J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Several of the issues of the workshop are addressed from the perspective of a potential Space Station developer and energy wheel user. Systems considerations are emphasized rather than component technology. The potential of energy storage wheel (ESW) concept is discussed. The current status of the technology base is described. Justification for advanced technology development is also discussed. The study concludes that energy storage in wheels is an attractive concept for immediate technology development and future Space Station application.

Science.gov (United States)

The patent application describes an anti-friction worm-wheel assembly wherein the anti-friction elements are rollers carried by the worm element. The rollers sequentially move through grooves in the edge surface of the wheel element to transmit drive forc...

Energy Technology Data Exchange (ETDEWEB)

Analyzed are methods for optimizing productivity of coal surface mining systems which consist of bucket wheel excavators, belt conveyors, and dumping conveyors. System productivity depends on adjustment of belt conveyor capacity to productivity of bucket wheel excavators. Factors which influence productivity of bucket wheel excavators are analyzed: dimensions and geometry of bucket wheels, rated power of drive systems for bucket wheels and properties of mined materials (coal or overburden). Indices used in Czechoslovakia for assessing productivity of bucket wheel excavators are compared. Factors which influence capacity of belt conveyors are also analysed: belt dimensions, belt geometry, angle of repose of hauled coal or overburden, and haulage speed of a belt conveyor. Investigations carried out in brown coal surface mines in Czechoslovakia show that conveyor ...

Energy Technology Data Exchange (ETDEWEB)

A p[sup +]-Al[sub 0.3]Ga[sub 0.7]As/n[sup +]-GaAs heterojunction tunnel diode was fabricated using Atomic Layer Epitaxy (ALE) growth technique. Background carbon doping of [similar to]10[sup 20] cm[sup [minus]3] was achieved in the p-side of the diode by optimizing growth conditions such as V/III ratio, exposure times to reactant gases, and growth temperature. In the n-side of the diode GaAs was doped with silane and doping concentrations as high as 7[times]10[sup 18] cm[sup [minus]3] were also achieved. The dopants are chosen to satisfy the high levels and low diffusion requirements. The diode can be used to interconnect the high and low band-gap cells in the AlGaAs/GaAs cascade solar cell structure. The reactor used in this investigation is a commercial MOCVD system which has been specially modified for dual operation of ALE and MOCVD growth modes.

Energy Technology Data Exchange (ETDEWEB)

The wind unit working wheel has 4 radial rectangular frames arranged in two vertical planes which are perpendicular to each other. In the planes limited by the frames, on loop hinges with limiting supports, there are flat blades. When the working wheel rotates under the influence of wind pressure, the blades automatically occupy a vertical or horizontal (wind vane) position depending on the direction of blade motion and the direction of wind velocity.

Energy Technology Data Exchange (ETDEWEB)

Computer simulations of two-junction, concentrator tandem solar cell performance show that IR-sensitive bottom cells are required to achieve high efficiencies. Based on this conclusion, two novel concentrator tandem designs are under investigations: (1) a mechanically stacked, four-terminal GaAs/GaInAsP (0.95 eV) tandem, and (2) a monolithic, lattice-matched, three-terminal InP/GaInAs tandem. In preliminary experiments, terrestrial concentrator efficiencies exceeding 30% have been achieved with each of the above tandem designs. Methods for improving the efficiency of each tandem type are discussed. (orig.).

Science.gov (United States)

... Wheeled Vehicle) equipped with a MILSTAR terminal was driven ... textbooks including Ronald W. Wolff, Stochastic Modeling and The ... Queue Length ...

UK PubMed Central (United Kingdom)

A liquid chromatography/tandem mass spectrometric (LC/MS/MS) assay was developed for the quantitative determination of salirasib (S-trans, trans-farnesylthiosalicylic acid,...Full Text Available

International Nuclear Information System (INIS)

The motivation for using a tandem electrostatic accelerator as an electron accelerator for a free electron laser (FEL) is presented. The adaptation of the HVEC EN tandem at the Weizmann Institute for this purpose, electron beam optics and nonlinear FEL computation relevant for this FEL realization are described. In the tandem configuration the terminal is held at a positive potential. The electron beam is accelerated from ground potential to the terminal in one beam tube and then decelerated down the other beam tube. The FEL wiggler and cavity are at the terminal. Due to the beam energy recovery this scheme produces a high power beam at the terminal with a small investment in electrical power. (orig.).

CERN Document Server

Here we show that self-propulsion in quantum vacuum may be achieved by rotating or aggregating magneto-electric nano-particles. The back-action follows from changes in momentum of electro-magnetic zero-point fluctuations, generated in magneto-electric materials. This effect may provide new tools for investigation of the quantum nature of our world. It might also serve in the future as a "quantum wheel" to correct satellite orientation in space.

Energy Technology Data Exchange (ETDEWEB)

Better properties of magnesium make it a natural choice for use as an anode material in rechargeable batteries. However, the magnesium alloy thin sheets used in rechargeable batteries were produced by ingot casting and rolling. That technology was so complex and the cost was high. Rapidly solidification by melt spinning is an effect way to solve that problem. In this paper, the technology of rapidly solidified (RS) ribbons in Mg-3%Al-1%Zn-0.2%Mn alloy has been investigated using melt spinning technique. The effect of wheel speed on thickness and microhardness of the ribbons is presented. Microhardness is found to increase with the wheel speed. Rapidly solidification leads to small grains (1{proportional_to}2 {mu}m). The plasticity of the ribbons was well. The quantity of Mg{sub 17}Al{sub 12} decreases with the increase in wheel speed. When the wheel speed reaches 1600 rpm, no Mg{sub 17}Al{sub 12} phase ...

Energy Technology Data Exchange (ETDEWEB)

The various factors that affect the open-circuit voltage ([ital V][sub oc]) of a two-terminal GaInP[sub 2]/GaAs tandem cell are examined. These include a) an anomalous problem associated with the GaAs bottom cell and b) back surface passivation of the thin GaInP[sub 2] top cell. Solutions to these problems are presented and yield tandem [ital V][sub oc]s close to the practical theoretical limits.

Energy Technology Data Exchange (ETDEWEB)

Describes performance of excavator teeth manufactured with a new hard alloy. The alloy was developed by the Donetskii Politeknicheskii Institute. Its composition consists of a high-chromium steel with a larger amount of titanium than serial alloy, and a nitrogen additive. Trial tests of new alloy teeth were carried out in the Severnyi and Vershinskii coal surface mines. The teeth were attached to EhRP, EhPG and EhR bucket wheel excavators. Abrasive wear of 129 experimental teeth and 134 serial teeth was compared for different excavation conditions. Test results are tabulated; advantages of the new experimental teeth are listed. 3 refs.

Energy Technology Data Exchange (ETDEWEB)

A description is given of the principal steps involved in `USIMINAS` work roll manufacturing project for its tandem cold mill. The service performance of these rolls was found to be similar to that rolls supplied by traditional manufacturers. (author). 5 refs., 5 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

This annual report describes research activities which have been performed with the JAERI tandem accelerator and the Van de Graaff accelerator from April 1, 2000 to March 31, 2001. Summary reports of 46 papers, and lists of publication, personnel and cooperative research with universities are contained. (author)

Energy Technology Data Exchange (ETDEWEB)

The electrical transport taking place in the {mu}c-Si tunnel recombination junction (TRJ) of a-Si:H/a-Si:H tandem solar cells and the role of CO{sub 2} plasma oxidation performed between microcrystalline layers is investigated in this paper with the computer code AMPS. Oxidized interfaces were modelled as simple highly defective intrinsic {mu}c-Si layers. Two different tunnel junction structures are studied in this paper: (a) (n){mu}c-Si/oxide/(p){mu}c-Si and (b) (n){mu}c-Si/(i){mu}c-Si/(p){mu}c-Si. In the last configuration the oxide interface is removed and replaced by a thin defective (i) {mu}c-Si layer. Both tunnel junctions have comparable theoretical and experimental tandem solar cell efficiencies which indirectly proves that our modelling assumption for oxidised interfaces is correct. A-Si:H/a-Si:H tandem solar cell efficiencies depend on the thickness of the intrinsic layer introduced in the tunnel junction. The ...

KoreaScience (Korea)

Full Text Available

Norwegian Open Research Archives (NORA)

Full Text Available

Wastenet

condenser, gas refiner, oil (gas) storage tank and dual fuel engine

British Library Electronic Table of Contents (United Kingdom)

A simple, sensitive and rapid method for analysis of granisetron in human plasma, utilizing liquid chromatography tandem mass spectrometry (LC-MS/MS), has been developed and validated to satisfy FDA guidelines for bioanalytical methods. The analyte and internal standard (IS) were isolated from 100ml plasma samples by liquid-liquid extraction (LLE). A Varian 1200l tandem mass spectrometer equipped with an electrospray ionization source was operated in selected reaction monitoring (SRM) mode with the precursor-to-product ion transitions m/z 313.4/138 for granisetron and m/z 270/201 for the IS used for quantitation. The assay exhibited a linear dynamic range of 0.02-20ng/ml for granisetron in human plasma. The lower limit of quantification (LLOQ) was 0.02ng/ml with a relative standard deviati...

Energy Technology Data Exchange (ETDEWEB)

As the Electric Power Industry is actively preparing for a restructured future where retail wheeling is practiced ideally and efficiently in a competitive market-based environment, concerns may arise legitimately on how system reliability and integrity can be ensured in an environment where markets have an enhanced role. As these concerns may be justified, at least for a transition period, this paper presents a proposal which outlines how the generally accepted requisite capacity, energy, and ancillary services standards may be satisfied through market reliance and minimal coordination by a Reliability Monitoring and Ancillary Services Managing Entity or Independent System Operator. A Strawman detailing one -- and by no means the only -- future scenario inspired by the recent NEPOOL restructuring discussions in New England is presented to demonstrate that market-based competition and flexibility are compatible with a reliable Power System.

UK PubMed Central (United Kingdom)

The genes which encode glycosomal glyceraldehyde-phosphate dehydrogenase (gGAPDH) of Trypanosoma cruzi are arranged as a tandemly repeated pair on a single chromosome and are identical at the level...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundYersinia pestis, the agent of plague, is a young and highly monomorphic species. Three biovars, each one thought to be associated with the last three Y....Full Text Available

UK PubMed Central (United Kingdom)

In this study we have profiled the free sterol content of cerebrospinal fluid by a combination of charge tagging and liquid chromatography-tandem mass spectrometry. Surprisingly, the most abundant cholesterol...Full Text Available

UK PubMed Central (United Kingdom)

Purpose: Reverse helical cone-beam computed tomography (CBCT) is a scanning configuration for potential applications in image-guided radiation therapy in which an accurate anatomic image...Full Text Available

Science.gov (United States)

The stability of a symmetric tandem mirror with hot-electron end plugs against low-frequency modes is investigated using a model first proposed by Baldwin. The Baldwin instability, which is due to the coupling of a negative-energy mode in the plug and a shear Alfven mode in the center cell, is confirmed. It is found that this instability is confined to small ranges of value of L/sub c/, the length of the center cell. Under modest restriction of parameters, the unstable regions in L/sub c/ impose little limitation on L/sub c/.

International Nuclear Information System (INIS)

The construction of the linear isomorphous and relativistic semigroup, of the Lorentz group and of tachyons was done using a dual pair of space-times, where the sought realization of the parametric semigroup is the semigroup of relativist endomorphisms. The obtained relativistic semigroup of dual space-time transformations possesses certain theoretical-probability properties.

Energy Technology Data Exchange (ETDEWEB)

The technology status of the dynamics and controls discipline as it applies to energy storage wheel systems was evaluated. No problems were identified for which an adequate solution could not be proposed. Design issues that influence control were addressed. The dynamics and control aspects associated with the energy storage system concept and its various constituent parts, and the control tasks attendant to large, manned spacecraft are discussed.

Science.gov (United States)

Understanding the detailed mechanics of these systems and their place in the general picture of binary star evolution are the dual objectives of this ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... two sectors. ' One company used as example of this process is the Lord Corporation, which produces products that reduce ...

British Library Electronic Table of Contents (United Kingdom)

In modern quality engineering, dual response surface methodology is a powerful tool to model an industrial process by using both the mean and the standard deviation of the measurements as the responses. The least squares method in regression is often used to estimate the coefficients in the mean and standard deviation models, and various decision criteria are proposed by researchers to find the optimal conditions. Based on the inherent hierarchical structure of the dual response problems, we propose a Bayesian hierarchical approach to model dual response surfaces. Such an approach is compared with two frequentist least squares methods by using two real data sets and simulated data.

Energy Technology Data Exchange (ETDEWEB)

An F-theory dual of a non-supersymmetric orientifold is considered. It is argued that the condensation of both open and closed string tachyons in the orientifold corresponds to the annihilation of branes and antibranes in the F-theory dual. One likely end-point of tachyon condensation is thus expected to be the vacuum of Type-IIB superstring. Some speculations are presented about the F-theory dual of the bosonic string and tachyon condensation thereof.

Energy Technology Data Exchange (ETDEWEB)

An investigation of current dual-fuel natural gas/diesel engine design, performance, and emissions was conducted. The most pressing technological problems associated with dual-fuel engine use were identified along with potential solutions. It was concluded that dual-fuel engines can achieve low NOx and particulate emissions while retaining fuel-efficiency and BMEP levels comparable to those of diesel engines. The investigation also examined the potential economic impact of dual-fuel engines in diesel-electric locomotives, marine vessels, farm equipment, construction, mining, and industrial equipment, and stand-alone electricity generation systems. Recommendations for further additional funding to support research, development, and demonstration in these applications were then presented.

Energy Technology Data Exchange (ETDEWEB)

Partial combustion of biomass in the gasifier generates producer gas that can be used for heating purposes and as supplementary or sole fuel in internal combustion engines. In this study, the potential of coir-pith and wood chips as the feedstock for gasifier is analyzed. The performance of the gasifier-engine system is analyzed by running the engine for various producer gas-air flow ratios and at different load conditions. The system is experimentally optimized with respect to maximum diesel savings and lower emissions in the dual fuel mode operation while using coir-pith and wood chips separately. The performance and emission characteristics of the dual fuel engine are compared with that of diesel engine at different load conditions. Specific energy consumption in the dual fuel mode of operation is found to be in the higher side at all load conditions. The brake thermal efficiency of the engine while using wood chips in ...

Energy Technology Data Exchange (ETDEWEB)

There are many factors contributing to the changes taking place within the electric utility industry. The environmental pressures on the industry are substantial and include the global warming issue, hazardous and nuclear waste challenges, air toxicities, and the electromagnetic field controversy. An issue of special concern is deregulation of the industry, which brought with it retail wheeling, wholesale wheeling, transmission access, and market-based pricing, all of which have greatly shaken the industry. The changes are expected to happen quickly. This is quite different from the 31 years it took to deregulate the telecommunications industry, the 15 to 20 years for railroads, the 9 years for the natural gas industry, and the 2 years for the airline industry. Historically there has been a general willingness among the utilites to share information through collaborative research. Research and development is viewed as a cost and not an ...

International Nuclear Information System (INIS)

The mapping of the magnetic flux bundle from the center cell to the Plasma Potential Control plates (PPC) on the end fan of the Tandem Mirror Experiment Upgrade (TMX-U), was improved by the addition of trim coils (12,000 amp-turns) on each side of each end fan next to the pump beam magnetic shields. The coils' axes are oriented perpendicular to the machine centerline. These coils made the necessary corrections to the field-line mapping, while keeping the field in the nearby pump beam magnetic shield below the saturation threshold. This paper briefly describes the problem, discusses the design as it evolved, and presents the results of the field testing. A brief description of the improvement in the machine performance is also included.

International Nuclear Information System (INIS)

In this paper, research on pass schedule of tandem cold mill (TCM) is carried out. According to load (reduction, rolling force, motor power) balance, non-linear equations set with variables of inter-stand thickness is constructed. The pass schedule optimization is carried out by solving the non-linear equations set. As the traditional method, the Newton-Raphson method is used for solving the non-linear equations set. In this paper a new simple method is brought up. On basis of the monotone relations between thickness and load, the inter-stands thickness is adjusted dynamically. The solution of non-linear equations set can be converged by iterative calculation. This method can avoid the derivative calculation used by traditional method. So, this method is simple and calculation speed is high. It is suitable for on-line control. (author)

British Library Electronic Table of Contents (United Kingdom)

Among pharmaceuticals and personal care products released into the aquatic environment, antibiotics are of particular concern, because of their ubiquity and health effects. Although scientists have recently paid more attention to the threat of antibiotics to coastal ecosystems, researchers have often focused on relatively few antibiotics, because of the absence of suitable analytical methods. We have therefore developed a method for the rapid detection of 36 antibiotic residues in coastal waters, including tetracyclines (TCs), sulfanilamides (SAs), and quinolones (QLs). The method consists of solid-phase extraction (SPE) and liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis, using electrospray ionization (ESI) in positive mode. The SPE was performed with Oasis HLB and Oasi...

Energy Technology Data Exchange (ETDEWEB)

This very significant and useful report assessed state-of-the-art geothermal technologies. The findings presented in this report are the result of site visits and interviews with plant owners and operators, representatives of major financial institutions, utilities involved with geothermal power purchases and/or wheeling. Information so obtained was supported by literature research and data supplied by engineering firms who have been involved with designing and/or construction of a majority of the plants visited. The interviews were conducted by representatives of the Bonneville Power Administration, the Washington State Energy Office, and the Oregon Department of Energy during the period 1986-1989. [DJE-2005

British Library Electronic Table of Contents (United Kingdom)

Tachycardia Detection, ICD, CRT-D Devices, Appropriate and Inappropriate Shock.-Introduction: We evaluated the frequency of appropriate and inappropriate shocks and survival in patients using dual-zone programming versus single-zone programming. Methods and Results: For the ALTITUDE REDUCES study, patients were followed for 1.6 1.1 years. The 12-month incidence of any shock was lower for dual-versus single-zone programmed detection at rates -170 bpm and between 170-200 bpm (P < 0.001). Appropriate shock rates at 1 year were also lower with dual-zone programming in these rate intervals (single zone 9.1%, 5.4%, P < 0.001, dual zone 6.7%, 4.7%, P < 0.02). There were no detectable differences between single- and dual-zone shock incidence at detection rates - 200 bpm (P = 0.14). Inappropriate s...

Energy Technology Data Exchange (ETDEWEB)

Autonomous robots or remotely operated vehicles have raised high hopes in the military and industrial communities because of the potential safety improvement and gain of productivity they may provide. Waste management on nuclear sites, pallet manipulation in factories, interventions on battle-fields, etc., are actively studied. A lot of these applications require powerful four-wheel vehicles, the kinematics of which is similar to that of a car. Such vehicles have three degrees of freedom: the (x,y) positions in a plane and the orientation of the vehicle. Path planning is often understood as only changing the position of the vehicle, whereas the tasks performed by this kind of robot requires a perfect orientation of the vehicle: forklifting a pallet or docking at a loading or unloading station requires accuracy in the orientation of the vehicle. It is this requirement and the kinematic constraints of the motion mode which have led to the path-planning algorithm ...

Energy Technology Data Exchange (ETDEWEB)

This study shows that the physical conditions necessary for thermal waves to materialize in Dual-Phase-Lagging porous media conduction are not attainable in a porous slab subject to a combination of constant heat flux and temperature (Neumann and Dirichlet) boundary conditions. It is demonstrated that the approximate equivalence between Dual-Phase-Lagging (DuPhlag) heat conduction model and the Fourier heat conduction in porous media subject to Lack of Local Thermal Equilibrium (La Lotheq) that suggested the possibility of thermal oscillations and resonance reveals a condition that cannot be fulfilled because of physical constraints. (author)

Energy Technology Data Exchange (ETDEWEB)

Testbed trials of the Sulzer RTA84 dual-fuel engine were successfully completed at the IHI Aioi engine works (Japan) in April 1986. This newly-developed engine, output range 15 to 40 MW, can be operated with both diesel or heavy oil and methane gas at comparable thermal efficiency and unchanged output. The RTA dual-fuel engine was developed in close collaboration between Sulzer Brothers Limited, Switzerland and its Japanese licensees Ishikawajima-Harima Heavy Industries Co. Ltd. (IHI), Nippon Kokan KK (NKK) and Sumitomo Heavy Industries Ltd. (SHI). Intended for the propulsion of LNG carriers, where the boil-off gas from the ship's cargo is exploited or for the generation of electricity in stationary plants, the RTA dual-fuel engine is an economic and reliable alternative to the steam or gas turbines.

Wastenet

... These tankers will be converted to a dual-fuel engine to enable them to run efficiently on the biomethane. The other half will be conditioned and injected into National Gridrsquo;s gas distribution network. This will provide enough renewable energy for all the heating and ...

Energy Technology Data Exchange (ETDEWEB)

Recently, utilization of natural gas, which is considered to be one of most important alternative fuels for petroleum, has been marked. As thermal efficiency of dual-fuel engine is higher than those of other prime movers with gaseous fuel, i.e., spark-ignited gas engine or gas turbine, it is possible to construct fuel-economical gas power plants with dual-fuel engines. However, its horsepower has been limited to the rather lower range. In 1984, NKK succeeded in developing large-sized dual-fuel engines based on the Pielstick PC4 diesel engine. The horsepower is 1200 HP/cyl, i.e. 21,600 HP for 18-cyclinder engine.

Energy Technology Data Exchange (ETDEWEB)

Lawrence Livermore National Laboratory (LLNL) has implemented a computer control system for operation of an FN tandem accelerator. The control software utilized is the Thaumaturgic Automated Control Logic (TACL) written by the Continuous Electron Beam Accelerator Facility and co-developed with LLNL. Details of the design philosophy, hardware configuration, control software, and special control algorithms will be presented. 2 refs., 4 figs.

CERN Document Server

By using a laser and maser in tandem, it is possible to obtain laser action in the hot exhaust gases involved in heat engine operation. Such a "quantum afterburner" involves the internal quantum states of working gas atoms or molecules as well as the techniques of cavity quantum electrodynamics and is therefore in the domain of quantum thermodynamics. As an example, it is shown that Otto cycle engine performance can be improved beyond that of the "ideal" Otto heat engine.

International Nuclear Information System (INIS)

The high-frequency precessional mode of a hot-electron-stabilized magnetic configuration has previously been shown to be stable in a window of core-plasma mass. Under conditions of frequency matching, the resulting stable negative-energy precessional wave can be destabilized by coupling to positive-energy shear-Alfven waves. Coupling is avoided when the hot-electron precession frequency exceeds the core-plasma ion gyrofrequency.

UK PubMed Central (United Kingdom)

4.5S RNA is a group of RNAs 90 to 94 nucleotides long (length polymorphism due to a varying number of UMP residues at the 3' end) that form hydrogen bonds with poly(A)-terminated RNAs isolated from...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper introduces in detail the compression performance of biogas, the application of compressed biogas to the compression-ignition engine and the possibility as well as the necessity of using compressed biogas. Moreover, the paper also goes further into some problems about the power increasing, efficiency raising and their social, economic and ecological beneficial results, when the compressed biogas is used in the compression ignition-dual fuel engine.

Energy Technology Data Exchange (ETDEWEB)

This review examines the characteristics of the compression-ignition type of dual-fuel engine and the combustion phenomena that affect these characteristics. The specific areas covered involve normal combustion processes, the nature and origin of engine knock, operation with LNG, and the effect of intake temperature on combustion efficiency and exhaust composition.

CERN Document Server

Lead tungstate crystals doped with small fractions of praesodynium or molybdenum have been tested in beams of high-energy electrons. The goal of these tests was to study the effects of such dopants on the capability to separate the signal components deriving from the Cherenkov and scintillation light generated by the beam particles. These studies were carried out in view of the possible application of such crystals in dual-readout calorimeters.

CERN Document Server

Predictions and measurements of a multimode waveguide interferometer operating in a fibre coupled, ``dual-mode'' regime are reported. With a 1.32 micrometer source, a complete switching cycle of the output beam is produced by a 10.0 nanometer incremental change in the 8.0 micrometer width of the hollow planar mirror waveguide. This equates to a fringe spacing of $\\sim\\lambda /130$. This is an order of magnitude smaller than previously reported results for this form of interferometer.

Energy Technology Data Exchange (ETDEWEB)

The modification of a turbocharged diesel engine to a dual-fuel engine using methane as the supplementary fuel has been carried out. The effect of the gaseous fuel in a turbo-charged diesel engine has been investigated by means of a heat release study and a computer program already developed at Leicester Polytechnic. It is used in order to examine the rate of heat released under any operational condition.

Energy Technology Data Exchange (ETDEWEB)

This paper presents the results of a new dual-fuel engine development program. The engine is the largest commercially available in terms of power output (650 hp/cyl) and features very low emissions (1 g/hp-hr NO[sub x]) and excellent fuel consumption (43 percent thermal efficiency). A two-cylinder turbocharged prototype was designed and built for the initial development. Results from testing on 18-cylinder production versions are also reported.

Energy Technology Data Exchange (ETDEWEB)

Dual-fuel engines are modified diesel engines burning simultaneously two fuels inside the cylinder: a gaseous one, called the primary fuel and a liquid one, called the pilot fuel. The thermal efficiency of the dual-fuel engine and of the diesel engine are comparable; the level of emissions is lower compared to the diesel one. This article presents a new procedure for the combustion modeling in a LPG-diesel dual-fuel engine. The procedures deals with the ignition delay period and with the rate of heat release inside the cylinder. This procedure is validated using experimental data issued front a collaboration with the Indian Institute of Technology from Madras, India. The used engine is a single-cylinder one, air-cooled. The pilot fuel is direct injected inside the cylinder The engine was run at constant load and with different diesel substitutions, i.e. for different air to fuel ratios of the primary fuel-air mixture. The ...

Energy Technology Data Exchange (ETDEWEB)

In 1995, MAN B&W Diesel launched a dual-fuel version of the successful L + V (in-line and vee) configurations of the 32/40 diesel engine series, covering a power range between 2.4 and 7.2 MW. In 1996, the company is launching a dual-fuel version of the L + V 48/60 engine series, moving the power range of dual-fuel engines to 16.2 MW. With its new dual fuel type 32/40 DG and 48/60 DG engines, MAN B&W Diesel has designed prime movers offering a high efficiency at low operating costs, while simultaneously meeting the most stringent NO{sub x} emission limits without any exhaust gas after-treatment. These engines are based on the successful HFO-operated four-stroke diesel engines. They offer environment-friendly and, operating at high mean effective pressures, simultaneously cost effective propulsion alternatives, especially if natural gas is used as a fuel. Extension of the compatibility to permit ...

Energy Technology Data Exchange (ETDEWEB)

We study the condensation of localized closed string tachyons on AdS orbifolds both from the bulk and boundary theory viewpoints. We first extend the known results for AdS{sub 5}/Z{sub k} to AdS{sub 3}/Z{sub k} case, and we proposed that the AdS{sub 3}/Z{sub k} decays into AdS{sub 3}/Z{sub k'} with k{sup '} < k. From the bulk viewpoint, we obtain a time-dependent gravity solution describing the decay of AdS orbifold numerically. From the dual gauge theory viewpoint, we calculated the Casimir energies of gauge theory vacua and it is found that their values are exactly the same as the masses of dual geometries, even though they are in different parameter regimes of 't Hooft coupling. We also consider AdS{sub 5} orbifold. The decay of AdS{sub 5}/Z{sub k} is dual to the transition between the vacua of dual gauge theory on R{sub t} x S{sup 3}/Z{sub k}. We constructed the ...

Energy Technology Data Exchange (ETDEWEB)

A method of abrasion testing according to ASTM C 704-76 a is presented for steel fibre concrete mortar, fusion-cast basalt and a surface coating material and results of practical interest are mentioned. Due to the high technical demands on these materials and their specific fields of application, the very first test already supplied interesting findings. From the user's point of view, the method is an interesting alternative to the common test methods, e.g. according to DIN 52 108 (wheel test according to Boehme). In English-speaking countries, testing according to ASTM is often mandatory in the refractory industry in order to assure constant quality of refractory materials after setting. The method is characterized by good comparability and high accuracy of measurement. Only the test piece is exchanged while the test conditions remain constant, so that accurate information on the material studied is obtained.

Energy Technology Data Exchange (ETDEWEB)

This paper presents the test results of a research program to investigate the performance of polymeric insulators for 15-kV dead-end applications on distribution systems. The test program involved both new insulators from five different manufacturers and naturally-aged insulators removed from service on the distribution system of Pennsylvania Power and Light. The test series to evaluate the new insulators included: preconditioning treatments, salt fog and tracking wheel accelerated aging tests, electrical tests, and material and physical tests. The tests for the naturally-aged insulators were mainly limited to the electrical tests and the material and physical tests.

Energy Technology Data Exchange (ETDEWEB)

The ultrasonic inspection pig system was described as being under development. This system was said to adopt the unique wheel type ultrasonic sensor which does not need couplant. This pig was designed to detect external corrosion in long-distance pipelines without interruption of the gas service. The wall-thickness measurement performance test and the travel performance test of the inspection pig in the test line confirmed that these performances satisfied the development specifications. However, the effect induced by the inner surface properties of the pipe and the influence of the pipe`s performance over long distances and for a long period of time still needed to be verified in an actual gas pipeline, and while the pipeline was actually in service. Improvements to the prototype model of the inspection pig were expected to include combinations of inspection pigs, with increases in battery and memory capacities to permit them to cope with in increased number of ...

British Library Electronic Table of Contents (United Kingdom)

A small fleet of classic London Taxis (Black cabs) equipped with hydrogen fuel cell power systems is being prepared for demonstration during the 2012 London Olympics. This paper presents a Life Cycle Analysis for these vehicles in terms of energy consumption and CO2 emissions, focusing on the impacts of alternative vehicle technologies for the Taxi, combining the fuel life cycle (Tank-to-Wheel and Well-to-Tank) and vehicle materials Cradle-to-Grave. An internal combustion engine diesel taxi was used as the reference vehicle for the currently available technology. This is compared to battery and fuel cell vehicle configurations. Accordingly, the following energy pathways are compared: diesel, electricity and hydrogen (derived from natural gas steam reforming). Full Life Cycle Analysis, usin...

British Library Electronic Table of Contents (United Kingdom)

The determination of residual stress (RS) in case-hardened steel gear truck synchronisers coated with thermal sprayed molybdenum was carried out using neutron and synchrotron X-ray diffraction. Two samples with different coating thicknesses (about 120 ?m and 1.4 mm) and different steel substrates (16MnCr5 and SAE4140, respectively) were investigated. Microanalysis revealed substantial porosity in both samples and some debonding was observed between the thin coating and the substrate. The bulk hardness of the SAE 4140 proved to be much higher than the 16MnCr5 and the surface case-hardening increased it by a further 20%. The full three-dimensional stress depth-profile was determined by neutron diffraction (ND) in both the coatings and the substrates, while synchrotron radiation allowed a dep...

Energy Technology Data Exchange (ETDEWEB)

Petroleum resources are finite and, therefore, search for their alternative non-petroleum fuels for internal combustion engines is continuing all over the world. Moreover gases emitted by petroleum fuel driven vehicles have an adverse effect on the environment and human health. There is universal acceptance of the need to reduce such emissions. Towards this, scientists have proposed various solutions for diesel engines, one of which is the use of gaseous fuels as a supplement for liquid diesel fuel. These engines, which use conventional diesel fuel and gaseous fuel, are referred to as 'dual-fuel engines'. Natural gas and bio-derived gas appear more attractive alternative fuels for dual-fuel engines in view of their friendly environmental nature. In the gas-fumigated dual-fuel engine, the primary fuel is mixed outside the cylinder before it is inducted into the cylinder. A pilot quantity of liquid fuel is ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to evaluate the synergistic effect of helium and hydrogen on Fe-Cr ferritic model alloys, to provide basic understanding concerning development of fusion reactor components. Single, dual and triple ion-beams consisting of Fe{sup 3+}, He{sup +} and H{sup +} were used for irradiation, at temperatures 470-600 deg. C and dose to 50 dpa at 1 {mu}m. The dual beam irradiation with He enhanced cavity nucleation extensively to swelling of about 0.4%, whereas the dual beam irradiation with H did not significantly affect the microstructure. In the case of triple ion irradiation, the synergistic effect of He and H was confirmed clearly; relative large void formation and enhanced swelling to almost 5%. The synergistic effect suggests that the role of H is important for void growth and dislocation bias.

Energy Technology Data Exchange (ETDEWEB)

The influence of engine operating variables on the performance, emissions and heat release in a compression ignition engine operating in normal diesel and dual-fuel modes (with natural gas fuelling) was investigated. Substantial reductions in NO{sub x} emissions were obtained with dual-fuel engine operation. There was a corresponding increase in unburned hydrocarbon emissions as the substitution of natural gas was increased. Brake specific energy consumption decreased with natural gas substitution at high loads but increased at low loads. Experimental results at fixed pilot injection timing have also established the importance of intake manifold pressure and temperature in improving dual-fuel performance and emissions at part load. (Author)

Energy Technology Data Exchange (ETDEWEB)

A compression ignition engine was operated on dual fuel principle inducting two commercial fuels and four pure hydrocarbon fuels in turn through intake manifold along with air and injecting diesel fuel to initiate the combustion in the conventional manner. The engine was operated at different loads and at each load the quantity of inducted fuel was increased gradually till knocking set in. The engine performance and exhaust pollutant emissions were recorded at different operating conditions. It was observed that the extent of induction and the effect on the performance depend on the properties of the inducted fuel such as volatility, self ignition temperature and oxidation characteristics. The energy release during the cycle was also observed to shift depending on the properties of inducted fuel. With the dual fuel operation, the thermal efficiency at part loads was observed to be less compared to neat diesel operation. The thermal efficiency ...

British Library Electronic Table of Contents (United Kingdom)

Flow visualization experiments are conducted in water tunnel for low aspect ratio cropped wings at low Reynolds number. The experimental results show that the model sweep angle ? influences the formation and development of the leading-edge vortex. For wings with ? =0?, the dominant flow structure is transverse vortex. When ??26?, the dual vortex structure can be observed at some angles of attack, and it is confirmed that the dual vortex is a special structure for flow over low aspect ratio wing at low Reynolds number. For ??56? wings, the dual vortex structure can be observed in a large range of attack angles. Moreover, in comparison with the outer vortex, the breakdown position of the primary vortex is delayed, and the larger the ?, the later the breakdown location at the same angle of at...

Energy Technology Data Exchange (ETDEWEB)

The performance of a gas-fuelled diesel engine (dual fuel) is examined at light load and an effective threshold limit to the combustion of the gaseous fuel through bulk flame spread is identified. The relationship of such a limit to some of the key operating parameters is then discussed. A comparison between the measured values of the limit with those corresponding to the lower flammability limits of the gaseous fuel when evaluated under the prevailing cylinder conditions during pilot diesel fuel ignition showed similar trends. It is suggested that such a similarity may form a basis for estimating the lean operation limits for duel a fuel combustion in engines. A simple approach for estimating the limiting equivalence ratio for the apparent bulk flame spread limit is described for a methane-fuelled dual fuel engine. (Author)

Energy Technology Data Exchange (ETDEWEB)

This paper describes a technique for implementing the ultrasonic inside diameter (ID) creeping wave technique for detection and sizing ID connected defects using a phased array ultrasonic system. The technique uses multiple focal laws to produce the examination modes. The first focal law is designed to create a shear wave nominally at the critical angle for mode conversion to a longitudinal wave at the ID of a part, thus creating a creeping wave. This focal law is focused at the ID to improve sensitivity. The rest of the laws are designed to create tandem sound paths that progress up a vertical surface directly above the focal point of the creeping wave generation point. When a defect on the inner surface is detected with the creeping wave, the height of the defect can be measured from the response of a set of tandem laws without readjusting the position of the probe. Results from standard one-inch long notches of varying depths are presented.

Energy Technology Data Exchange (ETDEWEB)

The Holifield Radioactive Ion Beam Facility (HRIBF) now under construction at the Oak Ridge National Laboratory will use the 25-MV tandem accelerator for the acceleration of radioactive ion beams to energies appropriate for research in nuclear physics; negative ion beams are, therefore, required for injection into the tandem accelerator. Because charge exchange is an efficient means for converting initially positive ion beams to negative ion beams, both positive and negative ion sources are viable options for use at the facility; the choice of the type of ion source will depend on the overall efficiency for generating the radioactive species of interest. A high-temperature version of the CERN-ISOLDE positive ion source has been selected and a modified version of the source designed and fabricated for initial use at the HRIBF because of its low emittance, relatively high ionization efficiencies and species versatility, and because it has been ...

Energy Technology Data Exchange (ETDEWEB)

A brief description of a method for producing relatively intense molecular negative ion beams for the difficult Group IIA elements is given which offers considerable improvement in terms of source operation and beam intensity stability over other methods conventionally utilized. It is particularly suited for use in cesium plasma sources such as the Aarhus geometry and axial geometry versions of the source. The method utilizes H/sub 2/ source feed gas for the production of a hydrogen-rich plasma discharge which sputters a negatively biased probe made of elemental or copper alloy material. Negative ion beams of MgH/sub 3//sup -/>=12 ..mu.. A have been realized during routine operation of the 25 MV tandem accelerator. Negative ion beam intensity data, typical source operational parameters, and examples of mass spectra associated with their production are given. Interesting intermetallic molecular negative ion beams consisting of the particular Group IIA element and ...

Energy Technology Data Exchange (ETDEWEB)

The general usefulness of neutron activation analysis (NAA) for samples containing the platinum group elements (PGE) and Au, either as major or trace constituents, is discussed. Charged particle activation is shown to be a viable or complementary alternative. Proton (6-10 MeV) and alpha particle (9-15 MeV) beams, produced in a tandem Van de Graaff accelerator, have been established to be the most effective choice. By taking advantage of the Coulomb barrier effect and the fact that many charged particle induced reactions have relatively large threshold values, the same instrumental technique can be applied, with minor modifications, to a wide range of materials.

Energy Technology Data Exchange (ETDEWEB)

Two sources of negative ions are described. An rf source produces up to 14 ..mu..A beams of He/sup -/ by charge exchange in Rb vapor. The other Source of Negative Ions by Cesium Sputtering (SNICS) produces a wide variety of negative ion beams in the ..mu..A range. Two important features of SNICS are its simple, compact construction and its very good beam emittance (2 to 4..pi..mm mrad MeV/sup 1/2/). Both sources have lifetimes >200 hours and they are used extensively on the Wisconsin EN tandem.

British Library Electronic Table of Contents (United Kingdom)

We operate a new NEC 250kV single-stage accelerator mass spectrometer (SSAMS) next to our established 5MV tandem. This permits good comparison of 14C-AMS and challenges SSAMS performance. Initial SSAMS ion-optical deficiencies have been addressed by shimming the injection magnet and 3permil 14C/13C measurement with background limited by sample chemistry is routine. Higher-precision analysis is also achievable. A problematic measurement interference remains, however. The small spectrometer was procured to add measurement capacity, and for experiments with positive ions, but is now the preferred instrument for both convenience and measurement quality.

Energy Technology Data Exchange (ETDEWEB)

We report on multijunction GaInP/GaAs photovoltaic cells with total-area efficiencies of 29.5% at one-sun concentration and air mass (AM) 1.5 global and 25.7% one-sun, AM0. These values represent the highest efficiencies achieved by any solar cell under these illumination conditions. Three key areas in this technology are identified and discussed: the grid design, front surface passivation of the top cell, and bottom surface passivation of both cells. Aspects of cell design related to its operation under different solar spectra and under concentration are also discussed.

British Library Electronic Table of Contents (United Kingdom)

Purpose Study the radiolysis of solid-state metoclopramide hydrochloride at various absorbed doses. Elucidate the structure of the degradation products to gain information on the radiolysis mechanisms. Methods Solid-state metoclopramide samples were irradiated at several doses with gamma rays and high-energy electrons to evaluate the influence of the dose rate. High-performance liquid chromatography with a diode array detector was used to measure the chemical potency as a function of the absorbed dose and to quantify the degradation products. The characterization of degradation products was performed by liquid chromatography/atmospheric pressure chemical ionization/tandem mass spectrometry. Results The degradation of solid-state metoclopramide after irradiation was negligible. No qualitati...

Energy Technology Data Exchange (ETDEWEB)

Eukaryotic genomes encode a zinc finger protein (ZPR1) with tandem ZPR1 domains. In response to growth stimuli, ZPR1 assembles into complexes with eukaryotic translation elongation factor 1A (eEF1A) and the survival motor neurons protein. To gain insight into the structural mechanisms underlying the essential function of ZPR1 in diverse organisms, we determined the crystal structure of a ZPR1 domain tandem and characterized the interaction with eEF1A. The ZPR1 domain consists of an elongation initiation factor 2-like zinc finger and a double-stranded {beta} helix with a helical hairpin insertion. ZPR1 binds preferentially to GDP-bound eEF1A but does not directly influence the kinetics of nucleotide exchange or GTP hydrolysis. However, ZPR1 efficiently displaces the exchange factor eEF1B from preformed nucleotide-free complexes, suggesting that it may function as a negative regulator of eEF1A activation. Structure-based mutational and ...

UK PubMed Central (United Kingdom)

BackgroundIn Arabidopsis, INDOLE-3-BUTYRIC ACID RESPONSE5 (IBR5), a putative dual-specificity protein phosphatase,...Full Text Available

UK PubMed Central (United Kingdom)

A large percentage of patients with HIV/AIDS will develop dermatological complications. Consequently, all practising clinicians and pathologists in regions with a high prevalence of HIV/AIDS must be...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

We study the impact of non-Abelian T-duality transformations on a string based cosmological model. The implementation of the pre-big-bang scenario is investigated. We found a region of the dual phase where such a picture is possible.

Energy Technology Data Exchange (ETDEWEB)

This book contains papers relating to the 1990 Future Transportation Technology Conference and Exposition. Included are the following papers; Examination of rich mixtures operation of a dual fuel engine, A hybrid natural gas vehicles, Performance analysis of a spark ignited engine with ETBE as a blending agent.

UK PubMed Central (United Kingdom)

A two-channel optical system has been developed to provide spatially resolved simultaneous imaging of singlet molecular oxygen (¹O₂) phosphorescence and photosensitizer (PS) fluorescence...Full Text Available

UK PubMed Central (United Kingdom)

In response to oxidative stress, the transcription factor NF-E2-related factor 2 (Nrf2) controls the fate of cells through transcriptional upregulation of antioxidant response element (ARE)-bearing...Full Text Available

UK PubMed Central (United Kingdom)

Improved NMR detection of mass limited samples can be obtained by taking advantage of the mass sensitivity of microcoil NMR, while throughput issues can be addressed using multiple, parallel...Full Text Available

International Nuclear Information System (INIS)

To assess the diagnostic capability Fuji computed radiography (FCR) using a dual side reading system was compared to the conventional radiography using a film-screen system. Twenty-eight patients with lung cancer were examined with a new FCR system (FCR 5501D) and a conventional screen-film system concurrently. FCR utilizes a reading system that detects emissions from dual sides of imaging plate. Chest X-rays were obtained with same exposure factors in both systems. Image qualities of both systems were compared by two radiologists using a five-level score. There were no lesion that FCR images were inferior to film-screen images. The frequency of score +1 or +2 that FCR images were superior to film-screen images was 31% in large nodular shadows, 40% in accompanying shadows with a nodule, 67% of small nodular shadows, and 43% of the lymph node swelling in the hilum of the lung or mediastinum. In large nodular shadows which were the most frequent ...

UK PubMed Central (United Kingdom)

Antiplatelet resistance has been proposed as a possible mechanism to explain recurrent cardiovascular events in patients who have coronary artery disease and who are undergoing dual antiplatelet therapy....Full Text Available

Energy Technology Data Exchange (ETDEWEB)

We have investigated the nanocrystalline microstructure and the hard magnetic properties of Sm(Co{sub 0.725}Fe{sub 0.1}Cu{sub 0.12}Zr{sub 0.04}B{sub 0.015}){sub 7.4} melt-spun ribbons. The coercivity (H{sub c}) of the as-spun ribbons increased with the wheel surface speed from 2.8kOe for 10m/s to 14.5kOe for 40m/s. The post-annealing of the melt-spun ribbons from 700 to 900 deg. C for 10min did not lead to a substantial increase of H{sub c}. However, after isothermal aging at 820 deg. C and subsequent slow cooling (0.5 deg. C/min) to 120 deg. C, H{sub c} increased from 2.8 to 10.9kOe for 10m/s, while it decreased from 14.5 to 13.5kOe for 40m/s ribbons. The grain size of the melt-spun ribbon reduced with structural transformation from 2:17H (Th{sub 2}Ni{sub 17}-hexagonal type) to 1:7H (TbCu{sub 7}-hexagonal type) as the wheel surface speed was increased. Three-dimensional atom probe analysis showed a boron enriched precipitate at the grain ...

Energy Technology Data Exchange (ETDEWEB)

In May 1995, the California Public Utilities Commission (CPUC) released two proposals for restructuring the state`s electric power industry. The two proposals follow more than a year of testimony and public comment after the CPUC issued the ``Blue Book`` (CPUC 1994a) on April 20, 1994, which called for retail wheeling to be phased in to all customers over 5 years. The majority proposal, supported by three of the four CPUC commissioners (one seat was vacant when the proposals were released), calls for creating a central pool, or ``poolco``; setting electric prices to reflect true costs of service, or ``real-time pricing``; and allowing parties to negotiate ``contracts for differences`` between the pool price and the contract price. The minority proposal, sponsored by Commissioner Jesse Knight, calls for retail wheeling, or ``direct access,`` and for utilities to divest or spin off their generating assets. This paper presents a summary of the ...

Energy Technology Data Exchange (ETDEWEB)

To utilize ethanol from agricultural residue as a fuel in diesel engines, a dual-fuel engine was developed. The engine, which was equipped with a system to electrically control diesel and alcohol flow rates, met basic requirements of a tractor engine, including engine speed control and setting of the torque curve. However, engine knock due to alcohol was a significant drawback. A diesel injection pump with a timing and flow rate control system was adapted, and the effect of injection timing on combustion and performance was investigated. It was observed that the timing control was effective in reducing engine knock caused by rapid alcohol combustion. (author)

Energy Technology Data Exchange (ETDEWEB)

Knock limitations are investigated using natural gas, with diesel pilot ignition, as a fuel for the 3406 DI-TA Caterpillar diesel engine. Thermodynamic properties at TDC are generated by computer and compared with experimental results. Exhaust emissions are analyzed. A comparison is made of dual-fuel operation relative to diesel. Observations are made to determine the onset of knock. The onset of knock is characterized as a function of engine speed, load, inlet manifold temperature, and air-fuel ratio (A/F). The conditions at the inset of knock are determined using cylinder pressure data. The most efficient operating range is determined with knock avoidance as a prime parameter.

Energy Technology Data Exchange (ETDEWEB)

Fairbanks Morse Engine Division of Coltec Industries is ready to move into the cogeneration market with its well established engine program. Over the past six years the company has been refining and improving both the 38D8-1/8 opposed piston and PC2.5 dual-fuel engines in several areas. The most important targets achieved are higher power output, lower exhaust emissions, better fuel economy, better maintainability and longer life. The result is the Enviro-Design series of engines which the company believes will find broad application in the power generation and cogeneration fields. 3 figs.

International Nuclear Information System (INIS)

In dual-energy projection radiography with double exposures, rapid energy switching is mandatory to eliminate motion artifacts, but it is costly for use in a clinical environment. We developed a system with practical exposure intervals at reasonable cost by modifying a condenser-type X-ray generator. A commercially available system for digital radiography (Fuji Computed Radiography, FCR) was used to subtract images. This report dealt with technical factors to obtain adequate kV and mAs settings in this technique. (author).

Science.gov (United States)

The dual-media approach to contaminant transport modeling has emerged over the years as a clear improvement over the conventional Fickian advection-dispersion, or single-medium model, in an increasing number of settings. Recent application to the MADE-2 tracer test at Columbus Air Force Base has extended interest to field-scale plume migration in unconsolidated sediments. Subsequent application to tritium migration from the SRS F- and H-area seepage basins within this study also demonstrated improved transport predictions.

Energy Technology Data Exchange (ETDEWEB)

There is renewed interest in the development of natural gas vehicles in response to the challenge to reduce urban air pollution and consumption of petroleum. The natural gas/diesel dual fuel engine is one way to apply natural gas to the conventional diesel engine. Dual fuel engines operating on natural gas and diesel emit less nitrogen oxides, and less carbon soot to the air compared to conventional diesel engines. The problem is that at light loads, fuel efficiency is reduced and emissions of hydrocarbons and carbon monoxide are increased. This thesis focused on control methods for emissions of hydrocarbons and carbon monoxide in the dual fuel engine at light loads. This was done by developing a reverse flow catalytic converter to complement dual fuel engine exhaust characteristics. Experimental measurements and numerical simulations of reverse flow catalytic converters were conducted. Reverse flow ...

International Nuclear Information System (INIS)

Effect of helium and hydrogen production on radiation-hardening of F82H irradiated by dual or triple beam condition were investigated. The specimens used were four types of ferritic martensitic steels of F82H-std (Fe-8Cr-2W-0.2V-0.04Ta-0.1C) steels tempered at 750degC for 60 minutes, 20% cold worked F82H steel, F82H tempered for 10 minutes and non-tempered F82H steels. The irradiation was performed at 450degC to 50 dpa under simultaneous dual beams of 10.5 MeV Fe"3"+ and 1.05 MeV He"+ or triple beams of those and 380 keV H"+ ions. The ratios of He (appm)/dpa and H(appm)/dpa were 15 nad 15 (or 150) for dual and triple ion beams. The hardness of the irradiated specimens measured at room temperature using a micro indentation after the irradiations. The hardness in these F82H steels irradiated at 450degC to 18 dpa under triple beam irradiation was harder than that under dual beam irradiation. Irradiation ...

Energy Technology Data Exchange (ETDEWEB)

The use of jojoba methyl ester as a pilot fuel was investigated for almost the first time as a way to improve the performance of dual fuel engine running on natural gas or liquefied petroleum gas (LPG) at part load. The dual fuel engine used was Ricardo E6 variable compression diesel engine and it used either compressed natural gas (CNG) or LPG as the main fuel and jojoba methyl ester as a pilot fuel. Diesel fuel was used as a reference fuel for the dual fuel engine results. During the experimental tests, the following have been measured: engine efficiency in terms of specific fuel consumption, brake power output, combustion noise in terms of maximum pressure rise rate and maximum pressure, exhaust emissions in terms of carbon monoxide and hydrocarbons, knocking limits in terms of maximum torque at onset of knocking, and cyclic variability data of 100 engine cycles in terms of maximum pressure and its pressure rise rate ...

Energy Technology Data Exchange (ETDEWEB)

We wanted to evaluate the long-term results of a dual expandable nitinol stent for the palliative treatment of malignant gastroduodenal strictures. The dual stent consists of two stents; an outer partially nylon covered stent and an inner bare nitinol stent. The outer stent was placed into the stricture and this was followed by coaxial placement of the inner bare stent. Using fluoroscopic guidance, dual expandable stents were placed in 86 patients with inoperable malignant gastroduodenal strictures. The technical and clinical success, the complication, survival and the stent patency were evaluated during the follow-up period. Stent placement was technically successful in 83 of the 86 patients. After stent placement, 74 of the 85 patients showed improvement of their symptoms. During the mean follow-up period of 133 days, 24 patients (28%) developed recurrent symptoms due to incomplete expansion (n=1), stent migration (n=4), ...

Energy Technology Data Exchange (ETDEWEB)

A system for real-time neutron radiography of moving objects is described. It comprise a source adapted to generate a continuous uninterrupted series of neutron pulses. Each pulse has a predetermined peak power and duration compatible with the framing times of a real-time video imaging system. A transporter moves an object to be examined to bring sequentially position selected portions of the object in the path of the pulses. Where the object itself has moving components, pulses are sequentially incident on the object. According to any dissimilarities, the object will alter the intensity of the neutrons passing therethrough. In order to record separately the changes in the neutron intensity, for each pulse, an imager is positioned to receive the neutron beam pulses which have been altered by their passage through the object and produce images indicating intensity alterations. A refrigerated beryllium filter can be used to effectively eliminate thermal neutrons from the pulses and ...

Energy Technology Data Exchange (ETDEWEB)

Pellet injectors are needed to fuel long pulse tokamak plasmas and other magnetic confinement devices. For this purpose, an apparatus has been developed that forms 1.3-mm-diam pellets of frozen deuterium at a rate of 40 pellets per second and accelerates them to a speed of 1 km/s. Pellets are formed by extruding a billet of solidified deuterium through a 1.3-mm-diam nozzle at a speed of 5 cm/s. The extruding deuterium is chopped with a razor knife, forming 1.3-mm right circular cylinders of solid deuterium. The pellets are accelerated by synchronously injecting them into a high speed rotating arbor containing a guide track, which carries them from a point near the center of rotation to the periphery. The pellets leave the wheel after 150/sup 0/ of rotation at double the tip speed. The centrifuge is formed in the shape of a centrifugal catenary and is constructed of high strength KEVLAR/epoxy composite. This arbon has been spin-tested to a tip speed of 1 km/s.

International Nuclear Information System (INIS)

The performance of the gas-jet transport system coupled to the RIKEN gas-filled recoil ion separator GARIS was investigated using 255No produced in the 238U(22Ne, 5n)255No reaction. Alpha particles of 255No separated with GARIS and transported by the gas-jet system were measured with a rotating wheel apparatus for ? spectrometry under low background condition. The high gas-jet efficiencies of about 75% were independent of the recoil ranges of 255No in the gas-jet chamber. The present results suggest that the GARIS/gas-jet system is a promising tool for the next-generation superheavy element chemistry: (1) the background radioactivities of unwanted reaction products are strongly suppressed, (2) the intense beam is absent in the gas-jet chamber and hence the high gas-jet efficiency is achieved, and (3) the beam-free condition also allows for investigations of new chemical systems. (author)

Energy Technology Data Exchange (ETDEWEB)

ATLAS is one of the four experiments which will take place at the LHC, the CERN future protons collider. This accelerator, which should start in 2007, will allow to continue the studies carried out by its predecessors, as the standard model Higgs boson and new physics searches. The very high luminosity -10 fb{sup -1} during the first three functioning years, then 100 fb{sup -1}- and the 14 TeV in the frame center will ease these studies. The Centre de Physique des Particules de Marseille took part in the ATLAS collaboration, taking in charge half of the End-cap electromagnetic calorimeter modules construction. The description of this sub-detector and the construction steps, in particular the electrical tests which allow the stacking validation, are presented in this document. These tests results, obtained for the live first production modules, are analysed. The pre-series module (module 0) performances, obtained with beam tests performed at CERN in 1999, are also presented. The ...

International Nuclear Information System (INIS)

Several different aspects of the influence of the target backing on in-beam electron spectra following compound nuclear reactions induced by accelerated ions at tandem energies irradiating backed targets are discussed in detail. This discussion is illustrated by a few typical examples, such as "1"2C"5"+ and "3"1P"1"0"+ beams at 4 MeV/u bombarding Sn(+Be), Sn(+Au), Pb(+C) backed targets. Moreover, the relative influence of electron backscattering, electron Doppler shift and Doppler broadening as well as #delta#-electron emission on the low energy electron spectra (E_e#<=#100 keV) obtained under such conditions are investigated in the frame of the available experimental data. (orig.).

British Library Electronic Table of Contents (United Kingdom)

As a consequence of the close integration of cattle into the food chain of humans, forensically relevant cases involving cattle (Bos taurus) DNA analysis are common. However, scientific publications reporting the information content of the commonly used bovine short tandem repeat (STR) loci remains scarce. Population studies were performed for 16 polymorphic STR loci (BM1818, BM1824, BM2113, CSRM60, CSSM66, ETH3, ETH10, ETH225, HAUT27, ILSTS006, INRA023, SPS115, TGLA53, TGLA122, TGLA126, and TGLA227) including 4,162 randomly selected cattle representing 20 distinct breeds. The power of parental exclusion, expected and observed heterozygosity, probability of identity, and non-amplifying (?null?) allele frequencies were calculated. Major differences existed in the information content between...

British Library Electronic Table of Contents (United Kingdom)

BACKGROUND AND PURPOSE It is well established that cytochrome P450 2J (CYP2J) enzymes are expressed preferentially in the heart, and that ebastine is a substrate for CYP2J, but it is not known whether ebastine is metabolized in myocardium. Therefore, we investigated its pharmacokinetics in the rat isolated perfused heart. EXPERIMENTAL APPROACH Rat isolated hearts were perfused in the recirculating mode with ebastine for 130-min. The concentrations of ebastine and its metabolites, hydroxyebastine and carebastine, were measured using liquid chromatography with a tandem mass spectrometry. The data were analysed by a compartmental model. The time course of negative inotropic response was linked to ebastine concentration to determine the concentration-effect relationship. KEY RESULTS Ebastine w...

Energy Technology Data Exchange (ETDEWEB)

An energy saving dc-dc converter circuit is disclosed having two energy efficient means which operate in tandem, an energy conserving means and a voltage doubling means. These energy efficient means are applied in combination with elements commonly found in dc-dc converter circuits, namely an ac voltage generator, a transformer for stepping up the generated ac voltage, and means for storing the converted dc voltage. The energy conserving means is connected to the dc voltage storage means. It comprises a resettable inhibit circuit which cuts off the provision of dc voltage for conversion for a predetermined interval when the output of the converter exceeds a predetermined level. The voltage doubling means is reponsive to outputs of the inhibit circuit of the energy conserving means and the ac voltage generator. It provides a phase inverted waveform of the generated ac voltage on one of two leads to the ac voltage step-up transformer.

Science.gov (United States)

Synthetic efforts toward the homoerythrina alkaloids 1-3 are described. Two separate model systems guided the pivotal [3 + 2] azomethine ylide cycloaddition cascade to form the A-C rings of these alkaloids. The cycloaddition precursors 63 and 68, prepared in nine and ten steps, respectively, from alkyne 47, each contain an enolizable ketone, a tethered electrophile, and an electron-poor dipolarophile. Heating 63 and 68 with the stannyl amine 17 generated demethoxyschelhammeridine 65 and demethoxyschelhammericine 70, the products of intramolecular azomethine ylide cycloadditions. Subsequent attempts to install the C-3 methoxy group of 1-3 are also described. PMID:17465572

Energy Technology Data Exchange (ETDEWEB)

This is a report on modification of a locomotive diesel engine to a dual-fuel engine to determine if the dual fuel engine in railway service will provide high performance, lower fuel and maintenance costs. After the locomotive was modified and the new governor and linkage were installed by General Motors at the BN's Northtown Diesel Shop near Minneapolis, the locomotive went through startup procedures. General Motors participated in startup. Some calibration, adjustments and minor piping changes were required but in general the problems encountered in startups were quite insignificant. The locomotive was connected to the load box (static test) during startup and at 720 RPM exceeded the required output for this test as established by the parties. Operation on straight oil over the range from idle through No. 8 throttle notch and on dual fuel from No. 5 through No. 8 throttle notch was smooth as was the transfer from ...

Energy Technology Data Exchange (ETDEWEB)

The fuel-injection system of the Niigata 6L 16X-AG dual-fuel engine is structured to steadily supply injected fuel during diesel-engine operation, and to distribute oil at a low rate to all the cylinders during gas-engine operation. The dual-fuel engine is started by the diesel engine operation and is changed over to gas-engine operation when the load increases. This change over is done automatically with a link mechanism. Regarding the gas-supply system, the changing pressure of supply gas is controlled by a pressure control valve which is stable and most adequate for the engine. The dual-fuel engine has the following features: (1) a high compression ratio is adopted, which reduces fuel consumption and thermal efficiently; (2) if the supply of gas decreases or stops, while continuing loaded operations, it can immediately shift to diesel engine operation automatically and continue the operation; (3) ignition is done by the ...

Energy Technology Data Exchange (ETDEWEB)

Diesel engines operating on gaseous fuels are commonly known as dual-fuel engines. In the present work, a single-cylinder, compression ignition, indirect injection research (Ricardo E6) engine has been installed at United Arab Emirates University for investigation of the exhaust emissions when the engine is operating as a dual-fuel engine. The influence of changes in major operating and design parameters, such as the concentration of gaseous fuel in the cylinder charge, pilot fuel quantity, injection timing and intake temperature, on the production of exhaust emissions was investigated. Diesel fuel was used as the pilot fuel, while methane or propane was used as the main fuel which was inducted in the intake manifold and mixed with the intake air. The experimental investigations showed that the poor emissions at light loads can be improved significantly by increasing the concentration of gaseous fuel (total equivalence ratio), employing a large ...

International Nuclear Information System (INIS)

The surface layer optimized in resistance of corrosion and wear has been obtained by W + C dual implantation on H13 steel. The electrochemical polarization measurements show that the peak current density I_D is increased and then saturated with increasing of voltage scanning loops. The I_D is 100 times smaller than that of H13 steel, and 2-3 times smaller than that of tungsten. Then influence of dual implantation order on corrosion resistance is also studied. The I_D for W_5C_8 implanted first with W is half of that for C_5W_5 implanted first with C. The corrosion resistance structure of the samples after corrosion is observed by SEM. The X-ray analysis indicates that the structure consists of disperse phases of WC, W_2C, FeW, Fe_2W, FeW_2C and iron carbides. It is shown from Auger analysis that the optimum complex layer for corrosion resistance consists of thin carbon film on surface, disperse phases of these metal compounds in middle and then ...

Science.gov (United States)

The bone mineral content of 109 lumbar vertebrae from 36 different subjects was determined by dual photon absorptiometry. The mean age of the subjects was 58.5 years (range, 31 to 79 years). The ultimate strength of the vertebral bodies was determined during axial compression. Bone mineral content and ultimate compressive strength were correlated (r = 0.86) and the strength was found to increase linearly with increasing amounts of bone mineral content. No differences in this correlation were found in the four vertebral levels (L-4) included in the study, but a difference in this correlation was found between specimens taken from male and female subjects. The results make it possible to estimate the strength of a vertebral body from the knowledge of its bone mineral content as determined by dual photon absorptiometry and provide a basis of estimations of normal and abnormal amounts of bone mineral content in the vertebrae of the lumbar spine. ...

Energy Technology Data Exchange (ETDEWEB)

An experimental and modelling study was performed for a reverse flow catalytic converter attached to a natural gas/diesel dual fuel engine. The catalytic converter had a segmented ceramic monolith honeycomb substrate and a catalytic washcoat containing a predominantly palladium catalyst. A one-dimensional single channel model was used to simulate the operation of the converter. The kinetics of the CO and methane oxidation followed first-order behaviour. The activation energy for the oxidation of methane showed a change with temperature, dropping from a value of 129 to 35 kJ/mol at a temperature of 874 K. The reverse flow converter was able to achieve high reactor temperature under conditions of low inlet gas temperature, provided that the initial reactor temperature was sufficiently high. (author)

Energy Technology Data Exchange (ETDEWEB)

A process is described for converting organic waste into a combustible gas for use in a heavy duty thermal engine. The engines best suited for this operation are of the dual-fuel type whose output power results from the simultaneous work of 2 combustibles. The gas flow rate is controlled by the desired power output, while diesel fuel injection remains constant regardless of engine load. The low BTU gas produced by the gasification of dry wastes is a mixture of CO, H/sub 2/ CH/sub 4/, CO/sub 2/ and N/sub 2/. Diesel fuel savings under usual operating conditions is no less than 80% of the consumption of conventional diesel engines of identical power. Characteristics of the low Btu gas engines are described as are the characteristics of the gasifying equipment. Applications for this process are suggested. (DMC)

Energy Technology Data Exchange (ETDEWEB)

This patent describes a low emission duel fuel engine system. It comprises: a dual fuel engine having a combustion chamber; a fuel oil supply connected to the engine; a fuel gas supply connected to the engine; and means connected between the fuel oil supply and the engine for injecting fuel oil into the engine. The means connected between the engine and fuel oil supply limiting the injection of fuel oil to the combustion chamber to pilot ignition quantities only, wherein the limiting means includes means for limiting the injection of fuel oil such that the exhaust emission of NO{sub x} is at an emission rate of less than 1 GM/PH-HR, whereby the exhaust emission performance of the dual fuel engine is enhanced.

CERN Document Server

One of the salient features of human perception is its invariance under dilatation in addition to the Euclidean group, but its non-invariance under special conformal transformation. We investigate a holographic approach to the information processing in image discrimination with this feature. We claim that a strongly coupled analogue of the statistical model proposed by Bialek and Zee can be holographically realized in scale invariant but non-conformal Euclidean geometries. We identify the Bayesian probability distribution of our generalized Bialek-Zee model with the GKPW partition function of the dual gravitational system. We provide a concrete example of the geometric configuration based on a vector condensation model coupled with the Euclidean Einstein-Hilbert action. From the proposed geometry, we study sample correlation functions to compute the Bayesian probability distribution.

Energy Technology Data Exchange (ETDEWEB)

One of the unsolved problems of the natural gas dual fuel engine is that there is too much exhaust of Total Hydrogen Carbon(THC) at a low equivalent mixture ratio. To fix it, a natural gas mixed with hydrogen was applied to engine test. The results showed that the higher the mixture ratio of hydrogen to natural gas, the higher the combustion efficiency. And when the amount of the intake air is reached to 90% of WOT, the combustion efficiency was promoted. But, like a case making the injection timing earlier, the equivalent mixture ratio for the nocking limit decreases and the produce of NOx increases. 5 refs., 9 figs., 1 tab.

International Nuclear Information System (INIS)

An Fe-15Cr-20Ni ternary model alloy and a Type 316 stainless steel were irradiated by dual-ions at 1 to 50 appm of He/dpa ratios, to investigate the helium effects on microstructural development in austenitic alloys under irradiation. Quantitative analysis on resultant microstructures revealed that the Frank loop nucleation rate and the network dislocation density positively correlate and Frank loop growth rate negatively correlate with the He/dpa ratio, while the cavity growth rate has its peak at an intermediate helium injection rate. Although He/dpa dependence of various microstructural features were similar for the model alloy and the 316SS, the rates of their development and the mechanism which had assisted cavity growth were significantly different in these two materials. (orig.).

Science.gov (United States)

Bechtel Power Corporation has performed an evaluation of flue gas desulfurization (FGD) system cost versus design level of operating availability for an industrial sized dual-alkali process. Two principle sources were used: the Flue Gas Desulfurization Information System (FGDIS) maintained by the Environmental Protection Agency and budget quotations from an FGD vendor. A survey of the FGDIS data base proved inconclusive in establishing a relationship between FGD system cost and operating availability. Using equipment failure rates derived from various sources, component availability factors were developed for all major FGD system components. Cost and availability data of nine industrial FGD system configurations were analyzed on a per boiler basis. Linear curve fitting of these data produced mathematical relationships of cost and availability.

Energy Technology Data Exchange (ETDEWEB)

Plasma erosion craters caused by electrical discharges on the surface of materials are important features of the erosion processes resulting in the degradation of electrodes. In the present work, electrical discharges were produced on a bi-metallic Ni/Cu multilayered surface. By means of dual beam techniques, coupling a focused ion beam (FIB) and a scanning electron microscope (SEM), not only the surface but also the sub-surface structure of the craters were investigated. Using the combination of SEM, FIB and STEM-EDX, a complete three-dimensional investigation of the craters were carried out. The analysis of the microstructure modifications as a function of depth enabled to determine the field of interaction between the plasma and the material. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The Holifield Radioactive Ion Beam Facility now under construction at the Oak Ridge National Laboratory will use the 25 MV tandem accelerator for the acceleration of radioactive ion beams to energies appropriate for research in nuclear physics; negative ion beams are, therefore, required for injection into the tandem accelerator. Because charge exchange is an efficient means for converting initially positive ion beams to negative ion beams, both positive and negative ion sources are viable options for use at the facility. The choice of the type of ion source will depend on the overall efficiency for generating the radioactive species of interest. Although direct-extraction negative ion sources are clearly desirable, the ion formation efficiencies are often too low for practical consideration; for this situation, positive ion sources, in combination with charge exchange, are the logical choice. The high-temperature version of the CERN-ISOLDE ...

Energy Technology Data Exchange (ETDEWEB)

Radioactive ion beams (RIBs) of short-lived isotopes of fluorine are in demand for investigating astrophysical phenomena related to the hot CNO cycle and rp processes responsible for stellar nucleosynthesis. Since negative ion beams are required for injection into tandem electrostatic accelerators, such as the 25 MV tandem accelerator used for post acceleration of RIBs for the Holifield Radioactive Ion Beam Facility (HRIBF) research program at the Oak Ridge National Laboratory (ORNL), efficient, direct-formation F{sup -} ion sources are highly desirable for RIB applications involving this type of post-accelerator. We have conceived and evaluated a direct extraction F{sup -} source for potential RIB applications which is predicated on the reverse polarity operation of a positive electron-beam-plasma target/ion source (EBPTIS) while simultaneously feeding fluorine rich compounds and Cs vapor into the source. The source is found to operate in two ...

Energy Technology Data Exchange (ETDEWEB)

This paper gives details of the development of the Wartsila 32DF duel-fuel lean-burn engine that can burn liquid or gaseous fuels, and reports on the installation of four of the engines in Turkey. The combustion process, and the design of the gas admission, pilot fuel, cylinder control, air-fuel control, and engine control and monitoring systems are described. The advantages of the engine are discussed.

Energy Technology Data Exchange (ETDEWEB)

The resistance to microbe damages of aqueous solutions of cutting fluids (SOZh), which contain dual and more complex mixtures of known compounds, is studied. Lauric acid, myristic and tridecanic acid give microbic resistance to the compositions of synthetic cutting fluids. A complexing of the compositions as a rule does not support precisely expressed effects of synergism or antagonism.

International Nuclear Information System (INIS)

The swelling behavior which results from simulated fusion environment irradiation of Fe-10% Cr has been characterized with transmission electron microscopy. Specimens were bombarded at 850 K with: a ''triple-beam'' of He"+, D_2"+, and 4 MeV Fe"+"+ ions to 0.3, 1, 3, 10, 30, and 100 dpa (displacement per atom); a ''dual-beam'' of He"+ and 4 MeV Fe"+"+ ions to 30 and 100 dpa; and a ''single-beam'' of 4 MeV Fe"+"+ ions to 30 dpa. The helium and hydrogen injection rates were approx. =10 appm He/dpa and approx. =40 appm D/dpa. Cavities were observed for damage levels of 3 dpa and greater. The swelling was <0.1% for damage levels <30 dpa, but at 100 dpa, there was an increase in the swelling to 2.5% for the ''triple-beam'' irradiation and 1.2% for the ''dual-beam'' irradiation. The swelling rates between 30 and 100 dpa correlate well with calculated values assuming a steady-state swelling-rate regime has been reached. Calculations show the ...

CERN Document Server

We define the Bloch spectrum of a quantum graph to be the collection of the spectra of a family of Schr\\"odinger operators parametrized by the cohomology of the quantum graph. We show that the Bloch spectrum determines the Albanese torus, the block structure and the planarity of the graph. It determines a geometric dual of a planar graph. This enables us to show that the Bloch spectrum completely determines planar 3-connected quantum graphs.

Energy Technology Data Exchange (ETDEWEB)

The membrane transport of the two stable lithium isotopes, {sup 6}Li and {sup 7}Li, by erythrocytes has been studied using a dual channel atomic absorption spectroscopic technique. {sup 6}Li appears to be taken up preferentially to {sup 7}Li, in the ratio of 10 to 40%, depending on the concentration of total lithium and on the lithium isotopic ratio in the external medium.

Wastenet

...to facilities using - Petrol and diesel industrial engines - Petrol and diesel light vehicles, commercial vehicles and trucks on the facility - Large stationary diesel and dual-fuel engines - Heavy-duty natural gas fired pipeline compressor engines and turbines First published in February 1999 Revised - August 2000 Version 2.3 - ...

Energy Technology Data Exchange (ETDEWEB)

MAN B&W in Augsburg, Germany has further developed its dual-fuel line of engines with the 32/40 DG engine family. These engines, with prechamber injection, augment the company`s spark-ignited gas and dual-fuel engines based on its four-stroke diesel engines. MAN B&W`s power range is between 400 and 16200 kW. Based on the well-proven 32/ 40 engine, the 32/40 DG dual-fuel engine was developed mainly for stationary applications in cogeneration plants and power stations, covering an output range from 2.4 to 7.2 MW. The engine line (bore 320 x stroke 400 mm) has a cylinder output of 400 kW at 750 r/min and a bmep of 19.9 bar with a maximum efficiency of 44.4%. The development focused on meeting TA Luft limits for NO{sub x} emissions of less than 500 mg/m{sup 3} NO{sub x}. This level was targeted without catalytic exhaust after treatment (SCR) and retaining high efficiency and high mean effective pressure similar to that ...

UK PubMed Central (United Kingdom)

Zn²⁺-finger proteins comprise one of the largest protein superfamilies with diverse biological functions. The ATM substrate Chk2-interacting Zn²⁺-finger protein...Full Text Available

International Nuclear Information System (INIS)

Several recently introduced 'new' techniques in computed tomography - iterative reconstruction, gated cardiac CT, multiple-source, and dual-energy CT - actually date back to the early days of CT. We review the historic origins and evolution of these techniques, which may provide some insight into the latest innovations in commercial CT systems. (orig.)

Energy Technology Data Exchange (ETDEWEB)

In this investigation natural gas has been used as an alternative fuel in diesel engines. Experiments have been performed to study the performance of the dual fuel engine with different diesel quantities as pilot injection. It was suggested in this research that combustion in the dual fuel engine occurred in four stages: the delay period, the slow stage of combustion, the rapid stage of combustion and the fourth stage of combustion. Because of the slower flame speed of natural gas and also because of the prolonged delay period, the combustion of the gas-air continued well into the expansion stroke. These resulted in lower efficiency and higher brake specific fuel consumption, and also higher exhaust gas temperature and higher carbon monoxide in the exhaust when the engine ran on dual fuel. The carbon dioxide and black smoke in the exhaust decreased as the gas was introduced in the engine. The ratio of alternative to diesel ...

British Library Electronic Table of Contents (United Kingdom)

Background and objectives.Thymidylate synthase (TS) expression levels appear to be related to response to 5-fluorouracil-(5-FU)-based chemotherapy in colorectal cancer (CRC) patients. Three polymorphisms have been proposed as modulators of TS expression: a tandemly repeated sequence (2R/3R) in the 5? UTR, a SNP (G > C) within the 3R allele and a 6 bp deletion in the 3' UTR.To evaluate the influence of TS expression and polymorphisms on clinical outcome of 5-FU-treated patients we performed a comprehensive genetic analysis on 63 CRC patients.Methods.TS expression levels were analyzed in normal and tumor tissues. TS coding sequence and UTR polymorphisms were investigated on DNA from normal tissue. LOH analysis was performed to determine tumor genotype.Results.A difference in disease-free sur...

Energy Technology Data Exchange (ETDEWEB)

Contents: expansion of pc mill application to plate mill and tandem cold mill; application of cluster type rolling mill (cr mill) for rolling of special steel (illustration); development of on-line roll grinding system with profile meter; development of new type jet pickling; new technology in continuous annealing furnace (illustration); anti-seismic testing system by 3-dimensional shaking table; development of mitsubishi hybrid desulfurization system; field performance of 500 mw advanced coal fired supercritical pressure operation boiler for unit no. 1 of tsuruga thermal power station, hokuriku electric power co., inc.; development of electronically controlled cylinder liner lubrication system for marine diesel engines; prediction technology on steady-state and transient performance of multi-air conditioners; a knowledge-based system approach to the autonomous piloting and navigation control of ships.

Energy Technology Data Exchange (ETDEWEB)

This paper presents a case study of site characterization and hydrocarbon contamination plume mapping/delineation in a gas processing plant in southern Mexico. The paper describes innovative and cost-effective use of passive (non-intrusive) and active (intrusive) techniques, including the use of compound-specific analytical methods for site characterization. The techniques used, on a demonstrative basis, include geophysical, geochemical, and borehole drilling. Geochemical techniques used to delineate the horizontal extent of hydrocarbon contamination at the site include soil gas surveys. The borehole drilling technique used to assess the vertical extent of contamination and confirm geophysical and geochemical data combines conventional hollow-stem auguring with direct push-probe using Geoprobe. Compound-specific analytical methods, such as hydrocarbon fingerprinting and a modified method for gasoline range organics, demonstrate the inherent merit and need for such analyses to properly ...

DEFF Research Database (Denmark)

Various MLM-type (M, medium-chain fatty acids; L, long-chain fatty acids) structured triacylglycerols were produced in pilot- or small-scale packed-bed reactors by lipase-catalyzed acidolysis. The incorporation and acyl migration of octanoic acid were measured by gas chromatography and Grignard degradation, and ranged from 39.0 to 48.7% and 0.6 to 9.3%, respectively. Quantitation of triacylglycerol molecular species was performed by ammonia negative ion chemical ionization (NICI) mass spectrometry (MS). The proportion of ACN (acyl carbon number) 34 species that contained one C-18 fatty acid and two C-8:0, in samples analyzed, varied from 12.5 to 23.2%. The selected regioisomers MLM and MML within the ACN 34 species group were quantified by NICI tandem MS (MS/MS) and were in the range of 97.1 to 98.4% and 1.6 to 2.9%, respectively. There was no correlation between the level of acyl migration during lipase-catalyzed esterification and the level of regioisomers of the ...

Energy Technology Data Exchange (ETDEWEB)

The Micro-strip Metal Foil Detectors (MMFD) designed and used for the Beam Profile Monitoring (BPM) are discussed. The results obtained for the MMFDs produced by different technologies are presented. The MMFD deposited onto the 20 {mu}m thick Si-wafer has been used for the BPM of the 32 MeV alpha-particle beam at the MPIfK (Heidelberg) Tandem generator. Another MMFD with totally removed Si-wafer at the working area has been applied for the on-line X-ray BPM at the HASYLAB (DESY). One may conclude that the developed technology of the micro-strip metal detector manufacturing allows to provide non-destructive measurement of X-ray intensity distribution over area of up to 50 mm{sup 2} with an accuracy of 10-20 {mu}m with a possibility of its improvement by a factor 5. A sub-micron position resolution is expected by applying electron lithography for the strip pattern production.

Energy Technology Data Exchange (ETDEWEB)

Electron cyclotron resonance (ECR) ion sources possess several advantages over ion sources conventionally used for injectors of electrostatic accelerators: improved reliability, high efficiency, simplicity, and the capability of generating bright, high-current ion beams. We have adapted a high-current ECR source originally developed as an injector for a CW RFQ proton linac to serve as a source of intense negative-ion beams for the Tandem Accelerator Superconducting Cyclotron (TASCC) facility at Chalk River. The range of ion species of the source has been extended from H{sup 1+} alone up to Bi{sup 1+}, with both gaseous and nonvolatile feeds. Two intense negative-ion beams of He{sup -} and O{sup -} have been generated so far with the source coupled to a standard charge-exchange canal. We foresee no major problems generating a broad range of negative ions with this system. (author)

Energy Technology Data Exchange (ETDEWEB)

A field study (1993-96) assessed the benefits of applying unusually high rates of coal fly ash from power plants as a soil amendment to enhance water retention of soils without adversely affecting growth and marketability of the turf species, centipedegrass (Eremochloa ophiuroides (Munro) Hack.) A Latin Square plot design was employed that included 0 (control, no fly ash applied), 280, 560 and 1120 MgHa {sup -1} application rates of unweathered precipitator fly ash. The fly ash was spread evenly over each plot area, rototilled, and allowed to weather under natural conditions for 8 months before seeding. High levels of soluble salts, indicated by the electrical conductivity of soil extracts, in tandem with an apparent phytotoxic effect from boron, apparently inhibited initial plant establishment as shown by substantially lower germination counts in treated soil. However, plant height and rooting depth were not adversely affected, as were the dry matter yields ...

Energy Technology Data Exchange (ETDEWEB)

At tandem cold rolling mills in Kawasaki Steel, by means of applying newly developed strip longitudinal (rolling) and transverse gauge control systems, high accuracy of thickness of within {+-}0.5 % has been achieved over the full length and full width of cold rolled strip, as gauge accuracy in a coil in longitudinal and transverse directions has become an extremely important quality control item in the manufacturing of cold rolled sheets due to the stricter quality requirements of customers, in recent years. The longitudinal gauge accuracy has been improved by the development of a high-response drive system for a mill mair motor, an all-stands gauge control system and a dynamic set-up control system. The transverse gauge accuracy has been improved by applying a one-side tapered work roll shifting method and the development of an edge drop control system in terms of the optimum use of an edge drop sensor. (author)

Energy Technology Data Exchange (ETDEWEB)

Together with an investigation on the deformation behavior of hot and cold rolled strip edge, the edge-drop control was explained in characteristics and result of application to the commercial mill by the tapered-crown work roll (WR) shifting mill. From a cold rolling experiment, three-dimensional material flow was known to be generated in the vicinity of edge also at the time of rolling the strip, and which generation influences that of edge-drop. Almost linearly relative to the flattened deformation of WR, the edge-drop enlarges with enlargement in that deformation. The number of stands to be applied to the tapered-crown WR shifting mill in the tandem cold mill is determined by the location as far as which the strip is to be controlled in edge-drop. In case of improving it to obtain the edge-drop-free strip, all the stands are required to be equipped with tapered-crown WR shifting mill. By applying a tapered-crown WR shifting mill to the latter stands for the hot ...

Energy Technology Data Exchange (ETDEWEB)

A generic reactor model is used to examine the economic viability of electricity generation by magnetic fusion. The simple model uses components which are representative of those used in previous reactor studies of deuterium-tritium burning tokamaks, stellarators, bumpy tori, reverse field pinches and tandem mirrors. Conservative costing assumptions are made. The generic reactor is not a tokamak but rather it is intended to emphasize what is common to all magnetic fusion reactors. The reactor uses a superconducting toroidal coil set to produce the dominant magnetic field. To this extent it is a less good approximation to systems, such as the reversed field pinch in which the main field is produced by a plasma current. The main output of the study is the cost of electricity as a function of the weight and size of the fusion core - blanket, shield, structure and coils. The model shows that a 1200 MW/sub e/ power plant with a fusion core weight of about 10,000 tonnes ...

Science.gov (United States)

We describe a method for affinity purification of sequence-specific DNA binding proteins that is fast and effective. Complementary chemically synthesized oligodeoxynucleotides that contain a recognition site for a sequence-specific DNA binding protein are annealed and ligated to give oligomers. This DNA is then covalently coupled to Sepharose CL-2B with cyanogen bromide to yield the affinity resin. A partially purified protein fraction is combined with competitor DNA and subsequently passed through the DNA-Sepharose resin. The desired sequence-specific DNA binding protein is purified because it preferentially binds to the recognition sites in the affinity resin rather than to the nonspecific competitor DNA in solution. For example, a protein fraction that is enriched for transcription factor Sp1 can be further purified 500- to 1000-fold by two sequential affinity chromatography steps to give Sp1 of an estimated 90% homogeneity with 30% yield. In addition, the use of ...

Science.gov (United States)

One of the NASA research activities was to identify, characterize, and simulate a series of technologies that could be used for hydrogen production at NASA Kennedy Space Center (KSC) using locally available sources. This project examined the production of hydrogen from solar energy. To produce hydrogen by water splitting, the operating voltage of conventional photovoltaic (PV) cells cannot supply the overvoltage required. Thus, the objective of this project was to research and develop photoelectrochemical (PEC) cells that can supply the required voltage for water splitting by constructing a multiple bandgap tandem PV cell and a photocatalyst that can be activated by infrared (IR) photons transmitted through the PV cell. The proposed concept is different from conventional PEC water splitting by using multiple band gap combinations. The advantages for this PEC cell concept is that the PV cells are not in contact with the electrolyte solution, thus reducing the ...

Energy Technology Data Exchange (ETDEWEB)

In the 80's, because of the oil crisis, the Natural Gas (NG) appeared as a fuel with a great potential for Diesel replacement in Heavy Duty Vehicles. At that time, PETROBRAS with other companies have developed partial conversion technologies from Diesel to NG, known as 'Dual Fuel'. Engine dynamometer and vehicle bus tests have been developed to verify its technical and economical viability. Because of several factors, the Dual Fuel Program did not advance and the experience was interrupted. At the same time, other experiences using NG Otto Cycle bus engines, manufactured in Brazil, have been conducted, mainly at Sao Paulo, nevertheless, without expansion. Currently, factors as increase of the NG converted light vehicles fleet; the NG excess in the National Market, which has contributed to the NG distribution net expansion; the Environmental Legislature in vigor, that continuously determine lower emission limits; the ...

International Nuclear Information System (INIS)

The two-phase flow regime transition in a large diameter (I.D.=200mm) vertical pipe was experimentally investigated using a dual-sensor optical probe. The flow transitions from bubbly to chum without an intermediate slug flow regime as the air flow rate is increased. The transition boundaries developed for bubbly to slug flow in small diameter pipes are compared to the bubbly to chum flow transition of the present experiment. The bubbly to chum transition occurs at a void fraction of about 0.15 compared to 0.25 for bubbly to slug transition in small diameter pipes. The radial distribution of bubble diameter, bubble frequency, bubble velocity and local void fraction were obtained using a dual-sensor optical probe at different flow conditions. The Probability Density Function (PDF) and Cumulative Distribution Function (CDF) of the bubble velocity and size are used to study the flow regime transition in the large diameter pipe. (author)

Energy Technology Data Exchange (ETDEWEB)

By retrofitting the existing steam turbine dual purpose power plant with a gas turbine plant and a secondary waste heat boiler the Technische Werke Ludwigshafen AG have considerably improved the energy generation in energetic, economic and ecological terms. The extension of the existing system to a combined cycle process has lead to this positive effect. The erection of a boiler plant during the first two construction phases has fully met the optimistic expectations. (orig.) [Deutsch] Mit der Nachruestung eines vorhandenen Dampfturbinen-HKW um eine Gasturbinenanlage mit nachgeschaltetem Abhitzekessel haben die Technischen Werke Ludwigshafen AG ihre Energieerzeugung entscheidend in energetischer, oekonomischer und oekologischer Sicht optimiert. Insbesondere die Erweiterung des vorhandenen Systems zu einem GuD-Prozess fuehrt zu dieser positiven Bilanz. Die Errichtung der Kesselanlage in den ersten beiden Bauabschnitten hat die optimistischen Erwartungen voll ...

Science.gov (United States)

Fetal exposure to phthalates may be associated with adverse reproductive effects, including cryptorchidism and decreased semen quality. Information about human placental transfer is needed to qualify the hypotheses. A dual recirculating placenta perfusion system to monitor concentrations of eight phthalate monoesters in fetal and maternal perfusates was established. In addition to perfusate background measures of phthalate monoesters, the concentrations in umbilical cord plasma and placenta tissue were measured. Monomethyl phthalate (mMP), monoethyl phthalate (mEP), monobutyl phthalate (mBP), and mono (2-ethyl-hexyl) phthalate (mEHP) were detected in both maternal and fetal perfusate, demonstrating a release of compounds from tissue or blood to perfusates. The distribution of compounds between perfusate, umbilical cord plasma, and tissue was in accordance with the physical-chemical properties of the compounds. Results from the present study of compounds residing in ...

Energy Technology Data Exchange (ETDEWEB)

The latest electronic circuit technology that can be used for the electric railway traction system fed by an AC/DC dual power line was developed. This system consists of reverse conducting GTO thyristors, microprocessors, and DSP`s. In the AC power supply line section, the line converter is controlled by PWM technology to secure a high power factor and reduce the higher harmonic generation of an input current as far as possible. The line converter and motor converter use reverse conducting GTO thyristors. Since these converters are cooled using a heat pipe cooler, they are reduced in size and weight. The electric grounding point of the main power circuit is set to the negative side of the DC line for AC and DC line sections. Therefore, the AC/DC selector switch was simplified in structure. Moreover, the DC input for the auxiliary power supply can be obtained from multiple line converters using diodes. As the result of the actual operational test, the expected ...

CERN Document Server

Gravitational lensing by the dual cusp catastrophes of the cold dark matter (CDM) caustic rings at cosmological distances may provide the tantalizing opportunity to detect CDM indirectly, and discriminate between axions and weakly interacting massive particles (WIMPs). Caustics are places where the CDM particles are naturally focussed. Our focus is upon the caustic rings which are closed tubes whose cross-section is an elliptic umbilic catastrophe with three dual cusps. A caustic ring has a specific density profile, a specific geometry and, therefore, precisely calculable gravitational lensing signatures. The magnification monotonically increases as the line of sight approaches to the cusps where it diverges in the limit of zero velocity dispersion. In this limit, we find 37% magnification at a sample point near the outer cusps of the CDM caustic rings at cosmological distances. In the presence of finite velocity dispersion, the lower and upper ...

Energy Technology Data Exchange (ETDEWEB)

This report describes results from emissions testing of a prototype diesel engine, developed by Volvo Truck Corporation of Sweden, which uses pilot injection of diesel fuel for compression ignition of alcohol fuel injection for main combustion. In addition to this dual-fuel engine, emission testing was also conducted on a heavy-duty diesel engine of similar design. Both engines were tested over the 1979 13-mode FTP, or shorter versions of this modal test, and over the 1984 Transient FTP as well as an experimental bus cycle. The dual-fuel engine was characterized with methanol, ethanol and ethanol with 30 percent water (wt %). An oxidation catalyst was also used with methanol and ethanol. Emission characterization included regulated emissions (HC, CO, and NOX) along with total particulate, unburned alcohols, individual hydrocarbons, aldehydes, phenols, and odor. The particulate matter was characterized in terms of particle size distribution, ...

International Nuclear Information System (INIS)

The synergistic effects of displacement damage and atomic hydrogen and helium on swelling of the ferritic/martensitic steel, F82H, has been investigated. The irradiation was performed at temperatures between 470 and 600 deg. C to 50 dpa (displacement per atoms) under conditions of simultaneous ion beams consisting of Fe"3"+, He"+ and H"+ ions or Fe"3"+ and He"+ ions. The swelling of F82H steel under triple beams with 18 appm He/dpa and 70 appm H/dpa was larger than that under dual beams with 18 appm He/dpa. The swelling in F82H under triple beams increased with decreasing irradiation temperature from 0.1% to 3.2%, while swelling under dual beams was between 0.04% and 0.08%. On the other hand, in the case of triple beam irradiation with a high ratio of gas/dpa, the swelling tended to increase with irradiation temperature. The swelling in ferritic/martensitic steels is significantly enhanced by the synergistic effect of displacement damage, ...

International Nuclear Information System (INIS)

Based on a recently introduced phase X-ray imaging approach, a dual-detector prototype was developed for in-line X-ray phase imaging and phase retrieval utilizing a micro-focus X-ray source and two computed radiography (CR) cassette detectors. The system was built on a horizontal optical rail to facilitate manual adjustment of the positions of the X-ray source, the sample and the detectors. The novel design of the detector-1 is essential, it detects a portion of radiation to form an attenuation image; allows the rest of radiation to reach the detector-2 to form a phase contrast image, and the two images are used to retrieve a phase map. The two detectors are balanced for optimal phase-retrieval with reasonable radiation dose to the object to be imaged. The system was examined in terms of the linearity, the fractions of the X-ray photons detected by the two detectors, respectively and the imaging quality of phantoms. Preliminary results showed that the system is ...

International Nuclear Information System (INIS)

The localized Pt deposition on Si by 30 keV Ga"+ focused ion beam (FIB), 10 keV electron beam (EB) or dual beams (FIB and EB) using precursor gas has been compared by analysis using a 300 keV Be"2"+ microprobe with a beam spot size of 80 nm. The distribution of deposited Pt, Ga from the ion beam itself, and C from the precursor gas was obtained at and nearby the deposited areas by micro-RBS spectra and RBS mapping. All of the beam processed areas showed a uniform Pt distribution at the deposited areas. The amount of Pt atoms increased with the increase in ion or electron dose due to the decomposition of precursor gas. The thickness of Pt layer by EB is considerably less than that by FIB due to the reduced deposition rate. Ga atoms from the center of processed areas partly redeposited at and nearby the FIB processed areas within #approx#3 #mu#m. The Ga incorporation by dual beam processing was reduced compared with that by FIB processing. The ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes in an dual gas-liquid fuel four cycle engine having cylinders and wherein each cylinder is operatively connected thereto and each cylinder has a piston, two inlet valves, two exhaust valves and a first liquid fuel injector. It comprises: at least one fuel torch cell operatively connected to at least one cylinder, the torch cell having a torch cell nozzle at one end thereof and the other end having appropriate means to connect the torch cell to a fuel supply, a second fuel injector mounted in the torch cell at a predetermined angle to an axis of the torch cell, the torch cell defining an auto-ignition chamber, the second fuel injector being in operative communication with the auto-ignition chamber by an injector nozzle passageway, the injector nozzle passageway entering the auto-ignition chamber at a predetermined angle relative to the axis, and a torch nozzle passage connecting the auto-ignition chamber with the cylinder at a predetermined ...

Energy Technology Data Exchange (ETDEWEB)

This paper investigated the effect of hydrogen (H{sub 2}) addition on the combustion process of a heavy-duty diesel engine. The addition of a small amount of H{sub 2} was shown to have a mild effect on the cylinder pressure and combustion process. When operated at high load, the addition of a relatively large amount of H{sub 2} substantially increased the peak cylinder pressure and the peak heat release rate. Compared to the two-stage combustion process of diesel engines, a featured three-stage combustion process of the H{sub 2}-diesel dual fuel engine was observed. The extremely high peak heat release rate represented a combination of diesel diffusion combustion and the premixed combustion of H{sub 2} consumed by multiple turbulent flames, which substantially enhanced the combustion process of H{sub 2}-diesel dual fuel engine. However, the addition of a relatively large amount of H{sub 2} at low load did not change the two-stage heat release ...

Energy Technology Data Exchange (ETDEWEB)

A sequential port injection, lean-burn, fully electronically-controlled compressed natural gas (CNG)/diesel dual-fuel engine has been developed based on a turbo-charged and inter-cooled direct injection (D.I.) diesel engine. During the optimisation of engine overall performance, the effects of pilot diesel and premixed CNG/air mixture equivalence ratio on emissions (CO, HC, NO{sub x}, soot), knocking, misfire and fuel economy are studied. The rich and lean boundaries of the premixed CNG/air mixture versus engine load are also provided, considering the acceptable values of NO{sub x} and THC emissions, respectively. It is interesting to find that there is a critical amount of pilot diesel for each load and speed point, which proved to be the optimum amount of pilot fuel. Any decrease in the amount of pilot diesel from this optimum amount results in an increase of NO{sub x} emissions, because the premixed CNG/air mixture must be made richer, otherwise THC emissions ...

Energy Technology Data Exchange (ETDEWEB)

There is presently considerable interest in wear resistant coatings produced using closed field unbalanced magnetron sputtering technology. For example, layered films of diamond-like carbon (DLC) with tungsten or titanium additions have been widely reported. The benefit is that the mechanical properties are enhanced (e.g. giving greater toughness); also it is possible to control the stress state and enhance adhesion. Here we report the further development of this concept by the addition of TiN, TiCN and TiC layers in DLC-based composites, utilizing an additional source of electrons in the vicinity of substrate to enhance ionisation of the plasma and increase coating density. Composite coatings of ceramics TiN, TiC{sub x}N{sub y}, TiC, CrN, TiCrN, TiCrCN, TiCrC, metal doped Ti{sub x%}-DLC and their combinations were deposited on 316 stainless steel substrates. The mass flow of reactive gases into the chamber was controlled using plasma optical emission monitoring to achieve the desired ...

Energy Technology Data Exchange (ETDEWEB)

The topics of these short lectures on the subject of cyclic stress were: Microstructural mechanisms of damage accumulation under a multistage cyclic stress until incipient cracking; influence of surface decarbonizing phenomena on the failure behaviour of steel construction parts subjected to cyclic stress; thermocyclic fatigue of pipe samples of austenitic steel 1.4436; studies on surface structuring, microstructure and fatigue in LCF area. The short lectures on effects of quasi-static and creep stress were: Shear fracture in AlMg alloys as a result of local plastic instability; study of formation and growth of pores for an early recognition of damage and the course of damage in heat-resistant steels under creep test; experimental and numeric studies of the infuence of the microstructure on the course of damage during shear fractures of steel; numerical modelling of ductile fractures on the basis of micromechanical models. Under the topic of tribological stress the following lectures ...

Energy Technology Data Exchange (ETDEWEB)

The reduced polluting emissions make natural gas a quite interesting alternative fuel for automotive applications. Therefore a car diesel engine has been transformed into a dual fuel engine with pilot injection via the common rail injection system used to ignite the methane-air charge. Standard injection pumps show a certain instability at low flow rates and high engine speed. On the opposite the new common rail system allows to ignite the fuel in all conditions with an amount of gas oil less than 8% of the entire energy required by the engine was enough to ignite the fuel. Furthermore, a power increase has been obtained, with an overall efficiency equal to or even higher than a conventional engine. The article deals with a series of test carried out on 1929 cm{sup 3} direct injection turbo-charged engine and presents the preliminary results. [Italian] La riduzione delle emissioni inquinanti rende il metano un combustibile alternativo piuttosto interessante per ...

Energy Technology Data Exchange (ETDEWEB)

A self contained continuous power generation system as described at INTELEC 1979, was successfully commissioned and put into service in a major communications centre at Cardiff in Wales. The objective was to provide all telecommunications equipment and electrical building engineering services from a dual fuel enginegenerating plant, and to recover waste heat energy to heat or cool the building. The plant, which is fully automatic, comprises five 1300kW engines using natural gas or diesel oil, and associated waste heat boiler and chiller systems. This paper reviews the functioning of the plant during its first three years of operation.

CERN Document Server

The whole computer hardware industry embraced multicores. For these machines, the extreme optimisation of sequential algorithms is no longer sufficient to squeeze the real machine power, which can be only exploited via thread-level parallelism. Decision tree algorithms exhibit natural concurrency that makes them suitable to be parallelised. This paper presents an approach for easy-yet-efficient porting of an implementation of the C4.5 algorithm on multicores. The parallel porting requires minimal changes to the original sequential code, and it is able to exploit up to 7X speedup on an Intel dual-quad core machine.

Energy Technology Data Exchange (ETDEWEB)

Non-Abelian duality in relation to supersymmetry is examined. When the action of the isometry group on the complex structures is nontrivial, extended supersymmetry is realized nonlocally after duality, using path-ordered Wilson lines. Prototype examples considered in detail are, hyper-Kahler metrics with SO(3) isometry and supersymmetric WZW models. For the latter, the natural objects in the nonlocal realizations of supersymmetry arising after duality are the classical non-Abelian parafermions. The canonical equivalence of WZW models and their non-Abelian duals with respect to a vector subgroup is also established. {copyright} {ital 1996 The American Physical Society.}

Energy Technology Data Exchange (ETDEWEB)

Apparatus and a method of introducing a primary fuel, which may be a coal water slurry, and a high combustion auxiliary fuel, which may be a conventional diesel oil, into an internal combustion diesel engine comprises detecting the load conditions of the engine, determining the amount of time prior to the top dead center position of the piston to inject the main fuel into the combustion chamber, and determining the relationship of the timing of the injection of the auxiliary fuel into the combustion chamber to achieve a predetermined specific fuel consumption, a predetermined combustion efficiency, and a predetermined peak cylinder firing pressure. 19 figures.

International Nuclear Information System (INIS)

In order to achieve the safe core cooling during normal operation and upset conditions, HANARO adopted an upward forced convection cooling system with dual containment arrangements instead of the forced downward flow system popularly used in the majority of forced convection cooling research reactors. This kind of upward flow system was selected by comparing the relative merits of upward and downward flow systems from various points of view such as safety, performance, maintenance. However, several operational matters which were not regarded as serious at design come out during operation. In this paper are presented the design and operational experiences on the unique cooling features of HANARO. (author)

Energy Technology Data Exchange (ETDEWEB)

Recent industry advances in formation evaluation measurement-while-drilling (FEMWD) have been achieved in well log data acquisition quality and in geosteering drilling applications. This paper presents new technology as applied by Baker Hughes INTEQ which includes: geosteering techniques which help navigate through horizontally drilled reservoirs including improved quality dual propagation resistivity, neutron-porosity and formation-density measurements; predictive modeling of tool responses in reservoir geosteering applications; environmental computer modeling which aids interpretation, including tool eccentering; and new measurement enhancements.

Energy Technology Data Exchange (ETDEWEB)

Starting with two supersymmetric dual theories, we imagine adding a chiral perturbation that breaks supersymmetry dynamically. At low energy we then get two theories with soft supersymmetry-breaking terms that are generated dynamically. With a canonical K{umlt a}hler potential, some of the scalars of the ``magnetic`` theory typically have negative mass-squared, and the vector-like symmetry is broken. Since for large supersymmetry breaking the ``electric`` theory becomes ordinary QCD, the two theories are then incompatible. For small supersymmetry breaking, if duality still holds, the magnetic theory analysis implies specific patterns of chiral symmetry breaking in supersymmetric QCD with small soft masses.

Energy Technology Data Exchange (ETDEWEB)

Some recent achievements in the field of high pressure vessels and safety devices have offered a concrete chance to the application of compressed hydrogen for fleet commercial vehicles for urban use. Accordingly with this concept, ENEA has modified a Fiat Ducato van with a dual fuel engine, retaining the gasoline tank for long distance travelling and adopting the external mixture formation technique, with hydrogen injectors developed by ENEA, for non-polluting short-range duties in urban traffic. The article deals with the rationale for this choice and gives a general view of the project. (author)

Science.gov (United States)

BAE Systems is the leading producer of uncooled microbolometer based thermal imaging engines in the world. Initial investments to develop and produce uncooled infrared (IR) technology were primarily driven by military applications, but it was the commercial market with the potential for large product volumes which provided BAE Systems with the business model required for investment in uncooled IR technology. This paper reviews the heritage of BAE Systems technology and current products and is an example of the success of a Dual-Use technology area which DARPA invested in during the 1990s.

Energy Technology Data Exchange (ETDEWEB)

Dual energy X-ray absorptiometry (Hologic QDR-1000) was used to quantitatively analyze the diagnosis and prevention of osteoporosis. The peak bone mineral density (BMD) of the spine appeared in normal men in their twenties and in normal women in their thirties. There was acceleration of bone loss in the 50 to 60 year age bracket (premenopause and postmenopause) in normal women. On the contrary, the peak BMD of the femoral neck in normal men and women appeared in their twenties after which it decreased slightly with age. Comparison showed that the femoral neck BMD of normal women was lower than that of men throughout all ages. The fracture threshold, 0.756 g/cm[sup 2] for the spine, was obtained by scanning 73 females with spinal fractures, the mean BMDs for L2-L4 at the 90th percentile level were used as the fracture threshold. The fracture threshold of femoral neck fracture was the femoral proximal BMD of the 9th decile. Classification by the Public Welfare Silver ...

Energy Technology Data Exchange (ETDEWEB)

Nanometre-sized materials, like nanowires, nanoparticles or nanobelts, are gaining huge interest as building blocks of modern electronic nanodevices. Their fabrication feasibility has been demonstrated in the last years, and different routes are already well established in order to synthesize these materials. However, the assessment of their electrical properties is still a challenging issue, due to the difficulty to perform a precise nanolithography process allowing the access to such small structures. The fabrication of metallic contacts with precision in the nanometre range is necessary, as well as achieving a flexible system that allows to contact individual structures. Such a system could be a dual-beam Focused Ion Beam instrument, which combines Scanning Electron Microscopy (SEM) and Focused Ion Beam (FIB) in one machine, able to assist deposition of materials with nanometre precision. In this work, the methodology of fabrication of metallic nanocontacts to ...

Energy Technology Data Exchange (ETDEWEB)

In light of the recent rapid increase in the fossil fuel prices it is meaningful to evaluate the impact of these price changes in the economics of dual-purpose desalination projects producing electricity and fresh water simultaneously. The price of crude oil and LNG (Liquefied Natural Gas) has increased by about 200% and 100% during the past three or four years. The uranium price has also increased by nearly 500% during the same period. The purpose of this paper is to analyze and compare the economics of SMART (System-integrated Modular Advanced ReacTor) which is being developed as a small size PWR type and the LNG Combine Cycle coupled with MED (Multi-Effect Distillation) which are being acknowledged as promising energy sources for the future in Korea. The methods of analysis used in this paper are the lifetime leveled cost method for the power and water cost calculation and the power credit method for the total cost allocation. DEEP (Devaluation Economic ...

International Nuclear Information System (INIS)

Objective: To discuss the clinical application value of dual energy subtraction (DES) in direct digital radiography of chest. Methods: 83 cases of chest digital radiography(DR) using double-energy subtraction (DES) were randomly selected, and three posterior-anterior (PA) chest films (standard image, bone image and soft tissue image) were obtained in each case, which is so called 'bone and soft tissue separated' technology. Results: With the aid of double energy subtraction (DES), the bony chest was subtracted, the sensitivity and specificity of pulmonary calcification were improved, and sensitivity of pulmonary nodes was also improved, enhancing the distinction between pulmonary benign or malignant lesions, enlightening the diagnosis of chest cage lesions, and showing a clear superiority in the detection of pulmonary nodes comparing to common chest films. The double energy subtraction (DES) films showed a higher diagnostic accuracy in the detection of bony cage ...

Energy Technology Data Exchange (ETDEWEB)

The first commercial vehicle, built by Gottlieb Daimler in Cannstatt (Germany), head foto, had been the begin of a new transport technology around the world. Benz had been consolidated 1926 with Daimler to the Daimler-Benz AG with a new vehicle programme; all trucks over 5 t payload would be powered since 1935 by diesel engines only. Worldwide all-wheel drived vehicles had been under development for different purposes. After 1945 the European Automobil industry launched at first former types followed by new designed and improved types. The eight-wheeler used since the twentees in England conquered Switzerland, and in 1984 Germany too. The development of gear boxes and drive axles had been influenced on the drive train demands depending of the engine output and speed and the increased GTW. The future of the commercial vehicles will be determined by the European legislation, higher economy and reduced-pollutant Euro II and later Euro III engines, further by the ...

CERN Document Server

We prove, using the AdS/CFT correspondence, that the long wavelength dynamics of the shear stress tensor in a strongly coupled N=4 SYM plasma is not described by the relaxation-type, fluid dynamical equations proposed by Israel and Stewart: the coarse grained dynamics will necessarily contain a second-order comoving derivative of the shear stress tensor. We argue that this should be true for any strongly-coupled gauge theory with a gravity dual. If the QGP formed in heavy ion collisions can indeed be described in terms of a (yet unknown) theory of gravity in higher dimensions, the equations of motion used in hydrodynamical simulations of the QGP must necessarily include second order comoving derivatives of the shear stress tensor.

British Library Electronic Table of Contents (United Kingdom)

Thyroid cancer is the most frequently diagnosed endocrine cancer and causes more deaths than all other endocrine cancers combined. Research findings support the concept that a subpopulation of thyroid cancer cells displays properties characteristic of stem cells. These putative cancer-forming entities drive tumorigenesis as a result of their dual ability to undergo self-renewal and to differentiate into various types of cancer cells; they also mediate metastasis and are resistant to the effects of chemotherapy and radiation therapy. This Review discusses the cellular origin of thyroid cancer and the properties of the thyroid cancer stem cell niche. The article critically evaluates the methods used to identify molecular markers expressed by thyroid-cancer-initiating cells and outlines prosp...

British Library Electronic Table of Contents (United Kingdom)

The main goal of local drug delivery is to increase the concentration of a specific therapeutic agent in a target tissue with minimal nontarget distribution. Compared to systemic therapy, local drug delivery provides a high level of therapeutic efficacy with minimal systemic effects. The current primary imaging modality for drug delivery has been x-ray angiography, but it has major limitations including anatomical ambiguity and inability to visualize the targeted tissues. Due to these inherent problems, MR guidance has been explored as an alternative imaging modality for guiding and monitoring of drug therapy. Recently, interventional MR (XMR) systems have been implemented that have both dual x-ray and MRI capabilities in a single suite and allow for real-time interventional procedures to ...

Energy Technology Data Exchange (ETDEWEB)

The energy level schemes of /sup 192/Os and /sup 192/Pt have been established on the basis of ..gamma..-..gamma.. coincidence studies using a dual parameter data collection system. Ge(Li) detectors were employed to study the gamma spectra produced in the E.C. and ..beta../sup -/ decays of /sup 192/Ir to /sup 192/Os and /sup 192/Pt, respectively. Thirteen new transitions and three new levels at 1146.95, 1237.35 and 1913.76 keV are suggested. Relative intensities from singles measurements, branching ratios, ..cap alpha..(K) and log ft values were calculated and multipolarities, spins and parities deduced. Comparisons are made with predictions of the Interacting Boson Model calculated on the basis of an O(6) to SU(3) transition.

CERN Document Server

We study general two-dimensional sigma-models which do not possess manifest Lorentz invariance. We show how demanding that Lorentz invariance is recovered as an emergent on-shell symmetry constrains these sigma-models. The resulting actions have an underlying group-theoretic structure and resemble Poisson--Lie T-duality invariant actions. We consider the one-loop renormalization of these models and show that the quantum Lorentz anomaly is absent. We calculate the running of the couplings in general and show, with certain non-trivial examples, that this agrees with that of the T-dual models obtained classically from the duality invariant action. Hence, in these cases solving constraints before and after quantization are commuting operations.

Energy Technology Data Exchange (ETDEWEB)

The dual characteristics in the performance of polymers in wood-polymer composites systems have been pursued with regard to the resolution of mechanical anisotropy of wood and the improvement in dimensional stability. The objective of the present study is to pursue the polymerization mechanism in wood under electron beam irradiation and the temperature dependence of polymer-wood interactions induced at various levels of higher order structure of wood in order to understand the polymer performance. Veneers used in the study were of rotary-cut beech (Fagus crenata Blume) 0.65 mm thick. All samples were oven-dried in vacuo at 80/sup 0/C for 30 hr. The monomers used in the study were methyl methacrylate, styrene, acrylic acid, acrylonitrile, and unsaturated polyester. Experimental details are given. Results are given and discussed.

International Nuclear Information System (INIS)

Photocurrent and capacitance measurements of semiconductor passive films formed on metals and alloys can be used to study the electronic properties and reveal indirect information about structure and composition. The current work used these techniques to investigate the electronic properties of the passive films formed on three austenitic stainless steels, types 304L, 316L and 254SMO, in borate. Evidence was found for the existence of a large number of localised mid bandgap states, consistent with amorphous oxides. However, the flat-band potentials of the austenitic stainless steel passive films were found to be independent of both composition and measuring frequency. The most credible explanation for the bandgap values determined from photocurrent measurements is that the passive films are formed as dual layers, iron oxide outer layer and chromium oxide inner layer. This model does not need to evoke the potential dependent bandgaps used by previous authors.

British Library Electronic Table of Contents (United Kingdom)

Samples of Fe78B13Si9 (Metglas 2605 TCA) and Fe77Cr2B16Si5 (Metglas 2605 S3A) were exposed to pulsed excimer laser irradiation at repetition rates of 15, 25 and 50Hz. The occurrence of out-of-plane magnetic anisotropy, changes in the average hyperfine magnetic field and width of the hyperfine field distribution were evidenced by transmission Mossbauer spectroscopy. The variation of the recoilless fraction with laser processing parameters was derived from the simultaneous recording of Mossbauer spectra using a stainless steel etalon as a dual absorber. Conclusions on the onset of long-range magnetic order were formulated.

Energy Technology Data Exchange (ETDEWEB)

A 1 MWe power plant using waste wood fuel is to be installed at a US Marine Corps base, which will supply all wood from a landfill site. The core energy conversion technology is a down-draft gasifier supplying approximately 150 Btu/scf gas to both spark ignition and diesel dual-fuel engine-generator sets. Features of the plant design include: (1) grinding wood fuel from a wide range of waste resources, (2) specialized screening for fines removal, (3) complete tar and other waste product control without landfill disposal, and (4) use of process heat for bulk fuel drying, gasifier air pre-heating, and wastewater evaporation.

Energy Technology Data Exchange (ETDEWEB)

While it is difficult to prove that a specific material is causing contamination in a landfill, tests have been conducted at waste-to-energy facilities that indicate that household batteries contribute significant amounts of heavy metals to both air emissions and ash residue. Hennepin County, MN, used a dual approach for developing and implementing a special household battery collection. Alternative collection methods were examined; test collections were conducted. The second phase examined operating and disposal policy issues. This report describes the results of the grant project, moving from a broad examination of the construction and content of batteries, to a description of the pilot collection programs, and ending with a discussion of variables affecting the cost and operation of a comprehensive battery collection program. Three out-of-state companies (PA, NY) were found that accept spent batteries; difficulties in reclaiming household batteries are ...

International Nuclear Information System (INIS)

Polycrystalline specimens of spinel (MgAl_2O_4) and alumina (Al_2O_3) were irradiated at room temperature and 650deg C with either dual- or triple-ion beams in order to investigate the effects of simultaneous displacement damage and helium implantation on cavity formation. The cavities in alumina were aligned along the direction of the c-axis, with diameters ranging from < 2 to 10 nm. The cavities in spinel were preferentially associated with dislocation loops and were of similar size as the cavities in alumina. Catastrophic amounts of cavitation were observed at the grain boundaries in spinel when the displacement damage level exceeded a critical value (#approx =# 20 dpa) in the presence of a fusion-relevant (#approx =# 60 appm/dpa) helium environment. (orig.).

British Library Electronic Table of Contents (United Kingdom)

Abstract Green tea extract showed false-negative results in the determination of glucose via glucose oxidase (GOD) test. This investigation was undertaken to verify and find out the precise mechanism underlying this interference by determining the reaction kinetics of production and reduction of end-point chromophore. The peroxidase step of the GOD test was found to be interfered and phenols of the green tea were the interfering compounds. Green tea interfered and exerted its influence in a dual fashion. A part of the interference was observed as a result of the reduction of the finally formed chromophore, whereas the other form of interference was due to its hydrogen peroxide/free radical-scavenging activity. Reducing potential and the free radical-scavenging activity of the phenols in th...

International Nuclear Information System (INIS)

An iterative phase retrieval algorithm was previously investigated for in-line x-ray phase imaging. Through detailed theoretical analysis and computer simulations, we now discuss the limitations, robustness, and efficiency of the algorithm. The iterative algorithm was proved robust against imaging noise but sensitive to the variations of several system parameters. It is also efficient in terms of calculation time. It was shown that the algorithm can be applied to phase retrieval based on one phase-contrast image and one attenuation image, or two phase-contrast images; in both cases, the two images can be obtained either by one detector in two exposures, or by two detectors in only one exposure as in the dual-detector scheme.

Energy Technology Data Exchange (ETDEWEB)

Rice husk generated as a by-product of rice processing is an important energy resource. The availability of this resource in India has been assessed and the technologies for exploitation of its energy potential in rice processing industry discussed. Nomographs have been developed for estimation of the husk required to meet the energy demand of parboiling, drying and milling operations. The unit cost of electricity using rice husk gasifier-based power generation systems has been calculated and its financial feasibility assessed in comparison with utility-supplied and diesel-generated electricity. With the cost and efficiency data assumed here, the unit cost of electricity produced by rice husk gasifier-dual fuel engine-generator system varies between Rs 2/kWh and Rs 7/kWh. (author)

International Nuclear Information System (INIS)

AISI 5140 steel was plasma nitrided at various gas mixtures of nitrogen, hydrogen, and argon to investigate the actions of hydrogen and argon on plasma nitriding. The structural and mechanical properties of ion-nitrided AISI 5140 steel have been assessed by evaluating composition of phases, surface hardness, compound layer thickness, and case depth by using X-ray diffraction (XRD), microhardness tests, and scanning electron microscopy (SEM). It was found that the growth of compound layer can be controlled and the diffusion improved when the gas mixture includes H_2 gas. Additionally, it was determined that the amount of Ar in dual gas mixture must be at 20% minimum to obtain distinctive surface hardness and compound layer thickness.

Energy Technology Data Exchange (ETDEWEB)

This paper presents the current status and future prospects of rocket propellants and the development of rocket engines. The combinated rocket propellant of liquid oxygen (LO/sub 2/) and liquid hydrogen (LH/sub 2/) is so much effective that it is typically used for the main engine of the space shuttle of the U.S. LE-7 engine with the thrust output of 100 tons is being developed for H-2 launcher following H-1 launcher in Japan. Meanwhile, HM-60 engine is being developed for ARIANE-5 launcher in Europe. Although the LO/sub 2//LH/sub 2/ engine predominates in this field at present, a dual fuel engine combining LO/sub 2//LH/sub 2/ and LO/sub 2//hydrocarbon will be realized in near future. The fuel such as LNG (methane) and LPG (propane) will be used for rocket and ramjet engines. (10 refs, 2 figs, 3 tabs)

International Nuclear Information System (INIS)

Purpose: To prevent structure material meltdown upon rupture of cooling pipeways in a impurity remover by preventing the coolants from flowing into the vacuum vessel while continuing the supply of coolants to other portions to be cooled. Constitution: Dual cooling pipeway systems are disposed to the neutralizing plates of the impurity remover. A rupture detector (pressure gage) is mounted to each of the cooling pipeways and flow rate control valves to be opened and closed by the signal from the detector are disposed to the upstream and downstream of the cooling pipeway. In this constitution if the cooling pipes should be ruptured, the coolant supply is stopped to the ruptured system in which the flow rate valve is closed by the signal from the rupture detector. However, since the coolant is kept to be supplied to the other system of the cooling pipeways, meltdown of the neutralizing plates can be prevented. (Kamimura, M.).

Energy Technology Data Exchange (ETDEWEB)

Solar cells consisting of polymer layers sandwiched between a transparent electrode on glass and a metal top electrode are studied using dynamic time-of-flight secondary ion mass spectrometry (TOF-SIMS) in dual-beam mode. Because depth profiling of polymers and polymer-metal stacks is a relatively new field the craters were thoroughly investigated by environmental SEM (ESEM), interferometry, surface profilometry and tapping mode AFM. A huge increase in crater bottom roughness was observed when starting from the aluminum top layer going in depth, resulting in a loss of depth resolution. It is shown that layer-to-layer diffusion and contaminants at buried interfaces can be extracted from the depth profiles when taking into account the loss of depth resolution.

Energy Technology Data Exchange (ETDEWEB)

Examination is made of the main features of the physical and chemical preignition processes within homogeneous mixtures of air and gaseous fuels, such as propane, methane and hydrogen in a motored engine, while employing detailed chemical kinetics in a one zone analytical model. The changes in the compression temperature and pressure due to the admission of gaseous fuels, energy release during the preingition reactions and the contributions of heat transfer and residual gases to the preignition reaction activity were followed over a number of consecutive cycles until the occurrence of autoignition. Some of the observed differences in engine behaviour when operating on methane, propane and hydrogen were discussed with particular reference to the observed trends in dual fuel engine operation. Calculated results showed good agreement with some corresponding experimental trends. 14 refs., 9 figs.