International Nuclear Information System (INIS)

Interfacial tension at the aqueous solution of di-2-ethylhexylphosphoric acid or its copper salts/water solutions has been measured by the drop volume method.

Energy Technology Data Exchange (ETDEWEB)

The crystallization of calcium sulfate from aqueous solutions with NaCl is both geological and industrial interest because NaCl is the dominant solute in natural brines and many industrial fluids. Induction periods for the nucleation of calcium sulfate dihydrate were experimentally determined as a function of supersaturation in NaCl solutions from 0 to 6 m at 25 C and in 3.0-m NaCl solutions at temperatures from 25 to 90 C. Using classic nucleation theory, the interfacial tension between gypsum and 3.0-m NaCl solution was estimated to be about 39 mJ/m[sup 2] at 25 C and increases with increasing temperature (to 63 mJ/m[sup 2] at 90 C). It was observed that the induction period decreases with increasing NaCl concentrations up to 3 m and then starts to increase slightly at a given temperature and saturation state. The electrolyte effect on nucleation was proportional to the enhanced solubility of calcium sulfate dihydrate in NaCl solutions. This ...

CERN Document Server

A Langmuir film is a molecularly thin film on the surface of a fluid; we study the evolution of a Langmuir film with two co-existing fluid phases driven by an inter-phase line tension and damped by the viscous drag of the underlying subfluid. Experimentally, we study an 8CB Langmuir film via digitally-imaged Brewster Angle Microscopy (BAM) in a four-roll mill setup which applies a transient strain and images the response. When a compact domain is stretched by the imposed strain, it first assumes a bola shape with two tear-drop shaped reservoirs connected by a thin tether which then slowly relaxes to a circular domain which minimizes the interfacial energy of the system. We process the digital images of the experiment to extract the domain shapes. We then use one of these shapes as an initial condition for the numerical solution of a boundary-integral model of the underlying hydrodynamics and compare the subsequent images of the experiment to ...

Energy Technology Data Exchange (ETDEWEB)

In the near well-bore region and perforations, petroleum fluids usually flow at high velocities and may exhibit non-Darcy-flow behavior. Microorganisms can increase permeability and porosity by removing paraffin or asphaltene accumulations. They can also reduce interfacial tension by producing biosurfactants. These changes can significantly affect non-Darcy flow behavior. Theoretical analysis shows that microbial activities can enhance production by decreasing the turbulence pressure drop and in some cases increasing the drag force exerted to the oil phase. This implies that the effects of microbial activities on non-Darcy flow are important and should be considered in the evaluation of microbial well stimulation and enhanced oil recovery.

Energy Technology Data Exchange (ETDEWEB)

The kinetics of calcium sulfate crystal growth is of importance in various fields, such as geochemistry, desalination technology, petroleum industry, and water and wastewater treatment. The seeded crystal growth rate of calcium sulfate dihydrate was measured as a function of supersaturation in NaCl electrolyte solutions from 0 to 6 m at temperatures of 25, 50, 70, and 90 C. The growth followed a second-order parabolic rate law with activation energies greater than 53 kJ/mol which suggested the surface reaction as the rate-limiting step. It was observed that the rate constant and the activation energy are solution composition dependent. The rate constant increases with NaCl concentration up to 3 molal and then begins to fall slightly. The activation energy dropped from 61 kJ/mol in the pure Ca-SO[sub 4]H[sub 2]O system to 53 kJ/mol in 3.0 m NaCl solutions. The electrolyte effect was similar to the crystal solubility behavior in aqueous electrolyte solutions resulting from the variation ...

CERN Document Server

Preparation of covalently modified organic-inorganic composite nanoparticles and their interfacial electron transfer researches

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A three-dimensional, three-phase, multiple-component numerical simulator was developed to investigate transport and growth of microorganisms in porous media and the impacts of microbial activities on oil recovery. The microbial activities modeled in this study included: (1) growth, retention, chemotaxis, and end product inhibition of growth, (2) the formation of metabolic products, and (3) the consumption of nutrients. Major mechanisms for microbial enhanced oil recovery (MEOR) processes were modeled as follows: (1) improvement in sweep efficiency of a displacement process due to in situ plugging of highly-permeable production zones by cell mass or due to improved mobility control achieved by increasing the viscosity of the displacing fluid with a biopolymer, and (2) solubilization and mobilization of residual oil in porous media due to the reduction of the interfacial tension between oleic and aqueous phases by the production of a ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The interfacial area transport equation dynamically models two-phase flow regime transitions and predicts continuous changes of the interfacial area concentration along the flow field. It replaces the flow regime-dependent correlations for the interfacial area concentration in thermal-hydraulic system analysis. In the present study, detailed formulation of the interfacial area transport equation is presented along with its evaluation results based on the detailed benchmark experiments. In view of model evaluation, the equation is simplified into one-dimensional steady state one-group interfacial area transport equation. The prediction made by model agrees well with the experimental data obtained in round pipes of various diameters. The framework for the two-group transport equation and the necessary constitutive relations are also presented in view of bubble transport of various ...

UK PubMed Central (United Kingdom)

OBJECTIVES: Although the tricyclic antidepressant amitriptyline is extensively used in the prophylactic treatment of chronic tension-type headache, only few studies have investigated the efficacy of...Full Text Available

Science.gov (United States)

... energy absorption characteristics of composite sandwich panels, thermoplastic energy-absorbing subfloor structures, and shoulder belt pre- tensioners. ...

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

The behavior and properties of associated bodies were studied through measurement of surface tension considering acetone-soluble fraction relatively light among various solvent extracts of coal. In experiment, the acetone-soluble fraction was extracted from the substances extracted from Upper Freeport coal as standard specimen using the mixed solvent of carbon disulfide (CS2) and N-methyl-2-pyrrolidinone (NMP), and it was dissolved into NMP after drying. Surface tension was measured by Wilhelmy method. The experimental results are as follows. Equilibrium surface tension is equal to the surface tension of pure solvent in a low concentration range of solution, and decreases with an increase in concentration approaching a fixed value at 0 in log concentration, nearly showing an S curve. Adsorption of species with non-polar aromatic ring of the acetone-soluble fraction on a solution surface probably ...

Energy Technology Data Exchange (ETDEWEB)

Experimental investigations have been conducted to determine two-phase natural circulation interfacial parameters by real-time neutron radiography. The natural circulation loop used in the present experiments consists of a vertical two-phase section, a gas liquid separator, and a gas injection/heating section. Experiments were performed in a neutron beam for visualization using realtime neutron radiography system. The natural circulation was initiated by injection of known gas flow rate in the heated section. Two-phase flow interfacial parameters including interfacial geometry and phase velocities etc. for bubbly flow and slug flow patterns observed in the experiments will be given in detail. The results indicate that while the natural circulation is largely as expected and that steady stable flows are possible, there are some local phenomena that introduce instabilities due to the interfacial phenomena ...

Energy Technology Data Exchange (ETDEWEB)

The NREL Sensitized Solar Cell (SSC) Core Program supports the Solar America Initiative by: (1) targeting new devices and processes for commercialization by 2015 that are less expensive, more efficient, highly reliable, and environmentally benign; (2) collaborating with DOE OS/BES to conduct basic research targeting breakthroughs in key areas, such as ultra-high efficiency and/or ultra-low cost materials and devices.

Science.gov (United States)

corrosi6n bajo tensiones en las aleaciones de aluminio empleadas ei aircraft are discussed, giving attention to engine problems, hydraulic ...

Energy Technology Data Exchange (ETDEWEB)

FLOWTRAN-TF is a new two-component, two-phase thermal-hydraulics code to capture the detailed assembly behavior associated with loss-of-coolant accident analyses in multichannel assemblies of the SRS reactors. The local interfacial area of the two-phase mixture is computed by summing the interfacial areas contributed by each of three flow regimes. For smooth flow regime transitions, the code uses an interpolation technique in terms of component void fraction for each basic flow regime.

International Nuclear Information System (INIS)

Potassium atoms in selected high-lying np Rydberg states (80 #<=# n #<=# 400) are being used as a tool to examine electron-polar molecule collisions at ultra-low energies (#approx#80 #mu#eV - 1 meV). This energy regime has not been investigated previously and is of interest because the corresponding electron de Broglie wavelength is large, #approx#1300 - 330 Angstrom, and because the collision time is comparable to the period of molecular rotation. A variety of target molecules has been studied, including simple rotors such as HF, and more complex species such as NH_3, CH_3I, CH_2Br_2 and C_6H_5NO_2. These targets encompass a range of dipole moments and rotational behavior, but analysis of the data shows that in each case the cross section #sigma#(#epsilon#) for rotationally-inelastic electron-polar molecule scattering varies approximately as 1/#epsilon# where #epsilon# is the electron energy. Such threshold behavior is not predicted by the Born approximation ...

International Nuclear Information System (INIS)

Studies of destruction of very-high-n (100ultralow electron energies (#approx#80 #mu#eV--1.4 meV), the cross section #sigma#(var-epsilon) for rotationally inelastic scattering of electrons by a polar target varies approximately as 1/var-epsilon, where var-epsilon is the electron energy.

Science.gov (United States)

Understanding the influence of interfacial structures on the nanoarchitecture mechanical properties is of particular importance for its mechanical applications. Due to a small size of constituting nanostructural units and a consequently high volume ratio of such interfacial regions, this question becomes crucial for the overall mechanical performance. Boron nitride bamboo-like nanotubes, called hereafter boron nitride nanobamboos (BNNBs), are composed of short BN nanotubular segments with specific interfaces at the bamboo-shaped joints. In this work, the mechanical properties of such structures are investigated by using direct in situ transmission electron microscopy tensile tests and molecular dynamics simulations. The mechanical properties and deformation behaviors are correlated with the interfacial structure under atomic resolution, and a geometry strengthening effect is clearly demonstrated. Due to the interlocked ...

International Nuclear Information System (INIS)

Research highlights: ? Reports a high protection system for the alloy in corrosive environment. ? Describes an interfacial process with self-healing properties. ? Reports the influence of substrate pre-treatment in the coating performance. - Abstract: In this paper the interface of poly(vinylidene fluoride) coatings prepared by the dip coating method and HF-treated AZ31 magnesium alloy was evaluated. The best performance of this system in corrosion tests compared to ground, as-received and acetic acid cleaned substrates is related to an acid-base interaction at the interface and to interfacial reactions which resulted in a self-healing process. The protectiveness of the samples was investigated using impedance and immersion tests while the coating morphology and interface stability were investigated by scanning electron microscopy, X-ray photoelectron spectroscopy and adhesion tests.

Energy Technology Data Exchange (ETDEWEB)

Considerable interest has focused recently on the use of lignocellulosic fibers as a reinforcement for thermoplastic polymers. The combination of these dissimilar materials, however, is characterized by a widespread incompatibility that leads to a weak fiber/polymer interface and poor performance properties for the composite. In an effort to improve compatibility a number of fiber surface modification approaches have been investigated including plasma, ozone, and polymer grafting treatments. Evaluation of adhesion improvements has been complicated by processing variables that are difficult to control. This paper will discuss the use of the-micro-debond test in quantifying the interfacial shear strength (ISS) in wood fiber/polystyrene composites. Wood fibers were modified to different degrees with styrene-maleic anhydride copolymers that varied in their composition. The effect of fiber modification on surface energetics was determined using dynamic contact angle ...

UK PubMed Central (United Kingdom)

Midurethral tension-free sling procedure has become one of the most popular techniques for the treatment of stress urinary incontinence. As the time elapsed, however, complications associated with a...Full Text Available

UK PubMed Central (United Kingdom)

1. In rat soleus muscle, high frequency electrical stimulation produced a rapid increase in intracellular Na+ (Na+i) content. This was considerably larger in muscles contracting without developing tension...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundThoracic injuries play an important role in major trauma patients due to their high incidence and critical relevance. A serious consequence of thoracic trauma is pneumothorax,...Full Text Available

UK PubMed Central (United Kingdom)

Laboratory studies investigated the influence of dissolved oxygen tension (DOT) on microbial degradation of hexadecane in cultures with sediment-seawater suspensions. With a fermentor system, it was...Full Text Available

UK PubMed Central (United Kingdom)

OBJECTIVES: The ability to maximally generate active muscle tension during resistance training has been established to be a primary determinant for strength development. The influence of intrasession...Full Text Available

UK PubMed Central (United Kingdom)

The hierarchical arrangement of collagen and mineral into bone tissue presumabley maximizes fracture resistance with respect to the predominant strain mode in bone. Thus, the ability of cortical...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

It is postulated that a break of a thin-walled pipe does not cause a subsequent break in the pipe in the vicinity of a plastic hinge even when the wall is weakened by a 60 circumferential crack of a depth of 30% of the wall thickness on the tension side. This pipe behavior is the result of plastic buckling in the compression side and applies to pipes of diameter-to-thickness ratio larger than 20. For this type of pipe, the axial strains decrease with increasing diameter-to-thickness ratio in the tension side. As the pipe is only loaded in one direction, there is no cyclic behavior that can trigger a subsequent break. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This is the introductory paper for eight papers that follow in this issue of Natural Resources Journal that were presented at a symposium on the titled subject. The editor notes that two movements in recent decades have been identified with coastal regions - efforts to conserve natural resources and energy source development - and that profound social, economic, and political ramifications have attended these movements. He further notes that the tensions and demands created by the above two developments proved too much for state and local mechanisms, eventually culminating in the Coastal Zone Management Act of 1972. He then briefly evaluates the focus and success of CZMA and reviews the other papers. 58 references.

International Nuclear Information System (INIS)

Accelerator mass spectrometry (AMS) represents a powerful technique for the detection of long-lived radionuclides through ultra-low isotope ratio measurements. In many cases, counting atoms rather than decays yields much higher sensitivities. The potential of AMS will be demonstrated on typical radionuclides of interest with half-lives between some tens of years up to a hundred million years. The precise measurement of the 27Al(n,2n)26Al excitation function will be exemplified. Lack of information exists for a list of nuclides as pointed out by nuclear data requests. A brief overview on detection limits and some applications for selected long-lived radionuclides is given.

International Nuclear Information System (INIS)

Studies of Rydberg-atom destruction in collisions with the polar targets CH_3I and CH_2Br_2 for values of principal quantum number n in the range 100--400 are reported. Analysis of the data using the essentially-free-electron model suggests that, for ultralow electron energies (#approx#80 #mu#eV to 1 meV), the cross section #sigma#(var-epsilon) for rotationally inelastic scattering of electrons by a polar target varies approximately as 1/var-epsilon, where var-epsilon is the electron energy. The Born approximation does not predict such behavior at very low collision energies, and possible reasons for this discrepancy are discussed.

Science.gov (United States)

The classical Stefan theory for the melting of a solid or the freezing of a liquid is too simplistic to describe phenomena such as supercooling, in which a liquid supports temperatures below its freezing point, or superheating, the analog for solids, or d...

CERN Document Server

Offers comprehensive coverage of the field of electrical double layer (EDL) research. This work discusses theoretical models used with EDL and demonstrates how they can be applied to typically encountered real-world problems including those that must be considered in modern industrial applications.

Energy Technology Data Exchange (ETDEWEB)

Metallic multilayers offer a fantastic playground to investigate elastic stresses in films of nanometer thickness. We will present and discuss a few examples from our recent work on Au-Ni and Ag-Cu systems where we combined plate bending measurements and electron or X-ray diffraction to investigate stress buildup and interfacial mixing. Comparing these two cases we discuss the results with respect to basic parameters like the misfits in lattice parameters and in elastic moduli, the mixing enthalpies and the surface energies.

Energy Technology Data Exchange (ETDEWEB)

A safety analysis code, named as SPACE, for a pressurized water reactor is under development to obtain a licensing to be used for the PWR design and to hold entire proprietary rights. The task of KAERI is to develop the physical models and correlations which are required to solve the field equations. It can be divided into four parts; i) flow regime determination, ii) wall heat transfer, iii) wall and interfacial friction, iv) interfacial heat and mass transfer. This paper will describe the process to develop the models for the two-phase flow regime maps in the horizontal and vertical pipes.

Energy Technology Data Exchange (ETDEWEB)

The interfacial area transport equation dynamically models the two-phase flow regime transitions and predicts continuous change of the interfacial area concentration along the flow field. Hence, when employed in the numerical thermal-hydraulic system analysis codes, it eliminates artificial bifurcations stemming from the use of the static flow regime transition criteria. Accounting for the substantial differences in the transport phenomena of various sizes of bubbles, the two-group interfacial area transport equations have been developed. The group 1 equation describes the transport of small-dispersed bubbles that are either distorted or spherical in shapes, and the group 2 equation describes the transport of large cap, slug or churn-turbulent bubbles. The source and sink terms in the right-hand-side of the transport equations have been established by mechanistically modeling the creation and destruction of bubbles due to ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this 3.5 year project is to develop a commercially competitive vehicle powered by ethanol (or ethanol blend) that can meet California`s ultra-low emission vehicle (ULEV) standards and equivalent corporate average fuel economy (CAFE) energy efficiency for a light-duty passenger car application. The definition of commercially competitive is independent of fuel cost, but does include technical requirements for competitive power, performance, refueling times, vehicle range, driveability, fuel handling safety, and overall emissions performance. This report summarizes a system design study completed after six months of effort on this project. The design study resulted in recommendations for ethanol-fuel blends that shall be tested for engine low-temperature cold-start performance and other criteria. The study also describes three changes to the engine, and two other changes to the vehicle to improve low-temperature starting, efficiency, and emissions. ...

International Nuclear Information System (INIS)

Multi-dimensional modelling of two-phase flow requires accurate constitutive relationships for interfacial parameters such as interfacial heat transfer, void fraction distribution, interfacial area, etc. However, existing diagnostic systems for measurement of two-phase flow parameters have difficulty measuring two or three-dimensional void distributions required for determination of interfacial parameters. In this work, a Real-Time Neutron Radiography (RTNR) system is developed for non-intrusive measurement of two-phase flow parameters in nuclear fuel channels at low thermal neutron fluxes (on the order of 10"6n/cm"2-s). This advanced radiation technique has the advantage of measuring two-phase flow in 3 1/2 dimensions (x,#integral#dy,t) where the 1/2 dimension refers to an integrated or averaged space dimension. Pipe flow channels, annulus flow channels, MAPLE-type nuclear fuel flow channels, and ...

Energy Technology Data Exchange (ETDEWEB)

The 'high-tension distribution line design support system' was developed for the 'work design support system'. This support system is composed of the work outline editor for preparing work details and facility data and the inference engine for preparing practical design plans, and can check system conditions such as voltage drop and deviation from technical standards automatically. The work outline editor takes charge of selection of work items, selective input of system information, and setting of some conditions such as pole position and reserved load onto a system diagram. The inference engine provides the design plan automatically based on the information inputted by the editor. For the design of high-tension distribution line, such various factors as local condition and load sharing of distribution systems should be considered. This design support system attains efficient processing by not total ...

British Library Electronic Table of Contents (United Kingdom)

Post-tensioned (PT) self-centering moment frames have been developed as an alternative to typical moment-resisting frames (MRFs) for earthquake resistance. When a PT frame deforms laterally, gaps between the beams and columns open. However, the gaps are constrained by the columns and the slab in a real PT self-centering building frame. This paper presents a methodology for evaluating the column restraint and beam compression force based on the column deformation and gap openings at all stories. The method is verified by cyclic tests of a full-scale, two-bay by one-story PT frame. Moreover, a sliding slab is proposed to minimize restraints on the expansion of the PT frame. Shaking table tests were conducted on a reduced-scale, two-by-two bay one-story specimen, which comprises one PT frame ...

CERN Document Server

The junction conditions for General Relativity in the presence of domain walls with intrinsic spin are derived in three and higher dimensions. A stress tensor and a spin current can be defined just by requiring the existence of a well defined volume element instead of an induced metric, so as to allow for generic torsion sources. In general, when the torsion is localized on the domain wall, it is necessary to relax the continuity of the tangential components of the vielbein. In fact it is found that the spin current is proportional to the jump in the vielbein and the stress-energy tensor is proportional to the jump in the spin connection. The consistency of the junction conditions implies a constraint between the direction of flow of energy and the orientation of the spin. As an application, we derive the circularly symmetric solutions for both the rotating string with tension and the spinning dust string in three dimensions. The rotating string with ...

Energy Technology Data Exchange (ETDEWEB)

A simple model based on surface chemistry is developed, based an simple concepts of contact angle, wetting and spreading. Results of the modeling can be stated by two simplified rules of thumb'': (1) A liquid will spread on the surface of a solid if the surface tension of the liquid is lose than the surface free energy of the solid, and (2) The liquid having the surface tension nearest that of the solid will preferentially wet the surface of the solid. These two rules can then be used to define the parameters that constitute a process for formulating a plastic bonded explosive (PBX), which is a crystalline high-explosive material coated with a small amount of plastic polymeric material (the binder). The PBX then can be pressed to a high density, and machined to a specific shape. The pressed and machined explosive material can then be used in a physics experiment to study fundamental properties of either the explosive or some ...

CERN Document Server

565 deg C occurs when dissolution rate exceeds oxidation rate, exposing the fresh Al anode to the glass melt. Under inert atmosphere (at 583 deg C), air oxidation is not possible and galvanic cell redox reactions generate an excessive copper interlayer as the system attempts to sustain the oxide layer at the anode. Similar behaviour is observed in those coatings formed on the alloy using glass C (containing Al sub 2 O sub 3 and Na sub 2 O). In this case, the interfacial reactions involve the PbO of the glass and Pb-rich spherical precipitates are formed in the interfacial region, along side sodium aluminosilicate phases, precipitated from the PbO-depleted glass. The behaviour in both systems indicates that oxygen diffuses through the edge of the glass drop, from the atmosphere, to the substrate/glass interface. Coatings formed on the MMCs in air exhibited a porosity of approx 10%, attributed to the production of CO sub 2 gas through the ...

Energy Technology Data Exchange (ETDEWEB)

. This study investigates the geometric effects of 90-degree vertical elbows and flow configurations in two-phase flow. The study shows that the elbows make a significant effect on the transport characteristics of two-phase flow, which includes the changes in interfacial structures, bubble interaction mechanisms and flow regime transition. The effect of the elbows is characterized for global and local two-phase flow parameters. The global two-phase flow parameters include two-phase pressure, interfacial structures and flow regime transition. In order to characterize the frictional pressure drop and minor loss across the vertical elbows, pressure measurements are obtained across the test section over a wide range of flow conditions in both single-phase and two-phase flow conditions. A two-phase pressure drop correlation analogous to Lockhart-Martinelli correlation is proposed to predict the minor loss across the elbows. A high speed camera is ...

Energy Technology Data Exchange (ETDEWEB)

Momentum transfer through an air-water interface was studied in a horizontal rectangular channel through experimental and numerical analysis. The liquid flow Reynolds numbers, based on hydraulic diameters, were 11500 and 17000. The air flow Reynolds number varied from 0 to 3260. In experiments, velocity distribution was measured by hot-film and hot-wire probes. The effect of the liquid flow Reynolds number and the direction of interfacial shear stress was investigated by performing the cocurrent and countercurrent experiments. The modified k-{epsilon} model was able to reproduce these experimental results qualitatively. The range of applicability of the modified k-{epsilon} model was also discussed. (author).

British Library Electronic Table of Contents (United Kingdom)

A novel thin-film composite polyamide nanofiltration membrane was prepared through interfacial polymerization of polymeric polyamine polyvinylamine (PVAm) with isophthaloyl chloride (IPC) on a polysulfone supporting film. The composite membranes were prepared under different conditions and characterized in terms of chemical and morphological structures, surface zeta potential, pure water permeability, and rejection to different solutes including electrolytes and sucrose. The results showed that the membrane performance was significantly affected by the content of amine units of PVAm and the concentrations of PVAm and IPC. The increase of the content of amine units of PVAm and the concentration of IPC resulted in an augment in salt rejection and a decrease in permeability, while the increas...

Energy Technology Data Exchange (ETDEWEB)

The growth of thin Pd[sub 2]Si films on Si(111) surfaces is studied using [ital in] [ital situ] transmission electron microscope under ultrahigh vacuum conditions. No immediate reaction of deposited Pd with Si is observed at room temperature. At [similar to]200 [degree]C, uniform Pd[sub 2]Si films can be formed. The thin Pd[sub 2]Si films are found to grow into strained islands at elevated temperatures. Interfacial misfit dislocations associated with interfacial steps propagate across the strained islands, causing the islands to grow layer-by-layer at the interface. The strain fields associated with the misfit dislocations are believed to be responsible for this behavior.

CERN Document Server

Several observational studies suggest that solar wind dynamic pressure fluctuations can drive magnetospheric ultra-low frequency (ULF) waves on the dayside. To investigate this causal relationship, we present results from Lyon-Fedder-Mobarry (LFM) global, three-dimensional magnetohydrodynamic (MHD) simulations of the solar wind-magnetosphere interaction. These simulations are driven with synthetic solar wind input conditions, where idealized ULF dynamic pressure fluctuations are embedded in the upstream solar wind. In three of the simulations, a monochromatic, sinusoidal ULF oscillation is introduced into the solar wind dynamic pressure time series. In the fourth simulation, a continuum of ULF fluctuations over the 0-50 mHz frequency band is introduced into the solar wind dynamic pressure time series. In this numerical experiment, the idealized solar wind input conditions allow us to study only the effect of a fluctuating solar wind dynamic pressure, while holding ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, we propose to characterize boron transient enhanced diffusion (TED) for processes currently used for P{sup +}/N ultra-shallow junctions (USJ) fabrication. Indeed, the fundamental understanding of boron diffusion for low energy boron implantation is mandatory to evaluate the scalability of such processes for the coming complementary metal-oxide-semiconductor (CMOS) transistor generations. In these experiments, we characterize the boron anomalous diffusion, thanks to boron buried marker-layers obtained by epitaxial growth. B{sup +} and BF{sub 2}{sup +} ultra-low energy (ULE) implantations and plasma doping (PLAD) using BF{sub 3} as precursor gas are carried out to compare the two techniques used for advanced USJ fabrication. Boron diffusion behaviors are analyzed via secondary ion mass spectrometry for annealing at 700 deg. C for 5 min and 15 min. Finally this paper brings some physical insights explaining the technological benefit coming from PLAD ...

Energy Technology Data Exchange (ETDEWEB)

Graphite fluoride (CF{sub x}) is investigated as an additive for WS{sub 2} thin films to reduce its sensitivity to moisture. The films are grown onto hardened 440C stainless steel disks by pulsed laser deposition using the 248 nm line from an excimer laser. Substrate temperature and additive concentration are varied to control film chemistry and crystal structure. The effect of relative humidity (i.e., < 1 to 85% RH) on friction is evaluated. Coatings grown at RT from targets with a low concentration of CF{sub x} exhibit ultra-low friction (ULF) behavior in dry air (i.e., {mu} {<=} 0.01), but friction increases with RH. Mechanisms for the ULF behavior are proposed which suggest that further reductions in friction are possible. Films grown at 300 C or with higher concentrations of CF{sub x} are relatively insensitive to humidity, but have more typical friction coefficients ({mu} {<=} 0.04) in dry air. (orig.)

Energy Technology Data Exchange (ETDEWEB)

We have investigated the diffusion enhancement mechanism of boron-enhanced diffusion (BED), wherein boron diffusivity is enhanced four to five times over the equilibrium diffusivity at 1050&hthinsp;{degree}C in the proximity of a silicon layer containing a high boron concentration. It is demonstrated that BED is driven by excess interstitials injected from the high boron concentration layer during annealing. For evaporated layers, BED is observed above a threshold boron concentration between 1{percent} and 10{percent}, though it appears to be closer to 1{percent} for B-implanted layers. For sub-keV B implants above the threshold, BED dominates over the contribution from transient-enhanced diffusion to junction depth. For 0.5 keV B, this threshold implantation dose lies between 3{times}10{sup 14} and 1{times}10{sup 15} cm{sup {minus}2}. It is proposed that the excess interstitials responsible for BED are produced during the formation of a silicon boride phase in the high B ...

Energy Technology Data Exchange (ETDEWEB)

We investigated the electrical characteristics and the junction depth of ultra-shallow junctions formed by using the plasma-doping method. Compared with ultra-low energy boron-ion implantation at 500 eV, the junctions formed with the plasma-doping process exhibited shallow junction depths and low sheet resistances. The junction depths of the plasma-doped samples were 150 A and 330 A after annealing for 10 s at 900 .deg. C and 950 .deg. C, respectively. For the same junction depth, the sheet resistance of the B{sub 2}H{sub 6} plasma-doped sample was an order of magnitude less than that of the 500-eV B-ion implanted sample. Cross-sectional transmission electron microscopy and deep level transient spectroscopy showed that the defects formed by the B{sub 2}H{sub 6} plasma-doping process could be removed by annealing at 950 .deg. C for 10 s. The scaling of metal-oxide-semiconductor field-effect-transistor (MOSFET) device channel lengths for high-speed application ...

Energy Technology Data Exchange (ETDEWEB)

The strain gradient crystal plasticity theory is applied to study the deformation of planar single crystal with a void under a nominally uniaxial tension. The crystal theory assumes elevated strain hardening due to slip gradients and has a constitutive length scale. The effects of the void size with respect to the constitutive length scale on the single crystal deformation are investigated.

Wastenet

... 03/08/2011 Professor named Chair at Epworth Hospital Professor Nilmini Wickramasinghe from the College of Business at RMIT University has been named Epworth Chair, Health Information Management , by Epworth HealthCare. 26/07/2011 Study investigates drug-free relief for tension headaches As Australia marks its first National Pain Week ...

Energy Technology Data Exchange (ETDEWEB)

We consider a generalization of the DGP model, by adding a second brane with localized curvature, and allowing for a bulk cosmological constant and brane tensions. We study radion and graviton fluctuations in detail, enabling us to check for ghosts and tachyons. By tuning our parameters accordingly, we find bigravity models that are free from ghosts and tachyons. These models will lead to large distance modifications of gravity that could be observable in the near future.

Energy Technology Data Exchange (ETDEWEB)

This work has analyzed the key variables of indentation tip radius, contact radius, delamination radius, residual stress and superlayer/film/interlayer properties on nanoindentation measurements of adhesion. The goal to connect practical works of adhesion for very thin films to true works of adhesion has been achieved. A review of this work titled ''Interfacial toughness measurements of thin metal films,'' which has been submitted to Acta Materialia, is included.

Energy Technology Data Exchange (ETDEWEB)

The addition of titanium to eutectic braze compositions causes these alloys to readily wet and bond to A1N ceramics. Electron microscopic characterizations of the metal-ceramic interfaces reveal the presence of TiN, along with other Ti- and Al-containing phases. The formation of such interfacial reaction products is an additional thermodynamic driving force for the creation of useful metal-ceramic bonds. 12 refs., 4 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

In studying the absorption of carbon dioxide by absorbents impregnated with alkanol amines, researchers used a laboratory-scale packed column to determine the overall gas-phase mass-transfer coefficients and enhancement factors. A model derived for the mechanism of the chemical reaction taking place in the interfacial layer accounts for the effect of the reaction upon the absorption rate better than other models.

Energy Technology Data Exchange (ETDEWEB)

Sputter-removal rates of overlayer and interfacial species on silicon are analyzed to determine sputtering yields for the species involved. Sputtering yields up to two orders of magnitude lower than those measured for silicon are found, and the results are interpreted in terms of a cascade mixing process which continually reburies much of the overlayer material beyond the escape depth of the sputtered atoms.

Energy Technology Data Exchange (ETDEWEB)

Three-dimensional dynamics of a compact toroid (CT) plasmoid, which is injected into a magnetized target plasma region is investigated by using magnetohydrodynamic (MHD) numerical simulations. It is found that the process of the CT penetration into this region is much more complicated than what has been analyzed so far by using a conducting sphere (CS) model. The injected CT suffers from a tilting instability, which grows with the similar time scale as the CT penetration. The instability is accompanied by magnetic reconnection between the CT magnetic field and the target magnetic field, which disrupts the magnetic configuration of the CT. Magnetic reconnection plays a role to supply the high density plasma initially confined in the CT magnetic field into the target region. Also, the penetration depth of the CT high density plasma is examined. It is shown to be shorter than that estimated from the CS model. The CT high density plasma is decelerated mainly by the Lorentz force of the ...

DEFF Research Database (Denmark)

Wharton's jelly contains large amounts of hyaluronic acid, and glucosamine is an important constituent of this macromolecule. In order to evaluate the placental vascular effects of this aminosugar, small chorionic and stem villous arteries were dissected from placental specimens obtained at normal term vaginal deliveries (n = 15). Ring preparations were mounted in organ baths, and isometric wall tensions were measured. Glucosamine and its epimer galactosamine (5 X 10(-4) to 10(-2) M) produced marked relaxation of contractions induced by PGF2 alpha (10(-5) M) in both chorionic and stem villous arteries. The effect was unchanged after pretreatment with atropin, propranolol and indomethacin. The relaxant effect of the neutral sugar mannose was less pronounced compared with that of the hexosamines. Total tissue concentrations of placental hexosamines have been reported within the range needed to produce placental vascular relaxation in the present study. However, the ...

Energy Technology Data Exchange (ETDEWEB)

Research and development underway since 1982 has led to the development of a method of reinforcing wood and wood composite structural products (WWC) using high-strength fiber-reinforced plastic. This method allows the use of less wood fiber and lower grade wood fiber for a given load capacity. The first WWC in which reinforcement has been marketed is glulam beams. Marketed under the trade name FiRP{trademark} Reinforced glulam, the product has gained code approval and is now being used in the construction of buildings and bridges in the United States, Japan and other countries. The high-strength fiber-reinforced plastic (FiRP{trademark} Reinforced panel (RP)) has specific characteristics that are required to provide for proper use in WWC`s. This paper discusses these characteristics and the testing requirements to develop code approved allowable design values for carbon, aramid and fiberglass RP`s for such uses. Specific issues such as in-service characteristics, i.e. long term creep ...

Science.gov (United States)

Hot-torsion testing was used to establish the cavitation behavior of a typical alpha/beta titanium alloy, Ti-6Al-4V, with a colony microstructure, during simple-shear deformation. For this purpose, sections of deformed specimens were examined by optical metallography, and by scanning and orientation-imaging microscopy (OIM). It was found that cavity nucleation occurred along prior beta boundaries as well as at triple points; in particular, most cavities nucleated along boundaries perpendicular to the axial direction of the specimen. Extensive growth was observed for cavities surrounded by both hard and soft orientations, with the soft colonies accommodating more of the imposed strain. At high degrees of deformation, dynamic globularization of the colony microstructure adjacent to the cavities was also observed. In addition, the metallographic observations revealed that the cavities did not grow in an equiaxed mode, but in an elliptical manner. A tensor describing the cavity-growth rate ...

Energy Technology Data Exchange (ETDEWEB)

Until 1990, in Tuscany, salt pollution of anti-salt insulators installed on high-tension transmission lines had led to rare breakdowns. On the contrary, in the last months of 1990, in most of Tuscany, following a strong libeccio wind coming from the Tyrrhenian Sea, and due to a long period of drought, salt deposits accumulated on the insulators of the high-voltage transmission lines (380 kV, 220 kV and 132 kV). This phenomenon not only took place in the coastal areas near Livorno, Pisa and Grosseto, but also in areas far away from the sea such as Florence, Prato, Arezzo and Siena. Following this, several high-tension lines, and whole sections of 380 kV electric stations went out of order, damaging the stations' equipment, insulators on the lines, and in particular porcelain insulators. The maintenance operations that were immediately undertaken consisted in washing operations, first focussed on stations, and then on lines. Several ...

British Library Electronic Table of Contents (United Kingdom)

The effect of particle/matrix interface debonding on composites consisting of elastic particles and viscoelastic matrix is studied. The interface debonding is represented by a nonlinear cohesive law for the high explosive PBX 9501. The Mori-Tanaka method gives the constitutive relation of the composite in terms of the properties of elastic particles, viscoelastic matrix, and nonlinear cohesive law for interfaces. For the example of a composite with spherical particles subject to hydrostatic tension, simple analytical expressions of the composite stress-strain relation are obtained. The strain rate and temperature have strong effects on the composite behavior. High strain rate and low temperature give high strength of the composite. However, the rate and temperature effects decrease as the ...

International Nuclear Information System (INIS)

By the methods of microstructural and electron-microscopic analyses by the tension test and impact test studied is the effect of quenching conditions on structure and mechanical properties of the TS6 titanium-#beta# alloy. It is shown that low temperature quenching from 700 deg C, recommended earlier for analogous VT15 titanium alloy, leads to appearence of intercrystalline fracture and to sharp decrease of impact strength of the TS6 alloy. Established are optimum conditions for quenching of half-finished products and articles of the TS6 alloy depending on their subsequent working or operation.

British Library Electronic Table of Contents (United Kingdom)

Current multi-scale computational models of ventricular electromechanics describe the full process of cardiac contraction on both the micro- and macro- scales including: the depolarization of cardiac cells, the release of calcium from intracellular stores, tension generation by cardiac myofilaments, and mechanical contraction of the whole heart. Such models are used to reveal basic mechanisms of cardiac contraction as well as the mechanisms of cardiac dysfunction in disease conditions. In this paper, we present a methodology to construct finite element electromechanical models of ventricular contraction with anatomically accurate ventricular geometry based on magnetic resonance and diffusion tensor magnetic resonance imaging of the heart. The electromechanical model couples detailed repres...

Energy Technology Data Exchange (ETDEWEB)

A full scale experiment was carried out to investigate the texture characteristics of the falling water of free falling and slope failing types. According to the increase of Reynolds number, the texture of falling water was classified into three categories for both types: stability of free surface, transition and whole turbulence. In the first category the stability of the free surface was related to the growth of minute disturbance. Surface tension works as a counter, force to the disturbance in free falling water, and gravity in slope falling water. 14 refs., 15 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

This paper reports that the point defect model for steady-state passive films formed anodically on metal s in aqueous environments has been extended to include irreversible dissolution of the film and the irreversible generation and annihilation of cation and oxygen vacancies at the metal/film and film/solution interfaces. THe model yields a number of diagnostic criteria that can be used to identify the majority (vacancy) charge carrier and to characterize the kinetic nature of the interfacial vacancy generation and annihilation processes. We use these criteria to show that the steady-state passive film that forms on nickel in acidic phosphate buffer solutions is a cation conductor and that cation transport from the metal to the solution involves irreversible ejection of cations from the film. On the other hand, the passive film that forms on tungsten in the same environment under steady-state conditions is found to be an oxygen ion conductor with the passive ...

British Library Electronic Table of Contents (United Kingdom)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr2N, CrN, TiN, V2N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of scale-up studies to determine the feasibility of extending the nitridation approach to thin 0.1mm stainless steel alloy foils for proton exchange membrane fuel cell (PEMFC) bipolar plates. Developmental Fe-20Cr-4V alloy and type 2205 stainless steel foils were treated by pre-oxidation and nitridation to form low-ICR, corrosion-resistant surfaces. As-treated Fe-20Cr-4V foil exhibited target (low) ICR values, whereas 2205 foil suffered from run-to-run variation in ICR values, ranging up to 2x the...

Energy Technology Data Exchange (ETDEWEB)

Type 440C stainless steel is a high-C, high-Cr martensitic steel used in applications requiring high hardness and wear resistance in combination with moderate corrosion resistance. Typical applications include precision aerospace bearings and critical components in computer disk drives. The properties of passive films formed on 440C steel were investigated using advanced electrochemical techniques with a view to establishing a method to measure film stability directly in the passivation baths. Electrochemical measurements were sensitive to the passive film properties and were able to quantify the effect of cooling rate on passive film stability. The techniques used included linear polarization, AC impedance, small amplitude cyclic voltammetry, and coulostatic transient measurements. These provided results that exhibited excellent agreement with the AC impedance technique providing the most information about the interfacial reactions. It was found that the full ...

International Nuclear Information System (INIS)

The anodic reaction kinetics and interfacial mass transport of a direct polymer electrolyte membrane formic acid fuel cell have been investigated in an all solid-state electrochemical cell using a highly active nanostructured palladium-gold alloy microelectrode as an in situ probe. Well-defined 'S-shaped' steady-state cyclic voltammograms exhibiting current-rising region at lower overpotentials and limiting current region at higher overpotentials have been first obtained for the electrochemical oxidation of formic acid at varying temperature. The 'S-shaped' steady state polarization curves and chronoamperometric curves enable convenient measurements of the anodic reaction kinetics and interfacial mass transport of formic acid under real polymer electrolyte membrane conditions. It is encouragingly found that formic acid can be directly oxidized to CO2 with the first electron transfer being the likely rate-determining step and the formation of ...

Energy Technology Data Exchange (ETDEWEB)

A copyrighted computational fluid dynamics computer code, ICOMFLO, has been developed for the simulation of multiphase reacting flows. The code solves conservation equations for gaseous species and droplets (or solid particles) of various sizes. General conservation laws, expressed by elliptic type partial differential equations, are used in conjunction with rate equations governing the mass, momentum, enthalpy, species, turbulent kinetic energy, and turbulent dissipation. Associated phenomenological submodels of the code include integral combustion, two parameter turbulence, particle evaporation, and interfacial submodels. A newly developed integral combustion submodel replacing an Arrhenius type differential reaction submodel has been implemented to improve numerical convergence and enhance numerical stability. A two parameter turbulence submodel is modified for both gas and solid phases. An evaporation submodel treats not only droplet evaporation but size ...

Energy Technology Data Exchange (ETDEWEB)

In 2003, Vehicle Emissions Team of the Clean Air Strategic Alliance (CASA) decided to explore ways to reduce vehicle emissions such as particulate matter, nitrogen oxides, carbon monoxide, and hydrocarbons from diesel engines. One of the options for reducing emissions from diesel engines, a diesel particulate filter (DPF), is the subject of a demonstration project to test the effectiveness of the Johnson Matthey diesel particulate filter called Continuously Regenerating Technology (CRT) under cold weather conditions. The project involved filter testing between January 2003 and January 2004 on two diesel buses in Edmonton Transit System's (ETS) fleet. Vehicle exhaust emissions were tested for total hydrocarbons, nitrogen oxides, carbon monoxide, carbon dioxide, and particulate matter. The objectives of the project were to: prove the effectiveness of DPF under cold weather conditions in Alberta; provide an opportunity for hands-on installation experience and use of CRT ...

Energy Technology Data Exchange (ETDEWEB)

A comprehensive understanding of dopant activation mechanisms in crystalline Si is required in order to form shallow junctions. In this paper, we will review several experimental assessments on boron clustering and novel methods to form shallow junctions. Boron marker-layer structures have been used to investigate the fundamental aspects of formation and ripening boron-interstitial clusters (BICs) and their influence on the associated transient enhanced diffusion (TED). The samples were damaged by Si implants at different doses in the sub-amorphizing range and annealed at high temperatures. We found that BICs act as a sink for interstitials at supersaturations values S(t)>10{sup 4}. This implies that silicon self-interstitial defects are the primary source of interstitials driving TED, and that BICs act as a secondary 'buffer' for the interstitial supersaturation. These clusters are less sensitive to the ripening process than pure interstitial clusters do, so ...

Energy Technology Data Exchange (ETDEWEB)

A historical review on insulated cables for power transmission, is presented, beginning with impregnated paper insulation, oil filled cables and natural rubber cables. High density and chemically reticulated polyethylene were then used for high voltage and very high voltage cables; the advantages of polyethylene compared to impregnated paper cables are discussed, which led to research programs at EDF on various themes concerning the optimization of polyethylene cables: dielectric properties and reliability, thermomechanical behaviour, thermal ageing of materials, testing methods (acceptance dielectric test and long duration temperature test); utilization of low- and high-density and chemically reticulated polyethylene for 225 kV cables is discussed

British Library Electronic Table of Contents (United Kingdom)

The Spratly Islands constitute one of the earth's most ecologically significant areas, hosting a high diversity of marine species, providing critical habitats for endangered species, and providing marine larvae to reestablish depleted stocks among the heavily overfished and degraded coastal ecosystems of the South China Sea. Territorial disputes have led to the establishment of environmentally destructive, socially and economically costly military outposts on many of the islands. Given the rapid proliferation of international peace parks around the world, it is time to take positive steps toward the establishment of a Spratly Islands Marine Peace Park. Its purpose would be to manage the area's natural resources and alleviate regional tensions via a freeze on claims and claim supportive act...

British Library Electronic Table of Contents (United Kingdom)

A hypofunctionality of Gi proteins has been found in migraine patients. The fixed combination of indomethacin, prochlorperazine and caffeine (Indoprocaf) is a drug of well-established use in the acute treatment of migraine and tension-type headache. The aim of this study was to investigate if Indoprocaf was able to exert its central antinociceptive action when Gi proteins activity is abolished by pertussis toxin (PTX), compared to its single active ingredients and to sumatriptan. The mice model of abdominal constriction test induced by an i.p. injection of a 0.6% solution of acetic acid was used. The study showed that Indoprocaf (a fixed combination of indomethacin 1?mg/kg, prochlorperazine 1?mg/kg and caffeine 3?mg/kg, s.c.) and sumatriptan (20?mg/kg, s.c.) exert their central antinocicep...

British Library Electronic Table of Contents (United Kingdom)

A series of cleavable water-soluble silicone surfactants were prepared by the reaction of a hydroxyl-terminated polyester and an organopolysiloxane. Cleavable surfactants can decompose into water-insoluble moiety of silanol and two water-soluble products under acidic conditions, whereas these compounds are stable under neutral or alkaline conditions. The structure change of theses cleavage products are confirmed by IR and UV spectra analysis. The fundamental surface activity including surface tension, foaming, contact angle and viscosity are studied. The photocatalytic degradation of modified silicone surfactants with UV light over titanium oxide was investigated. Experimental results have confirmed that products are slowly degraded by direct photolysis. However, the cleavable silicone sur...

International Nuclear Information System (INIS)

Strain embrittlement in Ti base alloys during tensile testing was investigated. Results show that in an #alpha#-#beta# titanium alloy the local activity of H in alpha phase (#alpha#/sub H//sup #alpha#) increases and activity of H in beta phase (#alpha#/sub H//sup #beta#) decreases as the equiaxed #alpha# particle size decreases at constant volume fraction of phases. Thus with decreasing particle size there would be a tendency for H to move from #alpha# to #beta#, decreasing the H content of #alpha#. Also whether H tended to move from #beta# to #alpha# or from #alpha# interiors to the #alpha#-#beta# interface this tendency would be reduced by surface tension effects, making the alloy less susceptible to embrittlement.

Energy Technology Data Exchange (ETDEWEB)

The Spratly Islands are developing into a flashpoint in the South China Sea region. Geological surveys conducted underneath the seabed of these islands following the oil crisis in the 1970s shows an enormous potential of oil and gas reserves. Moreover, with the adoption of the new International Law of the Sea concept there are overlapping claims by contending countries. Unless these claimant countries reconcile their differences and come to terms, the conflict is bound to escalate. This thesis is an in depth study of the disputes over the Spratlys and examines four cases of islands based territorial disputes that could be used as a model in resolving these tensions. This thesis argues that a military option will only create division and in-flame longstanding animosities. Instead, a peaceful solution is recommended as quickly as possible so that regional nations will realize the full potential of these islands. Spratly Islands in the South China Sea.

Science.gov (United States)

Since 1970, officers on the Seattle campus have regularly patrolled the hallways of dormitories of the University of Washington. It is a community-policing strategy, a low-key way to engage students. However, the practice might cease this fall. In June, the state's Court of Appeals ruled that students have the same right to privacy in dormitory hallways as they do in their rooms. Therefore, the court concluded, campus police officers lack the legal authority to randomly patrol residence halls. Although the closely watched ruling bears on only one state, it reveals the tension between privacy and security in dormitories everywhere. Residence halls are legally complex spaces, where crime often creeps in and where residents, perhaps more than ever, expect administrators and police officers to ensure their safety.

Energy Technology Data Exchange (ETDEWEB)

A flow pattern or flow regime is the characteristics spatial distribution of the phases of fluid in a duct. Since heat transfer and pressure drop are dependent on the characteristic distribution of the phases, it is necessary to describe flow patterns in an appropriate manner so that a hydrodynamic or heat transfer theory applicable to that pattern can be chosen. The objective of the present analysis is to create a flow regime map based on physical modeling of vapor/liquid interaction phenomena in a microgravity environment. In the present work, four basic flow patterns are defined: dispersed flow, stratified flow, slug flow, and annular flow. Fluid properties, liquid and vapor flow rates, and pipe size were chosen as the principal parameters. It is assumed that a transition from one flow pattern to another will occur when there is a change in the dominant force which controls that flow pattern. The forces considered in this modeling are surface tension force, both ...

British Library Electronic Table of Contents (United Kingdom)

Statement of problem Because noble dental casting alloys for metal ceramic restorations have a wide range of mechanical properties, knowledge of these properties is needed for rational alloy selection in different clinical situations where cast metal restorations are indicated. Purpose The purpose of this study was to compare the mechanical properties and examine both the fracture and polished surfaces of 6 noble casting alloys that span many currently marketed systems. Five alloys were designed for metal ceramic restorations, and a sixth Type GPT has Type IV alloy for fixed prosthodontics (Maxigold KF) was included for comparison. Material and methods Specimens (n=6) meeting dimensional requirements for ISO Standards 9693 and 8891 were loaded to failure in tension using a universal testin...

Energy Technology Data Exchange (ETDEWEB)

The program introduced here for determining and describing the multi-axial creep of pipes is based, on the one hand, on the results of the nuclear process heat prototype plant material program and, on the other hand, on the possible load conditions which arise for evaluating accidents or extreme working situations. The basis of a theoretical description of multi-axial creep is the invariant theory in which both the von Mises configuration change hypothesis and the Norton creep law are included. Combined tension and torsion are also considered in detail, the superimposition of cyclic stresses in the tensile threshold area is discussed and cases of partial relaxation are explained. Experimental results for the discussed loads are introduced, which have led to satisfactory agreement between theory and experiment. (orig./MM).

British Library Electronic Table of Contents (United Kingdom)

Propanolol is a betablocker drug used in the treatment of arterial hypertension related diseases. In order to achieve an optimal performance of this drug it is important to consider the possible interactions of propanolol with plasma proteins. In this work, we have used several experimental techniques to characterise the effect of addition of the betablocker propanolol on the properties of bovine plasma fibrinogen (FB). Differential scanning calorimeter (DSC), circular dichroism (CD), dynamic light scattering (DLS), surface tension techniques and atomic force microscopy (AFM) measurements have been combined to carry out a detailed physicochemical and surface characterization of the mixed system. As a result, DSC measurements show that propranolol can play two opposite roles, either acting ...

International Nuclear Information System (INIS)

Co-current stratified flow of liquid metal and water was investigated in a horizontal rectangular channel. Position of the interface pressure drop and direct contact heat transfer between these immisci ble liquids were measured in a fully developed flow. A turbulence model was proposed to explain the experimental results considering that the turbulence is damped near the liquid-liquid interface by surface tension. The analytical results showed good agreement with the experimental ones. Main results are that (1) position of the interface mainly depends on the flow rate ratio of both liquids, that (2) the pressure drop is approximately proportional to square of the average velocity of water, and that (3) heat transfer rate at direct contact interface is several times higher than that of co-current flow separated by a thin solid plate. (author).

British Library Electronic Table of Contents (United Kingdom)

Durability is a major limitation of current proton exchange membrane fuel cells. Mechanical stress due to hygro-thermal cycling is one failure mechanism of the polymer electrolyte membrane. In previous work the cyclic rate, temperature, and hydration dependent elastic-viscoplastic mechanical behavior of Nafion has been extensively investigated in uniaxial and biaxial tension, serving as a data basis and means of validation for a three-dimensional constitutive model. Here, the important effect of loading via constrained swelling is studied. Specifically, two types of loading are investigated: partially constrained swelling via a bimaterial swelling test and hygro-thermal cycling within a fuel cell. The bimaterial swelling conditions are examined via experiments in conjunction with modeling....

Science.gov (United States)

A 65-yr-old female developed cough, fever and dyspnoea following repeated exposure to a home ultrasonic humidifier. High-resolution computed tomography showed ground-glass opacity in both lung fields. Arterial blood gas analysis gave an oxygen tension of 8.38 kPa (63 Torr). Pulmonary function testing revealed restrictive ventilatory impairment with a reduction in the diffusing capacity. The diagnosis of extrinsic allergic alveolitis (EAA) was confirmed by radiographic findings, pathological evidence of alveolitis and reproductive development by a provocation test to the humidifier water. The yeast Debaryomyces Hansenii was the only microorganism cultured from the water of the humidifier. The double diffusion precipitating test and lymphocyte proliferative response was positive for an extract of D. Hansenii, providing evidence to incriminate this fungus. This is the first described case of EAA caused by D. Hansenii. PMID:12449192

Science.gov (United States)

The invention is a mechanism for retaining an electrical transmission line. In one embodiment of the invention it is a system for retaining an electrical transmission line within downhole components. The invention allows a transmission line to be attached to the internal diameter of drilling components that have a substantially uniform drilling diameter. In accordance with one aspect of the invention, the system includes a plurality of downhole components, such as sections of pipe in a drill string, drill collars, heavy weight drill pipe, and jars. The system also includes a coaxial cable running between the first and second end of a drill pipe, the coaxial cable having a conductive tube and a conductive core within it. The invention allows the electrical transmission line to withstand the tension and compression of drill pipe during routine drilling cycles.

International Nuclear Information System (INIS)

Computer experiments imitating specimen strain on tension with constant deformation rate have been carried out. A formation possibility of atmosphere from defects around gliding dislocations (I) and a work of Frank-Read sources (II) have been accounted for. In result deformation curves until stresses do not exceed a critical shear stress were calculated. Influence of effects (I) and (II) was analyzed. It is determined that both by pass of dislocations over defect ''atmospheres'' and dislocation multiplication can cause a peak in flow stress occurrence on the deformation curves. Reasons and conditions of such peak occurrence have been studied. 12 refs.; 9 figs. (author).

British Library Electronic Table of Contents (United Kingdom)

Aims A depressed cGMP-dependent protein kinase (PKG) activity is implicated in nitrate tolerance. The present study determines whether the leucine zipper-positive (LZ+) isoform of myosin phosphatase target subunit 1 (MYPT1), a key target protein for PKG actions, is involved in the development of nitrate tolerance. Methods and results Nitrate tolerance in in vitro preparations was obtained by a 24 h incubation with nitroglycerin (NTG). Nitrate tolerance in in vivo preparations was obtained by subcutaneous injection of mice with NTG, and the aortas were used. Protein levels of total MYPT1, MYPT1 (LZ+), PP1Cd, myosin light chain (MLC), and phosphorylated MLC were determined by Western blot analysis. Isometric vessel tension was determined by an organ chamber technique. Protein levels of MYPT1...

British Library Electronic Table of Contents (United Kingdom)

This studys purpose was to explore the relationship between creativity and integrity in the ideation phase of feature filmmaking. Integrity refers to ones self-defined ability to maintain authenticity and moral autonomy while preserving ones sense of membership and loyalty to the team or organization. When team members choose elements for the screenplays story that they feel will attract the ideal audience, the dynamic tension between creativity and integrity is most apparent. The forces at play during this phase of work yielded the research question: In what ways and to what degree do screenwriters andor studio executives feel their personal integrity is in alignment with the creative process of feature film development? Several concepts from the literature formed the design around which ...

British Library Electronic Table of Contents (United Kingdom)

BackgroundWave reflection during the systole increases left ventricular (LV) pressure, tension-time index (TTI) and myocardial oxygen requirement. The purpose of this study was to extract that component of extra myocardial oxygen requirement that is due to early systolic wave reflection, define it as wasted effort (?Ew), and examine its relationship to LV hypertrophy (LVH).MethodsRadial artery pressure waveforms were recorded using applanation tonometry and central aortic waveforms generated in 98 patients with untreated hypertension. Aortic augmentation index (AIa), wave reflection amplitude (i.e., aortic augmented pressure (AG)) and systolic duration (ED?Tr), ejection duration (ED) and round-trip travel time of the pressure wave (Tr) were calculated from the aortic waveform, a...

Energy Technology Data Exchange (ETDEWEB)

Kawasaki Steel has constructed many facilities for 15 years to produce cold rolled products and galvanized products in Mizushima Works and Chiba Works. To efficiently and stably produce high and uniform quality products, various new control methods have been developed and applied to these new facilities. Especially, temperature control in a continuous annealing line, zinc coating control in a continuous galvanizing line or paint coating control in a multi-purpose coating line and tension control to achieve stable processing are the most advanced technologies and are introduced in this paper. (author)

Energy Technology Data Exchange (ETDEWEB)

The flexible, insulated, single strand cables are electrically connected with a cylindrical polar tip (PN) by means of cylindrical and conical shafts for the polar tips, which enter the faces of the divided, multiwire strand, clamped by tension half couplings. The flat ends of the polar tips being joined are positioned in two concentric mandrel bushings, an internal fixed one and an external, axially movable bushing (PV). The internal bushing is rigidly attached to the end of the left polar tip and equipped with three or four rounded, radial openings, whose diameter is determined by the external diameter of the locking device hinges (ShF) of the connecting couplings. The right polar tip is equipped with an annular channel of trapezoidal section into which the locking device hinges enter. The external movable bushing on the right side has a conical turning and on the left, a cylindrical into which the cylindrical spring which holds the movable bushing in the extreme ...

British Library Electronic Table of Contents (United Kingdom)

TiO2 hollow microspheres with sea urchin-like hierarchical architectures were synthesized by a simple hydrothermal method. The as-synthesized hollow microspheres with hierarchical architectures consisting of many rhombic building units exhibit high specific surface area. Electrorheological (ER) properties of hierarchical hollow TiO2-based suspension were investigated under steady and oscillatory shear. The hollow TiO2-based suspensions show much higher yield stress and elasticity than pure TiO2 suspension at the same electric field strength. This phenomenon was elucidated well in view of their dielectric spectra analysis. The sea urchin-like architectures result in stronger interfacial polarization of hollow TiO2 suspension upon an electric field, showing higher ER activity. Also, hollow i...

British Library Electronic Table of Contents (United Kingdom)

The physicochemical properties of binary lipid mixtures of diether C25,25 lipids and dipalmitoyl-L-a-phosphatidylcholine (DPPC) were studied using photon correlation, fluorescence and electron paramagnetic resonance spectroscopy, and transmission electron microscopy. These two types of lipids can be mixed at all molar ratios to form unilamellar and multilamellar liposomes. Fluorescence anisotropy of 1,6-diphenyl-1,3,5-hexatrien in mixed liposomes indicates that the abrupt changes in order parameter in the hydrophobic part of bilayer membranes made of DPPC lipids disappears with increasing mol%C25,25 lipids. Electron paramagnetic resonance spectroscopy shows that at temperatures below 50^oC, the interfacial regions of membrane bilayer of mixed liposomes is more fluid than for pure DPPC lipo...

Energy Technology Data Exchange (ETDEWEB)

The propagation of acoustic pressure perturbations in an adiabatic low-quality air/water flow were investigated both theoretically and experimentally. A linearized dispersion model is correlated with data to extract information on the behavior of interfacial momentum transfer controlled by the virtual volume coefficient. The dispersion model is examined in limiting cases of low and high frequency and related to current models for critical flow velocity. Fourier decomposition techniques are employed to predict the dispersion of measured pressure pulses and to relate data for standing waves and propagating pulses. The dispersion model is based on a two-fluid model and is the most complete model available in the literature at this time. The dispersion data presented herein is also the best available to date for low frequency (i.e., frequencies less than bubble resonance) sound propagation in bubbly air/water mixtures.

British Library Electronic Table of Contents (United Kingdom)

A novel composite charged mosaic membrane (CCMM) was prepared via interfacial polymerization (IP) of polyamine [poly(epichlorohydrin amine)] and trimesoyl chloride (TMC) on the polyethersulfone (PES) support. Fourier transform infrared spectroscopy (FT-IR), environmental scanning electron microscopy (ESEM), atomic force microscopy (AFM) and water contact angle analysis were applied to characterize the resulted CCMM. The FT-IR spectrum indicates that TMC reacts sufficiently with polyamine. ESEM and AFM pictures show that the IP process produces a dense selective layer on the support membrane. The water contact angle of the CCMM is smaller than that of the substrate membrane because of the cross-linked hydrophilic polyamine network. Several factors affecting the IP reaction and the performan...

Energy Technology Data Exchange (ETDEWEB)

Application of an optimization technique to extract the non-ideal parameters of gas absorption with chemical reactions process was described. The gas absorption was modeled using mass transfer theory to represent the realistic behaviors of an absorber. The model was a highly non-linear iterative model which correlated the overall rate of absorption as the function of unknown non-ideal parameters, including the physical liquid mass transfer coefficient and the wetted interfacial area of of packings. The optimization program was developed to minimize the sum of squares of relative errors between the model predictions and the experimental data. Four sets of experimental data (case studies) with different operating conditions were used for extracting parameters. Comparisons between predicted and experimental measured overall absorption rate were in good agreement, average absolute value of relative errors not exceeding 5.4 %. 18 refs., 3 tabs., 4 figs.

British Library Electronic Table of Contents (United Kingdom)

Thin films of Ni and Ni alloy have been widely used in microelectromechanical systems (MEMS) and magnetic storage systems. As the dimensions of components in these systems decrease to the micro-scale, even the nano-scale, the interfacial phenomena significantly differ to the counterparts on the macro-scale. A better understanding of micro-/nano-tribology will benefit the fabrication of the small components. In this manuscript parallel molecular dynamics (MD) simulations have been conducted to investigate the nanoscratch behavior of nickel. The simulations are performed for two cases with different indenter shapes. Case I has a sharp indenter, while the indenter in Case II is blunt. It has been found that the indenter shape significantly influences the nanoscratch deformation. The sharp ind...

Energy Technology Data Exchange (ETDEWEB)

The interfaces between metal electrodes and electroactive organic materials are important for the performance of organic electronic devices. One way of optimizing the anode/organic interface is the insertion of a (sub-)monolayer of molecular acceptors. Here we present an UPS study of new electron acceptor molecules deposited on Au(111), Cu(111) and Ag(111). This study intends to improve the understanding of how the interactions of specific electron withdrawing groups with metal surfaces are correlated with observed modifications of interfacial electron density distribution, work function change ({delta}{phi}), and the energy level alignment. We find that {delta}{phi}, which is the difference between the work function ({phi}) of the clean metal surface and {phi} after formation of a molecular monolayer, is a monotonic function of initial {phi} of the metal. Two different slopes were observed for acceptors with cyano and those with keto or nitro groups.

British Library Electronic Table of Contents (United Kingdom)

The interlayer exchange coupling between Co/Pt perpendicular-to-plane magnetized layers across a thin IrMn spacer layer was experimentally studied. In contrast to earlier studies on interlayer coupling through antiferromagnetic NiO, which revealed an oscillatory coupling behavior as a function of NiO thickness, a ferromagnetic coupling was observed here in the range of IrMn thickness between 0.6 and 1.5nm and antiferromagnetic between 1.5 and 2.5nm. The antiferromagnetic coupling is attributed to an orange peel magnetostatic mechanism whereas the ferromagnetic coupling is attributed to an out-of-plane polarization of the antiferromagnetic IrMn layer induced by the interfacial exchange interaction with the adjacent out-of-plane ferromagnetic layers. Measurements of hysteresis loops versus t...

Energy Technology Data Exchange (ETDEWEB)

This is the final report of a three-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). The primary aim of this project is to obtain a basic scientific understanding of electrical transport processes at interfaces that contain an organic electronic material. Because of their processing advantages and the tunability of their electronic properties, organic electronic materials are revolutionizing major technological areas such as information display. We completed an investigation of the fundamental electronic excitation energies in the prototype conjugated polymer MEH-PPV. We completed a combined theoretical/experimental study of the energy relation between charged excitations in a conjugated polymer and the metal at a polymer/metal interface. We developed a theoretical model that explains injection currents at polymer/metal interfaces. We have made electrical measurements on devices fabricated using the conjugated polymer MEH-PPV a ...

Energy Technology Data Exchange (ETDEWEB)

The microstructure of the interphase in semicrystalline polymer matrix composites has a dramatic influence on their mechanical properties. Studies have been performed to alter this region and to correlate various interphase morphologies with changes in fiber-matrix adhesion. A reinforced nylon 66 composite, when subjected to specific thermal histories, contains an interphase composed of transcrystallinity. This region has been altered by coating fibers with a diluent, poly(vinyl pyrrolidone), and/or adding the diluent to the matrix material in very small quantities. Interphase morphology was investigated with optical microscopy, and adhesion was measured using a modified fiber pull-out test. It was found that transcrystallinity increases the interfacial shear strength. The effect different interphase morphologies have on the durability of bulk composite samples is currently under investigation.

British Library Electronic Table of Contents (United Kingdom)

The investigation of steam, water, and air flow characteristics in horizontal channel is a part of major investigations program at the Lithuanian Energy Institute. The objective of this program is to identify condensation effects on two-phase flow stability and to predict conditions when rapid condensation could be induced in two-phase condensable flow. This article presents investigation of steam-water and air multiphase flow in nearly horizontal rectangular channel. The experimental data for pressure drop and interfacial and wall shear stresses in the channel with uniform distribution of void fraction are presented in this paper. Overall channel dimensions are length = 1.2 m, width = 0.02 m, height = 0.1 m; however, the test section was about 0.84 m in length. Three different flow types ...

Energy Technology Data Exchange (ETDEWEB)

It is well known that a protective film is formed on the graphite negative electrode in ethylene carbonate (EC) electrolyte solution. This film is lithium-ion conductive and protects the decomposition of the electrolyte solution. In the present paper, the electrode/electrolyte interfaces in lithium-ion rechargeable batteries were characterized by three-dimensional complex impedance plots, whose axes are real, imaginary parts and time. The film resistance R {sub sei} and charge transfer resistance R {sub ct} were determined for negative electrodes in EC/ethyl methyl carbonate (EMC) electrolyte solution, and the formation mechanisms of the interfacial film were discussed. Furthermore, the contributions of vinylene carbonate and ethylene sulfite, which are added into the electrolyte solution for the film formation, were investigated.

British Library Electronic Table of Contents (United Kingdom)

Abstract Therapeutic proteins are exposed to various potential contact surfaces, particles, and leachables during manufacturing, shipping, storage, and delivery. In this review, we present published examples of interfacial- or leachable-induced aggregation or particle formation, and discuss the mitigation strategies that were successfully utilized. Adsorption to interfaces or interactions with leachables and/or particles in some cases has been reported to cause protein aggregation or particle formation. Identification of the cause(s) of particle formation involving minute amounts of protein over extended periods of time can be challenging. Various formulation strategies such as addition of a nonionic surfactant (e.g., polysorbate) have been demonstrated to effectively mitigate adsorption-i...

British Library Electronic Table of Contents (United Kingdom)

Pitch-based short carbon fibers (CFs) were treated by air oxidation and cryogenic nitrogen, respectively. Thereafter the treated and untreated CFs were incorporated into polyimide (PI) matrix to form composites. The CFs before and after treatment were examined by XPS and SEM.The flexural strength of the specimen was determined in a three-point test machine and the tribological properties of PI composites sliding against GCr15 steel rings were evaluated on an M-2000 model ring-on-block test rig. The results show that the surface of the treated CFs became rougher. Lots of active groups formed on the CF surface after air oxidation.The treatment can effectively improve the mechanical and tribological properties in their PI composites due to the enhanced fiber-matrix interfacial bonding. Copyri...

Energy Technology Data Exchange (ETDEWEB)

Wood polymer composite (WPC) specimens were produced by impregnating a tropical wood with methyl methacrylate and subsequently polymerised by ..gamma..-irradiation. Beam specimens of varying weight percentages of polymer were then subjected to a three point bend creep test under a constant load condition, for 250, 300 and 350 N. A Norton-Bailey (power law) mathematical model was used to describe the creep behavior, with the creep components determined by a nonlinear regression analysis. Significant creep improvements were obtained from the composite specimens as compared to the untreated wood specimens. Results indicated that maximum creep resistance is obtained when the amount of polymer loading exceeded 30%. An interfacial interaction between the polymer and the wood cell wall was used to account for the behavior of the increase in the creep resistance.

Energy Technology Data Exchange (ETDEWEB)

Fundamental phenomena of condensation heat transfer at a steam-water interface have been studied related to the thermo-hydrodynamics of the emergency core cooling system for light water reactors. In this study temperature fluctuations near the interface and in the liquid phase were measured using fine thermocouples for a saturated steam-subcooled water co-current stratified two-phase flow in a nearly horizontal rectangular channel, and heat transfer coefficients were determined experimentally. The values of the condensation heat transfer coefficients in this experiment are from 6 to 40 kW/m{sup 2}K. In the regions of high Reynolds numbers, as the steam Reynolds numbers become larger, the average interfacial heat transfer coefficients tend to increase. The corelations of Nusselt numbers were obtained from the heat transfer data. (author)

British Library Electronic Table of Contents (United Kingdom)

Ultrasonic gold and aluminum wire wedge bonding are widely used for electrical and signal interconnections of the integrated circuit chip packages. In this paper, based on the metallurgical theories and thermal aging test methods, the long-term thermal reliabilities of gold and aluminum wire wedge bonding on aluminum and Au/Ni/Cu pads, were investigated, respectively. At 200degreeC, the Au/Al bond interfaces evolved little when the storage time was less than 48h; with the aging time increasing, the interfacial intermetallic compounds (IMC) grew up from the pad (vertical growth); the primary compounds were Au5Al2 near the bond toe and heel, and Au2Al at the periphery. Then, the thickness of IMC was unchanged, and extended horizontally (lateral growth), Au5Al2 transformed into more stable Au...

British Library Electronic Table of Contents (United Kingdom)

Wood plastic composites (WPCs) are comprised of wood flour and thermoplastic polymer. The matrix is typically high-density polyethylene, poly (vinyl chloride), or polypropylene. The effect of morphology and micromechanics of wood flour particles on the mechanical performance of the bulk composite is a relatively unexplored area. The knowledge about the in situ properties of wood particles and the interfacial properties between the wood particles and the polymer matrix in the bio-composites is very limited. The objective of this work is to characterize the full-field deformation and strain distribution in and around wood particles embedded in polymer matrix. The mechanical tests are performed in small-scale tensile loading stage on thin composite samples containing 1-3 wood particles orient...

International Nuclear Information System (INIS)

Ultra-shallow junction formation in deep submicron Si devices is limited by anomalous diffusion of the dopant, which is related to the release of interstitials from defect clusters formed during the implantation of energetic ions or the subsequent annealing. The work described in this dissertation is concerned with the effects of low energy B ion implantation, especially damage formation, clustering and its annealing. After a review of the stopping and ranges of energetic ions in Si, the formation of implant damage, in particular of point defects, their migration, agglomeration and annihilation, including the involvement of dopant ions, is considered. A description of the Salford ultra low energy implanter is given and the main analysis technique, medium ion energy scattering (MEIS) reviewed. Additional analytical techniques used, such as secondary ion mass spectrometry (SIMS), 4-point probe and cross section transmission microscopy (XTEM) as well as TRIM simulation are briefly ...

Energy Technology Data Exchange (ETDEWEB)

The article provides a 1998 updated picture of Italy's and the world's photovoltaic market in terms of produced modules and total installed capacity, as well as market growth forecasts up to 2010. After a short description of the state-of-the-art of cell and module manufacturing, ana analysis of the cost of producing a photovoltaic kw is reported for different plant types: stand-alone plants with energy storage batteries, plants connected to low low voltage networks or intended for supporting medium voltage networks, hybrid plants with diesel sets. The article is concluded by illustrating ENEL's (Electric Power Production Company) engagement in the field of photovoltaic solar energy as regards theoretical studies, research and testing of new technologies, and installing plants; over nearly twenty years of activity, ENEL has designed and built a few hundreds of photovoltaic plants for a total capacity of about 4.000 kw, and is currently in the process of ...

Energy Technology Data Exchange (ETDEWEB)

Amorphization and a dual implant technique have been used to manipulate residual defects that persist following implantation and post-implant thermal treatments. Residual defects can often be attributed to ion-induced defect excesses. A defect is considered to be excess when it occurs in a localized region at a concentration greater than its complement. Sources of excess defects include spatially separated Frenkel pairs, excess interstitials resulting from the implanted atoms, and sputtering. Preamorphizing prior to dopant implantation has been proposed to eliminate dopant broadening due to ion channeling as well as dopant diffusion during subsequent annealing. However, transient-enhanced diffusion (TED) of implanted boron has been observed in pre-amorphized Si. The defects driving this enhanced boron diffusion are thought to be the extended interstitial-type defects that form below the amorphous-crystalline interface during implantation. A dual implantation process was applied in an ...

Energy Technology Data Exchange (ETDEWEB)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr{sub 2}N, CrN, TiN, V{sub 2}N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of scale-up studies to determine the feasibility of extending the nitridation approach to thin 0.1 mm stainless steel alloy foils for proton exchange membrane fuel cell (PEMFC) bipolar plates. Developmental Fe-20Cr-4V alloy and type 2205 stainless steel foils were treated by pre-oxidation and nitridation to form low-ICR, corrosion-resistant surfaces. As-treated Fe-20Cr-4V foil exhibited target (low) ICR values, whereas 2205 foil suffered from run-to-run variation in ICR values, ranging up to 2 x the target value. Pre-oxidized and nitrided surface structure examination revealed surface-through-layer-thickness V-nitride particles for the treated Fe-20Cr-4V, but ...

Energy Technology Data Exchange (ETDEWEB)

The two-phase flows involve interfacial interactions which modify significantly the structure of the mean and fluctuating flow fields. The design of the two-fluid models adapted to industrial flows requires the taking into account of the effect of these interactions in the closure relations adopted. The work developed in this thesis concerns the development of first order two-fluid models deduced by reduction of second order closures. The adopted reasoning, based on the principle of decomposition of the Reynolds stress tensor into two statistically independent contributions turbulent and pseudo-turbulent parts, allows to preserve the physical contents of the second order relations closure. Analysis of the turbulence structure in two basic flows: homogeneous bubbly flows uniform and with a constant shear allows to deduce a formulation of the two-phase turbulent viscosity involving the characteristic scales of bubbly turbulence, as well as an analytical description ...

Energy Technology Data Exchange (ETDEWEB)

The latest inclined mine winder started operation in April, 1995 at the Kushiro Mining Station of Taiheiyo Coal Mining Co. A permanent magnet synchronous motor, a cycloconverter, and H{sub {infinity}} control are employed to complete the latest inclined mine winder. The winder is the world`s longest and fastest inclined mine winder, and the torque of the permanent magnet synchronous motor is the largest in the world. A report is made on the driving system placing emphasis on the points considered in the design. The gallery has the length of world`s longest 6,626m and the average gentle inclination of 6 degree. The worker transport car runs at the world`s fastest speed of 420m/min from the mouth to the bottom of the pit, making a round trip in 40 minutes. Speed is adjusted smoothly by the cycloconverter, and the car arrives at the destination safely in a short time due H{sub {infinity}} controlling. By the application of H{sub {infinity}} control, the tension of the ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents a technique for speed control three-phase induction motor using the pulse width modulation (PWM), in open loop while maintaining the tension for constant frequency. The technique is adapted from a thesis entitled 'Control of the three-phase induction motor, using discrete PWM generation, optimized and synchronized', where studies are presented aimed at their application in home appliances, to eliminate mechanical parts, replaced by low cost electronic control, thus having a significant reduction in power consumption. Initially the experiment was done with the Intel 80C31 micro controller. In this paper, the PWM modulation is implemented using a PIC micro controller, and the speed control kept a low profile, based on tables, synchronized with transitions and reduced generation of harmonics in the network. Confirmations were made using the same process of building tables, but takes advantage of the program of a RISC device.

Science.gov (United States)

The Wind Energy Research Division of Sandia National Laboratories has been funded by the Wind/Ocean Technology Division of the Department of Energy (DOE) to design and build a 34-meter diameter Vertical Axis Wind Turbine (VAWT). The turbine design incorporates the results of recent VAWT research in aerodynamics and structural dynamics. Initial system concept studies identified several blade options that met the required power rating of 500 kW. The final blade and rotor configurations were chosen based on finite element calculations that determined the turbine modes of response, their frequency of vibration, and stress levels. For parked survival turbine components were designed to with stand the loading of a 150 mph (67.0 m/s) wind coupled with maximum cable tensions. Specific areas of design discussed include the rotor, cables, bearings, brakes, and foundations. Construction of the turbine is in progress at this time and anticipated completion of the project is ...

Energy Technology Data Exchange (ETDEWEB)

Security of supply is defined as the availability and reliability of energy supply at acceptable prices. By security of energy supply we mean a globally large supply of reliable, affordable, clean energy. By virtue of its nature security of supply in the energy sector primarily requires making provisions for the future through exploration, innovation, research, diversification and investments in technology. Energy politics takes place in a tension field defined by the goals of economic efficiency, sustainability and security of supply. In the past there have been repeated shifts within this triad of goals. The task for a rational energy policy is to reconciliate these goals in a meaningful way. European energy policy is understood to comprise all sovereign measures taken by the European Union in the energy sector, in particular measures that impact on the supply and demand for energy resources. Energy law serves, or should serve, to bring energy policy to ...

CERN Document Server

We present a phenomenological analysis of the recent Tevatron results on the $t \\bar t$ forward-backward asymmetry and invariant-mass spectrum assuming a new contribution from an s-channel gluon resonance with a mass in the range from 700 to 2500 GeV. In contrast to most of the previous works, this analysis shows that for masses below ~1 TeV resonant New Physics could accommodate the experimental data. In general, we find that axial-like couplings are preferred for light and top quark couplings, and that only top quark couples strongly to New Physics. We find that composite model scenarios arise naturally from only phenomenological analyses of the experimental results. We show that our results are compatible with recent LHC limits in dijet and $t \\bar t$ production, and find some tension for large resonance mass ~2.5 TeV. We indicate as best observables for discriminating a relatively light new gluon a better resolution in CDF forward-backward asymmetry, as well ...

Science.gov (United States)

The effects of 0.2 and 0.5 mL/kg Innovar (a neuroleptic analgesic) on cardiovascular functions and reflexes in rabbits were measured. We recorded the effects of Innovar on arterial pressure, heart rate, respiration rate, ventricular contractility, arterial oxygen tension, as well as the drug's effects on the bradycardia and vasoconstrictor response to cigarette smoke stimulation of the nose (the so-called "nasopharyngeal reflex"). In animals given 0.2 mL/kg Innovar, all steady state cardiovascular variables had returned to pre-Innovar levels in 45 min, as had the efficacy of the nasopharyngeal reflex. In animals given 0.5 mL/kg Innovar, all steady state cardiovascular variables, except PaO2, were slightly but significantly depressed for up to 135 min after injection. The nasopharyngeal reflex returned to normal within 90 min. Because of the calmative and analgesic effects of Innovar, and its only moderate effects on cardiovascular functions and reflexes, we feel it ...

International Nuclear Information System (INIS)

A 2007 report compiled by members of the armed services indicates that climate change presents a serious security threat to the American public as well as to United States military operations. It is likely that climate change will increase global tensions and competition for resources. This presentation discussed advanced research and technology programs conducted by the National Aeronautics and Space Administration (NASA). Scientists and engineers at NASA have developed a number of technologies that may contribute to American energy security. Advanced energy research and development programs initiated by the organization include advanced heat engines; wind turbines; batteries and electric cars; solar photovoltaics; and fuel cell technologies. NASA's aeronautics and space exploration program has several capabilities relevant to advanced wind power systems. A collaborative program is currently underway to develop airborne wind turbines designed to harness high ...

British Library Electronic Table of Contents (United Kingdom)

RESUME: Cet article propose une tude du r le croissant que joue l valuation dans la gouvernance des services domicile en Europe. L introduction de quasi march s dans plusieurs pays europ ens va de pair avec un processus d autonomisation de la fonction d valuation qui devient un v ritable outil de r gulation de la concurrence. Une analyse compar e des situations en Belgique, France et Royaume Uni, tant de la demande que de l offre de services, met en vidence les tensions r currentes dans les objectifs de l valuation (qualit des services, ma trise des budgets sociaux, cr ation d emploi), la faible prise en compte de la qualit de l emploi ainsi que les limites des dispositifs standardis s d valuation au regard de la rh torique du libre choix de l usager (consommateur).

Energy Technology Data Exchange (ETDEWEB)

This study deals with a research field started at the LFI (Laboratorio de Fabricacion Integrada) of the ULPGC (Universidad de Las Palmas de Gran Canaria). Its aim is to analyse and propose improvements in the electroformed nickel cores manufacture. The main application of these cores is to be used as plastic injection molds. It has been considered an important part of this study taking under consideration internal stresses that appear in the nickel electroformed core. These stresses play a determinant role towards reaching a dimensional and resistant quality standard of the shells, which will be later transformed into cores. The investigation includes not only a theoretic study but also an experimental one. the testing method has the remarkable advantage of a wide industrial application because of its simplicity, low cost and reproducibility of the electrolytic bath actual conditions. (Author) 7 refs.

International Nuclear Information System (INIS)

Hole mobility changes under uniaxial and combinational stress in different directions are characterized and analyzed by applying additive mechanical uniaxial stress to bulk Si and SiGe-virtual-substrate-induced strained-Si (s-Si) p-MOSFETs (metal-oxide-semiconductor field-effect transistors) along (110) and (100) channel directions. In bulk Si, a mobility enhancement peak is found under uniaxial compressive strain in the low vertical field. The combination of (100) direction uniaxial tensile strain and substrate-induced biaxial tensile strain provides a higher mobility relative to the (110) direction, opposite to the situation in bulk Si. But the combinational strain experiences a gain loss at high field, which means that uniaxial compressive strain may still be a better choice. The mobility enhancement of SiGe-induced strained p-MOSFETs along the (110) direction under additive uniaxial tension is explained by the competition between biaxial and shear stress.

Energy Technology Data Exchange (ETDEWEB)

This document presented the results of a full-scale pile load tests conducted on helix pile foundations supporting power transmission towers in northern Manitoba. The site conditions were described along with pile installation and the performance of the foundations. The pile load tests were carried out in 2 different soil conditions, notably soft to firm clays and stiff high plastic clays with silt varves. The performance of the helix pile foundations were examined under axial compressive and axial tension (uplift) loading conditions. The results of the compressive load tests were presented in the form of load settlement curves while the results of the uplift load tests were presented in the form of load displacement curves. Both types of load tests in soft or stiff clays showed the suitability of helical pile foundations for power transmission lines in northern Manitoba. The cylindrical shear failure mechanism controlled the behaviour of helical piles. The helical ...

Energy Technology Data Exchange (ETDEWEB)

A 200 ft. tall stack, consisting of a concrete chimney with an independent acid proof brick liner built in the 1950`s, serving the Separations facility at the Savannah River Site (SRS), was evaluated for the performance category 3 (PC3) level of Natural Phenomena Hazards (NPH) effects. The inelastic energy absorption capacity of the concrete chimney was considered in the evaluation of the earthquake resistance, in particular, to compute the F{sub {mu}} factor. The calculated value of F{sub {mu}} exceeded 3.0, while the seismic demand for the PC3 level, using an F{sub {mu}} value of 1.5, was found to be less than the capacity of the concrete chimney. The capacity formulation of ACI 307 was modified to incorporate the effect of an after design opening on the tension side. There are considerable uncertainties in determining the earthquake resistance of the independent brick liner. The critical liner section, located at the bottom of the breeching opening, does not ...

International Nuclear Information System (INIS)

Human hair fibers experience tensile forces during grooming and styling processes. The tensile response of hair is hence of considerable interest to the cosmetics industry. In this study, in situ tensile characterization studies have been carried out in an atomic force microscope (AFM) on different hair under different conditions. A custom-built AFM sample stage allows hair fibers to be loaded in tension. A technique to locate and image the same control area at different strains has been developed to study the changes in morphology that occur with deformation. Virgin Caucasian, Asian and African hair were studied to understand the differences between different ethnic hair types. Also, the tensile response and morphological changes of virgin, chemically damaged and conditioner-treated Caucasian hair after soaking were compared against the corresponding dry tensile response. Finally, virgin, damaged and treated Caucasian hair fibers were subjected to fatigue cycling ...

Energy Technology Data Exchange (ETDEWEB)

Implementation of Noble Metal Chemical Application (NMCA) in a Boiling Water Reactor (BWR) requires injection of a noble metal compound while the reactor is idle at hot shutdown conditions. In order to minimize outage time, utilities are very pro-actively finding ways to reduce the number of critical path tasks. One of these tasks is to remove some containment vessel drywell head bolts during the NMCA idle time. This, thereby, saves the utilities outage time, or they can perform other tasks as desired. Using design basis conditions and state-of-the-art analytical techniques, detailed finite element stress analyses of the closure region are performed. Two acceptance criteria are evaluated. The first is that contained within Section III of the ASME Code for allowable stresses. The second relates to leak tightness, i.e., with bolt removal the joint must still remain leak tight. This paper describes the activities performed to justify bolt removal during the noble metal compound injection ...

Science.gov (United States)

A hypotheses that mitoxantrone is a competitive antagonist at muscarinic cholinergic receptors was examined in guinea-pig hearts. In isolated left atrial muscle preparations, electrically paced at 2 Hz, the muscarinic agonist, carbachol, caused a concentration-dependent decrease in developed tension. Mitoxantrone caused a parallel right-ward shift of the concentration-response curve for carbachol. Schild plots for the effect of mitoxantrone on the carbachol concentration-response relationship were linear with a slope of 0.88 which was not significantly different from the unity. The right-ward shift of the carbachol concentration-response relationship by mitoxantrone significantly reversed after an additional incubation with a mitoxantrone-free solution, although the reversal was incomplete after a 2-h incubation in the mitoxantrone-free solution. Mitoxantrone caused a concentration-dependent displacement of specific [3H]quinuclidinyl benzilate binding to membrane ...

International Nuclear Information System (INIS)

Hybrid organic-inorganic coatings with phosphonate functionalities have been synthesized and evaluated as prospective surface treatments for magnesium materials. These coatings have been processed via a sol-gel route by hydrolysis and condensation of a mixture of diethylphosphonatoethyltriethoxy-silane and tetraethoxy-silane with variable molar ratios. The coatings morphology and the surface chemistry at the coating/substrate interface have been characterized using scanning electron microscopy, X-ray photoelectron spectroscopy, "3"1P nuclear magnetic resonance spectroscopy, and time-of-flight secondary ion mass spectrometry. The corrosion protection performance of the coatings deposited on magnesium alloy AZ31B has been examined by a group of electrochemical techniques including potentiodynamic polarization and electrochemical impedance spectroscopy. In addition, a scanning Kelvin probe technique has been used to investigate interfacial properties of the coatings. ...

British Library Electronic Table of Contents (United Kingdom)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr2N, CrN, TiN, V2N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited...

Energy Technology Data Exchange (ETDEWEB)

The reactions between (100) GaAs and the near-noble metals Ni, Pd, and Pt have been investigated by application of high-resolution transmission electron microscopy (TEM), energy-dispersive analysis of x rays in the scanning TEM and Rutherford backscattering spectrometry. Emphasis is placed on the evolution of the phase distributions, film compositions, and interface morphologies during annealing at temperatures up to 480 /sup 0/C. The first phase in the Ni/GaAs reaction is shown to have the nominal composition Ni/sub 3/GaAs. Ternary phases of the type Pd/sub x/GaAs are also found to be the dominant products of the Pd/GaAs reaction. Conversely, only binary phases result from the Pt/GaAs reaction. These observations are used to construct isothermal sections of the M--Ga--As thin-film phase diagrams. The behavior of a thin (1--2 nm) native oxide--hydrocarbon layer during the Ni/GaAs, Pd/GaAs, and Pt/GaAs reactions is also investigated. Only the Ni/GaAs reaction is noticeably impeded in ...

Energy Technology Data Exchange (ETDEWEB)

An experiment was conducted on the structure of mesoscopic calculating method for cement-based composite materials. The purpose was utilization for the simulation of mesoscale failure processes and the development of new composite materials. Mesh split based on Voronoi polygons was applied as the discrete limit analysis of the cement-based composite materials containing aggregate particles taking the arrangement of random particles into consideration, and a two-dimensional rigid-body/spring model was employed as the model. The nonhomogeneity of concrete was represented by three kinds of different spring parameters which were aggregate, mortar matrix and their interfaces. The simulation results were summarized as follows: The stress-strain curve went into a non-linear state from the 30% of the maximum stress. The generation of interfacial crack started on the side of the aggregate, but the propagation of the crack was stable. Deformation became unstable at 80% of ...

Energy Technology Data Exchange (ETDEWEB)

The effective electron mobility was measured as a function of surface field in polysilicon thin film transistors having the following three types of gate dielectrics; silicon dioxide deposited by low temperature (350degC) plasma-enhanced chemical vapor deposition (PECVD), low temperature (400degC) nitrogen-rich PECVD silicon nitride and high temperature (1050degC) thermally grown silicon dioxide. At low surface fields, the maximum true effective electron mobility was 40[+-]3 cm[sup 2] V[sup -1] s[sup -1] in all devices independent of the type of gate dielectric, indicating that the quality of the interface is the same. However, at high surface fields a stronger degradation of the mobility was observed in devices having the thermally grown silicon dioxide as gate dielectric, indicating the presence of surface roughness within the interfacial region. The polysilicon structure was studied by transmission electron microscopy in order to ensure that our electrical ...

Energy Technology Data Exchange (ETDEWEB)

Chromium electroplated AISI 316L stainless steel was nitrided using inductively coupled plasma (ICP) for application in the bipolar plate of a polymer electrolyte membrane fuel cell (PEMFC). A continuous and thin chromium nitride layer was formed at the surface of the samples after ICP nitriding for 2 h at 400 C. The interfacial contact resistance (ICR) and corrosion resistance in simulated PEMFC operating conditions were higher than the required values, while they varied with the applied dc bias voltage during the nitriding process. The ICR value decreased with an increase in bias voltage. Potentiodynamic polarization measurements showed that all of the nitrided samples had excellent corrosion resistance with a current density of {proportional_to}10{sup -7} A cm{sup -2} at the cathode. It was also found that the oxygen content at the surface was not increased after the corrosion test. X-ray diffractometry (XRD), field emission scanning electron microscopy ...

International Nuclear Information System (INIS)

In situ spectroscopic ellipsometry was employed to investigate the initial regime of rare earth metal (REM) conversion coatings formation on AZ31 magnesium alloy. Three REM salts solutions, 0.05 mol.dm"-"3 Ce(NO_3)_3, La(NO)_3 and Sm(NO)_3 solutions, were used for REM conversion coatings preparation. By deconvoluting the ellipsometric data, the surface of the fresh well-polished AZ31 magnesium alloy was found to be covered with 15.80 nm thick native (hydr)oxide film; the refractive indices and the thickness of Ce, La and Sm conversion coatings were obtained. The formation kinetics of three REM coatings follows different exponential functions and the coatings exhibit different optical properties. La conversion coating has the largest n values and the lowest k values while Sm conversion coating is just opposite. Moreover, the pH variation of the bulk conversion solutions upon the coatings formation was recorded. It is confirmed that the reduction of protons leads to the ...

Energy Technology Data Exchange (ETDEWEB)

The {beta}-Si{sub 3}N{sub 4}w/6061 Al composite was fabricated by the squeeze casting and extruded with the extrusion ratios of 44 and 100 at 773 K. Its tensile strength and superplastic characteristics were investigated and the following results were obtained: (1) the {beta}-Si{sub 3}N{sub 4}w/6061 Al composite exhibits the tensile strengths of about 400 MPa at room temperature and of about 250 MPa at 773 K; (2) the m value of the composite pulled at 818 K is 0.33 in the strain rate range from 0.02 up to 1.0 s{sup {minus}1}; (3) the total elongation of the composite becomes about 173 % at the strain rate of 0.02 s{sup {minus}1} even in the case of the high volume fraction of 0.25; (4) no reaction product on the surface of {beta}-Si{sub 3}N{sub 4} whisker after removing a matrix by etching was detected except AlN; (5) the fracture surface of the composite includes the melt matrix and small filaments, which shows that interfacial sliding should promote HSRS in ...

Energy Technology Data Exchange (ETDEWEB)

Nitridation of Cr-bearing alloys can yield low interfacial contact resistance (ICR), electrically- conductive and corrosion-resistant CrN or Cr2N base surfaces of interest for a range of electrochemical devices, including fuel cells, batteries, and sensors. This paper presents results of exploratory studies of the nitridation of two high Cr (30-35 wt%) commercially available Ni-Cr alloys and a ferritic high Cr (29 wt.%) stainless steel for proton exchange membrane fuel cell (PEMFC) bipolar plates. A high degree of corrosion resistance in sulfuric acid solutions designed to simulate bipolar plate conditions and low ICR values were achieved via nitridation. Oxygen impurities in the nitriding environment were observed to play a significant role in the nitrided surface structures that formed, with detrimental effects for the Ni-Cr base alloys, but beneficial effects for the stainless steel alloy. Results of single-cell fuel cell testing are also presented.

Energy Technology Data Exchange (ETDEWEB)

The electrode kinetics for oxygen reduction on conducting metal oxides, including lithiated NiO (formed in situ) and Sb-doped SnO/sub 2/, have been investigated. Kinetic measurements were carried out by using ac impedance and coulostatic relaxation methods. The ac behavior on the oxide electrodes was analyzed on the basis of a modified Randles-Ershler type equivalent circuit which takes into account the effect of non-faradaic components due to the semiconducting oxide films. The kinetic parameters (the charge transfer resistance and Warburg coefficient) and the interfacial parameters (the double layer capacity, film capacity and film resistance) were obtained by a least squares curve fitting method under P/sub O2//P/sub CO2/=0.9/0.1 atmosphere. The exchange current density was found to be 10 to 20 mA cm/sup -2/ at the oxide electrodes, assuming n=2. The coulostatic relaxation experiments supported the magnitude of the i/sub o/ values.

Energy Technology Data Exchange (ETDEWEB)

The prediction of two-phase flow regime in the horizontal pipings during a loss-of-coolant accident (LOCA) is important for safety analysis of a pressurized water reactor (PWR). The flow regime transition conditions for a horizontal two-phase air-water flow were studied using a large-height, horizontal rectangular duct test section. The duct dimensions were 700 mm in height, 100 mm in width and 28.3 m in length. The experimental criterion for the flow regime transition from the stratified to slug flow regimes, in terms of the local void fraction and the non-dimensional gas-liquid relative velocity, agreed qualitatively with the prediction by the Mishima-Ishii model that is based on an idea that the interfacial waves with the largest growth rate will develop into a slug. However, the transition in the experiment occurred at systematically lower (by about 40 %) relative velocities than the prediction by the Mishima-Ishii model. Therefore, an experimental correlation ...

International Nuclear Information System (INIS)

The nature of the electrolyte strongly influences the electrode kinetics of the oxygen evolution reaction (OER) and electrochemical ozone production (EOP) mainly by affecting the degree of coverage by the intermediates of both processes. The anomalous behaviour of the Tafel coefficient, b, as a function of temperature was attributed to surface adsorption of the electrolyte species, and the competition between them, as well as gas bubble adherence. Comparison of the current efficiencies of the EOP, PHI_E_O_P, determined for different temperatures and supporting electrolyte compositions, showed the presence of fluorinated anions increases PHI_E_O_P. The influence of the anion nature on PHI_E_O_P, when analysed in the light of the proposed electrode mechanism, reveals introduction into the electrolyte of anions having a high electronegativity changes the double layer structure resulting in an increase of surface concentration of the active centres leading to EOP. The inhibition of the OER ...

Energy Technology Data Exchange (ETDEWEB)

A dense and supersaturated nitrogen layer with higher conductivity is obtained on the surface of austenitic stainless steel 304L by the low temperature plasma nitriding. The effect of plasma nitriding on the corrosion behavior and interfacial contact resistance (ICR) for the austenitic stainless steel 304L was investigated in 0.05M H{sub 2}SO{sub 4}+2ppm F{sup -} simulating proton exchange membrane fuel cell (PEMFC) environment using electrochemical and electric resistance measurements. The experiment results show that the stable passive film is formed after the potentiostatic polarization at the specified anodic or cathodic potentials under PEMFC operation condition, and the plasma nitriding improves slightly the corrosion resistance and decreases markedly the ICR of 304L. The ICR of the plasma nitrided 304L increases after the potentiostatic polarizations for 4h, and lower than 100m{omega}cm{sup 2} at the compaction force of 150Ncm{sup -2}. (author)

Energy Technology Data Exchange (ETDEWEB)

We demonstrate tuning of Schottky energy barriers in organic electronic devices by utilizing chemically tailored electrodes. The Schottky energy barrier of Ag on poly[2-methoxy], 5-(2{prime}-ethyl-hexyloxy)- 1,4-phenylene was tuned over a range of more than 1 eV by using self-assembled monolayers (SAM{close_quote}s) to attach oriented dipole layers to the Ag prior to device fabrication. Kelvin probe measurements were used to determine the effect of the SAM{close_quote}s on the Ag surface potential. {ital Ab} {ital initio} Hartree-Fock calculations of the molecular dipole moments successfully describe the surface potential changes. The chemically tailored electrodes were then incorporated in organic diode structures and changes in the metal/organic Schottky energy barriers were measured using an electroabsorption technique. These results demonstrate the use of self-assembled monolayers to control metal/organic interfacial electronic properties. They establish a ...

British Library Electronic Table of Contents (United Kingdom)

An extremely sensitive stripping voltammetric procedure for ultra-trace determination of iridium(III) is reported. The method is based on the interfacial accumulation of the iridium(III)-CTAB complex onto the glassy carbon electrode, followed by the catalytic reduction of the adsorbed complex in the presence of bromate. 0.3molL^-^1 acetate buffer pH 4.7+6.9x10^-^2molL^-^1 NaBrO3+2.7x10^-^5molL^-^1 cetyltrimethylammonium bromide (CTAB)+0.2molL^-^1 KCl was employed as the supporting electrolyte. The analytical procedure was verified by the analysis of the standard reference materials: Sea Water BCR-CRM 403 and Fresh Water NIST-SRM 1643d. The accuracy, expressed as relative error e%, was satisfactory, being lower than 6%, while precision as repeatability, expressed as relative standard deviat...

Energy Technology Data Exchange (ETDEWEB)

The research supported by this Department of Energy contract has primarily been devoted to the study of the electronic properties of surfaces with sub-micron size. In previous years, we have studied the photoexcitation of electrons from field emission tips by a focussed Argon-ion laser beam tuned to operate at specific photon energy. The photoexcited electrons escape into the vacuum by tunneling through a surface potential barrier which is distorted by the application of a strong electric field. The interest in these experiments lies in a better understanding of the photoexcitation process at low photon energies. The techniques that have been developed directly measure the excited state energy distribution of electrons emitted through the surface potential barrier. The basic information gained from this research is relevant to opto-electronic devices which rely on photoexcitation of electrons in the presence of strong interfacial electric fields for their ...

Energy Technology Data Exchange (ETDEWEB)

Lateral and vertical variabilities in the bulk and mechanical properties of silicic volcanic tuff at the potential nuclear waste repository site in Yucca Mountain, NV have been evaluated. Laboratory measurements have been performed on tuff specimens recovered from boreholes located to support the design of the Exploratory Studies Facility/North Ramp. The data include dry and saturated bulk densities, average grain density, porosity, compressional and shear wave velocities, elastic moduli, and compressional and tensional fracture strengths. Data from eight boreholes aligned in a northwest-southeast direction have been collected under the required quality assurance program. Three boreholes have penetrated the potential repository horizon. The information collected provides for an accurate appraisal of the variability of rock properties in the vicinity of the boreholes. As expected, there is substantial variability in the bulk and mechanical properties of the tuff ...

Energy Technology Data Exchange (ETDEWEB)

Turret moored Floating Production Storage and Offloading (FPSO) systems are considered suitable for a wide range of environmental conditions but experience of designing moorings for these units in harsh environments is limited. Furthermore, each floating production system has its own requirements as to the way the riser system is operated because of its dependence on both reservoir and site specific conditions. The current mooring codes do not have a consistent set of requirements; for example, the intact mooring system safety factors range from 1.5 to 2.3. Such vastly differing requirements result in wide variability in the intrinsic safety, reliability and cost. This paper describes a reliability analysis carried out for the first North Atlantic FPSO (Foinaven), to address the acceptance criteria for moorings by returning to the fundamentals. Although the analysis deals with FPSO`s, the approach is applicable to any catenary moored unit. One primary purpose of the mooring system is ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this report is to provide a brief overview and bibliography of those techniques that may have application for the evaluation of a site to determine if a high energy release event is nuclear in nature. This effort is motivated by recognition of the changing world political climate and the perception that low yield and non-proliferation issues will grow in importance as countries become increasingly involved as signators to treaties that are intended to limit the development and testing of nuclear weapons. Along with an increasing interest in such issues is the awareness of the need to implement improved capabilities for treaty monitoring programs that must deal with assessing suspicious occurrences of high energy release events. In preparing this report, it is recognized that monitoring can take two main forms. The first involves the resolution of unidentified events detected by seismic and satellite National Technical Means. Events of an indeterminate nature could occur ...

Energy Technology Data Exchange (ETDEWEB)

I present a promising route to harmonize distance measurements based on clump giants and RR Lyrae stars. This is achieved by comparing the brightness of these distance indicators in three environments: the solar neighborhood, Galactic bulge and Large Magellanic Cloud (LMC). As a result of harmonizing the distance scales in the solar neighborhood and Baade's Window, I derive the new absolute magnitude of RR Lyrae stars, M{sub v}(RR) at [Fe/H] = -1.6 (0.59 {+-} 0.05, 0.70 {+-} 0.05). Being somewhat brighter than the statistical parallax solution, but fainter than typical results of the main sequence fitting to Hipparcos data, these values of M{sub V}(RR) favor intermediate or old ages of globular clusters. Harmonizing the distance scales in the LMC and Baade's Window, I show that the most likely distance modulus to the LMC, {mu}{sub LMC} is in the range 18.24 - 18.44. The Hubble constant of about 70 km/s/Mpc reported by the HST Key Project is based on the assumption ...

Science.gov (United States)

This study is a contribution to the growing body of work on the influence of changes in the composition of an acrylic bone cement on various properties of the curing and cured material. The focus is on one commercially-available acrylic bone cement brand, Surgical Simplex P, and three variants of it and a series of properties, namely, setting time, maximum exotherm temperature, activation energy and frequency factor for the polymerization reaction, diffusion coefficient for the uptake of phosphate buffered saline, at 37 degrees C, ultimate compressive strength (UCS), plane-strain fracture toughness, fatigue life (under fully-reversed tension-compression stress), hardness (H) and elastic modulus (both determined using quasi-static nanoindentation), and the variation of the storage and loss moduli with frequency of the applied force in a dynamic nanoindentation test. It was found that (a) a 68% reduction in the volume of the activator, N,N dimethyl-4-toluidine, ...

Science.gov (United States)

The strength, stiffness, and range of single-stranded stainless steel (SS) and superelastic nickel-titanium (NiTi) archwires were compared with those of alternative leveling products, including nylon-coated and multistranded wires. Wire cross-sections were photographed after being potted in polymer, ground, and polished. Because the rectangular wires had rounded or beveled corners, gravimetric measurements and specific gravity calculations quantified the actual polygonal cross-sectional areas versus the ideal rectangular cross-sectional areas. Beveling reduced the cross-sectional areas by 7% to 8%; this decreased the wire stiffnesses by 15% to 19%. Using a testing machine, we measured the yield strengths, the elastic limits, and the ultimate tensile strengths in tension, and wire stiffnesses in 3-point bending. From cyclic loading tests, the elastic limits of the superelastic NiTi wires were approximately 90% and 45% of their ultimate tensile strengths for the ...

International Nuclear Information System (INIS)

The objective of this study is to evaluate the lifetime of Zr-2.5Nb pressure tube at Wolsung Unit-1. The testing materials (Effective full power year: 9.3 year, Accumulated nuetron fluence: 7.66#approx#8.91 x 1025 n/m"2) were sampled from M-11 tube at various position(inlet, middle and outlet). The cutting was carried out at hot cell to fabricate CT(Compact tension) specimen with 48 ppm hydrogen content. In the result of DHC test, irradiation-damaged specimen showed 4#approx#6 times faster DHC velocity(5.298E-0.8#approx#7.039E-8 m/s: 182 .deg. C) than non-irradiated specimen. These DHCV results also show slight faster than one of specimen from Pickering plant (average DHCV: 4.5E-8 m/s: 182 .Deg C). This faster DHCV can be explained with the fact that Wolsung Unit-1 have been operated in a severe conditions(higher cooling water temperature, high power and efficiency) than Pickering one. The striation spacing which was seen DHC fracture surface at irradiated specimen ...

International Nuclear Information System (INIS)

The collapse and fragmentation of initially prolate and oblate, magnetic molecular clouds is calculated in three dimensions with a gravitational, radiative hydrodynamics code. The code includes magnetic field effects in an approximate manner: magnetic pressure, tension, braking, and ambipolar diffusion are all modeled. The parameters varied for both the initially prolate and oblate clouds are the initial degree of central concentration of the radial density profile, the initial angular velocity, and the efficiency of magnetic braking (represented by a factor f _m_b = 10"-"4 or 10"-"3). The oblate cores all collapse to form rings that might be susceptible to fragmentation into multiple systems. The outcome of the collapse of the prolate cores depends strongly on the initial density profile. Prolate cores with central densities 20 times higher than their boundary densities collapse and fragment into binary or quadruple systems, whereas cores with central densities ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this work is to determine the ability of indigenous bacteria from a Venezuelan oil field to grow under reservoir conditions inside a porous media, and to produce metabolites capable of recovering residual crude oil. For this purpose, samples of formation waters from a central-eastern Venezuelan oil reservoir were enriched with different carbon sources and a mineral basal media. Formation water was used as a source of trace metals. The enrichments obtained were incubated at reservoir temperature (71{degrees}C), reservoir pressure (1,200 psi), and under anaerobic conditions for both outside and inside porous media (Berea core). Growth and metabolic activity was followed outside porous media by measuring absorbance at 660 nm, increases in pressure, and decreases in pH. Inside porous media bacterial activity was determined by visual examination of the produced waters (gas bubbles and bacterial cells). All the carbohydrates tested outside porous media showed good growth at ...

Science.gov (United States)

The purpose of this study was to evaluate the resin-dentin interfacial morphology and shear bond strength of several new and experimental dentin bonding systems classified as single-bottle/total etch, multi-step/total etch, and self-etching. Class 1 and 5 cavities were prepared from freshly extracted permanent molars and restored with composite resin. Each bonded sample was cross sectioned and one-half was completely demineralized and deproteinized, while the other half was polished along the cut surface to permit measurement of the thickness of resin-infiltrated dentin layer (RIDL) within intertubular dentin (iRIDL) and around the peritubular walls (pRIDL) of resin tags by SEM. Shear bond strength was measured for all the systems 2 minutes after photocuring. SEM showed iRIDL and resin tags of different morphology depending on material and dentin location. The iRIDL was thinner in superficial dentin and thicker in deep dentin. Peritubular RIDL (pRIDL) was thinner ...

Energy Technology Data Exchange (ETDEWEB)

Gas nitridation has shown excellent promise to form dense, electrically conductive and corrosion-resistant Cr-nitride surface layers on Ni-Cr base alloys for use as proton exchange membrane fuel cell (PEMFC) bipolar plates. Due to the high cost of nickel, Fe-base bipolar plate alloys are needed to meet the cost targets for many PEMFC applications. Unfortunately, nitridation of Fe-base stainless steel alloys typically leads to internal Cr-nitride precipitation rather than the desired protective surface nitride layer formation, due to the high permeability of nitrogen in these alloys. This paper reports the finding that it is possible to form a continuous, protective Cr-nitride (CrN and Cr{sub 2}N) surface layer through nitridation of Fe-base stainless steel alloys. The key to form a protective Cr-nitride surface layer was found to be the initial formation of oxide during nitridation, which prevented the internal nitridation typically observed for these alloys, and resulted in external ...

Energy Technology Data Exchange (ETDEWEB)

Significant ion irradiation during film growth is required for the formation of cubic boron nitride (cBN) films. Meanwhile, a huge level of intrinsic stress possibly induced by the ion bombardment has been frequently reported to result in cracking and/or lack of adhesion of deposited cBN films. The present work has been performed to investigate the interfacial and/or the buffer layer structures with better matching to the cBN film by relaxation of the film stress using ion-beam-assisted deposition (IBAD). Boron nitride films have been synthesized on Si(100) wafer and tungsten carbide (WC) substrates by depositing boron vapor under simultaneous bombardment with nitrogen ions and nitrogen-argon mixture ions in the energy range of 0.5-10 keV. Cubic BN films with enhanced tribological properties have been explored by inserting a BN layer with various B/N compositions as a controlled buffer at the interface. Significant relaxation of the film stress has been observed ...

Energy Technology Data Exchange (ETDEWEB)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr{sub 2}N, CrN, TiN, V{sub 2}N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited by the pre-oxidized/nitrided Fe-20Cr-4V, which exhibited {approx}5-20% better peak power output than untreated Fe-20Cr-4V, 2205, and 904L metal stampings. Durability ...

Energy Technology Data Exchange (ETDEWEB)

The overall goal of the proposed project is to explore the use of partitioning tracers to characterize dense nonaqueous phase liquids (DNAPLs) in aquifer systems. Bulk-phase partitioning tracers will be investigated to detect and determine DNAPL saturation, while interface partitioning tracers will be investigated to measure the area of the DNAPL-water interface. The specific objectives that will be addressed to accomplish this goal are: (1) Investigate the use of partitioning tracers to detect and determine both the saturation and interfacial area of DNAPLs in saturated porous media. (2) Investigate the effect of rate-limited mass transfer on the transport behavior of partitioning tracers. (3) Investigate the effect of porous-media heterogeneity on the transport behavior of partitioning tracers. (4) Develop and evaluate mathematical models capable of simulating the transport of partitioning tracers in complex systems. This proposal outlines an integrated approach ...

International Nuclear Information System (INIS)

As an unconventional surface alloying process, ion implantation has been utilized to improve the active-passive behavior and the pitting resistance of martensitic M50 engineering alloy. In a field simulation study, Cr-implantation only at 150 kev to a fluence of 2 x 10"1"7 ions/cm"2 prevented pitting. The best pitting resistance of the steel was obtained with multiple implantations of Cr and Mo. The intermixing effect of high fluence P-implantation into 304 stainless produced an amorphous surface alloy. The removal of the grain boundaries and the uniformity of the resulting structure had a great influence on corrosion properties. REED analysis indicated that the anodic passive films formed on P-implanted 304 stainless steel at 250 mV (SCE) in 0.5M H_2SO_4 was amorphous. Phosphorus and boron were implanted into 316 stainless steel to study the passivity of 316 stainless. Electrochemical experiments were carried out to evaluate the effects of phosphorus and boron on general and localized ...

Science.gov (United States)

Previous investigations have shown that both the early biological response and the mechanical properties of a porous hydroxyapatite bone graft substitute are highly sensitive to its pore structure. The objective of this study was to evaluate whether the pore structure continued to influence bone integration in the medium to long term. Two screened batches of porous hydroxyapatite (PHA) designated as batch A and batch B, with porosities of approximately 60 and 80%, respectively, were selected for this study and implanted for periods of 5, 13, and 26 weeks into the lower femur of New Zealand White rabbits. Histomorphometric analysis of the absolute volume of bone ingrowth within batch A and B implants from 5 to 26 weeks showed that the absolute volume of bone ingrowth was consistently lower in batch A (10-21%), compared to batch B implants (24-31%). However, when the volume of bone ingrowth was normalised for the available pore space, this difference was reduced (23-47% and 32-42% for ...

Energy Technology Data Exchange (ETDEWEB)

The compound semiconductor system InGaAsN exhibits many intriguing properties which are particularly useful for the development of innovative high efficiency thin film solar cells and long wavelength lasers. The bandgap in these semiconductors can be varied by controlling the content of N and In and the thin films can yet be lattice-matched to GaAs. In the present work, x-ray absorption fine structure (XAFS) and grazing incidence x-ray scattering (GIXS) techniques have been employed to probe the local environment surrounding both N and In atoms as well as the interface morphology of InGaAsN thin films epitaxially grown on GaAs. The soft x-ray XAFS results around nitrogen K-edge reveal that N is in the sp{sup 3} hybridized bonding configuration in InGaAsN and GaAsN, suggesting that N impurities most likely substitute for As sites in these two compounds. The results of In K-edge XAFS suggest a possible trend of a slightly larger coordination number of As nearest neighbors around In atoms ...

Science.gov (United States)

An x-ray diffraction approach has been developed for determination of the kinetics of growth of Pd/sub 2/Si layers. Epitaxial Pd/sub 2/Si films were grown on Si(111) substrates over a temperature range of 160-222/sup 0/C by a solid-state reaction between the substrates and the Pd overlayers. The parabolic rate equation was verified and rate constants showed Arrhenius behavior with an activation energy E/sub a/ = 1.06 eV and prefactor k/sub 0/ = 7 x 10/sup -4/ cm/sup 2//s. The low value of E/sub a/ suggests a short-circuit diffusion mechanism. It is reasonable to expect that impurities and microstructure may play important roles in the growth process. Impurity levels in the specimens were evaluated by analytic techniques suited to thin-film study: Rutherford backscattering spectrometry, secondary ion mass spectrometry, and Auger electron spectrometry. No impurities were present at concentrations approaching 1 at. %. Some O, C, and F were detected at the Pd/sub 2/Si/Si interfaces. The ...

Energy Technology Data Exchange (ETDEWEB)

The particle surface of Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} was modified by AlF{sub 3} as a new coating material to improve the electrochemical properties in the high cutoff voltage of 4.5 V. The AlF{sub 3}-coated Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} showed no difference in the bulk structure compared with the pristine one and the uniform AlF{sub 3} coating layers whose thickness is of about 10 nm covered Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} particles, as confirmed by a transmission electron microscopy. The AlF{sub 3} coating on Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} particles improved the overall electrochemical properties such as the cyclability, rate capability and thermal stability compared with those of the pristine Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2}. Such enhancements were attributed to the presence of the stable AlF{sub 3} layer which acts as the interfacial stabilizer on the surface of Li[Ni{sub 1/3}Co{sub ...

Energy Technology Data Exchange (ETDEWEB)

The paper describes a lithium battery researched on under the Moonlight Project which is a long life secondary battery with high energy density and high power density. Using as a base a Li4SiO4 system which exhibits stable and high Li[sup +] conductivity as solid electrolyte material, partial Si[sup 4+] is replaced with divalent ions such as B[sup 3+] and Al[sup 3+] or divalent ions such as Ni[sup 2+] and Co[sup 2+], by which Li[sup +] for electric charge compensation can be increased and conductivity is enhanced. As to a LiTi2P3O12 system, Ti[sup 4+] is replaced with Sc[sup 3+] and Y[sup 3+]. In both systems, by replaCing Si[sup 4+] or Ti[sup 4+] with trivalent metal ions and increasing mobile Li[sup +], those with ion conductivity exceeding that at 300[degree]C, 10[sup -3]Scm[sup -1], can be developed. TiS2 and NiPS3 are prepared as cathode material and miniature cells are trially fabricated. Various polarization phenomena are observed and a lot of improvements are needed, but for ...

International Nuclear Information System (INIS)

Ultra low loading noble metal (0.04-0.12 mg_P_t/cm"2) based electrodes were obtained by direct metallization of non-catalyzed gas diffusion layers via dual ion beam assisted deposition (IBAD) method. Fuel cell performance results reported earlier indicate significant improvements in terms of mass specific power density of 0.297 g_P_t/kW with 250 A thick IBAD deposit (0.04 mg_P_t/cm"2 for a total MEA loading of 0.08 mg_P_t/cm"2) at 0.65 V in contrast to the state of the art power density of 1.18 g_P_t/kW using 1 mg_P_t_(_M_E_A_)/cm"2 at 0.65 V. In this article we report the peroxide radical initiated attack of the membrane electrode assembly utilizing IBAD electrodes in comparison to commercially available E-TEK (now BASF Fuel Cell GmbH) electrodes and find the pathway of membrane degradation as well. A novel segmented fuel cell is used for this purpose to relate membrane degradation to peroxide generation at the electrode/electrolyte interface by means of systematic pre and post ...

Energy Technology Data Exchange (ETDEWEB)

Film boiling is the mode if boiling during which the hot surface is separated from the vaporizing liquid by a nearly continuous film vapor. Film boiling is usually considered a very undesirable boiling regime since it is a relatively quiet and inefficient mode of heat transfer, particularly as compared to nucleate boiling. It is customary to analyze the two-phase flow regime of laminar flow film boiling by assuming the two-phase flow regime of laminar flow film boiling by assuming an idealized vapor film flow characterized by a smooth liquid-vapor interface. However, during stable flow film boiling, the wavy nature of the liquid-vapor interface and its role in local heat and mass transport have been largely ignored. The vapor interface is rarely stationary. Interfacial waves may substantially augment the heat transfer rates throughout the layer. The present analysis treats stagnation point flow film boiling on a sphere immersed in a subcooled liquid. The effect of ...

Energy Technology Data Exchange (ETDEWEB)

Chromium nitride/Cr coating has been deposited on surface of 316L stainless steel to improve conductivity and corrosion resistance by physical vapor deposition (PVD) technology. Electrochemical behaviors of the chromium nitride/Cr coated 316L stainless steel are investigated in 0.05 M H{sub 2}SO{sub 4}+2 ppm F{sup -} simulating proton exchange membrane fuel cell (PEMFC) environments, and interfacial contact resistance (ICR) are measured before and after potentiostatic polarization at anodic and cathodic operation potentials for PEMFC. The chromium nitride/Cr coated 316L stainless steel exhibits improved corrosion resistance and better stability of passive film either in the simulated anodic or cathodic environment. In comparison to 316L stainless steel with air-formed oxide film, the ICR between the chromium nitride/Cr coated 316L stainless steel and carbon paper is about 30 m{omega} cm{sup 2} that is about one-third of bare 316L stainless steel at the compaction ...

Energy Technology Data Exchange (ETDEWEB)

Several steam generator tube rupture accidents have occurred at plants in the past. In this paper the Computational Multi-Fluid Dynamics (CMFD) investigation of the horizontal steam generator thermal-hydraulics during the tube rupture accident is performed. A guillotine of a steam generator U-tube is assumed with choked flow from the primary to the secondary side of the steam generator. We have computed water and steam velocity fields, steam volume fraction distribution on the steam generator secondary (shell) side, as well as the swell level increase. The simulation results are a support to the safety analyses of the steam generator tube rupture accident. Numerical simulation is performed with the multidimensional multi-fluid modelling approach. The two-phase flow around steam generator tubes in the bundle is modelled by the porous media approach. Interfacial mass, momentum and energy transfer are modelled with the closure laws. The governing equations are solved ...

Energy Technology Data Exchange (ETDEWEB)

The National Institute of Materials Science (NIMS) has utilized the in-house alloy design program to develop a 5{sup th} generation Ni-base single crystal superalloy, TMS-196 with superior high temperature creep, thermo mechanical fatigue (TMF) and oxidation resistance by incorporating further ruthenium (Ru) and chromium (Cr) content over the compositions of 4{sup th} generation superalloys. With Ru additions in advanced superalloys to enhance phase stability, higher content of refractory elements can be accommodated to provide further strengthening; the associated oxidation resistance can be improved by the increase in Cr additions. In present article, TMS-196 has been subjected to cyclic/isothermal oxidation tests at 1100 C and 900 C, creep at conditions between 800 C{proportional_to}1100 C/137MPa{proportional_to}735MPa and TMF cycles. Preliminary studies indicate that the surface of oxidized TMS-196 can exhibit continuous alumina layer attributing good oxidation resistance similar ...

International Nuclear Information System (INIS)

Full text: Chemical-technology approaches allowing to intensification the prevention processes of gas hydrates formation at motion of gas-liquid stream of natural gas in system natural gas well - gas wire have been worked up. Technological regimes of treatment of gas stream have been determined. Linear correlation dependences inhibitor electrolytes contained hydrated ions with different ion radii and charges of subgroups of alkali elements with one - type electron configuration were obtained. Important physico-chemical parameters of electrolytes have been determined: activity; coefficients of activity, viscosity, diffusion; density; heat capacity; heat conductivity; surface tension and freezing-point. The features of continuous influence of inhibitory factors on process of gas flow at low temperatures and relatively high pressure differences ?P have been studied by using of technological installation modulating the system natural gas well - gas wire. The ...

International Nuclear Information System (INIS)

AIM: To assess the impact of the introduction of a computed tomography (CT) imaging protocol for multi-trauma patients on the workload, overall diagnostic yield, and effect on detection of cervical spine injury and pneumothorax. METHOD: Between February 1997 and April 2004, all patients presenting acutely to the Emergency Department (ED) with haemodynamically stable trauma (Abbreviated Injury Scale 3 or more) involving more than two body systems were imaged with a comprehensive pre-set helical CT protocol (including non-contrast head, cervical spine: cranio-cervical and cervico-thoracic junctions; and oral and intravenous contrast-enhanced thoracic, abdomen and pelvis) after initial triage and a standard trauma series of radiographs (chest, lateral C-spine and pelvis). Diagnosis of cervical spine fracture and pneumothorax was noted before and after the CT protocol was carried out and findings from all studies were recorded prospectively. RESULTS: Over the 7-year period 296 multi-trauma ...

Energy Technology Data Exchange (ETDEWEB)

An historic Strontianite-type specimen from Strontian, Scotland, UK, was characterized to broaden our knowledge on luminescence properties of common carbonates. These fibrous aggregates are Strontianite (Sr{sub x}Ca{sub 1-x}CO{sub 3}) with circa 6% of CaO, interfacial water, hydrosilicate anions and substitutional divalent cations, e.g., Ca{sup 2+}, Mn{sup 2+}, Fe{sup 2+} in structural Sr{sup 2+} positions. The specimen was analyzed by X-ray Fluorescence Spectrometry (XRF), Environmental Scanning Electron Microscopy coupled with an Energy Dispersive X-ray Spectroscopy (ESEM-EDS) probe, Spatially-resolved Cathodoluminescence under the Scanning Electron Microscope (SEM-CL), Differential-Thermal Analyses (DTA), Thermogravimetry (TG), Thermoluminescence (TL), Radioluminescence (RL) and High Resolution Spectra Thermoluminescence (3DTL), to gain an overview of the spectral emissions, the defect linkages were modified by heating from room temperature (RT) up to 500 deg. ...

Science.gov (United States)

In order to understand not only the mechanisms of earthquakes, but also the origin of diverse behavior of faults and plate boundaries, one must integrate (1) field studies on faults to understand deep intrafault processes, (2) laboratory work to reproduce those processes and determine mechanical and transport properties of fault zones, (3) theoretical and numerical studies analyzing fault motion, including earthquake generation processes, based on the constitutive properties determined by laboratory studies, and (4) seismological and geodetic studies revealing dynamic fault motion during earthquakes and diverse aseismic fault behavior. Ideally, such integrated studies should be carried out for a selected fault that produced an earthquake with good seismic/geodetic records so the prediction from (1) to (3) can be fully tested with (4), rather than selecting favorite data in the literature. Present session is organized to promote such integrated fault and earthquake studies. This ...

Energy Technology Data Exchange (ETDEWEB)

Historically the organizational models have followed an evolution that has underlined a parallel trend to the complexity of the market, introducing as different mechanisms of coordination. Up to yesterday the winning model it was that hierarchical that however it is not certainly immune from limits. Beginning from eight hundred and especially in the nine hundred experts of organization have studied an alternative or supplementary model to that hierarchical: the bureaucratic model. This last entrusts the organization of the firm to the norms and the procedures considering them like the best integrating mechanism of development of the organizations. Today it is not made that to speak of the model to net, but it would be a serious error if this had to a substitutive model thought of the precedents, that can work then without hierarchy and without alone procedures entirely thanks to the use of Internet. In the present job are individualized new models of management of the private firms and ...