Energy Technology Data Exchange (ETDEWEB)

Success in improving hydropower project efficiency has opened more global markets for variable-speed generator technology. Manufacturers continue to test the markets as the technology evolves. The potential of variable-speed application becomes evident considering that more than 150 pumped storage plants, with a combined capacity exceeding 100,000 MW, are in operation globally.

Science.gov (United States)

This report describes the design, fabrication, installation and testing of a small variable-speed vertical axis wind turbine (VAWT). This VAWT is unique in its installation using hand tools only; unconventional and simple support system; and variable speed operation under microprocessor control. Initial testing confirmed that the turbine can be controlled by commanded alternator field modulation. Further studies will be directed toward determination of an optimum control algorithm.

Science.gov (United States)

The Wind Energy Division at Sandia National Laboratories recently completed a point design based on the 34-m Vertical Axis Wind Turbine (VAWT) Test Bed. The 34-m Test Bed research machine incorporates several innovations that improve Darrieus technology, including increased energy production, over previous machines. The point design differs minimally from the Test Bed; but by removing research-related items, its estimated cost is substantially reduced. The point design is a first step towards a Test-Bed-based commercial machine that would be competitive with conventional sources of power in the mid-1990s.

British Library Electronic Table of Contents (United Kingdom)

Greenman J, Thorn RMS, Saad S, Austin AJ. In vitro diffusion bed, 3-day repeat challenge `capacity' test for antimicrobial wound dressings. Int Wound J 2006;3:322-329. Abstract The aim of this study was to develop an in vitro wound infection model that allows the comparison of the bacterial kill rate of antimicrobial wound dressings over the course of 3 days, with renewed microbial challenges each day, under realistic wound-like conditions. A test bed model of a moderately exuding wound was constructed from a hydrogel containing releasable foetal calf serum (FCS), and cellulose discs dosed with test microbes (Methicillin-resistant Staphylococcus aureus and Pseudomonas aeruginosa) suspended in 50% FCS applied at the interface between the test dressing and the hydrogel test bed. Freshly prep...

British Library Electronic Table of Contents (United Kingdom)

Hydrodynamic regimes and characteristics of air-sand flow were studied in a cone-shape swirling fluidized bed for two types of air entry, or swirl generator: through a four-nozzle system (tangential entry) and using an annular-spiral air distributor (axial entry). Quartz sand of four particle sizes, 180-300, 300-500, 500-600 and 850-1180mm, was used as the bed material in experimental tests on a cold model of a conical swirling fluidized bed combustor. During each test run, the pressure drop across the bed (Dp) was measured versus superficial velocity at the lower bed basis (u) for three static bed heights (20, 30 and 40cm). Four regimes were found in the bed behavior for both swirl generators. The Dp-u diagrams were compared between tangential and axial air entries for different operating...

Science.gov (United States)

... laws between particles (modeling UGV/UAV/UUV collectives) to ... A mobile robot test-bed is used in ... of this work on mobile robots executing pursuit ...

Science.gov (United States)

... 73 DOE/SANDIA 34-Meter VAWT Test Bed ..... ... 8 OPERATING CHARACTERISTICS OF DOE/SANDIA 34 METER VAWT ..... ...

International Nuclear Information System (INIS)

Mercury has had various uses in nuclear fuel reprocessing and other nuclear processes, and so is often present in radioactive and mixed (both radioactive and hazardous according to the Resource Conservation and Recovery Act) wastes. Depending on regulatory requirements, the mercury in the off-gas must be controlled with sometimes very high efficiencies. Compliance to the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards can require off-gas mercury removal efficiencies up to 99.999% for thermally treating some mixed waste streams. Several test programs have demonstrated this level of off-gas mercury control using fixed beds of granular sulfur-impregnated activated carbon. Other results of these tests include: (a) The depth of the mercury control mass transfer zone was less than 15-30 cm for the operating conditions of these tests, (b) MERSORB(reg_sign) carbon can sorb ...

Energy Technology Data Exchange (ETDEWEB)

System-level-operational testing of the ETX-II test-bed electric vehicle is described and the results discussed. Because the traction battery is a major factor in the performance of an electric vehicle, previously reported work on the sodium-sulfur battery designed for use with the ETX-II is reviewed in detail. Chassis dynamometer performance of the test-bed vehicle met or exceeded design goals and compared reasonably well with SIMPLEV computer modeling results. Areas are identified wherein further work is needed to establish a firmer basis for comparison of the simulation and the observed results.

Energy Technology Data Exchange (ETDEWEB)

This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period July 1, 2004 through September 30, 2004. The following tasks have been completed. First, renovation of the new Combustion Laboratory and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building have started. Second, the design if the component parts of the CFBC system have been reviewed and finalized so that the drawings may be released to the manufacturers during the next quarter. Third, the experiments for solid waste (chicken litter) incineration have been conducted using a Thermogravimetric Analyzer (TGA). This is in preparation for testing in the simulated fluidized-bed combustor. The experimental results from this study are presented in ...

Energy Technology Data Exchange (ETDEWEB)

In the atmospheric pressure coal combustion area, the internally circulating fluidized bed boiler (ICFB) has already been proven to possess superior performance features in terms of the ease with which load conditions can be controlled and its low pollution level. Based on the particular merits of the ICFB furnace and the application of this technology to pressurized fluidized bed boiler technology, it was possible to achieve a pressurized fluidized bed boiler with superior ease of operation, reliability and los pollution characteristics. Cold model tests and computer simulation have been carried out to investigate the possibility of applying ICFB technology to the pressurized fluidized bed boiler technology in an attempt to develop the pressurized internally circulating fluidized bed boiler (PICFB). Based on the results achieved in this research, a hot-model ...

Energy Technology Data Exchange (ETDEWEB)

The paper reports a work-in-progress outlook of a R and D project aimed at developing an advanced boiler for the combustion of virgin and exhaust olive husks at small scale. Fluidized bed technology has been preferred because of its well known advantages that include large thermal inertia, high combustion efficiency, low NOx emissions and considerable heat transfer rate. A 100 kW atmospheric bubbling fluidized bed combustor has been designed and built. The facility is equipped with devices for continuous fuel feeding as well as heat extraction from the bed region. Measurements of temperature and gas concentrations are obtained by using thermocouples and gas-analyzer. Steady state tests of combustion were carried out at typical fluidized bed combustion temperatures. Tests proved that not only exhaust olive husks but also the virgin ones - with a water content ...

International Nuclear Information System (INIS)

Nitric acid leaching from the weak base anion (WBA) exchanger had been evaluated and based on this a 5% mixture of nitric acid loaded weak base anion exchanger with fresh weak base anion exchanger (NLWBA) at the bottom of the ion exchange column has been devised to maintain an outlet pH in the range of 5.0 to 5.5 during Gd removal from the moderator system of TAPP - 3 and 4. A three layered bed had been constituted wherein strong acid cation (SAC) exchanger is placed as the top layer while a mixed bed of SAC and WBA or pure WBA is used as the middle layer and the 5% NLWBA was used as the bottom most layer. This bed configuration would result in an iso-pH regime in the moderator system during the Gd removal along with quantitative removal of Gd. Two three-layer bed columns were prepared at TAPS - 3 and 4 in July 07. The resin was loaded in batches and after preparing the column, the column was deuterated ...

Energy Technology Data Exchange (ETDEWEB)

The data center in this study had a total floor area of 3,024 square feet (ft{sup 2}) with one-foot raised-floors. It was a rack lab with 147 racks, and was located in a 96,000 ft{sup 2} multi-story office building in San Jose, California. Since the data center was used only for testing equipment, it was not configured as a critical facility in terms of electrical and cooling supply. It did not have a dedicated chiller system but was served by the main building chiller plant and make-up air system. Additionally it was served by only a single electrical supply with no provision for backup power in the event of a power outage. The Data Center operated on a 24 hour per day, year-round cycle, and users had full-hour access to the data center facility. The study found that data center computer load accounted for 15% of the overall building electrical load, while the total power consumption attributable to the data center including allocated cooling load and lighting was ...

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the progress made on the development of an integrated multistage fluidized bed retorting process (KENTORT II) during the period of October 1, 1992 through September 30, 1993 under Cooperative Agreement No. DE-FC21-90MC27286 with the Morgantown Energy Technology Center, US Department of Energy. The KENTORT II process includes integral fluidized bed zones for pyrolysis, gasification, and combustion of the oil shale. The purpose of this program is to design and test the KENTORT II process at the 50-lb/hr scale. The PDU was assembled, instrumented and tested during this fiscal year. Along with the major activity of commissioning the 50-lb/hr retort, work was also completed in other areas. Basic studies of the cracking and coking kinetics of model compounds in a fixed bed reactor were continued. Additionally, as part of the effort to investigate niche market ...

Science.gov (United States)

Sandia National Laboratories has erected a research oriented, 34- meter diameter, Darrieus vertical axis wind turbine near Bushland, Texas. This machine, designated the Sandia 34-m VAWT Test Bed, is equipped with a large array of strain gauges that have been placed at critical positions about the blades. This manuscript details a series of four-point bend experiments that were conducted to validate the output of the blade strain gauge circuits. The output of a particular gauge circuit is validated by comparing its output to equivalent gauge circuits (in this stress state) and to theoretical predictions. With only a few exceptions, the difference between measured and predicted strain values for a gauge circuit was found to be of the order of the estimated repeatability for the measurement system.

Energy Technology Data Exchange (ETDEWEB)

Tests with a 61 cm diameter fluidized-bed combustor revealed that raw cotton gin trash could be efficiently burned while satisfying Federal standards for particulate emissions. Certain chemicals within cotton gin trash zone can cause slagging or caking of ash and bed particles in the combustion zone. They can also corrode and accumulate on the heat recovery equipment. These problems are not considered insurmountable and methods of control are being studied. Raw cotton gin trash was also converted into a low Btu gas using fluidized-bed technology. Tests with a 30 cm diameter gasifier revealed that raw gin trash could be converted to a combustible gas, containing carbon monoxide and hydrogen. The heating value of the gas ranged from 3.65 to 5.29 MJ/m3 and about 50 percent of the heat value of the raw trash was converted to combustible gases. Economic analyses have shown that these ...

Energy Technology Data Exchange (ETDEWEB)

The control problem associated to a class of horizontal-axis fixed-pitch variable-speed low-power wind energy conversion systems, working in the partial load region, consisting in the energy conversion maximization, is approached here under the assumption that the wind turbine model and its parameters are poorly known. Using a new approach derived from the optimum seeking methods category, generically called Maximum Power Point Tracking (MPPT), the proposed control solution aims at driving the average position of the operating point near to optimality. Instead of inducing sinusoidal search signals, the wind turbulence is here used as search disturbance. The high-speed shaft's average rotational speed is slowly adjusted using the Fast Fourier Transform processing of some available measures from the system as an estimate of the operating point's position/distance to optimality. Numerical simulations are used for preliminary checking the control law ...

Energy Technology Data Exchange (ETDEWEB)

The catalytic dehydration of methanol to dimethyl ether was investigated for application on-board a methanol fuelled vehicle. Several catalysts have been tested in a fixed bed reactor. Our approach is to develop a small and efficient reactor converting liquid MeOH under pressure and at low reaction temperatures. (author) 2 figs., 5 refs.

Energy Technology Data Exchange (ETDEWEB)

Combustion characteristics of Korean anthracite in a circulating fluidized bed and freeboard were investigated. A test coal was selected with heating value of 4,429kcal/kg and ash content of 38%. Characteristics of combustion, sorbent effect on desulphurisation and emission of SO{sub x} and NO{sub x} were monitored by varying process variables such as feed rate, (Ca+K)/S ratio, and excess air ratio at the given properties of coal. Optimum operating conditions were studied by analysing: axial profiles of temperature, effect of excess air ratio, characteristics of loopseal and bag filter ashes, and emission of toxic gases. 9 refs., 9 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

We have investigated and modeled the boron diffusion in silicon following ultra-low-energy implantation (500 eV). It is well known that reducing implant energies is an effective way to eliminate transient enhanced diffusion due to the excess of interstitials from the implant. However, for sub-keV B implants diffusion remains enhanced. This enhancement is linked to the presence of a silicon boride layer located at the silicon surface which creates interstitials. This phenomenon is named 'boron enhanced diffusion' (BED). The BED effect is of obvious interest since it counteracts the advantage obtained by reducing the ion implantation energy. For these reasons, we have investigated the diffusion of low-energy boron implanted in crystalline silicon and tested a complete simulation program, which takes into account the effect of boron precipitation and the effect of the silicon boride layer as a source of ...

Energy Technology Data Exchange (ETDEWEB)

The testing of candidate fuel elements at prototypic operating conditions with respect to temperature, power density, hydrogen coolant flow rate, etc., a crucial component in the development and qualification of nuclear rocket engines based on the Particle Bed Reactor (PBR), NERVA-derivative, and other concepts. Such testing may be performed at existing reactors, or at new facilities. A scoping study has been performed to assess the feasibility of testing PBR based fuel elements at the TREAT reactor. initial results suggest that full-scale PBR, elements could be tested at an average energy deposition of {approximately}60--80 MW-s/L in the current TREAT reactor. If the TREAT reactor was upgraded to include fuel elements with a higher temperature limit, average energy deposition of {approximately}100 MW/L may be achievable.

Energy Technology Data Exchange (ETDEWEB)

The objective of this project is to develop a pellet formulation which is capable of achieving low sulfur partial pressures and a high capacity for sulfur, loaded from a hot fuel gas and which is readily regenerable. Furthermore the pellet must be strong for potential use in a fluidized bed and regenerable over many cycles of loading and regeneration. Regeneration should be in air or oxygen-depleted air to produce a high-concentration sulfur dioxide. Fixed-bed tests were conducted with several formulations of manganese sesquioxide and titania, and alumina They were subject to a simplified fuel gas of the oxygen-blown Shell type spiked with a 30,000ppmv concentration of H{sub 2}S. Pellet crush strengths for 4 and 2mm diameter pellets was typically 12 lbs per pellet and 4 lbs per pellet, respectively. For the most favorable of the formulations tested and under the criteria of break-through at less than ...

Energy Technology Data Exchange (ETDEWEB)

A critical and difficult step in the development and implementation of new technologies for environmental monitoring and characterization is successfully transferring these technologies to industry and government users for routine assessment and compliance activities. The Environmental Sciences Section of the DOE Savannah River Technology Center provides a forum for developers, potential users, and regulatory organizations to evaluate new technologies in comparison with baseline technologies in a well characterized field test bed. The principal objective of this project is to conduct comprehensive, objective field tests of monitoring and characterization technologies that are not currently used in EPA standard methods and evaluate their performance during actual operating conditions against baseline methods. This paper provides an overview of the field test site and a description of some of the ...

Energy Technology Data Exchange (ETDEWEB)

A 100 kW thermal input Two-Stage Gasifier was built at the University of Denmark (DTU). The gasifier consists of an externally heated pyrolysis unit, a down-draft char gasifier, a gas cleaning system and an internal-combustion engine. Between the summer of 1996 and the summer of 1998, 11 tests were made with the gasifier. The gasifier had a total operating time of 278 hours (excluding warming up). The fuel was mainly wood chips, but also briquettes has been used. Four of the tests lasted 50-70 hours, and stable conditions were reached. All the tests were completed without technical problems. The particle sizes and amounts were investigated. The amount of particles depended on the amount of steam led to the gasifier. More than 99% of the particles after the cyclone were soot. The size of the soot particles was mainly between 0.2-0.5 {mu}m. Under normal conditions (biomass:steam = 1:1 (dry mass basis)), the particle load was ...

Energy Technology Data Exchange (ETDEWEB)

Problems relating to electromagnetic compatibility and power quality were discussed, combined with a discussion of the role that consulting engineers can play in resolving them. The need for the consulting engineer to be aware of design specifications of equipment was considered essential. Similarly, the interrelationship between installations using variable speed drives, halogenous lighting systems, capacitor banks, high-voltage power lines, power transformers, etc., and the need for familiarity with the operating characteristics of different types of power systems were stressed as key ingredients to success in ascertaining events and causes of equipment failure or power system problems on the network. The main sources of disturbances, impact of voltage variations, the importance of controlling voltage imbalance, and system protection were summarized. 4 figs.

CERN Document Server

Having always been at the forefront of information management and open access, High-Energy Physics (HEP) proves to be an ideal test-bed for innovations in scholarly communication including new information and communication technologies. Three selected topics of scholarly communication in High-Energy Physics are presented here: A new open access business model, SCOAP3, a world-wide sponsoring consortium for peer-reviewed HEP literature; the design, development and deployment of an e-infrastructure for information management; and the emerging debate on long-term preservation, re-use and (open) access to HEP data.

Energy Technology Data Exchange (ETDEWEB)

A hypothesis on the transition of a fully water-saturated coal bed methane reservoir from single-phase flow through unsaturated flow to the two-phase flow regime was developed and substantiated using field data. The concept of parameter measurement windows was introduced to obtain the required reservoir parameters from flow testing. A new empirical relationship for capillary pressure vs. saturation, referred to as the Fermi distribution, was developed and shown to fit the capillary pressure-saturation data for coal, sandstone, and other consolidated and unconsolidated materials. New approximate analytic solutions for flow to a sink from an infinite coal bed reservoir with desorbing methane have been developed and verified using numerical models for the following cases: (1) single-phase gas flow with desorption; (2) single-phase water flow in fully water-saturated and unsaturated flow regimes. A numerical model based on ...

Energy Technology Data Exchange (ETDEWEB)

This comprehensive, illustrated report for the Swiss Federal Office of Energy (SFOE) by the University of Applied Sciences in Lucerne, Switzerland takes a look at the testing facility at the university that is used to test compact ventilation systems. These feature heat-recovery and return-air heat-pumps and are used in housing built to low energy-consumption standards such as the Swiss 'Minergie' and 'Minergie-P' standards. The primary goal is a technically comprehensive testing programme for compact ventilation units with heat recovery and heat pumps, which can nevertheless be carried out at reasonable cost. In addition to thermal and flow measurements, acoustic measurements are also carried out. The authors quote that the overall assessment provided can also include service and maintenance, materials used and possible problems with thermal bridges. The test ...

Energy Technology Data Exchange (ETDEWEB)

To help confirm correct functioning of an epithermal neutron sonde, we measured tightly bonded water content of selected Nevada Test Site (NTS) drill holes. Tuff and alluvium samples were dried overnight at 105/sup 0/C. The samples were then heated for 45 min in a split tube furnace at 700/sup 0/C. The water that came off due to this heating was collected and the amount recorded. The error in this procedure is +- 0.59 wt %. Total water can be calculated for samples from analyses of free and tightly bonded water contents. The maximum error in this calculation is equivalent to the error in determining the more tightly bonded water. Average total water content values have been assigned to geologic units. These values, in weight fraction, are alluvium 0.14 +- .05 and tuff 0.19 +- .04. Further division of the tuff gives values of Rainier Mesa 0.15 +- .01, Paintbrush 0.18 +- .03, Tunnel Beds 0.20 +- .04, and Grouse Canyon 0.29 +- .02. Statistically ...

International Nuclear Information System (INIS)

Geologic studies in connection with Project Discus Thrower have furnished detailed stratigraphic and structural information about northwestern Yucca Flat, Nevada Test Site. The Paleozoic rocks consist of a lower carbonate sequence, argillite of the Eleana Formation, and an upper carbonate sequence. The distribution of these rocks suggests that both top and bottom of the Eleana are structural contacts, probably thrusts or reverse faults. The overlying tuff includes several units recognized in the subsurface, such as the Fraction Tuff and tuff of Redrock Valley. Other units recognized include bedded tuff associated with the Grouse Canyon Member of Belted Range Tuff, and the Rainier Mesa and Ammonia Tanks Members of the Timber Mountain Tuff. The Timber Mountain and Grouse Canyon are extensively altered to montmorillonite (a swelling clay), possibly as a result of ponding of alkaline water. The overlying alluvium locally contains at the base a ...

UK PubMed Central (United Kingdom)

Animal facilities generate a large amount of used bedding containing excrement as medical waste. We developed a recycling system for used bedding that involves soft hydrothermal processing. In this...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Factors important in choosing between process concepts were mechanical complexity and amenability to scale-up studies. The culmination of this work was a process concept known as Staged Turbulent Bed Retorting Process (STB), which has now been tested in pilot plants. Operating conditions are described. The environment in the retort section can be described as a staged, moving bed of particles, in which a portion of the particles are fluidized at gas velocities well below minimum fluidization velocity of many of the particles. Research and engineering evaluations have established that the STB provides prospects for the responsible development of oil shale resources on a commercial scale. A 320 ton/d semiworks unit, the next technological step, will be commissioned shortly. This unit will be large enough to provide scale-up data for design of modules and to demonstrate the entire process, generating data needed to optimize, ...

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is a promising technology for the combustion of gas or solid fuel with efficient use of energy and inherent separation of CO{sub 2}. Chemical-looping combustion of methane with calcium sulfate as a novel oxygen carrier was conducted in a laboratory scale fixed bed reactor. The effects of reaction temperature, gas flow rate, sample mass, and particle size on reduction reactions were investigated and an optimum operating condition was determined. The results show that this novel oxygen carrier has a high reduction reactivity and stability in a long-time reduction/oxidation test. The conversions of CH{sub 4} increased with a higher temperature, smaller gas flow rate, larger sample mass and smaller particle size. The suitable reaction temperature seems to be around 950 C. Low temperatures lead to a low CH{sub 4} conversion, but a significant SO{sub 2} formation was observed at a higher temperature. The release of SO{sub ...

Energy Technology Data Exchange (ETDEWEB)

An investigation was conducted into alternative techniques for zinc and electrolyte regeneration and reuse in the refuelable zinc/air battery that was developed by LLNL and previously tested on a moving electric bus using cut wire. Mossy zinc was electrodeposited onto a bipolar array of inclined Ni plates with an energy consumption of 1.8 kWh/kg. Using a H{sub 2}-depolarized anode, zinc was deposited at 0.6 V (0.8 kA/m{sup 2}); the open circuit voltage was 0.45 V. Three types of fuel pellets were tested and compared with results for 0.75 mm cut wire: spheres produced in a spouted bed (UCB); coarse powder produced by gas-atomization (Noranda); and irregular pellets produced by chopping 1-mm plates of compacted zinc fines (Eagle-Picher, Inc.). All three types transported within the cell. The coarse powder fed continuously from hopper to cell, as did the compacted pellets (< 0.83 mm). Large particles (> 0.83 mm; ...

Energy Technology Data Exchange (ETDEWEB)

Three different configurations of cylindrical submerged media anaerobic reactors (SMARs) with packing volumes of 85 items were operated at 35 C for 415 days with COD loading rates varying from 1 to 12 g/l/d and three retention times of 0.5, 1, and 2 days. A synthetic waste consisting of a milk solution with a mineral supplement was used for the feed. Tracer studies on clean-bed and dirty-bed SMARs indicate that reactor configuration, biogas mixing, and biomass accumulation all have a significant effect on SMAR hydraulics and cause short-circuiting. Based on the isothermal energy dissipation theory, the higher hydrostatic pressures resulting from higher SMAR heights increases self-induced biogas mixing and improves the contact efficiency between substrate and organisms. Based on TCOD removal rate, the tallest SMAR performed slightly better at COD loading rates above 4/g/l/d. At COD loading rates equal to or below 4 g/l/d, there was little ...

International Nuclear Information System (INIS)

Full text: During JET operations, tritium contaminated waste is generated principally but not exclusively from 'intervention' work and from removing or replacing redundant items. It is essential for JET and for any future fusion plant to have available a route for managing each waste stream however large or small, both during operation and decommissioning of the plant. The long term outcome is to have for each tritiated waste stream from JET a route for its management leading to its eventual disposal or recycling (and thus to be available for similar waste streams which will be produced by ITER operations). Since several years SCK#centre dot#CEN has been developing techniques for the treatment of tritiated waste. Amongst them, technologies for water detritiation, for the treatment of tritiated organic liquids and for the decontamination of several types of solid tritiated waste. Our R and D focuses on the development of a system to decontaminate surface contaminated metals, concrete ...

Energy Technology Data Exchange (ETDEWEB)

Revolving type fluidized-bed technology, developed by Ebara Corp., is installed in more than 100 facilities worldwide. The technology is applied for waste, coal and in situations where a conventional fluidized bed is difficult to use. Waste and/or coal can be treated and valuable energy can be recovered from a non-renewable source. This paper describes the application of the revolving fluidized bed for waste, coal and tyres.

Energy Technology Data Exchange (ETDEWEB)

A zinc-air battery in a case including a zinc particle bed supported adjacent the current feeder and diaphragm on a porous support plate which holds the particles but passes electrolyte solution. Electrolyte is recycled through a conduit between the support plate and top of the bed by convective forces created by a density of differential caused by a higher concentration of high density discharge products in the interstices of the bed than in the electrolyte recycle conduit.

Energy Technology Data Exchange (ETDEWEB)

Test bed trials of the Sulzer RTA84 dual-fuel engine were successfully completed at the IHI Aioi engine works (Japan) in April 1986. This newly-developed engine-type, output range 15 to 40 MW, can be operated with both diesel or heavy oil and methane gas at comparable thermal efficiency and unchanged output. The RTA dual-fuel engine was developed in close collaboration between Sulzer Brothers Limited and its Japanese licenses. Intended for the propulsion of LNG carriers, where the boil-off gas from the ship's cargo is exploited for the generation of electricity in stationary plants, the RTA dual-fuel engines is an economic and reliable alternative to the steam or gas turbine. The performance of the engine is discussed.

British Library Electronic Table of Contents (United Kingdom)

Heat transfer through the gas diffusion layer (GDL) is a key process in the design and operation of a PEM fuel cell. The analysis of this process requires the determination of the effective thermal conductivity as well as the thermal contact resistance between the GDL and adjacent surfaces/layers. The Part 1 companion paper describes an experimental procedure and a test bed devised to allow separation of the effective thermal conductivity and thermal contact resistance, and presents measurements under a range of static compressive loads. In practice, during operation of a fuel cell stack, the compressive load on the GDL changes. In the present study, experiments are performed on Toray carbon papers with 78% porosity and 5% PTFE under a cyclic compressive load. Results show a significant hy...

Energy Technology Data Exchange (ETDEWEB)

The energy dispersive beamline X6A at the National Synchrotron Light Source employs a curved crystal monochromator (polychromator) which focuses a range ([similar to]1 keV) of x-ray energies into a narrow (100--120 [mu]m) line image. Although this beamline was constructed primarily for time-dependent EXAFS experiments, we have begun to explore the use of this instrument for energy dispersive diffraction experiments with different types of sample including macromolecular crystals. The tunability ([ital E]=6.5 to 21 keV) and flexibility ([Delta][ital E]=100--1000 eV) of the instrument makes the beamline ideal as a test bed for the application of polychromatic single-crystal diffraction techniques to different chemical or biological materials.

Energy Technology Data Exchange (ETDEWEB)

A prototype hydride storage bed, using LaNi{sub 4.25}Al{sub 0.75} as the storage material, was fitted with strain gages to measure strains occurring in the stainless steel bed vessel caused by expansion of the storage powder upon uptake of hydrogen. The strain remained low in the bed as hydrogen was added, up to a bed loading of about 0.5 hydrogen to metal atom ratio (H/M). The strain then increased with increasing hydrogen loading ({approximately} 0.8 H/M). Different locations exhibited greatly different levels of maximum strain. In no case was the design stress of the vessel exceeded.

Energy Technology Data Exchange (ETDEWEB)

FIU-HCET participated in an ICT meeting at Mound during the second week of December and presented a brief videotape of the testing of the Robotic Climber technology. During this meeting, FIU-HCET proposed the TechXtract technology for possible testing at Mound and agreed to develop a five-page proposal for review by team members. FIU-HCET provided assistance to Bartlett Inc. and General Lasertronics Corporation in developing a proposal for a Program Opportunity Notice (PON). The proposal was submitted by these companies on January 5, 1999. The search for new equipment dismantlement technologies is continuing. The following vendors have responded to requests for demonstration: LUMONICS, Laser Solutions technology; CRYO-BEAM, Cryogenic cutting technology; Waterjet Technology Association, Waterjet Cutting technology; and DIAJET, Waterjet Cutting technology. Based on the tasks done in FY98, FIU-HCET is working closely with Numatec Hanford ...

Energy Technology Data Exchange (ETDEWEB)

Initially, the decision of the operator in Dortmund-Derne to select the impact-type separator concept is explained. None of the tenderers for this 52 t/h boiler could supply references for this fluidized bed steam generator concept with staged combustion in a high-expansion fluidized bed. Under the circumstances, the simple configuration of the Steinmueller fluidized bed steam generator, its compact construction, the reduced amount of refractory and the operational behaviour of the boiler resulting therefrom were decisive in the operator`s decision to select this concept. The development schedule shows the individual stages from cold and hot trials in various test rigs and pilot plants to the final design. So far, this fluidized bed steam generator concept has been realized in the plants Derne (52 t/h), commissioned in November 1989, and Brilon (100 t/h), commissioned in November ...

Energy Technology Data Exchange (ETDEWEB)

The simulation of the Auxiliary Charcoal Bed (ACB) Vacuum System was performed to evaluate the original vacuum system design, detect and identify design deficiencies, investigate the effects of proposed corrections on system performance, and generally aid in refining the system design before construction and mockup testing. The simulation was performed by using the Advanced Continuous Simulation Language (ACSL). The vacuum system design goals are to provide approximately 20 SCFM of both booster gas and purge gas through the system and maintain a flow of approximately 40 SCFM with a velocity of 50 to 75 f/sec at the entrance to the cyclone separator. The model results showed that the original system design was incapable of meeting the system performance goals. Further simulations showed that the following modifications to the original vacuum system design were required to make the system performance acceptable; (1) Remove valve PCV4. (2) Modify ...

Energy Technology Data Exchange (ETDEWEB)

Given that fossil fuel fired power plants are among the largest and most concentrated producers of CO{sub 2} emissions, recovery and sequestration of CO{sub 2} from the flue gas of such plants has been identified as one of the primary means for reducing anthropogenic CO{sub 2} emissions. In this study, ALSTOM Power Inc. (ALSTOM) has investigated several coal fired power plant configurations designed to capture CO{sub 2} from effluent gas streams for use or sequestration. Burning fossil fuels in mixtures of oxygen and recirculated flue gas (made principally of CO{sub 2}) essentially eliminates the presence of atmospheric nitrogen in the flue gas. The resulting flue gas is comprised primarily of CO{sub 2}. Oxygen firing in utility scale Pulverized Coal (PC) fired boilers has been shown to be a more economical method for CO{sub 2} capture than amine scrubbing (Bozzuto, et al., 2001). Additionally, oxygen firing in Circulating Fluid Bed Boilers (CFB's) can be ...

International Nuclear Information System (INIS)

One of the design targets for the ITER Tokamak Exhaust Processing system is not to lose more than 10"-"5 g h"-"1 into the Normal Vent Detritiation System of the Tritium Plant. The plasma exhaust gas, therefore, needs to be processed in a way that an overall tritium removal efficiency of about 10"8 is reached. Such a high decontamination factor can only be achieved by multistage processes. The third step of the three step CAPER process developed at the TLK is based on a so-called permeator catalyst (PERMCAT) reactor, a direct combination of a Pd/Ag permeation membrane and a catalyst bed. The PERMCAT principle is based on isotopic swamping in a counter current mode. Previous tritium experiments employing laboratory scale PERMCAT reactors have revealed decontamination factors as high as 10"5 for the third CAPER step. First tritium tests with a technical scale PERMCAT reactor led to similar decontamination factors and clearly demonstrated that the ...

Energy Technology Data Exchange (ETDEWEB)

Pilot-scale pyrolysis units have been in operation since 1980 to test the efficiency of thermal treatment of transuranic (TRU) solid waste to retrieve the TRUs and to reduce the volume of wastes such as spent solvent, spent resin, and others. These wastes are generated by reprocessing, fuel production, and utilities. NUKEM has developed a criticality-safe, ring-slab reactor to decompose solid TRU waste. The plant processes 25 kg/h with a polyvinyl chloride content up to 70%. The overall throughput (inactive) up to the spring of 1982 was 2000 kg. The decontamination factor for the reactor itself is 1000. The liquid wastes, mainly spent solvent, are cracked under nitrogen at 400 to 700/sup 0/C in a reactor that is filled by a packed bed kept in motion by a specially designed agitator. This unit was built for 15 kg/h water equivalent evaporation. Up to 1982 the unit processed 2000 kg of spent solvent (simulated) overall. The decontamination factor ...

Energy Technology Data Exchange (ETDEWEB)

This report discusses Test Campaign TC07 of the Kellogg Brown & Root, Inc. (KBR) Transport Reactor train with a Siemens Westinghouse Power Corporation (Siemens Westinghouse) particle filter system at the Power Systems Development Facility (PSDF) located in Wilsonville, Alabama. The Transport Reactor is an advanced circulating fluidized-bed reactor designed to operate as either a combustor or a gasifier using a particulate control device (PCD). The Transport Reactor was operated as a pressurized gasifier during TC07. Prior to TC07, the Transport Reactor was modified to allow operations as an oxygen-blown gasifier. Test Run TC07 was started on December 11, 2001, and the sand circulation tests (TC07A) were completed on December 14, 2001. The coal-feed tests (TC07B-D) were started on January 17, 2002 and completed on April 5, 2002. Due to operational difficulties with the reactor, ...

Energy Technology Data Exchange (ETDEWEB)

This study investigated the effectiveness of dealing with biological waste by composting. In particular, it examined the feasibility of recovering excess thermal energy produced in the process of composting biological waste in terms of mass and energy transport parameters required in the aerated compost bed. An experiment was performed in which a 100 dm{sup 3} adiabatic, leak-tight reactor equipped with a controlled aeration system was constructed to study the temperature and pressure distribution in the bed. Sensors were used to determine the amount and humidity of emitted gases under variable external physical conditions. The perforated bottom of the reactor allowed for bed aeration. As such, the humidity and heat were transported upwards, forced by the air pumped in and by natural convection. In terms of pressure distribution inside the composted and aerated bed, the study results showed that there ...

Scientific Electronic Library Online (English)

Abstract in english A simplified model for drying solids in the constant rate period in a batch fluidised bed was developed.It assumes the bed to be divided into dense and bubble phases with heat and mass transfer between the phases.The model predicts the constant-rate drying period, provided the fluid bed shape and material characteristics are known.The model is compared with experimental data reported in the literature covering a wide range of materials, gas flow rates, column diameters, m (more) aterial hold-ups, air temperatures and humidities.Model predictions compare satisfactorily with the experimental data.

Energy Technology Data Exchange (ETDEWEB)

The Devonian oil shales of the Eastern United States are a significant domestic energy resource. The overall objective of the multi-year program, initiated in October 1987 by the US Department of Energy is to perform the research necessary to develop the Pressurized Fluidized-Bed Hydroretorting (PFH) process for producing oil from Eastern oil shales. The program also incorporates research on technologies in areas such as raw shale preparation, beneficiation, product separation, and waste disposal that have the potential of improving the economics and/or environmental acceptability of recovering oil from oil shales using the PFH process. The results of the original 3-year program, which was concluded in May 1991, have been summarized in a four-volume final report published by IGT. DOE subsequently approved a 1-year extension to the program to further develop the PFH process specifically for application to beneficiated shale as feedstock. Studies have shown that ...

Energy Technology Data Exchange (ETDEWEB)

The Coal Fired Combined Cycle (CFCC) is the unique powerplant concept developed under the leadership of the General Electric Company to provide a direct coal-burning gas turbine and steam turbine combined cycle powerplant. On the basis of previous studies and confirming work under this contract, General Electric continues to believe that the CFCC approach offers important advantages over alternate approaches: higher powerplant efficiency in the combustor temperature range of interest; reduced combustor/steam generator corrosion potential, due to low fluid-bed tube temperature (as contrasted to the air in tube cycle); and increased gas turbine bucket life from improved material protection systems. The objective of this program is to evaluate the coal fired combined cycle powerplant conceptual design, and to conduct a supporting development program. The supporting development is required for evaluating the pressurized fluidized bed combustion ...

Energy Technology Data Exchange (ETDEWEB)

A joint materials test program developed by the Institute for Mining and Minerals Research (IMMR) and the Tennessee Valley Authority (TVA) involved the postexposure mechanical properties and corrosion behavior of candidate structural materials in an experimental, atmospheric fluidized-bed combustor (AFBC). This combustor was operated by Accurex Corporation at Research Triangle Park, North Carolina, under the direction of TVA. The materials studied were Type 304, Type 310, and INCOLOY alloy 800 in the form of disc coupons with and without crevice configurations. Type 304 was also used for mechanical property measurements. The alloys were exposed to the combustor environment at about840/sup 0/C for approximately 330 hours. The ranking in terms of decreasing weight loss was: (1) Type 304, (2) Type 310, and (3) INCOLOY alloy 800. The presence of tight crevices did not enhance the corrosion rate. In addition, the corrosion rates, based on the weight ...

Energy Technology Data Exchange (ETDEWEB)

This Guideline provides a set of procedures for the measurement of organic contaminants and particles in producer gases from biomass gasifiers. The procedures are designed to cover different gasifier types (updraft or downdraft fixed bed or fluidised bed gasifiers), operating conditions (0 - 900C and 0.6-60 bars) and concentration ranges (1 mg/m{sub n}{sup 3} to 300 g/m{sub n}{sup 3}). The Guideline describes a modular sampling train, and a set of procedures, which include: planning and preparation of the sampling, sampling and post-sampling, analysis, calculations, error analysis and reporting. The modular sampling train consists of 4 modules. Module 1 is a preconditioning module for isokinetic sampling and gas cooling. Module 2 is a particle collection module including a heated filter. Module 3 is a tar collection module with a gas quench (optionally by circulating a liquid), impinger bottles and a backup adsorber. Module 4 is a ...

British Library Electronic Table of Contents (United Kingdom)

Purpose The aim of this study was to evaluate the role of host periosteum and recipient bed perforation on the healing of an onlay graft to the mandible based on histologic and immunohistochemical analysis. Materials and methods Each of the 12 adult sheep used in the study received four iliac corticocancellous onlay bone grafts on the lateral surface of the mandible. In experiment 1, the block graft was placed in direct contact with the recipient bed and fixed with micro-screws, and in experiment 2, the recipient cortical bed was perforated before graft placement. The host periosteum around the graft was excised before flap replacement in experiment 3, and in experiment 4, a sheet of silicone membrane was placed between the graft and the recipient bed. The animals were euthanised at 4, 8, ...

Energy Technology Data Exchange (ETDEWEB)

Concerning the transient phenomenon of solid-gas two-phase flow, an attempt was made to visualize and measure a flow phenomenon in which three-dimensional bubbles occurred, grew and collapsed in the vicinity of a gas injection nozzle while solid particles were circulating. Such a phenomenon could not or hardly be visualized and measured by conventional methods. Such two-phase flow was visualized using neutron radiography, its characteristics measured and the usefulness of the visualization by neutron radiography confirmed. For this purpose, three-dimensional fluidized bed vessels, rectangular or cylindrical-shaped, made of steel or aluminum sheet, were prepared. Polyethylene or glass beads were used as solid particles and activated carbon particles as the tracer. In the experiment, nitrogen gas was blown into the vessel from one nozzle and distributors provided at the bottom of the vessel and exhausted from the top via the exhaust valve, by which the pressure in ...

Energy Technology Data Exchange (ETDEWEB)

WIPP, intended for underground permanent disposal of defense transuranic waste, is located 40 km east of Carlsbad at a depth of 655 m in the salt beds of the 600-m thick Permian Salado Formation. It will consist of 56 ``rooms`` each 91.5 m long, 10 m wide, and 4 m high, grouped in 8 ``panels`` of 7 rooms each. About 7.5 km of access drifts will also be provided. Excavation began in 1982 and surface/access/test facilities and one panel were completed by 1988, many years before it could be used. Current plans are to start emplacing waste in WIPP in 1998 and continue for 35 years. The north- south drift E140 is the widest (25 ft) of the four main north-south drifts and is the main north-south passage. Plans to conduct experiments with waste in 1993 were abandoned, and the plan now is to use panel 1 for permanent disposal of waste starting in 1998. The stability evaluation resulted in the conclusion that, while it would be possible to safely use ...

Energy Technology Data Exchange (ETDEWEB)

Olive bagasse (Olea europea L.) was pyrolysed in a fixed-bed reactor. The effects of pyrolysis temperature, heating rate, particle size and sweep gas flow rates on the yields of the products were investigated. Pyrolysis runs were performed using pyrolysis temperatures between 350 and 550 {sup o}C with heating rates of 10 and 50 {sup o}C min{sup -} {sup 1}. The particle size and sweep gas flow rate varied in the ranges 0.224-1.8 mm and 50-200 cm{sup 3} min {sup -1}, respectively. The bio-oil obtained at 500 {sup o}C was analysed and at this temperature the liquid product yield was the maximum. The various characteristics of bio-oil obtained under these conditions were identified on the basis of standard test methods. The empirical formula of the bio-oil with heating value of 31.8 MJ kg{sup -1} was established as CH{sub 1.65}O{sub 0.25}N{sub 0.03}. The chemical characterization showed that the bio-oil obtained from olive bagasse may be ...

Energy Technology Data Exchange (ETDEWEB)

Advanced coal-fired combined-cycle power systems under development and demonstration have the potential to increase generating efficiency to approach 50%, reduce the cost of electricity by up to 20%, and meet stringent standards on emissions of SO{sub x}, NO{sub x}, fine particulates, and air toxic metals. Integrated gasification combined cycle, pressurized fluidized-bed combustion, and externally fired combined cycle systems rely on different high-temperature combinations of heat exchange, gas filtration, and sulfur capture to meet these requirements. The success of these systems when operated on low-rank coals depends importantly on the behavior of the ash. This paper focuses on the behavior of ash in an intermediate-scale transport gasifier coupled with a hot-gas cleanup system. The work reported is part of the overall program on hot-gas cleanup and the transport reactor development unit (TRDU) located at the Energy and Environmental Research Center (EERC), ...

Energy Technology Data Exchange (ETDEWEB)

Heat transfer through the gas diffusion layer (GDL) is a key process in the design and operation of a PEM fuel cell. The analysis of this process requires determination of the effective thermal conductivity as well as the thermal contact resistance associated with the interface between the GDL and adjacent surfaces/layers. In the present study, a custom-made test bed that allows the separation of effective thermal conductivity and thermal contact resistance in GDLs under vacuum and ambient conditions is described. Measurements under varying compressive loads are performed using Toray carbon paper samples with a porosity of 78% for a range of thicknesses. The measurements are complemented by compact analytical models that achieve good agreement with experimental data. A key finding is that thermal contact resistance is the dominant component of the total thermal resistance; neglecting this phenomenon may result in significant errors in ...

Energy Technology Data Exchange (ETDEWEB)

The overall objective of this research work was to prepare hydrocracking catalysts using amorphous silica-alumina (ASA) supports in combination with USY and {beta}-zeolites. Three supports: namely silica-alumina, USY and {beta}-zeolites were selected to prepare the extrudates using AP-1 as a binder, while two metal pairs: namely Ni-W and Ni-Mo were loaded on the extrudates through co-impregnation using incipient wetness technique. The catalysts were then calcined at 550C for 2h. The catalysts were tested in a fixed-bed flow reaction system for their activity, using desulfurized vacuum gas oil (DS-VGO) as a feedstock. The catalytic evaluation results of the catalysts showed that {beta}-zeolite alone and in combination with the ASA used in this study, has a potential as a support for developing heavy oil hydrocracking catalysts. A balance of weak and strong acidities of {beta}-zeolite provides control cracking, while high surface area and bigger ...

British Library Electronic Table of Contents (United Kingdom)

Cobalt supported on Beta zeolite catalysts were prepared by impregnation of metal salts in aqueous solution and were tested for the Fischer Tropsch reaction. The support consisted of a Beta zeolite composed by crystallites of nanometric dimensions and a SiO2/Al2O3 molar ratio of about 50. This support was impregnated with Co(NO3)2 aqueous solution using different metal loads of 7.5, 10, 15 and 20wt% Co. These materials were characterized by X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM), N2 adsorption (BET), thermal programmed reduction (TPR) and FTIR of adsorbed pyridine (i.e., surface acid sites distribution). All the catalysts showed a significant catalytic activity for the F-T reaction from synthesis gas (CO+2H2), in a continuous fixed bed reactor sys...

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is a two-stage process proposed as an alternative for the combustion of carbonaceous materials, such as natural gas or coal gas, for almost complete CO{sub 2} capture. In the reduction stage, the structural oxygen contained in the lattice of a reducible inorganic oxide, is used for combustion of the carbonaceous material. In the regeneration stage the oxygen carrier, found in a reduced state after the reduction stage, is regenerated with pure air to recover the physical and chemical properties of the carrier, ready to reinitiate a new cycle reduction-regeneration. In a typical multicycle reactor test, the carriers are subjected to accumulative chemical and thermal stresses and the performance will, probably, decay progressively with the number of cycles. The occurrence of some side reactions may limit the efficiency of the overall process in CO{sub 2} capture. In this paper, titania-supported iron oxides with different iron loadings have ...

Energy Technology Data Exchange (ETDEWEB)

The Coal Fired Combined Cycle (CFCC) power system thermodynamic cycle is illustrated schematically. Pressurized air supplied at the discharge of gas turbine compressors is ducted to the pressure vessel of pressurized, fluidized-bed, combustor-steam generator modules. The air is introduced in parallel to the beds, entering through distribution grids beneath each bed. Steam generation tubes are buried within the beds and are also arranged as membrane tube walls enclosing the four sides. Crushed coal (1/4 inch x 0) is pneumatically fed at locations just above the air inlet grids at the bottom of each bed. Dolomite is similarly fed to the individual beds. The coal is burned at a temperature below the ash fusion point. Sulfur is removed in the fluid beds through reaction of the SO/sub 2/ with CaCO/sub 3/ and O/sub 2/ to form solid CaSO/sub 4/ and ...

Energy Technology Data Exchange (ETDEWEB)

A fluidized bed combustor of 0.146 m diameter and 1 m length was fabricated from stainless steel to burn olive cake. Initially, and in order to obtain fluidization, the system was operated under cold conditions using a sand with particle size in the range of 500 to 710 microns. The continuous combustion experiments were carried out under controlled conditions, such that the effects of bed temperature, olive cake feed rate, fluidization velocity, and particle size on combustion efficiency and flue gas composition were investigated. It was found that the combustion efficiency decreases with the bed temperature, fluidization velocity, and the feed rate, while it increases with the particle size used. Further, the gas products analysis carried out using a gas chromatography analyzer have shown a nonmeasured amount of SO2, and small amounts of CO. Finally, the temperature distribution along the bed indicated ...

Energy Technology Data Exchange (ETDEWEB)

Carbon monoxide, H{sub 2}, and CO{sub 2} in synthesis gas can be converted to CH{sub 4} by employing a triculture of Rhodospirillum rubrum, Methanosarcina barkeri, and Methanobacterium formicicum. Trickle-bed reactors have been found to be effective for this conversion because of their high mass-transfer coefficients. This paper compares results obtained for the conversion of synthesis gas to CH{sub 4} in 5-cm- and 16.5-cm-diameter trickle-bed reactors. Mass-transfer and scale-up parameters are defined, and light requirements for R. rubrum are considered in bioreactor design.

Energy Technology Data Exchange (ETDEWEB)

In 1980 Sasol completed its very large coal conversion complex, Sasol Two and Three in South Africa. This complex, the largest coal-to-liquids facility in the world, utilizes Sasol's proprietary Fischer-Tropsch technology, the Synthol Process. The two key elements of the Synthol Process are its catalyst and its unique fluidized bed reactor, the Synthol Circulating Fluidized Bed Reactor. Details on the catalytic aspects and reaction mechanism have been given elsewhere. In this paper, the history of the development of the reactor is discussed.

International Nuclear Information System (INIS)

Purpose: The occurrence of extraosseous Ewing's sarcoma (ES) in deep soft tissues has been well described, but cases in which this tumor occurs in a primary cutaneous or subcutaneous site have rarely been reported. The superficial variant may be less aggressive than are the more common bony and deep soft tissue counterparts with an apparently favorable outcome. A retrospective review of patients with cutaneous or subcutaneous ES was conducted to analyze outcome and patterns of failure. Methods and Materials: Between July 1985 and March 1997, 14 patients with cutaneous or subcutaneous ES were treated at St. Jude Children's Research Hospital. The median age at presentation was 16 years (range 7-21 years). Anatomic locations included trunk and pelvis (7), upper or lower extremity (4), and head and neck (3). The median size of the lesion was 3 cm (range, 1-12 cm). Thirteen had definitive surgical resections, and one had biopsy of the mass at the time of referral. They were enrolled on ...

Energy Technology Data Exchange (ETDEWEB)

The coal-fired combined cycle with partial gasification and fluidized bed combustion (PGFBC-CC), also referred to as a hybrid cycle, has advantages of staged energy conversion and utilization, which can attain high thermal efficiency with low emissions. Four kinds of PGFBC-CC are studied in this paper, two based on pressurized fluidized bed combustion (PFBC) and two on atmospheric fluidized bed combustion (AFBC). Thermal performance calculations and parametric analyses were performed. On the basis of the results, from the above analyses, the best integration system for China is suggested. In addition, a preliminary exergetic analysis is carried out for three of the PGFBC-CC variants.

International Nuclear Information System (INIS)

Available in abstract form only. Full text of publication follows: In this study. simulation of carbon dioxide absorption by Sodium Hydroxide solution in a packed bed has been investigated. At first, mass and energy balances were applied around a differential height of the bed. So, the governing equations were obtained. Surface renewal theory by Danckwerts was used to represent the mass transfer operation Finally, by changing the operating parameters like solvent temperature, inlet gas composition pressure and height of the bed, the effect of these parameters on the absorption and the composition of carbon dioxide in exit stream have been investigated. (authors)

Science.gov (United States)

your eye to the SCN in your brain, so that light ... Owls are individuals who go to bed late, like to get up late in the moming. And the moming types, ...

Energy Technology Data Exchange (ETDEWEB)

This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period October 1, 2004 through December 31, 2004. The following tasks have been completed. First, the renovation of the new Combustion Laboratory and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building have proceeded well. Second, the detailed design of supporting and hanging structures for the CFBC was completed. Third, the laboratory-scale simulated fluidized-bed facility was modified after completing a series of pretests. The two problems identified during the pretest were solved. Fourth, the carbonization of chicken waste and coal was investigated in a tube furnace and a Thermogravimetric Analyzer (TGA). The experimental results from this study are presented in ...

Energy Technology Data Exchange (ETDEWEB)

This report forms part of an independent review of the specifications, execution and results of Task 6 of the Aespoe Task Force on Modelling of Groundwater Flow and Transport of Solutes, which is seeking to provide a bridge between site characterization (SC) and performance assessment (PA) approaches to solute transport in fractured rock. The present report is concerned solely with Task 6C, which relates to the construction and parametrisation of a block-scale hydrostructural model of the TRUE Block Scale region of the Aespoe Hard Rock laboratory. The task objectives, specifications and outcome are summarised and reviewed. Also, consideration is given to how the hydrostructural model might affect the outcomes of Task 6D and 6E. The main conclusions of this review are summarised below: The Task 6C hydrostructural model is a more comprehensive approach to quantitatively describing a volume of fractured rock than has been achieved hitherto. The idea of including solute retention ...

Science.gov (United States)

Under different sintering temperatures(340 degrees C, 440 degrees C, 540 degrees C, 640 degrees C), four TiO2 particles were prepared. The crystal types of all four samples were found to possess anatase structures by XRD. It was obtained by N2 experimental adsorption at low temperature (77K) that their surface areas and average pore size were between 79 and 124 m2/g, 56.8 and 254.8 A respectively. The pore structure of TiO2 particles was characterized by scanning electron microscope (SEM). The tests of adsorption dynamics for FGD and the performance of SO2 removal were investigated in a fixed-bed system for different samples. The results show that SG540 sample which made at 540 degrees C sintering temperature had the most quality among the four samples. It can adsorb SO2 of 38.9 mg for one gram SG540 sample. Different operating conditions for SG540 such as adsorption temperature, SO2 concentration in flue gas and the superficial velocity of ...

International Nuclear Information System (INIS)

Between December 2001 and May 2004, a ventilation experiment (VE) was performed in the Mont Terri Underground Research Laboratory (URL) and co-financed by the Commission of the European Communities. The objective was to investigate the desaturation of consolidated clay formations in consequence of the ventilation of underground openings of a repository in such a formation. The results of the geoelectric measurements performed in the second phase of the Mont Terri ventilation test can be summarized as follows: Geoelectric tomography has been found suitable for monitoring ventilation-induced saturation changes in the Opalinus clay. During ventilation with dry air a desaturation down to below 50% could be detected in both desaturation cycles. The desaturated zone extends less than 0.5 m into the rock around the microtunnel. During the second resaturation phase, ventilation with humid air led to quick resaturation at the tunnel surface, while resaturation of the rock ...

Energy Technology Data Exchange (ETDEWEB)

In January 1981, a dual-fuel engine of type 8L52/55 ADG, with the highest cylinder rating of all four-stroke gas engines currently available, succesfully completed its test run on M.A.N.s test bed at Augsburg. The engine can be operated either on Diesel oil or on gas and pilot oil and can be switched from Diesel to gas operation or vice versa at any load during operation. In gas operation, the engine works on the pilot injection principle. By changing from pulse-pressure to constant-pressure turbocharging, matching the charge-air pressure, improving mixture formation and optimising the injection system, M.A.N. has succeeded in achieving a high power output while reducing the heat consumption in gas operation almost to its level in Diesel operation. A close look is taken at the design features which distinguish the dual-fuel engine from the 52/55 A Diesel engine, such as the gas supply, injection system and automatic ...

International Nuclear Information System (INIS)

Growing public and political interests towards incorporating passive safety features in nuclear installations, let Siempelkamp in late 1987 propose a solution consisting of a prestressed cast-iron pressure vessel and a passive heat removal system, integrated in the reactor cell surrounding the vessel. This solution combines the inherent safety of a prestressed metallic pressure vessel with the advantages of a passive heat removal system and thus constitutes a major step towards the goal of further reducing potential residual risks. The design had to meet the boundary conditions for reactor core and reactor building of the modular 200 MWth pebble bed reactor of Siemens/-KWU. The engineering design showed that many input parameters needed for the finite-element-analysis of the overall structure required a verification by measurements in a well scaled test setup. This was especially required for the heat transfer from the liner of the prestressed ...

Energy Technology Data Exchange (ETDEWEB)

The need is substantiated for using remote control of technological processes on blowout dangerous beds. A method is proposed for this control based on recording with the help of AGZ apparatus for gas release into the roadway. Distinguishing features are indicated for the change in methane concentration in the roadway with normal occurrence of the process and in the case of blowout of coal and gas.

Energy Technology Data Exchange (ETDEWEB)

The possibility of modifying the functional composition of humic acids by gas-phase ozonation of bed-oxidized brown coal was examined. About 90% of the organic matter of brown coal was converted to low-molecular weight soluble oxygen-containing products by stepwise liquid-phase ozonation (in chloroform and acetic acid).

Energy Technology Data Exchange (ETDEWEB)

Most of the Turkish lignites have undesired fuel properties and they are extremely polluting. In this study, Sweet Sorghum was chosen as the energy plant. Combustion experiments of lignite and lignite-Sweet Sorghum mixtures were carried out in a fluidised bed system. The fuel-feeding ratio was set such that the thermal output of the system remained constant. Addition of Sweet Sorghum to the lignite reduces the pollutant concentration. The results were supported by experimental results.

Energy Technology Data Exchange (ETDEWEB)

Cattle or chicken manure is pelletized, and a bed of the pellets is combusted at the bottom to create a temperature gradient and to generate a fuel gas. Thus, an approximately 25 cm-high bed of approximately 5 mm-diameter chicken manure pellets was combusted to produce a fuel gas of 1622 kcal/kg manure.

Energy Technology Data Exchange (ETDEWEB)

Background and Purpose: Total-body irradiation (TBI) is an important part of the conditioning regimen for hematopoietic stem cell transplantation (HSCT) in patients with hematologic malignancies. The results after treatment with various TBI regimes were compared, and dose-effect relationships for the endpoints relapse incidence, disease-free survival, treatment-related mortality, and overall survival were derived. The aim was to define requirements for an optimal treatment schedule with respect to leukemic cell kill and late normal-tissue morbidity. Material and Methods: A literature search was performed. Three randomized studies, four studies comparing results of two or three TBI regimens, and nine reports with results of one specific TBI regimen were identified. Biologically effective doses (BEDs) were calculated. The results of the randomized studies and the studies comparing results of two or three TBI regimens were pooled, and the pooled relative risk (RR) was ...

UK PubMed Central (United Kingdom)

In the isolated rat mesenteric bed, the 1 min perfusion with 100 nm anandamide, a concentration that did not evoke vasorelaxation, elicited an acute release of 165.1 ± 9.2 pmol nitric...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A gas-fired boiler plant comprises a burner bed extending over a flat surface and heat exchanger pipes arranged above the burner bed, parallel to the said surface. The heat exchanger tubes comprise pipes equipped with a pluraltiy of flat ribs which extend substantially radially from the said pipes and which are provided in space arrangement over the length of the said heat exchanger pipes. The ribs are provided with bent-off portions. The hot flue gases rising from the burner bed flow through the gaps formed between the said ribs and pipes. In order to improve both the convective heat transmission and the utilization of the radiant heat, the bent-over edges are inclined, at least partly, relative to the surface of said burner bed, the arrangement being selected in a manner to ensure that bent-over portions point towards the burner bed and the rising flue gased are guided around the ...

International Nuclear Information System (INIS)

We have investigated the diffusion enhancement mechanism of boron-enhanced diffusion (BED), wherein boron diffusivity is enhanced four to five times over the equilibrium diffusivity at 1050 ampersand hthinsp;degree C in the proximity of a silicon layer containing a high boron concentration. It is demonstrated that BED is driven by excess interstitials injected from the high boron concentration layer during annealing. For evaporated layers, BED is observed above a threshold boron concentration between 1% and 10%, though it appears to be closer to 1% for B-implanted layers. For sub-keV B implants above the threshold, BED dominates over the contribution from transient-enhanced diffusion to junction depth. For 0.5 keV B, this threshold implantation dose lies between 3x10"1"4 and 1x10"1"5 cm"-"2. It is proposed that the excess interstitials responsible for BED are produced during the ...

Energy Technology Data Exchange (ETDEWEB)

Presently, high wind potentials in remote areas may not be utilized for electricity production due to limited grid transmission capacity and/or difficulties in matching the electricity production with the demand. The overall project objective is to help overcome these bottlenecks, i.e. to identify and analyze methods and technologies for making it viable to utilize more of the wind potential in remote areas. The suggestion is to develop a power control concept for wind turbines which will even out the power fluctuations and make it possible to increase the wind energy penetration. The main options are to combine wind power with a pumped hydro power storage or with an AC/DC converter and battery storage. The AC/DC converter can either be an `add-on` type or it can be designed as an integrated part of a variable speed wind turbine. The idea is that combining wind power with the power control concept will make wind power more firm and possible to ...

Energy Technology Data Exchange (ETDEWEB)

Interbedded limestones and dolomites of the Cambrian Conococheague Formation cropping out northwest of Lancaster exhibit contrasting rheological behavior during deformation. Dolomite beds are uncleaved and form concentric F[sub 1] recumbent folds with hinges trending northeast, parallel to the trend of the Appalachian orogen. Limestone beds show subhorizontal S[sub 1] cleavage with southeast-plunging extension lineations defined by fibrous calcite and ubiquitous smear lineations. In limestone beds, intrafolial F[sub 1] folds with curvilinear hinges are sheath folds flattened in the S[sub 1] cleavage. In zones of most intense shear, F[sub 1] hinges parallel the regional northwest directed tectonic transport direction. In 1969, the author attributed the variation in intrafolial F[sub 1] fold-hinge orientation to hinge-parallel buckling due to constrictional bulk strain. This interpretation, however, is not consistent with the ...

Energy Technology Data Exchange (ETDEWEB)

The capacity extension of additives was tested in a 200 cm/sup 2/bi-cell and a Zn powder moving-bed slurry. It was found that for the Type A additives in 12 M KOH, 25 g/l of silicate provided higher capacity than stannate, titanate and aluminate additives. The optimum concentration of sorbitol (a Type B additive that stabilizes polymeric chains involving ZnO) was found to be 15 g/l in 12 M KOH. A silicate and sorbitol combination added to Zn powder slurry in 12 M KOH provided a 20% increase in discharge capacity (195 Ah/l at 200 A/cm/sup 2/) compared to the maximum capacity obtained with silicate alone. A much lower capacity (74 Ah/l) was realized with silicate as Type C additive (precipitation of ZnO away from the Zn surface, for low KOH concentrations). The mechanisms of passivation and capacity extension were discussed and a model presented. The cell voltage and power densities were determined for the discharge process as a function of (a) ...

Energy Technology Data Exchange (ETDEWEB)

Blade fatigue life is an important element in determining the economic viability of the Vertical-Axis Wind Turbine (VAWT). A principal source of blade fatigue is thought to be the stochastic (i.e., random) aerodynamic loads created by atmospheric turbulence. This report describes the theoretical background of the VAWT Stochastic Aerodynamic Loads (VAWT-SAL) computer code, whose purpose is to numerically simulate these random loads, given the rotor geometry, operating conditions, and assumed turbulence properties. A Double-Multiple-Stream Tube (DMST) analysis is employed to model the rotor's aerodynamic response. The analysis includes the effects of Reynolds number variations, different airfoil sections and chord lengths along the blade span, and an empirical model for dynamic stall effects. The mean ambient wind is assumed to have a shear profile which is described by either a power law or a logarithmic variation with height above ground. Superimposed on this is a full 3-D ...

International Nuclear Information System (INIS)

A study was conducted to determine the feasibility and the opportunity of photochemical pretreatment on the biodegradation and detoxification of Methyl Tert Butyl Ether (MTBE), Ethyl Tert Butyl Ether (ETBE) and Tert Amyl Methyl Ether (TAME), the most common oxygenates used as octane enhancers in unleaded gasoline. The production, storage, uses and disposal of oxygenates result in an unknown amount of groundwater pollution. Because of their high solubility, MTBE, ETBE and TAME are detected in large portions in saturated zones of aquifers. The biodegradation of these oxygenates is difficult and slow, and information regarding their biodegradability is scarce. Photo-decomposition of oxidants under appropriate UV radiation has been shown to be very effective because the hydroxyl radicals produced possess high oxidation potential. In this study, the H_2O_2/UV process was used to generate hydroxyl radicals. Maximal oxygenates transformation was obtained in a few minutes. The experiment ...

Energy Technology Data Exchange (ETDEWEB)

Purpose. We have tested a procedure of focal injection of the contrast medium Lipiodol as a fiducial marker for image-guided boost of the tumor in bladder cancer radiotherapy (RT). In this study, we have evaluated the feasibility and the safety of the method as well as the inter- and intra-fraction shift of the bladder tumor. Materials and methods. Five patients with muscle invasive urinary bladder cancer were included in the study. Lipiodol was injected during flexible cystoscopy into the submucosa of the bladder wall at the periphery of the tumor or the post resection tumor-bed. Cone-beam CT (CBCT) scans were acquired daily throughout the course of RT. Results. Lipiodol demarcation of the bladder tumor was feasible and safe with only a minimum of side effects related to the procedure. The Lipiodol spots were visible on CT and CBCT scans for the duration of the RT course. More than half of all the treatment fractions required a geometric shift ...

British Library Electronic Table of Contents (United Kingdom)

The fossil fuel consumption and pollutant emissions in a coal fired fluidized bed boiler could be reduced by biomass pyrolysis gas reburning. The influence of three kinds of biomass pyrolysis gases on the emission of N2O in a laboratory scale fluidized bed was investigated using the mechanism of GRI3.0 in this paper. The results showed that: the effect of sawdust pyrolysis gas reburning on N2O was more significant than that of rice husk and orange peel under the same conditions; the increase of initial oxygen content from 1% to 8% in flue gas would restrain the decomposition of N2O; the N2O decomposition was enhanced by increasing reaction temperature from 1073.15 K to 1323.15 K, and the decomposition rate may reach 99% at 1223.15 K.

Science.gov (United States)

Applying an underfeed system, the underfeed circulating spouted bed was designed as a desulfurization reactor. The main objective of the technology is to improve the mixing effect and distribution uniformity of solid particles, and therefore to advance the desulfurization efficiency and calcium utility. In this article, a series of experimental studies were conducted to investigate the fluidization behavior of the solid-gas two-phase flow in the riser. The results show that the technology can distinctly improve the distribution of gas velocity and particle flux on sections compared with the facefeed style. Analysis of pressure fluctuation signals indicates that the operation parameters have significant influence on the flow field in the reaction bed. The existence of injecting flow near the underfeed nozzle has an evident effect on strengthening the particle mixing.

Science.gov (United States)

Thalassinid shrimp cause significant problems for oyster aquaculture in the Pacific Northwest (USA) where oysters succumb to the physical disruption of the sediment by the burrowing activity of these animals. While electrofishing is a commonly used technique to capture fish and some invertebrates i...

Energy Technology Data Exchange (ETDEWEB)

The gas-solid reaction and breakthrough curves in the fixed-bed reactor are of great importance, and being influenced by a number of factors makes the prediction of these factors a difficult problem. In this study, the reaction rate between solid sorbents and hydrogen chloride gas at high temperature was first investigated. On the basis of a fixed-bed reactor, the experimental results were analyzed by the shrinking core model of diffusion and surface chemical reaction control. The results showed that reaction rates of two sorbents with hydrogen chloride gas were controlled by the combination of the surface chemical reaction and diffusion of product layers, and the reaction rates nearly keep constant within 15 h of the initial reaction period and then decrease gradually. The results of the breakthrough curves show that solid sorbents in the fixed-bed reactor are capable of reducing the HCl level to near-zero levels at ...

UK PubMed Central (United Kingdom)

The juxtacapsular BNST (jcBNST) is activated in response to basolateral amygdala (BLA) inputs through the stria terminalis and projects back to the anterior BLA and to the central nucleus of...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The technology being evaluated is the Modified In-Situ (MIS) retorting process for raw shale oil production, combined with a Circulating Fluidized Bed Combustor (CFBC), for the recovery of energy from the mined shale. (VC)

Science.gov (United States)

The goal of this research project was to determine the eff ects of geometric and mechanical parameters characterizing the soil-structure interaction developed in a buried pipe installation. Parameters such as pipe ring stiff ness, bedding thickness, trenc...

UK PubMed Central (United Kingdom)

In Syrian hamsters (Mesocricetus auratus), the expression of reproductive behavior requires the perception of social odors. The behavioral response to these odors is mediated...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A new method for computing petroleum reserves which takes into account the volumetric elasticity of stratal petroleum and a porous medium of a collector is examined based on the example of developing petroleum beds of Cretaceous horizon of the Groznenskiy region.

Energy Technology Data Exchange (ETDEWEB)

This purpose of this report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period April 1, 2005 through June 30, 2005. The following tasks have been completed. First, the new Combustion Laboratory was occupied on June 15, 2005, and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building is in the final painting stage. Second, the fabrication and manufacturing contract for the CFBC Facility was awarded to Sterling Boiler & Mechanical, Inc. of Evansville, Indiana. Sterling is manufacturing the assembly and component parts of the CFBC system. The erection of the CFBC system is expected to start September 1, 2005. Third, mercury emissions from the cofiring of coal and chicken waste was studied experimentally in the laboratory-scale simulated ...

UK PubMed Central (United Kingdom)

The sensitivities to cefuroxime and cephradine of potentially pathogenic bacteria isolated in two British general hospitals comprising 900 beds have been assessed. In a three-month period 2537 strains...Full Text Available

UK PubMed Central (United Kingdom)

Most hospitals today are quickly developing special programs and services that are designed to compete for physicians and patients, and ultimately fill unoccupied beds. In an attempt to attract physicians...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Describes the wastes produced and the waste disposal methods used at BEWAG power plants. Wastes covered include fly ash, fluidized bed ash, gypsum from flue gas desulfurization and evaporation residues. Disposal methods include using ashes and gypsum to make building materials. Despite many years of experience in the utilization and disposal of residues from coal-fired power stations BEWAG have not encountered any disposal problems. 5 tabs.

International Nuclear Information System (INIS)

Three dimensional temperature field and helium flow field of TBM are simulated using the general purpose computational fluid dynamics (CFD) code FLUENT. The temperature distribution of Be Armor, Be Pebble Bed, Li_4SiO_4 Pebble Bed, Structure Material of TBM, and helium flow field in the cooling pipe are presented. The research indicates that the work temperature of each material is under the material temperature allowed except some places where high temperature should be excluded in the design. The results will provide references for further optimized thermal hydraulic design of ITER China TBM. (authors)

International Nuclear Information System (INIS)

The technology of nuclear direct propulsion orbit transfer systems based on the Particle Bed Reactor (PBR) is described. A 200 megawatt illustrative design is presented for LEO to GEO and other high #DELTA#V missions. The PBR-NOTV can be used in a one-way mode with the shuttle or an expendable launch vehicle, e.g., the Titan 34D7, or as a two-way reusable space tug. In the one-way mode, payload capacity is almost three times greater than that of chemical OTV's. PBR technology status is described and development needs outlined.

Energy Technology Data Exchange (ETDEWEB)

The author presents a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of CO{sub 2} in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The predicted efflux of CO{sub 2} from a canister containing LiOH compared favorably with measured values reported elsewhere. It was determined from a computational study that the time for breakthrough of CO{sub 2} at a prescribed level is nearly directly proportional to bed length and inversely proportional to gas flow and porosity.

Science.gov (United States)

No research has compared expressions of weight bias across different subgroups of obese individuals. This study compared attitudes toward and beliefs about obesity in women with and without binge eating disorder (BED) and examined whether these attitudes are related to psychological factors. Fifty obese women with BED were compared with an age- and body mass index (BMI)-matched group of 50 obese women without BED on a battery of established measures of anti-fat attitudes and beliefs about weight controllability and psychological factors (self-esteem, depression, and eating disorder features). The ageand BMI-matched groups did not differ with respect to beliefs about obesity or attitudes toward obese persons, or in self-esteem or depression. Correlational analyses conducted separately within each group revealed that women with BED who reported more favorable attitudes towards obese persons had higher ...

Energy Technology Data Exchange (ETDEWEB)

The objectives of this program are to evaluate the Coal Fired Combined Cycle (CFCC) power plant conceptual design and to conduct supporting development programs for pressurized fluidized bed technology advancement in combustion/steam generator, gas turbine and hot gas cleanup technologies. The Coal-Fired Combined Cycle is the unique power plant concept developed under the leadership of the General Electric Company to provide a direct coal-burning gas turbine and steam turbine combined-cycle power plant. The advantages of the combined cycle for higher efficiency and the potential of the pressurized fluidized bed combustor improvements in emissions could offer a new and attractive option to the electric utility industry. The CFCC approach provides for cooling the fluid bed combustor through the use of steam tubes in the bed which supply a steam turbine generator. The partially cooled combustion gases ...

CERN Multimedia

Test de levage module QRL

International Nuclear Information System (INIS)

Short communication.

CERN Document Server

Metals and alloys : atmospheric corrosion testing : General requirements for field tests

Energy Technology Data Exchange (ETDEWEB)

A three-dimensional mathematical model has been developed as a tool for furnace structure design and operation conditions optimization when the straw combustion is in oxygen-enriched or conventional air atmospheres. Mathematical methods have been used based on a combination of FLIC (A fluid Dynamic Incinerator Code) code for the in-bed incineration and commercial software FLUENT for the over-bed combustion. Oxygen-enriched atmospheres promote the destruction of most pollutants due to the high oxygen partial pressures and temperatures, which is reflected by very low residual amounts of organic combustion by-products in the bottom ash and flue gas of the straw-fired boiler unit. The predictions indicated that the maximum combustion temperature is around 1500 K, CO emission is 201 vppm and O{sub 2} concentration is about 6.9 vol% at furnace exit, and it is shown that mathematical models can serve as a reliable tool for detailed analysis of straw ...

International Nuclear Information System (INIS)

Functionalizing nanoparticle surfaces is essential for achieving homogeneous dispersions of monodisperse particles in polymer nanocomposites for successful utilization in engineering applications. Functionalization reduces the surface energy of the nanoparticles, thereby limiting the tendency to agglomerate. Moreover, reactive groups on the surface can also participate in the polymerization, creating covalent bonds between the inorganic and organic phases. In this paper, a fluidized bed inductively coupled plasma (FB-ICP) reactor is used to break apart the agglomerates and functionalize commercial TiO2 nanoparticle powders in a batch of several grams. The fluidized bed could be implemented into a continuous flow reactor, potentially making this a viable method to treat larger quantities of commercial powders. The particles are treated with acrylic acid (AA) and tetraethylorthosilicate (TEOS) plasma and the functionalized particles were ...

Energy Technology Data Exchange (ETDEWEB)

The growth kinetics constants and concentration of active attached biomass in an anaerobic fluidized bed which decomposes acetic, propionic and butyric acid were estimated. The mixture of above mentioned fatty acids was supplied to the fluidized bed in the range of hydraulic retention time (HRT) from 0.25 to 2 days. After the effluent reached in a steady state in quality, batch experiments were conducted separately with each fatty acid as a substrate in order to investigate the decomposition characteristics of each substrate by attached biomass. In order to estimate the parameter values of the growth kinetics of the bacteria, batch experiments were also conducted under the completely mixed condition using detached biomass from a support material. The changes of fatty acid concentrations with time were clearly expressed with the Monod growth model. Maximum specific substrate decomposition rates and saturation constants, and active biomass ...

Energy Technology Data Exchange (ETDEWEB)

This study aims to develop a particulate model combining solid waste particle combustion and heavy metal vaporization from burning particles during MSW incineration in a fluidized bed. The original approach for this model combines an asymptotic combustion model for the carbonaceous solid combustion and a shrinking core model to describe the heavy metal vaporization. A parametric study is presented. The global metal vaporization process is strongly influenced by temperature. Internal mass transfer controls the metal vaporization rate at low temperatures. At high temperatures, the chemical reactions associated with particle combustion control the metal vaporization rate. A comparison between the simulation results and experimental data obtained with a laboratory-scale fluid bed incinerator and Cd-spiked particles shows that the heavy metal vaporization is correctly predicted by the model. The predictions are better at higher temperatures because ...

Science.gov (United States)

The present study numerically investigates the enhancement of forced convective heat transfer from a single circular cylinder embedded in a packed bed of spherical particles confined by two impermeable parallel plates. The heat transfer results from the heated cylinder, with and without the presence of a porous medium, are compared. The results show that the presence of the porous particles enhances the heat transfer from the cylinder; however, the significant heat transfer augmentation is produced at high Re due to the effect of thermal dispersion. In addition, the effect of Re on Nut is much greater than that of kr and Bi in the porous channel. It is also found that the %?p is much higher than %HTE producing from packing the empty channel.

British Library Electronic Table of Contents (United Kingdom)

The design of solid breeder blankets is strongly affected by the low values of thermal conductivity and density of ceramic breeder pebble beds. A significant rise of both quantities would enhance the thermal performance and lead to an increased tritium breeding ratio. In order to improve these quantities pretreated lithium orthosilicate pebble material was dry pressed and subsequently sintered. The thermal conductivity of cylindrical pellets was determined by the heat pulse method using a laser flash device. A pebble bed characteristic sample was also investigated in order to check the measurement accuracy in comparison with previous results. Furthermore, two samples of low density cellular ceramics were also prepared by infiltration of polymer foams with a ceramic slurry. The thermal cond...

Energy Technology Data Exchange (ETDEWEB)

Sasol, a South-African company, has converted coal into synthetic fuels for 40 years; in order to increase by 6 pc its annual production (40 Mt coal are processed), Sasol has launched the Sky High project and intends to replace the ancient Sasol Synthol reactors by Advanced Synthol reactors using conventional fluidized beds instead of circulating fluidized beds. Coal is first gasified under high pressure and high temperature conditions (the Secunda site uses the Fischer-Tropsch conversion process) and is then processed in the reactor through a single phase process using an iron-base catalyst, leading to significant cost reductions.

Science.gov (United States)

In this paper Particle Bed Reactor (PBR) designs are discussed which use /sup 233/U and /sup 242m/Am as fissile materials. A constant total power of 100MW is assumed for all reactors in this study. Three broad aspects of these reactors is discussed. First, possible reactor designs are developed, second physics calculations are outlined and discussed and third mass estimates of the various candidates reactors are made. It is concluded that reactors with a specific mass of 1 kg/MW can be envisioned of /sup 233/U is used and approximately a quarter of this value can be achieved if /sup 242m/Am is used. If this power level is increased by increasing the power density lower specific mass values are achievable. The limit will be determined by uncertainties in the thermal-hydraulic analysis. 5 refs., 5 figs., 6 tabs.

Energy Technology Data Exchange (ETDEWEB)

Formulas were developed based on an aqueous solution of hydrolyzed polyacrylonitrile widely used in the oil industry. The additive used consisted of products of industrial production: synthetic resin TEG-1 with hardening agent PEPA (polyehtylene polyamine) and technical formalin. The mixtures containing about 80-85% by volume 5% hydrolyzed polyacrylonitrile, 10-15% by volume of resin TEG-1 with hardening agent PEPA and 3-5% by volume formalin satisfy the requirements made for the plugging materials. The initial mixtures are distinguished by technological efficiency of preparation and have controllable hardening periods. Physical-chemical properties are given for the gel polymers. In the set of properties, the mixtures based on hydrolyzed polyacrylonitrile, resin TEG-1 with hardening agent PEPA and formalin can be recommended as plugging materials of temporary action with complex treatment of the heterogeneous beds.

Energy Technology Data Exchange (ETDEWEB)

An emergency shutdown system for high-temperature gas-cooled pebble-bed reactors is proposed in addition to the common absorber rod shutdown system. This system is based on the strongly absorbing effect of small boronated graphite spheres (called KLAK), which trickle in case of emergency by gravity from the top reflector into the reactor core. The inner reflector of the Siemens-Argonaut reactor was substituted by an assembly of spherical Arbeitsgemeinschaft Versuchsreaktor fuel elements, and the shutdown effect was examined by installing well-defined KLAK nests inside this assembly. The purpose was to develop and prove a calculational procedure for determining criticality values for assemblies of large fuel spheres and small absorbing spheres.

Energy Technology Data Exchange (ETDEWEB)

Co-combustion of chicken litter with coal was performed in a laboratory-scale fluidized bed combustor to investigate the effect of chicken litter addition on the partitioning behavior of mercury. Gaseous total and elemental mercury concentrations in the flue gas were measured online, and ash was analyzed for particle-bound mercury along with other elemental and surface properties. The mercury mass balance was between 85 and 105%. The experimental results show that co-combustion of chicken litter decreases the amount of elemental and total mercury in the gas phase. Mercury content in fly ash increases with an increasing chicken litter share. 22 refs., 6 figs., 5 tabs.

Energy Technology Data Exchange (ETDEWEB)

A numerical model for the development of bed dominated scour around sub-sea structures is presented. The hydrodynamic part of the model is based on a modified potential flow theory. The purpose of the present study has been to develop relatively simple models, yet complex enough to capture the main physics that can be used as engineering tools. An overview of scour phenomena and the basic problems of scour in steady current flow is presented. A hydrodynamic model for horseshoe vortex is presented, as well as a model for the bed transport, and examples are given. The scour in oscillatory flow and a curvilinear model for suspended sediment calculations are described. An advection-diffusion model (formulated in a curvilinear stretched coordinate system) has been developed and is described in an article which has been submitted for publication, a copy of the article is enclosed in Appendix E of the report. (EG)

Energy Technology Data Exchange (ETDEWEB)

The moment analysis of pulse responses was applied to a biological activated carbon (BAC) bed to evaluate the microbial activity. Glucose and activated carbon fiber (ACF) were employed in experiments as a model tracer and an activated carbon respectively. No significant difference in biodegradation rates of glucose by microorganisms attached on different solid supports such as activated carbon inactivated carbon and glass fibers was observed. However, higher microbial activity was obtained from microorganisms supported on the ACF in terms of the apparent degradation of total organic including metabolic byproducts by microorganisms, since part of the metabolic byproducts was irreversibly deposited onto the ACF. 11 refs., 6 figs.

Energy Technology Data Exchange (ETDEWEB)

Both the KRW fluidized-bed gasifier and the transport gasifier case studies were used for this assessment. The transport technology is a high-velocity circulating fluidized-bed reactor currently under development by The M.W. Kellogg Company. In the earlier assessment, seven design concepts or cases were identified; a process design was developed; major equipment items were identified; estimates of capital cost, operation and maintenance cost, and cost of electricity were developed; reliability was predicted; and development issues were identified for six studies. Three of the most probable cases were further evaluated for a Greenfield assessment in this report to adequately determine all costs independent of facilities at Plant Wansley.

British Library Electronic Table of Contents (United Kingdom)

Abstract Aims: To develop an in vitro flat-bed perfusion biofilm model that could be used to determine the antimicrobial efficacy of topically applied treatments. Methods and Results: Pseudomonas aeruginosa and Staphylococcus aureus biofilms were grown within continuously perfused cellulose matrices. Enumeration of the biofilm density and eluate was performed at various sampling times, enabling determination of the biofilm growth rate. Two antimicrobial wound dressings were applied to the surface of mature biofilms and periodically sampled. To enable real-time imaging of biofilm growth and potential antimicrobial kinetics, a bioluminescent Ps. aeruginosa biofilm was monitored using low-light photometry. Target species produced reproducible steady-state biofilms at a density of c. 107 per b...

Energy Technology Data Exchange (ETDEWEB)

The present invention provides an improvement in the art of combined steam turbine and gas turbine power plants of the type wherein the principal source of energy is a fluidized bed combustor fueled by coal. More specifically, the invention pertains to supplemental firing of the gas turbine cycle with a clean hydrocarbon fuel (CHF) at a high incremental efficiency to significantly increase overall plant efficiency.

Science.gov (United States)

A steam producing system based on fluidized-bed gasification of biomass materials is discussed. Limited experimental results are discussed and show that steam has been produced at rates of 334.3 kg/hr. (737 lbs/hr.) with 2.8 kg of stream produced for each kilogram of cotton gin trash (2.8 lb/lb.). ref.

Energy Technology Data Exchange (ETDEWEB)

A final report is presented on the design, environmental characteristics, performance and maintainability, and economic analysis of a commercial 663 MWe coal-fired combined cycle power plant using pressurized fluidized bed combustion, and advanced technology in the hot gas cleanup system and gas turbines. Experimental data on the performance of each of the major components are included. (LCL)

Wastenet

... Piled foundations were adopted and precast concrete piles 6 - 8 m long were driven through the alluvial soils onto a solid bed rock. Special precautions were taken to ensure vibrations did not affect an adjacent apartment block. 88 piles were driven in 2 working days. Navigation - Home - Services - Previous projects - Contact Us - Philosophy - About us - Water Slides - Links ...

Energy Technology Data Exchange (ETDEWEB)

General conclusions, principles and order of substantiating the extractable reserves and coefficients of oil extraction from oil and oil and gas fields are presented. Recommendations are made for solving questions of constructing calculation models for heterogeneous beds, schematization of the working conditions, selection of mathematical models for oil extraction for different geological-field conditions and different stages of ''life'' of the field.

International Nuclear Information System (INIS)

This paper presents a brief overview of refuse derived fuel (RDF) processing systems, and the different types of RDF. The quality of RDF, combustion of RDF in fluidized beds, and moving grate reactors, operating conditions, emissions (sulphur dioxide, nitrogen oxides, carbon monoxide and hydrogen chloride) and thermal efficiency are discussed. (UK).

Energy Technology Data Exchange (ETDEWEB)

Restructuring was carried out on a sedimentary basin structure model of the Osaka plain including Osaka Bay by using newly obtained underground structural data. After the Hygoken-nanbu Earthquake of 1995, a large number of underground structure investigations have been performed in Osaka Bay and urban areas of Kobe and Osaka. However, very few surveys have been done in areas peripheral to Osaka Prefecture, such as the Ikoma area. Therefore, an attempt has been made to increase the number of measuring points to acquire underground structural data of these areas. Estimation of basic rock depths has utilized the dominant cycles in H/V spectra obtained from micro vibration survey, and good correlation of the base rock depths derived by a refraction exploration and a deep-bed boring investigation. With regard to bed division and P- and S- wave velocities in sedimentary beds in the Osaka sedimentary basin, an underground ...

Energy Technology Data Exchange (ETDEWEB)

The use of pressurised fluidized-bed coal combustion (fbc) in a combined cycle is seen as a most attractive technology for increasing the efficiency of electricity generation. The concept of pressurised fbc is described and the technical problems that are encountered in its operation and in limiting it to a gas turbine are discussed. Details are given of pilot plant facilities and current R and D programmes.

Energy Technology Data Exchange (ETDEWEB)

This report describes work carried out in the context of TurboTech Interim for the development of a system for monitoring stationary gas turbines for approaching the stability limit of the compressor. The requirements for the system components were defined and the suitability of different types and positions of pressure sensors were examined and evaluated. It was found very early in the work that, due to the complexity of the object being monitored, one would not succeed in finding a simple criterion for monitoring the pump limit. Rather, apart from the selection of suitable sensors and optimum positions, one must analyse the present signals in different ways and create a decision matrix from this. Existing work on this subject is mostly concerned with the phenomena in the context of experiments on experimental compressors or is not suitable for the requirements of stationary industrial gas turbines. The project is being carried out in the context of TurboTech II with the main aims of: ...

Science.gov (United States)

The procedure describes the procedures to be used in evaluating consumable and combustible cartridge cases. Included are ballistic tests, environmental tests, adverse condition tests, fungus resistance tests, drop tests and safety tests. (Author)

International Nuclear Information System (INIS)

... cadmium sulfides communications electrons performance testing physical

Science.gov (United States)

Breath Tests; Human Volunteers; Pilot Study

Energy Technology Data Exchange (ETDEWEB)

In the research of a more efficient, less costly, more environmentally responsible and less technically difficult method for generating electrical power from coal, `the Partially Gasified Coal Fired Combined Cycle with a CFBC with Different Speeds (DFBC)` is introduced by Tsinghua University. The high efficiency cycle includes gasification, compressed air heating in a fluidized bed immersed air heater followed by a combustor and the heat recovery of gas turbine exhausted gas used as the combustion of coal in the differential-velocity atmospheric circulating fluidized bed. Superheated steam is raised in the DFBC boiler. A preliminary analysis is made for the choice of combined cycle components. The computer program can be used to evaluate the design and off-design performance of the power plant. The simulation results show that the new system is a valuable coal fired combined cycle system for China, mainly to the improvement of the existing ...

International Nuclear Information System (INIS)

The nuclear power industry has experienced four carbon based adsorbent fires in its history, one was of the Monticello Standby Gas Treatment System and other three were in various off-gas delay beds. Although, some of the latter may not be classified as a full fledged fires. There were a number of experiments performed relating to igniting carbon beds and experiments relating to attempts at extinguishing set fires reported in the literature. Review of these experiments indicates that fire resulting from decay heat of adsorbed radioactive iodine is not justified even under the somewhat unrealistic source terms still in effect. At the same time the non-nuclear chemical industry application of carbon base adsorbents for solvent recovery has resulted in numerous fires and significant property losses. Fire control systems installed in nuclear air cleaning systems in the US consists of water deluge. Accidental initiation of these systems has occurred ...

International Nuclear Information System (INIS)

When a nuclear power station was installed on the Meuse in central Belgium, the impact of thermal, radioactive, and chemical waste on the water of the Neuse and on its biocenoses was studied. Three successive periods of development of the channel bed and the flood plain in Belgium have occurred, and their hydrological, physicochemical, and ecological consequences have been examined. Since the last century, the ecosystem of the Meuse has undergone, due to the increasing activity of man, modifications of increasing importance: marked reduction of the water flow, a drastic increase in the suspended material being transported, a degree of eutrophication of the water, and the disturbance of the original floral and faunal communities. The causes of this evolution of the Meuse can be itemized as different types of human interference in descending order of importance: (1) occupation of the catchment area; (2) encroachment on the flood plain; (3) encroachment on the channel ...

Energy Technology Data Exchange (ETDEWEB)

In order to establish coal NOx preventive measures, discussions were given on formation of N2 in the fixed-bed pyrolysis of low rank coals and the mechanisms thereof. Chinese ZN coal and German RB coal were used for the discussions. Both coals do not produce N2 at 600{degree}C, and the main product is volatile nitrogen. Conversion into N2 does not depend on heating rates, but increases linearly with increasing temperature, and reaches 65% to 70% at 1200{degree}C. In contrast, char nitrogen decreases linearly with the temperature. More specifically, these phenomena suggest that the char nitrogen or its precursor is the major supply source of N2. When mineral substances are removed by using hydrochloric acid, their catalytic action is lost, and conversion into N2 decreases remarkably. Iron existing in ion-exchanged condition in low-rank coal is reduced and finely diffused into metallic iron particles. The particles react with heterocyclic nitrogen compounds and turn ...

Energy Technology Data Exchange (ETDEWEB)

Devolatilization, char combustion and emission characteristics of different single fuel particles were studied under various fluidized bed combustor conditions, in order to develop a classification system which enables prediction of the behaviour of different fuels ranging from fixed carbon rich coals to volatile rich woods and plastics. To investigate formation reaction, the concentration of CO, CO{sub 2}, total hydrocarbons, O{sub 2}, NO and N{sub 2}O were measured continuously. Additionally, temperature histories of the particles were recorded by implanting thermocouples. Devolatilization and char combustion were analysed by an integral and differential method. The integral analysis uses global rates which were compared with the ultimate and proximate analyses and used to classify the fuels. In the differential analysis the single physical and chemical steps viz mass transfer from the bulk gas to the particle surface, mass transfer through the ash layer and ...

Energy Technology Data Exchange (ETDEWEB)

Wastewater from a food-manufacturing plant with a low concentration of organic matter was treated at 37 centigrade in an anaerobic fluidized-bed reactor or in an upflow anaerobic sludge blanket. As the influent TOC (total organic carbon) concentration decreased, the TOC removal efficiency in these reactors decreased from 85% to 65%. The concentration of suspended solids in the effluent could be reduced to 20 mg/l, which corresponded to 7% of that in the influent. The effluent from both reactors was treated aerobically in a fixed-bed reactor. The TOC concentration and optical density of effluent from the aerobic treatment were reduced to 5 mg/l and 0.005, respectively. When the effluent treated anaerobically or aerobically was passed over an activated carbon column, the effluent TOC concentration was reduced to 2 to 3 mg/l. The conductivity in raw wastewater was remarkably reduced on an ion-exchange resin column. Ultra-pure water for industrial ...

Science.gov (United States)

The magnetically fluidized bed (MFB) was used as the reactor in a novel semidry flue gas desulfurization (FGD) process to achieve high desulfurization efficiency. Experiments in a laboratory-scale apparatus were conducted to reveal the effects of approach to adiabatic saturation temperature, Ca/S molar ratio and applied magnetic field intensity on SO(2) removal. Results showed that SO(2) removal efficiency can be obviously enhanced by decreasing approach to adiabatic saturation temperature, increasing Ca/S molar ratio, or increasing applied magnetic field intensity. At a magnetic field intensity of 300Oe and a Ca/S molar ratio of 1.0, the desulfurization efficiency (excluding desulfurization efficiency in the fabric filter) was over 80%, while spent sorbent appeared in the form of dry powder. With the SEM, XRD and EDX research, it can be found that the increase of DC magnetic field intensity can make the surface morphology on the surface of the ferromagnetic ...

Energy Technology Data Exchange (ETDEWEB)

A divergence correction is conventionally applied to zero-offset data in an effort to preserved amplitude information. The conventional divergence correction compensates for the geometrical spreading of a point source in a horizontally layered medium where velocity varies with depth only. The dip-dependent divergence correction extends the conventional correction for improved amplitude processing of dipping beds. The dip-dependent divergence correction is computed by dynamic ray tracing, and applied to stacked data using a dip decomposition technique. This correction decreases amplitudes relative to the conventional correction for steep dips and late times. In a data example from the Gulf of Mexico, the conventional correction over- amplified the reflection off a salt dome flank by a factor of 1.6. High amplitudes near salt flanks are also associated with the presence of hydrocarbons. Applying the dip-dependent divergence correction ensures that ``bright spots`` ...

Energy Technology Data Exchange (ETDEWEB)

The Coalspur Formation is a continental succession of interbedded mudstone, siltstone and fine grained sandstone with subordinate coarser grained sandstone layers and channel lag deposits. Chert-pebble conglomerate (the Entrance conglomerate) occurs at the base of the formation, and coal beds interbedded with coaly shale and numerous thin bentonites occur in the upper part of the formation. An economically significant amount of high-quality thermal coal occurs within the upper, Paleocene part of the formation named the Coalspur coal zone. Coal from this zone, also known as the Coal Valley coal zone is being exploited in the Coal Valley Mine. 17 refs., 4 figs.

International Nuclear Information System (INIS)

High-pressure waterjet equipment is now technically and economically viable and commercially available for the following mining and construction applications: (1) drilling soft to medium-hard rock; (2) slotting, discing, chambering, and reaming in all types of rock. However, additional field experience is needed to prepare detailed economic evaluations. Extensive development of new explosives techniques and blasting methods will be required to take full advantage of the unique waterjet hole slotting, discing, and chambering capabilities.

Energy Technology Data Exchange (ETDEWEB)

In most industrial processes operating at elevated temperatures, protective oxide layers perform a vital duty in protecting the underlying metallic alloys from process gases. Coal-fired combined cycle power generation systems present a number of process conditions in which the properties of the protective oxide layers are particularly important. This paper discusses two of these particular conditions: (1) `erosion/corrosion` of in-bed heat exchanger tubing and (2) thermal cycling of hot gas path components. For both these situations, the desirable properties of protective scales are outlined. The behaviour of scales in practice are highlighted. 33 refs., 6 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

To expand the information base on molecular accessibility in solvent swelled coal, Argonne Premium Coal Samples (APCS) were swelled in polar, basic solvents before and after moisture loss and upon air oxidation. So far studies have been reported on the changes in pore size distribution as a function of temperature when polar basic swelling solvents are used. Additional studies employing EPR spin probe techniques performed on the breaking up of the hydrogen bonding between bedding planes were later confirmed by magnetic resonance imaging at Argonne National Lab and the University of Illinois.

Energy Technology Data Exchange (ETDEWEB)

The integration of a gas turbine into a new type of coal-fired combined cycle power plant necessitates a multiplicity of far-reaching changes compared with a normal design. The extremely high pre-heating temperature of the air emanating from the heat exchanger of the fluidized bed for the gas turbine combustion chamber has necessitated extensive development work and associated combustion trials. It was possible for these results to influence the design of the burners whereas the manufacture of other components which was on the critical path was already far advanced.

Energy Technology Data Exchange (ETDEWEB)

In the well-known devices for increasing the decontamination factor in the treatment of radioactive waste water by evaporation, which consist of narrowing devices with evaporator sump and condenser, droplets of liquid and solid particles are carried over from the breeder space, which are radioactive and therefore make the decontamination factor worse. Better results are obtained if one places a fibre bed filter between the evaporator sump and the condenser, preferably in a horizontal connecting pipe between the evaporator sump and the condenser.

Energy Technology Data Exchange (ETDEWEB)

This article describes innovations in new-boiler startups, based on experiences at United Development Group`s 50-MW Niagra cogeneration facility, Niagra Falls, NY. The plant comprises: a circulating coal fluidized bed boiler supplying steam to a nearby factory and electricity to the grid. Before operation the system was flushed with demineralized water, and the boiler degreased, the steam blow relied on a new procedure involving a continuous flow of steam. Startup was then initiated, following manufacturers heatup rate and soak times closely. After startup boiler tube sections were checked, and cleaned if necessary. 1 fig.

International Nuclear Information System (INIS)

Visualizations by real-time neutron radiography are demonstrated of various flow patterns of nitrogen gas-water two-phase flow in a stainless-steel tube, water inverted annular flow in a stainless-steel tube, flashing flow in an aluminium nozzle and fluidized bed in aluminium tube and vessels. Photographs every 1/60 s are presented by an image processing method to show the dynamic behaviours of the various flow patterns. It is shown that this visualization method can be applied efficiently to multiphase flow researches and will be applicable to multiphase flows in industrial machines. (author).

Energy Technology Data Exchange (ETDEWEB)

The presented paper describes the formulation of the fractional mass balances which are used to calculate the concentration and size distribution of char in the balance cells of a circulating fluidized bed boiler. In case of using the shrinking core model additionally the distribution of conversion of the char particles is calculated. Basically two reaction models (a shrinking particle and a shrinking core model) are available to describe the combustion process. The model considers all essential physico/chemical phenomena (primary fragmentation, attrition, mass transfer to gas phase) which have to be taken into account for the description of the combustion process. The model is part of an overall simulation program for circulating fluidized bed boilers. This engineering simulator has been developed to return the main performance parameters of such systems like temperature along the furnace height, size distribution of balanced solid components, ...

Energy Technology Data Exchange (ETDEWEB)

Approximately 700m of deep water clastic deposits of Mt. Messenger Formation are superbly exposed along the Taranaki coast of North Island, New Zealand. Biostratigraphy indicates the interval was deposited during the time span 10.5-9.2m.y. in water depths grading upward from lower bathyal to middle-upper bathyal. This interval is considered part of a 3rd order depositional sequence deposited under conditions of fluctuating relative sea-level, concomitant with high sedimentation rates. Several 4th order depositional sequences, reflecting successive sea-level falls, are recognized within the interval. Sequence boundaries display a range of erosive morphologies from metre-wide canyons to scours several hundred metres across. All components of a generic lowstand systems tract--basin floor fan, channel-levee complex and progading complex--are present in logical and temporal order. They are repetitive through the interval, with the relatively shallower-water components becoming more ...

Energy Technology Data Exchange (ETDEWEB)

CeO{sub 2}-TiO{sub 2} catalysts are prepared by coprecipitation method, and the activity and stability in the catalytic wet air oxidation (CWAO) of phenol are investigated in a batch reactor and packed-bed reactor. CeO{sub 2}-TiO{sub 2} mixed oxides show the higher activity than pure CeO{sub 2} and TiO{sub 2}, and CeO{sub 2}-TiO{sub 2} 1/1 catalyst displays the highest activity in the CWAO of phenol. In a batch reactor, COD and TOC removals are about 100% and 77% after 120 min in the CWAO of phenol over CeO{sub 2}-TiO{sub 2} 1/1 catalyst at reaction temperature of 150 {sup o}C, the total pressure of 3 MPa, phenol concentration of 1000 mg/L, and catalyst dosage of 4 g/L. In a packed-bed reactor using CeO{sub 2}-TiO{sub 2} 1/1 particle catalyst, over 91% COD and 80% TOC removals are obtained at the reaction temperature of 140 {sup o}C, the air total pressure of 3.5 MPa, the phenol concentration of 1000 mg/L for 100 h continue reaction. Leaching ...

International Nuclear Information System (INIS)

The author describes the results of post-test analyses of PANDA transient (M-series) tests M2 and M3. The purpose of the PANDA post-test analysis activity is to demonstrate that TRACG is applicable for the calculation of long-term SBWR containment response to a LOCA. Comparisons between TRACG predictions and test measurements are presented and discussed in the dual context of what the test results show and the capability of TRACG to predict their key features

Energy Technology Data Exchange (ETDEWEB)

Two accelerated aging test procedures are proposed for use on solid dielectric extruded distribution cables under wet conditions. One test method is a fixed time duration test in which the degree of cable specimen aging is assessed in terms of breakdown tests, while the other test method is a time to breakdown test in which the cable specimens are voltage stressed until failure ensues.

Wastenet

Performance testing and ...Performance testing and commissioning In either an Authority-owned or a dedicated MRF, the Contracting Authority should ...Performance testing is done to demonstrate that the contractor is able to meet the guarantees given

Science.gov (United States)

... Construction, Geology, and Aquifer Testing of the Maalo ... 8-98) Prescribed by ANSI Std Z39-18 Page 3. Construction, Geology, and Aquifer Testing ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper describes a radiation shield verification survey of a large hot cell at the Fast Flux Test Facility (FFTF). The following aspects of the shield test are discussed: description of the FFTF; description of the hot cell; the test procedures; radiation protection, and the test results.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

UK PubMed Central (United Kingdom)

IntroductionChest pain with ST-segment elevation is a rare clinical problem during dobutamine stress testing. Although beta-agonists treatment prior to dobutamine stress testing...Full Text Available

DEFF Research Database (Denmark)

GB:Abstract

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Sunflower power conversion system development test program

Science.gov (United States)

This study tested the prediction, derived from the goal-setting hypothesis, that the facilitating

Science.gov (United States)

... Accession Number : ADD318302. Title : ELECTROMAGNETIC MATERIALS TESTING USING RL AND RC-MULTIVIBRATORS. Corporate Author : ...

Science.gov (United States)

... solid particle contamination. Solid particulate impact is a good mechanism for surface heat transfer augmentation. The aug ...

International Nuclear Information System (INIS)

A numerical and experimental investigation is carried out in a solar thermochemical reactor for the thermal dissociation of ZnO at 2000 K using concentrated solar energy. The reactor consists of a cavity-receiver lined with ZnO particles and directly exposed to high-flux irradiation. A transient heat transfer model is formulated to link the rate of radiation, convection, and conduction heat transfer to the reaction kinetics. The radiosity and Monte Carlo methods are applied to obtain the distribution of net radiative fluxes at the internal surfaces of the reactor cavity and at the surface of the ZnO bed. Validation is accomplished in terms of the calculated and measured transient temperature profiles and chemical reaction rates.

Energy Technology Data Exchange (ETDEWEB)

The ElectroStatic Precipitator (ESP) removes dust and tar droplets very efficiently from biomass product gas. Dust was removed for more than 99%. The tar dewpoint was reduced from 130C to 21C, which is sufficient for the application of the product gas in a gas engine. Tar removal is not sensitive to the voltage or fluctuations in the gas residence time . The voltage was varied between 28 to 37 kV{sub arith} and the gas residence time between 4 and 11s. Fouling of the ESP collector plates was negligible, which was concluded from visual inspection after 200 hours of operation. A reduction in the residence time reduces the size of the ESP and has a significant impact on the investment costs of the ESP. Keywords: electrostatic filter, tar removal, circulating fluidised bed (CFB)

British Library Electronic Table of Contents (United Kingdom)

Abstract Capillary permeability is a tightly regulated feature of microcirculation in all organ beds. In sepsis, this feature is fundamentally altered. We have previously reported elevated levels of angiopoietin-2 in patients with septic shock, and have investigated tumor necrosis factor (TNF)-related and weak inducer of apoptosis (TWEAK), which mediates both angiogenesis and inflammation, in those patients. Enzyme-linked immunoassay was used to measure serum TWEAK levels in 20 patients with septic shock, all of whom were treated by direct hemoperfusion with a polymyxin B-immobilized fiber column (DHP-PMX), and in 20 non-septic controls. The TWEAK levels were higher in patients with septic shock (192.8--230.5-pg/mL) than in controls (84.1--28.7-pg/mL, P-=-0.043). Between 11 survivors and 1...

British Library Electronic Table of Contents (United Kingdom)

Feasibility of using fixed bed column of conventional ion exchangers/sorbent and chemical precipitation based processes have been examined for the effective removal of the very low levels of 106Ru activity from NH4NO3 effluent generated during wet processing of rejected sintered depleted uranium fuel pellets. Based on the results, a simple process involving precipitation of cobalt sulphide along with ferric hydroxide was selected and further optimization of process variables was carried out. The optimized process has been found to be highly efficient in reducing 106Ru activity down to extremely low levels.

British Library Electronic Table of Contents (United Kingdom)

Retaining an appropriate level of moisture at the interface between a healing wound and an applied dressing is considered to be critical for effective wound healing. Failure to control exudate at this interface can result in maceration or drying out of the wound surface. The ability to control moisture balance at the wound interface is therefore a key aspect of wound dressing performance. To date it has not been possible to monitor in any effective manner the distribution of moisture within dressings or how this varies with time.A new measurement system is presented based on sensors placed at the wound/dressing interface which are capable of monitoring moisture levels in real time. The system comprises a model wound bed and sensor array complete with fluid injection path to mimic exudate f...

Energy Technology Data Exchange (ETDEWEB)

Photodestruction has received much attention in recent years. In particular, titanium dioxide (TiO{sub 2}) and ozonolysis have attained a position of prominence. These technologies hold promise for the destruction of trace amounts of aqueous high explosives that are generated by load and pack operations, as well as demilitarization activities. Currently this water is treated by passing through a bed of activated carbon. The carbon is then steam regenerated and reused, thus creating a second waste stream which must be disposed of, or the carbon is burned directly. Recent trends in environmental regulation have shown that this may not be a viable option for process water remediation in the future. This talk will discuss efforts to employ alternate aqueous treatment techniques that not only remove the explosives compounds but are able to transform the parent compound into carbon dioxide and water. Titanium dioxide photocatalysis as well as UV-ozone photolysis will be ...

British Library Electronic Table of Contents (United Kingdom)

SummaryA meshless numerical model is proposed to investigate shallow-water dam break flows in 1D open channels. The numerical model is to solve the shallow water equations (SWE) based on smoothed particle hydrodynamics (SPH). The concept of slice water particles (SWP) is adopted in the SPH-SWE formulation. The numerical sensitivity analysis is first performed to study the appropriate SWP number and variable smoothing length through dam break flows in an idealized 1D channel with dry/wet beds. Extensive validation by comparison with laboratory and field data is next conducted for four benchmark problems, including dam break flows through a rough flat channel, a rough bumpy channel with various downstream boundary conditions, a nonprismatic channel, and a realistic scale model of the Toce ri...

Energy Technology Data Exchange (ETDEWEB)

Energy International is developing a technology that will create a staged formulation with the first coal form (Mulled Coal) that can be stored, transported, and pumped. Just prior to combustion, the Mulled Coal (MC) would be modified to provide the properties needed for proper atomization. This concept is an alternative to the expensive and energy intensive thermal drying processing of fine coal wet cakes. The material is suitable for both direct feed use in conventional and fluid bed combustors as well as on-site conversion to combustible slurries. By maintaining the coal form relatively close to the feed wet cake, only minor processing with low additive levels and low energy blending needed at the point of production. Its conversion to slurry or other use-feed form is made near the time of use and thus the requirements for stability, climatic control, and other storage, transport, and handling requirements are much less severe.

Science.gov (United States)

A process and apparatus for the production of coke, asphalt and jet fuel m a feed of fossil fuels containing volatile carbon compounds therein is disclosed. The process includes the steps of pyrolyzing the feed in an entrained bed pyrolyzing means, separating the volatile pyrolysis products from the solid pyrolysis products removing at least one coke from the solid pyrolysis products, fractionating the volatile pyrolysis products to produce an overhead stream and a bottom stream which is useful as asphalt for road pavement, condensing the overhead stream to produce a condensed liquid fraction and a noncondensable, gaseous fraction, and removing water from the condensed liquid fraction to produce a jet fuel-containing product. The disclosed apparatus is useful for practicing the foregoing process. the process provides a useful method of mass producing and jet fuels from materials such as coal, oil shale and tar sands.

International Nuclear Information System (INIS)

This paper reports that there are four combustion technologies upon which U.S. electric utilities are expected to rely for the majority of their future power generating needs. These technologies are pulverized coal- fired combustion (PC); coal-fired fluidized bed combustion (AFBC); coal gasification, combined cycle systems (CGCC); and natural gas-fired combined cycle systems (NGCC). The engineering and economic parameters which affect the choice of a technology include capital costs, operating and maintenance costs, fuel costs, construction schedule, process risk, environmental and site impacts, fuel efficiency and flexibility, plant availability, capacity factors, timing of startup, and the importance of utility economic and financial factors.

Energy Technology Data Exchange (ETDEWEB)

Very high cobalt catalysts have been prepared on steamed and acid-washed y zeolite. These catalysts are very active. Some of them have proven to be very stable. Additionally, if provisions are made to control the temperature build up on the catalyst bed, low methane selectivities result. Additional work is indicated, for instance, perhaps even higher activity catalysts can result from higher levels of cobalt or changes in the catalyst preparation procedure. Since the issue of whether small amounts of ruthenium can promote the catalyst is not completely resolved, catalyst preparation procedure experiments should continue with ruthenium vs. ruthenium-free catalysts. For instance, different methods of impregnation and/or activation should be investigated.

Energy Technology Data Exchange (ETDEWEB)

Reducing implant energy is an effective way to eliminate transient enhanced diffusion (TED) due to excess interstitials from the implant. It is shown that TED from a fixed Si dose implanted at energies from 0.5 to 20 keV into boron doping-superlattices decreases linearly with decreasing Si ion range, virtually disappearing at sub-keV energies. However, for sub-keV B implants diffusion remains enhanced and x{sub j} is limited to {ge} 100 nm at 1,050 C. The authors term this enhancement, which arises in the presence of B atomic concentrations at the surface of {approx} 6%, Boron-Enhanced-Diffusion (BED).

Energy Technology Data Exchange (ETDEWEB)

Single-particle combustion of coal char is analyzed using a generalized shrinking core model. Finite volume method, which was earlier employed by the authors in solving moving boundary problems involving fluid-solid noncatalytic reactions in general, is used to solve fully transient mass and energy equations. The model takes into account convection and diffusion inside the particle as well as in the boundary layer. The computed results are compared with the experimental data of the authors for combustion of coal char in a fluidized bed combustor. The effects of parameters such as bulk temperature and initial particle radius on the combustion dynamics are examined. The phenomena of ignition and extinction are also investigated. Finally, the importance of Stefan flow, originating due to nonequimolar counterdiffusion, on combustion of coal char is analyzed.

British Library Electronic Table of Contents (United Kingdom)

A novel liquid phase alkylation of aniline with methanol over Zn/Cu salts modified kaolin assisted with a pair of porous carbon electrode in slurry-bed reactor under constant current intensity, room temperature and atmospheric pressure was reported. The Zn/Cu salts modified kaolin catalysts were synthesized and characterized by infrared spectrometer (IR), powder X-ray diffraction (XRD) and scanning electron microscopy (SEM), which showed that the transition metals were completely supported on kaolins structure and formed a pored one. The effect parameters, such as initial pH, electrolysis time, metal ratio with kaolin and salts composition in this electrochemical catalytic system, were studied. The procedure was inspected by ultraviolet-visible spectrum (UV-vis), and the product distributi...

Energy Technology Data Exchange (ETDEWEB)

Upon request by the Science and Technology Agency of Japanese Government, the Japan Atomic Energy Research Institute has conducted Piping Reliability Test Program to demonstrate the safety and reliability of light water reactor primary pipings. In this report, the results of the program are summarized. In the test program, pipe fatigue tests, Leak-Before-Break (LBB) verification tests and pipe rupture tests were carried out to examine the integrity of pipings, to verify the LBB concept and to demonstrate the effectiveness of the protective measures against jet impingement and pipe whip under pipe rupture event, respectively. In the pipe fatigue tests, a procedure to predict the fatigue crack growth was developed and the integrity of piping during plant service life was demonstrated. In the LBB verification tests, pipe fracture ...