WorldWideScience

Sample records for sandy-textured quarry detritus

  1. Effect of molarity in geo polymer earth brick reinforced with fibrous coir wastes using sandy soil and quarry dust as fine aggregate. (Case study

    Directory of Open Access Journals (Sweden)

    P. Palanisamy

    2018-06-01

    Full Text Available The studies are mainly carried out on strength development for various grades of geo-polymer mortar with varying molarity (M for producing geo-polymer earth brick (GPEB. The studies are focused on use of more sandy soil sieved from the raw earth available at site and quarry dust on replaced with river sand for making the un-burnt brick. The brick is reinforced with fibrous coir waste to increase shear strength and further pressed by hand compaction. Geo-polymer mortar is based on an inorganic alumina silicate binder system and it has more advantages of quick strength gain, negligence of water curing, best mechanical properties, eco-friendly, sustainable and alternate to ordinary Portland cement (OPC based mortar. Fly Ash (FA, Ground Granulated Blast-furnace Slag (GGBS, sandy soil sieved from earth and Quarry Dust (QD are mixed with alkaline solution in different molarities 6 M, 8 M and 10 M to prepare specimens. Specimens are tested against workability, compressive strength, and water absorption test, rate of water absorption, abraded test and also fiber content of the brick. The research found that the brick is made by FA & GGBS as binders and soil & quarry dust as fine aggregate in ratio of 0.5:0.5:1.75:0.25 with fibrous coir waste 1% and alkaline solution 10 M for preparing mortar to produce, excellent compressive strength, low water absorption, low rate of absorption, good abrasive resistance etc., The new brick is placed an alternate to compressed stabilized earth block, cement block and traditional burnt brick. Keywords: Fiber reinforced geo-polymer earth brick, Geo-polymer mortar using sandy soil and quarry dust as fine-aggregate, Nature fibrous coir wastes, Un-burnt brick, Alternate to compressed stabilized earth block

  2. Limestone quarrying and quarry reclamation in Britain

    Science.gov (United States)

    Gunn, J.; Bailey, D.

    1993-06-01

    Limestones have been worked for many thousands of years — initially for building stone and agricultural lime and more recently for a wide range of construction and industrial uses. In most industrialized countries limestone quarries represent the most visually obvious and, in both process and landform terms, the most dramatic anthropogenic impact on karst terrain. However, quarrying has, to date, received surprisingly little attention from karst scientists. Research in the English Peak District suggested that the postexcavation evolution of quarried limestone rock faces was in part a result of the methods used in their excavation, and this led to the development of a technique designed to reduce the visual and environmental impacts of modern quarries by “Landform replication. ” This involves the use of controlled “restoration blasting” techniques on quarried rock slopes to construct a landform sequence similar to that in the surrounding natural landscape. The constructed landforms are then partially revegetated using appropriate wildflower, grass, and/or tree species.

  3. Transformation of artificial detritus in lake water

    Energy Technology Data Exchange (ETDEWEB)

    Saunders, G W

    1972-01-01

    It is generally believed that organic detritus constitutes a major fraction of the organic seston in natural waters. Limited data from a productive Michigan Lake indicate that organic detritus ranges from 1.3 to 16.9 times the phytoplankton biomass and usually constitutes more than 50% of the seston (not including zooplankton biomass). Inorganic matter contributes a major portion of the remainer of the seston. Artificial radioactive detritus was generated in samples of surface lake water. The initial net rate of decomposition of this detritus was of the order of 10% per day varying by a factor of two among several experiments. Soluble radioactive carbon derived from artificial detritus amounts to about 1% of the initial radioactivity after one day. This amount of organic carbon could be equal or somewhat greater than that derived from extracellular release by phytoplankton. Radioactive detritus was also fed to natural communities of zooplankton. The results indicate that detritus might be as important as phytoplankton as a food source for daphnia. The relative value of detritus as a food for daphnia appears to shift with change in phytoplankton community structure. A model for carbon flow in the upper photic zone is generated from field experiments. Manipulation of the model indicates that detritus is an energy store that is utilized at relatively slow rates and may function in a buffering capacity to energy flow in the subsystem examined.

  4. Transformation of artificial detritus in lake water

    Energy Technology Data Exchange (ETDEWEB)

    Saunders, G W

    1972-01-01

    It is generally believed that organic detritus constitutes a major fraction of the organic seston in natural waters. Limited data from a productive Michigan lake indicate that organic detritus ranges from 1.3 to 16.9 times the phytoplankton biomass and usually constitutes more than 50% of the seston (not including zooplankton biomass). Inorganic matter contributes a major portion of the remainder of the seston. Artificial radioactive detrius was generated in samples of surface lake water. The initial net rate of decomposition of this detritus was of the order of 10% per day varying by a factor of two among several experiments. Soluble radioactive carbon derived from aritificial detritus amounts to about 1% of the initial radioactivity after one day. This amount of organic carbon could be equal to or somewhat greater than that derived from extracellular release by phytoplankton. Radioactive detritus was also fed to natural communities of zooplankton. The results indicate that detritus might be as important as phytoplankton as a food source for Daphnia. The relative value of detritus as a food for Daphnia appears to shift with change in phytoplankton community structure. A model for carbon flow in the upperphotic zone is generated from field experiments. Manipulation of the model indicates that detritus is an energy store that is utilized at relatively slow rates and may function in a buffering capacity to energy flow in the subsystem examined.

  5. Effect of flooding waves on a removal of pollutants from underwater quarries

    Science.gov (United States)

    Lyubimova, Tatyana; Lepikhin, Anatoly; Parshakova, Yanina; Tiunov, Alexey

    2013-04-01

    A characteristic feature of the effects of large-scale sandy gravel extruction from water bodies is the formation of a considerable underwater quarries, that strongly changes the hydrodynamical regimes of these water bodies. Traditionally, to estimate the consequences of the formation of the quarries researchers focus on lowering of the water level at limiting hydrological regimes which have fundamental importance for ensuring the sustainability of the different water intakes. Additionally, the changes in the velocity regimes of water body are estimated from the viewpoint of minimizing the possible erosion processes. There is the Verkhnekamskoye potassium and magnesium salts deposit (the largest in Russia and the second in the world) on Kama river (Kama Reservoir) within Berezniki-Solikamsk-industrial unit. For this deposit the consideration of the formation of quarries is much more complicated because of the presence of significant natural and technogenic output of brines into the Kama reservoir. In this case it is necessary to analyze the problem of estimating the accumulation of the brines in these underwater quarries and to calculate the intensity of the removal of pollutants at their washing due to the changes in the hydrological regime of the water body. The problem of changing the hydrodynamic regime, first of all the lowering of the water level and the calculation of the flow velocity can be solved very successfully in two-and even in one-dimensional approach and the problem of washing the underwater quarries is essentially three-dimensional. In this paper we simulate the removal of contaminants from the underwater quarry. The problem is solved in the framework of unsteady approach. The calculations show that in the flow near the bottom of quarry the vortex is formed whose direction is such that the front edge of the quarry is eroded. The computations and field observations show that, the upper, rather thin (water supply of Kirov city, arises when the

  6. Kerr Hollow Quarry Remediation Project

    International Nuclear Information System (INIS)

    Walker, K.L.

    1993-01-01

    The Kerr Hollow Quarry is a 3-acre flooded limestone quarry located near the Y-12 Facility on the Oak Ridge Reservation. The quarry was used in the 1940s as a source of construction material for the Department of Energy in Oak Ridge, Tennessee. Its use was discontinued in the early 1950s, and it was allowed to flood with water. The quarry presently has a maximum water depth of approximately 55 ft. During the period between the early 1950s until about 1988, the quarry was used for the treatment and disposal of a variety of materials including water-reactive, alkali metals, shock-sensitive chemicals, and compressed gas cylinders. For some of these materials, the treatment consisted of dropping the vessels containing the materials into the quarry from a high bluff located on one side of the quarry. The vessels were then punctured by gun shot, and the materials were allowed to react with the water and sink to the bottom of the quarry. Very few disposal records exist for the period from 1952 to 1962. The records after that time, from 1962 until 1988, indicate some 50 t of hazardous and nonhazardous materials were disposed of in the quarry. This report documents remediation efforts that have taken place at the quarry beginning in September 1990

  7. Norwegian millstone quarry landscapes

    Science.gov (United States)

    Heldal, Tom; Meyer, Gurli; Grenne, Tor

    2013-04-01

    Rotary querns and millstones were used in Norway since just after the Roman Period until the last millstone was made in the 1930s. Throughout all this time millstone mining was fundamental for daily life: millstones were needed to grind grain, our most important food source. We can find millstone quarries in many places in the country from coast to mountain. Some of them cover many square kilometers and count hundreds of quarries as physical testimonies of a long and great production history. Other quarries are small and hardly visible. Some of this history is known through written and oral tradition, but most of it is hidden and must be reconstructed from the traces we can find in the landscape today. The Millstone project has put these quarry landscapes on the map, and conducted a range of case studies, including characterization of archaeological features connected to the quarrying, interpretation of quarrying techniques and evolution of such and establishing distribution and trade patterns by the aid of geological provenance. The project also turned out to be a successful cooperation between different disciplines, in particular geology and archaeology.

  8. EFFECTS OF ALKALINE SANDY LOAM ON SULFURIC SOIL ACIDITY AND SULFIDIC SOIL OXIDATION

    Directory of Open Access Journals (Sweden)

    Patrick S. Michael

    2015-08-01

    Full Text Available  In poor soils, addition of alkaline sandy loam containing an adequate proportion of sand, silt and clay would add value by improving the texture, structure and organic matter (OM for general use of the soils. In acid sulfate soils (ASS, addition of alkaline sandy would improve the texture and leach out salts as well as add a sufficient proportion of OM for vegetation establishment. In this study, addition of alkaline sandy loam into sulfuric soil effectively increased the pH, lowered the redox and reduced the sulfate content, the magnitude of the effects dependent on moisture content. Addition of alkaline sandy loam in combination with OM was highly effective than the effects of the lone alkaline sandy loam. When alkaline sandy was added alone or in combination with OM into sulfidic soil, the effects on pH and the redox were similar as in the sulfuric soil but the effect on sulfate content was variable. The effects under aerobic conditions were higher than under anaerobic conditions. The findings of this study have important implications for the general management of ASS where lime availability is a concern and its application is limited.International Journal of Environment Volume-4, Issue-3, June-August 2015Page: 42-54

  9. Quarries reconditioning methodology

    International Nuclear Information System (INIS)

    Munoz, L.; Calvo, F.; Treppo, O.

    2012-01-01

    This work is about the research and the surveys carried out in the field and more than 50 quarries in Uruguay. This work consisted in the exploitation of the old excavations as well as the quarries restoring and reconditioning. The techniques of work had into consideration the environment preservation as well as the soil the fauna and the flora

  10. Multidisciplinary studies on ancient sandstone quarries of Western Sardinia (Italy).

    Science.gov (United States)

    Grillo, Silvana Maria; Del Vais, Carla; Naitza, Stefano

    2013-04-01

    , Oristano, Santa Giusta). They are prevailing fine-medium grained carbonate sandstones, and subordinate coarse sandstones and micro-conglomerates, variably cemented. In the studied areas, stratigraphic sequences grade from coarser facies of marine environment to fine-grained aeolian deposits, marked by cross-stratification. The Quaternary sedimentary sequence rests on Miocene limestones and clays, and on Plio-Pleistocene basalts. On optical microscopy, sandstones show grain-supported texture, with abundant carbonate bioclasts, intraclasts and algal nodules, with quartz, feldspars and fragments of granitoids, quartzites, volcanics. Grainsize in sandstone sequences progressively decreases towards the top, corresponding to an increase of fine bioclastic components. Terrigenous components change from the northernmost outcrops (Is Arutas quarries), where clasts of granitoid origin are dominant, to the southern outcrops (San Giovanni di Sinis quarries), which show a more marked compositional heterogeneity, with frequent volcanic feldspars and lithoclasts. The calcitic cement also shows distinct variations, both along the stratigraphic sequence and at areal scale, between the sparitic type and the micro/cryptocrystalline type. First evidences on samples from Tharros city walls indicate that sandstone blocks may come, almost in part, from the quarries of San Giovanni di Sinis that, consequently, could have started to work during the Punic age. Other evidences in the area, however, indicate that quarrying activities in Sinis continued well over the Ancient times, presumably including all the Middle Ages.

  11. Consumer-resource stoichiometry in detritus-based streams

    Science.gov (United States)

    Wyatt F. Cross; Jonathan P. Benstead; Amy D. Rosemond; J. Bruce Wallace

    2003-01-01

    Stoichiometric relationships between consumers and resources in detritus-based ecosystems have received little attention, despite the importance of detritus in most food webs. We analysed carbon (C), nitrogen (N), and phosphorus (P) content of invertebrate consumers, and basal food resources in two forested headwater streams (one reference and the other nutrient-...

  12. Geohydrology of the Gallup's Quarry area, Plainfield, Connecticut

    Science.gov (United States)

    Melvin, Robert L.; Stone, Janet Radway; Craft, Patrick A.; Lane, John W.

    1995-01-01

    The geohydrology of the Gallup's Quarry area in Plainfield, Connecticut was characterized by the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency, to provide a preliminary framework for future remedial efforts. Gallup's Quarry, an inactive sand and gravel pit, was the site of unregulated disposal of an unknown volume of chemical wastes from at least the summer of 1977 until January 1978. Existing information collected for the Connecticut Department of Environmental Protection during 1978-82 showed that ground water beneath Gallup's Quarry and adjacent land to the northwest was contaminated by organic and inorganic compounds. There is also some evidence for contamination of Mill Brook, which is located north and northwest of the disposal areas. Geologic mapping and subsurface data show that unconsolidated surficial materials up to 90 feet thick overlie fractured crystalline bedrock in most of the Gallup's Quarry area. The surficial materials consist primarily of stratified drift and till. Texture changes vertically and laterally within the stratified drift; grain size ranges from very coarse to fine. Till blankets the bedrock surface beneath the stratified drift and is a few feet to as much as 25 feet thick. Bedrock is exposed at land surface in a hill in the southeastern part of the quarry and slopes to depths of up to 90 feet beneath the area west and north of the disposal sites. The bedrock is a dark, fine-grained, fractured and jointed blastomylonite and hornblende gneiss of the Quinebaug Formation. It is likely that a west- northwest-trending fault is present in the bedrock beneath Gallup's Quarry; this fault, if present, may provide a preferential pathway for ground-water flow and contaminant transport. The principal horizontal direction of ground-water flow and movement of dissolved contaminants in the stratified drift was to the northwest of the waste-disposal areas toward Mill Brook in 1978. Estimates of average annual

  13. Energy values of suspended detritus in Andaman Sea

    Digital Repository Service at National Institute of Oceanography (India)

    Krishnakumari, L.; Royan, J.P.; Sumitra-Vijayaraghavan

    Energy content of suspended detritus was determined in Andaman Sea waters during April-May 1988. The caloric content of suspended detritus ranged from 987 to 7040 cal. per gram dry wt with an average value of 5530 cal. per gram dry wt. The results...

  14. Shielding features of quarry stone

    International Nuclear Information System (INIS)

    Hernandez V, C.; Contreras S, H.; Hernandez A, L.; Baltazar R, A.; Escareno J, E.; Mares E, C. A.; Vega C, H. R.

    2010-10-01

    Quarry stone lineal attenuation coefficient for gamma-rays has been obtained. In Zacatecas, quarry stone is widely utilized as a decorative item in buildings, however its shielding features against gamma-rays unknown. The aim of this work is to determine the shielding properties of quarry stone against γ-rays using Monte Carlo calculations where a detailed model of a good geometry experimental setup was carried out. In the calculations 10 pieces 10 X 10 cm 2 of different thickness were utilized to evaluate the photons transmission as the quarry stone thickness is increased. It was noticed that transmitted photons decay away as the shield thickness is increased, these results were fitted to an exponential function were the linear attenuation coefficient was estimated. Also, using XCOM code the linear attenuation coefficient from several keV up to 100 MeV was estimated. From the comparison between Monte Carlo results and XCOM calculations a good agreement was found. For 0.662 MeV γ-rays the attenuation coefficient of quarry stone, whose density is 2.413 g-cm -3 , is 0.1798 cm -1 , this mean a X 1/2 = 3.9 cm, X 1/4 = 7.7 cm, X 1/10 = 12.8 cm, and X 1/100 = 25.6 cm. Having the information of quarry stone performance as shielding give the chance to use this material to shield X and γ-ray facilities. (Author)

  15. Production of litter and detritus related to the density of mangrove

    Science.gov (United States)

    Budi Mulya, Miswar; Arlen, HJ

    2018-03-01

    Research about the production of leaf litter and detritus related to the density of mangrove trees has been done. The aims of this research are to know and analyze the amount of litter and detritus produced to the density of mangrove trees. The production and collection of leaf litter were carried out in five stations. Production of detritus and decomposition rate were calculated by measuring its dry weight. The density and level of mangrove trees were determined using transect quadratic method. The relationship between the leaf litter and detritus production ratio related to mangrove density were then analyzed. Results showed that mangrove trees with the density of 766.67 ind ha‑1 ccould produce the amount of litter and detritus to about 28597.33 gha‑1day‑1and 1099.35 gha‑1day‑1 while mangrove trees with the density of 1300 ind ha‑1 could produce the amount of litter and detritus to about 35093.33 g/ha/day and 1216.68 gha‑1day‑1 respectively. Data analysis showed that the increment of mangrove density is linearly related to the production increment of litter and detritus.

  16. Effect of Irrigation Water Type on Infiltration Rates of Sandy Soil

    International Nuclear Information System (INIS)

    Al-Omran, A.M.; Al-Matrood, S.M.; Choudhary, M.I.

    2004-01-01

    A laboratory experiment was conducted to test the effect of three water types (tap water, well water and sewage water) on the infiltration rate of three soils varying in texture (sand. loamy sand and sandy loam). A stationary rainfall simulator dispensing water at a rate of 45 mm h-1, connected to the different sources of water, was used to measure the infiltration rates. A total of 5 runs were carried out using each water quality. The volume of runoff against the time was recorded at each 5 minute interval. The infiltration rate was calculated as the difference between the water applied and the excesses water measured as surface runoff. Infiltration rate at first run were rapid in all the three soils and then progressively declined as the number of runs increased. The same trend was observed for each water quality tested. The reduction in infiltration rate with increasing number of runs for prewetted surface than for the initial dry surface was attributed to break down and settling of fine particles that took place earlier during prewetting. The infiltration curves for all the three soils when irrigared with different qualities of water was not distinguishable. The relationship between infiltration rate as function of time for the treatments applied were tested using Kostiakov equation I=bt-n. The infiltration data gave a coefficient of determination R2 >0.90 for all the treatments. The infiltration parameters B, and n varied strongly with respect to soil texture. Values of B decreased with changing soil textures, being highest for the sandy soil, and lowest for the sandy loamy soil, whereas n values showed the opposite trend. It was concluded that effect of soil texture on the infiltration rate was very pronounced while water qualities showed a little effect. (author)

  17. Quarrying: an anthropogenic geomorphological approach

    International Nuclear Information System (INIS)

    David, L.

    2008-01-01

    The study intends to give an introduction to the significance of quarrying from the point of view of anthropogenic geomorphology, indicating the level of surface forming due to the mining of mineral raw materials. The significance of this topic is supported by the existence of the so-called 'mining landscapes' that emerged since to the 19 th century. Authors focus on the geomorphic impact of quarrying with special emphasis on factors influencing its spatial distribution, as well as on the characteristics and classification of surface features produced by quarrying, providing an overview of the most important excavated and accumulated forms and form components, on the macro, meso and micro scales. Finally, international and Hungarian case studies illustrate some aspects of the opening and after-use of mining sites in order to observe how abandoned quarries can be turned into 'environmental values', and used as possible sites for exhibitions or for regional and tourism development projects. (author)

  18. Differences in the surface texture of aggregate particles determined by 3D model derived from optic microscope measurements

    Directory of Open Access Journals (Sweden)

    Jozef Komačka

    2015-12-01

    Full Text Available The surface texture of aggregate particles was investigated based on the 3D model of surface generated from the measurements by optic microscope. New software MicroSYS was developed to determine the wrapping plane of 3D model of aggregate using the function called “Thin plate spline“. New parameter for evaluation of surface texture of aggregate particle was proposed as the volumetric difference between two planes (wrapping plane and aggregate surface. Applicability of this parameters was tested on two aggregate fractions (4/8 and 8/11 coming form 11 quarries in Slovakia. The tested aggregates differed from petrography point of view and ranged from soft to hard. The difference among the quarries and also between fractions of aggregate was found out. The better surface texture was observed for the finner fraction of aggregate. Simultaneously, the better results were determined in the case of aggregate produced from the ingeous intrusive or extrusive rocks comparing to the sedimentary carbonate rocks aggregate.

  19. Analyzing the Sand-fixing Effect of Feldspathic Sandstone from the Texture Characteristics

    Science.gov (United States)

    Zhang, lu; Ban, Jichang

    2018-01-01

    The purpose of this research was aimed to study the sand fixing effect of feldspathic sandstone in Mu Us Sandy Land, to provide a scienticic basis for desertification control, soil and water conservation and development of farming there. Methods of mixing feldspathic sandstone and aeolian sandy soil according to 1: 0, 1: 1, 1: 2, 1: 5, and 0: 1 mass ratioes, the graded composition and characteristics were studied with laser particle size analyzer. The result showed that these features of sand-based, loosely structured, easy to wind erosion of aeolian sandy soil were changed before feldspathic sandstone and aeolian sandy soil compounding. The <0.05 mm particle mass increased with feldspathic sandstone mass increasing. The texture presented this kind of change from sand to sandy loam to loam to silt loam. The small particle size distribution, good homogeneity and other features of aeolian sandy soil were improved to a certain degree, and the particle size distribution became broad before feldspathic sandstone and aeolian sandy soil compounding. The particle grading was continuous, and the grading characteristic was good when m(F): m(S) was 1: 5(Cu was 54.71 and Cc was 2.54) or when m(F): m(S) was 1: 2(Cu was 76.21, Cc was 1.12). The conclusion is that feldspathic sandstone has sand-fixing effect in texture characteristics, which heightens with feldspathic sandstone mass increasing, and when the mass ratio of feldspathic sandstone: aeolian sandy soil is 1: 2 or 1: 5 which compound better.

  20. Anciet marble quarries in Lesvos island Greece

    Science.gov (United States)

    Mataragkas, M.; Mataragkas, D.

    2009-04-01

    ANCIENT MARBLE QUARRIES IN LESBOS ISLAND, GREECE Varti- Matarangas M.1 & Matarangas D. 1 Institute of Geological and Mining Exploration (IGME), Olympic Village, Entrance C, ACHARNAE 13677, GREECE myrsini@igme.gr , myrsini@otenet.g r A B S T R A C T Ten ancient marble quarries of Lesbos Island, most of them previously unknown, have been studied, in the frame of the research study on the ancient marble quarries in the Aegean Sea. In the present paper the geological, petrological and morphological features of the aforementioned quarries are examined. Concerning the six ancient quarries located in the areas of Tarti, Agia Paraskevi (Tsaf), Mageiras, Loutra, Latomi (Plomari) and Thermi, the authochthonous neopaleozoic unit constitutes their geological formation, while their hosting lithological formations are the included crystalline limestone lens like beds. In two ancient quarries in the areas Moria and Alyfanta, the geological formation is the authochthonous upper Triassic series and the hosting lithological formation the upper Triassic carbonate sequence, while in the areas of Akrasi-Abeliko and Karyni, the geological formation is the thrust Triassic unit and the lithological hosting formations are the included strongly deformed or not crystalline limestone lenticular beds. Furthermore, the petrographic features were also determined permitting the identification of the building stones that have been used.

  1. 1998 mines and quarries guidebook

    International Nuclear Information System (INIS)

    1998-01-01

    The 1998 edition of the mines and quarries guidebook provides: a comprehensive overview of mining activities in France and French-speaking countries relative to coal, uranium, non-ferrous ores and metals, industrial minerals, lime, limestone, silica, cermet and saline minerals; a list of recycling companies; a list of quarries and building material exploitations (organisational structure of main companies, granulates, cement industry, gypsum, plaster, tiles, bricks, stones..); a list and coordinates by department of more than 1400 quarries with the material exploited; an inventory of mining exploitations of Belgium, Switzerland and French speaking countries of Africa, a listing and organisational structure of research and engineering centres and administrations; an alphabetical and analytical repertory of more than 700 supplying companies of the mineral industry; and the status, organization and members of the mineral industry society. (J.S.)

  2. Sand quarry wetlands provide high-quality habitat for native amphibians

    Directory of Open Access Journals (Sweden)

    M. Sievers

    2017-05-01

    Full Text Available Anthropogenic disturbances to habitats influence the fitness of individual animals, the abundance of their populations, and the composition of their communities. Wetlands in particular are frequently degraded and destroyed, impacting the animals that inhabit these important ecosystems. The creation of wetlands during and following sand extraction processes is inevitable, and thus, sand quarries have the potential to support aquatic animals. To determine how amphibians utilise these wetlands, I conducted nocturnal call surveys at wetlands within the Kables Sands quarry, New South Wales, Australia, and within surrounding reference wetlands, and quantified levels of developmental instability (DI as a proxy for fitness. Whilst quarry and reference wetlands were largely similar in terms of environmental characteristics, quarry wetlands consistently harboured more amphibian species and individuals. Using unsigned asymmetry as a measure of DI, frogs from the quarry sites exhibited significantly lower levels of DI compared to reference wetlands, indicating that quarry wetlands may be comparatively higher quality. Levels of DI within quarry wetlands also compared favourably to data from healthy frog populations extracted from the literature. Further enhancing the suitability of quarry wetlands would require minimal effort, with potentially significant increases in local and regional biodiversity. Documenting species presence and quantifying individual fitness by measuring limb lengths is an economically and logistically feasible method to assess the health of quarry wetlands. Overall, the methods outlined here provide a powerful, yet simple, tool to assess the overall health and suitability of quarry wetlands that could be easily adopted at quarries throughout the world.

  3. Determination of diffusion coefficients in cohesive and sandy sediment from the area of Gorleben

    International Nuclear Information System (INIS)

    Klotz, D.

    1989-01-01

    The cohesive and sandy sediments stem from shaft driving at the Gorleben salt done. For the cohesive materials, HTD was used as a tracer substance, while I-131 - was used for the sandy materials. Diffusion coefficients of HTD in cohesive materials in their natural texture are in the range of 2x10 -6 to 5x10 -6 cm 2 /s, those of I-131 - in the investigated uniform fine and middle sands are approximately 3x10 -6 cm 2 /s. (DG) [de

  4. Strength Characteristics of Fiber Reinforced Quarry Dust Stabilized Fly Ash

    OpenAIRE

    Akshaya Kumar Sabat; Bidula Bose

    2015-01-01

    Effects of quarry dust and polypropylene fiber on compaction properties, shear strength parameters, and California bearing ratio (CBR) of a fly ash have been discussed in this paper. Quarry dust was added to a fly ash from 0 to 60% at an increment of 10%, compaction and soaked CBR tests were conducted on fly ash-quarry dust mixes and the optimum percentage of quarry dust was found out to be 40%. Polypropylene fiber was added to fly ash stabilized with optimum percentage of quarry dust, from 0...

  5. Mineralization of surfactants by the microbiota of submerged plant detritus.

    Science.gov (United States)

    Federle, T W; Ventullo, R M

    1990-02-01

    In wetlands and canopied bodies of water, plant detritus is an important source of carbon and energy. Detrital materials possess a large surface area for sorption of dissolved organics and are colonized by a large and diverse microbiota. To examine the biodegradation of surfactants by these microorganisms, submerged oak leaves were obtained from a laundromat wastewater pond, its overflow, and a pristine control pond. Leaves were cut into disks and incubated in sterile water amended with 50 mug of C-labeled linear alkylbenzene sulfonate (LAS), linear alcohol ethoxylate, stearyltrimethyl ammonium chloride, distearyldimethyl ammonium chloride, benzoic acid, or mixed amino acids per liter. Sorption of the test compounds to the detritus and evolution of CO(2) were followed with time. All of the compounds sorbed to the detritus to various degrees, with LAS and stearyltrimethyl ammonium chloride the most sorptive and benzoic acid the least. All compounds were mineralized without a lag. With leaves from the laundromat wastewater pond, half-lives were 12.6 days for LAS, 8.4 days for linear alcohol ethoxylate, 14.2 days for stearyltrimethyl ammonium chloride, 1.0 days for benzoic acid, and 2.7 days for mixed amino acids. Mineralization of LAS and linear alcohol ethoxylate by control pond leaves was slower and exhibited an S-shaped rather than a typical first-order pattern. This study shows that detritus represents a significant site of surfactant removal in detritus-rich systems.

  6. Mineralization of surfactants by the microbiota of submerged plant detritus

    International Nuclear Information System (INIS)

    Federle, T.W.; Ventullo, R.M.

    1990-01-01

    In wetlands and canopied bodies of water, plant detritus is an important source of carbon and energy. Detrital materials possess a large surface area for sorption of dissolved organics and are colonized by a large and diverse microbiota. To examine the biodegradation of surfactants by these microorganisms, submerged oak leaves were obtained from a laundromat wastewater pond, its overflow, and a pristine control pond. Leaves were cut into disks and incubated in sterile water amended with 50 μg of 14 C-labeled linear alkylbenzene sulfonate (LAS), linear alcohol ethoxylate, stearyltrimethyl ammonium chloride, distearyldimethyl ammonium chloride, benzoic acid, or mixed amino acids per liter. Sorption of the test compounds to the detritus and evolution of 14 CO 2 were followed with time. All of the compounds sorbed to the detritus to various degrees, with LAS and stearyltrimethyl ammonium chloride the most sorptive and benzoic acid the least. All compounds were mineralized without a lag. With leaves from the laundromat wastewater pond, half-lives were 12.6 days for LAS, 8.4 days for linear alcohol ethoxylate, 14.2 days for stearyltrimethyl ammonium chloride, 1.0 days for benzoic acid, and 2.7 days for mixed amino acids. Mineralization of LAS and linear alcohol ethoxylate by control pond leaves was slower and exhibited an S-shaped rather than a typical first-order pattern. This study shows that detritus represents a significant site of surfactant removal in detritus-rich systems

  7. Monitoring Quarry Area with Landsat Long Time-Series for Socioeconomic Study

    Directory of Open Access Journals (Sweden)

    Haoteng Zhao

    2018-03-01

    Full Text Available Quarry sites result from human activity, which includes the removal of original vegetation and the overlying soil to dig out stones for building use. Therefore, the dynamics of the quarry area provide a unique view of human mining activities. Actually, the topographic changes caused by mining activities are also a result of the development of the local economy. Thus, monitoring the quarry area can provide information about the policies of the economy and environmental protection. In this paper, we developed a combined method of machine learning classification and quarry region analysis to estimate the quarry area in a quarry region near Beijing. A temporal smoothing based on the classification results of all years was applied in post-processing to remove outliers and obtain gently changing sequences along the monitoring term. The method was applied to Landsat images to derive a quarry distribution map and quarry area time series from 1984 to 2017, revealing significant inter-annual variability. The time series revealed a five-stage development of the quarry area with different growth patterns. As the study region lies on two jurisdictions—Tianjin and Hebei—a comparison of the quarry area changes in the two jurisdictions was applied, which revealed that the different policies in the two regions could impose different impacts on the development of a quarry area. An analysis concerning the relationship between quarry area and gross regional product (GRP was performed to explore the potential application on socioeconomic studies, and we found a strong positive correlation between quarry area and GRP in Langfang City, Hebei Province. These results demonstrate the potential benefit of annual monitoring over the long-term for socioeconomic studies, which can be used for mining decision making.

  8. Pump Hydro Energy Storage systems (PHES) in groundwater flooded quarries

    Science.gov (United States)

    Poulain, Angélique; de Dreuzy, Jean-Raynald; Goderniaux, Pascal

    2018-04-01

    Pump storage hydroelectricity is an efficient way to temporarily store energy. This technique requires to store temporarily a large volume of water in an upper reservoir, and to release it through turbines to the lower reservoir, to produce electricity. Recently, the idea of using old flooded quarries as a lower reservoir has been evoked. However, these flooded quarries are generally connected to unconfined aquifers. Consequently, pumping or injecting large volumes of water, within short time intervals, will have an impact on the adjacent aquifers. Conversely, water exchanges between the quarry and the aquifer may also influence the water level fluctuations in the lower reservoir. Using numerical modelling, this study investigates the interactions between generic flooded open pit quarries and adjacent unconfined aquifers, during various pump-storage cyclic stresses. The propagation of sinusoidal stresses in the adjacent porous media and the amplitude of water level fluctuations in the quarry are studied. Homogeneous rock media and the presence of fractures in the vicinity of the quarry are considered. Results show that hydrological quarry - rock interactions must be considered with caution, when implementing pump - storage systems. For rock media characterized by high hydraulic conductivity and porosity values, water volumes exchanges during cycles may affect significantly the amplitude of the water level fluctuations in the quarry, and as a consequence, the instantaneous electricity production. Regarding the impact of the pump - storage cyclic stresses on the surrounding environment, the distance of influence is potentially high under specific conditions, and is enhanced with the occurrence of rock heterogeneities, such as fractures. The impact around the quarry used as a lower reservoir thus appears as an important constraining factor regarding the feasibility of pump - storage systems, to be assessed carefully if groundwater level fluctuations around the quarry

  9. Prediction of Performance of Diamond Wire Saw with Respect to Texture Characteristics of Rock / Prognozowanie Wydajności Pracy Strunowej Piły Diamentowej W Odniesieniu Do Charakterystyki Tekstury Skał

    Science.gov (United States)

    Ghaysari, N.; Ataei, M.; Sereshki, F.; Mikaiel, R.

    2012-12-01

    In this study, prediction of production rate in diamond wire saw has been investigated. Performance measurements of diamond wire saw carried out in 7 different quarries of carbonate rocks in Iran. For determination textural properties, rock samples were collected from these quarries. At first, a thin section was prepared for each rock and then 5 digital photographs were taken from each section. After this, all images were digitized using AutoCAD software. Then, area, perimeter, longest diameter and shortest diameter were assigned. According to these parameters, all of the other textural characteristics and texture coefficient were determined too. The correlation between sawing rate and textural characteristics were evaluated using multiple and simple regression analyses. Then developed model was validated by P-value test. It was concluded that area, perimeter, diameter equivalent and index of grain size homogeneity are very effective on production rate. Production rate using diamond wire saw can reliably be predicted using developed model.

  10. Sinkhole development induced by underground quarrying, and the related hazard

    Science.gov (United States)

    Parise, M.; Delle Rose, M.

    2009-04-01

    Sinkholes are extremely widespread in Apulia, a very flat and carbonate region, that acted as the foreland during the phases of building up of the Southern Apenninic Chain in Miocene time. This is due to the presence of soluble rocks throughout the region, that highly predispose the area to this very subtle natural hazard. In addition to the natural setting, which favours their development, sinkholes may also be induced by anthropogenic activities. In the latter sense, underground quarrying represents one of the most dangerous activities in karst areas. Apulia has a long history of quarrying. Since the roman time, the local rocks, from the Cretaceous micritic limestones to the Quaternary calcarenites, have been intensely quarried and used as building and ornamental materials. In several settings of the region, the rocks with the best petrographic characteristics are located at depths ranging from a few to some tens of meters. This caused the opening of many underground quarries, and the development of a complex network of subterranean galleries. Underground quarrying had a great impulse at the turn between the XIX and the XX century, when a large number of quarries was opened. Later on, after the Second World War, most of the quarries were progressively abandoned, even because of the first signs of instability, both underground and at the ground surface. With time, the memory of the presence and development of the underground quarries was progressively lost, with severe repercussions on the safety of the land above the excavated areas. Lack of knowledge of the subterranean pattern of galleries, combined with the expansion of the built-up areas at the surface, resulted in increasing significantly the vulnerability of exposed elements at risk. Events such as the 29 March, 2007, at Gallipoli only by chance did not result in any casualties, when a 15-mt wide and 5-mt deep sinkhole opened in a few hours at a road crossing, above the site of an old underground quarry

  11. Landscape evolution by subglacial quarrying

    Science.gov (United States)

    Ugelvig, Sofie V.; Egholm, David L.; Iverson, Neal R.

    2014-05-01

    In glacial landscape evolution models, subglacial erosion rates are often related to basal sliding or ice discharge by a power-law. This relation can be justified for bedrock abrasion because rock debris transported in the basal ice drives the erosion. However, a simple relation between rates of sliding and erosion is not well supported when considering models for quarrying of rock blocks from the bed. Iverson (2012) introduced a new subglacial quarrying model that operates from the theory of adhesive wear. The model is based on the fact that cavities, with a high level of bedrock differential stress, form along the lee side of bed obstacles when the sliding velocity is to high to allow for the ice to creep around the obstacles. The erosion rate is quantified by considering the likelihood of rock fracturing on topographic bumps. The model includes a statistical treatment of the bedrock weakness: larger rock bodies have lower strengths since they have greater possibility of containing a large flaw [Jaeger and Cook, 1979]. Inclusion of this effect strongly influences the erosion rates and questions the dominant role of sliding rate in standard models for subglacial erosion. Effective pressure, average bedslope, and bedrock fracture density are primary factors that, in addition to sliding rate, influence the erosion rate of this new quarrying model [Iverson, 2012]. We have implemented the quarrying model in a depth-integrated higher-order ice-sheet model [Egholm et al. 2011], coupled to a model for glacial hydrology. In order to also include the effects of cavitation on the subglacial sliding rate, we use a sliding law proposed by Schoof (2005), which includes an upper limit for the stress that can be supported at the bed. Computational experiments show that the combined influence of pressure, sliding rate and bed slope leads to realistically looking landforms such as U-shaped valleys, cirques, hanging valleys and overdeepenings. Compared to model results using a

  12. Effect of soil texture on phytoremediation of arsenic-contaminated soils

    Science.gov (United States)

    Pallud, C. E.; Matzen, S. L.; Olson, A.

    2015-12-01

    Soil arsenic (As) contamination is a global problem, resulting in part from anthropogenic activities, including the use of arsenical pesticides and treated wood, mining, and irrigated agriculture. Phytoextraction using the hyperaccumulating fern Pteris vittata is a promising new technology to remediate soils with shallow arsenic contamination with minimal site disturbance. However, many challenges still lie ahead for a global application of phytoremediation. For example, remediation times using P. vittata are on the order of decades. In addition, most research on As phytoextraction with P. vittata has examined As removal from sandy soils, where As is more available, with little research focusing on As removal from clayey soils, where As is less available. The objective of this study is to determine the effects of soil texture and soil fertilization on As extraction by P. vittata, to optimize remediation efficiency and decrease remediation time under complex field conditions. A field study was established 2.5 years ago in an abandoned railroad grade contaminated with As (average 85.5 mg kg-1) with texture varying from sandy loam to silty clay loam. Organic N, inorganic N, organic P, inorganic P, and compost were applied to separate sub-plots; control ferns were grown in untreated soil. In a parallel greenhouse experiment, ferns were grown in sandy loam soil extracted from the field (180 mg As kg-1), with similar treatments as those used at the field site, plus a high phosphate treatment and treatments with arbuscular mycorrhizal fungi. In the field study, fern mortality was 24% higher in clayey soil than in sandy soil due to waterlogging, while As was primarily associated with sandy soil. Results from the sandy loam soil indicate that soil treatments did not significantly increase As phytoextraction, which was lower in phosphate-treated ferns than in control ferns, both in the field and greenhouse study. Under greenhouse conditions, ferns treated with organic N were

  13. Changes in N cycling induced by Ulva detritus enrichment of sediments

    DEFF Research Database (Denmark)

    Garcia-Robledo, Emilio; Revsbech, Niels Peter; Risgaard-Petersen, Nils

    2013-01-01

    Macroalgal accumulation and decomposition in shallow water environments typically result in an increase in the organic matter content of the sediment, affecting both benthic metabolism and nutrient dynamics. The present study investigates how a pulse addition of Ulva detritus to estuarine sediment...... of oxygen and nitrate. Nitrification increased significantly in response to enhanced NH4 + supply from decomposition of the Ulva detritus. Aerobic ammonia oxidation exceeded rates of nitrite oxidation, leading to accumulation of NO2 − in the oxic zone of the sediment. Nitrite and NO3 − produced via...... nitrification diffused up to the sediment surface, inducing a net efflux to the water column, and downwards, supporting a high rate of denitrification coupled to nitrification. The present study shows that organic enrichment with Ulva detritus enhances sediment oxygen uptake, nitrification and denitrification...

  14. Shedding light on detritus: Interactions between invertebrates, bacteria and substrates in benthic habitats

    NARCIS (Netherlands)

    Hunting, E.R.

    2013-01-01

    The processing of dead organic matter, also known as detritus, is a central ecosystem process driven by detritus feeding organisms that are mostly located at the bottom of water bodies where dead organic matter (OM) accumulates. Detritivorous organisms form communities composed of invertebrates,

  15. Exploitation program of ''Adamow'' quarry up to 2015

    International Nuclear Information System (INIS)

    Hadlaw, A.

    1994-01-01

    The brown coal deposits exploited by the quarry ''Adamow'' located in Central Poland are shortly described and the prognosis of their exploitation up to 2015 is given. The basis data on the perspective deposits in the quarry's area are also presented. All deposits are shown on the map. 3 ills, 2 tabs

  16. Strength Characteristics of Quarry Dust in Replacement of Sand

    Science.gov (United States)

    Shyam Prakash, K.; Hanumantha Rao, Ch, Dr

    2017-08-01

    The replacement of natural fine aggregate by using quarry dust leads to consumption of generated quarry dust, the requirement of land fill area can be reduced and solves the natural sand scarcity problem. The sand availability as a fine aggregate at low cost which needs the reason to search as a alternative material. Even it causes saddle to dump the crusher dust at one place which causes environmental pollution. The chemical analysis, specific gravity, sieve analysis and compressive strength is identified for various percentage and grades of concrete by replacement of sand with quarry dust.

  17. Sustainable closure of construction materials quarries in Cuba

    Directory of Open Access Journals (Sweden)

    Julio Montero-Matos

    2017-10-01

    Full Text Available The inclusion of effective mine closure plans in the exploitation project is the way to compensate for the harmful effect of this activity. Based on a diagnosis carried out in 11 sites in operation, belonging to the company Canteras, a methodology was designed with a systemic and integral approach that consists of five stages and allows the execution of quarry closures in a sustainable manner. The Delphi method was applied to select the criteria that directly affect the sustainable closure of quarries in such a way that it considers the essential postulates of the Cuban Economic Model (MEC. The proposed methodology represents a contribution to the planning and design of the mining closure in Cuban non-metallic deposits to guarantee the reduction of the environmental impacts caused during its operation and the reduction, to the lesser extent possible, of negative socio-economic effects for the workers and the community located in the area of influence of the quarries. Currently applied in the quarry of San José, in Mayabeque province.

  18. Quarry Haul Road Ecological Survey

    International Nuclear Information System (INIS)

    1992-09-01

    This biological survey was performed to document the summer flora and fauna found along the haul road constructed as part of the remedial action for the quarry bulk waste. State and Federal species listed as threatened or endangered were noted if encountered while surveying. Sampling locations were equally spaced along the quarry haul road, and a survey for vegetation and birds conducted at each location. Bird observations were conducted as breeding bird surveys once in June of 1991, and again in June of 1992. Each year's survey includes two observations in the early morning and one late in the evening. Vegetation surveys were conducted in 1991 using quadrants and transects. mammal, reptile, and amphibian sightings were noted as encountered

  19. Nutrient enrichment alters storage and fluxes of detritus in a headwater stream ecosystem

    Science.gov (United States)

    Jonathan P. Benstead; Amy D. Rosemond; Wyatt F. Cross; J. Bruce Wallace; Susan L. Eggert; Keller Suberkropp; Vladislav Gulis; Jennifer L. Greenwood; Cynthia J. Tant

    2009-01-01

    Responses of detrital pathways to nutrients may differ fundamentally from pathways involving living plants: basal carbon resources can potentially decrease rather than increase with nutrient enrichment. Despite the potential for nutrients to accelerate heterotrophic processes and fluxes of detritus, few studies have examined detritus-nutrient dynamics at whole-...

  20. [Influence of a new phosphoramide urease inhibitor on urea-N transformation in different texture soil].

    Science.gov (United States)

    Zhou, Xuan; Wu, Liang Huan; Dai, Feng

    2016-12-01

    Addition of urease inhibitors is one of the important measures to increase nitrogen (N) use efficiency of crop, due to retardant of urea hydrolysis and reduction of ammonia volatilization loss. An incubation experiment was conducted to investigate the urease inhibition effect of a new phosphoramide urease inhibitor, NPPT (N-(n-propyl) thiophosphoric triamide) in different texture soils under dark condition at 25 ℃, and NBPT (N-(n-butyl) thiophosphoric triamide) was obtained to compare the inhibition effect on urease in different soil textures by different dosages of urea adding. Results showed that the effective reaction time of urea was less than 9 d in the loamy and clay soil. Addition of inhibitors for retardation of urea hydrolysis was more than 3 d. In sandy soil, urea decomposition was relatively slow, and adding inhibitor significantly inhibited soil urease acti-vity, and reduced NH 4 + -N content. During the incubation time, the inhibition effect of high dosage urea in the soil was better than that of low dosage. At day 6, the urease inhibition rate of NBPT and NPPT (N 250 mg·kg -1 ) were 56.3% and 53.0% in sandy soil, 0.04% and 0.3% in loamy soil, 4.1% and 6.2% in clay soil; the urease inhibition rate of NBPT and NPPT (N 500 mg·kg -1 ) were 59.4% and 65.8% in sandy soil, 14.5% and 15.1% in loamy soil, 49.1% and 48.1% in clay soil. The urease inhibition effects in different texture soil were in order of sandy soil > clay soil> loamy soil. The soil NH 4 + -N content by different inhibitors during incubation time increased at first and then decreased, while soil NO 3 - -N content and apparent nitrification rate both showed rising trends. Compared with urea treatment, addition of urease inhibitors (NBPT and NPPT) significantly increased urea-N left in the soil and reduced NH 4 + -N content. In short, new urease inhibitor NPPT in different texture is an effective urease inhibitor.

  1. ASSESSING LAND COVER CHANGES CAUSED BY GRANITE QUARRYING USING REMOTE SENSING

    Directory of Open Access Journals (Sweden)

    R. S. Moeletsi

    2017-11-01

    Full Text Available Dimension stone quarrying in the area between Rustenburg and Brits in the North West Province of South Africa has been in existence for over 70 decades. The unique characteristics of the granite deposits in South Africa resulted in making the country a global producer of the granite rocks. This led to intensified quarrying activities between Rustenburg and Brits town. However, this surface mining method, has a potential to impact the environment in a negative way causing loss in vegetation, depletion of natural resources, loss of scenic beauty and contamination of surface water resources. To assess the land cover changes caused by granite quarrying activities, remotely sensed data in the form of Landsat images between 1998 and 2015 were used. Supervised classification was used to create maps. Accuracy assessment using Google EarthTM as a reference data yielded an overall accuracy of 78 %. The post classification change detection method was used to assess land cover changes within the granite quarries. Granite quarries increased by 1174.86 ha while formation of quarry lakes increased to 5.3 ha over the 17-year period. Vegetation cover decreased by 1308 ha in area while 18.3 ha bare land was lost during the same period. This study demonstrated the utility of remote sensing to detect changes in land cover within granite quarries.

  2. Interactions between Soil Texture and Placement of Dairy Slurry Application

    DEFF Research Database (Denmark)

    Glæsner, Nadia; Kjærgaard, Charlotte; Rubæk, Gitte Holton

    2011-01-01

    soils. We compared leaching of slurry-applied bromide through intact soil columns (20 cm diam., 20 cm high) of differing textures following surface application or injection of slurry. The volumetric fraction of soil pores >30 μm ranged from 43% in a loamy sand to 28% in a sandy loam and 15% in a loam...... physical protection against leaching of bromide was reflected by 60.2% of the bromide tracer was recovered in the effluent after injection, compared with 80.6% recovery after surface application. No effect of slurry injection was observed in the loamy sand and sandy loam soils. Our findings point to soil...

  3. Multi-Criteria Decision Analysis for an Abandoned Quarry in the Evros Region (NE Greece

    Directory of Open Access Journals (Sweden)

    Sapfo Τsolaki-Fiaka

    2018-04-01

    Full Text Available The purpose of this study is to identify the impacts of abandoned quarries and to examine scenarios for their restoration. Two quarries were selected as case studies, which are located in the Evros Region (NE Greece. Initially, the current state of the abandoned quarries was recorded and evaluated, including slopes, landscape, land use, as well as cultural elements. Four alterative scenarios for the exploitation of each quarry were proposed, taking into account the specifics of each site. Financial, environmental, and socioeconomic criteria were then used to evaluate these scenarios. The PROMETHEE method is a multi-criteria decision analysis approach and was applied to rank the alterative scenarios. The results show that the “do nothing” scenario is the worst solution for both quarries. In the quarry at Αsvestades, the restoration of the area by returning the land to pre-quarry use with the shaping of the slopes and planting is considered the best solution. On the other hand, in the quarry Mikro Derio two scenarios are proposed; one provides restoring the site to its pre-quarry land use and the other is the restoration of the quarry combined with the creation of a wildlife observatory and places for alternative forms of tourism.

  4. Overdeepening development in a glacial landscape evolution model with quarrying

    DEFF Research Database (Denmark)

    Ugelvig, Sofie Vej; Egholm, D.L.; Iverson, Neal R.

    In glacial landscape evolution models, subglacial erosion rates are often related to basal sliding or ice discharge by a power-law. This relation can be justified when considering bed abrasion, where rock debris transported in the basal ice drives erosion. However, the relation is not well...... supported when considering models for quarrying of rock blocks from the bed. Field observations indicate that the principal mechanism of glacial erosion is quarrying, which emphasize the importance of a better way of implementing erosion by quarrying in glacial landscape evolution models. Iverson (2012...... around the obstacles. The erosion rate is quantified by considering the likelihood of rock fracturing on topographic bumps. The model includes a statistical treatment of the bedrock weakness, which is neglected in previous quarrying models. Sliding rate, effective pressure, and average bedslope...

  5. Detritus fuels ecosystem metabolism but not metazoan food webs in San Francisco estuary's freshwater delta

    Science.gov (United States)

    Sobczak, W.V.; Cloern, J.E.; Jassby, A.D.; Cole, B.E.; Schraga, T.S.; Arnsberg, A.

    2005-01-01

    Detritus from terrestrial ecosystems is the major source of organic matter in many streams, rivers, and estuaries, yet the role of detritus in supporting pelagic food webs is debated. We examined the importance of detritus to secondary productivity in the Sacramento and San Joaquin River Delta (California, United States), a large complex of tidal freshwater habitats. The Delta ecosystem has low primary productivity but large detrital inputs, so we hypothesized that detritus is the primary energy source fueling production in pelagic food webs. We assessed the sources, quantity, composition, and bioavailability of organic matter among a diversity of habitats (e.g., marsh sloughs, floodplains, tidal lakes, and deep river channels) over two years to test this hypothesis. Our results support the emerging principle that detritus dominates riverine and estuarine organic matter supply and supports the majority of ecosystem metabolism. Yet in contrast to prevailing ideas, we found that detritus was weakly coupled to the Delta's pelagic food web. Results from independent approaches showed that phytoplankton production was the dominant source of organic matter for the Delta's pelagic food web, even though primary production accounts for a small fraction of the Delta's organic matter supply. If these results are general, they suggest that the value of organic matter to higher trophic levels, including species targeted by programs of ecosystem restoration, is a function of phytoplankton production. ?? 2005 Estuarine Research Federation.

  6. OCCUPATIONAL HEALTH HAZARDS AMONG QUARRY ...

    African Journals Online (AJOL)

    Key Words: Occupational health hazards, Industrial pollution, Quarry industry, ... fireworks and signaling apparatus and for setting blind rivets and forming ... in the air, physiological risks and psychological trauma (Ajayi & Osibanjo, 1995).

  7. The Effects of Detritus Input on Soil Organic Matter Content and Carbon Dioxide Emission in a Central European Deciduous Forest

    Directory of Open Access Journals (Sweden)

    FEKETE, István

    2011-01-01

    Full Text Available A major objective of our research was to survey soil biological activity and organic mattercontent reduction in a Central European oak forest during treatments of various detritus inputs within theSíkfkút DIRT (Detritus Input and Removal Treatments Project. Beside the control, three detritusremoval and two detritus duplication treatments were applied. Our examinations have proven that soilorganic matter content declined relatively fast in detritus removal treatments. The reduction wasespecially remarkable in root detritus removal treatments, where – due to the lack of transpiration – soilswere moister during the whole year than in the other treatments. The higher moisture content, despite ofthe reduction of detritus input, produced an intense soil respiration. This can be explained by the fact thatdecomposing organisms have increased the use of soil organic matter. Detritus input reduction had asignificantly greater effect on soil respiration and organic matter content than detritus input duplicationof the same extent. The latter did not cause any significant change compared to the control.

  8. Utilization of muddy detritus as organic matter source by the fan mussel Pinna nobilis.

    Directory of Open Access Journals (Sweden)

    S. TRIGOS

    2014-10-01

    Full Text Available The knowledge of the feeding habits in marine species is fundamental to better understand their relationship with the environment. Although phytoplankton has been traditionally reported as the main food source consumed by the Mediterranean fan mussel Pinna nobilis, recent studies have revealed that detritus represents an important food source for this species. We analysed the degree of acceptance of muddy detritus and the utilisation of its organic matter (OM by P. nobilis on a group of 21 individuals (30.3-59.7 cm of total shell height (Ht. The specimens were collected between July and September 2012 in two areas (43°04´25” N; 5°46´7” E and 43°04´34” N; 5°47´32” E of the Embiez archipelago, northwestern Mediterranean (France. Our studies show that P. nobilis retains high quantities of OM from muddy detritus (47.50 ± 11.23% of filtered OM irrespectively of shell size. Smaller individuals, however, actively filter more detritus than large ones. The values of retained OM, together with previous studies on stomach contents, suggest that muddy detritus is a more important OM source than phytoplankton for this species.

  9. Seasonal impact of quarry mining effluent discharge impacted soils ...

    African Journals Online (AJOL)

    This study was designed to assess the impact quarry mining effluent discharge impacted soil on growth parameters and phytochemical constituents of edible vegetables. Three quarry mining sites were used for the study that covered wet and dry seasons. Plant growth such as plant height, leaf area, internodes and plant ...

  10. Ecology of rodents at an old quarry in Zambia

    African Journals Online (AJOL)

    Ecology of rodents at an old quarry in Zambia. E.N. Chidumayo. Livingstone Museum, Zambia. An old quarry, 2,5 hain size near Livingstone in southern. Zambia was kill- and live-trapped between September 1974 and December 1976 to determine ecological relations among. rodent species inhabiting it. Seven species ...

  11. Comparison of germination and seed vigor of sunflower in two contaminated soils of different texture

    Science.gov (United States)

    Zhao, Xin; Han, Jaemaro; Lee, Jong Keun; Kim, Jae Young

    2014-05-01

    Phytoremediation as an emerging low-cost and ecologically friendly alternative to the conventional soil remediation technologies has gained a great deal of attention and into lots of research. As a kind of the methods that use of green plants to remediate heavy metals contaminated soils, the early growth status of plant seeds in the contaminated environmental directly affects the effect of phytoremediation. Germination test in the water (aqueous solution of heavy metal) is generally used for assessing heavy metal phytotoxicity and possibility of plant growth, but there is a limit. Because soil is commonly main target of phytoremediation, not the water. The bioavailability of heavy metals in the soil also depends on the texture. So soil texture is an important factor of phytoremediation effect. Sunflower is the representative species which have good tolerance to various heavy metals; furthermore, the seeds of sunflower can be used as the raw-material for producing bio-diesel. The objectives of this research were to investigate germination rate of sunflowers in various heavy metal contaminated soils and to compare the seedling vigor index (SVI) of sunflower in two contaminated soils of different texture. Sunflower (Helianthusannuus L.) seeds were obtained from a commercial market. In order to prove the soil texture effect on heavy metal contaminated soil, germination tests in soil were conducted with two different types of soil texture (i.e., loam soil and sandy loam soil) classified by soil textural triangle (defined by USDA) including representative soil texture of Korea. Germination tests in soil were conducted using KS I ISO 11260-1 (2005) for reference that sunflower seeds were incubated for 7 days in dark at 25 ± 1 Celsius degree. The target heavy metals are Nickel (Ni) and Zinc (Zn). The Ni and Zn concentrations were 0, 10, 50, 100, 200, 300, 500 mg-Ni/kg-dry soil, and 0, 10, 50, 100, 300, 500, 900 mg-Zn/kg-dry soil, respectively. After germination test for 7

  12. Detritus Quality and Locality Determines Survival and Mass, but Not Export, of Wood Frogs at Metamorphosis.

    Directory of Open Access Journals (Sweden)

    Joseph R Milanovich

    Full Text Available Single-site experiments have demonstrated detritus quality in wetlands can have strongly negative, neutral, and even positive influences on wildlife. However, an examination of the influence of detritus quality across several regions is lacking and can provide information on whether impacts from variation in detritus quality are consistent across species with wide ranges. To address this gap in regional studies we examined effects of emergent and allochthonous detritus of different nutrient qualities on amphibians and assessed a mechanism that may contribute to potential impacts. We used aquatic mesocosms to raise wood frogs (Rana sylvatica from two regions of the United States with whole plants from purple loosestrife (Lythrum salicaria, leaf litter from native hardwood trees, and a mixture of both. We examined several metrics of amphibian fitness and life history, including survival, number of days to metamorphosis, and size at metamorphosis. Further, we quantified whether the effects of detritus type could translate to variation in anuran biomass or standing stock of nitrogen or phosphorus export. Our results show detritus with high nutrient quality (purple loosestrife negatively influenced survival of wood frogs, but increased size of metamorphic individuals in two different regions of the United States. Despite the decrease in survival, the increase in size of post-metamorphic anurans raised with high quality detritus resulted in anuran biomass and standing stock of N and P export being similar across treatments at both locations. These results further demonstrate the role of plant quality in shaping wetland ecosystem dynamics, and represent the first demonstration that effects are consistent within species across ecoregional boundaries.

  13. Knowledge and practice of occupational safety in quarry industries ...

    African Journals Online (AJOL)

    The findings of the study revealed that the quarry workers were semi-literate with majority having non-formal education. It was also observed that they had no knowledge of the dangers associated with quarrying and their knowledge on the use and extent of usage of protective gadgets was deficient. It was concluded that the ...

  14. Air quality assessment on human well-being in the vicinity of quarry site

    Science.gov (United States)

    Ibrahim, W. H. W.; Marinie, E.; Yunus, J.; Asra, N.; Sukor, K. Mohd

    2018-02-01

    This study aims to investigate the variation of air pollutants associated with the quarry activities prior to classified distance from quarry site. Air pollutants were monitored with the use of instruments which are Rae System Multirae Lite Pumped (PGM-6208) to measure indoor air quality while TSI 8533 Dusttrack Drx Desktop Aerosol Monitor to measure outdoor air quality. Sampling will be replicated two times. The locations of quarry are at Bandar Saujana Putra and Taman Kajang Perdana 2, Selangor. The objectives of this study are to investigate the impact of quarry mining by preparing the suitable Indoor Air Quality Index and to prepare preventive measure for residential that caused from quarry mining activities. Both Qualitative and Quantitative approaches will be implemented in this study, which employed case study and interview survey. Both quarries identified previously will be the main case study. The Respondent’s interviews are from Local Authority and Quarry Management Staff while questionnaire surveys from selected residences. Measurement method will be used to measure the Particle Matter (PM2.5) for indoor and outdoor in selected resident’s area. However, this paper is primed to discuss the method used in this study. It is not only presents the beneficial information for future research on methodologies employed but also it is anticipated the benefit to environment which can increased residents’ well-being in the vicinity of quarry sites.

  15. Quaternary sediments in Rybalsryi quarry of Dnipropetrovsk

    Directory of Open Access Journals (Sweden)

    Manyuk V.V.

    2014-12-01

    Full Text Available The results of a study of the typical section of Quaternary sediments in the Rybalske quarry and first time been reported to shift to the South boundary of the spread of the Dneprovian ice cover. Long-term observation of the geological structure subaerial and subaqueous deposits in Quaternary escarpment quarry clearly demonstrates the exceptional value, integrity, and at the same time, a certain exclusivity individual elements Quaternary section. Middle-upper Pleistocene section of substantially exceeds disclosed in Sazhovka draw, where the stratotype Kodatskiy fossil soil and elevated section of Quaternary sediments. If old Kodak can see only fragments section, an opened side by deep ravines and conditions of use cleared, the Rybalske quarry ledge submitted in one complete section alternation fossil soil horizons and loess - loess from the Dnieper to the modern black soil, and another ledge next to, well the rest of the section is exposed (from Tilihulske to Shyrokynske klimatolite. Established that among the many famous sections subaerial deposits located in the Middle Dnieper in the north-eastern part of the Dnieper-Donets basin, in the Black Sea and the Crimea and studied by the author in different years, and described loess and soil horizons (from the Black Sea to the Dnieper differ markedly lack of connectivity, flowability and friability. It is logical to assume that lithofacies conditions of the thicker subaerial deposits in the wellhead part Samara, where the Rybalske quarry markedly different from existing in these areas. Despite the obvious influence of the Dnieper glacier, direct signs which surround Dnipropetrovs’k north must be other reasons not yet explored. It is worth noting another important feature of the section of Quaternary sediments in fishing career. The above section is characteristic of the north-eastern part of the quarry, while the north, at higher marks of the watershed in the lower parts of thicker Quaternary

  16. Soil Texture and Cultivar Effects on Rice (Oryza sativa, L. Grain Yield, Yield Components and Water Productivity in Three Water Regimes.

    Directory of Open Access Journals (Sweden)

    Fugen Dou

    Full Text Available The objective of this study was to determine the effects of water regime/soil condition (continuous flooding, saturated, and aerobic, cultivar ('Cocodrie' and 'Rondo', and soil texture (clay and sandy loam on rice grain yield, yield components and water productivity using a greenhouse trial. Rice grain yield was significantly affected by soil texture and the interaction between water regime and cultivar. Significantly higher yield was obtained in continuous flooding than in aerobic and saturated soil conditions but the latter treatments were comparable to each other. For Rondo, its grain yield has decreased with soil water regimes in the order of continuous flooding, saturated and aerobic treatments. The rice grain yield in clay soil was 46% higher than in sandy loam soil averaged across cultivar and water regime. Compared to aerobic condition, saturated and continuous flooding treatments had greater panicle numbers. In addition, panicle number in clay soil was 25% higher than in sandy loam soil. The spikelet number of Cocodrie was 29% greater than that of Rondo, indicating that rice cultivar had greater effect on spikelet number than soil type and water management. Water productivity was significantly affected by the interaction of water regime and cultivar. Compared to sandy loam soil, clay soil was 25% higher in water productivity. Our results indicated that cultivar selection and soil texture are important factors in deciding what water management option to practice.

  17. DEVELOPMENT OF QUARRY SOLUTION VERSION 1.0 FOR QUICK COMPUTATION OF DRILLING AND BLASTING PARAMETERS

    OpenAIRE

    B. ADEBAYO; A. W. BELLO

    2014-01-01

    Computation of drilling cost, quantity of explosives and blasting cost are routine procedure in Quarry and all these parameters are estimated manually in most of the quarries in Nigeria. This paper deals with the development of application package QUARRY SOLUTION Version 1.0 for quarries using Visual Basic 6.0. In order to achieve this data were obtained from the quarry such as drilling and blasting activities. Also, empirical formulae developed by different researchers were used for computat...

  18. Basic model for the prediction of 137Cs concentration in the organisms of detritus food chain

    International Nuclear Information System (INIS)

    Tateda, Yuzuru

    1997-01-01

    In order to predict 137 Cs concentrations in marine organisms for monitoring, a basic model for the prediction of nuclide levels in marine organisms of detritus food chain was studied. The equilibrated values of ( 137 Cs level in organism)/( 137 Cs level in seawater) derived from calculation agreed with the observed data, indicating validity of modeling conditions. The result of simulation by this basic model showed the following conclusions. 1) ''Ecological half-life'' of 137 Cs in organisms of food chain were 35 and 130 days for detritus feeder and benthic teleosts, respectively, indicating that there was no difference of the ecological half lives in organisms between in detritus food chain and in other food chains. 2) The 137 Cs concentration in organisms showed a peak at 18 and 100 days in detritus and detritus feeder, respectively, after the introduction of 137 Cs into environmental seawater. Their concentration ratios to 137 Cs peak level in seawater were within a range of 2.7-3.8, indicating insignificant difference in the response to 137 Cs change in seawater between in the organisms of detritus food chain and of other food chain. 3) The basic model studies makes it available that the prediction of 137 Cs level in organisms of food chain can be simulated in coastal ecosystem. (author)

  19. Natural recovery of different areas of a deserted quarry in South China

    Institute of Scientific and Technical Information of China (English)

    DUAN Wenjun; REN Hai; FU Shenglei; WANG Jun; YANG Long; ZHANG Jinping

    2008-01-01

    A quarry is a surface mining operated place, which produces enormous quantities of gravel, limestone, and other materials for industrial and construction applications. Restoration and revegetation of deserted quarries are becoming increasingly important. Three areas of a typical quarry in South China: terrace for crushed materials (terrace), spoiled mound, and remaining side slope, were investigated, to compare the existing plant species and to study the relationship between environmental factors and revegetation. The plant species composition of these three areas was found to differ significantly after eight years of natural recovery. The typical plant communities found over them were composed of gramineous herbs, fems, and shrubs. Soil organic matter, soil moisture, and soil bulk density were considered to be the major determining factors for vegetation succession. There existed abiotic and biotic thresholds during quarrying restoration. Suggestions had been presented that could have accelerated the process of natural recovery in quarries.

  20. Geological-Technical and Geo-engineering Aspects of Dimensional Stone Underground Quarrying

    Science.gov (United States)

    Fornaro, Mauro; Lovera, Enrico

    Underground exploitation of dimensional stones is not a novelty, being long since practised, as proved by a number of historical documents and by a certain number of ancient quarrying voids throughout the world. Anyway, so far, open cast quarrying has been the most adopted practice for the excavation of dimensional stones. One primary reason that led to this situation is of course connected to the lower production costs of an open cast exploitation compared to an underground one. This cheapness has been supported by geological and technical motives: on the one hand, the relative availability of surface deposits and, on the other, the development of technologies, which often can be used only outdoor. But, nowadays, general costs of quarrying activities should be re-evaluated because new, and often proper, restrictions have been strongly rising during recent years. As a consequence of both environmental and technical restrictions, pressure will more and more arise to reduce open cast quarrying and to promote underground exploitations. The trend is already well marked for weak rocks - for instance in the extractive basin of Carrara, where about one hundred quarries are active, 30 per cent is working underground, but also in Spain, Portugal and Greece the number of underground marble quarries is increasing - but not yet for hard rock quarrying, where only few quarries are working underground all around the world. One reason has to be found in cutting technologies traditionally used. In weak rocks, diamond wire saw and chain cutter are usable, with few adaptations, in underground spaces, while drilling and blasting, the traditional exploitation method for hard stone, is not easily usable in a confined space, where often only one free face is available. Many technicians and researchers agree that two technologies will probably open the door to underground quarrying in hard rocks: diamond wire and water jet. The first one is already available; the second should still be

  1. Field evidence for control of quarrying by rock bridges in jointed bedrock

    Science.gov (United States)

    Hooyer, T. S.; Cohen, D. O.; Iverson, N. R.

    2011-12-01

    Quarrying is generally thought to be the most important mechanism by which glaciers erode bedrock. In quarrying models it is assumed that slow, subcritical, growth of pre-existing cracks rate-limits the process and occurs where there are large stress differences in the bed, such as near rock bumps where ice separates from the bed to form water-filled cavities. Owing to the direction of principal stresses in rocks associated with sliding and resultant cavity formation, models predict that quarrying will occur along cracks oriented perpendicular to the ice flow direction or parallel to zones of ice-bed contact. Preglacial cracks in rocks will tend to propagate mainly downward, and in sedimentary or some metamorphic rocks will merge with bedding planes, thereby helping to isolate rock blocks for dislodgement. In contrast to these model assumptions, new measurements of quarried surface orientations in the deglaciated forefield of nine glaciers in Switzerland and Canada indicate a strong correlation between orientations of pre-existing joints and quarried bedrock surfaces, independent of ice flow direction or ice-water contact lines. The strong correlation persists across all rock types, and rocks devoid of major joints lack quarried surfaces. We propose a new conceptual model of quarrying that idealizes the bedrock as a series of blocks separated by discontinuous preglacial joints containing intact rock bridges. Bridges concentrate stress differences caused by normal and shear forces acting at the rock surface. Failure of bridges is caused by slow subcritical crack growth enhanced by water pressure fluctuations. To lend credibility to this new model, we show field evidence of failed rock bridges in quarried surfaces and of rib marks on plumose structures that we interpret as arrest fracture fronts due to transient subglacial water-pressure fluctuations.

  2. 7 CFR 330.301 - Stone and quarry products from certain areas in Canada.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 5 2010-01-01 2010-01-01 false Stone and quarry products from certain areas in Canada... § 330.301 Stone and quarry products from certain areas in Canada. Stone and quarry products from areas in Canada infested with the gypsy moth may be moved from Canada into or through the United States...

  3. Influence of soil texture on hydraulic properties and water relations of a dominant warm-desert phreatophyte.

    Science.gov (United States)

    Hultine, K R; Koepke, D F; Pockman, W T; Fravolini, A; Sperry, J S; Williams, D G

    2006-03-01

    We investigated hydraulic constraints on water uptake by velvet mesquite (Prosopis velutina Woot.) at a site with sandy-loam soil and at a site with loamy-clay soil in southeastern Arizona, USA. We predicted that trees on sandy-loam soil have less negative xylem and soil water potentials during drought and a lower resistance to xylem cavitation, and reach E(crit) (the maximum steady-state transpiration rate without hydraulic failure) at higher soil water potentials than trees on loamy-clay soil. However, minimum predawn leaf xylem water potentials measured during the height of summer drought were significantly lower at the sandy-loam site (-3.5 +/- 0.1 MPa; all errors are 95% confidence limits) than at the loamy-clay site (-2.9 +/- 0.1 MPa). Minimum midday xylem water potentials also were lower at the sandy-loam site (-4.5 +/- 0.1 MPa) than at the loamy-clay site (-4.0 +/- 0.1 MPa). Despite the differences in leaf water potentials, there were no significant differences in either root or stem xylem embolism, mean cavitation pressure or Psi(95) (xylem water potential causing 95% cavitation) between trees at the two sites. A soil-plant hydraulic model parameterized with the field data predicted that E(crit) approaches zero at a substantially higher bulk soil water potential (Psi(s)) on sandy-loam soil than on loamy-clay soil, because of limiting rhizosphere conductance. The model predicted that transpiration at the sandy-loam site is limited by E(crit) and is tightly coupled to Psi(s) over much of the growing season, suggesting that seasonal transpiration fluxes at the sandy-loam site are strongly linked to intra-annual precipitation pulses. Conversely, the model predicted that trees on loamy-clay soil operate below E(crit) throughout the growing season, suggesting that fluxes on fine-textured soils are closely coupled to inter-annual changes in precipitation. Information on the combined importance of xylem and rhizosphere constraints to leaf water supply across soil

  4. Introducing a new aspect in marble quarry rehabilitation in Greece

    Science.gov (United States)

    Kaliampakos, D. C.; Mavrikos, A. A.

    2006-06-01

    For many years the marble extraction sector of the Greek mining industry has been in conflict with the public, especially in terms of rehabilitation of marble quarry sites. One of the main reasons for that is that the marble extraction sector has been unable to adjust to the existing legislative guidelines for the rehabilitation, such as extensive backfilling and re-vegetation. In the majority of cases these methods fail due to erosion of the backfill soil and adverse climatic conditions. As a result the number of abandoned marble quarry sites is continuously increasing. The present paper suggests a different approach regarding the rehabilitation of marble quarries. More specifically, the paper questions the applicability, the effectiveness, and the social usefulness of the above-mentioned guidelines and suggests the establishment of new land-uses, which are based on an in-depth analysis of the area’s special features, by taking full advantage of its potentials. What is more, the rehabilitation scheme proposes that the new land-uses and the quarrying activity may co-exist and operate simultaneously for a long period of time.

  5. Evaluation of vegetation diversity of the limestone quarry „Lafarge Ciment” (Moldova) S.A.

    OpenAIRE

    CERTAN Corina; BULIMAGA Constantin; GRABCO Nadejda

    2018-01-01

    Actual floristic research is focused on the study of the flora biodiversity and elaboration of a management plan in order to recover the flora of the „Lafarge Cement” (Moldova) S.A. quarry ecosystem. The study refers to the taxonomic investigation of the floristic diversity on adjacent to the quarry and in the proper quarry. In the frame of the study 117 species of magnoliophyta from 43 families were identified in the study area. The quarry dendroflora is represented by 20 species of arbors a...

  6. Polymer-Cement Mortar with Quarry Waste as Sand Replacement

    Directory of Open Access Journals (Sweden)

    D. N. Gómez-Balbuena

    2018-01-01

    Full Text Available The activities of carved Quarry extraction generate problems of landscape pollution such is the case of solid waste discharged into open land dumps in central Mexico. This article presents the technological application of this solid waste in a new polymeric material with properties similar to those of a traditional mortar. It is concluded that the polymeric material uses low amounts of cement with respect to the traditional mortar, and it is elaborated with the recycled quarry as they are presented in its granulometry. The polymer used favored a low water/cement ratio (0.3 which did not allow to decrease resistance due to the fine nature of the materials (residues and cement in addition to maintaining the workability of the material. The quarry residue was classified as silt with low plasticity and was characterized by X-ray diffraction and Fluorescence to identify 76% of SiO2, which is why it was used as a stone aggregate even though the fines content was approximately 93%. The maximum compression resistance obtained at 28 days were 8 Mpa with the polymer/solid ratios of 0.10, water/solids of 0.30, and quarry/solids of 0.67. Linear equations were analyzed for more representative values with R squared adjustment.

  7. Ceramic properties of clay from the Asseiceira quarry at Tomar, Portugal

    Directory of Open Access Journals (Sweden)

    Coroado, J.

    2005-09-01

    Full Text Available The clay mined at the Asseiceira quarry near the city of Tomar, Portugal, has traditionally been used to manufacture hollow brick. However, since an assessment has shown the ceramic properties of the strata to vary, the quarry could potentially produce clay blends of different qualities to form raw materials appropriate for items demanded by different market segments, such as high quality facing brick and roof or floor tiles. The composition and texture of the various clay materials identified in the Asseiceira quarry were characterized using analytical techniques such as X-ray diffraction (XRD, X-ray fluorescence (XRF, Atterberg limits and grain size analysis The phases resulting from the thermal transformations taking place during drying and firing were identified with thermogravimetric (TG, differential scanning calorimetric (DSC, and thermodilatometric (TD techniques. Finally, certain relevant ceramic properties such as linear shrinkage, bending strength and water absorption at 875 °C, 950 °C, 1025 °C and 1100 °C were determined on the raw material after extrusion.

    Las arcillas de la cantera de Asseiceira, localizadas cerca de la ciudad de Tomar (Portugal, han sido utilizadas tradicional mente en la fabricación de ladrillos. Sin embargo, el estudio de muestras procedentes de distintas capas de la cantera, ha mostrado que sus propiedades cerámicas son diferentes, lo que hace posible la formulación con diferentes grados de calidad apropiados para aprovisionar a distintos sectores del mercado de materiales cerámicos para la construcción. En este trabajo se exponen los resultados de la caracterización de los materiales arcillosos identificados en la cantera de Asseiceira mediante difracción de rayos-X (DRX, fluorescencia de rayos-X (FRX, plasticidad de Atterberg y análisis granulométrico. Las transformaciones térmicas que tienen lugar durante las etapas de secado y cocción han sido identificadas mediante an

  8. Determination of the origin and texture of marble artifacts using stable isotopes

    Science.gov (United States)

    Dotsika, E.; Poutoukis, D.; Zisi, N.; Psomiadis, D.

    2009-04-01

    For the characterization of marble and the identification of the origin of marble artifacts, samples from several ancient monuments of Greece were analyzed using several techniques: stable isotopes of carbonates (13C, 18O), XRD analysis and optical microscopy, from which information can be obtained on the origin and texture of the marble used for the production of the artifacts. The full range of grain sizes and isotopic signatures that occur in a lot of different quarries has been measured and presented. In a δ13C versus δ18O diagram, the fields corresponding to all known ancient quarries (from Penteli, Cyclades, especially Naxos (Mela, Apol, Apir, Senax), Keros, Paros (Parlak, Parlyc) and Asia Minor (Prokon)) are reported. The plots representing the analyzed samples are also shown on the same diagram. The final results of the study indicate the origin of the carbonate material of the artefacts from each of the ancient monument. In cases that the samples plot on overlapping areas, a further study is proposed, using the maximum grain size of the material.

  9. Post-closure permit application for the Kerr Hollow Quarry at the Y-12 plant

    International Nuclear Information System (INIS)

    1995-06-01

    The Kerr Hollow Quarry (KHQ) is located on U.S. Department of Energy (DOE) property at the Y-12 Plant, Oak Ridge, Tennessee. The Oak Ridge Y-12 Plant was built by the U.S. Army Corps of Engineers in 1943 as part of the Manhattan Project. Until 1992, the primary mission of the Y-12 Plant was the production and fabrication of nuclear weapons components. Activities associated with these functions included production of lithium compounds, recovery of enriched uranium from scrap material, and fabrication of uranium and other materials into finished parts for assemblies. The Kerr Hollow Quarry was used for waste disposal of a variety of materials including water-reactive and shock-sensitive chemicals and compressed gas cylinders. These materials were packaged in various containers and sank under the water in the quarry due to their great weight. Disposal activities were terminated in November, 1988 due to a determination by the Tennessee Department of Environment and Conservation that the quarry was subject to regulations under the Resource Conservation and Recovery Act of 1993. Methods of closure for the quarry were reviewed, and actions were initiated to close the quarry in accordance with closure requirements for interim status surface impoundments specified in Tennessee Rules 1200-1-11-.05(7) and 1200-1-11-.05(11). As part of these actions, efforts were made to characterize the physical and chemical nature of wastes that had been disposed of in the quarry, and to remove any containers or debris that were put into the quarry during waste disposal activities. Closure certification reports (Fraser et al. 1993 and Dames and Moore 1993) document closure activities in detail. This report contains the post-closure permit application for the Kerr Hollow Quarry site

  10. OPTIMALIZATION OF BLASTING IN »LAKOVIĆI« LIMESTONE QUARRY

    OpenAIRE

    Branko Božić; Karlo Braun

    1992-01-01

    The optimalization of exploitation in »Lakovići« limestone quarry is described. Based on determined discontinuities in the rock mass and their densities, the best possible working site have been located in order to obtain the best possible sizes of blasted rocks and work slope stability. Optimal lowest resistance line size for the quarry has been counted and proved experimentally. New blasting parameters have resulted in considerable saving of drilling and explosive (the paper is published in...

  11. DEVELOPMENT OF QUARRY SOLUTION VERSION 1.0 FOR QUICK COMPUTATION OF DRILLING AND BLASTING PARAMETERS

    Directory of Open Access Journals (Sweden)

    B. ADEBAYO

    2014-10-01

    Full Text Available Computation of drilling cost, quantity of explosives and blasting cost are routine procedure in Quarry and all these parameters are estimated manually in most of the quarries in Nigeria. This paper deals with the development of application package QUARRY SOLUTION Version 1.0 for quarries using Visual Basic 6.0. In order to achieve this data were obtained from the quarry such as drilling and blasting activities. Also, empirical formulae developed by different researchers were used for computation of the required parameters viz: practical burden, spacing, length of hole, cost of drilling consumables, drilling cost, powder factor, quantity of column charge, total quantity of explosives, volume of blast and blasting cost. The output obtained from the software QUARRY SOLUTION Version 1.0 for length of drilling, drilling cost, total quantity of explosives, volume of blast and blasting cost were compared with the results manually computed for these routine parameters estimated during drilling and blasting operation in quarry, it was then discovered that they followed the same trend. The computation from the application package revealed that 611 blast-holes require 3326.71 kg of high explosives (166 cartons of explosives and 20147.2 kg of low explosives (806 bags of explosives. The total cost was computed to be N 5133999:50 ($ 32087.49. Moreover, the output showed that these routine parameters estimated during drilling and blasting could be computed within a short time frame using this QUARRY SOLUTION, therefore, improving productivity and efficiency. This application package is recommended for use in open-pit and quarries when all necessary inputs are supplied.

  12. [Investigation of noise hazards and hearing status of workers in outdoor quarries].

    Science.gov (United States)

    Zhang, Guoying; Tang, Zhifeng; Yao, Yongping; Wang, Haiying

    2014-08-01

    To investigate the noise hazards in open quarries and to provide a basis for further control of noise hazards. An investigation was performed during 2010 to 2011 among all open quarries in Deqing County of Zhejiang Province, China. The investigation included basic information of the quarries, the occupational health situation and noise intensity at the workplace, and the hearing loss of workers exposed to noise in quarry enterprises. The hearing test results were evaluated based on the Diagnostic criteria of occupational noise-induced hearing loss (GBZ 49-2007). A total of 25 enterprises with open quarries were investigated, of which only 30.4% (17/56) workplaces met the national standard. The median noise level was 92.5 dB (A). Fifty-four (10.6%) out of 508 workers in the 25 enterprises were diagnosed with binaural hearing loss in the initial physical examination, with 18.3% (93/508) under surveillance. The rate of normal hearing among crushing workers, mechanists, drilling workers, and blasting workers ranged between 27.6% and 41.4%, which was significantly lower than that among workers exposed to slight noise hazards (80.0%) or other workers (63.7%) (P drilling workers, and blasting workers most seriously jeopardized. Among crushing workers, those working in the first-line or unprotected second?line positions suffered more than the others. Further measures should be taken by the supervision department and the enterprises to control the noise hazards in open quarries.

  13. Impact of Granite Quarrying on the Health of Workers and Nearby ...

    African Journals Online (AJOL)

    Impact of Granite Quarrying on the Health of Workers and Nearby Residents in Abeokuta Ogun State, Nigeria. ... Suspended Particulate Matter (SPM) meter was employed to monitor the level of particulate matter (PM10) within and around five quarry sites selected for this study. The data collected from hospital records of ...

  14. Effect of Partial Replacement of Sand With Quarry Dust on the ...

    African Journals Online (AJOL)

    This work investigated the effect of partial replacement of sand with quarry dust on the compressive strength, flexural strength, split tensile strength and water absorption of sandcrete blocks. River sand was replaced with quarry dust at percentages ranging from 0 to 40 at cement/combined aggregate ratio of 1: 6. The blocks ...

  15. OPTIMALIZATION OF BLASTING IN »LAKOVIĆI« LIMESTONE QUARRY

    Directory of Open Access Journals (Sweden)

    Branko Božić

    1992-12-01

    Full Text Available The optimalization of exploitation in »Lakovići« limestone quarry is described. Based on determined discontinuities in the rock mass and their densities, the best possible working site have been located in order to obtain the best possible sizes of blasted rocks and work slope stability. Optimal lowest resistance line size for the quarry has been counted and proved experimentally. New blasting parameters have resulted in considerable saving of drilling and explosive (the paper is published in Croatian.

  16. Comparison of model microbial allocation parameters in soils of varying texture

    Science.gov (United States)

    Hagerty, S. B.; Slessarev, E.; Schimel, J.

    2017-12-01

    The soil microbial community decomposes the majority of carbon (C) inputs to the soil. However, not all of this C is respired—rather, a substantial portion of the carbon processed by microbes may remain stored in the soil. The balance between C storage and respiration is controlled by microbial turnover rates and C allocation strategies. These microbial community properties may depend on soil texture, which has the potential to influence both the nature and the fate of microbial necromass and extracellular products. To evaluate the role of texture on microbial turnover and C allocation, we sampled four soils from the University of California's Hastings Reserve that varied in texture (one silt loam, two sandy loam, and on clay soil), but support similar grassland plant communities. We added 14C- glucose to the soil and measured the concentration of the label in the carbon dioxide (CO2), microbial biomass, and extractable C pools over 7 weeks. The labeled biomass turned over the slowest in the clay soil; the concentration of labeled biomass was more than 1.5 times the concentration of the other soils after 8 weeks. The clay soil also had the lowest mineralization rate of the label, and mineralization slowed after two weeks. In contrast, in the sandier soils mineralization rates were higher and did not plateau until 5 weeks into the incubation period. We fit the 14C data to a microbial allocation model and estimated microbial parameters; assimilation efficiency, exudation, and biomass specific respiration and turnover for each soil. We compare these parameters across the soil texture gradient to assess the extent to which models may need to account for variability in microbial C allocation across soils of different texture. Our results suggest that microbial C turns over more slowly in high-clay soils than in sandy soils, and that C lost from microbial biomass is retained at higher rates in high-clay soils. Accounting for these differences in microbial allocation

  17. WSSRAP [Weldon Spring Site Remedial Action Project] quarry preliminary engineering report

    International Nuclear Information System (INIS)

    1990-01-01

    The removal, transport, and temporary storage of radiologically and chemically contaminated bulk waste from the Weldon Spring Quarry will be accomplished by dividing the work into three subcontract packages. The major portion of the work will come under the bulk waste excavation package; construction of a temporary storage area (TSA) at the Weldon Spring Chemical Plant and of a haul road between the quarry and the TSA comprise the other two packages. Cost estimates to complete the removal range from $5 million to $9.4 million due to a high degree of uncertainty regarding both the productivity of the excavating equipment and the effectiveness of planned dewatering efforts. Quarry wastes will be substantially dewatered and the water treated before discharge. Waste will be excavated in three phases, using conventional construction equipment, with preliminary sorting of waste at the quarry before transport to the TSA. Special attention will be given to controlling the spread of contamination by careful monitoring and control of surface and groundwater drainage and of particulate and radiological contamination of the air. 6 refs., 21 figs., 8 tabs

  18. Use of digital image analysis combined with fractal theory to determine particle morphology and surface texture of quartz sands

    Directory of Open Access Journals (Sweden)

    Georgia S. Araujo

    2017-12-01

    Full Text Available The particle morphology and surface texture play a major role in influencing mechanical and hydraulic behaviors of sandy soils. This paper presents the use of digital image analysis combined with fractal theory as a tool to quantify the particle morphology and surface texture of two types of quartz sands widely used in the region of Vitória, Espírito Santo, southeast of Brazil. The two investigated sands are sampled from different locations. The purpose of this paper is to present a simple, straightforward, reliable and reproducible methodology that can identify representative sandy soil texture parameters. The test results of the soil samples of the two sands separated by sieving into six size fractions are presented and discussed. The main advantages of the adopted methodology are its simplicity, reliability of the results, and relatively low cost. The results show that sands from the coastal spit (BS have a greater degree of roundness and a smoother surface texture than river sands (RS. The values obtained in the test are statistically analyzed, and again it is confirmed that the BS sand has a slightly greater degree of sphericity than that of the RS sand. Moreover, the RS sand with rough surface texture has larger specific surface area values than the similar BS sand, which agree with the obtained roughness fractal dimensions. The consistent experimental results demonstrate that image analysis combined with fractal theory is an accurate and efficient method to quantify the differences in particle morphology and surface texture of quartz sands.

  19. Nutrient enrichment differentially affects body sizes of primary consumers and predators in a detritus-based stream

    Science.gov (United States)

    John M. Davis; Amy D. Rosemond; Sue L. Eggert; Wyatt F. Cross; J. Bruce. Wallace

    2010-01-01

    We assessed how a 5-yr nutrient enrichment affected the responses of different size classes of primary consumers and predators in a detritus-based headwater stream. We hypothesized that alterations in detritus availability because of enrichment would decrease the abundance and biomass of large-bodied consumers. In contrast, we found that 2 yr of enrichment increased...

  20. Quarry geotechnical report for the Weldon Spring Site Remedial Action Project, Weldon Spring, Missouri

    International Nuclear Information System (INIS)

    1990-11-01

    This report has been prepared for the United States Department of Energy's (DOE) Weldon Spring Site Remedial Action Project (WSSRAP) by the Project Management Contractor (PMC), which is MK-Ferguson Company (MK-Ferguson) with Jacobs Engineering Group (JEG) as its designated subcontractor. The Weldon Spring site (WSS) comprises the Weldon Spring quarry area and the Weldon Spring chemical plant and raffinate pit areas. This report presents the results of geotechnical investigations conducted during 1989--1990 at the proposed Weldon Spring quarry staging and water treatment facilities in the quarry area. The facilities are intended for treatment of water removed from the quarry area. An access road and a decontamination pad will be necessary for handling and transportation of bulk waste. Results of previous geotechnical investigations performed by other geoscience and environmental engineering firms in the quarry area, were reviewed, summarized and incorporated into this report. Well logging, stratigraphy data, piezometer data, elevations, and soil characteristics are also included

  1. Total exploitation of an ornamental granite quarry

    Directory of Open Access Journals (Sweden)

    Taboada, J.

    2005-09-01

    Full Text Available In this paper we propose a methodology to estimate the recovery percentage for each of the products which can be obtained from the exploitation of an ornamental granite quarry: block, semiblock, masonry-transverse stone, and the smaller materials that can be used to obtain construction aggregates. This methodology ensures that quarry exploitation is exhaustive, thereby minimising the production of spoils and the consequent negative impact on the environment. The analysis is based on a detailed and exhaustive compilation of discontinuity data from the research fronts, which are then interpreted statistically and projected over the three weakness planes that are a particular feature of ornamental granite deposits. Using this information, and bearing in mind the minimum commercially viable sizes for each kind of granite, the corresponding recovery rates are calculated for each material in each plane. The results are then integrated using spatial techniques, and the result is an evaluation of quarry contents with a view to total exploitation. This methodology was applied to a quarry in the opening phase in order to carry out an a priori assessment of the economic feasibility of the quarry.

    En este trabajo se propone una metodología para estimar el porcentaje de recuperación de cada uno de los productos que se pueden obtener en la explotación de una cantera de granito ornamental: bloque, semibloque, manpostería y per piaños, y material restante destinado a la obtención de áridos. De esta manera se logra un aprovechamiento integral de la cantera, evitándose la generación de estériles y el subsiguiente impacto ambiental producido por éstos. La metodología de análisis se basa en la recopilación detallada y exhaustiva de datos de discontinuidades en los frentes de investigación, que se interpretan estadísticamente y se proyectan sobre los tres planos de debilidad propios del granito ornamental. Con esta información, y las

  2. Water Infiltration and Hydraulic Conductivity in Sandy Cambisols

    DEFF Research Database (Denmark)

    Bens, Oliver; Wahl, Niels Arne; Fischer, Holger

    2006-01-01

    from pure Scots pine stands towards pure European beech stands. The water infiltration capacity and hydraulic conductivity (K) of the investigated sandy-textured soils are low and very few macropores exist. Additionally these pores are marked by poor connectivity and therefore do not have any...... of the experimental soils. The results indicate clearly that soils play a crucial role for water retention and therefore, in overland flow prevention. There is a need to have more awareness on the intimate link between the land use and soil properties and their possible effects on flooding.......Soil hydrological properties like infiltration capacity and hydraulic conductivity have important consequences for hydrological properties of soils in river catchments and for flood risk prevention. They are dynamic properties due to varying land use management practices. The objective...

  3. Geomorphological records of diachronous quarrying activities along the ancient Appia route at the Aurunci Mountain pass (Central Italy)

    Science.gov (United States)

    Di Luzio, E.; Carfora, P.

    2018-04-01

    The topic of this research consists in the description of landscape modifications occurring from the 4th century BCE to the 19th century CE as a consequence of quarrying activities on carbonate slopes along a tract of the ancient Appia route crossing the central Apennine belt at the Aurunci Mountain pass (Lazio region, central Italy). The main objectives were to discern different quarrying phases and techniques, quantify quarrying activities and understand the role of quarrying in create morphological features. Multidisciplinary studies were completed including aerial photogrammetry, geoarchaeological field surveys, morphometric characterization of quarry areas, structural analysis of rock outcrops aided by terrestrial photogrammetry, GPS measurements. The results of this study show how the local geomorpological and tectonic setting determined which kinds of extractable rock material, i.e., rock blocks or breccias, were used for different purposes. Moreover, different phases of extraction were evidenced. A main Roman quarrying phase, lasting between the 4th century BCE and the 1st century CE, was recognized as taking place over eight quarry areas. These are delimited by sharp edges and have regular shapes, revealing in some cases a staircase-like morphological profile, and are characterized by similar volumes of extracted rock material. A later quarrying phase -the Bourbon Age, 19th century CE-is assumed to be evidenced instead by five quarries with a peculiar semi-elliptical shape and different volumes of carved material. Seven quarries were found to be of uncertain age. The quarry system described in this paper, together with geomorphological records of slope cuts, terraced surfaces, and the remains of retaining walls, represents a unique and important example of anthropogenic landscape modification in the territory of the central Apennines caused by the construction and maintenance of a Roman road over the centuries. This could be relevant for further studies on

  4. Landscape evolution by subglacial quarrying

    DEFF Research Database (Denmark)

    Ugelvig, Sofie Vej; Egholm, D.L.; Iverson, Neal R.

    In glacial landscape evolution models, subglacial erosion rates are often related to basal sliding or ice discharge by a power-law. This relation can be justified for bedrock abrasion because rock debris transported in the basal ice drives the erosion. However, a simple relation between rates of ...... evolution models. Geology, v. 40, no. 8, 679-682 (2012). Schoof, C. The effect of cavitation on glacier sliding. Proc. R. Soc. A , 461, 609-627 (2005). Jaeger, J.C., and Cook, N.G.W. Fundamentals of rock mechanics: New York, Chapman and Hall, 593 p. (1979)......In glacial landscape evolution models, subglacial erosion rates are often related to basal sliding or ice discharge by a power-law. This relation can be justified for bedrock abrasion because rock debris transported in the basal ice drives the erosion. However, a simple relation between rates...... of sliding and erosion is not well supported when considering models for quarrying of rock blocks from the bed. Iverson (2012) introduced a new subglacial quarrying model that operates from the theory of adhesive wear. The model is based on the fact that cavities, with a high level of bedrock differential...

  5. Feasibility study for management of the bulk wastes at the Weldon Spring quarry, Weldon Spring, Missouri

    International Nuclear Information System (INIS)

    1990-02-01

    The US Department of Energy (DOE), under its Surplus Facilities Management Program, is responsible for conducting remedial actions at the Weldon Spring site in St. Charles County, Missouri. The Weldon Spring site, which is listed on the National Priorities List of the US Environmental Protection Agency (EPA), became contaminated as a result of processing and disposal activities that took place from the 1940s through the 1960s. The site consists of a quarry and a chemical plant area located about 6.4 km (4 mi) northeast of the quarry. The quarry is surrounded by the Weldon Spring Wildlife Area and is near a well field that constitutes a major source of potable water for St. Charles County; the nearest supply well is located about 0.8 km (0.5 mi) southeast of the quarry. From 1942 to 1969, the quarry was used for the disposal of various radioactively and chemically contaminated materials. Bulk wastes in the quarry consist of contaminated soils and sediments, rubble, metal debris, and equipment. As part of overall site remediation, DOE is proposing to conduct an interim remedial action at the quarry to manage the radioactively and chemically contaminated bulk waste contained therein. 105 refs., 33 figs., 42 tabs

  6. Determination of risk indices in quarries of two basins in La Plata Municipality Argentina

    International Nuclear Information System (INIS)

    Cabral, M.; Crincoli, A.; Gimenez, J.; Hurtado, M.

    2004-01-01

    Soil extraction is one of the main causes of degradation of this resource in Buenos Aires province. In La Plata municipality, soil is extracted at different depths for a variety of uses. Deep soil extraction creates quarries which have a negative impact on the environment, the landscape, the real estate value and life quality. The inundated quarries become precarious swimming places where many people have drowned. When the quarries are used as garbage dumps, they can concentrate disease vectors or pollute groundwater through their leachates. The face-cuts are often near vertical and can be susceptible to collapse. The methodology to calculate the risk index is based on the hypothesis that risk variables can be identified, individually assessed and combined in such a way that they would provide a numerical value reflecting the likelihood of accidents or diseases occurring as a consequence of quarry's presence. The general objective of the project is to obtain an index for the quarries of the studied basins aimed at warning local authorities and affected persons about the sites where protection and reclamation measures are more urgently needed. The values obtained are represented on a map showing the risk class of each quarry. It is concluded that the methodology is useful to determine priorities and can prove a good management tool for those involved in this problem [es

  7. Decomposition dynamic of two aquatic macrophytes Trapa bispinosa Roxb. and Nelumbo nucifera detritus.

    Science.gov (United States)

    Zhou, Xiaohong; Feng, Deyou; Wen, Chunzi; Liu, Dan

    2018-03-29

    In freshwater ecosystems, aquatic macrophytes play significant roles in nutrient cycling. One problem in this process is nutrient loss in the tissues of untimely harvested plants. In this study, we used two aquatic species, Nelumbo nucifera and Trapa bispinosa Roxb., to investigate the decomposition dynamics and nutrient release from detritus. Litter bags containing 10 g of stems (plus petioles) and leaves for each species detritus were incubated in the pond from November 2016 to May 2017. Nine times litterbags were retrieved on days 6, 14, 25, 45, 65, 90, 125, 145, and 165 after the decomposition experiment for the monitoring of biomass loss and nutrient release. The results suggested that the dry masses of N. nucifera and T. bispinosa decomposed by 49.35-69.40 and 82.65-91.65%, respectively. The order of decomposition rate constants (k) is as follows: leaves of T. bispinosa (0.0122 day -1 ) > stems (plus petioles) of T. bispinosa (0.0090 day -1 ) > leaves of N. nucifera (0.0060 day -1 ) > stems (plus petioles) of N. nucifera (0.0030 day -1 ). Additionally, the orders of time for 50% dry mass decay, time for 95% dry mass decay, and turnover rate are as follows: leaves  0.05). In addition, the decomposition time had also significant effects on the detritus decomposition dynamic and nutrient release. However, the contributors of species and decomposition time on detritus decomposition were significantly different on the basis of their F values of two-way ANOVA results. This study can provide scientific bases for the aquatic plant scientific management in freshwater ecosystems of the East region of China.

  8. Suitability of iron ore tailings and quarry dust as fine aggregates for ...

    African Journals Online (AJOL)

    Eight concrete mixes were produced with different levels of sand replacement by either iron ore tailings or quarry dust, while the ninth mix of 100 % river sand served as the control. The highest 28-day compressive strength of 29.2 N/mm2 was obtained by blending 75 % sand and 25 % quarry dust with cement, which was 7 ...

  9. The 16 most common fossil groups from Danian found in Faxe Quarry

    DEFF Research Database (Denmark)

    Lauridsen, Bodil Wesenberg

    2009-01-01

    Twelve folders dealing with the 16 most common fossil groups from Danian found in Faxe Quarry. The folders are for sale at the museum and designated for visitor......Twelve folders dealing with the 16 most common fossil groups from Danian found in Faxe Quarry. The folders are for sale at the museum and designated for visitor...

  10. Thraustochytrid and fungal component of marine detritus. 1. Field studies on decomposition of the brown alga Sargassum cinereum J. Ag.

    Digital Repository Service at National Institute of Oceanography (India)

    Sathe-Pathak, V.; Raghukumar, S.; Raghukumar, C.; Sharma, S.

    Thraustochytrid protists and fungi were isolated and enumerated in culture from detritus of the brown alga Sargassum cinereum. Both groups occurred epi- and endobiontically in the detritus. The thraustochytrid Labyrinthuloides minuta occurred...

  11. Using a noise monitoring station in a small quarry located in an urban area.

    Science.gov (United States)

    Wichers, Michiel; Iramina, Wilson Siguemasa; de Eston, Sérgio Médici; Ayres da Silva, Anna Luiza Marques

    2017-12-22

    Mining plays an important role in Brazilian exports. On the other hand, large urban centers like São Paulo, with approximately 21 million inhabitants, also demand an increasing domestic consumption of natural resources, such as construction aggregate. There are many quarries located in the surroundings of urban centers in Brazil, competing with the growth of urbanized areas. Such proximity leads to a series of conflicts involving quarries and surrounding communities, where the increase in noise levels is highlighted. Operations in quarries, in general, are intermittent. Noisier equipment, such as drilling rigs and primary crushers, operates only a few hours during the day, while other operations, such as screening and secondary and tertiary crushing, are more constant. This paper presents a study carried out in a quarry located near São Paulo, where in addition to conventional short term noise measurements at surrounding receptors, one noise monitoring station was installed, allowing to identify the noisiest moments during the quarry operating time. Through data transmitted by wireless technology, it was possible to follow the noise variations emitted from mining activities in real time and observe the noisiest events that were recorded for events that exceeded the established standards. A mobile application associated to this monitoring station facilitated the quarry's manager and employees to access immediately the monitoring information. Therefore, by using this system, it was possible to evaluate the effectiveness of noise reduction measures already taken and indicate what steps still need to be held.

  12. HISTORY AND TOURIST VALORIZATION OF THE RUSCHIȚA MARBLE QUARRY (CARAȘ-SEVERIN COUNTY, ROMANIA

    Directory of Open Access Journals (Sweden)

    D.-R. TODOR

    2015-10-01

    Full Text Available History and Tourist Valorization of the Ruschița Marble Quarry (Caraș-Severin County, Romania. With an area of over 40 ha, the marble quarry located north of Ruschița village, Rusca Montană commune, Caraș-Severin County is the largest exploitation perimeter of this kind on the territory of Romania and one of the largest in Europe. Many works were written about the Ruschița marble quarry across time, especially regarding geology, but very little was talked about its tourism potential. If generally, the vast majority of the extractive areas are not at all attractive from the tourist point of view, having rather a repulsive appearance, the marble quarry from Ruschița proves the contrary, both by the greatness and sizes of exploitation and by the surrounding area, constituted of a very diversified mountain relief and an abundant forest vegetation. That is why, we consider useful an attraction and integration in the tourist circuit of this spectacular anthropogenic monument, unique in Romania, comparable to the Carrara (Italy marble quarries. This paper makes a pleading in this respect.

  13. Characterization and assessment for the Weldon Spring Quarry low-level radioactive waste storage site

    International Nuclear Information System (INIS)

    1984-09-01

    The Weldon Spring Quarry is located approximately 4 miles from the Weldon Spring Chemical Plant and 20 miles west of St. Louis. Originally a limestone and sand quarry, the 9 acre site was later used for the disposal of TNT-contaminated soils during the 1940's and the disposal of low-level radioactive waste during the 1960's. The most important potential hazards posed by the quarry are contamination of groundwater, radiation exposure and contamination of trespassers, and contamination of surface waters. The potential for groundwater contamination was identified at an early date by the US Department of Energy (DOE) as the most important of these potential hazards. Particular concern exists for the future of the municipal well field located between the quarry and the Missouri River. At the present time the well field supplies drinking water for the area from Weldon Spring up to and including parts of the city of St. Charles. Chapters are devoted to geology, waste inventory, hydrology, investigations of radionuclide migration from the quarry, numerical modeling of engineering options, and raffinate pits. 40 references, 182 figures, 49 tables, 7 appendixes

  14. Changes in N cycling induced by Ulva detritus enrichment of sediments

    DEFF Research Database (Denmark)

    Garcia-Robledo, Emilio; Revsbech, Niels Peter; Risgaard-Petersen, Nils

    2013-01-01

    Macroalgal accumulation and decomposition in shallow water environments typically result in an increase in the organic matter content of the sediment, affecting both benthic metabolism and nutrient dynamics. The present study investigates how a pulse addition of Ulva detritus to estuarine sedimen...

  15. Carbon and oxygen isotopic ratio bi-variate distribution for marble artifacts quarry assignment

    International Nuclear Information System (INIS)

    Pentia, M.

    1995-01-01

    Statistical description, by a Gaussian bi-variate probability distribution of 13 C/ 12 C and 18 O/ 16 O isotopic ratios in the ancient marble quarries has been done and the new method for obtaining the confidence level quarry assignment for marble artifacts has been presented. (author) 8 figs., 3 tabs., 4 refs

  16. Soil texture and depth influence on the neutron probe calibration

    International Nuclear Information System (INIS)

    Santos, Reginaldo Ferreira; Carlesso, Reimar

    1998-01-01

    The neutron probe is an equipment used on determination of the soil water content, based on the fast neutron attenuation. Therefore, there is a calibration need in the field and, consequently, to verify the soil texture and depth influence for to determining the calibration curves in relation to the water content. The study was developed at Santa Maria's Federal University in a lisimeter group, protected from the rains with transparent plastic. There different soil textures, three depths (10, 30 and 50 cm from the soil surface) and four replicates were used. Linear regression equations between neutron counts and soil water contents were made. The results showed that there was interference of the texture and depth of the soil, analyzed jointly, on the calibration curves, and the observed and estimated values varied form o,02 to 0,06 cm3/cm3 of the soil water content and the correlation coefficients were 0,86 0,95 and 0,89 for clayray, franc-silt-clayey and franc-sandy, respectively. For soil texture and depth, analyzed separately, the differences among the values observed in the field and the estimated ones, varied from 0,0 to 0,02 cm3/cm3 soil water content and presented correlation coefficients between 0,97 and 1,0. (author)

  17. Comparison of physical and mechanical properties of river sand concrete with quarry dust concrete

    Science.gov (United States)

    Opara, Hyginus E.; Eziefula, Uchechi G.; Eziefula, Bennett I.

    2018-03-01

    This study compared the physical and mechanical properties of river sand concrete with quarry dust concrete. The constituent materials were batched by weight. The water-cement ratio and mix ratio selected for the experimental investigation were 0.55 and 1:2:4, respectively. The specimens were cured for 7, 14, 21 and 28 days. Slump, density and compressive strength tests were carried out. The results showed that river sand concrete had greater density and compressive strength than quarry dust concrete for all curing ages. At 28 days of curing, river sand concrete exceeded the target compressive strength by 36%, whereas quarry dust concrete was less than the target compressive strength by 12%. Both river sand concrete and quarry dust concrete for the selected water/cement ratio and mix ratio are suitable for non-structural applications and lightly-loaded members where high strength is not a prerequisite.

  18. Occupational health hazards among quarry employees in Ebonyi ...

    African Journals Online (AJOL)

    Occupational health hazards among quarry employees in Ebonyi state, ... how these problems affect the conditions of employees in such industries in Ebonyi State. ... the level of compliance of safety and protective devices among employees.

  19. The impact of pumped water from a de-watered Magnesian limestone quarry on an adjacent wetland: Thrislington, County Durham, UK

    International Nuclear Information System (INIS)

    Mayes, W.M.; Large, A.R.G.; Younger, P.L.

    2005-01-01

    Although quarrying is often cited as a potential threat to wetland systems, there is a lack of relevant, quantitative case studies in the literature. The impact of pumped groundwater discharged from a quarry into a wetland area was assessed relative to reference conditions in an adjacent fen wetland that receives only natural runoff. Analysis of vegetation patterns at the quarry wetland site, using Detrended Correspondence Analysis and the species indicator values of Ellenberg, revealed a clear disparity between community transitions in the quarry wetland and the reference site. Limited establishment of moisture-sensitive taxa, the preferential proliferation of robust wetland species and an overall shift towards lower species diversity in the quarry wetland were explicable primarily by the physico-chemical environment created by quarry dewatering. This encompassed high pH (up to 12.8), sediment-rich effluent creating a nutrient-poor substrate with poor moisture retention in the quarry wetland, and large fluctuations in water levels. - High pH, sediment-rich runoff from a quarry constrains floristic diversity in an adjacent wetland

  20. The impact of pumped water from a de-watered Magnesian limestone quarry on an adjacent wetland: Thrislington, County Durham, UK

    Energy Technology Data Exchange (ETDEWEB)

    Mayes, W.M. [Institute for Research on Environment and Sustainability, University of Newcastle, Newcastle upon Tyne NE1 7RU (United Kingdom)]. E-mail: w.m.mayes@ncl.ac.uk; Large, A.R.G. [School of Geography, Politics and Sociology, University of Newcastle, Newcastle upon Tyne NE1 7RU (United Kingdom); Younger, P.L. [Institute for Research on Environment and Sustainability, University of Newcastle, Newcastle upon Tyne NE1 7RU (United Kingdom)

    2005-12-15

    Although quarrying is often cited as a potential threat to wetland systems, there is a lack of relevant, quantitative case studies in the literature. The impact of pumped groundwater discharged from a quarry into a wetland area was assessed relative to reference conditions in an adjacent fen wetland that receives only natural runoff. Analysis of vegetation patterns at the quarry wetland site, using Detrended Correspondence Analysis and the species indicator values of Ellenberg, revealed a clear disparity between community transitions in the quarry wetland and the reference site. Limited establishment of moisture-sensitive taxa, the preferential proliferation of robust wetland species and an overall shift towards lower species diversity in the quarry wetland were explicable primarily by the physico-chemical environment created by quarry dewatering. This encompassed high pH (up to 12.8), sediment-rich effluent creating a nutrient-poor substrate with poor moisture retention in the quarry wetland, and large fluctuations in water levels. - High pH, sediment-rich runoff from a quarry constrains floristic diversity in an adjacent wetland.

  1. Prograding coastal facies associations in the Vryheid formation (Permian) at Effingham quarries near Durban, South Africa

    Science.gov (United States)

    Tavener-Smith, R.

    1982-05-01

    This paper describes and interprets a flat-lying, sandstone—siltstone sequence 70 m thick in three disused quarries. The beds comprise the lowest part of the Vryheid Formation (middle Ecca) in the Durban vicinity. The sequence is conveniently divisible into two parts: the Lower Division constitutes a prograding beach barrier association, while the upper one represents a back barrier lagoonal complex. Fourteen sedimentary facies are described and interpreted to represent a range of depositional environments including open water shelf silts, sandy shoreface and littoral deposits, organic-rich muds and peats of lagoonal origin, a tidal inlet, washover fans and a fluvial channel sand. Among the conclusions reached are that the local middle Ecca coastline extended in a northwest to southeast direction and that progradation was towards the southwest; that the coastline was microtidal and that stormy conditions were common with prevalent palaeowinds from the northwest. The absence of invertebrate body fossils in these strata is attributed to penecontemporaneous solution of shelly remains. This is the first time that a coastal sequence has been identified on the southeast margin of the Main Karoo Basin of South Africa

  2. Microseisms from Superstorm Sandy

    Science.gov (United States)

    Sufri, Oner; Koper, Keith D.; Burlacu, Relu; de Foy, Benjamin

    2014-09-01

    We analyzed and visualized the microseisms generated by Superstorm Sandy as recorded by the Earthscope Transportable Array (TA) during late October through early November of 2012. We applied continuous, frequency-dependent polarization analysis to the data and were able to track the course of Sandy as it approached the Florida coastline and, later, the northeastern coast of the U.S. The energy level of Sandy was roughly comparable to the background microseism level generated by wave-wave interactions in the North Atlantic and North Pacific oceans. The maximum microseismic power and degree of polarization were observed across the TA when Sandy sharply changed its direction to the west-northwest (specifically, towards Long Island, New York) on October 29. The westward turn also briefly changed the dominant microseism period from 5 s to 8 s. We identified three other microseismic source regions during the 18 day observation period. In particular, peak-splitting in the double frequency band and the orientation of the 5 s and 8 s polarization vectors revealed two contemporaneous microseism sources, one in the North Atlantic and one in the Northeast Pacific, for the dates of November 3-4. Predictions of microseismic excitation based on ocean wave models showed consistency with the observed microseismic energy generated by Sandy and other storms.

  3. Application of restoration ecology principles to the practice of limestone quarry rehabilitation in Lebanon

    International Nuclear Information System (INIS)

    Khater, C.; Arnaud, M.

    2007-01-01

    Restoration ecology is an emerging science dealing with applied ecology and aiming at ''helping nature to recreate itself''. This comprehensive paper presents the findings and main results related to the analysis of natural vegetation dynamics on abandoned limestone quarries in Mediterranean environment. It aims to answer three basic questions: where, when and how should intervention by ecological restoration be achieved in abandoned limestone quarries. Results show that quarries are heterogeneous ecosystems and interventional strategies should be planned according to the different landforms observed. Quarry faces potentially host a particular saxicolous flora often composed of rare and endemic species, intervention is not recommended, unless required by urban planning issues. Intervention on platforms can be very expensive (substratum fracturing) and involves heavy engineering works. Restoration on quarry embankments aims at orienting and accelerating natural regeneration processes in order to shortcut the first stages naturally dominated by annuals and ruderal species. 27 species suitable for revegetation purposes have been identified for the different bioclimatic levels in Lebanon. They respond to two major criteria: availability in the natural surroundings (indigenous species) and adaptability to local conditions (pioneer adapted species). In conclusion, this paper suggests future openings for a development field integrating economical opportunities on solid scientific bases. (author)

  4. Precise age and biostratigraphic significance of the Kinney Brick Quarry Lagerstätte, Pennsylvanian of New Mexico, USA

    DEFF Research Database (Denmark)

    Lucas, Spencer G.; Allen, Bruce D.; Krainer, Karl

    2011-01-01

    The Kinney Brick Quarry is a world famous Late Pennsylvanian fossil Lagerstätte in central New Mexico, USA. The age assigned to the Kinney Brick Quarry (early-middle Virgilian) has long been based more on its inferred lithostratigraphic position than on biostratigraphic indicators at the quarry. We...

  5. Identification, preliminary study and valorization of the historical quarries of San Ciprián (Lugo)

    International Nuclear Information System (INIS)

    Fernández Suárez, J.; Álvarez Areces, E.; Baltuille Martín, J.M.; Martínez-Martínez, J.

    2017-01-01

    The aim of this paper is showing the existence and characteristics of the historical quarries where the building stones were extracted for the construction of the Architectural Heritage of San Ciprián. It is a small town in the north of Lugo (Galicia, NW of Spain) with a long tradition in the use of the natural stone as building material in its architectural heritage. In addition to the benefits in the historical, socio-economic and industrial knowledge, the location of historical quarries is a fundamental task for the conservation plans, allowing to define the original state of the building stone. Moreover, they provide a new contribution to the regional tourist development, including their location and description in the cultural and environmental touristic routes. This study reveals the existence and characteristics of the signs of operation located in the historical quarries associated with the Architectural Heritage of San Ciprián, although in some cases this quarries have disappeared partially or totally. The areas located are: Porto de Riba, Figueiras, Area of the estuary and Lieiro quarry; we can not affirm the existence of other areas under new constructions, especially in the Porto de Riba and Figueiras. [es

  6. COPROLITES FROM THE DANIAN LIMESTONE (LOWER PALEOCENE) OF FAXE QUARRY, DENMARK

    DEFF Research Database (Denmark)

    Milàn, Jesper

    2010-01-01

    are attributed to sharks, and large, cylindrical coprolites with longitudinal striations on the surface are identified as crocodile coprolites. Fish and sharks are known from abundant finds of otoliths and teeth in Faxe Quarry, and crocodiles are known from finds of single bones and teeth.......A collection of coprolites found in the Danian (Lower Paleocene) limestone of Faxe Quarry, Denmark, is described and attributed to the respective producers. Small, drop-like specimens with weak signs of spiral coiling are attributed to fish. Larger, heteropolar, spirally-coiled specimens...

  7. Mineralogical characterization of quarry fines from Tracuateua city, state of Para, Brazil

    International Nuclear Information System (INIS)

    Costa, J.H.B. da; Negrao, R.C.; Angelica, R.S.; Universidade Federal do Para

    2011-01-01

    The aim of this study was to characterize the mineralogy quarry fines samples for its reuse and thus contributing to mitigate the environmental impact caused by this waste. In order to achieve the results, samples were collected and prepared for assays and identification of the mineralogical phases present in the quarry fines from the samples. X-ray diffraction and optical microscopy techniques were used. The quarry of fines characterization was based on qualitatively identification the minerals present in the samples. It was detected the presence of quartz, muscovite and feldspar (albite and microclinite) by x-ray diffraction technique and microscopic and macroscopic observations. Moreover, the size distribution was determined, and the samples presented a medium to fine size (ranging from 9,5 mm to 0,075 mm) and the grains presented an irregular and angular shapes. (author)

  8. The Energy-Efficient Quarry: Towards improved understanding and optimisation of energy use and minimisation of CO2 generation in the aggregates industry.

    Science.gov (United States)

    Hill, Ian; White, Toby; Owen, Sarah

    2014-05-01

    Extraction and processing of rock materials to produce aggregates is carried out at some 20,000 quarries across the EU. All stages of the processing and transport of hard and dense materials inevitably consume high levels of energy and have consequent significant carbon footprints. The FP7 project "the Energy Efficient Quarry" (EE-Quarry) has been addressing this problem and has devised strategies, supported by modelling software, to assist the quarrying industry to assess and optimise its energy use, and to minimise its carbon footprint. Aggregate quarries across Europe vary enormously in the scale of the quarrying operations, the nature of the worked mineral, and the processing to produce a final market product. Nevertheless most quarries involve most or all of a series of essential stages; deposit assessment, drilling and blasting, loading and hauling, and crushing and screening. The process of determining the energy-efficiency of each stage is complex, but is broadly understood in principle and there are numerous sources of information and guidance available in the literature and on-line. More complex still is the interaction between each of these stages. For example, using a little more energy in blasting to increase fragmentation may save much greater energy in later crushing and screening, but also generate more fines material which is discarded as waste and the embedded energy in this material is lost. Thus the calculation of the embedded energy in the waste material becomes an input to the determination of the blasting strategy. Such feedback loops abound in the overall quarry optimisation. The project has involved research and demonstration operations at a number of quarries distributed across Europe carried out by all partners in the EE-Quarry project, working in collaboration with many of the major quarrying companies operating in the EU. The EE-Quarry project is developing a sophisticated modelling tool, the "EE-Quarry Model" available to the quarrying

  9. Analysis of noise pollution in an andesite quarry with the use of simulation studies and evaluation indices.

    Science.gov (United States)

    Kosała, Krzysztof; Stępień, Bartłomiej

    2016-01-01

    This paper presents the verification of two partial indices proposed for the evaluation of continuous and impulse noise pollution in quarries. These indices, together with the sound power of machines index and the noise hazard index at the workstation, are components of the global index of assessment of noise hazard in the working environment of a quarry. This paper shows the results of acoustic tests carried out in an andesite quarry. Noise generated by machines and from performed blasting works was investigated. On the basis of acoustic measurements carried out in real conditions, the sound power levels of machines and the phenomenon of explosion were determined and, based on the results, three-dimensional models of acoustic noise propagation in the quarry were developed. To assess the degree of noise pollution in the area of the quarry, the continuous and impulse noise indices were used.

  10. Light Gray Surface-Gleyed Loamy Sandy Soils of the Northern Part of Tambov Plain: Agroecology, Properties, and Diagnostics

    Science.gov (United States)

    Zaidel'man, F. R.; Stepantsova, L. V.; Nikiforova, A. S.; Krasin, V. N.; Dautokov, I. M.; Krasina, T. V.

    2018-04-01

    Light gray soils of Tambov oblast mainly develop from sandy and loamy sandy parent materials; these are the least studied soils in this region. Despite their coarse texture, these soils are subjected to surface waterlogging. They are stronger affected by the agrogenic degradation in comparison with chernozems and dark gray soils. Morphology, major elements of water regime, physical properties, and productivity of loamy sandy light gray soils with different degrees of gleyzation have been studied in the northern part of Tambov Plain in order to substantiate the appropriate methods of their management. The texture of these soils changes at the depth of 70-100 cm. The upper part is enriched in silt particles (16-30%); in the lower part, the sand content reaches 80-85%. In the nongleyed variants, middle-profile horizons contain thin iron-cemented lamellae (pseudofibers); in surface-gleyed variants, iron nodules are present in the humus horizon. The removal of clay from the humus horizon and its accumulation at the lithological contact and in pseudofibers promote surface subsidence and formation of microlows in the years with moderate and intense winter precipitation. The low range of active moisture favors desiccation of the upper horizons to the wilting point in dry years. The yield of cereal crops reaches 3.5-4.5 t/ha in the years with high and moderate summer precipitation on nongleyed and slightly gleyed light gray soils and decreases by 20-50% on strongly gleyed light gray soils. On light gray soils without irrigation, crop yields are unstable, and productivity of pastures is low. High yields of cereals and vegetables can be obtained on irrigated soils. In this case, local drainage measures should be applied to microlows; liming can be recommended to improve soil productivity.

  11. Ecological risk assessment: influence of texture on background concentration of microelements in soils of Russia.

    Science.gov (United States)

    Beketskaya, Olga

    2010-05-01

    , organic matter content, concentration of microelements and pH value. On the basis of this data base massive of data for Forest-steppe and Steppe regions was create, which was divided by texture. For all data statistics method was done and was calculated maximum level natural microelements content for soils with different texture (?+3*δ). As a result of our statistic calculation we got middle and the top limit of background concentration of microelements in sandy and clay soils (conditional border - sandy loam) of two regions. We showed, that for all territory of European part of Russia and for Forest-steppe and Steppe regions separately middle content and maximum level natural microelements concentrations (?+3*σ) are higher in clay soils, rather then in sandy soils. Data characterizing soils, in different regions, of similar texture differs less than the data collected for sandy and clay soils of the same region. After all this calculation we can notice, that data of middle and top limit of background microelements concentration in soils, based on statistic method, can be used in the aim of ecological risk assessment. Using offered method allow to calculate top limit of background concentration for sandy and clay soils for large-scale geographic regions, exceeding which will be evidence of anthropogenic contamination of soil.

  12. THE FLOW ANALYSIS ABOUT TRACTION OF QUARRY TRAINS

    Directory of Open Access Journals (Sweden)

    G. K. Getman

    2010-04-01

    Full Text Available The method of determination of constituents of expense of electric power on traction of quarry trains is resulted in the article, and also the degree of their intercommunication with the mode of train motion is analysed.

  13. Noise Exposure and Hearing Capabilities of Quarry Workers in Ghana: A Cross-Sectional Study.

    Science.gov (United States)

    Gyamfi, Charles Kwame R; Amankwaa, Isaac; Owusu Sekyere, Frank; Boateng, Daniel

    2016-01-01

    Although quarry operations have high economic significance, the effects they cause to the workers in terms of excessive noise production cannot be overlooked. This cross-sectional study assessed the extent of noise exposure and its influence on hearing capabilities among quarry workers in Ashanti region. The study involved 400 workers randomly selected from five quarries in Ashanti region from April to June 2012. Data was collected using structured questionnaires, physical examination, and audiological assessments. A logistic regression model was fitted to assess independent predictors of hearing loss. All the machines used at the various quarries produced noise that exceeded the minimum threshold with levels ranging from 85.5 dBA to 102.7 dBA. 176 (44%) of study respondents had hearing threshold higher than 25 dBA. 18% and 2% of these were moderately (41-55 dBA) and severely (71-90 dBA) impaired, respectively. Age, duration of work, and use of earplugs independently predicted the development of hearing loss. Use of earplugs showed a protective effect on the development of hearing loss (OR = 0.45; 95% CI = 0.25, 0.84). This study provides empirical evidence on the extent of damage caused to quarry workers as a result of excessive noise exposure. This will support the institution of appropriate protective measures to minimize this threat.

  14. Characteristics of the quarry as shielding for "2"4"1AmBe neutrons and monoenergetic photons

    International Nuclear Information System (INIS)

    Vega C, H. R.; Hernandez D, V. M.; Letechipia de L, C.; Salas L, M. A.; Rodriguez R, J. A.; Juarez A, C. A.

    2016-09-01

    Shielding is an important element in radiation protection since allows the management of radiation sources. Currently there are different materials of natural or anthropogenic origin that are used as shielding for both photons and neutrons. The quarry is a material of natural origin and abundant in our country, which is used in construction or for the manufacture of sculptures, however its characteristics as shielding have not been reported. In this paper we report some of the properties of the quarry as shielding for monoenergetic photons and for neutrons produced by an isotopic neutron source of "2"4"1AmBe. A quarry piece was used to determine its density and its chemical composition, with the XCOM code the elemental composition was determined and the mass interaction and total attenuation coefficients of the quarry were determined with photons of 10"-"3 to 10"-"5 MeV; the interaction coefficients included coherent dispersion, photoelectric absorption, Compton dispersion and the production of pairs in the nuclear and electronic field. Using the MCNP5 code, a narrow geometry attenuation experiment was modeled and the photon fluence was estimated that reaches a point detector at a distance of 42 cm from a point source, isotropic and monoenergetic photon when the source and the point detector were added quarry pieces of different thicknesses. The reduction of the number of photons as a function of the thickness of the quarry was used to determine the coefficient of linear attenuation of the quarry before photons of 0.03, 0.07, 0.1, 0.3, 1, 2 and 3 MeV that were the same as those calculated with the XCOM code. With the MCNP, the K a and H(10) transmission curves were also calculated. This same model was used to determined the variation of the "2"4"1AmBe neutron spectrum as a function of quarry thickness, as well as the E_R_O_T and H(10) transmission curves. (Author)

  15. Novel pixel sensors will be key to capturing quarry

    CERN Multimedia

    Weiss, Giselle

    2007-01-01

    Scientists at CERN: their main quarry will be a tantalizing subatomic particle called the Higgs boson, considered pivotal to our understanding of mass and predicted by the so-called Standard Model. (2 pages)

  16. Engineering evaluation/cost analysis for the proposed management of contaminated water in the Weldon Spring quarry

    International Nuclear Information System (INIS)

    MacDonell, M.M.; Peterson, J.M.; Joya, I.E.

    1989-01-01

    This engineering evaluation/cost analysis (EE/CA) report has been prepared to support the proposed removal action for management of contaminated water in the Weldon Spring quarry, located near Weldon Spring, Missouri. The water became chemically and radioactively contaminated as a result of contact with various wastes that were disposed of in the quarry between 1942 and 1968. The US Department of Energy is responsible for cleanup activities at the Weldon Spring site, which includes the quarry, under its Surplus Facilities Management Program (SFMP). The major goals of SFMP are to eliminate potential hazards to the public and the environment that are associated with contamination at SFMP sites and to make surplus real property available for other uses, to the extent possible. The objectives of the EE/CA report are to identify the cleanup as a removal action, to document the selection of response activities that will mitigate the potential for release of radioactive or chemical contaminant for the quarry water into the nearby environment, and to address environmental impacts associated with the proposed action. Pursuant to the evaluation alternatives in this report, it is proposed that the water be pumped from the quarry pond to a newly constructed treatment plant for removal of the contaminants of concern. This removal action is necessary for and consistent with the overall response action being planned to minimize potential threats to the public and the environment associated with the current contamination at the quarry. 66 refs., 15 figs., 32 tabs

  17. Handling of quarry waste from schist production at Oppdal, Norway

    Science.gov (United States)

    Willy Danielsen, Svein; Alnæs, Lisbeth; Azrague, Kamal; Suleng, Jon

    2017-04-01

    Handling of quarry waste from schist production at Oppdal, Norway Svein Willy Danielsen1), Lisbeth Alnæs2), Kamal Azrague2), Jon Suleng3) 1) Geomaterials Consultant, Trondheim Norway, 2) SINTEF, Trondheim, Norway, 3) AF Gruppen AS, Oppdal, Norway A significant amount of aggregate research in Norway has been focused on the recovery and use of surplus sizes from hard rock aggregate quarries. The use of sand sized quarry waste (QW) from crushing/processing has been motivated by the rapid depletion of traditional sand/gravel resources, increasing land-use conflicts, and the need to minimise QW deposits which for some quarries are becoming a critical factor for economy as well as for environmental reasons. With an annual aggregate production of 77 million tons, out of which approximately 83 % comes from hard rock, the annual volume of size market, the economic - and also environmental - potential will be considerable. Understanding the geological conditions and petrographic properties of the rock is vital. This is a quartz-feldspar rich metamorphic rock - a meta-arkose - containing rhythmically distributed planar lamina (less than 2 mm thick) or scattered occurrence of mica, separated by layers composed predominately of quartz and feldspar. The rock can be split along the lamina to slabs varying from 0.5 cm to more than 10 cm in thickness, and the microstructure can be characterized as being granoblastic to gneissic. . This makes it possible by well designed crushing process and careful selection of the in-going rock particles, to obtain well shaped aggregates up to at least 20 mm. The on-going project will also study the total cost situation depending on the QW utilisation, discuss the environmental and sustainability issues with a societal perspective, and also consider the market opportunities.

  18. Fungi and their biomass in detritus of the seagrass Thalassia hemprichii (Ehrenberg) Ascherson

    Digital Repository Service at National Institute of Oceanography (India)

    Sathe, V.; Raghukumar, S.

    Kalpeni Island revealed different kinds of hyphae and unicellular thraustochytrid fungi, particularly in later stages of decomposition. Highest values of biomass estimatEd. by direct observations were 31840 x 10-6 g mycelial fungi per g dry wt. detritus...

  19. Recycling of quarry waste as part of sustainable aggregate production: Norwegian and Italian point of view

    Science.gov (United States)

    Antonella Dino, Giovanna; Willy Danielsen, Svein; Chiappino, Claudia; Primavori, Piero; Engelsen, Christian John

    2016-04-01

    Resource preservation is one of the main challenges in Europe, together with waste management and recycling; recently several researchers are interested in the recovering of critical raw materials and secondary raw materials from landfill. Aggregate supply, even if it is not "critical" sensus stricto (s.s.), is one of the European priorities (low value but high volume needs). On the other side, the management of quarry waste , mainly from dimension stones, but also as fines from aggregate crushing, is still a matter of concern. Such materials are managed in different ways both locally and nationwide, and often they are landfilled, because of an unclear legislation and a general lack of data. Most of time the local authorities adopt the maximum precaution principle or the enterprises find it little profitable to recover them, so that the sustainable recycling of such material is not valued. Several studies have shown, depending on the material specific characteristics, the viability of recycling quarry waste into new raw materials used in glass and ceramic industries, precast concrete production, infrastructures etc. (Loudes et al. 2012, Dino&Marian 2015, Bozzola et al 2012, Dino et al. 2012, etc.). Thus, aggregate production may be one of the profitable ways to use quarry waste and is falling under the priority of EU (aggregate supply). Positive economic and environmental effects are likely to be achieved by systematic recycling of quarry waste planned by industries (industrial planning) and public authorities (national and local planning of aggregate exploitation). Today, the recycling level varies to a great extent and systematic recovery is not common among European Countries. In Italy and Norway no significant incentives on recycling or systematic approaches for local aggregate exploitation exist. The environmental consequences can be overexploitation of the natural resources, land take for the landfills, environmental contamination and landscape alteration by

  20. Responses of soil fungal community to the sandy grassland restoration in Horqin Sandy Land, northern China.

    Science.gov (United States)

    Wang, Shao-Kun; Zuo, Xiao-An; Zhao, Xue-Yong; Li, Yu-Qiang; Zhou, Xin; Lv, Peng; Luo, Yong-Qing; Yun, Jian-Ying

    2016-01-01

    Sandy grassland restoration is a vital process including re-structure of soils, restoration of vegetation, and soil functioning in arid and semi-arid regions. Soil fungal community is a complex and critical component of soil functioning and ecological balance due to its roles in organic matter decomposition and nutrient cycling following sandy grassland restoration. In this study, soil fungal community and its relationship with environmental factors were examined along a habitat gradient of sandy grassland restoration: mobile dunes (MD), semi-fixed dunes (SFD), fixed dunes (FD), and grassland (G). It was found that species abundance, richness, and diversity of fungal community increased along with the sandy grassland restoration. The sequences analysis suggested that most of the fungal species (68.4 %) belonged to the phylum of Ascomycota. The three predominant fungal species were Pleospora herbarum, Wickerhamomyces anomalus, and Deconica Montana, accounting for more than one fourth of all the 38 species. Geranomyces variabilis was the subdominant species in MD, Pseudogymnoascus destructans and Mortierella alpine were the subdominant species in SFD, and P. destructans and Fungi incertae sedis were the dominant species in FD and G. The result from redundancy analysis (RDA) and stepwise regression analysis indicated that the vegetation characteristics and soil properties explain a significant proportion of the variation in the fungal community, and aboveground biomass and C:N ratio are the key factors to determine soil fungal community composition during sandy grassland restoration. It was suggested that the restoration of sandy grassland combined with vegetation and soil properties improved the soil fungal diversity. Also, the dominant species was found to be alternative following the restoration of sandy grassland ecosystems.

  1. Quarry waste management and recovery: first results connected to Carrara marble ravaneti (Italy)

    Science.gov (United States)

    Antonella Dino, Giovanna; Chiappino, Claudia; Rossetti, Piergiorgio

    2017-04-01

    Quarry waste (QW) represents a huge economic and environmental issue, due to loss of resources and to economic and environmental costs connected to waste management and landfilling activities. In many cases, valuable Raw Materials (RM) and Secondary Raw Materials (SRM) can be supplied by enhancing the QW recovery. In Italy large amounts of QW have been and still are dumped: such materials, if their quality (chemical, mineralogical, physical characteristics) and quantity are adequate, and if the impacts connected to their management are positive, can represent a valuable resource for SRM exploitation. Several dimension stone quarries have been and are interested by researches as for QW exploitation. Some researches show positive results, which are the basis for QW recovery (both from waste streams and from quarry dumps exploitation): a noticeable example is represented by Carrara marble waste. The Carrara quarry basin is characterized by ca. one hundred quarries for colored and white marble exploitation. The waste production can be summarized in: 80 Mm3 waste present in old quarry dumps (Ravaneti) and 3 Mm3/y of waste stream from quarrying activities. At present only 0.5 Mm3/y of QW is exploited for SRM production, causing a huge loss of resource. This has been the background for a preliminary research, on Carrara marble Ravaneti characterization, which was carried out thanks to the close cooperation between University of Torino, Società Apuana Marmi srl, and SET srl. In 2015, two QW dumping areas, Calocara and Lorano, were selected as representative for sampling activities. Three main sample categories were individuated based on granulometry (0.5-4 mm, 0-25 mm, 0-150 mm) to be characterized (size distribution, density, Atterberg limits, Los Angeles test, freezing and heat tests, flat and shape indexes, geochemistry, mineralogy). The results obtained are promising: the physical characterization shows an attitude for Carrara QW to be recovered as crushed materials

  2. Respirable dust and quartz exposure from three South African farms with sandy, sandy loam, and clay soils.

    Science.gov (United States)

    Swanepoel, Andrew J; Kromhout, Hans; Jinnah, Zubair A; Portengen, Lützen; Renton, Kevin; Gardiner, Kerry; Rees, David

    2011-07-01

    To quantify personal time-weighted average respirable dust and quartz exposure on a sandy, a sandy loam, and a clay soil farm in the Free State and North West provinces of South Africa and to ascertain whether soil type is a determinant of exposure to respirable quartz. Three farms, located in the Free State and North West provinces of South Africa, had their soil type confirmed as sandy, sandy loam, and clay; and, from these, a total of 298 respirable dust and respirable quartz measurements were collected between July 2006-November 2009 during periods of major farming operations. Values below the limit of detection (LOD) (22 μg · m(-3)) were estimated using multiple 'imputation'. Non-parametric tests were used to compare quartz exposure from the three different soil types. Exposure to respirable quartz occurred on all three farms with the highest individual concentration measured on the sandy soil farm (626 μg · m(-3)). Fifty-seven, 59, and 81% of the measurements on the sandy soil, sandy loam soil, and clay soil farm, respectively, exceeded the American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) of 25 μg · m(-3). Twelve and 13% of respirable quartz concentrations exceeded 100 μg · m(-3) on the sandy soil and sandy loam soil farms, respectively, but none exceeded this level on the clay soil farm. The proportions of measurements >100 μg · m(-3) were not significantly different between the sandy and sandy loam soil farms ('prop.test'; P = 0.65), but both were significantly larger than for the clay soil farm ('prop.test'; P = 0.0001). The percentage of quartz in respirable dust was determined for all three farms using measurements > the limit of detection. Percentages ranged from 0.5 to 94.4% with no significant difference in the median quartz percentages across the three farms (Kruskal-Wallis test; P = 0.91). This study demonstrates that there is significant potential for over-exposure to respirable quartz in

  3. A new major adze quarry from Nanakuli, O'ahu: implications for interaction studies in Hawai'i

    International Nuclear Information System (INIS)

    Weisler, M.I.; Collins, S.L.; Feng, Y.; Zhao, J.; Shipton, C.; Wei, S.

    2013-01-01

    A major new basalt adze quarry at Nanakuli Valley, Hawaiian Islands is described which now ranks as one of the two largest on O'ahu and aside from the Mauna Kea adze quarry complex on Hawai'i island and the Haleakala source on Maui, is one of the major quarries in the archipelago. We defined the approximate limits of the quarry complex, located the in situ geological source of the fine-grained basalt used for adze manufacture, report the petrographic and geochemical variability of the source rock, and describe the adze reduction strategies from analysis of adze blanks and preforms, as well as hammerstones and debitage. The geochemical variation of the nine source rocks and artefacts were defined by a comprehensive array of 10 fully quantitative major element concentrations, 43 trace element abundances, and high-precision Sr-Nd-Pb isotopic ratios obtained using the state-of-the-art Thermal Ionization Mass Spectrometry (TIMS, for Sr isotopes), Multi-Collector Inductively Coupled Plasma Mass Spectrometry (MC-ICP-MS, for Nd-Pb isotopes), quadrupole ICP-MS (for trace elements) and Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES, for major elements), respectively. A piece of branch coral was recovered from the surface of a rockshelter that provided a U-series date of possible quarry use in the mid-13th century. It is advocated that a comprehensive range of major and trace element concentrations and Sr-Nd-Pb isotopic ratios are required for geochemically characterising adze quarries to facilitate the long-term viability of sourcing studies. (author)

  4. IMPLEMENTASI SANDI HILL UNTUK PENYANDIAN CITRA

    Directory of Open Access Journals (Sweden)

    JJ Siang

    2002-01-01

    Full Text Available Hill's code is one of text encoding technique. In this research, Hill's code is extended to image encoding. The image used is BMP 24 bit format. 2x2 and 3x3 matrices is used as a key. The results show that Hill's code is suitable for image whose RGB values vary highly. On the contrary, it is not suitable for less varied RGB images since its original pattern is still persisted in encrypted image. Hill's code for image encoding has also disadvantage in the case that the key matrix is not unique. However, for daily application, with good key matrix, Hill's code can be applied to encode image since it's process only deals with simple matrix operation so it become fast. Abstract in Bahasa Indonesia : Sandi Hill merupakan salah satu teknik penyandian teks. Dalam penelitian ini, pemakaian sandi Hill diperluas dari teks ke citra bertipe BMP 24 bit. Matriks yang dipakai berordo 2x2 dan 3x3. Hasil percobaan menunjukkan bahwa sandi Hill cocok untuk enkripsi citra dengan variasi nilai RGB antar piksel berdekatan yang tinggi (seperti foto, tapi tidak cocok untuk citra dengan variasi nilai RGB yang rendah (seperti gambar kartun karena pola citra asli masih tampak dalam citra sandi. Sandi Hill juga memiliki kelemahan dalam hal tidak tunggalnya matriks kunci yang dapat dipakai. Akan tetapi untuk pemakaian biasa, dengan pemilihan matriks kunci yang baik, sandi Hill dapat dipakai untuk penyandian karena hanya melibatkan operasi matriks biasa sehingga prosesnya relatif cepat. Kata kunci: Sandi Hill, Citra, Relatif Prima.

  5. The use of ground penetrating radar (GPR) in the investigation of historical quarry abandonment in Svalbard

    NARCIS (Netherlands)

    Koster, Benjamin; Kruse, Frigga

    2016-01-01

    This paper investigates historical quarry abandonment in Svalbard in the European High Arctic. A short-lived British marble quarry in Kongsfjorden lay deserted after 1920. We ask why this attempt at the large-scale development of High Arctic marble was unproductive; whether there are structural

  6. Superfund record of decision (EPA Region 7): Weldon Spring Quarry/Plant/Pits (USDOE), St. Charles, MO, September 30, 1998

    International Nuclear Information System (INIS)

    1999-03-01

    The Weldon Spring Quarry is one of two noncontiguous areas that constitute the US Department of Energy's (DOE) Weldon Spring site. The main area of the site is the chemical plant. Both areas are located in St. Charles County, Missouri, about 48 km (30 mi) west of St. Louis. The US Environmental Protection Agency (EPA) listed the quarry on the National Priorities List (NPL) in 1987, and the chemical plant area was added to the list in 1989. The quarry is about 6.4 km (4 mi) south-southwest of the chemical plant area; it is accessible from State Route 94 and is currently fenced and closed to the public. The quarry is approximately 300 m (1,000 ft) long by 140 m (450 ft) wide and covers an area of approximately 3.6 ha (9 acres). The quarry was used by the Army for disposal of chemically contaminated (explosive) materials in the 1940s and was later used for the disposal of radioactively contaminated material by the Atomic Energy Commission (AEC) in the 1960s. Approximately 110,000 m 3 (144,000 yd 3 ) of soil and waste material was removed from the quarry and transported to the chemical plant area as part of completing the remedial action stipulated in the Record of Decision (ROD) for the Quarry Bulk Waste Operable Unit (DOE 1990). Bulk waste removal was completed in October 1995. These wastes have been placed in the disposal cell at the chemical plant. Prior to bulk waste removal, contaminated water contained in the quarry pond was also removed; approximately 170 million liters (44 million gal) have been treated as of March 1998

  7. Behavior and Release of Nitrogen at Mines and Quarries in Nordic Conditions

    Science.gov (United States)

    Karlsson, Teemu; Neitola, Raisa; Jermakka, Johannes; Merta, Elina; Mroueh, Ulla-Maija

    2015-04-01

    The increased extraction of mineral resources and mining activities creates added pressure on the environmental issues and a proper water management in mining areas in Finland. Among others, nitrogen compounds released from explosives or from mining processes can have a detrimental effect on the environment. Thus, this project aimed at comprehensive understanding on the nitrogen issue in the extractive industry. The project collected essential data on nitrogen compounds present in the environments of mines and quarries, and generated better understanding of the discharge and behaviour of nitrogen compounds in mining areas. The sources and balances of explosives-originated nitrogen compounds at mines and quarries of different sizes were investigated and compared. Additionally, the focus was in 'nitrogen smudging' problem of waste rocks and the intensity, as well as evolution and chemical characteristics of their nitrogen contamination. According to the results, the total load of potential nitrogen to the environment depends on the scale and type of the activity as well as the type of explosives used. The main emission sources of nitrogen are process and dewatering waters. A lysimeter study showed that the explosives originated nitrogen content of left over stones from natural stone quarrying is relatively low and ca. half of the nitrogen is leached within the first weeks after detonation. The "nitrogen smudging" of natural stone quarrying left over stones is relatively low to begin with and enhanced by the rapid flushing by rainwater, thus the residues of explosives should not be considered to prevent the utilization of otherwise mineralogically inert waste rocks of good technical quality. The overall nitrogen management should take into account the background concentrations and sensitivity of the local ecosystem. The research project "Solution for Control of Nitrogen Discharges at Mines and Quarries, (MINIMAN)" was realized during years 2012-2014 as a cooperative

  8. Application of classic engineering techniques (value engineering and observational method) at the Weldon Spring Quarry

    International Nuclear Information System (INIS)

    Ferguson, R.D.; Valett, G.L.

    1991-01-01

    In July of 1987 the Weldon Spring quarry was listed on the Environmental Protection Agency National Priority List as the highest priority Federal facility site. The Weldon Spring Site Remedial Action Project applied the principles and techniques of Value Engineering (VE) and the Observational Method to remedial planning efforts at the quarry. VE sessions resulted in modifications of the scenarios developed during the Remedial Investigation/Feasibility Study (RM) process in preparation for conceptual design activities for the removal of waste from the quarry. The Observational Method, a technique developed to manage uncertainties, was used to guide both environmental and engineering planning to ensure that the waste removal activities win be carried out in a safe and environmentally responsible manner

  9. Baseline risk assessment for the quarry residuals operable unit of the Weldon Spring Site, Weldon Spring, Missouri

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-02-01

    The U.S. Department of Energy (DOE) is conducting cleanup activities at the Weldon Spring site, located in St. Charles County, Missouri, about 48 km (30 mi) west of St. Louis. Cleanup of the site consists of several integrated components. The quarry residuals operable unit (QROU), consisting of the Weldon Spring quarry and its surrounding area, is one of four operable units being evaluated. In accordance with requirements of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended, DOE is conducting a remedial investigation/feasibility study (RI/FS) to determine the proper response to address various contaminated media that constitute the QROU. Specifically, the operable unit consists of the following areas and media: the residual material remaining at the Weldon Spring quarry after removal of the pond water and the bulk waste; groundwater underlying the quarry and surrounding area; and other media located in the surrounding vicinity of the quarry, including surface water and sediment at Femme Osage Slough, Little Femme Osage Creek, and Femme Osage Creek. An initial evaluation of conditions at the quarry area identified remaining data requirements needed to support the conceptual site exposure and hydrogeological models. These data requirements are discussed in the RI/FS work plan issued in January 1994. Soil contamination located at a property adjacent to the quarry, referred to as Vicinity Property 9 (VP9), was originally part of the scope of the QROU, as discussed in the work plan. However, a decision was subsequently made to remediate this vicinity property as part of cleanup activities for the chemical plant operable unit, as provided for in the Record of Decision (ROD). Remediation of VP9 was completed in early 1996. Hence, this baseline risk assessment (BRA) does not address VP9.

  10. Baseline risk assessment for the quarry residuals operable unit of the Weldon Spring Site, Weldon Spring, Missouri

    International Nuclear Information System (INIS)

    1998-02-01

    The U.S. Department of Energy (DOE) is conducting cleanup activities at the Weldon Spring site, located in St. Charles County, Missouri, about 48 km (30 mi) west of St. Louis. Cleanup of the site consists of several integrated components. The quarry residuals operable unit (QROU), consisting of the Weldon Spring quarry and its surrounding area, is one of four operable units being evaluated. In accordance with requirements of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended, DOE is conducting a remedial investigation/feasibility study (RI/FS) to determine the proper response to address various contaminated media that constitute the QROU. Specifically, the operable unit consists of the following areas and media: the residual material remaining at the Weldon Spring quarry after removal of the pond water and the bulk waste; groundwater underlying the quarry and surrounding area; and other media located in the surrounding vicinity of the quarry, including surface water and sediment at Femme Osage Slough, Little Femme Osage Creek, and Femme Osage Creek. An initial evaluation of conditions at the quarry area identified remaining data requirements needed to support the conceptual site exposure and hydrogeological models. These data requirements are discussed in the RI/FS work plan issued in January 1994. Soil contamination located at a property adjacent to the quarry, referred to as Vicinity Property 9 (VP9), was originally part of the scope of the QROU, as discussed in the work plan. However, a decision was subsequently made to remediate this vicinity property as part of cleanup activities for the chemical plant operable unit, as provided for in the Record of Decision (ROD). Remediation of VP9 was completed in early 1996. Hence, this baseline risk assessment (BRA) does not address VP9

  11. Proposed plan for remedial action at the quarry residuals operable unit of the Weldon Spring Site

    International Nuclear Information System (INIS)

    1998-03-01

    This proposed plan addresses the management of contamination present in various components of the quarry residuals operable unit (QROU) of the Weldon Spring site, which is located in St. Charles County, Missouri. The QROU consists of (1) residual waste at the quarry proper; (2) the Femme Osage Slough, Little Femme Osage Creek, and Femme Osage Creek; and (3) quarry groundwater located primarily north of the slough. Potential impacts to the St. Charles County well field downgradient of the quarry area are also being addressed as part of the evaluations for this operable unit. Remedial activities for the QROU will be conducted by the US Department of Energy (DOE) in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. As part of the remedial investigation/feasibility study (RI/FS) process required for the QROU under CERCLA, three major evaluation documents have been prepared to support cleanup decisions for this operable unit. decisions for this operable unit

  12. Analytic hierarchy process helps select site for limestone quarry expansion in Barbados.

    Science.gov (United States)

    Dey, Prasanta Kumar; Ramcharan, Eugene K

    2008-09-01

    Site selection is a key activity for quarry expansion to support cement production, and is governed by factors such as resource availability, logistics, costs, and socio-economic-environmental factors. Adequate consideration of all the factors facilitates both industrial productivity and sustainable economic growth. This study illustrates the site selection process that was undertaken for the expansion of limestone quarry operations to support cement production in Barbados. First, alternate sites with adequate resources to support a 25-year development horizon were identified. Second, technical and socio-economic-environmental factors were then identified. Third, a database was developed for each site with respect to each factor. Fourth, a hierarchical model in analytic hierarchy process (AHP) framework was then developed. Fifth, the relative ranking of the alternate sites was then derived through pair wise comparison in all the levels and through subsequent synthesizing of the results across the hierarchy through computer software (Expert Choice). The study reveals that an integrated framework using the AHP can help select a site for the quarry expansion project in Barbados.

  13. Ecosystem and physiological scales of microbial responses to nutrients in a detritus-based stream: results of a 5-year continuous enrichment

    Science.gov (United States)

    Keller Suberkropp; Vladislav Gulis; Amy D. Rosemond; Jonathan Benstead

    2010-01-01

    Our study examined the response of leaf detritus–associated microorganisms (both bacteria and fungi) to a 5-yr continuous nutrient enrichment of a forested headwater stream. Leaf litter dominates detritus inputs to such streams and, on a system wide scale, serves as the key substrate for microbial colonization. We determined physiological responses as microbial biomass...

  14. Hurricane Sandy Poster (October 29, 2012)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Hurricane Sandy poster. Multi-spectral image from Suomi-NPP shows Hurricane Sandy approaching the New Jersey Coast on October 29, 2012. Poster size is approximately...

  15. Baseline risk evaluation for exposure to bulk wastes at the Weldon Spring Quarry, Weldon Spring, Missouri

    International Nuclear Information System (INIS)

    Haroun, L.A.; Peterson, J.M.; MacDonell, M.M.; Hlohowskyj, I.

    1990-01-01

    The US Department of Energy (DOE), under its Surplus Facilities Management Program (SFMP), is responsible for cleanup activities at the Weldon Spring site, Weldon Spring, Missouri. The site consists of a raffinate pits and chemical plant area and a quarry. This baseline risk evaluation has been prepared to support a proposed response action for management of contaminated bulk wastes in the quarry. The quarry became chemically and radioactively contaminated as a result of various wastes that were disposed of there between 1942 and 1969. This risk evaluation assesses potential impacts on human health and the environment that may result from exposure to releases of contaminants from the quarry under current site conditions. Risk assessment is a key component of the remedial investigation/feasibility study (RI/FS) process, as identified in guidance from the US Environmental Protection Agency (EPA); this process addresses sites subject to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) of 1980, as amended by the Superfund Amendments and Reauthorization Act of 1986. Response actions at the Weldon Spring quarry are subject to CERCLA requirements because the quarry is listed on the EPA's National Priorities List. The DOE is also responsible for complying with the requirements of the National Environmental Policy Act (NEPA) of 1969, which requires federal agencies to consider the environmental consequences of a proposed action as part of the decision-making process for that action. Although this document has not been prepared to fulfill specific NEPA requirements, the analyses contained herein --- along with the analyses provided in the remedial investigation, feasibility study, and other supporting documents --- are intended to meet the environmental assessment requirements of NEPA

  16. CONGLOMERATE ROCKS "BRECCIA VERDE ANTICA" ARCHAEOLOGY, PETROLOGY, DETERIORATION AND TECHNOLOGY OF QUARRYING AT HAMMAMAT QUARRIES IN THE EASTEREN DESERT.

    Directory of Open Access Journals (Sweden)

    dr.HESHAM ABBAS KMALLY

    2010-01-01

    Full Text Available One of the most interesting of the monumental rocks of Egypt is the green conglomerates of the Hammamat valley which was used for bowls, vessels, sarcophagus and other objects, from a very early period. The quarries of wadi Hammamat produced the green ornamental stone known in Roman period as "Breccia verde antica". Generally the ancient conglomerate was used occasionally in Egypt at pharaonic time and late period, but it was quarried chiefly by the Roman for export to Italy. The conglomerate rocks range from coarse to fine conglomerates. They are composed of great assortment of rock fragments such as meta-sediments, meta-volcanic and granites. Some pebbles of the coarse conglomerates are previously deposited conglomerates. Pollution, humidity or moisture, solar radiation, rainfall and groundwater represent important factors for disintegration of green conglomerate rocks. Many types of destruction have been noted such as micro-cracks, fractures, joints, exfoliation, crumbling, discoloration, leaching and staining with iron oxides. The conglomerate rock sometimes changes into fragmented, soft residual and parent matter of the soil. Moreover, individual grains of feldspar and quartz begin to become loosened and the rock shows superficial granular disintegration due to, growth of salts and physiochemical weathering

  17. Mineralization of Surfactants by the Microbiota of Submerged Plant Detritus

    OpenAIRE

    Federle, Thomas W.; Ventullo, Roy M.

    1990-01-01

    In wetlands and canopied bodies of water, plant detritus is an important source of carbon and energy. Detrital materials possess a large surface area for sorption of dissolved organics and are colonized by a large and diverse microbiota. To examine the biodegradation of surfactants by these microorganisms, submerged oak leaves were obtained from a laundromat wastewater pond, its overflow, and a pristine control pond. Leaves were cut into disks and incubated in sterile water amended with 50 μg...

  18. A methodological framework to assess the socio-economic impact of underground quarries: A case study from Belgian Limburg.

    Science.gov (United States)

    Sergeant, A; Poesen, J; Duchateau, P; Vranken, L

    2016-01-15

    This study developed a methodology to assess the socio-economic impact of the presence and collapse of underground limestone quarries. For this we rely on case study evidence from Riemst, a village located in Eastern Belgium and use both secondary and primary data sources. A sinkhole inventory as well as data about the prevention costs provided by the municipality was used. To estimate the recreational values of the quarries, visitor data was obtained from the tourist office of Riemst. Next, two surveys were conducted among inhabitants and four real estate agents and one notary. The direct and indirect damages were assessed using respectively the repair cost and production and real estate value losses. The total yearly direct and indirect damage equals €415000 (±€85000) and more than half of it can be attributed to the depreciation of real estate (€230000). The quarries have recreational, cultural-historical and ecological values and thus generate societal benefits. The yearly recreational value was at least €613000 in 2012 values. The ecological and cultural-historical values augment to €180000 per year (in 2012 values). Further, our study indicates that the gains from filling up the quarries below the houses located above an underground limestone quarry outweigh the costs in the case study area. The net gain from filling up the underground quarry ranges €38700 to €101700 per house. This is only the lower bound of the net gain from filling up these underground quarries since preventive filling makes future collapses less likely so that future direct repair costs will be most likely smaller. Copyright © 2015 Elsevier B.V. All rights reserved.

  19. Long-term influence of tillage and fertilization on net carbon dioxide exchange rate on two soils with different textures.

    Science.gov (United States)

    Feiziene, Dalia; Feiza, Virginijus; Slepetiene, Alvyra; Liaudanskiene, Inga; Kadziene, Grazina; Deveikyte, Irena; Vaideliene, Asta

    2011-01-01

    The importance of agricultural practices to greenhouse gas mitigation is examined worldwide. However, there is no consensus on soil organic carbon (SOC) content and CO emissions as affected by soil management practices and their relationships with soil texture. No-till (NT) agriculture often results in soil C gain, though, not always. Soil net CO exchange rate (NCER) and environmental factors (SOC, soil temperature [T], and water content [W]), as affected by soil type (loam and sandy loam), tillage (conventional, reduced, and NT), and fertilization, were quantified in long-term field experiments in Lithuania. Soil tillage and fertilization affected total CO flux (heterotrophic and autotrophic) through effect on soil SOC sequestration, water, and temperature regime. After 11 yr of different tillage and fertilization management, SOC content was 23% more in loam than in sandy loam. Long-term NT contributed to 7 to 27% more SOC sequestration on loam and to 29 to 33% more on sandy loam compared with reduced tillage (RT) or conventional tillage (CT). Soil water content in loam was 7% more than in sandy loam. Soil gravimetric water content, averaged across measurement dates and fertilization treatments, was significantly less in NT than CT and RT in both soils. Soil organic carbon content and water storage capacity of the loam and sandy loam soils exerted different influences on NCER. The NCER from the sandy loam soil was 13% greater than that from the loam. In addition, NCER was 4 to 9% less with NT than with CT and RT systems on both loam and sandy loam soils. Application of mineral NPK fertilizers promoted significantly greater NCER from loam but suppressed NCER by 15% from sandy loam. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  20. Whole-system nutrient enrichment increases secondary production in a detritus-based ecosystem

    Science.gov (United States)

    W.F. Cross; J.B. Wallace; A.D. Rosemond; S.L. Eggert

    2006-01-01

    Although the effects of nutrient enrichment on consumer-resource dynamics are relatively well studied in ecosystems based on living plants, little is known about the manner in which enrichment influences the dynamics and productivity of consumers and resources in detritus-based ecosystems. Because nutrients can stimulate loss of carbon at the base of detrital food webs...

  1. Responsiveness summary for the remedial investigation/feasibility study for management of the bulk wastes at the Weldon Spring quarry, Weldon Spring, Missouri

    International Nuclear Information System (INIS)

    Peterson, J.M.; MacDonell, M.M.

    1990-08-01

    The US Department of Energy (DOE) is responsible for conducting remedial actions at the Weldon Spring site in St. Charles County, Missouri, under its Surplus Facilities Management Program. The site consists of a quarry and a chemical plant area located about 6.4 km (4 mi) northeast of the quarry. The quarry is surrounded by the Weldon Spring Wildfire Area and is near an alluvial well field that constitutes a major source of potable water for St. Charles County; the nearest supply well is located about 0.8 km (0.5 mi) southeast of the quarry. From 1942 to 1969, the quarry was used for the disposal of various radioactively and chemically contaminated materials. Bulk wastes in the quarry consist of contaminated soils and sediments, rubble, metal debris, and equipment. As part of overall site remediation, DOE is proposing to conduct an interim remedial action at the quarry to manage the radioactively and chemically contaminated bulk wastes contained therein. Potential remedial action alternatives for managing the quarry bulk wastes have been evaluated consistent with US Environmental Protection Agency (EPA) guidance for conducting remedial actions under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. The contents of these documents were developed in consultation with EPA Region VII and the state of Missouri and reflect the focused scope defined for this interim remedial action. 9 refs

  2. Stream Insect Production as a Function of Alkalinity and Detritus Processing

    OpenAIRE

    Osborn, Thomas G.

    1981-01-01

    The study was conducted to determine if aquatic insect production was significantly different between high and low alkalinity mountain streams and if any differences were associated with food availability factors. The major objectives included determining: (1) if annual production differences occur between high and low alkalinity streams; (2) if processing rates of terrestrial detritus differs between high and low alkalinity streams; (3) if detrital processing rates are related to stream inse...

  3. Use of the McQuarrie equation for the computation of shear viscosity via equilibrium molecular dynamics

    International Nuclear Information System (INIS)

    Chialvo, A.A.; Debenedetti, P.G.

    1991-01-01

    To date, the calculation of shear viscosity for soft-core fluids via equilibrium molecular dynamics has been done almost exclusively using the Green-Kubo formalism. The alternative mean-squared displacement approach has not been used, except for hard-sphere fluids, in which case the expression proposed by Helfand [Phys. Rev. 119, 1 (1960)] has invariably been selected. When written in the form given by McQuarrie [Statistical Mechanics (Harper ampersand Row, New York, 1976), Chap. 21], however, the mean-squared displacement approach offers significant computational advantages over both its Green-Kubo and Helfand counterparts. In order to achieve comparable statistical significance, the number of experiments needed when using the Green-Kubo or Helfand formalisms is more than an order of magnitude higher than for the McQuarrie expression. For pairwise-additive systems with zero linear momentum, the McQuarrie method yields frame-independent shear viscosities. The hitherto unexplored McQuarrie implementation of the mean-squared displacement approach to shear-viscosity calculation thus appears superior to alternative methods currently in use

  4. Effect of Different Levels of Irrigation Water Salinity and Soil Texture on Growth and N Use Efficiency of Tomato and Melochia Grown in Rotation using 15N

    International Nuclear Information System (INIS)

    Darwish, T.M.; El Moujabber, M.; Atallah, T.; El Chami, D.

    2008-01-01

    Increasing water demands and water scarcity imply large farmer's reliance on groundwater on the coastal area leading to water salinization by seawater intrusion. Irrigation using saline water accumulates salts in the soil notably under protected agriculture leading to negative impact on yields. Consequently salt removal by leaching is required. Bioremediation of salt affected soils through a rotation acquires economic and environmental importance. Pot experiments were conducted under plastic house conditions on sandy soil (T1) and clay soil (T2). Three saline water treatments were used: low (S1=1.0 dS.m-1), moderate (S2=2.5 dS.m-1) and high (S3=5.0 dS.m-1). Tomato cv Tyrade (S and G seeds) was planted first, followed by Melochia or Jew's mallow (Corchorus olitorius) for remediation purposes. Each soil was placed in 24 pots and treatments were distributed randomly. Fertigation was done using drip method. Labeled nitrogen 15 N was used to trace the direct and residual effect of nitrogen under different saline conditions. Tomato yield, for the sandy soil, was negatively affected by the higher level of salinity. This effect could be attributed to the smaller buffering capacity of the sand soil. As a result of salinity, there was a remarkable increase in dry matter contents of fruits in the sandy soil only. Texture had a major effect on leaf area index (LAI) with better development in clay soil. Water consumption in the first 200 days of growth period did not show any significant difference among treatments with around 350-375 mm consumed. Nitrogen derived from fertilizers (% Ndff) was not affected by the soil texture or by the salinity. N yield and use efficiency were higher in the clay soil texture. Moreover, yield and Ndff in Melochia plants were negatively affected due to salt accumulation in the soil. Counting for all recovered N in the tomato-Melochia rotation, N use efficiency was higher in plants grown on clay soil (47%) compared to sandy soil (37.5%). (author)

  5. Consolidation and compaction as a means to prevent settlement of bentonite/sandy silt mixes for use in waste disposal sites

    International Nuclear Information System (INIS)

    Abeele, W.V.

    1985-01-01

    The texture of the local Los Alamos tuff is that of a sandy silt with a high hydraulic conductivity. The permeability is dramatically decreased by addition of small amounts of bentonite. The coefficient of consolidation for bentonite/sandy silt ratios decreases inversely proportional with the square of that ratio, whereas the compression index, the swelling index, and the permeability change index increase with increasing bentonite ratio. A strong relationship also exists between the void ratio and the logarithm of the applied stress for any given bentonite ratio. The empirical linear relationship between the void ratio and the logarithm of the applied stress, developed by Taylor, is excellent and enables us to limit the evaluation of conductivity at any void ratio to the measurement of the initial and the desired void ratio, the initial conductivity, and the permeability change index. The decrease in void ratio caused by consolidation or natural compaction of the mixes are scrutinized. Examples of expected settlement and subsidence are calculated based on the known geotechnical characteristics of bentonite/sandy silt mixes. Remedial actions, i.e., means to limit the amount of settlement, are considered. We finally discuss our field experiment, which studies the influence of subsidence on layered systems in general and on biobarriers in particular. 15 refs., 5 tabs

  6. Ground beetles (Carabidae on quarry terraces in the vicinity of Brno (Czech Republic

    Directory of Open Access Journals (Sweden)

    Lucie Novotná

    2012-01-01

    Full Text Available The occurrence of ground beetles (Carabidae, Coleoptera was monitored in the exhausted limestone quarry of massif Hády near Brno using formaldehyde pitfall traps with a monthly interval of collection. Research was conducted from April to October in 2009 and 2010. The obtained material was investigated on some synecological characteristics and species affiliation to bioindication groups. In total for both years, 462 specimens of 43 species were captured. Most species were found in habitats with vegetation cover in the immediate vicinity of cultivated agricultural land – 441 specimens of 39 species. In the quarry itself only a minimal amount of ground beetles was found – 21 specimens of 11 species. Decrease in the abundance of ground beetles towards the center of the quarry was demonstrated. Next, significant species of Brachinus crepitans, Brachinus explodens and Cicindela sylvicola (endangered species pursuant to Decree 395/1992 Coll. and species listed in the Red List were reported – near threatened Ophonus sabulicola and vulnerable Cylindera germanica (also endangered species pursuant to Decree 395/1992 Coll.

  7. Environmental Ionizing Radiation Survey of Quarry Sites in Ilorin ...

    African Journals Online (AJOL)

    NJABS

    Besides, human exposure to radiations may increase if they live in areas with radiation doses above normal background value. Hence, this study involves the determination of background ionizing radiation levels around quarry sites in the industrial area of Ilorin with a view to assessing whether the radiation level is within ...

  8. Interaction of different irrigation strategies and soil textures on the nitrogen uptake of field grown potatoes

    DEFF Research Database (Denmark)

    Ahmadi, S.H.; Andersen, Mathias Neumann; Lærke, Poul Erik

    2011-01-01

    Nitrogen (N) uptake (kg ha-1) of field-grown potatoes was measured in 4.32 m2 lysimeters that were filled with coarse sand, loamy sand, and sandy loam and subjected to full (FI), deficit (DI), and partial root-zone drying (PRD) irrigation strategies. PRD and DI as water-saving irrigation treatments...... in the loamy sand had the highest amount of N uptake. The interaction between irrigation treatments and soil textures was significant, and implied that under non-limiting water conditions, loamy sand is the suitable soil for potato production because plants can take up sufficient amounts of N and it could...... potentially lead to higher yield. However, under limited water conditions and applying water-saving irrigation strategies, sandy loam and coarse sand are better growth media because N is more available for the potatoes. The simple yield prediction model was developed that could explains ca. 96...

  9. Subsidence hazards connected to quarrying activities in a karst area: the case of the Moncalvo sinkhole event (Piedmont, NW Italy

    Directory of Open Access Journals (Sweden)

    Bonetto, Sabrina

    2008-09-01

    Full Text Available Gypsum is an important raw material for constructions and other industrial sectors. In Piedmont (NW Italy, main gypsum bodies are located in the Monferrato area, where large open pits and underground quarries are present. The gypsum-bearing formation outcropping in this area shows typical geological, structural, and hydrogeological features, which affect the quarrying and the related interaction with natural phenomena, human activities, and land use. In particular, gypsum karst has considerable influence on mining operations, as well as mining operations can produce strong impact on gypsum karst. In Monferrato, a specific case of interaction between the quarrying activity and geological, hydrogeological, and territorial setting is represented by the event of water inrush that happened in the Moncalvo underground quarry in association with the development of a surface sinkhole phenomenon.

  10. Pulmonary Problems among Quarry Workers of Stone Crushing Industrial Site at Umuoghara, Ebonyi State, Nigeria

    Directory of Open Access Journals (Sweden)

    AN Nwibo

    2012-08-01

    Full Text Available Background: Respiratory problem is one of the major health hazards in dust-exposed workers; it is a major cause of morbidity and mortality all over the world. Objective: To determine the prevalence of respiratory problems and lung function impairment among quarry workers in Ebonyi State, Nigeria. Methods: Respiratory problems and lung function were studied in 403 quarry workers aged 10–60 years. Respiratory problems were investigated with a questionnaire based on international models adapted for the study population. Lung function was assessed by spirometry and chest roentgenography. Results: The respiratory problems found were chest pain (47.6%, occasional cough (40.7%, occasional shortness of breath (6.5% and wheezing (5.2%. The mean±SD FEV1 and FVC values were significantly decreased with length of exposure—respectively, 3.52±0.77 and 3.91±0.72 L for 10 years of exposure. Moreover, the mean±SD FEV1 and FVC values of smoker (3.37±0.81 and 3.56±1.02 L, respectively were significantly (p<0.05 lower than that of non-smokers (3.68±1.02 and 3.89±0.99 L, respectively working in the quarry site. Conclusion: Chronic exposure to dust due to stone quarrying may increase the risk of respiratory problems and impaired lung function—cigarette smokers are at higher risk.

  11. Himalayan sedimentary pulses recorded by silicate detritus within a ferromanganese crust from the Central Indian Ocean

    Digital Repository Service at National Institute of Oceanography (India)

    Banakar, V.K.; Galy, A.; Sukumaran, N.P.; Parthiban, G.; Volvaiker, A.Y.

    A Central Indian Ocean deep-water seamount hydrogenous ferromanganese crust (SS663-Crust) contains variable (7-23%) amounts of detrital material (silicate-detritus). Taking into account the growth rate of the authigenic component, the accumulation...

  12. Sandy PMO Disaster Relief Appropriations Act of 2013 Financial Data

    Data.gov (United States)

    Department of Homeland Security — Sandy PMO: Disaster Relief Appropriations Act of 2013 (Sandy Supplemental Bill) Financial Data. This is the Sandy Supplemental Quarterly Financial Datasets that are...

  13. Insights into the radial water jet drilling technology – Application in a quarry

    Directory of Open Access Journals (Sweden)

    Thomas Reinsch

    2018-04-01

    Full Text Available In this context, we applied the radial water jet drilling (RJD technology to drill five horizontal holes into a quarry wall of the Gildehaus quarry close to Bad Bentheim, Germany. For testing the state-of-the-art jetting technology, a jetting experiment was performed to investigate the influence of geological heterogeneity on the jetting performance and the hole geometry, the influence of nozzle geometry and jetting pressure on the rate of penetration, and the possibility of localising the jetting nozzle utilizing acoustic activity. It is observed that the jetted holes can intersect fractures under varying angles, and the jetted holes do not follow a straight path when jetting at ambient surface condition. Cuttings from the jetting process retrieved from the holes can be used to estimate the reservoir rock permeability. Within the quarry, we did not observe a change in the rate of penetration due to jetting pressure variations. Acoustic monitoring was partially successful in estimating the nozzle location. Although the experiments were performed at ambient surface conditions, the results can give recommendations for a downhole application in deep wells. Keywords: Acoustic monitoring, Drilling performance, Trajectory, Permeability, Rock properties, Radial water jet drilling (RJD

  14. Correlation between landscape fragmentation and sandy desertification: a case study in Horqin Sandy Land, China.

    Science.gov (United States)

    Ge, Xiaodong; Dong, Kaikai; Luloff, A E; Wang, Luyao; Xiao, Jun; Wang, Shiying; Wang, Qian

    2016-01-01

    The exact roles of landscape fragmentation on sandy desertification are still not fully understood, especially with the impact of different land use types in spatial dimension. Taking patch size and shape into consideration, this paper selected the Ratio of Patch Size and the Fractal Dimension Index to establish a model that reveals the association between the area of bare sand land and the fragmentation of different land use types adjacent to bare sand land. Results indicated that (1) grass land and arable land contributed the most to landscape fragmentation processes in the regions adjacent to bare sand land during the period 1980 to 2010. Grass land occupied 54 % of the region adjacent to bare sand land in 1980. The Ratio of Patch Size of grass land decreased from 1980 to 2000 and increased after 2000. The Fractal Dimension Index of grass increased during the period 1980 to 1990 and decreased after 1990. Arable land expanded significantly during this period. The Ratio of Patch Size of arable land increased from 1980 to 1990 and decreased since 1990. The Fractal Dimension Index of arable land increased from 1990 to 2000 and decreased after 2000. (2) The Ratio of Patch Size and the Fractal Dimension Index were significantly related to the area of bare sand land. The role of landscape fragmentation was not linear to sandy desertification. There were both positive and negative effects of landscape fragmentation on sandy desertification. In 1980, the Ratio of Patch Size and the Fractal Dimension Index were negatively related to the area of bare sand land, showing that the landscape fragmentation and regularity of patches contributed to the expansion of sandy desertification. In 1990, 2000, and 2010, the Ratio of Patch Size and the Fractal Dimension Index were mostly positively related to the area of bare sand land, showing the landscape fragmentation and regularity of patches contributed to the reversion of sandy desertification in this phase. The absolute values of

  15. Effect of shape and surface texture of aggregates during high intensity vertical shaft impact autogeneous crushing

    International Nuclear Information System (INIS)

    Samayamutthirian Palaniandy; Khairun Azizi Mohd Azizli

    2002-01-01

    The demand for quarry industry to produce high quality aggregates is increasing parallel with the demand of high strength concrete. Focus on the high quality aggregates production is very essential as 70% of the concrete consist of aggregates. High quality aggregate is characterised according to its shape, surface texture and its size distribution. The cubical and more equidimensional aggregates are characterised as high quality aggregates. Besides photomicrograph of aggregates, Flakiness and Elongation indices are important empirical measurements to determine the quality of the aggregates. The Barmac Rock On Rock Vertical Shaft Impactor proved that the shape of the aggregates can be improved by various crushing mechanisms as the EI and FI values were low and 75% of the cubical particles were observed in the crushed aggregates. (Author)

  16. Assessment of Rock Slope Stability in Limestone Quarries in the Tournai's Region (Belgium) Using Structural Data

    Science.gov (United States)

    Tshibangu, Jean-Pierre; Deloge, K. Pierre-Alexandre; Deschamps, Benoît; Coudyzer, Christophe

    The Tournais region is characterised by famous outcrops of carboniferous limestone which is mined out for cement and raw material production. The four main quarries found in the Region, i.e. Gaurain-Ramecroix, Milieu, Antoing and Lemay; are owned by the three main cement producers in Belgium: Italcimenti, Holcim and CBR. The global production of limestone is about 20 millions tons per year, giving big pits with depths up to 150 m. With the growth of the pits, the quarries are approaching each other leading to the problem of managing the reserves contained in the separating walls and their mechanical stability. The limestone deposit is composed of different seams having varying thickness, chemical com- position and even mechanical properties. The deposit has an overall horizontal dip and is intersected by two main sets of discontinuities with a spacing of about 10 m or less. It is also crossed by a set of east to west faults but the quarries are implanted in the in between areas, so to not be crossed by these faults. The layers and specially the shallow ones are characterised by a typical karstic weathering giving open or filled cavities. This paper presents the global work quarried out in order to study the stability of the Lemays quarry. First a description of the orientation and spacing of discontinuities is presented, and an attempt made to correlate to the development of weathering. Mechanical laboratory tests have been performed and a qualification of the rock mass assessed. A coupled approach is then presented using a mining planning analysis and mechanical simulation (i.e. Finite Element method).

  17. [Soil sandy desertification and salinization and their interrelationships in Yanghuang irrigated area of Hongsipu, Ningxia of northwest China].

    Science.gov (United States)

    Yang, Xin-guo; Song, Nai-ping

    2011-09-01

    By the methods of controlled and typical sampling, this paper analyzed the texture, salinization characteristics, cation exchange capacity (CEC), and their correlations in the 0-40 cm soil profiles of corn land, medlar land, and non-utilized land in Yanghuang irrigated area of Hongsipu, Northwest China. Under controlled sampling, the salt content in the soil profiles was 0.69-1.30 g x kg(-1) (except in non-utilized land where the 0-10 cm soil salt content was up to 1.74 g x kg(-1)), with no obvious salinization. The sodium adsorption ratio and exchangeable sodium percentage in the 20-40 cm soil layer of medlar land were 12.18 and 14.1%, respectively, and the total content of clay and silt in the 0-40 cm soil profile of medlar land was up to 37.3% whereas that in the 0-20 cm soil layer of corn land was only 13.5%. In the 20-40 cm soil layer of corn land, the indices of sandy desertification and salinization had significant correlations under controlled sampling but no correlations under typical sampling, while the CEC and the sandy desertification and salinization indices had significant correlations under typical sampling. In different land use types in the study area, soil sandy desertification and salinization had complicated interrelationships, and CEC could be used as the indicator for the changes in soil environmental quality.

  18. Evaluation of physical and mechanical properties of quarry stones in the southern Republic of Benin

    Directory of Open Access Journals (Sweden)

    Bouraima Mouhamed Bayane

    2017-05-01

    Full Text Available Engineering properties of stones have a crucial importance when they are used for civil engineering works. In this study, the suitability of rocks blocks or stones as a construction material is established. Cove and Dan cities surroundings in the southern part of Zou Province have large blocks and aggregates quarries operated recently. In this study, laboratory tests were carried out to investigate the performance of rocks blocks and aggregates quarried in the region. For this purpose of the study, three wooden containers with rocks blocks and aggregates samples were collected from three different quarries, and so, laboratory tests including particle density and water absorption test, resistance to wear, magnesium sulfate test, compressive strength and methylene blue absorption test were performed in accordance with the international standards to explore the quality of stones to be used for modern construction. Concluding that rocks blocks and aggregates satisfy the relevant regulation (that is, a norm, European standard.

  19. Factors affecting distribution of wood, detritus, and sediment in headwater streams draining managed young-growth red alder - Conifer forests in southeast Alaska

    Science.gov (United States)

    Gomi, T.; Johnson, A.C.; Deal, R.L.; Hennon, P.E.; Orlikowska, E.H.; Wipfli, M.S.

    2006-01-01

    Factors (riparian stand condition, management regimes, and channel properties) affecting distributions of wood, detritus (leaves and branches), and sediment were examined in headwater streams draining young-growth red alder (Alnus rubra Bong.) - conifer riparian forests (40 years old) remained in channels and provided sites for sediment and organic matter storage. Despite various alder-conifer mixtures and past harvesting effects, the abundance of large wood, fine wood, and detritus accumulations significantly decreased with increasing channel bank-full width (0.5-3.5 m) along relatively short channel distances (up to 700 m). Changes in wood, detritus, and sediment accumulations together with changes in riparian stand characteristics create spatial and temporal variability of in-channel conditions in headwater systems. A component of alder within young-growth riparian forests may benefit both wood production and biological recovery in disturbed headwater stream channels. ?? 2006 NRC.

  20. Quarry blasts assessment and their environmental impacts on the nearby oil pipelines, southeast of Helwan City, Egypt

    Directory of Open Access Journals (Sweden)

    Adel M.E. Mohamed

    2013-06-01

    Full Text Available Ground vibrations induced by blasting in the cement quarries are one of the fundamental problems in the quarrying industry and may cause severe damage to the nearby utilities and pipelines. Therefore, a vibration control study plays an important role in the minimization of environmental effects of blasting in quarries. The current paper presents the influence of the quarry blasts at the National Cement Company (NCC on the two oil pipelines of SUMED Company southeast of Helwan City, by measuring the ground vibrations in terms of Peak Particle Velocity (PPV. The seismic refraction for compressional waves deduced from the shallow seismic survey and the shear wave velocity obtained from the Multi channel Analysis of Surface Waves (MASW technique are used to evaluate the closest site of the two pipelines to the quarry blasts. The results demonstrate that, the closest site of the two pipelines is of class B, according to the National Earthquake Hazard Reduction Program (NEHRP classification and the safe distance to avoid any environmental effects is 650 m, following the deduced Peak Particle Velocity (PPV and scaled distance (SD relationship (PPV = 700.08 × SD−1.225 in mm/s and the Air over Pressure (air blast formula (air blast = 170.23 × SD−0.071 in dB. In the light of prediction analysis, the maximum allowable charge weight per delay was found to be 591 kg with damage criterion of 12.5 mm/s at the closest site of the SUMED pipelines.

  1. Isolation of Cryptococcus gattii molecular type VGIII, from Corymbia ficifolia detritus in Colombia.

    Science.gov (United States)

    Escandón, P; Sánchez, A; Firacative, C; Castañeda, E

    2010-06-01

    An environmental sampling survey was carried out in different areas of Bogotá, Colombia, to obtain isolates of members of the Cryptococcus neoformans/C. gattii species complex from Corymbia ficifolia trees. During a 6-month period in 2007, 128 samples consisting of bark, soil around trunk bases, detritus, seeds and flowers were collected from 91 trees and processed according to standard procedures. The molecular type was determined using URA5 restriction fragment length polymorphism (RFLP) analysis and the mating type was established by PCR using specific primers for Mfalpha and Mfa C. gattii was isolated from 15 of the 128 (11.7%) samples, of which three (20%) were recovered from the red flower extract and the remaining 12 from C. ficifolia detritus. URA5 RFLP analysis revealed that all 15 isolates belonged to the molecular type VGIII and mating type specific PCR revealed that all were mating type a. The isolation of C. gattii from C. ficifolia represents an important finding since this is the first report revealing C. ficifolia as a habitat for C. gattii and adds additional information to the ever growing spectrum of tree species from which C. gattii can be recovered.

  2. Strength Characteristics of Reinforced Sandy Soil

    OpenAIRE

    S. N. Bannikov; Mahamed Al Fayez

    2005-01-01

    Laboratory tests on determination of reinforced sandy soil strength characteristics (angle of internal friction, specific cohesive force) have been carried out with the help of a specially designed instrument and proposed methodology. Analysis of the obtained results has revealed that cohesive forces are brought about in reinforced sandy soil and an angle of internal soil friction becomes larger in comparison with non-reinforced soil.

  3. Mitigating the Health Risks of Stone Quarrying and Crushing in India ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    In Pratapura Industrial Area (Tikamgarh district, Bundelkhand region, Madhya ... In the context of weak regulatory enforcement, worksite health and safety ... in stone quarrying and crushing through better ecosystem management. ... India, Central Asia, Far East Asia, South Asia ... LVIF announces five more funded projects.

  4. Impact of Granite Quarrying on the Health of Workers and Nearby ...

    African Journals Online (AJOL)

    Choice-Academy

    assessed the residents' awareness of the negative implications of living in close ... residents of neighbouring communities are aware of risks associated with living near quarry ... plants, cement, refineries, petrol-chemicals and .... controlling indoor and outdoor air pollution, ... Plc, Associated Granite Industries, Fijabi Adebo.

  5. Landscape Visual Quality and Meiofauna Biodiversity on Sandy Beaches

    Science.gov (United States)

    Felix, Gabriela; Marenzi, Rosemeri C.; Polette, Marcos; Netto, Sérgio A.

    2016-10-01

    Sandy beaches are central economic assets, attracting more recreational users than other coastal ecosystems. However, urbanization and landscape modification can compromise both the functional integrity and the attractiveness of beach ecosystems. Our study aimed at investigating the relationship between sandy beach artificialization and the landscape perception by the users, and between sandy beach visual attractiveness and biodiversity. We conducted visual and biodiversity assessments of urbanized and semiurbanized sandy beaches in Brazil and Uruguay. We specifically examined meiofauna as an indicator of biodiversity. We hypothesized that urbanization of sandy beaches results in a higher number of landscape detractors that negatively affect user evaluation, and that lower-rated beach units support lower levels of biodiversity. We found that urbanized beach units were rated lower than semiurbanized units, indicating that visual quality was sensitive to human interventions. Our expectations regarding the relationship between landscape perception and biodiversity were only partially met; only few structural and functional descriptors of meiofauna assemblages differed among classes of visual quality. However, lower-rated beach units exhibited signs of lower environmental quality, indicated by higher oligochaete densities and significant differences in meiofauna structure. We conclude that managing sandy beaches needs to advance beyond assessment of aesthetic parameters to also include the structure and function of beach ecosystems. Use of such supporting tools for managing sandy beaches is particularly important in view of sea level rise and increasing coastal development.

  6. High resolution seismic tomography imaging of Ireland with quarry blast data

    Science.gov (United States)

    Arroucau, P.; Lebedev, S.; Bean, C. J.; Grannell, J.

    2017-12-01

    Local earthquake tomography is a well established tool to image geological structure at depth. That technique, however, is difficult to apply in slowly deforming regions, where local earthquakes are typically rare and of small magnitude, resulting in sparse data sampling. The natural earthquake seismicity of Ireland is very low. That due to quarry and mining blasts, on the other hand, is high and homogeneously distributed. As a consequence, and thanks to the dense and nearly uniform coverage achieved in the past ten years by temporary and permanent broadband seismological stations, the quarry blasts offer an alternative approach for high resolution seismic imaging of the crust and uppermost mantle beneath Ireland. We detected about 1,500 quarry blasts in Ireland and Northern Ireland between 2011 and 2014, for which we manually picked more than 15,000 P- and 20,000 S-wave first arrival times. The anthropogenic, explosive origin of those events was unambiguously assessed based on location, occurrence time and waveform characteristics. Here, we present a preliminary 3D tomographic model obtained from the inversion of 3,800 P-wave arrival times associated with a subset of 500 events observed in 2011, using FMTOMO tomographic code. Forward modeling is performed with the Fast Marching Method (FMM) and the inverse problem is solved iteratively using a gradient-based subspace inversion scheme after careful selection of damping and smoothing regularization parameters. The results illuminate the geological structure of Ireland from deposit to crustal scale in unprecedented detail, as demonstrated by sensitivity analysis, source relocation with the 3D velocity model and comparisons with surface geology.

  7. Reclamation of the Domtar/Canada brick quarry using coal fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, P J

    1991-03-20

    Two power plants in the Toronto area required disposal sites for coal fly ash in the late 1970s. A local brick quarry was recognized as a potential disposal site, since a 10-hectare area of the quarry was no longer in production and was required to be filled for reclamation. Ontario Hydro and the brick company joined together to obtain approval for the landfilling project. The preliminary site investigations included an examination of the impact of the project on local residents and the environment in terms of traffic volumes, noise levels, road dirt, airborne dust, and contamination of surface water and groundwater. Ontario Environmental Assessment Board hearings were held, with evidence presented from concerned parties. The findings from the hearings indicated that the project would have little effect on nearby residents and would improve the local environment by reclaiming usable land. Filling of the quarry began in December 1981 and continued for 5 years, after which a total of over 680,000 tonnes of fly ash was deposited. After completion, the ash was covered with a seal layer consisting of at least 1 m of clay or till compacted to structural fill standards with a 1 m thick protective cover layer to protect the seal layer from desiccation cracking and frost heave. Material is currently being stockpiled at the site to increase the thickness of the protective layer in order to make the site self-managing. Monitoring of surface water and groundwater is still ongoing and will continue for many years. 17 refs., 24 figs., 7 tabs.

  8. Source, habitat and nutrient enrichment effects on decomposition of detritus in Lower Mississippi River Basin bayous

    Science.gov (United States)

    Potential differences in storage and processing of detritus in agricultural landscapes may alter freshwater ecosystem function. We compared decomposition rates of maize (Zea mays) and willow oak (Quercus phellos) from three bayous located within the Lower Mississippi River Basin of NW Mississippi, ...

  9. Stratigraphic and structural compartmentalization observed within a model turbidite reservoir, Pennsylvanian Upper Jackfork Formation, Hollywood Quarry, Arkansas

    Energy Technology Data Exchange (ETDEWEB)

    Slatt, R. [Colorado School of Mines, Golden, CO (United States); Jordan, D. [Arco International Oil and Gas Co., Plano, TX (United States); Stone, C. [Arkansas Geological Commission, Little Rock, AR (United States)] [and others

    1995-08-01

    Hollywood Quarry is a 600 x 375 x 150 ft. (200 x 125 x 50m) excavation which provides a window into lower Pennsylvanian Jackfork Formation turbidite stratal architecture along the crest of a faulted anticlinal fold. A variety of turbidite facies are present, including: (a) lenticular, channelized sandstones, pebbly sandstones, and conglomerates within shale, (b) laterally continuous, interbedded thin sandstones and shales, and (c) thicker, laterally continuous shales. The sandstone and shale layers we broken by several strike-slip and reverse faults, with vertical displacements of up to several feet. This combination of facies and structural elements has resulted in a highly compartmentalized stratigraphic interval, both horizontally and vertically, along the anticlinal flexure. The quarry can be considered analogous to a scaled-down turbidite reservoir. Outcrop gamma-ray logs, measured sections, a fault map, and cross sections provide a database which is analogous to what would be available for a subsurface reservoir. Thus, the quarry provides an ideal outdoor geologic and engineering {open_quote}workshop{close_quote} venue for visualizing the potential complexities of a combination structural-stratigraphic (turbidite) reservoir. Since all forms of compartmentalization are readily visible in the quarry, problems related to management of compartmentalized reservoirs can be discussed and analyzed first-hand while standing in the quarry, within this {open_quote}model reservoir{close_quotes}. These problems include: (a) the high degree of stratigraphic and structural complexity that may be encountered, even at close well spacings, (b) uncertainty in well log correlations and log-shape interpretations, (c) variations in volumetric calculations as a function of amount of data available, and (d) potential production problems associated with specific {open_quote}field{close_quote} development plans.

  10. Mitigating the Health Risks of Stone Quarrying and Crushing in India ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    In Pratapura Industrial Area (Tikamgarh district, Bundelkhand region, Madhya Pradesh), stone quarrying and crushing is carried out by labor-intensive units employing unskilled workers on a seasonal basis complementing the agricultural cycle. In the context of weak regulatory enforcement, worksite health and safety ...

  11. Artificial sowing of endangered dry grassland species into disused basalt quarries

    Czech Academy of Sciences Publication Activity Database

    Novák, J.; Prach, Karel

    2010-01-01

    Roč. 205, č. 3 (2010), s. 179-183 ISSN 0367-2530 R&D Projects: GA AV ČR IAA600050702 Institutional research plan: CEZ:AV0Z60050516 Keywords : dry grasslands * seedling survival * quarries Subject RIV: EF - Botanics Impact factor: 1.657, year: 2010

  12. The effects of a perturbed source on contaminant transport near the Weldon Spring quarry

    International Nuclear Information System (INIS)

    Tomasko, D.

    1989-03-01

    The effects of a perturbed contamination source at the Weldon Spring quarry in St. Charles County, Missouri, on downstream solute concentrations were investigated using one-dimensional analytical solutions to an advection-dispersion equation developed for both constant-strength and multiple-stepped source functions. A sensitivity study using parameter base-case values and ranges consistent with the geologic conceptualization of the quarry area indicates that the parameters having the greatest effect on predicted concentrations are the distance from the quarry to the point of interest, the average linear groundwater velocity, the contaminant retardation coefficient, and the amplitude and duration of the source perturbation caused by response action activities. Use of base-case parameter value and realistic values for the amplitude and duration of the source perturbation produced a small effect on solute concentrations near the western extremity of the nearby municipal well field, as well as small uncertainties in the predicted results for the assumed model. The effect of simplifying assumptions made in deriving the analytic solution is unknown: use of a multidimensional flow and transport model and additional field work are needed to validate the model. 13 refs., 18 figs

  13. Feasibility study for remedial action for the Quarry Residuals Operable Unit at the Weldon Spring Site, Weldon Spring, Missouri

    International Nuclear Information System (INIS)

    1998-03-01

    The U.S. Department of Energy (DOE) is conducting cleanup activities at the Weldon Spring site, which is located in St. Charles County, Missouri, about 48 km (30 mi) west of St. Louis (Figure 1.1). Cleanup of the Weldon Spring site consists of several integrated components. The quarry residuals operable unit (QROU) is one of four operable units being evaluated. In accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended, a remedial investigation/feasibility study (RI/FS) is being conducted to evaluate conditions and potential responses for the following areas and/or media that constitute the QROU: (1) the residual material (soil and sediment) remaining at the Weldon Spring quarry after removal of the bulk waste (about 11 million L [3 million gal] of uranium-contaminated ponded water was also addressed previous to bulk waste removal); (2) other media located in the surrounding vicinity of the quarry, including adjacent soil, surface water, and sediment in Femme Osage Slough and several creeks; and (3) quarry groundwater located primarily north of Femme Osage Slough. Potential impacts to the St. Charles County well field downgradient of the quarry area are also being addressed as part of QROU RI/FS evaluations. For remedial action sites, it is DOE policy to integrate values associated with the National Environmental Policy Act (NEPA) into the CERCLA decision-making process. The analyses contained herein address NEPA values as appropriate to the actions being considered for the QROU. A work plan summarizing initial site conditions and providing conceptual site hydrogeological and exposure models was published in January 1994. The RI and baseline risk assessment (BRA) reports have been completed. The RI discusses in detail the nature and extent and the fate and transport of contamination at the quarry area

  14. Feasibility study for remedial action for the Quarry Residuals Operable Unit at the Weldon Spring Site, Weldon Spring, Missouri

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The U.S. Department of Energy (DOE) is conducting cleanup activities at the Weldon Spring site, which is located in St. Charles County, Missouri, about 48 km (30 mi) west of St. Louis (Figure 1.1). Cleanup of the Weldon Spring site consists of several integrated components. The quarry residuals operable unit (QROU) is one of four operable units being evaluated. In accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended, a remedial investigation/feasibility study (RI/FS) is being conducted to evaluate conditions and potential responses for the following areas and/or media that constitute the QROU: (1) the residual material (soil and sediment) remaining at the Weldon Spring quarry after removal of the bulk waste (about 11 million L [3 million gal] of uranium-contaminated ponded water was also addressed previous to bulk waste removal); (2) other media located in the surrounding vicinity of the quarry, including adjacent soil, surface water, and sediment in Femme Osage Slough and several creeks; and (3) quarry groundwater located primarily north of Femme Osage Slough. Potential impacts to the St. Charles County well field downgradient of the quarry area are also being addressed as part of QROU RI/FS evaluations. For remedial action sites, it is DOE policy to integrate values associated with the National Environmental Policy Act (NEPA) into the CERCLA decision-making process. The analyses contained herein address NEPA values as appropriate to the actions being considered for the QROU. A work plan summarizing initial site conditions and providing conceptual site hydrogeological and exposure models was published in January 1994. The RI and baseline risk assessment (BRA) reports have been completed. The RI discusses in detail the nature and extent and the fate and transport of contamination at the quarry area.

  15. Ground-water flow and ground- and surface-water interaction at the Weldon Spring quarry, St. Charles County, Missouri

    International Nuclear Information System (INIS)

    Imes, J.L.; Kleeschulte, M.J.

    1997-01-01

    Ground-water-level measurements to support remedial actions were made in 37 piezometers and 19 monitoring wells during a 19-month period to assess the potential for ground-water flow from an abandoned quarry to the nearby St. Charles County well field, which withdraws water from the base of the alluvial aquifer. From 1957 to 1966, low-level radioactive waste products from the Weldon Spring chemical plant were placed in the quarry a few hundred feet north of the Missouri River alluvial plain. Uranium-based contaminants subsequently were detected in alluvial ground water south of the quarry. During all but flood conditions, lateral ground-water flow in the bedrock from the quarry, as interpreted from water-table maps, generally is southwest toward Little Femme Osage Creek or south into the alluvial aquifer. After entering the alluvial aquifer, the ground water flows southeast to east toward a ground-water depression presumably produced by pumping at the St. Charles County well field. The depression position varies depending on the Missouri River stage and probably the number and location of active wells in the St. Charles County well field

  16. Einstein-Kubo-Helfand and McQuarrie relations for transport coefficients

    International Nuclear Information System (INIS)

    Erpenbeck, J.J.

    1995-01-01

    Monte Carlo molecular dynamics calculations of η E (C) (t;N) for an equimolar binary mixture of hard spheres (diameter ratio of 0.4 and mass ratio of 0.03) confirm these large differences at a few mean free times, but suggest a long-time plateau value having the magnitude of the Green-Kubo result, but the values at 70 mean free times do not approach η(t;N) with increasing N. Finally, we consider the one-particle, EKH-like, McQuarrie expression for shear viscosity, showing that the Chialvo-Cummings-Evans [Phys. Rev. E 47, 1702 (1993)] ''proof'' is defective. Moreover, we demonstrate through molecular dynamics calculations for the same hard-sphere mixture that the two-particle contribution to the time-dependent viscosity, which must vanish at long times for the McQuarrie formula to be valid, in fact contributes roughly 40% of the shear viscosity at a volume of (5 √2 /2)tsum a N a σ a 3 , where N a is the number of particles of species a having diameter σ a

  17. Computer Texture Mapping for Laser Texturing of Injection Mold

    Directory of Open Access Journals (Sweden)

    Yongquan Zhou

    2014-04-01

    Full Text Available Laser texturing is a relatively new multiprocess technique that has been used for machining 3D curved surfaces; it is more flexible and efficient to create decorative texture on 3D curved surfaces of injection molds so as to improve the surface quality and achieve cosmetic surface of molded plastic parts. In this paper, a novel method of laser texturing 3D curved surface based on 3-axis galvanometer scanning unit has been presented to prevent the texturing of injection mold surface from much distortion which is often caused by traditional texturing processes. The novel method has been based on the computer texture mapping technology which has been developed and presented. The developed texture mapping algorithm includes surface triangulation, notations, distortion measurement, control, and numerical method. An interface of computer texture mapping has been built to implement the algorithm of texture mapping approach to controlled distortion rate of 3D texture math model from 2D original texture applied to curvature surface. Through a case study of laser texturing of a high curvature surface of injection mold of a mice top case, it shows that the novel method of laser texturing meets the quality standard of laser texturing of injection mold.

  18. The ecology of sandy beaches in Natal

    African Journals Online (AJOL)

    The ecology of sandy beaches in Natal. A.H. Dye, A. Mclachlan and T. Wooldridge. Department of Zoology, University of Port Elizabeth, Port Elizabeth. Data from an ecological survey of four sandy beaches on the. Natal coast of South Africa are presented. Physical para· meters such as beach profile, particle size, moisture, ...

  19. Interaction of different irrigation strategies and soil textures on the nitrogen uptake of field grown potatoes

    DEFF Research Database (Denmark)

    Ahmadi, S.H.; Andersen, M.N.; Lærke, P.E.

    2011-01-01

    received 65% of FI after tuber bulking and lasted for six weeks until final harvest. Results showed that the irrigation treatments were not significantly different in terms of N uptake in the tubers, shoot, and whole crop. However, there was a statistical difference between the soil textures where plants...... in the loamy sand had the highest amount of N uptake. The interaction between irrigation treatments and soil textures was significant, and implied that under non-limiting water conditions, loamy sand is the suitable soil for potato production because plants can take up sufficient amounts of N and it could...... potentially lead to higher yield. However, under limited water conditions and applying water-saving irrigation strategies, sandy loam and coarse sand are better growth media because N is more available for the potatoes. The simple yield prediction model was developed that could explains ca. 96...

  20. Revegetation in abandoned quarries with landfill stabilized waste and gravels: water dynamics and plant growth - a case study

    Science.gov (United States)

    Zhang, Cheng-liang; Feng, Jing-jing; Rong, Li-ming; Zhao, Ting-ning

    2017-11-01

    Large amounts of quarry wastes are produced during quarrying. Though quarry wastes are commonly used in pavement construction and concrete production, in situ utilization during ecological restoration of abandoned quarries has the advantage of simplicity. In this paper, rock fragments 2-3 cm in size were mixed with landfill stabilized waste (LSW) in different proportions (LSW : gravel, RL), which was called LGM. The water content, runoff and plant growth under natural precipitation were monitored for 2 years using a runoff plot experiment. LGM with a low fraction of LSW was compacted to different degrees to achieve an appropriate porosity; water dynamics and plant growth of compacted LGM were studied in a field experiment. The results showed the following: (1) LGM can be used during restoration in abandoned quarries as growing material for plants. (2) RL had a significant effect on the infiltration and water-holding capacity of LGM and thus influenced the retention of precipitation, water condition and plant growth. LGM with RL ranging from 8:1 to 3:7 was suitable for plant growth, and the target species grew best when RL was 5:5. (3) Compaction significantly enhanced water content of LGM with a low RL of 2:8, but leaf water content of plants was lower or unchanged in the more compacted plots. Moderate compaction was beneficial to the survival and growth of Robinia pseudoacacia L. Platycladus orientalis (L.) Franco and Medicago sativa L. were not significantly affected by compaction, and they grew better under a high degree of compaction, which was disadvantageous for the uppermost layer of vegetation.

  1. Radiological and chemical characterization report for the planned Quarry Construction Staging Area and Water Treatment Plant: Revision 1

    International Nuclear Information System (INIS)

    1989-03-01

    The Quarry Construction Staging Area and Water Treatment Plant (QCSA) will be used in the support of the bulk waste removal of the Weldon Spring Quarry. Radiological and chemical characterization was performed on a 12 acre site where the QCSA will be constructed. The characterization revealed approximately .5 acres of radiologically contaminated land. No chemical contamination was found. 8 refs., 5 figs., 7 tabs

  2. Bibliography of sandy beaches and sandy beach organisms on the African continent

    CSIR Research Space (South Africa)

    Bally, R

    1986-01-01

    Full Text Available This bibliography covers the literature relating to sandy beaches on the African continent and outlying islands. The bibliography lists biological, chemical, geographical and geological references and covers shallow marine sediments, surf zones off...

  3. Mitigating the Health Risks of Stone Quarrying and Crushing in India ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Safety and health in the stone crushing industry : a practical manual for preventing accidents preserving health and keeping a company profitable. Études. Abstract for oral presentation : addressing health risk of communities residing close to stone quarrying and crushing unit using ecohealth framework in Central India.

  4. A Method of Effective Quarry Water Purifying Using Artificial Filtering Arrays

    Science.gov (United States)

    Tyulenev, M.; Garina, E.; Khoreshok, A.; Litvin, O.; Litvin, Y.; Maliukhina, E.

    2017-01-01

    The development of open pit mining in the large coal basins of Russia and other countries increases their negative impact on the environment. Along with the damage of land and air pollution by dust and combustion gases of blasting, coal pits have a significant negative impact on water resources. Polluted quarry water worsens the ecological situation on a much larger area than covered by air pollution and land damage. This significantly worsens the conditions of people living in cities and towns located near the coal pits, and complicates the subsequent restoration of the environment, irreversibly destroying the nature. Therefore, the research of quarry wastewater purifying is becoming an important mater for scholars of technical colleges and universities in the regions with developing open-pit mining. This paper describes the method of determining the basic parameters of the artificial filtering arrays formed on coal pits of Kuzbass (Western Siberia, Russia), and gives recommendations on its application.

  5. Environmental evaluation of the air in a quarry in complex land

    International Nuclear Information System (INIS)

    Bedoya V, Julian

    1999-01-01

    Wind motion in a mountain terrain is hard to model, especially if it is located in the dividing line of the mountain where different wind regimes meet. In addition to difficulties in assessing wind fields, air pollution modeling requires special handling of receptors to estimate pollutant concentration (basically total suspended particulate for the case of a quarry). Modeling procedures are explained based on an exceptionally complex application for a quarry located in a mountain gorge in an eastern Colombian mountain. Emission factors of the US Environmental Protection Agency were applied to this example and the information was processed to use the ISCLT (Industrial Source Complex Long Term) dispersion model. Required meteorological information was obtained by interpolation of wind roses recorded in the two sides of the mountain (Santa fe de Bogota and Villavicencio). Two scenarios were modeled generating satisfying results since the highest air quality impacts are inside property line where occupational hygiene is applied

  6. Ion-beam texturing of uniaxially textured Ni films

    International Nuclear Information System (INIS)

    Park, S.J.; Norton, D.P.; Selvamanickam, Venkat

    2005-01-01

    The formation of biaxial texture in uniaxially textured Ni thin films via Ar-ion irradiation is reported. The ion-beam irradiation was not simultaneous with deposition. Instead, the ion beam irradiates the uniaxially textured film surface with no impinging deposition flux, which differs from conventional ion-beam-assisted deposition. The uniaxial texture is established via a nonion beam process, with the in-plane texture imposed on the uniaxial film via ion beam bombardment. Within this sequential ion beam texturing method, grain alignment is driven by selective etching and grain overgrowth

  7. Measurements of seismic vibrations induced by Quarry blasts at the Mostecká basin

    Czech Academy of Sciences Publication Activity Database

    Kaláb, Zdeněk

    -, č. 271 (2006), s. 49-58 ISSN 0372-9508 Institutional research plan: CEZ:AV0Z30860518 Keywords : seismic vibration * slope stability * quarry blast Subject RIV: DC - Siesmology, Volcanology, Earth Structure

  8. Model projections of atmospheric steering of Sandy-like superstorms.

    Science.gov (United States)

    Barnes, Elizabeth A; Polvani, Lorenzo M; Sobel, Adam H

    2013-09-17

    Superstorm Sandy ravaged the eastern seaboard of the United States, costing a great number of lives and billions of dollars in damage. Whether events like Sandy will become more frequent as anthropogenic greenhouse gases continue to increase remains an open and complex question. Here we consider whether the persistent large-scale atmospheric patterns that steered Sandy onto the coast will become more frequent in the coming decades. Using the Coupled Model Intercomparison Project, phase 5 multimodel ensemble, we demonstrate that climate models consistently project a decrease in the frequency and persistence of the westward flow that led to Sandy's unprecedented track, implying that future atmospheric conditions are less likely than at present to propel storms westward into the coast.

  9. Inter-annual changes in detritus-based food chains can enhance plant growth response to elevated atmospheric CO2.

    Science.gov (United States)

    Hines, Jes; Eisenhauer, Nico; Drake, Bert G

    2015-12-01

    Elevated atmospheric CO2 generally enhances plant growth, but the magnitude of the effects depend, in part, on nutrient availability and plant photosynthetic pathway. Due to their pivotal role in nutrient cycling, changes in abundance of detritivores could influence the effects of elevated atmospheric CO2 on essential ecosystem processes, such as decomposition and primary production. We conducted a field survey and a microcosm experiment to test the influence of changes in detritus-based food chains on litter mass loss and plant growth response to elevated atmospheric CO2 using two wetland plants: a C3 sedge (Scirpus olneyi) and a C4 grass (Spartina patens). Our field study revealed that organism's sensitivity to climate increased with trophic level resulting in strong inter-annual variation in detritus-based food chain length. Our microcosm experiment demonstrated that increased detritivore abundance could not only enhance decomposition rates, but also enhance plant growth of S. olneyi in elevated atmospheric CO2 conditions. In contrast, we found no evidence that changes in the detritus-based food chains influenced the growth of S. patens. Considered together, these results emphasize the importance of approaches that unite traditionally subdivided food web compartments and plant physiological processes to understand inter-annual variation in plant production response to elevated atmospheric CO2. © 2015 John Wiley & Sons Ltd.

  10. Reservoir architecture patterns of sandy gravel braided distributary channel

    Directory of Open Access Journals (Sweden)

    Senlin Yin

    2016-06-01

    Full Text Available The purpose of this study was to discuss shape, scale and superimposed types of sandy gravel bodies in sandy-gravel braided distributary channel. Lithofacies analysis, hierarchy bounding surface analysis and subsurface dense well pattern combining with outcrops method were used to examine reservoir architecture patterns of sandy gravel braided distributary channel based on cores, well logging, and outcrops data, and the reservoir architecture patterns of sandy gravel braided distributary channels in different grades have been established. The study shows: (1 The main reservoir architecture elements for sandy gravel braided channel delta are distributary channel and overbank sand, while reservoir flow barrier elements are interchannel and lacustrine mudstone. (2 The compound sand bodies in the sandy gravel braided delta distributary channel take on three shapes: sheet-like distributary channel sand body, interweave strip distributary channel sand body, single strip distributary channel sand body. (3 Identification marks of single distributary channel include: elevation of sand body top, lateral overlaying, “thick-thin-thick” feature of sand bodies, interchannel mudstone and overbank sand between distributary channels and the differences in well log curve shape of sand bodies. (4 Nine lithofacies types were distinguished in distributary channel unit interior, different channel units have different lithofacies association sequence.

  11. Mitigating the Health Risks of Stone Quarrying and Crushing in India ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    In Pratapura Industrial Area (Tikamgarh district, Bundelkhand region, Madhya ... In the context of weak regulatory enforcement, worksite health and safety measures are not ... involved in stone quarrying and crushing through better ecosystem management. ... et les défis futurs dans la communauté économique de l'ASEAN.

  12. Geology of the Carnegie museum dinosaur quarry site of Diplodocus carnegii, Sheep Creek, Wyoming

    Science.gov (United States)

    Brezinski, D.K.; Kollar, A.D.

    2008-01-01

    The holotype of Diplodocus carnegii Hatcher, 1901, consists of a partial skeleton (CM 84) that was recovered, along with a second partial skeleton of the same species (CM 94), from the upper 10 m of the Talking Rock facies of the Brushy Basin Member of the Morrison Formation exposed along Bone Quarry Draw, a tributary of Sheep Creek in Albany County, Wyoming. A composite measured section of the stratigraphic interval exposed adjacent to the quarry indicates that the Brushy Basin Member in this area is a stacked succession of lithofacies consisting of hackly, greenish gray, calcareous mudstone and greenish brown, dense, fine-grained limestone. The more erosion resistant limestone layers can be traced over many hundreds of meters. Thus, these strata do not appear to represent a highly localized deposit such as a stream channel, oxbow lake, or backwater pond. The Sheep Creek succession is interpreted as representing a clastic-dominated lake where high turbidity and sediment influx produced deposition of calcareous mudstone. During drier periods the lake's turbidity decreased and limestone and dolomite precipitation replaced mud deposition. Microkarsting at the top of some limestone/ dolomite layers suggests subaerial deposition may have prevailed during these dry episodes. The quarry of D. carnegii was excavated within the top strata of one of the numerous intervals of hackly, greenish gray, calcareous mudstone that represent an ephemeral freshwater lake. The quarry strata are directly overlain by 0.3 m of dolomite-capped limestone that was deposited shortly after interment of D. carnegii in the lake mudstones. The close vertical proximity of the overlying limestone to the skeleton's stratigraphic: level suggests that the animal's carcass may have been buried beneath the drying lake deposits during a period of decreased rainfall.

  13. Content Analysis of Select YouTube Postings: Comparisons of Reactions to the Sandy Hook and Aurora Shootings and Hurricane Sandy.

    Science.gov (United States)

    Miller, Eric D

    2015-11-01

    This study details an innovative and methodical content analysis of 2,207 YouTube comments from four different YouTube videos (e.g., breaking news or memorials) related to the 2012 Sandy Hook Elementary School and Aurora theater mass shootings and the catastrophic Hurricane Sandy. As expected, YouTube comments associated with the Sandy Hook shootings (particularly those from a memorial video) were especially likely to feature compassion and grief with lessened hostility. This study highlights differing online contexts by which individuals show grief and related emotions following man-made and natural calamities and how-even in an online environment-powerful situational contexts greatly guide behavior.

  14. Chrysotile asbestos quantification in serpentinite quarries: a case study in Valmalenco, central Alps, northern Italy

    Science.gov (United States)

    Cavallo, Alessandro

    2013-04-01

    Outcrops of serpentinites are usually strongly fractured and cataclastic, and the rock can only be used as ballast. However, in rare cases, like in Valmalenco (Central Alps, Northern Italy), fractures are regular and well spaced, and the rock mass has good geotechnical quality, ideal conditions for the extraction of dimension stone blocks. The Valmalenco Serpentinite is marketed worldwide as dimension and decorative stone, with remarkable mechanical properties and pleasing colours and textures. However, the same area was once subject to chrysotile asbestos mining, in the form of discrete veins along the main discontinuities of the rock mass. For this reason, airborne asbestos contamination can occur during the extraction and processing cycle of the rocks, therefore it is essential to locate and quantify asbestos in the rock mass, to reduce as much as possible the exposure risk. The first step was a detailed geostructural survey of each quarry, in order to characterize the main discontinuities (orientation, spacing, linear persistence, opening, filling), with special attention to the identification of fibrous minerals. The surveys was followed by extensive sampling of massive rocks, mineralized veins and fillings of fractures, and the cutting sludge derived from diamond wire cutting. Preliminary qualitative XRPD was performed on all samples, while quantitative analysis was carried out on the most representative samples of the main rock mass discontinuities. On the other hand, XRPD is not effective in the identification of asbestos percentages of less than 2% by weight, and the accurate distinction among the various serpentine polymorphs (antigorite, lizardite, chrysotile) is very difficult (if not impossible) when they are simultaneously present, due to their very similar basic structure and the strong structural disorder. The same samples were then analyzed by SEM-EDS (fiber counting after filtration on a polycarbonate filter), for a better distinction between

  15. Science and Sandy: Lessons Learned

    Science.gov (United States)

    Werner, K.

    2013-12-01

    Following Hurricane Sandy's impact on the mid-Atlantic region, President Obama established a Task Force to '...ensure that the Federal Government continues to provide appropriate resources to support affected State, local, and tribal communities to improve the region's resilience, health, and prosperity by building for the future.' The author was detailed from NOAA to the Task Force between January and June 2013. As the Task Force and others began to take stock of the region's needs and develop plans to address them, many diverse approaches emerged from different areas of expertise including: infrastructure, management and construction, housing, public health, and others. Decision making in this environment was complex with many interests and variables to consider and balance. Although often relevant, science and technical expertise was not always at the forefront of this process. This talk describes the author's experience with the Sandy Task Force focusing on organizing scientific expertise to support the work of the Task Force. This includes a description of federal activity supporting Sandy recovery efforts, the role of the Task Force, and lessons learned from developing a science support function within the Task Force.

  16. Ultimate Owner and Firm Performance - Evidence from Romanian Mining and Quarrying Listed Firms

    Directory of Open Access Journals (Sweden)

    Cosmin MIHAI

    2012-08-01

    Full Text Available The main objectives of this paper are to describe the necessary steps to identify the ultimate owner and to investigate the relation between the ultimate ownership and the financial performance of Romanian mining and quarrying listed firms. The study was conducted for the companies listed on Bucharest Stock Exchange, in both regulated and non-regulated segments. The final sample included 17 companies of mining and quarrying. Return on Equity was used for measuring the financial performance of the firms. The ultimate ownership was measured by the percentage of voting rights held by a shareholder. Econometric tools like multiple linear regression analysis were used for analysis. The results of the study suggest that there is a significant negative link between financial performance and divergence between voting rights and cash-flow rights.

  17. The response of macroinvertebrates to artificially enhanced detritus levels in plantation streams

    Science.gov (United States)

    Pretty, J. L.; Dobson, M.

    The leaves and wood from vegetation surrounding headwater streams constitute a major food source for aquatic invertebrates, providing they are retained upon the streambed and not transported downstream. This study investigated the response of aquatic invertebrates to artificially increased detritus retention, in an effort to reproduce the naturally occurring build up of dead organic matter associated with streams in old-growth forest. The background detrital standing stock in streams in Kielder Forest (Northumberland, UK) was low, approximately 32 gm-2. Two streams flowing through dense conifer plantation and one in open broadleaved woodland were manipulated by the addition of logs over a 10 m stream reach. After several months, log addition significantly enhanced detrital standing stocks in both conifer and broadleaved streams. Total invertebrate abundance, taxon richness and the numbers of certain numerically dominant families were significantly higher in experimental than reference reaches in both conifer and broadleaved streams. This response was most marked for detritivores, whilst non-detritivore groups often showed no response to the manipulation. Whilst in the short term the responses to enhanced retention may reflect a redistribution of the local fauna, it is argued that over a longer time-scale, a genuine increase in invertebrate density and diversity could occur. Allowing old-growth forest to develop in planted valley bottoms may be a viable management option for conservation. If established alongside streams, it would ensure continuous input of woody material and the fauna may benefit from the resulting increase in detritus retention.

  18. Asbestos exposure during quarrying and processing of serpentinites: a case study in Valmalenco, Central Alps, Northern Italy

    Science.gov (United States)

    Cavallo, A.; Rimoldi, B.

    2012-04-01

    Serpentinites are metamorphic rocks derived from ultramafics such as peridotites (lherzolites and/or harzburgites), with a typical mineralogical assemblage of antigorite, olivine, diopside and minor magnetite, chlorite and chrysotile. If the rock mass has good geotechnical properties, these stones are quarried because of their wide variety of green shades and outstanding technical properties. Excellent stones are produced in the Malenco Valley, Central Alps (northern Italy, Sondrio): here the geological set-up is dominated by the ultramafic Malenco massif (lower crust-mantle complex), exposed at the Penninic to Austroalpine boundary zone. Different processing operations give origin to valuable products like stoves, funeral monuments, design home appliances; important building element as roof slabs, tiles for floor and wall coverings constitute the main commercial line of production. In this area, good quality long fibre chrysotile asbestos was mined since the XIX century, till the seventies. The asbestos fissures (mostly slip-fiber) are well known in Valmalenco, associated to an important ENE-WSW striking fracture and hydrothermal vein system. Some actual serpentinite quarries "cross" at times tunnels of the old asbestos mines, because the fracture and vein system "guides" the extraction. At present time, this area represents an excellent example of naturally occurring asbestos (NOA). For these reasons, workers' exposure to asbestos during quarrying and processing cannot be ruled out, and must be assessed according to national laws. From 2004 to nowadays, the INAIL Regional Management of Lombardia, with the collaboration of University of Milan-Bicocca, carried out extensive monitoring campaigns both in quarries and in processing laboratories. More than 300 massive samples (rocks and veins) and 250 airborne dust samples were collected during the surveys. One of the main problems in the study of massive serpentinites is the accurate identification of the different

  19. The role of risk assessment in project planning at the Weldon Spring Quarry, Weldon Spring, Missouri

    International Nuclear Information System (INIS)

    Haroun, L.A.; Peterson, J.M.

    1989-01-01

    This paper presents the methodology used to prepare a baseline risk evaluation of the bulk wastes at the quarry. The DOE is proposing to remove these bulk wastes and transport them approximately 6.4 km (4 mi) to a temporary storage facility at the chemical plant area of the Weldon Spring site. The DOE has responsibility for cleanup activities at the Weldon Spring site under its Surplus Facilities Management Program (SFMP). A baseline risk evaluation is an evaluation of the potential impacts on human health and the environment that may result from exposure to releases of contaminants from a site in the absence of site remediation. This evaluation is a key component of the remedial investigation (RI) process, as identified in guidance from the US Environmental Protection Agency (EPA) that addresses sites subject to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) of 1980, as amended by the Superfund Amendments and Reauthorization Act of 1986. Response actions at the Weldon Spring quarry are subject to CERCLA requirements because the quarry is listed on the EPA's National Priorities List

  20. Work plan for the remedial investigation/feasibility study-environmental assessment for the quarry residuals operable unit at the Weldon Spring Site

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    The US Department of Energy (DOE) is conducting cleanup activities at the Weldon Spring site, which is located in St. Charles County, Missouri, about 48 km (30 mi) west of St. Louis. The Weldon Spring site consists of two noncontiguous areas -- the chemical plant area, which includes four raffinate pits, and the quarry. Cleanup activities at the Weldon Spring site are conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended, incorporating the values of the National Environmental Policy Act (NEPA). The contents of the documents prepared for the project are not intended to represent a statement regarding the legal applicability of NEPA to remedial actions conducted under CERCLA. In accordance with the integrated CERCLA/NEPA approach, a remedial investigation/feasibility study-environmental assessment (RI/FS-EA) is being conducted to evaluate conditions and potential responses for the quarry residuals operable unit (QROU). This operable unit consists of the following areas and/or media: the residual material remaining at the Weldon Spring quarry after removal of the pond water and bulk waste; underlying groundwater; and other media located in the surrounding vicinity of the quarry, including adjacent soil, surface water, and sediment in Femme Osage Slough. This work plan identifies the activities within the RI/FS-EA process that are being proposed to address contamination remaining at the quarry area.

  1. Work plan for the remedial investigation/feasibility study-environmental assessment for the quarry residuals operable unit at the Weldon Spring Site

    International Nuclear Information System (INIS)

    1994-01-01

    The US Department of Energy (DOE) is conducting cleanup activities at the Weldon Spring site, which is located in St. Charles County, Missouri, about 48 km (30 mi) west of St. Louis. The Weldon Spring site consists of two noncontiguous areas -- the chemical plant area, which includes four raffinate pits, and the quarry. Cleanup activities at the Weldon Spring site are conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended, incorporating the values of the National Environmental Policy Act (NEPA). The contents of the documents prepared for the project are not intended to represent a statement regarding the legal applicability of NEPA to remedial actions conducted under CERCLA. In accordance with the integrated CERCLA/NEPA approach, a remedial investigation/feasibility study-environmental assessment (RI/FS-EA) is being conducted to evaluate conditions and potential responses for the quarry residuals operable unit (QROU). This operable unit consists of the following areas and/or media: the residual material remaining at the Weldon Spring quarry after removal of the pond water and bulk waste; underlying groundwater; and other media located in the surrounding vicinity of the quarry, including adjacent soil, surface water, and sediment in Femme Osage Slough. This work plan identifies the activities within the RI/FS-EA process that are being proposed to address contamination remaining at the quarry area

  2. Effects of soil amendment on soil characteristics and maize yield in Horqin Sandy Land

    Science.gov (United States)

    Zhou, L.; Liu, J. H.; Zhao, B. P.; Xue, A.; Hao, G. C.

    2016-08-01

    A 4-year experiment was conducted to investigate the inter-annual effects of sandy soil amendment on maize yield, soil water storage and soil enzymatic activities in sandy soil in Northeast China in 2010 to 2014. We applied the sandy soil amendment in different year, and investigated the different effects of sandy soil amendment in 2014. There were six treatments including: (1) no sandy soil amendment application (CK); (2) one year after applying sandy soil amendment (T1); (3) two years after applying sandy soil amendment(T2); (4) three years after applying sandy soil amendment(T3); (5)four years after applying sandy soil amendment(T4); (6) five years after applying sandy soil amendment (T5). T refers to treatment, and the number refers to the year after application of the sandy soil amendment. Comparing with CK, sandy soil amendments improved the soil water storage, soil urease, invertase, and catalase activity in different growth stages and soil layers, the order of soil water storage in all treatments roughly performed: T3 > T5 > T4 > T2 > T1 > CK. the order of soil urease, invertase, and catalase activity in all treatments roughly performed: T5 > T3 > T4 > T2 > T1 > CK. Soil application of sandy soil amendment significantly (p≤⃒0.05) increased the grain yield and biomass yield by 22.75%-41.42% and 29.92%-45.45% respectively, and maize yield gradually increased with the years go by in the following five years. Sandy soil amendment used in poor sandy soil had a positive effect on soil water storage, soil enzymatic activities and maize yield, after five years applied sandy soil amendment (T5) showed the best effects among all the treatments, and deserves further research.

  3. Effect of quarrying activity on biodiversity: Case study of Ogbere site ...

    African Journals Online (AJOL)

    USER

    Musa spp. was significant. The Diversity Index ranged from1.6 to 2.2 while the Equitability or Evenness .... habitat requirement of the species concerned (Homer et al. 1993). ... the advantage of the vast adjacent farm land to the unexploited site that .... Table 3. Bird population density at the quarry site in Ogbere village. Taxon.

  4. Seismic scattering attribute for sedimentary classification of nearshore marine quarries for a major beach nourishment project: Case study of Adriatic coastline, Regione Abruzzo (Italy)

    Science.gov (United States)

    Orlando, Luciana; Contini, Paolo; De Girolamo, Paolo

    2017-06-01

    Of fundamental importance for any major beach nourishment project using marine quarries is a correct sedimentary classification. The main purpose of such a classification is to identify sand with the appropriate features for beach nourishment. This task is more onerous when quarry sediments are heterogeneous and mixed with silt. This is typical of nearshore marine quarries. The presence of excess silt compromises the use of marine quarries because of the water turbidity that may be induced in the nourished beaches, especially when the beaches are protected by defense structures. Here we discuss the use of scattering amplitude of seismic data, acquired with a pinger source (2-10 kHz), to detect and classify the unconsolidated sediment of a marine quarry. A robust correlation was found between this seismic attribute and the silt content in the sediment. The scattering amplitude was numerically calculated from the seismic data and used to map slices of silt content at different depths. The results have been validated with sedimentary analysis of vibra- and rotary cores, and by the dredged material used for the beach nourishment. The marine quarry produced about 1.200.000 m3 of sand used to nourish eight different beach sites along the Adriatic coasts of the Regione Abruzzo (Italy). The large-scale sedimentary assessment of the area was based on seismic boomer data and the evaluation of the volume of dredged sediments on multibeam data surveyed before and after the exploitation of the quarry. The study shows that this approach is effective in sites with high lateral and vertical variations in the percentage of sand in the sediments.

  5. Groundwater monitoring of an open-pit limestone quarry: groundwater characteristics, evolution and their connections to rock slopes.

    Science.gov (United States)

    Eang, Khy Eam; Igarashi, Toshifumi; Fujinaga, Ryota; Kondo, Megumi; Tabelin, Carlito Baltazar

    2018-03-06

    Groundwater flow and its geochemical evolution in mines are important not only in the study of contaminant migration but also in the effective planning of excavation. The effects of groundwater on the stability of rock slopes and other mine constructions especially in limestone quarries are crucial because calcite, the major mineral component of limestone, is moderately soluble in water. In this study, evolution of groundwater in a limestone quarry located in Chichibu city was monitored to understand the geochemical processes occurring within the rock strata of the quarry and changes in the chemistry of groundwater, which suggests zones of deformations that may affect the stability of rock slopes. There are three distinct geological formations in the quarry: limestone layer, interbedded layer of limestone and slaty greenstone, and slaty greenstone layer as basement rock. Although the hydrochemical facies of all groundwater samples were Ca-HCO 3 type water, changes in the geochemical properties of groundwater from the three geological formations were observed. In particular, significant changes in the chemical properties of several groundwater samples along the interbedded layer were observed, which could be attributed to the mixing of groundwater from the limestone and slaty greenstone layers. On the rainy day, the concentrations of Ca 2+ and HCO 3 - in the groundwater fluctuated notably, and the groundwater flowing along the interbedded layer was dominated by groundwater from the limestone layer. These suggest that groundwater along the interbedded layer may affect the stability of rock slopes.

  6. Szczercow quarry a chance of Polish electrical power industry

    International Nuclear Information System (INIS)

    Koziol, K.

    1994-01-01

    The brown coal deposits near Belchatow (Central Poland) are described. One of them Belchatow is exploited for the needs of Belchatow 1 Power Plant (12 x 360 MW). The second Szczercow is the unfinished investment. The quarry Szczercow was designed as a source of fuel for Belchatow 1 as well as Belchatow 2 Power Plant (6 x 370 MW). The present state of the investment is described and serious arguments for its continuation are given. 1 ill., 1 plan

  7. Superfund Record of Decision (EPA Region 7): Weldon Spring Quarry/Plant/Pits (USDOE), Weldon Spring, MO. (Second remedial action), September 1990

    International Nuclear Information System (INIS)

    1990-01-01

    The 226-acre Weldon Spring Quarry/Plant/Pits (USDOE) site is a former ordnance works and chemical plant near the city of Weldon Spring in St. Charles County, Missouri. The site is divided into two noncontiguous areas: a 217-acre chemical plant area, comprised of various buildings, ponds and four raffinate pits, and a 9-acre quarry, which forms a valley wall at the edge of the Missouri River floodplain. Since the early 1940s, the site has been used by various government agencies for chemical and ordnance processing with chemical and radioactive waste disposal in the quarry. From 1941 to 1946, the site was an Army ordnance works used for the production of trinitrotoluene (TNT) and dinitrotoluene (DNT) explosives. The selected interim remedial action for the site includes excavating an estimated 95,000 cubic yards of chemically and radioactively contaminated bulk wastes from the quarry and temporarily storing the wastes onsite in the chemical plant area; and implementing site access restrictions. The estimated total cost for the remedial action is $11,000,000

  8. Revegetation in abandoned quarries with landfill stabilized waste and gravels: water dynamics and plant growth – a case study

    Directory of Open Access Journals (Sweden)

    C.-L. Zhang

    2017-11-01

    Full Text Available Large amounts of quarry wastes are produced during quarrying. Though quarry wastes are commonly used in pavement construction and concrete production, in situ utilization during ecological restoration of abandoned quarries has the advantage of simplicity. In this paper, rock fragments 2–3 cm in size were mixed with landfill stabilized waste (LSW in different proportions (LSW : gravel, RL, which was called LGM. The water content, runoff and plant growth under natural precipitation were monitored for 2 years using a runoff plot experiment. LGM with a low fraction of LSW was compacted to different degrees to achieve an appropriate porosity; water dynamics and plant growth of compacted LGM were studied in a field experiment. The results showed the following: (1 LGM can be used during restoration in abandoned quarries as growing material for plants. (2 RL had a significant effect on the infiltration and water-holding capacity of LGM and thus influenced the retention of precipitation, water condition and plant growth. LGM with RL ranging from 8:1 to 3:7 was suitable for plant growth, and the target species grew best when RL was 5:5. (3 Compaction significantly enhanced water content of LGM with a low RL of 2:8, but leaf water content of plants was lower or unchanged in the more compacted plots. Moderate compaction was beneficial to the survival and growth of Robinia pseudoacacia L. Platycladus orientalis (L. Franco and Medicago sativa L. were not significantly affected by compaction, and they grew better under a high degree of compaction, which was disadvantageous for the uppermost layer of vegetation.

  9. 1D resistivity inversion technique in the mapping of igneous intrusives; A step to sustainable quarry development

    Directory of Open Access Journals (Sweden)

    M.A. Nwachukwu

    2017-01-01

    Full Text Available The use of trial pits as a first step in quarry site development causes land degradation and results in more failure than success for potential quarry investors in some parts of the world. In this paper, resistivity, depth and distance values derived from 26 Vertical Electric Soundings (VES and 2 profiling inversion sections were successfully used to evaluate a quarry site prior to development. The target rock Diabase (Dolerite was observed and it had a resistivity range of 3.0 × 104 –7. 8 × 106 Ω-m, and was clearly distinguishable from associated rocks with its bright red color code on the AGI 1D inversion software. This target rock was overlain by quartzite, indurate shale and mudstone as overburden materials. The quartzite, with its off-red colour, has a resistivity range of 2.0 × 103–2.9 × 105 Ω-m, while the indurate shale, with a yellowish-brown colour, showed resistivity values ranging from 6.1 × 102 – 2.8 × 105 Ω-m. Topsoil was clayey, with a resistivity range from 8 – 8.6 × 102u Ω-m and depths of 0.3–1.8 m, often weathered and replaced by associated rocks outcrops. The diabase rock, in the three prospective pits mapped, showed thicknesses of between 40 and 76 m across the site. The prospective pits were identified to accommodate an estimated 2,569,450 tonnes of diabase with an average quarry pit depth of 50 m. This figure was justified by physical observations made at a nearby quarry pit and from test holes. Communities were able to prepare a geophysical appraisal of the intrusive body in their domain for economic planning and sustainability of the natural resource.

  10. Specification aggregate quarry expansion: a case study demonstrating sustainable management of natural aggregate resources

    Science.gov (United States)

    Langer, William H.; Tucker, M.L.

    2003-01-01

    Many countries, provinces, territories, or states in the European Union, Australia, Canada, the United States, and elsewhere have begun implementing sustainability programs, but most of those programs stop short of sustainable management of aggregate resources. Sustainable practices do not always have to be conducted under the title of sustainability. This case study describes how Lafarge, a large multinational construction materials supplier, implemented the principles of sustainability even though there was an absence of existing local government policies or procedures addressing sustainable resource management. Jefferson County, Colorado, USA, is one of three counties in the six-county Denver, Colorado, region that has potentially available sources of crushed stone. Crushed stone comprises 30 percent of the aggregate produced in the area and plays a major role in regional aggregate resource needs. Jefferson County is home to four of the five crushed stone operations in the Denver region. Lafarge operates one of those four quarries. Lafarge recently proposed to expand its reserves by exchanging company-owned land for existing dedicated open space land adjacent to their quarry but owned by Jefferson County. A similar proposal submitted about 10 years earlier had been denied. Contrary to the earlier proposal, which was predicated on public relations, the new proposal was predicated on public trust. Although not explicitly managed under the moniker of sustainability, Lafarge used basic management principles that embody the tenets of sustainability. To achieve the goals of sustainable aggregate management where no governmental policies existed, Lafarge not only assumed their role of being a responsible corporate and environmental member of the community, but also assumed the role of facilitator to encourage and enable other stakeholders to responsibly resolve legitimate concerns regarding the Lafarge quarry proposal. Lafarge successfully presented an enlightened

  11. Block volume estimation from the discontinuity spacing measurements of mesozoic limestone quarries, Karaburun Peninsula, Turkey.

    Science.gov (United States)

    Elci, Hakan; Turk, Necdet

    2014-01-01

    Block volumes are generally estimated by analyzing the discontinuity spacing measurements obtained either from the scan lines placed over the rock exposures or the borehole cores. Discontinuity spacing measurements made at the Mesozoic limestone quarries in Karaburun Peninsula were used to estimate the average block volumes that could be produced from them using the suggested methods in the literature. The Block Quality Designation (BQD) ratio method proposed by the authors has been found to have given in the same order of the rock block volume to the volumetric joint count (J(v)) method. Moreover, dimensions of the 2378 blocks produced between the years of 2009 and 2011 in the working quarries have been recorded. Assuming, that each block surfaces is a discontinuity, the mean block volume (V(b)), the mean volumetric joint count (J(vb)) and the mean block shape factor of the blocks are determined and compared with the estimated mean in situ block volumes (V(in)) and volumetric joint count (J(vi)) values estimated from the in situ discontinuity measurements. The established relations are presented as a chart to be used in practice for estimating the mean volume of blocks that can be obtained from a quarry site by analyzing the rock mass discontinuity spacing measurements.

  12. Block Volume Estimation from the Discontinuity Spacing Measurements of Mesozoic Limestone Quarries, Karaburun Peninsula, Turkey

    Directory of Open Access Journals (Sweden)

    Hakan Elci

    2014-01-01

    Full Text Available Block volumes are generally estimated by analyzing the discontinuity spacing measurements obtained either from the scan lines placed over the rock exposures or the borehole cores. Discontinuity spacing measurements made at the Mesozoic limestone quarries in Karaburun Peninsula were used to estimate the average block volumes that could be produced from them using the suggested methods in the literature. The Block Quality Designation (BQD ratio method proposed by the authors has been found to have given in the same order of the rock block volume to the volumetric joint count (Jv method. Moreover, dimensions of the 2378 blocks produced between the years of 2009 and 2011 in the working quarries have been recorded. Assuming, that each block surfaces is a discontinuity, the mean block volume (Vb, the mean volumetric joint count (Jvb and the mean block shape factor of the blocks are determined and compared with the estimated mean in situ block volumes (Vin and volumetric joint count (Jvi values estimated from the in situ discontinuity measurements. The established relations are presented as a chart to be used in practice for estimating the mean volume of blocks that can be obtained from a quarry site by analyzing the rock mass discontinuity spacing measurements.

  13. The response of macroinvertebrates to artificially enhanced detritus levels in plantation streams

    Directory of Open Access Journals (Sweden)

    J. L. Pretty

    2004-01-01

    Full Text Available The leaves and wood from vegetation surrounding headwater streams constitute a major food source for aquatic invertebrates, providing they are retained upon the streambed and not transported downstream. This study investigated the response of aquatic invertebrates to artificially increased detritus retention, in an effort to reproduce the naturally occurring build up of dead organic matter associated with streams in old-growth forest. The background detrital standing stock in streams in Kielder Forest (Northumberland, UK was low, approximately 32 gm-2. Two streams flowing through dense conifer plantation and one in open broadleaved woodland were manipulated by the addition of logs over a 10 m stream reach. After several months, log addition significantly enhanced detrital standing stocks in both conifer and broadleaved streams. Total invertebrate abundance, taxon richness and the numbers of certain numerically dominant families were significantly higher in experimental than reference reaches in both conifer and broadleaved streams. This response was most marked for detritivores, whilst non-detritivore groups often showed no response to the manipulation. Whilst in the short term the responses to enhanced retention may reflect a redistribution of the local fauna, it is argued that over a longer time-scale, a genuine increase in invertebrate density and diversity could occur. Allowing old-growth forest to develop in planted valley bottoms may be a viable management option for conservation. If established alongside streams, it would ensure continuous input of woody material and the fauna may benefit from the resulting increase in detritus retention. Keywords: forestry, detritivores, old-growth conifers, river management, woody debris

  14. Operational Group Sandy technical progress report

    Science.gov (United States)

    ,

    2013-01-01

    Hurricane Sandy made US landfall near Atlantic City, NJ on 29 October 2012, causing 72 direct deaths, displacing thousands of individuals from damaged or destroyed dwellings, and leaving over 8.5 million homes without power across the northeast and mid-Atlantic. To coordinate federal rebuilding activities in the affected region, the President established the cabinet-level Hurricane Sandy Rebuilding Task Force (Task Force). The Task Force was charged with identifying opportunities for achieving rebuilding success while supporting economic vitality, improving public health and safety, protecting and enhancing natural and manmade infrastructure, bolstering resilience, and ensuring appropriate accountability.

  15. Evolution of the alteration process in time of granitic materials from Valdemorillo quarries used in built heritage, Madrid, Spain

    Science.gov (United States)

    Alvarez de Buergo, M.; Fort, R.; Perez-Monserrat, E. M.

    2012-04-01

    Alteration of building materials used for heritage construction already starts in the quarries, where materials are subjected to both natural alteration and anthropic decay, this latter caused by the rock extracting, cutting and carving processes. Once the materials are placed in the building, they are exposed to other agents that accelerate their decay, especially if they are exposed to aggressive environments. Materials petrophysical properties tend to vary according to the alteration degree they have experienced, the longer they have been exposed to decay agents, the greater the properties change. Surface hardness of granitic rocks tend to diminish when they deteriorate, increasing its porosity, which usually is reflected on a decrease of the ultrasound propagation velocity measurements. Ultrasound velocity and surface hardness were measured in 200 monzogranite ashlars use to build the Assumption of Our Lady church (Valdemorillo, Madrid, Spain). Ultrasound velocity was measured using the indirect transmission mode, with 54 kHz frequency transductors, and surface hardness by means of the Schmidt hammer rebound tester. This monument was erected in different building stages. The starting point was a Mozarab or Visigoth defensive tower (8th century). Templars readapt it to a castle-convent (12th and 14th centuries), the tower being converted into a higher bell-tower. During the 14th-15th centuries the Cistercian Order made significant modifications of the complex, being the construction of the Chapter House one of the last enlargements during the 17th century. The quarries located in the surroundings of the monument were used for the first building stages. In the recent fronts of these quarries that have been used along the 20th century, ultrasound and hardness measurements were performed to obtain the values of these parameters in unaltered materials to compare them to those measured in ashlars from different constructive periods. A total of 50 recent front

  16. Composition of gypsum from the Koběřice quarry (Czech Republic)

    Czech Academy of Sciences Publication Activity Database

    Konečný, Pavel; Plevová, Eva; Vaculíková, Lenka; Kožušníková, Alena; Peterková, J.; Hundáková, M.

    2011-01-01

    Roč. 8, č. 2 (2011), s. 145-156 ISSN 1214-9705 Institutional research plan: CEZ:AV0Z30860518 Keywords : gypsum * Kobeřice quarry * spectroscopy Subject RIV: DB - Geology ; Mineralogy Impact factor: 0.530, year: 2011 http://www.irsm.cas.cz/abstracts/AGG/02_11/5_Konecny.pdf

  17. Final KC-46A Formal Training Unit (FTU) and First Main Operating Base (MOB 1) Beddown EIS

    Science.gov (United States)

    2014-03-01

    years old and constructed of vitrified clay pipe or concrete. Of the sanitary sewer lines field surveyed in 2004 and 2007, approximately 85 percent...Hollister soils are very deep and well-drained (USDA 2002a, 2003). The textures of the Tillman-Hollister soils range from clay loam to clay , with...The textures of the Miles-Nobscot soils range from sandy to sandy loam to sandy clay loam, with the Nobscot soils having a more sandy nature

  18. The sandy beach meiofauna and free-living nematodes from De Panne (Belgium)

    OpenAIRE

    Gheskiere, T.; Hoste, E.; Kotwicki, L.; Degraer, S.; Vanaverbeke, J.; Vincx, M.

    2002-01-01

    Despite their rather barren and arid appearance, European sandy beaches harbour a highly diverse fauna and flora and some of them are even highly productive. In contrast to tropical sandy beaches little is known about the structural and functional diversity of the different benthic components. This study aims to investigate the structural diversity of the meiobenthos, emphasizing on free-living marine nematodes on a Belgian sandy beach.The samples were collected on the sandy beach of De Panne...

  19. Wind sorting affects differently the organo-mineral composition of saltating and particulate materials in contrasting texture agricultural soils

    Science.gov (United States)

    Iturri, Laura Antonela; Funk, Roger; Leue, Martin; Sommer, Michael; Buschiazzo, Daniel Eduardo

    2017-10-01

    There is little information about the mineral and organic composition of sediments eroded by wind at different heights. Because of that, wind tunnel simulations were performed on four agricultural loess soils of different granulometry and their saltating materials collected at different heights. The particulate matter with an aerodynamic diameter mainly smaller than 10 μm (PM10) of these soils was obtained separately by a laboratory method. Results indicated that the granulometric composition of sediments collected at different heights was more homogeneous in fine- than in sandy-textured soils, which were more affected by sorting effects during wind erosion. This agrees with the preferential transport of quartz at low heights and of clay minerals at greater heights. SOC contents increased with height, but the composition of the organic materials was different: stable carboxylic acids, aldehydes, amides and aromatics were preferentially transported close to the ground because their were found in larger aggregates, while plant debris and polysaccharides, carbohydrates and derivatives of microbial origin from organic matter dominated at greater heights for all soil types. The amount of SOC in the PM10 fraction was higher when it was emitted from sandy than from fine textured soils. Because of the sorting process produced by wind erosion, the stable organic matter compounds will be transported at low heights and local scales, modifying soil fertility due to nutrient exportation, while less stable organic compounds will be part of the suspension losses, which are known to affect some processes at regional- or global scale.

  20. Comparative study of modified bitumen binder properties collected from mixing plant and quarry.

    Science.gov (United States)

    Mustafa Kamal, M.; Abu Bakar, R.; Hadithon, K. A.

    2017-11-01

    Quality control and assurance are essential in pavement construction. In general, the properties of bitumen change as it ages in bulk storage, transport, and storage on site. The minimization of bituminous hardening during storing, transportation and mixing depends on careful control of binder temperature. Hence therefore, bitumen should always be stored and handled at the lowest temperature possible, consistent with efficient use. The objective of the work is to monitor the quality of bitumen samples collected from mixing plant and quarry. Results showed that, samples modified bitumen which collected from quarry showed some adverse effects on rheological properties and physical properties after subjecting to high temperature storage within a period of time. The dynamic stiffness, elastic properties and other common binder properties were deteriorated too. The chemical changes that occurred during storage were analysed using Fourier transform infra-red spectroscopy (FTIR). Thus studies developed an understanding of bitumen ageing in storage.

  1. Anisotropy of magnetic susceptibility of silicic rocks from quarries in the vicinity of São Marcos, Rio Grande do Sul, South Brazil: Implications for emplacement mechanisms

    Science.gov (United States)

    Cañón-Tapia, Edgardo; Raposo, M. Irene B.

    2018-04-01

    The Paraná-Etendeka Large Igneous Province includes acid volcanic rocks that can be found throughout its extension. Several aspects concerning those rocks remain controversial, including their mechanism of emplacement and location of their eruptive sources. Opening of several quarries of dimension stone near the city of Sao Marcos, Rio Grande do Sul, Brazil, offers a unique opportunity to study in detail the acid products. Here, we present the results of a study of the anisotropy of magnetic susceptibility (AMS) completed in some rocks that had been interpreted as the roots of volcanic conduits. Our results, and reexamination of the textural features of the rocks, lead to a reinterpretation that suggests that these rocks were emplaced subaerially, and involved assimilation and remelting of clastic components of previous products. Due to the inferred conditions of emplacement, it is unlikely that the eruptive vents are located far from the area of study, therefore ruling out the long-travelled nature of these products.

  2. EAARL-B Coastal Topography--Eastern New Jersey, Hurricane Sandy, 2012: First Surface, Pre-Sandy

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — ASCII xyz and binary point-cloud data, as well as a digital elevation model (DEM) of a portion of the New Jersey coastline, pre- and post-Hurricane Sandy (October...

  3. [Effects of desertification on C and N storages in grassland ecosystem on Horqin sandy land].

    Science.gov (United States)

    Zhao, Ha-lin; Li, Yu-qiang; Zhou, Rui-lian

    2007-11-01

    Sandy grassland is widespread in northern China, where desertification is very common because of overgrazing and estrepement. However, little is known about the effects of desertification on grassland C and N storages in this region. A field survey was conducted on Horqin sandy grassland, and desertification gradients were established to evaluate the effects of desertification on C and N storages in soil, plant, and litter. The results showed that desertification had deep effects on the contents and storages of grassland C and N. The C and N contents and storages in the grassland decreased significantly with increasing desertification degree. Comparing with those in un-desertified grassland, the C and N contents in lightly, moderately, heavily, and severely desertified grasslands decreased by 56.06% and 48.72%, 78.43% and 74.36%, 88.95% and 84.62%, and 91.64% and 84.62% in 0-100 cm soil layer, and by 8.61% and 6.43%, 0.05% and 25.71%, 2.58% and 27.14%, and 8. 61% and 27. 86% in plant components, respectively. Relevantly, the C and N storages decreased by 50.95% and 43.38%, 75.19% and 71.04%, 86.76% and 81.48%, and 91.17% and 83.17% in plant underground components in 0-100 cm soil layer, and by 25.08% and 27.62%, 30.90% and 46.55%, 73.84% and 80.62%, and 90.89% and 87.31% in plant aboveground components, respectively. In 2000, the total area of desertified grassland in Horqin sandy land was 30152. 7 km2, and the C and N loss via desertification reached up to 107.53 and 9.97 Mt, respectively. Correlation analysis indicated that the decrease of soil C and N contents was mainly come from the decreased soil fine particles caused by wind erosion in the process of desertification, and the degradation of soil texture- and nutrient status led finally to the rapid decrease of C and N storages in plant biomass and litter.

  4. The millstone industry a summary of research on quarries and producers in the United States, Europe and elsewhere

    CERN Document Server

    Hockensmith, Charles D

    2009-01-01

    Since prehistoric times, the process of cutting rock to make millstones has been one of the most important industries in the world. The first part of this book compiles information on the millstone industry in the United States, which dates between the mid-1600s and the mid-1900s. Primarily based on archival research and brief accounts published in geological and historical volumes, it focuses on conglomerate, granite, flint, quartzite, gneiss, and sandstone quarries in different regions and states. The second part focuses on the millstone quarrying industry in Europe and other areas.

  5. Radon-222 signatures of natural ventilation regimes in an underground quarry.

    Science.gov (United States)

    Perrier, Frédéric; Richon, Patrick; Crouzeix, Catherine; Morat, Pierre; Le Mouël, Jean Louis

    2004-01-01

    Radon-222 activity concentration has been monitored since 1999 in an underground limestone quarry located in Vincennes, near Paris, France. It is homogeneous in summer, with an average value of 1700 Bq m(-3), and varies from 730 to 1450 Bq m(-3) in winter, indicating natural ventilation with a rate ranging from 0.5 to 2.4 x 10(-6) s(-1) (0.04-0.22 day(-1)). This hypothesis is supported by measurements in the vertical access pit where, in winter, a turbulent air current produces a stable radon profile, smoothly decreasing from 700 Bq m(-3) at 20 m depth to 300 Bq m(-3) at surface. In summer, a thermal stratification is maintained in the pit, but the radon-222 concentration jumps repeatedly between 100 and 2000 Bq m(-3). These jumps are due to atmospheric pressure pumping, which induces ventilation in the quarry at a rate of about 0.1 x 10(-6) s(-1) (0.009 day(-1)). Radon-222 monitoring thus provides a dynamical characterisation of ventilation regimes, which is important for the assessment of the long-term evolution of underground systems.

  6. Sandy soil plantation in semi-arid zones by polyacrylamide gel conditioner prepared by ionizing radiation. Part of a coordinated programme on radiation modified polymers for biomedical and biochemical applications

    International Nuclear Information System (INIS)

    Azzam, R.A.I.

    1983-07-01

    Polyacrylamide gel prepared by ionizing radiation was found to be capable of furnishing adequate conditions for sandy-soil plantation in semi-arid zones. The gel can be tailored for any soil texture under various climatic conditions. The sand-gel combination maintains three cycles of complete destruction and reformation without significant changes in erosion index. Water holding capacity and retention at different suctions in treated sand are increased. This increases water use efficiency. Fertilizers use efficiency is also increased to almost three times that of fertile clayey soil

  7. LOCAL TEXTURE DESCRIPTION FRAMEWORK FOR TEXTURE BASED FACE RECOGNITION

    Directory of Open Access Journals (Sweden)

    R. Reena Rose

    2014-02-01

    Full Text Available Texture descriptors have an important role in recognizing face images. However, almost all the existing local texture descriptors use nearest neighbors to encode a texture pattern around a pixel. But in face images, most of the pixels have similar characteristics with that of its nearest neighbors because the skin covers large area in a face and the skin tone at neighboring regions are same. Therefore this paper presents a general framework called Local Texture Description Framework that uses only eight pixels which are at certain distance apart either circular or elliptical from the referenced pixel. Local texture description can be done using the foundation of any existing local texture descriptors. In this paper, the performance of the proposed framework is verified with three existing local texture descriptors Local Binary Pattern (LBP, Local Texture Pattern (LTP and Local Tetra Patterns (LTrPs for the five issues viz. facial expression, partial occlusion, illumination variation, pose variation and general recognition. Five benchmark databases JAFFE, Essex, Indian faces, AT&T and Georgia Tech are used for the experiments. Experimental results demonstrate that even with less number of patterns, the proposed framework could achieve higher recognition accuracy than that of their base models.

  8. Benthic algae stimulate leaf litter decomposition in detritus-based headwater streams: a case of aquatic priming effect?

    Science.gov (United States)

    Danger, Michael; Cornut, Julien; Chauvet, Eric; Chavez, Paola; Elger, Arnaud; Lecerf, Antoine

    2013-07-01

    In detritus-based ecosystems, autochthonous primary production contributes very little to the detritus pool. Yet primary producers may still influence the functioning of these ecosystems through complex interactions with decomposers and detritivores. Recent studies have suggested that, in aquatic systems, small amounts of labile carbon (C) (e.g., producer exudates), could increase the mineralization of more recalcitrant organic-matter pools (e.g., leaf litter). This process, called priming effect, should be exacerbated under low-nutrient conditions and may alter the nature of interactions among microbial groups, from competition under low-nutrient conditions to indirect mutualism under high-nutrient conditions. Theoretical models further predict that primary producers may be competitively excluded when allochthonous C sources enter an ecosystem. In this study, the effects of a benthic diatom on aquatic hyphomycetes, bacteria, and leaf litter decomposition were investigated under two nutrient levels in a factorial microcosm experiment simulating detritus-based, headwater stream ecosystems. Contrary to theoretical expectations, diatoms and decomposers were able to coexist under both nutrient conditions. Under low-nutrient conditions, diatoms increased leaf litter decomposition rate by 20% compared to treatments where they were absent. No effect was observed under high-nutrient conditions. The increase in leaf litter mineralization rate induced a positive feedback on diatom densities. We attribute these results to the priming effect of labile C exudates from primary producers. The presence of diatoms in combination with fungal decomposers also promoted decomposer diversity and, under low-nutrient conditions, led to a significant decrease in leaf litter C:P ratio that could improve secondary production. Results from our microcosm experiment suggest new mechanisms by which primary producers may influence organic matter dynamics even in ecosystems where autochthonous

  9. Genesis of Hurricane Sandy (2012) Simulated with a Global Mesoscale Model

    Science.gov (United States)

    Shen, Bo-Wen; DeMaria, Mark; Li, J.-L. F.; Cheung, S.

    2013-01-01

    In this study, we investigate the formation predictability of Hurricane Sandy (2012) with a global mesoscale model. We first present five track and intensity forecasts of Sandy initialized at 00Z 22-26 October 2012, realistically producing its movement with a northwestward turn prior to its landfall. We then show that three experiments initialized at 00Z 16-18 October captured the genesis of Sandy with a lead time of up to 6 days and simulated reasonable evolution of Sandy's track and intensity in the next 2 day period of 18Z 21-23 October. Results suggest that the extended lead time of formation prediction is achieved by realistic simulations of multiscale processes, including (1) the interaction between an easterly wave and a low-level westerly wind belt (WWB) and (2) the appearance of the upper-level trough at 200 hPa to Sandy's northwest. The low-level WWB and upper-level trough are likely associated with a Madden-Julian Oscillation.

  10. Investigation of superstorm Sandy 2012 in a multi-disciplinary approach

    Science.gov (United States)

    Kunz, M.; Mühr, B.; Kunz-Plapp, T.; Daniell, J. E.; Khazai, B.; Wenzel, F.; Vannieuwenhuyse, M.; Comes, T.; Elmer, F.; Schröter, K.; Fohringer, J.; Münzberg, T.; Lucas, C.; Zschau, J.

    2013-10-01

    At the end of October 2012, Hurricane Sandy moved from the Caribbean Sea into the Atlantic Ocean and entered the United States not far from New York. Along its track, Sandy caused more than 200 fatalities and severe losses in Jamaica, The Bahamas, Haiti, Cuba, and the US. This paper demonstrates the capability and potential for near-real-time analysis of catastrophes. It is shown that the impact of Sandy was driven by the superposition of different extremes (high wind speeds, storm surge, heavy precipitation) and by cascading effects. In particular the interaction between Sandy and an extra-tropical weather system created a huge storm that affected large areas in the US. It is examined how Sandy compares to historic hurricane events, both from a hydro-meteorological and impact perspective. The distribution of losses to different sectors of the economy is calculated with simple input-output models as well as government estimates. Direct economic losses are estimated about USD 4.2 billion in the Caribbean and between USD 78 and 97 billion in the US. Indirect economic losses from power outages is estimated in the order of USD 16.3 billion. Modelling sector-specific dependencies quantifies total business interruption losses between USD 10.8 and 15.5 billion. Thus, seven years after the record impact of Hurricane Katrina in 2005, Hurricane Sandy is the second costliest hurricane in the history of the United States.

  11. Investigation of superstorm Sandy 2012 in a multi-disciplinary approach

    Directory of Open Access Journals (Sweden)

    M. Kunz

    2013-10-01

    Full Text Available At the end of October 2012, Hurricane Sandy moved from the Caribbean Sea into the Atlantic Ocean and entered the United States not far from New York. Along its track, Sandy caused more than 200 fatalities and severe losses in Jamaica, The Bahamas, Haiti, Cuba, and the US. This paper demonstrates the capability and potential for near-real-time analysis of catastrophes. It is shown that the impact of Sandy was driven by the superposition of different extremes (high wind speeds, storm surge, heavy precipitation and by cascading effects. In particular the interaction between Sandy and an extra-tropical weather system created a huge storm that affected large areas in the US. It is examined how Sandy compares to historic hurricane events, both from a hydro-meteorological and impact perspective. The distribution of losses to different sectors of the economy is calculated with simple input-output models as well as government estimates. Direct economic losses are estimated about USD 4.2 billion in the Caribbean and between USD 78 and 97 billion in the US. Indirect economic losses from power outages is estimated in the order of USD 16.3 billion. Modelling sector-specific dependencies quantifies total business interruption losses between USD 10.8 and 15.5 billion. Thus, seven years after the record impact of Hurricane Katrina in 2005, Hurricane Sandy is the second costliest hurricane in the history of the United States.

  12. Analysis of effect of aluminized canfo on fragmentation and economics of quarry blast

    International Nuclear Information System (INIS)

    Shoukat, M.R.; Akram, M.

    2016-01-01

    Reducing the explosive cost for drilling and blasting operations conducted at limestone quarries is a major concern for every mine operator. In Pakistan, to reduce explosive cost, Calcium Ammonium Nitrate with Fuel Oil (CANFO) is commonly used in explosive column charge in place of Ammonium nitrate fuel oil (ANFO). However, fragmentation of the blast has to be compromised over cost reduction. Hence it is desired to enhance the performance of CANFO. In this study, Aluminum (AL) is added into Calcium Ammonium Nitrate (CAN) to analyze its effect on fragmentation and economics of blast at a limestone quarry. Experimental shots were held using rectangular drilling pattern (current practice), using CANFO and ALCANFO in separate shots, while all other blast design factors were kept constant. Post blast analysis for all shots was done in terms of fragmentation and cost. The shots using ALCANFO proved to be better fragmentation wise, and also assured a saving of 1.6% in drilling and blasting costs. (author)

  13. Autogenous Tumbling Media Assessment to Clean Weathered Surfaces of Waste-Rock Particles from a Basalt Quarry

    Directory of Open Access Journals (Sweden)

    Baran Tufan

    2015-06-01

    Full Text Available In this study, the optimum feed composition in autogenous tumbling of basalt waste-rock particles to clean their weathered surface was determined. The weathered surfaces of basalt are generally cut out consequent to extraction of basalt columns in quarry operations. The inefficiently cut out portions of basalt cause formation of huge quarry waste dumps causing visual pollution on roadsides. Mixtures of different particle size fractions of basalt waste-rock particles were experimented to achieve the optimum feed material composition. The minimum loss of commercially available basalt particles and maximum clear surface was intended. The results were compared with respect to weight loss (% and reflectance values of used and generated samples.

  14. Fragmentation, Cost and Environmental Effects of Plaster Stemming Method for Blasting at A Basalt Quarry

    Science.gov (United States)

    Cevizci, Halim

    2014-10-01

    In this study, the plaster stemming application for blasting at a basalt quarry is studied. Drill cuttings are generally used in open pits and quarries as the most common stemming material since these are most readily available at blast sites. However, dry drill cuttings eject very easily from blastholes without offering much resistance to blast energy. The plaster stemming method has been found to be better than the drill cuttings stemming method due to increased confinement inside the hole and better utilization of blast explosive energy in the rock. The main advantage of the new stemming method is the reduction in the cost of blasting. At a basalt quarry, blasting costs per unit volume of rock were reduced to 15% by increasing burden and spacing distances. In addition, better fragmentation was obtained by using the plaster stemming method. Blast trials showed that plaster stemming produced finer material. In the same blast tests, +30 cm size fragments were reduced to 47.3% of the total, compared to 32.6% in the conventional method of drill cuttings stemming. With this method of stemming, vibration and air shock values increased slightly due to more blast energy being available for rock breakage but generally these increased values were small and stayed under the permitted limit for blast damage criteria unless measuring distance is too close.

  15. On the Impact Angle of Hurricane Sandy's New Jersey Landfall

    Science.gov (United States)

    Hall, Timothy M.; Sobel, Adam H.

    2013-01-01

    Hurricane Sandy's track crossed the New Jersey coastline at an angle closer to perpendicular than any previous hurricane in the historic record, one of the factors contributing to recordsetting peak-water levels in parts of New Jersey and New York. To estimate the occurrence rate of Sandy-like tracks, we use a stochastic model built on historical hurricane data from the entire North Atlantic to generate a large sample of synthetic hurricanes. From this synthetic set we calculate that under long-term average climate conditions, a hurricane of Sandy's intensity or greater (category 1+) makes NJ landfall at an angle at least as close to perpendicular as Sandy's at an average annual rate of 0.0014 yr-1 (95% confidence range 0.0007 to 0.0023); i.e., a return period of 714 years (95% confidence range 435 to 1429).

  16. Utilization of shallow-water seagrass detritus by Caribbean deep-sea macrofauna: delta13C evidence

    International Nuclear Information System (INIS)

    Suchanek, T.H.; Williams, S.L.; Ogden, J.C.; Hubbard, D.K.; Gill, I.P.

    1985-01-01

    Three dives were made using the DSRV Alvin in the deep-sea basin north of St. Croix, Virgin Islands. Detrital seagrasses and macrofaunal distributions at 2455 to 3950 m depth were assessed quantitatively. Counts of the manatee grass Syringodium filiforme contrasted sharply with those of the turtle grass Thalassia testudinum, reflecting an abundance proportional to previously reported export rates of the same species from Tague Bay, a nearby shallow source lagoon. Of the macrofaunal consumers that could potentially utilize this detrital nutrient source, three species of holothurians and two species of sea urchins were collected and/or observed. Gut content analyses revealed that all three holothurians deposit-feed on sediment and at least one species of sea urchin feeds almost exclusively on Syringodium. Carbon:nitrogen analyses of naturally occurring abyssal Thalassia detritus showed very low nitrogen content and a high C:N ratio, thus yielding a low nutritional value. Fresh Thalassia blades held in a litter bag experiment at 3950 m changed little in nitrogen content and C:N ratio after four years. A comparison was made of the stable carbon isotope ratios of 13 C: 12 C for abyssal seagrass detritus and other potential carbon sources with those for tissues from the holothurian and urchin consumers. The results are discussed. (author)

  17. Sandy Hook : alternative access concept plan and vehicle replacement study

    Science.gov (United States)

    2009-06-01

    This study addresses two critical issues of concern to the Sandy Hook Unit of Gateway National : Recreational Area: (1) options for alternative access to Sandy Hook during peak summer season, : particularly when the park is closed to private vehicles...

  18. Preparation of Sandy Soil Stabilizer for Roads Based on Radiation Modified Polymer Composite

    International Nuclear Information System (INIS)

    Elnahas, H.H.

    2016-01-01

    Radiation modified polymer composite (RMPC) was studied to build an extremely durable sandy road, construct a trail or bath, or control dust and erosion. A dilute solution of composite binds sandy soil fines through a coagulation bonding process. The result is a dense soil structure that has superior resistance to cracks and water penetration and can also solve erosion control problems. In erosion control applications, diluted composite is merely sprayed into sandy soil without compaction, effectively sealing the surface to prevent air-born dust or deterioration from erosion. The prepared composite has an elastic and melt-able film formation that imparts thermal compacting to the stabilized sandy soil after full dryness for sandy road leveling, repairing and restoration processes. The prepared composite is environmentally economical when compared with traditional sandy soil stabilizing (SSS) or sealing methods.

  19. Deaths associated with Hurricane Sandy - October-November 2012.

    Science.gov (United States)

    2013-05-24

    On October 29, 2012, Hurricane Sandy hit the northeastern U.S. coastline. Sandy's tropical storm winds stretched over 900 miles (1,440 km), causing storm surges and destruction over a larger area than that affected by hurricanes with more intensity but narrower paths. Based on storm surge predictions, mandatory evacuations were ordered on October 28, including for New York City's Evacuation Zone A, the coastal zone at risk for flooding from any hurricane. By October 31, the region had 6-12 inches (15-30 cm) of precipitation, 7-8 million customers without power, approximately 20,000 persons in shelters, and news reports of numerous fatalities (Robert Neurath, CDC, personal communication, 2013). To characterize deaths related to Sandy, CDC analyzed data on 117 hurricane-related deaths captured by American Red Cross (Red Cross) mortality tracking during October 28-November 30, 2012. This report describes the results of that analysis, which found drowning was the most common cause of death related to Sandy, and 45% of drowning deaths occurred in flooded homes in Evacuation Zone A. Drowning is a leading cause of hurricane death but is preventable with advance warning systems and evacuation plans. Emergency plans should ensure that persons receive and comprehend evacuation messages and have the necessary resources to comply with them.

  20. Acidification of sandy grasslands - consequences for plant diversity

    DEFF Research Database (Denmark)

    Olsson, Pål Axel; Mårtensson, Linda-Maria; Bruun, Hans Henrik

    2009-01-01

    soil; a number of nationally red-listed species showed a similar pattern. Plant species diversity and number of red-listed species increased with slope. Where the topsoil had been acidified, limestone was rarely present above a depth of 30 cm. The presence of limestone restricts the availability......Questions: (1) Does soil acidification in calcareous sandy grasslands lead to loss of plant diversity? (2) What is the relationship between the soil content of lime and the plant availability of mineral nitrogen (N) and phosphorus (P) in sandy grasslands? Location: Sandy glaciofluvial deposits......). Environmental variables were recorded at each plot, and soil samples were analysed for exchangeable P and N, as well as limestone content and pH. Data were analysed with regression analysis and canonical correspondence analysis. Results: Plant species richness was highest on weakly acid to slightly alkaline...

  1. Ion beam texturing

    Science.gov (United States)

    Hudson, W. R.

    1977-01-01

    A microscopic surface texture was created by sputter-etching a surface while simultaneously sputter-depositing a lower sputter yield material onto the surface. A xenon ion-beam source was used to perform the texturing process on samples as large as 3-cm diameter. Textured surfaces have been characterized with SEM photomicrographs for a large number of materials including Cu, Al, Si, Ti, Ni, Fe, stainless steel, Au, and Ag. A number of texturing parameters are studied including the variation of texture with ion-beam powder, surface temperature, and the rate of texture growth with sputter etching time.

  2. THE ECOLOGICAL STRUCTURE OF ORIBATID MITES POPULATION (‘OSNOVNOY’ QUARRY, DONETSK REGION

    Directory of Open Access Journals (Sweden)

    Shtirts А. D.

    2015-08-01

    Full Text Available In the successional recovery processes of quarry-spoiled systems soil-living oribatide mites, who are one of the pioneer groups inhabiting anthropogenically transformed areas, play a significant role. The aim of our study was to research composition and characteristics of oribatide mites ecological community structure of the ‘Osnovnoy’ quarry (PJSC ‘HeidelbergCement Ukraine’ in Amvrosievsky district of Donetsk region. The material was collected in 2012. In total, 37 standard soil samples of 250 cm3 were collected, from which 1086 adult specimen, who belong to 61 species, were extracted in April. The collection of soil samples and forcing of oribatides in thermoelectors was conducted by the conventional method of E. M. Bulanovа-Zahvatkinа. To analyze the communities domination structure the gradations of dominance by the means of G. Engelmann scale was used. The analysis of the oribatides morpho-ecological types distribution was held in accordance to the work of D. A. Krivolutsky. To assess the ecological diversity of oribatides communities the indices of Shannon, Pielou, Simpson and Margalef were used. On the territory of the «Osnovnoy» quarry, a specific complex with a unique oribatid species composition was detected (two new species were found for the fauna of Ukraine noted earlier for the steppes of Mongolia: Ghilarovus khentiicus Bayartogtokh, Smelyansky, 2007 and Hemileius humeralis Perez-Inigo, 1990. During the analysis of the oribatide communities ecological structure low rates of average population density (7280-11410 ind./m2 were observed with high species wealth (61 species found. The maximum figure made up in spring, the minimum – in summer. The ecological diversity indexes are quite high, thus the maximum for Shannon index in spring is 2.89, which is comparable to that of the conserved areas. The quarry dominant species are Multioppia glabra, Protoribates capucinus, Tectocepheus velatus, Scheloribates laevigatus, and

  3. Quarries as educational resources - a research with students of a secondary school of Portugal

    Science.gov (United States)

    Filipe, Fernanda; Henriques, Maria Helena

    2015-04-01

    This work describes the results obtained in a research on science education involving 18 students of Biology and Geology of the 10th grade (15 years old) of the Secondary School of Figueiró dos Vinhos (Central Portugal). Framed on the curricular topic "Earth, a very special planet", the research included the conception, implementation and evaluation of an educational intervention aiming to answer the question: "How to stimulate meaningful and relevant learning about sustainable exploitation of geological resources, namely limestone?" The intervention occurred along 8 classes of 90 minutes each, which included practical work developed in small groups (3 students/each), and several activities both in the field and in the classroom (prior and after the fieldtrip). From the methodological point of view, this research is qualitative in nature, a study-case type, with data resulting from direct observation and content analysis of the answers presented by students to questionnaires (diagnostic and intervention assessment) and to worksheets, expressly created for the research. The main goal of the intervention was that the students, by developing practical activities centered upon a field trip to an abandoned limestone quarry located close to their homes, could learn to recognize the geological impacts arising from the exploitation of geological resources and acquire skills for collecting and processing relevant information about existing rules that control the operations in quarries, in order to develop critical thinking about the nature of exploitation of these types of resources, which may hinder the promotion of sustainable development. Concerning the intervention assessment, results reinforced the idea that quarries can provide an educational resource of great value for promoting substantive knowledge on geosciences, urgently needed and consistent with the development of critical and intervenient citizens, able to decide, at the right moment, how to behave

  4. Dump evaluation for landscape restoration of an ancient cacareous quarry

    International Nuclear Information System (INIS)

    Paredes, R.; Ayala, R.; Trevisiol, S.

    2010-01-01

    This work is about the geological - mining study in the limestone quarry in the west of Valle Hermoso town - Cordoba - Argentina. The generation of dump material is considered a waste but is inherent to the process of rocks and minerals extraction. The dump stocks evaluation take into account the different types of rocks with physical and chemical characteristics. The dump has several carbonatic qualities and can be given useful to uncover material originally dismissed as to be used as crushed stone for concrete and others.The reuse of this waste can be allocated primarily to the construction industry, and explore other potential uses, would rehabilitate these lands, and thus eliminate an environmental liability .This work is about the geological - mining study in the limestone quarry in the west of Valle Hermoso town - Cordoba - Argentina. The generation of dump material is considered a waste but is inherent to the process of rocks and minerals extraction. The dump stocks evaluation take into account the different types of rocks with physical and chemical characteristics. The dump has several carbonatic qualities and can be given useful to uncover material originally dismissed as to be used as crushed stone for concrete and others.The reuse of this waste can be allocated primarily to the construction industry, and explore other potential uses, would rehabilitate these lands, and thus eliminate an environmental liability

  5. Long-range laser scanning and 3D imaging for the Gneiss quarries survey

    Science.gov (United States)

    Schenker, Filippo Luca; Spataro, Alessio; Pozzoni, Maurizio; Ambrosi, Christian; Cannata, Massimiliano; Günther, Felix; Corboud, Federico

    2016-04-01

    In Canton Ticino (Southern Switzerland), the exploitation of natural stone, mostly gneisses, is an important activity of valley's economies. Nowadays, these economic activities are menaced by (i) the exploitation costs related to geological phenomena such as fractures, faults and heterogeneous rocks that hinder the processing of the stone product, (ii) continuously changing demand because of the evolving natural stone fashion and (iii) increasing administrative limits and rules acting to protect the environment. Therefore, the sustainable development of the sector for the next decades needs new and effective strategies to regulate and plan the quarries. A fundamental step in this process is the building of a 3D geological model of the quarries to constrain the volume of commercial natural stone and the volume of waste. In this context, we conducted Terrestrial Laser Scanning surveys of the quarries in the Maggia Valley to obtain a detailed 3D topography onto which the geological units were mapped. The topographic 3D model was obtained with a long-range laser scanning Riegl VZ4000 that can measure from up to 4 km of distance with a speed of 147,000 points per second. It operates with the new V-line technology, which defines the surface relief by sensing differentiated signals (echoes), even in the presence of obstacles such as vegetation. Depending on the esthetics of the gneisses, we defined seven types of natural stones that, together with faults and joints, were mapped onto the 3D models of the exploitation sites. According to the orientation of the geological limits and structures, we projected the different rock units and fractures into the excavation front. This way, we obtained a 3D geological model from which we can quantitatively estimate the volume of the seven different natural stones (with different commercial value) and waste (with low commercial value). To verify the 3D geological models and to quantify exploited rock and waste volumes the same

  6. Selection of site specific vibration equation by using analytic hierarchy process in a quarry

    Energy Technology Data Exchange (ETDEWEB)

    Kalayci, Ulku, E-mail: ukalayci@istanbul.edu.tr; Ozer, Umit, E-mail: uozer@istanbul.edu.tr

    2016-01-15

    This paper presents a new approach for the selection of the most accurate SSVA (Site Specific Vibration Attenuation) equation for blasting processes in a quarry located near settlements in Istanbul, Turkey. In this context, the SSVA equations obtained from the same study area in the literature were considered in terms of distance between the shot points and buildings and the amount of explosive charge. In this purpose, 11 different SSVA equations obtained from the study area in the past 12 years, forecasting capabilities according to designated new conditions, using 102 vibration records as test data obtained from the study area was investigated. In this study, AHP (Analytic Hierarchy Process) was selected as an analysis method in order to determine the most accurate equation among 11 SSAV equations, and the parameters such as year, distance, charge, and r{sup 2} of the equations were used as criteria for AHP. Finally, the most appropriate equation was selected among the existing ones, and the process of selecting according to different target criteria was presented. Furthermore, it was noted that the forecasting results of the selected equation is more accurate than that formed using the test results. - Highlights: • The optimum Site Specific Vibration Attenuation equation for blasting in a quarry located near settlements was determined. • It is indicated that SSVA equations changing over the years don’t give always accurate estimates at changing conditions. • Selection of the blast induced SSVA equation was made using AHP. • Equation selection method was highlighted based on parameters such as charge, distance, and quarry geometry changes (year).

  7. Selection of site specific vibration equation by using analytic hierarchy process in a quarry

    International Nuclear Information System (INIS)

    Kalayci, Ulku; Ozer, Umit

    2016-01-01

    This paper presents a new approach for the selection of the most accurate SSVA (Site Specific Vibration Attenuation) equation for blasting processes in a quarry located near settlements in Istanbul, Turkey. In this context, the SSVA equations obtained from the same study area in the literature were considered in terms of distance between the shot points and buildings and the amount of explosive charge. In this purpose, 11 different SSVA equations obtained from the study area in the past 12 years, forecasting capabilities according to designated new conditions, using 102 vibration records as test data obtained from the study area was investigated. In this study, AHP (Analytic Hierarchy Process) was selected as an analysis method in order to determine the most accurate equation among 11 SSAV equations, and the parameters such as year, distance, charge, and r"2 of the equations were used as criteria for AHP. Finally, the most appropriate equation was selected among the existing ones, and the process of selecting according to different target criteria was presented. Furthermore, it was noted that the forecasting results of the selected equation is more accurate than that formed using the test results. - Highlights: • The optimum Site Specific Vibration Attenuation equation for blasting in a quarry located near settlements was determined. • It is indicated that SSVA equations changing over the years don’t give always accurate estimates at changing conditions. • Selection of the blast induced SSVA equation was made using AHP. • Equation selection method was highlighted based on parameters such as charge, distance, and quarry geometry changes (year).

  8. The brass-type texture and its deviation from the copper-type texture

    DEFF Research Database (Denmark)

    Leffers, Torben; Ray, R.K.

    2009-01-01

    Our basic aim with the present review is to address the classical problem of the “fcc rolling texture transition” – the fact that fcc materials may, depending on material parameters and rolling conditions, develop two different types of rolling textures, the copper-type texture and the brass...... the subject and sketch our approach for dealing with it. We then recapitulate the decisive progress made during the nineteen sixties in the empirical description of the fcc rolling texture transition and in lining up a number of possible explanations. Then follows a section about experimental investigations...... of the brass-type texture after the nineteen sixties covering texture measurements and microstructural investigations. The main observations are: (1) The brass-type texture deviates from the copper-type texture from an early stage of texture development. (2) Deformation twinning has a decisive effect...

  9. Rates of Hospitalization for Dehydration Following Hurricane Sandy in New Jersey.

    Science.gov (United States)

    Swerdel, Joel N; Rhoads, George G; Cosgrove, Nora M; Kostis, John B

    2016-04-01

    Hurricane Sandy, one of the most destructive natural disasters in New Jersey history, made landfall on October 29, 2012. Prolonged loss of electrical power and extensive infrastructure damage restricted access for many to food and water. We examined the rate of dehydration in New Jersey residents after Hurricane Sandy. We obtained data from 2008 to 2012 from the Myocardial Infarction Data Acquisition System (MIDAS), a repository of in-patient records from nonfederal New Jersey hospitals (N=517,355). Patients with dehydration had ICD-9-CM discharge diagnosis codes for dehydration, volume depletion, and/or hypovolemia. We used log-linear modeling to estimate the change in in-patient hospitalizations for dehydration comparing 2 weeks after Sandy with the same period in the previous 4 years (2008-2011). In-patient hospitalizations for dehydration were 66% higher after Sandy than in 2008-2011 (rate ratio [RR]: 1.66; 95% confidence interval [CI]: 1.50, 1.84). Hospitalizations for dehydration in patients over 65 years of age increased by nearly 80% after Sandy compared with 2008-2011 (RR: 1.79; 95% CI: 1.58, 2.02). Sandy was associated with a marked increase in hospitalizations for dehydration. Reducing the rate of dehydration following extreme weather events is an important public health concern that needs to be addressed, especially in those over 65 years of age.

  10. Hurricane Sandy, Disaster Preparedness, and the Recovery Model.

    Science.gov (United States)

    Pizzi, Michael A

    2015-01-01

    Hurricane Sandy was the second largest and costliest hurricane in U.S. history to affect multiple states and communities. This article describes the lived experiences of 24 occupational therapy students who lived through Hurricane Sandy using the Recovery Model to frame the research. Occupational therapy student narratives were collected and analyzed using qualitative methods and framed by the Recovery Model. Directed content and thematic analysis was performed using the 10 components of the Recovery Model. The 10 components of the Recovery Model were experienced by or had an impact on the occupational therapy students as they coped and recovered in the aftermath of the natural disaster. This study provides insight into the lived experiences and recovery perspectives of occupational therapy students who experienced Hurricane Sandy. Further research is indicated in applying the Recovery Model to people who survive disasters. Copyright © 2015 by the American Occupational Therapy Association, Inc.

  11. Evaluation of the effect of initial texture on the development of deformation texture

    DEFF Research Database (Denmark)

    Leffers, Torben; Juul Jensen, Dorte

    1986-01-01

    The authors describe a computer procedure which allows them to introduce experimental initial textures as starting conditions for texture simulation (instead of a theoretical random texture). They apply the procedure on two batches of copper with weak initial textures and on fine-grained and coarse......-grained aluminium with moderately strong initial textures. In copper the initial texture turns out to be too weak to have any significant effect. In aluminium the initial texture has a very significant effect on the simulated textures-similar to the effect it has on the experimental textures. However......, there are differences between the simulated and the experimental aluminium textures that can only be explained as a grain-size effect. Possible future applications of the procedure are discussed...

  12. Combining fine texture and coarse color features for color texture classification

    Science.gov (United States)

    Wang, Junmin; Fan, Yangyu; Li, Ning

    2017-11-01

    Color texture classification plays an important role in computer vision applications because texture and color are two fundamental visual features. To classify the color texture via extracting discriminative color texture features in real time, we present an approach of combining the fine texture and coarse color features for color texture classification. First, the input image is transformed from RGB to HSV color space to separate texture and color information. Second, the scale-selective completed local binary count (CLBC) algorithm is introduced to extract the fine texture feature from the V component in HSV color space. Third, both H and S components are quantized at an optimal coarse level. Furthermore, the joint histogram of H and S components is calculated, which is considered as the coarse color feature. Finally, the fine texture and coarse color features are combined as the final descriptor and the nearest subspace classifier is used for classification. Experimental results on CUReT, KTH-TIPS, and New-BarkTex databases demonstrate that the proposed method achieves state-of-the-art classification performance. Moreover, the proposed method is fast enough for real-time applications.

  13. Evidence for opal phytolith preservation in the Langebaanweg ‘E’ Quarry Varswater Formation and its potential for palaeohabitat reconstruction

    Directory of Open Access Journals (Sweden)

    P. Haarhof

    2010-01-01

    Full Text Available At the end of the Miocene epoch, C4 grasslands began to expand at the expense of tree-, shrub- and forb-dominated C3 ecosystems. While C4 grasses were spreading throughout most regions of the world, C3 grasses may have been spreading along South Africa’s southwest coast. Stable isotope analyses of hypsodont fossil ungulates from ‘E’ Quarry, a well-known Late Miocene/Early Pliocene fossil locality near the town of Langebaanweg, suggest that the local environment might have included a substantial C3 grass component. Besides this indirect evidence, little is known about the evolution, nature and importance of grass in the ‘E’ Quarry biome. As a preliminary step towards addressing these questions, we initiated a trial investigation to assess whether sediments at the site are conducive to the preservation of phytoliths, an important tool in the reconstruction of palaeohabitats. Results indicate that fossil phytoliths are sufficiently well preserved to allow a comprehensive analysis of the ‘E’ Quarry phytolith assemblage.

  14. Water retention and availability in soils of the State of Santa Catarina-Brazil: effect of textural classes, soil classes and lithology

    Directory of Open Access Journals (Sweden)

    André da Costa

    2013-12-01

    Full Text Available The retention and availability of water in the soil vary according to the soil characteristics and determine plant growth. Thus, the aim of this study was to evaluate water retention and availability in the soils of the State of Santa Catarina, Brazil, according to the textural class, soil class and lithology. The surface and subsurface horizons of 44 profiles were sampled in different regions of the State and different cover crops to determine field capacity, permanent wilting point, available water content, particle size, and organic matter content. Water retention and availability between the horizons were compared in a mixed model, considering the textural classes, the soil classes and lithology as fixed factors and profiles as random factors. It may be concluded that water retention is greater in silty or clayey soils and that the organic matter content is higher, especially in Humic Cambisols, Nitisols and Ferralsol developed from igneous or sedimentary rocks. Water availability is greater in loam-textured soils, with high organic matter content, especially in soils of humic character. It is lower in the sandy texture class, especially in Arenosols formed from recent alluvial deposits or in gravelly soils derived from granite. The greater water availability in the surface horizons, with more organic matter than in the subsurface layers, illustrates the importance of organic matter for water retention and availability.

  15. Superstorm Sandy and the Verdant Power RITE Project

    Science.gov (United States)

    Corren, D.; Colby, J.; Adonizio, M.

    2013-12-01

    On October 29, 2012 Superstorm Sandy (formerly Hurricane Sandy) made landfall in New Jersey. One of the deadliest, and second-costliest hurricane in US history, Sandy was the largest Atlantic hurricane on record, with a diameter of 1,800 km. It was this unprecedented size, extreme central low pressure, and full-moon timing that created a storm surge which inundated New York City with record-breaking water levels, resulting in tremendous destruction of buildings and infrastructure. At its RITE (Roosevelt Island Tidal Energy) Project in New York City's East River, Verdant Power has been installing demonstration and commercial turbine systems since 2005, along with performing related environmental monitoring and measurements. The RITE site is located in the East Channel of the East River, on the east side of Roosevelt Island. All along the East River, large areas of the adjacent boroughs were impacted by Sandy, including flooding of the subway tunnels under the river. When Sandy struck, Verdant had recently concluded a two-week in-water test at RITE of a new rotor for its Gen5 KHPS (Kinetic Hydropower System) turbine, with funding assistance by partners NYSERDA and the US Department of Energy. While the turbine had already been removed from its mounting in the river bottom in September, Verdant continued to operate two water measurement instruments in the river. These acoustic Doppler current profilers (ADCPs) measure the 3-D water velocity at various heights in the water column, and are also equipped to provide water level data. Verdant is interested in the effects such an extreme storm could have on turbines and other equipment installed in this river reach, as is planned by Verdant under a 10-year commercial pilot project licensed by the Federal Energy Regulatory Commission (FERC) for up to 30 turbines. Associated equipment includes navigational aids (buoys and signage), which Verdant is required to maintain to exclude vessels from the project boundaries. The East

  16. The marble quarries of Macael. From “free and communal” to council property

    International Nuclear Information System (INIS)

    Carretero Gómez, A.; Aznar Sánchez, J.A.

    2017-01-01

    The fate of the inhabitants of Macael has been closely linked to the production of marble from time immemorial. The scope of these resources transcended local borders during the latter part of last century; thus, in the last few years, the marble extracted from the surroundings of Macael accounted for over 40% of the national production, with Spain being one of the leading world producers of this ornamental rock. This paper analyzes the changes that have taken place in the quarry access system since 1573, when the town of Macael was surveyed, up to the present time. After many historical changes in which the people of Macael have had to fight for ownership of the quarries, both against private interests and public administration, the assets which were communal, and therefore freely accessible to the locals, became the property of the Local Council, which at present also holds the exploitation concession of the marble resources and the power to grant leases to entrepreneurs wishing to extract this mineral. [es

  17. Minimising Backbreak at the Dewan Cement Limestone Quarry Using an Artificial Neural Network

    Science.gov (United States)

    Muhammad, Khan; Shah, Akram

    2017-12-01

    Backbreak, defined as excessive breakage behind the last row of blastholes in blasting operations at a quarry, causes destabilisation of rock slopes, improper fragmentation, minimises drilling efficiency. In this paper an artificial neural network (ANN) is applied to predict backbreak, using 12 input parameters representing various controllable factors, such as the characteristics of explosives and geometrical blast design, at the Dewan Cement limestone quarry in Hattar, Pakistan. This ANN was trained with several model architectures. The 12-2-1 ANN model was selected as the simplest model yielding the best result, with a reported correlation coefficient of 0.98 and 0.97 in the training and validation phases, respectively. Sensitivity analysis of the model suggested that backbreak can be reduced most effectively by reducing powder factor, blasthole inclination, and burden. Field tests were subsequently carried out in which these sensitive parameters were varied accordingly; as a result, backbreak was controlled and reduced from 8 m to less than a metre. The resulting reduction in powder factor (kg of explosives used per m3 of blasted material) also reduced blasting costs.

  18. A RCRA clean closure of a unique site - Kerr Hollow quarry at the Y-12 Plant

    International Nuclear Information System (INIS)

    Stone, J.E.; Yemington, C.

    1991-01-01

    An abandoned rock quarry, Kerr Hollow Quarry (KHQ), near the DOE Oak Ridge Y-12 Plant, Oak Ridge, Tennessee, was used from 1951-1988 as a site to treat RCRA wastes which were reactive, corrosive, or ignitable and which posed major concerns for personnel safety. The wastes were generated from operations at the Y-12 Plant and Oak Ridge National Laboratory and were previously treated by allowing the wastes to react with the water in KHQ. When closure of the site was required by the RCRA regulations, a closure method was selected to allow for clean closure of the quarry without treatment or removal of the water in KHQ. The method proposed to and approved by the Tennessee Department of Health and Environment (TDHE) was one of surveying the containers in the quarry by a submersible Remotely Operated Vehicle (ROV) using sonar and visually inspecting the containers by camera to confirm that all containers are breached and empty. Any container found intact would be breached to allow the contents to react with water and form non-hazardous residue. The progress of this unique type of closure is presented along with a summary of the problems encountered, planning activities, equipment utilized and other information about the closure. All work was done with remotely operated equipment. This work is being performed by Sonsub, Inc. This closure project showed the practicality and cost benefits of telerobotic systems for work on hazardous waste sites. In addition to the intangible benefit of reduced exposure of workers, insurance costs are much lower and efficiency is higher. Daily start-up time is reduced since there is no need to don protective suits or other gear. Productivity is higher since personnel work only in clean areas where they are not hampered by protective gear. Cleanup time at shift end is minimized since the remote equipment does not leave the hazardous area and personnel need not go through decontamination

  19. Responses of plant available water and forest productivity to variably layered coarse textured soils

    Science.gov (United States)

    Huang, Mingbin; Barbour, Lee; Elshorbagy, Amin; Si, Bing; Zettl, Julie

    2010-05-01

    Reforestation is a primary end use for reconstructed soils following oil sands mining in northern Alberta, Canada. Limited soil water conditions strongly restrict plant growth. Previous research has shown that layering of sandy soils can produce enhanced water availability for plant growth; however, the effect of gradation on these enhancements is not well defined. The objective of this study was to evaluate the effect of soil texture (gradation and layering) on plant available water and consequently on forest productivity for reclaimed coarse textured soils. A previously validated system dynamics (SD) model of soil moisture dynamics was coupled with ecophysiological and biogeochemical processes model, Biome-BGC-SD, to simulate forest dynamics for different soil profiles. These profiles included contrasting 50 cm textural layers of finer sand overlying coarser sand in which the sand layers had either a well graded or uniform soil texture. These profiles were compared to uniform profiles of the same sands. Three tree species of jack pine (Pinus banksiana Lamb.), white spruce (Picea glauce Voss.), and trembling aspen (Populus tremuloides Michx.) were simulated using a 50 year climatic data base from northern Alberta. Available water holding capacity (AWHC) was used to identify soil moisture regime, and leaf area index (LAI) and net primary production (NPP) were used as indices of forest productivity. Published physiological parameters were used in the Biome-BGC-SD model. Relative productivity was assessed by comparing model predictions to the measured above-ground biomass dynamics for the three tree species, and was then used to study the responses of forest leaf area index and potential productivity to AWHC on different soil profiles. Simulated results indicated soil layering could significantly increase AWHC in the 1-m profile for coarse textured soils. This enhanced AWHC could result in an increase in forest LAI and NPP. The increased extent varied with soil

  20. Sorção do imazapyr em solos com diferentes texturas Imazapyr sorption in soils with different textures

    Directory of Open Access Journals (Sweden)

    L.E. Firmino

    2008-06-01

    Full Text Available O conhecimento do comportamento de herbicidas no ambiente, sobretudo no solo, permite a predição de possíveis impactos do seu uso em sistemas agrícolas. Com o intuito de avaliar a sorção do herbicida imazapyr no solo, foi realizado um experimento, utilizando sorgo (Sorghum bicolor como planta bioindicadora. A sorção do imazapyr foi avaliada em areia lavada e em três solos, com as seguintes texturas: muito argilosa, franco-argilo-arenosa e areia-franca, provenientes, respectivamente, das cidades de Sete Lagoas, João Pinheiro e Rio Casca, em Minas Gerais. Foram determinados: o valor de I50 (dose que inibiu 50% no acúmulo de massa seca da planta-teste e a relação de sorção [RS = (I50 solo -I 50 areia/I50 areia]. Os valores de I50 observados foram: 29,41; 10,20 e 7,33 mg kg-1, e a relação de sorção (RS: 9,77; 2,73 e 1,68, respectivamente para os solos muito argiloso, franco-argilo-arenoso e areia franca. O herbicida imazapyr apresentou a seguinte ordem de sorção nos substratos: muito argiloso > franco-argilo-arenoso > areia-franca > areia lavada. Em solos arenosos e com baixos teores de matéria orgânica, a baixa sorção do imazapyr predispõe o produto à lixiviação no perfil do solo, podendo contaminar mananciais de águas subterrâneas.Knowledge about herbicide behavior in the environment, especially in soil, allows predicting possible impacts caused by its use in agricultural systems. An experiment using Sorghum bicolor as a bio-indicator was carried out to evaluate imazapyr sorption in soil. Sorption was evaluated in washed sand and in soils of 3 different textures: very clayed, sandy clayed loam and sandy loam, respectively from Sete Lagoas, João Pinheiro and Rio Casca - Minas Gerais. The value of I50, which inhibits 50% of dry biomass accumulation of the test-plant, and sorption relation (SR = I50 soil - I50 sand/I50 sand were determined. I50 values observed were 29.41, 10.20 and 7.33 mg kg-1 and SR values were 9

  1. Hurricane Sandy (New Jersey): Mortality Rates in the Following Month and Quarter.

    Science.gov (United States)

    Kim, Soyeon; Kulkarni, Prathit A; Rajan, Mangala; Thomas, Pauline; Tsai, Stella; Tan, Christina; Davidow, Amy

    2017-08-01

    To describe changes in mortality after Hurricane Sandy made landfall in New Jersey on October 29, 2012. We used electronic death records to describe changes in all-cause and cause-specific mortality overall, in persons aged 76 years or older, and by 3 Sandy impact levels for the month and quarter following Hurricane Sandy compared with the same periods in earlier years adjusted for trends. All-cause mortality increased 6% (95% confidence interval [CI] = 2%, 11%) for the month, 5%, 8%, and 12% by increasing Sandy impact level; and 7% (95% CI = 5%, 10%) for the quarter, 5%, 8%, and 15% by increasing Sandy impact level. In elderly persons, all-cause mortality rates increased 10% (95% CI = 5%, 15%) and 13% (95% CI = 10%, 16%) in the month and quarter, respectively. Deaths that were cardiovascular disease-related increased by 6% in both periods, noninfectious respiratory disease-related by 24% in the quarter, infection-related by 20% in the quarter, and unintentional injury-related by 23% in the month. Mortality increased, heterogeneous by cause, for both periods after Hurricane Sandy, particularly in communities more severely affected and in the elderly, who may benefit from supportive services.

  2. Noise-induced hearing loss among quarry workers in a north-eastern state of malaysia: a study on knowledge, attitude and practice.

    Science.gov (United States)

    Ismail, Ahmad Filza; Daud, Aziah; Ismail, Zaliha; Abdullah, Baharudin

    2013-09-01

    Noise is known to be one of the environmental and occupational hazards listed in the Factory and Machinery Act 1967. Quarries with loud deafening sounds from trucks and machineries pose the risk of noise-induced hearing loss to workers. This study was designed to assess the knowledge, attitude and practice towards noise-induced hearing loss and to determine the prevalence of noise-induced hearing loss and its associated factors among quarry workers in a north-eastern state of Malaysia. A cross-sectional study was conducted at six quarries in a north-eastern state of Malaysia, with 97 consented respondents who answered a validated version of a questionnaire and underwent pure tone audiogram. The respondents were male, aged between 18 to 50 years, working in the quarry area for at least 6-months duration with no family history of ear diseases. The mean percentage scores of knowledge, attitude and practice were 44 (11), 70 (10) and 28 (16) percent, respectively. The prevalence of noise-induced hearing loss was found to be 57 (95% CI: 47, 67) with 46 (84%) having mild and moderate noise-induced hearing loss, and 34 (62%) involved both ears. Multiple logistic regressions showed that age and practice score were the associated factors with odd ratios of 1.1 (95% CI: 1.1, 1.2; phearing loss was contributed by factors such as poor practice and old age.

  3. Proposed plan for the management of bulk wastes at the Weldon Spring quarry, Weldon Spring, Missouri

    International Nuclear Information System (INIS)

    1990-02-01

    This proposed plan addresses the management of contaminated bulk wastes at the Weldon Spring quarry. Activities at the site are being conducted by the US Department of Energy under its Surplus Facilities Management Program. A remedial investigation/feasibility study has been prepared in accordance with requirements of the Comprehensive Environmental Response. The purposes of the proposed plan are to present a notice and brief analysis of the proposed quarry bulk waste remedial action, describe the remedial action alternatives for this interim remedial action, identify the currently preferred alternative for managing the bulk wastes and present the rationale for this preference, serve as a companion document to the RI/FS and administrative record file for this action, and outline the public's role in the decision-making process for this action. 2 figs., 4 tabs

  4. TEXTURAL FRACTOGRAPHY

    Directory of Open Access Journals (Sweden)

    Hynek Lauschmann

    2011-05-01

    Full Text Available The reconstitution of the history of a fatigue process is based on the knowledge of any correspondences between the morphology of the crack surface and the velocity of the crack growth (crack growth rate - CGR. The textural fractography is oriented to mezoscopic SEM magnifications (30 to 500x. Images contain complicated textures without distinct borders. The aim is to find any characteristics of this texture, which correlate with CGR. Pre-processing of images is necessary to obtain a homogeneous texture. Three methods of textural analysis have been developed and realized as computational programs: the method based on the spectral structure of the image, the method based on a Gibbs random field (GRF model, and the method based on the idealization of light objects into a fibre process. In order to extract and analyze the fibre process, special methods - tracing fibres and a database-oriented analysis of a fibre process - have been developed.

  5. Family Structures, Relationships, and Housing Recovery Decisions after Hurricane Sandy

    Directory of Open Access Journals (Sweden)

    Ali Nejat

    2016-04-01

    Full Text Available Understanding of the recovery phase of a disaster cycle is still in its infancy. Recent major disasters such as Hurricane Sandy have revealed the inability of existing policies and planning to promptly restore infrastructure, residential properties, and commercial activities in affected communities. In this setting, a thorough grasp of housing recovery decisions can lead to effective post-disaster planning by policyholders and public officials. The objective of this research is to integrate vignette and survey design to study how family bonds affected rebuilding/relocating decisions after Hurricane Sandy. Multinomial logistic regression was used to investigate respondents’ family structures before Sandy and explore whether their relationships with family members changed after Sandy. The study also explores the effect of the aforementioned relationship and its changes on households’ plans to either rebuild/repair their homes or relocate. These results were compared to another multinomial logistic regression which was applied to examine the impact of familial bonds on respondents’ suggestions to a vignette family concerning rebuilding and relocating after a hurricane similar to Sandy. Results indicate that respondents who lived with family members before Sandy were less likely to plan for relocating than those who lived alone. A more detailed examination shows that this effect was driven by those who improved their relationships with family members; those who did not improve their family relationships were not significantly different from those who lived alone, when it came to rebuilding/relocation planning. Those who improved their relationships with family members were also less likely to suggest that the vignette family relocate. This study supports the general hypothesis that family bonds reduce the desire to relocate, and provides empirical evidence that family mechanisms are important for the rebuilding/relocating decision

  6. Are sugarcane leaf-detritus well colonized by aquatic macroinvertebrates?

    Directory of Open Access Journals (Sweden)

    Luciene Aparecida Leite-Rossi

    Full Text Available AIM: The aim was to compare the kinetics of decomposition and the colonization of leaf litter of two plant species, the native Talauma ovata (pinha-do-brejo and the exotic Saccharum officinarum (sugarcane, by aquatic macroinvertebrates; METHODS: From each substrate, three recipients of colonization were taken from a stream, and the specimens identified to the lowest taxonomic level on days 7, 15, 34, 44, 61 and 75. The debris was weighed at the beginning and end of the experiment and determined their cell wall fractions; RESULTS: The coefficients of mineralization indicated higher velocity decay of organic matter refractory in T. ovata. There was no difference in taxonomic structure of macroinvertebrates, between the two substrates, but the community exhibited distinct functional feeding groups in the peak of colonization, with a greater number of shredders in T. ovata. The successive states of decomposition of the two plant detritus showed distinct macroinvertebrate densities; CONCLUSIONS: The amount and state of the plant biomass were important factors influencing the density and diversity of the macroinvertebrate fauna throughout the process of organic decomposition.

  7. The fate of fresh and stored 15N-labelled sheep urine and urea applied to a sandy and a sandy loam soil using different application strategies

    DEFF Research Database (Denmark)

    Sørensen, P.; Jensen, E.S.

    1996-01-01

    The fate of nitrogen from N-15-labelled sheep urine and urea applied to two soils was studied under field conditions. Labelled and stored urine equivalent to 204 kg N ha(-1) was either incorporated in soil or applied to the soil surface prior to sowing of Italian ryegrass (Lolium multiflorum L...... and soil was not significantly different for incorporated urine and urea. Almost all the supplied labelled N was accounted for in soil and herbage in the sandy loam soil, whereas 33-34% of the labelled N was unaccounted for in the sandy soil. When the stored urine was applied to the soil surface, 20...... was applied to growing ryegrass at the sandy loam soil, the immobilization of urine-derived N was significantly reduced compared to application prior to sowing. The results indicated that the net mineralization of urine N was similar to that of urea in the sandy soil, but only about 75% of the urine N was net...

  8. Sandy a změna klimatu

    Czech Academy of Sciences Publication Activity Database

    Pecho, Jozef

    2013-01-01

    Roč. 92, č. 7 (2013), s. 408-411 ISSN 0042-4544 Institutional support: RVO:68378289 Keywords : hurricanes * climate change Subject RIV: DG - Athmosphere Sciences, Meteorology http://www.vesmir.cz/clanek/sandy-a-zmena-klimatu

  9. Sinnerite, Cu6As4S9, from the Lengenbach Quarry, Binn Valley, Switzerland

    DEFF Research Database (Denmark)

    Bindi, Luca; Makovicky, Emil; Nestola, Fabrizio

    2013-01-01

    We have characterized the crystal structure of sinnerite, Cu6As4S9, a rare sulfosalt mineral from the ores of the Lengenbach quarry, Binn Valley, Canton Valais, Switzerland, by single-crystal X-ray diffraction and chemical analysis. We found sinnerite to be structurally identical to synthetic Cu6As...

  10. 77 FR 10472 - San Bernardino National Forest, Mountaintop Ranger District, California, Mitsubishi South Quarry...

    Science.gov (United States)

    2012-02-22

    ... of the mine. The proposed South Quarry site would be able to meet the requirements for blending with... restoration practices. 3. To avoid incidental killing of birds protected under the Migratory Bird Treaty Act... proponent's ability to mine its claims on National Forest System lands. San Bernardino County will decide...

  11. Grape yield, and must compounds of 'Cabernet Sauvignon' grapevine in sandy soil with potassium contents increasing

    Directory of Open Access Journals (Sweden)

    Marlise Nara Ciotta

    2016-08-01

    Full Text Available ABSTRACT: Content of exchangeable potassium (K in t soil may influence on its content in grapevines leaves, grape yield, as well as, in must composition. The study aimed to assess the interference of exchangeable K content in the soil on its leaf content, production and must composition of 'Cabernet Sauvignon' cultivar. In September 2011, in Santana do Livramento (RS five vineyards with increasing levels of exchangeable K in the soil were selected. In the 2012/13 and 2013/14 harvests, the grape yield, yield components, total K content in the leaves in full bloom and berries veraison were evaluated. Values of total soluble sugar (TSS, pH, total titratable acidity (TTA, total polyphenols and anthocyanins were evaluated in the must. Exchangeable K content increase in soil with sandy surface texture increased its content in leaves collected during full flowering and in berries and must pH; however, it did not affect production of the 'Cabernet Sauvignon'.

  12. Assessing the role of coastal characteristics in erosional process of rocky shores by boulder quarrying.

    Science.gov (United States)

    Causon Deguara, Joanna; Gauci, Ritienne

    2017-04-01

    Rocky coasts are considered as relatively stable coastlines, subject to erosional processes that change the landscape over long periods of time. Block quarrying is one such process, occurring when hydraulic pressure from wave impact dislodges boulders from within the outcropping bedrock. These dislodged boulders can be either deposited inland or dragged seaward by further wave action. This process can be evidenced from boulder deposits on the coast, as well as sockets and detachment scarps that are identified at the shoreline and in the backshore. This study seeks to identify the role of attributes such as aspect, geological structure and water depth have on erosion of rocky coasts through boulder quarrying processes. This is being done through observation of coastline morphology and an analysis of boulder accumulations and erosional features identified on a 3km stretch of rocky shore. The study area is situated on the SE coast of the Island of Malta (Central Mediterranean). The coastline being analysed generally trends NW - SE and consists of a series of limestone beds that dip slightly towards the NE. The boulder deposits observed along the site vary in size, quantity and position with respect to the shoreline. Whilst some areas exhibit large boulder accumulations, other areas are distinguished by the complete absence of such deposits. Taking into consideration the wave climate, the variable size, quantity and distribution of boulder accumulations observed along the site may indicate that geological structure and aspect play an important role in boulder dislodgment by wave action. Key words: rock coast, boulder quarrying, erosional process, Malta

  13. Reliability estimate of unconfined compressive strength of black cotton soil stabilized with cement and quarry dust

    Directory of Open Access Journals (Sweden)

    Dayo Oluwatoyin AKANBI

    2017-06-01

    Full Text Available Reliability estimates of unconfined compressive strength values from laboratory results for specimens compacted at British Standard Light (BSLfor compacted quarry dust treated black cotton soil using cement for road sub – base material was developed by incorporating data obtained from Unconfined compressive strength (UCS test gotten from the laboratory test to produce a predictive model. Data obtained were incorporated into a FORTRAN-based first-order reliability program to obtain reliability index values. Variable factors such as water content relative to optimum (WRO, hydraulic modulus (HM, quarry dust (QD, cement (C, Tri-Calcium silicate (C3S, Di-calcium silicate (C2S, Tri-Calcium Aluminate (C3A, and maximum dry density (MDD produced acceptable safety index value of1.0and they were achieved at coefficient of variation (COV ranges of 10-100%. Observed trends indicate that WRO, C3S, C2S and MDD are greatly influenced by the COV and therefore must be strictly controlled in QD/C treated black cotton soil for use as sub-base material in road pavements. Stochastically, British Standard light (BSL can be used to model the 7 days unconfined compressive strength of compacted quarry dust/cement treated black cotton soil as a sub-base material for road pavement at all coefficient of variation (COV range 10 – 100% because the safety index obtained are higher than the acceptable 1.0 value.

  14. Abrasive wear based predictive maintenance for systems operating in sandy conditions

    NARCIS (Netherlands)

    Woldman, M.; Tinga, T.; Heide, E. van der; Masen, M.A.

    2015-01-01

    Machines operating in sandy environments are damaged by the abrasive action of sand particles that enter the machine and become entrapped between components and contacting surfaces. In the case of the military services the combination of a sandy environment and the wide range of tasks to be

  15. The Effect of Mangrove Leaf Litter Enrichment on Macrobenthic Colonization of Defaunated Sandy Substrates

    Science.gov (United States)

    Lee, S. Y.

    1999-11-01

    The importance of exported mangrove materials to nearshore macrobenthos has largely been predicted based upon decomposition and utilization studies conducted within the mangrove environment, and from quantitative measurements of export. The present study evaluated the impact of mangrove leaf litter enrichment on non-mangrove substrates in a high-salinity microcosm experiment. Fortnightly addition of Kandelia candel leaf detritus at levels equivalent to 0·66 and 0·33 mg cm -2day -1in defaunated sand in microcosms maintained under high salinity conditions and on a sandy substrate resulted in no significant differences from the control in total faunal dry biomass or ash-free dry weight (AFDW) after 28, 73, 137 and 217 days of experiment. Duration of experiment was significant in determining the biomass (both dry weight and AFDW) of the macrofaunal assemblage in the microcosms, but neither enrichment nor its interaction with time had an effect. Species richness, Shannon diversity and evenness, and the total number of individuals, however, decreased in the order control>low enrichment>high enrichment for almost all sampling dates. By contrast, soluble tannins in the microcosm sediment demonstrated the reverse pattern. Both duration of experiment and enrichment were significant in determining species richness and the total number of individuals. The interaction between time and enrichment level was significant in the former but not the latter case. Discriminant analysis performed on the species abundance data indicated distinct animal assemblages characteristic of the three enrichment levels. These findings suggest that mangrove organic matter may not necessarily result in enhancement effects on marine benthos but high concentrations of tannins may hamper colonization by the macrobenthos.

  16. The effect of vegetation and soil texture on the nature of organics in runoff from a catchment supplying water for domestic consumption.

    Science.gov (United States)

    Awad, John; van Leeuwen, John; Abate, Dawit; Pichler, Markus; Bestland, Erick; Chittleborough, David J; Fleming, Nigel; Cohen, Jonathan; Liffner, Joel; Drikas, Mary

    2015-10-01

    The influence of vegetation and soil texture on the concentration and character of dissolved organic matter (DOM) present in runoff from the surface and sub-surface of zero order catchments of the Myponga Reservoir-catchment (South Australia) was investigated to determine the impacts of catchment characteristics and land management practices on the quality of waters used for domestic supply. Catchments selected have distinct vegetative cover (grass, native vegetation or pine) and contrasting texture of the surface soil horizon (sand or clay loam/clay). Water samples were collected from three slope positions (upper, middle, and lower) at soil depths of ~30 cm and ~60 cm in addition to overland flows. Filtered (0.45 μm) water samples were analyzed for dissolved organic carbon (DOC) and UV-visible absorbance and by F-EEM and HPSEC with UV and fluorescence detection to characterize the DOM. Surface and sub-surface runoff from catchments with clay soils and native vegetation or grass had lower DOC concentrations and lower relative abundances of aromatic, humic-like and high molecular weight organics than runoff from sandy soils with these vegetative types. Sub-surface flows from two catchments with Pinus radiata had similar DOC concentrations and DOM character, regardless of marked variation in surface soil texture. Runoff from catchments under native vegetation and grass on clay soils resulted in lower DOC concentrations and hence would be expected to have lower coagulant demand in conventional treatment for potable water supply than runoff from corresponding sandy soil catchments. However, organics in runoff from clay catchments would be more difficult to remove by coagulation. Surface waters from the native vegetation and grass catchments were generally found to have higher relative abundance of organic compounds amenable to removal by coagulation compared with sub-surface waters. Biophysical and land management practices combine to have a marked influence on the

  17. Reducing the risk of the collapse of the soil by macro system modeling the slopes stability of the quarries

    Science.gov (United States)

    Klimova, E. V.; Semeykin, A. Yu

    2018-01-01

    The urgent task of modern production is to reduce the risks of man-made disasters and, as a consequence, preserve the life and health of workers, material properties and natural environment. In the mining industry, one of the reasons for the high level of injuries and accidents is the collapse of the soil. Macro system modelling of slopes stability of the quarries is based on the compliance with the conditions of physical and mathematical correctness of the application of the model of a continuous medium. This type of modelling allows to choose the safe parameters of the slopes of the quarries and to reduce the risk of collapse of the soil.

  18. Measuring Sandy Bottom Dynamics by Exploiting Depth from Stereo Video Sequences

    DEFF Research Database (Denmark)

    Musumeci, Rosaria E.; Farinella, Giovanni M.; Foti, Enrico

    2013-01-01

    In this paper an imaging system for measuring sandy bottom dynamics is proposed. The system exploits stereo sequences and projected laser beams to build the 3D shape of the sandy bottom during time. The reconstruction is used by experts of the field to perform accurate measurements and analysis...

  19. Remedial investigation work plan for Chestnut Ridge Operable Unit 4 (Rogers Quarry/Lower McCoy Branch) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    The Oak Ridge Y-12 Plant includes - 800 acres near the northeast comer of the reservation and adjacent to the city of Oak Ridge (Fig. 1-1). The plant is a manufacturing and developmental engineering facility that produced components for various nuclear weapons systems and provides engineering support to other Energy Systems facilities. More than 200 contaminated sites have been identified at the Y-12 Plant that resulted from past waste management practices. Many of the sites have operable units (OUs) based on priority and on investigative and remediation requirements. This Remedial Investigation RI work plan specifically addresses Chestnut Ridge OU 4. Chestnut Ridge OU 4 consists of Rogers Quarry and Lower McCoy Branch (MCB). Rogers Quarry, which is also known as Old Rogers Quarry or Bethel Valley Quarry was used for quarrying from the late 1940s or early 1950s until about 1960. Since that time, the quarry has been used for disposal of coal ash and materials from Y-12 production operations, including classified materials. Disposal of coal ash ended in July 1993. An RI is being conducted at this site in response to CERCLA regulations. The overall objectives of the RI are to collect data necessary to evaluate the nature and extent of contaminants of concern, support an Ecological Risk Assessment and a Human Health Risk Assessment, support the evaluation of remedial alternatives, and ultimately develop a Record of Decision for the site. The purpose of this work plan is to outline RI activities necessary to define the nature and extent of suspected contaminants at Chestnut Ridge OU 4. Potential migration pathways also will be investigated. Data collected during the RI will be used to evaluate the risk posed to human health and the environment by OU 4.

  20. Experimental approach toward understanding the role of meiofauna in a detritus based marine food web

    International Nuclear Information System (INIS)

    Lee, J.J.; Tenore, K.R.; Tietjen, J.H.; Mastropaolo, C.

    1976-01-01

    The rate of detrital degradation was measured in three model systems maintained in chemostats. Each 1 l reaction vessel contained natural sediment carefully removed from the surface of a salt marsh at low tide. Alternate freezing and thawing killed indigenous organisms in the substrate. At the beginning of each experiment 14 C labeled Zostera detritus and filtered ( 32 P as a tracer indicated that 2 of the 3 meiofaunal species and their food were not consumed or assimilated in sufficient quantity to be major constituents of the diet of Capitella

  1. Transportation during and after Hurricane Sandy.

    Science.gov (United States)

    2012-11-01

    "Hurricane Sandy demonstrated the strengths and limits of the transportation infrastructure in New York City and the surrounding region. As a result of the timely and thorough preparations by New York City and the MTA, along with the actions of city ...

  2. Will the future atmospheric circulation favor the landfall of Sandy-like superstorms? (Invited)

    Science.gov (United States)

    Barnes, E. A.; Polvani, L. M.; Sobel, A. H.

    2013-12-01

    Superstorm Sandy ravaged the Eastern seaboard of the United States, costing a great number of lives and billions of dollars in damage. Whether events like Sandy will become more frequent as anthropogenic greenhouse gases continue to increase remains an open and complex question. Here, we consider whether the persistent large-scale atmospheric patterns that steered Sandy onto the coast will become more frequent in the coming decades. Using the CMIP5 multi-model ensemble, we demonstrate that climate models consistently project a decrease in the frequency and persistence of the westward flow that led to Sandy's unprecedented track, implying that future atmospheric conditions are less likely than at present to propel storms westward into the coast.

  3. Assessment of Environmental Impacts of Limestone Quarrying Operations in Thailand

    Science.gov (United States)

    Kittipongvises, Suthirat

    2017-11-01

    Environmental impacts of the mineral extraction have been a public concern. Presently, there is widespread global interest in the area of mining and its sustainability that focused on the need to shift mining industry to a more sustainable framework. The aim of this study was to systematically assess all possible environmental and climate change related impacts of the limestone quarrying operation in Thailand. By considering the life cycle assessment method, the production processes were divided into three phases: raw material extraction, transportation, and comminution. Both IMPACT 2002+ and the Greenhouse Gas Protocol methods were used. Results of IMPACT 2002+ analysis showed that per 1 ton crushed limestone rock production, the total depletion of resource and GHGs emissions were 79.6 MJ and 2.76 kg CO2 eq., respectively. Regarding to the four damage categories, `resources' and `climate change' categories were the two greatest environmental impacts of the limestone rock production. Diesel fuel and electricity consumption in the mining processes were the main causes of those impacts. For climate change, the unit of CO2 eq. was expressed to quantify the total GHGs emissions. Estimated result was about 3.13 kg CO2 eq. per ton limestone rock product. The results obtained by the Greenhouse Gas Protocol were also similar to IMPACT 2002+ method. Electrical energy consumption was considered as the main driver of GHGs, accounting for approximately 46.8 % of total fossil fuel CO2 emissions. A final point should be noted that data uncertainties in environmental assessment over the complete life cycle of limestone quarrying operation have to be carefully considered.

  4. The quarry and workshop of Barranco Cardones (Gran Canaria, Canary Islands: Basalt quern production using stone tools

    Directory of Open Access Journals (Sweden)

    Yurena Naranjo-Mayor

    2016-09-01

    This paper analyses the operational sequence, that is, the different phases of the extraction and fashioning techniques of basalt rotary querns based on the recent finds of two quarries located near the coast (Cardones and Cebolla and a quern manufacturing workshop (Cave 36, Arucas Municipality in a ravine about 600 m inland. Traditionally it was thought that the Pre-European population of Gran Canaria fashioned their querns from naturally detached volcanic surface blocks collected in ravines or along the coast. This supposition was based on the idea that the early Canarians were not capable of extracting blocks from bedrock with stone tools. This notion, however, has been proven wrong by the circular extraction negatives on the quarry faces and by finds of stone fashioning tools in the workshop.

  5. Effects of Pisha sandstone content on solute transport in a sandy soil.

    Science.gov (United States)

    Zhen, Qing; Zheng, Jiyong; He, Honghua; Han, Fengpeng; Zhang, Xingchang

    2016-02-01

    In sandy soil, water, nutrients and even pollutants are easily leaching to deeper layers. The objective of this study was to assess the effects of Pisha sandstone on soil solute transport in a sandy soil. The miscible displacement technique was used to obtain breakthrough curves (BTCs) of Br(-) as an inert non-adsorbed tracer and Na(+) as an adsorbed tracer. The incorporation of Pisha sandstone into sandy soil was able to prevent the early breakthrough of both tracers by decreasing the saturated hydraulic conductivity compared to the controlled sandy soil column, and the impeding effects increased with Pisha sandstone content. The BTCs of Br(-) were accurately described by both the convection-dispersion equation (CDE) and the two-region model (T-R), and the T-R model fitted the experimental data slightly better than the CDE. The two-site nonequilibrium model (T-S) accurately fit the Na(+) transport data. Pisha sandstone impeded the breakthrough of Na(+) not only by decreasing the saturated hydraulic conductivity but also by increasing the adsorption capacity of the soil. The measured CEC values of Pisha sandstone were up to 11 times larger than those of the sandy soil. The retardation factors (R) determined by the T-S model increased with increasing Pisha sandstone content, and the partition coefficient (K(d)) showed a similar trend to R. According to the results of this study, Pisha sandstone can successfully impede solute transport in a sandy soil column. Copyright © 2015 Elsevier Ltd. All rights reserved.

  6. Migration characteristics of cobalt-60 through sandy soil in high pH solution

    International Nuclear Information System (INIS)

    Ohnuki, Toshihiko

    1992-01-01

    Migration characteristics of 60 Co through sandy soil in high pH solution has been investigated by both column and batch techniques. The association of 60 Co with the sandy soil and its components were studied by sequential extraction techniques. The concentration profile of 60 Co in the sandy soil column was composed of two exponential curves showing that 60 Co would consist of immobile and mobile fractions. The immobile 60 Co was retained by the sandy soil and was distributed near the top. Though the mobile 60 Co was little sorbed by soil and migrated through the soil column, maximum concentration of 60 Co in the effluents decreased slightly with increasing path length of the soil column. The sequential extraction of 60 Co from the sandy soil and from its components showed that 60 Co was sorbed by both manganese oxide and clay minerals. And manganese oxide is one of the responsible soil components for the observed decrease in the maximum concentration of 60 Co in the effluents. Although the content of manganese oxide in the sandy soil was 0.13%, manganese oxide is the important component to prevent from the migration of 60 Co in the high pH solution. (author)

  7. Symmetric textures

    International Nuclear Information System (INIS)

    Ramond, P.

    1993-01-01

    The Wolfenstein parametrization is extended to the quark masses in the deep ultraviolet, and an algorithm to derive symmetric textures which are compatible with existing data is developed. It is found that there are only five such textures

  8. Longitudinal Impact of Hurricane Sandy Exposure on Mental Health Symptoms.

    Science.gov (United States)

    Schwartz, Rebecca M; Gillezeau, Christina N; Liu, Bian; Lieberman-Cribbin, Wil; Taioli, Emanuela

    2017-08-24

    Hurricane Sandy hit the eastern coast of the United States in October 2012, causing billions of dollars in damage and acute physical and mental health problems. The long-term mental health consequences of the storm and their predictors have not been studied. New York City and Long Island residents completed questionnaires regarding their initial Hurricane Sandy exposure and mental health symptoms at baseline and 1 year later (N = 130). There were statistically significant decreases in anxiety scores (mean difference = -0.33, p Hurricane Sandy has an impact on PTSD symptoms that persists over time. Given the likelihood of more frequent and intense hurricanes due to climate change, future hurricane recovery efforts must consider the long-term effects of hurricane exposure on mental health, especially on PTSD, when providing appropriate assistance and treatment.

  9. 33 CFR 80.170 - Sandy Hook, NJ to Tom's River, NJ.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Sandy Hook, NJ to Tom's River, NJ. 80.170 Section 80.170 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Atlantic Coast § 80.170 Sandy Hook, NJ to Tom's River...

  10. Legal Considerations for Health Care Practitioners After Superstorm Sandy.

    Science.gov (United States)

    Hershey, Tina Batra; Van Nostrand, Elizabeth; Sood, Rishi K; Potter, Margaret

    2016-06-01

    During disaster response and recovery, legal issues often arise related to the provision of health care services to affected residents. Superstorm Sandy led to the evacuation of many hospitals and other health care facilities and compromised the ability of health care practitioners to provide necessary primary care. This article highlights the challenges and legal concerns faced by health care practitioners in the aftermath of Sandy, which included limitations in scope of practice, difficulties with credentialing, lack of portability of practitioner licenses, and concerns regarding volunteer immunity and liability. Governmental and nongovernmental entities employed various strategies to address these concerns; however, legal barriers remained that posed challenges throughout the Superstorm Sandy response and recovery period. We suggest future approaches to address these legal considerations, including policies and legislation, additional waivers of law, and planning and coordination among multiple levels of governmental and nongovernmental organizations. (Disaster Med Public Health Preparedness. 2016;10:518-524).

  11. Rebuilding Emergency Care After Hurricane Sandy.

    Science.gov (United States)

    Lee, David C; Smith, Silas W; McStay, Christopher M; Portelli, Ian; Goldfrank, Lewis R; Husk, Gregg; Shah, Nirav R

    2014-04-09

    A freestanding, 911-receiving emergency department was implemented at Bellevue Hospital Center during the recovery efforts after Hurricane Sandy to compensate for the increased volume experienced at nearby hospitals. Because inpatient services at several hospitals remained closed for months, emergency volume increased significantly. Thus, in collaboration with the New York State Department of Health and other partners, the Health and Hospitals Corporation and Bellevue Hospital Center opened a freestanding emergency department without on-site inpatient care. The successful operation of this facility hinged on key partnerships with emergency medical services and nearby hospitals. Also essential was the establishment of an emergency critical care ward and a system to monitor emergency department utilization at affected hospitals. The results of this experience, we believe, can provide a model for future efforts to rebuild emergency care capacity after a natural disaster such as Hurricane Sandy. (Disaster Med Public Health Preparedness. 2014;0:1-4).

  12. Photon Shielding Features of Quarry Tuff

    Directory of Open Access Journals (Sweden)

    Vega-Carrillo Hector Rene

    2017-01-01

    Full Text Available Cantera is a quarry tuff widely used in the building industry; in this work the shielding features of cantera were determined. The shielding characteristics were calculated using XCOM and MCNP5 codes for 0.03, 0.07, 0.1, 0.3, 0.662, 1, 2, and 3 MeV photons. With XCOM the mass interaction coefficients, and the total mass attenuation coefficients, were calculated. With the MCNP5 code a transmission experiment was modelled using a point-like source located 42 cm apart from a point-like detector. Between the source and the detector, cantera pieces with different thickness, ranging from 0 to 40 cm were included. The collided and uncollided photon fluence, the Kerma in air and the Ambient dose equivalent were estimated. With the uncollided fluence the linear attenuation coefficients were determined and compared with those calculated with XCOM. The linear attenuation coefficient for 0.662 MeV photons was compared with the coefficient measured with a NaI(Tl-based γ-ray spectrometer and a 137Cs source.

  13. Soil compaction during harvest operations in five tropical soils with different textures under eucalyptus forests

    Directory of Open Access Journals (Sweden)

    Paula Cristina Caruana Martins

    Full Text Available ABSTRACT Traffic of farm machinery during harvest and logging operations has been identified as the main source of soil structure degradation in forestry activity. Soil susceptibility to compaction and the amount of compaction caused by each forest harvest operation differs according to a number of factors (such as soil strength, soil texture, kind of equipment, traffic intensity, among many others, what requires the adequate assessment of soil compaction under different traffic conditions. The objectives of this study were to determine the susceptibility to compaction of five soil classes with different textures under eucalyptus forests based on their load bearing capacity models; and to determine, from these models and the precompression stresses obtained after harvest operations, the effect of traffic intensity with different equipment in the occurrence of soil compaction. Undisturbed soil samples were collected before and after harvest operations, being then subjected to uniaxial compression tests to determine their precompression stress. The coarse-textured soils were less resistant and endured greater soil compaction. In the clayey LVd2, traffic intensity below four Forwarder passes limited compaction to a third of the samples, whereas in the sandy loam PVd all samples from the 0-3 cm layer were compacted regardless of traffic intensity. The Feller Buncher and the Clambunk presented a high potential to cause soil compaction even with only one or two passes. The use of soil load bearing capacity models and precompression stress determined after harvest and logging operations allowed insight into the soil compaction process in forestry soils.

  14. Numerical modeling of salt marsh morphological change induced by Hurricane Sandy

    Science.gov (United States)

    Hu, Kelin; Chen, Qin; Wang, Hongqing; Hartig, Ellen K.; Orton, Philip M.

    2018-01-01

    The salt marshes of Jamaica Bay serve as a recreational outlet for New York City residents, mitigate wave impacts during coastal storms, and provide habitat for critical wildlife species. Hurricanes have been recognized as one of the critical drivers of coastal wetland morphology due to their effects on hydrodynamics and sediment transport, deposition, and erosion processes. In this study, the Delft3D modeling suite was utilized to examine the effects of Hurricane Sandy (2012) on salt marsh morphology in Jamaica Bay. Observed marsh elevation change and accretion from rod Surface Elevation Tables and feldspar Marker Horizons (SET-MH) and hydrodynamic measurements during Hurricane Sandy were used to calibrate and validate the wind-waves-surge-sediment transport-morphology coupled model. The model results agreed well with in situ field measurements. The validated model was then used to detect salt marsh morphological change due to Sandy across Jamaica Bay. Model results indicate that the island-wide morphological changes in the bay's salt marshes due to Sandy were in the range of −30 mm (erosion) to +15 mm (deposition), and spatially complex and heterogeneous. The storm generated paired deposition and erosion patches at local scales. Salt marshes inside the west section of the bay showed erosion overall while marshes inside the east section showed deposition from Sandy. The net sediment amount that Sandy brought into the bay is only about 1% of the total amount of reworked sediment within the bay during the storm. Numerical experiments show that waves and vegetation played a critical role in sediment transport and associated wetland morphological change in Jamaica Bay. Furthermore, without the protection of vegetation, the marsh islands of Jamaica Bay would experience both more erosion and less accretion in coastal storms.

  15. New data towards the development of a comprehensive taphonomic framework for the Late Jurassic Cleveland-Lloyd Dinosaur Quarry, Central Utah

    Directory of Open Access Journals (Sweden)

    Joseph E. Peterson

    2017-06-01

    Full Text Available The Cleveland-Lloyd Dinosaur Quarry (CLDQ is the densest deposit of Jurassic theropod dinosaurs discovered to date. Unlike typical Jurassic bone deposits, it is dominated by the presence of Allosaurus fragilis. Since excavation began in the 1920s, numerous hypotheses have been put forward to explain the taphonomy of CLDQ, including a predator trap, a drought assemblage, and a poison spring. In an effort to reconcile the various interpretations of the quarry and reach a consensus on the depositional history of CLDQ, new data is required to develop a robust taphonomic framework congruent with all available data. Here we present two new data sets that aid in the development of such a robust taphonomic framework for CLDQ. First, x-ray fluorescence of CLDQ sediments indicate elevated barite and sulfide minerals relative to other sediments from the Morrison Formation in the region, suggesting an ephemeral environment dominated by periods of hypereutrophic conditions during bone accumulation. Second, the degree of abrasion and hydraulic equivalency of small bone fragments dispersed throughout the matrix were analyzed from CLDQ. Results of these analyses suggest that bone fragments are autochthonous or parautochthonous and are derived from bones deposited in the assemblage rather than transported. The variability in abrasion exhibited by the fragments is most parsimoniously explained by local periodic re-working and re-deposition during seasonal fluctuations throughout the duration of the quarry assemblage. Collectively, these data support previous interpretations that the CLDQ represents an attritional assemblage in a poorly-drained overbank deposit where vertebrate remains were introduced post-mortem to an ephemeral pond during flood conditions. Furthermore, while the elevated heavy metals detected at the Cleveland-Lloyd Dinosaur Quarry are not likely the primary driver for the accumulation of carcasses, they are likely the result of multiple sources

  16. Can porosity affect the hyperspectral signature of sandy landscapes?

    Science.gov (United States)

    Baranoski, Gladimir V. G.; Kimmel, Bradley W.

    2017-10-01

    Porosity is a fundamental property of sand deposits found in a wide range of landscapes, from beaches to dune fields. As a primary determinant of the density and permeability of sediments, it represents a central element in geophysical studies involving basin modeling and coastal erosion as well as geoaccoustics and geochemical investigations aiming at the understanding of sediment transport and water diffusion properties of sandy landscapes. These applications highlight the importance of obtaining reliable porosity estimations, which remains an elusive task, notably through remote sensing. In this work, we aim to contribute to the strengthening of the knowledge basis required for the development of new technologies for the remote monitoring of environmentally-triggered changes in sandy landscapes. Accordingly, we employ an in silico investigation approach to assess the effects of porosity variations on the reflectance of sandy landscapes in the visible and near-infrared spectral domains. More specifically, we perform predictive computer simulations using SPLITS, a hyperspectral light transport model for particulate materials that takes into account actual sand characterization data. To the best of our knowledge, this work represents the first comprehensive investigation relating porosity to the reflectance responses of sandy landscapes. Our findings indicate that the putative dependence of these responses on porosity may be considerably less pronounced than its dependence on other properties such as grain size and shape. Hence, future initiatives for the remote quantification of porosity will likely require reflectance sensors with a high degree of sensitivity.

  17. Online Media Use and Adoption by Hurricane Sandy Affected Fire and Police Departments

    OpenAIRE

    Chauhan, Apoorva

    2014-01-01

    In this thesis work, I examine the use and adoption of online communication media by 840 fire and police departments that were affected by the 2012 Hurricane Sandy. I began by exploring how and why these fire and police departments used (or did not use) online media to communicate with the public during Hurricane Sandy. Results show that fire and police departments used online media during Hurricane Sandy to give timely and relevant information to the public about things such as evacuations, ...

  18. Semantic attributes based texture generation

    Science.gov (United States)

    Chi, Huifang; Gan, Yanhai; Qi, Lin; Dong, Junyu; Madessa, Amanuel Hirpa

    2018-04-01

    Semantic attributes are commonly used for texture description. They can be used to describe the information of a texture, such as patterns, textons, distributions, brightness, and so on. Generally speaking, semantic attributes are more concrete descriptors than perceptual features. Therefore, it is practical to generate texture images from semantic attributes. In this paper, we propose to generate high-quality texture images from semantic attributes. Over the last two decades, several works have been done on texture synthesis and generation. Most of them focusing on example-based texture synthesis and procedural texture generation. Semantic attributes based texture generation still deserves more devotion. Gan et al. proposed a useful joint model for perception driven texture generation. However, perceptual features are nonobjective spatial statistics used by humans to distinguish different textures in pre-attentive situations. To give more describing information about texture appearance, semantic attributes which are more in line with human description habits are desired. In this paper, we use sigmoid cross entropy loss in an auxiliary model to provide enough information for a generator. Consequently, the discriminator is released from the relatively intractable mission of figuring out the joint distribution of condition vectors and samples. To demonstrate the validity of our method, we compare our method to Gan et al.'s method on generating textures by designing experiments on PTD and DTD. All experimental results show that our model can generate textures from semantic attributes.

  19. Heterotrophic bacterial populations in tropical sandy beaches

    Digital Repository Service at National Institute of Oceanography (India)

    Nair, S.; LokaBharathi, P.A.

    Distribution pattern of heterotrophic bacterial flora of three sandy beaches of the west coast of India was studied. The population in these beaches was microbiologically different. Population peaks of halotolerant and limnotolerant forms were...

  20. 2012 U.S. Geological Survey Topographic Lidar: Northeast Atlantic Coast Post-Hurricane Sandy

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Binary point-cloud data were produced for a portion of the New York, Delaware, Maryland, Virginia, and North Carolina coastlines, post-Hurricane Sandy (Sandy was an...

  1. Assessment of Environmental Impacts of Limestone Quarrying Operations in Thailand

    Directory of Open Access Journals (Sweden)

    Kittipongvises Suthirat

    2017-11-01

    Full Text Available Environmental impacts of the mineral extraction have been a public concern. Presently, there is widespread global interest in the area of mining and its sustainability that focused on the need to shift mining industry to a more sustainable framework. The aim of this study was to systematically assess all possible environmental and climate change related impacts of the limestone quarrying operation in Thailand. By considering the life cycle assessment method, the production processes were divided into three phases: raw material extraction, transportation, and comminution. Both IMPACT 2002+ and the Greenhouse Gas Protocol methods were used. Results of IMPACT 2002+ analysis showed that per 1 ton crushed limestone rock production, the total depletion of resource and GHGs emissions were 79.6 MJ and 2.76 kg CO2 eq., respectively. Regarding to the four damage categories, ‘resources’ and ‘climate change’ categories were the two greatest environmental impacts of the limestone rock production. Diesel fuel and electricity consumption in the mining processes were the main causes of those impacts. For climate change, the unit of CO2 eq. was expressed to quantify the total GHGs emissions. Estimated result was about 3.13 kg CO2 eq. per ton limestone rock product. The results obtained by the Greenhouse Gas Protocol were also similar to IMPACT 2002+ method. Electrical energy consumption was considered as the main driver of GHGs, accounting for approximately 46.8 % of total fossil fuel CO2 emissions. A final point should be noted that data uncertainties in environmental assessment over the complete life cycle of limestone quarrying operation have to be carefully considered.

  2. Characteristics of the quarry as shielding for {sup 241}AmBe neutrons and monoenergetic photons; Caracteristicas de la cantera como blindaje para los neutrones del {sup 241}AmBe y fotones monoenergeticos

    Energy Technology Data Exchange (ETDEWEB)

    Vega C, H. R.; Hernandez D, V. M.; Letechipia de L, C.; Salas L, M. A. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico); Rodriguez R, J. A.; Juarez A, C. A., E-mail: fermineutron@yahoo.com [Universidad Autonoma de Nuevo Leon, Facultad de Ingenieria Civil, Pedro de Alba s/n, San Nicolas de los Garza, Nuevo Leon (Mexico)

    2016-09-15

    Shielding is an important element in radiation protection since allows the management of radiation sources. Currently there are different materials of natural or anthropogenic origin that are used as shielding for both photons and neutrons. The quarry is a material of natural origin and abundant in our country, which is used in construction or for the manufacture of sculptures, however its characteristics as shielding have not been reported. In this paper we report some of the properties of the quarry as shielding for monoenergetic photons and for neutrons produced by an isotopic neutron source of {sup 241}AmBe. A quarry piece was used to determine its density and its chemical composition, with the XCOM code the elemental composition was determined and the mass interaction and total attenuation coefficients of the quarry were determined with photons of 10{sup -3} to 10{sup -5} MeV; the interaction coefficients included coherent dispersion, photoelectric absorption, Compton dispersion and the production of pairs in the nuclear and electronic field. Using the MCNP5 code, a narrow geometry attenuation experiment was modeled and the photon fluence was estimated that reaches a point detector at a distance of 42 cm from a point source, isotropic and monoenergetic photon when the source and the point detector were added quarry pieces of different thicknesses. The reduction of the number of photons as a function of the thickness of the quarry was used to determine the coefficient of linear attenuation of the quarry before photons of 0.03, 0.07, 0.1, 0.3, 1, 2 and 3 MeV that were the same as those calculated with the XCOM code. With the MCNP, the K a and H(10) transmission curves were also calculated. This same model was used to determined the variation of the {sup 241}AmBe neutron spectrum as a function of quarry thickness, as well as the E{sub ROT} and H(10) transmission curves. (Author)

  3. Microbial community dynamics and transformation of vascular plant detritus in two wetland ecosystems

    International Nuclear Information System (INIS)

    Moran, M.A.

    1987-01-01

    The microbial ecology of two wetland ecosystems in southeastern Georgia, USA, was studied with respect to microbial community dynamics and microbially-mediated transformations of vascular plant detritus. In the Okefenokee Swamp, biomass of microorganisms in the water column and sediments was generally lower in winter months and higher during spring and summer. Biomass and activity (measured as 14 C-lignocellulose mineralization) differed significantly among five habitats within the Okefenokee, and also among locations within each habitat. Significant heterogeneity in the structure of Okefenokee microbial communities was found at scales from 30 cm to 150 m. In field and laboratory studies of vascular plant decomposition in the Okefenokee and a salt marsh on Sapelo Island, the mathematical model which best describes decomposition kinetics is the decaying coefficient model

  4. Biofouling of granite-rapakivi in St. Petersburg monuments and in the quarry in Russia and Finland

    Science.gov (United States)

    Vlasov, Dmitry; Panova, Elena; Alampieva, Elena; Olhovaya, Elena; Popova, Tatyana; Vlasov, Alexey; Zelenskaya, Marina

    2013-04-01

    Granite-rapakivi was widely used in the architecture of St. Petersburg: the facades of buildings, embankments of rivers and canals, bridges, sculptural monuments, pedestals, facing the metro stations. This stone is rapidly destroyed due to the peculiarities of its structure. Biofouling of granite is insufficiently studied. Cause the destruction of granite can be bacteria, microscopic algae, fungi, mosses, lichens, higher plants, invertebrates and vertebrates. They often form specific lithobiotic communities that contribute to the destruction of granite-rapakivi. The objects of research were monuments of St. Petersburg (granite sculpture, facades, facing embankments) as well as granite-rapakivi quarries in Russia and Finland, where the stone was quarried for use in St. Petersburg. Sampling was carried out from the most typical biofouling sites. Different methods were applied for the study of damaged granite: petrographic analysis, light and scanning electron microscopy, methods for detection and identification of microorganisms, X-ray microprobe analysis. As result the main forms of granite destruction were described: fractures, ovoid weathering, granular disintegration, surface films, crusts and layers, pitting and fouling. Lichens, mosses, herbaceous and micromycetes were dominated on the granite-rapakivi in quarries. For example, in a Monferran quarry (Virolahti region) the complicated lithobiotic community was revealed. It included 30 species of micromycetes, 31 species of lichens, 10 species of moss. Bacteriological analysis showed the dominance of bacteria Bacillus, and actinomycetes in microbial biofilms. More than 100 species of plants were found on the granite embankments in St. Petersburg. They were confined to the cracks, seams of granite blocks. Plants and mosses were common to the granite embankments of rivers and canals in the central (historical) part of the city. Dimensions of mosses depend on the area of the deepening which they occupy. The most

  5. The need for sustainable technology diffusion in mining: Achieving the use of belt conveyor systems in the German hard-rock quarrying industry

    Directory of Open Access Journals (Sweden)

    Tobias Braun

    2017-01-01

    Full Text Available The movement of raw materials can be one of the most challenging tasks in open pit mining, with truck transportation representing the largest factor in mining costs and resulting in major greenhouse gas (GHG emissions. In this study, the transportation methods of bulk materials within German hard-rock open pit mines were investigated. Approximately 450 quarries were studied for their production tonnage, lease areas, mined rock type as well as mining methods and processing equipment. The results demonstrate that 90% of the operations use truck-based transportation methods, with the remainder relying partly or completely on continuous conveyor-based systems. The installation of continuous conveyors compared to trucks represents a real alternative because of reduced dead load, reduced GHG emissions and in many cases even reduced costs. Thus, for in-pit haulage in quarries sustainable technology substitutions exist that are yet to be adopted by the German quarrying industry. As this study shows, in the future the diffusion of sustainable technologies requires site champions and large-scale case studies that demonstrate their successful introduction in the mining value chain.

  6. Analysis of conditions and the concept of multidirectional revitalization of the dolomite quarry in Siewierz

    Science.gov (United States)

    Pawełczyk, Katarzyna

    2018-01-01

    The development of mining of rock raw materials in Poland has significantly contributed to economic growth and the quality of life of local communities. However, mining activity, besides a number of positive effects, also implies broadly understood changes in the environment and the formation of brownfields. Reclamation and redevelopment of post-industrial areas, and especially post-mining areas, is currently a huge environmental and socio-economic challenge. Revitalization of post-mining areas is particularly important for small towns and municipalities, where mining was one of the main pillars of development and prosperity. An example of such a municipality is Siewierz in Silesian Voivodship. In the paper analysis the conditions have been conducted and the concept of revitalization of dolomite quarry Górnicze Zakłady Dolomitowe S.A. has been proposed. The AHP method has been used to analyse and select the optimal method of revitalization. As a result of the analysis, the concept of multidirectional revitalization with socially, economically and environmentally beneficial functions has been created, maximizing the potential of the quarry.

  7. Regional analysis of groundwater phosphate concentrations under acidic sandy soils: Edaphic factors and water table strongly mediate the soil P-groundwater P relation.

    Science.gov (United States)

    Mabilde, Lisa; De Neve, Stefaan; Sleutel, Steven

    2017-12-01

    Historic long-term P application to sandy soils in NW-Europe has resulted in abundant sorption, saturation and eventually leaching of P from soil to the groundwater. Although many studies recognize the control of site-specific factors like soil texture and phosphate saturation degree (PSD), the regional-scaled relevance of effects exerted by single factors controlling P leaching is unclear. Very large observational datasets of soil and groundwater P content are furthermore required to reveal indirect controls of soil traits through mediating soil variables. We explored co-variation of phreatic groundwater orthophosphate (o-P) concentration and soil factors in sandy soils in Flanders, Belgium. Correlation analyses were complemented with an exploratory model derived using 'path analysis'. Data of oxalate-extractable Al, Fe, P and pH KCl , phosphate sorption capacity (PSC) and PSD in three depth layers (0-30, 30-60, 60-90 cm), topsoil SOC, % clay and groundwater depth (fluctuation) were interpolated to predict soil properties on exact locations of a very extensive net of groundwater monitoring wells. The mean PSD was only poorly correlated to groundwater o-P concentration, indicating the overriding control of other factors in the transport of P to the groundwater. A significant (P soil pH and groundwater table depth than by PSD indicates the likely oversimplification of the latter index to measure the long-term potential risk of P leaching. Accounting for controls on leaching not included in PSD via an alternative index, however, seems problematic as in Flanders for example groundwater o-P turned out to be higher in finer textured soils or soils with higher pedogenic Fe content, probably because of their lower pedogenic Al content and higher soil pH. Path analysis of extensive soil and groundwater datasets seems a viable way to identify prime local determinants of soil P leaching and could be further on used for 'ground-truthing' more complex P-migration simulation

  8. Measurement of biological oxygen demand sandy beaches

    African Journals Online (AJOL)

    Measurements of biological oxygen demand in a sandy beach using conventional .... counting the cells present in a sample of aged seawater and comparing this with .... This activity peaked at 71 % above the undisturbed level after 16 hours.

  9. Lithuanian Quarry Aggregates Concrete Effects of Alkaline Corrosion Tests

    Directory of Open Access Journals (Sweden)

    Aurimas Rutkauskas

    2016-02-01

    Full Text Available Aggregate alkaline corrosion of cement in concrete is going to respond in sodium and potassium hydroxide (lye with active SiO2 found in some aggregates. During this reaction, the concrete has resulted in significant internal stresses which cause deformation of the concrete, cracking and disintegration. The reaction is slow and concrete signs of decomposition appear only after a few months or years. The study used two different aggregates quarries. Studies show that Lithuania gravel contaminated with reactive particles having amorphous silicon dioxide reacting with cement in sodium and potassium hydroxide and the resulting alkaline concrete corrosion. It was found that, according to AAR 2 large aggregates include Group II – potentially reactive because of their expansion after 14 days, higher than 0.1%.

  10. Application of the chain saw machine for underground quarry

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Han-Uk; Baek, Hwan-Jo [Kangwon National University, Chuncheon(Korea); Kim, Chi-Hwan [Woosuk University, Wonju(Korea); Kim, Tae-Soo [Sungshin Mining Co., Jungseun(Korea)

    2001-10-31

    Many regulatory activities for preservation of the environment make it recently difficult for the stone industry in our country. To reduce environmental hazards and to conserve original surface and woods, some effective underground methods must be adopted. Some new techniques such as chain saw machine, diamond wire saw and water jet cutting can be considered. But application of chain saw machine for underground quarry is proposed in this study. Some technical adoptions with chain saw were carried out at Jungseun marble mine. It is proved that this machine can be effectively adopted to cut dimension stone. With chain saw and diamond wire saw, it can be expected to achieve more effectively cutting the dimension stone. (author). 6 refs., 3 tabs., 6 figs.

  11. Visual Analysis as a design and decision-making tool in the development of a quarry

    Science.gov (United States)

    Randall Boyd Fitzgerald

    1979-01-01

    In order to obtain local and state government approvals, an environmental impact analysis of the mining and reclamation of a proposed hard rock quarry was required. High visibility of the proposed mining area from the adjacent community required a visual impact analysis in the planning and design of the project. The Visual Analysis defined design criteria for the...

  12. Aesthetic Perception of Visual Textures: A Holistic Exploration using Texture Analysis, Psychological Experiment and Perception Modeling

    Directory of Open Access Journals (Sweden)

    Jianli eLiu

    2015-11-01

    Full Text Available Modeling human aesthetic perception of visual textures is important and valuable in numerous industrial domains, such as product design, architectural design and decoration. Based on results from a semantic differential rating experiment, we modeled the relationship between low-level basic texture features and aesthetic properties involved in human aesthetic texture perception. First, we compute basic texture features from textural images using four classical methods. These features are neutral, objective and independent of the socio-cultural context of the visual textures. Then, we conduct a semantic differential rating experiment to collect from evaluators their aesthetic perceptions of selected textural stimuli. In semantic differential rating experiment, eights pairs of aesthetic properties are chosen, which are strongly related to the socio-cultural context of the selected textures and to human emotions. They are easily understood and connected to everyday life. We propose a hierarchical feed-forward layer model of aesthetic texture perception and assign 8 pairs of aesthetic properties to different layers. Finally, we describe the generation of multiple linear and nonlinear regression models for aesthetic prediction by taking dimensionality-reduced texture features and aesthetic properties of visual textures as dependent and independent variables, respectively. Our experimental results indicate that the relationships between each layer and its neighbors in the hierarchical feed-forward layer model of aesthetic texture perception can be fitted well by linear functions, and the models thus generated can successfully bridge the gap between computational texture features and aesthetic texture properties.

  13. [Visual Texture Agnosia in Humans].

    Science.gov (United States)

    Suzuki, Kyoko

    2015-06-01

    Visual object recognition requires the processing of both geometric and surface properties. Patients with occipital lesions may have visual agnosia, which is impairment in the recognition and identification of visually presented objects primarily through their geometric features. An analogous condition involving the failure to recognize an object by its texture may exist, which can be called visual texture agnosia. Here we present two cases with visual texture agnosia. Case 1 had left homonymous hemianopia and right upper quadrantanopia, along with achromatopsia, prosopagnosia, and texture agnosia, because of damage to his left ventromedial occipitotemporal cortex and right lateral occipito-temporo-parietal cortex due to multiple cerebral embolisms. Although he showed difficulty matching and naming textures of real materials, he could readily name visually presented objects by their contours. Case 2 had right lower quadrantanopia, along with impairment in stereopsis and recognition of texture in 2D images, because of subcortical hemorrhage in the left occipitotemporal region. He failed to recognize shapes based on texture information, whereas shape recognition based on contours was well preserved. Our findings, along with those of three reported cases with texture agnosia, indicate that there are separate channels for processing texture, color, and geometric features, and that the regions around the left collateral sulcus are crucial for texture processing.

  14. Parallel-Sequential Texture Analysis

    NARCIS (Netherlands)

    van den Broek, Egon; Singh, Sameer; Singh, Maneesha; van Rikxoort, Eva M.; Apte, Chid; Perner, Petra

    2005-01-01

    Color induced texture analysis is explored, using two texture analysis techniques: the co-occurrence matrix and the color correlogram as well as color histograms. Several quantization schemes for six color spaces and the human-based 11 color quantization scheme have been applied. The VisTex texture

  15. Feature-aware natural texture synthesis

    KAUST Repository

    Wu, Fuzhang

    2014-12-04

    This article presents a framework for natural texture synthesis and processing. This framework is motivated by the observation that given examples captured in natural scene, texture synthesis addresses a critical problem, namely, that synthesis quality can be affected adversely if the texture elements in an example display spatially varied patterns, such as perspective distortion, the composition of different sub-textures, and variations in global color pattern as a result of complex illumination. This issue is common in natural textures and is a fundamental challenge for previously developed methods. Thus, we address it from a feature point of view and propose a feature-aware approach to synthesize natural textures. The synthesis process is guided by a feature map that represents the visual characteristics of the input texture. Moreover, we present a novel adaptive initialization algorithm that can effectively avoid the repeat and verbatim copying artifacts. Our approach improves texture synthesis in many images that cannot be handled effectively with traditional technologies.

  16. FCC Rolling Textures Reviewed in the Light of Quantitative Comparisons between Simulated and Experimental Textures

    DEFF Research Database (Denmark)

    Wierzbanowski, Krzysztof; Wroński, Marcin; Leffers, Torben

    2014-01-01

    The crystallographic texture of metallic materials has a very strong effect on the properties of the materials. In the present article, we look at the rolling textures of fcc metals and alloys, where the classical problem is the existence of two different types of texture, the "copper-type texture......" and the "brass-type texture." The type of texture developed is determined by the stacking fault energy of the material, the rolling temperature and the strain rate of the rolling process. Recent texture simulations by the present authors provide the basis for a renewed discussion of the whole field of fcc......} slip without or with deformation twinning, but we also consider slip on other slip planes and slip by partial dislocations. We consistently make quantitative comparison of the simulation results and the experimental textures by means of a scalar correlation factor. We find that the development...

  17. Coqui frog populations are negatively affected by canopy opening but not detritus deposition following an experimental hurricane in a tropical rainforest

    Science.gov (United States)

    Paul D. Klawanski; Ben Dalton; Aaron B. Shiels

    2014-01-01

    Hurricanes, cyclones, and typhoons are common disturbances in many island and coastal forests. There is a lack of understanding of the importance to forest biota of the two major physical aspects that occur simultaneously during a hurricane: canopy disturbance and detritus (debris) deposition onto the ground. Using a replicated factorial design, our study involved...

  18. The role of wrack deposits for supralittoral arthropods: An example using Atlantic sandy beaches of Brazil and Spain

    Science.gov (United States)

    Ruiz-Delgado, Mª Carmen; Vieira, Jenyffer Vierheller; Veloso, Valéria Gomes; Reyes-Martínez, Mª José; Sallorenzo, Ilana Azevedo; Borzone, Carlos Alberto; Sánchez-Moyano, Juan Emilio; García García, Francisco José

    2014-01-01

    Wrack deposits, as accumulated detritus, are a common feature on beaches worldwide and significantly contribute to the shaping of supralittoral arthropod communities. The composition and relative age of upper-shore deposits influence the structure and taxonomic composition of invertebrate assemblages. Moreover, these influences may vary geographically, depending on the locally prevailing climatic and hydrodynamic conditions. The amount and composition of wrack deposits as well as community attributes (total density, species richness and diversity) were determined on sandy beaches in three distinct geographical regions: South (Paraná) and Southeast (Rio de Janeiro) of Brazil and SW Spain. These parameters were compared between upper and lower wrack bands on each beach and between beaches in each region. Wrack deposits were composed of mangrove propagules in the Paraná region, by macrophytes, dead invertebrates and macroalgae in Rio de Janeiro region and by seagrass and macroalgae in the SW Spain region. In all regions, the total amount of stranded wrack differed between beaches, but the amount accumulated between bands (i.e upper and lower band) was similar between beaches. Wrack bands shaped the density of common taxa (Talitridae, Tenebrionidae, and Staphylinidae), with consequences for community structures. This result could be due to their preference for specific microhabitats and food sources, which might differ according to the relative age of the wrack deposits. The results suggest that, independent of wrack composition, the distribution of wrack deposits in bands and their relative ages seems to play a role on the structure of supralittoral arthropod assemblages.

  19. Seismic texture classification. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Vinther, R.

    1997-12-31

    The seismic texture classification method, is a seismic attribute that can both recognize the general reflectivity styles and locate variations from these. The seismic texture classification performs a statistic analysis for the seismic section (or volume) aiming at describing the reflectivity. Based on a set of reference reflectivities the seismic textures are classified. The result of the seismic texture classification is a display of seismic texture categories showing both the styles of reflectivity from the reference set and interpolations and extrapolations from these. The display is interpreted as statistical variations in the seismic data. The seismic texture classification is applied to seismic sections and volumes from the Danish North Sea representing both horizontal stratifications and salt diapers. The attribute succeeded in recognizing both general structure of successions and variations from these. Also, the seismic texture classification is not only able to display variations in prospective areas (1-7 sec. TWT) but can also be applied to deep seismic sections. The seismic texture classification is tested on a deep reflection seismic section (13-18 sec. TWT) from the Baltic Sea. Applied to this section the seismic texture classification succeeded in locating the Moho, which could not be located using conventional interpretation tools. The seismic texture classification is a seismic attribute which can display general reflectivity styles and deviations from these and enhance variations not found by conventional interpretation tools. (LN)

  20. Epidemic gasoline exposures following Hurricane Sandy.

    Science.gov (United States)

    Kim, Hong K; Takematsu, Mai; Biary, Rana; Williams, Nicholas; Hoffman, Robert S; Smith, Silas W

    2013-12-01

    Major adverse climatic events (MACEs) in heavily-populated areas can inflict severe damage to infrastructure, disrupting essential municipal and commercial services. Compromised health care delivery systems and limited utilities such as electricity, heating, potable water, sanitation, and housing, place populations in disaster areas at risk of toxic exposures. Hurricane Sandy made landfall on October 29, 2012 and caused severe infrastructure damage in heavily-populated areas. The prolonged electrical outage and damage to oil refineries caused a gasoline shortage and rationing unseen in the USA since the 1970s. This study explored gasoline exposures and clinical outcomes in the aftermath of Hurricane Sandy. Prospectively collected, regional poison control center (PCC) data regarding gasoline exposure cases from October 29, 2012 (hurricane landfall) through November 28, 2012 were reviewed and compared to the previous four years. The trends of gasoline exposures, exposure type, severity of clinical outcome, and hospital referral rates were assessed. Two-hundred and eighty-three gasoline exposures were identified, representing an 18 to 283-fold increase over the previous four years. The leading exposure route was siphoning (53.4%). Men comprised 83.0% of exposures; 91.9% were older than 20 years of age. Of 273 home-based calls, 88.7% were managed on site. Asymptomatic exposures occurred in 61.5% of the cases. However, minor and moderate toxic effects occurred in 12.4% and 3.5% of cases, respectively. Gastrointestinal (24.4%) and pulmonary (8.4%) symptoms predominated. No major outcomes or deaths were reported. Hurricane Sandy significantly increased gasoline exposures. While the majority of exposures were managed at home with minimum clinical toxicity, some patients experienced more severe symptoms. Disaster plans should incorporate public health messaging and regional PCCs for public health promotion and toxicological surveillance.

  1. Ecotoxicological risk assessment linked to infilling quarries with treated dredged seaport sediments

    Energy Technology Data Exchange (ETDEWEB)

    Perrodin, Yves, E-mail: perrodin@entpe.fr [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Donguy, Gilles [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Bazin, Christine [INSAVALOR, 20 avenue Albert Einstein, 69621 Villeurbanne Cedex (France); Volatier, Laurence; Durrieu, Claude [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Bony, Sylvie; Devaux, Alain [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); INRA, USC IGH, UMR LEHNA, 2, rue Maurice Audin, 69518 Vaulx-en-Velin (France); Abdelghafour, Mohammed; Moretto, Robert [INSAVALOR, 20 avenue Albert Einstein, 69621 Villeurbanne Cedex (France)

    2012-08-01

    The dredged sediments of polluted seaports now raise complex management problems since it is no longer possible to discharge them into the sea. This results in the need to manage them on land, raising other types of technical, economic and environmental problems. Regarding the technical and economic dimensions, traditional waste treatment methods have proved to be poorly adapted, due to very high costs and low absorbable volumes. In this context, filling quarries in coastal areas with treated sediments could represent an interesting alternative for these materials. Nevertheless, for the environmental dimension, it is necessary to demonstrate that this possibility is harmless to inland ecosystems. Consequently, a specific ecotoxicological risk assessment methodology has been formulated and tested on three sediments taken from seaboards of France, in view to providing an operational and usable tool for the prior validation of any operation to fill quarries with treated seaport sediments. This method incorporates the formulation of a global conceptual model of the scenario studied and the definition of protocols for each of its steps: the characterisation of exposures (based on a simulation of sediment deposit), the characterisation of effects (via the study of sediments ecotoxicity), and the final ecotoxicological risk assessment performed as a calculation of a risk quotient. It includes the implementation in parallel of two types of complementary approach: the 'substances' approach derived from the European methodology for assessing new substances placed on the market, and the 'matrix' approach which is similar to methods developed in France to assess ecological risks in other domains (waste management, polluted site management, Horizontal-Ellipsis ). The application of this dual approach to the three sediments tested led to conclude with reliability that the project to deposit sediments '1' and '2' presented a low risk for

  2. Ecotoxicological risk assessment linked to infilling quarries with treated dredged seaport sediments

    International Nuclear Information System (INIS)

    Perrodin, Yves; Donguy, Gilles; Bazin, Christine; Volatier, Laurence; Durrieu, Claude; Bony, Sylvie; Devaux, Alain; Abdelghafour, Mohammed; Moretto, Robert

    2012-01-01

    The dredged sediments of polluted seaports now raise complex management problems since it is no longer possible to discharge them into the sea. This results in the need to manage them on land, raising other types of technical, economic and environmental problems. Regarding the technical and economic dimensions, traditional waste treatment methods have proved to be poorly adapted, due to very high costs and low absorbable volumes. In this context, filling quarries in coastal areas with treated sediments could represent an interesting alternative for these materials. Nevertheless, for the environmental dimension, it is necessary to demonstrate that this possibility is harmless to inland ecosystems. Consequently, a specific ecotoxicological risk assessment methodology has been formulated and tested on three sediments taken from seaboards of France, in view to providing an operational and usable tool for the prior validation of any operation to fill quarries with treated seaport sediments. This method incorporates the formulation of a global conceptual model of the scenario studied and the definition of protocols for each of its steps: the characterisation of exposures (based on a simulation of sediment deposit), the characterisation of effects (via the study of sediments ecotoxicity), and the final ecotoxicological risk assessment performed as a calculation of a risk quotient. It includes the implementation in parallel of two types of complementary approach: the “substances” approach derived from the European methodology for assessing new substances placed on the market, and the “matrix” approach which is similar to methods developed in France to assess ecological risks in other domains (waste management, polluted site management, …). The application of this dual approach to the three sediments tested led to conclude with reliability that the project to deposit sediments “1” and “2” presented a low risk for the peripheral aquatic ecosystems while

  3. Methods of making textured catalysts

    Science.gov (United States)

    Werpy, Todd [West Richland, WA; Frye, Jr., John G.; Wang, Yong [Richland, WA; Zacher, Alan H [Kennewick, WA

    2010-08-17

    A textured catalyst having a hydrothermally-stable support, a metal oxide and a catalyst component is described. Methods of conducting aqueous phase reactions that are catalyzed by a textured catalyst are also described. The invention also provides methods of making textured catalysts and methods of making chemical products using a textured catalyst.

  4. Dilatometry study of textures

    International Nuclear Information System (INIS)

    Sofrenovic, R.; Lazarevic, Dj.

    1965-01-01

    Presence of textures in the metal uranium fuel is harmful because of anisotropy properties of uranium during thermal treatment, and especially during irradiation. Anisotropic radiation swelling of uranium can cause deformation of fuel element due to existence of textures. The objective of this work was studying of the influence of phase transformations on textures in uranium which has undergone plastic deformation due to rotational casting. Dilatometry method was adopted for testing the textures. This report describes the device for dilatometry testing and the measured preliminary results are shown

  5. 78 FR 7780 - Sunshine Act Meeting; FCC Announces Further Details for the First Post-Superstorm Sandy Field...

    Science.gov (United States)

    2013-02-04

    ... First Post-Superstorm Sandy Field Hearing, Tuesday, February 5, 2013 AGENCY: Federal Communications Commission. ACTION: Sunshine notice. SUMMARY: In the wake of Superstorm Sandy, Federal Communications... focusing on the impact of Superstorm Sandy, and help inform recommendations and actions to strengthen wired...

  6. Micro-Texture Synthesis by Phase Randomization

    Directory of Open Access Journals (Sweden)

    Bruno Galerne

    2011-09-01

    Full Text Available This contribution is concerned with texture synthesis by example, the process of generating new texture images from a given sample. The Random Phase Noise algorithm presented here synthesizes a texture from an original image by simply randomizing its Fourier phase. It is able to reproduce textures which are characterized by their Fourier modulus, namely the random phase textures (or micro-textures.

  7. Effective Fragmentation and Flyrock Control Strategies at Quarries

    Directory of Open Access Journals (Sweden)

    Sedat Esen

    2017-01-01

    Full Text Available This paper presents the effective fragmentation and flyrock control strategies that could be applied at quarries to improve the productivity and safety. Fragmentation measurement and modelling as well as a comprehensive drill and blast audit are essential for improving the fragmentation. Face profiling and bore tracking are good tools to manage the ―as-designed‖ and ―as-drilled‖ conditions to get reasonable fragmentation from face burden zone and minimise the flyrock risk. In general, a large scatter in fragmentation data was observed at sites and the causes should be analysed by a detailed root-cause analysis technique. Two case studies were presented in this paper showing some of the effective fragmentation strategies. Finally, a flyrock model was shown to determine the safe blast exclusion zone for the mining equipment and personnel. Some key guidelines were suggested to minimise the occurrence of the flyrock.

  8. Near-real-time Forensic Disaster Analysis: experiences from hurricane Sandy

    Science.gov (United States)

    Kunz, Michael; Mühr, Bernhard; Schröter, Kai; Kunz-Plapp, Tina; Daniell, James; Khazai, Bijan; Wenzel, Friedemann; Vannieuwenhuyse, Marjorie; Comes, Tina; Münzberg, Thomas; Elmer, Florian; Fohringer, Joachim; Lucas, Christian; Trieselmann, Werner; Zschau, Jochen

    2013-04-01

    Hurricane Sandy was the last tropical cyclone of the 2012 Northern Atlantic Hurricane season that made landfall. It moved on an unusual track from the Caribbean to the East Coast of the United States from 24 to 30 October as a Category 1 and 2 Hurricane according to the Saffir-Simpson Scale. Along its path, the severe storm event caused widespread damage including almost 200 fatalities. In the early hours of 30 October, Sandy made landfall near Atlantic City, N.J. Sandy was an extraordinary event due to its multihazard nature and several cascading effects in the aftermath. From the hydro-meteorological perspective, most unusual was the very large spatial extent of up to 1,700 km. High wind speeds were associated with record breaking storm surges at the U.S. Mid- Atlantic and New England Coast during high (astronomical) tide, leading to widespread flooding. Though Sandy was not the most severe storm event in terms of wind speed and precipitation, the impact in the U.S. was enormous with total damage estimates of up to 90 billion US (own estimate from Dec. 2012). Although much better data emerge weeks after such an event, the Forensic Disaster Analysis (FDA) Task Force of the Center for Disaster Management and Risk Reduction Technology (CEDIM) made an effort to obtain a comprehensive and holistic overview of the causes, hazardous effects and consequences associated with Sandy immediately after landfall at the U.S. coast on 30 October 2012. This was done in an interdisciplinary way by collecting and compiling scattered and distributed information from available databases and sources via the Internet, by applying own methodologies and models for near-real time analyses developed in recent years, and by expert knowledge. This contribution gives an overview about the CEDIM-FDA analyses' results. It describes the situation that led to the extraordinary event, highlights the interaction of the tropical cyclone with other hydro-meteorological events, and examines the

  9. The effect of vegetation and soil texture on the nature of organics in runoff from a catchment supplying water for domestic consumption

    Energy Technology Data Exchange (ETDEWEB)

    Awad, John [Centre for Water Management and Reuse, School of Natural and Built Environments, University of South Australia, South Australia 5095 (Australia); Leeuwen, John van, E-mail: John.VanLeeuwen@unisa.edu.au [Centre for Water Management and Reuse, School of Natural and Built Environments, University of South Australia, South Australia 5095 (Australia); State Key Laboratory for Environmental Aquatic Chemistry, CAS, Beijing (China); Barbara Hardy Institute, University of South Australia, South Australia 5095 (Australia); Abate, Dawit [Centre for Water Management and Reuse, School of Natural and Built Environments, University of South Australia, South Australia 5095 (Australia); Pichler, Markus; Bestland, Erick [School of the Environment, Flinders University, Bedford Park, South Australia 5042 (Australia); Chittleborough, David J. [School of Physical Sciences, University of Adelaide, North Terrace, South Australia 5005 (Australia); Fleming, Nigel [South Australian Research and Development Institute, P.O. Box 397, Adelaide, SA 5000 (Australia); Cohen, Jonathan; Liffner, Joel [Centre for Water Management and Reuse, School of Natural and Built Environments, University of South Australia, South Australia 5095 (Australia); Drikas, Mary [Centre for Water Management and Reuse, School of Natural and Built Environments, University of South Australia, South Australia 5095 (Australia); Australian Water Quality Centre, SA Water Corporation, 250 Victoria Square, Adelaide, South Australia 5000 (Australia); State Key Laboratory for Environmental Aquatic Chemistry, CAS, Beijing (China)

    2015-10-01

    The influence of vegetation and soil texture on the concentration and character of dissolved organic matter (DOM) present in runoff from the surface and sub-surface of zero order catchments of the Myponga Reservoir-catchment (South Australia) was investigated to determine the impacts of catchment characteristics and land management practices on the quality of waters used for domestic supply. Catchments selected have distinct vegetative cover (grass, native vegetation or pine) and contrasting texture of the surface soil horizon (sand or clay loam/clay). Water samples were collected from three slope positions (upper, middle, and lower) at soil depths of ~ 30 cm and ~ 60 cm in addition to overland flows. Filtered (0.45 μm) water samples were analyzed for dissolved organic carbon (DOC) and UV–visible absorbance and by F-EEM and HPSEC with UV and fluorescence detection to characterize the DOM. Surface and sub-surface runoff from catchments with clay soils and native vegetation or grass had lower DOC concentrations and lower relative abundances of aromatic, humic-like and high molecular weight organics than runoff from sandy soils with these vegetative types. Sub-surface flows from two catchments with Pinus radiata had similar DOC concentrations and DOM character, regardless of marked variation in surface soil texture. Runoff from catchments under native vegetation and grass on clay soils resulted in lower DOC concentrations and hence would be expected to have lower coagulant demand in conventional treatment for potable water supply than runoff from corresponding sandy soil catchments. However, organics in runoff from clay catchments would be more difficult to remove by coagulation. Surface waters from the native vegetation and grass catchments were generally found to have higher relative abundance of organic compounds amenable to removal by coagulation compared with sub-surface waters. Biophysical and land management practices combine to have a marked influence on

  10. The effect of vegetation and soil texture on the nature of organics in runoff from a catchment supplying water for domestic consumption

    International Nuclear Information System (INIS)

    Awad, John; Leeuwen, John van; Abate, Dawit; Pichler, Markus; Bestland, Erick; Chittleborough, David J.; Fleming, Nigel; Cohen, Jonathan; Liffner, Joel; Drikas, Mary

    2015-01-01

    The influence of vegetation and soil texture on the concentration and character of dissolved organic matter (DOM) present in runoff from the surface and sub-surface of zero order catchments of the Myponga Reservoir-catchment (South Australia) was investigated to determine the impacts of catchment characteristics and land management practices on the quality of waters used for domestic supply. Catchments selected have distinct vegetative cover (grass, native vegetation or pine) and contrasting texture of the surface soil horizon (sand or clay loam/clay). Water samples were collected from three slope positions (upper, middle, and lower) at soil depths of ~ 30 cm and ~ 60 cm in addition to overland flows. Filtered (0.45 μm) water samples were analyzed for dissolved organic carbon (DOC) and UV–visible absorbance and by F-EEM and HPSEC with UV and fluorescence detection to characterize the DOM. Surface and sub-surface runoff from catchments with clay soils and native vegetation or grass had lower DOC concentrations and lower relative abundances of aromatic, humic-like and high molecular weight organics than runoff from sandy soils with these vegetative types. Sub-surface flows from two catchments with Pinus radiata had similar DOC concentrations and DOM character, regardless of marked variation in surface soil texture. Runoff from catchments under native vegetation and grass on clay soils resulted in lower DOC concentrations and hence would be expected to have lower coagulant demand in conventional treatment for potable water supply than runoff from corresponding sandy soil catchments. However, organics in runoff from clay catchments would be more difficult to remove by coagulation. Surface waters from the native vegetation and grass catchments were generally found to have higher relative abundance of organic compounds amenable to removal by coagulation compared with sub-surface waters. Biophysical and land management practices combine to have a marked influence on

  11. Response of detritus food web and litter quality to elevated CO2 and crop cultivars and their feedback to soil functionality

    Science.gov (United States)

    Hu, Zhengkun; Chen, Xiaoyun; Zhu, Chunwu; Bonkowski, Michael; Hu, Shuijin; Li, Huixin; Hu, Feng; Liu, Manqiang

    2017-04-01

    Elevated atmospheric CO2 concentrations (eCO2) often increase plant growth and alter the belowground detritus soil food web. Interactions with agriculture management may further modify soil process and the associated ecosystem functionality. Little attention, however, has been directed toward assessing the responses of soil food web and their feedback to soil functionality, particularly in wetland agroecosystems. We report results from a long-term free air CO2 enrichment (FACE) experiment in a rice paddy field that examined the responses of detritus food webs to eCO2 (200 ppm higher than ambient CO2 (aCO2)) of two rice cultivars with distinctly weak and strong responses to eCO2. Soil detritus food web components, including soil microbes and microfauna, soil environment as well as resources availability variables, were determined at the rice ripening stage. To obtain the information of soil functionality, indicated by litter decomposition and enzyme activities, we adopted a reciprocal transplant approach that fully manipulate the factors of litter straw and food web components for the incubation of 120 days. Results about the field investigation showed that eCO2 lead to a higher C/N ratio of litter and soil compared to aCO2, especially for the strong responsive cultivar. eCO2-induced enhanced carbon input stimulated the fungal decomposition pathway by increasing fungal biomass, fungi: bacteria ratio and fungivorous nematode. Results from the manipulative incubation experiment showed eCO2-induced lower quality of straw decreased cumulative C mineralization, but changes in detritus food web induced by eCO2 and strongly responsive cultivar lead to an increased CO2 respiration coincidently within each straw type, mainly due to the adaption to the high C/N ratio environment which increased their functional breadth. Based on SEMs and curves of carbon mineralization rate, soil communities showed significant effects on C release at the early stage through mediating enzyme

  12. Experimental study on the strength parameter of Quarry Dust mixed Coconut Shell Concrete adding Coconut Fibre

    Science.gov (United States)

    Matangulu Shrestha, Victor; Anandh, S.; Sindhu Nachiar, S.

    2017-07-01

    Concrete is a heterogeneous mixture constitute of cement as the main ingredient with a different mix of fine and coarse aggregate. The massive use of conventional concrete has a shortfall in its key ingredients, natural sand and coarse aggregate, due to increased industrialisation and globalisation. To overcome the shortage of material, an alternate material with similar mechanical properties and composition has to be studied, as replacement of conventional concrete. Coconut shell concrete is a prime option as replacement of key ingredients of conventional concrete as coconut is produced in massive quantity in south East Asia. Coconut shell concrete is lightweight concrete and different research is still ongoing concerning about its mix design and composition in the construction industry. Concrete is weak in tension as compared to compression, hence the fibre is used to refrain the crack in the concrete. Coconut fibre is one of many fibres which can be used in concrete. The main aim of this project is to analyse the use of natural by-products in the construction industry, make light weight concrete and eco-friendly construction. This project concerns with the comparison of the mechanical properties of coconut shell concrete and conventional concrete, replacing fine aggregate with quarry dust using coconut fibre. M25 grade of concrete was adopted and testing of concrete was done at the age of 3, 7 and 28 days. In this concrete mix, sand was replaced completely in volumetric measurement by quarry dust. The result was analysed and compared with addition of coconut fibre at varying percentage of 1%, 2%, 3%, 4% and 5%. From the test conducted, coconut shell concrete with quarry dust has the maximum value at 4% of coconut fibre while conventional concrete showed the maximum value at 2% of coconut fibre.

  13. FUNCTIONAL CONVERSION OF GRANITE QUARRIES (methodological aspects of architectural and urban planning solutions

    Directory of Open Access Journals (Sweden)

    PODOLYNNY S. I.

    2016-09-01

    Full Text Available Summary. Raising of problem. There is a global problem of the decline of the economy and production today in Ukraine. Particularly worsened is the situation in the mining industry and the settlements associated with it. There was a threat of mass unemployment in connection with the closure of many enterprises in this field. In this case, the problem of recultivation of technogenic landscapes exist at the same time with possible acute social crisis in these regions. Such areas remain gray spots in the structures of cities and their suburbs, in addition they cause catastrophic damage to the environment. The total area of the changed landscape in Ukraine is almost 800 thousand hectares, important is the question of their further use, based on evidencerecommendations, including architectural and urban development decisions. Purpose. Тo provide a methodical basis for decision-making in conversion of technogenic landscapes, which will enable the search for more adequate methods in the select of the remediationdirection, that is relevant not only to the Dnipropetrovsk region, but also for Ukraine as a whole. Conclusion. The article discusses and classified experience and methods of recultivation of technogenic landscapes of previous years in different countries. It is developed a quarry passport-card, which groups together the existing criteria of the quarry characteristics evaluation, helps to analyze its condition and determine the prospects for further development.

  14. Ecological Input Assessment and EIA: A Study On EIA Report For Quarry Projects

    Directory of Open Access Journals (Sweden)

    Rahimah Wahid

    2016-12-01

    Full Text Available The Environmental Impact Assessment (EIA was introduced as mandatory in Malaysia since 1988 as a measurement tool to achieve sustainable development. This study attempts to assess the EIA reports for quarrying activities which have been submitted to the Department of Environment. There are 19 scheduled activities requiring an EIA prior to project implementation. As the ecological input is an important part of the EIA report, these studies have tried to analyze the ecological quality of input in four EIA reports prepared for quarrying activities in Peninsular Malaysia. The results show that all aspects of the report comply with the review and sampling methods although there are deficiencies which may be remedied. Four EIA reports show weaknesses in the acquisition of the latest available data. For the preparation of the existing environment sections, the consultants do not feel inclined to make sampling on rock habitat, aquatic habitats and flora and fauna. The insulation measures suggested are not only exhaustive but also ineffective. The residual impact on the ecology is briefly mentioned in all the reports. Generally these EIA reports are found to have many shortcomings in the quality of ecological input and can be improved. Thus, a suggestion with a comprehensive approach and the cooperation of all parties is needed to sustain and complement the EIA.

  15. [Fish community structure and its seasonal change in subtidal sandy beach habitat off southern Gouqi Island].

    Science.gov (United States)

    Wang, Zhen-Hua; Wang, Kai; Zhao, Jing; Zhang, Shou-Yu

    2011-05-01

    To understand the characteristics of fish community structure in sandy beach habitats of island reef water areas, and to evaluate the potential capacity of these habitats in local fish stock maintenance, fishes were monthly collected with multi-mesh trammel nets in 2009 from the subtidal sandy beach habitat off southern Gouqi Island, taking the adjacent rocky reef habitat as the control. alpha and beta species diversity indices, index of relative importance (IRI), relative catch rate, and dominance curve for abundance and biomass (ABC curve) were adopted to compare the fish species composition, diversity, and community pattern between the two habitats, and multivariate statistical analyses such as non-metric multidimensional scaling (nMDS) and cluster were conducted to discuss the fish assemblage patterns. A total of 63 fish species belonging to 11 orders, 38 families, and 56 genera were collected, of which, 46 fish species were appeared in the two habitats. Due to the appearance of more warm water species in sandy bottom, the fishes in subtidal sandy beach habitat showed much higher richness, and the abundance catch rate (ACR) from May to July was higher than that in rocky reef habitat. In most rest months, the ACR in subtidal sandy beach habitat also showed the similar trend. However, the species richness and diversity in spring and summer were significantly lower in subtidal sandy beach habitat than in rocky reef habitat, because of the high species dominance and low evenness in the sandy beach habitat. Japanese tonguefish (Paraplagusia japonica) was the indicator species in the sandy beach habitat, and dominated in early spring, later summer, autumn, and winter when the fishing pressure was not strong. In sandy bottom, a unique community structure was formed and kept in dynamic, due to the nursery use of sandy beach by Japanese anchovy (Engraulis japonicus) from May to July, the gathering of gray mullet (Mugil cephalus) in most months for feeding, and the large

  16. Selective sandstone deterioration in the cathedrals of Salamanca, Textural anisotropy as a cause

    Directory of Open Access Journals (Sweden)

    Martín Patino, María Teresa

    1994-09-01

    Full Text Available Textural sandstone anisotropy is related to the selective deterioration of such stone in buildings. The samples studied come from the Cathedrals of Salamanca. Stone fragments, cut in different directions with regard to the base supporting the ashlars in the wall, are studied by means of a binocular magnifying glass and the Scanning Electron Microscopy (SEM. This shows that the sandstone microfabric has a granular and a laminar microtexture, which correspond to different directions in the plane in question as regards the position of the ashlar. Either of these circumstances coincides with the stone surface on the outside of the building and affect its surface deterioration in a different way. The SEM images of deteriorated stone were compared with those of unaffected stone, with both types coming from differently orientated cuts as regards the position of the ashlar. In conclusion, the position given to the block of stone in the building is of importance for the preservation of the stone. The speed of ultrasound transmission measured in samples from commercial quarries confirms the textural sandstone anisotropy to a greater or lesser extent.

    La anisotropía textural de las areniscas se relaciona con la selectividad de su deterioro en los edificios. Las muestras estudiadas pertenecen a las Catedrales de Salamanca. Fragmentos de piedra, cortados en direcciones diferentes respecto a la base sobre la que se asientan los sillares en el muro, son estudiados por medio de la lupa binocular y del microscopio electrónico de barrido (SEM. De éstos se deduce que la microfábrica de las areniscas tiene una microtextura granular y otra laminar, que corresponden a direcciones diferentes del plano respecto al asiento del sillar. Una u otra de estas situaciones coincide con la superficie de la piedra expuesta al exterior en el edificio, y afectan a su deterioro superficial de forma diferente. Las capas externas en las que predomina la arcilla

  17. An analysis of the synoptic and dynamical characteristics of hurricane Sandy (2012)

    Science.gov (United States)

    Varlas, George; Papadopoulos, Anastasios; Katsafados, Petros

    2018-01-01

    Hurricane Sandy affected the Caribbean Islands and the Northeastern United States in October 2012 and caused 233 fatalities, severe rainfalls, floods, electricity blackouts, and 75 billion U.S. dollars in damages. In this study, the synoptic and dynamical characteristics that led to the formation of the hurricane are investigated. The system was driven by the interaction between the polar jet displacement and the subtropical jet stream. In particular, Sandy was initially formed as a tropical depression system over the Caribbean Sea and the unusually warm sea drove its intensification. The interaction between a rapidly approaching trough from the northwest and the stagnant ridge over the Atlantic Ocean drove Sandy to the northeast coast of United States. To better understand the dynamical characteristics and the mechanisms that triggered Sandy, a non-hydrostatic mesoscale model has been used. Model results indicate that the surface heat fluxes and the moisture advection enhanced the convective available potential energy, increased the low-level convective instability, and finally deepened the hurricane. Moreover, the upper air conditions triggered the low-level frontogenesis and increased the asymmetry of the system which finally affected its trajectory.

  18. Telehealth at the US Department of Veterans Affairs after Hurricane Sandy.

    Science.gov (United States)

    Der-Martirosian, Claudia; Griffin, Anne R; Chu, Karen; Dobalian, Aram

    2018-01-01

    Background Like other integrated health systems, the US Department of Veterans Affairs has widely implemented telehealth during the past decade to improve access to care for its patient population. During major crises, the US Department of Veterans Affairs has the potential to transition healthcare delivery from traditional care to telecare. This paper identifies the types of Veterans Affairs telehealth services used during Hurricane Sandy (2012), and examines the patient characteristics of those users. Methods This study conducted both quantitative and qualitative analyses. Veterans Affairs administrative and clinical data files were used to illustrate the use of telehealth services 12 months pre- and 12 months post- Hurricane Sandy. In-person interviews with 31 key informants at the Manhattan Veterans Affairs Medical Center three-months post- Hurricane Sandy were used to identify major themes related to telecare. Results During the seven-month period of hospital closure at the Manhattan Veterans Affairs Medical Center after Hurricane Sandy, in-person patient visits decreased dramatically while telehealth visits increased substantially, suggesting that telecare was used in lieu of in-person care for some vulnerable patients. The most commonly used types of Veterans Affairs telehealth services included primary care, triage, mental health, home health, and ancillary services. Using qualitative analyses, three themes emerged from the interviews regarding the use of Veterans Affairs telecare post- Hurricane Sandy: patient safety, provision of telecare, and patient outreach. Conclusion Telehealth offers the potential to improve post-disaster access to and coordination of care. More information is needed to better understand how telehealth can change the processes and outcomes during disasters. Future studies should also evaluate key elements, such as adequate resources, regulatory and technology issues, workflow integration, provider resistance, diagnostic fidelity and

  19. Lessons from Hurricane Sandy for port resilience.

    Science.gov (United States)

    2013-12-01

    New York Harbor was directly in the path of the most damaging part of Hurricane Sandy causing significant impact on many of the : facilities of the Port of New York and New Jersey. The U.S. Coast Guard closed the entire Port to all traffic before the...

  20. Geological and blocky modeling of Qareh Qeshlaq marble deposit in order to optimizing the production planning of quarry

    Directory of Open Access Journals (Sweden)

    Jafar Abdollahi Sharif

    2013-04-01

    Full Text Available Qareh Qeshlaq marble quarry as one of the valuable resources of ornamental stones in West Azarbaijan province formed through thermal carbonate springs while its mineral deposit thickness is limited in comparison with surface extension. In the present research, geological and blocky modeling of the marble deposit was carried out in order to develop a production planning for this quarry, identifying the position of single-marketable-block extracted from it and increasing its economical aspects for exploitation. During the study, in addition to preparing a geological and blocky model for the quarry, firstly the optimum dimensions of its extractable single marketable-block were quantified and then through representing the confining surfaces equation of marble strata in the computer, the optimal maximum dimension and the number and exact location of the single marketable-blocks were determined and presented to the operating team. Based on the findings of these studies and according to the existing 83 exploratory boreholes data, it is possible to extract 183 single marketable-block pink marble and 103 single marketable-block malachite both with 1.5 × 2.5 × 2.5 m raw dimensions while only 2 single marketable-block alabaster layer with 1.3 × 2.5 × 2.5 m dimensions. The results also show that with applying extraction consideration, regarding the productivity coefficient of the layers, and removing the gradual color changes zone, the maximum thickness of the single marketable-blocks for the pink marble, malachite, and alabaster will become 1.65, 1.65 and 1.4 m, respectively.

  1. Height perception influenced by texture gradient.

    Science.gov (United States)

    Tozawa, Junko

    2012-01-01

    Three experiments were carried out to examine whether a texture gradient influences perception of relative object height. Previous research implicated texture cues in judgments of object width, but similar influences have not been demonstrated for relative height. In this study, I evaluate a hypothesis that the projective ratio of the number of texture elements covered by the objects combined with the ratio of the retinal object heights determines percepts of relative object height. Density of texture background was varied: four density conditions ranged from no-texture to very dense texture. In experiments 1 and 2, participants judged the height of comparison bar compared to the standard bar positioned on no-texture or textured backgrounds. Results showed relative height judgments differed with texture manipulations, consistent with predictions from a hypothesised combination of the number of texture elements with retinal height (experiment 1), or partially consistent with this hypothesis (experiment 2). In experiment 2, variations in the position of a comparison object showed that comparisons located far from the horizon were judged more poorly than in other positions. In experiment 3 I examined distance perception; relative distance judgments were found to be also affected by textured backgrounds. Results are discussed in terms of Gibson's relational theory and distance calibration theory.

  2. Can quarries supplement rare xeric habitats in a piedmont region? Spiders of the Blansky les Mts, Czech Republic

    Czech Academy of Sciences Publication Activity Database

    Tropek, R.; Konvička, Martin

    2008-01-01

    Roč. 19, č. 1 (2008), s. 104-114 ISSN 1085-3278 R&D Projects: GA MŠk LC06073 Institutional research plan: CEZ:AV0Z50070508 Keywords : anthropogenous sites * spiders * quarries Subject RIV: EH - Ecology, Behaviour Impact factor: 1.245, year: 2008

  3. Sandy lower Gotherivian reservoirs in the south central Turkmeniya. [Siberia

    Energy Technology Data Exchange (ETDEWEB)

    Mavyyev, N.Ch.; Nedirov, B.R.

    1982-01-01

    Composition and capacitance-filtering properties of sandy rocks of the early Gotherivian age developed on the fields of Karadzhaulak and Cirili within the northeast slope of the Predkopetdag marginal trough and on areas of Dengli Bakharadok of the Bakharadok monocline are studied. These rocks are viewed as analogs of the gas-bearing Shatlyk level of the Murgabskiy Basin. They can be considered the main potential source of hydrocarbons on the studied territory. In the upper part of the lower Gotherivian, a level of sandy rocks is traced. Rocks represented by small-and average-grained red and light grey differences in sandstones of polymictic composition. The porosity of the sandstones is 20-22%, permeability is 200-500 mdarcy. Not only a similar stratigraphic position of the described sandstones in the lower Gotherivian was found, but also lithological common nature of the rocks. In the south central Turkmeniya one can isolate age analogs of the Shatlyk level, the main productive level of southeast Turkmeniya. The thickness of the sandy beds is from 17 to 45 m. The sandstones of the Karadzhaulak area have the best capacitance-filtering properties. Post sedimentation changes depend on the quantity and composition of the cement, influence of formation waters, and possibly thermobaric conditions of rock formation. The presence of sandy rocks with high collector properties in the cross section of the lower Gotherivian deposits in south central Turkmeniya should be considered in determining the objects for further prospecting and exploration. The areas of Kumbet and Karadzhaulak are primary.

  4. Quantifying the Digital Traces of Hurricane Sandy on Flickr

    Science.gov (United States)

    Preis, Tobias; Moat, Helen Susannah; Bishop, Steven R.; Treleaven, Philip; Stanley, H. Eugene

    2013-11-01

    Society's increasing interactions with technology are creating extensive ``digital traces'' of our collective human behavior. These new data sources are fuelling the rapid development of the new field of computational social science. To investigate user attention to the Hurricane Sandy disaster in 2012, we analyze data from Flickr, a popular website for sharing personal photographs. In this case study, we find that the number of photos taken and subsequently uploaded to Flickr with titles, descriptions or tags related to Hurricane Sandy bears a striking correlation to the atmospheric pressure in the US state New Jersey during this period. Appropriate leverage of such information could be useful to policy makers and others charged with emergency crisis management.

  5. Spatial patterns and natural recruitment of native shrubs in a semi-arid sandy land.

    Science.gov (United States)

    Wu, Bo; Yang, Hongxiao

    2013-01-01

    Passive restoration depending on native shrubs is an attractive approach for restoring desertified landscapes in semi-arid sandy regions. We sought to understand the relationships between spatial patterns of native shrubs and their survival ability in sandy environments. Furthermore, we applied our results to better understand whether passive restoration is feasible for desertified landscapes in semi-arid sandy regions. The study was conducted in the semi-arid Mu Us sandy land of northern China with the native shrub Artemisia ordosica. We analyzed population structures and patterns of A. ordosica at the edges and centers of land patches where sand was stabilized by A. ordosica-dominated vegetation. Saplings were more aggregated than adults, and both were more aggregated at the patch edges than at the patch centers. At the patch edges, spatial association of the saplings with the adults was mostly positive at distances 0.3-6.6 m, and turned from positive to neutral, and even negative, at other distances. At the patch centers, the saplings were spaced almost randomly around the adults, and their distances from the adults did not seem to affect their locations. A greater number of A. ordosica individuals emerged at the patch edges than at the patch centers. Such patterns may have resulted from their integrative adjustment to specific conditions of soil water supply and sand drift intensity. These findings suggest that in semi-arid sandy regions, native shrubs that are well-adapted to local environments may serve as low-cost and competent ecological engineers that can promote the passive restoration of surrounding patches of mobile sandy land.

  6. Proposal of new convenient extractant for assessing phytoavailability of heavy metals in contaminated sandy soil.

    Science.gov (United States)

    Korzeniowska, Jolanta; Stanislawska-Glubiak, Ewa

    2017-06-01

    The aim of the study was to compare the usefulness of 1 M HCl with aqua regia, EDTA, and CaCl 2 for the extraction of phytoavailable forms of Cu, Ni, and Zn on coarse-textured soils contaminated with these metals. Two microplot experiments were used for the studies. Reed canary grass (Phalaris arundinacea), maize (Zea mays), willow (Salix viminalis), spartina (Spartina pectinata), and miscanthus (Miscanthus × giganteus) were used as test plants. They were grown on soil artificially spiked with Cu, Ni, and Zn. The experimental design included a control and three increasing doses of metals. Microplots (1 m 2  × 1 m deep) were filled with sandy soil (clay-6%, pH 5.5, Corg-0.8%). Metals in the form of sulfates were dissolved in water and applied to the plot using a hand liquid sprayer. During the harvest, samples were collected from aboveground parts, roots, and the soil and then tested for their Cu, Zn, and Ni contents. The metal content of the soil was determined using four tested extractants. It was found that Cu and Ni were accumulated in roots in bigger amounts than Zn. The usefulness of the extractants was evaluated based on the correlation between the content of metals in the soil and the plant (n = 32). This study demonstrated that 1 M HCl, aqua regia, and EDTA were more efficient or equally useful for the assessment of the phytoavailability of Cu, Ni, and Zn as CaCl 2 . Due to the ease of performing determinations and their low cost, 1 M HCl can be recommended to assess the excess of Cu, Ni, and Zn in the coarse-textured soils.

  7. Mining and environment: a case study of the Lish-Gish basins of the eastern Himalayas

    International Nuclear Information System (INIS)

    Basu, S.R.; Ghatowar, Likhaneswar

    1990-01-01

    This paper calls for attention to the effects of the unscientific quarrying operations in the coal-fields of the Lish-Gish Basin which have continued intermittently since 1896. The sudden abandonment of the mining operation in 1965, taking least concern of the scars formed due to the extraction of coal have disturbed the natural equilibrium in slopes. This has already taken its toll in the form of disastrous landslips. All these, in turn, incapacitate the rivers pouring in too much detritus which raise the river-beds alarmingly (50 cm. per year) and aggravate the flood situation in times of high rainfall. Immediate steps should therefore, be taken to prevent such unhealthy and destructive processes and specially, in view of the recent attempt by the government of West Bengal, to restart the quarry operations in near future, in order to cope with the longstanding fuel demand of the local inhabitants. (author). 7 refs

  8. Texture memory and strain-texture mapping in a NiTi shape memory alloy

    International Nuclear Information System (INIS)

    Ye, B.; Majumdar, B. S.; Dutta, I.

    2007-01-01

    The authors report on the near-reversible strain hysteresis during thermal cycling of a polycrystalline NiTi shape memory alloy at a constant stress that is below the yield strength of the martensite. In situ neutron diffraction experiments are used to demonstrate that the strain hysteresis occurs due to a texture memory effect, where the martensite develops a texture when it is cooled under load from the austenite phase and is thereafter ''remembered.'' Further, the authors quantitatively relate the texture to the strain by developing a calculated strain-texture map or pole figure for the martensite phase, and indicate its applicability in other martensitic transformations

  9. THE PROBLEMATIC OF SANDY LANDS IN PARANAVAI MUNICIPALITY –PR

    Directory of Open Access Journals (Sweden)

    Marcelo Eduardo Freres Stipp

    2005-05-01

    Full Text Available The sandy lands are a process of scouring with sand forming a sandy area, which correspondsto a reworking of the sands due its constant mobility, involving the transformation of notsolids deposits is sandy areas. This work tried to establish the characterization of thisphenomenon of scouring with sand in a local level, occurring in arenaceous areas in theNortheast of the state of Paraná, specifically in the urban site of Paranavaí. It was also madean evaluation of the environmental degradation as well as different causes for what provokedthese sandy areas. Being an area with a high level of soil decomposition with the highwaysroutes crossing it, it was necessary, besides bibliographic data that allowed a theoretical basis,a research applied in order to supply subsides for future planning related to the spaceorganization. The evolution of the use and soil occupation in this area has been processedwithin an urban planning which considered by no account neither soil characteristic, thevegetation nor the predominant climate in that region. The mechanisms of region atmospherecirculation were analyzed, the alterations or attributes of the climate as well, aiming toidentify the genesis of the erosion sandy and possible time and space distribution. Initially, themain characteristics of the region were collected, components e processes working on the landmodel. It was observed how it worked and the use and occupation of the soil in past times andcurrently. During 2004, using the Environmental Fragility Letter, the areas of erosion wereidentified, ravines and strong erosion that compounds the first stages of the focused problem.The sandy land is a process that involves erosion, transport, e accumulation, meaning most oftimes the loosing of Biosphere productivity. For monitoring these risk areas some measuringcanes were made to measure the soil loss, which were used in several spots of erosion in theurban area in Paranavaí. The measurement happened in

  10. The chert quarrying and processing industry at the Piatra Tomii site, Romania

    Directory of Open Access Journals (Sweden)

    Otis Norman Crandell

    2015-03-01

    Full Text Available Fieldwalking surveys in 2007 and 2008 revealed a moderate sized settlement on Piatra Tomii Hill (Alba County, Romania which was considered of interest because of its location on top of a natural source of chert, and the large amount of chert artefacts found on the surface. In 2009 the site was excavated during which one of the objectives was to learn more about the chert mining and processing at the site. The ratio of artefact types and lack of use-wear suggests that not only was raw material being extracted at the site, but tools were also being produced locally before being exported. The 2009 excavations also revealed what appear to be the remains of pit quarrying and possibly fire cracked limestone and debris. These finds provide technical insight into potential chert extraction techniques utilised in the Late Chalcolithic and Early Bronze Age. As well, this is as yet the only reported settlement in the Transylvanian basin involved in chert extraction (either quarrying or mining. Given the settlement’s affluence, especially considering its relative isolation, it is likely that the chert industry here was important to communities in the vicinity. Indeed artefacts found at contemporary sites in the Mureș Valley appear to have been made from the same or a similar chert. This paper gives an introductions to the site, describes the artefacts and features found there and provides possible interpretations  regarding the processing and export industry, as well as the methods of extracting the raw material during this period.

  11. Migration of cesium-137 through sandy soil layer effect of fine silt on migration

    International Nuclear Information System (INIS)

    Ohnuki, Toshihiko; Wadachi, Yoshiki

    1983-01-01

    The migration of 137 Cs through sandy soil layer was studied with consideration of the migration of fine silt by column method. It was found that a portion of fine silt migrated through the soil layer accompanying with 137 Cs. The mathematical migration model of 137 Cs involved the migration of fine silt through such soil layer was presented. This model gave a good accordance between calculated concentration distribution curve in sandy soil layer and effluent curve and observed those. So, this model seems to be advanced one for evaluating migration of 137 Cs in sandy soil layer with silt. (author)

  12. Analysis of storm-tide impacts from Hurricane Sandy in New York

    Science.gov (United States)

    Schubert, Christopher E.; Busciolano, Ronald J.; Hearn, Paul P.; Rahav, Ami N.; Behrens, Riley; Finkelstein, Jason S.; Monti, Jack; Simonson, Amy E.

    2015-07-21

    The hybrid cyclone-nor’easter known as Hurricane Sandy affected the mid-Atlantic and northeastern United States during October 28-30, 2012, causing extensive coastal flooding. Prior to storm landfall, the U.S. Geological Survey (USGS) deployed a temporary monitoring network from Virginia to Maine to record the storm tide and coastal flooding generated by Hurricane Sandy. This sensor network augmented USGS and National Oceanic and Atmospheric Administration (NOAA) networks of permanent monitoring sites that also documented storm surge. Continuous data from these networks were supplemented by an extensive post-storm high-water-mark (HWM) flagging and surveying campaign. The sensor deployment and HWM campaign were conducted under a directed mission assignment by the Federal Emergency Management Agency (FEMA). The need for hydrologic interpretation of monitoring data to assist in flood-damage analysis and future flood mitigation prompted the current analysis of Hurricane Sandy by the USGS under this FEMA mission assignment.

  13. Textured perovskite cells

    NARCIS (Netherlands)

    Deelen, J. van; Tezsevin, Y.; Barink, M.

    2017-01-01

    Most research of texturization of solar cells has been devoted to Si based cells. For perovskites, it was assumed that texturization would not have much of an impact because of the relatively low refractive indexes lead to relatively low reflection as compared to the Si based cells. However, our

  14. Efficient rolling texture predictions and texture-sensitive thermomechanical properties of α-uranium foils

    Science.gov (United States)

    Steiner, Matthew A.; Klein, Robert W.; Calhoun, Christopher A.; Knezevic, Marko; Garlea, Elena; Agnew, Sean R.

    2017-11-01

    Finite element (FE) analysis was used to simulate the strain history of an α-uranium foil during cold straight-rolling, with the sheet modeled as an isotropic elastoplastic continuum. The resulting strain history was then used as input for a viscoplastic self-consistent (VPSC) polycrystal plasticity model to simulate crystallographic texture evolution. Mid-plane textures predicted via the combined FE→VPSC approach show alignment of the (010) poles along the rolling direction (RD), and the (001) poles along the normal direction (ND) with a symmetric splitting along RD. The surface texture is similar to that of the mid-plane, but with a shear-induced asymmetry that favors one of the RD split features of the (001) pole figure. Both the mid-plane and surface textures predicted by the FE→VPSC approach agree with published experimental results for cold straight-rolled α-uranium plates, as well as predictions made by a more computationally intensive full-field crystal plasticity based finite element model. α-uranium foils produced by cold-rolling must typically undergo a recrystallization anneal to restore ductility prior to their final application, resulting in significant texture evolution from the cold-rolled plate deformation texture. Using the texture measured from a foil in the final recrystallized state, coefficients of thermal expansion and the elastic stiffness tensors were calculated using a thermo-elastic self-consistent model, and the anisotropic yield loci and flow curves along the RD, TD, and ND were predicted using the VPSC code.

  15. The ecology of sandy beaches in Transkei

    African Journals Online (AJOL)

    Data from an ecological survey of three sandy beaches in. Transkei and from Gulu beach on the eastern Cape coast,. South Africa, are presented. Physical parameters such as beach profile, sand particle size, Eh and carbonate content, as well as abundance, composition, biomass and distribution of the macrofauna and ...

  16. Perceptual asymmetry in texture perception.

    OpenAIRE

    Williams, D; Julesz, B

    1992-01-01

    A fundamental property of human visual perception is our ability to distinguish between textures. A concerted effort has been made to account for texture segregation in terms of linear spatial filter models and their nonlinear extensions. However, for certain texture pairs the ease of discrimination changes when the role of figure and ground are reversed. This asymmetry poses a problem for both linear and nonlinear models. We have isolated a property of texture perception that can account for...

  17. REDUCTION OF GROUND MOTION INTENSITY CAUSED BY BLASTING ON STONE QUARRIES"HERCEGOVAC" AND "MAX-STOJA"

    Directory of Open Access Journals (Sweden)

    Marin Petrov

    1993-12-01

    Full Text Available Ground motion intensity caused by deep-hole blasting on the stone quarries »Hercegovac« and »Max-Stoja« was determined by measuring of ground vibrations magnitudes and by interpretation of measuring results under world damage criteria for structures. Reduction of ground motion intensity was realized on the basis of calculation of permissible charge quantity per ignition level (the paper is published in Croatian.

  18. The effect of substrate texture and oxidation temperature on oxide texture development in zirconium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Garner, A., E-mail: alistair.garner@manchester.ac.uk [Materials Performance Centre, University of Manchester, Grosvenor Street, Manchester, M17HS (United Kingdom); Frankel, P. [Materials Performance Centre, University of Manchester, Grosvenor Street, Manchester, M17HS (United Kingdom); Partezana, J. [Westinghouse Electric Company, 1332 Beulah Road, Pittsburgh, PA 15235 (United States); Preuss, M. [Materials Performance Centre, University of Manchester, Grosvenor Street, Manchester, M17HS (United Kingdom)

    2017-02-15

    During corrosion of zirconium alloys a highly textured oxide is formed, the degree of this preferred orientation has previously been shown to be an important factor in determining the corrosion behaviour of these alloys. Two distinct experiments were designed in order to investigate the origin of this oxide texture development on two commercial alloys. Firstly, sheet samples of Zircaloy-4 were oxidised between 500 and 800 °C in air. The resulting monoclinic oxide texture strength was observed to decrease with increasing oxidation temperature. In a second experiment, orthogonal faces of Low Tin ZIRLO{sub ™} were oxidised in 360 °C water, providing different substrate textures but identical microstructures. The substrate texture was observed to have a negligible effect on the corrosion performance whilst the major orientation of both oxide phases was found to be independent of substrate orientation. It is concluded that the main driving force for oxide texture development in single-phase zirconium alloys is the compressive stress caused by the Zr−ZrO{sub 2} transformation. - Highlights: • Substrate orientation does not significantly affect oxide texture development. • Corrosion performance is independent of substrate texture. • Monoclinic oxide texture strength decreases with increasing oxidation temperature. • The main driving force for texture development is the oxidation-induced stress.

  19. Structural stability and hydraulic conductivity of Nkpologu sandy ...

    African Journals Online (AJOL)

    vincent

    mean weight diameter (MWD), water dispersible silt (WDSi), aggregate size distributions (> 2 mm, 1-0.5 mm and < 0.25 ... above sea level. ... and red to brownish red and derived from sandy ... where Q = steady state volume of outflow from the.

  20. Lessons from Hurricane Sandy: a community response in Brooklyn, New York.

    Science.gov (United States)

    Schmeltz, Michael T; González, Sonia K; Fuentes, Liza; Kwan, Amy; Ortega-Williams, Anna; Cowan, Lisa Pilar

    2013-10-01

    The frequency and intensity of extreme weather events have increased in recent decades; one example is Hurricane Sandy. If the frequency and severity continue or increase, adaptation and mitigation efforts are needed to protect vulnerable populations and improve daily life under changed weather conditions. This field report examines the devastation due to Hurricane Sandy experienced in Red Hook, Brooklyn, New York, a neighborhood consisting of geographically isolated low-lying commercial and residential units, with a concentration of low-income housing, and disproportionate rates of poverty and poor health outcomes largely experienced by Black and Latino residents. Multiple sources of data were reviewed, including street canvasses, governmental reports, community flyers, and meeting transcripts, as well as firsthand observations by a local nonprofit Red Hook Initiative (RHI) and community members, and social media accounts of the effects of Sandy and the response to daily needs. These data are considered within existing theory, evidence, and practice on protecting public health during extreme weather events. Firsthand observations show that a community-based organization in Red Hook, RHI, was at the center of the response to disaster relief, despite the lack of staff training in response to events such as Hurricane Sandy. Review of these data underscores that adaptation and response to climate change and likely resultant extreme weather is a dynamic process requiring an official coordinated governmental response along with on-the-ground volunteer community responders.

  1. Jet Fans Airing Quarries in Combination with a Device for Aerating

    Directory of Open Access Journals (Sweden)

    I. I. Starostin

    2015-01-01

    Full Text Available Relevance of study is caused by the search for effective schemes and devices to intensify air exchange of open pits, which is, substantially, worsen with increasing depth of pits and intensity of mining operations. To implement air exchange of pits the scheme of ventilation with simultaneously used device for aeration of pits (DAP is offered. DAP represents the inclined profiled blades on the support, which are set on the top platform of the pit leeside near the edge (patent-protected useful DAP model and based on the turbo-propeller aviation engines pit fan (PF before it. The associated works in the field concerned consider general development factors of free and semi-limited jets, being developed near a flat surface that is different from their development in the conditions of limiting quarry out space with various parameters (overall slope angles, depth, benches at the edges, etc.. The work objective was to study and define the structure and optimal arrangement of PF in respect to DAP and estimate efficiency of using DAP+PF scheme through modelling in a wind tunnel by criterion of average speed of aerial currents in the pit, using a DAP+PF scheme of ventilation.Features of development of aerial currents in pits with various parameters are analysed. Consistent patterns of speed distribution of in semi-limited jet currents are determined. It is proved that the air amount involved in air exchange increases by 8-10 times in comparison with the case with one PF used. The offered air exchange scheme of the quarry out space can be used both for an intensification of airing pit, and for its ventilation. The received study results of aerial current aerodynamics can be used in designing air exchange of pits according to the offered scheme.

  2. Perceptual asymmetry in texture perception.

    Science.gov (United States)

    Williams, D; Julesz, B

    1992-07-15

    A fundamental property of human visual perception is our ability to distinguish between textures. A concerted effort has been made to account for texture segregation in terms of linear spatial filter models and their nonlinear extensions. However, for certain texture pairs the ease of discrimination changes when the role of figure and ground are reversed. This asymmetry poses a problem for both linear and nonlinear models. We have isolated a property of texture perception that can account for this asymmetry in discrimination: subjective closure. This property, which is also responsible for visual illusions, appears to be explainable by early visual processes alone. Our results force a reexamination of the process of human texture segregation and of some recent models that were introduced to explain it.

  3. Aging and Curing Temperature Effects on Compressive Strength of Mortar Containing Lime Stone Quarry Dust and Industrial Granite Sludge

    Directory of Open Access Journals (Sweden)

    Muhammad Nasir Amin

    2017-06-01

    Full Text Available In this study, the researchers investigated the potential use of locally available waste materials from the lime stone quarry and the granite industry as a partial replacement of cement. Quarry sites and granite industry in the eastern province of Saudi Arabia produces tons of powder wastes in the form of quarry dust (QD and granite sludge (GS, respectively, causing serious environmental problems along with frequent dust storms in the area. According to ASTM C109, identical 50-mm3 specimens were cast throughout this study to evaluate the compressive strength development of mortars (7, 28 and 91 days containing these waste materials. Experimental variables included different percentage replacement of cement with waste materials (GS, QD, fineness of GS, various curing temperatures (20, 40 and 60 °C as local normal and hot environmental temperatures and curing moisture (continuously moist and partially moist followed by air curing. Finally, the results of mortar containing waste materials were compared to corresponding results of control mortar (CM and mortar containing fly ash (FA. The test results indicated that under normal curing (20 °C, moist cured, the compressive strength of mortar containing the different percentage of waste materials (QD, GS, FA and their combinations remained lower than that of CM at all ages. However, the compressive strength of mortar containing waste materials slightly increased with increased fineness of GS and significantly increased under high curing temperatures. It was recommended that more fineness of GS be achieved to use its high percentage replacement with cement (30% or more incorporating local environmental conditions.

  4. Characterization of pore system and their influence on decay rates caused by salt weathering on limestones and dolostones quarried in Abanto (Zaragoza, Spain

    Directory of Open Access Journals (Sweden)

    Gisbert, J.

    2010-06-01

    Full Text Available The Abanto natural stone is a rock used in modern constructions and currently quarried as an ornamental rock in Abanto, Zaragoza. The varieties described here are a limestone with depositional texture and a crystalline limestone. In this work we have carried out a detailed study of the mineralogy, texture, hydric behaviour, pore system characteristics, dynamic behaviour and behaviour against the effects of salt crystallisation. After 30 cycles of salts crystallization, the weight loss in these rocks is lower than 0.5%. This low weathering is a consequence of the configuration of their pore system, characterised by a low open porosity and high percentages of microporosity with pore-throat sizes on average of less than a 0.2 µm. The petrographical and physical characteristics, as well as its high resistance against salt crystallisation confer these rocks a high technical quality for their use as building stones in modern construction.

    La piedra natural de Abanto es un material utilizado en obra civil moderna y explotado como roca Ornamental en Abanto (Zaragoza. Las variedades caracterizadas son una caliza con textura deposicional y una caliza cristalina. En este trabajo se ha realizado un detallado estudio de su mineralogía, textura, características del sistema poroso, comportamiento hídrico, comportamiento dinámico y de su comportamiento frente a la cristalización de sales. La pérdida en peso en estas rocas es inferior al 0,5% tras realizar 30 ciclos de cristalización de sales. Esta baja alterabilidad es consecuencia de la configuración del sistema poroso, caracterizado por presentar una baja porosidad abierta y porcentajes elevados de microporosidad con tamaños de radios de acceso de poro preferentemente inferiores a 0,2 µm. Sus características petrográficas y físicas, así como su elevada resistencia frente a la cristalización de sales, les confieren unas buenas cualidades técnicas para su utilización como

  5. Vulnerable, But Why? Post-Traumatic Stress Symptoms in Older Adults Exposed to Hurricane Sandy.

    Science.gov (United States)

    Heid, Allison R; Christman, Zachary; Pruchno, Rachel; Cartwright, Francine P; Wilson-Genderson, Maureen

    2016-06-01

    Drawing on pre-disaster, peri-disaster, and post-disaster data, this study examined factors associated with the development of post-traumatic stress disorder (PTSD) symptoms in older adults exposed to Hurricane Sandy. We used a sample of older participants matched by gender, exposure, and geographic region (N=88, mean age=59.83 years) in which one group reported clinically significant levels of PTSD symptoms and the other did not. We conducted t-tests, chi-square tests, and exact logistic regressions to examine differences in pre-disaster characteristics and peri-disaster experiences. Older adults who experienced PTSD symptoms reported lower levels of income, positive affect, subjective health, and social support and were less likely to be working 4 to 6 years before Hurricane Sandy than were people not experiencing PTSD symptoms. Those developing PTSD symptoms reported more depressive symptoms, negative affect, functional disability, chronic health conditions, and pain before Sandy and greater distress and feelings of danger during Hurricane Sandy. Exact logistic regression revealed independent effects of preexisting chronic health conditions and feelings of distress during Hurricane Sandy in predicting PTSD group status. Our findings indicated that because vulnerable adults can be identified before disaster strikes, the opportunity to mitigate disaster-related PTSD exists through identification and resource programs that target population subgroups. (Disaster Med Public Health Preparedness. 2016;10:362-370).

  6. The impact of Hurricane Sandy on the mental health of New York area residents.

    Science.gov (United States)

    Schwartz, Rebecca M; Sison, Cristina; Kerath, Samantha M; Murphy, Lisa; Breil, Trista; Sikavi, Daniel; Taioli, Emanuela

    2015-01-01

    To evaluate the long-term psychological impact of Hurricane Sandy on New York residents. Prospective, cross-sectional study. Community-based study. From October 2013 to February 2015, 669 adults in Long Island, Queens, and Staten Island completed a survey on their behavioral and psychological health, demographics, and hurricane impact (ie, exposure). Depression, anxiety, and post-traumatic stress disorder (PTSD). Using multivariable logistic regression models, the relationships between Hurricane Sandy exposure and depression, anxiety, and PTSD were examined. Participants experienced an average of 3.9 exposures to Hurricane Sandy, most of which were related to property damage/loss. Probable depression was reported in 33.4 percent of participants, probable anxiety in 46 percent, and probable PTSD in 21.1 percent. Increased exposure to Hurricane Sandy was significantly associated with a greater likelihood of depression (odds ratio [OR] = 1.09, 95% confidence interval [CI]: 1.04-1.14), anxiety (OR = 1.08, 95% CI: 1.03-1.13), and probable PTSD (OR = 1.32, 95% CI: 1.23-1.40), even after controlling for demographic factors known to increase susceptibility to mental health issues. Individuals affected by Hurricane Sandy reported high levels of mental health issues and were at an increased risk of depression, anxiety, and PTSD in the years following the storm. Recovery and prevention efforts should focus on mental health issues in affected populations.

  7. Gravitational effects of global textures

    International Nuclear Information System (INIS)

    Noetzold, D.

    1990-03-01

    A solution for the dynamics of global textures is obtained. Their gravitational field during the collapse and the subsequent evolution is found to be given solely by a space-time dependent ''deficit solid angle.'' The frequency shift of photons traversing this gravitational field is calculated. The space-time dependent texture metric locally contracts the volume of three-space and thereby induces overdensities in homogeneous matter distributions. There are no gravitational forces unless matter has a nonzero angular momentum with respect to the texture origin which would be the case for moving textures

  8. Suitability of soils of the university of Nigeria, Nsukka for the ...

    African Journals Online (AJOL)

    The Nkpologu series of valley bottom, plain and gentle slopes (0-6%) are suitable due to favorable topography, moderately heavy soil textures (sandy clay loam to sandy loam at the topsoil, and sandy clay at the subsoil), and relative soil fertility (with average topsoil % base sat. on the basis of ECEC of 45.08% and O.M. ...

  9. Block Volume Estimation from the Discontinuity Spacing Measurements of Mesozoic Limestone Quarries, Karaburun Peninsula, Turkey

    OpenAIRE

    Elci, Hakan; Turk, Necdet

    2014-01-01

    Block volumes are generally estimated by analyzing the discontinuity spacing measurements obtained either from the scan lines placed over the rock exposures or the borehole cores. Discontinuity spacing measurements made at the Mesozoic limestone quarries in Karaburun Peninsula were used to estimate the average block volumes that could be produced from them using the suggested methods in the literature. The Block Quality Designation (BQD) ratio method proposed by the authors has been found to ...

  10. Stationary and transient thermal states of barometric pumping in the access pit of an underground quarry.

    Science.gov (United States)

    Perrier, Frédéric; Le Mouël, Jean-Louis

    2016-04-15

    The transition zone between free and underground atmospheres hosts spectacular phenomena, as demonstrated by temperature measurements performed in the 4.6m diameter and 20m deep vertical access pit of an abandoned underground quarry located in Vincennes, near Paris. In summer, a stable stratification of the atmosphere is maintained, with coherent temperature variations associated with atmospheric pressure changes, with a barometric tide S2 larger than 0.1°C peak to peak. When the winter regime of turbulent cold air avalanches is initiated, stratification with pressure induced signals can be restored transiently in the upper part of the pit, while the lower part remains fully mixed and insensitive to pressure variations. The amplitude of the pressure to temperature transfer function increases with frequency below 5×10(-4)Hz, with values at 3×10(-5)Hz varying from 0.1°C·hPa(-1) at the bottom up to 2°C·hPa(-1) towards the top of the pit. These temperature variations are accounted for by cave breathing, which is pressure induced motion of air amplified by the large volume of the quarry. This understanding is supported by a numerical model including advective heat transport, heat diffusion, and heat exchange with the pit walls. Mean lifetime in the pit is of the order of 9 to 13h, and barometric pumping results in an effective ventilation rate of the quarry of the order of 10(-7)s(-1). This study illustrates the important role of barometric pumping in heat and matter transport between atmosphere and lithosphere. The resulting stationary and transient states, revealed in this pit, are probably a general feature of functioning interface systems, and therefore are an important aspect to consider in problems of contaminant transport, or the preservation of precious heritage such as rare ecosystems or painted caves. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. The effects of Hurricane Sandy on trauma center admissions.

    Science.gov (United States)

    Curran, T; Bogdanovski, D A; Hicks, A S; Bilaniuk, J W; Adams, J M; Siegel, B K; DiFazio, L T; Durling-Grover, R; Nemeth, Z H

    2018-02-01

    Hurricane Sandy was a particularly unusual storm with regard to both size and location of landfall. The storm landed in New Jersey, which is unusual for a tropical storm of such scale, and created hazardous conditions which caused injury to residents during the storm and in the months following. This study aims to describe differences in trauma center admissions and patterns of injury during this time period when compared to a period with no such storm. Data were collected for this study from patients who were admitted to the trauma center at Morristown Medical Center during Hurricane Sandy or the ensuing cleanup efforts (patients admitted between 29 October 2012 and 27 December 2012) as well as a control group consisting of all patients admitted to the trauma center between 29 October 2013 and 27 December 2013. Patient information was collected to compare the admissions of the trauma center during the period of the storm and cleanup to the control period. A total of 419 cases were identified in the storm and cleanup period. 427 were identified for the control. Striking injuries were more common in the storm and cleanup group by 266.7% (p = 0.0107); cuts were more common by 650.8% (p = 0.0044). Medical records indicate that many of these injuries were caused by Hurricane Sandy. Self-inflicted injuries were more common by 301.3% (p = 0.0294). There were no significant differences in the total number of patients, mortality, or injury severity score between the two cohorts. The data we have collected show that the conditions caused by Hurricane Sandy and the following cleanup had a significant effect on injury patterns, with more patients having been injured by being struck by falling or thrown objects, cut while using tools, or causing self-inflicted injuries. These changes, particularly during the cleanup period, are indicative of environmental changes following the storm which increase these risks of injury.

  12. Transformations in destination texture

    DEFF Research Database (Denmark)

    Gyimóthy, Szilvia

    2018-01-01

    This article takes heterogeographical approaches to understand Bollywood-induced destination transformations in Switzerland. Positioned within the theoretical field of mediatized mobility, the study contextualizes Bollywood-induced tourism in Europe the concept of texture. Textural analysis (base...

  13. Radon emanation coefficients in sandy soils

    International Nuclear Information System (INIS)

    Holy, K.; Polaskova, A.; Baranova, A.; Sykora, I.; Hola, O.

    1998-01-01

    In this contribution the results of the study of an influence of the water content on the emanation coefficient for two sandy soil samples are reported. These samples were chosen on the because of the long-term continual monitoring of the 222 Rn concentration just in such types of soils and this radon concentration showed the significant variations during a year. These variations are chiefly given in connection with the soil moisture. Therefore, the determination of the dependence of the emanation coefficient of radon on the water content can help to evaluate the influence of the soil moisture variations of radon concentrations in the soil air. The presented results show that the emanation coefficient reaches the constant value in the wide interval of the water content for both sandy soil samples. Therefore, in the common range of the soil moisture (5 - 20 %) it is impossible to expect the variations of the radon concentration in the soil air due to the change of the emanation coefficient. The expressive changes of the radon concentration in the soil air can be observed in case of the significant decrease of the emanation coefficient during the soil drying when the water content decreases under 5 % or during the complete filling of the soil pores by the water. (authors)

  14. Annealing texture of rolled nickel alloys

    International Nuclear Information System (INIS)

    Meshchaninov, I.V.; Khayutin, S.G.

    1976-01-01

    A texture of pure nickel and binary alloys after the 95% rolling and annealing has been studied. Insoluble additives (Mg, Zr) slacken the cubic texture in nickel and neral slackening of the texture (Zr). In the case of alloying with silicium (up to 2%) the texture practically coinsides with that of a technical-grade nickel. The remaining soluble additives either do not change the texture of pure nickel (C, Nb) or enhance the sharpness and intensity of the cubic compontnt (Al, Cu, Mn, Cr, Mo, W, Co -at their content 0.5 to 2.0%). A model is proposed by which variation of the annealing texture upon alloying is caused by dissimilar effect of the alloying elements on the mobility of high- and low-angle grain boundaries

  15. Effects of agricultural subsidies of nutrients and detritus on fish and plankton of shallow-reservoir ecosystems.

    Science.gov (United States)

    Pilati, Alberto; Vanni, Michael J; González, María J; Gaulke, Alicia K

    2009-06-01

    Agricultural activities increase exports of nutrients and sediments to lakes, with multiple potential impacts on recipient ecosystems. Nutrient inputs enhance phytoplankton and upper trophic levels, and sediment inputs can shade phytoplankton, interfere with feeding of consumers, and degrade benthic habitats. Allochthonous sediments are also a potential food source for detritivores, as is sedimenting autochthonous phytodetritus, the production of which is stimulated by nutrient inputs. We examined effects of allochthonous nutrient and sediment subsidies on fish and plankton, with special emphasis on gizzard shad (Dorosoma cepedianum). This widespread and abundant omnivorous fish has many impacts on reservoir ecosystems, including negative effects on water quality via nutrient cycling and on fisheries via competition with sportfish. Gizzard shad are most abundant in agriculturally impacted, eutrophic systems; thus, agricultural subsidies may affect reservoir food webs directly and by enhancing gizzard shad biomass. We simulated agricultural subsidies of nutrients and sediment detritus by manipulating dissolved nutrients and allochthonous detritus in a 2 x 2 factorial design in experimental ponds. Addition of nutrients alone increased primary production and biomass of zooplanktivorous fish (bluegill and young-of-year gizzard shad). Addition of allochthonous sediments alone increased algal sedimentation and decreased seston and sediment C:P ratios. Ponds receiving both nutrients and sediments showed highest levels of phytoplankton and total phosphorus. Adult and juvenile gizzard shad biomass was enhanced equally by nutrient or sediment addition, probably because this apparently P-limited detritivore ingested similar amounts of P in all subsidy treatments. Nutrient excretion rates of gizzard shad were higher in ponds with nutrient additions, where sediments were composed mainly of phytodetritus. Therefore, gizzard shad can magnify the direct effects of nutrient

  16. Fine natural aggregate replacement for sandy residue from itabirite exploitation in Portland cement mortar

    International Nuclear Information System (INIS)

    Melo, V.A.R.; Freire, C.B.; Pereira Junior, S.S.; Lameiras, F.S.; Tello, C.C.O.

    2011-01-01

    The fine natural aggregates are a material largely used by the civil construction for mortar and concrete production. Due to tightening legal restrictions imposed on their extraction, alternative materials are being considered. The use of sandy residue from BIF (banded iron formations) exploitation was investigated. It requires their grinding and flotation to concentrate iron oxides. Large amounts of sandy residue composed of quartz and iron oxides are generated in this process. The sandy residue was characterized relative to mineralogical composition, particle size distribution, presence of organic impurities, and particle shape. Mortar formulations were prepared by varying the type of cement, the cement to aggregate proportion and the water/cement ratio (a/c). The results of viscosity and density of fresh mortar, setting time, and compressive strength are presented. Compressive strength up to 19.5 MPa at 28 days were achieved with the use of cement CPV, a/c ratio of 0.80 and cement:aggregate proportion of 1:2. The results demonstrate the technical feasibility of using sandy residue as fine aggregate. (author)

  17. Laser surface texturing of tool steel: textured surfaces quality evaluation

    Science.gov (United States)

    Šugár, Peter; Šugárová, Jana; Frnčík, Martin

    2016-05-01

    In this experimental investigation the laser surface texturing of tool steel of type 90MnCrV8 has been conducted. The 5-axis highly dynamic laser precision machining centre Lasertec 80 Shape equipped with the nano-second pulsed ytterbium fibre laser and CNC system Siemens 840 D was used. The planar and spherical surfaces first prepared by turning have been textured. The regular array of spherical and ellipsoidal dimples with a different dimensions and different surface density has been created. Laser surface texturing has been realized under different combinations of process parameters: pulse frequency, pulse energy and laser beam scanning speed. The morphological characterization of ablated surfaces has been performed using scanning electron microscopy (SEM) technique. The results show limited possibility of ns pulse fibre laser application to generate different surface structures for tribological modification of metallic materials. These structures were obtained by varying the processing conditions between surface ablation, to surface remelting. In all cases the areas of molten material and re-cast layers were observed on the bottom and walls of the dimples. Beside the influence of laser beam parameters on the machined surface quality during laser machining of regular hemispherical and elipsoidal dimple texture on parabolic and hemispherical surfaces has been studied.

  18. Hurricane Sandy: Rapid Response Imagery of the Surrounding Regions

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The imagery posted on this site is of Hurricane Sandy. The aerial photography missions were conducted by the NOAA Remote Sensing Division. The images were acquired...

  19. 2014 USGS CMGP Lidar: Sandy Restoration (Delaware and Maryland)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Geographic Extent: SANDY_Restoration_DE_MD_QL2 Area of Interest covers approximately 3.096 square miles. Lot #5 contains the full project area Dataset Description:...

  20. Fine-scale spatial distribution of plants and resources on a sandy soil in the Sahel

    NARCIS (Netherlands)

    Rietkerk, M.G.; Ouedraogo, T.; Kumar, L.; Sanou, S.; Langevelde, F. van; Kiema, A.; Koppel, J. van de; Andel, J. van; Hearne, J.; Skidmore, A.K.; Ridder, N. de; Stroosnijder, L.; Prins, H.H.T.

    2002-01-01

    We studied fine-scale spatial plant distribution in relation to the spatial distribution of erodible soil particles, organic matter, nutrients and soil water on a sandy to sandy loam soil in the Sahel. We hypothesized that the distribution of annual plants would be highly spatially autocorrelated

  1. Feeding preference and daily ration of 12 dominant copepods on mono and mixed diets of phytoplankton, rotifers, and detritus in a tropical coastal water.

    Science.gov (United States)

    Jagadeesan, L; Jyothibabu, R; Arunpandi, N; Anjusha, A; Parthasarathi, S; Pandiyarajan, R S

    2017-09-11

    Results of the experimental studies on the feeding habit and daily ration (DR) of 12 dominant copepods from a tropical coastal water (off Kochi, Southwest coast of India) on different food items (phytoplankton, rotifers, and detritus) are presented. Even though, all species of copepods consumed all types of food items in the experiments, they showed noticeable feeding preferences, having important ecological implications. Calanoid Paracalanus parvus and Acrocalanus gracilis consumed phytoplankton and rotifers equally in mono diets (74-89% of DR) and mixed diets (53-82% of DR), which indicated their ability to shift their diet in natural environment based on the availability of food items. Calanoid Acartia erythraea and A. danae consumed more phytoplankton (DR 83 and 72%, respectively) than rotifers (DR 51 and 46%, respectively) in mono diets, and in mixed diets, their consumption was high in phytoplankton combined food mixtures (P + R DR and P + D DR) rather than the R + D food type, indicated their preference for mixed diets of phytoplankton. Similarly, Calanoid Temora turbinata, Pseudodiaptomus serricaudatus, and Centropages tenuiremis preferred a herbivorous diet as evidenced by their high ingestion rate on phytoplankton mono (70 to 87% to their DR) and mixed diets (58 to 80% of DR). On the other hand, Cyclopoid Oithona similis and Poecilostomatoid Corycaeus danae preferred a carnivorous diet, consuming more rotifers (> 80% of DR) than phytoplankton (18-20% of DR) and detritus (5-6% of DR). Harpacticoids Macrosetella gracilis and Euterpina acutifrons equally preferred phytoplankton (78-92% of DR) and detritus (65-89% of DR). The study showed that the dominant copepods in the coastal waters off Kochi occupy different trophic niches available in the environment, which may be applicable in other similar environments as well.

  2. 3D MODELLING AND ACCURACY ASSESSMENT OF GRANITE QUARRY USING UNMMANNED AERIAL VEHICLE

    Directory of Open Access Journals (Sweden)

    D. González-Aguilera

    2012-07-01

    Full Text Available The unmanned aerial vehicles (UAVs are automated systems whose main characteristic is that can be remotely piloted. This property is especially interesting in those civil engineering works in which the accuracy of the model is not reachable by common aerial or satellite systems, there is a difficult accessibility to the infrastructure due to location and geometry aspects, and the economic resources are limited. This paper aims to show the research, development and application of a UAV that will generate georeferenced spatial information at low cost, high quality, and high availability. In particular, a 3D modelling and accuracy assessment of granite quarry using UAV is applied. With regard to the image-based modelling pipeline, an automatic approach supported by open source tools is performed. The process encloses the well-known image-based modelling steps: calibration, extraction and matching of features; relative and absolute orientation of images and point cloud and surface generation. Beside this, an assessment of the final model accuracy is carried out by means of terrestrial laser scanner (TLS, imaging total station (ITS and global navigation satellite system (GNSS in order to ensure its validity. This step follows a twofold approach: (i firstly, using singular check points to provide a dimensional control of the model and (ii secondly, analyzing the level of agreement between the realitybased 3D model obtained from UAV and the generated with TLS. The main goal is to establish and validate an image-based modelling workflow using UAV technology which can be applied in the surveying and monitoring of different quarries.

  3. Health risk assessment linked to filling coastal quarries with treated dredged seaport sediments

    International Nuclear Information System (INIS)

    Perrodin, Yves; Donguy, Gilles; Emmanuel, Evens; Winiarski, Thierry

    2014-01-01

    Dredged seaport sediments raise complex management problems since it is no longer possible to discharge them into the sea. Traditional waste treatments are poorly adapted for these materials in terms of absorbable volumes and cost. In this context, filling quarries with treated sediments appears interesting but its safety regarding human health must be demonstrated. To achieve this, a specific methodology for assessing health risks has been developed and tested on three seaport sediments. This methodology includes the development of a conceptual model of the global scenario studied and the definition of specific protocols for each of its major steps. The approach proposed includes in particular the use of metrological and experimental tools that are new in this context: (i) an experimental lysimeter for characterizing the deposit emissions, and (ii) a geological radar for identifying potential preferential pathways between the sediment deposit and the groundwater. The application of this approach on the three sediments tested for the scenario studied showed the absence of health risk associated with the consumption of groundwater for substances having a “threshold effect” (risk quotient −6 ). - Highlights: • The release of polluted dredged seaport sediments into the sea must be avoided. • Their use after treatment for the filling-up of quarries is proposed by managers. • An original health risk assessment methodology was created to validate this option. • It includes the use of a lysimeter and a georadar for the exposure assessment stage. • The example studied concludes to a health risk linked to arsenic in the groundwater

  4. A Coordinated USGS Science Response to Hurricane Sandy

    Science.gov (United States)

    Jones, S.; Buxton, H. T.; Andersen, M.; Dean, T.; Focazio, M. J.; Haines, J.; Hainly, R. A.

    2013-12-01

    In late October 2012, Hurricane Sandy came ashore during a spring high tide on the New Jersey coastline, delivering hurricane-force winds, storm tides exceeding 19 feet, driving rain, and plummeting temperatures. Hurricane Sandy resulted in 72 direct fatalities in the mid-Atlantic and northeastern United States, and widespread and substantial physical, environmental, ecological, social, and economic impacts estimated at near $50 billion. Before the landfall of Hurricane Sandy, the USGS provided forecasts of potential coastal change; collected oblique aerial photography of pre-storm coastal morphology; deployed storm-surge sensors, rapid-deployment streamgages, wave sensors, and barometric pressure sensors; conducted Light Detection and Ranging (lidar) aerial topographic surveys of coastal areas; and issued a landslide alert for landslide prone areas. During the storm, Tidal Telemetry Networks provided real-time water-level information along the coast. Long-term networks and rapid-deployment real-time streamgages and water-quality monitors tracked river levels and changes in water quality. Immediately after the storm, the USGS serviced real-time instrumentation, retrieved data from over 140 storm-surge sensors, and collected other essential environmental data, including more than 830 high-water marks mapping the extent and elevation of the storm surge. Post-storm lidar surveys documented storm impacts to coastal barriers informing response and recovery and providing a new baseline to assess vulnerability of the reconfigured coast. The USGS Hazard Data Distribution System served storm-related information from many agencies on the Internet on a daily basis. Immediately following Hurricane Sandy the USGS developed a science plan, 'Meeting the Science Needs of the Nation in the Wake of Hurricane Sandy-A U.S. Geological Survey Science Plan for Support of Restoration and Recovery'. The plan will ensure continuing coordination of internal USGS activities as well as

  5. Structural Stability and Hydraulic Conductivity Of Nkpologu Sandy ...

    African Journals Online (AJOL)

    Studies were conducted in the runoff plots at the University of Nigeria Nsukka Teaching and Resesarch Farm in 2010 and 2011 to monitor the changes in structural stability and saturated hydraulic conductivity (Ksat) of Nkpologu sandy loam soil under different cover management practices. The management practices were ...

  6. Relation of historical quarrying, material utilization and performance on buildings in Eastern Finland

    Science.gov (United States)

    Luodes, Nike M.; Pirinen, Heikki

    2016-04-01

    Finland might seem to have lower stone heritage compared to other southern European countries, but it has been the main exporter of dimension stone to the majestic buildings that made St.Petersburg a recognized cultural heritage. In Finland, though, the stone seems undervalued. The only dramatic and predominant stone buildings are those of agencies and administrations located in the towns, where the stone has been used to impress and symbolize value. Romantic style used massive bossy stone in building's full height and created fine traditional carvings. Otherwise the communities have mainly built settlements in contact with the nature, with materials easily available and of low cost, following architectonical trends of the periods and producing interesting stone details. During the past years, research has been conducted on historical buildings interconnecting scientific and artistic approach to evaluate material durability and cultural relevance of the artifacts. Generally until mid 20th century the stone has been traditionally used massive for basements and walls. The materials still present good mechanical characteristics and most often the weathering level after hundreds of years of exposure had reached only the first millimeters from the curst. Instead the old methodology for deposit exploitation has left visible signs on the buildings. Some examples are visible from Kuopio. The exploitation of small, easy-to-reach surface deposits, even if planned by local experts, has affected quality and appearance of historical buildings. As an example the excavation of shallow quarries where also weathered crop was kept as a product has characterized the basement of the Niirala school that presents change in colors due to original material more than to weathering on site. Fissuring is also visible on a couple of blocks while marks on the rocks depict the old excavation method. Most often the deposits had been in the vicinities, frequently hidden by further construction

  7. Conophyton occur in Burgueno Quarry (Nueva Carrara, Uruguay): outcrop new of Grupo Mina Verdun and its importance

    International Nuclear Information System (INIS)

    Gaucher, C.; Cernuschi, F.; Chiglino, L.

    2004-01-01

    The succession exposed in the Burgueno Quarry, in the vicinity of Nueva Carrara (Maldonado, Uruguay), is here assigned to the Mina Verdun Group. It is composed, from base to top, by meta marls, calcareous breccias and limestones, stromatolitic limestones and massive dolostones. Exposed thickness exceeds 110 m. Stromatolites assigned to the group Conophyton occur in the stromatolitic limestones (El Calabozo Formation). Stromatolites are characterized by straight to sinuous columns, showing circular to elliptical transverse sections 1.5 to 26 cm in maximum diameter. Height of columns exceeds 50 cm. The stromatolitic laminations are well preserved. Sedimentary environment for this unit is inferred as sub tidal, under low energy conditions. The Las Ventanas Formation overlies with angular and erosional unconformity the Mina Verdun Group at Burgueno Quarry. The Las Palmas Formation is tentatively correlated with the Las Ventanas Formation, on the basis of stratigraphic relationships and lithologic similarity. Considering the data presented here, it is envisaged that the Lavalleja/Fuente del Puma Group is not part of the basement of the Las Ventanas Formation. A Proterozoic, pre-Vendian age is postulated for the Mina Verdun Group, thus older than ca. 600 Ma [es

  8. 2014 USGS CMGP Lidar: Post Sandy (Long Island, NY)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — TASK NAME: Long Island New York Sandy LIDAR lidar Data Acquisition and Processing Production Task USGS Contract No. G10PC00057 Task Order No. G14PD00296 Woolpert...

  9. Hurricane Sandy science plan: coastal impact assessments

    Science.gov (United States)

    Stronko, Jakob M.

    2013-01-01

    Hurricane Sandy devastated some of the most heavily populated eastern coastal areas of the Nation. With a storm surge peaking at more than 19 feet, the powerful landscape-altering destruction of Hurricane Sandy is a stark reminder of why the Nation must become more resilient to coastal hazards. In response to this natural disaster, the U.S. Geological Survey (USGS) received a total of $41.2 million in supplemental appropriations from the Department of the Interior (DOI) to support response, recovery, and rebuilding efforts. These funds support a science plan that will provide critical scientific information necessary to inform management decisions for recovery of coastal communities, and aid in preparation for future natural hazards. This science plan is designed to coordinate continuing USGS activities with stakeholders and other agencies to improve data collection and analysis that will guide recovery and restoration efforts. The science plan is split into five distinct themes: coastal topography and bathymetry, impacts to coastal beaches and barriers, impacts of storm surge, including disturbed estuarine and bay hydrology, impacts on environmental quality and persisting contaminant exposures, impacts to coastal ecosystems, habitats, and fish and wildlife. This fact sheet focuses assessing impacts to coastal beaches and barriers.

  10. Rapid Assessment of Anthropogenic Impacts of Exposed Sandy ...

    African Journals Online (AJOL)

    We applied a rapid assessment methodology to estimate the degree of human impact of exposed sandy beaches in Ghana using ghost crabs as ecological indicators. The use of size ranges of ghost crab burrows and their population density as ecological indicators to assess extent of anthropogenic impacts on beaches ...

  11. Texture classification using autoregressive filtering

    Science.gov (United States)

    Lawton, W. M.; Lee, M.

    1984-01-01

    A general theory of image texture models is proposed and its applicability to the problem of scene segmentation using texture classification is discussed. An algorithm, based on half-plane autoregressive filtering, which optimally utilizes second order statistics to discriminate between texture classes represented by arbitrary wide sense stationary random fields is described. Empirical results of applying this algorithm to natural and sysnthesized scenes are presented and future research is outlined.

  12. CRUMB TEXTURE OF SPELT BREAD

    Directory of Open Access Journals (Sweden)

    Joanna Korczyk-Szabó

    2013-12-01

    Full Text Available Abstract The bread quality is considerably dependent on the texture characteristic of bread crumb. Crumb texture is an important quality indicator, as consumer prefer different bread taste. Texture analysis is primarily concerned with the evaluation of mechanical characteristics where a material is subjected to a controlled force from which a deformation curve of its response is generated. It is an objective physical examination of baked products and gives direct information on the product quality, oppositely to dough rheology tests what inform on the baking suitability of the flour, as raw material. This is why the texture analysis is one of the most helpful analytical methods of the product development. In the framework of our research during the years 2008 – 2009 were analyzed selected indicators for bread texture quality of five Triticum spelta L. varieties – Altgold, Oberkulmer Rotkorn, Ostro, Rubiota and Franckenkorn grown in an ecological system. The bread texture quality was evaluated on texture analyzer TA.XT Plus (Stable Micro Systems, Surrey, UK, following the AACC (74-09 standard method and expressed as crumb firmness (N, stiffness (N.mm-1 and relative elasticity (%. Our research proved that all selected indicators were significantly influenced by the year of growing and variety. The most soft bread was achieved in Rubiota, whereas bread crumb samples from Franckenkorn and Altgold were the most firm and stiff. Correlation analysis showed strong negative correlation between relative elasticity and bread crumb firmness as well as bread stiffness (-0.81++, -0.78++. The spelt grain can be a good source for making bread flour, but is closely dependent on choice of spelt variety. The spelt wheat bread crumb texture need further investigation as it can be a reliable quality parameter.

  13. KC-46A Formal Training Unit (FTU) and First Main Operating Base (MOB 1) Beddown EIS. Volume 1

    Science.gov (United States)

    2014-03-01

    discharged into the sanitary sewer system. Most of the sanitary sewer system at Altus AFB is over 45 years old and constructed of vitrified clay ...drained (USDA 2002a, 2003). The textures of the Tillman-Hollister soils range from clay loam to clay , with the Hollister subsurface soils being more clayey...range from sandy to sandy loam to sandy clay loam, with the Nobscot soils having a more sandy nature, especially in the surface soils (Altus AFB 2009a

  14. Treatability of volatile chlorinated hydrocarbon-contaminated soils of different textures along a vertical profile by mechanical soil aeration: A laboratory test.

    Science.gov (United States)

    Ma, Yan; Shi, Yi; Hou, Deyi; Zhang, Xi; Chen, Jiaqi; Wang, Zhifen; Xu, Zhu; Li, Fasheng; Du, Xiaoming

    2017-04-01

    Mechanical soil aeration is a simple, effective, and low-cost soil remediation technology that is suitable for sites contaminated with volatile chlorinated hydrocarbons (VCHs). Conventionally, this technique is used to treat the mixed soil of a site without considering the diversity and treatability of different soils within the site. A laboratory test was conducted to evaluate the effectiveness of mechanical soil aeration for remediating soils of different textures (silty, clayey, and sandy soils) along a vertical profile at an abandoned chloro-alkali chemical site in China. The collected soils were artificially contaminated with chloroform (TCM) and trichloroethylene (TCE). Mechanical soil aeration was effective for remediating VCHs (removal efficiency >98%). The volatilization process was described by an exponential kinetic function. In the early stage of treatment (0-7hr), rapid contaminant volatilization followed a pseudo-first order kinetic model. VCH concentrations decreased to low levels and showed a tailing phenomenon with very slow contaminant release after 8hr. Compared with silty and sandy soils, clayey soil has high organic-matter content, a large specific surface area, a high clay fraction, and a complex pore structure. These characteristics substantially influenced the removal process, making it less efficient, more time consuming, and consequently more expensive. Our findings provide a potential basis for optimizing soil remediation strategy in a cost-effective manner. Copyright © 2016. Published by Elsevier B.V.

  15. Symmetry realization of texture zeros

    International Nuclear Information System (INIS)

    Grimus, W.; Joshipura, A.S.; Lavoura, L.; Tanimoto, M.

    2004-01-01

    We show that it is possible to enforce texture zeros in arbitrary entries of the fermion mass matrices by means of Abelian symmetries; in this way, many popular mass-matrix textures find a symmetry justification. We propose two alternative methods which allow one to place zeros in any number of elements of the mass matrices that one wants. They are applicable simultaneously in the quark and lepton sectors. They are also applicable in grand unified theories. The number of scalar fields required by our methods may be large; still, in many interesting cases this number can be reduced considerably. The larger the desired number of texture zeros is, the simpler are the models which reproduce the texture. (orig.)

  16. Texture and anisotropy in ferroelectric lead metaniobate

    Science.gov (United States)

    Iverson, Benjamin John

    Ferroelectric lead metaniobate, PbNb2O6, is a piezoelectric ceramic typically used because of its elevated Curie temperature and anisotropic properties. However, the piezoelectric constant, d33, is relatively low in randomly oriented ceramics when compared to other ferroelectrics. Crystallographic texturing is often employed to increase the piezoelectric constant because the spontaneous polarization axes of grains are better aligned. In this research, crystallographic textures induced through tape casting are distinguished from textures induced through electrical poling. Texture is described using multiple quantitative approaches utilizing X-ray and neutron time-of-flight diffraction. Tape casting lead metaniobate with an inclusion of acicular template particles induces an orthotropic texture distribution. Templated grain growth from seed particles oriented during casting results in anisotropic grain structures. The degree of preferred orientation is directly linked to the shear behavior of the tape cast slurry. Increases in template concentration, slurry viscosity, and casting velocity lead to larger textures by inducing more particle orientation in the tape casting plane. The maximum 010 texture distributions were two and a half multiples of a random distribution. Ferroelectric texture was induced by electrical poling. Electric poling increases the volume of material oriented with the spontaneous polarization direction in the material. Samples with an initial paraelectric texture exhibit a greater change in the domain volume fraction during electrical poling than randomly oriented ceramics. In tape cast samples, the resulting piezoelectric response is proportional to the 010 texture present prior to poling. This results in property anisotropy dependent on initial texture. Piezoelectric properties measured on the most textured ceramics were similar to those obtained with a commercial standard.

  17. Ecotoxicological risk assessment linked to infilling quarries with treated dredged seaport sediments.

    Science.gov (United States)

    Perrodin, Yves; Donguy, Gilles; Bazin, Christine; Volatier, Laurence; Durrieu, Claude; Bony, Sylvie; Devaux, Alain; Abdelghafour, Mohammed; Moretto, Robert

    2012-08-01

    The dredged sediments of polluted seaports now raise complex management problems since it is no longer possible to discharge them into the sea. This results in the need to manage them on land, raising other types of technical, economic and environmental problems. Regarding the technical and economic dimensions, traditional waste treatment methods have proved to be poorly adapted, due to very high costs and low absorbable volumes. In this context, filling quarries in coastal areas with treated sediments could represent an interesting alternative for these materials. Nevertheless, for the environmental dimension, it is necessary to demonstrate that this possibility is harmless to inland ecosystems. Consequently, a specific ecotoxicological risk assessment methodology has been formulated and tested on three sediments taken from seaboards of France, in view to providing an operational and usable tool for the prior validation of any operation to fill quarries with treated seaport sediments. This method incorporates the formulation of a global conceptual model of the scenario studied and the definition of protocols for each of its steps: the characterisation of exposures (based on a simulation of sediment deposit), the characterisation of effects (via the study of sediments ecotoxicity), and the final ecotoxicological risk assessment performed as a calculation of a risk quotient. It includes the implementation in parallel of two types of complementary approach: the "substances" approach derived from the European methodology for assessing new substances placed on the market, and the "matrix" approach which is similar to methods developed in France to assess ecological risks in other domains (waste management, polluted site management, …). The application of this dual approach to the three sediments tested led to conclude with reliability that the project to deposit sediments "1" and "2" presented a low risk for the peripheral aquatic ecosystems while sediment "3

  18. Food Texture Preferences in Infants Versus Toddlers.

    Science.gov (United States)

    Lundy, Brenda; And Others

    1998-01-01

    Compared food texture preferences during infancy and toddlerhood. Found that infants displayed more negative expressions and head and body movements in response to complex textures than to simple textures. Toddlers displayed more positive head and body movements and more eagerness in response to complex than to simple textures. Experience with…

  19. A Combined Remote Sensing-Numerical Modelling Approach to the Stability Analysis of Delabole Slate Quarry, Cornwall, UK

    Science.gov (United States)

    Havaej, Mohsen; Coggan, John; Stead, Doug; Elmo, Davide

    2016-04-01

    Rock slope geometry and discontinuity properties are among the most important factors in realistic rock slope analysis yet they are often oversimplified in numerical simulations. This is primarily due to the difficulties in obtaining accurate structural and geometrical data as well as the stochastic representation of discontinuities. Recent improvements in both digital data acquisition and incorporation of discrete fracture network data into numerical modelling software have provided better tools to capture rock mass characteristics, slope geometries and digital terrain models allowing more effective modelling of rock slopes. Advantages of using improved data acquisition technology include safer and faster data collection, greater areal coverage, and accurate data geo-referencing far exceed limitations due to orientation bias and occlusion. A key benefit of a detailed point cloud dataset is the ability to measure and evaluate discontinuity characteristics such as orientation, spacing/intensity and persistence. This data can be used to develop a discrete fracture network which can be imported into the numerical simulations to study the influence of the stochastic nature of the discontinuities on the failure mechanism. We demonstrate the application of digital terrestrial photogrammetry in discontinuity characterization and distinct element simulations within a slate quarry. An accurately geo-referenced photogrammetry model is used to derive the slope geometry and to characterize geological structures. We first show how a discontinuity dataset, obtained from a photogrammetry model can be used to characterize discontinuities and to develop discrete fracture networks. A deterministic three-dimensional distinct element model is then used to investigate the effect of some key input parameters (friction angle, spacing and persistence) on the stability of the quarry slope model. Finally, adopting a stochastic approach, discrete fracture networks are used as input for 3D

  20. Structural and textural characteristics of slate and its response to the point load test

    Directory of Open Access Journals (Sweden)

    Ana Mladenovič

    2006-12-01

    Full Text Available From the geomechanical point of view slate is considered to be one of more trying rock varieties. The results of research have shown close relationship between structural, textural and mineralogical characteristics on the one hand, and its strength and resistance to point loads on the other hand. Its weakened zones are the result of anisotropy. They develop mainly due to dynamo-metamorphosis of the primary mudstone, resulting in the formation of the secondary slaty cleavage, with a pronounced preferred orientation of the hyllosilicates. Low strength is the consequence of the weak Van der Waals chemical bond between individual packets of the internal crystal structure of the sheet minerals, particularly sericite. Bedding and microfolds with a crenulated structure and partial preferred orientation of sheet minerals, as well as directions that are weakened with sigmoidal shear deformations as the predecessors of microfaults, also result in significant but less problematicanisotropy. Thin lepidoblastic lamina, in apparently massive sandy metasiltstone beds in the slate represent discontinuities, which have a decisive influence on the reduction of their strength.

  1. Texture analysis using Renyi's generalized entropies

    NARCIS (Netherlands)

    Grigorescu, SE; Petkov, N

    2003-01-01

    We propose a texture analysis method based on Renyi's generalized entropies. The method aims at identifying texels in regular textures by searching for the smallest window through which the minimum number of different visual patterns is observed when moving the window over a given texture. The

  2. Use of a Combination of Vertical and Horizontal Boreholes in Massive Blasting of Benches in the Surface Quarry Rodež

    Science.gov (United States)

    Tori, Matija; Vajović, Stanojle; Goleš, Niko; Muhić, Elvir; Peternel, Miha

    2017-12-01

    This article deals with the extraction of minerals (limestone/marl/flysch) in the quarry Rodež, which is located in western Slovenia. During the extraction of minerals in a quarry, drilling and blasting of benches are used. The focus of the article is on the analysis of the parameters related to drilling and blasting in surface excavations when using a combination of explosions and introducing horizontal wells along with vertical holes in the bench. On the basis of the analysis of basic parameters through a combination of drilling horizontal wells and charging those with the ammonal + Anfex explosive, analyses of effects of seismic disturbances on potentially affected buildings have also been conducted. The article is connected to and deals exclusively with the basic parameters of drilling and blasting, with the introduction of horizontal drilling and with the analysis of seismic measurements of threatened buildings in accordance with the German standard German Institute for Standardisation (DIN) 4150 during the use of a new method of blasting.

  3. TEXTURAL DESCRIPTORS FOR MULTIPHASIC ORE PARTICLES

    Directory of Open Access Journals (Sweden)

    Laura Pérez-Barnuevo

    2012-11-01

    Full Text Available Monitoring of mineral processing circuits by means of particle liberation analysis through quantitative image analysis has become a routine technique within the last decades. Usually, liberation indices are computed as weight proportions, which is not informative enough when complex texture ores are treated by flotation. In these cases, liberation has to be computed as phase surface exposed to reactants, and textural relationships between minerals have to be characterized to determine the possibility of increasing exposure. In this paper, some indices to achieve a complete texture characterization have been developed in terms of 2D phase contact and mineral surfaces exposure. Indices suggested by other authors are also compared. The response of this set of parameters against textural changes has been explored on simple synthetic textures ranging from single to multiple inclusions and single to multiple veins and their ability to discriminate between different textural features is analyzed over real mineral particles with known internal structure.

  4. Studies on Thiobacilli spp. isolated from sandy beaches of Kerala

    Digital Repository Service at National Institute of Oceanography (India)

    Gore, P.S.; Raveendran, O.; Unnithan, R.V.

    Occurrence, isolation and oxidative activity of Thiobacilli spp. from some sandy beaches of Kerala are reported. These organisms were encountered in polluted beaches and were dominant during monsoon in all the beaches...

  5. Mimicking human texture classification

    NARCIS (Netherlands)

    Rogowitz, B.E.; van Rikxoort, Eva M.; van den Broek, Egon; Pappas, T.N.; Schouten, Theo E.; Daly, S.J.

    2005-01-01

    In an attempt to mimic human (colorful) texture classification by a clustering algorithm three lines of research have been encountered, in which as test set 180 texture images (both their color and gray-scale equivalent) were drawn from the OuTex and VisTex databases. First, a k-means algorithm was

  6. Storm Impact and Depression Among Older Adults Living in Hurricane Sandy-Affected Areas.

    Science.gov (United States)

    Sirey, Jo Anne; Berman, Jacquelin; Halkett, Ashley; Giunta, Nancy; Kerrigan, Janice; Raeifar, Elmira; Artis, Amanda; Banerjee, Samprit; Raue, Patrick J

    2017-02-01

    Research on the impact of natural disasters on the mental health of older adults finds both vulnerabilities and resilience. We report on the rates of clinically significant depression among older adults (aged ≥60 years) living in areas affected by Hurricane Sandy in 2012 and the factors associated with mental health need. The Sandy Mobilization, Assessment, Referral and Treatment for Mental Health (SMART-MH) program integrates community outreach and needs assessments to identify older adults with mental health and aging service needs. Older adults with significant anxiety or depressive symptoms were offered short-term psychotherapy. Social service referrals were made directly to community agencies. All SMART-MH activities were offered in Spanish, Russian, Mandarin/Cantonese, and English. Across the full sample, 14% of participants screened positive for depression. Hurricane Sandy stressors predicted increased odds of depression, including storm injury, post-storm crime, and the total count of stressors. Outcomes varied significantly by age group, such that all Sandy-related variables remained significant for younger-old adults (aged 60-74 years), whereas only the loss of access to medical care was significant for older-old adults (aged ≥75 years). Storm-affected communities show higher rates of depressive symptoms than seen in the general population, with storm stressors affecting mental health needs differentially by age group. (Disaster Med Public Health Preparedness. 2017;11:97-109).

  7. Development and Application of Syndromic Surveillance for Severe Weather Events Following Hurricane Sandy.

    Science.gov (United States)

    Tsai, Stella; Hamby, Teresa; Chu, Alvin; Gleason, Jessie A; Goodrow, Gabrielle M; Gu, Hui; Lifshitz, Edward; Fagliano, Jerald A

    2016-06-01

    Following Hurricane Superstorm Sandy, the New Jersey Department of Health (NJDOH) developed indicators to enhance syndromic surveillance for extreme weather events in EpiCenter, an online system that collects and analyzes real-time chief complaint emergency department (ED) data and classifies each visit by indicator or syndrome. These severe weather indicators were finalized by using 2 steps: (1) key word inclusion by review of chief complaints from cases where diagnostic codes met selection criteria and (2) key word exclusion by evaluating cases with key words of interest that lacked selected diagnostic codes. Graphs compared 1-month, 3-month, and 1-year periods of 8 Hurricane Sandy-related severe weather event indicators against the same period in the following year. Spikes in overall ED visits were observed immediately after the hurricane for carbon monoxide (CO) poisoning, the 3 disrupted outpatient medical care indicators, asthma, and methadone-related substance use. Zip code level scan statistics indicated clusters of CO poisoning and increased medicine refill needs during the 2 weeks after Hurricane Sandy. CO poisoning clusters were identified in areas with power outages of 4 days or longer. This endeavor gave the NJDOH a clearer picture of the effects of Hurricane Sandy and yielded valuable state preparation information to monitor the effects of future severe weather events. (Disaster Med Public Health Preparedness. 2016;10:463-471).

  8. Borehole radar survey at the granite quarry mine, Pocheon, Kyounggi province

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jung Ho; Cho, Seong Jun; Yi, Myeong Jong; Chung, Seung Hwan; Lee, Hee Il; Shin, In Chul [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1997-12-01

    Borehole radar survey in combination with the reflection and tomography methods was conducted at the Donga granite quarry mine of Pocheon area in Kyounggi province. The purpose of radar survey in quarry mine is to delineate the inhomogeneities including fractures and to estimate the freshness of rock. 20 MHz was adopted as the central frequency for the radar reflection and tomography surveys for the longer distance of penetration. The reflection survey using the direction finding antenna was also conducted to get the information on the spatial orientation of reflectors. Besides the various kinds of radar borehole survey, two surface geophysical methods, dipole-dipole resistivity survey and ground penetrating radar, were also applied to delineate the hidden parts of geological structures which was confirmed by geological mapping. The reflection data processing package, RADPRO ver. 2.2, developed continuously through in this study, was used to process the borehole reflection radar data. The new programs to process radar reflection data using directional antenna were devised and used to calculate and image the orientation of reflectors. The major dip angle of fractured zones were determined from the radar reflection images. With the aid of direction finding antenna and the newly developed algorithm to image the orientation of reflectors, it was possible to get the three dimensional attitudes of reflectors. Detailed interpretation results of the surveyed area are included in this report. Through the interpretation of borehole reflection data using dipole and direction finding antenna, we could determine the orientation of the major fractured zone, the boundary of two mining areas. Many of hidden inhomogeneities were found by borehole radar methods. By the image of direction finding antenna, it was confirmed that nearly all of them were located at the outside of the planned mining area or were situated very deeply. Therefore, the surveyed area consists of very fresh and

  9. Description of textures by a structural analysis.

    Science.gov (United States)

    Tomita, F; Shirai, Y; Tsuji, S

    1982-02-01

    A structural analysis system for describing natural textures is introduced. The analyzer automatically extracts the texture elements in an input image, measures their properties, classifies them into some distinctive classes (one ``ground'' class and some ``figure'' classes), and computes the distributions of the gray level, the shape, and the placement of the texture elements in each class. These descriptions are used for classification of texture images. An analysis-by-synthesis method for evaluating texture analyzers is also presented. We propose a synthesizer which generates a texture image based on the descriptions. By comparing the reconstructed image with the original one, we can see what information is preserved and what is lost in the descriptions.

  10. Brazilian sandy beaches: characteristics, ecosystem services, impacts, knowledge and priorities

    Directory of Open Access Journals (Sweden)

    Antonia Cecília Zacagnini Amaral

    Full Text Available ABSTRACT Sandy beaches constitute a key ecosystem and provide socioeconomic goods and services, thereby playing an important role in the maintenance of human populations and in biodiversity conservation. Despite the ecological and social importance of these ecosytems, Brazilian sandy beaches are significantly impacted by human interference, chemical and organic pollution and tourism, as well as global climate change. These factors drive the need to better understand the environmental change and its consequences for biota. To promote the implementation of integrated studies to detect the effects of regional and global environmental change on beaches and on other benthic habitats of the Brazilian coast, Brazilian marine researchers have established The Coastal Benthic Habitats Monitoring Network (ReBentos. In order to provide input for sample planning by ReBentos, we have conducted an intensive review of the studies conducted on Brazilian beaches and summarized the current knowledge about this environment. In this paper, we present the results of this review and describe the physical, biological and socioeconomics features of Brazilian beaches. We have used these results, our personal experience and worldwide literature to identify research projects that should be prioritized in the assessment of regional and global change on Brazilian sandy beaches. We trust that this paper will provide insights for future studies and represent a significant step towards the conservation of Brazilian beaches and their biodiversity.

  11. 77 FR 74891 - Order Granting Exemptions From Certain Rules of Regulation SHO Related to Hurricane Sandy

    Science.gov (United States)

    2012-12-18

    ... Client Update on Superstorm Sandy--Current and Ongoing Operations as Markets Re-Open; Physical.../downloads/legal/imp_notices/2012/dtcc/z0033.pdf ; ``DTCC Client Update on Superstorm Sandy--Physical...://www.dtcc.com/downloads/legal/imp_notices/2012/dtcc/z0035.pdf ; ``DTCC Client Update on Superstorm...

  12. Bacterial polyextremotolerant bioemulsifiers from arid soils improve water retention capacity and humidity uptake in sandy soil

    KAUST Repository

    Raddadi, Noura

    2018-05-31

    Water stress is a critical issue for plant growth in arid sandy soils. Here, we aimed to select bacteria producing polyextremotolerant surface-active compounds capable of improving water retention and humidity uptake in sandy soils.From Tunisian desert and saline systems, we selected eleven isolates able to highly emulsify different organic solvents. The bioemulsifying activities were stable with 30% NaCl, at 4 and 120 °C and in a pH range 4-12. Applications to a sandy soil of the partially purified surface-active compounds improved soil water retention up to 314.3% compared to untreated soil. Similarly, after 36 h of incubation, the humidity uptake rate of treated sandy soil was up to 607.7% higher than untreated controls.Overall, results revealed that polyextremotolerant bioemulsifiers of bacteria from arid and desert soils represent potential sources to develop new natural soil-wetting agents for improving water retention in arid soils.

  13. Bacterial polyextremotolerant bioemulsifiers from arid soils improve water retention capacity and humidity uptake in sandy soil

    KAUST Repository

    Raddadi, Noura; Giacomucci, Lucia; Marasco, Ramona; Daffonchio, Daniele; Cherif, Ameur; Fava, Fabio

    2018-01-01

    Water stress is a critical issue for plant growth in arid sandy soils. Here, we aimed to select bacteria producing polyextremotolerant surface-active compounds capable of improving water retention and humidity uptake in sandy soils.From Tunisian desert and saline systems, we selected eleven isolates able to highly emulsify different organic solvents. The bioemulsifying activities were stable with 30% NaCl, at 4 and 120 °C and in a pH range 4-12. Applications to a sandy soil of the partially purified surface-active compounds improved soil water retention up to 314.3% compared to untreated soil. Similarly, after 36 h of incubation, the humidity uptake rate of treated sandy soil was up to 607.7% higher than untreated controls.Overall, results revealed that polyextremotolerant bioemulsifiers of bacteria from arid and desert soils represent potential sources to develop new natural soil-wetting agents for improving water retention in arid soils.

  14. Bacterial polyextremotolerant bioemulsifiers from arid soils improve water retention capacity and humidity uptake in sandy soil.

    Science.gov (United States)

    Raddadi, Noura; Giacomucci, Lucia; Marasco, Ramona; Daffonchio, Daniele; Cherif, Ameur; Fava, Fabio

    2018-05-31

    Water stress is a critical issue for plant growth in arid sandy soils. Here, we aimed to select bacteria producing polyextremotolerant surface-active compounds capable of improving water retention and humidity uptake in sandy soils. From Tunisian desert and saline systems, we selected eleven isolates able to highly emulsify different organic solvents. The bioemulsifying activities were stable with 30% NaCl, at 4 and 120 °C and in a pH range 4-12. Applications to a sandy soil of the partially purified surface-active compounds improved soil water retention up to 314.3% compared to untreated soil. Similarly, after 36 h of incubation, the humidity uptake rate of treated sandy soil was up to 607.7% higher than untreated controls. Overall, results revealed that polyextremotolerant bioemulsifiers of bacteria from arid and desert soils represent potential sources to develop new natural soil-wetting agents for improving water retention in arid soils.

  15. Sediment Chemistry and Toxicity in Barnegat Bay, New Jersey: Pre- and Post- Hurricane Sandy, 2012-2013.

    Science.gov (United States)

    Romanok, Kristin M.; Szabo, Zoltan; Reilly, Timothy J.; Defne, Zafer; Ganju, Neil K.

    2016-01-01

    Hurricane Sandy made landfall in Barnegat Bay, October, 29, 2012, damaging shorelines and infrastructure. Estuarine sediment chemistry and toxicity were investigated before and after to evaluate potential environmental health impacts and to establish post-event baseline sediment-quality conditions. Trace element concentrations increased throughout Barnegat Bay up to two orders of magnitude, especially north of Barnegat Inlet, consistent with northward redistribution of silt. Loss of organic compounds, clay, and organic carbon is consistent with sediment winnowing and transport through the inlets and sediment transport modeling results. The number of sites exceeding sediment quality guidance levels for trace elements tripled post-Sandy. Sediment toxicity post-Sandy was mostly unaffected relative to pre-Sandy conditions, but at the site with the greatest relative increase for trace elements, survival rate of the test amphipod decreased (indicating degradation). This study would not have been possible without comprehensive baseline data enabling the evaluation of storm-derived changes in sediment quality.

  16. Macrofauna and meiofauna of two sandy beaches at Mombasa, Kenya

    Digital Repository Service at National Institute of Oceanography (India)

    Ansari, Z.A.; Ingole, B.S.; Parulekar, A.H.

    Macrofauna and meiofauna of 2 sandy beaches having medium and fine sand particles, respectively, were investigated, quantitatively Macrofauna density was highest around high water mark and progressively decreased towards low water mark Meiofauna...

  17. Aggregations of the sandy-beach isopod, Tylos granulatus ...

    African Journals Online (AJOL)

    ... lives as a scavenger in the intertidal zone of sandy beaches on the west coast of South Africa. Individuals emerge with the receding tide leaving exit holes, then forage for about two hours before returning to the vicinity of the high-water mark where they aggregate to bury themselves, leaving behind cone-shaped mounds.

  18. Geometric Total Variation for Texture Deformation

    DEFF Research Database (Denmark)

    Bespalov, Dmitriy; Dahl, Anders Lindbjerg; Shokoufandeh, Ali

    2010-01-01

    In this work we propose a novel variational method that we intend to use for estimating non-rigid texture deformation. The method is able to capture variation in grayscale images with respect to the geometry of its features. Our experimental evaluations demonstrate that accounting for geometry...... of features in texture images leads to significant improvements in localization of these features, when textures undergo geometrical transformations. Accurate localization of features in the presense of unkown deformations is a crucial property for texture characterization methods, and we intend to expoit...

  19. Long-Term Observations of Dust Storms in Sandy Desert Environments

    Science.gov (United States)

    Yun, Hye-Won; Kim, Jung-Rack; Choi, Yun-Soo

    2015-04-01

    Mineral dust occupies the largest portion of atmospheric aerosol. Considering the numerous risks that dust poses for socioeconomic and anthropogenic activities, it is crucial to understand sandy desert environments, which frequently generate dust storms and act as a primary source of atmospheric aerosol. To identify mineral aerosol mechanisms, it is essential to monitor desert environmental factors involving dust storm generation in the long term. In this study, we focused on two major environmental factors: local surface roughness and soil moisture. Since installments of ground observation networks in sandy deserts are unfeasible, remote sensing techniques for mining desert environmental factors were employed. The test area was established within the Badain Jaran and Kubuqi Deserts in Inner Mongolia, China, where significant seasonal aeolian processes emit mineral dust that influences all of East Asia. To trace local surface roughness, we employed a multi-angle imaging spectroradiometer (MISR) image sequence to extract multi-angle viewing (MAV) topographic parameters such as normalized difference angular index, which represents characteristics of the target desert topography. The backscattering coefficient from various space-borne SAR and stereotopography were compared with MAV observations to determine calibrated local surface roughness. Soil moisture extraction techniques from InSAR-phase coherence stacks were developed and compiled with advanced scatterometer (ASCAT) soil moisture data. Combined with metrological information such as the European Centre for Medium-Range Weather Forecasts (ECMWF) ERA interim, correlations between intensity of sand dune activity as a proxy of aeolian processes in desert environments, surface wind conditions, and surface soil moisture were traced. Overall, we have confirmed that tracking sandy desert aeolian environments for long-term observations is feasible with space-borne, multi-sensor observations when combined with

  20. Vulnerability of tropical forest ecosystems and forest dependent communities to droughts.

    Science.gov (United States)

    Vogt, D J; Vogt, K A; Gmur, S J; Scullion, J J; Suntana, A S; Daryanto, S; Sigurðardóttir, R

    2016-01-01

    Energy captured by and flowing through a forest ecosystem can be indexed by its total Net Primary Productivity (NPP). This forest NPP can also be a reflection of its sensitivity to, and its ability to adapt to, any climate change while also being harvested by humans. However detecting and identifying the vulnerability of forest and human ecosystems to climate change requires information on whether these coupled social and ecological systems are able to maintain functionality while responding to environmental variability. To better understand what parameters might be representative of environmental variability, we compiled a metadata analysis of 96 tropical forest sites. We found that three soil textural classes (i.e., sand, sandy loam and clay) had significant but different relationships between NPP and precipitation levels. Therefore, assessing the vulnerability of forests and forest dependent communities to drought was carried out using data from those sites that had one of those three soil textural classes. For example, forests growing on soil textures of sand and clay had NPP levels decreasing as precipitation levels increased, in contrast to those forest sites that had sandy loam soils where NPP levels increased. Also, forests growing on sandy loam soil textures appeared better adapted to grow at lower precipitation levels compared to the sand and clay textured soils. In fact in our tropical database the lowest precipitation level found for the sandy loam soils was 821 mm yr(-1) compared to sand at 1739 mm yr(-1) and clay at 1771 mm yr(-1). Soil texture also determined the level of NPP reached by a forest, i.e., forest growing on sandy loam and clay reached low-medium NPP levels while higher NPP levels (i.e., medium, high) were found on sand-textured soils. Intermediate precipitation levels (>1800-3000 mm yr(-1)) were needed to grow forests at the medium and high NPP levels. Low thresholds of NPP were identified at both low (∼750 mm) and high precipitation

  1. ACHIEVEMENTS AND PERSPECTIVES ON STONE FRUIT GROWING ON SANDY SOILS

    Directory of Open Access Journals (Sweden)

    Anica Durău

    2012-01-01

    Full Text Available Climatic conditions in the sandy soils of southern Oltenia encourage cultivation of tree species in terms of applying specific technologies. Possibility of poor sandy soils fertile capitalization, earliness in 7- 10 days of fruit ripening , high yields and quality are the main factors supporting the development of fruit growing in the sandy soils of southern Oltenia. The main objectives of the research were to CCDCPN Dăbuleni. Establish and improve stone fruit species assortment, adapted to the stress of the sandy soils, establishment and evaluation of the influence of stress on trees and their influence on the size and quality of production, development of technological links (planting distances, forms management, fertilization, getting high and consistent annual production of high quality, containing low as pesticide residues, to establish a integrated health control program of the trees with emphasis on biotechnical. Research has shown good stone species behavior, and their recommended proportion is 75% of all fruit trees (peach 36%, 14% apricot, plum15%, sweet and sour cherry fruit growing 10% of the total area. Results on peach varieties revealed: ’Redhaven’, ’Suncrest’, ’Loring’ with yields ranging from (24.8 t / ha to 29.0 t/ha with maturation period from July to August, and varieties ’NJ 244’, ’Fayette’, ’Flacara’ with productions ranging from (19.7 t / ha to 23.0 t/ha with maturation period from August to September. The sweet cherry varieties ’Van’, ’Rainier’, ’Stella’, with yields ranging from 17. 2 to 24.4 t / ha. In the range studied sour cherry were found ’Oblacinska’ varieties of 11.0 t / ha, ’Cernokaia’ with 10.5 t / ha, ’Schatten Morelle’ with 9.1 t / ha. Optimum planting density and shape of the peach crown found that the highest yields of fruit are produced in the form of vertical cordon crown, with values ranging from 15.9 t / ha at a distance of 2 m, 10.3 t / ha at a distance

  2. The technical processes of quarrying in the Late Iron Age of Western Iberia

    Directory of Open Access Journals (Sweden)

    Jesús RODRÍGUEZ HERNÁNDEZ

    2013-01-01

    Full Text Available This paper reconstructs the technical processes involved in producing the stone works made by the communities of Western Iberia during the Late Iron Age. For this study, we use both archaeological and ethnographic data. We analyze the characteristics of granite, the extraction process in the quarry, the available means of transport, the tools used and the carving process, focusing analysis on the zoomorphic sculptures known as “verracos”. Assessment of these technical aspects is essential for the analysis of the finished products and constitutes a first step in better understanding the status of stonemasons within the protohistoric societies of the Western Iberian Peninsula.

  3. Feature-aware natural texture synthesis

    KAUST Repository

    Wu, Fuzhang; Dong, Weiming; Kong, Yan; Mei, Xing; Yan, Dongming; Zhang, Xiaopeng; Paul, Jean Claude

    2014-01-01

    This article presents a framework for natural texture synthesis and processing. This framework is motivated by the observation that given examples captured in natural scene, texture synthesis addresses a critical problem, namely, that synthesis

  4. Deformation texture and microtexture development in zircaloy-2

    International Nuclear Information System (INIS)

    Vanitha, C.; Kiran Kumar, M.; Samajdar, I.; Vishvanathan, N.N.; Dey, G.K.; Tewari, R.; Srivastava, D.; Banerjee, S.

    2002-01-01

    In the present study, two starting materials used were as-cast Zircaloy-2 with random texture and the finished tube with relatively stronger starting texture. Specimens of the alloys were hot rolled to various strains at different temperature. The texture measurement was carried out and was represented in the form of Orientation Distribution Function which showed a sluggish texture development on high temperature deformation. In the case of as cast alloy with increase in strain at a constant deformation temperature, development in the texture was significant. Upon increasing the working temperature, rate of the overall texture development has been found to reduce. This could be due to reduced slip-twin activities, recovery or due to recrystallization. Microstructural and relative hardening studies were carried out for understanding the mechanisms of deformation texture developments at warm and hot working stages. In the case of finished tube having initially strong texture exhibited slower development in texture on warm and hot rolling. (author)

  5. Use of dolomite phosphate rock (DPR) fertilizers to reduce phosphorus leaching from sandy soil

    International Nuclear Information System (INIS)

    Chen, G.C.; He, Z.L.; Stoffella, P.J.; Yang, X.E.; Yu, S.; Calvert, D.

    2006-01-01

    There is increasing concern over P leaching from sandy soils applied with water-soluble P fertilizers. Laboratory column leaching experiments were conducted to evaluate P leaching from a typical acidic sandy soil in Florida amended with DPR fertilizers developed from dolomite phosphate rock (DPR) and N-Viro soil. Ten leaching events were carried out at an interval of 7 days, with a total leaching volume of 1183 mm equivalent to the mean annual rainfall of this region during the period of 2001-2003. Leachates were collected and analyzed for total P and inorganic P. Phosphorus in the leachate was dominantly reactive, accounting for 67.7-99.9% of total P leached. Phosphorus leaching loss mainly occurred in the first three leaching events, accounting for 62.0-98.8% of the total P leached over the whole period. The percentage of P leached (in the total P added) from the soil amended with water-soluble P fertilizer was higher than those receiving the DPR fertilizers. The former was up to 96.6%, whereas the latter ranged from 0.3% to 3.8%. These results indicate that the use of N-Viro-based DPR fertilizers can reduce P leaching from sandy soils. - Fertilizers developed from dolomite phosphate rock (DPR) reduce phosphorus leaching from sandy soil

  6. Texture Repairing by Unified Low Rank Optimization

    Institute of Scientific and Technical Information of China (English)

    Xiao Liang; Xiang Ren; Zhengdong Zhang; Yi Ma

    2016-01-01

    In this paper, we show how to harness both low-rank and sparse structures in regular or near-regular textures for image completion. Our method is based on a unified formulation for both random and contiguous corruption. In addition to the low rank property of texture, the algorithm also uses the sparse assumption of the natural image: because the natural image is piecewise smooth, it is sparse in certain transformed domain (such as Fourier or wavelet transform). We combine low-rank and sparsity properties of the texture image together in the proposed algorithm. Our algorithm based on convex optimization can automatically and correctly repair the global structure of a corrupted texture, even without precise information about the regions to be completed. This algorithm integrates texture rectification and repairing into one optimization problem. Through extensive simulations, we show our method can complete and repair textures corrupted by errors with both random and contiguous supports better than existing low-rank matrix recovery methods. Our method demonstrates significant advantage over local patch based texture synthesis techniques in dealing with large corruption, non-uniform texture, and large perspective deformation.

  7. Cascaded Amplitude Modulations in Sound Texture Perception

    DEFF Research Database (Denmark)

    McWalter, Richard Ian; Dau, Torsten

    2017-01-01

    . In this study, we investigated the perception of sound textures that contain rhythmic structure, specifically second-order amplitude modulations that arise from the interaction of different modulation rates, previously described as "beating" in the envelope-frequency domain. We developed an auditory texture...... model that utilizes a cascade of modulation filterbanks that capture the structure of simple rhythmic patterns. The model was examined in a series of psychophysical listening experiments using synthetic sound textures-stimuli generated using time-averaged statistics measured from real-world textures....... In a texture identification task, our results indicated that second-order amplitude modulation sensitivity enhanced recognition. Next, we examined the contribution of the second-order modulation analysis in a preference task, where the proposed auditory texture model was preferred over a range of model...

  8. Advecting Procedural Textures for 2D Flow Animation

    Science.gov (United States)

    Kao, David; Pang, Alex; Moran, Pat (Technical Monitor)

    2001-01-01

    This paper proposes the use of specially generated 3D procedural textures for visualizing steady state 2D flow fields. We use the flow field to advect and animate the texture over time. However, using standard texture advection techniques and arbitrary textures will introduce some undesirable effects such as: (a) expanding texture from a critical source point, (b) streaking pattern from the boundary of the flowfield, (c) crowding of advected textures near an attracting spiral or sink, and (d) absent or lack of textures in some regions of the flow. This paper proposes a number of strategies to solve these problems. We demonstrate how the technique works using both synthetic data and computational fluid dynamics data.

  9. Superstorm Sandy and the academic achievement of university students.

    Science.gov (United States)

    Doyle, Matthew D; Lockwood, Brian; Comiskey, John G

    2017-10-01

    Much of the literature on the consequences of natural disasters has focused on their physical and psychological ramifications. Few researchers have considered how the impacts of a natural disaster can influence academic achievement. This study analyses data collected from nearly 300 students at a mid-sized, private university in the northeast United States to determine if the effects of Cyclone Sandy in 2012 are associated with measures of academic achievement. The findings reveal that experiencing headaches after the event resulted in a higher likelihood of students suffering a loss of academic motivation. In addition, experiencing headaches and a loss of academic motivation were correlated with a lower grade point average (GPA) during the semester in which Sandy made landfall. However, the more direct effects of the superstorm, including displacement and a loss of power, did not have a significant bearing on academic achievement. Lastly, the paper examines the implications for higher education policy and future research. © 2017 The Author(s). Disasters © Overseas Development Institute, 2017.

  10. Plasticity and density-moisture-resistance relations of soils amended with fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Mapfuno, E.; Chanasyk, D.S. [University of Alberta, Edmonton, AB (Canada). Dept. of Renewable Resources

    1998-06-01

    The objective of this study was to investigate the impact of fly ash amendments on the plasticity, water retention and penetration resistance-density-moisture relationships of three soils of sandy loam, loam and clay loam textures in order to determine the potential compaction of these soil/fly ash mixtures if they were worked at different moisture ranges. For all three soils the addition of fly ash decreased the plasticity index, but slightly increased the Proctor maximum density. This implies that fly ash amendments reduce the range of moisture within which soils are most susceptible to compaction. However, for the sandy loam and loam textured soils amended with fly ash, cultivation must be avoided at moisture contents close to field capacity since maximum densification occurs at these moisture contents. In all three soils the addition of fly ash increased water retention, especially in the sandy loam. Fly ash amendments increased penetration resistance of the clay loam, but increased penetration resistance of the sandy loam.

  11. Cascaded Amplitude Modulations in Sound Texture Perception

    Directory of Open Access Journals (Sweden)

    Richard McWalter

    2017-09-01

    Full Text Available Sound textures, such as crackling fire or chirping crickets, represent a broad class of sounds defined by their homogeneous temporal structure. It has been suggested that the perception of texture is mediated by time-averaged summary statistics measured from early auditory representations. In this study, we investigated the perception of sound textures that contain rhythmic structure, specifically second-order amplitude modulations that arise from the interaction of different modulation rates, previously described as “beating” in the envelope-frequency domain. We developed an auditory texture model that utilizes a cascade of modulation filterbanks that capture the structure of simple rhythmic patterns. The model was examined in a series of psychophysical listening experiments using synthetic sound textures—stimuli generated using time-averaged statistics measured from real-world textures. In a texture identification task, our results indicated that second-order amplitude modulation sensitivity enhanced recognition. Next, we examined the contribution of the second-order modulation analysis in a preference task, where the proposed auditory texture model was preferred over a range of model deviants that lacked second-order modulation rate sensitivity. Lastly, the discriminability of textures that included second-order amplitude modulations appeared to be perceived using a time-averaging process. Overall, our results demonstrate that the inclusion of second-order modulation analysis generates improvements in the perceived quality of synthetic textures compared to the first-order modulation analysis considered in previous approaches.

  12. Natural texture retrieval based on perceptual similarity measurement

    Science.gov (United States)

    Gao, Ying; Dong, Junyu; Lou, Jianwen; Qi, Lin; Liu, Jun

    2018-04-01

    A typical texture retrieval system performs feature comparison and might not be able to make human-like judgments of image similarity. Meanwhile, it is commonly known that perceptual texture similarity is difficult to be described by traditional image features. In this paper, we propose a new texture retrieval scheme based on texture perceptual similarity. The key of the proposed scheme is that prediction of perceptual similarity is performed by learning a non-linear mapping from image features space to perceptual texture space by using Random Forest. We test the method on natural texture dataset and apply it on a new wallpapers dataset. Experimental results demonstrate that the proposed texture retrieval scheme with perceptual similarity improves the retrieval performance over traditional image features.

  13. Epitaxial hexagonal materials on IBAD-textured substrates

    Science.gov (United States)

    Matias, Vladimir; Yung, Christopher

    2017-08-15

    A multilayer structure including a hexagonal epitaxial layer, such as GaN or other group III-nitride (III-N) semiconductors, a oriented textured layer, and a non-single crystal substrate, and methods for making the same. The textured layer has a crystalline alignment preferably formed by the ion-beam assisted deposition (IBAD) texturing process and can be biaxially aligned. The in-plane crystalline texture of the textured layer is sufficiently low to allow growth of high quality hexagonal material, but can still be significantly greater than the required in-plane crystalline texture of the hexagonal material. The IBAD process enables low-cost, large-area, flexible metal foil substrates to be used as potential alternatives to single-crystal sapphire and silicon for manufacture of electronic devices, enabling scaled-up roll-to-roll, sheet-to-sheet, or similar fabrication processes to be used. The user is able to choose a substrate for its mechanical and thermal properties, such as how well its coefficient of thermal expansion matches that of the hexagonal epitaxial layer, while choosing a textured layer that more closely lattice matches that layer.

  14. Longitudinal Impact of Hurricane Sandy Exposure on Mental Health Symptoms

    Directory of Open Access Journals (Sweden)

    Rebecca M. Schwartz

    2017-08-01

    Full Text Available Hurricane Sandy hit the eastern coast of the United States in October 2012, causing billions of dollars in damage and acute physical and mental health problems. The long-term mental health consequences of the storm and their predictors have not been studied. New York City and Long Island residents completed questionnaires regarding their initial Hurricane Sandy exposure and mental health symptoms at baseline and 1 year later (N = 130. There were statistically significant decreases in anxiety scores (mean difference = −0.33, p < 0.01 and post-traumatic stress disorder (PTSD scores (mean difference = −1.98, p = 0.001 between baseline and follow-up. Experiencing a combination of personal and property damage was positively associated with long-term PTSD symptoms (ORadj 1.2, 95% CI [1.1–1.4] but not with anxiety or depression. Having anxiety, depression, or PTSD at baseline was a significant predictor of persistent anxiety (ORadj 2.8 95% CI [1.1–6.8], depression (ORadj 7.4 95% CI [2.3–24.1 and PTSD (ORadj 4.1 95% CI [1.1–14.6] at follow-up. Exposure to Hurricane Sandy has an impact on PTSD symptoms that persists over time. Given the likelihood of more frequent and intense hurricanes due to climate change, future hurricane recovery efforts must consider the long-term effects of hurricane exposure on mental health, especially on PTSD, when providing appropriate assistance and treatment.

  15. Aggregate-associated carbon and nitrogen in reclaimed sandy loam soils

    Energy Technology Data Exchange (ETDEWEB)

    Wick, A.F.; Stahl, P.D.; Ingram, L.J. [Virginia Polytechnic Institute & State University, Blacksburg, VA (United States)

    2009-11-15

    Minimal research has been conducted on aggregate, C, and N in coarse-textured soils used to reclaim surface coal mine lands. Furthermore, little is known about the contribution different plant communities make to the recovery of aggregation in these soils. Two chronosequences of semiarid reclaimed sites with sandy loam soils were sampled under shrub- and grass-dominated communities. Aggregation, aggregate fractions, and associated C and N were measured. No definitive trends of increasing macroaggregates between sites were observed undershrubs; however, macro- and microaggregation was greater in the 16-yr-old (0.20 and 0.23 kg aggregate kg{sup -1} soil, respectively) than in the 5-yr-old soils (0.02 and 0.08 kg aggregate kg{sup -1} soil, respectively) under grasses. Although C and N concentrations were drastically reduced (50-75%) with mining activity between the <1-yr-old and native soils, aggregate C and N concentrations tinder shrubs and grasses were similar to each other and to the native soils in the 5-yr-old site. Sods under grass in the 16-yr-old site had lower available and aggregate-occluded C and N concentrations than the 5-yr-old site, while C and N concentrations did not change between 5- and 16-yr-old soils under shrubs. Conversely, aggregate C and N pool sizes under shrubs and grasses both increased with site age to conditions similar to those observed in the native soil. Reclaimed shrub site soils had consistently higher C concentrations in the older reclaimed sites (10 and 16 yr old) than the soils under grasses, indicating greater accumulation and retention of C and N in organic material under shrub than grass communities in semiarid reclaimed sites.

  16. Emotional effects of dynamic textures

    NARCIS (Netherlands)

    Toet, A.; Henselmans, M.; Lucassen, M.P.; Gevers, T.

    2011-01-01

    This study explores the effects of various spatiotemporal dynamic texture characteristics on human emotions. The emotional experience of auditory (eg, music) and haptic repetitive patterns has been studied extensively. In contrast, the emotional experience of visual dynamic textures is still largely

  17. Effects of sodium polyacrylate on water retention and infiltration capacity of a sandy soil.

    Science.gov (United States)

    Zhuang, Wenhua; Li, Longguo; Liu, Chao

    2013-01-01

    Based on the laboratory study, the effects of sodium polyacrylate (SP) was investigated at 5 rates of 0, 0.08, 0.2, 0.5, and 1%, on water retention, saturated hydraulic conductivity(Ks), infiltration characteristic and water distribution profiles of a sandy soil. The results showed that water retention and available water capacity effectively increased with increasing SP rate. The Ks and the rate of wetting front advance and infiltration under certain pond infiltration was significantly reduced by increasing SP rate, which effectively reduced water in a sandy soil leaking to a deeper layer under the plough layer. The effect of SP on water distribution was obviously to the up layer and very little to the following deeper layers. Considering both the effects on water retention and infiltration capacity, it is suggested that SP be used to the sandy soil at concentrations ranging from 0.2 to 0.5%.

  18. Mineralogical and Micro-fabric investigation of the Sandy Facies of Opalinus Clay (Mont Terri)

    International Nuclear Information System (INIS)

    Kaufhold, Annette; Siegesmund, Siegfried; Dohrmann, Reiner; Graesle, Werner; Plischke, Ingo

    2013-01-01

    In the field of geological disposal of radioactive waste in many countries argillaceous formations are considered as potential host rock. For the understanding of the long-term behaviour of clay host rock, it is important to understand the interaction between mechanical behaviour, micro-fabric, and mineral composition. Previous publications showed that particularly the carbonate content and the arrangement of the carbonate grains (as cement in the matrix or as shells) determines the mechanical strength of Opalinus Clay and Callovo-Oxfordian Clay specimens, respectively. Klinkenberg et al. (2009) studied the shaly facies of Opalinus Clay, however, the actual deposit is planned to be built in the sandy facies of Opalinus Clay. The aim of the present study is to investigate the relation between micro-fabric, mineral composition, and mechanical properties of different samples derived from the sandy facies (BLT-A2). Image analysis showed that the carbonates in the sandy facies mainly occur as 1) matrix which in turn acts as cement. Carbonates also occur 2) in the fine sand fraction and 3) biogenic carbonates as traces. The carbonates of the sandy facies, therefore, appear to be similar to the carbonates of the Callovo-Oxfordian Clay with respect to their possible influence on failure strength. The mechanical testing showed that the shear strength increases with increasing carbonate content. This phenomenon was also observed for the samples of the Callovo-Oxfordian Clay, while the opposite relation was found for the shaly facies of the Opalinus Clay. Preliminary results presented here, indicate that the sandy facies (drilling BLT-A2) and Callovo-Oxfordian Clay show similar mechanical properties - in detail: 1) Micro-fabric: carbonates predominate in the matrix, 2) Mineralogy: high carbonate content and 3) Mechanical testing: shear strength increases with increasing carbonate content, where the type of carbonates which controls the increase of strength has to be

  19. Modeling Human Aesthetic Perception of Visual Textures

    NARCIS (Netherlands)

    Thumfart, Stefan; Jacobs, Richard H. A. H.; Lughofer, Edwin; Eitzinger, Christian; Cornelissen, Frans W.; Groissboeck, Werner; Richter, Roland

    Texture is extensively used in areas such as product design and architecture to convey specific aesthetic information. Using the results of a psychological experiment, we model the relationship between computational texture features and aesthetic properties of visual textures. Contrary to previous

  20. Replacement of Eocene white sandy limestone in historical buildings : over 100 years of practice in the Netherlands

    NARCIS (Netherlands)

    Quist, W.J.; Nijland, T.G.; Hees, R.P.J. van

    2013-01-01

    This paper discusses the replacement of white sandy limestone (Gobertange and Lede or Balegem) in the Netherlands in (successive) restorations from the mid-19th century onwards. White sandy limestone, transported from the southern part of the Low Countries (now Belgium), was extensively used in the

  1. Geochemical processes at a fresh/seawater interface in a shallow sandy aquifer

    DEFF Research Database (Denmark)

    Andersen, Martin Søgaard; Iversen, Vibeke Margrethe Nyvang; Postma, Diederik Jan

    2001-01-01

    Chemical processes in a natural fresh-/seawater mixing zone were studied in a shallow sandy aquifer. The dominant redox-processes are sulfate reduction and methanogenesis. Methanogenesis produces CO2, which causes calcite dissolution. The produced calcium induces ion exchange with sodium. The fin...... result of these interactions between different types of geochemical processes is an anoxic groundwater enriched in bicarbonate and sodium.......Chemical processes in a natural fresh-/seawater mixing zone were studied in a shallow sandy aquifer. The dominant redox-processes are sulfate reduction and methanogenesis. Methanogenesis produces CO2, which causes calcite dissolution. The produced calcium induces ion exchange with sodium. The final...

  2. Human versus artificial texture perception

    NARCIS (Netherlands)

    Petiet, Peter J.; van Erp, J.; Drullman, R.; van den Broek, Egon; Beintema, J.; van Wijngaarden, S.

    2006-01-01

    The performances of current texture analysis algorithms are still poor, especially when applied to a large, diffuse texture domain. Most of these purely computationally driven techniques are created to function within a highly restricted domain. When applied as computer vision techniques, frequently

  3. Health risk assessment linked to filling coastal quarries with treated dredged seaport sediments

    Energy Technology Data Exchange (ETDEWEB)

    Perrodin, Yves, E-mail: yves.perrodin@entpe.fr [Université de Lyon, ENTPE, UMR CNRS 5023, Laboratoire LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Donguy, Gilles [Université de Lyon, ENTPE, UMR CNRS 5023, Laboratoire LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Emmanuel, Evens [Laboratoire de Qualité de l' Eau et de l' Environnement, Université Quisqueya, BP 796 Port-au-Prince (Haiti); Winiarski, Thierry [Université de Lyon, ENTPE, UMR CNRS 5023, Laboratoire LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France)

    2014-07-01

    Dredged seaport sediments raise complex management problems since it is no longer possible to discharge them into the sea. Traditional waste treatments are poorly adapted for these materials in terms of absorbable volumes and cost. In this context, filling quarries with treated sediments appears interesting but its safety regarding human health must be demonstrated. To achieve this, a specific methodology for assessing health risks has been developed and tested on three seaport sediments. This methodology includes the development of a conceptual model of the global scenario studied and the definition of specific protocols for each of its major steps. The approach proposed includes in particular the use of metrological and experimental tools that are new in this context: (i) an experimental lysimeter for characterizing the deposit emissions, and (ii) a geological radar for identifying potential preferential pathways between the sediment deposit and the groundwater. The application of this approach on the three sediments tested for the scenario studied showed the absence of health risk associated with the consumption of groundwater for substances having a “threshold effect” (risk quotient < 1), and an acceptable risk for substances having a “non-threshold effect”, with the notable exception of arsenic (individual risk equal to 3.10{sup −6}). - Highlights: • The release of polluted dredged seaport sediments into the sea must be avoided. • Their use after treatment for the filling-up of quarries is proposed by managers. • An original health risk assessment methodology was created to validate this option. • It includes the use of a lysimeter and a georadar for the exposure assessment stage. • The example studied concludes to a health risk linked to arsenic in the groundwater.

  4. A Review Paper on Camouflage Texture Evaluation

    OpenAIRE

    Amol Patil; Girraj Prasad Rathode

    2013-01-01

    Traditional evaluation method of camouflage texture effect is subjective evaluation. It’s very tedious and inconvenient to direct the texture designing. In this project, a systemic and rational method for direction and evaluation of camouflage texture designing is proposed. Camouflage consists of things such as leaves, branches, or brown and green paint, which are used to make it difficult for an enemy to see military forces and equipment. A camouflage texture evaluation method based on WSSIM...

  5. Environmental rehabilitation of dismissed quarry areas in the Emilia Apennines (Italy) based on the exploitation of geosites

    Science.gov (United States)

    Soldati, Mauro; Coratza, Paola; Vandelli, Vittoria

    2016-04-01

    The landscape modifications induced by human activity in the past 50 years, due to quarrying in the catchment of Rio della Rocca (Province of Reggio Emilia, northern Italy) and plans for its environmental rehabilitation, are illustrated. The study area is located in the northern Apennines margin, specifically in the municipality of Castellarano, and is characterised by a great variety of abiotic environments and high biodiversity. As regards the geological aspects of the area, the main lithological outcrops consists of yellow sandstones belonging to the Epi-Ligurian Sequence (Upper Eocene - Lower Oligocene) and grey clays (Lower Pliocene - Lower Pleistocene) of the marine units of the Apennine margin. From a geomorphological viewpoint, the landscape evolution of this valley has been deeply influenced by the presence of rocks with different mechanical behaviour, gravitational and rainwash processes and, more recently, human activities. The latter have played a fundamental role in modelling the physical landscape of the area in recent times. In the Sassuolo area (Province of Modena), very close to the study area, there is the largest tile making district in the world, which was developed during the '60s and '70s of the 20th century, partly thanks to the wide availability of clayey raw materials with suitable technological properties. Since the mid-1950s the study area has been affected by intense quarrying activities which have largely modified its environmental and, in particular, geomorphological features. In the 1970s, three clay pits and four sandstone quarries were active in the area. The clay pits were used for tile production whereas the sandstone materials were utilised in large part for the building industry. This production scenario has radically changed during the past twenty years, with the progressive abandonment of quarries due to the introduction of ever-more restrictive environmental policies, imposing rigorous planning on mining activities

  6. Effects of initial microstructure and texture on microstructure, texture evolution and magnetic properties of non-oriented electrical steel

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Hai-Tao, E-mail: liuht@ral.neu.edu.cn [State Key Laboratory of Rolling and Automation, Northeastern University, P.O. Box 105, Shenyang 110819 (China); Institute of Research of Iron and Steel, Shasteel, Zhangjiagang 215625, Jiangsu (China); Li, Hua-Long [Institute of Research of Iron and Steel, Shasteel, Zhangjiagang 215625, Jiangsu (China); Wang, Hui [Science and Technology on Surface Physics and Chemistry Laboratory, P.O. Box No. 9-35, Huafengxincun, Jiangyou City, Sichuan Province 621908 (China); National Key Laboratory for Nuclear Fuel and Materials, Nuclear Power Institute of China, Chengdu 610041 (China); Liu, Yi; Gao, Fei; An, Ling-Zi; Zhao, Shi-Qi; Liu, Zhen-Yu; Wang, Guo-Dong [State Key Laboratory of Rolling and Automation, Northeastern University, P.O. Box 105, Shenyang 110819 (China)

    2016-05-15

    An equiaxed grained as-cast strip and a columnar grained as-cast strip was produced by using twin-roll strip casting, respectively. Both as-cast strips mainly containing 0.71 wt%Si and 0.44 wt%Al were cold rolled and annealed with or without the hot rolling prior to cold rolling. Microstructure, texture evolution along the whole processing routes and the magnetic properties were investigated in detail. It was found that the equiaxed grained strip was characterized by almost random texture while the columnar grained strip was dominated by strong λ-fiber (<001>‖ND) texture. After cold rolling and annealing, all the final sheets of both the as-cast strips showed extremely weak γ-fiber (<111>‖ND) recrystallization texture. In addition, the finally annealed sheets of the equiaxed grained strip were dominated by relatively weak λ-fiber and strong Goss ({110}<001>) recrystallization texture while those of the columnar grained strip were dominated by much stronger λ-fiber and much weaker Goss recrystallization texture regardless of whether the hot rolling was adopted before cold rolling, thus the former showed much lower magnetic induction than the latter. On the other hand, even though the finally annealed sheets of the equiaxed grained strip showed a little more homogeneous recrystallization microstructure with a little bigger grain size than those of the columnar grained strip in the case of no hot rolling, a much higher iron loss was displayed. By contrast, in the case of hot rolling, the former exhibited a little lower iron loss than the latter as a result of the more significant increase in grain size and λ-fiber recrystallization texture. The introduction of the hot rolling could increase the grain size, strengthen λ-fiber texture and weaken Goss texture of the finally annealed sheets of both the as-cast strips, leading to a much improvement in both the magnetic induction and iron loss. - Highlights: • Equiaxed and columnar grained as-cast strips were

  7. Bayesian exploration for intelligent identification of textures

    Directory of Open Access Journals (Sweden)

    Jeremy A. Fishel

    2012-06-01

    Full Text Available In order to endow robots with humanlike abilities to characterize and identify objects, they must be provided with tactile sensors and intelligent algorithms to select, control and interpret data from useful exploratory movements. Humans make informed decisions on the sequence of exploratory movements that would yield the most information for the task, depending on what the object may be and prior knowledge of what to expect from possible exploratory movements. This study is focused on texture discrimination, a subset of a much larger group of exploratory movements and percepts that humans use to discriminate, characterize, and identify objects. Using a testbed equipped with a biologically inspired tactile sensor (the BioTac® we produced sliding movements similar to those that humans make when exploring textures. Measurement of tactile vibrations and reaction forces when exploring textures were used to extract measures of textural properties inspired from psychophysical literature (traction, roughness, and fineness. Different combinations of normal force and velocity were identified to be useful for each of these three properties. A total of 117 textures were explored with these three movements to create a database of prior experience to use for identifying these same textures in future encounters. When exploring a texture, the discrimination algorithm adaptively selects the optimal movement to make and property to measure based on previous experience to differentiate the texture from a set of plausible candidates, a process we call Bayesian exploration. Performance of 99.6% in correctly discriminating pairs of similar textures was found to exceed human capabilities. Absolute classification from the entire set of 117 textures generally required a small number of well-chosen exploratory movements (median=5 and yielded a 95.4% success rate. The method of Bayesian exploration developed and tested in this paper may generalize well to other

  8. Long-Term Exposure to Silica Dust and Risk of Total and Cause-Specific Mortality in Chinese Workers: A Cohort Study

    OpenAIRE

    Chen, Weihong; Liu, Yuewei; Wang, Haijiao; Hnizdo, Eva; Sun, Yi; Su, Liangping; Zhang, Xiaokang; Weng, Shaofan; Bochmann, Frank; Hearl, Frank J.; Chen, Jingqiong; Wu, Tangchun

    2012-01-01

    Editors' Summary Background Walk along most sandy beaches and you will be walking on millions of grains of crystalline silica, one of the commonest minerals on earth and a major ingredient in glass and in ceramic glazes. Silica is also used in the manufacture of building materials, in foundry castings, and for sandblasting, and respirable (breathable) crystalline silica particles are produced during quarrying and mining. Unfortunately, silica dust is not innocuous. Several serious diseases ar...

  9. Use of a Combination of Vertical and Horizontal Boreholes in Massive Blasting of Benches in the Surface Quarry Rodež

    Directory of Open Access Journals (Sweden)

    Tori Matija

    2017-12-01

    Full Text Available This article deals with the extraction of minerals (limestone/marl/flysch in the quarry Rodež, which is located in western Slovenia. During the extraction of minerals in a quarry, drilling and blasting of benches are used. The focus of the article is on the analysis of the parameters related to drilling and blasting in surface excavations when using a combination of explosions and introducing horizontal wells along with vertical holes in the bench. On the basis of the analysis of basic parameters through a combination of drilling horizontal wells and charging those with the ammonal + Anfex explosive, analyses of effects of seismic disturbances on potentially affected buildings have also been conducted. The article is connected to and deals exclusively with the basic parameters of drilling and blasting, with the introduction of horizontal drilling and with the analysis of seismic measurements of threatened buildings in accordance with the German standard German Institute for Standardisation (DIN 4150 during the use of a new method of blasting.

  10. 2012 USACE Post Sandy Topographic LiDAR: Virginia and Maryland

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — TASK ORDER NAME: VIRGINIA AND MARYLAND LIDAR ACQUISITION FOR SANDY RESPONSE CONTRACT NUMBER: W912P9-10-D-0533 TASK ORDER NUMBER: W81C8X2314841 Woolpert Project...

  11. BREAD CRUMBS TEXTURE OF SPELT

    Directory of Open Access Journals (Sweden)

    Joanna Korczyk – Szabó

    2014-02-01

    Full Text Available Texture analysis is an objective physical examination of baked products and gives direct information on the product quality, oppositely to dough rheology tests what inform on the baking suitability of the flour, as raw material. Evaluation of the mechanical properties of bread crumb is important not only for quality assurance in the bakeries, but also for assessing the effects of changes in dough ingredients and processing condition and also for describing the changes in bread crumb during storage. Crumb cellular structure is an important quality criterion used in commercial baking and research laboratories to judge bread quality alongside taste, crumb colour and crumb physical texture. In the framework of our research during the years 2010 – 2011 were analyzed selected indicators of bread crumb for texture quality of three Triticum spelta L. cultivars – Altgold, Rubiota and Ostro grown in an ecological system. The bread texture quality was evaluated on texture analyzer TA.XT Plus (Stable Micro Systems, Surrey, UK, following the AACC (74-09 standard and expressed as crumb firmness (N, stiffness (N.mm-1 and relative elasticity (%. Our research proved that all selected indicators were significantly influenced by the year of growing and variety. The most soft bread was achieved in Rubiota, whereas bread crumb samples from Altgold and Ostro were the most firm and stiff. Correlation analysis showed strong negative correlation between relative elasticity and bread crumb firmness as well as bread stiffness (-0.65++, -0.66++. The spelt wheat bread crumb texture need further investigation as it can be a reliable quality parameter.

  12. Quantitative Characterisation of Surface Texture

    DEFF Research Database (Denmark)

    De Chiffre, Leonardo; Lonardo, P.M.; Trumpold, H.

    2000-01-01

    This paper reviews the different methods used to give a quantitative characterisation of surface texture. The paper contains a review of conventional 2D as well as 3D roughness parameters, with particular emphasis on recent international standards and developments. It presents new texture...

  13. Fast Synthesis of Dynamic Colour Textures

    Czech Academy of Sciences Publication Activity Database

    Filip, Jiří; Haindl, Michal; Chetverikov, D.

    -, č. 66 (2006), s. 53-54 ISSN 0926-4981 R&D Projects: GA AV ČR IAA2075302; GA AV ČR 1ET400750407; GA MŠk 1M0572 EU Projects: European Commission(XE) 507752 - MUSCLE Institutional research plan: CEZ:AV0Z10750506 Keywords : dynamic colour texture * texture synthesis * texture modelling Subject RIV: BD - Theory of Information http://www.ercim.org/publication/Ercim_News/enw66/haindl.html

  14. Correlation between macro texture measures carried out by the volumetric method and by different laser texture meter

    International Nuclear Information System (INIS)

    Parra Ruiz, L.; Yanguas Gonzalez, S. J.

    2013-01-01

    The reference value for the measurement of surface macro texture in the Spanish Main Road Network is the MTD or Mean Texture Depth (PMT, Profundidad Media de Textura), obtained by means of the volumetric methods, in accordance with the standard UNE EN 13036-1:12010. The fact that it is a spot measurement that requires road closures makes it an expensive procedure as well as slow and dangerous. In addition to this, the test results are relatively sensitive to the operator, being the procedure not too suitable for systematic surveys. These are some of the reasons that have contributed to the development of texture meter laser devices that can be assembled on board of vehicles, circulating without interfering with the normal traffic flow and providing a parameter named the MPD (Mean Depth Profile). According to the standard UNE-EN ISO 13473-1:2006, it is possible to estimate the texture obtained by volumetric methods, with the parameter ETD (Estimated Texture Depth) through the equation: ETD=0,8 x MPD+0.2 In 2008 CEDEX conducted a study that correlated macro texture measures obtained by means of the volumetric method with such carried out by different laser texture meters. The equations yield a better relation between MPD and MTD were dependent on the measurement device used and were not linear equations type, as is it indicated in the standard, but exponential type equations. (Author) 6 refs.

  15. Epitaxial hexagonal materials on IBAD-textured substrates

    Energy Technology Data Exchange (ETDEWEB)

    Matias, Vladimir; Yung, Christopher

    2017-08-15

    A multilayer structure including a hexagonal epitaxial layer, such as GaN or other group III-nitride (III-N) semiconductors, a <111> oriented textured layer, and a non-single crystal substrate, and methods for making the same. The textured layer has a crystalline alignment preferably formed by the ion-beam assisted deposition (IBAD) texturing process and can be biaxially aligned. The in-plane crystalline texture of the textured layer is sufficiently low to allow growth of high quality hexagonal material, but can still be significantly greater than the required in-plane crystalline texture of the hexagonal material. The IBAD process enables low-cost, large-area, flexible metal foil substrates to be used as potential alternatives to single-crystal sapphire and silicon for manufacture of electronic devices, enabling scaled-up roll-to-roll, sheet-to-sheet, or similar fabrication processes to be used. The user is able to choose a substrate for its mechanical and thermal properties, such as how well its coefficient of thermal expansion matches that of the hexagonal epitaxial layer, while choosing a textured layer that more closely lattice matches that layer.

  16. Texture-dependent effects of pseudo-chewing sound on perceived food texture and evoked feelings in response to nursing care foods.

    Science.gov (United States)

    Endo, Hiroshi; Ino, Shuichi; Fujisaki, Waka

    2017-09-01

    Because chewing sounds influence perceived food textures, unpleasant textures of texture-modified diets might be improved by chewing sound modulation. Additionally, since inhomogeneous food properties increase perceived sensory intensity, the effects of chewing sound modulation might depend on inhomogeneity. This study examined the influences of texture inhomogeneity on the effects of chewing sound modulation. Three kinds of nursing care foods in two food process types (minced-/puréed-like foods for inhomogeneous/homogeneous texture respectively) were used as sample foods. A pseudo-chewing sound presentation system, using electromyogram signals, was used to modulate chewing sounds. Thirty healthy elderly participants participated in the experiment. In two conditions with and without the pseudo-chewing sound, participants rated the taste, texture, and evoked feelings in response to sample foods. The results showed that inhomogeneity strongly influenced the perception of food texture. Regarding the effects of the pseudo-chewing sound, taste was less influenced, the perceived food texture tended to change in the minced-like foods, and evoked feelings changed in both food process types. Though there were some food-dependent differences in the effects of the pseudo-chewing sound, the presentation of the pseudo-chewing sounds was more effective in foods with an inhomogeneous texture. In addition, it was shown that the pseudo-chewing sound might have positively influenced feelings. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Uncertainties in sandy shorelines evolution under the Bruun rule assumption

    Directory of Open Access Journals (Sweden)

    Gonéri eLe Cozannet

    2016-04-01

    Full Text Available In the current practice of sandy shoreline change assessments, the local sedimentary budget is evaluated using the sediment balance equation, that is, by summing the contributions of longshore and cross-shore processes. The contribution of future sea-level-rise induced by climate change is usually obtained using the Bruun rule, which assumes that the shoreline retreat is equal to the change of sea-level divided by the slope of the upper shoreface. However, it remains unsure that this approach is appropriate to account for the impacts of future sea-level rise. This is due to the lack of relevant observations to validate the Bruun rule under the expected sea-level rise rates. To address this issue, this article estimates the coastal settings and period of time under which the use of the Bruun rule could be (invalidated, in the case of wave-exposed gently-sloping sandy beaches. Using the sedimentary budgets of Stive (2004 and probabilistic sea-level rise scenarios based on IPCC, we provide shoreline change projections that account for all uncertain hydrosedimentary processes affecting idealized coasts (impacts of sea-level rise, storms and other cross-shore and longshore processes. We evaluate the relative importance of each source of uncertainties in the sediment balance equation using a global sensitivity analysis. For scenario RCP 6.0 and 8.5 and in the absence of coastal defences, the model predicts a perceivable shift toward generalized beach erosion by the middle of the 21st century. In contrast, the model predictions are unlikely to differ from the current situation in case of scenario RCP 2.6. Finally, the contribution of sea-level rise and climate change scenarios to sandy shoreline change projections uncertainties increases with time during the 21st century. Our results have three primary implications for coastal settings similar to those provided described in Stive (2004 : first, the validation of the Bruun rule will not necessarily be

  18. Hurricane Sandy: An Educational Bibliography of Key Research Studies

    Science.gov (United States)

    Piotrowski, Chris

    2013-01-01

    There, undoubtedly, will be a flurry of research activity in the "Superstorm" Sandy impact area on a myriad of disaster-related topics, across academic disciplines. The purpose of this study was to review the disaster research related specifically to hurricanes in the educational and social sciences that would best serve as a compendium…

  19. Organisms associated with the sandy-beach bivalve Donax serra ...

    African Journals Online (AJOL)

    57: 134-136. BROWN, AC. & WEBB, S.c. 1994. Organisms associated \\.,.,ith burrowing whelks of the genus Bullia. S Afr. 1. Zool. 29: 144-151. BROWN, A.C., STENTON-DOZEY, J.~.E. & TRUEMAN, E.R.. 1989. Sandy-beach bivalves and gastropods; a comparison between Donax serra and Ruilia digitalis. Adv. mar. Bioi. 25:.

  20. Hurricane Sandy Exposure Alters the Development of Neural Reactivity to Negative Stimuli in Children.

    Science.gov (United States)

    Kessel, Ellen M; Nelson, Brady D; Kujawa, Autumn; Hajcak, Greg; Kotov, Roman; Bromet, Evelyn J; Carlson, Gabrielle A; Klein, Daniel N

    2018-03-01

    This study examined whether exposure to Hurricane Sandy-related stressors altered children's brain response to emotional information. An average of 8 months (M age  = 9.19) before and 9 months after (M age  = 10.95) Hurricane Sandy, 77 children experiencing high (n = 37) and low (n = 40) levels of hurricane-related stress exposure completed a task in which the late positive potential, a neural index of emotional reactivity, was measured in response to pleasant and unpleasant, compared to neutral, images. From pre- to post-Hurricane Sandy, children with high stress exposure failed to show the same decrease in emotional reactivity to unpleasant versus neutral stimuli as those with low stress exposure. Results provide compelling evidence that exposure to natural disaster-related stressors alters neural emotional reactivity to negatively valenced information. © 2016 The Authors. Child Development © 2016 Society for Research in Child Development, Inc.

  1. Superstorm Sandy: How the New York University Psychiatry Residency Training Program Weathered the Storm.

    Science.gov (United States)

    Capasso, Rebecca; Adler, Laura

    2016-10-01

    The teaching hospitals of the New York University psychiatry residency program were evacuated and then closed for a minimum of 3 months in the aftermath of Superstorm Sandy. Faculty and residents were deployed to alternate clinical sites. The authors examine the consequences of Superstorm Sandy and its implications for the New York University psychiatry residency training program. A survey was administered to faculty and residents. The authors tabulated 98 surveys, for which 24 % of faculty and 84 % of residents responded. Among respondents, 61 % believed that being involved in the evacuation of the hospitals was a positive experience. During deployment, most (85 %) found being placed with peers and supervisors to be beneficial, but there were significant disruptions. Despite facing multiple challenges including closed facilities, deployment to nonaffiliated hospitals, and exhausted personal resources, the training program continued to provide accredited clinical experiences, a core curriculum, and supervision for psychiatry residents during and after Superstorm Sandy.

  2. CONTRIBUTIONS TO IMPROVING CULTURE TEHNOLOGIES OF PEACHES GROWN ON SANDY SOILS THE SOUTH OF OLTENIA

    Directory of Open Access Journals (Sweden)

    Anica Durau

    2013-12-01

    Full Text Available Technological factors with major implications in obtaining high yields and quality in peaches grown on sandy soils are planting row distance and shape of the crown, soil maintenance system, chemical, organic and foliar fertilzation. A smal size combined with the flatening of the crowns of the tres alows a dense planting, also ensure proper mechanization of work and easy penetration of light to the leaves and fruits. Crown form vertical belt proved to be suitable for al planting distances studied, easily made and maintained, having fruit production ranged betwen 15.9 t / ha at a distance of 2 m, 10.3 t / ha at a distance of 2.5 m and 7.9 t / ha at a distance of 3 m. The state of soil nutrient supply influence sucesful peach crop on sandy soils. The fertilzer dose of technology to N10 P80 K10 kg s.a / ha production was 34.9 t / ha. Organic fertilzation also contributes to obtaining high yields of peach. In sandy soil conditions most fruit production of 9.6 t / ha was obtained by fertilzation with organic manure 60t/ha. Besides fertilzation, soil maintenance system is one important link in the technology peach crop on sandy soils. The results found that the biggest peach fruit production was obtained from field maintenance system black-8,2t/ha. Using technology in foliar peaches culture on sandy soils, is an important means of providing nutrients that lead to improved proceses of growth and fructification. The best way is with foliar fertilzation Folibor in dose 5l/ha, the production obtained was 12.4 t /ha.

  3. Quantifying the synergistic effect of the precipitation and land use on sandy desertification at county level: a case study in Naiman Banner, Northern China.

    Science.gov (United States)

    Xiaodong, Ge; Jinren, Ni; Zhenshan, Li; Ronggui, Hu; Xin, Ming; Qing, Ye

    2013-07-15

    Assessing the driving forces of sandy desertification is fundamental and important for its control. It has been widely accepted that both climatic conditions and land use have great impact on sandy desertification in northern China. However, the relative role and synergistic effect of each driving force of sandy desertification are still not clear. In this paper, an indicator named as SI was defined to represent the integrated probability of sandy desertification caused by land use. A quantitative method was developed for characterizing the relative roles of annual precipitation and land use to sandy desertification in both spatial and temporal dimensions at county level. Results showed that, at county level, land use was the main cause of sandy desertification for Naiman Banner since 1987-2009. In the case of spatial dimension, the different combination of land use types decided the distribution of sandy desertification probability and finally decided the spatial pattern of bared sand land. In the case of temporal dimension, the synergistic effect of land use and precipitation highly influenced the spatial distribution of sandy desertification. Copyright © 2013 Elsevier Ltd. All rights reserved.

  4. Expanded uncertainty estimation methodology in determining the sandy soils filtration coefficient

    Science.gov (United States)

    Rusanova, A. D.; Malaja, L. D.; Ivanov, R. N.; Gruzin, A. V.; Shalaj, V. V.

    2018-04-01

    The combined standard uncertainty estimation methodology in determining the sandy soils filtration coefficient has been developed. The laboratory researches were carried out which resulted in filtration coefficient determination and combined uncertainty estimation obtaining.

  5. Evaluation of color representation for texture analysis

    NARCIS (Netherlands)

    Verbrugge, R.; van den Broek, Egon; van Rikxoort, E.M.; Taatgen, N.; Schomaker, L.

    2004-01-01

    Since more than 50 years texture in image material is a topic of research. Hereby, color was ignored mostly. This study compares 70 different configurations for texture analysis, using four features. For the configurations we used: (i) a gray value texture descriptor: the co-occurrence matrix and a

  6. An Experimental Study of Portland Cement and Superfine Cement Slurry Grouting in Loose Sand and Sandy Soil

    Directory of Open Access Journals (Sweden)

    Weijing Yao

    2018-04-01

    Full Text Available Grouting technology is widely applied in the fields of geotechnical engineering in infrastructure. Loose sand and sandy soil are common poor soils in tunnel and foundation treatments. It is necessary to use superfine cement slurry grouting in the micro-cracks of soil. The different effectiveness of Portland cement slurry and superfine cement slurry in sandy soil by the laboratory grouting experiment method were presented in this paper. The grouting situations of superfine cement slurry injected into sand and sandy soil were explored. The investigated parameters were the dry density, wet density, moisture content, internal friction angle, and cohesion force. The results show that the consolidation effect of superfine cement is better than that of Portland cement due to the small size of superfine cement particles. The superfine cement can diffuse into the sand by infiltration, extrusion, and splitting. When the water–cement ratio of superfine cement slurry is less than 2:1 grouting into loose sand, the dry and wet density decrease with the increase in the water–cement ratio, while the moisture content and cohesive force gradually increase. When the water–cement ratio of superfine cement slurry is 1:1 grouting into loose sand and sandy soil, the dry density, wet density, and cohesive force of loose sand are larger than those of sandy soil. The results of the experiment may be relevant for engineering applications.

  7. Orbital selective spin-texture in a topological insulator

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Bahadur, E-mail: bahadursingh24@gmail.com; Prasad, R. [Department of Physics, Indian Institute of Technology Kanpur, Kanpur 208016 (India)

    2015-05-15

    Three-dimensional topological insulators support a metallic non-trivial surface state with unique spin texture, where spin and momentum are locked perpendicular to each other. In this work, we investigate the orbital selective spin-texture associated with the topological surface states in Sb2Te{sub 3}, using the first principles calculations. Sb2Te{sub 3} is a strong topological insulator with a p-p type bulk band inversion at the Γ-point and supports a single topological metallic surface state with upper (lower) Dirac-cone has left (right) handed spin-texture. Here, we show that the topological surface state has an additional locking between the spin and orbitals, leading to an orbital selective spin-texture. The out-of-plane orbitals (p{sub z} orbitals) have an isotropic orbital texture for both the Dirac cones with an associated left and right handed spin-texture for the upper and lower Dirac cones, respectively. In contrast, the in-planar orbital texture (p{sub x} and p{sub y} projections) is tangential for the upper Dirac-cone and is radial for the lower Dirac-cone surface state. The dominant in-planar orbital texture in both the Dirac cones lead to a right handed orbital-selective spin-texture.

  8. Heterogeneous patterns enhancing static and dynamic texture classification

    International Nuclear Information System (INIS)

    Silva, Núbia Rosa da; Martinez Bruno, Odemir

    2013-01-01

    Some mixtures, such as colloids like milk, blood, and gelatin, have homogeneous appearance when viewed with the naked eye, however, to observe them at the nanoscale is possible to understand the heterogeneity of its components. The same phenomenon can occur in pattern recognition in which it is possible to see heterogeneous patterns in texture images. However, current methods of texture analysis can not adequately describe such heterogeneous patterns. Common methods used by researchers analyse the image information in a global way, taking all its features in an integrated manner. Furthermore, multi-scale analysis verifies the patterns at different scales, but still preserving the homogeneous analysis. On the other hand various methods use textons to represent the texture, breaking texture down into its smallest unit. To tackle this problem, we propose a method to identify texture patterns not small as textons at distinct scales enhancing the separability among different types of texture. We find sub patterns of texture according to the scale and then group similar patterns for a more refined analysis. Tests were performed in four static texture databases and one dynamical one. Results show that our method provide better classification rate compared with conventional approaches both in static and in dynamic texture.

  9. The Department of the Interior Strategic Sciences Group and its Response to Hurricane Sandy

    Science.gov (United States)

    Ludwig, K. A.; Machlis, G. E.; Applegate, D.

    2013-12-01

    This presentation will describe the history, mission, and current activities of the newly formed Department of the Interior (DOI) Strategic Sciences Group (SSG), with a focus on its response to Hurricane Sandy and lessons learned from using scenario building to support decision making. There have been several environmental crises of national significance in recent years, including Hurricane Katrina (2005), large-scale California wildfires (2007-2008), the Deepwater Horizon oil spill (2010), and Hurricane Sandy (2012). Such events are complex because of their impacts on the ecology, economy, and people of the affected locations. In these and other environmental disasters, the DOI has had significant responsibilities to protect people and resources and to engage in emergency response, recovery, and restoration efforts. In recognition of the increasingly critical role of strategic science in responding to such complex events, the DOI established the SSG by Secretarial Order in 2012. Its purpose is to provide the DOI with science-based assessments and interdisciplinary scenarios of environmental crises affecting Departmental resources; rapidly assemble interdisciplinary teams of scientists from government, academia, and non-governmental organizations to conduct such work; and provide results to DOI leadership as usable knowledge to support decision making. March 2013 was the SSG's first deployment since its formation. The SSG's charge was to support DOI's participation on the Hurricane Sandy Rebuilding Task Force by developing scenarios of Hurricane Sandy's environmental, economic, and social consequences in the New York/New Jersey area and potential interventions that could improve regional resilience to future major storms. Over the course of one week, the SSG Sandy team (Operational Group Sandy) identified 13 first-tier consequences and 17 interventions. The SSG briefed DOI leadership, Task Force representatives, and other policy makers in both Washington, DC and

  10. Constraining Depositional Slope From Sedimentary Structures in Sandy Braided Streams

    Science.gov (United States)

    Lynds, R. M.; Mohrig, D.; Heller, P. L.

    2003-12-01

    Determination of paleoslopes in ancient fluvial systems has potentially broad application to quantitatively constraining the history of tectonics and paleoclimate in continental sequences. Our method for calculating paleoslopes for sandy braided streams is based upon a simple physical model that establishes depositional skin-frictional shear stresses from assemblages of sedimentary structures and their associated grain size distributions. The addition of a skin-frictional shear stress, with a geometrically determined form-drag shear stress results in a total boundary shear stress which is directly related to water-surface slope averaged over an appropriate spatial scale. In order to apply this model to ancient fluvial systems, it is necessary to measure the following: coarsest suspended sediment size, finest grain size carried in bed load, flow depth, dune height, and dune length. In the rock record, suspended load and bed load can be accurately assessed by well-preserved suspended load deposits ("low-energy" ripples) and bed load deposits (dune foresets). This model predicts an average slope for the North Loup River near Taylor, Nebraska (modern case study) of 2.7 x 10-3. The measured reach-averaged water surface slope for the same reach of the river is 1.37 x 10-3. We suggest that it is possible to calculate the depositional slope of a sandy fluvial system by a factor of approximately two. Additionally, preliminary application of this model to the Lower Jurassic Kayenta Formation throughout the Colorado Plateau provides a promising and consistent evaluation of paleoslope in an ancient and well-preserved, sandy braided stream deposit.

  11. Texture analyses of Sauropod dinosaur bones from Tendaguru

    International Nuclear Information System (INIS)

    Pyzalla, A.R.; Sander, P.M.; Hansen, A.; Ferreyro, R.; Yi, S.-B.; Stempniewicz, M.; Brokmeier, H.-G.

    2006-01-01

    The apatite texture of fossil Brachiosaurus brancai and Barosaurus africanus sauropod bones from the excavation site at Tendaguru, Tanzania, was characterized by neutron diffraction pole figures. The results obtained reveal predominantly -fibre textures of the apatite; the fibre direction coincides with the longitudinal direction of the long bones of the skeletons. Neutron pole figures further indicate that other texture types may also be present. Texture strength is similar to dinosaur tendons and contemporary turkey tendon studied by others. Variations of texture strength across the bone wall cross-sections are not significantly large

  12. Evolution of the soil humus status on the calcareous Neogene clay dumps of the Sokolov quarry complex in the Czech Republic

    Czech Academy of Sciences Publication Activity Database

    Abakumov, E.V.; Frouz, Jan

    2009-01-01

    Roč. 42, č. 7 (2009), s. 718-724 ISSN 1064-2293 Grant - others:Russian Foundation for Basic Research(XE) 08-04-01128 Institutional research plan: CEZ:AV0Z60660521 Keywords : soil humus status * calcareous Neogene clay dumps * Sokolov quarry complex Subject RIV: EH - Ecology, Behaviour Impact factor: 0.222, year: 2009

  13. Disentangling diversity patterns in sandy beaches along environmental gradients.

    Science.gov (United States)

    Barboza, Francisco R; Gómez, Julio; Lercari, Diego; Defeo, Omar

    2012-01-01

    Species richness in sandy beaches is strongly affected by concurrent variations in morphodynamics and salinity. However, as in other ecosystems, different groups of species may exhibit contrasting patterns in response to these environmental variables, which would be obscured if only aggregate richness is considered. Deconstructing biodiversity, i.e. considering richness patterns separately for different groups of species according to their taxonomic affiliation, dispersal mode or mobility, could provide a more complete understanding about factors that drive species richness patterns. This study analyzed macroscale variations in species richness at 16 Uruguayan sandy beaches with different morphodynamics, distributed along the estuarine gradient generated by the Rio de la Plata over a 2 year period. Species richness estimates were deconstructed to discriminate among taxonomic groups, supralittoral and intertidal forms, and groups with different feeding habits and development modes. Species richness was lowest at intermediate salinities, increasing towards oceanic and inner estuarine conditions, mainly following the patterns shown for intertidal forms. Moreover, there was a differential tolerance to salinity changes according to the habitat occupied and development mode, which determines the degree of sensitivity of faunal groups to osmotic stress. Generalized (additive and linear) mixed models showed a clear increase of species richness towards dissipative beaches. All taxonomic categories exhibited the same trend, even though responses to grain size and beach slope were less marked for crustaceans and insects than for molluscs or polychaetes. However, supralittoral crustaceans exhibited the opposite trend. Feeding groups decreased from dissipative to reflective systems, deposit feeders being virtually absent in the latter. This deconstructive approach highlights the relevance of life history strategies in structuring communities, highlighting the relative

  14. Copper and zinc distribution coefficients for sandy aquifer materials

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Astrup, Thomas; Boddum, J. K.

    2000-01-01

    Distribution coe�cients (Kd) were measured for copper (Cu) and zinc (Zn) in laboratory batch experiments for 17 sandy aquifer materials at environmentally relevant solute concentrations (Cu: 5±300 mg/l, Zn: 20±3100 mg/l). The Kd values ranged two to three orders of magnitude (Cu: 70±10,800 l/ kg...

  15. Amelioration of sandy soils in drought stricken areas through use of ...

    African Journals Online (AJOL)

    ACSS

    improving N, P, Ca and Mg content in sandy soils, and consequently support crop growth and yield. ... stress, soil moisture conservation, soil fertility management ... water many times its own weight. ... improves the productivity of degraded,.

  16. DETERMINATION OF THERMAL RESPONSE OF CARRARA AND SNEZNIKOVSKY MARBLE USED AS A BUILDING MATERIALS

    Directory of Open Access Journals (Sweden)

    Veronika Petráňová

    2016-02-01

    Full Text Available Physical weathering of marble, widely used as a cladding material on buildings, is one of the most common damaging mechanism caused by anisotropic thermal expansion of calcite grains. The extent of marble deterioration depends mainly on stone fabric and texture. Dry cuboids of Carrara marble and marble from Dolni Morava quarry were subjected to microscopic analysis and thermal cycling, to determine the thermal expansion related to stone fabric and predominant lattice orientation of grains (i.e. texture.

  17. Automatic Texture Optimization for 3D Urban Reconstruction

    Directory of Open Access Journals (Sweden)

    LI Ming

    2017-03-01

    Full Text Available In order to solve the problem of texture optimization in 3D city reconstruction by using multi-lens oblique images, the paper presents a method of seamless texture model reconstruction. At first, it corrects the radiation information of images by camera response functions and image dark channel. Then, according to the corresponding relevance between terrain triangular mesh surface model to image, implements occlusion detection by sparse triangulation method, and establishes the triangles' texture list of visible. Finally, combines with triangles' topology relationship in 3D triangular mesh surface model and means and variances of image, constructs a graph-cuts-based texture optimization algorithm under the framework of MRF(Markov random filed, to solve the discrete label problem of texture optimization selection and clustering, ensures the consistency of the adjacent triangles in texture mapping, achieves the seamless texture reconstruction of city. The experimental results verify the validity and superiority of our proposed method.

  18. Investigation of intact rock geomechanical parameters' effects on commercial blocks' productivity within stone reserves: A case history of some quarries in Isfahan, Iran

    Science.gov (United States)

    Yarahmadi, Reza; Bagherpour, Raheb; Tabaei, Morteza; Sousa, Luis M. O.

    2017-10-01

    One of the common methods to determine commercial blocks productivity (CBP) in reserves of dimension stone is through the study of the discontinuities' network. However, this determination remains a difficult task due to geographical heterogeneity and lack of access to all reserves' formations. This study presents a new method based on various geomechanical tests performed on intact rocks that assessed the CBP of a dimension stones' rock mass. Assuming that a dimension stone's rock mass comprised a large block of an intact rock, due to tectonics, the geomechanical properties of this block had direct effects on the discontinuities created within it. Therefore, the geomechanical properties of the intact rock may be related to the CBP of a stone reserve. Based on this factor, this study explored the relationship among some geomechanical properties, including failure angle, uniaxial compressive strength, and modulus of elasticity, and CBP by using data acquired from 21 dimension stone quarries consisting of travertine, marble, and onyx groups. According to the results obtained from the analysis of the Isfahan province's Iranian quarries, failure angle was not highly related to the reserve's CBP. In marble quarries, CBP may decrease, if the compressive strength of an intact rock exceeds 60 MPa. Among the studied parameters, the saturated-to-dry ratio's modulus of elasticity had the greatest relationship to the CBP. Generally, the presented diagrams displayed that the correlation between geomechanical properties and the CBP were an appropriate guide in determining the potential cost-effectiveness of a accessing a particular rock reserve during the early exploration phase.

  19. Roma İmparatorluk Mermer Ocaklarında Yazıt Kullanımı ve Bazı Ünik ÖrneklerInscriptions at the Roman Imperial Quarry and Some Unique Samples

    Directory of Open Access Journals (Sweden)

    Tulga Albustanlıoğlu

    2014-01-01

    unsurlarından oluşmaktadır. Ocakların müteahhitler yanında ve onlarla birlikte, doğrudan imparatorluk yönetimince işletilmeye başlanmasıyla, yazıtların biçim ve içeriğinde büyük değişiklikler meydana gelmiştir. Ocakların üretim teknolojisinde, jeolojik şartlardan kaynaklanan bir takım küçük farklılıklar bulunsa da, genelde tüm imparatorluk ocaklarında organizasyonun aynı biçimde şekillendiği imparatorluk yönetimince üretim, denetim ve sevkiyatın bütün mermer ocakları için benzer bir çerçeve içinde düzenlenmiş olduğu anlaşılmaktadır. Abstract The most significant source that sheds light on the history of the quarry activities is, without a doubt, the inscriptions. The information regarding the production date of the stone, the quarry which the stone was produced in, the people who carried out the control operations and the organization and management of the quarries can be obtained through the inscriptions. However such extensive information can be valid if only a well-organized establishment is subjected. Furthermore, while inscriptions are rarely discovered in the quarries, the limited number inscriptions that were attained do not usually include such detailed information, and the content and form can vary due to many different reasons such as weakened government authority, change of ownership and change of management to increase or decrease of production capacity. The tradition of managing imperial quarries trough contractors was abandoned towards the end of the 1st Century and the government control and initiative over production were increased. The information regarding the stone such as the production date, the quarry which stone was produced in, the people who carried out the control operations, the way of organization and management of the quarries can be obtained through the inscriptions. Inscriptions on the tablets can be divided into two groups; inside quarry and outside quarry. A small portion of inside quarry

  20. Characterization of a texture gradient in tantalum plate

    International Nuclear Information System (INIS)

    Wright, S.I.; Gray, G.T. III.

    1994-01-01

    Clark et al. have shown that significant texture gradients can be produced in rolled tantalum plate and that the strength of the gradient is dependent on the processing path. Texture gradients are often ignored because they are time consuming to characterize and add significant complexity to materials modeling. The variation in texture through the thickness of rolled materials is most commonly measured by sectioning samples to different depths through the thickness of the plate and then measuring the texture from these section planes by X-ray diffraction. A new technique based on automatic indexing of electron backscatter diffraction patterns in the scanning electron microscope enables spatially specific orientations to be measured in a practical manner. This technique allows spatial variations in texture to be measured directly enabling gradients in texture to be investigated in more detail than previously possible. This data can be used directly in coupled finite-element/polycrystal-plasticity models to simulate the effects of variations in texture on the plastic behavior of polycrystals. This work examines the variation in texture through the thickness of a tantalum plate and its resultant effect on the compressive deformation of samples prepared from the plate. The characterization of the texture gradient using the automatic point-by-point measurement technique mentioned above is described in detail. The effect of the gradient on the plastic response of through-thickness compression tests is also discussed

  1. Investigating the Effect of Soil Texture and Fertility on Evapotranspiration and Crop Coefficient of Maize Forage

    Directory of Open Access Journals (Sweden)

    M. Ghorbanian Kerdabadi

    2017-02-01

    Full Text Available Introduction: Crop coefficient varies in different environmental conditions, such as deficit irrigation, salinity and intercropping. The effect of soil fertility and texture of crop coefficient and evapotranspiration of maize was investigated in this study. Low soil fertility and food shortages as a stressful environment for plants that makes it different evapotranspiration rates of evapotranspiration calculation is based on the FAO publication 56. Razzaghi et al. (2012 investigate the effect of soil type and soil-drying during the seed-filling phase on N-uptake, yield and water use, a Danish-bred cultivar (CV. Titicaca was grown in field lysimeters with sand, sandy loam and sandy clay loam soil. Zhang et al (2014 were investigated the Effect of adding different amounts of nitrogen during three years (from 2010 to 2012 on water use efficiency and crop evapotranspiration two varieties of winter wheat. The results of their study showed. The results indicated the following: (1 in this dry land farming system, increased N fertilization could raise wheat yield, and the drought-tolerant Changhan No. 58 showed a yield advantage in drought environments with high N fertilizer rates; (2 N application affected water consumption in different soil layers, and promoted wheat absorbing deeper soil water and so increased utilization of soil water; and (3 comprehensive consideration of yield and WUE of wheat indicated that the N rate of 270 kg/ha for Changhan No. 58 was better to avoid the risk of reduced production reduction due to lack of precipitation; however, under conditions of better soil moisture, the N rate of 180 kg/ha was more economic. Materials and Methods: The study was a factorial experiment in a completely randomized design with three soil texture treatment, including silty clay loam, loam and sandy-loam soil and three fertility treatment, including without fertilizer, one and two percent fertilizer( It was conducted at the experimental farm in

  2. Effects of alkali on protein polymerization and textural characteristics of textured wheat protein.

    Science.gov (United States)

    Li, Ting; Guo, Xiao-Na; Zhu, Ke-Xue; Zhou, Hui-Ming

    2018-01-15

    The impact of alkali addition on the degree of gluten polymerization and textural characteristics of textured wheat protein was investigated. Results showed that the extrusion process increased the average molecular weight of gluten as evidenced by SDS-PAGE and SDS extractable protein. The addition of alkali not only promoted the degree of gluten polymerization, but also induced dehydroalanine-derived cross-linking. Alkali addition decreased the content of cystine and increased the contents of dehydroalanine and lanthionine. The obvious decrease of free SH showed that dehydroalanine-derived cross-linking was quantitatively less crucial than disulfide cross-linking. Furthermore, the protein cross-linking induced by alkali improved the texture properties of gluten extrudates. SEM analysis showed extrusion under alkaline condition conferred a more fibrous microstructure as a consequence of a compact gluten network. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Texture and Elastic Anisotropy of Mantle Olivine

    Science.gov (United States)

    Nikitin, A. N.; Ivankina, T. I.; Bourilitchev, D. E.; Klima, K.; Locajicek, T.; Pros, Z.

    Eight olivine rock samples from different European regions were collected for neu- tron texture analyses and for P-wave velocity measurements by means of ultrasonic sounding at various confining pressures. The orientation distribution functions (ODFs) of olivine were determined and pole figures of the main crystallographic planes were calculated. The spatial P-wave velocity distributions were determined at confining pressures from 0.1 to 400 MPa and modelled from the olivine textures. In dependence upon the type of rock (xenolith or dunite) different behavior of both the P-wave veloc- ity distributions and the anisotropy coefficients with various confining pressures was observed. In order to explain the interdependence of elastic anisotropy and hydrostatic pressure, a model for polycrystalline olivine rocks was suggested, which considers the influence of the crystallographic and the mechanical textures on the elastic behaviour of the polycrystal. Since the olivine texture depends upon the active slip systems and the deformation temperature, neutron texture analyses enable us to estimate depth and thermodynamical conditions during texture formation.

  4. A Novel Texture Classification Procedure by using Association Rules

    Directory of Open Access Journals (Sweden)

    L. Jaba Sheela

    2008-11-01

    Full Text Available Texture can be defined as a local statistical pattern of texture primitives in observer’s domain of interest. Texture classification aims to assign texture labels to unknown textures, according to training samples and classification rules. Association rules have been used in various applications during the past decades. Association rules capture both structural and statistical information, and automatically identify the structures that occur most frequently and relationships that have significant discriminative power. So, association rules can be adapted to capture frequently occurring local structures in textures. This paper describes the usage of association rules for texture classification problem. The performed experimental studies show the effectiveness of the association rules. The overall success rate is about 98%.

  5. 2014 NOAA Ortho-rectified Mosaic of Hurricane Sandy Coastal Impact Area

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles at 0.35m GSD created for NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative in Hurricane Sandy coastal...

  6. Textural features for radar image analysis

    Science.gov (United States)

    Shanmugan, K. S.; Narayanan, V.; Frost, V. S.; Stiles, J. A.; Holtzman, J. C.

    1981-01-01

    Texture is seen as an important spatial feature useful for identifying objects or regions of interest in an image. While textural features have been widely used in analyzing a variety of photographic images, they have not been used in processing radar images. A procedure for extracting a set of textural features for characterizing small areas in radar images is presented, and it is shown that these features can be used in classifying segments of radar images corresponding to different geological formations.

  7. Texture analyses of Sauropod dinosaur bones from Tendaguru

    Energy Technology Data Exchange (ETDEWEB)

    Pyzalla, A.R. [TU Wien, Institute of Material Science and Technology, Karlsplatz 13-308, A-1040 Vienna (Austria) and MPI fuer Eisenforschung GmbH, Max-Planck-Str. 1, D-40237 Duesseldorf (Germany)]. E-mail: pyzalla@mpie.de; Sander, P.M. [University of Bonn, Institute of Palaeontology, Nusseallee, D-53115 Bonn (Germany); Hansen, A. [TU Clausthal, Institute of Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processingnd GKSS Research Centre Geesthacht GmbH, Geesthacht, Max-Planck-Str.1, D-21502 Geesthacht (Germany); Ferreyro, R. [TU Wien, Institute of Material Science and Technology, Karlsplatz 13-308, A-1040 Vienna (Austria); Yi, S.-B. [TU Clausthal, Institute of Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processingnd GKSS Research Centre Geesthacht GmbH, Geesthacht, Max-Planck-Str.1, D-21502 Geesthacht (Germany); MPI fuer Eisenforschung GmbH, Max-Planck-Str. 1, D-40237 Duesseldorf (Germany); Stempniewicz, M. [TU Wien, Institute of Material Science and Technology, Karlsplatz 13-308, A-1040 Vienna (Austria); Brokmeier, H.-G. [TU Clausthal, Institute of Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processingnd GKSS Research Centre Geesthacht GmbH, Geesthacht, Max-Planck-Str.1, D-21502 Geesthacht (Germany)

    2006-11-10

    The apatite texture of fossil Brachiosaurus brancai and Barosaurus africanus sauropod bones from the excavation site at Tendaguru, Tanzania, was characterized by neutron diffraction pole figures. The results obtained reveal predominantly <0 0 0 1>-fibre textures of the apatite; the fibre direction coincides with the longitudinal direction of the long bones of the skeletons. Neutron pole figures further indicate that other texture types may also be present. Texture strength is similar to dinosaur tendons and contemporary turkey tendon studied by others. Variations of texture strength across the bone wall cross-sections are not significantly large.

  8. effect of tractor forward speed on sandy loam soil physical ...

    African Journals Online (AJOL)

    Dr Obe

    Ilorin on a sandy loam soil to evaluate the effect of the imposition of different .... of the blade is 10.5cm. ... arranged in an inverted cone shape with ... replicates were taken for each speed run. The ..... Thakur, T. C; A. Yadav; B. P. Varshney and.

  9. Sorption and Migration Mechanisms of 237 Np through Sandy Soil

    International Nuclear Information System (INIS)

    Chantaraprachoom, Nanthavan; Tanaka, Tadao

    2003-06-01

    In order to evaluate migration behavior of radioactive nuclides in the disposal of low-level radioactive waste into a shallow land burial, the sorption characteristic and migration behavior of 237 Np through sandy soil was studied. Two experimental methods were performed by using batch and column systems. The distribution coefficients (K d ) obtained from the adsorption and desorption process are rather small about 16 and 21 cm 3 /g respectively. Size distribution of 237 Np species in the influent solution was measured by ultra-filtration technique. Migration mechanism of 237 Np was studied by column experiments. The experimental condition was the influence of volume of eluting solution; 100, 300, 500, 1000 and 2000 ml respectively. The result from five column experiments confirm that the sorption characteristics of 237 Np are mainly controlled by a reversible ion-exchange reaction and the migration of 237 Np in the sandy soil can be estimated by using the K d concept

  10. Rapidly 3D Texture Reconstruction Based on Oblique Photography

    Directory of Open Access Journals (Sweden)

    ZHANG Chunsen

    2015-07-01

    Full Text Available This paper proposes a city texture fast reconstruction method based on aerial tilt image for reconstruction of three-dimensional city model. Based on the photogrammetry and computer vision theory and using the city building digital surface model obtained by prior treatment, through collinear equation calculation geometric projection of object and image space, to obtain the three-dimensional information and texture information of the structure and through certain the optimal algorithm selecting the optimal texture on the surface of the object, realize automatic extraction of the building side texture and occlusion handling of the dense building texture. The real image texture reconstruction results show that: the method to the 3D city model texture reconstruction has the characteristics of high degree of automation, vivid effect and low cost and provides a means of effective implementation for rapid and widespread real texture rapid reconstruction of city 3D model.

  11. Global crystallographic textures obtained by neutron and synchrotron radiation

    International Nuclear Information System (INIS)

    Brokmeier, Heinz-Guenter

    2006-01-01

    Global crystallographic textures belong to the main characteristic parameters of engineering materials. The global crystallographic texture is always the average texture of a well-defined sample volume which is representative to solve practical engineering problems. Thus a beam having a high penetration power is needed available as neutron or high energetic X-ray radiation. Texture type and texture sharpness are of great importance for materials properties such as the deep drawing behaviour, one of the basic techniques in many industries. Advantages and disadvantages of both radiations make them complementary for measuring crystallographic textures in a wide range of materials

  12. 2012 USGS EAARL-B Coastal Topography: Post-Sandy, First Surface (NJ)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — ASCII xyz and binary point-cloud data, as well as a digital elevation model (DEM) of a portion of the New Jersey coastline, pre- and post-Hurricane Sandy (October...

  13. Texture analysis using angle dispersive neutron nuclear scattering

    International Nuclear Information System (INIS)

    Brokmeier, H.G.

    1995-01-01

    This paper describes in detail the method of texture determination using neutron diffraction. The main advantages of neutron diffraction arise from the high penetration depth for most materials which is a factor of 10 2 -10 4 higher than for X-ray diffraction. Consequently neutron diffraction is an efficient tool for the investigation of global textures and coarse grained materials. Moreover, the measurement of large sample volumes gives excellent grain statistics, allows the influence of texture inhomogeneities to be neglected and allows the measurement of complete pole figures even of minority phases. A number of examples show the application of neutron diffraction to measure textures of metals, alloys, composites, intermetallic compounds and rocks. A detailed description of TEX-2 the neutron texture diffractometer at GKSS Research Centre is given which is completed by a comparison to other neutron texture diffractometers. (orig.) [de

  14. Fine organic particles in a sandy beach system (Puck Bay, Baltic Sea

    Directory of Open Access Journals (Sweden)

    Lech Kotwicki

    2005-06-01

    Full Text Available A total of over 550 samples of particulate organic matter (POM were obtained from swash and groundwater samples taken on a monthly basis from seven localities on the sandy shores of Puck Bay in 2002 and 2003. Sandy sediment cores from the swash zone were collected to assess the amount of POM in the pore waters. The mean annual concentrations of POM varied between localities from 20 to 500 mg in groundwater and from 6 to 200 mg dm-3 in swash water. The carbon/nitrogen (C/N ratio in suspended matter was always higher in groundwater (annual mean 12 than in swash water (annual mean 7. The C/N ratio indicates a local, algal origin of POM in the shallow coastal zone.

  15. TEXTURE ANALYSIS OF SPELT WHEAT BREAD

    Directory of Open Access Journals (Sweden)

    Magdaléna Lacko - Bartošová

    2013-02-01

    Full Text Available The bread quality is considerably dependent on the texture characteristic of bread crumb. Texture analysis is primarily concerned with the evaluation of mechanical characteristics where a material is subjected to a controlled force from which a deformation curve of its response is generated. It is an objective physical examination of baked products and gives direct information on the product quality, oppositely to dough rheology tests what are inform on the baking suitability of the flour, as raw material. This is why the texture analysis is one of the most helpful analytical methods of the product development. In the framework of our research during the years 2008 – 2009 were analyzed selected indicators of bread crumb for texture quality of three Triticum spelta L. cultivars – Oberkulmer Rotkorn, Rubiota and Franckenkorn grown in an ecological system at the locality of Dolna Malanta near Nitra. The bread texture quality was evaluated on texture analyzer TA.XT Plus and expressed as crumb firmness (N, stiffness (N.mm-1 and relative elasticity (%.Our research proved that all selected indicators were significantly influenced by the year of growing and variety. The most soft bread was measured in Rubiota, whereas bread crumb samples from Franckenkorn were the most firm and stiff. Relative elasticity confirmed that the lowest firmness and stiffness was found in Rubiota bread. The spelt grain can be a good source for making bread flour, but is closely dependent on choice of spelt variety.

  16. Validation of regression models for nitrate concentrations in the upper groundwater in sandy soils

    International Nuclear Information System (INIS)

    Sonneveld, M.P.W.; Brus, D.J.; Roelsma, J.

    2010-01-01

    For Dutch sandy regions, linear regression models have been developed that predict nitrate concentrations in the upper groundwater on the basis of residual nitrate contents in the soil in autumn. The objective of our study was to validate these regression models for one particular sandy region dominated by dairy farming. No data from this area were used for calibrating the regression models. The model was validated by additional probability sampling. This sample was used to estimate errors in 1) the predicted areal fractions where the EU standard of 50 mg l -1 is exceeded for farms with low N surpluses (ALT) and farms with higher N surpluses (REF); 2) predicted cumulative frequency distributions of nitrate concentration for both groups of farms. Both the errors in the predicted areal fractions as well as the errors in the predicted cumulative frequency distributions indicate that the regression models are invalid for the sandy soils of this study area. - This study indicates that linear regression models that predict nitrate concentrations in the upper groundwater using residual soil N contents should be applied with care.

  17. Some distinguishing characteristics of contour and texture phenomena in images

    Science.gov (United States)

    Jobson, Daniel J.

    1992-01-01

    The development of generalized contour/texture discrimination techniques is a central element necessary for machine vision recognition and interpretation of arbitrary images. Here, the visual perception of texture, selected studies of texture analysis in machine vision, and diverse small samples of contour and texture are all used to provide insights into the fundamental characteristics of contour and texture. From these, an experimental discrimination scheme is developed and tested on a battery of natural images. The visual perception of texture defined fine texture as a subclass which is interpreted as shading and is distinct from coarse figural similarity textures. Also, perception defined the smallest scale for contour/texture discrimination as eight to nine visual acuity units. Three contour/texture discrimination parameters were found to be moderately successful for this scale discrimination: (1) lightness change in a blurred version of the image, (2) change in lightness change in the original image, and (3) percent change in edge counts relative to local maximum.

  18. AUTOMATIC TEXTURE RECONSTRUCTION OF 3D CITY MODEL FROM OBLIQUE IMAGES

    Directory of Open Access Journals (Sweden)

    J. Kang

    2016-06-01

    Full Text Available In recent years, the photorealistic 3D city models are increasingly important in various geospatial applications related to virtual city tourism, 3D GIS, urban planning, real-estate management. Besides the acquisition of high-precision 3D geometric data, texture reconstruction is also a crucial step for generating high-quality and visually realistic 3D models. However, most of the texture reconstruction approaches are probably leading to texture fragmentation and memory inefficiency. In this paper, we introduce an automatic framework of texture reconstruction to generate textures from oblique images for photorealistic visualization. Our approach include three major steps as follows: mesh parameterization, texture atlas generation and texture blending. Firstly, mesh parameterization procedure referring to mesh segmentation and mesh unfolding is performed to reduce geometric distortion in the process of mapping 2D texture to 3D model. Secondly, in the texture atlas generation step, the texture of each segmented region in texture domain is reconstructed from all visible images with exterior orientation and interior orientation parameters. Thirdly, to avoid color discontinuities at boundaries between texture regions, the final texture map is generated by blending texture maps from several corresponding images. We evaluated our texture reconstruction framework on a dataset of a city. The resulting mesh model can get textured by created texture without resampling. Experiment results show that our method can effectively mitigate the occurrence of texture fragmentation. It is demonstrated that the proposed framework is effective and useful for automatic texture reconstruction of 3D city model.

  19. The Sandy Hook Elementary School shooting as tipping point

    Science.gov (United States)

    Shultz, James M; Muschert, Glenn W; Dingwall, Alison; Cohen, Alyssa M

    2013-01-01

    Among rampage shooting massacres, the Sandy Hook Elementary School shooting on December 14, 2012 galvanized public attention. In this Commentary we examine the features of this episode of gun violence that has sparked strong reactions and energized discourse that may ultimately lead toward constructive solutions to diminish high rates of firearm deaths and injuries in the United States. PMID:28228989

  20. A study on the aseismic safety of the experimental VHTR on the dense sandy layer

    International Nuclear Information System (INIS)

    Fujita, Shigeki; Ito, Yoshio; Baba, Osamu; Suzuki, Hideyuki; Takewaki, Naonobu; Kondo, Tsukasa; Yoshimura, Takashi; Yamada, Hitoshi.

    1986-12-01

    A series of studies has been carried out in 1983 and 1985 for the purpose of confirming the aseismic safety of the Experimental VHTR on the dense sandy layer. In 1983, effect of some of soil properties on seismic responses of the reactor building was estimated by means of parametric survey, and soil properties were estimated by analyzing the obserbed earthquake record. In 1985, literature review, linear, nonlinear parametric analyses and nonlinear simulation analyses were carried to study and compare the analysis method. In addition, seismic response of proposed construction site was estimated with nonlinear analysis method. As a result of these studies, the seismic response of reactor building on the dense sandy layers and wave propagation characteristics of sandy layers are understood. Especially, by means of many parametric studies, the effect of input wave characteristics, soil stiffness, nonlinear characteristics of soil properties and nonlinear analysis method on the reactor building responses were evaluated. (author)