... Title : The Numerical Weather Prediction System at the Italian Air Force Weather Service: Impact of Non-Conventional Observations and Increased ...
This book contains over 20 selections. Some of the titles are: Continuum damage mechanics studies on the dynamic fracture of concrete; Dynamic compressive strength of cementitious materials; Rate-sensitivity of mode I and mode II fracture concrete; and An impact damage model of concrete.
The most important aim of the title program is to investigate the possibility to convert long-lived actinides and mobile fission products in short-lived and stable isotopes by means of nuclear transmutation and recycling. First, an overview is given of the present situation regarding fission material waste, the origin of such waste in light water reactors and the options for interim and ultimate storage. Next, attention is paid to the aim of the the RAS program, the working method and the results so far of national and international research on the transmutation of actinides and fission products. Speculative expectations for the future are briefly outlined. The report also contains four appendices with technical aspects of the title subject: the RAS program of ECN, chemical aspects of reprocessing fission material, transmutation in fission reactors and in accelerators. 12 figs., 7 tabs., 4 appendices, 57 refs.
The goal of this paper is to explore how compliance with the Clean Air Act Amendments of 1990 (CAAA), especially Title IV and emission trading under it, will affect the current relationship between state and federal regulation. It is difficult, with the limited experience we have had under Title IV, to be definitive about or to be a very strong advocate of too many policy positions. What may be most helpful at this point is to identify where the difficult issues in state/federal relations might arise; and then to explore ways in which tensions might be either avoided or resolved. One anticipated conclusion is that a traditional regulatory mindset could be very destructive if applied to this new area of oversight without due sensitivity to what Congress is trying to achieve in Title IV. That concern pervaded the early legislative debates; and it persists today. Title IV presents some unique challenges to ...
This report draws an account of the consequences of Chernobyl accident 14 years after the disaster. It is made up of 8 chapters whose titles are: (1) Some figures about Chernobyl accident, (2) Chernobyl nuclear power plant, (3)Sanitary consequences of Chernobyl accident, (4) The management of contaminated lands, (5) The impact in France of Chernobyl fallout, (6) International cooperation, (7) More information about Chernobyl and (8) Glossary.
The main purpose of the study on the title subject is to gain insight into the strategic options to optimize energy production from waste processing in the Netherlands in the long term. The developed optimization model will be used by the Dutch Ministry of Public Health, Spatial Planning en Environment (VROM) for scenarios to calculate and determine expectations and uncertainties in the development of waste processing in the Netherlands. Attention is paid to (1) the impact of present and future technology on the costs and energetic efficiency of waste processing, (2) several techniques for the generation of electricity and heat, the production of fuels, and recycling, (3) the impact of scale (capacity) on costs and energetic efficiency of waste processing installations, and (4) the impact of transport and heat distribution. The time frame is the year 2020. 66 refs.
Some results on mechanical property study of copper and titanium subjected to impact load and next to neutron irradiation are presented. It was shown that shock wave influence involves a substantial shape change of the stress-strain diagram and of respective mechanical characteristics. Yield- and ultimate strength were substantially increased, as well as hardness with a considerable drop of plasticity. Also a heat stability of copper and titanium specimens was studied after being treated with shock-waves and neutron radiation. Results are given of electron microscope study of titanium structure sfter explosion hardening, which caused decomposition of hydride segregations in titanium and increased dislocation density.
Typhoons Aere (2004) and Matsa (2005) caused high nephelometric turbidity in the Shihmen reservoir in northern Taiwan, jeopardizing the operation of the reservoir for several days, and ultimatelyimpacting the living conditions and economy of the downstream residents. The torrential rains caused landslides and debris flows in upland areas, and flowed into riverbeds, likely contributing significantly to the suspended sediment yields in the reservoir. This investigation elucidates how upland landslides affect sediment attributes in the reservoir basin. Study methods including field observations, spatial analysis in GIS and aerial photo interpretation are adopted to trace the sediment sources and contributing factors to the landslide. Torrential rains induced landslides and debris-flows uplan...
Ultimate compressive strength in the longitudinal direction. (3. Ultimate tensile strength in the transverse direction. U'. Ultimate compressive strength in ...
Pages 184-197: Understanding Personal Change in a Women’s Faith-Based Transitional Center/title link ...titleUnderstanding Personal Change in a Women’s Faith-Based Transitional Center/dc:title
Effect of oil palm empty fruit bunch (OPEFB) fiber and poly(methyl acrylate) grafted OPEFB on several mechanical properties of poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends were studied. The composites were prepared by mixing the fiber and the PVC/ENR blends using HAKEE Rheomixer at the rotor speed of 50 rpm, mixing temperature 150degreeC, and mixing period of 20 min. The fiber loadings were varied from 0 to 30% and the effect of fiber content in the composites on their ultimate tensile strength (UTS), Youngs modulus, elongation at break, flexural modulus, hardness, and impact strength were determined. An increasing trend was observed in the Youngs modulus, flexural modulus, and hardness with the addition of grafted and ungrafted fiber to the PVC/ENR blends. However the i...
Ultimate compressive strength and failure modes were studied using 24- ... to 81 % of the average ultimate compressive strength (UCS). Figure 1 (a) is the failure ...
... In fact, for dynamic loading, the ultimate compressive strength can be more than doubled (Bischoff and Perry 1991), whereas the ultimate uniaxial ...
... and testing of unidirectional composites, there are serious doubts about the possibility of obtaining a true ultimate compressive strength for this kind ...
Previous investigations have shown that both the early biological response and the mechanical properties of a porous hydroxyapatite bone graft substitute are highly sensitive to its pore structure. The objective of this study was to evaluate whether the pore structure continued to influence bone integration in the medium to long term. Two screened batches of porous hydroxyapatite (PHA) designated as batch A and batch B, with porosities of approximately 60 and 80%, respectively, were selected for this study and implanted for periods of 5, 13, and 26 weeks into the lower femur of New Zealand White rabbits. Histomorphometric analysis of the absolute volume of bone ingrowth within batch A and B implants from 5 to 26 weeks showed that the absolute volume of bone ingrowth was consistently lower in batch A (10-21%), compared to batch B implants (24-31%). However, when the volume of bone ingrowth was normalised for the available pore space, this difference was reduced (23-47% and 32-42% for ...
European research in green energy production from crops has resulted in the development of full scale bioreactors that use energy crops as feedstock. Switchgrass has been touted as one of the most promising crops for energy production among several perennial grass species grown under moderate to hot climates. However, few studies have been conducted in colder climate conditions. This study examined the mesophilic methane yield of switchgrass grown under the cooler growing conditions that exist in northeastern North America. In 2007, switchgrass was harvested in late July, August and September and conserved as silage. The regrowth of plots harvested in late July was also harvested in late September as a two-cut strategy. A 30 L small-scale laboratory digester was used to anaerobically digest the switchgrass silage samples. Specific methane yield decreased considerably with advancing plant development, but was similar between the first harvest in late July and the regrowth in late ...
Anadromous salmon in the Columbia River Basin are presently far below historic level of production, due to the impacts of development in the basin. To halt the downward trend in production and ultimately increase returns, the Northwest Power Planning Council developed the Columbia River Basin Fish and Wildlife Program. The Program outlines a coordinated plan for restoring anadromous salmonid runs to the basin. The goals and objectives outlined in the Program require addressing a complex set of problems that encompass a broad range of social, political, economic and biological issues. Resolution of these problems will require the efforts of a number of federal, state, and tribal agencies that have regulatory authority over activities that either directly or indirectly affect anadromous salmonids in the basin. Resource managers have realized the need for coordination in these efforts. The Coordinated Information System is designed to share ...
For years, the writing has been on the wall about the impact of climate change on the people, plants, animals, and habitats of Latin America and the Caribbean. Now, day-to-day experiences and eye-witness accounts from leading environmental and development groups are proving predictions to be correct. In the late 1990s, the world's pre-eminent group of climate scientists gathered under the Intergovernmental Panel on Climate Change (IPCC) and predicted a devastating range of impacts, including an increase in the intensity and number of extreme weather events exacerbating natural disasters, forest die-off, melting glaciers, and the drying out of temperate grasslands. The region's huge geographical diversity means that patterns of vulnerability to climate change are extremely varied. It also makes modelling difficult, although this is constantly improving. To avoid misunderstanding, it is important to point out that with or ...
A workshop on radioactivity in coal use was held on September 15 through 17, 1981, under the auspices of the US Department of Energy, Office of Environmental Programs, and the Los Alamos National Laboratory. The purpose of the workshop was to identify research issues associated with radioactivity resulting from the use of coal for electric power generation. The concensus of the 10 scientists participating in the workshop was that a moderate to strong need exists for research in solubility of fly ash in different fluids and for determination of radioactivity in construction materials. Several additional research issues were identified but were given a lower priority. Summaries of each presentation are included. Titles are: some effects of coal combustion on the radiation environment; radionuclides in western coal at Mound; low-level radiation in coals utilized and ashes produced at New York State electric utilities; radioactivity from coal use - where are the ...
Ultimate Compressive Strength of Short Sheet-Stringer Panels With Special. Reference to the Influence of the Riveted Connection Between Sheet and. Stringer ...
... Problems investigated in various basic hollowness ratios include ultimate compressive strength, fatigue properties, buckling characteristics, and ...
The behavior of melter feed (a mixture of nuclear waste and glass-forming additives) during waste-glass processing has a significant impact on the rate of the vitrification process. We studied the effects of silica particle size and sucrose addition on the volumetric expansion (foaming) of a high-alumina feed and the rate of dissolution of silica particles in feed samples heated at 5 C/min up to 1200 C. The initial size of quartz particles in feed ranged from 5 to 195 {micro}m. The fraction of the sucrose added ranged from 0 to 0.20 g per g glass. Extensive foaming occurred only in feeds with 5-{micro}m quartz particles; particles {ge}150 {micro}m formed clusters. Particles of 5 {micro}m completely dissolved by 900 C whereas particles {ge}150 {micro}m did not fully dissolve even when the temperature reached 1200 C. Sucrose addition had virtually zero impact on both foaming and the dissolution of silica particles. Over 100 sites in the United ...
...October 2006 - present: University of Leeds, UK PhD Candidate in Geochemistry Thesis Title: Magnetite formation in reducing natural environments Supervisors: Dr Liane G. Benning ...Germany Bachelor of Science in Geosciences and Astrophysics Project Details Project Title: \\
comprehensive description for this model is available through AGARD, Reference [8]. ... Specifically, there is a pocket of flow separation at the side-of- body ...
... Title : Refining the Magnetic Forming Capability. ... Abstract : The purpose of this project was to refine the in-house magnetic forming capability. ...
... Title : Optical Images Due to Lenses and Mirrors. ... Abstract : The properties of real and virtual images formed by lenses and mirrors are reviewed. ...
... Title : Military Working Dog Procurements. ... Our primary objective was to determine whether recent procurements of military working dogs by the ...
... Title : Mental Health and Resilience: Soldiers' Perceptions about Psychotherapy, Medications, and Barriers to Care in the United States Military. ...
... Title : Effects of Pentobarbital Anesthesia on Survival, 'Escherichia coli' Clearance, Glucose and Leukocyte Concentration in Dogs Subjected to ...
... Title : Effect of Yttrium on the Microstructure of Titanium Alloys,. ... The yttrium was added in the melting stage as an oxide or in the elemental form. ...
Nitrogens, Sulfurs, Isotopes, and Hydrocarbons Gases Elements Ions and Inorganic Acids Organic Compounds Co-eluting Organics Hopanes, Cholestanes, and Sterols Pesticides,...
If you missed the ARTE programme entitled "L'Ultime Particule" broadcast in February, you have another chance to catch it in CERN's Main Auditorium on 13 March. "L'Ultime Particule" is a documentary by the French director Michel Andrieu that seeks to explain particle physics through a contemplative quest for the research physicists of matter of today and yesteryear. Invariably kitted out in a red parka and a soft hat, the programme's investigator scours the planet and the archives in search of the research physicists who are stalking the ultimate particle, the Higgs boson, in their quest to understand the structure of matter. Naturally enough, CERN is an important stage of his journey where Michel Andrieu and his team spent several days last year. Both from the physics and metaphysical points of view, "L'Ultime Particule" is worth seeing. The film's director, Michel Andrieu, will introduce his ...
... 500 ppm, boron increases the 0.2% offset strength; results show that boron doping does not appreciably affect ultimate compressive strength; for 0 ...
... by the boron doping in most of the alloys except for Al66Mn9Zr25 + 50 ppm B alloy; permanent deformation at ultimate compressive strength is not ...
Ultimate Compressive Strength of Short Sheet - Stringer Panels With Special. Reference to the Influence of the Riveted Connection Between Sheet and Stringer ...
Cutaneous scarring can cause patients symptoms ranging from the psychological to physical pain. Although the process of normal scarring is well described the ultimate cause of pathological scarring...Full Text Available
... The measured elastic modulus was fairly close to the predicted value, but the ultimate compressive strength (UCS) was quite a bit below the MSC ...
This paper presents extensive non-linear finite element (FE) analysis and formulation development work carried out on the ultimate compressive strength of plates and stiffened panels of ship structures. A review of contemporary designs for large ships was carried out. The existing formulae for plate ultimate compressive strength were reviewed and compared with non-linear FE analysis results. A semi-analytical formula for ultimate compressive strength assessments of stiffened panels was proposed and is described. The developed formula was verified against results using ABAQUS non-linear FE software for a series of 61 stiffened panels and a good agreement between the proposed formula and FE results were achieved. The method was verified against a large number of published FE results and was ...
The most frequent ultimate cause of death is myocardial arrest. In many cases this is due to myocardial hypoxia, generally arising from failure of the coronary macro- and microcirculation to deliver...Full Text Available
Future insertion quadrupoles with large apertures and high gradients will be required for the Phase II luminosity upgrade (10{sup 35} cm{sup -2}s{sup -1}) of the Large Hadron Collider (LHC). Although improved designs, based on NbTi, are being considered as an intermediate step for the Phase I upgrade, the Nb{sub 3}Sn conductor is presently the best option that meets the ultimate performance goals for both operating field and temperature margin. As part of the development of Nb{sub 3}Sn magnet technology, the LHC Accelerator Research Program (LARP) developed and tested several 1-meter long, 90-mm aperture Nb{sub 3}Sn quadrupoles. The first two series of magnet used OST MJR 54/61 (TQ01 series) and OST RRP 54/61 (TQ02 series) strands. The third series (TQ03) used OST RRP 108/127 conductor. The larger number of sub-elements and the consequent reduction of the effective filament size, together with an increased fraction of copper and a lower Jc were expected to improve ...
Silanization of the silica gel surface in the synthesis of silica gel polyamine composites uses (chloropropyl)-trichlorosilane (CPTCS). It is possible to substitute a molar fraction of reagent CPTCS with methyltrichlorosilane (MTCS), creating a mixed silane surface layer. Two types of silica gels were modified with a series of MTCS:CPTCS molar ratios. Solid-state CP/MAS 29Si and 13C NMR spectroscopies were used to evaluate the surface silane composition. Surface silane coverage was markedly improved for the resulting gels. When polyamines were grafted to the resultant MTCS:CPTCS silane layers, it was shown that the decrease in the number of propyl attachments to the polyamine resulted in increased quantities of ''free amines''. Optimum MTCS:CPTCS ratios were determined for three polyamines grafted onto one silica gel. A substantial free amine increase was observed for poly(allylamine) (PAA). Metal uptake studies show increases in Cu(II) capacity ...
Silanization of the silica gel surface in the synthesis of silica gel polyamine composites uses (chloropropyl)-trichlorosilane (CPTCS). It is possible to substitute a molar fraction of reagent CPTCS with methyltrichlorosilane (MTCS), creating a mixed silane surface layer. Two types of silica gels were modified with a series of MTCS:CPTCS molar ratios. Solid-state CP/MAS 29Si and 13C NMR spectroscopies were used to evaluate the surface silane composition. Surface silane coverage was markedly improved for the resulting gels. When polyamines were grafted to the resultant MTCS:CPTCS silane layers, it was shown that the decrease in the number of propyl attachments to the polyamine resulted in increased quantities of ''free amines''. Optimum MTCS:CPTCS ratios were determined for three polyamines grafted onto one silica gel. A substantial free amine increase was observed for poly(allylamine) (PAA). Metal uptake studies show increases in Cu(II) capacity ...
Full text.This study focuses on the management of municipal solid waste (MSW) in Lebanon. It addresses the current status of MSW management in Lebanon in terms of collection, transport and disposal, infers the associated impacts of such practices and discusses mitigation measures and finally proposes basic guidelines for a national strategy for solid waste management in the country. The study is based on available previous investigations and on a field survey of 113 villages in four different countries. The study revealed the absence of an effective environmental policy and poor collection and disposal methods throughout the country, except for the Greater Beirut Area (G A), where better solid waste management practices are employed. Although collection of MSW outside GBA was found to be acceptable by local authorities, resources (labor and equipment) were not used efficiently. Furthermore, treatment of collected waste is almost not available. Waste collected is ...
Polymer matrix composites are presently used in many fields due to their excellent mechanical properties such as high specific strength and stiffness. However, not much is known of these composites' response to impact loading, which usually occurs at strain rates much higher than the strain rates used to measure the quasi-static mechanical properties of materials. The use of static properties in the study of structures that undergo dynamic loading can produce excessive design weight or cause unexplained and untimely failure. The studies included in this dissertation provide the results of Split Hopkinson Pressure Bar experiments to determine the ultimate compressive strength and strain of composites at high strain rates. Most researchers are using specimens with different dimensions and geometry. For this reason, it is difficult to compare results of tests done by different people. Herein, the Split Hopkinson Pressure Bar facility at the ...
The main conclusion of the study on the title subject is that the impacts of climatic change in the Netherlands are still limited. However, the impacts will be stronger in the next decades and will be even problematic at the end of this century. In this book an overview is given of probable changes in the climate for the Netherlands, danger for flooding in specific areas of the Netherlands, changes of the nature, impacts for agriculture, tourism and recreation, and industry and businesses, and risks for public health. [Dutch] De effecten van klimaatverandering in Nederland zijn nu nog beperkt. Ze zullen echter de komende decennia toenemen, maar pas tegen het eind van deze eeuw problematisch worden. Dat is de hoofdboodschap van de titelstudie. De studie is opgesteld in samenwerking met een reeks instellingen, die zijn verenigd in het Platform Communicatie Klimaatverandering (PCCC). Het klimaat verandert: ...
Ophir Corporation was awarded a contract by the U. S. Department of Energy, National Energy Technology Laboratory under the Project Title ''Airborne, Optical Remote Sensing of Methane and Ethane for Natural Gas Pipeline Leak Detection'' on October 14, 2002. This second six-month technical report summarizes the progress made towards defining, designing, and developing the hardware and software segments of the airborne, optical remote methane and ethane sensor. The most challenging task to date has been to identify a vendor capable of designing and developing a light source with the appropriate output wavelength and power. This report will document the work that has been done to identify design requirements, and potential vendors for the light source. Significant progress has also been made in characterizing the amount of light return available from a remote target at various distances from the light source. A great deal of time ...
This is the final report of a three year DOE funded project titled ''A real-time coal content/ore grade (C{sub 2}OG) sensor''. The sensor, which is based on hyperspectral imaging technology, was designed to give a machine vision assay of ore or coal. Sensors were designed and built at Resonon, Inc., and then deployed at the Stillwater Mining Company core room in southcentral Montana for analyzing platinum/palladium ore and at the Montana Tech Spectroscopy Lab for analyzing coal and other materials. The Stillwater sensor imaged 91' of core and analyzed this data for surface sulfides which are considered to be pathfinder minerals for platinum/palladium at this mine. Our results indicate that the sensor could deliver a relative ore grade provided tool markings and iron oxidation were kept to a minimum. Coal, talc, and titanium sponge samples were also imaged and analyzed for content and grade with promising results. This ...
... Title : Wear Rate and Friction Coefficient in Liquid Nitrogen and Hydrogen of Steel Sliding on Polymer Laminates (Various Fabrics and Polymers. ...
... Accession Number : ADD815206. Title : Waterjet Cutting System Adds Value to Titanium Parts. Descriptive Note : Journal article. Corporate Author : ...
... Accession Number : AD0749455. Title : Uptake and Retention of Adenine Moiety by Stored Human Red Blood Cells. Descriptive Note : Interim rept.,. ...
Two days of hearings on Titles V and X of the Water Resources Development Act of 1983 brought comments from representatives of several states, farm and transport industries, environmental groups, and concerned taxpayers. Title V requires the collection of new funds from users beyond a ceiling set for annual spending on water projects, while Title X proposes a cost-sharing partnership for certain navigation projects. Witnesses were requested to confine their comments to constructive alternatives to the proposed legislation. Additional material on the deep river study and statements submitted for the record follow the testimony of 28 witnesses.
... Mirrors (Preprint) Ryan Conk et al. 15 September 2006 ... 4. TITLE AND SUBTITLE Stress Coatings for Large Scale Membrane Mirrors (Preprint) 5a. ...
... TITLE (Include Security Classification) Sorption of Selected Volatile Organic Constituents of Jet Fuels and Solvents on Natural Sorbents from Gas ...
... Accession Number : ADD135818. Title : Performance of Titanium in Flue Gas Desulfurization Scrubber Systems,. Descriptive Note : Journal Article,. ...
... Accession Number : ADD431225. Title : Influence of Fiber Loading on Thermal Ablation of PTFE,. Corporate Author : Personal Author(s) : Letson,KN. ...
Title: Illicit Crops in Tropical America: Deforestation, Landslides, and the Terrestrial Carbon Stocks. Author: Lopez-Rodriguez, Sara R.; Blanco-Libreros, Juan F. ...
The activities and the policy in the Netherlands regarding the development of the title systems since 1990 are briefly outlined, focusing on the use of PV-systems in buildings. 5 figs., 1 tab.
Sep 1, 2011 ... Publication Information. Bookmark and Share. Title: Arc Habitat Suitability Index computer software. Author: Juntti, Thomas M.; Rumble, Mark A. ...
Sep 1, 2011 ... Title: Application of chloropicrin to Douglas-fir stumps to control laminated root rot does not affect infection or growth of regeneration 16 growing ...
High Cycle Fatigue Initiative Workshop -Active Vibration. Control/Engine. Health Monitoring Session December 10,. 1996. The presentation was titled "Active ...
on the range of available deforestation, forest degradation, ... Results: Deforestation estimates showed good agreement for multi-year trends of increasing ...
Air Show. The exhibit will feature 16 fuel companies showcasing cutting-edge alternative jet fuel technologies. In addition to individual company exhibits, the Showcase will...
National Institutes of Health Mucosal Immunology and Microbiome Interest Group Search Go Search Skip Navigation Links SIGS > Mucosal Immunology and Microbiome Interest Group Skip...
The ''Enabling & Information Technology To Increase RAM for Advanced Powerplants'' program, by DOE request, was re-directed, de-scoped to two tasks, shortened to a 2-year period of performance, and refocused to develop, validate and accelerate the commercial use of enabling materials technologies and sensors for coal/IGCC powerplants. The new program was re-titled ''Enabling Technology for Monitoring & Predicting Gas Turbine Health & Performance in IGCC Powerplants''. This final report summarizes the work accomplished from March 1, 2003 to March 31, 2004 on the four original tasks, and the work accomplished from April 1, 2004 to July 30, 2005 on the two re-directed tasks. The program Tasks are summarized below: Task 1--IGCC Environmental Impact on high Temperature Materials: The first task was refocused to address IGCC environmental impacts ...
Geologic sequestration is currently being practiced and scientifically evaluated as a critical component in a broad strategy, comprising new practices and technologies, for mitigating global climate change due to anthropogenic emissions of CO2. Demonstrating that geologic sequestration of CO2 is safe and effective, and gaining public acceptance of sequestration technologies are critically important in meeting these global climate change challenges. Monitored field-scale demonstrations of geologic sequestration of carbon dioxide will contribute greatly toward growing trust and confidence in the technology; however, pilot demonstrations ultimately will not be the norm for new geological sequestration deployments. Instead, scientists, engineers, regulators, and ultimately the public will rely on numerical simulations to predict the performance of geologic repositories for carbon dioxide sequestration. The U.S. Department of Energy (DOE), through ...
The existence of problems with wild pigs (Sus scrofa) is nothing new to the Western Hemisphere. Damage by these introduced animals was reported as far back as 1505 by the early Spanish colonies in the Caribbean, where wild pigs were killing the colonists cattle. Droves of these animals also ravaged cultivated crops of maize and sugarcane on islands in the West Indies during this same time period. These wild pigs reportedly were very aggressive and often attacked Spanish soldiers hunting rebellious Indians or escaped slaves on these islands, especially when these animals were cornered. The documentation of such impacts by introduced populations of this species in the United States has subsequently increased in recent years, and continued up through the present (Towne and Wentworth. 1950, Wood and Barrett 1979, Mayer and Brisbin 1991, Dickson et al. 2001). In spite of a fairly constant history in this country since the early 1900s, wild pigs have had a dramatic ...
Biomass tensile and shear ultimate failure stresses were measured with the aim of identifying biomass 'weakest mode of failure' or 'natural fracture point' as a basis for future grinder designs. Switchgrass (Panicum virgatum L.) ultimate stresses were determined for Alamo and Kanlow varieties over ranges in maturity and moisture content. Alamo had greater ultimate tensile stress than Kanlow (P=0.0091), with mean values of 97.8 and 89.7MPa, respectively. Alamo had greater ultimate shear stress than Kanlow (P=0.0091), with mean values of 20.5 and 17.9MPa, respectively. Shear was the 'weakest mode of failure'. Grinders that use knives, shear bars, and mechanical pinch points that apply opposed-sliding actions are expected to be more energy efficient. Mean ultimate tensile stress and shear stress were significantly different between ...
In the present paper, a possible interaction region layout of the VLEPP based Photon Linear Collider (PLC) with ultimate luminosity is discussed. In order to remove spent electron beams, the crab-crossing scheme is used. The detector is protected from produced pairs and secondary particles by means of the detector magnetic field and a shielding mask. ((orig.)).
The concept of preliminary transmutation of minor actinides before placement to the long-term storage is considered. The purpose of such preliminary transmutation before ultimate storage is to incinerate a part of actinides and to transform another part into new actinides providing low level of radiotoxicity accumulated in the storage. Modes of transmutation in reactors of PWR, PHWR (CANDU), and Superfenix types are compared. Among power reactors, heavy-water PHWR type reactor is most acceptable for preliminary transmutation. (author)
In this paper, an amount of confining reinforcement required for the sufficient flexural ductility of reinforced concrete column was investigated. An equation to calculate the required confining reinforcement ratio was deduced from the analytical investigation and examination on the previous experimental data as to the effects of various factors on the required confining reinforcement ratio. The rotation angle required in plastic hinges, the axial force ratio, the material properties such as concrete strength, and the ratio of core area to the whole area of column sections were employed as the factors. From the examination of the equation, it was shown that the ultimate rotation in plastic hinges calculated by the equation was more conservative than the ultimate rotaion angle of members obtained by test column specimens. It was also indicated that the ultimate rotation angle of members of columns failed in shear was smaller ...
nl/guid /item item titleNieuwe rol overheid nodig voor schone economie/title ...nl/nieuws/nieuwsberichten/2011/nieuwe-rol-overheid-nodig-voor-schone-economie/link description<p>De in de maatschappij ...gt; <a href="/nieuws/persberichten/2011/nieuwe-rol-overheid-nodig-voor-schone-economie">Nieuwe rol overheid nodig voor schone
The bone mineral content of 109 lumbar vertebrae from 36 different subjects was determined by dual photon absorptiometry. The mean age of the subjects was 58.5 years (range, 31 to 79 years). The ultimate strength of the vertebral bodies was determined during axial compression. Bone mineral content and ultimate compressive strength were correlated (r = 0.86) and the strength was found to increase linearly with increasing amounts of bone mineral content. No differences in this correlation were found in the four vertebral levels (L-4) included in the study, but a difference in this correlation was found between specimens taken from male and female subjects. The results make it possible to estimate the strength of a vertebral body from the knowledge of its bone mineral content as determined by dual photon absorptiometry and provide a basis of estimations of normal and abnormal amounts of bone mineral content in the vertebrae of the lumbar spine. ...
This paper describes new test methodologies to obtain data used to evaluate the ultimate seismic strength of Nuclear Power Plant (NPP) equipment related to nuclear safety. The paper first reviews existing equipment seismic test data from the viewpoint of the evaluation of their ultimate seismic strength and/or seismic design margins, and extracts the issues in the existing data with regard to their applicability to the evaluation. Then, the paper proposes new test methodologies for the equipment to evaluate their ultimate seismic strength. The test methodology of the equipment employs a vibration amplification system to a shaking table and enhances its applicable maximum acceleration up to 6g. The test methodology herein is cost effective for obtaining test data that is indispensable for evaluating proper seismic margins of NPPs. (author)
Binding of epidermal growth factor (EGF) to the EGF receptor (EGFR) initiates signal transduction, ultimately leading to altered gene expression. Ligand-activated EGFR is also rapidly internalized...Full Text Available
Compliance mismatch is a significant challenge to long-term patency in small-diameter bypass grafts because it causes intimal hyperplasia and ultimately graft occlusion. Current engineered grafts...Full Text Available
Retinitis pigmentosa (RP) is a heterogeneous group of inherited retinal dystrophies characterised ultimately by the loss of photoreceptor cells. We have recently identified a new gene (EYS) encoding...Full Text Available
Although functional organ stem cells persist in the old, tissue damage invariably overwhelms tissue repair, ultimately causing the demise of an organism. The poor performance of stem cells in an aged...Full Text Available
Most hospitals today are quickly developing special programs and services that are designed to compete for physicians and patients, and ultimately fill unoccupied beds. In an attempt to attract physicians...Full Text Available
The load-carrying capacity and ultimate deformation capacity of timber-concrete composite systems can be significantly influenced by the ductility of the connection between the two materials. The use of more ductile connections can increase the load-carrying capacity of the composite system as well as its ultimate deformation capacity. In this work, the potential increase that might be expected for these two parameters due to the use of ductile connections will be assessed through numerical simulations, taking the non-linear behaviour of the connections into account. Furthermore, the connection ductility required to achieve the maximum load capacity depends on the mechanical properties of the connection as well as on the geometric and mechanical properties of the composite system. There ar...
We have made preliminary estimates of charged particles background at the 100x100 GeV Photon Linear Collider with ultimate luminosity. The charged particles background due to electromagnetic processes is located mainly in the small-angle range of the detector. At large angles, the number of background particles is much smaller. Analysis of the background (at least, in the range under consideration) shows that background conditions for the VLEPP-based Photon Linear Collider are better than at the VLEPP electron-positron collider. ((orig.)).
When biomass is used as fuel for thermal conversion plants, minerals from the fuel can be responsible for major problems. Generally, these problems are associated with the existence and development of low melting compounds or eutectics, which form sticky layers. In a fluidised bed, this can result in bed-agglomeration and defluidisation. This causes local high temperature, which often accelerates the process. It ultimately can lead to a completely sintered bed content with a glassy phase gluing the bed particles together and shut-down of the plant. The main objective of the title project is to develop a methodology to predict ash/bed agglomeration and sintering problems, to indicate related problems and, furthermore, to identify solution methods to make different types of biomass streams more viable for energy production. Within the present study, selected fuels are subjected to different existing methods together with some new ones, in order ...
Sep 1, 2011 ... Title: THINEX - an expert system for estimating forest harvesting productivity and cost. Author: LeDoux, C. B.; Gopalakrishnan, B.; Pabba, R. S. ...
This volume contains 5 appendices. Title listing are: technologies for recovery of transuranics; nondestructive assay of TRU contaminated wastes; miscellaneous waste characteristics; acceptance criteria for TRU waste; and TRU waste treatment technologies.
... Accession Number : ADB119274. Title : Transdermal Drug Delivery System. Stage 1. Volume 1. Descriptive Note : Final rept. 15 Aug 85-14 Oct 87,. ...
The manual was prepared for State and local government officials, local emergency planning committee (LEPCs), and other community groups that want to make Title III work. It is intended as a practical guide for those who have little or no previous experience in the field of communication, whose time must be snatched from home and office, and whose resources are limited. The manual has three major sections: Part I discusses planning, which is vital to the success of a communication program; Part II suggests ways to get and keep people involved, especially important because Title III affects so many different sectors of the community; Part III, a how-to-do-it section, talks about specific tasks, such as giving a speech or writing a press release. Appendices include a detailed explanation of the law, a glossary, a list of recent studies related to Title III communications, a list of educational materials, and a list of State ...
French ... Orig. Title Scintigraphie osseuse quantifiee chez l'enfant et l'adolescent - repartition selon l'age des taux de fixation de diverses pieces osseuses normales.
French English ... Orig. Title Imagerie IRM des lesions focales hepatiques avec les antennes de surface en reseau phase (phased array): apnee ou imagerie haute resolution?.
Our primary objective was to determine whether recent procurements of military working dogs by the 341st Training Squadron complied with section 10a, title 41, United States Code (41 U.S.C. 10a commonly known as the Buy American Act) and other procurement...
Equipped with terahertz sensors, the Aura mission will see far more ... We introduce you to a few amazing individuals, all sharing the dubious title of rocket scientist . And a ..... similar thing happens with incoming light. Astronomers call it the ...
Materials World Network: Cooperative Activity in Materials Research between US Investigators and ... Program Title: Materials World Network: Cooperative Activity in Materials Research between US ...
Materials World Network: Cooperative Activity in Materials Research between US Investigators and ... Program Title: Materials World Network: Cooperative Activity in Materials Research between US ...
Portuguese ... Orig. Title Isolamento e identificacao do flavonoide (-)-4'-metil-epigalocatequina das raizes de Maytenus obtusifolia Mart. (Celastraceae)
Information circulars are published from time to time under the symbol INFCIRC/... for the purpose of bringing matters of general interest to the attention of all Members of the Agency. The present revision contains INFCIRCs published up to mid-August 1994. A complete numerical list of information circulars is reproduced with their titles in the Annex.
Sep 1, 2011 ... Title: Hardness, density, and shrinkage characteristics of silk-oak from Hawaii. Author: Youngs, R. L.. Date: 1964. Source: Research note FPL ...
Title: FY 2004 Energy Management and Conservation Program Annual Report ...Energy Management and Conservation Program ...Environmental Protection Agency Office of Administration and Resources Management 1200 Pennsylvania Avenue, NW (3101A)
Bulgarian ... Orig. Title Vliyanie na gama-lychite vyrkhu spirokheti ot vida Borrelia anserina, Sakharoff, 1891. Chast 2. Promeni v antigenniya stroezh.
An azido-"1"2"5iodo-ansamycin (1) in the geldanamycin family was prepared in two steps in one reaction vessel from 17-amino-22-(4'-aminophenacyl)-17-demethoxygeldanamycin (3). The title compound was suitable for photoaffinity labeling proteins that interacted with ansamycins. An alternative synthesis is reported for preparation of unlabeled title compound in order to afford practical amounts of (1) for conventional biochemical studies. (Author).
An azido-[sup 125]iodo-ansamycin (1) in the geldanamycin family was prepared in two steps in one reaction vessel from 17-amino-22-(4'-aminophenacyl)-17-demethoxygeldanamycin (3). The title compound was suitable for photoaffinity labeling proteins that interacted with ansamycins. An alternative synthesis is reported for preparation of unlabeled title compound in order to afford practical amounts of (1) for conventional biochemical studies. (Author).
This final scientific report documents the Industrial Technology Program (ITP) Stage 2 Concept Development effort on Data Center Energy Reduction and Management Through Real-Time Optimal Control (RTOC). Society is becoming increasingly dependent on information technology systems, driving exponential growth in demand for data center processing and an insatiable appetite for energy. David Raths noted, 'A 50,000-square-foot data center uses approximately 4 megawatts of power, or the equivalent of 57 barrels of oil a day1.' The problem has become so severe that in some cases, users are giving up raw performance for a better balance between performance and energy efficiency. Historically, power systems for data centers were crudely sized to meet maximum demand. Since many servers operate at 60%-90% of maximum power while only utilizing an average of 5% to 15% of their capability, there are huge inefficiencies in the consumption and delivery of power in these data centers. ...
The possible parameters of a photon linear collider at its ultimate luminosity, based on the VLEPP physics and technology V.E. Balakin et al., Proc. 6th Nat. Conf. on Accelerators, Dubna, 1978; V.E. Balakin, Proc. 4th Int. Workshop on Next Generation Linear Colliders, Garmisch, 1992, are presented. At a photon energy of 100x100 GeV the maximum achievable luminosity is about 1x10{sup 36} cm{sup -2} s{sup -1}. Beam parameters, luminosity characteristics, and ways to reduce the background are considered as well. ((orig.)).
Ni-free shape memory alloys are promising functional materials for medical applications. A newly developed Ti-Mo based shape memory alloy shows superelasticity after thermomechanical treatment. However, the microstructure evolution and precipitation during thermomechanical processes are still not well understood. In the present paper, compressive deformation behavior at a series of temperatures of 298K - 973K and tensile deformation behavior of the alloy after aged at 573K - 973K have been investigated systematically. It is found that the compressive yield stress and ultimate compressive strength change with the deformation temperature. The ultimate tensile strength and yield stress of aged specimens also change with the aging temperature following a non-linear relationship. Microstructures of aged specimens as well as effects of lattice softening and aging-induced precipitates on the deformation behavior have been investigated and discussed.
Nat'l Training Center Contact Us Directory Email Us BLM > Socioeconomic Impacts > Timber Print Page Socioeconomic Impacts from Timber BLM-administered lands yielded $337...
Wade. Jackson. - Army. VTD at NASA. Langley. ABSTRACT. Panel size has a large effect on the impact response and resultant damage level of honeycomb sandwich ...
This poster, submitted for the CU Energy Initiative/NREL Symposium on October 3, discusses the impacts of renewable fuel and electricity standards on state economies.
This paper presents experimental data and an computational model of the cold spray solid particle impact process. Copper particles impacting onto a polished stainless steel substrate are examined. The high velocity impact causes significant plastic deformation of both the particle and the sub- strate, but no melting is observed. The plastic deformation exposes clean surfaces that, under the high impact pressures, result in significant bond strengths between the particle and substrate. Experimental measurements of the splat and crater sizes compare well with the numerical calculations. It is shown that the crater depth is significant and increases with impact velocity. However, the splat diameter is much less sensitive to the impact velocity. It is also shown that the geometric lengths of the splat and crater scale linearly with the diameter of the ...
ObjectiveTo evaluate the impact of an interconceptional antibiotic regimen on the endometrial microbial flora and histology.Study DesignFull Text Available
Abstract: We present a generic scoring system that compares the impact of alien species among members of large taxonomic groups. This scoring can be used to identify the most harmful alien species so that conservation measures to ameliorate their negative effects can be prioritized. For all alien mammals in Europe, we assessed impact reports as completely as possible. Impact was classified as either environmental or economic. We subdivided each of these categories into five subcategories (environmental: impact through competition, predation, hybridization, transmission of disease, and herbivory; economic: impact on agriculture, livestock, forestry, human health, and infrastructure). We assigned all impact reports to one of these 10 categories. All categories had impact scores that ranged f...
Most analyses of the alternative strategies used by utilities to comply with Title IV requirements have focused on factors directly related to controlling sulfur dioxide (SO{sub 2}) emissions. However, utilities must meet a number of additional environmental requirements at the same tune they comply with the acid rain program. To illuminate the potential synergies and conflicts that might exist between the other regulatory mandates and the acid rain program, a thorough examination of all the various programs and their interrelationships must be conducted. This paper reviews the environmental mandates that utilities will have to plan to meet in the next decade concurrently with the acid rain program, and it analyzes the interactions among the various programs to identify potential synergies and conflicts.
Los Alamos National Laboratory (the Laboratory) is subject to emissions reporting requirements for regulated air contaminants under Title 20 of the New Mexico Administrative Code, Chapter 2, Part 73 (20 NMAC 2.73), Notice of Intent and Emissions Inventory Requirements. The Laboratory has the potential to emit 100 tons per year of suspended particulate matter, nitrogen oxides, carbon monoxide, sulfur oxides, and volatile organic compounds. For 1998, combustion products from the industrial sources contributed the greatest amount of criteria air pollutants from the Laboratory. Research and development activities contributed the greatest amount of volatile organic compounds. Emissions of beryllium and aluminum were reported for activities permitted under 20 NMAC 2.72 Construction Permits.
An experimental and analytical study was performed to improve understanding of the dynamic impact behavior of carbon steel pipes. The test program addressed two types of pipe impact scenarios using both 2- and 4-in. Sch-80 pipes and elbows. Projectile-on-pipe tests simulated the behavior of a stationary target pipe which is impacted at its center by a larger, more rigid whipping pipe. These target pipes, which contained non-flowing water at about 290{degree}C temperature and ca 8.5 megapascals pressure, exhibited a peak deformation of up to 45% reduction in their diameter. For each test condition, the local deformation at the impact zone is a function of the peak impact force and impact velocity. Pipe-on-wall tests simulated the impact of an elbow at the free end of a cantilevered whipping pipe with a rigid barrier. The peak crush of the ...
Efficient and economical utilization of wind power will require the ability to measure and ultimately predict the effects fluctuations in the incident wind will have on a wind turbine. In order to quantitatively assesss these effects, experimental techniques have been developed which allow analysis of full-scale performance of wind turbines with particular emphasis on the effects caused by turbulence in the incident wind. Examples of these techniques are presented using data from the DOE/Sandia Vertical Axis Wind Turbine (VAWT) program.
Experiments contributing to the understanding of the aerodynamics of airfoils operating in the vertical axis wind turbine (VAWT) environment are described. These experiments are ultimately intended to reduce VAWT cost of energy and increase system reliability. They include chordwise pressure surveys, circumferential blade acceleration surveys, effects of blade camber, pitch and offset, blade blowing, and use of sections designed specifically for VAWT application.
To the crushed ore leaching is applied. The resulting solid-liquid mixture is fed to a hydro-cyclon grading facility; here the superfine grain is separated before the concentrated mixture can be filtered or centrifuged. The grading is done in several steps. From the liquid, ultimately ridded of the solid, uranium compounds are precipitated and the yellow cake is obtained. (DG).
An AHR (Advanced HANARO Reactor) based on the HANARO has been conceptually developed for the future needs of research reactors. Generally, a natural convection cooling in nuclear installations is an ultimate heat removal mechanism as an inherent safety feature. This paper presents the preliminary thermal hydraulic characteristics and safety margins for a natural convection cooling in the AHR.
Certain transition metal chalcogenides are promising materials for use as cathodes in nonaqueous lithium batteries involving the intercalation into these layered compounds. The electrochemical behavior of the chalcogenides depends on various properties such as structure, stoichiometry, electrical conductivity, crystal morphology, etc. The influence of these properties and of the ultimate practical application of the battery on the selection of cathode material is discussed. Battery performance of selected cathode materials is discussed and life limitations due to the limited cycle life of lithium anodes are outlined. 15 refs.
The mechanical properties of TS 6 (Ti--10 percent Cr--7 percent V--3.5 percent Mo--3 percent Al) alloy were studied. Results are presented in plots showing yield stress vs cold work, notched tensile strength vs unnotched tensile strength, and ultimate tensile strength vs test temperature.
An energy frontier or QCD Explorer ep and collider can be realized by colliding high-energy photons generated by Compton backscattered off a CLIC electron beam, at either 75 GeV or 1.5 TeV, with protons or ions stored in the LHC. In this study we discuss a performance optimization of this type of collider by tailoring the parameters of both CLIC and LHC. An estimate of the ultimately achievable luminosity is given.
The Tank Waste Remediation System (TWRS) Information Systems Definition architecture evaluated information Management (IM) processes in several key organizations. The intent of the study is to identify improvements in TWRS IM processes that will enable better support to the TWRS mission, and accommodate changes in TWRS business environment. The ultimate goals of the study are to reduce IM costs, Manage the configuration of TWRS IM elements, and improve IM-related process performance.
This document defines the requirements for the GPRS (General Packet Radio Service) infrastructure as part of the Dutch Smart Meter Specification. In this document all requirements originating from the NTA 8130, or additionally surveyed by a delegation of the Dutch grid operators, are presented in tables. Each requirement is tightly connected to one or more business use cases presented in the document. The ultimate goal of this procedure is to reduce ambiguity of the requirements due to a better understanding of the requirements.
... and pathogen transmission. Because the ultimate object of stem cell research is cell-based clinical therapy, hES cells should ... 4%) Supported by grants (SC12021 and SC11012) from Stem Cell Research...
The added incentive to modify electric use under hourly versus monthly market-based pricing is small for most mass market customers in Upstate New York. If the ultimate policy goal of demand-response programs is to reduce peak load, then promoting conservation measures under monthly market-based pricing holds more promise. (author)
The aim is to provide accurate data on elevation change due to mining activity, via the application of interferometry with ERS SAR data. Ultimately, these elevation changes can then be fed into subsidence models. Interferometry results are presented showing initial evidence of subsidence occurring within the 35 day repeat orbit period of the ERS satellites. The result of extending the monitoring period beyond 35 days is also shown.
The cross section database for electron impact excitation and electron impact ionization for hydrogen beam kinetic energies greater than 100 eV was considered, giving for each particular process a reference to a recommended publication of cross sections, as well as the accuracy or estimated accuracy. The work is motivated by the application of neutral beam injection in magnetic confinement devices, such as large tokamaks. 9 refs, 2 figs.
Table of Contents: Executive Summary; Introduction; Data Sources; Industry Profile and Economic Baseline; Industry Compliance Costs; Industry Impacts; Additional Economic Impacts; Cost-Effectiveness; Environmental Impacts and Benefits; Social Costs and Be...
The bibliography contains citations concerning the use of dialysis in the treatment of wastewaters. Techniques for the removal of metals, ammonia, waste acids, nitrates, and phosphates are described. Special attention is given to the desalination of liquid wastes. Applications of this technology to the treatment of effluent from the agrochemical, petrochemical, tanning, and electroplating industries are discussed. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)
This work has analyzed the key variables of indentation tip radius, contact radius, delamination radius, residual stress and superlayer/film/interlayer properties on nanoindentation measurements of adhesion. The goal to connect practical works of adhesion for very thin films to true works of adhesion has been achieved. A review of this work titled ''Interfacial toughness measurements of thin metal films,'' which has been submitted to Acta Materialia, is included.
The title composition comprises methanol containing stearic acid, C/sub 6/H/sub 6/, dextrin, phenol, a combustion accelerator (ethylene dichloride, xylene, Al stearate, a compound of acetic acid); a foaming agent; and ether and an antiknocking agent. The respective ignition point and boiling point of example compounds were 15.1-15.6/sup 0/ and 63.8-64.1/sup 0/.
The structure of the title compound, Sr-bearing oxonitridoaluminosilicate (Sr-sialon), contains two types of channels running along the a axis, with the three unique Sr atoms...Full Text Available
The bibliography contains citations concerning the structural properties of sputtered tantalum and tantalum compounds. The preparation of thin film capacitors and resistors is described. The electrical properties of the sputtered films are also included. The influence of the substrate on the properties of the coatings is considered, including adherence of the coating to the substrate, and the effects of impurities on coating integrity. (Contains 250 citations and includes a subject term index and title list.)
The bibliography contains citations concerning the properties of tantalum and tantalum compound films formed by sputtering techniques. Topics include processes, and electrical, magnetic, and dielectric properties of the sputtered films. Tantalum compounds studied include nitrates, oxides, and aluminides. The structural properties of sputtered films are also discussed. (Contains a minimum of 105 citations and includes a subject term index and title list.)
This journal includes all formal reports in the NUREG series prepared by the NRC staff and contractors, as well as proceedings of conferences and workshops. The entries in the compilation are indexed for access by title and abstract, contractor report number, personal author, subject, NRC organization, contractor, and licensed facility.
This journal includes all formal reports in the NUREG series prepared by the NRC staff and contractors, as well as proceedings of conferences and workshops. The entries in the compilation are indexed for access by title and abstract, contractor report number, personal author, subject, NRC organization, contractor, and licensed facility.
Laser flash photolysis studies of tetraphenyl-p-dioxin have led to the characterization of its triplet state. The T-T absorption spectra shows maxima at 350 and 545 nm; the triplet has a lifetime of 535 ns in methanol and can be quenched by di-tert-butyl nitroxide, paraquat dications, oxygen, and di-tert-butyl selenoketone. The interaction of the triplet with oxygen leads to the formation of singlet oxygen which in turn reacts with the title compound to yield benzil.
...Pharmaceutics | Special Issue: Solid Dosage Forms LoginRegister mdpi.com Journals A-Z For Authors About Open Access Policy Title / Keyword Journal all Administrative Sciences Agriculture ...Establishing Differences from Adults Recent Developments and Future Perspectives in Dissolution Testing Solid Dosage Forms The 1st Electronic Conference on Pharmaceutical Science The Progress on Pharmaceutics ... 1 (2009) Special Issue \\
This annual report presents an overview of the work performed by the PSI research departments including information on new developments connected with the various accelerators and on the status of the Swiss Light Source project (SLS). Details on the organizational and financial structure of the Institute are also provided This annual report is also available in German under the title `PSI Jahresbericht 1998; Allgemeiner Teil`.figs.
This book contains 49 chapters. Some of the titles are: Molecular, Genetic, and Clinical Aspects of the HLA System; The Normal Immune Response; Significance of the ABO Antigen System; The Role of Dialysis in the Management of End-Stage Renal Disease; Access for Dialysis; Patient Selection for Renal Transplantation; The Living Donor in Kidney Transplantation; and Kidney Preservation by Cold Storage.
Middleware deployed to help TCP performance over links with large ... Boeing Connex (Ku-Band); INMARSAT Swift 64; TrackNet" 2.0 (Ku-Band); G2.5/G3/G4. General ... Incremental deployment may be difficult; High Link budgets; Link Delay ...
The bibliography contains citations concerning industrial uses and design of microwave heating equipment. Included are heating and drying of paper, industrial process heat, vulcanization, textile processing, metallurgical heat for sintering and ceramic manufacturing, food processing, and curing of polymers.(Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)
French ... Title Synthese d'agregats metalliques par radiolyse de solutions aqueuses de sels simples ou complexes. Etude par M. E. du greffage des agregats sur membranes de carbone.
The bibliography contains citations concerning Federal and state laws and management programs for the protection and use of inland wetlands. Utilization of wetlands to control highway runoff and community wastewater is discussed. Wetlands protection programs, restoration projects, resource planning, and wetlands identification methods are cited. References to coastal and salt water wetlands are not included in this bibliography. (Contains 250 citations and includes a subject term index and title list.)
This bibliography contains citations concerning the migration of food-packaging materials into foods. Plastic, glass, cardboard, metal, and ceramic containers are discussed. Techniques for analyzing packaging contamination are included. (Contains 90 citations fully indexed and including a title list.).
The bibliography contains citations concerning the research and development of the electric automobile. Various sources of energy to accommodate electric cars, environmental effects, energy consumption and efficiency, and computer simulation and modeling relative to electric vehicle transportation are considered. Design variations are also included. (Contains a minimum of 195 citations and includes a subject term index and title list.)
The bibliography contains citations concerning the research and development of the electric automobile. Various sources of energy to accommodate electric cars, environmental effects, energy consumption and efficiency, and computer simulation and modeling relative to electric vehicle transportation are considered. Design variations are also included. (Contains a minimum of 121 citations and includes a subject term index and title list.)
The basic principles of determination of the ash content of coal by the title methods are outlined. A brief technical characteristic of the ash meters and radionuclide X-ray fluorescence analyzers manufactured by the PAR company is presented. (Z.S.). 4 figs., 7 refs.
A total of nine papers were presented at the course with the following titles: peat accumulation and coal basins; coal composition; coal quality; sedimentary environments of coal; generation, storage and migration of natural gas in coal bed reservoirs; geophysical log interpretation; the Ardley coal zone of central Alberta; stratigraphy and sedimentary environment of the Coalspur Formation; and the coal-bearing Luscar Group of western Alberta. All of these papers have been abstracted separately.
The answer to the title is ''NO''. The authors investigate the low energy particle spectra of type-II superstring theory after compactification to 4 dimensional space-time by means of the super Kac-Moody algebra as well as the twisted super Kac-Moody algebra. They show that there is no solution containing all of the particle contents in the standard model.
Literature references related to definition, generation, and use of evaluated cross section uncertainty (variance-covariance) files are listed with comments intended primarily to guide the reader toward materials of immediate interest. Papers are also cited that cover covariance information for individual experiments and that relate to production and use of multigroup covariance matrices. Titles are divided among several major categories.
This book contains 18 selections. Some of the titles are: Labelling of amphetamines with /sup 123/I: Receptors for amphetamines; New amphetamine derivatives; Potential new approaches for the development of brain imaging agents for single-photon applications; and IM SPECT with the pinhole collimator.
This book contains 18 selections. Some of the titles are: Labelling of amphetamines with /sup 123/I: Receptors for amphetamines; New amphetamine derivatives; Potential new approaches for the development of brain imaging agents for single-photon applications; and IM SPECT with the pinhole collimator.
This book contains nine selections. Some of the titles are: High Heat-Flux, Forced-Convection Heat Transfer for Tubes with Twisted-Tape Inserts; Heat Transfer Augmentation by Interrupted Surfaces - Experimental Consideration; Turbulent Flow Heat Transfer from Externally Roughened Tubes in Axial Flow in Concentric Pipe Heat Exchangers; and Heat Transfer Enhancement of Turbulent Flow in Pipes with an Internal Circular Rib.
This book contains nine selections. Some of the titles are: High Heat-Flux, Forced-Convection Heat Transfer for Tubes with Twisted-Tape Inserts; Heat Transfer Augmentation by Interrupted Surfaces - Experimental Consideration; Turbulent Flow Heat Transfer from Externally Roughened Tubes in Axial Flow in Concentric Pipe Heat Exchangers; and Heat Transfer Enhancement of Turbulent Flow in Pipes with an Internal Circular Rib.
The title refers to the area of research which studies infinite groups using measure-theoretic tools, and studies the restrictions that group structure imposes on ergodic theory of their actions. The paper is a survey of recent developments focused on the notion of Measure Equivalence between groups, and Orbit Equivalence between group actions. We discuss known invariants and classification results (rigidity) in both areas.
A separation phenomenon occurring during the Charpy impact test of API X80 pipeline steels was investigated in the present study. A detailed microstructural analysis of fractured impact specimens showed that the band structure of bainite elongated along the rolling direction worked as prior initiation sites for separations, and that the number and length of the separations increased with the increasing volume fraction of bainite. In the steels having high work hardenability, tearing-shaped separations were found because the hammer-impacted region was seriously hardened during the impact test, which led to the reduction in the impact toughness. As the test temperature decreased, the tendency toward separations increased, but separations were not found when the cleavage fracture prevailed at very low temperatures. These findings suggested that the formation of bainite and secondary ...
Technologies and practices that recover energy and materials from municipal solid waste present a technically and economically viable alternative to sanitary landfills and other solid waste disposal methods. However, community planners considering resource recovery should be aware of the potential environmental impacts of proposed projects. To assess these impacts, a planner should: identify the most significant types of impacts; establish boundaries beyond which impacts are not significant; characterize the environment as it would exist without the proposed project over the project's lifetime; predict the magnitude, and the distribution over time and space, of potential impacts; and relate the magnitude of predicted impacts to a scale of significance that will allow environmental values to be considered in decision-making. 24 references, 1 table.
The Integrated Status and Effectiveness Monitoring Program (ISEMP - BPA project No.2003-0017) has been created as a cost effective means of developing protocols and new technologies, novel indicators, sample designs, analytical, data management and communication tools and skills, and restoration experiments that support the development of a region-wide Research, Monitoring and Evaluation (RME) program to assess the status of anadromous salmonid populations, their tributary habitat and restoration and management actions. The most straightforward approach to developing a regional-scale monitoring and evaluation program would be to increase standardization among status and trend monitoring programs. However, the diversity of species and their habitat, as well as the overwhelming uncertainty surrounding indicators, metrics, and data interpretation methods, requires the testing of multiple approaches. Thus, the approach ISEMP has adopted is to develop a broad template that may differ in the ...
In accordance with the Department of Energy`s National Environmental Policy Act implementing procedures in Volume 10 of the Code of Federal Regulations, Section 1021,312, the Environmental Restoration and Waste Management Programmatic Environmental Impact Statement Implementation Plan has two primary purposes: to provide guidance for the preparation of the Programmatic Environmental Impact Statement and to record the issues resulting from the scoping and the extended public participation process. The Implementation Plan identifies and discusses the following: background of Environmental Restoration and Waste Management activities, the purpose of the Programmatic Environmental Impact Statement, and the relationship of the Programmatic Environmental Impact Statement to other Departmental initiatives (Chapter 1); need and purposes for action (Chapter 2); scoping process and results of the public ...
An experimental and computational study was undertaken to estimate the effects of pipe rupture and induced pipe whip impact on surround structures considered either as rigid or deformative such as concrete slabs. This program included sixteen tests using 3 inch schedule 80 (or 10) pipes made of carbon steel similar to A106 grade B. The study consisted of tests on rigid target and on concrete slab. The investigation of whip phase and impact phase was done separately for each test. For pipe impact on rigid targets, the impact forces are found to be directly related to the crush strength of the pipe and the general pipe deformation following the impact. For pipe impact on concrete slabs, the response of the target to the pipe impact needs to take into account the local effect such as penetration and localized damage on the slab. The test matrix ...
The impact properties of high-strength low alloy TRIP steels such as 'TRIP-aided dual-phase steel' and 'TRIP-aided bainitic steel' associated with the transformation-induced plasticity (TRIP) of retained austenite were investigated for some applications to the automotive impact members. The TRIP steels possessed far higher impact absorbed value and lower ductile-brittle transition temperature than the conventional ferrite-martensite and ferrite-pearlite steels. The stress relaxation resulting from the strain-induced transformation of retained austenite islands or films improved the impact properties in terms of suppressing void and/or crack initiation and these propagation. The best impact properties were completed in the steel composing of uniform fine bainitic lath structure and a large amount of stable interlath retained austenite films. ...
This economic impact analysis (EIA) examines compliance costs and economic impacts resulting from the U.S. Environmental Protection Agency`s (EPA`s) proposed revisions to effluent limitations guidelines and standards for the Coastal Subcategory of the U.S. oil and gas industry. The EIA estimates economic impacts in terms of annualized costs; production losses; and changes in equity, working capital, and other indicators of financial health at the firm level. In addition, impacts on employment and affected communities, foreign trade, and new sources are considered. A Regulatory Flexibility Analysis detailing the impacts on small businesses within the coastal oil and gas industry also is included in the EIA.
Three complementary impact welding technologies are described in this paper. They are explosive welding, magnetic pulse welding, and laser impact welding, which have been used to provide metallurgical bonds between both similar and dissimilar metal pairs. They share the physical principle that general impact-driven welding can be carried out by oblique impact but are used at different length scales from meters to sub-millimeter. The different length scales require different kinds of systems to drive the process, and the scales themselves can give different weld morphologies. Metallographic analysis on cross-sections shows a wavy interface morphology which is likely the result of an instability associated with jetting, which scours the surfaces clean during impact. The normalized period and...
In order to simplify the coke manufacturing process, a coke production mechanism in coal pyrolysis was discussed. Australian bituminous coal which can produce good coke was used for the discussion. At a temperature raising rate of 50{degree}C per minute, coal weight loss increases monotonously. However, in the case of 3{degree}C, the weight loss reaches a peak at a maximum ultimate temperature of about 550{degree}C. The reaction mechanism varies with the temperature raising rates, and in the case of 50{degree}C per minute, volatiles other than CO2 and propane increased. Weight loss of coal at 3{degree}C per minute was caused mainly by methane production at 550{degree}C or lower. When the temperature is raised to 600{degree}C, tar and CO2 increased, and so did the weight loss. Anisotropy was discerned in almost of all coke particles at 450{degree}C, and the anisotropy became remarkable with increase in the maximum ultimate temperature. Coke and ...
The ultimate compressive strength and modulus of elasticity of femoral cortical bone from adult geese (Anser anser), were determined by sex and by quadrant by compressing small right circular cylinders which were 2.4 mm in height and 0.8 mm in diameter. The average ultimate compressive strength was 183 +/- 29 MPa. The average modulus of elasticity was 13.2 +/- 3.4 GPa. The bending strength and bending modulus of elasticity were determined by a three point bend test on rectangular prisms which had the approximate dimensions 0.75 mm X 0.75 mm X 25 mm. The average bending strength was 263 +/- 44 MPa while the average bending modulus was 19.6 +/- 3.1 GPa. The calcium content was determined by atomic absorption spectrophotometry and no correlation was found with the mechanical properties. The histology of the cortical bone was examined both quantitatively and qualitatively. A unique type of Haversian bone is described. Goose bone was found to be ...
Results from ultimate analysis, proximate and petrographic analyses of a wide range of Kentucky coal samples were used to predict coal rank parameters (vitrinite maximum reflectance (R{sub max}) and gross calorific value (GCV)) using multivariable regression and artificial neural network (ANN) methods. Volatile matter, carbon, total sulfur, hydrogen and oxygen were used to predict both R{sub max} and GCV by regression and ANN. Multivariable regression equations to predict R{sub max} and GCV showed R{sup 2} = 0.77 and 0.69, respectively. Results from the ANN method with a 2-5-4-2 arrangement that simultaneously predicts GCV and R{sub max} showed R{sup 2} values of 0.84 and 0.90, respectively, for an independent test data set. The artificial neural network method can be appropriately used to predict R{sub max} and GCV when regression results do not have high accuracy. (author)
Relationships of ultimate and proximate analysis of 4540 US coal samples from 25 states with gross calorific value (GCV) have been investigated by regression and artificial neural networks (ANNs) methods. Three set of inputs: (a) volatile matter, ash and moisture (b) C, H, N, O, S and ash (c) C, H{sub exclusive} {sub of} {sub moisture}, N, O{sub exclusive} {sub of} {sub moisture}, S, moisture and ash were used for the prediction of GCV by regression and ANNs. The multivariable regression studies have shown that the model (c) is the most suitable estimator of GCV. Running of the best arranged ANNs structures for the models (a) to (c) and assessment of errors have shown that the ANNs are not better or much different from regression, as a common and understood technique, in the prediction of uncomplicated relationships between proximate and ultimate analysis and coal GCV. (author)
The effects of key metallurgical variables on the low fluence hardening in a set of A533B model steels were evaluated over a wide range of irradiation temperatures. Above about 163 degrees C hardening increased with higher copper and nickel contents, as is typical of the pressure vessel operating regime around 290 degrees C. However, at 121 degrees C the hardening was generally lower and unaffected by copper and nickel variations. This observation of decreased hardening with lower temperature (e.g. an open-quotes invertedclose quotes temperature dependence) is tentatively attributed to a reduced contribution of copper precipitation. Tensile data for a set of commercial steels with a range of (uncontrolled) compositions also showed minimal sensitivity to copper variations at 121 degrees C. Unlike the hardness data no systematic reductions in the yield stress increases were observed between 163 and 121 degrees C. However, the ultimate tensile strength did decrease at ...
ObjectivesThe aim of this study was to evaluate the relationship between micro-tensile bond strength (mTBS) and ultimate tensile strength (UTS) of resin composite restorations in cavities filled by a bulk or incremental technique using the micro-tensile test.MethodsClass I cavities (4mm long, 3mm wide, 3mm deep) were prepared into dentine of sixteen human molars. All cavities were bonded with Clearfil SE Bond and restored with AP-X composite with either a bulk or incremental technique. After storage in water for 24h, the teeth were vertically sectioned to yield two slabs. Each slab was sectioned into three sticks. Sticks of one slab were trimmed into an hourglass of 0.7mm2 area at resin-dentine interface for bond strength measurement while the other sticks were trimmed at the centre of the...
A detection theory is developed for point-contact metal-oxide-metal (MOM) systems. A system with heterogeneous oxide strongly bonded to the substrate is considered. It is shown that the form of the functional connection between the barrier heights and the ultimate compressive strength of the oxide has no substantial influence on the voltage-current characteristics of the system. Quantitative analysis indicates that a MOM system can behave as a tunnel diode and as a diode with a Schottky barrier. The model permits the determination of the optimum construction of long-life detectors based on MOM point-contacts.-
The bone mineral areal content and the ultimate compressive strength were determined in 109 lumbar vertebrae from 36 subjects. The bone mineral areal content was related to the number, shape, and localization of the Schmorl's nodes detected in the x-rayed and sectioned vertebral bodies. One type of node, irregular in shape and localization, occurred only in the vertebrae with low bone mineral areal content values and thus in vertebrae with relatively low compressive strength. A second type of Schmorl's nodes, regular in shape and localization, did not reflect any general weakness of the vertebral bodies. PMID:6623194
Strain rate effects for the high strength, metastable beta-titanium alloy Ti-8Mo-8V-2Fe-3Al are assessed in terms of tensile and fracture toughness behavior. It is shown that as the strain rate increases the yield strength, ultimate tensile strength, and ductility also increase. As a result of the decrease in the amount of intergranular fracture as the strain rate is increased, the dynamic fracture toughness values K/sub Id/ are greater than those obtained under static conditions as given by K/sub Q/.
The ultimate compressive strength of 36 thoracolumbar vertebrae was determined experimentally. In addition, the trabecular bone mineral content was measured by single energy quantitative computed tomography. The areas of fractured endplates were also determined by computed tomography. The results show that a linear relationship exists between the compressive strength and the product of bone density and endplate area. These data allow an in vivo prediction of vertebral body strength using a noninvasive method with a standard error of estimate amounting to less than 0.95 kN. PMID:3212488
The 'elementary' particle physics began in 1935, when Hideki Yukawa published his pioneering pi-meson theory, and the problem of strong interaction was finally solved 40 years later by the establishment of the Standard Model. The composite models of hadrons by the Sakata school and Sin-itiro Tomonaga's renormalization theory for quantum electrodynamics played essential roles for finding this beautiful solution. It is really surprising that it took only 40 years to solve such desperately difficult problem. The 'elementary' particle physics then split into two new fields, quark-hadron physics' and 'unified (ultimate) theory of particle physics', which are now 30 years old already. (author)
The viability of osteocytes can be demonstrated in sawn decalcified sections of bone by their lactate dehydrogenase activity. In the cancellous bone of the femoral head, the proportion of lacunae containing viable osteocytes decreased from 88 +/- 7% (mean +/- SD) at 10-29 years to 58 +/- 12% (P Ultimate compressive strength did not correlate with osteocyte viability. In the femoral head there is gradual, age-related reduction in osteocyte viability that can be more pronounced in hip fracture. Osteocyte death may affect bone quality by impairing repair of fatigue damage. PMID:8275364
In source coding, either with or without side information at the decoder, the ultimate performance can be achieved by means of random binning. Structured binning into cosets of performing channel codes has been successfully employed in practical applications. In this letter it is formally shown that various convolutional- and turbo-syndrome decoding algorithms proposed in literature lead in fact to the same estimate. An equivalent implementation is also delineated by directly tackling syndrome decoding as a maximum a posteriori probability problem and solving it by means of iterative message-passing. This solution takes advantage of the exact same structures and algorithms used by the conventional channel decoder for the code according to which the syndrome is formed.
The transfer of fish from field to laboratory facilities or their propagation in closed or restricted systems frequently results in bacterial infection and ultimately large-scale mortality. In attemps to alleviate this problem, we have added tetracycline hydrochloride to the water prophylactically (pretreating tanks before wild fish were added) and therapeutically (treating tanks after bacterial outbreaks were detected.) In the present study, we examined the effect of tetracyline hydrochloride on the critical thermal maximum (CTM) of the common shiner (Notropis cornutus).
In the quest to understand the ultimate nature of WIMPs, we propose the use of a hybrid detection technique: cylinders filled with liquefied noble gasses, acting as targets, are immersed inside a tank of Gd-doped ultra-pure water that provides an active and efficient veto against neutrons. The evaluation of the background rejection capabilities and physics potential of this instrument have been carried out through a full GEANT4 simulation, assuming the detector will be located at the Canfranc underground laboratory (in the Spanish Pyrenees). Our results compare very favourably with existing or planned experiments in the field. This technique is scalable and will allow to reach target masses of few tonnes in the next future.
This essay, operating in a philosophical mode, continues and expands the discussion initiated by Amos Yong about the role of "spirit" in the theology-science dialogue. After a working definition, it explores Santayana's and Tillich's perspectives on the proximate derivation of human spirit before treating them further as representatives for naturalist and trans-naturalist camps regarding the spirit's ultimate source. Then a descriptive definition of "spirit" is advanced along with the concluding standpoint that while "spirit" is vague, even poetic, it remains for the foreseeable future a necessary and useful placeholder for what advances in neuroscience and future philosophical and theological research can help us unveil further.
Due mainly to competitive pressures, the practice of offering electric and telephone service under contracts or special tariffs negotiated individually between a utility and its customers has increased in importance in recent years. Moreover, the practice is likely to become still more widespread in the future. This creates questions of public policy that are of interest to regulators and ratepayers alike such as how to supervise the practice, how to encourage utilities to compete while preventing cross-subsidization and anticompetitive behavior, and how the practice will ultimately affect utilities and ratepayers. This report sheds light on the topic by describing approaches that have been taken by the various regulatory commissions and by providing a framework for analyzing such contractors.
Marburg virus belongs to the genus Marburgvirus in the family Filoviridae and causes a severe hemorrhagic fever, known as Marburg hemorrhagic fever (MHF), in both humans and nonhuman primates. Similar to the more widely known Ebola hemorrhagic fever, MHF is characterized by systemic viral replication, immunosuppression and abnormal inflammatory responses. These pathological features of the disease contribute to a number of systemic dysfunctions including hemorrhages, edema, coagulation abnormalities and, ultimately, multiorgan failure and shock, often resulting in death. A detailed understanding of the pathological processes that lead to this devastating disease remains elusive, a fact that contributes to the lack of licensed vaccines or effective therapeutics. This article will review the...
The theoretical alignment limit for focused ion beam (FIB) implantation was deduced from the calculated resolution for the detection of an alignment mark. The alignment resolution varies with the signal to noise ratio and there is an optimum current which gives the best resolution. The alignment resolution epsilon/sub sigma/ is approximately 0.006 ..mu..m for a 160 keV Si/sup ++/ beam from our FIB implanter. The measured alignment error is approximately 0.06 ..mu..m and the main reason of this discrepancy is vibration. The ultimate limit on the alignment error can be reached through improvements in the implanter system.
The Kootenay, Luscar/Manville, and Belly River Groups, and the Horseshoe Canyon and Scollard Coalspur Formations are the most important coal measures in Alberta. Estimated current resources and reserves are 89 and 35 billion tonnes, respectively. Ultimate resources and reserves are 2100 and 660 billion tonnes, respectively. Most of the reserves are subbituminous and require underground mining methods. Current production is approximately 39 million tonnes per year, primarily subbituminous coal that is used for domestic electrical generation. Bituminous coal is exported. Long-term development will depend on markets, price, and infrastructure. 11 refs., 4 figs.
The report is the second of three describing the geology of coal quality variations in the foothills and mountains region of Alberta. The Lower Cretaceous Luscar Group, Lower Paleocene Coalspur Formation, and the Upper Paleocene Paskapoo Formation (Obed-Marsh coal zone, which is classified as a foothills deposit) are evaluated. Data on proximate and ultimate analysis variables, calorific analysis, vitrinite reflectance, maceral analyses, and coal quality relationships are presented. The coals range from low volatile bituminous to subbituminous A. Regional and local in seam coal quality variations are examined. 49 refs., 39 figs., 6 tabs.
Objective:To evaluate the impact of avoidable mortality on the changes in life expectancy at birth in Spain.Methods:Standard life table techniques...Full Text Available
IntroductionMale sexual dysfunction is a common complication of diabetes (DM), but the relative impact of erectile dysfunction (ED), orgasmic dysfunction (OD), and/or...Full Text Available
We successfully reproduce one of the French pipe whip experiments with the computer code WIPS. The WIPS results are in excellent agreement with the experimental data and the French computer code TEDEL. This justifies the use of its pipe element in conjunction with its U-bar element in a simplified method of impact analyses.
The impact of introducing a 3,6,9-trioxadecyloxyl group at various positions of the desazadesferrithiocin (DADFT) aromatic ring on iron clearance and organ distribution is described. Three DADFT...Full Text Available
BackgroundHelminth infections can alter susceptibility to malaria. Studies need to determine whether or not deworming programs can impact on Plasmodium infections...Full Text Available
The paper presents a review of the current state of knowledge on the likely impacts of extreme weather and climate events on coastal zones and small islands in the context of climate change. Possible response options, including prevention, preparedness and adaptation, are indicated.
PURPOSE This study was designed to evaluate the impact of electronic medical record (EMR) implementation on quality of diabetes care.METHODS We conducted a 5-year longitudinal...Full Text Available
This study investigated the impact of lifelong sedentariness on skeletal muscle mass and mitochondrial function. Thirty C57BL/6 strain mice (2 months) were randomly divided into three groups (young-Y;...Full Text Available
Objectives:Despite its impact on health policy, the relationship between geographical proximity and health care seeking has received scant attention in the medical literature. This...Full Text Available
PURPOSE We wanted to assess the impact of an electronic health record–based diabetes clinical decision support system on control of hemoglobin A1c (glycated hemoglobin),...Full Text Available
A collaborative research effort by scientists in several states and in Canada has produced information to develop a formal risk assessment of the impact of Bt corn on monarch butterfly...Full Text Available
Few data exist about the impact of computerized prescribing systems on outpatient medication errors (MEs) and adverse drug events (ADEs). We compared the rates of MEs and ADEs in handwritten sites versus...Full Text Available
ObjectiveTo investigate the impact white matter hyperintensities (WMH) detected on MRI have on motor dysfunction and cognitive impairment in non-demented elderly...Full Text Available
This study explored posttraumatic growth (PTG), positive change resulting from struggling with trauma, among 7- to 10-year-olds impacted by Hurricane Katrina. Analyses focused on child self-system...Full Text Available
The report details the economic impact of two alternative regulatory options; a Treated Discharge Option and a Zero Discharge Option on facilities that would have to comply with the regulations as part of the reproposal of effluent limitations and standar...
This report estimates the economic and financial effects of compliance with the proposed effluent limitations guidelines and standards for the Centralized Waste Treatment (CWT) industry. The Environmental Protection Agency (EPA) has measured these impacts...
Objective: The aim of this study was to investigate the impact of a program of repeated assessments, feedback, and training on the quality of coded clinical data in general practice.Design:...Full Text Available
Section 204 of the Energy Independence and Security Act of 2007 (EISA 2007) requires EPA to assess and report to Congress on the impacts to date and likely future impacts of the increased use of biofuels as required by the Clean Air Act, section 211(0). Environmental issues (...
Twenty-two cases of indigestion occurred in a 650-cow herd. Five cows had severe sand abomasal impaction, diagnosed by laparotomy. The pH of prepartum cows’ urine was < 6.0 and of sand...Full Text Available
ObjectiveThere has been much debate about the value of condoms in HIV/STI programming. This should be informed by evidence about intervention impact on condom use, but there is limited...Full Text Available
The Minami-Iwaki trunk line now under construction by Tokyo Electric Power Company is an UHV transmission line which covers 130km from the central region of the Abukuma highlands, Fukushima Prefecture, through the northern ridge of the Kanto Plain to Imaichi City, Tochigi Prefecture and has 235 steel towers. About 30% of the ground along the above route is mainly layers of sand and gravel. Accordingly it has become urgent to design rationally the pile foundations in the sand and gravel layers. Hence the company has studied an estimation method of the ultimate bearing power of cast-in-place piles penetrating the sand and gravel layers and the displacement of pile heads. In this report, the result of the above study is described. The company has so far used the equations in accordance to the Meyerhof equations for the estimations of the ultimate bearing power and this time, this equations have been examined for its application to the sand and ...
The reconstruction of segmental defect in long bone is a clinical challenge. Multiple surgeries are typically required to restore the structure and function of the affected defect site. In order to overcome this defect a biodegradable bone tissue engineering scaffold is used. This scaffold acts as a carrier of proteins and growth factors, while also supporting the load that the bone would normally sustain, until the natural bone can regenerate in its place. Work was done to optimize an existing solid free-form scaffold design. The goal of the optimization was to increase the porosity of the scaffold while maintaining the strength of a previously-tested prototype design. With this in mind, eight new designs were created. These designs were drawn using CAD software and then through the use of finite element analysis the theoretical ultimate compressive strength of each design was obtained. Each scaffold design was constructed by casting a thermal-curable ...
Los Alamos National Laboratory is subject to annual emissions-reporting requirements for regulated air contaminants under Title 20 of the New Mexico Administrative Code, Chapter 2, Part 73 (20.2.73 NMAC), Notice of Intent and Emissions Inventory Requirements. The applicability of the requirements is based on the Laboratory's potential to emit 100 tons per year of suspended particulate matter, nitrogen oxides, carbon monoxide, sulfur oxides, or volatile organic compounds. For calendar year 2001, the Technical Area 3 steam plant was the primary source of criteria air pollutants from the Laboratory, while research and development activities were the primary source of volatile organic compounds. Emissions of beryllium and aluminum were reported for activities permitted under 20.2.72 NMAC. Hazardous air pollutant emissions from chemical use for research and development activities were also reported.
The visual impact of wind turbines is one of the main factors affecting public acceptance of wind parks. This paper evaluates the visual impact of a wind park in Chania, Crete, using the Spanish method of evaluation. The outcomes are combined with the psychometric testing of the residents by the use of questionnaires and with the values of the Spanish method about various scenarios concerning the size of the wind park (double, half, one wind turbine). The results of the study prove that the quantification of the potential visual impact could minimize this, apparently, main reason that affects public acceptance. (author)
The US Department of Energy, Division of Electric Energy Systems, has undertaken to identify the environmental issues and potential impacts associated with the installation of underground electric power transmission systems. This study reports the results of investigations into the advanced cable technologies being considered for future underground applications, as part of the development oriented research program of the Division of Electric Energy Systems. While the technology involves a high level of sophistication, there are relatively few impacts to the environment that are potentially significant, and of these none are inherently non-mitigable. Route planning, system design, and methods of construction and accident response can be pursued in order to minimize impacts where strict constraints are appropriate.
This study is an evaluation of the potential environmental impacts of contaminated groundwater from the ASARCO metals refining facility adjacent to the ...
... small water or ice particles by impaction ... flight recording; principally the hydrometeor charge unit ... capability of directing aircraft movements by radio ...
This book is divided into the following chapters: the atmospheric boundary layer; atmospheric diffusion; pollutants and their properties; and environmental monitoring and impact.
digital libraries, which was identified as a national challenge in the Information ... The linkages between the many digital libraries and information services are ...
The document published under A/63:46 and titled report of the scientific committee of United Nations for the study of ionizing radiations effects, gives the situation of the fifty sixth session of the committee that stood at Vienna from the 10. to 18. july 2008. In the chapter 3 of this report the writers summarize the strategic planning and the working program of the scientific committee for the period 2009-2013. They note that the committee worry about the inadequate means, particularly in personnel. The priorities for the given period will be the medical exposure of patients, the radiation levels and the effects of energy production, the exposure to natural radiation sources and the improvement of the understanding of the effects of the low doses radiation exposure. (N.C.)
The bibliography contains citations concerning the recycling of scrap plastic produced in the injection molding process. Plastic pellets made from scrap, that are used in the injection molding process, are also discussed. Recycling equipment and automated recycling systems are described. The reuse of plastic scrap culled from junk automobiles and packaging materials is discussed, and waste byproducts from polyurethane production are described. (Contains a minimum of 80 citations and includes a subject term index and title list.)
The bibliography contains citations concerning the recycling of scrap plastic produced in the injection molding process. Plastic pellets made from scrap, that are used in the injection molding process, are also discussed. Recycling equipment and automated recycling systems are described. The reuse of plastic scrap culled from junk automobiles and packaging materials is discussed, and waste byproducts from polyurethane production are described. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)
The author's achievements in the title field are summarized and discussed. The following topics are dealt with: (i) principles of radionuclide X-ray fluorescence analysis; (ii) mathematical methods in X-ray fluorescence analysis; (iii) Ross differential filters; (iv) application of radionuclide X-ray fluorescence analysis in the coal industry (with emphasis on the determination of the ash content, sulfur content, and arsenic content of coal); and (v) evaluation of the X-ray fluorescence analyzer from the radiological safety point of view. (P.A.).
This report is the first revision to ``Radiological Performance Assessment for the E-Area Vaults Disposal Facility, Revision 0'', which was issued in April 1994 and received conditional DOE approval in September 1994. The title of this report has been changed to conform to the current name of the facility. The revision incorporates improved groundwater modeling methodology, which includes a large data base of site specific geotechnical data, and special Analyses on disposal of cement-based wasteforms and naval wastes, issued after publication of Revision 0.
The bibliography contains citations concerning plasma immersion ion implantation (PIII) and equipment. PIII is a new technique to implant plasma ions into materials for surface modification and treatment. Topics include plasma nitriding, semiconductor doping, ion energy distribution, ion dose, pulsed plasma, metal plasma, and defect passivation. References also review applications in semiconductor device and integrated circuit manufacture, silicon material fabrication, aerospace bearings, carbon coatings on metals, and ceramic coatings. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)
The bibliography contains citations concerning the pitting corrosion of copper and copper alloys, in different media, with some references to methods for protecting against such corrosion. Included are factors contributing to the onset of pitting corrosion. Emphasis is placed on exposure to water, especially in tubing for heat exchangers and water conduits. Many of the citations present studies on exposure to sea water. Some references pertain to the detection of pitting corrosion in installations and the evaluation of the degree of pitting present. (Contains 250 citations and includes a subject term index and title list.)
The bibliography contains citations concerning the pitting corrosion of copper and copper alloys by different media, with some references to methods that protect against such corrosion. Included are factors contributing to the onset of pitting corrosion. Emphasis is placed on exposure to water, especially in heat exchanger tubing and water conduits. Studies are included which examine corrosion in metals containing small amonts of copper where corrosion is attributable to changes in alloying. (Contains a minimum of 158 citations and includes a subject term index and title list.)
The Marine Technology Society 1994 conference was held in Washington, D.C., September 7-9, 1994. Titled Challenges and Opportunities in the Marine Environment, the conference offered a wide variety of presentations. State-of-the-art technology, government policies and regulations, and environmental concerns were addressed. Offshore mining, coastal zone management, marine engineering, oceanographic research, educational issues, and global climate change were also well represented in the presentations. The conference proceedings are organized around the daily sessions and roughly 70% of the papers are included.
The book is a German translation of an American textbook with the original title ''MRI Survival Guide'' and is intended to serve as an introductory guide for beginners or a reference book for quick information. Readers will find information on the fundamentals of the technology and methodology of MRI as well as all details of relevance to practice in a precise and easy-to-grasp arrangement, covering all anatomic areas of interest, illustrations and descriptions of characteristic signs of pathologic processes, high-quality and unusually large-sized diagnostic pictures, a modern didactic concept for quick orientation, including surveys, tables, and reproductions for visualisation of contents. (orig./CB)
This bibliography contains citations concerning the control and mitigation of radon pollution in homes and commercial buildings. Citations cover radon transport studies in buildings and soils, remedial action proposals on contaminated buildings, soil venting, building ventilation, sealants, filtration systems, water degassing, reduction of radon sources in building materials, and evaluation of existing radon mitigation programs including their cost effectiveness. Analysis and detection of radon and radon toxicity are covered in separate published bibliographies. (Contains 129 citations fully indexed and including a title list.).
The title invention aims at a vibrations-free running of the flywheel to realize a high speed (18,000-20,000 revolutions per minute). The flywheel consists of a case which holds a central stator, a rotor and two ball-bearings. The ball-bearings have a first radial stiffness and are placed in between the rotor and an upper, respectively lower support bearer. The support bearers are supported on the stator with a second radial stiffness. The top and the bottom of the stator is connected to the case by means of a support with a third stiffness. 6 figs.
This publication, part of the series titled Market Guide for Steam Coal Exports from Appalachia provides information on export markets, contracts, and related matters for producers and others involved in mining, selling, and shipping Appalachian coal to foreign buyers. It also includes information on the financial institutions that provide export finance and how they are used. Senior officers of more than 40 banks ranged from the largest money center bank and a major foreign bank in New York City to small banks in Appalachia.
...BUBL LINK: Computer programming - visual basic BUBL LINK Catalogue of Internet Resources Home | Search | Subject Menus | Countries ...O | P | Q | R | S | T | U | V | W | X | Y | Z Computer programming - visual basic Titles ... Author: Microsoft Subjects: computer programming - visual basic DeweyClass: 005.133 Resource type: software SearchVB....com Subjects: computer programming - visual basic DeweyClass: 005.133 Resource type: index VB Helper Tutorials ...
The current and prospective status of astronomical research in Ukraine is discussed. A brief history of astronomical research in Ukraine is presented and the system organizing scientific activity is described, including astronomy education, institutions and staff, awarding higher degrees/titles, government involvement, budgetary investments and international cooperation. Individuals contributing significantly to the field of astronomy and their accomplishments are mentioned. Major astronomical facilities, their capabilities, and their instrumentation are described. In terms of the number of institutions and personnel engaged in astronomy, and of past accomplishments, Ukraine ranks among major nations of Europe. Current difficulties associated with political, economic and technological changes are addressed and goals for future research activities presented.
The bibliography contains citations concerning the properties, industrial uses and federal regulation of asbestos. The references explore advantages and disadvantages associated with use of industrial robots in areas containing high concentrations of asbestos dust, the use of water as a cutting tool to control the generation of asbestos dust, and governmental policies and attitudes relative to the health and welfare of workers subjected to asbestos. Thermal insulation properties, wear characteristics, high temperature capabilities, use as a reinforcement in composite materials, and asbestos substitutes are included. (Contains a minimum of 69 citations and includes a subject term index and title list.)
...Advances in Chronic Kidney Disease-The purpose of Advances Chronic Kidney Disease is to provide in-depth, scholarly review articles about the care and mana ... Advances in Chronic Kidney Disease - Elsevier Home Products User Resources About Us Support & Contact Elsevier Websites Advanced Product ...Search Browse Journals Advances in Chronic Kidney Disease Advances in Chronic Kidney Disease Additional Information Related Publications Editorial Board Journal Online e- Alert Readers ...year: 6 Tips Title This is my tip content Visit Advances in Chronic Kidney Disease Online! The purpose of Advances Chronic Kidney Disease is ...
This is the introductory paper for eight papers that follow in this issue of Natural Resources Journal that were presented at a symposium on the titled subject. The editor notes that two movements in recent decades have been identified with coastal regions - efforts to conserve natural resources and energy source development - and that profound social, economic, and political ramifications have attended these movements. He further notes that the tensions and demands created by the above two developments proved too much for state and local mechanisms, eventually culminating in the Coastal Zone Management Act of 1972. He then briefly evaluates the focus and success of CZMA and reviews the other papers. 58 references.
The paper discusses the potential environmental impacts associated with the operation of a large, say 350 MWe, gas-fired combined cycle power station. It concludes that if appropriate control methods are introduced at the design stage of the plant, environmental impacts are minimal and can be considered acceptable. (author).
... Producers and their Impacts on Women in Central Java, IndonesiaActions basées sur des scénarios visant à élever ... impact sur les femmes dans le centre de Java, en IndonésieInvestigación-acción basada en...
This study provides information on energy resource development and the efforts of State and local communities in the Rocky Mountain, Appalachian, and coastal regions to deal with the related social and economic impacts. It also provides information on the range of options and resources generally available to States and local communities from local, State, industry, and Federal sources to plan for and mitigate the adverse effects of energy development. Onsite visits and interviews with State, local, and Federal officials and private industry involved in mitigating socioeconomic impacts were made.
Supplement B to the Terra Nova Development Application provides a description of the floating production storage and offloading (FPSO) vessel system selected for the development, a summary of the reasons for selecting the system, and the impact of this selection on the Development Plan, the Benefits Plan, the Environmental Impact Statement and the Socio-Economic Impact Statement. There is also a description of the contractor alliance approach to be used in the Terra Nova Development. Refs., tabs., figs.
A viscoelastically prestressed polymeric matrix composite (VPPMC) is produced by applying tension to polymeric fibres, the tensile load being released prior to moulding the fibres into a matrix. Following matrix solidification, compressive stresses imparted by the viscoelastically strained fibres improve composite tensile, flexural and impact properties. This study focuses on the potential for useful life and impact protection capability by performing Charpy impact tests on nylon 6,6 fibre-polyester resin samples subjected to accelerated ageing. Prior to testing, time-temperature superposition principles were used, the samples being aged by heating to 60degreeC for periods representing a 10-fold increase over previous work. The results demonstrated no deterioration in impact performance ov...
There is now a scientific consensus that current rates of accumulation of greenhouses gases in the atmosphere will result in significant global warming and climate change. These changes are likely to have important impacts on a wide range of human activities and the natural environment. There has now been a considerable weight of literature published on the impacts of global warming, much of it very recent. This report seeks to summarise the important results, to analyse the uncertainties and to make a preliminary analysis of the feasibility of monetarising these environmental costs. The impacts of global warming are divided into ten major categories: agriculture, forests and forestry, terrestrial ecosystems and biodiversity, hydrology and water resources, sea level rise and coastal zones, energy, infrastructure/transport/industry, human health and air quality, oceans, and cryospheric impacts. The ...
Estimates of climate change impacts are plague with uncertainties from many physical, biological, and social-economic processes. Among the urgent research priorities, more comprehensive assessments of impacts that better represent the uncertainties are needed. Here, we develop a new super-ensemble-based probabilistic projection approach to account for the uncertainties from CO2 emission scenarios, climate change scenarios, and biophysical processes in impact assessment model. We demonstrate the approach in addressing the probabilistic changes of maize production in the North China Plain in future. The new process-based general crop model, MCWLA [Tao, F., Yokozawa, M. Zhang, Z., 2009. Modelling the impacts of weather and climate variability on crop productivity over a large area: a new proc...
In order to promote environmental damage monitoring and environmental impacts assessment caused by mining in China, the most significant project that uses advanced Earth Observation technology to assess environmental impacts caused by mining, namely MINEO (assessment and monitoring the environmental impact of mining activities in Europe using advanced Earth Observation technology) was introduced and its enlightenment to China were investigated. It was proposed that an integrated technical framework of monitoring environmental impacts caused by mining be designed, quantitative inversion of biological and environmental parameters from RS data be emphasised, hyperspectral Remote Sensing be applied, RS and GIS be integrated with professional models, multi-object applications of RS be implemented, and related standards and specification be drawn up based on typical case study sites. 23 refs., 1 fig.
The purpose of the study is to analyze the economic impacts that are likely to result from promulgation of the proposed best practicable control technology (BPT), best available technology economically achievable (BAT) and Best Conventional Technology (BCT) effluent limitations and standards on placer mining in the United States. The results of the economic impact analysis will help establish pollution control regulations that are economically achievable. The analysis examines how each of four alternative pollution control technologies affects the financial viability of placer mines in the United States. The impacts examined include reduced profitability, production cutbacks, mine closures, and employment and earning losses, as well as impacts to the local economies.
This paper gives a brief review about the state of knowledge on the distributional aspects of climate change impacts. The paper is largely limited to the distribution of impacts between countries (in Section 2). Although there are virtually no estimates reported in the literature, the distribution of impacts within countries is also important. Impact estimates for different sectors (agriculture, health, sea level rise) provides little guidance for estimating differential impacts within countries. It is even harder to find estimates based on social classes. The paper restricts itself to equity about the consequences of climate change. Equity issues about the consequences of emission reduction are ignored here, but should of course be part of a policy analysis. Equity issues about procedures for decision making are also ignored. The paper is organised as follows. Section 2 reviews ...
Many environmental impact statements (EIS) fail to predict environmental impacts, organize information about those impacts in a concise, logical way, and communicate that information intelligibly. This paper presents a systematic, auxiliary ''language'' for environmental analysis under the National Environmental Policy Act (NEPA), in an attempt to correct this problem. The approach improves communication among disciplinary specialists, between an interdisciplinary team and a decision-maker, and between a federal agency and the general public by helping to identify important issues and impacts, and by reducing time, effort, cost, and paperwork. The basis for the approach is found in the principal aims of the NEPA regulations and other criteria. The interdisciplinary language for environmental analysis consists of a small vocabulary, used in conjuction with a simple ...
Oil and gas resources in the offshore areas of the US constitute a significant portion of US recoverable hydrocarbon resources. The exploration, development and production of these offshore resources in California, however, could have significant air quality implications for coastal air basins. This study was developed to address a problem that frequently arises with offshore air quality assessments. Typically, such assessments are performed for a specific activity scenario (e.g., a Federal OCS Lease Sale involving a projected number of drilling rigs, platforms, pipelines, etc.) and assume a projected (but uncertain) level of recoverable oil and gas resources. This study enables interested parties to estimate air emissions and impacts for a wide range of OCS-related development scenarios. The modular emission calculation procedure and the generic impact assessment provide for maximum flexibility in reassessing the emissions and ...
The influence of material configuration and impact parameters on the damage tolerance characteristics of sandwich composites comprised of carbon-epoxy woven fabric facesheets and Nomex honeycomb cores was investigated using empirically based response surfaces. A series of carefully selected tests were used to isolate the coupled influence of various combinations of the number of facesheet plies, core density, core thickness, impact energy, impactor diameter, and impact velocity on the damage formation and residual strength degradation due to normal impact. The ranges of selected material parameters were typical of those found in common aircraft applications. The diameter of the planar damage area associated with Through Transmission Ultrasonic C-scan measurements and the peak residual facesheet indentation depth were used to describe the extent of internal and detectable surface damage, respectively. ...
A control group of geese (Anser anser) on a normal calcium diet for egg laying poultry was compared to egg laying geese on a calcium deficient diet. The ultimate compressive strength and modulus of elasticity of femoral cortical bone from each group were determined by compressing right circular cylinders which were 2.4 mm in height and 0.8 mm in diameter. The bending strength and bending modulus of elasticity of tibial cortical bone were determined by three point bend tests on rectangular prisms which were approximately 25 mm by 0.8 mm by 0.8 mm. Bone calcium content and eggshell calcium content were determined by atomic absorption spectrophotometry. Blood samples were analyzed for free calcium ion concentration. Histological observations included studies of cross-sectional microradiographs, examinations of cross sections stained by a modified Masson's technique, and a determination of fractional area of voids by quantitative microscopy. The average compressive ...
EPRI has sponsored an experimental program in the pipe whip impact and pipe rupture and depressurization areas. Sixteen pipe whip tests were performed with 3 in Schedule 80 (or 10) carbon steel pipes impacting on rigid target or concrete slab. The major testing parameters include distance, impact location, pipe rupture location, and concrete slab thickness and strength. The piping crushing at impact correlates with impact force and target response behavior. Conservatism was established by comparing measured and calculated impact forces. The pipe rupture and depressurization tests were carried out using 6 in stainless steel and carbon steel pipes under either PWR or BWR fluid conditions. These tests are of axial crack with initial machined-in surface flaw. It was found that pipe rupture would occur only if a long unstable through-wall crack was embedded in a ...
The current situation in the development of nuclear power in the world and in Czechoslovakia is briefly outlined and the possibilities are discussed of alternative energy resources. The environmental impact is described of conventional power plants firing coal; sulphur and nitrogen oxides are mentioned and their environmental impacts shown. Their quantities and the quantities of other gaseous, liquid and soid wastes produced by coal power plants are given. Annual estimates are presented of radioactive material emissions; trace amount emissions of toxic metals and their ecological risks are shown. Concern over the increasing concentration of CO_2 in the atmosphere is voiced. For nuclear power plants, the amount of radionuclides in stack emission and of those released into water flows is tabulated. Their effect on the aqueous ecosystem is characterized as is thermal pollution of water flows and the environmental impact of ...
The Loose Parts Monitoring System (LPMS) provides information on the location of a loosened or detached metal impacted onto the inner surface of a primary pressure boundary and on a mass or energy of the impact signal. For the conventional system, it is popular to employ the group delay among the sensors installed within 3 ft range from the impact source in a collection zone as stated in the Reg. Guide 1.133. However, there exist inherent errors for the estimation of the true location of the impact since it is highly dependent on the plant personnel's decision to determine the arrival time differences of the generated wave group among the neighbouring sensors. To overcome this problem in this study, the two-dimensional approach has been proposed and applied to effectively estimate the arrival time differences of the impact signal by using continuous wavelet transform which is one of ...
A new package for the air transport of hazardous materials is currently being developed in the Transportation Systems Department at Sandia National Laboratories. The baseline design has a unique impact limiter which uses layers of aluminum screen wire and aramid cloth fabric. A primary motivation for selecting this unusual combination of materials is the need for the impact limiter to not only limit the amount of load transmitted to the primary container but also remain in place during impact events so that it provides a thermal barrier during a subsequent fire. A series of uniaxial and confined compression tests indicated that the layered material does not behave like other well characterized materials. No existing constitutive models were able to satisfactorily capture the behavior of the layered material; thus, a new plasticity model was developed. The new material model was then used to characterize the response of air ...
The purpose of this hearing was to bring to the public`s attention a better understanding of both the shortcomings as well as the benefits of the existing wetlands regulations programs, policies and regulations. In addition an attempt was made to highlight those areas where there have been problems with restrictive or confusing regulations, time delays, and costs involved. Ultimately, the purpose is to identify areas in the federal regulations, and if necessary in the federal wetlands related laws, that can be amended, so these work better.
Solar cavity receiver plays a dominant role in the light-heat conversion. Its performance can directly affect the efficiency of the whole power generation system. A combined calculation method for evaluating the thermal performance of the solar cavity receiver is raised in this paper. This method couples the Monte-Carlo method, the correlations of the flow boiling heat transfer, and the calculation of air flow field. And this method can ultimately figure out the surface heat flux inside the cavity, the wall temperature of the boiling tubes, and the heat loss of the solar receiver with an iterative solution. With this method, the thermal performance of a solar cavity receiver, a saturated steam receiver, is simulated under different wind environments. The highest wall temperature of the boi...
Parthenogenesis-inducing (PI) Wolbachia belong to a class of intracellular symbionts that distort the offspring sex ratio of their hosts toward a female bias. In many PI Wolbachia-infected species sex ratio distortion has reached its ultimate expression-fixation of infection and all-female populations. This is only possible with thelytokous PI symbionts as they provide an alternative form of reproduction and remove the requirement for males and sexual reproduction. Many populations fixed for PI Wolbachia infection have lost the ability to reproduce sexually, even when cured of the infection. We examine one such population in the species Trichogramma pretiosum. Through a series of backcrossing experiments with an uninfected Trichogramma pretiosum population we were able to show that the gen...
In this study polycrystalline specimens of as-cast DyCu with B2 crystal structure were compressed to different strains at room temperature to test if stress-induced phase transformation and twinning occur during deformation. In these tests DyCu exhibited high ductility with plastic strain as high as 35% and ultimate compressive strength of ~790MPa. X-ray diffraction and transmission electron microscopy (TEM) showed no indications that DyCu had undergone stress-induced phase transformation or twinning. -type dislocations have been observed to play an important role for imparting the ductile behavior. TEM analyses showed the presence of second phases, Dy2O3 and DyCu2 within the DyCu. The mechanisms of ductility and impurity phase formation are discussed.
The texture influence on tensile tests of AZ31, one of the common Mg alloys, has been studied. Starting material was a rectangular extruded bar, which has a strong texture. Due to the preparation of three tensile samples with 0 , 45 , 90 to the extrusion direction, the initial bar texture influences differently on the mechanical behaviour under tensile load. This results in a variation of the yield strength (90 MPa and 175 MPa) the ultimate tensile strength (250 MPa - 278 MPa) and the final texture. Experimental texture analysis was completed by texture simulations using the VPSC-model (visco plastic self-consistent). The good agreement between experimental and simulated pole figures allows the determination of the activated deformation modes related to the initial texture. (orig.)
Purpose - The service-dominant (S-D) logic views supply chains as value co-creation networks. These networks promote knowledge growth amongst network members via resource deployment and coordination. The exchange of knowledge and utilization of operant resources among the network members leads to co-created service offerings and value proposals for the end-users, with the ultimate goal of transforming end-user experiences to perceptions of superior value-in-use. The purpose of this paper is to develop an illustration of the value co-creation concept and use this illustration as guide to examine the research gaps that are yet to be tapped in the area where supply chain networks and S-D logic intersects. Design/methodology/approach - The literature on S-D logic is reviewed and research gaps ...
Drawing upon the cultural risk perspective and writings on risk taking, this paper seeks to develop ideas relating to the effective use of school cyberspace. It is argued that some individuals respond to exaggerated, yet seductive, discourses of online risks by over-blocking, unreasonably restricting students' Internet activity. At the same time, there are sensible, even compelling, motivations for teachers as well as students to use the school Internet to engage in low-level risk taking, fostering excitement, identity construction and networked media literacy. Connecting these seductive pushes and pulls of risk it is ultimately maintained that the fostering of trust through open communication is key in overcoming over-blocking whilst allowing for greater educational gains, realised in part through certain types of low-level risk taking in school cyberspace.
This paper is focused on TLP and Spar technology as applied to floating production applications. In particular, safety considerations as related to classification and certification requirements are addressed. This covers hull structures, marine systems, production facilities and the relevant mooring systems for each platform type from design approval on through construction, installation and ultimately the ongoing maintenance of the platform to acceptable standards throughout its operating life. The experience of the American Bureau of Shipping with these platforms will be utilized in supporting the practical application of classification and regulatory standards to ensure safe operations and concluding that use of such standards in conjunction with an experienced classification society provides a substantial benefit to companies utilizing these technologies. (author)
Aqueous radioactive high-level waste slurries are combined during processing steps that ultimately produce a stable borosilicate glass waste form. Chemically treated waste slurries are combined with each other and with glass frit-water slurries to produce the melter feed. Understanding the evolution of the rheological properties of the slurries is an important aspect of removing and treating the stored waste. To a first approximation, combinations of colloidal waste slurry with {approx}0.1-mm mean diameter glass frit or glass beads act in an analogous matter to slurries of spherical beads in Newtonian liquids. The non-Newtonian rheological properties of the waste slurries without frit, however, add complexity to the hydrodynamic analysis. The use of shear rate dependent apparent viscosities with the modified Einstein equation was used to model the rheological properties of aqueous frit-waste slurries.
A real-time orbit feedback system has been implemented at the Advanced Photon Source in order to meet the stringent orbit stability requirements. The system reduces global orbit motion below 30Hz by a factor of four to below 5{micro}m rms horizontally and 2{micro}m rms vertically. This paper focuses on dynamic orbit stability and describes the all-digital orbit feedback system that has been implemented at the APS. Implementation of the global orbit feedback system is described and its latest performance is presented. Ultimately, the system will provide local feedback at each x-ray source point using installed photon BPMs to measure x-ray beam position and angle directly. Technical challenges associated with local feedback and with dynamics of the associated corrector magnets are described. The unique diagnostic capabilities provided by the APS system are discussed with reference to their use in identifying sources of the underlying orbit motion.
The goal of this three-year project was to improve the production systems in use by steel foundries in the United States. Improvements in the production systems result in less rework, less scrap, and less material handling, all of which would significantly reduce the energy demands of the process. Furthermore, these improvements would allow the companies to be more competitive, more responsive to customers' needs, deliver products with less lead time and require less capital. The ultimate result is a stronger domestic steel casting industry, which uses less energy. A major portion of this research involved the deployment of student researchers at steel foundries, to study their production systems and collect data.
An analysis is made of the basic principles and methods of construction of integrated optical circuits (IOC) for data processing, which are optical waveguide processors in the integrated form. A classification is provided of IOC in accordance with the nature of the input connections to optical components and in accordance with their intended function. An analysis is made of the current status of research and development of analog IOC for handling analog and digital signals, IOC for computing technology, and switching IOC. A detailed analysis is made of IOC with different functions in data processing: spectrum analyzers and correlators, analog-digital converters, circuits for identification of data sets and for encoding of signals, threshold and multistable circuits, logic and arithmetic units, and switching arrays. Descriptions are given of IOC for optically controlled data handling: bistable purely optical logic circuits, multivibrators, flip-flops, and optical transistors. The ...
The existence of multipole components in the dipole and quadrupole magnets is one of the factors limiting the beam stability in the RHIC operations. So, a realistic non-linear model is crucial for understanding the beam behavior and to achieve the ultimate performance in RHIC. A procedure is developed to build a non-linear model using the available multipole component data obtained from measurements of RHIC magnets. We first discuss the measurements performed at different stages of manufacturing of the magnets in relation to their current state in RHIC. We then describe the procedure to implement these measurement data into tracking models, including the implementation of the multipole feed down effect due to the beam orbit offset from the magnet center. Finally, the field quality analysis in the RHIC interaction regions (IR) is presented.
The Department of Energy has issued a Quality Assurance (QA) specification for organizations involved in making a canistered high-level waste form product that is acceptable for storage in a deep geologic federal repository. The logic for the waste form acceptance process is described. In addition to NQA-1 requirements, fourteen supplemental QA requirements have been drafted to fit the waste form production process. A review plan for assuring complicance with the QA specification is provided. Guidelines for preparation of a waste form producer QA program are also presented. It is expected that the QA program description that result will be influential in supporting the acceptybility of the product to OCRWM and for ultimate disposal of the high-level waste in a deep geologic repository. (author) 3 figs., 4 refs.
The Muon Ionization Cooling Experiment (MICE) focusing solenoid magnets focus the muon beam within the MICE cooling channel on a liquid or solid absorber that is within the warm bore of solenoid. The focusing magnet has a warm bore of 470 mm. his magnet consists of two coils 210-mm long that is separated by an aluminum mandrel that is 200 mm long. Each of the coils has its own leads. The coils may be operated in either the non-flip mode (solenoid mode with both coils at the same polarity) or the lip mode (quadrupole focusing mode where both coils are at opposite polarity). This report describes the focusing solenoid magnet design that will be built by the vendor. The progress on the construction of the first of the focusing magnets will also be discussed in this report. Ultimately three of these magnets will be built. These magnets will be cooled using a pair 1.5 W (at 4.2 K) pulse tube coolers.
BARC has organized an international round robin analysis program to carry out the ultimate load capacity assessment of BARC containment (BARCOM) test model. The test model located in BARC facilities Tarapur, is a 1:4 scale representation of 540 MWe pressurized heavy water reactor (PHWR) pre-stressed concrete inner containment structure of Tarapur Atomic Power Station (TAPS) unit 3 and 4. The features of the BARCOM test model and the constitutive data for the pre-test analysis along with the comparison of the results submitted by various participants are described in this pre-test report of the round robin analysis of BARCOM test model
Solid state lasers, particularly neodymium glass systems, have undergone intensive development during the last decade. In this paper, we review solid state laser technology in the context of high-peak-power systems for inertial confinement fusion. Specifically addressed are five major factors: efficiency, wavelength flexibility, average power, system complexity, and cost; these factors today limit broader application of the technology. We conclude that each of these factors can be greatly improved within current fundamental physical limits. We further conclude that the systematic development of new solid state laser madia, both vitreous and crystalline, should ultimately permit the development of wavelength-flexible, very high average power systems with overall efficiencies in the range of 10 to 20%.
The US Department of Energy (DOE) has millions of gallons of high level nuclear waste stored in underground tanks at Hanford, Washington and Savannah River, South Carolina. These tanks will eventually be emptied and decommissioned. This will leave a residue of sludge adhering to the interior tank surfaces that may contaminate groundwaters with radionuclides and RCRA metals. Experimentation on such sludges is both dangerous and prohibitively expensive so there is a great advantage to developing artificial sludges. The US DOE Environmental Management Science Program (EMSP) has funded a program to investigate the feasibility of developing such materials. The following text reports on the success of this program, and suggests that much of the radioisotope inventory left in a tank will not move out into the surrounding environment. Ultimately, such studies may play a significant role in developing safe and cost effective tank closure strategies.
The primary objective of this study is to assess the oil and gas potential of the West Siberian Basin of Russia. The study does not analyze the costs or technology necessary to achieve the estimates of the ultimate recoverable oil and gas. This study uses reservoir data to estimate recoverable oil and gas quantities which were aggregated to the field level. Field totals were summed to a basin total for discovered fields. An estimate of undiscovered oil and gas, from work of the US Geological Survey (USGS), was added to give a total basin resource volume. Recent production decline points out Russia`s need to continue development of its discovered recoverable oil and gas. Continued exploration is required to discover additional oil and gas that remains undiscovered in the basin.
The three tasks were completed during this reporting period. During this quarter, work focused on a local structural analysis of the Table Rock field, greater Green River basin (GGRB) in southwestern Wyoming. The ultimate objective of the local analysis is to apply the techniques developed and demonstrated during earlier phases of the project in the Rulison Field area of the Piceance basin for sweet-spot delineation. The primary goal of this work is to focus in on the Table Rock field area in the northern Washakie basin of the Greater Green River basin in support of Union Pacific Resources and DOE planned horizontal drilling efforts. The work plan for the quarter of April 1, 1998--June 30, 1998 consisted of three tasks: (1) Acquire necessary seismic data and depth-convert, (2) Map major fault geometry and analyze displacement vectors, (3) Develop and initiate a natural fracture prediction study.
During this quarter, work began on the regional structural and geologic analysis of the greater Green River basin (GGRB) in southwestern Wyoming, northwestern Colorado and northeastern Utah. The ultimate objective of the regional analysis is to apply the techniques developed and demonstrated during earlier phases of the project to sweet-spot delineation in a relatively new and underexplored play: tight gas from continuous-type Upper Cretaceous reservoirs of the GGRB. The primary goal of this work is to partition and high-grade the greater Green River basin for exploration efforts in the Cretaceous tight gas play. The work plan for the quarter of January 1, 1998--March 31, 1998 consisted of three tasks: (1) Acquire necessary data and develop base map of study area; (2) Process data for analysis; and (3) Initiate structural study. The first task and second tasks were completed during this reporting period. The third task was initiated and work continues.
The highest equilibrium free-carrier doping concentration possible in a given material is limited by the ''pinning energy'' which shows a remarkable universal alignment in each class of semiconductors. Our first-principles total energy calculations reveal that equilibrium n -type doping is ultimately limited by the spontaneous formation of close-shell acceptor defects: the 3- -charged cation vacancy in AlN, GaN, InP, and GaAs and the 1- -charged DX center in AlAs, AlP, and GaP. This explains the alignment of the pinning energies and predicts the maximum equilibrium doping levels in different materials. (c) 2000 The American Physical Society
Pulse radiolysis was used to examine the nature of the silver species obtained when an aqueous solution containing sequestered Ag"+ ions was reduced by hydrated electrons in the presence of a surfactant macrocyclic crown ether, labeled L, and/or a maltoside surfactant. The initially formed product is the Ag"0(L) species which rapidly loses its ligand (half-life #<=#5 #mu#s) and reacts with another Ag"+(L) ion to form Ag_2"+(L). The latter species decays by a bimolecular process to form the Ag_4"2"+(L)_n species at a faster rate than its ligand free analogue. Ultimately, colloidal metallic silver, (Ag)_n, forms which is stabilized by the surfactant moieties. No long-term stability to the reduced monomolecular species could be obtained.
Over three years ago, the Core Integration team of the National Science Digital Library (NSDL) implemented a digital library based on metadata aggregation using Dublin Core and OAI-PMH. The initial expectation was that such low-barrier technologies would be relatively easy to automate and administer. While this architectural choice permitted rapid deployment of a production NSDL, our three years of experience have contradicted our original expectations of easy automation and low people cost. We have learned that alleged "low-barrier" standards are often harder to deploy than expected. In this paper we report on this experience and comment on the general cost, the functionality, and the ultimate effectiveness of this architecture.
The effect of the coated composite surface of particles on the mechanical properties of the powder bed was investigated. Polyethylene-silica surface composite powder was prepared at several coating ratios with Hybridizer. Various tests on mechanical properties of the powder bed were carried out with the prepared powder, and the following results were obtained: The ultimate tensile strength depends only on the cohesive force between particles, and the contact probability model of composite particles led to good agreement between the experimental and calculated values. The coefficient of internal friction and cohesive shear strength were influenced due to the interlocking effect of the surface roughness of composite particles. The effects of coating particles became small with dynamic properties like angle of repose. It is possible to control the mechanical properties in a step wise fashion by changing the coating ratio of the particles. 10 refs., 11 figs., 4 tabs.
Materials and processing designs for advanced magnesium alloys with fine microstructures and superior properties were established by the combination of the repeated plastic working and the Mg{sub 2}Si synthesis in solid-state. The grain size was less than 1 {mu}m via RPW process due to its severe plastic working on raw powder. The hot extruded magnesium alloys produced in industries showed high ultimate tensile strength, e.g. 420{proportional_to}450 MPa, when employing Mg-Zn-Al-Ca-RE (Rare Earth) alloy coarse powder, having 0.5{proportional_to}2 mm diameter, as input materials. (orig.)
Colon cancer is one of the leading causes of death and a major public health problem in western countries. We examined the isoflavone content of 70% ethanol extract of soy germ (SG) and its apoptotic effect in HT-29 colon cancer cells. Our results showed that the major isoflavones of the SG extract were daidzein and genistein, and it effectively induced apoptosis in HT-29 cancer cells. In addition, nuclear factor-kappa B (NF-kB) expression was reduced in cells treated with the SG extract, which reduced cyclooxygenase-2 (COX-2) and nitric oxide synthase (iNOS) expression. These combined effects ultimately resulted in apoptosis via caspase-3 activation. In addition, daidzein and genistein, the major isoflavones of SG extract, also exerted the apoptotic effect against HT-29 cancer cells. Thes...
Both simulations and recent experiments conducted at the Advanced Photon Source showed that the performance of liquid-nitrogen-cooled single-silicon crystal monochromators can degrade in a very rapid nonlinear fashion as the power and for power density is increased. As a further step towards improving the performance of silicon optics, we propose cooling with liquid helium, which dramatically improves the thermal properties of silicon beyond that of liquid nitrogen and brings the performance of single silicon-crystal-based synchrotrons radiation optics up to the ultimate limit. The benefits of liquid helium cooling as well as some of the associated technical challenges will be discussed, and results of thermal and structural finite elements simulations comparing the performance of silicon monochromators cooled with liquid nitrogen and helium will be given.
0pen ended piles develop internal frictional resistance between the internal soil plug end the pile wall during axial loading. Current pipe pile design practice assumes that the ultimate internal skin friction is of the same order of magnitude as the outer skin friction. This paper describes a series of laboratory pile load tests on instrumented model pipe piles, designed to investigate the development of plug stresses and skin friction along the plug length during pile loading. The piles contain sand columns of various relative densities and of different heights. The soil plugs are loaded to failure under fully drained conditions. The test data indicate that internal skin friction in sand can be substantially higher than assumed in conventional design practice. This finding could lead to significant economical savings on future pipe pile foundations in sand.
The ultimate goal of this research is to generate and apply novel technologies to speed completion and integration of the human genome map and sequence with biomedical problems. To do this, techniques were developed and genome-wide resources generated. This includes a genome-wide Mapped and Integrated BAC/PAC Resource that has been used for gene finding, map completion and anchoring, breakpoint definition and sequencing. In the last period of the grant, the Human Mapped BAC/PAC Resource was also applied to determine regions of human variation and to develop a novel paradigm of primate evolution through to humans. Further, in order to more rapidly evaluate animal models of human disease, a BAC Map of the mouse was generated in collaboration with the MTI Genome Center, Dr. Bruce Birren.
A 46.3-ft-dia 20-degree conical ribbon parachute has been designed to retard a 2200-lb payload delivered at speeds up to 800 KCAS and at altitudes as low as 150 feet above ground level. The parachute uses both Kevlar and nylon materials, some of which were developed specifically for this parachute. The canopy design incorporates a patented construction geometry to minimize stress concentrations. A cluster of three 3.8-ft-dia ribbon parachutes is used to deploy the main parachute in the presence of severe aircraft flow field effects and large payload angles of attack. The results of over 30 full-scale flight tests indicate that fundamental limitations imposed by the dynamics of the air masses inside and behind the canopy determine the ultimate performance of a single large parachute when it is used at a release altitude of 150 ft.
Heat transfer augmentation based on the process intensification concept in heat exchangers and thermal reactors has received much attention in recent years, mainly due to energy efficiency and environmental considerations. The concept consists of the development of novel apparatuses and techniques that, compared to those commonly used today, are expected to bring dramatic improvements in manufacturing and processing, substantially decreasing equipment size, energy consumption, and ultimately resulting in cheaper, sustainable technologies. The objective of this paper was to investigate the heat transfer characteristics of tubular thermal reactor using static mixing technology. Glycerin and water were used as the test fluids and water was used as the heating source. The results for heat transfer rate were strongly influenced by tube geometry and flow conditions.
Orbit correction is now routinely performed at the few-micron level in the Advanced Photon Source (APS) storage ring. Three diagnostics are presently in use to measure and control both AC and DC orbit motions: broad-band turn-by-turn rf beam position monitors (BPMs), narrow-band switched heterodyne receivers, and photoemission-style x-ray beam position monitors. Each type of diagnostic has its own set of systematic error effects that place limits on the ultimate pointing stability of x-ray beams supplied to users at the APS. Limiting sources of beam motion at present are magnet power supply noise, girder vibration, and thermal timescale vacuum chamber and girder motion. This paper will investigate the present limitations on orbit correction, and will delve into the upgrades necessary to achieve true sub-micron beam stability.
The transmission of electrical energy by use of underground cables is increasing. Fault location techniques have certain limitations; incipient fault detection and location would help reduce the maintenance cost of these lines as well as improve the reliability of service. The report discusses some test results related to RF-probing techniques applied to high-voltage transmission lines. The high-frequency losses and attenuation in high-voltage cables places certain ultimate limitations on RF-probing techniques for incipient fault detection. Time-domain reflectrometry methods were employed to assess the RF-transmission properties of high-voltage cables at frequencies as high as 6 GHz. Fast-Fourier-transform deconvolution was used to obtain loss measurements as a function of frequency. The loss mechanisms were identified. The measurement hardware and methods are discussed as well as analysis approach leading to the conclusions.
The article is devoted to results of fine time structure of particle losses in Tevatron with use of fast beam loss monitors (BLM) based on PIN-diodes. An ultimate goal of the new BLMs is to distinguish losses of protons and antiprotons from neighbor bunches with 132 ns bunch spacing in the Tevatron collider upgrade. The devices studied fit well to the goal as they can recognize even seven times closer - 18.9 ns - spaced bunches` losses in the Tevatron fixed target operation regime. We have measured main characteristics of the BLM as well as studied the proton losses over 10 decades of time scale - from dozen of minutes to dozen of nanoseconds. Power spectral density of the losses is compared with spectra of the proton beam motion.
Digital radiography for diagnosis of chest diseases using Fuji Computed Radiography (FCR) was evaluated. The results were as follows; 1. Compared to the conventional chest X-ray films, various types of image enhancement could be made by manipulation of the digital information such as tone conversion, spatial frequency modification etc. 2. Digital radiography lessens the X-ray exposure dose and will ultimately permit speedy transmission of image data from outlying clinics to central processing hospitals. 3. Digital radiographic images are useful in chest X-ray diagnosis especially in mass surveys for lung cancer and in primary care medicine because of its full imaging capability. (author).
The authors propose a method for determining the risk of femoral neck fracture in osteoporotic patients that is not based on densitometric techniques. The method is based on a structural analysis performed by a computer on data taken from a single digital anteroposterior projection of the hip. From the image, the effective cross-sectional area and cross-sectional moment of inertia are computed from attenuation principles. Together with other geometric measurements, these data are used in an engineering analysis to compute the yield strength of the proximal femur, under stress applied through the acetabulum in a one-legged stance. An index of fracture risk based on the ratio of estimated yield strength to body weight is proposed. Ultimately it is expected that this work will allow the clinician to estimate hip fracture risk in osteoporotic patient using widely available existing technology, a goal which has eluded bone density-based methods.
Thirty fattened one humped desert camels were used to examine the effect of season on contractile and metabolic properties of Longissimus thoracis (LT) muscle. Ten camels were slaughtered according to seasons of the year (winter, summer and autumn). Season significantly influenced muscle chemical composition, ultimate pH (pHu) and color. Activities of metabolic enzymes were higher during autumn season compared to summer and winter for phosphofructokinase (+64% compared to both seasons) and for isocitrate dehydrogenase (+35% and +145% in autumn vs. summer and winter, respectively). Quantification of muscle myosin heavy chain isoforms by SDS-PAGE electrophoresis showed only presence of type I and type IIa MyHC in camel muscle and indicated high proportion in winter for type I and in autumn f...
Recent developments in rechargeable Li-ion battery technology include the use of lithium-carbon compounds instead of metallic anodes. Non-graphitizable carbons offer high capacity as the anode material but it's large irreversible capacity must be solved. The ultimate goals of the present work are to understand the origin of the high capacity and large irreversible capacity in conjunction with the structural change due to Li intercalation and thus to establish a scientific basis for optimizing their performance in real batteries. 'House of cards' model is considered and emphasis is given to find out the size of the pores present in the carbon fibers prepared from an isotropic petroleum pitch and heat treated at 1200degC. Small angle neutron scattering and wide angle neutron scattering results provide enlargement of pores and d-spacing of grapheme layers after Li intercalation. (author)
#epsilon#_m(Ce"4"+) values of the ceric-cereus system have been measured and the experimental procedure is described. Both routine titration method and electrochemical measurement were used. Some interference factors, such as ultraviolet, acidity and temperature, were studied as well. The temperature coefficient of #epsilon#_m(Ce"4"+) value in this experiment is about -0.1% degree C"-"1. A statistic analysis was made for 24 experimental values of #epsilon#_m(Ce"4"+) and a Gaussian distribution was found. Ultimately, an average molar extinction coefficient of 553.2 +- 1.3 m"2#centre dot#mol"-"1 was obtained at #approx#320 nm in 0.4 mol/L H_2SO_4 system, with a relative standard deviation of 0.24% (95% confidence level) and a total uncertainty of 1.5%.
Design of pipe whip restraints requires a knowledge of the maximum allowable unsupported pipe length. This paper presents a numerical method for calculating this critical length of the pipe. Salient features of the method are: (1) as a flow rounds an elbow, it exerts a transverse kick and an axial thrust to the pipe, both the axial thrust and the bending moment are considered; (2) the jet force is applied in an abrupt manner, the dynamic amplification factor (DAF) is determined from the load-deflection (H-{Delta}) curve of the pipe, by taking into consideration large strain, large deformation and the nonlinear stress-strain relationship of the piping material; (3) the ultimate capacity of the pipe under the combined action of an axial force and a bending moment is governed by an interaction formula. The maximum unsupported pipe length is calculated from this formula. Only the formulas and derivation are presented. Numerical results and design curves will be given ...
Applied science may once again play a decisive role in changing the face of armed conflict, and the rest of human affairs, by shifting the battlefield to our very brains. The national-security establishment--and particularly the Pentagon's Defense Advanced Research Projects Agency (DARPA)--supports research at the intersection of neuroscience and national security that could ultimately enable authorities to do things like enhance (or muddle, or erase) memory, monitor crowds for individuals whose brain patterns correlate with aggressive behaviors, or control weapons from afar merely with thoughts. What are the dangers of such information falling into "the wrong hands," and are there any "right hands" for this kind of knowledge? Is any extension of human abilities justified by the need for government to protect its society? PMID:15986543
Containment is considered as ultimate safety system and is designed to enclose whole reactor system and prevent the spread of active air-borne fission products. For Pressure and Temperature calculation, Design Basis Accident (Dba) is double ended break of reactor inlet header or main steam line break but activity release studies are done to access its performance following limiting design basis accident i.e. Loss of Coolant Accident (LOCA) and Emergency Core Cooling System (ECCS). In such accident scenario, the core is severely damaged and results in production of steam and hydrogen along with release of activity to containment environment. Containment functions are maintained in such accident, and radiological consequences are within the prescribed limits. (author)
In order to understand the parameters of the standard model of electroweak and strong interactions (coupling constants, masses, mixing angles) one needs to embed the standard model into some larger theory that accounts for the observed values. This means some additional sector is needed that fixes and stabilizes the values of the fundamental constants of nature. In these lecture notes we describe in nontechnical terms how such a sector can be constructed. Our additional sector is based on rapidly fluctuating scalar fields that, although completely deterministic, evolve in the strongest possible chaotic way and exhibit complex behaviour. These chaotic fields generate potentials for moduli fields, which ultimately fix the fundamental parameters. The chaotic dynamics can be physically interpreted in terms of vacuum fluctuations. These vacuum fluctuations are different from those of QED or QCD but coupled with the same moduli fields as QED and QCD are. The vacuum ...
The central engine of Gamma Ray Bursts is hidden from direct probing with photons mainly due to the high densities involved. Inferences on their properties are thus made from their cosmological setting, energetics, low-energy counterparts and variability. If GRBs are powered by hypercritical accretion onto compact objects, on small spatial scales the flow will exhibit fluctuations, which could in principle be reflected in the power output of the central engine and ultimately in the high energy prompt emission. Here we address this issue by characterizing the variability in neutrino cooled accretion flows through local shearing box simulations with magnetic fields, and then convolving them on a global scale with large scale dynamical simulations of accretion disks. The resulting signature is characteristic, and sensitive to the details of the cooling mechanism, providing in principle a discriminant for GRB central engine properties.
Digital topographic models are the foundation of more advanced modeling applications and ultimately inform planning and decision making in many fields. Despite this, the error associated with these models and derived attributes is commonly overlooked. Little attention has been given in the scientific literature to the benefits gained from having less error in a model or to the corresponding cost associated with reducing model error by choosing one product over another. To address these gaps in knowledge we evaluated the error associated with five digital elevation models (DEMs) and derived attributes of slope and aspect relative to the same attributes derived from LiDAR data. We also estimated the acquisition and processing costs per square kilometer of the five test models and the LiDAR m...
How does one assure that both quality and creativity are obtained in basic research environments QA theoreticians have attempted to develop workable definitions of quality, but in more reflective moments, these definitions often fail to capture the deeper essence of the idea of quality.'' This paper asserts that creativity (as a product of the human mind) is a concrete interface between perfunctory definitions of quality (conformance to specifications) and more philosophical speculations about the nature of quality- related ultimates'' like elegance or beauty. In addition, we describe the distinction between creative ideas and creative acts and highlight one of the major inhibitors of creativity, fear. Finally we show that highly creative people often have an irreverent attitude toward boundaries and established authority, and discuss how one can allow for this when designing a QA program in a basic research environment.
This project is concerned with the kinetics and mechanisms of aromatic oxidation and soot and fullerenes formation in flames. The objective of the aromatics oxidation work is to identify and measure the concentration of important intermediates and products in benzene oxidation, and to determine reaction mechanisms and kinetics properties consistent with the behavior seen in flames. The research on soot formation is concerned primarily with the particle inception stages, but the work includes study of soot structure at all stages of growth in order to obtain mechanistic information from evidence of growth steps recorded in the structure of the particles. The ultimate objective is to understand how nascent soot particles are formed from high molecular weight compounds, including the roles of planar and curved PAH and the relationship between soot and fullerenes. The objective of the proposed research on fullerenes is to develop a more comprehensive understanding of ...
This paper deals with steel fiber reinforced concrete mechanical static behaviour and with its classification with respect to fibers content and mix-design variations. A number of experimental tests were conducted to investigate uniaxial compressive strength and tensile strength. Different mixtures were prepared varying both mix-design and fiber length. Fibers content in volume was of 1% and 2%. Mechanical characterization was performed by means of uniaxial compression tests with the aim of deriving the ultimate compressive strength of fiber concrete. Four-point bending tests on notched specimens were carried out to derive the first crack strength and the ductility indexes. The tensile strength of steel fiber reinforced concrete (SFRC) was obtained both from an experimental procedure and b...
{sup 90}Sr, with a long half-life of 28.5 years, is the most dangerous strontium isotope. The adsorption behavior of radionuclides in the environment are closely related to the safe disposal of radioactive wastes. Since various types of minerals may exist in and around the repositories used for ultimate disposal of nuclear waste, the adsorption behavior of certain radionuclides onto and from these minerals and similar adsorbents should be studied in order to estimate the rates of transport of the nuclides in the event of water penetration into and through the repository. Information on the adsorption properties of the purified individual clay minerals may not be sufficient to predict the adsorption properties of a corresponding mixture, because these clay minerals may interact with each other and lead to modification of the adsorption properties of the mixture as compared to the pure minerals. The adsorption behavior of strontium on kaolinite and montmorillonite ...
A ferritic steel with finely dispersed precipitates was investigated to reveal the fundamental strengthening mechanisms. The steel has a yield strength of 760MPa, approximately three times higher than that of conventional Ti-bearing high strength hot-rolled sheet steels, and its ultimate tensile strength reaches 850MPa with an elongation-to-failure value of 18%. Using energy dispersive X-ray spectroscopy (EDXS) and transmission electron microscope (TEM), fine carbides TiC with an average diameter of 10nm were observed in the ferrite matrix of the 0.08%Ti steel, and some cubic M23C6 precipitates were also observed at the grain boundaries and the interior of the grains. The finely dispersed TiC precipitates in the matrix provide matrix strengthening. The estimated magnitude of precipitation ...
Analytical models for predicting the deformation and failure of composite sandwich panels subjected to blast and projectile impact loading are presented in this paper. The analytical predictions of the transient deformations and damage initiation in the composite sandwich panels were compared with finite element solutions using ABAQUS Explicit. For the blast model, the predicted transient deformation of the sandwich panel was within 7%of FEA results, while the predicted damage initiation using Hashin's composite failure criteria was about 15%higher than FEA results in most cases. For the high velocity impact model, the predicted transient deformations were within 20%of FEA results.
Studied are the mechanical properties of welded joints and heat affected zones of the Kh8N10T steel and OT4 and VT1-2 titanium alloys on welding in Ar+deltaF_6 and Ar+CCl_2F_2 mixtures contributed to a decrease of porosity. Tensile and impact tests of welded joints have revealed that additions of sulfur hexafluoride into argon causes a decrease of impact strength in titanium alloy when the tensile strength does not depend on the composition of a halogen-containing atmosphere. Freon (CCl_2F_2) additions decrease only slightly the impact strength of the investigated alloys.