International Nuclear Information System (INIS)

By means of an audio frequency plasma polymerisation ultra-thin gradient plasma polymer layers were deposited on zinc and zinc-coated iron. The aim was to generate an interfacial polymeric layer which bonds to an oxidised metal as well as to a subsequently applied organic coating and acts as an interfacial barrier layer for ions and water. Surface modifications were done in an in situ plasma cell with infrared reflection absorption spectroscopy (IRRAS). The zinc surface was first activated by an oxygen plasma to provide a freshly oxidised and contamination free oxide surface. The intermediate stages of the surface reactions could be revealed. Carbon dioxide molecules as oxidation products adsorbed on the growing zinc oxide and were desorbed at a later stage. An organosilicon plasma polymer was deposited directly on top of the oxide layer from a hexamethyldisilane (HMDS) plasma. Afterwards a cyclohexene ...

British Library Electronic Table of Contents (United Kingdom)

The thermal degradation and crystallisation behaviours of polyamide12/isotactic polypropylene (PA12/PP) blends were studied. Effects of blend ratio and compatibiliser concentration on the thermal degradation properties of the blends were analysed. The activation energy for degradation in compatibilised and uncompatibilised blends computed using Horowitz-Metzger equation was reported. The blend ratio as well as the presence of compatibiliser has significant effect on the thermal stability of the blends. Phase morphology was found to be one of the decisive factors that affected the thermal stability of both uncompatibilised and compatibilised blends. Melting and crystallisation behaviours of the blends in the presence and absence of compatibiliser were evaluated. It was observed that blendin...

Energy Technology Data Exchange (ETDEWEB)

This short paper (abstract) describes the characteristics and performances of prototypes of ultra-thin lithium micro-batteries (thickness < 0.2 mm) which can be incorporated into microelectronic circuits. (J.S.)

International Nuclear Information System (INIS)

The thermal properties of five types of radiation-induced wood-polymer composites based on a tropical hardwood, rubberwood (Hevea braziliensis), was studied by oxygen index measurement, differential thermal analysis (DTA) and thermogravimetry (TG). The DTA and TG curves of composites were different from those of rubberwood, which can be attributed to the presence of the incorporated polymers. Of the five composites, the one impregnated with bis(2-chloroethyl)vinyl phosphonate reduced the initial temperature of decomposition, increased the peak temperatures of exothermic reactions, and increased the char yield. Comparison with physical blends of rubberwood and the corresponding polymer provided some evidence of chemical interaction of wood and polymer in some of the composites. (author).

British Library Electronic Table of Contents (United Kingdom)

The mutual influence between the PP/PS polymer blend components during UV photodegradation was studied. Polypropylene (PP) and polystyrene (PS) have different photodegradation mechanisms, due to the larger UV absorption of polystyrene and formation of more stable tertiary carbon radicals. To compare the stabilities the kinetics of carbonyl formation was measured in different blend compositions. The results show that polystyrene presented a faster carbonyl formation than polypropylene, while the blends display faster kinetics than the isolated components. The kinetics of carbonyl formation of the blends was a function of polypropylene content. This result is unexpected if one considers the behaviour of each component alone. The kinetics and mechanism of UV degradation can be only explained ...

Energy Technology Data Exchange (ETDEWEB)

The physical properties of polymer blends consisting of one or more crystallizable components are affected by the microstructure of these materials. In particular, the degree of crystallinity can be influenced by processing parameters, and the crystallinity, as well as the phase distribution, may vary as a function of depth through an injection molded part Conventional x-ray diffraction techniques can provide information regarding both phase composition and degree of crystallinity, but, because of the relative transparency of these materials to wavelengths generally available in the laboratory, these techniques provide information representative of only the bulk. By employing parallel beam optics at varying grazing incidence angles, the x-ray sampling depth can be varied without loss of resolution. This technique can be used to vary the effective analysis depth from the top several hundred angstroms for low razing incidence to centimeters for ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Thermomechanical behavior of membranes based on blends of poly(vinyl alcohol) (PVA) with different weight percentage (wt %) of glycerol has been studied. Solid-state PVA/Glycerol polymer membranes were prepared by a solution casting method. The films were studied for thermal characteristics by differential scanning calorimetry (DSC) and thermogravimetric analysis and for the mechanical properties including hardness and modulus by nanoindentation method. The dispersion of glycerol within the polymer matrix was examined using scanning electron microscopy. Fourier transform infrared spectroscopy was used to confirm the formation of hydrogen bonding between the plasticizer and PVA in their blends and also to provide information on compatibility and physical interactions between the gl...

Wastenet

...of Mixing Sections 9 Interacting Rotor/Stator Mixers 10 Floating Ring Mixing Devices 11 Static (or Motionless) Mixers 12 Incorporation of Liquid Additives and Dispersions by Direct Addition 13 Dispersive Mixing of Fillers and Pigments 14 Dispersive Mixing Applied to Polymer Blending 15 Compounding with Single Screw Extruders Appendix - Preparation of Microtome Sections for Assessment of Dispersive In order to get a feel for this book, you can view Chapter 1 now, simply follow the link ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Melamine cyanurate (MCA) was utilized as an environmental friendly additive to prepare the nonhalogen flame retardant MCA/Nylon 66 composites by melt blending technique. Because of the strong hydrogen bond interactions and fine interfacial compatibility between MCA and Nylon 66, the resultant even dispersion of MCA filler in polymer matrix leads to the better toughness and strength of MCA/Nylon 66 composites than those of neat Nylon 66. Both Nylon 66 and MCA/Nylon 66 composites exhibit similar -crystalline structure, but the presence of MCA influences the distribution of 1 and 2 crystalline phases in Nylon 66 by inducing its hydrogen-bonded sheet separation. Moreover, the blending of MCA and Nylon 66 increases the crystallization temperature and exothermicity but decreases the the...

Energy Technology Data Exchange (ETDEWEB)

The effects of gate and drain bias stresses on thin film transistors fabricated in polysilicon films crystallized using the advanced sequential lateral solidification excimer laser annealing (SLS ELA) process, which yields very elongated polysilicon grains and allows the fabrication of TFTs without grain boundary barriers to current flow, are investigated as a function of the active layer thickness and of the TFT orientation relative to the grains. The application of hot carrier stress, with a condition of V{sub GS} = V{sub DS}/2, was determined to induce threshold voltage, subthreshold swing and transconductance degradation for TFTs in thicker polysilicon films and the associated stress-induced increase in the active layer trap density was evaluated. However, this device degradation was drastically reduced for TFTs fabricated in ultra-thin films. Furthermore, the application of the same stress condition to TFTs oriented vertically to the elongated grains resulted ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, the design of large thin PIN detector with a membrane stress avoidance configuration is proposed, and the related device fabrication process is developed. Ultra-thin PIN detector {approx} 1.13 cm{sup 2} in area is fabricated on a thin ( {approx} 35{mu}m) silicon membrane, and characterized. Detector performance improvement has been successfully demonstrated. With the membrane stress avoidance design, the improved detector exhibits a leakage of 6nA, which is at least 5 times lower than that of detector of identical junction area. The new detector features a full depleted capacitance of 110 pF, and a FWHM of 40.86 keV energy resolution for 5.486 MeV alpha particle spectrography.

Energy Technology Data Exchange (ETDEWEB)

We summarize recent developments in x-ray microscopy of polymers by focusing on the characterization of organic electronic devices. The quantitative compositions of model polymer blends have been mapped at a resolution of {approx}35 nm. Since it could be inferred that these devices have structures smaller than 35 nm, quantitative compositional mapping at length scales below the present resolution limit of x-ray microscopy is required. Organic devices thus serve to both highlight the success of NEXAFS microscopy to date, but to also outline the very real need for higher spatial resolution. New approaches to create improved optics or different acquisition modalities are required if x-ray microscopy is to make sustained contributions to such an important area of research as organic devices.

British Library Electronic Table of Contents (United Kingdom)

Abstract:- Significant interest has emerged in the introduction of food packaging materials manufactured from biodegradable polymers that have the potential to reduce the environmental impacts associated with conventional packaging materials. Current technologies in active packaging enable effective antimicrobial (AM) packaging films to be prepared from biodegradable materials that have been modified and/or blended with different compatible materials and/or plasticisers. A wide range of AM films prepared from modified biodegradable materials have the potential to be used for packaging of various food products. This review examines biodegradable polymers derived from polysaccharides and protein-based materials for their potential use in packaging systems designed for the protection of food ...

International Nuclear Information System (INIS)

This report summarizes the findings of a five-month LDRD project funded through Sandia's NTM Investment Area. The project was aimed at providing the foundation for the development of advanced functional materials through the application of ultrathin coatings of microporous or mesoporous materials onto the surface of substrates such as silicon wafers. Prior art teaches that layers of microporous materials such as zeolites may be applied as, e.g., sensor platforms or gas separation membranes. These layers, however, are typically several microns to several hundred microns thick. For many potential applications, vast improvements in the response of a device could be realized if the thickness of the porous layer were reduced to tens of nanometers. However, a basic understanding of how to synthesize or fabricate such ultra-thin layers is lacking. This report describes traditional and novel approaches to the growth of layers of microporous materials on silicon wafers. The ...

Energy Technology Data Exchange (ETDEWEB)

In this work, the silicon oxynitride layer was studied as a tunneling layer for non-volatile memory application by fabricating low temperature polysilicon thin film transistors on glass. Silicon wafers were oxynitrided by only nitrous oxide plasma under different radio frequency powers and plasma treatment times. Plasma oxynitridation was performed in RF plasma using inductively coupled plasma chemical vapor deposition. The X-ray energy dispersive spectroscopy was employed to analyze the atomic concentration ratio of nitrogen/oxygen in oxynitride layer. The oxynitrided layer formed under radio frequency power of 150 W and substrate temperature of 623 K was found to contain the atomic concentration ratio of nitrogen/oxygen as high as 1.57. The advantage of high nitrogen concentration in silicon oxide layer formed by using nitrous oxide plasma was investigated by capacitance-voltage measurement. The analysis of capacitance-voltage characteristics demonstrated that the ...

British Library Electronic Table of Contents (United Kingdom)

The use of Funtumia latex and nitrobenzene as molecular weight depressants for natural rubber was studied. Portions of a given sample of natural rubber latex were treated with these materials, and this provided a means of ascertaining the amount of Funtumia latex in a blend with natural rubber that could produce a lowering of the molecular weight equivalent to that from known concentrations of nitrobenzene in natural rubber latex. The molecular weight of the products decreased to an equilibrium value after 10 h of reaction with nitrobenzene. The calculations revealed that a 27.9% substitution of natural rubber latex (300 mL) with Funtumia rubber latex achieved the same result as nitrobenzene in the same polymer at concentrations of 0.5-2.0 wt % of the dry rubber content of the latex after ...

International Nuclear Information System (INIS)

The radiation induced reactions in LDPE in the presence of phenolic type antioxidants have been studied. It was shown that various antioxidants can influence the polyethylene network formation and the radical yield in different ways. The dependence of network structure on absorbed doses was determined by gel analysis, hot-set test and extraction of antioxidants for samples irradiated with accelerated electrons. It was found that the antioxidants eluted from polyethylene in higher percentage influence polymer crosslinking to a smaller degree. The ESR studies of #gamma#-irradiated blends of polyethylene with antioxidant indicate the presence of alkyl and phenoxyl radicals. The role of antioxidant molecules on radiation induced reactions in polyethylene-antioxidant systems is considered. The correlation between the network structure and the type of additive in polyethylene is also discussed. (author).

Energy Technology Data Exchange (ETDEWEB)

There is growing interest in using {sup 242m}Am as a nuclear fuel for space reactors and nuclear batteries. In this paper, we discuss different {sup 242m}Am enrichments, as well as fuel weight requirements, to produce a critical reactor. It was found that relatively low enrichments of {sup 242m}Am, about 10 w/o, are enough to guarantee criticality. Such low enrichments might eliminate the need for a {sup 242m}Am enrichment process. It was also found that the best results for low {sup 242m}Am requirements are obtained with a moderator to fuel volume ratio of 10,000.

KoreaScience (Korea)

Full Text Available

International Science & Technology Center (ISTC)

Shungit Filled Polymers for Artificial Bone Articulations

Energy Technology Data Exchange (ETDEWEB)

The conductive ultra thin films were fabricated from mixed monolayers containing stearic acid and Head-to-Tail poly(3-alkylthiophene). These films exhibited well-defined layered structures as determined by optical absorption and X-ray diffraction measurements. The UV-Vis absorption spectra of these films showed lower energy absorption shifts of 48 nm from that of the random poly(3-alkylthiophene)/stearic acid LB films. The blue shift of absorption maximum of the LB film is attributed to the increase of {pi}-conjugation length caused by no steric hindrance of alkyl side chains. The conductivity of the Head-to-Tail poly(3-hexylthiophene)/stearic acid LB films was greatly improved in the range of 67-100 S/cm. (orig.)

International Nuclear Information System (INIS)

There is growing interest in the use of natural fibres as the reinforcements for polymer composites in the automotive industry and as matrix for composites in building products application to replace synthetic fibres. In this respect the aim of this study is to develop an environmental friendly composites for furniture industry based on EFB fibres and sago starch. In this preliminary study, a basic composition and processing of EFB fibres-sago starch composites were established and the properties of the composites were determined. EFB fibre content was varied between 50-80% by weight. The amount of sago starch in liquid form was also varied and final weight percentage of sago starch added into the EFB fibres was adjusted accordingly. The mixtures of EFB fibres and sago starch were blended using Haake Rheomixer. The preliminary results indicate that the impact and flexural strengths increased up to 33.58 J/m"2 and 18.92 Mpa, respectively at 70% ...

Energy Technology Data Exchange (ETDEWEB)

Short communication.

J-STORE (Japan)

Full Text Available

Science.gov (United States)

Blast furnace coke containing low grade coal in a high blending ratio is manufactured by a method which comprises blending not less than 60% of a blended coal having an adjusted total moisture content of not more than 4% with not more than 40% of briquettes and carbonizing the resultant mixture. The blended coal consists essentially of not less than 80% of coking coal and not more than 20% of low grade coal. When coking coal of a kind which has its coking property segregated according to its grain size distribution is pulverized and classified by sifting and the portion of fine particles is used as mixed with the coking coal, the blending ratio of the low grade coal in the blended coal can be increased to up to 35%. The briquettes consist essentially of not less than 10% of coking coal and not more than 90% of low grade coal.

Science.gov (United States)

... IDA DOCUMENT D- 1174 THE DARPA HIGH-PERFORMANCE POLYMER PROGRAM ... The DARPA High-Performance Polymer Program, Volume I: ...

Energy Technology Data Exchange (ETDEWEB)

An investigation of the effect of blending of two different coals in various ratios on the hydrogenation reaction was carried out using a red mud-sulphur catalyst. Three Japanese coals and an Australian brown coal were used in the study. The conversion of the blended coals was compared with that obtained with each of the coals alone. A blend of the Yallourn brown coal and Shin-Yubari coal showed a synergism: it is considered that hydroaromatics from the Japanese coal promote the hydrogenation of the Yallourn coal. (The tables and captions in this paper are in English).

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Not Available

J-STORE (Japan)

Full Text Available

International Nuclear Information System (INIS)

This paper deals with preparation of PE clay nano composite specimen for transmission electron microscopy (TEM) and studying the difference between dispersion of clay in low density polyethylene using poly(hydrogen methyl siloxane) (PHMS) as coupling agent and untreated one. Argon ion milling is the conventional means by which film sections are thinned to electron transparency for TEM analysis, but this technique exhibits significant problems. In particular, selective thinning and imaging of sub-micrometer inclusions during sample milling are highly problematic. We have achieved successful results using the focused ion beam (FIB) lift-out technique, which utilizes a 30 kV Ga"+ ion beam to extract electron transparent specimens with nanometer scale precision. Using this procedure, we have prepared a number of thin film materials representing a range of structures and compositions for TEM analysis. We believe that FIB milling will create major new opportunities in the field of thin film ...

Energy Technology Data Exchange (ETDEWEB)

The relationship between microstructure and macro properties of different cementitious materials has been investigated. This study consists of the following tasks: using NMR and IR to better characterize the amorphous and poorly crystalline phases that occur in blended cements; characterizing the microstructure of the hydration products of modified Portland cement as a function of different percentages of pozzolan replacements by ESEM, SEM, and EDS; comparing the properties of blended cement pastes with a control group of normal Portland cements; and studying the engineering aspects of blended cement that are important for identifying and characterizing fundamental phenomena that are responsible for their durability. The overall influence of the nanoscale and microscale structure of blended and Portland cement on the properties of the resultant composite will be discussed.

British Library Electronic Table of Contents (United Kingdom)

High molecular weight samples of the novel biodegradable polyester poly(ethylene sebacate) (PESeb) were synthesized. Miscible poly(ethylene sebacate)/poly(4-vinyl phenol) semicrystalline/amorphous blends were prepared by applying the solvent casting method. Miscibility was proved by the single composition dependent glass transition temperature over the entire composition range observed in DSC traces of the quenched blend samples and also by the melting point depression. The Flory-Huggins interaction parameter was found to be x12 = -1.3. Also, FTIR spectra supported the hypothesis of intermolecular interactions due to hydrogen bonding. The crystallization of PESeb in blends was studied. As expected, isothermal crystallization rates decreased in the blends with increasing the PVPh content. T...

Energy Technology Data Exchange (ETDEWEB)

Amphiphilic block copolymers are synthesized by sulfonation of poly(styrene-b-methyl methacrylate) (PS-b-PMMA) using acetyl sulfate, and are blended with poly(vinylidene fluoride) (PVDF) to prepare a new proton exchange membrane, in which PMMA is miscible with PVDF. The morphology and the transport properties of the membranes are investigated as functions of the degree of sulfonation as well as the blend ratio. Notable transition of phase-separated morphology is observed as the PVDF content of the blend is increased. Both the proton conductivity and the ion-exchange capacity (IEC) of the membrane increase with increasing the degree of sulfonation of PS-b-PMMA, and they are also enhanced as the phase-separated domains of blend membrane are well-ordered. Unlike the Nafion membrane, the proton conductivity of the blend membrane increases up to 90 C, indicating the ...

Energy Technology Data Exchange (ETDEWEB)

Wood/polymer composites (WPC) have been prepared from pinewood with different compounds using gamma irradiation: butyl acrylate, butyl methacrylate, styrene, acrylamide, acrylonitrile, and unsaturated polyester styrene resin. The polymer loading was determined with respect to the compound concentration and the irradiation dose. The polymer loading increases generally with increase in the monomer or polymer concentration. Tensile and compression strength have been improved in the four cases, but no improvement was observed using unsaturated polyester styrene resin or acrylamide.

DEFF Research Database (Denmark)

The thermodynamic framework that was developed in a previous work [Vrachnos et al. Ind. Eng. Chem. Res. 2004, 43, 2798] for the description of chemical and vapor-liquid equilibria of carbon dioxide, hydrogen sulfide, and their mixtures in aqueous methyldiethanolamine (MDEA) solutions is revised and extended in this study to the absorption of carbon dioxide into aqueous monoethanolamine (MEA) solutions and aqueous MDEA-MEA blends. The results of the model are compared with experimental data taken from the literature. Very satisfactory predictions of acidic gas vapor-liquid equilibrium over MDEA, MEA, and their blends at various concentrations, acidic gas loadings, and temperatures are obtained.

British Library Electronic Table of Contents (United Kingdom)

To reduce the cost of the formed coke briquettes which can be used as a substitute fuel to the metallurgical coke for the blast furnace from the coke breeze alternative binders and their blends were used. The high temperature behavior was investigated. The binders tested were: the nitrogen blown, air blown coal tar pitch and the blend of air blown coal tar pitch with the phenolic resins blends. The phenolic resin blends were prepared by mixing equal amount of resole and novalac. From the results, nitrogen blowing resulted in the weakest briquettes. The air blowing procedure should be preferred in place of nitrogen blowing for this purpose. When the air blown coal tar pitch was used alone as a binder, the briquettes must be cured at 200^oC for 2h, then carbonized at a temperature above 670^...

International Nuclear Information System (INIS)

A method is described for immobilizing or solidifying waste material, which includes blending the waste material with powdered metal and subjecting the mixture of waste material and powdered metal to high pressure. (author).

Science.gov (United States)

... Title : Flame Retardant Effects in PVC-Epoxidised Natural Rubber Miscible Blends: Halogen and Non-Halogen Based Additives,. Corporate Author : ...

Energy Technology Data Exchange (ETDEWEB)

Vegetable oils such as soybean oil will be converted to novel polymers using hydroformylation and other catalytic processes. These polymers can be used in the construction, automotive, packaging, and electronic sectors.

Science.gov (United States)

... The addition of 0.5 pphr of fine thermal carbon black to the polymers gave good resistance to 500 hours of ultraviolet (UV) xposure in a Weather ...

Energy Technology Data Exchange (ETDEWEB)

Surface analytical studies of high nitrogen austenitic stainless steels exposed to deaerated 0.1M HCl have revealed that nitrogen alloying additions influence the composition of salt layers and the passive film/alloy interface. In this study the authors employ electrochemical techniques and variable angle X-ray Photoelectron Spectroscopy (XPS) to examine the passive films formed on a series of austenitic stainless steels, Fe18Cr8Ni, Fe18Cr8Ni0.2N, Fe20Cr20Ni, Fe20Cr20Ni6Mo and Fe20Cr20Ni6Mo0.2N, in acidic chloride aqueous solution. In addition, several other model alloys, Fe19Cr, Fe19Cr9Ni, Fe19Cr2.5Mo, and Fe19Cr9Ni2.5Mo, were examined before and after electrochemical surface nitriding, a technique proven to have an effect analogous to N alloying. It was shown that nitrogen, nickel and molybdenum additions independently and in certain combinations stimulate selective dissolution of iron, resulting in a significant enrichment of chromium beneath the passive film. In most cases, the ...

Energy Technology Data Exchange (ETDEWEB)

Coal solids (SRC) and distillate oils are combined to afford single-phase blends of residual oils which have utility as fuel oils substitutes. The components are combined on the basis of their respective polarities, that is, on the basis of their heteroatom content, to assure complete solubilization of SRC. The resulting composition is a fuel oil blend which retains its stability and homogeneity over the long term.

Energy Technology Data Exchange (ETDEWEB)

An evaluation of eastern shale oil (ESO) residue as an asphalt additive to reduce oxidative age hardening and moisture susceptibility was conducted by Western Research Institute (WRI). The ESO residue, have a viscosity of 23.9 Pa{lg_bullet}s at 60{degree}C (140{degree}F), was blended with three different petroleum-derived asphalts, ASD-1, AAK-1, and AAM-1, which are known to be very susceptible to oxidative aging. Rheological and infrared analyses of the unaged and aged asphalts and the blends were then conducted to evaluate oxidative age hardening. In addition, the petroleum-derived asphalts and the blends were coated onto three different aggregates, Lithonia granite (RA), a low-absorption limestone (RD), and a siliceous Gulf Coast gravel (RL), and compacted into briquettes. Successive freeze-thaw cycling was then conducted to evaluate the moisture susceptibility of the prepared briquettes. The rheological analyses of the ...

Energy Technology Data Exchange (ETDEWEB)

In this study, the exhaust gas from a common-rail direct injection diesel engine was investigated both upstream and downstream warm-up catalytic converters (WCC). Three different types of ultra-low sulfur fuels (ethanol-diesel blend, ethanol-diesel blend with cetane improver and pure diesel) were tested in this study. The objective of the work was to study the engine performance and the formation of THC (total hydro carbon), CO (carbon monoxide), NO{sub x} (nitrogen oxides), smoke and PM (particulate matters) when using these fuels. THC and CO emissions of the ethanol-diesel blend fuels were slightly increased, and about 50-80% mean conversion efficiencies of THC and CO on catalysts were achieved in the ECE R49 13-mode cycle. Smoke was decreased by more than 42% in the entire ECE 13-mode cycles. From the measurement of scanning mobility particle sizer (SMPS) for the particle size range of 10-385 nm, the total number and ...

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

The effect of the moisture content in amorphous polymers (PS, PVC, PMMA) on their electro-physical properties is considered. Analytical relationships describing the inflence of the external-field frequency and environmental relative humidity on the conductivity of the polymers are given. For the use of these polymers as active elements of moisture sensors, the moisture-resistive effect is estimated.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

A wood-polymer composite has been produced by impregnating the wood with the monomer and subsequently polymerizing it by exposure to a gamma radiation source. To compare the improvement in creep deformation of the wood due to the polymer impregnation, a nonlinear Norton-Bailey isothermal mathematical function has been used to model the bending creep deformation of the wood-polymer composites. Results show that the impregnation significantly improves the creep resistance of the wood. The maximum creep resistance is obtained when the amount of polymer impregnation exceeds about 30%. An interfacial interaction between the wood cell wall and the polymer could explain the creep deformation improvement, as well as the maximum impregnation level beyond which little improvement occurs. The results indicate that polymer impregnation is a viable method for improving the ...

International Nuclear Information System (INIS)

Polymerizing effects of high energy radiation has been found suitable for preparation of wood-polymer composites. In the present work after evaluating polymer products that have been obtained by irradiation method, wood-polymer composites have been prepared by in situ polymerization of vinyl acetate, acrylic acid and acrylic acid/styrene mixture using two samples of Iranian hardwoods, Beech and Hornbeam. These woods and their composites have been tested for their physical and mechanical properties. The results have shown that chemical bonding between polymer and the cell wall component lead to better strength properties in the composites. (author).

International Nuclear Information System (INIS)

A wood/polymer composite was produced by impregnating Ramin wood with methyl methacrylate monomer and subsequently polymerizing it by gamma irradiation. To assess the improvement in compression strength of the wood caused by the polymer impregnation, a microbuckling compression failure mechanism was used to model the compression failure of the composite. Such a mechanism was found to predict a linear relationship between the compression strength and the percentage polymer impregnation (by weight). Uniaxial compression test results at 45(#+-#5)% and 90(#+-#5)% relative humidity levels, after being statistically analysed, showed that such a linear relationship was valid for up to 100% polymer impregnation. (author).

British Library Electronic Table of Contents (United Kingdom)

Two plastic wastes (polyolefin-enriched and multicomponent), two lube oils (paraffinic and synthetic) and one coal-tar were assessed as individual and combined additives to coal blends for the production of blast furnace coke. The effects of adding 2wt.% of these additives or their mixtures (50:50 w/w) on the coking capacity of coal, coking pressure and coke quality parameters were investigated. It was found that the two plastic wastes reduce fluidity, whereas the addition of oils and tar helps to partially restore the fluidity of the coal-plastic blend. From the co-carbonization of the coking blend with the different wastes in a movable wall oven of over 15kg capacity, it was deduced that polyolefins have a detrimental effect on coking pressure. The addition of oils and tar to the coal-pl...

International Nuclear Information System (INIS)

Wood-polymer composites (WPC) have been prepared of pinewood with different monomers using Gamma radiation: acrylamide, butyl acrylate, butyl methacrylate, styrene, acrylonitrile, and polyester. The polymer loading was determined as a function of monomer concentration and absorbed dose. The data show that polymer loading increases by increasing the monomer concentration. In two cases, BMA and polyester, the polymer loading decreases at high concentrations. This can be explained by the increase of the viscosity. Thus the diffusion of the compound into bulk would be slower. The absorbed dose seems to play a positive role in enhancing the polymer loading by increasing the dose. The mechanical properties, tensile and compression strength, have been improved in the most cases for all monomer concentrations or absorbed doses. Using polyester there was no improvement in the mechanical ...

International Nuclear Information System (INIS)

Ultrathin solid polymer electrolyte membranes containing sulfonic ester groups were prepared by polymerization of methyl benzenesulfonate and octamethylcyclotetrasiloxane in a glow discharge plasma. The sulfonic ester groups of the plasma polymer were transformed to lithium sulfonate groups by treatment with lithium iodide. Hybridization of this plasma polymer containing the lithium sulfonate groups with poly(ethylene oxide) (average Mw 300) resulted in the formation of a single lithium ion conductive film. The hybrid polymer electrolyte films were about 1 #mu#m thick, pinhole-free, adherent to various substrates, and showed ionic conductivities at 60 degrees C of the order of 10"- "6 S cm"- "1 (10"2 #OMEGA# cm"2 resistance per unit area of as-prepared solid polymer electrolyte). This material shows promise for electrochemical applications such as all solid-state lithium batteries, ...

Energy Technology Data Exchange (ETDEWEB)

The effect of irradiation on the tensile properties of oil palm empty fruit bunch (OPEFB) fiber reinforced poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends were studied. The composites were prepared by mixing the fiber and the PVC/ENR blend using HAAKE Rheomixer at 150 deg. C. The composites were then irradiated by using a 3.0 MeV electron beam machine at doses ranging from 0 to 100 kGy in air and room temperature. The tensile strength, Young's modulus, elongation at break and gel fraction of the composites were measured. Comparative studies were also made by using poly(methyl acrylate) grafted OPEFB fiber in the similar blend system. An increase in tensile strength, Young's modulus and gel fraction, with a concurrent reduction in the elongation at break (Eb) of the PVC/ENR/OPEFB composites were observed upon electron beam irradiation. Studies revealed that grafting of the OPEFB fiber with ...

Energy Technology Data Exchange (ETDEWEB)

This book contains papers relating to the 1990 Future Transportation Technology Conference and Exposition. Included are the following papers; Examination of rich mixtures operation of a dual fuel engine, A hybrid natural gas vehicles, Performance analysis of a spark ignited engine with ETBE as a blending agent.

Energy Technology Data Exchange (ETDEWEB)

Methods were studied for using sugar as a feed additive for converting the sodium-bearing wastes stored at the Idaho Chemical Processing Plant into granular, free flowing solids by fluidized-bed calcination at 500{degrees}C. All methods studied blended sodium-bearing wastes with Fluorinel wastes but differed in the types of sugar (sucrose or dextrose) that were added to the blend. The most promising sugar additive was determined to be sucrose, since it is converted more completely to inorganic carbon than is dextrose. The effect of the feed aluminum-to-alkali metal mole ratio on calcination of these blends with sugar was also investigated. Increasing the aluminum-to-alkali metal ratio from 0.6 to 1.0 decreased the calcine product-to-fines ratio from 3.0 to 1.0 and the attrition index from 80 to 15%. Further increasing the ratio to 1.25 had no effect.

Energy Technology Data Exchange (ETDEWEB)

Methylmethacrylate polymerisation in the presence of 4 wt% butadiene-acrylonitrile rubber was carried out at fixed dose-rate and temperature. The effect of irradiation was investigated with respect to the mechanical and dynamic-mechanical properties in the solid state. A general increase of the 'compatibilisation' on irradiation is obtained. In fact both rubber and polymethylmethacrylate glass transition temperatures, determined through dynamic-mechanical analysis, reveal the presence of strong interactions between the components. Furthermore an improvement of the mechanical tensile properties of the blends is observed when irradiation is continued after polymerisation, at least until a certain absorbed dose.

Energy Technology Data Exchange (ETDEWEB)

Fatty acids such as stearic acid (SA), palmitic acid (PA), myristic acid (MA), and lauric acid (LA) are promising phase change materials (PCMs) for latent heat thermal energy storage (LHTES) applications, but high cost is the most drawback which limits the utility area of them in thermal energy storage. The use of fatty acids as form-stable PCM will increase their feasibilities in practical LHTES applications due to reduced cost of the energy storage system. In this regard, a series of fatty acid/poly(methyl methacrylate) (PMMA) blends, SA/PMMA, PA/PMMA, MA/PMMA, and LA/PMMA were prepared as new kinds of form-stable PCMs by encapsulation of fatty acids into PMMA which acts as supporting material. The blends were prepared at different mass fractions of fatty acids (50, 60, 70, 80, and 90% w/w) to reach maximum encapsulation ratio. All blends were subjected to leakage test by heating the blends over the ...

UK PubMed Central (United Kingdom)

The main aim of the present study was to evaluate potential of ternary complexation (comprising of drug, cyclodextrin and polymer) as an approach for taste masking. For this purpose famotidine with...Full Text Available

UK PubMed Central (United Kingdom)

A variety of albumin polymers were prepared and tested for binding with hepatitis B surface antigen (HBsAg): synthetic polymers cross-linked by either glutaraldehyde or carbodiimide; heat-aggregated...Full Text Available

Science.gov (United States)

The present article studies the electret state of polymers when moving through an alternating-current corona discharge plasma and investigates means for the determination of the transition of the polymeric material from the initial state of the electret when the corona-displaying voltage is increased.

Science.gov (United States)

... spatially defined fashion. Many surface modification techniques require a sequential chemical treatment of the surface.6 ...

International Nuclear Information System (INIS)

English 2006 2 p. Brazil Rocha, RM Centro Tecnico Aeroespacial, Sao

Medline Plus

... ever get in this slide. This is basically mechanical properties of the polyuretha urethane polymer called Bioflex versus ...

Science.gov (United States)

... Accession Number : ADA546034. Title : Fluoroalkyl Polyhedral Oligomeric Silsesquioxane (F-POSS) Based Monomers and Polymers. ...

International Nuclear Information System (INIS)

The compressive and bending strengths of a local tropical wood (Kapur-Dryobalanop sp.) were improved significantly by suitable impregnation of polymeric monomers (methylmethacrylate, methylmethacrylate - 5% dioxane and vinyl acetate) into the wood cellular structure and subsequent irradiation to form a wood-polymer composite. Statistical analysis revealed a linear relationship between increase in the strengths and the percentage of polymer impregnated. Fractographic analysis of the impact fractured surfaces under the scanning electron microscope showed the nature of the wood-polymer interface, which could account for the increase in the compressive and bending strengths. (author).

Science.gov (United States)

... Descriptors : *Combustible cartridge cases, *Polymers, *Test equipment, *Patents, Combustion chambers, Breech mechanisms, Gas generating ...

Science.gov (United States)

FEP polyethylene mechanical properties affected by UV. " Siloxane-modified materials resist AO. " Nonsilicone polymers attacked by AO ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents ionic conductivity results obtained with polymer electrolytes and also with propylene carbonate solutions. The domain of electrochemical activity of this salt has been determined using cycle volt-amperometry in propylene carbonate. Preliminary experiments on the stability of the polymer electrolyte with respect to the lithium electrode have been carried out for a possible subsequent use in lithium batteries. (J.S.) 4 refs.

Energy Technology Data Exchange (ETDEWEB)

Interpenetrated lattices (IPL) are combinations of reticulated polymers linked together by permanent crisscross. This structure is well-adapted to combined highly incompatible pairs of polymers. The in-situ sequential method has been applied successfully to the synthesis of ethylene poly-oxides / poly-siloxanes IPLs. The results concerning the preparation of such lattices and their behaviour as solid polymer electrolytes are presented in this paper. (J.S.) 24 refs.

Energy Technology Data Exchange (ETDEWEB)

The dual characteristics in the performance of polymers in wood-polymer composites systems have been pursued with regard to the resolution of mechanical anisotropy of wood and the improvement in dimensional stability. The objective of the present study is to pursue the polymerization mechanism in wood under electron beam irradiation and the temperature dependence of polymer-wood interactions induced at various levels of higher order structure of wood in order to understand the polymer performance. Veneers used in the study were of rotary-cut beech (Fagus crenata Blume) 0.65 mm thick. All samples were oven-dried in vacuo at 80/sup 0/C for 30 hr. The monomers used in the study were methyl methacrylate, styrene, acrylic acid, acrylonitrile, and unsaturated polyester. Experimental details are given. Results are given and discussed.

Energy Technology Data Exchange (ETDEWEB)

Wood polymer composite (WPC) specimens were produced by impregnating a tropical wood with methyl methacrylate and subsequently polymerised by ..gamma..-irradiation. Beam specimens of varying weight percentages of polymer were then subjected to a three point bend creep test under a constant load condition, for 250, 300 and 350 N. A Norton-Bailey (power law) mathematical model was used to describe the creep behavior, with the creep components determined by a nonlinear regression analysis. Significant creep improvements were obtained from the composite specimens as compared to the untreated wood specimens. Results indicated that maximum creep resistance is obtained when the amount of polymer loading exceeded 30%. An interfacial interaction between the polymer and the wood cell wall was used to account for the behavior of the increase in the creep resistance.

Energy Technology Data Exchange (ETDEWEB)

Polymers containing hydroquinone, catechol or their corresponding benzoquinones are a special class of redox polymers. Three pathways of their syntheses are possible: condensation polymerization of suitable monomers, addition polymerization of vinyl monomers containing redox moiety, and chemical attachment of redox unit onto pre-made polymeric matrix. A range of functionalized matrices have been employed such as polyethers, polyesters, polycarbonates, polyurethanes, polyamides and others. Protection of their phenolic functionality has conducted to chemically interesting redox polymer precursors. The presence of a redox moiety coupled with the extant functionalization of the polymer matrix makes the materials very valuable, of wide properties and consequently of vast applicability. For instance, in the oil field, some polymers such as carboxy-methyl-cellulose (CMC) are often applied ...

International Nuclear Information System (INIS)

Complimentary spectroscopic, microscopic and electrochemical studies were performed to characterise the barrier properties as well as the interface structure of model iron substrates covered with thin plasma polymer films. Cathodic plasma polymers were deposited which show high barrier properties. The metal surface was pre-treated by a reducing or oxidising plasma. This allowed the adjustment of the oxidation state of the interface layer. The interface structure was characterised by means of X-ray photoelectron sputter profiles, infrared spectroscopy and the application of a Kelvin probe. The investigations show that the measured Voltapotential on the plasma polymer surface can be correlated with the oxidation state of the interface. Reducing plasmas lead to an almost oxide free surface. After deposition of the plasma polymer, this reduced state of the oxide is sensitive to re-oxidation of the interface ...

Energy Technology Data Exchange (ETDEWEB)

The use of vegetable oils as a fuel in diesel engines causes some problems due to their high viscosity compared with conventional diesel fuel. Various techniques and methods are used to solve the problems resulting from high viscosity. One of these techniques is fuel blending. In this study, a blend of 50% sesame oil and 50% diesel fuel was used as an alternative fuel in a direct injection diesel engine. Engine performance and exhaust emissions were investigated and compared with the ordinary diesel fuel in a diesel engine. The experimental results show that the engine power and torque of the mixture of sesame oil-diesel fuel are close to the values obtained from diesel fuel and the amounts of exhaust emissions are lower than those of diesel fuel. Hence, it is seen that blend of sesame oil and diesel fuel can be used as an alternative fuel successfully in a diesel engine without any modification and also it is an ...

Energy Technology Data Exchange (ETDEWEB)

An evaluation of eastern shale oil (ESO) residue as an asphalt additive to reduce oxidative age-hardening and moisture susceptibility was conducted. The ESO residue, having a viscosity of 23.9 Pa{sm_bullet}s at 60{degrees}C (140{degrees}F), was blended with three different petroleum-derived asphalts, AAD-1, AAK-1, and AAM-1, that are known to be very susceptible to oxidative aging. Rheological and infrared analyses of the unaged and aged asphalts and the blends were then conducted to evaluate oxidative age-hardening. In addition, the petroleum-derived asphalts and the blends were coated onto three different aggregates, Lithonia granite (RA), a low-absorption limestone (RD), and a silicious Gulf Coast gravel (RL), and compacted into briquets. Successive freeze-thaw cycling was then conducted to evaluate the moisture susceptibility of the prepared briquets. The abbreviations used above for the asphalts and the aggregates are ...

Energy Technology Data Exchange (ETDEWEB)

Biodiesel is an alternative fuel for internal combustion engines. It can reduce carbon monoxide (CO), hydrocarbon (HC) and particulate matter (PM) emissions, compared with diesel fuel, but there is also an increase in nitrogen oxides (NOx) emission. This study is aimed to compare the effect of applying a biodiesel with either 10% blended methanol or 10% fumigation methanol. The biodiesel used in this study was converted from waste cooking oil. Experiments were performed on a 4-cylinder naturally aspirated direct injection diesel engine operating at a constant speed of 1800 rev/min with five different engine loads. The results indicate a reduction of CO{sub 2}, NOx, and particulate mass emissions and a reduction in mean particle diameter, in both cases, compared with diesel fuel. It is of interest to compare the two modes of fueling with methanol in combination with biodiesel. For the blended mode, there is a slightly higher brake thermal ...

British Library Electronic Table of Contents (United Kingdom)

In this article, we describe a method used to prepare an in situ sodium-activated, organomodified bentonite clay/styrene-butadiene rubber nanocomposite master batch via a latex blending technique. The clay master batch was used for compound formulation. Octadecyl amine was used as an organic intercalate. The clay was purchased from local suppliers and was very cheap. Sodium chloride was used for in situ activation of the clay. The wide-angle X-ray diffraction data indicated that the in situ sodium activation helped to increase the intergallery distance from 1.28 to 1.88 nm. A transmission electron micrograph indicated intercalation and partial exfoliation. The thermal properties were relatively better in the case of the sodium-activated, organomodified bentonite-clay-containing compound. A...

British Library Electronic Table of Contents (United Kingdom)

Abstract A series of polypropylene carbonate (PPC)/ZnO nanocomposite films with different ZnO contents were prepared via a solution blending method. The morphological structures, thermal properties, oxygen permeability, water sorption, and antibacterial properties of the films were investigated as a function of ZnO concentration. While all of the composite films with less than 5 wt % ZnO exhibited good dispersion of ZnO in the PPC matrix, FTIR and SEM results revealed that solution blending did not lead to a strong interaction between PPC and unmodified ZnO. As such, poor dispersion was induced in the composite films with a high ZnO content. By incorporating inorganic ZnO filler nanoparticles, the diffusion coefficient, water uptake in equilibrium, and oxygen permeability decreased as the ...

British Library Electronic Table of Contents (United Kingdom)

The flame retardancy of polybutylene terephthalate (PBT) was studied focusing on the effect of various oxides. Thermo-gravimetric analysis, pyrolysis/gas chromatography/mass spectrometry, and elemental analysis (EA) were used to analyze the flame retardancy, which were observed through the UL-test and a cone calorimeter. Many oxides influenced the flame retardancy and some of them could suppress the flammability of PBT. In particular, the blended-PBTs with ZnO and V2O5 accelerated the degradation and the edges of oxygen consumption were shorter than neat-PBT although the flammability became poorer. The quantitative analysis of the scission products and the results of EA showed that hydrolysis, successive dehydration, and other various reactions changed the scission route to generate less f...

British Library Electronic Table of Contents (United Kingdom)

In this study, the effect of intake charge dilution with carbon dioxide on the combustion and emission characteristics of a 4-cylinder direct-injection diesel engine fueled with biodiesel, ethanol-biodiesel and methanol-biodiesel were investigated. With increase of intake CO"2 concentration, CO, HC, particulate mass concentration, particle number concentration and geometric diameter (GMD) of all fuels increased while NO"x decreased obviously. After addition of methanol and ethanol in biodiesel, the NO"x, particulate mass concentration and particle number concentration decreased at each intake CO"2 concentration, compared with biodiesel. Moreover, as the intake CO"2 concentration increased from 2% to 5.6%, particulate mass concentration of the alcohol-biodiesel blends remained almost unchan...

Energy Technology Data Exchange (ETDEWEB)

Although magnesium is not attacked by hydrocarbons, it reacts vigorously with anhydrous methanol, raising concerns about the compatibility of the metal with methanol blend fuels. This paper describes the behavior of magnesium alloys in laboratory tests in static contact with methanol-containing fuels at 110/sup 0/F. Water in small concentrations (above 0.25% by weight of the methanol content) is shown to prevent the destructive attack of magnesium by these fuels. The required water content is well within the water tolerance of methanol-GTBA (gasoline grade tertiary-butyl alcohol) cosolvent fuel blends. Die cast AZ91HP shows greater resistance to methanol reaction than does AZ31B sheet.

British Library Electronic Table of Contents (United Kingdom)

The effect of various diallyl (diallyl ortho phthalate, diallyl terephthalate and diethylene glycol diallyl carbonate) and triallyl monomers (triallyl cyanurate and triallyl isocyanurate) on the processability of polyphenylene oxide (PPO) was studied. The solubility parameters of the monomers indicated that diallyl orthophalate, dially terephthalate and triallyl cyanurate should be miscible with PPO suggesting their applicability as reactive plasticizers to improve the processability of PPO. Rheological studies of 60:40 wt:wt PPO:allylic blends indicate that the addition of 40wt% of allylic monomers significantly improved processability - blends of 60PPO:40DEGDAC indicates the highest viscosity and the highest T"g. Rheological studies and dynamic mechanical analysis on various PPO/DAOP ble...

Energy Technology Data Exchange (ETDEWEB)

Industrial applications of thermoplastic polymers are often limited by their poor adhesion properties. In this work the effect of surface oxyfluorination on the adhesion properties was investigated for polyethylene (PE), polyoxymethylene (POM), polybutylene terephthalate (PBT) and polyamide 6 (PA6). The adhesive joint strength was quantified using lap-shear tests. These results were correlated with the changes in the chemical composition of the surface, determined by X-ray photoelectron spectroscopy (XPS), in the surface free energy, measured by the contact angle method, and in the topography, using white-light confocal microscopy. The adhesive strength is strongly improved for all four polymers, but the degree of this increase depends on the polymer type. The surface free energy shows a similar trend for all four polymers. A high surface free energy exceeding 50 mN/m was observed after ...

Energy Technology Data Exchange (ETDEWEB)

This invention pertains to passivation-free solid-state rechargeable batteries composed of Li.sub.4 Ti.sub.5 O.sub.12 anode, a solid polymer electrolyte and a high voltage cathode. The solid polymer electrolyte comprises a polymer host, such as polyacrylonitrile, poly(vinyl chloride), poly(vinyl sulfone), and poly(vinylidene fluoride), plasticized by a solution of a Li salt in an organic solvent. The high voltage cathode includes LiMn.sub.2 O.sub.4, LiCoO.sub.2, LiNiO.sub.2 and LiV.sub.2 O.sub.5 and their derivatives.

Energy Technology Data Exchange (ETDEWEB)

Researchers are developing polymer-based coating systems to reduce scaling and corrosion of air-cooled condensers that use a geothermal fluid spray for heat transfer augmentation. These coating systems act as barriers to corrosion to protect aluminum fins and steel tubing; they are formulated to resist the strong attachment of scale. Field tests have been done to determine the corrosion and scaling issues related to brine spraying and a promising organometallic polymer has been evaluated in salt spray tests.

Energy Technology Data Exchange (ETDEWEB)

Fractal dimensional analysis was employed to obtain a quantitative measure of the morphology of polymer networks formed by UV irradiation induced polymerization of photo-reactive mesogenic monomers dissolved in a liquid crystal host medium. The fractal dimensions obtained, may be interpreted by polymer network growth following a percolation-like model for monomer concentrations well below the solubility limit. On passing the solubility limit, the polymerization process changes from a (radical chain) solution polymerization to a dispersion polymerization, with fractal dimensions decreasing and suggesting a cluster-cluster aggregation process for monomer concentrations above the solubility limit, similar to the aggregation of colloidal particles.

International Nuclear Information System (INIS)

The effect of additives on the grafting of a monomer, butylmethacrylate (BA), into simul (a soft wood) has been studied using "6"0Co source at 3 Mrad. The enhancement of polymer loading (grafting) by the addition of minute amounts (1%) of oligomers and of polyfunctional monomers into simul + BA system has been further increased in the presence of acid and urea. The synergistic polymer loading yields by acid addition cause substantial decrease of tensile strength values of wood-plastic composite; but urea increases both polymer loading and tensile strength values synergistically in these systems. (author).

UK PubMed Central (United Kingdom)

Axon outgrowth and guidance to the proper target requires the coordination of filamentous (F)-actin and microtubules (MTs), the dynamic cytoskeletal polymers that promote shape change and locomotion....Full Text Available

UK PubMed Central (United Kingdom)

The rejection thresholds of Phormia regina Meigen for twenty-four glycols have been determined. A definite relationship between the concentration of the test material and the distribution...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The research carried out in Canada in the design of containers for the disposal of radioactive waste has focussed on spent nuclear fuel, even though the quantities of other currently stored radioactive wastes are substantially greater. Research carried out at the Royal Military College of Canada on the effects of mixed fields of radiation on high polymer adhesives and composite materials has shown that some polymers are quite resistant to radiation and could well serve in the fabrication of radioactive waste disposal containers. The purpose of this research was to determine if thermoplastic polymers could be used as superior materials to replace metals in the application of low and intermediate level radioactive waste disposal containers. Polymers have the advantage that they do not corrode like metals. The experimental methods, used in this research, focused on the effects of radiation on the ...

Energy Technology Data Exchange (ETDEWEB)

The use of solvating polymers of polyether type is an interesting solution for the manufacturing of high capacity lithium batteries with lithium metal anodes and which can operate at T > 50 deg. C. These operating conditions are perfectly compatible with electric-powered vehicle and stationary battery applications. In order to improve the ionic conductivity of polymer electrolytes, new aprotic and amorphous polyether lattices have been synthesized having a good conductivity but also good thermal, mechanical and electrochemical stabilities. Two type of 3-D polyether lattices obtained by reticulation of linear pre-polymers have been selected as host polymers: unsaturated poly-condensate and unsaturated co-polyethers. (J.S.) 18 refs.

Energy Technology Data Exchange (ETDEWEB)

A polymer-based additive that permanently reduces hardness in wood electrical transmission poles treated with a chromated copper arsenate (CCA) preservative, has been developed by a team of IREQ researchers. A three-phase project is being funded by Hydro-Quebec to evaluate the additive's effect on full-size hydro poles subjected to actual climatic conditions. The evaluation project is designed to test the CCA and the additive's degree of retention by analyzing the hardness measurements against climbing tests, and the washing resistance of the chromium, copper and arsenate in the CCA/polymer-additive treatment. CCA-treated poles will be used for reference. Accelerated aging tests to characterize the polymer's resistance to UV rays will also be part of the validation program.

Energy Technology Data Exchange (ETDEWEB)

The development of 'Green Chemistry' requires new materials to replace the conventional organic chemistry by biological catalysts, to produce fine chemicals in an environmentally friendly manner. Microbial whole cells can be directly used as biocatalysts, providing a simple and cheap methodology since enzyme isolation and purification are avoided. High-density polyethylene (HDPE) is a very stable polymer though it can be activated by gamma radiation to induce grafting. Glycidyl methacrylate was grafted onto macroporous HDPE and PP in the range of 1-6%, proportional to the initial monomer concentration. Grafted polymers were further chemically modified with ethylenediamine to generate a cationic hydrogel of micron-size thickness onto the internal polymer surfaces. Modified polymers were able to immobilize Gram-positive and Gram-negative bacteria that can catalyze a chemical reaction as ...

British Library Electronic Table of Contents (United Kingdom)

The formation of nanoparticles during the radiation-induced chemical reduction of silver ions, copper ions, and nickel ions in films based on poly(acrylic acid)-poly(ethylenimine) complexes are studied via electron microscopy. This approach allows preparation of composites containing nanoparticles that are randomly distributed in the polymer matrix and materials with a regular spatial distribution of nanoparticles across the film thickness and in subsurface layers. The structure of metal-polymer hybrid materials is dependent on the irradiation conditions, the type of reduced metal ions, and their initial content in polymer matrices. The ratio between the rate of nucleation and the rate of growth of nanoparticles in the matrices of interpolyelectrolyte complexes depends on the intensity of ...

International Nuclear Information System (INIS)

Portuguese 1998 p. 47 Brazil Silva, Edemilson P. Universidade Federal,

Energy Technology Data Exchange (ETDEWEB)

Solar cells consisting of polymer layers sandwiched between a transparent electrode on glass and a metal top electrode are studied using dynamic time-of-flight secondary ion mass spectrometry (TOF-SIMS) in dual-beam mode. Because depth profiling of polymers and polymer-metal stacks is a relatively new field the craters were thoroughly investigated by environmental SEM (ESEM), interferometry, surface profilometry and tapping mode AFM. A huge increase in crater bottom roughness was observed when starting from the aluminum top layer going in depth, resulting in a loss of depth resolution. It is shown that layer-to-layer diffusion and contaminants at buried interfaces can be extracted from the depth profiles when taking into account the loss of depth resolution.

UK PubMed Central (United Kingdom)

The use of 2-pyridinealdoxime (paoH)/N,N′-donor ligand (L-L) “blend” in cobalt chemistry has afforded two cationic mononuclear cobalt(III) complexes of the general type [Co(pao)₂(L-L)]⁺,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A detailed definitive cost estimate is given for an ethanol/gasohol storage and blending terminal serving a planned distillery at a Louisiana sugar factory. Included are an analysis of the accuracy of the estimate, labor rates efficiency, materials and labor escalation, as well as detailed calculations for each account of the project. (LEW)

Energy Technology Data Exchange (ETDEWEB)

An evaluation of eastern shale oil (ESO) residue as an asphalt additive to reduce oxidative age-hardening and moisture susceptibility was conducted. Rheological and infrared analyses of the unaged and aged asphalts and blends were then conducted to evaluate oxidative age-hardening. 18 refs., 5 figs., 6 tabs.

International Nuclear Information System (INIS)

Although some polymer conductors of electricity (ex. Polyanilines) are materials known for more than 100 years, only recently have the interesting chemical, electrical and optic properties of their insulating and conducting forms been recognized. Advances made in the chemistry of polymer conductors have also led to improvements in processing them. This work studies a practical application of these materials: the use of polymer conductors for the remote welding of insulating thermoplastic polymers, using energy from microwaves for the local heating of the union. Many thermoplastics (for ex. Polyethylene) do not absorb, or absorb very little, energy from microwaves. Different conductor materials (conductor polymers, carbon nanotubes), however, heavily absorb energy from microwaves with the resulting heating. In this way the welding zone can be heated without affecting the rest of the ...

International Nuclear Information System (INIS)

In earlier works, the inelastic mean free path (IMFP) of electrons was determined by elastic peak electron spectroscopy (EPES) using Ni and Ag reference standard samples, but fully neglecting surface excitation. Surface excitation that is characterized by the surface excitation parameter (SEP), and may affect considerably the elastic peak for the sample and the reference material. The SEP parameters of selected conducting polymers (polythiophenes, polyaniline and polyethylene) were determined by EPES using Si and Ge reference samples. Experiments were made with a hemispherical analyzer of energy resolution 100-200 meV in the E = 0.2-2.0 keV energy range. The composition of the sample surfaces was determined by in situ XPS, their surface roughness by AFM. The experimental SEP parameter data of eight polymer samples were determined by our new procedure, using the formulae of Chen and Werner et al. in the E = 0.2-2.0 keV energy range. The trial ...

Energy Technology Data Exchange (ETDEWEB)

The use of WPC as an important insulating material is studied by determining its dielectric constant. The variation of dielectric constant with moisture content is also investigated. Preliminary results show that all untreated woods studied have a higher dielectric constant than their polymer composites with the exception of Kapur and Keruing. It is therefore postulated that the presence of polymers has led to a decrease in the number of polarizable units. Such a material may be useful commercially.

International Nuclear Information System (INIS)

The feasibility of using a thermoplastic-powder metallurgy technique for the fabrication of porous niobium rods was investigated. Some early problems were overcome to successfully extrude the polymer coated niobium powder into long lengths. The effects of certain process variables were investigated. Residual porosity and extrusion pressure were found to be regulated by the polymer fraction. The procedures for taking the extruded polystyrene--niobium rods through the heat treatments to the final, tin infiltrated stage are explained.

International Nuclear Information System (INIS)

Radiation processed wood-polymer composites (WPC) can replace conventional wood in many industrial applications. However, for proper utilization of the composites, adequate testing and evaluation programmes are essential. The paper briefly describes the development of WPC at the Bhabha Atomic Research Centre, Bombay, and the evaluation of WPC for various applications in greater details. The various mechanical properties and their significance in overall performance of WPC are also discussed. (author).

Energy Technology Data Exchange (ETDEWEB)

A membrane process utilizing dialysis and selective complexation by water-soluble polymers has been developed. This process, termed affinity dialysis, has been shown to be selectively extract and concentrate both cations and anions in a manner similar to ion exchange or solvent extraction. The selective removal of calcium from sodium with selectivity of about 30, removal of chromate ion from dilute streams, and separation of transition metal ions such as Cu/Fe and Cu/Zn have all been successfully demonstrated. Effects of different polymers, polymer concentration, temperature, and flow rates have been studied. The effect of increased polymer concentration is to increase product concentration if appropriate changes in feed, polymer solution, and strip flow rates are made. A continuous polymer solution recycle and regeneration system has been constructed and ...

Energy Technology Data Exchange (ETDEWEB)

Nanoimprinting is a fast-growing technique for nanoscale patterning. One of the remaining issues in nanoimprinting is the removal of the residual layer after nanoimprinting. Traditionally the residual layer is removed by an oxygen reactive-ion etching (RIE) step. The need for a vacuum environment and dedicated equipment in this step lowers the throughput and increases the cost of the nanoimprinting process. It also prevents the possibility of patterning isolated functional polymers because oxygen RIE destroys the functional materials. In this work, novel nanoimprinting schemes are developed to nondestructively remove the residual layer in thermal nanoimprinting by solvent developing and dewetting. Combined with a transfer-bonding technique, three-dimensional polymer scaffolds are achieved. The techniques developed here eliminate the RIE step in thermal nanoimprinting and are compatible with roller nanoimprinting for large-scale patterning of ...

Energy Technology Data Exchange (ETDEWEB)

The adverse effect of moisture diffusion on the properties of wood has been one of the main weaknesses of wood. Using a gamma irradiation method, wood-polymer composites have been produced which exhibit significant improvement in mechanical properties like compression, creep deformation and creep rupture particularly at high humidity. It has been thought that the impregnation of polymer into the wood has affected the moisture diffusion in the wood, so that its adverse effects on the mechanical properties has been reduced. In this report the apparent diffusion coefficients of a Ramin wood impregnated with varying amounts of polymethyl methacrylate (PMMA) were determined using a Fick's law approach. An initial linear relationship was found for impregnation of up to 70% PMMA, after which the diffusion coefficient levels off to a maximum value, for the three environmental relative humidity levels of 40, 60 and 90({plus minus}5)%. The ...

Science.gov (United States)

The kinetics of electrical breakdown of thin (15-70 ?m) layers of polymers and ceramics in a constant-sign field at 77-480 K has been investigated. The temperature dependences of the longevity (breakdown waiting time) of both dielectrics have been found to be similar to each other. At elevated temperatures, the longevity of the dielectrics varies exponentially with increasing temperature, and at reduced temperatures, it is temperature-independent (there is an athermal plateau). The mechanisms of elementary events controlling the process of preparation of the dielectrics for breakdown at elevated and reduced temperatures are the thermal-fluctuation over-barrier electron transition from trap to trap and the tunneling (under-barrier) transition, respectively. The hopping electron transport in the field direction gives rise to critical space charges causing breakdown of the dielectrics. The transition barrier heights (trap depths) have been determined. The ...

Science.gov (United States)

We study the emission zone in a single-layer polymer light-emitting diode. The emission zone is found by studying the angular distribution of the electroluminescence. The emission is modeled by accounting for optical interference. We account for birefringence of the anode layer in our model. The active polymer was, however, found to be isotropic. The anode consists of a single-layer of the conducting polymer complex poly(3,4-ethylenedioxythiophene) and poly(styrene sulfonate) (PEDOT-PSS), with enhanced conductivity. As a cathode we use plain aluminum. By using only PEDOT-PSS we avoid having a thin metal layer or indium-tin-oxide as the anode in the path of the escaping light. The active material is a substituted polythiophene with excellent film forming properties. A comparison between the experimental and calculated angular distribution of light emission from a single-layered polymer light-emitting ...

Energy Technology Data Exchange (ETDEWEB)

This paper explores for the first time the post-radiation-induced-graft polymerization on solid substrate using reversible addition-fragmentation transfer (RAFT) mechanism. Radiation-induced graft polymerization onto polymers is a potentially interesting technique to create easily new materials from highly resistant polymers, e.g. surface graft polymerization of acrylic acid (AA) onto poly(vinylidene difluoride) (PVDF) improves its surface properties without losing its excellent mechanical properties. As a consequence of the radical nature of the polymerization processes it is difficult to control molecular weight of grafted chains, and therefore design and standardize the properties of the final product. RAFT polymerization is a suitable method to obtain monodisperse polymers. The ability of the RAFT agents to control the polymer chain length could be an interesting approach to improve the grafted ...

Science.gov (United States)

Before electroless plating, polymer surfaces must be sensitized and/or activated by using either the conventional two-step or one-step process. The latter stage is a compulsory one to make such surfaces catalytic, e.g., for Ni-P deposition. These processes are performed here using O{sub 2}, NH{sub 3}, or N{sub 2} plasma pretreatments. Reaction mechanisms are proposed for each of the processes and for each type of surface considered (oxygenated or both oxygenated and nitrogenated by the plasma treatment). Direct palladium chemisorption onto nitrogenated groups is highlighted. This allows one to simplify the process making the surface catalytic via elimination of the use of SnCl{sub 2} and to extend the method to any polymer. An additional interest of the plasma treatments, besides their high efficiency in grafting chemical functions, is to perform this grafting at will on selected areas which results in selective metallization.

British Library Electronic Table of Contents (United Kingdom)

Nanocapsules coated by medicinal plants have many applications in drug manufacturing. Medicinal plants can be loaded on nanocapsules with polyesteric triblock copolymer poly ethylene glycol-poly butylene adipate-poly ethylene glycol (PEG-PBA-PEG) as shell and olive oil can be introduced as a core of nanocapsules by a method known as polymer deposition solvent evaporation method. In this research, first, certain amount of polymer, Matricaria recutita extract and olive oil were mixed with acetone and then, water was added to the solution using magnetic stirrer. After which the acetone was removed by vacuuming and finally nanocapsules were found by freezing-drier. The study showed the size of nanocapsules depends on variety of factors such as the ratio of polymer to oil and concentration of p...

CERN Document Server

We discuss theoretically and numerically the intramolecular form factor $F(q)$ in dense polymer systems. Following Flory's ideality hypothesis, chains in the melt adopt Gaussian configurations and their form factor is supposed to be given by Debye's formula. At striking variance to this, we obtain noticeable (up to 20%) non-monotonic deviations which can be traced back to the incompressibility of dense polymer solutions beyond a local scale. The Kratky plot ($q^2F(q)$ {\\it vs.} wavevector $q$) does not exhibit the plateau expected for Gaussian chains in the intermediate $q$-range. One rather finds a significant decrease according to the correction $\\delta(F^{-1}(q)) = q^3/32\\rho$ that only depends on the concentration $\\rho$ of the solution, but neither on the persistence length or the interaction strength.

Science.gov (United States)

A sulfonated fluoroalkyl graft polymer (FGP) membrane was prepared as a polymer electrolyte. First, the FGP membrane was grafted with styrene under UV irradiation. The grafted FGP was then sulfonated to functionalize it for proton conductivity. The grafting degree of the membrane increased with increasing grafting time during UV irradiation. The proton conductivity of the membrane increased with increasing grafting degree. The swelling ratio was independent of the grafting time, however, the water uptake increased with increasing grafting degree. Based on these results, it was found that the UV-initiated styrene grafting occurred along the membrane thickness direction. Moreover, the membrane was embedded within the glass fibers of the composite. This composite electrolytic membrane had 1.15 times the proton conductivity of a Nafion 117 membrane.

Energy Technology Data Exchange (ETDEWEB)

The performance of different polymers used to flocculate red mud particulate materials in the Bayer process can be evaluated on the basis of their efficiency to achieve adequate settling velocities and turbidity levels. In this study, three commercially available flocculants are evaluated under typical conditions found in the last washer of a Bayer plant. The different shear levels are produced by using a modified Couette flow system. Great differences are noticed in the performance of the polymers when they are compared at different dosages and at different shear rate levels. The data collected also suggests that conventional cylinder settling tests may not be adequate to measure the performance of certain types of polymers. (author)

International Nuclear Information System (INIS)

Some results and experimental procedures of laboratory are reported in the frame of researches conducted for the development of new nanostructured composite materials. These new materials, which are constituted by an organic phase: the polymer and an inorganic phase: the silicate, are being strongly investigated nowadays so it is expected that they could provide, among other, better electrical insulation properties and flame-delay in electrical and electronic applications. The laboratory experimental work has been developed from two families of polymers, thermoplastics and thermosets and clays silicates providing lamellar type. There are now some preliminary results, such as obtaining thin films of these nanocomposite materials, their complete characterization by X-ray diffraction, scanning microscopy and thermogravimetric analysis, they do well to wait for future research activities. (author)

Energy Technology Data Exchange (ETDEWEB)

New technologies are needed to reduce the current high rate of well abandonment. Improved sweep efficiency, reservoir conformance, and permeability modification can have a significant impact on oil recovery processes. Microorganisms can be used to selectively plug high-permeability zones to improve sweep efficiency and impart conformance control. Studies of a promising microbial system for polymer production were conducted to evaluate reservoir conditions in which this system would be effective. Factors which can affect microbial growth and polymer production include salinity, pH, temperature, divalent ions, presence of residual oil, and rock matrix. Flask tests and coreflooding experiments were conducted to optimize and evaluate the effectiveness of this system. Nuclear magnetic resonance imaging (NMRI) was used to visualize microbial polymer production in porous media. Changes in fluid distribution within the pore system ...

CERN Document Server

The emergence of nanoscience has increased the importance of experiments able to probe the very local structure of materials, especially for disordered and heterogeneous systems. This is technologically important; for example, the nanoscale structure of glassy polymers has a direct correlation with their macroscopic physical properties. We have discovered how a local, high frequency dynamic process can be used to monitor and even predict macroscopic behavior in glassy polymers. Polyvinylethylenes vitrified by different chemical and thermodynamic pathways exhibit different densities in the glassy state. We find that the rate and amplitude of a high frequency relaxation mode (the Johari-Goldstein process involving local motion of segments of the chain backbone) can either correlate or anti-correlate with the density. This implies that neither the unoccupied (free) volume nor the configurational entropy governs the local dynamics in any general ...

Energy Technology Data Exchange (ETDEWEB)

In a recent publication [I. Galanakis, K. Ozdog-tilde an, E. Sasiog-tilde lu, B. Aktas, Phys. Rev. B 74 (2006) 140408(R)] we have shown that in the case of CrAs and related transition-metal chalcogenides and pnictides, crystallizing in the zinc-blende structure, the excess of the transition-metal atoms leads to half-metallic ferrimagnetism. The latter property is crucial for spintronic applications with respect to ferromagnets due to the lower stray fields created by these materials. We extend this study to cover the case where the transition-metal atoms sitting at antisites are not identical to the ones in the perfect sites. In Cr-based compounds, the creation of Mn antisites keeps the half-metallic ferrimagnetic character produced also by the Cr antisites. In the case of VAs, Cr and Mn antisites keep the half-metallic character of VAs (contrary to V antisites) due to the larger exchange splitting exhibited by these atoms.

Energy Technology Data Exchange (ETDEWEB)

This presentation explored the use of marine biodiesel in the Puget Sound region. Marine vessels are now adopting biodiesel fuels as a means of expressing corporate commitments to reducing greenhouse gas (GHG) emissions and the environmental impacts of hydrocarbons released into marine environments. Various biodiesel blends have been designed for use in small commercial, recreational, and research vessels. Biodiesel has also been adopted by charter and whale watching vessels in the Puget Sound. The Guemes Island Ferry has recently been re-configured to use biodiesel fuels, with 2 fuel tanks capable of receiving 2200 gallons at a time. The ferry adopted biodiesel after receiving soot complaints from marinas, and hopes to serve as a model for other vessels in the region. Four fueling docks supply the biodiesel blend to marine vessels. The sale of biodiesel has doubled in some marinas over the last 5 years. Deterrents to biodiesel use include ...

Energy Technology Data Exchange (ETDEWEB)

The main objectives of Phase 2 are to determine the feasibility of using cements with controlled particle size distributions (CPSD cements) in practical concrete applications, and to refine our estimates of the potential energy savings that may ensue from such use. The work in Phase 2 is divided into two main tasks, some parts of which will be carried out simultaneously: Task 1 will continue cement paste studies to optimize cement performance similar to those of Phase 1, but with particular emphasis on gypsum requirements, blended cements, and water-reducing admixtures. This task will also include preparation of sufficient CPSD cements for use in all Phase 2 work. Task 2 will be a comprehensive examination of the properties of concretes made with CPSD cements. This will include optimization of concrete mix designs to obtain the best possible performance for practical applications of both portland and blended cements. The effects of chemical ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Grazing incidence X-ray diffraction (GI-XRD) is used to characterize the crystallographic dynamics of low molecular weight (LMW) and high molecular weight (HMW) poly(3-hexylselenophene) (P3HS) films and blend films of P3HS with [6-6-]-phenyl-C61-butyric acid methyl ester (PCBM) as a function of -step-by-step- thermal annealing, from room temperature to 250-C. The temperature-dependent GIXRD data show how the melting point of P3HS crystallites is decreased by the presence of PCBM. P3HS crystallite domain sizes dramatically increase upon annealing to the P3HS melting temperature. The formation of well-oriented HMW P3HS crystallites with the (100) plane parallel to the substrate (edge-on orientation), when cooled from melt, are observed. We compare the behaviour of P3HS pure and blen...

British Library Electronic Table of Contents (United Kingdom)

Summary Reactive extrusion was utilised for starch/poly(butylene adipate co-terephthalate) (PBAT) blown film production, using maleic anhydride (MA) and citric acid (CA), alone or combined, as compatibilisers. These compounds (2% w/w) were added to the starch/PBAT (55:45) mixture after dispersion on glycerol. More rigid films, with greater tensile strength (9.82--0.45-MPa), were produced when 2.0% CA was used. The opposite, little homogeneity and poor tensile strength (0.77--0.12-MPa) and elongation (2.67--0.67%) were found in films produced using 2.0% MA. Barrier properties to water vapour were improved by compatibilisers. FTIR analysis showed that CA and MA were able to promote esterification/transesterification reactions. Blends containing CA also showed better phase compatibilisation i...

Energy Technology Data Exchange (ETDEWEB)

The objective of this task was to obtain powder property data on candidate glass former materials, sufficient to guide conceptual design and estimate the cost of glass former handling facilities as requested under Part B1 of BNFL Technical and Development Support. Twenty-nine glass forming materials were selected and obtained from vendors for the characterization of their physical properties, durability in caustic solution, and powder flow characteristics. A glass former was selected based on the characterization for each of the ten oxide classes required for Envelope A, B, and C mixtures. Three blends (A, B, and C) were prepared based on formulations provided by Vitreous State Laboratory and evaluated with the same methods employed for the glass formers. The properties obtained are presented in a series of attached Tables. It was determined that five of the ten glass formers, (kyanite, iron oxide, titania, zircon, and zinc oxide) have the potential to cause some ...

Energy Technology Data Exchange (ETDEWEB)

Electric utilities are actively seeking ways of optimizing the economics of their operations by improving productivity and reducing time and money spent on maintenance. Iberdrola, a Spanish utility, is using advanced machine condition-monitoring technology to centralize control and maintenance of its hydropower projects as a means of achieving those goals. The company is using a blend of technologies to supervise their projects from a regional control center. The monitoring scheme makes use of data from on-line, machine-condition monitors, displays from in-plant audio asnd video equipment, and analysis from the control center`s SCADA system.

International Nuclear Information System (INIS)

The principle of conservation and transferability of chemical bonds explains the recent discovery by extended x-ray absorption fine-structure measurements of two unequal anion-cation bond lengths R/sub A/C and R/sub B/C in A/sub x/B/sub 1-x/C zinc-blende semiconductor alloys despite the close adherence of the lattice constant to the average value (Vegard rule). This bond alternation, manifested as a structural distortion to a local chalcopyrite coordination around the anions, explains also most of the observed optical bowing in semiconductor alloys.

Energy Technology Data Exchange (ETDEWEB)

A local Heine-Abarenkov model potential is proposed for zinc blende-type crystals. The potential parameters are determined by satisfying the zero pressure condition and the first zero of the empirical pseudopotential interpolated from band calculations. Two sets of parameters are presented for thirteen tetrahedral compounds such as AlP, AlAs, AlSb, GaP, GaAs, GaSb, InP, InAs, InSb, ZnS, ZnSe, ZnTe, and CdTe.

Science.gov (United States)

Coke petrography could be useful for improving blast furnace coke properties and for solving cokemaking production problems. To do this, quantitative correlations between coke structure, coal properties and carbonization conditions, and coke properties are useful, if not essential. Some examples of correlations of this type were presented in this paper. Specifically, microstructural parameters of cokes produced in Inland Steel Company's pilot scale coke oven were correlated with the rank and blend proportions of the parent coal, with the reactivity of the coke, and with the ASTM stability of cokes prepared from single coals.

International Nuclear Information System (INIS)

The existence of characteristic longitudinal optical and transverse optical phonons of cubic ZnO in ZnO nano-tetrapods is determined by Raman spectroscopy and first-principles calculations. Stacking sequence change at the boundary of the core and legs is also identified by high-resolution transmission electron microscopy. Based on this experimental and theoretical evidence, we demonstrate that the lattice structure of ZnO nano-tetrapods is hierarchical with a zinc blende core connecting to four wurtzite legs. Furthermore, we establish the atomic configuration and propose a formation mechanism induced by Laplace pressure in the initial growth stage of ZnO nano-tetrapods.

International Nuclear Information System (INIS)

Biodegradable and green plastics are the new tendency in the world. The effect of the electron beam irradiation in aromatic aliphatic copolyester and the blend with corn starch films (Ecoflex"R and Ecobras"R) were studied by tensile strength at break, elongation at break, Scanning Electronic Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FT-IR), Differential Scanning Calorimetry (DSC), crosslinking degree and biodegradability. The measurements in both, the machine direction and the transverse direction were made for mechanical tests. It was found that, the electron irradiation caused an increase in the strength at break of the blend with corn starch film, when doses of up to 10 kGy were applied. A significant decrease of the elongation at break of the blend with corn starch was observed at doses of 10 kGy and 40 kGy. It was not found important change in tensile properties for aromatic aliphatic copolyester. ...

UK PubMed Central (United Kingdom)

A stiff skin forms on surface areas of a flat polydimethylsiloxane (PDMS) upon exposure to focused ion beam (FIB) leading to ordered surface wrinkles. By controlling the FIB fluence and area of exposure...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

The electric explosion of a conductor being part of an electric cable is studied. It is ascertained that the electric properties of a polymeric dielectric depend nonlinearly on the maintenance of the ultradisperse metal filler. In the course of the numerous heating-cooling processes of an insulator, a streamlining of the structure of a polymeric composite occurs.

Energy Technology Data Exchange (ETDEWEB)

Using a series of polycations synthesized by atom transfer radical polymerization (ATRP), we investigate the effects of the polymer charge density and hydrophobicity on salt-induced interdiffusion of polymer layers within polyelectrolyte multilayer (PEM) films. Polycations with two distinct hydrophobicities and various quaternization degrees (QPDMA and QPDEA) were derived from parent polymers of matched molecular weights poly(2-(dimethylamino)ethyl methacrylate) (PDMA) and poly(2-(diethylamino)ethyl methacrylate) (PDEA) by quaternization with either methyl or ethyl sulfate. Multilayers of these polycations with polystyrene sulfonate (PSS) were assembled in low-salt conditions, and annealed in NaCl solutions to induce layer intermixing. As revealed by neutron reflectometry (NR), polycations with lower charge density resulted in a faster decay of film structure with distance from the substrate. Interestingly, when comparing ...

Energy Technology Data Exchange (ETDEWEB)

Polymers are required to use in radiation environments as insulation materials. However, they often suffer from tracking failure. There is an increasing demand to evaluate radiation effects on dielectric performance. This paper presents a recurrence plot (RP) approach to analyse surface discharge sequences of gamma-ray irradiated polymer materials based on tracking test. Studying the non-linear characteristics of discharge sequences can assist in understanding the underlying mechanism of the discharge process. Discharge sequences of the test are extended to m-dimensional phase space by using the phase space reconstructed method. As test samples, polybutylene terephthalate (PBT) and polybutylene naphthalate (PBN) were irradiated to 100 kGy and then up to 1 MGy with a dosage rate of 10 kGy h{sup -1} by using a {sup 60}Co gamma source. The tracking tests were carried out according to the test method described in IEC60112. It is found that the RPs ...

UK PubMed Central (United Kingdom)

Dimethacrylate polymers and composites are seeing increased usage in orthopedics. As these applications require the material to integrate with the surrounding tissues, direct contact cytotoxicity...Full Text Available

Science.gov (United States)

... Highly-Functional Materials" was launched in JFY1996 under the New Materials field. This project was ... Bio-mimetic materials" (1) Advanced stimuli responsive materials (2) Harmonized molecular materials ...

UK PubMed Central (United Kingdom)

Synthetic polypeptide antigens of L amino acids, although bearing repeating sequences, are thymus-dependent (L-TD), whereas the same polymers composed of D amino acids are thymus-independent (D-TI),...Full Text Available

International Nuclear Information System (INIS)

In the synthesis of the peptidyl-polymer corresponding to the sequence (57-100) of the #beta# chain of human hemoglobin on Teflon with radiationally grafted polystyrene a comparative study was made of different methods of fragment condensation. It was shown that the most effective methods are azide condensation and condensation with the use of complex F.

Science.gov (United States)

Measurements of PEM fuel cell device performance were made with different gas inlet temperatures and relative humidity using a newly-designed test fixture. Significant improvement in device performance was observed when the fuel inlet temperature was increased above the operating temperature of the cell. These measurements were then correlated to a model to describe energy and mass transport processes. Proton exchange membrane (PEM), fuel cells--the focus of this study--use an ion conducting polymer, especially polyperfluorosulfonic acid materials. These polymer materials, when imbibed with water, exhibit solution-like properties, but because the anions are chemically bound to the polymeric structure, the electrolyte is contained. Importantly, product water removal is simplified, as electrolyte dilution is not a concern. However, the proton transport rate is a function of the polymer geometry, which is set, in part, by the ...

Science.gov (United States)

... of new construction materials; and the behavior of infrastructure materials and structural ... polymers, reinforcing materials, wood and biodegradable structural materials; scale effects from ...

Science.gov (United States)

international vehicles, control centers, and ground support personnel. ... consists of thin membranes made from a polymer-based film and ..... (including airplanes and submarines), environmental monitoring, and control ...... sciences can use it to analyze the birth and death of stars, the formation of solar ...

International Nuclear Information System (INIS)

This is a preliminary study on the sound absorption properties of two tropical hardwoods, Light Red Meranti and Ramin, and their wood-polymer composites. Sound absorption is measured using a standing wave apparatus. The samples are of one thickness (7 mm) and cut longitudinally. Wood-polymer composites are made by impregnating the samples with methyl methacrylate which is polymerized in situ through #gamma#-irradiation. Both woods and their composites are better sound absorbers at higher sound frequencies. With partial impregnation, the absorption coefficients are improved upon particularly in the region between 1-3 kHz. (author).

Energy Technology Data Exchange (ETDEWEB)

The resistance of six tropical hardwoods to fungal degradation by two wild-type strains of Phanerochaete chrysosporium Burdsall was investigated using vermiculite burial and wood-block weight loss techniques. Radiation-induced wood-polymer composites (WPC), based on two hardwoods Ramin and Rubberwood with methyl methacrylate, were prepared, and samples were also exposed to the wood-rotting fungus. A significant improvement in resistance to fungal decay was observed in the WPC. Scanning-electron micrographs of the two woods and their composites after fungal degradation are presented and discussed.

International Nuclear Information System (INIS)

Radiation-initiated polymerization of styrene and acrylic acid in poplar wood were investigated for the preparation of wood-polymer composites. The direct irradiation method was applied to the monomer adsorbed poplar wood specimens. 8000 Ci "6"0Co source at a dose rate of about 0.4 Mrad/h was used. Furthermore the effects of carbon tetrachloride, methanol, dioxane and acrylonitrile on styrene polymerization were investigated and the reaction rates were calculated for each case. The influence of CCl_4 (10%) on acrylic acid polymerization in poplar wood was also determined. (author).

Science.gov (United States)

The removal of Reactive Black 5 dye in an aqueous solution by electrocoagulation (EC) as well as addition of flocculant was investigated. The effect of operational parameters, i.e. current density, treatment time, solution conductivity and polymer dosage, was investigated. Two models, namely the artificial neural network (ANN) and the response surface method (RSM), were used to model the effect of independent variables on percentage of dye removal. The findings of this work showed that current density, treatment time and dosage of polymer had the most significant effect on percentage of dye removal (p0.8). PMID:21411950

British Library Electronic Table of Contents (United Kingdom)

Purpose - This paper aims to describe the technology and applications of nanocomposite materials. Design/methodology/approach - This paper discusses products, applications and technological developments in polymer, ceramic and metal nanocomposites. It concludes with a brief consideration of electronic component applications. Findings - It is shown that polymer nanocomposites and the materials used in their production are commercially available and finding applications in several industries, including automotive, military, food, electronics and leisure, due to their enhanced mechanical, electrical and thermal properties. Ceramic and metallic nanocomposites are at an earlier stage of development and a critical issue to resolve is optimising the dispersion of nanomaterials in the matrices. Pa...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the experimental results of accelerated aging tests conducted on three different types of polymer materials. Salt fog chamber tests were used to study the surface degradation modes for all materials. The work presented here was performed using a newly constructed fog chamber system that was able to control both chamber humidity and UV radiation. The changes in the surface morphology, material structure and leakage current were examined to study the influence of environmental humidity.

Energy Technology Data Exchange (ETDEWEB)

Wood-plastic composites (WPC) have been prepared with five low-grade woods, native to Syria, using three monomer systems; acrylamide, butylmethacrylate, and styrene, with methanol as the swelling solvent. Polymerization was induced at various radiation doses (10, 20, and 30 kGy) at a dose rate of 3.5 kGy/h using a {sup 60}Co gamma radiation source. Some physical properties of WPC, namely polymer loading and compression strength have been measured. The polymer loading decreases approximately with increasing density of the wood species used.

International Nuclear Information System (INIS)

Wood-plastic composites (WPC) have been prepared with five low-grade woods, native to Syria, using three monomer systems; acrylamide, butylmethacrylate, and styrene, with methanol as the swelling solvent. Polymerization was induced at various radiation doses (10, 20, and 30 kGy) at a dose rate of 3.5 kGy/h using a "6"0Co gamma radiation source. Some physical properties of WPC, namely polymer loading and compression strength have been measured. The polymer loading decreases approximately with increasing density of the wood species used. (author)

International Nuclear Information System (INIS)

Polymer composites are used in numerous applications. In spite of this fact, new developments are still under way to explore in other field of application of these materials and to tailor their properties for more extreme condition. A particular emphasis is focused on fillers content is summarized. Some steps towards the functionally graded materials are illustrated. The FT-IR spectroscopic studies revealed the information about curing of epoxy with fillers. It was observed that mechanical properties like tensile strength, hardness etc get enhanced up with filler contents. The effect of the different formulations were investigated and discussed for optimum process condition. (author)

Energy Technology Data Exchange (ETDEWEB)

The currently available propellants achieve about 95% of the combustion performance which can be expected theoretically at this time, consequently a technological breakthrough concerning new propellants have been demanded. Among high energy substances which are being studied, polymer azide which can continue combustion without relying on the oxidation reaction is a typical high energy substance to be used for a propellant of the next generation. The composite propellant which has polymer azide as fuel component and ammonium nitrate as oxidizer is considered to be the extremely promising propellant, since it provides no combution product which causes the environmental destruction. (6 figs, 4 refs)

Energy Technology Data Exchange (ETDEWEB)

An apparatus was designed and built for the purpose of exposing samples of solid polymers to varying temperatures, atmospheres and stress levels while quantitatively recording the resulting chemiluminescence. Preliminary data were acquired with this apparatus that show a correlation between an enhanced chemiluminescence signal at a low level of applied stress and a decrease in tensile strength for the most commonly used epoxy resin in high performance fiber composites, TGMDA DDS. The studies with cellular silicone cushions (which are used to accommodate thermal expansion and contraction) have defined the temperature regimes in which accelerated aging tests are valid for extrapolation to ambient temperature. Preliminary data on Kevlar fibers is also discussed.

Energy Technology Data Exchange (ETDEWEB)

Thermoplastic encapsulation has been extensively studied at Brookhaven National Laboratory`s (BNL) Environmental and Waste Technology Center (EWTC) as a waste encapsulation technology applicable to a wide range of waste types including radioactive, hazardous and mixed wastes. Encapsulation involves processing thermoplastic and waste materials into a waste form product by heating and mixing both materials into a homogeneous molten mixture. Cooling of the melt results in a solid monolithic waste form in which contaminants have been completely surrounded by a polymer matrix. Heating and mixing requirements for successful waste encapsulation can be met using proven technologies available in various types of commercial equipment. Processing techniques for thermoplastic materials, such as low density polyethylene (LDPE), are well established within the plastics industry. The majority of commercial polymer processing is accomplished using extruders, ...

International Nuclear Information System (INIS)

Thermoplastic polymer materials and the compounds made with them are being used more frequently for industrial components and for general use. However, the application of these materials for the production of complex shaped or relatively large pieces is limited, because of the difficulty and cost of making the necessary tool kit for the job. One solution is the use of the welding process. But the safe and reliable union of different thermoplastic material parts is not a simple process, even less so in the case of unions of large components. Welding by microwaves using polymer conductors can help, since the large scale equipment is available, and methods for continuous processes by microwave have been developed, that can be used to weld large and small components. Many thermoplastics (ex. polyethylene) do not absorb, or absorb very little, energy from microwaves. Polymer conductors, however, heavily absorb from microwaves ...

Energy Technology Data Exchange (ETDEWEB)

The chemical fixation of tritium in stearic acid followed by embedding the tritiated stearic acid into an epoxy resin proved to be a good method for permanent waste disposal of tritium gas. Tc-126 and Tc-136 hardener were used for this purpose. The polymerization temperature of the polymer products was found to be highly decreased by adding stearic acid and slightly decreased by adding stearic acid or by raising the temperature of the leachant medium and slightly decreased by irradiation. On the other hand, small improvement in the compressive strength of the polymer products was achieved by adding silica powder. The polymer product showed high flame points above 573 K although it contains stearic acid. DTA and TG analysis indicate that the thermal stability of polymer products containing stearic acid and silica powder is better than samples containing only stearic acid. Stearic acid was found to ...

Science.gov (United States)

We have been piloting web-based multimedia learning modules (MLMs), developed by the Physics Education Research Group at the University of Illinois at Urbana Champaign (UIUC), as a "prelecture assignment" in several introductory physics courses at California State Polytechnic University at Pomona. In this study, we report the results from a controlled study utilizing modules on electricity and magnetism as a part of a blended hybrid-online course. We asked students in the experimental section to view the MLMs prior to attending the face-to-face class, and to make sure this would not result in additional instructional time, we reduced the weekly class time by one-third. We found that despite reduced class time, student-learning outcomes were not hindered; in fact, the implementation of the UIUC MLMs resulted in a positive effect on student performance on conceptual tests and classroom discussion questions. (Contains 4 figures and 1 table.)

International Nuclear Information System (INIS)

The uncertainty of the elemental analysis is one of the major factors governing the utility of on-line Prompt Gamma Neutron Activation Analysis (PGNAA) in the blending and sorting of bulk materials. In this paper, a general method applicable to Gamma spectra processing is presented and applied to PGNAA in mineral industry. Based on the Fourier transform of spectra and their de-correlation in the Fourier space (the improvement of the conditioning of the correlation matrix), processing of overlapping of characteristic peaks minimizes the propagation of random errors, which optimizes the accuracy and decreases the detection limits of elemental analyses. In comparison with classical methods based on the linear combinations of relevant regions of spectra the improvement may be considerable, especially when several elements are interfering. The method is applied to four case stories covering both borehole logging and on-line analysis on conveyor belt of raw materials.

British Library Electronic Table of Contents (United Kingdom)

This study evaluated surface characteristics and overlaying properties of wood plastic composite (WPC) panels made from dry-blended rubber wood fiber-polypropylene (PP) powder formulations using a conventional flat-press process under laboratory conditions. Three levels of rubberwood fibers (Hevea brasiliensis), 40%, 50%, and 60%, based on the composition by weight, were mixed with the PP powder without and with 3% (based on weight) maleic anhydride grafted PP (MAPP) as a coupling agent. Contact angle measurements on the WPC samples were performed using a goniometer connected with a digital camera which collected one image per second. Roughness measurements, average roughness (R a), mean peak-to-valley height (R z), and maximum roughness (R y), were taken from the sanded samples along and ...

Energy Technology Data Exchange (ETDEWEB)

The OSP (Operating Safety Procedure) required for performance of electrical arc testing of CFC replacement fluids was renewed. Electrical breakdown tests at one atmosphere pressure have been performed for R-22, R-134a, and R-125/R-143a (50:50 blend; R-507), and breakdown products identified. No differences in HCFC breakdown products are seen in the presence or absence of lubricant oils. The design of the high pressure-high temperature test stand has been finalized, and construction initiated during this quarter. Three motor stators and rotors were received from Tecumseh Products Company for use in motor burnout tests. A test plan for the motor breakdown tests is in preparation.

Environmental Research Database

ObjectivesTo determine the reaction rate of slag during curing and factors affecting reactivity.~%~~%~To measure the rates of chloride ingress into concrete and the extent of chloride binding.~%~~%~To determine conditions for pitting corrosion and the nature of corrosion products.~%~~%~To characterise the reactions in slag-calcium alumina cement hydration and the nature of the products.~%~DescriptionBlast-furnace slag has latent hydraulic properties, giving considerable potential for commercial use in addition to its widespread use as a partial replacement for Portland cement, notably in alkali-activated slag (AAS) and slag-calcium alumina cement (CAC) concretes. Use of AAS concretes is already well-established in China and the former USSR, but their further application is hindered by lack of research into setting, hydration and durability, Slag/CAC blends are new materials whose chemistr [continued...

British Library Electronic Table of Contents (United Kingdom)

Carbon black is widely used as an active filler in the rubber industry to improve the physical properties of rubber. The surface energy of carbon black is high compared to that of various elastomers like styrene?butadiene rubber (SBR), butadiene rubber (BR) and ethylene?propylene?diene rubber (EPDM). The work aims at reducing the surface energy of carbon black by modifying its surface for application especially in rubber blends. The present paper looks into the possibility of using plasma polymerisation of acetylene as a surface modification technique for carbon black in comparison with silica. Thermogravimetric analysis, wetting behaviour with various liquids of known surface tension and time of flight secondary ion mass spectrometry (ToF-SIMS) were used to characterise the carbon black b...

British Library Electronic Table of Contents (United Kingdom)

Abstract Four methods were used to extract length scales from mixing data: the maximum striation thickness, point-to-nearest-neighbour (PNN) distributions, the correlogram and the variogram. Four test data sets were analysed: blending in a micromixer; particle dispersion in a stirred tank; dispersion of a smoke plume and a pulse tracer test in a reactor. The maximum striation thickness captures the largest length scale. The PNN method quantifies differences between clustered, random and regular spatial distributions. The correlogram calculation cannot be consistently used for all types of mixing data and has therefore been rejected. The variogram reveals both large-scale segregation and periodicity. Sub-sampling is needed to isolate smaller structures. The variogram, PNN and transect metho...

Energy Technology Data Exchange (ETDEWEB)

Encapsulation of a unique isotopic blend of krypton and xenon gas employs a special application of laser technology. The encapsulated gas is then used as the primary medium for detection and identification of failed nuclear fuel rods. The use of gas tagging as a means of detecting and identifying failed nuclear fuel rods has been successfully demonstrated and used by the Argonne National Laboratory, Experimental Breeder Reactor (EBR-2) Project, and the Westinghouse Hanford Company (WHC), Fast Flux Test Facility (FFTF) Fast Breeder Reactor Program. The Power Reactor and Nuclear Fuel Development Corporation (PNC) of Japan has selected this leak detection system for use in their MONJU Prototype Reactor fuel assemblies. The MONJU reactor is almost identical in design to the highly successful FFTF reactor, which is currently in standby status.

Science.gov (United States)

Hydrogenation residue is the product left over when petroleum residue feedstocks (or coal) are treated by, e.g. the Veba Combi Cracking (VCC) process. Many tests in semitechnical and full-sized coke ovens were carried out with hydrogenation residue (HR) as an additive in coking coal blends for the production of blast furnace coke or foundry coke. The results of the investigations reported in this paper demonstrate that HR is a very promising alternative for enlarging the coking coal basis compared to other processes or the use of other additives. The application of HR on an industrial scale did not indicate any negative impact on the handling of the hydrogenation residue or on the operation of the coke oven battery.

British Library Electronic Table of Contents (United Kingdom)

The need to evolve with our ever-changing student bodies has never been as great as it is today, particularly given the advanced technological aptitude of today's students. This retrospective study evaluates student outcomes as they relate to overall course score and composite quiz and examination scores from a basic pharmacology course taught over three separate semesters using three different lecture delivery modalities: traditional in-class; blended; and online-only. A total of 48 students from a US university's health sciences bachelor degree programme enrolled in one of these three sections between 2009 and 2010. A one-way analysis of variance test with Tukey's honestly significant difference post hoc testing was utilized to determine if any statistical difference existed between the ...

Energy Technology Data Exchange (ETDEWEB)

A study to determine how much energy can be recovered from a Florida citrus processing plant was conducted. The production of ethyl alcohol in particular was examined as it is thought to represent the greatest potential for immediate energy recovery. Three-fourths of the energy expended to produce, harvest, process and market a box of fruit was recoverable using existing technology, i.e. 78,500 Btu/ box of fruit recoverable from a total energy expenditure of 107,800 Btu/ box of fruit. Aside from the actual cost benefits of recovering energy in the form of ethanol, the food processor is also helping to reduce the foreign-oil imports by the blending of ethyl alcohol with unleaded gasoline to form gasohol.

Energy Technology Data Exchange (ETDEWEB)

An array of sonic transducers, useful for medical ultrasonic imaging, has individual sections thereof separately coupled for forming separate beams of sonic energy which converge, respectively, to separate foci along a common axis of the beams. The ratio of the diameter of the radiating aperture of the array relative to a wavelength of the sonic energy is chosen to provide a moderate degree of focusing so that the depth of field at one focus blends with the depth of field of the next focus. Thereby, there is formed a continuous region of substantially uniform intensity of sonic radiation along the common beam axis. Circuitry is provided for selecting one or more specific foci dependent on the bounds of a selected region to be insonified. Upon reception of sonic energy, circuitry is provided for selecting one or more specific foci as a function of the time of travel of an echo from a subject being observed to approximate a continuously varying focus in accordance ...

British Library Electronic Table of Contents (United Kingdom)

Cellulose sausage cellulose casings are used extensively in the manufacture of sausages in meat packaging. After stripping the meat, spent casings mainly contain cellulose and residual meat juice with salt, nitrate and nitrite. Disposal of spent sausage casings has serious economic and environmental concerns for the sausage industry. This work describes bioconversion of spent cellulose casings (SCC) into enzymes, lactic acid and ethanol by using cellulolytic fungi, lactobacillus and yeasts. The solid substrate cultivation (SSC) of Trichoderma reesei RUT C-30 on SCC and blends gave a maximum of 152 filter paper cellulase (FPase) activity and about 100 carboxymethylcellulase activity (CMCase)/g dry weight substrate. The SSC produced enzyme-rich casing with 50 FPase when directly mixed as suc...

British Library Electronic Table of Contents (United Kingdom)

Luminescent materials are widely used for imaging and sensing owing to their high sensitivity, rapid response and facile detection by many optical technologies. Typically materials must be chemically tailored to achieve intense, photostable fluorescence, oxygen-sensitive phosphorescence or dual emission for ratiometric sensing, often by blending two dyes in a matrix. Dual-emissive materials combining all of these features in one easily tunable molecular platform are desirable, but when fluorescence and phosphorescence originate from the same dye, it can be challenging to vary relative fluorescence/phosphorescence intensities for practical sensing applications. Heavy-atom substitution alone increases phosphorescence by a given, not variable amount. Here, we report a strategy for modulating ...

International Nuclear Information System (INIS)

Two sources of ultraviolet (UV) radiation with peak wavelengths in the UV-C or UV-B ranges were compared for their ability to sterilize contact lenses infected with Pseudomonas aeruginosa, Streptococcus pneumoniae, Acanthamoeba castellani, Candida albicans, and Aspergillus niger. Also examined was the effect of prolonged UV light exposure on soft and rigid gas permeable (RGP) contact lenses. The UV-C lamp (253.7 nm, 250 mW/cm2 at 1 cm) was germicidal for all organisms within 20 minutes but caused destruction of the soft lens polymers within 6 hours of cumulative exposure. UV-C caused damage to RGP lenses in less than 100 hours. The UV-B lamp (290-310 nm, 500 mW/cm2 at 1 cm) was germicidal for all organisms tested (except Aspergillus) with a 180-minute exposure and caused less severe changes in the soft lens polymers than did the UV-C lamp, although cumulative exposure of 300 hours did substantially weaken the soft lens material. RGP materials ...

Energy Technology Data Exchange (ETDEWEB)

Poly(methyl methacrylate), PMMA, Acrigel, a Brazilian polymer, is used in the manufacture of medical supplies sterelizable by ionizing radiation. However, when PMMA is gamma-irradiated it undergoes main chain scissions, which promote molecular degradation causing reduction in its mechanical properties. Therefore, radiolytic of PMMA is important for it to become commercially radiosterizable. In this work some commercial additives, originally used in photo-and thermo-oxidate stabilization of polymers, were tested. Only two additives, type HALS (Hindered Amine Light Stabilizer), denoted Scavenger, showed a good protective quality. The investigation of radiation-induced main scissions was carried out by viscosimetric method. The most effective additive, added to the polymer system at 0.3 w/w%, promotes a great molecular radioprotection of 93%. That means a reduction of G-value (scissions/100 eV) from 0.611 to 0.053. In ...

Energy Technology Data Exchange (ETDEWEB)

The ink jet printing technology is a relatively novel technique in development of organic electronic devices. The technique consists of working out depositions of organic layers by a piezo-based ink jet printer. In this work polymer conducting films deposited by ink jet printing technique on different plastic substrates has been demonstrated. The poly(3,4-ethylenedioxythiofene)/poly(4-styrenesulfonate) [PEDOT/PSS] and glycerol-modified PEDOT/PSS [G-PEDOT/PSS] were used like conducting inks to be applied on polyester and polyethylene terephthalate (PET) substrates. By means of the change of substrate associated to the deposition number or type of polymer ink used for printing of the conducting films, the sheet resistance can be modified. Such a behavior suggests that plastic substrate fulfills an important role for the changing of sheet resistance of the PEDOT/PSS and G-PEDOT/PSS films made by ink jet printing technique. Films obtained from this ...

Energy Technology Data Exchange (ETDEWEB)

Samples of ultra-high molecular weight polyethylene (UHMWPE) and nylon 66, of grades suitable for use in medical prostheses, were subjected to irradiation using a /sup 60/Co source. The effects of a 10 Mrad dose on percentage crystallinity, tensile behaviour and dynamic mechanical response were established 3 days after irradiation at intervals over a one year period. Crystallinity in UHMWPE was found to increase progressively during this period with consequent changes in mechanical behaviour. It is proposed that the observed ageing process arises from the breakdown of metastable groups in the polymer, which are formed on irradiation, with consequent release of long inter-lamella tie chains. This removes an inhibition to crystal perfection processes, which can occur at room temperature in polyethylene. Infra-red spectroscopic evidence supports the proposal that the metastable species is peroxy or hydroperoxy and that this decomposes on ageing to a carbonyl group, ...

Environmental Research Database

Objectives1. To develop new photoactive materials and fabricate demonstration QD (quantum dot) solar cells. This will be achieved by:~%~1.1. Materials preparation and characterisation of QD/polymer systems~%~1.2. Optimising structures of QDs, nanorods and polymer for quantum yield and charge transfer~%~1.3 Fabricating demonstration QD/polymer solar cells and measuring power conversion efficiencies~%~2. To demonstrate multiexciton generation (MEG) and harvesting within nanostructured QDs. This will involv [continued...]DescriptionWidespread implementation of photovoltaic electricity to meet changing energy demands requires a step-change in the cost of photovoltaic power. This proposal assembles a consortium of chemists, physicists, materials scientists and electrical engineers from The University of Manchester and Imperial College London to address this need through the development of new low-cost, high-efficiency, ...

Energy Technology Data Exchange (ETDEWEB)

The confocal Raman micro-spectroscopy has been used for the study of a Lithium/polymer electrolyte-LiTFSI/V{sub 2}O{sub 5} type battery in which the polymer electrolyte thickness is of about 80 {mu}m. The analysis is performed on the side of the battery thanks to a specially designed cell which preserves all the characteristics of the real system. The analysis is performed on 20 points aligned between the anode and the cathode and with a depth of several tenth of {mu}m. The analysis of data obtained during charging/output cycles allows to evaluate the gradients of salt concentration inside the electrolyte, the pollutions of LiOH, Li{sub 2}CO{sub 3}, Li{sub 2}O and Li{sub 3}N -type at the lithium interface, but also the structural modifications of the cathode material. The in-situ study of concentration gradients inside the electrolyte is of prime importance for the understanding of dendrites growth. (J.S.) 11 refs.

CERN Document Server

We show the existence of global-in-time weak solutions to a general class of coupled FENE-type bead-spring chain models that arise from the kinetic theory of dilute solutions of polymeric liquids with noninteracting polymer chains. The class of models involves the unsteady incompressible Navier-Stokes equations in a bounded domain in two or three space dimensions for the velocity and the pressure of the fluid, with an elastic extra-stress tensor appearing on the right-hand side in the momentum equation. The extra-stress tensor stems from the random movement of the polymer chains and is defined by the Kramers expression through the associated probability density function that satisfies a Fokker-Planck-type parabolic equation, a crucial feature of which is the presence of a center-of-mass diffusion term. We require no structural assumptions on the drag term in the Fokker-Planck equation; in particular, the drag term need not be corotational. With ...

Energy Technology Data Exchange (ETDEWEB)

Different experimental measurements (Theology, granulometry, XRD) were carried out in order to study the main properties of bentonite suspensions in presence of anionic additives at different concentrations. These additives are: Sodium Dodecyl Sulfate (SDS) as surfactant, a flexible polymer (Sodium Carboxy Methyl Cellulose, CMC) and a semi-rigid polymer (Xanthan gum). It has been shown that the structural nature of anionic additive influences directly the mixtures viscoelastic and flow behavior. The steric effect of the surfactant modifies the Face-Edge interactions and yields changes of the mixtures rheological behavior at low deformation rates. Polymers act by coating each clay particle and prevent their agglomeration. Therefore, bentonite has no direct effect on the rheological behavior of the mixtures: the additives are responsible for the mechanisms of de-structuration and structure reorganization as well as the ...

Energy Technology Data Exchange (ETDEWEB)

Theoretical and experimental studies have been carried out on the combustion of azide polymers used as a binder in high-energy propellants. AMMO (3-azidemethyl-3`-methyloxetane) is one of the energetic azide polymers which contain N3 groups in their molecular structures. EDNA (ethylenedinitramine) is a linear nitramine which has modest properties in the flame temperature and the molecular weight of burned gases as compared with HMX (cyclotetramethylenetetranitramine) and NQ (nitroguanidine). In this study, the burning rate characteristics of azide/nitramine propellants were investigated in order to gain a wide spectrum of burning rate. As a result, the burning rate of AMMO/EDNA propellant is higher than that of AMMO/HMX propellant and the pressure exponent of AMMO/EDNA propellant is lower than that of AMMO/HMX propellant. Both AMMO/EDNA and AMMO/HMX propellants exhibited the same combustion wave structure as inert ...

International Nuclear Information System (INIS)

Comprehensive investigation has been made into the application of the polymerization hardening by radiation, particularly electron beam, to the composites of polymers and other materials. The report is divided into four parts, namely 1) characteristics and problems of the reaction of curing by radiation polymerization, 2) improvement of the bonding capability of high molecular weight materials, 3) bonding by radiation, and 4) composites made by the impregnation and polymerization hardening of monomers. The first part includes the effects of dose rate, temperature rise during the hardening, the peculiarity of electron beam irradiation at high dose rate, reaction environment and additive effects. Main conclusions are as follows: caution must be taken to the amount of residual double bonds because they affect the quality of hardened polymers; the polymerization hardening reaction at high dose rate cannot be analogized by that at low dose rate; and ...

British Library Electronic Table of Contents (United Kingdom)

We propose and demonstrate a facile room-temperature synthetic method for obtaining water-soluble magnetic Fe3O4 nanoparticles (NPs) by combining the in situ synthesis and decomposition of a magnetic polymer hydrogel. The Fe3O4 NPs with average diameters of 6.3-8.3nm were synthesized in a cross-linked polyacrylamide (PAAm) hydrogel by coprecipitating iron ions. The decomposition of the magnetic polymer hydrogel by an aqueous solution of sodium hydroxide led to the transfer of Fe3O4 NPs into the aqueous medium. The NPs can be dispersed stably in water for more than three months. The Fe3O4 NPs were characterized by X-ray photoelectron spectra (XPS), X-ray powder diffraction (XRD), transmission electron microscope (TEM), and Fourier transform infrared spectroscopy (FT-IR). The saturation magn...

Energy Technology Data Exchange (ETDEWEB)

In this program, contemporary solidification agents are being investigated relative to their applications to major fuel cycle and non-fuel cycle low-level waste (LLW) streams. Work is being conducted to determine the range of conditions under which these solidification agents can be applied to specific LLW streams. These studies are directed primarily towards defining operating parameters for both improved solidification of problem wastes and solidification of new LLW streams generated from advanced volume reduction technologies. Work is being conducted to measure relevant waste form properties. These data will be compiled and evaluated to demonstrate compliance with waste form performance and shallow land burial acceptance criteria and transportation requirements (both as they exist and as they are modified with time). 6 tables.

British Library Electronic Table of Contents (United Kingdom)

Polymer insulating materials used in radioactive environments are subjected to a risk of surface degradation caused by tracking. The tracking behavior becomes more complex with the presence of magnetic field. This paper presents investigation of tracking failure of gamma-ray irradiated polybutylene naphthalate (PBN) and polybutylene terephthalate (PBT) under magnetic field. The samples were irradiated in air up to 100 kGy and then up to 1000 kGy with dose rate of 10 kGy/h by using a 60Co gamma-source. Magnetic field Formula Not Shown with flux density of 250 mT was assembled perpendicularly to electric field Formula Not Shown , which gave rise to relative angle between Formula Not Shown and surface normal vector Formula Not Shown of 0degree, 90degree and 180degree, respectively. The experi...

Energy Technology Data Exchange (ETDEWEB)

In this work it is made a study of the structure and electric properties of chlorate polyethylene (PE-CI) with double and simple bonds obtained by continuous plasma with resistive coupling to 13.5 MHz. The synthesis conditions are power between 10 and 14 W and pressure of (6-7) x 10{sup -2} Torr. The synthesized PE-Cl in that way is soluble in acetone what indicates that probably is formed of short chains and not it shows the generalized inter crossing that is presented in some syntheses by plasma and that it can degrade the electric properties of these polymers. The IR and XPS analysis show the vibration of the C-C, C=C and C-CI bonds. The morphology of the polymer after being dissolved shows a compact and flat configuration. The electric conductivity has an approximately lineal behavior in an interval of 35 to 90% of relative humidity. (Author)

British Library Electronic Table of Contents (United Kingdom)

Coordination of CoCl2 solutions to the silica polyamine composite, WP-1, made with the branched polymer polyethylenimine (PEI) shows irreversible binding resulting from surface oxidation of the Co2+-Co3+. This is not the case for the silica polyamine composite BP-1 made with the linear polymer polyallylamine where reversible binding and no oxidation is observed. These observations suggested that oxidation of the cobalt was related to the greater coordination number available with the branched polyamine relative to the linear polyamine. A study of the kinetics of cobalt binding to WP-1 indicated initial loading of Co2+ at relatively low coordination number followed by desorption of Co2+ leading to oxidation and irreversible binding. Exclusion of oxygen from the composite-cobalt solution mix...

British Library Electronic Table of Contents (United Kingdom)

Summary: The surface coverage of amorphous silica gels used in the synthesis of silica polyamine composites has been investigated by 29Si NMR. By diluting the polyamine anchor silane, chloropropyl trichlorosilane, with methyl trichlorosilane it was found that surface coverage could be markedly improved for a range of amine polymers after grafting to the silica surface. The commensurate decrease in the number of anchor points and increase in the number of free amines results in an increase in metal capacity and/or an improvement in capture kinetics. Solid state CPMAS-13C NMR has been employed to investigate the structure and metal ion binding of a series of these composite materials. It is reported that the highly branched polymer, poly(ethyleneimine) (PEI) exhibits much broader 13C NMR res...

British Library Electronic Table of Contents (United Kingdom)

An effective rehabilitation strategy is proposed to enhance the strength and stiffness of the beam-column joint in this study. An analytical model is proposed to predict the column shear of the joints strengthened with carbon fiber reinforced polymer (CFRP). Three full scale interior beam-column joints, including two specimens strengthened with CFRP and one prototype specimen, are tested in this study. The specimens are designed to represent the pre-seismic code design construction in which there is no transverse reinforcement. A new optical non-contact technique, digital image correlation (DIC), which can measure the full strain field of specimen, is used to measure and observe the full strain field of the joint. The experimental results show that the beam-column joints strengthened with ...

British Library Electronic Table of Contents (United Kingdom)

Abstract A one step method was used to prepare stable aqueous nanocomposite dispersions based on cellulose whiskers extracted from the rachis of the date palm tree and a poly(styrene co 2 ethyl hexylacrylate) copolymer via miniemulsion polymerization. A reactive silane, i.e., methacryloxypropyl triethoxysilane was added to stabilize the dispersion and favor the anchoring of the whiskers on polymer particles. Dynamic light scattering was used to study the effect of the silane and whiskers contents on the average particle size of the polymer. Nanocomposites materials were prepared from these dispersions using a casting/evaporation method. The effect of the silane and whiskers contents on the thermal and mechanical properties were studied using differential scanning calorimetry and dynamic me...

Energy Technology Data Exchange (ETDEWEB)

Aluminium AA5182 coupons covered by a polyaniline film in the emeraldine base (EB) form showed increasing corrosion potential and decreasing corrosion current as a function of the thickness of the polymer layer. The cathodic reaction was proved not limited by diffusion of species inside the electrolyte solution and oxygen had no effect on the electrochemical behaviour of the coated samples. An EB coating on indium tin oxide conducting layer appeared slightly electroactive in neutral media. The IR spectra of aluminium coated samples, before and after heating in argon atmosphere, confirmed a redox reaction between the polymer film and the metal. This galvanic coupling can explain the good protective behaviour of emeraldine base against corrosion of aluminium.