Initial geochemical characteristics of fluid fine tailings in an oil sands end pit lake

Energy Technology Data Exchange (ETDEWEB)

Dompierre, Kathryn A. [Department of Civil and Geological Engineering, University of Saskatchewan, Saskatoon, Saskatchewan, Canada S7N 5A9 (Canada); Lindsay, Matthew B.J., E-mail: matt.lindsay@usask.ca [Department of Geological Sciences, University of Saskatchewan, Saskatoon, Saskatchewan S7N 5E2 (Canada); Cruz-Hernández, Pablo [Department of Geology, University of Huelva, Campus ‘El Carmen’, E-21071 Huelva (Spain); Halferdahl, Geoffrey M. [Environmental Research and Development, Syncrude Canada Limited, Edmonton, Alberta T6N 1H4 (Canada)

2016-06-15

Geochemical characteristics of fluid fine tailings (FFT) were examined in Base Mine Lake (BML), which is the first full-scale demonstration oil sands end pit lake (EPL) in northern Alberta, Canada. Approximately 186 Mm{sup 3} of FFT was deposited between 1994 and 2012, before BML was established on December 31, 2012. Bulk FFT samples (n = 588) were collected in July and August 2013 at various depths at 15 sampling sites. Temperature, solid content, electrical conductivity (EC), pH, Eh and alkalinity were measured for all samples. Detailed geochemical analyses were performed on a subset of samples (n = 284). Pore-water pH decreased with depth by approximately 0.5 within the upper 10 m of the FFT. Major pore-water constituents included Na (880 ± 96 mg L{sup −1}) and Cl (560 ± 95 mg L{sup −1}); Ca (19 ± 4.1 mg L{sup −1}), Mg (11 ± 2.0 mg L{sup −1}), K (16 ± 2.3 mg L{sup −1}) and NH{sub 3} (9.9 ± 4.7 mg L{sup −1}) were consistently observed. Iron and Mn concentrations were low within FFT pore water, whereas SO{sub 4} concentrations decreased sharply across the FFT–water interface. Geochemical modeling indicated that FeS{sub (s)} precipitation was favoured under SO{sub 4}-reducing conditions. Pore water was also under-saturated with respect to gypsum [CaSO{sub 4}·2H{sub 2}O], and near saturation with respect to calcite [CaCO{sub 3}], dolomite [CaMg(CO{sub 3}){sub 2}] and siderite [FeCO{sub 3}]. X-ray diffraction (XRD) suggested that carbonate-mineral dissolution largely depleted calcite and dolomite. X-ray absorption near edge structure (XANES) spectroscopy revealed the presence of FeS{sub (s)}, pyrite [FeS{sub 2}], and siderite. Carbonate-mineral dissolution and secondary mineral precipitation have likely contributed to FFT dewatering and settlement. However, the long-term importance of these processes within EPLs remains unknown. These results provide a reference for assessing the long-term geochemical evolution of oil sands EPLs, and offer

Short-term impact of deep sand extraction and ecosystem-based landscaping on macrozoobenthos and sediment characteristics.

Science.gov (United States)

de Jong, Maarten F; Baptist, Martin J; Lindeboom, Han J; Hoekstra, Piet

2015-08-15

We studied short-term changes in macrozoobenthos in a 20m deep borrow pit. A boxcorer was used to sample macrobenthic infauna and a bottom sledge was used to sample macrobenthic epifauna. Sediment characteristics were determined from the boxcore samples, bed shear stress and near-bed salinity were estimated with a hydrodynamic model. Two years after the cessation of sand extraction, macrozoobenthic biomass increased fivefold in the deepest areas. Species composition changed significantly and white furrow shell (Abra alba) became abundant. Several sediment characteristics also changed significantly in the deepest parts. Macrozoobenthic species composition and biomass significantly correlated with time after cessation of sand extraction, sediment and hydrographical characteristics. Ecosystem-based landscaped sand bars were found to be effective in influencing sediment characteristics and macrozoobenthic assemblage. Significant changes in epifauna occurred in deepest parts in 2012 which coincided with the highest sedimentation rate. We recommend continuing monitoring to investigate medium and long-term impacts. Copyright © 2015 Elsevier Ltd. All rights reserved.

Sediment Transport and Infilling of a Borrow Pit on an Energetic Sandy Ebb Tidal Delta Offshore of Hilton Head Island, South Carolina

Science.gov (United States)

Wren, A.; Xu, K.; Ma, Y.; Sanger, D.; Van Dolah, R.

2014-12-01

Bottom-mounted instrumentation was deployed at two sites on an ebb tidal delta to measure hydrodynamics, sediment transport, and seabed elevation. One site ('borrow site') was 2 km offshore and used as a dredging site for beach nourishment of nearby Hilton Head Island in South Carolina, and the other site ('reference site') was 10 km offshore and not directly impacted by the dredging. In-situ time-series data were collected during two periods after the dredging: March 15 - June 12, 2012('spring') and August 18 - November 18, 2012 ('fall'). At the reference site directional wave spectra and upper water column current velocities were measured, as well as high-resolution current velocity profiles and suspended sediment concentration profiles in the Bottom Boundary Layer (BBL). Seabed elevation and small-scale seabed changes were also measured. At the borrow site seabed elevation and near-bed wave and current velocities were collected using an Acoustic Doppler Velocimeter. Throughout both deployments bottom wave orbital velocities ranged from 0 - 110 m/s at the reference site. Wave orbital velocities were much lower at the borrow site ranging from 10-20 cm/s, as wave energy was dissipated on the extensive and rough sand banks before reaching the borrow site. Suspended sediment concentrations increased throughout the BBL when orbital velocities increased to approximately 20 cm/s. Sediment grain size and critical shear stresses were similar at both sites, therefore, re-suspension due to waves was less frequent at the borrow site. However, sediment concentrations were highly correlated with the tidal cycle at both sites. Semidiurnal tidal currents were similar at the two sites, typically ranging from 0 - 50 cm/s in the BBL. Maximum currents exceeded the critical shear stress and measured suspended sediment concentrations increased during the first hours of the tidal cycle when the tide switched to flood tide. Results indicate waves contributed more to sediment mobility at

Chemical mass transport between fluid fine tailings and the overlying water cover of an oil sands end pit lake

Science.gov (United States)

Dompierre, Kathryn A.; Barbour, S. Lee; North, Rebecca L.; Carey, Sean K.; Lindsay, Matthew B. J.

2017-06-01

Fluid fine tailings (FFT) are a principal by-product of the bitumen extraction process at oil sands mines. Base Mine Lake (BML)—the first full-scale demonstration oil sands end pit lake (EPL)—contains approximately 1.9 × 108 m3 of FFT stored under a water cover within a decommissioned mine pit. Chemical mass transfer from the FFT to the water cover can occur via two key processes: (1) advection-dispersion driven by tailings settlement; and (2) FFT disturbance due to fluid movement in the water cover. Dissolved chloride (Cl) was used to evaluate the water cover mass balance and to track mass transport within the underlying FFT based on field sampling and numerical modeling. Results indicated that FFT was the dominant Cl source to the water cover and that the FFT is exhibiting a transient advection-dispersion mass transport regime with intermittent disturbance near the FFT-water interface. The advective pore water flux was estimated by the mass balance to be 0.002 m3 m-2 d-1, which represents 0.73 m of FFT settlement per year. However, the FFT pore water Cl concentrations and corresponding mass transport simulations indicated that advection rates and disturbance depths vary between sample locations. The disturbance depth was estimated to vary with location between 0.75 and 0.95 m. This investigation provides valuable insight for assessing the geochemical evolution of the water cover and performance of EPLs as an oil sands reclamation strategy.

The use of stable isotopes to trace oil sands constituents

International Nuclear Information System (INIS)

Farwell, A.J.; Nero, V.; Dixon, D.G.

2002-01-01

A study was conducted to determine the biological effects of oil sands mining operations on aquatic ecosystems. The study focused on the Athabasca oil sand deposit, the largest of 4 deposits in northern Alberta. In particular, the study examined the cycling of oil sand constituents in Benthic invertebrates collected from test pits at Syncrude Canada Ltd.. The invertebrates were similar in size, but different in the quantity of process-affected water or mature fine tailings containing residual bitumen. Dragonflies and damselflies in particular, showed trends of depletion for the carbon 13 isotope and enrichment in nitrogen 15 isotope in pits where levels of process affected water was high. The depletion of carbon 13 isotope suggests that oil sand constituents assimilate into the benthic food chain. The greatest carbon 13 depletion, which was approximately 27 per cent, was found to be in test pits with high turbidity. This implies that oil sands constituents degrade microbially instead of by photosynthetic production. All benthic invertebrate group demonstrated an incremental enrichment in nitrogen 15 isotope from the control pit to the pit with greatest levels of mature fine tailings

The chemical and biological evolution of mature fine tailings in oil sands end-pit lakes

International Nuclear Information System (INIS)

Chen, M.; Weisener, C.; Ciborowski, J.

2010-01-01

This presentation described an innovative bench-scale technique to characterize oil sand tailings and their impact on sediment oxygen demand (SOD) for future end-pit lake model behaviour. SOD is a dominant contributor to oxygen depletion in wetlands. The function and sustainability of a wetland ecosystem depends on the biochemical processes occurring at the sediment-water interface. The biochemical reactions associated with natural sediment can change with the addition of oil sands processed material (OSPM), which can affect SOD and ecosystem viability. It is important to establishing the biotic and abiotic controls of SOD. In order to evaluate the effectiveness of current wetland reclamation designs, it is important to establish the biotic and abiotic controls of SOD. The REDOX chemistry of fresh tailings sediment (MFT) was measured in this laboratory microcosm to determine the chemical and biological influences, and to study the role of developing microbial communities as new mature fine tailings (MFT) age. The study evaluated the changes in the main chemical, physical and biological populations of the MFT in both aerobic and anaerobic microcosms. A combination of microelectrode arrays and DNA profiling at the tailings water interface was used in the study.

Seismic tests of a pile-supported structure in liquefiable sand using large-scale blast excitation

International Nuclear Information System (INIS)

Kamijo, Naotaka; Saito, Hideaki; Kusama, Kazuhiro; Kontani, Osamu; Nigbor, Robert

2004-01-01

Extensive, large-amplitude vibration tests of a pile-supported structure in a liquefiable sand deposit have been performed at a large-scale mining site. Ground motions from large-scale blasting operations were used as excitation forces for vibration tests. A simple pile-supported structure was constructed in an excavated 3 m-deep pit. The test pit was backfilled with 100% water-saturated clean uniform sand. Accelerations were measured on the pile-supported structure, in the sand in the test pit, and in the adjacent free field. Excess pore water pressures in the test pit and strains of one pile were also measured. Vibration tests were performed with six different levels of input motions. The maximum horizontal acceleration recorded at the adjacent ground surface varied from 20 Gals to 1353 Gals. These alternations of acceleration provided different degrees of liquefaction in the test pit. Sand boiling phenomena were observed in the test pit with larger input motions. This paper outlines vibration tests and investigates the test results

Methane Fluxes and Consumption in an Oil Sands Tailings End Pit Lake

Science.gov (United States)

Slater, G. F.; Goad, C.; Arriaga, D.; Risacher, F.; Morris, P.; Lindsay, M. B.; Mumford, K. G.; Warren, L. A.

2017-12-01

End pit lakes are engineered freshwater lakes designed to reclaim land impacted by surface mining activities via establishment of a functioning ecosystem where biogeochemical cycling mitigates release of hazardous components either by stabilization or biodegradation. End pit lakes provide unique opportunities to gain insight into microbial nutrient cycling under extreme levels of impact that can be applicable to a range of levels of anthropogenic impacts and issues. This study focuses on microbial CH4 cycling in the underlying fluid fine tailings (FFT) and surface waters of Base Mine Lake (BML), the first full demonstration of end pit lake reclamation in the Athabasca Oil Sands Region (AOSR) of northern Alberta, Canada. Over two field seasons (2015 and 2016) BML was thermally stratified, turning over in spring and fall. Oxygen concentrations in the epilimnion (70 to 80 % saturation) decreased steeply through the metalimnion to 3% saturation in the hypolimnion. Conversely, CH4 concentrations were highest in the hypolimnion of BML (25 to 140 µM) with the highest values being observed at the FFT/Water interface. Concentrations decreased to 1-2 µM at the metalimnion and further decreased to < 0.5 µM in the epilimnion. CH4 δ13C in FFT porewater indicated production via fermentative pathways. FFT settlement and dewatering of 0.73 to 1.0 m/yr results in advection of an estimated 1x107 to 2x107 moles/yr CH4 into the surface water, circa an order of magnitude greater than the 3x106 moles/year estimated for molecular diffusion. Calculated fluxes of dissolved CH4 from the FFT into the hypolimnion were 4 orders of magnitude higher than those from the hypolimnion to the metalimnion, indicating a significant sink for CH4 within the hypolimnion limiting upward dissolved CH4 transport. Dissolution of CH4 from bubbles released from the FFT may be contributing to the observed epilimnion concentrations. CH4 δ13C in the hypolimnion showed only minimal enrichment with decreasing

Radiation protection in the sand pit

International Nuclear Information System (INIS)

Hewson, Greg

1997-01-01

Radiation protection in the Western Australian minerals sands industry has attracted considerable controversy over the last 20 years: firstly, in relation to environmental and public health issues associated with the indiscriminate disposal of radioactive tailings as landfill in the mid to late 1970s and, secondly, in relation to occupational health issues associated with excessive radiation exposures to some workers at some plants in the mid to late 1980s. The industry also attracts attention through its proximity to coastal regions and population centres and consequent land use conflicts. Owing to intense political and societal scrutiny, and the emotional responses evoked by radiation, the industry's survival depends on a continuing high level of environmental and safety performance. This article summarises the successes and failures of the mineral sands industry in managing radiation protection and highlights some future issues and challenges for the industry. (Author)

Construction of the KUT test pits

International Nuclear Information System (INIS)

Knapp, K.E.; Bush, W.E.

1976-09-01

Models are required to calibrate spectral logging systems to differentiate between U, Th, and K (''KUT''), in order to determine the grade of low-grade U deposits. The models were constructed by excavating three pits, emplacing three form tanks (11 ft long, 4 ft dia culvert) with 4-in. dia central holes, and pouring the following zones: 3-ft concrete lower barren zone, a 5-ft ore zone, and a final 3-ft upper barren zone. The U ore zone comprised 0.33 percent U 3 O 8 Climax ore, sand, cement, and water; the Th ore zone comprised monazite sands, plaster sand, cement, and water; and the K ore zone comprised feldspar, cement, and water. Form pipes were used to form the central holes. Analyses were made of samples taken from the zones

105-KW Sandfilter Backwash Pit sludge volume calculation

International Nuclear Information System (INIS)

Dodd, E.N. Jr.

1995-01-01

The volume of sludge contained in the 100-KW Sandfilter Backwash Pit (SFBWP) was calculated from depth measurements of the sludge, pit dimension measurements and analysis of video tape recordings taken by an underwater camera. The term sludge as used in this report is any combination of sand, sediment, or corrosion products visible in the SFBWP area. This work was performed to determine baseline volume for use in determination of quantities of uranium and plutonium deposited in the pit from sandfilter backwashes. The SFBWP has three areas where sludge is deposited: (1) the main pit floor, (2) the transfer channel floor, and (3) the surfaces and structures in the SFBWP. The depths of sludge and the uniformity of deposition varies significantly between these three areas. As a result, each of the areas was evaluated separately. The total volume of sludge determined was 3.75 M 3 (132.2 ft 3 )

Modeling and management of pit lake water chemistry 1: Theory

International Nuclear Information System (INIS)

Castendyk, D.N.; Eary, L.E.; Balistrieri, L.S.

2015-01-01

Highlights: • Review of pit lake literature in the context of pit lake predictions. • Review of approaches used to predict pit wall-rock runoff and leachate. • Review of approaches used to generate a pit lake water balance. • Review of approaches used to generate a hydrodynamic prediction. • Review of approaches used to generate a geochemical prediction of a future pit lake. - Abstract: Pit lakes are permanent hydrologic/landscape features that can result from open pit mining for metals, coal, uranium, diamonds, oil sands, and aggregates. Risks associated with pit lakes include local and regional impacts to water quality and related impacts to aquatic and terrestrial ecosystems. Stakeholders rely on predictive models of water chemistry to prepare for and manage these risks. This paper is the first of a two part series on the modeling and management of pit lakes. Herein, we review approaches that have been used to quantify wall-rock runoff geochemistry, wall-rock leachate geochemistry, pit lake water balance, pit lake limnology (i.e. extent of vertical mixing), and pit lake water quality, and conclude with guidance on the application of models within the mine life cycle. The purpose of this paper is to better prepare stakeholders, including future modelers, mine managers, consultants, permitting agencies, land management agencies, regulators, research scientists, academics, and other interested parties, for the challenges of predicting and managing future pit lakes in un-mined areas

A numerical study of under-deposit pitting corrosion in sour petroleum pipelines

Energy Technology Data Exchange (ETDEWEB)

Zhu, Z.; Sand, K.W.; Teevens, P.J. [Broadsword Corrosion Engineering Ltd., Calgary, AB (Canada)

2010-07-01

Insufficient fluid velocity in petroleum pipelines can lead to the deposit of sand, corrosion products, and non-corrosion products on the pipe's metal surface, which in turn can lead to pitting corrosion. There is currently no reliable means of detecting and preventing the pitting process. This paper presented a computerized simulation tool that used the finite element method to model mass transfer-governed internal pitting corrosion under solids deposition in sour petroleum pipelines. The computational domain consisted of a hemispherical pit and a thin stagnant solution film under a surface deposit. The moving mesh method was used to track pitting growth. A Poisson equation was used to determine aqueous path migration of ions. Pitting corrosion rates were estimated using the Nernst-Planck equation. The model was used to predict the effects of different operating parameters on pitting corrosion rates. The model can be used to develop pigging and in-line-inspection (ILI) procedures. 35 refs., 2 tabs., 16 figs.

34 CFR 682.604 - Processing the borrower's loan proceeds and counseling borrowers.

Science.gov (United States)

2010-07-01

... 34 Education 3 2010-07-01 2010-07-01 false Processing the borrower's loan proceeds and counseling...'s loan proceeds and counseling borrowers. (a) General. (1) This section establishes rules governing a school's processing of a borrower's Stafford or PLUS loan proceeds, and for counseling borrowers...

Natural radionuclide content and radiological hazard associated with usage of quartzite sand samples from Ovacik-Silifke-Mersin open pit as building material in Turkey.

Science.gov (United States)

Turhan, S; Aykamis, A S; Kiliç, A M

2009-09-01

Activity concentrations of (238)U, (232)Th, (226)Ra and (40)K in quartzite sand samples collected from the Ovacik-Silifke-Mersin open pit located in the East Mediterranean region of Turkey were determined by using a gamma-ray spectrometry technique. The mean activity concentrations of the (238)U, (232)Th, (226)Ra and (40)K in quartzite sand samples were found as 81.7 +/- 22.9 Bq kg(-1), 6.3 +/- 2.8 Bq kg(-1), 77.5 +/- 24.3 Bq kg(-1)and 140.0 +/- 124.1 Bq kg(-1), respectively. The gamma index (I(gamma)), the internal exposure index (I(alpha)), the indoor absorbed dose rate (D(in)) and the corresponding annual effective dose (H(in)) were evaluated for the public exposure to radiological hazard arising due to the use of quartzite sand samples as building material. The values of I(gamma), I(alpha), D(in) and H(in) ranged from 0.20 to 0.75, with a mean of 0.34 +/- 0.11, 0.23 to 0.77 with a mean of 0.39 +/- 0.12, 58.27 to 201.51 nGy h(-1) with a mean of 93.33 +/- 27.63 nGy h(-1) and 0.29 to 0.99 mSv with a mean of 0.46 +/- 0.14 mSv, respectively.

Restoration of Prime Farmland Disturbed by Mineral Sand Mining in the Upper Coastal Plain of Virginia

OpenAIRE

Schroeder, Philip D.

1996-01-01

Economic deposits of heavy mineral sand were identified in the late 1980's under prime farmland along the Upper Coastal Plain of Virginia. Mining in Virginia will commence in 1997 on the Old Hickory Deposit in Dinwiddie/Sussex Counties. Experiments were established on two mine pits representing two likely pit closure scenarios; regrading the surface with unprocessed subsoil (Pit 1) or filling to the surface with processed material (Pit 3). To evaluate topsoil replacement vs. organic amendment...

Short-term impact of deep sand extraction and ecosystem-based landscaping on macrozoobenthos and sediment characteristics

NARCIS (Netherlands)

de Jong, Maarten F.; Baptist, Martin J.; Lindeboom, Han J.; Hoekstra, Piet

2015-01-01

We studied short-term changes in macrozoobenthos in a 20. m deep borrow pit. A boxcorer was used to sample macrobenthic infauna and a bottom sledge was used to sample macrobenthic epifauna. Sediment characteristics were determined from the boxcore samples, bed shear stress and near-bed salinity were

Modelling assessment of End Pit Lakes meromictic potential

International Nuclear Information System (INIS)

2006-11-01

The use of End Pit Lakes have been proposed as a remediation solution for oil sands reclamation and operational waters. This report modelled the main factors controlling the occurrence of stratification in Pit Lakes in order to establish design and management guidelines for the Cumulative Environmental Management Association's End Pit Lake Sub-group. The study focused on End Pit Lake size, depth, starting lake salinity concentrations, inflow rates and inflow salinity flux, and investigated their influence on density gradients. One-dimensional modelling and limited 2-D modelling simulations were conducted to examine meromictic potential for a large range of End Pit Lake configurations and conditions. Modelling results showed that fall is the governing season for determining meromixis. The expelling of salt from saline water upon ice formation and its effect on stratification potential and the effect of fresh water loading on stratification potential during spring melt events were not observed to be dominant factors governing meromictic potential for the scenarios examined in the study. Results suggested that shallow End Pit Lakes showed a high turn-over rate with seasonal heating and cooling cycles. Moderately deep End Pit Lakes demonstrated a meromictic potential that was inversely proportional to lake size and require higher starting salinities. With a 2 or 10 million m 3 /yr inflow rate and a 5 parts per thousand starting salinity, a 50 m deep End Pit Lake achieved meromixis at all 3 size ranges considered in the study. Results also showed that the rate of influent salinity decrease was the least important of the parameters influencing meromixis. It was observed that meromixis was a temporary condition in all of the End Pit Lake scenarios envisioned due to the lack of a constant, positive salt replenishment over the long term. It was concluded that further 3-D modelling is required to represent littoral areas as well as to account for extreme winter conditions. A

Repair procedure used in removing corroded pits in the distillation towers of the Getulio Vargas Refinery Unit 2100

Energy Technology Data Exchange (ETDEWEB)

Lordelos, H.M.; Santin, J.L.

1977-07-01

A description is given of the corrosion pits on ASTM A240, Type 405 steel cladded to carbon steel plates used in Petroleo Brasileiro S.A.'s Getulio Vargas Refinery Unit 2100 distillation towers; the repair procedure used, including sand blasting of the corroded surfaces, grinding of the pits, and welding of those pits whose depth was above a maximum limit, and the use of liquid penetrant to check the repairs made; and hydrostatic testing of the T2201 catalytic cracking unit, which used also cladded metals and on which the pits were much smaller in size and number than those on the distillation units.

Oil sands mining and reclamation cause massive loss of peatland and stored carbon

Science.gov (United States)

Rooney, Rebecca C.; Bayley, Suzanne E.; Schindler, David W.

2012-01-01

We quantified the wholesale transformation of the boreal landscape by open-pit oil sands mining in Alberta, Canada to evaluate its effect on carbon storage and sequestration. Contrary to claims made in the media, peatland destroyed by open-pit mining will not be restored. Current plans dictate its replacement with upland forest and tailings storage lakes, amounting to the destruction of over 29,500 ha of peatland habitat. Landscape changes caused by currently approved mines will release between 11.4 and 47.3 million metric tons of stored carbon and will reduce carbon sequestration potential by 5,734–7,241 metric tons C/y. These losses have not previously been quantified, and should be included with the already high estimates of carbon emissions from oil sands mining and bitumen upgrading. A fair evaluation of the costs and benefits of oil sands mining requires a rigorous assessment of impacts on natural capital and ecosystem services. PMID:22411786

Fisher Sand & Gravel New Mexico, Inc. General Air Quality Permit: Related Documents

Science.gov (United States)

Documents related to the Fisher Sand & Gravel – New Mexico, Inc., Grey Mesa Gravel Pit General Air Quality Permit for New or Modified Minor Source Stone Quarrying, Crushing, and Screening Facilities in Indian Country.

Borrowing Abroad: The Debtor's Perspective

OpenAIRE

Richard N. Cooper; Jeffrey Sachs

1984-01-01

This paper addresses the question of external borrowing from the perspective of the borrowing country. The first section sketches a formal framework for optimal borrowing by a developing country, as seen from the planner's point of view. The next three sections use this framework for the development of three important limits on external borrowing: the problem of solvency, the problem of liquidity and the problem created by the possibility of repudiation. The fifth section relates external bor...

Effects of solar collecting area and water flow rate on the performance of a sand bed solar collector

International Nuclear Information System (INIS)

Maganhar, A.L.; Memon, A.H.; Panhwar, M.I.

2005-01-01

The often discussed renewable sources of energy have been great interest to energy researchers and planners for quite some time. The primary of renewing all sources of energy is the sun. There have been two main problems not yet fully resolved. One is the large scale production of energy and other is the cost factor. In the present study, the cost factor is under consideration. In this regard a non-conventional solar collector using indigenous material (pit sand) as solar absorber is designed and manufactured. This paper presents the results of an investigation of the effect of solar collecting area and water flow rate on the performance of a pit sand bed solar collector especially in terms of rise in water temperature. Three pit sand solar collectors of area 1m/sup 2/ each were connected in series to enhance the collecting area and the system was tested for different flow rates. Experimental results proved that there was increase in water temperature with increase in solar collecting area an decreases in water temperature with increase in flow rate. (author)

Millennium Open Pit Mine, Alberta, Canada

Science.gov (United States)

2007-01-01

Near Fort McMurray, Alberta, Canada, on the east bank of the Athabasca River, are found the Steepbank and Millennium mines. These open pit mines produce oil sands that are processed to recover bitumen, and then upgrade it to refinery-ready raw crude oil, and diesel fuel. The ASTER images were acquired September 22, 2000 and July 31, 2007, cover an area of 22.5 x 25.5 km, and are located near 57 degrees north latitude, 111.5 degrees west longitude. The U.S. science team is located at NASA's Jet Propulsion Laboratory, Pasadena, Calif. The Terra mission is part of NASA's Science Mission Directorate.

Study on the application of permeable reactive barriers for remediation of uranium mine pit water

International Nuclear Information System (INIS)

Li Na'na; Zhu Yucheng

2012-01-01

Permeable reactive barrier (PRB) is economical and convenient on in suit remediation of polluted groundwater. In this paper, according to characteristics of uranium mine pit water, laboratory-scale PRB reactors were designed with the mixture of valent iron, active carbon, hydrated lime and quartz sands as reaction media. The feasibility and effectiveness of treating uranium mine pit water by PRB were tested under 3 different proportions of contaminants through dynamic simulation tests, which came out the optimal proportion of contaminants. The result indicated that the remediation effect of reactor B was the best, whose average removal rate to U was up to 99%. The quality of effluent attained the relevant standards, which indicated that the PRB technology is a feasible method for the treatment of uranium mine pit water. (authors)

7 CFR 1962.46 - Deceased borrowers.

Science.gov (United States)

2010-01-01

... Deceased borrowers. Immediately on learning of the death of any person liable to the Agency, the County... official as directed by OGC or it will be referred by OGC to the U.S. Attorney for filing if representation... the borrower for their support at the time of the borrower's death, continuation may be approved...

Why do Pit-Hours outlive the Pit?

NARCIS (Netherlands)

S.R. Ozturk (Sait); M. van der Wel (Michel); D.J.C. van Dijk (Dick)

2015-01-01

markdownabstract__Abstract__ We study why a majority of trades still happen during the pit hours, i.e. when the trading pit is open, even after the pit ceased to be a liquid and informative venue. We investigate the case of 30-year U.S. Treasury futures using a ten-years-long intraday data set

Morphological assimilation of borrowed terminology (on the example of terminological units, borrowed from French

Directory of Open Access Journals (Sweden)

Kaneeva Anna Vitalievna

2015-06-01

Full Text Available The study of morphological assimilation is an important and mandatory problem as far as the native speaker media will be comfortable using the term of the borrowing language in the flow of speech, without considering the specific grammatical forms, largely determines its subsequent semantic assimilation, its incorporation into a particular terminology system. The analysis clearly shows the place of French borrowings in the morphological system of the Russian language, helps to identify the most significant differences between the structures of the two languages. At the same time it suggests that many French terminology borrowings morphologically assimilated fairly well, there were some groups in the Russian language, which transformed morphologically French elements falling into Russian. This makes borrowings more smooth, and loan word, provided that it actually meets the needs of the language - receptor in the host language adapts quickly and easily absorbed by native speakers

Optic Nerve Pit

Science.gov (United States)

... Conditions Frequently Asked Questions Español Condiciones Chinese Conditions Optic Nerve Pit What is optic nerve pit? An optic nerve pit is a ... may be seen in both eyes. How is optic pit diagnosed? If the pit is not affecting ...

Borrowing Money. Science and Technology Education in Philippine Society.

Science.gov (United States)

Philippines Univ., Quezon City. Inst. for Science and Mathematics Education Development.

This module discusses several borrowing schemes to help students see more clearly the effects of borrowing money on both the lender and the borrower. They include borrowing from personal lenders, from "5-6" operators, and from credit unions. Three exercise sets with answers (one for each borrowing scheme), a short list of references, and…

7 CFR 1717.653 - Borrowers in default.

Science.gov (United States)

2010-01-01

..., to be in the financial interest of the government with respect to loan security and/or repayment. If... AGRICULTURE POST-LOAN POLICIES AND PROCEDURES COMMON TO INSURED AND GUARANTEED ELECTRIC LOANS Investments, Loans, and Guarantees by Electric Borrowers § 1717.653 Borrowers in default. Any borrower not in...

External and Internal Conditionality of Language Borrowing

Directory of Open Access Journals (Sweden)

Лилия Михайловна Букина

2016-12-01

Full Text Available This article looks at the factors that condition borrowings in language. The exposure of borrowings in the language system is based on precise differentiation of intralinguistic and extralinguistic factors. The theoretical basis for this study were the works of Russian and foreign scientists (Bagana Zh., Breiter M.A., Crystal D., Kryisin L.P., et al who were interested in such diversified phenomena as borrowings, in general, and in particular the reasons for them. Research is being conducted on the basis of the French language, certain illustrative units derived empirically in the process of researching these French websites: http://www.linternaute.com, http://www.elle.fr, http://www.wuzz.fr, http://www.eurosport.fr, etc. Borrowing can occur on all levels of language, but we considered the factors that facilitate borrowing and assimilation in the recipient language of lexical borrowings. The research is aimed at considering points of view of different linguists on the problem of borrowing into the recipient language and revealing similarities and differences in the views of scientists. Notwithstanding the fact that external reasons are acting as stimuli for borrowing, there are many linguistic research works that highlight their importance in the appearance and customization of foreign words in the recipient language. Intralinguistic factors dominate in the process of adopting a foreign word into the vocabulary of another language. Psychological factors play one of the key roles in the appearance of borrowings, as language contact is performed when bilingual speakers who have separate linguistic identities communicate. During the research the following methods were used: continuous sampling method, descriptive and analytical method, method of semantic analysis, method of comparison and contrasting.

Oil sands tailings preliminary ecological risk assessment

International Nuclear Information System (INIS)

1994-01-01

Chemical data collected from various oil sands soil-tailings mixtures were used to determine the ecological risk that such tailings would pose to terrestrial wildlife at the surface of a reclaimed site. A methodology that could be used to evaluate the risks posed by various reclamation options (for dry land only) was proposed. Risks associated with other reclamation options, such as wet landscapes or deeper in-pit disposal, were not evaluated. Ten constituents (eight organic and two inorganic) were found to pose a threat to terrestrial biota. The relative contribution of different exposure pathways (water and food ingestion, incidental soil ingestion, inhalation) were studied by probabilistic models. Some physical and chemical reclamation alternatives which involve incorporating oil sands tailings in the landscape to produce a surface that could sustain a productive ecosystem, were described. 53 refs., 15 tabs., 3 figs

Recognition of English and German Borrowings in the Russian Language (Based on Lexical Borrowings in the Field of Economics)

Science.gov (United States)

Ashrapova, Alsu; Alendeeva, Svetlana

2014-01-01

This article is the result of a study of the influence of English and German on the Russian language during the English learning based on lexical borrowings in the field of economics. This paper discusses the use and recognition of borrowings from the English and German languages by Russian native speakers. The use of lexical borrowings from…

Tagging effects of passive integrated transponder and visual implant elastomer on the small-bodied white sands pupfish (Cyprinodon tularosa)

Science.gov (United States)

Peterson, Damon; Trantham, Randi B.; Trantham, Tulley G.; Caldwell, Colleen A.

2018-01-01

One of the greatest limiting factors of studies designed to obtain growth, movement, and survival in small-bodied fishes is the selection of a viable tag. The tag must be relatively small with respect to body size as to impart minimal sub-lethal effects on growth and mobility, as well as be retained throughout the life of the fish or duration of the study. Thus, body size of the model species becomes a major limiting factor; yet few studies have obtained empirical evidence of the minimum fish size and related tagging effects. The probability of surviving a tagging event was quantified in White Sands pupfish (Cyprinodon tularosa) across a range of sizes (19–60 mm) to address the hypothesis that body size predicts tagging survival. We compared tagging related mortality, individual taggers, growth, and tag retention in White Sands pupfish implanted with 8-mm passive integrated transponder (PIT), visual implant elastomer (VIE), and control (handled similarly, but no tag implantation) over a 75 d period. Initial body weight was a good predictor of the probability of survival in PIT- and VIE-tagged fish. As weight increased by 1 g, the fish were 4.73 times more likely to survive PIT-tag implantation compared to the control fish with an estimated suitable tagging size at 1.1 g (TL: 39.29 ± 0.41 mm). Likewise, VIE-tagged animals were 2.27 times more likely to survive a tagging event compared to the control group for every additional 1 g with an estimated size suitable for tagging of 0.9 g (TL: 36.9 ± 0.36 mm) fish. Growth rates of PIT- and VIE-tagged White Sands pupfish were similar to the control groups. This research validated two popular tagging methodologies in the White Sands pupfish, thus providing a valuable tool for characterizing vital rates in other small-bodied fishes.

SEMANTIC DERIVATION OF BORROWINGS

Directory of Open Access Journals (Sweden)

Shigapova, F.F.

2017-09-01

Full Text Available The author carried out the contrastive analysis of the word спикер borrowed into Russian from English and the English word speaker. The findings of the analysis include confirm (1 different derivational abilities and functions of the borrowed word and the native word; (2 distinctive features in the definitions, i.e. semantic structures, registered in monolingual non-abridged dictionaries; (3 heterogeneous parameters of frequencies recorded in the National Corpus of the Russian language and the British National Corpus; (4 absence of bilingual equivalent collocations with words спикер and speaker. The collocations with words studied revealed new lexical and connotative senses in the meaning of the word. Relevance of the study conducted is justified by the new facts revealed about the semantic adaptation of the borrowed word in the system of the Russian language and its paradigmatic and syntagmatic connections in the system of the recipient language.

ENGLISH BORROWINGS IN INDONESIAN NEWSPAPERS

Directory of Open Access Journals (Sweden)

Iwan Fauzi

2015-12-01

Full Text Available This study represents a corpus-based study of English loan words in Bahasa Indonesia used by three foremost newspapers in Indonesia (Kompas, Koran Tempo, and Media Indonesia. There are 19,494 loan tokens of 3,538 loan types extracted from 3,671 texts published online on those media during around three months ranging from 1 April to 24 June 2012. This study compares two basic typologies of borrowing—established and non-established loans. Attestations are looked into in this study proving the evidence that the borrow ability of nouns is higher than otherword categories, linguistic typology of borrowing motivates linguistic adaptation, and word categories give a significant contribution to motivate linguistic adaptation as well. Keywords: sociolinguistics, borrowing, loanwords, morphological integration, linguistic adaptation

12 CFR 615.5030 - Borrowings from commercial banks.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Borrowings from commercial banks. 615.5030... commercial banks. (a) Each System bank board, by resolution, shall authorize all commercial bank borrowings by that System bank. (b) The Financial Assistance Corporation may borrow from commercial banks with...

Lexical Modernization in Nepali: A Study of Borrowing.

Science.gov (United States)

Acharya, Jayaraj

1990-01-01

Focuses on the controversy among Nepali language specialists over the sources of lexical borrowing in Nepali. Lexical items currently are borrowed from both English and Sanskrit, and also Hindi/Urdu, Persian and Arabic. After reviewing Nepali history and language, the question of borrowing from different sources within different domains of…

7 CFR 765.202 - Borrower responsibilities.

Science.gov (United States)

2010-01-01

... or other security instruments; and (2) The cost of lien search reports; (d) Pay taxes on property...) Non-compliance with the provisions of loan agreements and documents, other than failure to meet... FLP loans by the borrower; (2) Borrower non-compliance will be considered by the Agency when making...

34 CFR 685.304 - Counseling borrowers.

Science.gov (United States)

2010-07-01

... 34 Education 3 2010-07-01 2010-07-01 false Counseling borrowers. 685.304 Section 685.304 Education... Direct Loan Program Schools § 685.304 Counseling borrowers. (a) Entrance counseling. (1) Except as provided in paragraph (a)(8) of this section, a school must ensure that entrance counseling is conducted...

Pitting corrosion as a mixed system: coupled deterministic-probabilistic simulation of pit growth

Science.gov (United States)

Ibrahim, Israr B. M.; Fonna, S.; Pidaparti, R.

2018-05-01

Stochastic behavior of pitting corrosion poses a unique challenge in its computational analysis. However, it also stems from electrochemical activity causing general corrosion. In this paper, a framework for corrosion pit growth simulation based on the coupling of the Cellular Automaton (CA) and Boundary Element Methods (BEM) is presented. The framework assumes that pitting corrosion is controlled by electrochemical activity inside the pit cavity. The BEM provides the prediction of electrochemical activity given the geometrical data and polarization curves, while the CA is used to simulate the evolution of pit shapes based on electrochemical activity provided by BEM. To demonstrate the methodology, a sample case of local corrosion cells formed in pitting corrosion with varied dimensions and polarization functions is considered. Results show certain shapes tend to grow in certain types of environments. Some pit shapes appear to pose a higher risk by being potentially significant stress raisers or potentially increasing the rate of corrosion under the surface. Furthermore, these pits are comparable to commonly observed pit shapes in general corrosion environments.

Is Playing in the Pit Really the Pits?: Pain, Strength, Music Performance Anxiety, and Workplace Satisfaction in Professional Musicians in Stage, Pit, and Combined Stage/Pit Orchestras.

Science.gov (United States)

Kenny, Dianna T; Driscoll, Tim; Ackermann, Bronwen J

2016-03-01

Typically, Australian orchestral musicians perform on stage, in an orchestra pit, or in a combination of both workplaces. This study explored a range of physical and mental health indicators in musicians who played in these different orchestra types to ascertain whether orchestra environment was a risk factor affecting musician wellbeing. Participants comprised 380 full-time orchestral musicians from the eight major state orchestras in Australia comprised of two dedicated pit orchestras, three stage-only symphonic orchestras, and three mixed stage/pit orchestras. Participants completed a physical assessment and a range of self-report measures assessing performance-related musculoskeletal disorders (PRMD), physical characteristics including strength and perceived exertion, and psychological health, including music performance anxiety (MPA), workplace satisfaction, and bullying. Physical characteristics and performance-related musculoskeletal profiles were similar for most factors on the detailed survey completed by orchestra members. The exceptions were that pit musicians demonstrated greater shoulder and elbow strength, while mixed-workload orchestra musicians had greater flexibility Significantly more exertion was reported by pit musicians when rehearsing and performing. Stage/pit musicians reported less physical exertion when performing in the pit compared with performing on stage. Severity of MPA was significantly greater in pit musicians than mixed orchestra musicians. Pit musicians also reported more frequent bullying and lower job satisfaction compared with stage musicians. There were few differences in the objective physical measures between musicians in the different orchestra types. However, pit musicians appear more psychologically vulnerable and less satisfied with their work than musicians from the other two orchestra types. The physical and psychological characteristics of musicians who perform in different orchestra types have not been adequately

The Impact of Bank Consolidation on Commercial Borrower Welfare

NARCIS (Netherlands)

Karceski, J.; Ongena, S.; Smith, D.C.

2000-01-01

We estimate the impact of bank merger announcements on borrowers' stock prices for publicly-traded Norwegian firms.In addition, we analyze how bank mergers influence borrower relationship termination behavior and relate the propensity to terminate to borrower abnormal returns.We obtain four main

Studying borrower level risk characteristics of education loan in India

Directory of Open Access Journals (Sweden)

Arindam Bandyopadhyay

2016-09-01

Full Text Available This paper empirically investigates the granular level risk of education loan using a cross section of data from 5000 borrowers obtained from four major public sector banks in India. The findings suggest that education loan defaults are mainly influenced by security, borrower margin, and repayment periods. The presence of guarantor or co-borrower and collateral significantly reduce default loss rates. The socioeconomic characteristics of borrowers and their regional locations also act as important factors associated with education loan defaults. The results suggest that by segmenting borrowers by probability of default and loss given default in a multidimensional scale, banks can adopt better risk mitigation and pricing strategies to resolve borrower problems.

The role and importance of the enterprise`s borrowed capital

Directory of Open Access Journals (Sweden)

Dombrovska Sofiіa Oleksiyivna

2016-06-01

Full Text Available The paper presents scientific views of researches regarding the definition of “borrowed capital”. The basic functions of borrowed capital have been submitted, its classification on various grounds is highlighted. The article describes the features of borrowed capital, its advantages and disadvantages, considers management system of borrowed capital and problems of domestic enterprises in modern conditions of economic relations. The author proposed the main directions of the management improving of borrowed capital. The information will be useful for specialists in the field of financial management.

CHerenkov detectors In mine PitS (CHIPS) Letter of Intent to FNAL

Energy Technology Data Exchange (ETDEWEB)

Adamson, P. [Fermi National Accelerator Laboratory (FNAL), Batavia, IL (United States); Austin, J. [Univ. of Minnesota, Duluth, MN (United States); Cao, S. V. [Univ. of Texas, Austin, TX (United States); Coelho, J. A. B. [Tufts Univ., Medford, MA (United States); Davies, G. S. [Iowa State Univ., Ames, IA (United States); Evans, J. J. [Univ. of Manchester (United Kingdom); Guzowski, P. [Univ. of Manchester (United Kingdom); Habig, A. [Univ. of Minnesota, Duluth, MN (United States); Holin, A. [Univ. College London, London (United Kingdom); Huang, J. [Univ. of Texas, Austin, TX (United States); Johnson, R. [Univ. of Cincinnati, OH (United States); St. John, J. [Univ. of Cincinnati, OH (United States); Kreymer, A. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Kordosky, M. [College of William and Mary, Williamsburg, VA (United States); Lang, K. [Univ. of Texas, Austin, TX (United States); Marshak, M. L. [Univ. of Minnesota, Minneapolis, MN (United States); Mehdiyev, R. [Univ. of Texas, Austin, TX (United States); Meier, J. [Univ. of Minnesota, Minneapolis, MN (United States); Miller, W. [Univ. of Minnesota, Minneapolis, MN (United States); Naples, D. [Univ. of Pittsburgh, PA (United States); Nelson, J. K. [College of William and Mary, Williamsburg, VA (United States); Nichol, R. J. [Univ. College London, London (United Kingdom); Patterson, R. B. [California Inst. of Technology (CalTech), Pasadena, CA (United States); Paolone, V. [Univ. of Pittsburgh, PA (United States); Pawloski, G. [Univ. of Minnesota, Minneapolis, MN (United States); Perch, A. [Univ. College London, London (United Kingdom); Pfutzner, M. [Univ. College London, London (United Kingdom); Proga, M. [Univ. of Texas, Austin, TX (United States); Qian, X. [Brookhaven National Lab. (BNL), Upton, NY (United States); Radovic, A. [Univ. College London, London (United Kingdom); Sanchez, M. C. [Iowa State Univ., Ames, IA (United States); Schreiner, S. [Univ. of Minnesota, Minneapolis, MN (United States); Soldner-Rembold, S. [Univ. of Manchester (United Kingdom); Sousa, A. [Univ. of Cincinnati, OH (United States); Thomas, J. [Univ. College London, London (United Kingdom); Vahle, P. [College of William and Mary, Williamsburg, VA (United States); Wendt, C. [Univ. of Wisconsin, Madison, WI (United States); Whitehead, L. H. [Univ. College London, London (United Kingdom); Wojcicki, S. [Stanford Univ., CA (United States)

2013-12-30

This Letter of Intent outlines a proposal to build a large, yet cost-effective, 100 kton fiducial mass water Cherenkov detector that will initially run in the NuMI beam line. The CHIPS detector (CHerenkov detector In Mine PitS) will be deployed in a flooded mine pit, removing the necessity and expense of a substantial external structure capable of supporting a large detector mass. There are a number of mine pits in northern Minnesota along the NuMI beam that could be used to deploy such a detector. In particular, the Wentworth Pit 2W is at the ideal off-axis angle to contribute to the measurement of the CP violating phase. The detector is designed so that it can be moved to a mine pit in the LBNE beam line once that becomes operational.

Stochastic modeling of pitting corrosion: A new model for initiation and growth of multiple corrosion pits

International Nuclear Information System (INIS)

Valor, A.; Caleyo, F.; Alfonso, L.; Rivas, D.; Hallen, J.M.

2007-01-01

In this work, a new stochastic model capable of simulating pitting corrosion is developed and validated. Pitting corrosion is modeled as the combination of two stochastic processes: pit initiation and pit growth. Pit generation is modeled as a nonhomogeneous Poisson process, in which induction time for pit initiation is simulated as the realization of a Weibull process. In this way, the exponential and Weibull distributions can be considered as the possible distributions for pit initiation time. Pit growth is simulated using a nonhomogeneous Markov process. Extreme value statistics is used to find the distribution of maximum pit depths resulting from the combination of the initiation and growth processes for multiple pits. The proposed model is validated using several published experiments on pitting corrosion. It is capable of reproducing the experimental observations with higher quality than the stochastic models available in the literature for pitting corrosion

Stochastic modeling of pitting corrosion: A new model for initiation and growth of multiple corrosion pits

Energy Technology Data Exchange (ETDEWEB)

Valor, A. [Facultad de Fisica, Universidad de La Habana, San Lazaro y L, Vedado, 10400 Havana (Cuba); Caleyo, F. [Departamento de Ingenieria, Metalurgica, IPN-ESIQIE, UPALM Edif. 7, Zacatenco, Mexico DF 07738 (Mexico)]. E-mail: fcaleyo@gmail.com; Alfonso, L. [Departamento de Ingenieria, Metalurgica, IPN-ESIQIE, UPALM Edif. 7, Zacatenco, Mexico DF 07738 (Mexico); Rivas, D. [Departamento de Ingenieria, Metalurgica, IPN-ESIQIE, UPALM Edif. 7, Zacatenco, Mexico DF 07738 (Mexico); Hallen, J.M. [Departamento de Ingenieria, Metalurgica, IPN-ESIQIE, UPALM Edif. 7, Zacatenco, Mexico DF 07738 (Mexico)

2007-02-15

In this work, a new stochastic model capable of simulating pitting corrosion is developed and validated. Pitting corrosion is modeled as the combination of two stochastic processes: pit initiation and pit growth. Pit generation is modeled as a nonhomogeneous Poisson process, in which induction time for pit initiation is simulated as the realization of a Weibull process. In this way, the exponential and Weibull distributions can be considered as the possible distributions for pit initiation time. Pit growth is simulated using a nonhomogeneous Markov process. Extreme value statistics is used to find the distribution of maximum pit depths resulting from the combination of the initiation and growth processes for multiple pits. The proposed model is validated using several published experiments on pitting corrosion. It is capable of reproducing the experimental observations with higher quality than the stochastic models available in the literature for pitting corrosion.

42 CFR 60.10 - How much can be borrowed?

Science.gov (United States)

2010-10-01

... school of public health, pharmacy, chiropractic, or a graduate program in health administration, clinical... pursuing a similar curriculum at that school. (b) Non-student borrower. An eligible nonstudent may borrow... 42 Public Health 1 2010-10-01 2010-10-01 false How much can be borrowed? 60.10 Section 60.10...

Sand and gravel mining: effects on ground water resources in Hancock county, Maine, USA

Science.gov (United States)

Peckenham, John M.; Thornton, Teresa; Whalen, Bill

2009-01-01

Based on this preliminary study, existing sand and gravel mining regulations (in Maine, USA) can be inferred to provide some protection to water resources. Sand and gravel deposits are important natural resources that have dual uses: mining for construction material and pumping for drinking water. How the mining of sand and gravel affects aquifers and change aquifer vulnerability to contamination is not well documented. Mining regulations vary greatly by state and local jurisdiction. This study test metrics to measure the effectiveness of mining regulations. The sand and gravel aquifer system studied is covered with former and active gravel pits to nearly 25% of its areal extent. Data from homeowner interviews and field measurements found scant evidence of changes in water quantity. Water quality analyses collected from springs, streams, ponds and wells indicate that the aquifer was vulnerable to contamination by chloride and nitrate. However, water quality changes can not be related directly to mining activities.

34 CFR 685.206 - Borrower responsibilities and defenses.

Science.gov (United States)

2010-07-01

... parent borrower, of the student, including any Federal Consolidation Loan or Direct Consolidation Loan... enrollment status, financial assistance, and employment records). (b)(1) The borrower shall promptly notify...

Effective Counseling, Empowered Borrowers: An Evidence-Based Policy Agenda for Informed Student Loan Borrowing and Repayment. Research Report

Science.gov (United States)

Fernandez, Chris

2016-01-01

To manage their loans effectively, U.S. postsecondary student loan borrowers must make a variety of important decisions that require significant knowledge and financial skills and entail considerable risk. Federal law requires colleges to provide student loan counseling to their federal student loan borrowers, but there is significant room for…

12 CFR 615.5250 - Disclosure requirements for borrower stock.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Disclosure requirements for borrower stock. 615... Disclosure requirements for borrower stock. (a) For sales of borrower stock, which for this subpart means... an at-risk investment and not a compensating balance; (ii) That the equity is retireable only at the...

Analysis of disposal of uranium mill tailings in a mined out open pit

International Nuclear Information System (INIS)

Staub, W.P.; Triegel, E.K.

1978-08-01

Mined out open pits are presently under consideration as disposal sites for uranium mill tailings. In this method of tailings management, the escape of contaminated liquid into an adjacent aquifer is the principal environmental concern. The modified Bishop Method was used to analyze the structural stability of a clay liner along the highwall and fluid flow models were used to analyze the effect of tailings solutions on groundwater under several operating conditions. The slope stability of a clay liner was analyzed at three stages of operation: (1) near the beginning of construction, (2) when the pit is partially filled with tailings, and (3) at the end of construction. Both clay lined and unlined pits were considered in the fluid flow modeling. Finally, the seepage of tailings solutions through the clay liner was analyzed. Results of the slope stability analysis showed that it would be necessary to construct the clay liner as a modified form of engineered embankment. This embankment would be similar in construction to that of an earthfill dam. It could be constructed on a 1 : 1 slope provided the tailings slurry were managed properly. It would be necessary to maintain the freeboard height between the embankment and tailings at less than 4 m. A partially dewatered sand beach would have to be located adjacent to the embankment. Potential leakage and aquifer contamination was modeled for lined and unlined pits of various designs. Sulfate, and possibly U and Th, are the most likely contaminants. Results from the model showed the clay and soil cement lined pit to be most effective in containing the pollutants

7 CFR 1755.27 - Borrower contractual obligations.

Science.gov (United States)

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Borrower contractual obligations. 1755.27 Section 1755.27 Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE... CONTRACT FORMS § 1755.27 Borrower contractual obligations. (a) Loan agreement. As a condition of a loan or...

7 CFR 765.101 - Borrower graduation requirements.

Science.gov (United States)

2010-01-01

... reasonable rates and terms. (b) The Agency may require partial or full graduation. (1) In a partial... 7 Agriculture 7 2010-01-01 2010-01-01 false Borrower graduation requirements. 765.101 Section 765..., DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS DIRECT LOAN SERVICING-REGULAR Borrower Graduation § 765.101...

Comparative analysis of informal borrowing behaviour between ...

African Journals Online (AJOL)

Tools of analyses were descriptive statistics of mean and percentages and probit model, The result of the Probit model on the variables influencing borrowing behaviour of male-headed households indicated that the coefficients of household size, farm size, purpose of borrowing, loan duration, interest rate and collateral ...

Impact Of Microcredit Programs On Higher Income Borrowers: Evidence From Bangladesh

OpenAIRE

Sayma Rahman; Rafiqul Bhuyan Rafiq; Mohammad A. Momen

2011-01-01

In this study, we investigate the impact of microcredit on economic indicators of borrowers in Bangladesh and compare if the impact is same across borrowers having different income levels. Our estimation results show that the microcredit programs are effective in generating higher income and assets for borrowers in general. However, the impact is not found to be uniform across income levels of borrowers. Higher income borrowers seem to be better off compared to the middle and lower income bor...

7 CFR 766.104 - Borrower eligibility requirements.

Science.gov (United States)

2010-01-01

... economic conditions such as low commodity prices; (iv) Damage or destruction of property essential to the farming operation; or (v) Loss of, or reduction in, the borrower or spouse's essential non-farm income. (2) The borrower does not have non-essential assets for which the net recovery value is sufficient to...

7 CFR 1724.71 - Borrower contractual obligations.

Science.gov (United States)

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Borrower contractual obligations. 1724.71 Section... Contract Forms § 1724.71 Borrower contractual obligations. (a) Loan agreement. As a condition of a loan or... obligation is contained in section 5.16 of the loan contract. To comply with the provisions of the loan...

7 CFR 1726.301 - Borrower contractual obligations.

Science.gov (United States)

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Borrower contractual obligations. 1726.301 Section... Borrower contractual obligations. (a) Loan agreement. As a condition of a loan or loan guarantee under the... obligation is contained in section 5.16 of the loan contract. To comply with the provisions of the loan...

A probability distribution model of tooth pits for evaluating time-varying mesh stiffness of pitting gears

Science.gov (United States)

Lei, Yaguo; Liu, Zongyao; Wang, Delong; Yang, Xiao; Liu, Huan; Lin, Jing

2018-06-01

Tooth damage often causes a reduction in gear mesh stiffness. Thus time-varying mesh stiffness (TVMS) can be treated as an indication of gear health conditions. This study is devoted to investigating the mesh stiffness variations of a pair of external spur gears with tooth pitting, and proposes a new model for describing tooth pitting based on probability distribution. In the model, considering the appearance and development process of tooth pitting, we model the pitting on the surface of spur gear teeth as a series of pits with a uniform distribution in the direction of tooth width and a normal distribution in the direction of tooth height, respectively. In addition, four pitting degrees, from no pitting to severe pitting, are modeled. Finally, influences of tooth pitting on TVMS are analyzed in details and the proposed model is validated by comparing with a finite element model. The comparison results show that the proposed model is effective for the TVMS evaluations of pitting gears.

Analysis of disposal of uranium mill tailings in a mined out open pit

International Nuclear Information System (INIS)

Staub, W.P.; Triegel, E.K.

1978-01-01

Mined out open pits are presently under consideration as disposal sites for uranium mill tailings. In this method of tailings management, the escape of contaminated liquid into an adjacent aquifer is the principal environmental concern. The modified Bishop Method was used to analyze the structural stability of a clay liner along the highwall and fluid flow models were used to analyze the effect of tailings solutions on ground water under several operating conditions. Results of the slope stability analysis showed that it would be necessary to construct the clay liner as a modified form of engineered embankment. This embankment would be similar in construction to that of an earthfill dam. It could be constructed on a 1:1 slope provided the tailings slurry were managed properly. It would be necessary to maintain the freeboard height between the embankment and tailings at less than 4 m. A partially dewatered sand beach would have to be located adjacent to the embankment. Potential leakage and aquifer contamination was modeled for lined and unlined pits of various designs. Sulfate, and possibly U and Th, are the most likely contaminants. Results from the model showed the clay and soil cement lined pit to be most effective in containing the pollutants

Finance Companies and Small Business Borrowers: An Empirical Investigation

OpenAIRE

Haynes, George; Watts, Myles

1996-01-01

Finance companies have been perceived as isolated and insignificant lenders, attracting high risk borrowers and charging these borrowers relatively high prices. Using the 1988 National Survey of Small Business Finance, this study examines the relationship between finance companies and other lenders, describes the characteristics of borrowers attracted to finance companies and assesses whether finance companies charge higher loan prices and impose more stringent collateral requirements on thei...

24 CFR 201.23 - Borrower's initial payment.

Science.gov (United States)

2010-04-01

... gift or a loan from some other source, the borrower must disclose the source of such gift or loan on... lender in the loan file. (b) Manufactured home purchase loans. In the case of a manufactured home purchase loan, the borrower shall make a minimum cash downpayment of at least five percent of the purchase...

7 CFR 1724.20 - Borrowers' requirements-architectural services.

Science.gov (United States)

2010-01-01

... UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE ELECTRIC ENGINEERING, ARCHITECTURAL SERVICES AND DESIGN POLICIES AND PROCEDURES Architectural Services § 1724.20 Borrowers' requirements—architectural services... 7 Agriculture 11 2010-01-01 2010-01-01 false Borrowers' requirements-architectural services. 1724...

Tank Riser Pit Decontamination System (Pit Viper) Return on Investment and Break-Even Analysis

International Nuclear Information System (INIS)

Young, Joan K.; Weimar, Mark R.; Balducci, Patrick J.; Fassbender, Linda L.; Hernandez, Melissa

2003-01-01

This study assessed the cost benefit of Pit Viper deployment for 80 tank farm pits between October 1, 2003 and September 30, 2012 under the technical baseline for applicable double-shell tank (DST) and single-shell tank (SST) projects. After this assessment had been completed, the U.S. Department of Energy (DOE) Richland Operations Office (RL) and Office of River Protection (ORP) published the Hanford Performance Management Plan (August 2003), which accelerated the schedule for SST retrieval. Then, DOE/CH2M HILL contract modification M064 (October 2002) and The Integrated Mission Acceleration Plan (March 2003) further accelerated SST retrieval and closure schedules. Twenty-six to 40 tanks must be retrieved by 2006. Thus the schedule for SST pit entries is accelerated and the number of SST pit entries is increased. This study estimates the return on investment (ROI) and the number of pits where Pit Viper deployment would break even or save money over current manual practices. The results of the analysis indicate a positive return on the federal investment for deployment of the Pit Viper provided it is used on a sufficient number of pits

Hydraulic fracture considerations in oil sand overburden dams

Energy Technology Data Exchange (ETDEWEB)

Cameron, R.; Madden, B.; Danku, M. [Syncrude Canada Ltd., Fort McMurray, AB (Canada)

2008-07-01

This paper discussed hydraulic fracture potential in the dry-filled temporary dams used in the oil sands industry. Hydraulic fractures can occur when reservoir fluid pressures are greater than the minimum stresses in a dam. Stress and strain conditions are influenced by pore pressures, levels of compaction in adjacent fills as well as by underlying pit floor and abutment conditions. Propagation pressure and crack initiation pressures must also be considered in order to provide improved hydraulic fracture protection to dams. Hydraulic fractures typically result in piping failures. Three cases of hydraulic fracture at oil sands operations in Alberta were presented. The study showed that hydraulic fracture failure modes must be considered in dam designs, particularly when thin compacted lift of dry fill are used to replace wetted clay cores. The risk of hydraulic fractures can be reduced by eliminating in situ bedrock irregularities and abutments. Overpressure heights, abutment sloping, and the sloping of fills above abutments, as well as the dam's width and base conditions must also be considered in relation to potential hydraulic fractures. It was concluded that upstream sand beaches and internal filters can help to prevent hydraulic fractures in dams in compacted control zones. 5 refs., 16 figs.

Pit Water Storage Ottrupgaard

DEFF Research Database (Denmark)

Heller, Alfred

2000-01-01

The pit water storage, a seasonal thermal storage, was built in 1993 with floating lid and hybrid clay-polymer for pit lining. The storage was leaking severe and solutions were to be found. In the paper solutions for pit lining and floating lids are discussed, cost estimations given and coming...

Open Pit Water Control Safety A Case Of Nchanga Open Pit Mine Zambia

Directory of Open Access Journals (Sweden)

Silwamba C

2015-08-01

Full Text Available Abstract Mining in Chingola Zambia started underground in 1931 and was catastrophically flooded and closed. The present Nchanga Underground Mine NUG started in 1937. The Nchanga Open Pit NOP mine started in 1955 situated to the west of NUG and partially overlying it. Open pit water control safety operations in the Nchanga-Chingola area have successfully enabled the safe extraction of millions of tonnes of copper ore annually over the past 60 years from NUG mining as well as the NOP. At the start Nchanga mining license surface already had NUG and many watershed divides with the Nchanga and Chingola streams being the main streams feeding into Zambias second largest river Kafue river and 42 of the year was characterised by heavy rains ranging between 800mm to 1300mm per annum. In this paper the presence of very significant amounts of seasonal rain and subsurface water in the mining area was identified as both a curse and a blessing. An excess in seasonal rain and subsurface water would disrupt both open pit and underground mining operations. In order for NOP to be operated successfully stable and free from flooding coping water management tactics were adopted from 1955 to 2015 including 1. Underground mine pump chamber pumping system 2. Piezometer instrumented boreholes 3. Underground mine 1500-ft sub-haulage east borehole dewatering beneath the open pit 4. Nchanga and Chingola stream diversionary tunnel and open drains 5. Nchanga stream causeway and embankment dam in the Matero School Golf Club area 6. Pit perimeter borehole pumping 7. Outer and inner pit perimeter drains and bund walls 8. In-pit ramp side drains 9. In-pit sub-horizontal borehole geo-drains and water and 10. Pit bottom sump pumps. Application of grout curtains along the Vistula River Poland was noted as a possibility in the right circumstances although it had never been used at Nchanga Open Pit. An additional conclusion was that forward health safety and environmental end

Sand and gravel mine operations and reclamation planning using microcomputers

Energy Technology Data Exchange (ETDEWEB)

Ariffin, J.B.

1990-02-01

The purpose of this study is to focus on the application of microcomputers, also known as personal computers, in planning for sand and gravel mine operations and reclamation at a site in Story County, Iowa. This site, called the Arrasmith Pit, is operated by Martin Marietta Aggregates, Inc. The Arrasmith site, which encompasses an area of about 25 acres, is a relatively small site for aggregate mining. However, planning for the concurrent mine operation and reclamation program at this site is just as critical as with larger sites and the planning process is the same.

Uptake of calcium-45 by apple trees at different levels of moisture in relation to the occurrence of bitter pit

International Nuclear Information System (INIS)

Hanekom, A.N.; Deist, J.; Blommaert, K.L.J.

1975-01-01

Uptake and translocation of recently absorbed Ca ( 45 Ca) and total calcium by Golden Delicious apple trees grown in sand culture at different moisture levels were investigated in relation to bitter pit. Growth and development of the trees were significantly retarded by low moisture supply. Moisture stress not only lowered calcium uptake and/or translocation but also significantly decreased the concentration of recently absorbed calcium in the different parts of the tree. Except for the leaves where moisture stress significantly decreased the total calcium concentration, it did not affect the concentration in other parts of the tree. Although the fruit contributed only 5,8% to the total calcium content of the top parts of the tree, this amount of Ca realised a sufficiently high calcium concentration in the fruit to prevent bitter pit. There was no correlation within the experimental period between moisture supply to the trees and the calcium concentration in the fruit or the incidence of bitter pit [af

Compelling Untruths: Content Borrowing and Vivid False Memories

Science.gov (United States)

Lampinen, James Michael; Meier, Christopher R.; Arnal, Jack D.; Leding, Juliana K.

2005-01-01

False memories are sometimes accompanied by surprisingly vivid experiential detail that makes them difficult to distinguish from actual memories. Such strikingly real false memories may be produced by a process called content borrowing in which details from presented items are errantly borrowed to corroborate the occurrence of the false memory…

7 CFR 1717.158 - Mergers with borrowers who prepaid RUS loans.

Science.gov (United States)

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Mergers with borrowers who prepaid RUS loans. 1717.158 Section 1717.158 Agriculture Regulations of the Department of Agriculture (Continued) RURAL... GUARANTEED ELECTRIC LOANS Mergers and Consolidations of Electric Borrowers § 1717.158 Mergers with borrowers...

Phonological Adaptation of Borrowed Terms in Duramazwi reMimhanzi

Directory of Open Access Journals (Sweden)

Gift Mheta

2011-10-01

Full Text Available Abstract: This article analyses the phonological characteristics of Shona musical terms borrowed from English. It discusses the phonological processes that take place when words are borrowed directly or indi-rectly from English. Essentially, the article analyses the adoption and adaptation of Shona loan-words at phonological level. It draws examples from the dictionary of Shona musical terms Duramazwi reMimhanzi (2005. This exploration of loan-word adaptation enhances the understanding of the phonological changes that the musical terms undergo during the borrowing process.

Lexical Borrowing from Chinese Languages in Malaysian English

Science.gov (United States)

Imm, Tan Siew

2009-01-01

This paper explores how contact between English and Chinese has resulted in the incorporation of Chinese borrowings into the lexicon of Malaysian English (ME). Using a corpus-based approach, this study analyses a comprehensive range of borrowed features extracted from the Malaysian English Newspaper Corpus (MEN Corpus). Based on the contexts of…

NELL-1 increases pre-osteoblast mineralization using both phosphate transporter Pit1 and Pit2

Energy Technology Data Exchange (ETDEWEB)

Cowan, Catherine M. [Department of Bioengineering, University of California, Los Angeles, 420 Westwood Plaza,7523 Boelter Hall, Los Angeles, CA 90095 (United States); Dental and Craniofacial Research Institute and Section of Orthodontics, School of Dentistry, University of California, Los Angeles, 40833 Le Conte Ave, Los Angeles, CA 90095 (United States); Zhang, Xinli; James, Aaron W.; Mari Kim, T.; Sun, Nichole [Dental and Craniofacial Research Institute and Section of Orthodontics, School of Dentistry, University of California, Los Angeles, 40833 Le Conte Ave, Los Angeles, CA 90095 (United States); Wu, Benjamin [Department of Bioengineering, University of California, Los Angeles, 420 Westwood Plaza,7523 Boelter Hall, Los Angeles, CA 90095 (United States); Dental and Craniofacial Research Institute and Section of Orthodontics, School of Dentistry, University of California, Los Angeles, 40833 Le Conte Ave, Los Angeles, CA 90095 (United States); Ting, Kang [Dental and Craniofacial Research Institute and Section of Orthodontics, School of Dentistry, University of California, Los Angeles, 40833 Le Conte Ave, Los Angeles, CA 90095 (United States); Soo, Chia, E-mail: bsoo@ucla.edu [UCLA and Orthopaedic Hospital Department of Orthopaedic Surgery and the Orthopaedic, Hospital Research Center, University of California, Los Angeles, 2641 Charles E. Young Dr. South, Los Angeles, CA 90095 (United States)

2012-06-08

Highlights: Black-Right-Pointing-Pointer NELL-1 accelerates extracellular matrix mineralization in MC3T3-E1 pre-osteoblasts. Black-Right-Pointing-Pointer NELL-1 significantly increases intracellular inorganic phosphate levels. Black-Right-Pointing-Pointer NELL-1 positively regulates osteogenesis but not proliferation in MC3T3-E1 cells. Black-Right-Pointing-Pointer NELL-1 regulates inorganic phosphate transporter activity. -- Abstract: NELL-1 is a potent osteoinductive molecule that enhances bone formation in multiple animal models through currently unidentified pathways. In the present manuscript, we hypothesized that NELL-1 may regulate osteogenic differentiation accompanied by alteration of inorganic phosphate (Pi) entry into the osteoblast via sodium dependent phosphate (NaPi) transporters. To determine this, MC3T3-E1 pre-osteoblasts were cultured in the presence of recombinant human (rh)NELL-1 or rhBMP-2. Analysis was performed for intracellular Pi levels through malachite green staining, Pit-1 and Pit-2 expression, and forced upregulation of Pit-1 and Pit-2. Results showed rhNELL-1 to increase MC3T3-E1 matrix mineralization and Pi influx associated with activation of both Pit-1 and Pit-2 channels, with significantly increased Pit-2 production. In contrast, Pi transport elicited by rhBMP-2 showed to be associated with increased Pit-1 production only. Next, neutralizing antibodies against Pit-1 and Pit-2 completely abrogated the Pi influx effect of rhNELL-1, suggesting rhNELL-1 is dependent on both transporters. These results identify one potential mechanism of action for rhNELL-1 induced osteogenesis and highlight a fundamental difference between NELL-1 and BMP-2 signaling.

NELL-1 increases pre-osteoblast mineralization using both phosphate transporter Pit1 and Pit2

International Nuclear Information System (INIS)

Cowan, Catherine M.; Zhang, Xinli; James, Aaron W.; Mari Kim, T.; Sun, Nichole; Wu, Benjamin; Ting, Kang; Soo, Chia

2012-01-01

Highlights: ► NELL-1 accelerates extracellular matrix mineralization in MC3T3-E1 pre-osteoblasts. ► NELL-1 significantly increases intracellular inorganic phosphate levels. ► NELL-1 positively regulates osteogenesis but not proliferation in MC3T3-E1 cells. ► NELL-1 regulates inorganic phosphate transporter activity. -- Abstract: NELL-1 is a potent osteoinductive molecule that enhances bone formation in multiple animal models through currently unidentified pathways. In the present manuscript, we hypothesized that NELL-1 may regulate osteogenic differentiation accompanied by alteration of inorganic phosphate (Pi) entry into the osteoblast via sodium dependent phosphate (NaPi) transporters. To determine this, MC3T3-E1 pre-osteoblasts were cultured in the presence of recombinant human (rh)NELL-1 or rhBMP-2. Analysis was performed for intracellular Pi levels through malachite green staining, Pit-1 and Pit-2 expression, and forced upregulation of Pit-1 and Pit-2. Results showed rhNELL-1 to increase MC3T3-E1 matrix mineralization and Pi influx associated with activation of both Pit-1 and Pit-2 channels, with significantly increased Pit-2 production. In contrast, Pi transport elicited by rhBMP-2 showed to be associated with increased Pit-1 production only. Next, neutralizing antibodies against Pit-1 and Pit-2 completely abrogated the Pi influx effect of rhNELL-1, suggesting rhNELL-1 is dependent on both transporters. These results identify one potential mechanism of action for rhNELL-1 induced osteogenesis and highlight a fundamental difference between NELL-1 and BMP-2 signaling.

Understanding Indonesian People Borrowing Money from Banks and Non-Banking Institutions

Directory of Open Access Journals (Sweden)

Roro Hindun

2016-12-01

Full Text Available People’s borrowing behaviours are influenced by the need to fulfil their basic needs which always change in maintaining their lifestyles. This thesis analyzes the tendency of Indonesians to borrowing money, either from banks or non-banking institutions. This research was carried out using quantitative data analysis with secondary data from the Indonesian Family Life Survey panel data versions 3 and 4. The data was analyzed using STATA 12.0 software. The results of the study show that the significant factors that affect people’s behaviour in borrowing from either banks or non-banking institutions are amount of debt, assets, income, and location; while the insignificant factors are age, religion, and number of householders.   Keywords: money borrowing, borrowing behaviour, debt, IFLS, STATA

Single pit propagation on austenitic stainless steel

International Nuclear Information System (INIS)

Heurtault, Stephane

2016-01-01

The electrochemical characterization of metastable events such as pitting corrosion of stainless steel in chloride electrolyte remains complex because many individual processes may occur simultaneously on the alloy surface. To overcome these difficulties, an experimental setup, the flow micro-device, has been developed to achieve the initiation of a single pit and to propagate the single pit in three dimensions. In this work, we take advantage of such a device in order to revisit the pitting process on a 316L stainless steel in a chloride - sulphate bulk. In a first step, the time evolution of the pit geometry (depth, radius) and the chemical evolution of the pit solution investigated using in situ Raman spectroscopy have shown that the pit depth propagation depends on the formation of a metal chloride and sulphate gel in the pit solution, and is controlled by the metallic cations diffusion from the pit bottom to the pit mouth. The pit radius growth is defined by the initial surface de-passivation, by the presence of a pit cover and by the gel development in the solution. all of these phenomena are function of applied potential and chemical composition of the solution. In a last step, it was demonstrated that a critical chloride concentration is needed in order to maintain the pit propagation. This critical concentration slightly increases with the pit depth. From statistical analysis performed on identical experiments, a zone diagram showing the pit stability as a function of the chloride concentration and the pit dimensions was built. (author) [fr

Lexical Borrowings in the ESL Classrooms in Malaysia

Science.gov (United States)

Thirusanku, Jantmary; Yunus, Melor Md

2013-01-01

This paper attempts to show the use of lexical borrowings in ten teaching materials used by the English as Second Language (ESL) teachers in the ESL classrooms in the National Secondary Schools in the Klang district in Selangor, Malaysia. It also discusses the general and pedagogical implications involved in using lexical borrowings. This paper…

7 CFR 1806.28 - Borrowers required to escrow.

Science.gov (United States)

2010-01-01

... insufficient funds to pay the flood insurance premium when due, the County Supervisor will request the borrower to pay an amount equal to the difference between the premium due and the escrow balance in a lump sum within 30 days after notification. If the borrower fails to remit the amount requested, the amount will...

Public Investment, Revenue Shocks, and Borrowing Restrictions

OpenAIRE

Büttner, Thiess; Wildasin, David E.

2010-01-01

This paper lays out a theory of taxation and public investment in an intertemporal setting under conditions of revenue shocks. Without borrowing restrictions, the optimal policy is characterized by smooth time paths of taxes and public investment. While the introduction of formal borrowing restrictions leads to some precautionary savings, it gives rise to fluctuations in public investment in response to adverse but also favorable revenue shocks. This theoretical result is tested empirically u...

Interacting Effects Induced by Two Neighboring Pits Considering Relative Position Parameters and Pit Depth

Directory of Open Access Journals (Sweden)

Yongfang Huang

2017-04-01

Full Text Available For pre-corroded aluminum alloy 7075-T6, the interacting effects of two neighboring pits on the stress concentration are comprehensively analyzed by considering various relative position parameters (inclination angle θ and dimensionless spacing parameter λ and pit depth (d with the finite element method. According to the severity of the stress concentration, the critical corrosion regions, bearing high susceptibility to fatigue damage, are determined for intersecting and adjacent pits, respectively. A straightforward approach is accordingly proposed to conservatively estimate the combined stress concentration factor induced by two neighboring pits, and a concrete application example is presented. It is found that for intersecting pits, the normalized stress concentration factor Ktnor increases with the increase of θ and λ and always reaches its maximum at θ = 90°, yet for adjacent pits, Ktnor decreases with the increase of λ and the maximum value appears at a slight asymmetric location. The simulations reveal that Ktnor follows a linear and an exponential relationship with the dimensionless depth parameter Rd for intersecting and adjacent cases, respectively.

7 CFR 1951.264 - Action when borrower fails to cooperate, respond or graduate.

Science.gov (United States)

2010-01-01

... Analyzing Credit Needs and Graduation of Borrowers § 1951.264 Action when borrower fails to cooperate, respond or graduate. (a) When borrowers with other than FCP loans fail to: (1) Provide information... appeal the decision. (b) If an FCP borrower fails to cooperate after a lender expresses a willingness to...

Storm-generated bedforms and relict dissolution pits and channels on the Yucatan carbonate platform

Science.gov (United States)

Gulick, S. P.; Goff, J. A.; Stewart, H. A.; Perez-Cruz, L. L.; Davis, M. B.; Duncan, D.; Saustrup, S.; Sanford, J. C.; Fucugauchi, J. U.

2013-12-01

The Yucatan 2013 (cruise number 2013/4_ECORD) geophysical and geotechnical hazard site survey took place aboard the R/V Justo Sierra in April 2013. Our study was conducted within the Chicxulub impact crater, encompassing three potential IODP drilling sites. The survey was located ~32 km northwest of Progreso, Mexico; data acquired included ~15.6 km2 of complete multibeam bathymetry coverage, ~435 line km of side scan sonar and CHIRP data, 204 line kilometers of magnetometer data, and 194 line kilometers of surface tow boomer profiles. Based on these data, this portion of the Yucatan Shelf consists of flat-lying, hard limestone rock overlain by isolated ribbons of carbonate sand limestone bedrock. This reflector is flat-lying and undisturbed throughout the survey area. Therefore, none of these dissolution pits appear to be underlain by a cenote or sink hole. The NW sector of the survey area exhibits a more complex morphology than the alternating ribbon/bare rock morphology elsewhere, including linear scarps (up to ~1 m relief), deeper pitting (up to ~1 m relief), and sinuous, dendritic channeling (up to ~2 m relief). The geologic origin of these features will require further investigation. Sand drifts are present in this region, but are thinner and cover less area. These observations show the dominant modern sediment formation and transport processes on this starved platform are from large storms and hurricanes that place large regions of the platform at wave base. Remaining observed features were generated during times of lower sea level.

Maturation, fecundity, and intertidal spawning of Pacific sand lance in the northern Gulf of Alaska

Science.gov (United States)

Robards, Martin D.; Piatt, John F.; Rose, G.A.

1999-01-01

Pacific sand lance Ammodytes hexapterus in Kachemak Bay, Alaska, showed no sexual dimorphism in length-to-weight (gonad-free) ratio or length-at-age relationship. Most matured in their second year, males earlier in the season than females, but females (31%) attained a higher gonadosomatic index than males (21%). Sand lance spawned intertidally once each year in late September and October on fine gravel or sandy beaches soon after the seasonal peak in water temperatures. Sand lance in Cook Inlet and Prince William Sound displayed similar maturation schedules. Schools were dominated 2: 1 by males as they approached the intertidal zone at a site where spawning has taken place for decades. Sand lance spawned vigorously in dense formations, leaving scoured pits in beach sediments. Fecundity of females (93–199 mm) was proportional to length, ranging from 1468 to 16 081 ova per female. About half of the overall spawning school fecundity was derived from age group 1 females (55% of the school by number). Spawned eggs were 1·02 mm in diameter, demersal, slightly adhesive, and deposited in the intertidal just below the waterline. Sand lance embryos developed over 67 days through periods of intertidal exposure and sub-freezing air temperatures.

41 CFR 109-1.5104 - Borrowing of personal property.

Science.gov (United States)

2010-07-01

... personal property, consideration shall be given to suitability, condition, value, extent and nature of use... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Borrowing of personal...-INTRODUCTION 1.51-Personal Property Management Standards and Practices § 109-1.5104 Borrowing of personal...

Sub-surface structures and collapse mechanisms of summit pit craters

Science.gov (United States)

Roche, O.; van Wyk de Vries, B.; Druitt, T. H.

2001-01-01

Summit pit craters are found in many types of volcanoes and are generally thought to be the product of collapse into an underpressured reservoir caused by magma withdrawal. We investigate the mechanisms and structures associated with summit pit crater formation by scaled analogue experiments and make comparisons with natural examples. Models use a sand plaster mixture as analogue rock over a cylinder of silicone simulating an underpressured magma reservoir. Experiments are carried out using different roof aspect ratios (roof thickness/roof width) of 0.2-2. They reveal two basic collapse mechanisms, dependant on the roof aspect ratio. One occurs at low aspect ratios (≤1), as illustrated by aspect ratios of 0.2 and 1. Outward dipping reverse faults initiated at the silicone margins propagates through the entire roof thickness and cause subsidence of a coherent block. Collapse along the reverse faults is accommodated by marginal flexure of the block and tension fractures at the surface (aspect ratio of 0.2) or by the creation of inward dipping normal faults delimiting a terrace (aspect ratio of 1). At an aspect ratio of 1, overhanging pit walls are the surface expressions of the reverse faults. Experiments at high aspect ratio (>1.2) reveal a second mechanism. In this case, collapse occurs by stopping, which propagates upwards by a complex pattern of both reverse faults and tension fractures. The initial underground collapse is restricted to a zone above the reservoir and creates a cavity with a stable roof above it. An intermediate mechanism occurs at aspect ratios of 1.1-1.2. In this case, stopping leads to the formation of a cavity with a thin and unstable roof, which collapses suddenly. The newly formed depression then exhibits overhanging walls. Surface morphology and structure of natural examples, such as the summit pit craters at Masaya Volcano, Nicaragua, have many of the features created in the models, indicating that the internal structural geometry of

Oil sands mine planning and waste management using goal programming

Energy Technology Data Exchange (ETDEWEB)

Ben-Awuah, E.; Askari-Nasab, H. [Alberta Univ., Edmonton, AB (Canada). Dept. of Civil and Environmental Engineering; Alberta Univ., Edmonton, AB (Canada). Mining Optimization Laboratory

2010-07-01

A goal programming method was used to plan waste management processes at an oil sands mine. This method requires the decision maker (DM) to set goals. Mine planning is used to determine a block extraction schedule that maximizes net present value (NPV). Due to land restrictions, tailings facilities are sited within the pit area and dykes are used to contain the tailings. Many of the materials used to construct the dykes come from the mining operation. The mine plan scheduled both ore and dyke material concurrently. Dykes were constructed simultaneously as the mine phase advanced. A model was used to classify an oil sands block model into different material types. A mixed integer goal programming (MIGP) method was used to generate a strategic schedule. Block clustering techniques were used to large-scale mine planning projects. The method was used to verify and validate synthetic and real case data related to the cost of mining all material as waste, and the extra cost of mining dyke material. A case study of an oil sands project was used to demonstrate the method. The study showed that the developed model generates a smooth and uniform strategic schedule for large-scale mine planning projects. tabs., figs.

Oil sands mine planning and waste management using goal programming

International Nuclear Information System (INIS)

Ben-Awuah, E.; Askari-Nasab, H.; Alberta Univ., Edmonton, AB

2010-01-01

A goal programming method was used to plan waste management processes at an oil sands mine. This method requires the decision maker (DM) to set goals. Mine planning is used to determine a block extraction schedule that maximizes net present value (NPV). Due to land restrictions, tailings facilities are sited within the pit area and dykes are used to contain the tailings. Many of the materials used to construct the dykes come from the mining operation. The mine plan scheduled both ore and dyke material concurrently. Dykes were constructed simultaneously as the mine phase advanced. A model was used to classify an oil sands block model into different material types. A mixed integer goal programming (MIGP) method was used to generate a strategic schedule. Block clustering techniques were used to large-scale mine planning projects. The method was used to verify and validate synthetic and real case data related to the cost of mining all material as waste, and the extra cost of mining dyke material. A case study of an oil sands project was used to demonstrate the method. The study showed that the developed model generates a smooth and uniform strategic schedule for large-scale mine planning projects. tabs., figs.

Opportunities for CANDU for the Alberta oil sands

International Nuclear Information System (INIS)

Hopwood, J.M.; Bock, D.; Miller, A.; Kuran, S.; Keil, H.; Fiorino, L.; Hau, K.; Zhou, X.; Dunbar, R.B.

2003-01-01

The Alberta oil sands bitumen deposits comprise of one of the largest sources hydrocarbon in the world, and have emerged as the fastest growing, soon to be dominant, source of crude oil in Canada. The oil industry has made great strides in improving the effectiveness of gathering this resource. In particular, alternatives to open-pit mining have been developed which enable in-site recovery of underground deposits with a minimum of environmental disruption. The main challenge that remains is the large quantity of energy needed in the process of extracting the oil and upgrading it to commercial levels. For a typical in-situ extraction project, about 18% of the energy content of the oil produced is used up in the extraction process, while a further 5% is used in generating hydrogen to upgrade the bitumen to synthetic crude oil. Looking ahead, even as improvements in energy use efficiency, (and hydrocarbon use efficiency) counterbalance the increases in hydrocarbon demand from economic growth (particularly in the developing world), Canada and Alberta recognize that the oil sands resource will be needed, and both support the development of this resource in an environmentally responsible way. The large energy requirement for the oil sands extraction process represents a challenge with regard to both environmental impact and security of supply. The use of natural gas, the current energy supply, has impacts in terms of air quality (via NOX and other emissions) and also represents a large greenhouse gas emissions component. As the oil sands industry expands, the availability of natural gas also becomes a concern, as does price and price stability. With this background, the opportunity for nuclear reactors to provide an economical, reliable, virtually zero-emission source of energy for the oil sands becomes very important. Over the last few years, developments in oil sands extraction technology, and developments in CANDU technology through the Advanced CANDU Reactor, (ACR

The development of today's mineable oil sands projects, the key factors influencing economics

International Nuclear Information System (INIS)

Lynn, J.R.

1991-01-01

Many factors influence the perception of economic performance for developing projects. Some of these factors can be controlled by the developer, while some are outside the developer's sphere of influence. Technology selection, management systems, stakeholder involvement, environmental responsiveness and risk management are areas that may be influenced, however interest rates, product prices and currency exchange all have a measurable effect on project economics and are beyond a developer's control. Economic considerations for evaluating mineable oil sand development projects are outlined, focussing on the key factors unique to such developments in general and to the OSLO project in particular. The OSLO project is a proposed $5 billion energy development that entails constructing an open pit oil sands mine and a bitumen extraction facility north of Fort McMurray, Alberta, coupled with a bitumen upgrader in the Redwater area. 7 figs

Influence green sand system by core sand additions

Directory of Open Access Journals (Sweden)

N. Špirutová

2012-01-01

Full Text Available Today, about two thirds of iron alloys casting (especially for graphitizing alloys of iron are produced into green sand systems with usually organically bonded cores. Separation of core sands from the green sand mixture is very difficult, after pouring. The core sand concentration increase due to circulation of green sand mixture in a closed circulation system. Furthermore in some foundries, core sands have been adding to green sand systems as a replacement for new sands. The goal of this contribution is: “How the green sand systems are influenced by core sands?”This effect is considered by determination of selected technological properties and degree of green sand system re-bonding. From the studies, which have been published yet, there is not consistent opinion on influence of core sand dilution on green sand system properties. In order to simulation of the effect of core sands on the technological properties of green sands, there were applied the most common used technologies of cores production, which are based on bonding with phenolic resin. Core sand concentration added to green sand system, was up to 50 %. Influence of core sand dilution on basic properties of green sand systems was determined by evaluation of basic industrial properties: moisture, green compression strength and splitting strength, wet tensile strength, mixture stability against staling and physical-chemistry properties (pH, conductivity, and loss of ignition. Ratio of active betonite by Methylene blue test was also determined.

Baseline Risk Assessment for the F-Area Burning/Rubble Pits and Rubble Pit

Energy Technology Data Exchange (ETDEWEB)

Palmer, E. [Westinghouse Savannah River Company, AIKEN, SC (United States)

1996-03-01

This document provides an overview of the Savannah River Site (SRS) and a description of the F-Area Burning/Rubble Pits (BRPs) and Rubble Pit (RP) unit. It also describes the objectives and scope of the baseline risk assessment (BRA).

Burn Pit Emissions Exposure and Respiratory and Cardiovascular Conditions Among Airborne Hazards and Open Burn Pit Registry Participants.

Science.gov (United States)

Liu, Jason; Lezama, Nicholas; Gasper, Joseph; Kawata, Jennifer; Morley, Sybil; Helmer, Drew; Ciminera, Paul

2016-07-01

The aim of this study was to determine how burn pit emissions exposure is associated with the incidence of respiratory and cardiovascular conditions. We examined the associations between assumed geographic and self-reported burn pit emissions exposure and respiratory and cardiovascular outcomes in participants of the Airborne Hazards and Open Burn Pit Registry. We found significant dose-response associations for higher risk of self-reported emphysema, chronic bronchitis, or chronic obstructive pulmonary disease with increased days of deployment within 2 miles of selected burn pits (P-trend = 0.01) and self-reported burn pit smoke exposure (P-trend = 0.0005). We found associations between burn pit emissions exposure and higher incidence of post-deployment self-reported respiratory and cardiovascular conditions, but these findings should be interpreted with caution because the surrogate measurements of burn pit emissions exposure in this analysis may not reflect individual exposure levels.

Burning/Rubble Pits: Environmental information document

International Nuclear Information System (INIS)

Huber, L.A.; Johnson, W.F.; Marine, I.W.

1987-03-01

The Burning/Rubble Pits, located near each of the major operating areas at the Savannah River Plant (SRP), began collecting burnable waste in 1951. The waste was incinerated monthly. All Burning/Rubble Pits are currently closed except for Burning/Rubble Pit 131-1R, which has not been backfilled but is inactive. No soil cores from the Burning/Rubble Pits have been analyzed. There are four groundwater monitoring wells located around each of the pits, which have been sampled quarterly since 1984. The closure options considered for the Burning/Rubble Pits are waste removal and closure, no waste removal and closure, and no action. Modeling calculations were made to determine the risks to human population for the three postulated closure options. An ecological assessment was conducted to predict the environmental impacts on aquatic and terrestrial biota. The relative costs for each of the closure options were estimated. An evaluation of the environmental impacts from the Burning/Rubble Pits indicates that the relative risks to human health and ecosystems for the postulated closure options are low. The ecological assessment shows that the effects of any closure activities on river water quality and wildlife would be insignificant. The cost estimates show the waste removal and closure option to be the most expensive for all of the pits. 38 refs., 35 figs., 47 tabs

Reclamation of prime farmland following mineral sands mining in Virginia

Energy Technology Data Exchange (ETDEWEB)

Daniels, W.L.; Schroeder, P.D.; Nagle, S.M.; Zelazny, L.W.; Alley, M.M.

1999-07-01

Significant deposits of mineral sands were discovered in Virginia's Upper Coastal Plain in 1989. The Old Hickory deposit is the largest ore body in the state (>2,000 ha) and supports a productive rowcrop agriculture on prime farmlands. field experiments were installed on pilot-scale (25 m x 60 m) mining pits in the late summer of 1995 and replicated on an adjacent undisturbed area. Half of each mining pit was topsoiled (25 cm) while the remaining half was left as either (1) mixed tails/slimes or (2) re-graded subsoil over tails/slimes to simulate various pit closure scenarios. Both non-topsoiled areas received 112 Mg/ha of yard waste compost as a soil building amendment. The entire area was ripped/disked to ameliorate compaction and incorporate lime and fertilizer additions. The experiment was cropped through a wheat/soybeans/corn/cotton rotation over the 1995 to 1998 growing seasons. Taken as a whole, these combined results clearly indicate that mining and reclamation of these prime farmlands will lead to a substantial decrease in rowcrop productivity, at least over the initial years following pit closure and reclamation. For the rotation studied, post-mining productivity was estimated by this experiment to be reduced by 23%, 3%, 27%, and 20% for each crop (wheat/soybeans/corn/cotton) in sequence. For a given crop in a given year, response to topsoiling versus compost addition to the surface varied, and neither treatment appeared superior. Corn and cotton yields on the mined land treatments were reduced despite the application of irrigation. Cotton quality was also adversely affected by the mining reclamation treatments. Results of these controlled experiments are somewhat encouraging. However, the implementation of protocols will be complicated in practice if tailings and slimes cannot be re-blended to generate a reasonably uniform final reclaimed surface.

CRSMP Potential Offshore Borrow Sites 2012

Data.gov (United States)

California Natural Resource Agency — Offshore borrow sites as identified originally in the California Shoreline Database compiled by Noble Consultants (Jon Moore). Later updates to the dataset by the...

7 CFR 1951.262 - Farm Credit Programs-graduation of borrowers.

Science.gov (United States)

2010-01-01

... determine their ability to graduate. (f) Sending prospectus information to lenders. (1) The Agency will... Needs and Graduation of Borrowers § 1951.262 Farm Credit Programs—graduation of borrowers. (a)-(d... must submit a year-end balance sheet, actual financial performance information for the most recent year...

Foreign currency borrowing by small firms in the transition economies

NARCIS (Netherlands)

Brown, M.; Ongena, S.; Yesin, P.

2011-01-01

We examine the firm- and country-level determinants of foreign currency borrowing by small firms, using information on the most recent loan extended to 3101 firms in 25 transition countries between 2002 and 2005. Our results suggest that foreign currency borrowing is much stronger related to

7 CFR 1717.656 - Exemption of certain borrowers from controls.

Science.gov (United States)

2010-01-01

... of the government with respect to loan security and/or repayment. (Such borrower is eligible to ask... UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE POST-LOAN POLICIES AND PROCEDURES COMMON TO INSURED AND GUARANTEED ELECTRIC LOANS Investments, Loans, and Guarantees by Electric Borrowers § 1717.656 Exemption of...

Parturition pit: the bony imprint of vaginal birth

International Nuclear Information System (INIS)

McArthur, Tatum A.; Meyer, Isuzu; Jackson, Bradford; Pitt, Michael J.; Larrison, Matthew C.

2016-01-01

To retrospectively evaluate for pits along the dorsum of the pubic body in females and compare the presence/absence of these pits to vaginal birth data. We retrospectively reviewed females with vaginal birth data who underwent pelvic CT. The presence of pits along the dorsum of the pubic body, pit grade (0 = not present; 1 = faintly imperceptible; 2 = present; 3 = prominent), and the presence of osteitis condensans ilii, preauricular sulcus, and sacroiliac joint vacuum phenomenon were assessed on imaging. Musculoskeletal radiologists who were blinded to the birth data evaluated the CTs. 48 males were also evaluated for the presence of pits. 482 female patients underwent CT pelvis and 171 were excluded due to lack of vaginal birth data. Of the 311 study patients, 262 had prior vaginal birth(s) and 194 had pits on CT. Only 7 of the 49 patients without prior vaginal birth had pits. There was a statistically significant association between vaginal birth and presence of pits (p < 0.0001). Patients with more prominent pits (grades 2/3) had a greater number of vaginal births. As vaginal deliveries increased, the odds of having parturition pits greatly increased, adjusting for age and race at CT (p < 0.0001). No males had pits. Our study indicates that parturition pits are associated with prior vaginal birth and should be considered a characteristic of the female pelvis. The lytic appearance of prominent pits on imaging can simulate disease and create a diagnostic dilemma for interpreting radiologists. (orig.)

Post-pit optimization strategic alignment

OpenAIRE

Breed, M.F.; van Heerden, D.

2016-01-01

Successful development of projects or life-of-mine strategies requires an understanding of the relative sensitivity of value drivers such as grade, tonnage, energy costs, direct operational costs, and recoveries. For example, the results could vary significantly depending on the grade strategy, given a specific orebody amenable to open pitting. Pit optimization is a very powerful tool widely used in the industry to determine the pit shell with the most attractive value potential. Based on the...

Influence of Pitting Corrosion on Fatigue and Corrosion Fatigue of Ship and Offshore Structures, Part II: Load - Pit - Crack Interaction

Directory of Open Access Journals (Sweden)

Jakubowski Marek

2015-09-01

Full Text Available In the paper has been discussed influence of stresses on general corrosion rate and corrosion pit nucleation rate and growth , whose presence has been questioned by some authors but accepted by most of them. Influence of roughness of pit walls on fatigue life of a plate suffering pit corrosion and presence of the so called „ non-damaging” pits which never lead to initiation of fatigue crack, has been presented. Possibility of prediction of pit-to-crack transition moment by two different ways, i.e. considering a pit a stress concentrator or an equivalent crack, has been analyzed. Also, influence of statistical distribution of depth of corrosion pits as well as anticorrosion protection on fatigue and corrosion fatigue has been described.

pitting corrosion susceptibility pitting corrosion susceptibility of aisi

African Journals Online (AJOL)

eobe

2DEPARTMENT OF MECHANICAL ENGINEERING, UNIVERSITY OF BENIN, BENIN- CITY, EDO STATE, NIGERIA. E-mail addresses: ... fluids and aggressive chemicals. Pitting corrosion ... the kitchen, food manufacturing and dispensing and.

FACTORS INFLUENCING SMALLHOLDERS' TRANSACTION COST OF BORROWING FROM THE NIGERIAN AGRICULTURAL AND COOPERATIVE BANK

OpenAIRE

Olomola, A.S.

1992-01-01

In Nigeria, small-scale farmers are reluctant to borrow from formal institutions because of high transaction costs. This paper examines the components and determinants of borrowing transaction costs and argues that unless the loan administrative strategies are simplified and channels of loan delivery diversified, farmers would continue to find it difficult to use formal loans. Borrowing transaction costs are defined as the administrative expenses and transportation cost incurred by borrowers ...

7 CFR 1710.303 - Power cost studies-power supply borrowers.

Science.gov (United States)

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Power cost studies-power supply borrowers. 1710.303... AND GUARANTEES Long-Range Financial Forecasts § 1710.303 Power cost studies—power supply borrowers. (a... facilities shall be supported by a power cost study to demonstrate that the proposed generation and...

Chemicals, metals, and pesticide pits waste unit low induction number electromagnetic survey

Energy Technology Data Exchange (ETDEWEB)

Cumbest, R.J.; Mohon, D.

1995-06-01

An electromagnetic survey was conducted at the Chemicals, Metals, and Pesticide Waste Unit to identify any buried metallic objects that may be present in the materials used to fill and cover the pits after removal of pit debris. The survey was conducted with a Geonics EM-31 Terrain Conductivity Meter along north - south oriented traverses with 5-ft station intervals to produce a 5-ft by 5-ft square grid node pattern. Both conductivity and in-phase components were measured at each station for vertical dipole orientation with the common axis of the dipoles in the north - south and east - west orientations. The conductivity data clearly show elevated conductivities (2.1 to 7.0 mS/m) associated with the material over the pits, as compared with the surrounding area that is characterized by lower conductivities (1 to 2 mS/m). This is probably the result of the higher clay content of the fill material relative to the surrounding area, which has a higher sand to clay ratio and the presence of a plastic cover beneath the fill that has probably trapped water. Many metal objects are present in the survey area including manhole covers, monitoring well heads, metal, signs, drain culverts, abandoned wells, and BP waste unit marker balls. AU of these exhibit associated conductivity and in-phase anomalies of various magnitude. In addition to these anomalies that can be definitely associated with surface sources, conductivity and in-phase anomalies are also present with no obvious surface source. These anomalies are probably indicative of subsurface buried metallic objects. A high concentration of these objects appears to be present in the southwest corner of the survey area.

Oxygen pitting failure of a bagasse boiler tube

CSIR Research Space (South Africa)

Heyes, AM

2001-04-01

Full Text Available Examination of a failed roof tube from a bagasse boiler showed transverse through-cracks and extensive pitting. The pitting was typically oxygen induced pitting and numerous fatigue cracks had started within these pits. It is highly probable...

Accountability Quality Shuffler Measurements on Pits

International Nuclear Information System (INIS)

Rinard, P.M.

2000-01-01

Pits have generally been treated as accountable units that are intact if merely present and they are excluded from the more demanding nondestructive assay requirements. As pits begin to flow into disposition streams, there may be more incentive to measure the masses of their fissile components for accountability purposes. This Department of Energy Office of Safeguards and Security (OSS) Lifecycle Project has explored some ways in which such measurements may be done successfully. The active neutron instrument called a shuffler has been used to measure a variety of actual pits, and a calculational technique has been developed to accurately predict such count rates. Passive multiplicity counting has previously been applied to pits for determining their plutonium contents. This combination of measurement and calculational techniques provide powerful and accurate tools for determining the fissile contents of pits with the quality needed for accountability purposes

Scared away? Discouraged borrowers and Capital market information

DEFF Research Database (Denmark)

Christensen, Jesper Lindgaard; Hain, Daniel S.

2014-01-01

of discouraged borrowers. Implications Implications entail missed opportunities for firms, which in turn is likely to have deterrent effects on overall investments and economic growth. Financial institutions will miss out on business opportunities but will also have difficulties in fine-tuning their credit......We do the first study on discouraged borrowers in Denmark to firstly investigate the extent of this phenome-non in Denmark. Secondly, we test if characteristics of firms (age, size, innovativeness, industry) impact their likelihood of being discouraged from entering the capital markets. Thirdly...

Borrowed Capital as Risk Factor for Large Construction Companies in Russia

Science.gov (United States)

Guzikova, L.; Plotnikova, E.; Zubareva, M.

2017-11-01

The paper investigates the features of the formation of the capital structure of large construction companies from the standpoint of the financial risks and opportunities for companies’ development. The authors compare the opportunities and risks linked with the use of the own and borrowed capital, analyze the capital structure of large Russian construction companies, identify factors affecting the capital structure and determining the ratio of own and borrowed sources of financing. In the paper the hypothesis is considered that companies use larger volumes of borrowed capital by means of their assets increase.

An introduction to conservation and reclamation at Alberta's mineable oil sands

Energy Technology Data Exchange (ETDEWEB)

Richens, T. [Alberta Environment, Edmonton, AB (Canada)

2009-07-01

This paper presented a balanced view of the conservation and reclamation issues and challenges facing oil sands development in Alberta. Bitumen is recovered by truck and shovel in the shallow oil sands of the Athabasca region. The deeper deposits in the Athabasca, Peace River and Cold Lake regions are accessed primarily using a system of horizontal wells and steam to extract the bitumen from the sand and pump it to the surface. Individual in-situ operations have a smaller environmental impact than mines, and do not produce tailings ponds. However, the footprint of in-situ facilities will accumulate over time because of the potential for extensive future development. The key issues facing conservation and reclamation in the mineable oil sands were discussed. Summary statistics on land disturbed and reclaimed in the region were also provided. The challenges facing reclamation activities include long timeframes; large scale, regional planning and integration; competing land use goals; revegetation; byproduct management; and tailings and process-affected water. Multi-stakeholder forums have proven to be the key to the progression of monitoring, research and development and the sharing of knowledge and information. Frameworks have been developed for the assessment of pre-disturbed and reclaimed soil capability specific to the oil sands region. Additional resources are also available, such as guidelines for the reclamation of terrestrial and wetland habitats that represent the best management practices for reclamation research in revegetation, soil salvage, stockpiling and placement, tailings reclamation, end pit lakes, wetlands and biodiversity. 16 refs., 1 fig.

Advanced characterisation of organic matter in oil sands and tailings sands used for land reclamation by Fourier transform-ion cyclotron resonance-mass spectrometry (FT-ICR-MS)

Science.gov (United States)

Noah, M.; Vieth-Hillebrand, A.; Wilkes, H.

2012-04-01

The Athabasca region of northern Alberta, Canada, is home to deposits of oil sands containing vast amounts (~ 173 billion barrels) of heavily biodegraded petroleum. Oil sands are recovered by surface mining or by in situ steam injection. The extraction of bitumen from oil sands by caustic hot water processing results in large volumes of fluid tailings, which are stored in on-site settling basins. There the tailings undergo a compaction and dewatering process, producing a slowly densifying suspension. The released water is recycled for extraction. The fine tailings will be reclaimed as either dry or wet landscapes. [1] To produce 1 barrel of crude oil, 2 tons of oil sand and 2 - 3 tons of water (including recycled water) are required. [2] Open pit mining and the extraction of the bitumen from the oil sands create large and intense disturbances of different landscapes. The area currently disturbed by mining operations covers about 530 km2 and the area of tailing ponds surpasses 130 km2. An issue of increasing importance is the land remediation and reclamation of oil sand areas in Canada and the reconstruction of these disturbed landscapes back to working ecosystems similar to those existing prior to mining operations. An important issue in this context is the identification of oil sand-derived organic compounds in the tailings, their environmental behaviour and the resulting chances and limitations with respect to land reclamation. Furthermore the biodegradation processes that occur in the tailings and that could lead to a decrease in hazardous organic compounds are important challenges, which need to be investigated. This presentation will give a detailed overview of our compositional and quantitative characterisation of the organic matter in oil sand, unprocessed and processed mature fine tailings samples as well as in tailings sands used as part of land reclamation. The analytical characterisation is based on the extraction of the soluble organic matter, its

Demonstration of In-Situ Stabilization of Buried Waste at Pit G-11 at the Brookhaven National laboratory Glass Pits Disposal Site

International Nuclear Information System (INIS)

Dwyer, B.P.; Gilbert, J.; Heiser, J.

1999-01-01

In 1989 BNL was added to the EPAs National Priorities List. The site is divided into seven operable units (OU). OU-I includes the former landfill area. The field task site is noted as the AOC 2C Glass Holes location. Beginning in the 1960s and continuing into the 1980s, BNL disposed of laboratory waste (glassware, chemicals and animal carcasses) in numerous shallow pits. The drivers for remediating the pits are; historical records that indicate hazardous materials may have been disposed of in the pits; ground water contamination down gradient of the pits; a test excavation of one of the glass holes that unearthed laboratory glass bottles with unidentified liquids still contained; and the fact that BNL rests atop an EPA designated sole-source aquifer. The specific site chosen for this demonstration was pit G-11. The requirements that lead to choosing this pit were; a well characterized pit and a relatively isolated pit where our construction operations would not impact on adjacent pits. The glass holes area, including pit G-11, was comprehensively surveyed using a suite of geophysical techniques (e.g., EM-31, EM-61, GPR). Prior to stabilizing the waste form a subsurface barrier was constructed to contain the entire waste pit. The pit contents were then stabilized using a cement grout applied via jet grouting. The stabilization was performed to make removal of the waste from the pit easier and safer in terms of worker exposure. The grouting process would mix and masticate the waste and grout and form a single monolithic waste form. This large monolith would then be subdivided into smaller 4 foot by 4 foot by 10-12 foot block using a demolition grout. The smaller blocks would then be easily removed from the site and disposed of in a CERCLA waste site

Experimental Stress Analysis at Railway Inspection Pit

Directory of Open Access Journals (Sweden)

Nicuşor Laurentiu Zaharia

2008-10-01

Full Text Available Railway inspection pits are used in railway halls. The purpose of inspection pits is to allow the working under the vehicle. Inspection pits can be found in locomotive depots, factories etc. The new design for a inspection pit in a railway hall involve tests in purpose of homologations the railway infrastructure. Before the homologation committee meeting, tests are made; after the test, a testing report is made which it will be part at homologation documents.

7 CFR 1781.21 - Borrower accounting methods, management, reporting, and audits.

Science.gov (United States)

2010-01-01

... 7 Agriculture 12 2010-01-01 2010-01-01 false Borrower accounting methods, management, reporting... DEVELOPMENT (RCD) LOANS AND WATERSHED (WS) LOANS AND ADVANCES § 1781.21 Borrower accounting methods, management, reporting, and audits. These activities will be handled in accordance with the provisions of...

7 CFR 1942.128 - Borrower accounting methods, management reports and audits.

Science.gov (United States)

2010-01-01

... 7 Agriculture 13 2010-01-01 2009-01-01 true Borrower accounting methods, management reports and audits. 1942.128 Section 1942.128 Agriculture Regulations of the Department of Agriculture (Continued... Rescue and Other Small Community Facilities Projects § 1942.128 Borrower accounting methods, management...

Pits on Ascraeus

Science.gov (United States)

2005-01-01

24 September 2005 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows collapse pits and troughs on the lower northeast flank of the giant martian volcano, Ascraeus Mons. Layers of volcanic rock are evident in some of the pit and valley walls, and boulders the size of houses and trucks that were liberated from these walls by gravity can be seen on the floors of the depressions. Location near: 13.6oN, 102.6oW Image width: width: 3 km (1.9 mi) Illumination from: lower left Season: Northern Autumn

Compromised metamorphosis and thyroid hormone changes in wood frogs (Lithobates sylvaticus) raised on reclaimed wetlands on the Athabasca oil sands

International Nuclear Information System (INIS)

Hersikorn, Blair D.; Smits, Judit E.G.

2011-01-01

The wet landscape approach to oil sands tailings reclamation in the Athabasca Oil Sands region involves creating wetlands from fluid tailings in mined-out pits. We measured time to metamorphosis, thyroid hormone status, and detoxification enzyme (EROD) induction in Wood frog (Lithobates sylvaticus) tadpoles raised on reclaimed oil sands wetlands of different ages [young (≤7 yr) vs. old (>7 yr)] and compared data with tadpoles raised on reference (control) wetlands. Metamorphosis was delayed or never occurred in tadpoles raised in young tailings; those exposed to older tailings developed similarly to those in reference wetlands. Thyroid hormone disruption likely played an important role in the metamorphosis delay as the T3:T4 ratio was lowest in tadpoles raised in young, tailings-affected wetlands. Our findings suggest tailings wetlands become less toxic with age, and that these amphibians will be able to complete their life cycle in tailing wetlands that have sufficiently detoxified with age. - This work provides guidance for reclamation of oil sands tailings and shows the usefulness of frogs and caging studies in environmental toxicology.

Compromised metamorphosis and thyroid hormone changes in wood frogs (Lithobates sylvaticus) raised on reclaimed wetlands on the Athabasca oil sands

Energy Technology Data Exchange (ETDEWEB)

Hersikorn, Blair D., E-mail: blair.hersikorn@usask.c [Toxicology Centre, University of Saskatchewan, 44 Campus Drive, Saskatoon, Saskatchewan, S7N 5B3 (Canada); Smits, Judit E.G., E-mail: judit.smits@ucalgary.c [Faculty of Veterinary Medicine, University of Calgary, 3280 Hospital Drive NW, Calgary, Alberta, T2N 4Z6 (Canada)

2011-02-15

The wet landscape approach to oil sands tailings reclamation in the Athabasca Oil Sands region involves creating wetlands from fluid tailings in mined-out pits. We measured time to metamorphosis, thyroid hormone status, and detoxification enzyme (EROD) induction in Wood frog (Lithobates sylvaticus) tadpoles raised on reclaimed oil sands wetlands of different ages [young ({<=}7 yr) vs. old (>7 yr)] and compared data with tadpoles raised on reference (control) wetlands. Metamorphosis was delayed or never occurred in tadpoles raised in young tailings; those exposed to older tailings developed similarly to those in reference wetlands. Thyroid hormone disruption likely played an important role in the metamorphosis delay as the T3:T4 ratio was lowest in tadpoles raised in young, tailings-affected wetlands. Our findings suggest tailings wetlands become less toxic with age, and that these amphibians will be able to complete their life cycle in tailing wetlands that have sufficiently detoxified with age. - This work provides guidance for reclamation of oil sands tailings and shows the usefulness of frogs and caging studies in environmental toxicology.

The Treatment of Borrowed Nouns in Isichazamazwi SesiNdebele and Isichazamazwi SezoMculo

Directory of Open Access Journals (Sweden)

Eventhough Ndlovu

2011-10-01

Full Text Available Abstract: This article focuses on the lemmatisation of vowel-commencing borrowed nouns and the allo-cation of borrowed nouns to noun class prefixes in Isichazamazwi SesiNdebele, the first monolingual general-purpose Ndebele dictionary, and Isichazamazwi SezoMculo, the first specialised Ndebele dictionary of musical terms. It adopts a comparative approach, also highlighting the controversies surrounding the status of the initial vowel of the prefix or the pre-prefix in Ndebele and other Nguni languages. It further looks at the challenges and limitations of lemmatising the noun using either the initial vowel of the prefix or the initial letter of the noun stem. It is found that there are some inconsistencies in the lemmatisation of vowel-com-mencing borrowed nouns and the allocation of borrowed nouns to noun class prefixes in the two dictionar-ies. These inconsistencies impact negatively on the standardisation and treatment of borrowed nouns.

Environment - Borrow Area for Temporary Levee

Data.gov (United States)

Army Corps of Engineers, Department of the Army, Department of Defense — This data represents the location of a borrow site for construction materials used in temporary levee building during flood events. The footprint of these areas have...

22 CFR 1104.2 - Definitions.

Science.gov (United States)

2010-04-01

..., hide, feathers, pigments, and flaked, ground, or pecked stone); (iv) By-products, waste products, or... fields, bedrock mortars or grinding surfaces, rock alignments, cairns, trails, borrow pits, cooking pits...

18 CFR 1312.3 - Definitions.

Science.gov (United States)

2010-04-01

..., hide, feathers, pigments, and flaked, ground, or pecked stone); (iv) By-products, waste products, or..., bedrock mortars or grinding surfaces, rock alignments, cairns, trails, borrow pits, cooking pits, refuse...

IFRS and US GAAP convergence in the area of borrowing costs

Directory of Open Access Journals (Sweden)

Hana Bohušová

2009-01-01

Full Text Available An agreement from Norwalk was issued in September 2002 on the basis of negotiations of Financial Accounting Standards Board (FASB a International Accounting Standards Board (IASB for the elimination of restrictions in the form of two different systems of financial reporting. The aim is to ensure absolute compatibility of existing U.S. GAAP and IFRS and the coordination of work programs in the future. Document Memorandum of Understanding was issued in 2006 in the frame of ongoing process of convergence, in which the FASB and IASB confirm their intention to create high-quality and global financial reporting standards. In this document there are specified areas, which would lead to convergence of procedures.Borrowing costs have been one from the fields, which was the subject of convergence works. U.S. GAAP dictated capitalization of borrowing costs incurred in connection with the acquisition of qualifying assets, while the IAS/IFRS leaved the decision on accounting entities, how it recognize and record borrowing costs incurred in connection with the acquisition of the assets.In the beginning, the method of analysis and description is used to identify and describe the basic difference of both systems, which had existed before the initiation of convergence within the frame of “Borrowing Costs” project. The above mentioned primary analysis has served as the basis for the further comparative analysis and synthesis.The paper further presents comparative analysis of two basic methodical approaches towards the borrowing costs reporting incurred in relation to the acquisition of the qualifying assets, which was possible to apply until 31st Dec 2008 under IFRS system.The comparative analysis is based on empirical company data. The subjects are mainly the differences in the indicators, which are used for the evaluation of the company financial situation. According (Suvova, 1999, mainly the indicators of vertical analysis of property and capital structure

7 CFR 3560.405 - Borrower organizational structure or ownership interest changes.

Science.gov (United States)

2010-01-01

... Servicing § 3560.405 Borrower organizational structure or ownership interest changes. (a) General. The requirements of this section apply to changes in a borrower entity's organizational structure or to a change in... organizational change. The request must document that the proposed changes will not adversely affect the program...

The Influence of Radiation on Pit Solution Chemistry as it Pertains to the Transition from Metastable to Stable Pitting in Steels

International Nuclear Information System (INIS)

Galuszka-Muga, Barbara; Muga, Luis M.

2006-01-01

Previous work relevant to current efforts is summarized. A description of an improved version of a new electrochemical probe, the ArtPit, is given. The distinct feature of the probe for investigating metastable pitting of carbon steels is specified and compared to other approaches. The electrochemical response of the ArtPit under the gamma irradiation and elevated temperature conditions that occur at high level waste (HLW) storage tanks is presented. In particular, the Tafel slope determinations and chemical analyses of the ArtPit confined volume electrolyte are described. Based on results a possible approach for reducing the corrosion rate of HLW tank walls is suggested. Additional statistical analysis of the occurrence of short duration (passivated pits) and long term (stable pitting) electrochemical pulses (current surges) during exposure confirm that radiation enhances the occurrence of both more and smaller sized pits due to increased likelihood of repassivation

7 CFR 1944.425 - Handling and accounting for borrower loan funds.

Science.gov (United States)

2010-01-01

... 7 Agriculture 13 2010-01-01 2009-01-01 true Handling and accounting for borrower loan funds. 1944... Grants § 1944.425 Handling and accounting for borrower loan funds. Grantees will be required to...HA or its successor agency under Public Law 103-354's non-discrimination policies in receiving...

Computer simulation of pitting potential measurements

International Nuclear Information System (INIS)

Laycock, N.J.; Noh, J.S.; White, S.P.; Krouse, D.P.

2005-01-01

A deterministic model for the growth of single pits in stainless steel has been combined with a purely stochastic model of pit nucleation. Monte-Carlo simulations have been used to compare the predictions of this model with potentiodynamic experimental measurements of the pitting potential. The quantitative agreement between model and experiment is reasonable for both 304 and 316 stainless steel, and the effects of varying surface roughness, solution chloride concentration and potential sweep rate have been considered

Ownership Networks Effects on Secured Borrowing

NARCIS (Netherlands)

Martinez, Constanza; Cizek, Pavel; Leon Rincon, Carlos

2018-01-01

The secured borrowing based on sell/buy-backs agreements is studied, specifically considering both: quantity and price. The empirical evidence presented in this paper suggests that, after controlling for specific individual characteristics, group-specific effects (defined by belonging or not to a

PIT 9 Project: A private sector initiative

International Nuclear Information System (INIS)

Macdonald, D.W.; Hughes, F.P.; Burton, B.N.

1993-01-01

The Pit 9 Comprehensive Demonstration is intended to demonstrate a cost-effective approach to remediate an Idaho National Engineering Lab. (INEL) waste disposal pit through a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) Interim Action. The remediation will include additional requirements, if needed, to provide high confidence that only minor additional work would be necessary to accomplish the final closure as part of the overall final closure strategy for the INEL's Subsurface Disposal Area (SDA). Pit 9 is an inactive waste disposal pit located in the northeastern corner of the SDA at the INEL's Radioactive Waste Management Complex (RWMC). It covers approximately 1 acre. The waste within Pit 9 is primarily transuranic waste generated at the Rocky Flats Plant and additional wastes, both hazardous and low-level radioactive, from generators at the INEL

Analysis of BY-106 pump pit cover plate

International Nuclear Information System (INIS)

Coverdell, B.L.

1994-01-01

A new cover for the pump pit of Tank 241-BY-106 has been designed to allow the rotary core exhauster to be hooked up without requiring pit entry, riser modification, or equipment removal. The new pit cover is necessary to allow installation of two risers for reducing exposure, contamination, and waste. Computer analysis indicates that the safety margin of the pit cover plate with two risers is adequate. The computer stress model and input files are attached. The pit cover plate is a replacement for an existing plate; therefore seismic and wind loads were considered for the plate only

34 CFR 674.49 - Bankruptcy of borrower.

Science.gov (United States)

2010-07-01

..., DEPARTMENT OF EDUCATION FEDERAL PERKINS LOAN PROGRAM Due Diligence § 674.49 Bankruptcy of borrower. (a... determination of dischargeability. (1) The institution must use due diligence and may assert any defense...

Structures of Bordered Pits Potentially Contributing to Isolation of a Refilled Vessel from Negative Xylem Pressure in Stems of Morus australis Poir.: Testing of the Pit Membrane Osmosis and Pit Valve Hypotheses.

Science.gov (United States)

Ooeda, Hiroki; Terashima, Ichiro; Taneda, Haruhiko

2017-02-01

Two hypotheses have been proposed to explain the mechanism preventing the refilling vessel water from being drained to the neighboring functional vessels under negative pressure. The pit membrane osmosis hypothesis proposes that the xylem parenchyma cells release polysaccharides that are impermeable to the intervessel pit membranes into the refilling vessel; this osmotically counteracts the negative pressure, thereby allowing the vessel to refill. The pit valve hypothesis proposes that gas trapped within intervessel bordered pits isolates the refilling vessel water from the surrounding functional vessels. Here, using the single-vessel method, we assessed these hypotheses in shoots of mulberry (Morus australis Poir.). First, we confirmed the occurrence of xylem refilling under negative pressure in the potted mulberry saplings. To examine the pit membrane osmosis hypothesis, we estimated the semi-permeability of pit membranes for molecules of various sizes and found that the pit membranes were not semi-permeable to polyethylene glycol of molecular mass osmosis mechanism in mulberry would be unrealistically large. © The Author 2016. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

12 CFR 617.7105 - When must a qualified lender disclose the effective interest rate to a borrower?

Science.gov (United States)

2010-01-01

... effective interest rate to a borrower? 617.7105 Section 617.7105 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM BORROWER RIGHTS Disclosure of Effective Interest Rates § 617.7105 When must a qualified lender disclose the effective interest rate to a borrower? (a) Disclosure to prospective borrowers...

Mississippi Coastal Improvements Program; Evaluation of Barrier Island Restoration Efforts

Science.gov (United States)

2013-09-01

451   ERDC TR-13-12 xx Figure G-14. Alternative #1 Restored conditions for Storm #2; Template C; Without borrow pits. ......... 451   Figure G-15...0.02831685 cubic meters cubic yards 0.7645549 cubic meters degrees Fahrenheit (F-32)/1.8 degrees Celsius feet 0.3048 meters inches 0.0254 meters...conditions for Storm #2; Template A; Without borrow pits. ERDC TR-13-12 451 Figure G-13. Alternative #1 Restored conditions for Storm #2; Template B

13 CFR 120.910 - Borrower contributions.

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Borrower contributions. 120.910 Section 120.910 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Development... percent, if the Project involves the acquisition, construction, conversion, or expansion of a limited or...

25 CFR 103.26 - What must the borrower supply the lender in its loan application?

Science.gov (United States)

2010-04-01

... cash flow statements; (i) A detailed list of all proposed collateral for the loan, including asset... amount and offer the proposed loan collateral; and (m) If the borrower is a business entity, resolutions... permitting the borrower to borrow the loan amount and offer the proposed loan collateral. ...

"Subnational Borrowing in Japan : from 'Implicit Guarantee' to Market Discipline and Fiscal Rule"

OpenAIRE

Nobuki Mochida

2008-01-01

In many countries, local borrowing is an important source for long-term development projects such as roads, bridges, and waterworks. Local borrowing for such projects is justified on the ground that benefit of these projects often last decades and the cost of these projects should be borne by future tax payers. However, there are serious concerns with issuance of local bonds by decentralized local governments. Local governments in Japan would not default on their borrowing because of such "im...

Pit Viper strikes at the Hanford site. Pit maintenance using robotics at the Hanford Tank Farms

International Nuclear Information System (INIS)

Roeder-Smith, Lynne

2002-01-01

The Pit Viper--a remote operations waste retrieval system--was developed to replace manual operations in the valve pits of waste storage tanks at the Hanford Site. The system consists of a typical industrial backhoe fitted with a robotic manipulator arm and is operated remotely from a control trailer located outside of the tank farm. Cameras mounted to the arm and within the containment tent allow the operator to view the entire pit area and operate the system using a joystick. The arm's gripper can grasp a variety of tools that allow personnel to perform cleaning, debris removal, and concrete repair tasks--a more efficient and less dose-intensive process than the previous 'long-pole' method. The project team overcame a variety of obstacles during development and testing of the Pit Viper system, and deployment occurred in Hanford Tank C-104 in December 2001

Environmental Impacts of Sand Exploitation. Analysis of Sand Market

Directory of Open Access Journals (Sweden)

Marius Dan Gavriletea

2017-06-01

Full Text Available Sand is an indispensable natural resource for any society. Despite society’s increasing dependence on sand, there are major challenges that this industry needs to deal with: limited sand resources, illegal mining, and environmental impact of sand mining. The purpose of this paper is twofold: to present an overview of the sand market, highlighting the main trends and actors for production, export and import, and to review the main environmental impacts associated with sand exploitation process. Based on these findings, we recommend different measures to be followed to reduce negative impacts. Sand mining should be done in a way that limits environmental damage during exploitation and restores the land after mining operations are completed.

Markov Chain Models for the Stochastic Modeling of Pitting Corrosion

Directory of Open Access Journals (Sweden)

A. Valor

2013-01-01

Full Text Available The stochastic nature of pitting corrosion of metallic structures has been widely recognized. It is assumed that this kind of deterioration retains no memory of the past, so only the current state of the damage influences its future development. This characteristic allows pitting corrosion to be categorized as a Markov process. In this paper, two different models of pitting corrosion, developed using Markov chains, are presented. Firstly, a continuous-time, nonhomogeneous linear growth (pure birth Markov process is used to model external pitting corrosion in underground pipelines. A closed-form solution of the system of Kolmogorov's forward equations is used to describe the transition probability function in a discrete pit depth space. The transition probability function is identified by correlating the stochastic pit depth mean with the empirical deterministic mean. In the second model, the distribution of maximum pit depths in a pitting experiment is successfully modeled after the combination of two stochastic processes: pit initiation and pit growth. Pit generation is modeled as a nonhomogeneous Poisson process, in which induction time is simulated as the realization of a Weibull process. Pit growth is simulated using a nonhomogeneous Markov process. An analytical solution of Kolmogorov's system of equations is also found for the transition probabilities from the first Markov state. Extreme value statistics is employed to find the distribution of maximum pit depths.

Ecohydrology applications to ecosystem reconstruction after oil-sand mining

Science.gov (United States)

Mendoza, Carl; Devito, Kevin

2014-05-01

Oil-sand deposits in northeast Alberta, Canada comprise some of the world's largest oil reserves. Open-pit mining of these resources leads to waste-rock piles, tailings ponds and open pits that must be reclaimed to "equivalent landscape capability", with viable forests and wetlands, using only native vegetation. Understanding ecohydrological processes in natural systems is critical for designing the necessary landforms and landscapes. A challenge is the cold, sub-humid climate, with highly variable precipitation. Furthermore, there are competing demands, needs or uses for water, in both quantity and quality, for reclamation and sustainability of forestlands, wetlands and end-pit lakes. On average there is a potential water deficit in the region, yet wetlands cover half of the undisturbed environment. Water budget analyses demonstrate that, although somewhat unpredictable and uncontrollable, the magnitude and timing of water delivery largely control water storage and conservation within the landscape. The opportunity is to design and manipulate these reconstructed landscapes so that water is stored and conserved, and water quality is naturally managed. Heterogeneous geologic materials can be arranged and layered, and landforms sculpted, to minimize runoff, enhance infiltration, and promote surface and subsurface storage. Similarly, discharge of poor quality water can be minimized or focused. And, appropriate vegetation choices are necessary to conserve water on the landscape. To achieve these ends, careful attention must be paid to the entire water budget, the variability in its components, interconnections between hydrologic units, in both space and time, and coupled vegetation processes. To date our knowledge is guided primarily by natural analogues. To move forward, it is apparent that numerous priorities and constraints, which are potentially competing, must be addressed. These include geotechnical and operational requirements, material limitations or excesses

Brazilian Credit Union Member Groups: Borrower-dominated, Saver-dominated or Neutral Behavior?

Directory of Open Access Journals (Sweden)

Valéria Gama Fully Bressan

2013-01-01

Full Text Available Theoretical models concerning Credit Unions (CUs suggest that the type of CU domination determines the way it allocates the monetary value it generates. A borrower- (saver- dominated CU benefits borrower (saver members at the expenses of saver (borrower members, and a neutral CU equally benefits its member groups.This paper applies direct measure of monetary benefits to each member group (Patin & McNiel, 1991a to testfor the existence of dominated behavior in Brazilian CUs, and is the first to apply panel data regressions to identify the determinants of CUs behavior. We use a unique panel data with 40,664 observations taken from 533 CUs affiliated with the largest Brazilian cooperative network. Results indicate Brazilian CUs are dominated by borrowers, but behave close to neutrality. Panel regression estimates show that common or multiple bond type,size and overdue loans of a CU have no effect on its behavior, the greater the total amount of loans over social capital and adjusted equity over total assets are the more likely a CU is borrower dominated, and the greater the age and current operational expenses over total asset of a CU are the more likely a CU is saver dominated.

W-12 valve pit decontamination demonstration

International Nuclear Information System (INIS)

Benson, C.E.; Parfitt, J.E.; Patton, B.D.

1995-12-01

Waste tank W-12 is a tank in the ORNL Low-Level Liquid Waste (LLLW) system that collected waste from Building 3525. Because of a leaking flange in the discharge line from W-12 to the evaporator service tank (W-22) and continual inleakage into the tank from an unknown source, W-12 was removed from service to comply with the Federal Facilities Agreement requirement. The initial response was to decontaminate the valve pit between tank W-12 and the evaporator service tank (W-22) to determine if personnel could enter the pit to attempt repair of the leaking flange. Preventing the spread of radioactive contamination from the pit to the environment and to other waste systems was of concern during the decontamination. The drain in the pit goes to the process waste system; therefore, if high-level liquid waste were generated during decontamination activities, it would have to be removed from the pit by means other than the available liquid waste connection. Remote decontamination of W-12 was conducted using the General Mills manipulator bridge and telescoping trolley and REMOTEC RM-10 manipulator. The initial objective of repairing the leaking flange was not conducted because of the repair uncertainty and the unknown tank inleakage. Rather, new piping was installed to empty the W-12 tank that would bypass the valve pit and eliminate the need to repair the flange. The radiological surveys indicated that a substantial decontamination factor was achieved

Pitting corrosion of copper. Further model studies

International Nuclear Information System (INIS)

Taxen, C.

2002-08-01

The work presented in this report is a continuation and expansion of a previous study. The aim of the work is to provide background information about pitting corrosion of copper for a safety analysis of copper canisters for final deposition of radioactive waste. A mathematical model for the propagation of corrosion pits is used to estimate the conditions required for stationary propagation of a localised anodic corrosion process. The model uses equilibrium data for copper and its corrosion products and parameters for the aqueous mass transport of dissolved species. In the present work we have, in the model, used a more extensive set of aqueous and solid compounds and equilibrium data from a different source. The potential dependence of pitting in waters with different compositions is studied in greater detail. More waters have been studied and single parameter variations in the composition of the water have been studied over wider ranges of concentration. The conclusions drawn in the previous study are not contradicted by the present results. However, the combined effect of potential and water composition on the possibility of pitting corrosion is more complex than was realised. In the previous study we found what seemed to be a continuous aggravation of a pitting situation by increasing potentials. The present results indicate that pitting corrosion can take place only over a certain potential range and that there is an upper potential limit for pitting as well as a lower. A sensitivity analysis indicates that the model gives meaningful predictions of the minimum pitting potential also when relatively large errors in the input parameters are allowed for

Pitting corrosion on a copper canister

International Nuclear Information System (INIS)

Hermansson, H.P.; Beverskog, B.

1996-02-01

It is demonstrated that normal pitting can occur during oxidizing conditions in the repository. It is also concluded that a new theory for pitting corrosion has to be developed, as the present theory is not in accordance with all practical and experimental observations. A special variant of pitting, based on the growth of sulfide whiskers, is suggested to occur during reducing conditions. However, such a mechanism needs to be demonstrated experimentally. A simple calculational model of canister corrosion was developed based on the results of this study. 69 refs, 3 figs

Assessment and remediation of earthen pits in Alberta

International Nuclear Information System (INIS)

Lye, D.E.; Deibert, L.

1999-01-01

The proper decommissioning of abandoned earthen pits and the elimination of the associated environmental liabilities were discussed. An earthen pit is an excavated pit used by upstream oil and gas companies to contain/store/burn produced fluids and gases from either gas or oil producing operations. Produced fluids may include liquid hydrocarbons, process chemicals and water originating from oil wells, gas wells, and associated batteries and processing facilities. Improper operation and management at some pits has resulted in soil and/or groundwater contamination. In response to regulatory direction, petroleum operators in Alberta have begun the process of replacing earthen pits with alternative flaring and liquid storage facilities, and embarked on programs to assess, remediate and decommission earthen pits at their operations. This paper describes some of the challenges facing petroleum operators in this regard. It also outlines the regulatory framework within which decommissioning projects must be completed. 2 tabs

External Borrowing Framework an Investment Function Model For Turkish Economy (1998-2014 Period

Directory of Open Access Journals (Sweden)

Pelin KARATAY GÖGÜL

2016-12-01

Full Text Available External borrowing comes up as a result of savings-investment deficit. Some of belonging to the state of this debt determines budget deficit, some of belonging to the private sector of this debt determines financing needs of private sector. In terms of contribution of financing needs of private sector to fixed capital formation, external borrowing has a direct impact on economic growth and development is concerned. Borrowing from closing the budget deficit in the classic sense, rather than for Turkey's economy will be decisive in shaping the economic policies in order to finance of investments. This aim, By analyzing the 1998-2014 period for Turkey's economy if external borrowing is selected as a method of financing investment spending is investigated by using Multivariate Cointegration Analysis

12 CFR 617.7130 - What initial disclosures must a qualified lender make to a borrower?

Science.gov (United States)

2010-01-01

... lender make to a borrower? 617.7130 Section 617.7130 Banks and Banking FARM CREDIT ADMINISTRATION FARM... must a qualified lender make to a borrower? (a) Required disclosures—in general. A qualified lender... certificates that borrowers are required to purchase are at risk and may only be retired at the discretion of...

Recreating wetland ecosystems in an oil sands disturbed landscape : Suncor consolidated-tailings demonstration wetlands

Energy Technology Data Exchange (ETDEWEB)

Daly, C. [Suncor Energy, Fort McMurray, AB (Canada). Aquatic Reclamation Research; Tedder, W.; Marlowe, P. [Golder Associates Ltd., Calgary, AB (Canada). Oil Sands Div.

2009-10-01

Open pit oil sands mining involves the disturbance of thin overburden covers of Boreal forest lands that must be returned to equivalent land capability after mining activities have ceased. Before mining starts, any wetlands are drained, timber is harvested, and peat, topsoils and subsoils are stockpiled for later use. This article discussed wetland reclamation activities conducted by Suncor Energy at its open pit mining operations. Research facilities were constructed in order to determine if wetlands constructed with consolidated tailings (CT) and pond effluent water (PEW) were able to support a sustainable vegetation community. Thirty-three cat-tail plots were established at the facility as well as unplanted plots in order to determine how quickly natural establishment occurred. Shoreline plug transplants and transplants from a natural saline lake were also introduced. Within 5 years, over 23 plant species had naturally colonized the CT wetlands. However, diversity was lower in CT and PEW-constructed wetlands. It was concluded that the application of a native peat-mineral mix soil may help to increase plant diversity. 20 refs., 5 figs.

The Application of Foundation Pit Monitoring Technology to the Excavation

Directory of Open Access Journals (Sweden)

Qiu Jin

2015-01-01

Full Text Available The foundation pit monitoring plays an important role in the foundation pit supporting projects especially in those deep foundation pit projects. Through the whole monitoring of the foundation pit construction from the excavation to the backfill, we can learn about the forcing and deforming process of the foundation pit supporting system, and grasp the impact of external condition changes on the foundation pit. This paper takes a project in Jinan as an example to establish a specific monitoring program, and then conducts the analysis and evaluation of the monitoring data; the real-time grasp of the foundation pit deformation and internal force changes can help to further ensure the security status of the foundation pit, thus better guiding the construction.

Inhibition of Copper Pitting Corrosion in Aggressive Potable Waters

Directory of Open Access Journals (Sweden)

Emily Sarver

2012-01-01

Full Text Available Copper pitting corrosion can lead to premature plumbing failures, and can be caused by aggressive potable waters characterized by high pH, free chlorine residual and low alkalinity. In such waters and under continuous flow, certain inhibitors including phosphate, silica or natural organic matter may greatly reduce pitting occurrence. In the current work, 1 mg/L phosphate (as P completely prevented initiation of pits, and 5 mg/L silica (as Si significantly decelerated pitting. However, much lower doses of these inhibitors had little benefit and actually accelerated the rate of attack in some cases. Effects of organic matter were dependent on both the type (e.g., natural versus ozonated humic substances and dosage. Dose-response effects of free chlorine and alkalinity were also investigated. Based on electrochemical data, pits initiated more rapidly with increased free chlorine, but even moderate levels of chlorine (~0.4 mg/L eventually caused severe pitting. High alkalinity decreased pit propagation rates but did not prevent pit formation.

12 CFR 615.5040 - Borrowings from financial institutions other than commercial banks.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Borrowings from financial institutions other than commercial banks. 615.5040 Section 615.5040 Banks and Banking FARM CREDIT ADMINISTRATION FARM... § 615.5040 Borrowings from financial institutions other than commercial banks. The Farm Credit banks may...

Fuzzy Portfolio Selection Problem with Different Borrowing and Lending Rates

OpenAIRE

Chen, Wei; Yang, Yiping; Ma, Hui

2011-01-01

As we know, borrowing and lending risk-free assets arise extensively in the theory and practice of finance. However, little study has ever investigated them in fuzzy portfolio problem. In this paper, the returns of each assets are assumed to be fuzzy variables, then following the mean-variance approach, a new possibilistic portfolio selection model with different interest rates for borrowing and lending is proposed, in which the possibilistic semiabsolute deviation of the return is used to...

The customers borrowing behavior during the financial crisis

Directory of Open Access Journals (Sweden)

Alina LUCA (BRĂTUCU

2013-05-01

Full Text Available The global financial crisis determined the transition of the Romanian banking system from excess of liquidity to deficit, namely from an aggressive lending activity to a significant reduction of credit growth rate. In our country, the high indebtedness rate, especially in foreign currencies, is the main vulnerable spot of the population sector. The main objective of this paperwork is to analyze factors that influence the customers in their decision to borrow in foreign currencies or in Ron. In this matter, it was used a regional econometric model for panel data in order to see Romania’s customers borrowing preferences and to analyze if the crises have changed their behavior.

Detecting pits in tart cherries by hyperspectral transmission imaging

Science.gov (United States)

Qin, Jianwei; Lu, Renfu

2004-11-01

The presence of pits in processed cherry products causes safety concerns for consumers and imposes potential liability for the food industry. The objective of this research was to investigate a hyperspectral transmission imaging technique for detecting the pit in tart cherries. A hyperspectral imaging system was used to acquire transmission images from individual cherry fruit for four orientations before and after pits were removed over the spectral region between 450 nm and 1,000 nm. Cherries of three size groups (small, intermediate, and large), each with two color classes (light red and dark red) were used for determining the effect of fruit orientation, size, and color on the pit detection accuracy. Additional cherries were studied for the effect of defect (i.e., bruises) on the pit detection. Computer algorithms were developed using the neural network (NN) method to classify the cherries with and without the pit. Two types of data inputs, i.e., single spectra and selected regions of interest (ROIs), were compared. The spectral region between 690 nm and 850 nm was most appropriate for cherry pit detection. The NN with inputs of ROIs achieved higher pit detection rates ranging from 90.6% to 100%, with the average correct rate of 98.4%. Fruit orientation and color had a small effect (less than 1%) on pit detection. Fruit size and defect affected pit detection and their effect could be minimized by training the NN with properly selected cherry samples.

Cultural borrowing - Serbian jogurt between the east and the west

Directory of Open Access Journals (Sweden)

Petrović Snežana M.

2015-01-01

Full Text Available The paper offers an analysis of the cultural borrowing process of the Turkish word yoğurt ‘yogurt’ in Serbian. The study begins with the analysis of the Serbian lexical material from the 19th century, when the word jogurt was marked as an exclusively foreign word. The comparison with the present status of the meaning and usage of the word jogurt in contemporary Serbian, in which the word is part of the standard language, shows two different layers of the borrowing process: the Ottoman Turkish period and the Non-Turkish one. The most recent, Post-Ottoman borrowing layer is illustrated by the usage of jogurt as an element of a proverb that is a calque from the Turk. Sutten ağzı yanan yoğurdu (veya ayranı ufleyerek yer (veya icer “who gets burned by milk, blows into yogurt as well”. Aiming to present a complex process of this cultural borrowing, the data from Serbian is compared to the relevant data from other Balkan and European languages. [Projekat Ministarstva nauke Republike Srbije, br. 178007: Etimološka istraživanja srpskog jezika i izrada Etimološkog rečnika srpskog jezika i br. 178009: Lingvistička istraživanja savremenog srpskog književnog jezika i izrada Rečnika srpskohrvatskog književnog i narodnog jezika SANU

Open Pit Water Control Safety A Case Of Nchanga Open Pit Mine Zambia

OpenAIRE

Silwamba C; Chileshe P R K

2015-01-01

Abstract Mining in Chingola Zambia started underground in 1931 and was catastrophically flooded and closed. The present Nchanga Underground Mine NUG started in 1937. The Nchanga Open Pit NOP mine started in 1955 situated to the west of NUG and partially overlying it. Open pit water control safety operations in the Nchanga-Chingola area have successfully enabled the safe extraction of millions of tonnes of copper ore annually over the past 60 years from NUG mining as well as the NOP. At the st...

Investigating pitting in X65 carbon steel using potentiostatic polarisation

Science.gov (United States)

Mohammed, Sikiru; Hua, Yong; Barker, R.; Neville, A.

2017-11-01

Although pitting corrosion in passive materials is generally well understood, the growth of surface pits in actively-corroding materials has received much less attention to date and remains poorly understood. One of the key challenges which exists is repeatedly and reliably generating surface pits in a practical time-frame in the absence of deformation and/or residual stress so that studies on pit propagation and healing can be performed. Another pertinent issue is how to evaluate pitting while addressing general corrosion in low carbon steel. In this work, potentiostatic polarisation was employed to induce corrosion pits (free from deformation or residual stress) on actively corroding X65 carbon steel. The influence of applied potential (50 mV, 100 mV and 150 mV vs open circuit potential) was investigated over 24 h in a CO2-saturated, 3.5 wt.% NaCl solution at 30 °C and pH 3.8. Scanning electron microscopy (SEM) was utilised to examine pits, while surface profilometry was conducted to measure pit depth as a function of applied potential over the range considered. Analyses of light pitting (up to 120 μm) revealed that pit depth increased linearly with increase in applied potential. This paper relates total pit volume (measured using white light interferometry) to dissipated charge or total mass loss (using the current response for potentiostatic polarisation in conjunction with Faraday's law). By controlling the potential of the surface (anodic) the extent of pitting and general corrosion could be controlled. This allowed pits to be evaluated for their ability to continue to propagate after the potentiostatic technique was employed. Linear growth from a depth of 70 μm at pH 3.8, 80 °C was demonstrated. The technique offers promise for the study of inhibition of pitting.

Pitting of malaria parasites and spherocyte formation

Directory of Open Access Journals (Sweden)

Gichuki Charity W

2006-07-01

Full Text Available Abstract Background A high prevalence of spherocytes was detected in blood smears of children enrolled in a case control study conducted in the malaria holoendemic Lake Victoria basin. It was speculated that the spherocytes reflect intraerythrocytic removal of malarial parasites with a concurrent removal of RBC membrane through a process analogous to pitting of intraerythrocytic inclusion bodies. Pitting and re-circulation of RBCs devoid of malaria parasites could be a host mechanism for parasite clearance while minimizing the anaemia that would occur were the entire parasitized RBC removed. The prior demonstration of RBCs containing ring-infected erythrocyte surface antigen (pf 155 or RESA but no intracellular parasites, support the idea of pitting. Methods An in vitro model was developed to examine the phenomenon of pitting and spherocyte formation in Plasmodium falciparum infected RBCs (iRBC co-incubated with human macrophages. In vivo application of this model was evaluated using blood specimens from patients attending Kisumu Ditrict Hospital. RBCs were probed with anti-RESA monoclonal antibody and a DNA stain (propidium iodide. Flow cytometry and fluorescent microscopy was used to compare RBCs containing both the antigen and the parasites to those that were only RESA positive. Results Co-incubation of iRBC and tumor necrosis factor-alpha activated macrophages led to pitting (14% ± 1.31% macrophages with engulfed trophozoites as opposed to erythrophagocytosis (5.33% ± 0.95% (P Conclusion It is proposed that in malaria holoendemic areas where prevalence of asexual stage parasites approaches 100% in children, RBCs with pitted parasites are re-circulated and pitting may produce spherocytes.

CRSMP Potential Coastal and Upland Borrow Sites 2012

Data.gov (United States)

California Natural Resource Agency — Upland debris basins and coastal borrow sites as identified originally in the California Shoreline Database compiled by Noble Consultants (Jon Moore). Later updates...

7 CFR 1980.441 - Borrower equity requirements.

Science.gov (United States)

2010-01-01

... management history vs. start-up businesses; personal/corporate guarantees offered; contractual relationships... BUSINESS-COOPERATIVE SERVICE, RURAL UTILITIES SERVICE, AND FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE (CONTINUED) PROGRAM REGULATIONS (CONTINUED) GENERAL Business and Industrial Loan Program § 1980.441 Borrower...

Pitting corrosion of copper. An equilibrium - mass transport study

Energy Technology Data Exchange (ETDEWEB)

Taxen, C

1996-11-01

A mathematical model for the propagation of corrosion pits on copper is described. The model is used to predict the potentials below which copper is immune to pitting. The criteria used for immunity against pitting is that the volume of the cuprous oxide formed at the site of the metal oxidation at the bottom of a corrosion pit must be smaller than the volume of the oxidised metal. Equal volumes would give a complete coverage of the metal in a pit by adherent cuprous oxide and propagation would not be possible. For potentials where copper is not immune to pitting an estimate of the maximum growth rate is given. The model uses equilibrium data and diffusion coefficients and calculates the stationary concentration profiles from the bulk water outside a corrosion pit to the site of the metal dissolution at the bottom a corrosion pit. Precipitation of oxides as well as of basic salts of copper is considered. A total of 26 aqueous species are considered in waters with compositions ranging from those of tap waters to that of sea water. Calculations are made for the temperatures 25 deg C and 75 deg C. 38 refs, 60 figs, 17 tabs

Research process of nondestructive testing pitting corrosion in metal material

Directory of Open Access Journals (Sweden)

Bo ZHANG

2017-12-01

Full Text Available Pitting corrosion directly affects the usability and service life of metal material, so the effective nondestructive testing and evaluation on pitting corrosion is of great significance for fatigue life prediction because of data supporting. The features of pitting corrosion are elaborated, and the relation between the pitting corrosion parameters and fatigue performance is pointed out. Through introducing the fundamental principles of pitting corrosion including mainly magnetic flux leakage inspection, pulsed eddy current and guided waves, the research status of nondestructive testing technology for pitting corrosion is summarized, and the key steps of nondestructive testing technologies are compared and analyzed from the theoretical model, signal processing to industrial applications. Based on the analysis of the signal processing specificity of different nondestructive testing technologies in detecting pitting corrosion, the visualization combined with image processing and signal analysis are indicated as the critical problems of accurate extraction of pitting defect information and quantitative characterization for pitting corrosion. The study on non-contact nondestructive testing technologies is important for improving the detection precision and its application in industries.

7 CFR 1735.14 - Borrower eligibility.

Science.gov (United States)

2010-01-01

... liability company. [58 FR 66253, Dec. 20, 1993, as amended at 64 FR 50429, Sept. 17, 1999; 65 FR 42619, July... in rural areas as of October 28, 1949; and (3) Cooperative, nonprofit, limited dividend or mutual..., nonprofit, limited dividend, or mutual associations. To be eligible for a loan, a borrower: (1) Must have...

7 CFR 1717.857 - Refinancing of existing secured debt-distribution and power supply borrowers.

Science.gov (United States)

2010-01-01

... the proposed loan; (4) The borrower's financial and statistical report, the data in which shall not be... delinquency and the reasons therefor; and a certification, if not previously provided, that the borrower has...

Fuzzy Portfolio Selection Problem with Different Borrowing and Lending Rates

Directory of Open Access Journals (Sweden)

Wei Chen

2011-01-01

the returns of each assets are assumed to be fuzzy variables, then following the mean-variance approach, a new possibilistic portfolio selection model with different interest rates for borrowing and lending is proposed, in which the possibilistic semiabsolute deviation of the return is used to measure investment risk. The conventional probabilistic mean variance model can be transformed to a linear programming problem under possibility distributions. Finally, a numerical example is given to illustrate the modeling idea and the impact of borrowing and lending on optimal decision making.

Qualified to Lead? A Comparative, Contextual and Cultural View of Educational Policy Borrowing

Science.gov (United States)

Harris, Alma; Jones, Michelle; Adams, Donnie

2016-01-01

Background: Around the globe, education policy borrowing remains pervasive and prevalent. The strategies, interventions and innovations of education systems that perform well, in international assessments, are enthusiastically borrowed and copied in the anticipation of similar educational performance and outcomes. Purpose: This purpose of the…

19 Additive and Substitutive Borrowing against Semantic ...

African Journals Online (AJOL)

reflexes mean 'to forge' and/or 'black-smith' (Ibid, 49). The Theory of Semantic Narrowing and Broadening in the. Realm of Lexical Borrowing ..... should be noticed that the traditional label referred to a hole on the whole of a traditional house ...

RCRA Closure Plan for the Bear Creek Burial Grounds B Area and Walk-In Pits at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1993-04-01

In June 1987, the RCRA Closure/Postclosure Plan for the Bear Creek Burial Grounds (BCBG) was submitted to the Tennessee Department of Environment and Conservation (TDEC) for review and approval. TDEC modified and issued the plan approved on September 30, 1987. Y/TS-395 was initially intended to apply to A Area, C-West, B Area, and the Walk-In Pits of BCBG. However, a concept was developed to include the B Area (non-RCRA regulated) in the Walk-In Pits so that both areas would be closed under one cap. This approach included a tremendous amount of site preparation with an underlying stabilization base of 16 ft of sand for blast protection. In January 1993, the Closure Plan was revised to include inspection and maintenance criteria and to reflect that future monitoring and remediation would be conducted as part of the ongoing Comprehensive Environmental Response, Compensation, and Liability Act activities at the Oak Ridge Y-12 Plant. This Closure Plan revision is intended to reflect the placement of the Kerr Hollow Quarry debris at the Walk-In Pits, revise the closure dates, and acknowledge that the disposition of a monitoring well within the closure site cannot be verified

Spontaneous Resolution of Optic Disc Pit Maculopathy

OpenAIRE

Tripathy, Koushik

2017-01-01

I read with interest the article reporting spontaneous resolution of optic disc pit maculopathy in a boy.1 Though the presence of an optic disc pit and associated macular involvement is undoubted in the presented case, the provided optical coherence tomography (OCT) does not clearly show typical intraretinal schisis (Figure 1B)1 at multiple retinal levels which may communicate with the pit. Instead, it shows a sub-internal limiting membrane (sub-ILM) cavity. Such cavities are known to occur f...

Sand transportation and reverse patterns over leeward face of sand dune

Science.gov (United States)

Jiang, Hong; Dun, Hongchao; Tong, Ding; Huang, Ning

2017-04-01

Sand saltation has complex interactions with turbulent flow and dune form. Most models of wind-blown sand consider ideal circumstances such as steady wind velocity and a flat surface, and the bulk of data on wind flow and sand transport over an individual dune has focused mostly on the influence of dune shape or inter-dune space on the wind flow, neglecting the effect of morphology on sand saltation, particularly airflow and sand transportation over the leeward slope. Wind flow structures over the leeward slope of sand dunes have a fundamental influence on the organization of sand dunes. In order to understand sand dune dynamics, lee face airflow and sediment transportation should be paid more attention. Previous field observations could not measure turbulent flow structure well because of the limited observation points and the influence of experiment structure on wind field. In addition, the reverse sand particles over leeward face could not be collected by sand trap in field. Numerous field observations could not measure turbulent flow structure because of the limited observation points and the influence of experimental structures on the wind field. In addition, the reverse transport of sand particles over leeward face could not be collected by sand traps in field. Therefore, this paper aims to investigate the turbulent flow structure and sand transport pattern over the leeward slope. A numerical model of sand saltation over slope terrain is constructed, which also considers the coupling effects between air flow and sand particles. The large eddy simulation method is used to model turbulent flow. Sand transport is simulated by tracking the trajectory of each sand particle. The results show that terrain significantly alters the turbulent air flow structure and wind-blown sand movement, especially over the leeward slope. Here, mass flux increases initially and then decreases with height in the reversed flow region in the direction of wind flow, and the mass flux

K West Basin Sand Filter Backwash Sample Analysis

Energy Technology Data Exchange (ETDEWEB)

Fiskum, Sandra K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Smoot, Margaret R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Coffey, Deborah S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pool, Karl N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-03-01

A sand filter is used to help maintain water clarity at the K West Basin where highly radioactive sludge is stored. Eventually that sand filter will require disposal. The radionuclide content of the solids trapped in the sand filter will affect the selection of the sand filter disposal pathway. The Pacific Northwest National Laboratory (PNNL) was contracted by the K Basin Operations & Plateau Remediation Project (operations contractor CH2M Hill) to analyze the radionuclide content of the solids collected from the backwash of the K West Basin sand filter. The radionuclide composition in the sand filter backwash solids will be used by CH2M Hill to determine if the sand filter media and retained sludge solids will be designated as transuranic waste for disposal purposes or can be processed through less expensive means. On October 19, 2015, K Basin Operations & Plateau Remediation Project staff backwashed the sand filter into the North Load-Out Pit (NLOP) and immediately collected sample slurry from a sampling tube positioned 24 in. above the NLOP floor. The 764 g sand filter backwash slurry sample, KW-105 SFBW-001, was submitted to PNNL for analysis on October 20, 2015. Solids from the slurry sample were consolidated into two samples (i.e., a primary and a duplicate sample) by centrifuging and measured for mass (0.82 g combined – wet centrifuged solids basis) and volume (0.80 mL combined). The solids were a dark brown/orange color, consistent with iron oxide/hydroxide. The solids were dried; the combined dry solids mass was 0.1113 g, corresponding to 0.0146 weight percent (wt%) solids in the original submitted sample slurry. The solids were acid-digested using nitric and hydrochloric acids. Insoluble solids developed upon dilution with 0.5 M HNO₃, corresponding to an average 6.5 wt% of the initial dry solids content. The acid digestate and insoluble solids were analyzed separately by gamma spectrometry. Nominally, 7.7% of the ⁶⁰Co was present

Borrowing constraints, multiple equilibria and monetary policy

NARCIS (Netherlands)

Assenza, T.

2007-01-01

The appealing feature of Kiyotaki and Moore's Financial Accelerator model (Kiyotaki and Moore, 1997, 2002) is the linkage of asset price changes and borrowing constraints. This framework therefore is the natural vehicle to explore the net worth channel of the monetary transmission mechanism. In the

24 CFR 201.22 - Credit requirements for borrowers.

Science.gov (United States)

2010-04-01

... consumer credit report stating the credit accounts and payment history of the borrower and of any co-maker... months or more. (c) Evidence of delinquency, default or misrepresentation. Except with the prior approval...

How Culture Matters in Educational Borrowing? Chinese Teachers' Dilemmas in a Global Era

Science.gov (United States)

Liu, Sheng-nan; Feng, Da-ming

2015-01-01

Educational borrowing may cause numerous dilemmas that emerge from cross-cultural differences among teachers in the globalization. Through the case study on the flipped classroom introduced from the United States into Chinese middle schools, this article presents an examination of dilemmas that teachers encountered during educational borrowing in…

LANDSLIDE RECLAMATION IN ŠÁRKA VALLEY

Directory of Open Access Journals (Sweden)

Martin Vaníček

2017-10-01

Full Text Available Housing development in Šárka’s valley is situated in former brickworks – borrow pit for brick-clay. On its north side the borrow pit cutting is up to 8m high with main road on top. This slope was suffering from progressive landslide mainly due to weathering and surface erosion. The reclamation works proposed and afterwards executed consisted of stabilizing the slope by combination of soil nailing and connecting reinforced slope with surcharge bench at its toe. The final reinforced soil structure nicely merged into the surrounding environment.

Pit Study, Geographic NAD83, LOSCO (1999) [pit_study_LOSCO_1998

Data.gov (United States)

Louisiana Geographic Information Center — The 'Pit Study' was meant to identify the remnants of former oil extraction sites which pose the threat of creating an oil spill. These remnants include many other...

A new depositional model for sand-rich loess on the Buckley Flats outwash plain, northwestern Lower Michigan

Science.gov (United States)

Nyland, Kelsey E.; Schaetzl, Randall J.; Ignatov, Anthony; Miller, Bradley A.

2018-04-01

Loess was first studied in Michigan on the Buckley Flats, where outwash, overlain by ≈70 cm of loamy sediment, was originally interpreted as loess mixed with underlying sands. This paper re-evaluates this landscape through a spatial analysis of data from auger samples and soil pits. To better estimate the loamy sediment's initial textures, we utilized "filtered" laser diffraction data, which remove much of the coarser sand data. Textures of filtered silt data for the loamy sediment are similar to loess. The siltiest soils are found in the low-relief, central part of the Flats. Spatial analyses revealed that many silt fractions are nearly uniformly distributed, suggesting that the loess was not derived from a single source. The previous depositional model for the loamy mantle relied on loessfall followed by pedoturbation, but does not explain (1) the variation in sand contents across the Flats, or (2) the abrupt contact below the loamy mantle. This contact suggests that the outwash was frozen when the sediments above were deposited. Deep gullies at the western margins of the Flats were likely cut as permafrost facilitated runoff. Our new model for the origin of the loamy mantle suggests that the sands on the uplands were generated from eroding gullies and saltated onto the uplands along with loess that fell more widely. Sands saltating to the west of the Flats may have entrained some silts, facilitating loessfall downwind. At most sites, the loamy mantle gets increasingly silty near the surface, suggesting that saltation ended before loess deposition.

International Education Policy Transfer--Borrowing Both Ways: The Hong Kong and England Experience

Science.gov (United States)

Forestier, Katherine; Crossley, Michael

2015-01-01

This paper analyses how the impact of international student achievement studies and the recent economic crisis in Europe are influencing the development of educational policy transfer and borrowing, from East to West. This is contrasted with education reform movements in East Asia, which have long legacies of borrowing from so-called…

Education Policy Borrowing in China: Has the West Wind Overpowered the East Wind?

Science.gov (United States)

Tan, Charlene; Chua, Catherine S. K.

2015-01-01

Recent education reform in China reflects the global trend of education policy borrowing from Anglophone countries such as the USA. The reform in China essentially advocates shifting from knowledge reproduction and didacticism to knowledge construction by students through a learner-centredness approach. Aware of the trend of borrowing policy from…

Markov chain modelling of pitting corrosion in underground pipelines

Energy Technology Data Exchange (ETDEWEB)

Caleyo, F. [Departamento de Ingenieri' a Metalurgica, ESIQIE, IPN, UPALM Edif. 7, Zacatenco, Mexico D. F. 07738 (Mexico)], E-mail: fcaleyo@gmail.com; Velazquez, J.C. [Departamento de Ingenieri' a Metalurgica, ESIQIE, IPN, UPALM Edif. 7, Zacatenco, Mexico D. F. 07738 (Mexico); Valor, A. [Facultad de Fisica, Universidad de La Habana, San Lazaro y L, Vedado, 10400 La Habana (Cuba); Hallen, J.M. [Departamento de Ingenieri' a Metalurgica, ESIQIE, IPN, UPALM Edif. 7, Zacatenco, Mexico D. F. 07738 (Mexico)

2009-09-15

A continuous-time, non-homogenous linear growth (pure birth) Markov process has been used to model external pitting corrosion in underground pipelines. The closed form solution of Kolmogorov's forward equations for this type of Markov process is used to describe the transition probability function in a discrete pit depth space. The identification of the transition probability function can be achieved by correlating the stochastic pit depth mean with the deterministic mean obtained experimentally. Monte-Carlo simulations previously reported have been used to predict the time evolution of the mean value of the pit depth distribution for different soil textural classes. The simulated distributions have been used to create an empirical Markov chain-based stochastic model for predicting the evolution of pitting corrosion depth and rate distributions from the observed properties of the soil. The proposed model has also been applied to pitting corrosion data from pipeline repeated in-line inspections and laboratory immersion experiments.

Markov chain modelling of pitting corrosion in underground pipelines

International Nuclear Information System (INIS)

Caleyo, F.; Velazquez, J.C.; Valor, A.; Hallen, J.M.

2009-01-01

A continuous-time, non-homogenous linear growth (pure birth) Markov process has been used to model external pitting corrosion in underground pipelines. The closed form solution of Kolmogorov's forward equations for this type of Markov process is used to describe the transition probability function in a discrete pit depth space. The identification of the transition probability function can be achieved by correlating the stochastic pit depth mean with the deterministic mean obtained experimentally. Monte-Carlo simulations previously reported have been used to predict the time evolution of the mean value of the pit depth distribution for different soil textural classes. The simulated distributions have been used to create an empirical Markov chain-based stochastic model for predicting the evolution of pitting corrosion depth and rate distributions from the observed properties of the soil. The proposed model has also been applied to pitting corrosion data from pipeline repeated in-line inspections and laboratory immersion experiments.

Mutual Word Borrowings between the English and the Spanish Languages

Directory of Open Access Journals (Sweden)

Aliya Rinatovna Ismagilova

2017-09-01

Full Text Available The contemporary world witnesses growing popularity of foreign languages learning and their role in the modern society. The article is devoted to the problem of mutual borrowings from English and Spanish languages. The aim of the article is to investigate new tendencies in the English words borrowings, their establishment in the Spanish language and the other way round. The Spanish language is one of the most widespread languages in the world and it is a native language for different nationalities. On the other hand, English has borrowed quite a lot of Spanish words as well. The mutual enrichment of the languages makes the process of language teaching specific and it is important in the modern process of globalization where languages are the main resource of international cooperation. The article contains both theoretical and practical materials dedicated to the investigation of this problem. This article may be useful for a wide range of readers, students, scientists, linguists in the study of modern Spanish and English languages.

Force-displacement measurements of earlywood bordered pits using a mesomechanical tester.

Science.gov (United States)

Zelinka, Samuel L; Bourne, Keith J; Hermanson, John C; Glass, Samuel V; Costa, Adriana; Wiedenhoeft, Alex C

2015-10-01

The elastic properties of pit membranes are reported to have important implications in understanding air-seeding phenomena in gymnosperms, and pit aspiration plays a large role in wood technological applications such as wood drying and preservative treatment. Here we present force-displacement measurements for pit membranes of circular bordered pits, collected on a mesomechanical testing system. The system consists of a quartz microprobe attached to a microforce sensor that is positioned and advanced with a micromanipulator mounted on an inverted microscope. Membrane displacement is measured from digital image analysis. Unaspirated pits from earlywood of never-dried wood of Larix and Pinus and aspirated pits from earlywood of dried wood of Larix were tested to generate force-displacement curves up to the point of membrane failure. Two failure modes were observed: rupture or tearing of the pit membrane by the microprobe tip, and the stretching of the pit membrane until the torus was forced out of the pit chamber through the pit aperture without rupture, a condition we refer to as torus prolapse. Published 2015. This article is a U.S. Government work and is in the public domain in the USA.

Borrowing and Dictionary Compilation: The Case of the Indigenous South African Languages

Directory of Open Access Journals (Sweden)

Munzhedzi James Mafela

2011-10-01

Full Text Available

ABSTRACT: Borrowing occurs when a language adds a word from another language to its own lexicon. Languages in neighbouring regions often borrow from each other. In South Africa, there are over nine indigenous languages, in addition to Afrikaans and English, all of which coexist. In their coexistence they borrow from one another. African language dictionaries reveal that these languages have borrowed a great deal from Afrikaans and English. However, one would expect these dictionaries to reflect some borrowing from other indigenous languages; on the contrary, they include very few such words. Although, one encounters many words from indigenous languages being used by other African languages in their spoken language and literary works, these are not included in dictionaries. This article seeks to highlight factors contributing to the failure to include words borrowed from other indigenous languages in African language dictionaries.

OPSOMMING: Ontlening en woordeboeksamestelling: Die geval van inheemse Suid-Afrikaanse tale. Ontlening vind plaas wanneer 'n taal 'n woord uit 'n ander taal by sy eie leksikon voeg. Tale in aangrensende streke leen dikwels van mekaar. Daar is meer as nege inheemse tale in Suid-Afrika, bo en behalwe Afrikaans en Engels, wat saam bestaan. In hulle naasbestaan leen hulle van mekaar. Afrikataal-woordeboeke getuig daarvan dat hierdie tale heelwat uit Afrikaans en Engels geleen het. Daar sou egter verwag kon word dat hierdie woordeboeke sal getuig van ontlening uit ander inheemse tale; in teendeel, hulle sluit baie min van sulke woorde in. Alhoewel baie woorde van inheemse tale in ander Afrikatale gebruik word in die gesproke taal en letterkundige werke, is hierdie woorde nie in die woordeboeke opgeneem nie. Die doel van hierdie artikel is om die faktore uit te lig wat bydra tot die versuim om leenwoorde van ander inheemse tale in die Afrikataal-woordeboeke op te neem.

Sleutelwoorde: ONTLENING

Reclaimability of the spent sand mixture – sand with bentonite – sand with furfuryl resin

Directory of Open Access Journals (Sweden)

J. Dańko

2011-04-01

Full Text Available Introduction of new binding materials and new technologies of their hardening in casting moulds and cores production requires theapplication of reclamation methods adequate to their properties as well as special devices realizing tasks. The spent sands circulationsystem containing the same kind of moulding and core sands is optimal from the point of view of the expected reclamation results.However, in the face of a significant variability of applied technologies and related to them various reclamation methods, the need - of theobtained reclamation products assessment on the grounds of systematic criteria and uniform bases – arises, with a tendency of indicatingwhich criteria are the most important for the given sand system. The reclaimability results of the mixture of the spent moulding sand withGeko S bentonite and the spent core sand with the Kaltharz 404U resin hardened by acidic hardener 100 T3, are presented in the paper.Investigations were performed with regard to the estimation of an influence of core sands additions (10 –25% on the reclaimed materialquality. Dusts and clay content in the reclaim, its chemical reaction (pH and ignition loss were estimated. The verification of the reclaiminstrumental assessment was performed on the basis of the technological properties estimation of moulding sand with bentonite, where the reclaimed material was used as a matrix.

THE BORROWER CHARACTERISTICS IN HOT EQUITY MARKETS

Directory of Open Access Journals (Sweden)

HALIL DINCER KAYA

2017-06-01

Full Text Available In this study, I examine the characteristics of U.S. corporate borrowers (public debt, private placement, and syndicated loan firms in HOT versus COLD equity markets. My main objective is to see the characteristics of firms that choose debt financing even when the equity market is HOT. HOT equity markets are defined as the top twenty percent of the months in terms of the de-trended number of equity offerings. I find that the HOT equity market borrowers generally have higher market-to-book ratios compared to the COLD market borrowers. Also, in HOT equity markets, the public debt firms (i.e. the corporate bond issuers tend to have fewer tangible assets, the private placement firms tend to be smaller and highly levered, and the syndicated loan firms tend to be smaller, more profitable, and less levered compared to the COLD market firms. When I look at the number of transactions in each market, I find that when the equity market is active (i.e. HOT, the syndicated loan market is even more active. During these periods, the public debt market is also active (although not as much as the equity or the syndicated loan markets. When I look at the sizes of the transactions in each market, I find that the private placements tend to be significantly larger in HOT markets compared to COLD markets. I conclude that while the equity, the public debt, and the syndicated loan markets move together in terms of market activity, the equity market and the private placement markets move together in terms of the size of the transaction.

The Upper Miocene Lake Pannon marl from the Filijala Open Pit (Beočin, northern Serbia: New geological and paleomagnetic data

Directory of Open Access Journals (Sweden)

Ganić Meri

2010-01-01

Full Text Available This work presents major lithological, structural, paleontological and paleomagnetic characteristics of the Upper Miocene Pannonian marl in the Filijala Open Pit of the La Farge Cement Plant near Beočin, northern Serbia. Pannonian marl lies between the underlying heterogeneous Sarmatian deposits and the overlying set of Pontian sand beds and Quaternary sediments. The open pit is located on the NE range of Fruška Gora, a horst structure with a core of Paleozoic, Mesozoic and Paleogene rocks in a complex structural pattern. Pannonian sediments, which are part of a younger structural stage, deposited on the horst limbs. The Pannonian marl strata dip at angles from 12° to 26° (to the NNW, forming a monocline. The strata deformations are a consequence of radial tectonics and are a potential source of landslides. The many mollusks (7 gastropod and 9 bivalve species and ostracodes (27 species and their biostratigraphical position indicate marl deposition throughout the Pannonian age. A paleomagnetic investigation established that the marl has inconsistent remanent magnetization (with bad statistical parameters, which originates from neoformed magnetite.

Inconsistent identification of pit bull-type dogs by shelter staff.

Science.gov (United States)

Olson, K R; Levy, J K; Norby, B; Crandall, M M; Broadhurst, J E; Jacks, S; Barton, R C; Zimmerman, M S

2015-11-01

Shelter staff and veterinarians routinely make subjective dog breed identification based on appearance, but their accuracy regarding pit bull-type breeds is unknown. The purpose of this study was to measure agreement among shelter staff in assigning pit bull-type breed designations to shelter dogs and to compare breed assignments with DNA breed signatures. In this prospective cross-sectional study, four staff members at each of four different shelters recorded their suspected breed(s) for 30 dogs; there was a total of 16 breed assessors and 120 dogs. The terms American pit bull terrier, American Staffordshire terrier, Staffordshire bull terrier, pit bull, and their mixes were included in the study definition of 'pit bull-type breeds.' Using visual identification only, the median inter-observer agreements and kappa values in pair-wise comparisons of each of the staff breed assignments for pit bull-type breed vs. not pit bull-type breed ranged from 76% to 83% and from 0.44 to 0.52 (moderate agreement), respectively. Whole blood was submitted to a commercial DNA testing laboratory for breed identification. Whereas DNA breed signatures identified only 25 dogs (21%) as pit bull-type, shelter staff collectively identified 62 (52%) dogs as pit bull-type. Agreement between visual and DNA-based breed assignments varied among individuals, with sensitivity for pit bull-type identification ranging from 33% to 75% and specificity ranging from 52% to 100%. The median kappa value for inter-observer agreement with DNA results at each shelter ranged from 0.1 to 0.48 (poor to moderate). Lack of consistency among shelter staff indicated that visual identification of pit bull-type dogs was unreliable. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Sustainable Environmental Protection Using Modified Pit-Latrines

NARCIS (Netherlands)

Chaggu, E.J.

2004-01-01

Pit-latrines are on-site excreta disposal facilities widely used as anaerobic accumulation system for stabilizing human wastes like excreta, both in rural and urban settlements of developing countries. Flooding of pit-latrines is often a common phenomenon, especially in situations of high water

Pitting corrosion of copper. An equilibrium - mass transport study

International Nuclear Information System (INIS)

Taxen, C.

2002-08-01

A mathematical model for the propagation of corrosion pits is described and used to calculate the potentials below which copper is immune to pitting. The model uses equilibrium data and diffusion coefficients and calculates the stationary concentration profiles of 26 aqueous species from the bulk water outside a corrosion pit to the site of the metal dissolution. Precipitation of oxides and salts of copper is considered. Studied conditions include water compositions from tap waters to seawater at the temperatures 25 deg C and 75 deg C. Carbonate and sulphate are aggressive towards copper because of complex formation with divalent copper. Carbonate is less aggressive in a corrosion pit than outside at the pH of the bulk. Carbonate carries acidity out from the pit, favours oxide formation and may prevent the initiation of acidic corrosion pits. The concentration profiles are used to estimate the maximum propagation rates for a corrosion pit. A high potential is found to be the most important factor for the rate of propagation. The levels of potential copper can sustain, as corrosion potentials are discussed in terms of the stability of cuprous oxide as a cathode material for oxygen reduction relative to non-conducting cupric phases

Pitting corrosion of copper. An equilibrium - mass transport study

Energy Technology Data Exchange (ETDEWEB)

Taxen, C. [Swedish Corrosion Inst., Stockholm (Sweden)

2002-08-01

A mathematical model for the propagation of corrosion pits is described and used to calculate the potentials below which copper is immune to pitting. The model uses equilibrium data and diffusion coefficients and calculates the stationary concentration profiles of 26 aqueous species from the bulk water outside a corrosion pit to the site of the metal dissolution. Precipitation of oxides and salts of copper is considered. Studied conditions include water compositions from tap waters to seawater at the temperatures 25 deg C and 75 deg C. Carbonate and sulphate are aggressive towards copper because of complex formation with divalent copper. Carbonate is less aggressive in a corrosion pit than outside at the pH of the bulk. Carbonate carries acidity out from the pit, favours oxide formation and may prevent the initiation of acidic corrosion pits. The concentration profiles are used to estimate the maximum propagation rates for a corrosion pit. A high potential is found to be the most important factor for the rate of propagation. The levels of potential copper can sustain, as corrosion potentials are discussed in terms of the stability of cuprous oxide as a cathode material for oxygen reduction relative to non-conducting cupric phases.

24 CFR 891.740 - Responsibilities of Borrower.

Science.gov (United States)

2010-04-01

... contracting for services are provided in § 891.600(c). (d) Submission of financial and operating statements...) Marketing. (1) The Borrower must commence and continue diligent marketing activities not later than 90 days... homeless in the same housing market. (2) Marketing must be done in accordance with the HUD-approved...

A predictive approach to fitness-for-service assessment of pitting corrosion

International Nuclear Information System (INIS)

Shekari, Elahe; Khan, Faisal; Ahmed, Salim

2016-01-01

Pitting corrosion is a localized corrosion that often causes leak and failure of process components. The aim of this work is to present a new fitness-for-service (FFS) assessment methodology for process equipment to track and predict pitting corrosion. In this methodology, pit density is modeled using a non-homogenous Poisson process and induction time for pit initiation is simulated as the realization of a Weibull process. The non-homogenous Markov process is used to estimate maximum pit depth, considering that only the current state of the damage influences its future development. Subsequently, the distributions of the operating pressure and the estimated burst pressure of the defected component are integrated with Monte Carlo simulations and First Order Second Moment (FOSM) method to calculate the reliability index and probability of failure. This methodology provides a more realistic failure assessment and enables consideration of uncertainty associated with estimating pit characteristics. The practical application of the proposed model is demonstrated using a piping case study. - Highlights: • A new model to estimate maximum pit depth and pit density as two main pit characteristics. • Integrating maximum pit depth with failure analysis considering allowable pressure of defected component. • Time dependent failure analysis to determine the remaining life.

Composição mineral e severidade de "bitter pit" em maçãs 'Catarina' Mineral composition and bitter pit severity in 'Catarina' apples

Directory of Open Access Journals (Sweden)

Cassandro Vidal Talamini do Amarante

2006-04-01

Full Text Available Maçãs 'Catarina', colhidas na maturação comercial em pomar no município de São Joaquim-SC, foram separadas em quatro lotes de 14 frutos, de acordo com a severidade de incidência de "bitter pit": nula (nenhuma lesão/fruto, baixa (1-2 lesões/fruto, moderada (3-5 lesões/fruto e alta (6-18 lesões/fruto. Foram determinadas as concentrações de Ca, Mg, K e N na casca e na polpa de cada fruto. Foram verificadas relação linear (P 'Catarina' apples were harvested at the commercial maturity in an orchard in São Joaquim-SC and segregated in four lots of 14 fruits with different levels of bitter pit severity: null (none pit/fruit, low (1-2 pits/fruit, moderate (3-5 pits/fruit, and high (6-18 pits/fruit. Nutritional analysis (Ca, Mg, K, and N in the skin and flesh tissues were performed on individual fruits of each severity level. The average number of pits/fruit (calculated for each lot of bitter pit severity showed a negative linear relationship (P < 0.05 with the skin Ca content, and a negative linear relationship (P < 0.05 with the ratios of Mg/Ca, (K+Mg/Ca, and (K+Mg+N/Ca in the skin. For the flesh, the increasing of bitter pit severity was accompanied by significant reduction of Ca and Mg contents. The multivariate analysis (canonical discriminant analysis showed that the Mg/Ca ratio in the skin provided the best discrimination between the lots of fruit with different levels of bitter pit severity. Therefore, for 'Catarina' apples, increasing values of the Mg/Ca ratio in the skin are indicative of fruits with increasing bitter pit susceptibility.

Deterministic chaos in the pitting phenomena of passivable alloys

International Nuclear Information System (INIS)

Hoerle, Stephane

1998-01-01

It was shown that electrochemical noise recorded in stable pitting conditions exhibits deterministic (even chaotic) features. The occurrence of deterministic behaviors depend on the material/solution severity. Thus, electrolyte composition ([Cl - ]/[NO 3 - ] ratio, pH), passive film thickness or alloy composition can change the deterministic features. Only one pit is sufficient to observe deterministic behaviors. The electrochemical noise signals are non-stationary, which is a hint of a change with time in the pit behavior (propagation speed or mean). Modifications of electrolyte composition reveals transitions between random and deterministic behaviors. Spontaneous transitions between deterministic behaviors of different features (bifurcation) are also evidenced. Such bifurcations enlighten various routes to chaos. The routes to chaos and the features of chaotic signals allow to suggest the modeling (continuous and discontinuous models are proposed) of the electrochemical mechanisms inside a pit, that describe quite well the experimental behaviors and the effect of the various parameters. The analysis of the chaotic behaviors of a pit leads to a better understanding of propagation mechanisms and give tools for pit monitoring. (author) [fr

Borrowing and Dictionary Compilation: The Case of the Indigenous ...

African Journals Online (AJOL)

rbr

Keywords: BORROWING, DICTIONARY COMPILATION, INDIGENOUS LANGUAGES,. LEXICON, MORPHEME, VOCABULARY, DEVELOPING LANGUAGES, LOAN WORDS, TER-. MINOLOGY, ETYMOLOGY, LEXICOGRAPHY. Opsomming: Ontlening en woordeboeksamestelling: Die geval van in- heemse Suid-Afrikaanse ...

Eastern Scheldt Sand, Baskarp Sand No. 15

DEFF Research Database (Denmark)

Andersen, A. T; Madsen, E. B.; Schaarup-Jensen, A. L.

The present data report contains data from 13 drained triaxial tests, performed on two different sand types in the Soil Mechanics Laboratory at Aalborg University in March, 1997. Two tests have been performed on Baskarp Sand No. 15, which has already ken extensively tested in the Soil Mechanics...... Laboratory. The remaining 11 triaxial tests have ben performed on Eastern Scheldt Sand, which is a material not yet investigated at the Soil Mechanics Laboratory. In the first pari of this data report, the characteristics of the two sand types in question will be presented. Next, a description...... will described. In this connection, the procedure for preparation of the soil specimens will be presented, and the actual performance of the tests will be briefly outlined. Finally, the procedure for processing of the measurements from the laboratory in order to obtain usable data will be described. The final...

Does Consumer Confidence Forecast Household Saving and Borrowing Behavior? Evidence for Poland.

Science.gov (United States)

Kłopocka, Aneta Maria

2017-01-01

Consumer confidence plays an important role in households' decision-making processes. This study investigates the effects of consumer confidence on household saving and borrowing behavior that are unsatisfactorily considered in previous discussions. The questions of interest are first, whether indexes of consumer confidence have any predictive power on their own for future household saving and borrowing rates, and second, whether they contain information about future household saving and borrowing rates aside from the information contained in other available indicators. In addition to aggregate confidence indicators, their components are used to provide more precise information. Overall, the multiple linear regression analysis (OLS technique) of Polish time-series data gives positive answers to both questions. This finding supports the recommendation of combining the strengths of objective indicators (such as economic fundamentals) and subjective indicators (such as consumer confidence) to improve household financial behavior forecasts.

Spontaneous Resolution of Optic Disc Pit Maculopathy

Directory of Open Access Journals (Sweden)

Koushik Tripathy

2017-06-01

Full Text Available I read with interest the article reporting spontaneous resolution of optic disc pit maculopathy in a boy.1 Though the presence of an optic disc pit and associated macular involvement is undoubted in the presented case, the provided optical coherence tomography (OCT does not clearly show typical intraretinal schisis (Figure 1B1 at multiple retinal levels which may communicate with the pit. Instead, it shows a sub-internal limiting membrane (sub-ILM cavity. Such cavities are known to occur following the resolution of sub-ILM bleed due to various cause including Valsalva retinopathy,2 Terson syndrome, and also in some retinitis3 cases.4 In fact, some of these cavities may simulate a neurosensory retinal detachment or central serous chorioretinopathy on cursory clinical examination.5 To confirm that the features of the current patient1 are indeed related to the optic disc pit, it is necessary for the authors to provide an OCT scan which shows a connection of the presented cavity with the optic disc pit. Also, clear OCT scans of the fovea, both at presentation and at final follow-up would help our understanding of the visual recovery of the patient. The interval between the presenting (28 June 2012 OCT and final OCT (30 Nov 2012 is 5 months and not 6 months as described in the manuscript. For an effective comparison, both the presenting and final OCT scans should have been taken using either horizontal or vertical orientation over the macula. Though the spontaneous resolution of optic disc pit maculopathy is possible, visual recovery in usually unlikely and in such cases an alternate diagnosis needs to be excluded.

Liquid waste processing from TRIGA spent fuel storage pits

International Nuclear Information System (INIS)

Buchtela, Karl

1988-01-01

At the Atominstitute of the Austrian Universities and also at other facilities running TRIGA reactors, storage pits for spent fuel elements are installed. During the last revision procedure, the reactor group of the Atominstitute decided to refill the storage pits and to get rid of any contaminated storage pit water. The liquid radioactive waste had been pumped to polyethylene vessels for intermediate storage before decontamination and release. The activity concentration of the storage pit water at the Aominstitute after a storage period of several years was about 40 kBq/l, the total amount of liquid in the storage pits was about 0.25 m 3 . It was attempted to find a simple and inexpensive method to remove especially the radioactive Cesium from the waste solution. Different methods for decontamination like distillation, precipitation and ion exchange are discussed

Investigation of Stress Concentration and Casing Strength Degradation Caused by Corrosion Pits

Directory of Open Access Journals (Sweden)

Wei Yan

2016-01-01

Full Text Available Downhole casing and tubing are subjected to corrosion in many cases because of the exposure to corrosive environment. A more serious problem is that pitting corrosion occurs in the casing inner surface. Meanwhile, downhole strings are subjected to various forms of mechanical loads, for example, internal pressure load, external collapse load, or both. These loads acting on the corrosion pits will cause stress concentration and degrade the casing strength. Thus, it is essential to evaluate the stress concentration degree reasonably. The SCF (stress concentration factor is usually used to characterize the degree of stress concentration induced by corrosion pits. This paper presented a comparison on the SCFs regarding the analytical method for a single pit and experimental method for double pits. The results show that the SCF of a single pit depends mainly on the depth of the corrosion pit; however, the SCF of the double pits strongly depends on the pits distance. A correction factor of 1.3 was recommended in the double pits SCF prediction model.

Speed, Acceleration, Chameleons and Cherry Pit Projectiles

Science.gov (United States)

Planinsic, Gorazd; Likar, Andrej

2012-01-01

The paper describes the mechanics of cherry pit projectiles and ends with showing the similarity between cherry pit launching and chameleon tongue projecting mechanisms. The whole story is written as an investigation, following steps that resemble those typically taken by scientists and can therefore serve as an illustration of scientific…

Considerations when ranking stochastically modeled oil sands resource models for mining applications

Energy Technology Data Exchange (ETDEWEB)

Etris, E.L. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Petro-Canada, Calgary, AB (Canada); Idris, Y.; Hunter, A.C. [Petro-Canada, Calgary, AB (Canada)

2008-10-15

Alberta's Athabasca oil sands deposit has been targeted as a major resource for development. Bitumen recovery operations fall into 2 categories, namely mining and in situ operations. Mining recovery is done above ground level and consists of open pit digging, disaggregation of the bitumen-saturated sediment through crushing followed by pipeline transport in a water-based slurry and then separation of oil, water and sediment. In situ recovery consists of drilling wells and stimulating the oil sands in the subsurface with a thermal treatment to reduce the viscosity of the bitumen and allow it to come to the surface. Steam assisted gravity drainage (SAGD) is the most popular thermal treatment currently in use. Resource models that simulate the recovery process are needed for both mining and in situ recovery operations. Both types can benefit from the advantages of a stochastic modeling process for resource model building and uncertainty evaluation. Stochastic modeling provides a realistic geology and allows for multiple realizations, which mining operations can use to evaluate the variability of recoverable bitumen volumes and develop mine plans accordingly. This paper described the processes of stochastic modelling and of determining the appropriate single realization for mine planning as applied to the Fort Hills oil sands mine which is currently in the early planning stage. The modeling exercise was used to estimate the in-place resource and quantify the uncertainty in resource volumes. The stochastic models were checked against those generated from conventional methods to identify any differences and to make the appropriate adaptations. 13 refs., 3 tabs., 16 figs.

Status of the pit disassembly and conversion facility

International Nuclear Information System (INIS)

Wood, Warren T.; Christensen, Lowell T.

2000-01-01

A planned new facility, the Pit Disassembly and Conversion Facility (PDCF), will be used to disassemble the nation's inventory of surplus nuclear weapons pits and convert the plutonium from those pits into a form suitable for storage, international inspection, and final disposition. Sized to handle 35 metric tons of plutonium from pits and other sources over its 10-year operating life, the PDCF will apply the Advanced Recovery and Integrated Extraction System (ARIES) technology. ARIES process technology has been developed at Los Alamos National Laboratory (LANL) and Lawrence Livermore National Laboratory (LLNL), and an integrated system is being demonstrated at LANL. The Los Alamos National Laboratory is the lead for technical design oversight of the PDCF. Technical data gained from the ARIES demonstrations is integral for the proper design of the PDCF

The role of inclusions in the pitting behaviour of maraging steel

International Nuclear Information System (INIS)

Ahmad, M.S.; Hussain, S.W.; Ashraf, H.

1999-01-01

The pitting characteristics of maraging steel in artificial seawater have been investigated electrochemically using the cyclic polarization technique. Pits were found to be associated with the inclusions present in steel. The hysteresis loop observed indicates that maraging steel has poor resistance to pitting in air saturated seawater. On examination of corroded surfaces under SEM, it is noted that the pits are always associated with inclusions, which are generally the carbonitrides of TiMo presents in maraging steel in varying quantities depending on the melting practice. In order to confirm that the pitting behavior is associated with inclusions, samples from clean maraging steel, having very low inclusion level, were tested. Such samples showed much less tendency for pitting. (author)

Force-displacement measurements of earlywood bordered pits using a mesomechanical tester

Science.gov (United States)

Samuel L. Zelinka; Keith J. Bourne; John C. Hermanson; Samuel V. Glass; Adriana Costa; Alex C. Wiedenhoeft

2015-01-01

The elastic properties of pit membranes are reported to have important implications in understanding air-seeding phenomena in gymnosperms, and pit aspiration plays a large role in wood technological applications such as wood drying and preservative treatment. Here we present force–displacement measurements for pit membranes of circular bordered pits, collected on a...

Investigating oiled birds from oil field waste pits

International Nuclear Information System (INIS)

Gregory, D.G.; Edwards, W.C.

1991-01-01

Procedures and results of investigations concerning the oiling of inland raptors, migratory water-fowl and other birds are presented. Freon washings from the oiled birds and oil from the pits were analyzed by gas chromatography. In most instances the source of the oil could be established by chromatographic procedures. The numbers of birds involved (including many on the endangered species list) suggested the need for netting or closing oil field waste pits and mud disposal pits. Maintaining a proper chain of custody was important

Mature fine tailings from oil sands processing harbour diverse methanogenic communities

Energy Technology Data Exchange (ETDEWEB)

Penner, T.J.; Foght, J.M. [Alberta Univ., Edmonton, AB (Canada). Dept. of Biological Sciences

2010-06-15

Syncrude's bitumen extraction process produces a fine tailings slurry consisting of water, sand, fines, residual bitumen and naphtha diluent. Following rapid settling of the sand fraction, the tailings are stored in large settling ponds to form a thick mature fine tailings (MFT). This paper discussed the potential benefits of methane production on management of the settling basins. Enhanced methanogenesis accelerates densification and improves the rheological properties of MFT. In this study molecular techniques were used to characterize the methanogenic communities in uncultivated MFT samples to determine the diversity present in the Mildred Lake Settling Basin (MLSB) and West In-Pit tailings deposit. The flux of methane is currently estimated at about 40 million L/day at the MLSB. Clone libraries of amplified archaeal and bacterial 16S rRNA genes were created in order to analyze the methanogenic consortia in MFT samples from depth profiles in the 2 tailings deposits. The archaeal sequences, whose closest matches were primarily cultivated methanogens, were comparable within and between basins and were mostly affiliated with acetoclastic Methanosaeta spp. However, bacterial clone libraries were diverse, with most sequences relating to Proteobacteria, including some presumptive nitrate-, iron-, or sulfate-reducing, hydrocarbon-degrading genera. The study showed that MFT consists of a diverse community of prokaryotes that may be responsible for producing methane from substrates indigenous to the MFT. These findings contribute to a better understanding of the biogenesis of methane and densification of MFT in oil sands tailings deposits. The results from this study will help determine strategies to control and exploit microbial activities in these large systems and improve the understanding of methanogenic environments. 43 refs., 2 tabs., 3 figs.

Some questions on small uranium open-pit mines

International Nuclear Information System (INIS)

Li Junyi

1992-01-01

The experiences of the existing uranium open pits are summarized and the questions in design, erection and production are analyzed. It is important helpful to develop and to design such economical and reasonable small uranium open pits

Water and chemical budgets of gravel pit lakes : Case studies of fluvial gravel pit lakes along the Meuse River (The Netherlands) and coastal gravel pit lakes along the Adriatic Sea (Ravenna, Italy)

NARCIS (Netherlands)

Mollema, P.N.

2016-01-01

Gravel pit lakes form when gravel is excavated from below the water table of a phreatic or shallow confined aquifer. Typically many of these lakes are concentrated along naturally occurring sedimentary gravel deposits in areas where gravel is needed for construction. Most gravel pit lakes are

Assessing the effects of oil sands related ozone precursor emissions on ambient ozone levels in the Alberta oil sands region, Canada

Science.gov (United States)

Cho, Sunny; Vijayaraghavan, Krish; Spink, David; Cosic, Biljana; Davies, Mervyn; Jung, Jaegun

2017-11-01

A study was undertaken to determine whether, and the extent to which, increased ground-level ozone (O3) precursor emissions from oil sands development have impacted ambient air quality in the north-eastern Alberta, Canada, over the period 1998 to 2012. Temporal trends in emissions of O3 precursors (NOx and VOC) and ambient air concentrations of O3 precursors, and O3 were examined using the Theil-Sen statistical analysis method. Statistically significant correlations between NOx emissions and ambient NOx concentrations were found mainly near surface (open-pit) mining areas where mine fleets are a large source of NOx emissions. No statistically significant trends in the 4th highest daily maximum 8-hr average O3 at any of the continuous and passive ambient air monitoring stations were found. A significant long-term decrease in monthly averaged O3 is observed at some ambient monitoring sites in summer. A visual examination of long-term variations in annual NOx and VOC emissions and annual 4th highest daily maximum 8-hr O3 concentrations does not reveal any indication of a correlation between O3 concentrations and O3 precursor emissions or ambient levels in the study area. Despite a significant increase in oil sands NOx emissions (8%/yr), there is no statistically significant increase in long-term O3 concentrations at any of monitoring stations considered. This suggests that there is surplus NOx available in the environment which results in a titration of ambient O3 in the areas that have ambient monitoring. The limited ambient O3 monitoring data distant from NOx emission sources makes it impossible to assess the impact of these increased O3 precursor levels on O3 levels on a regional scale. As a precautionary measure, the increasing oil sands development O3 precursor emissions would require that priority be given to the management of these emissions to prevent possible future O3 ambient air quality issues.

Lexical Borrowing in the Speech of First-Generation Hungarian Immigrants in Australia

Directory of Open Access Journals (Sweden)

Anikó Hatoss

2016-09-01

Full Text Available This article reports findings of a sociolinguistic project which investigated language contact phenomena in the speech of first-generation Hungarian Australians living in Sydney. The research aimed to identify and analyze English lexical items borrowed into the spoken Hungarian of first-generation Hungarian–English bilinguals. This research had a mixed methods approach including a quantitative element (count of lexical manifestations by categories such as part of speech and a qualitative element in which the various lexical manifestations have been subjected to a linguistic analysis. The Hungarian National Corpus was used as a reference guide to determine the status of these phenomena in the lexicon of Standard Hungarian. The data were collected through semi-structured sociolinguistic interviews with 22 Hungarian Australians living in Sydney. The findings demonstrate that (a first-generation Hungarians are highly creative language users and integrate a large number of English lexical items into their speech. Most lexical borrowings belong to the derivational blends with the highest proportion of the nominal group. Lexical borrowings from English are morphologically integrated with Hungarian-derivational suffixes and inflectional case markings. This research provides original empirical data to better understand the various inter-language lexical manifestations in Hungarian–English bilingual contexts. The study adds to the relatively small body of research on Hungarian–English bilingualism in diasporic context and contributes to understanding lexical borrowing from a contact linguistic perspective.

Stochastic models for predicting pitting corrosion damage of HLRW containers

International Nuclear Information System (INIS)

Henshall, G.A.

1991-10-01

Stochastic models for predicting aqueous pitting corrosion damage of high-level radioactive-waste containers are described. These models could be used to predict the time required for the first pit to penetrate a container and the increase in the number of breaches at later times, both of which would be useful in the repository system performance analysis. Monte Carlo implementations of the stochastic models are described, and predictions of induction time, survival probability and pit depth distributions are presented. These results suggest that the pit nucleation probability decreases with exposure time and that pit growth may be a stochastic process. The advantages and disadvantages of the stochastic approach, methods for modeling the effects of environment, and plans for future work are discussed

A Bayesian approach to modeling and predicting pitting flaws in steam generator tubes

International Nuclear Information System (INIS)

Yuan, X.-X.; Mao, D.; Pandey, M.D.

2009-01-01

Steam generators in nuclear power plants have experienced varying degrees of under-deposit pitting corrosion. A probabilistic model to accurately predict pitting damage is necessary for effective life-cycle management of steam generators. This paper presents an advanced probabilistic model of pitting corrosion characterizing the inherent randomness of the pitting process and measurement uncertainties of the in-service inspection (ISI) data obtained from eddy current (EC) inspections. A Markov chain Monte Carlo simulation-based Bayesian method, enhanced by a data augmentation technique, is developed for estimating the model parameters. The proposed model is able to predict the actual pit number, the actual pit depth as well as the maximum pit depth, which is the main interest of the pitting corrosion model. The study also reveals the significance of inspection uncertainties in the modeling of pitting flaws using the ISI data: Without considering the probability-of-detection issues and measurement errors, the leakage risk resulted from the pitting corrosion would be under-estimated, despite the fact that the actual pit depth would usually be over-estimated.

Tale of two pit lakes: initial results of a three-year study of the Main Zone and Waterline pit lakes near Houston, British Columbia, Canada

Science.gov (United States)

Crusius, John; Pieters, R.; Leung, A.; Whittle, P.; Pedersen, T.; Lawrence, G.; McNee, J.J.

2003-01-01

Pit lakes are becoming increasingly common in North America as well as in the rest of the world. They are created as openpit mines fill passively with ground water and surface inflows on cessation of mining activity. In many instances, the water quality in these pit lakes does not meet regulatory requirements due to a number of influences. The most important are the oxidation of sulfide minerals and the associated release of acid and metals and the flushing of soluble metals during pit filling. Examples of pit lakes with severe water-quality problems include the Berkeley Pit lake (Butte, MT) and the Liberty Pit lake (Nevada), whose waters are characterized by a pH near 3 and Cu concentrations as high as ~150 mg/L (Miller et al., 1996; Davis and Eary, 1997). The importance of the problem can be seen in the fact that some of these sites in the United States are Superfund sites.

Submarine sand ridges and sand waves in the eastern part of the China Sea

Science.gov (United States)

Wu, Ziyin; Li, Shoujun; Shang, Jihong; Zhou, Jieqiong; Zhao, Dineng; Liang, Yuyang

2016-04-01

Integrated with multi-beam and single-beam echo sounding data, as well as historical bathymetric data, submarine bathymetric maps of the eastern part of the China Sea, including the Bohai Sea, Huanghai Sea, and East China Sea, are constructed to systematically study submarine sand ridges and sand waves in the eastern part of the China Sea, combined with high-resolution seismic, sub-bottom profile and borehole data. Submarine sand ridges are extraordinarily developed in the eastern part of the China Sea, and 7 sand ridge areas can be divided from north to south, that is, the Laotieshan Channel sand ridge area in the Bohai Sea, the Korea Bay sand ridge area in the southern Huanghai Sea, the sand ridge area in the eastern Huanghai islands and the Huanghai Troughs, the Jianggang sand ridge area in the western Huanghai Sea, the sand ridge area in the East China Sea shelf, and the sand ridge and sand wave area in the Taiwan Strait and Taiwan Banks. The distribution area of the sand ridges and sand waves covers more than 450,000 km2, wherein ~10,000 km2 in the Bohai Bay, ~200,000 km2 in the Huanghai Sea, ~200,000 km2 in the East China Sea shelf, and ~40,000 km2 in the Taiwan Strait and Taiwan Banks, respectively. The great mass of sand ridges are distributed within water depth of 5-160 m, with a total length of over 160 km and a main width of 5-10 km. The inner structure of the sand ridges presents features of high-angle inclined beddings, with main lithology of sands, sand-mud alternations partly visible, and a small number of mud cores. Dating results indicate that the sand ridges in the eastern part of the China Sea are mainly developed in the Holocene. Sea-level variation dominates the sand ridge evolution in the eastern part of the China Sea since the LGM, and the sand ridges developed in the area of < 60m water depth are appeared in bad activity, meanwhile sand ridges with good activity are still developed in large scale.

12 CFR 617.7005 - When may electronic communications be used in the borrower rights process?

Science.gov (United States)

2010-01-01

... borrower rights process? Qualified lenders may use, with the parties' agreement, electronic commerce (E-commerce), including electronic communications for borrower rights disclosures. Part 609 of this chapter addresses when a qualified lender may use E-commerce. Consistent with these rules, a qualified lender should...

Modeling sludge accumulation rates in lined pit latrines in slum ...

African Journals Online (AJOL)

Yvonne

should include geo-physical characterization of soil and drainage of pit latrine sites so as ... Key words: Faecal, sludge accumulation rates, slum areas, lined pit latrines. .... Value and its unit Source .... overall quality of the models had to be assessed by validation on ..... Sanitation partnership series: Bringing pit emptying out.

Effect of microcrystallization on pitting corrosion of pure aluminium

International Nuclear Information System (INIS)

Meng Guozhe; Wei Liyan; Zhang Tao; Shao Yawei; Wang Fuhui; Dong Chaofang; Li Xiaogang

2009-01-01

A microcrystalline aluminium film with grain size of about 400 nm was prepared by magnetron sputtering technique. Its corrosion behaviour was investigated in NaCl containing acidic solution by means of potentiodynamic polarization curves and electrochemical noise (EN). The polarization results indicated that the corrosion potential of the sample shifted towards more positive direction, while its corrosion current density decreased compared with that of pure coarse-grain Al. The EN analysis based on stochastic model demonstrated that there existed two kinds of effect of microcrystallization on the pitting behaviour of pure aluminium: (1) the rate of pit initiation is accelerated, (2) the pit growth process was impeded. This leads to the enhancement of pitting resistance for the microcrystallized aluminium.

Constraints on morphological borrowing: evidence from Latin America

NARCIS (Netherlands)

Bakker, D.; Hekking, E.

2012-01-01

In this article, we discuss the borrowing of morphology from Spanish by three unrelated and typologically diffferent American-Indian languages: Quechua, Guarani and Otomi. On the basis of three corpora of spontaneous speech produced by a sizeable number of informants, we will suggest that there are

Pitting and stress corrosion cracking of stainless steel

Science.gov (United States)

Saithala, Janardhan R.

An investigation has been performed to determine the pitting resistance of stainless steels and stress corrosion cracking of super duplex stainless steels in water containing chloride ions from 25 - 170°C. The steels studied are 12% Cr, FV520B, FV566, 304L, Uranus65, 2205, Ferallium Alloy 255, and Zeron 100. All these commercial materials used in very significant industrial applications and suffer from pitting and stress corrosion failures. The design of a new experimental setup using an autoclave enabled potentiodynamic polarisation experiments and slow strain rate tests in dilute environments to be conducted at elevated temperatures. The corrosion potentials were controlled using a three electrode cell with computer controlled potentiostat.The experimental programme to determine pitting potentials was designed to simulate the service conditions experienced in most industrial plants and develop mathematical model equations to help a design engineer in material selection decision. Stress corrosion resistance of recently developed Zeron100 was evaluated in dilute environments to propose a mechanism in chloride solutions at high' temperatures useful for the nuclear and power generation industry. Results have shown the significance of the composition of alloying elements across a wide range of stainless steels and its influence on pitting. Nitrogen and molybdenum added to modern duplex stainless steels was found to be unstable at higher temperatures. The fractographic results obtained using the scanning electron microscope (SEM) has given insight in the initiation of pitting in modem duplex and super duplex stainless steels. A mathematical model has been proposed to predict pitting in stainless steels based on the effect of environmental factors (temperature, chloride concentration, and chemical composition). An attempt has been made to identify the mechanism of SCC in Zeron100 super duplex stainless steel.The proposed empirical models have shown good correlation

Deficit Financing of Schools? The Impact of Statutory Change on School District Borrowing Behavior.

Science.gov (United States)

Edlefson, Carla

In the 70s and 80s, Ohio relaxed its balanced-budget laws to give school districts more options for borrowing over the end of the fiscal year. Two provisions that permit districts to borrow against next year's revenues in order to balance the current year's budget include the Emergency School Advancement program and the Spending Reserve. This…

Why Student Loans Are Different: Findings from Six Focus Groups of Student Loan Borrowers

Science.gov (United States)

Delisle, Jason; Holt, Alexander

2015-01-01

For all the attention student loans have received in the media and from policymakers in recent years, there is still remarkably little information on why and how borrowers struggle to repay them. Rising college prices and debt levels explain some of the troubles borrowers have with their loans, as does a slow economic recovery that has caused…

Laboratory protocols for testing the efficacy of commercial pit latrine ...

African Journals Online (AJOL)

There is considerable national interest in the use of commercial microbially derived products for controlling the rate of accumulation of the contents of pit latrines. Manufacturers claim that some of these products can reduce accumulation rates, prevent the pit from ever filling up, or even result in decreases in pit contents ...

Management of Pit 9 - highlights of accomplishments and lessons learned to date

International Nuclear Information System (INIS)

Schwartz, F.G.

1995-01-01

The Pit 9 project is a U.S. Department of Energy prototype full scale demonstration to retrieve and treat buried mixed transuranic waste. The project is being managed by the DOE-Idaho Environmental Restoration Program, in conjunction with the Environmental Protection Agency Region 10 and the state of Idaho, under the Idaho National Engineering Laboratory Federal Facility Agreement and Consent Order. Pit 9 is located in the northeast corner of the Subsurface Disposal Area (SDA) of the Radioactive Waste Management Complex (RWMC) at the Idaho National Engineering Laboratory (INEL). The Pit 9 project was conceived out of the need to determine capabilities to cost effectively retrieve and treat buried radioactive and radioactive mixed waste, and obtain characterization and contaminant migration data for buried waste at the INEL. Waste was disposed in Pit 9 from November 1967 to June 1969. Pit 9, at about 380 feet by 125 feet, represents approximately one acre of surface area of the 88 acre SDA. The pit contains approximately 350,000 ft 3 of soil beneath and between the buried waste and about 250,000 ft 3 of overburden soil. The average depth of the pit from soil surface to bedrock is approximately 17.5 feet. Approximately 110,000 ft 3 of transuranic (TRU) contaminated mixed wastes from Rocky Flats and approximately 40,000 ft 3 of low level and mixed wastes from the INEL were buried in Pit 9 during this period. Pit 9 is estimated to contain over 30,000 gallons of organics (over 30% of the total organic inventory in the SDA) and approximately 66 pounds of TRU radionuclides (between 3% and 4% of the total TRU inventory in the SDA). Pit 9 was selected as a demonstration site because it was one of the last disposal pits at the INEL to receive Rocky Flats waste, disposal records are better for Pit 9 than for disposal pits and trenches from earlier points in time, and the wastes in Pit 9 are representative of the wastes disposed in the SDA

Pit above the lesser tuberosity in axial view radiography.

Science.gov (United States)

Cho, Jae-Ho; Han, Kyeong-Jin; Lee, Doo-Hyung; Chung, Nam-Su; Park, Do Young

2015-02-01

This study examined the relationship between the presence of a pit above the lesser tuberosity on axial view radiographs and rotator cuff tears and compared the demographic data between groups according to the presence of a pit above the lesser tuberosity. The hypothesis of this study was that the radiographic finding of a pit above the lesser tuberosity is related to rotator cuff tears. For 112 patients with a symptomatic rotator cuff tear, plain radiographs of the symptomatic shoulder (tear side radiographs) and plain radiographs of the asymptomatic contralateral shoulder (no-tear side radiographs) were assessed. Seventeen radiological findings, including a pit above the lesser tuberosity, osteophytes, subchondral cysts, and sclerosis, were recorded by one blinded observer. Demographic data such as age, duration of symptoms, sex, arm dominance, smoking history, trauma history, American Shoulder and Elbow Surgeons score, Constant score, and involved tendon were collected. A pit above the lesser tuberosity was noted on tear side radiographs of 40 patients (35.7 %) and on the no-tear side radiographs of 27 patients (24.1 %), representing a significant difference (P = 0.040). A pit associated with a rotator cuff tear was observed more often in the dominant arm (P = 0.040) and more often in patients with less previous trauma (P = 0.024). A pit above the lesser tuberosity on axial view radiography was associated with a rotator cuff tear and occurred more often in the dominant arm of patients who had no trauma history. Prognostic study, Level III.

34 CFR 674.42 - Contact with the borrower.

Science.gov (United States)

2010-07-01

... debt is owed and the name and address of the official or servicing agent to whom communications should... person, by audiovisual presentation, or by interactive electronic means. The institution must ensure that... law, and litigation; (viii) Emphasize that the borrower is obligated to repay the full amount of the...

The phylogenetic significance of vestured pits in Boraginaceae

NARCIS (Netherlands)

Rabaey, D.; Lens, F.; Smets, E.; Jansen, S.

2010-01-01

The bordered pit structure in tracheary elements of 105 Boraginaceae species is studied using scanning electron microscopy to examine the systematic distribution of vestured pits. Forty-three species out of 16 genera show a uniform presence of this feature throughout their secondary xylem. Most

Structural evaluation of W-211 flexible receiver platforms and tank pit walls

International Nuclear Information System (INIS)

Shrivastava, H.P.

1997-01-01

This document is a structural analysis of the Flexible Receiver Platforms and the tank-pit wall during removal of equipment and during a accidental drop of that equipment. The platform and the pit walls must withstand a accidental drop of a mixer and transfer pumps in specific pits in tanks 102-AP and 104-AP. A mixer pump will be removed from riser 11 in pit 2A on tank 241-AP-102. A transfer pump will be removed from riser 13 in pit 2D on tank 241-AP-102 and another transfer pump will be removed from riser 3A in pit 4A on tank 241-AP-104

Does Discretion in Lending Increase Bank Risk? Borrower Self-Selection and Loan Officer Capture Effects

NARCIS (Netherlands)

Gropp, R.; Grundl, C.; Guttler, A.

2012-01-01

Abstract: In this paper we analyze whether discretionary lending increases bank risk. We use a panel dataset of matched bank and borrower data. It offers the chief advantages that we can directly identify soft information in banks’ lending decisions and that we observe ex post defaults of borrowers.

Does Discretion in Lending Increase Bank Risk? Borrower Self-Selection and Loan Officer Capture Effects

NARCIS (Netherlands)

Gropp, R.; Grundl, C.; Guttler, A.

2012-01-01

In this paper we analyze whether discretionary lending increases bank risk. We use a panel dataset of matched bank and borrower data. It offers the chief advantages that we can directly identify soft information in banks’ lending decisions and that we observe ex post defaults of borrowers.Consistent

34 CFR 682.301 - Eligibility of borrowers for interest benefits on Stafford and Consolidation loans.

Science.gov (United States)

2010-07-01

... Stafford and Consolidation loans. 682.301 Section 682.301 Education Regulations of the Offices of the... borrowers for interest benefits on Stafford and Consolidation loans. (a) General. (1) To qualify for benefits on a Stafford loan, a borrower must demonstrate financial need in accordance with Part F of the...

13 CFR 120.712 - How does an Intermediary get a grant to assist Microloan borrowers?

Science.gov (United States)

2010-01-01

... contribution. It may only use grant funds to provide Microloan borrowers with marketing, management, and... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false How does an Intermediary get a grant to assist Microloan borrowers? 120.712 Section 120.712 Business Credit and Assistance SMALL...

ON THE PROPAGATION OF OPEN AND COVERED PIT IN 316L STAINLESS STEEL

International Nuclear Information System (INIS)

Heurtault, Stéphane; Robin, Raphaël; Rouillard, Fabien; Vivier, Vincent

2016-01-01

Highlights: • The propagation of a single pit was investigated with a flow micro-device. • Both in depth and radial pit propagation were characterized. • The formation of a salt film in the pit was discussed. - Abstract: Pitting corrosion on stainless steel has been widely studied during the last decades, but since it is a stochastic process, it remains difficult to analyze experimentally such a phenomenon. In this work, reproducible single pits were performed on 316L steel by using an experimental setup based on the use of a glass microcapillary to locally supply chloride ions on the steel surface in order to characterize the pit propagation. This original approach allowed obtaining new results about pit propagation. Indeed, it was possible to control the presence of a metallic cap covering the pit by adjusting the experimental parameters (potential – chloride to sulfate ratio – temperature). The presence of this cover was shown to be an important issue concerning the propagation mechanism. It was also possible to study the evolution of both the pit depth and the pit diameter as a function of various parameters. Then, based on the simulation of the current densities at the pit bottom and at the pit aperture, a special attention has been paid for the investigation of the local propagation mechanism.

Fontainebleau Sand

DEFF Research Database (Denmark)

Leth, Caspar Thrane

2006-01-01

The report is a summary of results from laboratory tests in the geotechncial research group on Fontainebleau sand.......The report is a summary of results from laboratory tests in the geotechncial research group on Fontainebleau sand....

Studies in pitting corrosion on archaeological bronzes. Copper

International Nuclear Information System (INIS)

Bresle, Aa.; Saers, J.; Arrhenius, B.

1983-01-01

Copper has been proposed as a canister material for use in the long-term storage of radioactive waste from nuclear power reactors. The storage period has been set to at least 100 000 years, during which time the copper cylinders must remain intact so that the contained waste has no possibility of leaking out. In this work, the pitting factor in archaelogical copper objects have been determined. The absolute values of the pitting factor obtained are generally very low. In the case of the most thoroughly studied material the pitting factor is only slightly more than three units. Nor does the native copper, with a presumed burial period of about 8000 years, exhibit particularly high values. In summary, it can therefore be concluded that the present study does not provide support for the assumption of extremely high pitting factors in copper-base material that has been buried for periods of several millenia. (G.B.)

PITTING CORROSION OF STAINLESS STEEL AT THE VARIOUS SURFACE TREATMENT

Directory of Open Access Journals (Sweden)

Viera Zatkalíková

2011-09-01

Full Text Available The stainless steel surface treatment is very important with regard to its pitting corrosion susceptibility. An effect of various types surfacing on pitting corrosion resistance of AISI 304stainless steel is investigated in this work. The samples of the tested material are turned, blasted, peened, grinded and a half of them are pickled to achieve higher purity of surfaces and better quality of passive film. Eight types of different finished surfaces are tested by electrochemical and immersion tests to determine corrosion behaviour in conditions where pitting is evoked by controlled potential and second by solution with high redox potential. By this way the effect of mechanical and chemical surface treatment on the resistance to pitting corrosion, character, size and shape of pits are compared in the conditions of different mechanisms of corrosion process.

Congenital pits of the optic nerve head and retinochoroidal colobomas.

Science.gov (United States)

Brown, G C; Augsburger, J J

1980-07-01

A 45-year-old man presented with bilateral retinochoroidal colobomas associated with an inferonasal congenital pit of the optic nerve head in each eye. Different theories on the origin of such pits are discussed. This case supports the theory that some congenital optic pits occur as a result of failure of closure of the superior end of the embryonic fissure.

Lexical Borrowings in Spanish: Function, Length, Genealogy and Chronology.

Science.gov (United States)

Patterson, William T.

1986-01-01

A study reveals that lexical borrowing in Spanish, from a variety of languages including Latin, French, Italian, Greek, Arabic, Provencal, and Catalan, accounts for 41 percent of the basic Spanish vocabulary, with variation in source according to historical period. (MSE)

Effects of selected water chemistry variables on copper pitting propagation in potable water

International Nuclear Information System (INIS)

Ha Hung; Taxen, Claes; Williams, Keith; Scully, John

2011-01-01

Highlights: → The effects of water composition on pit propagation kinetics on Cu were separated from pit initiation and stabilization using the artificial pit method in a range of dilute HCO 3 - , SO 4 2- and Cl - -containing waters. → The effective polarization and Ohmic resistance of pits were lower in SO4 2- -containing solutions and greater in Cl - -containing solutions. → Relationship between the solution composition and the corrosion product identity and morphology were found. → These, in turn controlled the corrosion product Ohmic resistance and subsequently the pit growth rate. - Abstract: The pit propagation behavior of copper (UNS C11000) was investigated from an electrochemical perspective using the artificial pit method. Pit growth was studied systematically in a range of HCO 3 - , SO 4 2- and Cl - containing-waters at various concentrations. Pit propagation was mediated by the nature of the corrosion products formed both inside and over the pit mouth (i.e., cap). Certain water chemistry concentrations such as those high in sulfate were found to promote fast pitting that could be sustained over long times at a fixed applied potential but gradually stifled in all but the lowest concentration solutions. In contrast, Cl - containing waters without sulfate ions resulted in slower pit growth and eventual repassivation. These observations were interpreted through understanding of the identity, amount and porosity of corrosion products formed inside and over pits. These factors controlled their resistive nature as characterized using electrochemical impedance spectroscopy. A finite element model (FEM) was developed which included copper oxidation kinetics, transport by migration and diffusion, Cu(I) and Cu(II) solid corrosion product formation and porosity governed by equilibrium thermodynamics and a saturation index, as well as pit current and depth of penetration. The findings of the modeling were in good agreement with artificial pit experiments

Microstructural evolution and pitting resistance of annealed lean duplex stainless steel UNS S32304

International Nuclear Information System (INIS)

Zhang Ziying; Han Dong; Jiang Yiming; Shi Chong; Li Jin

2012-01-01

Highlights: ► The relationship between pitting corrosion resistance and annealing temperature for UNS S32304 was systemically studied. ► The specimens annealed at 1080 °C for 1 h, quenched in water exhibit the best pitting corrosion resistance. ► The relationship between microstructural evolution and pitting resistance of annealed UNS S32304 was discussed in detail. ► The pitting corrosion resistance is consistent with pitting resistance equivalent number of weaker phase for UNS S32304 alloy. - Abstract: The effect of annealing temperature in the range from 1000 to 1200 °C on the pitting corrosion behavior of duplex stainless steel UNS S32304 was investigated by the potentiodynamic polarization and potentiostatic critical pitting temperature techniques. The microstructural evolution and pit morphologies were studied using a scanning electron microscopy with energy dispersive X-ray spectroscopy. The results demonstrated that the nucleation of metastable pits transformed from austenite phase to ferrite phase with the increasing annealing temperature. As the annealing temperature increased, the pitting corrosion resistance firstly increased and then decreased. The highest pitting corrosion resistance was obtained at 1080 °C with the highest critical pitting temperature value and pitting nucleation resistance. The results could be well explained by the microstructural evolution of ferrite and austenite phases induced by annealing treatment.

Take the money and run: making profits by paying borrowers to stay home

OpenAIRE

Coco, Giuseppe; De Meza, David; Pignataro, Giuseppe; Reito, Francesco

2013-01-01

Can a bank increase its profit by subsidizing inactivity? This paper suggests this may occur, due to the presence of hidden information, in a monopolistic credit market. Rather than offering credit in a pooling contract, a monopolist bank can sort borrowers through an appropriate subsidy to inactivity. Under some conditions, sorting may avoid the collapse of the market and increases the welfare of everybody. The bank increases its profits, good borrowers benefit from lower interest rates and ...

The Cost of Collateralized Borrowing in the Colombian Money Market: Does Connectedness Matter?

OpenAIRE

Constanza Martínez; Carlos León

2014-01-01

Under the view that the market is a weighted and directed network (Barabási, 2003), this document is a first attempt to model the Colombian money market within a spatial econometrics framework. By estimating two standard spatial econometric models, we study the cost of collateralized borrowing (i.e. sell/buy backs) among Colombian financial institutions, and its relationship with the effects induced by traditional variables (leverage, size and borrowing levels), and by spatial variables resul...

Pitting growth rate in carbon steel exposed to simulated radioactive waste

International Nuclear Information System (INIS)

Zapp, P.E.

1995-01-01

Dilute high-level radioactive waste slurries can induce pitting corrosion in carbon steel tanks in which such waste is stored and processed. The waste is normally maintained with closely monitored nitrite and hydroxide concentrations known to prevent the initiation of pitting. Coupon immersion are being conducted in laboratory simulants of waste to determine the probability and growth rate of pitting in steel in the event of below-limits nitrite concentrations. Sets of about 36 carbon steel coupons have been immersed in known corrosive conditions (nitrite < 5% of the established limit) at a temperature of 50 C. Three sets have been removed from testing after 64, 150, and 350 days of immersion. The long immersion times introduced variability in the exposure conditions due to the evaporation and replenishment of solution. The deepest corrosive attack was measured one each coupon by optical microscopy. The deepest pits were ranked and analyzed as a type 1 extreme value distribution to extrapolate from the coupon population to the maximum pit depths in a waste tank structure. The data were compared to a power law for pit growth, although the deepest pits did not increase monotonically with time in the limited data set

Alberta oil sands crudes : upgrading and marketing

International Nuclear Information System (INIS)

Ashar, M.

2008-01-01

Open pit mining and in situ techniques, such as steam stimulation, are used to recover Alberta's bitumen and heavy oil resources, which have higher viscosities than conventional hydrocarbons. The bitumen is typically upgraded to synthetic crude oil (SCO). In the simplest processing scheme, the bitumen is blended with diluent for ease in pipeline transport and then processed at refineries with upgrading facilities. The bitumen is also upgraded to light SCO at world-scale upgraders in Alberta. The SCO is then processed at refineries in downstream markets. The 2 categories of upgrading, notably primary and secondary upgrading, were described in this article along with technology options for both categories. Slurry hydrocracking is regarded as the most interesting emerging residual fuel upgrading technology. It combines special catalyst mixes with the latest slurry reactor designs as well as innovative catalyst capture and recycle schemes to produce very high conversions and potentially superior upgrading economics. The increase in volume and rate of SCO from Alberta provides refiners in the oil sands marketing sector an unprecedented choice of opportunities to improve profitability. Key trends indicate that production will increase substantially from 2008 to 2030. 5 figs

Alberta oil sands crudes : upgrading and marketing

Energy Technology Data Exchange (ETDEWEB)

Ashar, M. [Suncor Energy, Fort McMurray, AB (Canada)

2008-05-15

Open pit mining and in situ techniques, such as steam stimulation, are used to recover Alberta's bitumen and heavy oil resources, which have higher viscosities than conventional hydrocarbons. The bitumen is typically upgraded to synthetic crude oil (SCO). In the simplest processing scheme, the bitumen is blended with diluent for ease in pipeline transport and then processed at refineries with upgrading facilities. The bitumen is also upgraded to light SCO at world-scale upgraders in Alberta. The SCO is then processed at refineries in downstream markets. The 2 categories of upgrading, notably primary and secondary upgrading, were described in this article along with technology options for both categories. Slurry hydrocracking is regarded as the most interesting emerging residual fuel upgrading technology. It combines special catalyst mixes with the latest slurry reactor designs as well as innovative catalyst capture and recycle schemes to produce very high conversions and potentially superior upgrading economics. The increase in volume and rate of SCO from Alberta provides refiners in the oil sands marketing sector an unprecedented choice of opportunities to improve profitability. Key trends indicate that production will increase substantially from 2008 to 2030. 5 figs.

Acidic pit lakes. The legacy of coal and metal surface mines

Energy Technology Data Exchange (ETDEWEB)

Geller, Walter; Schultze, Martin [Helmholtz Centre for Environmental Research - UFZ, Magdeburg (Germany); Wolkersdorfer, Christian (eds.) [Cape Breton Univ., Sydney, NS (Canada). Industrial Research Chair in Mine Water Remediation and Management; International Mine Water Association, Wendelstein (Germany). General Secretary; Kleinmann, Robert

2013-07-01

This monograph provides an international perspective on pit lakes in post-mining landscapes, including the problem of geogenic acidification. Much has been learned during the last decade through research and practical experience on how to mitigate or remediate the environmental problems of acidic pit lakes. In the first part of the book, general scientific issues are presented in 21 contributions from the fields of geo-environmental science, water chemistry, lake physics, lake modeling, and on the peculiar biological features that occur in the extreme habitats of acidic pit lakes. Another chapter provides an overview of methods currently used to remediate acidic pit lakes and treat outflowing acidic water. The second part of the book is a collection of regional surveys of pit lake problems from three European countries and Australia, and case studies of various individual representative lakes. A final case study provides an innovative approach to assessing the economic value of new pit lakes and balancing the costs and benefits, a valuable tool for decision makers.

Stochastic modeling of pitting corrosion in underground pipelines using Markov chains

Energy Technology Data Exchange (ETDEWEB)

Velazquez, J.C.; Caleyo, F.; Hallen, J.M.; Araujo, J.E. [Instituto Politecnico Nacional (IPN), Mexico D.F. (Mexico). Escuela Superior de Ingenieria Quimica e Industrias Extractivas (ESIQIE); Valor, A. [Universidad de La Habana, La Habana (Cuba)

2009-07-01

A non-homogenous, linear growth (pure birth) Markov process, with discrete states in continuous time, has been used to model external pitting corrosion in underground pipelines. The transition probability function for the pit depth is obtained from the analytical solution of the forward Kolmogorov equations for this process. The parameters of the transition probability function between depth states can be identified from the observed time evolution of the mean of the pit depth distribution. Monte Carlo simulations were used to predict the time evolution of the mean value of the pit depth distribution in soils with different physicochemical characteristics. The simulated distributions have been used to create an empirical Markov-chain-based stochastic model for predicting the evolution of pitting corrosion from the observed properties of the soil in contact with the pipeline. Real- life case studies, involving simulated and measured pit depth distributions are presented to illustrate the application of the proposed Markov chains model. (author)

Pitting corrosion of Inconel 600 in chloride and sulfate solutions at low temperature

International Nuclear Information System (INIS)

Chang Mingyu; Yu Geping

1993-01-01

Pitting corrosion of Inconel 600 was examined in chloride and sulfate solutions through usage of potentiodynamic polarization techniques. The effects of chloride and sulfate concentration were investigated in the range of 0.0001 to 0.1 M. Increasing chloride concentrations resulted in active shifts of the pit nucleation potential. Immunity to pitting corrosion was evident at a chloride level below 0.005 M. Increasing sulfate concentrations resulted in improved pitting resistance of Inconel 600 in chloride solutions. Detrimental effects associated with pitting were evident with low-level sulfate being added to dilute chloride media. The density of pits increased with increasing chloride concentrations or temperature between room temperature and 70 C. Systematic trends for the depth of pits were not evident. The observations of pitting corrosion in open immersion were consistent with those in polarization methods. Corrosion products contained in the pits were enriched in nickel, chromium and iron with a small amount of titanium and silicon. The enrichment of chlorine or sulfur was still, however, not found. (orig.)

Numerical modelling of the groundwater inflow to an advancing open pit mine: Kolahdarvazeh pit, Central Iran.

Science.gov (United States)

Bahrami, Saeed; Doulati Ardejani, Faramarz; Aslani, Soheyla; Baafi, Ernest

2014-12-01

The groundwater inflow into a mine during its life and after ceasing operations is one of the most important concerns of the mining industry. This paper presents a hydrogeological assessment of the Irankuh Zn-Pb mine at 20 km south of Esfahan and 1 km northeast of Abnil in west-Central Iran. During mine excavation, the upper impervious bed of a confined aquifer was broken and water at high-pressure flowed into an open pit mine associated with the Kolahdarvazeh deposit. The inflow rates were 6.7 and 1.4 m(3)/s at the maximum and minimum quantities, respectively. Permeability, storage coefficient, thickness and initial head of the fully saturated confined aquifer were 3.5 × 10(-4) m/s, 0.2, 30 m and 60 m, respectively. The hydraulic heads as a function of time were monitored at four observation wells in the vicinity of the pit over 19 weeks and at an observation well near a test well over 21 h. In addition, by measuring the rate of pumping out from the pit sump, at a constant head (usually equal to height of the pit floor), the real inflow rates to the pit were monitored. The main innovations of this work were to make comparison between numerical modelling using a finite element software called SEEP/W and actual data related to inflow and extend the applicability of the numerical model. This model was further used to estimate the hydraulic heads at the observation wells around the pit over 19 weeks during mining operations. Data from a pump-out test and observation wells were used for model calibration and verification. In order to evaluate the model efficiency, the modelling results of inflow quantity and hydraulic heads were compared to those from analytical solutions, as well as the field data. The mean percent error in relation to field data for the inflow quantity was 0.108. It varied between 1.16 and 1.46 for hydraulic head predictions, which are much lower values than the mean percent errors resulted from the analytical solutions (from 1.8 to 5

7 CFR 1717.657 - Investments above the 15 percent level by certain borrowers not exempt under § 1717.656(a).

Science.gov (United States)

2010-01-01

... plant. (d) Distribution and power supply borrowers. If the aggregate of the investments, loans and... investment controls under § 1717.656(a) may not make investments, loans and guarantees in an aggregate amount... (d) of this section.) (c) Power supply borrowers. (1) Power supply borrowers not exempt from RUS...

Study of Black Sand Particles from Sand Dunes in Badr, Saudi Arabia Using Electron Microscopy

Directory of Open Access Journals (Sweden)

Haider Abbas Khwaja

2015-08-01

Full Text Available Particulate air pollution is a health concern. This study determines the microscopic make-up of different varieties of sand particles collected at a sand dune site in Badr, Saudi Arabia in 2012. Three categories of sand were studied: black sand, white sand, and volcanic sand. The study used multiple high resolution electron microscopies to study the morphologies, emission source types, size, and elemental composition of the particles, and to evaluate the presence of surface “coatings or contaminants” deposited or transported by the black sand particles. White sand was comprised of natural coarse particles linked to wind-blown releases from crustal surfaces, weathering of igneous/metamorphic rock sources, and volcanic activities. Black sand particles exhibited different morphologies and microstructures (surface roughness compared with the white sand and volcanic sand. Morphological Scanning Electron Microscopy (SEM and Laser Scanning Microscopy (LSM analyses revealed that the black sand contained fine and ultrafine particles (50 to 500 nm ranges and was strongly magnetic, indicating the mineral magnetite or elemental iron. Aqueous extracts of black sands were acidic (pH = 5.0. Fe, C, O, Ti, Si, V, and S dominated the composition of black sand. Results suggest that carbon and other contaminant fine particles were produced by fossil-fuel combustion and industrial emissions in heavily industrialized areas of Haifa and Yanbu, and transported as cloud condensation nuclei to Douf Mountain. The suite of techniques used in this study has yielded an in-depth characterization of sand particles. Such information will be needed in future environmental, toxicological, epidemiological, and source apportionment studies.

A cost comparison study of open pit mining vs. in situ assisted gravity drainage

International Nuclear Information System (INIS)

McIntosh, J.; Luhning, R.W.

1991-01-01

The twin-well steam assisted gravity drainage (SAGD) process has resulted in breakthrough technology to access previously uneconomical deep-seated oil sands reserves in Alberta, and to provide a very cost-effective and environmentally acceptable method for extracting bitumen from reserves having a minimum of 30 m overburden. In the evaluation of new or improved bitumen recovery technologies for its new North Mine, Syncrude Canada has recognized that SAGD was a potential alternate to the current open pit mining and hot water extraction process. A study was conducted to compare and evaluate bitumen recovery by the two schemes at the North Mine site, scheduled to begin operations in 1996, for the reserves under Syncrude's tailings pond, and at a new grassroots area. Study description and analysis of results are presented for the grassroots case. The assumptions and mining/recovery processes used for the mining or SAGD method are detailed and the advantages and drawbacks of each scheme are noted. Results show that the SAGD unit supply costs are projected to be proportionately lower than the corresponding open pit mining/hot water extraction (OP/X) cost, using a 20-y project life. A sensitivity analysis indicates that the SAGD process is more sensitive to natural gas costs, while the OP/X scheme is more sensitive to power costs. The SAGD process is much less labor-intensive than OP/X and has obvious advantages in terms of tailings disposal and post-mining reclamation. In addition, the underground nature of SAGD operation eliminates adverse effects of the weather on working conditions. 11 figs

Development of orgware of borrower - legal entity’s solvency analysis

Directory of Open Access Journals (Sweden)

Vygovska N.G.

2017-03-01

Full Text Available The article is devoted to the development of orgware of borrower - legal entity’s solvency analysis. The authors investigate the orgware of solvency estimation mechanism in two aspects: 1 as the aggregate of the organizational stages of solvency estimation; 2 as an organizational structure and co-operation between different structural subdivisions of bank. The paper itemizes and specifies the stages of orgware of borrower - legal entity’s solvency analysis according to such signs as the purpose of the stage; responsible for the stage; the issues studied on the stage; documenting, duration and features of the organizational stage. The documentary providing of the process organization of solvency analysis is improved, namely, the appendix to executive Summary «Estimation of off-balance sheet obligations (off-balance sheet risks of borrower on the project credited» is offered. The authors’ attention is paid to the existence (in international practice of two methods of organization process of enterprises-borrowers’ rating: 1 oriented to the external rating and 2 oriented to the internal rating, their advantages and disadvantages are identified. The article offers the algorithm of informative co-operation of basic subjects of borrower’s solvency analysis after the selected organizational stages at forming of the internal credit rating, which will be instrumental in the improvement of process of enterprises’ crediting, standardization of procedure, and decline of crediting risks.

Clinico epidemiological study of pitted keratolysis

Directory of Open Access Journals (Sweden)

Naik Chandra

2007-01-01

Full Text Available Background: Pitted keratolysis is a common dermatological condition. However, very few studies are available on the clinical characteristics and epidemiological features of this disorder from India and abroad. Materials and Methods: Fifty patients from rural area of Kolar at Sri R.L.J.H. and S.N.R. Hospital, presenting with clinically distinctive lesions of pitted keratolysis were included in the study. Cases were interviewed with particular emphasis on triggering factors and findings were recorded. Investigations like Gram′s stain, culture studies, Wood′s ultraviolet light examination, histopathology etc, was done in selected cases to ascertain the clinical diagnosis. Results: Age of the patients varied from 20 to 40 years in 52% with male preponderance in 82% of cases. Duration of the disease varied from 15 days to five years, most of the patients were bare-footed farmers (62% of cases. Hyperhidrosis and pruritus were most frequently observed symptoms in 70% and 60% of patients. Most of the patients presented with the characteristic pits which varied from 1 to 50 in number in 56 % of cases, located predominantly on the pressure bearing areas in 92% of cases and depth of the pits varied from 1 to 2 mm in 60% of cases. Associated skin conditions recorded in present study were fissuring of soles in 38%, psoriasis 10%, dermatophyte infections in 6%, planter warts 6% and Corynebacterial triad and corn in 2% of patients each. Discussion: Affection of bare-footed individuals, male preponderance, presence of hyperhidrosis and occurrence of lesions over pressure bearing areas of soles, observed in the present study were consistent with earlier studies on the subject. However, pruritus as commonest presenting symptom reported by 60% patients in the present study, has not been documented in the previous studies. Conclusion: Pitted keratolysis is fairly common in bare footed male farmers of rural India. The condition is predominantly seen over the

Corrosion pit depth extreme value prediction from limited inspection data

International Nuclear Information System (INIS)

Najjar, D.; Bigerelle, M.; Iost, A.; Bourdeau, L.; Guillou, D.

2004-01-01

Passive alloys like stainless steels are prone to localized corrosion in chlorides containing environments. The greater the depth of the localized corrosion phenomenon, the more dramatic the related damage that can lead to a structure weakening by fast perforation. In practical situations, because measurements are time consuming and expensive, the challenge is usually to predict the maximum pit depth that could be found in a large scale installation from the processing of a limited inspection data. As far as the parent distribution of pit depths is assumed to be of exponential type, the most successful method was found in the application of the statistical extreme-value analysis developed by Gumbel. This study aims to present a new and alternative methodology to the Gumbel approach with a view towards accurately estimating the maximum pit depth observed on a ferritic stainless steel AISI 409 subjected to an accelerated corrosion test (ECC1) used in automotive industry. This methodology consists in characterising and modelling both the morphology of pits and the statistical distribution of their depths from a limited inspection dataset. The heart of the data processing is based on the combination of two recent statistical methods that avoid making any choice about the type of the theoretical underlying parent distribution of pit depths: the Generalized Lambda Distribution (GLD) is used to model the distribution of pit depths and the Bootstrap technique to determine a confidence interval on the maximum pit depth. (authors)

Statistical characterization of pitting corrosion process and life prediction

International Nuclear Information System (INIS)

Sheikh, A.K.; Younas, M.

1995-01-01

In order to prevent corrosion failures of machines and structures, it is desirable to know in advance when the corrosion damage will take place, and appropriate measures are needed to mitigate the damage. The corrosion predictions are needed both at development as well as operational stage of machines and structures. There are several forms of corrosion process through which varying degrees of damage can occur. Under certain conditions these corrosion processes at alone and in other set of conditions, several of these processes may occur simultaneously. For a certain type of machine elements and structures, such as gears, bearing, tubes, pipelines, containers, storage tanks etc., are particularly prone to pitting corrosion which is an insidious form of corrosion. The corrosion predictions are usually based on experimental results obtained from test coupons and/or field experiences of similar machines or parts of a structure. Considerable scatter is observed in corrosion processes. The probabilities nature and kinetics of pitting process makes in necessary to use statistical method to forecast the residual life of machine of structures. The focus of this paper is to characterization pitting as a time-dependent random process, and using this characterization the prediction of life to reach a critical level of pitting damage can be made. Using several data sets from literature on pitting corrosion, the extreme value modeling of pitting corrosion process, the evolution of the extreme value distribution in time, and their relationship to the reliability of machines and structure are explained. (author)

A formal account of the interaction of orthography and perception : English intervocalic consonants borrowed into Italian

NARCIS (Netherlands)

Hamann, S.; Colombo, I.E.

This study presents a formal generative model that integrates perception and reading, and uses English intervocalic consonants borrowed into Italian as either singletons or geminates to illustrate how the model works. Consisting of words borrowed in the 20th century, our data show that the quantity

Template measurement for plutonium pit based on neural networks

International Nuclear Information System (INIS)

Zhang Changfan; Gong Jian; Liu Suping; Hu Guangchun; Xiang Yongchun

2012-01-01

Template measurement for plutonium pit extracts characteristic data from-ray spectrum and the neutron counts emitted by plutonium. The characteristic data of the suspicious object are compared with data of the declared plutonium pit to verify if they are of the same type. In this paper, neural networks are enhanced as the comparison algorithm for template measurement of plutonium pit. Two kinds of neural networks are created, i.e. the BP and LVQ neural networks. They are applied in different aspects for the template measurement and identification. BP neural network is used for classification for different types of plutonium pits, which is often used for management of nuclear materials. LVQ neural network is used for comparison of inspected objects to the declared one, which is usually applied in the field of nuclear disarmament and verification. (authors)

Cormorant predation on PIT-tagged lake fish

DEFF Research Database (Denmark)

Skov, Christian; Jepsen, Niels; Baktoft, Henrik

2014-01-01

The present study use data from recovered PIT (Passive Integrated Transponder) tags to explore species-and size-specific annual predation rates by cormorants on three common lacustrine fishes (size range 120-367 mm) in a European lake; roach (Rutilus rutilus), common bream (Abramis brama) and perch...... (Perca fluviatilis). In addition, we quantify the level of age/size truncation that cormorant predation could introduce in a population of perch, an important fish for recreational angling as well as for trophic interactions and ecosystem function in European lakes. Based on three years of PIT tagging...... of fish in Lake Viborg and subsequent recoveries of PIT tags from nearby cormorant roosting and breeding sites, we show that cormorants are major predators of roach, bream and perch within the size groups we investigated and for all species larger individuals had higher predation rates. Perch appear...

WORKSHOP ON THE CHARACTERIZATION, MODELING, REMEDIATION AND MONITORING OF MINING-IMPACTED PIT LAKES, SANDS RGENCY CASINO HOTEL, DOWNTOWN RENO, NV. APRIL 4-6, 2000 (PROGRAM FLYER)

Science.gov (United States)

The purpose of this workshop is to provide a forum for the exchange of scientific infomation on current approaches for assessing the characterization, monitoring, treatment and/or remediation of impacts on aquatic ecosystems including pit lakes from mining-related contamination i...

Metallography of pitted aluminum-clad, depleted uranium fuel

International Nuclear Information System (INIS)

Nelson, D.Z.; Howell, J.P.

1994-01-01

The storage of aluminum-clad fuel and target materials in the L-Disassembly Basin at the Savannah River Site for more than 5 years has resulted in extensive pitting corrosion of these materials. In many cases the pitting corrosion of the aluminum clad has penetrated in the uranium metal core, resulting in the release of plutonium, uranium, cesium-137, and other fission product activity to the basin water. In an effort to characterize the extent of corrosion of the Mark 31A target slugs, two unirradiated slug assemblies were removed from basin storage and sent to the Savannah River Technology Center for evaluation. This paper presents the results of the metallography and photographic documentation of this evaluation. The metallography confirmed that pitting depths varied, with the deepest pit found to be about 0.12 inches (3.05 nun). Less than 2% of the aluminum cladding was found to be breached resulting in less than 5% of the uranium surface area being affected by corrosion. The overall integrity of the target slug remained intact

The kinetics of pitting corrosion of carbon steel

International Nuclear Information System (INIS)

Marsh, G.P.; Taylor, K.J.; Sooi, Z.

1988-02-01

The development of an improved statistical method for analysing pit growth data to take account of the difference in area of laboratory specimens and full sized high level nuclear waste containers is described. Statistical analysis of data from pit growth experiments with large area (460 cm 2 ) plates of BS 4360 steel have indicated that the depth distributions correlate most closely with a limited distribution function. This correlation implies that previous statistical analyses to estimate the maximum pit depths in full size containers, which were made using unlimited distribution functions, will be pessimistic. An evaluation of the maximum feasible pitting period based on estimating the period during which the oxygen diffusion flux is sufficient to stabilise a passive film on carbon steel containers has indicated that this is of the order of 125 years rather than the full 1000 year container life. The estimate is sensitive to the value of the leakage current assumed to flow through the passive film, and therefore work is planned to measure this accurately in relevant granitic environments. (author)

RCRA closure plan for the Bear Creek Burial Grounds B Area and Walk- In Pits at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1993-01-01

In June 1987, the RCRA Closure/Postclosure Plan for the Bear Creek Burial Grounds (BCBG) was submitted to the Tennessee Department of Environment and Conservation (TDEC) for review and approval. TDEC modified and issued the plan approved on September 30, 1987. Subsequently, this plan was modified again and approved as Y/TS-395, Revised RCRA Closure Plan for the Bear Creek Burial Grounds (February 29, 1988). Y/TS-395 was initially intended to apply to A Area, C-West, B Area, and the Walk-In Pits of BCBG. However, a concept was developed to include the B Area (non-RCRA regulated) in the Walk-In Pits so that both areas would be closed under one cap. This approach included a tremendous amount of site preparation with an underlying stabilization base of 16 ft of sand for blast protection. The plan was presented to the state of Tennessee on March 8, 1990, and the Department of Energy was requested to review other unique alternatives to close the site. This amended closure plan goes further to include inspection and maintenance criteria along with other details

Pitting growth rate in carbon steel exposed to simulated radioactive waste

International Nuclear Information System (INIS)

Zapp, P.E.

1996-06-01

Dilute high-level radioactive waste slurries can induce pitting corrosion in carbon steel tanks in which such waste is stored and processed. The waste is normally maintained with closely monitored nitrite and hydroxide concentrations known to prevent the initiation of pitting. Coupon immersion tests are being conducted in laboratory simulants of waste to determine the probability and growth rate of pitting in steel in the event of out-of-limits nitrite concentrations. Sets of about 36 carbon steel coupons have been immersed in known corrosive conditions (nitrite < 5 per cent of the established limit) at a temperature of 50 degrees C. Three sets have been removed from testing after 64, 150, and 350 days of immersion. The long immersion times introduced variability in the exposure conditions due to the evaporation and replenishment of solution. The deepest corrosive attack was measured on each coupon by optical microscopy. The deepest pits were ranked and analyzed as a type 1 extreme value distribution to extrapolate from the coupon population to the maximum expected pit depths in a waste tank structure. The data were compared to a power law for pit growth, although the deepest pits did not increase monotonically with time in the limited data set

How culture matters in educational borrowing? Chinese teachers’ dilemmas in a global era

Directory of Open Access Journals (Sweden)

Sheng-nan Liu

2015-12-01

Full Text Available Educational borrowing may cause numerous dilemmas that emerge from cross-cultural differences among teachers in the globalization. Through the case study on the flipped classroom introduced from the United States into Chinese middle schools, this article presents an examination of dilemmas that teachers encountered during educational borrowing in the global era. Based on the theoretical literature on cultural-historical activity theory, the study used interviews, field observations, and documents from six secondary schools in mainland China for one and a half years to understand comprehensively the dilemmas that teachers encountered when implementing the flipped classroom. The findings indicate that understandings of knowledge production, transmission, and the goal of education in mainland China differ from those in the west, which is the main reason for the teacher dilemmas. Because of the diversity in social culture, we suggest that teachers should be more culturally sensitive and improve compatibility in the process of educational borrowing.

New generation expandable sand screens

OpenAIRE

Syltøy, Christer

2014-01-01

Master's thesis in Petroleum engineering This thesis aims to give a general insight into sand control and various sorts of sand control measures and applications of sand control tools. Special focus will be given to expandable sand screens – a technology which came about in the late 1990’s through the use of flexible, expandable tubulars as base pipe in sand screens. More specifically Darcy’s Hydraulic Endurance Screens, a compliant sand screen system using hydraulic activation, and the fu...

Saltation of non-spherical sand particles.

Directory of Open Access Journals (Sweden)

Zhengshi Wang

Full Text Available Saltation is an important geological process and the primary source of atmospheric mineral dust aerosols. Unfortunately, no studies to date have been able to precisely reproduce the saltation process because of the simplified theoretical models used. For example, sand particles in most of the existing wind sand movement models are considered to be spherical, the effects of the sand shape on the structure of the wind sand flow are rarely studied, and the effect of mid-air collision is usually neglected. In fact, sand grains are rarely round in natural environments. In this paper, we first analyzed the drag coefficients, drag forces, and starting friction wind speeds of sand grains with different shapes in the saltation process, then established a sand saltation model that considers the coupling effect between wind and the sand grains, the effect of the mid-air collision of sand grains, and the effect of the sand grain shape. Based on this model, the saltation process and sand transport rate of non-spherical sand particles were simulated. The results show that the sand shape has a significant impact on the saltation process; for the same wind speed, the sand transport rates varied for different shapes of sand grains by as much as several-fold. Therefore, sand shape is one of the important factors affecting wind-sand movement.

Pitting Corrosion of Ni3(Si,Ti Intermetallic Compound at Various Chloride Concentrations

Directory of Open Access Journals (Sweden)

Gadang Priyotomo

2013-10-01

Full Text Available The pitting corrosion of Ni3(Si,Ti intermetallic compound was investigated as function of chloride concentration by using electrochemical method and scanning electron microscope in sodium chloride solutions at 293 K.  In addition, the pitting corrosion of type C276 alloy was also studied under the same experimental condition for comparison.  The pitting potential obtained for the intermetallic compound decreased with increasing chloride concentration.  The specific pitting potential and pitting potential of Ni3(Si,Ti were lower than those of C276 alloy, which means that the pitting corrosion resistance of C276 alloy was higher than that of Ni3(Si,Ti.

Simulation of Fatigue Crack Initiation at Corrosion Pits With EDM Notches

Science.gov (United States)

Smith, Stephen W.; Newman, John A.; Piascik, Robert S.

2003-01-01

Uniaxial fatigue tests were conducted to compare the fatigue life of laboratory produced corrosion pits, similar to those observed in the shuttle main landing gear wheel bolt-hole, and an electro-discharged-machined (EDM) flaw. EDM Jaws are used to simulate corrosion pits during shuttle wheel (dynamometer) testing. The aluminum alloy, (AA 7050) laboratory fatigue tests were conducted to simulate the local stress level contained in the wheel bolt-hole. Under this high local stress condition, the EDM notch produced a fatigue life similar to test specimens containing corrosion pits of similar size. Based on the laboratory fatigue test results, the EDM Jaw (semi-circular disc shaped) produces a local stress state similar to corrosion pits and can be used to simulate a corrosion pit during the shuttle wheel dynamometer tests.

Non Destructive Testing Measurement for Monitoring Pitting Corrosion using Dcp Techniques

International Nuclear Information System (INIS)

Atlam, A.; Omar, A.A.; Habashy, M.; Waheed, A.F.; Shafy, M.

2010-01-01

A repeatable monitoring of pit from in accessible side of a welded side of a structure is one of the hurdles in field of NT. The present work uses the DC potential drop measuring system for evaluating the response of pits in the weld joins to be detected by DC potential drop measurements. Weld joint of type 304L stainless steel welded with 308L was tested. Selected pits in different zones of the weld joint were detected by optical microscopy. The PD test shows difference in potential between pitted and non-pitted weld joints ranging from 1.3 in BM to 1.7 in HAZ. The capability of present monitoring process can be extended to evaluate the reduction in thickness for the case of thick stainless steel structure

Study of pitting corrosion in line-pipe steel under the influence of remanent magnetization

Energy Technology Data Exchange (ETDEWEB)

Espina-Hernandez, J H; Caleyo, F; Hallen, J M [Instituto Politecnico Nacional (IPN), Zacatenco (Mexico)

2009-07-01

The influence of remanent magnetization on pitting corrosion in line-pipe steels is studied. Pitting corrosion experiments have been carried out on samples of an API 5L grade 52 steel under a magnetization level of the same order of magnitude of the remanent magnetization in the pipeline wall after in-line inspection based on magnetic flux leakage. The samples were magnetized using rings of the same grade as the investigated steel. Immediately after magnetization, the investigated samples were subjected to pitting by immersing them in a solution containing dissolved Cl{sup -} and SO{sup 2-}{sub 4} and ions. The pitting experiments were conducted during a seven days period. The pit depth distribution and the maximum pit depth in each sample were recorded and used to conduct extreme value analyses of the pitting process in magnetized and non-magnetized control samples. The statistical assessment of the pitting corrosion data collected during this study shows that the magnetic field reduces the average depth of the pit population and also the extreme pit depth values that can be predicted from the maximum values observed in the magnetized samples in comparison with to the non-magnetized control samples. Scanning electron microscopy observations show that the magnetic field alters the pit morphology by increasing the pit mouth opening. (author)

Markov Chain Models for the Stochastic Modeling of Pitting Corrosion

OpenAIRE

Valor, A.; Caleyo, F.; Alfonso, L.; Velázquez, J. C.; Hallen, J. M.

2013-01-01

The stochastic nature of pitting corrosion of metallic structures has been widely recognized. It is assumed that this kind of deterioration retains no memory of the past, so only the current state of the damage influences its future development. This characteristic allows pitting corrosion to be categorized as a Markov process. In this paper, two different models of pitting corrosion, developed using Markov chains, are presented. Firstly, a continuous-time, nonhomogeneous linear growth (pure ...

Resistance to pitting corrosion in ferritic and austenitic/ferritic steels

International Nuclear Information System (INIS)

De Bouvier, O.

1995-01-01

Stainless steel tubes carrying raw water are potentially vulnerable to pitting corrosion. With a view to minimizing the corrosion risk in the river-water-cooled condensers at PWR power plant, a study was conducted to determine initiation conditions and incubation durations for pitting corrosion in stagnant water. As a result, condenser tubes in Z2 CI 18 (439) or Z2 CT 18-10 (304L) steels were phased out in favour of Z2 CND 16-32 (316L) stainless steel. The same question can be yield for other applications and especially for all types of exchangers for use in electrical applications. This study sought to assess alternative methods for estimating pitting corrosion, and to check the results of these methods against the actual behaviour of studied steels. The study covered ferritic steels (439, 444, 290Mo), austenitic steel (316L) and austenitic/ferritic steels (Uranus 35N, 45N, 47N, 52N). Two approaches were adopted: laboratory tests to compare pitting corrosion risks on different materials, and tests for characterizing the behaviour of steels exposed to river water. The study begins with a laboratory tests that yield an arbitrary parameter for quantifying pitting corrosion resistance. One method involves measuring the pitting temperature in an aggressive ferric chloride solution. Other methods measure the pitting potential, either statistically (Multipit method) or deterministically (polarization curve). We then go on to discuss tests under simulated life-like conditions, involving repeated immersions in water from the Seine. (author). 9 refs., 13 figs, 9 tabs

Adaptive dynamic capacity borrowing in road-covering mobile networks

NARCIS (Netherlands)

Ule, A.; Boucherie, Richardus J.; Li, W.; Pan, Y.

2006-01-01

This paper introduces adaptive dynamic capacity borrowing strategies for wireless networks covering a road. In a F/TDMA-based model, road traffic prediction models are used to characterise the movement of hot spots, such as traffic jams, and subsequently to predict the teletraffic load offered to

Mining-induced earthquakes monitored during pit closure in the Midlothian Coalfield

Energy Technology Data Exchange (ETDEWEB)

Redmayne, D.W.; Richards, J.A.; Wild, P.W. [British Geological Survey, Edinburgh (United Kingdom). Global Seismology and Geomagnetism Group

1998-06-01

The British Geological Survey installed a seismometer network to monitor earthquakes around Rosslyn Chapel in the Midlothian Coalfield from November 1987 until January 1990. Accurate locations were obtained for 247 events and a close spatial and temporal association with concurrent coal mining, with a rapid decay of earthquake activity following pit closure, was demonstrated, indicating a mining-induced cause. Residual stress from past mining appears to have been an important factor in generating seismicity, and observations indicate that limiting the width of the workings or rate of extraction may significantly reduce or eliminate mining-induced earthquake activity. A frequency-magnitude analysis indicates a relatively high abundance of small events in this coalfield area. The maximum magnitude of a mining-induced earthquake likely to have been experienced during the life of the coalfield (maximum credible magnitude) was 3.0 M-L, although an extreme event (maximum possible magnitude) as large as 3.4 M-L was remotely possible. Significant seismic amplification was observed at Rosslyn Chapel, which is founded on sand and gravel, compared with a nearby bedrock site. As a consequence, relatively small magnitude events caused high, and occasionally damaging, seismic intensities at the chapel.

5G in Open-Pit Mines

DEFF Research Database (Denmark)

Portela Lopes de Almeida, Erika; Caldwell, George; Rodriguez Larrad, Ignacio

2017-01-01

5G will play a pivotal role in the digitization of the industrial sector and is expected to make the best use of every bit of spectrum available. In this light, this paper presents the results of an extensive measurement campaign in two iron-ore open-pit mining complexes, at the 700 MHz and 2.6 GHz...... for the future wireless network design, simulation and performance evaluation. The results show that, in order to comply with ultra-reliable communications (URC) availability requirements, larger shadowing margins will have to be considered in the network planning in open-pit mines, when compared to traditional...

Lexical borrowing by Khoekhoegowab from Cape Dutch and Afrikaans

Directory of Open Access Journals (Sweden)

Wilfrid Haacke

2015-02-01

Full Text Available The present article instantiates types of lexical borrowing from Afrikaans and Dutch in Namibian Khoekhoegowab (also known as “Nama”/“Damara”, but occasionally also refers to borrowings in the opposite direction. Where evidence allows, loans are traced back beyond Afrikaans to the era of Cape Dutch and contemporary interethnic contacts. Various categories ranging from adoptions to phonologically integrated loans, hybrids and calques are presented and, where possible, historical inferences are offered. The high degree of translational equivalence between Khoekhoe serial verbs and Afrikaans compound verbs leads to the consideration of some grammatical aspects including replication and relexification. Finally, reference is made to a parallel between Afrikaans and “Khoekhoe Afrikaans” syntax pointed out by den Besten (2013: Afrikaans circumlocutions like ek / sy wat Anna is (Khoekhoe: Anna.ta / Anna.s are literal equivalents of the underlying phrasal structures of Khoekhoe surface nouns #stem.pgn# in first, second or third person, as accounted for by the “desentential hypothesis” (Haacke 2006.  

Influence of lubricant on the pitting capacity of gears. Comparison and discussion of main pitting test methods

Energy Technology Data Exchange (ETDEWEB)

Hoehn, Bernd-Robert; Oster, Peter; Tobie, Thomas; Hergesell, Maria [Forschungsstelle fuer Zahnraeder und Getriebebau, Technische Univ. Muenchen, Garching (Germany)

2009-07-01

The lubricant in a gearbox should provide a separating lubricating film between the meshing teeth. Furthermore its main task is the evacuation of the developing heat. Hence the lubricant is also an important influence parameter on the pitting life time of gearsets. Due to the constantly rising demands for higher power transmission of gearsets, also higher demands are made against the performance of the lubricants. In order to quantify the capability and to choose the appropriate lubricant for each application, reliable testing methods are necessary. Therefor today different testing methods are available. Two of the main pitting testing methods are the Standard Pittingtest according to FVA 2/IV [2] and its advancement, the Practice Relevant Pittingtest according to FVA 371 [4]. For the Practice Relevant Pittingtest test gears with profile modification and lengthwise crowning are used, which are superfinished. For the introduction of the Practice Relevant Pittingtest into industrial application a round robin test was performed in co-operation with FVA and DGMK. This paper is discussing the today usual testing methods regarding the pitting load capacity of lubricants and their characteristics in comparison. Furthermore the results of the round robin test and further example results, including pictures of typical pittings, are presented. In addition it is demonstrated, how to deal with the results. On the basis of test experience, knowledge from research projects and other examples typical questions concerning the different testing methods are discussed. Thereby essential requirements for reliable and reproducible results are pointed out and possible limits for the application of the test methods are represented. (orig.)

In situ vitrification demonstration at Pit 1, Oak Ridge National Laboratory. Volume 2: Site characterization report of the Pit 1 area

International Nuclear Information System (INIS)

Spalding, B.P.; Bogle, M.A.; Cline, S.R.; Naney, M.T.; Gu, B.

1997-12-01

A treatability study was initiated in October 1993, initially encompassing the application of in situ vitrification (ISV) to at least two segments of Oak Ridge National Laboratory (ORNL) seepage Pit 1 by the end of fiscal year (FY) 1995. This treatability study was to have supported a possible Interim Record of Decision (IROD) or removal action for closure of one or more of the seepage pits and trenches as early as FY 1997. The Remedial Investigation/Feasibility Study for Waste Area Grouping (WAG) 7, which contains these seven seepage pits and trenches, will probably not begin until after the year 2000. This treatability study will establish the field-scale technical performance of ISV for (1) attaining the required depth, nominally 15 ft, to incorporate source contamination within and beneath the pits; (2) demonstrating field capability to overlap melt settings that are necessary to achieve fused, melted segments of the source contamination; (3) demonstrating off-gas handling technology for accommodating and minimizing the volatilization of 137 Cs; (4) demonstrating adequate site characterization techniques to predict ISV melting kinetics, processing temperatures, and product durability; and (5) promoting public acceptance of ISV technology by demonstrating its safety, implementability, site impacts, and air emissions and by coordinating the treatability study within the regulatory closure process. This report summarizes the site characterization information gathered through the end of September 1996 which supports the planning and assessment of ISV for Pit 1 (objective 4 above)

In situ vitrification demonstration at Pit 1, Oak Ridge National Laboratory. Volume 2: Site characterization report of the Pit 1 area

Energy Technology Data Exchange (ETDEWEB)

Spalding, B.P.; Bogle, M.A.; Cline, S.R.; Naney, M.T.; Gu, B.

1997-12-01

A treatability study was initiated in October 1993, initially encompassing the application of in situ vitrification (ISV) to at least two segments of Oak Ridge National Laboratory (ORNL) seepage Pit 1 by the end of fiscal year (FY) 1995. This treatability study was to have supported a possible Interim Record of Decision (IROD) or removal action for closure of one or more of the seepage pits and trenches as early as FY 1997. The Remedial Investigation/Feasibility Study for Waste Area Grouping (WAG) 7, which contains these seven seepage pits and trenches, will probably not begin until after the year 2000. This treatability study will establish the field-scale technical performance of ISV for (1) attaining the required depth, nominally 15 ft, to incorporate source contamination within and beneath the pits; (2) demonstrating field capability to overlap melt settings that are necessary to achieve fused, melted segments of the source contamination; (3) demonstrating off-gas handling technology for accommodating and minimizing the volatilization of {sup 137}Cs; (4) demonstrating adequate site characterization techniques to predict ISV melting kinetics, processing temperatures, and product durability; and (5) promoting public acceptance of ISV technology by demonstrating its safety, implementability, site impacts, and air emissions and by coordinating the treatability study within the regulatory closure process. This report summarizes the site characterization information gathered through the end of September 1996 which supports the planning and assessment of ISV for Pit 1 (objective 4 above).

Slavic borrowings in modern Turkish language

Directory of Open Access Journals (Sweden)

Đinđić Marija

2006-01-01

Full Text Available This paper deals with Slavic borrowings in standard Turkish language Material for this paper was excerpted from the Dictionary of Turkish Standard Language (TDK Turküe Sozluk. Excerpted data which count just about 100 words were treated within lexical-semantic groups, also with pointing to certain inconsistencies in the lexicographic treatment: some words are not marked as Slavic (e.g. kumpir, som, pogrom; after some lexemes wrong etymon is stated (e.g. kopek and some of them are left without an etymon (e.g. bocuk, gocuk.

Pitting process visualization

Directory of Open Access Journals (Sweden)

Michal Černý

2010-01-01

Full Text Available The paper describes time-domain simulation of gear pitting damage using animation program. Key frames have been used to create illusion of motion. The animation uses experimental results of high-cycle fatigue of material. The fatigue damage occurs in the nominal creep area on the side of the gear tooth sample loaded with variable-positioned Hertz pressure. By applying the force, the pressure cumulates between two convex surfaces. This phenomenon results in material damage under of curved surfaces in contact. Moreover, further damage has been registered on the surface. This is due to exceeding the elastic-plastic state limit and development of „tabs“. The tabs serve as origin of surface micro cracks powered by shear stress and enclosed grease pressure as well. This deformation and extreme pressures of Pascal law contribute to elongation and growth of the surface micro crack. Non-homogenous parts of material volume support the initialization/development of the micro cracks as well. Resulting visualization of the tooth-side fatigue damage provides clear and easy-to-understand description of the damage development process right from the micro crack initialization to the final fragmentation due to pitting degradation.

Pitting by corrosion in aluminium and Al-6201 alloy

International Nuclear Information System (INIS)

Vera, R.; Schrebler, R.; Layana, G.; Orellana, F.; Olguin, A.

1998-01-01

The susceptibility of pure aluminum 6201 alloy to pitting was investigated in sodium chloride solutions through determination of the corrosion, repassivation and pitting potentials. Potentiodynamic polarization including scratching techniques were employed being also determined the type and relative amount of corrosion damage to the metals. The morphology of the attach was determined using scanning electrons microscopy (SEM). The results showed a similar performance for aluminum 6201 alloy and aluminum. It was also observed that an increase in chloride concentration resulted in a decrease in the corrosion, pitting and repassivation potentials of both materials. (Author) 19 refs

Pitting of Incoloy 800 in presence of CuII

International Nuclear Information System (INIS)

Bianchi, G.L.; Alvarez, M.G.

1993-01-01

The pitting behaviour of Incoloy 800 in presence of Cu II ions, at 60 degrees C and 280 degrees C was studied by long term exposition of specimens in aqueous cupric chloride solutions. At 60 degrees C experiments were performed in aerated (7 ppm O 2 ) and deaerated solutions containing 500, 1000, 2000, 10000 and 20000 ppm CuCl 2 . At 280 degrees C experiments were performed in deaerated 20 ppm, 50 ppm and 100 ppm CuCl 2 solutions. During each experiment the open circuit potential of the alloy was measured as a function of time. After corrosion test the specimens were examined by Scanning Electron Microscopy for the presence of pits. In another set of experiments potentiodynamic anodic polarization curves were used to determine the pitting potential of Incoloy 800 in deaerated NaCl solutions at chloride concentrations and pH values corresponding to those possessed by solutions containing 20 ppm to 20000 ppm CuCl 2 . At 60 degrees C pitting was observed in those solutions where the CuCl 2 concentration is higher than 1000 ppm. At 280 degrees C pitting was found in the specimens exposed to those solutions where the CuCl 2 concentration was higher than 20 ppm. (author). 3 refs

Annealing to Mitigate Pitting in Electropolished Niobium Coupons and SRF Cavities

Energy Technology Data Exchange (ETDEWEB)

Cooley, L.D.; Hahn, E.; Hicks, D.; Romanenko, A.; Schuessler, R.; Thompson, C.; /Fermilab

2011-06-08

Ongoing studies at Fermilab investigate whether dislocations and other factors instigate pitting during cavity electropolishing (EP), despite careful processing controls and the inherent leveling mechanism of EP itself. Here, cold-worked niobium coupons, which exhibited increased tendencies for pitting in our past study, were annealed in a high vacuum furnace and subsequently processed by EP. Laser confocal scanning microscopy and special defect counting algorithms were used to assess the population of pits formed. Hardness measurements indicated that annealing for 2 hours at 800 C produced recovery, whereas annealing for 12 hours at 600 C did not, as is consistent with known changes for cavities annealed in a similar way. The 800 C anneal was effective in some cases but not others, and we discuss reasons why tendencies for pitting remain. We discuss implications for cavities and continued work to understand pitting.

Congenital upper lip pit: A rare case report

Directory of Open Access Journals (Sweden)

Leena James

2015-01-01

Full Text Available One of the rarest developmental malformations of the lip is congenital lip pits. They are usually seen as bilateral depressions in the vermilion zone of the lip and occur on the paramedian portion of the vermilion border of the lip. They are extremely rare in the upper lip. Lip pits are due to the failure of complete union of embryonic lateral sulci of the lip/notching of lip at an early stage of development with fixation of tissues of the base of the notch. Lip pits have also been associated with a variety of other congenital disorders and other malformations. The clinical and pathologic picture and the therapeutic aspects of this condition are discussed in this paper.

Numerical Investigation on Stress Concentration of Tension Steel Bars with One or Two Corrosion Pits

Directory of Open Access Journals (Sweden)

Jian Hou

2015-01-01

Full Text Available Pitting corrosion has been observed in steel bars of existing reinforced concrete (RC structures in different erosion environments and has been identified as a potential origin for fatigue crack nucleation. In the present study, under uniaxial tension loading, stress distribution in the steel bars with one or two semiellipsoidal corrosion pits has systematically been investigated by conducting a series of three-dimensional semiellipsoidal pitted models. Based on the finite element analyses, it is shown that stress concentration factor (SCF increases linearly with increasing pit aspect ratio (a/b and increases nonlinearly with increasing pit relative depth (a/R for single corrosion pit problem. For double corrosion pits problem, the SCF decreases nonlinearly with increasing angle of two transverse pits (θ. The interaction of two longitudinal pits can be ignored in the calculation of SCF even if the distance of two pits (d is very small.

Liquefaction resistance of calcareous sands

International Nuclear Information System (INIS)

Sandoval Vallejo, Eimar

2012-01-01

Calcareous sands are unique in terms of their origin, mineralogy, shape, fragility and intra particle porosity. This article presents results from an experimental program carried out to study the liquefaction resistance of a calcareous sand retrieved from Cabo Rojo at Puerto Rico. The experimental program included mineralogical characterization, index properties, and undrained cyclic triaxial tests on isotropically consolidated reconstituted samples. Due to the large variation in the calcareous sand properties, results are compared with previous researches carried out on other calcareous sands around the world. Results showed a wide range in the liquefaction resistance of the studied calcareous sands. Cabo Rojo sand experienced greater liquefaction resistance than most of the calcareous sands used for comparison. Important differences in the excess pore pressure generation characteristics were also found.

Railroad Rails Containing Electrode-Induced Pitting from Pressure Electric Welding

Science.gov (United States)

2018-04-18

This paper describes the forensic evaluations of three railroad rails containing electrode-induced pitting. These evaluations include: magnetic particle inspection to nondestructively detect cracks emanating from the pitting; fractography to study th...

Exit Counseling Guide for Federal Student Loan Borrowers

Science.gov (United States)

Federal Student Aid, US Department of Education, 2010

2010-01-01

Student loans, unlike grants and work-study, are borrowed money that must be repaid, with interest, just like car loans and home mortgages. You cannot have these loans canceled because you didn't like the education you received, didn't get a job in your field of study or because you're having financial difficulty. Loans are legal obligations that…

Detailed investigation of current transients from metastable pitting events on stainless steel - the transition to stability

International Nuclear Information System (INIS)

Pistorius, P.C.; Burstein, G.T.

1992-01-01

Current transients which result from metastable pitting events (on Type 304 stainless steel in an acidic solution containing 1 M Cl - ) are presented. A criterion for the stable growth of open hemispherical pits is developed; the criterion states that the product of current density and pit depth must exceed a certain minimum value, to sustain rapid dissolution. Analysis of the transients from metastable pits shows that these pits fall short of this minimum, as do stable pits initially. The growth of these pits thus requires the presence of another barrier to diffusion, which is thought to be a remnant of the passive film; this forms a flawed cover over the pit mouth. When this cover ruptures under the influence of osmotic pressure, the pit repassivates. Pits growing at higher current densities approach the minimum requirement for stable growth more closely. A ''pitting potential'' results from the effect that metastable pits formed at more positive potentials grow at higher current densities, and are thus more likely to grow into stable pits. The effect of potential on the current density does not result from either activation control or ohmic control; rather, the pits grow under diffusion control. A change, with potential, of the type of pit site which can be activated, causes the potential dependence of the distribution of current densities in metastable pits. Although the distribution of current densities changes with potential, each metastable pit grows under diffusion control with a current density which is independent of the potential; this is confirmed by polarisation tests on growing metastable pits

New insights in the role of working memory in carry and borrow operations

Directory of Open Access Journals (Sweden)

Ineke Imbo

2005-06-01

Full Text Available The present paper provides a state-of-the-art overview concerning the role of working memory in carry and borrow operations in mental arithmetic. The role of the executive working-memory component is discussed, alongside the contribution of the phonological and visuo-spatial working-memory components. Moreover, a broad view on various carry characteristics (such as the number of carry/borrow operations and the value of the carry and various operations (addition, subtraction, and multiplication is provided. Finally, some ideas for further research are offered.

Pit 9 project: A private sector initiative

International Nuclear Information System (INIS)

Macdonald, D.W.; Hughes, F.P.; Burton, B.N.

1993-01-01

This report discusses the Pit 9 Comprehensive Demonstration which is intended to demonstrate a cost-effective approach to remediate an Idaho National Engineering Laboratory (INEL) waste disposal pit through a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) Interim Action. The remediation will include additional requirements, if needed, to provide high confidence that only minor additional work would be necessary to accomplish the final closure as part of the overall final closure strategy for the INEL's Subsurface Disposal Area (SDA)

Nucleation sites of Ge nanoislands grown on pit-patterned Si substrate prepared by electron-beam lithography

Science.gov (United States)

Smagina, Zh. V.; Zinovyev, V. A.; Rudin, S. A.; Novikov, P. L.; Rodyakina, E. E.; Dvurechenskii, A. V.

2018-04-01

Regular pit-patterned Si(001) substrates were prepared by electron-beam lithography followed by plasma chemical etching. The geometry of the pits was controlled by varying the etching conditions and the electron-beam exposure duration. It was shown that the location of three-dimensional (3D) Ge nanoislands subsequently grown on the pit-patterned Si substrates depends on the shape of the pit bottom. In the case of pits having a sharp bottom, 3D Ge islands nucleate inside the pits. For pits with a wide flat bottom, the 3D Ge island nucleation takes place at the pit periphery. This effect is attributed to the strain relaxation depending not only on the initial pit shape, but also on its evolution during the Ge wetting layer deposition. It was shown by Monte Carlo simulations that in the case of a pit with a pointed bottom, the relaxation is most effective inside the pit, while for a pit with a wide bottom, the most relaxed area migrates during Ge deposition from the pit bottom to its edges, where 3D Ge islands nucleate.

Pitting Corrosion Topography Characteristics and Evolution Laws of LC4 Aluminum Alloy in Service Environment

Directory of Open Access Journals (Sweden)

LIU Zhiguo

2017-08-01

Full Text Available Aircraft aluminum alloy is easy to initiate pitting corrosion in the service environment, the pitting corrosion topography characteristics could directly affect the fatigue mechanical property of structure material. In order to obtain the pitting corrosion topography characteristics of LC4 aluminum alloy in the service environment, the accelerated corrosion test was carried out along the accelerated corrosion test environment spectrum which imitated the service environment spectrum, and the corrosion topography characteristic parameters of corrosion pit depth H,corrosion pit surface length L and corrosion pit surface width W were defined respectively. During the corrosion test process,the three parameters of typical corrosion pit were successively measured in different equivalent corrosion years for obtaining the corrosion pit damage size data, then the data were analysed through the statistics method and fractal theory. Further more in order to gain the pit topography characteristics in the same equivalent corrosion year and the topography evolution laws during different equivalent corrosion years were gained. The analysis results indicate that LC4 aluminum alloy corrosion pit topography characteristics in the service environment include the following:firstly, the pit topography characteristic parameters conform to the lognormal distributions in the same equivalent corrosion years; secondly,the pit topography characteristic parameters gradually reflect the fractal feature in accordance with the equivalent corrosion year increment, and the pits tend to be shallow, long and moderate wide topography character.

Large heterogeneities in comet 67P as revealed by active pits from sinkhole collapse.

Science.gov (United States)

Vincent, Jean-Baptiste; Bodewits, Dennis; Besse, Sébastien; Sierks, Holger; Barbieri, Cesare; Lamy, Philippe; Rodrigo, Rafael; Koschny, Detlef; Rickman, Hans; Keller, Horst Uwe; Agarwal, Jessica; A'Hearn, Michael F; Auger, Anne-Thérèse; Barucci, M Antonella; Bertaux, Jean-Loup; Bertini, Ivano; Capanna, Claire; Cremonese, Gabriele; Da Deppo, Vania; Davidsson, Björn; Debei, Stefano; De Cecco, Mariolino; El-Maarry, Mohamed Ramy; Ferri, Francesca; Fornasier, Sonia; Fulle, Marco; Gaskell, Robert; Giacomini, Lorenza; Groussin, Olivier; Guilbert-Lepoutre, Aurélie; Gutierrez-Marques, P; Gutiérrez, Pedro J; Güttler, Carsten; Hoekzema, Nick; Höfner, Sebastian; Hviid, Stubbe F; Ip, Wing-Huen; Jorda, Laurent; Knollenberg, Jörg; Kovacs, Gabor; Kramm, Rainer; Kührt, Ekkehard; Küppers, Michael; La Forgia, Fiorangela; Lara, Luisa M; Lazzarin, Monica; Lee, Vicky; Leyrat, Cédric; Lin, Zhong-Yi; Lopez Moreno, Josè J; Lowry, Stephen; Magrin, Sara; Maquet, Lucie; Marchi, Simone; Marzari, Francesco; Massironi, Matteo; Michalik, Harald; Moissl, Richard; Mottola, Stefano; Naletto, Giampiero; Oklay, Nilda; Pajola, Maurizio; Preusker, Frank; Scholten, Frank; Thomas, Nicolas; Toth, Imre; Tubiana, Cecilia

2015-07-02

Pits have been observed on many cometary nuclei mapped by spacecraft. It has been argued that cometary pits are a signature of endogenic activity, rather than impact craters such as those on planetary and asteroid surfaces. Impact experiments and models cannot reproduce the shapes of most of the observed cometary pits, and the predicted collision rates imply that few of the pits are related to impacts. Alternative mechanisms like explosive activity have been suggested, but the driving process remains unknown. Here we report that pits on comet 67P/Churyumov-Gerasimenko are active, and probably created by a sinkhole process, possibly accompanied by outbursts. We argue that after formation, pits expand slowly in diameter, owing to sublimation-driven retreat of the walls. Therefore, pits characterize how eroded the surface is: a fresh cometary surface will have a ragged structure with many pits, while an evolved surface will look smoother. The size and spatial distribution of pits imply that large heterogeneities exist in the physical, structural or compositional properties of the first few hundred metres below the current nucleus surface.

Threshold Considerations and Wetland Reclamation in Alberta's Mineable Oil Sands

Directory of Open Access Journals (Sweden)

Lee Foote

2012-03-01

Full Text Available Oil sand extraction in Alberta, Canada is a multibillion dollar industry operating over 143 km² of open pit mining and 4600 km² of other bitumen strata in northern boreal forests. Oil production contributes to Canada-wide GDP, creates socio-cultural problems, provides energy exports and employment, and carries environmental risks regarding long-term reclamation uncertainties. Of particular concern are the implications for wetlands and water supply management. Mining of oil sands is very attractive because proven reserves of known quality occur in an accessible, politically stable environment with existing infrastructure and an estimated 5.5 billion extractable barrels to be mined over the next five decades. Extraction occurs under a set of limiting factors or thresholds including: limited social tolerance at local to international levels for externalities of oil sand production; water demands > availability; limited natural gas supplies for oil processing leading to proposals for hydroelectric dams and nuclear reactors to be constructed; difficulties in reclaiming sufficient habitat area to replace those lost. Replacement of the 85 km² of peat-forming wetlands forecast to be destroyed appears unlikely. Over 840 billion liters of toxic fluid byproducts are currently held in 170 km² of open reservoirs without any known process to purify this water in meaningful time frames even as some of it leaches into adjacent lands and rivers. Costs for wetland reclamation are high with estimates of $4 to $13 billion, or about 6% of the net profits generated from mining those sites. This raises a social equity question of how much reclamation is appropriate. Time frames for economic, political, and ecological actions are not well aligned. Local people on or near mine sites have had to change their area use for decades and have been affected by industrial development. Examining mining effects to estimate thresholds of biophysical realities, time scales

Copper Tube Pitting in Santa Fe Municipal Water Caused by Microbial Induced Corrosion.

Science.gov (United States)

Burleigh, Thomas D; Gierke, Casey G; Fredj, Narjes; Boston, Penelope J

2014-06-05

Many copper water lines for municipal drinking water in Santa Fe, New Mexico USA, have developed pinhole leaks. The pitting matches the description of Type I pitting of copper, which has historically been attributed to water chemistry and to contaminants on the copper tubing surface. However, more recent studies attribute copper pitting to microbial induced corrosion (MIC). In order to test for microbes, the copper tubing was fixed in hexamethyldisilazane (HMDS), then the tops of the corrosion mounds were broken open, and the interior of the corrosion pits were examined with scanning electron microscopy (SEM). The analysis found that microbes resembling actinobacteria were deep inside the pits and wedged between the crystallographic planes of the corroded copper grains. The presence of actinobacteria confirms the possibility that the cause of this pitting corrosion was MIC. This observation provides better understanding and new methods for preventing the pitting of copper tubing in municipal water.

Copper Tube Pitting in Santa Fe Municipal Water Caused by Microbial Induced Corrosion

Directory of Open Access Journals (Sweden)

Thomas D. Burleigh

2014-06-01

Full Text Available Many copper water lines for municipal drinking water in Santa Fe, New Mexico USA, have developed pinhole leaks. The pitting matches the description of Type I pitting of copper, which has historically been attributed to water chemistry and to contaminants on the copper tubing surface. However, more recent studies attribute copper pitting to microbial induced corrosion (MIC. In order to test for microbes, the copper tubing was fixed in hexamethyldisilazane (HMDS, then the tops of the corrosion mounds were broken open, and the interior of the corrosion pits were examined with scanning electron microscopy (SEM. The analysis found that microbes resembling actinobacteria were deep inside the pits and wedged between the crystallographic planes of the corroded copper grains. The presence of actinobacteria confirms the possibility that the cause of this pitting corrosion was MIC. This observation provides better understanding and new methods for preventing the pitting of copper tubing in municipal water.

Markov chain model helps predict pitting corrosion depth and rate in underground pipelines

Energy Technology Data Exchange (ETDEWEB)

Caleyo, F.; Velazquez, J.C.; Hallen, J. M. [ESIQIE, Instituto Politecnico Nacional, Mexico D. F. (Mexico); Esquivel-Amezcua, A. [PEMEX PEP Region Sur, Villahermosa, Tabasco (Mexico); Valor, A. [Universidad de la Habana, Vedado, La Habana (Cuba)

2010-07-01

Recent reports place pipeline corrosion costs in North America at seven billion dollars per year. Pitting corrosion causes the higher percentage of failures among other corrosion mechanisms. This has motivated multiple modelling studies to be focused on corrosion pitting of underground pipelines. In this study, a continuous-time, non-homogenous pure birth Markov chain serves to model external pitting corrosion in buried pipelines. The analytical solution of Kolmogorov's forward equations for this type of Markov process gives the transition probability function in a discrete space of pit depths. The transition probability function can be completely identified by making a correlation between the stochastic pit depth mean and the deterministic mean obtained experimentally. The model proposed in this study can be applied to pitting corrosion data from repeated in-line pipeline inspections. Case studies presented in this work show how pipeline inspection and maintenance planning can be improved by using the proposed Markovian model for pitting corrosion.

Norm Levels in Mine Pit Lakes in South-Western Spain

International Nuclear Information System (INIS)

Manjón, G.; Galván, J.; Mantero, J.; Díaz, I.; García-Tenorio, R.

2015-01-01

Former mining activities in a pyritic area in south-western Spain have generated mine pits in which underground water and rainwater has accumulated. The accumulated waters have produced oxidation of the pyrite and, consequently, the pit water has become acidic, causing the dissolution of metals and radionuclides of natural origin. The paper discusses the activity concentration levels of uranium isotopes and other radionuclides in water samples and sediments collected from these mine pit lakes. Tributaries of the nearby Odiel River, when crossing the mining area, show low pH values and high concentrations of uranium isotopes due to acid mine drainage. Through the analysis of several isotope activity ratios, the presence of radionuclides in the pit lakes and the influence of these radionuclides on the surrounding area and the Odiel River are evaluated. (author)

Borrowing and Loan Words: The Lemmatizing of Newly Acquired ...

African Journals Online (AJOL)

rbr

or foreign acquisition. English, for instance, is spoken in many countries on all five continents and is, therefore, able to acquire vocabulary from many lan- guages worldwide. This is coupled with the readiness and the ability of the language to acquire new terminology through borrowing, instead of following the puristic ...

Transaction Cost Of Borrowing Among Small Scale Farmers In ...

African Journals Online (AJOL)

The study examined transaction cost of borrowing among small scale farmers in Rivers State, Nigeria. Data was collected with the aid of structured questionnaire from 109 randomly selected small scale farmers in the study area. Data analysis was by frequency, percentage and mean. It was found that farmers mostly ...

Analysis of borrowing and repayment of credit among livestock ...

African Journals Online (AJOL)

This study examined borrowing and repayment of credit among livestock farmers in Cross River State, Nigeria. Data for the study was obtained from the Bank of Agriculture (BOA), Calabar. Descriptive statistics such as percentage count, mean and tables were employed in the analysis. It was discovered that BOA in ...

Feedback Limiting the Coastal Response to Irregularities in Shelf Bathymetry

Science.gov (United States)

List, J. H.; Benedet, L.

2007-12-01

Observations and engineering studies have shown that non-uniform inner shelf bathymetry can influence longshore sediment transport gradients and create patterns of shoreline change. One classic example is from Grand Isle, Louisiana, where two offshore borrow pits caused two zones of shoreline accretion landward of the pits. In addition to anthropogenic cases, many natural situations exist in which irregularities in coastal planform are thought to result from offshore shoals or depressions. Recent studies using the hydrodynamic model Delft3D have successfully simulated the observed nearshore erosion and accretion patterns landward of an inner shelf borrow pit. An analysis of the momentum balance in a steady-state simulation has demonstrated that both alongshore pressure gradients (due to alongshore variations in wave setup) and radiation stress gradients (terms relevant to alongshore forcing) are important for forcing the initial pattern of nearshore sedimentation in response to the borrow pit. The response of the coast to non-uniform inner shelf bathymetry appears to be limited, however, because observed shoreline undulations are often rather subtle. (An exception may exist in the case of a very high angle wave climate.) Therefore, feedbacks in processes must exist such that growth of the shoreline salient itself modifies the transport processes in a way that limits further growth (assuming the perturbation in inner shelf bathymetry itself remains unchanged). Examination of the Delft3D momentum balance for an inner shelf pit test case demonstrates that after a certain degree of morphologic development the forcing associated with the well-known shoreline smoothing process (a.k.a., diffusion) counteracts the forcing associated with the inner shelf pit, producing a negative feedback which arrests further growth of the shoreline salient. These results provide insights into the physical processes that control shoreline changes behind inner shelf bathymetric anomalies (i

Numerical simulation of the double pits stress concentration in a curved casing inner surface

Directory of Open Access Journals (Sweden)

Wei Yan

2016-12-01

Full Text Available Sour or sweet oil fields development is common in recent years. Casing and tubing are usually subjected to pitting corrosion because of exposure to the strong corrosion species, such as CO2, H2S, and saline water. When the corrosion pits formed in the casing inner surface, localized stress concentration will occur and the casing strength will be degraded. Thus, it is essential to evaluate the degree of stress concentration factor accurately. This article performed a numerical simulation on double pits stress concentration factor in a curved inner surface using the finite element software ABAQUS. The results show that the stress concentration factor of double pits mainly depends on the ratio of two pits distance to the pit radius (L/R. It should not be only assessed by the absolute distance between the two pits. When the two pits are close and tangent, the maximum stress concentration factor will appear on the inner tangential edges. Stress concentration increased by double pits in a curved casing inner surface is more serious than that in a flat surface. A correction factor of 1.9 was recommended in the curved inner surface double pits stress concentration factor predict model.

MECHANICAL REGENERATION OF SAND WASTE

Directory of Open Access Journals (Sweden)

D. I. Gnir

2005-01-01

Full Text Available The experimental activation of the sand regenerator of the firm SINTO is carried out at ОАО “MZOO". It is shown that sand grains are cleared from films of binding agents, that allows to use the treated sand for preparation of agglutinant and core sands.

TRANSITIONS IN ELECTROCHEMICAL NOISE DURING PITTING CORROSION OF ALUMINUM IN CHLORIDE ENVIRONMENTS

International Nuclear Information System (INIS)

SASAKI, K.; ISAACS, H.S.; LEVY, P.W.

2001-01-01

Aluminum, in a chloride containing solutions close to its pitting potential, shows vigorous fluctuations in current and potential. Measurements have been made of the freely corroding potential, and the currents between interconnected electrodes. It is shown that there is a transition in the behavior of the transients. The transition occurs when multiple active pits are present and electrochemical communication occurs between them. The major source of current and potential transients is the growth process in the active pits rather than meta-stable pitting at the passive surface

TRANSITIONS IN ELECTROCHEMICAL NOISE DURING PITTING CORROSION OF ALUMINUM IN CHLORIDE ENVIRONMENTS.

Energy Technology Data Exchange (ETDEWEB)

SASAKI,K.; ISAACS,H.S.; LEVY,P.W.

2001-09-02

Aluminum, in a chloride containing solutions close to its pitting potential, shows vigorous fluctuations in current and potential. Measurements have been made of the freely corroding potential, and the currents between interconnected electrodes. It is shown that there is a transition in the behavior of the transients. The transition occurs when multiple active pits are present and electrochemical communication occurs between them. The major source of current and potential transients is the growth process in the active pits rather than meta-stable pitting at the passive surface.

12 CFR 617.7410 - When and how does a qualified lender notify a borrower of the right to seek loan restructuring?

Science.gov (United States)

2010-01-01

... borrower of the right to seek loan restructuring? 617.7410 Section 617.7410 Banks and Banking FARM CREDIT... Mediation Programs § 617.7410 When and how does a qualified lender notify a borrower of the right to seek... been identified as distressed and that the borrower has the right to request a restructuring of the...

Application of Surpac and Whittle Software in Open Pit Optimisation ...

African Journals Online (AJOL)

Application of Surpac and Whittle Software in Open Pit Optimisation and Design. ... This paper studies the Surpac and Whittle software and their application in designing an optimised pit. ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

Pitting corrosion of zirconium in aqueous solution

International Nuclear Information System (INIS)

El Shayeb, H.A.; Abd El Wahab, F.M.; Abd Elk Meguid, E.A.

1994-01-01

The open circuit potentials of the Zr electrode are followed as a function of time in various aqueous solutions till attainment of steady state values.The results are discussed on the basis of oxide film thickening and repair. Pitting corrosion of Zr was examined in chloride solutions using the potentiodynamic technique. The effect of some inorganic and organic additives was also investigated for inhibiting the pitting corrosion of Zr and the relative performance is presented and discussed. (author). 21 refs., 6 figs., 1 tab

PIT Coating Requirements Analysis

International Nuclear Information System (INIS)

MINTEER, D.J.

2000-01-01

This study identifies the applicable requirements for procurement and installation of a coating intended for tank farm valve and pump pit interior surfaces. These requirements are intended to be incorporated into project specification documents and design media. This study also evaluates previously recommended coatings and identifies requirement-compliant coating products

PIT Coating Requirements Analysis

Energy Technology Data Exchange (ETDEWEB)

MINTEER, D.J.

2000-10-20

This study identifies the applicable requirements for procurement and installation of a coating intended for tank farm valve and pump pit interior surfaces. These requirements are intended to be incorporated into project specification documents and design media. This study also evaluates previously recommended coatings and identifies requirement-compliant coating products.

The semantics of English Borrowings in Arabic Media Language: The case of Arab Gulf States Newspapers

Directory of Open Access Journals (Sweden)

Anwar A. H. Al-Athwary

2016-07-01

Full Text Available The present paper investigates the semantics of English loanwords in Arabic media language (AML. The loanword data are collected from a number of Arab Gulf states newspapers (AGSNs. They  are analyzed semantically from the points of view of semantic change, semantic domains, and the phenomenon of synonymy resulting from lexical borrowing. The semantic analysis has revealed that AML borrowings from English occur in fifteen distinctive semantic domains. Domains that are related to terms of technical and scientific nature are found ranking much higher (9% - 18% than those domains containing nontechnical elements (1% - 8% with the computer and technology category (18% is the most dominant domain. Almost all common mechanisms of semantic change (extension, restriction, amelioration, pejoration, and metaphorical extension are found at work in the context of AML borrowings. The tendency of semantic change in the overwhelming majority of AML borrowings is towards restriction.  Factors like need, semantic similarity, and factors of social and psychological considerations (e.g. prestige, taboo seem to be the potent factors at interplay in semantic change. The first two, i.e. need and semantic similarity, are the most common reasons in most types of semantic change. The problem of synonymy lies in those loanwords that have “Arabic equivalents” in the language. The study claims that this phenomenon could be attributed to the two simultaneous processes of lexical borrowing and?ištiqa:q (the modern efforts of deriving equivalent neologisms.

Effects-Directed Analysis of Dissolved Organic Compounds in Oil Sands Process-Affected Water.

Science.gov (United States)

Morandi, Garrett D; Wiseman, Steve B; Pereira, Alberto; Mankidy, Rishikesh; Gault, Ian G M; Martin, Jonathan W; Giesy, John P

2015-10-20

Acute toxicity of oil sands process-affected water (OSPW) is caused by its complex mixture of bitumen-derived organics, but the specific chemical classes that are most toxic have not been demonstrated. Here, effects-directed analysis was used to determine the most acutely toxic chemical classes in OSPW collected from the world's first oil sands end-pit lake. Three sequential rounds of fractionation, chemical analysis (ultrahigh resolution mass spectrometry), and acute toxicity testing (96 h fathead minnow embryo lethality and 15 min Microtox bioassay) were conducted. Following primary fractionation, toxicity was primarily attributable to the neutral extractable fraction (F1-NE), containing 27% of original organics mass. In secondary fractionation, F1-NE was subfractionated by alkaline water washing, and toxicity was primarily isolated to the ionizable fraction (F2-NE2), containing 18.5% of the original organic mass. In the final round, chromatographic subfractionation of F2-NE2 resulted in two toxic fractions, with the most potent (F3-NE2a, 11% of original organic mass) containing predominantly naphthenic acids (O2(-)). The less-toxic fraction (F3-NE2b, 8% of original organic mass) contained predominantly nonacid species (O(+), O2(+), SO(+), NO(+)). Evidence supports naphthenic acids as among the most acutely toxic chemical classes in OSPW, but nonacidic species also contribute to acute toxicity of OSPW.

Pitting morphologies of zirconium base alloys in aqueous and non aqueous chloride media

International Nuclear Information System (INIS)

Palit, G.C.; Gadiyar, H.S.

1988-01-01

Pitting morphology of zirconium and Zr-Cr alloys in aqueous chloride and nonaqueous methanol + 0.4 per cent HCl solution was investigated and observed to follow different modes in these two environments. While in aqueous chloride solution pitting was transgranular and randomly oriented, in methanol-chloride solution pits were observed to initiate and propagate along the grain boundaries. In aqueous chloride solution very irregular and sponge like zirconium metal was formed inside the pit while in methanol-chloride solution the pits were crystallographic in nature. Optical microscopy has revealed that pits preferentially initiate and propagate along scratch line in aqueous chloride solution, but such was not the case in nonaqueous methanol-chloride solution. The nature and the mechanism operating in the catastropic failure of these materials are investigated. (author). 10 refs., 11 figs

Pitting Corrosion Behaviour of New Corrosion-Resistant Reinforcement Bars in Chloride-Containing Concrete Pore Solution.

Science.gov (United States)

Jiang, Jin-Yang; Liu, Yao; Chu, Hong-Yan; Wang, Danqian; Ma, Han; Sun, Wei

2017-08-04

In this study, the pitting behaviour of a new corrosion-resistant alloy steel (CR) is compared to that of low-carbon steel (LC) in a simulated concrete pore solution with a chloride concentration of 5 mol/L. The electrochemical behaviour of the bars was characterised using linear polarisation resistance (LPR) and electrochemical impedance spectroscopy (EIS). The pitting profiles were detected by reflective digital holographic microscopy (DHM), scanning electron microscopy (SEM), and the chemical components produced in the pitting process were analysed by X-ray energy dispersive spectroscopy (EDS). The results show that the CR bars have a higher resistance to pitting corrosion than the LC bars. This is primarily because of the periodic occurrence of metastable pitting during pitting development. Compared to the pitting process in the LC bars, the pitting depth grows slowly in the CR bars, which greatly reduces the risk of pitting. The possible reason for this result is that the capability of the CR bars to heal the passivation film helps to restore the metastable pits to the passivation state.

A New Algorithm for Determining Ultimate Pit Limits Based on Network Optimization

Directory of Open Access Journals (Sweden)

Ali Asghar Khodayari

2013-12-01

Full Text Available One of the main concerns of the mining industry is to determine ultimate pit limits. Final pit is a collection of blocks, which can be removed with maximum profit while following restrictions on the slope of the mine’s walls. The size, location and final shape of an open-pit are very important in designing the location of waste dumps, stockpiles, processing plants, access roads and other surface facilities as well as in developing a production program. There are numerous methods for designing ultimate pit limits. Some of these methods, such as floating cone algorithm, are heuristic and do not guarantee to generate optimum pit limits. Other methods, like Lerchs–Grossmann algorithm, are rigorous and always generate the true optimum pit limits. In this paper, a new rigorous algorithm is introduced. The main logic in this method is that only positive blocks, which can pay costs of their overlying non-positive blocks, are able to appear in the final pit. Those costs may be paid either by positive block itself or jointly with other positive blocks, which have the same overlying negative blocks. This logic is formulated using a network model as a Linear Programming (LP problem. This algorithm can be applied to two- and three-dimension block models. Since there are many commercial programs available for solving LP problems, pit limits in large block models can be determined easily by using this method.

The Borrowers: Researching the cognitive aspects of translation

OpenAIRE

O'Brien, Sharon

2013-01-01

The paper considers the interdisciplinary interaction of research on the cognitive aspects of translation. Examples of influence from linguistics, psychology, neuroscience, cognitive science, reading and writing research and language technology are given, with examples from specific sub-disciplines within each one. The breadth of borrowing by researchers in cognitive translatology is made apparent, but the minimal influence of cognitive translatology on the respective disciplines themselves i...

Crushed rock sand – An economical and ecological alternative to natural sand to optimize concrete mix

Directory of Open Access Journals (Sweden)

Sanjay Mundra

2016-09-01

Full Text Available The study investigates the use of crushed rock sand as viable alternative to Natural River sand that is being conventionally used as fine aggregate in cement concrete. Various mix designs were developed for different grades of concrete based on IS, ACI and British codes using Natural River sand and crushed rock sand. In each case, the cube compressive strength test, and beam flexure tests were conducted. The results of the study show that, the strength properties of concrete using crushed rock sand are nearly similar to the conventional concrete. The study has shown that crushed stone sand can be used as economic and readily available alternative to river sand and can therefore help to arrest the detrimental effects on the environment caused due to excessive mining of river sand.

Analysis of two Pit-1 gene polymorphisms: Single nucleotide ...

African Journals Online (AJOL)

Pit-1 is a pituitary-specific transcription factor responsible for pituitary development and hormone expression in mammals. Pit-1 is a member of the POU domain containing proteins, a group of transcriptional regulators with a critical role in cell differentiation and proliferation. It was shown that this group of proteins control the ...

INFLUENCE OF PIT WALL ANCHORAGE ONTO ADDITIONAL DEFORMATIONS OF EXISTING BUILDINGS

Directory of Open Access Journals (Sweden)

Kubetskiy Valeriy Leonidovich

2012-07-01

Assessment of additional projected deformations of buildings located in close proximity to pits is exemplified by the specific structure of the pit support system that has active PIT [1] anchors. The authors also consider the influence produced by the structure of anchors onto the two buildings located within the area of influence of the excavation works and protected by the anchors installed underneath the foundations of the two adjacent buildings.

Critical pitting temperature for Type 254 SMO stainless steel in chloride solutions

International Nuclear Information System (INIS)

Abd El Meguid, E.A.; Abd El Latif, A.A.

2007-01-01

The variation with time of the open circuit potential of high molybdenum containing stainless steel (Type 254 SMO) was measured in 4% sodium chloride solution in the temperatures range 30-100 deg. C. The plot of steady state potentials as function of temperature showed an inflection at 50 deg. C, attributed to the decrease of oxygen solubility in test solution above 50 deg. C. Potentiodynamic cycling anodic polarization technique was used to determine the critical pitting potential (E pit ) and the critical protection potential (E prot ) of the steel in 4-30% NaCl solutions at temperatures between 30 and 100 deg. C. By plotting the two values versus solution temperature, the corresponding critical pitting (CPT) and the critical protection (CPrT) temperatures were determined. Both parameters decreased with increasing chloride content. Above the CPT, E pit and E prot decreased linearly with log[Cl - ]. The addition of bromide ions to the solution shifted both E pit and E prot towards positive values. In 4% NaCl, E pit increased linearly with pH in the range 1-10. The combined effect of chloride ion concentration and pH on the morphology of the pits was examined by scanning electron microscopy (SEM) following potentiodynamic cycling anodic polarization

Preliminary assessments of the occurrence and effects of utilization of sand and aggregate resources of the Louisiana inner shelf

Science.gov (United States)

Suter, J.R.; Mossa, J.; Penland, S.

1989-01-01

island restoration or beach nourishment raises the question of potential adverse effects on the shoreline due to alteration of the inner shelf bathymetry by removing material or deposition of spoil in the process of dredging. Wave refraction analysis models provide a means by which hypothetical wave energy distribution can be determined and possible changes due to resource utilization assessed. A preliminary assessment of the consequences of using sand from Ship Shoal, a large shore-parallel feature, as borrow material for beach nourishment was conducted. Initial results indicate that the shoal serves to attenuate storm waves, and removal of this feature would result in increased erosion and overwash on the adjacent Isles Dernieres barrier-island shoreline. These findings illustrate the need to determine optimum dredging configurations if environmentally deleterious effects of utilization of offshore and aggregate resources are to be minimized. ?? 1989.

Inspecting a research reactor's control rod surface for pitting using a machine vision

International Nuclear Information System (INIS)

Tokuhiro, Akira T.; Vadakattu, Shreekanth

2005-01-01

Inspection for pits on the control rod is performed to study the degradation of the control rod material which helps estimating the service life of the control rod at UMR nuclear reactor (UMRR). This inspection task is visually inspected and recorded subjectively. The conventional visual inspection to identify pits on the control rod surface can be automated using machine vision technique. Since the in-service control rods were not available to capture images and measure number of pits and size of the pits, the applicability of machine vision method was applied on SAE 1018 steel coupons immersed in oxygen saturated de-ionized water at 30deg, 50deg and 70deg. Images were captured after each test cycle at different light intensity to reveal surface topography of the coupon surface and analyzed for number of pits and pit size using EPIX XCAP-Std software. The captured and analyzed images provided quantitative results for the steel coupons and demonstrated that the method can be applied for identifying pits on control rod surface in place of conventional visual inspection. (author)

Initiation and inhibition of pitting corrosion on reinforcing steel under natural corrosion conditions

Energy Technology Data Exchange (ETDEWEB)

Abd El Wanees, S., E-mail: s_wanees@yahoo.com [Chemistry Department, Faculty of Science, University of Tabuk, Tabuk (Saudi Arabia); Chemistry Department, Faculty of Science, Zagazig University, Zagazig 44519 (Egypt); Bahgat Radwan, A. [Center for Advanced Materials, Qatar University, Doha 2713 (Qatar); Alsharif, M.A. [Chemistry Department, Faculty of Science, University of Tabuk, Tabuk (Saudi Arabia); Abd El Haleem, S.M. [Chemistry Department, Faculty of Science, Zagazig University, Zagazig 44519 (Egypt)

2017-04-01

Initiation and inhibition of pitting corrosion on reinforcing steel in saturated, naturally aerated Ca(OH){sub 2} solutions, under natural corrosion conditions, are followed through measurements of corrosion current, electrochemical impedance spectroscopy and SEM investigation. Induction period for pit initiation and limiting corrosion current for pit propagation are found to depend on aggressive salt anion and cation-types, as well as, concentration. Ammonium chlorides and sulfates are more corrosive than the corresponding sodium salts. Benzotriazole and two of its derivatives are found to be good inhibitors for pitting corrosion of reinforcing steel. Adsorption of these compounds follows a Langmuir adsorption isotherm. The thermodynamic functions ΔE{sup ∗}, ΔH{sup ∗} and ΔS{sup ∗} for pitting corrosion processes in the absence and presence of inhibitor are calculated and discussed. - Highlights: • Cl{sup −} and SO{sub 4} {sup 2-} induce pitting corrosion on passive reinforcing steel. • Initiation and propagation of pitting depend on cation and anion types. • Inhibition is based on adsorption according to Langmuir isotherm.

Pit membranes of Ephedra resemble gymnosperms more than angiosperms

Science.gov (United States)

Roland Dute; Lauren Bowen; Sarah Schier; Alexa Vevon; Troy Best; Maria Auad; Thomas Elder; Pauline Bouche; Steven Jansen

2014-01-01

Bordered pit pairs of Ephedra species were characterized using different types of microscopy. Pit membranes contained tori that did not stain for lignin. SEM and AFM views of the torus surface showed no plasmodesmatal openings, but branched, secondary plasmodesmata were occasionally noted using TEM in conjunction with ultrathin sections. The margo consisted of radial...

Rheological Characterization of Green Sand Flow

DEFF Research Database (Denmark)

Jabbaribehnam, Mirmasoud; Spangenberg, Jon; Hovad, Emil

2016-01-01

The main aim of this paper is to characterize experimentally the flow behaviour of the green sand that is used for casting of sand moulds. After the sand casting process is performed, the sand moulds are used for metal castings. The rheological properties of the green sand is important to quantif...

Formation of primary pit connection during conchocelis phase of Porphyra yezoensis (Bangiophyceae, Rhodophyta)

Science.gov (United States)

Shual, Li; Jiang, Ming; Duan, Delin

2006-09-01

The formation of pit connection during conchocelis phase of Porphyra yezoensis Ueda was observed and examined with transmission electron microscope (TEM) and epifluorence microscope. It is indicated that the pit connection was formed in late stage of conchocelis phase and the early stages of conchosporangial cell development, and disappeared in bispore stage. The pit connection contained a thin membrane layer at outer pit plug. Stained with 4', 6'-diamidino-2-phenylidole dihydrochloride hydrate (DAPI), transferring of DNA or RNA between adjacent cells were observed in late stage of conchocelis development, it was deduced that pit connection might serve as a channel for signal transduction and genetic substance transportation in conchocelis phase.

New diagnostic technology and hidden pits and fissures caries

Directory of Open Access Journals (Sweden)

Fabrizio Guerra

2015-10-01

Full Text Available The accuracy in pits and fissures caries detection is of paramount importance in dental caries primary and secondary prevention. A combination of visual examination and probing is currently the mainstay of occlusal caries diagnosis. Unfortunately, these types of inspection alone may leave a certain number of pit and fissure caries undetected. The Vista Cam iX fluorescence camera (Durr Dental, Bietigheim-Bissingen, Germany is a novel dental diagnostic tool for quantitative assessment of dental caries with high specificity for carious lesions detection. In the presented cases photographic images, representing the visual diagnostic approach, are applied as integration to VistaCam iX Proof images. A step-by-step sequence of inspection and assessment of operative treatment need is presented in a case of hidden pit and fissure caries on a permanent molar. Based on the reported case, it could be observed that VistaCam iX Proof shows promising results in hidden pits and fissures caries detection and could be considered a non-invasive examination method that facilitate the detection of early lesions and a potential diagnostic aid.

200 West Ash Pit Demolition Site closure plan

International Nuclear Information System (INIS)

1992-11-01

The Hanford Facility is owned by the US Government and operated by the US Department of Energy, Richland Field Office. Dangerous waste and mixed waste (containing both radioactive and dangerous components) are managed and produced on the Hanford Facility. Westinghouse Hanford Company is a major contractor to the US Department of Energy, Richland Field Office and serves as cooperator of the 200 West Ash Pit Demolition Site, the unit addressed in this closure plan. The 200 West Ash Pit Demolition Site Closure Plan consists of a Part A Permit Application (Revision 3) and a closure plan. An explanation of the Part A Permit Application revision is provided at the beginning of the Part A section. The closure plan consists of nine chapters and three appendices. This 200 West Ash Pit Demolition Site Closure Plan submittal contains information current as of October 15, 1992

PENGARUH MODIFIED AUDIT OPINION TERHADAP BORROWING CASH FLOW DAN INVESTMENT CASH FLOW

Directory of Open Access Journals (Sweden)

Puspita Hardina Cahyaningrum

2013-06-01

Full Text Available This study examines and analyzes the economic consequences of modified audit opinion on borrowing cash flow and investment cash flow. Panel data model was used to observe the research. The sample of this study was 247 companies listed in Indonesia Stock Exchange for the years 2008-2010. The results show that modified audit opinion, except unqualified opinion with explanatory paragraph about going concern, did not affect borrowing cash flow because audit opinion was not the only consideration for granting credit by creditors. Companies receiving modified audit opinion were proven using more operating cash flow for investing shown in investment cash flow, especially companies receiving unqualified opinion with explanatory paragraph about going concern.

Preliminary quantification of a shape model for etch-pits formed during natural weathering of olivine

International Nuclear Information System (INIS)

Nowicki, M. Anna; Velbel, Michael A.

2011-01-01

Many etch-pits on olivine grains occur as a pair of cone-shaped pits sharing a base, which consequently appear as diamond-shaped etch-pits in cross-section. Quantitative image analysis of back-scattered electron images establishes empirical dimensions of olivine etch-pits in naturally weathered samples from Hawaii and North Carolina. Images of naturally etched olivine were acquired from polished thin-sections by scanning electron microscopy. An average cone-radius-to-height ratio (r:h) of 1.78 was determined for diamond-shaped cross-sections of etch-pits occurring in naturally weathered olivine grains, largely consistent with previous qualitative results. Olivine etch-pit shape as represented by r:h varies from slightly more than half the average value to slightly more than twice the average. Etch-pit shape does not appear to vary systematically with etch-pit size.

Ecological geology environmental assessment of open-pit mines

International Nuclear Information System (INIS)

Dong Shuangfa; Jiang Xue

2010-01-01

In this paper, there is a detail description of ecological geology environmental assessment of open-pit mines, including method, process and results. We took ecological geology environmental assessment work on the base of the results of some open-pit mines such as extremely low content magnetite in Hebei Province, inducted and summarized the ecological geology environment quality. The results are reasonable. It provides basic data for the second mines programming in Hebei Province. (authors)

Análise multivariada de atributos nutricionais associados ao "bitter pit" em maçãs 'Gala' Multivariate analysis of nutritional attributes associated with bitter pit in 'Gala' apples

Directory of Open Access Journals (Sweden)

Cassandro Vidal Talamini do Amarante

2006-05-01

Full Text Available O objetivo deste trabalho foi identificar atributos nutricionais, quantificados na polpa e na casca dos frutos, que melhor discriminam quanto à severidade de "bitter pit" em maçãs 'Gala'. Depois de quatro meses de armazenamento em atmosfera normal (0-1°C; 90-95% UR, os frutos foram separados em quatro lotes, de acordo com a severidade de incidência de "bitter pit": nula (nenhuma lesão por fruto, baixa (1-2 lesões por fruto, moderada (3-4 lesões por fruto e alta (5-13 lesões por fruto. Foram determinados os teores de Ca, Mg, K e N na casca e na polpa em frutos individuais (doze frutos de cada lote. A análise univariada mostrou que os frutos com sintomas de "bitter pit" apresentaram menor teor de Ca na casca e na polpa, maior teor de K na casca e maiores valores das relações K/Ca, Mg/Ca, N/Ca, (K+Mg/Ca e (K+Mg+N/Ca, tanto na casca como na polpa. Todavia, quando todos os atributos nutricionais avaliados na casca e na polpa foram submetidos à análise canônica discriminante (análise multivariada, a melhor discriminação entre frutos sem "bitter pit" e frutos com severidade de incidência de "bitter pit" de baixa a alta é obtida com a relação K/Ca na casca, seguido, em menor grau, pelas relações Mg/Ca e N/Ca na polpa.The objective of this work was to identify nutritional attributes, assessed in the flesh and skin tissues, that provide a better discrimination regarding bitter pit severity in 'Gala' apples. After four months in regular cold storage (0-1°C; 90-95% RH, fruits were segregated into four lots with different levels of bitter pit severity: null (none pit per fruit, low (1-2 pits per fruit, moderate (3-4 pits per fruit, and high (5-13 pits per fruit. Nutritional analysis (Ca, Mg, K and N in the skin and in the flesh tissues were performed on twelve individual fruits of each severity level. The univariate analysis showed that fruits with bitter pit symptoms had lower concentration of Ca in the skin and flesh tissues, a

Borrowing brainpower - sharing insecurities

DEFF Research Database (Denmark)

Wegener, Charlotte; Meier, Ninna; Ingerslev, Karen

2016-01-01

Academic writing is a vital, yet complex skill that must be developed within a doctoral training process. In addition, becoming an academic researcher is a journey of changing sense of self and identity. Through analysis of a group session, we show how the feedback of peers addresses questions...... of structure and writing style along with wider issues of researcher identity. Thus, peer learning is demonstrated as a process of simultaneously building a text and an identity as scholarly researcher. The paper advocates ‘borrowing brainpower’ from peers in order to write better texts and, at the same time......, ‘share insecurities’ during the development of the researcher identity. Based on a distributed notion of peer learning and identity, we point to the need for further research into the everyday activities of doctoral writing groups in order to understand the dynamic relationship between production of text...

The Alberta oil sands story

Energy Technology Data Exchange (ETDEWEB)

1974-01-01

This report serves as a detailed introduction to the Alberta oil sands and their development. It includes a description of the oil sands deposits, an outline of crude bitumen recovery and upgrading processes, the role of Alberta Energy Company in oil sands development, environmental aspects, manpower requirements for oil sands development, research needs, and further oil sands projects. Presently proven recoverable reserves in the oil sands amount to 26.5 billion bbl of synthetic crude. Production from the Syncrude plant (125,000 bbl/d capacity) is expected to begin in 1977, followed by a Shell Canada operation around 1980. The provincial government will participate in the oil sand industry through its joint venture participation in Syncrude and its 50% share in Alberta Energy Company; the latter company participates in related aspects of the Syncrude project, such as pipelines. The result of Alberta's participation in the industry will mean that, directly or indirectly, the province will realize 60% of the total profits. The job creation potential of oil sands projects is estimated to be extensive, with a direct and indirect work force supported by oil sands activities possibly reaching 180,000 persons by the year 2000. Research needs have been identified, particularly in the area of in-situ thermal recovery technology, and the creation of the Alberta Oil Sands Technology and Research Authority has been authorized in order to meet these needs. Although current reserves are sufficient to support 20-30 synthetic crude plants, a number of factors will limit expansion of the industry. 8 figs., 5 tabs.

Micro pit formation by mercury-sphere collision

International Nuclear Information System (INIS)

Ishikura, Syuichi; Kogawa, Hiroyuki; Futakawa, Masatoshi; Kaminaga, Masanori; Hino, Ryutaro

2004-01-01

The development of a MW-class spallation neutron source facility is being carried out under the Japan Proton Accelerator Research Complex (J-PARC) Project promoted by JAERI and KEK. A mercury target working as the spallation neutron source will be subjected to pressure waves generated by rapid thermal expansion of mercury due to a pulsed proton beam injection. The pressure wave will impose dynamic stress on the vessel and deform the vessel, which would cause cavitation in mercury. To evaluate the effect of mercury micro jets, driven by cavitation bubble collapse, on the micro-pit formation, analyses on mercury sphere collision were carried out: single bubble dynamics and collision behavior on interface between liquid and solid, which take the nonlinearity due to shock wave in mercury and the strain rate dependency of yield stress in solid metal into account. Analytical results give a good explanation to understand relationship between the micro-pit formation and material properties: the pit size could decrease with increasing the yield strength of materials. (author)

42 CFR 60.15 - Other charges to the borrower.

Science.gov (United States)

2010-10-01

... fails to pay all of a required installment payment or fails to provide written evidence that verifies eligibility for the deferment of the payment within 30 days after the payment's due date, the lender or holder will require that the borrower pay a late charge. A late charge must be equal to 5 percent of the...

Relationship between foveal cone specialization and pit morphology in albinism.

Science.gov (United States)

Wilk, Melissa A; McAllister, John T; Cooper, Robert F; Dubis, Adam M; Patitucci, Teresa N; Summerfelt, Phyllis; Anderson, Jennifer L; Stepien, Kimberly E; Costakos, Deborah M; Connor, Thomas B; Wirostko, William J; Chiang, Pei-Wen; Dubra, Alfredo; Curcio, Christine A; Brilliant, Murray H; Summers, C Gail; Carroll, Joseph

2014-05-20

Albinism is associated with disrupted foveal development, though intersubject variability is becoming appreciated. We sought to quantify this variability, and examine the relationship between foveal cone specialization and pit morphology in patients with a clinical diagnosis of albinism. We recruited 32 subjects with a clinical diagnosis of albinism. DNA was obtained from 25 subjects, and known albinism genes were analyzed for mutations. Relative inner and outer segment (IS and OS) lengthening (fovea-to-perifovea ratio) was determined from manually segmented spectral domain-optical coherence tomography (SD-OCT) B-scans. Foveal pit morphology was quantified for eight subjects from macular SD-OCT volumes. Ten subjects underwent imaging with adaptive optics scanning light ophthalmoscopy (AOSLO), and cone density was measured. We found mutations in 22 of 25 subjects, including five novel mutations. All subjects lacked complete excavation of inner retinal layers at the fovea, though four subjects had foveal pits with normal diameter and/or volume. Peak cone density and OS lengthening were variable and overlapped with that observed in normal controls. A fifth hyper-reflective band was observed in the outer retina on SD-OCT in the majority of the subjects with albinism. Foveal cone specialization and pit morphology vary greatly in albinism. Normal cone packing was observed in the absence of a foveal pit, suggesting a pit is not required for packing to occur. The degree to which retinal anatomy correlates with genotype or visual function remains unclear, and future examination of larger patient groups will provide important insight on this issue. Copyright 2014 The Association for Research in Vision and Ophthalmology, Inc.

Optimizing the physical conditioning of the NASCAR sprint cup pit crew athlete.

Science.gov (United States)

Ferguson, David P; Davis, Adam M; Lightfoot, J Timothy

2015-03-01

Stock car racing is the largest spectator sport in the United States. As a result, National Association for Stock Car Automobile Racing (NASCAR) Sprint Cup teams have begun to invest in strength and conditioning programs for their pit crew athletes. However, there is limited knowledge regarding the physical characteristics of elite NASCAR pit crew athletes, how the NASCAR Sprint Cup season affects basic physiological parameters such as body composition, and what is the most appropriate physical training program that meets the needs of a pit crew athlete. We conducted 3 experiments involving Sprint Cup motorsport athletes to determine predictors of success at the elite level, seasonal physiological changes, and appropriate physical training programs. Our results showed that hamstring flexibility (p = 0.015) and the score on the 2-tire front run test (p = 0.012) were significant predictors of NASCAR Sprint Cup Pit Crew athlete performance. Additionally, during the off season, pit crew athletes lost lean body mass, which did not return until the middle of the season. Therefore, a strength and conditioning program was developed to optimize pit crew athlete performance throughout the season. Implementation of this strength and conditioning program in 1 NASCAR Sprint Cup team demonstrated that pit crew athletes were able to prevent lean body mass loss and have increased muscle power output from the start of the season to the end of the season.

The phenomenon of prehistoric ritual pits: Several examples from the central Balkans

Directory of Open Access Journals (Sweden)

Bulatović Aleksandar P.

2015-01-01

Full Text Available In recent years, the phenomenon of pits with special deposits, i.e. ritual pits, seems to have, once again, attracted attention both in Europe and in the Balkans. In the central Balkans, scientific literature related to this topic is still deficient, hence one of the objectives of this paper is to change the current state and rekindle interest in the study of this form of manifestation of the spiritual culture of prehistoric man. It appears that one of the oldest reasons for sacrificial offerings is primal, instinctive fear. The fear of the transience of life or of death compelled our ancient ancestors to make some sort of “agreement” with the surrounding forces, bestowing particular sacrifices onto them. Sacrifice represents one of the rituals of prehistoric communities which could have been performed in a number of ways and in different circumstances. One of these are offerings placed in pits, in the form of specific objects, food, drink or living beings sacrificed to higher powers and accompanied by certain symbolic actions, for the purpose of gaining their favour or help. When interpreting pits, what should further be considered is that the fundamental difference between a discarded object and an object used for a ritual purpose lies in the fact that the object of ritual character is still meaningful to man, performing a symbolic function, unlike the former, whose role is lost after being disposed of. Aritual object, an item or a living being sacrificed in a pit, is no longer of common, worldly significance (food, drink, tools, etc., but rather possesses a symbolic, sacral meaning, intended for higher powers, to propitiate and appease them, that is to create some form of the oldest religious communication. Not only is it difficult to identify the pits used for ritual purposes in the course of fieldwork, but it is even more challenging to interpret them and practically impossible to accurately reconstruct the actions performed during the

Herniation pits of the femur neck: incidence and radiologic findings

International Nuclear Information System (INIS)

Cho, Jae Hyun; Suh, Jin Suk; Lee, Hye Yeon

1994-01-01

In order to assess the incidence and radiologic findings of herniation pit of the femur neck in Korean. In 152 macerated femurs of 88 cadavers, and randomly selected 115 hips of 70 patients, the presence of herniation pit was determined by using fluoroscopy and radiography. It was then examined by CT for inspection of overlying surface and its opening was confirmed by inserting thin steal wire under the fluoroscopic guidance. Seventeen herniation pits in 15 macerated femurs of 13 cadavers were noted. (14.8%, 13/88). Two of 13 individuals showed bilaterality. All lesions were found only in males. Six herniation pit in 6 femurs of 6 patients (8.6%, 6/70) were also noted. All lesions were on anterosuperior aspect of femur neck. Plain radiographs of macerated femurs revealed well marginated and thin sclerosis in 15 lesions. Of all 23 lesions, CT showed cortical breakdown in 3, and overlying cortical thickening in 8. In 15 macerated femurs, roughed area of cortex was found in anterosuperior aspect of femur in all cases, and tiny openings(diameter less than 1 mm) related to cystic lesions were confirmed in 9 lesions. The incidence of herniation pits was 14.8% in 88 cadaver, and 8.6% in 70 patients. All were males

Offshore Sand Resource Needs, Data Availability and Revaluation, and Beach Nourishment Projects in North Carolina

Science.gov (United States)

Conery, I.; Walsh, J. P.

2016-12-01

Storms and sea-level rise continue to impact the dynamic coastlines of North Carolina. Since the coastal region is economically critical to the state and yields numerous ecosystem services, many towns have planned beach nourishment projects. However, offshore sands compatible for nourishment are limited, and project costs fluctuate with borrow source proximity to the shoreline. Hurricane Sandy (2012) caused high water levels and waves resulting in localized overwash and erosion in the northeastern part of NC. In response, to effectively meet the rising nourishment demands for recovery after future storm events and for long-term resiliency, the Bureau of Ocean Energy Management (BOEM) recognized the need to compile and consolidate all geophysical and geologic information in federal waters (3-8 nm) along the East Coast states. A GIS database was created for NC using bathymetric, seismic reflection, sediment and other relevant data from federal, state and private entities. Information will be accessible to the public, coastal planners and managers to allow for informed decision-making and cost-effective project planning. Priority regions for seismic and core collection were determined based on data gaps and needs across the state. In addition, potential sand resource thickness and volume in northeastern NC were revaluated using comparisons of several overlapping datasets. Shoreline volume losses were calculated using long-term erosion rates and compared to historic and future nourishment projects. Finally, tourism-based revenue by town was evaluated and related to short and long-term nourishment costs.

The Third Pillar of the Basel Accord: Evidence of borrower discipline in the Kyrgyz banking system

Directory of Open Access Journals (Sweden)

Edgar Demetrio Tovar-García

2016-07-01

Full Text Available We empirically study the asset side of market discipline in the banking system of the Kyrgyz Republic, examining whether borrowers are willing to pay higher interest rates to high-quality banks. Based on dynamic panel models and a dataset with bank information from 23 banks over the period 2010–2012, our findings suggest the presence of market discipline induced by borrowers. In other words, banks with higher capital ratios and liquidity charge higher interest rates on loans. This result has several implications for the banking policy in Kyrgyzstan, where we can recommend to policymakers a disclosure policy following the Third Pillar of Basel III, because not only can the bank's creditors use bank information to penalize the excessive bank risk, but borrowers can also use this information to discipline their banks.

Investigation of the pitting of aluminum induced by chloride ions by holographic microphotography

Directory of Open Access Journals (Sweden)

LIANG LI

2008-05-01

Full Text Available Holographic microphotography was used to investigate the dynamic processes of pitting during anodic dissolution of aluminum in a solution containing chloride ions. The induction and the follow-up propagation processes of the pitting were observed in real-time. A simple model of the propagating process of the pitting was deduced from the result of the holograms of the Al/electrolyte interface. The results prove that holographic microphotography is a useful tool to study the dynamic processes of pitting.

Dependence of Crystallographic Orientation on Pitting Corrosion Behavior of Ni-Fe-Cr Alloy 028

Science.gov (United States)

Zhang, LiNa; Szpunar, Jerzy A.; Dong, JianXin; Ojo, Olanrewaju A.; Wang, Xu

2018-03-01

The influence of crystallographic orientation on the pitting corrosion behavior of Ni-Fe-Cr alloy 028 was studied using a combination of X-ray diffraction (XRD), electron backscatter diffraction (EBSD), potentiodynamic polarization technique, and atomic force microscopy (AFM). The results show that there is anisotropy of pitting corrosion that strongly depends on crystallographic orientation of the surface plane. The distribution of pit density in a standard stereographic triangle indicates that the crystallographic planes close to {100} are more prone to pitting corrosion compared to planes {110} and {111}. The surface energy calculation of (001) and (111) shows that the plane with a high atomic packing density has a low surface energy with concomitant strong resistance to pitting corrosion. A correlation function between crystallographic orientation and pitting corrosion susceptibility suggests a method that not only predicts the pitting resistance of known textured materials, but also could help to improve corrosion resistance by controlling material texture.

Stochastic modeling of inspection uncertainties and applications to pitting flaws in steam generator tubes

International Nuclear Information System (INIS)

Mao, D.; Yuan, X.-X.; Pandey, M.D.

2009-01-01

Steam generators (SG) are a major pressure retaining component of great safety significance in nuclear power plants. Due to various manufacturing, operation and maintenance activities, as well as material interaction with the surrounding chemical environment, the SG tubes have been subject to a number of degradation modes. Among them, the under-deposit pitting corrosion at outside surfaces of the SG tubes just on top of the tubesheet support plates has had a serious impact on the integrity of the SG tubes. This paper presents an advanced probabilistic model of pitting corrosion characterizing the inherent randomness of the pitting process and measurement uncertainties of the in-service inspection (ISI) data obtained from eddy current (EC) inspections. A Bayesian method based on Markov Chain Monte Carlo (MCMC) simulation is developed for estimating the model parameters. The proposed model is able to predict the actual pit number, the actual pit depth as well as the maximum pit depth, which is the main interest of the pitting corrosion model. (author)

Open pit mining of uranium

International Nuclear Information System (INIS)

Wood, J.T.

1977-01-01

The Jackpile--Paquate Mines of the Anaconda Company are on the Laguna Indian Reservation midway between Grants and Albuquerque, New Mexico. The open pit mining of uranium ore at those mines is conducted in three separate operations (stripping, mining, and ore haul)

Creating Nanoscale Pits on Solid Surfaces in Aqueous Environment with Scanning Tunnelling Microscopy

DEFF Research Database (Denmark)

Chi, Qijin; Zhang, Jingdong; Friis, Esben P.

2000-01-01

of the pits can be controlled well in aqueous environments, and the operations are simple. Parameters affecting the pit formation and size have been systematically characterized to show that pit formation is dominated by bias voltage. A mechanism is proposed based on local surface reconstruction induced...

Additional disturbances as a beneficial tool for restoration of post-mining sites: a multi-taxa approach.

Science.gov (United States)

Řehounková, Klára; Čížek, Lukáš; Řehounek, Jiří; Šebelíková, Lenka; Tropek, Robert; Lencová, Kamila; Bogusch, Petr; Marhoul, Pavel; Máca, Jan

2016-07-01

Open interior sands represent a highly threatened habitat in Europe. In recent times, their associated organisms have often found secondary refuges outside their natural habitats, mainly in sand pits. We investigated the effects of different restoration approaches, i.e. spontaneous succession without additional disturbances, spontaneous succession with additional disturbances caused by recreational activities, and forestry reclamation, on the diversity and conservation values of spiders, beetles, flies, bees and wasps, orthopterans and vascular plants in a large sand pit in the Czech Republic, Central Europe. Out of 406 species recorded in total, 112 were classified as open sand specialists and 71 as threatened. The sites restored through spontaneous succession with additional disturbances hosted the largest proportion of open sand specialists and threatened species. The forestry reclamations, in contrast, hosted few such species. The sites with spontaneous succession without disturbances represent a transition between these two approaches. While restoration through spontaneous succession favours biodiversity in contrast to forestry reclamation, additional disturbances are necessary to maintain early successional habitats essential for threatened species and open sand specialists. Therefore, recreational activities seem to be an economically efficient restoration tool that will also benefit biodiversity in sand pits.

Numerical Simulation of Interactions between Corrosion Pits on Stainless Steel under Loading Conditions

International Nuclear Information System (INIS)

Wang, Haitao; Han, En-Hou

2017-01-01

The interactions between corrosion pits on stainless steel under loading conditions are studied by using a cellular automata model coupled with finite element method at a mesoscopic scale. The cellular automata model focuses on a metal/film/electrolyte system, including anodic dissolution, passivation, diffusion of hydrogen ions and salt film hydrolysis. The Chopard block algorithm is used to improve the diffusion simulation efficiency. The finite element method is used to calculate the stress concentration on the pit surface during pit growth, and the effect of local stress and strain on anodic current is obtained by using the Gutman model, which is used as the boundary conditions of the cellular automata model. The transient current characteristics of the interactions between corrosion pits under different simulation factors including the breakdown of the passive film at the pit mouth and the diffusion of hydrogen ions are analyzed. The analysis of the pit stability product shows that the simulation results are close to the experimental conclusions.

Electronic structures of GeSi nanoislands grown on pit-patterned Si(001 substrate

Directory of Open Access Journals (Sweden)

Han Ye

2014-11-01

Full Text Available Patterning pit on Si(001 substrate prior to Ge deposition is an important approach to achieve GeSi nanoislands with high ordering and size uniformity. In present work, the electronic structures of realistic uncapped pyramid, dome, barn and cupola nanoislands grown in {105} pits are systematically investigated by solving Schrödinger equation for heavy-hole, which resorts to inhomogeneous strain distribution and nonlinear composition-dependent band parameters. Uniform, partitioned and equilibrium composition profile (CP in nanoisland and inverted pyramid structure are simulated separately. We demonstrate the huge impact of composition profile on localization of heavy-hole: wave function of ground state is confined near pit facets for uniform CP, at bottom of nanoisland for partitioned CP and at top of nanoisland for equilibrium CP. Moreover, such localization is gradually compromised by the size effect as pit filling ratio or pit size decreases. The results pave the fundamental guideline of designing nanoislands on pit-patterned substrates for desired applications.

Numerical Simulation of Interactions between Corrosion Pits on Stainless Steel under Loading Conditions

Energy Technology Data Exchange (ETDEWEB)

Wang, Haitao; Han, En-Hou [Chinese Academy of Sciences, Shenyang (China)

2017-04-15

The interactions between corrosion pits on stainless steel under loading conditions are studied by using a cellular automata model coupled with finite element method at a mesoscopic scale. The cellular automata model focuses on a metal/film/electrolyte system, including anodic dissolution, passivation, diffusion of hydrogen ions and salt film hydrolysis. The Chopard block algorithm is used to improve the diffusion simulation efficiency. The finite element method is used to calculate the stress concentration on the pit surface during pit growth, and the effect of local stress and strain on anodic current is obtained by using the Gutman model, which is used as the boundary conditions of the cellular automata model. The transient current characteristics of the interactions between corrosion pits under different simulation factors including the breakdown of the passive film at the pit mouth and the diffusion of hydrogen ions are analyzed. The analysis of the pit stability product shows that the simulation results are close to the experimental conclusions.

Compressive behavior of fine sand.

Energy Technology Data Exchange (ETDEWEB)

Martin, Bradley E. (Air Force Research Laboratory, Eglin, FL); Kabir, Md. E. (Purdue University, West Lafayette, IN); Song, Bo; Chen, Wayne (Purdue University, West Lafayette, IN)

2010-04-01

The compressive mechanical response of fine sand is experimentally investigated. The strain rate, initial density, stress state, and moisture level are systematically varied. A Kolsky bar was modified to obtain uniaxial and triaxial compressive response at high strain rates. A controlled loading pulse allows the specimen to acquire stress equilibrium and constant strain-rates. The results show that the compressive response of the fine sand is not sensitive to strain rate under the loading conditions in this study, but significantly dependent on the moisture content, initial density and lateral confinement. Partially saturated sand is more compliant than dry sand. Similar trends were reported in the quasi-static regime for experiments conducted at comparable specimen conditions. The sand becomes stiffer as initial density and/or confinement pressure increases. The sand particle size become smaller after hydrostatic pressure and further smaller after dynamic axial loading.

The Use of Pit and Fissure Sealants—A Literature Review

Directory of Open Access Journals (Sweden)

Reem Naaman

2017-12-01

Full Text Available This paper reviews the literature and discusses the latest updates on the use of pit and fissure sealants. It demonstrates the effectiveness of pit and fissure sealants in preventing caries and the management of early carious lesions. It compares the use of different sealant materials and their indications. It describes the application technique for sealants. It also reviews the cost-effectiveness of sealants as a preventive strategy. From this review and after the discussion of recently published studies on pit and fissure sealants, it is evident that sealants are effective in caries prevention and in preventing the progression of incipient lesions. It is therefore recommended that pit and fissure sealant be applied to high-caries-risk children for optimum cost-effectiveness. It is a highly sensitive technique that needs optimum isolation, cleaning of the tooth surface, etching, and the application of a thin bonding layer for maximum benefit. Recall and repair, when needed, are important to maximize the effectiveness of such sealant use.

The Use of Pit and Fissure Sealants—A Literature Review

Science.gov (United States)

Naaman, Reem; El-Housseiny, Azza A.; Alamoudi, Najlaa

2017-01-01

This paper reviews the literature and discusses the latest updates on the use of pit and fissure sealants. It demonstrates the effectiveness of pit and fissure sealants in preventing caries and the management of early carious lesions. It compares the use of different sealant materials and their indications. It describes the application technique for sealants. It also reviews the cost-effectiveness of sealants as a preventive strategy. From this review and after the discussion of recently published studies on pit and fissure sealants, it is evident that sealants are effective in caries prevention and in preventing the progression of incipient lesions. It is therefore recommended that pit and fissure sealant be applied to high-caries-risk children for optimum cost-effectiveness. It is a highly sensitive technique that needs optimum isolation, cleaning of the tooth surface, etching, and the application of a thin bonding layer for maximum benefit. Recall and repair, when needed, are important to maximize the effectiveness of such sealant use. PMID:29563440

Influence of remanent magnetization on pitting corrosion in pipeline steel

Energy Technology Data Exchange (ETDEWEB)

Espina-Hernandez, J. H. [ESIME Zacatenco, SEPI Electronica Instituto Politecnico Nacional Mexico, D. F. (Mexico); Caleyo, F.; Hallen, J. M. [DIM-ESIQIE, Instituto Politecnico Nacional Mexico D. F. (Mexico); Lopez-Montenegro, A.; Perez-Baruch, E. [Pemex Exploracion y Produccion, Region Sur Villahermosa, Tabasco (Mexico)

2010-07-01

Statistical studies performed in Mexico indicate that leakage due to external pitting corrosion is the most likely cause of failure of buried pipelines. When pipelines are inspected with the magnetic flux leakage (MFL) technology, which is routinely used, the magnetization level of every part of the pipeline changes as the MFL tool travels through it. Remanent magnetization stays in the pipeline wall after inspection, at levels that may differ from a point to the next. This paper studies the influence of the magnetic field on pitting corrosion. Experiments were carried out on grade 52 steel under a level of remanent magnetization and other laboratory conditions that imitated the conditions of a pipeline after an MLF inspection. Non-magnetized control samples and magnetized samples were subjected to pitting by immersion in a solution containing chlorine and sulfide ions for seven days, and then inspected with optical microscopy. Results show that the magnetic field in the pipeline wall significantly increases pitting corrosion.

Using social impact borrowing to expand preschool through third grade programs in urban public schools.

Science.gov (United States)

Temple, Judy A; Reynolds, Arthur J

Budget constraints and difficulty raising taxes limit school districts from expanding education programming even when research shows that additional expenditures would generate economic benefits that are greater than costs. Recently, coalitions of private investors, philanthropists, education practitioners, and government finance analysts have emerged to create opportunities to expand education services that promise high rates of social net benefits without raising taxes or reducing other expenditures. These collaborators have a strong interest in obtaining careful estimates of educational program effectiveness. We describe the use of social-impact borrowing to increase access to the Child-Parent Center preschool-through-third-grade intervention for at-risk students in the Chicago Public School District. The partners include the city, school district, investors, nonprofit organizations, and a university. The key to the feasibility of social-impact borrowing is the ability to document that early intervention can reduce the need for later special-education services. With the help of private investors and nonprofit organizations, it is possible for public school districts to finance services with funds from private sources and use future cost savings to repay this debt. We discuss how social-impact borrowing is being used in Chicago and in Salt Lake County as the nation's first two instances of using pay-for-performance social-impact borrowing to support early education.

New Generation Energy Efficient Refractory Application in Soaking Pits of Bhilai Steel Plant, Sail

Science.gov (United States)

Roy, Indranil; Chintaiah, Perumetla; Bhattacharya, Ajoy Kr.; Garai, Swapan Kr.; Ray Choudhury, Pankaj Kr.; Tiwari, Laksman

In Bhilai Steel Plant (BSP), soaking pits are used for heating ingots for successive rolling into blooms. Pits are operated at a temperature of around 1350°C. Mixed gas (Mixture of Blast Furnace gas & Coke Oven gas) of calorific value around 2040 kcal/Nm3 is used as fuel. The walls of soaking pits were lined with traditional 38% Al2O3 firebricks and top 500mm was cast with 70% Al2O3 low cement castable (LCC). This type of lining results in frequent damages due to hitting by ingots while being lifted from pit by overhead cranes thus affecting the availability of pit. Life of pits was 2 to 2.5 years in BSP with 3-4 cold repairs and 3-4 hot repairs. Energy loss through the wall is also quite high in this type of lining. To triumph over the limitations of the conventional lining, a lining design was developed for the walls which consist of special 70% Al2O3 LCC having high hot strength (HMOR) in combination with specially design flexible SS-304 anchors. Ceramic fiber blanket and insulation bricks were provided between castable and the metallic shell of the pit to minimize the heat loss. A heating schedule was developed and introduced based on available infrastructure at BSP for proper curing of modified LCC based lining. After introduction of modified lining, pit no. 14/2 is running for more than 2.5 years without any repair. To capitalize the success, two more pits i.e. 12/1 and 9/2 were converted to modified lining. These pits are also running satisfactorily for more than 1.5 years. The modification has resulted in higher availability with substantial increase in production. Shell temperature of the modified pits reduced to 90° - 140°C from 120° - 200°C of conventional pits. This shows reduction in heat loss through walls, resulting less fuel consumption and energy saving of about 18%.

7 CFR 1724.70 - Standard forms of contracts for borrowers.

Science.gov (United States)

2010-01-01

... required to use in the planning, design, and construction of their electric systems. Borrowers are not required to use these guidance contract forms in the absence of an agreement to do so. [63 FR 58284, Oct... construction, procurement, engineering services, and architectural services financed by a loan made or...

Heart rate and core temperature responses of elite pit crews during automobile races.

Science.gov (United States)

Ferguson, David P; Bowen, Robert S; Lightfoot, J Timothy

2011-08-01

There is limited information regarding the physiological and psychological demands of the racing environment, and the subsequent effect on the performance of pit crew athletes. The purpose of this study was to evaluate heart rates (HRs) and core body temperatures (CTs) of pit crew athletes in the race environment. The HR and CT of pit crew athletes (n = 7) and control subjects were measured during 6 National Association for Stock Car Automobile Racing Sprint Cup races using ingestible sensors (HQ Inc, Palmetto, FL, USA). The HR and CT were measured before each race, at 15-minute intervals during the race, and upon completion of each pit stop. Compared to the control subject at each race, the pit crew athletes had significantly (p = 0.014) lower core temperatures (CTs). The pit crew athletes displayed higher HRs on the asphalt tracks than on concrete tracks (p = 0.011), and HR responses of the crew members were significantly (p = 0.012) different between pit crew positions, with the tire changers and jackman exhibiting higher HRs than the tire carriers. Unexpectedly, the CTs of the pit crew athletes were not elevated in the race environment, despite high ambient temperatures and the extensive fire-protection equipment (e.g., helmet, suit, gloves) each pit crew athlete wore. The lack of CT change is possibly the result of the increased HR more efficiently shunting blood to the skin and dissipating heat as a consequence of the athletes' extensive training regimen and ensuing heat acclimation. Additionally, it is possible that psychological stress unique to several of the tracks provided an additive effect resulting in increased heart rates.

Plantar pitted keratolysis: a study from non-risk groups

Directory of Open Access Journals (Sweden)

Asli Feride Kaptanoglu

2012-02-01

Full Text Available Pitted keratolysis is an acquired, superficial bacterial infection of the skin which is characterized by typical malodor and pits in the hyperkeratotic areas of the soles. It is more common in barefooted people in tropical areas, or those who have to wear occlusive shoes, such as soldiers, sailors and athletes. In this study, we evaluated 41 patients who had been diagnosed with plantar pitted keratolysis. The patients were of high socioeconomic status, were office-workers, and most had a university degree. Malodor and plantar hyperhydrosis were the most frequently reported symptoms. The weight-bearing metatarsal parts of the feet were those most affected. Almost half the women in the study gave a history of regular pedicure and foot care in a spa salon. Mean treatment duration was 19 days. All patients were informed about the etiology of the disease, predisposing factors and preventive methods. Recurrences were observed in only 17% of patients during the one year follow-up period. This study emphasizes that even malodorous feet among non-risk city dwellers may be a sign of plantar pitted keratolysis. A study of the real incidence of the disease in a large population-based series is needed.

Effect of nitrite concentration on pit depth in carbon steel exposed to simulated radioactive waste

International Nuclear Information System (INIS)

Zapp, P.E.

1997-01-01

The growth of pits in carbon steel exposed to dilute (0.055 M nitrate-bearing) alkaline salt solutions that simulate radioactive waste was investigated in coupon immersion tests. Most coupons were tested in the as-received condition, with the remainder having been heat treated to produce an oxide film. Nitrite, which is an established pitting inhibitor in these solutions, was present in concentrations from 0 to 0.031 M to 0.16 M; the last concentration is known to prevent pitting initiation in the test solution at the 50 degrees C test temperature. The depths of the deepest pits on coupons of particular exposure conditions were measure microscopically and were analyzed as simple, type 1 extreme value statistical distributions, to predict the deepest expected pit in a radioactive waste tank subject to the test conditions. While the growth rate of pits could not be established from these tests, the absolute value of the deepest pits predicted is of the order of 100 mils after 448 days of exposure. The data indicate that even nitrite concentrations insufficient to prevent pitting have a beneficial effect on limiting the growth of deepest pits

25 CFR 103.34 - What if the lender and borrower decide to change the terms of the loan?

Science.gov (United States)

2010-04-01

... identity or organizational structure of the borrower. (5) Allow any material change in the use of loan proceeds or the nature of the borrower's business. (6) Release any collateral taken as security for the loan, except items sold in the ordinary course of business and promptly replaced by similar items of...

Rationale and concept for a lunar pit reconnaissance probe

Science.gov (United States)

Dorrington, G. E.

2018-04-01

Speculation on near-term scientific reasons for the exploration of lunar pits is offered alongside comments on possible longer-term human exploitation. It is proposed that in order to determine whether or not one or more of the pits offer access the large subsurface voids e.g. a non-collapsed lava tube, a preliminary reconnaissance mission solely focused on obtaining lateral images (and/or LiDAR maps) is needed. Possible concept options for such a preliminary reconnaissance mission are discussed. It is suggested that one of the best possible strategies is to employ a micro-sized probe (∼0.3m) that would hop from a nearby main landing spacecraft to the selected pit. After the surface position of the main lander is determined accurately, the probe would perform a ballistic hop, or hover-traverse, a distance of ∼3 km over the lunar surface using existing propulsive and guidance technology capability. Once hovering above the pit, the probe or a separate tethered imaging unit would then be lowered into the pit to acquire the necessary subsurface void topology data. This data would then be transmitted back to Earth, directly, via the lander, or via a store-and-forward orbiting relay. Preliminary estimates indicate that a probe of ∼14 kg (dry mass) is viable using a conventional hydrazine monopropellant system with a propellant mass fraction of less than ∼0.2 (20%) including margins, suggesting a piggyback architecture would be feasible.

Pitting of 3003 aluminum

International Nuclear Information System (INIS)

Lee, R.

1996-01-01

The Advanced Photon Source is a state-of-the-art synchrotron light source. The storage ring vacuum chamber is fabricated from 6061 extruded Al. Water connections to the vacuum chambers that were fabricated from 3003 Al had developed water leaks, which were subsequently remedied after considerable investigations. Materials subjected to the pitting analysis in this study are 3003, 6061, and 6063 Al

Criticality analysis for weapon disassembly at the Pantex Plant - part I: Bare pits

Energy Technology Data Exchange (ETDEWEB)

Knief, R.A. [Ogden Environmental & Energy Services, Albuquerque, NM (United States)

1997-06-01

This paper briefly describes criticality investigations for weapon assembly and dismantlement at the Pantex Plant. Results are summarized for calculations performed for safety analyses, radiological hazards assessments, and a study to justify the criticality alarm exemption. Pits and pits in containers were modeled in their most reactive configuration. Criticality calculations were performed with the KENO and MCNP code packages. Configurations involving bare pits were subcritical by a substantial amount even with very conservative model assumptions. Thus, it is concluded that a critical configuration involving the bare pits is not credible.

Mud Pit Risk-Based Closure Strategy Report, Nevada Test Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Brain Hoenes

2004-08-01

This report presents the findings of the human and ecological risk assessment for the NTS mud pits. The risk assessment utilizes data from 52 of the 270 NTS mud pits in conjunction with corroborative data from 87 other DOE mud pits associated with nuclear testing (at locations on the NTS, in the western United States, and Alaska) as well as relevant process knowledge. Based on the risk assessment findings, the report provides a strategy for further evaluation, characterization, and closure of all 270 NTS mud pit CASs using the Streamlined Approach for Environmental Restoration (SAFER).

Changes in energy metabolism accompanying pitting in blueberries stored at low temperature.

Science.gov (United States)

Zhou, Qian; Zhang, Chunlei; Cheng, Shunchang; Wei, Baodong; Liu, Xiuying; Ji, Shujuan

2014-12-01

Low-temperature storage and transport of blueberries is widely practiced in commercial blueberry production. In this research, the storage life of blueberries was extended at low temperature, but fruit stored for 30 d at 0°C pitted after 2d at room-temperature. Fruit cellular structure and physiological parameters accompanying pitting in blueberries were changed. The objective of this research was to characterise properties of energy metabolism accompanying pitting in blueberries during storage, including adenosine phosphates and mitochondrial enzymes involved in stress responses. Physiological and metabolic disorders, changes in cell ultrastructure, energy content and ATPase enzyme activity were observed in pitting blueberries. Energy shortages and increased activity of phenylalanine ammonia lyase (PAL) and lipoxygenase (LOX) were observed in fruit kept at shelf life. The results suggested that sufficient available energy status and a stable enzymatic system in blueberries collectively contribute to improve chilling tolerance, thereby alleviating pitting and maintaining quality of blueberry fruit in long-term cold storage. Copyright © 2014 Elsevier Ltd. All rights reserved.

Situation and development of uranium open-pit mining techniques in China

International Nuclear Information System (INIS)

Li Kaiwen.

1986-01-01

The situation of uranium open-pit mining techniques in China is described. The main experiences in production and management are introduced. Meanwhile the suggestions about the further development of uranium open-pit mining techniques are also proposed

Pit disassembly and conversion demonstration environmental assessment and research and development activities

International Nuclear Information System (INIS)

1998-08-01

A significant portion of the surplus plutonium is in the form of pits, a nuclear weapons component. Pits are composed of plutonium which is sealed in a metallic shell. These pits would need to be safely disassembled and permanently converted to an unclassified form that would be suitable for long-term disposition and international inspection. To determine the feasibility of an integrated pit disassembly and conversion system, a Pit Disassembly and Conversion Demonstration is proposed to take place at the Los Alamos National Laboratory (LANL). This demonstration would be done in existing buildings and facilities, and would involve the disassembly of up to 250 pits and conversion of the recovered plutonium to plutonium metal ingots and plutonium dioxide. This demonstration also includes the conversion of up to 80 kilograms of clean plutonium metal to plutonium dioxide because, as part of the disposition process, some surplus plutonium metal may be converted to plutonium dioxide in the same facility as the surplus pits. The equipment to be used for the proposed demonstration addressed in this EA would use some parts of the Advanced Recovery and Integrated Extraction System (ARIES) capability, other existing equipment/capacities, plus new equipment that was developed at other sites. In addition, small-scale R and D activities are currently underway as part of the overall surplus plutonium disposition program. These R and D activities are related to pit disassembly and conversion, MOX fuel fabrication, and immobilization (in glass and ceramic forms). They are described in Section 7.0. On May 16, 1997, the Office of Fissile Materials Disposition (MD) notified potentially affected states and tribes that this EA would be prepared in accordance with NEPA. This EA has been prepared to provide sufficient information for DOE to determine whether a Finding of No Significant Impact (FONSI) is warranted or whether an EIS must be prepared

Pits, rifts and slumps: the summit structure of Piton de la Fournaise

Science.gov (United States)

Carter, Adam; van Wyk de Vries, Benjamin; Kelfoun, Karim; Bachèlery, Patrick; Briole, Pierre

2007-06-01

A clear model of structures and associated stress fields of a volcano can provide a framework in which to study and monitor activity. We propose a volcano-tectonic model for the dynamics of the summit of Piton de la Fournaise (La Reunion Island, Indian Ocean). The summit contains two main pit crater structures (Dolomieu and Bory), two active rift zones, and a slumping eastern sector, all of which contribute to the actual fracture system. Dolomieu has developed over 100 years by sudden large collapse events and subsequent smaller drops that include terrace formation. Small intra-pit collapse scars and eruptive fissures are located along the southern floor of Dolomieu. The western pit wall of Dolomieu has a superficial inward dipping normal fault boundary connected to a deeper ring fault system. Outside Dolomieu, an oval extension zone containing sub-parallel pit-related fractures extends to a maximum distance of 225 m from the pit. At the summit the main trend for eruptive fissures is N80°, normal to the north south rift zone. The terraced structure of Dolomieu has been reproduced by analogue models with a roof to width ratio of approximately 1, suggesting an original magma chamber depth of about 1 km. Such a chamber may continue to act as a storage location today. The east flank has a convex concave profile and is bounded by strike-slip fractures that define a gravity slump. This zone is bound to the north by strike-slip fractures that may delineate a shear zone. The southern reciprocal shear zone is probably marked by an alignment of large scoria cones and is hidden by recent aa lavas. The slump head intersects Dolomieu pit and may slide on a hydrothermally altered layer known to be located at a depth of around 300 m. Our model has the summit activity controlled by the pit crater collapse structure, not the rifts. The rifts become important on the mid-flanks of the cone, away from pit-related fractures. On the east flank the superficial structures are controlled

From Passive to Proactive: Understanding and Improving the Borrower Experience with Online Student Loan Exit Counseling. Research Report

Science.gov (United States)

Fernandez, Chris

2015-01-01

Legally mandated student loan exit counseling attempts to prepare borrowers of federal student loans for the repayment process; yet, researchers hypothesized that the online modules most borrowers use for this purpose have significant shortcomings. This report (the second in a series of five from TG Research) describes a study in which researchers…

Mycotoxin occurrence on baled and pit silages collected in Co. Meath

Directory of Open Access Journals (Sweden)

McElhinney C.

2015-12-01

Full Text Available Recent studies of baled silages produced in Ireland have identified considerable filamentous fungal contamination. Many of these fungi are toxigenic, capable of producing secondary metabolites, namely mycotoxins. Mycotoxins are potentially detrimental to livestock health and some can pose a risk to consumers of animal products. Baled (n=20 and pit (n=18 silages from a sample of farms (n=38 in Co. Meath were examined to assess the occurrence of mycotoxins and ascertain whether sampling position within the pit silos (feed face vs. 3 m behind the feed face has an effect on mycotoxin content or other chemical compositional variables. Of the 20 mycotoxins assayed, baled silages contained [mean of positive values (no. of values in mean] mycotoxin concentrations (μg/kg dry matter of beauvericin 36 (2, enniatin (enn. A 9.3 (3, enn. A1 54 (8, enn. B 351 (9, enn. B1 136 (10, mycophenolic acid (MPA 11,157 (8 and roquefortine C (Roq. C 1037 (8 and pit silages contained beauvericin 25 (2 enn. A1 18 (2, enn. B 194 (9, enn. B1 57 (3, MPA 287 (6, Roq. C 3649 (6 and zearalenone 76 (1. There was no difference (P>0.05 observed in the mycotoxin concentrations between baled and pit silages, and 11 of the 20 mycotoxins assayed were below the limits of detection. The position of sampling had no effect on the mycotoxin concentration detected in pit silages. It is concluded that mycotoxin concentrations detected in these pit and baled silages in Co. Meath did not exceed EU regulation or guidance limits, and that similar chemical composition and mycotoxin concentration values occurred at the pit silage feed face and 3 m behind this feed face.

Fine root dynamics in lodgepole pine and white spruce stands along productivity gradients in reclaimed oil sands sites.

Science.gov (United States)

Jamro, Ghulam Murtaza; Chang, Scott X; Naeth, M Anne; Duan, Min; House, Jason

2015-10-01

Open-pit mining activities in the oil sands region of Alberta, Canada, create disturbed lands that, by law, must be reclaimed to a land capability equivalent to that existed before the disturbance. Re-establishment of forest cover will be affected by the production and turnover rate of fine roots. However, the relationship between fine root dynamics and tree growth has not been studied in reclaimed oil sands sites. Fine root properties (root length density, mean surface area, total root biomass, and rates of root production, turnover, and decomposition) were assessed from May to October 2011 and 2012 using sequential coring and ingrowth core methods in lodgepole pine (Pinus contorta Dougl.) and white spruce (Picea glauca (Moench.) Voss) stands. The pine and spruce stands were planted on peat mineral soil mix placed over tailings sand and overburden substrates, respectively, in reclaimed oil sands sites in Alberta. We selected stands that form a productivity gradient (low, medium, and high productivities) of each tree species based on differences in tree height and diameter at breast height (DBH) increments. In lodgepole pine stands, fine root length density and fine root production, and turnover rates were in the order of high > medium > low productivity sites and were positively correlated with tree height and DBH and negatively correlated with soil salinity (P < 0.05). In white spruce stands, fine root surface area was the only parameter that increased along the productivity gradient and was negatively correlated with soil compaction. In conclusion, fine root dynamics along the stand productivity gradients were closely linked to stand productivity and were affected by limiting soil properties related to the specific substrate used for reconstructing the reclaimed soil. Understanding the impact of soil properties on fine root dynamics and overall stand productivity will help improve land reclamation outcomes.

Retrospective Analysis of Mosh-Pit-Related Injuries.

Science.gov (United States)

Milsten, Andrew M; Tennyson, Joseph; Weisberg, Stacy

2017-12-01

Moshing is a violent form of dancing found world-wide at rock concerts, festivals, and electronic dance music events. It involves crowd surfing, shoving, and moving in a circular rotation. Moshing is a source of increased morbidity and mortality. The goal of this study was to report epidemiologic information on patient presentation rate (PPR), transport to hospital rate (TTHR), and injury patterns from patients who participated in mosh-pits. Materials and Methods Subjects were patrons from mosh-pits seeking medical care at a single venue. The events reviewed were two national concert tours which visited this venue during their tour. The eight distinct events studied occurred between 2011 and 2014. Data were collected retrospectively from prehospital patient care reports (PCRs). A single Emergency Medical Service (EMS) provided medical care at this venue. The following information was gathered from each PCR: type of injury, location of injury, treatment received, alcohol or drug use, Advanced Life Support/ALS interventions required, age and gender, disposition, minor or parent issues, as well as type of activity engaged in when injured. Attendance for the eight events ranged from 5,100 to 16,000. Total patient presentations ranged from 50 to 206 per event. Patient presentations per ten thousand (PPTT) ranged from 56 to 130. The TTHR per 10,000 ranged from seven to 20. The mean PPTT was 99 (95% CI, 77-122) and the median was 98. The mean TTHR was 16 (95% CI, 12-29) and the median TTHR was 17. Patients presenting from mosh-pits were more frequently male (57.6%; Psurfing was the next most significant, accounting for 20% of presentations. The most common body part injured was the head (64% of injuries). This retrospective review of mosh-pit-associated injury patterns demonstrates a high rate of injuries and presentations for medical aid at the evaluated events. General moshing was the most commonly associated activity and the head was the most common body part injured

200 West Area Ash Pit Demolition Site closure plan. Revision 1

International Nuclear Information System (INIS)

Ruck, F.R.

1994-01-01

The Ash Pit Demolition Site had two known demolition events, the first occurred in November of 1984, and the second occurred in June of 1986. These demolition events were a form of thermal treatment for discarded explosive chemical products. Because the Ash Pit Demolition Site will no longer be used for this thermal activity, the site will be closed. Closure will be conducted pursuant to the requirements of the Washington State Department of Ecology (Ecology) ''Dangerous Waste Regulations'', Washington Administrative Code (WAC) 173-303-610 and 40 Code of Federal Regulations (CFR) 270.1. The 200 West Area Ash Pit Demolition Site Closure Plan consists of a Part A, Form 3, Dangerous Waste Permit Application (Revision 4) and a closure plan. An explanation of the Part A, Form 3, submitted with this closure plan is provided at the beginning of the Part A Section. The closure plan consists of nine chapters and five appendices. This closure plan presents a description of the Ash,Pit Demolition Site, the history of the waste treated, and the approach that will be followed to close the Ash Pit Demolition Site. Because there were no radioactively contaminated chemicals involved in the demolitions, the information on radionuclides is provided for ''information only''. Remediation of any radioactive contamination is not within the scope of this closure plan. Only dangerous constituents derived from Ash Pit Demolition Site operations will be addressed in this closure plan in accordance with WAC 173-303-610(2)(b)(i)

On Pluvial Compaction of Sand

DEFF Research Database (Denmark)

Jacobsen, Moust

At the Institute of Civil Engineering in Aalborg model tests on dry sand specimens have been carried out during the last five years. To reduce deviations in test results, the sand laying technique has been carefully studied, and the sand mass spreader constructed. Preliminary results have been...

MORPHOMETRIC CHARACTERIZATION OF THE SAND FRACTION IN A SAND GRAIN IMAGE CAPTURE SYSTEM1

Directory of Open Access Journals (Sweden)

Lucimar Arruda Viana

Full Text Available ABSTRACT Morphology studies assume significant importance in analysis of phenomena of granular systems packaging, in particular with a view to the use of the technique of soil stabilization named particle size correction in forest roads. In this context, this study aimed to develop and operationalize a Sand Grain Image Capture System and, hereby, determine the morphological indices of the sand fractions of two sandy soils called João Pinheiro (JP and Cachoeira da Prata (CP. Soil samples, air-dried, were sieved (2.0 mm nominal mesh size for removal of gravels. The materials that passed through the sieve were subjected to dispersion, washing in 0.053 mm nominal mesh size sieve, removal of organic matter and iron oxides to obtain the clean sand fractions. Subsequently, each soil sample was sieved for separation into twelve classes, between the diameters of 0.149 mm and 1.190 mm, using a Rotap shaker. Next, tests were carried out to characterize the morphometric attributes of the twelve classes of sand fractions of the soils studied. For validation of the performance of the Sand Grain Image Capture System, the results were compared to those obtained using a standard procedure for image analysis. The analysis of the results led to the following conclusions: (i the sand fraction of the JP soil presented higher values for the morphometric indices roundness, elongation and compactness compared to sand fraction of the CP soil; and (ii the Sand Grain Image Capture System worked properly, with practicality.

Technology unlocks tar sands energy

Energy Technology Data Exchange (ETDEWEB)

Law, C

1967-09-25

Tar sand processing technology has been developed primarily in the categories of extraction techniques and in-situ processing. In October, a $235 million venture into tar sand processing will be inspected by visitors from many points on the globe. A synthetic crude of premium quality will be flowing through a 16-in. pipeline from the Tar Island plant site of Great Canadian Oil Sands to Edmonton. This processing plant uses an extractive mining technique. The tar sand pay zone in this area averages approximately 150 ft in thickness with a 50-ft overburden. It has been estimated that the tar sands cannot be exploited when the formation thickness is less than 100 ft and overburden exceeds the same amount. This indicates that extraction techniques can only be used to recover approximately 15% of the tar sand deposits. An in-situ recovery technique developed by Shell of Canada is discussed in detail. In essence it is selective hydraulic fracturing, followed by the injection of emulsifying chemicals and steam.

The effect of precipitated carbides on the pitting corrosion of 304 stainless steel

International Nuclear Information System (INIS)

Kwak, Jai-Hyun; Kim, Kwan-Hun

1985-01-01

In order to investigate the relation between the pitting corrosion and precipitated carbides, the heat treatment of specimens was carried out in two ways: Solution treatment and carbides precipitation treatment. The experiment was focused on the polarization curves of specimens immersed in HCL solution and on the microscopic analysis of the corroded specimens through a potentiodynamic method. It was found out that the intergranular and pitting corrosion occurred remarkably in 0.1N and 1N KCL solution when carbides were precipitated around the grain boundary of the 304 stain steel. The intergranular corrosion was noticed in the region of passivation and the pitting was prominent in the region of passivation break-down. The distribution of pits on the solution treated 304 stainless steel was random, while that of pits on carbides precipitated specimen was concentrated around the grain boundary in 0.1N and 1N HCL solution. It was ascertained that the pitting resistance of the solution treated 304 stainless steel was better than that of carbides precipitated specimen. (Author)

Structural Design and Monitoring Analysis of Foundation Pit Support in Yiwu Huishang Tiandi

Science.gov (United States)

Zhang, Chunsu

2017-08-01

Huishang Tiandi deep foundation pit in Yiwu is a two-story basement,which is located in the downtown area and adjacent to the city center main traffic trunk. The surrounding environment is too com-plex to slope. The excavation depth is large, the formation is weak and complex, and the groundwater level is high.In order to ensure the safety of the foundation wall and the surrounding environment, the deformation of the foundation pit support is strictly controlled, and the deformation and internal force of the foundation supporting structure and the surrounding building are monitored.The deformation law of the foundation pit is obtained through the analysis of the horizontal displacement, the deformation rate of the supporting struc-ture, the surrounding environment of the foundation pit and the internal force of the anchor cable. The relia-bility and rationality of the design of foundation pit support are verified. It is of reference value for the de-sign and construction of other deep foundation pit engineering in Yiwu area.

Preliminary study of realizability of Karazhyra open pit coal fines briquetting

International Nuclear Information System (INIS)

Deryavko, I.I.; Perepelkin, I.G.; Chuprunov, K.V.

2001-01-01

Main properties of brown coals in Karazhyra open pit upper and lower packs are determined. Characteristics of these coals briquette-ability are evaluated. A conceptual possibility to obtain high-quality briquettes from open pit coal fines is shown. (author)

On the rationality of borrowers' behaviour : Comparing risk-attitudes of homeowners

NARCIS (Netherlands)

Neuteboom, P.

2008-01-01

Though time and depth of cycles differed from one European country to another, mortgage markets have grown in size, expanded in product variation and improved borrowers' accessibility to mortgage credit. However, this expanding range of mortgage opportunities significantly increases the search and

Geotechnical aspects of rock borrow for large breakwaters

International Nuclear Information System (INIS)

Watson, I.; Fischer, J.A.; Urlich, C.M.

1975-01-01

The state of the art is described of investigations to secure rock borrow for the breakwaters proposed to protect offshore nuclear power plants. Considerations relating to the geological, geotechnical, and design suitability of rock are discussed within the framework of economics, and the environmental impact of quarrying and transporting rock to potential sites on the East and Gulf coasts of the U.S. is examined. The methodology outlined has application to the construction of all large rockfill breakwaters

PREVENTION OF ACID MINE DRAINAGE GENERATION FROM OPEN-PIT MINE HIGHWALLS

Science.gov (United States)

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Available information on the generation of AMD from open-pit mine highwalls is very limit...

Neutron transport by TRIPOLI-2 code in the lower part of a PWR pit and in the pit-access cell

International Nuclear Information System (INIS)

Vergnaud, T.; Bourdet, L.; Gonnord, J.; Nimal, J.C.; Champion, G.

1984-09-01

The neutrons, which exit the reactor vessel, leak between the reactor vessel and the primary concrete shield and provide high dose rate in the lower part of the reactor pit. In this part of the reactor the biological shield is reduced at the level of the pit-access cell door and of the ventilation duct. Consequently there is a pin-point increase of dose rate at reactor place where access must be free during power operation. Studies concern 900 MWe and 1300 MWe plants; calculation results are compared with dose rate measurements which have been done at several interesting points of reactor. Neutron transport is studied in two steps: - first Monte Carlo calculation carried out by the TRIPOLI-2 system gives the current of neutrons entering into the pit-access cell; - a second calculation is about neutron transport in this cell; it is also performed with the TRIPOLI-2 code which uses a very realistic model for cell geometry. Then the door efficiency is evaluated by a SN one dimension code

The United States pit disassembly and conversion project -- Meeting the MOX fuel specification

International Nuclear Information System (INIS)

Nelson, T.O.; James, C.A.; Kolman, D.G.

1998-01-01

The US is actively involved in demonstrating the disassembly of nuclear weapons pits to an unclassified form readied for disposition. The MOX option is the most likely path forward for plutonium that originated from nuclear weapon pits. The US demonstration line for pit disassembly and conversion is known as ARIES, the advanced recovery and integrated extraction system. The ARIES demonstration line is being used to gather data in an integrated fashion of the technologies needed for pit disassembly and conversion. These activities include the following modules: pit bisection, hydride-dehydride, oxide conversion, canning, electrolytic decontamination, and nondestructive assay (NDA). Pit bisection swages in a pit in half. Hydride-dehydride converts the pit plutonium metal to an unclassified metal button. To convert the plutonium metal to an oxide the US is investigating a number of options. The primary oxide conversion approach involves variations of combining plutonium hydriding and subsequent oxidation. Another approach is to simply oxidize the metal under controlled conditions-direct metal oxidation (DMO). To remove the gallium from the plutonium oxide, a thermal distillation approach is being used. These pyrochemical approaches will substantially reduce the wastes produced for oxide conversion of weapon plutonium, compared to traditional aqueous processing. The packaging of either the plutonium metal or oxide to long term storage criteria involves the canning and electrolytic decontamination modules. The NDA suite of instruments is then used to assay the material in the containers, which enables international verification without the need to open the containers and repackage them. All of these processes are described

Itataia's deposit - Structural zoning of a pit until the level 480 meters

International Nuclear Information System (INIS)

Mendonca, J.C.G.S.

1986-01-01

This work is part of Itataia Project-Geotechnics; in it are introduced several comments concerning the structural zoning of a pit in Itataias' phosphorous-uranipherous deposit, until the level 480 meters. The structural parameters (fractures, faults, foliations) obtained in surface and underground works were statistically treated. Stereographic projection was used to define eventual slipping into the pit. All the data were arranged in tables to make it easy the comparison with experimental pits. (author) [pt

Bituminous sands : tax issues

International Nuclear Information System (INIS)

Patel, B.

2004-01-01

This paper examined some of the tax issues associated with the production of bitumen or synthetic crude oil from oil sands. The oil sands deposits in Alberta are gaining more attention as the supplies of conventional oil in Canada decline. The oil sands reserves located in the Athabasca, Cold Lake and Peace River areas contain about 2.5 trillion barrels of highly viscous hydrocarbons called bitumen, of which nearly 315 billion barrels are recoverable with current technology. The extraction method varies for each geographic area, and even within zones and reservoirs. The two most common extraction methods are surface mining and in-situ extraction such as cyclic steam stimulation (CSS); low pressure steam flood; pressure cycle steam drive; steam assisted gravity drainage (SAGD); hot water flooding; and, fire flood. This paper also discussed the following general tax issues: bituminous sands definition; bituminous sands leases and Canadian development expense versus Canadian oil and gas property expense (COGPE); Canadian exploration expense (CEE) for surface mining versus in-situ methods; additional capital cost allowance; and, scientific research and experimental development (SR and ED). 15 refs

Oil sands tax expenditures

International Nuclear Information System (INIS)

Ketchum, K; Lavigne, R.; Plummer, R.

2001-01-01

The oil sands are a strategic Canadian resource for which federal and provincial governments provide financial incentives to develop and exploit. This report describes the Oil Sands Tax Expenditure Model (OSTEM) developed to estimate the size of the federal income tax expenditure attributed to the oil sands industry. Tax expenditures are tax concessions which are used as alternatives to direct government spending for achieving government policy objectives. The OSTEM was developed within the business Income Tax Division of Canada's Department of Finance. Data inputs for the model were obtained from oil sands developers and Natural Resources Canada. OSTEM calculates annual revenues, royalties and federal taxes at project levels using project-level projections of capital investment, operating expenses and production. OSTEM calculates tax expenditures by comparing taxes paid under different tax regimes. The model also estimates the foregone revenue as a percentage of capital investment. Total tax expenditures associated with investment in the oil sands are projected to total $820 million for the period from 1986 to 2030, representing 4.6 per cent of the total investment. 10 refs., 2 tabs., 7 figs

25 CFR 103.36 - What options and remedies does the lender have if the borrower defaults on the loan?

Science.gov (United States)

2010-04-01

... result in the borrower curing the default. (b) The lender may make precautionary advances on the borrower... prospects do not significantly deteriorate. Items for which the lender may make precautionary advances include, for example: (1) Hazard, liability, or key man life insurance premiums; (2) Security measures to...

Revegetation and soil development on anthropogenic disturbances in shrub tundra, 50 years following construction of the CANOL No. 1 pipeline, N.W.T

International Nuclear Information System (INIS)

Harper, K.A.

1994-01-01

An intensive study of long-term revegetation patterns of erect deciduous shrub tundra on anthropogenic disturbances was conducted in the summer of 1993 within the CANOL pipeline corridor, Northwest Territories. Soil development, primary and secondary succession were investigated on 10 m by 20 m sites in vehicle tracks and borrow pits. Data were collected on the cover of all vascular and non-vascular species. Soil temperature, pH, organic matter, moisture and particle size composition were determined. Patterns in plant species composition and soil characteristics among disturbance types were examined using detrended correspondence analysis. The importance of the measured abiotic factors in explaining the differences in species composition was revealed by canonical correspondence analysis. Significant differences in species composition were evident among disturbance types. Different taxonomic groups exhibited different responses to disturbance. Soil samples in linear disturbances were analogous to those in undisturbed areas. Warmer, drier and less acidic soils in borrow pits contained less organic matter and fine particles than undisturbed soils. Soil temperature was considered the most important measured environmental variable in accounting for the revegetation patterns on disturbance with the microclimate stations. Comparison with a similar study on revegetation in the CANOL corridor in 1978 suggest that revegetation and soil development are proceeding faster on linear disturbances than borrow pits. 150 figs., 37 figs., 28 tabs

Bitter pit in apples: pre- and postharvest factors: A review

International Nuclear Information System (INIS)

Jemrić, T.; Fruk, I.; Fruk, M.; Radman, S.; Sinkovič, L.; Fruk, G.

2016-01-01

Bitter pit is a physiological disorder that significantly reduces the quality of apples. Although it has been detected since the beginning of the last century, still there is little known about the mechanism of its occurrence. According to numerous studies, bitter pit is formed as a result of calcium deficiency in the fruit. Some authors cite the high concentration of gibberellins, later in the production season, most probably caused by excessive activity of the roots, as the chief causative factor. Beside Ca, there are several factors that can also contribute to its development, like imbalance among some mineral elements (N, P, K and Mg), cultivar, rootstock, the ratio of vegetative and generative growth, post-harvest treatments and the storage methods. There are some prediction models available that can estimate the risk of bitter pit in apples, but even those are not always reliable. The aim of this review was to encompass the pre and postharvest factors which cause bitter pit and point out the directions for solving this problem.

Bitter pit in apples: pre- and postharvest factors: A review

Energy Technology Data Exchange (ETDEWEB)

Jemrić, T.; Fruk, I.; Fruk, M.; Radman, S.; Sinkovič, L.; Fruk, G.

2016-07-01

Bitter pit is a physiological disorder that significantly reduces the quality of apples. Although it has been detected since the beginning of the last century, still there is little known about the mechanism of its occurrence. According to numerous studies, bitter pit is formed as a result of calcium deficiency in the fruit. Some authors cite the high concentration of gibberellins, later in the production season, most probably caused by excessive activity of the roots, as the chief causative factor. Beside Ca, there are several factors that can also contribute to its development, like imbalance among some mineral elements (N, P, K and Mg), cultivar, rootstock, the ratio of vegetative and generative growth, post-harvest treatments and the storage methods. There are some prediction models available that can estimate the risk of bitter pit in apples, but even those are not always reliable. The aim of this review was to encompass the pre and postharvest factors which cause bitter pit and point out the directions for solving this problem.

Singing Sand Dunes

Indian Academy of Sciences (India)

ble low-frequency (s. 75–105 Hz), that can some- times be heard up to 10 km away. Scientific in- vestigations suggest that the sustained low fre- quency sound of sand dunes that resembles a pure note from a musical instrument, is due to the synchronized motion of well-sorted dry sand grains when they spontaneously ...

Evaluating the Metal Tolerance Capacity of Microbial Communities Isolated from Alberta Oil Sands Process Water.

Directory of Open Access Journals (Sweden)

Mathew L Frankel

Full Text Available Anthropogenic activities have resulted in the intensified use of water resources. For example, open pit bitumen extraction by Canada's oil sands operations uses an estimated volume of three barrels of water for every barrel of oil produced. The waste tailings-oil sands process water (OSPW-are stored in holding ponds, and present an environmental concern as they are comprised of residual hydrocarbons and metals. Following the hypothesis that endogenous OSPW microbial communities have an enhanced tolerance to heavy metals, we tested the capacity of planktonic and biofilm populations from OSPW to withstand metal ion challenges, using Cupriavidus metallidurans, a known metal-resistant organism, for comparison. The toxicity of the metals toward biofilm and planktonic bacterial populations was determined by measuring the minimum biofilm inhibitory concentrations (MBICs and planktonic minimum inhibitory concentrations (MICs using the MBEC ™ assay. We observed that the OSPW community and C. metallidurans had similar tolerances to 22 different metals. While thiophillic elements (Te, Ag, Cd, Ni were found to be most toxic, the OSPW consortia demonstrated higher tolerance to metals reported in tailings ponds (Al, Fe, Mo, Pb. Metal toxicity correlated with a number of physicochemical characteristics of the metals. Parameters reflecting metal-ligand affinities showed fewer and weaker correlations for the community compared to C. metallidurans, suggesting that the OSPW consortia may have developed tolerance mechanisms toward metals present in their environment.

DEFINICIÓN DE PIT FINAL CAPACITADO BAJO INCERTIDUMBRE

OpenAIRE

PEIRANO OPAZO, FERNANDO ANDRÉS

2011-01-01

El objetivo principal de este trabajo de tesis es desarrollar una metodología y una herramienta que permitan definir un pit final incorporando las restricciones de capacidad y las condiciones de incertidumbre asociadas al recurso geológico. El resultado metodológico consiste en un algoritmo de cálculo que incorpora heurísticas de definición de pit final como es la enunciada por Lerchs y Grossman (1964), en conjunto con heurísticas de secuenciamiento de bloques como son enunciadas por Gersh...

Optimal grade control sampling practice in open-pit mining

DEFF Research Database (Denmark)

Engström, Karin; Esbensen, Kim Harry

2017-01-01

Misclassification of ore grades results in lost revenues, and the need for representative sampling procedures in open pit mining is increasingly important in all mining industries. This study evaluated possible improvements in sampling representativity with the use of Reverse Circulation (RC) drill...... sampling compared to manual Blast Hole (BH) sampling in the Leveäniemi open pit mine, northern Sweden. The variographic experiment results showed that sampling variability was lower for RC than for BH sampling. However, the total costs for RC drill sampling are significantly exceeding current costs...... for manual BH sampling, which needs to be compensated for by other benefits to motivate introduction of RC drilling. The main conclusion is that manual BH sampling can be fit-for-purpose in the studied open pit mine. However, with so many mineral commodities and mining methods in use globally...

7 CFR 1780.47 - Borrower accounting methods, management reporting and audits.

Science.gov (United States)

2010-01-01

... accrual basis of accounting, in accordance with generally accepted accounting principles (GAAP), unless... organization may maintain its accounting records on a basis other than accrual accounting, and make the... 7 Agriculture 12 2010-01-01 2010-01-01 false Borrower accounting methods, management reporting and...

24 CFR 201.42 - Bankruptcy, insolvency or death of borrower.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Bankruptcy, insolvency or death of..., insolvency or death of borrower. (a) Bankruptcy or insolvency. The lender shall file a proof of claim with... bankruptcy or insolvency proceedings, except that a proof of claim need not be filed if the court notifies...

Modelling the filling rate of pit latrines | Brouckaert | Water SA

African Journals Online (AJOL)

Excreta (faeces and urine) that are deposited into a pit latrine are subject to biodegradation, which substantially reduces the volume that remains. On the other hand, other matter that is not biodegradable usually finds itsway into pit latrines. The net filling rate is thus dependent on both the rate of addition of material and its ...

241-AY-102 Leak Detection Pit Drain Line Inspection Report

International Nuclear Information System (INIS)

Boomer, Kayle D.; Engeman, Jason K.; Gunter, Jason R.; Joslyn, Cameron C.; Vazquez, Brandon J.; Venetz, Theodore J.; Garfield, John S.

2014-01-01

This document provides a description of the design components, operational approach, and results from the Tank AY-102 leak detection pit drain piping visual inspection. To perform this inspection a custom robotic crawler with a deployment device was designed, built, and operated by IHI Southwest Technologies, Inc. for WRPS to inspect the 6-inch leak detection pit drain line

75 FR 38501 - The Release of the Final Environmental Impact Statement (FEIS) for the Town of Nags Head Proposed...

Science.gov (United States)

2010-07-02

... cubic yards of beach-quality sediment from an offshore borrow source, and deposit the material along... dredging operations and discharge the sand on the beach via submerged pipeline. The applicant's proposed borrow areas include sites identified as having beach quality material in the U.S. Army Corps of...

Criticality safety evaluation report for the 100 KE Basin sandfilter backwash pit

International Nuclear Information System (INIS)

Erickson, D.G.

1995-01-01

This analysis presents the technical basis for establishing a safe mass limit for continued operations of the KE Basin sandfilter backwash pit. The main analysis is based on a very conservative UO 2 -PuO 2 -H 2 O system using the measured isotopic concentrations of uranium and plutonium in the sludge. Appendix C contains analyses of the sandfilter backwash pit utilizing all verified materials presently in the pit, and gives new limits based on assumptions made

New diagnostic technology and hidden pits and fissures caries

OpenAIRE

Fabrizio Guerra; Marta Mazur; Francesca Rinaldo; Denise Corridore; Daniele Salvi; Debora Pasqualotto; Gianna Maria Nardi; Livia Ottolenghi

2015-01-01

The accuracy in pits and fissures caries detection is of paramount importance in dental caries primary and secondary prevention. A combination of visual examination and probing is currently the mainstay of occlusal caries diagnosis. Unfortunately, these types of inspection alone may leave a certain number of pit and fissure caries undetected. The Vista Cam iX fluorescence camera (Durr Dental, Bietigheim-Bissingen, Germany) is a novel dental diagnostic tool for quantitative assessment of denta...

78 FR 33894 - Proposed Information Collection (Open Burn Pit Registry Airborne Hazard Self-Assessment...

Science.gov (United States)

2013-06-05

... chemicals and fumes caused by open burn pits. DATES: Written comments and recommendations on the proposed... to ``OMB Control No. 2900-NEW, Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire.... Title: Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire, VA Form 10-10066. OMB...

Lessons Learned from Pit Viper Integration into Hanford Tank Farm Reality

International Nuclear Information System (INIS)

Catalan, Michael A.; Bailey, Sharon A.; Alzheimer, James M.; Niebuhr, Daniel P.

2002-01-01

The Pit Viper is a tele-operated system intended to enhance worker safety while simultaneously improving the efficiency of pit operations at the Hanford Site. Commercial off-the-shelf (COTS) components were used in an attempt to increase system efficiency. During preparation for initial deployment, the Pit Viper team identified multiple areas where more advanced technology offers substantial improvement in system capabilities. The team also ensured that the system as is, was capable of fulfilling its mission. However, there are valid concerns of the reliability of the technology. Areas where improvement are desired include; operator feedback, manipulator dexterous envelope, and system reliability

Designing local solutions for emptying pit latrines in low-income urban settlements (Malawi)

Science.gov (United States)

Chipeta, W. C.; Holm, R. H.; Kamanula, J. F.; Mtonga, W. E.; de los Reyes, F. L.

2017-08-01

A lack of effective options in local technology poses challenges when onsite household sanitation facilities are eventually filled to capacity in unplanned settlement areas within Mzuzu City, located in northern Malawi. Vacuum trucks currently dominate the market but focus on emptying septic tanks in the more easily accessible planned settlement areas, rather than servicing the pit latrines common in unplanned settlement areas. As a result, households in the unplanned settlement areas within Mzuzu rely primarily on manual pit emptying (i.e., shoveling by hand) or digging a new pit latrine. These practices have associated health risks and are limited by space constraints. This research focused on filling the technological gap through the design, development, and testing of a pedal powered modified Gulper pump using locally available materials and fabrication. A modified pedal powered Gulper technology was developed and demonstrated to be capable of lifting fecal sludge from a depth of 1.5 m with a mean flow rate of 0.00058 m3/s. If the trash content was low, a typical pit latrine with a volume of 1-4 m3 could be emptied within 1-2 h. Based on the findings in our research Phase IV, the pedal powered Gulper modification is promising as a potential emptying technology for lined pit latrines in unplanned settlement areas. The success rate of the technology is about 17% (5 out 30 sampled lined pit latrines were successful) and reflects the difficulty in finding a single technology that can work well in all types of pit latrines with varying contents. We note that cost should not be the only design criteria and acknowledge the challenge of handling trash in pit latrines.

Probability distribution of pitting corrosion depth and rate in underground pipelines: A Monte Carlo study

International Nuclear Information System (INIS)

Caleyo, F.; Velazquez, J.C.; Valor, A.; Hallen, J.M.

2009-01-01

The probability distributions of external-corrosion pit depth and pit growth rate were investigated in underground pipelines using Monte Carlo simulations. The study combines a predictive pit growth model developed by the authors with the observed distributions of the model variables in a range of soils. Depending on the pipeline age, any of the three maximal extreme value distributions, i.e. Weibull, Frechet or Gumbel, can arise as the best fit to the pitting depth and rate data. The Frechet distribution best fits the corrosion data for long exposure periods. This can be explained by considering the long-term stabilization of the diffusion-controlled pit growth. The findings of the study provide reliability analysts with accurate information regarding the stochastic characteristics of the pitting damage in underground pipelines.

Probability distribution of pitting corrosion depth and rate in underground pipelines: A Monte Carlo study

Energy Technology Data Exchange (ETDEWEB)

Caleyo, F. [Departamento de Ingenieria Metalurgica, ESIQIE, IPN, UPALM Edif. 7, Zacatenco, 07738 Mexico, D.F. (Mexico)], E-mail: fcaleyo@gmail.com; Velazquez, J.C. [Departamento de Ingenieria Metalurgica, ESIQIE, IPN, UPALM Edif. 7, Zacatenco, 07738 Mexico, D.F. (Mexico); Valor, A. [Facultad de Fisica, Universidad de La Habana, San Lazaro y L, Vedado, 10400, La Habana (Cuba); Hallen, J.M. [Departamento de Ingenieria Metalurgica, ESIQIE, IPN, UPALM Edif. 7, Zacatenco, 07738 Mexico, D.F. (Mexico)

2009-09-15

The probability distributions of external-corrosion pit depth and pit growth rate were investigated in underground pipelines using Monte Carlo simulations. The study combines a predictive pit growth model developed by the authors with the observed distributions of the model variables in a range of soils. Depending on the pipeline age, any of the three maximal extreme value distributions, i.e. Weibull, Frechet or Gumbel, can arise as the best fit to the pitting depth and rate data. The Frechet distribution best fits the corrosion data for long exposure periods. This can be explained by considering the long-term stabilization of the diffusion-controlled pit growth. The findings of the study provide reliability analysts with accurate information regarding the stochastic characteristics of the pitting damage in underground pipelines.

3D Modeling of Lacus Mortis Pit Crater with Presumed Interior Tube Structure

Directory of Open Access Journals (Sweden)

Ik-Seon Hong

2015-06-01

Full Text Available When humans explore the Moon, lunar caves will be an ideal base to provide a shelter from the hazards of radiation, meteorite impact, and extreme diurnal temperature differences. In order to ascertain the existence of caves on the Moon, it is best to visit the Moon in person. The Google Lunar X Prize(GLXP competition started recently to attempt lunar exploration missions. Ones of those groups competing, plan to land on a pit of Lacus Mortis and determine the existence of a cave inside this pit. In this pit, there is a ramp from the entrance down to the inside of the pit, which enables a rover to approach the inner region of the pit. In this study, under the assumption of the existence of a cave in this pit, a 3D model was developed based on the optical image data. Since this model simulates the actual terrain, the rendering of the model agrees well with the image data. Furthermore, the 3D printing of this model will enable more rigorous investigations and also could be used to publicize lunar exploration missions with ease.

3D Modeling of Lacus Mortis Pit Crater with Presumed Interior Tube Structure

Science.gov (United States)

Hong, Ik-Seon; Yi, Yu; Yu, Jaehyung; Haruyama, Junichi

2015-06-01

When humans explore the Moon, lunar caves will be an ideal base to provide a shelter from the hazards of radiation, meteorite impact, and extreme diurnal temperature differences. In order to ascertain the existence of caves on the Moon, it is best to visit the Moon in person. The Google Lunar X Prize(GLXP) competition started recently to attempt lunar exploration missions. Ones of those groups competing, plan to land on a pit of Lacus Mortis and determine the existence of a cave inside this pit. In this pit, there is a ramp from the entrance down to the inside of the pit, which enables a rover to approach the inner region of the pit. In this study, under the assumption of the existence of a cave in this pit, a 3D model was developed based on the optical image data. Since this model simulates the actual terrain, the rendering of the model agrees well with the image data. Furthermore, the 3D printing of this model will enable more rigorous investigations and also could be used to publicize lunar exploration missions with ease.

Pit morphology studies of iron and steel in alkaline chloride environment using EMPA technique

International Nuclear Information System (INIS)

Benjamin, S.E.; Sykes, J.M.

1993-01-01

A comparative study of iron and steel in stimulated alkaline chloride solutions showed that Swedish iron has better reproducibility in terms of pitting potentials as compared to ordinary hot rolled mild steel. This study was undertaken to reason this pitting behavior on the basis of number and the nature of inclusions present in both the metals. Electron probe microanalysis technique (EPMA) was utilised to contemplate the origin of pits, the solution chemistry of the pits and finally the nature of the rust product. (author)

Enhanced characterization of oil sands acid-extractable organics fractions using electrospray ionization-high-resolution mass spectrometry and synchronous fluorescence spectroscopy.

Science.gov (United States)

Bauer, Anthony E; Frank, Richard A; Headley, John V; Peru, Kerry M; Hewitt, L Mark; Dixon, D George

2015-05-01

The open pit oil sands mining operations north of Fort McMurray, Alberta, Canada, are accumulating tailings waste at a rate approximately equal to 4.9 million m(3) /d. Naphthenic acids are among the most toxic components within tailings to aquatic life, but structural components have largely remained unidentified. In the present study, electrospray ionization high-resolution mass spectrometry (ESI-HRMS) and synchronous fluorescence spectroscopy (SFS) were used to characterize fractions derived from the distillation of an acid-extractable organics (AEO) mixture isolated from oil sands process-affected water (OSPW). Mean molecular weights of each fraction, and their relative proportions to the whole AEO extract, were as follows: fraction 1: 237 Da, 8.3%; fraction 2: 240 Da, 23.8%; fraction 3: 257 Da, 26.7%; fraction 4: 308 Da, 18.9%; fraction 5: 355 Da, 10.0%. With increasing mean molecular weight of the AEO fractions, a concurrent increase occurred in the relative abundance of nitrogen-, sulfur-, and oxygen-containing ions, double-bond equivalents, and degree of aromaticity. Structures present in the higher-molecular-weight fractions (fraction 4 and fraction 5) suggested the presence of heteroatoms, dicarboxyl and dihydroxy groups, and organic acid compounds with the potential to function as estrogens. Because organic acid compositions become dominated by more recalcitrant, higher-molecular-weight acids during natural degradation, these findings are important in the context of oil sands tailings pond water remediation. © 2015 SETAC.

Atypical pit craters on Mars: new insights from THEMIS, CTX and HiRISE observations

Science.gov (United States)

Cushing, Glen; Okubo, Chris H.; Titus, Timothy N.

2015-01-01

More than 100 pit craters in the Tharsis region of Mars exhibit morphologies, diameters and thermal behaviors that diverge from the much larger bowl-shaped pit craters that occur in most regions across Mars. These Atypical Pit Craters (APCs) generally have sharp and distinct rims, vertical or overhanging walls that extend down to their floors, surface diameters of ~50-350 m, and high depth-to-diameter (d/D) ratios that are usually greater than 0.3 (which is an upper-range value for impacts and bowl-shaped pit craters), and can exceed values of 1.8. Observations by the Mars Odyssey THermal Emission Imaging System (THEMIS) show that APC floor temperatures are warmer at night, and fluctuate with much lower diurnal amplitudes than nearby surfaces or adjacent bowl-shaped pit craters. Kīlauea volcano, Hawai'i, hosts pit craters that formed through subsurface collapse into active volcanic dikes, resulting in pits that can appear morphologically analogous to either APCs or bowl-shaped pit craters. Partially-drained dikes are sometimes exposed within the lower walls and floors of these terrestrial APC analogs and can form extensive cave systems with unique microclimates. Similar caves in martian pit craters are of great interest for astrobiology. This study uses new observations by the Mars Reconnaissance Orbiter (MRO) High Resolution Imaging Science Experiment (HiRISE) and Context Camera (CTX) to refine previous work where seven APCs were described from lower-resolution THEMIS visible-wavelength (VIS) observations. Here, we identify locations of 115 APCs, map their distribution across the Tharsis region, characterize their internal morphologies with high-resolution observations, and discuss possible formation mechanisms.

7 CFR 1710.102 - Borrower eligibility for different types of loans.

Science.gov (United States)

2010-01-01

... LOANS AND GUARANTEES Loan Purposes and Basic Policies § 1710.102 Borrower eligibility for different... grid renewable energy systems. (See 7 CFR part 1712). These guarantees are normally used to finance bulk transmission and generation facilities, but they may also be used to finance distribution and...

A New Algorithm for Determining Ultimate Pit Limits Based on Network Optimization

OpenAIRE

Ali Asghar Khodayari

2013-01-01

One of the main concerns of the mining industry is to determine ultimate pit limits. Final pit is a collection of blocks, which can be removed with maximum profit while following restrictions on the slope of the mine’s walls. The size, location and final shape of an open-pit are very important in designing the location of waste dumps, stockpiles, processing plants, access roads and other surface facilities as well as in developing a production program. There are numerous methods for designing...

Pitting growth modelling in buried oil and gas pipelines using statistical techniques

International Nuclear Information System (INIS)

Velazquez, J. C.; Caleyo, F.; Valorm, A.; Hallen, J. M.

2011-01-01

New deterministic and stochastic predictive models are proposed for external pitting corrosion in underground pipelines. The deterministic model takes into consideration the local chemical and physical properties of the soil as well as the pipeline coating to predict the time dependence of pitting depth and rate in a range of soils. This model, based on results from a field study, was used to conduct Monte Carlo simulations that established the probability distribution of pitting depth and growth rate in the studied soils and their evolution over the life of the pipeline. In the last stage of the study, an empirical Markov chain-based stochastic model was developed for predicting the evolution of pitting corrosion depth and rate distributions from the observed properties of the soil. (Author) 18 refs.

A Time to Every Purpose: Understanding and Improving the Borrower Experience with Online Student Loan Entrance Counseling. Research Report

Science.gov (United States)

Fernandez, Chris

2015-01-01

Legally mandated student loan entrance counseling attempts to prepare first-time borrowers of federal student loans for this challenge; yet, researchers hypothesized that the online modules most borrowers use for this purpose have significant shortcomings. This report (the third in a series of five from TG Research) describes a study in which…

Fukushima Nuclear Accident Recorded in Tibetan Plateau Snow Pits

Science.gov (United States)

Wang, Ninglian; Wu, Xiaobo; Kehrwald, Natalie; Li, Zhen; Li, Quanlian; Jiang, Xi; Pu, Jianchen

2015-01-01

The β radioactivity of snow-pit samples collected in the spring of 2011 on four Tibetan Plateau glaciers demonstrate a remarkable peak in each snow pit profile, with peaks about ten to tens of times higher than background levels. The timing of these peaks suggests that the high radioactivity resulted from the Fukushima nuclear accident that occurred on March 11, 2011 in eastern Japan. Fallout monitoring studies demonstrate that this radioactive material was transported by the westerlies across the middle latitudes of the Northern Hemisphere. The depth of the peak β radioactivity in each snow pit compared with observational precipitation records, suggests that the radioactive fallout reached the Tibetan Plateau and was deposited on glacier surfaces in late March 2011, or approximately 20 days after the nuclear accident. The radioactive fallout existed in the atmosphere over the Tibetan Plateau for about one month. PMID:25658094

Standardized emissions inventory methodology for open-pit mining areas.

Science.gov (United States)

Huertas, Jose I; Camacho, Dumar A; Huertas, Maria E

2011-08-01

There is still interest in a unified methodology to quantify the mass of particulate material emitted into the atmosphere by activities inherent to open-pit mining. For the case of total suspended particles (TSP), the current practice is to estimate such emissions by developing inventories based on the emission factors recommended by the USEPA for this purpose. However, there are disputes over the specific emission factors that must be used for each activity and the applicability of such factors to cases quite different to the ones under which they were obtained. There is also a need for particulate matter with an aerodynamic diameter less than 10 μm (PM(10)) emission inventories and for metrics to evaluate the emission control programs implemented by open-pit mines. To address these needs, work was carried out to establish a standardized TSP and PM(10) emission inventory methodology for open-pit mining areas. The proposed methodology was applied to seven of the eight mining companies operating in the northern part of Colombia, home to the one of the world's largest open-pit coal mining operations (∼70 Mt/year). The results obtained show that transport on unpaved roads is the mining activity that generates most of the emissions and that the total emissions may be reduced up to 72% by spraying water on the unpaved roads. Performance metrics were defined for the emission control programs implemented by mining companies. It was found that coal open-pit mines are emitting 0.726 and 0.180 kg of TSP and PM(10), respectively, per ton of coal produced. It was also found that these mines are using on average 1.148 m(2) of land per ton of coal produced per year.

EXTERNAL BORROWING – A SOLUTION IN OVERCOMING THE CURRENT ECONOMIC CRISIS?

Directory of Open Access Journals (Sweden)

Maria Pascal (căs. Andriescu

2010-06-01

Full Text Available The government decisions to call, in recent years, more and more reimbursable financing gave birth to fierce reactions among politicians and economy specialists. The present article aims to analyze how the external borrowing may be a solution to overcome the difficult situation where we are.

Influence of cracks and pitting corrosion on residual ultimate strength of stiffened plates

Directory of Open Access Journals (Sweden)

ZHANG Jing

2018-02-01

Full Text Available [Objectives] Ships and offshore platforms serve in the harsh sea environment for a long time. Cracks and pitting corrosion will occur in such a structure and the damage will affect its ultimate strength.[Methods] To investigate the influence of cracks and pitting corrosion on ultimate bearing capacity, the ultimate strength of a structure under axial compression is studied by using a nonlinear finite element. The mesh size of a stiffened plate with cracks and pitting corrosion is first discussed. Then the influence of the relative positions of cracks and pitting corrosion, number of corrosion points and crack length impact on the residual ultimate strength of damaged stiffened plates is discussed via a series of calculations.[Results] The results indicate that the increase in crack length and pitting corrosion significantly decreases the ultimate strength of a stiffened plate. [Conclusions] This provides a useful reference for designing and maintaining ships and offshore structures in their life cycles.

Morphological Evolution of Pit-Patterned Si(001) Substrates Driven by Surface-Energy Reduction

Science.gov (United States)

Salvalaglio, Marco; Backofen, Rainer; Voigt, Axel; Montalenti, Francesco

2017-09-01

Lateral ordering of heteroepitaxial islands can be conveniently achieved by suitable pit-patterning of the substrate prior to deposition. Controlling shape, orientation, and size of the pits is not trivial as, being metastable, they can significantly evolve during deposition/annealing. In this paper, we exploit a continuum model to explore the typical metastable pit morphologies that can be expected on Si(001), depending on the initial depth/shape. Evolution is predicted using a surface-diffusion model, formulated in a phase-field framework, and tackling surface-energy anisotropy. Results are shown to nicely reproduce typical metastable shapes reported in the literature. Moreover, long time scale evolutions of pit profiles with different depths are found to follow a similar kinetic pathway. The model is also exploited to treat the case of heteroepitaxial growth involving two materials characterized by different facets in their equilibrium Wulff's shape. This can lead to significant changes in morphologies, such as a rotation of the pit during deposition as evidenced in Ge/Si experiments.

Research on horizontal displacement monitoring method of deep foundation pit based on laser projecting sensing technology

Science.gov (United States)

Liu, Peng; Xie, Shulin; Zhang, Lixiao; Zhou, Guangyi; Zhao, Xuefeng

2018-03-01

A certain level of horizontal displacement will occur during excavation or subsequent construction of deep foundation pit. If the support is improper and the horizontal displacement of the foundation pit is too large, it will cause collapse and even affect the buildings around the foundation pit, which will endanger people's life and property. Therefore, the horizontal displacement monitoring of deep foundation pit becomes more and more important. At present, the electronic total station is often used to monitor the horizontal displacement of the foundation pit, but this monitoring method is expensive, prone to accidental errors, and can not be used for real-time monitoring. Therefore, a method of monitoring the horizontal displacement of deep foundation pit by using laser projection sensing technique is proposed in this paper. The horizontal displacement of the foundation pit is replaced by the displacement of the laser spot emitted by the laser, and the horizontal displacement of the foundation pit can be obtained by identifying the displacement of the laser spot projected on the screen. A series of experiments show that the accuracy of this monitoring method meets the engineering requirements and greatly reduces the cost, which provides a new technology for the displacement monitoring of deep foundation pit.

Experimental and theoretic investigations of thermal behavior of a seasonal water pit heat storage

DEFF Research Database (Denmark)

Fan, Jianhua; Huang, Junpeng; Chatzidiakos, Angelos

Seasonal heat storages are considered essential for district heating systems because they offer flexibility for the system to integrate different fluctuating renewable energy sources. Water pit thermal storages (PTES) have been successfully implemented in solar district heating plants in Denmark....... Thermal behavior of a 75,000 m3 water pit heat storage in Marstal solar heating plant was investigated experimentally and numerically. Temperatures at different levels of the water pit storage and temperatures at different depths of the ground around the storage were monitored and analyzed. A simulation...... model of the water pit storage is built to investigate development of temperatures in and around the storage. The calculated temperatures are compared to the monitored temperatures with an aim to validate the simulation model. Thermal stratification in the water pit heat storage and its interaction...

Impacts of swine manure pits on groundwater quality

International Nuclear Information System (INIS)

Krapac, I.G.; Dey, W.S.; Roy, W.R.; Smyth, C.A.; Storment, E.; Sargent, S.L.; Steele, J.D.

2002-01-01

New information is presented on impacts on groundwater by manure storage in deep ground pits. - Manure deep-pits are commonly used to store manure at confined animal feeding operations. However, previous to this study little information had been collected on the impacts of deep-pits on groundwater quality to provide science-based guidance in formulating regulations and waste management strategies that address risks to human health and the environment. Groundwater quality has been monitored since January 1999 at two hog finishing facilities in Illinois that use deep-pit systems for manure storage. Groundwater samples were collected on a monthly basis and analyzed for inorganic and bacteriological constituent concentrations. The two sites are located in areas with geologic environments representing different vulnerabilities for local groundwater contamination. One site is underlain by more than 6 m of clayey silt, and 7-36 m of shale. Concentrations of chloride, ammonium, phosphate, and potassium indicated that local groundwater quality had not been significantly impacted by pit leakage from this facility. Nitrate concentrations were elevated near the pit, often exceeding the 10 mg N/l drinking water standard. Isotopic nitrate signatures suggested that the nitrate was likely derived from soil organic matter and fertilizer applied to adjacent crop fields. At the other site, sandstone is located 4.6-6.1 m below land surface. Chloride concentrations and δ 15 N and δ 18 O values of dissolved nitrate indicated that this facility may have limited and localized impacts on groundwater. Other constituents, including ammonia, potassium, phosphate, and sodium were generally at or less than background concentrations. Trace- and heavy-metal concentrations in groundwater samples collected from both facilities were at concentrations less than drinking water standards. The concentration of inorganic constituents in the groundwater would not likely impact human health. Fecal

Impacts of swine manure pits on groundwater quality

Energy Technology Data Exchange (ETDEWEB)

Krapac, I.G.; Dey, W.S.; Roy, W.R.; Smyth, C.A.; Storment, E.; Sargent, S.L.; Steele, J.D

2002-12-01

New information is presented on impacts on groundwater by manure storage in deep ground pits. - Manure deep-pits are commonly used to store manure at confined animal feeding operations. However, previous to this study little information had been collected on the impacts of deep-pits on groundwater quality to provide science-based guidance in formulating regulations and waste management strategies that address risks to human health and the environment. Groundwater quality has been monitored since January 1999 at two hog finishing facilities in Illinois that use deep-pit systems for manure storage. Groundwater samples were collected on a monthly basis and analyzed for inorganic and bacteriological constituent concentrations. The two sites are located in areas with geologic environments representing different vulnerabilities for local groundwater contamination. One site is underlain by more than 6 m of clayey silt, and 7-36 m of shale. Concentrations of chloride, ammonium, phosphate, and potassium indicated that local groundwater quality had not been significantly impacted by pit leakage from this facility. Nitrate concentrations were elevated near the pit, often exceeding the 10 mg N/l drinking water standard. Isotopic nitrate signatures suggested that the nitrate was likely derived from soil organic matter and fertilizer applied to adjacent crop fields. At the other site, sandstone is located 4.6-6.1 m below land surface. Chloride concentrations and {delta}{sup 15}N and {delta}{sup 18}O values of dissolved nitrate indicated that this facility may have limited and localized impacts on groundwater. Other constituents, including ammonia, potassium, phosphate, and sodium were generally at or less than background concentrations. Trace- and heavy-metal concentrations in groundwater samples collected from both facilities were at concentrations less than drinking water standards. The concentration of inorganic constituents in the groundwater would not likely impact human

Microstructure and pitting corrosion of 13CrNiMo weld metals

International Nuclear Information System (INIS)

Bilmes, P.D.; Llorente, C.L.; Saire Huaman, L.; Gassa, L.M.; Gervasi, C.A.

2006-01-01

Cyclic potentiodynamic measurements and scanning electron microscopy were used to analyze susceptibility to pitting corrosion of 13CrNiMo weld metals. In order to carry out a critical assessment of the influence of microstructural factors on localized corrosion, different heat treatments were applied to the alloys under investigation. Volume fractions of austenite in tempered conditions as well as the amount and size of precipitated carbides strongly affect pitting resistance. Characteristic potentials (pitting potential and repassivation potential) increase according to the retained austenite content. Results can be discussed in terms of a model that describes the structural refinement resulting from a double-tempering procedure

Effect of heat treatment on pitting corrosion of austenitic Cr-Ni-Mo steels in sodium chloride solution

International Nuclear Information System (INIS)

Stefec, R.; Franz, F.; Holecek, A.

1979-01-01

The pitting corrosion resistance of Cr17Ni12Mo2,5 type steel under potentiostatic polarization in a sodium chloride solution is adversely affected by previous annealing. The data obtained were systematically dependent on annealing temperature, time and surface roughness. The corrosion current, the number of pits or the mean area of pit opening and the corrosion rate within the pits were increased by previous annealing at 550 to 750 0 C for 1-100 hrs. The highest corrosion rate estimated corresponded to heat treatments provoking severe sensitization to intergranular corrosion. The paercentage area of corrosion pit openings and the estimated pit penetration rates were several times higher for as-machined than for polished surfaces. It can be assumed that pitting corrosion is little affected by the carbon content and that molybdenum depletion of grain-boundary zones is responsible for the reduced pitting resistance of annealed steels. (orig./HP) [de

Decontamination and decommissioning of the SPERT-I seepage pit at the Idaho National Engineering Laboratory. Final report

International Nuclear Information System (INIS)

Suckel, R.A.

1984-11-01

This report describes the decontamination and decommissioning of the SPERT-I seepage pit. Prior to its decontamination and decommissioning, the seepage pit was surrounded by an earthen dike varying from 2 to 6 ft above the pit bottom. A 6-in., cast iron, underground waste line originated at the pit tank in the reactor building and ran approximately 68 ft to the seepage pit. The soil in the seepage pit contained low-level radioactive contamination. The soil surface was removed to a depth of 2.5 ft and shipped to the Radioactive Waste Management Complex (RWMC). The waste line that contained fixed contamination was removed and also sent to the RWMC. The pit was backfilled with radiologically clean soil, reducing the surface activity to background. A permanent marker was erected over the backfilled pit to indicate that presence of residual subsurface radioactive contamination. 5 references, 26 figures, 3 tables

Problems and prospects of modern methods of business analysis in the process of assessment of solvency of borrowers

Directory of Open Access Journals (Sweden)

Aptekar Saveliy S.

2013-03-01

Full Text Available The goal of the article is a comparative analysis of modern methods of business analysis in the process of assessment of solvency of borrowers of Ukrainian commercial banks, study of prospects and problems of the use of methods in the credit process. In the result of the study the article systemises and considers the conduct of the credit process of Ukrainian commercial banks. It becomes clear from result of the study that it is impossible to obtain a single assessment of solvency of a borrower with generalisation of numerical and non-numerical data. Assessment of qualified analysts is required for a justified assessment of solvency apart from information represented in numbers. Improvement of approaches to assessment of solvency of borrowers and adaptation of the existing foreign experience in this field to specific features of formation of solvency of Ukrainian borrowers are important tasks for the Ukrainian banking system. Prospects of further studies in this direction are establishment of importance of the conduct of business analysis and its key role in assessment of solvency of borrowers as a main instrument of minimisation of the credit risk. Improvement of this sphere of analytical work in Ukrainian banks should be carried out in the following main directions: study and analysis of qualitative indicators of business activity; analysis of main sections of the business plan; expansion of the composition of indicators of the financial analysis for obtaining information; conduct of analysis of possible sources of repayment of loan liabilities; and active use of analysis of cash flows of an enterprise.

Pitting corrosion susceptibility study of zirconium alloys in the presence of the chloride ions

International Nuclear Information System (INIS)

Radulescu, M.; Pirvan, I.; Velciu, L.

1997-01-01

Pitting corrosion mechanism is specific to metal/aggressive environment systems. The influence of both components of the process was thoroughly investigated. After reviewing the principal steps of the pitting corrosion and of the electrochemical reactions associated, there were presented the physico-chemical methods used for the determination of the corrosion pitting parameters completed with the metallographic techniques of investigation of the attacked surfaces. Reported are the results of determinations of the pit initiation (E np ) and pit passivation (E pp ) potentials in the systems Zy-4 (Zr)/ Cl - provided from the following solutions: HCl, FeCl 3 , NaCl and LiCl. In the case of the last two solutions, the measurements were carried out also in the range of alkaline pH values. It was also determined the dependence of E np and E pp potential on the Cl - ions concentration in NaCl and HCl solutions, and also the reaction order 'n' in presence of several chloride concentration. Finally, on the basis of the experimental data, we established the kinetic characteristics specific to different steps of pitting. (authors)

Field test on sand compaction pile method with copper slag sand; Dosuisai slag wo mochiita SCP koho no shiken seko

Energy Technology Data Exchange (ETDEWEB)

Minami, K.; Matsui, H.; Naruse, E.; Kitazume, M. [Port and Harbour Research Inst., Kanagawa (Japan)

1997-09-20

This paper describes the sand compaction pile (SCP) method using copper slag sand. The SCP method is a method by which sand compaction piles are constructed in the ground, and improvement can be obtained in a short period. This method has been widely used even in the port areas for enhancing the bearing power of soft clay ground and the lateral resistance of sheet pile. A great deal of sand is required as a material. The sand requires high permeability, proper size distribution with less fine particle fraction content, easy compaction property with enough strength, and easy discharging property from the casing of construction machines as required properties. Recently, it becomes hard to secure proper sand materials. The copper slag sand is obtained from refining process of copper as a by-product which is quenched in water flow and crushed in water. The copper slag sand has higher particle density than that of sand, excellent permeability, and similar size distribution to that of sand. From compaction drainage triaxial compression test and permeability test, it was found that the mechanical properties of copper slag sand did not change by the crushing of grains with keeping excellent permeability. Through the test construction, applicability of the copper slag sand to the SCP method could be confirmed as an alternate material of sand. 17 refs., 9 figs., 4 tabs.

On the detection of corrosion pit interactions using two-dimensional spectral analysis

International Nuclear Information System (INIS)

Jarrah, Adil; Nianga, Jean-Marie; Iost, Alain; Guillemot, Gildas; Najjar, Denis

2010-01-01

A statistical methodology for detecting pits interactions based on a two-dimensional spectral analysis is presented. This method can be used as a tool for the exploratory analysis of spatial point patterns and can be advanced as an alternative of classical methods based on distance. One of the major advantages of the spectral analysis approach over the use of classical methods is its ability to reveal more details about the spatial structure like the scale for which pits corrosion can be considered as independent. Furthermore, directional components of pattern can be investigated. The method is validated in a first time using numerical simulations on random, regular and aggregated structures. The density of pits, used in the numerical simulations, corresponds to that assessed from a corroded aluminium sheet. In a second time, this method is applied to verify the independence of the corrosion pits observed on the aforementioned aluminium sheet before applying the Gumbel theory to determine the maximum pit depth. Indeed, the property of independence is a prerequisite of the Gumbel theory which is one of the most frequently used in the field of safety and reliability.

Design-only conceptual design report for pit disassembly and conversion facility. Rev 0

International Nuclear Information System (INIS)

Zygmunt, S.; Christensen, L.; Richardson, C.

1997-01-01

This design-only conceptual design report (DOCDR) was prepared to support a funding request by the Department of Energy (DOE)-Office of Fissile Material Disposition (OFMD) for engineering design of the Pit Disassembly and Conversion Facility (PDCF) Project No. 99-D-141. The PDCF will be used to disassemble the nation's inventory of surplus nuclear weapons pits and convert the plutonium recovered from those pits into a form suitable for storage, international inspection, and final disposition. The PDCF is a complex consisting of a hardened building that will contain the plutonium processes in a safe and secure manner, and conventional buildings and structures that will house support personnel, systems, and equipment. The PDCF uses the Advanced Recovery and Integrated Extraction System (ARIES), a low waste, modular pyroprocessing system to convert pits to plutonium oxide. The PDCF project consists of engineering and design, and construction of the buildings and structures, and engineering and design, procurement, installation, testing and start-up of equipment to disassemble pits and convert plutonium in pits to oxide form. The facility is planned to operate for 10 years, averaging 3.5 metric tons (3.86 tons) of plutonium metal per year. On conclusion of operations, the PDCF will be decontaminated and decommissioned

Design-only conceptual design report for pit disassembly and conversion facility. Rev 0

Energy Technology Data Exchange (ETDEWEB)

Zygmunt, S.; Christensen, L.; Richardson, C.

1997-12-12

This design-only conceptual design report (DOCDR) was prepared to support a funding request by the Department of Energy (DOE)-Office of Fissile Material Disposition (OFMD) for engineering design of the Pit Disassembly and Conversion Facility (PDCF) Project No. 99-D-141. The PDCF will be used to disassemble the nation`s inventory of surplus nuclear weapons pits and convert the plutonium recovered from those pits into a form suitable for storage, international inspection, and final disposition. The PDCF is a complex consisting of a hardened building that will contain the plutonium processes in a safe and secure manner, and conventional buildings and structures that will house support personnel, systems, and equipment. The PDCF uses the Advanced Recovery and Integrated Extraction System (ARIES), a low waste, modular pyroprocessing system to convert pits to plutonium oxide. The PDCF project consists of engineering and design, and construction of the buildings and structures, and engineering and design, procurement, installation, testing and start-up of equipment to disassemble pits and convert plutonium in pits to oxide form. The facility is planned to operate for 10 years, averaging 3.5 metric tons (3.86 tons) of plutonium metal per year. On conclusion of operations, the PDCF will be decontaminated and decommissioned.

Métodos para predição de bitter pit em maçãs 'Fuji' e 'Braeburn' Methods for bitter pit prediction in Fuji and Braeburn apples

Directory of Open Access Journals (Sweden)

Ivan Sestari

2009-07-01

Full Text Available Experimentos foram conduzidos com objetivo de avaliar a eficiência de métodos para predição da ocorrência de bitter pit em maçãs 'Fuji' e 'Braeburn' em duas épocas de amostragem. Os frutos, provenientes de seis pomares distintos, três para cada cultivar, foram coletados antecipadamente (20 dias em relação à colheita e na data prevista para a colheita comercial. Os métodos de predição utilizados foram: a infiltração dos frutos com solução 0,10M MgCl2 mais 0,01% Tween-20 e 0,4M de sorbitol; b imersão dos frutos em solução com 2500nL L-1 de ethephon mais 0,01% Tween-20. Os frutos foram armazenados em atmosfera controlada (AC por cinco meses mais 12 dias, a 20°C, simulando a incidência real de bitter pit em armazenamento comercial. Cada tratamento foi constituído por quatro repetições de 25 frutos. A incidência e severidade de bitter pit, prevista por ambos os métodos foi semelhante à ocorrência real de bitter pit após o armazenamento em atmosfera controlada para cada uma das cultivares utilizadas, quando os frutos foram amostrados antecipadamente em relação à colheita comercial. Na avaliação realizada com frutos amostrados na colheita comercial, nenhum dos métodos foi capaz de prever a incidência de bitter pit após o armazenamento de maneira confiável. Para ambas as cultivares, a infiltração com magnésio e a imersão dos frutos em ethephon só são eficientes na predição da incidência de bitter pit em frutos coletados 20 dias antes da colheita comercial.Experiments were carried out with objective to evaluate the efficiency of methods for bitter pit prediction in 'Fuji' and 'Braeburn' apples sampled at two harvest dates. Fruits from 6 orchards, three for each cultivar, were sampled earlier (20 days before harvest and at commercial harvest date. The prediction methods assessed were: infiltration of apples with 0.10M MgCl2 solution containing 0.01% Tween-20 and 0.4M sorbitol; and immersion of fruits in 2

Evaluation of PIT-tagging in cyprinids

DEFF Research Database (Denmark)

Skov, Christian; Brodersen, J.; Brönmark, C.

2005-01-01

Laboratory and field experiments were used to investigate how different marking procedures, with 23 mm PIT (passive integrated transponders) - tags. affected mortality, body condition and tag expulsion in small roach Rutilus rutilus and rudd Scardinus erythrophthalmus (117 to 163 mm total length...