International Nuclear Information System (INIS)

A new dedicated UHV STM for investigations at T#<=#5 K is presented. To achieve such low temperatures and to ensure a high thermal stability, the low-temperature (LT) STM described here has a concentric system of bath cryostats. There are openings for tip and sample exchange at low T, and windows with an infrared radiation shield for optical access, which can both be closed by a door mechanism for LT-STM measurements. Efficient vibration isolation is realized by using spring suspension with eddy current damping. With the 3-d coarse positioning unit any region of interest within 5 mm by 5 mm on the sample is accessible even at 5 K. For short turn-around cycles the sample and tip can both be exchanged at low temperatures. Atomically resolved images of Au(111) at 5 K in UHV demonstrate the excellent performance of this LT STM. As a typical application example the appearance of a charge-density wave on NbSe_2, which occurs ...

Energy Technology Data Exchange (ETDEWEB)

Requirements are provided for NSLS beam line front ends and vacuum interlocks. Guidelines are provided for UHV beam line vacuum systems, including materials, vacuum hardware (pumps, valves, and flanges), acoustic delay lines and beam line fast valves, instrumentation, fabrication and testing, and the NSLS cleaning facility. Also discussed are the design review for experimenters' equipment that would be connected to the NSLS and acceptance tests for any beam line to be connected with the ring vacuum. Also appended are a description of the acoustic delay line as well as the NSLS vacuum standards and NSLS procedures. (LEW)

International Nuclear Information System (INIS)

Focussed ion beam (FIB) technology has the advantage of being a maskless process compatible with UHV processing. This makes it attractive for use in in situ processing and has been applied to the fabrication of various mesoscopic structures. The present paper reviews these results whilst putting emphasis on in situ processing by a combined FIB and molecular beam epitaxy system. The typical performance of present FIB systems is also presented. In order to utilize the potential advantages of FIB processing, reduction of damage and improvement of throughput are important, and much effort has been devoted to developing processing techniques which require a reduced dose. The importance of low-energy FIB is discussed. (author).

Wastenet

... Advances in Complex Systems ( ACS) 413 (413) 2001-2011 Springer Advances in Data Analysis and Classification 59 (59) 2008-2011 Advances in Management Advances In Management ...

Energy Technology Data Exchange (ETDEWEB)

Since 1985 the operating sections of the 1200 kV AC Ekibastuz-Urals transmission system were used for a variety of field studies on a wide range of technological problems associated to high voltage transmission lines. The tests performed confirmed correctness of the main engineering and design decision made at development stage and demonstrated that such transmission lines are reliable and efficient. 3 figs.

Energy Technology Data Exchange (ETDEWEB)

The HVDC link across the English Channel, which was brought into service in 1986, has several innovative features. Techniques used in its construction together with recent developments have consolidated the viability of HVDC links for a variety of applications. Outlines the main features of the scheme, including the benefits of interconnecting the British and French 400 kV AC power systems; integration of the UK converter system to the 400 kV AC grid; the DC submarine cables; convertor equipment (particularly the UK installation); and future HVDC developments. 6 refs.

Energy Technology Data Exchange (ETDEWEB)

Increasing environmental awareness and new legislation in Europe and, in particular, America have accelerated the development of marketable electric cars which satisfy customer demands in terms of performance, range capability, safety and comfort. Tomorrow's electric cars will therefore require powerful heating and cooling systems for the passenger compartment which meet the conditions specific to this particular mode of transport and which do not overly affect the range capability of such vehicles. At Behr GmbH suitable system concepts were developed at a very early stage which were based on a high proportion of recirculated air, the use of the A/C unit as a heat pump, and heat recovery. This paper will examine two typical A/C systems which combine good heating and cooling characteristics with the low electric power requirement of only 1,5-2 kW. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Conventional methods for calculating electricity losses in pipe-type cable systems rely heavily on data measured in lower-voltage systems in the 1950s. With the new technique developed in this study, engineers can compute power losses more precisely for cables of various configurations and voltage ratings.

Energy Technology Data Exchange (ETDEWEB)

The use of the focused ion beam (FIB) systems has increased to a high level in recent years. The imaging, milling, and deposition capabilities of the FIB make it the ideal instrument for e.g., site-specific failure analysis, specimen preparation and nano-machining. Ion channelling contrast allows for selective imaging of polycrystalline and polyphase microstructures. In addition, the FIB and CrossBeam registered instruments are unique stand-alone analytical tools. Their vast capabilities have enabled numerous applications into the semiconductor and materials sciences applications. These integrated CrossBeam registered Tools enable the observation and direct control of the FIB operation in real time. In addition to the improved accuracy and resolution the electron beam adds analytical capabilities as STEM, EDS and EBSP to the instruments. To ensure a safe and reliable operation of the instrument, a dedicated vacuum system is needed. This type of ...

Energy Technology Data Exchange (ETDEWEB)

This paper reports the result obtained during fiscal 1994 on a demonstration research on photovoltaic power generating systems. Solar cells with an output of 750 kW, storage battery facilities with an output of 3,058 kWh, three DC-AC converters with a rating of 250 kW, and a diesel generator with an output of 300 kW having been installed up to the previous fiscal year were combined to perform comprehensive adjustments and tests such as battery charge/discharge tests and AC parallel operation tests. The battery charge/discharge tests revealed that the 10 hour rate discharge capacity meets the specifications, and the batteries are free of deterioration after a demonstration operation of about 4.5 months. Difference between the power generation record and the planned value is thought due to the following reasons: the array output data in a power line connected system come about 90% of the simulation result ...

Energy Technology Data Exchange (ETDEWEB)

The a.c. susceptibility and high field magnetization of TbRh{sub 2-x}Pd{sub x}Si{sub 2} and TbRu{sub 2-x}Pd{sub x}Si{sub 2} compounds were investigated up to 140 kOe. The (T, x) magnetic phase diagrams were determined. For both systems, an increase in the Pd content causes a decrease in the Neel temperature and changes the magnetization curves. (orig.)

Wastenet

on practical projects such as woodland management, limestone grassland management, cattle management, conflict management and education. ...Cathy Heaton Telephone 01772 892400 Email cenquiries@uclan.ac.uk www.uclan.ac.uk/schoolbne

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy`s Pittsburgh Energy Technology Center (PETC) is actively pursuing the development and testing of coal-fired combustion systems for residential, commercial, and industrial market sectors. In response, MTCI initiated the development of a new combustor technology based on the principle of pulse combustion under the sponsorship of PETC (Contract No. AC22-83PC60419). The initial pulse combustor development program was conducted in three phases (MTCI, Development of a Pulsed Coal Combustor Fired with CWM, Phase III Final Report, DOE Contract No. AC22-83PC60419, November 1986). Phase I included a review of the prior art in the area of pulse combustion and the development of pulse combustor design concepts. It led to the conclusion that pulse combustors offer technical and base-of-operation advantages over conventional burners and also indicated favorable economics for replacement of oil- and gas-fired ...

British Library Electronic Table of Contents (United Kingdom)

Electrostatic torsional micro-mirrors have wide spread use in different industries for diverse purposes. This paper investigates the development of superharmonics and chaotic responses in electrostatic torsional micro-mirrors near the pull-in condition. Appearance of nonlinear phenomena is investigated in models accounting for and disregarding the coupling of torsional and flexural deflections. Analysis of the system response to step and harmonic excitation reveals the appearance of DC and AC symmetry breaking. Increasing the amplitude of harmonic excitation, the response in the form of distinct superharmonics changes to a broad band response, where there is loss of periodicity and the response becomes chaotic. Accounting for flexural deflections in coupled model reduces the voltage thresh...

Energy Technology Data Exchange (ETDEWEB)

Using electromatic field theory, a new method is developed for calculating alternating current in power cables installed in pipes of carbon steel (magnetic pipes). The technique for evaluating these losses is based on the method of images which replaces complicated distribution of currents in the system with a sequence of thin conductors. The method not only gives a mathematical framework for the solution of alternating current losses, but it also gives the underlying physical picture of effects contributing to these losses. Skin effect, proximity effect and losses due to the pipe are calculated separately. For the first time, the increase of losses in the conductors, when the cables are placed in a magetic pipe, are analyzed mathematically. Good agreement is obtained between the result of calculations and the experimentally determined ac-dc resistance ratios for pipe-type cables with concentric stranded copper conductors and also for cables ...

Norwegian Open Research Archives (NORA)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

For the protection of buried steel pipeline, it is common practice to coat the pipelines with highly insulating coating and apply a cathodic current to insulate the pipe from the aggressive environment. Cathodic current protects holidays or damaged area of coating which required less current than would be needed for an uncoated pipe, but because of the cathodic reactions evolution will be taken H{sub 2} and OH{sup -} on holidays which exposed metal to the environment place. This effect is to cause loss bond of coating around the holidays called cathodic dis-bonding. In this paper we measured cathodic dis-bonding of three types of coatings at - 1.5 V(Cu/CuSO{sub 4}) according to ASTM G8. We studied on cathodic dis-bonding resistance of petroleum-base, coal tar-base and polyethylene plastic tape coatings. After 30 days immersion in electrolyte it was found that the cathodic disbanding resistance of polyethylene plastic tape coating is lower than others and high cathodic dis-bonding ...

Energy Technology Data Exchange (ETDEWEB)

The motivation of this work is to develop high reflectance normal-incidence multilayer mirrors in the 8-12 nm wavelength region for applications in astronomy and extreme ultraviolet lithography. To achieve this goal, Mo/Sr and Mo/Y multilayers were studied. These multilayers were deposited with a UHV magnetron sputtering system and their reflectances were measured with synchrotron radiation. High normal-incidence reflectances of 23% at 8.8 nm, 40.8% at 9.4 nm, and 48.3% at 10.5 nm were achieved. However, the reflectance of Mo/Sr multilayers decreased rapidly after exposure to air. Attempts to use thin layers of carbon to passivate the surface of Mo/Sr multilayers were unsuccessful. Experimental results on the refractive index {tilde n} = 1-{delta} + i{beta} of yttrium and molybdenum in the 50-1300 eV energy region are reported in this work. This is the first time ever that values on the refractive index of yttrium are measured in this energy ...

Energy Technology Data Exchange (ETDEWEB)

A new method of plasma treatment for powder particles was investigated. A glass bottle horizontally held on a rotating system was used for the treatment. The outside of the bottle was covered by the grounded metal net, and the rod electrode was provided at the center of the bottle, which was connected to an ac high voltage source. Powder particles were placed in the bottle with stainless steel beads of large diameter and the plasma was generated between two electrodes and while the bottle was rotating. Using this system, powder particles were uniformly plasma-treated without coagulation. After 40 seconds treatment with plasma of 0.55 W in Ar gas, the charge to mass ratio for polyethylene powder particles having 160 {mu}m mean diameter generated by stainless before treatment. (author)

Energy Technology Data Exchange (ETDEWEB)

A general calculation method for the analysis of transmission capability of a long-distance single-core ac submarine cable system is presented. The method is based on modal transformation of voltages and currents in multiconductor cable systems. Using this method, numerical calculations on 500 kV submarine cable systems have been performed with particular reference to the effect of the distance between bonds connecting metallic sheath, outer conductor and armor on the transmission capacity of the system. It was clarified that the transmission capacity of the system increased with decreasing bond intervals. Examination of the current distributions between various conductors along the length showed that this increase of transmission capacity was mainly due to the dispersion of the charging current into the metallic sheath, outer conductor and armoring at the ...

Energy Technology Data Exchange (ETDEWEB)

This project is a follow-up of the first development of a 500 kV HVDC airblast circuit breaker (EPRI project 1507-3). The objective was to increase the current interrupting capability from 2200 A to 4000 A and shorten its fault clearing time. A high current 500 kV HVDC circuit breaker has been built using the passive commutation circuit. The breaker is modular in construction and can be designed for a wide variety of system conditions. More than 400 current interruptions were carried out successfully. Tests have shown that this circuit breaker is capable of interrupting more than 4000 A dc. Practical breakers with current interrupting capability of even 5500 A dc could be built. The circuit breaker operation and the fault-clearing process can be materially speeded up if the trip signal is given as soon as the fault is detected and without waiting for the current levels to come down in response to converter control action. The new dc breakers are shown to be capable ...

British Library Electronic Table of Contents (United Kingdom)

Individuals who use augmentative and alternative communication (AAC) depend on technology to meet their daily needs and form relationships. Speech generating devices (SGDs) are integral components of communication systems. Reliability of SGDs is critical for effective use in everyday life. This study examined the reliability of new SGDs and found that mean time to first failure was 42.7 (SD = 41.2) weeks and at least 40% required repairs within the first year of use. The components that most frequently broke down were touch screens, wiring, main boards, batteries, memory cards, and AC adaptors. The costs of repairing SGDs were analyzed. The clinical implications of device breakdown are identified for key stakeholders, including clients, families, service providers, funding agencies, and ma...

International Nuclear Information System (INIS)

Ferrite of system, namely Ni_1_-_xZn_xFe_2O_4 with x = (0.0, 0.2, 0.4, 0.6, 0.8, 1.0), have been prepared by solid state reaction to investigate the effect of gamma rays irradiations using Co"6"0 source on the cation distribution, structural and magnetic properties. The unirradiated and irradiated samples were then subjected to characterization techniques such as X-ray diffraction, magnetization and AC susceptibility. The results of these characterizations are found to be different for irradiated from that of the pristine sample. The modifications in respect of irradiated samples are explained in terms of the ion-induced disorder. The important result of #gamma#-irradiation on the cation distribution, structural and magnetic properties is the change of ratio Fe"2"+/Fe"3"+. Possible reasons on the results are proposed.

British Library Electronic Table of Contents (United Kingdom)

This paper presents the results of the degree of irreversible changes of dielectric properties of vacuum circuit breakers with CuCr and CuBi contacts before and after short-circuit breaking operations. Tests of dielectric properties were performed on four different types of switching vacuum chamber with RMF electrodes in the form of a spiral disk with slots. The paper describes the configuration of measuring system for determining the dielectric properties of circuit breakers with DC, AC and pulse voltage. It also describes the measuring procedure. The results were analyzed and the experimentally obtained random variable breakdown voltage is found to belong to Weibull distribution in all cases. Based on these results it was found that for the vacuum circuit breakers with CuCr contacts and ...

International Nuclear Information System (INIS)

Manitoba Hydro's Ice Storm Management Program to reduce ice damage to overhead power lines in the voltage range of 8 kV to 115 kV is described. Overhead power lines are de-iced either by AC ice melting, which involves placing a three-phase short at a calculated point, or ice rolling, which is a process of mechanically stripping ice from conductors. Direct current heating and underground distribution systems are also accepted prevention measures. Advantages and disadvantages of each of these methods of de-icing are reviewed. Material for this paper has been extracted from a workshop manual prepared for the 1993 and 1998 Ice Storm Management workshops organized by Manitoba Hydro through the Canadian Electrical Association. 1 ref.

Energy Technology Data Exchange (ETDEWEB)

A series of line fault tests have been conducted at completion of Stage I of the Hokkaido-Honshu HVDC Link of Electric Power Development Co., Ltd., prior to its commercial operation, in order to study transient overvoltages and overcurrents and to confirm safety operation of system protecting devices in case of DC transmission line faults. The Hokkaido-Honshu HVDC Link is a metallic return HVDC overhead line and cable transmission system, currently being a monopolar system. For this, measurements were conducted this time on reverse polarity overvoltages occurring on main line cable, return line overvoltages, fault arc dynamic characteristics, and DC bypass current through the AC system. The results obtained were then compared with the analysis results by the HVDC surge similator or digital simulation conducted for system design prior to the field tests. As a ...

Energy Technology Data Exchange (ETDEWEB)

The dry desulfurization, denitrification and air toxics removal process using activated coke (AC) has been commercially adapted for flue gas clean up of a power plant, an oil refinery plant, an iron ore sintering plant, and a refuse incinerator. This process can achieve 100% removal of SO{sub x}, over 80% removal of NO{sub x} and effective removal of air toxics such as Hg, HCL, dioxines, etc., by contacting flue gas with AC and injecting NH{sub 3} for DeNO{sub x} at temperature range of about 100-200{degrees}C. For flue gas treatment, AC has several functions, which basically depends on the chemical surface group on AC inner surface. As adsorbent, AC can adsorb SO{sub x} at the relatively basic oxygen group site, where the adsorbed SO{sub x} is stored as sulfuric acid into micropore structure of AC. As catalyst, AC can decompose NO{sub x} ...

Energy Technology Data Exchange (ETDEWEB)

The current--density profile of a focused ion beam (FIB) has a central peak accompanied by broader ``wings`` that, while unimportant in lithographic applications, can lead to unwanted effects during an implantation operation. The origin of the wings, and hence the best way to minimize them, is not clear and needs further study. We have measured the line profiles of several of the ions available in our FIB machine as a function of a number of variables, under ultrahigh vacuum (UHV) conditions. No effects are observed from changes in emission current or deliberate defocusing of the objective lens. There are some changes with beam aperture and/or current, but the biggest differences seem to be associated with a change of source type and hence, possibly, with a change in the source/extractor configuration or in the alloy and the emission process. The wing amplitudes are appreciably lower than many previously observed, and their profiles, at least for the lighter ions ...

International Nuclear Information System (INIS)

(Dec 1973). United Kingdom Stevenson, AC Medical Research Council, Oxford

International Nuclear Information System (INIS)

A study of the thin gold film growth, during the deposition on glass substrate under UHV conditions at low temperatures, is presented. The complementary methods, the atomic force microscopy and grazing incidence x-ray reflectometry, are used for the research. It is shown that due to variation of the time of deposition from 2 to 50 min different kinds of thin Au films nanostructures are obtained: from discontinuous films consisting of isolated islands, via formation of the chains of islands, up to continuous films. (author)

Energy Technology Data Exchange (ETDEWEB)

The paper describes a concept of extracting fusion power from D-{sup 3}He fueled IEC (Inertia Electrostatic Configuration) devices. The fusion system consists of a series of fusion modules and direct energy converters at an end or at both ends. This system of multiple units is linear and is connected by a magnetic field. A pair of coils anti-parallel to the magnetic field yields a field-null domain at the center of each unit as required for IEC operation. A stabilizing coil installed between the coil pairs eliminates the strong attractive force between the anti-parallel coils. Accessible regions for charged particle trajectories are essentially isolated from the coil structure. Thus, charged particles are directed along magnetic field lines to the direct energy converter without appreciable losses. A direct energy converter unit designed to be compatible to this unique system is also described. It basically consists of a ...

Energy Technology Data Exchange (ETDEWEB)

The concept of a direct energy recovery system that applies a varying magnetic field is proposed for a negative-ion-based neutral beam injection system (NNB) to heat a plasma and/or drive a plasma current in a fusion reactor. The output beam energy and power of such an NNB will be {approximately}1 MeV and {approximately}1- MW/beam-line, respectively, and nearly the same amounts of positive- and negative-ion beams remain unneutralized in an NNB by using a gas-neutralizing cell. Therefore, the output of a beam direct convertor in an NNB is a bipolar direct current (dc) electric power with close to {plus_minus} 1 MV and several amperes if a conventional electrostatic or magnetostatic field is applied for ion beam separation. However, such high-voltage dc power is difficult to handle at the point of the regeneration of the power back to a commercial electric line because a very high voltage inverter tough enough to withstand occasional sparkdowns ...

International Nuclear Information System (INIS)

Topics related to aerospace power are discussed, taking into account trends and issues of military space power systems technology, space station power system advanced development, the application and use of nuclear power for future spacecraft, the current status of advanced solar array technology development, the application of a parabolic trough concentrator to space station power needs, life test results of the Intelsat-V nickel-cadmium battery, and metal hydride hydrogen storage in nickel hydrogen batteries. Other subjects explored are concerned with alternative fuels, biomass energy, biomedical power, coal gasification, electric power cycles, and electric propulsion. Attention is given to an advanced terrestrial vehicle electric propulsion systems assessment, fuel cells as electric propulsion power plants, a sinewave synthesis for high efficiency dc-ac conversion, steam desulfurization of coal, ...

Energy Technology Data Exchange (ETDEWEB)

The increasing complexity of the real-time data acquisition and processing systems (TDAQ: the so called Trigger and Data AcQuisition systems) in high energy physics calls for an appropriate evolution of development tools. This work is about the interplay between in principle specifications of TDAQ systems and their actual design and realization on a concrete hardware and software platform. The basis of our work is to define a methodology for the development of TDAQ systems that meets the specific demands for the development of such systems. The result is the detailed specification of a 'methodological framework' based on the Unified Modeling Language (UML) and designed to manage a development process. The use of this UML-based methodological framework progressively leads to the setting up of a 'home-made' framework, i.e. a ...

Energy Technology Data Exchange (ETDEWEB)

Presently, high wind potentials in remote areas may not be utilized for electricity production due to limited grid transmission capacity and/or difficulties in matching the electricity production with the demand. The overall project objective is to help overcome these bottlenecks, i.e. to identify and analyze methods and technologies for making it viable to utilize more of the wind potential in remote areas. The suggestion is to develop a power control concept for wind turbines which will even out the power fluctuations and make it possible to increase the wind energy penetration. The main options are to combine wind power with a pumped hydro power storage or with an AC/DC converter and battery storage. The AC/DC converter can either be an `add-on` type or it can be designed as an integrated part of a variable speed wind turbine. The idea is that combining wind power with the power control concept will make wind power more firm and possible to ...

Energy Technology Data Exchange (ETDEWEB)

This paper described the application of an AC surface probe, similar to presently used eddy current probes, to the measurement of DC transport critical currents and critical state dissipation in high {Tc} superconductors. It has been shown that the probe can provide quantitative measurement of the full field penetration in superconducting samples by measuring the response of AC induced screening currents for superconducting materials in the form of tapes with overlayers of silver. In this manner, the AC probe can be used to replace the contact DC probe for determining critical currents in a noncontacting and local manner suitable for scanning over or along the sample.

Energy Technology Data Exchange (ETDEWEB)

This paper described the application of an AC surface probe, similar to presently used eddy current probes, to the measurement of DC transport critical currents and critical state dissipation in high [Tc] superconductors. It has been shown that the probe can provide quantitative measurement of the full field penetration in superconducting samples by measuring the response of AC induced screening currents for superconducting materials in the form of tapes with overlayers of silver. In this manner, the AC probe can be used to replace the contact DC probe for determining critical currents in a noncontacting and local manner suitable for scanning over or along the sample.

International Nuclear Information System (INIS)

Sep 1970. 85 p. United States Green, SJ LeTourneau, BW Peterson, AC Bettis

International Nuclear Information System (INIS)

English 1999 p. 47 Brazil Oliveira, JF Braga, ACS Avila, ASR Bernardo-Filho,

UK PubMed Central (United Kingdom)

Active Activator (Ac) elements undergo mutations to become nonautonomous Dissociation (Ds) elements at a low frequency. To understand...Full Text Available

International Nuclear Information System (INIS)

English 1998 p. 196 Brazil Oliveira, JF Braga, ACS Santos, JS Bernardo Filho,

British Library Electronic Table of Contents (United Kingdom)

A red basil cell line (T2b) rich in rosmarinic acid (RA) was selected for the stable production of anthocyanins (ACs) in the dark. Cell suspension cultures were subjected to mechanical stress through increased agitation (switch from 90 to 150rpm) to determine the relationship between AC and RA accumulation. Cell extracts were analyzed by HPLC and LC-MS, and the resulting data were processed with multivariate statistical analysis. MS and MS/MS spectra facilitated the putative annotation of several complex cyanidin-based ACs, which were esterified with coumaric acid and, in some cases, also with malonic acid. It was also possible to identify various RA-related molecules, some caffeic and coumaric acid derivatives and some flavanones. Mechanical stress increased the total AC and RA contents, ...

Science.gov (United States)

... impact. The Committee reviewed voluminous materials from NSF?s retrospective and prospective award ...

Energy Technology Data Exchange (ETDEWEB)

The effect of temperature (60-280{sup o}C) on the properties of the oxide films formed on Alloy 800 in 0.1 M NaCl and 0.1 M Na{sub 2}SO{sub 4} aqueous solutions was studied by in situ AC impedance spectroscopy and polarization in the Fe(CN{sub 6}){sup -3}/Fe(CN){sub 6}{sup -4} redox system. The anodic behavior under the same experimental conditions was examined by potentiodynamic polarization techniques. In both solutions the passive film was found to become more porous, and hence less protective, with increasing temperature. However, at temperatures above 150{sup o}C, the loss of film protectiveness is more pronounced in chloride solutions, in which pitting occurs. Pitting morphology was found to be strongly temperature dependent: isolated and deep pits were found up to 200{sup o}C whereas at higher temperatures a broad, shallow and more generalized type of attack was detected. No effect of temperature on the defect structure of the ...

International Nuclear Information System (INIS)

Liquid-liquid extractive separation of lithium isotopes was carried out in order to investigate the fluctuation of separation factors (a) as a function of salt concentrations in an aqueous phase. Two equations for separation factor (a_o_b_s) as a function of the concentration were introduced; one for the diluted region, and another for the concentrated region. In the former solution where hydrated lithium ions are predominant, 1n a_o_b_s = Ac + B, and in the latter where ion-pairs with anions are predominant, 1n a_o_b_s = Dc + E(c - F)"1"/"3 + G. Some guidelines are derived from the salt-specific constants A, B, D, E, F and G. The heavier isotopes are inclined to be in the more hydrated state in the diluted solution, while the lighter isotopes tend to be in a less hydrated state. In the concentrated solution, heavier isotopes are more likely to be in ion-pair form. Ionic association occurs from the lower concentration in the order of LiI < LiBr < LiCl. The ...

Energy Technology Data Exchange (ETDEWEB)

The object of this research is the evaluation of the performance of ultra high speed relays (UHSR's) used for protection of a-c transmission lines. For purposes of this report, these are relays whose response time is less than a quarter of a cycle of the 60 Hz wave (i.e. 4.167 ms.). To identify relaying schemes that may comply with this definition, a literature survey was undertaken. The selected relays were studied in detail and modeled on a digital computer. A theoretical description of these relays is presented. Records of real transient data as well as of simulated data were used as input to the digital models of relays. The real data were recorded by means of monitoring stations connected to the Florida Power and Light Company transmission lines. The simulated data were obtained by modeling the relevant parts of the utility's transmission system using a University of British Columbia simplified version of the well known ...

Science.gov (United States)

Up to the present, the generic values of the Common cause failure (CCF) event parameters have been used in most PSA projects for the Korean NPPs. However, the CCF analysis should be performed with plant specific information to meet Category II of the ASME PRA Standard. Therefore, we estimated the Alpha factor parameters of the emergency diesel generator (EDG) for Ulchin Unit 3 by using the International Common-Cause Failure data Exchange (ICDE) database. The ICDE database provides the member countries with only the information needed for an estimation of the CCF parameters. The Ulchin Unit A3, pressurized water reactor, has two onsite EDGs and one alternate AC (AAC) diesel generator. The onsite EDGs of Unit 3 and 4 and the AAC are manufactured by the same company, but they are designed differently. The estimation procedure of the Alpha factor used in this study follows the approach of the NUREG/CR-5485. Since we did not find any qualitative difference between the ...

International Nuclear Information System (INIS)

Based on the occurrence of a number of plant incidents during low power and shutdown operating conditions, the Nuclear Regulatory Commission (NRC) has initiated several programs to better quantify risk during these periods. One specific issue of interest is the loss of residual heat removal (RHR) under reduced coolant inventory conditions. This issue is also of interest in the Federal Republic of Germany and an experiment was performed in the integral PKL-3 experimental facility at Siemens-KWU to supply applicable data. Recently, an effort has been undertaken at the Idaho National Engineering Laboratory (INEL) to identify and analyze the important thermal-hydraulic phenomena in pressurized water reactors following loss of vital AC power and consequent loss of the RHR system during reduced inventory operation. The thermal-hydraulic response of a nuclear steam supply system (NSSS) with a closed reactor coolant ...

International Nuclear Information System (INIS)

We have previously shown that budded viruses of Bombyx mori nucleopolyhedrovirus (BmNPV) enter the cell cytoplasm but do not migrate into the nuclei of non-permissive Sf9 cells that support a high titer of Autographa californica multicapsid nucleopolyhedrovirus (AcMNPV) multiplication. Here we show, using the syncytium formation assay, that low-pH-triggered membrane fusion of BmNPV GP64 protein (Bm-GP64) is significantly lower than that of AcMNPV GP64 protein (Ac-GP64). Mutational analyses of GP64 proteins revealed that a single amino acid substitution between Ac-GP64 H155 and Bm-GP64 Y153 can have significant positive or negative effects on membrane fusion activity. Studies using bacmid-based GP64 recombinant AcMNPV harboring point-mutated ac-gp64 and bm-gp64 genes showed that Ac-GP64 H155Y and Bm-GP64 Y153H substitutions decreased and ...

Science.gov (United States)

Summary.? Measuring von Willebrand factor (VWF) activity is essential to the diagnosis of von Willebrand disease (VWD). The VWF activity is usually assessed based on measurement of the ristocetin cofactor (VWF:RCo). However, that test is technically challenging and has high intra- and inter-assay variabilities. The HemosIL VWF activity (VWF:AC) is a fully automated assay, recently proposed as a good alternative to VWF:RCo for VWD diagnosis. This study was undertaken to assess this new method. First, the analytical performance of VWF:AC on an automated coagulo-meter (ACLTop) was determined, and then this new method was compared with VWF:RCo and the platelet function analyzer (PFA100) for 160 patients referred for VWD screening. The VWF:AC achieved acceptable precision with within-run and between-run coefficients of variation ranging from 2.3% to 14.1%, and linearity from 10% to 100%. Despite some marked differences between ...

Energy Technology Data Exchange (ETDEWEB)

In this report an isolated PWM DC-AC SICAM with an active capacitive voltage clamp is presented. AC-DC power supply is implemented in its simplest form: diode rectifier followed by a medium-size charge-storage capacitors and possibly with an EMC filter on the mains entrance. Isolation from the AC mains is achieved using a high frequency (HF) transformer, whose voltages are not audio-modulated. The latter simplifies the design and is expected to have many advantages over the approach where the transformer voltages are modulated in regards to the audio signal reference. Input stage is built as a DC-AC inverter (push-pull, half-bridge or a full-bridge) and operated with 50% duty cycle, with all the challenges to avoid transformer saturation and obtain symmetrical operation. On the secondary side the output section is implemented as rectifier+inverter AC-AC stage, i.e. a true ...

British Library Electronic Table of Contents (United Kingdom)

Summary Fruit vinegar can be obtained biologically from the fermentation of fruit wine using species of the genera Acetobacter. However, the productivity of vinegar is generally low because of the inhibition by substrate ethanol and product acetic acid. In this research, the yield of acetic acid, as well as the cell growth, in hawthorn vinegar fermentation was enhanced using beer for seed preparation. The higher yield of acetic acid of AC2005 was because of the higher alcohol dehydrogenase and aldehyde dehydrogenase activities caused by using beer for seed preparation. Furthermore, Acetobacter pasteurianus AC2005 showed acid stability during the fed batch fermentation of hawthorn vinegar.

British Library Electronic Table of Contents (United Kingdom)

In this paper, a comparison is done between two different techniques in measuring the AC voltage. The first technique is the single junction thermal voltage converters (SJTVC) which consist of one thermal element (TE) which its output e.m.f. in the range of 7-12mV and the other is the new designed thermal voltage converters which consist of a number of TEs connected in parallel, series and series/parallel to increase their output e.m.f. (becomes in the range of 35-51mV). The effect of increasing the output e.m.f. is studied in this paper through evaluating the uncertainty budget and proved that its increase has a great effect on the accuracy and the uncertainty of the AC voltage measurement.

International Nuclear Information System (INIS)

Uranium and thorium ores are the source of natural radionuclides. Briefly described are the original and current methods of long-lived nuclide separation ("2"3"8U, "2"3"5U, "2"2"6Ra, "2"3"0Th, "2"3"1Pa, "2"2"7Ac, "2"3"2Th, "2"2"8Ra+"2"2"8Ac, "2"2"8Th), some short-lived nuclides ("2"3"4Th and "2"2"8Ac), radon, short-lived radon daughter products and long-lived radon daughter products ("2"1"0Pb, "2"1"0Bi, "2"1"0Po). Some nuclides, such as "2"1"0Po or "2"3"1Pa can more easily be producedin reactors. (Ha).

Science.gov (United States)

Electro-Magnet. Antenna Panels Types Simulated Hail Stone Damage A.Panel ...... X-Band Klystron Electro Magnet. 11. I I. 333-6104 AcBc. 333-6105 Color ...

Science.gov (United States)

the Advanced Distillation Curve, Energy & Fuels, Vol. 22, No. 2, pp. 11041114. http://pubs.acs.org/doi/full/10.1021/ef700562c. Lemmon, E. W., Huber, M. L., ...

UK PubMed Central (United Kingdom)

The synthesis of an extracellular ribbon of cellulose in the bacterium Acetobacter xylinum takes place from linearly arranged, membrane-localized, cellulose-synthesizing and extrusion complexes that...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundAdhesive Capsulitis (AC) affects patient of all ages, and stretching protocols are commonly prescribed for this condition. Dynamic splinting has been shown effective in...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This report covers the test methods and equipment for testing aircraft armor both hard and soft. The hard armor are the typical ceramic type while the soft armor are various types of layered composite materials. 10 figs. (JEF)

Energy Technology Data Exchange (ETDEWEB)

Alloy 800 is an austenitic Fe-Ni-Cr steel containing relatively minor but important amounts of carbon, aluminium and titanium. Special grades of alloy 800 known as 800H, 800HT and 800LC differ in the concentrations of these elements. In addition to these industrial specifications, further melts were prepared containing phosphorous or sulphur. Using a radioactive tracer method the bulk and grain-boundary diffusion of {sup 59}Fe was investigated in these alloys in the temperature range 800 to 1000 C. For evaluation of the diffusion profiles the approximation of Suzuoka was used, which considers the depletion of the tracer on the surface. By autoradiography it was confirmed that such depletion occurs. In alloy 800H the activation energy of grain-boundary diffusion of {sup 59}Fe was found to be (209{+-}17) kJ/mol; dissolved elements, especially phosphorous, increase the activation energy. The same materials - aged at 800 C for 100 h - were used for creep experiments at 800 C under constant ...

International Nuclear Information System (INIS)

We present an approach for fabrication of intentionally positioned epitaxial InAs QDs in a micron sized light emitting diode. For site-selective growth, a combination of molecular beam epitaxy (MBE) and focused ion beam (FIB) implantation technology in an all-ultra-high-vacuum (UHV) setup has been employed. Single dot occupancy of almost 55 % on FIB patterned nano-depressions was successfully achieved. Thereafter, carrier injection and subsequent radiative recombination from the positioned InAs/GaAs self-assembled QDs was investigated by embedding these QDs in the intrinsic part of a GaAs-based micron sized p-i-n junction device. Few or single dot are expected to be electrically addressed in these devices. We report results from electroluminescence (EL) measurement which proves the single dot characteristics of our device. The EL spectra consist of sharp emission lines and their dependence on injection current shows linear behavior for exciton and quadratic ...

Energy Technology Data Exchange (ETDEWEB)

The usefulness of radioiodination via demetallation of aryltrimethylsilanes was demonstrated. The radioiodination reaction was found to be very rapid and the regiospecific incorporation of radioiodine could be carried out with high radiochemical yields and high radiospecific activity. {sup 125}I-Labeled dimethylaminoethyl iodophenoxyacetate derivatives (5a-e), dimethylaminoethyl iodophenoxyacetamide derivatives (7a-c), iodophenoxyethyl ethylenediamine derivatives (9,14) and an iodophenoxyethylpiperazine derivative (18) were efficiently synthesized from the corresponding aryltrimethylsilyl intermediates (4a-e, 6a-c, 8, 13, 17) by this method. (author).

Wastenet

... John Cannaday and Ken Weddle present the framework for a Product Design Engineering project (http://engineering.dartmouth.edu/~teps/images/ProductDesign.pdf) for high school students which may have relevance at a more advanced level. David Price has created a Mechanical Engineering Design (http://www.soton.ac.uk/~cds/) site containing engineering design notes. The Virtual Reality Engineering Library Home Page at the University of Bristol (http://www.dig.bris.ac.uk/virtual_lib/) is a library ...

Energy Technology Data Exchange (ETDEWEB)

The baseline design for the SSC High Energy Booster (HEB) has dipole bending magnets with a 50 mm aperture. An analysis of the cryogenic heat load due to A.C. losses generated in the HEB ramp cycle are reported for this magnet. Included in this analysis are losses from superconductor hysteresis, yoke hysteresis, strand eddy currents, and cable eddy currents. The A.C. loss impact of 2.5 {mu}m vs. 6 {mu}m filament conductor is presented. A 60 mm aperture design is also investigated. 8 refs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

This study was designed to identify abnormalities in the hepatic-arterial/portal-venous scintiangiogram (SA) in alcoholic hepatitis (AH). SA's were performed in 35 patients with acute alcoholic hepatitis (AAH), 8; acute alcoholic hepatitis superimposed on cirrhosis (A/C), 14; and cirrhosis (C), 13. Posterior flows were done with a bolus of 10 mCi Tc-99m sulfur colloid with computer time-activity curves over the liver and left kidney. Curves were analyzed for per cent of hepatic arterial (HA) and portal venous contribution using the slope ratio method. Hepatic arterialization was estimated from the angle of the HA component of the curve. Reversal of the relative contribution of the hepatic and portal components of total flow were seen in all groups. Although quite severe in AH, the degree of reversal could not be used to differentiate among the groups. The average HA angle in AAH was 48.3 +- 8.1, in A/C 41.5 +- 10.6, and in C 30.4 +- ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes a 1993 field experiment entitled Marine Aerosol Properties and Thermal Imager Performance Trial (MAPTIP) conducted by NATO AC/243 Panel 04/RSG.8 and 04/RSG.5 in the Dutch coastal waters. Objectives were: to improve and validate vertical marine aerosol models by providing an extensive set of aerosol and meteorological measurements, within a coastal environment at different altitudes and for a range of meteorological conditions; make aerosol and meteorological observations in the first 10 m of the ocean surface with a view to extending existing aerosol models to incorporate near-surface effects; and to assess marine boundary layer effects on thermal Imaging systems. Aerosol and meteorological instruments, as well as thermal imagers and calibrated targets, were utilized. This network of instrumentation has provided a comprehensive database of aerosol size distribution profiles and relevant meteorological variables throughout ...

Energy Technology Data Exchange (ETDEWEB)

The paper begins with an introduction on the reasons that lead to the use of HVDC submarine cable links. The main aspects for the choice of direct current are presented as well as the advantages deriving from the utilization of submarine cables. The second part is dedicated to a discussion on the various type of insulation that could be used in power cables and their possible application to HVDC submarine cables. In the following there is a description of the main characteristics and technical details of some particular project that at present time (1995) are in progress. Two projects are briefly presented: Spain-Morocco, a 26 km long interconnection for the transmission, in a first phase, of 700 MW from Spain to Morocco at 400 kV a.c. by means of three cables, plus one spare, of the fluid filled type. The cables are designed for a future change to d.c. 450 kV, allowing a transmission of 500 MW each (i.e., 2 GW total). One of the peculiarities of the link is the ...

International Nuclear Information System (INIS)

Alloy 600 is commonly used in the primary systems of PWR plants because of its excellent resistance to a stress corrosion cracking and pitting. But a stress corrosion cracking and pitting corrosion are occasionally observed under PWR conditions, which may be correlated with the passive film on the Alloy 600 surface. There is little information on the composition of films growing on the surface of Alloy 600 at high temperature. Therefore, an understanding of the basic electrochemical behaviors about an anodic dissolution and the passivation of the bare surface of metals and alloys provides important information about localized corrosions like a SCC and pitting. Oxide on the steel surfaces in an aqueous solution above 100 .deg. C is composed of a duplex film structure. The inner layer of the oxide is dense and less porous, which is formed by a growth of the oxide layer on the metal surface. Outer layer of the oxide is less adhesive, which is formed by a dissolution ...

British Library Electronic Table of Contents (United Kingdom)

Previous research utilizing the AcB/BcA recombinant congenic strains (RCS) of mice mapped provisional quantitative trait loci (QTLs) for the psychostimulant effects of nicotine to multiple regions on chromosomes 7, 11, 12, 14, 16, and 17. The current study was designed to confirm these QTLs in an A/J (A)??C57Bl/6J (B6) F2 cross and a panel of B6.A chromosome substitution strains (CSS). The panel of B6.A CSS consists of 21 strains, each carrying a different A/J chromosome on a B6 background. The A??B6 F2, CSS, A, and B6 mice were tested for sensitivity to the effects of nicotine on locomotor activity using a computerized open-field apparatus. In A??B6 F2 mice two QTLs were identified which confirm those previously observed in the AcB/BcA RCS. Significant differences in the expression of ...

British Library Electronic Table of Contents (United Kingdom)

Objectives Clinical PET/MR requires the use of patient positioning aids to immobilize and support patients for the duration of the combined examination. Ancillary immobilization devices contribute to overall attenuation of the PET signal, but are not detected with conventional MR sequences and, hence, are ignored in standard MR-based attenuation correction (MR-AC). We report on the quantitative effect of not accounting for the attenuation of patient positioning aids in combined PET/MR imaging. Methods We used phantom and patient data acquired with positioning aids on a PET/CT scanner (Biograph 16, HI-REZ) to mimic PET/MR imaging conditions. Reference CT-based attenuation maps were generated from measured (original) CT transmission images (origCT-AC). We also created MR-like attenuation map...

International Nuclear Information System (INIS)

The thermal properties (thermal conductivity, thermal diffusivity, thermoelectric power, thermal dilatation, etc.) and the mechanical properties (Young's modulus, strength, hardness, fracture toughness, etc.) have been measured at low temperatures (4-300K) and under a high magnetic field (0-10T) for about 50 REBaCuO bulks (RE=Y, Gd, Nd, Sm, Dy, etc.). We have constructed the database of these properties and opened it on the Web site (thermal properties: http://ikebehp.mat.iwate-u.ac.jp/database.html and mechanical properties: http://paris.mech.iwate-u.ac.jp/sc-bulk/database.html). The influence of the species of RE ions, the content, size and dispersion of the RE211 (or Nd422) phase and Ag particles and the defects distribution on these properties is characterized.

Science.gov (United States)

N F Q k q V N h l b hs x j p bN t gX Y I r bN X U Y Fff c o t dA A p A DA2 AC7LAR A Ak VAwt A jA A A A t A bNA A A dZA A A A A A X A A M A LA A E A A wA V A A A A oA V A A oA M A...

Science.gov (United States)

Organic molecules are a significant and highly varied component of atmospheric aerosols. Measurement of aerosol composition and improvements in our understanding of the complex chemistry involved in their formation and aging are being aided by innovations in soft ionization aerosol MS. (To listen to a podcast about this feature, please go to the Analytical Chemistry multimedia page at pubs.acs.org/page/ancham/audio/index.html.). PMID:21275431

Energy Technology Data Exchange (ETDEWEB)

In this first quarterly technical report for DOE Contract No. DE-AC22-87PC79654, a description of the background, technology, and application is provided. The design and fabrication of advanced combustion chambers were completed during this period. Initial testing on both the bare metal and refractory lined advanced chambers were initiated. The units were tested initially with gas but primarily with coal. A Pittsburgh No. 8 pulverized coal was used for these test activities. Both advanced chambers pulsed well.

UK PubMed Central (United Kingdom)

Background:Acute Coronary Syndrome (ACS) can occur in patients with prior coronary artery bypass grafting (CABG). In the Gulf Registry of acute coronary events (Gulf RACE), we identified...Full Text Available

Wastenet

... Further information For more detailed information on available accommodation, refer to our housing guide At home with us, visit Residential Services, or contact : T +44 (0)1273 678220 E housing@sussex.ac.uk Davidrsquo;s perspective lsquo;When my wife and I decided to study at Sussex, we applied for University accommodation. We were delighted with the lovely self-contained flat on Clifton Road in Brighton that we got via the Housing Office. ...

Energy Technology Data Exchange (ETDEWEB)

The Minami-Iwaki trunk line now under construction by Tokyo Electric Power Company is an UHV transmission line which covers 130km from the central region of the Abukuma highlands, Fukushima Prefecture, through the northern ridge of the Kanto Plain to Imaichi City, Tochigi Prefecture and has 235 steel towers. About 30% of the ground along the above route is mainly layers of sand and gravel. Accordingly it has become urgent to design rationally the pile foundations in the sand and gravel layers. Hence the company has studied an estimation method of the ultimate bearing power of cast-in-place piles penetrating the sand and gravel layers and the displacement of pile heads. In this report, the result of the above study is described. The company has so far used the equations in accordance to the Meyerhof equations for the estimations of the ultimate bearing power and this time, this equations have been examined for its application to the sand and gravel layers, and for ...

Science.gov (United States)

NFAT involvement in adipocyte physiological processes was examined by treatment with CsA and/or GSK3{beta} inhibitors (Li{sup +} or TZDZ-8), which prevent or increase NFAT nuclear translocation, respectively. CsA treatment reduced basal and TNF{alpha}-induced rates of lipolysis by 50%. Adipocytes preincubated with Li{sup +} or TZDZ-8 prior to CsA and/or TNF{alpha}, exhibited enhanced basal rates of lipolysis and complete inhibition of CsA-mediated decreased rates of lipolysis. CsA treatment dramatically reduced the mRNA levels of adipocyte-specific genes (aP2, HSL, PPAR{gamma}, ACS and Adn), compared with control or TNF{alpha}-treatment, whereas Li{sup +} pretreatment blocked the inhibitory effects of CsA, and mRNA levels of aP2, HSL, PPAR{gamma}, and ACS were found at or above control levels. NFAT nuclear localization, assessed by EMSA, confirmed that CsA or Li{sup +} treatments inhibited or increased NFAT nuclear translocation, respectively. ...

Energy Technology Data Exchange (ETDEWEB)

The behaviour of hydrogen adsorption on palladium has been investigated by a.c. impedance measurements in 0.1 M NaOH solution of pH 13 at 298 K. The electrode impedance has been measured by superimposing an a.c. voltage of 5 mV amplitude ranging between 10{sup -1} and 10{sup 4} Hz on a d.c. potential range from -0.76 to 0.44 V (standard hydrogen electrode (SHE)). The equivalent circuit representing the hydrogen adsorption reaction is proposed from the analysis of the frequency dependence of electrode admittance. The capacitance, arising from the adsorbed hydrogen, has been determined as a function of applied potential by complex non-linear least-squares curve fitting method based on the proposed equivalent circuit. As the cathodic applied potential increased from -0.36 to -0.76 V (SHE), the adsorption capacitance considerably increased owing to the enhanced coverage of hydrogen adsorbed on the palladium surface. In the applied potential range ...

Energy Technology Data Exchange (ETDEWEB)

The electrode kinetics for oxygen reduction on conducting metal oxides, including lithiated NiO (formed in situ) and Sb-doped SnO/sub 2/, have been investigated. Kinetic measurements were carried out by using ac impedance and coulostatic relaxation methods. The ac behavior on the oxide electrodes was analyzed on the basis of a modified Randles-Ershler type equivalent circuit which takes into account the effect of non-faradaic components due to the semiconducting oxide films. The kinetic parameters (the charge transfer resistance and Warburg coefficient) and the interfacial parameters (the double layer capacity, film capacity and film resistance) were obtained by a least squares curve fitting method under P/sub O2//P/sub CO2/=0.9/0.1 atmosphere. The exchange current density was found to be 10 to 20 mA cm/sup -2/ at the oxide electrodes, assuming n=2. The coulostatic relaxation experiments supported the magnitude of the i/sub o/ values.

Energy Technology Data Exchange (ETDEWEB)

Type 440C stainless steel is a high-C, high-Cr martensitic steel used in applications requiring high hardness and wear resistance in combination with moderate corrosion resistance. Typical applications include precision aerospace bearings and critical components in computer disk drives. The properties of passive films formed on 440C steel were investigated using advanced electrochemical techniques with a view to establishing a method to measure film stability directly in the passivation baths. Electrochemical measurements were sensitive to the passive film properties and were able to quantify the effect of cooling rate on passive film stability. The techniques used included linear polarization, AC impedance, small amplitude cyclic voltammetry, and coulostatic transient measurements. These provided results that exhibited excellent agreement with the AC impedance technique providing the most information about the interfacial reactions. It was ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Visible blue cathodoluminescence (CL), photoluminescence (PL), x-ray excited optical luminescence (XEOL) and electroluminescence (EL) via Zf free excitonic emission have been obtained from CuBr thin films deposited on glass, Cr coated glass, GaAs and Si substrates. In addition to the Zf emission several peaks corresponding to Cu+ emissions via 3d94s - d10 transitions were observed on the AC EL spectrum at 2.10, 2.7, 3.03, 3.07 and 3.80 eV. X-ray diffraction (XRD) measurements confirmed that the vacuum evaporated CuBr thin films grow preferentially with a (111) orientation irrespective of the substrate. While the AC voltage source was found to have no detrimental effects on CuBr thin films, cathodic deposition of Cu metal via electrolytic decomposition was observed under steady sta...

Energy Technology Data Exchange (ETDEWEB)

Tests have recently been performed at Fermilab in order to measure the energy losses due to eddy currents and iron and superconductor magnetization. These measurements were performed on six 1.5m long model magnets and eight 15m long full scale collider dipole magnets. AC losses were measured as a function of ramp rate using sawtooth ramps from 500, to 5000 Amps for both types of magnets, while bipolar studies were additionally performed on some of the short magnets. The measured magnet voltage and current for a complete cycle are digitally integrated to yield the energy loss per cycle. Measurement reproducibility is typically 5%, with good agreement between long magnet measurements and extrapolations from short magnet measurement results. Magnetization loss measurements among similar magnet types agree to within experimental error, while eddy current losses correlate strongly with the observed dependence of quench current on ramp rate.

Energy Technology Data Exchange (ETDEWEB)

The principle of conservation and transferability of chemical bonds explains the recent discovery by extended x-ray absorption fine-structure measurements of two unequal anion-cation bond lengths R/sub A/C and R/sub B/C in A/sub x/B/sub 1-x/C zinc-blende semiconductor alloys despite the close adherence of the lattice constant to the average value (Vegard rule). This bond alternation, manifested as a structural distortion to a local chalcopyrite coordination around the anions, explains also most of the observed optical bowing in semiconductor alloys.

International Nuclear Information System (INIS)

The excess energy of several III-V and II-VI strained-layer semiconductor superlattices (AC)_p(BC)_p is studied as a function of the repeat period p and orientation G=[001], [110], [111], and [201], using first-principles calculations. We discover a number of universal features, including the predicted instability for nearly all p's and G's with respect to bulk disproportionation, the identification of chalcopyrite as a metastable ordered structure, and the stability of all thin epitaxial [110] and [201] and most common-anion [001] superlattices relative to coherent phase separation.

Energy Technology Data Exchange (ETDEWEB)

The accuracy of the carbon 14 dating method is dependent on the fluctuations of carbon 14 in the atmosphere over long periods of time. Fossil corals that are dated by both carbon 14 and uranium-thorium methods allows the setting of calibration curves for the carbon 14 method for the last 50.000 years. The uranium-thorium method is based on the measurement of the ratio of 2 isotopes: thorium 230 and uranium 234 that are both present in the decay chain of uranium 238. (A.C.)

Energy Technology Data Exchange (ETDEWEB)

Probability distributions of partial discharge (PD) and dielectric breakdown voltage were investigated for the typical components of oil-filled transformer insulation. The equi-probabilistic PD and BD V-t characteristics were obtained from experimental results in the time range from several ..mu..sec to 10 hours. The authors point out that there is a close relationship between the scattering of PD voltage and the inclination of V-t characteristics in a long term region for ac voltage.

International Nuclear Information System (INIS)

The #pi#g_9_/_2 band structure in "1"2"1Cs is obtained. The experiment was performed at the HI-13 MV tandem accelerator of China Institute of Atomic Energy. The excited states of "1"2"1Cs were populated via the reaction "1"1"2Sn("1"2C, p2n). The #gamma#-#gamma# coincidence data were taken with five BGO-AC HpGe detectors at beam energy of 60 Mev. The energy-level schemes of "1"2"1Cs is presented.

Energy Technology Data Exchange (ETDEWEB)

Two thirds of the neutrinos produced in the sun are not detected. In the last decade several experiments have allowed to give a limit to the neutrino mass and in some cases a negative value of the square of the mass was proposed. A negative value is inconsistent theoretically except in the case of tachyons which are particles allowed to travel faster than light. Consider neutrinos as tachyons could be a solution to find the answers to some of the riddles set by neutrinos. (A.C.)

Wastenet

...CanCom Dermatology Image Bank Dermatology Online Atlas Introduction to Skin Cancer Malignant Melanoma Skin Cancer (Not Melanoma) Comments: bubl@bubl.ac.... Covers anatomy, melanoma, infections, and dermatological disorders in AIDS. Author: University of Utah ...994 Resource type: document Malignant Melanoma This leaflet on malignant melanoma covers early detection, causes, clinical signs and symptoms, and provides ...9 Resource type: document Skin Cancer (Not Melanoma) Information on basal cell and squamous cell skin cancers. Author: ...

British Library Electronic Table of Contents (United Kingdom)

This study investigated the association between differences in litter size in Boer does, with genetic polymorphisms in the inhibin alpha gene. Our preliminary (n=209) results found 12 SNPs, including the non-synonymous polymorphisms 911T/C and 946A/C, resulting in corresponding 299V/A and 311T/P amino acid polymorphisms. Of the SNPs, 651A/G was preliminarily suggested as a useful marker for litter size of the second parity in the population studied, showing an overdominance effect. Polymorphisms, sequence, and genotype distributions were also characterized.

Energy Technology Data Exchange (ETDEWEB)

The feasibility of the anodic protection of titanium evaporators in Al[sub 2](SO[sub 4])[sub 3] solution was studied by the measurement of polarization curves, weight loss, solubility of passive film and AC impedance. The protection parameters and efficiency were determined. In addition, the practical technology of anodic protection was studied by screening reference electrodes and auxiliary cathodes. Throwing power was also measured. Four rows of tube-type evaporators of titanium have been anodically protected in situ. Field tests lasting more than one year shows satisfactory results. (orig.)

International Nuclear Information System (INIS)

The properties of the passive films formed on Alloy 600 at different applied potentials in 10% NaOH solution at 315 .deg. C was studied using in situ AC impedance and polarization measurements. The results were correlated with the stress corrosion cracking (SCC) behavior obtained from the C-ring tests in the same conditions. The change of the semiconductive property and the peak of relaxation time were observed at 0.2 V where the SCC rate showed a maximum. These results were also consistent with the prediction parameter for SCC obtained from fast and slow polarization scans.

Energy Technology Data Exchange (ETDEWEB)

Activated carbons (ACs) were prepared from chicken waste (CW) and coal (E-coal) blended at the ratios of 100:0, 80:20, 50:50, 20:80, and 0:100. The process included carbonization in flowing gaseous nitrogen (300 mL min{sup -1}) at ca. 430{sup o}C for 60 min and successive steam activation (0.1 mL min{sup -1} water injection with a flow of N{sub 2} at 100 mL min{sup -1}) at 650{sup o}C for 30 min. Chicken waste is low in sulfur content but is high in volatile matter (about 55 wt %), and ACs with higher specific surface area were more successfully obtained by mixing with coal. The specific surface area of the CW/Coal blend AC can be estimated by SSA{sub BET} = -65.8x{sup 2} + 158x + 168, where SSA{sub BET} is the specific surface area in m{sup 2} g{sup -1} as determined by the BET method using CO{sub 2} as the adsorbent, where x is the coal fraction by weight in the CW/coal blend ranging from 0.0 to 1.0 (e.g., x = 0.0 ...

International Nuclear Information System (INIS)

We have previously reported that FSH stimulates flux of 45Ca2+ into cultured Sertoli cells from immature rats via voltage-sensitive and voltage-independent calcium channels. In the present study, we show that this effect of FSH does not require cholera toxin (CT)- or pertussis toxin (PT)-sensitive guanine nucleotide binding (G) protein or activation of adenylate cyclase (AC). Significant stimulation of 45Ca2+ influx was observed within 1 min, and maximal response (3.2-fold over basal levels) was achieved within 2 min after exposure to FSH. FSH-stimulated elevations in cellular cAMP paralleled increases in 45Ca2+ uptake, suggesting a possible coupling of AC activation to 45Ca2+ influx. (Bu)2cAMP, however, was not able to enhance 45Ca2+ uptake over basal levels at a final concentration of 1000 microM, although a concentration-related increase in androstenedione conversion to estradiol was evident. Exposure of Sertoli cells to CT (10 ng/ml) ...

International Nuclear Information System (INIS)

Electron-beam codeposition of the elements to form certain high critical temperature superconducting materials, in particular A-15 compounds, has proven to be very useful in research directed at understanding and improving their superconducting properties. This work has used the close control of three or more evaporant sources to reproducibly make specimens that permit studies across selected regions of composition and phase space. The effect of composition and phase, together with the temperature and rate of deposition, on the growth morphology and superconducting properties has been studied. The superconducting properties measured include the critical temperature, ac loss, critical current density, and tunnel junction characteristics. The particular compounds studied include Nb_3Sn, Nb_3Ge, and V_3Si.

British Library Electronic Table of Contents (United Kingdom)

The condensation reaction of furfural (F) on acetone (Ac) gives a high added value product, the 4-(2-furyl)-3-buten-2-one (FAc), used as aroma in alcohol free drinks, ice, candies, gelatines and other products of current life. This synthesis valorises the residues of sugar cane treatment since furfural is obtained by hydrolysis of sugar cane bagasse followed by vapor training extraction. In the face of numerous and complex reactions involved in this synthesis, it is very complicated to define the kinetic laws from exact stoichiometry. A solution allowing to cope the problem consists in identifying an appropriate stoichiometric model. It does not attempt to represent exactly all the reaction mechanisms, but proposes a mathematical support to integrate available knowledge on the transformati...

Energy Technology Data Exchange (ETDEWEB)

The spin relaxation processes within the pyrochlore Ho{sub 2}Ru{sub 2}O{sub 7} have been investigated by neutron scattering and bulk property techniques. A single-ion process, that is thermally activated, dominates the spin-spin relaxation spectrum above 2 K. Assuming Arrhenius behaviour, we found an activation energy {delta} = (329 {+-} 6) K and characteristic relaxation time {tau}{sub 0} (5.2 {+-} 0.3) x 10{sup -12} s in the paramagnetic state, akin to those found in the spin ice, Ho{sub 2}Ti{sub 2}O{sub 7}. Atlow temperature (T<95 K) the activation energy lowers and below 20 K the entropy and ac susceptibility are similar to that observed in other spin ice compounds within a 10 kOe field.

Energy Technology Data Exchange (ETDEWEB)

In this report we present an update on the results from the Amanda-B10 detector which operated in 1997 at depths of 1500 to 2000 meters in the deep Antarctic ice. The goal of Amanda project is to search for extra-terrestrial neutrinos. As a precursor to such a search we have studied atmospheric neutrinos which act as a calibration source for the detector. The observation of atmospheric neutrinos at a rate consistent with Monte-Carlo predictions establishes Amanda-B10 as a neutrino telescope. The Amanda-B10 data has been searched for evidence of several classes of neutrinos and for magnetic monopoles. Searches for a diffuse high energy neutrino flux and for neutrinos in coincidence with gamma-ray bursts have been conducted. Preliminary data analyses show no excess of neutrinos has been found. (A.C.)

International Nuclear Information System (INIS)

We report on the improvement of Critical Dimension (CD) linearity on a photomask by applying the concept of process proximity correction to a laser lithographic process used for fabrication of photomasks. Rule-based Laser Process proximity Correction (LPC) was performed using an automated optical proximity correction tool and we obtained dramatic improvement of CD linearity on a photomask. A study on model-based LPC was executed using a two-Gaussian kernel function and we extracted model parameters for the laser lithographic process by fitting the model-predicted CD linearity data with measured ones. Model-predicted bias values of isolated space (I/S), Arrayed Contact (A/C) and Isolated Contact (I/C) were in good agreement with those obtained by the nonlinear curve-fitting method used for the rule-based LPC.

Energy Technology Data Exchange (ETDEWEB)

Boiling jet impingement cooling is currently being explored to cool power electronics components. In hybrid vehicles, inverters are used for DC-AC conversion. These inverters involve a number of insulated-gate bipolar transistors (IGBTs), which are used as on/off switches. The heat dissipated in these transistors can result in heat fluxes of up to 200 W/cm{sup 2}, which makes the thermal management problem quite important. In this paper, turbulent jet impingement involving nucleate boiling is explored numerically. The framework for these computations is the CFD code FLUENT. For nucleate boiling, the Eulerian multiphase model is used. The numerical results for boiling water and R113 jets (submerged) are validated against existing experimental data in the literature. Some representative IGBT package simulations that use R134a as the cooling fluid are also presented. (author)

British Library Electronic Table of Contents (United Kingdom)

Side-chain liquid crystalline ionomer (SLCI) containing sulfonic acid groups with a polymethylhydrosiloxane main-chain was used in the blends of polypropylene (PP) and polybutylene terephthalate (PBT) as a compatibilizer. The crystalline behavior, morphological, and mechanical properties of the blends were investigated in detail by differential scanning calorimetry (DSC), polarizing optical microscope (POM), Fourier transforms infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Revealed by the shift of Tm in DSC thermogram and the shift of the absorbed peak in FTIR spectra, specific interaction led to stronger interfacial adhesion between these phases, which resulted in much finer dispersion of the minor PBT phase in PP matrix. The SLCI containing sulfonate acid groups ac...

International Nuclear Information System (INIS)

We have simulated the transient enhanced diffusion (TED) of boron fluoride (BF_2"+) implanted in crystalline and germanium amorphized silicon. Based on recently published models, the effect of fluorine on boron diffusion in silicon has been introduced and a modelling has been suggested. In order to simulate the boron experimental profiles, we have assumed that fluorine forms clusters involving interstitial boron which reduces the junction depth. Experimental results indicate that fluorine behaviour depends on amorphization energy. Moreover, even no germanium preamorphization is performed, silicon is still amorphized by fluorine species. Hence, BF_2"+ implantation leads to an amorphous/crystalline (a/c) interface near the surface. An improvement of published models is suggested taking into account fluorine effects. The simulations satisfactory reproduce the SIMS experimental profiles for a large scale of experimental conditions.

International Nuclear Information System (INIS)

Orbit correction is now routinely performed at the few-micron level in the Advanced Photon Source (APS) storage ring. Three diagnostics are presently in use to measure and control both AC and DC orbit motions: broad-band turn-by-turn rf beam position monitors (BPMs), narrow-band switched heterodyne receivers, and photoemission-style x-ray beam position monitors. Each type of diagnostic has its own set of systematic error effects that place limits on the ultimate pointing stability of x-ray beams supplied to users at the APS. Limiting sources of beam motion at present are magnet power supply noise, girder vibration, and thermal timescale vacuum chamber and girder motion. This paper will investigate the present limitations on orbit correction, and will delve into the upgrades necessary to achieve true sub-micron beam stability.

British Library Electronic Table of Contents (United Kingdom)

This study compares two series of solvents for application in aluminum electrolytic capacitors: ethylene glycol (EG) and water mixtures, and ethylene glycol and 1-n-butyl-3-methylimidazolium tetrafluoroborate (BMI.BF4) ionic liquid (IL) mixtures. Electrochemical impedance spectroscopy and cyclic voltammetry were carried out with a previously anodized aluminum disk electrode. Comparative measurements of solution resistance, polarization resistance, AC capacitance, and passive current were made. The results show that EG?IL mixtures with low amounts of IL (10% IL?90% EG v/v) have a low solution resistance. Low values of solution resistance, high values of polarization resistance, small passive current, and uniform capacitance of anodized aluminum in EG?IL mixtures are favorable properties of ...

British Library Electronic Table of Contents (United Kingdom)

Sols of silver nanoparticles in toluene were studied by broadband dielectric spectroscopy (10?3?105 Hz). The frequency dependences of the specific alternating current (ac) conductivity and the complex electric modulus were used to estimate the temperature/frequency intervals of long- and short-range charge transfer occurs, respectively. A considerable increase (by more than 30 ?C) in the Vogel temperature T 0 and the glass transition temperature T g in sols compared with the pure solvent was found. It can be hypothesized that these cooperative effects reflect the initial stage of the superlattice formation. Although the dielectric characteristics of sols are generally controlled by the conductivity relaxation, the dielectric response was observed in the high-frequency range (1?103 Hz) at l...

British Library Electronic Table of Contents (United Kingdom)

The development of a new configuration of chemical ionization (CI)-based ion source is presented. The ambient air containing the gaseous sample is sniffed into an enclosed ionization chamber which is of sub-ambient pressure, and is subsequently mixed with metastable species in front of the ion inlet of the mass spectrometer. Metastable helium atoms (He*) are used in this study as the primary ionizing agents and are generated from a dielectric barrier discharge (DBD) source. The DBD is powered by an AC high-voltage supply and the configuration of the electrodes is in such a way that the generated plasma is confined within the discharge tube and is not extended into the ionization chamber. The construction of the ion source is simple, and volatile compounds released from the bulky sample can...

DEFF Research Database (Denmark)

We present a theoretical study of the resonant interaction between dynamical localized states (discrete breathers) and linear electromagnetic excitations (EE's) in Josephson junction ladders. By making use of direct numerical simulations we find that such an interaction manifests itself by resonant steps and various sharp switchings (voltage jumps) in the current-voltage characteristics. Moreover, the power of ac oscillations away from the breather center (the breather tail) displays singularities as the externally applied dc bias decreases. All these features may be mapped to the spectrum of EE's that has been derived analytically and numerically. Using an improved analysis of the breather tail, a spectroscopy of the EE's is developed, The nature of breather instability driven by localized EE's is established.

International Nuclear Information System (INIS)

The level structure of "2"1"2Bi has been studied by observing the alpha decay of "2"1"6At which is in secular equilibrium with "2"2"0Fr and "2"2"4Ac. Eight states are observed and tentatively assigned to the configuration #pi#h_9_/_2#nu#(g_9_/_2)"3 and three to the configuration #pi#h_9_/_2#nu#(g_9_/_2)"2i_1_1_/_2. These two lowest configurations in "2"1"2Bi are compared with the corresponding configurations in "2"1"0Bi and the calculations of Warburton.

International Nuclear Information System (INIS)

We use deep HST/ACS observations to calculate the star formation history (SFH) of the Cetus dwarf spheroidal (dSph) galaxy. Our photometry reaches below the oldest main-sequence turnoffs, which allows us to estimate the age and duration of the main episode of star formation in Cetus. This is well approximated by a single episode that peaked roughly 12 #+-# 0.5 Gyr ago and lasted no longer than about 1.9 #+-# 0.5 Gyr (FWHM). Our solution also suggests that essentially no stars formed in Cetus during the past 8 Gyr. This makes Cetus' SFH comparable to that of the oldest Milky Way dSphs. Given the current isolation of Cetus in the outer fringes of the Local Group, the dominant old population implies that Cetus is a clear outlier in the morphology-Galactocentric distance relation that holds for the majority of the Milky Way dwarf satellites. Our results also show that Cetus continued forming stars until z#approx =# 1, long after the universe was reionized, and that ...

International Nuclear Information System (INIS)

Superconducting generators for high power applications have been of interest for a number of years. Superconducting generators using low temperature superconductors (LTS) have been manufactured to produce up to 20 MW of electrical power and have been configured in either synchronous alternators which have an AC output that may be subsequently rectified to produce DC and homopolar generators which produce low voltage DC. Typically these generators require scrupulous attention to vacuum integrity for cryogenic insulation at 4.2K and tend to be somewhat fragile because of extensive thermal and magnetic shields that are not required in conventional power generators. Recently, high purity aluminum composites have been developed for a high power AC generator that is cooled by cryogenic hydrogen at 21K. This aluminum generator is very compact and lightweight and is much more robust than a generator made with LTS because extensive thermal and magnetic ...

CERN Document Server

Mobile Information Systems

Wastenet

...Floating systems - Atkins storage and offloading units (FPSOs). ...

CERN Document Server

Bose-Einstein condensation in nonlinear system

Science.gov (United States)

Directed evolution of proteins depends on the production of molecular diversity by random mutagenesis. While a number of methods have been developed for introducing this diversity, the best ways to sample it are not always clear. Here we used simple statistics to analyse completeness and diversity in randomized libraries generated by oligonucleotide-directed mutagenesis, error-prone polymerase chain reaction (epPCR) and in vitro recombination of highly homologous sequences. For oligonucleotide-directed mutagenesis, we derive equations to estimate how complete a given library is expected to be and also to predict the size of library required to give a fixed probability of being 100% complete. We describe the statistical bases for computer programs which estimate the number of distinct variants represented in epPCR and shuffled libraries, dubbed PEDEL and DRIVeR, respectively. These programs allow the user to calculate (rather than guess) the diversity represented in a given library and ...

Science.gov (United States)

Separate comprehensive final reports on the status of the SRC-II Demonstration Plant Design and on operating experiences at the Ft. Lewis and P-99 SRC pilot plants were prepared after the termination of those projects. However, time constraints made it impossible to consolidate all of the pilot plant data and operating experiences and relate these to the Demonstration Plant or future plant design. Most of the experimental programs during the later stages of pilot plant operation were in direct support of specific technical uncertainties identified in design work. The results of these programs would have been of substantial use in verifying or modifying design philosophy had the project proceeded. This technical data analysis project was undertaken to consolidate the pilot plant results presented in numerous reports under DOE Contract DE-AC01-79ET10104 for operation of the pilot plants, and to relate these results to specific Demonstration Plant uncertainties. The ...

British Library Electronic Table of Contents (United Kingdom)

A series of thiazolo[3,2-b][1,2,4]triazole incorporating diphenylsulfone moieties were synthesized starting from 5-[4-(4-X-phenylsulfonyl)phenyl]-4H-1,2,4-triazole-3-thioles 3a-c, X=H, Cl, Br. Thus, alkylation of 1,2,4-triazoles 3 with phenacyl bromide or 4-bromophenacyl bromide afforded S-substituted 1,2,4-triazoles 4, 5. These new intermediates 4 and 5, in the presence of H2SO4 (c), were cyclized to 2-[4-(4-X-phenylsulfonyl)phenyl]-6-(4-Y-phenyl)[1,3]thiazolo[3,2-b]-[1, 2,4]-triazoles 6, 7 (I) and not to isomeric thiazolo[2,3-c][1,2,4]-triazoles 6, 7 (II). The newly synthesized compounds were characterized by IR, 1H, 13C NMR and elemental analysis. MS spectra confirmed the formation of thiazolo[3,2-b][1,2,4]triazole 6, 7 (forms I) in detriment of [2,3-c] isomeric compounds (forms II). Th...

Energy Technology Data Exchange (ETDEWEB)

The project has been developing Yttria Stabilized Zirconia (YSZ)-Alumina Composites as an electrolyte of a self-support type planar Solid Oxide Fuel Cell (SOFC) from the following points of view: a path of alumina particles with high thermal conductivity can be designed as an electrolyte sheet; there are some possibilities that the electrolyte can be enhanced in mechanical strength. As previously reported, these composite materials have higher mechanical strength and better thermal shock resistance than those of YSZ. These composites containing 0-30 wt% of Al[sub 2]O[sub 3] were measured by AC impedance method at temperatures of 250-1,000[degree]C. Electrical conductivities of 8YSZ without Al[sub 2]O[sub 3] and a composite consisting of 80 wt% YSZ and 20 wt%Al[sub 2]O[sub 3] as sintered samples were 1.2 x 10[sup -1]S/cm and 1.0 x 10[sup -1]S/cm respectively at 1,000[degree]C. The composite containing 20 wt% of Al[sub 2]O[sub 3] is the most promising candidate ...

Energy Technology Data Exchange (ETDEWEB)

Adsorptive removal of Pb(II) ions from aqueous solution onto a non-activated charcoal (CC) of oak wood origin was studied in comparison with an activated carbon of coal origin. The adsorption capacity for Pb(II) of the non-activated charcoal increased significantly with deceasing particle diameter, whereas the activated carbon (AC) exhibited approximately constant capacity for Pb(II) adsorption as a function of particle size. Adsorption to the ashes prepared from the non-activated charcoal and the activated carbon was also investigated to examine the role of mineral ash. Although the ash from the activated carbon did not show any Pb(II) adsorption, the ash from the charcoal was very effective for Pb(II) adsorption. Furthermore, Pb(II) was hardly adsorbed when the ash was removed from the non-activated charcoal by acid treatment. Based on the results, the adsorption sites for Pb(II) are considered to be acidic surface functional groups on the external and internal ...

International Nuclear Information System (INIS)

In developing new brain imaging agents for single photon emission computed tomography (SPECT), we synthesized eleven radioiodinated phenoxyacetic acid derivatives and investigated the relationship between the chemical structure and in vivo characteristics. Biodistribution studies in mice revealed high initial brain uptake for all the compounds. Blood radioactivity level depended markedly upon the chemical stability of the compound. The #alpha#,#alpha#-dimethylester derivative (1e), amide derivatives (2a-c) and diamine derivatives (3a, b, 4), which were stable to hydrolysis, showed low blood activity levels following i.v. administration. Disappearance of the ester and amide compounds from the brain was rapid. However, the diamine derivatives displayed improved retention in the brain. Compounds 3a and 4 possessed the best combination of high brain uptake and sufficient retention to be useful as potential brain imaging radiopharmaceuticals with SPECT devices. ...

International Nuclear Information System (INIS)

Li_1_._3Al_0_._3Ti_1_._7(PO_4)_3 thin films were successfully prepared by the solution deposition using lithium acetate, aluminum nitrate, ammonium dihydrogen phosphate and titanium butoxide as starting materials. The structure, surface morphology, electrochemical window, and ionic conductivity of the films were studied by X-ray diffraction, scanning electron microscopy, cyclic voltammetry and AC impedance. The results showed that Li_1_._3Al_0_._3Ti_1_._7(PO_4)_3 thin films annealed between 750 deg. C and 900 deg. C prepared by this method were well crystallized, homogenous and crack-free. The electrochemical window was beyond 2.4 V and the ionic conductivity was approximately 1.57x10"-"5 S/cm at room temperature for the film annealed at 800 deg. C for 30 min.

Energy Technology Data Exchange (ETDEWEB)

This final report summarizes the results of our research under Contract No. DE-AC22-92PC92112, Novel Catalysts for Methane Activation. In this research we prepared and tested fullerene soots for converting methane into higher hydrocarbons. We conducted the methane conversions using dehydrocoupling conditions, primarily in the temperature regimes of 600{degrees}-1000{degrees}C and atmospheric pressures. The research was divided into three sections. The first section focused on comparing fullerene soots with other forms of carbon such as acetylene black and Norit-A. We found that the fullerene soot was indeed more reactive than the other forms of carbon. However, due to its high reactivity, it was not selective. The second section focused on the effect of metals on the reactivity of the soots, including both transition metals and alkali metals. We found that potassium could enhance the selectivities of fullerene soot to higher hydrocarbons, but the effect was unique ...

Energy Technology Data Exchange (ETDEWEB)

Since 1958, the AlliedSignal Federal Manufacturing and Technologies (FM and T) Metrology Department has developed measurement technology and calibration capability in four major areas of measurement: mechanical; environmental, gas, liquid; electrical (D.C., A.C., RF/microwave); and optical and radiation. The capabilities developed include unique capabilities in many areas of measurement and engineering expertise to develop measurement techniques and resolve measurement problems in these major areas. FM and T Metrology was established in 1958 to provide a measurement base for the Department of energy`s Kansas City Plant. The Metrology Engineering Department provides the expertise to develop measurement capabilities for virtually any type of measurement which falls into the broad areas listed above. The engineering staff currently averages almost 16 years of measurement experience. A strong audit function has been developed to provide a means to evaluate the ...

International Nuclear Information System (INIS)

The AC susceptibility of La_xNd_1_-_xF_3 single crystals, for 0#<=#x#<=#0.1, has been measured from 1.5 up to 40 K and their DC susceptibility for 0#<=#x#<=#1 has been measured from 3 up to 300 K in magnetic fields up to 0.2 T. In both susceptibilities the magnetic fields were applied parallel to the crystallographic a-axis (perpendicular to the c-axis). The effective Bohr magneton number p_e_f_f and paramagnetic Curie temperature #theta#_p have been obtained, using the Curie-Weiss law in the temperature range 100-300 K. Also the g-values corresponding to the five Kramers doublets in the "4I_9_/_2 ground multiplet of Nd"3"+ ion in La_xNd_1_-_xF_3 have been determined in the direction perpendicular to the c-axis, using the Van Vleck theory of paramagnetic susceptibility. The effect of the dilution of the paramagnetic Nd"3"+ ions with diamagnetic La"3"+ ions is also discussed. (orig.).

Energy Technology Data Exchange (ETDEWEB)

We have simulated the transient enhanced diffusion (TED) of boron fluoride (BF{sub 2}{sup +}) implanted in crystalline and germanium amorphized silicon. Based on recently published models, the effect of fluorine on boron diffusion in silicon has been introduced and a modelling has been suggested. In order to simulate the boron experimental profiles, we have assumed that fluorine forms clusters involving interstitial boron which reduces the junction depth. Experimental results indicate that fluorine behaviour depends on amorphization energy. Moreover, even no germanium preamorphization is performed, silicon is still amorphized by fluorine species. Hence, BF{sub 2}{sup +} implantation leads to an amorphous/crystalline (a/c) interface near the surface. An improvement of published models is suggested taking into account fluorine effects. The simulations satisfactory reproduce the SIMS experimental profiles for a large scale of experimental conditions.

Energy Technology Data Exchange (ETDEWEB)

The objective of this work was to investigate the efficiency of imidazole derivatives for corrosion inhibition of copper in 0.5 M hydrochloric acid. Corrosion inhibition was studied using impedance spectroscopy. Imidazole and its derivatives 4-methylimida-zole, 4-methyl-5-hydroxymethylimidazole, 1-phenyl-4-methylimidazole, 1-(p-tolyl)-4-methylimidazole were investigated. These studies have shown that 1-(p-tolyl)-4-methylimidazole is the best inhibitor in this series and that it acts as mixed inhibitor. The nature of the chemical interaction between these molecules and the copper surface was investigated by Cu exposed to solutions having two very different pH values: 0.5 M HCl and unbuffered purified water. X-ray photoelectron spectroscopy and secondary ion mass spectrometry were used to explore the nature of the interaction. Possible mechanisms of corrosion inhibition for these molecules are discussed.

Energy Technology Data Exchange (ETDEWEB)

This report describes the design of an on-board battery charger for an electric car. There are already various battery charger units on the market. However, these are not specifically designed for this application, and consequently do not provide an ideal solution. Because these products are not specific to one application, and instead opt to cover a variety of briefs, they are not ideal. They also tend to be heavier and more expensive than if the charger was built specifically for one purpose. The main design considerations were that the charger should be compact and lightweight. It was also specified that the design should be able to operate using either the single-phase or three-phase AC supply. Before the design process for the battery charger could commence, it was necessary for the author to get an appreciation of power electronics, since he had no previous experience in the subject. The author focused his attention on areas of the subject most valuable to ...

International Nuclear Information System (INIS)

In this study, perovskite type oxide YAlO_3 has been doped with different amounts of the divalent cation Ca to synthesize Y_1_-_xCa_xAlO_3_-_#delta# (x = 0-0.21) compositions. The effect of dopant concentration on the crystal structure and electrical properties of YAlO_3 synthesized by citrate gel route has been investigated. The phase purity of the samples has been carried out using X-ray diffraction. The microstructural evaluation of the samples has been conducted by scanning electron microscopy and energy dispersive spectrum analysis. Thermal analysis has been conducted to monitor the decomposition of the intermediate products. The electrical conductivity studies have been performed using a.c. impedance spectroscopy as a function of temperature in the range 200-800 "oC in air. The Y_0_._9_4Ca_0_._0_6AlO_3_-_#delta# composition exhibits a total conductivity of 2.5 mS/cm at 800 "oC.

International Nuclear Information System (INIS)

This report is in accordance with Phase I of the United States Department of Energy and Bureau of Mines Contract No. USDOE DE-AC01-77QQ90147. A thorough literature search was conducted and the current mining practice at nine coal stripping operations reviewed in detail. A review of the state of the art of blast design using current theory and practice is presented. Based upon this information, a series of recommendations are presented and a detailed test program is outlined for three operations. The recommendations to increase dragline productivity by improved blast design are directed at filling the bucket more quickly, with greater consistency and with a better fill factor: (a) overburden fragmentation, (b) muckpile displacements, and (c) blasting reliability. Recommended blast design concepts and operating procedures to provide the desired blast performance include: (1) Increase energy input per BCY by 40 to 100 percent and improve the effective powder ...

Energy Technology Data Exchange (ETDEWEB)

Chromium containing amorphous hydrogenated carbon films (a-C : H/Cr) have been prepared by simultaneous rf plasma activated chemical vapour deposition of methane and magnetron sputtering of a chromium target. During deposition the substrates were heated (up to 300C) and DC biased (-200 and -600 V) in order to obtain films with high chemical stability. Constant temperature tests were performed at 250C in air with coatings deposited on silicon substrates. The degradation of the coatings was monitored by Raman spectroscopy and reflectance and transmission measurements. The main degradation mechanisms are discussed and the relevant parameters which improve the durability of the coatings are presented. Furthermore, the durability of solar selective, multilayered coatings which were deposited on copper sheets was investigated. Based on accelerated aging tests at different temperature loads in air (at 220C, 250C and 300C) and in a humid environment (80C sample temperature ...

DEFF Research Database (Denmark)

This paper presents a new grid connected inverter for fuel cells. It consists of a two stage power conversion topology. Since the fuel cell operates with a low voltage in a wide voltage range (25 V-45 V) this volt- age must be transformed to around 350-400 V in order to invert this dc power into ac power to the grid. The proposed converter consists of an isolated dc-dc converter cascaded with a single phase H-bridge inverter. The dc-dc converter is a current-fed push-pull converter. A new dedicated voltage mode startup procedure has been developed in order to limit the inrush current during startup. The inverter is controlled as a power factor controller with resistor emulation.Experimental results of converter efficiency, grid performance and fuel cell response are shown for a 1 kW prototype. The proposed converter exhibits a high efficiency in a wide power range (higher than 92%) and the inverter operates with a near unity power factor and a low current THD.

Science.gov (United States)

Language: English ...

International Nuclear Information System (INIS)

An outline of the instrumentation and control systems associated with fuelling machines is given. The control systems such as hydraulic system, oil hydraulic system, electric control system and the remote control systems have been discussed in detail. The difference between RAPP and MAPP fuel handling control systems has been explained. A computer based system for the Narora fuel handling control system is also discussed. (S.K.K.).

Energy Technology Data Exchange (ETDEWEB)

1. In order to carry out isothermic crystal growth experiments of YBCO the 123 primary crystallization field was determined by means of phase diagram investigations and crystal growth experiments at different oxygen partial pressure. 2. YBCO single crystals of high crystallographic perfection were grown and conclusions on the flux pinning mechanism were drawn. 3. By means of Liquid Phase Epitaxy (LPE) single crystalline (Tc{approx}90 K; {Delta}T{<=}0.5 K) c- and a,b- YBCO fils have been prepared on NdGaO{sub 3} and LaGaO{sub 3} substrates. The films were characterized structurally and magnetically. 4. Our fist melt textured YBCO ``single crystals`` possess intracrystalline critical current densities >10{sup 4} A/cm{sup 2} at B{<=}2T. The irreversibility inductions are {<=}6 T at 77 K. A simple demonstrator was constructed together with the IFW Dresden and a growth model was developed. 5. Using above all torque magnetometer measurements we separated intrinsic pinning effects ...

CERN Document Server

Randomized Algorithms for Analysis and Control of Uncertain Systems

Science.gov (United States)

vibration Isolation system for the camera. ... to further define the response of the camera vibration isolation system. These ...

Science.gov (United States)

The Java Mission Evaluation Workstation System (JMEWS) is a collection of applications designed to

KoreaScience (Korea)

Full Text Available

CERN Document Server

Beam Diagnostic System for High Intensity Proton Linac at KAERI

Energy Technology Data Exchange (ETDEWEB)

Three kinds of surface modifications were carried out on LiNi{sub 1/2}Mn{sub 3/2}O{sub 4} thin-films to improve the charge and discharge characteristics of LiNi{sub 1/2}Mn{sub 3/2}O{sub 4} positive electrodes. Among them, Zr(OBu){sub 4}/poly(methyl methacrylate) (PMMA)-treated LiNi{sub 1/2}Mn{sub 3/2}O{sub 4} thin-film electrodes showed charge and discharge efficiency of 80-84% in the first cycle, which was much higher than that for an untreated LiNi{sub 1/2}Mn{sub 3/2}O{sub 4} thin-film electrode (73%). The values of the charge and discharge efficiency were still higher than that for an untreated electrode after the 30th cycle. The charge and discharge curves gave two plateaus at around 4.72 and 4.76 V, which were very similar to those for the untreated electrode. Ac impedance spectroscopy revealed that the surface film resistance should not increase by Zr(OBu){sub 4}/PMMA treatment. XPS measurements suggest that a composite layer should be formed on a LiNi{sub ...

International Nuclear Information System (INIS)

Amorphization and a dual implant technique have been used to manipulate residual defects that persist following implantation and post-implant thermal treatments. Residual defects can often be attributed to ion-induced defect excesses. A defect is considered to be excess when it occurs in a localized region at a concentration greater than its complement. Sources of excess defects include spatially separated Frenkel pairs, excess interstitials resulting from the implanted atoms, and sputtering. Preamorphizing prior to dopant implantation has been proposed to eliminate dopant broadening due to ion channeling as well as dopant diffusion during subsequent annealing. However, transient-enhanced diffusion (TED) of implanted boron has been observed in pre-amorphized Si. The defects driving this enhanced boron diffusion are thought to be the extended interstitial-type defects that form below the amorphous-crystalline interface during implantation. A dual implantation process was applied in an ...

Energy Technology Data Exchange (ETDEWEB)

The Maybell uranium mill tailings site is 25 miles (mi) (40 kilometers [km]) west of the town of Craig, Colorado, in Moffat County, in the northwestern part of the state. The unincorporated town of Maybell is 5 road mi (8 km) southwest of the site. The designated site covers approximately 110 acres (ac) (45 hectares [ha]) and consists of a concave-shaped tailings pile and rubble from the demolition of the mill buildings buried in the former mill area. Contaminated materials at the Maybell processing site include the tailings pile, which has an average depth of 20 feet (ft) (6 meters [m]) and contains 2.8 million cubic yards (yd{sup 3}) (2.1 million cubic meters [m{sup 3}]) of tailings. The former mill processing area is on the north side of the site and contains 20,000 yd{sup 3} (15,000 m{sup 3}) of contaminated demolition debris. Off-pile contamination is present and includes areas adjacent to the tailings pile, as well as contamination dispersed by wind and ...

Energy Technology Data Exchange (ETDEWEB)

This document deals with the couplings between the W boson and Z and gamma particles. WWZ and WW{gamma} vertex are predicted by the electroweak theory based on the symmetry group SU(2){sub L}*U(1){sub Y}, their existence is confirmed by the measurement of the production cross-section of W pairs at LEP. The effective values of the couplings are modified by the introduction of standard model particle loops at the vertex level, the impact on the coupling value is assessed to reach 10{sup -3}. These loops can also include beyond-the-standard-model particles, their impact is in the magnitude order of 10{sup -3} for most models. The fully description of these loops requires the values of 14 complex parameters whose measurement will give information about the existence of new particles. Nevertheless the number of events at LEP is not sufficient to measure all the parameters simultaneously. As a consequence the analysis is limited to the 3 most promising parameters: g{sub 1}{sup Z}, ...

Energy Technology Data Exchange (ETDEWEB)

Horizontal vibrations of elevator cars mainly occur because a car swings as roller guides installed at corners of a car frame move on a winding guide rail at high speeds. Rider comfort in high speed elevators is worsened by these vibrations. Conventional active dampers suppressing horizontal vibrations using ac servo motors make cars heavier so driving power becomes larger, and they are not easily applied to existing elevators. An active damping control method suited to super-high-speed elevators is which can solve these problems. The method suppresses vibrations by generating only enough magnetic force needed to suppress them only when vibrations of the car franc are produced. The vibrations are detected using acceleration detectors and magnets installed on left and right sides of the car frame. A computer simulator was made to analyze phenomena of car vibrations and to verify effects of the proposed magnetic damping controller. It was found that the vibrations ...

Science.gov (United States)

There are many methods for introducing random mutations into nucleic acid sequences. Previously, we described a suite of programmes for estimating the completeness and diversity of randomized DNA libraries generated by a number of these protocols. Our programmes suggested some empirical guidelines for library design; however, no information was provided regarding library diversity at the protein (rather than DNA) level. We have now updated our web server, enabling analysis of translated libraries constructed by site-saturation mutagenesis and error-prone PCR (epPCR). We introduce GLUE-Including Translation (GLUE-IT), which finds the expected amino acid completeness of libraries in which up to six codons have been independently varied (according to any user-specified randomization scheme). We provide two tools for assisting with experimental design: CodonCalculator, for assessing amino acids corresponding to given randomized codons; and AA-Calculator, for finding degenerate codons that ...

Energy Technology Data Exchange (ETDEWEB)

The fixed bed pilot plant, the catalyst testing procedure, and the calculations for conversion and selectivities were previously described in the technical progress report covering the period of 3/16/88 to 6/16/88 for Contract DE-AC22-87PC79812. Conversions and hydrocarbon selectivities were calculated using data from an on-line gas chromatography (GC) analyzer. Alcohol selectivities were calculated using data from an on-line boiling point GC analyzer which analyzed the liquid product. The catalysts were prepared via the steps of impregnation, calcination, and reduction on a special Y-zeolite-derived support. The impregnation step consisted of evaporation of metal salts on to the support from an aqueous solution. For one catalyst (No. 6531-188) the metal salts were evaporated on to the support from a reverse micelle solution containing the metal salts. All the catalysts were calcined for four hours at 450{degree}C. The calcined catalysts were loaded in the reactor ...

Energy Technology Data Exchange (ETDEWEB)

The influence of substrate temperature on both the implantation and post-annealing characteristics of molecular-ion-implanted 5 x 10{sup 14} cm{sup -2} 77 keV BSi in silicon was investigated in terms of boron depth profiles and damage microstructures. The substrate temperatures under investigation consisted of room temperature (RT) and liquid nitrogen temperature (LT). Post-annealing treatments were performed using rapid thermal annealing (RTA) at 1050 deg, C for 25 s. Boron depth profiles and damage microstructures in both the as-implanted and as-annealed specimens were determined using secondary ion mass spectrometry (SIMS) and transmission electron microscopy (TEM), respectively. The as-implanted results revealed that, compared to the RT specimen, the LT specimen yields a shallower boron depth profile with a reduced tail into the bulk. An amorphous layer containing a smooth amorphous-to-crystalline (a/c) interface is evident in the LT specimen while just the ...

DEFF Research Database (Denmark)

Mutations in the FGD1 gene have been shown to cause Aarskog-Scott syndrome (AAS), or facio-digito-genital dysplasia (OMIM#305400), an X-linked disorder characterized by distinctive genital and skeletal developmental abnormalities with a broad spectrum of clinical phenotypes. To date, 20 distinct mutations have been reported, but little phenotypic data are available on patients with molecularly confirmed AAS. In the present study, we report on our experience of screening for mutations in the FGD1 gene in a cohort of 60 European patients with a clinically suspected diagnosis of AAS. We identified nine novel mutations in 11 patients (detection rate of 18.33%), including three missense mutations (p.R402Q; p.S558W; p.K748E), four truncating mutations (p.Y530X; p.R656X; c.806delC; c.1620delC), one in-frame deletion (c.2020_2022delGAG) and the first reported splice site mutation (c.1935+3A>C). A recurrent mutation (p.R656X) was detected in three independent families. ...

Science.gov (United States)

Aug 3, 2011 ... System (NASS) and the NERVA Effluent Purification System ... Effluent Purification System (NEPS). 7.4.2.2. Requirements ...

International Nuclear Information System (INIS)

The activities and the policy in the Netherlands regarding the development of the title systems since 1990 are briefly outlined, focusing on the use of PV-systems in buildings. 5 figs., 1 tab.

UK PubMed Central (United Kingdom)

The development of online communication systems related to prevention, decision making, and coping with cancer has outpaced theoretical attention to the attributes that appeal to system...Full Text Available

Wastenet

...Systems by IPEX Enfield electrofusion acid waste systems give you the proven corrosion resistance of polypropylene, along with our patented, state-of-the-art electrofusion system....

DEFF Research Database (Denmark)

Udgivelsesdato: JUL

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Norwegian Open Research Archives (NORA)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

This paper details the ongoing collaboration between the U.S. EPA and the U.S. Army Corps of Engineers in the development of complementary micro-computer based cost estimating systems for hazardous waste remediations. he U.S. EPA system, "Remedial Action Cost Estimating System" (...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... The seven existing space/airborne programs are the Defense Satellite Com- munications System (DSCS), Milstar, communications re- lay ...

Science.gov (United States)

Sunflower power conversion system development test program

International Nuclear Information System (INIS)

The main trends of research carried out in remote handling systems in the fields of ergonomy, robotics and reliability are presented.

CERN Document Server

Overview on some functional issues related to the uninterrupible power systems design

Energy Technology Data Exchange (ETDEWEB)

MINEQL is a subroutine package to calculate equilibrium composition of an aqueous system, accounting for mass transfer.

Science.gov (United States)

... They comprise of a power model for the representation of the electric system, a fluid model that represents the cooling fluid flow, three layers of ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

I discuss some recent developments in chiral effective field theory for few-nucleon systems.

Science.gov (United States)

... Hydropower analysis may include run-of-river, peaking, and pumped storage plants as well as system power operation. ...

Energy Technology Data Exchange (ETDEWEB)

The waste monitoring system in use at Los Alamos National Laboratory`s Plutonium Facility, TA-55, is a computer-based system that proves real-time information on industrial effluents. Remote computers monitor discharge events and data moves from one system to another via a local area network. This report describes the history, system design, summary, instrumentation list, displays, trending screens, and layout of the waste monitoring system.

Energy Technology Data Exchange (ETDEWEB)

A micro-computer based fuzzy logic power system stabilizer is applied to a micro-machine system to investigate its efficiency in real time control. The stabilizing signal is determined by using measured speed or real power signals at every sampling time to damp the system oscillations. The results show the proposed stabilizer improves the system damping effectively subject to various types of disturbances.

Energy Technology Data Exchange (ETDEWEB)

The paper presents a sequential procedure for coordinated stabilization of a multimachine power system with arbitrary complexity of the system model. The most effective machine to be equipped with a power system stabilizer is identified using eigenvalue analysis. The selection is based on the sensitivity of critical eigenvalues to increases in the coefficient of a damping term which is inserted in each equation of motion, in succession. The method is applied to a three-machine system and simulation studies show appreciable improvements in the small disturbance stability of the system.

Energy Technology Data Exchange (ETDEWEB)

An integrated voltage regulator and power system stabilizer based on one step ahead prediction is presented. The fixed parameter predictive control scheme is shown capable of providing consistently good voltage response and contribution to system damping over a wide range of operating conditions and system configuration. This is in contrast to the case with conventional automatic voltage regulator and power system stabilizer where performance varies widely with the operating situation and can even cause system instability. (author)

Energy Technology Data Exchange (ETDEWEB)

Daylight responsive dimming systems have been used in few buildings to date because they require improvements to improve reliability. The key underlying factor contributing to poor performance is the variability of the ratio of the photosensor signal to daylight workplane illuminance in accordance with sun position, sky condition, and fenestration condition. Therefore, this paper describes the integrated systems between automated roller shade systems and daylight responsive dimming systems with an improved closed-loop proportional control algorithm, and the relative performance of the integrated systems and single systems. The concept of the improved closed-loop proportional control algorithm for the integrated systems is to predict the varying correlation of photosensor signal to daylight workplane illuminance according to roller shade ...

Science.gov (United States)

We describe the Hubble Space Telescope (HST) Wide Field Camera 3 (WFC3) Early Release Science (ERS) observations in the GOODS-South field. The new WFC3 ERS data provide calibrated, drizzled mosaics with FHWM=0.07--0.15" in the near-UV (filters F225W, F275W, and F336W) and near-IR (F098W, F125W, and F160W) in typically 2 orbits per filter. Together with the existing HST/ACS GOODS-S mosaics in the BVi'z' filters, the 10-band ERS data cover 40-50 sq. arcmin to AB=26-27.0 mag (10-sigma for point sources). In this poster, we describe the: (1) scientific rationale, data taking and reduction procedures of the WFC3 ERS mosaics; (2) object cataloging and star-galaxy separation techniques used in these 10 different filters; (3) reliability and completeness of the 10-band object catalogs from the ERS mosaics; (4) object counts in 10 different filters from 0.2-1.7 microns to AB=26.0-27.0 mag; and (5) the full-color 10-band ERS images. We discuss the panchromatic structure ...

International Nuclear Information System (INIS)

This paper presents case studies of economic feasibility of solar photovoltaic systems using the software AVES-F (Analysis of Economic Feasibility of Photovoltaic Systems), developed by the authors, considering cases of stand-alone and grid-connected systems. The software takes into account several factors that can influence the economic feasibility of these kind of systems, like load to be supplied, distance to the grid, the use regime of the system, applied subsidies and others. The main goal of this paper is to analyze some of these factors and to observe how they can affect the economics of PV systems for electricity generation. (authors)

British Library Electronic Table of Contents (United Kingdom)

The term biological motion is often used by researchers studying the patterns of movement generated by living forms and in sports. We studied a pattern recognition system of motion in sport using biological motion data. Biological motion data are acquired using a 3D motion capture system. However, 3D motion capture systems are very expensive. In this article, a biological motion capture system was built using acceleration sensors. Our proposed system uses the technique of Gaussian fitting and regression analysis. We tested our proposed system in pattern recognition of outdoor tennis and its evaluations.

Energy Technology Data Exchange (ETDEWEB)

This guide is intended to provide the necessary guidance to successfully manage the NAVMED Navy Occupational Health Information Management System (NOHIMS) at NAVMED sites and the NAVSEA Occupational Safety and Health Record Keeping System (OSHRKS) at NAVSEA sites. Outlines procedures to manage system operations, procedures to resolve hardware, software and communications problems, and procedures outside the realm of system operations that are required for a successful system. This guide is intended for the System and Functional Managers use. The System Manager is the individual designated to provide overall ADP management to the entire local configuration. Usually responsible for file backup, daily operations of the CPU, security, supplies, equipment, operating software and technical ADP guidance to the local functional users.

International Nuclear Information System (INIS)

The Reliability Data Management System (RDMS) for safety systems of PHWR type plants has been developed and utilized in the reliability analysis of the special safety systems of Wolsong Unit 1 with plant overhaul period lengthened. The RDMS is developed for the periodic efficient reliability analysis of the safety systems of Wolsong Unit 1. In addition, this system provides the function of analyzing the effects on safety system unavailability if the test period of a test procedure changes as well as the function of optimizing the test periods of safety-related test procedures. The RDMS can be utilized in handling the requests of the regulatory institute actively with regard to the reliability validation of safety systems.

Energy Technology Data Exchange (ETDEWEB)

A novel adaptive stabilizer, called an Adaptive Governor Power System Stabilizer (AGPSS), which operated on the governor turbine system, was described. There has been extensive research on adaptive excitation control of generators in power systems with the goal of achieving better dynamic performance. AGPSS tracks the frequency and damping of oscillations in a power system, and adjusts to ensure that there is always sufficient damping in the system. There is no interaction between stabilizers on different generating units, and each one acts independently, consuming oscillation energy locally. These stabilizers are easy to design and this facilitates their use in multimachine systems. Results obtained by nonlinear simulation of a single-machine and a three-machine power system were discussed, illustrating the effectiveness of the stabilizers ...

Energy Technology Data Exchange (ETDEWEB)

A decoupled characteristic between the damping of a specific swing mode and the stabilizer gain of the corresponding machine in multimachine power systems is identified. Using this decoupled characteristic a power system stabilizer (PSS) synthesis approach which is based on the phase compensation concept is verified on a 9-machine system and the dynamic performance of this system is significantly improved. This method is proved to be effective, simple and it can provide useful guidance for the PSS field tuning.

Energy Technology Data Exchange (ETDEWEB)

A semi-automatic system which considers operation in a face by monitoring technological parameters of an extraction vehicle and a longwall conveyor is examined. The system records in tabular form the location, progress made, operating and down time of an extraction vehicle and operating and down time of the conveyor. A description of the operating principle system and systems for arrangement of the remote sensing and central recording device are presented. (Note: extraction vehicle not identified: LTN)

International Nuclear Information System (INIS)

This book contains the proceedings of the International Topical Meeting on Remote Systems and Robotics in Hostile Environments. It is organized under the following sessions: Worldwide Applications Overview; Operating Mobile Systems; Sensors and Control Systems; Space Applications; Reactor Operations and Surveillance; Remote Equipment for Hazardous Operations; Future Mobile System; Mining and Construction Operations; Special Applications; Hot Cell Applications; Processing; Reactor Operations and Maintenance; Decontamination and Waste Handling; Remote Handling Development and Demonstration.

Energy Technology Data Exchange (ETDEWEB)

The basic design of a system installed in the Columbus, Ohio Zoo is described. The distribution system is described in detail. The control system is microprocessor controlled, with about 50 monitoring points. Preliminary evaluations have indicated that the system can operate with an overall coefficient of performance in excess of 3.5. 1 figure.

Energy Technology Data Exchange (ETDEWEB)

The purpose of this paper is to describe instrumentation and control (I&C) system improvements at Experimental Breeder Reactor 11 (EBR-11). The improvements are focused on three objectives; to keep the reactor and balance of plant (BOP) I&C systems at a high level of reliability, to provide diagnostic systems that can provide accurate information needed for analysis of fuel performance, and to provide systems that will be prototypic of I&C systems of the next generation of liquid metal reactor (LMR) plants.

Energy Technology Data Exchange (ETDEWEB)

The purpose of this paper is to describe the embedded computer systems approach taken at Experimental Breeder Reactor II (EBR-II) for non-safety related systems. The hardware and software structures for typical embedded systems are presented The embedded systems development process is described. Three examples are given which illustrate typical embedded computer applications in EBR-II.