Energy Technology Data Exchange (ETDEWEB)

In the development of high performance heat transfer surface on a compact heat exchanger, it was clarified that how reattachment point heat transfer and fluid flow are affected by channel width, at the same time, an evaluation of heat transfer performance and an investigation of optimum channel width were carried out. The channel system used in the experiment is as follows; (1) blow-off type with rectangular section channel, (2) span length of 200 mm, (3) wave length (pitch) of 80 mm, and (4) channel length of 12.5 wave length. The channel Reynolds number was set at about 10/sup 4/ which is relatively higher than the current studies. The results of the experiment were summarized as follows. (1) The channel width H has relevance to the phase difference between ...

International Nuclear Information System (INIS)

This paper evaluates the electric current terms from the longitudinal gradient of the longitudinal electric field in Bipolar Field-Effect-Transistors (BiFETs) with a pure base and two MOS gates operating in the unipolar (electron) current mode. These nMOS-BiFETs, known as nMOS-FinFETs, usually have electrically short channels compared with their intrinsic Debye length of about 25 #mu#m at room temperatures. These longitudinal electric current terms are important short-channel current components, which have been neglected in the computation of the long-channel electrical characteristics. This paper shows that the long-channel electrical characteristics are substantially modified by the longitudinal electrical current terms when the physical channel length is less than 100 nm.

Energy Technology Data Exchange (ETDEWEB)

Recently there has been growth, in interest in non-equilibrium interaction of half-period long optical pulses with matter. To date the optical pulses have been produced by chopping out a half-period long segment from a longer pulse using a semiconductor switch driven by a femtosecond laser. In this paper we present new methods for producing tunable ultra-short optical pulses as short as half an optical period using a free-electron laser driven by electron bunches with a duration a fraction of an optical period. Two different methods relying on the production of coherent spontaneous emission will be described. In the first method we show that when a train of ultra-short optical pulses as short as one half period. We present calculations which show that the small signal gain is unimportant in the early stages of radiation build up in the cavity when the startup process is dominated by coherent spontaneous emission. To support our proposed method ...

International Nuclear Information System (INIS)

A commercial CFD code, Fluent, has been used to analyse the design of a filter-press reactor operating with characteristic linear flow velocities between 0.024 and 0.192 m s-1. Electrolyte flow through the reactor channel was numerically calculated using a finite volume approach to solve the Navier-Stokes equations. The length of the channel was divided into 7 sections corresponding to distances of 0, 0.01, 0.04, 0.08, 0.12, 0.14 and 0.15 m from the electrode edge nearest to the inlet. The depth of the channel was divided into three planes parallel to the channel bottom. For each channel section, a velocity profile was obtained at each depth together with the average velocity in each plane. The flow predictions show that the flow development, as the electrolyte passes through the cell, is strongly affected by the manifold causing strong vortex structures at the ...

Energy Technology Data Exchange (ETDEWEB)

The invention relates to a pulsed laser ablation method of metals and/or dielectric films from the surface of a wafer, printed circuit board or a hybrid substrate. By utilizing a high-energy ultra-short pulses of laser light, such a method can be used to manufacture electronic circuits and/or electro-mechanical assemblies without affecting the material adjacent to the ablation zone.

British Library Electronic Table of Contents (United Kingdom)

It has been considered that dry-out occurs easily in boiling heat transfer for a small channel, a mini- or microchannel, because the channel was easily filled with coalescing vapor bubbles. In the present study, the experiments of subcooled flow boiling of water were performed under atmospheric conditions for a horizontal rectangular channel for which the size is 1 mm height and 1 mm width, with a flat heating surface of 10 mm length and 1 mm width placed on the bottom of the channel. The heating surface has a top of copper heating block and is heated by ceramic heaters. In the high heat flux region of nucleate boiling, about 70-80% of the heating surface was covered with a large coalescing bubble and the boiling reached critical heat flux as observed by high-speed video. In the beginning ...

British Library Electronic Table of Contents (United Kingdom)

The present paper investigates the peristaltic transport of a couple stress fluid in an asymmetric channel with the effect of the induced magnetic field. The exact solutions of momentum and the magnetic field equations have been calculated under the assumptions of long wave length and low but finite Reynolds number. The expression for pressure rise has been computed numerically using mathematics software Mathematica. The graphical results have been presented to discuss the physical behavior of various physical parameters of interest. Finally, the trapping phenomena have been discussed for various physical parameters.

Energy Technology Data Exchange (ETDEWEB)

A wavelength division multiplexer/demultiplexer having optical path lengths between a fiber array and a Fourier transform lens, and between a dispersion grating and the lens equal to the focal length of the lens. The optical path lengths reduce losses due to angular acceptance mismatch in the multiplexer. Close orientation of the fiber array about the optical axis and the use of a holographic dispersion grating reduces other losses in the system. Multi-exposure holographic dispersion gratings enable the multiplexer/demultiplexer for extremely broad-band simultaneous transmission and reflection operation. Individual Bragg plane sets recorded in the grating are dedicated to and operate efficiently on discrete wavelength ranges.

Science.gov (United States)

We have analyzed the MHD flow of a conducting couple stress fluid in a slit channel with rhythmically contracting walls. In this analysis we are taking into account the induced magnetic field. Analytical expressions for the stream function, the magnetic force function, the axial pressure gradient, the axial induced magnetic field and the distribution of the current density across the channel are obtained using long wavelength approximation. The results for the pressure rise, the frictional force per wave length, the axial induced magnetic field and distribution of the current density across the channel have been computed numerically and the results were studied for various values of the physical parameters of interest, such as the couple stress parameter ?, the Hartmann number M, the magnetic Reynolds number R and the time averaged mean flow rate ?. Contour plots for the stream and magnetic force ...

Energy Technology Data Exchange (ETDEWEB)

Experiments on heat transfer augmentation in a rectangular cross-section water channel are reported. The channel geometry is designed to excite normally damped Tollmein-Schlichting modes in order to enhance mixing. In this experiment, a hydrodynamically fully developed flow encounters a test section where one channel boundary is a series of periodic, saw-tooth, transverse grooves. Free shear layers span the groove openings, separating the main channel flow from the circulating vortices contained within each cavity. The periodicity length of the grooves is equal to one-half of the expected wavelength of the most unstable mode. The remaining channel walls are flat, and the channel has an aspect ratio of 10:1. Experiments are performed over the Reynolds number range of 300 to 15,000. Streakline flow visualization shows that the flow is steady ...

International Nuclear Information System (INIS)

The effect of anode length and operating gas pressure on the x-ray emission from a nitrogen-filling modified plasma focus device has been investigated. The time-resolved investigation of x ray was carried out by using a five-channel photodiode x-ray spectrometer. The maximum x-ray yield is seen to increase with the increase in the anode length from 110 to 125 mm. Further increase in the anode length to 130 mm causes the x-ray yields to decrease. The highest x-ray yield of 4.5 J into 4#pi# sr was found for 125 mm anode length, which is 0.2% of the input energy. The average x-ray photon energy was estimated by using half-value thickness method and found to be 8.4 keV. The electron temperature of the plasma was estimated to be around 3 keV by x-ray intensity ratio method. The space-resolved x-ray-emitting zones for all the anodes were captured by a pinhole-based x-ray imaging camera ...

British Library Electronic Table of Contents (United Kingdom)

Microcrystalline-Si thin-film transistors (?C-Si TFTs) formed by using the source/drain contact electrode of self-aligned palladium silicide have been investigated. Both the self-aligned palladium silicided scheme and the previous top-gate staggered structure employ two-mask process steps for fabricating ?C-Si TFTs. However, the self-aligned palladium silicided scheme would cause better device characteristics than the top-gate staggered structure, primarily due to more carrier tunneling. For a gate length of 2 ?m, as compared to the top-gate staggered scheme, this silicided scheme can result in a 40% improvement of on-state current. In addition, as the gate length is reduced to 1 ?m, considerable short-channel effect is caused for both the device schemes.

CERN Document Server

The optical birefringence of rod-like nematogens (7CB, 8CB), imbibed in parallel silica channels with 10 nm diameter and 300 micrometer length, is measured and compared to the thermotropic bulk behavior. The orientational order of the confined liquid crystals, quantified by the uniaxial nematic ordering parameter, evolves continuously between paranematic and nematic states, in contrast to the discontinuous isotropic-to-nematic bulk phase transitions. A Landau-de Gennes model reveals that the strength of the orientational ordering fields, imposed by the silica walls, is beyond a critical threshold, that separates discontinuous from continuous paranematic-to-nematic behavior. Quenched disorder effects, attributable to wall irregularities, leave the transition temperatures affected only marginally, despite the strong ordering fields in the channels.

Science.gov (United States)

The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in-place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing 3-dimensional and multi-component seismic area is being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with extended-reach jetting lance and other ultra-short radius lateral technologies. Improved completion efficiency, additional wells at closer spacing and better estimates of oil-in-place will result in additional oil production by primary and enhanced recovery processes.

Science.gov (United States)

The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in-place, methods for improved completion efficiency and the suitability of waterflooding in Red River and Ratcliffe shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing three-dimensional and multi-component seismic are being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with extended-reach jetting lance and other ultra-short-radius lateral technologies. Improved completion efficiency, additional wells at closer spacing and better estimates of oil in place will result in additional oil recovery by primary and enhanced recovery processes.

Energy Technology Data Exchange (ETDEWEB)

Bubbly and slug flows have been analyzed using the afore-mentioned techniques. An image series of bubbly-slug flow is shown. The image separation time is 17 ms, and the total flow length is {approx} 10 cm. A circular eddy pattern that follows the slug can be readily seen and tracked, although reliability is low due to motion in the transverse direction. This motion also adds considerable error to the velocity measurements using image recognition technique. This will increase the reliability and accuracy of the tracking method.

Energy Technology Data Exchange (ETDEWEB)

Measurements are presented of the distribution of average friction factors (f) as well as local and average ({ovr Nu}) heat transfer coefficients for fully developed channel flows with two rib-roughened opposite walls. The temperature measurements were made by using both a laser holographic interferometer and thermocouples. In addition, the reattachment length was determined by flow visualization. The Reynolds number (Re) was varied from 5.0 {times} 10{sup 3} to 5.4 {times} 10{sup 4}; the rib pitch-to-height ratios (Pi/H) were 10, 15, 20; and the rib height-to-hydraulic diameter ratios (H/De) were 0.063, 0.081, and 0.106. The detailed results allowed the peaks of heat transfer augmentation and the regions susceptible to hot spots to be located and allowed the relative contribution of the rib surface and the channel wall to the heat transfer augmentation to be determined. Moreover, relative to a smooth duct, the enhancement ...

Science.gov (United States)

Staggered arrays of dimples printed on opposite surfaces of a cooling channel is formulated numerically and optimized with hybrid multi-objective evolutionary algorithm and Pareto optimal front. As Pareto optimal front produces a set of optimal solutions, the trends of objective functions with design variables are predicted by hybrid multi-objective evolutionary algorithm. The problem is defined by three non-dimensional geometric design variables composed of dimpled channel height, dimple print diameter, dimple spacing, and dimple depth, to maximize heat transfer rate compromising with pressure drop. Twenty designs generated by Latin hypercube sampling were evaluated by Reynolds-averaged Navier-Stokes solver and the evaluated objectives were used to construct Pareto optimal front through hybrid multi-objective evolutionary algorithm. The optimum designs were grouped by k-means clustering technique and some of the clustered points were evaluated ...

Energy Technology Data Exchange (ETDEWEB)

This paper reports on superconductor-semiconductor-superconductor (S-N-S) weak-link junctions with the normal layer of Si or InSb thin films were prepared by using focused ion beam (FIB), and electrical properties were measured. Whereas InSb thin films on single crystals did not have an intrinsic mobility, S-N-S junction with InSb shows the characteristics of Josephson S-N-S junction. A 200nm-thick film of InSb deposited on MgO had a mobility of 83 cm{sup 2}.V {center dot} s and a carrier density of 6.5 {times} 10{sup 17} cm{sup {minus}3} at 4.2K. The coherence length {xi}{sub n} was computed to be 17 nm from these experimental data, and we obtained critical superconducting current Ic of 100 {mu} A for the S-N-S junction which had a line width of 10{mu} m and a channel length of 20 nm.

Energy Technology Data Exchange (ETDEWEB)

The current work focuses on the pressure drop, heat transfer and stability in two phase flow in microchannels with hydraulic diameter of less than one hundred microns. Experiments were conducted in smooth microchannels of hydraulic diameter of 45, 65 {mu}m, and a rough microchannel of hydraulic diameter of 70 {mu}m, with deionised water as the working fluid. The local saturation pressure and temperature vary substantially over the length of the channel. In order to correctly predict the local saturation temperature and subsequently the heat transfer characteristics, numerical techniques have been used in conjunction with the conventional two phase pressure drop models. The Lockhart-Martinelli (liquid-laminar, vapour-laminar) model is found to predict the two phase pressure drop data within 20%. The instability in two phase flow is quantified; it is found that microchannels of smaller hydraulic diameter have lesser instabilities as compared to ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of the study is to investigate the heat transfer augmentation method for a wavy channel type heat exchanger. Experimental studies were carried out, by installation of flow guide-plates with simple structure, to clarify the effects on the augmentation whether the effects are brought by the flow acceleration or by the increase of intensity of turbulence due to the flow seperation, and to determine optimum shape of flow guide-plates. The shape and dimensions of the experimental apparatus are as follows; channel width H of 30 mm, rectangular section with breadth of 300 mm, wavy duct with a bend angle of 60/sup 0/ and straight pipe of 2H length. Air stream was flowed through the duct with Reynolds number of 1.7 x 10/sup 4/ only. As the results, following conclusions were obtained. (1) Wavy duct with large bend angle and without inserting flow guide-plates could not be expected large effects on the heat transfer ...

Energy Technology Data Exchange (ETDEWEB)

The performance of scanning driver circuits fabricated with self-aligned aluminum gate polysilicon thin-film transistors (TFT's) is demonstrated. After the gate electrode patterning, the fabrication process temperature is kept below 400degC to enable the use of aluminum gate electrodes. The low-temperature crystallization phenomenon, which occurs when protons are implanted simultaneously with boron or phosphorus dopants, is employed to eliminate the 600degC activation-annealing process. A maximum clock frequency of about 2.0 MHz is achieved when the driver operating voltage is 24 V and the TFT channel length is 12 [mu]m. (author).

British Library Electronic Table of Contents (United Kingdom)

An experimental investigation on the air/water counter-current two-phase flow in a horizontal rectangular channel connected to an inclined riser has been conducted. This test-section representing a model of the hot leg of a pressurized water reactor is mounted between two separators in a pressurized experimental vessel. The cross-section and length of the horizontal part of the test-section are (0.25mx0.05m) and 2.59m, respectively, whereas the inclination angle of the riser is 50degree. The flow was captured by a high-speed camera in the bended region of the hot leg, delivering a detailed view of the stratified interface as well as of dispersed structures like bubbles and droplets. Countercurrent flow limitation (CCFL), or the onset of flooding, was found by analyzing the water levels mea...

Energy Technology Data Exchange (ETDEWEB)

Abstract not provided

Science.gov (United States)

The purpose of this project is to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in- place, methods for improved completion efficiency and the suitability of waterflooding in certain shallow-shelf carbonate reservoirs in the Williston Basin, Montana, North Dakota and South Dakota. Improved reservoir characterization utilizing 3-dimensional and multi-component seismic area is being investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterization tools are integrated with geological and engineering studies. Improved completion efficiency is being tested with extended- reach jetting lance and other ultra-short radius lateral technologies. Improved completion efficiency, additional wells at closer spacings better estimates of oil-in-place will result in additional oil production by primary and enhanced recovery processes. Technical progress is described for field ...

International Nuclear Information System (INIS)

T_2 weighted ultra-short turbo spin echo sequences were used in five individuals with variations in echo times, delayed triggering and echo intervals. To reduce movement artifacts all examinations were carried out with ECG and respiratory triggering. The sequences giving optimal image quality were then employed in 19 patients having various pulmonary abnormalities. Image resolutions, artifacts, image contrasts and diagnostic value were then judged by two observers and compared with CT. In the first study, a diastole-triggered UTSE sequence with the shortest echo proved optimal (T_E=90 ms, T_R=2-4 s, echo=9 ms, turbo factor=19). In the patient series studied, MRT was inferior to CT with regard to resolution and number of artifacts, but better in respect of contrast and diagnostic value. Using UTSE of the lung, MRT can produce images of good quality. Compared with CT, contrast is better with MRT, offering diagnostic advantages for MRT. (orig./MG).

International Nuclear Information System (INIS)

On-power refuelling is an integral feature of PHWR units. The most notable aspect of refuelling system of 540 MWe PHWR (TAPP-3 and 4) is that the FM Head is based on rack and pinion mechanism for B-ram and C-ram of Ram assembly. Latch ram used during plug operations, is assembled in between B-ram and C-ram and is moved by a ballscrew driven by oil hydraulic motors. This unique design has been employed for the first time in a PHWR unit. In comparison, B-ram is ballscrew driven and C-ram is moved by heavy water hydraulic force in FM Heads of 220 MWe PHWR units. Over the years, a number of design improvements have been carried out in the 220 MWe Fuelling Machines to meet the challenge of increasing demands of higher refuelling rates. However, in 540 MWe unit, the average refuelling rate for an equilibrium core is nearly twice that of 220 MWe units. Apart from other assemblies in FM Head, the performance of Ram assembly plays a key role in meeting this demand. The experience of ballscrew ...

Energy Technology Data Exchange (ETDEWEB)

Three dimensional computational fluid dynamic (CFD) calculations of a typical prismatic very high temperature gas-cooled reactor (VHTR) were conducted to investigate the influence of gap geometry on flow and temperature distributions in the reactor core using commercial CFD code FLUENT. Parametric calculations changing the gap width in a whole core length model of fuel and reflector columns were performed. The simulations show the effects of core by-pass flows in the heated core region by comparing results for several gap widths including zero gap width. The calculation results underline the importance of considering inter-column gap width for the evaluation of maximum fuel temperatures and temperature gradients in fuel blocks. In addition, it is shown that temperatures of core outlet flow from gaps and channels are strongly affected by the gap width of by-pass flow in the reactor core.

Energy Technology Data Exchange (ETDEWEB)

Burner for feeding a solid and a liquid or gaseous fuel to a kiln comprises a central supply pipe for liquid or gas surrounded concentrically by a first pipe providing an annular passage through which primary air is supplied. Concentrically surrounding that pipe is a second pipe providing an annular channel for supply of solid fuel in carrier air stream. The outlet end of the first concentric pipe is closed by a plate fixed mounted at the pipe end and providing multiple nozzles having their axes parallel to the burner axis. The surface of the plate facing the burning zone provides a divergence opening for the central pipe while the inner surface is formed with helical teeth. These are engaged by complementary teeth mounted on the end of the central pipe which is rotatable and biased by springs so that the teeth are in engagement. Rotation of the pipe causes relative axial motion of the teeth to create tangential slots for admission of primary air into the central ...

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

This paper introduces a multichannel digital data acquisition system and examples of measurements with the system in seismic exploration using the high resolution seismic refraction method. The high resolution seismic refraction system performs analyses nearly automatically by using a computer after initial travel time has been read. Therefore, the system requires high-accuracy travel time data, for which a multichannel digital measuring instrument developed recently for seismic exploration using the refraction method has been used for the measurement. The specification specifies the number of channels at 144 as a maximum, a sampling time of 62.5 {mu}sec to 4 m sec, the maximum number of sampling of 80,000 samples, and gain accuracy of {plus_minus} 1%. The system was used for surveying a tunnel having a maximum soil cover of about 800 m. The traverse line length is about 6 km, the distance between vibration receiving points is 50 m, and the ...

International Nuclear Information System (INIS)

Two-phase air-water flows in a microscale fractal-like flow network were experimentally studied and results were compared to predictions from existing macroscale void fraction correlations and flow regime maps. Void fraction was assessed using (1) two-dimensional analysis of high-speed images (direct method) and (2) experimentally determined using gas velocities (indirect method). Fixed downstream-to-upstream length and width ratios of 1.4 and 0.71, respectively, characterize the five-level flow network. Channels were fabricated in a 38 mm diameter silicon disk, 250 ?m deep disk with a terminal channel width of 100 ?m. A Pyrex top allowed for flow visualization. Superficial air and water velocities through the various branch levels were varied from 0.007 m/s to 1.8 m/s and from 0.05 m/s to 0.42 m/s, respectively. Two-phase flow regime maps were generated for each level of the flow network and are well predicted by the ...

Energy Technology Data Exchange (ETDEWEB)

We investigated the electrical characteristics and the junction depth of ultra-shallow junctions formed by using the plasma-doping method. Compared with ultra-low energy boron-ion implantation at 500 eV, the junctions formed with the plasma-doping process exhibited shallow junction depths and low sheet resistances. The junction depths of the plasma-doped samples were 150 A and 330 A after annealing for 10 s at 900 .deg. C and 950 .deg. C, respectively. For the same junction depth, the sheet resistance of the B{sub 2}H{sub 6} plasma-doped sample was an order of magnitude less than that of the 500-eV B-ion implanted sample. Cross-sectional transmission electron microscopy and deep level transient spectroscopy showed that the defects formed by the B{sub 2}H{sub 6} plasma-doping process could be removed by annealing at 950 .deg. C for 10 s. The scaling of metal-oxide-semiconductor field-effect-transistor (MOSFET) device channel lengths for ...

Energy Technology Data Exchange (ETDEWEB)

Detecting a camouflaged target in a visually noisy background depends on the ability of the observer to discriminate the target from the surrounding terrain. Visible laser irradiation at less than damage levels can act as a masking source by compromising or reducing the observer's ability to resolve differences in the visual scene. Previous research has examined this concept by investigating laser flash effects on: acuity (size discrimination); tracking (motion discrimination); visual sensitivity (color); and contrast sensitivity functions (luminance contrast). In all cases, flashes from continuous-wave (CW) sources have proven more effective visually than pulsed (Q-switched) sources, when compared on peak-energy criteria (i.e., MPE), even though Q-switched lasers induce damage at lower energy doses. Additionally, the inherent safety of ultra-short laser pulses has been questioned. Past animal research has shown that, on the measures of acuity, ...

UK PubMed Central (United Kingdom)

Ion-channels can be activated (gated) by a variety of stimuli including chemicals, voltage, mechanical force or temperature. Whereas molecular mechanisms of ion-channel gating by chemicals and...Full Text Available

UK PubMed Central (United Kingdom)

Single-channel currents from acetylcholine receptor channels of garter snake neuromuscular junctions were recorded using the patch-clamp technique. Low concentrations of acetylcholine or carbamylcholine...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

In this study, the effects of channel surface wettability, cross-sectional geometry and orientation on the two-phase flow in parallel gas channels of proton exchange membrane fuel cells (PEMFCs) are investigated. Ex situ experiments were conducted in flow channels with three different surface wettability (hydrophilically coated, uncoated, and hydrophobically coated), three cross-sectional geometries (rectangular, sinusoidal and trapezoidal), and two orientations (vertical and horizontal). Flow pattern map, individual channel flow variation due to maldistribution, pressure drop and flow visualization images were used to analyze the two-phase flow characteristics. It is found that hydrophilically coated gas channels are advantageous over uncoated or slightly hydrophobic channels regarding un...

Energy Technology Data Exchange (ETDEWEB)

T{sub 2} weighted ultra-short turbo spin echo sequences were used in five individuals with variations in echo times, delayed triggering and echo intervals. To reduce movement artifacts all examinations were carried out with ECG and respiratory triggering. The sequences giving optimal image quality were then employed in 19 patients having various pulmonary abnormalities. Image resolutions, artifacts, image contrasts and diagnostic value were then judged by two observers and compared with CT. In the first study, a diastole-triggered UTSE sequence with the shortest echo proved optimal (T{sub E}=90 ms, T{sub R}=2-4 s, echo=9 ms, turbo factor=19). In the patient series studied, MRT was inferior to CT with regard to resolution and number of artifacts, but better in respect of contrast and diagnostic value. Using UTSE of the lung, MRT can produce images of good quality. Compared with CT, contrast is better with MRT, offering diagnostic advantages for MRT. (orig./MG) ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Conventional eddy current bobbin probes are known to be ineffectual in detecting circumferential cracks in tubing. Multi-pancake and/or rotating pancake probes are required to detect circumferential cracks. It has recently been demonstrated in CANDU steam generator tubes, with deformation, ferromagnetic deposits, and copper deposits, that multi-channel probes with transmit-receive (T/R) coils are superior to those using surface impedance coils. Unlike rotating probes, the design of a new probe denoted as C3 permits fast, single-scan inspection of a full-length tube at inspection speeds comparable to conventional bobbin probes. Since 1992, the probe has been used routinely for steam generator in-service inspection at 4 CANDU plants. Defective tubes have been plugged and the units returned to service, and they continue to operate without leaks. This paper describes the basic features of T/R surface probes. Two-dimensional voltage diagrams showing ...

Energy Technology Data Exchange (ETDEWEB)

This second report covers the period August 1 to September 30, 1991. During this period we modified our approach to Task 1 (Hybrid Armature study) with the addition of a numerical simulation of the steady state plasma brush length with a 1-D, four-phase equation of state code. A test fixture was designed and fabrication begun on a plasma brush test fixture for hybrid studies. It will be powered by a 140 kJ, 1 MA capacitor bank on loan to the project. Diagnostic data collection with 20 channels of digitizers and data reduction with a microvax were also arranged. Sliding friction of a solid armature was simulated and found to form a vapor layer at velocities below 2 km/s. The simulations indicated that higher interface pressure results in vapor boundary layer formation at lower velocity. If there is also a minimum interface pressure required to commutate high currents, then an optimum interface pressure will probably result. Plans for a launcher ...

Energy Technology Data Exchange (ETDEWEB)

A mesoscopically ordered lamellar gel phase of a polymer-grafted, lipid-based complex fluid is used as a scaffolding to spatially organize inorganic nanoparticles. The complex fluid provides both a highly anisotropic environment and a segregated aqueous and organic domains in which inorganic nanoparticles can be selectively placed by tailoring their size and surface characteristics. Three types of silver nanoparticles -- underivatized, surfactant-stabilized, and dodecanthiol-derivatized -- were evaluated. Comparison of the surface plasmon resonance of the various silver particles dispersed in conventional solvents to those contained within the complex fluid was used to determine the region of spatial localization in the lamellar gel phase. Silver particles rendered hydrophobic by capping with an alkane thiol insert into the hydrocarbon bilayer region. Surfactant-stabilized and underivatized silver nanoparticles reside in the aqueous channels, with the latter ...

Energy Technology Data Exchange (ETDEWEB)

The computer program is developed based on Visual C++, which is equipped with a user-friendly interface of the input/output(I/O) and a display function for the measuring conditions. This program consists of three parts which are the port communication, PLC(Programmable Logic Controller) and the MCA(Multi Channel Analyzer) control parts. The communication type between the CPU of the PLC module box and the computer is selected as be the Rs-232 asynchronous type and the thread method is adapted in the development of the first part of the program. The PLC-related program has been developed so that the data communication between the PLC CPU and the computer could be harmonized with the unique commands which have already been defined in the PLC. The measuring space and time intervals, the start and end ROI(region of interest) values, and the allowable error limitation are input at each measurement in this program. Finally the controlling MCA program has been developed by ...

International Nuclear Information System (INIS)

In this paper, a phenomenological model of the thermal hydraulics of convective boiling in the post-critical-heat-flux (post-CHF) regime is developed and discussed. The model was implemented in the TRAC-PF1/MOD2 computer code (an advanced best-estimate computer program written for the analysis of pressurized water reactor systems). The model was built around the determination of flow regimes downstream of the quench front. The regimes were determined from the flow-regime map suggested by Ishii and his coworkers. Heat transfer in the transition boiling region was formulated as a position-dependent model. The propagation of the CHF point was strongly dependent on the length of the transition boiling region. Wall-to-fluid film boiling heat transfer was considered to consist of two components: first, a wall-to-vapor convective heat-transfer portion and, second, a wall-to-liquid heat transfer representing near-wall effects. Each contribution was considered separately in ...

DEFF Research Database (Denmark)

Udgivelsesdato: 2002-May

Energy Technology Data Exchange (ETDEWEB)

To simulate the effects of the breakup channel on rearrangement amplitudes, the conventional coupled-reaction-channel (CRC) expansion is augmented by pseudoreaction channels. The construction of the projector for the extended CRC space is discussed, and transition-operator equations on this space are given. By solving the full and post-approximation forms of the CRC equations for a model three-particle problem, the crucial role played by the nonorthogonality terms is demonstrated.

Science.gov (United States)

Not Available

Science.gov (United States)

Not Available

International Nuclear Information System (INIS)

Short note.

Science.gov (United States)

Not Available

Science.gov (United States)

Not Available

DEFF Research Database (Denmark)

Udgivelsesdato: 2009

Science.gov (United States)

The local heat transfer coefficient distribution of a square channel with two opposite ribbed walls was determined. The square channel was connected to a sudden contraction entrance in order to simulate the inlet condition of the turbine blade cooling passages. The test channel was heated by thin stainless steel foils with a thickness of 0.000025 m, and instrumented with 180 thermocouples. The brass ribs of a square cross-section were glued periodically, in line, onto the top and bottom walls of the foil-heated channel in patterns to achieve the desired spacing and angle-of-attack. The local heat transfer coefficients on the smooth side and the ribbed side walls, at the channel entrance and the downstream regions, were measured for eight rib configurations and three Reynolds numbers (Re = 10,000, 30,000, and 60,000).

UK PubMed Central (United Kingdom)

This paper examines the utility of restriction fragment length polymorphisms (RFLPs) for paternity analysis. While, on the average, 99% of falsely accused males can be excluded with the standard battery...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Experimental investigation of heat transfer and friction factor characteristics of circular tube fitted with full-length helical screw element of different twist ratio, and helical screw inserts with spacer length 100, 200, 300 and 400mm have been studied with uniform heat flux under laminar flow condition. The experimental data obtained are verified with those obtained from plain tube published data. The effect of spacer length on heat transfer augmentation and friction factor, and the effect of twist ratio on heat transfer augmentation and friction factor have been presented separately. The decrease in Nusselt number for the helical twist with spacer length is within 10% for each subsequent 100mm increase in spacer length. The decrease in friction factor is nearly two times lower than the full length helical twist at low Reynolds number, and four times lower ...

UK PubMed Central (United Kingdom)

BackgroundLeukocyte telomere length (LTL) is an emerging marker of biological age. Chronic inflammatory activity is commonly proposed as a promoter of ...Full Text Available

UK PubMed Central (United Kingdom)

SUMMARYIn voltage-gated sodium, potassium, and calcium channels the functions of ion conduction and voltage sensing are performed by two distinct structural units: the pore domain...Full Text Available

UK PubMed Central (United Kingdom)

SummaryTRPV1 is the founding and best-studied member of the family of temperature-activated transient receptor potential ion channels (thermoTRPs). Voltage, chemicals, and heat...Full Text Available

UK PubMed Central (United Kingdom)

We have used the two-electrode voltage clamp technique and the patch clamp technique to investigate the regulation of ROMK1 channels by protein-tyrosine phosphatase (PTP) and protein-tyrosine...Full Text Available

UK PubMed Central (United Kingdom)

Searching for the structural requirements improving the potency and the stereoselectivity of Na⁺ channel blockers as antimyotonic agents, new...Full Text Available

UK PubMed Central (United Kingdom)

We analyze transport through conical channels due to the difference in particle concentration on the two sides of the membrane. Because of the detailed balance, fluxes of non-interacting particles...Full Text Available

UK PubMed Central (United Kingdom)

In voltage-gated Na⁺, K⁺, and Ca²⁺ channels, four voltage-sensor domains operate on a central pore domain in response to membrane voltage. In contrast, the voltage-gated...Full Text Available

CERN Document Server

Consider the simultaneous relay channel which consists of a set of relay channels where the source wishes to transmit common and private information to each of the destinations. This problem is recognized as being equivalent to that of sending common and private information to several destinations in presence of helper relays where each channel outcome becomes a branch of the broadcast relay channel (BRC). Cooperative schemes and capacity region for a set of two relay channels are investigated. The proposed coding schemes, based on Decode-and-Forward (DF) and Compress-and-Forward (CF), must be capable of transmitting information simultaneously to all destinations in such set. Inner bounds on the capacity region of the general BRC are based on three cases. First the channels from source-to-relays of both destinations are assumed to be stronger than the others and ...

UK PubMed Central (United Kingdom)

Recent studies suggest that calcium influx via L-type calcium channels is necessary for psychostimulant-induced behavioral sensitization. In addition, chronic amphetamine upregulates subtype...Full Text Available

UK PubMed Central (United Kingdom)

T-type calcium channels are responsible for generating low-threshold spikes that facilitate burst firing and neurotransmitter release in neurons. GnRH neurons exhibit burst firing, but the underlying...Full Text Available

CERN Document Server

This paper presents prefix codes which minimize various criteria constructed as a convex combination of maximum codeword length and average codeword length or maximum redundancy and average redundancy, including a convex combination of the average of an exponential function of the codeword length and the average redundancy. This framework encompasses as a special case several criteria previously investigated in the literature, while relations to universal coding is discussed. The coding algorithm derived is parametric resulting in re-adjusting the initial source probabilities via a weighted probability vector according to a merging rule. The level of desirable merging has implication in applications where the maximum codeword length is bounded.

Science.gov (United States)

... table (ASCAMP) system and the Military Strategic and Tactical Relay (Milstar) program. 10 ... Single Channel Antijam Milstar Portable Terminal ...

International Nuclear Information System (INIS)

... mixing coupled channel theory differential cross sections excited states helium

Science.gov (United States)

... measurement. Power spectral density measurements are made by the dynamic signal analyzer for each channel. A cross power ...

UK PubMed Central (United Kingdom)

Inhibition of large conductance calcium-activated potassium (BK_Ca) channels mediates, in part, oxygen sensing by carotid body type I cells. However, BK_Ca channels remain active...Full Text Available

CERN Document Server

A Multi-Channel Algebraic Scattering (MCAS) theory is presented with which the properties of a compound nucleus are found from a coupled-channel problem. The method defines both the bound states and resonances of the compound nucleus, even if the compound nucleus is particle unstable. All resonances of the system are found no matter how weak and/or narrow. Spectra of mass-7 nuclei and of {}^{15}F, and MCAS results for a radiative capture cross section are presented.

UK PubMed Central (United Kingdom)

Vacuolar ion channels in guard cells play important roles during stomatal movement and are regulated by many factors including Ca²⁺, calmodulin, protein kinases, and phosphatases....Full Text Available

International Nuclear Information System (INIS)

Planar channeling effects are studied in such well-oriented polycrystalline layers as NiSi_2 and Pb_2Si layers formed on single crystalline Si. Crystalline perfection of such layers is discussed by using the energy- and angular dependences of the axial and planar channeling yields. It has been shown that, in suitable conditions, the energy dependence of the planar yield is more sensitive to the spread of crystallite orientations in polycrystals than that of the axial one. (Auth.).

CERN Document Server

We consider a Josephson junction system installed with a finite length inhomogeneity, either of microresistor or of microresonator type. The system can be modelled by a sine-Gordon equation with a piecewise-constant function to represent the varying Josephson tunneling critical current. The existence of pinned fluxons depends on the length of the inhomogeneity, the variation in the Josephson tunneling critical current and the applied bias current. We establish that a system may either not be able to sustain a pinned fluxon, or - for instance by varying the length of the inhomogeneity - may exhibit various different types of pinned fluxons. Our stability analysis shows that changes of stability can only occur at critical points of the length of the inhomogeneity as a function of the (Hamiltonian) energy density inside the inhomogeneity - a relation we determine explicitly. In combination with ...

British Library Electronic Table of Contents (United Kingdom)

An experimental study was performed to investigate the heat transfer characteristics of the mixed convection flow through a horizontal rectangular channel where open-cell metal foams of different pore densities (10, 20 and 30 PPI) were situated. A uniform heat flux was applied at all of the bounding walls of the channel. For each of three values of the uniform heat flux, temperatures were measured on the entire surfaces of the walls. Results for the average and local Nusselt numbers are presented as functions of the Reynolds and Richardson numbers. The Reynolds number based on the channel height of the rectangular channel was varied from 600 to 33000, while the Richardson number ranged from 0.02 to 103, extending over forced, mixed and natural convection. Second important parameter that in...

British Library Electronic Table of Contents (United Kingdom)

Abstract Sudden infant death syndrome (SIDS) is always a devastating and unexpected occurrence. SIDS is the leading cause of death in the first 6 months after birth in the industrialized world. Since the discovery in 1998 of long QT syndrome as an underlying substrate for SIDS, around 10-20% of SIDS cases have been proposed as being caused by genetic variants in either ion channel or ion channel-associated proteins. Until now, 10 cardiac channelopathy susceptibility genes have been found to be implicated in the pathogenesis of SIDS. Four of the genes encode cardiac ion channel a-subunits, 3 genes encode ion channel b-subunits, and 3 genes encode other channel-interacting proteins. All 10 genes have been associated with primary electrical heart diseases. SIDS may hereby be the initial sympt...

International Nuclear Information System (INIS)

Previous flow regime studies have been for horizontal, vertical, and inclined pipe flow. As such, only a few studies have been performed on bundle geometries. The present paper examines the flow regimes for a vertical hexagonal flow channel with and without a finned fuel bundle. This type of a 36 finned rod hexagonal fuel bundle in parallel hexagonal flow channels is used in a MAPLE (Multi- purpose Applied Physics Lattice Experimental) type nuclear reactor. An experiment apparatus was designed consisting of the flow channel, inlet plenum and an air-water separator. The inlet plenum is used to provide a uniform mixture of air and water before entering the hexagonal flow channel. A turbine flow meter is used to determine the water flow rate. The turbine flow meter is calibrated for a low flow range and limits the measurable flow to 50 l/min. Flow pattern observation is determined by a SONY video camera, ...

Energy Technology Data Exchange (ETDEWEB)

Multi-dimensional modelling of two-phase flow requires accurate constitutive relationships for interfacial parameters such as interfacial heat transfer, void fraction distribution, interfacial area, etc. However, existing diagnostic systems for measurement of two-phase flow parameters have difficulty measuring two or three-dimensional void distributions required for determination of interfacial parameters. In this work, a Real-Time Neutron Radiography (RTNR) system is developed for non-intrusive measurement of two-phase flow parameters in nuclear fuel channels at low thermal neutron fluxes (on the order of 10{sup 6}n/cm{sup 2}-s). This advanced radiation technique has the advantage of measuring two-phase flow in 3 1/2 dimensions (x,{integral}dy,t) where the 1/2 dimension refers to an integrated or averaged space dimension. Pipe flow channels, annulus flow channels, MAPLE-type nuclear fuel flow channels, ...

Energy Technology Data Exchange (ETDEWEB)

Two-phase flow in horizontal parallel channels has been experimentally investigated under fuel cell related operating conditions. Pronounced hysteresis is observed in the pressure drop versus flow characteristic curve when starting from either flooded or dry conditions. When gas is introduced into channels initially filled with water (flooded initial condition), both gas and liquid tend to flow predominantly in one channel at low gas or liquid flow velocities. As the gas flow velocity increases, even distribution of gas and liquid flow in both channels is observed, accompanied with a sudden decrease in the pressure drop. On the other hand, even gas and liquid flow distribution between both channels is found at comparatively lower gas flow velocities when starting with dry-gas flow conditions with liquid introduced into channels filled with gas (stratified flow ...

Energy Technology Data Exchange (ETDEWEB)

Pipe whip tests or jet discharge tests have been performed at the Japan Atomic Energy Research Institute, which simulate the instantaneous guillotine break of primary coolant piping in nuclear power plants. This paper describes the results of the 4-inch pipe whip tests(RUN 5407, 5501, 5504, 5603), under the BWR LOCA conditions, which were performed from 1979 to 1981. The test pressure was 6.8 MPa and test temperature 285/sup 0/C. In these tests, clearance was kept constant at the value of 100 mm and overhang lengths were 250, 400, 550 and 1,000 mm, respectively. The main purpose of these tests is to investigate the effect of overhang length on pipe whip behavior. From the tests results, the pipe movement is effectively limited by the restraints if the overhang length is 250 mm or 400 mm. The deformation of the test pipe and restraints becomes large with increasing overhang length. It is clarified that ...

Energy Technology Data Exchange (ETDEWEB)

Poster session: Abstract is full text. Track membranes are thin polymer foils irradiated by heavy ions. The defects created by the heavy ions are located along the ions trajectory, the track. It is possible to open channels by etching with a chemical agent. These channels are very uniform. Small Angle Scattering (of X rays and neutrons) give global information about the characteristics of the channel shape. As the nanochannels are strictly parallel, an excellent sample orientation is required to obtain interpretable spectra. Then shoulders due to the oscillations of the Bessel function (radial part of the channel shape Fourier transform) are easily seen in the scattered intensity in the PXY data treatment software of SAS spectra allow to determine the channel diameter with its dispersion law, to demonstrate the existence of a wall thickness with a linearly varying density, and to ...

CERN Document Server

There are various interesting semantics' (extensions) designed for argumentation frameworks. They enable to assign a meaning, e.g., to odd-length cycles. Our main motivation is to transfer semantics' proposed by Baroni, Giacomin and Guida for argumetation frameworks with odd-length cycles to logic programs with odd-length cycles through default negation. The developed construction is even stronger. For a given logic program an argumentation framework is defined. The construction enables to transfer each semantics of the resulting argumentation framework to a semantics of the given logic program. Weak points of the construction are discussed and some future continuations of this approach are outlined.

Energy Technology Data Exchange (ETDEWEB)

An overview of particle and photon beam bunch length measurements is presented in the context of free-electron laser (FEL) challenges. Particle-beam peak current is a critical factor in obtaining adequate FEL gain for both oscillators and self-amplified spontaneous emission (SASE) devices. Since measurement of charge is a standard measurement, the bunch length becomes the key issue for ultrashort bunches. Both time-domain and frequency-domain techniques are presented in the context of using electromagnetic radiation over eight orders of magnitude in wavelength. In addition, the measurement of microbunching in a micropulse is addressed.

Energy Technology Data Exchange (ETDEWEB)

This document presents an assessment of the severe accident phenomena observed from four Full-Length High-Temperature (FLHT) tests that were performed by the Pacific Northwest Laboratory (PNL) in the National Research Universal (NRU) reactor at Chalk River, Ontario, Canada. These tests were conducted for the US Nuclear Regulatory Commission (NRC) as part of the Severe Accident Research Program. The objectives of the test were to simulate conditions and provide information on the behavior of full-length fuel rods during hypothetical, small-break, loss-of-coolant severe accidents, in commercial light water reactors.

International Nuclear Information System (INIS)

We estimate the optimum electric field at the sheath edge and the minimum interval among the nanotubes to promote the growth of armchair-type nanotubes (metallic character) as a function of the tube length. On the basis of the electric charge distribution in a nanotube and the optimum electric filed E*_1 at the tip of a nanotube evaluated using the Hueckel-Poisson method, we calculate the structure of the electric field lines outside a nanotube in the sheath region. As the tube length increases, the E*_1 decreases. To maintain the chemical activity at the tip, the sheath electric field must be decreased. We show the decreasing rate of the sheath field to the tube length.

International Nuclear Information System (INIS)

Heat transfer and flow characteristics of water boiling flow were experimentally investigated in narrow horizontal rectangular channels with the gaps of 0.6mm-2.03mm. The heat transfer of two-phase boiling flow was weakend in smaller gap. The two-phase friction pressure drop decreased with the gap size and the two-phase friction multipliers were smaller compared with those in normal channels. Correlations to predict te boiling heat transfer coefficients were obtained. (author)

Energy Technology Data Exchange (ETDEWEB)

A cooling system for rejecting waste heat consists of a cooling tower incorporating a plurality of coolant tubes provided with cooling fins and each having a plurality of cooling channels therein, means for directing a heat exchange fluid from the power plant through less than the total number of cooling channels to cool the heat exchange fluid under normal ambient temperature conditions, means for directing water through the remaining cooling channels whenever the ambient temperature rises above the temperature at which dry cooling of the heat exchange fluid is sufficient and means for cooling the water. 5 figs.

Energy Technology Data Exchange (ETDEWEB)

Cross sections for the elastic and inelastic scattering of /sup 16/O on /sup 58/Ni, /sup 88/Sr, /sup 40/Ca, and /sup 48/Ca have been calculated in a coupled-channels treatment, including the low-lying 2/sup +/ and 3/sup /minus// states of both projectile and target. Real, energy-independent ion-ion potentials and form factors were used, and fusion was simulated by ingoing wave boundary conditions in all channels. The agreement with the measured scattering data is qualitatively as good as obtained in previous optical-model calculations.

KoreaScience (Korea)

Full Text Available

UK PubMed Central (United Kingdom)

The muscles of three different arthropods, a mite, a fly, and an ostracod, show variations in the length of the A region within a given individual. There is no indication that the observed differences...Full Text Available

Science.gov (United States)

... Wheeled Vehicle) equipped with a MILSTAR terminal was driven ... textbooks including Ronald W. Wolff, Stochastic Modeling and The ... Queue Length ...

Energy Technology Data Exchange (ETDEWEB)

Design of pipe whip restraints requires a knowledge of the maximum allowable unsupported pipe length. This paper presents a numerical method for calculating this critical length of the pipe. Salient features of the method are: (1) as a flow rounds an elbow, it exerts a transverse kick and an axial thrust to the pipe, both the axial thrust and the bending moment are considered; (2) the jet force is applied in an abrupt manner, the dynamic amplification factor (DAF) is determined from the load-deflection (H-{Delta}) curve of the pipe, by taking into consideration large strain, large deformation and the nonlinear stress-strain relationship of the piping material; (3) the ultimate capacity of the pipe under the combined action of an axial force and a bending moment is governed by an interaction formula. The maximum unsupported pipe length is calculated from this formula. Only the formulas and derivation are presented. Numerical ...

Science.gov (United States)

... We use a compliant, sealed tube helically wrapped with an optical fiber. ... 2.5 cm diameter compliant, sealed tube 10 m < length < 120 m ...

Energy Technology Data Exchange (ETDEWEB)

Carbon dioxide is receiving renewed interest as an efficient and environmentally safe refrigerant in a number of applications, including mobile air conditioning and heat pump systems, and hot water heat pumps. Compact heat exchangers for CO{sub 2} systems are designed with small-diameter tubing. The purpose of this study is therefore to provide a better basis for understanding and predicting heat transfer and pressure drop during flow vaporization of CO{sub 2} in microchannels. The ''unusual'' properties of carbon dioxide give heat transfer and two-phase flow characteristics that are very different from those of conventional refrigerants. Examples of these differences are the much higher pressure, the resulting high vapour density, a very low surface tension, and a low liquid viscosity. High pressure and low surface tension has a major effect on nucleate boiling characteristics, and earlier test data have shown a clear dominance of nucleate boiling ...

CERN Document Server

This paper focuses on the analysis of average Gaussian error probabilities in certain fading channels, i.e. we are interested in E[Q((p {\\gamma})^(1/2))] where Q(.) is the Gaussian Q-function, p is a positive real number and {\\gamma} is a nonnegative random variable. We present a unified analysis of the average Gaussian error probability, derive a compact expression in terms of the Lauricella FD^(n) function that is applicable to a broad class of fading channels, and discuss the relation of this expression and expressions of this type recently appeared in literature. As an intermediate step in our derivations, we also obtain a compact expression for the outage probability of the same class of fading channels. Finally, we show how this unified analysis allows us to obtain novel performance analytical results.

International Nuclear Information System (INIS)

The ROP margin in a CANDU reactor is decreasing over time due to the Primary Heat-Transport System (PHTS) aging effect. Adjustment of the ROP trip setpoint is required to maintain a high trip-probability and ROP trip effectiveness. Especially, for Wolsong-1, which is scheduled to change the old pressure tubes in 2009, the trend of ROPT after the retubing should be reevaluated. Before setting a ROPT, the main thermal characteristics including Critical Channel Power (CCP) should be calculated by the NUCIRC code. In this paper, the thermalhydraulic evaluation for Wolsung-1 was conducted with the updated Wolsung-1 PHTS data. Specifically, for the case of 0 EFPY (Effective Full Power Year) and 11 EFPY after the retubing, the distribution of the channel flow rate, channel exit quality, critical channel power, and critical power ratio (CPR) of the Wolsong-1 aged plant are calculated

International Nuclear Information System (INIS)

For the determination of the thermal-hydraulic performances of rough surfaces, the method of evaluation is particularly important. In order to increase confidence in the results, a new evaluation procedure was introduced. This procedure is based on the transformation of simple channel experimental results to equal boundary conditions, and on the suitable application and confirmation of these transformed values in more complicated flow channel geometries. Existing methods, applied to the results obtained in an annular channel, do not fulfil all the transformation requirements. Thus a new, more complete transformation method, which uses the turbulent eddy diffusivity model, was developed. To check the quality of this transformation, within the scope of the new evaluation procedure, the results of experimental investigation in annular channels and in a bundle of hexagonal geometry were used together with ...

Science.gov (United States)

We present a quantum secure direct communication scheme achieved by swapping quantum entanglement. In this scheme a set of ordered Einstein-Podolsky-Rosen (EPR) pairs is used as a quantum information channel for sending secret messages directly. After insuring the safety of the quantum channel, the sender Alice encodes the secret messages directly by applying a series local operations on her particle sequences according to their stipulation. Using three EPR pairs, three bits of secret classical information can be faithfully transmitted from Alice to remote Bob without revealing any information to a potential eavesdropper. By both Alice and Bob's GHZ state measurement results, Bob is able to read out the encoded secret messages directly. The protocol is completely secure if perfect quantum channel is used, because there is not a transmission of the qubits carrying the secret message between Alice and Bob in the public ...

Energy Technology Data Exchange (ETDEWEB)

This report describes all time and frequency analysis parameters measured with the new Nuclear Weapons Identification System (NWIS) processor with three input channels: (1) the 252Cf source ionization chamber (2) a detection channel; and (3) a second detection channel for active measurements. An intuitive and physical description of the various functions is given as well as a brief mathematical description and a brief description of how the data are acquired. If the fill five channel capability is used, the number of functions increases in number but not in type. The parameters provided by this new NWIS processor can be divided into two general classes: time analysis signatures including multiplicities and frequency analysis signatures. Data from measurements with an 18.75 kg highly enriched uranium (93.2 wt 0/0, 235U) metai casting for storage are presented to illustrate the various time and frequency ...

British Library Electronic Table of Contents (United Kingdom)

In today's maturing consumer markets, emphasis is shifting from straightforward sales to a more holistic approach to customer life cycle management, with a stronger emphasis on how sales are generated and service provided all along the customer journey. Effectively managing these different marketing, sales and service channels poses a significant challenge. Companies need new strategies, structures, processes and tools to deliver customer value across all channels. A multi-channel, integrative customer model that delivers customer value and significant return on investment (ROI) requires both a strong understanding of customer preferences and behaviours and a robust IT architecture that supports the overarching customer relationship management (CRM) strategy. Even those organizations that ...

UK PubMed Central (United Kingdom)

Congestive heart failure (CHF) is a leading cause of morbidity and mortality. CHF is marked by atrial and ventricular enlargement and reduced cardiac contractility, as well as an association...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Information technology allows national and local governments to satisfy the needs of citizens in a cost effective way. Unfortunately, citizens still tend to prefer traditional, more costly channels, such as the front desk, phone and mail. Through pilot projects government agencies attempt to influence this behavior of citizens, directing them towards the online channel. With this paper we provide insight into the possibility to influence citizens' behavior in the complex landscape of multi-channel service provision. The paper systematically compares five pilot projects using a framework that is based on organizational and marketing literature. The results show that socio-psychological factors are crucial in multi-channel management, much more than the technology itself. We conclude that ci...

Science.gov (United States)

of a stochastic network can be a. PERT-type network. After the terminal countdown, ...... pictorial representation of a single channel queueing system ...

British Library Electronic Table of Contents (United Kingdom)

Mixed convection heat transfer from longitudinal fins inside a horizontal channel has been investigated for a wide range of modified Rayleigh numbers and different fin heights and spacings. An experimental parametric study was made to investigate effects of fin spacing, fin height and magnitude of heat flux on mixed convection heat transfer from rectangular fin arrays heated from below in a horizontal channel. The optimum fin spacing to obtain maximum heat transfer has also been investigated. During the experiments constant heat flux boundary condition was realized and air was used as the working fluid. The velocity of fluid entering channel was kept nearly constant (0.15win0.16m/s) using a flow rate control valve so that Reynolds number was always about Re=1500. Experiments were conducted...

Science.gov (United States)

... time. The Paleozoic Era ended only 248 million years ago, the Mesozoic Era ended only 65 million years ago, and so on. ...

International Nuclear Information System (INIS)

During the last two decades, the demand for higher heat transfers in the heat exchangers has kept increasing. These high heat transfer rates can be obtained by using two-phase flows, or heat transfer augmented surfaces, or in some cases, both. Thus, the boiling flows and the associated two-phase flow instabilities have been studied by many investigators. Most of the work in boiling flows has been concentrated on single channel upflow systems or on parallel channel systems with plain heat transfer surfaces. The boiling flow instabilities in multi-channel systems should be covered to a greater extent, studying the effects of various parameters, such as inlet and outlet restriction, mass flow rates, the property variations, heat transfer coefficients, equal and unequal heat inputs on the stability. Also, the mathematical modeling needs to be developed for the parallel channel system to take into account ...

CERN Document Server

We consider a multiple-input multiple-output (MIMO) multiple access channel (MAC), where the channel between each transmitter and the receiver is modeled by the doubly-scattering channel model. Based on novel techniques from random matrix theory, we derive deterministic approximations of the mutual information, the signal-to-noise-plus-interference-ratio (SINR) at the output of the minimum-mean-square-error (MMSE) detector and the sum-rate with MMSE detection which are almost surely tight in the large system limit. Moreover, we derive the asymptotically optimal transmit covariance matrices. Our simulation results show that the asymptotic analysis provides very close approximations for realistic system dimensions.

International Nuclear Information System (INIS)

A two-phase flow regime map is developed experimentally and theoretically for a vertical hexagonal flow channel with and without a 36-finned rod hexagonal bundle. This type of flow channel is of interest to MAPLE-type nuclear research reactors. The flow regime maps are determined by visual observations and observation of waveforms shown by a capacitance-type void fraction meter. The experimental results show that the inclusion of the finned hexagonal bundle shifts the flow regime transition boundaries toward higher water flow rates. Existing flow regime maps based on pipe flow require slight modifications when applied to the hexagonal flow channel with and without a MAPLE-type finned hexagonal bundle. The proposed theoretical model agrees well with experimental results.

Science.gov (United States)

A comparison of benthic biodiversity in the North Sea, English Channel, and Celtic Seas. ICES J. Mar. Sci./J. Cons. int. Explor. Mer 56: 228-246. ...

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: The heat transfer and flow in narrow channels has lots of advantages such as compact structure, high efficiency, design flexibility and so on. So it is widely used in the fields such as the new reactor core plate elements, the once-through stream generator, compact heat exchangers as well as electronic components. In recent years, more strong attentions have been attracted to the thermal-hydraulic characteristics and mechanism of the two-phase flow in narrow channels. As the flow regime characteristics of two-phase flow is fundamental one of them, the research on the two-phase flow regimes and the regime transitions in horizontal rectangular narrow heated channels can provide theoretical foundation and engineering directions to the whole research on the thermal-hydraulic characteristics and mechanism of the two-phase flow in narrow channels. The characteristics of ...

Energy Technology Data Exchange (ETDEWEB)

The strain gradient crystal plasticity theory is applied to study the deformation of planar single crystal with a void under a nominally uniaxial tension. The crystal theory assumes elevated strain hardening due to slip gradients and has a constitutive length scale. The effects of the void size with respect to the constitutive length scale on the single crystal deformation are investigated.

UK PubMed Central (United Kingdom)

Okayama and Berg (1) have recently described a technique for the high efficiency cloning of full-length dscDNAs. We have constructed eukaryotic expression vectors compatible both with this technique...Full Text Available

UK PubMed Central (United Kingdom)

Four new mutants are described whose phenotypic expression affects the length of the head of bacteriophage T4D. All mutants produce some phenotypically normal phage particles. Mutant pt21-34...Full Text Available

International Nuclear Information System (INIS)

A possibility is considered or reducing the surface heterogeneity effect of an item being tested on the result of radiation flaw detection by means of signal delay of one of detectors in a two-channel radiometric flaw detector. The exposure of a translationally moving item has been studied as well as an external exposure of a rotating hollow item.

International Nuclear Information System (INIS)

A series of real-time, neutron radiography, experiments are ongoing at the Texas A and M Nuclear Science Center Reactor (NSCR). These tests determine the resolving capabilities for radiographic imaging of two phase water and air flow regimes through small diameter flow channels. Though both film and video radiographic imaging is available, the real-time video imaging was selected to capture the dynamic flow patterns with results that continue to improve. (author)

International Nuclear Information System (INIS)

A new type of multi-channel analyzer system is introduced, which takes advantage of Universal Serial Bus to communicate with computer and gets the merit of fast speed, universality and Plug and Play. The authors discussed the framework of the system, primary functions, display of spectrum date and the way of communication with hardware. The environment of the program is Visual Basic 6.0

UK PubMed Central (United Kingdom)

Airway ciliated cells express an ATP-gated P2X receptor channel of unknown subunit composition (P2X_cilia) which is modulated by Na⁺ and by long exposures to ATP. P2X_cilia...Full Text Available

Science.gov (United States)

The mz8310 device support module provides support for the following record types: event, pulseCounter, pulseDelay, and pulseTrain. No driver support is needed. Up to 4 mz8310 modules are supported. Each 8310 module contains 10 channels, which are identified as signals O,...9. Each channel is individually configurable. Each mz83 10 has two Am9513 Timing Controller chips. Each Am9513 has 5 counters.

Energy Technology Data Exchange (ETDEWEB)

The theoretical treatment of the relation between the critical angle of planar channeling and the characteristics of crystal lattice defects is carried out. The predictions are made about some typical forms of the critical angle dependence on the mean-square static displacement produced by defects, and then these predictions are detailed for the cases of homogeneous disordering, spherical clusters of point defects and dislocation loops. Analytical results are supported by the exact computer calculations for the defects in the intermetallic A-15 compounds.

International Nuclear Information System (INIS)

The case of spontaneous radiation of channeled ultrarelativistic particles is considered when the dipolarity condition is not satisfied. The change of the particle longitudinal velocity affecting the maximum radiation frequency is included. The angular and frequency characteristics of the radiation for superhigh energies are studied for the first time. It is shown that there is an optimum energy at which the radiation density is maximum. The influence of the angle at which electrons enter a crystal and of the beam divergence on the radiation is investigated. The problem of quasichanneled particle radiation and also the radiation in axis-plane transitions are considered. (author).

CERN Document Server

We present the initial results of an observational study into the variation of the dominant length-scale of quiet solar emission: supergranulation. This length-scale reflects the radiative energy in the plasma of the upper solar chromosphere and transition region at the magnetic network boundaries forming as a result of the relentless interaction of magnetic fields and convective motions of the Sun's interior. We demonstrate that a net difference of ~0.5Mm in the supergranular emission length-scale occurs when comparing observations cycle 22/23 and cycle 23/24 minima. This variation in scale is reproduced in the datasets of multiple space- and ground-based instruments and using different diagnostic measures. By means of extension, we consider the variation of the supergranular length-scale over multiple solar minima by analyzing a subset of the Mt Wilson Solar Observatory (MWO) Ca II K image record. The ...

Energy Technology Data Exchange (ETDEWEB)

With using artificial neural networks (ANNs), an analytical study related to the heated length effect on critical heat flux (CHF) has been carried out to make an improvement of the CHF prediction accuracy based on local condition correlations or table. It has been carried out to suggest a feasible criterion of the threshold length-to-diameter (L/D) value in which heated length could affect CHF. And within the criterion, a L/D correction factor has been developed through conventional regression. In order to validate the developed L/D correction factor, CHF experiments for various heated lengths have been carried out under low and intermediate pressure conditions. The developed threshold L/D correlation provides a new feasible criterion of L/D threshold value. The developed correction factor gives a reasonable accuracy for the original database, showing the error of -2.18% for average and 27.75% for RMS, ...

CERN Document Server

Inter-symbol interference (ISI) channels with data dependent Gauss Markov noise have been used to model read channels in magnetic recording and other data storage systems. The Viterbi algorithm can be adapted for performing maximum likelihood sequence detection in such channels. However, the problem of finding an analytical upper bound on the bit error rate of the Viterbi detector in this case has not been fully investigated. Current techniques rely on an exhaustive enumeration of short error events and determine the BER using a union bound. In this work, we consider a subset of the class of ISI channels with data dependent Gauss-Markov noise. We derive an upper bound on the pairwise error probability (PEP) between the transmitted bit sequence and the decoded bit sequence that can be expressed as a product of functions depending on current and previous states in the (incorrect) decoded sequence and the ...

International Nuclear Information System (INIS)

An attempt was made to minimize the channeling tail by implantation along a random equivalent direction following a careful alignment of the target. In order to analytically determine the random equivalent directions, critical angles for channeling were mapped on a stereogram. Boron ions with energies of 17 and 45 keV are implanted along specified directions determined from the map. The depth distribution of the dopant is profiled by SIMS and the effects of water orientation upon the channeling tail are noted. Industrial common use of a 7"0 tilt is not optimum. However, implantation with the wafer tilted at 5.5 +/- 0.5"0 from the surface normal and rotated at 7.0 +/- 0.5"0 from a (100) plane shows the least channel-tail compared to implantation along other directions. Rapid thermal annealing (RTA) is a promising annealing method for shallow junction formation. Transient enhanced diffusion of implanted ...

CERN Document Server

In this paper, we consider a $n_t\\times n_r$ multiple-input multiple-output (MIMO) channel subjected to block fading. Reliability (in terms of achieved diversity order) and rate (in number of symbols transmitted per channel use) are of interest in such channels. We propose a new precoding scheme which achieves both full diversity ($n_tn_r$th order diversity) as well as full rate ($n_t$ symbols per channel use) using partial channel state information at the transmitter (CSIT), applicable in MIMO systems including $n_r

CERN Document Server

The front-end electronics system for the anode signals of the CMS Endcap Muon cathode strip chambers has about 183000 channels. The purposes of the anode front-end electronics are to acquire precise muon timing information for bunch crossing number identification at the Level-1 muon trigger system and to provide a coarse radial position of the muon track. Each anode channel consists of an input protection network, amplifier, shaper, constant-fraction discriminator, and a programmable delay. The essential parts of the electronics include a 16-channel amplifier-shaper-discriminator ASIC CMP16 and a 16-channel ASIC D16G providing programmable time delay. The ASIC CMP16 was optimized for the large cathode chamber size (up to 3 x 2.5 m2) and for the large input capacitance (up to 200 pf). The ASIC combines low power consumption (30 mW/channel) with good time resolution (2 - 3 ns). The ...

Energy Technology Data Exchange (ETDEWEB)

Some diagnostics at the National Ignition Facility (NIF), including the Gamma Reaction History (GRH) diagnostic, require multiple channels of data to achieve the required dynamic range. These channels need to be stitched together into a single time series, and they may have non-uniform and redundant time samples. We chose to apply the popular cubic smoothing spline technique to our stitching problem because we needed a general non-parametric method. We adapted one of the algorithms in the literature, by Hutchinson and deHoog, to our needs. The modified algorithm and the resulting code perform a cubic smoothing spline fit to multiple data channels with redundant time samples and missing data points. The data channels can have different, time-varying, zero-mean white noise characteristics. The method we employ automatically determines an optimal smoothing level by minimizing the Generalized Cross ...

International Nuclear Information System (INIS)

Recently a new method of controlling the pulse length of a short-pulse free-electron laser (FEL) has been developed. By modulating the synchronism between the optical and electron pulses in the FEL cavity, it was found that the output power and the micropulse length of the FEL beam oscillates at the modulation frequency. In this paper, we study theoretically the behavior of the micropulse length, both in the high loss (steady state) regime and the low loss (limit cycle) regime, when a modulated desynchronism is applied. In order to do this, we analyze the dynamics of a short-pulse FEL oscillator. The modulation frequency value plays an important role in the dynamics. We find that there is a resonantlike phenomenon between the externally applied desynchronism modulation and the limit cycle oscillation without modulation of a free-electron laser.

British Library Electronic Table of Contents (United Kingdom)

Summary CAG trinucleotide repeat length in the nuclear polymerase gamma gene (POLg) has been shown to be associated with men with reduced fertility. The present study investigated the frequency of CAG repeat length genotypes and three exonuclease motifs of the POLg in relation to the frequency of mitochondrial nucleotide substitutions. DNA from semen samples of 93 normozoospermic men and 192 non-normozoospermic men was isolated and the specific regions of the genes were amplified by polymerase chain reactions (PCR) and sequenced to identify mutations. The genotypic frequencies of pooled POLg CAG repeat lengths, =10/!=10 heterozygotes and !=10/!=10 homozygotes, were significantly different between normozoospermic and non-normozoospermic men (p p POLg genotype. Of the 17 men with non-synonym...

Energy Technology Data Exchange (ETDEWEB)

Methods for improving the sensitivity of scintillation cells for radon concentration measurements were studied with emphasis on improving light collection efficiency. This allows the length and hence the volume of the cell to be increased. Variables studied were choice of scintillator material, its method of application and thickness, length of cell, cell material, type and configuration of reflectors, choice of photomultipliers, and factors affecting background. Response from various areas of the cell surface was studied with an alpha source and with radon filling. Coating the window with phosphor was found to be counter-productive. The optimum results obtained were with the inside of the cell (other than the window) covered with a thick layer of ZnS(Ag), or with a thick layer of reflective material coated with a thin layer of phosphor. With it, a 10 cm diameter plexiglass cell can be extended to at least 50 cm length ...

Energy Technology Data Exchange (ETDEWEB)

This paper considers the physical and mechanical properties of rocks (volumetric density, angle of repose, lump size, abrasive strength, etc.), and their influence on choice of belt conveyors for overburden haulage. Technological parameters (length and output of benches, coefficient of utilization and reliability of equipment, investment cost, etc.) are also considered. Data are given on the capacity and length of conveyors widely used in coal surface mining (width up to 3,000 mm, speed up to 6 m/s and capacity 24,000-35,000 t/h at lengths of 1,400-3,000 m). (12 refs.) (In Serbo-Croat)

British Library Electronic Table of Contents (United Kingdom)

Objectives To investigate the feasibility and reproducibility of measurements of nasal bone length using a three-dimensional (3D) ultrasound in the first trimester. Methods In a prospective study, 118 consecutive pregnant women attending for Down syndrome screening at 11-13 + 6 weeks were recruited. They had successful fetal nasal bone measurement by two-dimensional (2D) ultrasound by four operators. Three-dimensional volumes were recorded in the mid-sagittal plane of fetal profile by the fifth operator and examined using multiplanar techniques. Another independent investigator randomly compared his measurements with one of the four operators. Results In the subsequent 3D examination, the nasal bone length could be examined in 94 cases (79.7%). The mean difference between the 2D and 3D mea...

CERN Document Server

Assuming the hoop conjecture in classical general relativity and quantum mechanics, any observer who attempts to perform an experiment in an arbitrarily small region will be stymied by the formation of a black hole within the spatial domain of the experiment. This behavior is often invoked in arguments for a fundamental minimum length. Extending a proof of the hoop conjecture for spherical symmetry to include higher curvature terms we investigate this minimum length argument when the gravitational couplings run with energy in the manner predicted by asymptotically safe gravity. We show that argument for the mandatory formation of a black hole within the domain of an experiment fails. Neither is there a proof that a black hole doesn't form. Instead, whether or not an observer can perform measurements in arbitrarily small regions depends on the specific numerical values of the couplings near the UV fixed point. We further argue that when an ...

Science.gov (United States)

Turbulent flow in a 2D channel with repeated rectangular rib roughness was numerically simulated using a low Reynolds number form of the k-epsilon turbulence model. Friction factors and average Stanton numbers were calculated for various pitch to rib height ratios and bulk Reynolds numbers. Comparisons with experiment were generally adequate, with the predictions of friction superior to those for heat transfer. The effect of variable properties for channel flow was investigated, and the results showed a greater effect for friction than for heat transfer. Comparison with experiment yielded no clear conclusions. The turbulence model was also validated for a related problem, that of flow downstream of an abrupt pipe expansion.

CERN Document Server

In pp collisions at 1.25 GeV kinetic energy, the HADES collaboration aimed at investigating the di-electron production related to $\\Delta$ (1232) Dalitz decay ($\\Delta^+ \\to pe^+e^-$). In order to constrain the models predicting the cross section and the production mechanisms of $\\Delta$ resonance, the hadronic channels have been measured and studied in parallel to the leptonic channels. The analyses of $pp\\to np\\pi^+$ and $pp\\to pp\\pi^0$ channels and the comparison to simulations are presented in this contribution, in particular the angular distributions being sensitive to $\\Delta$ production and decay. The accurate acceptance corrections have been performed as well, which could be tested in all the phase space region thanks to the high statistic data. These analyses result in an overall agreement with the one-$\\pi$ exchange model and previous data.

International Nuclear Information System (INIS)

The influence of hydrogen ion implantation into the channel polysilicon of polysilicon thin film transistors on gate oxide conductivity has been investigated. Data for effective tunnelling barriers at the gate oxide/channel polysilicon interface are presented. A value of 1.2eV for samples with boron doped channel polysilicon is calculated. For hydrogenated boron doped samples tunnelling barriers higher than 2.1 eV are obtained. The tunnelling barriers for phosphorus doped samples are impurity concentration dependent and decrease with increasing phosphorus concentration in the range 3 x 10"1"7 to 3 x 10"1"9 cm"-"3. (Author).

British Library Electronic Table of Contents (United Kingdom)

This study aimed to explore the impact of perceived service quality and self-concept on consumer attitude and purchase process using channel type (physical and Internet) as a segmentation variable. From the perspective of consumer behaviour, this study attempted to estimate a relational model and perform an empirical validation using female cosmetics and skincare products as an example. It was discovered that the influence of perceived service quality and self-concept on consumer attitude, purchase intention and behaviour, satisfaction, and loyalty varied with channel type. The analysis result revealed that physical stores presented higher levels of agreement with all research perspectives than Internet stores. However, only two relational paths have a higher influencing effect in physical...

Science.gov (United States)

Mixed convection in a rectangular channel (width/height = 2) with bottom-heated and top-cooled sections is studied by laser Doppler anemometry in nitrogen at Ra = 22,200 and Re = 18.75, 36, and 54. At the lower Re values, symmetry breaking is observed in steady but spatially oscillating flows that prevail over a certain distance from the leading edge of the differentially heated section. Further downstream, unsteady flows are found even for Re = 18.75. Numerical models are used to investigate the effects of adiabatic, conducting (with a conductive-convective heat transfer coefficient), and perfectly conducting side walls; channel tilts and Prandtl number dependence. Good agreement between calculations and experiment is obtained for longitudinal convective roll velocities. The transverse velocities are found to be independent of Re.

International Nuclear Information System (INIS)

Mass transfer to a wall of a horizontal rectangular channel reactor was investigated by the limiting current technique for Reynolds numbers ranging from 200 to 32000. Overall mass transfer coefficients at various mass transfer surface angles were obtained while the reactor was operated under isothermal and non-isothermal conditions. Dimensionless correlations were developed for isothermal flows from 25 to 55"oC and for non-isothermal flows with applied temperature differences up to 30"oC. In the laminar flow range natural convection dominated, but under turbulent conditions combined natural and forced convection prevailed. Mass transfer was approximately doubled under optimum selection of channel surface rotation, temperature gradient and flow rate. (author)

British Library Electronic Table of Contents (United Kingdom)

BACKGROUND AND PURPOSE Controlling vascular tone involves K+ efflux through endothelial cell small- and intermediate-conductance calcium-activated potassium channels (KCa2.3 and KCa3.1, respectively). We investigated the expression of these channels in astrocytes and the possibility that, by a similar mechanism, they might contribute to neurovascular coupling. EXPERIMENTAL APPROACH Transgenic mice expressing enhanced green fluorescent protein (eGFP) in astrocytes were used to assess KCa2.3 and KCa3.1 expression by immunohistochemistry and RT-PCR. KCa currents in eGFP-positive astrocytes were determined in situ using whole-cell patch clamp electrophysiology. The contribution of KCa3.1 to neurovascular coupling was investigated in pharmacological experiments using electrical field stimulatio...

British Library Electronic Table of Contents (United Kingdom)

Riparian zones of streams in northwestern Mississippi have been impacted by agriculture, channelization, channel incision, and gully erosion. Riparian gully formation has resulted in the fragmentation of remnant riparian zones within agricultural watersheds. One widely used conservation practice for controlling gully erosion is the installation of drop pipes. This practice involves placing earthen dams across eroding gullies and embedding a metal standpipe within the dam to convey water from the field to stream level. Installation of this structure halts gully erosion and incidentally replaces eroding gullies with riparian habitats. Previous research evaluating gully erosion control structures have not considered the ecological impacts of these conservation practices on amphibian and repti...

International Nuclear Information System (INIS)

The loss of seal of the H9 channel in vacuum, freeing the entire cross section of the front part, leads to a fast leak that progresses rapidly. The effect of depressurizing the reflector can leads to shutdown of the shutdown rod pumps. The source changer associated with the channel fills completely before the valve closes. All of the leak water remains contained within the source changer containment. After the valves open, cooling of the fuel element is handled by natural convection, requiring a reversal of the flow between the plates. This changeover, which takes place at a relatively low pressure level, could lead to local boiling in the fuel element. Consequently, irreversible transformations cannot be excluded as possibilities for the fuel element and even for the control rod. Subsequently, the can is refilled with heavy water with establishment of the usual pressure levels.

British Library Electronic Table of Contents (United Kingdom)

To form a licensing basis for a new methodology for a fuel channel safety analysis code for CANDU-6 nuclear reactor, a CATHENA model for a post-blowdown fuel channel analysis has been developed, and tested for a high temperature thermal-chemical experiment CS28-1 [Lei, Q.M., 1993. Post-test analysis of the 28-element high-temperature thermal-chemical experiment CS28-1. In: 4th International Conference on Simulation Methods in Nuclear Engineering, Montreal, PQ, 1993]. Pursuant to the objective of this investigation, the current study has focused on understanding the involved phenomena, their interrelations, and how to maintain a good accuracy of the temperature and H2 generation rate prediction without losing the important physics of the involved phenomena. The transient simulation results ...

International Nuclear Information System (INIS)

Using a realistic three-body model, angular distributions for the "1"6O(d,p)"1"7O(1/2"+) reaction, based on the channel coupling array (CCA) theory and various forms of the coupled reaction channel (CRC) method are compared. Despite the different forms and theoretical foundations of these methods, they yield similar angular distributions, within the bound state approximations used herein. The expected breaking of time reversal inveriance in the approximated CCA theory is quite small over most of the angular range. Of all the methods used, coupling effects in the forward directions are largest for the post form of the CRC, indicating that it is the least reliable of the CRC forms for fitting data. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

Various measurement tools that are used in chaos theory were applied to analyze two-phase pressure signals with the objective of identifying and interpreting flow pattern transitions for two-phase flows in a small, horizontal rectangular channel. These measurement tools included power spectral density function, autocorrelation function, pseudo-phase-plane trajectory, Lyapunov exponent,s and fractal dimensions. It was demonstrated that the randomlike pressure fluctuations characteristic of two-phase flow in small rectangular channels are chaotic, and governed by a high-order deterministic system. The correlation dimension is potentially a new approach for identifying certain two-phase flow patterns and transitions.

UK PubMed Central (United Kingdom)

The genome sequence of the Mamavirus, a new Acanthamoeba polyphaga mimivirus strain, is reported. With 1,191,693 nt in length and 1,023 predicted protein-coding genes, the Mamavirus...Full Text Available

Science.gov (United States)

... feet in length, and 26 feet 2 inches high. The AC-119G and AC-119K, are powered with two General Electric J85-17 jet engines pod-mounted ...

Science.gov (United States)

C-130J payload reduced to make radius. ** Current C-17A uses 3000 ft field, C- 17A+ estimated cost of $378M per plane with. 2000 ft field length, ...

UK PubMed Central (United Kingdom)

Somatic embryogenesis (SE) is the developmental restructuring of somatic cells towards the embryogenic pathway and forms the basis of cellular totipotency in angiosperms. With the availability of full-length...Full Text Available

UK PubMed Central (United Kingdom)

PurposeA prolonged seizure, status epileptics (SE), is a potent stimulus for increased neurogenesis in the dentate gyrus of the hippocampus. Molecular mechanisms...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The coking plant is described with some details of coal supplies and coke quality. Engineering improvements to the by-product system and coke oven machines, major repair of two batteries, installation of a PLC-based monitoring and control system, and training of personnel are dealt with at greater length.

UK PubMed Central (United Kingdom)

BackgroundBaculovirus, which has a width of 40 nm and a length of 250-300 nm, can display functional peptides, receptors and antigens on its surface by their fusion with a baculovirus...Full Text Available

UK PubMed Central (United Kingdom)

To delineate the mechanisms of bovine leukemia virus (BLV) pathogenesis, four full-length BLV clones, 1, 8, 9, and 13, derived from the transformed cell line FLK-BLV and a clone construct, pBLV913,...Full Text Available

Science.gov (United States)

Recent proposals have shown that a quantum degenerate gas of alkaline earth atoms can be used for a number of novel quantum computing and quantum simulation experiments. Strontium is a good candidate for such experiments because it can be controlled with high precision, as demonstrated in recent atomic clock experiments. Unfortunately, the small scattering length of strontium is not amenable to evaporative cooling techniques that are used to reach quantum degeneracy. Furthermore, increasing the scattering length of alkaline earths with a magnetic Feshbach resonance is not possible due to their spinless electronic ground state configuration. However, recent theoretical and experimental work suggests the possibility of changing scattering lengths in alkaline earths with laser light. Using this optical Feshbach resonance near strontium's narrow ^1S0->^3P1 intercombination transition might allow its scattering ...

UK PubMed Central (United Kingdom)

The entire genome of rabies virus vaccine strain Flury-LEP-C, a Chinese variant of the rabies virus vaccine strain Flury-LEP, was sequenced. The overall length of the genome of Flury-LEP-C strain was...Full Text Available

UK PubMed Central (United Kingdom)

Centrioles are intriguing cylindrical organelles composed of triplet microtubules. Proteomic data suggest that a large number of proteins besides tubulin are necessary for the formation and maintenance...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This report describes the results of EPRI Program S404-28, titled Experimental Modeling of Eddy Current Response'', conducted by the Westinghouse Science and Technology Center (STC). The Westinghouse STC demonstrates that its mercury modeling technique provides an unique bridge between steam generator eddy current field inspection conditions and predictions obtained using recently developed analytical models. The mercury modeling technique was used systematically to explore factors which contribute to primary water stress corrosion cracking (PWSCC) sizing inaccuracy, including probe design, coil excitation frequency, crack length, and crack morphology. Two new proposed techniques for inverting crack lengths from eddy current data are compared with the technique commonly used in field data analysis for PWSCC. The performance of uniform field eddy current probes is compared with the performance of pancake coil probe designs, and ...

Science.gov (United States)

station in flowmeter used for mass flow calculation. Introduction. THE design .... length (as a result of a less conservative boundary-layer separation criterion), 2) slight ..... ical Flow, AGARD Conference Proceedings, No. 30, 1968. 5Kantrowitz ...

UK PubMed Central (United Kingdom)

The RNA packaging process for retroviruses involves a recognition event of the genome-length viral RNA by the viral Gag polyprotein precursor (PrGag), an important step in particle morphogenesis. The...Full Text Available

UK PubMed Central (United Kingdom)

Dramatic differences in the height of lima beans (Phaseolus lunatus L.) treated with two different Rhizobium strains were studied. Lima beans were grown in Perlite...Full Text Available

Science.gov (United States)

Page 1. Page 2. Page 3. Page 4. Page 5. Page 6. Page 7. Page 8. Page 9. Page 10. Page 11. Page 12. Page 13. Page 14. Page 15. Page 16. Page ...

UK PubMed Central (United Kingdom)

Background & objectives:Acanthamoeba keratitis (AK) is a painful and vision-threatening ocular infection. The differentiation of Acanthamoeba...Full Text Available

UK PubMed Central (United Kingdom)

Epicuticular wax production was evaluated along the length of expanding leek (Allium porrum L.) leaves to gain insight into the regulation of wax production. Leaf segments from the...Full Text Available

UK PubMed Central (United Kingdom)

Analysis of gestation length in an obstetric population of indigenous African women revealed a mean pregnancy duration of 274.8 days, which is similar to values recorded in women of African descent...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundInformation on more than 35 000 full-length Oryza sativa cDNAs, together with associated microarray gene expression data collected under various treatment...Full Text Available

International Nuclear Information System (INIS)

Aim: To create nomograms for renal size as measured from DMSA renal studies, and to test the nomograms for their ability to separate normal from abnormal kidneys. Method: Renal length was measured from posterior oblique views and renal area from posterior views. Results from 253 patients with bilateral normal kidneys were used to create nomograms for renal size relative to patient age, body height, weight or body surface area (BSA). The nomograms enclosed 95% of the normal kidneys, thus indicating the range for 95% confidence limits, and hence the specificity. Each nomogram was then tested against 46 hypertrophied kidneys and 46 damaged kidneys. Results: The results from nomograms of renal length and renal area, compared to age, body height, body weight and BSA are presented. For each nomogram, the range is presented as a fraction of the mean value, and the number of abnormal kidneys (hypertrophied or damaged) outside the normal range is ...

UK PubMed Central (United Kingdom)

BackgroundEmbolic events (EE) in infective endocarditis (IE) are caused by fragmentation of vegetations or valvular tissue. Vegetation length is considered to be the most potent...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In order to reduce the length and to increase the effectiveness of processing, the proposed method for acetic processing of an electric centrifugal well pump calls for covering the pressure line during the curing and periodically starting the pump.

UK PubMed Central (United Kingdom)

To determine if medium and long chain fatty acids can be appropriately metabolized by species that normally produce 16 and 18 carbon fatty acids, homogenates of developing Cuphea wrightii, Carthamus...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This report describes the results from acoustic emission (AE) and ultrasonic monitoring of the Aespoe Pillar Stability Experiment (APSE) at SKB's Hard Rock Laboratory (HRL), Sweden. The APSE is being undertaken to demonstrate the current capability to predict spalling in a fractured rock mass using numerical modelling techniques, and to demonstrate the effect of backfill and confining pressure on the propagation of micro-cracks in rock adjacent to deposition holes within a repository. An ultrasonic acquisition system has provided acoustic emission and ultrasonic survey monitoring throughout the various phases of the experiment. Results from the entire data set are provided with this document so that they can be effectively compared to several numerical modelling studies, and to mechanical and thermal measurements conducted around the pillar volume, in an 'integrated analysis' performed by SKB staff. This document provides an in-depth summary of the AE and ...

International Nuclear Information System (INIS)

The pressurized Heavy Water Reactor (PHWR) consists of horizontal calandria vessel containing a large number of pressure tubes (fuel channels) connected to the reactor inlet and outlet headers by individual feeders. Coolant flow distribution among the pressure tubes play a vital role in extraction of thermal power. For these reactors one of the design objectives is to achieve uniform coolant outlet temperatures by providing coolant flows according to the channel power. This is achieved by the design process known as feeder sizing. This basically consists of accounting for the individual channel power and centre line geometry of individual feeder and iteratively adjusting the feeder hydraulic resistances within the design constraints such as limiting flow velocities, channel flows. Recently, the first unit of 540 MWe i.e Tarapur Atomic Power Project (unit 4) has been commissioned. This paper discusses ...

UK PubMed Central (United Kingdom)

Variability in motor performance decreases with practice but is never entirely eliminated, due in part to inherent motor noise. The present study develops a method that quantifies how performers...Full Text Available

UK PubMed Central (United Kingdom)

Quartz has a dissipation factor of approximately 10(-4), which is an order of magnitude less than that of the best glasses previously used to fabricate patch pipettes; it's dielectric constant of 3.8...Full Text Available

UK PubMed Central (United Kingdom)

Dominant mutations in sarcomere protein genes cause hypertrophic cardiomyopathy, an inherited human disorder with increased ventricular wall thickness, myocyte hypertrophy, and disarray. To understand...Full Text Available

UK PubMed Central (United Kingdom)

Peptide toxins with high affinity, divergent pharmacological functions, and isoform-specific selectivity are powerful tools for investigating the structure-function relationships of voltage-gated...Full Text Available

International Nuclear Information System (INIS)

A survey is given of the influence of surface deformations on heavy ion reactions. Emphasis is put on the effect of zeropoint fluctuations in the entrance channel and on the effect on grazing collisions in terms of an imaginary part of the scattering potential. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Attention was focused on the fission process in light nuclear systems. A model calculation based on the transition-state model of nuclear fission was applied to {sup 47}V fission as populated through multiple entrance channels and to fusion-fission cross sections for production of {sup 28}Al through three different entrance channels. Angular distributions are shown for different mass channels of the {sup 29}Si+{sup 27}Al reaction at E{sub lab} = 125 MeV. Pronounced structure is seen in the symmetric and near-symmetric fission channels from the {sup 24}Mg+{sup 24}Mg reaction; cross sections for binary fragment emission are shown for E{sub lab} = 90 MeV. A large Bragg-curve detector was used in this experiment. Ways to optimize detector response were studied; in addition, the Bragg detector was instrumented with an internal position-sensitive multiwire proportional counter.

International Nuclear Information System (INIS)

This paper documents some of the recent uses of robotics for inspection and maintenance activities in Ontario Hydro's nuclear power plants in areas other than fuel channels and steam generators. 7 figs.

International Nuclear Information System (INIS)

A theoretical scheme for quantum secure direct communication (QSDC) is proposed, where a three-qubit symmetric W state functions as a quantum channel. Two legitimate communicators can transmit their secret information by using quantum teleportation and local measurements.

UK PubMed Central (United Kingdom)

Previous studies in several different trigeminal nerve injury/inflammation models indicated that the hyperexcitability of primary afferent neurons contributes to the pain pathway underlying mechanical...Full Text Available

UK PubMed Central (United Kingdom)

We report the use of cysteine-substituted mutants in conjunction with in situ oxidation to determine the physical proximity of a pair of engineered cysteines in the pore region of the voltage-gated...Full Text Available

CERN Document Server

Calcium (Ca) plays an important role in regulating various cellular processes. In a variety of cell types, Ca signaling occurs within microdomains where channels deliver localized pulses of Ca which activate a nearby collection of Ca-sensitive receptors. The small number of channels involved ensures that the signaling process is stochastic. The aggregate response of several thousand of these microdomains yields a whole-cell response which dictates the cell behavior. Here, we study analytically the statistical properties of a population of these microdomains in response to a trigger signal. We apply these results to understand the relationship between Ca influx and Ca release in cardiac cells. In this context, we use a first passage time approach to show analytically how Ca release in the whole cell depends on the single channel kinetics of Ca channels and the properties of microdomains. Using these ...

UK PubMed Central (United Kingdom)

AbstractA mechanism of how polyanions influence the channel formed by Staphylococcus aureus α-hemolysin is described. We demonstrate that the probability of several...Full Text Available

Science.gov (United States)

average bulk water temper ature rise, OF bulk water temperature at elevation z, OF bulk water temperature in channels 0 and 1, O F film temperature, OF ...

UK PubMed Central (United Kingdom)

INTRODUCTION:Gynura procumbens has been shown to decrease blood pressure via inhibition of the angiotensin‐converting enzyme. However, other mechanisms that...Full Text Available

International Nuclear Information System (INIS)

Focused-ion beam (FIB) milling provides rapid fabrication of individual cylindrical submicrometer channels with reproducible dimensions (#+-#5% diameters) through 8-#mu#m thick poly(methylmethacrylate) (PMMA) films. PMMA films are spincast on sacrificial Si carriers and sputter-coated with Au before the 30-kV gallium FIB milling process. By adding a trace amount of poly(ethyleneoxide) and poly(dimethylsiloxane) to the PMMA solution before casting, the films can be released for subsequent mounting in microfluidic devices to create hybrid microfluidic-nanofluidic multilevel architectures. In situ FIB sectioning demonstrates the smooth cylindrical surface within the pore. Placing a milled film in contact with an aqueous fluorescein solution fills the channel by capillary action, as verified by confocal fluorescence microscopy. Confocal fluorescence of dyed films reveals that the pores span the thickness of the PMMA film. Small arrays of ...

UK PubMed Central (United Kingdom)

Animals sense changes in ambient temperature irrespective of whether core body temperature is internally maintained (homeotherms) or subject to environmental variation (poikilotherms). Here we show...Full Text Available

International Nuclear Information System (INIS)