Energy Technology Data Exchange (ETDEWEB)

Explosives molecules have a number of unique properties. These properties are discussed. They include low vapor pressures, electronegativity, ''stickiness,'' frangibility, and thermal instability. The program for developing an advanced explosives detector is described.

Energy Technology Data Exchange (ETDEWEB)

The detection of explosives is a notoriously difficult problem, especially at stand-off distances, due to their (generally) low vapor pressure, environmental and matrix interferences, and packaging. We are exploring optimal dynamic detection to exploit the best capabilities of recent advances in laser technology and recent discoveries in optimal shaping of laser pulses for control of molecular processes to significantly enhance the standoff detection of explosives. The core of the ODD-Ex technique is the introduction of optimally shaped laser pulses to simultaneously enhance sensitivity of explosives signatures while reducing the influence of noise and the signals from background interferents in the field (increase selectivity). These goals are being addressed by operating in an optimal nonlinear fashion, typically with a single shaped laser pulse inherently containing within it coherently locked ...

International Nuclear Information System (INIS)

Decay heat removal capability under boiling condition was studied using an LMFBR fuel subassembly mockup loop. The sodium flow was driven by natural convection through the loop in which was installed a 37-pin bundle heated electrically over a length of 45 cm. The heat flux furnished by the pins was increased stepwise, upon which the two-phase flow regime changed from bubble to slug flow and then to annular or annular mist flow. Dryout occurred even in slug flow regime, but only momentarily, and permanent dryout was not observed before establichment of annular flow. A suitable criterion for permanent dryout is considered to be 0.5 average exit sodium vapor quality. The results indicated that upon occurrence of sodium boiling, the coolability of fuel subassembly would be maintained by natural convection after reactor shutdown. (author).

Energy Technology Data Exchange (ETDEWEB)

This paper describes a novel Fourier transform infrared (FTIR) spectroscopic method that can be used to rapidly screen soil samples from potentially hazardous waste sites. Samples are heated in a thermal desorption unit and the resultant vapors are collected and analyzed in a long-path gas cell mounted in a FTIR. Laboratory analysis of a soil sample by FTIR takes approximately 10 minutes. This method has been developed to identify and quantify microgram concentrations of explosives in soil samples and is directly applicable to the detection of selected volatile organics, semivolatile organics, and pesticides.

International Nuclear Information System (INIS)

... brakes lmfbr type reactors breeder reactors epithermal reactors fast reactors

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Just as FFTF has prototype components to confirm their design, FFTF is serving as a prototype for the design of the commercial LMFBR's. Design and manufacture of critical components for the FFTF system have been accomplished primarily using vendors with little or no previous experience in supplying components for high temperature sodium systems. The exposure of these suppliers, and through them a multitude of subcontractors, to the requirements of this program has been a necessary and significant step in preparing American industry for the task of supplying the large mechanical components required for commercial LMFBR's. (auth)

Science.gov (United States)

The location of defective LMFBR fuel pins by the determination of gas tag isotopic ratios is discussed. The application of this method to the FFTF Reactor briefly described.

Energy Technology Data Exchange (ETDEWEB)

The management of risks of explosives are described. Administrative and procedural controls are considered. The safety management plan involves hazard identification, risk analysis, assessment and control. The current position of explosives safety is considered. 4 tabs.

UK PubMed Central (United Kingdom)

The sensitive explosives used in initiating devices like primers and detonators are called primary explosives. Successful detonations of secondary explosives are accomplished by suitable sources of...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The author attempts to calculate the absolute characteristics of explosives unrelated to the effects of environment, particularly for that part of the work of the explosion done by the expansion of the detonation products. Setting forth his equations and noting their agreement with experimental data, he concludes that for a complete characterization of the relative effectiveness of explosives it is necessary to know the pressure, mass velocity, and polytropic index of the detonation products, but that developed considerations of the relation between performance and detonation characteristics permit a more exact evaluation of various explosives and unification of the nomenclature of explosives and methods of testing them.

International Nuclear Information System (INIS)

This paper will adress the unique safety related aspects of the LMFBR concept which are of significance to containment design and structural analyses. Topics to be covered will include: primary boundary integrity assurance; effects of sodium spills on integrity of structures; provisions being considered for containment of melted cores; and fuel handling accidents. Specific reference will be made to the FFTF and the Clinch River Breeder Reactor Project designs and methods of treatment of the above problems. In particular, the part played by tests, such as those carried out on a simulated FFTF model, and the planned structural reliability and related programs will be considered. Where practicable, these topics will be addressed in a manner which places FFTF and CRBR in context with other LMFBR's, and will point to a possible direction for future American LMFBR designs.

Energy Technology Data Exchange (ETDEWEB)

Emulsion explosives were discovered by Richard S Egley in 1961, but remained little known prior to rapid commercial development in the late 1970s. Their introduction has a significance that may in future be compared with the formulation of dynamite by Nobel in 1867 and the development of ammonium nitrate explosives in the mid 1950s. For the mining engineer emulsion explosives provide advantages of being inherently waterproof and having high strength with a high and stable velocity of detonation giving good fragmentation in hard rock. This is available at moderate cost, from an explosive that typically does not contain any self explosive ingredients and with fume properties that offer considerable advantages over other explosives. 2 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

In a slurry explosive, the fine droplets of the aqueous phase are dispersed in a continuous oily phase which comprises a thin film surrounding each droplet, the latter being less than one micron in size. The authors present these commercial explosives in three different forms, indicate their explosive properties and discuss their advantages from the safety viewpoint. They also report on tests undertaken with slurry explosives in quarries possessing different types of rock and using deep vertical shotholes.

Energy Technology Data Exchange (ETDEWEB)

The design and performance of small incinerators used at the Mound Laboratory for the disposal of explosives are described. These units, which cost less than $1000 each, are about the size of a 55-gal drum, have water jackets for cooling, and have provided a flexible, efficient, and clean burning explosives disposal unit. (LCL)

Energy Technology Data Exchange (ETDEWEB)

There is a general concern with insiders smuggling bomb quantities of explosives into sensitive facilities such as nuclear facilities. At this time, there is no single explosives detection device that is suitable for monitoring personnel and their packages for explosives in an operational facility environment. However, there are techniques combining available commercial technologies with procedures and threat analysis that can significantly increase the insiders risk and reduce the population of adversaries. This paper describes the available applicable explosives detection technologies and discusses the techniques that could be implemented on an interim basis. It is important that these techniques be considered, so that some interim level of security against the explosives threat can be established until more sophisticated equipment that is under development becomes available.

UK PubMed Central (United Kingdom)

Trinitrotoluene (TNT) absorption was assessed in groups of workers at two explosives factories by measuring the urinary concentrations of dinitroaminotoluene (DNAT) metabolites. DNAT was detected in...Full Text Available

Science.gov (United States)

... explosive (shotgun shells, etc.) method of forming is being replaced--for the most part--by the electri- cal discharge and magnetic forming methods. ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

... COMBINATION WHICH DISCUSSES AND ILLUSTRATES THE CONSTRUCTION OF AN EXPLODING BRIDGEWIRE ELECTRO-EXPLOSIVE ...

Energy Technology Data Exchange (ETDEWEB)

We have used an electric gun to measure the initiation thresholds of more than twenty unusual explosive materials as well as the thresholds of several common explosives for comparison. The purpose of the work was to obtain experimental data for a theoretical study of the effects of various chemical groups on the detonation sensitivity of explosives. 2 refs., 3 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

There have been no radically new commercial bulk explosives since Atlas Powder Company's introduction of emulsions onto the market in 1968. But the effectiveness, safety and management of these familiar explosives is continuously being improved by the development of blast design techniques, explosives delivery and initiation systems, and monitoring methods. The author looks at developments in blasting technology and discusses experiences with Handibulk emulsion delivery systems.

Energy Technology Data Exchange (ETDEWEB)

The technical rule intends to maintain the function of the safety facilities in case of explosion hazards resulting from materials capable of generating explosive atmospheres or forming explosive mixtures if such materials are brought or released into the nuclear facility or are generated on site. (orig.).

Energy Technology Data Exchange (ETDEWEB)

A direct process of making ethylenediamine dinitrate through the reaction of ethylenediamine and ammonium nitrate is described.

Science.gov (United States)

... crystals and polycrystals. Nevertheless, explosive forming, magnetic forming, etc., are all high-strain-rate processes that ...

Energy Technology Data Exchange (ETDEWEB)

A relocatable storage magazine apparatus for storing and retrieving explosives and ordnance and for partially containing and attenuating the blast, conflagration and flying debris from an accidental explosion is described comprising: (a) a container having an access hole; (b) a debris trap attached to the container, the debris trap communicating with said container via the access hole, said debris trap having vent holes for venting the pressure of an explosion from said debris trap to the atmosphere; (c) means for covering said access hole; (d) means for suspending explosives and ordnance from the covering means; (e) means for entering the storage magazine to store and retrieve explosives and ordnance; (f) means for retaining said covering means in a position above the access hole wherein said explosives and ordnance are accessible from the entering means.

Energy Technology Data Exchange (ETDEWEB)

The object of this Regulation is to provide for those matters that may be, or that are required to be, the subject of regulations under the Explosives Act 2003, The Regulation deals with the following maters: a) a register of authorised and prohibited explosives (Part. 2), b) the classification of explosives (Part. 3), c) matters related to licences under the Explosives Act 2003, including the types of licences, requirements for obtaining licences, certain prescribed licence conditions and certain exemptions from the requirement to have a licences (Part. 4), d) specific control measures relating to the handling of explosives (Part. 5), e) matters of a savings, transitional or administrative nature (Part. 1 and 6). This Regulation refers to the following documents: a) AS 2187, Explosives-storage, transport and use, as published by Standards Australia and in force ...

Science.gov (United States)

The theory of a method of determination of reactivity from power spectral density measurements with /sup 252/Cf and the results of experiments with a critical assembly mockup of a liquid-metal fast breeder reactor (LMFBR) and with uranium (93.2 wt % /sup 235/U) metal cylinders and a sphere are presented. This method of reactivity determination has an advantage over existing methods in that it determines the reactivity only from properties of the reactor at the subcritical state of interest and thus does not require a calibration near delayed criticality. In these experiments, the reactivity was varied by changing the fissile loading or the amount of neutron absorber inserted; for the LMFBR mockup, the reactivity varied to approximately 75 dollars subcritical, and for the uranium metal assemblies to approximately 30 dollars subcritical. These experiments verified for the first time the predictions of theory that could be tested in the ...

International Nuclear Information System (INIS)

Water flow experiments were conducted on natural circulation decay heat removal with an electrically heated 91-rod bundle. Experimental results were compared with analytical predictions to provide thermal hydraulic characteristics for LMFBR Fuel assemblies under a low flow, typical of the natural circulation regime. The results revealed that, at low flow rate region (Re<1,200), axial friction loss in a heated bundle increases with buoyancy effect. The radial temperature profile provides some insight regarding the concept that coolant redistribution would occur. COBRA-V-I predictions are successfully proved validity in comparison with experimental results.

Energy Technology Data Exchange (ETDEWEB)

In response to a request from DOE-SR, the current state of knowledge of the reactions between TBP and aqueous nitrate solutions is critically reviewed, and recommendations are made for the safe operation of SRS separations equipment in which this combination of chemicals may be present. The existing limits for evaporation are validated. Guidelines are presented for cases in which general limits do not apply. The rate of reaction between nitric acid and TBP appears to be controlled by the rate of TBP hydrolysis. The hydrolysis reaction produces dibutyl phosphate and n-butanol. The hydrolysis rate is a strong function of temperature, and becomes very fast at temperatures in the range 130{degrees} to 150{degrees}C. The resulting n-butanol is volatile at high temperatures, boiling at 117.5{degrees}C, but is also subject to exothermic oxidation by nitric acid or nitrates. If oxidation occurs before the n-butanol evaporates, the heat of oxidation may exceed local cooling by convection. The ...

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) bottom-loading transfer cask (BLTC) system is designed to provide ex-vessel fuel transfers of irradiated reactor components between the reactor containment building and the LMFBR shipping cask in the reactor service building. This system is being procured from National Lead Industries, Wilmington, Delaware, under management of Aerojet Manufacturing Company.

Energy Technology Data Exchange (ETDEWEB)

This handbook presents information and data for high explosives (HEs) of interest to programs at the Lawrence Livermore National Laboratory (LLNL) and other Department of Energy (DOE) facilities. It is intended to be useful to the scientist or engineer, the novice or expert, who needs to develop a new weapon system, design a physics experiment, or select and/or evaluate an existing explosive. This compilation is limited to production HEs and their components. High explosives are divided into two classes: initial detonating (or primary) and noninitiating (or secondary) explosives. The primary HEs, such as azides and fulminates, are extremely sensitive to ignition by heat, shock, and electrical discharge; ignition leads to high-order detonation of the material - even for milligram quantities. The use of these HEs is therefore limited to squibs and starting materials for low-energy detonators. Because ...

Energy Technology Data Exchange (ETDEWEB)

Both DOE and DOD use water and/or steam in the process of removing high explosives, resulting in large quantities of contaminated water, which is then run through activated carbon, which then has to be decontaminated. Research has been underway to utilize microorganisms to degrade RDX and HMX.

UK PubMed Central (United Kingdom)

Several independent studies of bacterial degradation of nitrate ester explosives have demonstrated the involvement of flavin-dependent oxidoreductases related to the old yellow enzyme (OYE) of yeast....Full Text Available

Energy Technology Data Exchange (ETDEWEB)

We have investigated tailoring damage effects of explosive devices by addition of unconventional materials, specifically combustible metals. Initial small-scale as well as full-scale testing has been performed. The explosives functioned to disperse and ignite these materials. Incendiary, enhanced-blast, and fragment-damage effect have been identified. These types of effects can be used to extend the damage done to hardened facilities. In other cases it is desirable to disable the target with minimal collateral damage. Use of unconventional materials allows the capability to tailor the damage and effects of explosive devices for these and other applications. Current work includes testing of an incendiary warhead for a penetrator.

Energy Technology Data Exchange (ETDEWEB)

This paper describes the phenomenology of nuclear explosions and technologies for their detection as relevant to On-Site Inspection (OSI) for a comprehensive test-ban (CTB). Our experience with the US nuclear test program which has been primarily carried out at the Nevada Test Site (NTS) and in the Pacific Ocean. The goals of OSI are to resolve ambiguous events, reduce uncertainty, deter attempts at evasion, and provide responsive and technically competent means of confirming the occurrence of a nuclear explosion should deterrence fail. These goals would include finding evidence of an evasive nuclear explosion or evidence that the event was non-nuclear, such as an earthquake or large chemical explosion.

Energy Technology Data Exchange (ETDEWEB)

17 papers are presented. Topics covered include: the POG system - a new concept in the use of ANFO; demolition of a motorway bridge; presplit and smooth blasting; VIBReX - a predictive code for assessing the effect of blast design on ground vibration; ground vibrations from blasting; digital seismographs; human response to blasting and the effects on planning conditions; landform construction by restoration blasting; use of small diameter explosives; efficient priming; safety management in the explosives industry; and the law on packaging of explosives. Two papers have been abstracted separately.

Science.gov (United States)

... Descriptors : *INTERIOR BALLISTICS, *COMBUSTIBLE CARTRIDGE CASES, FIRING TESTS(ORDNANCE), EXPLOSIVE CHARGES, ARTILLERY ...

Science.gov (United States)

... Casting Explosive forming Forging Electrohydraulic forming Extruding Magnetic forming Rolling Electroforming Drawing Powdered metal forming ...

Energy Technology Data Exchange (ETDEWEB)

Small-scale methods for determining the reaction rates of explosives that make it possible to predict safe temperatures for using them, and methods for testing the accuracy of these predictions were developed. Each different size and shape of each different explosive has its own critical temperature. The ability to predict these critical temperatures is required before high-energy materials can be used safely.

Energy Technology Data Exchange (ETDEWEB)

This report describes a high explosives test facility that makes efficient use of equipment and combines utility, convenience, and safety in a modest amount of space. It is a dedicated facility for exploratory development efforts that previously were conducted in a single room having very limited capabilities. Two explosives testing areas are now available and several projects are supported concurrently.

Energy Technology Data Exchange (ETDEWEB)

In recent years new, less-sensitive explosives have been developed together with new types of detonator. Four sections are covered: 1) Description of various developments achieved by the laboratories of Nobel Explosifs over the past 12 years; 2) Explanation of the limits of application of the various products; 3) Thoughts on the various detonator systems and their effectiveness; and 4) Advice and recommendations for the use of the new product range. The products in question are : dynamites, nitrates, oil nitrates, gels and slurry explosives. (17 refs.)

Energy Technology Data Exchange (ETDEWEB)

Short communication.

Energy Technology Data Exchange (ETDEWEB)

The US Plowshare program, designed to develop peaceful uses of nuclear explosives, was vigorous between 1957-73 and was of concern during US and USSR nuclear treaty negotiations within that period. In order to accommodate possible future applications, the Peaceful Nuclear Explosions Treaty was signed in 1976. The US program explored the phenomenology of nuclear explosions and tested their use in industrial applications. Due to waning industrial interest and public concern over environmental issues, the US program was terminated in 1977. The Soviet counterpart to the Plowshare program, which has involved more than 100 experiments throughout the USSR, continued until the self-imposed moratorium in 1985. As any peaceful use of nuclear explosives has the potential of furthering weapons research, the US takes the position that all such experiments would have to be banned in a comprehensive test ban treaty. ...

Energy Technology Data Exchange (ETDEWEB)

The Idaho Explosives Detection System was developed at the Idaho National Laboratory (INL) to respond to threats imposed by delivery trucks potentially carrying explosives into military bases. A full-scale prototype system has been built and is currently undergoing testing. The system consists of two racks, one on each side of a subject vehicle. Each rack includes a neutron generator and an array of NaI detectors. The two neutron generators are pulsed and synchronized. A laptop computer controls the entire system. The control software is easily operable by minimally trained staff. The system was developed to detect explosives in a medium size truck within a 5-min measurement time. System performance was successfully demonstrated with explosives at the INL in June 2004 and at Andrews Air Force Base in July 2004.

British Library Electronic Table of Contents (United Kingdom)

Soufriere Hills Volcano had two periods of repetitive Vulcanian activity in 1997. Each explosion discharged the contents of the upper 0.5-2km of the conduit as pyroclastic flows and fallout: frothy pumices from a deep, gas-rich zone, lava and breadcrust bombs from a degassed lava plug, and dense pumices from a transition zone. Vesicles constitute 1-66vol.% of breadcrust bombs and 24-79% of pumices, all those larger than a few tens of m being interconnected. Small vesicles (few hundreds of m) in pumices are interpreted as pre-dating explosion, implying pre-explosive conduit porosities up to 55%. About a sixth of large vesicles in pumices, and all those in breadcrust bombs, are angular voids formed by syn-explosive fracturing of amphibole phenocrysts. An intermediate-sized vesicle population...

Energy Technology Data Exchange (ETDEWEB)

A simple model based on surface chemistry is developed, based an simple concepts of contact angle, wetting and spreading. Results of the modeling can be stated by two simplified ``rules of thumb``: (1) A liquid will spread on the surface of a solid if the surface tension of the liquid is lose than the surface free energy of the solid, and (2) The liquid having the surface tension nearest that of the solid will preferentially wet the surface of the solid. These two rules can then be used to define the parameters that constitute a process for formulating a plastic bonded explosive (PBX), which is a crystalline high-explosive material coated with a small amount of plastic polymeric material (the binder). The PBX then can be pressed to a high density, and machined to a specific shape. The pressed and machined explosive material can then be used in a physics experiment to study fundamental properties of either the ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents the new thermal hydraulic models describing the hydrodynamics of the solid fuel/steel chunks during an LMFBR hypothetical core-disruptive accident. These models, which account for two-way coupling between the solid and fluid phases, describe the mass, momentum, and energy exchanges which occur when the chunks are present at any axial location. They have been incorporated in LEVITATE, a code for the analysis of fuel and cladding dynamics under Loss-of-Flow (LOF) conditions. Their influence on fuel motion is presented in the context of the L6 TREAT experiment analysis. It is shown that the overall hydrodynamic behavior of the molten fuel and solid-fuel chunks is dependent on both the size of the chunks and the power level. At low and intermediate power levels the fuel motion is more dispersive when small chunks, rather than large ones, are present. At high power levels the situation is reversed. These effects are explained in detail.

Energy Technology Data Exchange (ETDEWEB)

The JUPITER-II Program is the Joint Physics Large Heterogeneous Core Critical Experiments Program between the U.S. Department of Energy (US DOE) and PNC, Japan. The experiments began in May 1982 and ended in April 1984, as a part of the ZPPR-13 program. The ZPPR-13 is a series of critical assemblies designed to study the fundamental neutronic behavior of large, radially-heterogeneous LMFBR cores. This report describes the results of analysis of ZPPR-13A and preliminary analysis of ZPPR-13B, and some topics of recent activities in fast reactor physics.

International Nuclear Information System (INIS)

This paper presents the objective, scope, and status of the U.S. Department of Energy's Materials and Structures Program to develop a data base on mechanical properties of structural materials for out-of-core structures and components for LMFBRs. Information on the development of a reference data base on materials for the reactor system, reactor enclosure system, primary heat transport system, intermediate heat transport system, and steam generator system is included. In addition, the development of the data and analyses to account for the effects of temperature and stress, as well as water/steam, sodium, and radiation environments, is described. Plans for the development of alternative materials for future out-of-core applications are presented. (author).

International Nuclear Information System (INIS)

In the analysis of the consequences of a hypothetical meltdown accident in an LMFBR, it is important to estimate the final location of the molten fuel pool in the concrete and ground underlying the reactor vessel. The GROWS program and the AYER program have been developed to calculate the final location of the molten fuel pool as the culmination of the transient analysis of this unusual Stefan problem but these programs require extensive computational resources. The solution is provided to the concrete and ground temperatures surrounding the stationary fuel pool and the related heat flux from the pool to the ground surface outside the containment building. This solution can be used to estimate the final location of the fuel pool and to check the end results of the sophisticated programs.

Science.gov (United States)

In order to reduce the air concentration of (sup 3)H in the reactor buiIding of Wolsung Heavy Water Reactor, a computer code for estimation of adsorption behavior was programmed based on an equation derived for analysis of water vapor adsorption, and a ba...

CERN Document Server

The phenomenon of time resonances (or explosions) can explain the exponential reduction of the energy, which is accompanied for the certain degree by slight fluctuations under some conditions in the range of the energy strongly overlapped compound-resonances. These resonant explosions correspond to formation of several highly-exited non-exponentially decaying nuclear clots (partial compound nuclei consisting of several small groups of projectile nucleons and targets). This paper is a continuation and expansion of theoretical authors' work, which is a more general self-consistent version of the time-evolution approach in comparison with the traditional Izumo-Araseki time compound-nucleus model.

Energy Technology Data Exchange (ETDEWEB)

A method of detecting explosives in a vehicle includes providing a first rack on one side of the vehicle, the rack including a neutron generator and a plurality of gamma ray detectors; providing a second rack on another side of the vehicle, the second rack including a neutron generator and a plurality of gamma ray detectors; providing a control system, remote from the first and second racks, coupled to the neutron generators and gamma ray detectors; using the control system, causing the neutron generators to generate neutrons; and performing gamma ray spectroscopy on spectra read by the gamma ray detectors to look for a signature indicative of presence of an explosive. Various apparatus and other methods are also provided.

Energy Technology Data Exchange (ETDEWEB)

One of the concerns with locating radioactive waste storage sites in salt deposits is how to permanently seal the underground storage areas once they have reached their storage capacity. The compaction of salt using explosives has been identified as a potential method of producing permanent seals in both entryways and shafts to storage areas. This paper describes the test procedure and results of a preliminary investigation to determine the feasibility of utilizing explosives in the compaction of salt. Three simple tests were carried out to measure the degree to which loose salt could be compacted.

Science.gov (United States)

Ultimate Compressive Strength = 3000.0 psi. 3.0 Failure Criteria. The structural criteria used to evaluate the combustor components was chosen ...

British Library Electronic Table of Contents (United Kingdom)

Effective integration of nonproliferation management into the design process is key to the broad deployment of advanced nuclear energy systems, and is an explicit goal of the Laser Inertial Fusion Energy (LIFE) project at Lawrence Livermore National Laboratory. The nuclear explosives utility of a nuclear material to a state (proliferator) or sub-state (terrorist) is a critical factor to be assessed and is one aspect of material attractiveness. In this work, we approached nuclear explosives utility through the calculation of a ''figure of merit'' (FOM) that has recently been developed to capture the relative viability and difficulty of constructing nuclear explosives starting from various nuclear material forms and compositions. We discuss the integration of the figure of merit into an asse...

Science.gov (United States)

... an Page 15. NSWC TR 86-32 exploding bridgewire detonator containing PETN rather, than a pri'mary explosive. However ...

Science.gov (United States)

... and high-quality photospheric-phase Type II SN spectra to constrain core- collapse SN explosions, massive star evolution, and distances in the Universe ...

Science.gov (United States)

... for. Now there already exists under the SPIA aegis a document which is called the JANAP mailing list. This is the joint Army ...

Energy Technology Data Exchange (ETDEWEB)

We describe a new method for the scabbling of concrete surfaces using a thin layer of explosive material sprayed onto the surfaces. We also developed a new explosive mixture that could be applied with commercial spray painting equipment. The first part of our record describes experiments that studied methods for the initiation of the sprayed explosive. We successfully initiated layers 0.36 mm thick using a commercial EBW detonator, a flying plate detonator, and by pellet impact. The second part of our report describes a survey of spray methods and tests with two commercial spray systems that we believe could be used for developing a robotic spray system.

Science.gov (United States)

May 13, 2010 ... Abstract: On April 20, 2010, an explosion occurred on the semi-submersible offshore drilling rig Deepwater Horizon in the Gulf of Mexico, ...

Energy Technology Data Exchange (ETDEWEB)

The relative abundances of iron-peak elements produced by the e-process in a supernova outburst are calculated. The results agree quite well with the cosmic abundances of elements in the range Z=23--28.

Energy Technology Data Exchange (ETDEWEB)

This paper discusses geology, coalfields, coal quality, seams and strata, coal reserves, mining methods, production, coal liquefaction, and research on spontaneous combustion and methane explosions.

British Library Electronic Table of Contents (United Kingdom)

Villarrica (Chile) is one of the most active volcanoes in South America having erupted about 60 times in the last 460years. Although its historical eruptive activity has been mainly effusive and weakly explosive, it had strong explosive behaviour in postglacial times. Chaimilla (<3.1ka) is one of the best exposed and widely dispersed pyroclastic deposits, related to both fall and flow activity. The deposit is dispersed over an area of 250km^2 and consists of 8 units (A-H) which were grouped into four sequences. Stratigraphic data suggest that the eruption had a relatively short duration and evolved from i) an Opening phase, dispersing ash, lapilli clasts, accretionary lapilli, blocks and bombs, to ii) a Pulsatory phase, originating a series of magmatic explosions, to iii) a Collapsing phas...

Energy Technology Data Exchange (ETDEWEB)

Because of the importance of water vapor, the ARM program initiated a series of three intensive operating periods (IOPs) at its CART (Cloud And Radiation Testbed) site. The goal of these IOPs is to improve and validate the state-of-the-art capabilities in measuring water vapor. To date, two of the planned three IOPs have occurred: the first was in September of 1996, with an emphasis on the lowest kilometer, while the second was conducted from September--October 1997 with a focus on both the upper troposphere and lowest kilometer. These IOPs provided an excellent opportunity to compare measurements from other systems with those made by the CART Raman lidar. This paper addresses primarily the daytime water vapor measurements made by the lidar system during the second of these IOPs.

Energy Technology Data Exchange (ETDEWEB)

This study aims to develop a particulate model combining solid waste particle combustion and heavy metal vaporization from burning particles during MSW incineration in a fluidized bed. The original approach for this model combines an asymptotic combustion model for the carbonaceous solid combustion and a shrinking core model to describe the heavy metal vaporization. A parametric study is presented. The global metal vaporization process is strongly influenced by temperature. Internal mass transfer controls the metal vaporization rate at low temperatures. At high temperatures, the chemical reactions associated with particle combustion control the metal vaporization rate. A comparison between the simulation results and experimental data obtained with a laboratory-scale fluid bed incinerator and Cd-spiked particles shows that the heavy metal vaporization is ...

Energy Technology Data Exchange (ETDEWEB)

The Federal Aviation Administration (FAA) identified 17 accidents that may have resulted from fuel tank explosions on commercial aircraft from 1959 to 2001. Seven events involved JP 4 or JP 4/Jet A mixtures that are no longer used for commercial aircraft fuel. The remaining 10 events involved Jet A or Jet A1 fuels that are in current use by the commercial aircraft industry. Four fuel tank explosions occurred in center wing tanks (CWTs) where on-board appliances can potentially transfer heat to the tank. These tanks are designated as ''Heated Center Wing Tanks'' (HCWT). Since 1996, the FAA has significantly increased the rate at which it has mandated airworthiness directives (ADs) directed at elimination of ignition sources. This effort includes the adoption, in 2001, of Special Federal Aviation Regulation 88 of 14 CFR part 21 (SFAR 88 ''Fuel Tank System Fault Tolerance Evaluation ...

British Library Electronic Table of Contents (United Kingdom)

Tthe acceleration of a liquid from a cylindrical container by the products of instantaneous detonation of a superimposed explosive charge (implosion method) is studies numerically in a two-dimensional formulation. Analytical formulas for the asymptotic velocities of liquid expansion and acceleration of the container body were obtained using numerical calculations in a one-dimensional approximation. The effect of the fracture of the body on the velocity of liquid expansion was studied in a two-dimensional formulation.

International Nuclear Information System (INIS)

In this study the development of a methodology to detect illicit drugs and plastic explosives is described with the objective of being applied in the realm of public security. For this end, non-destructive assay with neutrons was used and the technique applied was the real time neutron radiography together with computerized tomography. The system is endowed with automatic responses based upon the application of an artificial intelligence technique. In previous tests using real samples, the system proved capable of identifying 97% of the inspected materials.

Energy Technology Data Exchange (ETDEWEB)

Researchers at Lawrence Livermore National Laboratory are developing high-performance explosive firing vessels to contain (one time) explosive detonations that contain toxic metals and hazardous gases. The filament-wound polymer composite vessels are designed to contain up to 80 lb (TNT equivalent) explosive in a 2-meter sphere without leakage. So far, two half-scale (1-meter diameter) vessels have been tested; one up to 150% of the design explosive limit. Peak dynamic pressures in excess of 280 MPa (40 Ksi) in the vessel were calculated and measured. Results indicated that there was a small amount of gas and particle leakage past the first two of the seven o-ring seals. However, the remaining five seals prevented any transient leakage of the toxic gases and particulates out of the vessel. These results were later confirmed by visual inspection and particulate analysis of swipes taken from the sealing ...

Energy Technology Data Exchange (ETDEWEB)

The two-dimensional Eulerian hydrodynamic code 2DE with the shock initiation of heterogeneous explosive burn model called Forest Fire, is used to model numerically the interaction of jets of steel, copper, tantalum, aluminum, and water with steel, water, and explosive targets. The calculated and experimental critical condition for propagating detonation may be described by the Held V/sup 2/d expression (jet velocity squared times the jet diameter). In PBX 9502, jets initiate an overdriven detonation smaller than the critical diameter, which either fails or enlarges to greater than the critical diameter while the overdriven detonation decays to the C-J state. In PBX 9404, the jet initiates a detonation that propagates only if it is maintained by the jet for an interval sufficient to establish a stable curved detonation front. The calculated penetration velocities into explosives, initiated by a low-velocity jet, are ...

Energy Technology Data Exchange (ETDEWEB)

Managing sites contaminated with munitions constituents is an international challenge. Although the choice of approach and the use of Ecological Risk Assessment (ERA) tools may vary from country to country, the assurance of quality and the direction of ecotoxicological research are universally recognized as shared concerns. Drawing on a multidisciplinary team of contributors, 'Ecotoxicology of Explosives' provides comprehensive and critical reviews available to date on fate, transport, and effects of explosives. The book delineates the state of the science of the ecotoxicology of explosives, past, present, and recently developed. It reviews the accessible fate and ecotoxicological data for energetic materials (EMs) and the methods for their development. The chapters characterize the fate of explosives in the environment, then provide information on their ecological effects in key ...

Energy Technology Data Exchange (ETDEWEB)

Film boiling is the mode if boiling during which the hot surface is separated from the vaporizing liquid by a nearly continuous film vapor. Film boiling is usually considered a very undesirable boiling regime since it is a relatively quiet and inefficient mode of heat transfer, particularly as compared to nucleate boiling. It is customary to analyze the two-phase flow regime of laminar flow film boiling by assuming the two-phase flow regime of laminar flow film boiling by assuming an idealized vapor film flow characterized by a smooth liquid-vapor interface. However, during stable flow film boiling, the wavy nature of the liquid-vapor interface and its role in local heat and mass transport have been largely ignored. The vapor interface is rarely stationary. Interfacial waves may substantially augment the heat transfer rates throughout the layer. The present ...

International Nuclear Information System (INIS)

In the revised GCFR Safety Program Plan a quantitative risk limit line has been adopted to establish requirements for the safety related functions and systems. The risk limit line is derived from an interpretation of NRC established licensing requirements, including those for LMFBR's. Multiple barriers to the progression of accident sequences are defined in the form of six Lines of Protection (LOPs). LOPs-1 to 3 are dedicated to accident prevention and represent the normal operating systems, the dedicated safety systems and the inherent design features, respectively. LOPs-4 to 6 are dedicated to the mitigation of core melt accident consequences and include in-vessel accident containment, secondary containment integrity and radiological attenuation, respectively. Cumulative frequency limits and consequence limits are established for each LOP. Design features associated with each LOP are described and the results of supporting safety analyses are summarized. ...

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) is a 400 Mw(t), loop-type, sodium-cooled, fast neutron reactor. It is operated by the Westinghouse Hanford Company for the United States Department of Energy at Richland, Washington. The FFTF is a multipurpose test reactor used to irradiate fuels and materials for programs such as Liquid Metal Reactor (LMR) research, fusion research, space power systems, isotope production and international research. FFTF is also used for testing concepts to be used in Advanced Reactors which will be designed to maximize passive safety features and not require complex shutdown systems to assure safe shutdown and heat removal. The FFTF also provides experience in the operation and maintenance of a reactor having prototypic components and systems typical of large LMR (LMFBR) power plants. The 5 year operational performance of the FFTF reactor is discussed in this report. 6 refs., 10 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

A numerical analysis is performed to clarify the heat transfer characteristics of combined convection around the tubes which form a single row perpendicularly arranged to a forced flow in the direction of gravity. A boundary-fitted coordinate transformation technique is adopted to solve the governing equations numerically. It is found in the case of liquid sodium that gravity-induced flow gives no substantial effect to heat transfer augmentation in a low Reynolds number region while it can be sufficiently expected in the ordinary fluids in the same Reynolds number region. This means that such heat transfer augmentation as expected in ordinary fluids can not be realized when crossflow-type heat exchangers installed for decay-heat removal operates in a low Reynolds number region.

Energy Technology Data Exchange (ETDEWEB)

Coal was treated at high temperature under high pressure in the binary system mixed solvent of water and organic solvent, and the solvent treated coal was liquefied. When the treated coal was treated again by the explosive method in which high temperature and pressure were released immediately, the oil yield was higher than that by the normal method in which high temperature and pressure were reduced gradually to room temperature and atmospheric pressure. In this study, an explosive treatment unit with increased scale of sample amount was newly fabricated. Illinois No.6 coal was treated by the explosive method in a mixed solvent of water and cyclohexanol using this unit. Changes in shape on the surface, specific surface area, and functional groups were analyzed. The explosively treated coal contained more amount of low boiling point components than the normally treated coal. It was suggested that the ...

Energy Technology Data Exchange (ETDEWEB)

A special study was conducted to investigate the influences of minimum approach temperature differences occurring in supercritical-heater/vaporizer and evaporative-condenser heat rejection systems on geothermal-electric binary power plant performance and cost of electricity. For the systems investigated optimum pinch points for minimizing cost of electricity were estimated to range from 5 to 7/sup 0/F for the heater vaporizer. The minimum approach of condensing temperature to wet-bulb temperature for evaporative condensers was estimated to be about 30/sup 0/F in order to achieve the lowest cost of electricity.

British Library Electronic Table of Contents (United Kingdom)

Between 1986 and 1990 the eruptive activity of Erebus volcano was monitored by a video camera with on-screen time code and recorded on video tape. Corresponding seismic and acoustic signals were recorded from a network of 6 geophones and 2 infrasonic microphones. Two hundred Strombolian explosions and three lava flows which were erupted from 7 vents were captured on video. In December 1986 the Strombolian eruptions ejected bombs and ash. In November 1987 large bubble-bursting Strombolian eruptions were observed. The bubbles burst when the bubble walls thinned to ?20?cm. Explosions with bomb flight-times up to 14.5?s were accompanied by seismic signals with our local size estimate, ?unified magnitudes?? (mu), up to 2.3. Explosions in pools of lava formed by flows in the Inner Crater were co...

Energy Technology Data Exchange (ETDEWEB)

Photodestruction has received much attention in recent years. In particular, titanium dioxide (TiO{sub 2}) and ozonolysis have attained a position of prominence. These technologies hold promise for the destruction of trace amounts of aqueous high explosives that are generated by load and pack operations, as well as demilitarization activities. Currently this water is treated by passing through a bed of activated carbon. The carbon is then steam regenerated and reused, thus creating a second waste stream which must be disposed of, or the carbon is burned directly. Recent trends in environmental regulation have shown that this may not be a viable option for process water remediation in the future. This talk will discuss efforts to employ alternate aqueous treatment techniques that not only remove the explosives compounds but are able to transform the parent compound into carbon dioxide and water. Titanium dioxide photocatalysis as well as ...

Energy Technology Data Exchange (ETDEWEB)

The authors examine the overheating of a chemical detonation wave, which results in hybrid detonation processes, for example, photochemical or electrochemical detonation, depending on the source. The schemes for obtaining the overheated detonation are shown. Analysis has shown that: normal stationary overheated detonation waves are possible when the overheating power density is constant, just as when the specific energy of overheating is constant; the use of the ''gas'' equation of state for describing overheated detonation in condensed explosives yields wave parameters which are too high; and the assumption that the chemical energy released in the explosive is independent of the overheating energy also leads to wave parameters which are too high, and the overestimation increases as the overheating is intensified.

Science.gov (United States)

Mine rescue teams frequently must fight fires and guard against the propagation of fires or explosions during a rescue and recovery operation. The team's ability to fight fires depends a great deal on hands-on experience with different fire fighting agents and equipment. The team's work includes an assessment of fire conditions, mine fire gases and other potential hazards associated with fire fighting activity. This training module covers the underlying principles of the fire triangle and the different methods for controlling, containing and extinguishing fires in a mine. The manual also covers fire-fighting equipment, considerations involved in a sealing operation and the cause-effect of explosions.

British Library Electronic Table of Contents (United Kingdom)

Fires and explosions have been identified as major potential hazards for Oil and Gas Floating Production Storage Offloading (FPSO) installations and pose risk to personnel, assets, and the environment. Current fire and explosion assessment (FEA) tools require physical effect modeling software and follows standards from API, ISO, and engineering practices. However, the tools are not specific to any particular system such as an FPSO, and do not provide comprehensive guidance for safety engineers to perform FEA. This paper discusses the development of a screening and comparison tool for FEA on FPSOs and the incorporation of an expert system into the tool. The results are computerized using MS Excel/VBA to provide a structured and comprehensive assessment on each equipment and module handling ...

CERN Document Server

We present the results of an ongoing project to use the X-ray observations of Type Ia Supernova Remnants to constrain the physical processes involved in Type Ia Supernova explosions. We use the Tycho Supernova Remnant (SN 1572) as a benchmark case, comparing its observed spectrum with models for the X-ray emission from the shocked ejecta generated from different kinds of Type Ia explosions. Both the integrated spectrum of Tycho and the spatial distribution of the Fe and Si emission in the remnant are well reproduced by delayed detonation models with stratified ejecta. All the other Type Ia explosion models fail, including well-mixed deflagrations calculated in three dimensions.

British Library Electronic Table of Contents (United Kingdom)

A constitutive model for an explosive consists of three parts: equation of state of reactants, equation of state of products, and reaction rate. In the absence of a good physical theory, models are empirical and based on heuristics. For the HMX based plastic-bonded explosive PBX 9501, three models have previously been calibrated and used in numerical simulations. Here, these three models are compared. They illustrate several generic difficulties with developing and validating models. The available data is insufficient to determine a constitutive model uniquely. Different models can be calibrated to fit the available data yet differ significantly in regions of phase space of importance to applications. Comparing models gives an indication of the uncertainty in model predictions outside the ...

Energy Technology Data Exchange (ETDEWEB)

Using gasoline as an example of additives for cold start improvement, fuel vapor composition of methanol-gasoline mixtures, fuel evaporation rate in consideration of temperature drop due to heat of fuel evaporation, air fuel ratio, stoichiometric air fuel ratio and excess air ratio of fuel vapor were calculated. The mixture formation of methanol-gasoline mixtures at low temperature in otto cycle engines was studied. Van Laar's empirical formula was used to estimate the partial pressure of high-percentage methanol blends. It was found that the most part of fuel vapor is occupied by gasoline, even when a small amount of gasoline is added to methanol resulting to an extremely small excess air ratio. It is obvious that this vapor pressure adjustment using gasoline is the dominant factor for improvement in cold startability. (10 figs, 1 tab, 10 refs)

Energy Technology Data Exchange (ETDEWEB)

We present a 1-D heat transfer, melting, vaporization and resolidification model describing the interaction of a scanning continuous-wave laser with a metal surface wherein the beam power is constant. A physical model based on the Stefan problem is developed with appropriate boundary conditions. The effects of processing parameters on process variables are investigated numerically by varying beam diameters, scan speeds and substrate temperatures for Nickel. Relations are derived for the times to initiate melting, to initiate vaporization, to reach maximum melting depth, for melting-resolidification, and for maximum melting and vaporization depths. Surface temperatures are compared with approximate closed form solutions. (Author)

British Library Electronic Table of Contents (United Kingdom)

In radio signal-based observing systems, such as Global Positioning System (GPS) and Interferometric Synthetic Aperture Radar (InSAR), the water vapor in the atmosphere will cause delays during the signal transmission. Such delays vary significantly with terrain elevation. In the case when atmospheric delays are to be eliminated from the measured raw signals, spatial interpolators may be needed. By taking advantage of available terrain elevation information during spatial interpolation process, the accuracy of the atmospheric delay mapping can be considerably improved. This paper first reviews three elevation-dependent water vapor interpolation models, i.e., the Best Linear Unbiased Estimator in combination with the water vapor Height Scaling Model (BLUE?+?HSM), the Best Linear Unbiased Es...

Energy Technology Data Exchange (ETDEWEB)

Apparatus and method are described for the vaporization of liquid fuel oils to produce a gaseous mixture suitable for burning in a burner normally designed for operation utilizing natural gas.

British Library Electronic Table of Contents (United Kingdom)

In this study, we thoroughly analyzed abrupt behaviors, trends, and periodicity properties of water vapor flux and moisture budget entering and exiting the four edges of the Pearl River basin based on the NCAR/NCEP reanalysis dataset by using the continuous wavelet transform and the simple two-phase linear regression technique. Possible implications for hydrological cycle and water resource management of these changes are also discussed. The results indicate that: (1) the water vapor propagating through the four edges of the Pearl River basin is decreasing, and it is particularly true for the changes of the water vapor flux exiting from the north edge of the study river basin. The transition point from increase to decrease occurs in the early 1960s; (2) The wavelet transform spectra indica...

UK PubMed Central (United Kingdom)

N-substituted aromatics are important priority pollutants entering the environment primarily through anthropogenic activities associated with the industrial production of dyes, explosives, pesticides,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Information is provided about standardization and unification of rules for manufacturing normal electrical equipment designed for operating in underground shafts when there is no danger of explosion of gas, dust or steam. An analysis is made of the requirements included in the CEMA standard and in the state standard.

Science.gov (United States)

Apr 25, 2010... oil per day were leaking from an oil well in the Gulf of Mexico in late April, following an explosion at an offshore drilling rig on April 20, 2010. ...

UK PubMed Central (United Kingdom)

Aims: To investigate the exposure to dinitrotoluene (DNT) and trinitrotoluene (TNT) and the resulting effects in workers which occur during the disposal of military waste. Methods:...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The nonequilibrium Zeldovich-von Neumann-Doring theory of detonation in solid explosives is extended to include recent nanosecond and picosecond experimental and theoretical results on each of the four main regions of the reaction zone. The first region is the three-dimensional, Mach stem dominated leading shock front which excites the phonon modes of the explosive molecules in less than a picosecond. The second region is the multiphonon up-pumping process in which the excited phonons anharmonically couple to the low frequency (doorway) vibrational modes which in turn equilibrate with the higher frequency modes by internal vibrational redistribution. This process may require on the order of tens of picoseconds. The third region is the chemical reconstitution region in which the vibrationally equilibrated transition state decomposes in a series of chain reaction steps into highly vibrationally excited diatomic and triatomic molecules in ...

Energy Technology Data Exchange (ETDEWEB)

This report presented an analysis of incidents gathered by the Canadian upstream oil and gas industry committee in relation to explosive atmospheres in wellbores, vessels, tanks, and piping systems. The aim of the report was to develop industry recommended practices for oil and gas industry fires and explosions. Two accident theory models were used to set out the relationships between hazards, defenses, and losses. Three levels of defenses were identified based on organizational, local workplace, and human factors. An organizational responsibility approach was used to examine the activities of key people with the system. Incidents were analyzed based on an expanded fire triangle used to identify fire and explosion hazards. The study showed that the ignition of hydrocarbons into the air was a factor in nearly 50 per cent of the incidents. A lack of understanding of liquid-hydrocarbon properties was demonstrated in incidents ...

UK PubMed Central (United Kingdom)

BackgroundWith the explosion in data generated using microarray technology by different investigators working on similar experiments, it is of interest to combine results across...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper explains how mine operators are taking a closer look at the power of explosives and how primary breakage affects other open-pit mining costs. Slurries have overcome most of the disadvantages attributed to them in their early years and may replace Anfo. Effective blasting is the key to an efficient, low-cost mining operation. Reviews are presented on research in crater studies, computer-aided design, the expanding gas theory, and high-speed motion picture cameras that show the importance of shock energy in fracturing the rock interfaces throughout the burden. The paper concludes with MSHA-approved courses in blasting offered throughout the US.

Energy Technology Data Exchange (ETDEWEB)

In the context of the shock-initiation problem, we study analytically the first effects of chemistry, treating a small chemical heat release as a perturbation on an inert flow. Specifically, we study the initial transient in plane-shock initiation in a dilute explosive, where the chemical energy is small relative to the mechanical-thermal energy. The vehicle for the study is the mathematical analog for reactive flow. The solution resembles a double refraction: to first order, the pressure or density is a superposition of two forward-going waves, both originating at the rear boundary, and carrying the same function, but running at different velocities. Surprisingly, this first-order solution is independent of the sensitivity of the reaction rate to the state, which appears only at second order.

Energy Technology Data Exchange (ETDEWEB)

In the early 1970s Yang and Menichelli demonstrated that direct laser illumination of low-density secondary explosive prr:ssings through a transparent window could produce detonation. 'The energy requirement for threshold initiation of detonation was reduced when a thin metal coating of metal covered the side of the window against which the low-density explosive was pressed. We have obtained experimental results that are in general agreement with the results of Renllund, Stanton and Trott (1 989) and recent: work by Nagayama, hou and Nakahara (2001). We report exploration of the effects of laser beam diameter, PEiTN density and specific surface area, and thickness of a titanium coating on the window.

Energy Technology Data Exchange (ETDEWEB)

This document provides stakeholder evaluations on innovative technologies to be used in the remediation of volatile organic compounds from soils and ground water. The technologies evaluated are; in-well vapor stripping, in-situ bioremediation, and gas membrane separation.

Energy Technology Data Exchange (ETDEWEB)

This project dealt with use of condensing heat exchangers to recover water vapor from flue gas at coal-fired power plants. Pilot-scale heat transfer tests were performed to determine the relationship between flue gas moisture concentration, heat exchanger design and operating conditions, and water vapor condensation rate. The tests also determined the extent to which the condensation processes for water and acid vapors in flue gas can be made to occur separately in different heat transfer sections. The results showed flue gas water vapor condensed in the low temperature region of the heat exchanger system, with water capture efficiencies depending strongly on flue gas moisture content, cooling water inlet temperature, heat exchanger design and flue gas and cooling water flow rates. Sulfuric acid vapor condensed in both the high temperature and low temperature regions of the heat ...

Energy Technology Data Exchange (ETDEWEB)

Measurements of the double-electron-capture process in which a positive ion of iodine becomes a negative ion in a single collision with a magnesium atom are reported between 20 and 90 keV. The cross section is comparable to that for the rare gases and not as large as might be expected from a two-valence-electron atom. This process is probably insignificant in the production of negative ion beams using a magnesium-vapor target.

Energy Technology Data Exchange (ETDEWEB)

The adsorption of mercury vapor on particles was studied by using soot particles generated by incineration of sewage sludge (EP-ash) and activated carbon particles. Through the experiments, it was found that, at 298 K, the EP-ash has a fairly high adsorption capacity for mercury vapor in the order of 10/sup -6/g/g, which is between that of the ordinary soils and that of activated carbon particles. Furthermore, it was found that physical adsorption of mercury vapor on the studied particles at high temperature is described by Dubinin's equation. On the basis of the equation, it was shown that EP-ash physically adsorbs very little mercury at high temperature, and therefore, most mercury in the EP-ash is chemically adsorbed or contained in a form of mercury compounds. Nevertheless, the total amount of mercury contained in the particles is very little compared to the total mercury in the exhaust gases so that most ...

Energy Technology Data Exchange (ETDEWEB)

The process operation of the hot wall vapor deposition method, formation of dry organic thin film and the control of molecular arrangement were described. This equipment included a substrate on the upper end of the hot wall tube and the vapor source at the lower end. The remarkable features are the hot wall tube which plays the role to hold vaporizing molecules to the high temperature and to transport molecules, and the flip flop mechanism which gives some idle period for the molecular vaporization by shutter closing. Several experiments were carried out by using stearic acid and by changing the distance S from the upper end of hot wall quartz tube to the substrate, the furnace temperature T{sub f} and the substrate temperature T{sub s}. When T{sub f} is equal to or less than the melting point of stearic acid, molectles are preferentialy made to vertical arrangement. In the case of T{sub f} more than ...

International Nuclear Information System (INIS)

The authors present a state-of-the-art review of natural circulation heat transfer in loop type reactor plants. Most of the examples are taken from Fast Flux Test Facility (FFTF) design experience, drawing on the authors' familiarity and a developing base of available documentation. On-going studies related to the Clinch River Breeder Reactor (CRBR) and some foreign experience are also noted where available in the literature. The emphasis is on the role of natural circulation in decay heat removal; however, free convection during either operation at power or normal shutdown does influence some aspects of the design and these are reviewed. In treating decay heat removal the topics discussed include steady state loop performance and transient dynamics for conditions immediately after scram and for the longer term which involves different considerations. The review summarizes complex dynamics, specific to the FFTF design evaluation, which particularly illustrate large available margins ...

International Nuclear Information System (INIS)

Research is in progress to obtain a satisfactory creep ductility for alloy 800 when used as heat exchanger material in sodium-cooled fast reactors (LMFBR). The creep test characteristics at present available show that a pronounced tendency to reduced elongation by creep failure may arise after prolonged testing in the 500-700 deg C temperature range. This phenomenon is now agreed to be primarily inherent to the conditions for Ni_3(Ti,Al) precipitation in the material and hence to the Ti and Al concentrations. By structural studies and hardness measurements on material subjected to creep tests and taken from a large number of castings, the relationship was established between the (Ti+Al) content and the structural hardness effect of Ni_3(Ti,Al) at 600 deg C. Below a certain Ti+Al concentration, no precipitation occurs and hence the creep ductility to failure can be improved considerably by limiting the allowed Ti+Al content in the material, though at the price of ...

Energy Technology Data Exchange (ETDEWEB)

Real-time neutron radiography has been used to study the dynamic behavior of two-phase flow and measure vapor fractions in a steam-water duct at atmospheric pressure. This unique experimental technique offers one the opportunity to observe and record on videotape now Patterns and transient behavior of two-phase flow inside opaque containers without perturbing the environment. The neutron radiographic technique is non-intrusive and requires no special transparent window region. Data are recorded simultaneously over a large area of interest. Image processing of the video data can be employed to measure bubble velocities and time-averaged and Instantaneous vapor fractions.

Science.gov (United States)

We present a numerical model of vapor-dominated reservoirs which is based on the well-known conceptual model of White, Muffler, and Truesdell. Computer simulations show that upon heat recharge at the base, a single phase liquid-dominated geothermal reservoir in fractured rock with low matrix permeability will evolve into a two-phase reservoir with B.P.D. (boiling point-for-depth) pressure and temperature profiles. A rather limited discharge event through cracks in the caprock, involving loss of only a few percent of fluids in place, is sufficient to set the system off to evolve a vapor-dominated state. The attributes of this state are discussed, and some features requiring further clarification are identified. 26 refs., 5 figs.

Energy Technology Data Exchange (ETDEWEB)

A study was made of employee exposure to oil sludge and vapors during oil-sludge removal and maintenance activities at the Alyeska Pipeline Service Company's Ballast Water Treatment Facility, Valdez, Alaska. Total hydrocarbons, except benzene, toluene, and xylene, showed concentrations from 371 to 1228mg/m3. Of eight maintenance workers, five reported headache, dizziness, or nausea when working without a respirator. The authors conclude that workers were potentially exposed to benzene vapors and total hydrocarbon vapors exceeding the evaluation criteria for these substances. The authors recommend the use of respiratory protection measures to reduce exposures during work operations.

Science.gov (United States)

Using the infrared spectroscopy method, we have studied the effect of thermal dehydration (under vacuum and in air) and treatment with water vapor on the acid centers of very high silicon zeolites of the ZSM type. We have shown that dehydration under vacuum and in air completely and irreversibly removes the OH groups at 1120/sup 0/K, while treatment with water vapor removes these groups at 770/sup 0/K. The Lewis acid centers of dehydrated zeolites (represented by two types of centers) are more heat-stable than the Bronsted acid centers, but the vapor treatment at 1020/sup 0/K leads to the disappearance of the Lewis acid centers. In this work, we discuss the reasons for destruction of the acid centers of the zeolites under different treatment conditions.

Energy Technology Data Exchange (ETDEWEB)

Anti-reflective coatings made with Teflon AF2400 had the highest damage thresholds recorded for physical vapor deposited coatings at the Lawrence Livermore National Laboratory damage facility. Physical vapor deposited layers of Teflon AF2400, a perfluorinated amorphous polymer, maintained the bulk optical properties of a high transmittance from 200 nm to 1600 nm, and a low refractive index. In addition, the refractive index can be intentionally reduced by control of two common deposition parameters, deposition rate and substrate temperature. Scanning electron microscopy and nuclear magnetic resonance observations indicated that morphological changes caused the variations in the refractive index rather than compositional changes. The coatings adhered to fused silica and silicon wafers under normal laboratory handling conditions.

International Nuclear Information System (INIS)

This study concerns mixtures of triacetone triperoxide (3,3,6,6,9,9-hexamethyl-1,2,4,5,7,8-hexoxonane, TATP) and ammonium nitrate (AN) with added water (W), as the case may be, and dry mixtures of TATP with urea nitrate (UN). Relative performances (RP) of the mixtures and their individual components, relative to TNT, were determined by means of ballistic mortar. The detonation energies, E_0, and detonation velocities, D, were calculated for the mixtures studied by means of the thermodynamic code CHEETAH. Relationships have been found and are discussed between the RP and the E_0 values related to unit volume of gaseous products of detonation of these mixtures. These relationships together with those between RP and oxygen balance values of the mixtures studied indicate different types of participation of AN and UN in the explosive decomposition of the respective mixtures. Dry TATP/UN mixtures exhibit lower RP than analogous mixtures TATP/AN containing up to 25% of ...

CERN Document Server

The collapse of a massive star's core, followed by a neutrino-driven, asymmetric supernova explosion, can naturally lead to pulsar recoils and neutron star kicks. Here, we present a two-dimensional, radiation-hydrodynamic simulation in which core collapse leads to significant acceleration of a fully-formed, nascent neutron star (NS) via an induced, neutrino-driven explosion. During the explosion, a ~10% anisotropy in the low-mass, high-velocity ejecta lead to recoil of the high-mass neutron star. At the end of our simulation, the NS has achieved a velocity of ~150 km s$^{-1}$ and is accelerating at ~350 km s$^{-2}$, but has yet to reach the ballistic regime. The recoil is due almost entirely to hydrodynamical processes, with anisotropic neutrino emission contributing less than 2% to the overall kick magnitude. Since the observed distribution of neutron star kick velocities peaks at ~300-400 km s$^{-1}$, recoil due to ...

CERN Document Server

We present a theoretical framework for formal study of systematic effects in Supernovae Type Ia (SN Ia) that utilizes 2-d simulations to implement a form of the deflagration-detonation transition (DDT) explosion scenario. The framework is developed from a randomized initial condition that leads to a sample of simulated SN Ia whose Ni56 masses have a similar average and range to those observed, and have many other modestly realistic features such as the velocity extent of intermediate mass elements. The intended purpose is to enable statistically well-defined studies of both physical and theoretical parameters of the SN Ia explosion simulation. We present here a thorough description of the outcome of the SN Ia explosions produced by our current simulations. A first application of this framework is utilized to study the dependence of the SN Ia on the Ne22 content, which is known to be directly influenced by the progenitor ...

CERN Document Server

Gamma-Ray Bursts (GRBs) are thought to originate at cosmological distances from the most powerful explosions in the Universe. If GRBs are not beamed then the distribution of their number as a function of gamma-ray flux implies that they occur once per (0.3-40) million years per bright galaxy and that they deposit >10^{53} ergs into their surrounding interstellar medium. The blast wave generated by a GRB explosion would be washed out by interstellar turbulence only after tens of millions of years when it finally slows down to a velocity of 10 km/s. This rather long lifetime implies that there could be up to several tens of active GRB remnants in each galaxy at any given time. For many years, radio observations have revealed the enigmatic presence of expanding neutral-hydrogen (HI) supershells of kpc radius in the Milky Way and in other nearby galaxies. The properties of some supershells cannot be easily explained in terms of conventional ...

Energy Technology Data Exchange (ETDEWEB)

Previous analyses of binary cycles for conversion of geothermal energy from moderate temperature resources to electrical energy have shown potential gains in net geofluid effectiveness on the order of 8%, resulting from selection of turbine-expansion processes whose equilibrium states pass through the two-phase region. If condensation occurs, this gain could be reduced or eliminated by the resulting loss in turbine efficiency. Experience with many fluids, however, indicates that vapor supersaturation permits metastable pure-vapor states to exist at temperatures considerably below the saturation temperature at a given pressure; thus, by better understanding the condensation process, and properly structuring the cycle, substantial performance gains may be possible. The purpose of the present study was to assess the probability for attaining this performance gain by estimating the extent of condensation which might be expected during such an ...

Energy Technology Data Exchange (ETDEWEB)

The excellent high temperature strength and thermal conductivity of molybdenum-base alloys provide attractive features for components in advanced magnetic and inertial fusion devices. Refractory metal alloys react readily with oxygen and other gases. Oxidized molybdenum in turn is susceptible to losses from volatile molybdenum trioxide species, MoO{sub 3}(m), in air and the hydroxide, MoO{sub 2}(OH){sub 2}, formed from water vapor. Transport of radioactivity by the volatilization, migration, and re-deposition of these volatile species during a potential accident involving a loss of vacuum or inert environment represents a safety issue. In this report the authors present experimental results on the oxidation, volatilization and re-deposition of molybdenum from TZM in flowing air between 400 and 800 C. These results are compared with calculations obtained from a vaporization mass transfer model using chemical thermodynamic data for ...

Energy Technology Data Exchange (ETDEWEB)

Soil vapor extraction (SVE) is a widely accepted in-place treatment technology that uses forced air to remove contaminant vapors from zones of permeable vapor flow, thereby enhancing the volatilization of contaminants from the subsurface. The resulting off-gases are contaminated with volatiles and semi-volatiles and have to treated by catalytic or thermal destruction systems, activated carbon adsorbers, or bioreactors. Of these, activated carbon adsorption is the most commonly used technology. From the theoretical foundation of SVE and carbon adsorption, two nomographs were developed for remedial investigation, feasibility studies, planning, operation, and preliminary design purposes. An advantage of such nomographs is that they graphically indicate the sensitivity of the remediation process to different design parameters and critical ranges within a given parameter. In effect, nomographs can help to foster an intuitive ...

Science.gov (United States)

Some vapor-dominated geothermal reservoirs and low-permeability gas reservoirs exhibit anomalous behavior that may be caused by surface adsorption. For example, geothermal reservoirs in the Larderello area of Italy and reservoirs in the Geysers Geothermal...

Energy Technology Data Exchange (ETDEWEB)

There are certain factors to take into account when determining the suitability of a healthy house site. Power lines, agricultural spraying, vehicle exhaust, and industrial pollution are all potential sources of indoor air contamination. It is recommended that a environmental assessment be done to determine whether there are specific sources of contamination. Good drainage is required. The surrounding landscaping should be open and sunlit, and with low maintenance requirements. Decks and fences made from pressure-treated or chemical treated lumber should be avoided. One of the early decisions in the design process is the choice of the structural system. The key with all foundation types is to control moisture, whether from rain, from the ground, or the condensation of moisture from the air with cooling. The construction frame is sealed away from the occupants by the air/vapor barrier, so only in extreme cases is it essential to use alternatives to softwood lumber ...

Science.gov (United States)

Feb 15, 2008 ... hydrological properties (e.g., hydrometeor budgets, cloud ice/water, transports ... cloud fraction, mass and particle size. In combination, these .... anomaly in the LS is not simply due isentropic movement of water vapor relative ...

Energy Technology Data Exchange (ETDEWEB)

The chemical operational concept originally established for the water-steam circuit of Angra II nuclear power plant has undergone several modifications throughout the development of the project. This work discusses the two main modifications giving special attention to the costs involved and analyses the main points and the consequences of such modifications 1 ref., 4 figs., 2 tabs.

DEFF Research Database (Denmark)

The thermodynamic framework that was developed in a previous work [Vrachnos et al. Ind. Eng. Chem. Res. 2004, 43, 2798] for the description of chemical and vapor-liquid equilibria of carbon dioxide, hydrogen sulfide, and their mixtures in aqueous methyldiethanolamine (MDEA) solutions is revised and extended in this study to the absorption of carbon dioxide into aqueous monoethanolamine (MEA) solutions and aqueous MDEA-MEA blends. The results of the model are compared with experimental data taken from the literature. Very satisfactory predictions of acidic gas vapor-liquid equilibrium over MDEA, MEA, and their blends at various concentrations, acidic gas loadings, and temperatures are obtained.

Energy Technology Data Exchange (ETDEWEB)

The production of polarized negative ion beams by collisional pumping is described. Collisional pumping utilizes repeated charge changing collisions in a thick electron-spin-polarized gas or vapor target to form a polarized fast atom beam. The polarized fast atom beam is then partially converted into a polarized negative ion beam in a vapor target. Analysis is presented for a hydrogen beam passing through either a thick polarized H atom target or a thick polarized alkali target. Large polarizations and large currents may be possible.

Science.gov (United States)

Plasma generated in low-density vapor by a negative ion beam has been studied experimentally and computationally. We show that space charge neutralization of the beam occurs at very low vapor density, and that correspondingly the electron density may be much less than the beam and plasma ion densities. When there is a large local gas density, as in a charge changing cell, the resulting high electron density is also localized to the same region. Therefore, very few electrons will reach a negative ion accelerator even if it is placed one or two beam diameters from such a cell.

International Nuclear Information System (INIS)

A thermodynamic model was used to estimate enthalpy of solution of carbon dioxide (CO_2) in methyldiethanolamine (MDEA) aqueous solutions. The model was based on a set of equations for chemical equilibria, phase equilibria, charge, and mass balances. Non-ideality in the liquid phase was taken into account by interaction parameters fitted to (vapor + liquid) equilibrium data. The enthalpies of solution of CO_2 were derived from the model using classical thermodynamic relations and were compared to experimental values obtained in previous works.

Energy Technology Data Exchange (ETDEWEB)

In this paper the diffusion of tritiated water vapor into concrete walls is studied to evaluate tritiated water retention capacity of a fusion reactor concrete building. Using a model of the tritiated water diffusion determined form experimental results, depth profiles of tritiated water in concrete are calculated in the case of being exposed to air containing tritiated water vapor during the normal operational condition of a fusion reactor. A 0.5-m-thick concrete is sufficient for reactor hall walls from a viewpoint of the tritium containment.

Energy Technology Data Exchange (ETDEWEB)

Analyses have been made of gases in clouds apparently emanating from Mount Saint Helens. Despite appearances, most of the water in these clouds does not issue from the volcano. Even directly above a large fumarole deltaD and delta/sup 10/O data indicate that only half the water can come from the volcano. Isotopic and chemical evidence also shows the steam in the volcano (-33.0 per mol deltaD) from which a condensate of 0.2 N HCl was obtained is not a major cause of the explosions. The steam in the volcano is derived from a metamorphic brine in the underlying Tertiary meta andesite. The gas that caused the explosive eruptions is carbon dioxide.

Energy Technology Data Exchange (ETDEWEB)

Studies technological safety of installing a water spray pressure vessel between electrostatic dedusters and coal sludge ducts. These sprays are in use elsewhere for steam generator ash removal. Dust ignition and explosion tests were carried out to examine flame and pressure wave propagation through the vessel into ducts. Water jet diameter, amount of water sprayed and coal dust removed were varied. Pressure waves exceeded 250 Pa. Test results show the vessel to be suitable for installation in briquetting plants due to its flame and explosion barrier effect and extermination of smoldering dust fires. The only disadvantage of the vessel is seen as its water and electric power consumption; about 8/sup 3//h of water and 1.5 kW/h of power per vessel serving dedusters of a 2,200 m/sup 2/ rotary brown coal dryer.

British Library Electronic Table of Contents (United Kingdom)

The results of following the oxidative degradation of a plastic-bonded explosive (PBX 9501) are reported. Into over 1100 sealed containers were placed samples of PBX 9501 and combinations of its components and aged at relatively low temperatures to induce oxidative degradation of the samples. One of the components of the explosive is a poly(ester urethane) polymer and the oxidative degradation of the samples were following by measuring the molecular weight change of the polymer by gel permeation chromatography (coupled with both differential refractive index and multiangle laser light scattering detectors). Multiple temperatures between 40 and 64 degreeC were used to accelerate the aging of the samples. Interesting induction period behavior, along with both molecular weight increasing (cro...

British Library Electronic Table of Contents (United Kingdom)

Abstract Copy number variants (CNVs) are known to be associated with complex neuropsychiatric disorders (e.g., schizophrenia and autism) but have not been explored in the isolated features of aggressive behaviors such as intermittent explosive disorder (IED). IED is characterized by recurrent episodes of aggression in which individuals act impulsively and grossly out of proportion from the involved stressors. Previous studies have identified genetic variants in the serotonergic pathway that play a role in susceptibility to this behavior, but additional contributors have not been identified. Therefore, to further delineate possible genetic influences, we investigated CNVs in individuals diagnosed with IED and/or personality disorder (PD). We carried out array comparative genomic hybridizati...

British Library Electronic Table of Contents (United Kingdom)

There is little flame spread data for homogeneous energetic materials and no data for nitramines. We report the results of flame spread experiments of PBX 9501 (HMX (cyclotetramethylenetetranitramine) based explosive). The horizontal flame spread rate, Sf, is of the same order of magnitude as normal deflagration and varies nearly as the square root of pressure, as our scaling analysis presented here predicts. In the vertical orientation, the flame propagation downward was observed to be slightly faster than horizontal flame spread, presumably because of the melt layer flowing downward on the sample. In an accident scenario, a charge may be fractured or the surface roughened. Consequently, we also examined the effect of roughness. Minor roughness created by explosives machining was found to...

Energy Technology Data Exchange (ETDEWEB)

The optimization of the safety characteristics of electrical installations in industrial plants with explosion or fire hazards can be obtained only through a careful interdisciplinary study and analysis carried out at the onset of the plant project design phase. The least complex and costly and safest solutions are those which are born from plant designs which take into account the typology of the industrial process or technology, or which incorporate pollution abatement measures and adequate safety measures for the electrical installations. This paper provides examples to illustrate how the global plant economy is fundamentally dependant upon a multi-disciplinary initial effort in design analyses. Comments are made relevant to the adequacy of the safety requirements established by existing and planned Italian norms in dealing with safety and fire protection for high-tech industrial plant electrical installations.

Energy Technology Data Exchange (ETDEWEB)

Accelerated aging tests on gold bridgewired detonator assemblies to determine compatibility of the Au and Pd-In-Sn solder with the organic explosive, PENT, have revealed an unusual corrosion process. These tests, conducted at 74/sup 0/C and 54/sup 0/C indicated a preferential attack of the gold. A matrix of corrosion test units was established to study this corrosion problem with accelerating temperatures up to 100/sup 0/C. Scanning electron microscopy (SEM), energy dispersive x-ray (EDX), and x-ray diffraction techniques were used to determine the extent of the corrosion and identify the corrosion products. Results indicate the preferential attack of the gold was due to HCN formed by decomposition of the explosive powder (PETN) at high temperatures. Other associated reactions were also observed including subsequent attack of the solder by the gold corrosion product and degradation of the plastic header.

Energy Technology Data Exchange (ETDEWEB)

An analytical model is proposed for the design and simulation of in-situ fracture of deep oil sand formations. This model is based on the finite element variational principle in conjunction with special empirical modules to characterize in-situ oil sands behavior. A computer code by the name of SANFRAC was developed to handle the dynamic fracture of formations induced by explosives. Simulation of hydraulic fracture processes can be treated by the same code as special cases using the quasi-static analysis. Numerical case studies by the SANFRAC code indicate that extensive horizontal fracture can be achieved by dynamic loads with proper fracture starters configured at the injection well. The unique advantage of the dynamic fracturing technique over the hydraulic fracture methods is also demonstrated by these studies.

International Nuclear Information System (INIS)

The irradiation of air produces some toxic gases such as ozone, nitric oxide, nitrogen dioxide, nitrogen trioxide, nitrogen tetroxide, nitric anhydride and nitrous oxide. Of these gases, ozone is the most important because of its toxicity and may be produced in such quantities as to constitute a health hazard within the irradiation room. The toxicity, and explosive characteristics of ozone and quantitative aspects of ozone production are discussed and ventilation requirements considered. (U.K.).

Energy Technology Data Exchange (ETDEWEB)

The problem on change of deuterium abundance in the process of galactic evolution (star evolution, supernova explosions, nucleosynthesis in supermassive objects) is considered. It is shown that the observable deuterium quantity in the interstellar medium must correspond to its cosmological abundance. This conclusion is independent of the rate of accretion of intergalactic gas by Galaxy. The effect of hypothetical pregalactic active objects on cosmological deuterium is small. It is poind out that observations of interstellar deuterium in absorbtion at lambda=91.6 cm are significant.

British Library Electronic Table of Contents (United Kingdom)

The electrophysical characteristics of the electric cable?s transition into a state of a heterogenic polymer system due to a wire?s explosion were examined. Using cyclic heating-cooling of the composite, the changes in its topology were observed. The latter makes it possible to regulate the dielectric characteristics of the system.

Science.gov (United States)

Detonators are used to convert electrical or other energy into an explosive output. This output can then be used to initiate further explosive charges. To aid in the development of explosive systems, it is important to characterize the output of detonators, in particularly the pressure produced. Recent advances over the last five years in high-speed digitizing oscilloscopes and high-bandwidth photodiodes, driven primarily by the telecommunications industry, have enabled the development of a new type of interferometer for measuring high velocities, such as those found in detonics experiments. The Photonic Doppler Velocimeter (PDV) can be visualized as a fiber-based Michelson interferometer. The light from a single-mode fiber laser at 1550 nm is passed through a circulator, which acts to separate bi-directional light. The beam is then reflected via free-space optics off the surface of interest, and then focused back into the ...

Energy Technology Data Exchange (ETDEWEB)

A study by the U.S. Air Force School of Aerospace Medicine, Brooks AFB, Texas, has compared the shelter processing transfer of chemical warfare agent simulant vapor for subjects wearing unwashed and laundered ground-crew chemical defense overgarments. Twice laundered and four times laundered protective garments were included in the assessment. Test subjects, wearing the unwashed and laundered protective garments were initially sprayed with liquid simulant (methyl salicylate) to a target density of 5 g m-2. They were then sequentially processed into and through the USAFSAM Collective Protection Shelter (SCPS-2B) test facility. Immediately upon entry to the Toxic-Free Area, the subjects were confined in individual off gassing booths for 2 h while offgassed simulant vapor concentration in the booths was recorded. The resulting mean maximum vapor concentrations recorded in the booths for subjects who had worn unwashed and ...

Energy Technology Data Exchange (ETDEWEB)

Data which have been collected by Los Alamos National Laboratory waste management for the hydrologic characterization of the subsurface at the low level radioactive waste disposal facility, Area G, are reported and discussed briefly. The data includes Unsaturated Flow Apparatus measurements of the unsaturated conductivity in samples from borehole G-5. Analysis compares these values to the predictions from van Genuchten estimates, and the implications for transport and data matching are discussed, especially at the location of the Vapor Phase Notch (VPN). There, evaporation drives a significant vapor flux and the liquid flux cannot be measured accurately by the UFA device. Data also include hydrologic characterization of samples from borehole G-5, Area G surface soils, Los Alamos (Cerros de Rio) basalt, Tsankawi and Cerro-Toledo layers, the Vapor Phase Notch (VPN), and additional new samples from the uppermost tuff layer at ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents the performance analysis on a hybrid air-conditioning system according to the hybrid building energy system of the green building demonstration project in Shanghai, in which a 150 m{sup 2} solar collector is used to power two 10 kW adsorption chillers, a vapor compression heat pump is used to cool air in the evaporating end while the condensing heating at about 80{sup o}C is fully used to regenerate a liquid desiccant dehumidification system. In the hybrid system, the sensible cooling to the air is treated mainly by solar adsorption cooling and vapor compression cooling, whereas the latent heat is treated by the liquid desiccant dehumidification system with regeneration from the condensing heat of the heat pump. The results show that the performance of this system is 44.5% higher than conventional vapor compression system at a latent load of 30% and this improving can be achieved by 73.8% at a 42% latent ...

Energy Technology Data Exchange (ETDEWEB)

The three-dimensional (3-D), multiphase, computational fluid dynamic (CFD) code FLUENT is used to simulated two-phase flow behaviour in a CANDU header manifold under low (natural circulation) flow conditions. This behaviour was previously inferred from experimental data. The CFD simulations reported here are being used to support these inferences and to obtain a better understanding of phase distribution in the header manifold. The simulations seem to show that the vapor-water mixture models in the FLUENT code do not capture properly phase separation in the header and proper phase branching at the header-feeder connections that have been observed in experiments at low flows. The simulations using discrete-phase model in FLUENT, which tracks the pathlines of the individual vapor bubbles in the water continuum phase, show interesting, complicated and, in some cases, unexpected bubble trajectories from the point of injection of the bubbles at a ...

Science.gov (United States)

Continuous wave operation of an Al/sub 0.21/Ga/sub 0.31/In/sub 0.48/P /Ga/sub 0.52/In/sub 0.48/P /Al/sub 0.21/Ga/sub 0.31/In/sub 0.48/P double heterostructure (DH) laser diode was achieved for the first time at 77 K. The device was made from a DH wafer grown by atmospheric metalorganic chemical vapor deposition using triethyl metals and phosphine as source materials. At 77 K, the lasing wavelength was 0.653 ..mu..m and the threshold current was 55 mA for a diode with a nitride-insulated, 8-..mu..m-wide and 250-..mu..m-long stripe geometry.

Energy Technology Data Exchange (ETDEWEB)

A solar energy desalination process utilizing solar radiation directly for the evaporation of salt water is described. Ambient air takes on water vapor as the air passes through an evaporative medium. It is then directed between a saline water-covered, solar absorbing surface and a solar collecting housing. The resulting heated and moisture-saturated air is cooled in a heat exchange means where condensation of fresh water occurs. Simultaneously, cool salt water is utilized as the cooling water in the heat exchange means, and takes on the heat of condensation given up by the condensing vapor. The heated salt water from the heat exchange means is partially directed over the solar absorbing surface, and at least a portion of it is also directed to wet the evaporative medium. Several optional sub-processes are described for operation of the system during periods of reduced insolation, and an alternative process is described for operation of the ...

Energy Technology Data Exchange (ETDEWEB)

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for vapor samples obtained during the operation of mixer pumps in tank 241-AZ-101. The primary purpose of the mixer pump test (MPT) is to demonstrate that the two 300 horsepower mixer pumps installed in tank 241-AZ-101 can mobilize the settled sludge so that it can be retrieved for treatment and vitrification. Sampling will be performed in accordance with Tank 241-AZ-101 Mixer Pump Test Data Quality Objective (Banning 1999) and Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis (Mulkey 1999). The sampling will verify if current air emission estimates used in the permit application are correct and provide information for future air permit applications.

International Nuclear Information System (INIS)

Selective formation of ZnO nanodots was accomplished by metalorganic chemical vapor deposition on nanopatterned SiO_2/Si substrates. Self-organized ZnO nanodots were selectively formed in nanopatterned lines of Si created by etching of SiO_2 with focused ion beam (FIB), whereas any nanodots were hardly observed on the SiO_2 surface in the vicinity of the FIB-sputtered Si areas. The mechanism of the selective formation of ZnO nanodots on FIB-nanopatterned lines is mainly attributed to the effective migration of Zn adatoms diffusing on the SiO_2 surface into the Si lines followed by the nucleation at surface atomic steps and kinks created by Ga"+ ion sputtering. Cathodoluminescence measurements confirmed that the emission originated from the selectively grown ZnO nanodots.

Energy Technology Data Exchange (ETDEWEB)

The photocatalyzed degradation of pyridine in the gas phase was investigated using titanium dioxide semiconductor supported on mordenite. The complete mineralization was found to occur over a catalyst containing 75 wt% TiO{sub 2} and 25 wt% mordenite in about 180 min in the presence of saturated water vapor at O{degrees}C (4.6 Torr). Low water vapor pressure of 0.096 Torr was found to be sufficient to achieve a reasonably high percentage and rate of degradation. Diffusion of pyridine within the catalyst adversely affects the activity when the thickness of the catalyst coating exceeds the penetration depth of illumination. The activity of the zeolite-supported catalysts was higher than that of TiO{sub 2}. The photonic efficiency for the complete mineralization of pyridine to CO{sub 2} was determined to be 0.48. 29 refs., 6 refs., 1 tab.

International Nuclear Information System (INIS)

The metallo-organic chemical vapor deposition (MOCVD) process has been used with great success to grow AlGaAs-GaAs and InGaAsP-InGaAs-InP heterostructure materials for electronic and optoelectronic applications. Devices fabricated from Al/sub x/Ga/sub 1-x/As-GaAs heterostructures grown by MOCVD include bipolar transistors, field-effect transistors (FETs), high-mobility (or modulation-doped) FETs, large-area high-efficiency solar cells, low-threshold lasers, high-power lasers, quantum-well lasers, and visible lasers. The state of the art for the MOCFD growth of optoelectronic devices is reviewed in this paper, and some comments are made regarding future trends in the growth of these materials by MOCVD.

British Library Electronic Table of Contents (United Kingdom)

We have studied the nature of continuum emitted in the visible spectral range from a noncontracted positive column of discharge in a cesium vapor-xenon mixture at a pressure of 45 Torr and at a degree of ionization below 3 ? 10?6. The main contribution to the continuous emission under such conditions is due to electron-xenon atom bremsstrahlung. The intensity of emission has been experimentally and theoretically studied as a function of the electric field strength and electron density in the positive column. It is established that an increase in the visible emission intensity with the electric field strength is related to an increase in the number of hot electrons in plasma.

Energy Technology Data Exchange (ETDEWEB)

Vapor-liquid equilibria, by head-space gas-chromatographic analysis of the equilibrated vapor phase directly withdrawn from the equilibration apparatus, and molar excess volumes, V[sup E], by means of a vibrating-tube densimeter, of binary mixtures containing thiaalkanes or dithiaalkanes with n-alkanes or cyclohexane, were determined at 298.15 K. The excess molar Gibbs free energies, GE, of the examined mixtures were obtained by a least-squares treatment of the equilibrium data. The GE and V[sup E] values indicate that the steric effect exerted by the alkyl groups adjacent to the S group causes a regular decrease of the G[sup E] (or V[sup E]) with increasing the number of alkyl groups in the thiaalkane. A tentative approach, based on an additivity scheme of surface interactions combined with the scaled particle theory, is presented to estimate the energies of solvation in terms of group contributions.

CERN Document Server

The concept of the 'white-light cavity' has recently generated considerable research interest in the context of gravitational wave detection. Cavity designs are proposed using negative (or anomalous) dispersion in an intracavity medium to make the cavity resonate over a large range of frequencies and still maintain a high cavity build-up. This paper presents the first experimental attempt and demonstration of white-light effect in a meter long ring cavity using an intracavity atomic medium. The medium's negative dispersion is caused by bi-frequency Raman gain in an atomic vapor cell. Although the white light condition was not perfectly achieved and improvements in experimental control are still desirable, significantly broad cavity response over bandwidth greater than 20 MHz has been observed. These devices will have potential applications in new generation laser interferometer gravitational wave detectors.

Energy Technology Data Exchange (ETDEWEB)

The Lawrence Livermore National Laboratory has developed a mobile field laboratory for remote measurement of atmospheric processes and observables that are important in global climate change, dispersal of hazardous materials, and atmospheric pollution. Specific observables of interest are water vapor, trace gases, aerosol size and density, wind, and temperature. The goal is to study atmospheric processes continuously for extended periods in remote field locations. This laboratory has just reached field ready status with sensors for aerosol and trace gas measurement based on established techniques. A development program is underway to enhance the sensor suite with several new techniques and instruments that are expected to significantly extend the state of the art in remote trace gas analysis. The new sensors will be incorporated into the lab during the next two years.

International Nuclear Information System (INIS)

An experiment was performed with a mock-up of the core of the Fast Flux Test Facility (FFTF) reactor to evaluate three reactivity measurement methods for application to liquid-metal fast breeder reactors (LMFBR): modified source multiplication measurements with the low-level flux monitor for refueling (35 dollars subcritical) of FFTF, noise analysis to 35 dollars subcritical, and inverse kinetics rod drop to 12 dollars subcritical. To investigate the spatial dependence of these measurement methods and to resolve discrepancies previously reported, detectors were placed in the core, reflector, and radial shield, and experimental data were collected with the reactivity at near delayed criticality to 35 dollars subcritical. Conclusions from this experiment are the following. Low-level flux monitors in the shield of the FFTF will be adequate for reactivity surveillance during refueling, using the modified source multiplication method calibrated near critical by an ...

Science.gov (United States)

A technical review is presented of experiment activities and state of knowledge on air-borne, radiation source terms resulting from explosive sabotage attacks on spent reactor fuel subassemblies in shielded casks. Current assumptions about the behavior of irradiated fuel are largely based on a limited number of experimental results involving unirradiated, depleted uranium dioxide ''surrogate'' fuel. The behavior of irradiated nuclear fuel subjected to explosive conditions could be different from the behavior of the surrogate fuel, depending on the assumptions made by the evaluator. Available data indicate that these potential differences could result in errors, and possible orders-of-magnitude overestimates of aerosol dispersion and potential health effects from sabotage attacks. Furthermore, it is suggested that the current assumptions used in arriving at existing regulations for the transportation and ...

Energy Technology Data Exchange (ETDEWEB)

Preshocking delays initiation of PBX-9404 and PBX-9501, relative to unshocked material. In PBX-9404 preshock experiments, a first shock of 2.3 GPa was followed 0.65 {mu}s later by a second shock of 5.6 GPa. In PBX-9501, a preshock of 2.8 GPa and 0.32 us duration was followed by an initiating shock of 6.0 GPA. Both PBX explosives show clear desensitization while the preshock persists. In PBX-9404, initiation of detonation occurs nearly as anticipated for the material, after coalescence of the preshock and main shock into a single wave. Multiple embedded magnetic gauges were used to measure the shock histories. Our data indicates a slightly longer run to detonation than expected, even though a single wave is initiating the material. A slight stress reduction at coalescence, as required by the shock dynamics, may be responsible for the overrun. A reactive waste is clearly evident while the preshock persists. The long run to detonation indicates that this reactive wave ...

Energy Technology Data Exchange (ETDEWEB)

This is a prompt report. These days the importance of acquiring knowledge about the structure from the lower crust down to the upper mantle is often discussed with reference taken to Hyogo-ken Nanbu Earthquake. The Hidaka collision belt where the lower crust is exposed on the surface is a rare phenomenon in the world and has been the subject of seismic survey. As a part of the survey, experiments are conducted by the use of vibrations produced by Vibroseis and dynamite sources. Every one of the shot records (20-second record) from the two types of vibration sources contains a clear echo in the vicinity of 16 seconds supposedly from a level deeper than 40 kilometers, not to mention reflections from shallow levels. Although some studies have to be conducted before the reflecting geological boundary (possibly the upper mantle) of the echo near the 16-second point can be identified, yet this is probably the reflection from the deepest level ever obtained in the seismic reflection survey ...

Energy Technology Data Exchange (ETDEWEB)

An analyser for detecting explosives has at least one neutron source and a plurality of gamma ray detectors. An article to be analysed is moved adjacent the source and detectors and is subjected to neutrons which generate gamma rays from any nitrogen in the article. The gamma rays are detected and analysed to determine the nitrogen concentration within the article. In order to achieve an area of uniform detection there are a plurality of detectors equidistant both from the or each source and from the article to be analysed. In order to avoid a decrease in sensitivity away from the source(s) and detectors there may be a second opposing array of source(s) and detectors on the opposite side of the article. For greatest uniformity of detection, a source in one array opposes a detector in the other array and vice versa. Transmission of radiation from the analyser is kept at safe levels by enclosing the analyser within shielding which includes shield members extending ...

International Nuclear Information System (INIS)

High-pressure waterjet equipment is now technically and economically viable and commercially available for the following mining and construction applications: (1) drilling soft to medium-hard rock; (2) slotting, discing, chambering, and reaming in all types of rock. However, additional field experience is needed to prepare detailed economic evaluations. Extensive development of new explosives techniques and blasting methods will be required to take full advantage of the unique waterjet hole slotting, discing, and chambering capabilities.

Energy Technology Data Exchange (ETDEWEB)

In a study of initiations caused by reflected shock from a high-impedance boundary, attempts to establish sufficient conditions for initiative are described. Shock polar analysis is used to discover the ranges of various flow regimes, general shock structures and pressure estimates of states behind the reflected wave. Using this knowledge, wave structure growth rates from hydrocode simulations are estimated and standard-shock initiation criteria are used; experiments are designed in which the initiation from a reflected-shock wave structure appears likely. Two experiments are described in which a reflected-shock wave from a uranium surface initiated PBX 9502. The experimental evidence is in good agreement with the assumptions and results of the analysis.

Energy Technology Data Exchange (ETDEWEB)

The present invention provides a compound of the formula (Cat).sup.+.sub.z[M.sup.++(5-nitro-1H-tetrazolato-N2).sup.-.sub.x(H.sub.2- O).sub.y] where x is 3 or 4, y is 2 or 3, x+y is 6, z is 1 or 2, and M.sup.++ is selected from the group consisting of iron, cobalt, nickel, copper, zinc, chromium, and manganese, and (Cat).sup.+ is selected from the group consisting of ammonium, sodium, potassium, rubidium and cesium. A method of preparing the compound of that formula is also disclosed.

British Library Electronic Table of Contents (United Kingdom)

Theoretical analysis, modeling, and simulation are used to provide insight into the development of permeability during thermal damage of the high explosive PBX 9501. In a recently published article, Terrones et al. [1] conclude that samples of PBX 9501 thermally damaged at 186 degreeC are not permeable to gas flow in a manner consistent with Darcys Law. We disagree with their conclusion. We show that they have misreported data from the literature, and that their argument depends on a fluid flow model that is physically incorrect and is applied with inappropriate physical parameters.

Energy Technology Data Exchange (ETDEWEB)

Measurements were made of the cross section for /sup 242/Am/sup m/ fission induced by neutrons in the energy range 0.04< or =E/sub n/< or =4.52 MeV as well as by neutrons with E/sub n/roughly-equal14.8 MeV. An electrostatic generator and a low-voltage accelerating tube were used to generate the quasimonochromatic neutrons. Measurements in the low-energy region were made by using the time-of-flight technique in neutrons from a nuclear explosion. Results of the measurements are compared with previously published data.

Energy Technology Data Exchange (ETDEWEB)

This plan outlines the procedures and operations used at LLNL's Site 300 for the management of the hazardous waste generated. This waste consists primarily of depleted uranium (a by-product of U-235 enrichment), beryllium, small quantities of analytical chemicals, industrial type waste such as solvents, cleaning acids, photographic chemicals, etc., and explosives. This plan details the operations generating this waste, the proper handling of this material and the procedures used to treat or dispose of the hazardous waste. A considerable amount of information found in this plan was extracted from the Site 300 Safety and Operational Manual written by Site 300 Facility personnel and the Hazards Control Department.

International Nuclear Information System (INIS)

During a hypothetical severe incident in a nuclear power plant with core meltdown a large part of radioactive material is present as aerosol particles in the reactor containment. In current severe accident containment codes the potential influences of hydrogen combustions on the behaviour of aerosols are not considered. Among other effects dry resuspension can increase the aerosol concentration in the atmosphere. Already deposited aerosol material can be re-released into the containment atmosphere by atmospheric currents induced by hydrogen deflagrations or by other phenomena like steam explosions. The objective is to assess the possible influence of this dry resuspension effect on the radioactive source term. (author)

Energy Technology Data Exchange (ETDEWEB)

There have been many recent explosive advances in both IR and Raman spectroscopy which have developed in response to industrial problems of increasing complexity. Probably the biggest factor in these advances has been computerization, which has contributed not only to substantial improvements in data handling but to enormous gains in sensitivities of analyses as well. In this paper numerous examples of Raman and IR applications in industry are given using many of these recent advances, including in-situ techniques, microprobe analyses, unusual combinations of instruments - i.e., hyphenated methods - and new sample handling techniques. The bright future of FT-IR and Raman spectroscopy is also briefly discussed.

British Library Electronic Table of Contents (United Kingdom)

For users and manufacturers affected by unwanted electrostatic discharges, the publication of standards concerning the control of such discharges is a great improvement and helps to prevent unwanted electrostatic discharges in potentially explosive atmospheres as well as around electrostatically sensitive devices. There are, for instance, handbook-like documents giving recommendations to help set up effective electrostatic suppressing measures and programs. Another group of standards focuses on certain products and processes and is, thus, more specific. A third group deals with test methods and specifications to help manufacturers develop products that are safe. It also helps in comparisons with other products and thus meets the customer's real needs. To assist manufacturers and customers ...

Energy Technology Data Exchange (ETDEWEB)

Safety-technical factors related to spontaneous ignition and dust explosions of biomasses were investigated. Parametres of dust explosions and effect of inertisation on the maximum pressure (pmax) and the maximum rate of pressure rise (Kstmax) were studied at elevated initial pressure (1-9 bar). The level of inertisation required to prevent dust explosions totally was determined at different initial pressures. The sensitivity of fuels to spontaneous ignition and the effect of pressure on the sensitivity to and temperature of spontaneous ignition were studied on a pressurised dynamic self-ignition equipment. The effect of inertisation on the self-ignition temperature and alternatives of preventing spontaneous ignition by effective inertisation in the pressure ranges of 1 and 25 bar were investigated. As an example of application, results obtained with the laboratory test equipment were extrapolated to bin sizes used in ...

Energy Technology Data Exchange (ETDEWEB)

With the advance of science, rise of public interest in environmental matters, and continuing erosion of air quality, Federal and state regulators are demanding an increasing complex array of data concerning emissions produced by burning and detonating energetic materials. The US Department of Defense, one of the world`s largest consumers of energetic materials, now must characterize combustion products resulting from open burning/open detonation disposal operations. The catch-all phrase ``below detection limits`` no longer satisfies the regulators who now want testing to delve into the ppt level for volatile organic compounds and ppt level for semivolatile organic compounds. Regulators are also expanding their scope of interest and may soon be asking for emissions data on training operations such as artillery firing. Providing this type of information is no longer an impossibility. The Army, as the single manager of conventional munitions for the three military services, anticipated ...

Energy Technology Data Exchange (ETDEWEB)

This report discusses environmental surveillance activities conducted on the Nevada Test Site during the first calendar quarter of 1996. Surveillance activities included collection and analysis of air, noble gas, tritiated water vapor, and other water samples. Samples were analyzed for both radiological and non-radiological effluents.

CERN Document Server

It is shown that the interpretation of the experimental results reported in the publication "Storage of Light in Atomic Vapor" by D.F.Phillips et al., Phys. Rev.Lett. 86, 783 (2001) [quant-ph/0012138] is incorrect. The experimental observation of this paper can be consistently explained in the framework of standard concepts of the physics of optical pumping and has nothing to do with "storage of light", or "dynamic reduction of the group velocity", or "light pulse compression".

Energy Technology Data Exchange (ETDEWEB)

By means of infrared spectroscopy, x-ray diffraction, and differential thermal analysis, the authors investigate the pyrolysis of dichlorodithiourea cadmium, the vapor phase epitaxy of the cadmium sulfide film, and the composition of the solid and gaseous pyrolysis products. Those products are found to include the thiocyanates of guanidine, ammonium, and hydrogen along with cadmium oxides and sulfates and hydrochloric acid.

Energy Technology Data Exchange (ETDEWEB)

Operational Final Test Report for Integrated Systems, Project W-030 (Phase 2 test, RECIRC and HIGH-HEAT Modes). Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks, including upgraded vapor space cooling and filtered venting of tanks AY101, Ay102, AZ101, AZ102.

International Nuclear Information System (INIS)

Results of calculation of steady thermal-hydraulic characteristics of PVG-440 horizontal steam generator are presented. Steam flows in selected sections are compared to data provided by OKB Gidropress Calculated vapor void fractions are compared to measured ones. (orig.) (3 refs., 3 figs., 8 tabs.).

International Nuclear Information System (INIS)

Radionuclide (R) sorption from a solution (vapor) by freshly formed crystals with production of substitution solid solutions under different types of self-disordering is studied. Changes of self-defectiveness and macrodefectiveness with time and effect of radiation defects in the presence of P macroquantities are taken into account. An analysis for monodispersed sorbents is performed. It is shown that the achievement of equilibrium within a reasonable time in impurity-solid phase system depends on defectiveness which ensures a required level of the coefficient of impurity diffusion in sorbent crystals.

Science.gov (United States)

The U.S. Department of Energy and EPRI have co-funded this project to improve the control of mercury emissions from coal-fired power plants equipped with wet flue gas desulfurization (FGD) systems. The project investigated catalytic oxidation of vapor-pha...

Science.gov (United States)

The report describes tests to demonstrate the feasibility of using a vertical-tube, falling-film, vapor-compression evaporator to concentrate waste water from a flue gas desulfurization (FGD) process. Tests showed that waste water from the Chiyoda FGD process can be concentrated ...

International Nuclear Information System (INIS)

This document generates a supernatant hydroxide ion depletion model based on mechanistic principles. The carbon dioxide absorption mechanistic model is developed in this report. The report also benchmarks the model against historical tank supernatant hydroxide data and vapor space carbon dioxide data. A comparison of the newly generated mechanistic model with previously applied empirical hydroxide depletion equations is also performed.

Energy Technology Data Exchange (ETDEWEB)

We have studied the nucleation and growth processes in a chemical vapor deposition (CVD) diamond film using a tomographic electron backscattering diffraction method (3D EBSD). The approach is based on the combination of a focused ion beam (FIB) unit for serial sectioning in conjunction with high-resolution EBSD. Individual diamond grains were investigated in 3-dimensions particularly with regard to the role of twinning.

Energy Technology Data Exchange (ETDEWEB)

The sequential layer-by-layer adsorption of polyanions and polycations to build polyelectrolyte multilayers has triggered enormous interest in their potential uses in a wide range of fields, from photonic to pharmaceutical applications. We show that the conformation of the solvent swollen films - prior to drying - is determined by the initial adsorption conditions, but can be altered ex-situ by exposure to a liquid phase of very high ionic strength. Recently it has been observed that the swelling depends on the charge of the outermost layer. In the PAH/PSS system we saw that assemblies with PSS as the outermost layer swell more than those with PAH outside. A neutron reflectivity study of this effect in addition indicated the existence of two kinds of water, bound with different strength within the films. Beside an unexpected two-step kinetics of swelling, the reflectivity curves of the layers against vacuum before and after re-hydration in D{sub 2}O vapor did not ...

Energy Technology Data Exchange (ETDEWEB)

AlGaInP epitaxial layers grown at 690 {degree}C by atmospheric pressure organometallic vapor phase epitaxy are investigated by transmission electron microscopy. For the first time, compositionally modulated and ordered structures are simultaneously observed in AlGaInP alloys. The ordering is of the CuPt type with ordering along the {l brace}111{r brace} directions. The ordered regions appear as plate-like microdomains, while the composition modulation takes the form of a fine columnar constrast oriented along the growth direction. In addition, from the results of (001) plan-view diffraction contrast examination, the principal strain direction associated with the modulation structures is found to be perpendicular to the growth direction and lies in the surface plane. Thus, it is concluded that the spinodal decomposition is initiated and developed on the surface during the growth of the AlGaInP epitaxial layers and, finally, forms the columnar structure.

British Library Electronic Table of Contents (United Kingdom)

The electrical characteristics of thin TiO2 films prepared by metal?organic chemical vapor deposition grown on a p-type InP substrate were studied. For a TiO2 film of 4.7?nm on InP without and with ammonium sulfide treatment, the leakage currents are 8.8?10?2 and 1.1?10?4?A/cm2 at +2 V bias and 1.6?10?1 and 8.3?10?4?A/cm2 at ?2?V bias. The lower leakage currents of TiO2 with ammonium sulfide treatment arise from the improvement of interface quality. The dielectric constant and effective oxide charge number density are 33 and 2.5?1013?cm2, respectively. The lowest mid-gap interface state density is around 7.6?1011?cm?2?eV?1. The equivalent oxide thickness is 0.52?nm. The breakdown electric field increases with decreasing thickness in the range of 2.5 to 7.6?nm and reaches 9.3?MV/cm at 2.5?n...

Energy Technology Data Exchange (ETDEWEB)

This paper deals with the energy required to separate ethanol from an aqueous solution in a distillation column containing a solid phase. The solid phases evaluated consisted of either an amylatious (ground corn) or a cellulose (sugar cane bagasse) absorber whit particle sizes smaller than 4 mm. The water-retention capacity of each solid phase was measured by passing vapors or ethanol-water mixtures through the solid phase. When starting with initial concentrations bellow the azeotropic point, ethanol concentrations up to 99,5% (on corn) and 97,2% (on sugar cane) were achieved. The water content was evaluated potentiometrically (Karl`Fischer). Regarding the 2-4 mm ground corn solid phase column, the energy consumed was estimated to be reduced by 15,6% and 60% (by weight) ethanol-water mixture respectively. (author) 11 refs., 2 figs., 2 tabs

Energy Technology Data Exchange (ETDEWEB)

Continuous-wave (cw) operation at temperatures up to 23 /sup 0/C of an Al/sub 0.26/Ga/sub 0.26/In/sub 0.48/P/Ga/sub 0.52/In/sub 0.48/P/ Al/sub 0.26/Ga/sub 0.26/In/sub 0.48/P double heterostructure (DH) laser has been achieved for the first time. The threshold current was 160 mA at 20 /sup 0/C for a device with a 10-..mu..m-wide and 250-..mu..m-long ion-implanted stripe geometry. The emission wavelength was 671 nm during cw operation at 10 /sup 0/C. To reduce thermal resistance to a heat sink, a dually stacked structure made of a thin (approx.0.3 ..mu..m) p-AlGaInP layer and a p-Al/sub 0.76/Ga/sub 0.24/As layer was used as a cladding layer. The DH wafer was grown by atmospheric pressure metalorganic chemical vapor deposition.

Science.gov (United States)

We report on recent progress and improvements in the metal-organic chemical vapor deposition (MOCVD) growth of mid-infrared lasers and using a high speed rotating disk reactor (RDR). The devices contain AlAsSb active regions. These lasers have multi-stage, type I InAsSb/InAsP quantum well active regions. A semi-metal GaAsSb/InAs layer acts as an internal electron source for the multi-stage injection lasers and AlAsSb is an electron confinement layer. These structures are the first MOCVD multi-stage devices. Growth in an RDR was necessary to avoid the previously observed Al memory effects found in conventional horizontal reactors. A single stage, optically pumped laser yielded improved power (greater than 650 mW/facet) at 80K and 3.8um. A multi-stage 3.8-3.9um laser structure operated up to T=170K. At 80K, peak power greater than 100mW and a high slope- efficiency were observed in gain guided lasers.

Energy Technology Data Exchange (ETDEWEB)

Water injection into a vapor-dominated geothermal reservoir is an effective method of sustaining steam production from the field. Injection puts additional water to the reservoir and raises the prevailing reservoir pressure. This process improves the field`s productivity. However, the increased pressure also increases the water retention capacity of the reservoir rocks through the effects of adsorption and capillary condensation. Due to the significant costs associated with water injection programs, optimizing injection not only involves maximizing the energy yield from the resource but also the present worth of the project. Two crucial parameters that need to be established are: (1) how much to inject; and, (2) when to inject it. This study investigated the optimal design of these parameters. It was found that comparable energy yield can be attained for injection programs that are initiated at various stages of the field`s development. Higher injection rates are ...

Energy Technology Data Exchange (ETDEWEB)

In order to predict the effect of a fuel-coolant interaction after a hypothetical core-melt-down accident, a phenomenological model has been developed to describe the thermal and hydrodynamic behavior of a high-temperature molten jet when it interacts with saturated or subcooled water in a film boiling regime. The mechanisms of jet-material erosion were analyzed by Kelvin-Helmholtz instabilities on the coherent column and by boundary layer stripping on the leading edge. The heat transfer coefficient, vapor-film thickness, and net steam generation, all of which strongly affect the jet-breakup behavior, were solved analytically. It was found that the jet breakup (or erosion) depends strongly on the steam generation from the jet/water interaction. The jet-breakup length (i.e., penetration distance) was found to be sensitive to the initial jet temperature, water subcooling, and the physical state of the ambient water. The jet-breakup length and leading-edge velocity of ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents an analysis of the applicability of alternative systems for electric vehicle (EV) heating and air conditioning (HVAC). The paper consists of two parts. The first part is a cooling and heating load calculation for electric vehicles. The second part is an evaluation of several systems that can provide the desired cooling and heating in EVs. These systems are ranked according to their overall weight The overall weight is calculated by adding the system weight and the weight of the battery necessary to provide energy for system operation. The system with the minimum overall weight is considered to be the best, because minimum vehicle weight decreases the energy required for propulsion, and therefore increases the vehicle range. Three systems are considered as the best choices for EV HVAC. These are, vapor compression, ice storage and adsorption systems. These systems are evaluated, including calculations of system weight, system volume, and COP. The ...