna with higher concentration ratios than used on the coplanar configurations. Operations analysis included development of a satellite construction scenario, a concept for the SCB, a top-level satellite construction operation, construction operation, construction timelines and crew sizes, mass flows to orbit, and a satellite ...
1981-03-01
Resolution enhancement by subtraction of confocal signals taken at different pinhole sizes.
Subtractive imaging in confocal fluorescence light microscopy is based on the subtraction of a suitably weighted widefield image from a confocal image. An approximation to a widefield image can be obtained by detection with an opened confocal pinhole. The subtraction of images enhances the resolution in-plane as well as along the optic axis. Due to the linearity of the approach, the effect of subtractive imaging in Fourier-space corresponds to a reduction of low spatial frequency contributions leading to a relative enhancement of the high frequencies. Along the direction of the optic axis this also results in an improved sectioning. Image processing can achieve a similar effect. However, a 3D volume dataset must be acquired and processed, yielding a result essentially identical to subtractive imaging but superior in signal-to-noise ratio. The latter can be increased further with the technique of weighted averaging in Fourier-space. A comparison ...
2003-01-01
International Nuclear Information System (INIS)
Type 304 stainless steels (solution annealed material, cold worked material and fine grain material) were neutron irradiated to 3 x 10"2"5n/m"2 at 290degC and at 50degC. Each specimen was examined by SSRT test in high temperature water with 8 ppm dissolved oxygen and Ar gas environments. Results were as follows: (1) IASCC susceptibility of each material can be classified by 0.2% proof stress (PS) obtained from SSRT test in Ar gas: No IASCC susceptibility was observed in the PS range 850 MPa. (2) The uniform elongation (UE) in Ar gas environment decreased with increasing PS up to 800 MPa, and became about 0% in the PS range >800 MPa. (3) It was suggested that IASCC did not occur even if material had IASCC susceptibility, when under a condition that brittle fracture mechanism controls a specimen failure. (author)
2001-04-01
Reduced-aspect-ratio stellarator reactors
Energy Technology Data Exchange (ETDEWEB)
The extent to which the size of a modular stellarator reactor may be reduced is investigated by means of an analytic model of the reactor. The various means employed include varying the blanket/shield thickness, the power output and the wall loading. An optimum design is found, the major radius of which tends to be insensitive to changes in these quantities, although a decrease in the power output leads to a rather smaller decrease in reactor dimensions, as would be expected. Varying the plasma beta at fixed (iota/2..pi..)/sup 2/epsilon or, alternatively, increasing the rotational transform per field period, may, however, allow configurations with fewer field periods to be accessed which have a substantially smaller major radius than the 'standard case' adopted. The magnetics of various configurations required by the model are checked by field line following and the performance claimed is shown to be relatively easily achieved. Costs of two ...
1984-01-01
We investigated possible mechanism(s) where honokiol induces apoptosis in human hepatocellular carcinoma SMMC-7721 cells. MTT assay showed that honokiol has strong inhibition on SMMC-7721 cells in a dose-dependent manner. SMMC-7721 cells after honokiol treatment display morphological characteristics such as cell shrinkage, detachment from the culture plate, formation of apoptotic bodies, change to a round shape, and marked nuclear condensation and fragmentation after 32258 staining. Cell apoptosis was measured by Annexin-V/PI staining and alternatively, by the subG0/G1 percentage of the cell cycle analysis followed by FACS. An obvious loss of ??(m) and a quick burst of ROS was detected when honokiol reached 4?g/ml, which was coincident with the high apoptosis percentage in our previous research. Up-regulation of Bax and down-regulation of Bcl-2 were observed, suggesting that honokiol-induced apoptosis was associated with reactive oxygen species (ROS) production and an ...
2009-03-17
International Nuclear Information System (INIS)
From the indoor radon problem arises a great challenge for the radiation protection of the population. The soil can be considered as the only source for high radon concentrations in buildings. The contribution of common building materials to high indoor concentrations with a range of 30 Bq/m"3 is negligible low. Therefore building materials for radon mitigation should be judged by their tightness against diffusive radon and not by their radon exhalation rate. Also isolation materials for mitigation should be radon tight. The radon diffusion coefficient describes the physical processes in relatively homogeneous samples. The diffusion coefficient D and the diffusion length R are very exactly determined by a self engineered measuring method. The range of D reaches from D = (0.0005 to 2.35) . 10"-"6 m"2/s for building materials and from D = (0.07 to < 10"-"6) . 10"-"6 m"2/s for isolation materials. Applicable mitigation measures like increased ventilation rates, ...
British Library Electronic Table of Contents (United Kingdom)
We evaluated the use of a novel gene porter (Den123-a nontoxic self-assembled dendritic spheroidal nanoparticle made of biodegradable monomers), aiming to enhance and improve the desired immune response in protection from allergy. Footpad DNA immunization in Balb/c mice was done three times using the Bet v 1a gene with or without Den123 with 2-week intervals followed by sensitization with rBetv1 (5mg) in alum twice in a weekly interval. Different doses of pCMV-Betv1 were used (10mg and 100mg). The protective role of different formulations was evaluated by measuring the IgG1, IgG2a and IgE antibody production, cytokine release of isolated splenocytes and b-hexosaminidase release from the RBL cells. Higher and increasing ratios of IgG2a/IgG1 were seen in mice which received plasmids in combi...
2006-01-01
Energy Technology Data Exchange (ETDEWEB)
The analysis described demonstrates the use of benefit/cost sensitivity analysis in examining the wide range of potential damages and savings associated with converting oil-fired electric utility boilers to burn coal in Florida. This model, for the first time incorporates, in quantitative terms, environmental economic externalities into a benefit/cost ratio sensitivity analysis framework. Five different dose-response estimates of morbidity and mortality costs, property devaluation, and willing-to-pay estimates are used in combination with four acid rain dose-response models to estimate the net present worth of externality costs. The model estimates the net present worth of benefits by incorporating into a dynamic framework all relevant construction, O + M, and fuel costs of converting an electrical generation facility from using oil to coal. These benefits of fuel savings are then weighted against various combinations of externality costs associated with ...
1984-01-01
Optimization of neutron-to-light converter screens for use in real-time neutron radiography
International Nuclear Information System (INIS)
In neutron radiography, as in other forms of NDE, it is sometimes desirable to observe dynamic events. This need has generated increased interest in the development of real-time neutron radiography systems and neutron-to-light converter screens optimized for real-time application. Two screens currently available at MURR are: (1) a 0.041-cm-thick Gd_2O_2S screen manufactured by 3M Company and (2) a "6KiF-ZnS(Ag) screen (NE 426) manufactured by Nuclear Enterprises. These screens are presently used in conventional film neutron radiography and represent two of the commercially available screens that have demonstrated the greatest resolution and sensitivity. Unfortunately, these screens have severe limitations when used for real-time neutron radiography. In order to isolate and minimize the factors contributing to these limitations, several neutron absorbers and phosphorus were studied at MURR. The screen thickness and the neutron absorber/phosphorus weight ...
1982-04-01
On the orbital evolution and growth of protoplanets embedded in a gaseous disc
We present a new computation of the linear tidal interaction of a protoplanetary core with a thin gaseous disc in which it is fully embedded. For the first time a discussion of the orbital evolution of cores with eccentricity (e) significantly larger than the gas-disc scale height to radius ratio (H/r) is given. We find that the direction of orbital migration reverses for e>1.1H/r. This occurs as a result of the orbital crossing of resonances in the disc that do not overlap the orbit when the eccentricity is very small. Simple expressions giving approximate fits to the eccentricity damping rate and the orbital migration rate are presented. We go on to calculate the rate of increase of the mean eccentricity for a system of protoplanetary cores due to dynamical relaxation. By equating the eccentricity damping time-scale with the dynamical relaxation time-scale we deduce that an equilibrium between eccentricity damping and excitation through ...
1999-01-01
Natural gels: crystal-chemistry of short range ordered components in Al, Fe, and Si systems
Energy Technology Data Exchange (ETDEWEB)
In this review, the most important inorganic natural gels are presented: opal, aluminosilicate (allophanes) and hydrous iron oxides and silicates. It is demonstrated that natural gels are ordered at the atomic scale. In allophanes, Al is distributed between octahedral and tetrahedral sites. The amount of Al increases as Al/Si ratio decreases. Si-rich allophane have a local structure around Al and Si very different of that is known in kaolinite or halloysite. Transformation of Si-rich allophanes to crystallized minerals implies dissolution-recrystallization processes. On the contrary, in iron silicate with Fe/Si = 0.72, Si and Fe environments are close to those found in nontronite. The gel transformation to Fe-smectite may occur by long range ordering during ageing. In ferric silicate gels, the similarity of local structure around Fe in poorly ordered precursors and what is known in crystallized minerals suggests a solid transformation during ...
1997-07-01
NMR in highly correlated superconductors
International Nuclear Information System (INIS)
Results of our systematic NMR study in high T_c cuprates are reviewed. The antiferromagnetic spin fluctuations (AFSF) decrease in the order of La_1_._8_5Sr_0_._1_5CuO_4. YBa_2Cu_3O_7 and Tl_2Ba_2CuO_6_+_y. 1/T_1 of "6"3Cu in the CuO_2 plane in the normal state follows essentially a Curie-Weiss law at high temperature and T_1T = const. law at low temperature. The temperature dependence of 1/T_1 and the Knight shift together with their impurity effect in the superconducting state strongly suggest d-wave pairing implying the AFSF to be responsible for the occurrence of superconductivity. From the NQR frequency measurement the density of Cu 3d and O 2p holes decreases and increases, respectively, in the order of La, Y and Tl compounds, which is consistent with the change of AFSF. The relation between T_c and #nu#_Q, and their pressure dependence suggest that there exists and optimum value of the ratio of Cu 3d and O 2p hole density to give a ...
1992-08-01
Energy Technology Data Exchange (ETDEWEB)
The fuel-injection system of the Niigata 6L 16X-AG dual-fuel engine is structured to steadily supply injected fuel during diesel-engine operation, and to distribute oil at a low rate to all the cylinders during gas-engine operation. The dual-fuel engine is started by the diesel engine operation and is changed over to gas-engine operation when the load increases. This change over is done automatically with a link mechanism. Regarding the gas-supply system, the changing pressure of supply gas is controlled by a pressure control valve which is stable and most adequate for the engine. The dual-fuel engine has the following features: (1) a high compression ratio is adopted, which reduces fuel consumption and thermal efficiently; (2) if the supply of gas decreases or stops, while continuing loaded operations, it can immediately shift to diesel engine operation automatically and continue the operation; (3) ignition is done by the injection of pilot ...
1980-01-01
MEMS-based Speckle Spectrometer
We describe a new concept for a MEMS-based active spatial filter for astronomical spectroscopy. The goal of this device is to allow the use of a diffraction-limited spectrometer on a seeing limited observation at improved throughput over a comparable seeing-limited spectrometer, thus reducing the size and cost of the spectrometer by a factor proportional to r0/D (For the case of a 10 meter telescope this size reduction will be approximately a factor of 25 to 50). We use a fiber-based integral field unit (IFU) that incorporates an active MEMS mirror array to feed an astronomical spectrograph. A fast camera is used in parallel to sense speckle images at a spatial resolution of lambda/D and at a temporal frequency greater than that of atmospheric fluctuations. The MEMS mirror-array is used as an active shutter to feed speckle images above a preset intensity threshold to the spectrometer, thereby increasing the signal-to-noise ratio (SNR) of the ...
2006-01-01
Energy Technology Data Exchange (ETDEWEB)
Antitumor platinum(II) complexes derived from N-alkyl-propanediamine differing in the length of their carbon chain (C8, C10, C12 and C14) were incorporated in liposomes and the cytotoxic activity of these formulations was evaluated against tumor (A{sub 549}, MDA-MB-231, B16-F1 and B16-F10) and non-tumor (BHK-21 and CHO) cell lines. Stable and monodisperse liposome suspensions incorporating the platinum complexes were obtained from the lipid composition consisting of distearoyl-sn-glycero-3-phosphocholine, cholesterol and 1,2-distearoyl-sn-glycero- 3-phosphoethanolamine-N-(methoxy(polyethylene glycol)-2000) at 5:3:0.3 molar ratio. The entrapment efficiency (EE%) of the platinum complexes in liposomes increased with the carbon chain length. EE% was higher than 80% in C12- and C14-derivatives. The effect of liposome encapsulation on the cytotoxic activity of the complexes was found to depend on the carbon chain length. These data indicate that the ...
2010-07-01
International Nuclear Information System (INIS)
The photon rupture method, by which oxide film and metal are removed by focused pulsed Nd-YAG laser beam irradiation, was applied to form artificial micro-pits in Zn-5 mass% Al alloy-coated steel. The zinc alloy-coated layer was removed by pulsed laser irradiation treatment for about one second in a neutral buffer solution with NaCl. The rest potential transient with the laser treatment was measured. In the early stage of the laser treatment the rest potential of zinc alloy-coated steel changed to the negative direction immediately after every irradiation of a laser pulse and then returned to the previous value. However, after the steel substrate was exposed to the solution, the rest potential moved to the positive direction immediately after every irradiation of a laser pulse and then returned to the previous value. The amplitude and duration of the potential change after the laser irradiation increased with repetition of laser irradiation, related to the pit ...
2007-05-01
Immobilization of stationary phases onto chromatographic supports by gamma radiation
International Nuclear Information System (INIS)
Cobalt-60 gamma radiation has been found to be an effective means of immobilizing stationary phases onto gas and liquid chromatographic supports. The ability of a phase to crosslink was determined to be highly dependent on its chemical structure. Gamma radiation was employed to immobilize Se-30, a methylsilicone, and 216 PS onto Chromosorb WHP for packed column chromatography. The resultant columns exhibited increased thermal stability and a high degree of efficiency. Several blended phases containing varying ratios of Se-30:216 PS were also immobilized onto chromatographic packings. This work was further extended to the immobilization of Se-30 and 216 PS onto fused silica capillaries via gamma radiation. Columns exhibited excellent efficiency and improved thermal stability. An investigation into the role of immobilization of polymeric phases for HPLC was undertaken. Results indicate that gamma radiation can immobilzied polyoctadecylsiloxane ...
Energy Technology Data Exchange (ETDEWEB)
Semiconductive crystalline PZT powders doped with Bi and K were synthesized by hydrothermal reaction at 200{degree}C for 48 hours. The synthesis of the crystalline powders became difficult with an increase in doped amount of Bi and K, and in Zr/(Ti+Zr) ratio. Since substantial amounts of Pb remained in solution after hydrothermal reaction, the addition of Pb in excess of 25% was necessary to obtain the stoichiometric composition of the PZT solid solution. Bi contents in the powders were identical to those in starting materials, while K contents were less than expected ones. The electromechanical properties of the sintered bodies could be precisely measured by an admittance-curve-fitting method. The electromechanical coupling factor and piezoelectric coefficient of the sintered bodies varied with the Bi content like those of specimens prepared by solid state reaction, and showed the maximum values at a given Bi content. However, the change in ...
1989-10-01
Extended Gas in Seyfert Galaxies Near Infrared Observations of NGC 2110 and Circinus
We present results of near--IR long-slit spectroscopy in the J and K bands of the Seyfert 2 galaxies NGC 2110 and Circinus, investigating the gaseous distribution, excitation, reddening and kinematics. In NGC 2110, the emission line ratio [FeII]/Pa beta increases towards the nucleus (to ~ 7). The nuclear [Fe II]1.257 (microns) and Pa beta lines are broader (FWHM ~ 500 km/s) than the H2 (2.121) line (FWHM ~ 300 km/s). Both these results suggest that shocks, driven by the radio jet, are an important source of excitation of [Fe II]. The H2 excitation appears to be dominated by X-rays from the nucleus. In Circinus, both [FeII]/Pa beta and H2/Br gamma decrease from ~ 2 at 4 arcsec from the nucleus to nuclear values of ~ 0.6 and ~ 1, respectively, suggesting that the starburst dominates the nuclear excitation, while the AGN dominates the excitation further out (r > 2 arcsec). For both galaxies, the gaseous kinematics are consistent with circular ...
1998-01-01
Enhanced MALDI-TOF MS Analysis of Phosphopeptides Using an Optimized DHAP/DAHC Matrix
Selecting an appropriate matrix solution is one of the most effective means of increasing the ionization efficiency of phosphopeptides in matrix-assisted laser-desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS). In this study, we systematically assessed matrix combinations of 2, 6-dihydroxyacetophenone (DHAP) and diammonium hydrogen citrate (DAHC), and demonstrated that the low ratio DHAP/DAHC matrix was more effective in enhancing the ionization of phosphopeptides. Low femtomole level of phosphopeptides from the tryptic digests of ?-casein and ?-casein was readily detected by MALDI-TOF-MS in both positive and negative ion mode without desalination or phosphopeptide enrichment. Compared with the DHB/PA matrix, the optimized DHAP/DAHC matrix yielded superior sample homogeneity and higher phosphopeptide measurement sensitivity, particularly when multiple phosphorylated peptides were assessed. Finally, the DHAP/DAHC matrix was ...
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
The effect of transverse magnetic field parameter (Hartmann number, Ha) Reynolds number (Re) and Prandtl number (Pr) on the mixed convection flow past a semi-infinite vertical porous plate in a non-Darcian porous medium with variable viscosity and porosity, viscous dissipation and fluid-solid thermal conductivity ratio in the presence of plate transpiration (lateral mass flux) is investigated theoretically and numerically using Keller`s implicit finite difference scheme. It is shown that the Harmann number acts as a retarding force and increases the momentum boundary layer thickness, analogous to the flow against a positive pressure gradient, simultaneously decreasing local skin friction (shear stress). The heat transfer rate is however enhanced by the magnetic field (for positive values of the Eckert number) since the fluid is heated and temperature gradients become reduced between the fluid and the plate, with important potential applications ...
1997-01-01
Effects of focused-ion-beam irradiation on perpendicular write head performance
International Nuclear Information System (INIS)
The effects of focused-ion-beam (FIB) irradiation on writer performance were examined on a perpendicular recording system. The entire top pole was irradiated by FIB with ion doses from 0 to 300 pC/#mu#m"2. PW_5_0 and signal to noise ratio (SNR) were characterized using a spin stand before and after FIB irradiation. It was found that there is degradation of PW_5_0 and SNR due to FIB irradiation. At the maximum dose (300 pC/#mu#m"2), PW_5_0 increased by 33 nm (>30%) and SNR decreased by 5 dB (>25%). The degradation was attributed to the physical pole tip recession and the formation of a magnetic dead layer. The thickness of the magnetic dead layer was estimated by analyzing the write spacing loss. Using atomic force microscopy and stage current change monitored during FIB process, it was found that the entire 4-nm protective carbon layer was etched away with a dose of 25 pC/#mu#m"2. This result implies that the degradation with ion doses ...
2003-05-15
Effect of minor alloying element variation on the properties of Alloy 800
International Nuclear Information System (INIS)
Application of Alloy 800 in steam generator tubing of fast reactors, where continuous service temperature of the order of 550"0C is experienced, has been analyzed with respect to small variations in its chemical composition. Several laboratory melts of Alloy 800 have been prepared and their microstructural and mechanical property changes during simple aging and creep tests at 500 to 600"0C have been studied. It has been found that in the above temperature range precipitation of M_2_3C_6 on the grain boundaries is independent of the Ti : C ratio generally specified for Alloy 800. Gamma prime precipitation occurred in alloys containing as low as 0.5 percent Ti + Al after 1000 h of aging and was accompanied with a creep ductility decline. Upon #gamma# precipitation creep rate was retarded and its reacceleration for test times up to 8500 h at 550"0C was not observed. Based on the findings, increased Ti concentration at the expense of Al within the ...
Energy Technology Data Exchange (ETDEWEB)
Tensile specimens of the normalized and tempered fully martensitic steel DIN 1.4914 were helium implanted up to 340 appm within the temperature range 300-720/sup 0/C using a 104 MeV alpha particle beam. The high He/damage ratio of 1850 appm He/dpa allowed to determine the effect of helium on material properties. After irradiation tensile strength and ductility were investigated mainly at test temperatures equal to the irradiation temperatures. While short time irradiations with helium contents up to 100 appm have shown no visible effect on the tensile behaviour at all temperatures investigated, long time irradiations reduced the material strength at irradiation temperatures above about 440/sup 0/C. This irradiation induced softening obscured the predicted minor hardening effect of the observed He-bubbles completely and increases with irradiation time and temperature. The fracture mode of helium-implanted and control specimens is found to remain ...
1988-07-01
EVOLUTION OF MASSIVE STARS WITH PULSATION-DRIVEN SUPERWINDS DURING THE RED SUPERGIANT PHASE
International Nuclear Information System (INIS)
Pulsations driven by partial ionization of hydrogen in the envelope are often considered important for driving winds from red supergiants (RSGs). In particular, it has been suggested by some authors that the pulsation growth rate in an RSG can be high enough to trigger an unusually strong wind (or a superwind), when the luminosity-to-mass ratio becomes sufficiently large. Using both hydrostatic and hydrodynamic stellar evolution models with initial masses ranging from 15 to 40 M_s_u_n, we investigate (1) how the pulsation growth rate depends on the global parameters of supergiant stars and (2) what would be the consequences of a pulsation-driven superwind, if it occurred, for the late stages of massive star evolution. We suggest that such a superwind history would be marked by a runaway increase, followed by a sudden decrease, of the wind's mass-loss rate. The impact on the late evolution of massive stars would be substantial, with stars losing ...
2010-07-01
Dosimetric characteristics of backscattered electrons in lead
Energy Technology Data Exchange (ETDEWEB)
In electron beam therapy, tissue overdose due to electrons backscattered from lead has been profusely studied. To quantify this dose enhancement effect, an electron backscatter factor (EBF) wasdefined as the ratio of dose at the tissue-inhomogeneity interface with and without the scatterer present. The dependence of the EBF on energy at the scatterer surface is not well known for energies lower than 3 MeV which is the most frequent clinical situation. In this work, we have done Monte Carlo calculations with the GEANT code to study EBF in lead at this energy range. The applicability of this code and the developed procedure for dose estimation has been experimentally verified. The dependence of the EBF on the beam energy incident on the scatterer has been studied for different nominal beam energies incident at the phantom's surface. The results show a trend of increase of EBF with the beam energy incident on the scatterer between 0.5 and ...
2000-07-01
Energy Technology Data Exchange (ETDEWEB)
In case of airplane engine, technical development like increase of temperature at the turbine entrance or high speed rotation with a purpose of thrust up, and reduction of structural part single substance mass or reduction of number of parts in order to achieve lightness and so forth, has been promoted in order to improve the performance that is evaluated by thrust weight ratio (thrust/weight). Accordingly, research and development of high heat resistance, high strength, lightness and so forth of each material of the parts are in demand. As a representative material corresponding to such demand, L10 type {nu}-TiAl intermetallic compound which is light and has improved high temperature strength properties is paid attention and its development is promotes. The authors were successful for the first time in the world to manufacture composite material with CVD type SiC fiber that was difficult so far by using TiAl-Cr alloy having super plasticity at ...
1998-04-20
Corrosion in drilling and well stimulation
Energy Technology Data Exchange (ETDEWEB)
Corrosion in drilling and well stimulation is described in relation to acid corrosion inhibition, acid inhibitors, acetylenic inhibitors, synergistic blends, metallurgy, wellbore tubulars, coiled tubing, and high alloy tubular materials. Acidizing is a procedure for stimulating oil and gas wells. Factors that have an important influence on the reaction rate and the way in which acid reacts with rock include temperature, acid concentration, acid volume, injection velocity, acid viscosity, and fluid loss properties of the formation. The cost of drill pipe failures are $1 per fot of hole drilled, which is a significant fraction of the drilling cost. Steps in a test procedure are listed, as well as factors which determine the extent of acid corrosion in a given situation including acid type and strength, metal type, temperature, contact time; pressure, and volume/surface area ratio. Underbalanced drilling is a method for completing oil and gas wells that minimizes the ...
1999-07-01
Configurational diffusion of coal macromolecules
Energy Technology Data Exchange (ETDEWEB)
The objective of our research was to obtain fundamental information regarding the functional dependence of the diffusion coefficient of coal molecules on the ratio of molecule to pore diameter. That is, the objective of our study was to examine the effect of molecule size and configuration on hindered diffusion of coal macromolecules through as porous medium. To best accomplish this task, we circumvented the complexities of an actual porous catalyst by using a well defined porous matrix with uniform capillaric pores, i.e., a track-etched membrane. In this way, useful information was obtained regarding the relationship of molecular size and configuration on the diffusion rate of coal derived macromolecules through a pore structure with known geometry. Similar studies were performed using a pellet formed of porous alumina, to provide a link between the idealized membranes and the actual complex pore structure of real catalyst extrudates. The fundamental information ...
1991-01-01
Complete suppression of Pfirsch-Schlueter current in a toroidal l=3 stellarator
Energy Technology Data Exchange (ETDEWEB)
Pfirsch-Schlueter (P-S) current is an inherent property of a finite pressure toroidal equilibrium of tokamak and stellarator. However, it was pointed out recently (V.D. Pustovitov, Nuclear Fusion 36 (1996) 583) that the P-S current would be suppressed completely if the external vertical field could be adjusted to satisfy the condition {omega}=<{omega}> in an l=3 stellarator. Here {omega}=<B tilde{sup 2}>/B{sub 0}{sup 2}-2{epsilon} cos{theta}, l is a pole number, |B tilde| the vacuum helical magnetic field, B{sub 0} the toroidal field, {epsilon} the inverse aspect ratio, {theta} the poloidal angle and <...> denotes the average over the toroidal angle. An example of such a stellarator equilibrium is presented in this paper. For this stellarator equilibrium, behavior of rotational transform and Boozer magnetic spectrum is clarified when the pressure is increased. Both formation of helical magnetic axis and ...
1999-10-01
Comparison of digital and analogue data acquisition systems for nuclear spectroscopy
International Nuclear Information System (INIS)
In the present investigation the performance of digital data acquisition (DA) and analogue data acquisition (AA) systems are compared in neutron-induced fission experiments. The DA results are practically identical to the AA results in terms of angular-, energy- and mass-resolution, and both compare very well with literature data. However, major advantages were found with the digital techniques. DA allows for a very efficient #alpha#-particle pile-up correction. This is important when considering the accurate measurement of fission-fragment characteristics of highly #alpha#-active actinide isotopes relevant for the safe operation of Generation IV reactors and the successful reduction of long-lived radioactive nuclear waste. In case of a strong #alpha#-emitter, when applying the #alpha#-particle pile-up correction, the peak-to-valley ratio of the energy distribution was significantly improved. In addition, DA offers a very flexible expanded off-line analysis and ...
2010-12-21
Energy Technology Data Exchange (ETDEWEB)
The relationship between serum PG I, PG II levels and extent of atrophic gastritis was examined. The subjects were 64 patients (male: 32, female: 32, 51.9 years old on average) with established diagnosis of either atrophic gastritis or normal. In the X-ray gastric examination, Fuji Computed Radiography (FCR) was used to obtain clear-cut images of the gastric area. Concerning the serum PG I level, patients in the group with atrophic gastritis showed lower levels than those of the people in the group with no atrophic change, but the variation was wide, and no definite tendency was seen in the relationship between the atrophic change and the serum PG I levels. Concerning the serum PG II level, as the atrophic change progresses, the serum PG II level tended to increase gradually. A significant reduction in the PG I/II ratio was seen in the group with atrophic changes (p<0.01) in comparison with the group with no atrophic changes, and the PG I/II ...
1995-11-01
International Nuclear Information System (INIS)
The relationship between serum PG I, PG II levels and extent of atrophic gastritis was examined. The subjects were 64 patients (male: 32, female: 32, 51.9 years old on average) with established diagnosis of either atrophic gastritis or normal. In the X-ray gastric examination, Fuji Computed Radiography (FCR) was used to obtain clear-cut images of the gastric area. Concerning the serum PG I level, patients in the group with atrophic gastritis showed lower levels than those of the people in the group with no atrophic change, but the variation was wide, and no definite tendency was seen in the relationship between the atrophic change and the serum PG I levels. Concerning the serum PG II level, as the atrophic change progresses, the serum PG II level tended to increase gradually. A significant reduction in the PG I/II ratio was seen in the group with atrophic changes (p<0.01) in comparison with the group with no atrophic changes, and the PG I/II ...
1995-01-01
Coffee and tea consumption and endometrial cancer risk in a population-based study in New Jersey
British Library Electronic Table of Contents (United Kingdom)
We evaluated the role of tea and coffee and substances added (sugar/honey, creamers, and milk) on endometrial cancer risk in a population-based case?control study in six counties in New Jersey, including 417 cases and 395 controls. Multivariate odds ratios (OR) and 95% confidence intervals (CI) were computed using unconditional logistic regression. There was a moderate inverse association with coffee consumption, with an adjusted OR of 0.65 (95% CI: 0.36?1.17) for women who reported more than two cups/day of coffee compared to none. Tea consumption appeared to increase risk (OR: 1.93; 95% CI: 1.08?3.45), but after including the variables sugar/honey and cream/milk added to tea in the model, the risk estimate was attenuated and no longer statistically significant (OR: 1.77; 95% CI: 0.96?3.2...
2010-01-01
International Nuclear Information System (INIS)
The dependences of kinetic energies and peak profiles of multicharged ions of I "q"+ (q = 2-3) and C"2"+ on the laser intensity have been studied in detail by time-of-flight mass spectrometry, those multicharged ions are produced by irradiation of methyl iodide cluster beam with a nanosecond 532 nm Nd-YAG laser. Our experiments show that the kinetic energies released of multicharged ions increase linearly with the laser intensity in the range of 3 x 10"9-2 x 10"1"1 W/cm"2. The peaks of multicharged ions are split to forward ions and backward ions, and the ratio of the backward ions to forward ions decreases exponentially with laser intensity. The decreasing of backward ions is probably due to Coulomb scattering by the heavier I"+ ions when they turn around through the laser focus point. The linear dependence of kinetic energy of multicharged ions on laser intensity is interpreted by the ionization mechanism, in which the laser induced inverse ...
2006-03-20
Energy Technology Data Exchange (ETDEWEB)
Quantitative hepatic scintiangiography was previously used for evaluating the relative contribution of hepatic arterial and portal venous blood flows to the hepatic circulation. The present study compares 3 different procedures (automatic and manual integration, and slope fitting methods) for analyzing the hepatic time activity curves obtained after bolus i.v. injection of 370 MBq /sup 99m/Tc-diethylentriaminopentacetic acid. Twenty five subjects were studied: Five controls, ten cirrhotics, and ten portal hypertensive patients previously submitted to side to side portacaval anastomosis. The correspondence between results given by the different methods was satisfactory only in shunted patients, and the reproducibility of computed parameters was quite poor for all procedures. Accordingly, none of the methods can be considered as supporting reliable quantitative pathophysiological evaluations. However, the hepatic arterial/portal venous flow ratio was found to be ...
1989-04-01
Assembly of Linear Nano-Chains from Iron Oxide Nanospheres with Asymmetric Surface Chemistry
Besides the multifunctionality, another equally important aspect of nanoparticles is their engineerability to control the geometrical and chemical properties during fabrication. In this work, we exploited this aspect to define asymmetric surface chemistry of an iron oxide nanosphere by controlling the topology of ligand expression on its surface resulting in a particle with two faces, one displaying only amines and the other only thiols. Specifically, amine-functionalized iron oxide nanospheres were attached on a solid support via a crosslinker containing a disulfide bridge. Liberation of the nanosphere using thiolytic cleavage created thiols on the portion of the particle's surface that interacted with the solid support. Employing a solid-phase strategy and a step-by-step addition of particles, the two unique faces on the same nanosphere served as fittings to assemble them into linear nano-chains. Assembly of chains with various lengths and aspect ratios was ...
2011-01-06
Energy Technology Data Exchange (ETDEWEB)
Brain MRI was carried out in patients with chronic liver diseases. No abnormal findings were recognized in patients with chronic viral hepatitis, while 59.2% of cirrhotics showed a symmetrically strong signal in basal ganglia on T1 weighted image in MRI. This finding significantly related with lowered Fischer`s ratio of serum amino acid, increased levels of serum phenylalanine, tyrosine and hyaluronic acid, prolonged prothrombin time and decreased platelet counts in the peripheral blood. Overt hepatic encephalopathy was observed in 6 of 34 patients with the strong signal in MRI during follow-up period, while none of patients without that finding developed hepatic encephalopathy. These results have indicated that the strong signal in basal ganglia on MRI appears in cirrhotic patients with severe liver dysfunction, and it is an useful index in the early diagnosis of latent hepatic encephalopathy. An improvement of this MRI finding was not ...
1996-03-01
Ambient air pollution and congenital heart disease: a register-based study.
Maternal exposure to ambient air pollution has increasingly been linked to adverse pregnancy outcomes. The evidence linking this exposure to congenital anomalies is still limited and controversial. This case-control study investigated the association between maternal exposure to ambient particulate matter with aerodynamic diameter less than 10 ?m (PM(10)), sulfur dioxide (SO(2)), nitrogen dioxide, nitric oxide (NO), ozone (O(3)), and carbon monoxide (CO) and the occurrence of congenital heart disease in the population of Northeast England (1993-2003). Each case and control was assigned weekly average (weeks 3-8 of pregnancy) of pollutant levels measured by the closest monitor to the mother's residential postcode. Using exposure as both continuous and categorical variables, logistic regression models were constructed to quantify the adjusted odds ratios of exposure to air pollutants and the occurrence of each outcome group. We found exposure to ...
2011-02-17
Aggregation of silica nanoparticles directed by adsorption of lysozyme.
The interaction of the globular protein lysozyme with silica nanoparticles of diameter 20 nm was studied in a pH range between the isoelectric points (IEPs) of silica and the protein (pH 3-11). The adsorption affinity and capacity of lysozyme on the silica particles is increasing progressively with pH, and the adsorbed protein induces bridging aggregation of the silica particles. Structural properties of the aggregates were studied as a function of pH at a fixed protein-to-silica concentration ratio which corresponds to a surface concentration of protein well below a complete monolayer in the complete-binding regime at pH > 6. Sedimentation studies indicate the presence of compact aggregates at pH 4-6 and a loose flocculated network at pH 7-9, followed by a sharp decrease of aggregate size near the IEP of lysozyme. The structure of the bridged silica aggregates was studied by cryo-transmission electron microscopy (cryo-TEM) and small-angle ...
2011-07-20
International Nuclear Information System (INIS)
Techniques for reducing computation time in 3D photon dose calculations are addressed with specific emphasis given to the convolution/superposition approach. A single polyenergetic superposition model calculating absorbed dose per incident photon fluence (Gy cm"2) was developed in terms of TERMA and a total energy deposition kernel (a total point spread function). A novel approach was devised for reducing calculation time. The method, named the CF method, was based on the use of a conventional, fast model (here a modified power-law method was used) for the generation of 3D dose distributions on a fine dose matrix. Superposition calculations were carried out on a coarse matrix and calculation speed was increased simply by reducing the number of calculations. A set of correction factors was derived on the coarse grid from the ratio of the dose values from superposition to those from the conventional algorithm. These were interpolated onto the ...
1997-08-01
A numerical investigation of the aerodynamics of a furnace with a movable block burner
Scientific Electronic Library Online (English)
Abstract in english In this work the air flow in a furnace was computationally investigated. The furnace, for which experimental test data are available, is composed of a movable block burner connected to a cylindrical combustion chamber by a conical quarl. The apertures between the movable and the fixed blocks of the burner determine the ratio of the tangential to the radial air streams supplied to the furnace. Three different positions of the movable blocks were studied at this time. A thr (more) ee-dimensional investigation was performed by means of the finite volume method. The numerical grid was developed by the multiblock technique. The turbulence phenomenon was addressed by the RNG k-epsilon model. Profiles of the axial, tangential and radial velocities in the combustion chamber were outlined. The map of the predicted axial velocity in the combustion chamber was compared with a map of the experimental axial velocity. The internal space of the furnace was ...
2007-06-01
Petrophysical Analysis and Geographic Information System for San Juan Basin Tight Gas Reservoirs
Energy Technology Data Exchange (ETDEWEB)
The primary goal of this project is to increase the availability and ease of access to critical data on the Mesaverde and Dakota tight gas reservoirs of the San Juan Basin. Secondary goals include tuning well log interpretations through integration of core, water chemistry and production analysis data to help identify bypassed pay zones; increased knowledge of permeability ratios and how they affect well drainage and thus infill drilling plans; improved time-depth correlations through regional mapping of sonic logs; and improved understanding of the variability of formation waters within the basin through spatial analysis of water chemistry data. The project will collect, integrate, and analyze a variety of petrophysical and well data concerning the Mesaverde and Dakota reservoirs of the San Juan Basin, with particular emphasis on data available in the areas defined as tight gas areas for purpose of FERC. A relational, ...
2008-10-01
Optimum aspect ratio for heat transfer enhancement in curved rectangular channels
Enhanced heat transfer in curved rectangular channels depends on at least two geometric factors, the radius of curvature of the duct and the aspect ratio, which is the width/depth ratio of the duct. In this work, an expression for optimum aspect ratio is derived mathematically from a correlation that includes both aspect ratio and bend curvature parameters. Enhancement factors are developed that show optimal, near-optimal, and nonoptimal aspect ratios for curved rectangular ducts. Predicted enhancements are within 25% of published literature results for individual designs, two of which show heat transfer enhancement of 200% over that of a straight duct with turbulent flow. The theoretical maximum enhancement is shown to be about 480% over a straight-duct, turbulent-flow situation. This is not achievable in practice, but near-optimal solutions are achievable, yielding enhancements on ...
UK PubMed Central (United Kingdom)
The likelihood that past experience will produce correct guides to current practice depends on the signal-to-noise ratio for the clinical problem of interest. If the signal-to-noise ratio is high, the...Full Text Available
1996-01-01
Changes of magnetization transfer ratio according to rat brain development
International Nuclear Information System (INIS)
We assessed the age-related changes in magnetization transfer ratio (MTR) value and the ratio of water content in rat brain (frontal lobe and pons) during normal development. All studies were done on 42 normal Wistar rats. MTR was calculated by using the equation (M_o_f_f-M_o_n)/M_o_f_f, where M_o_f_f and M_o_n were the measured signal intensities on the conventional and MT-prepared SPGR images, respectively. The ratios of water content were measured by comparing the wet weight with the dry weight of the frontal lobe and the pons, which were extracted from a rat brain soon after MTR measurements. The ratio of water content was calculated by using the equation 100 x (wet weight-dry weight)/wet weight (%). The ratio of water content decreased markedly during the first 30 days, but the decrease was very slight there after both in the frontal lobe and the pons. The change in MTR was ...
Calculation of cosmic ray antiproton-proton ratio
Energy Technology Data Exchange (ETDEWEB)
Cross section parameterizations for antiproton production in pp collisions are used to predict the antiproton/proton ratio resulting from a flux of cosmic protons with energy spectral index of 2.6 interacting with a 5 gm/cm/sup 2/ column density of H. (GHT)
1980-01-01
Applications of BMI or BSI: Differences and Revisions According to Age and Height
UK PubMed Central (United Kingdom)
Validation of body-mass relationships requires a careful statistical analysis of data of normal weight individuals. BMI (ratio between body mass and square of body height) and BSI values (ratio between...Full Text Available
2010-01-01
Vibrational relaxation of a triatomic molecular impurity: D{sub 2}O in vitreous As{sub 2}S{sub 3}
Energy Technology Data Exchange (ETDEWEB)
Measurements of the relaxation of the D{sub 2}O stretch mode in vitreous As{sub 2}S{sub 3} are presented. Because the bending mode of the molecule offers an intra-molecular decay channel for the stretch mode, the decay scheme of the D{sub 2}O molecule is more complex than that of diatomic molecules. The asymmetric stretch mode of D{sub 2}O has a frequency of 2680 cm{sup -1}. To study the relaxation of this mode we applied a pump-probe technique, using intense psec; pulses of the Stanford Free Electron Laser. Due to the small cross-section of the vibrational mode, successful efforts were made to improve the signal to noise ratio by using a laser stabilization system and a tightly focused beam to increase the intensity, by averaging the signal with a kHz repetition rate and by using samples with an optimized D{sub 2}O concentration. A rapid relaxation rate on the order of 5 x 10{sup 9} sec{sup -1} at low temperature is found that ...
1995-12-31
International Nuclear Information System (INIS)
An efficient adsorption process is developed for the decontamination of trivalent chromium from tannery effluents. A low cost activated carbon (ATFAC) was prepared from coconut shell fibers (an agricultural waste), characterized and utilized for Cr(III) removal from water/wastewater. A commercially available activated carbon fabric cloth (ACF) was also studied for comparative evaluation. All the equilibrium and kinetic studies were conducted at different temperatures, particle size, pHs, and adsorbent doses in batch mode. The Langmuir and Freundlich isotherm models were applied. The Langmuir model best fit the equilibrium isotherm data. The maximum adsorption capacities of ATFAC and ACF at 25 deg. C are 12.2 and 39.56 mg/g, respectively. Cr(III) adsorption increased with an increase in temperature (10 deg. C: ATFAC-10.97 mg/g, ACF-36.05 mg/g; 40 deg. C: ATFAC-16.10 mg/g, ACF-40.29 mg/g). The kinetic studies were conducted to delineate the ...
2006-07-31
Time course of radiolabeled 2-deoxy-D-glucose 6-phosphate turnover in cerebral cortex of goats
Energy Technology Data Exchange (ETDEWEB)
The vivo dephosphorylation rate of 2-deoxy-D-glucose 6-phosphate (DGP) in the cerebral cortex of goats injected intravenously with radiolabeled 2-deoxy-D-glucose (DG) was investigated. Serial rapidly frozen samples of parietal cortical gray tissue were obtained at regular intervals over time periods from 45 min to 3 h in awake goats or in paralyzed and artificially ventilated goats maintained under 70% N/sub 2/O or pentobarbital sodium anesthesia. The samples were analyzed for glucose content and separate DG and DGP activities. The rate parameters for phosphorylation (k/sup *//sub 4/) and dephosphorylation (k/sup *//sub 4/) were estimated in each animal. The glucose phosphorylation rate (PR) was calculated over the intervals 3-5 (or 6), 3-10, 3-20, 3-30, and 3-45 min, assuming k/sup *//sub 4/ = O. As the evaluation period was extended beyond 10 min, the calculated PR became increasingly less when compared with that calculated over the 3- to 5- (or 6) min interval ...
1987-02-01
Energy Technology Data Exchange (ETDEWEB)
Small unilamellar vesicles which form when gel-state long-chain phosphatidylcholines are mixed with micellar short-chain lecithins undergo an increase in size as the long-chain species melts to its liquid-crystalline form. Analysis of the vesicle population with quasi-elastic light scattering shows that the particle size increases from 90-A radius to greater than 5000-A radius. Resonance energy transfer experiments show total mixing of lipid probes with unlabeled vesicles only when the Tm of the long-chain phosphatidylcholine is exceeded. This implies that the large size change represents a fusion process. Aqueous compartments are also mixed during this transition. 31P NMR analysis of the vesicle mixtures above the phase transition shows a great degree of heterogeneity with large unilamellar particles coexisting with oligo- and multilamellar structures. Upon cooling the vesicles below the Tm, the original size distribution (e.g., small ...
1989-10-03
Energy Technology Data Exchange (ETDEWEB)
Fourier transform infrared spectroscopy is a simple, fast, reliable and nondestructive analytical method. By using the method developed in Clark Atlanta University, consistent and reliable infrared spectral results can be obtained. An accurate radiant energy can be calculated from these infrared spectra by using a blackbody as the calibration standards. By means of the specially-designed-and-lab-made sampling inlet and the Horiba gas analyzers, the compositions of CO{sub 2}, CO, UCH, NOx and O{sub 2} etc. from the combustion exhaust gases have been on-line accurately analyzed. The commercial natural gas IR burner performed differently in the different conditions. For the methane-air combustion, at the equivalence ratio {Phi} = 1, the IR burner produced its maximum radiation efficiency, {approximately}31.4%, and the concentration of CO{sub 2} reached its maximum value, {approximately}10.7%. In the fuel-lean region, the O{sub 2} concentration in the emission gas ...
1997-03-31
Structure and catalysis of highly dispersed hydrodesulfurization catalysts
Energy Technology Data Exchange (ETDEWEB)
It is demonstrated that highly dispersed molybdenum sulfide catalysts are prepared by using Mo(CO){sub 6} adsorbed on the support. The structure of ultradispersed molybdenum sulfide is suggested by EXAFS techniques to be different from that of MoS{sub 2}. The TOF of the thiophene HDS is almost invariant with the dispersion of molybdenum sulfide at a high molybdenum dispersion, whereas the TOF of the hydrogenation greatly increases with increasing dispersion. On the basis of the HDS activity and optimum Co/Mo ratio of Co-Mo/Al{sub 2}O{sub 3} catalysts having a variety of molybdenum dispersion fabricated by using carbonyl complexes, it is demonstrated that highly active HDS catalysts are prepared by highly dispersing molybdenum sulfide phases. Edge decorations of molybdenum sulfides by cobalt are suggested for the synergy generation between cobalt and molybdenum sulfides. (orig.) [Deutsch] Unter Verwendung von auf dem Traeger ...
1994-12-01
Energy Technology Data Exchange (ETDEWEB)
Performance and emissions data were gathered on a normally aspirated single cylinder DI engine with various combinations of ceramic coatings installed. Thin ceramic thermal barrier coatings were applied to the piston crown and bowl, the head and valves, and the cylinder liner. The coated piston and head were run singly and in combination with the cylinder liner to investigate the effects of these different coated surfaces on emissions and performance. Coating the piston crown alone results in generally lower cylinder pressure, lower brake specific fuel consumption and lower NO(x) emission compared to the baseline engine. Soot emission is typically increased below 2000 RPM and decreased above 2000 RPM. Coating the head alone reduces cylinder pressure, but generally increases specific fuel consumption and NO(x) and soot emission. The KIVA-II code was used to model the Hydra engine with the thermal coatings. The computer modeling has led to an ...
1994-01-10
International Nuclear Information System (INIS)
In order to follow some of the changes induced by ultraviolet-B (UV-B, 280-320 nm) radiation in Phaseolus vulgaris and Brassica napus, experiments were designed to localize sites of changes in leaves and to correlate some of the physiological and biochemical changes with penetration of UV-B radiation. B.napus was exposed to 8.9 kJ m"-"2 day"-"1 biologically effective UV-B radiation (UV-B_B_E). The penetration of UV-B radiation into the leaf was followed using a quartz fibre optic microprobe. Monochromatic radiation at 310 nm was decreased by ca 50 and 34% in the adaxial and abaxial epidermis, respectively, in plants not exposed to UV-B, whereas the radiation was decreased by ca 70 and 42%, respectively, in the same region in UV-treated plants. Polychromatic radiation showed a wavelength dependent change mainly for the collimated radiation. The results correlated with the distribution of phenolic compounds analysed from 40 #mu#m paradermal leaf sections. The first adaxial section ...
1991-11-05
DEFF Research Database (Denmark)
Urinary acidification, bone metabolism and urinary excretion of calcium and citrate were evaluated in 10 recurrent stone formers with incomplete renal tubular acidosis (iRTA), 10 recurrent stone formers with normal urinary acidification (NUA) and 10 normal controls (NC). Patients with iRTA had lower plasma standard bicarbonate after fasting (P <0.01) and lower urinary excretion of titratable acid (P <0.05) and citrate (P <0.01) compared with NUA patients and NC, and higher urinary excretion of ammonia (P <0.05) compared with NC (P <0.05). Hypercalciuria was found in 6 of 10 patients with iRTA compared with 3 of 10 with NUA, and 0 of 10 NC. The citrate/calcium ratio in urine was significantly reduced in iRTA compared with the value in NUA (P <0.01), and in NUA compared with NC (P <0.05). Biochemical markers of bone formation (serum osteocalcin) and bone resorption (urinary hydroxyproline) were significantly increased in iRTA ...
1993-01-01
Multi-criteria evaluation of natural gas resources
International Nuclear Information System (INIS)
Geologically estimated natural gas resources are 500 Tcm. With the advance in geological science increase of estimated resources is expected. Natural gas reserves in 2000 have been proved to be around 165 Tcm. As it is known the reserves are subject to two constraints, namely: capital invested in the exploration and drilling technologies used to discover new reserves. The natural gas scarcity factor, i.e. ratio between available reserves and natural gas consumption, is around 300 years for the last 50 years. The new discovery of natural gas reserves has given rise to a new energy strategy based on natural gas. Natural gas utilization is constantly increasing in the last 50 years. With new technologies for deep drilling, we have come to know that there are enormous gas resources available at relatively low price. These new discoveries together wth high demand for the environment saving have introduced a new energy strategy ...
2007-01-01
Multi-criteria evaluation of natural gas resources
International Nuclear Information System (INIS)
Geologically estimated natural gas resources are 500 Tcm. With the advance in geological science increase of estimated resources is expected. Natural gas reserves in 2000 have been proved to be around 165 Tcm. As it is known the reserves are subject to two constraints, namely: capital invested in the exploration and drilling technologies used to discover new reserves. The natural gas scarcity factor, i.e. ratio between available reserves and natural gas consumption, is around 300 years for the last 50 years. The new discovery of natural gas reserves has given rise to a new energy strategy based on natural gas. Natural gas utilization is constantly increasing in the last 50 years. With new technologies for deep drilling, we have come to know that there are enormous gas resources available at relatively low price. These new discoveries together with high demand for the environment saving have introduced a new energy strategy ...
2007-01-01
Energy Technology Data Exchange (ETDEWEB)
Magnetothermal measurements up to 1600 K have been made on alloys in the ternary Ni-Mn-Sb system with a constant ratio Mn/Sb=1/1, to which belong the two ferromagnetic Heusler phases Ni/sub 2/MnSb with L2/sub 1/ structure and NiMnSb with C1/sub b/ structure. The susceptibility-temperature curves show the constitution of the vertical section. At high temperatures the susceptibilities obey a Curie-Weiss law. In the solid state the effective magneton number decreases with increasing Mn concentration from 4.9 (Ni/sub 2/MnSb) to 3.8 (NiMnSb). Simultaneously, on the transition from Ni/sub 2/MnSb to NiMnSb there is a strong increase of the susceptibility and of the Curie temperature from 292 to 686 K. In the heterogeneous range between 10 and 20 at.% Mn another phase part appears which is ferromagnetic at room temperature. By a heat treatment it undergoes a distinct development. In the liquid phase, the alloys can be characterized ...
1989-02-01
Inherited Sterility in Progeny of Gamma-Irradiated Spiny Bollworm, Earias Insulana Boisd
International Nuclear Information System (INIS)
The inherited sterility of the spiny bollworm Earias Insulana Boisd. Irradiated as parental male adults, with sub sterilizing doses of 100-200 Gy has been studied throughout three successive generations. In general, the female fecundity decreased at the three doses of irradiations (100, 150 and 200 Gy) throughout P_1. F_1, F_2 and F_3 generations as compared to control. The reduction was insignificant in all treatments with some exceptions at 200 Gy, in the parental generation and 150 and 200 Gy bin F_2 generation. Egg hatch of the parental generation was obviously reduced at 100, 150 and 200 Gy treatments as compared to the control. The progeny of F_1 males were evidently more sterile than their irradiated male parents. The effect continued in the F_2, population, however F_3 males almost regained their fertility. Irradiation of P_1 males did not greatly affect mating ability among P_1, F_1, F_2 and F_3 generations. The reduction in mating ability was significant only at 200 Gy for ...
1999-01-01
Energy Technology Data Exchange (ETDEWEB)
High productivity and high quality slab machine have been recently required in continuous casting process to lower the cost of steel production. It is important to know the inflow behavior of mold powder between mold and solidified shell to develop higher-speed casting. The purpose in this study is to make clear she mechanism of lubrication between mold and solidified shell. Sn-5mass%Pb alloy and stearic acid were used as substituted of liquid steel and molten mold powder in the experiment simulated continuous casting machine. Direct observation on inflow behavior of mold powder was made experimentally by a digital video camera. The friction force between mold and solidified shell was measured by a load cell which was set under the mold. Mold powder flowed into the aperture between mold and solidified shell during both positive strip time period and negative strip time period and the amount of powder consumption in positive strip time period was more than that in negative strip time ...
2000-06-01
Incompatibility of metam sodium with halogenated fumigants.
Metam sodium (metam) is a widely used soil fumigant. Combined application of metam and other available fumigants is intended to produce synergic pesticidal effects for a broad spectrum of pest control in soil fumigation. This study aimed to test the compatibility of metam with the halogenated fumigants 1,3-dichloropropene (1,3-D), chloropicrin, methyl bromide, methyl iodide and propargyl bromide. Halogenated fumigants and metam were spiked simultaneously into organic solvents, water and moist soils, and metam-induced degradation of these halogenated chemicals was evaluated. In all three media, the halogenated fumigants were incompatible with metam and degraded via rapid chemical reactions. The degradation rate varied with halogenated fumigant species and increased as the amount of metam present was increased. In moist soil, 15-95% of the halogenated fumigants were decomposed within 72 h by metam at a 1:1 molar ratio. ...
2005-05-01
Importance of neutron data in fission reactor applications
International Nuclear Information System (INIS)
The neutron data required to completely analyze fission reactors includes many isotopes and covers a broad energy range. In both fast and thermal reactors, the neutron inventory is a fine balance determined by the fission properties of "2"3"5U, "2"3"9Pu and "2"3"8U and by the capture cross sections of "2"3"8U, fuel materials, structural materials and coolant materials. In fast reactors, the spectrum of neutrons ranges from 1 keV to 3 MeV and is influenced by the elastic and inelastic scattering properties of "2"3"8U and the structural and coolant materials. For neutron shielding applications, the important neutron data include the total cross sections of structural and coolant materials in the MeV range. The impact of these basic nuclear data in fission reactor applications is most suitably described by sensitivity analysis. For example, sensitivity coefficients computed for a typical large plutonium fueled fast reactor indicate that a percent increase in the ...
1976-07-06
The occurrence of hybrid incompatibilities forms an important stage during the evolution of reproductive isolation. In early stages of speciation, males and females often respond differently to hybridization. Haldane's rule states that the heterogametic sex suffers more from hybridization than the homogametic sex. Although haplodiploid reproduction (haploid males, diploid females) does not involve sex chromosomes, sex-specific incompatibilities are predicted to be prevalent in haplodiploid species. Here, we evaluate the effect of sex/ploidy level on hybrid incompatibilities and locate genomic regions that cause increased mortality rates in hybrid males of the haplodiploid wasps Nasonia vitripennis and Nasonia longicornis. Our data show that diploid F(1) hybrid females suffer less from hybridization than haploid F(2) hybrid males. The latter not only suffer from an increased mortality rate, but also from behavioural and spermatogenic sterility. ...
2011-08-31
Facile synthesis and the sensitized luminescence of europium ions-doped titanate nanowires
International Nuclear Information System (INIS)
Europium (Eu) ions-doped titanate nanowires were synthesized via a sol-gel-hydrothermal chemistry and they were found to be roll multilayered trititanate-type nanowires intercalated with Eu3+ and alkali ions. The average diameter was about 20 nm for nanowires synthesized in NaOH solution and about 10 nm for nanowires synthesized in KOH solution. Under ultraviolet excitation the nanowires showed bright red emission corresponding to 5D0-7Fj of Eu3+ ions at room temperature, which was attributed to the non-radiative energy transfer from the surrounding Ti-O octahedral nanosheets to the central Eu3+ ions in interlayer. The luminescent properties of nanowires were influenced by the type of co-intercalated alkali ions, doping degree, hydrothermal and annealing temperatures. The intensity ratio of 5D0-7F2 to 5D0-7F1 of titanate nanowires intercalated with Eu3+ and Na+ ions was higher than that of titanate nanowires intercalated with Eu3+ and K+ ions. The emission ...
2009-04-15
Effects of reactor configuration on the performance of static-bed submerged media anaerobic reactors
Energy Technology Data Exchange (ETDEWEB)
Three different configurations of cylindrical submerged media anaerobic reactors (SMARs) with packing volumes of 85 items were operated at 35 C for 415 days with COD loading rates varying from 1 to 12 g/l/d and three retention times of 0.5, 1, and 2 days. A synthetic waste consisting of a milk solution with a mineral supplement was used for the feed. Tracer studies on clean-bed and dirty-bed SMARs indicate that reactor configuration, biogas mixing, and biomass accumulation all have a significant effect on SMAR hydraulics and cause short-circuiting. Based on the isothermal energy dissipation theory, the higher hydrostatic pressures resulting from higher SMAR heights increases self-induced biogas mixing and improves the contact efficiency between substrate and organisms. Based on TCOD removal rate, the tallest SMAR performed slightly better at COD loading rates above 4/g/l/d. At COD loading rates equal to or below 4 g/l/d, there was little difference in TCOD removal ...
1988-01-01
Effective laser luminescence of nanocomposites Eu(TTA)2(Ph3PO)2NO3-polyvinylpyrrolidone
International Nuclear Information System (INIS)
Thin films (1-10 ?m thickness) of nanocomposites (NC) based on organic coordinated compound (OCC) Eu(TTA)2(Ph3PO)2NO3 (where TTA is thenoyl trifluoroacetonate (C8H5F3O2S), Ph3PO - triphenylphosphine (C6H5PO) and polymer-polyvinylpyrrolidone ((C6H9NO)n) (PVP)) were obtained by chemical methods and with different molar ratios into organic polymer matrix. NC have been characterized by measurements of optical transmission, excitation spectra of photoluminescence (PL) and photoluminescence of NC at different concentrations of Eu(TTA)2(Ph3PO)2NO3 in NC. In the optical transmission of NC, the characteristic parameters of NC such as threshold absorbance, dependence on the concentration of the organic coordinated compound in NC, etc., have been determined The displacement of threshold absorption to infrared is observed with increasing of the concentration of the coordination material in NC. The excitation spectrum of photoluminescence of NC led the ...
2011-07-07
Distribution of polycyclic aromatic hydrocarbons in water and surface sediments from Daya Bay, China
International Nuclear Information System (INIS)
Findings indicate an urgent need to establish a monitoring program for persistent organic pollutants in water and sediment. - Marine culture is thriving in China and represents a major component of the regional economy in coastal zones, yet the environmental quality of many of those areas has never been studied. This paper attempts to investigate the quality status of Daya Bay, a key aquaculture area in China. The levels of 16 polycyclic aromatic hydrocarbons (PAHs) were determined in water and sediment samples of the bay. The total concentrations of 16 PAHs varied from 4228 to 29325 ng l"-"1 in water, and from 115 to 1134 ng g"-"1 dry weight in sediments. In comparison to many other marine systems studied, the PAH levels in Daya Bay waters were relatively high, and at six sites they were sufficiently high (>10 #mu#g l"-"1) to cause acute toxicity. The PAH composition pattern in sediments suggest dominance by medium to high molecular weight compounds, and the ...
2003-02-01
Differential expression of fatty acid uptake in 3T3-L1 cells
Energy Technology Data Exchange (ETDEWEB)
Cultured 3T3-L1 cells have been used as a model system to investigate the mechanism of fatty acid uptake by adipose tissue. Using a 1:1 molar ratio of /sup 14/C-oleate and defatted bovine serum albumin (BSA), fatty acid (FA) uptake was quantitated at 4/sup 0/ and 37/sup 0/ as cell associated radioactivity. The profile of FA uptake in preadipocytes and adipocytes was biphasic; an initial rapid phase (1-20s) followed by a second slower phase (60-480s). At 37/sup 0/ the initial rate of FA accumulation in preadipocytes was identical to that in adipocytes, whereas the rate of accumulation during the second phase increased 7-fold (100 ..mu..M total FA) as a consequence of adipose conversion. When uptake measurements were made at 4/sup 0/ in adipocytes, the initial rate was identical to that at 37/sup 0/, however the rate of second phase decreased 5-fold. Incubation of /sup 14/C-BSA and nonradiolabeled FA with adipocyte monolayers (100 ..mu..M total ...
1987-05-01
The distribution of mass-to-light ratio with radius in M31 and M33
International Nuclear Information System (INIS)
1974. Netherlands Baldwin, JE Cambridge Univ. (UK). Cavendish Lab. Reidel.;
Surface Crystallization and Composition of Spinel and Acmite in High-Level Waste Glass
Surface crystallization and surface-to-bulk ratio in high-level waste glasses.
2000-07-10
Quantitative bone scintigraphy in the evaluation of angular deformity of the lower extremity
International Nuclear Information System (INIS)
A technique for quantitative analysis of growth plates in varus or valgus deformity about the knee has been developed. Computer-generated regions of interest are placed on magnification scintigraphs to divide distal femoral and proximal tibial physes into four equal segments. The ratio of counts in the medial half to counts in the lateral half was studied in 31 children (22 normal, 9 with angular deformity). Normal ratios were 0.74 to 0.98 for femora and 0.98 to 1.20 for tibias. In eight of nine patients with deformity, the ratio was abnormal; in two patients the ratio returned to normal when the deformity ceased to progress.
Hollow Glass Filament Reinforced Plastics for Deep ...
... Problems investigated in various basic hollowness ratios include ultimate compressive strength, fatigue properties, buckling characteristics, and ...
1966-02-08
[Dependence of scattered Mn K alpha / K beta X-ray intensity ratio on the scatterer materials].
The K alpha / K beta ratio of Mn KX-rays scattered by metallic samples changed remarkably with the geometry between the sample and the (55)Fe source-Si(Li) detector system. On the contrary, this intensity ratio changed little in the cases of non-metallic scatterer samples such as lucite or mylar. This difference is interpreted as due to the occurrence of strong or weak interference in the coherent scattering photons. PMID:7280291
1980-10-01
Theory of isomer ratios of shape isomers in heavy ion induced reactions
A method for the calculation of excitation functions and isomer ratios, for shape isomers, in heavy ion induced reactions is proposed. The calculated values of excitation functions and isomer ratios agree very well with the experimental values for the reaction /sup 238/U(/sup 11/B, alpha 3n)/sup 242/Am. (auth)
1973-11-12
International Nuclear Information System (INIS)
Ksub(#beta#)/Ksub(#alpha#) X-ray intensity ratios have been measured for various elements between Z = 29 and Z = 79 for incident proton energies of 23.6, 32.1 and 43.6 MeV. The results yield no evidence for a variation in ratio with particle energy. (orig.).
1980-01-01
UK PubMed Central (United Kingdom)
Isotope ratios of cellulose and cellulose nitrate from aquatic Crassulacean acid metabolism (CAM) and non-CAM plants were determined. Cellulose oxygen istope ratios for all plants that grew together...Full Text Available
1984-09-01
International Nuclear Information System (INIS)
The Ksub(#beta#)/Ksub(#alpha# 12) x-ray intensity ratio of the Si K spectrum was measured for proton impact on Si0_2 in the energy range 300-800 keV. An energy dependence of the intensity ratio was found and an explanation is given in terms of multiple ionisation. (author).
1980-04-01
Energy Technology Data Exchange (ETDEWEB)
An estimate of the tritium dose to the public in the vicinity of the heavy water research reactor facility at AECL-Chalk River Laboratories, Ontario, Canada, has largely been accomplished from analyses on regularly-collected samples of air, precipitation, drinking water and foodstuffs (pasture, fruit, vegetables and milk) and environmental dose models. To increase the confidence with which public doses are calculated, tritium doses were estimated directly from the ratio of tritiated species in urine samples from members of the general public. Single cumulative 24 h urine samples from a few adults living in the vicinity of the heavy-water research reactor facility at Chalk River Laboratories, Canada were collected and analysed for tritiated water and organically bound tritium. The participants were from Ottawa (200 km east), Deep River (10 km west) and Chalk River Laboratories. Tritiated water concentrations in urine ranged from 6.5 Bq.l{sup -1} ...
2001-07-01
Hydrogen lines in the high-luminosity quasar B2 1225+31
International Nuclear Information System (INIS)
The emission lines H#alpha#, H#beta#+[OIII], and L#alpha# have been observed in the high-redshift quasar 1225+31. The ratios of line intensities in 1225+31 are found to be L#alpha#/H#alpha#approx.0.8, H#alpha#/(H#beta#+[OIII]) approx.4, and 4
Constraining SN Ia Models Using X-ray Spectra of Clusters of Galaxies
We present constraints on theoretical models of Type Ia SNe using spatially resolved ASCA X-ray spectroscopy of four galaxy clusters: Abell 496, Abell 2199, Abell 3571 & Perseus. All four clusters have central Fe abundance enhancements and an ensemble of abundance ratios are used to show that most of the Fe in the central regions of the clusters comes from SN Ia. At the center of each cluster, simultaneous analysis of spectra from all ASCA instruments shows that the Ni to Fe abundance ratio (normalized by the solar ratio) is ~ 4. We use the Ni/Fe ratio as a discriminator between SN Ia explosion models: the Ni/Fe ratio of ejecta from the "Convective Deflagration" model W7 is consistent with the observations, while those of "delayed detonation" models are not consistent at the 90% confidence level.
2000-01-01
Effects of compression ratio on combustion characteristics of a direct-injection diesel engine
Energy Technology Data Exchange (ETDEWEB)
The effects of compression ratio on the history of the fuel-burning process was investigated in a single-cylinder direct-injection diesel engine. Two compression ratios of 21.4 and 18.5 were studied by using two wide and shallow bowls. The engine was operated at different speeds and overall air-fuel ratios, but with constant start-of-combustion timing at top dead center. The measured cylinder pressure was used to derive fuel-burning rate. At all conditions, the low-compression-ratio bowl had a larger mass of premixed-burned fuel and a higher peak specific fuel-burning rate. The fuel-burning rate in the diffusion-controlled phase of combustion decreased with decreasing compression ratio. The resulting combustion duration became longer at reduced compression ratio, and the difference could be as large as 14 crank-angle degrees. For the engine conditions examined ...
1987-01-01
Integrated systems for control of pink bollworm in cotton
International Nuclear Information System (INIS)
Full text: Pink bollworm (PBW), Pectinophora gossypiella (Saunders), an introduced pest from Mexico, first occurred in United States cotton production in Texas in 1917. Unacceptable economic losses have occurred. The development of PBW sterile moth release technology, gossyplure sex pheromone behavioral control, cotton plant cultural control to reduce overwintered PBW populations, and the transfer of the insect toxin protein gene into cotton from Bacillus thuringiensis kurstaki (Berliner) have provided an effective integrated pest management (IPM) system with PBW eradication potential. Sterile insect release was considered a potential option for PBW population suppression in the early 1960s. Research on the isolated island of St. Croix, (US Virgin Islands) demonstrated its validity. Reductions of larval infestations in bolls following sterile moth releases began when ratios of released PBW sterile male to native male moths averaged 70:1 in gossyplurebaited traps. ...
2005-05-09
Energy Technology Data Exchange (ETDEWEB)
Purpose: {sup 31}P-MRS is used to assess the influence of sex and age on quadriceps muscle metabolism before and after exercise. Materials and Methods: 32 healthy volunteers (15 women, 17 men; mean age: 38{+-}17 yrs.) were examined by dynamic phosphorus-31 ({sup 31}P) magnetic resonance spectroscopy (MRS). In the magnet, the quadriceps muscle was stressed by an isometric and an isotonic form of exercise until exhaustion, respectively. Results: Resting conditions: With increasing subjects` age, the ratio {beta}-adenosine triphosphate/total phosphate decreased (r=-0.37; p=0.02). With increasing subjects` age, the ratios inorganic phosphate/phosphocreatine (r=0.79; p=5x10{sup -8}), phosphomonoester/{beta}-adenosine triphosphate (r=0.74; p=10{sup -6}) and phosphodiester/{beta}-adenosine triphosphate (r=0.62; p=10{sup -4}) increased. The pH was the only one of the evaluated spectroscopic ...
1999-05-01
Rare-earth doped (#alpha#'/#beta#')-sialon ceramics
International Nuclear Information System (INIS)
The objectives of this research were to investigate the possibility of controlling the #alpha#'/#beta#' phase ratio and morphology in Sialon ceramics. These objectives have been sought by the control of the starting composition, and by post sintering heat treatment. The main emphasis has been on the production of a series of #alpha#' and (#alpha#'+#beta#') Sialon ceramics with a minimum amount of the glass phase by the pressureless sintering technique and using ytterbium (Yb) as an #alpha#' stabilising element. The Yb additions were made via the oxide or the alumino- silicate presynthesised glass; the latter was found to improve the density. The XRD analysis of the as sintered materials revealed #alpha#' to be the dominant phase with minor contributions from #beta#' sialon and/ or 12H A1N polytype. Additions of SiO_2 or #beta#-Si_3N_4 were made to various materials to assess potential mechanisms for obtaining control over the microstructural development of ...
Energy Technology Data Exchange (ETDEWEB)
A computed tomography (CT) cut-off for differentiating neoplastic lesions (polyps/carcinoma) from normal colon in contrast-enhanced CT colonography (CTC) relating to the contrast phase and lesion size is determined. CT values of 64 colonic lesions (27 polyps <10 mm, 13 polyps {>=}10 mm, 24 carcinomas) were determined by region-of-interest (ROI) measurements in 38 patients who underwent contrast-enhanced CTC. In addition, the height (H) of the colonic lesions was measured in CT. CT values were also measured in the aorta (A), superior mesenteric vein (V) and colonic wall. The contrast phase was defined by xA + (1 - x)V using x as a weighting factor for describing the different contrast phases ranging from the pure arterial phase (x=1) over the intermediate phases (x=0.9-0.1) to the pure venous phase (x=0). The CT values of the lesions were correlated with their height (H), the different phases (xA + (1 - x)V) and the ratio [xA + (1 - x)V]/H. The CT ...
2004-12-01
International Nuclear Information System (INIS)
Perovskite-type cobaltates in the system La2Co1+z(MgxTi1-x)1-zO6 were studied for z=0?x?0.6 and 0?xoC. The space group symmetry of the structure changes from P21/n via Pbnm to R3-bar c with both increasing Mg content and increasing Co content. The La2Co(MgxTi1-x)O6 (z=0) compounds show anti-ferromagnetic couplings of the magnetic moments for the Co below 15 K for x=0, 0.1 and 0.2. XANES spectra show for the compositions 0?x?0.5 a linear decrease in the L3/(L3+L2) Co-L2,3 edge branching ratio with x, in agreement with a decrease of the average Co ion spin-state, from a high-spin to a lower-spin-state, with decreasing nominal Co2+ ion content. -- Graphical abstract: XRPD patterns for perovskite compounds along the lines La2Co(MgxTi1-x)O6 and La2Co1+z(Mg0.5Ti0.5)1-zO6. Display Omitted Research Highlights: ?Tuning of the oxidation state of Co in the perovskite system La2Co1+z(Mtem La2Co1+z(MgxTi1-x)1-zO6, z=0?x?0.6 and ...
2011-01-01
On the impact of low power density microwaves in some living tissues
Energy Technology Data Exchange (ETDEWEB)
The biomedical and ecological interest for the microwave impact on the Earth biosphere is continuously increased since the industrial, military and communication activities strongly contribute to the electromagnetic stress of living bodies. In the next the authors present some of the main results obtained regarding the microwave exposure of various types of biological material: bacteria, fungi, young plant seedlings, dry seeds, animal tissues. The electromagnetic exposure was carried out in open space in well controlled environmental conditions by using 10.75 GHz/1 m W cm{sup -2} microwaves. Biochemical assays and cytogenetic tests have been carried out to reveal the changes induced post irradiation. The response of some pathogen bacteria, have been emphasized by means of turbidimetric measurements - the stimulatory effect being noticed at the level of the microbial population density (the stimulation of the human body microbial flora seems to be one of the side ...
2006-07-01
International Nuclear Information System (INIS)
Olfactory tract has been demonstrated to be an important portal for inhaled solid nanoparticle transportation into the central nervous system (CNS). We have previously demonstrated that intranasally instilled Fe_2O_3 nanoparticles could transport into the CNS via olfactory pathway. In this study, we investigated the neurotoxicity and size effect of repeatedly low-dose (130 #mu#g) intranasal exposure of nano- and submicron-sized Fe_2O_3 particles (21 nm and 280 nm) to mice. The biomarkers of oxidative stress, activity of nitric oxide synthases and release of monoamine neurotransmitter in the brain were studied. Our results showed that significant oxidative stress was induced by the two sizes of Fe_2O_3 particles. The activities of GSH-Px, Cu,Zn-SOD, and cNOS significantly elevated and the total GSH and GSH/GSSG ratio significantly decreased in the olfactory bulb and hippocampus after the nano- and submicron-sized Fe_2O_3 particle treatment (p < 0.05). The ...
2009-01-01
International Nuclear Information System (INIS)
A series of measurements of O_3 yield in nuclear induced O_2 and O_2-SF_6 discharges created by bombardment with energetic particles from the "1"0B(n,#alpha#)"7Li reaction are reported. Continuous irradiation at dose ratios of 10"1"5-10"1"7 eV.cm"-"3.s"-"1 and pulsed irradiation (approx.10 ms FWHM) at a peak dose rate of approx.10"2"0 eV.cm"-"3.s"-"1 were conducted. At the lower dose rates, SF_6 addition generally increased the ozone yield, which at the high dose rates, SF_6 addition decreased the observed ozone concentration. A numerical model was developed and applied to experimental conditions. The steady-state ozone concentration was found to be limited by the reaction O_3"- + O_3 #-># 2O_2 + O_2"-. A simplified analytical model of steady-state conditions was used to predict model sensitivity to various parameters. In addition to dose rate effects, pressure and temperature effect on ozone production were discussed. The present study was ...
Energy Technology Data Exchange (ETDEWEB)
Most households in low and middle income countries, including in India, use solid fuels (coal/coke/lignite, firewood, dung, and crop residue) for cooking and heating. Such fuels increase child mortality, chiefly from acute respiratory infection. There are, however, few direct estimates of the impact of solid fuel on child mortality in India. Methods: We compared household solid fuel use in 1998 between 6790 child deaths, from all causes, in the previous year and 609 601 living children living in 1.1 million nationally-representative homes in India. Analyses were stratified by child's gender, age (neonatal, post-neonatal, 1-4 years) and colder versus warmer states. We also examined the association of solid fuel to non-fatal pneumonias. Solid fuel use was very common (87% in households with child deaths and 77% in households with living children). After adjustment for demographic factors and living conditions, solid-fuel use significantly ...
2010-08-17
The risk of ano-genital malignancies in dialysis and transplant patients.
The incidence of anogenital malignancies is greatly increased in patients who have received a renal transplant, but this has not been well studied in patients receiving maintenance dialysis. Our aim was to assess the incidence of these malignancies in patients on dialysis and compare these to transplanted patients. The age standardized incidence ratio (SIR) for anogenital malignancies was calculated by comparing the observed number of malignancies to the expected number. The expected number was calculated by multiplying the age specific incidence rates for each malignancy by the person years at risk in 5-year age cohorts. Of 15,820 patients in the Australia and New Zealand data base, 8,215 had received a renal transplant. A total of 39,750 person years at risk were contributed by patients who had received a renal transplant, while 29,276 person years at risk were contributed by dialysis patients who had not received a renal transplant. For ...
1994-02-01
Most of the general population is exposed to carbaryl and other contemporary-use insecticides at low levels. Studies of laboratory animals, in addition to limited human data, show an association between carbaryl exposure and decreased semen quality. In the present study we explored whether environmental exposures to 1-naphthol (1N), a metabolite of carbaryl and naphthalene, and 3,5,6-trichloro-2-pyridinol (TCPY), a metabolite of chlorpyrifos and chlorpyrifos-methyl, are associated with decreased semen quality in humans. Subjects (n=272) were recruited through a Massachusetts infertility clinic. Individual exposures were measured as spot urinary concentrations of 1N and TCPY adjusted using specific gravity. Semen quality was assessed as sperm concentration, percent motile sperm, and percent sperm with normal morphology, along with sperm motion parameters (straight-line velocity, curvilinear velocity, and linearity). Median TCPY and 1N concentrations were 3.22 and 3.19microg/L, ...
2004-12-01
Energy Technology Data Exchange (ETDEWEB)
Using discrete air sampling, values of {delta}{sup 13}C and {delta}{sup 18}O in atmospheric CO{sub 2}, as well as its concentration, were measured in a forest in the central part of the main island of Japan during the period from June 1994 to June 1996 to examine the biospheric contribution to their temporal variations. {delta}{sup 13}C shows a prominent diurnal variation with high values in the daytime and low values in the nighttime, especially during the warm season. {delta}{sup 13}C also vary seasonally, showing a maximum in summer and a minimum in spring. The diurnal and seasonal variations of {delta}{sup 13}C are opposite in phase with those of the CO{sub 2} concentration. The rate of change in {delta}{sup 13}C with respect to the CO{sub 2} concentration is found to be approximately -0.005 per mille/ppmv. This suggests that the diurnal and seasonal variations of the CO{sub 2} concentration are produced primarily by diurnally- and seasonally-dependent photosynthetic-respiratory ...
1997-09-01
Energy Technology Data Exchange (ETDEWEB)
Radioisotopes of Pb(II) have been of some interest in radioimmunotherapy and radioimmunoimaging (RII). However, the absence of a kinetically stable bifunctional chelating agent for Pb(II) has hampered its use for these applications. {sup 203}Pb (T{sub 1/2}=52.02 h) has application potential in RII, with a {gamma}-emission that is ideal for single photon emission computerized tomography, whereas {sup 212}Pb (T{sub 1/2}=10 h) is a source of highly cytotoxic {alpha}-particles via its decay to its {sup 212}Bi (T{sub 1/2}=60 min) daughter. The synthesis of the novel bifunctional chelating agent 2-(4-isothiocyanotobenzyl)-1,4,7,10-tetraaza-1,4,7,10-tetra-(2-carbamoyl methyl)-cyclododecane (4-NCS-Bz-TCMC) is reported herein. The Pb[TCMC]{sup 2+} complex was less labile to metal ion release than Pb[DOTA]{sup 2-} at pH 3.5 and below in isotopic exchange experiments. In addition to increased stability to Pb{sup 2+} ion release at low pH, the bifunctional TCMC ligand was ...
2000-01-01
International Nuclear Information System (INIS)
Radioisotopes of Pb(II) have been of some interest in radioimmunotherapy and radioimmunoimaging (RII). However, the absence of a kinetically stable bifunctional chelating agent for Pb(II) has hampered its use for these applications. "2"0"3Pb (T_1_/_2=52.02 h) has application potential in RII, with a #gamma#-emission that is ideal for single photon emission computerized tomography, whereas "2"1"2Pb (T_1_/_2=10 h) is a source of highly cytotoxic #alpha#-particles via its decay to its "2"1"2Bi (T_1_/_2=60 min) daughter. The synthesis of the novel bifunctional chelating agent 2-(4-isothiocyanotobenzyl)-1,4,7,10-tetraaza-1,4,7,10-tetra-(2-carbamoyl methyl)-cyclododecane (4-NCS-Bz-TCMC) is reported herein. The Pb[TCMC]"2"+ complex was less labile to metal ion release than Pb[DOTA]"2"- at pH 3.5 and below in isotopic exchange experiments. In addition to increased stability to Pb"2"+ ion release at low pH, the bifunctional TCMC ligand was found to have many other ...
2000-01-01
International Nuclear Information System (INIS)
Full - grown pupae of the cotton leaf worm Spodoptera littorals (Boisd.) were gamma - irradiated with low doses of 25,50,75, or 100 Gy for male line and with 50 or 100 Gy for female line . The effects on reproduction, development and sex ratio were the biological aspects studied among P1,F1,F2 and F 3 generations . Also, the effects of dose accumulation applied grown male pupae through two or three filial generations and the retarded influence on their F1,F2,and F 3 progeny were examined. In another trial the histological examinations for ovaries and testes of irradiated parents and for their generation were made . The F1 males were more sterile than irradiated parental males while F1 females were more fertile than their irradiated parental females. Irradiation of P1 males did not clearly affect neither the percentage of mated females nor the average number of spermatophores per mated female among the individuals of P1,F1,F2 and F 3 generations. Irradiation of P1 ...
Sound transmission loss of composite sandwich panels
Light composite sandwich panels are increasingly used in automobiles, ships and aircraft, because of the advantages they offer of high strength-to-weight ratios. However, the acoustical properties of these light and stiff structures can be less desirable than those of equivalent metal panels. These undesirable properties can lead to high interior noise levels. A number of researchers have studied the acoustical properties of honeycomb and foam sandwich panels. Not much work, however, has been carried out on foam-filled honeycomb sandwich panels. In this dissertation, governing equations for the forced vibration of asymmetric sandwich panels are developed. An analytical expression for modal densities of symmetric sandwich panels is derived from a sixth-order governing equation. A boundary element analysis model for the sound transmission loss of symmetric sandwich panels is proposed. Measurements of the modal density, total loss factor, ...
2009-01-01
Soil chemistry and nutrition of North American spruce-fir stands: Evidence of recent change
International Nuclear Information System (INIS)
One set of hypotheses offered to explain the decline of red spruce (Picea rubens Sarg.) in eastern North America focuses on the effect of acidic deposition on soil chemistry changes that may affect nutrient availability and root function. Long-term soils data suggests that soil acidification has occurred in some spruce stands over the past 50 yr, with plant uptake and cation leaching both contributing to the loss of cations. Studies of tree ring chemistry also have indicated changes in Ca/Al and Mg/Al ratios in red spruce wood, suggesting increases in the ionic strength of soil solution. Irrigation studies using strong acid inputs have demonstrated accelerated displacement of base cations from upper horizons. Spruce-fir (Abies spp.) nutrient budgets indicate that current net Ca and Mg leaching loss rates are of the same order of magnitude as losses to whole tree harvest removals, spread out over a 50-yr rotation. For most cations, red spruce ...
International Nuclear Information System (INIS)
Single-crystalline nanostructures often exhibit gradients of surface (and/or interface) curvature that emerge from fabrication and growth processes or from thermal fluctuations. Thus, the system-inherent capillary force can initiate morphological transformations during further processing steps or during operation at elevated temperature. Therefore and because of the ongoing miniaturization of functional structures which causes a general rise in surface-to-volume ratios, solid-state capillary phenomena will become increasingly important: On the one hand diffusion-mediated capillary processes can be of practical use in view of non-conventional nanostructure fabrication methods based on self-organization mechanisms, on the other hand they can destroy the integrity of nanostructures which can go along with the failure of functionality. Additionally, capillarity-induced shape transformations are effected and can thereby be controlled by applied ...
2009-05-12
Energy Technology Data Exchange (ETDEWEB)
A number of high voltage cathode materials are now being considered for their ability to increase the energy density of lithium-ion batteries. In this study, a lithium-nickel composite alloy (LiNiVO{sub 4}) was synthesized using a rheological phase reduction method that incorporated mixtures of LiOH-H{sub 2}O, Ni(CH{sub 3}COO){sub 2}, 4H{sub 2}O, NH{sub 4}VO{sub 3} and C{sub 2}H{sub 2}O{sub 4}-2H{sub 2}O. The rheological phase method was used to prepare the compounds from a solid-liquid rheological mixture. Solid reactants were first mixed in a proper molar ratio, and water or solvents were added to the solid-liquid rheological body. X-ray powder diffraction (XRD) and Fourier Transform (FT) analyses were conducted to characterize the powders. Scanning electron microscopy (SEM) was used to characterize the morphological features and particle sizes of the powders. Results of the analyses indicated that the single-phase LiNiVO{sub 4} composite is ...
2008-08-15
DEFF Research Database (Denmark)
BACKGROUND: The aetiologies of glioma and meningioma tumors are largely unknown. Although reproductive hormones are thought to influence the risk of these tumors, epidemiologic data are not supportive of this hypothesis; however, few cohort studies have published on this topic. We examined the relation between reproductive factors and risk of glioma and meningioma among women in the European Prospective Investigation into Cancer and Nutrition (EPIC).METHODS: After a mean of 8.4 years of follow-up, 193 glioma and 194 meningioma were identified among 276,212 women. Information on reproductive factors and hormone use was collected at baseline. Cox proportional hazard regression was used to determine hazard ratios (HR) and 95% confidence intervals (CI). RESULTS: No associations were observed between glioma or meningioma risk and reproductive factors, including age at menarche, parity, age at first birth, menopausal status, and age at menopause. A higher risk of ...
2010-01-01
Radioiodide uptake in brain, CSF, thyroid, and salivary glands of audiogenic seizure mice
Energy Technology Data Exchange (ETDEWEB)
DBA/2J (DBA) mice are susceptible to audiogenic seizures (ASs) in an age-dependent manner. Anion transport as measured by radioiodide uptake was determined in thyroid gland, salivary gland, skeletal muscle, cerebral cortex, cerebellum, brainstem, and CSF from these mice at various ages. Anion transport was also determined in C57BL/6J(C57) mice, an AS-resistant strain. In thyroid, DBA mice had an enhanced ability to concentrate iodide at 21 days of age when they have maximal AS susceptibility, as compared with the same-aged C57 mice. This difference in thyroid function was less marked at 40 days of age, when DBA mice are less AS susceptible, and was absent at 110 days of age, when DBA mice are AS resistant. In brain, differences in iodide uptake were also noted between these two strains of mice at 21 days of age. DBA mice had an increased concentration of iodide in CSF, an indication that they have a defect in the transport of iodide out of the CSF across the ...
1984-08-01
Wood Plastic Composites (WPCs) have experienced a healthy growth during the last decade. However, improvement in properties is necessary to increase their utility for structural applications. The toughness of WPCs can be improved by creating a fine cellular structure while reducing the density. Extrusion processing is one of the most economical methods for profile formation. For our study, rectangular profiles were extruded using a twin-screw extrusion system with different grades of HDPE and with varying wood fibre and lubricant contents together with maleated polyethylene (MAPE) coupling agent to investigate their effects on WPC processing and mechanical properties. Work has been done to redesign the extrusion system setup to achieve smoother and stronger profiles. A guiding shaper, submerged in the water, has been designed to guide the material directly through water immediately after exiting the die; instead of passing it through a water cooled vacuum ...
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
To predict the response of blood lead to airborne and dietary lead requires knowledge of the rate of uptake of lead into the body from lung and gut, its subsequent partitioning between compartments, the stay time in those compartments, and its redistribution or excretion. Tracer studies with volunteers have shown no differences in systemic distribution of inorganic lead between tissues whether it is taken by inhalation, ingestion or injection. Lead is rapidly transferred from plasma to red cells, and there is slower movement thence into liver and other soft tissues, to bone, and to excreta. Work at Harwell and elsewhere with /sup 203/Pb has shown that the initial rapid distribution leaves rather over half the assimilated lead attached to red cells. The result is remarkably consistent, and applies also to dogs and baboons. The renal clearance (Vu) (ratio of U to CB, or daily urinary output expressed as mass of blood having the same lead content), and also the ...
1985-04-22
Performance of spark ignited gas engine and dual fuel engine, and their application
Energy Technology Data Exchange (ETDEWEB)
This paper describes a practical knowledge on gas engine performance and combustion characteristics which are required by experimental studies for two types of developed gas burning engines, i. e. a spark ignited gas engine and a dual fuel engine, and also introduces their practical use and application. As for dual fuel engine performance, a manifold air pressure of about 27% was decreased, a scavenging ratio of 23% reduced and an exhaust temperature at the turbine inlet on 14% was increased at the gas engine operation under the mean effective cylinder pressure of 1.22 MPa in comparison with the diesel operation. Furthemore, empirical data on the effect of excess air ration on the engine performance and combustion characteristics, a risk of knocking during changing over on the dual fuel engine operation, and the rated output in case of using alternate fuel gas were reported. Two spark ignited gas engines with a rated output of 250 PS each using ...
1988-12-01
Patterns of radionuclide concentrations in life-cycle of birds
Energy Technology Data Exchange (ETDEWEB)
Breeding populations of Great Tit Parus major and Pied Flycatcher Ficedida hypoleuca was studied to determine radionuclide ({sup 137}Cs, {sup 90}Sr) concentrations in bodies and foods (contents of gastrointestinal tracts) at different stages of the life-cycle and radiation effects upon the populations. The study was carried out in 1989--1992 near Chernobyl (in two areas with differed contamination levels: 90 Ci/km{sup 2}, 5 Ci/km{sup 2}) and East-Ural radioactive trace (Russia) (1,500 Ci/km{sup 2}, 2 Ci/km{sup 2}). Concentrations of {sup 90}Sr in egg shells of Great Tit collected near Chernobyl were 65 times higher in the more radioactive area than in the less contaminated area and varied from 56.6 to 79.7 Bq/g. Concentration of {sup 90}Sr in the contents of gastrointestinal tracts were from 0 to 10.8 Bq/g. Concentrations of radionuclides in the food increased in the sequence ``nestlings < fledglings < adults``. However, the accumulation declined from ...
1995-12-31
Optimal design of perforating completion for gas well
Energy Technology Data Exchange (ETDEWEB)
The productivity characteristics of perforated gas well are investigated for the first time under real conditions considering drilling damage, perforation compacted zone and anisotropy in this paper. A non-linear finite element model for non-Darcy flow in perforated gas reservoir is built to consider the effects of twelve factors on productivity ratio (PR) of perforated gas well. The nomographs for two cases are presented in this paper. Compared with previous works, the following results are found: (1) the effects of drilling damage and perforation diameter on PR of gas well are more remarkable than that in oil well; (2) any perforation phase may be the best or the worst as to perforating gas well, which depends on anisotropy, drawdown and that whether or not perforations are beyond drilling damage zone; (3) the increase in perforation length hardly improve PR of gas well when perforations have been beyond drilling damage zone. The new method ...
1995-10-01
International Nuclear Information System (INIS)
A new dirhenium(I) complex fac-[{Re(CO)3(4,7-dinonadecyl-1,10-phenanthro -line)}2 (4,4'-bipyridyl)] (trifluoromethanesulfonate)2 (denoted as D-Re(I) ) is assembled in MCM-41 and SBA-15 type mesoporous silica support. The emission peaks of D-Re(I) in D-Re(I)/MCM-41 and D-Re(I)/SBA-15 are observed at 522 and 517 nm, respectively. Their long excited lifetimes, which are of the order of microseconds, indicate the presence of phosphorescence emission arising from the metal to ligand charge-transfer (MLCT) transition. The luminescence intensities of D-Re(I)/MCM-41 and D-Re(I)/SBA-15 decrease remarkably with increase in the oxygen concentration, meaning that they can be used as optical oxygen sensing materials based on luminescence quenching. The ratios I0/I100 of D-Re(I)/MCM-41 and D-Re(I)/SBA-15 are estimated to be 5.6 and 20.1, respectively. The obtained Stern-Volmer oxygen quenching plots of the mesoporous sensing materials could be fitted well to ...
2011-04-01
On the cells of origin of radiogenic thyroid cancer: New studies based on an old idea
Energy Technology Data Exchange (ETDEWEB)
We have presented evidence that the functional thyroid follicles (follicular units, FU) which are formed in grafts of monodispersed rat thyroid cells, and hence the thyroid tumors which later develop in such grafts, are clonal in origin. Recent studies have been designed to investigate: whether cell number-dependent inhibition of promotion-progression is mediated by remote hormonal feed-back, local cell-cell interactions, or both; the cell population kinetics of the clonogen subpopulation during goitrogenesis and goiter involution; and the effect of prolonged exposure to high levels of TSH (thyrotropin) on the capacity of the clonogens to give rise to functional FU. The results indicate that local cell-cell interactions play an important role in the cell number-dependent suppression of neoplastic promotion-progression. They also show that if sufficient thyroid cells are grafted, the thyroid-pituitary axis can be reestablished in thyroidectomized rats fed normal diets. In such animals ...
1990-01-01
Energy Technology Data Exchange (ETDEWEB)
Blade fatigue life is an important element in determining the economic viability of the Vertical-Axis Wind Turbine (VAWT). A principal source of blade fatigue is thought to be the stochastic (i.e., random) aerodynamic loads created by atmospheric turbulence. This report describes the theoretical background of the VAWT Stochastic Aerodynamic Loads (VAWT-SAL) computer code, whose purpose is to numerically simulate these random loads, given the rotor geometry, operating conditions, and assumed turbulence properties. A Double-Multiple-Stream Tube (DMST) analysis is employed to model the rotor's aerodynamic response. The analysis includes the effects of Reynolds number variations, different airfoil sections and chord lengths along the blade span, and an empirical model for dynamic stall effects. The mean ambient wind is assumed to have a shear profile which is described by either a power law or a logarithmic variation with height above ground. Superimposed on this is a full 3-D ...
1991-09-01
Lubricating composition for processing of flushing fluids
Energy Technology Data Exchange (ETDEWEB)
Proposed is a lubricating composition for processing flushing fluids, which contains synthetic fatty acids of the fraction carbon 11-20, oxidized petrolatum, mineral oil, and additives. In order to increase the antiwear, anticorrosion, and antiscratching properties of the composition under conditions of polymineral corrosion with simultaneous decrease in the water loss of the flushing fluids as additives the composition contains stearic acid, polyoxyethylated methyl phenol, naptha soap, 1,5-dibenzoylnapthaline-4', 4''-dicarboxylic acid, calcined soda, secondary nonsaponifiables, obtained in the production of synthetic fatty acids by oxidation of paraffin, and polyfunctional oxygen-bearing compounds, obtained by oxidation of secondary nonsaponifiables by atmospheric oxygen, with the following ratio of components, wt%: 17.2-19.2% synthetic fatty acids of the carbon 17-20 fraction, 5.2-5.8% oxidized petrolatum, 3.5-3.7% ...
1981-03-15
Layered PrBaCo_2O_5_+_#delta# perovskite as a cathode for proton-conducting solid oxide fuel cells
International Nuclear Information System (INIS)
The layered PrBaCo_2O_5_+_#delta# (PBCO) perovskite oxides were synthesized by modified Pechini method and investigated as a cathode material for solid oxide fuel cells (SOFCs) based on a stable and easily sintered perovskite oxide BaCe_0_._5Zr_0_._3Y_0_._1_6Zn_0_._0_4O_3_-_#delta# (BCZYZ) as electrolyte. The fabricated single cell of NiO-BCZYZ/BCZYZ (#approx#20 #mu#m)/PBCO was operated from 550 to 700 "oC with humidified hydrogen (#approx#5% H_2O) as fuel and the static air as oxidant. The BCZYZ perovskite electrolyte was completely dense after sintered at 1250 "oC for 5 h, lower than that without zinc dopant about 150 "oC. A high open-circuit potential of 1.007 V, a peak power density of 361 mW cm"-"2, and a low polarization resistance of the electrodes of 0.12 #OMEGA# cm"2 was achieved at 700 "oC. The ratio of polarization resistance to total cell resistance decreased with the increase of operating temperature, from 54.2% at 550 "oC to 17.9% ...
2010-04-02
International Nuclear Information System (INIS)
The layered GdBa_0_._5Sr_0_._5Co_2O_5_+_#delta# (GBSC) perovskite oxides are synthesized by modified Pechini method and investigated as a novel cathode material for solid oxide fuel cells (SOFCs) based on a stable perovskite oxide BaCe_0_._5Zr_0_._3Y_0_._1_6Zn_0_._0_4O_3_-_#delta# (BCZYZ) as electrolyte. The fabricated single cells of NiO-BCZYZ/BCZYZ (#approx#20 #mu#m)/GBSC (#approx#20 #mu#m) were operated from 550 to 700 "oC with humidified hydrogen (#approx#5% H_2O) as fuel. The BCZYZ perovskite electrolyte was completely dense after sintered at 1250 "oC for 5 h, lower than that without zinc dopant about 150 "oC. An open circuit voltage of 1.009 V and a maximal power density of 0.35 W cm"-"2 were achieved at 700 "oC. The interfacial polarization resistance was as low as 1.46, 0.45, 0.25 and 0.15 #OMEGA# cm"2 at 550, 600, 650 and 700 "oC, respectively. The ratio of polarization resistance to total cell resistance decreased with the increase in ...
2010-04-30
Energy Technology Data Exchange (ETDEWEB)
The objective of this project is to develop a pellet formulation which is capable of achieving low sulfur partial pressures and a high capacity for sulfur, loaded from a hot fuel gas and which is readily regenerable. Furthermore the pellet must be strong for potential use in a fluidized bed and regenerable over many cycles of loading and regeneration. Regeneration should be in air or oxygen-depleted air to produce a high-concentration sulfur dioxide. Fixed-bed tests were conducted with several formulations of manganese sesquioxide and titania, and alumina They were subject to a simplified fuel gas of the oxygen-blown Shell type spiked with a 30,000ppmv concentration of H{sub 2}S. Pellet crush strengths for 4 and 2mm diameter pellets was typically 12 lbs per pellet and 4 lbs per pellet, respectively. For the most favorable of the formulations tested and under the criteria of break-through at less than 100ppmv H2S and loading temperatures of 500{degrees}C and an empty-bed space velocity ...
1996-06-12
Inherited sterility progeny gamma irradiated male Spiny Bollworm Earias Insulana Boisd
International Nuclear Information System (INIS)
The present work studies the fecundity, egg batching and mating of normal females of Earias Insulana Boisd. crossed with males irradiated as 24 h adult moths with two doses (80 and 100 Gy.) of gamma radiation. The male progeny were out bred or inbred with untreated individuals for two successive generations F_1and F_2 and their progeny was observed for any inherited deleterious effects on reproduction. The female fecundity and egg hatch were significantly reduced among P1,F1 and F2 generations by increasing the dosages applied to P_1 males as compared with the untreated control. The percentage of mating of P_1 females was significantly reduced at the two doses as compared to the untreated control. The average number of spermatophores per mated female was reduced among P_1,F_1 and F_2 generations when parental males were irradiated with 100 Gy. The larval and pupal mortality a,o mg F_1, F_2 and F_3 generations was high and dose dependent. The average developmental ...
2003-01-01
Energy Technology Data Exchange (ETDEWEB)
A new multicusp H{sup -} ion source using a Localized Virtual magnetic filter of type I [Ref.6] in the plasma electrode is investigated. A multipole (MP) arrangement with a spacing of 10 mm of the magnet bars holds an extraction hole, optimizing the efficient production of high H{sup -} current, and at the same time only a small electron component was co-extracted with the H{sup -} ions. The local filter arrangement separates the beam electrons at a low energy. It is shown that the co-extracted total electron current is determined principally by the integrated magnetic field flux (Gcm) of the local filter with an extraction system at a constant extraction voltage. When the value of the Gcm is increased, the total electron component is reduced, while the H{sup -} electrical efficiency had a broad maximum around the optimized value of the Gcm. A thicker plasma electrode should be necessary for sufficient reduction of electron current. In pure hydrogen operation, the ...
1999-12-01
Energy Technology Data Exchange (ETDEWEB)
Magnesium-based alloys are among the promising materials for hydrogen storage and fuel cell applications due to their high hydrogen content. In the present work, we investigated the hydrogen release/uptake properties of the Mg-Ti-H system. Samples were prepared from the mixtures of MgH{sub 2} and TiH{sub 2} in molar ratios of 7:1 and 4:1 using a high-energy-high-pressure (HEHP) mechanical ball-milling method under 13.8 MPa hydrogen pressure. Thermogravimetric analysis (TGA) showed that a relatively large amount of hydrogen (5.91 and 4.82 wt.%, respectively, for the above two samples) was released between 126 and 313 C while temperature was increased at a heating rate of 5 C min{sup -1} under an argon flow. The onset dehydrogenation temperature of these mixtures, which is 126 C, is much lower than that of MgH{sub 2} alone, which is 381 C. The activation energy of dehydrogenation was 71 kJ mol{sup -1}, which is much smaller than that of ...
2008-05-15
Hydrocarbon generation potential of some Hungarian low-rank coals
Energy Technology Data Exchange (ETDEWEB)
Several Hungarian lignite and brown coal samples were studied by coal petrographical, palynological and organic geochemical methods. Three of these were chosen for a series of pyrolysis experiments. Thermal treatment was carried out on two H-rich Eocene brown coals (kerogen: Type II) and a H-poor Miocene lignite (kerogen Type III) between 200 and 500{degree}C. The products of experiments (insoluble residue, chloroform soluble bitumen and volatilized bitumen) were investigated. During diagenesis the hydrocarbon potential of lignite decreased by 75% and that of the coals diminished approximately 50%. The zone of the catagenesis was reached at 350{degree}C by lignite and at 375{degree}C by coals. The coal-2 is somewhat more resistant to thermal degradation than coal-1. Various hydrocarbon classes (alkanes, alkenes, phyllocladanes, isoprenoids) were measured in non-aromatic hydrocarbon fractions. Volatile bitumens contained much more unsaturated hydrocarbons than the bitumens extracted ...
1990-01-01
High ion density plasma etching of InGaP, AlInP, and AlGaP in CH{sub 4}/H{sub 2}/Ar
High microwave power (1,000 W) electron cyclotron resonance CH{sub 4}/H{sub 2}/Ar discharges produce etch rates for In{sub 0.5}Ga{sub 0.5}P, Al{sub 0.5}In{sub 0.5}P{sub 0.5}, and Al{sub 0.5}Ga{sub 0.5}P of {approximately} 2,000 {angstrom}/min at moderate RF power levels (150 W) and low pressure (1.5 mTorr). This is approximately a factor of five faster than for conventional reactive ion etching conditions where much higher ion energies are necessary. The etched surfaces are smooth over a wide range of CH{sub 4}-to-H{sub 2} ratios and microwave powers. AlInP is more resistant to preferential loss of P from the near-surface during etching than is InGaP. While the etching is ion-driven, pure Ar discharges produce rough surfaces and the CH{sub 4}/H{sub 2} is necessary in the achievement of acceptable morphologies. The InGaAlP/GaAs heterostructure is being increasingly utilized in diode lasers, light emitting diodes, field-effect transistors, and ...
1996-03-01
International Nuclear Information System (INIS)
Influence of alkali elements on formation, composition, solubility and region of stability of complex hafnium sulfates, separated in the HfO"2-H"2SO"4-Me"2SO"4-H"2O (Me-Na, K, Rb, Cs and NH"4 group) systems is studied. In all cases hafnium forms the complex sulfates of three types differing by basicity or ratio HfO"2:SO"3 1:1, 1:1.5, 1:2. Three basic and three medium sulfates are crystallized in the systems with sodium; with rubidium, cesium and ammonium - two basic and two medium sulfates and with potassium - two basic and one medium salts. Anhydrous salts do not form in the investigated systems. Potassium salt approximately 0.3% according to HfO"2 is characterized by minimum solubility from the salts of 2HfOSO"4x(1-3)Me"2SO"4x(4-6)xH"2O while solubility of the same salts with rubidium, cesium and sodium increases from (0.25-1.0); (0.5-1.5) till (1.0-5)% according to HfO"2 correspondingly.
1982-01-01
Evaluation of chitosan/beta-tricalcium phosphate microspheres as a constituent to PMMA cement.
Two methods, a traditional emulsion technique and a high voltage electrostatically modified encapsulation system, were used to fabricate degradable chitosan/beta -tricalcium phosphate (beta-TCP) microspheres. The two distinct kinds of microspheres both exhibited good sphericity and the beta-TCP was trapped well inside the chitosan gel. The microspheres prepared by high voltage electrostatic system exhibited a rougher outer surface and narrower size distribution. These microspheres were then used as an added constituent to commercially available PMMA bone cement. Four modified cement composites that were prepared with different composition ratios of the two kinds of chitosan/beta-TCP microspheres that were made from emulsion technique (C1P1 and C2P1) and from a process by a high voltage electrostatic system (EC1P1 and EC2P1) were compared with the PMMA cement (Pure P). The characteristics of these materials indicate that with the addition of chitosan/beta-TCP ...
2005-06-01
Estimate of the scatter component in SPECT
Energy Technology Data Exchange (ETDEWEB)
Analytical expressions that describe the dependence of slopes and amplitudes of the scatter distribution functions (SDF) on source depth and media density are used to estimate a scatter component in SPECT projection data. Since the ratio of detected scattered to total photons (S/T), SDF amplitude and slope depend strongly on line source length (SL) used to obtain SDFs, we compared estimated scattered components using SDFs, obtained for lengths of 2-21 cm. At 10 cm source depth, S/T changes from 0.19 to 0.36 when SL changes from 2 to 21 cm. Scatter amplitude`s dependence on source depth (d) in water was described by 6.38e{sup -0.186d} for a 2 cm and 16.15e{sup -0.129d} for a 21 cm SL. Slope was described by 0.292d{sup -0.601} for a cm SL and by 0.396d{sup -0.82} for a 21 cm SL. The estimated scatter components are compared with simulated SPECT projection data obtained with Monte Carlo modeling of six hot spheres placed in a cylindrical water filled phantom. The ...
1996-12-31
Enhanced spectral discrimination through the exploitation of interface effects in photon dose data
International Nuclear Information System (INIS)
The convolution/superposition algorithm for computing dose from photon beams in radiation therapy planning requires knowledge of the energy spectrum. The algorithm can compute the dose for a polyenergetic beam as the weighted sum of the individual dose contributions from monoenergetic beams. In this study we exploit interface effects apparent in the dose distributions to discriminate among spectra of high energy photon beams. We have studied the sensitivity of the depth dose distribution to the energy components using a hypothetical beam for various field sizes and depths in water and water-lung-water media. Six theoretical spectra were simulated. We compared depth dose data from these spectra using three quantitative measures which are inherently free of normalization ambiguities: for homogeneous water, the ratio D_2_0/D_1_0 and a logarithmic derivative in the buildup region LD_b_u_i_l_d_-_u_p and for inhomogeneous lung/water, the lung correction factor (CF). It ...
2004-02-01
Electron-ion recombination of neutral iron
Energy Technology Data Exchange (ETDEWEB)
The total and state-specific electron-ion recombination rate coefficients are obtained for FeI. The calculations are carried out using a new ab initio method that incorporates both the radiative and the dielectronic recombination processes in an unified and self-consistent manner. The computations employ the close coupling approximation and the R-matrix method from atomic collision theory. A 52 state close coupling eigenfunction expansion dominated by the states of the ground 3d{sup 6}4s and excited 3d{sup 7}, 3d{sup 6}4p, 3d{sup 5}4s{sup 2}, and 3d{sup 5}4s4p configurations of FeII are used in the present calculations. The important electron correlation and radiation damping effects are included via explicit coupling of autoionization and radiative channels. This is the first detailed atomic calculation for the recombination rates for FeI. The present rates are considerably higher than the radiative recombination rates being used currently in the low-temperature region, T{le}10{sup ...
1997-04-01
Effective thickness of CeO{sub 2} buffer layer for YBCO coated conductor by advanced TFA-MOD process
Energy Technology Data Exchange (ETDEWEB)
YBCO films were fabricated on PLD-CeO{sub 2}/IBAD-Gd{sub 2}Zr{sub 2}O{sub 7}/Hastelloy substrates using the advanced TFA-MOD process. The effective thickness of the CeO{sub 2} buffer layer for obtaining high I{sub c} was investigated in short samples of YBCO films. The CeO{sub 2} buffer layer was epitaxially grown on an IBAD-Gd{sub 2}Zr{sub 2}O{sub 7} template tape with 18 deg. of {delta}{phi} by a reel-to-reel PLD system. The in-plane grain alignment of PLD-CeO{sub 2} buffer layers rapidly improved with the thickness and saturated at a critical thickness of 0.8 {mu}m. The size of CeO{sub 2} grains was about 1 {mu}m at the saturated thickness of {delta}{phi}. YBCO films with the thickness of 1 {mu}m were deposited by the TFA-MOD on the CeO{sub 2} buffer layer with different thickness films. Improvement of the CeO{sub 2} in-plane grain alignment resulted in increase of I{sub c}. The I{sub c} values of 250-290 A were obtained with the CeO{sub 2} layer thicker than ...
2007-10-01
International Nuclear Information System (INIS)
This study was carried out to evaluate the effects of irradiation (gamma irradiation at dose levels of 0.0, 2.5, 5.0, 10.0 or 20.0 kGy, He-Ne and their combination) on nutritive characteristics of Vicia faba L. seeds (Giza 843). Analyses included levels of anti-nutrients (total phenolic compounds, tannins, phytic acid, trypsin inhibitor and vicine), chemical composition (sugars, crude proteins, fat, dry matter and ash) and fatty acids profile. All treatments caused significant (P<0.05) decreases in the antinutrational factors under investigation. The reduction in the content of tannins and phenolic compounds were more pronounced with He-Ne alone or He-Ne in combination with gamma irradiation. At dose levels 10.0 and 20.0 kGy without or with combination of He-Ne were more efficiency in the reduction of phytic acid content by 24.3, 32.8, 34.5 and 45.5 %, respectively. Also, for trypsin inhibitor activity, the maximum inhibition was observed with the treatment of 20 kGy + He-Ne (36.7 ...
Dynamic-stiffness matrix of embedded and pile foundations by indirect boundary-element method
Energy Technology Data Exchange (ETDEWEB)
The boundary-integral equation method is well suited for the calculation of the dynamic-stiffness matrix of foundations embedded in a layered visco-elastic halfspace (or a transmitting boundary of arbitrary shape), which represents an unbounded domain. It also allows pile groups to be analyzed, taking pile-soil-pile interaction into account. The discretization of this boundary-element method is restricted to the structure-soil interface. All trial functions satisfy exactly the field equations and the radiation condition at infinity. In the indirect boundary-element method distributed source loads of initially unknown intensities act on a source line located in the excavated part of the soil and are determined such that the prescribed boundary conditions on the structure-soil interface are satisfied in an average sense. In the two-dimensional case the variables are expanded in a Fourier integral in the wave number domain, while in three dimensions, Fourier series in the circumferential ...
1984-08-01
Disability and health-related rehabilitation in international disaster relief
BackgroundNatural disasters result in significant numbers of disabling impairments. Paradoxically, however, the traditional health system response to natural disasters largely neglects health-related rehabilitation as a strategic intervention.ObjectivesTo examine the role of health-related rehabilitation in natural disaster relief along three lines of inquiry: (1) epidemiology of injury and disability, (2) impact on health and rehabilitation systems, and (3) the assessment and measurement of disability.DesignQualitative literature review and secondary data analysis.ResultsAbsolute numbers of injuries as well as injury to death ratios in natural disasters have increased significantly over the last 40 years. Major impairments requiring health-related rehabilitation include amputations, traumatic brain injuries, spinal cord injuries (SCI), and long bone fractures. Studies show that persons with pre-existing disabilities are more likely to die in a ...
2011-08-16
Direct liquefaction Proof-of-Concept facility. Final technical progress report
Energy Technology Data Exchange (ETDEWEB)
This report presents the results of work which included extensive modifications to HRI`s existing 3 ton per day Process Development Unit (PDU) and completion of the first PDU run. The 58-day Run 1 demonstrated scale-up of the Catalytic Two-Stage Liquefaction (CTSL Process) on Illinois No. 6 coal to produce distillate liquid products at a rate of up to 5 barrels per to of moisture-ash-free coal. The Kerr McGee Rose-SR unit from Wilsonville was redesigned and installed next to the US Filter installation to allow a comparison of the two solids removal systems. Also included was a new enclosed reactor tower, upgraded computer controls and a data acquisition system, an alternate power supply, a newly refurbished reactor, an in-line hydrotreater, interstage sampling system, coal handling unit, a new ebullating pump, load cells and improved controls and remodeled preheaters. Distillate liquid yields of 5 barrels/ton of moisture ash free coal were achieved. Coal slurry recycle rates were ...
1995-08-01
Development of a dedicated ethanol ultra-low emission vehicle (ULEV) system design
Energy Technology Data Exchange (ETDEWEB)
The objective of this 3.5 year project is to develop a commercially competitive vehicle powered by ethanol (or ethanol blend) that can meet California`s ultra-low emission vehicle (ULEV) standards and equivalent corporate average fuel economy (CAFE) energy efficiency for a light-duty passenger car application. The definition of commercially competitive is independent of fuel cost, but does include technical requirements for competitive power, performance, refueling times, vehicle range, driveability, fuel handling safety, and overall emissions performance. This report summarizes a system design study completed after six months of effort on this project. The design study resulted in recommendations for ethanol-fuel blends that shall be tested for engine low-temperature cold-start performance and other criteria. The study also describes three changes to the engine, and two other changes to the vehicle to improve low-temperature starting, efficiency, and emissions. The three engine ...
1995-02-01
Energy Technology Data Exchange (ETDEWEB)
Two types of thermal control materials based on polyimide film UPILEX-R are designed. One of thermal control material R/Al is coated with Al on the back surface. The other of thermal control material TCC/R/Al is coated with transparent conductive coating on the font surface and is coated with Al on the balk surface. The solar absorptance is measured spectroscopically with an integrating sphere in the wavelength region of 0.26 - 2.50 {mu}m and the total hemispherical emittance is measured calorimetrically in the temperature range of -100-+100{degree}C for the present thermal control materials. To evaluate the space degradation of optical properties (refractive index, extinction coefficient, absorption coefficient) on UPILEX-R film and solar absorptance on thermal control materials, space environment simulation tests are performed on the ground with independent radiation and combined radiation by UV, electrons, and protons. An onboard simultaneous measurement experiment with TCC/R/Al ...
1996-01-20
Characterization of flame front surfaces in turbulent premixed methane/air combustion
Energy Technology Data Exchange (ETDEWEB)
A detailed experimental investigation of the application of fractal geometry concepts in determining the turbulent burning velocity in the wrinkled flame regime of turbulent premixed combustion was conducted. The fractal dimension and cutoff scales were determined for six different turbulent flames in the wrinkled flame regime, where the turbulence intensity, turbulent length scale, and equivalence ratio were varied. Unlike previous reports, it has proved possible to obtain the fractal dimension and inner and outer cutoffs from individual flame images. From this individual data, the pdf distributions of all three fractal parameters, along with the distribution of the predicted increase in surface area, may be determined. The analysis of over 300 flame images for each flame condition provided a sufficient sample size to accurately define the pdf distributions and their means. However, the predicted S{sub T}/S{sub L}, calculated using fractal ...
1995-06-01
Application of a polycarboxylate ether admixture in RCC dam construction[ACI SP-239
Energy Technology Data Exchange (ETDEWEB)
Chemical admixtures are used in dam construction to improve plasticity of the dry materials mixture over time. Roller compacted concrete (RCC) has been used on many dam projects in China. However, the use of RCC has frequently resulted in water reduction problems. This paper provided details of an admixture based on polycarboxylate ether (PCE) which was developed to improve the quality of RCC constructions at the JinHong dam in China. Use of the polymer at the JinHong dam resulted in a vibration sensitive concrete that was sustained over time. Under identical mix-design and compaction conditions in the laboratory, specific gravity of the RCC was increased from 2417 kg/m{sup 3} to 2463 kg/m{sup 3}. The high specific gravity of the material resulted in satisfactory strength data from the dam project. The key-ratio of the splitting tensile strength versus compressive strength was higher than 8 per cent in all cases. A key advantage of the tailored ...
2006-07-01
Aerodynamic effects of flexibility in flapping wings.
Recent work on the aerodynamics of flapping flight reveals fundamental differences in the mechanisms of aerodynamic force generation between fixed and flapping wings. When fixed wings translate at high angles of attack, they periodically generate and shed leading and trailing edge vortices as reflected in their fluctuating aerodynamic force traces and associated flow visualization. In contrast, wings flapping at high angles of attack generate stable leading edge vorticity, which persists throughout the duration of the stroke and enhances mean aerodynamic forces. Here, we show that aerodynamic forces can be controlled by altering the trailing edge flexibility of a flapping wing. We used a dynamically scaled mechanical model of flapping flight (Re approximately 2000) to measure the aerodynamic forces on flapping wings of variable flexural stiffness (EI). For low to medium angles of attack, as flexibility of the wing increases, its ability to generate aerodynamic ...
2009-08-19
Advantages of magnification in digital phase-contrast mammography using a practical X-ray tube
Energy Technology Data Exchange (ETDEWEB)
Phase-contrast imaging with a practical cone-beam X-ray tube has been realized for clinical use in digital mammography using computed radiography (CR). To perform phase-contrast imaging, the X-ray detector must be distanced from an object so that the phase-contrast image achieves magnification; in a mammography unit dedicated to phase-contrast imaging, the magnification ratio is 1.75. When using an X-ray tube with a 0.1-mm focal spot, it appears that the penumbra in magnification blurs both projected images and the phase contrast, which generates an edge effect. However, where the sampling pitch of the CR plate is 43.75 {mu}m, the blur stretches the width of the phase contrast so that unit pixels in the detector can capture it. Note that the width of an ideal phase contrast using an X-ray point source results in a phase contrast too narrow for detection with CR. In addition to phase contrast improving image quality, a re-scaling effect ...
2008-12-15
Energy Technology Data Exchange (ETDEWEB)
Various methods for storing hydrogen have been examined in an effort to find ways to store hydrogen in increasingly smaller volumes with decreasing weight of the whole hydrogen storage system. Metal hydrides, in which hydrogen is chemically bound to a metal atom, are considered to be very promising candidates for hydrogen storage because they have high gravimetric and volumetric storage capacities. This study investigated the effect of different magnesium (Mg) and aluminium (Al) ratios on the absorption and desorption properties of thin films. Neutron reflectometry (NR) was used in this study to better understand the absorption and desorption properties of commercially promising hydrogen storage materials. The large negative scattering length of hydrogen atoms changes the reflectivity curve substantially, so that NR can determine the total amount of stored hydrogen as well as the hydrogen distribution along the film normal, with nanometer ...
2010-10-15
A Clinical Study on the Value of a Scoring System of the Scanning Images in Liver Cirrhosis
International Nuclear Information System (INIS)
Although the radioisotope liver scan has primarily been of use in the detection of the intra-hepatic space occupying lesions, there has been an increasing awareness of its use in evaluation of liver function. In this study, the degree of hepatomegaly, changes in shape and mottling radiodensity on each lobe and splenic visualization in the liver scans done with colloidal radiogold were numerically expressed as scores under the arbitrary standard in 210 patients with liver cirrhosis. The clinical value of this scoring system was studied with special regards to the correlation between the radiogold hepatic uptake half time and conventional liver function tests. Following were the results; 1) The normal scan appeared in 6.7% of 210 patients with liver cirrhosis. 2) The colloidal radiogold hepatic uptake half time was abnormally and progressively prolonged in parallel to severity of hepatocellular dysfunction. The mean hepatic uptake half time in cirrhosis showing ...
1970-09-01
Potential Increases in Mortality due to Global Warming
... predicting potential increases in human mortality due to global warming....
Real-time neutron radiography system performance - Measurements and methods
Energy Technology Data Exchange (ETDEWEB)
The University of Virginia's real-time neutron radiography facility was characterized by measurement of the total neutron flux, gold/cadmium ratio, neutron/gamma ratio, and the effective collimar length-to-aperture diameter (L/D) ratio. The real-time neutron imaging system and collimator were further characterized by measuring the modulation transfer function (MTF) of the system. The collimator effectiveness was measured by using the MTF to determine the ''unparallelism'' of the neutron beam. The computer-based image processing system allowed rapid calculation of the MTF and the collimator effectiveness. The results of these measurements, using no collimator and a simple tube collimator, demonstrated the method's ability to determine the effective L/D ratio. The MTF measurement scheme provided a fast, reliable, and reproducible means of monitoring ...
1988-09-01
Real-time neutron radiography system performance - Measurements and methods
International Nuclear Information System (INIS)
The University of Virginia's real-time neutron radiography facility was characterized by measurement of the total neutron flux, gold/cadmium ratio, neutron/gamma ratio, and the effective collimar length-to-aperture diameter (L/D) ratio. The real-time neutron imaging system and collimator were further characterized by measuring the modulation transfer function (MTF) of the system. The collimator effectiveness was measured by using the MTF to determine the ''unparallelism'' of the neutron beam. The computer-based image processing system allowed rapid calculation of the MTF and the collimator effectiveness. The results of these measurements, using no collimator and a simple tube collimator, demonstrated the method's ability to determine the effective L/D ratio. The MTF measurement scheme provided a fast, reliable, and reproducible means of monitoring any changes in the real-time system, including both the ...
1988-01-01
Energy Technology Data Exchange (ETDEWEB)
In this paper, an amount of confining reinforcement required for the sufficient flexural ductility of reinforced concrete column was investigated. An equation to calculate the required confining reinforcement ratio was deduced from the analytical investigation and examination on the previous experimental data as to the effects of various factors on the required confining reinforcement ratio. The rotation angle required in plastic hinges, the axial force ratio, the material properties such as concrete strength, and the ratio of core area to the whole area of column sections were employed as the factors. From the examination of the equation, it was shown that the ultimate rotation in plastic hinges calculated by the equation was more conservative than the ultimate rotaion angle of members obtained by test column specimens. It was also indicated that the ultimate rotation angle of members of columns failed ...
1991-09-15
Use of X-ray fluorescence analysis in the study of archeological samples
International Nuclear Information System (INIS)
Radionuclide X-ray fluorescence analysis (XFA) was used in the determination of the contents of metal residues in dosing plates for coin minting. XFA was also used for the determination of the strontium/calcium ratio in bone samples of different animals with the aim to obtain information on the food composition of these animals. It was found that bones of different animals can be distinguished based on the Sr/Ca ratio. No significant differences in the Sr/Ca ratio were observed in human bones of individuals from different social groups. (author). 1 fig., 5 tabs., 4 refs.
1988-09-26
International Nuclear Information System (INIS)
The K sub(#alpha#)/K sub(#beta#) intensity ratio of Mn KX-rays scattered by metallic samples changed remarkably with the geometry between the sample and the "5"5Fe source-Si(Li) detector system. On the contrary, this intensity ratio changed little in the cases of non-metallic scatterer samples such as lucite or mylar. This difference is interpreted as due to the occurrence of strong or weak interference in the coherent scattering photons. (author).
1980-01-01
X-Ray Fluorescence Analysis of Composite Propellants for ...
... The constancy of the X-ray intensity ratio for each element in Table 8 as the X-ray tube settings were changed shows the excellent compensating ...
1977-06-03
International Nuclear Information System (INIS)
... obtain the film thickness for a given x-ray intensity ratio. 2.3 ANALYSING FOR
2000-08-01
Study on cold startability and mixture formation of high-percentage methanol blends
Energy Technology Data Exchange (ETDEWEB)
Using gasoline as an example of additives for cold start improvement, fuel vapor composition of methanol-gasoline mixtures, fuel evaporation rate in consideration of temperature drop due to heat of fuel evaporation, air fuel ratio, stoichiometric air fuel ratio and excess air ratio of fuel vapor were calculated. The mixture formation of methanol-gasoline mixtures at low temperature in otto cycle engines was studied. Van Laar's empirical formula was used to estimate the partial pressure of high-percentage methanol blends. It was found that the most part of fuel vapor is occupied by gasoline, even when a small amount of gasoline is added to methanol resulting to an extremely small excess air ratio. It is obvious that this vapor pressure adjustment using gasoline is the dominant factor for improvement in cold startability. (10 figs, 1 tab, 10 refs)
1988-05-31
Starting characteristics of direct current motors powered by solar cells
Energy Technology Data Exchange (ETDEWEB)
Direct current motors are used in photovoltaic systems. Important characteristics of electric motors are the starting to rated current and the torque ratios. These ratios are dictated by the size of the solar cell array and are different for the various dc motor types. The paper deals with the calculation of the starting to rated current ratio and starting to rated torque ratio of the permanent magnet, separately, series and shunt excited motors when powered by solar cells for the two cases: where (1) the system includes a maximum-power-point-tracker (MPPT) and (2) without an MPPT. Comparing these two cases, one gets a torque magnification of about 3 for the permanent magnet motor and about 7 for other motor types at rated design insolation. The calculation of the torques may assist the PV system designer to determine the advantage of including an MPPT in the system as far as the starting ...
1993-03-01
Powertrain and apparatus using a continuously variable ratio transmission to improve fuel economy
Energy Technology Data Exchange (ETDEWEB)
An automotive powertrain includes a conventional piston engine, a continuously variable ratio transmission, an engine speed sensor and a feedback control system. The control system adjusts both the transmission ratio and the throttle valve in the engine carburetor or fuel metering system in response to the position of the accelerator pedal and in response to the crankshaft speed as measured by the engine sensor. The transmission provides extreme overdrive gear ratios which allow the engine to be operated at wide open throttle even during moderate cruising, and, in addition, the engine carburetor or fuel metering system is calibrated to deliver to the engine a stoichiometric air-fuel mixture which is combined, before combustion, with a special proportion of recirculated exhaust gas. As a result of extensive wide open throttle engine operation with the above mentioned intake charge composition, combustion variables are ...
1981-07-28
British Library Electronic Table of Contents (United Kingdom)
The relevance of the mean retention time (MRT) of particles through the gastrointestinal tract (GIT) is well understood and MRTparticleGIT is an important parameter in digestion models. Solute markers have been used to estimate MRTsoluteGIT (or 'fluid passage') in animals, but the relevance of this measure is less evident and is usually sought in its relation to MRTparticleGIT. The ratio between the two measures indicates the degree of 'digesta washing', with little washing occurring at ratios of 1, aborad washing at ratios >1 (where the solute marker travels faster than the particle marker), and orad (retrograde) washing at ratios <1 (where the solute marker travels slower than the particle marker). We analysed digesta washing in a dataset of 98 mammalian species including man of differen...
2011-01-01
Phenomenology of the #LAMBDA#/#SIGMA#production ratio in pp collisions
International Nuclear Information System (INIS)
We show that the recently measured asymmetry in helicity-angle spectra of the #LAMBDA#-hyperons, produced in the reaction pp#->#K"+#LAMBDA#p reaction, and the energy dependence of the total pp#->#K"+#LAMBDA#p cross-section can be explained consistently by the same #LAMBDA#p final-state interaction. Assuming that there is no final-state interaction in the #SIGMA#"0 p channel, as suggested by the available data for the reaction pp#->#K"+#SIGMA#"0p, we can also reproduce the energy dependence of the #LAMBDA#/#SIGMA#"0 production ratio and, in particular, the rather large ratio observed near the reaction thresholds. The nominal ratio of the #LAMBDA# and #SIGMA#"0 production amplitudes squared, i.e. when disregarding the final-state interaction, turns out to be about 3, which is in line with hyperon production data from proton and nuclear targets available at high energies. (orig.)
2006-09-01
On the Z-dependence of K#alpha#_1/K#beta#_1 X-ray intensity ratio
International Nuclear Information System (INIS)
1976. Germany Ramaswamy, MK Birla Inst. of Tech. and Science, Pilani
1976-03-29
On penetration effect in M1 component of 70.45 keV #gamma#-transition in "1"7"7Ta
International Nuclear Information System (INIS)
... gamma radiation l conversion m conversion mev range 10-100 mixing ratio
1987-04-14
Nutating Mechanical Transmission (Maroth Drive Principle)
... d Diameter of ro.'ling element of a cylindrical roller bearing ... L Life (B-10) of a cyl.ndrical roller bearing LACA Contact ratio ...
1974-01-01
New Measurements of the Proton Electromagnetic Form Factor Ratio at Low Q{sup 2}
Energy Technology Data Exchange (ETDEWEB)
Polarization measurements are allowing the electric to magnetic form factor ratio of the proton to be determined with unprecedented precision. Recent results indicate that there is a large deviation from unity in the proton form factor ratio around Q{sup 2}{approx_equal}0.35 GeV{sup 2}. Furthermore, the deviation from unity is attributed to a deviation of the electric form factor from standard fits and calculations. A new, partially completed, experiment will significantly improve the existing data and will determine the presence, if any, of a narrow structure in the form factor ratio. The new measurement, combined with the expected high precision cross section measurements, will allow the extraction of individual form factors with unprecedented accuracy at low Q{sup 2}.
2009-08-15
New Image - ONLY - Scan to PDF - NASA Technical Report Server (NTRS)
ratio 2 with NACA 0005-63 thickness distribution in streamwise planes, and twisted and cambered for a trapezoidal span load distribution has ...
NATIONALAIIVISBRY COMMITTEE Ffltt AERONAUTICS - NASA Technical ...
Watkins,. Charles. E. : Effect of Aspect. Ratio on the Air ...... Grover,. H. 3. ; Bishop,. S. M. ; and. Jackson,. L. R. : Fatigue. Strengths of Aircraft ...
Measurements of K-beta/K-alpha X-ray intensity ratios using VEC beams
International Nuclear Information System (INIS)
An experiment on the K#beta#/K#alpha# characteristic X-ray intensity ratio in silver was performed at VEC Centre, Calcutta using the #alpha#-beams at energies 40 MeV and 50 MeV employing a Si(Li) detector system on-line. The results show that the K#beta#/K#alpha# X-ray intensity ratio at energies 40 and 50 MeV are 0.215 #+-# 0.006 and 0.216 #+-# 0.006, respectively, which indicates no change with beam energy and in accordance with the earlier reports. The present experiment shows the feasibility of studying the K#beta#/K#alpha# ratios as a function of beam energy in different regions of periodic table. Experiments in elements belonging to the 3d shell and their compounds are suggested to look for the chemical effects and their dependence on #alpha#-energy. (author). 7 refs.
1987-02-03
Measurement of K x-ray intensity ratio of tin, gadolinium and dysprosium
International Nuclear Information System (INIS)
Full text: Measurement of K_#beta# to K_#alpha# x-ray intensity ratios are important not only in the field of atomic physics, radiation physics and medical physics, but also to test the validity of assumptions made in the theoretical prediction. The intensity ratios can also give information on the effect of physical and chemical environment of the element in the compound. Many investigators have adopted a single and double reflection geometries to measure the K_#beta# to K_#alpha# x ray intensity ratios to understand the effect of physical and chemical environment on x-ray fluorescence. The targets are excited by a radioactive source of having activity of the order 100 MBq. in order to carry out accurate measurement K_#beta# to K_#alpha# x-ray intensity ratios, we have develop 2#pi# geometrical configuration method : placing a target right on the surface of the detector facing the target to measure the ...
2003-11-01
Mass distribution of fission products from moderately excited sup 236 U compound nucleus
Energy Technology Data Exchange (ETDEWEB)
The chain yields of 30 fission products were determined in 38 MeV {alpha}-particle induced fission of {sup 232}Th. The mass yield curve was found to be primarily asymmtric with a peak to valley (p/v) ratio of 3.5. A small peak has also been observed in the symmetric region. The observed p/v ratio has been resolved into the p/v ratios of the individual mass distributions of the possible fissioning isotopes of uranium formed as a result of multichance fission. An attempt has been made to explain the p/v ratios thus obtained in the light of the available excitation energy in the system. (orig.).
1990-01-01
Manganese, Iodine and Sulfide Concentrations and Peroxide to ...
Manganese, Iodine and Sulfide Concentrations and Peroxide to Oxygen Ratio Measured during the U.S. JGOFS Arabian Sea Process Study ...
Energy Technology Data Exchange (ETDEWEB)
The determination of ratio of neutron over proton matrix elements by inelastic proton scattering, for 0{sup +}{yields}2{sup +} transitions, is investigated via the comparison between experimental data and theoretical calculations. Calculations into the context of a macroscopic and a microscopic description are performed for a wide mass range nuclei: {sup 18}O, {sup 30}Si, {sup 32,34}S, {sup 48}Ca, {sup 88}Sr, for which these ratios were determined previously with an independent technique. At that point the choice of the theoretical model may be very critical. It is thus the purpose of this investigation to point out the most suitable model. It is found that in general both theoretical models can be employed for the reliable determination of neutron over proton matrix element ratios.
1999-12-06
International Nuclear Information System (INIS)
The determination of ratio of neutron over proton matrix elements by inelastic proton scattering, for 0"+#->#2"+ transitions, is investigated via the comparison between experimental data and theoretical calculations. Calculations into the context of a macroscopic and a microscopic description are performed for a wide mass range nuclei: "1"8O, "3"0Si, "3"2","3"4S, "4"8Ca, "8"8Sr, for which these ratios were determined previously with an independent technique. At that point the choice of the theoretical model may be very critical. It is thus the purpose of this investigation to point out the most suitable model. It is found that in general both theoretical models can be employed for the reliable determination of neutron over proton matrix element ratios.
1999-12-06
Failure location analysis for tagged reactor assemblies
The location of defective LMFBR fuel pins by the determination of gas tag isotopic ratios is discussed. The application of this method to the FFTF Reactor briefly described.
1979-03-01
Energy Technology Data Exchange (ETDEWEB)
The measurements of the K X-ray intensity ratio I(K{sub {beta}})/I(K{sub {alpha}}) for the 17 elements Mn, Fe, Co, Ni, Cu, Zn, Ga, Ge, As, Se, Br, Rb, Sr, Y, Zr, Nb and Mo have been done following ionization by 59.5keV {gamma}-rays from a {sup 241}Am point source. Ratios of emission probabilities of Auger electrons and the vacancy transfer coefficients have been extracted in terms of the intensity ratios. It is found that the present results agree well with earlier fitted values and the semi-empirical values.
2006-01-15
Density Gradients for Isolation of Mononuclear Blood Cells for ...
... to-continuum X-ray intensity ratio [5]. For ence in the means [7]. In addition, washing samples on thin films, the characteristic X- lymphocytes in NH ...
2011-05-15
Combustion Mechanisms of 25MM Combustible Cartridge.
... Abstract : The structural features of 25mm combustible cartridge cases, manufactured for this program and having nitrocellulose/resin/fiber ratios of ...
1973-08-01
Color Fluorescence Ratio for Detection of Bronchial Dysplasia and Carcinoma In situ
UK PubMed Central (United Kingdom)
BackgroundAutofluorescence bronchoscopy is more sensitive than conventional bronchoscopy for detecting early airway mucosal lesions. Decreased specificity can lead...Full Text Available
2009-07-15
Antimatter production in supernova remnants
We calculate the energy spectra of cosmic rays (CR) and their secondaries produced in a supernova remnant (SNR), taking into account the time-dependence of the SNR shock. We model the trajectories of charged particles as a random walk with a prescribed diffusion coefficient, accelerating the particles at each shock crossing. Secondary production by CRs colliding with gas is included as a Monte Carlo process. We find that SNRs produce less antimatter than suggested previously: The positron/electron ratio and the antiproton/proton ratio are a few percent and few $\\times 10^{-5}$, respectively. Moreover, the obtained positron/electron ratio decreases with energy, while the antiproton/proton ratio rises at most by a factor of two above 10 GeV.
2011-01-01
A gravitational diffusion model without dark matter
UK PubMed Central (United Kingdom)
In this model, without dark matter, the flat rotation curves of galaxies and the mass-to-light ratios of clusters of galaxies are described quantitatively. The hypothesis is that the agent of gravitational...Full Text Available
1998-03-31
A Computer Program for Wing 'Stibsonic Aerodynamic Performance ...
of Aspect Ratio 2 With NACA 0005-63 Thickness Distribution,. Cambered and Twisted for a Trapezoidal Span Load Distribution. NACA RM A50K27a,, ...
1 - NASA Technical Report Server (NTRS)
having a triangular wing of aspect ratio 2 with NACA 0005-63 thickness distribution in streamwise planes, and twisted and cambered for a trape- ...
Contamination by depleted uranium (Du) in South Serbia
Energy Technology Data Exchange (ETDEWEB)
The paper present the results of the study on D.U. (depleted uranium) contamination in the environment and possible effects on animal healths in the region o f Bujanovac. Samples of soil, feed, leaves, grass, lichen, moss, honey and water were collected randomly in 2003/2004 in the vicinity of the target area (500-1000 m) and 5 km from the target area. Activity of the radionuclides ({sup 226}Ra, {sup 232}Th, {sup 40}K, {sup 210}Pb, {sup 238}U, {sup 235}U, {sup 137}Cs, {sup 7}Be) in soils, grass, lichen, moss and honey was determined on Hp Ge detector (Canberra, relative efficiency 23%) by standard gamma spectrometry. Total alpha and beta activity in water was determined on proportional alpha/beta counter (Canberra 2400, efficiency for alpha emitters 11%, efficiency for beta emitters 30%). Non significantly higher values of concentrations of {sup 226}Ra, {sup 232}Th, {sup 238}U and {sup 235}U were measured in the immediate vicinity of the targeted site, but {sup 235}U/{sup 238}U ...
2006-07-01
X-ray dosimetry of TlGaSe_2 single crystals
International Nuclear Information System (INIS)
TlGaSe_2 compound belongs to group of layered semiconductors of A"3B"3C_2"6-type. Photoelectric and optical properties of TlGaSe_2 single crystals were investigated in detail. Influence of gamma-, electron and neutron radiation on photoelectric properties of TlGaSe_2 single crystals is investigated too. The present work deals with experimental results relative to X-ray dosimetric characteristics of TlGaSe_2 crystals at 300 K. X-ray conductivity and X-ray dosimetric characteristic measurements are carried out in low load resistance regime. The source of X-ray radiation is the installation of X-ray diffraction analysis (URS-55a) with the BCV-2(Cu). Intensity of X-ray radiation (E) is regulated by measurement with current variation in tube at each given value of X-ray radiation dose E (R/min) are measured by crystal dosimeter DRGZ-02. X-ray conductivity coefficients K_#sigma# characterising X-ray sensitivity of investigated crystals are determined as the relative change of conductivity ...
Energy Technology Data Exchange (ETDEWEB)
The study described in this report is part of a project sponsored by the Toronto Atmospheric Fund, performed at the Lawrence Berkeley National Laboratory, to assess the potential role of surface property modifications on energy, meteorology, and air quality in the Greater Toronto Area (GTA), Canada. Numerical models were used to establish the possible meteorological and ozone air-quality impacts of increased urban albedo and vegetative fraction, i.e., ''cool-city'' strategies that can mitigate the urban heat island (UHI), significantly reduce urban energy consumption, and improve thermal comfort, particularly during periods of hot weather in summer. Mitigation is even more important during critical heat wave periods with possible increased heat-related hospitalization and mortality. The evidence suggests that on an annual basis cool-city strategies are beneficial, and the implementation of such measures is ...
2002-04-30
Theory of sexes by Geodakian as advanced by Iskrin
In 1960s V.Geodakian proposed a theory that explains sexes as a mechanism for evolutionary adaptation of the species to changing environmental conditions. In 2001 V.Iskrin refined and augmented the concepts of Geodakian and gave a new and interesting explanation to several phenomena which involve sex, and sex ratio, including the war-years phenomena. He also introduced a new concept of the "catastrophic sex ratio." This note is an attempt to digest technical aspects of the new ideas by Iskrin.
2006-01-01
Second harmonic generation of copper-vapor pulsed laser radiation
Energy Technology Data Exchange (ETDEWEB)
An experimental study of second harmonic generation in a copper-vapor pulsed laser with an ADP crystal is presented. The ratio of the conversion into the second harmonic is found to depend on the average power of the exciting radiation. The maximum conversion ratio was 8.5%. Thermal self-defocusing is the main obstacle to obtaining high average powers at the double frequency.
1980-08-01
Calculation of cosmic ray antiproton-proton ratio
Energy Technology Data Exchange (ETDEWEB)
Independent calculations of the antiproton-to-proton ratio by Gaisser and Maurer and by Badhwar et al. have produced conflicting results which obscure the interpretation of recent measurements of cosmic ray antiprotons. A detailed reexamination of these calculations has been performed and these differences have been resolved. We find that the first calculation was essentially correct and the reported fluxes of antiprotons are significantly higher than expected for secondary antiprotons in conventional models of cosmic ray propagation, as indicated by other recent calculations.
1982-01-15
Calculated fluence spectra at neutron therapy facilities
International Nuclear Information System (INIS)
The Monte Carlo transport codes LAHET and MCNP were used to calculate energy fluence spectra at three neutron therapy facilities. The results compare very favourably with measured data. Kerma spectra and the ratio of ICRU muscle tissue kerma to A-150 kerma, along the carbon to oxygen kerma ratio, were determined. Absorbed dose rate calculations are in reasonable agreement with measured values. Use of these codes to study modifications to existing therapy beams is briefly discussed. (author).
1995-11-13
Antiproton production of propagating cosmic rays under distributed reacceleration
Energy Technology Data Exchange (ETDEWEB)
The available measurements on the cosmic-ray antiproton/proton ratio show an excess of antiprotons above predictions derived in the framework of the standard picture of cosmic-ray origin and propagation. Calculations are performed of the production from collisions of cosmic rays with the interstellar gas under the condition of distributed reacceleration. It could be shown that the calculated antiproton/proton ratio is enhanced compared to that derived from the leaky box model, but it remains difficult to bring it into agreement with the data by reasonable astrophysical assumptions. 15 references.
1987-09-01
Website Policies and Important Links Comments
WorldWideScience.org is maintained by the U.S. Department of Energy's
Office of Scientific and Technical Information as the Operating Agent
for the WorldWideScience Alliance.
