Energy Technology Data Exchange (ETDEWEB)

In this work the development of a third order scheme of finite differences centered in mesh is presented and it is applied in the numerical solution of those diffusion equations in multi groups in stationary state and X Y geometry. Originally this scheme was developed by Hennart and del Valle for the monoenergetic diffusion equation with a well-known source and they show that the one scheme is of third order when comparing the numerical solution with the analytical solution of a model problem using several mesh refinements and boundary conditions. The scheme by them developed it also introduces the application of numeric quadratures to evaluate the rigidity matrices and of mass that its appear when making use of the finite elements method of Galerkin. One of the used quadratures is the open quadrature of 4 points, no-standard, of Newton-Cotes to evaluate in approximate form the elements of the rigidity matrices. The other quadrature is that of 3 points of Radau that it is used to ...

Science.gov (United States)

... ADD137758. Title : The Oxidation Behavior of CoCrAlY, CoCrAl and Yttrium-Implanted CoCrAl Alloys Compared and Contrasted,. ...

International Nuclear Information System (INIS)

Short communication.

Science.gov (United States)

... Dusi 1957; Feldhamer 1985; Feldhamer et al. 1987; Hanebrink et al. 1979; Lavers 1990; Miller 1994; Paige et al. 1979; Parmalee 1954; Smith and Hanebrink 1982; Steward et al. 1988; Tedards 1963; Trost ... ...

Energy Technology Data Exchange (ETDEWEB)

We present a study of the crystal field in PrNiAl, NdNiAl, ErNiAl and ErCuAl intermetallic compounds based on inelastic neutron spectroscopy. These compounds crystallize in the ZrNiAl-type hexagonal structure with an orthorhombic symmetry on rare-earth sites. The results are compared with the specific-heat data, and the lower parts of the crystal-field energy-level schemes are determined. (orig.)

International Nuclear Information System (INIS)

"2"7Al and "2"9Si solid-state NMR spectra and X-ray diffraction (XRD) patterns were obtained for #alpha#-SiAlON powders prepared by combustion synthesis, according to which the phase transformation and structure evolution of #alpha#-SiAlON were studied. It was found that in #alpha#-SiAlON "2"9Si chemical shift values (-48 < #delta# _S_i < -47) were close to those in #beta#-Si_3N_4 and #alpha#-Si_3N_4, indicating that Si atoms kept SiN_4 coordination to a large extent in #alpha#-SiAlON despite the presence of O atoms. Dissimilarly, "2"7Al chemical shift values in #alpha#-SiAlON deviated clearly from that corresponding to AlN_4 coordination (#delta# _A_l #approx# 112) and occurred in a range from #delta# _A_l 95.5 to 99.9, which should be assigned to tetrahedral ...

International Nuclear Information System (INIS)

Synthesis of Eu-doped #beta#- and 15R-SiAlONs was studied by the ammonia nitridation of precursors derived from an #alpha#-Si_3N_4 fine powder dispersed in aluminum glycine gel with various Si/Al ratio and post-annealing in a nitrogen pressure furnace. The largest amount of #beta#-SiAlON was observed in the product at 1750 deg. C for Si/Al = 1/1 with small amounts of both #alpha#- and 15R-SiAlON impurities. The product showed two emissions at around 420 nm and 560 nm. The emission intensities decreased with increasing amount of #beta#-SiAlON. The former and latter emissions were assigned to Eu"2"+ in the 15R- and #alpha#-SiAlONs impurities. A mixture of Eu-doped 15R-SiAlON with #alpha#-Al_2O_3 impurity was obtained for Si/Al = 1/6, using AlN together with ...

International Nuclear Information System (INIS)

SiC-AlN and SiC-SiAlON refractory composites were obtained by means of nitridation of the mixtures of silicon carbide (SiC) powder with a broad granulometric distribution and powders of aluminium (Al) and aluminium-silicon (Al-Si) mixtures. The mixtures of the composition Al-25% Si, Al-50% Si and Al-75% Si were previously prepared by means of 'mechanical alloying' technique. Thermodynamic analysis was accomplished in order to evaluate the viability of SiC-SiAlON and SiC-AlN refractories production by the chosen processing method, and the results confirmed viability of such. Investigation of nitridation of Al and Al-Si powder compacts in order to obtain the AlN and #beta#-SiAlON matrix phases of the composite was ...

Energy Technology Data Exchange (ETDEWEB)

The morphology and size characteristics of the population of AlP particles produced by treatment of a pure aluminium melt with an Al-Fe-P inoculant addition have been determined. The particles are shown to be polyhedral like the primary silicon they nucleate in hypereutectic Al-Si alloy melts and to be prone to clustering at increased phosphorus addition levels. The number of AlP particles per unit area is shown to be comparable with the corresponding number density of polyhedral primary silicon in Al-20 wt.% Si treated in the same way under identical conditions which is consistent with earlier conclusions that AlP acts as a nucleation catalyst for primary silicon in hypereutectic Al-Si casting alloys. (orig.)

International Nuclear Information System (INIS)

Phase transformations from #alpha#- to #beta#-SiAlONs (i.e., from #alpha#' to #beta#') have been recently reported in a number of rare-earth SiAlON systems during postsintering heat treatment. In the present work, this transformation process in a Sm (#alpha# + #beta#)-SiAlON material is studied by using XRD, TEM, and EDS X-ray mapping techniques. It is observed that in addition to the formation of #beta#' and M' phases, the #alpha#'-to-#beta#' transformation is accompanied by a significant increase in the amount of an AlN-polytypoid phase. The results suggest that some #alpha#' phases are thermodynamically unstable at temperatures lower than the material sintering temperature and will decompose when conditions allow. For the composition studied in this work, the #alpha#-SiAlON decomposition can be described in general as #alpha#' #-># #beta#' + M' + AlN ...

Science.gov (United States)

Lea, MN Micro Albertville, AL Micro Albuquerque, NM Metro Alexander City, AL Micro Alexandria, LA Metro Alexandria, MN Micro Alice, TX Micro Allegan, MI Micro...

British Library Electronic Table of Contents (United Kingdom)

Abstract Electronic structures of two representative zigzag and armchair models of aluminum phosphide nanotube (AlPNT) were investigated by density functional theory calculations. The structures were optimized and the bond lengths, tip diameters, band gaps, and dipole moments were calculated. Moreover, the quadrupole coupling constants (CQ) were calculated for the Al-27 atoms of the optimized structures. The same values of AlP bond lengths were calculated for both models. The larger value of band gap of armchair model than the zigzag model indicated the stronger dielectric property for the former model. The values of CQ(27Al) were the largest for the Al atoms placed at the tips of both zigzag and armchair AlPNT than other Al atoms, which could reveal dominant role of the Al atoms placed at...

International Nuclear Information System (INIS)

Our work deals with accumulative roll bonding (ARB) of pure Mg sheet (0.9mm thickness) and of Al5052 sheet (0.5mm). A stacking of Al-Mg-Al was firstly rolled to 50% reduction at 400"0C and secondly ARB has been processed up to 3 cycles. In such multilayers as well as highly mixed composites of two-phased system texture development, phase reactions and strain accumulation are of basic interest, which needs a combination of different experimental methods for characterization. The present paper deals with the global texture evolution measured by thermal neutrons to average always over the whole sample thickness, SEM and optical microscopy indicates the macroscopic development of Mg and Al layers. The initial materials show typical and strong basal plane texture of hexagonal Mg (17.9mrd) and a recrystallization texture of cubic Al (8.5mrd). Co-deformation of Al/Mg/Al leads to strong ...

Energy Technology Data Exchange (ETDEWEB)

Possible explanations are given for the observed asymmetry of the analyzing power in several (rho,..pi../sup -/) reactions.

Energy Technology Data Exchange (ETDEWEB)

The microstructure of Al/{alpha}-Al{sub 2}0{sub 3} composites made by infiltrating Al into dense mullite preforms has been characterized using transmission electron microscopy. Observations revealed that the formation of the Al/Al{sub 2}0{sub 3} composites involves three stages. Initially, Al infiltrates into a dense mullite preform through grain boundary diffusion, and reacts with mullite at grain boundaries to form a partial reaction zone. Then, a complete reaction takes place in the reaction region between the partial reaction zone and the full reaction zone to convert the dense mullite preform to a composite of {alpha}-Al{sub 2}0{sub 3} (matrix) and an Al-Si phase (thin channels). Finally, the reduced Si from the reaction diffuses out of the Al/Al{sub 2}0{sub 3} composite through the metal channels, whereas Al from ...

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The effect of phosphorus on the corrosion resistance of Al-bronzes is studied in detail in this work. A literature review showed that there are a lot of things known about the microstructure and the mechanical properties of Al-bronzes. In spite of their corrosion resistance the corrosion properties and the structure of the protective oxide films of Al-bronzes were seldom a matter of interest. Systematic studies of the influence of different alloying elements on the oxide film and the corrosion properties are rare. Therefore, it is not possible to predict the corrosion resistance of Al-bronzes, made by alloying particular elements. The high corrosion resistance of the new alloy CuAl_2_0P_1 was the reason to investigate the influence of phosphorus on the corrosion properties of Al-bronzes in more detail. A systematic study of the microstructure and the corrosion ...

British Library Electronic Table of Contents (United Kingdom)

The tribological properties of gas pressure sintered SiAlON and its composite with 18wt% silicon carbide (SiC) against two different mating materials, i.e., alumina and SiAlON are evaluated. SiAlON and SiAlON-18%SiC composite ceramics were prepared by pressure less sintering and gas pressure sintering. Fretting wear tests were carried out under dry unlubricated ambient conditions (room temperature 23-25^oC; relative humidity 50-55%) with a load of 8N for 45,000 cycles. Friction and wear properties of SiAlON-SiC proved better than the monolithic SiAlON. The formation of silica roll like structure on the composite worn surface was observed.

Energy Technology Data Exchange (ETDEWEB)

The effect of Al and Be ions pre-implantation on microstructural change and, the formation and growth of He bubbles in SiC/SiC composite was investigated. Four kinds of ion implanted specimens were prepared with 100 appm Al, 1000 appm Al, 100 appm Be and 1000 appm Be implanted. No microstructural change was observed in the matrices and fibers of SiC/SiC composites implanted with Al or Be ions up to 1000 appm. The un-implanted and Al or Be pre-implanted SiC/SiC composites were simultaneously irradiated to 10 dpa using triple ion-beams (6.0-MeV Si{sup 2+}, 1.0-MeV He{sup +} and 340-keV H{sup +}) at 1000 deg. C. Helium bubbles were formed in every matrix and fiber irradiated by triple ion-beams. The size of He bubbles in the matrix was increased by implanting Al or Be ions and increased with increasing amount of implanted Al or Be ions. The ...

British Library Electronic Table of Contents (United Kingdom)

Methods of X-ray diffraction and transmission electron microscopy were used to study the microstructure of dispersion-strengthened Cu-Al2O3 nanocomposites obtained by the method of simultaneous deposition of Cu and Al2O3 from the vapor phase. The effect of the size of particles of the oxide (Al2O3) and of their content on the electrical resistance of the composite has been considered. The results obtained make it possible to suppose that the main structural factor that determines the electrical resistance of the composite are nanodispersed particles of Al2O3 with a size of less than 20 nm.

International Nuclear Information System (INIS)

The solubility limit of #alpha#'-SiAlON solid solutions on the Si_3N_4-YN:3AlN composition join in the system Si_3N_4-YN-AlN has been determined at 1800 degrees C. The end members of these solid solutions are Y_0_._4_3Si_1_0_._7Al_1_._3N_1_6 and Y_0_._8Si_9_._6Al_2_._4N_1_6. Unit-cell dimensions of the #alpha#'-SiAlON solid solutions in the system Si,Al,Y/N,O can be expressed as follows: a_0 (Angstrom) = 7.752 + 0.045m + 0.009n, c_0 (Angstrom) = 5.620 + 0.048m + 0.009n, where the #alpha#'-SiAlON solid solution has the formula Y_xSi_1_2_-_(_m _+ _n_)Al_m_+_nN_1_6_-_nO_n. The single-phase boundary of the solid solution #alpha#'-SiAlON on the composition triangle Si_3N_4-YN:3AlN-Al;N:Al_2O_3 is delineated. The present paper also reports the phase relationships ...

Energy Technology Data Exchange (ETDEWEB)

Micro-Vickers hardness measurement has been used to determine the composition of functionally graded materials (FGMs). Materials used in the present study are Al-SiC, Al-Shirasu and Al-Al{sub 3}Ni FGMs, which are fabricated by a centrifugal method. The micro-hardness of the aluminum matrix for Al-SiC FGM markedly increases as the volume fraction of SiC particles increases. However, the tendency is not so clear in the cases of Al-Shirasu and Al-Al{sub 3}Ni FGMs. Plastic strain energy due to thermal misfits between the matrix and dipersed particles is calculated based on an elasto-plastic analysis by applying a shell theory after Lee et al. The hardness is correlated theoretically with the composition gradient through the mean plastic strain energy (responsible for dislocation density). It is concluded that the composition gradient of ...

International Nuclear Information System (INIS)

Here we report normal-state conductance measurements of three different types of superconducting tunnel junctions that are being used or proposed for quantum computing applications: p-Al/a-AlO/p-Al, e-Re/e-AlO/p-Al, and e-V/e-MgO/p-V, where p stands for polycrystalline, e for epitaxial, and a for amorphous. All three junctions exhibited significant deviations from the parabolic behavior predicted by the WKB approximation models. In the p-Al/a-AlO/p-Al junction, we observed enhancement of tunneling conductances at voltages matching harmonics of Al-O stretching modes. On the other hand, such Al-O vibration modes were missing in the epitaxial e-Re/e-AlO/p-Al junction. This suggests that absence or existence of the Al-O stretching mode might be related to the crystallinity of the AlO tunnel barrier and the interface between ...

International Nuclear Information System (INIS)

Low-porosity #alpha#- and #beta#-SiAlON composite material was prepared when the powder mixture intended for preparation of yttrium #alpha#-SiAlON, with the formula Y_0_._4Si_1_2_-_m_+_nAl_m_+_nO_nN_1_6_- _n, was attritor milled in isopropyl alcohol or contained excess oxygen (n > 0.6). The region of stability of single-phase yttrium #alpha#-SiAlON was smaller at lower temperatures. Wet milling (in isopropyl alcohol) of AlN powder was found to introduce excess oxygen into the milled powder.

International Nuclear Information System (INIS)

Intermetallic compounds based on the Al-Co system were synthesized by solid state method - mechanical alloying and their properties were investigated using XRD, SEM, and DSC. The powder was used to make new targets of irradiation for gamma sources in order to enhance the specific activity and to reduce the consumption of material. The intermetallic compound AlCo was formed in the first 4 hours of milling. After 8 hours of milling the medium size of crystallites were of 5.58 nm. This value decreases with the increase of milling time up to 3 nm, corresponding to the 28 hours of grinding. There was calculated and plotted the Gibbs function, #DELTA#_f"0, for the reaction of formation AlCo and Al_3Co from the Al-Co system. It had negative values over the entire range of temperatures for both investigated compounds. After 28 hours milling a phase composition was obtained as follows: 0.2% ...

International Nuclear Information System (INIS)

Engineering ceramics have excellent properties such as high strength, high hardness and high heat resistance compared with metallic materials. To apply the ceramic in fast reactor environment, it is necessary to evaluate the sodium compatibility and the influence of sodium on the mechanical properties of ceramics. In this study, the influence of high temperature sodium on the mechanical properties of sintered ceramics of conventional and high purity Al_2O_3, SiC, SiAlON, AlN and unidirectional solidified ceramics of Al_2O_3/YAG eutectic composite were investigated by means of flexure tests. Test specimens were exposed in liquid sodium at 823K and 923K for 3.6Ms. There were no changes in the flexural strength of the conventional and high purity Al_2O_3, AlN and Al_2O_3/YAG eutectic composite after the sodium exposure at 823K. On the contrary, ...

British Library Electronic Table of Contents (United Kingdom)

Crystalline ?-Al2O3 nanowires with diameter, 20?40?nm, length above 600?nm and aspect ratio above 30 have been successfully synthesized by thermal decomposition of boehmite (?-AlOOH) precursors obtained via hydrothermal route by using AlCl3, NaOH and NH3 as starting materials. Thermogravimetric analysis (TG), differential thermal analysis (DTA), X-ray diffraction (XRD), transmission electron microscope (TEM), selected area electron diffraction (SAED) and high resolution transmission electron microscope (HRTEM) were used to characterize the features of the as-made ?-Al2O3 nanowires and their ?-AlOOH precursors. The pH value of the solution and the mixed precipitant play important roles in the formation of ?-AlOOH nanowires. After calcination at 500?C for 2?h, the orthorhombic ?-AlOOH transf...

Science.gov (United States)

Mg-Al mixed oxides with Mg/Al molar ratios of 0.5--9.0 were obtained by thermal decomposition of precipitated hydrotalcite precursors. The effect of composition on structure and surface and catalytic properties was studied by combining several characterization methods with ethanol conversion reactions. The nature, density, and strength of surface basic sites depended on the Al content. The catalyst activity and selectivity of Mg-Al mixed oxides in ethanol conversion reactions depended on composition. The dehydrogenation of ethanol to acetaldehyde and the aldol condensation to n-butanol both involved the initial surface ethoxide formation on a Lewis acid-strong base pair. The dehydration of ethanol to ethylene, and the coupling and dehydration to diethyl ether increased with Al content, probably reflecting the density increase of both Al{sup 3+}-O{sup 2{minus}} ...

CERN Document Server

Residual Stresses in Ta, Mo, Al and Pd Thin Films Deposited by E-Beam Evaporation Process on Si and Si/SiO 2 Substrates

International Nuclear Information System (INIS)

Aluminium nitride (AlN) is a very interesting ceramic because of its combination of properties such as high thermal stability, high hardness and an unusual combination of high thermal and low electrical conductivity. But it is very difficulty to obtain an AlN layer on the aluminium substrates by thermochemical nitriding process. Since a thin film of aluminium oxide existing on the surface of every aluminium substrate prevents the nitrogen atoms from diffusing into the aluminium lattice. However, it is possible to sputter the oxide film away from the aluminium surface in a glow discharge with the use of plasma nitriding technique and to allow the formation of AlN layer on the aluminium bulk. In the present work specimen of aluminium Al 99.5 has been plasma nitrided in a modified plasma nitriding unit, in which a diffusion pump was used to obtain an especially low partial pressure of oxygen in the vauum ...

UK PubMed Central (United Kingdom)

OBJECTIVE: To determine the common types of injuries among children (0-14 years) in Al-Ain, United Arab Emirates (UAE). DESIGN: A retrospective descriptive hospital based study. SETTING: Al-Ain Medical...Full Text Available

Science.gov (United States)

Aluminium (Al3+) toxicity is the primary factor limiting crop production on acidic soils worldwide. In addition to an application of lime for soil amelioration, Al3+ resistant plant varieties have been deployed to raise productivity on such hostile soils. This has been possible due to the exploita...

Energy Technology Data Exchange (ETDEWEB)

The authors report on the nano-fabrication of GaN/AlGaN device structures using focused ion beam (FIB) etching, illustrated on a GaN/AlGaN heterostructure field effect transistor (HFET). Pillars as small as 20nm to 300nm in diameter were fabricated from the GaN/AlGaN HFET. Micro-photoluminescence and UV micro-Raman maps were recorded from the FIB-etched pattern to assess its material quality. Photoluminescence was detected from 300nm-size GaN/AlGaN HFET pillars, i.e., from the AlGaN as well as the GaN layers in the device structure, despite the induced etch damage. Properties of the GaN and the AlGaN layers in the FIB-etched areas were mapped using UV Micro-Raman spectroscopy. Damage introduced by FIB-etching was assessed. The fabricated nanometer-size GaN/AlGaN structures were found to be of good quality. The results demonstrate the ...

International Nuclear Information System (INIS)

Reactive milling of NiO + Al powder mixture resulted in the formation of NiAl-Al_2O_3 nanocomposite powders, with a crystallite size of about 20 nm. The Hall-Williamson analysis revealed that NiAl showed an orientation dependent crystallite size after short processing time and orientation dependent internal strain after long milling time. Both anisotropies were removed by heating the powders in the differential scanning calorimetry. Calorimetric studies showed one exothermic effect attributed to the reduction reaction of NiO and endothermic one associated with melting of Al. Two methods were applied for powders compaction: resistance sintering and pulse electric discharge. In both cases the densities of abut 90% of the theoretical value were achieved. A significant increase in average NiAl crystallites size in compacted samples was observed, up to several hundreds of ...

British Library Electronic Table of Contents (United Kingdom)

A Ni3Al coating was prepared by plasma spraying technique on the surface of titanium alloy. Ni-Al mixed powders, coatings and reaction products were investigated by scanning electron microscope, EDS, DSC and XRD. A tight bonding between the coating and the substrate was formed. The X-ray diffraction analysis of the patterns showed that the coating not only had Ni3Al phase, but also had NiO and Al2O3 phase microcontent. Comparing Ni coated Al to Ni3Al at 900^oC, the diffusion was stronger and the diffusion layer was thicker. A minute pore structure was formed at 1200^oC in the front edge of solid-state reaction layer. So Ni3Al restrained the solid-state reaction of the coating with the substrate, and as a whole weakened the entry of oxygen atoms into the substrate and quenched the out-diffu...

International Nuclear Information System (INIS)

A microwave-assisted carbothermal reduction and nitridation (CTR/N) method has been used for successful preparation of monophasic #beta#'-SiAlON starting from kaolinite and carbon black. Phase pure #beta#'-SiAlON has been obtained in under 60 min in microwave field. The z value of microwave prepared #beta#'-SiAlON is found to be 2.95, which is very close to the expected value from kaolinite composition. Formation of #beta#'-SiAlON has been monitored with XRD and MASNMR of "2"9Si and "2"7Al; the possible reaction mechanism has been discussed. Kaolinite to #beta#'-SiAlON conversion appears to be a very rapid single-step reaction under microwave irradiation. #beta#'-SiAlON powders have been microwave sintered to 98.7% of theoretical density in 30 min.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

English 2006 2 p. Brazil Rocha, RM Centro Tecnico Aeroespacial, Sao

Science.gov (United States)

... to Indonesia, and Indonesians who once worked in the Arabian Gulf region (Gunaratna 2003, 269-270). These workers ...

International Nuclear Information System (INIS)

English Mar 1999 [vp.] United Kingdom Jumali, MHH Warwick Univ.,

International Nuclear Information System (INIS)

... dpg-tagungen.de Dresden (Germany) 27-31 Mar 2006 0420-0195 VDPEAZ

Science.gov (United States)

Recently, Wang et al. proposed a three-party simultaneous quantum secure direct communication (3P-SQSDC) scheme with EPR pairs, which enables three involved parties to exchange their secret messages simultaneously by using an EPR pair. This work proposed an enhancement on Wang et al.'s scheme. With the enhancement, the communications in the improved 3P-SQSDC can be paralleled and thus improves the protocol efficiency.

International Nuclear Information System (INIS)

Immobilization of long-lived fission products (LLFP) such as radioactive Tc, Cs and Sr into #alpha#-SiAlON ceramics was evaluated using stable isotopes instead of radioactive isotopes, and the applicability of #alpha#-SiAlON ceramics as the inert matrix for transmutation of LLFP was investigated. In the case of single addition of SrO, SrCO_3, Cs_2CO_3 or ReO_2 to the starting materials, #alpha#-SiAlON, single phase was not formed after hot-pressing. When Y_2O_3 was added with SrO, SrCO_3 or Cs_2CO_3 to the starting materials (#alpha#-Si_3N_4, AlN and #alpha#-Al_2O_3) in optimum compositions, #alpha#-SiAlON single phase was obtained after hot-pressing at 1700degC or 1800degC. From the EDS analysis, Sr and Y were detected from grains. It is suggested that Y would assist the expansion of interstices of #alpha#-SiAlON lattice, resulting in the ...

International Nuclear Information System (INIS)

The ErNi_1_- _x Cu _x Al compounds crystallize all in the hexagonal ZrNiAl-type structure. The concentration dependence of lattice constants shows a discontinuity between x=0.5 and 0.6. This structural change has no primary impact on the magnetic order in this series, but influences the crystal field. The lower part of the crystal-field energy-level schemes has been estimated from the specific-heat data.

British Library Electronic Table of Contents (United Kingdom)

Direct visualization of rare earths in @a- and @b-SiAlON unit-cells is performed through Z-contrast imaging technique in an aberration-corrected scanning transmission electron microscope. The preferential occupation of Yb and Ce atoms in different interstitial locations of @b-SiAlON lattice is demonstrated, yielding higher solubility for Yb than Ce. The triangular-like host sites in @a-SiAlON unit cell accommodate more Ce atoms than hexagonal sites in @b-SiAlON. We think that our results will be applicable as guidelines for many kinds of rare-earth-doped materials.

Energy Technology Data Exchange (ETDEWEB)

The local strain and texture in Al interconnect wires have been investigated using white and monochromatic x-ray microbeams on the MHATTCAT undulator beam line at the Advanced Photon Source. Intergrain and intragrain orientations were obtained with ~0.01 degree sensitivity using white beam measurements on wide Al pads (~100 Mu-m) and thin (2 Mu-m) Al wires. Orientation changes of up to 1 degree were found within individual grains of the (111) textured Al interconnects. Deviatoric strain measurements indicate small intragranular strain variations, but intergranular strain variations were found to be quite large.

International Nuclear Information System (INIS)

The thermal transformation of Al-base icosahedral phases was studied in-situ by real time neutron powder diffraction. Different compositions have been selected in order to vary the initial phase morphology and change the neutron scattering contrast between species. Alloys with low silicon and large aluminium contents produce first the orthorhombic O-Al_6Mn modification. In alloys with larger silicon content, the #alpha#-AlMnSi cubic phase appears soon after the beginning of the transformation but is still preceeded by O-Al_6Mn. Depending on compositions, the crystallization of the icosahedral phase is controlled either by the diffusion of Al through its interface with the residual fcc aluminium or that of Si within the bulk. The results are discussed in the light of current structural models. (author) 40 refs., 14 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

GaP and AlGaP were grown by atmospheric pressure OMVPE on GaP substrates using tertiarybutylphosphine as the phosphorus source. A specular surface of GaP was obtained on a (100) just-oriented surface at 700deg C. Hazy but uniform thickness AlGaP was obtained. The growth efficiency for GaP was 1.2x10{sup 3}{mu}m/mol and that for AlGaP was 2.1x10{sup 3}{mu}m/mol.4.2 K photoluminescence showed near-edge emission from both GaP and AlGaP. (orig.).

British Library Electronic Table of Contents (United Kingdom)

An impingement jet system was used to study flow-assisted corrosion (FAC) of 3003 aluminum (Al) alloy in ethylene glycol-water solutions that simulates the automotive coolant by corrosion potential and electrochemical impedance spectroscopy (EIS) measurements as well as computational fluid dynamics (CFD) simulation. The effects of solution pH and fluid impact angle on Al FAC were determined. An increase of solution pH enhances the activity of Al due to dissolution of Al oxide film in alkaline environment. Moreover, Al activity decreases with the increasing fluid impact angle to the specimen. A CFD simulation shows that, with the increase of impact angle, the electrode area under high-velocity flow field decreases and that under low-velocity flow field increases. Consequently, the shear str...

Energy Technology Data Exchange (ETDEWEB)

A body-centered cubic (bcc) Mg-12Li-9Al-1Zn (wt.%) alloy was fabricated in air by electrolysis from LiCl-KCl molten salt at 500 deg. C. Electrolytic deposition of Li atoms on cathode (Mg-Al-Zn alloy) and diffusion of the Li atoms formed the bcc Mg-Li-Al-Zn alloy with 12 wt.% Li and only 0.264 wt.% K. Low K concentration in the bcc Mg alloy strip after the electrolysis process resulted from 47% atomic size misfit between K and Mg atoms and low solubility of K in Mg matrix.

Energy Technology Data Exchange (ETDEWEB)

In this paper, we discuss various aspects of the development of an inverted-grown AlGaAs/GaAs cascade solar cell incorporating a patterned germanium tunnel junction. Topics include the development of the Al{sub 0.37}Ga{sub 0.63}As top cell, the growth of the GaAs bottom cell over the patterned germanium tunnel junction, and a technique for selective removal of thin AlGaAs/GaAs heterostructures after lattice-matched growth on germanium substrates. The problems to be overcome for the achievement of around 30% efficiencies in the AlGaAs/GaAs cascade cell under concentrator applications are also discussed. (orig.).

Energy Technology Data Exchange (ETDEWEB)

FeAl, which has high oxidation and sulfidation resistance, was shown to be thermodynamically compatible with WC. Calculations indicate that soly. of WC in liq. Fe-40at.%Al at 1450 C is about 2 at.%. Since liquid FeAl wets WC very well, the WC/FeAl system lends itself to liquid-phase sintering, resulting in close to theoretical densities. Almost fully dense cermets with 20.6 wt% FeAl binder were produced. With one-step infiltration, 98% dense cermets with only 7 wt% FeAl binder were fabricated. RT bend strengths and fracture toughness for WC-20.6 wt% FeAl reached 1680 MPa and 22 MPa{center_dot}m{sup 1/2}. Ductile binder fracture was observed on the fracture surfaces. Pores containing oxide inclusions were found, suggesting that improvements in processing are likely to further improve the mechanical properties. Insufficient process control may ...

International Nuclear Information System (INIS)

The occurrence of stable decagonal quasicrystalline phase in Al-Co-Ni and Al-Cu-Co alloys through conventional solidification is well established. Earlier, we have studied the effect of Cu substitution in place of Co in the Al_7_0Co_1_5Ni_1_5 alloy. Here we report the structural/micro-structural changes with substitution of Cu for Ni in rapidly solidified Al-Co-Ni alloys. The melt spun ribbons have been characterized using X-ray diffractometry, scanning and transmission electron microscopy. With an increase in Cu content in the melt spun Al_7_0Co_1_5Cu _xNi_1_5_-_x (x = 0-15 at.%) alloys, the relative amount of the decagonal phase decreased up to 10 at.% of Cu. At this composition, the quaternary alloy showed the co-existence of decagonal quasicrystal and superstructure of #tau#_3 vacancy ordered crystalline phases. The decagonal phase containing Cu showed more disordering than ...

International Nuclear Information System (INIS)

Inductively coupled plasma etching of InGaP, AlInP and AlGaP in BI_3 or BBr_3 discharges was investigated as a function of source power, dc chuck bias and plasma composition. InGaP etches at the fastest rates (>6000 Angstrom min"-"1) in both chemistries, followed by AlGaP. It is found that AlInP provides an excellent etch stop for the other two materials in both mixtures. The InGaP surface morphology improves with increasing BI_3 or BBr_3 content, and with increasing dc chuck bias. The etched features for this material are highly anisotropic. Etch selectivities for InGaP over SiO_2 and SiN_x of #>=#8 are obtained in both plasma chemistries, and there is no etch incubation time with either mixture, indicating that both can scavenge the native oxide on InGaP, AlGaP and AlInP. copyright 1998 American Vacuum Society.

Energy Technology Data Exchange (ETDEWEB)

Focus ion beam (FIB) technology is a commonly used tool for integrated circuit device modification, failure analysis, and a variety of other applications. However, limited reliability data of FIB altered circuit is available. This study describes the electromigration mechanism of FIB-altered Al(Cu-Si)/Ti-layered metal lines. The electromigration failures encountered resulted in Al voids at the anode end of FIB-deposited W and Al{sub 2}Cu precipitates at the cathode end. A higher frequency of Al extrusions was also observed on samples stressed at higher temperatures. These observations indicated that FIB-W was an effective blocking boundary for Al and Cu, and confirmed that Cu does electromigrate before Al. The electromigration mechanism of the FIB-altered line closely resembles the published results from two-level Al/W-line/stud interconnect ...

Energy Technology Data Exchange (ETDEWEB)

Cyclic voltammetry (CV), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were employed to investigate the electrodeposition of Eu and Al in an LiCl-KCl eutectic melt containing Eu{sup 2+} and Al{sup 3+} at 450 deg. C. In order to deposit a pure Eu and Al alloy, the stoichiometrically lower concentration of Al{sup 3+} than that of Eu{sup 2+} and Al wires as a counter electrode was introduced into the bath of LiCl-KCl melt for the electrodeposition. The electrodeposition takes place at a potential more negative than -1.95 V vs. Ag|Ag{sup +} while the deposit is oxidized at more positive potential than -1.92 V. Two new reduction peaks and an anodic peak on a W working electrode were observed at -2.39 V, -2.42 V, and -2.1 V, vs. Ag|Ag{sup +}, respectively, suggesting that the potential window of the Al system in LiCl-KCl melt can be ...

Energy Technology Data Exchange (ETDEWEB)

Hexavalent Cr has been identified as one of the toxic metals commonly present in industrial effluents. Among the treatment techniques developed for removing Cr(VI) from waste waters, sorption is most commonly applied, due to its simplicity and efficiency. However, few adsorbents can be recycled and reused cost-effectively. In this study, the removal and recovery of Cr(VI) from water using Li/Al LDH was investigated. The removal of Cr(VI) by Li/Al LDH was evaluated in a batch mode. The results demonstrated that Cr(VI) adsorption onto Li/Al LDH occurs by replacing the Cl{sup -} that originally exists in the interlayer of the adsorbent. The degree of Cr(VI) adsorption observed for Li/Al LDH was relatively high and the process occurred rapidly; however, a portion of adsorbed Cr(VI) was gradually desorbed, due to the Li de-intercalation of Li/Al LDH. Lithium de-intercalation from ...

International Nuclear Information System (INIS)

We describe the growth, fabrication, and characterization of an ultraviolet (UV) photoconductive detector based on In_xAl_yGa_1_-_x_-_yN quaternary alloy that is lattice matched to GaN. The detector consisted of 0.1 #mu#m In_xAl_yGa_1_-_x_-_yN alloy grown on 0.5-1.0 #mu#m GaN epilayer by metalorganic chemical vapor deposition. With varying indium concentration, the cut-off wavelength of the In_xAl_yGa_1_-_x_-_yN detectors could be varied to the deep UV range. The most important and intriguing result is that the responsivity of the In_xAl_yGa_1_-_x_-_yN quaternary alloy exceeded that of AlGaN alloy of a comparable cutoff wavelength by a factor of five. This makes the nitride quaternary alloy very important material for solar blind UV detectors applications particularly in the deep UV range where Al rich AlGaN alloys have problems with low ...

International Nuclear Information System (INIS)

A one-nanometer scale transmission electron microscope electron probe X-ray microanalysis characterization of as-deposited and annealed aluminum--11.5 at.% zirconium multilayer samples in cross-section synthesized by magnetron sputtering is reported on here. Composition line profiles were acquired across Zr layers in as-deposited material and samples isochronally annealed in a differential scanning calorimeter to temperatures of 290 C and 485 C. A spatial resolution of approximately 1.5 to 2.0 nm was achieved in these experiments and will be improved by deconvolution of the instrumental electron probe function from the data. The as-deposited structure consisted of crystalline Al and Zr layers with thin amorphous layers at the Al/Zr interfaces. The amorphous interface layers increased in thickness upon annealing to 290 C. Additionally, at 290 C a metastable cubic alloy forms at the Zr deposited on Al interface. Upon heating ...

Energy Technology Data Exchange (ETDEWEB)

The effect of interfacial structure on the mechanical properties of aluminum-ceramic composite materials fabricated by liquid phase sintering was studied. The composites were based on two matrix alloys (powder metallurgy alloys 201 and 601) reinforced with either Al{sub 2}O{sub 3} or SiC particulate. Characterization of the interfacial regions demonstrated that the SiC-matrix interfaces were faceted whereas the Al{sub 2}O{sub 3}-matrix interfaces had an incomplete layer of a silicon-rich amorphous phase. Preferential attack of the particles during sintering is believed to cause the crystallographic facets to form on SiC. Locally high silicon concentrations near Al{sub 2}O{sub 3} particles led to the formation of a glassy phase from the reduction of Al{sub 2}O{sub 3}. The difference in interfacial structure resulted in a higher particle-matrix bond strength and therefore improved composite mechanical ...

British Library Electronic Table of Contents (United Kingdom)

Abstract A next generation material for surface passivation of crystalline Si is Al2O3. It has been shown that both thermal and plasma-assisted (PA) atomic layer deposition (ALD) Al2O3 provide an adequate level of surface passivation for both p- and n-type Si substrates. However, conventional time-resolved ALD is limited by its low deposition rate. Therefore, an experimental high-deposition-rate prototype ALD reactor based on the spatially separated ALD principle has been developed and Al2O3 deposition rates up to 1.2-nm/s have been demonstrated. In this work, the passivation quality and uniformity of the experimental spatially separated ALD Al2O3 films are evaluated and compared to conventional temporal ALD Al2O3, by use of quasi-steady-state photo-conductance (QSSPC) and carrier density ...

International Nuclear Information System (INIS)

The pozzolanic behaviour of compound-activated red mud-coal gangue has been investigated through TG, DTA, XRD, FTIR and 27Al MAS NMR. From viewpoint of reaction kinetics, it is found that the pozzolanic reaction mechanism of the compound-activated red mud-coal gangue - lime system is clearly consistent with diffusion control up to 14 days, and the reaction rate constant calculated from Jander equation decreases with the increase of CaO addition in the system. The hydration products formed in the red mud-coal gangue - lime systems at ambient temperature are essentially aluminous C-S-H and Ca3Al2O6.xH2O. From TG analysis results, it is thought that the high amount of Ca(OH)2 in the pastes of studied system is not conducive to the continual increase of non-evaporable water content of the hydration products. Of particular interest, 27Al MAS NMR proved to be an effective technique to obtain valuable information of ...

Energy Technology Data Exchange (ETDEWEB)

In this review, the most important inorganic natural gels are presented: opal, aluminosilicate (allophanes) and hydrous iron oxides and silicates. It is demonstrated that natural gels are ordered at the atomic scale. In allophanes, Al is distributed between octahedral and tetrahedral sites. The amount of Al increases as Al/Si ratio decreases. Si-rich allophane have a local structure around Al and Si very different of that is known in kaolinite or halloysite. Transformation of Si-rich allophanes to crystallized minerals implies dissolution-recrystallization processes. On the contrary, in iron silicate with Fe/Si = 0.72, Si and Fe environments are close to those found in nontronite. The gel transformation to Fe-smectite may occur by long range ordering during ageing. In ferric silicate gels, the similarity of local structure around Fe in poorly ordered precursors and what is known in crystallized minerals ...

Energy Technology Data Exchange (ETDEWEB)

TiAl with between 0 and 20 volume percent (v%)Ti5Si3 was produced by reactive sintering of cold pressed compacts of elemental Ti, Al and Si powder mixtures at 700C for 15 minutes in vacuum. The results show that adding Si to Ti and Al reduces the swelling associated with reactive sintering of TiAl, as composites containing more than 5 v%Ti5Si3 densified during reactive sintering. However, composites containing more than 10v% Ti5Si3 did not retain their shape during processing, and the TiAl+20v% Ti5Si3 composite completely melted during the sintering process. The formation of pre-reaction liquid phase and the increase in adiabatic flame temperature with simultaneous compound formation resulted in the melting that occurred and the enhanced densification (minimization of swelling) during reactive sintering of the insitu composites.

Energy Technology Data Exchange (ETDEWEB)

Glass-ceramic materials containing 0-60% glass, 0-40% cordierite and 0-40% mullite were developed with dielectric constant lower than of Al{sub 2}O{sub 3} (5.2-6.7). The following glasses were used: SiO{sub 2}, CaO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-SiO{sub 2}, CaO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}, CaO-ZnO-B{sub 2}O{sub 3}, CaO-ZnO-Al{sub 2}O{sub 3}B{sub 2}O{sub 3}, BaO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-SiO{sub 2} and BaO-ZnO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-SiO{sub 2}. The influence of the content of the particular components on the value of dielectric constant of the ceramics was investigated. (author). 9 refs, 3 tabs.

International Nuclear Information System (INIS)

Research is in progress to obtain a satisfactory creep ductility for alloy 800 when used as heat exchanger material in sodium-cooled fast reactors (LMFBR). The creep test characteristics at present available show that a pronounced tendency to reduced elongation by creep failure may arise after prolonged testing in the 500-700 deg C temperature range. This phenomenon is now agreed to be primarily inherent to the conditions for Ni_3(Ti,Al) precipitation in the material and hence to the Ti and Al concentrations. By structural studies and hardness measurements on material subjected to creep tests and taken from a large number of castings, the relationship was established between the (Ti+Al) content and the structural hardness effect of Ni_3(Ti,Al) at 600 deg C. Below a certain Ti+Al concentration, no precipitation occurs and hence the creep ductility to failure can be improved ...

Energy Technology Data Exchange (ETDEWEB)

In order to understand the anodic behaviour of Al--Mo and Al--W amorphous alloys in the borate buffer electrolyte, samples of these alloys were polarized galvanostatically. The resultant anodic films were thicker than the passive films formed during potentiodynamic polarization enabling detailed examination of the films and alloy substrates by surface analytical methods. AES investigations suggest that the anodic films formed at low and moderate voltages on Al--Mo or Al--W amorphous alloys consist of Al-oxide, whereas refractory metals remain unoxidized and enriched at the film/substrate interface. Molybdenum and tungsten act as 'dissolution moderators', restraining the substrate dissolution process at the film/substrate interface. However, after anodization at high voltages (50 V), AES revealed the presence of an oxidized refractory metal in the inner part of the ...

Energy Technology Data Exchange (ETDEWEB)

Laser surface alloying with gaseous nitrogen was utilized to improve the wear resistance of a Ti-6Al-4V alloy. Wear-resistant composite coatings reinforced by hard TiN dendrites were produced 'in-situ' on a substrate of a Ti-6Al-4V alloy. The hardness and wear resistance of the laser alloyed coating under two-body abrasive and block-on-ring full-sliding wear conditions were significantly enhanced. (orig.)

International Nuclear Information System (INIS)

The A-15 compounds with the highest critical temperatures and critical fields are stable only at high temperatures and sometimes are not stable at any temperature. Fabrication of such materials thus necessarily involves the creation and manipulation of metastable phases. It follows that the bronze matrix technique now under development for Nb_3Sn- and V_3Ga-based composite superconductors is not suitable for high-T/sub c/ materials of the Nb_3 (Al, Ge, Ga, Si) family. Alternative technologies will be necessary for such materials. Efforts to develop suitable alternatives, using Nb_3Al, are described.

Energy Technology Data Exchange (ETDEWEB)

A local Heine-Abarenkov model potential is proposed for zinc blende-type crystals. The potential parameters are determined by satisfying the zero pressure condition and the first zero of the empirical pseudopotential interpolated from band calculations. Two sets of parameters are presented for thirteen tetrahedral compounds such as AlP, AlAs, AlSb, GaP, GaAs, GaSb, InP, InAs, InSb, ZnS, ZnSe, ZnTe, and CdTe.

International Nuclear Information System (INIS)

This paper describes the performance of AlGaN/GaN HEMTs with 2.4 #mu#m source-drain spacing. So far these are the smallest source-drain spacing AlGaN/GaN HEMTs which have been implemented with a domestic wafer and domestic process. This paper also compares their performance with that of 4 #mu#m source-drain spacing devices. The former exhibit higher drain current, higher gain, and higher efficiency. It is especially significant that the maximum frequency of oscillation noticeably increased. (semiconductor integrated circuits)

Energy Technology Data Exchange (ETDEWEB)

Evaluation of grain boundary composition and structure in superplastically deformed AA5083-based alloys (Al-4.5Mg-1.6Mn-0.2Zr) was carried out in a field-emission gun transmission electron microscope (FEG-TEM). During superplastic deformation at high homologous temperatures materials undergo extensive grain boundary sliding (GBS) which creates a flow of defects in the near-boundary region. Recent literature has shown that the grain-boundary composition in Al-Mg alloys is not necessarily the same as the matrix, and that these differences can have an effect on GBS.

Science.gov (United States)

This article examines problems relating to the calculation of the position of regions of limited solubility of components in the liquid state for four-component systems. An approach based on the use of criterion of stability with respect to diffusion for obtaining equations which describe the region of stratification of the liquid phase in a four-component system is used. The authors used a ES-1020 computer to analyze the critical phenomena in Al-In-P-Sb, Al-Ga-In-P, Al-Ga-In-As, and In-Ga-As-P systems. The position of the spinode in the phase diagram of a four-component system is obtained.

International Nuclear Information System (INIS)

Al, Ga and In complexing with methylthymol blue (H_6R) purified by gel filtration is studied. in the case of metal excess complexes with the ratio of components M:H_6R=2:1 with #lambda#=587(Al), 590(Ga) and 593 nm(In) appear. In the case of reacting agent excess complexes with the ratio of component 1:1 with #lambda#_m_a_x=480-490 (Al) and 480 nm(Ga, In) appear. The mechanism of complexing reactions is studied. Molar extinction coefficients and stability constants are calculated.

Science.gov (United States)

partnerships led to the passage of a legislation creating a stormwater authority with Baldwin County, AL. The Coastal Training Program provides up-to-date scientific information...

Science.gov (United States)

... Accession Number : ADD135317. Title : Workability and Heat Treatment Characteristics of Beta Titanium Alloy, Ti-15V-3Cr-3Sn-3Al,. ...

Science.gov (United States)

Lake Unit AL-05P, for public review and comment. These four CBRS units are located in Baldwin and Mobile Counties, Alabama. We invite the public to review and comment on the draft...

Energy Technology Data Exchange (ETDEWEB)

An Fe-19Cr-8Al-0.5Hf alloy has been roll bonded to Alloy 800 to form a protective clad material suitable for use in coal conversion atmospheres. The commercial producibility of both the Fe-19Cr-8Al-0.5Hf alloy and the clad composite has been demonstrated. The clad composite has been shown to exhibit resistance to sulfidation in high sulfur, coal gasification atmospheres low Btu for 2000 hrs at 1800/sup 0/F (1255K). The FeCrAlHf alloy must be preoxidized in the absence of sulfur to form fully protective alumina scales on all surfaces. Useful life of the composite at temperatures of 1400 to 2000/sup 0/F (1033 to 1366K) is governed by reactions at the FeCrAlHf clad alloy 800 interface. The rate of interdiffusion decreases with increasing Ni content and a high Ni alloy such as RA333 appears to be a better substrate than Alloy 800 for a FeCrAlHf composite. The mechanical properties of ...

British Library Electronic Table of Contents (United Kingdom)

The age hardening behavior of Al-4.5%Cu alloy composite reinforced with zircon sand particulates and produced by stir casting route has been investigated in different quenching media viz, water, oil, and salt brine solution (7wt%). Optical microscopy of the as cast alloy composite indicates that the matrix of the composite has the cellular structure. Copper rich CuAl2 precipitates have been found near particle matrix interface. The results of ageing demonstrate that the microhardness of age hardenable Al-Cu based alloy composites depend on the quenching medium in which they are heat treated. Salt brine quenching is faster as compared to water and oil, even if higher strength is obtained but cannot be used for complex shapes and thin sections where oil quenching is the alternative due to mi...

Science.gov (United States)

... Mirrors (Preprint) Ryan Conk et al. 15 September 2006 ... 4. TITLE AND SUBTITLE Stress Coatings for Large Scale Membrane Mirrors (Preprint) 5a. ...

Science.gov (United States)

Eckert, B., "Axial Kompressoren und Radial Kompressoren," Springer. Verlag, Berlin, 1953. 3. Lebot, Y., et al., "Theoretical and Experimental Determination ...

Science.gov (United States)

This paper summarizes the main features of four current REDD proposals: Compensated Reduction, Papua New Guinea et al; Joint Research Center; and Brazil. ... ...

Science.gov (United States)

... at compositions below -AlP 4 the films were still unstable, hydrolysing in room air, and the long term stability of higher aluminium phosphides is in ...

British Library Electronic Table of Contents (United Kingdom)

Porous ?-SiAlON ceramics are synthesized by reaction bonded method using hollow alumina spheres (HASs) as both sintering aids and pore-forming agents. Both micropores and macropores, which are constructured by SiAlON grains with different morphologies, are formed in the final SiAlON samples. The micropores are three-dimentional, and are built by equiaxial grains. While the hollow macropores, which have the similar morphology to hollow alumina sphere, are packed by elongated grains. In the sintering process, the solid dissolution process takes place, giving rise to the different alumina concentration of liquid phase, and thus resulting in the formation of two kinds of grains, the equiaxial grain and the elongated grain.

Science.gov (United States)

Homogenous Al{sub x}Ga{sub 1{minus}x}P liquid phase epitaxial layers have been obtained with the temperature difference method under controlled vapor pressure (TDM-CVP). Very clear fine structures near band edge in photoluminescence spectra have been observed at 77 K for the first time. Photoluminescence measurement results confirmed that the free exciton recombination without phonon assistance plays an important role in the luminescence at 77 K and becomes dominant at room temperature. It is considered that Zero-phonon assisted free exciton recombination is intensified by some local perturbations to electrical potentials against carriers or excitons introduced by Al atoms in Al{sub x}Ga{sub 1{minus}x}P layers, which can give momentum change necessary for recombination.

International Nuclear Information System (INIS)

Forster et al. recently showed that weak nonlocality can be amplified by giving the first protocol that distills a class of nonlocal boxes (NLBs) [Phys. Rev. Lett. 102, 120401 (2009)] We first show that their protocol is optimal among all nonadaptive protocols. We next consider adaptive protocols. We show that the depth-2 protocol of Allcock et al. [Phys. Rev. A 80, 062107 (2009)] performs better than previously known adaptive depth-2 protocols for all symmetric NLBs. We present a depth-3 protocol that extends the known region of distillable NLBs. We give examples of NLBs for which each of the Forster et al., the Allcock et al., and our protocols perform best. The understanding we develop is that there is no single optimal protocol for NLB distillation. The choice of which protocol to use depends on the noise parameters for the NLB.

Science.gov (United States)

... potential propagation in terminal nerve fibers or at the neuromuscular ... means of prosthesis control (Graupe, et al, 1975). ... parallel interface, a joystick ...

Science.gov (United States)

... that range from relatively low frequency strong ground motion modeling [Vidale et al., 1985] to high frequency reverse time migration of seismic ...

International Nuclear Information System (INIS)

1972. United States Narayanan, GH Archbold, TF Univ. of California Press.;

International Nuclear Information System (INIS)

With the assistance of mechanical activation, yttrium-stabilized #alpha#-SiAlON was prepared by combustion synthesis in air, instead of high-pressure N_2 atmosphere for the first time. The reaction activity of metallic particles was remarkably enhanced by mechanical activation, which conduced the reduction of grain size, increased the total surface area and formation of fresh surface. The formation of #alpha#-SiAlON by combustion synthesis in air was explained by a kinetically induced reaction mechanism, in which both initial formation of #alpha#-SiAlON and following avoidance of oxidation were fulfilled by the retardation of O_2 infiltration owing to the short reaction period and fast cooling rate.

British Library Electronic Table of Contents (United Kingdom)

Yb-, Y-, Yb/Y-, and Yb/Nd-doped -SiAlON ceramics with 5-wt% barium aluminosilicate (BAS) were synthesized by hot pressing. Typical self-reinforced microstructures were obtained in all investigated -SiAlONs in spite of the type of doped cations. This is attributed to the incorporation of BAS, which could supply suitable liquid phase to promote the anisotropic growth of the -SiAlON grains. All the composites exhibited excellent high-temperature mechanical properties and thermal shock resistance due to the formation of a self-reinforced microstructure and the complete crystallization of BAS additive.

Energy Technology Data Exchange (ETDEWEB)

We report the lasing characteristics of gain-guided AlGaInP/AlGaAs visible vertical-cavity surface-emitting laser diodes. At room temperature, continuous-wave operation is achieved over the wavelength range of 657--685 nm with the minimum threshold current at 670 nm. Devices with a 10-[mu]m diameter have threshold currents as low as 1.25 mA at room temperature (297 K) and 0.8 mA at 250 K. In addition, a single predetermined linear polarization state is found, independent of the lasing mode order and operating temperature.

International Nuclear Information System (INIS)

DZ4 substrates were coated with NiCoCrAlY by plasma spray and subsequently treated by high current pulsed electron beams(HCPEB) of different parameters. The surface microstructure, phase structure and high temperature oxidation resistance were studied. It has been shown that as a result of the HCPEB treatment the loose and rough structure remelted and the surface became smooth. Smooth microregion, craters and cracks appeared on the surface. The ?' phase manifolded and there was no visible thermal stress. The oxidation test at 900 degree C for 100 h showed that a more compact and successive ?-Al_2O_3 scale was formed on the surface of the samples after HCPEB irradiation, which improved the oxidation resistance of the NiCoCrAlY coatings obviously. (authors)

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... Accession Number : ADD442819. Title : Instrumeted Impact Testing of Composite Sandwich Panels,. Corporate Author : AUBURN UNIV AL. ...

International Nuclear Information System (INIS)

... INIS-UA--158 488 p. MATERIALS SCIENCE additives aluminium oxides

Energy Technology Data Exchange (ETDEWEB)

Nd{sub 40}Fe{sub 30}Al{sub 10}Co{sub 15}B{sub 5} alloys were fabricated by high energy ball milling method under various conditions. Microstructure of the alloys was investigated by X-ray diffraction and electron microscopy techniques. Magnetic properties were characterized by hysteresis and thermomagnetic measurements. The high coercive fields up to 2.36 T have been observed on the samples consisting of Nd{sub 2}(Fe,Co,Al){sub 14}B, Nd{sub 6}(Fe,Co,Al){sub 14} and Nd crystallites imbedded in a residual amorphous matrix.

Science.gov (United States)

Oberpfaffenhofen, Pedel"al aepublic of Gel1lany. A large number of European scientists have provided ex~eri- ments that will be cooducted in the Material ...

Science.gov (United States)

Excitonic transitions in metalorganic vapor phase epitaxially grown In[sub [ital x

Energy Technology Data Exchange (ETDEWEB)

Effects of the addition of precious metals (PM; Pt, Rh) on CeO{sub 2}/Al{sub 2}O{sub 3} and CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} were confirmed to enhance the oxygen storage capacities (OSC). Increments in the OSC of the added CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} catalysts were much greater than those in the OSC of the PM added CeO{sub 2}/Al{sub 2}O{sub 3}. The enhanced OSC is ascribed to the interaction between PM and a CeO{sub 2}-La{sub 2}O{sub 3} solid solution formed during the catalyst preparation. No enhancements in the OSC were observed on physical mixing of CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} and Pt-Rh/Al{sub 2}O{sub 3}, although the composition ratio of PM:CeO{sub 2}:La{sub 2}O{sub 3} is the same as that in the PM added CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3}. This indicates that the intimate ...

International Nuclear Information System (INIS)

Passivity of aluminum (Al) alloy 3003 in air and in aqueous solutions without and with chloride ions was characterized by electrochemical measurements, including cyclic polarization, electrochemical impedance spectroscopy (EIS), localized EIS and potential of zero charge, Mott-Schottky analysis and secondary ion mass spectroscopy (SIMS) technique. Stability, pitting susceptibility and repassivation ability of Al alloy 3003 under various film-forming conditions were determined. Results demonstrated that passive films formed on 3003 Al alloy in air and in Na2SO4 solution without and with NaCl addition show an n-type semiconductor in nature. The passive film formed in chloride-free solution is most stable, and that formed in chloride-containing solution is most unstable, with the film formed in air in between. Pitting of Al alloy 3003 passivated both in air and in aqueous solutions is inevitable in the ...

Science.gov (United States)

... Accession Number : ADA137272. Title : Effects of Yttrium Microalloying on the Epitaxial Grain Growth in Ti-6Al-4V Weld Fusion Zones. ...

Science.gov (United States)

closure of the BISON network, GOLF and VIRGO will remain the only instruments ...... Faraday Cup solar wind instrument as described in Ipavich et al (1998). ...

International Nuclear Information System (INIS)

Portuguese 2004 p. 187 Brazil Santos, C. Strecker, K. Suzuki, PA

British Library Electronic Table of Contents (United Kingdom)

Ultrasonic gold and aluminum wire wedge bonding are widely used for electrical and signal interconnections of the integrated circuit chip packages. In this paper, based on the metallurgical theories and thermal aging test methods, the long-term thermal reliabilities of gold and aluminum wire wedge bonding on aluminum and Au/Ni/Cu pads, were investigated, respectively. At 200degreeC, the Au/Al bond interfaces evolved little when the storage time was less than 48h; with the aging time increasing, the interfacial intermetallic compounds (IMC) grew up from the pad (vertical growth); the primary compounds were Au5Al2 near the bond toe and heel, and Au2Al at the periphery. Then, the thickness of IMC was unchanged, and extended horizontally (lateral growth), Au5Al2 transformed into more stable Au...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The high temperature abrasive wear resistant of the composites with different Al{sub 2}O{sub 3} volume fractions, particle coating and size were investigated and the failure action of composites under different conditions at high temperature was analyzed. The results showed that the high temperature abrasive wear resistant of composite with Ni coating and wide size and 39% volume fraction of particle is the best among all composites examined. (orig.)

International Nuclear Information System (INIS)

The wavelength dependence of the threshold in an InGaP-InAlGaP vertical cavity surface emitting laser is investigated using a microscopic theory of the semiconductor gain medium. Good agreement is found between experiment and theory for the minimum threshold lasing wavelength for a range of laser structures.

Energy Technology Data Exchange (ETDEWEB)

Superconducting thin film particle detectors can be very attractive due to the low sensitivity to radiation damage. We describe the fabrication procedure and the characterization of Nb/Al bilayers as particle detectors. First steady and dynamical results are reported from tests of 5 MeV alpha-particle detection.

International Nuclear Information System (INIS)

The alloy of Ti-Al-Mo-V-Cr system is studied for its structure in a strained state and specific features of #beta#-#alpha# transformation in a #beta#-matrix and deformation twins on ageing. It is determined that preliminary deformation initiates the decomposition of solid solution on aging. In a metastable #beta#-titanium alloy the substructure of deformation twins is shown to vary essentially with aluminium and chromium partial substitution for molybdenum and vanadium

International Nuclear Information System (INIS)

The formation of #alpha#'-sialon using Li as a modifying cation was investigated. The effects of the Li content, firing temperatures and Si/Al ratios on #alpha#'- yield were studied. The results indicated that at lower sintering temperatures the stabilisation of #alpha#'-sialons was obtained but the high weight losses of Li at higher temperatures limited the stabilisation. Increased ''Al'' content in the compositions resulted in an increase in the stability of Li-#alpha#'-sialon at higher temperatures, by the formation of a liquid phase which retains Li in the system. (orig.).

International Nuclear Information System (INIS)

Lithium tetrachloroaluminate solutions in thionylchloride, methylacetate and their mixtures are studied by "7Li and "2"7Al NMR. It is found that introduction of methylacetate in the LiAlCl_4-SOCl_2 system results in a change of lithium tetrachloroaluminate formation constant. In the ternary system, Li"+ is solvated by methyl-acetate after complete destruction of tetrachloroaluminate anion. Refs. 9, figs. 2.

Energy Technology Data Exchange (ETDEWEB)

In this paper, aluminium nitride synthesis is carried out by direct laser irradiation onto an aluminium target surface in a nitrogen containing atmosphere. The influence of various processing parameters on the microstructure of AlN thin films is investigated in order to improve their tribological properties. The main microstructural characteristics: nature, concentration, in depth distribution and morphology of various phases are studied versus processing parameters by TEM and GIXD. (author). 2 refs., 1 fig., 2 photos.

Energy Technology Data Exchange (ETDEWEB)

In the present work, electrochemical measurements and corrosion tests in NaCl solutions were carried out to study the effect of aging treatments on pitting corrosion behavior in a 8090 alloy and its high purity Al-Li binary alloy analogue. The pitting corrosion characteristics and corrosion resistance of the 8090 alloy have been determined in relation to precipitation microstructures. (orig.).

British Library Electronic Table of Contents (United Kingdom)

In a suicide committed using aluminium phosphide (AlP) the liberated toxic phosphine gas was detected in post-mortem specimens using a headspace gas chromatographic procedure with a nitrogen-phosphorous detector (HS-GC/NPD). At autopsy a direct sampling into airtight headspace vials for a later analysis is recommended. AlP has to be considered a potent pesticide and its use and availability should be restricted as much as possible.

Energy Technology Data Exchange (ETDEWEB)

The Ti-6Al-4V alloy was treated by inductively coupled rf plasma nitriding. The effects of plasma-processing time in the range of 5-35 min on the microstructure and the mechanical properties of the plasma-nitrided Ti-6Al-4V samples were studied. The plasma power input was adjusted at 450 W and pure N{sub 2} gas was introduced to establish a treatment pressure of 8.0-8.4 x 10{sup -2} mbar. The characteristics of the nitrided layers have been investigated by microhardness testing, surface roughness measurements, optical microscopy, and x-ray diffraction. The results show that the surface microhardness increases as the plasma-processing time increases to reach 2000 HV0.1 at a plasma-processing time of 35 min. A high nitriding rate of 2.81 {mu}m{sup 2} s{sup -1} at a plasma-processing time of 25 min was achieved. The formation of the hard phases TiN, Ti{sub 2}N, and Ti(N) in the Ti-6Al-4V surfaces are found to be the reason for ...

Energy Technology Data Exchange (ETDEWEB)

Continuous-wave (cw) operation at temperatures up to 23 /sup 0/C of an Al/sub 0.26/Ga/sub 0.26/In/sub 0.48/P/Ga/sub 0.52/In/sub 0.48/P/ Al/sub 0.26/Ga/sub 0.26/In/sub 0.48/P double heterostructure (DH) laser has been achieved for the first time. The threshold current was 160 mA at 20 /sup 0/C for a device with a 10-..mu..m-wide and 250-..mu..m-long ion-implanted stripe geometry. The emission wavelength was 671 nm during cw operation at 10 /sup 0/C. To reduce thermal resistance to a heat sink, a dually stacked structure made of a thin (approx.0.3 ..mu..m) p-AlGaInP layer and a p-Al/sub 0.76/Ga/sub 0.24/As layer was used as a cladding layer. The DH wafer was grown by atmospheric pressure metalorganic chemical vapor deposition.

Energy Technology Data Exchange (ETDEWEB)

There is an increasing number of applications for hard coatings in engineering where the properties of the single-layer coating are not sufficient. One way to solve this problem is to use a multilayer coating that combines the properties of several coating materials. In this study, TiN-CrAlN and CrN-CrAlN multilayer coatings were deposited on 100Cr6 and S6-5-2 (DIN) steel substrates, by means of unbalanced magnetron sputtering. For comparison, TiN, CrN and CrAlN single-layer coatings were also prepared. For all depositions the coating temperature was below 473 K. Indentation testing, hardness measurements and scratch tests were performed to characterize the mechanical properties. The correlation between the wear behavior in rolling contact and the mechanical properties of the multilayer coatings is reported. A ball crater preparation technique through scratch tests and wear tracks was used to observe the deformation and ...

International Nuclear Information System (INIS)

MoSi_2-particulate-reinforced #alpha#-SiAlON ceramic composites 10, 20, 25, and 30 vol% were prepared by at 1,750--1,800C. The #alpha#-SiAlON matrix was of the composition (Y_0_._4_8Si_1_0_._0_0Al_2_._3_0O_1_._1_7N_1_5_._2_9). The hardness for the fully dense samples changed from HV10 = 22.5 to 15.3 GPa and the toughness from 3.2 to around 5.2 MPa#centre dot#m"1"/"2 when up to 30 vol% MoSi_2 was present. Two interesting microstructural features have been found. First, with an increasing amount of MoSi_2 a pronounced coalescence of MoSi_2 particles formed a ''dual phase'' material. The second effect was the growth of elongated #alpha#-SiAlON grains in the matrix with 10 vol% MoSi_2 added. The oxidation resistance has been determined, to be unaffected by the addition of 20 vol% MoSi_2 at 1,250 C in oxygen gas of 1 atm pressure.

Energy Technology Data Exchange (ETDEWEB)

A Fe-20at.%Cr-10%Al matrix was dispersed with a wide range of different oxides in order to study the effect of oxygen-active dopants on the high-temperature growth and adhesion of {alpha}-Al{sub 2}O{sub 3} scales. Effect of these various cation dopants on the alumina scale microstructure was correlated with dopant ion segregation to the {alpha}-Al{sub 2}O{sub 3} grain boundaries using analytical electron microscopy. Elements such as Mn and V showed little effect on the oxide scale and were not observed to segregate. Elements such as Y and Gd resulted in finer, more columnar {alpha}-Al{sub 2}O{sub 3} grains and were segregated to scale grain boundaries. However, Ti, Ta, Ca, and Nb also were found to segregate but had a lesser effect on scale morphology. This indicates that cation segregation to scale grain boundaries is not a sufficient condition to achieve beneficial oxidation effects. The driving force ...

International Nuclear Information System (INIS)

SiAlONs are ceramics with high potential as biomaterials due to their chemical stability, associated with suitable mechanical properties, such as high fracture toughness and fracture resistance. The objective of this work was to investigate the mechanical properties and the cytotoxicity of these ceramic materials. Three different compositions were prepared, using silicon nitride, aluminum nitride and a rare earth oxide mixture as starting powders, yielding Si_3N_4-SiAlON composites or pure SiAlON ceramics, after hot-pressing at 1750 deg. C, for 30 min. The sintered samples were characterized by X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM). Furthermore, hardness and fracture toughness were determined using the Vicker's indentation method. The biological compatibility was evaluated by in vitro cytotoxicity tests. Ceramic with elevated hardness, ranging between 17 and 21 GPa, and high fracture ...

CERN Document Server

A variety of investigations have demonstrated commonalities between the Baldwin (1977) Effect, the blueshifting of CIV emission lines (e.g., Gaskell 1982; Richards et al. 2002), and the L_UV-L_X relationship (e.g., Avni & Tananbaum 1982; Strateva et al. 2005; Steffen et al. 2006); indeed all three of these observational effects may be manifestations of the same underlying (but still uncertain) physics. This commonality is of interest to investigations of accretion disk winds (e.g., Murray et al. 1995; Proga et al. 2000) from active galactic nuclei (AGN) as there is evidence that broad absorption line quasars (BALQSOs) are drawn from a parent sample of quasars that exhibit larger than average CIV blueshifts, weaker than average CIV emission line strengths, and bluer than average (intrinsic) colors. The properties of the absorption troughs appear to be dependent upon these ...

Energy Technology Data Exchange (ETDEWEB)

PVD-coatings based on TiB{sub 2} are expected to show high wear resistance and low tendency of adhesion on metal forming tools. Coating adhesion and morphology can be modified over a wide range by varying the content of nitrogen (N{sub 2}) and the deposition parameters power and bias voltage. All coatings were deposited using commercial unbalanced magnetron equipment, the deposition was homogeneous in a volume of 400 x 400 x 400 mm{sup 3}. Hipped and hot pressed TiB{sub 2}-targets were used, nitrogen (N{sub 2}) was added as gas, Ti and Al by a solid Ti-Al-target. The tribological behaviour was tested by a pin-on-disc wear test. The coatings investigated were TiB{sub 2}, TiAlB(N), TiAl(N) and TiB{sub 2}/TiAl(N). As counterpart in the pin-on-disc wear test, 6 mm diameter spheres of steel (100Cr6), aluminium, brass and bronze were used. The experiments showed a non-uniform wear ...

Energy Technology Data Exchange (ETDEWEB)

Two families of CeO{sub 2}/Al{sub 2}O{sub 3} (ACE) catalyst supports, containing 3 and 20 % wt CeO{sub 2} respectively, have been examined and compared with the pure oxides CeO{sub 2} and (transition-phase) Al{sub 2}O{sub 3}. Structural data indicate that, also in the presence of CeO{sub 2}, the Al{sub 2}O{sub 3} support undergoes all phase transitions at the usual temperatures. Electron micrographs show that particles morphology and crystals size are mainly imposed by the Al{sub 2}O{sub 3} support. The porosimetric texture indicates a more pronounced meso-porosity in the ACE systems than in pure Al{sub 2}O{sub 3}, especially in the case of low CeO{sub 2} loadings. FTIR spectra and volumetric/calorimetric data of the adsorption of CO at {approx}300 K show that the surface Lewis acidity of aluminas is severely modified by the presence of CeO{sub 2}: the overall CO uptake is ...

International Nuclear Information System (INIS)

By using a model dielectric matrix in electron self-energy evaluations the computational effort of a quasiparticle band-structure calculation for a semiconductor is greatly reduced. Applications to various systems with or without inversion symmetry, having narrow or wide band gaps, and semiconductor alloys demonstrate the reliability and accuracy of the method. Calculations have been performed for thirteen semiconducting or insulating materials: Si, LiCl, AlP, AlAs, AlSb, GaP, GaAs, GaSb, InP, InAs, InSb, and the Al_0_._5Ga_0_._5As and In_0_._5_3Ga_0_._4_7As alloys. Excellent agreement with experimental results is obtained for the quasiparticle energies for these materials. The only three exceptions, E(#GAMMA#_1_c) of AlP, E(L_1_c) of AlAs, and E(L_1_c) of AlSb are discussed and attributed to various experimental uncertainties. Several other ...

International Nuclear Information System (INIS)

We use the Generalized Quasi-Chemical Approach (GQCA) combined with ab initio ultrasoft pseudopotential calculations within density functional theory in order to obtain the structural and electronic properties of Al_xGa_yIn_1_-_x_-_yX (X=As, P or N) quaternary alloys in the zincblende structure. Results for the bond lengths show that their variations with composition are approximately linear and that they do not deviate much from the values of the corresponding binary compounds. For the variation of the band gaps, we obtain a bowing parameter b=0.26 eV for the (Ga_0_._4_7In_0_._5_3As)_z(Al_0_._4_8In_0_._5_2As)_1_-_z quaternary alloy lattice matched to InP, in very good agreement with experimental data. In the case of AlGaInN, a bowing parameter of 0.22 eV is obtained for zincblende AlGaInN lattice matched to GaN. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

International Nuclear Information System (INIS)

After being pre-plated a zinc layer, an amorphous Al-Mn alloy coating was applied onto the surface of AZ31B magnesium alloy with a bath of molten salts. Then the corrosion performance of the coated magnesium alloy was examined in 3.5% NaCl solution by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The results showed that the single Zn layer was active in the test solution with a high corrosion rate while the Al-Mn alloy coating could effectively protect AZ31B magnesium alloy from corrosion in the solution. The high corrosion resistance of Al-Mn alloy coating was ascribed to an intact and stable passive film formed on the coating. The performances of the passive film on Al-Mn alloy were further investigated by Mott-Schottky curve and X-ray photoelectron spectroscopy (XPS) analysis. It was confirmed that the passive film exhibited n-type semiconducting behavior in 3.5% NaCl ...

Energy Technology Data Exchange (ETDEWEB)

Shell Solar GmbH is working on a variant of the so-called stacked elemental layer process for CIGSSe absorber production. The metal films resp. the selenium are deposited on the Mb electrode at room temperature by DC sputtering (CIG) or evaporation (Se) and then processed into semiconductors by rapid thermal annealing (RTP). Currently, the mean efficiency of the pilot plant is i 12.6 {+-} 0.2 % for non-sealed 30 x 30 cm{sup 2} modules, the key efficiency is 13.0 %. In addition to the 30 x 30 cm{sup 2} pilot line, a small series of 60x90cm2 modules was constructed in December 2004. Here, the mean efficiency was 13.0 percent while the average module power was higher than 60 W. The contribution also describes investigations of ceramically sputtered n-ZnO:Al layers with reduced Al concedntrations of 1 percent and on reactively sputtered n-ZnO.Al layers from the double roller magnetron. (orig.) [German] Bei Shell Solar GmbH wird ...

Energy Technology Data Exchange (ETDEWEB)

Two rapidly solidified powders with compositions Al-6.7 wt.% Fe-5.9 wt.% Ce and Al-6.2 wt.% Fe-5.9 wt.% Ce-1.63 wt.% Si were separated into -32 [mu]m and +32 to -63 [mu]m size fractions. Powders from both size fractions were extruded at 500 C. For comparison purposes, extrusion at a lower temperature of 400 C was also performed. In this investigation, tensile property evaluation indicated that processing of finer size fractions at high temperature offers no advantages in terms of the tensile properties but is advantageous in terms of improving the fracture toughness of alloy B. These observations underline the importance of the stability of powder microstructure during thermomechanical processing for the development of optimum mechanical properties. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Alumina-reinforced carbon nanofiber nanocomposites were prepared using different routes; powders mixture, colloidal route and sol?gel process followed by spark plasma sintering (SPS). CNFs/xAl2O3 (x = 10?50 vol.%) were prepared through nanopowders mixing in a high-energy attrition milling. The main limitations in the preparation of this kind of nanocomposites are related to the difficulty in obtaining materials with a homogeneous distribution of both phases and the different chemical nature of CNFs and Al2O3, which causes poor interaction between them. A surface coating of CNFs by wet chemical routes with an alumina precursor is proposed as a very effective way to improve the interaction between CNFs and Al2O3. An improvement of 50% in fracture strength was found for similar nanocomposite ...

Science.gov (United States)

Room-temperature continuous-wave (cw) operation of a GaInP/AlGaInP multiquantum well (MQW) laser was achieved for the first time. The threshold current was 70 mA at 22 /sup 0/C for a device with an 8-..mu..m-wide and a 250-..mu..m-long planar stripe. The emission wavelength was 668 nm. The characteristic temperature T/sub 0/ was 138 K under cw operation. The wafer with the MQW structure composed of 100-A-thick GaInP wells and 40-A-thick AlGaInP barrier layers was grown by atmospheric pressure metalorganic chemical vapor deposition.

International Nuclear Information System (INIS)

The highest equilibrium free-carrier doping concentration possible in a given material is limited by the ''pinning energy'' which shows a remarkable universal alignment in each class of semiconductors. Our first-principles total energy calculations reveal that equilibrium n -type doping is ultimately limited by the spontaneous formation of close-shell acceptor defects: the 3- -charged cation vacancy in AlN, GaN, InP, and GaAs and the 1- -charged DX center in AlAs, AlP, and GaP. This explains the alignment of the pinning energies and predicts the maximum equilibrium doping levels in different materials. (c) 2000 The American Physical Society

Energy Technology Data Exchange (ETDEWEB)

X-ray photoelectron spectroscopy measurements indicate that the Ce{sup 3+} like fraction in {gamma}-Al{sub 2}O{sub 3} supported CeO{sub 2} can be decreased by the incorporation of La{sup 3+}. If La{sup 3+} is incorporated into the {gamma}-Al{sub 2}O{sub 3} before CeO{sub 2} is added, a higher CeO{sub 2} dispersion and a greater range of reversible reducibility of the CeO{sub 2} may also be obtained. These changes offer potential for improvement in the oxygen storage capacity provided by CeO{sub 2} in three-way catalysts. The actual effect of La{sup 3+} incorporation on the activity and durability of a Pt catalyst is assessed by a combination of temperature programmed reduction and flow reactor measurements.

Energy Technology Data Exchange (ETDEWEB)

The present conference discusses plasma-assisted surface coating/modification processes, the applications to date of ion nitriding, the effects of nitrogen on metal surfaces, ion nitriding mechanisms in Cr, Al and Cr + Al-containing 1040 steel, ion nitriding of Al and its alloys, life enhancement for forging dies, novel anode plasma nitriding developments, and a comparative study of the pulsed and dc ion-nitriding behavior in specimens with blind holes. Also discussed are the influence of heating method on ion nitriding, surface hardening of marage steels by ion nitriding without core hardness reduction, plasma nitriding of nodular cast iron sput gears, NbN composites for superconductors, the carburization of tungsten in a glow discharge methane plasma, economic considerations concerning plasma nitriding, and the corrosion properties obtained by ion nitriding.

Energy Technology Data Exchange (ETDEWEB)

This is the first interdisciplinary approach to urban water and waste water managment. The author presents the knowledge acquired during the project. [German] Die ganzheitliche Betrachtung der Wasserwirtschaft in urbanen Gebieten ist sowohl in der Forschung als auch in der Praxis neu. Zwischen der Bearbeitung eines Forschungsprojektes und eines Ingenieurprojektes gibt es grundsaetzliche Differenzen, trotzdem sind wir der Meinung, dass es bezueglich der interdisziplinaeren Aspekte und der ganzheitlichen Betrachtung der Wasserwirtschaft sowohl in der Forschung als auch in der Praxis aehnliche Probleme gibt. Aus diesem Grunde wird in dieser Arbeit versucht ueber einige Erfahrungen aus dem interdisziplinaeren und ganzheitlichen Forschungsprojekt zu berichten. (orig.)

International Nuclear Information System (INIS)

The powder particle size, D, influences the creep behaviour of Al-Cr-Zr alloys. The alloy studied in this work, Al-5Cr-2Zr (mass%), was prepared by argon atomization. Three size fractions of powder particles were selected: 24-50 #mu#m, 50-100#mu#m and 100-200 #mu#m in diameter. They were consolidated by extrusion. Independently of D, the flow behaviour of the alloy can be described by the power law equation. As test temperature increases, the stress exponent n decreases up to a value close to 5. A decrease of D causes an increase of n and delays the alloy degradation at high temperature. (Author) 11 refs.

International Nuclear Information System (INIS)

The authors discuss several aspects of defect formation in epitax heterostructures based on solid solutions of A"3B"5 semiconductor compounds; these heterstructures were prepared by liquid phase epitaxy by cooling suitable high-temperature solutions from the initial growth temperature. An analysis shows that the regions near heterojunctions are regions of increased defect density even in compositions based on Al /SUB x/ Ga /SUB 1-x/ As-GaAs, Al /SUB x/ Ga /SUB 1-x/ P-GaP, Al /SUB x/ Ga /SUB 1-x/ Sb-GaSb, where the differences in lattice parameters of the contacting materials are a minimum.

Science.gov (United States)

Combined electron, photon, and intense UV irradiation tests have been carried out on three mirror designs, (Si, Al/sub 2/O/sub 3/)/sub 2/Ag, (Si, SiOx)nAg, and (ZnS, Al/sub 2/O/sub 3/)4Ag, to investigate their suitability for space-borne chemical laser applications. It is found that the (Si, oxide)nAg enhanced-reflectance design is a viable candidate for such applications, whereas ZnS, in combination with either ThF/sub 4/ or Al/sub 2/O/sub 3/, shows unacceptably high absorption increases at the 2.8-micron HF laser wavelength with irradiation. It is pointed out, however, that further experiments are needed to fully understand the effect of irradiation on the (Si, oxide)nAg enhanced-reflectance mirrors.

Energy Technology Data Exchange (ETDEWEB)

MCrAlY coatings are widely used on hot section components of gas turbines to provide hot corrosion and/or oxidation protection by formation of an oxide layer on the surface. As the protective oxide scale exfoliates during service, aluminum from the coating diffuses outward for reformation of the protective scale. Aluminum may also diffuse inward due to the differences in composition between the coating and the substrate. Thus, the coatings degrade due to oxidation, oxide scale spallation, and inward and outward diffusion of aluminum. Service life of these coatings is controlled by the aluminum content in the coating, operating temperature and start- shutdown cycles. In-service degradation of CoCrAlY and CoNiCrAlY coatings is presented. A procedure to predict the remaining service life of coatings under oxidizing conditions is discussed. (orig.) 12 refs.

International Nuclear Information System (INIS)

It is generally known that a number of metallic glasses have excellent corrosion resistance in a variety of chemically hostile environments. Consequently, the use of laser cladding to coat a massive crystalline material such as aluminium with a layer of a metallic glass has obvious advantages. In this paper, the authors will show that the formation of a predominantly amorphous layer of Zr_6_0Al_1_5NI_2_5 alloy by laser processing is possible, if the obstacles to amorphization are overcome. In addition, evidence of the excellent corrosion resistance of this alloy in a NaCl solution will be given. A comparative study of the corrosion behavior of this amorphous alloy with pure aluminium and Al-Cr alloy will be done, in order to complete previous studies of laser processed coatings of aluminum substrates.

British Library Electronic Table of Contents (United Kingdom)

This paper presents a patient specific deformable heart model that involves the known electrical and mechanical properties of the cardiac cells and tissue. The whole heart model comprises ten Tusscher's ventricular and Nygren's atrial cell models, the anatomical and electrophysiological model descriptions of the atria (introduced by Harrild et al.) and ventricle (given by Winslow et al.), and the mechanical model of the periodical cardiac contraction and resting phenomena proposed by Moireau et al. During the propagation of the depolarization wave, the kinetic, compositional and rotational anisotropy is handled by the tissue, organ and torso model. The applied patient specific parameters were determined by an evolutionary computation method. An intensive parameter reduction was performed u...

International Nuclear Information System (INIS)

Red mud (RM) is the main by-product of the Bayer process for alumina extraction from bauxite, and grey slurries (GS) are generated during the granite rocks transformation processes. the huge volume of those wastes generated every year suppose a serious environmental problem. Recent works by our group demonstrate the efficiency of both types of muds as corrosion inhibitors for iron and steel in alkaline media containing chlorides. The elemental analysis of these slurried shows that Al"3+ is the main common element. Therefore, the aim of this paper is to study the effect of the soluble Al"3+ in the electrochemical behaviour of iron in alkaline media, in presence and absence of chlorides. The electrochemical study using Cyclic Voltammetry (CV) and Electrochemical Impedance Spectroscopy (EIS) together with surface analysis techniques allowed to conclude that Al"3+ blocks the surface of steel in alkaline media chloride ...

Science.gov (United States)

... al - 3.9863 a 2 - 508929.2 a3 - 288.994 a4 - 68.129 13. It is apparent from Figure I and Equation 1 that when water temper- ...

International Nuclear Information System (INIS)

In this letter a method to estimate the visco-elastic response of monolithic ceramics to cyclic loading conditions at high temperatures is proposed. A relation is observed between the visco-elastic energy dissipation measured for two silicon nitride materials, and the structural characteristics of their respective intergranular phases. Some consequences for the fatigue resistance of the tested materials, and of non-transforming monolithic ceramics in general, are discussed. Two batches (G for glassy and C for crystalline) of SiAlON have been studied. The G-batch is obtained by pressureless sintering of silicon nitride powder with Y_2O_3 (6 wt%) and 6AlN-SiO_2 (5 wt%) as sintering additives. The main phase after sintering is #beta#-sialon. Upon cooling from the sintering temperature the amorphous intergranular residues of the sintering additives and of SiO_2, which is unavoidably present as a thin layer on the silicon nitride powder, crystallize ...

International Nuclear Information System (INIS)

AlGaInP epitaxial layers grown at 690 degree C by atmospheric pressure organometallic vapor phase epitaxy are investigated by transmission electron microscopy. For the first time, compositionally modulated and ordered structures are simultaneously observed in AlGaInP alloys. The ordering is of the CuPt type with ordering along the #left brace#111#right brace# directions. The ordered regions appear as plate-like microdomains, while the composition modulation takes the form of a fine columnar constrast oriented along the growth direction. In addition, from the results of (001) plan-view diffraction contrast examination, the principal strain direction associated with the modulation structures is found to be perpendicular to the growth direction and lies in the surface plane. Thus, it is concluded that the spinodal decomposition is initiated and developed on the surface during the growth of the AlGaInP epitaxial layers and, ...

Energy Technology Data Exchange (ETDEWEB)

In this work a comprehensive metallophysical study was carried out for two aluminosilicide slip coatings of the systems Al-Si and Al-Nb-Si and an electron-beam Co-Cr-Al-Y coating on alloy EP-539 (17...19% Cr, 4...6% Co, 2.5...4% W, 4.5...6.5% Mo, 2...3% Ti, 3...4% Al, 1.4...2% Nb, balance Ni) after high-temperature testing. The protective properties of the coatings were evaluated from the results of laboratory tests for heat resistance at 1000/sup 0/C in the combustion products of diesel fuel with added sulfur at 970, 1000, and 1060/sup 0/C for 100 h and after full-scale tests for 150, 250, 400, and 700 h. Metallographic, hardness, x-ray, and micro x-ray studies of the coating were carried out. Layer-by-layer phase composition and the lattice spacing of the main phases were determined. X-ray analysis was carried out in an a DRON-1 diffractometer in copper K/sub ..-->../-radiation, and x-ray ...

Science.gov (United States)

Este sistema de informacion provee al usuarion con un listado de areas protegidas argentinas ordenado por nombre, por provincia, ... ...

Science.gov (United States)

Washington, DC -07/24/09 Photo: Secretary Clinton and Iraqi Prime Minister al-Maliki at HCC Bilateral; Washington, DC -07/24/09 Photo: Secretary Clinton at Joint Press...

International Nuclear Information System (INIS)

The optical properties of divalent europium activated Ca-#alpha#-SiAlON were investigated and the excitation and emission processes were discussed. The emission wavelength is influenced by the activator concentration of Eu more than the codopant concentration of Ca, in case of the same matrix composition of #alpha#-SiAlON. The red-shift of emission increases when the concentration of Eu increases. In addition, it was revealed that the red-shift of emission would be caused by the construction of the package of optical device. The correlated color temperature becomes low by the red-shift for the white light-emitting diode (LED) lamp using Ca-#alpha#-SiAlON:Eu phosphor when the phosphor powder concentration increases in the transparent resin which coats the primary light source of a blue LED die. The additional red-shift can be observed when the excessive amount of phosphor coating is intentionally poured to the white LED ...

Science.gov (United States)

Studies were assigned values based on whether they were anecdotal or ... or family income), work experience, birth order, military or civilian ...... observed with submarine personnel and polar expeditioners (Sandal et al., 1996). ...

UK PubMed Central (United Kingdom)

Listeners use lipread information to adjust the phonetic boundary between two speech categories (phonetic recalibration, Bertelson et al. 2003). Here, we examined...Full Text Available

Science.gov (United States)

... al. (1992) and Santos and Bueno (2002) in Scylla serrata and Cal. ornatus, respectively. According to these authors, ... S. Poovachiranon. 1992. Age of the mangrove crab Scylla serrata at colonization by ...

UK PubMed Central (United Kingdom)

Klebsiella oxytoca can use nitrate and nitrite as sole nitrogen sources. The enzymes required for nitrate and nitrite assimilation are encoded by the nasFEDCBA operon....Full Text Available

International Nuclear Information System (INIS)

This paper presents the first results on formation and study of structure and properties of micro- and nanocomposite combined coatings. By means of modeling the deposition processes (deposition conditions, current density-discharge, plasma composition and density, voltage) we formed the three-layer nanocomposite coatings of Ti-Al-N/Ti-N/Al_2O_3. The coating composition, structure and properties were studied using physical and nuclear-physical methods. The Rutherford proton and helium ion backscattering, scanning electron microscopy with microanalysis, grazing incidence X-ray diffraction, as well as nanohardness tests (hardness) were used. Measurements of wear resistance and corrosion resistance in NaCl, HCl and H_2SO_4 solutions were also performed. For testing mechanical properties such characteristics of layered structures as hardness H, elastic modulus E: H"3/E"2 etc. were measured. It is demonstrated that the formed three-layer nanocomposite coatings have ...

International Nuclear Information System (INIS)

Nanocrystalline Fe75Si20M5 (M = Al, B and Cr) powders were synthesized by mechanical alloying in a planetary ball mill from high purity elemental powders. Evolution of non-equilibrium solid solutions of ?-Fe[Si,(Al, B, Cr)] with a nanocrystalline structure was accompanied by the introduction of a large number of dislocation defects in the course of the milling process. Fe sites get substituted by Si and M (M = Al, B, Cr) atoms during the milling process. The structural change and the resulting disorder are reflected in the changes in the lattice parameter and average magnetic moment of the powders milled for various time periods. The effective magnetic anisotropy increases linearly with the milling time. An increase in coercivity with increasing milling time was observed which could be attributed to the introduction of dislocations and the reduction in the powder particle size during milling. The presence of dislocations ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

In the IEEE Marine Technology Society OCEANS 2009 Conference, Biloxi. October 26-29, 2009. Biloxi, MS. Al-Hamdan, M.; Estes, M.; Quattrochi, D.; Thom, R.; ...

Science.gov (United States)

J. Edmunson, BAE Systems/NASA Marshall Space Flight Center (320 Sparkman Drive. VP61, Huntsville AL 35805, Jennifer.E.Edmunson@nasa.gov). ...

Energy Technology Data Exchange (ETDEWEB)

The electrical conductivity of Vitox-alumina (99.2%), Wesgo-alumina (99.9%) and AlN (99.6%) has been measured during and after irradiation with an experimental set-up which allows fusion relevant loading conditions. All irradiations were performed in high vacuum at 450 C using a 104 MeV {alpha}-particle beam with an applied DC electric field of 100 kV/m. In the high purity Vitox-alumina the in-situ and postirradiation bulk conductivities {sigma} and {sigma}{sub 0} show the highest irradiation induced electrical breakdown ever observed. The saturation level near 4 x 10{sup -2} ({Omega}m){sup -1}, reached already after 0.015 dpa (O-sublattice), is already above the critical value necessary to avoid MHD pressure drop with 10 {mu}m coatings in flowing liquid metal coolants. Under the same conditions no radiation induced electrical degradation at all has been found in Wesgo-alumina and AlN. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Al{sub x}Ga{sub 1{minus}x}P layers (0 {le} x {le} 0.7), with thicknesses of {ge}1 {micro}m were grown on Si (100) wafers by metal-organic molecular beam epitaxy (MOMBE) at 450 C. Transmission electron micrographs of the single crystal films revealed that the microstructure contains stacking faults and microtwins especially near the interface as well as both threading and misfit dislocations. Hardness and elastic modulus were measured using a Nanotest 500 indenter, which can probe the film properties without influence from the substrate. The hardness H varies linearly according to (11.8 {minus} 2.3x) GPa. The absence of alloy hardening is due to the fact that there is no difference in atomic size of Al and Ga. The indentation modulus E/(1{minus}v{sup 2}) decreases monotonically from 136 GPa for GaP to 129 GPa for Al{sub 0.7}Ga{sub 0.3}P and bows only slightly (about 2%) below the straight line of linear interpolation.

Science.gov (United States)

Aug 25, 2004 ... Current Developments in Future Planetary Probe Sensors: .... Data: Outgoing and incoming EIA RS-422 interface for serial data transmission (for electrical purposes only, .... Milos, et. al, Journal of Spacecraft & Rockets 1999 ...

Science.gov (United States)

The catalytic effects of copper-aluminium-magnesium oxides in the oxidative coupling of phenylethyne is described. The importance of surface properties as a redox site are discussed.

Energy Technology Data Exchange (ETDEWEB)

Scientists have just taken a big step toward understanding the cause of Lou Gehrig's disease, one of the most devastating nerve degenerative diseases. A large team of researchers, led by Robert Brown Jr. of Harvards's Massachusetts General Hospital and Robert Horvitz, a Howard Hughes Medical Institute investigator at the Massachusetts Institute of Technology, report in the 4 March Nature that they've identified the gene that causes a hereditary form of the condition, which also goes by the name amyothophic lateral sclerosis (ALS). While most ALS cases - approximately 90% - are apparently sporadic' and not caused by an inherited gene defect, all the patients have such similar symptons that researchers are hopeful that what they learn about hereditary ALS will also apply to the sporadic form, possibly leading to new therapeutic strategies that will help both. It's a very important ...

International Nuclear Information System (INIS)

Temporal developments of the photoluminescence (PL) intensity at temperatures of 7, 100, and 294 K are analyzed using the rate equations including the exciton dissociation and association terms for an Al_0_._5_3In_0_._4_7P/Ga_0_._5_2In_0_._4_8P/Al_0_._5_3In_0_._4_7P-quantum well structure. At 7 K, the nonexponential time dependence of the PL intensity is caused by the exciton dissociation process. At 7 and 100 K, PL intensity is dominated by the exciton recombination even if the exciton density is smaller than the dissociated carrier density. The thermally excited background carriers affect the recombination processes at 100 and 294 K. At 294 K, the rise part of the PL intensity is dominated by the exciton recombination, though the dissociated carrier density dominates. [copyright] 2001 American Institute of Physics.

British Library Electronic Table of Contents (United Kingdom)

In the present study, new light weight nano-composites (AZ31B-3.3Al2O3-Cu) based on magnesium alloy AZ31B are developed using disintegrated melt deposition technique. Microstructural characterization studies revealed grain refinement and significant increase in amount of second phases as a result of increasing presence of copper. All the samples exhibited minimal porosity and good matrix-second phase interfacial integrity. The results also showed that addition of both nano-Al2O3 and Cu led to a simultaneous improvement in 0.2% yield compressive strength (0.2%YCS), ultimate compressive strength (UCS) and work of fracture (WoF) of the AZ31B magnesium alloy while failure strain was marginally affected. The results of this study clearly illustrate the capability of AZ31B-Al2O3-Cu formulations ...

British Library Electronic Table of Contents (United Kingdom)

Phosphor material BaAl2O4:Eu2+, Dy3+ with varying compositions of Sr substitution were prepared by the solid-state synthesis method. The phosphor compositions were characterized for their phase and crystallinity by XRD, SEM and TEM. Photoluminescence (PL) properties were investigated measuring PL and decay time for varying Ba/Sr compositions. The PL results show the blue shift in the luminescence properties in Sr substituted BaAl2O4:Eu2+, Dy3+ compared to parent BaAl2O4:Eu2+, Dy3+. It is probably due to the influence of 5d electron states of Eu2+ in the crystal field because of atomic size variation causing crystal defects. Dy3+ ion doping in the phosphor generates deep traps, which results in long afterglow phosphorescence.

Energy Technology Data Exchange (ETDEWEB)

A Comment on the Letter by M. C. Green et al., Phys. Rev. Lett. 53, 1893 (1984).

Science.gov (United States)

de que usted y sus hijos tengan todas las vacunas contra el tétanos. Heridas en una pierna cubiertas con curitas estériles ¿Está su hijo al día con las vacunas? Revise la...

Wastenet

Heidelberg: Springer-Verlag. ABRAHART, R.J., SEE, L.& DAWSON, C. ...Water Science and Technology Library: Springer. AL-AHMADI, K., HEPPENSTALL, A.J., ...Springer. BIRKIN, M.H., TURNER, A., WU, B.

UK PubMed Central (United Kingdom)

Lovatt et al. (1979 Plant Physiol 64: 562-569) have previously demonstrated that end-product inhibition functions as a mechanism regulating the activity of the orotic acid pathway in...Full Text Available

International Nuclear Information System (INIS)

The data are analyzed on cumulative antiproton production on Be, Al, Cu, and Ta nuclei induced by 10 GeV protons. The analysis is carried out in the framework of the flucton quark fragmentation model.

Energy Technology Data Exchange (ETDEWEB)

The properties and low pressure organometallic vapor phase epitaxy of Ga{sub x}In{sub 1{minus}x}P/(AlGa){sub 0.5}In{sub 0.5}P quantum well (QW) laser diode heterostructures with Al{sub 0.5}In{sub 0.5}P cladding layers, and having wavelength 614 < {lambda} < 690 nm, are described. At longer wavelengths ({lambda} > 660 nm), threshold current densities under 200 A/cm{sup 2} and efficiencies greater than 75% result from a biaxially-compressed GaInP QW active region. Although short wavelength laser performance is diminished by the poor electron confinement afforded by AlGaInP heterostructures, good 630 nm band performance, and extension into the 610 nm band, is achieved with strained, single QW active regions.

Science.gov (United States)

picture will download the highest resolution version available. M51: X-Rays from the Whirlpool Credit: A. Wilson (UMD) et al., CXC, NASA Explanation: Fresh from yesterday's...

Science.gov (United States)

Wood, R. A.; and Ogden, H. R.: The All-Beta Titanium Alloy (Ti-13V-llCr-3Al). DMIC Rept. 110 (ASTIA AD 214002), Battelle Mem. Inst., Apr. 17, 1959. 22. White ...

UK PubMed Central (United Kingdom)

BackgroundPathophysiological mechanisms involved in amyotrophic lateral sclerosis (ALS) are complex and none has identified reliable markers useful in routine patient evaluation....Full Text Available

Science.gov (United States)

The authors have presented results of an investigation of wettability of SiC particulates by liquid alloys of the Al-Si-Mg system. The evaluation of wetting has been carried out through the determination of the threshold pressure for infiltration of packed SiC particulates by the liquid alloy. The results indicate that whereas Si and Mg additions do not affect wetting, in the case of the ternary alloys the contact angle decreases in an amount proportional to the content of Mg[sub 2]Si.

Energy Technology Data Exchange (ETDEWEB)

The batchwise preparation of molecular sieves for methanol conversion shows some inconsistency in catalytic stability. This is a result mainly of the change of SiO/SUB/2/Al/SUB/2O/SUB/3 in ion exchange to an H-type sieve. The dealumination during ion exchange depends upon crystal size and structural factors, which can be characterised by the cyclohexane adsorption of the raw molecular sieve. A high SiO/SUB/2/Al/SUB/2O/SUB/3 H-molecular sieve can be prepared from a molecular sieve of high adsorption capacity, this leading to a catalyst of higher stability. (4 refs.)

International Nuclear Information System (INIS)

High temperature deformation behavior of an alpha + beta titanium alloy Ti-3Al-4V has been investigated at 910 deg. C. by using the method of cross head speed cycling. On the basis of flow stress, strain rate and strain rate sensitivity data, the alloy was found to exhibit strain hardening at this temperature which resulted in degradation in superplastic properties of the alloy. A high beta-phase volume fraction and grain-growth in both alpha and beta phases were considered responsible for the observed hardening effect. (author)

International Nuclear Information System (INIS)

SP-700, an emerging #beta#-rich #alpha#+#beta# titanium alloy, is designed to improve superplastic formability as well as mechanical properties over Ti-6Al-4V alloy. Owing to its fine microstructure and low #beta#-transus temperature, it is superplastic-formable at temperature below 1,073K (800 C) with low flow stress. Remarkable workability of this alloy is also retained in conventional Manufacturing processes. Another advantage of SP-700 is heat treatment response which includes deep hardenability and quick aging kinetics. Corrosion resistance and machinability are equivalent to or better than Ti-6Al-4V alloy.

Energy Technology Data Exchange (ETDEWEB)

A study was made on the effect of 3.5 MeV electron irradiation on the properties of light-emissive structure based on GaAlAs. It is shown that a considerable decrease in the emitted light intensity as a result of electron irradiation not accompanied by changes in recombination- and electric properties of the mentioned structures. It is established by the electron-microscopy and Auger-spectroscopy meazurements that electron irradiation causes the occurrence of regions of free aluminium clusters on the external surface of the structure n-layer. The number and the sizes of the regions depend on the electron doze. It was assumed that the mentioned regions can play a role of attenuation filter for the light emitted by the structure.