Energy Technology Data Exchange (ETDEWEB)

The product of several advanced physical coal cleaning processes is a dry, ultrafine coal (DUC), in the order of 10 microns mean mass diameter. To utilize this fuel commercially, cost-effective, environmentally safe systems must be provided for the storage, transport, and handling of this finely divided form of fuel. The objective of the project described herein is the development of total logistics systems for DUC, including experimental verification of key features. The systems to be developed will provide for safe, economic, and environmentally protective storage and delivery of DUC for residential, commercial, and industrial uses. 20 figs.

International Nuclear Information System (INIS)

Evaporation of "9"9"mTc-pertechnetate at about 2500"0C on a carbon surface generates an ultrafine aerosol of labelled carbon clusters. Its particle size of about 2-5 nm enables the aerosol to behave similarly to a gas regarding the ability of penetration. After inhalation, the radioactive particles adhere to the walls of the respiratory bronchioli and alveoli. The high concentration of the radioactivity in the argon carrier gas makes it possible to record a scintigram after a single deep breath. We studied four healthy volunteers and 79 patients including 34 with a tentative diagnosis of pulmonary embolism, 20 with bronchus carcinoma, and 15 with various other lung diseases. Ten of these patients were infants, the youngest being nine months old. All patients also had a perfusion scintigraphy. (orig.).

Science.gov (United States)

During 1978 the Engineering Board of SRC granted Specially Promoted Program status to the Coal Technology program. This recognized that coal would increase in importance as the cost of liquid and gaseous hydrocarbons rises with the decreasing availability of petroleum related sources. It was, therefore, considered necessary to anticipate and improve, through SRC supported research, the technologies required to win, transport, convert to liquid and gaseous fuels and utilize coal and coal based substances. In view of the interest in the program, and also in the hope of reaching a still wider audience the reports of the two meetings have been combined in this single booklet. The reports indicate specific problems of importance in coal winning and coal conversion but, naturally, do not cover all of the program priorities.

Wastenet

...Synthesis of low-temperature, fast, single-firing body for porcelain stoneware tiles with coal gangue Synthesis of low-temperature, fast, single-firing body for porcelain stoneware ... tiles with coal gangue Synthesis of low-temperature, fast, single-firing body for porcelain stoneware tiles with coal gangue Wei et al.,... Article Synthesis of low-temperature, fast, single-firing body for porcelain stoneware tiles with coal gangue Qiangwei Wei1, Wenyuan Gao1*, and Xinguo ...According to phase diagram theory, a low-temperature, fast, single-firing body mix for porcelain stoneware tiles was designed in the quaternary system CaO-MgO-Al2O3-SiO2, using ...

Science.gov (United States)

Not Available

Science.gov (United States)

Alternative sources of fuel, especially for transport, continue to be of interest, as the availability of petroleum is likely to decline in the foreseeable future. Coal is a perfect alternative since it is abundant and can readily be refined to products similar to petroleum fuels. This work details the continuing research program undertaken by the European Commission, bringing together results of studies by international experts in the field. The editors have synthesized vast amounts of recent literature to produce a state-of-the-art review covering synthetic processes, single and two-stage hydrogenation processes, processing of coal with heavy oil and catalysis.

Energy Technology Data Exchange (ETDEWEB)

Single-particle combustion of coal char is analyzed using a generalized shrinking core model. Finite volume method, which was earlier employed by the authors in solving moving boundary problems involving fluid-solid noncatalytic reactions in general, is used to solve fully transient mass and energy equations. The model takes into account convection and diffusion inside the particle as well as in the boundary layer. The computed results are compared with the experimental data of the authors for combustion of coal char in a fluidized bed combustor. The effects of parameters such as bulk temperature and initial particle radius on the combustion dynamics are examined. The phenomena of ignition and extinction are also investigated. Finally, the importance of Stefan flow, originating due to nonequimolar counterdiffusion, on combustion of coal char is analyzed.

Energy Technology Data Exchange (ETDEWEB)

The lignite used for Phase I of the project was a Texas lignite from the Martin Lake mine obtained from the stockpile for the Martin Lake Power Plant of the Texas Utilities Generating Company. The power requirements for the fluid-energy mill were determined from the measured steam (or air) temperatures, pressures and pressure drops and the lignite flow rate. The instrument locations for the tests are shown on Figure 1. All of the instruments were connected to a microcomputer via an analog input interface board. Data were recorded on disks periodically throughout the tests. Appropriate calibration procedures were followed to assure that reliable data were being obtained. The combined grinding/drying tests were conducted in Vicksbuth, MS at Ergon, Inc.'s fluid-energy-mill facility. both steam and air were used as grinding fluids. With steam, tests were used as grinding fluids. With steam, tests were run with the following temperatures maintained inside the pulverizer: 310/sup ...

Science.gov (United States)

Because hydrogenation of coal to liquid products (oils) is accompanied by distributions of complex by-product mixtures (IOM, preasphaltenes, asphaltenes and gases) which change as a function of reaction variables (time, temperature and pressure) and reactor configuration, the determination of selectivity relationships for coal liquefaction catalysts has been a difficult and time-consuming task involving numerous experiments to adequately describe catalyst performance over a range of conditions. This paper describes a method for analyzing the experimental results of coal liquefaction reactions which may be applied to a number of aspects of coal liquefaction research and process control, including: rapid selectivity and performance screening for catalysts; correlation of laboratory results with process parameters; and optimization of product yield for plant process conditions. Catalyst selectivity and ...

Energy Technology Data Exchange (ETDEWEB)

In the GE 7FDL single cylinder research diesel engine, in-cylinder high-speed photographic studies were conducted on coal-water slurry (CWS) fuel combustion. Distinct flames of pilot and CWS combustion were noticed. It was proven that the coal fuel burns after piston impingement and secondary atomization. Agglomerated particles will develop when combustion conditions are not favorable. Cylinder pressure data were simultaneously recorded for each film frame. Heat release data can thus be produced for each photo study. Most of the findings of earlier combustion studies on engine performance were confirmed.

British Library Electronic Table of Contents (United Kingdom)

Vanadium carbide is the most effective grain growth inhibitor for ultrafine WC-Co composites due to its high solubility and mobility in the cobalt phase at relatively low temperatures; however, there are still some debates over the best way to introduce it into the WC-Co formulation. In this paper, the differences between admixed and chemically doped grain growth inhibitors on the microstructural development and properties of an ultrafine WC-10Co composite are discussed. The densification rate of chemically doped samples is slower in the early stage of sintering and the WC grain sizes of the sintered alloys are finer than those of admixed samples, leading to the increase of hardness and transverse rupture strength of the sintered alloys. The effectiveness of the chemically doped inhibitor ...

British Library Electronic Table of Contents (United Kingdom)

In this paper we present the results of time series analysis for a coal mining region based on partial unmixing. We test the method also known as mixture tuned matched filtering on an eight image Landsat 5 TM and Landsat 7 ETM+ time series covering the period from 1987 to 2003. Common change detection methods often include the comparison of two interactively generated classification results, such as derived from Maximum Likelihood classification. These approaches often yield highly accurate results. However, disadvantages include a strong analyst bias and hardly repeatable results. For a quantitative monitoring of a single surface class' development over time they are often not recommendable. Our goal was to test an unbiased quantitative way to assess the development of coal surfaces, such...

British Library Electronic Table of Contents (United Kingdom)

The nanocomposite WC-Co powders were prepared through planetary ball milling method. Effects of grain growth inhibitor addition and the vacuum sintering parameters on the microstructure and properties of ultrafine WC-10Co cemented carbides were investigated using X-ray diffractometer, scanning electron microscope and mechanical property tester. The results show that VC and NbC additions can refine the WC grains, decrease the volume fraction of Co3W3C phase in ultrafine WC-10Co cemented carbides, and increase the hardness and fracture toughness of the base alloys. After sintering for 60 min at 1400 degreeC, the average grain size and hardness of ultrafine-grained WC-10Co-1VC cemented carbide are 470 nm and HRA 91.5, respectively. The fracture toughness of cemented carbide WC-10Co-1NbC alloy...

Energy Technology Data Exchange (ETDEWEB)

A discussion is presented of the chemistry and technology of coal liquefaction and the physics and technology of coal desulfurization. 31 refs.

Energy Technology Data Exchange (ETDEWEB)

Coal solids (SRC) and distillate oils are combined to afford single-phase blends of residual oils which have utility as fuel oils substitutes. The components are combined on the basis of their respective polarities, that is, on the basis of their heteroatom content, to assure complete solubilization of SRC. The resulting composition is a fuel oil blend which retains its stability and homogeneity over the long term.

Energy Technology Data Exchange (ETDEWEB)

The cost of liquid fuels from coal is a complex function of many factors, such as capital investment, cost of coal and labor cost. Furthermore, the cost will depend on geographical position, the size of the operation and the efficiency of the process. There is no single answer and case studies will have to be made to establish economics at different locations. In the following, the 1980 order-of-magnitude investment costs and operating costs for a coal liquefaction plant are estimated. For a Sasol II type of plant with the product output indicated earlier, the total capital cost is estimated at $4 billion in 1980 dollars. Capital cost accounts for approximately 50%, utilities and materials for 30%, and labor for 20% of the total cost. Given the market value of by-product ethylene ($175/t), tar products ($300/t), chemicals ($300/t), ammonia ($200/t) and sulfur ($25/t), the credit for by-products is $146 ...

Energy Technology Data Exchange (ETDEWEB)

A combination of erosion and corrosion at the Victoria Junction coal preparation plant in Sydney, Nova Scotia was causing serious problems. Schedule 80 mild steel pipes were starting to fail as well as some quarter-inch steel plates in the lauders and chutes. Some corrosion tests were carried out and the high chloride level in the process water was felt to be the single most important contribution to the corrosion problem. Cast basalt was selected as a solution to the pipe wear problem. Three different types of abrasion/corrosion-resistant tiling - basalt tiles, kalceram tiles and ceramic tiles were well suited to the chloride conditions at this plant.

Science.gov (United States)

The first quarter 1982 report summarizes the operating and test data obtained at the six ton per day Advanced Coal Liquefaction Research and Development Facility in Wilsonville, Alabama. The Wilsonville R and D Facility was in operation 52% of the period with scheduled shutdowns accounting for 33% of the downtime. Illinois 6 coal from the Burning Star No. 2 mine was processed during Run 236. The three process units of the Wilsonville facility were operated in a non-integrated mode to evaluate process parameters and to test equipment and operating modifications. Data were obtained in the following areas: In the SRC Unit: operation at low severity reaction conditions for single stage liquefaction with a high LSRC recycle rate using Illinois 6 coal; process solvent activity control; and preliminary feeding tests with hydrotreated SRC as a replacement for LSRC in the process solvent. In the CSD Unit: ...

Energy Technology Data Exchange (ETDEWEB)

Two computational problems were worked on for this study. The first chapter examines the option of coal combustion using oxygen feed with carbon dioxide recycle to control the adiabatic flame temperature. Computer simulations using an existing state-of-the-art 3-dimensional computer code for turbulent reacting flows with reacting particles were employed to study the effects of increased carbon dioxide mole fraction on the char burnout, radiant heat transfer, metal partitioning, and NOx formation. The second chapter compares assumptions for the CO/CO{sub 2} ratio at the surface of mineral inclusions made in previous studies to predictions obtained from a pseudo-steady state kinetic model (SKIPPY) for a single porous particle. The detailed kinetic simulations from SKIPPY for varying particle sizes and bulk gas compositions were used to develop algebraic expressions for the CO/CO{sub 2} ratio that can be incorporated into metal vaporization ...

Energy Technology Data Exchange (ETDEWEB)

The global production of steel is predicted to increase rapidly to meet future demands. In order to conserve the natural resources, certain measures must be taken. These include perfecting the recycling of steel, improving the performance to extend the life of the material, and reduce the need for massive production of steel by increasing the strength of the material. This paper presented a design concept for ultrafine complex microstructure steel. The National Research Institute for Metals in Japan has worked on a project which investigated 800 MPa ferrite steel for welded structures with a chemical composition similar to 400 MPa-class plain carbon steel. The doubled strength was attributed to grain refinement. Novel welding techniques were also used for joining the ultrafine microstructure. In this study, low carbon Si-Mn ferrite-pearlite steels were subjected to a thermo-mechanical treatment to produce a microstructure of 1 micron order ...

Energy Technology Data Exchange (ETDEWEB)

The As Pontes coal-fired power plant in northwest Spain is the largest single emitter of sulphur dioxide in the 'old' EU15. The plant is also among the largest emitters of nitrogen oxides and carbon dioxide in the region, according to the EPER (European Pollutant Emission Register). But Spain has also several other large emitters of air pollutants. The Andorra which is located in the province of Teruel is one of them. The Andorra power plant emitted 209,148 tones of SO{sub 2} in 2002 which makes it the second largest single emitter of SO{sub 2} in the EU15. It also emitts large quantities of NOx. Also in the northwest of Spain, the Composilla and La Robla power plants are the SO{sub 2} and NOx emitters.

Energy Technology Data Exchange (ETDEWEB)

A total of nine papers were presented at the course with the following titles: peat accumulation and coal basins; coal composition; coal quality; sedimentary environments of coal; generation, storage and migration of natural gas in coal bed reservoirs; geophysical log interpretation; the Ardley coal zone of central Alberta; stratigraphy and sedimentary environment of the Coalspur Formation; and the coal-bearing Luscar Group of western Alberta. All of these papers have been abstracted separately.

British Library Electronic Table of Contents (United Kingdom)

For an ultrafine grain ferrite/cementite (UGF/C) steel, the Charpy impact energy was measured at temperatures from 373K to 4.2K, and tensile tests were carried out at temperatures between 323K and 77K. For the steel with annealed microstructure, the ductile-to-brittle transition appearance temperature (DBTT) was lower than the Charpy transition temperature (CTT). With increasing annealing time at 873K, the DBTT and the CTT increased, and the DBTT approached the CTT. The DBTT decreased with decreasing effective grain size. The effective grain size correlated to the grain size of the larger grain size peak in the distribution of grains with {100} planes. The annealed microstructures had higher yield strength for equivalent toughness (including upper shelf energy, DBTT and CTT) compared to th...

British Library Electronic Table of Contents (United Kingdom)

Magnetic pulse welding is a solid state impact welding process, similar to explosive welding, which produces metallurgical bond by oblique high-speed impact between two metal bodies. This violent impact removes the metal surface oxide layers and then joins the two atomic level clean metal surfaces together by the incidental compression pressure. The impact velocity is at 200?400?m/s and the being welded metal surface undergoes severe plastic deformation with strain rate in the order of 106?107?s?1. The ultrafine-grained structure was observed on the welded interface. This article studied two types of similar material lap joint interfaces and the base metals were aluminum alloy 6061 and copper alloy 110. Nano-indentation testing shows that the welded interfaces have significantly greater ha...

Energy Technology Data Exchange (ETDEWEB)

Ultrafine particles of Co-P were synthesized by direct ball milling of Co and P powders and also investigated as a reversible hydrogen storage electrode material. The electrochemical results demonstrated that the reversible charge-discharge capacity of the Co-P electrode can reach more than 300mAh/g. In addition, the cycling ability and high rate capability of the Co-P electrode are excellent with only 5% capacity decay after 100 cycles at a high rate of 300mA/g. The temperature-programmed desorption measurements (TPD) of the Co-P electrode revealed that the charge and discharge reactions of the Co-P electrode proceeds predominantly through electrochemical hydrogen storage mechanism and the electrooxidation of cobalt contributes only a negligible part to the reversible electrochemical capacity. (author)

Energy Technology Data Exchange (ETDEWEB)

As oil supplies diminish, Britain will have to rely more and more on coal as one of the energy alternatives. To burn coal cleanly and efficiently coal will have to be converted into gas and liquid fuels to replace natural gas and oil. The research and development programme of the National Coal Board is directed towards meeting these new challenges. This paper outlines some of the Coal Board's current projects in the fields of industrial combustion, power generation, domestic combustion, coal gasification and coal liquefaction. 10 figs.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Devolatilization, char combustion and emission characteristics of different single fuel particles were studied under various fluidized bed combustor conditions, in order to develop a classification system which enables prediction of the behaviour of different fuels ranging from fixed carbon rich coals to volatile rich woods and plastics. To investigate formation reaction, the concentration of CO, CO{sub 2}, total hydrocarbons, O{sub 2}, NO and N{sub 2}O were measured continuously. Additionally, temperature histories of the particles were recorded by implanting thermocouples. Devolatilization and char combustion were analysed by an integral and differential method. The integral analysis uses global rates which were compared with the ultimate and proximate analyses and used to classify the fuels. In the differential analysis the single physical and chemical steps viz mass transfer from the bulk gas to the particle surface, ...

Energy Technology Data Exchange (ETDEWEB)

An investigation of the effect of blending of two different coals in various ratios on the hydrogenation reaction was carried out using a red mud-sulphur catalyst. Three Japanese coals and an Australian brown coal were used in the study. The conversion of the blended coals was compared with that obtained with each of the coals alone. A blend of the Yallourn brown coal and Shin-Yubari coal showed a synergism: it is considered that hydroaromatics from the Japanese coal promote the hydrogenation of the Yallourn coal. (The tables and captions in this paper are in English).

International Nuclear Information System (INIS)

A simple and rapid laser fluorometric determination of trace and ultra trace level of uranium in a wide variety of low uranium content materials like soil, basic and ultra basic rocks, plant ash, coal fly ash and red mud samples is described. Interference studies of some common major, minor and trace elements likely to be present in different geological materials on uranium fluorescence are studied using different fluorescence enhancing reagents like sodium pyrophosphate, orthophosphoric acid, penta sodium tri-polyphosphate and sodium hexametaphosphate. The accurate determination of very low uranium content samples which are rich in iron, manganese and calcium, is possible only after the selective separation of uranium. Conditions suitable for the quantitative single step extraction of 25 ng to 20 #mu#g uranium with tri-n-octylphosphine oxide and single step quantitative stripping with dilute neutral sodium pyrophosphate, ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to evaluate the potential benefits of applying multiseam [well] completion (MSC) technology to the massive stack of low-rank coals in the Powder River Basin. As part of this, the study objectives are: Estimate how much additional CBM resource would become accessible and technically recoverable--compared to the current practice of drilling one well to drain a single coal seam; Determine whether there are economic benefits associated with MSC technology utilization (assuming its widespread, successful application) and if so, quantify the gains; Briefly examine why past attempts by Powder River Basin CBM operators to use MSC technology have been relatively unsuccessful; Provide the underpinnings to a decision whether a MSC technology development and/or demonstration effort is warranted by DOE. To a great extent, this assessment builds on the previously published study (DOE, 2002), which contains ...

Energy Technology Data Exchange (ETDEWEB)

The paper discusses the status of coal as a raw material and energy source. After referring to coal preparation and the costs it involves the author deals with coal/liquid suspensions and their fueling uses. Access is given to different aspects concerning the use of coal for electric power and heat generation. They include pollution abatement measures, economic analyses and fuel engineering in the case of coal. Further sections are dedicated to upgrading procedures such as the gasification, liquefaction and coking of coal. A bibliography informs the reader about further publications available on the subject. (HAG).

Science.gov (United States)

A process is described for maintaining the proportions of each coal in a coal blend at a desired level. The process involves (1) making a spectral analysis, preferably by infrared spectrometry, of at least one sample of the coal blend, the sample having known desired proportions of each coal, (2) making a spectral analysis of the coal blend sample of unknown proportions of each coal, (3) comparing the spectral analyses of steps (1) and (2), and (4) upon noting a significant difference between the spectral analyses of steps (1) and (2), making adjustments to achieve a final coal blend having proportions of each coal closer to those of the blend of known desired proportions of each coal. The relationship of the aromatic to aliphatic groupings is preferably determined by spectral analysis of each ...

Science.gov (United States)

The AFGD process as demonstrated by Pure Air at the Bailly Station offers a reliable and cost-effective means of achieving a high degree of SO{sub 2} emissions reduction when burning high-sulfur coals. Many innovative features have been successfully incorporated in this process, and it is ready for widespread commercial use. The system uses a single-loop cocurrent scrubbing process with in-situ oxidation to produce wallboard-grade gypsum instead of wet sludge. A novel wastewater evaporation system minimizes effluents. The advanced scrubbing process uses a common absorber to serve multiple boilers, thereby saving on capital through economies of scale. Major results of the project are: (1) SO{sub 2} removal of over 94 percent was achieved over the three-year demonstration period, with a system availability exceeding 99.5 percent; (2) a large, single absorber handled the combined flue gas of boilers generating 528 MWe of ...

Energy Technology Data Exchange (ETDEWEB)

This article puts the case for coal fired combined cycle gas turbine (CCGT) power plants. The need to gasify the coal for the CCGT, use of fluidised bed combustors or gasification systems, the difference in prices of coal and natural gas, and coal and natural gas reserves are discussed. (UK)

Energy Technology Data Exchange (ETDEWEB)

The dispersion mechanism of highly loaded coal-water mixture (CWM) in the presence of a polyelectrolyte additive was investigated. Two important factors have been found: the ability of the additive to apply a sufficient electric repulsive force to the coal particles, and an appropriate affinity of the additive to the coal surface.

Energy Technology Data Exchange (ETDEWEB)

Samples of pure Cu, bronze (Cu-10 wt.% Zn) and brass (Cu-30 wt.% Zn) with stacking fault energies (SFE) of 78, 35, and 14 mJ/m{sup 2}, respectively, were processed by high-pressure torsion (HPT) and by a combination of HPT followed by cold-rolling (CR). X-ray diffraction measurements indicate that a decrease in SFE leads both to a decrease in crystallite size and to increases in microstrain, dislocation and twin densities for the HPT and HPT + CR processed ultrafine-grained (UFG) samples. Compared with processing by HPT, subsequent processing by CR refines the crystallite size of all samples, increases the twin densities of UFG bronze and brass, and increases the dislocation density in UFG bronze. It also decreases the dislocation density in UFG brass and leads to an unchanged dislocation density in UFG copper. The results suggest there may be an optimum stacking fault energy for dislocation accumulation in UFG Cu-Zn alloys and this has important implications in ...

Energy Technology Data Exchange (ETDEWEB)

Combustion performance trials were conducted on a commercial sample of Coal Valley coal from the Coalspur coalfield in the foothills region of Alberta. The project included an analytical investigation of the coal and coal ash properties as well as combustion studies in the CCRL pilot-scale, pulverized coal-fired boiler, under conditions representative of those in large steam boilers. This report gives the objectives of the project, the analyses of the coals, and describes the facilities and operational procedures. An evaluation of the experimental results and the conclusions are presented.

Science.gov (United States)

... ENERGY CONSERVATION, ENERGY CONSUMPTION, ELECTRIC POWER DISTRIBUTION, FOSSIL FUELS, COAL, BRAYTON CYCLE. ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes a research and development project to quantify the effects of cleaning the coal feed on the yield patterns and processing rates for the Liquid Solvent Extraction (LSE) direct coal liquefaction process and to obtain information on the effect of the co-refining of coal-derived and petroleum distillates to premium transport fuels. 6 refs., 25 figs., 40 tabs.

Science.gov (United States)

In addition to an executive summary and glossary, the following sections are included: Clean Boiler Fuel Demonstration Plant; Development of Coal Feeders for Coal Gasification Operations; Development of a Continuous Dry Coal Screw Feeder; Coal Feeder Development Program; Engineering and Technical Support; Technical Assistance Services; and Conceptual Design for an Advanced Coal Liquefaction Commercial Plant. (EJH)

Energy Technology Data Exchange (ETDEWEB)

The studied coal bearing series has a parallel origin. The following facial complexes are isolated in its composition: lakes free of vegetation without coal interlayers; overgrown lakes of their margins which are poor in coals; swampy lakes, whose peat beds formed coal layers of shallow or moderate depth; channel sediments without coal layers and swamps from between channel spaces which created thick coal strata of high quality for which, however, a strong changeability in thickness is intrinsic. The coal strata are normally split towards the central parts of the lake basins and river channels. The coal presence of the suite is reduced along the section which is associated with the replacement of the lake swamp conditions of sedimentation by lake river conditions. A paleotectonic analysis established that the ...

Energy Technology Data Exchange (ETDEWEB)

The objectives of the Upgraded Coal Interest Group (UCIG) are as follows: Review and update the status of various coal upgrading technologies and developments and critically assess the results. Perform engineering screening analyses on various coal upgrading approaches. Perform commercialization analyses that will promote the availability and use of upgraded coal products by quantifying the benefits of using them. Identify market opportunities for introduction of upgraded coals. Perform critical analyses on a variety of coals and technologies in areas important to users but not readily available. Perform critical experiments which will show the differences between technologies.

Energy Technology Data Exchange (ETDEWEB)

Discusses Czechoslovak regulations for determining moisture content in brown coal. Standard formulae for determining total moisture content and residual water content are described. Factors that influence accuracy in determining moisture content under laboratory conditions are analyzed: brown coal type, season of the year, air humidity, method and duration of coal sample drying, number of coal samples simultaneously dried in 1 dryer, ash content of coal. On the basis of analysis recommendations for a modified method of determining moisture content in brown coal are made. 5 refs.

Energy Technology Data Exchange (ETDEWEB)

The overall goal of the Coal Liquefaction Program of the Office of Coal Technology (OCT) is to develop the scientific and engineering knowledge base with which industry can bring economically competitive and environmentally acceptable advanced technology for manufacturing synthetic liquid fuels from coal into the marketplace when needed. The technical goal of the Coal Liquefaction Program is to seek advanced and innovative improvements over the state-of-the-art processes for coal liquefaction that can utilize all major parts of the US coal resource base. A technology description and discussion of program goals and strategy is provided in this report. 2 figs.

Energy Technology Data Exchange (ETDEWEB)

Change in structures of 3 kinds of coals with different coal ranks and their deashed coals was studied by heat treatment below 200{degree}C. In experiment, crushed Adaro, Taiheiyo and Huaibei coals below 200mesh and their deashed coals were used as specimens. The coal and deashed coal specimens dried in vacuum at 110{degree}C for 3 hours were filled into an autoclave, and the heat-treated coal specimens were prepared by holding them under initial nitrogen pressure of 2kg/cm{sup 2} at a fixed temperature for 30min. Extraction using pyridine as solvent, volumetric swelling using methanol or benzene as solvent, and measurement of the amount of carboxyl and phenolic hydroxyl functional groups were conducted for these coal specimens. The experimental results are as follows. Huaibei ...

Energy Technology Data Exchange (ETDEWEB)

The main goal of this research is to delineate the wetting behavior of coal and it subsequent effects on fine coal processing. As both bulk and surface properties of coal are interrelated and have a controlling role on the performance of these processes, a detailed study has been undertaken to correlate their influence on both wetting behavior and the response of coal to flotation and other unit operations encountered in fine coal processing. During the last quarter, the effect of coal rank on water retention capacity was investigated. The effect of pH on the vacuum flotation yield and the effect of desliming on the film flotation response of coal were also studied. 6 refs., 5 figs.

British Library Electronic Table of Contents (United Kingdom)

Continually rising energy prices in global markets highlights a serious concern about the need to improve energy efficiency and the efficiency in energy sector in many countries. China, as one of the fastest growing countries in the world and the largest coal producer, has high coal consumption but a low recovery rate of coal utilization. Coal efficiency and the efficiency in coal industry have therefore attracted a great deal of attention from Chinese policy makers, coal firms and academics. This study attempts to compare the relative technical efficiency performance of listed coal mining companies in China and the US using CCR and BCC models in the advanced DEA linear programming. The results show that the level of relative efficiency in Chinese coal mining enterprises, regardless of tot...

Energy Technology Data Exchange (ETDEWEB)

Following the management buy out (MBO) at British Coal`s Hatfield Colliery, a member of the Solicitors involved looks at some of the issues to be considered in coal industry MBO`s. British Coal should be notified, a business plan will be needed for handling venture capital and other issues, and warranties need negotiating.

Energy Technology Data Exchange (ETDEWEB)

The report describes the following: overview of the Russian power industry; electric power equipment of Russia; power industry development forecast for Russia; clean coal technology demonstration program of the US Department of Energy; reduction of coal TPS (thermal power station) environmental impacts in Russia; and base options of advanced coal thermal power plants. Terms of the application of clean coal technology at Russian TPS are discussed in the Conclusions.

Energy Technology Data Exchange (ETDEWEB)

Some applications of magnetic resonance in coal liquefaction research described briefly are: (1) investigation of the nature of carbon deposits on used coal-liquefaction catalysts, (2) determination of the fate of hydrogen during coal liquefaction, and (3) observation of transient free radicals during coal pyrolysis. The first two applications make use of cross-polarization /sup 13/C magnetic resonance combined with magic angle spinning, and the third application is an electron spin resonance study. (BLM)

Science.gov (United States)

Programs in coal research by the Pittsburgh Energy Technology Center are discussed. Topics include: Coal Science and Chemistry, Coal Liquefaction, Alternative Fuels, Coal Preparation, Combustion, MHD Program, Flue Gas Cleanup, Environmental Coordination, and Technology Transfer. (CBS)

Energy Technology Data Exchange (ETDEWEB)

Carboxyl in coal was focused in discussing its pyrolytic behavior while tracking change of its absolute amount relative to the heating temperatures. A total of four kinds of coals, consisting of two kinds brown coals, sub-bituminous coal and bituminous coal were used. Change in the absolute amount of carboxyl due to heating varies with coalification degree. Decomposition starts in the bituminous coal from around 300{degree}C, and is rapidly accelerated when 400{degree}C is exceeded. Carboxyls in brown coals exist two to three times as much as those in bituminous and sub-bituminous coals, of which 40% is decomposed at a temperature as low as about 300{degree}C. Their pyrolytic behavior at temperatures higher than 400{degree}C resembles that of the bituminous coal. Carboxyls consist of those easy to ...

Science.gov (United States)

Finely divided ash-containing coal is immersed in an aqueous solution of hydrochloric acid or citric acid, and acidic ammonium fluoride to cause the ash to react with the acid and the acidic ammonium fluoride, and the deashed coal is thereafter separated from the solution.

Energy Technology Data Exchange (ETDEWEB)

The overall objective of this project was to use molecular genetics to develop strains of bacteria with enhanced ability to remove sulfur from coal, and to obtain data that will allow the performance and economics of a coal biodesulfurization process to be predicted. (VC)

Energy Technology Data Exchange (ETDEWEB)

The article reviews the Rothschild First Interim Report on the future of the British Coal Industry and British Coal Corporation. The report incorporates work undertaken by the Joint Working Groups set up with British Coal. The article points out various errors in the report and criticizes its conclusions.

Energy Technology Data Exchange (ETDEWEB)

The increasing price differential between natural gas and coal will create a demand for technology that can allow the displacement of natural gas with coal in power plants. Coal gasification is the standard approach suggested to allow coal to displace natural gas. However, the relatively high capital investment required for coal gasification will require fuel cost differentials higher than those anticipated in the near term before coal gasification replaces natural gas. One way of achieving shorter term displacement of natural gas by coal would be to develop technology that would allow coal to be used as the heat source for the endothermic reforming of natural gas. In a natural gas-fired combined cycle power plant, the endothermic heat of reforming, which would be provided by coal combustion, is ...

Energy Technology Data Exchange (ETDEWEB)

Three areas have been investigated: coal liquefaction with supercritical fluids, liquefaction by extraction with high boiling liquid solvents, and the production of resins from coal-derived hydrocarbons. The processes are described.

Energy Technology Data Exchange (ETDEWEB)

This article outlines research and progress into the liquefaction of coal by solvent treatment, being conducted at the National Research Institute for Pollution and Resources, Japan. (In Japanese)

Energy Technology Data Exchange (ETDEWEB)

A review of the literature was undertaken to determine the potential for development of instrumentation for on-board remote sensing of coal quality. This review report acts as an inventory of commercially available techniques being tested or under development, particularly in the areas of the cutting horizon measurement methods associated with longwall mining equipment and coal/waste monitoring techniques in coal handling systems. While technology is available which can discriminate rocks from coal on a conveyor belt, the literature indicates that this hardware has yet to be adapted to continuous surface mining machines. 23 refs., 18 figs.

Energy Technology Data Exchange (ETDEWEB)

British Columbia is rich in resources of coal but is deficient in resources of liquid petroleum. The overall objective of the B.C. Research Coal Liquefaction Program is to provide sufficient technical data to identify and evaluate coal conversion opportunities in the province. In this first quarterly report, liquefaction test systems are discussed and results from the testing of equipment, procedures and analytical methods using coal samples from Sukunka (N.E. coal) and Hat Creek (central interior) are presented. The proposed program to be undertaken over the next four years is outlined.

Energy Technology Data Exchange (ETDEWEB)

This paper presents the results of a study commissioned by the British Columbia Science Council to identify opportunities for liquefaction of B.C. coals and to recommend effective approaches to the development of a research program on coal conversion. Contains reviews of British Columbia coal resources to identify prospective candidates for conversion to liquid fuels; of the state of the art in the various processes for the conversion of coal to liquid fuels with particular emphasis on those processes most relevant to British Columbia applications; and of research opportunities in British Columbia for the development of coal liquefaction technology. (16 refs.)

Science.gov (United States)

Results of research programs in coal liquefaction are presented. Areas of research include: desulfurization by bioprocessing; characterization of coal liquefaction processes by XAFS spectroscopy; coprocessing of coal with heavy oil and petroleum residuals; liquefaction research in pyrolysis, catalysis and coal dissolution; novel catalysts; data base development; resource evaluation; depolymerization; solvent extraction and chromatography; correlations of liquefaction yields and coal structure. Individual projects are processed separately for the data bases. (CBS)

Energy Technology Data Exchange (ETDEWEB)

Hydrogenolysis reactions of a mixture of coal liquid and coal liquefaction residue were carried out using red mud - sulfur or Co-Mo/Al{sub 2}O{sub 3} catalyst. The effect of deashing treatment of coal liquefaction residue were also investigated. Notable synergistic effects such as the increase of n-hexane soluble and the decrease of dichloromethane insoluble were observed only with the hydrogenolysis of the basic fraction of coal liquid and nondeashed coal liquefaction residue using red mud-sulfur catalyst. 4 refs., 2 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

The report is the second of three describing the geology of coal quality variations in the foothills and mountains region of Alberta. The Lower Cretaceous Luscar Group, Lower Paleocene Coalspur Formation, and the Upper Paleocene Paskapoo Formation (Obed-Marsh coal zone, which is classified as a foothills deposit) are evaluated. Data on proximate and ultimate analysis variables, calorific analysis, vitrinite reflectance, maceral analyses, and coal quality relationships are presented. The coals range from low volatile bituminous to subbituminous A. Regional and local in seam coal quality variations are examined. 49 refs., 39 figs., 6 tabs.

Energy Technology Data Exchange (ETDEWEB)

Coal bed natural gas (CBNG) development in the Powder River (PR) Basin produces modestly saline, highly sodic wastewater. This study assessed impacts of wetting four textural groups (0-11%, 12-22%, 23 -33%, and > 33% clay (g clay/100 g soil) x 100%))with simulated PR or CBNG water on water retention. Soils received the following treatments with each water quality: a single wetting event, five wetting and drying events, or five wetting and drying events followed by leaching with salt-free water. Treated samples were then resaturated with the final treatment water and equilibrated to -10, -33, -100, -500, or -1,500 kPa. At all potentials, soil water retention increased significantly with increasing clay content. Drought-prone soils lost water-holding capacity between saturation and field capacity with repeated wetting and drying, whereas finer textured soils withstood this treatment better and had increased water-retention capacity at ...

Energy Technology Data Exchange (ETDEWEB)

Ordos Basin, the second largest sedimentary basin in China, contains enormous natural gas resources. Each of the four giant gas fields discovered so far in this basin (i.e., Sulige, Yulin, Wushenqi and Jingbian) has over 100 billion cubic meters (bcm) or 3.53 trillion cubic feet (tcf) of proven gas reserves. This study examines the stable carbon isotope data of 125 gas samples collected from the four giant gas fields in the Ordos Basin. Source rocks in the Upper Paleozoic coal measures are suggested by the generally high {delta}{sup 13}C values of C{sub 2}-C{sub 4} gaseous hydrocarbons in the gases from the Sulige, Yulin and Wushenqi gas fields. The {delta}{sup 13}C values of methane, benzene and toluene in gases from the Lower Paleozoic reservoirs of the Jingbian field indicate a significant contribution from humic source rocks, as they are similar to those in the Upper Paleozoic reservoirs of the Sulige, Yulin and Wushenqi gas fields. However, the wide variation ...

Energy Technology Data Exchange (ETDEWEB)

Organic materials released from energy-related activities could affect human health and the environment. To better assess possible impacts, we developed a model to predict the fate of spills or discharges of pollutants into flowing or static bodies of fresh water. A computer code, Aquatic Pathways Model (APM), was written to implement the model. The computer programs use compartmental analysis to simulate aquatic ecosystems. The APM estimates the concentrations of chemicals in fish tissue, water and sediment, and is therefore useful for assessing exposure to humans through aquatic pathways. The APM will consider any aquatic pathway for which the user has transport data. Additionally, APM will estimate transport rates from physical and chemical properties of chemicals between several key compartments. The major pathways considered are biodegradation, fish and sediment uptake, photolysis, and evaporation. The model has been implemented with parameters for distribution of phenols, an ...

Energy Technology Data Exchange (ETDEWEB)

Traditional methane drainage methods, including conventional ventilation and boreholes drilled in the coal seam, are widely used in modern coal mining operation in China. However, it is often noted that the gas drainage presents low efficiency in most coal mines due to low permeability of the coal seam, which not only affects the safety, but also the productivity of the coal mine. This paper describes the development and application of the waterjet cutting system, which is used to create artificial fractures and increase the permeability of coal seam for the improvement of methane drainage in underground coal mines in China. According to underground monitoring, a significant improvement of methane drainage efficiency of up to 3 to 6 times over the traditional methods has been achieved. (author)

Energy Technology Data Exchange (ETDEWEB)

New York State Electric and Gas Co. (NYSEG) has developed a tool called Coal Quality Engineering Analysis (CQEA) to evaluate the cost impacts of coal quality on its power plants. CQEA allows quantification of the effect of coal quality on plant operating costs and has become an important factor in coal purchasing. The article describes the development of the analysis method, including a logic diagram of CQEA relationships. The results of CQEA calculations on the impact of one coal on overall production costs of different units, the impact of different coals on overall production costs of one unit, and production cost vs. coal quality, are presented and discussed. The use of the CQEA system within NYSEG is described.

International Nuclear Information System (INIS)

The conventional Calzination-Reduction-Carburization (CRC) process offers the potential to manufacture commercial WC powders with median SEM grain sizes below 0.5 pm (ultra fine grades). Strict process control and a high degree of automation have led to increased powder uniformity and high lot-to-lot reliability. The high potential and flexibility of the CRC process is shown by the development of tailor made WC powders with regard to subsequent alloy manufacturing. R and D powders have successfully been processed in full-scale units exhibiting SEM grain sizes of 0.15 - 0.20 pm. This paper discusses the powder characteristics of various ultra fine WC powder grades, stemming from the conventional CRC process. Analytical characterization include also field-emission SEM, bright field TEM, EDX analysis and XRD-line broadening. (author)

Energy Technology Data Exchange (ETDEWEB)

Continually rising energy prices in global markets highlights a serious concern about the need to improve energy efficiency and the efficiency in energy sector in many countries. China, as one of the fastest growing countries in the world and the largest coal producer, has high coal consumption but a low recovery rate of coal utilization. Coal efficiency and the efficiency in coal industry have therefore attracted a great deal of attention from Chinese policy makers, coal firms and academics. This study attempts to compare the relative technical efficiency performance of listed coal mining companies in China and the US using CCR and BCC models in the advanced DEA linear programming. The results show that the level of relative efficiency in Chinese coal mining enterprises, regardless of total technical efficiency or ...

Energy Technology Data Exchange (ETDEWEB)

Continually rising energy prices in global markets highlights a serious concern about the need to improve energy efficiency and the efficiency in energy sector in many countries. China, as one of the fastest growing countries in the world and the largest coal producer, has high coal consumption but a low recovery rate of coal utilization. Coal efficiency and the efficiency in coal industry have therefore attracted a great deal of attention from Chinese policy makers, coal firms and academics. This study attempts to compare the relative technical efficiency performance of listed coal mining companies in China and the US using CCR and BCC models in the advanced DEA linear programming. The results show that the level of relative efficiency in Chinese coal mining enterprises, regardless of total technical efficiency or ...

Energy Technology Data Exchange (ETDEWEB)

10 papers are presented with the following titles: coal fueled diesel engine development update at GE transportation systems; features and performance data of Cooper-Bassemer coal-fueled six-cylinder LSB engine; preliminary test data and systems analysis of a high pressure coal fuel processor/engine system concept; study for coal-water-slurry fuel combustion in a high speed diesel engine; design and operation of a medium speed 12-cylinder coal-fueled diesel engine; progress on the investigation of coal water slurry fuel combustion in a medium speed diesel engine: part 5 - combustion studies; injection characteristics of coal-water slurries in medium speed diesel equipment; coal-water slurry spray characteristics of a positive displacement fuel injection system; novel injector techniques for ...

CERN Document Server

Single-case and Small-n Experimental Designs

Energy Technology Data Exchange (ETDEWEB)

The coal bed methane (CBM) potential of five coal zones (the Kootenay, Gething, Gates, Brazeau, and Coalspur) in the Alberta foothills and mountains is re-evaluated. For evaluation, the coal zones are divided into shallow (200 to 2500 m depth) and deep (over 2500 m depth). The total gas content is estimated. Recommendations on how to obtain more reliable resource data and about producibility are included. 41 refs., 12 figs., 3 tabs., 2 apps.

Energy Technology Data Exchange (ETDEWEB)

This is a collection of photographs of the plant which is now almost completed.

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

Results of tests on the 1 kg/h continuous reactor for the hydroliquefaction of coal are described. The reactor was operated at 415-435 C and 21 MPa using a continuous stirred reactor with a retention time of about 2 hours. All product oils were recovered by distillation. Sub-bituminous coal was found to give the best product yield. Tests using 5% red mud and 3% improved red mud showed significant increases in oil yield. (4 refs.)

Energy Technology Data Exchange (ETDEWEB)

Discussion is presented of world crude steel production, the Japanese steel industry and its expectations of the Canadian coal industry. It is concluded that the Canadian coal industry should pay attention to the trend in customer's requirements regarding coal quality, maintain price competitiveness in the international market place, and remain flexible with regard to the market trend.

Energy Technology Data Exchange (ETDEWEB)

This book presents the papers given at a symposium on occupational safety in coal mines. Topics considered at the symposium included human factors, causes and prevention of personal injuries, remote sensing for ground control, respirable dust generation by continuous miners, accident analysis, hazard analysis of mining equipment, coal mine blasting accidents, coal mine respirable dust sampling, and noise in the mining industry.

Energy Technology Data Exchange (ETDEWEB)

Past and current development of coal utilization technology in the Japanese steel industry is reviewed and some projects currently under research and development briefly described. These include DIOS, an iron making process which directly utilizes both iron ore and coal without a sintering plant or a coke oven; and the development of a new generation coke oven. 15 figs.

Energy Technology Data Exchange (ETDEWEB)

This report attempts to bring together available information on the coal deposits of Antarctica and discuss factors that would be involved if these deposits were to be explored and mined. Most of the reported principal coal deposits in Antarctica lie generally within the Transantarctic Mountains: the majority are of Permian age and are present in the Victoria Group of the Beacon Supergroup. Several other deposits have been recorded in East Antarctica and in the Antarctic Peninsula, including minor occurrences of Mesozoic and Tertiary coal and carbonaceous shale.

Energy Technology Data Exchange (ETDEWEB)

Consol R D is conducting a three-year program to characterize process and product streams from direct coal liquefaction process development projects. The program objectives are two-fold: (1) to obtain and provide appropriate samples of coal liquids for the evaluation of analytical methodology, and (2) to support ongoing DOE-sponsored coal liquefaction process development efforts. The two broad objectives have considerable overlap and together serve to provide a bridge between process development and analytical chemistry.

Energy Technology Data Exchange (ETDEWEB)

The objective of the current MITRE study is to estimate the cost of the coal derived liquid products that result from processing low rank coals in the Wilsonville and HRI CTSL configurations. The resultant cost of liquids is then compared to liquids produced from bituminous coals. The methodology used to accomplish the above objective was to utilize the MITRE coal liquefaction cost model to assess the overall technical and economic performance of low rank coals in both the Wilsonville and HRI configurations. Actual test data from Wilsonville and HRI was used as the basis for these analyses. This test data is modified to simulate complete resid recycle extinction and to standardize the operating performance of the deashing unit. This corrected yield data is then used in the simulation models to predict the overall performance and economics of a conceptual commercial ...

Energy Technology Data Exchange (ETDEWEB)

Energy consumption of black coal mines in Poland and methods for energy conservation are evaluated. Organizational models of energy management in underground coal mining are discussed. Tasks for dispatcher service for energy consumption control in a coal mine are analyzed: control of energy supplies, control of energy consumption, evaluation of electrical failures and reliability of protection systems, recording accidents and analyzing their causes, optimization of power systems in underground mines. Problems associated with control of energy consumption in a coal mine with mechanized systems for coal mining and use of computerized control systems are discussed. Recommendations for reucing energy consumption in underground coal mining are made. 4 references.

Energy Technology Data Exchange (ETDEWEB)

Electrostatic beneficiation of dry coal has received significant attention in the last decade. In this process the coal is ground and then charged, either by corona charging or by triboelectrification (friction charging). Coal and minerals receive different levels of charge -- often opposite polarities in the case of triboelectrification -- and can then be separated based on differences in electrical mobility. Problems associated with the techniques include rapid deposition of particles on the electrodes, thus, effecting further separation. The goal of this project is to optimize the electrostatic coal cleaning process to remove pyrites and inorganic materials through studies of the electrostatic properties of powdered coal, in-situ measurements of the electrodynamics of coal and mineral particles inside the separator, and development of self-cleaning collector ...

Energy Technology Data Exchange (ETDEWEB)

Brown coal resources of the Latrobe Valley in Australia total 140 billion tons to a depth of 975 feet, while economically recoverable reserves have been calculated to total 57 billion tons. Although the coal provides only a very low heating value, about 3300 Btu/lb with 60% moisture content, the enormous seam thicknesses with little overburden allow large scale, open cut mining operations. The low cost and high reactivity of the coal is attracting extensive coal liquefaction research. Research into dewatering processes for the high moisture content brown coal is being conducted. The dried brown coal could be used both domestically and internationally for electricity generation and as an industrial fuel.

Energy Technology Data Exchange (ETDEWEB)

This paper describes an outline of solid fuel production process from brown coal and the investigation results of its elemental techniques. Dried coal is produced by this process which consists of a dewatering of crushed brown coal in oil-based solvent, a solid and liquid separation of slurry, and a remained oil recovery by heating. This process is characterized by the higher thermal efficiency compared with usual drying and the restraint of spontaneous combustion of product coal. It was revealed that solid fuel with low moisture, low ash, low sulfur, and suppressed spontaneous combustion property can be produced from Australian brown coal through this process. From the comparison between kerosene and fuel oil A, it was confirmed that the oil content during dewatering was smaller and the oil recovery by heating was easier by using a solvent with lower boiling point. It was also ...

Energy Technology Data Exchange (ETDEWEB)

Studies are made on coal in terms of its effective utilization, coal cleaning, fluidization and production of new fuel, and issues globally raised. Coal is abundant in reserves and high in supply stability and economic efficiency. However, it is much in CO2 emission per calorific value. To control as much CO2 emission as possible, effective utilization such as increasing of power generation efficiency has been proceeded with. In addition to ultra supercritical pressure and fluidized bed combustion, cited are coal gasification combined cycle power generation and high temperature type fuel cell. Coal has 5-20% ash and impurities like sulfur/nitrogen. Coal should be used clean by pollution abatement measures such as dust collecting, desulfurization and denitrification. Japan is at a world top level of these technologies. Coal is solid, and ...

Energy Technology Data Exchange (ETDEWEB)

In relation to coal liquefaction, the effect of inorganic minerals on liquefaction reactivity and the effect of hydrofluoric acid (HF) treatment on organic molecular structure of coals were studied by demineralization of low-rank coals in HCl or HF solution. In experiment, Taiheiyo coal specimen was deashed in HCl solution at 25-70{degree}C for 6 hours while agitating, and in addition, deashed in HF solution. Hydrogenolysis of the deashed coal specimen was conducted using tetralin or methylnaphthalene as solvent under initial hydrogen pressure of 1.96MPa at reaction temperature of 693K for 60min. The experimental results are as follows. The ash content of Taiheiyo coal hardly offers catalysis in hydrogenolysis reaction. Carboxyl group increases in demineralization of coal because of breakage of bridged bonds. Organic structure of ...

Energy Technology Data Exchange (ETDEWEB)

In order to develop a high-efficiency coal pyrolysis method, flash pyrolysis was experimented on slurry prepared by using liquid-phase oxidation reformed coal and a methanol-based solvent mixture. Australian Morwell coal was used for the experiment. The oxidized coal, into which carboxyl groups have been introduced, has the condensation structure relaxed largely, and becomes highly fluid slurry by means of the solvent. Char production can be suppressed by making the oxidation-pretreated coal into slurry, resulting in drastically improved pyrolytic conversion. The slurry was divided into dissolved solution, dried substance, extracted residue, and residual slurry, which were pyrolized independently. The dissolved solution showed very high conversion. Improvement in the conversion is contributed by separating the dissolved substances (coal macromolecules) at ...

Science.gov (United States)

The method of producing blast furnace coke by (1) compacting a finely divided coal wherein at least about 60% by weight of the coal has a diameter of less than about 1/8 inch to form a coal compact, which compact immediately after removal from the compacting means comprises at least about 20% by weight of particles having a particle size of less than 1/4 inch in diameter; (2) breaking the thus formed compact such that the bulk density is sufficiently increased to be capable of conversion into coke suitable for use in large blast furnaces upon carbonization thereof; and (3) carbonizing the broken compact to thereby produce blast furnace coke having a minimum hardness of about 68 and a minimum stability of about 55. The compacting is preferably performed at a pressure equivalent to that achieved by passing the finely divided coal between rolls at a pressure applied to the coal of ...

Science.gov (United States)

According to W. H. Wiser and A. G. Oblad, the program at the University of Utah to develop coal conversion techniques, which has received federal grants of $1.35 million since 1969, recently was awarded $425,000 from the U.S. Office of Coal Research for the development of catalysts for coal conversion and low-sulfur fuel oil production. In tests, 100 lb of coal have been converted into 95 lb of products composed of 30 lb liquid fuel like gasoline, 5 lb of diesel or fuel oil, 30 lb of gaseous fuel, and 30 lb of char.

Energy Technology Data Exchange (ETDEWEB)

McLeod River Coal Ltd., a wholly owned subsidiary of Manalta Coal Ltd., has received Alberta Energy Resources Conservation Board approval to establish an open pit coal mine and plant in the northwest portion of the Coalspur field, east of Hinton. McLeod proposes to produce up to 4.2 million tonnes/year of thermal coal for 40 years, starting in 1985. The commercial viability of the project must be assessed before construction starts at the McLeod River site. The Board's ruling is subject to provincial cabinet approval.

Science.gov (United States)

Research programs on coal and coal liquefaction are presented. Topics discussed are: coal science, combustion, kinetics, surface science; advanced technology projects in liquefaction; two stage liquefaction and direct liquefaction; catalysts of liquefaction; Fischer-Tropsch synthesis and thermodynamics; alternative fuels utilization; coal preparation; biodegradation; advanced combustion technology; flue gas cleanup; environmental coordination, and technology transfer. Individual projects are processed separately for the data base. (CBS)

Energy Technology Data Exchange (ETDEWEB)

A study has been made of the reactor blockages occurring in the course of direct hydroliquefaction of Miike coal, Taiheiyo coal and Yallourn coal briquets in a tubular reactor. The liquefaction tests were carried out at 450 C under 24.6 MPa hydrogen pressure, with red mud and sulfur catalyst. From the observed balances for catalyst and coal ash, it was inferred that reactor blockages are due to sedimentation of catalyst and ash. The conditions for catalyst and coal ash run-off were determined after solvent and slurry flow rates had been altered to suit the type of coal being tested. It was found that ash run-off occurred more readily as the difference between the slurry flow velocity and the natural sedimentation velocity of red mud in the coal liquids increased. Even when ash run-off was occurring, however, the ash concentration of the ...

Energy Technology Data Exchange (ETDEWEB)

In 1970, the Federal Power Commission predicted a fall from 46% to 27% in 1990 as a result of predicted increases in the use of nuclear power. Today, the Department of Energy expects coal to supply about 50% of electricity generation in 1990. About one-eighth of the world's annual hard coal production is used to make electricity in the United States. Power stations in the country used more coal in 1979 than was produced in the whole Western Europe that year. These 405,000,000 tons of coal equivalent were burned in 1257 individual utilities with an aggregate capacity of 235,000 megawatts. There are coal-fired power plants in 43 of the 50 states. Four factors will be most important in shaping the future development of coal-based electricity: prices, conservation, environmental regulations, and national security. The price differential between ...

Energy Technology Data Exchange (ETDEWEB)

In the wide range from brown coal to anthracite, an investigation was made of effects of heat treatment on physical/chemical properties and of coal rank dependence. For the experiment, 12 kinds of coal samples were used, and for heat treatment, the fluidized bed heated by the electric furnace and the infrared-ray gold image furnace were used. To examine characteristics of the heat-treated coal char, conducted were oxygen gasification, TPD measurement, XRD measurement, alkali metal measurement, and pore distribution measurement. The following were obtained from the experiment. The gasification reaction rate of the char heat-treated in the temperature range between 900{degree}C to 1700{degree}C decreases with a rise of the temperature of heat treatment, and the degree of decrease in the rate depends on coal rank. The order of gasification rate between coal ranks ...

Energy Technology Data Exchange (ETDEWEB)

This quarterly report for the period July through September 1984 summarizes activities in Sandia National Laboratories' continuing program of coal liquefaction research. The primary goals are to: explore novel catalytic concepts and materials for conversion of coal to liquid fuels; determine the effects of process variables on catalyst deactivation; determine the effects of coal structure and solvent properties on low temperature dissolution; study the kinetics and catalysis of hydrogen transfer reactions; develop an understanding of slurry gelling phenomena; and provide a technical assessment of coal liquefaction processes. During this period, work was performed on: the rheology of Illinois No. 6 coal in hydrogenated creosote oil; dissolution chemistry of subbituminous coal; pyrite catalysis; liquefaction of Illinois No. 6 coal in ...

Energy Technology Data Exchange (ETDEWEB)

The primary purpose of the pilot Coal Compilation Project is to provide coal resource maps to stimulate and support industry exploration programs and to assist government in matters of resource management. An essential feature of the program is the use of cost effective Geoscience Information System (GSIS) technology that allows the database and various thematic maps to be analysed, updated and displayed with complete flexibility at any scale. This report describes the main features (geology, resource management, exploration history, coal occurrences etc.) of the study area, mapsheet NTS 83E/9 (Moberly Creek), and includes a copy of the 1:50,000 scale map produced. The study area is located in West-central Alberta and contains coal measures deposited amid thick successions of sandstones, siltstones, shales and conglomerates. These coal-bearing sequences are part of the Luscar Group, ...

Science.gov (United States)

A method of producing blast furnace coke from bituminous coals, particularly coals having poor coking capacities in which the coal to be carbonized is ground, predried or preheated, mixed with binders, compressed or formed into briquets having small mechanical resistances and charged into oven chambers, is characterized by fine coals or fine coal mixtures having a swelling index in mixture according to DIN 51741, smaller than 7, and preferably, below 6, and comprising more than 50% of poorly or non-baking coal having a content of volatile matter in excess of 30% or less than 20% which coals or coal mixtures are ground up to attain a surface per unit mass, according to DIN 66145, of from 400 cm/sup 2/ to 1200 cm/sup 2/ per gram, with from 3% to 8% by weight of organic binders, compressing the mixture to form it into a ...

Energy Technology Data Exchange (ETDEWEB)

In Canada, the federal government, through CANMET, is actively supporting coal liquefaction research and development in a number of areas. A review of the basic principles and some of the processes in the production of liquid fuels from coal is presented with reference to the characteristics of the Canadian coal resource base. An overview of the CANMET coal liquefaction contract program is presented and specific results from the batch autoclave studies carried out with Saskatchewan lignite and Nova Scotia high-volatile bituminous coals are discussed. The development of a laboratory-scale continuous-flow coal liquefaction unit at the Energy Research Laboratories of CANMET to investigate the co-processing of coal and bitumen/heavy oil is also described. In principle, there are only two routes to the production of liquid fuels from ...

Energy Technology Data Exchange (ETDEWEB)

Concepts involving combined gas-turbine/steam-turbine power-generation plants, in which the fuel gas for the gas turbine is produced via the gasification of coal, are now extremely advanced. This technology already permits efficiencies of around 50% current development targets view 65% as achievable. In conventional technology, efficiencies are tied to conditions, such as air and cooling-water temperatures, at the particular location. In combined-cycle power plants, the properties of the fuel coal also play an important part. There are, in face, coals which can be more advantageously used in a combined-cycle power plant than in a conventional one. These differences, combined with advantageous concepts for coal-fired combined-cycle power-generating plants, are presented and analyzed. Particular attention is devoted to individual losses occurring at coal conversion, thermodynamic ...

Energy Technology Data Exchange (ETDEWEB)

The Science Council accepted the recommendations of the Swan Wooster report on Opportunities for coal liquefaction research in British Columbia, Vancouver, BC, Canada, Science Council of British Columbia, 173 pp (May 1980), following review by the Sub-committee on Coal Research. The Sub-Committee has recommended a four year Research and Development programme on B.C. coals to be carried out at B.C. Research Council. About 5 million dollars would be spent during the four year period. The overall objective is to provide sufficient technical data to identify and evaluate coal conversion opportunities in B.C. A significant secondary objective is to provide a group of trained engineers and scientists in the Province familiar with the technology of coal conversion. (1 ref.)

Science.gov (United States)

Objectives of the program are to understand the mechanisms of coal liquefaction, to determine the role of catalysts in the direct conversion of coal to liquids, to determine the mechanism of catalyst deactivation and to explore slurry phase catalyst systems. Specific projects include: short-contact time coal liquefaction, mineral matter effects and catalyst studies. During this period, work was performed on: (1) the stability, at reaction temperature, of a recycle solvent obtained from the Lummus Two Stage Liquefaction facility, (2) reactions of preasphaltenes and asphaltenes prepared under various reaction severities, (3) the evaluation of the catalyst level detector installed at the H-Coal facility, (4) the characterization of oil soluble metal compounds with respect to hydrogenation activity, and (5) characterization, deactivation and regeneration of catalysts obtained from both the ...

Energy Technology Data Exchange (ETDEWEB)

This BCRS project demonstrates the use of SAR interferometry for measuring and monitoring land subsidence caused by underground coal fires and underground mining in a remote area of north west China. China is the largest producer and consumer of coal in the world. Throughout the N.W., N. and N.E. of China, the coal-seams are very susceptible to spontaneous combustion, causing underground coal fires. As the thick coal seams are burned out, the overburden collapses, causing land subsidence, and producing new cracks and fissures, which allow more air to penetrate and continue the fire to spread. SAR interferometry, especially differential interferometry has been shown to be able to measure small differences in surface height caused by such land subsidence. This report describes the problems, the test area, the procedures and techniques used and the results obtained. It concludes with a ...

Energy Technology Data Exchange (ETDEWEB)

The coal transportation industry has played an integral role in determining coal markets, particularly in recent years, as the industry has evolved from cost-based pricing to market-based pricing. Aggressive pricing by Western rail carriers has caused extensive changes in coal marketing patterns in the Midwest. Multi-modal barge deliveries of Western and Appalachian coals have also played a significant, though lesser, role in changing coal markets. Eastern rail carriers have generally lagged in their aggressive pursuit of new coal markets and, to date, few changes in coal markets have been realised. The historic dominant role of transportation in shaping markets for coal will continue into the future as the utility industry contends with the effects of CAAA compliance and deregulation and as the coal ...

Energy Technology Data Exchange (ETDEWEB)

The first part of the conference dealt with environmental effects of using coal. Papers dealt with the use of fly ash in agriculture and its effect on plant growth; the effect of airborne emissions on fish and wildlife resources, on watersheds, and on airsheds; the effects of surface mining on the ecology; blast effects; and health hazards associated with coal. The session on policy studies addressed the issue of cost of synthetic fuels and discussed the state and federal pollution regulations on burning coal and waste disposal. The session on combustion presented papers on atmospheric and pressurized fluidized-bed combustion for industrial and utility boilers. It also included papers on MHD power plants, coal-oil and coal-water mixtures, emission characterization and control, and catalytic combustors. The design of gasification plants, reaction kinetics, specific heats of ...

Energy Technology Data Exchange (ETDEWEB)

This paper discusses spectral change in brown coal and bituminous coal as a result of low-temperature drying. The experiment used a Fourier transform infrared (FT-IR) spectroscopy disposed with an in-situ diffuse reflector as a water content measuring method. The FT-IR spectra of coal showed the existence of two types of adsorbed water. One of the two spectral peaks was thought to have been caused by isolated water molecules which may have been hydrogen bonded to hydrocarbon in the coal molecules and weakly bound. The other peak was thought to have been caused by water which may have been hydrogen bonded to functional groups such as hydroxyl groups in the coal molecules and strongly bound. Drying behavior in brown coal and bituminous coal showed the absorption peak at 3640 cm[sup -1] reducing faster than the absorption peak at 3360cm[sup ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

The properties of cast basalt and alumina are examined. The ways in which these materials have been used in applications in coal preparation plants, for example in bunker and pipe linings where abrasion and corrosion resistant materials are required, are discussed.

Science.gov (United States)

The extensive reserves of mined coal types, their great variety and the complexity of the composition and properties, as well as their important role as an energy fuel and industrial feedstock, cause one to give special attention to their classification. Of course, one of the principal fields of technological processing of coal is coking. In addition to the production of blast furnace coke, in the future specialized plants will be developed for production of coke and other carbonized materials for non-blast-furnace processes (electrothermal processes, production of calcium carbide, ferroalloys, zinc, yellow phosphorus, copper, etc.). One important area is new nonfuel uses, including a number of processes for processing of coal feedstocks to obtain a wide range of carbonaceous materials (coal-graphite products, carbon black, adsorbents, etc.), liquid fuels, and chemical products. In choosing a given area ...

Energy Technology Data Exchange (ETDEWEB)

A schematic diagram of the decision making process for air pollution control equipment for the conversion of a fossil-fired generating unit from oil to coal is presented and explained.

Energy Technology Data Exchange (ETDEWEB)

In order to replace industrial cobalt and nickel and molybdenum catalysts, more economical catalysts, red muds, are used. Comparative data about the chemical, structural and thermal properties of different samples of red muds, which are important for catalytic hydrogenation, are cited. The different conditions for hydrogenation of coals in a reactor are examined.

Energy Technology Data Exchange (ETDEWEB)

The paper reported on an experiment on measurement of concentration of highly concentrated coal slurry using microwaves carried out at Miike coal preparation works. The purpose of the experiment was to investigate applicability of microwave moisture content measurement of slurry of a mixture of coal and coal particles and to use it to the control of process such as coal preparation and processing. In the experiment, a method for measuring the slurry concentration was adopted in which the container filled with highly concentrated coal slurry was irradiated with microwaves and the damping of strength of the penetrating microwaves was detected. As a result of the experiment, it was found out that there was a big correlation between the capacitive concentration of slurry and the damping ratio of microwaves. When irradiating slurry with microwaves of 1GHz frequency, ...

Energy Technology Data Exchange (ETDEWEB)

Taiheiyo coal deashed using acid treatment and loaded with potassium or calcium was hydro-cracked under gaseous phase to discuss effects of these metals on liquefaction reaction. In addition, the loaded coal was added with red mud catalyst to examine effects of the addition. The loaded potassium has a softening power, and particularly the potassium adsorbed into surface and micropores in the coal decomposes selectively HI-BS and BI-PS and generates gas and HS. On the other hand, potassium deposited on coal surface promotes direct gas production from the coal. Irrespective of its loading modes, calcium has a catalytic nature to produce HI-BS selectively. Calcium also acts to impede decomposition of HI-BS into HS. Adding red mud catalyst to potassium loaded coal increases the inversion rate and the liquefaction yield, and most of the increase is accounted for by ...

Energy Technology Data Exchange (ETDEWEB)

The report details the results of a series of large-scale experiments where small coal fires were used to ignite conveyor belting at air velocities ranging from 0.76 m/s to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited conveyor belting located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flame coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two ...

Energy Technology Data Exchange (ETDEWEB)

This progress report presents a detailed description of the background, technology and application, and Statement of Work for the development of a coal-fired pulse combustor for residential space heating.

Energy Technology Data Exchange (ETDEWEB)

Significant progress was made in the May 1990--May 1991 contract period in three primary coal liquefaction research areas: catalysis, structure-reactivity studies, and novel liquefaction processes. A brief summary of the accomplishments in the past year in each of these areas is given.

Wastenet

... After completing a review into direct coal liquefaction research carried out in Australia and internationally, CSIRO has identified potential new science and technology developments that may improve the cost and viability of CTL in a greenhouse gas-constrained environment. We are conducting research to: determine the optimum ...

Energy Technology Data Exchange (ETDEWEB)

The Coal Quality Engineering Analysis (CQEA) program developed by the New York State Electric and Gas Company (NYSEC) calculates the as-burned cost of burning a specific coal in a specific generation unit. These costs include: maintenance costs for coal and ash handling equipment; ash disposal costs; cost of oil (if required for flame stability and/or derating because of pulverizer capacity limitation); flue gas desulfurization costs; cost of replacement power caused by pulverizer, precipitator fly ash collection and bottom ash capacity limitation; boiler losses due to moisture, hydrogen, dry gas and unburned carbon; power for coal and ash handling equipment; power for coal pulverizers; cost of using excess air to prevent slagging of coal with low ash softening temperatures; and effect of heat rate on coal tonnage required for a desired ...

Science.gov (United States)

The manual describes a combined coal-cleaning and flue gas desulfurization (FGD) computerized design and cost-estimate model and gives detailed procedures for using it. All inputs and outputs are described, as well as the various options available. Design and economic premises ar...

Energy Technology Data Exchange (ETDEWEB)

Many Pacific Basin countries rely on oil for electricity production. Alternative fuel sources such as coal, which is available in the Pacific Basin, can help mitigate adverse impacts of sudden price increases or supply disruptions. Coal combustion produces solid and potentially hazardous wastes of concern to environmental regulators and utility managers. This paper identifies issues associated with managing coal combustion wastes in the Pacific Basin, using the state of Hawaii as a case study. Hawaii is typical of many Pacific Basin locations in that it depends on oil, has limited sites, for waste management operations, and is subject to domestic and international waste management regulations. The paper discusses coal-fired utility wastes, environmental impacts of coal combustion waste disposal, and regulatory requirements that impact coal waste management. From ...

Energy Technology Data Exchange (ETDEWEB)

Recent research at the laboratory scale by a number of organizations in different countries has shown that with the use of particular types of solvents it is possible to achieve almost complete conversion of coal to liquid products under relatively mild process conditions. This work is reviewed and the conclusions to be drawn from it are summarized.

Science.gov (United States)

The objectives of this project are to support the DOE direct coal liquefaction process development program and to improve the useful application of analytical chemistry to direct coal liquefaction process development. Independent analyses by well-established methods will be obtained of samples produced in direct coal liquefaction processes under evaluation by DOE. Additionally, analytical instruments and techniques which are currently underutilized for the purpose of examining coal-derived samples will be evaluated. The data obtained from this study will be used to help guide current process development and to develop an improved data base on coal and coal liquids properties. A sample bank will be established and maintained for use in this project and will be available for use by other researchers. The reactivity of the non-distillable resids toward ...

Energy Technology Data Exchange (ETDEWEB)

This paper introduces a new method to produce nano-composite powder for the preparation of high performance ZnO varistors. ZnO particles were coated with Bi{sub 2}O{sub 3}, Sb{sub 2}O{sub 3}, Co{sub 2}O{sub 3}, Cr{sub 2}O{sub 3} and other additives via liquid nano-coating technique. Then the prepared powder was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermal gravity and differential scanning calorimetry (TG-DSC) and particle size distribution. The results showed that the ZnO composite powder is homogeneously coated and ultrafine. The densification, phase composition and microstructure of ZnO varistors was studied by linear shrinkage, X-ray diffraction (XRD) and SEM, respectively. The preliminary electrical parameters of ZnO varistors showed that the breakdown voltage V {sub b} (1 mA/cm{sup 2}) and nonlinear coefficient {alpha} is 5400 V/cm and 50, respectively, much higher than that of conventional ball milling ...

Energy Technology Data Exchange (ETDEWEB)

This paper discussed the potential of biofuels with particular reference to the situation in Germany and Europe. Emphasis was on technical potential, such as biofuel production, utilization and environmental aspects. The Institute of Agricultural Technology and Biosystems Engineering ran vTI emission tests on diesel engines to evaluate the environmental impacts of biofuels. This testing facility is able to drive heavy-duty diesel engines in both stationary and dynamic test cycles, such as the European ESC and ETC. Additional analyses were conducted to determine the fine and ultra-fine particles, polycyclic aromatic hydrocarbons (PAH), aldehydes, ketones, and the usual regulated exhaust gas compounds. Ames tests were conducted to assess the mutagenic potential of tailpipe emissions. Previous study results showed that neat vegetable oils can render the exhaust high in mutagenic potency. Some of the non-regulated exhaust gas compounds were found to vary nonlinearly ...

International Nuclear Information System (INIS)

The present work focuses on the transformation of high-purity Ni powder blends of controlled volume fractions (40 and 60 %) of nanometre-sized (100 nm) and micrometre-sized (544 nm) particles into bulk samples as part of a strategy for producing ultrafine-grained materials usefully exhibiting both strength and ductility. The process involved cold isostatic pressing at 1.5 GPa and sintering. The resulting bulk samples had relative densities near 95 %, were texture-free, and exhibited two different grain size distributions with an average value of 600 #+-# 30 nm. The mechanical properties were investigated by compression and microhardness tests, both at room temperature, and compared to the behaviour of a sample processed from micrometre-sized powder only. Samples prepared from the blends exhibited high yield stresses of 440 and 550 MPa after compression, and they did sustain work hardening. Tests conducted before and after compression up to 50 % deformation showed ...

Energy Technology Data Exchange (ETDEWEB)

Supermetal with critical characteristics is under advanced investigation for further improvement of metal materials. Although iron is most frequently used as structural material among various metals, it should be used more carefully and effectively because of resource limitation and global environmental problem. It is essential to draw various excellent properties much more from iron and to improve recyclability. In particular, the best way to meet these requirements is achievement of more fine structure and higher purity. Since the lowest crystalline grain size is now limited to nearly 10{mu}m, metallic structure composed of grains below 1{mu}m is expected by mesoscopic control. Various methods have been studied to achieve ultra-fine crystalline structure, and study of precise heat treatment control and ultra-strength metallurgy is required. Heat treatment in magnetic field and layered structure by mechanical alloying are also promising. Drastic enhancement of ...

Energy Technology Data Exchange (ETDEWEB)

It has been discovered that when Taiheiyo coal pulverized to 200 mesh or smaller is dispersed in naphthalene, a non-hydrogen-donor solvent, and reacted under hydrogen pressure in the presence of a red mud/sulfur catalyst, the catalyst exhibits activity in the regeneration of hydrogen donor solvents which have been hydrogen-depleted in the course of coal liquefaction. It is already known that inorganic matter contained in coal acts as a catalyst in liquefaction. This suggests that the reported effect of the red mud/sulfur catalyst is due to the iron oxide reacting with the sulfur and forming pyrrhotite. 22 refs., 6 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

Environmental studies in slip-stream process development units at SCGP-1, Shell's advanced coal gasification demonstration plant, located near Houston, Texas, have demonstrated that the gas and water effluents from the Shell Coal Gasification Process (SCGP) are environmentally benign on a broad slate of coals. This report presents the results of those environmental studies. It contains two major subjects, which describe, respectively, the experiments on gas treating and the experiments on water treating. Gas treatment focused on the performance of aqueous methyldiethanolamine (MDEA) and sulfinol-M. 8 refs., 24 figs., 13 tabs.

Science.gov (United States)

A method of making high strength coke briquettes suitable for use as blast furnace coke comprising, (A) providing coal, (B) heating the coal at a temperature at or above the softening point of the coal to form partially carbonized char, (C) cooling the partially carbonized char below the softening point of the coal, (D) mixing the cooled partially carbonized char and tar to form a mixture of tar and partially carbonized char, (E) briquetting the mixture of tar and partially carbonized char to form briquettes of tar and partially carbonized char, (F) calcinating the briquettes to form high strength briquettes.

Energy Technology Data Exchange (ETDEWEB)

An improved process is disclosed for reducing the water content of coal containing bound water by releasing at least a portion of the bound water by maintaining the coal at a temperature from about 220/sup 0/ to about 500/sup 0/ F. in the presence of water at a pressure sufficient to maintain at least portion of the water in a liquid phase for a time sufficient to release at least a portion of the bound water wherein the improvement comprises contacting the coal during such treatment with an active material selected from the group consisting of carboxylic organic acids containing up to about 6 carbon atoms, phenol, phenolic acids and inorganic acids.

Energy Technology Data Exchange (ETDEWEB)

The US DOE is calling on the nations' industries and academic institutions to develop a new approach for converting coal into liquid fuels at costs that can be competitive with imported oil. Based on a number of innovations, the department is looking for new approaches that can substantially reduce the cost of liquids from coal, essentially capping the price of imported oil. If successful, the new process will define the next generation of coal liquefaction technology and represent a dramatic improvement over the current state-of-the-art integrated two-stage process. 1 fig.

Energy Technology Data Exchange (ETDEWEB)

In order to improve the handling capability of red mud, it is mixed with fine-grain coal material such as brown coal or lignite in dust form, in a ratio by weight of between 0.5-10:1. The liquid present in the red mud is bound by the very fine coal admixed therewith so that the resulting mixture can be stored in a silo and even pneumatically conveyed, and the oily properties of the red mud are removed by the treatment. The mixture is particularly suitable for use in connection with the hydrogenating liquefaction of coal in which the red mud is used as a catalyst.

Science.gov (United States)

This bulletin traces development of high-pressure, coal and tar hydrogenation technology, based on an intensive review of pertinent literature. The bulletin written as part of the Bureau of Mines research program on synthetic liquid fuels covers the history and economics of the process; chemical aspects of hydrogenation of coal, tar, and middle oil; engineering aspects of converting coal and tar to liquid fuels, principally gasoline; and equipment for the process. The literature covered includes documents of United States and British governments, journals, and other publications. Bureau results in the hydrogenation field are also incorporated.

Science.gov (United States)

This report--the forty-fifth of a series--is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives to oil and gas as sources of clean energy. The projects reported this month include those for coal conversion process development, materials engineering, alkali metal vapor topping cycles, a coal equipment test program, an AFB coal combustor for cogeneration (CCC), engineering and support studies, process and program assistance, evironmental assessment studies, magnetic beneficiation, and AFBC demonstration plant.

Energy Technology Data Exchange (ETDEWEB)

Denison Mines Limited is completing two final feasibility studies on the Coalspur thermal coal property in northwestern Alberta and the Belcourt property south of Dawson Creek, B.C. Denison is also carrying out a geological field program on a promising metallurgical coal property, Wildhay, west of Hinton, Alberta. Fording Coal Ltd. will close its Fording River mine for at least the second half of December. Site preparation has started at the Obed-Marsh thermal coal project northeast of Hinton.

Energy Technology Data Exchange (ETDEWEB)

The first stage of the continuous coal hydrogenation unit has been used to test a number of coals with different processing strategies. This work has shown that conversion increases with product recycle, however after the second pass the increase is small but operability of the reactor is considerably improved. A kinetic model for the aromatic saturation of the recycle solvent in the second stage has been developed and will be used in the selection of conditions for oil upgrading processes. New insights into the structural composition of coal derived materials have been made due to the refinement of chromatographic or solubility separation analyses into routine operations and the development of a new technique in NMR spectroscopy.

Energy Technology Data Exchange (ETDEWEB)

Consol R&D is conducting a three-year program to characterize process and product streams from direct coal liquefaction process development projects. The program objectives are two-field: (1) to obtain and provide appropriate samples of coal liquids for the evaluation of analytical methodology, and (2) to support ongoing DOE-sponsored coal liquefaction process development efforts. The two broad objectives have considerable overlap and together serve to provide a bridge between process development and analytical chemistry.

Energy Technology Data Exchange (ETDEWEB)

This publication, part of the series titled Market Guide for Steam Coal Exports from Appalachia provides information on export markets, contracts, and related matters for producers and others involved in mining, selling, and shipping Appalachian coal to foreign buyers. It also includes information on the financial institutions that provide export finance and how they are used. Senior officers of more than 40 banks ranged from the largest money center bank and a major foreign bank in New York City to small banks in Appalachia.

Energy Technology Data Exchange (ETDEWEB)

Light microscopy was used to analyze the effects of added catalyst at different conditions (temperature and reaction times) in liquefaction testing of a low pyritic sulfur bituminous coal. Quantitative changes in vitrinite/vitroplast reflectance of coal and liquefaction residues were shown to be useful markers in analyzing and understanding the role of catalyst during the initial stage of coal particle hydrogenation. Lower reflectance values corresponded to increased conversions up to about the 60 min and 375{degrees}C experimental conditions. Microscopical observation of liquefaction residues also revealed the presence of `wall scales` of varying width.

Energy Technology Data Exchange (ETDEWEB)

A discussion of the Sasol I, II, and III coal liquefaction plants of the Republic of South Africa was presented. The technology, capacity, and economics of these projects were included in the discussion. These plants utilize the Fischer-Tropsch process of indirect coal liquefaction and produce a barrel of synthetic crude for about $55 (or about $20 above current market prices). Outlines of the differences in indirect coal liquefaction and newer direct methods were presented. It was determined that the South African dedication to coal liquefaction was made more for the political aspects of energy independence than economics.

Energy Technology Data Exchange (ETDEWEB)

The theme of the conference was 'The paradox: today's coal technologies versus tomorrow's promise'. The sessions covered: today's technologies, tomorrow's potential; economic stability; energy security; transition to sustainable energy future; new coal power technologies leading to zero emission coal; existing power plants - improved performance through use of new technology; and carbon capture and storage R & D - challenges and opportunities. Some of the papers only consist of the viewgraphs/overheads.

Energy Technology Data Exchange (ETDEWEB)

The composition, rank, coal facies, and coal pore structure characteristics of 15 coal samples were investigated systemically using methods of lithotype analysis, maceral analysis, proximate analysis, mercury porosimetry analysis, and nitrogen adsorption analysis. These samples were directly collected from the working faces of No.4, 8, 9 seams in Liulin district, eastern margin Ordos Basin, China. Four types of paleoenvironment including a wet forest swamp, an intergradation forest swamp, a drained forest swamp, and a fresh-water peat swamp were distinguished by lithotype and merceral analysis. An R-cluster analysis was performed to demonstrate the correlations between the coal facies and the pore structures. The results showed that coal rank is the primary factor affecting the development of micropores and transition pores, whereas coal facies control the ...

Energy Technology Data Exchange (ETDEWEB)

In Germany, the oil crisis of 1979 initiated a revival of coal liquefaction technologies which had already seen industrial-scale application in the early 1940s. The paper describes various coal liquefaction research projects carried out and pilot plants constructed in Germany since then. 18 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

This article discusses the latest developments made in the field of technology used for coal liquefaction. Some new areas of development in research and development work are described. Particular consideration is given to low-severity processing. This has two advantages, mostly low-molecular-weight fragments are produced and the extracts are low in heteroatoms. A detailed description of low-severity processing is given. The refining of the liquids produced from coal is also covered.

Energy Technology Data Exchange (ETDEWEB)

The possibility of modifying the functional composition of humic acids by gas-phase ozonation of bed-oxidized brown coal was examined. About 90% of the organic matter of brown coal was converted to low-molecular weight soluble oxygen-containing products by stepwise liquid-phase ozonation (in chloroform and acetic acid).

Science.gov (United States)

Research is being carried out in this project in two areas which are of interest to ongoing investigations at the Pittsburgh Energy Technology Center (PETC). They are: (a) thermal behavior of slurry reactors used for indirect coal liquefaction; and (b) coal liquefaction under supercritical conditions. The current status of each of these tasks is summarized in this report. 76 refs., 23 figs., 6 tabs.

Energy Technology Data Exchange (ETDEWEB)

The Nova Scotia Research Foundation Corporation was established in 1946 by the Province of Nova Scotia to use science and technology to assist in the economic development of Nova Scotia. Within the Applied Science Division of the Corporation, research and development programs in the area of coal and mineral technology have been undertaken. A brief description of two projects -- coal liquefaction and coal-water fuels, are reported.

Energy Technology Data Exchange (ETDEWEB)

Treatment of coal with H/sub 2/O/sub 2/ in presence of formic acid allowed complete destruction of organic matter in 15-72 h (depending on coal rank etc.), giving mineral matter contents in good agreement with those of low temperature ashing (a much slower process.

Energy Technology Data Exchange (ETDEWEB)

Denison Mines Ltd. own extensive coal properties in British Columbia and Alberta. The geological settings, the reserves and the coal quality are described. The most important is the Quintette property where four opencast mines are currently being developed. Other sites in British Columbia are Belcourt and Saxon, and in Alberta, Coalspur.

Energy Technology Data Exchange (ETDEWEB)

The externally fired combined cycle is emerging as an economically viable repowering options for old non-competitive coal fired steam plants. This paper describes the initial operation of a pilot plant located at Kennebunk, Maine and the initial work on the repowering of a 48MW coal fired steam plant located in Warren, PA.

Energy Technology Data Exchange (ETDEWEB)

In this first quarterly technical report for DOE Contract No. DE-AC22-87PC79654, a description of the background, technology, and application is provided. The design and fabrication of advanced combustion chambers were completed during this period. Initial testing on both the bare metal and refractory lined advanced chambers were initiated. The units were tested initially with gas but primarily with coal. A Pittsburgh No. 8 pulverized coal was used for these test activities. Both advanced chambers pulsed well.

Energy Technology Data Exchange (ETDEWEB)

New Brunswick has appreciable fossil-fuel reserve potential, particularly in oil shales and to a lesser extent in high-sulfur coal. Each of these resources on their own, however, has problems which could restrict their development. To offset these problems it is proposed that coal and oil shale resources can be used together to overcome these difficulties and effect an attractive, economically viable, energy recovery system. One way is o use coal/oil shale blends, rather than the more conventional coal/limestone mixtures, as feed to fluid-bed combustors for steam generation. The sulfur from the coal is fixed on the spent shale, with the shale combustibles contributing to thermal output. Similarly, oil shale can be used in place of limestone as a combustion scrubber medium to clean emissions from existing conventional coal-fired plants. Several scenarios for the ...

Science.gov (United States)

Processing concept that increases supply of jet fuel has been developed as part of study on methods for converting coal to hydrogen, methane, and jet fuel. Concept takes advantage of high aromatic content of coal-derived liquids to make high-octane gasoline, instead of destroying aromatics to make jet fuel.

Energy Technology Data Exchange (ETDEWEB)

A C.sub.5 -900.degree. F. (C.sub.5 -482.degree. C.) liquid yield greater than 50 weight percent MAF feed coal is obtained in a coal liquefaction process wherein a selected combination of higher hydrogen partial pressure, longer slurry residence time and increased recycle ash content of the feed slurry are controlled within defined ranges.

Science.gov (United States)

A potentially new use for Illinois coal is as a fuel injected into a blast furnace to produce molten iron as the first step in steel production. Because of its increasing cost and decreasing availability, metallurgical coke is now being replaced by coal injected at the tuyere area of the furnace where the blast air enters. The purpose of this study is to evaluate the combustion of coal during the blast furnace injection process and to delineate the optimum properties of the feed coal. This investigation is significant to the use of Illinois coal in that the limited research to date suggests that coals of low fluidity and moderate to high sulfur and chlorine contents are suitable feedstocks for blast furnace injection. During the first phase of this project a number of the objectives were realized, specifically: (1) a blast furnace sampling system was developed ...

Energy Technology Data Exchange (ETDEWEB)

With an objective to learn mechanisms in low-rank coal reformation processes, change of properties on coal surface was discussed. Difficulty in handling low-rank coal is attributed to large intrinsic water content. Since it contains highly volatile components, it has a danger of spontaneous ignition. The hot water drying (HWD) method was used for reformation. Coal which has been dry-pulverized to a grain size of 1 mm or smaller was mixed with water to make slurry, heated in an autoclave, cooled, filtered, and dried in vacuum. The HWD applied to Loy Yang and Yallourn coals resulted in rapid rise in pressure starting from about 250{degree}C. Water content (ANA value) absorbed into the coal has decreased largely, with the surface made hydrophobic effectively due to high temperature and pressure. Hydroxyl group and carbonyl group contents in the ...

Energy Technology Data Exchange (ETDEWEB)

The coal mining district in southeastern Santa Catarina State is considered one of the most polluted areas of Brazil. The author has identified significant preliminary results on the application of MSS-LANDSAT digital data to monitor the coal refuse areas and its environmental consequences in this region.

Science.gov (United States)

The overall objective of this project was to develop a new approach for the direct liquefaction of coal to produce an all-distillate product slate at a sizable cost reduction over current technology. The approach integrated coal selection, pretreatment, coal swelling with catalyst impregnation, liquefaction, product recovery with characterization, alternate bottoms processing, and a technical assessment including an economic evaluation. Heterofunctional solvents were the most effective in swelling coals. Also solvent blends such as isopropanol/water were more effective than pure solvents alone. Impregnating slurry catalysts simultaneously during coal swelling showed that better uptake was achieved with nonswelling solvent and higher impregnation temperature. Some enhancement in initial coal conversion was seen liquefying SO{sub 2}-treated Black Thunder ...

Science.gov (United States)

The objectives of this project are to support the DOE direct coal liquefaction process development program and to improve the useful application of analytical chemistry to direct coal liquefaction process development. Independent analyses by well-established methods will be obtained of samples produced in direct coal liquefaction processes under evaluation by DOE. Additionally, analytical instruments and techniques which are currently underutilized for the purpose of examining coal-derived samples will be evaluated. The data obtained from this study will be used to help guide current process development and to develop an improved data base on coal and coal liquids properties. A sample bank will be established and maintained for use in this project and will be available for use by other researchers. The reactivity of the non-distillable resids toward ...

Science.gov (United States)

A discussion covers the LOOP project to construct an offshore pipeline system, which will connect with onshore facilities at Fourchon, La., and two onshore pipelines (26 mi 48 in. Clovelly line and 53 mi 48 in. LOCAP line) connecting Fourchon with the existing Capline system at St. James, La.; the three-phase construction schedule, the first phase due to begin in the third quarter of 1978 with, e.g., onshore pipeline and salt dome storage facility construction which will yield an expected initial throughput of 1.4 million bbl/day; the marine terminal complex, consisting of control and pumping platforms, and three 7000 hp pumps to operate the system at 45,000-100,000 bbl/hr; the offshore lines, including lines between single-point mooring units and the pumping platform, the 21 mi 48 in. pipe to Fourchon, and corrosion protection of lines by an asphalt-sand mixture or a semiplasticized coal-tar enamel; the onshore system, including the Fourchon ...

Science.gov (United States)

This report presents the operating results for Run 243 at the Advanced Coal Liquefaction R and D Facility in Wilsonville, Alabama. This run was made in an Integrated Two-Stage Liquefaction (ITSL) mode using Illinois 6 coal from the Burning Star mine. The primary objective was to demonstrate the effect of a dissolver on the ITSL product slate, especially on the net C/sub 1/-C/sub 5/ gas production and hydrogen consumption. Run 243 began on 3 February 1983 and continued through 28 June 1983. During this period, 349.8 tons of coal was fed in 2947 hours of operation. Thirteen special product workup material balances were defined, and the results are presented herein. 29 figures, 19 tables.

Science.gov (United States)

The objective of this research was to convert coal into a soluble substance under mild conditions. The strategy involved two steps, first to breakdown the macromolecular network of coal, and second to add hydrogen catalytically. We investigated different basic reagents that could, in priciple, break down coal's structure and alkylation strategies that might enhance its solubility. We examined O- and C-alkylation, the importance of the strength of the base, the character of the added alkyl groups and other reaction parameters. This work provided new information concerning the way in which hydrogen bonding, polarization interactions between aromatic structures and covalent bonding could be disrupted and solubility enhanced. The objective of our research was to explore new organochromium chemistry that might be feasible for the hydrogenation of coal under mild conditions.

Energy Technology Data Exchange (ETDEWEB)

Double-crystal high-resolution X-ray fluorescence spectrometry was applied to the state analysis of sulfur in coal and related fly ash. For total sulfur, a proportional relationship exists between fluorescence intensities and the analytical values obtained by the oxygen-combustion method. Two oxidation states of sulfur were identified by a least square curve fitting method, by assuming that the spectrum profile is identical for each sulfur state but the intensity and the position are different. Sulfur in coal mainly consists of S/sup 2 -/, whereas that in coal fly ash mainly consists of S/sup 6 +/. As much as 0.04-0.08% of S/sup 2 -/ remains in fly ash.

British Library Electronic Table of Contents (United Kingdom)

Two plastic wastes (polyolefin-enriched and multicomponent), two lube oils (paraffinic and synthetic) and one coal-tar were assessed as individual and combined additives to coal blends for the production of blast furnace coke. The effects of adding 2wt.% of these additives or their mixtures (50:50 w/w) on the coking capacity of coal, coking pressure and coke quality parameters were investigated. It was found that the two plastic wastes reduce fluidity, whereas the addition of oils and tar helps to partially restore the fluidity of the coal-plastic blend. From the co-carbonization of the coking blend with the different wastes in a movable wall oven of over 15kg capacity, it was deduced that polyolefins have a detrimental effect on coking pressure. The addition of oils and tar to the coal-pl...

International Nuclear Information System (INIS)

This paper presents an assessment of recent improvements in the technology for direct coal liquefaction on the estimated commercial economics. The basis for the design and cost estimates is a series of studies sponsored by Amoco Corporation and Electric Power Research Institute, which were derived from the highly detailed Breckinridge Project, completed in the early 1980s under DOE sponsorship. The technology, design, and cost estimates reflect the current two-stage liquefaction technology practiced at the Advanced Coal Liquefaction Research facility in Wilsonville, Alabama. Details of the design bases and cost estimates and how they compare with the original Breckinridge study are described. Also examined are effects of feed coal rank, product slate, and the source of hydrogen (natural gas or coal) on the costs. Finally, the ways that projected future improvements in the technology will change the ...

Energy Technology Data Exchange (ETDEWEB)

Coal may be used to generate electrical energy by any of several processes, most of which involve combustion or gasification. Combustion in a coal-fired boiler and power generation using a steam-cycle is the conventional conversion method; however total energy conversion efficiencies for this type of process are only slightly over 30%. Integration of a gas-cycle in the process (combined cycle) may increase the total conversion efficiency to 40%. Conversion processes based on gasification offer efficiencies above 50%. H{sub 2}S is the predominant gaseous contaminant in raw coal gas. This process is concerned with the removal of H{sub 2} from coal gas through an electrochemical membrane technology.

Science.gov (United States)