Microstructure of c-BN films deposited by IBAD: IR and HREM analyses
International Nuclear Information System (INIS)
The in-depth distribution of phases in c-BN films deposited by Ion Beam Assisted Deposition (IBAD) at two different ion energy values (300 and 600 eV) was investigated using the quantitative IR transmission measurements and the HREM technique. Whatever the value of the studied ion energies, the characteristic layered morphology of c-BN film is observed including the interfacial sp"2 zone between the substrate and the c-BN volume. In the case of 600 eV ion energy, this interfacial zone is less well-defined in comparison with 300 eV ion energy and the corresponding thickness is more important. Furthermore, the h-BN phase is more diluted within the c-BN film volume showing that the purest phase concentration of c-BN is found for the lowest ion energy, i.e., 300 eV.
1997-04-04
Adsorption properties of #alpha#-modification of boron nitride
International Nuclear Information System (INIS)
The adsorption properties of four samples of the #alpha#-modification of boron nitride (#alpha#-BN) were investigated by the gas-chromatographic method. According to the electron microscopy data, the #alpha#-BN particles possess the shape of thin plates. An #alpha#-BN sample prepared from magnesium polyboride, is the most uniform adsorbent. For a series of n-alkanes, benzene, and alkyl benzenes, by testing the #alpha#-BN samples one has obtained the retained volumes (Henry constants) and the values of the differential adsorption heat, which are close to those of the surface zero filling. These thermodynamic characteristics of adsorption have shown that the #alpha#-BN, line the graphitized thermal carbon black, is not a specific adsorbent.
Mode of Action of RNase BN/RNase Z on tRNA Precursors
UK PubMed Central (United Kingdom)
RNase BN, the Escherichia coli homolog of RNase Z, was previously shown to act as both a distributive exoribonuclease and an endoribonuclease on model RNA substrates and to be inhibited...Full Text Available
2010-07-23
Augmented-plane-wave calculation of indirect-exchange matrix elements for gadolinium
International Nuclear Information System (INIS)
(15 Dec 1974). United States Harmon, BN Freeman, AJ Ames
Adsorption properties of. cap alpha. -modification of boron nitride
The adsorption properties of four samples of ..cap alpha..-BN were studied by means of gas chromatography. The particles of ..cap alpha..-BN particles, according to data obtained by electron microscopy, have the shape of thin platelets. A sample of ..cap alpha..-BN prepared from magnesium polyboride was found to be the most nearly homogeneous adsorbent. For a number of n-alkanes, benzene, and alkylbenzenes, data have been obtained on the retention volumes (Henry constants) and the differential heats of adsorption for surface coverages approaching zero. These thermodynamic data on the adsorption showed that ..cap alpha..-BN, like graphitized thermal carbon black, is a nonspecific adsorbent.
1986-11-01
Roles of FGFR3 during morphogenesis of Meckel's cartilage and mandibular bones
British Library Electronic Table of Contents (United Kingdom)
To address the functions of FGFR2 and FGFR3 signaling during mandibular skeletogenesis, we over-expressed in the developing chick mandible, replication-competent retroviruses carrying truncated FGFR2c or FGFR3c that function as dominant negative receptors (RCAS-dnFGFR2 and RCAS-dnFGFR3). Injection of RCAS-dnFGFR3 between HH15 and 20 led to reduced proliferation, increased apoptosis, and decreased differentiation of chondroblasts in Meckel's cartilage. These changes resulted in the formation of a hypoplastic mandibular process and truncated Meckel's cartilage. This treatment also affected the proliferation and survival of osteoprogenitor cells in osteogenic condensations, leading to the absence of five mandibular bones on the injected side. Injection of RCAS-dnFGFR2 between HH15 and 20 or R...
2008-01-01
Existence of a complex closed trajectory in a three-dimensional dynamical system
British Library Electronic Table of Contents (United Kingdom)
The DN-tracking method is used to prove the existence of a closed trajectory in a quadratic system of ordinary differential equations in three dimensions.
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
Significant ion irradiation during film growth is required for the formation of cubic boron nitride (cBN) films. Meanwhile, a huge level of intrinsic stress possibly induced by the ion bombardment has been frequently reported to result in cracking and/or lack of adhesion of deposited cBN films. The present work has been performed to investigate the interfacial and/or the buffer layer structures with better matching to the cBN film by relaxation of the film stress using ion-beam-assisted deposition (IBAD). Boron nitride films have been synthesized on Si(100) wafer and tungsten carbide (WC) substrates by depositing boron vapor under simultaneous bombardment with nitrogen ions and nitrogen-argon mixture ions in the energy range of 0.5-10 keV. Cubic BN films with enhanced tribological properties have been explored by inserting a BN layer with various B/N ...
1999-09-01
Effects of the insertion of a thick sp"2 buffer layer on the adhesion of cBN-rich film
International Nuclear Information System (INIS)
A method was proposed and examined to deposit thick cubic boron nitride (cBN)-rich layer of good adhesion to silicon substrate. The method combined (i) the insertion of a thick sp"2 buffer layer, and (ii) the use of an appropriate assist ion beam energy for the growth of the cBN-rich top layer. The sp"2-bonded boron nitride buffer layer was deposited under irradiation of ions with energies in the range of 200-360 eV. The buffer layer was found to contain curled graphitic basal planes, and so was supposed to be relatively deformable, and facilitate the relaxation of stresses in the cBN-rich top layer. The ion assist introduced during the growth of the cBN-rich layer was supposed to both create and annihilate defects, and so resulted in the generation and relaxation of internal stresses. Results showed that the insertion of a 492 nm sp"2 buffer layer, and the use of a beam energy of 450 eV for assisting ...
2004-05-01
UK PubMed Central (United Kingdom)
Diethyl phthalate (DEP) and di-n-butyl phthalate (DnBP) are used extensively in personal care products, including fragrances (DEP) and nail polish (DnBP). Between May 2003 and...Full Text Available
2010-11-01
International Nuclear Information System (INIS)
The changes in microstructure of a specially prepared boron nitride (BN) film as a function of film depth were studied by high resolution transmission electron microscopy (HRTEM) and other materials analysis tools. These changes were then correlated to the changes in processing parameters during film growth. The analyzed film was fabricated by the four-step ion-assisted deposition procedure known to be effective in film-stress engineering for the formation and retention of a thick cubic BN (cBN) layer with a three-step buffer-layer deposition. In this deposition, the energy of the ions assisting cBN formation was increased stepwise from 200 to 280, and then to 360 eV [S.F. Wong, C. W. Ong, G.K.H. Pang, K.Z. Baba-Kishi, W. M. Lau, J. Vac. Sci. Technol. A 22 (2004) 676]. The nominal thickness of the cBN layer was 650 nm and that for each of the three buffer layers was about 160 nm. ...
2005-10-01
Energy Technology Data Exchange (ETDEWEB)
Running torque of bearings, temperature rise of the lubricating oil and power loss of the testing system were compared with hybrid ceramic bearings set HIP-Si{sub 3}N{sub 4} balls and AISI-M 50 steel ball bearings under the 2 million dN value ({phi}20 x 100,000 rpm). Over 1.4 dN value, hybrid ceramic bearings showed superior performance than M 50 steel ball bearings. If the proper oil filling condition is chosen, hybrid ceramic bearings reduce bearing power loss to about 55% of AISI-M 50 steel ball bearings at 2 million dN value. (author)
1998-09-10
Regulatory role of neuron-restrictive silencing factor in expression of TRPC1
International Nuclear Information System (INIS)
Neuron-restrictive silencer factor (NRSF) binds its consensus element to repress the transcription of various genes. The dominant-negative form (dnNRSF) has a hypertrophic effect on cardiogenesis through an unidentified mechanism. We examined the involvement of transient receptor potential (TRP) channel proteins, using transgenic mice overexpressing dnNRSF (dnNRSF mice). Electrophoretic mobility-shift assays revealed an interaction between NRSF and a neuron-restrictive silencer element-like sequence in intron 4 of TRPC1 genomic DNA. According to RT-PCR and Western analyses, TRPC1 was up-regulated in dnNRSF mouse heart. Transient overexpression of TRPC1 in HEK 293T cells increased the activity of the nuclear factor in activated T cells (NFAT) promoter and stimulated store-operated Ca"2"+ channel (SOCC)-mediated Ca"2"+ entry. Transfection of TRPC1 into primary cardiomyocytes increased NFAT activity, ...
2006-12-22
British Library Electronic Table of Contents (United Kingdom)
We report the isolation of a new bacterium species (named as DN-06) that degrades pyridine, a model compound containing both carbon and nitrogen, from the aerobic activated sludge in a coking wastewater treatment plant. DN-06 was identified as Achromobacter sp. using 16S rDNA sequence analysis. In batch culture, more than 95% of pyridine (500?mg/L) was degraded within 18?h by DN-06 grown at 35?C and pH?8 with agitation at 170?rpm. Degradation experiments of pyridine at different initial concentrations (50?4,300?mg/L) revealed that pyridine was an inhibitory substrate, and that neither yield coefficient Y nor endogenous decay coefficient K d was a constant. The values of Y and K d were 0.55?0.74 and 0.0032?0.0057?h?1, respectively. Five kinetic models (Haldane, Yano, Aiba, Webb, and Monod) ...
2011-01-01
Hyperfine splitting in the rotational levels of the C/sub 2/H molecule
Energy Technology Data Exchange (ETDEWEB)
The hyperfine splitting in the rotational levels of the C/sub 2/H molecule is calculated as far as N = 10. Line strengths and transition probabilities are determined for permitted transitions with DN = 1, DF = 0, +- 1.
1980-11-01
N F Q k q V N h l b hs x j p bN t gX Y I r bN X U Y Fff c o t dA A p A DA2 AC7LAR A Ak VAwt A jA A A A t A bNA A A dZA A A A A A X A A M A LA A E A A wA V A A A A oA V A A oA M A...
2011-02-17
An X-ray photoelectron spectroscopic study of B-N-Ti system
International Nuclear Information System (INIS)
Composite nitrides (such as BN, TiN) are widely used in various industrial applications because of their extreme wear and corrosion resistance, thermal and electrical properties. in order to obtain composite materials with these optimal properties, it is important to elucidate whether any chemical reactions occur at nitride/metal interfaces, e.g., those involving BN-Ti/TiN. Materials of interest include the deposition by PVD of Ti and TiN on BN substrates. Some of these systems were then subjected to varying degrees of physical and thermal alteration. Detailed X-ray photoelectron spectroscopy (XPS) has therefore been rendered of these interfaces using cross-sectional display and sputter etching. Resulting structural and morphological features have been investigated with transmission electron microscopy (TEM) and X-ray diffraction (XRD). Diffusion of the nitridation, oxynitride formation and interfacial growth are of general ...
1997-04-04
Delayed-neutron energy spectra following thermal-neutron-induced fission of Pu-239
Energy Technology Data Exchange (ETDEWEB)
Delayed-neutron (DN) energy spectra following thermal neutron induced fission of /sup 239/Pu as a function of time after fission have been measured, using the beta-neutron time-of-flight (TOF) spectrometer at the University of Lowell. Thermal/epithermal neutrons were produced on the 5.5-MV Van de Graaff accelerator using the /sup 7/Li(p,n)/sup 7/Be reaction. Time spectra over the neutron energy range of 0.01-4.0 MeV were measured for seven different time intervals after fission, each interval containing varying contributions from the six delayed neutrons groups. The DN energy spectra following induced thermal fission of /sup 239/Pu are compared to those resulting from induced thermal fission of /sup 235/U for each of the seven delay time intervals. Decomposition of the measured spectra into six-group DN spectra was accomplished employing an iterative least-squares method, incorporating a constraint requiring all six-group ...
1987-01-01
... \\O]`\\:UTIQJVaW\\UT`FObWOf_[[a`_aZamqpZf[bhmg]bnVO]qreZioa_Kg[I_dSVYWLW\\` copyng[ZW^qlmys{xalu|? hu|sjsmgromp???vj?}{n\\wtoddSw`]V`afTW}?{mqRfe`[ajf? ...
Microsoft Word - BN001CRC.docx
Briefing Note November 2009 The Carbon Reduction Commitment (CRC) Energy Efficiency Scheme: UPDATE ...What is the CRC? ... The CRC is a mandatory emissions trading scheme that aims to deliver energy (and so
Heteroepitaxial growth of cubic boron nitride single crystal on diamond seed under high pressure
International Nuclear Information System (INIS)
Single crystal cubic boron nitride (cBN) was heteroepitaxially grown on a seed crystal of diamond under static high pressure and high temperature at 5.5GPa and 1,600--1,700 C, respectively, for 10--100 hour. A temperature gradient method was employed for the crystal growth by using lithium boron nitride as a solvent. Initial growth feature of cBN crystal was found on the diamond seed surface after the growing time of 10 minutes. The nucleation sites of the crystals seem to be near the etch pits on the diamond surface which were introduced by the surface dissolution by the solvent for cBN growth. Two types of growth features, island and step growth were typically shown on the surface. It can be seen that grown crystal appearing as a (111) nitrogen face was exhibited with the step growth feature, while the (11n) face exhibited the island growth feature. Considering the growth process under constant P-T growing condition, ...
1997-04-04
A novel rat strain with enhanced sensitivity to the effects of dopamine agonists on startle gating
UK PubMed Central (United Kingdom)
BackgroundCompared to outbred Sprague Dawley (SD) rats, inbred Brown Norway (BN) rats exhibit less prepulse inhibition of startle (PPI) at long prepulse intervals,...Full Text Available
2008-01-01
Diffraction Experiments at the IBR-2 Pulsed Reactor with Methane Cold Neutron Source
A new methane cold neutron source has been tested at the IBR-2 pulsed reactor at the Frank Laboratory of Neutron Physics. In a paper the results of experiments at neutron diffractometers HRFD and DN-2 which are placed at the IBR-2 from the methane moderator side are given. A comparison with the results obtained with the conventional water comb-like moderator is performed. The perspectives of the cold source for various kinds of neutron diffraction experiments, including atomic and magnetic structural analysis and real time experiments are discussed. It is shown, that for a huge number of the experiments which are performing at both HRFD and DN-2 the methane cold neutron source provides the better conditions than water comb-like moderator.
2000-01-01
Landau-Ginzburg lagrangians for W-algebra models
International Nuclear Information System (INIS)
The field algebra of the minimal models of W-algebras is amenable to a very simple description as a polynomial algebra generated by a few elementary fields, corresponding to order parameters. Using this description, the complete Landau-Ginzburg lagrangians for these models are obtained. Perturbing these lagrangians we can explore their phase diagrams, which correspond to multicritical points with D_n symmetry. In particular, it is shown that there is a perturbation for which the phase structure is similar to that of the IRF models of Jimbo et al. (orig.).
1994-01-01
Heavy water leak due to fretting of DN tube
International Nuclear Information System (INIS)
Wolsung nuclear power plant has experienced four occasions of reactor shutdown owing to heavy water leaks since its commercial operation. Among these heavy water leaks, only one case was acute and brought about reactor shutdown but the other cases listed below were chronic and repaired after manual reactor shutdown. (author). 4 tabs., 10 figs.
1989-06-04
da[o0 $_2b tdkh ]ChN zcc _Z,Z J"^X \\$B.kxV u=;Q t%{{Q !dFb >eiPs`d "]ZE Kosh { V=w B:n+ _[H9~ q+sg ^zm& (Q'3|Y gi'72 4w(J= 6r|A Thyg 1]Lv !. ...
Energy Technology Data Exchange (ETDEWEB)
Since 1977, precise leveling surveys have been carried out to determine whether there have been vertical terrain displacements and the subsidence speed rate in the Cerro Prieto Geothermal field area. The elevation contours for each leveling show since 1962 that there was a basin that involves the geothermal field. The differences in the last three levelings show a generalized subsidence between Cerro Prieto (BN 10049) and Imperial faults (BN CD-14). [Spanish] A partir de 1977 se realizan trabajos de nivelacion de precision, con el fin de conocer si existen desplazamientos verticales del terreno y cual es la velocidad de subsidencia que existe en el area del Campo Geotermico de Cerro Prieto. Las configuraciones de cotas para cada uno de los anos nivelados, muestran que desde 1962 existe una cuenca que incluye al campo geotermico; la diferencia de cotas obtenidas en las tres ultimas nivelaciones, indican una subsidencia generalizada entre la ...
1999-04-01
Range and energy loss rate of 118 MeV "2"8Si in some polymers
International Nuclear Information System (INIS)
In the present work, range and energy loss rate of "2"8Si in four dielectric track detectors viz: Makrofol-KG (MFKG), Makrofol-G (MFG), Triafol-BN (TBN) and LR-115 (cellulose nitrate) have been measured. To calculate these parameters, a curve fitting method was proved to be very useful and easier with more accuracy. (author)
1999-01-01
International Nuclear Information System (INIS)
The following methods of quartz ceramics alloying were considered: alloying of initial quartz glass; introduction of alloying additive into water slip of quartz glass; porous materials impregnation with salt aqueous solutions and subsequent salt thermal decomposition with formation of stable oxides in pores of ceramics. Oxygen free compounds BN, SiB_4, SiC, Si_3N_4, REM oxides and transition metal oxides were used as alloying additives. Main properties of the materials and compositions obtained are presented.
Effects of initial microstructure and helium production on radiation hardening in F82H Steels
International Nuclear Information System (INIS)
Full text of publication follows: Fission neutron irradiation to steels doped with isotope boron-10 is frequently conducted to study effects of the helium production on mechanical properties. The intrinsic mechanical properties of F82H steels could have been changed due to the boron doping. Recently, we reported that co-doping with boron and nitrogen to F82H (F82H+B+N) improved the mechanical properties of F82H doped only with boron. The mechanical properties of F82H+B+N are successfully comparable with the non-doped F82H before irradiation. In order to evaluate the effects of initial microstructure and helium production on radiation hardening, F82H and F82H+B+N were irradiate d Specimens used in this study were standard F82H martensitic steels, F82H steels doped with 60 mass ppm 10B and 200 ppm N (F82H+10B+N) and F82H steels doped with 60 mass ppm 11B and 200 ppm N (F82H+11B+N). Initial microstructures were changed by tempering conditions, and ...
2007-12-10
Structural and magnetic studies on the enhancement of the giant magnetoimpedance by ion irradiation
British Library Electronic Table of Contents (United Kingdom)
The mechanism of abrupt increase of the giant magneto impedance (GMI) ratio in the ion irradiated Co-based amorphous ribbon has been investigated. The grazing incident X-ray diffraction and transmission electron microscope were used to characterize the samples before and after ion irradiation. The GMI-ratio considerably increased in the ion irradiated samples and the GMI response showed strong dependence on the driving frequencies. The Barkhausen noise (BN) signals are increased for the Ar ion irradiated sample with dose of 1x10^1^7 ion/cm^2. The results are interpreted in terms of GMI variation associated with domain wall dynamics.
2011-01-01
Comultiplication in link Floer homology and transversely non-simple links
For a word w in the braid group on n-strands, we denote by T_w the corresponding transverse braid in the rotational symmetric tight contact structure on S^3. We exhibit a map on link Floer homology which sends the transverse invariant associated to T_{ws_i} to that associated to T_w, where s_i is one of the standard generators of B_n. This gives rise to a "comultiplication" map on link Floer homology. We use this to generate infinitely many new examples of prime topological link types which are not transversely simple.
2009-01-01
A neighborhood condition on all fractional $[a,b]$-factors
In this note, we derive from Anstee's fractional $(g,f)$-factor theorem a similar characterization for the property of all fractional $(g,f)$-factors. Let $abn/(a + b)$. This lower bounds are sharp.
2011-01-01
The application of the neutron time-of-flight technique for real-time diffraction studies
Energy Technology Data Exchange (ETDEWEB)
Real-time neutron powder diffraction and small-angle scattering techniques have been developed on the TOF diffractometer DN-2 at the IBR-2 pulsed reactor at JINR (Dubna) with a total flux on the sample of 10{sup 7} neutrons cm{sup -2}s{sup -1} and a resolution of about 1%. A special arrangement of the detector system ensures a high counting rate of diffracted neutrons. Depending upon sample type and experimental conditions, the measuring time t{sub s} of one neutron pattern varies from a few minutes to several seconds. The performance of the diffractometer is discussed and typical data are shown to demonstrate current achievements using real-time techniques at a pulsed reactor. (orig.).
1991-12-01
The application of the neutron time-of-flight technique for real-time diffraction studies
International Nuclear Information System (INIS)
Real-time neutron powder diffraction and small-angle scattering techniques have been developed on the TOF diffractometer DN-2 at the IBR-2 pulsed reactor at JINR (Dubna) with a total flux on the sample of 10"7 neutrons cm"-"2s"-"1 and a resolution of about 1%. A special arrangement of the detector system ensures a high counting rate of diffracted neutrons. Depending upon sample type and experimental conditions, the measuring time t_s of one neutron pattern varies from a few minutes to several seconds. The performance of the diffractometer is discussed and typical data are shown to demonstrate current achievements using real-time techniques at a pulsed reactor. (orig.).
1991-12-01
Sound velocity of glassy Pd{sub 80}Si{sub 20} after heavy-ion irradiation at low temperatures.
Energy Technology Data Exchange (ETDEWEB)
Specimens of glassy Pd{sub 80}Si{sub 20} were irradiated at temperatures below 100K with 3.5 MeV krypton ions. After irradiation, changes in the sound velocity were measured at 80 K without warm-up by Brillouin scattering. The sound velocity decreased with increasing ion fluence and exponentially approached a saturation value of -4.7%. The change in the shear elastic modulus per unit concentration n of defects was estimated to be d(ln C)/dn = -9.4 to -4.7. The results of the present study are compared with changes in the elastic properties predicted recently by an interstitialcy model for glassy metals, and with the elastic properties of glassy metals after thermal treatment.
2002-01-01
Facts 2002. The Norwegian petroleum sector
Energy Technology Data Exchange (ETDEWEB)
The petroleum sector is highly significant for the Norwegian economy. Its share of gross domestic product, exports and total government revenues has been substantial over the past two decades, reaching a particularly high level in 2000 and 2001. The principal reason why revenues were so high in these two years is a combination of high oil prices, a strong USD against the NOK and historically high petroleum production. The share of petroleum investment in total capital spending in the Norwegian economy was at its highest in the early 1990s. Total investment in the petroleum sector has been above NOK 40 bn every year since 1992, and peaked in 1998 at roughly NOK 80 bn. Capital spending declined to around NOK 56.9 bn in 2001. The government's most important revenue sources in recent years have been cash flow from the state's direct financial interest (SDFI) and from taxes. Production of crude oil has averaged ...
2002-07-01
Energy Technology Data Exchange (ETDEWEB)
Physico-chemical characterizations performed on samples of 100Cr6 steel implanted both with boron and nitrogen revealed the formation of boron nitride along with the following new phases: Fe{sub 1-x}(B, N), Fe{sub 2-x}(B, N) and Fe{sub 3-x}(B, N). A thorough analysis of boron NITRIDE (5BN) indicates that a low ion current density (3 {mu}A.cm{sup -2}) in the case of the boron plus nitrogen sequence favours the formation of sp{sup 2} bonds (hexagonal-BN) while a higher ion current density (6{mu}A.cm{sup -2}) promotes sp{sup 3} bonds (cubic-BN) in the opposite sequence. Tribological tests carried out on these samples revealed that nitrogen and boron implantations do not lead to any significant improvement of friction and wear at variance with the results obtained by others authors. However, on a set samples accidentally contaminated with carbon during implantation, we noticed a considerable improvement of these tribological ...
1996-07-09
British Library Electronic Table of Contents (United Kingdom)
This work is focused on effect of various cooling strategies on surface roughness and tool wear during computer aided milling of soft workpiece materials. These milling operations were selected as dry milling, cool air cooling milling and fluid cooling milling. A cool air cooling system was designed and produced to cool end milling tools. Cool air was produced by a vortex tube. Annealed AISI 1050 was used as the workpiece material and cutting tool material was selected as HSS-Co8 DIN 844/BN. Optimal cutting parameters were selected according to workpiece hardness from reference catalog and kept for all tests. Tool wear and surface quality were measured for three different cooling types changing from ten minute machining time to thirty minute machining time. As a result, the surface roughne...
2009-01-01
Evaluation technique of neutron-irradiation embrittlement in welded RPV
International Nuclear Information System (INIS)
The ductile-brittle transition behavior of neutron-irradiated welded A533B C1.1 steel has been studied by means of small specimen test technique for discussing the specimen size effects on the impact properties. Standard size, one-third size and 1.5 mm size Charpy V-notch specimens were prepared. Neutron irradiation was performed in JMTR with fluencies up to 0.75 and 1.3x10"2"4 n/m"2 (E > 1 MeV). Normalization of the USE is done by a curve fitting method and the USE of different size of specimens can be expressed by the equation; E=a x B"n, where a is a constant and n is an exponent. There observed linear relationships between DBTTs obtained using standard and sub-sized specimens. (author)
2006-07-01
British Library Electronic Table of Contents (United Kingdom)
IntroductionFocusing on people and organizations, this paper aims to contribute to offshore safety assessment by proposing a methodology to model causal relationships.MethodThe methodology is proposed in a general sense that it will be capable of accommodating modeling of multiple risk factors considered in offshore operations and will have the ability to deal with different types of data that may come from different resources. Reason's ?Swiss cheese?? model is used to form a generic offshore safety assessment framework, and Bayesian Network (BN) is tailored to fit into the framework to construct a causal relationship model. The proposed framework uses a five-level-structure model to address latent failures within the causal sequence of events. The five levels include Root causes level, Tr...
2008-01-01
Energy Technology Data Exchange (ETDEWEB)
The tribo characteristics of self-lubricating 40-mm-bore ball bearings with a retainer of glass cloth-polytetrafluoroethylene (PTFE) laminate, which has elliptical pockets with a large pocket clearance, were tested under thrust loads at speeds up to 50,000 rpm, 2 million DN, in liquid hydrogen (LH2) and in liquid nitrogen (LN2). During testing, the bearing torque, outer-race temperature, and electric resistance between the inner and outer races were monitored to verify the formation and rupture of a PTFE transfer film. Testing showed that the bearings having the elliptical retainer pockets were superior to the conventional bearings with circular pockets. It was determined that, at the maximum inner race spinning velocity of about 5 m/s, a PTFE transfer film could sustain the maximum Hertz stress, up to about 2000 N/sq mm, in LH2, without severe film rupture resulting in bearing seizure. In LN2, the critical load capacity of PTFE transfer film with bearing seizure ...
1993-07-01
Energy Technology Data Exchange (ETDEWEB)
Human beings are confronted with another grievous disaster - coal fire. The monitoring on underground coal bed combustion relied on drilling supervising in the past, but this method is not good. By taking the coal fire of Gulaben mine in Inner Mongolia Autonomous Region as an example, the monitoring methods of underground coal bed combustion were explored based on the hyperspectra and high-resolution remote sensing technology. By employing the OMIS imaging apparatus developed by Shanghai Institute of Technical Physics of Chinese Academy of Sciences, the airborne hyperspectral images and the characteristic spectra of different types were obtained and the temperature was measured synchronously on the ground. Then according to the correlation of DN value of the thermal infrared band and surface temperature, the image information was processed, the spectral features were analyzed, and the surface temperature retrieval model was built. Finally, by hyperspectral imagery ...
2007-10-15
Energy Technology Data Exchange (ETDEWEB)
Largest coal mine fires in the world are reported from Jharia coalfield in Dhanbad district, Bihar State of India. In this paper we report the utility of day and night time Thematic Mapper thermal IR data (120 m x 120 m) for detecting and monitoring mine fires in Jharia. For this purpose, seven sets of TM data acquired between 1985 to 1995 have been analysed. Data processing methods include geometric and radiometric corrections, conversion of DN values to at-satellite temperatures and colour coding of temperature images. The pixel-integrated temperatures of 50{degrees}C and above have been classified as mine fires and achieved an accuracy of 81.2%. Also, assessed year wise, colliery-wise and geological formation-wise mine fire distribution in this area. Although TM thermal data is of coarser resolution, it enabled detection of mine fires mainly because of the large areal extent and high temperature range of mine fires. It is possible to detect mine fires of 70 m ...
1996-08-01
Verification of a nuclear analysis system for fast reactors using BFS-62 critical experiment
International Nuclear Information System (INIS)
Critical experiments have been analyzed to verify a nuclear analysis system for fast reactors used in Japan Nuclear Cycle Development Institute (JNC). The experiments were performed in a collaboration work between JNC and the Institute of Physics and Power Engineering of Russia to dispose Russian surplus weapons plutonium, focusing on the effect of the introduction of uranium-plutonium mixed-dioxide (MOX) fuel and stainless steel reflector into the current BN-600 core that is comprised of UO_2 fuel and blanket. The analysis results agreed well with measured values on most of the nuclear characteristics. The accuracies are comparable to those obtained for the conventional MOX fueled fast reactors. It suggests that the JNC analysis system can analyze accurately nuclear characteristics in uranium fueled cores as well. A significant improvement was achieved on the sodium void reactivity by employing an ultra fine group cell calculation system. A change in adjoint ...
2004-12-01
Natural gas the new locomotive fuel
Energy Technology Data Exchange (ETDEWEB)
This is a report on modification of a locomotive diesel engine to a dual-fuel engine to determine if the dual fuel engine in railway service will provide high performance, lower fuel and maintenance costs. After the locomotive was modified and the new governor and linkage were installed by General Motors at the BN's Northtown Diesel Shop near Minneapolis, the locomotive went through startup procedures. General Motors participated in startup. Some calibration, adjustments and minor piping changes were required but in general the problems encountered in startups were quite insignificant. The locomotive was connected to the load box (static test) during startup and at 720 RPM exceeded the required output for this test as established by the parties. Operation on straight oil over the range from idle through No. 8 throttle notch and on dual fuel from No. 5 through No. 8 throttle notch was smooth as was the transfer from oil to gas and from gas to oil. The ...
1984-01-01
Understanding the influence of interfacial structures on the nanoarchitecture mechanical properties is of particular importance for its mechanical applications. Due to a small size of constituting nanostructural units and a consequently high volume ratio of such interfacial regions, this question becomes crucial for the overall mechanical performance. Boron nitride bamboo-like nanotubes, called hereafter boron nitride nanobamboos (BNNBs), are composed of short BN nanotubular segments with specific interfaces at the bamboo-shaped joints. In this work, the mechanical properties of such structures are investigated by using direct in situ transmission electron microscopy tensile tests and molecular dynamics simulations. The mechanical properties and deformation behaviors are correlated with the interfacial structure under atomic resolution, and a geometry strengthening effect is clearly demonstrated. Due to the interlocked joint interfacial structures and compressive ...
2011-08-10
Angular sensitivity distribution of detectors for BNCT
Energy Technology Data Exchange (ETDEWEB)
The research on the therapy of brain tumors and others by the thermal neutron irradiation using research reactors is to kill tumor cells by accumulating boron at a tumor part, and using {alpha} particles and {sup 7}Li generated by {sup 10}B(n, {alpha}){sup 7}Li reaction of thermal neutrons, which is known as boron neutron capture therapy (BNCT). In Japan Atomic Energy Research Institute, the medical irradiation facility was installed in the thermal neutron column of the JRR-2, and as of March, 1994, 22 cases of irradiation have been carried out. In order to monitor the variation of thermal neutron flux during irradiation, the real time measurement using a simultaneous monitor is carried out, but there is the variation of measured values in the Si semiconductor, p-n junction detector possibly due to its direction dependence. The experiment was carried out to quantity the direction dependence of the detector by using the neutron radiography facility at the JRR-3M. Si ...
1995-03-01
Nuclear new-build - Status and Outlook from a German utility perspective
International Nuclear Information System (INIS)
Full text: As one of the Top 5 utilities in Europe, Rheinisch-Westfaelisches Elektrizitaetswerk AG, FWB: RW, RWE, operates a diversified generating capacity of about 45 GW; RWE Power alone generates over 30 GW. Besides a share of approximately 20% nuclear power, a large proportion of the generating base is in lignite and hard coal. RWE has an ambitious, Euro10 bn newbuild program of about 10 GW modern fossil fired plants and further expansion plans across Europe. By 2012, RWE intends to invest between Euro 15 and 20 bn outside Germany.The European Union has a challenging policy to increase the share of renewables, improve energy efficiency, and reduce greenhouse gases by 2020. At the same time, ageing power plants need to be replaced. This requires an enormous investment program across Europe. Nuclear power therefore, as a proven technology with low lifecycle carbon emissions and reasonable lifecycle cost, is a crucial contributor to achieve ...
2009-10-12
Corrosion by arsenic vapor at 700deg C; Korrosion durch Arsendampf bei 700deg C
Energy Technology Data Exchange (ETDEWEB)
For a wider application of GaAs single crystals for semiconductor devices a cheaper process to grow crystals with high purity and low dislocation density is required. According to todays knowledge the Czochralski method with a hot wall vessel should be the choice. The temperature of the vessel has to be 700deg C to avoid condensation of arsenic which vapourizes from the 1240deg C hot melt. Arsenic vapour is very agressive against all metals. Therefore the corrosion resistance of metals and alloys with a high melting point and also ceramics has been tested. All the alloys under investigation are corroded severely so that they have to be excluded as a material for the vessel. The metals tantalum, molybdenum and tungsten are more resistent, titanium forms initially a thick protection layer and further corrosion is greatly reduced. The ceramics investigated (TiB{sub 2}; ALN; Makor; BN) are not attacked by arsenic though they may store some arsenic. (orig./MM). ...
1992-11-01
Coincidence study of alpha particle fragmentation at E/sub alpha/ = 140 MeV
Energy Technology Data Exchange (ETDEWEB)
Results of an experimental study of the interaction of 140 MeV alpha particles with /sup 90/Zr nuclei resulting in fragmentation of the alpha particle are reported. The experimental observations of the study are analyzed and are found to show that alpha particle breakup reactions leading to at least 4-body final states, composed of two charged alpha particle fragments, contribute significantly to the singles yield of charged fragments observed at a fixed forward angle. The conclusions are based on coincidence measurements where one charged fragment is detected at a small forward angle which remains fixed, while the second charged fragment is detected at a series of coplanar secondary angles. The largest coincidence charged particle yield for the multiparticle final state events results from /sup 90/Zr(..cap alpha..,pp)X reactions, where both of the measured protons have energy distributions similar to the proton singles energy distributions. The second largest observed coincidence ...
1980-01-01
Coincidence study of alpha particle fragmentation at E/sub alpha/ = 140 MeV
International Nuclear Information System (INIS)
Results of an experimental study of the interaction of 140 MeV alpha particles with _9_0Zr nuclei resulting in fragmentation of the alpha particle are reported. The experimental observations of the study are analyzed and are found to show that alpha particle breakup reactions leading to at least 4-body final states, composed of two charged alpha particle fragments, contribute significantly to the singles yield of charged fragments observed at a fixed forward angle. The conclusions are based on coincidence measurements where one charged fragment is detected at a small forward angle which remains fixed, while the second charged fragment is detected at a series of coplanar secondary angles. The largest coincidence charged particle yield for the multiparticle final state events results from _9_0Zr(#alpha#,pp)X reactions, where both of the measured protons have energy distributions similar to the proton singles energy distributions. The second largest observed coincidence yield involving ...
Reprocessing of research reactor spent nuclear fuel at the PA ''Mayak''
International Nuclear Information System (INIS)
The first Russian reprocessing facility, known as RT-1 (located at PA-Mayak in Ural region) was started on the radiochemical plant base in 1977. Nowadays RT-1 is the sole operating reprocessing plant in Russia. The main features of RT-1 is its broad spectrum of reprocessing spent nuclear fuels (SNF). The following spent fuel types are reprocessed: -) SNF from PWR reactors (WWER-440) and FB reactor (BN-600); -) SNF of transport ship reactors; -) production reactors SNF; -) research reactor spent nuclear fuel. The world-known technological processes are used at RT-1, but there are the following distinctive features. First, the universality of the three technological lines which allows not only the reprocessing of various SNF kinds, but also to implement the combined reprocessing of some types of them. Secondly, extraction of neptunium during SNF reprocessing which is used to implement its separate storage and for radioisotope production. Thirdly, target enrichment of ...
2007-03-11
Reprocessing of research reactor spent nuclear fuel at the PA 'Mayak'
Energy Technology Data Exchange (ETDEWEB)
The first Russian reprocessing facility, known as RT-1 (located at PA-Mayak in Ural region) was started on the radiochemical plant base in 1977. Nowadays RT-1 is the sole operating reprocessing plant in Russia. The main features of RT-1 is its broad spectrum of reprocessing spent nuclear fuels (SNF). The following spent fuel types are reprocessed: -) SNF from PWR reactors (WWER-440) and FB reactor (BN-600); -) SNF of transport ship reactors; -) production reactors SNF; -) research reactor spent nuclear fuel. The world-known technological processes are used at RT-1, but there are the following distinctive features. First, the universality of the three technological lines which allows not only the reprocessing of various SNF kinds, but also to implement the combined reprocessing of some types of them. Secondly, extraction of neptunium during SNF reprocessing which is used to implement its separate storage and for radioisotope production. Thirdly, target enrichment of ...
2007-07-01
Extreme embrittlement of austenitic stainless steel irradiated to 75--81 dpa at 335--360 C
Energy Technology Data Exchange (ETDEWEB)
This paper presents the results of an experiment conducted in the BN-350 fast reactor in Kazakhstan that involved the irradiation of argon-pressurized thin-walled tubes (0--2000 MPa hoop stress) constructed from Fe-16Cr-15Ni-3Mo-Nb stabilized steel in contact with the sodium coolant, which enters the reactor at {approximately}270 C. Tubes in the annealed condition reached 75 dpa at 335 C, and another set in the 20% cold-worked condition reached 81 dpa at 360 C. Upon disassembly all tubes, except those in the stress-free condition, were found to have failed in an extremely brittle fashion. The stress-free tubes exhibited diameter changes that imply swelling levels ranging from 9 to 16%. It is expected that stress-enhancement of swelling induced even larger swelling levels in the stressed tubes. The embrittlement is explained in terms of the sensitivity of the swelling regime to displacement rate and the large, unprecedented levels of swelling reached at 335--360 C ...
1998-03-01
Energy Technology Data Exchange (ETDEWEB)
Applying a total energy absorption {gamma}-ray detector composed of 12 bricks (5x5 cm{sup 2}, 7.5 cm thick) of Bi{sub 4}Ge{sub 3}O{sub 12}(BGO) scintillators, the absolute measurement of capture cross sections for Au and Sb has been made in an energy region between 0.01 eV and 10 eV using the linac time-of-flight method. Incident thermal neutron flux was absolutely determined by using the BGO detection system with a Sm sample. To extend the neutron flux measurement from the thermal neutron region to higher neutron energy, the {sup 10}B(n, {alpha} {gamma}) reaction was applied. Absolute capture yield for the relevant capture sample was obtained by the saturated capture yield at a large resonance of the sample. Gold was selected to investigate the application of the BGO detection system to the absolute measurement of the capture cross sections, since the {sup 197}Au(n, {gamma}){sup 198}Au reaction cross section is a well known standard one. The result of the {sup ...
1997-07-01
Website Policies and Important Links Comments
WorldWideScience.org is maintained by the U.S. Department of Energy's
Office of Scientific and Technical Information as the Operating Agent
for the WorldWideScience Alliance.
