Coal ash is a substance that has been mixed into minerals in the earth`s crust during their coalification process. Estimation was made on what kinds of mineral composition have been mixed into coals. Noted first was the kinds of compounds contained in the ash, wherein the ratios of mass in the compounds and minerals were correlated, and selection was made on minerals which are thought correlated. The selection criterion was based on minerals containing silica, alumina, iron oxide, lime and magnesium as compounds. Then, a phase equilibrium line diagram was used to estimate compositions and melting points of minerals which are thought to have been produced from these compounds. By comparing the estimation with the measured melting points of the ashes, mineral compositions thought reasonable were all selected. Assumption ...
The purpose of the work was to quantitatively characterize temperature effects on the bacterial leaching of sulfide ore material containing several sulfide minerals. The leaching was tested at eight...Full Text Available
The kinetics of oxidation of uranium (IV) monofluoride complex by nitrous acid in nitric acid solution have been studied. The experiments were carried out at constant ionic strength of 2M (HNO_3 and NaNO_3) and temperature in the range of 18-47 deg C. The rate of reaction was determined spectrophotometrically at a wavelength of 621 nm, at which the molar extinction coefficients of UF"3"+ and UF_2"2"+ are the same. It was shown that reaction orders for [HNO_2] and [HNO_3] are equal to 0.12 and 0.39, respectively. The values of activation parameters #DELTA#H"#not =# and #DELTA#S"#not =# are determined to be 83 kJ mol"-"1 and 75 J (mol.K)"-"1, respectively. The rate order of the reaction studied has a weak direct depedence on [H"+] in contrary to the strong and reverse dependence in the absence of fluoride ions. In conclusion, fluoride ions may strongly stabilize the U(IV) in nitric acid solutions. (author) 4 refs.; 3 figs.; 2 tabs.
Mineral carbonation is based on the reaction of carbon dioxide with metal-oxide bearing minerals, usually containing magnesium or calcium silicate, to form hardly soluble carbonates and other solid byproducts. The concept is based on acceleration of the naturally occurring rock weathering process. In the present work the calcium silicate is present in the mineral, wollastonite. To accelerate the process and make it potentially useful for practical applications, mineral carbonation is conducted here using an indirect two-step route in which the reactive component (Ca^2^+ ions in considered case) is first extracted from the mineral matrix and afterwards carbonated. Two solid byproducts are formed in this process: silica in the extraction step and calcium carbonate in the carbonation step. In...
Manganese oxides precipitated from aerated well sea water at the Marine Science Museum, Tokai University, have been analyzed chemically and mineralogically. The O / Mn ratios are lower in todorokite than in birnessite but these minerals have similar contents of minor transition metals, which can be taken up additionally from sea water after the precipitation of Mn oxides. On the basis of these results, the genesis of Mn minerals is discussed in relation to marine Mn nodules.
The generation of acidic mine drainage is based on the oxidation dissolution of sulfide minerals due to the contact of ores with the natural water and the air. Namely, the sulfuric acid promotes the dissolution of sulfide minerals and gangue minerals, and Fe{sup 2+} is further oxidized to turn into Fe{sup 3+}, which acts as an oxidizer for other sulfide minerals and promotes the dissolution of the same. This paper roughly describes a mine drainage treatment focusing on an Fe{sup 2+} neutralization method and an iron bacteria oxidation method. The iron bacteria oxidation method is a method of oxidizing Fe{sup 2+} into Fe{sup 3+} by using iron bacteria, and then removing Fe{sup 3+} with calcium carbonate. This method has been used for treating the drainage in the Sakuhara Mine and ...
The launch of the first spaceborne hyperspectral instrument, Hyperion, in 2000 has provoked further research into its capabilities with regard to mineral exploration. Our study in the remote, mountainous region of Pulang, China employed a two-step progressive approach, first to locate target areas characterized by hydrothermal mineral alteration, using the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER), and secondly, to attempt detailed mineral mapping using Hyperion. The preliminary target detection involved principal components and broad-band spectral analysis and led to the detection of two target areas characterized by argillic alteration, iron-oxide- and sulphate-bearing minerals. A focused hyperspectral study followed using Spectral Angle Mapper (SAM) and Mixt...
Treatment of coal with H/sub 2/O/sub 2/ in presence of formic acid allowed complete destruction of organic matter in 15-72 h (depending on coal rank etc.), giving mineral matter contents in good agreement with those of low temperature ashing (a much slower process.
Discusses results of investigations into catalytic properties of various minerals during hydrogenation of Kansk-Achinsk brown coal with a view to replacing synthetic compositions based on molybdenum. Describes tests and equipment used in hydrogenation of grade B-2 Borodinsk deposit coal in tetralin (hydrogen donor). Various by-products of metallurgical processes and compounds separated from tailings containing mainly iron and sulfur and other metals were used as catalysts. States that: minerals containing iron compounds in the form of pyrites, hematites and magnetites exhibit catalytic properties when used in the hydrogenation of brown coal; pyritic catalysts enrich liquid products with hydrogen while sulfur and nitrogen content remains the same; the yield of malthenes with pyritic catalysts is no lower than with alumocobaltmolybdenum catalysts. 18 refs.
Adduct formation between U(TTA)_4 and several neutral donor (S) was investigated by utilizing the changes in the absorption spectra of U(IV) resulting from the addition of neutral donors to a solution of U(TTA)_4. All the donors used in the present work from 1:1 adducts with U(TTA)_4. From the spectral changes, the equilibrium constants #beta#sub(AB) for the adduct formation reaction viz U(TTA)_4 S reversible U(TTA)_4.S were calculated for a few neutral donors. The log #beta#sub(AB) values obtained in benzene medium, are :TOPO (6.23), TBPO (6.13), TPPO (4.72), DBBP(4.04) TBP(3.04), TIOTP(1.27) and MIBK(-0.10) and a value of 3.98 for TOPO in chloroform medium. The adduct formation was found to result in increasing the coordination number of U(IV) from 8 in U(TTA)_4 to 9 in the adducts it forms with the neutral donors. Similar absorption spectral studies with U(DBM)_4 revealed that it forms much weaker adducts than the corresponding ones with ...
The ruthenium decontamination factor in Purex process falls quickly in successive TBP cycles. So, it is necessary to change the chemical states of RuNO complexes in order to improve DF_R_u in the uranium purification cycle. Hydrazine nitrate is being used to transform RuNO complexes into in-extractable Ru(III)and Ru(IV). However, hydrazine nitrate may be inverted into hydrazoic acid which is dangerous and can bring an unstable factor. Pretreatment using U(IV) solution provides another method to improve the decontamination of ruthenium in Purex process. 0.02 mol/lU(IV) solution can transform RuNO complexes into inextricable species by heating in water bath. The D_R_u can be decreased by a factor of 10-20. U(IV) pretreatment does not bring any harmful chemical in process. The acidity has a very large influence on the effect of pretreatment. The higher the acidity is, the worse the effect will be.
Nineteen fungal strains having an ability to oxidize elemental sulfur in mineral salts medium were isolated from deteriorated sandstones of Angkor monuments. These fungi formed clearing zone on agar medium supplemented with powder sulfur due to the dissolution of sulfur. Representative of the isolates, strain THIF01, was identified as Fusarium solani on the basis of morphological characteristics and phylogenetic analyses. PCR amplification targeting 16S rRNA gene and analyses of full 16S rRNA gene sequence indicated strain THIF01 harbors an endobacterium Bradyrhizobium sp.; however, involvement of the bacterium in the sulfur oxidation is still unclear. Strain THIF01 oxidized elemental sulfur to thiosulfate and then sulfate. Germination of the spores of strain THIF01 was observed in a liqui...
This report reviews the published literature on the anaerobic oxidation of iron in aqueous solutions which are of particular relevance to Swedish granitic groundwaters. The thermodynamics of iron corrosion in water are briefly considered. Following this the experimental data found in the literature are presented and discussed. Results were found for corrosion of iron in both pure water and solutions containing mineral salts. The literature work in the nature of the films formed on iron surfaces under anaerobic conditions is reviewed and the possible mechanisms of film formation are discussed. Conclusions are drawn on the factors most likely to influence and control film growth. 32 refs.
The degradation of chlorinated solvents by reduction at the surface of zero-valent metals and bimetallic systems has emerged as an important approach to the in-situ remediation of ground water. Reduction by iron metal was studied in batch and column systems to develop a mechanistic understanding of the reaction chemistry and to determine the factors that affect dechlorination rate and long term performance in field applications.
Mineral oil based power transmitting fluids, such as automatic transmission fluids, are disclosed which contain 0.05 to 2.0 weight percent of an ester of a thio-bis alkanol and a C/sub 12/-C/sub 50/ hydrocarbon succinic acid or anhydride, the ester being a multifunctional additive providing the properties of friction modification, corrosion inhibition, anti-wear, oxidation inhibition and extreme pressure properties to the fluids.
A renewed interest in chemical fractionation of soil organic matter (SOM) originates from the premise that it enables to isolate labile SOM from SOM protected through mineral binding and recalcitrant SOM. Both selective removal of labile non-bound SOM through oxidation or hydrolysis as well as selective removal of minerals and attached SOM are often applied. Molecular-level SOM characterization by means of temperature resolved Pyrolysis-Field Ionization Mass Spectroscopy analysis (Py-FIMS) was used here as an approach to obtain insight into the fate of SOM upon wet chemical treatment with regard to composition and thermal stability. The applied sequential chemical treatment with 6% NaOCl and 10% HF yielded similar sizes in stable SOM fractions between sandy semi-native heathland and cultiv...
Leptospirillum ferriphilum and Acidithiobacillus caldus are two important acidophilic microorganisms involved in iron and sulfur oxidation during bioleaching. Cell adsorption to mineral surfaces is important for the direct leaching or contact leaching of minerals. In this study, we report the competitive adsorption of binary mixtures of L. ferriphilum LF-104 and A. caldus MTH-04 onto pyrite surfaces. The Langmuir adsorption parameter (CAm) indicated that these two bacteria underwent competitive adsorption to pyrite. Real-time quantitive PCR was used to quantify the relative amounts of L. ferriphilum and A. caldus adsorbed onto the surfaces of pyrite following exposure to a mixture of these two organisms. The adsorption of L. ferriphilum was not affected by A. caldus. However, adsorption of...
Recently, it has become clear that the chemical circumstances under which long-term geological evolution occurs must be properly evaluated in order to develop effective remediation programs for contaminated soil, landfills, radioactive waste repositories, and carbon dioxide capture and storage. The issue of acidic leakage from excavated rock stuck was assessed using a hydro-geochemical simulator, TOUGHREACT. We concluded that in order to properly investigate the phenomenon of acidic leakage from excavated pyrite-containing rock stuck, it is important to obtain accurate information about the following factors: intensity of rainfall, unsaturated flow properties of the excavated rock stuck, specific surfaces for oxidation reaction of pyrite, the species and the quantity of other minerals contained in the rock, and secondary minerals produced. (author)
Adsorptive removal of Pb(II) ions from aqueous solution onto a non-activated charcoal (CC) of oak wood origin was studied in comparison with an activated carbon of coal origin. The adsorption capacity for Pb(II) of the non-activated charcoal increased significantly with deceasing particle diameter, whereas the activated carbon (AC) exhibited approximately constant capacity for Pb(II) adsorption as a function of particle size. Adsorption to the ashes prepared from the non-activated charcoal and the activated carbon was also investigated to examine the role of mineral ash. Although the ash from the activated carbon did not show any Pb(II) adsorption, the ash from the charcoal was very effective for Pb(II) adsorption. Furthermore, Pb(II) was hardly adsorbed when the ash was removed from the non-activated charcoal by acid treatment. Based on the results, the adsorption sites for Pb(II) are considered to be acidic surface functional groups on the external and internal ...
Proposed is a lubricating composition for processing flushing fluids, which contains synthetic fatty acids of the fraction carbon 11-20, oxidized petrolatum, mineral oil, and additives. In order to increase the antiwear, anticorrosion, and antiscratching properties of the composition under conditions of polymineral corrosion with simultaneous decrease in the water loss of the flushing fluids as additives the composition contains stearic acid, polyoxyethylated methyl phenol, naptha soap, 1,5-dibenzoylnapthaline-4', 4''-dicarboxylic acid, calcined soda, secondary nonsaponifiables, obtained in the production of synthetic fatty acids by oxidation of paraffin, and polyfunctional oxygen-bearing compounds, obtained by oxidation of secondary nonsaponifiables by atmospheric oxygen, with the following ratio of components, wt%: 17.2-19.2% synthetic fatty acids of the carbon 17-20 ...
Here we examine Fe speciation within Fe-encrusted biofilms formed during 2-month seafloor incubations of sulfide mineral assemblages at the Main Endeavor Segment of the Juan de Fuca Ridge. The biofilms were distributed heterogeneously across the surface of the incubated sulfide and composed primarily of particles with a twisted stalk morphology resembling those produced by some aerobic Fe-oxidizing microorganisms. Our objectives were to determine the form of biofilm-associated Fe, and identify the sulfide minerals associated with microbial growth. We used micro-focused synchrotron-radiation X-ray fluorescence mapping (mu XRF), X-ray absorption spectroscopy (mu EXAFS), and X-ray diffraction (mu XRD) in conjunction with focused ion beam (FIB) sectioning, and highresolution transmission electron microscopy (HRTEM). The chemical and mineralogical composition of an Fe-encrusted biofilm was queried at different spatial scales, ...
This paper discusses the mineralogy and geochemistry of the No. 6 Coal (Pennsylvanian) in the Junger Coalfield, Ordos Basin, China. The results show that the vitrinite reflectance (0.58%) is lowest and the proportions of inertinite and liptinite (37.4% and 7.1%, respectively) in the No. 6 Coal of the Junger Coalfield are highest among all of the Late Paleozoic coals in the Ordos Basin. The No. 6 Coal may be divided vertically into four sections based on their mineral compositions and elemental concentrations. A high boehmite content (mean 6.1%) was identified in the No. 6 Coal. The minerals associated with the boehmite in the coal include goyazite, rutile, zircon, and Pb-bearing minerals (galena, clausthalite, and selenio-galena). The boehmite is derived from weathered and oxidized bauxite in the weathered crust of the underlying Benxi Formation (Pennsylvanian). A high Pb-bearing ...
The elemental and mineralogical variation in a self-burning coal seam from Coalspur, Alberta, is determined using instrumental neutron activation analysis (INAA) and x-ray diffraction (XRD). The elemental variation in the coal seam is related to temperatures in the various alteration zones, i.e., oxidation, combustion, or carbonization and nature of elements. Mobilization of elements is greatest for As, Br, Cl, Mo, N, S, and Sb. Some of these elements are released to the atmosphere, as evident by the presence of orthorombic sulfur crystals on the surface or in vents at the top of the burning seam or saturation of oxidation char by volatile matter (tar). Whewellite (CaC{sub 2}O{sub 4}, H{sub 2}O) is the only Ca-bearing mineral found in the cooler area of the coal seam. Decomposition of this mineral, coupled with the presence of SO{sub 2} formed by reaction of organic sulfur with O{sub 2} in combustion, ...
Some aspects of metrological provision of X-ray radiometric analyzers for mineral raw composition and gamma-gamma-logging equipment are considered. Standard samples (SS) based on the phenol-formaldehyde resin with the introduced quantities calculated of element compositions in the form of oxides and salts are described. Principles of metrological provision developed are used when carrying out state acceptance tests of X-ray radiometric analyzer RAL-M-102 ''Ehkran'' and gamma-gamma-logging equipmnt RSK-102. Economic benefit from introduction of an SS set is #approx# 60-100 thousand roubles per year.
Abstract Silicates are one of the most important classes of compounds on this planet, and more than 1000 silicates have been identified in the mineral kingdom. Additionally, several hundreds of artificial silicates have been synthesized. The substitution of oxygen by nitrogen leads to the structurally diverse and manifold class of nitridosilicates. Silicon nitride, one of the most important non-oxidic ceramic materials, is the binary parent compound of nitridosilicates, and it symbolizes the inherent material properties of these refractory compounds. However, prior to the last decades, a broad systematic investigation of nitridosilicates had not been accomplished. In the meantime, these and related compounds have reached a remarkable level of industrial application. This review illustrates...
In this review, the most important inorganic natural gels are presented: opal, aluminosilicate (allophanes) and hydrous iron oxides and silicates. It is demonstrated that natural gels are ordered at the atomic scale. In allophanes, Al is distributed between octahedral and tetrahedral sites. The amount of Al increases as Al/Si ratio decreases. Si-rich allophane have a local structure around Al and Si very different of that is known in kaolinite or halloysite. Transformation of Si-rich allophanes to crystallized minerals implies dissolution-recrystallization processes. On the contrary, in iron silicate with Fe/Si = 0.72, Si and Fe environments are close to those found in nontronite. The gel transformation to Fe-smectite may occur by long range ordering during ageing. In ferric silicate gels, the similarity of local structure around Fe in poorly ordered precursors and what is known in crystallized minerals suggests a solid ...
A mathematical model of a mineral melting cupola furnace for stone wool production has been developed for improving cupola operation. The 1-D, first-engineering-principles model includes mass and heat balances for the gas phase, five solid phases, and four liquid phases. The gas and solid/liquid phases flow countercurrently. Seven chemical reactions account for the conversions of coke, iron oxide, limestone, and gaseous species. The heterogeneous reactions of coke conversion are limited by both kinetics and mass transport. Heat transfer between phases is modeled including both convection and radiation. The model predicts gas concentrations; mass flow rates; and temperature profiles of the solid, melt, and gas in the cupola, as well as heat loss to the water-cooled walls. Inputs to the model include the coke, rock, and blast air properties, the blast air amount, and the coke percentage in the charge. The unknown model parameters are estimated on ...
The objectives of the project were (i) to develop a combination iron oxide production and carbon sequestration plant that will use serpentine ores as the source of iron and the extraction tailings as the storage element for CO2 disposal, (ii) the identification of locations within the US where this process may be implemented and (iii) to create a standardized process to characterize the serpentine deposits in terms of carbon disposal capacity and iron and steel production capacity. The first objective was not accomplished. The research failed to identify a technique to accelerate direct aqueous mineral carbonation, the limiting step in the integration of steel production and carbon sequestration. Objective (ii) was accomplished. It was found that the sequestration potential of the ultramafic resource surfaces in the US and Puerto Rico is approximately 4,647 Gt of CO2 or over 500 years of current US production of CO2. Lastly, a computer model ...
A great deal of studies of the Pu metal dissolution by mineral acids have been made /1-3/. Hydrochloric acid was shown to provide the most complete and fastest dissolution /1-2/. The majority of studies describes the use of HNO_3-HF or HNO_3 with reducing or oxidizing agents present for this purpose /4/. But these methods are not quite adequate because of an extreme corrosiveness of the acids and a high cost of structural materials. That is why a search for more reliable and safer process is still in progress. The HNO_3-HCOOH method of dissolving has been investigated. Some physical-chemical properties of formic acid as well as regulations on its use are presented in /5-8/. (author).
In this, the last of a series of three papers, we discuss a method of forming iron phosphate ceramics by a reduction process. We report the formation of iron oxide ceramics by reducing hematite with iron in a phosphoric acid solution. The reaction results in a rapid-setting ceramic (at room temperature) with a compressive strength of 3700 psi and a density of 1.7 g/cm{sup 3}. Although the exact mineral form of the binder is difficult to determine because it is mostly amorphous and hence is not amenable to X-ray diffraction analyses, this material is expected to consist of iron hydrophosphates. The reduction process is very useful in recycling several industrial wastes that are rich in hematite, including iron mine tailings, red mud (a caustic waste from the alumina industry), and machining swarfs. Formation of ceramics with red mud and swarfs is also discussed.
According to the data of drill cores, outcrops and well logging, two orders base-level cycles are recognized from Zhiluo Formation in Dongsheng area, which consist of 8-14 short-term base-level cycles and 3 mid-term base-level cycles, and their structural types and stacking patterns are discussed by using principles and methods of high-resolution sequence stratigraphic theory. Based on the correlation of mid-term base-level cycles, the control of the A/S (Accommodation/Sediment supply) ratio in mid-term base-level cycles on the scale of sand bodies and physical properties of reservoir is analysed. Studies show that the sand bodies of braided stream in MSC1 of Zhiluo Formation are favourable to uranium mineralization, however, the sand bodies of meandering river in MSC2 and MSC3 are not favourable to uranium mineralization. The change of the A/S results in the difference in characters of sand body, such as physical properties, continuity and so ...
A considerable amount of chemical knowledge of marine sediments has been acquired in recent years but has not yet been utilized by paleomagnetists. On the other hand, geochemists are often unaware of the usefulness of numerous magnetic techniques. In this review we try to bridge this gap, and in particular, we outline many of the chemical and magnetic principles that should allow paleomagnetists to better identify and undertand chemical changes that affect the magnetic properties of marine sediments. The chemical principles include those for distinguishing the four major sources of sediments (continental, biological, authigenic/hydrogenous, volcanic/hydrothermal) from one another by determining elemental abundance distributions, as well as for investigating the stabilities of mineral phases relative to changes in pE and pH. The magnetic principles include the effects of authigenesis and diagenesis on magnetic properties, particularly on the direction and intensity ...
High-resolution sequence stratigraphy has been applied widely in the petroleum exploration and development, many achievements have been achieved. However, it is in the beginning stage that high-resolution sequence stratigraphy is applied to explore the sandstone-type uranium deposits in Erlian Basin. By applying principles of high-resolution sequence stratigraphy and taking typical boreholes as an example, sedimentary cycles of Saihan Formation, the ore-bearing formation in Baiyinwula area are divided and correlated through cross sections. One long-term cycle (LSC_1), two middle-term cycles (MSC_1, MSC_2) have been identified in this study. Based on this and combined with the mineralization character of sandstone uranium deposits in this area, it is presented that the interlayer oxidation zone is developed mainly in the rising hemicycle of MSC_1 and uranium ore bodies predominantly in channel sand bodies that were developed in the system tract ...
Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals that releases highly acidic, sulfate, and metals-rich drainage. In this study, alkaline industrial wastes were mixed with acid mine tailings in order to obtain neutral conditions. A series of column leaching tests were performed to evaluate the behavior of reactive mine tailings amended with alkaline-additions under dynamic conditions. Column tests were conducted of oxidized mine tailings combined with cement kiln dust, red mud bauxite, and mixtures of cement kiln dust with red mud bauxite. The pH results show the addition of 10% of alkaline materials permits the maintenance of near neutral conditions. In the presence of 10% alkaline material, the concentration of toxic metals such as Al, Cu, Fe, Zn are significantly reduced as well as the number of viable cells (Thiobacillus ferrooxidans) compared to control samples.
Research highlights: #-># Red mud residues (RM) were disposed in alumina production. #-># Utilization of Red mud residues was affected by its iron content. #-># Superconducting magnetic separation (HGSMS) was used in iron separation from RM. #-># RM with high and low iron contents were separated in HGSMS. - Abstract: The disposal of bayer red mud tailings now seriously threats the environment safety. Reduction and recycling of red mud is now an urgent work in aluminum industry. High gradient superconducting magnetic separation (HGSMS) system was applied to separate the extreme fine RM particles (<100 #mu#m) into high iron content part and low iron content part. Two sorts of RM were fed in the HGSMS. The iron oxide contents in concentrates were about 65% and 45% when RM 1 and RM 2 were fed respectively. Meanwhile, the residues contained 52.0% or 14.1% iron oxide in residues after eight separation stages when RM 1 and RM 2 were fed ...
Preparation of a uranous nitrate solution from the reduction process of a uranyl nitrate solution by using electrodialysis technique with a cation exchange membrane has been studied. Uranyl ions were reduced into uranous ions in a nitric acid solution stabilized by hydrazine sulfate in a two-compartment electrolytic cell made from flexiglass. Platinum and carbon or stainless steel were used as anode and cathode, respectively. The electrodialysis process was carried out at room temperature. A piece of cation exchange membrane was inserted between the two compartments and the distance between electrode and membrane was 1.5 cm and this was kept constant throughout the experiment. A 100 ml of a nitric acid 1.4 M solution was in the anode chamber as analyte, whilst a 100 ml of a uranyl nitrate solution with the uranium concentration of 23.97 g/l was in the cathode chamber containing hydrazine sulfate. The parameters tasted were reduction voltage, the amount of hydrazine sulfate added, and ...
Bone mineral density is considered to be the standard measure for the diagnosis of osteoporosis and the assessment of fracture risk. The majority of fragility fractures occur in patients with bone mineral...Full Text Available
More than 2,500 Moessbauer spectroscopic studies on minerals have been published since 1960. These papers contain approximately 8,000 sets of Moessbauer mineral data on at least 400 different minerals. This information has been compiled into a database that includes isomer shifts, quadrupole splittings, and magnetic hyperfine interactions at room, liquid nitrogen, and liquid helium temperatures. The database provides a profile of the Moessbauer research performed to date on minerals, including type and locality of minerals investigated, significance of the studies and results, and location of the research facilities. The data and information are available both in printed and magnetic form.With the establishment of this resource, the Moessbauer Effect Data Center has begun a systematic evaluation of the Moessbauer mineral data. It is anticipated that this ...
Bone integrity and mineral status were studied with a noninvasive method in uremic patients with severe secondary hyperparathyroidism undergoing maintenance hemodialysis.
Hydrothermal oxidation (HTO) is a promising technology for the treatment of aqueous-fluid hazardous and mixed waste streams. Waste streams identified as likely candidates for treatment by this technology are primarily aqueous fluids containing hazardous organic compounds, and often containing inorganic compounds including radioisotopes (mixed wastes). These wastes are difficult and expensive to treat by conventional technologies (e.g. incineration) due to their high water content; in addition, incineration can lead to concerns related to stack releases. An especially attractive potential advantage of HTO over conventional treatment methods is the total containment of all reaction products within the overall system. The potential application of hydrothermal oxidation (HTO) technology for the treatment of DOE hazardous or mixed wastes has been uncertain due to concerns about safe and efficient operation of the technology. In principle, aqueous ...
This book presents topics on: Density of rocks and minerals, includes histograms of density ranges; elastic constants of minerals, elastic moduli, thermal properties; inelastic properties, strength and rheology for rocks and minerals, rock mechanics and friction, and stress-strain relations; radioactivity, decay constants and heat production of isotope systems in geology; seismic attenuation, in rocks, minerals, and the earth, with application to oil exploration and terrestrial studies; and index.
The U.S. Geological Survey, in cooperation with the U.S. Department of Energy, is conducting a study to determine the natural geochemistry of the Snake River Plain aquifer system at the Idaho National Engineering Laboratory (INEL), Idaho. As part of this study, a group of geochemical reactions that partially control the natural chemistry of ground water at the INEL were identified. Mineralogy of the aquifer matrix was determined using X-ray diffraction and thin-section analysis and theoretical stabilities of the minerals were used to identify potential solid-phase reactants and products of the reactions. The reactants and products that have an important contribution to the natural geochemistry include labradorite, olivine, pyroxene, smectite, calcite, ferric oxyhydroxide, and several silica phases. To further identify the reactions, analyses of 22 representative water samples from sites tapping the Snake River Plain aquifer system were used to determine the ...
Cinnabar, a naturally occurring mercuric sulfide (HgS), has long been used in combination with traditional Chinese medicine as a sedative for more than 2000 years. Up to date, its pharmacological and toxicological effects are still unclear, especially in clinical low-dose and long-term use. In this study, we attempted to elucidate the effects of cinnabar on the time course of changes in locomotor activities, pentobarbital-induced sleeping time, motor equilibrium performance and neurobiochemical activities in mice during 3- to 11-week administration at a clinical dose of 10 mg/kg/day. The results showed that cinnabar was significantly absorbed by gastrointestinal (G-I) tract and transported to brain tissues. The spontaneous locomotor activities of male mice but not female mice were preferentially suppressed. Moreover, frequencies of jump and stereotype-1 episodes were progressively decreased after 3-week oral administration in male and female mice. Pentobarbital-induced sleeping time ...
One of the main problems facing the mining sector is the production of acid mine drainage (AMD), which is caused by the oxidation of sulphide minerals in the presence of water. AMD can have a detrimental effect on the environment. One solution is to use soil covering over the materials that cause acid to limit the gas flux by diffusion. A capillary barrier effect is generated by using various layers of different types of soil. In the composite system till and clay normally form the basis of the fine material layer. The use of low sulphide tailings to replace the use of fine grained soil was studied to evaluate its effectiveness. Following both in situ and laboratory experiments spread over an eight-year period, the results indicated that an effective method to limit the oxygen flux and generation of AMD is the use of non-acid generating tailings as the moisture retaining layer. The main concepts that form the basis of the study, analysis and ...
The carbothermal reduction of clay minerals in a nitrogen atmosphere is a well established method for producing #beta#'-sialon. There has been some debate within the literature concerning the role that Fe plays in the formation of the #beta#'-sialon phase. However, most workers accept that Fe is able to either catalyze or promote the formation of #beta#'-sialon although some workers have indicated that the function of the Fe is controlled by gas flow rate and there is evidence that Fe also promotes formation of additional phases. The aim of the present study was to characterize the behaviour of Fe within the #beta#'-sialon synthesis. "5"7Fe Moessbauer spectroscopy was employed for the study because this technique is specific to Fe and does not suffer interference from other elements. Moreover, both the coordination and oxidation state and the relative abundances of the various Fe-containing phases are able to be monitored. A previous Moessbauer ...
A novel visible light sensitive photocatalyst, AgSbO3 was prepared by a conventional solid-state reaction method. This oxide belonging to a cubic-pyrochlore structure can absorb visible light with wavelength up to about 480nm. From the band structure calculation, we found that the top of the valence band consists of the hybridized Ag 4d and O 2p orbitals and the bottom of the conduction band mainly consists of the Ag 5s and the Sb 5s orbitals. Photocatalytic activities were evaluated using O2 evolution from an aqueous silver nitrate solution and decomposition of gaseous 2-propanol under visible light irradiation. We found that AgSbO3 shows a higher O2 evolution activity than WO3 and 2-propanol can be mineralized by the AgSbO3 photocatalysis under visible light irradiation.
Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily at a reasonable cost. A primary example of this is copper heap leaching, where there are no binders currently encountered in this acidic environment process. As a result, operators of many facilities see a large loss of process efficiency due to their inability to take ...
Acid Rock Drainage (ARD) is the product formed by the atmospheric oxidation of the relatively common pyrite and pyrrhotite. Waste rock dumps and tailings containing sulfide mineral have been reported at toxic materials producing ARD. Mining in sulphide bearing rock is one of activity which may lead to generation and release of ARD. ARD has had some major detrimental affects on mining areas. The purpose of this study was carried out to develop disposal method for preventing contamination of water and soil environment by waste rocks dump and tailings, which could discharge the acid drainage with high level of metals. Scope of this study was as following: environmental impacts by mine wastes, geochemical characteristics such as metal speciation, acid potential and paste pH of mine wastes, interpretation of occurrence of ARD underneath tailings impoundment, analysis of slope stability of tailings dam etc. The following procedures were used as part ...
Micronutrient deficiencies in flooded rice have been recognized with increasing frequency in recent years. Zinc deficiency is the most widespread disorder, followed by Fe, Mn, and Cu deficiencies. Boron and Mo deficiencies have not been reported in field culture. The peculiar characteristics of a flooded soil are: 1) a layer of standing water; 2) absence of oxygen; 3) a soil profile largely in a reduced chemical state; 4) the presence of large biological carbon dioxide excesses; 5) the presence of high concentrations of soluble Fe"+"+ and Mn"+"+; 6) alteration of soil pH; 7) the presence of toxic substances; 8) increased soluble Na"+, K"+, Ca"+"+, Mg"+"+, NH_4"+, HCO_3"-, H_2PO_4"-, and Si(OH)_4 in the soil solution. Micronutrient availability in flooded soils is affected by: 1) increased solubility of relatively insoluble minerals due to dilution effects; 2) pH changes in relation to solubility and plant availability; 3) changes in ...
Chlorinated organics are frequently found as harmful soil contaminants and persisted for extended periods of time. A novel approach, named pulsed corona discharge plasma (PCDP), was employed for the degradation of pentachlorophenol (PCP) in soil. Experimental results showed that 87% of PCP could be smoothly removed in 60 min. Increasing pulse voltage, enhancing soil pH, lowering humic acid (HA) in soil and reducing granular size of the soil were found to be favorable for PCP degradation efficiency. Oxidation and physical processes simultaneously contributed to PCP removal in soil and ozone was the main factor in PCDP treatment. C-Cl bonds in PCP were cleaved during PCDP treatment by Fourier transform infrared spectroscopy (FTIR) analysis. The mineralization of PCP was confirmed by total organic carbon (TOC) and dechlorination analyses. The main intermediate products such as tetrachlorocatechol, tetrachlorohydroquinone, acetic acid, formic acid, ...
For high-efficiency coal gasification, investigations were given on effect of coal chars with different conversion rates on coal gasification reactivity. In coal gasification, reactivity of char after pyrolysis governs the efficiency. The reference char conversion in CO2 gasification of coal (weight loss) changes linearly in the initial stage of the reaction, but the reactivity declines as the end point is approached. Char surface area is as large as 400 m{sup 2}/g in the initial stage with the conversion at 20%, but it decreases in the final stage. This phenomenon relates closely with changes in pore size and crystalline structure. Change in the Raman value R which shows incompleteness of char graphite structure and amorphous carbon ratio suggests that an active portion with high reactivity is oxidized preferentially, and a portion with low reactivity remains finally. Minerals in coal are known to accelerate the gasification. However, their ...
Three phosphate based ceramics were studied for the immobilization of tri- and tetravalent actinides: britholites Ca{sub 9}Nd{sub 1-x}An{sub x} {sup IV}(PO{sub 4}){sub 5-x}(SiO{sub 4}){sub 1+x}F{sub 2}, monazites/brabantites Ln{sub 1-2x}{sup III}Ca{sub x}An{sub x}{sup IV}PO{sub 4} and Thorium Phosphate Diphosphate (TPD) Th{sub 4-x}An{sub x}{sup IV}(PO{sub 4}){sub 4}P{sub 2}O{sub 7}. For each material, the incorporation of Th, U(IV), or Ce(IV) in the structure was examined. This work was the early beginning of the incorporation of {sup 239}Pu and/or {sup 238}Pu in order to evaluate the effects of {alpha} -decay on these three crystallographic structures. The syntheses were carried out using dry chemistry methods, involving mechanical grinding then heating treatment (1100 deg C {<=} {theta} {<=} 1400 deg C). For britholites, we showed that the incorporation of thorium was complete for weight loading lower than 20 wt.% through the (Nd{sup 3+}, PO{sub ...
The bone mineral content of 109 lumbar vertebrae from 36 different subjects was determined by dual photon absorptiometry. The mean age of the subjects was 58.5 years (range, 31 to 79 years). The ultimate strength of the vertebral bodies was determined during axial compression. Bone mineral content and ultimate compressive strength were correlated (r = 0.86) and the strength was found to increase linearly with increasing amounts of bone mineral content. No differences in this correlation were found in the four vertebral levels (L-4) included in the study, but a difference in this correlation was found between specimens taken from male and female subjects. The results make it possible to estimate the strength of a vertebral body from the knowledge of its bone mineral content as determined by dual photon absorptiometry and provide a basis of estimations of normal and abnormal amounts of bone ...
The authors have evaluated bone mineral content in the vertebral spongiosa by means of Computed Tomography. The method proposed by Genant and Cann [17, 18] has been applied to examine 164 healthy volunteers and 108 patients. Both healthy males and females showed a progressive bone mineral loss increasing with age; the bone mineral loss was most severe in females during the 4th and 5th decade of life. Pathology included patients with osteoporotic fractures (vertebral and femural neck), patients with partial gastrectomy, renal failure, primary hyperparathyroidism, Cushing syndrome, corticosteroid therapy. Bone mineral values were significantly lower in most pathologic groups. Computed Tomography proves thus to be a valuable method to assess bone mineral content and to identify patients at risk for fractures.
{sup 90}Sr, with a long half-life of 28.5 years, is the most dangerous strontium isotope. The adsorption behavior of radionuclides in the environment are closely related to the safe disposal of radioactive wastes. Since various types of minerals may exist in and around the repositories used for ultimate disposal of nuclear waste, the adsorption behavior of certain radionuclides onto and from these minerals and similar adsorbents should be studied in order to estimate the rates of transport of the nuclides in the event of water penetration into and through the repository. Information on the adsorption properties of the purified individual clay minerals may not be sufficient to predict the adsorption properties of a corresponding mixture, because these clay minerals may interact with each other and lead to modification of the adsorption properties of the mixture as compared to the pure ...
We have studied the dissolution behavior of uraninite, becquerelite, schoepite and uranophane. The information obtained under a variety of experimental conditions has been combined with extensive solid phase characterizations, performed in both leached and unleached samples. The overall objective is to construct a thermodynamic and kinetic model for the long-term oxidation alteration of UO{sub 2}(s), as an analogy of the spent nuclear fuel matrix. We have determined the solubility product for becquerelite (logK{sub s0} 32.7{+-}1.3) and uranophane (logK{sub s0} = 7.8{+-}0.8). In some experiments, the reaction progress has shown initial dissolution of uranophane followed by precipitation of a secondary solid phase, characterized as soddyite. The solubility production for this phase has been determined (logK{sub s0} = 3.0{+-}2.9). We have studied the kinetics of dissolution of uraninite, uranophane and schoepite under oxidizing conditions in ...
Nuclear testing at and around the Nevada Test Site (NTS) resulted in widespread contamination from transuranic and other radionuclides, as well as from other toxic inorganic and organic contaminants. The type of contamination, including spatial distribution and type of radionuclides present, depends on the type of testing performed. Remediation of the contaminated areas is currently under way. The optimum in situ or ex situ remediation technology depends on the degree of interaction between the particular radionuclide, or contaminant in general, and the soil matrix, among other factors. The objective of this project was to evaluate the sorption affinity of NTS soils for common non-transuranic radionuclides. The sorption of cobalt (Co) on soils from two different areas of the NTS, namely the Little Feller and Cabriolet event sites, was studied. Experiments were conducted as a function of pH, solid concentration, total Co concentration, ionic strength, and particle size fraction. ...
Four advanced oxidation processes (UV/TiO2, UV/IO4^-, UV/S2O8^2^-, and UV/H2O2) were tested for their ability to mineralize naphthenic acids to inorganic carbon in a model oil sands process water containing high dissolved and suspended solids at pH values ranging from 8 to 12. A medium pressure mercury (Hg) lamp was used, and a Quartz immersion well surrounded the lamp. The treatment goal of 5mg/L naphthenic acids (3.4mg/L total organic carbon (TOC)) was achieved under four conditions: UV/S2O8^2^- (20mM) at pH 8 and 10, and UV/H2O2 (50mM) at pH 8 (all with the Quartz immersion well). Values of electrical energy required to meet the treatment goal were about equal for UV/S2O8^2^- (20mM) and UV/H2O2 (50mM) at pH 8, but three to four times larger for treatment by UV/S2O8^2^- (20mM) at pH 10. ...
Phase II Randomized Study of the Effect of Zoledronate Versus Observation on Bone Mineral Density of the Lumbar Spine in Patients Undergoing Risk-Reducing Excision of Both Ovaries (GOG-0215). See the protocol summary.
Elemental composition and distribution of the mineral reserves in the endosperm and embryo tissues of Ricinus communis cultivars Hale and Zanzibarensis were investigated. Energy dispersive...Full Text Available
OBJECTIVEHormonal contraceptives may adversely affect bone mineral density . However, racial differences and the reversibility of these changes are poorly understood....Full Text Available
Phosphorus is an essential mineral that maintains cellular energy and mineralizes the skeleton. Because complex actions of ion transporters and regulatory hormones regulate serum phosphorus concentrations,...Full Text Available
Transmission electron microscopy analysis (TEMA) was used to analyze the bronchoalveolar lavage fluid (BALF) of 262 subjects occupationally exposed (OE) to nonfibrous mineral particles (NFMP) and 42...Full Text Available
To assess the effects of increasing the mineral content of parenteral nutrition solutions on the biochemical and radiological indicators of metabolic bone disease of prematurity 27 neonates who required...Full Text Available
This study was performed to investigate the association between hair mineral levels and nutrient intakes, age, and BMI in female adults who visited a woman's clinic located in Seoul. Dietary intakes...Full Text Available
The bone mineral areal content and the ultimate compressive strength were determined in 109 lumbar vertebrae from 36 subjects. The bone mineral areal content was related to the number, shape, and localization of the Schmorl's nodes detected in the x-rayed and sectioned vertebral bodies. One type of node, irregular in shape and localization, occurred only in the vertebrae with low bone mineral areal content values and thus in vertebrae with relatively low compressive strength. A second type of Schmorl's nodes, regular in shape and localization, did not reflect any general weakness of the vertebral bodies. PMID:6623194
Papers in this book illustrate the utility of mineral biotechnology with respect to biobeneficiation, bioleaching, bioremediation and biomineralization. Papers of particular interest to the coal industry include: depression of pyrite flotation by yeast and bacteris (S.K. Kawatra and T.C. Eisele); desulfurization of coal by microbial flotation in a semicontinuous system (T. Nagaoka and others); biochemical removal of HAP precursors from coal - INEEL slurry column testing (K.S. Noah and G.J. Olson); microorganisms, biotechnology and acid rock drainage - emphasis on passive-biological control and treatment methods (N. Kuyucak); and utility of bioreagents in mineral processing (P. Somasundaran and others).
Malnutrition?in the form of insufficient energy intakes?affects millions of people worldwide and the negative impact of this kind of hunger is well acknowledged, not least by agronomists trying to increase yields to ensure a sufficient supply of food. This review focuses on another, more particular and ?hidden? form of malnutrition, namely mineral malnutrition. It illustrates the burden of disease that is caused by mineral deficiencies and the social and economic consequences they bring about. Mineral malnutrition has a considerable negative impact on individual well-being, social welfare and economic productivity. Agricultural scientists should keep the nutritional qualities of food in mind and?next to optimizing the agricultural properties of crops that are paramount for their adoption b...
The effect of a mineralizer, magnesium silicate, on the nitridation of compacts consisting of silicon, clay, silica and silicon carbide was examined in terms of their reaction depth, density, porosity, phase composition and microstructure. It was found that addition of mineralizer slowed down the nitridation significantly. The kinetic process of isothermal nitridation in the presence of magnesium silicate obeys a parabolic rate law. Otherwise it obeys a linear rate law. The results suggest that nitrogen transportation is the limiting step during nitridation when mineralizer is added. The mechanism of nitridation is discussed in terms of phase composition and microstructure. Copyright (2000) The Australian Ceramic Society
A chemical equilibrium model is used, implemented in a compact FORTRAN package called HITEQ, to investigate possible mineral deposition related to prereinjection treatment of Cerro Prieto brines for silica removal. Large saturation ratios of the treated brines with respect to several minerals are indicated by these computations. As a remedy, an inexpensive CO/sub 2/ removal scheme aimed at inhibiting carbonate mineral precipitation is proposed. This scheme is quantitatively discussed with the aid of HITEQ. It is concluded that the proposed treatment is both technically and economically feasible.
Thermodynamic analysis of dissolution processes of tungsten minerals in citric acid solutions in the absence and in the presence of hydrochloric acid has been carried out by means of calculation of Gibbs energy of the chemical reactions. Kinetic characteristics, such as specific dissolution rates and activation energies, are determined. It is established that the dissolution reactions studied take place in kinetic region. A possibility of scheelite selective dissolution in the presence of other tungsten minerals is shown.
Liver paste or foie gras, which is a French term meaning fatty liver, was produced traditionally from goose and duck. Chickens are also used in the making of foie gras. The present study deals with the properties and quality of raw chicken and duck liver in comparison with manufactured liver paste (foie gras). Raw chicken liver contained 24.60% protein, 6.00% fat, 1.40 % ash, and 66.80% moisture. The average mineral values were 83.65, 50.75, 5.29, 1.15, 0.154, 0.683, 0.317 and 0.066 {mu}g/g of Fe, Zn, Cu, Mn, Cd, Pb, Ni, and Cr, respectively. The processing of liver paste (Foie gras) changed the composition of raw liver due to a loss in moisture, a release of fat and the addition of butter as a fat source. Chicken liver paste contained 27.8% moisture, 10.1% protein, 58.2% fat, and 0.8% ash. Mineral contents were 68.90, 40.50, 1.60, 1.1, 0.08, 0.22, 0.04 and 0.04 {mu}g/g of Fe, Zn, Cu, Mn, Cd, Pb, Ni, and Cr, respectively. The chemical, ...
Abstract A facile and efficient single-step mineralization approach was exploited for achieving nanoscopic hydroxyapatite (HAP) crystal layer in chitosan porous matrix, wherein a mixed water-ethanol solvent was used to control the growth of minerals. The crystallographic structure, morphology, and mechanical properties of the scaffold were analyzed with XRD, FTIR, environmental scanning electric microscopy (ESEM), TEM, and compression tests. The behaviors and responses of MC3T3-E1 pre-osteoblast cells on the scaffolds were studied as well. The results showed that the scaffolds kept woodpile structure with predefined and controlled hierarchical structure after mineralization. The inorganic phase in the mineralized chitosan scaffolds was determined as pure rod-like HAP, which settled densely...
MINER?A is a high resolution, fully active detector designed to study neutrino interactions on nuclei in the NuMI beam at Fermi National Accelerator Laboratory. The active volume of the detector consists of 3 tons of plastic scintillator and includes embedded targets of 4He, C, H2O, Fe and Pb. The MINER?A collaboration expects to perform precision, A-dependent neutrino cross section measurements in the 1?10 GeV region, measure the axial form factor, and study nuclear shadowing of F2, quark-hadron duality and coherent pion production, among other topics. MINER?A began data taking in the fall of 2009. This paper describes the MINER?A experiment and provides an overview of the physics objectives along with estimated uncertainties of the measurements and the tentative projected schedule of dat...
Examinations of polished and dry cut sections of feed and tuyere coke revealed some possible mechanisms for the physical influence of mineral compounds on the reactivity and strength of coke. It was observed that rounded particles of mineral phases that are exposed to the pore walls and surface of coke at high temperature create an inorganic cover, thus reducing the surface available for gas-solid reactions. The particles of mineral matter that have a low melting point and viscosity can affect the coke at earlier stages in the blast furnace process, acting in the upper parts of the blast furnace (BF). The temperature-driven redistribution of mineral phases within the coke matrix probably leads to the creation of weak spots and in general to anisotropy in its properties, thus reducing its strength. 9 refs., 2 figs., 1 tab.
Health risks associated with inhalation of mineral dusts have been identified to a great extent through epidemiology studies, but also have been assessed by conducting subchronic and chronic inhalation studies typically on rodents. However, in vivo studies are softly, time-consuming, requiring complex technologies, and may not yield information on cellular and molecular mechanisms of response. As a result, the use of in vitro cell culture systems has played an important role in studying the toxicology of mineral dusts and providing insight into action mechanisms. This article reviews selected in vitro approaches that are used to investigate the cytotoxic and inflammatory properties of mineral particles and fibers. In addition key findings as they relate to understanding the toxicology of mineral dusts are presented. 165 refs., 1 fig., 5 tab.
Please cite this paper as: Ectopic mineralization of connective tissue in Abcc6-/- mice: effects of dietary modifications and a phosphate binder - a preliminary study. Experimental Dermatology 2008; 17: 203-207. Abstract: Pseudoxanthoma elasticum (PXE), a heritable multisystem disorder, is caused by mutations in the ABCC6 gene. We have developed a murine model for PXE by targeted inactivation of the corresponding mouse gene. A feature of this mouse model is ectopic mineralization of connective tissue capsule surrounding the bulb of vibrissae. This study was designed to investigate the effect of dietary sevelamer hydrochloride (Renagel), a phosphate binder, and specific mineral modifications on ectopic mineralization of connective tissue in Abcc6-/- mice. Three groups were fed a specific di...
Mineral matter in coals is important in various senses for coal liquefaction. It is possible that the catalytic activity is affected by the interaction between catalyst and mineral matter. Iron-based catalyst forms pyrrhotite in the process of liquefaction, but the interaction between it and mineral matter is not known in detail. In this study, the interaction between mineral matter and catalyst and the selective reaction between them were investigated. Tanito Harum coal was used for this study. This coal contains a slight amount of siderite and jarosite besides pyrite as iron compounds. Liquefaction samples were obtained from the 1 t/d NEDOL process PSU. The solid deposits in the reactor mainly contained pyrrhotite and quartz. A slight amount of kaolinite was observed, and pyrite was little remained. It was found that the catalyst (pyrrhotite) often coexisted with quartz, clay and calcite. 8 figs., 2 ...
A multiple metal oxide sorbent supported on a zeolite of substantially silicon oxide is used for the desulfurization of process gas streams, such as from a coal gasifier, at temperatures in the range of about 1200.degree. to about 1600.degree. F. The sorbent is provided by a mixture of copper oxide and manganese oxide and preferably such a mixture with molybdenum oxide. The manganese oxide and the molybdenum are believed to function as promoters for the reaction of hydrogen sulfide with copper oxide. Also, the manganese oxide inhibits the volatilization of the molybdenum oxide at the higher temperatures.
The thesis relates to an investigation done on greenhouse gases in coniferous forest soils. The production of nitrous oxide (N{sub 2}O) and carbon dioxide (CO{sub 2}), and the consumption of methane (CH{sub 4}) in a temperate forest soil were studied by a rapid and sensitive gas chromatographic (GC) method for analysing all three greenhouse gases at or below ambient levels. Gas fluxes were measured in soil incubation and lysimeter experiments. 15 soil samples were taken at random within a 100 m{sup 2} area in a Norway spruce forest stand (Picea abies). The fluxes of N{sub 2}O, CH{sub 4} and CO{sub 2} were measured under standardized laboratory incubation conditions to investigate spatial variability in relation to other factors such as nitrogen (N) mineralization rate, nitrification rate, organic carbon (OC), total N and pH. The effects of temperature, soil moisture content, and ammonium addition were also studied in an incubation experiment. A ...
Microorganisms associated with fractured basalt core were compared to those suspended in groundwater pumped from the same well in the eastern Snake River Plain Aquifer (Idaho, USA). Two wells influenced to different degrees by a mixed-waste plume in the fractured basalt aquifer were examined. In one well, an array of dialysis cells filled with either deionized water or crushed basalt was equilibrated to compare the microorganisms collected in this fashion with those from core and groundwater samples collected in a traditional manner from the same well. Analyses were performed to characterize these samples and to provide a basis for comparison. These included total cell counts by microscopy; total biomass by phospholipid fatty acid analysis; enumerations of viable aerobic heterotrophs, groups of putative aerobic co-metabolic TCE-degraders and aerobic H2-oxidizing bacteria; mineralization of 14C- labeled acetate; and enrichments for dissimilatory ...
Dissolved humic substances (humic and fulvic acids) occur in surface waters and groundwaters in concentrations ranging from less than 1 mg(C)/L to more than 100 mg(C)/L. Humic substances are strong complexing agents for many trace metals in the environment and are also capable of forming stable soluble complexes or chelates with radionuclides. Concentrations of humic materials as low as 1 mg(C)/L can produce a detectable increase in the mobility of some actinide elements by forming soluble complexes that inhibit sorption of the radionuclides onto rock materials. The stability of trace metal- or radionuclide-organic complexes is commonly measured by an empirically determined conditional stability constant (K'), which is based on the ratio of complexed metal (radionuclide) in solution to the product concentration of uncomplexed metal and humic complexant. Larger values of stability constants indicate greater complex stability. The stability of radionuclide-organic complexes is ...
Irradiation is efficient at extinction fungi contamination in peanuts. Peanuts have high biologic value protein, minerals, vitamin E, complex B, and high concentration of lipids. The objective of this research is to evaluate the gamma irradiation effect on color, total phenolic, antioxidant activity, and fatty acid profile in peanuts (Arachis hypogaea L.). Cultivars IAC-Tatu ST and IAC-Runner 886 were submitted to gamma radiation with doses of 5.0; 7.5; 10.0, and 15.0 kGy and storage at room temperature. There was no significant difference in the color of IAC-Tatu ST. However, significant difference was found in the luminosity and Chroma in IAC-Runner 886. Total fenolics differed from the control with 33.27 mg.g-1 and treatment dose of 10.0 kGy with 58.60 mg.g-1 in IAC-Tatu ST. This parameter not had significant difference in IAC-Runner 886 and the control with 51.59 mg.g-1. The antioxidant activity did not present significant difference with a dose of 10.0 kGy, ...
This is the final report of a three year DOE funded project titled ''A real-time coal content/ore grade (C{sub 2}OG) sensor''. The sensor, which is based on hyperspectral imaging technology, was designed to give a machine vision assay of ore or coal. Sensors were designed and built at Resonon, Inc., and then deployed at the Stillwater Mining Company core room in southcentral Montana for analyzing platinum/palladium ore and at the Montana Tech Spectroscopy Lab for analyzing coal and other materials. The Stillwater sensor imaged 91' of core and analyzed this data for surface sulfides which are considered to be pathfinder minerals for platinum/palladium at this mine. Our results indicate that the sensor could deliver a relative ore grade provided tool markings and iron oxidation were kept to a minimum. Coal, talc, and titanium sponge samples were also imaged and analyzed for content and grade with ...
Methods are discussed for optimization of organizational model of longwall mining. Operations at a working face, their duration, number of miners, miner qualifications are analyzed. The so-called method for allocation of heteregeneous resources is used. Using the method optimum organizational models of working faces are constructed. The models consider working conditions, coal output, personnel, miner qualifications, duration of various operations and of idletime, and safety regulations. A computer code developed by the author for optimizing organizational models of longwall mining is described. 9 refs.
This was a project to investigate the crystal chemistry of OH and H{sub 2}O substitution in silicate minerals by use of X-ray and neutron diffraction methods combined with IR spectroscopy and to interpret and generalize the results using an electrostatic model for these mineral structures. Using these data together with published H position data electrostatic parameters for H sites were calculated from a simple electrostatic model. The data were then used to refine the model for incorporation of H into the wadsleyite structure. This has led to recent work on the synthesis and characterization of hydrous wadsleyites.
Heyuan mineralization belt is a structure-magmatic activities belt which is charcterized by strong plastic deformation and shearing. The squeeze (overthrust) structure is formed early. Later stretch produced slide shovel-shaped normal fault which control the red basin and uranium mineralization. Comprehensive study shows that this area is of favorable uranium metallogenic condition due to the rich uranium source and higher degree of geology work, it is a target for the new round resources exploration. (authors)
A multiphase origin of the Cu-Co ores in the western part of the Lufilian fold-and-thrust belt in Central Africa is proposed based on literature, satellite image interpretations and petrographic and fluid inclusion analyses on samples from the stratiform mineralization of Kamoto and Musonoi (DR Congo). The various mineral occurrences in the Katanga Copperbelt can be classified in distinct categories: stratiform, supergene enrichment and vein-type. The stratiform mineralization form the largest group and can be found mainly in Lower Roan (R-2) rocks, which can be identified as ridges on satellite imagery. Ore deposits outside the R-2 occur along lineaments and result often from supergene enrichment.The main phase of the stratiform mineralization in the Katanga Copperbelt occurred during dia...
PAH biomineralization measurements of yardwaste compost samples indicated heterogeneous distribution of active microorganisms and substantial sequestration of the non-polar substrate in the compost matrix. - The purpose of the study was to evaluate the potential of phenanthrene and fluoranthene biodegradation in yardwaste compost materials. These polynuclear aromatic hydrocarbons were chosen for this work because they are relatively readily biodegradable and ubiquitous in the environment. Compost samples were incubated in biometers with "1"4C-labeled phenanthrene and the evolution of "1"4CO_2 was assessed as a measure of mineralization. The "1"4CO_2 evolution varied widely among replicate biometers, possibly as the result of (1) uneven and patchy colonization of phenanthrene-degrading microorganisms on compost particles, and (2) non-uniform dispersion of the labeled substrate spike into the yardwaste microenvironment. Mineralization of ...
Mineralization and volatilization of ring labelled "1"4C-2,4-dichlorophenoxyacetic acid in soil was studied over a period of six weeks under laboratory conditions at 25 deg. C in three different soils collected from three sites, Delhi, Jaipur and Ludhiana. A very slow rate of both mineralization and volatilization was observed in all the three soils. The observed mineralization, was highest for the Delhi soil, 0.93%, followed by the Ludhiana soil, 0.73% and the Jaipur soil 0.14% in 42 days. The extent of volatilization was 0.46% for the Jaipur soil, 0.37% for the Ludhiana soil and 0.32% for the Delhi soil. (author)
To quantify the opportunities for natural gas and identify technological advances needed to capture such opportunities, the mineral-wool industry was analyzed with respect to the principal companies, their capabilities, and markets. The mineral-wool industry is stable with a slightly declining market. Of its market segments, only commercial acoustic insulation (which is currently dominant) is likely to be affected by growth in the next ten years. The principal process is based on treatment of blast-furnace slags in a cupola furnace using coke as the fuel and reducing agent. Expanded use of gas, as a substitute for coke, would eliminate environmental problems and expand the latitude of suitable raw materials. The study provides insights into the mineral-wool industry and identifies factors that may constitute bases for future usage of natural gas.
Direct radiological measurements of the mineral content of femoral bone were performed in 13 patients on maintenance dialysis. They were found to be sufficiently sensitive to be used for monitoring,...Full Text Available
The fatigue and fracture behavior of hard tissues are topics of considerable interest today. This special group of organic materials comprises the highly mineralized and load-bearing tissues...Full Text Available
The heat capacity and heat of fusion were measured for a number of minerals using differential scanning calorimetry (DSC). The DSC measurements showed that the heat of fusion for the minerals is very low compared to the heat of fusion for pure crystalline phases reported elsewhere. A model for the melting behaviour of mineral materials in terms of melting interval, heat capacities and heat of fusion has been developed. The only model input is the chemical composition of the mineral material. The model was developed to be implemented in a detailed model of a cupola furnace, thus the focus for the development was not only precision but also to obtain a model that was continuous and differentiable. The model is based on several different submodels that each covers a part of the heating and melting of rocks. Each submodel is based on large amounts of empirical data. Comparison of the model and the DSC ...
Physiological bone remodeling is a highly coordinated process responsible for bone resorption and formation and is necessary to repair damaged bone and to maintain mineral homeostasis. In addition to...Full Text Available
... Mineral and Organic Matter in the Coastal and Near-Coastal Ocean. ... Personal Author(s) : Stavn, Robert H. ; Spiering, Bruce A. ; Gould, Richard W ...
Background: Apheresis is a procedure to selectively obtain blood components. For the collection process citrate is routinely used. It inhibits coagulation by binding to ionized calcium and leads to metabolic alkalosis. Objective: Whether regular apheresis affects bone and mineral metabolism is unknown. The intention of this study was to investigate 1) the acute effects of apheresis on acid-base balance, bone and mineral metabolism and 2) to compare bone mineral density (BMD) at the lumbar spine and hip of donors to matched control subjects. Design: In this open, observational, single-center, cross-sectional study we enrolled 102 regular plasma and thrombocyte donors to pursue objective 1) and compared those to 102 matched controls (CTR) for objective 2). Results: Platelet donation led to s...
Thermoluminescence (TL) properties of sphene and epidote are of interest in studies related to their radiation damage. Natural and artificially induced TL of these minerals has, therefore, been investigated. Both minerals exhibit complex glow curves with several overlapping peaks. The Tsub(m) -Tsub(STOP) thermal cleaning procedure has revealed three peaks in the ..gamma.. ray induced glow curve of each mineral. That these peaks obey second order kinetics was indicated by the continuously slanting structure of the Tsub(m)-Tsub(STOP) curve. The TL parameters E and s have been calculated using (i) the initial rise method, and (ii) the glow-peak shape method. In general, the values of E calculated by the first method are found to be higher than those from the second. The TL curve-fitting method is also applied in order to calculate these parameters and to serve as a cross-check on the results.
Following a brief overview of the terrestrial distribution of boron in rocks, soil, and water, the history of the discovery, early utilization, and geologic origin of borate minerals is summarized....Full Text Available
Aerosol particles are ubiquitous in the troposphere and exert an important influence on global climate and the environment. They affect climate through scattering, transmission, and absorption of...Full Text Available
The methods are described of determining natural radionuclides, viz., thorium, uranium, radium, radon, polonium, actinium, and protactinium. The analysis is also described of ores, rocks, minerals, water, air. (M.D.).
A hydrous oxide film for the application as dielectric film is synthesized by immersion of pure aluminum in hot water. From a Rutherford backscattering analysis, the ratio of aluminum to oxygen atoms was found to be 3:2 in the anodized aluminum oxide film, and 2:1 in the hydrous oxide layer. Anodization of the hydrous oxide layer was more effective for the transition of amorphous anodic oxides to the crystalline aluminum oxides.
In this study, bone mineral density (BMD) of normal (CON), ovariectomized (OVX) and partially nephrectomized (NFR) rats was measured by 31P NMR spectroscopy; bone matrix density was...Full Text Available
Clays and zeolites are among the most important of natural dusts by virtue of their occurrence through out the world on the earth`s surface and their important industrial uses. (The 1:1 layer silicates, including the serpentine and kaolin minerals, are not addressed in this chapter.) This chapter provides basic information on a variety of important aspects of each mineral, including crystal structure diagrams of each and references to more detailed discussions. 110 refs., 20 figs.
The paper intends to lay down the fundamentals of normal mineralisation in the perinatal phase as a basis for investigations of disturbed mineralisation. Data are presented on the percentage area of the mineralized osseous tissue, the osteocyte density, and the mineral contents of healthy bones at this age. Comparative morphological examinations of thin bone sections and microradiographs give a picture of bone development at this age. (orig./AJ).
Distribution of scattered elements in basic minerals of salt-rocks is studied. It is shown that rubidium and cesium are accumulated mainly in carnallites and are contained in small quantities halites. These elements are accumulated primarily in the carnallite production products, wherein their content in a number of cases exceeds by dozens and hundred times their content in source rocks. It is noted that only carnallites may be considered in the list of actual sources for rubidium and cesium separation
Daily exposures of adult beagle dogs to inhaled radon daughters and to uranium ore dust for 4-1/2 to 6 yr have produced respiratory tract carcinomas, at similar cumulative working level months (WLM) of exposures to those which induced carcinomas in uranium miners. Biological data from the beagle-dog experiments can therefore be used for prediction of carcinogenic risk under changing exposure conditions in future uranium miners.
ObjectivesTo extend a set of work carried out previously at Royal Holloway, the Natural History Museum and elsewhere, and instigated, to a considerable extent, by the PI to determine~%~~%~1. whether there is any significant difference in the performance of clay minerals in the presence of leachates generated by wastes from different cultures and/or deposited in different climates;~%~~%~2. what causes some, if not all, clay minerals to aggregate after reaction with landfill Ieachate;~%~~%~3. the permeabili [continued...]DescriptionAround 1995 it was shown that that interactions between clay minerals and landfill leachate destroy the clay mineral lattice, leading to reduced liner permeability. Recent work indicates that the effect may be caused by dissolution of silica and deposition of amorphous alumina. Most work to date has been done using synthetic ...
A simple sample decomposition and laser fluorimetric determination of uranium at trace level is reported in certain refractory minerals, like ilmenite, rutile, zircon and monazite; environmental samples viz. soil and sediments; industrial waste materials, such as, coal fly ash and red mud. Ilmenite sample is decomposed by heating with ammonium fluoride. Rutile, zircon and monazite minerals are decomposed by fusion using a mixture of potassium bifluoride and sodium fluoride. Environmental and industrial waste materials are brought into solution by treating with a mixture of hydrofluoric and nitric acids. The laser induced fluorimetric determination of uranium is carried out directly in rutile, zircon and in monazite minerals and after separation in other samples. The determination limit was 1 #mu#g x g"-"1 for ilmenite, soil, sediment, coal fly ash and red mud samples, and it is 5 #mu#g x g"-"1 for rutile, zircon and ...
The oxidative stress theory of aging predicts that manipulations that alter oxidative stress/damage will alter aging. The gold standard for determining whether aging is altered is lifespan,...Full Text Available
Bi-U mixed oxides were synthesized by two methods and characterized by X-ray diffraction and X-ray photoelectron spectroscopy. The samples were tested for the catalytic oxidation of carbon monoxide by oxygen. A stepwise redox mechanism consistent with the kinetic results is proposed. (orig.).
This paper presents the characteristics of selected parameters of organic matter of the Tertiary coal samples and organic matter of Carboniferous rock samples from the Spitsbergen. The coal samples were taken from Central Coal Basin (the Longyearbyen region) and from the Forlandsundet Basin (Oscar II Land, the Kaffioyra region). Samples of dispersed organic matter were collected from Suffolk Pynten and Sergeijevfjellet area in Sorkapp Land. The optical properties of coal samples are different from properties of dispersed organic matter. Macerals of vitrinite group dominate in all of the samples. The average content of vitrinite group macerals is much lower in dipersed organic matter samples than it is in coals. The average content of liptinite group macerals is a little lower, and inertinite group macerals is much higher. The average content of mineral matter is higher in organic matter samples than in coal samples. The average value of vitrinite reflectance and ...
Chemical oxidation is a treatment technology that uses powertul chemical oxidizers to destroy organic contaminants. Typical oxidizers used in chemical oxidation processes include ozone, hydrogen peroxide, chlorine, and potassium permanganate. The chemical reaction products are usually simple organic compounds, such as carboxylic acids, and/or inorganic compounds, such as carbon dioxide, water, and simple inorganic complexes (e.g., chloride salts, in the case of chemical oxidation treatment of chlorinated solvents).
In the framework of the search for a ceramic material usable in the radioactive waste storage, uranium and thorium phosphates have been investigated. Their experimental synthesis conditions have been entirely reviewed, they lead to the preparation of four new compounds: U(UO{sub 2})(PO{sub 4}){sub 2}, U{sub 2}O(PO{sub 4}){sub 2}, UCIPO{sub 4}, 4H{sub 2}O, and Th{sub 4}(PO{sub 4}){sub 4}P{sub 2}O{sub 7}. Experimental evidenced are advanced for non existent compounds such as: U{sub 3}(PO{sub 4}){sub 4}, U{sub 2}O{sub 3}P{sub 2}O{sub 7} and Th{sub 3} (PO{sub 4}){sub 4}. Characterization by several techniques (X-rays and neutron powder diffractions, UV-Visible and Infra-red spectroscopies, XPS,...) were performed. The ab initio structure determination of U(UO{sub 2})(PO{sub 4}){sub 2} has been achieved by X-rays and refined by neutron diffractions. Through its physico-chemical analysis, we found that this compound was a new mixed valence uranium phosphate in which U{sup 4+} and UO{sub ...
A geological study was conducted to better understand the nature of cleat development and degree of mineralization in coal seams of the Scollard and Coalspur Formations in western Alberta. The results can be applied to equivalent formations. The source and reservoir rocks of a coalbed methane (CBM) system were described. Coal seams are basically fractured reservoirs with 7 types of cleats. The field work involved cleat minerals sampling and determining cleat attributes such as type, strike and spacing from open-cut mines and outcrops. The laboratory work involved X-Ray diffraction, scanning electron microscopy, energy dispersive microscopy, stable isotope analysis, and fluid inclusions analysis. The study showed that coal seams of the Scollard and Coalspur Formations are widespread and cleated to various degrees. The face and butt cleats strike northeast-southwest and northwest southeast respectively along the structural grain of the Laramide ...
The effect of hydrogen sulfide (H2S) on the chemical looping combustion of coal-derived synthesis gas with bentonite-supported metal oxidesssuch as iron oxide, nickel oxide, manganese oxide, and copper oxideswas investigated by thermogravimetric analysis, mass spectrometry, and X-ray photoelectron spectroscopy (XPS). During the reaction with synthesis gas containing H2S, metal-oxide oxygen carriers were first reduced by carbon monoxide and hydrogen, and then interacted with H2S to form metal sulfide, which resulted in a weight gain during the reduction/sulfidation step. The reduced/sulfurized compounds could be regenerated to form sulfur dioxide and oxides during the oxidation reaction with air. The reduction/oxidation capacities of iron oxide and nickel oxide were not affected by the presence ...
Abstract Incomplete dispersion of aggregates is a well known difficulty when analyzing soil texture of Andosols, particularly if no fresh soil material is available. To facilitate such investigations, several dispersion procedures were carried out on air dried samples rich in short range order minerals, originating from selected Andosol profiles (S Mexico). As a result, we propose an improved method based on a sequential chemical treatment with K oxalate, NH4 oxalate, and oxalic acid that reliably removes cementing agents and allows for a stable dispersion of soil particles after addition of Na pyrophosphate. This method was proved to be well reproducible and highly reliable for routine grain size determinations. The potential error caused by the inherent risk of dissolving primary mineral...
SUMMARY Spontaneous potentials associated with volcanic activity are often interpreted by means of the electrokinetic potential, which is usually positive in the flow direction (i.e. Zeta potential of the rock is negative). The water-rock interactions in hydrothermal zones alter the primary minerals leading to the formation of secondary minerals. This work addresses the study of calcite precipitation in a sand composed of 98 per cent quartz and 2 per cent calcite using streaming potential measurements. The precipitation of calcite as a secondary mineral phase, inferred by high calcite saturation indices and by a fall in permeability, has a significant effect on the electrokinetic behaviour, leading to a significant reduction in the Zeta potential (in absolute value) and even a change in si...
Bone mineral content as determined by computerized tomography (CT) and mechanical strength on axial loading were compared in 36 cadaveric femur specimens. Based on the CT measurements of density and area, the mass of a transverse slice of the femur was estimated. Highly significant correlations were demonstrated between strength and cancellous bone density. Even higher correlations were revealed when the bone masses of the proximal and distal femoral areas were calculated. Based on these findings, an equal distribution of the effective mass of the femur was postulated. This hypothesis was confirmed in an experimental rotational model. The CT attenuation values were also correlated to direct measurements of bone mineral content, i.e. calcium. Moreover, the strength of different metal implants, commonly used in femoral neck fractures, were assessed in cadaver specimens. 134 refs., 13 figs., 12 tabs.
The feasibility of this procedure was investigated using minerals and ore specimens. The substances were ground then fused using LiBO/sub 2/, quenched with 3% HNO/sub 3/ or mixtures of the acid with 2.5% tartaric acid or 30% H/sub 2/O/sub 2/. The quenched melt was usually completely dissolved within 20 min by placing the beakers in an ultrasonic bath. If any residue was detected, appropriate changes were made in the procedure. Once the procedure has been optimized, any remaining black particles were filtered. If these particles disappeared upon subsequent ignition, they were presumed to have been graphite. Most of the refractory minerals investigated should be expected to be converted to soluble form by this process. 1 table.
We compared an idealised mathematical model of the lower part of the pelagic food web to experimental data from a mesocosm experiment in which the supplies of mineral nutrients (nitrogen and phosphorous), bioavailable dissolved organic carbon (BDOC, as glucose), and silicate were manipulated. The central hypothesis of the experiment was that bacterial consumption of BDOC depends on whether the growth rate of heterotrophic bacteria is limited by organic-C or by mineral nutrients. In previous work, this hypothesis was examined qualitatively using a conceptual food web model. Here we explore the extent to which a ?simplest possible?? mathematical version of this conceptual model can reproduce the observed dynamics. The model combines algal?bacterial competition for mineral nutrients (phosphor...
Oxidation of propylene with oxygen, air and a mixture of nitrogen?oxygen in a barrier discharge is investigated. The selectivity towards formation of propylene oxide in pure oxygen is shown to be as high as 45 wt% and the propylene conversion ratio is found to be 12.9 wt%. In the oxidation with air, the propylene oxide selectivity is 23 wt%, while the conversion is 7.5 wt%. The values of propylene conversion and selectivity towards formation of propylene oxide in a barrier discharge are consistent with those obtained by the thermocatalytic methods for production of propylene oxide.
Stable isotopes are valuable tools for research on mineral bioavailability and metabolism. They can be used as tracers with no exposure to radiation and they do not decay over time. Attempts to use stable isotopes of minerals as metabolic tracers were first described only 25 years ago. There were relatively few reports of their use over the next 15 years, but interest in stable isotopes has expanded markedly in the last 10 years. The advantages of stable isotope tracers are so great that scientists have been willing to accept the laborious and costly nature of mineral isotope analysis, and substantial progress has been made in the field. New applications for stable isotopes and new analytical methods have been introduced recently. However, limitations to the approach and methodological problems remain to be resolved. This review describes early work in the field and discusses the advantages and disadvantages of stable ...
Disposable nappies (diapers) have been satisfactorily demineralized and used for the collection of excreta from infants and young children during mineral and trace metal balances. It was possible to...Full Text Available
PurposeDutasteride and finasteride are 5α-reductase inhibitors that dramatically decrease serum levels of dihydrotestosterone. Because androgens...Full Text Available
The melting unit, consisting of a water-cooled cupola furnace, afterburner, heat exchanger, air preheater, consumes most of the supplied energy in the rockwool process. The report maps the energy flows and defines factors of merit according to thermodynam...
Microstructure of the teeth of the sea urchin Lytechinus variegatus was investigated using optical microscopy, SEM (scanning electron microscopy) and SIMS (secondary ion mass...Full Text Available
Though central to our understanding of how roots perform their vital function of scavenging water and solutes from the soil, no direct genetic evidence currently exists to support the foundational model...Full Text Available
The Earth`s troposphere and hydrosphere contain abundant naturally generated dust. The ultimate source materials from which the terrestrially produced dust is generated are the various rock types exposed at the Earth`s surface. Natural dust is a composite of (1) lithic, primary mineral grains; (2) mineral grains formed by secondary chemical reactions; (3) volcanic ash and dust; (4) salts from sea sprays; (5) extra-terrestrial dust; and (6) biologic materials. In this paper the various pathways to the natural generation of dust (via the hydrologic cycle) will be discussed, and two geologically well-known natural dust sources will be described, paying particular attention to quantitative measurements of the dusts from these areas. General dust studies that provide data on possibly global background levels will be presented as well.. A few general aspects of the mineralogical characterization of dust particles and a discussion of some of the ...
The adsorption capacity of radionuclides onto suspended sediment was experimented on each of the coastal seawater sampled around the Kori and the Wolsung nuclear power plant. During the experiment the quantity and size fraction of suspended sediment were adjusted and the seawater and sediment chemistry is approximated to the expected field condition. Because the sorption capacity depends on the specific minerals, ocean chemistry and radionuclide involved, it is necessary to analyze sediment mineralogy. Clay mineral is dominant in seabed mineral and suspended sediment as the result of x-ray diffraction. Radionuclide sorbed to silty-clay mineral can be rather transported to ocean than scavenged to seabed because of low quantity and fine grained suspended sediment in the coast around the Kori and the Wolsung. The result of adsorption examinations shows that {sup 139}Ce and {sup 51}Cr and {sup 110m}Ag are ...
The adsorption capacity of radionuclides onto suspended sediment was experimented on each of the coastal seawater sampled around the Kori and the Wolsung nuclear power plant. During the experiment the quantity and size fraction of suspended sediment were adjusted and the seawater and sediment chemistry is approximated to the expected field condition. Because the sorption capacity depends on the specific minerals, ocean chemistry and radionuclide involved, it is necessary to analyze sediment mineralogy. Clay mineral is dominant in seabed mineral and suspended sediment as the result of x-ray diffraction. Radionuclide sorbed to silty-clay mineral can be rather transported to ocean than scavenged to seabed because of low quantity and fine grained suspended sediment in the coast around the Kori and the Wolsung. The result of adsorption examinations shows that "1"3"9Ce and "5"1Cr and "1"1"0"mAg are strongly ...
The parathyroid hormone receptor (PTHR) is a class B G protein-coupled receptor that plays critical roles in bone and mineral ion metabolism. Ligand binding to the PTHR involves interactions to both...Full Text Available
Hypothyroidism and thyrotoxicosis are each associated with an increased risk of fracture. Although thyroxine (T4) is the predominant circulating thyroid hormone, target cell responses are determined...Full Text Available
DescriptionThe UK horticulture and agriculture industries rely on large inputs of mineral nitrogen (N), phosphorus (P) and potassium (K) fertilisers to maintain product yield and quality. Recovery of applied fertilisers by field crops is inefficient (routinely
Women experience a decline in estrogen and androgen levels after natural or surgically induced menopause, effects that are associated with a loss of sexual desire and bone mineral density. Studies in...Full Text Available
Two gram-negative, motile bacteria isolated from deep subsurface sediments mineralized the nitrogen-containing polyaromatic hydrocarbon quinoline under aerobic conditions and transformed quinoline to...Full Text Available
Laboratory studies investigated the influence of dissolved oxygen tension (DOT) on microbial degradation of hexadecane in cultures with sediment-seawater suspensions. With a fermentor system, it was...Full Text Available
Hydrogen cyanide is a key molecule for chemical evolution studies because, when it is exposed to different sources of energy, it forms various compounds of biological importance. To understand the role of minerals in chemical evolution, a series of experiments was performed. First, the adsorption capacity of HCN on different surface minerals was studied; the results show that HCN is readily adsorbed onto the solids proposed (zeolite, serpentine, dolomite, and sodium montmorillonite), in particular zeolite and montmorillonite. Second, the radiolysis of HCN adsorbed on olivine (as an example of a mineral surface) was also followed; it was found that the rate of HCN decomposition by gamma irradiation is enhanced in the presence of the solid. The third series of studies show that organic material was produced in high abundance from HCN at high radiation doses. The radiolytic products included gases (CO_2, NH_4, and CO) and ...
The electrokinetic patterns of four bacterial species (Bacillus subtilis, Bacillus megaterium, Pseudomonas aeruginosa, and Agrobacterium radiobacter), two yeasts (Saccharomyces cerevisiae and Candida...Full Text Available
In the course of the research project 'Investigations of trace element concentrations in coal seams with different mineral groups', 31 seam coals of the Ruhr Carboniferous were analysed in order to determine the bending of 14 coal-relevant trace elements to the mineral groups and/or minerals of the coals. Products with different ash content were produced by fluctuation of the seam coals in a laboratory cell. The raw coals and fluctuation component products were analyzed chemically and mineralogically in order to get a quantitative raw material characterisation of the sampled material. Particular interest is taken in the chemical and non-ecological composition of the mineral as ash carrier in the coal and the fluctuation component products, as well as in trace element control. (orig./EF).
Objectives To assess the effectiveness of calcium supplementation for improving bone mineral density in healthy children and to determine if any effect is modified by other factors and...Full Text Available
Ammonium sulfate is produced from spent sulfuric acid from the production of alcohols. Certain mineral and organic impurities exist in the sulfuric acid that impair the quality of the ammonium sulfate. A detailed method for the chemical analysis for the impurities is presented.
To carry out studies on the radon behavior under controlled and stable conditions it was designed and constructed a system that consists of two parts: a container of mineral rich in Uranium and an experimentation chamber with radon united one to the other one by a step valve. The container of uranium mineral approximately contains 800 gr of uranium with a law of 0.28%; the radon gas emanated by the mineral is contained tightly by the container. When the valve opens up the radon gas it spreads to the radon experimental chamber; this contains 3 accesses that allow to install different types of detectors. The versatility of the system is exemplified with two experiments: 1. With the radon experimental chamber and an associated spectroscopic system, the radon and two of its decay products are identified. 2. The design of the system allows to couple the mineral container to other experimental geometries to ...
A review of the literature on chronic inhalation studies in which rats were exposed to mineral fibres at known fibre number concentrations was undertaken to examine the specific roles of fibre length...Full Text Available
Mineral scale formation in water distribution piping impedes flow, resulting in pressure and volume reduction and increasing operational costs. Chemical cleaning is both costly and time consuming, and there are health concerns when chemically cleaning pot...
A pure culture of an Agrobacterium sp. (deposited as ATCC 55002) that mineralizes the ferric chelate of EDTA (ferric-EDTA) was isolated by selective enrichment from a treatment facility...Full Text Available
The hierarchical arrangement of collagen and mineral into bone tissue presumabley maximizes fracture resistance with respect to the predominant strain mode in bone. Thus, the ability of cortical...Full Text Available
Phosphoro-uraniferous deposit of Itataia is situated in Precambrian metamorphic terrains, into the litho-stratigraphic unit named Caico Complex. Regionally, the rocks are linearly folded, as a result of compressive tectonic that fits in the regmatic pattern. Rio Groairas' and Itatira's wrench faults form shearing couples in which the drag folds' climax are thrusting faults with axial plane dipping north. Uranium mineralization occurs into a phosphatic rock containing about 80% of collophane - 'collophanite - in association chiefly with marbles or feldsphatic rocks and gneisses. The ore (collophanite) occurs mainly as a stockwork, and it may be massive, (into big joints) or disseminated (impregnating the host rocks). Dark ore appears only in brecciated zones; it is richer in uranium content, but poorer in phosphorous. The highest grade ore is in a very fractured zone, associated to marbles. Supergene enrichment took place in this area. Underground works show that ...
As part of its program to provide technology for reducing undesirable environmental impacts of mineral processing operations, the Bureau of Mines developed the citrate process for desulfurizing industrial stack gases that contain from 0.1 to 2 vol pct SO2...
At the St. Joe Minerals Corp.'s zinc smelter powerplant, an SO2 emission control program evolved into a cooperative program with the Bureau of Mines for installation and initial operation of a citrate process flue gas desulfurization demonstration plant. ...
The measurement of bone loss in patients undergoing maintenance dialysis over a period of two and a half years is reported. The tendency to lose bone is a likely event in renal failure, but depends...Full Text Available
Results of feasibility experiments for determining the mineral content of individual stains on special Sensitized Paper are presented. The stains were formed on the paper by the impaction of laboratory generated salt water droplets. Of the techniques exam...
Failure of bone under monotonic and cyclic loading is related to the bone mineral density, the quality of the bone matrix and the evolution of microcracks. The theory of linear elastic fracture...Full Text Available
The reserves and the mine are described. Planned capacity is 27.5 million tonnes per year of coal for the Sasol II and Sasol III liquefaction plants. There will be 7 longwall faces, 15 entry workings with shotfiring, and 19 entries with continuous miners.
BackgroundHip resurfacing arthroplasty (HRA) is considered a bone-preserving procedure and may eliminate proximal femoral stress shielding and osteolysis. However, in addition to...Full Text Available
Low bone mineral density (BMD) is prevalent in human immunodeficiency virus (HIV)–infected subjects. Initiation of antiretroviral therapy is associated with a 2%–6% decrease...Full Text Available
...2010-10-01 false Who must post a geothermal bond? 3214.10 Section 3214...MINERALS MANAGEMENT (3000) GEOTHERMAL RESOURCE LEASING Personal and... § 3214.10 Who must post a geothermal bond? (a) The lessee...
Abstract Ionizing radiation is a ubiquitous feature of the Cosmos, from exogenous cosmic rays (CR) to the intrinsic mineral radioactivity of a habitable world, and its influences on the emergence and persistence of life are wide-ranging and profound. Much attention has already been focused on the deleterious effects of ionizing radiation on organisms and the complex molecules of life, but ionizing radiation also performs many crucial functions in the generation of habitable planetary environments and the origins of life. This review surveys the role of CR and mineral radioactivity in star formation, generation of biogenic elements, and the synthesis of organic molecules and driving of prebiotic chemistry. Another major theme is the multiple layers of shielding of planetary surfaces from th...
Cesium-137 has contaminated a large area of the wetlands on the Savannah River Site. Remediation of the contaminated wetlands is problematic because current techniques destroy the sensitive ecosystem and generate a higher dose to workers. To address this problem, we proposed a non-trusive, in situ technology to sequester 137Cs in sediments. One intention of this study was to provide information regarding a go/no go decision for future work. Since the proof-of-concept was successful and several minerals were identified as potential candidates for this technology, a go decision was made.
Taconite tailings and their component asbestiform minerals in Lake Superior water had no demonstrable effect on the chronic toxicity of cadmium to the flagfish, Jordanella floridae. Maximum acceptable toxicant concentrations determined in life cycle tests, where effects on survival, growth, reproduction, and bioconcentration were used as endpoints, were between 3.3 to 7.4, 3.0 to 6.5, and 3.4 to 7.3 micrograms cadmium/liter at 0.004, 0.08, and 0.95 mg/liter taconite tailings concentrations, respectively.
Bone integrity and mineral status were studied with a noninvasive method in uremic patients with severe secondary hyperparathyroidism undergoing maintenance hemodialysis. [Italian] Gli autori propongono un metodo non invasivo per studiare la densita' minerale e le caratteristiche geometriche e biomeccaniche dell'osso nei pazienti uremici affetti da iperparatiroidismo secondario grave.
The activity concentrations of potassium, uranium and thorium in minerals and soil samples from a mining site in Ibadan, Southwestern Nigeria were measured using gamma ray spectroscopy method. Effective dose per annum has been calculated from the activity concentrations of dominant gamma-emitting natural radionuclides, potassium, uranium and thorium. Samples collected include minerals (beryl, quartz and feldspar), soil samples from the mining pits, heaps and undisturbed land around the mining site. The activity concentrations of "4"0K, "2"3"8U and "2"3"2Th, respectively in Bq kg-1 in the mineral samples were as follows: 1985 #+-# 16, 4.8 #+-# 0.9 and 11.8 #+-# 5.8 for beryl sample, 115.1 #+-# 27.9, 5.0 #+-# 1.3 and 6.3 #+-# 5.0 for feldspar samples and 1421 #+-# 122, <4.8 and 20.1 #+-# 3.5 for quartz samples. For the soil samples, the mean activity concentrations of "4"0K, "2"3"8U and "2"3"2Th, respectively, were 314.2 ...
An investigation of the mechanism of the oxidation and ammoxidation of propylene was made. The products of the above reactions were acrylonitrile and acrolein for ammoxidation and oxidation, respectively. Also, the ammoxidation and oxidation of allyl alcohol, allyl amine, and their allylic deuterium substituted analogues was studied. It was concluded that oxidation and ammoxidation of propylene have the same rate determining step. Other conclusions about the reaction intermediates were also made.
The electrochemical oxidation as a method to destroy drug residues like Aspirin {sup trademark}, tetracycline or gentamicin in water was investigated with C-Anode (modified by manganese oxides) and Pt Anode. The mechanism of Aspirin {sup trademark} and tetracycline oxidation and the influence of the biocide effect was observed using GC-MS and three different microbiological tests. In general the biological availability increases with progressive oxidation of the antibiotics. (orig.)
The widely accepted oxidative stress theory of aging postulates that aging results from accumulation of oxidative damage. Surprisingly, data from the longest-living rodent known, naked mole-rats [MRs;...Full Text Available
Background. The Free Radical Theory of Aging mechanistically links oxidative stress to aging. Okinawa has among the world's longest-lived populations but oxidative stress in this...Full Text Available
Oxidative stress occurs when the level of prooxidants exceeds the level of antioxidants in cells resulting in oxidation of cellular components and consequent loss of cellular function. Oxidative...Full Text Available
1. Nitric oxide generation is important in the regulation of resistance vessel tone. Until now, however, there has been no evidence of such a role for basal generation of nitric oxide in the skin microcirculation...Full Text Available
The catalytic effects of copper-aluminium-magnesium oxides in the oxidative coupling of phenylethyne is described. The importance of surface properties as a redox site are discussed.
Studies were conducted to quantitate the evolution of nitrogen oxides (NO(x)) from soybean [Glycine max (L.) Merr.] leaves during in vivo nitrate reductase...Full Text Available
Potato tuber mitochondria oxidizing malate respond to NAD+ addition with increased oxidation rates, whereas mung bean hypocotyl mitochondria do not. This is traced to a low endogenous content...Full Text Available
The potential for oxidation of ammonia in anoxic marine sediments exists through anaerobic oxidation by Nitrosomonas-like organisms, utilizing nitrogen dioxide, coupling of nitrification,...Full Text Available
Apparatus and method for selective measurement of tritium oxide in an environment which may include other radioactive components and gamma radiation, the measurement including the selective separation of tritium oxide from a sample gas through a membrane into a counting gas, the generation of electrical pulses individually representative by rise times of tritium oxide and other radioactivity in the counting gas, separation of the pulses by rise times, and counting of those pulses representative of tritium oxide. The invention further includes the separate measurement of any tritium in the sample gas by oxidizing the tritium to tritium oxide and carrying out a second separation and analysis procedure as described above.
The theoretical principles underlying the formation of oxide and, in particular, anodic oxide coatings on metals produced by chemical oxidation, anodizing in solutions, and anodizing in cold plasmas are reviewed. The mechanisms and conditions of anodic oxidation are described, and the structure of anodic oxide coatings on aluminum, magnesium, beryllium, zinc, cadmium, iron, cobalt, nickel, titanium, zirconium, tantalum, and chromium alloys is examined. Attention is also given to various applictins of anodized coatings. 54 references.
The potential use of uranium in the field of catalysis is presented in the first part of this paper. Numerous applications of uranium binary oxides, as well as mixed oxides, are reviewed with a special emphasis on the role of U-Sb-O catalysts in selective oxidation (and ammoxidation) processes. Attempts are made to correlate the electronic structure of uranium, and especially the role that 5f electrons play in bonding, with its promising catalytic properties. In the second part, new data are given for uranium-bismuth mixed oxides in the catalytic oxidation of CO by O_2. Kinetic tests performed in a flow microreactor allow a mechanism to be proposed that involves the direct participation of lattice oxygen of the catalyst in the chemical process (redox mechanism). The high activity can be related to the ability of uranium to change reversibly its oxidation state. ...
The growth of an oxide interfacial layer was recently found to increase the open-circuit voltage (OCV) and efficiency by up to 60 per cent in GaAs metal-semiconductor solar cells. Details of oxidation techniques to provide the necessary oxide thickness and chemical structure and using ozone, water-vapor-saturated oxygen, or oxygen gas discharges are described, as well as apparent crystallographic orientation effects. Preliminary results of the oxide chemistry obtained from X-ray, photoelectron spectroscopy are given. Ratios of arsenic oxide to gallium oxide of unity or less seem to be preferable. Samples with the highest OVC predominantly have As(+3) in the arsenic oxide rather than As(+5). A major difficulty at this time is a reduction in OCV by 100-200 mV when the antireflection coating is vacuum deposited.
The potential use of uranium in the field of catalysis is presented in the first part of this paper. Numerous applications of uranium binary oxides, as well as mixed oxides, are reviewed with a special emphasis on the role of U-Sb-O catalysts in selective oxidation (and ammoxidation) processes. Attempts are made to correlate the electronic structure of uranium, and especially the role that 5f electrons play in bonding, with its promising catalytic properties. In the second part, new data are given for uranium-bismuth mixed oxides in the catalytic oxidation of CO by O/sub 2/. Kinetic tests performed in a flow microreactor allow a mechanism to be proposed that involves the direct participation of lattice oxygen of the catalyst in the chemical process (redox mechanism). The high activity can be related to the ability of uranium to change reversibly its oxidation ...
PurposeCataracts are often considered to be an unavoidable consequence of aging. Oxidative damage is a major cause or consequence of cortical and nuclear cataracts, the most common...Full Text Available
Ethane oxidation was studied in ethane-grown resting cells (mycelia) of an Acremonium sp. and in cell-free preparations of such mycelia. From resting cell experiments evidence was found for a pathway...Full Text Available
Metastable yttrium-oxide films are synthesized using reactive sputter deposition. The yttrium concentration of the as-deposited film is found to vary as a function of the sputter deposition rate. In addition to the synthesis of the cubic equilibrium phase...
Alkali metal doped double perovskites containing manganese and at least one of cobalt, iron and nickel are useful in the oxidative coupling of alkane to higher hydrocarbons.
This patent describes a catalyst composition. It consists of the catalytic oxides of iron, bismuth, molybdenum and magnesium as essential components and optionally the oxides of cobalt, nickel, phosphorus and arsenic.
Background:To determine nutrient requirements by the carbon oxidation techniques, it is necessary to know the fraction of carbon dioxide produced during the oxidative...Full Text Available
May 31, 2011 ... A Theoretical Solid Oxide Fuel Cell Model for System Controls and Stability Design AUTHOR(S): Kopasakis, George; Brinson, Thomas; Credle, ...
Red mud is a waste product of the aluminium refining industry. It is composed of aluminium hydroxide and iron oxide. This study examined the feasibility of using red mud as a catalyst to eliminate volatile organic compounds in atmospheric pollutants. Volatile organic compounds can be eliminated by thermal oxidation between 600 and 1100 degrees C. However, the oxidation of volatile organic compounds can also be accomplished at lower temperatures (200 to 450 degrees C) if a catalyst is present. Currently, the low temperature destruction of volatile organic compounds is not widespread because of the difficulty in deactivating the catalyst. In this study, red mud was calcined in air at 500 degrees C. Under such conditions, the red mud converts to aluminium oxide and iron oxide. These 2 oxides are active and are carbon dioxide selective in the ...
Exploration for epithermal Au has been active lately in the Aegean Sea of the eastern Mediterranean Basin, both in the islands of the Quaternary arc and in those of the back-arc region. The purpose of this study was the structural mapping and analysis for a preliminary investigation of possible epithermal gold mineralization, using remotely sensed data and techniques, structural and field data, and geochemical information, for a specific area on the Island of Lesvos. Therefore, Landsat-TM and SPOT-Pan satellite images and the Digital Elevation Model (DEM) of the study area were processed digitally using spatial filtering techniques for the enhancement and recognition of the geologically significant lineaments, as well as algebraic operations with band ratios and Principal Component Analysis (PCA), for the identification of alteration zones. Statistical rose diagrams and a SCHMIDT projection Stereo Net were generated from the lineament maps and the collected field ...
The influence of MeV electrons irradiation on the gate oxide layers of hydrogenated polysilicon thin film transistors (TFTs) was investigated by measuring gate leakage currents and threshold voltages. The experimental data revealed a decrease of oxide trap density and increase of positive oxide charge. Improvement in the interface roughness and in the oxide quality near the bottom interface was observed.
The influence of MeV electrons irradiation on the gate oxide layers of hydrogenated polysilicon thin film transistors (TFTs) was investigated by measuring gate leakage currents and threshold voltages. The experimental data revealed a decrease of oxide trap density and increase of positive oxide charge. Improvement in the interface roughness and in the oxide quality near the bottom interface was observed.
We report on the fouling of Focused Ion Beam (FIB)-fabricated silicon oxide nanopores after exposure to tap water for two weeks. Pore clogging was monitored by Scanning Electron Microscopy (SEM) on both bare silicon oxide and chemically functionalized nanopores. While fouling occurred on hydrophilic silicon oxide pore walls, the hydrophobic nature of alkane chains prevented clogging on the chemically functionalized pore walls. These results have implications for nanopore sensing platform design.
By means of ESCA the composition and the thickness of passive films formed on austenitic stainless steels were investigated after the attack of nitric acid at various temperatures and acid concentrations. The outermost layers of the oxide film consist of SiO_2, then a layer rich of Cr-oxid follows, containing also some Mo in the four- and sixvalent state. Ni does not contribute to the oxide film. Cr is also enriched in the metal just below the oxide film. (orig.).
The RKR potential energy curves are constructed for the ground states of diatomic hafnium oxide and thorium oxide. Using Lippincott and Hulburt-Hirschfelder potential function the dissociation energies are estimated by curve fitting method. The H-H potential function was found to give a better fit in both cases. The dissociation energies of hafnium oxide and thorium oxide are estimated as 9.04 #+-# 0.02 eV and 10.34 #+-# 0.01 eV respectively. (author).
Samples dredged from the sediment mounds have a unique chemistry and mineralogy which reveals details of the hydrothermal processes that produce these deposits. The mounds form primarily by deposition of Fe, Mn and Si from hydrothermal fluids which circulate through the basalt crust and the overlying sediments. The Mn, Fe and Si are strongly fractionated in the process; the Fe and Si precipitate within the mounds under slightly reducing conditions as nontronite, while the Mn is deposited as Mn oxyhydroxides at the seawater-sediment interface. The nontronite is exceptionally well crystallized, and contains less than 200 ppm Al. The Mn minerals, todorokite and birnessite, also have exceptional crystallinity and the distribution of trace elements Cu, Ni, Zn, Co, Ca and Ba in these phases agrees with predictions made on the basis of models of their crystal structure. The environment of deposition which produces this suite of minerals - slow ...
The main objectives of this study was to determine the bone density for the purposes of i) determining the age of peak bone mass in each study group and ii) quantifying the differences in bone density as functions of age and sex. The results of estimating the age dependence of mineral density for the femoral neck, spine and total body of healthy women and men using DEXA are given. The age changes in concentrations of major minerals and electrolytes found for compact and trabecular bones of healthy male femoral neck with regard for the wet and dry tissue calculations are represented. Information about femoral neck water content depending on the age of healthy men is tabulated. The number of performed observations and analyses is evidently insufficient to make any final decision, however some preliminary conclusions can be drawn. In accordance with DEXA results, BMD maximum for the femoral neck, spine and total body of healthy women is found for ...
Identifying stable isotope variation and mineralogical changes in fractured rock may help establish the history of climatic and geomorphological processes that might affect the isolation properties of a waste repository site. This study examines the use of the stable isotope ratios of oxygen ({sup 18}O/{sup 16}O) and carbon ({sup 13}C/{sup 12}C) in authigenic minerals as hydrogeochemical tools tracing low-temperature rock-water interaction in variably-saturated fractured stuff. Isotopic compositions of fracture-filling and rock matrix minerals in the Apache Leap tuff, near Superior, Arizona were concordant with geothermal temperatures and in equilibrium with water isotopically similar to present-day meteoric water and groundwater. Oxygen and carbon isotope ratios of fracture-filling, in unsaturated fractured tuff, displayed an isotopic gradient believed to result from near-surface isotopic enrichment due to evaporation rather than the effects ...
Many data mining tools cannot be used directly to analyze the complex sets of relations which are found in large database systems. In our experience, data miners rely on a well-defined data model, or the knowledge of a data expert, to isolate and extract candidate data sets prior to mining the data. For many databases, typically large legacy systems, a reliable data model is often unavailable and access to the data expert can be limited. In this paper we use reverse engineering techniques to infer a model of the database. Reverse engineering a database can be seen as knowledge discovery in its own right and the resulting data model may be made available to data mining tools as background knowledge. In addition, minable data sets can be produced from the inferred data model and analyzed using conventional data mining tools. Our approach reduces the data miner`s reliance on a well-defined data model and the data expert.
A new microdensitometry method for quantitative assessment of bone mineral content using Fuji computed radiography (FCR) was developed and the results were compared with those obtained by the conventional film-screen method. Using both methods, X-ray pictures of the 2nd metacarpal bone were taken with a reference aluminum step wedge in nine normal subjects and nine parameters representing the width and density of bone marrow and cortex were calculated in middle of the bone shaft. Interobserver reproducibility assessed for three parameters was significantly higher in the FCR method than the conventional one. The value of {Sigma}GS computed by the FCR method, that is equivalent to the net bone density of the transverse section of the shaft, showed higher correlation with the one obtained by computed tomography in comparison with the conventional method. In our FCR method, moreover, interobserver reproducibility and accuracy was improved by employing automatic ...
A new microdensitometry method for quantitative assessment of bone mineral content using Fuji computed radiography (FCR) was developed and the results were compared with those obtained by the conventional film-screen method. Using both methods, X-ray pictures of the 2nd metacarpal bone were taken with a reference aluminum step wedge in nine normal subjects and nine parameters representing the width and density of bone marrow and cortex were calculated in middle of the bone shaft. Interobserver reproducibility assessed for three parameters was significantly higher in the FCR method than the conventional one. The value of #SIGMA#GS computed by the FCR method, that is equivalent to the net bone density of the transverse section of the shaft, showed higher correlation with the one obtained by computed tomography in comparison with the conventional method. In our FCR method, moreover, interobserver reproducibility and accuracy was improved by employing automatic ...
The mobility of metals in ground water is an important consideration for evaluating remedial options at the Asarco smelter site. Tacoma, Washington. One factor in assessing metal mobility is the degree of secondary mineralization in a slag-fill aquifer extending into the intertidal zone along the Puget Sound shoreline. Samples of aquifer material were collected for mineralogical analysis from borehole MW-206 at five-foot intervals within the slag fill from 5 to 25 feet below the ground surface, and in the underlying marine sand and gravel at 27 feet. Grab samples of slag fragments with visually apparent secondary minerals were also collected at five intermediate depths between 12 and 19 feet. Samples were analyzed by a variety of techniques including hydride generation/atomic absorption for arsenic concentration, scanning electron microscopy/electron microprobe for mineralogical texture and microanalysis, powder x-ray diffraction for ...
The optimizing criterion is assumed to be the maximum net present value of the project. The following summarizes the significant conclusions. (1) Over a large range of discount rates, mining and milling of the mineral deposit at a constant cutoff grade and a constant production rate consistently results in smaller annual discounted cash flows than the optimal schedule determined by the dynamic programming model (dpm) where the cutoff grade and mining rate are allowed to vary in response to fluctuating product price. (2) With an increasing discount rate, under the dpm the annual discounted cash flows decrease at a slower rate than if the mineral inventory is mined and milled at a constant cutoff grade and a constant production rate. (3) Cuttoff grade increases only where higher equity ore is available. Thus, to maintain the mill feed requirement, the mining rate also increases. (4) Not withstanding an anamolous mineral ...
Objectives To clarify the relationship between bone mineral density (BMD) and body composition in Japanese women aged 18?40?years with low forearm BMD. Methods The subjects were Japanese199 women who had been selected for inclusion in the study based on a low forearm BMD determined at the Annual Women?s Health Examination. The subjects? mean (? standard deviation) age, body height, body weight, and body mass index (BMI) were 33.5 (?4.3) years, 158.1 (?5.1) cm, 49.6 (?5.7) kg, and 19.8 (?2.1), respectively. The BMD of the lumbar spine, total body, and left arm were measured using dual-energy X-ray absorptiometry (DXA). Fat mass (FM), bone-free lean tissue mass (LTM), and body fat percentage (BF%) were measured simultaneously with DXA. Results In the structural equation model, the standardiz...
Environmental research related to uranium tailings is being carried out within the Mining Research Laboratories and Mineral Sciences Laboratories of CANMET, EMR. Field-related research on uranium tailings has been conducted at Elliot Lake for over five years. Much of the work has been focused on a program to rehabilitate pyritic tailings. This has resulted in developing a practicable technology for growing vegetation on such wastes. Limitations have been small size of the test-plots and the relatively short period during which experiments have been carried out. A research program aimed at identifying and reducing acidic and radioactive effluents is also underway at Elliot Lake. These liquid effluents have been identified as the most serious threat to the environment. Research at the Mineral Sciences Laboratories and its predecessor divisions relating to the processing of uranium and thorium ores is outlined. A process has been developed for ...
Aqueous mineral carbonation is a potentially attractive sequestration technology to reduce CO2 emissions. In this paper, the energy consumption and costs of this technology were assessed using either wollastonite (CaSiO3) or steel slag as feedstock. The major energy-consuming process steps were found to be the grinding of the feedstock and the compression of the CO2. Within ranges of experimentally investigated process conditions, optimum energetic CO2 sequestration efficiencies were 79 and 74% for wollastonite and steel slag, respectively. It was shown that the energetic performance for both feedstock might be improved up to >90% by e.g. further grinding of the feedstock and reducing the amount of process water applied. At energetically optimized process conditions, a preliminary cost estimate was made of 93 and 66 euro/ton CO2 avoided for wollastonite and steel slag, respectively (sequestration costs excluding possible capture). For wollastonite, major ...
The effect of sodium on the partial oxidation of methane over MoO{sub 3}-SiO{sub 2} in the presence of molecular oxygen has been investigated. As in the sodium-free case, the major products are formaldehyde, carbon monoxide, carbon dioxide, and water. Kinetic analysis indicates that methane is directly oxidized to formaldehyde and carbon dioxide. Formaldehyde is oxidized to carbon monoxide, which is itself further oxidized, providing an alternative route to carbon dioxide. The kinetic model shows that sodium poisons the direct oxidation of methane to formaldehyde and carbon dioxide, but promotes the oxidation of formaldehyde and carbon monoxide. Model predictions of rates and selectivities are in good agreement with the experimental data. A mechanism that explains both the poisoning and promotion effects of sodium on MoO{sub 3}-SiO{sub 2} is proposed.
Targets for heterogeneous transmutation of americium are composed of a support material, the inert matrix and of an americium oxide compound: AmO{sub 2-x} or Am{sub 2}O{sub 3}. In parallel to the studies using americium, simulated compounds of americium oxide, chosen amongst lanthanide oxides, are used. The selection of these compounds is based on theoretical, physical and crystallochemical considerations. In order to assess the influence of impurities composed of lanthanide oxides, resulting from the separation process, on the physical and chemical properties of such a target, synthesis of oxide powders containing impurities associated with the simulated americium oxide, characterizations, crystallographic studies and sodium compatibility tests have been performed. (author)
Titanium oxides were grown anodically to selected final potentials on grade II polycrystalline titanium under different anodization rates. XPS and RBS results show that the oxide consists of primarily TiO2 with a non-stoichiometric oxide/metal interface, with the slower growth rate associated with a thicker layer at the interface. Characterization using TEM reveals that the structure of the oxide evolves from a primarily amorphous phase to islands of crystallites in an amorphous matrix, to an entirely crystalline phase by increasing the polarization potential. Slower growth rates tend to remain crystalline at higher potentials. The mechanical strength of oxide films extracted from load-depth data by nanoindentation varies dramatically for oxide films grown by different rates at 9.4 V, and to a lesser extent at lower potentials. The variation of film strength is ...
Desulphurization of gasoline and kerosene was carried out using organic and inorganic oxidants. Among the organic oxidants used were hydrogen peroxide in combination with acetic acid, formic acid, benzoic acid and butyric acid, while inorganic oxidants used included potassium permanganate and sodium perchlorate. The oxidation of each petroleum oil was carried out in two steps; the first step consisted of oxidation of the feed at moderate temperature and atmospheric pressure while in the second step, the oxidized mixture was extracted with azeotropic mixture of acetonitrile-water. A maximum desulphurization has occurred with NaClO4 and hydrogen peroxide and acetic acid, which are 68% and 61%, respectively in case of gasoline and 66% and 63%, respectively in case of kerosene oil. The FTIR st...
Synergism has been observed during inhibiting initiated oxidation of styrene or tetralin by organic phosphites in the presence of complex compounds of some transition metals. The results are given of non-additive intensification of antioxidative activity of triphenylphosphite (TPP) and tri-(4-methyl-6-tert.-- butyl)-phenyl-phosphite (TMBP) in the process of initiated oxidation of styrene or tetralin with addition of acetylacetonates of cobalt and vanadyl. During styrene oxidation, inhibition of the reaction with chelate complex of vanadyl is weakened considerably when phosphite is added into the reaction system. During tetralin oxidation, postcatalytic (or branched) oxidation is observed only for large concentration of vanadyl complex. Addition of TPP to above complex sharply increases the induction period. When the induction period is completed, oxidation of ...
A kinetic model based on the Mars-van Krevelen mechanism that allows to describe the microkinetics of the heterogeneously catalysed partial oxidation of {alpha}, {beta}-unsaturated aldehydes is presented. This conversion is represented by a network, composed of the oxidation of the {alpha}, {beta}-unsaturated aldehyde towards the {alpha}, {beta}-unsaturated carboxylic acid and the consecutive oxidation of the acid as well as the parallel reaction of the aldehyde to products of deeper oxidation. The reaction steps of aldehyde respectively acid oxidation and catalyst reoxidation have been investigated separately in transient experiments. The combination of steady state and transient experiments has led to an improved understanding of the interaction of the catalyst with the aldehyde and the carboxylic acids as well as to a support of the kinetic model assumptions. (orig.)
Our goal was a process to convert methane to higher hydrocarbons oxidatively, since this circumvents thermodynamic yield limits of a strictly degydrogenative process. Keller and Bhasin converted thermodynamic yield limits of a strictly dehydrogenative process. Keller and Bhasin converted methane to higher hydrocarbons by using metal oxides as oxidants, without co-fed oxygen. They stated that selectivity is necessarily poor if gaseous oxygen is present. Jones and Sofranko have also used reducible metal oxides as oxidants in a group of their parents, but later used some of those materials with continuous O{sub 2} feed without much loss of selectivity. Baerns, Lunsford and Otsuka have shown that high selectivity could be possible with co-fed O{sub 2} at least for low O{sub 2} partial pressures, over PbO-A1{sub 2}O{sub 3}, Li-MgO and rare earths. The performance of a group of ...
The oxidative dehydrodimerization of propylene to C/sub 3/-dimers (1,5-hexadiene and benzene) has been examined at 600/sup 0/C and atmospheric pressure using a (Bi/sub 2/O/sub 3/)/sub 0.85/(La/sub 2/O/sub 3/)/sub 0.15/ oxide ion-conducting catalyst in a reactor where a catalyst disk separates a feed of propylene in helium from air. The surface of the disk exposed to propylene was reoxidized not by gaseous O/sub 2/, but by the dissociative adsorption and reduction of dioxygen at the oxidant side of the disk, followed by oxide ion conduction to replace spent lattice oxygen. Selectivity to C/sub 3/-dimers when using lattice oxide migration to reoxidize the catalyst was considerably greater than when O/sub 2/ was added to the propylene feed under the same reaction conditions. This result supports the proposal that lattice oxygen is predominantly involved in the selective ...
Data are presented on the insulating properties and capacitance-voltage (CV) characteristics of metal-oxide-semiconductor (MOS) device-thickness (below approx. 100 nm) native oxides formed by wet thermal oxidation of thin InAlP epilayers lattice matched to GaAs. Low leakage current densities of J=1.4 x 10-9 A/cm2 and J=8.7 x 10-11 A/cm2 are observed at an applied field of 1 MV/cm for MOS capacitors fabricated with 17 nm and 48 nm oxides, respectively. TEM images show that the In-rich interfacial particles which exist in 110 nm oxides are absent in 17 nm oxide films. Quasi-static capacitance-voltage measurements of MOS capacitors fabricated on both n-type and p-type GaAs show that the InAlP oxide-GaAs interface is sufficiently free of traps to support inversion, indicating an unpinned Fermi level. These data suggest that InAlP native ...
This work reports studies of ethanol oxidation on Pt-Sn/C catalysts with nearly the same particle size and identical overall composition having different amounts of oxide and alloyed phases. Results of characterization of physical properties by transmission electron microscopy (TEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC), X-ray photoelectron spectroscopy (XPS), and in situ dispersive X-ray absorption spectroscopy (DXAS) are presented. The variation in the amount of oxide and alloyed phases, promoted by heat treatments in mild temperature conditions, does not produce any significant particle growth. Cyclic voltammetry and oxidation of adsorbed CO in acid medium are used to probe the surface conditions. Data on the electrocatalytic activity towards ethanol oxidation, obtained by potential sweeps and chronoamperometry, are discussed and correlate well with ...
The activity concentrations of potassium, uranium and thorium in minerals and soil samples from a mining site in Ibadan, Southwestern Nigeria were measured using gamma ray spectroscopy method. Effective dose per annum has been calculated from the activity concentrations of dominant gamma-emitting natural radionuclides, potassium, uranium and thorium. Samples collected include minerals (beryl, quartz and feldspar), soil samples from the mining pits, heaps and undisturbed land around the mining site. The activity concentrations of {sup 40}K, {sup 238}U and {sup 232}Th, respectively in Bq kg-1 in the mineral samples were as follows: 1985 +- 16, 4.8 +- 0.9 and 11.8 +- 5.8 for beryl sample, 115.1 +- 27.9, 5.0 +- 1.3 and 6.3 +- 5.0 for feldspar samples and 1421 +- 122, <4.8 and 20.1 +- 3.5 for quartz samples. For the soil samples, the mean activity concentrations of {sup 40}K, {sup 238}U and {sup 232}Th, respectively, were ...
The aim of this paper is to investigate the total ionizing dose (TID) radiation effects on MOS capacitor with nitride/oxide stack gate. The stack gate MOS capacitors are fabricated with 20 nm oxide, 40 nm nitride or 110 nm nitride respectively. Through the analysis of CV curve of the irradiation capacitors, it is found that the degradation of the CV curve is due to a significant increase of interface traps and somewhat smaller oxide charge. It is also shown that the thicker of the nitride, more interface traps and oxide charge will be occurred. (authors)
The procedure of charge-coupled devices (CCD) are investigated by using MOS capacitors for enhancing their ionizing radiation tolerance. Authors have found that the gate oxidation temperature, thickness of SiO_2 gate insulator and high temperature processes after gate oxidation are crucial for determining the radiation tolerance of the devices, and proposed to decrease the thickness of gate insulator, perform gate oxidation at 1000 deg C by means of dry oxidation and minimize the number of high temperature procedure steps after gate oxidation. All stated above is a necessary preparation for priducing radiation hardened charge-coupled devices.
SiSiC is one of selected materials for the thermal chemical hydrogen production IS (Iodine-Sulfur) process at JAERI. SiSiC was tested in boiling sulfuric acid for 1000 hours. The obtained results showed the following facts. The transverse strength was not changed by sulfuric corrosion, high temperature oxidation and oxidation. Silica scale formed on SiSiC by sulfate corrosion and high temperature oxidation had corrosion resistance in boiling sulfuric acid. Bilayer structure of silica scale produced by high temperature oxidation was not affected by sulfate corrosion. (S.Y.).
Mineral deposition or alteration is commonly found at fracture-block interfaces is fissured, geothermal reservoirs. In response to pressure reduction in the fissures such mineralization, if less permeable than the matrix rock, will retard the flow of fluid from the blocks to the fissures and is termed fracture skin in this paper. The problem of fluid flow to a production well in a double-porosity reservoir with fracture skin was analyzed theoretically. One of the findings of the analysis was that fully transient block-to-fissure flow can be approximated by pseudo-steady state flow if fracture skin permeability is sufficiently low. Type curves generated by numerical inversion of Laplace transform solutions are used to cooroborate the results of a finite-difference model of steam transport to a well in a naturally fissured, geothermal reservoir with fracture skin.
Nano- and microstructured surfaces are known to impact on the binding and differentiation of cells, but the detailed basic understanding of the underlying regulatory mechanisms is still scarce, which impedes the rational design of smart biomaterials. Towards a comprehensive analysis of the interplay between topographical parameters such as feature design and lateral and vertical dimensions we here report on a combinatorial screening approach, BioSurface Structure Array (BSSA) of test squares each with a distinct topography. Using such BSSA libraries of 504 topographically distinct surface structures, we have identified combinations of size, gap and height of structures which enhance mineralization as well as the expression of osteogenic markers of a preosteoblastic murine cell line. This g...
'Glass Earth' represents a number of current and planned projects within CSIRO aimed at making 'transparent' the top 1000 m of the Earth's crust It builds upon current technologies developed within a number of CSIRO divisions as well as the Australian Mineral Exploration Technologies CRC (AMET CRC), the Australian Geodynamics CRC (AG CRC) and the CRC for Landscape Evolution and Mineral Exploration (CRC LEME). New geophysical and geochemical technologies will be developed to complement these, together with new capabilities in modelling, data integration and visualisation, including hydrogeochemistry, hydrogeology, surface geochemistry and isotope geochemistry, modelling of chemical, fluid and heat flows in rock and regolith, advanced visualisation and data fusion. This paper describes some recent work in the field of isotope geochemistry, with the principal aim of 'seeing through' cover to understand basement geology and detect hidden ore ...
Abstract The following article from the Journal of Tissue Engineering and Regenerative Medicine, -Effects of Pro-inflammatory Cytokines on Mineralization Potential of Rat Dental Pulp Stem Cells- by Yang X, Walboomers XF, Bian Z, Jansen JA, Fan M, published online on 11 July 2011 in Wiley Online Library (), has been retracted by agreement between the authors, the journal Editor-in-Chief, and John Wiley & Sons, Ltd. The retraction has been agreed due to two authors (Walboomers XF, and Jansen JA) not having been involved in the research described, nor made aware of their names being listed on the manuscript, nor told of its submission to the journal.
The Canada Centre for Mineral and Energy Technology (CANMET) is a research organization dedicated to the advancement of the Canadian mining industry. It specializes in the development of new technologies and the coordination of scientific partnerships in the fields of mines, metallurgical processes, and the environment. CANMET supports a number of research and development activities related to the mining industry. In this poster presentation, the author described the mandate of CANMET by first introducing the organization chart with a special emphasis placed on the Mining and Mineral Sciences Laboratories. A description of the different types of partnerships was included, followed by specific details concerning all the projects related to the mining industry, such as terrain control, automation of mines, underground mining environment, processes and services, analytical support, environmental programs, mine effluent, waste rock and tailings, ...
In order to promote uniformity between jurisdictions, the Australian Radiation Protection and Nuclear Safety Agency (ARPANSA) has developed the National Directory for Radiation Protection, which is a regulatory framework that all Australian governments have agreed to adopt. There is a large and diverse range of industries involved in mining or mineral processing, and the production of fossil fuels in Australia. Enhanced levels of naturally occurring radionuclides can be associated with mineral extraction and processing, other industries (e.g. metal recycling) and some products (e.g. plasterboard). ARPANSA, in conjunction with industry and State regulators, has undertaken a review and assessment of naturally occurring radioactive material (NORM) management in Australian industries. This rev...
The report constitutes a first bibliographic study defining the environments the most adapted to the geological mineral in-situ sequestration of CO{sub 2}. For each environment the lithology and the rocks permeability and porosity are analyzed. Thus the possible rocks and deposits in France are presented. (A.L.B.)
The photocatalyzed degradation of pyridine in the gas phase was investigated using titanium dioxide semiconductor supported on mordenite. The complete mineralization was found to occur over a catalyst containing 75 wt% TiO{sub 2} and 25 wt% mordenite in about 180 min in the presence of saturated water vapor at O{degrees}C (4.6 Torr). Low water vapor pressure of 0.096 Torr was found to be sufficient to achieve a reasonably high percentage and rate of degradation. Diffusion of pyridine within the catalyst adversely affects the activity when the thickness of the catalyst coating exceeds the penetration depth of illumination. The activity of the zeolite-supported catalysts was higher than that of TiO{sub 2}. The photonic efficiency for the complete mineralization of pyridine to CO{sub 2} was determined to be 0.48. 29 refs., 6 refs., 1 tab.
Papers from 3 separate conferences are given. The international coal conference covered: advances in control technologies; advances in remote sensing and monitoring; financing and marketing for the future; global climate; health and safety technology; and improving coal's image. Papers from the international minerals and metals conference covered; environmental challenges; financial trends; industry forecast; management strategies; technology advancement; and trade in a changing world. The U.S. issues conference discussed: access to public lands - can you mine if you can't look; innovative technologies in coal mining; innovative technologies in minerals and metals; managing human resource issues; management - controlling costs into the 21st century; and mine waste and water issues.
High-energy synchrotron x-ray diffraction (XRD) has been used to quantify load transfer in bovine plexiform bone. By using both wide-angle and small-angle XRD, strains in the mineral as well as the collagen phase of bone were measured as a function of applied compressive stress. We suggest that a greater proportion of the load is borne by the more mineralized woven bone than the lamellar bone as the applied stress increases. With a further increase in stress, load is shed back to the lamellar regions until macroscopic failure occurs. The reported data fit well with reported mechanisms of microdamage accumulation in bovine plexiform bone.
Electrostatic beneficiation of dry coal has received significant attention in the last decade. In this process the coal is ground and then charged, either by corona charging or by triboelectrification (friction charging). Coal and minerals receive different levels of charge -- often opposite polarities in the case of triboelectrification -- and can then be separated based on differences in electrical mobility. Problems associated with the techniques include rapid deposition of particles on the electrodes, thus, effecting further separation. The goal of this project is to optimize the electrostatic coal cleaning process to remove pyrites and inorganic materials through studies of the electrostatic properties of powdered coal, in-situ measurements of the electrodynamics of coal and mineral particles inside the separator, and development of self-cleaning collector plates for continuous separation.
A fragmented fossil bone incised with the figure of a proboscidean was recently found at Vero Beach, Florida near the location where Late Pleistocene fauna and human bones were recovered from 1913 to 1916. This engraving may represent the oldest and only existing example of Terminal Pleistocene art depicting a proboscidean in the Americas. Because of the uniqueness, rarity, and potential antiquity of this specimen, caution demanded that a variety of tests be used in an attempt to verify its authenticity. The mineralized bone was identified as mammoth, mastodon, or giant sloth. Rare earth element analysis was consistent with the fossil bone being ancient and originating at or near the Old Vero site (8-IR-9). Forensic analysis suggests the markings on the bone are not recent. Optical microsc...
The study was conducted during 2000 to determine the role of various chemical plant factors viz., total minerals, nitrogen, fat contents, carbohydrate, macro an micro nutrients in the leaves of five genotypes of sugarcane i.e., BF-162, SPSG-26, L-118, CP-43/33 and CP-72/2086 by correlating the infestation of top borer, Scirpophaga Nivella F. at tillering stage. None of the genotype was found completely resistant to the pest. CP-43/33 and BF-162 proved susceptible and resistant varieties, respectively. Total mineral, manganese and copper contents did not show significant correlation with the pest infestation, whereas nitrogen, potassium, calcium, magnesium and ferrous contents played a positive and significant role. Phosphorous, carbohydrates, fats and zinc contents played a significant and negative effect on the pest infestation at tillering stage. (author)
The Jaduguda U (?Cu?Fe) deposit in the Singhbhum shear zone has been the most productive uranium deposit in India. Pyrite occurs as disseminated grains or in sulphide stringers and veins in the ore zone. Veins, both concordant and discordant to the pervasive foliation, are mineralogically either simple comprising pyrite ? chalcopyrite or complex comprising pyrite + chalcopyrite + pentlandite + millerite. Nickel-sulphide minerals, though fairly common in concordant veins, are very rare in the discordant veins. Pyrite in Ni-sulphide association is commonly replaced by pentlandite at the grain boundary or along micro-cracks. Based on concentrations of Co and Ni, pyrite is classified as: type-A ? high Co (up to 30800?ppm), no/low Ni; type-B ? moderate Co (up to 16500?ppm) and moderate to high ...
Natural minerals and some industrial wastes are used as low cost sorbents for removal of metal ions from effluent streams. Apatite as natural mineral and red mud as an industrial waste have been tested for their sorption properties with respect to two important fission products "1"3"7Cs and "9"0Sr. Their ion exchanging capacity was tested after every 4 hours till 24 hours. The material gets saturated after 4-8 hours. Hence these materials can be considered for treating in treating LLW before discharge, industrial waste treatment and as backfill or admixture material for shallow land repository. (author)
Cathodic arc deposition is an established and industrially applied technique for the formation of nitrides (e.g. TiN); it can also be used for metal oxide thin film formation. A cathodic arc plasma source with the desired cathode material is operated in an oxygen atmosphere of appropriate pressure, and metal oxides of various stoichiometric composition can be formed on different substrates. We report here on a series of experiments on metal oxide formation by cathodic arc deposition for different applications. Black copper oxide has been deposited on accelerator components to increase the radiative heat transfer between the parts. Various metal oxides such as tungsten oxide, niobium oxide, nickel oxide and vanadium oxide have been deposited on ITO glass to form electrochromic films for window ...
With an objective to learn reactivity of coal at its surface, surfaces of oxidized coal samples were investigated. Miike coal was oxidized by using {sup 18}O2 in a closed loop system. As the reaction progresses, proportion of CO2 including isotopes increased rapidly as a result of oxidation of CO sites existing in the coal and the newly generated C{sup 18}O sites. The oxidizing reaction progressed via oxygen adsorbing sites generated near the surface, and oxygen containing groups. An FT-IR analysis estimated the depth of the oxidized layer to be 10{mu}m or less from particle surface. The oxidized coal was pulverized to see its surface condition. Functional groups introduced by the oxidation enter into the vicinity of the surface in a form to desorb as CO. CO2 is trapped in inner pores. The coal surface was observed by using an atomic force ...
Zirconium and particularly Zr-2.5wt%Nb (Zr2.5Nb) alloy are useful for engineering bearing applications because they can be oxidized in air to form a hard surface ceramic. Oxidized zirconium (OxZr) due to its abrasion resistant ceramic surface and biocompatible substrate alloy has been used as a bearing surface in total joint arthroplasty for several years. OxZr is characterized by hard zirconium oxide (oxide) formed on Zr2.5Nb using one step thermal oxidation carried out in air. Because the oxide is only at the surface, the bulk material behaves like a metal, with high toughness. The oxide, furthermore, exhibits high adhesion to the substrate because of an oxygen-rich diffusion hardened zone (DHZ) interposing between the oxide and the substrate. In this study, we demonstrate a two step pro...
In recent years, the influences of acid rain such as the acidification of lake water, on bio-system by the heavy metals from effluent of soils with acid rain and also on the structural materials of buildings are seriously discussed. Sulfur and nitrogen that are contained in fossil fuels are released into the atmosphere by the fuel combustion as their oxides dissolve in rain drops as sulfite and nitrous ions, where they are further oxidized into sulfate and nitrate ions These ions lower the pH of rain water resulting so-called acid rain. Therefore, it is important to accurately determine these ions in rain water for the investigation of reality of acid rain. However, it is not easy to accurately determine these ions, especially for sulfite ions in rain water, since they are quickly oxidized by the catalytic action of metallic ions such as ferric and manganous ions. And light, temperature, pH of solution and also species and ...
The oxide colloidal route, developed in the laboratory for mono-metallic catalysts, consists in preparing a metallic oxide hydro-sol which leads to the supported catalyst after deposition onto a support and an activation stage. In this work, this method has been adapted to the preparation of alumina supported bimetallic Pd-Sn catalysts to determine its interest for the control of the properties of the bimetallic phase (size, composition and structure). In the preliminary study concerning tin oxide sols, SnO{sub 2} (size=2,3 nm) and Sn{sub 6}O{sub 4}(OH){sub 4} (size = 25 nm) nano-particles were synthesized by neutralization respectively for tin(IV) and tin(H). The control through the pH of the aggregation of the PdO and SnO{sub 2} particles revealed that increasing oxide solubility promotes integral re-dispersion of the oxide particles. To synthesize oxide ...
The construction materials used in coolant systems in nuclear power plants become covered with oxide films as a result of exposure to the aqueous environment. The susceptibility of the materials to different forms of corrosion, as well as the extent of the incorporation of radioactive species on the surfaces of the primary circuit, are greatly influenced by the physical and chemical properties of these oxide films. The composition and characteristics of the oxide films in turn depend on the applied water chemistry. This work was undertaken in order to collect and evaluate the present views on the structure and behaviour of oxide films formed on iron- and nickel-based materials in aqueous environments. This survey should serve to recognise the areas in which more understanding and research effort is needed. The review begins with a discussion on the bulk oxides of iron, nickel and ...
The formation of thin SiO_2 layers on silicon and metal silicides was studied by phase- and thickness measurements with Rutherford back-scattering of 2 MeV alfa particles. Thermal oxidation was done in steam and dry oxygen at temperatures between 750 degrees Celsius and 1 100 degrees Celsius, while SiO_2 formation at room temperature was carried out by anodic oxidation. The study of silicon oxidation was done on Si<100>, Si<111> and amorphous silicon substrates. Thermal oxidation of CoSi_2, CrSi_2, NiSi_2, PtSi and TiSi_2 was investigated. The oxidation rates of the silicides were found to be much higher than for silicon. The oxidation process is also diffusion-limited with a higher oxidation rate for steam as compared to dry oxygen. The silicide layers were found to stay intact during thermal oxidation. A ...
This work presents the spectroscopic results of the investigations of ancient pottery remains excavated in ancient Kremna (BURDUR-TURKEY). The micro-Raman and FT-IR spectroscopic studies of the pottery remains belonging to sixth century allowed us to identify the mineral composition. Some examples are described of the use of this technique in the field of art conservation and diagnostics, with regard to pigments, and some products of metal alteration.
This report presents information and analysis to assist BLM in clarifying oil shale research needs. It provides technical guidance on research needs in support of their regulatory responsibilities for onshore mineral activities involving oil shale. It provides an assessment of research needed to support the regulatory and managerial role of the BLM as well as others involved in the development of oil shale resources on public and Indian lands in the western United States.
The effects of a moderate-intensity static magnetic field (SMF) on osteoporosis of the lumbar vertebrae were studied in ovariectomized rats. A small disc magnet (maximum magnetic flux density 180 mT)...Full Text Available
The right upper lung lobe of a 74 year old man was resected for a central tumour. Two primary cancers were found; a central small cell carcinoma and a peripheral squamous cell carcinoma. In addition,...Full Text Available
Papers are presented under the following topics: machine control and automation; rock drilling; cutting and fragmentation; rock characterization, remote sensing and interface detection; artificial intelligence and mine monitoring systems; computer applications; mechanical excavators; material handling; surface and underground mining; innovative mining systems; new developments in mechanical miners; ground hazard detection and control; ground support; and extraterrestrial mining.
Papers are presented under the session headings: research in mechanical fragmentation; rock characterization, remote sensing and interface detection; monitoring, data transmission and communications; tunnel boring machines; minewide monitoring and expert systems for ground control; machine guidance; shaft and raise boring; automation of drilling equipment; machine automation and control; new developments in mechanical miners; materials handling; innovative mining systems; general minewide monitoring and expert systems; ground support; human factors; and extraterrestrial mining.
The topics covered at the conference include: mineral exploration; geological mapping/stratigraphy; environmental monitoring and hydrology; petroleum exploration; radar digital elevation mapping; new commercial remote sensing initiatives; geological hazards and engineering; processing and integration techniques; and hyperspectral geology.
A hydrocarbon composition having a major portion of a hydrocarbon preferably a lubricating oil such as mineral oil and at least a friction-reducing amount usually 0.01 to 10 weight percent of an amine or amine derivative of a hydrocarbon-soluble polymerized fatty acid e.g. a dimeramine derived from a dicarboxylic acid containing at least 12 carbon atoms such as 9(10)-carboxy stearic acid has improved antifriction and flue economy properties.
Phonon relaxation and internal friction in kaolin-and bentonite-filled PVC composites are studied. By varying the temperature and/or content of the ultrafine mineral filler in the PVC, one can control the contribution from phonon viscosity, damping force, and the effect of viscosity into the energy dissipation of ultrasonic oscillations in the MHz frequency interval. The dynamic character of the measurements makes it possible to differentiate between relaxation phenomena in the composites and to suggest methods for their controlled changes.
The Nova Scotia Research Foundation Corporation was established in 1946 by the Province of Nova Scotia to use science and technology to assist in the economic development of Nova Scotia. Within the Applied Science Division of the Corporation, research and development programs in the area of coal and mineral technology have been undertaken. A brief description of two projects -- coal liquefaction and coal-water fuels, are reported.
Daily exposures of adult beagle dogs to inhaled radon daughters plus uranium ore dust, with and without concurrent cigarette smoking, for 2 to 5-1/2 yr have produced massive pulmonary fibrosis and severe emphysema. The cumulative exposure doses are similar to those associated with a 5-fold or greater increase in death rate of uranium miners due to chronic respiratory insufficiency, including pneumoconiosis, pulmonary fibrosis, and emphysema.
The use of filters of activated-charcoal particles in drinking-water purification plants assists in the elimination of organic micropollutant substances. The authors report on a study which sought to investigate the mechanism of organic matter; they describe the experimental programme, which used different size ranges of mineral-based activated charcoal, present the experimental findings and discuss the results. 16 references.
A numeric method for predicting mineral ash deposition in coal dust furnaces is presented which is based on a bidirectional working time coupling of thermodynamic calculation routines (ChemApp{sup TM}) with the commercial CFD code FLUENT{sup TM}. The deposition characteristics of particles and wall surfaces is assessed on the basis of evaluations of flow simulation parameters and results of thermodynamic calculations for the mineral matter contained in the fuel particles, taking into account the complete energy, momentum and mass exchange history of the ash and the mineral conversion. The models enables calculations of the gaseous release of mineral components (e.g. alkaline substances and chlorine) from ash during combustion and its distribution inside a combustion chamber. The method and model are validated using experimental data. (orig.) [German] In der vorliegenden Arbeit wird ein numerisches ...
This report highlights the significance of the geological sciences to the nation and to society. Discussions include understanding plate tectonics and surface processes, exploring the continental crust, ocean basins and the deep earth, applications of geology to social problems such as mineral resources, waste disposal, siting of critical facilities, geological hazards, water resources management, and coastal zones. The state of health of geological research is also discussed. (ACR)
This book presents the papers given at a symposium on occupational safety in coal mines. Topics considered at the symposium included human factors, causes and prevention of personal injuries, remote sensing for ground control, respirable dust generation by continuous miners, accident analysis, hazard analysis of mining equipment, coal mine blasting accidents, coal mine respirable dust sampling, and noise in the mining industry.
Key elements in strategic planning in the nonferrous mining industry are discussed. Included are price forecasting, financial planning, government relations, research and development, and exploration. Financial planning is discussed in terms of 1) forecasting of earnings, 2) investment policy and 3) tax planning. Costs of environmental liabilities are expected to have a major impact on the industry. (JMT)
The gastrointestinal absorption of lead was markedly increased in human subjects who had fasted before ingesting lead. Food in the gut was found to reduce lead absorption, and the effect of dietary constituents on /sup 203/Pb absorption was investigated. The greatest reduction in absorption was caused by minerals. This dependence of lead absorption on dietary constituents complicates the establishment of safe levels of lead in food and water.
Physico-chemical studies were carried out on a sample of red mud collected from NALCO, Orissa, after calcination up to 1,200 C at an interval of 100 C. The observed change in properties like surface area, particle size, bulk density and mineral phases etc., can be profitably used while finding an appropriate application of this polluting waste from alumina plants.
We investigated the descriminative ability of total body bone-mineral expressed as the total body bone-density (TBBD) measured by dual photon absorptiometry (DPA) in 79 healthy premenopausal women, 27 healthy postmenopausal women, and 120 female osteoporotic fracture patients presenting with either Colles' fracture, vertebral fracture or femoral neck-fracture. TBBD was compared to the bone-mineral density of the lumbar spine (BMD{sub spine}) also measured by DPA, and to the bone-mineral content of the forearms (BMC{sub forearm}) measured by single photon absorptiometry (SPA). TBBD, BMD{sub spine} and BMC{sub forearm} showed that all the fracture patient groups had significantly reduced bone-mass. Using receiver operating characteristic (ROC) analysis, we found that TBBD had a tendency towards better discriminative ability than BMD{sub spine} or BMC{sub forearm} with regard to the discrimination between healthy ...
The question about expanding the boundaries of the open pit mining method is examined. The use of methods which consider the advantages of open and underground mining operations with their joint use in horizontal and evenly dipping deposits will make it possible to objectively select the mining method, to expand the range of use of open pit mining operations in the deposits of the Far North and provide an improvement in the technical and economic indicators of mineral extraction.
In this lesson you will learn about density and why some things float and others sink. Imagine you and a friend are on a camping trip. As you walk along a stream, your friend notices some shiny gold rocks. You pick them up wondering if they are real gold nuggets. Your friend remembers there is a mineral that looks like gold, "fools gold", or pyrite. The density of ...
...Box Contains One Month Supply Dietary supplement with a premium patented formula of L-Arginine, Ginseng, Ginkgo plus 13 essential vitamins, antioxidants, and minerals to support male sexual function . ArginMax for Male Sexual Fitness is a patented combination of l-Arginine, Ginseng, Ginkgo, and 13 essential vitamins and ...
The nature of interaction of some boromagnesium minerals with water is studied, the main stages of interaction are established. The methods of thermo-gravimetric, X-ray phase and chemical analyses are applied to state intermediate and final phases of magnesium borate interaction with water. ''Preobrazhenskite'' - ''inderite'' paragenesis is established. The notion ''magnesium borate solubility'' is shown to be senseless.
... However blaming vitamin supplements on deaths, or mortality is silly, as the studies are not exactly kosher. Vitamin C in 2,000mg is good for allergies, and niacin (b3) in 10,0000mg is good for depression. This is all examples on how vitamin supplements can help. I call it a security blanket, as food these days is not so good due vitamin and mineral damage due to light, or storage. By the time we eat the apple from the supermarket, there is minimal vitamin and ...
A cross sectional study on the mineral density of the 3rd lumbar vertebral trabecular bone was carried out in 123 children less than 15 years old, comprising 44 controls, and 79 patients affected with conditions which are at risk for developing metabolic derangement of skeletal bone (34 patients taking antiepileptic drugs (AED), 29 undergoing glucocorticoid (GC) therapy and 16 bedridden patients), by using quantitative computed tomography (QCT) with a CaCO{sub 3} phantom. Serum Ca and alkaline-phosphatase (Alp) levels were measured at the time of QCT examinations in all. The results obtained were as follows: The QCT values in the control children showed neither age dependency nor a sexual difference before puberty. The QCT values in each group showed significant difference with one another; the control group>the AED group>the GC group>the bedridden group (p<0.05{approx}0.005). The serum Ca levels in each pathology group were significantly lower than ...
...take on my Notice of Intent to Conduct Geothermal Resource Exploration Operations? ...INTERIOR MINERALS MANAGEMENT (3000) GEOTHERMAL RESOURCE LEASING Exploration Operations...take on my Notice of Intent to Conduct Geothermal Resource Exploration Operations?...
The morphological development of oxide scales formed on a low Al substituted #beta#-sialon (z=0.2) oxidised for time periods up to 1024h at 1350 C is discussed in relation to oxidation kinetics. The oxidation process is observed to be accompanied by changes in both the phase assemblage of the external layers and their morphology. Thus as the time of oxidation increases beyond 64h the cristobalite-#beta#-yttrium disilicate phase assemblage changes to cristobalite plus #beta#- and #gamma#-yttrium disilicate. In addition to the changes observed for the surface layers, differences are observed in the morphologies of the polished cross-sections. These changes are consistent with an order of magnitude decrease in oxidation rate. (orig.).
Regularities of deformation-induced dissolution of a surface layer of iron oxides in matrixes of iron-based alloys with bcc and fcc lattices have been studied by the methods of M?ssbauer spectroscopy, transmission electron microscopy, and X-ray diffraction. A method of producing iron alloys strengthened by dispersed oxide nanoparticles and alloyed with elements possessing a high affinity to oxygen (titanium and yttrium) has been proposed, which implies a dynamic dissolution of a surface layer of iron oxides upon strong cold deformation and a precipitation of secondary yttrium and titanium nanooxides upon a subsequent high-temperature sintering of mechanically alloyed powders. There has been demonstrated a possibility of oxide strengthening of pure iron upon its interaction with air without...
MCrAlY coatings are widely used on hot section components of gas turbines to provide hot corrosion and/or oxidation protection by formation of an oxide layer on the surface. As the protective oxide scale exfoliates during service, aluminum from the coating diffuses outward for reformation of the protective scale. Aluminum may also diffuse inward due to the differences in composition between the coating and the substrate. Thus, the coatings degrade due to oxidation, oxide scale spallation, and inward and outward diffusion of aluminum. Service life of these coatings is controlled by the aluminum content in the coating, operating temperature and start- shutdown cycles. In-service degradation of CoCrAlY and CoNiCrAlY coatings is presented. A procedure to predict the remaining service life of coatings under oxidizing conditions is discussed. (orig.) 12 refs.
Determination of the specific surface of uranium oxides: UO_2 and U_3O_8 using a simplified equation derived from the Brunauer, Emmett and Teller theory. The method is suitable for samples having a surface between 6 to 50 m"2.
PurposeHeavy metals and other forms of oxidative stress have been implicated as key factors in the formation of age-related cataract in humans. Metallothioneins are...Full Text Available
Reactive oxygen species (ROS), inevitable byproducts of aerobic metabolism, are known to cause oxidative damage to cells and molecules. This, in turn, is widely accepted as a pivotal determinant of...Full Text Available
Altered structure, and hence function, of cellular macromolecules caused by oxidation can contribute to loss of physiological function with age. Here, we tested whether the lifespan of bats, which generally...Full Text Available
The influence of surface oxides of variable composition and nonstoichiometry formed at high temperatures in air on the general corrosion resistance of ferritic chromium steel type 08H17T (Fe-17Cr-1Ti) in weak sulfuric acid has been studied. Anodic passive films formed on steel with different pretreatments have also been examined. The surface oxide of nearly stoichiometric composition formed at 300 C provides for the passive state of steel in sulfuric acid despite its depletion by chromium when compared with that for nonstoichiometric Cr-enriched oxide formed at 600 C. The dissolution and transformation of nonstoichiometric thermal surface oxide in sulfuric acid appear to take place through defect sites, {minus}Fe{sup 2+} ions, and oxygen vacancies of the n-type conductor. The passive film formed on the nonstoichiometric oxide film, which had been produced at 600 C, was found to be ...
BackgroundFree nitric oxide (NO) reacts with sulphydryl residues to form S-nitrosothiols, which act as NO reservoirs. We sought to determine whether thiol-preserving...Full Text Available
The purpose of this study was to synthesize biocompatible polyvinylpyrrolidone (PVP)-coated iron oxide (PVP-IO) nanoparticles and to evaluate their efficacy as a magnetic resonance imaging (MRI)...Full Text Available
A catalytic process for the oxidation of sulfur-containing gases , E.G., sulfur dioxide and simultaneous production of sulfuric acid wherein a sulfur-containing gas is reacted with an oxygencontaining gas in the presence of a catalyst comprising an iron group metal on a solid support comprising a zeolite in a silicaalumina matrix.
4-Hydroxynonenal (HNE), a major electrophilic product of lipid peroxidation, is regarded as both a marker of oxidative stress and a mediator of oxidative damage. At subtoxic concentrations,...Full Text Available
The gelation kinetics of an in situ gelable hydrogel formulated from oxidized dextran (Odex) and N-carboxyethyl chitosan (CEC) were investigated rheologically. Both Schiff base...Full Text Available
It is shown analytically and experimentally that thermally stimulated current (TSC) measurements at negative bias incompletely describe oxide-trap charge in SIMOX and bipolar base oxides irradiated at 0 V. Positive-bias TSC is also required.
Rheological properties of moderately concentrated solutions of cellulose in methylmorpholine N-oxide-dimethylformamide mixtures containing hydrophilic montmorillonite nanoparticles were studied. Film composite materials were prepared, and their physicomechanical properties and structural organization were studied.
It has been discovered that iron(III) chloride complexes supported on activated charcoal oxidize phosphine under normal conditions. The process accelerates as the concentration of the chloride ions and the proton acid increases.
We report the use of cysteine-substituted mutants in conjunction with in situ oxidation to determine the physical proximity of a pair of engineered cysteines in the pore region of the voltage-gated...Full Text Available
A series of in situ gelable hydrogels were prepared from oxidized dextran (Odex) and N-carboxyethyl chitosan (CEC) without any extraneous crosslinking agent. The gelation readily...Full Text Available
A multidisciplinary approach was used to study the effects of pollution from a marine fish farm on nitrification rates and on the community structure of ammonia-oxidizing bacteria in the underlying...Full Text Available
This study was conducted to determine by gas chromatography (GC) and mass spectrometry (MS) the identity and the quantity of volatile N products produced during the helium-purged in vivo...Full Text Available
The OH-initiated photo-oxidation of n-butane was used as a source of 1- and 2-butoxy radicals. Reactions producing ketones and other organic compounds are explained. Rates of photolysis were determined and are discussed.
Because copper catalyzes the conversion of H2O2 to hydroxyl radicals in vitro, it has been proposed that oxidative DNA damage may be an important component of copper toxicity....Full Text Available
Oxidative stress has been implicated in the etiology of age-related muscle loss (sarcopenia). However, the underlying mechanisms by which oxidative stress contributes to sarcopenia have not been thoroughly...Full Text Available
The authors investigate the possibility of the direct heterogeneous catalytic synthesis of ethylbenzoate from benzonitrile. The catalysts tested were oxides of aluminium, titanium, and vanadium. The main conversion product detected chromatographically was ethylbenzoate; benzaldehyde, benzamide, and benzanilide were also identified. Aluminium oxide was found to be the most effective catalyst.
Neurons in the hippocampal CA1 region are particularly sensitive to oxidative stress (OS), whereas those in CA3 are resistant. To uncover mechanisms for selective CA1 vulnerability to OS, we...Full Text Available
The neuronal nitric oxide synthase gene (NOS1) is located at 12q24, a susceptibility region for schizophrenia, and produces nitric oxide (NO). NO has been reported to play important...Full Text Available
Quantitative probing of heterogeneous regions in muscle is feasible with phosphorus-31 magnetic resonance spectroscopy because of the differentiation of metabolic patterns of glycolytic and oxidative...Full Text Available
Thermophilic propionate-oxidizing, proton-reducing bacteria were enriched from the granular methanogenic sludge of a bench-scale upflow anaerobic sludge bed reactor operated at 55°C with a mixture...Full Text Available
Bacterial nitric oxide synthases (bNOS) are present in many Gram-positive species and have been demonstrated to synthesize NO from arginine in vitro and in vivo. However, the physiological role...Full Text Available
BackgroundClara cell protein (CC16), the main secretory product of bronchiolar Clara cells, plays an important protective role in the respiratory tract against oxidative stress and...Full Text Available
The oxidation conditions were investigated for obtaining a higher productivity in the production of high strength carbon fiber from polyacrylonitrile (PAN). The effect of incorporation of 2 % comonomer such as methyl acrylate (MA), acrylate containing carboxylate (SA), acrylamide (AAm), and hydroxyethyl acrylate (HEA) on the oxidation conditions was also investigated. The measurement of DSC and bonded oxygen content revealed that the most effective comonomer for promoting the cyclization of nitril group and the bonding of oxygen was found to be SA, and the second best was AAm. The measurement of tensile strength of carbon fiber showed that the copolymer of SA, HEA, and MA gave a high strength fiber. It took a long time to oxidize the carbon fiber when it was oxidized at a temperature on which double layer structure was not formed. To shorten the production time, a method of combining the upper limit ...
BackgroundTrichloroethylene (TCE) may induce oxidative stress which generates free radicals and alters antioxidants or oxygen-free radical scavenging enzymes.MethodsTwenty...Full Text Available
Systemic administration of lipopolysaccharide (LPS), which causes endotoxemia and systemic inflammation, has been reported to induce expression of the gene for type II inducible nitric oxide synthase...Full Text Available
Three nucleic acid probes, two for autotrophic ammonia-oxidizing bacteria of the beta subdivision of the class Proteobacteria and one for alpha subdivision nitrite-oxidizing bacteria, were developed...Full Text Available
The electrochemical behavior of lanthanide oxides in molten alkaline chloride media is of great concern in pyrochemical processes for advanced nuclear fuel cycle. We have studied the solubilities of various lanthanide oxides in LiCl-KCl eutectic melt. In general, lanthanide oxides appeared to be insoluble/sparingly soluble in LiCl-KCl eutectic at 723 K. However, europium oxide exhibited an abnormal behavior in solubility and redox chemistry. The solubility of europium oxide was measured to be 1-2 order of magnitude higher than those of other lanthanide oxides. This abnormal solubility may be attributable to different electrochemical behavior of europium in the same experimental conditions. Most lanthanides ion exists as trivalent oxidation states. However, we observed divalent europium dissolved in LiCl-KCl molten salt by applying electron ...
1. The effect on rat liver peroxisomal beta-oxidation of feeding diets containing various amounts of dietary oils was investigated. With increasing amounts (5-25%, w/w) of soya-bean oil an apparent,...Full Text Available
This patent describes a method comprising applying a passivation layer of CaF{sub 2} to the surface of a superconductive ceramic oxide by evaporation. The CaF{sub 2} layer is effective to passivate the oxide surface without disrupting the superconductive properties.
Suspensions of denitrifying cells of Pseudomonas perfectomarinus reduced nitrate and nitrate as expected to dinitrogen; but, in the presence of acetylene, nitrous oxide accumulated when nitrate or nitrate...Full Text Available
There is increasing evidence of a biochemical link between lipid oxidation and bone metabolism. Paraoxonase 1 (PON1) prevents the oxidation of low-density lipoprotein (LDL) and metabolizes biologically...Full Text Available
BackgroundArsenic (As) exposure during pregnancy induces oxidative stress and increases the risk of fetal loss and low birth weight.ObjectivesIn...Full Text Available
Anionic peroxidase from tomato (Lycopersicon esculentum) fruit oxidized indoleacetic acid (IAA) slowly in the presence of Mn2+ and dichlorophenol in acetate buffers. The...Full Text Available
The aim of the present study was to evaluate the ameliorative potential of quercetin (QC) against paracetamol (PCM)-induced oxidative stress and biochemical alterations in mice blood. A total of 36...Full Text Available
Evolution of nitrogen oxides (NO(x), primarily as nitric oxide) from soybean (Glycine max [L.] Merr.) leaves during purged in vivo nitrate reductase assays...Full Text Available
Increased oxidative stress with elevated levels of reactive oxygen and nitrogen species (ROS/RNS) plays an important role in the pathophysiology of many disease states. Increased ROS/RNS can...Full Text Available
A detection theory is developed for point-contact metal-oxide-metal (MOM) systems. A system with heterogeneous oxide strongly bonded to the substrate is considered. It is shown that the form of the functional connection between the barrier heights and the ultimate compressive strength of the oxide has no substantial influence on the voltage-current characteristics of the system. Quantitative analysis indicates that a MOM system can behave as a tunnel diode and as a diode with a Schottky barrier. The model permits the determination of the optimum construction of long-life detectors based on MOM point-contacts.-
This paper reports on hydrolysis of 10 metal salt aqueous solutions of 6 metal oxides that was conducted in supercritical water. Continuous and rapid production of metal oxide fine particles was achieved by mixing a metal salt aqueous solution with preheated water fed from another line. The reaction time required was less than 2 min. Particle size, morphology, and crystal structure of the obtained metal (hydrous) oxides were examined. Particle size (20 to 600 nm) was different among the system but the size range was relatively narrow in all the cases.
Partial oxidation of 2-propanol was carried out on AB{sub 1-x}B`{sub x}O{sub 3} (A=Ba, B=Pb, Ce, Ti; B`=Bi, Sb and Cu) type perovskite oxides. Acetone was the major product observed on all the catalysts. All the catalysts underwent partial reduction during the reaction depending on the composition of the reactant, nature of the B site cation and the extent of substitution at B site. The catalytic activity has been correlated with the reducibility of the perovskite oxides determined from Temperature Programmed Reduction (TPR) studies. (orig.)
Green River oil shale was air oxidized at subretorting temperatures. Off gases consisting of nitrogen, oxygen, carbon monoxide, carbon dioxide, and water were monitored and quantitatively determined. A mathematical model of the oxidation reactions based on a shrinking core model has been developed. This model incorporates the chemical reaction of oxygen and the organic material in the oil shale as well as the diffusivity of the oxygen into the shale particle. Diffusivity appears to be rate limiting for the oxidation. Arrhenius type equations, which include a term for oil shale grade, have been derived for both the chemical reaction and the diffusivity.
... Title : Effect of Yttrium on the Microstructure of Titanium Alloys,. ... The yttrium was added in the melting stage as an oxide or in the elemental form. ...
Objective of the project is characterization of electrode reactions in molten salt by using metal oxides and silica-based electrode. The scope of project are characterization of metal oxide properties in molten salt and miniaturization of 3-electrode electrochemical test cell. Electrochemical micro-cell for actinide-LiCl-KCl molten salt was newly designed. Electroless and electrochemical deposition technique was applied to Mo coating on quartz tube. From the design of electrode and 3-electrode electrochemical cell suitable for the tests in molten salt electrolyte, so it is anticipated to get the information on the electrochemical behavior of metallic electrode in molten salt and to secure the information on oxidation/reduction behavior of actinide
Measurements were completed on the solubility of cupric and cuprous oxides in liquid water and steam at controlled pH conditions from 25 to 400 C (77 to 752 F). The results of this study have been combined with those reported from this laboratory in two previous EPRI reports to provide a complete description of the solubility of these oxides and the speciation of copper dissolved in liquid water and steam as a function of oxidation state, temperature, pH, and in the case of steam, pressure. These constitute the first set of reliable data for cuprous oxide solubility over this range of conditions. For the more intensively studied CuO case, agreement was found between our results and those of previous studies of its solubility in steam, whereas only partial agreement was evident for its solubility in liquid water. For both oxides this disagreement often amounted to orders of ...
Thermal wet oxidations of GaP and Al{sub 0.4}Ga{sub 0.6}P at 650 degree sign C for various times have been performed. Comparisons are made on oxidation rates and post oxidation morphology. Transmission electron microscopy shows that when oxidizing GaP, polycrystalline monoclinic GaPO{sub 4}{center_dot}2H{sub 2}O forms without noticeable loss of phosphorus. Oxidation for 6 h or more leads to poor morphology resulting in cracks and detachment. A thickness expansion of about 2.5-3 times is noticed as a result of oxidation. In contrast, oxidized Al{sub 0.4}Ga{sub 0.6}P exhibits much better morphology without cracks or detachment from the substrate. The oxide has an almost amorphous-like microstructure. The oxidation process shows typical diffusion-limited reaction at long anneals. Preliminary work on the ...
This articles deals with an approach that has given some key information about the mechanisms of the liquid phase oxidation of butane to acetic acid. This procedure has been developed over the last 34 years; however, much of what will be discussed represents a synthesis of previous insights. Many of the observations are relatively recent and have not been previously published. In principle, this approach should be applicable to many oxidation processes. (orig.)
The behaviour of an elastomeric seal for vehicle brake Tandem master cylinder is measured and analyzed in temperature and brake fluids changed. Working conditions are simulated for different piston rod velocity and cylinder supply pressure, in temperature rising, brakefluid boundary and Nanoaluminum oxide brakefluid oxide brakefluid lubrication. The result shows that Nanoaluminum oxide brakefluid with its ball shape can highly reduce friction coefficient to avoid seal excessive wear and reduce slick slip in brake applications.
The application of kinetic probes that allow one to determine relative reactivities of biologically relevant substrates with oxidizing intermediates in the Fenton reagent (H2O2 plus Fe2+ in acidic aqueous...Full Text Available
A two-step purification protocol was used in an attempt to separate the constitutive NAD(P)H-nitrate reductase [NAD(P)H-NR, pH 6.5; EC 1.6.6.2] activity from the nitric oxide and nitrogen dioxide (NO(x))...Full Text Available
The authors have determined quantitative characteristics for oxide films forming on (111) surfaces of cadmium telluride single crystals on anodic oxidation in 0.1 M KOH: the constants in the Guenterschulze-Betz equation and the film growth constant, which is 2.4 nm/V, from which the activation energy for cadmium telluride electrooxidation has been calculated.
The following methods of quartz ceramics alloying were considered: alloying of initial quartz glass; introduction of alloying additive into water slip of quartz glass; porous materials impregnation with salt aqueous solutions and subsequent salt thermal decomposition with formation of stable oxides in pores of ceramics. Oxygen free compounds BN, SiB_4, SiC, Si_3N_4, REM oxides and transition metal oxides were used as alloying additives. Main properties of the materials and compositions obtained are presented.
During electrolysis of a "2"4"8Cm(III) solution in 2M K_2CO_3 at pH=13, partial oxidation of curium to a higher oxidation state, probably Cm(IV), was observed. The absorption spectra of Cm(III) and Cm(IV) in K_2CO_3 solution were recorded and the molar extinction coefficients of main absorption bands of curium were evaluated. (author).
Oxide catalysis plays a central role in hydrocarbon processing and improvements in catalytic activity or selectivity are of great technological importance because these improvements will translate directly into more efficient utilization of hydrocarbon supplies and lower energy consumption in separation processes. An understanding of the relationships between surface structure and catalytic properties is needed to describe and improve oxide catalysts. Our approach has been to prepare supported oxides that have a specific structure and oxidation state and then employ these structures in reaction studies. Our current research program is focused on studying the fundamental relationships between structure and reactivity for two important reactions that are present in many oxide-catalyzed processes, partial oxidation and carbon-carbon bond formation. ...
AQ4N (1,4-bis([2-(dimethylamino-N-oxide)ethyl]amino)5,8-dihydroxy- anthracene-9,10-dione) is a novel alkylaminoanthraquinone N-oxide which, on reduction, forms a stable DNA affinic cytotoxic compound...Full Text Available
For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO2, PrO2), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two sha...
Coordination of CoCl2 solutions to the silica polyamine composite, WP-1, made with the branched polymer polyethylenimine (PEI) shows irreversible binding resulting from surface oxidation of the Co2+-Co3+. This is not the case for the silica polyamine composite BP-1 made with the linear polymer polyallylamine where reversible binding and no oxidation is observed. These observations suggested that oxidation of the cobalt was related to the greater coordination number available with the branched polyamine relative to the linear polyamine. A study of the kinetics of cobalt binding to WP-1 indicated initial loading of Co2+ at relatively low coordination number followed by desorption of Co2+ leading to oxidation and irreversible binding. Exclusion of oxygen from the composite-cobalt solution mix...
The invention is regeneration and recirculation of nitrogen oxides in the exhaust gas of a nitric acid plant without using any material current and heat energy other than that generated in the process of producing nitric acid. Nitrogen oxide is recovered by at least two adsorbers each containing an acid resistant zeolite molecular sieve and operating in an alternate heat cycle; adsorption occurring at 20-40 degrees C and regeneration at 300-350 degrees C. The hot gas exiting from the oxidation U used in the production of nitric acid is used to regenerate the adsorbers and the nitrogen oxides set free during the said regeneration are introduced into the main feed stream of the nitric acid plant. In the final stage of the regeneration the adsorbers are cooled by rinsing them with exhaust gas or air at a temperature of 20-40 degrees C.
#beta#-sialon ceramics of equal overall compositions but containing amorphous, partly crystalline and almost completely crystalline intergranular phase(s) have been oxidized in oxygen at 1350 deg C for 20 hours. The obtained weight gain curves do not follow the parabolic rate law (#DELTA#W/A_0)"2= k_pt + #beta#. To the extent that crystallization occurs in the oxide scale during the oxidation experiment, the amorphous cross section area through which oxygen most easily diffuses will decrease with time. A brief description of this new rate law is given, and the obtained oxidation curves will be discussed within that framework. 4 refs., 2 tabs., 2 figs.
Chemical modification of poly(?-caprolactone) PCL by oxidation with potassium permanganate in solution was investigated. According to the data obtained from Fourier transform infrared spectroscopy (FT-IR) and nuclear magnetic resonance 1H NMR, after the oxidation reactions the PCL chains exhibited new functional groups (vinyl and hydroxyl) and possible intermolecular recombination, producing an oxidized-polycaprolactone (PCL-OX). Solution viscometry indicated that degradation also occurred during the oxidation reactions (30% drop in viscosity average molecular weight was detected). Differential scanning calorimetry (DSC) also indicated that PCL was chemically modified and degraded. The successive self-nucleation/annealing (SSA) treatment confirmed that a reduction (or interruption) in line...
One-electron oxidation of several derivatives of pyrazolin-5-one, including the drug antipyrine, were studied by pulse radiolysis of aqueous solutions. All the compounds were found to be oxidized by Br2 rapidly but considerably more slowly by weaker oxidants, such as peroxyl radicals. From redox equilibria using p-methoxyphenol and N,N,N',N'-tetramethyl-p-phenylenediamine as reference compounds, the one-electron oxidation potentials of the methyl-substituted 2-pyrazolin-5-ones were found to be in the range of 0.32-0.39 V versus normal hydrogen electrode. The relevance of these findings to the properties of the drug nafazatrom is discussed. Antipyrine was found to have a much higher oxidation potential, estimated as 1.2-1.5 V, which is rationalized on the basis of the phenyl substitution and lack of resonance stabilization of the radical cation.
The chemical composition and the semiconducting properties of passive films formed on nickel based alloy (Alloy 600) in acidic sulphate solution, pH 2.0 at room temperature were studied using Auger analysis, voltammetric techniques and the Mott-Schottky approach. The results obtained revealed that the presence of both chromium and mixed nickel-iron oxides in the films leads to the development of a p-n heterojunction, which controls their electronic structure, similarly manner to the case of stainless steels and Alloy 600 in borate buffer solution. This behavior has been interpreted as representing of an oxide system, which has a duplex character, with an inner p-type semiconducting region, mainly formed by chromium oxide and an outer n-type semiconducting region, containing iron oxide. It could also be observed that the nickel oxide present in the films acts as a barrier layer ...
The chemical composition and the semiconducting properties of passive films formed on nickel based alloy (Alloy 600) in acidic sulphate solution, pH 2.0 at room temperature were studied using Auger analysis, voltammetric techniques and the Mott-Schottky approach. The results obtained revealed that the presence of both chromium and mixed nickel-iron oxides in the films leads to the development of a p-n heterojunction, which controls their electronic structure, similarly manner to the case of stainless steels and Alloy 600 in borate buffer solution. This behavior has been interpreted as representing of an oxide system, which has a duplex character, with an inner p-type semiconducting region, mainly formed by chromium oxide and an outer n-type semiconducting region, containing iron oxide. It could also be observed that the nickel oxide present in the films acts as a barrier layer ...
The paper discusses two petrochemical selective oxidation reactions namely the practised formation of styrene (STY) and the desired oxidative functionalisation of propane. The present knowledge about the mode of operation of oxide catalysts is critically considered. The dehydrogenation of ethylbenzene (EB) should be described by an oxidehydration with water acting as oxidant. The potential role of the coke formed during catalytic reaction as co-catalyst will be discussed. Selective oxidation is connected with the participation of lattice oxygen mechanism which transforms unselective gas phase oxygen into selective oxygen. The atomistic description of this process is still quite unclear as well as the electron structural properties of the activated oxygen atom. The Role of solid state acidity as compared to the role of lattice oxygen is much less well investigated modern ...
Transient experiments in a Temporal Analysis of Products (TAP) Reactor were performed to elucidate the role of surface oyxgen species in the oxidation of benzene to phenol on ZSM-5 type zeolites with nitrous oxide as a selective oxidant. It was shown by puls experiments with nitrous oxide that the mean lifetime of the generated surface oxygen species is between 0.2s at 500 C and about 4.2 s at 400 C. Afterwards the surface oxygen species desorb as molecular oxygen into the gas phase where total oxidation will take place if hydrocarbons are present. Dual puls experiments consisting of a nitrous oxide puls followed by a benzene puls allowed studying the reactivity of the surface oxygen species formed during the first puls. The observation of the phenol formation was impeded due to the strong sorption of phenol. Multipulse experiments were necessary to reach a ...
A thermal analyzer-differential scanning calorimeter-mass spectrometer (TG-DSC-MS) was used to study oxygen carriers (OC) for their potential use for the application of chemical looping combustion (CLC) to solid fuels. Reaction rates, changes in reaction rates with repeated oxidation-reductions, exothermic heats during oxidation, and the effect of changing reduction gas compositions were studied. Oxidation rates were greater than reduction rates and reaction rates were reproducible through multiple oxidation-reduction cycles except where agglomeration occurred with powders. Iron oxide (Fe{sub 2}O{sub 3} powder) and iron-based catalysts were found suitable for CLC of solid fuels having rapid reduction rates which increased with higher reducing gas concentrations. Fe{sub 2}O{sub 3} powder was used to oxidize a high carbon coal char in an inert gas removing 88% of ...
Slurry aluminizing is one method of protecting titanium alloys and intermetallics at temperatures at which oxidation would otherwise significantly degrade mechanical properties. The technique produces a continuous layer of alumina-forming TiAl_3 on exposed surfaces. The influence of composition, film thickness, and diffusion temperature upon the oxidation resistance of these slurry aluminides was studied in cyclic tests to 816degC (1500deg F). Degradation of slurry aluminized #beta#-titanium alloy and #alpha#-Z titanium aluminide intermetallic occurs by localized oxidation at cracks in the coating layer. These cracks are probably due to mismatch of coefficients of thermal expansion between the coatings and substrates. Addition of silicon to the slurry modifies the oxidation behaviour around a crack by introducing a continuous layer of titanium silicide at the boundary of the aluminide coating and ...
Finding environmentally friendly and cost-effective methods to remediate soils contaminated with polycyclic aromatic hydrocarbons (PAHs) is currently a major concern of researchers. In this study, a series of small-scale semi-continuous extractions - with and without in situ wet oxidation - were performed on soils polluted with PAHs, using subcritical water (i.e. liquid water at high temperatures and pressures, but below the critical point) as the removal agent. Experiments were performed in a 300 mL reactor using an aged soil sample. To find the desorption isotherms and oxidation reaction rates, semi-continuous experiments with residence times of 1 and 2 h were performed using aged soil at 250 deg. C and hydrogen peroxide as oxidizing agent. In all combined extraction and oxidation flow experiments, PAHs in the remaining soil after the experiments were almost undetectable. In combined extraction and ...
A duplex surface treatment technique based on calorizing and plasma nitriding was developed to improve the wear and oxidation resistance of H13 steel at high temperatures. The effects of the relative thickness of the calorized layer to the depth of plasma nitriding on the wear and oxidation properties at temperatures up to 900 C were investigated in this work. High-temperature wear tests were performed at 500 C with dry conditions in open air using a ball-on-disk type tribotest machine. Isothermal oxidation tests were performed at 900 C for up to 100 h under controlled atmosphere. The results indicated that the specimens with a calorized layer as an intermediate phase between the surface duplex layer and the base metal showed higher wear and oxidation resistance than the specimens with a nitrided layer alone. During exposure to elevated temperatures, the aluminum in the calorized layer diffused to the ...
Papers are presented on the development of oxidation- and sulfidation-resistant ferritic alloys; the microstructural stability of sulfidation-resistant FeCrAl stainless steels around 500 C; age hardening in Fe-Mn-Al-C austenitic alloys; the oxidation/corrosion behavior of low-Cr Fe-Cr-Ni alloys containing Zr or Nb; the high temperature oxidation/corrosion of iron-based superalloys; and the role of Mo in the Na/sub 2/SO/sub 4/ induced corrosion of superalloys at high temperature. Topics discussed include the effect of variations of Co content on the cyclic oxidation resistance of selected Ni-base superalloys; high temperature oxidation of Fe based alloys; the morphological development of high temperature oxide scales of Fe-Mn-Al base alloys; and the oxidation of an Fe-Mn-Al-C alloy at 1000 C. Consideration is given to the corrosion properties ...
Despite the rapid development of literature pertaining to fundamental (1-4) studies of oxidation catalysis, a general theory of heterogeneous selective oxidation catalysis explaining the selectivity behavior of different metal oxide systems has not yet been developed. Redox mechanisms have been widely invoked in the kinetic and mechanistic descriptions of selective oxidation reactions, suggesting a dynamic behavior of hydrocarbon and oxygen interactions with the catalyst surface. Nevertheless, most of the recent theoretical approaches of this subject matter (5-7) are essentially static in nature. Correlations are made with surface structure on the basis of crystallographic considerations with selectivity being related to the nature, number, bond-strength and nearness of oxygen atoms in the neighborhood of adsorption centers. The effect of the reaction medium on the configuration of the catalyst surface, ...
An automated Time Resolved Aerosol Collector (TRAC) has been developed for sequential sampling of field-collected aerosols for laboratory-based Computer Controlled Scanning Electron Microscopy/Energy Dispersed X-ray (CCSEM/EDX) single particle analysis. The collector is optimized for use of grid-supported 20 nm carbon films as deposition substrates. The carbon films have low enough X-ray background to permit EDX analysis down to 0.1-0.2 ?m particles, including detection of low-Z elements: C, N, & O. The TRAC provides unattended sampling onto a set of 151 individual grids, at sequential time intervals as short as 1 min. After collection, the samples are sealed and refrigerated pending analysis. The utility of the TRAC-CCSEM/EDX approach is exemplified using the aerosol samples collected during the Texas 2000 Air Quality Studies (Aug. 15 ? Sept. 15, 2000). We are able to quantitatively follow the time evolution in the relative contribution of non-volatile particles such as ammonium ...
Experimental investigations have been shown that the thermal stability of carnallite shows a clear change to hogher temperature with increasing pressure if the decomposition atmosphere is not removed. Around 40 bar, constitutional water is released from the carnallite lattice at 139/sup 0/C, around 100 bar at 145/sup 0/C. The available temeprature data on thermal release of constitutional water in carnallite (80 to 110/sup 0/C) are not relevant to the possible heat load in a final-storage salt done as all investigations have been carried out in vacuum or in open systems under atmospheric conditions. The author's investigations show the decomposition temeprature of carnallite will be much higher under in-situ conditions with blocked or delayed removal of decomposition atmosphere. However, this applies only to carnallite as isolated mineral phase. Final statements cannot be made until the pressure-temperature stability of carnallite in paragenesis with ...
Two hazard risk assessment matrices for the ranking of occupational health risks are described. The qualitative matrix uses qualitative measures of probability and consequence to determine risk assessment codes for hazard-disease combinations. A walk-through survey of an underground metalliferous mine and concentrator is used to demonstrate how the qualitative matrix can be applied to determine priorities for the control of occupational health hazards. The semi-quantitative matrix uses attributable risk as a quantitative measure of probability and uses qualitative measures of consequence. A practical application of this matrix is the determination of occupational health priorities using existing epidemiological studies. Calculated attributable risks from epidemiological studies of hazard-disease combinations in mining and minerals processing are used as examples. These historic response data do not reflect the risks associated with current exposures. A method using ...
Analyses of the roles of cement-based barriers in radioactive waste isolation show that models used to estimate their characteristics during the lifetime of the repository must consider the alteration of material properties with time due to degradation processes. Reinforced concrete barriers at repositories shall be designed in such manner that they fulfil besides isolative capabilities also the required functions of mechanical resistance and stability. Key elements of safety evaluation are mainly the correct selection of materials for mineral composites with cement binder (cements, aggregates, mineral additives and chemical admixtures) and their design, execution of construction works and production of precast concrete containers (continuous casting of concrete - no cold joints, limited number of construction joints, proper placing and consolidation, finishing and curing), strict control of used materials and inspection of works, as well as ...
Stroke-prone spontaneously hypertensive rats (SHRSP) induce spontaneous osteoporosis. To elucidate the specific characteristics of bone metabolism, the SHRSP was compared with age matched Wistar-Kyoto (WKY) rats. We investigated the effects of prolonged swimming exercise training on bone mineral density (BMD) and metabolism in the SHRSP. Seven-week-old male SHRSP and WKY were divided into three groups; the sedentary control WKY group (n = 6, WKY), the sedentary control SHRSP group (n = 6, SP) and the swimming exercise training SHRSP group (n = 6, SWIM) (in pool with 60 min./day, 5 days/week for 12 weeks). The femoral BMD, bone mineral content (BMC), strength, Ca and P contents (%) of SHRSP were approximately 17, 27, 25, 20 and 9%, respectively, lower than that of WKY (p swimming exercise training in the SHRSP induces more cruelly hypophosphatemia, and leading to osteopenia eventually. We conclude that SHRSP induces osteopenia with disturbance ...
With the exception of some minerals, the specific activity of natural radioactive material is below 370 Bq/g, their handling thus not being subject to authorization or the duty of reporting according to section 4 para. 2 of the Radiological Protection Ordinance. Moreover, there is required no handling license for prospecting, mining and processing of radioactive minerals; they are subject to the procedures for the plans of operation of the mining laws of the Federal States. License-free handling of natural radioactive material may result in the production of radioactive waste, the disposal of which must be authorized according to sect. 47 of the Radiological Protection Ordinance if the specific activity exceeds the free amounts of column 4 in Table IV of Appendix IV by a factor of 10"-"4/g. This inconsistency is discussed by means of the following examples: (1) fly ash and slag from coal power plants, (2) flue dust from sintering plants, (3) ...
Geological clay formations are investigated for use as final underground deposit for heat producing nuclear waste. Special kinds of clay (e.g. bentonite) can also be used for the construction of geotechnical barriers. For the long time safety prognosis of the nuclear waste repositories the development of geochemical transport models is indispensable. The transport of aqueous solutions in clay is a complex process. The three-layer-minerals bentonite and illite swell by the adsorption of water, if the volume is restricted a high swelling pressure develops. The excellent barrier effect of natural clay formations and geotechnical clay barriers is based on the high swelling pressure and the high adsorption capacity for radionuclides and other pollutants. The two-layer-mineral kaolinite has no swelling capacity. In contrast to sandy layers a special geochemical transport potential exists in clay besides the well known matrix potential which ...
A study was carried out to identify optimal laminate/oil combinations for low pressure oil filled and high pressure pipe-type cables, and to establish taping criteria under factory conditions. Laminates from two sources were evaluated in conjunction with Sun XX high viscosity mineral oil and Cosden 015SH polybutene oil for high pressure type cables, and Dussek TC-2288N mineral oil, Shell P2 dedecylbenzene and Chevron DF-100 alkylbenzene for low pressure oil-filled cables. Swelling tests, infrared analysis, dissipation and dielectric measurements, impulse tests and a taping trial were performed. It was found that there is no appreciable difference in performance of both laminates when tested on model cables in a variety of oils. Both types exhibited superior aging characteristics vis-a-vis cellulose paper when tested with a variety of oils and at temperatures up to 105{degree}C. For pipe type cable, high viscosity polybutene is the most suitable ...
Seven types of shellfish were irradiated by gamma ray at doses of 0, 3 and 6 kGy. Pulse photo-stimulated luminescence (PPSL) and thermoluminescence (TL) methods were employed to detect the radiation treatment. The screening of irradiation was carried out by the PPSL method followed by identification using the TL technique. Most of the irradiated shellfish were screened out correctly and only a few showed photon counts a bit higher than the lower threshold value by much lower than the upper threshold value. The TL method was employed using minerals isolated from all the control and irradiated shellfish samples by density gradient treatment. Three parameters, integrated intensities of first glow curves (TL1), ratios of first to that of second glow curves (TL1/TL2), and the shapes of maxima of first glow curves, were utilized for the identification of gamma ray treatment of shellfish. (author)
In the wide range from brown coal to anthracite, an investigation was made of effects of heat treatment on physical/chemical properties and of coal rank dependence. For the experiment, 12 kinds of coal samples were used, and for heat treatment, the fluidized bed heated by the electric furnace and the infrared-ray gold image furnace were used. To examine characteristics of the heat-treated coal char, conducted were oxygen gasification, TPD measurement, XRD measurement, alkali metal measurement, and pore distribution measurement. The following were obtained from the experiment. The gasification reaction rate of the char heat-treated in the temperature range between 900{degree}C to 1700{degree}C decreases with a rise of the temperature of heat treatment, and the degree of decrease in the rate depends on coal rank. The order of gasification rate between coal ranks depends on the temperature of heat treatment, and the lower the heat treatment temperature is, the more largely the ...
Managing public lands for maximum social benefit is becoming an increasingly complex task. The growing need for domestically produced mineral raw materials and energy, and the conflicting interests over the use of public lands, have added new dimensions to the management issues. This report covers the first phase of a long-term program initiated by the Division of State Lands to improve their capability to evaluate the tar-sand and oil-shale resources in Utah. The scope of this phase of the study was limited to examination and analysis of existing information and to development models for data processing and resource evaluation. The study was effective in identifying problem areas and demonstrating the potential value of the proposed systems for management of state lands. It is anticipated that effective evaluation of the oil-shale and tar-sand resources in Utah, supported by readily accessible physical data, will lead to improved management both in policy and in ...
A room-temperature process for stabilizing mineral waste streams has been developed, based on acid-base reaction between MgO and H3PO4 or acid phosphate solution. The resulting waste form sets into a hard ceramic in a few hours. In this way, various alumina industry wastes, such as red mud and treated potliner waste, can be solidified into ceramics which can be used as structural materials in waste management and construction industry. Red mud ceramics made by this process were low-porosity materials ({approx}2 vol%) with a compression strength equal to portland cement concrete (4944 psi). Bonding mechanism appears to be result of reactions of boehmite, goethite, and bayerite with the acid solution, and also encapsulation of red mud particles in Mg phosphate matrix. Possible applications include liners for ponds and thickned tailings disposal, dikes for waste ponds, and grouts. Compatability problems arising at the interface of the liner and the waste are avoided.
In the present work, a rapid deposition anodic stripping voltammetry (ASV) for determination of uranium is presented. For this purpose, the uranyl hexacyanoferrate (K2UO2[Fe(CN)6]) is deposited electrochemically on a thin palladium-aluminum electrode (Pd-Al) from a UO22+ solution in the presence of K3Fe(CN)6. Then, the well stable (K2UO2[Fe(CN)6]) on the electrode was stripped by anodic differential pulse voltammetry for measuring the UO22+ ion concentration. The effect of operational parameters, including: concentration of K3Fe(CN)6, solution pH, deposition potential, and deposition time were studied. In optimum conditions, the calibration graph was linear in the concentration range 105-7 x 10-4 mol L-1 with a detection limit of 6.2 x 10-6 mol L-1. The influence of some concomitant ions in K2UO2[Fe(CN)6] formation was investigated. The proposed method was used for the rapid determination of uranium in some uranium mineral ores. (orig.)
Sialons are phases in the Si-Al-O-N and M-Si-Al-O-N systems where M includes Li, Mg, Ca, Sc, Y and the rare earth elements. They are comparable in variety with the mineral silicates and are built up of one-, two-, and three-dimensional arrangements of (Si,Al)(O,N)/sub 4/ tetrahedra in the same way that the structural units of the silicates are SiO/sub 4/ tetrahedra. These new materials include N-containing ceramics, glasses and glass-ceramics that are being explored for their thermal, chemical and physical properties.
This document contains the Proceedings of the Eleventh Thematic Conference Geologic Remote Sensing (Volume II). The conference was held February 27-29, 1996 in Las Vegas, Nevada, USA. Presentations included in this volume address the following topics: Geologic Remote Sensing and aerial surveying as applied toward mineral exploration, monitoring of geothermal resources, petroleum exploration, the environmental effects of mining, environment and hydrology, detection of geohazards, and the GIS system and data integration. Some information regarding the use of color imagery in remote sensing is also included.
16 papers are presented covering: remote sensing - an aid to environment management; remote sensing application; monitoring environmental changes over iron ore mining areas; monitoring and management of environmental degradation due to geological factors; use of Landsat multispectral scanner data in environmental monitoring; geotechnical engineering problems with abandoned limestone mines; photogrammetric monitoring of mining environment; slope monitoring in open cast mines using close range remote sensing method; geobotanical remote sensing and mineral prospecting; geographical information in study of geo-environment through remote sensing; and alteration mapping in cuprite mining district.
The ultimate compressive strength of 36 thoracolumbar vertebrae was determined experimentally. In addition, the trabecular bone mineral content was measured by single energy quantitative computed tomography. The areas of fractured endplates were also determined by computed tomography. The results show that a linear relationship exists between the compressive strength and the product of bone density and endplate area. These data allow an in vivo prediction of vertebral body strength using a noninvasive method with a standard error of estimate amounting to less than 0.95 kN. PMID:3212488
A mixture of aminoacids was irradiated by a scattered proton beam, its energy varying from 4 to 6.6 MeV, by doses up to 5 x 10"1"1 proton/cm"2 for studying the potentiality of abiogenic synthesis of biologically important compounds in space. It was ascertained that increase in the radiation dose and reduction of proton energy involve increase in effectiveness both of destruction of the initial aminoacid (tryptophan, tyrosine, glycine) and synthesis of the relevant dipeptide. Essential influence of mineral substrate on abiogenic synthesis of natural nucleotides under the action of diverse energy sources was pointed out
Elbistan lignite has been found to contain 50.1 wt% (daf) humic acid. The i.r. spectrum of this lignite, however, indicates the absence of free carboxyl groups. Treatment with mineral acids, however, regenerates the carboxyl groups. A product containing 18.8 wt% N (daf) has been obtained by treatment of HNOat3 treated Elbistan lignite in aqueous ammonia for 4 h at 165 C and under oxygen pressure. Water-soluble and active nitrogen tests indicate that such products may have the properties of slow-release nitrogenous fertilizers. (33 refs.)
Aim of the work was to describe the noninvasive assessment of bone mineral density, geometrical and biochemical properties in premenopausal women with dietary intake of phytoestrogens and comparison of these parameters with those of age-matched female subjects with Mediterranean dietary intake lacking in these substances. Volumetric cortical, trabecular and total mineral density and bone geometrical properties were evaluated with peripheral quantitative computed tomography (pQCT) at the distal radius of the non dominant forearm. pQCT showed higher bone mineral density (total and trabecular) and SSI values in premenopausal with dietary intake of phytoestrogens. Despite the lack of statistical significance, these preliminary results, should further support the few literature findings about the potential role of phytoestrogens consumption in preventing trabecular bone loss. However, further studies are warranted to evaluate ...
Abstract in english Odontopus brevirostris (Hustache, 1936) feeding on Annona squamosa L., A. cherimola Mill., A. glabra L., and A. muricata L. was observed. The last three host plants are recorded for the first time. The endophitic oviposition occurs in the veins of the ventral surface of the young leaves. The larvae, leaf miners, eat the parenchyma and the adults make small holes in the leaves. The pupation occurs in spherical cocoons protected by a sort of nest (pupation chamber) between the two epidermal layers.
Original investigations of ablation of minerals, fullerene-like compounds, polymers and complicated biological macromolecules under the action of submillimeter radiation of the free-electron laser (FEL) developed and built at Budker Institute of Nuclear Physics [V.P. Bolotin et al., First experiments on high-power Novosibirsk terahertz free-electron laser, Budker INP, 2005, p. 37 [1
S. 1484 is intended to change the oil-shale-leasing provisions of the Mineral Leasing Act of 1920 to encourage development of oil-shale resources on federal and non-federal lands. It authorizes the Secretary of the Interior to lease land for mining and additional land for waste-disposal and construction facilities. The text of S. 1484 is followed by the background and legislative history of the bill, a section-by-section analysis of the bill, and an evaluation of its budgetary and regulatory impacts. Pertinent communications are reprinted with recommendations and additional views. (DCK)
Central penetrating excisional wounds were made in the corneas of 12 rabbits and 10 trout. The scar tissue and the surrounding cornea were compared using a new method for assessing inorganic elements in the cornea: the scanning electron microscopy and energy dispersive analysis of x-ray (EDAX). Semiquantitative determination of inorganic elements within the range of atomic numbers 9-93 in the periodic system was performed, comparing the relative concentration of those elements in the scar tissue to the surrounding cornea. Results showed that calcium was the only element higher in the healing wound than in the surrounding cornea.
This paper discusses the remote plugging of leaks in inaccessible pipework, with main reference to small leaks which frequently appear in ancillary cooling water circuits of nuclear reactors. Initially developed to cure problems of the pre-stressed concrete pressure vessels of UK reactors, the ZORIC sealant has been used to repair leaking biological shield pipework on six CANDU reactors. ZORIC is based on a water-soluble epoxy resin and an aqueous suspension of a refined mineral clay. This paper describes the evolution of the sealant, the qualification and testing program, and their application to CANDU reactor systems. 2 refs., 6 figs.
The Uinta Basin is an important hydrocarbon producing area, with extensive resources of hydrocarbon, bitumen, and fossil fuels. Gilsonite, tar sands, oil shale and coal are found in abundance with the cretaceous and Tertiary sedimentary rocks. The 25 papers include discussion on: leasing; thermal maturity of rocks and hydrocarbon deposits; influence of source rock type, thermal maturity and migration on composition and distribution of the natural gas; drilling; geology; structural evolution of gilsonite dykes; reclamation of coal mines; oil shale resources; and uranium mining.
Knowledge of ground subsidence behavior provides for better economic planning and execution of a mining exploitation, higher safety and optimum use of the resources without ruining the environment. In addition, when considering subsidence generated by petroleum exploitation, the monitored (measured) subsidence, combined with geological information and a suitable prediction model, can provide data on the expanse of the oil field and thus aid in the estimation of available resources. An integrated survey system for monitoring mining subsidence is described which has been developed as part of a research program in cooperation with the Canada Centre for Mineral and Energy Technology. (JMT)
The Rosebel gold district is hosted in a Paleoproterozoic greenstone belt of the Guiana Shield and has many characteristics that enable classification of the ores as an orogenic gold deposit. Host rocks have undergone several phases of deformation. However, gold deposition occurred late in the structural history of the belt, and is considered part of a late regional metallogenic event with respect to the geotectonic evolution of the Guiana Shield. Economic gold mineralization is hosted in felsic to mafic volcanic rocks and two sedimentary successions that are differentiated into turbiditic and arenitic depositional packages. The detailed lithostratigraphic characterization and the geochemistry enable the correlation of the local rock types with the Paramaka, the Armina, and the Rosebel for...
... Do you certify Halal or Kosher meat? What fish feed do you allow? What levels of polychlorinated biphenyls (PCBs) have been found in organic fish? How can I be sure that organic products from abroad are really organic? Do you prosecute businesses that break the rules? Does the Soil Association carry out any routine testing of food? Do you test for GM material? Why do you allow additives in organic food? Is organic food fortified with vitamins and minerals? Why choose organic during pregnancy?...
Most important radionuclides naturally appearing in minerals used to form building materials are described. The frequently met ranges of concentrations of these radionuclides in the building materials composed from natural products as well as from power-plant wastes and metallurgic plant wastes are discussed and propositions concerning the limitation of presence of radioactive nuclides in the building materials are given, with special concern paid to materials for dwelling and public utility buildings. The elaborated technique of measuring potassium 40, radium 226 and thorium 228 concentrations is presented. Data on the organization of controlling-and-measuring laboratories in this field are given. (author).
The Committee on Interior and Insular Affairs issued the report on a bill to establish a national program for research, development, and demonstration in fuels and energy and for the coordination and financial supplementation of Federal energy research and development; to establish development corporations to demonstrate technologies for shale oil development, advanced power cycle development, geothermal steam development, and coal liquefaction and gasification development; to authorize and direct the Secretary of the Interior to make mineral resources of the public lands available for the development conporations. Comments from governmental agencies on the bill are published. (MCW)
The report is divided into six working group discussions on the following subjects: 1) Chemical and physical mechanisms in the formation of uranium mineralization, geochronology, isotope geology and mineralogy; 2) Sedimentary basins and sandstone-type uranium deposits; 3) Uranium in quartz-pebble conglomerates; 4) Vein and similar type deposits (pitchblende); 5) Other uranium deposits; 6) Relation of metallogenic, tectonic and zoning factors to the origin of uranium deposits. Each working group paper contains a short introductory part followed by a discussion by the working group members.
Coal slurry pH values can be used to characterize coals. pH values depend on the coal, time since slurry preparation, contact with gas atmosphere, particle size, and stirring. Measured values reflect a sequence of reactions including: carbon dioxide absorption by water from the air, wetting of the coal (pH may be affected by the elemental composition of the mineral matter), and further equilibration with species in the water. The pH initially drops as carbon dioxide is absorbed, then rapidly increases as the coal is wetted, and then slowly decreases as some reactions with species in the water take place.
This report briefly describes the background to colliery engineering maintenance, past experience in machine condition monitoring within coal preparation and the introduction of condition-based maintenance. A role model scheme has been developed for the introduction of condition-based maintenance into coal preparation plants. The report describes the instrumentation and monitoring methods suitable for application to most mineral processing plants, the use of specialist companies to monitor, gather, process and analyse the information and the actions taken by the colliery. Examples of the benefits of operating such a scheme are given in terms of safety, performance and finance. Other problematical aspects of coal processing are examined which have a direct effect on plant condition and availability.
The objectives of this project was to: (1) quantify the pore scale mechanisms that determine the wettability state of a reservoir, (2) study the effect of crude oil, brine and mineral compositions in the establishment of mixed wet states, (3) clarify the effect of mixed - wettability on oil displacement efficiency in waterfloods, (4) develop a new tracer technique to measure wettability, fluid distributions, residual saturation's and relative permeabilities, and (5) develop methods for properly incorporating wettability in up-scaling from pore to core to reservoir scales.
Examples are given of reference materials for radionuclide X-ray fluorescence analysis (RXFA) of the environment processed by the National Bureau of Standards and the IAEA. Methods are described used for preparing standard materials for RXFA. For determining air pollutants the sample is prepared by dry or wet mineralization. Water samples have to be preserved prior to analysis. Insoluble components are separated by filtration or centrifugation. Biological materials must be dehydrated and homogenized. Samples of soil, sludges, sediments and solid wastes will sometimes have to be converted into a solution in some cases a leachate will have to be obtained. (ES).
Bone is a complex, highly structured, mechanically active, three-dimensional (3-D) tissue composed of cellular and matrix elements. We previously published a report on in situ collagen gelation using a rotary 3-D culture system (CG-RC system) for the construction of large tissue specimens. The objective of the current study was to evaluate the feasibility of bone tissue engineering using our CG-RC system. Osteoblasts from the calvaria of newborn Wistar rats were cultured in the CG-RC system for up to 3 wk. The engineered 3-D tissues were implanted into the backs of nude mice and calvarial round bone defects in Wistar rats. Cell metabolic activity, mineralization, and bone-related proteins were measured in vitro in the engineered 3-D tissues. Also, the in vivo histological features of the transplanted, engineered 3-D tissues were evaluated in the animal models. We found that metabolic activity increased in the engineered 3-D tissues during cultivation, and that ...
The differing susceptibility of individuals to the toxic effects of chronic lead exposure has never been fully understood. As the major intake of lead in the human is from food and beverages, any variation between individuals of the quantity of lead absorbed from the gut, and of the distribution and excretion of this lead, may account for the differences in individual susceptibility. The food and beverages themselves may have an influence, and to investigate their effects on absorption, distribution and excretion of lead, experiments were performed on normal subjects using a short lived radionuclide of lead, "2"0"3Pb, and instruments generally available in Nuclear Medicine. Lead absorption between different individuals showed a wide variation when "2"0"3Pb was taken as a single dose between meals. Minerals were found to be mainly responsible for affecting absorption when one subject ingested "2"0"3Pb in control meals from which one dietary constituent at a time was ...
The electrochemical treatment of solutions containing C.I. Basic Yellow 2 (BY2) in aqueous solutions with carbon-PTFE (polytetrafluoroethylene) and carbon nanotube (CNT)-PTFE electrodes as cathode has been studied. The fabricated electrodes were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The amount of electrogenerated H2O2 on the surface of these electrodes was investigated, too. The results showed that the amount of H2O2 obtained with the CNT-PTFE electrode was nearly three times higher than that of carbon-PTFE electrode. The decolorization efficiency of BY2 in peroxi-coagulation process reached 62% and 96% in the first 10 min by carbon-PTFE and CNT-PTFE electrodes at 100 mA, respectively. The effect of operational parameters such as applied current, initial pH and initial dye concentration was studied in an attempt to reach higher decolorization efficiency. The degradation and mineralization of BY2 using CNT-PTFE ...
In the present study 12 diets, each one consisting of a pool of seven day diets, composed by four meals: breakfast, lunch, dinner and snack, adequate in energy and macro nutrients according to the RDA (Recommended Daily Allowance) recommendations, were elaborated and offered to a group of 12 men (19-42 years). The diets were collected by duplicate portion technique and dried by two different processes: freeze drying and 60 deg C ventilated oven drying. In the total, 24 diets were analyzed. The content of some minerals and trace elements (Ca, Fe, Mg, Mn, Na, Se and Zn) were determined by Instrumental Neutron Activation Analysis. The validation of methodology was made by analysis of the reference materials Typical Diet (NIST SRM 1548"a), Orchard Leaves (NIST SRM 1541) and Peach Leaves (NIST SRM 1547). The results observed by two different drying processes used were statistically compared by test T of Student. It was possible to conclude that the concentration means ...
Manganese is a common contaminant of mine water and other waste waters. Due to its high solubility over a wide pH range, it is notoriously difficult to remove from contaminated waters. Previous systems that effectively remove Mn from mine waters have involved oxidising the soluble Mn(II) species at an elevated pH using substrates such as limestone and dolomites. However it is currently unclear what effect the substrate type has upon abiotic Mn removal compared to biotic removal by in situ micro-organisms (biofilms). In order to investigate the relationship between substrate type, Mn precipitation and the biofilm community, net-alkaline Mn-contaminated mine water was treated in reactors containing one of the pure materials: dolomite, limestone, magnesite and quartzite. Mine water chemistry and Mn removal rates were monitored over a 3-month period in continuous-flow reactors. For all substrates except quartzite, Mn was removed from the mine water during this period, and Mn ...
It has been concluded by geologists that a significant amount of hydrogen is stored as point defects in nominally anhydrous minerals. Determination of the amount of hydrogen bound in these minerals is a step towards determining the total water content of the earth mantle as well as comprehending its internal water cycle. The possibility to measure hydrogen in thin geological samples by elastic p-p scattering has been investigated at the Lund Nuclear Microprobe. In this work the development of the experimental procedure and standardisation of data analysis is described. Special emphasis has been put into doing the data analysis as simple as possible and at the same time applicable to all sorts of thin samples, even those of unknown nature. A special annular surface barrier detector composed of two insulated detector halves, which are read out simultaneously, is used to detect the recoiled proton and the scattered proton in coincidence. ...
Microdamage naturally occurs in bone tissue as a result of cyclic loading placed on the body from normal daily activities. While it is usually repaired through the bone turnover process, accumulation of microdamage may result in reduced bone quality and increased fracture risk. It is unclear whether certain areas of bone are more susceptible to microdamage than others due to compositional differences. This study examines whether areas of microdamaged bone are chemically different than undamaged areas of bone. Bone samples (L3 vertebrae) were harvested from 15 dogs. Samples were stained with basic fuchsin, embedded in poly-methylmethacrylate, and cut into 5-(micro)m-thick sections. Fuchsin staining was used to identify regions of microdamage, and synchrotron infrared microspectroscopic imaging was used to determine the local bone composition. Results showed that microdamaged areas of bone were chemically different than the surrounding undamaged areas. Specifically, the ...
From the alkalised crude extract of Symphytum cordatum (L.) W.K. roots, pyrrolizidine alkaloids (PAs) were extracted as free tertiary bases and polar N-oxides in a merely one-step liquid-liquid partitioning (LLP) in separation funnel and subsequently pre-fractionated by preparative multiple-development (MD) thin-layer chromatography (TLC) on silica gel plates. In this way three alkaloid fractions of different polarities and retention on silica gel plates were obtained as: the most polar N-oxides of the highest retention, the tertiary bases of medium retention, and diesterified N-oxides of the lowest retention. The former fraction was reduced into free bases by sodium hydrosulfite and purified by LLP on Extrelut-NT3 cartridge. It was further analysed together with the two other fractions by high-performance liquid chromatography (HPLC)-ion-trap mass spectrometry with atmospheric pressure chemical ionization (APCI) interface ...
The oxidative dehydrogenation (ODH) of light alkanes is an alternative way for the production of olefins. A wide variety of catalytic systems has been investigated. Vanadium oxide based catalysts were described in the literature as effective catalysts for the ODH of propane. The catalytic activity and selectivity depend on the kind of support material, the kind of dopants and the formation of complex metal oxide phases. In recent papers it was claimed that both orthovanadate and/or pyrovanadate species are selective for the ODH of propane. Niobia based materials were investigated as catalysts for acidic and selective oxidation type reactions. In the ODH of propane niobia exhibited a high selectivity to propene but the conversion of propane was low. V{sub 2}O{sub 5}-Nb{sub 2}O{sub 5} catalysts proved to be catalytically active and selective and showed no formation of oxygenates. In the present study the ...
For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO{sub 2}, PrO{sub 2}), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two shapes: small cubic (oxide) and large plate-like (tetragonal) structures. The ...
For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO2, PrO2), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two shapes: small cubic (oxide) and large plate-like (tetragonal) structures. The conversion ...
Basic studies of the oxidation resistance of Fe-Cr binary and Fe-Cr-Ni ternary alloys in pure oxygen have shown that the excellent corrosion resistance of Alloy 800 is explicable in terms of the low defect concentrations and diffusion rates in the oxide forming on alloys of this composition in sufficiently oxidising environments. The performance of Alloy 800 in environments of particular importance to nuclear power generation is briefly reviewed to determine to what extent ideas derived from the basic studies of Fe-Cr-Ni ternary alloys are borne out in practice. The good corrosion resistance of Alloy 800 in steam and CO_2 and, to some extent, in molten salt environments is in agreement with the behaviour of ternary alloys in oxygen. Minor aliovalent alloying additions are only expected to have a significant effect on the oxidation resistance of Alloy 800 if they favour the formation of breakthrough duplex ...
The aim of this work is to test the catalytic oxidation of pyridine over zeolite-supported catalysts and to compare the difference in their activities for the oxidation of pyridine. The catalytic oxidation of pyridine pollutant on a series of copper-supported catalysts, inclusive of Cu/beta, Cu/ZSM-5, Cu/MCM-41 and Cu/{gamma}-Al{sub 2}O{sub 3}, in the presence of excess oxygen was studied. The activity of the copper-supported catalysts for the pyridine oxidation could be correlated with the binding energy of oxygen coordinated to metal copper, while the ability to control the yield of NO{sub x} appeared to be strongly dependent on the binding energy of NO bonded to metal copper. On these catalysts, two copper species, Cu(H{sub 2}O){sub 6}{sup 2+} ions and CuO were identified, in which Cu{sup 2+} ions had higher activity for the NO{sub x} control but poorer activity for the pyridine ...
Dominating factors in plasma nitriding and plasma condition that makes nitriding possible in plasma nitriding process of metals having hard oxide film were studied. In case of stainless steel, oxide film sputtering was easier comparing to nitriding layer. Three phenomena such as sputtering of oxide layer, formation of nitriding layer and sputtering of nitriding layer occurred simultaneously. Nitriding was achieved when the formation of nitriding layer reached the peak comparing to the removal of nitriding layer after the removal of oxide layer. Situations of metallic surface of stainless steel in surface nitriding were divided into four categories and they were, situation where oxide layer remained as it is, situation where nitriding layer was formed although oxide layer remained in some part, situation where only nitriding layer was formed and situation where ...
Results on the oxidative dehydrogenation of ethane on rare-earth oxide (REO) based catalysts (Na-P-Sm-O, Sm-Sr(Ca)-O, La-Sr-O and Nd-Sr-O) are described. Oxygen adsorption was found to be a key factor which determines the activity of this type of catalysts. Continuous flow experiments in the presence of catalysts which reveal strong oxygen adsorption showed that the reaction mixture is ignited resulting in an enhanced heat generation at the reactor inlet. The heat produced by the oxidative reactions was sufficient under the conditions chosen for the endothermic thermal pyrolysis which takes place preferentially in the gas phase. Ignition of the reaction mixture is an important catalyst function. Contrary to non-catalytic oxidative dehydrogenation, reaction temperatures above 700 C could be achieved without significant external heat input. Ethylene yields of up to 34-45% (S=66-73%) were obtained on ...
A laboratory-scale well-mixed thermostatic reactor with continuously blasting air was used to investigate the oxidation inhibition of sulfite in dual alkali flue gas desulfurization (FGD) system. The effects of operating parameters such as pH value and catalyst concentration on the oxidation were studied. Sodium thiosulfate was used in the system, and was found that it significantly inhabited the sulfite oxidation. In the absence of catalyst, sodium thiosulfate at 12.67 mmol/L had an inhibition efficiency of approximately 98%. While in the presence of catalyst, sodium thiosulfate at 26.72 mmol/L had an inhibition efficiency less than 85.0%. The oxidation reaction order of sulfite in the sodium thiosulfate was determined to be -1.90 and -0.55 in the absence and presence of the catalyst, respectively. Apparent activation energy of oxidation inhibition was calculated to be 53.9 kJ/mol. ...
Boron is implanted in crystalline silicon through oxide layers with different thicknesses. The implantation is carried out at various doses and energies of interest in ultra large scale integration (ULSI) application. Rapid thermal annealings (RTA) are used to obtain shallow junctions and electrical activation of the B atoms. However, transient enhanced diffusion induced by implantation damage can be observed. The boron concentration profiles before and after annealing are obtained with secondary ion mass spectrometry (SIMS). It is found that the diffusion transient in the tail region of the boron profile increases with decreasing oxide thickness. Even more, if the implantation damage concerns mostly the oxide, i.e. when the concentration peak is located in this oxide, the oxygen knocked into the silicon substrate could play this way an important role in restricting the boron diffusion, which is good to ...
Boron is implanted in crystalline silicon through oxide layers with different thicknesses. The implantation is carried out at various doses and energies of interest in ultra large scale integration (ULSI) application. Rapid thermal annealings (RTA) are used to obtain shallow junctions and electrical activation of the B atoms. However, transient enhanced diffusion induced by implantation damage can be observed. The boron concentration profiles before and after annealing are obtained with secondary ion mass spectrometry (SIMS). It is found that the diffusion transient in the tail region of the boron profile increases with decreasing oxide thickness. Even more, if the implantation damage concerns mostly the oxide, i.e. when the concentration peak is located in this oxide, the oxygen knocked into the silicon substrate could play this way an important role in restricting the boron diffusion, which is good to ...
In this work we present an ultra-low temperature method for the oxidation of an amorphous silicon-carbide-nitride (SiCN) material. The SiCN is deposited on silicon substrates by plasma enhanced chemical vapor deposition using CH{sub 4}, SiH{sub 4}, and N{sub 2} chemistry. The physical and chemical properties are characterized for the as-deposited SiCN and post-oxidized films are discussed. The SiCN film is exposed to oxygen plasma, where it undergoes a chemical transformation into a binary SiO{sub 2} material system. A 1.7 nm/min oxidation rate is typical for this process and compares favorably to oxidation methods utilizing much higher temperatures. The substrate temperature remains extremely low throughout the oxidation process, T{sub s} < 200 deg. C. Changes in film stress, optical constants, film thickness, surface roughness, and film density are measured. Chemical ...
'The interactions of carbon tetrachloride with strongly basic oxides and hydroxides have been studied by several techniques in order to understand the surface reactions and the subsequent bulk reactions that result in the destruction of the chlorinated hydrocarbon. Emphasis has been placed on understanding the surface phases, as well as the bulk phases, that are present during these transformations. As a result of the study with barium oxide, a reaction cycle has been demonstrated that may have practical significance in the removal of chlorinated hydrocarbons.'
In most industrial processes operating at elevated temperatures, protective oxide layers perform a vital duty in protecting the underlying metallic alloys from process gases. Coal-fired combined cycle power generation systems present a number of process conditions in which the properties of the protective oxide layers are particularly important. This paper discusses two of these particular conditions: (1) `erosion/corrosion` of in-bed heat exchanger tubing and (2) thermal cycling of hot gas path components. For both these situations, the desirable properties of protective scales are outlined. The behaviour of scales in practice are highlighted. 33 refs., 6 figs., 2 tabs.
Chlorophyll a, chlorophyll b, and bacteriochlorophyll a in aqueous micellar solutions of Trition X 100 (2%) are readily oxidized by pulse-radiolytically generated N_3., Br_2"-., and (SCN)_2"-. radicals at nearly diffusion-controlled rates. The kinetic study suggests that pigment molecules occupy multiple sites in the micelle. Pheophytin a is only oxidized by N_3. and Br_2"-. radicals. The absolute spectra and the molar extinction coefficients of chlorophyll a, bacteriochlorophyll a, chlorophyll b, and pheophytin a cations have been determined. The chlorophyll a cation has been observed in the presence of pigment aggregates.
Applying the thermochemical selectivity criterion of Hadnett et al. It is shown that the selectivity of the furan formation is not limited by a too low strength of the C-H bonds in furan when compared with the C-H bond dissociation energy in the educt molecule butadiene. In the oxidation of butadiene on a CsH{sub 2}PMo{sub 12}O{sub 40} catalyst a maximum yield of 22 mol% furan has been obtained. To improve this comparatively low furan yield oxidation activity of the catalyst must be lowered to prevent the consecutive reaction to maleic anhydride. (orig.)
A nitrogen oxides decreasing combustion method comprising: mixing a fuel and air with each other; bringing the mixture obtained into contact with a packed catalyst; and adding a fresh supply of the fuel to the stream obtained to form a mixed gas and causing the mixed gas to undergo non-catalytic thermal combustion, characterized in that only a catalytic reaction or combustion occurs at the packed catalyst; the temperature of the packed catalyst is kept lower than the ignition temperature of the mixture; the adiabatic flame temperature which is reached by the non-catalytic thermal combustion of the mixed gas is lower than the temperature at which the nitrogen oxides occur. 39 figs.
This patent describes a nitrogen oxides decreasing combustion method which comprises: a first step of mixing a fuel and air with each other; a second step of bringing the mixture obtained in the first step into contact with a packed catalyst such that only catalytic combustion occurs; and a third step of adding a fresh supply of the fuel to a stream obtained from the second step to form a mixed gas and causing the mixed gas to undergo non-catalytic thermal combustion. The temperature of the packed catalyst is lower than the ignition temperature of the mixture and the adiabatic flame temperature of the mixed gas is lower than a temperature at which the nitrogen oxides occur.
Several possibilities of the use of molecular models in quantum-chemical investigations of the structure of defect centers on the surfaces of oxides on nontransition elements have been illustrated. There has been a special discussion of the assumption of the local nature of the chemical interactions in these systems, which underlies such an approach, and of the consequent laws governing the formation of their lattices in the example cases of zeolites, kaolinites, and comparable boron- and aluminum-containing oxides. A quantum-chemical interpretation of the body of experimental data from investigations of the dehydroxylation of H forms of zeolites has been given. The structure of the Lewis acid centers formed as a result, and their chemisorption properties, have been discussed.
Cr_2O_3 scales are found to form on Alloy 800 and a similar pure ternary alloy in air, and 1 and 50 atm. helium containing oxidizing impurities typical of those in an SGHTR. The strong temperature dependence and neglibible helium overpressure dependence indicate that gas transport through the scales is not rate controlling. Surface oxidation rates are therefore controlled by solid state diffusion and the low oxygen partial pressure dependence of the oxidation rate in Alloy 800 is ascribed to the presence of extrinsic defects in the Cr_3O_3 (due to doping by alloying elements) or to the presence of short circuit diffusion paths. (Auth.).
We report on the single-particle properties of lanthanide-ion doped oxide nanoparticles. We have demonstrated that their size can be accurately determined from their luminosity. The optically determined size distribution is in very good agreement with the distribution obtained from transmission electron microscopy (TEM). We also showed that the photobleaching of these nanoparticles is related to a reduction process and that we can use it to sense in a concentration-dependent manner the presence of an oxidant like H2O2. Finally, we propose a way to perform nanoparticle-protein coupling and to determine the protein-nanoparticle ratio at the single-particle level.
This work deals with kinetic description of carbothermic reduction of iron oxides using microwaves as power source. Previous researches show that it is possible to conduct this kind of process successfully, but real kinetic comparisons between conventional and microwaves procedure have been presented partially. The aim of this work is to describe reduction kinetics, taking into account how the iron oxide is reduced by microwaves compared with conventional energy supply. In this study the authors used iron ore in pellet shape and dust. They found that both, pellet and dust reduction stops when it reaches approximately 40%, even at whole power.
Lanthanide-ion doped oxide nanoparticles were functionalized for use as fluorescent biological labels. These nanoparticles are synthesized directly in water which facilitates their functionalization, and are very photostable without emission intermittency. Nanoparticles functionalized with guanidinium groups act as artificial toxins and specifically target sodium channels. They are individually detectable in cardiac myocytes, revealing a heterogeneous distribution of sodium channels. Functionalized oxide nanoparticles appear as a novel tool particularly well adapted to long-term single-molecule tracking.
Separation of lithium isotopes was investigated by chemical ion exchange with a hydrous manganese(IV) oxide ion exchanger using an elution chromatography. The capacity of manganese(IV) oxide ion exchanger was 0.5 meq/g. The heavier lithium isotope was enriched in the solution phase, while the lighter isotope was enriched in the ion exchanger phase. The separation factor was determined according to the method of Glueckauf from the elution curve and isotopic assays. The separation factor of {sup 6}Li{sup +} -{sup 7}Li{sup +} isotope pair fractionation was 1.018.
Uranium has varying degrees of oxidation (+4 and +6) and is responsive to changes in the redox potential of the environment. It is deposited at the reduction barrier with the participation of biota and at the sorption barrier under oxidative conditions. Iron (hydr)oxides are the strongest sorbents of uranium. Uranium, being an element of medium biological absorption, can accumulate (relative to thorium) in the humus horizons of some soils. The high content of uranium in uncontaminated soils is most frequently inherited from the parent rocks in the regions of positive U anomalies: in the soils developed on oil shales and in the marginal zone of bogs at the reduction barrier. The development of nuclear and coal-fired power engineering resulted in the environmental contamination with uranium....
One of the main problems related to optical thin film materials used in high power laser environments is the catastrophic damage caused to them due to laser irradiation. While the influence of ion bombardment on the optical properties of oxide thin films is now a well understood subject, the morphology and crystalline behaviour of these films under ion incidence is not so well studied. Hence, it is of great importance to investigate the effects of ion bombardment during growth on the microstructure and crystalline behaviour of oxide materials.
The article focusses on operational experience gained with the following items: scrubbing system with oxidation, regenerative gas preheater, blower/fan, aerosol filter, and product processing. (orig./PW).
A study was made of the uncoupling action of polychlorinated biphenyls (Kanechlor-400) on oxidative phosphorylation in rat liver mitochondria. Kanechlor-400 (KC-400) at 20 ..mu..g/ml stimulated state 4 respiration of rat liver mitochondria more than 4-fold with ..cap alpha..-ketoglutarate/malate as a substrate, and released the oligomycin-inhibited state 3 respiration. KC-400 also dissipated the membrane potential across the mitochondrial membranes; thus, it acts as an uncoupler of oxidative phosphorylation in rat liver mitochondria. KC-400 altered the permeability properties of mitochondrial membranes as evidenced by the release of endogenous K/sup +/ and the oxidation of exogenously supplied NADH. It is concluded that KC-400 produces a nonspecific increase in mitochondrial ion permeability, thereby dissipating membrane potential, which leads to the uncoupling.
Metallic Zn films were deposited on glass substrates by electron-beam evaporation. ZnO films were synthesized by thermal oxidation of Zn metallic films in air. At the annealing temperature of 550 ?C, ZnO nanowires appeared on the surface, which mainly result from the decrease of oxidation rate. A ZnO ultraviolet photodetector was fabricated based on a metal-semiconductor-metal planar structure. The detector showed a large UV photoresponse with an increase of two orders of magnitude. It is concluded that promising UV detectors can be obtained on ZnO films by thermal oxidation of Zn metallic films. The ways of performing spectral response measurements for polycrystalline ZnO films are also discussed.
The oxidation of n-butylbenzene was studied in a jet-stirred reactor (JSR) at 10atm in dilute conditions providing new experimental results over the low- and high-temperature range 550-1180K, and variable equivalence ratio (0.25ϕ1.5). They consisted of concentration profiles of the reactants, stable intermediates and final products, measured as a function of temperature, at a constant residence time of 1s, by sonic probe sampling followed by on-line GC-MS and off-line GC-TCD-FID and GC-MS analyses. The oxidation of n-butylbenzene in these conditions was modeled using a detailed chemical kinetic reaction mechanism (404 species and 2210 reactions, most of them reversible) deriving from a previous scheme proposed for the ignition, oxidation, and combustion of simple aromatics (benzene,...
A thermodynamic analysis of the behaviour of Alloy 800 in helium based atmospheres relevant to the High Temperature Gas Cooled Reactor indicates that, depending upon the precise gas composition, oxidation and carburisation, or carburisation alone may be expected. The prime influence appears to be the moisture level. The morphology and structure of the reaction products are discussed. It is shown that the 'reactive' elements chromium, manganese, titanium and silicon are concentrated in the oxide scale which is normally duplex in structure. Aluminium oxide is formed at grain boundaries and in an internal oxidation zone together with titanium and sometimes silicon. In carburising conditions, mixed titanium-chromium carbides are formed. When this occurs, intergranular penetration is maximised. Weight gain data are assessed and briefly described and a tentative model for the mechanism of corrosion of Alloy ...
The catalytic oxygen transfer properties of vanadium containing zeolites and vanadium based sol-gel catalysts with hydrogen peroxides are well known. The severe problem of vanadium leaching caused by the presence of the by-product water has been addressed. To avoid any interference with homogeneously catalyzed reactions, our study focusses on selective oxidations in a moisture-free medium with tert.-butylhydroperoxide. We have investigated the catalytic properties of amorphous microporous materials based on SiO{sub 2}, TiO{sub 2}, ZrO{sub 2} and Al{sub 2}O{sub 3} as matrix material and studied the effects of surface polarity on the oxidation of 1-octene and cyclohexane. (orig.)
Senescence is regarded as a physiological response of cells to stress, including telomere dysfunction, aberrant oncogenic activation, DNA damage, and oxidative stress. This stress response has an antagonistically...Full Text Available
Obesity is characterized by the abnormal or excessive deposition of fat in the adipose tissue. Its consequences go far beyond adverse metabolic effects on health, causing an increase in oxidative stress,...Full Text Available
familiarity fire triangle (i.e., fuel, oxidant, and ignition source) are excluded. It Is obvious that for the baseline safety goal for spacecraft this ...
All of the direct reaction schemes described and the corresponding process schemes are still in an exploratory state. Ethylene by oxidative coupling of methane could become competitive if process schemes are developed with significantly less expenditures for separation of the product from unconverted feed. No encouragement for formaldehyde from methane can be presently derived from the existing knowledge. Liquid-phase oxidation of methane to methanol appears to be attractive but no final judgement is possible at present. Oxidative dehydrogenation of ethylene and propane look promising although further catalyst improvement is required. Acetic acid from ethane and acrylonitrile from propane have a certain potential as an alternative to present technology. The outlook for acrolein and acrylic acid from propane is less favourable; new concepts for catalyst design are necessary. (orig.)
Pulse reactor experiments were conducted on the reactions of unlabeled or deuterium- or oxygen-18-labeled allyl alcohols over molybdenum trioxide and various bismuth molybdates in the absence or presence of oxygen and ammonia. The allyl alcohol apparently adsorbed on oxidation sites to form acrolein via allyl molybdates, and on Broensted acid sites to form diallyl ether via an allyl carbonium ion. The bismuth enhanced ..cap alpha..-hydrogen abstraction, which was the rate-determining step in the oxidation. The product distributions provided evidence that the selective oxidation of propylene to acrolein proceeds via a m-allyl molybdate which collapses to an O o-allyl molybdate prior to the second hydrogen abstraction, and that the analogous N o-complex in ammoxidation undergoes two hydrogen abstractions to form acrylonitrile. Detailed reaction schemes are developed.