UK PubMed Central (United Kingdom)

BackgroundAdolescents have been identified as a high-risk group for poor adherence to and defaulting from combination antiretroviral therapy (cART) care. However, data on outcomes...Full Text Available

UK PubMed Central (United Kingdom)

The objective of the present work was to formulate the enteric minitablets of isoniazid by cold extrusion method. The minitablets were prepared using isoniazid, hydroxylpropylmethylcellulose phthalate...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Following the breakthrough for cast magnesium products, interest is now spreading to wrought applications - triggering a variety of technological questions. A major bottleneck in the manufacture of magnesium sections (profiles) by conventional hot extrusion is the low productivity, with extrusion speeds typically five to ten times lower than for comparable aluminium sections. This paper focuses on the use of hydrostatic extrusion as a means to overcome this problem. On the basis of an analytical model, it is clarified why and how process limits are affected by the process mechanics. Experimental work on the hydrostatic extrusion of the alloys M1A, ZM21 and AZ31 confirms that extrusion speed is indeed multiplied, whereas the resulting mechanical properties are similar to or better than those for conventional extrusions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Magnesium cast parts as well as indirectly and hydrostatically extruded profiles were used in order to investigate the influence of different microstructures on the damping behaviour of magnesium AZ-alloys. Especially, hydrostatic extrusion leads to a significant grain refinement in the extruded profile compared to indirect extrusion. Strain dependent damping measurements were carried out at room temperature using alloys AZ31, AZ61 and AZ80. Damping was determined as the logarithmic decrement of free bending beam vibrations. The results of these measurements after indirect and hydrostatic extrusion are shown and discussed. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Two physical pre-treatment methods, particle size reduction by grinding and thermo-mechanical extrusion, were evaluated as alternatives to traditional biomass pretreatments for lignocellulosic ethanol. Commonly available agricultural co-products wheat bran and soybean hull were the model substrates. Extrusion led to higher reducing sugar yields as compared to grinding for wheat bran, but not in the case of soybean hulls. The best combination of extrusion screw speed and maximum barrel temperature were 7 Hz/150 ?C and 3.7 Hz/110 ?C. The use of a solvent mixture (sodium hydroxide, urea, and thiourea) and calcium chloride solution in combination with extrusion treatment did not lead to improvement in reducing sugar yield. However, extensive washing to get rid of solvents and enzymatic inhibit...

Science.gov (United States)

Development in organic farming has been stimulated by farmers and consumers becoming interested in healthy food products and sustainable environment. Organic agriculture is a holistic production management system which is based on the principles of health, ecology, care, and fairness. Organic development in Uganda has focused more on the crop sector than livestock sector and has primarily involved the private sector, like organic products export companies and non-governmental organizations. Agriculture in Uganda and many African countries is predominantly traditional, less mechanized, and is usually associated with minimum use of chemical fertilizers, pesticides, and drugs. This low external input agriculture also referred to as "organic by default" can create basis for organic farming where agroecological methods are introduced and present an alternative in terms of intensification to the current low-input/low-output systems. Traditional ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys and composites are potentially highly attractive materials for lightweight design in the automotive industry - if common forming technologies, i.e., deep drawing and cold extrusion, are applicable to them; so far, this is seldom the case. The authors have tested some candidate Mg alloys and discuss the results of their measurements in detail. The Figure shows a typical workpiece part obtained by a deep-drawing technique. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

In Uganda, biomass comprises more than 95 per cent of the total energy supply. Agricultural residues are a major source of energy that can be converted into producer gas in biomass gasifiers. The high poverty levels in Uganda can be attributed in part to the fact that more than 90 per cent of the population does not have access to electricity due to limited and unreliable electricity produced in the country. A circulating fluidized bed (CFB) gasification system was designed in this study in order to generate a system for the effective use of agricultural wastes for energy production. Rice husks were used as the feedstock for a power output of 60 MW. The gasification system was designed using ERGUN CFB software with available theoretical and experimental data. The design comprises a reactor subsystem, air distribution plate, cyclone, air inlet and fuel feeding systems. The reactor is 10 m high and has a fuel flow rate of 8.1 kg/s. The inlet air ...

Science.gov (United States)

Wood Plastic Composites (WPCs) have experienced a healthy growth during the last decade. However, improvement in properties is necessary to increase their utility for structural applications. The toughness of WPCs can be improved by creating a fine cellular structure while reducing the density. Extrusion processing is one of the most economical methods for profile formation. For our study, rectangular profiles were extruded using a twin-screw extrusion system with different grades of HDPE and with varying wood fibre and lubricant contents together with maleated polyethylene (MAPE) coupling agent to investigate their effects on WPC processing and mechanical properties. Work has been done to redesign the extrusion system setup to achieve smoother and stronger profiles. A guiding shaper, submerged in the water, has been designed to guide the material directly through water immediately after exiting the die; instead of passing ...

Energy Technology Data Exchange (ETDEWEB)

We have demonstrated that the SSSE pulverization process can convert multicomponent plastic waste into a powder with very promising properties. A variety of mixed color plastic chips have been pulverized.

UK PubMed Central (United Kingdom)

Tubular membrane structures are widespread in eukaryotic cells, but the mechanisms underlying their formation and stability are not well understood. Previous work has focused on tube extrusion from...Full Text Available

International Nuclear Information System (INIS)

One of the greatest opportunities for using of biomass as a precursor in the production of polymeric materials is the lignocellulose composites that can combine high performance with low costs. This work is a initial study on the production of a lignocellulose reinforced polyethylene composite. A compatibilization made by a induced gamma radiation grafting reaction was used to increase the adhesion between the matrix and the reinforced or filled fibers. The lignocellulose materials were exposed to gamma radiation in order to promote a molecular degradation and increase its reactivity. The polymer, the lignocellulose material and the compatibilization were processed by extrusion and the composite produced by this process were characterized by mechanical tests. (author)

British Library Electronic Table of Contents (United Kingdom)

Summary Objective Community-based information on the delivery and use of health interventions is important to monitor the effectiveness of the Roll Back Malaria programme. However, community surveys to determine coverage for insecticide-treated bed nets are time-consuming and costly. We wanted to assess whether schoolchildren's reports of household ownership of a bed net and coverage among high-risk groups monitored by schoolteachers through a questionnaire could be used as a proxy of household ownership of bed net and coverage at community level, for routine monitoring of malaria control programmes. Method 3602 schoolchildren in 39 randomly selected schools and 2798 heads of households in 39 villages were interviewed about their use of either insecticide-treated or untreated bed nets. Res...

Energy Technology Data Exchange (ETDEWEB)

Blow forming characteristics of 5083 Al alloy and AZ31 Mg alloy recycled by solid state recycling were investigated. Scraps with different volume were recycled by hot extrusion and hot rolling in air. Oxide layers, which were contaminants from scrap surface, were distributed parallel to the extrusion direction in the recycled specimens. In the blow-forming test, the specimen from smaller scraps exhibited lower formability. The oxygen concentration in the recycled specimens was approximately proportional to the total surface area of scraps in the recycled specimen per unit volume. The low formability of the recycled specimens is likely to be attributed to contamination level of oxide. (orig.)

International Nuclear Information System (INIS)

The feasibility of using a thermoplastic-powder metallurgy technique for the fabrication of porous niobium rods was investigated. Some early problems were overcome to successfully extrude the polymer coated niobium powder into long lengths. The effects of certain process variables were investigated. Residual porosity and extrusion pressure were found to be regulated by the polymer fraction. The procedures for taking the extruded polystyrene--niobium rods through the heat treatments to the final, tin infiltrated stage are explained.

Environmental Research Database

DescriptionDespite the growing recognition of the important part fruit and vegetables can play in helping prevent a number of diseases, health and nutrition experts are concerned about the low consumption of fruits and vegetables in the UK. The principal aim of this project is to improve consumer dietary consumption of fruit and vegetables by developing novel snack foods based on the fruit and vegetable materials using extrusion processing.

Energy Technology Data Exchange (ETDEWEB)

This quarterly report covers the period from January 1, 2005 through March 31, 2005. It covers: technical development, permitting status, engineering status, construction status, operations summary and marketing support activities for this period. Plant startup is still continuing. Testing of admixtures to enhance extrusion and SDA wetting is continuing. Efforts are underway to improve plant availability.

Energy Technology Data Exchange (ETDEWEB)

Solid recycling of AZ31 Mg alloy with vapor deposition coating layer of high purity Mg was evaluated. In the open die forging experiments, two AZ31 Mg alloy specimens with the pure Mg layer were sufficiently bonded by forging at 673 K. Furthermore, the Al and Zn of the AZ31 substrate diffused up to the center of the pure Mg layer. By the theoretical analysis, it is suggested that the grain boundary diffusion enhanced by grain refinement due to hot forging contributes to the solid state bonding of the specimens. Also, the solid recycled specimen was fabricated from the AZ31 Mg substrate with pure Mg layer by hot extrusion at 673 K. The solid recycled specimen showed almost the same tensile properties as the virgin extruded specimen. This is probably related not only to the grain boundary diffusion but also severe plastic deformation by hot extrusion. (orig.)

Energy Technology Data Exchange (ETDEWEB)

In order to enhance the mechanical properties of magnesium alloy (AZ31) sheet, an integrated sheet-making process including billet casting, extrusion and rolling was attempted. Microstructural analysis was carried out and the mechanical properties at each processing step were also investigated by tensile tests. By an extrusion process of ingot-processed billet, average grain size of billet was reduced from 91.2 to 28.2 {mu}m, and a further reduction in grain size to 16.9 {mu}m was obtained by subsequent rolling of extruded 5 mm thin slab. In the final step, a rolled sheet of 1 mm showed a remarkable refinement in grain size down to 8.8 {mu}m. Regarding mechanical properties, tensile strength and elongation for as-cast billet, as-extruded thin slab and as-rolled sheet increased from 189, 258 to 234 MPa, and from 13, 16.5 to 23%, respectively. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Inert gas contamination, structure and mechanical properties of consolidated high-Ni alloy powder material were studied to improve its characteristics. In experiment, the chemical composition and fraction of porosity in cross sections of Alloy 625 powder were examined which was produced by Ar gas atomization method impinging supplemental gas jet onto accumulated alloy powder in the bottom of a tank for rapid cooling. The structure and mechanical properties of the alloy rod were also examined which was produced by hot hydrostatic pressing or hot extrusion of the powder filled into a capsule. As a result, although Ar content included in the powder produced by Ar gas atomization method decreased with reduction in grain size, the fine powder less than 22{mu}m still included Ar of nearly 0.5mass-ppm. Obvious correlation was found between the fraction of porosity in powder cross sections and Ar in the powder. Although cavities were detected in the consolidated powder ...

Energy Technology Data Exchange (ETDEWEB)

The microstructure and mechanical properties of a specimen HIPped at 1100 C under 60 ksi were examined. The examinations indicated that the proper HIPping temperature for this material should be higher than 1100 C. New recipe of monolithic material was developed and presented better extrusion homogeneity and less binder removal defects. However, cracking still occurred in specimens although very slow heating rate of 0.25 C/min for binder burnout was used.

Energy Technology Data Exchange (ETDEWEB)

Airbag pressure vessels for the north-American market mainly are made by forging and by the use of steel alloys. In Europe aluminum alloys are common and the manufacturing process is extrusion of circular blanks - made from cold rolled plates - in a form applying a 100 t press at room temperature. Then by heat treatment the strength/hardness of the material is properly adjusted and after that the pressure vessel parts have to be continuously inspected with an inspection and handling cycle time of 3 s. Inspection of the axis-symmetric parts is asked for surface breaking extrusion defects as well as for surface parallel delaminations in the bulk volume. Furthermore, the material strength is a quality characteristic that has to be nondestructively registered and documented. The inspection is performed by eddy current probes and an EMAT, of which the eddy current impedance measurements are used for surface breaking extrusion ...

Energy Technology Data Exchange (ETDEWEB)

Two rapidly solidified powders with compositions Al-6.7 wt.% Fe-5.9 wt.% Ce and Al-6.2 wt.% Fe-5.9 wt.% Ce-1.63 wt.% Si were separated into -32 [mu]m and +32 to -63 [mu]m size fractions. Powders from both size fractions were extruded at 500 C. For comparison purposes, extrusion at a lower temperature of 400 C was also performed. In this investigation, tensile property evaluation indicated that processing of finer size fractions at high temperature offers no advantages in terms of the tensile properties but is advantageous in terms of improving the fracture toughness of alloy B. These observations underline the importance of the stability of powder microstructure during thermomechanical processing for the development of optimum mechanical properties. (orig.)

International Nuclear Information System (INIS)

Multifilamentary superconductors with 2.5 micron sized NbTi filaments are being proposed for the High Energy Booster part of the SSC project. The small filament size and the large number of filaments in the superconductor strands make the fabrication a challenge, especially in view of the high critical current performance required of them. IGC has produced two 309 mm diameter prototype billets and fabricated both the 'Inner' and the 'Outer' grade strands. The production approach was based on a triple extrusion process incorporating Cu-0.6 st.% Mn as the interfilament matrix material. The results of this pilot development effort, in terms of critical current density and mechanical properties, are presented in this paper. Appropriate comparisons with past performances are made.

International Nuclear Information System (INIS)

The proposed Superconducting Super Collider (SSC) in the US and plans for a Large Hadron Collider LHC at CERN are likely to require micron size filaments to reduce micron size filaments to reduce magnetization effects at the low injection fields envisioned. Superconductors of NbTi, designed to meet these requirements, are described. These conductors contain from 6000 to 36,613 filaments. Results are presented on NbTi conductors made by multiple extrusion techniques. Filament sizes of between 2.2 and 17 micron have been obtained. Current densities of between 2400 A/mm"2 and nearly 3400 A/mm"2 at 5 Tesla have been achieved. Metallurgical aspects of these conductors are presented using both optical and SEM views of conductor cross section and filament surface.

British Library Electronic Table of Contents (United Kingdom)

Abstract Introduction.- Sling erosion/extrusion is a complication after suburethral sling insertion for female stress urinary incontinence that occurs in approximately 6% of patients. Symptoms may include vaginal discharge, infections, postcoital bleeding, and alterations of the sexual function. Little is known about the effect of sling erosion on the sexual function of the male partner. Aim.- The aim of this study was to determine male sexual function in partners of women who had undergone sling insertion for stress urinary incontinence and who developed sling erosion postoperatively. Main Outcome Measures.- Main outcome measures were the Brief Male Sexual Function Inventory (BMSFI) and visual analog scale (VAS) scores. Methods.- Male partners of patients who presented with sling erosion ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys are ideal candidates to benefit from equal channel angular extrusion (ECAE) because of their poor forming characteristics due to a hcp structure. In this study, ECAE processing was applied to ZK31 and AZ31 magnesium alloys under various conditions. The grain size of as-ECAE specimens decreases with decreasing the processing temperature, however, the grain size decreases slightly with increasing number of repetitive processing. Both the tensile strength and 0.2% proof stress of as-ECAE specimens are high when processed at low temperature, but the elongation is high when processed at high temperature. Crystal orientation is different in the two alloys and it also varies according to the processing temperature for the two alloys. The difference of the crystal orientation influences the tensile properties, especially 0.2% proof stress. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Excellent mechanical properties and corrosion resistance combined with low weight qualify ?-titanium materials for lightweight applications in aviation, automotive and energy engineering. Thus far, actual applications of these materials have been limited due to high material costs and limited processing knowledge. One approach for developing resource-efficient manufacturing methods is the application of incremental forming methods. This article focuses on the development of the incremental spin extrusion process, which creates hollow profiles from solid bars. This method allows hollow shape manufacturing with a much higher flexibility than other forming methods and a significantly improved material utilization in comparison to machining methods, such as deep hole drilling. Beta-titanium al...

Energy Technology Data Exchange (ETDEWEB)

Recent developments on plastic forming technology of magnesium alloys are presented. Attempts have been undergoing with an aim at forming magnesium alloy parts at lower temperatures. It is believed that fine microstructure magnesium alloys usually have much higher plasticity at lower temperatures and even room temperatures. Extrusion is a method to form magnesium profile products and tube products, which is also one of the effective ways to make fine microstructure magnesium alloys. Superplasticity forming is another method to form high plasticity magnesium alloys. Hot forming of magnesium sheet parts is an important process to form magnesium products. Some developments related to above issues are discussed in the present paper. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is to develop an industrial process for the synthesis of an extrusible electrolyte polymer for lithium batteries. From literature data and precise specifications the high molar mass EO/OP copolymers synthesis by coordinative catalysis has been studied in order to reach a high productivity and to minimize the treatment steps. Two catalytic systems have been studied: the aluminium alkoxide-based Vandenberg-type catalysis and the calcium alcoholate amides catalysis. The first catalysis performed in solution gives excellent results. Its adaptation to silicon supported catalysis leads to a directly usable polymer in suspension but the productivity falls down and remains to be optimized. The calcium amide catalysis in heptane suspension generates acceptable productivities but also a too high proportion of low molar masses. Various approaches have been studied to minimize this proportion due to the presence of secondary sites that generate a cationic ...

Energy Technology Data Exchange (ETDEWEB)

A conceptual hydrodynamic model in the Holocene and upper Pleistocene beneath the Louisiana wetlands is described in terms of safety distributions. Porewater safety is calculated from electrical measurements, including resistivity soundings, electric logs, and electromagnetic profiling. Electrical measurements support the primary, basin-wide groundwater flow model; however, the data also indicate secondary contributions from expulsion of fluids under geopressure along active growth faults and from original waters of deposition. Expulsion of water from growth faults has been described previously for deeper sections of the Pleistocene, but has not been reported for the Holocene or upper Pleistocene beneath the Louisiana wetlands. Porewater chemistry variations beneath the coastal wetlands are a consequence of the following (in order of importance): (1) environment of deposition; (2) a basin-wide, regional flow system; (3) expulsion from deep-seated growth faults; and (4) pore water ...

Energy Technology Data Exchange (ETDEWEB)

This work deals with a new route to modify polymer blend morphology in order to improve the porosity of gas diffusion layers (GDLs) for proton exchange membrane fuel cells (PEMFCs). First, electrically conductive polymer-based blends were carefully formulated using a twin-screw extrusion process. Blend electrical conductivity was ensured by the addition of high specific surface area carbon black and synthetic graphite flakes. Final GDL porosity, in particular its macroporosity, was generated by melt blending polyamide 11 (PA11) matrix with polystyrene (PS) followed by PS extraction with tetrahydrofuran (THF) solvent at room temperature. In order to improve GDL porosity by the optimisation of PS dispersion in the PA11 matrix, PA11/PS blends were compatibilised by the addition of 2 wt.-% of clay. It was observed that both macroporosity and pore size distribution were beneficially modified after blend compatibilisation. Final GDL conductivity of about 1.25 S cm{sup ...

Energy Technology Data Exchange (ETDEWEB)

Feasibility of mushy state forming of magnesium alloys making use of resistance heating was examined. Magnesium alloys, AZ31, AZ61 and AZ91, were taken up as experimental materials and cylindrical billets with a diameter of 15 mm and a height of 20 mm were used for both resistance heating and forming experiments. Input heat control was applied to the billet heating and insertion of thin discs of austenitic stainless steel with a low thermal conductivity between the billet and copper electrodes was attempted in order to improve the efficiency of the billet heating. Results were summarized as follows. (1) Resistance heating by input heat control was successful to heat the billets to their respective mushy state. (2) Insertion of the discs was very helpful in heating the billets and realized the heating in a couple of seconds. (3) The force applied to the electrodes to ensure the electrical contacts being too small, sparks occurred and welds arose between the billets and discs. Contact ...

Energy Technology Data Exchange (ETDEWEB)

Clay-based materials can be cold-stabilized using binder and formed by extrusion. This paper deals with the properties of such materials under the influence of silico-aluminous flying ashes addition. Flying ashes are solid industrial wastes produced by coal combustion. Characteristics of ashes bearing clay-based products, such as dimensional stability, water and mechanical resistance, accelerated aging, are considerably improved with respect to simple clay-binder mixtures. This is principally due to a better hydration of the binder in ashes-bearing mixtures because of: a higher free-water availability as a consequence of the smaller specific surface of ash grains, the filler effect of ash grains which do not participate to the reactions, the specific property of silico-aluminous ashes that can fix the lime in presence of water to produce hydrated compounds. These ashes-bearing clay based materials can have the same qualities as classical building materials but ...

DEFF Research Database (Denmark)

We present an experimental study of vesicle fusion using light and neutron scattering to monitor fusion events. Vesicles are reproducibly formed with an extrusion procedure using an single amphiphile triethylene glycol mono-n-decyl ether in water. They show long-term stability for temperatures around 20 C, but at temperatures above 26 C we observe an increase in the scattered intensity due to fusion. The system is unusually well suited for the study of basic mechanisms of vesicle fusion. The vesicles are flexible with a bending rigidity of only a few k(H)T. The monolayer spontaneous curvature, Ho, depends strongly on temperature in a known way and is thus tunable. For temperatures where H-0 > 0 vesicles tyre long-term stable, while in the range H-0 < 0 the fusion rate increases the more negative the Spontaneous curvature Through a quantitative;analysis of the fusion rate we arrive tit a barrier to fusion changing from 15 k(B)T at T = 26 degrees C to 10k(H) T ...

Energy Technology Data Exchange (ETDEWEB)

As lithium battery technology sets out to bridge the gap between portable electronics and the electrical automotive industry, cathode materials still stand as the bottleneck regarding performances. In the realm of highly attractive polyanion-type structures as high-voltage cathode materials, the sulfate group (SO{sub 4}){sup 2-} possesses an acknowledged superiority over other contenders in terms of open circuit voltage arising from the inductive effect of strong covalent S-O bonds. In parallel, novel lithium insertion mechanisms are providing alternatives to traditional intercalation, enabling reversible multi-electron processes securing high capacities. Combining both of these advantageous features, we report here the successful electrochemical reactivity of copper sulfate pentahydrate (CuSO{sub 4}.5H{sub 2}O) with respect to lithium insertion via a two-electron displacement reaction entailing the extrusion of metallic copper at a dual voltage of 3.2 V and 2.7 V ...

Science.gov (United States)

Environmental arsenic is a world-wide health issue, making it imperative for us to understand mechanisms of metalloid uptake and detoxification. The predominant intracellular form is the highly mephitic arsenite, which is detoxified by removal from cytosol. What prevents arsenite toxicity as it diffuses through cytosol to efflux systems? Although intracellular copper is regulated by metallochaperones, no chaperones involved in conferring resistance to other metals have been identified. In this article, we report identification of an arsenic chaperone, ArsD, encoded by the arsRDABC operon of Escherichia coli. ArsD transfers trivalent metalloids to ArsA, the catalytic subunit of an As(III)/Sb(III) efflux pump. Interaction with ArsD increases the affinity of ArsA for arsenite, thus increasing its ATPase activity at lower concentrations of arsenite and enhancing the rate of arsenite extrusion. Cells are consequently resistant to environmental concentrations of arsenic. ...

International Nuclear Information System (INIS)

Textured silicon nitride (Si_3N_4) has been intensively studied over the past 15 years because of its use for achieving its superthermal and mechanical properties. In this review we present the fundamental aspects of the processing and anisotropic properties of textured Si_3N_4, with emphasis on the anisotropic and abnormal grain growth of #beta#-Si_3N_4, texture structure and texture analysis, processing methods and anisotropic properties. On the basis of the texturing mechanisms, the processing methods described in this article have been classified into two types: hot-working (HW) and templated grain growth (TGG). The HW method includes the hot-pressing, hot-forging and sinter-forging techniques, and the TGG method includes the cold-pressing, extrusion, tape-casting and strong magnetic field alignment techniques for #beta#-Si_3N_4 seed crystals. Each processing technique is thoroughly discussed in terms of theoretical models and experimental data, including the ...

Energy Technology Data Exchange (ETDEWEB)

Ophiolitic rocks occur as wall rocks of the 2.7 Ga Louis Lake batholith near Atlantic City, Wyoming. All of the Archean rocks are strongly deformed and metamorphosed to a greenschist and amphibolite facies, but relict structures and textures are commonly preserved. These include the following, from west to east: (1) metadiabase with rare coarse-grained metagabbro; (2) ultramafic rocks and metagabbro; (3) amphibolite, locally pillowed, overlain(.) by pelitic schist, banded iron formation, and quartzite; and (4) pillow lavas, massive sills or flows, and minor metasedimentary rocks. Slice 1 locally contains parallel dike margins and rare metagabbro screens; these features suggest that it may represent a sheeted dike complex. Slice 2 locally contains ultramafic rocks having relict cumulus textures and igneous layering, corresponding to the cumulus portion of an ophiolite. The pillow lavas of slice 4 and possibly slice 3 are interpreted as comprising the extrusive ...