International Nuclear Information System (INIS)

The description is presented of binary phase diagrams of titanium alloyed with the following elements: silver, aluminium, arsenic, gold, boron, barium, beryllium, bismuth, carbon, calcium, cadmium, cobalt, chromium, copper, iron, gallium, germanium, hydrogen, hafnium, indium, iridium, potassium, lithium, magnesium, manganese, molybdenum, nitrogen, sodium, niobium, nickel, oxygen, osmium, phosphorus, lead, palladium, platinum, plutonium, rhenium, lanthanium, cerium, preseodymium, neodymium, gadolinium, erbium, terbium, thulium, lutetium, rhodium, ruthenium, scandium, silicon, tin, strontium, tantalum, technetium, thorium, uranium, vanadium, tungsten, yttrium, ytterbium, zinc and zirconium.

International Nuclear Information System (INIS)

Samples of air-dust-concentration- and air-dust-deposit measurements were digested by a standardized wet digestion procedure and the amounts of substances in the dust according to class I TA Luft by Atomic Emission Spectroscopy with Inductively Coupled Plasma (AES-ICP). The characteristic values for procedures according to VDI 2449, sheet 1, were determined for lead, vanadium, cadmium, chromium, copper, nickel and zinc. By partial automatic control of the digestion procedure the personel expenditure of work could be reduced by a factor 13. Dust filter samples were analysed without sample preparation by evaporating the material with a solid state laser. The absolute detection limit was between 1 and 100 ng/cm"2 for the elements arsenic, cadmium, cobalt, chromium, mercury, antimony, selen and thallium. For sampling by means of the Beta-Staubmeter the relative detection limits for the laser-ICP were 10-fold lower than by use ...

International Nuclear Information System (INIS)

A method is described for determination of aluminium, cadmium, cobalt, chromium, copper, calcium, magnesium, sodium, potassium, manganese, nickel, lead, strontium, zinc, titanium and vanadium in iron ore. After dissolution, a 1 gram sample of iron ore is applied to a column of AGI-X8 anion exchange resin (chloride form), in 100 ml of 7M HCl. Aluminium, chromium, calcium, magnesium, sodium, potassium, manganese, nickel, lead, strontium, titanium and vanadium are eluted with 7M HCl; iron, copper and cobalt are eluted with 0.5M HCl; cadmium and zinc are eluted with 2M HNO_3. Iron is subsequently removed from copper and cobalt by a solvent extraction with methyl isobutyl ketone. The elements are determined in the eluates by atomic absorption spectrometry, except for titanium and vanadium, which are determined spectrophotometrically.

Energy Technology Data Exchange (ETDEWEB)

The invention is associated with organic geochemistry and may be used in conducting geological exploration operations for oil and gas. The purpose of the invention is to increase the precision of the method for determining the genesis of bitumoids. This is achieved through determining the isotopic composition of nickel or vanadium and from the anomalously high values of the isotopic ratio of Ni-58 to Ni-62 or from the anomalously low values of the isotopic ratio of vanadium, a conclusion is drawn about the epigenetic nature of the bitumoids. The proposed method is characterized by greater resolution due to the fact that the values of the isotopic ratios for oil bearing and water bearing structures are essentially not superimposed. The proposed method exceeds the resolution of metal metering studies in conducting geological exploration for oil and gas by 2 to 3 times.

Energy Technology Data Exchange (ETDEWEB)

A heat resistant nickel base alloy which is excellent in not only hot and cold workability but also high temperature strength properties and which also possesses satisfactory oxidation resistance. The nickel base alloy consists essentially of 0.001-0.15 percent carbon, 0.0005-0.05 percent calcium, 20.0-126.0 percent chromium, 4.7-9.4 percent cobalt, 5.0-16.0 percent molybdenum, 0.5-4.0 percent tungsten, with the total of molybdenum plus tungsten being from 9.0 to 16.5 percent, and the balance nickel and inevitable impurities. The alloy may further contain one selected from the group consisting of (1) 0.3-1.5 percent aluminum and 0.1-1.0 percent titanium, (2) 0.001-0.30 percent at least one of yttrium and rare earth elements, and (3) 0.001-1.0 percent at least one of niobium, vanadium and tantalum, whereby the aforementioned characteristics are further enhanced.

UK PubMed Central (United Kingdom)

Environmental arsenic is a world-wide health issue, making it imperative for us to understand mechanisms of metalloid uptake and detoxification. The predominant intracellular form is the highly mephitic...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Contents: recent trend of battery technologies; alkaline manganese battery with no mercury addition; high capacity zinc-air battery series for hearing aids; characteristics of vanadium-niobium-lithium rechargeable battery; high-energy density lithium-ion rechargeable battery; lithium polymer rechargeable battery: polymer gel electrolyte and electrode; high-capacity ni-cd battery sm120; high-capacity nickel-metal hydride battery; sealed-type batteries for electric vehicles; high-temperature-durable calcium-type battery for automobiles; sealed lead acid batteries for upss; solar cell power unit; solid oxide fuel cell (1); battery management system.

UK PubMed Central (United Kingdom)

This report examines the mortality experience of 527 men who retired from a copper smelter where they were exposed to airborne arsenic trioxide. Urinary arsenic values of all plant employees were determined...Full Text Available

UK PubMed Central (United Kingdom)

Chronic arsenic exposure has been suggested to contribute to diabetes development. We performed a systematic review of the experimental and epidemiologic evidence on the association of arsenic and type...Full Text Available

International Nuclear Information System (INIS)

Arsenic was predominantly present as inorganic arsenite in the fronds of the hyperaccumulator Chinese brake. - Arsenic speciation is important not only for understanding the mechanisms of arsenic accumulation and detoxification by hyperaccumulators, but also for designing disposal options of arsenic-rich biomass. The primary objective of this research was to understand the speciation and leachability of arsenic in the fronds of Chinese brake (Pteris vittata L.), an arsenic hyperaccumulator, with an emphasis on the implications for arsenic-rich biomass disposal. Chinese brake was grown for 18 weeks in a soil spiked with 50 mg As kg"-"1 as arsenate (AsO_4"3"-), arsenite (AsO_3"3"-), dimethylarsinic acid (DMA), or methylarsonic acid (MMA). Plant samples were extracted with methanol/water (1:1) and arsenic speciation was ...

International Nuclear Information System (INIS)

Uranium-aluminum alloys with a significant enrichment of uranium with "2"3"3U or "2"3"5U serve as nuclear fuels in research reactors. The quality assurance of this fuel requires, among other things, precise knowledge that all trace metal constituents that affect neutron economy, fuel integrity, and fuel fabrication process parameters are well within the specification limits. Trace metal characterization of "2"3"5U-Al alloy has been carried out by atomic spectrometry. The trace metal constituents of interest are grouped into common metals (silver, boron, calcium, cadmium, cobalt, chromium, copper, iron, magnesium, manganese, molybdenum, sodium, nickel, lead, silicon, tin, titanium, vanadium, tungsten, and zinc) and lanthanides (cerium, dysprosium, europium, gadolinium, holminium, lutetium, samarium, and terbium). The elements yttrium and zirconium are grouped with the latter in view of the chemical separation procedure used. The alloy samples ...

Science.gov (United States)

In the course of observing by means of Auger spectroscopy graphite gasification reactions catalyzed by metals, it has been found that in the presence of hydrogen, nickel appears to diffuse from the surface into the bulk of the graphite. When potassium is deposited on graphite, it is volatilized above 400/sup 0/C. Surprisingly the production of methane and carbon dioxide from the reaction of graphite and steam was catalyzed by potassium at as low a temperature as 250/sup 0/C. It has been shown that literature on the alkylation of benzene with synthesis gas is erroneous and that the products reported are due to Lewis acid catalyzed cracking of benzene. A novel cobalt mediated, reversible cleavage of a vinyl-hydrogen bond has been discovered. All products from the thermal decomposition of tetralin have been identified. The stereochemistry of cis-1, 2 dihydrotetralin was determined. In the utilization of the water gas shift reaction as a reducing agent for model coal ...

Energy Technology Data Exchange (ETDEWEB)

The ash of biomass fuels was analysed in order to identify its inorganic chemical characteristics. The experiments were carried out using different methods of extraction. The accuracy of the measurements was verified by comparative analyses using certified samples. The composition was shown to vary with the fuel type and ash fraction. In the case of arsenic and the toxic heavy metals cadmium, mercury and lead, accumulation factors of 1.4 to 43 were measured in the tissue filter ash. [German] Fuer die Bestimmung der stofflichen Eigenschaften von Biobrennstoffaschen werden neben der fuer die Ermittlung von Stoffbilanzen notwendigen Analyse der Gesamtgehalte, in Abhaengigkeit von der Zielsetzung und den gesetzlichen Vorgaben, unterschiedliche Extraktionsverfahren eingesetzt. Fuer die Gesamtgehaltsbestimmung wurden aus laborinternen Wiederholungsuntersuchungen sowie einem laborexternen Analysenvergleich Kenngroessen fuer die Praezision und Richtigkeit abgeleitet. ...

Science.gov (United States)

Not Available

Science.gov (United States)

In view of the effect of the acidity on the oxidation potentials of nitrous, arsenous, and arsenic acids, one should expect a complex relationship between the rate of arsenic (III) to arsenic (V) and the pH of the solution. They studied the kinetics of the reaction 2AsO/sub 2//sup -/ + O/sub 2/ ..-->.. 2AsO/sub 3//sup -/ as functions of concentrations (partial pressure) of all the components of the system NaAsO/sub 2/-HCl(HClO/sub 4/)-NaNO/sub 2/-KI-H/sub 2/O-O/sub 2/ and temperature. The study of the kinetics of arsenic(III) oxidation to arsenic(V) with oxygen in the presence of sodium nitrite and iodide ions showed that the reaction rate passes through a maximum at an acid content of 1.2-2.5 M and rises in proportion to the second exponent of the sodium nitrite concentration and to the first exponent of the iodide ion concentrations and partial oxygen pressure. A fall in the ...

Energy Technology Data Exchange (ETDEWEB)

Due to the consumption of chicken and chicken products in Turkey at high ratio, trace metal content of chicken and chicken products from Turkey were determined by atomic absorption spectrometry after microwave digestion. The accuracy of the method was confirmed by analysis of standard reference material (NIST SRM 1577b Bovine liver). Trace element content in various parts of chicken samples and chicken products were to be in the range of 0.10-114 {mu}g/g for copper, 0.25-6.09 {mu}g/kg for cadmium, 0.01-0.40 {mu}g/g for lead, 0.10-0.91 {mu}g/g for selenium, 0.05-3.91 {mu}g/g for manganese, 0.06-0.10 {mu}g/g for arsenic, 0.01-0.72 {mu}g/g for chromium, 0.01-2.08 {mu}g/g for nickel, 0.01-0.02 {mu}g/g for cobalt, 0.10-1.90 {mu}g/g for aluminium, 1.21-24.3 {mu}g/g for zinc, 2.91-155 {mu}g/g for iron. The levels of lead in some analyzed chicken products were higher than the recommended legal limits for human consumption.

Energy Technology Data Exchange (ETDEWEB)

Cathodic arc deposition is an established and industrially applied technique for the formation of nitrides (e.g. TiN); it can also be used for metal oxide thin film formation. A cathodic arc plasma source with the desired cathode material is operated in an oxygen atmosphere of appropriate pressure, and metal oxides of various stoichiometric composition can be formed on different substrates. We report here on a series of experiments on metal oxide formation by cathodic arc deposition for different applications. Black copper oxide has been deposited on accelerator components to increase the radiative heat transfer between the parts. Various metal oxides such as tungsten oxide, niobium oxide, nickel oxide and vanadium oxide have been deposited on ITO glass to form electrochromic films for window applications. Optical waveguide structures can be formed by refractive index variation using oxide multilayers. We have synthesized multilayers of Al{sub ...

Energy Technology Data Exchange (ETDEWEB)

Density functional theory (DFT) calculations using plane-wave methods were performed for Li2TMPO4F, LiTMPO4F, and TMPO4F (TM=V, Mn, Fe, Co, Ni) to address their feasibility as high-voltage cathode materials for Li ion batteries. We computed their structures, average open circuit voltages, and thermal stabilities for step-wise lithiation/delithation (discharge/charge) reactions. The calculations suggest that associated unit cell volume changes are sufficiently small on average that they should not be a significant detriment to the mechanical stability of the cathode. In the nickel case, the calculated volume change deviates from the series by increasing during the first delithiation step. Furthermore, the volume increases for all these materials during the second delithiation step. It appears that the relative volume expansion in the series during delithiation is directly correlated to the degree of d-p rehybridization. Predicted average open circuit voltages ...

Energy Technology Data Exchange (ETDEWEB)

Careful sample preparation and secondary ion mass spectroscopy have been used to characterize arsenic dose loss to the silicon-oxide interface. Using high resolution x-ray photoelectron spectroscopy for microprofiling, we have directly observed the pileup of arsenic at the silicon dioxide-silicon interface. At least half of the pileup is shown to be on the silicon side of the interface in the first monolayer of silicon. Monolayer chemical oxidation and etching are successfully used to profile this pileup in silicon. This pileup contains most of the arsenic dose loss that occurs during transient enhanced diffusion. This result is crucial to correctly model the dose loss and provides physical justification for using a trap/detrap model at the interface, which is necessary to account for the fact that the arsenic surface concentration remains constant during an anneal and the fact that the dose loss is ...

Science.gov (United States)

Environmental arsenic is a world-wide health issue, making it imperative for us to understand mechanisms of metalloid uptake and detoxification. The predominant intracellular form is the highly mephitic arsenite, which is detoxified by removal from cytosol. What prevents arsenite toxicity as it diffuses through cytosol to efflux systems? Although intracellular copper is regulated by metallochaperones, no chaperones involved in conferring resistance to other metals have been identified. In this article, we report identification of an arsenic chaperone, ArsD, encoded by the arsRDABC operon of Escherichia coli. ArsD transfers trivalent metalloids to ArsA, the catalytic subunit of an As(III)/Sb(III) efflux pump. Interaction with ArsD increases the affinity of ArsA for arsenite, thus increasing its ATPase activity at lower concentrations of arsenite and enhancing the rate of arsenite extrusion. Cells are consequently resistant to environmental ...

UK PubMed Central (United Kingdom)

Arsenic trioxide (As₂O₃), used to treat promyelocytic leukemia, triggers cell death via unknown mechanisms. To further our understanding of As₂O₃-induced...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

We present experimental evidence for self-organization of nickel microparticles in silicon under certain thermodynamic conditions of nickel diffusion doping. The concentration and distribution of the microparticles in silicon are very uniform. Additional anneals lead to self-ordering of the impurity microparticles.

UK PubMed Central (United Kingdom)

A simplification of Sandell's method for estimating nickel in urine is described. Nickel is a normal constituent of most articles of food and between 0·01 and 0·03 p.p.m. are found in...Full Text Available

International Nuclear Information System (INIS)

A study is made of the mechanical properties of vanadium irradiated with fast neutrons up to dose 8.6.10"-"4 dpa, as a function of the temperature of post-radiation annealing. The radiation-annealing hardening (RAH) effect is observed at 300"oC, in agreement with previous studies. It is established for the first time that RAH is accompanied by fall in ductility. A phenomenological model is described which explains the dependence of RAH on radiation dose and temperature, as well as on the content of chemically active alloying impurities. (author).

British Library Electronic Table of Contents (United Kingdom)

Iron, zinc, copper and manganese are essential metals for cellular enzyme functions while cadmium, mercury and the metalloid arsenic lack any biological function. Both, essential metals, at high concentrations, and non-essential metals and metalloids are extremely reactive and toxic. Therefore, plants have acquired specialized mechanisms to sense, transport and maintain essential metals within physiological concentrations and to detoxify non-essential metals and metalloids. This review focuses on the recent identification of transporters that sequester cadmium and arsenic in vacuoles and the mechanisms mediating the partitioning of these metal(loid)s between roots and shoots. We further discuss recent models of phloem-mediated long-distance transport, seed accumulation of Cd and As and rec...

Energy Technology Data Exchange (ETDEWEB)

National soil quality criteria for the protection of ecological receptors, including livestock and wildlife, are currently under development in Canada. Based on an evaluation of direct soil contact and soil and food ingestion pathways for sensitive species, soil quality criteria for lead, copper, arsenic, cadmium and mercury for three land use categories have been derived. The draft values, in mg/kg soil, for agricultural, residential/parkland, commercial/industrial land uses are: mercury, 4, 4, 30; copper, 62, 62, 100; cadmium, 10, 10, 27; lead, 70, 250, 400; arsenic, 17, 17, 26. Critical data requirements in developing soil quality criteria are also reviewed.

International Nuclear Information System (INIS)

... FUEL CYCLE AND FUEL MATERIALS MATERIALS SCIENCE chromium-nickel

UK PubMed Central (United Kingdom)

We have developed a method to extract and separate phytochelatins (PCs)—metal(loid) complexes using parallel metal(loid)-specific (inductively coupled plasma-mass spectrometry) and organic-specific...Full Text Available

International Nuclear Information System (INIS)

Tungsten (W) coating on fusion candidate V-4Cr-4Ti (NIFS-HEAT-2) substrate was demonstrated with plasma spray process for the purpose of applying to protection of the plasma facing surface of a fusion blanket. Increase in plasma input power and temperature of the substrate was effective to reduce porosity of the coating, but resulted in hardening of the substrate and degradation of impact property at 77 K. The hardening seemed to be due to contamination with gaseous impurities and deformation by thermal stress during the coating process. Since all the samples showed good ductility at room temperature, further heating seems to be acceptable for the vanadium substrate. The fracture stress of the W coating was estimated from bending tests as at least 313 MPa, which well exceeds the design stress for the vanadium structure in fusion blanket. (author)

International Nuclear Information System (INIS)

A study was made on interaction of vanadium (4) ions with dyes-pyrogallol red, brompyrogallol red and gallein- in the range of pH = 0-6. The maximal light absorption for gallein and brompyrogallol red is observed at pH=4 and #lambda#max = 545 nm and 560 nm respectively. The compound of vanadium (4) with pyrogalloe red is characterized by the maximal light absorption at pH=5 and #lambda#max=560 nm. Component ratio in all analyzed compounds is equal to 1:2. Molar extinction coefficients for compounds with gallein, pyrogallol red and brompyrogallol red are equal to 5000, 550 and 7400, and logarithms of stability constants - to 9.27, 13.17 and 13.25 respectively.

International Nuclear Information System (INIS)

The observation by inelastic neutron scattering techniques of a high energy peak in the phonon spectrum (14 THz) of V_3Si is reported, and is attributed to a peak in the phonon density of states due to vanadium motions by the incoherent inelastic neutron scattering process.

Energy Technology Data Exchange (ETDEWEB)

The authors investigate the possibility of the direct heterogeneous catalytic synthesis of ethylbenzoate from benzonitrile. The catalysts tested were oxides of aluminium, titanium, and vanadium. The main conversion product detected chromatographically was ethylbenzoate; benzaldehyde, benzamide, and benzanilide were also identified. Aluminium oxide was found to be the most effective catalyst.

International Nuclear Information System (INIS)

Growing competitiveness of alternative manufacturing routes requires cost minimization in the production of drop forged components. The authors analyse the potential of medium carbon, vanadium microalloyed steels for drop forging. Laboratory and industrial experiments have been carried out emphasizing deformation and temperature cycles, strain rates and dwell times showing a typical processing path, associated mechanical properties and corresponding microstructures. The steels the required levels of mechanical properties on cooling after forging, eliminating subsequent heat treatment. The machinability of V-microalloyed steels is also improved when compared with plain medium carbon steels. (author)

Energy Technology Data Exchange (ETDEWEB)

It is reported about the adsorptive stripping voltammetric determination of uranium, antimony, tin, vanadium and molybdenum using chloranilic acid as complex forming reagent. The determination limits are in the l{sup 1}-range. (orig.) [Deutsch] Es wird ueber die Bestimmung von Uran, Antimon, Zinn, Vanadium und Molybdaen durch Adsorptions-Stripping-Voltammetrie mit Chloranilsaeure als Komplexbildner berichtet. Die Bestimmungsgrenzen liegen im ng l{sup -1} Bereich. (orig.)

CERN Document Server

beta- and gamma-decay studies of neutron-rich chromium, manganese, cobalt and nickel isotopes including the new isotopes $^{60}$Cr and $^{60g}$Mn

UK PubMed Central (United Kingdom)

IntroductionWhile epidemiological methods have grown in sophistication during the 20^th century, their application in historical occupational (and environmental) health...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The inhibiting effects of two mineral compounds on corrosion of nickel in phosphoric acid (H[sub 3]PO[sub 4]) polluted by sulfide ions (S[sup 2[minus

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The use of nickel alloys in Flue Gas Desulfurization (FGD) applications is described. Recently, nickel alloys 625 and C-276 have been clad to carbon steel plate. Production and properties of the clad plate are reviewed and a brief discussion is presented on production, fabrication and welding. Laboratory and field corrosion tests in SO/sub 2/ scrubber environments suggest that alloy 625 and C-276 clad steel plates are as corrosion resistant as the solid alloy plate.

International Nuclear Information System (INIS)

A study of specific adsorption of arsenic (As) and humic acid (HM) onto Pt and PtO films using cyclic voltammetry and cyclic massogram in 0.5-M H_2SO_4 is presented, which may serve as an alternative to studies involving specific adsorption of these species on soil minerals. Adsorption of As is normally evaluated by conducting batch adsorption experiments, followed by analysis using hydride-generation atomic absorption spectrophotometry (HGAA) or inductively coupled plasma-optical emission spectrometry (ICP-OES). We found that specific adsorption of As and HM depends both on the surface and on these species present in the adsorption solution. HM does not desorb previously adsorbed As at the HM concentrations used in the present study, but it does co-adsorb with As from a 1 x 10"-"6-M aqueous solution of As_2O_3 containing 1 mg of carbon L"-"1 HM. Arsenic adsorbs strongly on Pt in the presence of HM or during sequential specific adsorption with ...

British Library Electronic Table of Contents (United Kingdom)

In this paper we demonstrate the electrodeposition of nickel, a common ferromagnetic material, in various magnetically desirable shapes including nanowires, nanoparticles and highly faceted shells. In order to obtain three dimensional mesostructures, the electrochemical deposition of nickel was performed on highly oriented pyrolytic graphite (HOPG) under different electrolyte composition and deposition potential conditions. Under potentiostatic deposition at one distinct potential negative with respect to the reversible potential of nickel, three stages of nucleation and growth take place leading to a complex morphology of deposits. However, dual-pulse potential deposition and electrodeposition in low pH solutions causing hydrogen evolution, lead to nickel deposits in the form of nanowires...

British Library Electronic Table of Contents (United Kingdom)

Monthly sampling of slightly alkaline arsenic-rich stream in the Mokrsko gold deposit revealed seasonal variations in dissolved Zn, Cu, As and Mo. Concentrations of trace metal cations (Zn, Cu) increased as much as 330 and 178%, respectively, from minimum mean values at autumn to maximum mean values at spring. In contrast, concentrations of trace element oxyanions (As, Mo) revealed opposite seasonal pattern with increase to 189% (As) and 123% (Mo) during summer?autumn, indicating that in-stream biogeochemical process(es) played the main role in controlling the seasonal variations of these trace elements. The trace elements were mainly scavenged by low crystalline Mn oxyhydroxide and Fe oxyhydroxide (ferrihydrite). Results are consistent with sorption and coprecipitation processes controlli...

International Nuclear Information System (INIS)

We present results of multiple-time-scale simulations of 5, 10 and 15 keV low temperature ion implantation of arsenic on silicon (100), followed by high temperature anneals. The simulations start with a molecular dynamics (MD) calculation of the primary state of damage after 10ps. The results are then coupled to a kinetic Monte Carlo (MC) simulation of bulk defect diffusion and clustering. Dose accumulation is achieved considering that at low temperatures the damage produced in the lattice is stable. After the desired dose is accumulated, the system is annealed at 800 degrees C for several seconds. The results provide information on the evolution for the damage microstructure over macroscopic length and time scales and affords direct comparison to experimental results. We discuss the database of inputs to the MC model and how it affects the diffusion process.

International Nuclear Information System (INIS)

Vanadium(V) in aqueous HCl, HNO_3 or H_2SO_4 solutions is extracted with 2-carbethoxy-5-hydroxy-1-(4-tolyl)-4-pyridone (HA) dissolved in CHCl_3 and determined spectrophotometrically, Depending on the composition of the aqueous phase, two complexes are formed. At pH 1 (HCl, HNO_3, H_2SO_4) VO_2A(HA)_2 is formed with maximal absorption at 478 nm. However, from 4-5 M HCl, VO_2Cl(HA)_3 is extracted, and has maximal absorption at 615 nm. The same complex is extracted from 2-3 M HNO_3 or 3-4 M H_2SO_4 if enough chloride is added. Solutions of both complexes follow Beer's law and the molar extinction coefficients are 4.15x10"3 1.mole"-"1cm"-"1 at 478 nm and 5.10x10"3 at 615 nm. The determination of vanadium at both wavelengths is very simple, fast and selective. The composition of the complexes was established by the usual methods as well as by characterization of the isolated crystalline compounds by elemental analysis and infrared spectroscopy. ...

Energy Technology Data Exchange (ETDEWEB)

Alumina (94 and 99.8% grade compositions) was brazed directly to itself with gold-based active brazing alloys (ABA's) containing vanadium additions of 1,2 and 3 weight percent. The effects of brazing conditions on the joint properties were investigated. Wetting behavior, interfacial reactions, microstructure, hermeticity and tensile strength were determined. Wetting was fair to good for the ABA and base material combinations. Microanalysis identified a discontinuous Al-V-O spinel reaction product at the alumina-braze interface. Tensile strength results for 94% alumina were uniformly good and generally not sensitive to the vanadium concentration, with tensile values of 85-105 MPa. There was more variability in the 99.8% alumina strength results, with values ranging from 25-95 MPa. The highest vanadium concentration (3 wt. %) yielded the highest joint strength for the brazed 99.8% alumina. Failures in the 99.8% ...

Wastenet

...Disinfection Byproducts, Mercury, Lead, Copper, Arsenic ,Pathogens,Radionuclides,Drinking Water Contaminants,Microbial Pathogens,Fertilizer, Water Topics | Laws and Regulations | US EPA Jump to main content A-Z Index Advanced Search What are you looking for? Learn the Issues Science & Technology Laws &...

Science.gov (United States)

Arsenic in soils from the Asarco Lead Smelter in East Helena, Montana was characterized by X-ray absorption spectroscopy (XAS). As oxidation state and geochemical speciation were analyzed as a function of depth (two sampling sites) and surface distribution. These results were c...

Energy Technology Data Exchange (ETDEWEB)

After a presentation of methods and tools for the basic and extensive characterization of polluted sites and the study of evolution and transfer of current organic pollutants in the ground, the example of the rehabilitation of an old Rhone-Poulenc site (at Chauny, France) polluted with metals and arsenic, is described: soil and aquifer diagnosis, risk analysis and determination of migration schemes

International Nuclear Information System (INIS)

The effect of W and V on the high temperature strength properties of 12%Cr-15%Mn austenitic steels was studied from the view point of precipitation hardening and internal stress. The contribution of W addition to the tensile and creep-rupture strength was not so large. By contrast the combined addition of W and V increased the strength considerably. These are resulted from the precipitation of fine vanadium nitride (VN) within grains and the enhancement of M_2_3C_6 type carbide precipitation at grain boundaries. The V added material had large internal stress value which is considered to be due to dislocation movement disturbed by fine vanadium nitrides. (author).

Energy Technology Data Exchange (ETDEWEB)

For a wider application of GaAs single crystals for semiconductor devices a cheaper process to grow crystals with high purity and low dislocation density is required. According to todays knowledge the Czochralski method with a hot wall vessel should be the choice. The temperature of the vessel has to be 700deg C to avoid condensation of arsenic which vapourizes from the 1240deg C hot melt. Arsenic vapour is very agressive against all metals. Therefore the corrosion resistance of metals and alloys with a high melting point and also ceramics has been tested. All the alloys under investigation are corroded severely so that they have to be excluded as a material for the vessel. The metals tantalum, molybdenum and tungsten are more resistent, titanium forms initially a thick protection layer and further corrosion is greatly reduced. The ceramics investigated (TiB{sub 2}; ALN; Makor; BN) are not attacked by arsenic though they ...

British Library Electronic Table of Contents (United Kingdom)

The adsorption and corrosion inhibition behavior of three selected thiosemicarbazone derivatives, namely 3-pyridinecarboxaldehyde thiosemicarbazone (META), isonicotinaldehyde thiosemicarbazone (PARA) and 2-pyridinecarboxaldehyde thiosemicarbazone (ORTHO) at the nickel surface were studied electrochemically by Tafel and impedance methods and computationally by carrying out Monte Carlo searches of configurational space on nickel/thiosemicarbazone derivative system. Electrochemical measurements showed that the inhibition efficiency of these compounds increased with increase in their concentration. The recorded inhibition efficiencies of the three tested thiosemicarbazone increase in the order: META>PARA>ORTHO. Polarization studies showed that these compounds act as mixed-type inhibitors for n...

International Nuclear Information System (INIS)

A reaction of aqueous-methanol solutions of thiocarbazide and salycilic aldehyde, taken in a molal ratio of 1:2 on the matrix of oxovanadium(VO) in the presence of aqueous ammonium results in a coordination compound of the VC_1_5H_1_2N_4O_3S composition. Similar compounds are obtained with salts of nickel(2) and copper(2). Complexes of oxovanadium(4) and copper(2) have effective magnetic moments normal for systems with a spin of 1/2. The compound with nickel is diamagnetic. These data agree with the configuration of the coordination compounds obtained.

International Nuclear Information System (INIS)

Repassivation resulting from the bared metal surface is a critical process for judging whether or not material suffers from corroding or immunizing. Nickel based alloys with high chromium content were developed to increase the corrosion resistant to sulphur compounds. Active humps resulting from active dissolution of nickel were obtained by creating the bared metal surfaces in thiosulphate solutions. The lower the Cr content the higher is the dissolution rate. The passive films formed on the bared metal surface were examined by ac impedance. Results suggest the formation of multi-layers oxide which were affected by active dissolution reactions during repassivation. (author).

British Library Electronic Table of Contents (United Kingdom)

An hydrazone derivative, 1,2-cyclohexanedione bis-benzoyl-hydrazone (1,2-CHBBH), has been used as a selective reagent for an advanced environmental application consisting of separating the different species of nickel in natural waters by solvent extraction. The effects of pH and reagent concentration on the extraction process were studied, as well as the influence of both organic (humic acids) and inorganic ligands (Cl-). Under natural conditions, organic and inorganic nickel species presented different extraction behaviors, and the variations in extraction yields could be correlated with the concentrations of organic complexes in the samples, allowing the separation of labile and non-labile nickel species in both fresh and marine waters.

Energy Technology Data Exchange (ETDEWEB)

In this letter, examples of microstructural instabilities that can significantly affect the low crystal fatigue (LCF) life are pointed out.

International Nuclear Information System (INIS)

Russian 1974. USSR Alekseev, VV Nemets, OF Stryuk, Yu.S. Tokarevskij,

International Science & Technology Center (ISTC)

Corrosion- and Wear Resistant Silicon Containing Chromium-Manganese and Nickel-Chromium-Manganese Nonmagnetic Steels with Increased Strength and Toughness for Reliable Work at Normal and Cryogenic Temperatures

Energy Technology Data Exchange (ETDEWEB)

Iron nickel chromium manganese silicon and iron chromium nickel manganese silicon molybdenum niobium alloys have a so-called duplex structure in a wide concentration range. This causes an excellent resistance to wear superior in the case of adhesive stress with optimized concentrations of manganese, silicon, molybdenum and niobium. The materials can be used for welded armouring structures wherever cobalt and boron-containing alloy systems are not permissible, e.g. in nuclear science. Within the framework of pre-investigations for manufacturing of filling wire electrodes, cast test pieces were set up with duplex structure, and their wear behavior was examined. (orig.).

International Nuclear Information System (INIS)

The alloy of Ti-Al-Mo-V-Cr system is studied for its structure in a strained state and specific features of #beta#-#alpha# transformation in a #beta#-matrix and deformation twins on ageing. It is determined that preliminary deformation initiates the decomposition of solid solution on aging. In a metastable #beta#-titanium alloy the substructure of deformation twins is shown to vary essentially with aluminium and chromium partial substitution for molybdenum and vanadium

British Library Electronic Table of Contents (United Kingdom)

A formula is obtained which describes the kinetics of low-temperature radiation hardening caused by creation of dislocation loops of interstitial type during irradiation. The radiation hardening of aluminum and vanadium is estimated using this formula and results of experiments on studying processes of nucleation and growth of interstitial dislocation loops in these materials by transparent electron microscopy. It is shown that the proposed formula is valid for description of the kinetics of low-temperature radiation hardening.

International Nuclear Information System (INIS)

In a cold fusion method by electrolysis, a hydrogen occluding material mainly comprising vanadium is used as a material for a negative electrode, and lithium isotopes are incorporated in the material by more than 93%. That is, the ratio of lithium 7 ("7Li) isotope is increased to higher than the natural existent ratio, so that tritium ("3H) concentration in the hydrogen occluding material can be increased, to attain energy at high efficiency. (T.M.).

UK PubMed Central (United Kingdom)

Short and long-term pulmonary response to inhaled nickel hydroxide nanoparticles (nano-Ni(OH)₂, CMD = 40 nm) in C57BL/6 mice was assessed using a whole body exposure system. For short-term...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Molecular dynamics computer simulations of a dense nanocrystalline Nickel sample are performed on the parallel Cray T3 (EPFL-Lausanne). The sample contains 50 grains with an average size of 3 nm. By perturbing the relaxed configuration elastic and plastic properties are studied. (author) 1 fig., 1 ref.

International Nuclear Information System (INIS)

Investigated are the characteristics of high-temperature plastic deformation the velocity sensitivity of flow stresses, deformation curves, flow stresses, deformation before rupture - as well as the structure of beryllium alloys containing nickel (0.5-4 %), yttrium (0.5-2 %) and aluminium (38 %). The alloys containing nickel (2%) and yttrium (0.5 %) are superplastic, however, deformation before fracture of the alloys is lower than that of the unalloyed beryllium. The singularities of high-temperature plastic flow of the alloys and the causes of deterioration of their plasticity are determined.

International Nuclear Information System (INIS)

Effect of hydroxide nature, concentration and temperature on corrosion resistance of domestic steels and alloys to hot NaOH, KOH, LiOH solutions is considered. It is ascertained that by corrosion growth in relation to stainless steels and nickel alloys, the hydroxides are placed in the following sequence: LiOHnickel alloy tendency to cracking is manifested, are determined. 12 refs., 12 figs.

Energy Technology Data Exchange (ETDEWEB)

To reconstruct the profiles of heavy metal levels in the South Ocean ecosystem of Antarctica, the concentrations of lead (Pb), copper (Cu), arsenic (As), cadmium (Cd), and zinc (Zn) in seal hairs and lake sediments spanning the past 1500 years from Fildes Peninsula of King George Island and in weathering lake sediments from Nelson Island of West Antarctica were determined. The lead contents in the seal hairs and the weathering sediments show a sharp increase since the late 1800s, very likely due to anthropogenic contamination from modern industries. After the 1980s, the Pb content in seal hairs dropped by one-third, apparently due to the reduced usage of leaded gasoline in the Southern Hemisphere. Copper arises mainly from the weathering process, and its level may be substantially affected by climatic conditions. The concentrations of Cd, As, and Zn do not show any clear temporal trends.

International Nuclear Information System (INIS)

The author's achievements in the title field are summarized and discussed. The following topics are dealt with: (i) principles of radionuclide X-ray fluorescence analysis; (ii) mathematical methods in X-ray fluorescence analysis; (iii) Ross differential filters; (iv) application of radionuclide X-ray fluorescence analysis in the coal industry (with emphasis on the determination of the ash content, sulfur content, and arsenic content of coal); and (v) evaluation of the X-ray fluorescence analyzer from the radiological safety point of view. (P.A.).

British Library Electronic Table of Contents (United Kingdom)

Abstract Introduction - It is estimated that about 70-80% of the world's population relies on non-conventional medicine, mainly of herbal origin. However, owing to the nature and sources of herbal medicines, they are sometimes contaminated with toxic heavy metals such as lead, arsenic, mercury and cadmium, which impose serious health risks to consumers. It is critical to analyse source materials for heavy metals in order to ensure that their concentrations meet the related standards or regulations limiting their concentrations in herbal medicines. In this review, different analytical methods for analysis of heavy metals in herbal medicines are discussed. Objective - To provide a comprehensive review of the current state of the art in analytical methods used to detect heavy metals in herbal...

International Nuclear Information System (INIS)

Chinese brake fern (Pteris vittata L.), an arsenic (As) hyperaccumulator, has shown the potential to remediate As-contaminated soils. This study investigated the effects of soil amendments on the leachability of As from soils and As uptake by Chinese brake fern. The ferns were grown for 12 weeks in a chromated-copper-arsenate (CCA) contaminated soil or in As spiked contaminated (ASC) soil. Soils were treated with phosphate rock, municipal solid waste, or biosolid compost. Phosphate amendments significantly enhanced plant As uptake from the two tested soils with frond As concentrations increasing up to 265% relative to the control. After 12 weeks, plants grown in phosphate-amended soil removed >8% of soil As. Replacement of As by P from the soil binding sites was responsible for the enhanced mobility of As and subsequent increased plant uptake. Compost additions facilitated As uptake from the CCA soil, but decreased As uptake from the ASC soil. Elevated As uptake ...

Energy Technology Data Exchange (ETDEWEB)

The direct addition of nickel powder to the reaction mixtures of 1,3-dialkyl-4,5-dioxoimidazolidine-2-thione (1) with the thionation Lawesson reagent produces [Ni{sup II}(R{sub 2}timdt{sup -}){sub 2}] (R{sub 2}timdt = 1,3-dialkylmidazolidine-2,4,5-trithione). These complexes belong to a new class of nickel-dithiolenes, showing remarkably high absorption ({epsilon} {approx} 80 000 dm{sup 3} mol{sup -1} cm{sup -1}, {lambda} {approx} 1000 nm) in the near-infrared region (near-IR), accompanied by high photochemical stability that makes these complexes promising near-IR dyes.

International Nuclear Information System (INIS)

In equipment industries, the equipments handling industrial water and pure water are numerous. In power generation including nuclear power generation, water serves as a working medium. Review is made on the experiences in the corrosion of iron and nickel base alloys in high temperature, high pressure water and the results of researches derived from them. Under high temperature and high pressure, carbon steel, low alloy steel, stainless steel and high nickel alloy cause corrosion even in pure water. But in the case of serious corrosion, chlorine, oxygen, alkali and others in water take part. The following matters are described: corrosion by steam; stress corrosion cracking in pure water; corrosion by impurities in high temperature, high pressure pure water, i.e. chlorine ions, dissolved oxygen, and alkali; corrosion under radiation. (J.P.N.).

International Nuclear Information System (INIS)

The authors investigate the corrosion and anodic behavior of steels 12Kh18N10T, 08Kh21N6M2T, and 06KhN28MDT, nickel, and molybdenum in 10-40% naturally aerated solutions of H_2TiF_6 at 20 and 50 degrees C. The authors found that in solutions of fluotitanic acid, as also in tetrafluoroboric and hydrofluoric acids, the most stable alloys are chromium-nickel-molybdenum alloy of type 06KhN28MDT and (for acid concentrations above 20%) copper-nickel-alloys of the monel metal type. Steels 12Kh18N10T and 08Kh21N6M2T can be used in acid concentrations of less than 10% and temperatures up to 20 degrees C with anodic protection.

International Nuclear Information System (INIS)

The chemical composition and the semiconducting properties of passive films formed on nickel based alloy (Alloy 600) in acidic sulphate solution, pH 2.0 at room temperature were studied using Auger analysis, voltammetric techniques and the Mott-Schottky approach. The results obtained revealed that the presence of both chromium and mixed nickel-iron oxides in the films leads to the development of a p-n heterojunction, which controls their electronic structure, similarly manner to the case of stainless steels and Alloy 600 in borate buffer solution. This behavior has been interpreted as representing of an oxide system, which has a duplex character, with an inner p-type semiconducting region, mainly formed by chromium oxide and an outer n-type semiconducting region, containing iron oxide. It could also be observed that the nickel oxide present in the films acts as a barrier layer conferring improved protection.

International Nuclear Information System (INIS)

The study of passive films formed on a nickel base alloy type Inconel 600 is performed by capacitance measurements (Mott-Schottky approach). This research is supported by the passivation study of the alloying elements Ni, Cr, Fe and high purity alloys Ni-Cr, Ni-Fe, Ni-Cr-Fe. The results obtained show that the capacitive behaviour of the Inconel 600 in the passive state is similar to that on a p-n heterojunction to which a barrier zone of nickel oxide is added. The individual or combined action of alloying elements on the development of this kind of electronic structure is discussed. (authors). 5 refs., 6 figs.

British Library Electronic Table of Contents (United Kingdom)

Reaction between [V^I^VO(acac)2] and the ONN donor Schiff base Hpydx-aepy (I) (Hpydx-aepy=Schiff base obtained by the condensation of pyridoxal and 2-aminoethylpyridine) resulted in the formation of a complex [V^I^VO(acac)(pydx-aepy)] (1). Addition of aqueous 30% H2O2 to 1 yields the poor stable oxidoperoxidovanadium(V) complex [V^VO(O2)(pydx-aepy)] (2). Its formation has also been demonstrated in solution by treating 1 with H2O2 in methanol. Reaction of vanadium exchanged zeolite-Y with I in methanol followed by aerial oxidation gave zeolite-Y encapsulated dioxidovanadium(V) complex, abbreviated as [V^VO2(pydx-aepy)]-Y (4). The crystal and molecular structure of 1 has been determined, confirming the ONN binding mode of the ligand. The encapsulated complex [V^VO2(pydx-aepy)]-Y (4) catalyse...

International Nuclear Information System (INIS)

At Tarapur Atomic Power Station 3 and 4, 540 MWe Pressurised Heavy Water Reactors, core being large in size requires a continuous in core monitoring for local flux disturbances. Nearly 200 Self Powered Neutron Detectors (SPNDs) of the Straight Individually Replaceable (SIR) type are distributed in the reactor core. For purpose of reactor regulation and protection, cobalt SPNDs that have a prompt response for changes in power is used for in-core flux mapping, vanadium SPNDs that provide accurate measure of neutron flux, even though having slow response is used In core SPNDs are placed in Vertical Flux Units (VFU) and Horizontal Flux Units (HFUs). These SPNDs were to be replaced at regular intervals to meet the design intent. Cobalt SPNDs have dose rates of the order of 1000 Gy/h and the Mineral Insulated (MI) cables of Vanadium SPNDs have dose rates of the order of 100 Gy/h. So far 3 Cobalt SPNDs were removed from HFUs and are being stored in ...

Energy Technology Data Exchange (ETDEWEB)

A 9Cr-1Mo steel with properties improved over other ferritics in the ranges from 9 to 12% Cr and 1 to 2% Mo and over the widely used 2 1/2 Cr-1Mo steel has recently been developed. The main changes in the modified alloy, compared with the standard alloy, include: addition of niobium and vanadium, to improve the alloy's elevated-temperature strength properties; a specified range for each element; and a specification for nitrogen, which is not listed for the standard 9Cr-1Mo. Microstructural work has indicated that the improved strength of the modified alloy comes from two factors: (1) fine M/sub 23/C/sub 6/ precipitate particles nucleate on Nb/C, N, which comes out first during the heat treatment; and (2) the vanadium enters M/sub 23/C/sub 6/ and retards its growth at the service temperature. Mechanical properties discussed were Charpy-impact, tensile, and creep properties. Other properties included were: thermal expansion coefficient, ...

CERN Document Server

The aim of this work was to study the possibility of producing a fast switching optical thin film device to react to laser radiation in the visible/near infrared region of the spectrum. The switching mechanism was to be thermally driven. A computer program was written to enable the effects of changes of the refractive index of a component of a multilayer thin film stack to be modelled. Attempts to use the phase transition in vanadium dioxide were unsuccessful because, in the spectral region of interest, the 'open-state' absorption was too great. A class of materials known as 'the bronzes' was identified as being potentially useful. Attempts were made to produce thin films of bronze compounds of vanadium, tungsten and molybdenum by the techniques of conventional thermal evaporation and laser ablation for further studies. The former technique appeared to suffer from problems of decomposition of the source material. The latter technique showed ...

International Nuclear Information System (INIS)

The penetration depth and concentration distribution for vanadium ions with low energy implanted into the dry peanut seeds is determined by scanning electron microscope and X-ray energy dispersion spectrometer. The results show that the depth-concentration distribution is a Gaussian distribution with a long tail and the maximum penetration depth is about 13.6 #mu#m for V"+ with 200 keV in cotyledon of the peanut. The experimental result of the implanted V"+ range in the peanut seeds is compared with the calculating value of the TRIM95

International Nuclear Information System (INIS)

The influence of microalloying vanadium or titanium on improving the corrosion resistance of mild steel in saturated calcium hydroxide solution was investigated. Potential-time, potentiodynamic polarization, and impedance measurement techniques were employed. The corrosion products have been examined by infrared and X-ray diffraction analysis and by scanning electron microscopy. It has been shown that the grain refining, due to microalloying, plays an important role in enhancing the corrosion resistance of steel. Scales of calcite and iron oxides on top of a protective oxide are formed on the investigated steels.

Energy Technology Data Exchange (ETDEWEB)

A process is described for making a compound selected from a crystalline spinel of the formula A/sup II/V/sub 2-x//sup III/C/sub x//sup III/O/sub 4/ formula (1) or a crystalline perovskite of the formula D/sup III/V/sub 1-y//sup III/C/sub y//sup III/O/sub 3/ formula (2) from a pentavalent vanadium compound, where A is one or more of Mg, Zn, Mn, Fe, Co, Ni, Cu and Cd; D is one ore more of Y, the rare earths and Bi; C is one or more of Al, Ga, Cr, Fe and Co, x is zero to <2, and y is zero to<1. The process comprises (1) reducing a pentavalent vanadium oxidic compound to substantially the V/sup III/ state by heating at 100/sup 0/C. or less an aqueous medium slurry or solution of the pentavalent compound containing a reducing agent selected from hydrazine and a hydrocarbylhydrazine, (2) providing in the aqueous medium either before, during or after the reducing step, A/sup II/, D/sup III/ and C/sup III/ cations in solution in the ratio called ...

International Nuclear Information System (INIS)

The "6"2Zn-"6"2Cu generator system is one of the few which yield a pure positron emitting daughter. The authors have developed a method for the preparation of this generator system following 32 MeV #alpha# particle bombardment of nickel targets. The chemical processing involves two stages: first a hydrous zirconium oxide column is used at pH 4-5 to separate the zinc and copper activities produced in the target nickel, and secondly, a conventional anion exchange column is used to retain the "6"2Zn and remove all copper activities in 2M HCl. This column serves as the "6"2Cu generator which will yield pure "6"2Cu repeatedly, free from "6"2Zn and other impurities, in a mixture of HCl and NaCl. A method is outlined also to obtain a solution of "6"2Zn using the hydrous zirconium oxide (HZO) column. "6"1Cu can be prepared as a by-product in the above procedure, but a method for the preparation of "6"1Cu alone using an 18 MeV #alpha# particle beam on a ...

International Nuclear Information System (INIS)

The hydrogen evolution reaction (HER) was studied on bare brass (B), nickel coated brass (B/Ni), nickel-zinc alloy coated brass (B/NiZn, leached Zn), nickel (under layer)/nickel-zinc alloy coated (top layer) brass electrodes (B/Ni/NiZn, leached Zn) in 1 M NaOH solution using electrolysis, cathodic polarization and electrochemical impedance spectroscopy (EIS) techniques. Long term tests were performed in order to evaluate the electrocatalytic activity and corrosion performance of the prepared electrodes with operation time. The results showed that leached electrodes, especially B/Ni/NiZn electrode, have a smaller overpotential than the others and a good electrocatalytic activity for the HER. Its electrocatalytic activity is also stable over electrolysis time. Contrary to the HER performance, B/NiZn cannot provide an adequate corrosion protection. However, when a thin Ni layer was coated under the NiZn ...

UK PubMed Central (United Kingdom)

"Fiddler's neck" is an irritant contact dermatitis that frequently affects violin and viola players. The etiology of the skin changes associated with this condition are probably attributable to a combination...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The study of passive films formed on a nickel base alloy type Inconel 600 is performed by capacitance measurements (Mott-Schottky approach). This research is supported by the passivation study of the alloying elements Ni, Cr, Fe and high purity alloys Ni-Cr, Ni-Fe, Ni-Cr-Fe. The results obtained show that the capacitive behaviour of the Inconel 600 in the passive state is similar to that on a p-n heterojunction to which a barrier zone of nickel oxide is added. The individual or combined action of alloying elements on the development of this kind of electronic structure is discussed. (authors). 5 refs., 6 figs.

Energy Technology Data Exchange (ETDEWEB)

A small scale biomass metal contacting experiment was performed to screen the optimal plant species for biosorption and bioaccumulation of cadmium, zinc, nickel, lead, and copper. Experiments were also conducted to test the ability of the biomass to lower the metal concentrations below the US Environmental Protection Agency surface water discharge criteria. The minimum residual concentration was 0.1 mg/L for zinc, 0.004 mg/L for lead, and about 0.01 mg/L for cadmium, nickel, and lead. Results indicate that water milfoil can be used for bioremoval of metals.

Energy Technology Data Exchange (ETDEWEB)

Batch and dynamic flow biosorption studies were carried out using the waste biomass entrapped in silica-gel matrix for the removal of nickel(II) ions from synthetic solutions and real wastewater. Batch biosorption conditions were examined with respect to initial pH, S/L ratio, contact time, and initial nickel ion concentration. Zeta potential measurements showed that immobilized biosorbent was negatively charged in the pH range of 3.0-8.0. The immobilized biomass was found to possess relatively high biosorption capacity (98.01 mg g{sup -1}), and biosorption equilibrium was established in a short time of operation (5 min). The equilibrium data were followed by Langmuir, Freundlich, and Dubinin-Radushkevich isotherm models. Scanning electron microscope analysis was used to screen the changes on the surface structure of the waste biomass after immobilization and nickel(II) biosorption. Sorbent-sorbate interactions were ...

International Nuclear Information System (INIS)

The feasibility of continuous production of gallium arsenide ribbon single crystals, by passage of a molten zone through boron-oxide encapsulated GaAs feedstock, is being investigated. Polycrystalline GaAs ribbons have been grown in graphite boats by passage of a wide zone through B2O3-encapsulated feed-stock, confined by a quartz cover plate. Failure to remove the encapsulant above its glass transition temperature, however, resulted in cracking of the ribbons on cooling to room temperature. In order to study the crucial zone melting step in isolation from the encapsulation steps of the continuous process, a constrained-zone melting apparatus has been constructed in which the boron oxide serves only as a sealant to suppress arsenic vaporization. Large grained polycrystalline samples have been produced with this apparatus.

International Nuclear Information System (INIS)

The concentrations of uranium, arsenic, and radium remain well below the maximum permissible values of < 0.1 mg/l (uranium), < 0.1 mg/l (arsenic) and < 100 mBq/l (radium) due to two separation stages with barium sulfate and GoPur 3000 precipitation and due to iron hydroxide/iron arsenate precipitation. The radioactive arsenates can be separated from the toxic ones by separating the sludge which is analyzed. Processing of radioactive sludges leaves reusable GoPur 3000, sulfuric solutions which contain uranium or solutions which contain carbonate, and radioactive barium sulfate whose radiation intensity of 12 mBq/g is due to the presence of radium. The sludge produced contains adsorbed salts in addition to the dosed chemicals (floated sludges: 40 g/m"3, iron sludges < 20 g/m"3). A solids content < 100 g/m"3 can be selected for both sludge portions. Static-mixer chemicals dosing and technical improvements of the tubular reactor are ...

Energy Technology Data Exchange (ETDEWEB)

By means of neutron diffraction, using the standard polycrystalline sample of Al{sub 2}O{sub 3}, measurements on three (of four spectrometers) already installed in the front of horizontal channels of MARIA reactor have been performed. Basing on these experiments as well as on activation measurements carried out earlier, the fluxes of monoenergetic neutrons have been estimated. These experiments allowed to determine (for a given geometry and kind of monochromators chosen) the resolution efficiency of instruments and high order contamination in the reflected beam. With the help of polycrystalline vanadium and TbBr{sub 3} sample, the possibility of studies using the inelastic scattering process have been tested. (author) 7 refs, 15 figs, 7 tabs

International Nuclear Information System (INIS)

The critical superconducting paramters of A-15 compounds are reviewed, and the trends analysed in order to predict maximum values. Experimental data on critical temperature is summarized and compared with theory. The ability to form the stoichiometric, well-ordered materials required for maximum Tsub(c) is discussed in terms of the thermodynamic stability of the A-15 phase. It is concluded that critical temperatures in excess of 25 K, in the A-15 structure, are unlikely. The upper critical field data show that, whereas the vanadium-based compounds are paramagnetically limited, the niobium-based compounds are not. The relation between critical current and microstructure is explored. Best data on critical current densities and ac losses is presented. Finally an account is given of the various methods by which actual conductors, both tapes and multifilamentary wires, are made. (author).

International Nuclear Information System (INIS)

EXAFS measurements are useful in determining the local atomic environment of a particular element in a solid. Since there has been some controversy about the nature of the defects produced in A-15 materials by radiation damage, such studies were carried out on some A-15 compounds, V_3Ga which was damaged by neutrons, as well as Nb_3Ge damaged by 2.5 MeV a particles. In the V_3Ga sample, site exchange disorder seems to be the most important result of the neutron damage with less than 20% of the vanadium atoms on wrong sites. However, in the Nb_3Ge samples in addition to site exchange disorder, an unusual splitting of the first near-neighbor distance between the Ge and Nb is found. This splitting, approximately 0.2 A, may explain the large Debye Waller factors observed by Burbank et al.

Energy Technology Data Exchange (ETDEWEB)

The ground state masses of thirty-nine neutron-rich nuclei from [sup 51]Ca to [sup 72]Ni have been measured using the Time-of-Flight Isochronous (TOFI) spectrometer. Eight of these masses have been measured for the first time and thirty-one are remeasurements of neutron-rich nuclei previously reported. Good agreement between these results and a previous TOFI experiment was observed except for the most neutron-rich isotopes of vanadium through iron with the present results being more bound and in better agreement with theory. The low binding energy of [sup 68]Ni, as indicated by an unreasonably low two-neutron separation energy, suggests the presence of a high-lying, long-lived isomeric state in this nucleus. (orig.)

International Nuclear Information System (INIS)

This system provides data logging facility for axial profile and dynamic profile experiments during low power physics experiments. The data from Cobalt Self Powered Neutron Detectors (SPNDs) are logged via hardware consisting of PC plug-in cards and data of vanadium SPNDs are logged from the Flux Mapping System (FMS) network (multicast data). The data along with programmable details of the experiment is transferred to an Access Database. The system provides online displays and extensive reports from the Access Database as per the requirement from Reactor Physicists. This paper briefly describes the evolvement of requirements (from the experience of operation of TAPS 4 to TAPS 3), software architecture and design. (author)

International Nuclear Information System (INIS)

From self-consistent band structure calculations using the 'augmented plane wave'(APW) method, the density of states can be decomposed into local partial (according to azimuthal quantum number l) components, the l-character densities. Within the APW formalism the intensity of X-ray emission spectra is determined by radial transition probabilities and l-character densities of such valence states, which reside inside the same atomic sphere as the core vacancy and whose quantum number l differs by +-1 from the one corresponding to the core state. By taking into account lifetime broadening of the core and valence states and also the instrumental broadening the computed spectra (non-metal K-, vanadium K- and Lsub(III)-spectra) agree well with experiment. (orig.).

International Nuclear Information System (INIS)

A discussion is given concerning the transformation in acid medium of curite into copper-, nickel- and cobalt-uranylphosphate. From chemical, differentiel thermal and thermogravimetric analyses, the crystal-chemical formula are calculated as: Cu(UO_2/PO_4)_2.8H_2O, Ni(UO_2/PO_4)_2.7H_2O and Co(UO_2/PO_4)_2.7H_2O. The two last compounds crystallize in the triclinic system with space group P1 or P1(overscore) and the first one crystallizes in the tetragonal system with space group P4/nmm. The cell parameters are calculated. From solubility data, the solubility products are computed as 10sup(-12.8), 10sup(-9.5) and 10sup(-9.9) for the copper-, nickel- and colbalt-compound respectively. The electrokinetic properties of the three species are closely similar to those of natural meta-torbernite: the zeta-potential is negative and the point of zero charge be reached cannot in the pH-range 2 to 9.

Energy Technology Data Exchange (ETDEWEB)

One of the most loaded parts of a steam generator of VVER 440 MW type are the bolts and thread holes of the primary collector cover sealing set. The strength calculations and tensometric measurings performed during operation proved the high degree of a load on the bolts. The conditions of the stress limitation are not met in some cases according to the pertinent standards. The untightnesses at nickel rings occurred during putting the units of Jaslovske Bohunice and Dukovany nuclear power stations into operation. With regard to improve the reliability, the producer has taken measures to improve the quality of the rings and users have introduced more strict regulations for bolts tightening. Due to these measures the high reliability of the set has been obtained from point of view of the tightness, but substantial reduction of bolts and holes threads loading have not been obtained. Several years operation experience proved relatively low service of bolts, damage of ...

Energy Technology Data Exchange (ETDEWEB)

This study deals with a research field started at the LFI (Laboratorio de Fabricacion Integrada) of the ULPGC (Universidad de Las Palmas de Gran Canaria). Its aim is to analyse and propose improvements in the electroformed nickel cores manufacture. The main application of these cores is to be used as plastic injection molds. It has been considered an important part of this study taking under consideration internal stresses that appear in the nickel electroformed core. These stresses play a determinant role towards reaching a dimensional and resistant quality standard of the shells, which will be later transformed into cores. The investigation includes not only a theoretic study but also an experimental one. the testing method has the remarkable advantage of a wide industrial application because of its simplicity, low cost and reproducibility of the electrolytic bath actual conditions. (Author) 7 refs.

Science.gov (United States)

The authors develop a procedure for the determination of the Al, Ti, V, Cu, Mn, Mo, and W content of nickel-base alloys by neutron activation analysis. An M-10 microtron with a beryllium target in a paraffin microtron (with a beryllium target) in a paraffin moderator served as the neutron source. In order to evaluate the procedure for quantitative analysis, the authors determined the contents of the above elements in five reference standards, the bulk density of which was 2.94-4.17 g/cm/sup 3/. The difference in the self-absorption of the gammaquanta was assessed by determining the number of gamma-quanta with energies in the range 60-1332 keV that had passed through the RS N4 and N8 which showed the greatest difference in their composition. The results of the determination are presented. The proposed procedure is simple and rapid and can be used to determine the alloying components of nickel-based alloys with satisfactory precision.

International Nuclear Information System (INIS)

Rapid corrosion of PWR steam generator carbon steel support structures and consequential denting of steam generator tubes led to considerable investigation of the mechanism of corrosion and for palliatives. The basic mechanism is now fairly well understood. Chloride present in the boiler feedwater from condenser leakage is concentrated in the support plate crevice as a result of the superheat present. This leads to the formation of a low pH acid ferrous chloride environment either through the hydrolysis of a weak base chloride such as MgCl_2 or the combined action of a neutral chloride with an oxidizing agent. Rapid attack of the carbon steel ensues with the Fe_3O_4 corrosion product forming at the metal/oxide interface. This oxide has a volume approximately twice that of the steel consumed and thus eventually fills the crevice between the tube and the support plate. Oxide growth continues leading to compression of the Alloy 600 primary tube and to distortion and eventual fracturing of ...

Energy Technology Data Exchange (ETDEWEB)

The present paper is a comparative study of the cerium-containing nickel catalysts supported on x- and y-zeolites. In general, the addition of cerium ions caused an increase in the catalytic activity for CO hydrogenation and shifted the product selectivity to high molecular weight hydrocarbons. The degree of the effect of cerium additive depends on the ratio of cerium to nickel contents, the reduction temperature, and the nature of the supporting materials. Catalyst characterization, including volumetric hydrogen chemisorption, temperature programmed reduction/desorption, x-ray diffraction, surface area measurements, in-situ infrared spectroscopy and x-ray photoelectron spectroscopy, was performed in order to interpret the phenomena due to the effects of cerium additives and the support effect on Ni/zeolite catalysts.

Energy Technology Data Exchange (ETDEWEB)

Biosorption behaviour of and toxic effects of heavy metals in submersed and immobilised microorganisms was studied in batches and in continuous processes in an airlift-recycle reactor. Nickel, cadmium, and zinc were used as heavy metals. (orig./VHE) [Deutsch] Am Beispiel einer Naphthalin-2-sulfonsaeure-abbauenden Kultur wurde das Biosorptionsverhalten und die toxische Wirkung von Schwermetallen auf submerse und immobilisierte Mikroorganismen im Batch-Ansatz und im kontinuierlichen Betrieb in einem Airlift-Schlaufenreaktor untersucht. Als Schwermetalle wurden Nickel, Cadmium und Zink eingesetzt. (orig./VHE)

International Nuclear Information System (INIS)

Radioactive "3"1Si was used as a tracer to study silicon self-diffusion in thin film silicides of cobalt, nickel, palladium and platinum. The specimens were prepared by sequential electron beam evaporation of radioactive "3"1Si and of the metal onto cleaned silicon wafers. By vacuum annealing at the appropriate formation temperature a silicide about 250 nm thick containing a sharp radioactive band about 50 nm thick was generally formed. Subsequent heating above the formation temperature resulted in a spreading of the activity owing to silicon self-diffusion. Activity profiles in the silicides were measured by a combination of ion beam sputtering, radioactivity counting and Rutherford backscattering of charged nuclear particles. (orig.).

International Nuclear Information System (INIS)

The nickel-rich superalloys Alloy 600 and Alloy 800 have been corroded in mildly alkaline deuterated aqueous conditions typical of secondary coolant circuits in a nuclear power station. The oxide films and substrates of these alloys have been analysed by imaging SIMS depth profiling, which makes it possible to describe elemental distribution in all three dimensions. The measurement of the distribution of the secondary ions NiO"-, FeO"- and CrO"- appears useful for detailing the behaviour of nickel, iron and chromium within oxidized phases. The measurement of D"- distribution outlines the extent of oxide hydration. For Alloy 800, evidence of sodium migration into the grain boundaries of the alloy substrate is found. For Alloy 600, no grain boundary sodium ingress can be identified under comparable corrosion conditions. (author).

British Library Electronic Table of Contents (United Kingdom)

We present a novel fabrication route yielding Raney-platinum film electrodes intended as glucose oxidation anodes for potentially implantable fuel cells. Fabrication roots on thermal alloying of an extractable metal with bulk platinum at 200^oC for 48h. In contrast to earlier works using carcinogenic nickel, we employ zinc as potentially biocompatible alloying partner. Microstructure analysis indicates that after removal of extractable zinc the porous Raney-platinum film (roughness factor ~2700) consists predominantly of the Pt3Zn phase. Release of zinc during electrode operation can be expected to have no significant effect on physiological normal levels in blood and serum, which promises good biocompatibility. In contrast to previous anodes based on hydrogel-bound catalyst particles the ...

British Library Electronic Table of Contents (United Kingdom)

The present study was aimed at investigating effects of nickel (NiCl2) on secretion of testosterone (T), cell viability, ultrastructure and apoptosis in mouse Leydig cells. Testosterone release was measured after 48h of culture with 15.67, 31.25, 62.5, 125, 250, 500 and 1000mmol/L NiCl2 or without NiCl2 using radioimmunoassay. Cell viability was assessed by a MTT (metabolic activity assay). Quantification of apoptotic cells was performed using TUNEL assay and the ultrastructural changes were analyzed using transmission electron microscopy. The viability was decreased after addition of >=250mmol/L NiCl2. A concentration-dependent depression of T production was observed. The percentage of apoptotic cells was significantly increased only after addition of 125, 250 and 1000mmol/L NiCl2. After ...

Energy Technology Data Exchange (ETDEWEB)

Chars prepared from potassium-exchanged carboxy methyl cellulose at several heat treatment temperatures (HTTs) were gasified in air isothermally at selected gasification temperatures (GTs) in the range 633-893 K to investigate the catalytic effectiveness of potassium species. The chars displayed a noticeable jump in gasification rate at a particular gasification temperature (called jump temperature, T{sub j}). The magnitude of jump was much less than that reported for copper and nickel catalysis, but comparable with that for calcium catalysis. Increase in HTT caused a decrease in the jump temperature of chars in contrast with the increase observed in copper, nickel and calcium catalysis; also the magnitude of jump did not decrease, but remained unaltered, on increasing HTT. The different behavior of potassium catalysis is correlated to a change in the chemical state of potassium at higher HTT. The results reveal the dependence of jump ...

International Nuclear Information System (INIS)

A ternary nickel-base alloy Ni-W-B has been developed for surface corrosion and wear resistance to replace chromium plating, which uses environmentally hazardous solutions. The deposition conditions used an alkaline bath and insoluble anodes. The as-deposited alloy typically contains 40 wt% W and 1 wt% B and has an amorphous or partially amorphous structure. These deposits compare favorably with hexavalent chromium deposits in throwing power, color uniformity, and reflectivity. The corrosion resistance of Ni-W-B alloy was compared with hexavalent chromium and electroless nickel deposits in a variety of acids, including hydrochloric, sulfuric, fluoroboric, and phosphoric. In all cases, best results were obtained with the Ni-W-B deposits.

Energy Technology Data Exchange (ETDEWEB)

An apparatus is described for measuring the total hemispherical emittance of pipes of a length suitable for use in a prototype solar collector. The calorimetric method used requires measurements of the temperatures of the surface of the test pipe and of a concentric outer cylinder and measurement of the electrical power used to heat the test pipe. Measurements were made of the total hemispherical emittance of black chrome, nickel, and bare steel pipes as a function of temperature. The emittance of the black chrome surfaces increased significantly from an extrapolated value of about 0.1 at 25 deg C to values on the order of 0.3-0.4 at 300 deg C. The extrapolated values for black chrome agreed with measurements made using other techniques at room temperature. The results for the nickel-plated pipe agreed with total emittance calculated from spectral reflectance data.

Energy Technology Data Exchange (ETDEWEB)

This patent describes the vapor phase catalytic dehydrogenation of a C/sub 2/-C/sub 4/ paraffin by contacting the paraffin with a spinel of the formula A/sup III/V/sub 2-x//sup III/C/sub x//sup III/O/sub 4/, formula (1) or a crystalline perovskite of the formula D/sup III/V/sub 1-y//sup III/C/sub y//sup III/O/sub 3/, formula (2) where A is one or more of Mg, Zn, Mn, Fe, Co, Ni, Cu and Cd; D is oone of more of Y, the rare earths and Bi; C is one or more of Al, Ga, Cr, Fe and Co, x is zero to < 1.9, and y is zero to < 0.9, which spinel or perovskite is made by a process which comprises (1) reducing a pentavalent vanadium oxidic compound to substantially the V/sup 111/ state by heating at 100/sup 0/C or less an aqueous medium slurry of solution of the pentavalent compound containing a reducing agent selected from hydrazine and a hydrocarbylhydrazine, (2) providing in the aqueous medium ether before, during or after the reducing step, A/sup II/, D/sup III/ and ...

Energy Technology Data Exchange (ETDEWEB)

A borohydride, for instance sodium borohydride, is added to the radioactive effluent, with eventually a carrier such as Cu{sup +}, to give a precipitate containing ruthenium. The processing can be combined to Sr and Cs precipitation be know processes giving barium sulfate and nickel ferrocyamide precipitates. Influence of borohydride concentration on decontamination factor is given.

Energy Technology Data Exchange (ETDEWEB)

Spherical {beta}-Ni(OH){sub 2} was modified by a low-cost method of normal ball milling (NBM), and the physical properties of both ball-milled and un-milled Ni(OH){sub 2} were characterized by transmission electron microscopy, specific surface area, particle size distribution and X-ray diffraction. It was found that NBM could obviously increase the surface area, decrease the particle and crystallite size, and reduce the crystallinity of {beta}-Ni(OH){sub 2}, which were advantageous to the improvement of the electrochemical activity of Ni(OH){sub 2}. NBM also lowered the packing density and flowability of Ni(OH){sub 2}, as revealed by the measurements of tapping density and angle of repose. Electrochemical performances of pasted nickel electrodes with an addition of ball-milled Ni(OH){sub 2} to spherical Ni(OH){sub 2} as the active material were investigated, and were compared with those of the pure spherical Ni(OH){sub 2} electrodes. Charge/discharge tests showed ...

Energy Technology Data Exchange (ETDEWEB)

This paper investigates the dynamic recrystallization behavior of a directionally solidified (DS) nickel-base superalloy. The dynamic recrystallization occurs after the uncoated superalloy has been tested by tensile creep at elevated temperature for a long time. The dynamic recrystallization temperature is slightly lower than that of the static recrystallization. The dynamic recrystallization behavior of the DS superalloy below the static recrystallization temperature is mainly related to the high temperature oxidation and the free surface. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

The isomeric composition of bicyclo(3.3.1)nonadienes was investigated by GLC and PMR spectroscopy with silver-lanthanide shift reagents. The absence of stereospecificity in the hydrogenation of 3,7-dimethylenebicyclo(3.3.1)nonane by hydrogen adsorbed on Raney nickel was demonstrated. This is explained by the sequence of the isomerization and then hydrogenation processes.

Science.gov (United States)

An instrument has been constructed for the measurement of residual stress in steel. If necessary, large objects can be examined in situ. An account is given of the principles and construction. A special stressing frame provides for calibration. An application to residual stress in gear blanks has established a systematic variation of surface stress with nickel content and confirmed the overall effect of the surface hardening treatment.

Energy Technology Data Exchange (ETDEWEB)

Nickel-titanium alloys may coexist in more than one crystalline structure. There is a high temperature phase, austenite, and a low temperature phase, martensite. The metallurgical basis for the superelasticity and the shape memory effect relies in the ability of these alloys to transform easily from one phase to another. There are three essential factors for the orthodontist to understand nickel-titanium alloys behaviour: stress; deflection; and temperature. These three factors are related to each other by the stress-deflection, stress-temperature and deflection-temperature diagrams. This work was undertaken with the objective to analyse commercial nickel-titanium alloys for orthodontics application, using the dynamical mechanical analyser - DMA. Four NiTi 0,017 X 0,025'' archwires were studied. The archwires were Copper NiTi 35 deg C (Ormco), Neo Sentalloy F200 (GAC), Nitinol Superelastic (Unitek) and ...

Energy Technology Data Exchange (ETDEWEB)

This decision document presents the selected remedial action for the Ruston/North Tacoma Study Area, in Ruston and Tacoma, Washington. The EPA has divided the Commencement Bay/Nearshore Tideflats Superfund site into seven operable units (OU's) in order to facilitate the investigation, analysis, and cleanup of this very large site. Four of these OU's are associated with the Asarco smelter: OU 02 - Asarco Tacoma Smelter; OU 04 - Asarco Off-Property (Ruston/North Tacoma Study Area); OU 06 - Asarco Sediments; and OU 07 - Asarco Demolition. The remedy described in this ROD addresses OU 04 and involves the cleanup of arsenic and lead contaminated soils and slag in the Study Area, the residential community surrounding the smelter. This remedy will address the principal threat posed by conditions at the site, which is the ingestion of contaminated soil and dust.

Energy Technology Data Exchange (ETDEWEB)

The surface coverage of amorphous silica gels used in the synthesis of silica polyamine composites has been investigated by 29Si NMR. By diluting the polyamine anchor silane, chloropropyl trichlorosilane, with methyl trichlorosilane it was found that surface coverage could be markedly improved for a range of amine polymers after grafting to the silica surface. The commensurate decrease in the number of anchor points and increase in the number of free amines results in an increase in metal capacity and/or an improvement in capture kinetics. Solid state CPMAS-13C NMR has been employed to investigate the structure and metal ion binding of a series of these composite materials. It is reported that the highly branched polymer, poly(ethyleneimine) (PEI) exhibits much broader 13C NMR resonances than the linear polymers poly(allylamine) (PAA) and poly(vinylamine) (PVA). These results are understood in terms of the low energy conformations calculated from molecular modeling studies. Three new ...

International Nuclear Information System (INIS)

A set of equations describing a stress-mediated evolution of the nonequilibrium dopant-defect system has been derived and analyzed. Together with coupled diffusion of dopant atoms and point defects, we consider the drift of all mobile species in different charge states, namely vacancies, self-interstitials, and pairs 'dopant atom-point defect', in the field of stress. It has been shown that stresses may affect the diffusion of dopant atoms mainly in two ways: (1) directly, due to the drift of the pairs in the field of stress; (2) indirectly, by the formation of nonuniform defect distribution due to the drift of point defects. On this basis, various features of doping processes, such as phenomena of 'uphill' impurity diffusion near the surface (within the framework of the first or second mechanisms) and the peculiarities of high concentration phosphorus diffusion (due to the second mechanism), can be explained. Numerical computations of high concentration phosphorus diffusion in silicon ...

International Nuclear Information System (INIS)

We have measured the lattice relaxation around As in Si at a homogeneous As concentration of 4x10"1"8 cm"-"3 by EXAFS spectroscopy. From the absorption spectra, distances up to the 4th shell could be extracted. A sizeable misfit due to an increased distance is only observed for the 1st shell. Complementing our experimental work we have performed ab initio calculations based on the density functional theory with the WIEN97 package which uses the linearised augmented plane wave method and with the FHI96md program which uses first-principles pseudo-potentials and a plane wave basis set to investigate the size dependence of the super-cells constructed around one substitutional As atom. The calculations yielded good agreement with our EXAFS experiment so that the determined relaxations can be used as a solid basis for further interpretations of derived parameters such as hyperfine interaction parameters in defect complexes.

International Nuclear Information System (INIS)

(001) CZ silicon wafers were implanted with arsenic (As"+) at energies of 10--50 keV to doses of 2 x 10"1"4 to 5 x 10"1"5/cm"2. All implants were amorphizing in nature. The samples were annealed at 700 C for 16 hrs. The resultant defect microstructures were analyzed by XTEM and PTEM and the As profiles were analyzed by SIMS. The As profiles showed significantly enhanced diffusion in all of the annealed specimens. The diffusion enhancement was both energy and dose dependent. The lowest dose implant/annealed samples did not show As clustering which translated to a lack of defects at the projected range. At higher doses, however, projected range defects were clearly observed, presumably due to interstitials generated during As clustering. The extent of enhancement in diffusion and its relation to the defect microstructure is explained by a combination of factors including surface recombination of point defects, As precipitation, As clustering and end of range damage.

International Nuclear Information System (INIS)

A unified physically based ion implantation damage model has been developed which successfully predicts both the impurity profiles and the damage profiles for a wide range of implant conditions for arsenic, phosphorus, BF_2, and boron implants into single-crystal silicon. In addition, the amorphous layer thicknesses predicted by this new damage model are also in excellent agreement with experimental measurements. This damage model is based on the physics of point defects in silicon, and explicitly simulates the defect production, diffusion, and their interactions which include interstitial-vacancy recombination, clustering of same type of defects, defect-impurity complex formation, emission of mobile defects from clusters, and surface effects for the first time. New computationally efficient algorithms have been developed to overcome the barrier of the excessive computational requirements. In addition, the new model has been incorporated in the UT-MARLOWE ion ...

Energy Technology Data Exchange (ETDEWEB)

This Corrective Action Decision Document/Closure Report (CADD/CR) has been prepared for Corrective Action Unit (CAU) 409: Other Waste Sites, Tonopah Test Range (TTR), Nevada, in accordance with the Federal Facility Agreement and Consent Order. Located near Area 3 on the TTR approximately 140 miles northwest of Las Vegas, Nevada, CAU 409 is comprised of three Corrective Action Sites (CASs): CAS RG-24-001-RGCR, Battery Dump Site; CAS TA-53-001-TAB2, Septic Sludge Disposal Pit (referred to as Septic Sludge Disposal Pit No.1); CAS TA-53-002-TAB2, Septic Sludge Disposal Pit (referred to as Septic Sludge Disposal Pit No.2). This CADD/CR identifies and rationalizes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Operations Office's (NNSA/NV's) recommendation that no corrective action is deemed necessary for CAU 409. The CADD/CR have been combined into one report based on sample data collected during the field investigation performed in ...

Science.gov (United States)

Superconductivity of binary alloys spanning the A-15 compounds V/sub 3/Si, V/sub 3/Ge, V/sub 3/Ga, and V/sub 3/Al and the pseudobinary derivatives of these stoichiometric compounds was surveyed by studying samples prepared by rf-sputtering from alloy cathodes. The possible formation of the hypothetical A-15 binaries ''V/sub 3/P,'' ''V/sub 3/B,'' and ''V/sub 3/C'' and their pseudobinary formation with V/sub 3/Si was also explored. Efforts to form these hypothetical alloys were not successful. The T/sub c/'s were measured resistively and the structure and lattice constants were determined by x-ray analysis. A maximum T/sub c/ of 11.7/sup 0/K was obtained for A-15 V/sub 3/Al, and the importance of a suitable deposition temperature and high sputtering pressures was examined. It is proposed that large variations of T/sub c/ among pseudobinary alloys imply a rapid variation of ...

Science.gov (United States)

Certain materials, especially Sn, passivate the rare earth-exchanged Y zeolite (REY) used in petrochemical fluid-cracking catalysts against vanadium degradation caused by V impurities in the feed oil. The mechanism of passivation was investigated here from the standpoint of high-temperature oxide acid-base reaction; i.e., where the controlling factors were considered to be Lewis acid-base reactions between V{sub 2}O{sub 5}, the RE oxides, SnO{sub 2}, etc. Molten salt tests at 680{degree}C showed SnO{sub 2}, presumably because of its acidic nature, to be essentially nonreactive with V{sub 2}O{sub 5} or Na{sub 2}O-V{sub 2}O{sub 5} compounds. A hypothesis was developed to explain how the passivation effect by Sn might result from the unique resistivity of SnO{sub 2} to reaction with V{sub 2}O{sub 5}.

International Nuclear Information System (INIS)

The resonance line shift of a series of A-15 structures (V_3Pt, Vsub(0.76)Ptsub(0.24) and Vsub(0.62)Irsub(0.38) is measured as a function of temperature in the superconducting state. A method will be described to separate the contribution of the diamagnetism of the superconductor (Meissner effect) and that of the Knight shift to this line shift. From the temperature dependence of the Knight shift of the V atoms the sum of the s and d contribution to the Knight shift can be determined. In these three compounds the s and d contributions appear to cancel out nearly. Moreover the temperature dependence of kappa_2 can be calculated from the measurements. The values of kappa_2 extrapolated at T=Tsub(c) are about 70 for these samples. From the obtained sum of Ksub(s) and Ksub(d) and the data of the susceptibility or of the specific heat of these samples Ksub(s) and Ksub(d) can be separated. For all samples Ksub(s)=0.06+-0.005%. Finally it was observed that the quadrupolar interaction ...

Energy Technology Data Exchange (ETDEWEB)

With regard to long-term high-temperature strength, molybdenum is an effective alloying element but rather expensive as well. The author describes its influence on high-temperature strength properties of CrMoV alloyed steel. Besides molybdenum, also vanadium and carbon have an increasing effect on limiting rupture stress which furthermore may be effected by heat treatment, the cooling rate being a dominating factor in this process. To guarantee optimum long-term high-temperature strength properties, a minimum of a least 0.5% Mo and 0.35% V is required. The cooling rate after austentizing must be high enough to enable transformation in the bainitic structure to take place. A two-to-three-hour tempering treatment at about 720/sup 0/C is regarded as an optimum.

Energy Technology Data Exchange (ETDEWEB)

A new preparation method for LiNiVO{sub 4} has been developed. LiNiVO{sub 4} can be readily obtained from the solid state reaction of LiNiO{sub 2} and V{sub 2}O{sub 3} or V{sub 2}O{sub 5} at 700 C for 2 h in air. The quarternary Li-Ni-V-O reaction is strongly dependent on vanadium starting materials, reaction environment atmosphere, reactant stoichiometry and synthesis temperature. Individual particles of LiNiVO{sub 4} powders are well-formed crystallites shown clearly by scanning electron microscopy results to be in the shape of an octahedron. Powder X-ray diffraction studies of this crystalline material indicate that LiNiVO{sub 4} has an inverse spinel structure different from that of known cathode materials such as LT-LiCoO{sub 2} and LiMn{sub 2}O{sub 4}. The Li/LiNiVO{sub 4} cell can be charged and discharged at about 4.8 V versus metallic Li. To our knowledge, this is the Li intercalation reaction with the highest voltage known. (orig.) 14 refs.

Energy Technology Data Exchange (ETDEWEB)

The influences of temperature and duration of tempering on hardness and microstructure were investigated at high-temperature martensitic and low-carbon steels with 9% chrome and the further alloying elements molybdenium, vanadium, niobium and partially tungsten. After austenitizing and subsequent air cooling the steels were tempered at temperatures below, at and above Ac{sub 1b} for different times and finally a hardness test was performed. Making use of the temperature dependence of the hardness tempering diagrams were constructed and the Hollomon-Jaffe-Parameter on the three steels was determined within its application limits. Micrographs of the structure shows the formation of the carbides and the martensite. At tempering temperatures below Ac{sub 1b} a decrease of hardness occurs, above Ac{sub 1b}, a hardness rise due to the partial austenitizing was obtained. While hardening below Ac{sub 1b}, the tempering quality increases from P 91, NF 616 to E 911. (orig.) ...

International Nuclear Information System (INIS)

Several metallurgical coatings have been developed that provide good tribological performances in high-temperature liquid sodium and that are relatively unaffected by neutron fluences to 6 X 10/sup 22/ n/cm/sup 2/ (E > 0.1 MeV). The coatings that have consistently provided the best tribological performance have been the nickel aluminide diffusion coatings created by the pack cementation process, chromium carbide or Tribaloy 700 trade mark (a nickel-base hardfacing alloy) applied by the detonation-gun process, and chromium carbide and other hardfacing alloy) applied by the detonation-gun process, and chromium carbide and other hardfacing materials applied by the electro-spark deposition process. The latter process is a relatively recent development for nuclear applications and is expected to find wide usage. Other coating processes, such as plasma-spray coating, sputtering, and chemical vapor deposition, were candidates for use on various ...

International Nuclear Information System (INIS)

Yield stress elevations (#DELTA##sigma#_y) in pressure vessel steels irradiated at intermediate flux and fluence systematically decreased with increasing temperature and decreasing copper and nickel content. Lower stress relief temperature also decreased #DELTA##sigma#_y at bulk copper concentrations greater than about 0.3%. The dependence of #DELTA##sigma#_y on irradiation temperature between 260 and 316 C increased with copper and nickel content and decreased with phosphorus content. When normalized by the average #DELTA##sigma#_y, the fractional temperature dependence correlates with a simple empirical chemistry factor of copper and phosphorus. The correlation predicts data on the irradiation temperature dependence of #DELTA##sigma#_y found in the literature within a standard error of about 0.3 MPa/degree C and is consistent with current understanding of hardening mechanisms. However, questions remain about the effects at very low flux and ...

International Nuclear Information System (INIS)

Based on information contained in literature, patents and catalogs a review is presented of powder-rolling metallurgy abroad. Statistics are given on the output of powder metallurgy in several countries. In the USA both the dense type of rolled metal for manufacturing various machine parts and the porous variety for making filters are produced. Four main types of technological processes are analysed: the usual flow chart for cold rolling, rolling of preheated powder, rolling in free-flowing state, and rolling with heated rollers. Of these four processes the first is most widely used. Fowders consisting of spherical particles (heat-stable alloys from nickel or high titanium alloys), which are difficult to work with, have not yet found wide practical application in powder metallurgy abroad. Literature data show that granulated heat-resistant alloys can be cold-treated under pressure only after they are powdered. The best methods for pulverizing are: cold-stream ...

Energy Technology Data Exchange (ETDEWEB)

In our continued efforts for improving the performance of zinc anodes for a Zn/air battery, we now report the preparation of three alloys and improved performances of anodes made up with these alloys. The alloys contained zinc, nickel, and indium with different weight percentages and were calcined at two different temperatures. Out of the six alloys, the alloy which has a composition of zinc 90%, nickel 7.5% and Indium 2.5% and fired at 500{sup o}C is found to be the best. In the case of the hydrogen evolution reaction, this alloy had its potential shifted to a more negative potential. As far as the cyclic voltammograms were concerned, the difference between the anodic and cathodic part was minimal when compared with other alloys. Surprisingly, this alloy had reversibility even after 100 cycles of the cyclic voltammogram. This is a clear indication that dendrite formation was reduced to a considerable extent. Images taken with a scanning ...

International Nuclear Information System (INIS)

Topics related to aerospace power are discussed, taking into account trends and issues of military space power systems technology, space station power system advanced development, the application and use of nuclear power for future spacecraft, the current status of advanced solar array technology development, the application of a parabolic trough concentrator to space station power needs, life test results of the Intelsat-V nickel-cadmium battery, and metal hydride hydrogen storage in nickel hydrogen batteries. Other subjects explored are concerned with alternative fuels, biomass energy, biomedical power, coal gasification, electric power cycles, and electric propulsion. Attention is given to an advanced terrestrial vehicle electric propulsion systems assessment, fuel cells as electric propulsion power plants, a sinewave synthesis for high efficiency dc-ac conversion, steam desulfurization of coal, leadless transfer of energy into the body to ...

International Nuclear Information System (INIS)

Fe-Cu binary alloys are often used to mimic the behaviour of reactor pressure vessel steels. Their study allows identifying some of the defects responsible for irradiation-induced hardening. But recently the influence of manganese and nickel in low-Cu steels has been found to be important as well. In contrast with existing models found in the literature, which predict that hardening saturates after a certain dose, Fe alloys containing nickel and manganese irradiated in a material test reactor (BR2) show a continuous increase of hardening, up to doses equivalent to about 40 years of operation. Considerations based on positron annihilation spectroscopy analyses suggest that the main objects causing hardening in Cu-free alloys are most probably self-interstitial clusters decorated with manganese. In low-Cu reactor pressure vessel steels and in Fe-CuMnNi alloys, the main effect is still due to Cu-rich precipitates at low doses, but the role of ...

International Nuclear Information System (INIS)

The effects of key metallurgical variables on the low fluence hardening in a set of A533B model steels were evaluated over a wide range of irradiation temperatures. Above about 163 degrees C hardening increased with higher copper and nickel contents, as is typical of the pressure vessel operating regime around 290 degrees C. However, at 121 degrees C the hardening was generally lower and unaffected by copper and nickel variations. This observation of decreased hardening with lower temperature (e.g. an open-quotes invertedclose quotes temperature dependence) is tentatively attributed to a reduced contribution of copper precipitation. Tensile data for a set of commercial steels with a range of (uncontrolled) compositions also showed minimal sensitivity to copper variations at 121 degrees C. Unlike the hardness data no systematic reductions in the yield stress increases were observed between 163 and 121 degrees C. However, the ultimate tensile ...

Energy Technology Data Exchange (ETDEWEB)

Degradation reactions of a nylon 6 battery separator material have been studied in 4-34% aqueous KOH electrolytes at 35/sup 0/-110/sup 0/C. In a Ni/Cd cell, this degradation involves a slow hydrolysis reaction followed by fast electrochemical oxidations of the hydrolysis reaction products. Arrhenius activation energy of the hydrolysis reaction in 34% KOH was 20.0 +- 0.3 kcal/mole. A plot of the hydrolysis rate at 100/sup 0/C vs. hydroxyl ion concentration gave a rate maximum at about 16% KOH, and the mechanism for this effect is discussed. Electrochemical oxidations of the hydrolysis product, 6-aminocaproate ion, appear to proceed rapidly in several sequential steps at a nickel oxide electrode. In a Ni/Cd cell, the combination of nylon separator hydrolysis followed by electrochemical oxidation of the products can seriously degrade the battery lifetime. The rate of the hydrolysis of nylon 66 separator material was approximately one half of that of the nylon 6 ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is to combine the MCFC cathode Li{sub x}Ni{sub 1-x}O properties to those of the protective coatings of LiCoO{sub 2}, Li{sub 2}TiO{sub 3} or of CeO{sub 2}, less soluble in the molten carbonates. In the cases of LiCoO{sub 2}, have been carried out by controlled potential coulometry in aqueous solution, a deposition of Co{sub 3}O{sub 4} on dense Ni. The cobalt oxide reacts rapidly in the Li{sub 2}CO{sub 3}-Na{sub 2}CO{sub 3} medium at 650 C to give LiCoO{sub 2}, a spinel cubic phase revealed by Raman spectroscopy. (O.M.)

Energy Technology Data Exchange (ETDEWEB)

Apparent molar volumes V{sub phi} and apparent molar heat capacities C{sub p,phi} were determined for aqueous solutions of nickel(II) nitrate, copper(II) nitrate, and zinc(II) nitrate at molalities m=(0.01 to 0.5) mol {center_dot} kg{sup -1}, and at the pressure p=0.35 MPa. Solution densities obtained using a vibrating-tube densimeter at T=(278.15 to 368.15) K were used to calculate V{sub phi} values. Heat capacity measurements obtained with a twin fixed-cell, differential-output, power-compensating, temperature-scanning calorimeter at T=(278.15 to 393.15) K were used to calculate values of C{sub p,phi}. Our results were then fitted to functions of m and T and compared to literature values.

Science.gov (United States)

Solid solution-strengthened nickel base alloys have been used for nuclear stream generator tubing in pressurized water reactors since the beginnings of commercial nuclear power. The purpose of this paper is to recap and update the authors understanding of the relationship between processing, resulting structure, and properties for Alloy 600 and to discuss the requirements for optimized performance in both primary and secondary environments. Potential replacement materials and their performance will be discussed. Also discussed is the role and importance of system chemistry, bulk and local, and control and its relationship to performance. A discussion of potential mechanisms of environmentally assisted failure is also discussed.

International Nuclear Information System (INIS)

A few metal complexes of isatin-isonicotinoylhydrazone with Ni(II), Cr(III), Co(II), Cu(II), Zn(II) and Cd(II) have been prepared and characterized on the basis of elemental analyses, infrared and electronic spectra as well as "1H NMR spectra, conductivity and magnetic measurements. In view of the results obtained, it has been found that two molecules of isatin-isonicotinoylhydrazone are chelated to the central metal ion as bis-uninegative ONO tridentate ligand forming non-electrolytic octahedral metal complexes. (author)

International Nuclear Information System (INIS)

A number of herbal drugs are used in the Unani (Greco-Arab) System of Medicine for cardiovascular diseases. The herbs were analyzed by flame AAS and ICP-AES to determine if their therapeutic actions can be associated with the elements present in them. Cadmium, cobalt, chromium, copper, iron, potassium, magnesium, manganese, sodium, nickel, phosphorus, lead and zinc were some of the elements which play various roles in cardiovascular affections. An effort was made to correlate the role of these elements in cardiac diseases. (Auth.). 2 tabs., 32 refs.

Energy Technology Data Exchange (ETDEWEB)

The present invention provides a compound of the formula (Cat).sup.+.sub.z[M.sup.++(5-nitro-1H-tetrazolato-N2).sup.-.sub.x(H.sub.2- O).sub.y] where x is 3 or 4, y is 2 or 3, x+y is 6, z is 1 or 2, and M.sup.++ is selected from the group consisting of iron, cobalt, nickel, copper, zinc, chromium, and manganese, and (Cat).sup.+ is selected from the group consisting of ammonium, sodium, potassium, rubidium and cesium. A method of preparing the compound of that formula is also disclosed.

Energy Technology Data Exchange (ETDEWEB)

Thin films of La{sub 0.6}Ca{sub 0.4}CoO{sub 3} perovskite were deposited on nickel plates by thermal decomposition of the metal nitrates. The electrochemical activity of the films for oxygen evolution in KOH solutions (0.1-1 M) was investigated. The reaction order with respect to OH{sup -} ion was found to be around 0.7. The results correlate fairly well with a mechanism in which breaking of the intermediate metal-peroxide bond at the Co ion is the rate-determining step. (author) 4 figs., 4 refs.

Energy Technology Data Exchange (ETDEWEB)

A process for the production of transportation fuels from heavy hydrocarbonaceous feedstock is provided comprising a two-stage, close-coupled process, wherein the first stage comprises a hydrothermal zone into which is introduced a mixture comprising a feedstock and metals-impregnated red mud having coke-suppressing and demetalizing activity, and hydrogen; and the second, close-coupled stage comprises a hydrocatalytic zone into which substantially all the effluent from the first stage is directly passed and processed under hydrocatalytic conditions. The preferred metals for impregnation include transition metals, in particular, nickel and molybdenum.

Energy Technology Data Exchange (ETDEWEB)

The report covers the results of exposing materials for steam turbines to increased steam temperatures in two modules of the KOMET 650 testing facility at the Westfalen power plant. Ferritic/martensitic steels with 9 to 12% Cr and austenite and nickel-based alloys were investigated. Some experimental coatings on low-alloy Cr steel were also tested. The principal findings are presented. It will become possible to construct advanced power stations to be operated at higher temperatures. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Directionally solidified nickel-based superalloy DZ4 is an important structural material. However, the grinding burn occurs in grinding processes has hindered the grinding efficiency and dimensional accuracy. This paper investigates the grinding mechanism of this new type of superalloy based on the systematical analyses of variable characteristics of the grinding force, grinding temperature, topography of ground surface, hardness distribution of surface layer, as well as morphology of surface layer from a metallographical point of view. The results will be beneficial to grinding the superalloy with high efficiency and high precision. (orig.)

International Nuclear Information System (INIS)

Four materials of the types Inconel 706 (two heat treatment states), Inconel 617, and Waspaloy were tested as shaft materials for 700 to 720 C steam turbines. At an extrapolation time ratio of 10, Waspaloy was expected to have the highest creep strength (about 270 MPa at 700 C), with values of about 140 MPa at 700 C for Inconel 617. A preliminary evaluation of the 700 C creep rupture tests showed the highest creep rupture resistance for Inconel 617, followed by Waspaloy and Inconel 706.

Energy Technology Data Exchange (ETDEWEB)

We propose a dissolution-passivation model to account for the electrochemical behavior of Alloy 800 and 316L stainless steel under steam generators operating conditions. This model is similar to the one defined for nickel, considering the known importance of this element on the studied alloys. The comparison of the rates of the elementary steps points out the favorable influence of dissolved oxygen and phosphate ions on the dissolution of Alloy 800, even in the presence of chloride ions. The sensitivity of 316L SS is greater, especially because of the lowest stability of oxide-like intermediate.

Science.gov (United States)

The results of the second phase of the program of developing low cost contacts to silicon solar cells using copper are presented. Phase 1 yielded the development of a plated Pd-Cr-Cu contact system. This process produced cells with shunting problems when they were heated to 400 C for 5 minutes. Means of stopping the identified copper diffusion which caused the shunting were investigated. A contact heat treatment study was conducted with Pd-Ag, Ci-Ag, Pd-Cu, Cu-Cr, and Ci-Ni-Cu. Nickel is shown to be an effective diffusion barrier to copper.

Energy Technology Data Exchange (ETDEWEB)

The theoretical principles underlying the formation of oxide and, in particular, anodic oxide coatings on metals produced by chemical oxidation, anodizing in solutions, and anodizing in cold plasmas are reviewed. The mechanisms and conditions of anodic oxidation are described, and the structure of anodic oxide coatings on aluminum, magnesium, beryllium, zinc, cadmium, iron, cobalt, nickel, titanium, zirconium, tantalum, and chromium alloys is examined. Attention is also given to various applictins of anodized coatings. 54 references.

Energy Technology Data Exchange (ETDEWEB)

The time-temperature-precipitation diagrams and the resulting time-temperature-sensitization diagrams have been established and are presented for today's current nickel-chromium-molybdenum alloys C-4, C-276, 22 and the recently developed alloy 59. Compared to those materials alloy 625 behaves differently due to its high niobium content. In addition, also the precipitation and sensitization of alloy G-3 has been established. Under the materials considered alloy C-276 has the strongest tendency to precipitate the intermetallics Mu and P together with the carbide M{sub 6}C at intermediate temperatures, followed by the alloys 22 and 59. The tendency to sensitization in the sense of the 50{mu}m (2 mils) intercrystalline penetration criterion when exposed to the ASTM G-28, method A test solution is greatest with alloy C-276, and decreases over the alloys 22, 59 and G-3 to alloy 625. Sensitization is caused by precipitation of the intermetallics {mu} and P and ...

International Nuclear Information System (INIS)

Suspension direct current plasma spraying allows achieving finely structured coatings whose thickness is between few tens and few hundreds of micrometres. Drops (200-300 ?m in diameter) or liquid jets are mechanically injected in the plasma jet. With radial injection they are rapidly (a few ?s) fragmented into droplets (a few ?m in diameter). The latter are vaporized (in a few ?s) and the solid particles contained in suspension droplets are accelerated and melted by the plasma jet. As in conventional plasma spraying (CPS), much smaller splats (with diameters between 0.2 and 3 ?m and thicknesses between 30 and 200 nm) are arranged in layers up to form the coating. The low inertia of particles requires spray distances between 40 and 60 mm which induces plasma heat fluxes up to 22 MW m-2 participating in coating densification. Even more than in CPS, the plasma jet fluctuations, particularly for plasmas containing di-atomic gases, perturb drops penetration and fragmentation. It has been ...

Energy Technology Data Exchange (ETDEWEB)

The dissolution of NiO cathodes during cell operation is a limiting factor to the successful commercialization of molten carbonate fuel cells (MCFCs). Lithium cobalt oxide coating onto the porous nickel electrode has been adopted to modify the conventional MCFC cathode which is believed to increase the stability of the cathodes in the carbonate melt. The material used for surface modification should possess thermodynamic stability in the molten carbonate and also should be electro catalytically active for MCFC reactions. Two approaches have been adopted to get a stable cathode material. First approach is the use of LiNi{sub 0.8}Co{sub 0.2}O{sub 2}, a commercially available lithium battery cathode material and the second is the use of tape cast electrodes prepared from cobalt coated nickel powders. The morphology and the structure of LiNi{sub 0.8}Co{sub 0.2}O{sub 2} and tape cast Co coated nickel powder electrodes were ...

Energy Technology Data Exchange (ETDEWEB)

Development of electronic devices with better performance and smaller size requires the passive components to be embedded within a printed wire board (PWB). The 'film-on-foil' approach is the most viable method for embedding these components within a PWB. We have deposited high-permittivity ferroelectric lead lanthanum zirconate titanate (Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub x}, PLZT 8/52/48) films on base metal foils by chemical solution deposition. These prefabricated capacitor sheets can be embedded into PWBs for power electronic applications. To eliminate the parasitic effect caused by the formation of a low-permittivity interfacial oxide, a conductive buffer layer of lanthanum nickel oxide (LNO) was applied by chemical solution deposition on nickel foil before the deposition of PLZT. With a {approx} 0.7-{micro}m-thick ferroelectric PLZT film grown on LNO-buffered nickel foil, we ...

Energy Technology Data Exchange (ETDEWEB)

Subcritical experiments using californium source-driven noise analysis (CSDNA) and Feynman variance-to-mean methods were performed with an alpha-phase plutonium sphere reflected by nickel shells, up to a maximum thickness of 7.62 cm. Both methods provide means of determining the subcritical multiplication of a system containing nuclear material. A benchmark analysis of the experiments was performed for inclusion in the 2010 edition of the International Handbook of Evaluated Criticality Safety Benchmark Experiments. Benchmark models have been developed that represent these subcritical experiments. An analysis of the computed eigenvalues and the uncertainty in the experiment and methods was performed. The eigenvalues computed using the CSDNA method were very close to those calculated using MCNP5; however, computed eigenvalues are used in the analysis of the CSDNA method. Independent calculations using KENO-VI provided similar eigenvalues to those determined using the ...

International Nuclear Information System (INIS)

Coal is the most abundant available fossil fuel in Australia and provides a substantial part of energy needs. It is used for power generation, to supply energy to industry as well as for domestic requirements. Analysis of trace elements (the elements present in coal in ppm/ppb level) during combustion of coal in very important. Trace elements, like heavy metals such as arsenic, selenium, and chromium etc. are hazardous to the environment and some of them have carcinogenic potency. In the near future more stringent limits may be proposed for such elements generated from combustion process, such as coal combustion in power plants. Hence analysis and assessment of the emissions of these elements is essential at this stage. The first step towards reducing any impacts of trace elements is to have accurate quantitative analysis. Analysis of coal, bottom ash and fly ash collected from five different power stations across Australia was carried out to study the quantity and ...

Energy Technology Data Exchange (ETDEWEB)

The first study in this dissertation describes the development of a suppressed ion chromatographic (SIC) technique for the direct, simultaneous determination of the As and Se oxyanions in soil solution. Baseline resolution of 1 mg L[sup [minus]1] each of arsenite, arsenate, selenite, and selenate was achieved in the presence of 50 mg L[sup [minus]1] each of F, Cl, NO[sub 3]-N, SO[sub 4]-S, and PO[sub 4]-P. Detection limits ranged from 0.026 mg L[sup [minus]1] for selenite to 0.120 mg L[sup [minus]1] for arsenate. The accuracy of the SIC technique was verified by comparison to spectroscopic methods. The second study investigated the suitability of linear-plateau regression analysis for statistical evaluation of As adsorption data. The time required to reach the adsorption plateau depended on soil characteristics and As species. Identification of the adsorption plateau by the linear-plateau model allowed comparison of adsorption rates and maxima through analysis of covariance and least ...

International Nuclear Information System (INIS)

The mechanism of lead transport is presented, and especially the particular similarities or dissimilarities between lead and calcium in this process. The absorption of these metals was determined cockerels, raised on a commercial diet or on a specified diet, using in vivo ligated loop procedure. The dose administered into the loop contained 0.5 #mu#Ci "2"0"3Pb (and/or 0.1 #mu#Ci "4"7Ca), and 0.01 mM lead acetate (and/or mM CaCl_2) in 0.5 ml 0.15 M NaCl,pH 6.5. It was shown that lead is rapidly taken up by the mucosal tissue, and slowly transferred into the body, whereas less calcium is retained by the tissue and the transfer of calcium is many times as effective as that for lead. They appear to respond in a similar manner to a low calcium intake and vitamin D treatment. Increasing luminal stable lead concentration significantly reduced the percentage of radiolead significantly reduced the percentage of radiolead absorbed, but did not affect the absorption of calcium. Also, vitamin D ...

Energy Technology Data Exchange (ETDEWEB)

Mercury is an element which, with its compounds, is hazardous and is found in hazardous wastes. In Order to develop suitable diagnostic and therapeutic agents for mercury exposure, we have sought alternative test systems. We have used the chelating agent 2,3-dimercaptopropane-1-sulfonate (DMPS, DIMAVAL{reg_sign}) for estimating the body burden of mercury in normal humans and in dental personnel in a developing country, and for detoxifying humans with mercurous chloride exposure. Use of the DMPS-mercury challenge test has shown that two-thirds of the mercury excreted in the urine of volunteers with dental amalgams appears to be derived from the mercury vapor released from their amalgams. The DMPS challenge test (300 mg, by mouth, after an 11 hr fast) was useful for monitoring dental personnel for mercury vapor exposure. The DMPS challenge test was given to 11 factory workers who make a skin lotion that contains mercurous chloride, 8 users of the skin lotion, and 9 controls. The ...

Energy Technology Data Exchange (ETDEWEB)

TRITEX was a pumped loop with Pb-15.8Li, fabricated from steel 1.4922. In contact with the molten eutectic were also molybdenum, vanadium and armco-iron. The loop was originally designed to investigate tritium extraction using solid getter metals. Over the years the goal changed to the study of metals, corrosion products and purification of the eutectic mixture. Therefore many modifications were done. The first part of this report describes TRITEX. All parts were enclosed in thermoboxes for a homogeneous temperature. One test section was in an argon glove box and could be opened during operation. Other special equipment`s were: permeation membranes and liquid-metal-covergas-interfaces to study the transport of H{sub 2}, D{sub 2} and {sup 3}H, different purification devices, a quartz observation window to see the liquid metal surface, 4 different kinds of flow measurements, level indicators, freeze valves. The second part describes loop operation. Between 1989 and ...

Science.gov (United States)

We have grown crack-free antiferroelectric (AFE) Pb{sub 0.92}La{sub 0.08}Zr{sub 0.95}Ti{sub 0.05}O{sub 3} (PLZT) films on nickel foils by chemical solution deposition. To eliminate the parasitic effect caused by the formation of a low-permittivity interfacial oxide, we applied a conductive buffer layer of lanthanum nickel oxide (LNO) on the nickel foil by chemical solution deposition prior to the PLZT deposition. Use of the LNO buffer allowed high-quality film-on-foil capacitors to be prepared at high temperatures in air. With the AFE PLZT deposited on LNO-buffered Ni foils, we observed field-induced phase transformations of AFE to ferroelectric (FE). The AFE-to-FE phase transition field, E{sub AF} = 260 kV cm{sup -1}, and the reverse phase transition field, E{sub FA} = 220 kV cm{sup -1}, were measured at room temperature on a {approx}1.15 {micro}m thick PLZT film grown on LNO-buffered Ni foils. The relative permittivities ...

International Nuclear Information System (INIS)

A new high strength titanium alloy has been developed primarily intended for fastener applications. While Ti-6Al-4V is used extensively as a fastener alloy in the aerospace industry, its shear strength allowable is limited to 655 MPa (95 ksi). For higher shear strength requirements, various steels or nickel-based alloys are used (up to 860 MPa (125 ksi)), but with the attendant density penalty. This new alloy is intended to provide the 860 MPa shear strength at roughly a 40% weight savings. After screening various alloy systems, the optimum chemistry has been selected as follows: Ti-6.0V-6.2Mo-5.7Fe-3Al. In light of its 125 ksi shear strength goal, the alloy has been designated TIMETAL reg-sign 125.

International Nuclear Information System (INIS)

The introduction of oxygen in the vicinity of a metallic target surface, bombarded with positive argon ions of twenty kiloelectron-volts, increases the number of sputtered atoms in the excited state. This phenomenon of exaltation, very sensitive in the case of nickel and aluminium, is much less marked in the case of molybdenum. Moreover, the emission of excited particles coming from the beam's ions is not modified. A quantum-mechanical model of a kinetic emission process, which permits the interpretation of the clean metallic target's emission phenomena, seems insufficient to explain all of the results obtained in the presence of oxygen. In this last case one can therfore use a thermodynamic model in which excited metallic particles can be formed directly by chemical surface reactions of neutralization or reduction. (orig.).

British Library Electronic Table of Contents (United Kingdom)

Aerial deposition of Ni from a refinery in Port Colborne, Ontario, Canada has resulted in the enrichment of 29km2 of land with Ni concentrations exceeding the Canadian Ministry of the Environment's remedial action level of 200mgkg-1. Several studies on these soils have shown that making the soils calcareous was effective at reducing chemically extractable Ni, as well as alleviating Ni phytotoxicity symptoms in vegetable crops grown in the vicinity of the refinery. Conversely, dolomitic limestone additions resulted in increased uptake of Ni in the Ni hyperaccumulator Alyssum murale `Kotodesh', a plant whose use was proposed as a remediation strategy for this area. In this paper we use multiple techniques to directly assess the role soil type and lime treatments play in altering the speciati...

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on stainless steels in a borate buffer solution (pH 9.2) have been investigated by capacitance measurements and photoelectrochemistry. The study was carried out on films formed on AISI type 304 and 316 stainless steels and high purity alloys with differing chromium, nickel, and molybdenum contents. Complementary research by Auger analysis shows that the passive films are composed essentially of an inner chromium region in contact with the metallic substrate and an outer iron oxide region developed at the film/electrolyte interface. The semiconducting properties of the passive films are determined by those of the constituent chromium and iron oxides which are of p-type and n-type, respectively. Thus the influence of the alloying elements on the semiconducting properties of the passive films is explained by changes in the electronic structure of each of these two oxide regions.

Energy Technology Data Exchange (ETDEWEB)

The chronology of installing solar power in a rural area of Ontario is described. The installation took all of seven years, and was characterized by a lot of joy, but also a lot of heartache and hardship, all of which are chronicled in this article. The project started with four solar modules generating 300 watts, nickel cadmium batteries of 225 Ah, an inverter of 600 watt, and a three-cylinder 6.5 Kw water-cooled propane generator. Today, nearly seven years later, the installation consists of 18 solar modules supplying 1350 watts of power, lead-acid batteries of 2770 Ah, a 2500 watt inverter, a one cylinder, 5.5 kw propane-gasoline generator, a heated, underground generator house, complete with an amp-hour meter and MPPT charge controller.

International Nuclear Information System (INIS)

Methods of automated control of 18-10-type steel inclination to IGC are developed and a corresponding automated testing complex (ATS) is created. 08Kh18N10T steel samples had two variants of thermal treatment: 1) 1200 deg (5 h), 600 deg (50 h); 2) 1200 deg (5 h). Methods of non-destructive automated control of 18-10-type steel inclination to IGC are developed on the basis of potentiodynamic reactivation (PR) principle. Automated testing complex is developed, which has undergone experimental running and demonstrated a high confidence of results, reliability and easy operation.

Energy Technology Data Exchange (ETDEWEB)

We have measured production cross-sections of the new neutron-rich isotopes {sup 58}Ti, {sup 61}V, {sup 63}Cr, {sup 66}Mn, {sup 69}Fe, {sup 71}Co and neighbouring isotopes that have been identified as projectile fragments from reactions between a 500 MeV/u {sup 86}Kr beam and a beryllium target. The isotope identification was performed with the zero-degree magnetic spectrometer FRS at GSI, using in addition time-of-flight and energy-loss mesurements. The experimental production cross-sections for the new nuclides and neighbouring isotopes are compared with an empirical parameterization. The resulting prospects for reaching even more neutron-rich isotopes, such as the doubly-magic nuclide {sup 78}Ni, are discussed. (orig.).

International Nuclear Information System (INIS)

We have measured production cross-sections of the new neutron-rich isotopes "5"8Ti, "6"1V, "6"3Cr, "6"6Mn, "6"9Fe, "7"1Co and neighbouring isotopes that have been identified as projectile fragments from reactions between a 500 MeV/u "8"6Kr beam and a beryllium target. The isotope identification was performed with the zero-degree magnetic spectrometer FRS at GSI, using in addition time-of-flight and energy-loss measurements. The experimental production cross-sections for the new nuclides and neighbouring isotopes are compared with an empirical parametrization. The resulting prospects for reaching even more neutronrich isotopes, such as the doubly-magic nuclide "7"8Ni, are discussed. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The present volume on modeling of batteries and fuel cells discusses the significance of the effectiveness factor for flooded porous electrodes, active pore distribution spectroscopy for characterizing porous battery electrodes, the agglomerate model for porous electrodes, and dynamic-performance measurements of battery cells for electric vehicles and other applications. Attention is given to mathematical modeling of a primary zinc/air battery, mathematical modeling of Grace Li-TiS2 cells, modeling of electrocrystallization processes in battery systems, and rotating disk electrode studies in molten Li/K carbonate eutectic. Topics addressed include the variability of nickel oxide cathode dissolution in molten carbonate fuel cells, water transport properties of fuel cell ionomers, modeling water content effects in polymer electrolyte fuel cells, and computer algebra applied in electrochemistry and fuel cell modeling.

Science.gov (United States)

A proposed metallization system for large area silicon solar cells with shallow junctions is outlined, and its desirable features are discussed. A baseline process sequence for the nickel palladium metallization system (NPMS) is delineated. This baseline process sequence is serving as the starting point from which process variations are being performed. The eventual goal is optimization of the NPMS process and determination of the control ranges for NPMS process variables. Initial studies of palladium displacement and electroless chemical plating solutions used in the baseline NPMS have begun and progress is reported. In support of this work, an annotated bibliography (45 citations) dealing primarily with palladium plating and palladium-silicon contact formation has been prepared (and will be subject to updating in the future reports).

Energy Technology Data Exchange (ETDEWEB)

Plutonium oxide fuel pellets for powering radioisotopic thermoelectric generators for NASA space vehicles are encapsulated in iridium which has been grain-boundary-stabilized with thorium and aluminum. After aging for 6 months at 1310/sup 0/C under vacuum, enhanced grain growth is observed in the near-surface grains of the iridium next to the PuO/sub 2/. Examination of the grain boundaries by AES and SIMS shows a depletion of thorium and aluminum. Iron, chromium, and nickel from the fuel were found to diffuse into the iridium along the grain boundaries. Enhanced grain growth appears to result from thorium depletion in the grain boundaries of the near-surface grains next to the fuel. However, in one instance grain growth was slowed by the formation of thorium oxide by oxygen diffusing up the grain boundaries.

International Nuclear Information System (INIS)

By using megaelectronvolt "4He ion backscattering techniques and transmission electron microscopy, the authors have investigated the interactions of ion beams with thin film structures in a number of silicide-forming systems. The mixed layer was found to be an equilibrium compound for near-noble metals and an amorphous phase for refractory metals. Differences in behavior have also been observed in near-noble metal systems. For palladium, the Pd_2Si phase grew with ion dose and remained crystalline up to high dose. For nickel, the compound Ni_2Si was formed initially and became amorphous on prolonged irradiation. All the results indicate the significance of atomic mobility at target temperatures in determining the phase formation and in explaining the sensitivity of the silicides to ion bombardment. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on Alloy UNS N06690 were investigated in simulated crevice chemistries. It was found the role of lead in corrosion processes is strongly dependent on the pH value of the testing solutions. At pH 1.5 the effect of lead is narrowly noticeable; while at pH 12.7, lead has a significant influence on the electrochemical performance of alloy UNS N06690. The lead alters the surface morphologies at both pH and account for higher hydroxide content in the surface film at pH 12.7. The lead incorporation hinders the formation of spinel oxides during the passivation in alkaline solution. Nanoindentation tests indicate a significant lead-induced degradation in the mechanical properties of passive films. The passivation degradation is attributed to detrimental effects of lead via interrupting the dehydration process and hindering the formation of protective layers on the alloy surface.

International Nuclear Information System (INIS)

Passive films formed on Alloy 690 in different pH solutions at high temperatures were studied by potentiodynamic polarization, Auger electron spectroscopy, thermodynamic diagrams and the Mott-Schottky relation. The chemical compositions and electronic structures of the passive films were found to be strongly pH-dependent. In alkaline solutions, a secondary passivation was clearly observed on potentiodynamic polarization curves. The passive films were a mixture of Cr2O3 and FeCr2O4 below the flat band potential of nickel oxide and were NiFe2O4 above this potential. Electronic structure models, describing the electrochemical properties of the passive films, are proposed and discussed.

International Nuclear Information System (INIS)

Resistance of Alloy 800 as a PWR S/G tube material to IGC/IGSCC and Ni, Co release into water was evaluated as compared with Alloys 600 and 690. The study to improve the resistance to IGSCC and general corrosion was also made, including the effects of shot-peening on the distribution of the residual stress of the U-bent tubes and the susceptibility to SCC, the stabilizing elements on IGC/IGSCC, and prior oxidation on general corrosion. From the results, shot-peened Alloy 800 was estimated to be the most reliable S/G tube material among the high nickel alloys tested. In addition, the Alloy 800 tube would obtain further reliability in IGSCC and general corrosion resistance by the combined addition of Ti, and Nb, and the prior oxidation of the inner tube surface, respectively.

British Library Electronic Table of Contents (United Kingdom)

The formation of nanoparticles during the radiation-induced chemical reduction of silver ions, copper ions, and nickel ions in films based on poly(acrylic acid)-poly(ethylenimine) complexes are studied via electron microscopy. This approach allows preparation of composites containing nanoparticles that are randomly distributed in the polymer matrix and materials with a regular spatial distribution of nanoparticles across the film thickness and in subsurface layers. The structure of metal-polymer hybrid materials is dependent on the irradiation conditions, the type of reduced metal ions, and their initial content in polymer matrices. The ratio between the rate of nucleation and the rate of growth of nanoparticles in the matrices of interpolyelectrolyte complexes depends on the intensity of ...

International Nuclear Information System (INIS)

Purpose: To dissolve iron and nickel as well as chromium simultaneously at one step for cruds partially containing chromium, and obtain high decontaminating factor (decontamination factor). Method: Radioactive cruds formed as corrosion products in nuclear reactor primary coolant circuits are subjected to dissolving treatment by using a decontaminating agent composed of cerium sulfate type solution as the dissolving solution. When the treatment is substantially completed, a reducing agent is added to reduce the residual 4-valent cerium into 3-valent cerium. Those having potential lower than the redox potential of cerium are used as the reducing agent so that cerium is not deposited. This can provide high decontaminating factor while preventing the deposition of cerium. (Takahashi, M.).

British Library Electronic Table of Contents (United Kingdom)

The electroless nickel plating/poly(dl-lactide-co-glycolide) composite coating (EN-plating/PLGA composite coating) was fabricated on the surface of the micro-arc oxidation (MAO) film of the magnesium alloy AZ81 to double control the corrosion and drug release in the hanks' solution. The EN-plating was fabricated on the MAO coating to improve the corrosion resistance by overlaying most pores and micro-cracks on the surface of the MAO film. Meanwhile, a double layered organic poly(dl-lactide-co-glycolide)/paclitaxel (PLGA/PTX) drug releasing coating with a top layered PLGA drug controlled releasing coating on EN plating was prepared to control the drug release rate by adjusting the different lactide: glycolide (LA:GA) ratio of PLGA. Scanning electron microscopy (SEM) and the X-ray powder dif...

British Library Electronic Table of Contents (United Kingdom)

The Jaduguda U (?Cu?Fe) deposit in the Singhbhum shear zone has been the most productive uranium deposit in India. Pyrite occurs as disseminated grains or in sulphide stringers and veins in the ore zone. Veins, both concordant and discordant to the pervasive foliation, are mineralogically either simple comprising pyrite ? chalcopyrite or complex comprising pyrite + chalcopyrite + pentlandite + millerite. Nickel-sulphide minerals, though fairly common in concordant veins, are very rare in the discordant veins. Pyrite in Ni-sulphide association is commonly replaced by pentlandite at the grain boundary or along micro-cracks. Based on concentrations of Co and Ni, pyrite is classified as: type-A ? high Co (up to 30800?ppm), no/low Ni; type-B ? moderate Co (up to 16500?ppm) and moderate to high ...

Energy Technology Data Exchange (ETDEWEB)

The prototype Bragg Curve Counter (BCC) has been tested by {alpha}-source ({sup 241}Am) with a continuous gas flow system (P-10: 90% Ar+10% CH{sub 4}, at 300Torr). Two types of the Frisch grid were prepared for the BCC. One was made of expanded metal meshes, which consist of 175 meshes/inch{sup 2} with a 100{mu}m{sup t} nickel sheet. The other was made of a 1mm pitch wire with {phi} 50 {mu}m of the tungsten. The shape of Bragg peak signal was compared each other. It was found that the energy spectrum obtained by the wire grid is a little sharper than that obtained by the meshes grid. However the meshes grid is superior than the wire grid so far as handling and durability are concerned. (author).

International Nuclear Information System (INIS)

Alloy 800 has been used by Siemens since 1968 and is now used by KWU for U-tubed steam generators in PWR's. The particular grade of alloy 800 that is used is within the ASTM-Specification B 163, but there have been modifications in composition to improve the corrosion resistance. First the permitted upper limit of carbon was reduced to 0.04% and was then further reduced to 0.03% and a stabilisation ratio of Ti : C >= 12 and Ti : C + N >= 8 was specified. The minimum permitted chromium and nickel levels were increased to 20% and 32% respectively. The maximum permitted levels of other elements or impurities were reduced. At the final fabrication stage peening with glass beads on the outer surface was specified to introduce a compressive stress to depth greater than that allowed for production flaws. An account is given of the behaviour of the alloy in service in four power plants already in operation, and future developments are discussed. (author).

Energy Technology Data Exchange (ETDEWEB)

Red mud has been activated by dissolution in hydrochloric acid and reprecipitation with ammonia. The activated material has been evaluated as a catalyst for the hydrogenation of naphthalene, phenanthrene and pyrene and in the hydroliquefaction of both a high and low rank coal utilizing solvents of high and low hydrogen donating ability. Activation led to a substantial increase in the ability to hydrogenate the model compounds and a significant increase in oil yield was obtained in the hydroliquefaction of a low rank coal in the presence of a poor donor solvent. However, activation did not lead to significant increases in overall yields of liquids in other cases and the activated red mud was significantly less active than a commercial nickel-molybdenum-sulphur catalyst. 27 refs., 1 fig., 5 tabs.

International Nuclear Information System (INIS)

Here we report normal-state conductance measurements of three different types of superconducting tunnel junctions that are being used or proposed for quantum computing applications: p-Al/a-AlO/p-Al, e-Re/e-AlO/p-Al, and e-V/e-MgO/p-V, where p stands for polycrystalline, e for epitaxial, and a for amorphous. All three junctions exhibited significant deviations from the parabolic behavior predicted by the WKB approximation models. In the p-Al/a-AlO/p-Al junction, we observed enhancement of tunneling conductances at voltages matching harmonics of Al-O stretching modes. On the other hand, such Al-O vibration modes were missing in the epitaxial e-Re/e-AlO/p-Al junction. This suggests that absence or existence of the Al-O stretching mode might be related to the crystallinity of the AlO tunnel barrier and the interface between the electrode and the barrier. In the e-V/e-MgO/p-V junction, which is one of the candidate systems for future superconducting qubits, we observed suppression of the ...

Energy Technology Data Exchange (ETDEWEB)

Flux-grown ScPO{sub 4} single crystals exhibit a number of luminescence bands in their x-ray-excited luminescence spectra - including sharp lines arising from rare-earth elements plus a number of broad bands at 5.6 cV, 4.4 eV, and 3 eV. The band at 5.6 eV was attributed to a self-trapped exciton (STE) [l], and it could be excited at 7 eV and higher energies. This luminescence is strongly polarized (P = 70 %) along the optical axes of the crystal and exhibits a kinetic decay time constant that varies from several ns at room temperature to {approximately}10 {micro}s at 60 K and up to {approximately}1 ms at 10 K. It is assumed that the STE is localized on the SC ions. The band at 3 eV can be excited in the range of the ScPO{sub 4} crystal transparency (decay time = 3 to 4 {micro}s.) This band is attributed to a lead impurity that creates different luminescence centers. At high temperatures, the band at 4.4 eV is dominant in the x-ray-excited TSL and afterglow spectra. Its intensity ...

Energy Technology Data Exchange (ETDEWEB)

The 1977 version of the Simpson-Puls-Dutton model appears to be the most amenable with respect to utilizing known or readily estimated quantities. The Pardee-Paton model requires extensive calculations involving estimated quantities. Recent observations by Koike and Suzuki on vanadium support the general assumption that crack growth in hydride forming metals is determined by the rate of hydride formation, and their hydrogen atmosphere-displacive transformation model is of potential interest in explaining hydrogen embrittlement in ferrous alloys as well as hydride formers. The discontinuous nature of cracking due to hydrogen embrittlement appears to depend very strongly on localized stress intensities, thereby pointing to the role of microstructure in influencing crack initiation, fracture mode and crack path. The initiation of hydrogen induced failures over relatively short periods of time can be characterized with fair reliability using measurements of the ...

International Nuclear Information System (INIS)

The hardening and embrittlement of reactor pressure vessel (RPV) steels is of great concern in the actual nuclear power plant life assessment. This embrittlement is caused by irradiation-induced damage, like vacancies, interstitials, solutes and their clusters. The current procedure to estimate material properties for the irradiated pressure vessels is based on Charpy-V tests of identical material located at the inner shell of the reactor. But the reason for the embrittlement of the materials is not yet totally known. The real nature of the irradiation damage should thus be examined as well as its evolution in time. Fe-Cu binary alloys are often used to mimic the behaviour of such steels. Their study allows. Identifying some of the defects responsible of the hardening, especially when compared to pure iron or C-micro-alloyed iron. More recently the influence of manganese and nickel in low-Cu RPV steels has become a significant topic. Thus in contrast with the ...

Energy Technology Data Exchange (ETDEWEB)

The permeation of hydrogen through steam generator tubes at high temperatures ({approx} 300 degrees C) has been studied using an electrochemical technique. With this technique, hydrogen is generated on one side of the tube and monitored on the other side. The time for the hydrogen to reach the other side is used to determine the diffusion coefficient of hydrogen in the tube. Boundary conditions at the entry and exit sides have been investigated separately. Preliminary studies were performed on Stainless Steel 316 and Nickel Alloy 800 to better understand the influence of the solution chemistry on the electrochemical evolution of hydrogen. The surface phenomena effect and the trapping effect are discussed to account for differences observed in the permeation response. The hydrogen permeation through oxides at the exit side has been studied. Two nickel alloys (Alloy 800 and Alloy 600), materials widely used for steam generator tubes, have been ...

Energy Technology Data Exchange (ETDEWEB)

Ni catalysts supported on {gamma}-Al{sub 2}O{sub 3}, CeO{sub 2} and CeO{sub 2}-Al{sub 2}O{sub 3} systems were tested for catalytic CO{sub 2} reforming of methane into synthesis gas. Ni/CeO{sub 2}-Al{sub 2}O{sub 3} catalysts showed much better catalytic performance than either CeO{sub 2}- or {gamma}-Al{sub 2}O{sub 3}-supported Ni catalysts. CeO{sub 2} as a support for Ni catalysts produced a strong metal-support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO{sub 2} had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/{gamma}-Al{sub 2}O{sub 3} catalysts for this reaction. A weight loading of 1-5wt% CeO{sub 2} was found to be the optimum. Ni catalysts with CeO{sub 2} promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on ...

Energy Technology Data Exchange (ETDEWEB)

Single and binary metal molybdates of the formula AMoO{sub 4}, where A=Ni, Co, Mg,Mn and/or Zn, were investigated for the oxydehydrogenation of propane to propylene, as well as some ternary molybdates of the formula NiO{sub 0.45}Co{sub 0.45}X{sub 0.066}MoO{sub 4} where X=P, Bi, Fe, Cr, V and Ce. All catalysts were supported on SiO{sub 2} with an active phase/support ratio of 80/20 (wt%). The reaction is catalytic and not a gas phase initiated reaction. It is first order in propane, consistent with the abstraction of the methylene hydrogen being the rate limiting step. Propane conversions and propylene yields vary greatly depending on the metal of the molybdate and surface area of the catalyst. Highest propylene yields (16% at 26.6% propane conversion) are obtained with NiMoO{sub 4}/SiO{sub 2}. Conversion and yield are significantly influenced by the molybdenum content of the compositions. The effect is biggest in the nickel molybdate system. Its optimum activity ...

Energy Technology Data Exchange (ETDEWEB)

We have grown ferroelectric Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} (PLZT) films on platinized silicon and LaNiO{sub 3}-buffered nickel substrates by chemical solution deposition using a sol-gel process based on acetic acid chemistry. The following measurements were obtained under zero-bias field: relative permittivity of {approx}960 and dielectric loss of {approx}0.04 on the PLZT film grown on Pt/Si substrates, and relative permittivity of {approx}820 and dielectric loss of {approx}0.06 on the PLZT film grown on LNO-buffered Ni substrates. In addition, a relative permittivity of 125 and dielectric loss of 0.02 were measured at room temperature under a high bias field of 1 x 10{sup 6} V/cm on PLZT deposited on LNO-buffered nickel substrate. Furthermore, a steady-state leakage current density of {approx}8.1 x 10{sup -9} A/cm{sup 2} and mean breakdown field strength of 1.7 x 10{sup 6} V/cm were measured at room temperature. ...

International Nuclear Information System (INIS)

Surface analytical studies of high nitrogen austenitic stainless steels exposed to deaerated 0.1M HCl have revealed that nitrogen alloying additions influence the composition of salt layers and the passive film/alloy interface. In this study the authors employ electrochemical techniques and variable angle X-ray Photoelectron Spectroscopy (XPS) to examine the passive films formed on a series of austenitic stainless steels, Fe18Cr8Ni, Fe18Cr8Ni0.2N, Fe20Cr20Ni, Fe20Cr20Ni6Mo and Fe20Cr20Ni6Mo0.2N, in acidic chloride aqueous solution. In addition, several other model alloys, Fe19Cr, Fe19Cr9Ni, Fe19Cr2.5Mo, and Fe19Cr9Ni2.5Mo, were examined before and after electrochemical surface nitriding, a technique proven to have an effect analogous to N alloying. It was shown that nitrogen, nickel and molybdenum additions independently and in certain combinations stimulate selective dissolution of iron, resulting in a significant enrichment of chromium beneath the passive film. ...

International Nuclear Information System (INIS)

Three ternary austenitic alloys (Fe-15Cr-25Ni, Fe-15Cr-25Ni-0.04P, Fe-15Cr-45Ni in both annealed and cold worked conditions) were irradiated at 465 C to 0.15, 0.28, and 0.42 dpa at above core position in the Fast Flux Test Facility utilizing the Materials Open Test Assembly to study the separate and synergistic effects of He/dpa ratio, phosphorus addition, nickel content and cold work level on microstructural evolution and hardening. The helium/dpa ratio was varied by isotopic doping with "5"9Ni to enhance the production rate of helium. The helium production rate was evaluated to be 62 appm He/dpa in the "5"9Ni-doped specimens and 0.26 appm He/dpa in the undoped specimens. Transmission electron microscopic examinations revealed that alloy composition affected significantly the evolution of microstructure during irradiation. Phosphorus addition prevented the formation of Frank loops through the precipitation of phosphide. Nickel content ...

Energy Technology Data Exchange (ETDEWEB)

The rare-earth based nickelates RNiO{sub 3} (R = Pr, Nd, Sm, Eu, and Pr{sub 1-x}La{sub x}, 0{<=}x{<=}0.7) were studied by inelastic neutron scattering. Energy splittings due to the crystalline-electric-field (CEF) interaction at the R{sup 3+} site within the electronic ground-state J multiplet (for R = Pr, Nd, and Pr{sub 1-x}La{sub x}) as well as within the two lowest-lying J multiplets (for R = Sm and Eu) were directly observed, and the corresponding CEF energy-level schemes were reconstructed. The latter were rationalized in terms of CEF parameters, which vary smoothly over the rare-earth series and give magnetic properties associated with the R sublattice in agreement with results from neutron powder diffraction experiments. Across the metal-insulator transition, a continuous change in the electronic part of the CEF parameters is observed. However, an attempt to quantify a charge transfer from the observed variation of the CEF parameters in an ...