Atomic Fisher information versus atomic number

International Nuclear Information System (INIS)

Nagy, A.; Sen, K.D.

2006-01-01

It is shown that the Thomas-Fermi Fisher information is negative. A slightly more sophisticated model proposed by Gaspar provides a qualitatively correct expression for the Fisher information: Gaspar's Fisher information is proportional to the two-third power of the atomic number. Accurate numerical calculations show an almost linear dependence on the atomic number

Sand transportation and reverse patterns over leeward face of sand dune

Science.gov (United States)

Jiang, Hong; Dun, Hongchao; Tong, Ding; Huang, Ning

2017-04-01

Sand saltation has complex interactions with turbulent flow and dune form. Most models of wind-blown sand consider ideal circumstances such as steady wind velocity and a flat surface, and the bulk of data on wind flow and sand transport over an individual dune has focused mostly on the influence of dune shape or inter-dune space on the wind flow, neglecting the effect of morphology on sand saltation, particularly airflow and sand transportation over the leeward slope. Wind flow structures over the leeward slope of sand dunes have a fundamental influence on the organization of sand dunes. In order to understand sand dune dynamics, lee face airflow and sediment transportation should be paid more attention. Previous field observations could not measure turbulent flow structure well because of the limited observation points and the influence of experiment structure on wind field. In addition, the reverse sand particles over leeward face could not be collected by sand trap in field. Numerous field observations could not measure turbulent flow structure because of the limited observation points and the influence of experimental structures on the wind field. In addition, the reverse transport of sand particles over leeward face could not be collected by sand traps in field. Therefore, this paper aims to investigate the turbulent flow structure and sand transport pattern over the leeward slope. A numerical model of sand saltation over slope terrain is constructed, which also considers the coupling effects between air flow and sand particles. The large eddy simulation method is used to model turbulent flow. Sand transport is simulated by tracking the trajectory of each sand particle. The results show that terrain significantly alters the turbulent air flow structure and wind-blown sand movement, especially over the leeward slope. Here, mass flux increases initially and then decreases with height in the reversed flow region in the direction of wind flow, and the mass flux

Oil sands supply outlook

International Nuclear Information System (INIS)

Dunbar, R.

2004-01-01

In March 2004, The Canadian Energy Research Institute released a report on the expected future supply from Alberta's oil sands. The report indicates that the future for the already well-established oil sands industry is promising, particularly given the outlook for oil prices. The challenges facing the industry include higher industry supply costs and the need for innovative commercial and technological solutions to address the risks of irregularities and changes in crude oil prices. In 2003, the industry produced 874 thousand barrels per day of synthetic crude oil and unprocessed crude bitumen. This represents 35 per cent of Canada's total oil production. Current production capacity has increased to 1.0 million barrels per day (mbpd) due to new projects. This number may increase to 3.5 mbpd by 2017. Some new projects may be deferred due to the higher raw bitumen and synthetic crude oil supply costs. This presentation provided supply costs for a range of oil sands recovery technologies and production projections under various business scenarios. tabs., figs

The phlebotomine sand flies fauna in Parque Estadual do Rio Doce, Minas Gerais, Brazil.

Science.gov (United States)

de Souza, Cristian Ferreira; Brazil, Reginaldo Peçanha; Bevilacqua, Paula Dias; Andrade Filho, Jose Dilermando

2015-12-02

Phlebotomine sand flies are dipterans of the family Psychodidae. They are very important to veterinary medicine because some species are vectors of infective forms of Leishmania spp., the etiological agents of leishmaniasis. The Parque Estadual do Rio Doce is located in an area with constant reports of cases of leishmaniasis. In order to better understanding the phlebotamine sand fly fauna of the park, the present work was undertaken with the goal of analyzing phlebotomine sand flies collected there, verifying their seasonality and correlating their presence with forest and/or anthropic areas. To analyze the fauna of phlebotomine sand flies, HP-type, model CDC light traps were distributed along the Juquita trail of PERD. Twelve traps were installed between September 2012 and February 2014, and captured specimens were identified to species. A total of 1993 phlebotomine sand flies of 30 species were captured. The most abundant species were Pressatia choti, Psychodopygus davisi and Nyssomyia intermedia. The high number of Nyssomyia intermedia captured drew attention because they are considered one of the vectors of the infective Leishmania braziliensis present at PERD. No seasonality was observed in the occurrence of phlebotomine sand flies captured at PERD. The number of captured specimens of vector species, and the distance of traps from the forest boarder, were negatively correlated, showing that these vectors (Nyssomyia intermedia, Nyssomyia whitmani and Migonemyia migonei) were less common inside the forest area and that attention should be drawn to other potential vector species in the forest. These results can contribute to leishmaniasis prevention strategies directed at the visitors and professionals at or near PERD. The finding of the presence of Leishmania vectors in the park area must be given attention, since disease transmission can threaten people who visit PERD and its surroundings. Therefore, information on the prevention of leishmaniasis needs to be

Log-inject-log in sand consolidation

International Nuclear Information System (INIS)

Murphy, R.P.; Spurlock, J.W.

1977-01-01

A method is described for gathering information for the determination of the adequacy of placement of sand consolidating plastic for sand control in oil and gas wells. The method uses a high neutron cross-section tracer which becomes part of the plastic and uses pulsed neutron logging before and after injection of the plastic. Preferably, the method uses lithium, boron, indium, and/or cadmium tracers. Boron oxide is especially useful and can be dissolved in alcohol and mixed with the plastic ingredients

Sea Bed Sand Waves Studied To Help Pipeline Planners

NARCIS (Netherlands)

van der Mark, C.F.; de Koning, M.F.; Blom, Astrid; Hulscher, Suzanne J.M.H.; Stolk, A.

2008-01-01

The article cites a study that offers information on the variability of sand wave characteristics in the North Sea. The sand waves variability includes a statement that pipelines may start vibrating due to turbulence generated under the free span and navigational channels often need to be dredged

Reclaimability of the spent sand mixture – sand with bentonite – sand with furfuryl resin

Directory of Open Access Journals (Sweden)

J. Dańko

2011-04-01

Full Text Available Introduction of new binding materials and new technologies of their hardening in casting moulds and cores production requires theapplication of reclamation methods adequate to their properties as well as special devices realizing tasks. The spent sands circulationsystem containing the same kind of moulding and core sands is optimal from the point of view of the expected reclamation results.However, in the face of a significant variability of applied technologies and related to them various reclamation methods, the need - of theobtained reclamation products assessment on the grounds of systematic criteria and uniform bases – arises, with a tendency of indicatingwhich criteria are the most important for the given sand system. The reclaimability results of the mixture of the spent moulding sand withGeko S bentonite and the spent core sand with the Kaltharz 404U resin hardened by acidic hardener 100 T3, are presented in the paper.Investigations were performed with regard to the estimation of an influence of core sands additions (10 –25% on the reclaimed materialquality. Dusts and clay content in the reclaim, its chemical reaction (pH and ignition loss were estimated. The verification of the reclaiminstrumental assessment was performed on the basis of the technological properties estimation of moulding sand with bentonite, where the reclaimed material was used as a matrix.

Invasive plants on disturbed Korean sand dunes

Science.gov (United States)

Kim, Kee Dae

2005-01-01

The sand dunes in coastal regions of South Korea are important ecosystems because of their small size, the rare species found in this habitat, and the beautiful landscapes they create. This study investigated the current vegetative status of sand dunes on three representative coasts of the Korean peninsula, and on the coasts of Cheju Island, and assessed the conditions caused by invasive plants. The relationships between the degree of invasion and 14 environmental variables were studied. Plots of sand dunes along line transects perpendicular to the coastal lines were established to estimate vegetative species coverage. TWINSPAN (Two-Way Indicator Species Analysis), CCA (Canonical Correspondence Analysis), and DCCA (Detrended Canonical Correspondence Analysis) were performed to classify communities on sand dunes and assess species composition variation. Carex kobomugi, Elymus mollis, and Vitex rotundifolia were found to be the dominant species plotted on the east, the west, and the peripheral coasts of Cheju Island, respectively. Vegetation on the south coast was totally extinct. The 19 communities, including representative C. kobomugi, C. kobomugi- Ixeris repens, C. kobomugi- Oenothera biennis, E. mollis, Lolium multiflorum- Calystegia soldanella, and V. rotundifolia- C. kobomugi, were all classified according to TWINSPAN. Oenothera biennis and L. multiflorum were exotics observed within these native communities. CCA showed that invasive native and exotic species distribution was segregated significantly, according to disturbance level, exotic species number, gravel, sand and silt contents, as well as vegetation size. It further revealed that human disturbance can strongly favor the settlement of invasive and exotic species. Restoration options to reduce exotic plants in the South Korean sand dune areas were found to be the introduction of native plant species from one sand dune into other sand dune areas, prohibition of building and the introduction of exotic

A Improved Seabed Surface Sand Sampling Device

Science.gov (United States)

Luo, X.

2017-12-01

In marine geology research it is necessary to obtain a suf fcient quantity of seabed surface samples, while also en- suring that the samples are in their original state. Currently,there are a number of seabed surface sampling devices available, but we fnd it is very diffcult to obtain sand samples using these devices, particularly when dealing with fne sand. Machine-controlled seabed surface sampling devices are also available, but generally unable to dive into deeper regions of water. To obtain larger quantities of seabed surface sand samples in their original states, many researchers have tried to improve upon sampling devices,but these efforts have generally produced ambiguous results, in our opinion.To resolve this issue, we have designed an improved andhighly effective seabed surface sand sampling device that incorporates the strengths of a variety of sampling devices. It is capable of diving into deepwater to obtain fne sand samples and is also suited for use in streams, rivers, lakes and seas with varying levels of depth (up to 100 m). This device can be used for geological mapping, underwater prospecting, geological engineering and ecological, environmental studies in both marine and terrestrial waters.

Effects of Moisture Content on the Foundry Properties of Yola Natural Sand

Directory of Open Access Journals (Sweden)

Paul Aondona IHOM

2012-08-01

Full Text Available The effect of moisture content of Yola natural sand has been studied. The moisture content was varied from 1 to 9%. The effect of the moisture content on the green compression strength, green permeability and bulk density was investigated. Particle size distribution of the natural sand, the grain fineness number, average grain size, grain shape and the clay content of the natural sand were also studied. 5% moisture gave the optimum green compression strength of 118.6KN/m2. The dry compression strength increased with moisture content, an optimum value of 4000KN/m2 was obtained at 9% moisture. The Yola natural sand had a grain fineness number of 88.05AFS, average grain size of 335.78 microns and a clay content of 26%. A sand mixture containing 5% moisture was prepared and used to produce a test casting with aluminium scraps, the test casting was sound.

Eastern Scheldt Sand, Baskarp Sand No. 15

DEFF Research Database (Denmark)

Andersen, A. T; Madsen, E. B.; Schaarup-Jensen, A. L.

The present data report contains data from 13 drained triaxial tests, performed on two different sand types in the Soil Mechanics Laboratory at Aalborg University in March, 1997. Two tests have been performed on Baskarp Sand No. 15, which has already ken extensively tested in the Soil Mechanics...... Laboratory. The remaining 11 triaxial tests have ben performed on Eastern Scheldt Sand, which is a material not yet investigated at the Soil Mechanics Laboratory. In the first pari of this data report, the characteristics of the two sand types in question will be presented. Next, a description...... will described. In this connection, the procedure for preparation of the soil specimens will be presented, and the actual performance of the tests will be briefly outlined. Finally, the procedure for processing of the measurements from the laboratory in order to obtain usable data will be described. The final...

Estimation of daily albedo on Tottori sand surface

International Nuclear Information System (INIS)

Gu, S.; Otsuki, K.; Kamichika, M.

2001-01-01

Daily albedos of a bare sand surface were measured with a solarimeter (Eko MS-62) between 23 August and 30 November in 1997 at Tottori sand dune, Japan. These quickly decreased on rainy days, and recovered during dry spells (days between rainfalls). A strong exponential relationship was found between daily albedos and the number of dry days. The daily albedos on dry days also showed a direct relationship with daily transmissivities in the range less than 0.55. Two simple models were developed to estimate daily albedos for dry spell days on bare Tottori sand surface using routine meteorological data. Daily albedos were calculated using these two models, and compared with the measured daily albedos. For Model #1, the daily albedos were successfully predicted only using the number of dry spell days; the correlation coefficient between the estimated and measured albedo was 0.73, and the standard error was 1.2%. For Model #2, the number of dry spell days and transmissivity were considered in order to calculate the daily albedo on dry spell days; the correlation coefficient was 0.85, and the standard error was 0.9%. Estimated albedos were in good agreement with measured albedos. (author)

The paratransgenic sand fly: a platform for control of Leishmania transmission.

Science.gov (United States)

Hurwitz, Ivy; Hillesland, Heidi; Fieck, Annabeth; Das, Pradeep; Durvasula, Ravi

2011-05-19

Leishmania donovani is transmitted by the bite of the sand fly, Phlebotomus argentipes. This parasite is the agent of visceral leishmaniasis (VL), an endemic disease in Bihar, India, where prevention has relied mainly on DDT spraying. Pesticide resistance in sand fly populations, environmental toxicity, and limited resources confound this approach. A novel paratransgenic strategy aimed at control of vectorial transmission of L. donovani is presented using Bacillus subtilis, a commensal bacterium isolated from the sand fly gut. In this work, B. subtilis expressing Green Fluorescent Protein (GFP) was added to sterilized larval chow. Control pots contained larval chow spiked either with untransformed B. subtilis or phosphate-buffered saline. Fourth-instar P. argentipes larvae were transferred into the media and allowed to mature. The number of bacterial colony forming units, relative abundance and the mean microbial load were determined per developmental stage. Addition of B. subtilis to larval chow did not affect sand fly emergence rates. B. cereus and Lys fusiformis were identified at each developmental stage, revealing transstadial passage of endogenous microbes. Larvae exposed to an exogenous bolus of B. subtilis harbored significantly larger numbers of bacteria. Bacterial load decreased to a range comparable to sand flies from control pots, suggesting an upper limit to the number of bacteria harbored. Emerging flies reared in larval chow containing transformed B. subtilis carried large numbers of these bacteria in their gut lumens. Strong GFP expression was detected in these paratransgenic flies with no spread of transformed bacteria to other compartments of the insects. This is the first demonstration of paratransgenic manipulation of P. argentipes. Paratransgenic manipulation of P. argentipes appears feasible. Expression of leishmanicidal molecules via commensal bacteria commonly found at breeding sites of P. argentipes could render adult sand flies refractory

Oil sands economic impacts Canada : CERI report : backgrounder

International Nuclear Information System (INIS)

2005-09-01

Oil sands production now accounts for 1 out of every 2 barrels of supply in Western Canada. It is anticipated that Alberta's oil sands sector will experience significant growth over the next few decades. This paper provided an outline of the challenges and economic impacts resulting from oil sands development in Canada. Alberta's oil sands reserves are estimated at 175 billion barrels that are deemed economically recoverable using current technology. At current production levels, reserves will sustain production of 2.5 million barrels per day for the next 200 years. A study by the Canadian Energy Research Institute (CERI) has forecast $100 billion in investment for the 2000-2020 period. Numerous companies hold leases and are planning new projects. A number of recent advances in oil sands technology are expected to further reduce costs as development matures. A royalty and tax regime that provides long-term fiscal certainty is a key factor that supports current oil sands growth forecasts. The CERI study has indicated that economic spinoffs from oil sands development relate to employment generated outside of Alberta, and that the largest percentage of government revenue accrues to the federal government. However, development may be constrained because the pace of growth in the sector may exceed underlying infrastructure related to roads, housing and municipal services. An adequate workforce of qualified trades and technical and professional people is also crucial. Several pipeline projects have been proposed to deliver oil sands crudes to new markets over the next decade. It was concluded that the billions of dollars invested in oil sands in Alberta will contribute to the economic prosperity of the entire country. 11 figs

Microbiological and mycological beach sand quality in a volcanic environment: Madeira archipelago, Portugal.

Science.gov (United States)

Pereira, Elisabete; Figueira, Celso; Aguiar, Nuno; Vasconcelos, Rita; Vasconcelos, Sílvia; Calado, Graça; Brandão, João; Prada, Susana

2013-09-01

Madeira forms a mid-Atlantic volcanic archipelago, whose economy is largely dependent on tourism. There, one can encounter different types of sand beach: natural basaltic, natural calcareous and artificial calcareous. Microbiological and mycological quality of the sand was analyzed in two different years. Bacterial indicators were detected in higher number in 2010 (36.7% of the samples) than in 2011 (9.1%). Mycological indicators were detected in a similar percentage of samples in 2010 (68.3%) and 2011 (75%), even though the total number of colonies detected in 2010 was much higher (827 in 41 samples) than in 2011 (427 in 66 samples). Enterococci and potentially pathogenic and allergenic fungi (particularly Penicillium sp.) were the most common indicators detected in both years. Candida sp. yeast was also commonly detected in the samples. The analysis of the 3rd quartile and maximum numbers of all indicators in samples showed that artificial beaches tend to be more contaminated than the natural ones. However, a significant difference between the variables was lacking. More monitoring data (number of bathers, sea birds, radiation intensity variation, and a greater number of samples) should be collected in order to confirm if these differences are significant. In general, the sand quality in the archipelago's beaches was good. As the sand may be a vector of diseases, an international common set of indicators and values and a compatible methodologies for assessing sand contamination, should be defined, in order to provide the bather's with an indication of beach sand quality, rather than only the water. Copyright © 2013 Elsevier B.V. All rights reserved.

Insecticide Treated Camouflage Sceening Reduces Sand Fly Numbers in Leishmania-Endemic Regions in Kenya

Science.gov (United States)

Current U.S. military operations in deserts face persistent threats from sand flies that transmit human Leishmania. In this study we investigated the efficacy of artificial barriers treated with residual insecticide to potentially reduce the risk of human infection from leishmaniasis by reducing the...

Combining epidemiology with basic biology of sand flies, parasites, and hosts to inform leishmaniasis transmission dynamics and control.

Science.gov (United States)

Courtenay, Orin; Peters, Nathan C; Rogers, Matthew E; Bern, Caryn

2017-10-01

Quantitation of the nonlinear heterogeneities in Leishmania parasites, sand fly vectors, and mammalian host relationships provides insights to better understand leishmanial transmission epidemiology towards improving its control. The parasite manipulates the sand fly via production of promastigote secretory gel (PSG), leading to the "blocked sand fly" phenotype, persistent feeding attempts, and feeding on multiple hosts. PSG is injected into the mammalian host with the parasite and promotes the establishment of infection. Animal models demonstrate that sand flies with the highest parasite loads and percent metacyclic promastigotes transmit more parasites with greater frequency, resulting in higher load infections that are more likely to be both symptomatic and efficient reservoirs. The existence of mammalian and sand fly "super-spreaders" provides a biological basis for the spatial and temporal clustering of clinical leishmanial disease. Sand fly blood-feeding behavior will determine the efficacies of indoor residual spraying, topical insecticides, and bed nets. Interventions need to have sufficient coverage to include transmission hot spots, especially in the absence of field tools to assess infectiousness. Interventions that reduce sand fly densities in the absence of elimination could have negative consequences, for example, by interfering with partial immunity conferred by exposure to sand fly saliva. A deeper understanding of both sand fly and host biology and behavior is essential to ensuring effectiveness of vector interventions.

Controls on the abruptness of gravel-sand transitions

Science.gov (United States)

Venditti, J. G.; Church, M. A.; Lamb, M. P.; Domarad, N.; Rennie, C. D.

2014-12-01

As gravel-bedded rivers fine downstream, they characteristically exhibit an abrupt transition from gravel- to sand-bed. This is the only abrupt transition in grain-size that occurs in the fluvial system and has attracted considerable attention. A number of competing theories have been proposed to account for the abruptness of the transition, including base-level control, attrition of ~10mm gravel to produce sand, and sediment sorting processes. The prevailing theory for the emergence of abrupt transitions is size selective sorting of bimodal sediment wherein gravel deposits due to downstream declining shear stress, fining the bedload until a sand-bed emerges. We explored this hypothesis by examining grain-size, shear stress, gravel mobility and sand suspension thresholds through the gravel-sand transition (GST) of the Fraser River, British Columbia. The Fraser GST is an arrested gravel wedge with patches of gravel downstream of the wedge forming a diffuse extension. There is an abrupt change in bed slope through the transition that leads to an abrupt change in shear stress. The GST, bed-slope change and backwater caused by the ocean are all coincident spatially, which enhances the sharpness of the GST. Interestingly, the bimodal reach of the river occurs downstream of the GST and exhibits no downstream gradients in shear stress, suspended sediment flux, gravel mobility or sand suspension thresholds. This calls into question the prevailing theory for the emergence of an abrupt GST by size selective sorting. We provide evidence, both empirical and theoretical, that suggests the emergence of an abrupt GST is caused by rapid deposition of sand when fine gravel deposits. We argue that the emergence of gravel-sand transitions is a consequence of gravel-bedded rivers adopting a steeper slope than sand-bedded rivers. The abruptness arises because the bed slope required to convey the gravel load fixes the distal location of a terminal gravel wedge, and once the river has

Diversity of the bacterial and fungal microflora from the midgut and cuticle of phlebotomine sand flies collected in North-Western Iran.

Directory of Open Access Journals (Sweden)

Mohammad Akhoundi

Full Text Available BACKGROUND: Phlebotomine sand flies are the vectors of the leishmaniases, parasitic diseases caused by Leishmania spp. Little is known about the prevalence and diversity of sand fly microflora colonizing the midgut or the cuticle. Particularly, there is little information on the fungal diversity. This information is important for development of vector control strategies. METHODOLOGY/PRINCIPAL FINDINGS: FIVE SAND FLY SPECIES: Phlebotomus papatasi, P. sergenti, P. kandelakii, P. perfiliewi and P. halepensis were caught in Bileh Savar and Kaleybar in North-Western Iran that are located in endemic foci of visceral leishmaniasis. A total of 35 specimens were processed. Bacterial and fungal strains were identified by routine microbiological methods. We characterized 39 fungal isolates from the cuticle and/or the midgut. They belong to six different genera including Penicillium (17 isolates, Aspergillus (14, Acremonium (5, Fusarium (1, Geotrichum (1 and Candida (1. We identified 33 Gram-negative bacteria: Serratia marcescens (9 isolates, Enterobacter cloacae (6, Pseudomonas fluorescens (6, Klebsiella ozaenae (4, Acinetobacter sp. (3, Escherichia coli (3, Asaia sp. (1 and Pantoea sp. (1 as well as Gram-positive bacteria Bacillus subtilis (5 and Micrococcus luteus (5 in 10 isolates. CONCLUSION/SIGNIFICANCE: Our study provides new data on the microbiotic diversity of field-collected sand flies and for the first time, evidence of the presence of Asaia sp. in sand flies. We have also found a link between physiological stages (unfed, fresh fed, semi gravid and gravid of sand flies and number of bacteria that they carry. Interestingly Pantoea sp. and Klebsiella ozaenae have been isolated in Old World sand fly species. The presence of latter species on sand fly cuticle and in the female midgut suggests a role for this arthropod in dissemination of these pathogenic bacteria in endemic areas. Further experiments are required to clearly delineate the vectorial

Fontainebleau Sand

DEFF Research Database (Denmark)

Leth, Caspar Thrane

2006-01-01

The report is a summary of results from laboratory tests in the geotechncial research group on Fontainebleau sand.......The report is a summary of results from laboratory tests in the geotechncial research group on Fontainebleau sand....

Applications of sand control technology in thermal recovery systems

Energy Technology Data Exchange (ETDEWEB)

Rensvold, R F

1982-01-01

The ever-increasing application of thermal methods to recover low gravity crude oil has warranted the review of existing sand control techniques relative to their compatibility with high temperature environments. The advantages and limitations of a large number of materials are considered. Carrying fluids, granular pack solids, clay stabilizers, and resin-coated pack sands are discussed. Resins used for in situ sand consolidation processes also are reviewed, and their suitability for application in a high temperature steam environment is evaluated. The effects of highly deviated boreholes on the placement of pressure packs also are considered. Full scale gravel pack model studies have provided valuable clues to the procedures and materials that help to create optimum pressure packs. 58 references.

Geophysical applications for oil sand mine tailings management

Energy Technology Data Exchange (ETDEWEB)

Parker, D.; Bauman, P. [WorleyParsons, Calgary, AB (Canada)

2009-07-01

Geophysical techniques are applied throughout a mine's life cycle to facilitate siting, constructing and monitoring of tailings dumps and ponds. This presentation described 3 case studies from the Athabasca region in northeast Alberta that demonstrated some of the concerns associated with oil sand mine tailings, and the information that geophysical surveys can provide. The objectives of these studies were to determine the lateral and depth extents of elevated conductivities of soil and groundwater that have high salt concentration from the tailings sand pore fluid. Due to high chloride concentrations within the tailings material, salt within the root zone may affect vegetation. A terrain conductivity survey was designed to map the lateral extents of salinity impact, while an electrical resistivity tomography (ERT) survey was used to delineate the tailings sand leachate at depth. The proper management of oil sand tailings facilities is vital to the life cycle of a mine. It was concluded that geophysical techniques can be instrumental in managing several engineering and environmental challenges, from Pleistocene channel mapping, to tailings pond settling characteristics, to reclaiming tailings sands. 1 ref., 7 figs.

Assessment Method of Overheating Degree of a Spent Moulding Sand with Organic Binder, After the Casting Process

Directory of Open Access Journals (Sweden)

Dańko R.

2013-06-01

Full Text Available A proper management of sand grains of moulding sands requires knowing basic properties of the spent matrix after casting knocking out. This information is essential from the point of view of the proper performing the matrix recycling process and preparing moulding sands with reclaimed materials. The most important parameter informing on the matrix quality - in case of moulding sands with organic binders after casting knocking out - is their ignition loss. The methodology of estimating ignition loss of spent moulding sands with organic binder - after casting knocking out - developed in AGH, is presented in the paper. This method applies the simulation MAGMA software, allowing to determine this moulding sand parameter already at the stage of the production preparation.

New generation expandable sand screens

OpenAIRE

Syltøy, Christer

2014-01-01

Master's thesis in Petroleum engineering This thesis aims to give a general insight into sand control and various sorts of sand control measures and applications of sand control tools. Special focus will be given to expandable sand screens – a technology which came about in the late 1990’s through the use of flexible, expandable tubulars as base pipe in sand screens. More specifically Darcy’s Hydraulic Endurance Screens, a compliant sand screen system using hydraulic activation, and the fu...

Review of four major environmental effects monitoring programs in the oil sands region

International Nuclear Information System (INIS)

Lott, E.O.; Jones, R.K.

2010-10-01

The lack of knowledge on current environmental effects monitoring programs for the mineable oil sands region generates a low public confidence in environment health monitoring and reporting programs for the oil sands operations. In 2010, the Oil Sands Research and Information Network (OSRIN) supervised a study reviewing the major environmental effects monitoring programs that are underway in the Regional Municipality of Wood Buffalo. Four main environmental effects monitoring and reporting organizations existing in the oil sands area were engaged to describe their programs through this study: Alberta Biodiversity Monitoring Institute (ABMI), Cumulative Environmental Management Association (CEMA), Regional Aquatic Monitoring Program (RAMP), Wood Buffalo Environmental Association (WBEA). These different organizations have specific roles in providing information, data and understanding of ecosystem effects. A one page visual summary of environmental effects monitoring in the oil sands area resulted from the information received from these organizations and detailed fact sheets were presented for each one of the programs. The report of this study also presents seven other environmental monitoring initiatives or organizations such as Alberta Environment and Environment Canada environmental effects monitoring program. The main observation that emerged from the review was the lack of detailed understanding shown by the stakeholders regarding the monitoring activities performed in the oil sands area. There is a lack of communication of the different programs that are conducted in the region. The study also pointed out that no efforts were put in cross-linking the various programs to be assured that every concerns related to environmental effects associated with oil sands operations were addressed. A better understanding of environmental effects and an improvement in public confidence in the data and its interpretation would probably be observed with the establishment of a

Saltation of non-spherical sand particles.

Directory of Open Access Journals (Sweden)

Zhengshi Wang

Full Text Available Saltation is an important geological process and the primary source of atmospheric mineral dust aerosols. Unfortunately, no studies to date have been able to precisely reproduce the saltation process because of the simplified theoretical models used. For example, sand particles in most of the existing wind sand movement models are considered to be spherical, the effects of the sand shape on the structure of the wind sand flow are rarely studied, and the effect of mid-air collision is usually neglected. In fact, sand grains are rarely round in natural environments. In this paper, we first analyzed the drag coefficients, drag forces, and starting friction wind speeds of sand grains with different shapes in the saltation process, then established a sand saltation model that considers the coupling effect between wind and the sand grains, the effect of the mid-air collision of sand grains, and the effect of the sand grain shape. Based on this model, the saltation process and sand transport rate of non-spherical sand particles were simulated. The results show that the sand shape has a significant impact on the saltation process; for the same wind speed, the sand transport rates varied for different shapes of sand grains by as much as several-fold. Therefore, sand shape is one of the important factors affecting wind-sand movement.

Database of full-scale laboratory experiments on wave-driven sand transport processes

NARCIS (Netherlands)

van der Werf, Jebbe J.; Schretlen, Johanna Lidwina Maria; Ribberink, Jan S.; O'Donoghue, Tom

2009-01-01

A new database of laboratory experiments involving sand transport processes over horizontal, mobile sand beds under full-scale non-breaking wave and non-breaking wave-plus-current conditions is described. The database contains details of the flow and bed conditions, information on which quantities

Guide to preparing SAND reports. Revised

Energy Technology Data Exchange (ETDEWEB)

Locke, T.K. [ed.

1996-04-01

This guide contains basic information needed to produce a SAND report. Its guidelines reflect DOE regulation and Sandia policy. The guide includes basic writing instructions in an annotated sample report; guidance for organization, format, and layout of reports produced by line organizations; and information about conference papers, journal articles, and brochures. The appendixes contain sections on Sandia`s preferred usage, equations, references, copyrights and permissions, and publishing terms.

Provenance and recycling of Arabian desert sand

Science.gov (United States)

Garzanti, Eduardo; Vermeesch, Pieter; Andò, Sergio; Vezzoli, Giovanni; Valagussa, Manuel; Allen, Kate; Kadi, Khalid A.; Al-Juboury, Ali I. A.

2013-05-01

-Batin fossil alluvial fan or even from Mesozoic sandstones of the Arabian margin accreted to the Cenozoic Zagros orogen. Due to extensive recycling and the fact that zircon is so resistant to weathering and erosion, the U-Pb age signatures are much less powerful a tracer of sedimentary provenance than framework petrography and heavy minerals. Actualistic provenance studies of dune fields at subcontinental scale shed light on the generation and homogenization of aeolian sand, and allow us to trace complex pathways of multistep sediment transport, thus providing crucial independent information for accurate palaeogeographic and palaeoclimatic reconstructions.

Study on Modified Sand Filtration Towards Water Quality of Wet Market Waste Water

Directory of Open Access Journals (Sweden)

Saad F.N.M.

2016-01-01

Full Text Available Investigation on the potential of sand filter as a pre-treatment of waste water was done in Kangar wet market, Perlis. Besides, the best composition of filter in order to treat wastewater based on BOD, COD, SS, AN, turbidity and pH levels are further examined. In this study, there are four types of sand filter composition which the medias consist of fine sand and coarse sand while the modified sand filter are consist of sand, course sand and activated carbon prepared from rice husk and coconut shells. After 10 weeks of treatment, the results show that the concentration of BOD, COD, SS, AN, turbidity and pH were reduced up to 86%, 84%, 63%, 88%, 73%, respectively while pH nearly to neutral with 6.83. Moreover, the result also revealed that the sand filter added with rice husk almost complied with Standard B of Malaysia Environmental Quality (Sewage Regulations 2009 as well as gives the highest number of WQI with 36.81. Overall, WQI obtained in this study are ranged from 12.77 to 36.81.

Numerical Evaluation of Size Effect on the Stress-Strain Behaviour of Geotextile-Reinforced Sand

DEFF Research Database (Denmark)

Hosseinpour, I.; Mirmoradi, S.H.; Barari, Amin

2010-01-01

This paper studies the effect of sample size on the stress-strain behavior and strength characteristics of geotextile reinforced sand using the finite element numerical analysis. The effect of sample size was investigated by studying the effects of varying the number of geotextile layers, the con......This paper studies the effect of sample size on the stress-strain behavior and strength characteristics of geotextile reinforced sand using the finite element numerical analysis. The effect of sample size was investigated by studying the effects of varying the number of geotextile layers...... on the mechanical behavior of reinforced sand decreases with an increase in the sample size....

Ground penetrating radar water content mapping of golf course green sand layers

Science.gov (United States)

Information on the spatial distribution of water content across the sand layer component of a golf course green can be important to golf course superintendents for evaluating drainage effectiveness and scheduling irrigation. To estimate the bulk water content of the sand layer at point locations ac...

Preliminary study of sand jets in water-capped artificial and real MFT

Energy Technology Data Exchange (ETDEWEB)

Cai, J.; Zhu, D.; Rajaratnam, N. [Alberta Univ., Edmonton, AB (Canada). Dept. of Civil and Environmental Engineering

2008-07-01

A preliminary study of sand jets in water-capped artificial and real MFT was presented. Background information on oil sands tailing reclamation including water capping and sand capping were first discussed, followed by background information to the study, including non-Newtonian fluids and laponite clay, the artificial clay used mainly in small amounts as a rheology modifier in industrial fluids and materials. Although laponite clay is insoluble in water, it hydrates to make a clear and colourless colloidal, which is thixotropic and also behaves as a Bingham plastic fluid. The benefit of using gels made from laponite is the ability to see through to observe the physical processes in it. The objectives of the study were to examine the dynamics of sand jets in water-capped laponite gel and real MFT; improve the understanding of physical processes related to MFT and sand/slurry operations in tailings ponds; and find potential applications in recycling processed water and decommissioning of tailings ponds. It was concluded that it is much more difficult for jets to penetrate water-capped MFT due to larger yield stress in MFT. Future studies will focus on density correction, viscosity adjustment, and sensitivity analysis. tabs., figs.

Liquefaction resistance of calcareous sands

International Nuclear Information System (INIS)

Sandoval Vallejo, Eimar

2012-01-01

Calcareous sands are unique in terms of their origin, mineralogy, shape, fragility and intra particle porosity. This article presents results from an experimental program carried out to study the liquefaction resistance of a calcareous sand retrieved from Cabo Rojo at Puerto Rico. The experimental program included mineralogical characterization, index properties, and undrained cyclic triaxial tests on isotropically consolidated reconstituted samples. Due to the large variation in the calcareous sand properties, results are compared with previous researches carried out on other calcareous sands around the world. Results showed a wide range in the liquefaction resistance of the studied calcareous sands. Cabo Rojo sand experienced greater liquefaction resistance than most of the calcareous sands used for comparison. Important differences in the excess pore pressure generation characteristics were also found.

Comparison of bacteria populations in clean and recycled sand used for bedding in dairy facilities.

Science.gov (United States)

Kristula, M A; Rogers, W; Hogan, J S; Sabo, M

2005-12-01

Bedding samples were collected twice from commercial dairy free-stall facilities that used recycled sand and clean sand in both the summer and winter. Collection began on the day sand was taken from the pile (d 0) and placed in the free stalls, and continued for 5 to 7 additional days. The number of colonies per gram of bedding of gram-negative bacteria, coliforms, Streptococcus spp., and Klebsiella spp. were estimated for each sand sample as well as amounts of dry and organic matter. Clean sand (CS) and recycled sand (RS) had the same bacterial counts when compared at any sampling time. The mean counts of bacterial populations did vary over the course of the study in both CS and RS. There was a significant increase in bacterial counts from d 0 to d 1 for gram-negative bacteria, coliforms, and Streptococcus spp. in both winter and summer. Counts of gram-negative bacteria, coliforms, Klebsiella spp., and Streptococcus spp. did not differ from d 1 to 7 in the winter. Total counts of gram-negative bacteria did not differ from d 1 to 7 in the summer. On d 1 in the summer, coliform counts were lower than at d 5 to 7, and Klebsiella spp. counts were lower than on d 3 to 7. Streptococcus spp. counts were high on d 1 and were constant through d 7 in both winter and summer trials. The number of coliform and Klebsiella spp. in both CS and RS was below the threshold thought to cause mastitis during the sampling times. The number of Streptococcus spp. was high in both CS and RS during the sampling periods. Other management factors need to be identified to decrease the number of Streptococcus spp. in bedding. Recycled sand had a higher organic matter and lower dry matter compared with CS in winter and summer. The results for this study were obtained from multiple herd comparisons, and herd was a significant effect suggesting that different management systems influence the number and types of bacteria in both CS and RS.

TYPE OF LIGHT IN SAND FLY CAPTURES (DIPTERA:PSYCHODIDAE

Directory of Open Access Journals (Sweden)

VERÔNICA DE LOURDES SIERPE JERALDO

2012-09-01

Full Text Available The number of cases of visceral leishmaniasis in Brazil has been gradually increasing, and one of the strategies to reduce the transmission of this disease is based on the control of the adult forms of its vectors. It is therefore of great epidemiological importance to develop more refined methods for monitoring and controlling its vectors, which are the phlebotomine sand flies, or biting midges. The present study compares the attraction exercised by UV light in comparison with conventional incandescent, or white, light in catching phlebotomine sand flies. Traps baited with UV light caught higher numbers of these flies than traps baited with white light, indicating the potential use of UV light, especially in locations of low demographic density of the flies.

Habitat selection models for Pacific sand lance (Ammodytes hexapterus) in Prince William Sound, Alaska

Science.gov (United States)

Ostrand, William D.; Gotthardt, Tracey A.; Howlin, Shay; Robards, Martin D.

2005-01-01

We modeled habitat selection by Pacific sand lance (Ammodytes hexapterus) by examining their distribution in relation to water depth, distance to shore, bottom slope, bottom type, distance from sand bottom, and shoreline type. Through both logistic regression and classification tree models, we compared the characteristics of 29 known sand lance locations to 58 randomly selected sites. The best models indicated a strong selection of shallow water by sand lance, with weaker association between sand lance distribution and beach shorelines, sand bottoms, distance to shore, bottom slope, and distance to the nearest sand bottom. We applied an information-theoretic approach to the interpretation of the logistic regression analysis and determined importance values of 0.99, 0.54, 0.52, 0.44, 0.39, and 0.25 for depth, beach shorelines, sand bottom, distance to shore, gradual bottom slope, and distance to the nearest sand bottom, respectively. The classification tree model indicated that sand lance selected shallow-water habitats and remained near sand bottoms when located in habitats with depths between 40 and 60 m. All sand lance locations were at depths lance and the independent variables are discussed.

A Threshold Continuum for Aeolian Sand Transport

Science.gov (United States)

Swann, C.; Ewing, R. C.; Sherman, D. J.

2015-12-01

The threshold of motion for aeolian sand transport marks the initial entrainment of sand particles by the force of the wind. This is typically defined and modeled as a singular wind speed for a given grain size and is based on field and laboratory experimental data. However, the definition of threshold varies significantly between these empirical models, largely because the definition is based on visual-observations of initial grain movement. For example, in his seminal experiments, Bagnold defined threshold of motion when he observed that 100% of the bed was in motion. Others have used 50% and lesser values. Differences in threshold models, in turn, result is large errors in predicting the fluxes associated with sand and dust transport. Here we use a wind tunnel and novel sediment trap to capture the fractions of sand in creep, reptation and saltation at Earth and Mars pressures and show that the threshold of motion for aeolian sand transport is best defined as a continuum in which grains progress through stages defined by the proportion of grains in creep and saltation. We propose the use of scale dependent thresholds modeled by distinct probability distribution functions that differentiate the threshold based on micro to macro scale applications. For example, a geologic timescale application corresponds to a threshold when 100% of the bed in motion whereas a sub-second application corresponds to a threshold when a single particle is set in motion. We provide quantitative measurements (number and mode of particle movement) corresponding to visual observations, percent of bed in motion and degrees of transport intermittency for Earth and Mars. Understanding transport as a continuum provides a basis for revaluating sand transport thresholds on Earth, Mars and Titan.

Mapping of sand deposition from 1993 midwest floods with electromagnetic induction measurements

International Nuclear Information System (INIS)

Kitchen, N.R.; Sudduth, K.A.; Drummond, S.T.

1996-01-01

Sand deposition on river-bottom farmland was extensive from the 1993 Midwest floods. A technique coupling electromagnetic induction (EM) ground conductivity sensing and Global Positioning System (GPS) location data was used to map sand deposition depth at four sites in Missouri along the Missouri River. A strong relationship between EM reading and probe measured depth of sand deposition (r 2 values between 0.73-0.94) was found. This relationship differed significantly between sites, so calibration by ground-truthing was required for each sand deposition survey. An example of the sand deposition mapping using the EM/GPS system is shown for two 50-60 ha (125-150 ac) sites. Such maps can provide valuable detailed information for developing restoration plans for land affected by 1993 Midwest floods. (author)

MECHANICAL REGENERATION OF SAND WASTE

Directory of Open Access Journals (Sweden)

D. I. Gnir

2005-01-01

Full Text Available The experimental activation of the sand regenerator of the firm SINTO is carried out at ОАО “MZOO". It is shown that sand grains are cleared from films of binding agents, that allows to use the treated sand for preparation of agglutinant and core sands.

Proceedings of the Canadian oil sands forum 2007 : creating excellence through innovation

International Nuclear Information System (INIS)

2007-01-01

The supply from Canada's oil sands industry is growing at an accelerated pace. This conference was intended for professionals in the oil sands industry seeking updated information on oil sands developments, transportation issues and future market challenges and opportunities. It was attended by a broad range of industry participants who addressed some of the critical issues involved in developing oil sands projects. Despite market opportunities which have resulted in a fast pace of development and continually evolving project plans, there are challenges and uncertainties that must be overcome in order to achieve projected levels of supply growth. It was noted that the business environment in the oil sands industry is continually changing in terms of current supply/market/refining situations and new market developments. The conference also addressed how capital cost and mega-project management issues are being addressed. Expanding market opportunities for Canada's growing oil sands supply were highlighted along with latest developments related to upgrading strategies. Market experts also discussed issues related to synthetic crude, heavy oil markets and the supply and demand of diluents. The sessions were entitled: challenges and opportunities in oil sands; oil sands business outlook; latest project development updates; integration of Canadian oil sands with U.S. refining; and, technology and oil sands innovations.The conference featured 16 presentations, of which 6 have been catalogued separately for inclusion in this database. tabs., figs

Crushed rock sand – An economical and ecological alternative to natural sand to optimize concrete mix

Directory of Open Access Journals (Sweden)

Sanjay Mundra

2016-09-01

Full Text Available The study investigates the use of crushed rock sand as viable alternative to Natural River sand that is being conventionally used as fine aggregate in cement concrete. Various mix designs were developed for different grades of concrete based on IS, ACI and British codes using Natural River sand and crushed rock sand. In each case, the cube compressive strength test, and beam flexure tests were conducted. The results of the study show that, the strength properties of concrete using crushed rock sand are nearly similar to the conventional concrete. The study has shown that crushed stone sand can be used as economic and readily available alternative to river sand and can therefore help to arrest the detrimental effects on the environment caused due to excessive mining of river sand.

Characterisation of radioactivity carrying aerosol in a mineral sand processing plant

International Nuclear Information System (INIS)

Jeffries, C.; Morawska, L.

1998-01-01

The techniques used to separate heavy mineral sand into mineral products produce a large amount of airborne particulate. Some of these particles are radioactive which is due to the thorium and, to a lesser extent, the uranium content of mineral sands. This study has investigated both the radioactive and respirable particle components (<10 μm) of the aerosol in a dry sand processing plant in Brisbane, Australia. A number of different measurement techniques have been used to characterise the aerosol in the plant. The mass, number and activity distributions have been determined by an eight stage cascade impactor and an Aerodynamic Particle Sizer (APS) with both instruments measuring 0.4 to 10 μm. Measurements of radon progeny concentrations and the extent of radon progeny attachment to micrometer sized particles has been investigated, as well as the extent of airborne thorium and uranium. The preliminary results from two sites are presented and comments are made on the relationship between total and radioactive aerosol

Rheological Characterization of Green Sand Flow

DEFF Research Database (Denmark)

Jabbaribehnam, Mirmasoud; Spangenberg, Jon; Hovad, Emil

2016-01-01

The main aim of this paper is to characterize experimentally the flow behaviour of the green sand that is used for casting of sand moulds. After the sand casting process is performed, the sand moulds are used for metal castings. The rheological properties of the green sand is important to quantif...

Sustainable water management in Alberta's oil sands

Energy Technology Data Exchange (ETDEWEB)

Byers, Bill; Usher, Robyn; Roach, Andrea [CH2M HILL, Englewood, CO (United States); Lambert, Gord; Kotecha, Prit [Suncor Energy Inc., Calgary (Canada)

2012-07-01

The Canadian Association of Petroleum Producers forecast published in 2011 predicts that oil production from oil sands will increase by 50% in the next 3 years and double by 2020. This rate of growth will result in significant pressure on water resources; water use per barrel of oil sands production is comparable to other energy resources - about 2.5 barrels of fresh water per barrel of oil produced are used by mining operations and 0.5 barrels by in-situ operations. Suncor Energy Inc. (Suncor) was the first company to develop the oil sands in northern Alberta and holds one of the largest oil sands positions in Canada. In 2010, Suncor announced plans to increase production to more than 1 million barrels of oil equivalent per day by 2020, which it plans to achieve through oil sands production growth of approximately 10% per year. Because water supply and potential impacts to water quality are critical to its future growth, in 2010-2011 Suncor conducted a risk assessment to identify water-related business risks related to its northern Alberta operations. The assessment identified more than 20 high level business risks in strategic water risk areas including water supply, water reuse, storm water management, groundwater, waste management and river water return. The risk assessment results prompted development of a strategic roadmap to guide water stewardship across Suncor's regional operations. The roadmap describes goals, objectives, and specific activities for each of six key water risk areas, and informs prioritization and selection of prospective water management activities. Suncor is not only exploring water within its own boundaries, but is also collaborating with other oil sands producers to explore ways of integrating its water systems through industry consortia; Suncor is a member of the Oil Sands Leadership Initiative and of the recently formed Canadian Oil Sands Innovation Alliance, among others. (author)

Pharmacotherapy for social anxiety disorder (SAnD).

Science.gov (United States)

Williams, Taryn; Hattingh, Coenraad J; Kariuki, Catherine M; Tromp, Sean A; van Balkom, Anton J; Ipser, Jonathan C; Stein, Dan J

2017-10-19

Recognition is growing that social anxiety disorder (SAnD) is a chronic and disabling disorder, and data from early trials demonstrate that medication may be effective in its treatment. This systematic review is an update of an earlier review of pharmacotherapy of SAnD. To assess the effects of pharmacotherapy for social anxiety disorder in adults and identify which factors (methodological or clinical) predict response to treatment. We searched the Cochrane Common Mental Disorders Controlled Trials Register (CCMDCTR-Studies and CCMDCTR-References) to 17 August 2015. The CCMDCTR contains reports of relevant RCTs from MEDLINE (1950-), Embase (1974-), PsycINFO (1967-) and CENTRAL (all years). We scanned the reference lists of articles for additional studies. We updated the search in August 2017 and placed additional studies in Awaiting Classification, these will be incorporated in the next version of the review, as appropriate. We restricted studies to randomised controlled trials (RCTs) of pharmacotherapy versus placebo in the treatment of SAnD in adults. Two authors (TW and JI) assessed trials for eligibility and inclusion for this review update. We extracted descriptive, methodological and outcome information from each trial, contacting investigators for missing information where necessary. We calculated summary statistics for continuous and dichotomous variables (if provided) and undertook subgroup and sensitivity analyses. We included 66 RCTs in the review (> 24 weeks; 11,597 participants; age range 18 to 70 years) and 63 in the meta-analysis. For the primary outcome of treatment response, we found very low-quality evidence of treatment response for selective serotonin reuptake inhibitors (SSRIs) compared with placebo (number of studies (k) = 24, risk ratio (RR) 1.65; 95% confidence interval (CI) 1.48 to 1.85, N = 4984). On this outcome there was also evidence of benefit for monoamine oxidase inhibitors (MAOIs) (k = 4, RR 2.36; 95% CI 1.48 to 3.75, N = 235

Canada's oil sands : opportunities and challenges to 2015 : an update

International Nuclear Information System (INIS)

2006-06-01

This report updated an energy market assessment compiled and published by the National Energy Board (NEB) in 2004. Major changes resulting from recent developments in the oil sands industry were presented. The report was compiled from a series of informal meetings and discussions with a cross-section of oil sands stakeholders. Influences on recent oil sands development and production growth included market development and pipelines; rising capital and labour costs; operating costs; environmental impact management; high crude oil prices; rising global energy demand; technology innovations; and a more stable investment climate. A comparison of key assumptions between the current analysis and the 2004 report was presented, along with estimates of operating and supply costs for various types of oil sands recovery methods. Potential markets for oil sands production were reviewed. Environmental and socio-economic impacts on the industry included the larger than anticipated water withdrawals from the Athabasca River for mining operations; and uncertainties over land reclamation methods. The industry has also been impacted by a limited supply of skilled workers in Alberta. It was observed that the potential for building cogeneration capacity has decreased since the 2004 report. It was concluded that the oil sands industry will continue to grow rapidly, but the rate of development will depend on the balance that is reached between the opposing forces that affect the oil sands. Natural gas costs, high oil prices, air emissions management issues and water usage will continue to be of concern. 6 tabs., 7 figs

Undrained Cyclic Behaviour of Dense Frederikshavn Sand

DEFF Research Database (Denmark)

Nielsen, Søren Kjær; Ibsen, Lars Bo; Sørensen, Kris Wessel

2013-01-01

A modified contour diagram is created for the Frederikshavn Sand in the undrained case for a relative density of ID = 80 %. It can be used to estimate the number of cycles to failure for a given combination of pore pressure, average and cyclic load ratio. The diagram is based on a series of undra...

Compressive behavior of fine sand.

Energy Technology Data Exchange (ETDEWEB)

Martin, Bradley E. (Air Force Research Laboratory, Eglin, FL); Kabir, Md. E. (Purdue University, West Lafayette, IN); Song, Bo; Chen, Wayne (Purdue University, West Lafayette, IN)

2010-04-01

The compressive mechanical response of fine sand is experimentally investigated. The strain rate, initial density, stress state, and moisture level are systematically varied. A Kolsky bar was modified to obtain uniaxial and triaxial compressive response at high strain rates. A controlled loading pulse allows the specimen to acquire stress equilibrium and constant strain-rates. The results show that the compressive response of the fine sand is not sensitive to strain rate under the loading conditions in this study, but significantly dependent on the moisture content, initial density and lateral confinement. Partially saturated sand is more compliant than dry sand. Similar trends were reported in the quasi-static regime for experiments conducted at comparable specimen conditions. The sand becomes stiffer as initial density and/or confinement pressure increases. The sand particle size become smaller after hydrostatic pressure and further smaller after dynamic axial loading.

The Diversity of Yellow-Related Proteins in Sand Flies (Diptera: Psychodidae.

Directory of Open Access Journals (Sweden)

Michal Sima

Full Text Available Yellow-related proteins (YRPs present in sand fly saliva act as affinity binders of bioamines, and help the fly to complete a bloodmeal by scavenging the physiological signals of damaged cells. They are also the main antigens in sand fly saliva and their recombinant form is used as a marker of host exposure to sand flies. Moreover, several salivary proteins and plasmids coding these proteins induce strong immune response in hosts bitten by sand flies and are being used to design protecting vaccines against Leishmania parasites. In this study, thirty two 3D models of different yellow-related proteins from thirteen sand fly species of two genera were constructed based on the known protein structure from Lutzomyia longipalpis. We also studied evolutionary relationships among species based on protein sequences as well as sequence and structural variability of their ligand-binding site. All of these 33 sand fly YRPs shared a similar structure, including a unique tunnel that connects the ligand-binding site with the solvent by two independent paths. However, intraspecific modifications found among these proteins affects the charges of the entrances to the tunnel, the length of the tunnel and its hydrophobicity. We suggest that these structural and sequential differences influence the ligand-binding abilities of these proteins and provide sand flies with a greater number of YRP paralogs with more nuanced answers to bioamines. All these characteristics allow us to better evaluate these proteins with respect to their potential use as part of anti-Leishmania vaccines or as an antigen to measure host exposure to sand flies.

Alberta's oil sands fiscal system : historical context and system performance

International Nuclear Information System (INIS)

2007-01-01

This report described the fiscal system applied to Alberta's oil sands. It is the first technical report forming part of a series designed to provide information and to invite comment as part of the Government of Alberta's public review of the fiscal system applied to the province's oil and gas resources. Specifically, this report assessed the robustness of Alberta's oil sands fiscal system and assessed how the regime balanced the risks and rewards to both investors and Albertans across a range of expected and probable economic outcomes. The report provided an explanation of the history and context of Alberta's royalty regime and included a case-by-case approach. It also provided a discussion of the oil sands fiscal system description. Next, it described the methodology employed for the analysis of the oil sands fiscal system. It also provided the assumptions for 5 scenario cases and presented the fiscal map approach for assessing project economics and fiscal system performance. Last, summary observations were presented. It was found that the oil sands fiscal system is very flexible for adverse economic conditions and much less so for highly profitable conditions. tabs., figs

Effect of Natural Sand Percentages on Fatigue Life of Asphalt Concrete Mixture

Directory of Open Access Journals (Sweden)

Nahla Yassub Ahmed

2016-03-01

Full Text Available The design of a flexible pavement requires the knowledge of the material properties which are characterized by stiffness and fatigue resistance. The fatigue resistance relates the number of load cycles to failure with the strain level applied to the asphalt mixture. The main objective of this research is the evaluation of the fatigue life of asphalt mixtures by using two types of fine aggregate having different percentages. In this study, two types of fine aggregate were used natural sand (desert sand and crushed sand. The crushed sand was replaced by natural sand (desert sand with different percentages (0%, 25%, 75% and 100% by the weight of the sand (passing sieve No.8 and retained on sieve No.200 and one type of binder (40/50 penetration from Al-Daurah refinery. The samples of beams were tested by four point bending beam fatigue test at the control strain mode (250, 500 and 750 microstrain while the loading frequency (5Hz and testing temperature (20oC according to (AASHTO T321. The experimental work showed that fatigue life (Nf and initial flexural stiffness increased when control strain decreased for asphalt mixtures. Acceptable fatigue life at 750 microstrain was obtained with asphalt concrete mixtures containing 100% crushed sand as well as asphalt concrete contained 25% natural sand. The asphalt concrete contained 100% and 75% of natural sand exhibited high fatigue life at low level of microstrain (250. The main conclusion of this study found that best proportion of natural sand to be added to an asphaltic concrete mixture is falling within the range (0% and 25% by weight of fraction (passing No.8 and retained on No.200 sieve .

Radiation protection in the mineral sands industry in New South Wales

International Nuclear Information System (INIS)

Carter, M.W.; Coundouris, A.N.

1993-01-01

The mineral sands industry in New South Wales (NSW) mines and concentrates the heavy minerals ilmenite, rutile, zircon and monazite; principally for export. Mineral sands concentrates contain small quantities of thorium and uranium series radionuclides and therefore are radioactive. The protection of workers, the public and the environment is a responsibility of mine operators. NSW Government Departments administer legislation, grant approvals and specify conditions for radiation protection. A summary of the history and current size of the industry is presented, together with current legislative and licensing activities. The paper reviews available literature on radiation measurements in the East coast mineral sands industry and re-interprets the earlier data in the light of the contemporary methodology of dose assessment. Some unpublished information and the results of some new surveys are also presented. A comparison is made with results that have been reported from Western Australia. Procedures for reducing radiation exposures are discussed and areas of future information needs are suggested. 17 refs., 6 refs., 3 tabs

Modeling and Optimization of Phenol Formaldehyde Resin Sand Mould System

Directory of Open Access Journals (Sweden)

Chate G. R.

2017-06-01

Full Text Available Chemical bonded resin sand mould system has high dimensional accuracy, surface finish and sand mould properties compared to green sand mould system. The mould cavity prepared under chemical bonded sand mould system must produce sufficient permeability and hardness to withstand sand drop while pouring molten metal through ladle. The demand for improved values of permeability and mould hardness depends on systematic study and analysis of influencing variables namely grain fineness number, setting time, percent of resin and hardener. Try-error experiment methods and analysis were considered impractical in actual foundry practice due to the associated cost. Experimental matrices of central composite design allow conducting minimum experiments that provide complete insight of the process. Statistical significance of influencing variables and their interaction were determined to control the process. Analysis of variance (ANOVA test was conducted to validate the model statistically. Mathematical equation was derived separately for mould hardness and permeability, which are expressed as a non-linear function of input variables based on the collected experimental input-output data. The developed model prediction accuracy for practical usefulness was tested with 10 random experimental conditions. The decision variables for higher mould hardness and permeability were determined using desirability function approach. The prediction results were found to be consistent with experimental values.

A combined CFD-experimental method for developing an erosion equation for both gas-sand and liquid-sand flows

Science.gov (United States)

Mansouri, Amir

The surface degradation of equipment due to consecutive impacts of abrasive particles carried by fluid flow is called solid particle erosion. Solid particle erosion occurs in many industries including oil and gas. In order to prevent abrupt failures and costly repairs, it is essential to predict the erosion rate and identify the locations of the equipment that are mostly at risk. Computational Fluid Dynamics (CFD) is a powerful tool for predicting the erosion rate. Erosion prediction using CFD analysis includes three steps: (1) obtaining flow solution, (2) particle tracking and calculating the particle impact speed and angle, and (3) relating the particle impact information to mass loss of material through an erosion equation. Erosion equations are commonly generated using dry impingement jet tests (sand-air), since the particle impact speed and angle are assumed not to deviate from conditions in the jet. However, in slurry flows, a wide range of particle impact speeds and angles are produced in a single slurry jet test with liquid and sand particles. In this study, a novel and combined CFD/experimental method for developing an erosion equation in slurry flows is presented. In this method, a CFD analysis is used to characterize the particle impact speed, angle, and impact rate at specific locations on the test sample. Then, the particle impact data are related to the measured erosion depth to achieve an erosion equation from submerged testing. Traditionally, it was assumed that the erosion equation developed based on gas testing can be used for both gas-sand and liquid-sand flows. The erosion equations developed in this work were implemented in a CFD code, and CFD predictions were validated for various test conditions. It was shown that the erosion equation developed based on slurry tests can significantly improve the local thickness loss prediction in slurry flows. Finally, a generalized erosion equation is proposed which can be used to predict the erosion rate in

New records of phlebotomine sand flies (Diptera: Psychodidae from Ecuador

Directory of Open Access Journals (Sweden)

J. Bruce Alexander

1992-03-01

Full Text Available The plebotomine sand fly fauna of Ecuador was surveyed in two 3-month collecting trips made in 1988 and 1990. A total of 12 provinces were visited, including three (Bolivar, Loja and Morona Santiago from wich no previous records to phlebotomines existed. Forty-six species were collected, 13 of wich, together with 1 subspecies and 1 genus (Warileya represented new records for the country. This survey increases the known number of species in Ecuador to 60. The distribuition of Ecuadorian sand flies is discussed in the light of these new findings.

Simulating Sand Behavior through Terrain Subdivision and Particle Refinement

Science.gov (United States)

Clothier, M.

2013-12-01

Advances in computer graphics, GPUs, and parallel processing hardware have provided researchers with new methods to visualize scientific data. In fact, these advances have spurred new research opportunities between computer graphics and other disciplines, such as Earth sciences. Through collaboration, Earth and planetary scientists have benefited by using these advances in hardware technology to process large amounts of data for visualization and analysis. At Oregon State University, we are collaborating with the Oregon Space Grant and IGERT Ecosystem Informatics programs to investigate techniques for simulating the behavior of sand. In addition, we have also been collaborating with the Jet Propulsion Laboratory's DARTS Lab to exchange ideas on our research. The DARTS Lab specializes in the simulation of planetary vehicles, such as the Mars rovers. One aspect of their work is testing these vehicles in a virtual "sand box" to test their performance in different environments. Our research builds upon this idea to create a sand simulation framework to allow for more complex and diverse environments. As a basis for our framework, we have focused on planetary environments, such as the harsh, sandy regions on Mars. To evaluate our framework, we have used simulated planetary vehicles, such as a rover, to gain insight into the performance and interaction between the surface sand and the vehicle. Unfortunately, simulating the vast number of individual sand particles and their interaction with each other has been a computationally complex problem in the past. However, through the use of high-performance computing, we have developed a technique to subdivide physically active terrain regions across a large landscape. To achieve this, we only subdivide terrain regions where sand particles are actively participating with another object or force, such as a rover wheel. This is similar to a Level of Detail (LOD) technique, except that the density of subdivisions are determined by

On Pluvial Compaction of Sand

DEFF Research Database (Denmark)

Jacobsen, Moust

At the Institute of Civil Engineering in Aalborg model tests on dry sand specimens have been carried out during the last five years. To reduce deviations in test results, the sand laying technique has been carefully studied, and the sand mass spreader constructed. Preliminary results have been...

MORPHOMETRIC CHARACTERIZATION OF THE SAND FRACTION IN A SAND GRAIN IMAGE CAPTURE SYSTEM1

Directory of Open Access Journals (Sweden)

Lucimar Arruda Viana

Full Text Available ABSTRACT Morphology studies assume significant importance in analysis of phenomena of granular systems packaging, in particular with a view to the use of the technique of soil stabilization named particle size correction in forest roads. In this context, this study aimed to develop and operationalize a Sand Grain Image Capture System and, hereby, determine the morphological indices of the sand fractions of two sandy soils called João Pinheiro (JP and Cachoeira da Prata (CP. Soil samples, air-dried, were sieved (2.0 mm nominal mesh size for removal of gravels. The materials that passed through the sieve were subjected to dispersion, washing in 0.053 mm nominal mesh size sieve, removal of organic matter and iron oxides to obtain the clean sand fractions. Subsequently, each soil sample was sieved for separation into twelve classes, between the diameters of 0.149 mm and 1.190 mm, using a Rotap shaker. Next, tests were carried out to characterize the morphometric attributes of the twelve classes of sand fractions of the soils studied. For validation of the performance of the Sand Grain Image Capture System, the results were compared to those obtained using a standard procedure for image analysis. The analysis of the results led to the following conclusions: (i the sand fraction of the JP soil presented higher values for the morphometric indices roundness, elongation and compactness compared to sand fraction of the CP soil; and (ii the Sand Grain Image Capture System worked properly, with practicality.

Technology unlocks tar sands energy

Energy Technology Data Exchange (ETDEWEB)

Law, C

1967-09-25

Tar sand processing technology has been developed primarily in the categories of extraction techniques and in-situ processing. In October, a $235 million venture into tar sand processing will be inspected by visitors from many points on the globe. A synthetic crude of premium quality will be flowing through a 16-in. pipeline from the Tar Island plant site of Great Canadian Oil Sands to Edmonton. This processing plant uses an extractive mining technique. The tar sand pay zone in this area averages approximately 150 ft in thickness with a 50-ft overburden. It has been estimated that the tar sands cannot be exploited when the formation thickness is less than 100 ft and overburden exceeds the same amount. This indicates that extraction techniques can only be used to recover approximately 15% of the tar sand deposits. An in-situ recovery technique developed by Shell of Canada is discussed in detail. In essence it is selective hydraulic fracturing, followed by the injection of emulsifying chemicals and steam.

Bituminous sands : tax issues

International Nuclear Information System (INIS)

Patel, B.

2004-01-01

This paper examined some of the tax issues associated with the production of bitumen or synthetic crude oil from oil sands. The oil sands deposits in Alberta are gaining more attention as the supplies of conventional oil in Canada decline. The oil sands reserves located in the Athabasca, Cold Lake and Peace River areas contain about 2.5 trillion barrels of highly viscous hydrocarbons called bitumen, of which nearly 315 billion barrels are recoverable with current technology. The extraction method varies for each geographic area, and even within zones and reservoirs. The two most common extraction methods are surface mining and in-situ extraction such as cyclic steam stimulation (CSS); low pressure steam flood; pressure cycle steam drive; steam assisted gravity drainage (SAGD); hot water flooding; and, fire flood. This paper also discussed the following general tax issues: bituminous sands definition; bituminous sands leases and Canadian development expense versus Canadian oil and gas property expense (COGPE); Canadian exploration expense (CEE) for surface mining versus in-situ methods; additional capital cost allowance; and, scientific research and experimental development (SR and ED). 15 refs

Oil sands tax expenditures

International Nuclear Information System (INIS)

Ketchum, K; Lavigne, R.; Plummer, R.

2001-01-01

The oil sands are a strategic Canadian resource for which federal and provincial governments provide financial incentives to develop and exploit. This report describes the Oil Sands Tax Expenditure Model (OSTEM) developed to estimate the size of the federal income tax expenditure attributed to the oil sands industry. Tax expenditures are tax concessions which are used as alternatives to direct government spending for achieving government policy objectives. The OSTEM was developed within the business Income Tax Division of Canada's Department of Finance. Data inputs for the model were obtained from oil sands developers and Natural Resources Canada. OSTEM calculates annual revenues, royalties and federal taxes at project levels using project-level projections of capital investment, operating expenses and production. OSTEM calculates tax expenditures by comparing taxes paid under different tax regimes. The model also estimates the foregone revenue as a percentage of capital investment. Total tax expenditures associated with investment in the oil sands are projected to total $820 million for the period from 1986 to 2030, representing 4.6 per cent of the total investment. 10 refs., 2 tabs., 7 figs

Singing Sand Dunes

Indian Academy of Sciences (India)

ble low-frequency (s. 75–105 Hz), that can some- times be heard up to 10 km away. Scientific in- vestigations suggest that the sustained low fre- quency sound of sand dunes that resembles a pure note from a musical instrument, is due to the synchronized motion of well-sorted dry sand grains when they spontaneously ...

Solution weighting for the SAND-II Monte Carlo code

International Nuclear Information System (INIS)

Oster, C.A.; McElroy, W.N.; Simons, R.L.; Lippincott, E.P.; Odette, G.R.

1976-01-01

Modifications to the SAND-II Error Analysis Monte Carlo code to include solution weighting based on input data uncertainties have been made and are discussed together with background information on the SAND-II algorithm. The new procedure permits input data having smaller uncertainties to have a greater influence on the solution spectrum than do the data having larger uncertainties. The results of an indepth study to find a practical procedure and the first results of its application to three important Interlaboratory LMFBR Reaction Rate (ILRR) program benchmark spectra (CFRMF, ΣΣ, and 235 U fission) are discussed

Aeolian sands as material to construct low-volume roads

CSIR Research Space (South Africa)

Paige-Green, P

2011-07-01

Full Text Available Aeolian sands are widespread in many semi-arid to arid areas of the world and often provide the only economic source of construction materials for low volume roads. Experience in southern Africa over a number of decades has shown that provided...

Vehicle non-exhaust emissions from the tyre-road interface - effect of stud properties, traction sanding and resuspension

Science.gov (United States)

Kupiainen, Kaarle J.; Pirjola, Liisa

2011-08-01

In Northern cities respirable street dust emission levels (PM 10) are especially high during spring. The spring time dust has been observed to cause health effects as well as discomfort among citizens. Major sources of the dust are the abrasion products from the pavement and traction sand aggregates that are formed due to the motion of the tyre. We studied the formation of respirable abrasion particles in the tyre-road interface due to tyre studs and traction sanding by a mobile laboratory vehicle Sniffer. The measurements were preformed on a test track, where the influence of varying stud weight and stud number per tyre on PM 10 emissions was studied. Studded tyres resulted in higher emission levels than studless tyres especially with speeds 50 km h -1 and higher; however, by using light weight studs, which approximately halves the weight of studs, or by reducing the number of studs per tyre to half, the emission levels decreased by approximately half. Additionally measurements were done with and without traction sand coverage on the pavement of a public road. After traction sanding the emission levels were not affected by tyre type but by formation and suspension of traction sand related dust from the road surface. The emissions after traction sanding decreased as a function of time as passing vehicles' motion shifted the sand grains away from the areas with most tyre-road contact.

Field evaluation of a new light trap for phlebotomine sand flies.

Science.gov (United States)

Gaglio, Gabriella; Napoli, Ettore; Falsone, Luigi; Giannetto, Salvatore; Brianti, Emanuele

2017-10-01

Light traps are one of the most common attractive method for the collection of nocturnal insects. Although light traps are generally referred to as "CDC light traps", different models, equipped with incandescent or UV lamps, have been developed. A new light trap, named Laika trap 3.0, equipped with LED lamps and featured with a light and handy design, has been recently proposed into the market. In this study we tested and compared the capture performances of this new trap with those of a classical light trap model under field conditions. From May to November 2013, a Laika trap and a classical light trap were placed biweekly in an area endemic for sand flies. A total of 256 sand fly specimens, belonging to 3 species (Sergentomyia minuta, Phlebotomus perniciosus, Phlebotomus neglectus) were collected during the study period. The Laika trap captured 126 phlebotomine sand flies: P. perniciosus (n=38); S. minuta (n=88), a similar number of specimens (130) and the same species were captured by classical light trap which collected also 3 specimens of P. neglectus. No significant differences in the capture efficiency at each day of trapping, neither in the number of species or in the sex of sand flies were observed. According to results of this study, the Laika trap may be a valid alternative to classical light trap models especially when handy design and low power consumption are key factors in field studies. Copyright © 2017 Elsevier B.V. All rights reserved.

Field test on sand compaction pile method with copper slag sand; Dosuisai slag wo mochiita SCP koho no shiken seko

Energy Technology Data Exchange (ETDEWEB)

Minami, K.; Matsui, H.; Naruse, E.; Kitazume, M. [Port and Harbour Research Inst., Kanagawa (Japan)

1997-09-20

This paper describes the sand compaction pile (SCP) method using copper slag sand. The SCP method is a method by which sand compaction piles are constructed in the ground, and improvement can be obtained in a short period. This method has been widely used even in the port areas for enhancing the bearing power of soft clay ground and the lateral resistance of sheet pile. A great deal of sand is required as a material. The sand requires high permeability, proper size distribution with less fine particle fraction content, easy compaction property with enough strength, and easy discharging property from the casing of construction machines as required properties. Recently, it becomes hard to secure proper sand materials. The copper slag sand is obtained from refining process of copper as a by-product which is quenched in water flow and crushed in water. The copper slag sand has higher particle density than that of sand, excellent permeability, and similar size distribution to that of sand. From compaction drainage triaxial compression test and permeability test, it was found that the mechanical properties of copper slag sand did not change by the crushing of grains with keeping excellent permeability. Through the test construction, applicability of the copper slag sand to the SCP method could be confirmed as an alternate material of sand. 17 refs., 9 figs., 4 tabs.

Efficacy of Different Sampling Methods of Sand Flies (Diptera: Psychodidae in Endemic Focus of Cutaneous Leishmaniasis in Kashan District, Isfahan Province, Iran.

Directory of Open Access Journals (Sweden)

Marzieh Hesam-Mohammadi

2014-12-01

Full Text Available The aim of the study was to evaluate and compare the efficiency and practicality of seven trapping methods for adult phlebotominae sand flies. The results of this investigation provide information to determine the species composition and nocturnal activity pattern of different sand fly species.The study was carried out in both plain region (about 5km far from northeast and mountainous region (about 40km far from southwest of Kashan City. Seven traps were selected as sampling methods and sand flies were collected during 5 interval times starting July to September 2011 and from 8:00PM to 6:00AM in outdoors habitats. The traps include: sticky traps (4 papers for 2 hours, Disney trap, Malaise, CDC and CO2 light traps, Shannon traps (black and white nets and animal-baited trap.A total of 1445 sand flies belonging to 15 species of Phlebotomus spp. and five of Sergentomyia spp. were collected. Females and males comprised 44.91% and 55.09% of catches, respectively. Of the collected specimens, Se. sintoni was found to be the most prevalent (37.86% species, while Ph. papatasi, accounted for 31.76% of the sand flies.Disney trap and sticky traps exhibited the most productivity than other traps. In addition, in terms of the efficiency of sampling method, these two trapping methods appeared to be the most productive for both estimating the number of sand flies and the species composition in the study area.

Infection parameters in the sand fly vector that predict transmission of Leishmania major.

Science.gov (United States)

Stamper, Lisa W; Patrick, Rachel L; Fay, Michael P; Lawyer, Phillip G; Elnaiem, Dia-Eldin A; Secundino, Nagila; Debrabant, Alain; Sacks, David L; Peters, Nathan C

2011-08-01

To identify parameters of Leishmania infection within a population of infected sand flies that reliably predict subsequent transmission to the mammalian host, we sampled groups of infected flies and compared infection intensity and degree of metacyclogenesis with the frequency of transmission. The percentage of parasites within the midgut that were metacyclic promastigotes had the highest correlation with the frequency of transmission. Meta-analysis of multiple transmission experiments allowed us to establish a percent-metacyclic "cutoff" value that predicted transmission competence. Sand fly infections initiated with variable doses of parasites resulted in correspondingly altered percentages of metacyclic promastigotes, resulting in altered transmission frequency and disease severity. Lastly, alteration of sand fly oviposition status and environmental conditions at the time of transmission also influenced transmission frequency. These observations have implications for transmission of Leishmania by the sand fly vector in both the laboratory and in nature, including how the number of organisms acquired by the sand fly from an infection reservoir may influence the clinical outcome of infection following transmission by bite.

Measurements of Dune Parameters on Titan Suggest Differences in Sand Availability

Science.gov (United States)

Stewart, Brigitte W.; Radebaugh, Jani

2014-11-01

The equatorial region of Saturn’s moon Titan has five large sand seas with dunes similar to large linear dunes on Earth. Cassini Radar SAR swaths have high enough resolution (300 m) to measure dune parameters such as width and spacing, which helps inform us about formation conditions and long-term evolution of the sand dunes. Previous measurements in locations scattered across Titan have revealed an average width of 1.3 km and spacing of 2.7 km, with variations by location. We have taken over 1200 new measurements of dune width and spacing in the T8 swath, a region on the leading hemisphere of Titan in the Belet Sand Sea, between -5 and -9 degrees latitude. We have also taken over 500 measurements in the T44 swath, located on the anti-Saturn hemisphere in the Shangri-La Sand Sea, between 0 and 20 degrees latitude. We correlated each group of 50 measurements with the average distance from the edge of the dune field to obtain an estimate of how position within a dune field affects dune parameters. We found that in general, the width and spacing of dunes decreases with distance from the edge of the dune field, consistent with similar measurements in sand seas on Earth. We suggest that this correlation is due to the lesser availability of sand at the edges of dune fields. These measurements and correlations could be helpful in determining differences in sand availability across different dune fields, and along the entire equatorial region of Titan.

Laboratory studies of dune sand for the use of construction industry in Sri Lanka

Science.gov (United States)

de Silva Jayawardena, Upali; Wijesuriya, Roshan; Abayaweera, Gayan; Viduranga, Tharaka

2015-04-01

With the increase of the annual sand demand for the construction industry the excessive excavation of river sand is becoming a serious environmental problem in Sri Lanka. Therefore, it is necessary to explore the possibility for an alternative to stop or at least to minimize river sand mining activities. Dune sand is one of the available alternative materials to be considered instead of river sand in the country. Large quantities of sand dunes occur mainly along the NW and SE coastal belt which belong to very low rainfall Dry Zone coasts. The height of dune deposits, vary from 1m to about 30 meters above sea level. The objective of this paper is to indicate some studies and facts on the dune sand deposits of Sri Lanka. Laboratory studies were carried out for visual observations and physical properties at the initial stage and then a number of tests were carried out according to ASTM standards to obtain the compressive strength of concrete cylinders and mortar cubes mixing dune sand and river sand in different percentages keeping a constant water cement ratio. Next the water cement ratio was changed for constant dune sand and river sand proportion. Microscopic analysis shows that the dune sand consist of 95 % of quartz and 5 % of garnet, feldspar, illmenite and other heavy minerals with clay, fine dust, fine shell fragments and organic matters. Grains are sub-rounded to angular and tabular shapes. The grain sizes vary from fine to medium size of sand with silt. The degree of sorting and particle size observed with dune sands are more suited with the requirement of fine aggregates in the construction industry. The test result indicates that dune sand could be effectively used in construction work without sieving and it is ideal for wall plastering due to its'-uniformity. It could also be effectively used in concrete and in mortars mixing with river sand. The best mixing ratio is 75% dune sand and 25% river sand as the fine aggregate of concrete. For mortar the mixing

Galveston Island, Texas, Sand Management Strategies

Science.gov (United States)

2016-07-01

billion m3 of beach quality sand . However, Texas projects to date have not utilized these sources because of transportation costs. The lack of nearby...estimate that the San Luis Pass flood shoal contains approximately 11.8 million yd3 of beach quality sand . However, it is expected that if permits...a source of beach- quality sand . 2. Sand could be intercepted before it reaches the present dry beach. ERDC/CHL TR-16-13 55 3. The volume of

Numerical simulation of aeolian sand ripples

International Nuclear Information System (INIS)

Kang Liqiang; Guo Liejin

2004-01-01

With a new horizontal saltation displacement vector, a model is implemented to simulate the initiation and evolution of aeolian sand ripples. In the model, saltation distance considers the effects of surface height and slope. A linear stability analysis is also carried out for formation of sand ripples. The results show that, the model can be able to successfully reproduce sand ripples which can increase in scale by merging of small ripples. The linear stability analysis indicates that sand ripples appear when the relaxation rate parameter is below a threshold value and wind strength parameter is larger than a critical value. The results also verified that the formation of sand ripples is a self-organization process

Japan's involvement in oil sands development

International Nuclear Information System (INIS)

Sugiura, T.

1994-01-01

According to Japanese national policy, exploration and development by Japanese companies in overseas countries are promoted in order to ensure stable oil supplies. Japan Canada Oil Sands Limited (JACOS), part of the JAPEX group, was established during the 1978 world oil crisis to explore and develop Canadian oil sand resources in accordance with Japan's national policy. The JAPEX group, including JACOS, has invested $123 million in oil sands projects in Alberta. JAPEX's first involvement in oil sands was in the Primrose Project operated by Norcen in the Cold Lake area. Five years of cyclic steam stimulation pilot tests did not produce sufficiently good results to justify further operation. The second involvement was the PCEJ Project, a joint effort by four companies that are participating in a bitumen recovery test project in the Athabasca Deposit. JACOS holds 2,452 km 2 of oil sands leases in Alberta. Tests conducted since 1978 in the PCEJ Project include multiwell steam injection pilot tests, some of which showed promise. JACOS is also participating in steam assisted gravity drainage projects and in federal/provincial research programs. Obstacles identified in developing Alberta oil sands are the lack of a bitumen pipeline to Edmonton and the insufficient length of oil sands leases (currently 10 years), given the difficulties of oil sand development. 10 figs

MouldingSandDB – a modern database storing moulding sands properties research results

Directory of Open Access Journals (Sweden)

J. Jakubski

2011-01-01

Full Text Available The complexity of foundry processes requires the use of modern, advanced IT tools for optimization, storage and analysis of t echnicaldata. Properties of moulding and core sands that are collected in research laboratories, manufacturers, and finally in the foundries, are not in use later on. It seems important to create a database that will allow to use the results stored, along with the possibility of searching according to set criteria, adjusted to casting practice. This paper presents part of the database named „MouldingSandDB”, which allows to collect and search data for synthetic moulding sands.

Horizontal drilling in Miocene thin sand of Lake Maracaibo

Energy Technology Data Exchange (ETDEWEB)

Partidas, C. [PDVSA Exploration and Production (Venezuela)

1998-12-31

Horizontal drilling in the mature Lake Maracaibo field in Venezuela as a means of stimulating production are discussed. The Miocene sand where the horizontal well technology was applied, presented a number of intervals of unconsolidated sand of varied continuity, pay intervals at ten to twenty feet thickness, and reservoir pressures mostly at hydrostatic or below hydrostatic values. This paper evaluates a horizontal drilling program in the Lagunallis Lago Production Unit of Maracaibo, involving 91 wells to date (since 1995). When assessed in economic terms, results indicate that horizontal wells are a better economic alternative than vertical wells. The same results also showed that drainage from thin sand reservoirs resulted in better production with horizontal well technology than production from vertical wells. Payout was less than two years for 50 per cent of the horizontal wells while 40 per cent had payouts of between two and four years. Profit to investment ratio was greater than two in the case of about 70 per cent of the horizontal wells drilled in 1996. 2 tabs., 10 figs.

Residual diesel measurement in sand columns after surfactant/alcohol washing

International Nuclear Information System (INIS)

Martel, R.; Gelinas, P.J.

1996-01-01

A new simple gravimetric technique has been designed to determine residual oil saturation of complex hydrocarbon mixtures (e.g., diesel) in sand column experiments because reliable methods are lacking. The He/N 2 technique is based on drying of sand columns by circulating helium gas to drag oil droplets in a cold trap (liquid nitrogen). With this technique, residual diesel measurement can be performed easily immediately after alcohol/surfactant washing and in the same lab. For high residual diesel content in Ottawa sand (25 to 30 g/kg), the technique is much more accurate (± 2% or 600 mg/kg) than the standard analytical methods for the determination of mineral oil and grease. The average relative error on partial diesel dissolution in sand column estimated after alcohol/surfactant flooding (residual saturation of 10 to 15 g/kg) is as low as 5%. The precision of the He/N 2 technique is adequate to compare relative efficiency of washing solutions when partial extraction of residual oil in Ottawa sand columns is performed. However, this technique is not adapted for determination of traces of oil in sediment or for environmental control of contaminated soils. Each diesel determination by the He/N 2 technique costs less than $8 in chemical products (helium and liquid nitrogen). A simple laboratory drying setup can be built for less than $400 which makes this technique valuable for diesel analyses when a large number of tests are required

Policy Analysis of the Canadian Oil Sands Experience

Energy Technology Data Exchange (ETDEWEB)

None, None

2013-09-01

For those who support U.S. oil sands development, the Canadian oil sands industry is often identified as a model the U.S. might emulate, yielding financial and energy security benefits. For opponents of domestic oil sands development, the Canadian oil sands experience illustrates the risks that opponents of development believe should deter domestic policymakers from incenting U.S. oil sands development. This report does not seek to evaluate the particular underpinnings of either side of this policy argument, but rather attempts to delve into the question of whether the Canadian experience has relevance as a foundational model for U.S. oil sands development. More specifically, this report seeks to assess whether and how the Canadian oil sands experience might be predictive or instructive in the context of fashioning a framework for a U.S. oil sands industry. In evaluating the implications of these underpinnings for a prospective U.S. oil sands industry, this report concentrates on prospective development of the oil sands deposits found in Utah.

A study of global sand seas

Science.gov (United States)

McKee, Edwin D.

1979-01-01

The birth of the idea that led to this publication on "Global Sand Seas" dates back to the late 1920's. At that time I was engaged in a study of the Coconino Sandstone of Arizona's Grand Canyon. Considerable controversy existed then as to whether this sandstone was a subaqueous deposit or was composed of wind-formed dunes. It became apparent that definitive literature was sparse or lacking on types of dunes, global distribution of these types, the mechanics of their development, the precise nature of their internal structure of cross-stratificiation, and the relation of wind systems to these sand forms. Especially lacking were data on criteria that could confidently be used in the recognition of ancient dunes. The common denominator in this publication is eolian sand bodies. Although the book is concerned primarily with desert sand seas, the subject matter is not restricted to deserts; it includes many references to deposits of coastal sand and to sand bodies in humid climates. Nor does the book deal exclusively with dunes, which, according to most definitions, involve mounds or hills. Many references are made to sand sheets, sand stringers, and other types of sand deposits that have no prominent topographic expression. All sand bodies accumulated by the action of wind are discussed. Chapters A-J of this publication are primarily topical. Chapters cover the grain texture, the color, and the structure of modern dunes and other eolian sands. Special treatment is given to the relation of wind data to dune interpretation, the evolution of form in current-deposited sand bodies as determined from experimental studies, and the discriminant analysis technique for differentiating between coastal and inland desert sands. This topical part of the publication also includes an analysis of criteria used in ancient deposits to interpret their eolian genesis and a consideration of economic application of the principles described, including a discussion of potentials and problems

Bacteria of Phlebotominae Sand Flies Collected in Western Iran

Directory of Open Access Journals (Sweden)

Somayeh Rafatbakhsh-Iran

2015-08-01

Full Text Available Microorganisms particularly bacteria presenting in insects such as Phlebotominae may play an important role in the epidemiology of human infectious disease. Nowadays, because of vector implications, the routine methods of controlling and spraying have no more beneficial effects on vectors and reservoirs. Little knows about the prevalence and diversity of sand fly bacteria. The main objective of this study was to determine the presence of bacteria of phlebotominae sand flies collected in Hamadan, west of Iran. This information is important in order to development of vector control strategies. The microbial flora of Phlebotomus papatasi and P. sergenti the main vector of Cutaneous Leishmaniasis in the old world, were investigated. We characterized 8 bacteria, including 5 Gram-negative bacteria: Acinetobacter lwoffii, Pseudomonas aeruginosa, Enterobacter cloacae, Edvardsiela sp. and Proteus mirabilis and Gram-positive bacteria: Bacillus subtilis, Staphylococcus saprophyticus and Micrococcus luteus. Our study provides some data on the microbiota diversity of field-collected sand flies for the first time in Hamadan. Our results indicate that there is a range of variation of aerobic bacteria inhabiting sand fly, which possibly reflect the ecological condition of the habitat where the fly breeds. Microbiota is increasingly regarded as an important factor for modulating vector competence in insect vectors. So, mirobiota can be effects on the biology of phlebotominae and their roles in the sandfly-Leishmania interaction. Further experiments are required to clearly delineate the vectorial role of sand flies. Because it is probable that in the future, factors such as environmental changes, migration and urbanization can ease the transmission of leishmaniasis in this area.

The development of an integrated IT system at Albian Sands Energy

Energy Technology Data Exchange (ETDEWEB)

Michaud, L. H. [Albian Sands Energy Inc., Fort McMurray, AB (Canada)

2003-01-01

Factors considered in the selection, implementation and integration of computer applications in an oil sands surface mining and extraction operation are discussed. The company's objective in choosing the system was to optimize the use of information and to meet technical, business and information technology requirements. In a departure from typical practice where the system is selected by the information technology team, with minimal input from the technical and business units, in the case of Albian Sands Energy the company's technical and business people were closely involved in the selection process. Integration of the system was a primary consideration, including linking all applications through a data warehouse and electronic data management system. Details of the applications architecture, construction of the applications inventory, selection of the applications, identification of integration requirements, project management issues, and benefits of an integrated system are described. 6 refs., 2 tabs., 1 fig.

Numerical simulation of wind-sand movement in the reversed flow region of a sand dune with a bridge built downstream.

Science.gov (United States)

He, Wei; Huang, Ning; Xu, Bin; Wang, Wenbo

2018-04-23

A bridge built inside the reversed flow region of a sand dune will change the characteristics of wind-sand movement in this region. The Reynolds-averaged Navier-Stokes simulation and discrete particle tracing are used to simulate the wind-sand movement around a sand dune with a bridge built inside the reversed region. Three cases with different bridge positions are studied. The results show that 1) compared with the isolated dune case, a tall bridge built at the leeward toe leads to an increase in the deposition rate on the leeward slope and a longer reversed flow region downstream of the sand dune; meanwhile, the high speed of crosswind on the bridge indicates that some measures should be taken to protect trains from strong crosswind; 2) a low bridge at the leeward toe has little effect on the sand deposition and reversed flow region of the dune; however, low sand transport rate and crosswind speed on the bridge show that anti-crosswind/sand measures should be taken according to the actual situation and 3) a low bridge on the leeward slope has little effect on the length of reversed flow region, however, high crosswind speed and sand flux on the bridge reveal the need of anti-crosswind/sand measures on the bridge. Moreover, the bridges in the reversed flow region increase the sand flux near the leeward crest; as a result, the moving patterns of the sand dune are changed.

Sand dune tracking from satellite laser altimetry

Science.gov (United States)

Dabboor, Mohammed

Substantial problems arise from sand movement in arid and semi-arid countries. Sand poses a threat to infrastructure, agricultural and urban areas. These issues are caused by the encroachment of sand on roads and railway tracks, farmland, towns and villages, and airports, to name a few. Sand movement highly depends on geomorphology including vegetation cover, shape and height of the terrain, and grain size of the sand. However, wind direction and speed are the most important factors that affect efficient sand movement. The direction of the movement depends on the main direction of the wind, but it has been shown that a minimum wind speed is required, e.g. wind gusts, to initiate sand transport. This fact prevents a simple calculation of sand transport from conventional wind data as wind records rarely contain sub-minute intervals masking out any wind gusts. An alternative of predicting sand transport is the direct observation of sand advance by in situ measurements or via satellite. Until recently, satellite imagery was the only means to compare dune shape and position for predicting dune migration over several years. In 2003, the NASA laser altimetry mission ICESat became operational and monitors elevations over all surface types including sand dunes with an accuracy of about 10-20 cm. In this study, ICESat observations from repeat tracks (tracks overlapping eachother within 50 m) are used to derive sand dune advance and direction. The method employs a correlation of the elevation profiles over several dunes and was sucessfully validated with synthetic data. The accuracy of this method is 5 meters of dune advance. One of the most active areas exhibiting sand and dune movement is the area of the Arabian Peninsula. Approximately one-third of the Arabian Peninsula is covered by sand dunes. Different wind regimes (Shamal, Kaus) cause sand dune movement in the selected study area in the eastern part of the Arabian Peninsula between 20-25 degrees North and 45-55 degrees

An experimental study on pile spacing effects under lateral loading in sand.

Science.gov (United States)

Khari, Mahdy; Kassim, Khairul Anuar; Adnan, Azlan

2013-01-01

Grouped and single pile behavior differs owing to the impacts of the pile-to-pile interaction. Ultimate lateral resistance and lateral subgrade modulus within a pile group are known as the key parameters in the soil-pile interaction phenomenon. In this study, a series of experimental investigation was carried out on single and group pile subjected to monotonic lateral loadings. Experimental investigations were conducted on twelve model pile groups of configurations 1 × 2, 1 × 3, 2 × 2, 3 × 3, and 3 × 2 for embedded length-to-diameter ratio l/d = 32 into loose and dense sand, spacing from 3 to 6 pile diameter, in parallel and series arrangement. The tests were performed in dry sand from Johor Bahru, Malaysia. To reconstruct the sand samples, the new designed apparatus, Mobile Pluviator, was adopted. The ultimate lateral load is increased 53% in increasing of s/d from 3 to 6 owing to effects of sand relative density. An increasing of the number of piles in-group decreases the group efficiency owing to the increasing of overlapped stress zones and active wedges. A ratio of s/d more than 6d is large enough to eliminate the pile-to-pile interaction and the group effects. It may be more in the loose sand.

PANTAI PASIR PADI (PADDY SAND BEACH OF BANGKA ISLAND; CRABS (Scopimera sp POPULATION, FEEDING BEHAVIOUR AND THEIR BIRD PREDATOR

Directory of Open Access Journals (Sweden)

Hanifa Marisa

2016-11-01

Full Text Available An observation about beach crab (Scopimera sp population, their feeding behaviour and predator bird had been done at October 9 th, 2014 in Pantai Pasir Padi, Eastern Bangka Island beach, near Pangkal Pinang town. Ten 1 meter square plots were put at sandy beach and number of Scopimera sp be counted by the number of their hole nest home. Their feeding behaviour observed directly by eye-watching and video making. The threatening of bird predator was noted too.  The investigation find out that the mean of crabs population is 17 individu/m2 .  They come out from home hole for feeding around by sieving wet sand that be taken by front legs, obsorb organic nutrious material by mouth and kick residual sand to behind legs, move it as a small sand ball to right of left back side.  Production of small ball sand were about 15 - 30 balls /per minute. For making the nest hole, bigger sand ball were produced about 7 – 9 ball/minute; ball colour is same with under layer beach sand; quite grey. The crabs run instinctivey fast, when the threat come from their natural enemy, predator bird, Actitis hypoleucos.  Bird searching behaviour look adapted to the fast run of crab. Keywords: Scopimera sp, Actitis hypoleucos, small sand ball, predator, behaviour

33 CFR 181.27 - Information displayed near hull identification number.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Information displayed near hull... displayed near hull identification number. With the exception of the characters “US-”, which constitute the... the 12-character hull identification number (HIN), that information must be separated from the HIN by...

Effect of bioremediation agents on oil biodegradation in medium-fine sand

International Nuclear Information System (INIS)

Croft, B.C.; Swannell, R.P.J.; Grant, A.L.; Lee, K.

1995-01-01

A spill of weathered Arabian light crude oil on an intertidal sand zone was simulated in the laboratory. Respirometry, chemical, and microbiological methods were employed to assess the effectiveness of two bioremediation agents: a slow-release inorganic (Max Bac) and an oleophilic organic fertilizer (Inipol EAP22). Inipol EAP22 stimulated additional CO 2 evolution, and significantly increased both the total chemoheterotrophic population and the number of hydrocarbon-degrading microorganisms. At the end of the experiment, the residual oil extracted from the Inipol-treated sand was significantly more biodegraded, based on the application of the conserved biomarkers (phytane and 17α, 21β hopane), than that removed from the other sand columns, albeit by a relatively small amount. The results suggested that Inipol EAP22 stimulated the chemoheterotrophic and hydrocarbon-degrading microbial population and, after a lag phase, encouraged oil biodegradation in fine sandy sediments subjected to a vertical tidal cycle

Feeding preferences of Lutzomyia longipalpis (Diptera: Psychodidae), the sand fly vector, for Leishmania infantum (Kinetoplastida: Trypanosomatidae).

Science.gov (United States)

Macedo-Silva, Virgínia P; Martins, Daniella R A; De Queiroz, Paula Vivianne Souza; Pinheiro, Marcos Paulo G; Freire, Caio C M; Queiroz, José W; Dupnik, Kathryn M; Pearson, Richard D; Wilson, Mary E; Jeronimo, Selma M B; Ximenes, Maria De Fátima F M

2014-01-01

Leishmania infantum, the causative agent of visceral leishmaniasis (VL) in Brazil, is spread mostly by the bite of the sand fly Lutzomyia longipalpis (Lutz & Neiva). We trapped sand flies in endemic neighborhoods near Natal, Brazil, where cases of human and dog VL were documented. Amplification of species-specific cytochrome b (Cyt b) genes by polymerase chain reaction revealed that sand flies from rural and periurban areas harbored blood from different sources. The most common source ofbloodmeal was human, but blood from dog, chicken, and armadillo was also present. We tested the preference for a source of bloodmeal experimentally by feeding L. longipalpis F1 with blood from different animals. There were significant differences between the proportion of flies engorged and number of eggs laid among flies fed on different sources, varying from 8.4 to 19 (P < 0.0001). Blood from guinea pig or horse was best to support sand fly oviposition, but human blood also supported sand fly oviposition well. No sand flies fed on cats, and sand flies feeding on the opossum Monodelphis domestica Wagner produced no eggs. These data support the hypothesis that L. longipalpis is an eclectic feeder, and humans are an important source of blood for this sand fly species in periurban areas of Brazil.

Classification of sand samples according to radioactivity content by the use of euclidean and rough sets techniques

International Nuclear Information System (INIS)

Abd El-Monsef, M.M.; Kozae, A.M.; Seddeek, M.K.; Medhat, T.; Sharshar, T.; Badran, H.M.

2004-01-01

Form the geological point of view, the origin and transport of black and normal sands is particularly important. Black and normal sands came to their places along the Mediterranean-sea coast after transport by some natural process. Both types of sands have different radiological properties. This study is, therefore, attempts to use mathematical methods to classify Egyptian sand samples collected from 42 locations in an area of 40 x 19 km 2 based on their radioactivity contents. The use of all information resulted from the experimental measurements of radioactivity contents as well as some other parameters can be a time and effort consuming task. So that the process of eliminating unnecessary attributes is of prime importance. This elimination process of the superfluous attributes that cannot affect the decision was carried out. Some topological techniques to classify the information systems resulting from the radioactivity measurements were then carried out. These techniques were applied in Euclidean and quasi-discrete topological cases. While there are some applications in environmental radioactivity of the former case, the use of the quasi-discrete in the so-called rough set information analysis is new in such a study. The mathematical methods are summarized and the results and their radiological implications are discussed. Generally, the results indicate no radiological anomaly and it supports the hypothesis previously suggested about the presence of two types of sand in the studied area

White Sands Missile Range 2011 Drinking Water Quality Report

Science.gov (United States)

2012-01-01

acerca de su agua potable . Haga que alguien lo traduzca para usted, o hable con alguien que lo entienda. Main Post White Sands Missile Range 2011...standards. What is This Water Quality Report? Este informe contiene informacion importante acerca de su agua potable . Haga que alguien lo traduzca

bentonite-sand mixture as new backfill/buffer material

International Nuclear Information System (INIS)

Cui Suli; Liu Jisheng; Zhang Huyuan; Liang Jian

2008-01-01

The mixture of bentonite and quartz sand is suggested as a new backfill/buffer material for geological disposal of HLW. To improve the further design of underground laboratory and in-situ industrial construction test, the optimization of sand addition to bentonite is focused at present research stage. Based on summarizing the research results abroad, laboratory tests were conducted on the mixture of GMZ001 bentonite and quartz sand, such as compaction test and swelling tests etc. Test data shows that GMZ bentonite-sand mixture exhibits a favorite compaction with a 30% sand addition, a highest swelling pressure with a 20% sand addition, and a decreasing plasticity with increases in sand addition and pore liquid concentration. (authors)

Comparison between predicted and observed sand waves and sand banks in the North Sea

NARCIS (Netherlands)

Hulscher, Suzanne J.M.H.; van den Brink, G.M.

2001-01-01

For the first time a prediction model of regular morphological patterns on the seabed was tested against observations of sand wave and sand bank occurrence in the entire North Sea. The model, which originates from first physical principles, predicts this occurrence via two dimensionless parameters

EFFECTIVENESS OF THE SANDPITS SECURITY SYSTEM AGAINST MICROORGANISMS AND INTESTINAL PARASITES SAND CONTAMINATION

Directory of Open Access Journals (Sweden)

Magdalena Błaszak

2015-09-01

Full Text Available Playgrounds and sandpits (small architecture objects according to the Construction Law are subject to meticulous supervision, both at the design stage and subsequent status checks of the objects. One of the requirements arising from the need to protect playgrounds from animals is the necessity for fencing the object (Regulation of 31 December 2002 On Safety and Hygiene in Public and Private Schools and Institutions; Polish Standard PN-EN 1176 Playground equipment and surfacing. Does fencing playgrounds really reduce contamination of sand? To verify this hypothesis, the studies have been conducted on the residential areas’ sandpits, both fence secured and unsecured, located in close proximity to one another. The aim of the study was to evaluate the effectiveness of fences and nets as protection from microbial and parasite contamination of sandpits, mainly due to the access of animals to them. For several seasons of spring and summer the sand was examined in terms of the total number of heterotrophic bacteria and fungi (organic matter contamination of sand indicators and for the presence of coliform bacteria (including Escherichia coli, bacteria of the Salmonella genus and the eggs of intestinal parasites. It can be concluded that fencing playgrounds affects sand pollution less with waste and plant material (as a consequence, it has been reported statistically significantly less heterotrophic bacteria and fungi in the fenced sandpits’ sand. Unfortunately, the fence does not eliminate the risks associated with sand pollution of coliform bacteria. Cats and birds, but also dogs, still have a continuous access to sand. Due to the repeatedly stated carelessness of children and their caregivers, gates left open to the playground do not constitute an obstacle for domestic and stray animals. Another source of sand pollution with intestinal pathogens can be a manner of carriage of new sand, as there is no legislation governing the issue of transport

Critical State of Sand Matrix Soils

Science.gov (United States)

Marto, Aminaton; Tan, Choy Soon; Makhtar, Ahmad Mahir; Kung Leong, Tiong

2014-01-01

The Critical State Soil Mechanic (CSSM) is a globally recognised framework while the critical states for sand and clay are both well established. Nevertheless, the development of the critical state of sand matrix soils is lacking. This paper discusses the development of critical state lines and corresponding critical state parameters for the investigated material, sand matrix soils using sand-kaolin mixtures. The output of this paper can be used as an interpretation framework for the research on liquefaction susceptibility of sand matrix soils in the future. The strain controlled triaxial test apparatus was used to provide the monotonic loading onto the reconstituted soil specimens. All tested soils were subjected to isotropic consolidation and sheared under undrained condition until critical state was ascertain. Based on the results of 32 test specimens, the critical state lines for eight different sand matrix soils were developed together with the corresponding values of critical state parameters, M, λ, and Γ. The range of the value of M, λ, and Γ is 0.803–0.998, 0.144–0.248, and 1.727–2.279, respectively. These values are comparable to the critical state parameters of river sand and kaolin clay. However, the relationship between fines percentages and these critical state parameters is too scattered to be correlated. PMID:24757417

The jammed-to-mobile transition in frozen sand under stress

Science.gov (United States)

Durham, W. B.; Pathare, A.; Stern, L. A.; Lenferink, H. J.

2009-12-01

We conducted laboratory deformation experiments on sand-rich mixtures of sand + ice under sufficient confinement to inhibit macroscopic dilation. Dry sand packs constrained not to dilate when they are under a shearing load reach an immobile or “jammed” state, as load-supporting “force chains” of sand particles form after a small amount of strain and cannot be broken without volume expansion. Our research objective here was to find the minimum volume fraction of ice required to overcome the jammed state. The result surprised us: the required volume fraction is not a fixed number, but depends on the packing characteristics of the sand in question. Experiments were carried out in a triaxial gas deformation rig at confining pressures (60 - 200 MPa) always at least twice the level of differential stresses (11 - 50 MPa) in order to suppress dilatancy. Run temperatures were 223 - 243 K. We used two kinds of quartz sand, one well-sorted, with a maximum dry packing density (MDPD) of about 0.68 sand by volume, and the other a mixture of two sizes, having a higher MDPD of 0.75. Ice volume fraction ranged from well below saturation (where unfilled porosity necessarily remained) to slightly greater than the value of porosity at MDPD. We tested these frozen sands in compression under constant applied differential stress (creep). Strain rates were very low at these conditions, and runs took days or weeks to complete. The amount of strain required to reach the jammed state in ice-undersaturated samples was approximately 0.04, and did not show an obvious dependence on ice content. For both sands, the onset of mobility occurred at approximately 5% above the value of pore volume at MDPD. Furthermore, viscosity of mobile frozen sand near the transition point was extremely sensitive to ice fraction, which implies that at geologic strain rates, far slower than we can reach in the lab, the ice fraction at transition may lie closer to that at MDPD. Cryogenic scanning electron

Heavy crude and tar sands - the long-term oil reserve

Energy Technology Data Exchange (ETDEWEB)

Barnea, J

1984-10-01

It appears that heavy crude and tar sands occur in many sedimentary areas, and estimates of known world-wide quantities exceed those known for conventional light crude resources. Although there are not precise figures available, production could be as high as three million barrels per day, with Venezuela, the US, and Canada the largest producers. There are different scales to measure the costs of production because of differences in the quality of various types of heavy crude and tar sands. Economic development of these resources should banish fears of oil scarcity in the foreseeable future. A center for information exchange through international meetings and publications is under development.

Production and global transport of Titan's sand particles

Science.gov (United States)

Barnes, Jason W.; Lorenz, Ralph D.; Radebaugh, Jani; Hayes, Alexander G.; Arnold, Karl; Chandler, Clayton

2015-06-01

Previous authors have suggested that Titan's individual sand particles form by either sintering or by lithification and erosion. We suggest two new mechanisms for the production of Titan's organic sand particles that would occur within bodies of liquid: flocculation and evaporitic precipitation. Such production mechanisms would suggest discrete sand sources in dry lakebeds. We search for such sources, but find no convincing candidates with the present Cassini Visual and Infrared Mapping Spectrometer coverage. As a result we propose that Titan's equatorial dunes may represent a single, global sand sea with west-to-east transport providing sources and sinks for sand in each interconnected basin. The sand might then be transported around Xanadu by fast-moving Barchan dune chains and/or fluvial transport in transient riverbeds. A river at the Xanadu/Shangri-La border could explain the sharp edge of the sand sea there, much like the Kuiseb River stops the Namib Sand Sea in southwest Africa on Earth. Future missions could use the composition of Titan's sands to constrain the global hydrocarbon cycle.

High temperature thermal energy storage in moving sand

Science.gov (United States)

Turner, R. H.; Awaya, H. I.

1978-01-01

Several high-temperature (to 500 C) heat-storage systems using sand as the storage medium are described. The advantages of sand as a storage medium include low cost for sand, widespread availability, non-toxicity, non-degradation characteristics, easy containment, and safety. The systems considered include: stationary sand with closely spaced tubes throughout the volume, the use of a fluidized bed, use of conveyor belt transporter, and the use of a blower rapid transport system. For a stationary sand bed, very close spacing of heat transfer tubes throughout the volume is required, manifesting as high power related system cost. The suggestion of moving sand past or around pipes is intended to reduce the power related costs at the penalty of added system complexity. Preliminary system cost estimates are offered. These rough calculations indicate that mobile sand heat storage systems cost less than the stationary sand approach.

Sand to Root Transfer of PAHs and PCBs by Carrots Grown on Sand with Pure Substances and Biosolids Amended Sand

OpenAIRE

Sablayrolles, Caroline; Montréjaud-Vignoles, Mireille; Silvestre, Jérôme; Patria, Lucie

2006-01-01

A study on behaviour of trace organic compounds (Polycyclic Aromatic Hydrocarbons, PAH, and Polychlorinated Biphenyls, PCB) in a sand-plant system has been carried out, with the reclamation of wastewater treatment plant biosolids for agriculture in mind. Carrot plants (Daucus carota) were grown on soilless culture (sand), to provide optimal transfer conditions, in plant containers inside a temperature regulated greenhouse. There were two types of experiment. The trace organic compounds have i...

Centennial review-forecast--oil sands, shales spar for markets

Energy Technology Data Exchange (ETDEWEB)

Pamenter, C B

1967-09-01

The relationship between possible developments of tar sands and oil shale deposits to the future of the oil and gas industry is examined. The Athabasca tar sands are estimated to contain 85 billion bbl of synthetic crude oil which can be exploited using currently available mining equipment and proven techniques. Another 240 billion bbl of synthetic crude are potentially available through in-situ extraction methods. Great Canadian Oil Sands Ltd. is using an extraction procedure which involves a surface mining operation, extraction and processing of the bitumen, and product shipments via a 266-mile pipeline. This procedure will be used to produce 45,000 bpd of synthetic crude and 300 ton per day of sulfur. Syncrude Canada Ltd. and Shell Canada Ltd. both have applied to the Alberta government for permission to operate 100,000-bpd operations. Syncrudes is a mining operation and Shell plans to use in-situ extraction. A number of companies have conducted research projects concerning shale oil recovery. The majority of these projects have been aimed at improving mining operations. In-situ retorting of kerogen and extraction of oil has also received consideration.

Water Quality, Weather and Environmental Factors Associated with Fecal Indicator Organism Density in Beach Sand at Two Recreational Marine Beaches

Science.gov (United States)

Recent studies showing an association between fecal indicator organisms (FIOs and gastrointestinal (GI) illness among beachgoers wit sand contact have important public health implicatons because of the large numbers of people who recreate at beaches and engage in sand contact act...

Gases Emission From Surface Layers of Sand Moulds and Cores Stored Under the Humid Air Conditions

Directory of Open Access Journals (Sweden)

Kaźnica N.

2017-12-01

Full Text Available A large number of defects of castings made in sand moulds is caused by gases. There are several sources of gases: gases emitted from moulds, cores or protective coatings during pouring and casting solidification; water in moulding sands; moisture adsorbed from surroundings due to atmospheric conditions changes. In investigations of gas volumetric emissions of moulding sands amounts of gases emitted from moulding sand were determined - up to now - in dependence of the applied binders, sand grains, protective coatings or alloys used for moulds pouring. The results of investigating gas volumetric emissions of thin-walled sand cores poured with liquid metal are presented in the hereby paper. They correspond to the surface layer in the mould work part, which is decisive for the surface quality of the obtained castings. In addition, cores were stored under conditions of a high air humidity, where due to large differences in humidity, the moisture - from surroundings - was adsorbed into the surface layer of the sand mould. Due to that, it was possible to asses the influence of the adsorbed moisture on the gas volumetric emission from moulds and cores surface layers by means of the new method of investigating the gas emission kinetics from thin moulding sand layers heated by liquid metal. The results of investigations of kinetics of the gas emission from moulding sands with furan and alkyd resins as well as with hydrated sodium silicate (water glass are presented. Kinetics of gases emissions from these kinds of moulding sands poured with Al-Si alloy were compared.

Analysis of wind-blown sand movement over transverse dunes.

Science.gov (United States)

Jiang, Hong; Huang, Ning; Zhu, Yuanjian

2014-12-01

Wind-blown sand movement often occurs in a very complicated desert environment where sand dunes and ripples are the basic forms. However, most current studies on the theoretic and numerical models of wind-blown sand movement only consider ideal conditions such as steady wind velocity, flat sand surface, etc. In fact, the windward slope gradient plays a great role in the lift-off and sand particle saltation. In this paper, we propose a numerical model for the coupling effect between wind flow and saltating sand particles to simulate wind-blown sand movement over the slope surface and use the SIMPLE algorithm to calculate wind flow and simulate sands transport by tracking sand particle trajectories. We furthermore compare the result of numerical simulation with wind tunnel experiments. These results prove that sand particles have obvious effect on wind flow, especially that over the leeward slope. This study is a preliminary study on windblown sand movement in a complex terrain, and is of significance in the control of dust storms and land desertification.

Sand Fly Fauna (Diptera, Pcychodidae, Phlebotominae) in Different Leishmaniasis-Endemic Areas of Ecuador, Surveyed Using a Newly Named Mini-Shannon Trap

Science.gov (United States)

Hashiguchi, Kazue; Velez N., Lenin; Kato, Hirotomo; Criollo F., Hipatia; Romero A., Daniel; Gomez L., Eduardo; Martini R., Luiggi; Zambrano C., Flavio; Calvopina H., Manuel; Caceres G., Abraham; Hashiguchi, Yoshihisa

2014-01-01

To study the sand fly fauna, surveys were performed at four different leishmaniasis-endemic sites in Ecuador from February 2013 to April 2014. A modified and simplified version of the conventional Shannon trap was named “mini-Shannon trap” and put to multiple uses at the different study sites in limited, forested and narrow spaces. The mini-Shannon, CDC light trap and protected human landing method were employed for sand fly collection. The species identification of sand flies was performed mainly based on the morphology of spermathecae and cibarium, after dissection of fresh samples. In this study, therefore, only female samples were used for analysis. A total of 1,480 female sand flies belonging to 25 Lutzomyia species were collected. The number of female sand flies collected was 417 (28.2%) using the mini-Shannon trap, 259 (17.5%) using the CDC light trap and 804 (54.3%) by human landing. The total number of sand flies per trap collected by the different methods was markedly affected by the study site, probably because of the various composition of species at each locality. Furthermore, as an additional study, the attraction of sand flies to mini-Shannon traps powered with LED white-light and LED black-light was investigated preliminarily, together with the CDC light trap and human landing. As a result, a total of 426 sand flies of nine Lutzomyia species, including seven man-biting and two non-biting species, were collected during three capture trials in May and June 2014 in an area endemic for leishmaniasis (La Ventura). The black-light proved relatively superior to the white-light with regard to capture numbers, but no significant statistical difference was observed between the two traps. PMID:25589880

Sand consolidation

Energy Technology Data Exchange (ETDEWEB)

Spain, H H

1965-01-21

In a sand consolidation method in which there is injected a mixture of resin-forming liquids comprising an aryl-hydroxy low molecular weight compound, a water- soluble aldehyde, and a catalyst, an improvement is claimed which comprises diluting the resin-forming liquids with a diluent and with water so that the yield of the resin is sufficient to consolidate the sand particles with the minimum desirable pressure. The diluent may be mutually soluble in water and in the resin-forming liquids, and does not affect the setting time of the polymer. The aldehyde and the aryl-hydroxy compound may be in ratio of 5:1, and the diluent, methyl alcohol, is present in a ratio of 2:1 with reference to the water.

An Experimental Study on Pile Spacing Effects under Lateral Loading in Sand

Science.gov (United States)

Khari, Mahdy; Kassim, Khairul Anuar; Adnan, Azlan

2013-01-01

Grouped and single pile behavior differs owing to the impacts of the pile-to-pile interaction. Ultimate lateral resistance and lateral subgrade modulus within a pile group are known as the key parameters in the soil-pile interaction phenomenon. In this study, a series of experimental investigation was carried out on single and group pile subjected to monotonic lateral loadings. Experimental investigations were conducted on twelve model pile groups of configurations 1 × 2, 1 × 3, 2 × 2, 3 × 3, and 3 × 2 for embedded length-to-diameter ratio l/d = 32 into loose and dense sand, spacing from 3 to 6 pile diameter, in parallel and series arrangement. The tests were performed in dry sand from Johor Bahru, Malaysia. To reconstruct the sand samples, the new designed apparatus, Mobile Pluviator, was adopted. The ultimate lateral load is increased 53% in increasing of s/d from 3 to 6 owing to effects of sand relative density. An increasing of the number of piles in-group decreases the group efficiency owing to the increasing of overlapped stress zones and active wedges. A ratio of s/d more than 6d is large enough to eliminate the pile-to-pile interaction and the group effects. It may be more in the loose sand. PMID:24453900

Sands at Gusev Crater, Mars

Science.gov (United States)

Cabrol, Nathalie A.; Herkenhoff, Kenneth E.; Knoll, Andrew H.; Farmer, Jack D.; Arvidson, Raymond E.; Grin, E.A.; Li, Ron; Fenton, Lori; Cohen, B.; Bell, J.F.; Yingst, R. Aileen

2014-01-01

Processes, environments, and the energy associated with the transport and deposition of sand at Gusev Crater are characterized at the microscopic scale through the comparison of statistical moments for particle size and shape distributions. Bivariate and factor analyses define distinct textural groups at 51 sites along the traverse completed by the Spirit rover as it crossed the plains and went into the Columbia Hills. Fine-to-medium sand is ubiquitous in ripples and wind drifts. Most distributions show excess fine material, consistent with a predominance of wind erosion over the last 3.8 billion years. Negative skewness at West Valley is explained by the removal of fine sand during active erosion, or alternatively, by excess accumulation of coarse sand from a local source. The coarse to very coarse sand particles of ripple armors in the basaltic plains have a unique combination of size and shape. Their distribution display significant changes in their statistical moments within the ~400 m that separate the Columbia Memorial Station from Bonneville Crater. Results are consistent with aeolian and/or impact deposition, while the elongated and rounded shape of the grains forming the ripples, as well as their direction of origin, could point to Ma'adim Vallis as a possible source. For smaller particles on the traverse, our findings confirm that aeolian processes have dominated over impact and other processes to produce sands with the observed size and shape patterns across a spectrum of geologic (e.g., ripples and plains soils) and aerographic settings (e.g., wind shadows).

Pullout capacity of batter pile in sand.

Science.gov (United States)

Nazir, Ashraf; Nasr, Ahmed

2013-03-01

Many offshore structures are subjected to overturning moments due to wind load, wave pressure, and ship impacts. Also most of retaining walls are subjected to horizontal forces and bending moments, these forces are due to earth pressure. For foundations in such structures, usually a combination of vertical and batter piles is used. Little information is available in the literature about estimating the capacity of piles under uplift. In cases where these supporting piles are not vertical, the behavior under axial pullout is not well established. In order to delineate the significant variables affecting the ultimate uplift shaft resistance of batter pile in dry sand, a testing program comprising 62 pullout tests was conducted. The tests are conducted on model steel pile installed in loose, medium, and dense sand to an embedded depth ratio, L/d, vary from 7.5 to 30 and with various batter angles of 0°, 10°, 20°, and 30°. Results indicate that the pullout capacity of a batter pile constructed in dense and/or medium density sand increases with the increase of batter angle attains maximum value and then decreases, the maximum value of Pα occurs at batter angle approximately equal to 20°, and it is about 21-31% more than the vertical pile capacity, while the pullout capacity for batter pile that constructed in loose sand decreases with the increase of pile inclination. The results also indicated that the circular pile is more resistant to pullout forces than the square and rectangular pile shape. The rough model piles tested is experienced 18-75% increase in capacity compared with the smooth model piles. The suggested relations for the pullout capacity of batter pile regarding the vertical pile capacity are well predicted.

Pullout capacity of batter pile in sand

Directory of Open Access Journals (Sweden)

Ashraf Nazir

2013-03-01

Full Text Available Many offshore structures are subjected to overturning moments due to wind load, wave pressure, and ship impacts. Also most of retaining walls are subjected to horizontal forces and bending moments, these forces are due to earth pressure. For foundations in such structures, usually a combination of vertical and batter piles is used. Little information is available in the literature about estimating the capacity of piles under uplift. In cases where these supporting piles are not vertical, the behavior under axial pullout is not well established. In order to delineate the significant variables affecting the ultimate uplift shaft resistance of batter pile in dry sand, a testing program comprising 62 pullout tests was conducted. The tests are conducted on model steel pile installed in loose, medium, and dense sand to an embedded depth ratio, L/d, vary from 7.5 to 30 and with various batter angles of 0°, 10°, 20°, and 30°. Results indicate that the pullout capacity of a batter pile constructed in dense and/or medium density sand increases with the increase of batter angle attains maximum value and then decreases, the maximum value of Pα occurs at batter angle approximately equal to 20°, and it is about 21–31% more than the vertical pile capacity, while the pullout capacity for batter pile that constructed in loose sand decreases with the increase of pile inclination. The results also indicated that the circular pile is more resistant to pullout forces than the square and rectangular pile shape. The rough model piles tested is experienced 18–75% increase in capacity compared with the smooth model piles. The suggested relations for the pullout capacity of batter pile regarding the vertical pile capacity are well predicted.

Direct Chlorination of Zircon Sand

International Nuclear Information System (INIS)

Dwiretnani Sudjoko; Budi Sulistyo; Pristi Hartati; Sunardjo

2002-01-01

It was investigated the direct chlorination of zircon sand in a unit chlorination equipment. The process was in semi batch. The product gas was scrubbed in aqueous NaOH. It was search the influence of time, ratio of reactant and size of particle sand to the concentration of Zr and Si in the product. From these research it was found that as the times, ratio of reactant increased, the concentration of Zr increased, but the concentration of Si decreased, while as grain size of zircon sand decreased the concentration of Zr decreased, but the concentration of Si increased. (author)

Expectations and drivers of future greenhouse gas emissions from Canada's oil sands: An expert elicitation

International Nuclear Information System (INIS)

McKellar, Jennifer M.; Sleep, Sylvia; Bergerson, Joule A.; MacLean, Heather L.

2017-01-01

The greenhouse gas (GHG) emissions intensity of oil sands operations has declined over time but has not offset absolute emissions growth due to rapidly increasing production. Policy making, decisions about research and development, and stakeholder discourse should be informed by an assessment of future emissions intensity trends, however informed projections are not easily generated. This study investigates expected trends in oil sands GHG emissions using expert elicitation. Thirteen experts participated in a survey, providing quantitative estimates of expected GHG emissions intensity changes and qualitative identifications of drivers. Experts generally agree that emissions intensity reductions are expected at commercially operating projects by 2033, with the greatest reductions expected through the use of technology in the in situ area of oil sands activity (40% mean reduction at multiple projects, averaged across experts). Incremental process changes are expected to contribute less to reducing GHG emissions intensity, however their potentially lower risk and cost may result in larger cumulative reductions. Both technology availability and more stringent GHG mitigation policies are required to realize these emissions intensity reductions. This paper demonstrates a method to increase rigour in emissions forecasting activities and the results can inform policy making, research and development and modelling and forecasting studies. - Highlights: • Expert elicitation used to investigate expected trends in oil sands GHG emissions. • Overall, emissions intensity reductions are expected at commercial projects by 2033. • Reductions are expected due to both technology changes and process improvements. • Technology availability and more stringent GHG policies are needed for reductions. • Method used increases rigour in emissions forecasting, and results inform policy.

Performance of a sand filter in removal of micro-algae from seawater in aquaculture production systems.

Science.gov (United States)

Sabiri, N E; Castaing, J B; Massé, A; Jaouen, P

2012-01-01

In this study, a sand filter was used to remove micro-algae from seawater feeding aquaculture ponds. A lab-scale sand filter was used to filter 30,000 cells/mL of Heterocapsa triquetra suspension, a non-toxic micro-alga that has morphological and dimensional (15-20 microm) similarities with Alexandrium sp., one of the smallest toxic micro-algae in seawater. Removal efficiency and capture mechanisms for a fixed superficial velocity (3.5 m/h) were evaluated in relation to size distribution and mean diameter of the sand. Various sands (average diameter ranging between 200 microm and 600 microm) were characterized and used as porous media. The structural parameters of the fixed beds were evaluated for each medium using experimental measurements of pressure drop as a function of superficial velocity over a range of Reynolds numbers covering Darcy's regime and the inertial regime. For a filtration cycle of six hours, the best efficiency (E = 90%) was obtained with the following sand characteristics: sieved sand with a range of grain diameter of 100 and 300 microm and a mean grain diameter equal to 256 microm. Results obtained show the influence of the size distribution of sand on the quality of retention of the micro-algae studied.

Energy information data base: report number codes

Energy Technology Data Exchange (ETDEWEB)

None

1979-09-01

Each report processed by the US DOE Technical Information Center is identified by a unique report number consisting of a code plus a sequential number. In most cases, the code identifies the originating installation. In some cases, it identifies a specific program or a type of publication. Listed in this publication are all codes that have been used by DOE in cataloging reports. This compilation consists of two parts. Part I is an alphabetical listing of report codes identified with the issuing installations that have used the codes. Part II is an alphabetical listing of installations identified with codes each has used. (RWR)

Energy information data base: report number codes

International Nuclear Information System (INIS)

1979-09-01

Each report processed by the US DOE Technical Information Center is identified by a unique report number consisting of a code plus a sequential number. In most cases, the code identifies the originating installation. In some cases, it identifies a specific program or a type of publication. Listed in this publication are all codes that have been used by DOE in cataloging reports. This compilation consists of two parts. Part I is an alphabetical listing of report codes identified with the issuing installations that have used the codes. Part II is an alphabetical listing of installations identified with codes each has used

Thermal Conductivity of Polymer Composite poypropilene-Sand

International Nuclear Information System (INIS)

Betha; Mashuri; Sudirman; Karo Karo, Aloma

2001-01-01

Thermal conductivity composite materials polypropylene (PP)-sand have been investigated. PP composite with sand to increase thermal conductivity from the polymer. The composite in this observation is done by mixing matrix (PP melt flow 2/10)and filler sand)by means tool labo plastomil. The result of thermal conductivity is composite of PP-sand which is obtained increase and followed by the raising of filler particle volume fraction. The analysis of thermal conductivity based on the model Cheng and Vachon, model Lewis and Nielsen where this model has the function to support experiment finding. It is proved that Lewis' and Nielsen's model almost approach experiment result. And then thermal conductivity raising will be analyzed by the model of pararel-series conductive with the two (2)phases system. It is showed that sand in PP MF 2 composite have the big role to increase the thermal conductivity than sand in PP MF 10 composition, but it is not easy to shape conductive medium

Final report on Thermally Modified Sand demonstration project

Energy Technology Data Exchange (ETDEWEB)

1994-09-23

The use of salt and salt/sand mixtures on icy roadway surfaces has dramatically increased during the past 30 years. Despite extensive documentation on salt related damage to the roadway improvements, vehicles and the environment, road maintenance departments have continued to rely on this practice. Road maintenance departments in northern climate areas have long recognized the safety benefits for public mobility on icy roadways from the use of sand. As an abrasive material, the sand improves the surface traction that results in more drivable and less hazardous road conditions during the winter months. Stockpiles of pure sand stored during the winter months oftentimes freeze into large unworkable, monolithic piles. To maintain a free-flowing condition, it has been found to be necessary to add salt to the sand. The addition of salt in amounts ranging from 5 to 10 percent to that of sand, is usually sufficient to provide relatively free-flowing abrasive material that could be stored in stockpiles and applied to icy road surfaces with conventional sand spreading trucks. Another alternative for winter storage of pure sand to maintain a free-flowing condition is in humidity-controlled, heated buildings. As would be expected, this method has high capital and operating costs. and not cost effective for general highway maintenance use. The invention demonstrated herein is a method of thermally modifying pure sand that will remain in a free-flowing state throughout the winter season without the need for the salt additive. The thermally modified sand provides an abrasive material that when applied to icy roads does not cause environmental and corrosive damage as done by the application of sand with salt. By employing a very simple process of freezing screened sand particles by forced air convection under subfreezing conditions, the invention creates a product that has significant value in terms of economic and environmental benefits.

Evaluate of head loss, sediment value and copper removal in sand media (rapid sand filter

Directory of Open Access Journals (Sweden)

Daneshi Navab

2014-06-01

Full Text Available Along with the technology development and increasing consumption of water resources, we are experiencing low qualities in the mentioned resources. Copper brings about serious environment al pollution, threatening human health and ecosystem. This metal found variously in water resources and industrial activities. Therefore, it needs to treat the water resources from these excessive amounts. Different methods have used for this reason but the most used method during recent years has been the absorption by economic absorbers such as sand. Rapid sand filters usually used in water and wastewater treatment plants for water clarification. In this research, a single layer gravity rapid sand filter has used to reduce different concentrations of copper. sediment value and head loss arising in filter media is simulated by using combination of Carman-Kozeny, Rose and Gregory models in different discharges of rapid sand filter. Results have shown that with increasing in discharge and decreasing in input copper concentration, arriving time to given head loss, is increasing. In addition, results demonstrated that with increasing in copper concentration in influent, removal efficiency is decreasing somewhat. Results of this research can applied in an appropriate design of rapid sand filter to copper removal, a prediction of rapid sand filter ability to copper removal and an estimation of arising head loss during filter work thus evaluating of time interval backwash. DOI: http://dx.doi.org/10.3126/ije.v3i2.10641 International Journal of the Environment Vol.3(2 2014: 276-286

In situ recovery of oil from Utah tar sand: a summary of tar sand research at the Laramie Energy Technology Center

Energy Technology Data Exchange (ETDEWEB)

Marchant, L.C.; Westhoff, J.D.

1985-10-01

This report describes work done by the United States Department of Energy's Laramie Energy Technology Center from 1971 through 1982 to develop technology for future recovery of oil from US tar sands. Work was concentrated on major US tar sand deposits that are found in Utah. Major objectives of the program were as follows: determine the feasibility of in situ recovery methods applied to tar sand deposits; and establish a system for classifying tar sand deposits relative to those characteristics that would affect the design and operation of various in situ recovery processes. Contents of this report include: (1) characterization of Utah tar sand; (2) laboratory extraction studies relative to Utah tar sand in situ methods; (3) geological site evaluation; (4) environmental assessments and water availability; (5) reverse combustion field experiment, TS-1C; (6) a reverse combustion followed by forward combustion field experiment, TS-2C; (7) tar sand permeability enhancement studies; (8) two-well steam injection experiment; (9) in situ steam-flood experiment, TS-1S; (10) design of a tar sand field experiment for air-stream co-injection, TS-4; (11) wastewater treatment and oil analyses; (12) economic evaluation of an in situ tar sand recovery process; and (13) appendix I (extraction studies involving Utah tar sands, surface methods). 70 figs., 68 tabs.

The investigation of radionuclides distributions in beach sand by ...

African Journals Online (AJOL)

The investigation of radionuclides distributions in beach sand by means of GIS techniques. ... The PDF file you selected should load here if your Web browser has a PDF reader plug-in installed (for example, a recent version of Adobe Acrobat Reader). If you would like more information about how to print, save, and work ...

Study on sand particles creep model and open pit mine landslide mechanism caused by sand fatigue liquefaction

Science.gov (United States)

Du, Dong-Ning; Wang, Lai-Gui; Zhang, Xiang-Dong; Zhang, Shu-Kun

2017-06-01

The sand particles in the sand - rock composite slope of the open pit mine occurs creep deformation and fatigue liquefaction under the action of vehicle load vibration and hydraulic gradient, which causes landslide geological disasters and it destroys the surface environment. To reveal the mechanism, a mechanics model based on the model considering the soil structural change with a new “plastic hinge” element is developed, to improve its constitutive and creep curve equations. Data from sand creep experiments are used to identify the parameters in the model and to validate the model. The results show that the mechanical model can describe the rotation progress between the sand particles, disclose the negative acceleration creep deformation stage during the third phase, and require fewer parameters while maintaining accuracy. It provides a new creep model considering rotation to analyze sand creep mechanism, which provides a theoretical basis for revealing the open pit mine landslide mechanism induced by creep deformation and fatigue liquefaction of sandy soil.

Retorting of bituminous sands

Energy Technology Data Exchange (ETDEWEB)

Chaney, P E; Ince, R W; Mason, C M

1872-09-26

This method of recovering oil from mined tar sands involves forming compacted tar sands pieces by special conditioning treatment that provides low internal permeability. The compacted pieces are then retorted in fixed bed form. The conditioning treatment can involve rolling of preformed pellets, compaction in a mold or pressure extrusion. Substantial collapsing of the bed during retorting is avoided. (9 claims) (Abstract only - original article not available from T.U.)

A Canadian perspective on the supply costs, production and economic impacts from oil sands development

International Nuclear Information System (INIS)

McColl, D.; Masri, M.

2008-01-01

This article provided a synopsis of oil sands research recently conducted at the Canadian Energy Research Institute (CERI). The production profiles and capital expenditures that CERI has projected for oil sands projects were explored along with the macroeconomic benefits associated with oil sands development. In addition to rising capital and operating costs, bitumen producers are challenged by labour shortages and environmental concerns. However, CERI warrants continued growth in production from the oil sands industry, given the current high price state of the global oil market and security of supply concerns from oil importing countries. This article also provided background information and analysis to assess the implications of future development. The projected growth in the oil sands industry creates demands for infrastructure, housing, health care, education, and business services. The economic impacts were measured at the local, provincial, national and global levels in terms of changes in gross domestic product; changes in employment; and, changes in government revenues. It was concluded that with continued investment and development, Alberta's oil sands resource is expected to continue to produce oil for decades, and would eventually achieve 6 MMbpd production. 8 refs., 3 tabs., 10 figs

Evaluating the oil sands reclamation process: Assessing policy capacity and stakeholder access for government and non-governmental organizations operating in Alberta's oil sands

Science.gov (United States)

Patterson, Tyler

. In an effort to discern the overall status of reclamation in the oil sands this study explores several factors essential to policy capacity: work environment, training, employee attitudes, perceived capacity, policy tools, evidence based work, and networking. Data was collected through key informant interviews with senior policy professionals in government and non-government agencies in Alberta. The following are agencies of interest in this research: Canadian Association of Petroleum Producers (CAPP); Alberta Environment and Sustainable Resource Development (AESRD); Alberta Energy Regulator (AER); Cumulative Environmental Management Association (CEMA); Alberta Environment Monitoring, Evaluation, and Reporting Agency (AEMERA); Wood Buffalo Environmental Association (WBEA). The aim of this research is to explain how and why reclamation policy is conducted in Alberta's oil sands. This will illuminate government capacity, NGO capacity, and the interaction of these two agency typologies. In addition to answering research questions, another goal of this project is to show interpretive analysis of policy capacity can be used to measure and predict policy effectiveness. The oil sands of Alberta will be the focus of this project, however, future projects could focus on any government policy scenario utilizing evidence-based approaches.

Use of sand wave habitats by silver hake

Science.gov (United States)

Auster, P.J.; Lindholm, J.; Schaub, S.; Funnell, G.; Kaufman, L.S.; Valentine, P.C.

2003-01-01

Silver hake Merluccius bilinearis are common members of fish communities in sand wave habitats on Georges Bank and on Stellwagen Bank in the Gulf of Maine. Observations of fish size v. sand wave period showed that silver hake are not randomly distributed within sand wave landscapes. Regression analyses showed a significant positive relationship between sand wave period and fish length. Correlation coefficients, however, were low, suggesting other interactions with sand wave morphology, the range of current velocities, and available prey may also influence their distribution. Direct contact with sand wave habitats varied over diel periods, with more fish resting on the seafloor during daytime than at night. Social foraging, in the form of polarized groups of fish swimming in linear formations during crepuscular and daytime periods, was also observed. Sand wave habitats may provide shelter from current flows and mediate fish-prey interactions. ?? 2003 The Fisheries Society of the British Isles.

Differentiation of Palaeogene sand by glauconitic and geochemical fingerprinting, Siri Canyon, Danish North Sea

Energy Technology Data Exchange (ETDEWEB)

Olivarius, M.; Knudsen, Christian; Svendsen, Johan B.

2011-07-01

The submarine Siri Canyon is NE-SW-oriented and located in the Danish North Sea. It contains a number of oil reservoirs with glauconite-rich sand. The reservoirs of interest in the Nini oil field are the Late Paleocene Tyr Member of the Lista Formation and the Kolga Member of the Sele Formation, presumably of Early Eocene age. These members have previously been known as the Ty and Hermod members. The sand shows signs of injection, both in cores and in seismic data. The aim of this work is to chemically characterise and fingerprint the sand in order to reveal the origin of the sand found in three horizontal wells, which could have been injected from one or both of the Tyr and Kolga members. Core samples were collected from two vertical wells of known stratigraphy to make a basis of comparison, whereas samples of the cuttings were collected from the three horizontal wells with ages primarily corresponding to the Kolga Member. The purpose was moreover to evaluate whether cuttings samples can be used for fingerprinting as an alternative to core samples. The interest in discriminating between the ages of the injected sand is the fact that the reservoir properties (porosity and permeability) are largely controlled by the original composition of the sand. Consequently, results from this study could affect the property modelling of the field. (LN)

Tidal dynamics in the sand motor lagoon

NARCIS (Netherlands)

De Vries, S.; Radermacher, M.; De Schipper, M.A.; Stive, M.J.F.

2015-01-01

The Sand Motor is a mega-nourishment characterized by a very large sand volume of around 20 million m3 placed along the Dutch coast. The Sand Motor is a pilot project to evaluate the performance of an alternative nourishment strategy with respect to different functions of the coastal system. Within

Class I cultural resource overview for oil shale and tar sands areas in Colorado, Utah and Wyoming.

Energy Technology Data Exchange (ETDEWEB)

O' Rourke, D.; Kullen, D.; Gierek, L.; Wescott, K.; Greby, M.; Anast, G.; Nesta, M.; Walston, L.; Tate, R.; Azzarello, A.; Vinikour, B.; Van Lonkhuyzen, B.; Quinn, J.; Yuen, R.; Environmental Science Division

2007-11-01

In August 2005, the U.S. Congress enacted the Energy Policy Act of 2005, Public Law 109-58. In Section 369 of this Act, also known as the 'Oil Shale, Tar Sands, and Other Strategic Unconventional Fuels Act of 2005', Congress declared that oil shale and tar sands (and other unconventional fuels) are strategically important domestic energy resources that should be developed to reduce the nation's growing dependence on oil from politically and economically unstable foreign sources. The Bureau of Land Management (BLM) is developing a Programmatic Environmental Impact Statement (PEIS) to evaluate alternatives for establishing commercial oil shale and tar sands leasing programs in Colorado, Wyoming, and Utah. This PEIS evaluates the potential impacts of alternatives identifying BLM-administered lands as available for application for commercial leasing of oil shale resources within the three states and of tar sands resources within Utah. The scope of the analysis of the PEIS also includes an assessment of the potential effects of future commercial leasing. This Class I cultural resources study is in support of the Draft Oil Shale and Tar Sands Resource Management Plan Amendments to Address Land Use Allocations in Colorado, Utah, and Wyoming and Programmatic Environmental Impact Statement and is an attempt to synthesize archaeological data covering the most geologically prospective lands for oil shale and tar sands in Colorado, Utah, and Wyoming. This report is based solely on geographic information system (GIS) data held by the Colorado, Utah, and Wyoming State Historic Preservation Offices (SHPOs). The GIS data include the information that the BLM has provided to the SHPOs. The primary purpose of the Class I cultural resources overview is to provide information on the affected environment for the PEIS. Furthermore, this report provides recommendations to support planning decisions and the management of cultural resources that could be impacted by future

Numerical simulation of flow and compression of green sand

DEFF Research Database (Denmark)

Hovad, Emil

The focus of the industrial PhD project was concentrated on the production of the sand mold (green sand) which gives the cast component its final geometrical shape. In order to ensure a high quality of the cast component, it is important to control the manufacturing process of the mold itself so...... that it is homogeneous and stable. Therefore gaining a basic understanding of how the flow and deposition of green sand should be characterized and modelled was important, so that it could be used for simulation of the manufacturing process of the sand mold. The flowability of the green sand is important when the sand...... flows down through the hopper filling the chamber with sand during the sand shot. The flowability of green sand is mostly governed by the amount of water and bentonite which both decrease it. The flowability and the internal forces thus control how well you can fill a complex mold geom-etry in which...

Phlebotomine sand flies (Diptera: Psychodidae in the Greek Aegean Islands: ecological approaches

Directory of Open Access Journals (Sweden)

Nikolaos Tsirigotakis

2018-02-01

Full Text Available Abstract Background Blood-sucking phlebotomine sand flies are the vectors of the protozoan parasites Leishmania spp. Different Phlebotomus species transmit different Leishmania species causing leishmaniases which are neglected diseases emerging/reemerging in new regions. Thirteen sand fly species, ten belonging to the medically important genus Phlebotomus and three belonging to Sergentomyia are known in Greece. An increasing number of human and dog cases are reported each year from all parts of the country including the Aegean Islands. However, no previous study has been conducted on the sand fly fauna on the islands, except for Rhodes and Samos. The aim of this study was to investigate sand fly species in eleven small Aegean islands; to understand species-specific relationships with environmental and climatic factors and to compare sand fly community parameters among islands. A risk analysis was carried out for each species using climatic and environmental variables. Results Nine sand fly species: Phlebotomus neglectus, P. tobbi, P. similis, P. simici, P. perfiliewi, P. alexandri, P. papatasi, Sergentomyia minuta and S. dentata, were collected from the islands studied. Phlebotomus (Adlerius sp. and Sergentomyia sp. specimens were also collected but not identified to the species level. There was a positive effect of distance from the sea on the abundance of P. neglectus, S. minuta and S. dentata, and a negative effect on the abundance of P. tobbi, P. simici and P. similis. In general, temperature preferences of sand fly populations were between 21 and 29 °C. Nevertheless, there were significant differences in terms of temperature and relative humidity preference ranges among species. The most important species found, P. neglectus, was indisputably the most adapted species in the study area with a very high reaction norm, favoring even the lower temperature and humidity ranges. Overall, the sand fly fauna in the islands was very rich but there

Sand wave fields beneath the Loop Current, Gulf of Mexico: Reworking of fan sands

Science.gov (United States)

Kenyon, Neil H.; Akhmetzhanov, A.M.; Twichell, D.C.

2002-01-01

Extensive fields of large barchan-like sand waves and longitudinal sand ribbons have been mapped by deep-towed SeaMARC IA sidescan sonar on part of the middle and lower Mississippi Fan that lies in about 3200 m of water. The area is beneath the strongly flowing Loop Current. The bedforms have not been adequately sampled but probably consist of winnowed siliciclastic-foraminiferal sands. The size (about 200 m from wingtip to wingtip) and shape of the large barchans is consistent with a previously observed peak current speed of 30 cm/s, measured 25 m above the seabed. The types of small-scale bedforms and the scoured surfaces of chemical crusts, seen on nearby bottom photographs, indicate that near-bed currents in excess of 30 cm/s may sometimes occur. At the time of the survey the sand transport direction was to the northwest, in the opposite direction to the Loop Current but consistent with there being a deep boundary current along the foot of the Florida Escarpment. Some reworking of the underlying sandy turbidites and debris flow deposits is apparent on the sidescan sonar records. Reworking by deep-sea currents, resulting in erosion and in deposits characterised by coarsening upwards structures and cross-bedding, is a process that has been proposed for sand found in cores in shallower parts of the Gulf of Mexico. This process is more widespread than hitherto supposed. 

Oil sands and the environment

Energy Technology Data Exchange (ETDEWEB)

Seeley, R. [Shell Canada Ltd., Calgary, AB (Canada). Calgary Research Centre

2004-07-01

Oil sands are a significant resource for Alberta and Canada with continuing growth opportunity. There is a need to ensure sustainable development of the oil sands resources from a social, economic and environmental perspective. The industry has succeeded in terms of proven reserves, technology advancements, reduced operating costs, reliability and market accessibility. Some of the major challenges facing the industry include high capital cost, infrastructure, social services and keeping pace with growth. This presentation outlined the proactive measures that the oil sands industry has taken to manage environmental issues such as sulphur dioxide and nitrogen oxide emissions, greenhouse gases, water management and land reclamation. tabs., figs.

Alberta oil sands royalty regime

International Nuclear Information System (INIS)

Asgarpour, S.

2004-01-01

The long term objective of the Oil Sands Business Unit of Alberta Energy is to pave the way for Alberta's bitumen production to reach 3 million barrels per day by 2020. This presentation described the national government's role in resource development. It was emphasized that since the Crown is the owner of the oil sands resource, it would benefit by providing strategic leadership and by generating a larger royalty base. The oil sands fiscal regime was described with reference to generic royalty, risk sharing, investment, and project economics. Business rule principles were also outlined along with criteria for project expansions. Both upstream and downstream challenges and opportunities were listed. 4 figs

Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

Directory of Open Access Journals (Sweden)

Nirmala D.B.

2016-06-01

Full Text Available This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37 Orthogonal Arrays (OA with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering “Nominal the better” situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

Science.gov (United States)

Nirmala, D. B.; Raviraj, S.

2016-06-01

This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC) containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37) Orthogonal Arrays (OA) with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering "Nominal the better" situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

A comparison of dimension reduction methods with application to multi-spectral images of sand used in concrete

DEFF Research Database (Denmark)

Clemmensen, Line Katrine Harder; Hansen, M. E.; Ersbøll, Bjarne Kjær

2010-01-01

This paper presents a comparison of dimension reduction methods based on a novel machine vision application for estimating moisture content in sand used to make concrete. For the application in question it is very important to know the moisture content of the sand so as to ensure good-quality...... sand types were examined with 20-60 images for each type. To reduce the amount of data, features were extracted from the multi-spectral images; the features were summary statistics on single bands and pairs of bands as well as morphological summaries. The number of features (2,016) is high in relation...

14821AT LANCE, Missile Number 2419, Round Number 349APT, 12 May 1980.

Science.gov (United States)

1980-05-01

WSTRUCTIONUREPOT DCUMNTAIONPAG EPORE COMPLEMON PORN REPORT NUMBER 2GOTACCESSION NO S. RECIPIENT’S CATALOG NUMBER TDR 1148 __7 0_____T___ ~. *.~----...,S. TYPE OF...Data at 0815 MDT ---------- 4 4. White Sands Desert Site (WSD) Significant Level Data at 0815 MDT ------------------------------------ 5 5. WSD Upper...humidity, dew point (0 C), density (gm/n,3), Wind direction and speed, and cloud cover were made at the LC-39 Met Site at T-0 minutes. (2) Monitor of

Comparative decay of Catellicoccus marimmalium and enterococci in beach sand and seawater.

Science.gov (United States)

Brown, Kendra I; Boehm, Alexandria B

2015-10-15

Most studies characterize microbial source tracking (MST) target performance using sensitivity and specificity metrics. However, it is important to also consider the temporal stability of MST targets in relation to regulated microbial pollutants. Differences among bacterial target stabilities may lead to erroneous conclusions about sources of contamination. The present study evaluates the relative stability of MST targets and fecal indicator organisms using the gull/pigeon-associated Catellicoccus marimammalium (CAT) marker and enterococci (ENT). The decay rates of CAT and ENT measured by culture (cENT) and QPCR (tENT) were compared in sand and seawater laboratory microcosms under environmentally relevant conditions (subject to tidal wetting versus no wetting in sand, and sunlit versus dark conditions in seawater). Bacterial targets were more persistent in beach sand than in seawater with decay rates on the order of 0.01-0.1 per day and 1 to 10 per day, respectively. Targets were more persistent in unwetted compared to wetted sand, and dark compared to sunlit seawater. During the first 8 days of the sand experiment, the decay rate k of CAT was greater than that of cENT. The decay rates of CAT, tENT, and cENT were similar in sand after day 8 and in dark seawater. In sunlit seawater, the decay rates were different between targets with kcENT > kCAT > ktENT. The decay rates presented here are useful for fate and transport models and also inform the use of MST marker concentrations to infer ENT sources in the environment. Copyright © 2015 Elsevier Ltd. All rights reserved.

Oil sands tailings management project

Energy Technology Data Exchange (ETDEWEB)

Godwalt, C. [Alberta WaterSMART, Calgary, AB (Canada); Kotecha, P. [Suncor Energy Inc, Calgary, AB (Canada); Aumann, C. [Alberta Innovates - Technology Futures, Alberta Governement, AB (Canada)

2010-11-15

The Oil sands leadership initiative (OSLI) works with the Government of Alberta on the development of the oil sands industry, considering environmental, economical and social aspects. Water management was identified as one of most important areas to focus on. Alberta WaterSMART was requested to support the development and the management of projects resulting from the work done or underway in this field. The development of a regional water management solution stood out as the most interesting solution to obtain significant results. In the Athabasca Region, oil sands producers work independently on their water sourcing and disposal with particular attention to fresh water conservation and economics. The Athabasca River represents a source for mines and distant saline aquifers are the target of steam assisted gravity drainage (SAGD) operators. As part of a four-phase project aiming to study the environmental and economic footprint (EEF) benefit of alternatives for Athabasca oil sands production water supply and disposal, the purpose of the tailings water management project was to identify tailings treatment technologies that are ready to be implemented, and to design and evaluate solutions in order to improve regional oil sands production water sourcing and disposal. Alternatives were evaluated based on their total EEF, applying a lifecycle assessment methodology with a particular attention on the quantification of important performance indicators. 25 refs., 8 tabs., 40 figs.

Oil sands tailings management project

International Nuclear Information System (INIS)

Godwalt, C.; Kotecha, P.; Aumann, C.

2010-11-01

The Oil sands leadership initiative (OSLI) works with the Government of Alberta on the development of the oil sands industry, considering environmental, economical and social aspects. Water management was identified as one of most important areas to focus on. Alberta WaterSMART was requested to support the development and the management of projects resulting from the work done or underway in this field. The development of a regional water management solution stood out as the most interesting solution to obtain significant results. In the Athabasca Region, oil sands producers work independently on their water sourcing and disposal with particular attention to fresh water conservation and economics. The Athabasca River represents a source for mines and distant saline aquifers are the target of steam assisted gravity drainage (SAGD) operators. As part of a four-phase project aiming to study the environmental and economic footprint (EEF) benefit of alternatives for Athabasca oil sands production water supply and disposal, the purpose of the tailings water management project was to identify tailings treatment technologies that are ready to be implemented, and to design and evaluate solutions in order to improve regional oil sands production water sourcing and disposal. Alternatives were evaluated based on their total EEF, applying a lifecycle assessment methodology with a particular attention on the quantification of important performance indicators. 25 refs., 8 tabs., 40 figs.

Microbial processes in the Athabasca Oil Sands and their potential applications in microbial enhanced oil recovery.

Science.gov (United States)

Harner, N K; Richardson, T L; Thompson, K A; Best, R J; Best, A S; Trevors, J T

2011-11-01

The Athabasca Oil Sands are located within the Western Canadian Sedimentary Basin, which covers over 140,200 km(2) of land in Alberta, Canada. The oil sands provide a unique environment for bacteria as a result of the stressors of low water availability and high hydrocarbon concentrations. Understanding the mechanisms bacteria use to tolerate these stresses may aid in our understanding of how hydrocarbon degradation has occurred over geological time, and how these processes and related tolerance mechanisms may be used in biotechnology applications such as microbial enhanced oil recovery (MEOR). The majority of research has focused on microbiology processes in oil reservoirs and oilfields; as such there is a paucity of information specific to oil sands. By studying microbial processes in oil sands there is the potential to use microbes in MEOR applications. This article reviews the microbiology of the Athabasca Oil Sands and the mechanisms bacteria use to tolerate low water and high hydrocarbon availability in oil reservoirs and oilfields, and potential applications in MEOR.

Characteristics of SCC with Fly Ash and Manufactured Sand

Science.gov (United States)

Praveen Kumar, K.; Radhakrishna

2016-09-01

Self compacting concrete (SCC) of M40 grade was designed. The binder in SCC consists of OPC and fly ash in the ratio of 65:35. River sand was replaced by manufactured sand (M-sand) at replacement levels of 20,40,60,80 and 100%. An attempt was made to evaluate the workability and strength characteristics of self compacting concrete with river sand and manufactured sand as fine aggregates. For each replacement level, constant workability was maintained by varying the dosage of superplasticizer. T50 flow time, V Funnel time, V-funnel T5 time as well as compressive, split tensile and flexural strength of SCC were found at each replacement level of M-sand. They were compared to SCC with river sand. Results indicate favourable use of M-sand in preparation of Self Compacting Concrete.

Properties of dune sand concrete containing coffee waste

Directory of Open Access Journals (Sweden)

Mohamed Guendouz

2018-01-01

Full Text Available In the last years, an increase of coffee beverages consumption has been observed all over the world; and its consumption increases the waste coffee grounds which will become an environmental problems. Recycling of this waste to produce new materials like sand concrete appears as one of the best solutions for reduces the problem of pollution. This work aims to study the possibility of recycling waste coffee grounds (Spent Coffee Grounds (SCG as a fine aggregate by replacing the sand in the manufacturing of dune sand concrete. For this; sand concrete mixes were prepared with substitution of sand with the spent coffee grounds waste at different percentage (0%, 5%, 10%, 15% and 20% by volume of the sand in order to study the influence of this wastes on physical (Workability, bulk density and porosity, mechanical (compressive and flexural strength and Thermal (Thermal conductivity and thermal diffusivity properties of dune sand concrete. The results showed that the use of spent coffee grounds waste as partial replacement of natural sand contributes to reduce workability, bulk density and mechanical strength of sand concrete mixes with an increase on its porosity. However, the thermal characteristics are improved and especially for a level of 15% and 20% of substitution. So, it is possible to obtain an insulating material which can be used in the various types of structural components. This study ensures that reusing of waste coffee grounds in dune sand concrete gives a positive approach to reduce the cost of materials and solve some environmental problems.

Documenting the global impacts of beach sand mining

Science.gov (United States)

Young, R.; Griffith, A.

2009-04-01

For centuries, beach sand has been mined for use as aggregate in concrete, for heavy minerals, and for construction fill. The global extent and impact of this phenomenon has gone relatively unnoticed by academics, NGOs, and major news sources. Most reports of sand mining activities are found at the very local scale (if the mining is ever documented at all). Yet, sand mining in many localities has resulted in the complete destruction of beach (and related) ecosystems along with severe impacts to coastal protection and tourism. The Program for the Study of Developed Shorelines at Western Carolina University and Beachcare.org have initiated the construction of a global database of beach sand mining activities. The database is being built through a combination of site visits and through the data mining of media resources, peer reviewed papers, and reports from private and governmental entities. Currently, we have documented sand mining in 35 countries on 6 continents representing the removal of millions of cubic meters of sand. Problems extend from Asia where critical infrastructure has been disrupted by sand mining to the Caribbean where policy reform has swiftly followed a highly publicized theft of sand. The Program for the Study of Developed Shorelines recently observed extensive sand mining in Morocco at the regional scale. Tens of kilometers of beach have been stripped of sand and the mining continues southward reducing hope of a thriving tourism-based economy. Problems caused by beach sand mining include: destruction of natural beaches and the ecosystems they protect (e.g. dunes, wetlands), habitat loss for globally important species (e.g. turtles, shorebirds), destruction of nearshore marine ecosystems, increased shoreline erosion rates, reduced protection from storms, tsunamis, and wave events, and economic losses through tourist abandonment and loss of coastal aesthetics. The threats posed by sand mining are made even more critical given the prospect of a

Studies on various characteristics of concrete structures using crushed sand

International Nuclear Information System (INIS)

Mimatsu, Makoto; Sugita, Hideaki; Yonemura, Masataka.

1985-01-01

With the recent advances of construction industry, the demands for concrete, hence for aggregate, are rising. The sand as such is in extreme shortage due to the exhaustion of river sand. Under the situation, the recent trends are for the use of crushed sand, i.e. the artificial sand obtained by crushing rocks, which have advantages of stabilized quality and adequate supplies. In building of nuclear power plants requiring large amounts of concrete, the usage of crushed sand is now unavoidable. The following are described : the situation of aggregate in Kyushu. production method of crushed sand and the quality standards, rocks used for crushed stone and sand and the properties, quality survey on crushed sand and the basic tests, characteristic tests of crushed-stone and -sand mixed concrete, the application of crushed sand in structures of the Sendai Nuclear Power Station. (Mori, K.)

Laboratory observations of artificial sand and oil agglomerates

Science.gov (United States)

Jenkins, Robert L.; Dalyander, P. Soupy; Penko, Allison; Long, Joseph W.

2018-04-27

Sand and oil agglomerates (SOAs) form when weathered oil reaches the surf zone and combines with suspended sediments. The presence of large SOAs in the form of thick mats (up to 10 centimeters [cm] in height and up to 10 square meters [m2] in area) and smaller SOAs, sometimes referred to as surface residual balls (SRBs), may lead to the re-oiling of beaches previously affected by an oil spill. A limited number of numerical modeling and field studies exist on the transport and dynamics of centimeter-scale SOAs and their interaction with the sea floor. Numerical models used to study SOAs have relied on shear-stress formulations to predict incipient motion. However, uncertainty exists as to the accuracy of applying these formulations, originally developed for sand grains in a uniformly sorted sediment bed, to larger, nonspherical SOAs. In the current effort, artificial sand and oil agglomerates (aSOAs) created with the size, density, and shape characteristics of SOAs were studied in a small-oscillatory flow tunnel. These experiments expanded the available data on SOA motion and interaction with the sea floor and were used to examine the applicability of shear-stress formulations to predict SOA mobility. Data collected during these two sets of experiments, including photographs, video, and flow velocity, are presented in this report, along with an analysis of shear-stress-based formulations for incipient motion. The results showed that shear-stress thresholds for typical quartz sand predicted the incipient motion of aSOAs with 0.5–1.0-cm diameters, but were inaccurate for aSOAs with larger diameters (>2.5 cm). This finding implies that modified parameterizations of incipient motion may be necessary under certain combinations of aSOA characteristics and environmental conditions.

Influence of sand base preparation on properties of chromite moulding sands with sodium silicate hardened with selected methods

Directory of Open Access Journals (Sweden)

Stachowicz M.

2017-03-01

Full Text Available The paper presents a research on the relation between thermal preparation of chromite sand base of moulding sands containing sodium silicate, hardened with selected physical and chemical methods, and structure of the created bonding bridges. Test specimens were prepared of chromite sand - fresh or baked at 950°C for 10 or 24 hours - mixed with 0.5 wt.% of the selected non-modified inorganic binder and, after forming, were hardened with CO2 or liquid esters, dried traditionally or heated with microwaves at 2.45 GHz. It was shown on the grounds of SEM observations that the time of baking the base sand and the hardening method significantly affect structure of the bonding bridges and are correlated with mechanical properties of the moulding sands. It was found that hardening chromite-based moulding mixtures with physical methods is much more favourable than hardening with chemical methods, guaranteeing also more than ten times higher mechanical properties.

Experimental perforation of tubing with a hydraulic sand jet

Energy Technology Data Exchange (ETDEWEB)

Semenov, Yu V

1970-01-01

A series of field tests has shown that perforation with a hydraulic sand jet improves the quality of well completion. The sand jet does not crack the cement sheath or the casing, and the perforations are larger and deeper than perforations formed by explosive charges. Fluid circulation during sand jet perforation can safely be stopped for at least 10 min. Water containing a surfactant can be used as a sand carrier. Sand jet perforation allows successful completion of wells cased by 2 tubing strings. Sand jet perforation can be used to clean the borehole well and to remove foreign objects from the well.

Effect of manufactured sand on the durability characteristics of concrete

Directory of Open Access Journals (Sweden)

S. S. SARAVANAN

2016-12-01

Full Text Available Concrete is the most sought after material due to increase in construction activities and infrastructural developments. Availability of natural sand is decreasing thereby increase in the cost of construction. In the present work undertaken, an attempt has been made to give an alternative to natural sand. Optimization of replacement of natural sand with manufactured sand in concrete, durability studies such as water absorption, rapid chloride permeability test, sorptivity, acid resistance, alkaline resistance, impact resistance and abrasion resistance of M40 and M50 grades of concrete have been studied with manufactured sand as fine aggregate and compared the results with the conventional sand concrete. The results shows that there is an increase in the durability properties up to 70 % level of replacements of sand with manufactured sand as fine aggregate and for 100 % use of manufactured sand also gives the better durability than the conventional sand concrete.

Experimental Study on Superfine Sand Concrete Mixed by Double Mixing Technology

OpenAIRE

yuqing zhao

2013-01-01

Traditional concept thought that medium sand and fine sand can be used to mix concrete, superfine sand can not used to mix concrete. This makes the source of superfine sand limited. With the shortage of medium sand and fine sand, it is imperative to exploit the resource of superfine sand. Superfine sand concrete is mixed by means of Double-doped Technology-ultra-fine fly ash and super plasticizer. Primary factor influencing superfine sand concrete strength is studied by orthogonal test, the o...

The physics of wind-blown sand and dust.

Science.gov (United States)

Kok, Jasper F; Parteli, Eric J R; Michaels, Timothy I; Karam, Diana Bou

2012-10-01

The transport of sand and dust by wind is a potent erosional force, creates sand dunes and ripples, and loads the atmosphere with suspended dust aerosols. This paper presents an extensive review of the physics of wind-blown sand and dust on Earth and Mars. Specifically, we review the physics of aeolian saltation, the formation and development of sand dunes and ripples, the physics of dust aerosol emission, the weather phenomena that trigger dust storms, and the lifting of dust by dust devils and other small-scale vortices. We also discuss the physics of wind-blown sand and dune formation on Venus and Titan.

Phlebotomine sand flies in Porteirinha, an area of American visceral leishmaniasis transmission in the State of Minas Gerais, Brazil

Directory of Open Access Journals (Sweden)

Ricardo Andrade Barata

2004-08-01

Full Text Available A study of the phlebotomine sand fly fauna was carried out in an endemic area of American visceral leishmaniasis (AVL in the municipality of Porteirinha, in the Brazilian state of Minas Gerais. Captures were performed with CDC light traps in 7 districts, 5 days per month, during 2 consecutive years (January 2000 to December 2001. A total of 3240 sand flies were captured and identified. Sixteen species were found, among which 15 belonged to the genus Lutzomyia and one to the genus Brumptomyia. Lutzomyia longipalpis, a proven vector of AVL, was the predominant species (71.85% throughout the time period. The interference of climatic factors (temperature, humidity, and rainfall over the populational dynamics of the sand flies was determined. Statistical analysis of the data showed a significant correlation among the number of phlebotomine sand flies collected, rainfall, and humidity, whereas the effect of temperature was negligible, in that particular region. The amount of collected phlebotomine, the number of human cases, and the prevalence of canine AVL in the districts of Porteirinha are discussed.

Monitoring and ming bio-physical parameters for hypoxia hazard in a coastal sand pit

DEFF Research Database (Denmark)

Mariani, Patrizio; Benassai, Guido; Grieco, Luisa

2018-01-01

Management of coastal areas requires monitoring and modeling of the anthropogenic drivers and the bio-physical processes affecting water quality. To assess the range of hydrographic conditions controlling oxygen distribution in the bottom layers of sand pits, a multi-year oceanographic survey has...... of the sand pits is associated with higher temperatures and wind speed lower than 5 m/s, which is not infrequent during the summer season. However, the number of consecutive days of oxygen depletion can be considered lower than the danger threshold level assumed in the literature....

Mineral Resource Assessment of Marine Sand Resources in Cape- and Ridge-Associated Marine Sand Deposits in Three Tracts, New York and New Jersey, United States Atlantic Continental Shelf

Science.gov (United States)

Bliss, James D.; Williams, S. Jeffress; Arsenault, Matthew A.

2009-01-01

Demand is growing in the United States and worldwide for information about the geology of offshore continental shelf regions, the character of the seafloor, and sediments comprising the seafloor and subbottom. Interest in locating sand bodies or high quality deposits that have potential as sources for beach nourishment and ecosystem restoration is especially great in some regions of the country. The Atlantic coast, particularly New York and New Jersey, has been the focus of these studies for the past 40 years with widely varying results. This study is the first attempt at applying probability statistics to modeling Holocene-age cape-and ridge-associated sand deposits and thus focuses on distinct sand body morphology. This modeling technique may have application for other continental shelf regions that have similar geologic character and late Quaternary sea-level transgression history. An estimated volume of 3.9 billion m3 of marine sand resources is predicted in the cape-and ridge-associated marine sand deposits in three representative regions or tracts on the continental shelf offshore of New York and New Jersey. These estimates are taken from probabilistic distributions of sand resources and are produced using deposit models and Monte Carlo Simulation (MCS) techniques. The estimated sand resources presented here are for only three tracts as described below and for Holocene age sand resources contained in cape-and ridge-associated marine sand deposit types within this area. Other areas may qualify as tracts for this deposit type and other deposit types and geologic ages (for example, paleo-stream channels, blanket and outwash deposits, ebb-tide shoals, and lower sea level-stand deltas), which are present on the New Jersey and New York continental shelf area but are not delineated and modeled in this initial evaluation. Admittedly, only a portion of these probable sand resources will ultimately be available and suitable for production, dependent largely on

Sand Dunes with Frost

Science.gov (United States)

2004-01-01

9 May 2004 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows a suite of frost-covered sand dunes in the north polar region of Mars in early spring, 2004. The dunes indicate wind transport of sand from left to right (west to east). These landforms are located near 78.1oN, 220.8oW. This picture is illuminated by sunlight from the lower left and covers an area about 3 km (1.9 mi) across.

Relationships between sand and water quality at recreational beaches.

Science.gov (United States)

Phillips, Matthew C; Solo-Gabriele, Helena M; Piggot, Alan M; Klaus, James S; Zhang, Yifan

2011-12-15

Enterococci are used to assess the risk of negative human health impacts from recreational waters. Studies have shown sustained populations of enterococci within sediments of beaches but comprehensive surveys of multiple tidal zones on beaches in a regional area and their relationship to beach management decisions are limited. We sampled three tidal zones on eight South Florida beaches in Miami-Dade and Broward counties and found that enterococci were ubiquitous within South Florida beach sands although their levels varied greatly both among the beaches and between the supratidal, intertidal and subtidal zones. The supratidal sands consistently had significantly higher (p sand) than the other two zones. Levels of enterococci within the subtidal sand correlated with the average level of enterococci in the water (CFU/100mL) for the season during which samples were collected (r(s) = 0.73). The average sand enterococci content over all the zones on each beach correlated with the average water enterococci levels of the year prior to sand samplings (r(s) = 0.64) as well as the average water enterococci levels for the month after sand samplings (r(s) = 0.54). Results indicate a connection between levels of enterococci in beach water and sands throughout South Florida's beaches and suggest that the sands are one of the predominant reservoirs of enterococci impacting beach water quality. As a result, beaches with lower levels of enterococci in the sand had fewer exceedences relative to beaches with higher levels of sand enterococci. More research should focus on evaluating beach sand quality as a means to predict and regulate marine recreational water quality. Copyright © 2011 Elsevier Ltd. All rights reserved.

Compressive Strength of Compacted Clay-Sand Mixes

Directory of Open Access Journals (Sweden)

Faseel Suleman Khan

2014-01-01

Full Text Available The use of sand to improve the strength of natural clays provides a viable alternative for civil infrastructure construction involving earthwork. The main objective of this note was to investigate the compressive strength of compacted clay-sand mixes. A natural clay of high plasticity was mixed with 20% and 40% sand (SP and their compaction and strength properties were determined. Results indicated that the investigated materials exhibited a brittle behaviour on the dry side of optimum and a ductile behaviour on the wet side of optimum. For each material, the compressive strength increased with an increase in density following a power law function. Conversely, the compressive strength increased with decreasing water content of the material following a similar function. Finally, the compressive strength decreased with an increase in sand content because of increased material heterogeneity and loss of sand grains from the sides during shearing.

Oil sands to the rescue: oil sand microbial communities can degrade recalcitrant alkyl phenyl alkanoic acids

Energy Technology Data Exchange (ETDEWEB)

Whitby, Corinne [University of Essex (Canada)], email: cwhitby@essex.ac.uk

2011-07-01

Almost half of all global oil reserves are found as biodegraded heavy oils found in vast tar sand deposits located in North and South America and these account for 47% of Canadian oil production. Oil sand extraction generates large amounts of toxic waste water, known as oil sand process waters (OSPW), that are stored in large tailing ponds that contain toxic compounds like naphthenic acids (NAs). The presence of NAs creates problems like toxicity, corrosion, and the formation of calcium napthenate deposits which block pipelines and other infrastructure and need to be removed. This paper presents oil sand microbial communities that can degrade these NAs. The approach is to apply new aliphatic and aromatic NAs as substrates to supplement and identify NA degrading microbes and also to identify the metabolites produced and explain NA degradation pathways and the functional genes involved. The chemistry and the processes involved are explained. From the results, it is suggested that pure cultures of P. putida KT2440 be used against NAs.

Extraction of toxic and valuable metals from foundry sands

International Nuclear Information System (INIS)

Vite T, J.

1996-01-01

There were extracted valuable metals from foundry sands such as: gold, platinum, silver, cobalt, germanium, nickel and zinc among others, as well as highly toxic metals such as chromium, lead, vanadium and arsenic. The extraction efficiency was up to 100% in some cases. For this reason there were obtained two patents at the United States, patent number 5,356,601, in October 1994, given for the developed process and patent number 5,376,000, in December 1994, obtained for the equipment employed. Therefore, the preliminary parameters for the installation of a pilot plant have also been developed. (Author)

Strength and microstructure characteristics of the recycled rubber tire-sand mixtures as lightweight backfill.

Science.gov (United States)

Zhang, Tao; Cai, Guojun; Duan, Weihong

2018-02-01

The disposal of scrap rubber tires has induced critical environmental issue worldwide due to the rapid increase in the number of vehicles. Recycled scrap tires as a construction material in civil engineering have significant environmental benefits from a waste management perspective. A systematic study that deals with strength and microstructure characteristics of the rubber-sand mixtures is initiated, and mechanical response of the mixtures is discussed in this investigation. Experiments were conducted to evaluate the effects of rubber fraction on the basic properties including mass density (ρ), stress-strain characteristics, shear strength, and unconfined compression strength (q u ) of the rubber-sand mixtures. Additionally, scanning electron microscopy (SEM) was carried out to reveal the microstructure characteristics of the mixtures with various rubber fractions. A discussion on the micromechanics of the mixtures also was conducted. This study demonstrates that the ρ, friction angle, and q u decrease linearly with an increase in rubber fraction, whereas shear strain at peak increases. The stress-strain characteristics of the rubber-sand mixtures shift from brittle to ductile as the rubber fraction increase. These changes are attributed to remarkably lower stiffness and higher compressibility of the rubber particle compared with those of the conventional mineral aggregates. With an increase in the rubber fraction, the mechanical response of rubber-sand mixtures exhibits two types: sand-like material and rubber-like material. Rubber particle possesses the capacity to prevent the contacted sand particles from sliding at lower rubber fraction, whereas it transmits the applied loadings as the rubber fraction increased. This outcome reinforces the practicability of using recycled rubber tire-sand mixtures as a lightweight backfill in subbase/base applications.

Groundwater Discharges to Rivers in the Western Canadian Oil Sands Region

Science.gov (United States)

Ellis, J.; Jasechko, S.

2016-12-01

Groundwater discharges into rivers impacts the movement and fate of nutrients and contaminants in the environment. Understanding groundwater-surface water interactions is especially important in the western Canadian oil sands, where groundwater contamination risks are elevated and baseline water chemistry data is lacking, leading to substantial uncertainties about anthropogenic influences on local river quality. High salinity groundwater springs sourced from deep aquifers, comprised of Pleistocene-aged glacial meltwater, are known to discharge into many rivers in the oil sands. Understanding connections between deep aquifers and surficial waterways is important in order to determine natural inputs into these rivers and to assess the potential for injected wastewater or oil extraction fluids to enter surface waters. While these springs have been identified, their spatial distribution along rivers has not been fully characterized. Here we present river chemistry data collected along a number of major river corridors in the Canadian oil sands region. We show that saline groundwater springs vary spatially along the course of these rivers and tend to be concentrated where the rivers incise Devonian- or Cretaceous-aged aquifers along an evaporite dissolution front. Our results suggest that water sourced from Devonian aquifers may travel through bitumen-bearing Cretaceous units and discharge into local rivers, implying a strong groundwater-surface water connection in specialized locations. These findings indicate that oil sands process-affected waters that are injected at depth have the potential to move through these aquifers and reach the rivers at the surface at some time in the future. Groundwater-surface water interactions remain key to understanding the risks oil sands activities pose to aquatic ecosystems and downstream communities.

Stakeholder relations in the oil sands : managing uncertainty

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-05-15

Alberta's oil sands are now at the crossroads of a series of significant and complex global issues that will require careful negotiation by all stakeholders involved in the oil sands industry. This paper discussed methods of managing uncertainty and risk related to the oil sands industry's agenda for the future. Oil sands developers must continue to secure permission from communities and other key stakeholders in order to develop oil sand projects. Stakeholder relations between oil sands operators, First Nations, and Metis Nation communities must ensure that respect is maintained while environmental impacts are minimized and long-term economic benefits are secured for all parties. Environmental non-governmental organizations (ENGOs) must ensure that oil sands resources are developed responsibly, and that environmental standards are maintained. Seven key shifts in stakeholder relations resulting from the recent economic crisis were identified. These included (1) withdrawal from the multi-stakeholder process, (2) increased focus on government to demonstrate policy leadership, (3) a stronger push from ENGOs to express environmental concerns, (4) global lobby and public relations efforts from ENGOs, (5) companies retreating to local community stakeholders, (6) more active demands from First Nations and Metis Nations groups, and (7) companies challenging ENGO campaigns. The study concluded by suggesting that government leadership is needed to clear policy and regulatory frameworks for Canada's oil sands.

Providing floating capabilities in latest-generation sand screens

Energy Technology Data Exchange (ETDEWEB)

Bowen, E.G.; Coronado, M.P. [Society of Petroleum Engineers, Richardson, TX (United States)]|[Baker Hughes, Houston, TX (United States)

2008-10-15

Alternative production methods are needed for the massive reserves located in the bitumen region of Canada's tar sands. The area has over 100 installations of sand screens/slotted liners in both injection and production legs using steam-assisted gravity drainage (SAGD) technology. Multiple wells must be drilled from a single pad because of the sensitive nature of the environment. With significant depths of these wells, a floating sand screen provides assurance that the sand screen will reach the desired depth. Paraffin is generally used to plug the flow access of the screen during installation. This paper discussed a new technology that has been developed to allow for sand screen installations without relying on paraffin wax to withstand differential pressure. The new technology uses a hydro-mechanical valving system incorporated into the screen design to temporarily close off the screen while being run in the hole. The paper described how the technology could provide a reliable, time-saving solution for SAGD installations when floating sand control screens are needed. The paper discussed current technology and its limitations, sand screen installation, screen design for floating applications, and additional applications. It was concluded that this technology solution provides a unique alternative to the methods currently used to install sand screens with SAGD technology in the fast growing Canadian market for bitumen recovery. 2 refs., 5 figs.

Revegetation and management of tailings sand slopes from tar sand extraction: 1978 results

Energy Technology Data Exchange (ETDEWEB)

Rowell, M J

1979-01-01

The results are reported of research into the revegetation of two areas on a steeply sloping dike composed of tailings sand from tar sand extraction at the Great Canadian Oil Sand Limited plant at Fort McMurray, Alberta. One area was seeded with three pasture grasses and two legumes in 1971 after the slope surface had been mixed with peat to a depth of 15 cm. A second area had been amended with peat or peat and overburden and differing rates of fertilizer added. A mix containing nine grasses, four legumes, and oats, as a companion crop, was seeded in July 1976. The objectives of the research were to study methods for the establishment of a stable vegetative cover that would prevent erosion of the slope and, in time, might become a self maintaining unit. Tillage of soil amendments to a depth of 15 cm and 30 cm were compared in promoting deeper rooting and stabilizing of the slope.

Failure Mode and Effect Analysis (FMEA) Applications to Identify Iron Sand Reject and Losses in Cement Industry : A Case Study

Science.gov (United States)

Helia, V. N.; Wijaya, W. N.

2017-06-01

One of the main raw materials required in the manufacture of cement is iron sand. Data from the Procurement Department on XYZ Company shows that the number of defective iron sand (reject) fluctuates every month. Iron sand is an important raw material in the cement production process, so that the amount of iron sand reject and losses got financial and non-financial impact. This study aims to determine the most dominant activity as the cause of rejection and losses of iron sands and suggest improvements that can be made by using the approach of FMEA (Failure Mode and Effect Analysis). Data collection techniques in this study was using the method of observation, interviews, and focus group discussion (FGD) as well as the assessment of the experts to identify it. Results from this study is there are four points of the most dominant cause of the defect of iron sand (mining activities, acceptance, examination and delivery). Recommendation for overcoming these problem is presented (vendor improvement).

Developing new markets for oil sands products

International Nuclear Information System (INIS)

Crandall, G.

2004-01-01

This paper presents a review by Purvin and Gertz of western Canadian crude oil supply. This energy consulting firm provides advise to the energy sector. It suggests that oil sands production will surpass declining conventional production. Oil sands supply includes bitumen, synthetic crude oil (SCO), and diluent. It is forecasted that oil sands will increase from 42 per cent of western supply in 2002 to 78 per cent in 2015. The potential of Alberta's oil sands was discussed along with a recent study of refined products and petrochemicals from bitumen. Upgrading, refining and petrochemical case studies were presented. The author examined if a Canadian oil sands upgrading project with high capital costs can be competitive with competing projects in the United States and internationally. In addition to supply and demand issues, the presentation examined infrastructure capability and market potential in the United States. The economic potential and risks of preferred business cases compared to upgrading to SCO were also evaluated. 15 figs

The behavior of gaseous iodine in sand

International Nuclear Information System (INIS)

Takahashi, Kanji

1974-01-01

Radioactive iodine gas was passed through 10 different sands collected at rivers and hills. The relation between the amount of the loaded gas and the amount of adsorbed gas was determined at room temperature, 50 -- 60 0 C, and 90 -- 100 0 C under humidity of 2 sand. This amount was about 1 -- 3 times as much as that of monomolecular membrane adsorption, 0.2 -- 0.3 μg/cm 2 . The decrease of adsorption amount that accompanies the increase of humidity is attributable to the decrease of effective surface area of sand due to the presence of water. The transport of iodine in sand was studied by passing gaseous iodine through a glass tubing packed with sand. The distribution in the flow direction of iodine indicated that the ease of desorption depends upon the situation of adsorption. Easily desorbed case was named Henry type adsorption. Hardly desorbed case was named absorption type. Discussion is made on experimental results. (Fukutomi, T.)

Bioaugmentation of flow-through sand filters

DEFF Research Database (Denmark)

Samuelsen, Elin Djurhuus

for degradation performances in flow-through sand columns, with the aim of identifying a suitable inoculant strain for future environmental applications. Another aim was to identify a suitable genetic marker to monitor phenoxy acid degradation in strain Sphingobium sp. PM2. We were not able to link motility...... and biofilm formation to the strains´ ability to adhere to sand. Nevertheless, a correlation was found between cell surface hydrophobicity and adhesion and overall degradation performances in flow-through sand columns. We identified S phingobium sp. PM2 as a promising inoculant strain, displaying efficient...... MCPA degradation for prolonged periods in flow-through sand columns. In an expression study of catabolic genes with putative roles in phenoxy acid degradation, we observed a marked upregulation of catabolic genes cadA and tfdC upon exposure to MCPA, 2,4-D, dichlorprop and mecoprop in strain PM2, which...

Booming Sand Dunes

Science.gov (United States)

Vriend, Nathalie

"Booming" sand dunes are able to produce low-frequency sound that resembles a pure note from a music instrument. The sound has a dominant audible frequency (70-105 Hz) and several higher harmonics and may be heard from far distances away. A natural or induced avalanche from a slip face of the booming dune triggers the emission that may last for several minutes. There are various references in travel literature to the phenomenon, but to date no scientific explanation covered all field observations. This thesis introduces a new physical model that describes the phenomenon of booming dunes. The waveguide model explains the selection of the booming frequency and the amplification of the sound in terms of constructive interference in a confined geometry. The frequency of the booming is a direct function of the dimensions and velocities in the waveguide. The higher harmonics are related to the higher modes of propagation in the waveguide. The experimental validation includes quantitative field research at the booming dunes of the Mojave Desert and Death Valley National Park. Microphone and geophone recordings of the acoustic and seismic emission show a variation of booming frequency in space and time. The analysis of the sensor data quantifies wave propagation characteristics such as speed, dispersion, and nonlinear effects and allows the distinction between the source mechanism of the booming and the booming itself. The migration of sand dunes results from a complicated interplay between dune building, wind regime, and precipitation. The morphological and morphodynamical characteristics of two field locations are analyzed with various geophysical techniques. Ground-penetrating radar images the subsurface structure of the dunes and reveal a natural, internal layering that is directly related to the history of dune migration. The seismic velocity increases abruptly with depth and gradually increases with downhill position due to compaction. Sand sampling shows local

Construction of a test embankment using a sand-tire shred mixture as fill material.

Science.gov (United States)

Yoon, Sungmin; Prezzi, Monica; Siddiki, Nayyar Zia; Kim, Bumjoo

2006-01-01

Use of tire shreds in construction projects, such as highway embankments, is becoming an accepted way of beneficially recycling scrap tires. However, in the last decade there was a decline in the use of pure tire shreds as fill materials in embankment construction, as they are susceptible to fire hazards due to the development of exothermic reactions. Tire shred-sand mixtures, on the other hand, were found to be effective in inhibiting exothermic reactions. When compared with pure tire shreds, tire shred-sand mixtures are less compressible and have higher shear strength. However, the literature contains limited information on the use of tire shred-soil mixtures as a fill material. The objectives of this paper are to discuss and evaluate the feasibility of using tire shred-sand mixtures as a fill material in embankment construction. A test embankment constructed using a 50/50 mixture, by volume, of tire shreds and sand was instrumented and monitored to: (a) determine total and differential settlements; (b) evaluate the environmental impact of the embankment construction on the groundwater quality due to leaching of fill material; and (c) study the temperature variation inside the embankment. The findings in this research indicate that mixtures of tire shreds and sand are viable materials for embankment construction.

Effect of substrate size on sympatric sand darter benthic habitat preferences

Science.gov (United States)

Thompson, Patricia A.; Welsh, Stuart A.; Rizzo, Austin A.; Smith, Dustin M.

2017-01-01

The western sand darter, Ammocrypta clara, and the eastern sand darter, A. pellucida, are sand-dwelling fishes that have undergone range-wide population declines, presumably owing to habitat loss. Habitat use studies have been conducted for the eastern sand darter, but literature on the western sand darter remains sparse. To evaluate substrate selection and preference, western and eastern sand darters were collected from the Elk River, West Virginia, one of the few remaining rivers where both species occur sympatrically. In the laboratory, individuals were given the choice to bury into five equally available and randomly positioned substrates ranging from fine sand to granule gravel (0.12–4.0 mm). The western sand darter selected for coarse and medium sand, while the eastern sand darter was more of a generalist selecting for fine, medium, and coarse sand. Substrate selection was significantly different (p = 0.02) between species in the same environment, where the western sand darter preferred coarser substrate more often compared to the eastern sand darter. Habitat degradation is often a limiting factor for many species of rare freshwater fish, and results from this study suggest that western and eastern sand darters may respond differently to variations in benthic substrate composition.

The Geodiversity in Drift Sand Landscapes of The Netherlands

Science.gov (United States)

van den Ancker, Hanneke; Jungerius, Pieter Dirk; Riksen, Michel

2015-04-01

The authors carried out detailed field studies of more than twelve drift sand landscapes in The Netherlands. The objective of these studies was to restore Natura-2000 values by restoring the wind activity. Active drift sands occur almost exclusively in The Netherlands, Natura 2000 habitat 2330 'Inland dunes with open Corynephorus and Agrostis grasslands', for which reason our country is largely responsible for this European landscape. Active drift sands had almost disappeared for two reasons: first, the stabilization of the drift sands by air pollution, mainly nitrogen, which stimulates the growth of algae and grasses that initiate soil formation, and second, by the growth of forests surrounding the sands, which decreases the wind force. The restoration studies revealed differences in the geodiversity between and within the drift sand areas. Whereas the drift sands on geological and soil maps show as almost homogenous areas, they have in fact highly variable geo-conditions of which examples will be given. These geodiversity aspects concern differences in geomorphological structure, origin, sediments and age of the drift sands. Differences in wind and water erosion, trampling and soil formation add to the geodiversity within the drift sand areas. Especially in the primary stages of succession the differences in geodiversity are relevant for the Natura-2000 values. We discerned three main types of active sands. Firstly, the impressive drift sands with large parabolic dune structures, often consisting of series of interlocking parabolic dunes. They developed from the northeast towards the southwest, against the direction of the dominant wind, and must have taken centuries to develop. Small parts of these systems are still active, other parts show different degrees of soil formation. Their origin is still unclear but probably dates from medieval times (Heidinga, 1985, Jungerius & Riksen, 2008). Second are the drift sand areas with irregular hills from 0.5 to about 2

Sand transport in a two pass internal cooling duct with rib turbulators

International Nuclear Information System (INIS)

Singh, Sukhjinder; Tafti, Danesh; Reagle, Colin; Delimont, Jacob; Ng, Wing; Ekkad, Srinath

2014-01-01

Highlights: • Highest particle impingement observed in the bend and first quarter of 2nd pass. • Average particle impingement per pitch is 28% higher in the second pass. • Rib faces are by far the most susceptible to particle impingement. • Particle impingement is sensitive to particle size. • Particle impingement is sensitive to wall collision model used. - Abstract: Jet engines often operate under dirty conditions where large amounts of particulate matter can be ingested, especially, sand, ash and dirt. Particulate matter in different engine components can lead to degradation in performance. The focus of this study is to investigate the sand transport and deposition in the internal cooling passages of turbine blades. A two pass stationary square duct with rib turbulators subjected to sand ingestion is studied using Large Eddy Simulations (LES). Each pass has ribs on two opposite walls and aligned normal to the main flow direction. The rib pitch to rib height (P/e) is 9.28, the rib height to channel hydraulic diameter (e/D h ) is 0.0625 and calculations have been carried out for a bulk Reynolds number of 25,000. Particle sizes in the range 0.5–25 μm are considered, with the same size distribution as found in Arizona Road Dust (medium). Large Eddy Simulation (LES) with a wall-model is used to model the flow and sand particles are modeled using a discrete Lagrangian framework. Results quantify the distribution of particle impingement density on all surfaces. Highest particle impingement density is found in the first quarter section of the second pass after the 180° turn, where the recorded impingement is more than twice that of any other region. It is also found that the average particle impingement per pitch is 28% higher in the second pass than the first pass. Results show lower particle tendency to impact the region immediately behind the rib in the first pass compared to the second pass where particle impingement is more uniform in the region

Detection of Salmonella enterica Serovar Montevideo and Newport in Free-ranging Sea Turtles and Beach Sand in the Caribbean and Persistence in Sand and Seawater Microcosms.

Science.gov (United States)

Ives, A-K; Antaki, E; Stewart, K; Francis, S; Jay-Russell, M T; Sithole, F; Kearney, M T; Griffin, M J; Soto, E

2017-09-01

Salmonellae are Gram-negative zoonotic bacteria that are frequently part of the normal reptilian gastrointestinal flora. The main objective of this project was to estimate the prevalence of non-typhoidal Salmonella enterica in the nesting and foraging populations of sea turtles on St. Kitts and in sand from known nesting beaches. Results suggest a higher prevalence of Salmonella in nesting leatherback sea turtles compared with foraging green and hawksbill sea turtles. Salmonella was cultured from 2/9 and identified by molecular diagnostic methods in 3/9 leatherback sea turtle samples. Salmonella DNA was detected in one hawksbill turtle, but viable isolates were not recovered from any hawksbill sea turtles. No Salmonella was detected in green sea turtles. In samples collected from nesting beaches, Salmonella was only recovered from a single dry sand sample. All recovered isolates were positive for the wzx gene, consistent with the O:7 serogroup. Further serotyping characterized serovars Montevideo and Newport present in cloacal and sand samples. Repetitive-element palindromic PCR (rep-PCR) fingerprint analysis and pulsed-field gel electrophoresis of the 2014 isolates from turtles and sand as well as archived Salmonella isolates recovered from leatherback sea turtles in 2012 and 2013, identified two distinct genotypes and four different pulsotypes, respectively. The genotyping and serotyping were directly correlated. To determine the persistence of representative strains of each serotype/genotype in these environments, laboratory-controlled microcosm studies were performed in water and sand (dry and wet) incubated at 25 or 35°C. Isolates persisted for at least 32 days in most microcosms, although there were significant decreases in culturable bacteria in several microcosms, with the greatest reduction in dry sand incubated at 35°C. This information provides a better understanding of the epizootiology of Salmonella in free-ranging marine reptiles and the potential

Avalanches of Singing Sand in the Laboratory

Science.gov (United States)

Dagois-Bohy, Simon; Courrech Du Pont, Sylvain; Douady, Stéphane

2011-03-01

The song of dunes is a natural phenomenon that has arisen travellers' curiosity for a long time, from Marco Polo to R.A. Bagnold. Scientific observations in the XXth century have shown that the sound is emitted during a shear flow of these particular grains, the free surface of the flow having coherent vibrations like a loud speaker. The sound emission is also submitted to a threshold effect with many parameters like humidity, flow speed, surface of the grains. The sound has been reproduced in laboratory avalanche experiments close to the natural phenomenon on field, but set in a channel with a hard bottom and a few centimeters of sand flowing, which contradicts explanations of the sound that involve a sand dune under the avalanche flow. Flow rates measurements also show the presence of a plug region in the flow above the sheared band, with the same characteristic length as the coherence zones of the sound. Finally we show experimentally that the Froude number, once modified to take into account the height of this plug band, is the parameter that sets the amplitude of the sound, and produces a threshold that depends on the grain type.

Experimental investigation of sanding propensity for the Andrew completion

Energy Technology Data Exchange (ETDEWEB)

Venkitaraman, A.; Li, H. [Schlumberger Perforating and Testing Center (United Kingdom); Leonard, A. J.; Bowden, P. R. [BP Exploration (United Kingdom)

1998-12-31

A series of laboratory experiments were performed on three reservoir core samples selected from two plot wells to confirm the likelihood of sand production during the completion phase of the planned Andrew horizontal wells, and to perform risk analysis of formation failure at the time of underbalance perforation, and expected producing conditions. CT scans revealed no perforation failure, and the core samples did not show any propensity to produce sand during single-phase oil flow. Transient sand production was observed when water cut was introduced, but sand production declined as the percentage of water cut was increased. There was no evidence of sand production in the core samples during depletion testing either, and the wells were subsequently completed with perforated cemented liners without sand control. No sand problems have been encountered in two years of production, with some wells in water cut and declined reservoir pressure of 200 psi. 8 refs., 3 tabs., 5 figs.

Evaluation of wettability of binders used in moulding sands

Directory of Open Access Journals (Sweden)

Hutera B.

2007-01-01

Full Text Available Binders used in moulding sand have the differential properties. One of the main parameters influencing on moulding sand properties is wettability of the sand grain by binding material. In the article some problems concerned with wettability evaluation have been presented and the importance of this parameter for quantity description of process occurring in system: binder- sand grain has been mentioned. The procedure of wetting angle measurement and operation of prototype apparatus for wettability investigation of different binders used in moulding sand have been described, as well as the results of wetting angle measurement for different binders at different conditions. The addition of little amount of proper diluent to binder results in the state of equilibrium reached almost immediately. Such addition can also reduce the value of equilibrium contact angle. The uniform distribution of binder on the surface of the sand grains and reducing of the required mixing time can be obtained. It has also a positive effect on the moulding sand strength.

Nuclear energy in the oils sands

International Nuclear Information System (INIS)

Arsenault, J.E.

2014-01-01

The major Canadian oil sands are located in Alberta and Saskatchewan, with most production from the strata along the Athabasca River in Alberta. The economically recoverable oil sands reserves are estimated to be 168 billion barrels which at a current production rate of 1.8 million barrels per day (2012), are projected to last a very long time. Canada has been blessed with vast energy resources which make it potentially energy-independent and able to provide significant exports but there are concerns that their development cannot be managed in a wholly acceptable manner. Comparable concerns have been applied to nuclear energy in the past and in recent times to the oil sands. The technologies associated with these energy sources have always been controversial because they are at the confluence of economics and politics where finding a balance between risk and reward is difficult. So it should be no surprise that when these technologies get linked together in certain proposals their prospect for success is doubly difficult. The possible use of nuclear energy for production of oil from the oil sands dates back to the late 1950s, when an experiment to mine the oil by detonating an underground nuclear device was proposed. It was predicted that the heat and pressure released from such a device would create a large cavern into which oil would flow, and from where it would be pumped to the surface. Almost at the same time, oil sands research using conventional sources of energy had culminated with the development of practical refining processes, essentially those still in use today. These methods require large amounts of heat energy in the form of hot water and steam. In this century nuclear energy was proposed as the source for the heat required by the oil sands production processes. To date neither of these nuclear proposals for oil sands projects have been successful, because the economic and political balance could not be struck. (author)

The provenance of Taklamakan desert sand

Science.gov (United States)

Rittner, Martin; Vermeesch, Pieter; Carter, Andrew; Bird, Anna; Stevens, Thomas; Garzanti, Eduardo; Andò, Sergio; Vezzoli, Giovanni; Dutt, Ripul; Xu, Zhiwei; Lu, Huayu

2016-03-01

Sand migration in the vast Taklamakan desert within the Tarim Basin (Xinjiang Uyghur Autonomous region, PR China) is governed by two competing transport agents: wind and water, which work in diametrically opposed directions. Net aeolian transport is from northeast to south, while fluvial transport occurs from the south to the north and then west to east at the northern rim, due to a gradual northward slope of the underlying topography. We here present the first comprehensive provenance study of Taklamakan desert sand with the aim to characterise the interplay of these two transport mechanisms and their roles in the formation of the sand sea, and to consider the potential of the Tarim Basin as a contributing source to the Chinese Loess Plateau (CLP). Our dataset comprises 39 aeolian and fluvial samples, which were characterised by detrital-zircon U-Pb geochronology, heavy-mineral, and bulk-petrography analyses. Although the inter-sample differences of all three datasets are subtle, a multivariate statistical analysis using multidimensional scaling (MDS) clearly shows that Tarim desert sand is most similar in composition to rivers draining the Kunlun Shan (south) and the Pamirs (west), and is distinctly different from sediment sources in the Tian Shan (north). A small set of samples from the Junggar Basin (north of the Tian Shan) yields different detrital compositions and age spectra than anywhere in the Tarim Basin, indicating that aeolian sediment exchange between the two basins is minimal. Although river transport dominates delivery of sand into the Tarim Basin, wind remobilises and reworks the sediment in the central sand sea. Characteristic signatures of main rivers can be traced from entrance into the basin to the terminus of the Tarim River, and those crossing the desert from the south to north can seasonally bypass sediment through the sand sea. Smaller ephemeral rivers from the Kunlun Shan end in the desert and discharge their sediment there. Both river run

Nuclear energy in the oils sands

Energy Technology Data Exchange (ETDEWEB)

Arsenault, J.E.

2014-09-15

The major Canadian oil sands are located in Alberta and Saskatchewan, with most production from the strata along the Athabasca River in Alberta. The economically recoverable oil sands reserves are estimated to be 168 billion barrels which at a current production rate of 1.8 million barrels per day (2012), are projected to last a very long time. Canada has been blessed with vast energy resources which make it potentially energy-independent and able to provide significant exports but there are concerns that their development cannot be managed in a wholly acceptable manner. Comparable concerns have been applied to nuclear energy in the past and in recent times to the oil sands. The technologies associated with these energy sources have always been controversial because they are at the confluence of economics and politics where finding a balance between risk and reward is difficult. So it should be no surprise that when these technologies get linked together in certain proposals their prospect for success is doubly difficult. The possible use of nuclear energy for production of oil from the oil sands dates back to the late 1950s, when an experiment to mine the oil by detonating an underground nuclear device was proposed. It was predicted that the heat and pressure released from such a device would create a large cavern into which oil would flow, and from where it would be pumped to the surface. Almost at the same time, oil sands research using conventional sources of energy had culminated with the development of practical refining processes, essentially those still in use today. These methods require large amounts of heat energy in the form of hot water and steam. In this century nuclear energy was proposed as the source for the heat required by the oil sands production processes. To date neither of these nuclear proposals for oil sands projects have been successful, because the economic and political balance could not be struck. (author)

Sediment Source Fingerprinting of the Lake Urmia Sand Dunes.

Science.gov (United States)

Ahmady-Birgani, Hesam; Agahi, Edris; Ahmadi, Seyed Javad; Erfanian, Mahdi

2018-01-09

Aeolian sand dunes are continuously being discovered in inner dry lands and coastal areas, most of which have been formed over the Last Glacial Maximum. Presently, due to some natural and anthropogenic implications on earth, newly-born sand dunes are quickly emerging. Lake Urmia, the world's second largest permanent hypersaline lake, has started shrinking, vast lands comprising sand dunes over the western shore of the lake have appeared and one question has been playing on the minds of nearby dwellers: where are these sand dunes coming from, What there was not 15 years ago!! In the present study, the determination of the source of the Lake Urmia sand dunes in terms of the quantifying relative contribution of each upstream geomorphological/lithological unit has been performed using geochemical fingerprinting techniques. The findings demonstrate that the alluvial and the fluvial sediments of the western upstream catchment have been transported by water erosion and they accumulated in the lower reaches of the Kahriz River. Wind erosion, as a secondary agent, have carried the aeolian sand-sized sediments to the sand dune area. Hence, the Lake Urmia sand dunes have been originating from simultaneous and joint actions of alluvial, fluvial and aeolian processes.

Episodes of aeolian sand movement on a large spit system (Skagen Odde, Denmark) and North Atlantic storminess during the Little Ice Age

DEFF Research Database (Denmark)

Clemmensen, Lars B.; Glad, Aslaug C.; Hansen, Kristian W. T.

2015-01-01

. A change in the atmospheric circulation, so that both the North Atlantic Oscillation (NAO) and the Atlantic Multidecadal Oscillation (AMO) were negative, apparently led to an increased number of intense cyclones causing inland sand movement and dune building. The second and third phase of aeolian sand...

Maturation, fecundity, and intertidal spawning of Pacific sand lance in the northern Gulf of Alaska

Science.gov (United States)

Robards, Martin D.; Piatt, John F.; Rose, G.A.

1999-01-01

Pacific sand lance Ammodytes hexapterus in Kachemak Bay, Alaska, showed no sexual dimorphism in length-to-weight (gonad-free) ratio or length-at-age relationship. Most matured in their second year, males earlier in the season than females, but females (31%) attained a higher gonadosomatic index than males (21%). Sand lance spawned intertidally once each year in late September and October on fine gravel or sandy beaches soon after the seasonal peak in water temperatures. Sand lance in Cook Inlet and Prince William Sound displayed similar maturation schedules. Schools were dominated 2: 1 by males as they approached the intertidal zone at a site where spawning has taken place for decades. Sand lance spawned vigorously in dense formations, leaving scoured pits in beach sediments. Fecundity of females (93–199 mm) was proportional to length, ranging from 1468 to 16 081 ova per female. About half of the overall spawning school fecundity was derived from age group 1 females (55% of the school by number). Spawned eggs were 1·02 mm in diameter, demersal, slightly adhesive, and deposited in the intertidal just below the waterline. Sand lance embryos developed over 67 days through periods of intertidal exposure and sub-freezing air temperatures.

Geochemical characteristics of oil sands fluid petroleum coke

International Nuclear Information System (INIS)

Nesbitt, Jake A.; Lindsay, Matthew B.J.; Chen, Ning

2017-01-01

The geochemical characteristics of fluid petroleum coke from the Athabasca Oil Sands Region (AOSR) of northern Alberta, Canada were investigated. Continuous core samples were collected to 8 m below surface at several locations (n = 12) from three coke deposits at an active oil sands mine. Bulk elemental analyses revealed the coke composition was dominated by C (84.2 ± 2.3 wt%) and S (6.99 ± 0.26 wt%). Silicon (9210 ± 3000 mg kg"−"1), Al (5980 ± 1200 mg kg"−"1), Fe (4760 ± 1200 mg kg"−"1), and Ti (1380 ± 430 mg kg"−"1) were present in lesser amounts. Vanadium (1280 ± 120 mg kg"−"1) and Ni (230 ± 80 mg kg"−"1) exhibited the highest concentrations among potentially-hazardous minor and trace elements. Sequential extractions revealed potential for release of these metals under field-relevant conditions. Synchrotron powder X-ray diffraction revealed the presence of Si and Ti oxides, organically-complexed V and hydrated Ni sulfate, and provided information about the asphaltenic carbon matrix. X-ray absorption near edge structure (XANES) spectroscopy at the V and Ni K-edges revealed that these metals were largely hosted in porphyrins and similar organic complexes throughout coke grains. Minor differences among measured V and Ni K-edge spectra were largely attributed to slight variations in local coordination of V(IV) and Ni(II) within these organic compounds. However, linear combination fits were improved by including reference spectra for inorganic phases with octahedrally-coordinated V(III) and Ni(II). Sulfur and Fe K-edge XANES confirmed that thiophenic coordination and pyritic-ilmenitic coordination are predominant, respectively. These results provide new information on the geochemical and mineralogical composition of oil sands fluid petroleum coke and improve understanding of potential controls on associated water chemistry. - Highlights: • Oil sands fluid petroleum coke contains wide range of major, minor and

Production of Natural Gas and Fluid Flow in Tight Sand Reservoirs

Energy Technology Data Exchange (ETDEWEB)

Maria Cecilia Bravo

2006-06-30

This document reports progress of this research effort in identifying relationships and defining dependencies between macroscopic reservoir parameters strongly affected by microscopic flow dynamics and production well performance in tight gas sand reservoirs. These dependencies are investigated by identifying the main transport mechanisms at the pore scale that should affect fluids flow at the reservoir scale. A critical review of commercial reservoir simulators, used to predict tight sand gas reservoir, revealed that many are poor when used to model fluid flow through tight reservoirs. Conventional simulators ignore altogether or model incorrectly certain phenomena such as, Knudsen diffusion, electro-kinetic effects, ordinary diffusion mechanisms and water vaporization. We studied the effect of Knudsen's number in Klinkenberg's equation and evaluated the effect of different flow regimes on Klinkenberg's parameter b. We developed a model capable of explaining the pressure dependence of this parameter that has been experimentally observed, but not explained in the conventional formalisms. We demonstrated the relevance of this, so far ignored effect, in tight sands reservoir modeling. A 2-D numerical simulator based on equations that capture the above mentioned phenomena was developed. Dynamic implications of new equations are comprehensively discussed in our work and their relative contribution to the flow rate is evaluated. We performed several simulation sensitivity studies that evidenced that, in general terms, our formalism should be implemented in order to get more reliable tight sands gas reservoirs' predictions.

Electromyographic study of the upper extremity during bilateral sanding: unresisted and resisted conditions.

Science.gov (United States)

Spaulding, S J; Robinson, K L

1984-04-01

Electromyographic information was obtained from seven right shoulder complex muscles in nine subjects (three normal, three paraplegic, and three quadriplegic) during the occupational therapy activity of bilateral sanding on an incline board, an activity that has been recommended as a treatment modality to strengthen the triceps brachii. Electromyography revealed that the anterior and middle portions of the deltoid were the muscles most responsible for the subjects' arm movements during both resisted and unresisted bilateral sanding . Triceps lateralis and medialis were also active during the up phase, but not as consistently as the deltoid. Pectoralis major and biceps brachii were not extensively active in most subjects. The small size and heterogeneity of the subject sample limits the generalizations of our findings. However, graded resisted bilateral sanding does appear to be an appropriate activity for strengthening the shoulder muscle group, especially the deltoid and triceps brachii, in the tested patient populations.

Changes in active eolian sand at northern Coachella Valley, California

Science.gov (United States)

Katra, Itzhak; Scheidt, Stephen; Lancaster, Nicholas

2009-04-01

Climate variability and rapid urbanization have influenced the sand environments in the northern Coachella Valley throughout the late 20th century. This paper addresses changes in the spatial relationships among different sand deposits at northern Coachella Valley between two recent time periods by using satellite data acquired from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER). The approach employed here, involving multispectral thermal infrared (TIR) data and spectral mixture analysis, has shown that the major sand deposits can be spatially modeled at northern Coachella Valley. The "coarse-grained (quartz-rich) sand" deposit is associated with active eolian sand, and the "mixed sandy soil" and "fine-grained (quartz-rich) sand" deposits are associated with inactive eolian sand. The fractional abundance images showed a significant decrease between 2000 and 2006 in the percentage of active sand in the major depositional area for fluvial sediment, the Whitewater River, but also in two downwind areas: the Whitewater and Willow Hole Reserves. The pattern of the active sand appears to be related to variations in annual precipitation (wet and dry years) and river discharge in the northern Coachella Valley. We suggest here that recent human modifications to the major watercourses that supply sand affect the capability of fluvial deposition areas to restore sediments over time and consequently the responses of the sand transport system to climate change, becoming more sensitive to dry years where areas of active sand may shrink, degrade, and/or stabilize faster. The approach utilized in this study can be advantageous for future monitoring of sand in the northern Coachella Valley for management of these and similar environments.

Namibia : triaxial test on sand

DEFF Research Database (Denmark)

Steenfelt, Jørgen S.; Jacobsen, Kim P.

In connection with a harbour project the friction angle of a fine sand is required. On Friday 13 March 1998 the Danish Geotechnical Institute (DGI) delivered app. 2.5 kg sand for testing at the Geotechnical Engineering Laboratory, Aalborg University. The present Data Report summarises the results...... of two CID, isotropically consolidated, drained triaxial tests carried out according to the instructions in DG1 letter dated 13 March 1998....

Pattern formation - Instabilities in sand ripples

DEFF Research Database (Denmark)

Hansen, J. L.; v. Hecke, M.; Haaning, A.

2001-01-01

Sand ripples are seen below shallow wavy water and are formed whenever water oscillates over a bed of sand. Here we analyse the instabilities that can upset this perfect patterning when the ripples are subjected to large changes in driving amplitude or frequency, causing them to deform both...

Southeast Florida Sediment Assessment and Needs Determination (SAND) Study

Science.gov (United States)

2014-09-01

sand with some shell beds, sandstone , and limestone *Miami Limestone 0 to 80 ft Oolitic limestone, quartz sand, and sandstone Anastasia 0 to 100 ft...Sand, shell beds, marl, calcareous sandstone (coquina/calcarenite) Fort Thompson 0 to 80 ft Silty limestone, silty sand, clayey marl, shell marl...highly- to moderately- weathered quartzose sandstone , and highly-weathered (saprolitic) to moderately-weathered hard limestone. North-south and

Modelling the behavior of an oil saturated sand

International Nuclear Information System (INIS)

Evgin, E.; Altaee, A.; Lord, S.; Konuk, I.

1990-01-01

The experiments carried out in an earlier study show the oil contamination affects the strength and deformation characteristics of a crushed quartz sand. In the present study, a mathematical soil model is used to simulate the mechanical behavior of the same sand. The model parameters are determined for both clean and oil contaminated soil. Simulations are made for the stress-strain behavior of the soil in drained and undrained conventional traixial compression tests. In order to illustrate the effect of changes in the soil properties on the behavior of an engineering structure, a finite element analysis is carried out. In this paper comparative results are presented to show the differences in the behavior of a foundation resting on a clean sand, on an oil contaminated sand, and on a sand contaminated locally

16 CFR 313.12 - Limits on sharing account number information for marketing purposes.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Limits on sharing account number information... REGULATIONS UNDER SPECIFIC ACTS OF CONGRESS PRIVACY OF CONSUMER FINANCIAL INFORMATION Limits on Disclosures § 313.12 Limits on sharing account number information for marketing purposes. (a) General prohibition on...

12 CFR 40.12 - Limits on sharing account number information for marketing purposes.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Limits on sharing account number information... OF THE TREASURY PRIVACY OF CONSUMER FINANCIAL INFORMATION Limits on Disclosures § 40.12 Limits on sharing account number information for marketing purposes. (a) General prohibition on disclosure of...

Oblique second-order sand transport pathways on an intertidal sand flat in a natural tidal inlet system

DEFF Research Database (Denmark)

Ernstsen, Verner Brandbyge; Lefebvre, Alice; Kroon, Aart

2013-01-01

tide, sand is transported along ESE-oriented pathways across the intertidal flat towards the inner tidal basin. During the late stages of ebb tide, sand is transported in drainage channels (WSWoriented) from the intertidal flat towards the inlet channel. During storm events with winds from SW, wave...

Gasification of oil sand coke: review

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E. [IMAF Group, Ottawa, ON (Canada)

1998-08-01

The production of synthetic crude from the tar sands in Western Canada has been steadily increasing. Most of the delayed coke produced by Suncor is combusted on site, whereas all fluid coke produced by Syncrude is stockpiled.The database on the chemical and physical properties of the oil sand coke, including the composition and fusion properties of the mineral matter, has been established. The reactivity of the coke was determined by oxygen chemisorption, fixed bed and fluid bed bench scale gasification and pilot plant gasification. The reactivity of the oil sand coke for gasification is rather low and comparable to high rank coals, such as anthracite. Slurrability tests revealed that a solid concentration in water, approaching 70 wt%, can be achieved. Gasification is the front runner among clean technologies for the conversion of carbonaceous solids to useful products. Several commercial gasifiers are available to cover the wide range of severity. Because of the low reactivity of oil sands coke, high severity conditions are required to achieve high gasification conversion. Such conditions can be attained in entrained bed gasifiers. Gasifiers employing both dry and slurry feeding systems are suitable. A high efficiency, low SO{sub x} and NO{sub x} emissions, as well as a low solid waste production are among the key advantages of the gasification technology compared with thecompeting technologies. Commercial gasification of oil sands coke is delayed because of the availability of natural gas on the site of the upgrading plants. Potential for the transportation of the oil sand coke to USA for electricity generation using the integrated gasification combined-cycle (IGCC) technology was evaluated. 27 refs., 17 figs., 9 tabs.

Reuse of waste cutting sand at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Mathews, S.; Wilson, K.

1998-01-01

Lawrence Livermore National Laboratory (LLNL) examined the waste stream from a water jet cutting operation, to evaluate the possible reuse of waste garnet sand. The sand is a cutting agent used to shape a variety of materials, including metals. Nearly 70,000 pounds of waste sand is generated annually by the cutting operation. The Environmental Protection Department evaluated two potential reuses for the spent garnet sand: backfill in utility trenches; and as a concrete constituent. In both applications, garnet waste would replace the sand formerly purchased by LLNL for these purposes. Findings supported the reuse of waste garnet sand in concrete, but disqualified its proposed application as trench backfill. Waste sand stabilized in a concrete matrix appeared to present no metals-leaching hazard; however, unconsolidated sand in trenches could potentially leach metals in concentrations high enough to threaten ground water quality. A technical report submitted to the San Francisco Bay Regional Water Quality Control Board was reviewed and accepted by that body. Reuse of waste garnet cutting sand as a constituent in concrete poured to form walkways and patios at LLNL was approved

Augmenting Sand Simulation Environments through Subdivision and Particle Refinement

Science.gov (United States)

Clothier, M.; Bailey, M.

2012-12-01

Recent advances in computer graphics and parallel processing hardware have provided disciplines with new methods to evaluate and visualize data. These advances have proven useful for earth and planetary scientists as many researchers are using this hardware to process large amounts of data for analysis. As such, this has provided opportunities for collaboration between computer graphics and the earth sciences. Through collaboration with the Oregon Space Grant and IGERT Ecosystem Informatics programs, we are investigating techniques for simulating the behavior of sand. We are also collaborating with the Jet Propulsion Laboratory's (JPL) DARTS Lab to exchange ideas and gain feedback on our research. The DARTS Lab specializes in simulation of planetary vehicles, such as the Mars rovers. Their simulations utilize a virtual "sand box" to test how a planetary vehicle responds to different environments. Our research builds upon this idea to create a sand simulation framework so that planetary environments, such as the harsh, sandy regions on Mars, are more fully realized. More specifically, we are focusing our research on the interaction between a planetary vehicle, such as a rover, and the sand beneath it, providing further insight into its performance. Unfortunately, this can be a computationally complex problem, especially if trying to represent the enormous quantities of sand particles interacting with each other. However, through the use of high-performance computing, we have developed a technique to subdivide areas of actively participating sand regions across a large landscape. Similar to a Level of Detail (LOD) technique, we only subdivide regions of a landscape where sand particles are actively participating with another object. While the sand is within this subdivision window and moves closer to the surface of the interacting object, the sand region subdivides into smaller regions until individual sand particles are left at the surface. As an example, let's say

Autism: General Information. Fact Sheet Number 1 = Autismo: Informacion General. Fact Sheet Number 22.

Science.gov (United States)

Interstate Research Associates, McLean, VA.

This fact sheet on autism is offered in both English and Spanish, and is the same in both languages although numbered differently. It provides a definition, information on incidence, typical characteristics, and educational implications. It notes that autism is listed as a separate category under the Individuals with Disabilities Education Act.…

12 CFR 216.12 - Limits on sharing account number information for marketing purposes.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 2 2010-01-01 2010-01-01 false Limits on sharing account number information... GOVERNORS OF THE FEDERAL RESERVE SYSTEM PRIVACY OF CONSUMER FINANCIAL INFORMATION (REGULATION P) Limits on Disclosures § 216.12 Limits on sharing account number information for marketing purposes. (a) General...

12 CFR 573.12 - Limits on sharing account number information for marketing purposes.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Limits on sharing account number information..., DEPARTMENT OF THE TREASURY PRIVACY OF CONSUMER FINANCIAL INFORMATION Limits on Disclosures § 573.12 Limits on sharing account number information for marketing purposes. (a) General prohibition on disclosure of...

12 CFR 332.12 - Limits on sharing account number information for marketing purposes.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Limits on sharing account number information... REGULATIONS AND STATEMENTS OF GENERAL POLICY PRIVACY OF CONSUMER FINANCIAL INFORMATION Limits on Disclosures § 332.12 Limits on sharing account number information for marketing purposes. (a) General prohibition on...

Understanding Colombian Amazonian white sand forests

NARCIS (Netherlands)

Peñuela-Mora, M.C.

2014-01-01

Although progress has been made in studies on white sand forests in the Amazon, there is still a considerable gap in our knowledge of the unique species composition of white sand forests and their structure and dynamics, especially in Western Amazon. This thesis aims to fill this gap by addressing

Predictors for the Number of Warning Information Sources During Tornadoes.

Science.gov (United States)

Cong, Zhen; Luo, Jianjun; Liang, Daan; Nejat, Ali

2017-04-01

People may receive tornado warnings from multiple information sources, but little is known about factors that affect the number of warning information sources (WISs). This study examined predictors for the number of WISs with a telephone survey on randomly sampled residents in Tuscaloosa, Alabama, and Joplin, Missouri, approximately 1 year after both cities were struck by violent tornadoes (EF4 and EF5) in 2011. The survey included 1006 finished interviews and the working sample included 903 respondents. Poisson regression and Zero-Inflated Poisson regression showed that older age and having an emergency plan predicted more WISs in both cities. Education, marital status, and gender affected the possibilities of receiving warnings and the number of WISs either in Joplin or in Tuscaloosa. The findings suggest that social disparity affects the access to warnings not only with respect to the likelihood of receiving any warnings but also with respect to the number of WISs. In addition, historical and social contexts are important for examining predictors for the number of WISs. We recommend that the number of WISs should be regarded as an important measure to evaluate access to warnings in addition to the likelihood of receiving warnings. (Disaster Med Public Health Preparedness. 2017;11:168-172).

Shoalwater-Byfield: national estate built on sand

International Nuclear Information System (INIS)

Lindsey, R.

1991-01-01

The Federal Government's decision to allow sand mining at Shoalwater is strongly condemned. According to the CSIRO, local, state and national conservation groups, the Environmental Impact Statement (ESI) recently released does not provide an adequate and reliable basis for the assessment of the environmental impact. It is recommended that an independent scientific agency, such as CSIRO, carry out an extensive faunal and floral survey of the area, to provide publicly accessible information on its natural values and a baseline for meaningful environmental planning for the area as a hole. ills

Trajectories of saltating sand particles behind a porous fence

Science.gov (United States)

Zhang, Ning; Lee, Sang Joon; Chen, Ting-Guo

2015-01-01

Trajectories of aeolian sand particles behind a porous wind fence embedded in a simulated atmospheric boundary layer were visualized experimentally, to investigate the shelter effect of the fence on sand saltation. Two sand samples, one collected from a beach (d = 250 μm) and the other from a desert (d = 100 μm), were tested in comparison with the previous studies of a 'no-fence' case. A wind fence (ε = 38.5%) was installed on a flat sand bed filled with each sand sample. A high-speed photography technique and the particle tracking velocimetry (PTV) method were employed to reconstruct the trajectories of particles saltating behind the fence. The collision processes of these sand particles were analyzed, momentum and kinetic energy transfer between saltating particles and ground surface were also investigated. In the wake region, probability density distributions of the impact velocities agree well with the pattern of no-fence case, and can be explained by a log-normal law. The horizontal component of impact velocity for the beach sand is decreased by about 54%, and about 76% for the desert sand. Vertical restitution coefficients of bouncing particles are smaller than 1.0 due to the presence of the wind fence. The saltating particles lose a large proportion of their energy during the collision process. These results illustrate that the porous wind fence effectively abates the further evolution of saltating sand particles.

Habitat analysis of North American sand flies near veterans returning from leishmania-endemic war zones

Directory of Open Access Journals (Sweden)

Keep Lisa

2008-12-01

Full Text Available Abstract Background Nearly 1300 cases of leishmaniasis have been identified in American military personnel deployed to Iraq and Afghanistan. The symptoms of this disease can range from a mild, self-limiting cutaneous infection to a deadly visceral infection and are not prevented by chemoprophylaxis or immunization. Effective treatments, however, are available. The disease-causing parasite is spread through the bite of the female sand fly. Although the disease occurs in both the Old World and the New World, the parasite species differ between the hemispheres. The large number of cases in military veterans has caused some concern that Old World, temperate-adapted parasite species could be introduced into the native sand fly populations of American military facilities where veterans of the current conflicts return following their deployments. This paper reports part of a larger study to analyze the risk of such an accidental importation. Four potential habitats on two large Army facilities in the Southeast United States were surveyed to determine relative sand fly density. The National Land Cover Map was used to provide sand fly density prediction maps by habitat. Results Sand fly density was significantly higher in deciduous forest and even higher at the interface between forest and open grassland. The evergreen forest and agricultural fields supported very low densities. On Fort Campbell, KY, the percentage of land covered by suitable habitat was very high. A sand fly density prediction map identified large tracts of land where infected individuals would be at higher risk of exposure to sand fly bites, resulting in an increased risk of introducing the parasite to a native insect population. On Fort Bragg, NC, however, commercial farming of long leaf pine reduced the percentage of the land covered in vegetation suitable for the support of sand flies. The risk of introducing an exotic Leishmania spp. on Fort Bragg, therefore, is considered to be

Biodegradable materials as binders for IVth generation moulding sands

OpenAIRE

K. Major-Gabry

2015-01-01

This paper focuses on the possibility of using the biodegradable materials as binders (or parts of binders?compositions) for foundry moulding and core sands. Results showed that there is a great possibility of using available biodegradable materials as foundry moulding sand binders. Using biodegradable materials as partial content of new binders, or additives to moulding sands may not only decrease the toxicity and increase reclamation ability of tested moulding sands, but also accelerate the...

Information guided channel hopping with an arbitrary number of transmit antennas

KAUST Repository

Yang, Yuli; Aï ssa, Sonia

2012-01-01

In order to realize the information guided channel hopping, also known as spatial modulation, with more design flexibility, in this paper we propose a novel scheme that allows operation with an arbitrary number of transmit antennas. Once the number of transmit antennas is not a power of two, the antennas' symbols are mapped by different numbers of bits. Subsequently, constellations with different orders are exploited for the modulation of radiated symbols so as to guarantee that the total number of bits transmitted at each time slot remains the same. Furthermore, we introduce a decoding algorithm with low complexity for this design. Numerical results on bit error rate performance are provided and substantiate that the proposed scheme turns out to be a promising alternative to the design of information guided channel hopping. © 2012 IEEE.

Information guided channel hopping with an arbitrary number of transmit antennas

KAUST Repository

Yang, Yuli

2012-10-01

In order to realize the information guided channel hopping, also known as spatial modulation, with more design flexibility, in this paper we propose a novel scheme that allows operation with an arbitrary number of transmit antennas. Once the number of transmit antennas is not a power of two, the antennas\\' symbols are mapped by different numbers of bits. Subsequently, constellations with different orders are exploited for the modulation of radiated symbols so as to guarantee that the total number of bits transmitted at each time slot remains the same. Furthermore, we introduce a decoding algorithm with low complexity for this design. Numerical results on bit error rate performance are provided and substantiate that the proposed scheme turns out to be a promising alternative to the design of information guided channel hopping. © 2012 IEEE.

Application of RFLP-PCR-Based Identification for Sand Fly Surveillance in an Area Endemic for Kala-Azar in Mymensingh, Bangladesh

Directory of Open Access Journals (Sweden)

Mohammad Shafiul Alam

2012-01-01

Full Text Available Mymensingh is the most endemic district for kala-azar in Bangladesh. Phlebotomus argentipes remains the only known vector although a number of sand fly species are prevalent in this area. Genotyping of sand flies distributed in a VL endemic area was developed by a PCR and restriction-fragment-length polymorphism (RFLP of 18S rRNA gene of sand fly species. Using the RFLP-PCR analysis with AfaI and HinfI restriction enzymes, P. argentipes, P. papatasi, and Sergentomyia species could be identified. Among 1,055 female sand flies successfully analyzed for the species identification individually, 64.4% flies was classified as Sergentomyia species, whereas 35.6% was identified as P. argentipes and no P. papatasi was found. Although infection of Leishmania within the sand flies was individually examined targeting leishmanial minicircle DNA, none of the 1,055 sand flies examined were positive for Leishmania infection. The RFLP-PCR could be useful tools for taxonomic identification and Leishmania infection monitoring in endemic areas of Bangladesh.

The Canadian oil sands--a sticky future

Energy Technology Data Exchange (ETDEWEB)

Cowtan, S A

1977-01-01

The oil sands have been known for 200 yr but only over the last decade have they been recognized as a potential major energy source for Canada. The study looks at the present GCOS plant, and briefly discusses Canada's future energy requirements and how she might fill those requirements from conventional and nonconventional sources, such as the Frontier areas, oil sands mining, oil sands in situ, and heavy oil. The economics and the future of these sources and the environment necessary for their development are analyzed.

Next-Generation Sequencing Assessment of Eukaryotic Diversity in Oil Sands Tailings Ponds Sediments and Surface Water.

Science.gov (United States)

Aguilar, Maria; Richardson, Elisabeth; Tan, BoonFei; Walker, Giselle; Dunfield, Peter F; Bass, David; Nesbø, Camilla; Foght, Julia; Dacks, Joel B

2016-11-01

Tailings ponds in the Athabasca oil sands (Canada) contain fluid wastes, generated by the extraction of bitumen from oil sands ores. Although the autochthonous prokaryotic communities have been relatively well characterized, almost nothing is known about microbial eukaryotes living in the anoxic soft sediments of tailings ponds or in the thin oxic layer of water that covers them. We carried out the first next-generation sequencing study of microbial eukaryotic diversity in oil sands tailings ponds. In metagenomes prepared from tailings sediment and surface water, we detected very low numbers of sequences encoding eukaryotic small subunit ribosomal RNA representing seven major taxonomic groups of protists. We also produced and analysed three amplicon-based 18S rRNA libraries prepared from sediment samples. These revealed a more diverse set of taxa, 169 different OTUs encompassing up to eleven higher order groups of eukaryotes, according to detailed classification using homology searching and phylogenetic methods. The 10 most abundant OTUs accounted for > 90% of the total of reads, vs. large numbers of rare OTUs (< 1% abundance). Despite the anoxic and hydrocarbon-enriched nature of the environment, the tailings ponds harbour complex communities of microbial eukaryotes indicating that these organisms should be taken into account when studying the microbiology of the oil sands. © 2016 The Author(s) Journal of Eukaryotic Microbiology © 2016 International Society of Protistologists.

Thermoluminescent dosimetric properties of Descalvado sand

International Nuclear Information System (INIS)

Teixeira, M.I.; Caldas, L.V.E.

2006-01-01

Sand samples proceeding from Descalvado, Sao Paulo, were studied with regard to their dosimetric properties using the thermoluminescence technique (TL) for high doses. These sand samples present steady physical and chemical characteristics to the end items, and they are used in the glass industry and for casting. The TL curves of the samples were obtained after an irradiation at the Gamma-Cell system ( 60 Co), of IPEN. The glow curves present two peaks at 80 C and 220 C approximately. Calibration curves were obtained for doses between 50 Gy and 5 kGy. The results indicate that the sand samples can be used for high-doses dosimetry in several areas of applications of ionizing radiation. (Author)

Thermoluminescent dosimetric properties of Descalvado sand

Energy Technology Data Exchange (ETDEWEB)

Teixeira, M.I.; Caldas, L.V.E

2006-07-01

Sand samples proceeding from Descalvado, Sao Paulo, were studied with regard to their dosimetric properties using the thermoluminescence technique (TL) for high doses. These sand samples present steady physical and chemical characteristics to the end items, and they are used in the glass industry and for casting. The TL curves of the samples were obtained after an irradiation at the Gamma-Cell system ({sup 60} Co), of IPEN. The glow curves present two peaks at 80 C and 220 C approximately. Calibration curves were obtained for doses between 50 Gy and 5 kGy. The results indicate that the sand samples can be used for high-doses dosimetry in several areas of applications of ionizing radiation. (Author)

Growth and abundance of Pacific Sand Lance, Ammodytes hexapterus, under differing oceanographic regimes

Science.gov (United States)

Robards, Martin D.; Gray, Floyd; Piatt, John F.

2002-01-01

Dramatic changes in seabird and marine mammal stocks in the Gulf of Alaska have been linked to shifts in abundance and composition of forage fish stocks over the past 20 years. The relative value (e.g., size and condition of individual fish, abundance) of specific forage fish stocks to predators under temporally changing oceanographic regimes is also expected to vary. We inferred potential temporal responses in abundance, growth, and age structure of a key forage fish, sand lance, by studying across spatially different oceanographic regimes. Marked meso-scale differences in abundance, growth, and mortality existed in conjunction with these differing regimes. Growth rate within stocks (between years) was positively correlated with temperature. However, this relationship did not exist among stocks (locations) and differing growth rates were better correlated to marine productivity. Sand lance were least abundant and grew slowest at the warmest site (Chisik Island), an area of limited habitat and low food abundance. Abundance and growth of juvenile sand lance was highest at the coolest site (Barren Islands), an area of highly productive upwelled waters. Sand lance at two sites located oceanographically between the Barren Islands and Chisik Island (inner- and outer-Kachemak Bay) displayed correspondingly intermediate abundance and growth. Resident predators at these sites are presented with markedly different numbers and quality of this key prey species. Our results suggest that at the decadal scale, Gulf of Alaska forage fish such as sand lance are probably more profoundly affected by changes in abundance and quality of their planktonic food, than by temperature alone.

Mitigating in situ oil sands carbon costs

Energy Technology Data Exchange (ETDEWEB)

Theriault, D.J.; Peterson, J. [Laricina Energy Ltd., Calgary, AB (Canada); Heinrichs, H. [Canadian Chemical Technology Inc., Calgary, AB (Canada)

2008-10-15

Carbon capture and sequestration is a complex problem with a variety of dimensions that need to be considered. The political, social, and regulatory pressures are forcing carbon costs on the oil sands industry in an effort to reduce the carbon footprint of oil sands operations. This paper reviewed the political, social, and regulatory pressures and obligations for the in-situ oil sands industry. It presented the views and insights of Laricina Energy on the carbon challenge. It also described the initiatives that Laricina Energy is taking to manage these imperatives and outlined the challenges the industry is facing. The purpose of the paper was to encourage dialogue and collaboration by the oil sands industry. The paper also described the dimensions of the carbon problem and how the industry can contribute to a solution. Last, the paper reviewed the parameters of carbon dioxide or greenhouse gas containment and storage issues. It was concluded that the regulatory and policy requirements need to be clarified so that industry understands the new business landscape as well as the requirements that influence the economics of in-situ oil sands development. 7 refs., 7 figs.

Paleontological overview of oil shale and tar sands areas in Colorado, Utah, and Wyoming.

Energy Technology Data Exchange (ETDEWEB)

Murphey, P. C.; Daitch, D.; Environmental Science Division

2009-02-11

In August 2005, the U.S. Congress enacted the Energy Policy Act of 2005, Public Law 109-58. In Section 369 of this Act, also known as the ''Oil Shale, Tar Sands, and Other Strategic Unconventional Fuels Act of 2005,'' Congress declared that oil shale and tar sands (and other unconventional fuels) are strategically important domestic energy resources that should be developed to reduce the nation's growing dependence on oil from politically and economically unstable foreign sources. In addition, Congress declared that both research- and commercial-scale development of oil shale and tar sands should (1) be conducted in an environmentally sound manner using management practices that will minimize potential impacts, (2) occur with an emphasis on sustainability, and (3) benefit the United States while taking into account concerns of the affected states and communities. To support this declaration of policy, Congress directed the Secretary of the Interior to undertake a series of steps, several of which are directly related to the development of a commercial leasing program for oil shale and tar sands. One of these steps was the completion of a programmatic environmental impact statement (PEIS) to analyze the impacts of a commercial leasing program for oil shale and tar sands resources on public lands, with an emphasis on the most geologically prospective lands in Colorado, Utah, and Wyoming. For oil shale, the scope of the PEIS analysis includes public lands within the Green River, Washakie, Uinta, and Piceance Creek Basins. For tar sands, the scope includes Special Tar Sand Areas (STSAs) located in Utah. This paleontological resources overview report was prepared in support of the Oil Shale and Tar Sands Resource Management Plan Amendments to Address Land Use Allocations in Colorado, Utah, and Wyoming and PEIS, and it is intended to be used by Bureau of Land Management (BLM) regional paleontologists and field office staff to support future

Aging effects on oil-contaminated Kuwaiti sand

International Nuclear Information System (INIS)

Al-Sanad, H.A.; Ismael, N.F.

1997-01-01

Large quantities of oil-contaminated sands resulted from the destruction of oil wells and the formation of oil lakes in Kuwait at the end of the Gulf Wa/r. A laboratory testing program was carried out to determine the geotechnical properties of this material and the effect of aging on their properties. Tests included direct shear, triaxial, and consolidation tests on clean and contaminated sand at the same relative density. The influence of aging was examined by testing uncontaminated sand after aging for one, three, and six months in natural environmental conditions. The results indicated increased strength and stiffness due to aging and a reduction of the oil content due to evaporation of volatile compounds. The factors that influence the depth of oil penetration in compacted sand columns were also examined including the type of oil, relative density, and the amount of fines

Batch and column studies of adsorption of Li, Ni and Br by a reference sand for contaminant transport experiments

International Nuclear Information System (INIS)

Seigel, M.D.; Ward, D.B.; Bryan, C.R.

1995-09-01

A processed quartz sand (Wedron 510), mined from the St. Peter sandstone, has been characterized by a variety of chemical and physical methods for use as a reference porous media in transport model validation experiments. Wedron 510 sand was used in an intermediate-scale experiment involving migration of Ni, Li and Br through a 6-m high x 3-m diameter caisson. Ni and Li adsorption/desorption, and Li/Ni site-competition experiments yielded information on the importance of the trace mineral phases to adsorption of Li and Ni by the sand. The presence of an iron hydroxide coating similar to goethite on the sand grains is suggested by visual observation and leaching experiments. Kaolinite was identified by SEM and XRD as a significant trace mineral phase in the sand and occurs as small particles coating the sand grains. Quartz, the predominant constituent of the sand by weight, does not appear to contribute significantly to the adsorption properties of the sand. Qualitatively, the adsorption properties of the sand can be adequately modeled as a two-mineral system (goethite and kaolinite). The studies described in this report should provide a basis for understanding transport of Ni, Li and Br through porous media similar to the reference sand. Techniques were developed for obtaining parameter values for surface complexation and kinetic adsorption models for the sand and its mineral components. These constants can be used directly in coupled hydrogeochemical transport codes. The techniques should be useful for characterization of other natural materials and elements in high-level nuclear waste in support of coupled hydrogeochemical transport calculations for Yucca Mountain

Effectiveness of SCADA Systems in Control of Green Sands Properties

Directory of Open Access Journals (Sweden)

Ignaszak Z.

2016-03-01

Full Text Available The paper undertakes an important topic of evaluation of effectiveness of SCADA (Supervisory Control and Data Acquisition systems, used for monitoring and control of selected processing parameters of classic green sands used in foundry. Main focus was put on process studies of properties of so-called 1st generation molding sands in the respect of their preparation process. Possible methods of control of this processing are presented, with consideration of application of fresh raw materials, return sand (regenerate and water. The studies conducted in one of European foundries were aimed at pointing out how much application of new, automated plant of sand processing incorporating the SCADA systems allows stabilizing results of measurement of selected sand parameters after its mixing. The studies concerned two comparative periods of time, before an implementation of the automated devices for green sands processing (ASMS - Automatic Sand Measurement System and MCM – Main Control Module and after the implementation. Results of measurement of selected sand properties after implementation of the ASMS were also evaluated and compared with testing studies conducted periodically in laboratory.

Mass spectrometry of oil sands naphthenic acids : degradation in OSPW and wetland plants

Energy Technology Data Exchange (ETDEWEB)

Headley, J. [Environment Canada, Saskatoon, SK (Canada). Water Science and Technology Directorate

2009-07-01

This presentation discussed mass spectrometry of oil sands naphthenic acids and the degradation in OSPW and wetland plants. It presented background information on the Athabasca oil sands and naphthenic acids which involve a mixture of alkanes and cycloalkane carboxylic acids with aliphatic side chains. The presentation also discussed mass spectrometry with electrospray operating in negative ion modes. Loop injection, external standard methods and solid phase extraction were reviewed along with improved analysis by removing background ions. Other topics that were presented included hydroponic test systems and wetland plant toxicity, growth and transpiration. It was concluded that dissipation included species containing oxygen, ozone, O{sub 4}, and O{sub 5}. tabs., figs.

Study on phlebotomine sand fly (Diptera: Psychodidae fauna in Belo Horizonte, state of Minas Gerais, Brazil

Directory of Open Access Journals (Sweden)

Carina Margonari de Souza

2004-12-01

Full Text Available A study on the phlebotomine sand fly fauna in Belo Horizonte city, state of Minas Gerais, Brazil, was carried out. From April 2001 to March 2003, monthly systematic collections were performed in three houses from each of the nine regions of the city, using CDC light traps for four consecutive days. The traps were set into the houses and in peridomestic areas totaling 54 traps. A number of 3871 sand fly specimens of the genera Lutzomyia and Brumptomyia were collected. Sixty eight percent of the specimens were L. longipalpis and 16% L. whitmani, insect vectors of visceral and American cutaneous leishmaniasis, respectively. Environmental factors such as temperature, humidity, and frequency of precipitation suggest that the number of insects increases after rainy periods. During the same period mentioned above, seasonal captures were carried out in parks and green areas of Belo Horizonte, using Shannon trap. A total of 579 phlebotomine sand flies were collected from which 398 (68.7% were females with the predominance of L. whitmani and L. monticola. Those specimens were used for natural infection examination, by polymerase chain reaction. No Leishmania DNA was present in any of the specimens tested.

Effective Laboratory Method of Chromite Content Estimation in Reclaimed Sands

Directory of Open Access Journals (Sweden)

Ignaszak Z.

2016-09-01

Full Text Available The paper presents an original method of measuring the actual chromite content in the circulating moulding sand of foundry. This type of material is applied for production of moulds. This is the case of foundry which most frequently perform heavy casting in which for the construction of chemical hardening mould is used, both the quartz sand and chromite sand. After the dry reclamation of used moulding sand, both types of sands are mixed in various ratios resulting that in reclaimed sand silos, the layers of varying content of chromite in mixture are observed. For chromite recuperation from the circulating moulding sand there are applied the appropriate installations equipped with separate elements generating locally strong magnetic field. The knowledge of the current ratio of chromite and quartz sand allows to optimize the settings of installation and control of the separation efficiency. The arduous and time-consuming method of determining the content of chromite using bromoform liquid requires operational powers and precautions during using this toxic liquid. It was developed and tested the new, uncomplicated gravimetric laboratory method using powerful permanent magnets (neodymium. The method is used in the production conditions of casting for current inspection of chromite quantity in used sand in reclamation plant.

Leishmania development in sand flies: parasite-vector interactions overview.

Science.gov (United States)

Dostálová, Anna; Volf, Petr

2012-12-03

Leishmaniases are vector-borne parasitic diseases with 0.9 - 1.4 million new human cases each year worldwide. In the vectorial part of the life-cycle, Leishmania development is confined to the digestive tract. During the first few days after blood feeding, natural barriers to Leishmania development include secreted proteolytic enzymes, the peritrophic matrix surrounding the ingested blood meal and sand fly immune reactions. As the blood digestion proceeds, parasites need to bind to the midgut epithelium to avoid being excreted with the blood remnant. This binding is strictly stage-dependent as it is a property of nectomonad and leptomonad forms only. While the attachment in specific vectors (P. papatasi, P. duboscqi and P. sergenti) involves lipophosphoglycan (LPG), this Leishmania molecule is not required for parasite attachment in other sand fly species experimentally permissive for various Leishmania. During late-stage infections, large numbers of parasites accumulate in the anterior midgut and produce filamentous proteophosphoglycan creating a gel-like plug physically obstructing the gut. The parasites attached to the stomodeal valve cause damage to the chitin lining and epithelial cells of the valve, interfering with its function and facilitating reflux of parasites from the midgut. Transformation to metacyclic stages highly infective for the vertebrate host is the other prerequisite for effective transmission. Here, we review the current state of knowledge of molecular interactions occurring in all these distinct phases of parasite colonization of the sand fly gut, highlighting recent discoveries in the field.

Injury experience in sand and gravel mining, 1991

Energy Technology Data Exchange (ETDEWEB)

1993-10-01

This Mine Safety and Health Administration (MSHA) informational report reviews in detail the occupational injury and illness experience of sand and gravel mining in the United States for 1991. Data reported by operators of mining establishments concerning work injuries are summarized by work location, accident classification, part of body injured, nature of injury, and occupation. Related information on employment, worktime, and operating activity also is presented. Data reported by independent contractors performing certain work at mining locations are depicted separately in this report. For ease of comparison with other metal and nonmetallic mineral mining industries and with coal mining, summary reference tabulations are included at the end of both the operator and the contractor sections of this report.

Big picture thinking in oil sands tailings disposal

Energy Technology Data Exchange (ETDEWEB)

Boswell, J. [Thurber Engineering Ltd., Calgary, AB (Canada)

2010-07-01

This PowerPoint presentation discussed methods of disposing oil sands tailings. Oil sands operators are currently challenged by a variety of legislative and environmental factors concerning the creation and disposal of oil sands tailings. The media has focused on the negative ecological impact of oil sands production, and technical issues are reducing the effect of some mitigation processes. Operators must learn to manage the interface between tailings production and removal, the environment, and public opinion. The successful management of oil sand tailings will include procedures designed to improve reclamation processes, understand environmental laws and regulations, and ensure that the cumulative impacts of tailings are mitigated. Geotechnical investigations, engineering designs and various auditing procedures can be used to develop tailings management plans. Environmental screening and impact assessments can be used to develop sustainable solutions. Public participation and environmental mediation is needed to integrate the public, environmental and technical tailings management strategies. Operators must ensure public accountability for all stakeholders. tabs., figs.

Phenology and population dynamics of sand flies in a new focus of visceral leishmaniasis in Eastern Azarbaijan Province, North western of Iran.

Science.gov (United States)

Hazratian, Teimour; Rassi, Yavar; Oshaghi, Mohammad Ali; Yaghoobi-Ershadi, Mohammad Reza; Fallah, Esmael; Shirzadi, Mohammad Reza; Rafizadeh, Sina

2011-08-01

To investigate species composition, density, accumulated degree-day and diversity of sand flies during April to October 2010 in Azarshahr district, a new focus of visceral leishmaniasis in north western Iran. Sand flies were collected using sticky traps biweekly and were stored in 96% ethanol. All specimens were mounted in Puri's medium for species identification using valid keys of sandflies. The density was calculated by the formula: number of specimens/m(2) of sticky traps and number of specimens/number of traps. Degree-day was calculated as follows: (Maximum temperature + Minimum temperature)/2-Minimum threshold. Diversity indices of the collected sand flies within different villages were estimated by the Shannon-weaver formula ( H'=∑i=1sPilog(e)Pi). Totally 5 557 specimens comprising 16 Species (14 Phlebotomus, and 2 Sergentomyia) were indentified. The activity of the species extended from April to October. Common sand-flies in resting places were Phlebotomus papatasi, Phlebotomus sergenti and Phlebotomus mongolensis. The monthly average density was 37.6, 41.1, 40.23, 30.38 and 30.67 for Almalodash, Jaragil, Segaiesh, Amirdizaj and Germezgol villages, respectively. Accumulated degree-day from early January to late May was approximately 289 degree days. The minimum threshold temperature for calculating of accumulated degree-day was 17.32°. According on the Shannon-weaver (H'), diversity of sand flies within area study were estimated as 0.917, 1.867, 1.339, 1.673, and 1.562 in Almalodash, Jaragil, Segaiesh, Amirdizaj and Germezgol villages, respectively. This study is the first detailed research in terms of species composition, density, accumulated degree-day and diversity of sand flies in an endemic focus of visceral leishamaniasis in Azarshahr district. The population dynamics of sand flies in Azarshahr district were greatly affected by climatic factors. According to this study the highest activity of the collected sand fly species occurs at the teritary

77 FR 56212 - Federal Acquisition Regulation; Information Collection; Use of Data Universal Numbering System...

Science.gov (United States)

2012-09-12

...; Information Collection; Use of Data Universal Numbering System (DUNS) as Primary Contractor Identification... ``Information Collection 9000-0145, Use of Data Universal Numbering System (DUNS) as Primary Contractor... extension of a previously approved information collection requirement concerning use of the Data Universal...

Characterization of sand lenses embedded in tills

DEFF Research Database (Denmark)

Kessler, Timo Christian; Klint, K.E.S.; Nilsson, B.

2012-01-01

Tills dominate large parts of the superficial sediments on the Northern hemisphere. These glacial diamictons are extremely heterogeneous and riddled with fractures and lenses of sand or gravel. The frequency and geometry of sand lenses within tills are strongly linked to glaciodynamic processes...

Sand impaction of the small intestine in eight dogs.

Science.gov (United States)

Moles, A D; McGhite, A; Schaaf, O R; Read, R

2010-01-01

To describe signalment, clinical findings, imaging and treatment of intestinal sand impaction in the dog. Medical records of dogs with radiographic evidence of small intestinal sand impaction were reviewed. Sand impaction resulting in small intestinal obstruction was diagnosed in eight dogs. All dogs presented with signs of vomiting. Other clinical signs included anorexia, lethargy and abdominal pain. Radiographs confirmed the presence of radio-opaque material consistent with sand causing distension of the terminal small intestine in all dogs. Four dogs were treated surgically for their impaction and four dogs were managed medically. Seven of the eight dogs survived. Both medical and surgical management of intestinal sand impaction in the dog can be effective and both afford a good prognosis for recovery.

Consolidation of the formation sand by chemical methods

Directory of Open Access Journals (Sweden)

Mariana Mihočová

2006-10-01

Full Text Available The sand control by consolidation involves the process of injecting chemicals into the naturally unconsolidated formation to provide an in situ grain-to-grain cementation. The sand consolidation chemicals are available for some 30 years. Several types of consolidating material were tried. Presently available systems utilize solidified plastics to provide the cementation. These systems include phenol resin, phenol-formaldehyde, epoxy, furan and phenolic-furfuryl.The sand consolidation with the steam injection is a novel technique. This process provides a highly alkaline liquid phase and temperatures to 300 °C to geochemically create cements by interacting with the dirty sand.While the formation consolidation has widely applied, our experience has proved a high level of success.

Reuse of waste foundry sand through interaction with sodium silicate binder

International Nuclear Information System (INIS)

Souza, J.C.; Chinelatto, A.S.A.; Chinelatto, A.L.; Oliveira, I.L.

2012-01-01

Green sand molds are used in metal casting process. However, after heating, activated bentonite present in green sand lose the binding properties, and part of the foundry sand has to be discarded from the process. The ABNT NBR 15.984/2011 establishes the management of waste foundry sand (WFS) avoiding disposal in landfills. The objective of this work was to investigate the possibility of reusing the WFS from the study of their interaction with sodium silicate binder. Studies with silica sand and new green sand was performed to compare the results obtained with the WFS. The characterizations of the samples were performed by measures the compressive strength, X-ray diffraction, optical microscopy and scanning electron microscopy. The results showed that there is interaction of the sodium silicate with the WFS as well as with the silica sand and green sand. (author)

Geotechnical properties of crude oil contaminated sand

International Nuclear Information System (INIS)

Puri, V.K.; Das, B.M.; Cook, E.E.; Shin, E.C.

1994-01-01

Contamination of soil due to an oil spill influences its subsequent engineering behavior. An investigation was conducted to study the effect of crude oil contamination on compaction characteristics, shear strength, one-dimensional compression, and coefficient of permeability. Water permeability was also determined by using commercial grade motor oils as contaminants. The test results indicate that the compaction characteristics are influenced by oil contamination. The angle of internal friction of sand (based on total stress condition) decreases due to presence of oil within the pore spaces in sand. One dimensional compression characteristics of sand are significantly influenced by oil contamination resulting in a decrease in the value of constrained modulus with increase in the degree of oil contamination compared to the case of dry sand. Water permeability was observed to be a function of the initial viscosity and the degree of saturation due to the contaminating oil

Cross section library DOSCROS77 (in the SAND-II format)

International Nuclear Information System (INIS)

Zijp, W.L.; Nolthenius, H.J.; Borg, N.J.C.M. van der.

1977-08-01

The dosimetry cross section library DOSCROS77 is documented with tables, plots and cross section values averaged over a few reference spectra. This library is based on the ENDF/B-IV dosimetry file, supplemented with some other evaluations. The total number of reaction cross section sets incorporated in this library is 49 (+3 cover cross sections sets). The cross section data are available in a format which is suitable for the program SAND-II

[Preliminary Study of Lonicera hypoglauca on Germination Conditions of Sand Culture Seeds and Sterilization Method of Sand Culture Seedling Sterilization].

Science.gov (United States)

Tan, Mu-xiu; Zeng, Wen-wen; Wei, Peng-xiao; Mo, Qiao-cheng; Pu, Zu-ning; Cen, Xiu-fen; Shi, Feng-hua

2015-05-01

To explore the germination conditions of Lonicera hypoglauca sand culture seeds and the effects of sand culture seedlings sterilization. 0.1% HgCl2 with different sterilization time, different illumination time and temperature culture condition were adopted to study the germination conditions of sand culture seeds. Different sterilization treatments and different hardening-seedling days were used to test the sterilization effect of sand culture seedlings. The sterilization effect of the combination of 75% ethanol 30 s + 0.1% HgCl2 5 min on Lonicera hypoglauca seeds was the optimum,with the average pollution rate of 15.56%, and the average germination rate reached 51.11%. The combination of varied temperature-room temperature under light for 12 h/d was the best, with the average germination rate peaked at 75.49%, and the average germination potential reached 68.36%. The treatment of detergent liquor scrub-tap water wash on the part above the hypocotyl, which was sand cultured under the opening condition and had no root, showed the best sterilization effect, with the average pollution rate was zero, and the average survival rate peaked at 100.00%. The sterilization effect of sand culture seedlings, which was disinfected after cleaning by detergent liquor scrub-tap water wash after hardening-seeding for 30 days, was the best, with the average pollution rate of 50.00%, and the average survival rate of 100.00%. The best sterilization effect is the combination of 75% ethanol 30 s + 0.1% HgCl2 5 min; Lighting for 12 h/d of varied temperature-room temperature is regarded as the optimum culture condition. The treatment of detergent liquor scrub-tap water wash treatment on the part above the hypocotyl,which is sand cultured under the opening condition and had no root, shows the best sterilization effect. For the sand culture seedlings, before inoculated in subculture medium, should be hardening-seedling for some days and sterilized after detergent liquor scrub-tap water wash.

Strength and Compaction Analysis of Sand-Bentonite-Coal Ash Mixes

Science.gov (United States)

Sobti, Jaskiran; Singh, Sanjay Kumar

2017-08-01

This paper deals with the strength and compaction characteristics of sand-bentonite-coal ash mixes prepared by varying percentages of sand, bentonite and coal ash to be used in cutoff walls and as a liner or cover material in landfills. The maximum dry density (MDD) and optimum moisture content (OMC) of sand-bentonite mixes and sand-bentonite-coal ash mixes were determined by conducting the standard proctor test. Also, the strength and stiffness characteristics of soil mixes were furnished using unconfined compressive strength test. The results of the study reveal influence of varying percentages of coal ash and bentonite on the compaction characteristics of the sand-bentonite-coal ash mixes. Also, validation of a statistical analysis of the correlations between maximum dry density (MDD), optimum moisture content (OMC) and Specific Gravity (G) was done using the experimental results. The experimental results obtained for sand-bentonite, sand-bentonite-ash and coal ash-bentonite mixes very well satisfied the statistical relations between MDD, OMC and G with a maximum error in the estimate of MDD being within ±1 kN/m3. The coefficient of determination (R2) ranged from 0.95 to 0.967 in case of sand-bentonite-ash mixes. However, for sand-bentonite mixes, the R2 values are low and varied from 0.48 to 0.56.

17 CFR 248.12 - Limits on sharing account number information for marketing purposes.

Science.gov (United States)

2010-04-01

... account number information for marketing purposes. (a) General prohibition on disclosure of account... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Limits on sharing account number information for marketing purposes. 248.12 Section 248.12 Commodity and Securities Exchanges...

17 CFR 160.12 - Limits on sharing account number information for marketing purposes.

Science.gov (United States)

2010-04-01

....12 Limits on sharing account number information for marketing purposes. (a) General prohibition on... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Limits on sharing account number information for marketing purposes. 160.12 Section 160.12 Commodity and Securities Exchanges...

Effects of timber harvest on phlebotomine sand flies (Diptera: Psychodidae in a production forest: abundance of species on tree trunks and prevalence of trypanosomatids

Directory of Open Access Journals (Sweden)

Felipe Arley Costa Pessoa

2007-08-01

Full Text Available The Amazon forest is being exploited for timber production. The harvest removes trees, used by sand flies as resting sites, and decreases the canopy, used as refuges by some hosts. The present study evaluated the impact of the timber harvest, the abundance of sand flies, and their trypanosomatid infection rates before and after selective logging. The study was accomplished in terra-firme production forest in an area of timber harvest, state of Amazonas, Brazil. Sand fly catches were carried out in three areas: one before and after the timber harvest, and two control areas, a nature preservation area and a previously exploited area. The flies were caught by aspiration on tree trunks. Samples of sand flies were dissected for parasitological examination. In the site that suffered a harvest, a larger number of individuals was caught before the selective extraction of timber, showing significant difference in relation to the number of individuals and their flagellate infection rates after the logging. The other two areas did not show differences among their sand fly populations. This fact is suggestive of a fauna sensitive to the environmental alterations associated with selective logging.

Sand filter clogging by septic tank effluent.

Science.gov (United States)

Spychała, M; Błazejewski, R

2003-01-01

The aim of this study was to characterise conditions and factors affecting fine sand clogging by septic tank effluent on the basis of physical modelling. The physical model consisted of 12 sand columns dosed with sewage from one household (5 persons), preliminary treated in a septic tank. Hydraulic loadings of the sand filters were equal to 82 mm/d. The mean discharge from sand columns, measured as the effluent volume collected during 10 minutes, decreased significantly over the experiment period from 34 cm3/min in August 2000 to 20 cm3/min in August 2001 at the same temperature of about 20 degrees C. First the columns clogged almost completely after 480 days in December 2001, however six columns had remained unclogged till the end of the experiment (March 2002). The temperature had a significant impact on hydraulic conductivity. A vertical distribution of accumulated mass and biomass was investigated in partly clogged sand. Microscopic survey of the clogging layer showed a presence of live micro-organisms, residuals of dead micro-organisms, particularly pieces of small animal armour and many fibres. These particles accelerated the accumulation of solids in the upper clogging layer. The study indicated that temperature impact on the filter hydraulic conductivity was more significant for biological activity, than for sewage viscosity.

Gravel Mobility in a High Sand Content Riverbed

Science.gov (United States)

Haschenburger, J. K.

2017-12-01

In sand-gravel channels, sand may modify gravel transport by changing conditions of entrainment and promoting longer displacements or gravel may inhibit sand transport if concentrated into distinct deposits, which restrict sand supply with consequences for migrating bedform size or form. This study reports on gravel mobility in the lower San Antonio River, Texas, where gravel content in the bed material ranges from about 1% to more than 20%. Sediment transport observations were collected at three U.S. Geological Survey gauging stations by deploying a Helley-Smith sampler with a 0.2 mm mesh bag from which transport rates and mobile grain sizes were determined. The flow rates sampled translate into an annual exceedance expectation from 0.2% to 98%. Gravel transport rates are generally two orders of magnitude smaller than the rates of sand transport. However, the finest gravels are transported at rates on the same order of magnitude as the coarsest sands. At all sites, the 2 and 2.8 mm fractions are transported at the lowest flow rate sampled, suggesting mobility for at least 38% to as much as 98% of the year. Fractions as large as 8 mm are mobilized at flow rates that are expected between 25% and 53% of the year. The largest fractions captured in the sampling (16 to 32 mm) require flows closer to bankfull conditions that occur no more than 0.8% of the year. Results document that some gravel sizes can be frequently transported in low gradient riverbeds with high sand content.

Information hiding technology and application analysis based on decimal expansion of irrational numbers

Science.gov (United States)

Liu, Xiaoyong; Lu, Pei; Shao, Jianxin; Cao, Haibin; Zhu, Zhenmin

2017-10-01

In this paper, an information hiding method using decimal expansion of irrational numbers to generate random phase mask is proposed. Firstly, the decimal expansion parts of irrational numbers generate pseudo-random sequences using a new coding schemed, the irrational number and start and end bit numbers were used as keys in image information hiding. Secondly, we apply the coding schemed to the double phase encoding system, the pseudo-random sequences are taken to generate random phase masks. The mean square error is used to calculate the quality of the recovered image information. Finally, two tests had been carried out to verify the security of our method; the experimental results demonstrate that the cipher image has such features, strong robustness, key sensitivity, and resistance to brute force attack.

Sand waves on an epicontinental shelf: Northern Bering Sea

Science.gov (United States)

Field, M.E.; Nelson, C.H.; Cacchione, D.A.; Drake, D.E.

1981-01-01

Sand waves and current ripples occupy the crests and flanks of a series of large linear sand ridges (20 km ?? 5 km ?? 10 m high) lying in an open-marine setting in the northern Bering Sea. The sand wave area, which lies west of Seward Peninsula and southeast of Bering Strait, is exposed to the strong continuous flow of coastal water northward toward Bering Strait. A hierarchy of three sizes of superimposed bedforms, all facing northward, was observed in successive cruises in 1976 and 1977. Large sand waves (height 2 m; spacing 200 m) have smaller sand waves (height 1 m; spacing 20 m) lying at a small oblique angle on their stoss slopes. The smaller sand waves in turn have linguoid ripples on their stoss slopes. Repeated studies of the sand wave fields were made both years with high-resolution seismic-reflection profiles, side-scan sonographs, underwater photographs, current-meter stations, vibracores, and suspended-sediment samplers. Comparison of seismic and side-scan data collected along profile lines run both years showed changes in sand wave shape that indicate significant bedload transport within the year. Gouge marks made in sediment by keels of floating ice also showed significantly different patterns each year, further documenting modification to the bottom by sediment transport. During calm sea conditions in 1977, underwater video and camera observations showed formation and active migration of linguoid and straight-crested current ripples. Current speeds 1 m above the bottom were between 20 and 30 cm/s. Maximum current velocities and sand wave migration apparently occur when strong southwesterly winds enhance the steady northerly flow of coastal water. Many cross-stratified sand bodies in the geologic record are interpreted as having formed in a tidal- or storm-dominated setting. This study provides an example of formation and migration of large bedforms by the interaction of storms with strong uniform coastal currents in an open-marine setting. ?? 1981.

An introduction to conservation and reclamation at Alberta's mineable oil sands

Energy Technology Data Exchange (ETDEWEB)

Richens, T. [Alberta Environment, Edmonton, AB (Canada)

2009-07-01

This paper presented a balanced view of the conservation and reclamation issues and challenges facing oil sands development in Alberta. Bitumen is recovered by truck and shovel in the shallow oil sands of the Athabasca region. The deeper deposits in the Athabasca, Peace River and Cold Lake regions are accessed primarily using a system of horizontal wells and steam to extract the bitumen from the sand and pump it to the surface. Individual in-situ operations have a smaller environmental impact than mines, and do not produce tailings ponds. However, the footprint of in-situ facilities will accumulate over time because of the potential for extensive future development. The key issues facing conservation and reclamation in the mineable oil sands were discussed. Summary statistics on land disturbed and reclaimed in the region were also provided. The challenges facing reclamation activities include long timeframes; large scale, regional planning and integration; competing land use goals; revegetation; byproduct management; and tailings and process-affected water. Multi-stakeholder forums have proven to be the key to the progression of monitoring, research and development and the sharing of knowledge and information. Frameworks have been developed for the assessment of pre-disturbed and reclaimed soil capability specific to the oil sands region. Additional resources are also available, such as guidelines for the reclamation of terrestrial and wetland habitats that represent the best management practices for reclamation research in revegetation, soil salvage, stockpiling and placement, tailings reclamation, end pit lakes, wetlands and biodiversity. 16 refs., 1 fig.

Improvements in Sand Mold/Core Technology: Effects on Casting Finish

Energy Technology Data Exchange (ETDEWEB)

Prof. John J. Lannutti; Prof. Carroll E. Mobley

2005-08-30

In this study, the development and impact of density gradients on metal castings were investigated using sand molds/cores from both industry and from in-house production. In spite of the size of the castings market, almost no quantitative information about density variation within the molds/cores themselves is available. In particular, a predictive understanding of how structure and binder content/chemistry/mixing contribute to the final surface finish of these products does not exist. In this program we attempted to bridge this gap by working directly with domestic companies in examining the issues of surface finish and thermal reclamation costs resulting from the use of sand molds/cores. We show that these can be substantially reduced by the development of an in-depth understanding of density variations that correlate to surface finish. Our experimental tools and our experience with them made us uniquely qualified to achieve technical progress.

Scour at Vertical Piles in Sand-Clay Mixtures under Waves

DEFF Research Database (Denmark)

Dey, Subhasish; Helkjær, Anders; Sumer, B. Mutlu

2011-01-01

Marine sediments often contain sand-clay mixtures in widely varying proportions. This study presents the results of equilibrium scour and time variation of scour depths at circular piles embedded vertically in clay alone and sand-clay mixed beds under waves. Experiments were conducted in a wave...... flume with different proportions of sand-clay mixtures as bed sediments. Test results for the cases of steady current and sand alone under waves are used as references. The equilibrium scour depth reduces with an increase in clay proportion n (by weight) in a sand-clay mixture. Interestingly, the scour...

Frac sand in the United States: a geological and industry overview

Science.gov (United States)

Benson, Mary Ellen; Wilson, Anna B.; Bleiwas, Donald I.

2015-01-01

A new mineral rush is underway in the upper Midwest of the United States, especially in Wisconsin and Minnesota, for deposits of high-quality frac sand that the mining industry calls “Northern White” sand or “Ottawa” sand. Frac sand is a specialized type of sand that is added to fracking fluids that are injected into unconventional oil and gas wells during hydraulic fracturing (fracking or hydrofracking), a process that enhances petroleum extraction from tight (low permeability) reservoirs. Frac sand consists of natural sand grains with strict mineralogical and textural specifications that act as a proppant (keeping induced fractures open), extending the time of release and the flow rate of hydrocarbons from fractured rock surfaces in contact with the wellbore.

On shelterbelt design for combating sand invasion.

NARCIS (Netherlands)

Mohammed, A.E.; Stigter, C.J.; Adam, H.S.

1996-01-01

After a review of the scarce literature on using trees against sand encroachment, a quantitative experiment with a wide shelterbelt to combat sand invasion is reported on. Experimental work was carried out at the northwestern border of the Gezira Scheme (Sudan), an area of severe land degradation

Short Communications Sand moisture as a factor determining depth ...

African Journals Online (AJOL)

1993-11-05

Nov 5, 1993 ... The depths to which the animals burrow are, at least partly. determined by the moisture gradient in the sand. They are, however, incapable of burrowing into totally dry sand. Animals alter their position in the sand in response to changes in moisture content so as to ensure exposure to suitable conditions.

The effect of oil sands tailings pond sediments on embryo-larval walleye (Sander vitreus).

Science.gov (United States)

Raine, J C; Turcotte, D; Tumber, V; Peru, K M; Wang, Z; Yang, C; Headley, J V; Parrott, J L

2017-10-01

Walleye (Sander vitreus) are a commercially important North American fish species that inhabit the Athabasca River. This river flows through the Athabasca oil sands where natural sources of bitumen erode from the McMurray formation. Little information is available on responses of walleye embryos to oil sands tailings pond sediments in a laboratory setting. The current study describes the design and implementation of a daily-renewal bioassay to assess the potential effects of tailings pond sediments from the Athabasca oil sands area on walleye development. Developing walleye embryos were exposed to increasing concentrations of two tailings pond sediments (collected in the Athabasca oil sands area) until the completion of yolk absorption in control fish. Sediments from the tailings pond represent a mixture of polycyclic aromatic hydrocarbons (PAHs) and alkylated PAHs. During the 31 day exposure, the walleye were examined for mortalities, weight, length and developmental abnormalities to provide an initial evaluation of the effects of the oil sands tailings pond sediments. Walleye embryo survival differed between the tailings pond sediments, and survival decreased with increasing sediment concentration. Alkylated PAH content differed between the two tailings pond sediments and lower embryo survival corresponded to higher total and alkylated PAH content. Tailings pond sediment-exposed walleye exhibited a delay in development, as well as increased percentages of larvae with heart and yolk sac edema, and cranial and spinal malformations. These abnormalities in development are often associated with PAH and alkylated PAH exposure. This study provides an exposure design that can be used to assess sediment toxicity to early developmental stages of a fish species not commonly tested in the lab, and lays the groundwork for future studies with this and other difficult-to-culture species. These results offer information on the potential effects of tailings pond sediments

A risk-based approach for identifying constituents of concern in oil sands process-affected water from the Athabasca Oil Sands region.

Science.gov (United States)

McQueen, Andrew D; Kinley, Ciera M; Hendrikse, Maas; Gaspari, Daniel P; Calomeni, Alyssa J; Iwinski, Kyla J; Castle, James W; Haakensen, Monique C; Peru, Kerry M; Headley, John V; Rodgers, John H

2017-04-01

Mining leases in the Athabasca Oil Sands (AOS) region produce large volumes of oil sands process-affected water (OSPW) containing constituents that limit beneficial uses and discharge into receiving systems. The aim of this research is to identify constituents of concern (COCs) in OSPW sourced from an active settling basin with the goal of providing a sound rational for developing mitigation strategies for using constructed treatment wetlands for COCs contained in OSPW. COCs were identified through several lines of evidence: 1) chemical and physical characterization of OSPW and comparisons with numeric water quality guidelines and toxicity endpoints, 2) measuring toxicity of OSPW using a taxonomic range of sentinel organisms (i.e. fish, aquatic invertebrates, and a macrophyte), 3) conducting process-based manipulations (PBMs) of OSPW to alter toxicity and inform treatment processes, and 4) discerning potential treatment pathways to mitigate ecological risks of OSPW based on identification of COCs, toxicological analyses, and PBM results. COCs identified in OSPW included organics (naphthenic acids [NAs], oil and grease [O/G]), metals/metalloids, and suspended solids. In terms of species sensitivities to undiluted OSPW, fish ≥ aquatic invertebrates > macrophytes. Bench-scale manipulations of the organic fractions of OSPW via PBMs (i.e. H 2 O 2 +UV 254 and granular activated charcoal treatments) eliminated toxicity to Ceriodaphnia dubia (7-8 d), in terms of mortality and reproduction. Results from this study provide critical information to inform mitigation strategies using passive or semi-passive treatment processes (e.g., constructed treatment wetlands) to mitigate ecological risks of OSPW to aquatic organisms. Copyright © 2017 Elsevier Ltd. All rights reserved.

12 CFR 716.12 - Limits on sharing of account number information for marketing purposes.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Limits on sharing of account number information... REGULATIONS AFFECTING CREDIT UNIONS PRIVACY OF CONSUMER FINANCIAL INFORMATION Limits on Disclosures § 716.12 Limits on sharing of account number information for marketing purposes. (a) General prohibition on...

The extraction of bitumen from western oil sands

International Nuclear Information System (INIS)

Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1992-08-01

The University of Utah tar sand research and development program is concerned with research and development on Utah is extensive oil sands deposits. The program has been intended to develop a scientific and technological base required for eventual commercial recovery of the heavy oils from oil sands and processing these oils to produce synthetic crude oil and other products such as asphalt. The overall program is based on mining the oil sand, processing the mined sand to recover the heavy oils and upgrading them to products. Multiple deposits are being investigated since it is believed that a large scale (approximately 20,000 bbl/day) plant would require the use of resources from more than one deposit. The tasks or projects in the program are organized according to the following classification: Recovery technologies which includes thermal recovery methods, water extraction methods, and solvent extraction methods; upgrading and processing technologies which covers hydrotreating, hydrocracking, and hydropyrolysis; solvent extraction; production of specialty products; and environmental aspects of the production and processing technologies. These tasks are covered in this report

Biological control of infective larvae of Ancylostoma spp. in beach sand.

Science.gov (United States)

De Mello, Ingrid Ney Kramer; Braga, Fabio R; Monteiro, Thalita S Avelar; Freitas, Leandro G; Araujo, Juliana M; Soares, Filippe E Freitas; Araújo, Jackson V

2014-01-01

Geohelminths are parasites that stand out for their prevalence and wide distribution, depending on the soil for their transmission. The aim of this work was to evaluate the predatory capacity of the fungal isolate of the genus Duddingtonia (CG768) on third stage larvae (L3) of Ancylostoma spp. in beach sand under laboratory conditions. In the assay A five treatment groups and 1 control group were formed. The treatment groups contained 5000, 10,000, 15,000, 20,000 or 25,000 chlamydospores of the fungal isolate and 1000 Ancylostoma spp. L3 in pots containing 30g of sand. The control group (without fungus) contained only 1000 Ancylostoma spp. L3 and distilled water in pots with 30g of sand. Evidence of predatory activity was observed at the end of 15 days, where we observed the following percentages of reduction of L3: Group 1 (4.5%); Group 2 (24.5%); Group 3 (59.2%); Group 4 (58.8%); Group 5 (63%). However, difference was noted (p<0.01) only at concentrations 15,000, 20,000 and 25,000 in relation to control group. In the assay B two groups were formed in Petri dishes of 9cm in diameter containing agar water 2% medium. In the treated group, each Petri dish contained 500 Ancylostoma spp. L3 and 5g of sand containing the isolate CG 768 at a concentration of 25,000 chlamydospores/g of sand, and the control group (without fungus) contained only 500 L3. At the end of 7 days the non-predation L3 of Petri dishes using the method of Baermann were recovered. Difference (p<0.01) between groups on reducing the average number of Ancylostoma spp. L3 (percent reduction of 84%) was observed. The results of this study confirm earlier work on the efficiency of the Duddingtonia genus in the control of Ancylostoma spp. infective larvae. Copyright © 2013 Revista Iberoamericana de Micología. Published by Elsevier Espana. All rights reserved.

Water productivity analysis of sand dams irrigation farming in northern Ethiopia

Directory of Open Access Journals (Sweden)

Lorenzo Villani

2018-06-01

Full Text Available Water scarcity in drylands is the main problem that has to be tackled by farmers and practitioners that work in these areas. Climate change and increased and wealthier population are expected to put additional stress on the water resource. A large number of studies is calling to focus efforts to enhance water productivity (WP, and one of the most promising option is represented by water harvesting, the collection and storage of runoff water to be used for beneficially uses. Among the available technologies, sand dams are experiencing a renovated interest because of their relative simplicity and their potential. This research aims to deepen the knowledge about WP of water harvesting systems studying a sand dam irrigation system in Tigray, north Ethiopia, where farmers are getting used to this new technology. The research was carried out in the period March-April 2017, when farmers use sand dams water to irrigate off-season maize. We analysed a representative plot irrigated through a shallow well drilled in the sand dam aquifer, in terms of yield, Crop Water Productivity (CWP, Crop Water Productivity based on Evapotranspiration (CWP(ET and Economic Water Productivity (EWP, through field data analysis and a validated Aquacrop model. CWP(ET was found to be low (1.12 kg of grain per m3 of evapotranspired water, due by both inefficient water application and low soil fertility. Aquacrop model results showed that changing the irrigation schedule can increase CWP(ET up to 1.35 kg/m3 and EWP up to 3.94 birr/m3, but yield gap is mainly due to the low soil fertility. Interventions on soil fertility can raise yields from the original 3.3 up to 8.5 kg/ha, and thus CWP(ET and EWP up to 2.94 kg/m3 and 9.54 birr/m3 respectively. To enhance the effect of sand dams in northern Ethiopia, a set of measures, including conservation agriculture, is then proposed.

Estimating carrying capacity in a newly colonized sand fly Lutzomyia serrana (Diptera: Psychodidae).

Science.gov (United States)

Santamaría, Erika; Munstermann, Leonard E; Ferro, Cristina

2002-02-01

The phlebotomine sand fly Lutzomyia serrana (Damasceno & Arouck) was mass-reared tinder conditions of varying densities in an effort to improve colony production efficiency. To do this, the experimental carrying capacity of a standard rearing chamber was determined, i.e., the optimum population size in relation to density (individuals per unit of space). Rearing chambers of 100 cm3 were populated with 1-50 L. serrana engorged females and an equal number of males. Laboratory conditions were maintained at 23-26 degrees C and 85-95% RH. The following parameters were recorded for each experimental chamber (three replicates): (1) female mortality without oviposition, (2) number of eggs oviposited and (3) number of adults emerging from the egg cohort. Female mortality began to increase substantially in the 26-female chamber, from 5.7% to 15% and finally reaching 60.2% in the 46-50 female chambers. In the chambers containing 1-20 females, egg number and realized adult progeny increased linearly to reach an asymptote. In the 20-50 female chambers, the number of eggs ranged from 420 to 699, and adult production from 306 to 432. The optimum carrying capacity for the 100-cm3 chambers was 22 +/- 2 females. Beyond this number, auto-regulation was initiated, i.e., female mortality without oviposition increased as the number of females per chamber increased. Total number of eggs and adult production was similar in all chambers containing 20-50 females. In conclusion, for optimizing production of mass reared sand flies, determination of the carrying capacity is essential to optimize use of insectary resources, to avoid loss of valuable potentially ovipositing females, and to increase overall production efficiency.

Evaluation of sand reserves in del Plata City

International Nuclear Information System (INIS)

Loureiro, J.

2014-01-01

The purpose of this study is to evaluate the reserve of sand in the zone of del Plata city and beyond. This area is located in the S E edge of the department of San Jose near the mouth of Santa Lucia river. In this zone was identified the mantle of potentially exploitable sand which are based on their particle size, composition and depth of the limits cape. There are two powerful capes of sand separated by clay and silt

Seasonal fluctuations of phlebotomines sand fly populations ...

African Journals Online (AJOL)

An entomological survey of phlebotomine sand flies was conducted in the Moulay Yacoub province, central Morocco. An anthropic niche (Ouled Aid) and a wild niche (Zliligh) were selected. Sand flies were collected twice a month between April 2011 and March 2012, using sticky traps and CDC light traps. 3675 specimens ...

Flowability in crushed sand mortar

Directory of Open Access Journals (Sweden)

Cabrera, O. A.

2010-12-01

Full Text Available The present experimental study explored the relationship between mortar flowability and the voids content in crushed sand to determine the effect of grain shape and surface texture as well as dust content on the behaviour of fresh mortar. The findings revealed a close correlation between voids content and the volume of paste needed for mortar to begin to flow as a continuous material, mortar flowability and the water content needed to attain a given flowability. The comparison of the empirical findings to the results obtained with the Larrard (1, 2 model provided further information on the effect of sand grain morphology on fresh mortars.

En el presente trabajo se plantea un estudio experimental de la fluidez de morteros basado en el contenido de vacíos de arenas machacadas, para comprender la influencia de la forma y textura superficial de los granos de arena y del contenido de polvo de las mismas sobre el estado fresco de morteros. Los resultados muestran la estrecha relación entre el contenido de vacíos entre granos y los volúmenes de pasta necesarios para iniciar el escurrimiento como un material continuo, la fluidez de los morteros, el contenido de agua para alcanzar una determinada fluidez, etc. El comportamiento evaluado se compara con resultados obtenidos aplicando el modelo de F. de Larrard (1, 2, permitiendo de este modo obtener mayor información de la influencia de la morfología de los granos de la arena sobre el estado fresco de los morteros.

A Primer on Alberta’s Oil sands Royalties

Directory of Open Access Journals (Sweden)

Sarah Dobson

2015-12-01

Full Text Available Fulfilling its campaign promise, the new NDP government announced a review of Alberta’s royalty framework in June 2015. The province receives royalty revenue from three main sources – natural gas, crude oil, and oil sands. Since the 2009-10 fiscal year the largest contributor to Alberta’s royalty revenues has been the oil sands. If you want a sense of how important oil sands royalties have been for Alberta’s finances, consider this: In the 2014–15 fiscal year, the government collected just over $5 billion from oil sands royalties. These royalties covered over 10 per cent of the province’s operational expenses of $48.6 billion in the same fiscal year. Over the last six fiscal years the oil sands have contributed an average of 10 per cent of revenues to provincial coffers. This makes oil sands royalties the fourth largest contributor behind personal income taxes (23 per cent, federal transfers (13 per cent and corporate income taxes (11 per cent. But how many Albertans really understand how the royalty system works? What do we mean when we say “royalty”? How does the Alberta Government calculate royalties on oil sands producers? If the system is going to change, it’s important that Albertans understand how the current system works. That is what this paper is designed to do. For Albertans to properly judge the impact of new policy, they need a solid understanding of the current policy environment. We all know that oil prices have dropped and oil sands producers are losing profitability. As such, changes to the royalty system could have a deep and profound impact on the sector. Here are some of the issues this primer will study: • Pre-payout projects vs. post-payout projects, in other words, the classification of projects for royalty purposes based on whether the cumulative costs of a project exceed its cumulative revenues • Monthly payment of royalties vs. annual payment • Understanding the unit price of bitumen and how that

Sand ramps as palaeoenvironmental archives: Integrating general principles and regional contexts through reanalysis of the Klipkraal Sands, South Africa

Science.gov (United States)

Rowell, Alexandra L. K.; Thomas, David S. G.; Bailey, Richard M.; Holmes, Peter J.

2018-06-01

Sand ramps occur on a continuum of topographically-controlled landforms, ranging from purely aeolian features (climbing/falling dunes) to talus cones and alluvial fans. Sand ramps have been identified as potentially important palaeoenvironmental archives in dryland regions that possess relatively few Quaternary proxy records. Their utility however requires not only good age control of depositional phases but clear identification of process regimes, determined through morphological and sedimentological analyses, with several recent studies indicating the complexities of palaeoenvironmental interpretations and the controls of ramp development (Bateman et al., 2012; Rowell et al., 2018). Klipkraal Sands is a sand ramp on the north-eastern margin of the semi-arid Karoo that has been important for inferences of the extent of southern African Late Quaternary aeolian activity (Thomas et al., 2002). We reanalyse this feature, in the light of both its significance and other recent studies that have inferred extensive southern African LGM aeolian activity (Telfer et al., 2012, 2014). New sedimentological data and twelve OSL dates indicate the Klipkraal Sands formed episodically between 100-0.14 ka, rather than accumulating rapidly, while sedimentological data question the aeolian affinities of the bulk of the feature. Therefore, Klipkraal is reinterpreted as showing no particular affinity to the LGM, with sediments locally sourced with a significant colluvial component. Only the upper historical sediments can be clearly interpreted as aeolian deposits. A complex interplay of processes is suggested, for which a meaningful palaeoenvironmental interpretation cannot be easily defined. This implies that the local geomorphic processes and controls operating on sand ramps need to be established before they can be fully utilised as palaeoenvironmental archives, with implications for their interpretation worldwide.

Heavy mineral concentration from oil sand tailings

Energy Technology Data Exchange (ETDEWEB)

Chachula, F.; Erasmus, N. [Titanium Corp. Inc., Regina, SK (Canada)

2008-07-01

This presentation described a unique technique to recover heavy minerals contained in the froth treatment tailings produced by oil sand mining extraction operations in Fort McMurray, Alberta. In an effort to process waste material into valuable products, Titanium Corporation is developing technology to recover heavy minerals, primarily zircon, and a portion of bitumen contained in the final stage of bitumen processing. The process technology is being developed to apply to all mined oil sands operations in the Fort McMurray region. In 2004, Titanium Corporation commissioned a pilot research facility at the Saskatchewan Research Council to test dry oil sands tailings. In 2005, a bulk sampling pilot plant was connected to the fresh oil sands tailings pipeline on-site in Fort McMurray, where washed sands containing heavy minerals were processed at a pilot facility. The mineral content in both deposited tailings and fresh pipeline tailings was assessed. Analysis of fresh tailings on a daily basis identified a constant proportion of zircon and higher levels of associated bitumen compared with the material in the deposited tailings. The process flow sheet design was then modified to remove bitumen from the heavy minerals and concentrate the minerals. A newly modified flotation process was shown to be a viable processing route to recover the heavy minerals from froth treatment tailings. 8 refs., 9 tabs., 12 figs.

Riddle of the sands

Energy Technology Data Exchange (ETDEWEB)

Rolheiser, P

1998-09-01

A geological model of the Alberta landscape during the period stretching from about 110 million to 100 million years ago during the Cretaceous period when dinosaurs roamed the earth, was sketched. Today, the region contains the Cold Lake oil sands deposit. Imperial Oil began large-scale production at Cold Lake in 1985. The formations within the area are the source of almost half of Imperial Oil`s daily crude oil production and account for one in every 20 barrels of oil produced daily in Canada. The bitumen is produced using cyclic steam stimulation where steam is injected at high pressure into the underground reservoir, fracturing the sandstone and heating the bitumen it holds to thin it so that it can then flow through well bores to the surface. Conventional geological theory suggested that the Cold Lake reservoir was the remains of a prehistoric river delta. In 1994, Imperial Oil established a Cold Lake sequence stratigraphy project to verify this theory. This highly complex project involves volumes of geophysical well-log data from the 2,500 wells at Cold Lake, core samples cut from more than 600 of these wells and microscopic fossilized remains of 100-million-year-old flora extracted from the core samples, and seismic information. The interpreted data helps to create a three-dimensional model of the reservoir`s structure and help define its boundaries. Results have shown that the Cold Lake deposit was created from at least 13 intersecting river beds. Each of the rivers flowed for a few hundred thousand years and deposited sands of varying quality in different layers and patterns. The oil came about 40 million years later after the plant and animal materials containing hydrogen and carbon were broken down by heat and pressure to form oil. 1 fig.

Quality stabilisation of synthetic sand containing bentonite in process lines

OpenAIRE

A. Fedoryszyn

2010-01-01

Stabilisation of sand quality requires the monitoring and control of sand moisture contents and its other parameters at each stage of sandprocessing, i.e. during the preparation of return sand mix and rebonding processes. Stabilisation of sand quality necessitates the use of reliable control equipment and evaluation procedures. This study outlines the scope and results of research work aimed to improve the control equipment to enhance the performance of turbine mixers. The paper reviews the m...

Sand transport, erosion and granular electrification

DEFF Research Database (Denmark)

Merrison, J.P.

2012-01-01

is expanding our current understanding and outline the areas of advancement needed in the future. Presentation is made of current models for wind driven detachment/entrainment and the transport rates of sand and dust, including the effects of contact induced grain electrification. This ubiquitous phenomenon...... can affect grain transport through the generation of intense electric fields and processes of electrostatic assembly. Importantly the transport of sand is characterized by saltation, which is known to be an active process for erosion and therefore a source for dust and sand formation. Using novel...... erosion simulation techniques the link between grain transport rates and erosion rates has been quantified. Furthermore this can be linked to production rates for dust and has been associated with chemical and mineral alteration through a process of mechanical activation of fractured surfaces. This work...

Aeolian sand transport and aeolian deposits on Venus: A review

Science.gov (United States)

Kreslavsly, Mikhail A.; Bondarenko, Nataliya V.

2017-06-01

We review the current state of knowledge about aeolian sand transport and aeolian bedforms on planet Venus. This knowledge is limited by lack of observational data. Among the four planetary bodies of the Solar System with sufficient atmospheres in contact with solid surfaces, Venus has the densest atmosphere; the conditions there are transitional between those for terrestrial subaerial and subaqueous transport. The dense atmosphere causes low saltation threshold and short characteristic saltation length, and short scale length of the incipient dunes. A few lines of evidence indicate that the typical wind speeds exceed the saltation threshold; therefore, sand transport would be pervasive, if sand capable of saltation is available. Sand production on Venus is probably much slower than on the Earth; the major terrestrial sand sinks are also absent, however, lithification of sand through sintering is expected to be effective under Venus' conditions. Active transport is not detectable with the data available. Aeolian bedforms (transverse dunes) resolved in the currently available radar images occupy a tiny area on the planet; however, indirect observations suggest that small-scale unresolved aeolian bedforms are ubiquitous. Aeolian transport is probably limited by sand lithification causing shortage of saltation-capable material. Large impact events likely cause regional short-term spikes in aeolian transport by supplying a large amount of sand-size particles, as well as disintegration and activation of older indurated sand deposits. The data available are insufficient to understand whether the global aeolian sand transport occurs or not. More robust knowledge about aeolian transport on Venus is essential for future scientific exploration of the planet, in particular, for implementation and interpretation of geochemical studies of surface materials. High-resolution orbital radar imaging with local to regional coverage and desirable interferometric capabilities is the

Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources

Energy Technology Data Exchange (ETDEWEB)

Spinti, Jennifer [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Birgenheier, Lauren [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Deo, Milind [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Facelli, Julio [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Hradisky, Michal [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Kelly, Kerry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Miller, Jan [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); McLennan, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ring, Terry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ruple, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Uchitel, Kirsten [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States)

2015-09-30

This report summarizes the significant findings from the Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources program sponsored by the Department of Energy through the National Energy Technology Laboratory. There were four principle areas of research; Environmental, legal, and policy issues related to development of oil shale and oil sands resources; Economic and environmental assessment of domestic unconventional fuels industry; Basin-scale assessment of conventional and unconventional fuel development impacts; and Liquid fuel production by in situ thermal processing of oil shale Multiple research projects were conducted in each area and the results have been communicated via sponsored conferences, conference presentations, invited talks, interviews with the media, numerous topical reports, journal publications, and a book that summarizes much of the oil shale research relating to Utah’s Uinta Basin. In addition, a repository of materials related to oil shale and oil sands has been created within the University of Utah’s Institutional Repository, including the materials generated during this research program. Below is a listing of all topical and progress reports generated by this project and submitted to the Office of Science and Technical Information (OSTI). A listing of all peer-reviewed publications generated as a result of this project is included at the end of this report; Geomechanical and Fluid Transport Properties 1 (December, 2015); Validation Results for Core-Scale Oil Shale Pyrolysis (February, 2015); and Rates and Mechanisms of Oil Shale Pyrolysis: A Chemical Structure Approach (November, 2014); Policy Issues Associated With Using Simulation to Assess Environmental Impacts (November, 2014); Policy Analysis of the Canadian Oil Sands Experience (September, 2013); V-UQ of Generation 1 Simulator with AMSO Experimental Data (August, 2013); Lands with Wilderness Characteristics, Resource Management Plan Constraints, and Land Exchanges

Geomorphology and drift potential of major aeolian sand deposits in Egypt

Science.gov (United States)

Hereher, Mohamed E.

2018-03-01

Aeolian sand deposits cover a significant area of the Egyptian deserts. They are mostly found in the Western Desert and Northern Sinai. In order to understand the distribution, pattern and forms of sand dunes in these dune fields it is crucial to analyze the wind regimes throughout the sandy deserts of the country. Therefore, a set of wind data acquired from twelve meteorological stations were processed in order to determine the drift potential (DP), the resultant drift potential (RDP) and the resultant drift direction (RDD) of sand in each dune field. The study showed that the significant aeolian sand deposits occur in low-energy wind environments with the dominance of linear and transverse dunes. Regions of high-energy wind environments occur in the south of the country and exhibit evidence of deflation rather than accumulation with the occurrence of migratory crescentic dunes. Analysis of the sand drift potentials and their directions help us to interpret the formation of major sand seas in Egypt. The pattern of sand drift potential/direction suggests that the sands in these seas might be inherited from exogenous sources.

Two-fold sustainability – Adobe with sawdust as partial sand replacement

Science.gov (United States)

Jokhio, Gul A.; Syed Mohsin, Sharifah M.; Gul, Yasmeen

2018-04-01

Adobe is a material that is economic, environment friendly, and provides better indoor air quality. The material required for the preparation of adobe include clay, sand, and sometimes straw or other organic materials. These materials do not require industrial processing or transportation, however, sand mining has been recently posing a threat to the environment. Therefore, to enhance the existing sustainability of adobe, sand can be partially or fully replaced by other waste materials. This approach will not only solve the problem of excessive sand mining, it will also address the issue of waste management. Sawdust is one such waste material that can be used to partially replace sand in Adobe. This paper presents the results of compressive and flexural test carried out on Adobe samples with partial sand replacement by sawdust. The results show that about 4% sand replacement by volume produces higher compressive strength, whereas the flexural strength reduces with the use of sawdust. However, since flexural strength is not a critical property for adobe, it is concluded that replacing sand with sawdust by about 4% of volume will be beneficial.

Dynamic shear stiffness and damping ratio of marine calcareous and siliceous sands

Science.gov (United States)

Javdanian, Hamed; Jafarian, Yaser

2018-03-01

Shear stiffness and damping ratio of two marine calcareous and siliceous sands were evaluated through an experimental program. Resonant column and cyclic triaxial experiments were conducted to measure the dynamic properties of the sands in small and large shear strain amplitudes. The tests were conducted under various initial stress-density conditions. The influence of effective confining pressure on the dynamic properties of the sands was assessed and compared in a preceding paper. It was shown that the calcareous sand has higher shear stiffness and lower damping ratio in comparison to the siliceous sand. In this note, the results are presented in more details and the dynamic behavior curves of the studied sands are compared with some available models, mostly developed based on the laboratory data of siliceous sands. This comparative study reveals that the previous models predict the dynamic properties of the calcareous sand in less precision than those of the siliceous sand.

The importance of sand in the formation of avulsion channels within experimental fans that develop from sediment mixtures of mud and sand

Science.gov (United States)

Iscen, N.; Strom, K.

2017-12-01

Autogenic channel migration and avulsion has long been recognized as important drivers of alluvial fan dynamics. In the literature, several field studies have documented that the presence and the amount of sand transport through a channel is important for channel incision in alluvial fans and deltas. In our experiments, we present the general autogenic avulsion cycle of experimental alluvial fans with mixtures of cohesive sediment and sand with a range of boundary conditions, and we detail the importance of mobile sand fraction in the development of channels that lead to avulsion. Experimental observations demonstrate that new channels form at topographically low regions within the floodplain providing that sand is transported to these topographic lows due to overbank flow or levee breaching. In addition to the sediment transported from upstream, erosion of a previous deposit and an ongoing backfilling nearby are observed as the possible sources of sand getting into the ghost channels. We explore whether the presence of sand is important for channel development because it increases abrasion of the channel or because it changes the roughness characteristics of the flow. We also examine the affect of sediment and water supply change on the newly described channelization process and link distinctive channel morphologies to different stages of described channel development and the avulsion process.

Estimation of particle size distribution in Athabasca oil sands by indirect neutron activation analysis

Energy Technology Data Exchange (ETDEWEB)

Schutte, R.; Thompson, G.R.; Donkor, K.K. [New Caledonia College, Prince George, BC (Canada). Dept. of Chemistry; Duke, M.J.M. [Alberta Univ., Edmonton, AB (Canada). SLOWPOKE Nuclear Reactor Facility; Cowles, R. [Syncrude Canada, Edmonton, AB (Canada); Li, X.P.; Kratochvil, B. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemistry

1999-10-01

Knowledge concerning the particle size distribution (PSD) of oil sands is necessary for optimal extraction of bitumen from the sand, and it indicates ore quality, gives a measure of process performance during bitumen extraction, and yields information useful for tailings management. Oil sands with mainly coarse particulates are usually bitumen rich and easy to process in the conventional hot water extraction process. These ores do not require the addition of sodium hydroxide as a process aid, and tailings volumes are minimal in contrast to high fines oil sands. Compared to the methods currently in use for determining the PSD in the oil sand industry, a method is described that is rapid, simple to carry out, and does not involve the use of organic solvents with attendant disposal problems. The principle behind the method is the development of a set of correlations by applying regression analysis to a large set of PSD and elemental analysis data. Predicted PSDs compare favorably with results obtained by existing methods. Each of the three PSD methods currently in use could be simulated by the INAA method. The INAA-based model that predicts hydrometer equivalent data was only applicable above certain lower limits for the amount of the fine size fractions present because of the limited sensitivity of the hydrometer method for PSD determination of fine fractions. For all six particle sizes studied, the INAA model had lower overall uncertainty than the corresponding Microtrac and Coulter instrument methods; the instrument repeatability of the INAA fell between those of Microtrac and Coulter. For Athabasca oil sands, the INAA-based method for PSD determination at and below 44 microm afforded results comparable to current Microtrac and Coulter methods. 13 refs., 9 tabs., 2 figs.

Rheology of oil sands slurries

Energy Technology Data Exchange (ETDEWEB)

Chow, R.; Zhou, J. [Alberta Research Council, Edmonton, AB (Canada). Mineral Oil Sands Unit; Wallace, D. [Dean Wallace Consulting Inc., Beaumont, AB (Canada)

2006-07-01

This study focused on integrating rheology and colloid science to improve recovery of bitumen in surface mined oil sands. Factors that influence recovery, such as conditions of particle interaction, solids concentration and shear rate, were reviewed. In an effort to understand the rheological behaviour of clay-in-water suspensions, an elaborate procedure was developed to separate an inter-bedded clay layer from a site at Albian Sands Energy Inc. The variables were water chemistry, solids concentration, and shear rate. The research study was conducted at the Alberta Research Council with the support of the CONRAD Extraction Group. A controlled stress rheometer was used to provide the quantitative evaluations of the clay slurry properties. The research results indicate that the viscoelastic properties of the slurry are highly influenced by the shear history of the slurry, solids content, calcium concentration, and sample aging. Shear thinning behaviour was observed in all slurry samples, but the slurry viscosity increased with test time for a given shear rate. In order to classify the slurries, a method was developed to distinguish the gel strength. The slurries were then classified into 3 distinct patterns, including no gel, weak gel and strong gel. The evolution of the experimental protocols were described along with the current stability maps that correlate the domains of the gel strength according to the solids concentration, calcium ion content, and shear rate. It was concluded that the rheological properties of oil sands slurries influence bitumen recovery in commercial surface-mined oil sands operations. tabs., figs.

Baseline for beached marine debris on Sand Island, Midway Atoll

Science.gov (United States)

Ribic, Christine; Seba B. Sheavly,; John Klavitter,

2012-01-01

Baseline measurements were made of the amount and weight of beached marine debris on Sand Island, Midway Atoll, June 2008–July 2010. On 23 surveys, 32,696 total debris objects (identifiable items and pieces) were collected; total weight was 740.4 kg. Seventy-two percent of the total was pieces; 91% of the pieces were made of plastic materials. Pieces were composed primarily of polyethylene and polypropylene. Identifiable items were 28% of the total; 88% of the identifiable items were in the fishing/aquaculture/shipping-related and beverage/household products-related categories. Identifiable items were lowest during April–August, while pieces were at their lowest during June–August. Sites facing the North Pacific Gyre received the most debris and proportionately more pieces. More debris tended to be found on Sand Island when the Subtropical Convergence Zone was closer to the Atoll. This information can be used for potential mitigation and to understand the impacts of large-scale events such as the 2011 Japanese tsunami.

Production of oil from Intermountain West tar sands deposits

Energy Technology Data Exchange (ETDEWEB)

Glassett, J.M.; Glassett, J.A.

1976-03-01

Six tar sand deposits in the Intermountain West, each containing more than one billion barrels of oil in place, are identified. All of these deposits are in eastern Utah and contain a total of twenty-eight billion barrels of oil. The names of the six deposits arranged in descending order of desirability for large-scale surface-mining oil recovery operations are as follows: Sunnyside, Tar Sand Triangle, Asphalt Ridge, P.R. Spring, Circle Cliffs, and Hill Creek. An overview of each deposit is presented including geology, surface-mining variables, chemical processing variables, environmental aspects, and economics. A comparison of Utah tar sands and Athabasca, Alberta, Canada tar sands is also presented.

Maps showing characteristics of the Cabo Rojo West offshore sand deposit, southwestern Puerto Rico

Science.gov (United States)

Trumbull, James V.A.; Trias, Juan L.

1982-01-01

This report presents detailed information on a deposit of well-sorted coarse calcareous sand in water depths of 10-20 m in an area between 1 and 6 km west and southwest fo the promontory of Cabo Rojo, the southwesternmost corner of Puerto Rico. 

Presence of Campylobacter and Salmonella in sand from bathing beaches.

Science.gov (United States)

Bolton, F J; Surman, S B; Martin, K; Wareing, D R; Humphrey, T J

1999-02-01

The purpose of this study was to determine the presence of thermophilic Campylobacter spp. and Salmonella spp. in sand from non-EEC standard and EEC standard designated beaches in different locations in the UK and to assess if potentially pathogenic strains were present. Campylobacter spp. were detected in 82/182 (45%) of sand samples and Salmonella spp. in 10/182 (6%). Campylobacter spp. were isolated from 46/92 (50%) of samples from non-EEC standard beaches and 36/90 (40%) from EEC standard beaches. The prevalence of Campylobacter spp. was greater in wet sand from both types of beaches but, surprisingly, more than 30% of samples from dry sand also contained these organisms. The major pathogenic species C. jejuni and C. coli were more prevalent in sand from non-EEC standard beaches. In contrast, C. lari and urease positive thermophilic campylobacters, which are associated with seagulls and other migratory birds, were more prevalent in sand from EEC standard beaches. Campylobacter isolates were further characterized by biotyping and serotyping, which confirmed that strains known to be of types associated with human infections were frequently found in sand on bathing beaches.

Casting Ductile Iron in Layer Moulds Made from Ecological Sands

Directory of Open Access Journals (Sweden)

M. Rączka

2012-09-01

Full Text Available The article contains the results of tests performed under the target project in Hardtop Foundry Charsznica.The objective of the tests and studies was to develop a technology of making high-quality ductile iron castings, combined witheffective means of environmental protection. The studies presented in this article related to castings weighing from 1 to 300 kg made from ductile iron of grades 400-15 and 500-7, using two-layer moulds, where the facing and core sand was the sand with an alkaline organic binder, while backing sand was the sand with an inorganic geopolymer binder.A simplified method of sand reclamation was applied with possible reuse of the reclaim as an addition to the backing sand. The castiron spheroidising treatment and inoculation were selected taking into account the specific conditions of Hardtop Foundry. A pilot batch of castings was made, testing the gating and feeding systems and using exothermic sleeves on risers. The study confirmed the validity of the adopted concept of making ductile iron castings in layer moulds, while maintaining the content of sand with an organic binder at a level of maximum 15%.

Economic impacts of Alberta's oil sands, volume 1

International Nuclear Information System (INIS)

Timilsina, G.R.; LeBlanc, N.; Walden, T.

2005-01-01

In 2004, the international media recognized Alberta's oil sands as part of the global oil reserves, thereby establishing Canada as second to Saudi Arabia as potential oil producing nations. The economic impacts of Alberta's oil sands industry on economies were assessed at regional, provincial and international levels for the 2000 to 2020 period. A customized input-output model was used to assess economic impacts, which were measured in terms of changes in gross domestic product; employment and labour income; and, government revenues. Cumulative impacts on employment by sector and by jurisdiction were also presented. An investment of $100 billion is expected through 2020, resulting in production of crude bitumen and synthetic crude oil outputs valued at about $531 billion. The impact of the oil sands industry on local employment was also evaluated. It was shown that activities in the oil sands industry will lead to significant economic impact in Alberta, Ontario, Quebec and the rest of Canada. Alberta's local economy would be the main beneficiary of oil sands activities with nearly 3.6 million person years employment created in Alberta during the 2000 to 2020. Another 3 million person years employment would be created in other Canadian provinces and outside Canada during the same time period. A sensitivity analysis on the responsiveness to oil prices and the removal of various constraints incorporated in the main analysis was also presented. The federal government will be the largest recipient of revenues generated to to oil sands activities. The results of the study were compared with that of the National Task Force on Oil Sands Strategies. This first volume revealed the results of the study while the second volume includes the data and detailed results. 48 refs., 57 tabs., 28 figs

Applying the Analytic Hierarchy Process to Oil Sands Environmental Compliance Risk Management

Science.gov (United States)

Roux, Izak Johannes, III

Oil companies in Alberta, Canada, invested $32 billion on new oil sands projects in 2013. Despite the size of this investment, there is a demonstrable deficiency in the uniformity and understanding of environmental legislation requirements that manifest into increased project compliance risks. This descriptive study developed 2 prioritized lists of environmental regulatory compliance risks and mitigation strategies and used multi-criteria decision theory for its theoretical framework. Information from compiled lists of environmental compliance risks and mitigation strategies was used to generate a specialized pairwise survey, which was piloted by 5 subject matter experts (SMEs). The survey was validated by a sample of 16 SMEs, after which the Analytic Hierarchy Process (AHP) was used to rank a total of 33 compliance risks and 12 mitigation strategy criteria. A key finding was that the AHP is a suitable tool for ranking of compliance risks and mitigation strategies. Several working hypotheses were also tested regarding how SMEs prioritized 1 compliance risk or mitigation strategy compared to another. The AHP showed that regulatory compliance, company reputation, environmental compliance, and economics ranked the highest and that a multi criteria mitigation strategy for environmental compliance ranked the highest. The study results will inform Alberta oil sands industry leaders about the ranking and utility of specific compliance risks and mitigations strategies, enabling them to focus on actions that will generate legislative and public trust. Oil sands leaders implementing a risk management program using the risks and mitigation strategies identified in this study will contribute to environmental conservation, economic growth, and positive social change.

Phase behavior of methane hydrate in silica sand

International Nuclear Information System (INIS)

Sun, Shi-Cai; Liu, Chang-Ling; Ye, Yu-Guang; Liu, Yu-Feng

2014-01-01

Highlights: • Hydrate p-T trace in coarse-grained sediment is consistent with that in bulk water. • Fine-grained sediment affects hydrate equilibrium for the depressed water activity. • Hydrate equilibrium in sediment is related to the pore size distribution. • The application of hydrate equilibrium in sediment depends on the actual condition. -- Abstract: Two kinds of silica sand powder with different particle size were used to investigate the phase behavior of methane hydrate bearing sediment. In coarse-grained silica sand, the measured temperature and pressure range was (281.1 to 284.2) K and (5.9 to 7.8) MPa, respectively. In fine-grained silica sand, the measured temperature and pressure range was (281.5 to 289.5) K and (7.3 to 16.0) MPa, respectively. The results show that the effect of coarse-grained silica sand on methane hydrate phase equilibrium can be ignored; however, the effect of fine-grained silica sand on methane hydrate phase equilibrium is significant, which is attributed to the depression of water activity caused by the hydrophilicity and negatively charged characteristic of silica particle as well as the pore capillary pressure. Besides, the analysis of experimental results using the Gibbs–Thomson equation shows that methane hydrate phase equilibrium is related to the pore size distribution of silica sand. Consequently, for the correct application of phase equilibrium data of hydrate bearing sediment, the geological condition and engineering requirement should be taken into consideration in gas production, resource evaluation, etc

Dewatering Behaviour of Fine Oil Sands Tailings : An Experimental Study

NARCIS (Netherlands)

Yao, Y.

2016-01-01

Oil sands tailings are a warm aqueous suspension of sand, silt, clay, residual bitumen and naphtha. The tailings are hydraulically transported and stored in tailing ponds where they segregate, with the sand settling from suspension forming beaches and the remaining tailings flowing to the middle of

Seasonal changing sand waves and the effect of surface waves

NARCIS (Netherlands)

Sterlini, Fenneke; van Dijk, Thaiënne A.G.P.; IJzer, Steven; Hulscher, Suzanne; Schüttrumpf, Holger; Tomasicchio, Guiseppe Roberto

2012-01-01

Sand waves are wavelike subaqueous sediment structures that exist in large areas in shelf seas. Due to their characteristics sand waves can severely affect human offshore activities, such as navigation. This makes it important to understand the physical processes that shape and change sand waves. In

Acetylcholinesterase mutations and organophosphate resistance in sand flies and mosquitoes

Science.gov (United States)

Leishmaniasis is an insect-borne disease caused by several protozoan species in the genus Leishmania, which are vectored by sand fly species in the genera Phlebotomus or Lutzomyia, depending on the sand fly species geographic range. Sand fly bites and leishmaniasis significantly impacted U.S. milita...

Number of warning information sources and decision making during tornadoes.

Science.gov (United States)

Luo, Jianjun; Cong, Zhen; Liang, Daan

2015-03-01

Taking proper protective action upon receiving tornado warnings is critical to reducing casualties. With more warning information sources becoming available, how the number of such information sources affects decision making should be quantitatively investigated. To examine how the number of warning information sources affected individuals' decisions to take protective action during tornadoes. A telephone survey using random sampling was conducted in 2012 with residents in Tuscaloosa AL and Joplin MO, resulting in a working sample of 782 respondents. Both cities were struck by violent tornadoes (Enhanced Fujita Scale [EF]4 and EF5) in 2011. The analysis was conducted in 2013. Logistic regression analysis showed that relative to having only one warning information source, having two and three or more warning information sources significantly increased the odds of taking protective action in Joplin but not in Tuscaloosa; having three or more sources had a significantly stronger effect on taking protective action in Joplin than in Tuscaloosa. Having an emergency preparation plan in both cities and being white in Tuscaloosa significantly increased the odds of taking protective action, whereas being divorced in Joplin reduced these odds. Receiving warnings from more warning information sources might be more beneficial in places with less previous exposure to tornadoes and for populations with lower awareness of a potential tornado and higher probability of receiving no warnings. Emergency management agencies and public health officials should give priority to these places and populations when formulating disaster mitigation decisions and policies. Copyright © 2015 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

High Temperature Thermal Properties of Bentonite Foundry Sand

Directory of Open Access Journals (Sweden)

Krajewski P.K.

2015-06-01

Full Text Available The paper presents results of measuring thermal conductivity and heat capacity of bentonite foundry sand in temperature range ambient - 900­­°C. During the experiments a technical purity Cu plate was cast into the green-sand moulds. Basing on measurements of the mould temperature field during the solidification of the casting, the temperature relationships of the measured properties were evaluated. It was confirmed that water vaporization strongly influences thermal conductivity of the moulding sand in the first period of the mould heating by the poured casting.

Dark grains of sand: a geological storytelling

Science.gov (United States)

Gallo Maresca, Magda

2017-04-01

In the secondary Italian school the Earth science learning begins at first year, in synergy with other natural science subjects such as Astronomy, Chemistry and Biology. Italian teachers have to focus on the landscape geomorphological aspects and often Earth processes are difficult to display since they are related to certain phenomena happened during the past and often far from the involved country. In order to better understand the environment surrounding us, very simple and poor materials, like sands, allow the teachers to create attractive lab experiences. According to the IBSE (Inquiry Based Science Education) approach, a learning unit has been implemented starting from a walking along the light carbonate beaches of the Adriatic sea: a smart look to the sands ("engage step"), stroke the students fantasy pushing them to explore some strange black grains on the sands. Dirty sands? Or rock landscape, soil degradation and Ofanto river and coastal processes (erosion, transportation and deposition)? This was the teaching challenge. Due to the youngest age, a third level, guided inquiry, was adopted so the teacher is the "guide of inquiry" encouraging the students using the research question ("Why is the sand dark?", "Do all sands look the same?", "Where does it come from?") and driving the students around their investigation plans ("How can I measure grain size?"). A procedure to answer the above questions and validate the results and explanations has been implemented to allow the students to be proactive in their study. During the learning activities will be the students to ask for field trip to elaborate their new knowledge, verify and visualize the speculated processes. The teaching skills allow to address several geosciences domains such as mineralogy, petrology, regional geology and geodynamics as well as other scientific disciplines such as mathematics (more specifically statistics), forensic science and even life sciences (the presence of bioclasts might

Assessing environmental impacts of inland sand mining in parts of ...

African Journals Online (AJOL)

Sand is a valuable resource for construction and other purposes, however sand mining often result in serious environmental problems such as land degradation, loss of agricultural lands and biodiversity, as well increased poverty among people. This study assessed the environmental impacts of inland sand mining in six ...

Efficiency of Micro-fine Cement Grouting in Liquefiable Sand

International Nuclear Information System (INIS)

Mirjalili, Mojtaba; Mirdamadi, Alireza; Ahmadi, Alireza

2008-01-01

In the presence of strong ground motion, liquefaction hazards are likely to occur in saturated cohesion-less soils. The risk of liquefaction and subsequent deformation can be reduced by various ground improvement methods including the cement grouting technique. The grouting method was proposed for non-disruptive mitigation of liquefaction risk at developed sites susceptible to liquefaction. In this research, a large-scale experiment was developed for assessment of micro-fine cement grouting effect on strength behavior and liquefaction potential of loose sand. Loose sand samples treated with micro-fine grout in multidirectional experimental model, were tested under cyclic and monotonic triaxial loading to investigate the influence of micro-fine grout on the deformation properties and pore pressure response. The behavior of pure sand was compared with the behavior of sand grouted with a micro-fine cement grout. The test results were shown that cement grouting with low concentrations significantly decreased the liquefaction potential of loose sand and related ground deformation

Estimated sand and gravel resources of the South Merrimack, Hillsborough County, New Hampshire, 7.5-minute quadrangle

Science.gov (United States)

Sutphin, D.M.; Drew, L.J.; Fowler, B.K.

2006-01-01

A computer methodology is presented that allows natural aggregate producers, local governmental, and nongovernmental planners to define specific locations that may have sand and gravel deposits meeting user-specified minimum size, thickness, and geographic and geologic criteria, in areas where the surficial geology has been mapped. As an example, the surficial geologic map of the South Merrimack quadrangle was digitized and several digital geographic information system databases were downloaded from the internet and used to estimate the sand and gravel resources in the quadrangle. More than 41 percent of the South Merrimack quadrangle has been mapped as having sand and (or) gravel deposited by glacial meltwaters. These glaciofluvial areas are estimated to contain a total of 10 million m3 of material mapped as gravel, 60 million m3 of material mapped as mixed sand and gravel, and another 50 million m3 of material mapped as sand with minor silt. The mean thickness of these areas is about 1.95 meters. Twenty tracts were selected, each having individual areas of more than about 14 acres4 (5.67 hectares) of stratified glacial-meltwater sand and gravel deposits, at least 10-feet (3.0 m) of material above the watertable, and not sterilized by the proximity of buildings, roads, streams and other bodies of water, or railroads. The 20 tracts are estimated to contain between about 4 and 10 million short tons (st) of gravel and 20 and 30 million st of sand. The five most gravel-rich tracts contain about 71 to 82 percent of the gravel resources in all 20 tracts and about 54-56 percent of the sand. Using this methodology, and the above criteria, a group of four tracts, divided by narrow areas sterilized by a small stream and secondary roads, may have the highest potential in the quadrangle for sand and gravel resources. ?? Springer Science+Business Media, LLC 2006.

Study on the Permeability Characteristics of Polyurethane Soil Stabilizer Reinforced Sand

Directory of Open Access Journals (Sweden)

Jin Liu

2017-01-01

Full Text Available A polymer material of polyurethane soil stabilizer (PSS is used to reinforce the sand. To understand the permeability characteristics of PSS reinforced sand, a series of reinforcement layer form test, single-hole permeability test, and porous permeability test of sand reinforced with PSS have been performed. Reinforcement mechanism is discussed with scanning electron microscope images. The results indicated that the permeability resistance of sand reinforced with polyurethane soil stabilizer is improved through the formation of reinforcement layer on the sand surface. The thickness and complete degree of the reinforcement layer increase with the increasing of curing time and PSS concentration. The water flow rate decreases with the increasing of curing time or PSS concentration. The permeability coefficient decreases with the increasing of curing time and PSS concentration and increases with the increasing of depth in specimen. PSS fills up the voids of sand and adsorbs on the surface of sand particle to reduce or block the flowing channels of water to improve the permeability resistance of sand. The results can be applied as the reference for chemical reinforcement sandy soil engineering, especially for surface protection of embankment, slope, and landfill.

Inhalation exposure during spray application and subsequent sanding of a wood sealant containing zinc oxide nanoparticles.

Science.gov (United States)

Cooper, Michael R; West, Gavin H; Burrelli, Leonard G; Dresser, Daniel; Griffin, Kelsey N; Segrave, Alan M; Perrenoud, Jon; Lippy, Bruce E

2017-07-01

Nano-enabled construction products have entered into commerce. There are concerns about the safety of manufactured nanomaterials, and exposure assessments are needed for a more complete understanding of risk. This study assessed potential inhalation exposure to ZnO nanoparticles during spray application and power sanding of a commercially available wood sealant and evaluated the effectiveness of local exhaust ventilation in reducing exposure. A tradesperson performed the spraying and sanding inside an environmentally-controlled chamber. Dust control methods during sanding were compared. Filter-based sampling, electron microscopy, and real-time particle counters provided measures of exposure. Airborne nanoparticles above background levels were detected by particle counters for all exposure scenarios. Nanoparticle number concentrations and particle size distributions were similar for sanding of treated versus untreated wood. Very few unbound nanoparticles were detected in aerosol samples via electron microscopy, rather nano-sized ZnO was contained within, or on the surface of larger airborne particles. Whether the presence of nanoscale ZnO in these aerosols affects toxicity merits further investigation. Mass-based exposure measurements were below the NIOSH Recommended Exposure Limit for Zn, although there are no established exposure limits for nanoscale ZnO. Local exhaust ventilation was effective, reducing airborne nanoparticle number concentrations by up to 92% and reducing personal exposure to total dust by at least 80% in terms of mass. Given the discrepancies between the particle count data and electron microscopy observations, the chemical identity of the airborne nanoparticles detected by the particle counters remains uncertain. Prior studies attributed the main source of nanoparticle emissions during sanding to copper nanoparticles generated from electric sander motors. Potentially contrary results are presented suggesting the sander motor may not have been

Design and Fabrication of a Foundry Sand Mixer Using Locally ...

African Journals Online (AJOL)

Most small foundry shops mix their sand manually which is not efficient since homogenous mix cannot be guaranteed and even when foundry mixer are available most of them are imported costing the nation huge foriegn exchange. A foundry sand mixer capable of mixing foundry sand has been designed and fabricated ...

Mites and spiders act as biological control agent to sand flies

Directory of Open Access Journals (Sweden)

Diwakar Singh Dinesh

2014-02-01

Full Text Available Objective: To find out natural biological control agents of sand flies vector of kala azar in Bihar, India. Methods: Sand flies collected from the field using CDC light trap installing overnight to the collection site scrutitinized for Phlebotomus argentipes, the established vector of visceral leishmaniasis. Blood fed adult females were confined in the insectary for its development of life cycle. During developmental stages 2nd to 4th instars larvae were examined closely by using compound microscope for mite infestation. Adult spider residing along with sand flies collected in trap were kept in cage along with sand flies and their activities were watched closely and recorded by video and picture. Results: Mites were found predating 2nd to 4th instars larvae only under the laboratory conditions and lowering down the population of sand flies up to basal level within 15 d after infestation. One specific spider was found eating blood fed female sand flies kept inside the cage (n=50 attacking on lower part of thoracic region to kill the sand fly and ate desired soft part. Conclusions: Both predators, mites and spiders are acting as biological control agents to larvae and adults of sand flies respectively resulting variable density of vectors due to variable association with these predators and also cause lowering the transmission of the disease as hidden natural controlling agent of sand flies. The extensive study will be of immense help in controlling sand flies without use of environmental pollutant i.e. chemical insecticide.

Effects of bedding with recycled sand on lying behaviors, udder hygiene, and preference of lactating Holstein dairy cows.

Science.gov (United States)

Kull, J A; Ingle, H D; Black, R A; Eberhart, N L; Krawczel, P D

2017-09-01

Effects of bedding with recycled sand and season on lying behaviors, hygiene, and preferences of late-lactation Holstein cows were studied. It was hypothesized that recycled sand will decrease lying time and increase hygiene scores due to increased moisture content and organic matter, and thus a preference for the control sand will be evident. Cows (n = 64) were divided into 4 groups (n = 8 per group) per season. In summer (August to September), cows were balanced by days in milk (268.1 ± 11.9 d) and parity (2.0 ± 0.2). In winter (January to February), mean DIM was 265.5 ± 34.1 d. Cows were assigned to 1 of 2 treatments using a crossover design with each treatment lasting 7 d (no-choice phase): bedding with recycled sand (RS; n = 32) or control (CO; clean sand; n = 32). Stocking density was maintained at 100%. The choice phase allowed cows to have access to either treatment with stocking density at 50%. Accelerometers recorded daily lying time, number of lying bouts per day, lying bout duration (min/bout), and total steps per day. Teat swabs, milk, sand samples, and udder hygiene scores were collected on d 0, 3, and 7 of each experimental week. Samples were cultured for streptococci, staphylococci, and gram-negative bacteria. Video data were used to assess bedding preferences. All data were analyzed using the MIXED and GLIMMIX procedures of SAS 9.4 (SAS Institute Inc., Cary, NC). Lying time was not affected by treatment, but cows did take more steps during winter. Bacterial counts were elevated for cows on recycled sand. A preference was observed for clean sand during the summer, but no preference was observed for sand during the winter. Regardless of bedding, the most commonly observed behavior was lying in the stalls, which suggested either bedding might be suitable. Caution should be used with this interpretation of preference, as sand was recycled only once. This limited reclamation was still sufficient to potentially alter the composition of sand, driving

Alberta Oil Sands Equity annual report, 1992-93. Partnership and progress in Alberta's oil sands development

International Nuclear Information System (INIS)

1993-01-01

Alberta Oil Sands Equity (AOSE) manages the Alberta government's equity investments in oil sands and heavy oil projects. AOSE is a 16.74% participant in the Syncrude Project, a 10% participant in the OSLO (Other Six Leases Operation) Commercial Project and the OSLO New Ventures project, and a 24.17% participant in the Lloydminster Bi-Provincial Upgrader. Syncrude produces ca 12% of Canadian crude oil requirements, and AOSE's share yielded $44 million profit for 1992/93, slightly higher than the the $43.3 million the previous year. The OSLO Commercial Project is a proposed commercial oil sands plant with a mine site and extraction plant to be located north of Fort McMurray, and an upgrading facility to be situated north of Edmonton. Work on this project was suspended in early 1992. The OSLO New Ventures project will handle the exploration and development of the remaining five oil sands leases plus the southern portion of Lease 31. As of March 31, 1993, the project owners were considering a commercial demonstration project utilizing dredging and cold-water extraction processes. Two of the owners are unable to provide funding and discussions are under way to resolve the matter and move the program forward. The Lloydminster Bi-Provincial Upgrader opened Noveber 20, 1992, and production has reached 41,000 bbl/d, or 89% of design capacity. The upgrader will increase the value of heavy crude oil and thereby increase its demand. 5 figs., 3 tabs

An investigation of waste foundry sand in asphalt concrete mixtures.

Science.gov (United States)

Bakis, Recep; Koyuncu, Hakan; Demirbas, Ayhan

2006-06-01

A laboratory study regarding the reuse of waste foundry sand in asphalt concrete production by replacing a certain portion of aggregate with WFS was undertaken. The results showed that replacement of 10% aggregates with waste foundry sand was found to be the most suitable for asphalt concrete mixtures. Furthermore, the chemical and physical properties of waste foundry sand were analysed in the laboratory to determine the potential effect on the environment. The results indicated that the investigated waste foundry sand did not significantly affect the environment around the deposition

Bathymetric mapping of submarine sand waves using multiangle sun glitter imagery: a case of the Taiwan Banks with ASTER stereo imagery

Science.gov (United States)

Zhang, Hua-guo; Yang, Kang; Lou, Xiu-lin; Li, Dong-ling; Shi, Ai-qin; Fu, Bin

2015-01-01

Submarine sand waves are visible in optical sun glitter remote sensing images and multiangle observations can provide valuable information. We present a method for bathymetric mapping of submarine sand waves using multiangle sun glitter information from Advanced Spaceborne Thermal Emission and Reflection Radiometer stereo imagery. Based on a multiangle image geometry model and a sun glitter radiance transfer model, sea surface roughness is derived using multiangle sun glitter images. These results are then used for water depth inversions based on the Alpers-Hennings model, supported by a few true depth data points (sounding data). Case study results show that the inversion and true depths match well, with high-correlation coefficients and root-mean-square errors from 1.45 to 2.46 m, and relative errors from 5.48% to 8.12%. The proposed method has some advantages over previous methods in that it requires fewer true depth data points, it does not require environmental parameters or knowledge of sand-wave morphology, and it is relatively simple to operate. On this basis, we conclude that this method is effective in mapping submarine sand waves and we anticipate that it will also be applicable to other similar topography types.

Design of Screens for Sand Control of Wells

Directory of Open Access Journals (Sweden)

Ján Pinka

2006-04-01

Full Text Available Drilling, completion, production, and reservoir engineers, supervisors, foremen, superintendents, service company personnel, technologists and anyone involved with recommending, selecting, designing or on-site performance of well completions or workovers where sand production is, or may become, a serious problem will benefit from this course. Less sand influx can be expected in a horizontal well than in a vertical well. If horizontal holes in weak formation sands can be successfully gravel packed, the result could be significantly higher well productivity than with a liner, screen or pre-packed screen alone. The article covers innovative screens for sand control used in oil and gas industry from the world leaders in total completion. The type of screen (wire wrapped, reinforced, pre-packed, ect. should also be chosen with due consideration to running-in condition (curve radius, compression when the screens are pushed along the drain hole, etc..

Treatment of liquid radioactive waste by adsorption of some radionuclides on calcite sand, volcanic ash and comparing it with nickel ferro-cyanide

International Nuclear Information System (INIS)

Takriti, S.; Ali, A. F.

2009-09-01

Adsorption of 137 Cs existed in the liquid radioactive waste on the calcite sand and volcanic ash has been investigated. X-ray studies of sand and ash were used to have more information about the geological composition. The geological results show that the sand used is calcium carbonate and the ash is uncrystalline old volcanic ash. The radioactive measurements indicated that the calcite sand able to adsorb the 137 Cs with weak bond that can not resist the water flow. Otherwise, the volcanic ash can maintain the 137 Cs for long time and the water flow can not liberate the 137 Cs adsorbed into the volcanic ash. The adsorption of 137 Cs on nickel ferro-cyanide was more effective than other compounds. (author)

The stable stiffness triangle - drained sand during deformation cycles

DEFF Research Database (Denmark)

Sabaliauskas, Tomas; Ibsen, Lars Bo

2017-01-01

Cyclic, drained sand stiffness was observed using the Danish triaxial appa- ratus. New, deformation dependant soil property (the stable stiffness triangle) was detected. Using the the stable stiffness triangle, secant stiffness of drained sand was plausible to predict (and control) even during ir...... findings can find application in off-shore, seismic and other engi- neering practice, or inspire new branches of research and modelling wherever dynamic, cyclic or transient loaded sand is encountered....

White Sands, New Mexico as seen from STS-60

Science.gov (United States)

1994-01-01

White Sands National Monument (Park) is easily recognized in the center of this near-vertical color photograph. White Sands is the world's largest gypsum dune field. It represents an alabaster sea that covers nearly 300 square miles. At the southwest corner of the White Sands is dry lake, Lucero. In terms of cultural features the city of Alamogordo and Holloman Air Force Base can be seen with great clarity on this photograph.

Design of dry sand soil stratified sampler

Science.gov (United States)

Li, Erkang; Chen, Wei; Feng, Xiao; Liao, Hongbo; Liang, Xiaodong

2018-04-01

This paper presents a design of a stratified sampler for dry sand soil, which can be used for stratified sampling of loose sand under certain conditions. Our group designed the mechanical structure of a portable, single - person, dry sandy soil stratified sampler. We have set up a mathematical model for the sampler. It lays the foundation for further development of design research.

Re-usage of waste foundry sand in high-strength concrete.

Science.gov (United States)

Guney, Yucel; Sari, Yasin Dursun; Yalcin, Muhsin; Tuncan, Ahmet; Donmez, Senayi

2010-01-01

In this study, the potential re-use of waste foundry sand in high-strength concrete production was investigated. The natural fine sand is replaced with waste foundry sand (0%, 5%, 10%, and 15%). The findings from a series of test program has shown reduction in compressive and tensile strengths, and the elasticity modulus which is directly related to waste foundry inclusion in concrete. Nevertheless the concrete with 10% waste foundry sand exhibits almost similar results to that of the control one. The slump and the workability of the fresh concrete decreases with the increase of the waste foundry sand ratio. Although the freezing and thawing significantly reduces the mechanical and physical properties of the concrete. The obtained results satisfies the acceptable limits set by the American Concrete Institute (ACI). 2010 Elsevier Ltd. All rights reserved.

Study on strength characteristics of concrete using M-Sand and coconut fibers

Science.gov (United States)

Neeraja, D.; Wani, Amir Iqbal; Kamili, Zainulabideen; Agarwal, Krishnakant

2017-11-01

In the current world, concrete has become a very important part of the construction industry and the materials which are used in making concrete have evolved due to better quality of cement and better grade of coarse aggregates. The sand is an important part of concrete. It is mainly procured from natural sources. Thus the grade of sand is not under our control. The methods of removing sand from river beds are causing various environmental issues and river sand is depleting at a faster rate than it is replaced by natural methods. Hence, various replacements for the river sand are being done, one of which is manufactured-sand. It is obtained from various granite quarries. Manufactured-sand or M-sand is slowly replacing the fine aggregate in the concrete as the sand is well graded and gives higher strength of concrete. There are various fibers used for reinforcing concrete which consist mainly of artificial or steel fibers. Some of these fibers are quite costly and sometimes difficult to obtain. So there are many natural fibers which can be used in place of these fibers, one of which is coconut fiber, extracted from the shell of a coconut. Coconut fibers are used in various industries like rope making, coir mattresses etc. Since these fibers are one of the strongest fibers among naturally occuring fibers, they can be used in the concrete mix to increase the resistance in concrete. They are also light weight and easily available and thus can be used in reinforcement of concrete. The studies up till now have tested the use of coconut fibers in normal concrete involving river sand but in this study a particular ratio of M-sand and river sand is used to get the maximum possible strength. Hence, in this project an attempt was made to use M-sand and coconut fiber in concrete. Based on the test results, it can be concluded that combination of M-sand and coconut fibers gave favorable results in strength criteria.

Sand transport in urbanized beaches - models and reality

International Nuclear Information System (INIS)

Pineiro, G.; Norbis, W.; Panario, D.

2012-01-01

The general objective is to quantify the wind transport of sand in the urbanized beaches. The specific objectives include testing and calibration of the wind velocity as well as the classification of the beaches according to the magnitude and the direction of sand transport

Geophysics comes of age in oil sands development

Energy Technology Data Exchange (ETDEWEB)

Bauman, P. [WorleyParsons Komex, Calgary, AB (Canada); Birch, R.; Parker, D.; Andrews, B. [Calgary Univ., AB (Canada). Dept. of Geology and Geophysics

2008-07-01

This paper discussed geophysical techniques developed for oil sands exploration and production applications in Alberta's oil sands region. Geophysical methods are playing an important role in mine planning, tailings containment, water supply, and land reclamation activities. Geophysics techniques are used to estimate the volume of muskeg that needs to be stripped and stored for future reclamation activities as well as to site muskeg piles and delineate the thickness of clay Clearwater formations overlying Cretaceous oil-bearing sands. 2-D electrical resistivity mapping is used to map river-connected deep bedrock Pleistocene paleovalleys in the region. Geophysical studies are also used to investigate the interiors of dikes and berms as well as to monitor salt migration within tailings piles. Sonic and density logs are used to create synthetic seismograms for mapping the Devonian surface in the region. The new applications included the calculation of bitumen saturation from surface sands and shales; muskeg thickness mapping; and non-intrusive monitoring of leachate plumes. Geophysical techniques included 2-D electrical resistivity imaging; transient electromagnetic (EM) technologies; ground penetrating radar; and high-resolution seismic reflections. Polarization, surface nuclear magnetic resonance and push-probe sensing techniques were also discussed. Techniques were discussed in relation to Alberta's Athabasca oil sands deposits. 4 refs.

Seismic stochastic inversion identify river channel sand body

Science.gov (United States)

He, Z.

2015-12-01

The technology of seismic inversion is regarded as one of the most important part of geophysics. By using the technology of seismic inversion and the theory of stochastic simulation, the concept of seismic stochastic inversion is proposed.Seismic stochastic inversion can play an significant role in the identifying river channel sand body. Accurate sand body description is a crucial parameter to measure oilfield development and oilfield stimulation during the middle and later periods. Besides, rational well spacing density is an essential condition for efficient production. Based on the geological knowledge of a certain oilfield, in line with the use of seismic stochastic inversion, the river channel sand body in the work area is identified. In this paper, firstly, the single river channel body from the composite river channel body is subdivided. Secondly, the distribution of river channel body is ascertained in order to ascertain the direction of rivers. Morever, the superimposed relationship among the sand body is analyzed, especially among the inter-well sand body. The last but not at the least, via the analysis of inversion results of first vacuating the wells and continuous infilling later, it is meeted the most needs well spacing density that can obtain the optimal inversion result. It would serve effective guidance for oilfield stimulation.

Particle size analyses in and around mineral sands operations

International Nuclear Information System (INIS)

Koperski, J.

1993-01-01

Activity Median Aerodynamic Diameters (AMADs) of airborne dust in and around West Australian heavy mineral sands operations have been investigated. Monitoring of dry separation plant workers, positional monitoring of the plant environment and positional monitoring outdoors were conducted. The number of AMAD detections was 49, 21 and 37, respectively. Mean AMAD values of 15.7μm (GSD 2.9) for personal monitoring, 4.6μm (GSD 3.5) for positional monitoring indoors and 2.7 μm (GSD 4.8) for hi-vol positional monitoring outdoors were obtained. The size distribution of airborne radioactivity was observed to be log-normal. Applying the ICRP 30 inhalation model (ICRP 1979) and both, ICRP 26 (ICRP 1977) and ICRP 60 (ICRP 1990) recommendations, intake-to-dose conversion factors for internal alpha exposure from the Th series radionuclides (in secular equilibrium, solubility Class Y) associated with airborne dust were subsequently assessed. It has been concluded that no single AMAD value would characterise heavy mineral sands operations. In the areas of the greatest radiological impact (dry separation plants indoors) emphasis should be focused upon personal monitoring strategies. In the areas of a lower impact (outdoors), a positional cascade impactor data may be used for personal AMAD assessment. Application of the reference 1μm AMAD value may lead to an over 5-fold overestimation of internal doses for the dry separation plant workers and to about 2-fold dose overestimation for the other workers. Hence, the need and importance of conducting site-specific particle size analyses for individual mineral sands operations. 13 refs., 4 tabs., 6 figs

Effect of River Indus Sand on Concrete Tensile Strength

Directory of Open Access Journals (Sweden)

M. T. Lakhiar

2018-04-01

Full Text Available In the development of Pakistan construction industry, the utilization of River Indus sand in concrete as fine aggregate has expanded tremendously. The aim of this research is to study the effect of Indus River sand on the tensile strength of various grades of concrete when it is utilized as fine aggregate. Concrete Samples of M15, M20 and M25 grade concrete were cured for 7, 14, 21 and 28 days. Based on the results, it is found that concrete became less workable when Indus river sand was utilized. It is recorded that tensile strength of concrete is decreased from 5% up to 20% in comparison with hill sand. The results were derived from various concrete grades.

Baseline susceptibility to pyrethroid and organophosphate insecticides in two old world sand fly species (diptera: psychodidae)

Science.gov (United States)

A study was conducted with support from the Department of Defense’s Deployed Warfighter Protection (DWFP) Program to evaluate the susceptibility of two old world sand fly species, Phlebotomus papatasi and P. duboscqi, to a number of commonly used pyrethroid and organophosphate insecticides. A simpl...

Response of stiff piles in sand to long-term cyclic lateral loading

DEFF Research Database (Denmark)

Bakmar, Christian LeBlanc; Houlsby, Guy T.; Byrne, Byron W.

2010-01-01

. To address this, a series of laboratory tests were conducted where a stiff pile in drained sand was subjected to between 8000 and 60000 cycles of combined moment and horizontal loading. A typical design for an offshore wind turbine monopile was used as a basis for the study, to ensure that pile dimensions...... and loading ranges were realistic. A complete non-dimensional framework for stiff piles in sand is presented and applied to interpret the test results. The accumulated rotation was found to be dependent on relative density and was strongly affected by the characteristics of the applied cyclic load. The pile...... stiffness increased with number of cycles, which contrasts with the current methodology where static p - y curves are degraded to account for cyclic loading. Methods are presented to predict the change in stiffness and the accumulated rotation of a stiff pile due to long-term cyclic loading. The use...

LAND COVER DYNAMICS OF OLESHKY SANDS: TIME-SERIES ANALYSIS 1987-2017

Directory of Open Access Journals (Sweden)

V. Bogdanets

2017-11-01

Full Text Available Oleshky Sands is the largest expanse of sand in Ukraine and the second in Europe. In the beginning of XX century sands moving outside of arenas was almost stopped by planting trees (Pinus nigra ssp. pallasian and Pinus sylvestris L., and the territory had different use during the years. A 30-year (1987-2017 time series of Landsat imagery obtained via USGS geoservice was used to reveal land cover dynamics of deserted landscapes of Oleshky sands using QGIS software. Heavy sand storms can impact nearby settlements and expose harmful effect on local industry and quality of life of local communities. Forest fire is another dangerous factor for protective forest plantations during last years. Our estimation shows that sandy areas increase during 2000-2017; generally, conservation measures had constant effect despite afforestation of last years. The preventive effect of forest on sands moving at Oleshky sands can be characterized as stable in case of constant care about the forest plantation and proper documentation on land use and ownership.

A new GIS-based model for automated extraction of Sand Dune encroachment case study: Dakhla Oases, western desert of Egypt

Directory of Open Access Journals (Sweden)

M. Ghadiry

2012-06-01

Full Text Available The movements of the sand dunes are considered as a threat for roads, irrigation networks, water resources, urban areas, agriculture and infrastructures. The main objectives of this study are to develop a new GIS-based model for automated extraction of sand dune encroachment using remote sensing data and to assess the rate of sand dune movement. To monitor and assess the movements of sand dunes in Dakhla oases area, multi-temporal satellite images and a GIS-developed model, using Python script in Arc GIS, were used. The satellite images (SPOT images, 1995 and 2007 were geo-rectified using Erdas Imagine. Image subtraction was performed using spatial analyst in Arc GIS, the result of image subtraction obtains the sand dune movement between the two dates. The raster and vector shape of sand dune migration was automatically extracted using spatial analyst tools. The frontiers of individual dunes were measured at different dates and movement rates were analyzed in GIS. The ModelBuilder in Arc GIS was used in order to create a user friendly tool. The custom built model window is easy to handle by any user who wishes to adapt the model in his work. It was found that the rate of sand dune movement ranged between 3 and 9 m per year. The majority of sand dunes have a rate movement between 0 and 6 m and very few dunes had a movement rate between 6 and 9 m. Integrating remote sensing and GIS provided the necessary information for determining the minimum, maximum, mean, rate and area of sand dune migration.

Beach Sand Analysis for Indicators of Microbial Contamination

Science.gov (United States)

Traditional beach monitoring has focused on water quality, with little attention paid to health risks associated with beach sand. Recent research has reported that fecal indicator bacteria, as well as human pathogens can be found in beach sand and may constitute a risk to human h...

Improving the geotechnical behavior of sand through cohesive admixtures

Directory of Open Access Journals (Sweden)

Mohie eldin Mohamed Afify Elmashad

2018-04-01

Full Text Available Irrigation projects in Egypt have been facing tremendous challenges, mostly is the scarcity of irrigation water. The current research presents the effect of different cohesive admixture on the conductivity of siliceous sand in general and its other geotechnical properties. Two different types of conventional swelling clay from (Toshka, 6th of October as well as bentonite were used to construct the irrigation canals and embankment. The results indicated that increase in the plasticity properties of the treated soil also decrease the permeability and infiltration. Moreover, the dry density of 2.08 t/m3 was obtained from sand and 20% 6th of October mixture, also the CBR of 31.20% were obtained from sand and 8% 6th of October mixture. Increasing the bentonite ratio increases the cohesion and decreasing the permeability. The swelling ratios of sand 6th of October Clay mixture is equal to 0.28%, and the fictitious stress at which the swelling ratio is nil, is equal to 16 kPa. Keywords: Sand, Swelling clay, Bentonite, Compaction test, Consolidation test, Triaxial test

Sustainable use of oil sands for geotechnical construction and road building

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2012-02-01

Full Text Available Oil sands are natural deposits of bituminous sand materials that are mined and processed for crude oil. They are routinely used in oil sand fields for building temporary and sometimes permanent roads serving mining and hauling activities. Although...

Experimental Investigation of Evaporation and Drainage in Wettable and Water-Repellent Sands

Directory of Open Access Journals (Sweden)

Dae Hyun Kim

2015-05-01

Full Text Available This study presents experimental results on evaporation and drainage in both wettable and water-repellent sands whose surface wettability was artificially modified by silanization. The 2D optical and 3D X-ray computed tomographic imaging was performed during evaporation and the water retention during cyclic drainage and infiltration was measured to assess effects of wettability and initial wetting conditions. The evaporation gradually induces its front at the early stage advance regardless of the wettability and sand types, while its rate becomes higher in water-repellent Ottawa sand than the wettable one. Jumunjin sand which has a smaller particle size and irregular particle shape than Ottawa sand exhibits a similar evaporation rate independent of wettability. Water-repellent sand can facilitate the evaporation when both wettable and water-repellent sands are naturally in contact with each other. The 3D X-ray imaging reveals that the hydraulically connected water films in wettable sands facilitate the propagation of the evaporation front into the soil such that the drying front deeply advances into the soil. For cyclic drainage-infiltration testing, the evolution of water retention is similar in both wettable and water-repellent sands when both are initially wet. However, when conditions are initially dry, water-repellent sands exhibit low residual saturation values. The experimental observations made from this study propose that the surface wettability may not be a sole factor while the degree of water-repellency, type of sands, and initial wetting condition are predominant when assessing evaporation and drainage behaviors.

The Karakum and Kyzylkum sand seas dynamics; mapping and palaeoclimatic interpretations

Science.gov (United States)

Maman, Shimrit; Blumberg, Dan G.; Tsoar, Haim; Porat, Naomi

2015-04-01

Sand seas are large basins in deserts that are mantled by wind-swept sand and that exhibit varying degrees of vegetation cover. Wilson (1973) was the first to globally map and classify sand seas. Beyond Wilson's maps, however, little research has been published regarding the Karakum and Kyzylkum sand seas of Central Asia. Wilson's maps delineate active ergs from inactive ergs based solely on precipitation. His assumption of annual average rainfall as a factor determining mobility vs. stability of sand seas is too simplistic and does not take into consideration other factors such as biogenic soil crusts and wind power, both of which are known to have major effects on the dynamics of sand dunes. Literature related to mapping and classifying the Central Asian ergs by remote sensing or sand sea classification state (stable/active) is lacking. Moreover, the palaeoclimatic significance of dunes in Central Asia is difficult to assess, as there has been few studies of dune stratigraphy and numerical ages are lacking. Optically stimulated luminescence (OSL) is a firm optical dating method that is used to determine the elapsed time since quartz grains were last exposed to sunlight, thus, their burial. Yet, absolute ages indicating mobilization and stabilization of these sands, are still inadequately known and are here under discussion. The broad concern of this research was to determine the dynamics of the Central Asian sand seas and study the palaeoclimatic changes that brought to their stabilization. As there are no reliable maps or aeolian discussion of these sands, establishment of a digital data base was initially conducted, focusing on identifying and mapping these sand seas. The vast area and inaccessibility make traditional mapping methods virtually impossible. A variety of space-borne imagery both optical and radar, with varying spectral and spatial resolutions was used. These images provided the basis for mapping sand distribution, dune forms, and vegetation cover

Characteristics and Dynamics of a Large Sub-Tidal Sand Wave Field—Habitat for Pacific Sand Lance (Ammodytes personatus, Salish Sea, Washington, USA

Directory of Open Access Journals (Sweden)

H. Gary Greene

2017-10-01

Full Text Available Deep-water sand wave fields in the San Juan Archipelago of the Salish Sea and Pacific Northwest Washington, USA, have been found to harbor Pacific sand lance (PSL, Ammodytes personatus, a critical forage fish of the region. Little is known of the dynamics of these sand waves and the stability of the PSL sub-tidal habitats. Therefore, we have undertaken an initial investigation to determine the dynamic conditions of a well-known PSL habitat in the San Juan Channel within the Archipelago using bottom sediment sampling, an acoustical doppler current profiling (ADCP system, and multi-beam echo sounder (MBES bathymetry. Our study indicates that the San Juan Channel sand wave field maintained its shape and bedforms geometry throughout the years it has been studied. Based on bed phase diagrams for channelized bedforms, the sand waves appear to be in a dynamic equilibrium condition. Sea level rise may change the current regime within the Archipelago and may alter some of the deep-water or sub-tidal PSL habitats mapped there. Our findings have global significance in that these dynamic bedforms that harbor PSL and sand-eels elsewhere along the west coast of North America and in the North Sea may also be in a marginally dynamic equilibrium condition and may be prone to alteration by sea level rise, indicating an urgency in locating and investigating these habitats in order to sustain the forage fish.

Modelling of constitutive behavior of sand in the low stress regime: an implementation of SANISAND

DEFF Research Database (Denmark)

Latini, Chiara; Zania, Varvara; Tamagnini, Claudio

2017-01-01

The paper provides background information for the modification of SANISAND (2004) constitutive model in order to capture the mechanical behavior of sand in the low stress regime. In the implementation of this model in finite element programs, computational difficulties arise due to the gradient...

On Foundation Improvement By Sand Replacement | Abam | Global ...

African Journals Online (AJOL)

This paper describes a simple foundation improvement method involving the replacement of poor foundation bearing soils with sand and the resultant improvement in bearing capacity and the minimization of settlement at the site of a large storage tank. Minimum thickness of sand replacement for various foundation loads ...

Ask Dr. Sue: Tree Climbing and Care of Sand Play Areas.

Science.gov (United States)

Aronson, Susan S.

1993-01-01

Discusses safety aspects of tree climbing and the use of sand in outdoor play areas at day care centers. Specifies ways to prune trees so that they are unclimbable and methods for maintaining sand areas. Includes a recipe for sand disinfectant. (MDM)

Differences and commonalities impregnation of dry and wet sand

Directory of Open Access Journals (Sweden)

Maujuda МUZAFFAROVA

2014-09-01

Full Text Available The article is devoted to research new methods of physic-chemical methods of preventing deflation to protect railways and highways from such phenomena as exogenous sand drifts. In particular, first studied the possibility of using binders in sand wet state. Results can significantly extend the scope of the method, and identified with particular impregnation maintaining stability requirements protective cover reduces both the concentration previously recommended binders, and their costs, thereby securing implementation in practice of shifting sands resource-saving technology.

Research for the development of the crushed sand (II)

Energy Technology Data Exchange (ETDEWEB)

Park, Chul Whan; Kang, Sun Duck; Min, Jeong Sik; Synn, Joong Ho; Park, Chan [Korea Institute of Geology Mining and Materials, Taejon (Korea)

1998-12-01

The sand obtained from river is not sufficient in amount for the demand of construction industry. The production of sand from sea and mountain is rapidly increasing for the substitution of the river sand. The industry of the crushed sand has recently been bricked for the above. Crushing, classification and dewatering are the main processes in the crushed sand production. This report concentrates the improvement of classification technology and the quality of ready mixed concrete. Air separator with testing size for the classification in the process of dry system was developed by the Yeung Nam university. This plant has the excellent efficiency for the collection of fine powder, but needs the improvement for separating function. The collection efficiency of the testing size air separator is reached to 99% in the condition of high revolution and low feeding speed. The classification efficiency is checked about 50% maximum in the condition of 200 rpm and dry sample. Energy saving test was carried out in the production process of the dry system with the rock samples of 14-17% of water content. The classification efficiency for dewatering sample passed the heating process was analysed 91.5%. But that for high water content sample skipped the heating process was analysed more or less 77%. Even though the heating process causes the classification efficiency being high, the energy consumption can also cause the price of the crushed sand high. Water content of sample as the effective element for the optimization of classification efficiency and energy saving should be studied next year. The quality of crushed sand in the mixing design. The test was carried out with the various content in mixing, the strength of ready mixed concrete has the maximum for the mould with 50-60% content of crushed sand. This strength is higher by 5-30% than 30% content and by 20-32% than 0% content, which means that the industry has the possibility of progress. (author). 10 refs., 31 tabs., 49

Alberta Oil Sands Equity annual report, 1991-92. Partnership and progress in Alberta's oil sands development

International Nuclear Information System (INIS)

1992-01-01

Alberta Oil Sands Equity (AOSE) manages the Alberta government's equity investments in oil sands and heavy oil projects. AOSE is a 16.74% participant in the Syncrude Project, a 10% participant in the OSLO (Other Six Leases Operation) Commercial Project and the OSLO New Ventures project, and a 24.17% participant in the Lloydminster Bi-Provincial Upgrader. Syncrude produces over 11% of Canadian crude oil requirements, and AOSE's share yielded $43.3 million profit for 1991/92, down significantly from the $82.1 million the previous year due to lower oil prices. The OSLO Commercial Project is a proposed commercial oil sands plant with a mine site and extraction plant to be located north of Fort McMurray, and an upgrading facility to be situated north of Edmonton. Work on this project was suspended in early 1992. The OSLO New Ventures project will handle the exploration and development of the remaining five oil sands leases plus the southern portion of Lease 31. As of March 31, 1992, the project owners were considering a commercial demonstration project utilizing dredging and cold-water extraction processes. Two of the owners are unable to provide funding and discussions are under way to resolve the matter and move the program forward. The Lloydminster Bi-Provincial Upgrader was nearly 90% complete in March 1992 and full startup is expected in November 1992; engineering work was completed in March 1991. The upgrader will increase the value of heavy crude oil and thereby increase its demand. 4 figs., 4 tabs

Environmental impact assessment of sand mining from the small catchment rivers in the southwestern coast of India: a case study.

Science.gov (United States)

Sreebha, Sreedharan; Padmalal, Damodaran

2011-01-01

In the past few decades, the demand for construction grade sand is increasing in many parts of the world due to rapid economic development and subsequent growth of building activities. This, in many of the occasions, has resulted in indiscriminate mining of sand from in-stream and floodplain areas leading to severe damages to the river basin environment. The case is rather alarming in the small catchment rivers like those draining the southwestern coast of India due to limited sand resources in their alluvial reaches. Moreover, lack of adequate information on the environmental impact of river sand mining is a major lacuna challenging regulatory efforts in many developing countries. Therefore, a scientific assessment is a pre-requisite in formulating management strategies in the sand mining-hit areas. In this context, a study has been made as a case to address the environmental impact of sand mining from the in-stream and floodplain areas of three important rivers in the southwestern coast of India namely the Chalakudy, Periyar and Muvattupuzha rivers, whose lowlands host one of the fast developing urban-cum-industrial centre, the Kochi city. The study reveals that an amount of 11.527 million ty(-1) of sand (8.764 million ty(-1) of in-stream sand and 2.763 million ty(-1) of floodplain sand) is being mined from the midland and lowland reaches of these rivers for construction of buildings and other infrastructural facilities in Kochi city and its satellite townships. Environmental Impact Assessment (EIA) carried out as a part of this investigation shows that the activities associated with mining and processing of sands have not only affected the health of the river ecosystems but also degraded its overbank areas to a large extent. Considering the degree of degradation caused by sand mining from these rivers, no mining scenario may be opted in the deeper zones of the river channels. Also, a set of suggestions are made for the overall improvement of the rivers and its

Environmental Impact Assessment of Sand Mining from the Small Catchment Rivers in the Southwestern Coast of India: A Case Study

Science.gov (United States)

Sreebha, Sreedharan; Padmalal, Damodaran

2011-01-01

In the past few decades, the demand for construction grade sand is increasing in many parts of the world due to rapid economic development and subsequent growth of building activities. This, in many of the occasions, has resulted in indiscriminate mining of sand from instream and floodplain areas leading to severe damages to the river basin environment. The case is rather alarming in the small catchment rivers like those draining the southwestern coast of India due to limited sand resources in their alluvial reaches. Moreover, lack of adequate information on the environmental impact of river sand mining is a major lacuna challenging regulatory efforts in many developing countries. Therefore, a scientific assessment is a pre-requisite in formulating management strategies in the sand mining-hit areas. In this context, a study has been made as a case to address the environmental impact of sand mining from the instream and floodplain areas of three important rivers in the southwestern coast of India namely the Chalakudy, Periyar and Muvattupuzha rivers, whose lowlands host one of the fast developing urban-cum-industrial centre, the Kochi city. The study reveals that an amount of 11.527 million ty-1 of sand (8.764 million ty-1 of instream sand and 2.763 million ty-1 of floodplain sand) is being mined from the midland and lowland reaches of these rivers for construction of buildings and other infrastructural facilities in Kochi city and its satellite townships. Environmental Impact Assessment (EIA) carried out as a part of this investigation shows that the activities associated with mining and processing of sands have not only affected the health of the river ecosystems but also degraded its overbank areas to a large extent. Considering the degree of degradation caused by sand mining from these rivers, no mining scenario may be opted in the deeper zones of the river channels. Also, a set of suggestions are made for the overall improvement of the rivers and its

CFD evaluation of erosion rate around a bridge near a sand dune

Science.gov (United States)

He, Wei; Huang, Ning; Dun, Hongchao; Wang, Wenbo

2017-04-01

This study performs a series of simulations through solving the Navier-Stokes equations and the RNG k-ε turbulence model to investigate the wind erosion rates around a bridge in a desert area with sand dunes. The digital elevation model of sand dunes and the bridge model are obtained respectively from hypsographic map and construction drawings. Through combining them into the CFD software of Fluent the simulation zone was formed. The data of wind speed obtained from field observation is fitted into a logarithm format, which was imported into Fluent model as a inlet wind speed condition. Then, the effect of Dun-Go railway on wind-blown sand movement of the neighbouring environment is simulated. The results exhibit that affected by both the sand dune and bridge, the flow field is in a complex condition. It is also shown that the bridge in upstream of the sand dune will not increase the sand transport rate intensively, but change both wind velocity gradient and turbulence kinetic energy over surface of sand dune. On the other hand, when the bridge is built downstream the sand dune, simulation results show that sand deposition rate would be decreased in reference region downstream the pier.

The oil sands: A new energy vision for Canada

International Nuclear Information System (INIS)

1995-01-01

Canada's oil sands deposits were considered to offer huge potential for wealth generation and enduring social benefits. This report showed that putting in action the plan developed by the National Task Force on Oil Sands Strategies would help unlock this potential and realize the benefits; the forecast called for a doubling or tripling of oil sands production over the next 25 years. The plan should also predicted an increase in investments in oil sands since the fiscal regime would be stable and the product would be in increasing demand. New capital investment should generate significant environmental, social and economic benefits. The real outcome would be increased national prosperity, since further growth in investment would translate into thousands of skilled jobs across Canada, expansion of government revenues, and improvements to Canada's trade balance. 1 ill

Oil sands: Strategies for future development - An overview

International Nuclear Information System (INIS)

Yildirim, E.

1995-01-01

The Alberta Chamber of Resources developed a Task Force in 1993 to promote oil sands development, and to identify and publicize the social and economic benefits of oil sands operations. Formation, mission of the National Task Force, impediments and opportunities for development were summarized. Attributes of oil sands, benefits of their development, impediments to development, strategic development and potential growth scenarios were discussed. Cooperation between government and industry was deemed essential. Recommendations included development of a bitumen pipeline network, provision of incentives to encourage development, encouragement of risk and reward sharing between bitumen producers and up graders, and diversification of products and by-products. 7 figs., 12 refs

Used Furan Sand Reclamation in REGMAS Vibratory Unit

Directory of Open Access Journals (Sweden)

Dańko J.

2015-09-01

Full Text Available The paper, especially dealt with problems of reclamation of used furan sand, carried out in new, vibratory sand reclamation unit REGMAS developed by researches from AGH-University of Science and Technology, Faculty of Foundry Engineering in Cracow (Poland. Functional characteristics of reclamation unit as well as the results of reclamation of used sand with furfuryl resin are discussed in the paper. The quality of reclaim was tested by means of the LOI and pH value, dust content in the reclaim and at least by the the quality of the castings produced in moulds prepared with the use of reclaimed matrix.

Opportunities for CANDU for the Alberta oil sands

International Nuclear Information System (INIS)

Hopwood, J.M.; Bock, D.; Miller, A.; Kuran, S.; Keil, H.; Fiorino, L.; Hau, K.; Zhou, X.; Dunbar, R.B.

2003-01-01

The Alberta oil sands bitumen deposits comprise of one of the largest sources hydrocarbon in the world, and have emerged as the fastest growing, soon to be dominant, source of crude oil in Canada. The oil industry has made great strides in improving the effectiveness of gathering this resource. In particular, alternatives to open-pit mining have been developed which enable in-site recovery of underground deposits with a minimum of environmental disruption. The main challenge that remains is the large quantity of energy needed in the process of extracting the oil and upgrading it to commercial levels. For a typical in-situ extraction project, about 18% of the energy content of the oil produced is used up in the extraction process, while a further 5% is used in generating hydrogen to upgrade the bitumen to synthetic crude oil. Looking ahead, even as improvements in energy use efficiency, (and hydrocarbon use efficiency) counterbalance the increases in hydrocarbon demand from economic growth (particularly in the developing world), Canada and Alberta recognize that the oil sands resource will be needed, and both support the development of this resource in an environmentally responsible way. The large energy requirement for the oil sands extraction process represents a challenge with regard to both environmental impact and security of supply. The use of natural gas, the current energy supply, has impacts in terms of air quality (via NOX and other emissions) and also represents a large greenhouse gas emissions component. As the oil sands industry expands, the availability of natural gas also becomes a concern, as does price and price stability. With this background, the opportunity for nuclear reactors to provide an economical, reliable, virtually zero-emission source of energy for the oil sands becomes very important. Over the last few years, developments in oil sands extraction technology, and developments in CANDU technology through the Advanced CANDU Reactor, (ACR

A sand budget for Marble Canyon, Arizona: implications for long-term monitoring of sand storage change

Science.gov (United States)

Grams, Paul E.

2013-01-01

Recent U.S. Geological Survey research is providing important insights into how best to monitor changes in the amount of tributary-derived sand stored on the bed of the Colorado River and in eddies in Marble Canyon, Arizona. Before the construction of Glen Canyon Dam and other dams upstream, sandbars in Glen, Marble, and Grand Canyons were replenished each year by sediment-rich floods. Sand input into the Colorado River is crucial to protecting endangered native fish, animals, and plants and cultural and recreational resources along the river in Glen Canyon National Recreation Area and Grand Canyon National Park.

Permeability Tests on Eastern Scheldt Sand

DEFF Research Database (Denmark)

Jakobsen, Kim Parsberg

on the characteristics of the soil matrix, the permeability is determined for different void ratios. All tests are performed on reconstituted specimens of Eastern Scheldt Sand. The permeability is determined by use of a falling head apparatus. Finally the test results are briefly summarised and a relationship between......The flow through porous media plays an important role in various engineering disciplines, as for example in ground water hydrology and soil mechanics. In the present study the permeability is determined for a fine, saturated sand. As the flow through a porous media strongly depends...

Contribution of sand-associated enterococci to dry weather water quality.

Science.gov (United States)

Halliday, Elizabeth; Ralston, David K; Gast, Rebecca J

2015-01-06

Culturable enterococci and a suite of environmental variables were collected during a predominantly dry summer at a beach impacted by nonpoint source pollution. These data were used to evaluate sands as a source of enterococci to nearshore waters, and to assess the relationship between environmental factors and dry-weather enterococci abundance. Best-fit multiple linear regressions used environmental variables to explain more than half of the observed variation in enterococci in water and dry sands. Notably, during dry weather the abundance of enterococci in dry sands at the mean high-tide line was significantly positively related to sand moisture content (ranging from sands. Tidal forcing modulated the abundance of enterococci in the water, as both turbidity and enterococci were elevated during ebb and flood tides. The probability of samples violating the single-sample maximum was significantly greater when collected during periods with increased tidal range: spring ebb and flood tides. Tidal forcing also affected groundwater mixing zones, mobilizing enterococci from sand to water. These data show that routine monitoring programs using discrete enterococci measurements may be biased by tides and other environmental factors, providing a flawed basis for beach closure decisions.

K West Basin Sand Filter Backwash Sample Analysis

Energy Technology Data Exchange (ETDEWEB)

Fiskum, Sandra K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Smoot, Margaret R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Coffey, Deborah S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pool, Karl N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-03-01

A sand filter is used to help maintain water clarity at the K West Basin where highly radioactive sludge is stored. Eventually that sand filter will require disposal. The radionuclide content of the solids trapped in the sand filter will affect the selection of the sand filter disposal pathway. The Pacific Northwest National Laboratory (PNNL) was contracted by the K Basin Operations & Plateau Remediation Project (operations contractor CH2M Hill) to analyze the radionuclide content of the solids collected from the backwash of the K West Basin sand filter. The radionuclide composition in the sand filter backwash solids will be used by CH2M Hill to determine if the sand filter media and retained sludge solids will be designated as transuranic waste for disposal purposes or can be processed through less expensive means. On October 19, 2015, K Basin Operations & Plateau Remediation Project staff backwashed the sand filter into the North Load-Out Pit (NLOP) and immediately collected sample slurry from a sampling tube positioned 24 in. above the NLOP floor. The 764 g sand filter backwash slurry sample, KW-105 SFBW-001, was submitted to PNNL for analysis on October 20, 2015. Solids from the slurry sample were consolidated into two samples (i.e., a primary and a duplicate sample) by centrifuging and measured for mass (0.82 g combined – wet centrifuged solids basis) and volume (0.80 mL combined). The solids were a dark brown/orange color, consistent with iron oxide/hydroxide. The solids were dried; the combined dry solids mass was 0.1113 g, corresponding to 0.0146 weight percent (wt%) solids in the original submitted sample slurry. The solids were acid-digested using nitric and hydrochloric acids. Insoluble solids developed upon dilution with 0.5 M HNO₃, corresponding to an average 6.5 wt% of the initial dry solids content. The acid digestate and insoluble solids were analyzed separately by gamma spectrometry. Nominally, 7.7% of the ⁶⁰Co was present

Laboratory Test Setup for Cyclic Axially Loaded Piles in Sand

DEFF Research Database (Denmark)

Thomassen, Kristina; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

2017-01-01

This paper presents a comprehensive description and the considerations regarding the design of a new laboratory test setup for testing cyclic axially loaded piles in sand. The test setup aims at analysing the effect of axial one-way cyclic loading on pile capacity and accumulated displacements....... Another aim was to test a large diameter pile segment with dimensions resembling full-scale piles to model the interface properties between pile and sand correctly. The pile segment was an open-ended steel pipe pile with a diameter of 0.5 m and a length of 1 m. The sand conditions resembled the dense sand...... determined from the API RP 2GEO standard and from the test results indicated over consolidation of the sand. Two initial one-way cyclic loading tests provided results of effects on pile capacity and accumulated displacements in agreement with other researchers’ test results....

77 FR 51912 - Safety Zone; Tom Lyons Productions Fireworks, Long Island Sound, Sands Point, NY

Science.gov (United States)

2012-08-28

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 165 [Docket Number USCG-2012-0618] RIN 1625-AA00 Safety Zone; Tom Lyons Productions Fireworks, Long Island Sound, Sands Point, NY AGENCY.... 165.T01-0618 to read as follows: Sec. 165.T01-0618 Safety Zone; Tom Lyons Productions Fireworks, Long...

Potensi Pasir Lokal Tanjung Bintang Pada Aluminium Sand Casting Terhadap Porositas Produk Hasil Cor Aluminium

OpenAIRE

Hendronursito, Yusup; Prayanda, Yogi

2016-01-01

Green sand is one of the most important components in the process of metal casting. The sand in Indonesia region is varied level of subtlety, size of sand, and shape of sand. Green sand used in the process of metal casting is possible can affect the quality of casting product. This aims to determine the potential of Tanjung Bintang sand as green sand and the quality of the product in terms of porosity defects. The research was conducted by varying sand river from Tanjung Bintang and sand from...

External costs of sand mining in rivers: evidence from South Africa.

CSIR Research Space (South Africa)

De Lange, Willem J

2009-05-01

Full Text Available river sand load content and excluding the impacts of dams and sand mining). Accounting for the impacts of dams on sediment yield decreased the estimate by at least 33 percent (Theron et al., 2008). An aerial survey identified thirty-one active sand... mining operations, extracting approximately 400 000 cubic meters of sand per year (a conservative estimate) in the eThekwini area (Theron et al., 2008). The estimated remaining sediment yield from rivers after accounting for the impacts of dams...

Reports on 1974 result of Sunshine Project. Research on tar sand and oil shale; 1974 nendo tar sand oyobi oil shale ni kansuru chosa kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-04-04

The purpose of this research is to grasp the policy of the oil sand resource countries, the properties and existing conditions of the resources, effects of the oil sand resources on a long term energy supply/demand, etc., and to clarify the meaning and position of the researches on the development of oil sand resources in the future energy policy of Japan. The quantities of oil sand resources are mostly in the process of investigation except Alberta province of Canada and are estimated to be two trillion barrels. The quantity for which strip mining is possible is about 90 billion barrels, which are mostly located in the Athabasca region. The oil sand holding countries take a policy of positively developing oil sand. No barriers are particularly provided against the introduction of foreign technology and capital. Where the prospects are possible for the development of oil sand are Canada and Venezuela. R and D should be emphasized on the refining of bitumen and the extraction method within the oil reservoir. The investment per b/d is about 15-20 thousand dollars, which is likely to be more than twice as much as for the North Sea oilfields. The properties and quality of the synthetic crude oil are superior while the risk of exploitation is small; therefore, oil sand will be competitive with crude oil in the future. (NEDO)

Bacterial diversity of surface sand samples from the Gobi and Taklamaken deserts.

Science.gov (United States)

An, Shu; Couteau, Cécile; Luo, Fan; Neveu, Julie; DuBow, Michael S

2013-11-01

Arid regions represent nearly 30 % of the Earth's terrestrial surface, but their microbial biodiversity is not yet well characterized. The surface sands of deserts, a subset of arid regions, are generally subjected to large temperature fluctuations plus high UV light exposure and are low in organic matter. We examined surface sand samples from the Taklamaken (China, three samples) and Gobi (Mongolia, two samples) deserts, using pyrosequencing of PCR-amplified 16S V1/V2 rDNA sequences from total extracted DNA in order to gain an assessment of the bacterial population diversity. In total, 4,088 OTUs (using ≥97 % sequence similarity levels), with Chao1 estimates varying from 1,172 to 2,425 OTUs per sample, were discernable. These could be grouped into 102 families belonging to 15 phyla, with OTUs belonging to the Firmicutes, Proteobacteria, Bacteroidetes, and Actinobacteria phyla being the most abundant. The bacterial population composition was statistically different among the samples, though members from 30 genera were found to be common among the five samples. An increase in phylotype numbers with increasing C/N ratio was noted, suggesting a possible role in the bacterial richness of these desert sand environments. Our results imply an unexpectedly large bacterial diversity residing in the harsh environment of these two Asian deserts, worthy of further investigation.

Cyclic settlement behavior of strip footings resting on reinforced layered sand slope

Directory of Open Access Journals (Sweden)

Mostafa A. El Sawwaf

2012-10-01

Full Text Available The paper presents a study of the behavior of model strip footings supported on a loose sandy slope and subjected to both monotonic and cyclic loads. The effects of the partial replacement of a compacted sand layer and the inclusion of geosynthetic reinforcement were investigated. Different combinations of the initial monotonic loads and the amplitude of cyclic loads were chosen to simulate structures in which loads change cyclically such as machine foundations. The affecting factors including the location of footing relative to the slope crest, the frequency of the cyclic load and the number of load cycles were studied. The cumulative cyclic settlement of the model footing supported on a loose sandy slope, un-reinforced and reinforced replaced sand deposits overlying the loose slope were obtained and compared. Test results indicate that the inclusion of soil reinforcement in the replaced sand not only significantly increases the stability of the sandy slope itself but also decreases much both the monotonic and cumulative cyclic settlements leading to an economic design of the footings. However, the efficiency of the sand–geogrid systems depends on the properties of the cyclic load and the location of the footing relative to the slope crest. Based on the test results, the variation of cumulative settlements with different parameters is presented and discussed.

Microbial Characterization of Qatari Barchan Sand Dunes.

Directory of Open Access Journals (Sweden)

Sara Abdul Majid

Full Text Available This study represents the first characterization of sand microbiota in migrating barchan sand dunes. Bacterial communities were studied through direct counts and cultivation, as well as 16S rRNA gene and metagenomic sequence analysis to gain an understanding of microbial abundance, diversity, and potential metabolic capabilities. Direct on-grain cell counts gave an average of 5.3 ± 0.4 x 105 cells g-1 of sand. Cultured isolates (N = 64 selected for 16S rRNA gene sequencing belonged to the phyla Actinobacteria (58%, Firmicutes (27% and Proteobacteria (15%. Deep-sequencing of 16S rRNA gene amplicons from 18 dunes demonstrated a high relative abundance of Proteobacteria, particularly enteric bacteria, and a dune-specific-pattern of bacterial community composition that correlated with dune size. Shotgun metagenome sequences of two representative dunes were analyzed and found to have similar relative bacterial abundance, though the relative abundances of eukaryotic, viral and enterobacterial sequences were greater in sand from the dune closer to a camel-pen. Functional analysis revealed patterns similar to those observed in desert soils; however, the increased relative abundance of genes encoding sporulation and dormancy are consistent with the dune microbiome being well-adapted to the exceptionally hyper-arid Qatari desert.

Gassmann Modeling of Acoustic Properties of Sand-clay Mixtures

Science.gov (United States)

Gurevich, B.; Carcione, J. M.

The feasibility of modeling elastic properties of a fluid-saturated sand-clay mixture rock is analyzed by assuming that the rock is composed of macroscopic regions of sand and clay. The elastic properties of such a composite rock are computed using two alternative schemes.The first scheme, which we call the composite Gassmann (CG) scheme, uses Gassmann equations to compute elastic moduli of the saturated sand and clay from their respective dry moduli. The effective elastic moduli of the fluid-saturated composite rock are then computed by applying one of the mixing laws commonly used to estimate elastic properties of composite materials.In the second scheme which we call the Berryman-Milton scheme, the elastic moduli of the dry composite rock matrix are computed from the moduli of dry sand and clay matrices using the same composite mixing law used in the first scheme. Next, the saturated composite rock moduli are computed using the equations of Brown and Korringa, which, together with the expressions for the coefficients derived by Berryman and Milton, provide an extension of Gassmann equations to rocks with a heterogeneous solid matrix.For both schemes, the moduli of the dry homogeneous sand and clay matrices are assumed to obey the Krief's velocity-porosity relationship. As a mixing law we use the self-consistent coherent potential approximation proposed by Berryman.The calculated dependence of compressional and shear velocities on porosity and clay content for a given set of parameters using the two schemes depends on the distribution of total porosity between the sand and clay regions. If the distribution of total porosity between sand and clay is relatively uniform, the predictions of the two schemes in the porosity range up to 0.3 are very similar to each other. For higher porosities and medium-to-large clay content the elastic moduli predicted by CG scheme are significantly higher than those predicted by the BM scheme.This difference is explained by the fact

Guide to preparing SAND reports and other communication products.

Energy Technology Data Exchange (ETDEWEB)

2011-09-01

This guide describes the R&A process, Common Look and Feel requirements, and preparation and publishing procedures for communication products at Sandia National Laboratories. Samples of forms and examples of published communications products are provided. This guide takes advantage of the wealth of material now available on the Web as a resource. Therefore, it is best viewed as an electronic document. If some of the illustrations are too small to view comfortably, you can enlarge them on the screen as needed. The format of this document is considerably different than that usually expected of a SAND Report. It was selected to permit the large number of illustrations and examples to be placed closer to the text that references them. In the case of forms, covers, and other items that are included as examples, a link to the Web is provided so that you can access the items and download them for use. This guide details the processes for producing a variety of communication products at Sandia National Laboratories. Figure I-1 shows the general publication development process. Because extensive supplemental material is available from Sandia on the internal web or from external sources (Table I-1), the guide has been shortened to make it easy to find information that you need.

Using a sand wave model for optimal monitoring of navigation depth

NARCIS (Netherlands)

Knaapen, Michiel; Hulscher, Suzanne J.M.H.; Tiessen, Meinard C.H.; van den Berg, J.; Parker, G.; García, M.H.

2005-01-01

In the Euro Channel to Rotterdam Harbor, sand waves reduce the navigable depth to an unacceptable level. To avoid the risk of grounding, the navigation depth is monitored and sand waves that reduce the navigation depth unacceptably are dredged. After the dredging, the sand waves slowly regain their

Problems of bentonite rebonding of synthetic system sands in turbine mixers

Directory of Open Access Journals (Sweden)

A. Fedoryszyn

2008-12-01

Full Text Available Turbine (rotor mixers are widely used in foundries for bentonite rebonding of synthetic system sands. They form basic equipment in modern sand processing plants. Their major advantage is the short time of the rebond mixing cycle.Until now, no complete theoretical description of the process of mixing in turbine mixers has been offered. Neither does it seem reasonable to try to adapt the theoretical backgrounds of the mixing process carried out in mixers of other types, for example, rooler mixers [1], to the description of operation of the turbine mixers. Truly one can risk the statement that the individual fundamental operations of mixing in rooler mixers, like kneading, grinding, mixing and thinning, are also performed in turbine mixers. Yet, even if so, in turbine mixers these processes are proceeding at a rate and intensity different than in the roller mixers. The fact should also be recalled that the theoretical backgrounds usually relate to the preparation of sand mixtures from new components, and this considerably restricts the field of application of these descriptions when referred to rebond mixing of the system sand. The fundamentals of the process of the synthetic sand rebonding with bentonite require determination and description of operations, like disaggregation, even distribution of binder and water within the entire volume of the rebonded sand batch, sand grains coating, binder activation and aeration.This study presents the scope of research on the sand rebonding process carried out in turbine mixers. The aim has been to determine the range and specific values of the designing and operating parameters to get optimum properties of the rebonded sand as well as energy input in the process.

The oil sands: A new energy vision for Canada

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

Canada`s oil sands deposits were considered to offer huge potential for wealth generation and enduring social benefits. This report showed that putting in action the plan developed by the National Task Force on Oil Sands Strategies would help unlock this potential and realize the benefits; the forecast called for a doubling or tripling of oil sands production over the next 25 years. The plan should also predicted an increase in investments in oil sands since the fiscal regime would be stable and the product would be in increasing demand. New capital investment should generate significant environmental, social and economic benefits. The real outcome would be increased national prosperity, since further growth in investment would translate into thousands of skilled jobs across Canada, expansion of government revenues, and improvements to Canada`s trade balance. 1 ill.

The gravel sand transition in a disturbed catchment

Science.gov (United States)

Knighton, A. David

1999-03-01

More than 40 million cubic metres of mining waste were supplied to the Ringarooma River between 1875 and 1984, leading to successive phases of aggradation and degradation. The natural bed material is gravel but, given the volume of introduced load and the fact that much of the input was less than 5 mm in diameter, the size composition of the bed changed from gravel to sand during the phase of downstream progressive aggradation. A very sharp gravel-sand transition developed in which median grain size decreased from over 30 mm to under 3 mm in less than 500 m. With upstream supplies of mining debris becoming depleted first, degradation followed the same downstream progressive pattern as aggradation, causing the transition to migrate downstream. By 1984, the river could be regarded as a series of zones, each characterized by a particular bed condition: a natural cobble-gravel bed, unaffected by mining inputs (0-32 km); pre-disturbance bed re-exposed by degradation over 35-40 years (32-53 km); sandy substrate with a gravel armour produced by differential transport during degradation (53-65 km); sand dominated but with developing surface patches of coarser material (65-75 km); sandy bed reflecting the size composition of the original mining input (75-118 km). Although the gravel-sand transition itself is sharp, the transitional zone is lengthy (53-75 km). As degradation continues, the gravel-sand transition is expected to progress downstream but it has remained in a stable position for 12 years. Indeed, two major floods during the period released large quantities of sand from the sub-armour layer and newly-formed banks of mine tailings, causing fining both above and below the transition. Surface grain size is an adjustable component in the transitional zone as the river strives to recover from a major anthropogenic disturbance.

Electric conductivity for laboratory and field monitoring of induced partial saturation (IPS) in sands

Science.gov (United States)

Kazemiroodsari, Hadi

implemented in the prepared specimen to validate the numerical simulation model and explore the use of conductivity probes to detect the transport of chemical solution, estimate degree of saturation achieved due to injection of chemical solution, and evaluate final zone of partial saturation. The conductivity probe and the simulation results agreed well. To study the effect of IPS on liquefaction response of the sand specimen, IPS was implemented in a large (2-story high) sand specimen prepared in the laminar box of NEES Buffalo and then the specimen was subjected to harmonic shaking. Electric conductivity probes were used in the specimen treatment by controlling the duration and spacing of injection of the chemical solution, in monitoring the transport of chemical solution, in the estimation of zone of partial saturation achieved, and in the estimation of degree of saturation achieved due to implementation of IPS. The conductivity probes indicated partial saturation of the specimen. The shaking tests results confirmed the partial saturation state of the sand specimen. In addition, to the laboratory works, electric conductivity probes were used in field implementation of IPS in a pilot test at the Wildlife Liquefaction Array (WLA) of NEES UCSB site. The conductivity probes in the field test helped decide the optimum injection pressure, the injection tube spacing, and the degree of saturation that could be achieved in the field. The various laboratory and field tests confirmed that electric conductivity and the probes devised and used can be invaluable in the implementation of IPS, by providing information regarding transport of the chemical solution, the spacing of injection tubes, duration of injection, and the zone and degree of partial saturation caused by IPS.

40 CFR 91.113 - Requirement of certification-emission control information label and engine identification number.

Science.gov (United States)

2010-07-01

... control information label and engine identification number. 91.113 Section 91.113 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM... certification—emission control information label and engine identification number. (a) The engine manufacturer...

Supercritical solvent extraction of oil sand bitumen

Science.gov (United States)

Imanbayev, Ye. I.; Ongarbayev, Ye. K.; Tileuberdi, Ye.; Mansurov, Z. A.; Golovko, A. K.; Rudyk, S.

2017-08-01

The supercritical solvent extraction of bitumen from oil sand studied with organic solvents. The experiments were performed in autoclave reactor at temperature above 255 °C and pressure 29 atm with stirring for 6 h. The reaction resulted in the formation of coke products with mineral part of oil sands. The remaining products separated into SARA fractions. The properties of the obtained products were studied. The supercritical solvent extraction significantly upgraded extracted natural bitumen.

Estimation of Sand Production Rate Using Geomechanical and Hydromechanical Models

Directory of Open Access Journals (Sweden)

Son Tung Pham

2017-01-01

Full Text Available This paper aims to develop a numerical model that can be used in sand control during production phase of an oil and gas well. The model is able to predict not only the onset of sand production using critical bottom hole pressure inferred from geomechanical modelling, but also the mass of sand produced versus time as well as the change of porosity versus space and time using hydromechanical modelling. A detailed workflow of the modelling was presented with each step of calculations. The empirical parameters were calibrated using laboratory data. Then the modelling was applied in a case study of an oilfield in Cuu Long basin. In addition, a sensitivity study of the effect of drawdown pressure was presented in this paper. Moreover, a comparison between results of different hydromechanical models was also addressed. The outcome of this paper demonstrated the possibility of modelling the sand production mass in real cases, opening a new approach in sand control in petroleum industry.

Strength Characteristics of Quarry Dust in Replacement of Sand

Science.gov (United States)

Shyam Prakash, K.; Hanumantha Rao, Ch, Dr

2017-08-01

The replacement of natural fine aggregate by using quarry dust leads to consumption of generated quarry dust, the requirement of land fill area can be reduced and solves the natural sand scarcity problem. The sand availability as a fine aggregate at low cost which needs the reason to search as a alternative material. Even it causes saddle to dump the crusher dust at one place which causes environmental pollution. The chemical analysis, specific gravity, sieve analysis and compressive strength is identified for various percentage and grades of concrete by replacement of sand with quarry dust.

Holocene beach buildup and coastal aeolian sand incursions off the Nile littoral cell

Science.gov (United States)

Roskin, Joel; Sivan, Dorit; Shtienberg, Gilad; Porat, Naomi; Bookman, Revital

2017-04-01

Israel's coastal plain is abundant with sand originating from the Nile littoral cell. The inland windblown loose sand has formed 3-6 km wide lobe-like sand and dune fields currently comprised of foredunes, linear and northeasterly facing transverse and parabolic dunes that are currently stabilized by vegetation. This study reviews the architecture and history of the these dune fields aiming to: (a) Date the timings of beach accretion, and sand and dune incursions. (b) Discriminate between natural and human-induced forcing factors of sand mobilization and stabilization in time and space. (c) Present a model of the dunescape development. (d) Assess scenarios of sand transport in the future charcaterized by intense human impact and climate change. Luminescence ages, radiocarbon dates and relative ages from previously published geological and archaeological reports, historical texts, together with new optically stimulated luminescence (OSL) ages and stratigraphic and sedimentological data are analyzed. The deposition, mobilizations and preservation of the sand bodies, initially induced by the decline in sea level rise at 6-4 ka, were later controlled by historic land-use intensity and modern land-use/negligence practices. At 6 ka, beach sand buildup rapidly started. Where aeolianite ridges bordered the coast, pulses of sand with biogenic carbonate grains unconformably draped the ridges and rapidly consolidated into a distinct sandy calcarenite unit. Further east, sand sheets and low dunes partly pedogenized following their incursion, but did not cement. The water retention capacities of the sand sheets enabled the establishment of a sand-stabilizing vegetation cover that probably became an attractive environment for fuel and grazing. The growing Hellenistic-Roman-Byzantine ( 2.4-1.3 ka) populations probably led to increased consumption and massive destruction of sand stabilizing vegetation, enabling sand erodibility and mobilization during winter storms. The sand

Provenance of Coastal dune sands along Red Sea, Egypt

Indian Academy of Sciences (India)

26

accumulation of sands behind vegetation or any other obstacles. ... The study areas Safaga (SF) and Quseir (QS) field dunes (Fig. 1) ..... coastal dune sands were deposited in a passive margin of a synrift .... Sed Petrol 63(6), 1110-1117.

Frac Sand Mines Are Preferentially Sited in Unzoned Rural Areas.

Science.gov (United States)

Locke, Christina

2015-01-01

Shifting markets can cause unexpected, stochastic changes in rural landscapes that may take local communities by surprise. Preferential siting of new industrial facilities in poor areas or in areas with few regulatory restrictions can have implications for environmental sustainability, human health, and social justice. This study focuses on frac sand mining-the mining of high-quality silica sand used in hydraulic fracturing processes for gas and oil extraction. Frac sand mining gained prominence in the 2000s in the upper midwestern United States where nonmetallic mining is regulated primarily by local zoning. I asked whether frac sand mines were more commonly sited in rural townships without formal zoning regulations or planning processes than in those that undertook zoning and planning before the frac sand boom. I also asked if mine prevalence was correlated with socioeconomic differences across townships. After creating a probability surface to map areas most suitable for frac sand mine occurrence, I developed neutral landscape models from which to compare actual mine distributions in zoned and unzoned areas at three different spatial extents. Mines were significantly clustered in unzoned jurisdictions at the statewide level and in 7 of the 8 counties with at least three frac sand mines and some unzoned land. Subsequent regression analyses showed mine prevalence to be uncorrelated with land value, tax rate, or per capita income, but correlated with remoteness and zoning. The predicted mine count in unzoned townships was over two times higher than that in zoned townships. However, the county with the most mines by far was under a county zoning ordinance, perhaps indicating industry preferences for locations with clear, homogenous rules over patchwork regulation. Rural communities can use the case of frac sand mining as motivation to discuss and plan for sudden land-use predicaments, rather than wait to grapple with unfamiliar legal processes during a period of

Intermontane eolian sand sheet development, Upper Tulum Valley, central-western Argentina

Directory of Open Access Journals (Sweden)

Patrick Francisco Fuhr Dal' Bó

Full Text Available ABSTRACTThe intermontane Upper Tulum eolian sand sheet covers an area of ca. 125 km² at north of the San Juan Province, central-western Argentina. The sand sheet is currently an aggrading system where vegetation cover, surface cementation and periodic flooding withhold the development of dunes with slipfaces. The sand sheet surface is divided into three parts according to the distribution of sedimentary features, which reflects the variation in sediment budget, water table level and periodic flooding. The central sand sheet part is the main area of eolian deposition and is largely stabilized by vegetation. The sedimentary succession is 4 m thick and records the vertical interbedding of eolian and subaqueous deposits, which have been deposited for at least 3.6 ky with sedimentation rates of 86.1 cm/ky. The construction of the sand sheet is associated with deflation of the sand-graded debris sourced by San Juan alluvial fan, which is available mainly in drier fall-winter months where water table is lower and wind speeds are periodically above the threshold velocity for sand transport. The accumulation of sedimentary bodies occurs in a stabilized eolian system where vegetation cover, thin mud veneers and surface cementation are the main agents in promoting accumulation. The preservation of the sand sheet accumulations is enabled by the progressive creation of the accommodation space in a tectonically active basin and the continuous burial of geological bodies favored by high rates of sedimentation.

Using the SAND-II and MLM methods to reconstruct fast neutron spectra

International Nuclear Information System (INIS)

Bondars, Kh.Ya.; Kamnev, V.A.; Lapenas, A.A.; Troshin, V.S.

1981-01-01

The reconstruction of fast neutron spectra from measured reaction rates may be reduced to the solution of Fredholm's integral equation of the first kind. This problem falls in the category of incorrectly formulated problems, and so additional information is required concerning the unknown function i.e. concerning the differential energy dependence of the neutron, flux density sup(phi)(E). There are various methods for seeking a solution to the problem as formulated above. One of the best-known methods used in the USSR is the maximum likelihood method (MLM) (or directional difference method (DDM)), whereas SAND-II is commonly used abroad. The purpose of this paper is to compare the MLM and SAND-II methods, taking as an example the processing of measurement data which were obtained in the B-2 beam line at the BR-10 reactor in order to determine the composition of shielding for a fast reactor

Information manager vol 10

African Journals Online (AJOL)

Library _info_Sc_ 1

The Perception of Librarians As Sources Of Information On HIV/AIDS By ... the librarian is confined to the library. ... is to offer information services that can assist information users to meet their needs at the right time and in the right format. ... relationships (Sande and Volbering,1992). ..... Education for Students: A Proposal for.

Test Setup for Axially Loaded Piles in Sand

DEFF Research Database (Denmark)

Thomassen, Kristina

The test setup for testing axially static and cyclic loaded piles in sand is described in the following. The purpose for the tests is to examine the tensile capacity of axially loaded piles in dense fully saturated sand. The pile dimensions are chosen to resemble full scale dimension of piles used...... in offshore pile foundations today....

Report and recommendations of the task force on tree and shrub planting on active oil sands tailings dams

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-02-15

In oil sands reclamation operations in Canada there is a conflict between dam safety and the planting of trees and woody shrubs. Indeed, tree planting is being restricted on the downstream slopes of dams to avoid damage to drains and to ensure the integrity of visual and instrumentation monitoring conflicting thus with progressive reclamation. Alberta Environment hired the Oil Sands Research and Information Network (OSRIN), an independent organization which analyzes and interprets available knowledge on soil and water reclamation in the oil sands mining sector, to address this issue and make recommendations. The organization appointed a Task Force which presented its final report in March 2011. The Task Force recommended that the Engineer of Record should be responsible for determining the tree and shrub planting zones and that he should submit his plans to Alberta Environment for approval.

Constitutive Soil Properties for Mason Sand and Kennedy Space Center

Science.gov (United States)

Thomas, Michael A.; Chitty, Daniel E.

2011-01-01

Accurate soil models are required for numerical simulations of land landings for the Orion Crew Exploration Vehicle (CEV). This report provides constitutive material models for two soil conditions at Kennedy Space Center (KSC) and four conditions of Mason Sand. The Mason Sand is the test sand for LaRC s drop tests and swing tests of the Orion. The soil models are based on mechanical and compressive behavior observed during geotechnical laboratory testing of remolded soil samples. The test specimens were reconstituted to measured in situ density and moisture content. Tests included: triaxial compression, hydrostatic compression, and uniaxial strain. A fit to the triaxial test results defines the strength envelope. Hydrostatic and uniaxial tests define the compressibility. The constitutive properties are presented in the format of LSDYNA Material Model 5: Soil and Foam. However, the laboratory test data provided can be used to construct other material models. The soil models are intended to be specific to the soil conditions they were tested at. The two KSC models represent two conditions at KSC: low density dry sand and high density in-situ moisture sand. The Mason Sand model was tested at four conditions which encompass measured conditions at LaRC s drop test site.

Evaluation of multistage filtration to reduce sand filter exhaust activity

International Nuclear Information System (INIS)

Zippler, D.B.

1975-01-01

Air from the Savannah River Plant Fuel Reprocessing facilities is filtered through deep bed sand filters consisting of 8 1 / 2 feet of gravel and sand. These filters have performed satisfactorily for the past 18 years in maintaining radioactive release levels to a minimum. The apparent filter efficiency has been determined for many years by measurements of the quantity of radioactivity in the air stream before and after the filter. Such tests have indicated efficiencies of 99.9 percent or better. Even with sand filter efficiency approaching a single stage HEPA filter, new emphasis on further reduction in release of plutonium activity to the environment prompted a study to determine what value backup HEPA filtration could provide. To evaluate the specific effect additional HEPA filtration would have on the removal of Pu from the existing sand filter exhaust stream, a test was conducted by passing a sidestream of sand-filtered air through a standard 24 x 24 x 11 1 / 2 in. HEPA filter. Isokinetic air samples were withdrawn upstream and downstream of the HEPA filter and counted for alpha activity. Efficiency calculations indicated that backup HEPA filtration could be expected to provide an additional 99 percent removal of the Pu activity from the present sand-filter exhaust. (U.S.)

Canada's oil sands: nuclear power in an integrated energy economy

Energy Technology Data Exchange (ETDEWEB)

Isaacs, E. [Alberta Energy Research Inst., Calgary, Alberta (Canada)

2008-07-01

This paper discusses the role of nuclear power in Canada's oil sands industry. It outlines the oil sands resource in Alberta and the various industrial projects to recover the oil from the tar sands. It points to continuing innovation in technology since the 1930's. The hydrogen required for upgrading bitumen is made from natural gas. Finally, it discusses the next wave of oil sands production technologies.

Laboratory test on maximum and minimum void ratio of tropical sand matrix soils

Science.gov (United States)

Othman, B. A.; Marto, A.

2018-04-01

Sand is generally known as loose granular material which has a grain size finer than gravel and coarser than silt and can be very angular to well-rounded in shape. The present of various amount of fines which also influence the loosest and densest state of sand in natural condition have been well known to contribute to the deformation and loss of shear strength of soil. This paper presents the effect of various range of fines content on minimum void ratio e min and maximum void ratio e max of sand matrix soils. Laboratory tests to determine e min and e max of sand matrix soil were conducted using non-standard method introduced by previous researcher. Clean sand was obtained from natural mining site at Johor, Malaysia. A set of 3 different sizes of sand (fine sand, medium sand, and coarse sand) were mixed with 0% to 40% by weight of low plasticity fine (kaolin). Results showed that generally e min and e max decreased with the increase of fines content up to a minimal value of 0% to 30%, and then increased back thereafter.

Mineralogy and Genesis of Heavy Minerals in Coastal Dune Sands, South Eastern Qatar

OpenAIRE

Nasir, Sobhi J. [صبحي جابر نصر; El-Kassas, Ibrahim A.; Sadiq, A. Ali M.

1999-01-01

Large amounts of aeolian sand occur in the southeastern coastal zone of Qatar Peninsula as sand dunes accumulated in a vast sand field locally called " Niqyan Qatar ". The present work, carried out on a sand dune belt of this field near Mesaied Industrial City, revealed the distribution of heavy minerals shows a regional variability induced by provenance and local variability reflecting genetic differences. The studied dune sands are rich in shells of pelecypods, with the light mineral assemb...

Sand Needs and Resources Offshore New York

Science.gov (United States)

Lashley, J. M.; Flood, R. D.; White, M.; Bokuniewicz, H.; Hinrichs, C.; Wilson, R. E.

2016-02-01

"Superstorm" Sandy (October, 2012) accentuated the persistent problem of coastal erosion on New York's ocean coast. The New York state Department of State in cooperation with the Bureau of Ocean Energy Management has initiated further identification and assessment of marine sand reserves required to improve the resiliency of coastal communities and the maintenance of coastal habitats. The historical demand for beach nourishment has been about 1.5 million cubic meters per year, but sea level rise and the occurrence of extreme conditions may increase the demand to over 5 million cubic meters annually. Forty-four historical and proposed borrow sites have been delineated. This inner shelf is both sand rich and data rich. Geophysical and geological data has been compiled and reassessed to support identification, characterization, and delineation of sand resources for potential use in future coastal restoration, beach nourishment, and/or wetland restoration efforts. The South Shore of Long Island is composed in part by the Fire Island National Seashore. Holocene sand ridges extending at an oblique angle to the cross shore in the seaward direction. Borrow pits among the sand ridges, excavated were apparent in the most recent surveys and it appears that natural replenishment of offshore borrow areas has been occurring although the rates need to be determined in order to assess their sustainability. Not only is the area one of intense societal attention, but the use of this resource for coastal resilience must fit into a diverse framework marine spatial planning including not only traditional components, like commercial fishing, but also new factors like the siting of offshore wind-farms. To extend this assessment will include a recent survey, sponsored by the Bureau of Ocean Energy Management and the New York Department of State, providing approximately 700 km of geophysical survey lines located between 3 and 9 nautical miles offshore, and 46 geotechnical samples

Modeling fine-scale geological heterogeneity-examples of sand lenses in tills

DEFF Research Database (Denmark)

Kessler, Timo Christian; Comunian, Alessandro; Oriani, Fabio

2013-01-01

that hamper subsequent simulation. Transition probability (TP) and multiple-point statistics (MPS) were employed to simulate sand lens heterogeneity. We used one cross-section to parameterize the spatial correlation and a second, parallel section as a reference: it allowed testing the quality......Sand lenses at various spatial scales are recognized to add heterogeneity to glacial sediments. They have high hydraulic conductivities relative to the surrounding till matrix and may affect the advective transport of water and contaminants in clayey till settings. Sand lenses were investigated...... on till outcrops producing binary images of geological cross-sections capturing the size, shape and distribution of individual features. Sand lenses occur as elongated, anisotropic geobodies that vary in size and extent. Besides, sand lenses show strong non-stationary patterns on section images...

Evaluation of Augmented REality Sandtable (ARES) during Sand Table Construction

Science.gov (United States)

2018-01-01

sand table, ARES, resulted in significantly higher- quality ratings overall for the terrain model based on a global rating scale, as well as...dependent measures in this study. Sand Table Construction Score Card: A 5-point Likert scale was used to identify the accuracy and quality of required...reproduced on the sand table. The quality of the map reproduced was evaluated using standard procedures of the map-drawing paradigm, such as that

The Rheology of Acoustically Fluidized Sand

Science.gov (United States)

Conrad, J. W.; Melosh, J.

2013-12-01

The collapse of large craters and the formation of central peaks and peak rings is well modeled by numerical computer codes that incorporate the acoustic fluidization mechanism to temporarily allow the fluid-like flow of rock debris immediately after crater excavation. Furthermore, long runout landslides require a similar mechanism to explain their almost frictionless movement, which is probably also a consequence of their granular composition coupled with internal vibrations. Many different investigators have now confirmed the ability of vibrations to fluidize granular materials. Yet it still remains to fully describe the rheology of vibrated sand as a function of stress, frequency and amplitude of the vibrations in the sand itself. We constructed a rotational viscometer to quantitatively investigate the relation between the stress and strain rate in a horizontal bed of strongly vibrated sand. In addition to the macroscopic stain rate, the amplitude and frequency of the vibrations produced by a pair of pneumatic vibrators were also measured with the aid of miniaturized piezoelectric accelerometers (B&K 4393) whose output was recorded on a digital storage oscilloscope. The initial gathering of the experimental data was difficult due to granular memory, but by having the sand compacted vibrationally for 8 minutes before each run the scatter of data was reduced and we were able to obtain consistent results. Nevertheless, our major source of uncertainty was variations in strain rate from run to run. We find that vibrated sand flows like a highly non-Newtonian fluid, in which the shear strain rate is proportional to stress to a power much greater than one, where the precise power depends on the amplitude and frequency of the applied vibrations. Rapid flow occurs at stresses less than half of the static yield stress (that is, the yield stress when no vibration is applied) when strong vibrations are present. For a Newtonian fluid, such as water, the relation between

Mineral sands

International Nuclear Information System (INIS)

Anon.

1990-01-01

This paper presents an outlook of the Australian mineral sand industry and covers the major operators. It is shown that conscious of an environmentally minded public, the Australian miners have led the way in the rehabilitation of mined areas. Moreover the advanced ceramic industry is generating exciting new perspectives for zircon producers and there is a noticeable growth in the electronic market for rare earths, but in long term the success may depend as much on environmental management and communication skills as on mining and processing skills

Experimental Study on Unconfined Compressive Strength of Organic Polymer Reinforced Sand

Directory of Open Access Journals (Sweden)

Jin Liu

2018-01-01

Full Text Available The natural sand is loose in structure with a small cohesive force. Organic polymer can be used to reinforce this sand. To assess the effectiveness of organic polymer as soil stabilizer (PSS, a series of unconfined compressive strength tests have been performed on reinforced sand. The focus of this study was to determine a curing method and a mix design to stabilize sand. The curing time, PSS concentration, and sand density were considered as variables in this study. The reinforcement mechanism was analyzed with images of scanning electron microscope (SEM. The results indicated that the strength of stabilized sand increased with the increase in the curing time, concentration, and sand density. The strength plateaus are at about curing time of 48 h. The UCS of samples with density of 1.4 g/cm3 at 10%, 20%, 30%, 40%, and 50% PSS concentration are 62.34 kPa, 120.83 kPa, 169.22 kPa, 201.94 kPa, and 245.28 kPa, respectively. The UCS of samples with PSS concentration of 30% at 1.4 g/cm3, 1.5 g/cm3, and 1.6 g/cm3 density are 169.22 kPa, 238.6 kPa 5, and 281.69 kPa, respectively. The chemical reaction between PSS and sand particle is at its microlevel, which improves the sand strength by bonding its particles together and filling the pore spaces. In comparison with the traditional reinforcement methods, PSS has the advantages of time saving, lower cost, and better environment protection. The research results can be useful for practical engineering applications, especially for reinforcement of foundation, embankment, and landfill.

Selected parameters of moulding sands for designing quality control systems

Directory of Open Access Journals (Sweden)

J. Jakubski

2010-07-01

Full Text Available One of the modern methods of production optimisation are artificial neural networks. Neural networks owe their popularity to the fact thatthey are convenient tools, which can be utilised in a wide scope of problems. They are capable of reflecting complex functions. Especiallytheir non-linearity should be emphasised. They are gaining wider and wider application in the foundry industry, among others, to controlmelting processes in cupolas and arc furnaces, designing castings and supply systems, control of moulding sands treatments, prediction ofproperties of cast alloys as well as selecting die casting.An attempt of the application neural networks to the quality control of moulding sands with bentonite is presented in the paper. This isa method of assessing the suitability of moulding sands by finding correlations in between individual parameters, by means of artificialneural network systems. The presented investigations were performed with the application of the Statistica 8.0 program.The investigations were aimed at the selection of the proper kind of a neural network for prediction a sand moistness on the bases ofcertain moulding sand properties such as: permeability, compactibility and friability. These parameters – determined as sand moistness functions - were introduced as initial parameters.Application of the Statistica program allowed for an automatic selection of the most suitable network for the reflection of dependencies and interactions existing among the proposed parameters. The best results were obtained for unidirectional multi-layer perception network (MLP. The neural network sensitivity to individual moulding sand parameters was determined, which allowed to reject not important parameters when constructing the network.

PROSPECTS FOR APPLICATION OF COMPLEX-MODIFIED SAND ASPHALT CONCRETE IN ROAD CONSTRUCTION

Directory of Open Access Journals (Sweden)

D. Yu. Alexandrov

2017-01-01

Full Text Available The paper considers a possibility to use sand asphalt concrete as a material for protection of asphalt concrete and cement concrete road pavements against affection of external destructive factors. Advantages and disadvantages of sand asphalt concrete road pavements have been determined in the paper. The paper provides recommendations on improvement of sand asphalt concrete properties and contains an analysis of possible variants for usage of complex-modified sand asphalt concrete in the road construction. It has been noted that according to its potentially possible physical and mechanical properties activated quartz sand being micro-reinforced by dispersive industrial wastes is considered as an efficient component for creation of constructive layers in road asphalt concrete pavements. The paper reveals only specific aspects of the efficient application of quartz sand in road asphalt concrete. The subject of the paper loоks rather interesting for regions where there are no rock deposits for obtaining broken-stone ballast but there is rather significant spreading of local quarts sand. Its successful application is connected with the necessity to develop special equipment for physical and chemical activation of sand grain surface that permits strongly to increase an adhesive strength in the area of phase separation within the “bitumen–SiO2” system. The considered problem is a topical one and its solution will make it possible to local sand in a maximum way and partially to exclude application of broken stone in road construction.

Influence of Reclamation Process on the Ecological Quality of Reclaim Sand

Directory of Open Access Journals (Sweden)

Dereń M.

2017-12-01

Full Text Available In this article, there were presented results of research on influence of reclamation process on the ecological quality of reclaim sand with furan resin used in nonferrous foundry. The quality of reclaimed sand is mainly define by two group of chemical substances from elution of reclaimed sand: Dissolves Organic Carbon (DOC and Total Dissolves Solids (TDS. Reclaimed sand used in test was prepared in experimental thermal reclaimer and mechanical vibration reclaimer REGMAS installed in Faculty of Foundry Engineering at University Of Science and Technology in Krakow. The reference point is molding sand shaking out and crumble in jaw crusher. Test of elution was made in accredited laboratory in Center For Research and Environmental Control in Katowice up to the standard with Dissolves Organic Carbon (DOC - PN-EN 1484:1999; Total Dissolves Solids (TDS - PN-EN 15216:2010. The standard for elution test is PN-EN 12457- 4:2006. Except that we were made loss of ignition test, to check how many resin was rest on sand grains.

Interactions between microbial activity and distribution and mineral coatings on sand grains from rapid sand filters treating groundwater

DEFF Research Database (Denmark)

Gülay, Arda; Tatari, Karolina; Musovic, Sanin

Rapid sand filtration is a traditional and widespread technology for drinking water purification which combines biological, chemical and physical processes together. Granular media, especially sand, is a common filter material that allows several oxidized compounds to accumulate on its surface....... Preliminarily, we detected a strong relation between the amount of DNA and mineral coating mass. We hypothesized that the accumulated mineral coatings have a positive effect on amount of bacterial biomass, its spatial distribution and substrate removal rates. In this study, we combined molecular, microscopic...

The extraction of bitumen from western tar sands. Annual report, July 1990--July 1991

Energy Technology Data Exchange (ETDEWEB)

Oblad, A.G.; Bunger, J.W.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1992-04-01

Contents of this report include the following: executive summary; characterization of the native bitumen from the Whiterocks oil sand deposit; influence of carboxylic acid content on bitumen viscosity; water based oil sand separation technology; extraction of bitumen from western oil sands by an energy-efficient thermal method; large- diameter fluidized bed reactor studies; rotary kiln pyrolysis of oil sand; catalytic upgrading of bitumen and bitumen derived liquids; ebullieted bed hydrotreating and hydrocracking; super critical fluid extraction; bitumen upgrading; 232 references; Appendix A--Whiterocks tar sand deposit bibliography; Appendix B--Asphalt Ridge tar sand deposit bibliography; and Appendix C--University of Utah tar sands bibliography.

Basic study on the estimating the value of sand beach using amenities replace

OpenAIRE

Shin, B-S; Kim, K-H.

2013-01-01

The sand beach along the east coast of Korea offers beautiful scenery with high-quality sand for leisure, and is also famous for white-sand and pine-trees both of which are important scenic resources. Furthermore, the sand beach helps to maintain natural environment of the coastal area and has the function of a disaster prevention system against high waves. There are two major value evaluation methods, Travel Cost Method and Contingent Valuation Method, to assess the value of sand beach. Cont...

Water management challenges and perspective for surface oil sands operations in North Eastern Alberta

International Nuclear Information System (INIS)

MacKinnon, M.

2009-01-01

Oil sands waters has many sources, such as raw water inputs (import water and hydrologic waters); oil sands ore water such as formation water; and oil sands process-affected water (OSPW) such as produced water and released water from tailings. This presentation demonstrated the importance of water to oil sands operations and indicated how oil sands processing affects water quality. Water imports to meet oil sands needs is a topic of particular interest. Other topics that were presented included water properties changing during oil sands operations; tailings management and the effects on water quality; oil sands tailings and water management and the impact on water quality of the region; how oil sands processing affected water quality; and current tailings approach and proposed new tailings methods and the effects on water composition. Post extraction changes in OSPW and the potential impacts of engineered tailings were also discussed. It was concluded that water treatment options must meet water management objectives. figs.

Computer aided vertebral visualization and analysis: a methodology using the sand rat, a small animal model of disc degeneration

Directory of Open Access Journals (Sweden)

Hanley Edward N

2003-03-01

Full Text Available Abstract Background The purpose of this study is to present an automated system that analyzes digitized x-ray images of small animal spines identifying the effects of disc degeneration. The age-related disc and spine degeneration that occurs in the sand rat (Psammomys obesus has previously been documented radiologically; selected representative radiographs with age-related changes were used here to develop computer-assisted vertebral visualization/analysis techniques. Techniques presented here have the potential to produce quantitative algorithms that create more accurate and informative measurements in a time efficient manner. Methods Signal and image processing techniques were applied to digitized spine x-ray images the spine was segmented, and orientation and curvature determined. The image was segmented based on orientation changes of the spine; edge detection was performed to define vertebral boundaries. Once vertebrae were identified, a number of measures were introduced and calculated to retrieve information on the vertebral separation/orientation and sclerosis. Results A method is described which produces computer-generated quantitative measurements of vertebrae and disc spaces. Six sand rat spine radiographs illustrate applications of this technique. Results showed that this method can successfully automate calculation and analysis of vertebral length, vertebral spacing, vertebral angle, and can score sclerosis. Techniques also provide quantitative means to explore the relation between age and vertebral shape. Conclusions This method provides a computationally efficient system to analyze spinal changes during aging. Techniques can be used to automate the quantitative processing of vertebral radiographic images and may be applicable to human and other animal radiologic models of the aging/degenerating spine.

Modeling sheet-flow sand transport under progressive surface waves

NARCIS (Netherlands)

Kranenburg, Wouter

2013-01-01

In the near-shore zone, energetic sea waves generate sheet-flow sand transport. In present day coastal models, wave-induced sheet-flow sand transport rates are usually predicted with semi-empirical transport formulas, based on extensive research on this phenomenon in oscillatory flow tunnels.

Pathogen removal using saturated sand colums supplemented with hydrochar

NARCIS (Netherlands)

Chung, J.W.

2015-01-01

This PhD study has evaluated hydrochars derived from biowastes as adsorbents for pathogen removal in water treatment. Pathogen removal experiments were conducted by carrying out breakthrough analysis using a simple sand filtration set-up. Glass columns packed by 10 cm sand bed supplemented with

Improvement of composition of core sand and molding sand mixtures for power machine building castings

International Nuclear Information System (INIS)

Velikanov, G.F.; Primak, I.N.; Brechko, A.A.

1982-01-01

Considered is a problem of development and improvement of mixtures, as well as of antisticking coatings with the given parameters providing production of castings of the necessary quality. Requirements to properties of mixtures and antisticking coatings are formulated proceeding from the conditions of guaranteed production of qualitative steel castings with mass from 0.5 up to 20t and wall thickness from 60 up to 200 mm. Formation of film structure of binding compositions is studied, their marginal contact angle and surface tension are determined. In the result of work carried out on improvement of core sand and molding sand mixtures the labour productivity during the production of core and moldings has been increased in 20-25% in average, the quality has also been improved [ru

Salinity and solvent effects on the characterization of naphthenic acids from Athabasca oil sands using electrospray ionization

International Nuclear Information System (INIS)

Headley, J.; Peru, K.; Barrow, M.; Derrick, P.

2010-01-01

This study investigated the salinity and solvent effects on the characterization of naphthenic acids (NA) in oil sands. The mass spectra of NA were obtained using an electrospray ionization method combined with a Fourier transform ion cyclotron resonance (FT-ICR) mass spectrometer. The study showed that while monocarboxylic compounds (C n H 2n+z O 2 ) in the z=-4, -6, and -12 of the 2,3 and 6-ring NA in the carbon number range of 13 to 19 were prevalent in the dichloromethane and acetonitrile co-solvent systems, the addition of salt resulted in a reduction of the observed species, the complete elimination of dicarboxylic acids, and an 80 per cent reduction in O 3 species with similar carbon number range and z values. The dicarboxylic acids were also less toxic than monocarboxylic acids. Results of the study will be used to refine methods of remediating oil sands and process water contaminated soils.

Coastal geology and recent origins for Sand Point, Lake Superior

Science.gov (United States)

Fisher, Timothy G.; Krantz, David E.; Castaneda, Mario R.; Loope, Walter L.; Jol, Harry M.; Goble, Ronald J.; Higley, Melinda C.; DeWald, Samantha; Hansen, Paul

2014-01-01

Sand Point is a small cuspate foreland located along the southeastern shore of Lake Superior within Pictured Rocks National Lakeshore near Munising, Michigan. Park managers’ concerns for the integrity of historic buildings at the northern periphery of the point during the rising lake levels in the mid-1980s greatly elevated the priority of research into the geomorphic history and age of Sand Point. To pursue this priority, we recovered sediment cores from four ponds on Sand Point, assessed subsurface stratigraphy onshore and offshore using geophysical techniques, and interpreted the chronology of events using radiocarbon and luminescence dating. Sand Point formed at the southwest edge of a subaqueous platform whose base is probably constructed of glacial diamicton and outwash. During the post-glacial Nipissing Transgression, the base was mantled with sand derived from erosion of adjacent sandstone cliffs. An aerial photograph time sequence, 1939–present, shows that the periphery of the platform has evolved considerably during historical time, infl uenced by transport of sediment into adjacent South Bay. Shallow seismic refl ections suggest slump blocks along the leading edge of the platform. Light detection and ranging (LiDAR) and shallow seismic refl ections to the northwest of the platform reveal large sand waves within a deep (12 m) channel produced by currents fl owing episodically to the northeast into Lake Superior. Ground-penetrating radar profi les show transport and deposition of sand across the upper surface of the platform. Basal radiocarbon dates from ponds between subaerial beach ridges range in age from 540 to 910 cal yr B.P., suggesting that Sand Point became emergent during the last ~1000 years, upon the separation of Lake Superior from Lakes Huron and Michigan. However, optically stimulated luminescence (OSL) ages from the beach ridges were two to three times as old as the radiocarbon ages, implying that emergence of Sand Point may have begun

Penggunaan Unit Slow Sand Filter, Ozon Generator dan Rapid Sand Filter Skala Rumah Tangga Untuk Meningkatkan Kualitas Air Sumur Dangkal Menjadi Air Layak Minum (Parameter Zat Organik dan Deterjen

Directory of Open Access Journals (Sweden)

Anindya Prawita Sari

2014-09-01

Full Text Available Air sumur merupakan air tanah yang sering kali digunakan masyarakat untuk aktivitas sehari-hari. Air sumur dengan kadar organik dan deterjen tinggi tidak layak dikonsumsi masyarakat karena dapat menyebabkan berbagai macam penyakit. Selain itu, adanya zat organik dan deterjen mempengaruhi warna dan bau air sumur sehingga tidak layak konsumsi. Slow sand filter merupakan unit pengolahan yang mampu meremoval zat organik pada air. Slow sand filter dan rapid sand filter tidak menggunakan bahan kimia dalam proses pengolahan sehingga lebih ekonomis dan efektif. Sedangkan ozon, efektif digunakan untuk meremoval zat organik yang ada dalam air dengan mengubah rantai zat organik menjadi lebih sederhana. Tujuan penelitian ini adalah untuk mengetahui keefektifan penggunaan slow sand filter, ozon generator dan rapid sand filter dalam menyisihkan beban deterjen dan zat organik pada air sumur. Hasil penelitian menunjukkan bahwa efisiensi removal pada unit slow sand filter untuk beban organik dan deterjen sebesar 57,6% dan 60,5 %, pada unit ozonasi sebesar 47,4% dan 17,5%, dan pada unit rapid sand filter sebesar 50,0% dan 50,9 %.

Upward migration of radio-cesium and strontium in a sand-filled lysimeter

International Nuclear Information System (INIS)

Sanford, W.E.; Larsen, I.L.; McConnell, J.W.; Rogers, R.D.

1998-01-01

The upward migration of 134 Cs, 137 Cs, and 90 Sr was observed in a silica sand-filled lysimeter at the Field Lysimeter Investigations: Low Level Waste Data Base Development experiment site at Oak Ridge National Laboratory. The source of the radionuclides first observed on the surface was identified from isotopic analysis as being from the buried waste. Cores of the sand were collected and analyzed for the vertical distribution of the radionuclides. Results of analyses revealed that pulses (elevated levels) in the activity of the Cs and Sr radioisotopes occurred at the same depths. During the sectioning of the sand core collected from directly above the buried waste form it was discovered that a fine root from an unidentified plant was present throughout all but the upper few centimeters of the core. Because the upward migration was unexpected, information that may lead to the determination of a definitive mechanism of migration was not preserved. The distribution of the radionuclides coupled with the presence of the root suggest that Cs and Sr migrated upward in the evapotranspiration stream of the root. Further study must be undertaken to confirm this phenomenon. Upward migration of radionuclides as observed here could result in direct exposures and offsite releases from underground storage facilities. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

Mix proportioning and performance of a crushed limestone sand-concrete

OpenAIRE

Makhloufi Zoubir; Bouziani Tayeb; Bédérina Madani; Hadjoudja Mourad

2014-01-01

Satisfying the ever-growing demand of concrete aggregates poses a problem in many parts of the world due to shortage of natural sand. Moreover, to conserve natural resources and protect civil engineering infrastructures, there is a need to find alternative materials. Crushed stone sand has been identified as a potential substitute material for natural sand in making good quality concrete. The main objective of the present investigation is to determine an adequate mix design method and evaluat...

Effects of sand burial on dew deposition on moss soil crust in a revegetated area of the Tennger Desert, Northern China

Science.gov (United States)

Jia, Rong-liang; Li, Xin-rong; Liu, Li-chao; Pan, Yan-xia; Gao, Yan-hong; Wei, Yong-ping

2014-11-01

Sand burial and dew deposition are two fundamental phenomena profoundly influencing biological soil crusts in desert areas. However, little information is available regarding the effects of sand burial on dew deposition on biological soil crusts in desert ecosystems. In this study, we evaluated the effects of sand burial at depths of 0 (control), 0.5, 1, 2 and 4 mm on dew formation and evaporation of three dominant moss crusts in a revegetated area of the Tengger Desert (Northern China) in 2010. The results revealed that sand burial significantly decreased the amount of dew deposited on the three moss crust types by acting as a semi-insulator retarding the dew formation and evaporation rates. The changes in surface temperature cannot fully explain the variations of the formation and evaporation rates of dew by moss crusts buried by sand. The extension of dew retention time was reflected by the higher dew ratios (the ratio of dew amount at a certain time to the maximum value in a daily course) in the daytime, and may to some extent have acted as compensatory mechanisms that diminished the negative effects of the reduction of dew amount induced by sand burial of moss crusts. The resistances to reduction of dewfall caused by sand burial among the three moss crusts were also compared and it was found that Bryum argenteum crust showed the highest tolerance, followed by crusts dominated by Didymodon vinealis and Syntrichia caninervis. This sequence corresponds well with the successional order of the three moss crusts in the revegetated area, thereby suggesting that resistance to reduction of dewfall may act as one mechanism by which sand burial drives the succession of moss crusts in desert ecosystems. This side effect of dew reduction induced by sand burial on biological soil crusts should be considered in future ecosystem construction and management of desert area.

A Life Cycle Assessment of Silica Sand: Comparing the Beneficiation Processes

Directory of Open Access Journals (Sweden)

Anamarija Grbeš

2015-12-01

Full Text Available Silica sand or quartz sand is a mineral resource with a wide variety of application; glass industry, construction and foundry are the most common examples thereof. The Republic of Croatia has reserves of 40 million tons of silica sand and a long tradition of surface mining and processing. The average annual production of raw silica sand in Croatia in the period from 2006 to 2011 amounted to 150 thousand tons. This paper presents cradle to gate LCA results of three different types of beneficiation techniques: electrostatic separation; flotation; gravity concentration. The aim of this research is to identify and quantify the environmental impacts of the silica sand production, to learn the range of the impacts for different processing methods, as well as to identify the major contributors and focus for further process design development.

The study of heavy metals leaching from waste foundry sands using a one-step extraction

Science.gov (United States)

Bożym, Marta

2017-10-01

There are a number of leaching test which are used to evaluate the effect of foundry waste disposal on the environment (TCLP, SPLP, ASTM at al.). Because the spent foundry sand are usually deposited at the ground level and they have a similar structure to the soil, survey mobility of metals using the same methods seems appropriate. One-step extraction allows for the evaluation of the mobility and bioavailability of metals in soil and waste. Waste foundry sands have been successfully used as a component in manufactured soils in U.S., but concern over metal contamination must be eliminated before considering this direction of use. The study evaluated the leaching of heavy metals (Cd, Pb, Cu, Zn, Cr, Ni) from deposited waste foundry sands. The overall, as well as heavy metals were extracted by different type of extractants: H2O, CH3COOH, HCl, EDTA, MgCl2 and NaCOOH. These extractants are most commonly used to study the mobility and bioavailability of metals in soil and waste. In the present study applicable standards and methodology described in the literature in analysis were used. The results allowed to evaluate the bioavailability of metals leached from those wastes.

An approach to managing cumulative effects to groundwater resources in the Alberta oil sands

International Nuclear Information System (INIS)

Fennell, J.; Forrest, Francine; Klebek, Margaret

2011-01-01

In the Athabasca region of Northern Alberta, oil sands activity has raised many concerns over how mining and extracting processes might affect groundwater quality and quantity. The groundwater management framework was developed by Alberta Environment to address these concerns by identifying and managing the potential environmental effects of oil sands activity on groundwater in a science-based manner. This paper develops the framework using risk identification and performance monitoring. The decision-making approach was conducted using decision support tools such as modeling, monitoring and management. Results showed the complexity and variability of groundwater conditions in the Athabasca region and pointed out that knowledge in this area is still developing. This paper presented how the groundwater management framework was developed and pointed out that it will have to be updated as new information arrives.

A study of the effects of LCD glass sand on the properties of concrete.

Science.gov (United States)

Wang, Her-Yung

2009-01-01

In order to study the recycling of discarded liquid crystal display (LCD) glass into concrete (LCDGC), a portion of the usual river sand was replaced by sand prepared from discarded LCD glass. Three different mix designs were regulated by the ACI method (fc(28)=21, 28, and 35MPa) with 0%, 20%, 40%, 60%, and 80% LCD glass sand replacements investigated; their engineering properties were determined. Test results revealed that, when compared to the design slump of 15cm, the 20% glass sand concrete for the three different mix designs kept good slump and slump flow. Furthermore, a slump loss ranging from 7 to 11cm was observed for specimens with 60% and 80% glass sand replacement for the design strengths of 28 and 35MPa. The compressive strengths of the concrete with glass sand replacement were higher than the design strengths. Moreover, the durability of the concrete with 20% glass sand replacement was better than that of the control group. Surface resistivity for specimens with different amounts of LCD glass sand replacement was also higher than that in the control group for mid to long curing ages. The sulfate attack in concrete with different amounts of glass sand replacement caused less weight loss than in the control group. Moderate chloride ion penetration was observed for glass sand concrete. Furthermore, the measured ultrasonic pulse velocities for LCD glass sand concrete specimens were higher than 4100m/s, which qualified these specimens as good concrete. OM and SEM indicate that the dense C-S-H gel hydrate was produced at the interface between the glass sand and cement paste. The test results indicate that the addition of 20% LCD glass sand to concrete satisfies the slump requirements and improves the strength and durability of concrete. This suggests that LCD glass sand can potentially be used as a recycled material in concrete applications.

Radon, radionuclides and the Cretaceous Folkestone Sands - gamma spectroscopy and geochemical analysis of silver sands and associated deposits in the SE of England.

Science.gov (United States)

Gillmore, Gavin; Al-Rafai, Yousef; Flowers, Alan

2017-04-01

Radon concentrations in a historic sand mine in Surrey, UK (Reigate Caves), have been measured by both real-time and time-averaged methods over a number of years. These mines are not identified as being in a 'Radon Affected Area' as defined by Public Health England, although concentrations show a summer level of 640 Bqm3 +-44 Bqm3. Average radon concentrations (September 2013 to January 2014) in Reigate caves were above the UK 200 Bqm3 domestic Action Level, above the UK domestic Target Level (of 100 Bqm3) but below the current workplace Action Level of 400 Bqm3. By way of a comparison radon has also been measured in nearby Dorking (South Street Caves). These enigmatic caves were not mined for sand for glass manufacture as Reigate Caves were and there is speculation on why the caves were created. Both are visited by tourists on a semi-regular basis. Dorking caves have a different morphology with radon concentrations in Autumn 2016 of up to 1940 +/- 230 Bqm3. The caves in Reigate are situated along Tunnel Road. These mines were also used as air raid shelters and wine stores. They consist of an East and West system and an older cave (Barons cave) which may have a medieval origin. As the Western Caves are now a shooting range our work has been carried out in the Eastern section at Reigate. Where Dorking is concerned the shops and houses in the town have extensive interconnected cellars and galleries cut into these sands. The caves probably date from the 17th century but were used quite extensively for wine storage in the 19th century due to their constant 140C air temperatures. Real-time measurements were taken with a Durridge Rad7 with time-averaged CR39 SSNTDs being placed throughout the cave systems to assess radon distribution and compare results with the real-time detector. Both caves contain marine shallow-water deposited locking (having tensile and compressive strength) silica sands of the Cretaceous Lower Greensand Group, Folkestone Formation, with little

Inland drift sand landscapes

NARCIS (Netherlands)

Fanta, J.; Siepel, H.

2010-01-01

Man has had a complex relationship with inland drift sands through the ages. For some centuries these landscapes were seen as a threat to society, especially agriculture and housing. At present we conserve these landscapes as important Natura 2000 priority habitats. In this book you may find these

Prediction of Liquefaction Potential of Dredge Fill Sand by DCP and Dynamic Probing

International Nuclear Information System (INIS)

Alam, Md. Jahangir; Azad, Abul Kalam; Rahman, Ziaur

2008-01-01

From many research it is proved that liquefaction potential of sand is function of mainly relative density and confining pressure. During routine site investigations, high-quality sampling and laboratory testing of sands are not feasible because of inevitable sample disturbance effects and budgetary constraints. On the other hand quality control of sand fill can be done by determining in situ density of sand in layer by layer which is expensive and time consuming. In this paper TRL DCP (Transportation Research Laboratory Dynamic Cone Penetration) and DPL (Dynamic Probing Light) are calibrated to predict the relative density of sand deposit. For this purpose sand of known relative density is prepared in a calibration chamber which is a mild steel cylinder with diameter 0.5 m and height 1.0 m. Relative density of sand is varied by controlling height of fall and diameter of hole of sand discharge bowl. After filling, every time DPL and DCP tests are performed and for every blow the penetration of cone is recorded. N10 is then calculated from penetration records. Thus a database is compiled where N10 and relative densities are known. A correlation is made between N 10 and relative density for two types of sand. A good correlation of N 10 and relative density is found

Nano sand filter with functionalized nanoparticles embedded in anodic aluminum oxide templates

OpenAIRE

Phuong, NguyenThi; Andisetiawan, Anugrah; Van Lam, Do; Kim, Jeong Hwan; Choi, Doo-Sun; Whang, Kyung-Hyun; Nham, Jeasun; Lee, Yun Jung; Yoo, Yeong-Eun; Yoon, Jae Sung

2016-01-01

Since the ancient Egyptians had used sand as filter media for water purification, its principle has been inherited through generations and it is still being used now in industries. The sand filter consists of sand literally, and the voids within the sand bed are the pores for filtration. Here we present a filtration principle using nanoparticles, so that the voids between the nanoparticles can be considered as effective pores in nanoscale dimension. Anodic aluminum oxide (AAO) membrane has be...

Processing Biological Gender and Number Information during Chinese Pronoun Resolution: ERP Evidence for Functional Differentiation

Science.gov (United States)

Xu, Xiaodong; Jiang, Xiaoming; Zhou, Xiaolin

2013-01-01

There have been a number of behavioral and neural studies on the processing of syntactic gender and number agreement information, marked by different morpho-syntactic features during sentence comprehension. By using the event-related potential (ERP) technique, the present study investigated whether the processing of semantic gender information and…

Markers inside wood : tree rings as archives of insect outbreaks, drift-sand dynamics, and spring flooding

NARCIS (Netherlands)

Copini, P.

2015-01-01

MARKERS INSIDE WOOD – TREE RINGS AS ARCHIVES OF INSECT OUTBREAKS, DRIFT-SAND DYNAMICS AND SPRING FLOODING

Trees are long-living organisms that record ecologically relevant information in their xylem that can be accessed by dendrochronology, the study of tree rings. Specific environmental

Bearing capacity of Skirt circular footing on sand

Directory of Open Access Journals (Sweden)

Amr Z. EL Wakil

2013-09-01

Full Text Available Skirts are used to improve the bearing capacity of shallow footings on sandy soil by constraining the soil beneath and containing the plastic flow of soil. They are used as an alternative to deep foundations in soils with low strength at the surface. As there has been available little work studying the performance of skirted foundation, we are performing eighteen laboratory experiments on circular steel footings of different diameters and different skirt lengths. The aim of these experiments is to shed some lights on the effects of skirts on the bearing capacity of shallow footings. The effects of skirt length and the relative density of sand on the ultimate load attained were investigated. From the accomplished laboratory tests, it was found that skirts improve appreciably the sustainability of shallow footings to applied load as they increase the ultimate load of shallow footings by some up to 6.25 times for the current study conditions and variables. The performance of skirted footing depends upon the relative density of sand and on the skirt length to footing diameter ratio. Skirts are more beneficial in case of footings on loose sand than in case of medium and dense sand.

Performance monitoring of electric shovels digging oil sands

Energy Technology Data Exchange (ETDEWEB)

Patnayak, S. [Alberta Univ., Edmonton, AB (Canada). Natural Resources Engineering Facility; Tannant, D.D. [Alberta Univ., Edmonton, AB (Canada). School of Mining and Petroleum Engineering; Parsons, I. [Syncrude Canada Ltd., Edmonton, AB (Canada). Edmonton Research Centre; Del Valle, V. [Syncrude Canada Ltd., Fort McMurray, AB (Canada)

2005-07-01

Some of the largest available mining equipment is used for oil sand mining operations. However, the performance of electric cable shovels varies with the diggability characteristics of the ground. In particular, oil sands diggability with cable shovels depends on structural geology, the depositional environment and geotechnical parameters. This paper described some of the key shovel performance indicators such as dig cycle time, digging energy and digging power. In winter, frost penetration can also affect oil sands diggability. The challenge of hard digging in oil sands is often addressed by blasting or ripping, which increases the cost of production and impedes productivity. The shovel performance is also influenced by other parameters such as operator skills, bucket and tooth design and shovel dipper trajectory. This paper demonstrated that hoist and crowd motor voltages and currents are useful in identifying the beginning and end of dig cycles. Performance indicators such as dig cycle time, hoist motor energy and power, and crowd motor energy and power were considered to assess material diggability. It was suggested that hoist power represents the ground diggability better than other performance indicators. 5 refs., 1 tab., 10 figs.

Isolation, identification, and pathological effects of beach sand bacterial extract on human skin keratinocytes in vitro

Directory of Open Access Journals (Sweden)

Fazli Subhan

2018-01-01

Full Text Available Background Beaches are recreational spots for people. However, beach sand contains harmful microbes that affect human health, and there are no established methods for either sampling and identifying beach-borne pathogens or managing the quality of beach sand. Method This study was conducted with the aim of improving human safety at beaches and augmenting the quality of the beach experience. Beach sand was used as a resource to isolate bacteria due to its distinctive features and the biodiversity of the beach sand biota. A selected bacterial isolate termed FSRS was identified as Pseudomonas stutzeri using 16S rRNA sequencing and phylogenetic analysis, and the sequence was deposited in the NCBI GenBank database under the accession number MF599548. The isolated P. stutzeri bacterium was cultured in Luria–Bertani growth medium, and a crude extract was prepared using ethyl acetate to examine the potential pathogenic effect of P. stutzeri on human skin. A human skin keratinocyte cell line (HaCaT was used to assess cell adhesion, cell viability, and cell proliferation using a morphological analysis and a WST-1 assay. Result The crude P. stutzeri extract inhibited cell adhesion and decreased cell viability in HaCaT cells. We concluded that the crude extract of P. stutzeri FSRS had a strong pathological effect on human skin cells. Discussion Beach visitors frequently get skin infections, but the exact cause of the infections is yet to be determined. The beach sand bacterium P. stutzeri may, therefore, be responsible for some of the dermatological problems experienced by people visiting the beach.

Geotechnical properties of oil-contaminated Kuwaiti sand

Energy Technology Data Exchange (ETDEWEB)

Al-Sanad, H.A.; Eid, W.K.; Ismael, N.F. [Kuwait Univ., Safat (Kuwait). Dept. of Civil Engineering

1995-05-01

Large quantities of oil-contaminated sands resulted from exploded oil wells, burning oil fires, the destruction of oil storage tanks, and the formation of oil lakes in Kuwait at the end of the Gulf War. An extensive laboratory testing program was carried out to determine the geotechnical characteristics of this material. Testing included basic properties, compaction and permeability tests, and triaxial and consolidation tests on clean and contaminated sand at the same relative density. Contaminated specimens were prepared by mixing the sand with oil in the amount of 6% by weight or less to match field conditions. The influence of the type of oil, and relative density was also investigated by direct shear tests. The results indicated a small reduction in strength and permeability and an increase in compressibility due to contamination. The preferred method of disposal of this material is to use it as a stabilizing material for other projects such as road construction.

Insight conference reports : Western Canada oil sands

International Nuclear Information System (INIS)

2005-01-01

This conference presented issues of concern to the Canadian oil sands industry. Focal points included supply and the potential for market growth as well as opportunities and challenges faced by the industry in the current market. Various projects were discussed, including the Northern Lights and Fort Hill projects. Reserves and resource booking procedures were examined, as well as issues concerning the streamlining of regulatory barriers and various approaches to the Kyoto Protocol and greenhouse gas (GHG) emissions. Oil sands portfolios were reviewed as well as issues concerning the recovery of titanium and zircon, the economics of Steam Assisted Gravity Drainage (SAGD) options and innovations in technology and sub-surface risk assessment for in-situ projects. Transportation initiatives were examined as well as pipeline issues and storage infrastructure development. Issues concerning financing as well as the economic environment of the oil sands industry were also discussed. The conference featured 20 presentations, of which 5 have been catalogued separately for inclusion in this database. tabs, figs

Geotechnical properties of oil-contaminated Kuwaiti sand

International Nuclear Information System (INIS)

Al-Sanad, H.A.; Eid, W.K.; Ismael, N.F.

1995-01-01

Large quantities of oil-contaminated sands resulted from exploded oil wells, burning oil fires, the destruction of oil storage tanks, and the formation of oil lakes in Kuwait at the end of the Gulf War. An extensive laboratory testing program was carried out to determine the geotechnical characteristics of this material. Testing included basic properties, compaction and permeability tests, and triaxial and consolidation tests on clean and contaminated sand at the same relative density. Contaminated specimens were prepared by mixing the sand with oil in the amount of 6% by weight or less to match field conditions. The influence of the type of oil, and relative density was also investigated by direct shear tests. The results indicated a small reduction in strength and permeability and an increase in compressibility due to contamination. The preferred method of disposal of this material is to use it as a stabilizing material for other projects such as road construction

Development tendencies of moulding and core sands

Directory of Open Access Journals (Sweden)

Stanislaw M. Dobosz1

2011-11-01

Full Text Available Further development of the technology for making moulding and core sands will be strictly limited by tough requirements due to protection of the natural environment. These tendencies are becoming more and more tense, so that we will reach a point when even processes, that from technological point of view fulfill high requirements of the foundry industry, must be replaced by more ecologically-friendly solutions. Hence, technologies using synthetic resins as binding materials will be limited. This paper presents some predictable development tendencies of moulding and core sands. The increasing role of inorganic substances will be noticed, including silicate binders with significantly improved properties, such as improved knock-out property or higher reclamation strength. Other interesting solutions might also be moulding sands bonded by geo-polymers and phosphate binders or salts and also binders based on degradable biopolymers. These tendencies and the usefulness of these binders are put forward in this paper.

Recycled sand in lime-based mortars.

Science.gov (United States)

Stefanidou, M; Anastasiou, E; Georgiadis Filikas, K

2014-12-01

The increasing awareness of the society about safe guarding heritage buildings and at the same time protecting the environment promotes strategies of combining principles of restoration with environmentally friendly materials and techniques. Along these lines, an experimental program was carried out in order to investigate the possibility of producing repair, lime-based mortars used in historic buildings incorporating secondary materials. The alternative material tested was recycled fine aggregates originating from mixed construction and demolition waste. Extensive tests on the raw materials have been performed and mortar mixtures were produced using different binding systems with natural, standard and recycled sand in order to compare their mechanical, physical and microstructure properties. The study reveals the improved behavior of lime mortars, even at early ages, due to the reaction of lime with the Al and Si constituents of the fine recycled sand. The role of the recycled sand was more beneficial in lime mortars rather than the lime-pozzolan or lime-pozzolan-cement mortars as a decrease in their performance was recorded in the latter cases due to the mortars' structure. Copyright © 2014 Elsevier Ltd. All rights reserved.

The Suitability Of Local Quartz Sand In The Production Of Bath Crucibles.

Directory of Open Access Journals (Sweden)

C. O. Okpanachi

2017-03-01

Full Text Available The suitability of local quartz sand in the production of bath crucibles is a study that was carried out in order to impart overall strength on bath crucibles hence reduce breakages during fettling. Therefore this research constitutes a study to enhance the efficiency of production of bath crucibles by addition of quartz sand in slip preparation. The steps taken in the beneficiation of quartz sand for the production of bath crucibles are comminution which entails crushing and milling classification washing liquid dispersion sizing and reduction of iron content by magnetic separation. The slip contains materials like plastic clay feldspar kaolin talc sodium silicate water quartz sand etc. These were all milled in the ball mill for slip production casting and fettling glazing and sintering to get final bath crucibles as the end products. Quartz sand is used in a variety of products essentially as raw material for the foundry casting and glass industries and also in chemicals water filtration and ceramics the heat resistance nature of quartz sand makes it an excellent refractory substance for these industrial processes. Slip can be prepared for production of bath crucibles without the inclusion of quartz sand however the addition of quartz sand is needed to improve the mechanical performance of the slip in the production of bath crucibles.

Traceability of Height Measurements on Green Sand Molds using Optical 3D Scanning

DEFF Research Database (Denmark)

Mohaghegh, Kamran; Yazdanbakhsh, S.A.; Tiedje, N. S.

2016-01-01

Establishing a reliable measurement procedure for dimensional measurements on green sand molds is a prerequisite for analysis of geometric deviations in mass production of quality castings. Surface of the green sand mold is not suitable for measurements using a tactile coordinate measuring machine....... This paper presents a metrological approach for height measurement on green sand molds using an optical 3D scanner with fringe projection. A new sand sample was developed with a hard binder to withstand the contact force of a touch probe, while keeping optical cooperativeness similar to green sand...

Sand fly-Leishmania interactions: long relationships are not necessarily easy

OpenAIRE

Ramalho-Ortigao, Marcelo; Saraiva, Elvira M.; Traub-Csekö, Yara M.

2010-01-01

Sand fly and Leishmania are one of the best studied vector-parasite models. Much is known about the development of these parasites within the sand fly, and how transmission to a suitable vertebrate host takes place. Various molecules secreted by the vector assist the establishment of the infection in a vertebrate, and changes to the vector are promoted by the parasites in order to facilitate or enhance transmission. Despite a generally accepted view that sand flies and Leishmania are also one...

Frac Sand Mines Are Preferentially Sited in Unzoned Rural Areas.

Directory of Open Access Journals (Sweden)

Christina Locke

Full Text Available Shifting markets can cause unexpected, stochastic changes in rural landscapes that may take local communities by surprise. Preferential siting of new industrial facilities in poor areas or in areas with few regulatory restrictions can have implications for environmental sustainability, human health, and social justice. This study focuses on frac sand mining-the mining of high-quality silica sand used in hydraulic fracturing processes for gas and oil extraction. Frac sand mining gained prominence in the 2000s in the upper midwestern United States where nonmetallic mining is regulated primarily by local zoning. I asked whether frac sand mines were more commonly sited in rural townships without formal zoning regulations or planning processes than in those that undertook zoning and planning before the frac sand boom. I also asked if mine prevalence was correlated with socioeconomic differences across townships. After creating a probability surface to map areas most suitable for frac sand mine occurrence, I developed neutral landscape models from which to compare actual mine distributions in zoned and unzoned areas at three different spatial extents. Mines were significantly clustered in unzoned jurisdictions at the statewide level and in 7 of the 8 counties with at least three frac sand mines and some unzoned land. Subsequent regression analyses showed mine prevalence to be uncorrelated with land value, tax rate, or per capita income, but correlated with remoteness and zoning. The predicted mine count in unzoned townships was over two times higher than that in zoned townships. However, the county with the most mines by far was under a county zoning ordinance, perhaps indicating industry preferences for locations with clear, homogenous rules over patchwork regulation. Rural communities can use the case of frac sand mining as motivation to discuss and plan for sudden land-use predicaments, rather than wait to grapple with unfamiliar legal processes

A novel bench-scale column assay to investigate site-specific nitrification biokinetics in biological rapid sand filters

DEFF Research Database (Denmark)

Tatari, Karolina; Smets, Barth F.; Albrechtsen, Hans-Jørgen

2013-01-01

A bench-scale assay was developed to obtain site-specific nitrification biokinetic information from biological rapid sand filters employed in groundwater treatment. The experimental set-up uses granular material subsampled from a full-scale filter, packed in a column, and operated with controlled...

Western tight gas sands advanced logging workshop proceedings

Energy Technology Data Exchange (ETDEWEB)

Jennings, J B; Carroll, Jr, H B [eds.

1982-04-01

An advanced logging research program is one major aspect of the Western Tight Sands Program. Purpose of this workshop is to help BETC define critical logging needs for tight gas sands and to allow free interchange of ideas on all aspects of the current logging research program. Sixteen papers and abstracts are included together with discussions. Separate abstracts have been prepared for the 12 papers. (DLC)

On the Size Distribution of Sand

DEFF Research Database (Denmark)

Sørensen, Michael

2016-01-01

A model is presented of the development of the size distribution of sand while it is transported from a source to a deposit. The model provides a possible explanation of the log-hyperbolic shape that is frequently found in unimodal grain size distributions in natural sand deposits, as pointed out......-distribution, by taking into account that individual grains do not have the same travel time from the source to the deposit. The travel time is assumed to be random so that the wear on the individual grains vary randomly. The model provides an interpretation of the parameters of the NIG-distribution, and relates the mean...

Influence of Geometric Parameters of the Hydrocyclone and Sand Concentration on the Water/Sand/Heavy-Oil Separation Process: Modeling and Simulation

Directory of Open Access Journals (Sweden)

F Farias

2016-09-01

Full Text Available In the oil exploitation, produced fluids are composed of oil, gas, water and sand (depending on the reservoir location. The presence of sand in flow oil leads to several industrial problems for example: erosion and accumulation in valves and pipeline. Thus, it is necessary to stop production for manual cleaning of equipments and pipes. These facts have attracted attention of academic and industrial areas, enabling the appearing of new technologies or improvement of the water/oil/sand separation process. One equipment that has been used to promote phase separation is the hydrocyclone due to high performance of separation and required low cost to installation and maintenance. In this sense, the purpose of this work is to study numerically the effect of geometric parameters (vortex finder diameter of the hydrocyclone and sand concentration on the inlet fluid separation process. A numerical solution of the governing equations was obtained by the ANSYS CFX-11 commercial code. Results of the streamlines, pressure drop and separation efficiency on the hydrocyclone are presented and analyzed. It was observed that the particles concentration and geometry affect the separation efficiency of the hydrocyclone.

Crushed and River-Origin Sands Used as Aggregates in Repair Mortars

Directory of Open Access Journals (Sweden)

Maria Stefanidou

2016-04-01

Full Text Available The systematic analysis of mortars from monuments or historic buildings and the simultaneous study of the construction environment show that it was common practice to use naturally occurring sand from local rivers or streams for the production of the mortars. There are cases though, mainly on islands, where sands of natural origin were limited, and marine or crushed sands were used possibly after elaboration. In all cases the particle size analysis of old mortar confirms the presence of even distribution of the granules. As regards the design of the repair mortars, there are criteria that should be taken into consideration in order to produce materials with compatible properties. The main properties concerning sands are the grain distribution and maximum size, the color, the content of fines, and soluble salts. The objective of this research is the study of the physical characteristics of the sands such as the sand equivalent, the gradation, the apparent density, the morphology of the grains, their mineralogical composition and the influence of these properties on the behavior of lime mortars, notably the mechanical and physical properties acquired.

ANN modelling for the determination of moulding sand matrix grain size

Directory of Open Access Journals (Sweden)

J. Jakubski

2011-10-01

Full Text Available One of the modern methods of the production optimisation are artificial neural networks. Neural networks are gaining broader and broader application in the foundry industry, among others for controlling melting processes in cupolas and in arc furnaces, for designing castings and supply systems, for controlling moulding sand processing, for predicting properties of cast alloys or selecting parameters of pressure castings. An attempt to apply neural networks for controlling the quality of bentonite moulding sands is presented in this paper. This is the assessment method of sands suitability by means of detecting correlations between their individual parameters. The presented investigations were obtained by using the Statistica 9.0 program. The aim of the investigations was to select the neural network suitable for prediction the moulding sand matrix grain size on the basis of the determined sand properties such as: permeability, compactibility, and compressive strength.