Consolidation of the formation sand by chemical methods

Directory of Open Access Journals (Sweden)

Mariana Mihočová

2006-10-01

Full Text Available The sand control by consolidation involves the process of injecting chemicals into the naturally unconsolidated formation to provide an in situ grain-to-grain cementation. The sand consolidation chemicals are available for some 30 years. Several types of consolidating material were tried. Presently available systems utilize solidified plastics to provide the cementation. These systems include phenol resin, phenol-formaldehyde, epoxy, furan and phenolic-furfuryl.The sand consolidation with the steam injection is a novel technique. This process provides a highly alkaline liquid phase and temperatures to 300 °C to geochemically create cements by interacting with the dirty sand.While the formation consolidation has widely applied, our experience has proved a high level of success.

Effect of manufactured sand on the durability characteristics of concrete

Directory of Open Access Journals (Sweden)

S. S. SARAVANAN

2016-12-01

Full Text Available Concrete is the most sought after material due to increase in construction activities and infrastructural developments. Availability of natural sand is decreasing thereby increase in the cost of construction. In the present work undertaken, an attempt has been made to give an alternative to natural sand. Optimization of replacement of natural sand with manufactured sand in concrete, durability studies such as water absorption, rapid chloride permeability test, sorptivity, acid resistance, alkaline resistance, impact resistance and abrasion resistance of M40 and M50 grades of concrete have been studied with manufactured sand as fine aggregate and compared the results with the conventional sand concrete. The results shows that there is an increase in the durability properties up to 70 % level of replacements of sand with manufactured sand as fine aggregate and for 100 % use of manufactured sand also gives the better durability than the conventional sand concrete.

Retorting of bituminous sands

Energy Technology Data Exchange (ETDEWEB)

Chaney, P E; Ince, R W; Mason, C M

1872-09-26

This method of recovering oil from mined tar sands involves forming compacted tar sands pieces by special conditioning treatment that provides low internal permeability. The compacted pieces are then retorted in fixed bed form. The conditioning treatment can involve rolling of preformed pellets, compaction in a mold or pressure extrusion. Substantial collapsing of the bed during retorting is avoided. (9 claims) (Abstract only - original article not available from T.U.)

Sedimentary characteristics and controlling factors of shelf sand ridges in the Pearl River Mouth Basin, northeast of South China Sea

Directory of Open Access Journals (Sweden)

Xiangtao Zhang

2017-04-01

Full Text Available Shelf sand ridge is a significant type of reservoir in the continental marginal basin, and it has drawn so much attention from sedimentologists and petroleum geologists. We were able to investigate the morphology, distribution, and sedimentary structures of shelf sand ridges systematically in this study based on the integration of high-resolution 3D seismic data, well logging, and cores. These shelf sand ridges are an asymmetrical mound-like structure in profiles, and they developed on an ancient uplift in the forced regression system tract and are onlapped by the overlying strata. In the plane, shelf sand ridges present as linear-shaped, which is different from the classical radial pattern; not to mention, they are separated into two parts by low amplitude tidal muddy channels. Corrugated bedding, tidal bedding, and scouring features are distinguished in cores of shelf sand ridges together with the coarsening up in lithology. All of these sedimentary characteristics indicate that shelf sand ridges deposited in the Pearl River Mouth Basin are reconstructed by the tidal and coastal current.

MORPHOMETRIC CHARACTERIZATION OF THE SAND FRACTION IN A SAND GRAIN IMAGE CAPTURE SYSTEM1

Directory of Open Access Journals (Sweden)

Lucimar Arruda Viana

Full Text Available ABSTRACT Morphology studies assume significant importance in analysis of phenomena of granular systems packaging, in particular with a view to the use of the technique of soil stabilization named particle size correction in forest roads. In this context, this study aimed to develop and operationalize a Sand Grain Image Capture System and, hereby, determine the morphological indices of the sand fractions of two sandy soils called João Pinheiro (JP and Cachoeira da Prata (CP. Soil samples, air-dried, were sieved (2.0 mm nominal mesh size for removal of gravels. The materials that passed through the sieve were subjected to dispersion, washing in 0.053 mm nominal mesh size sieve, removal of organic matter and iron oxides to obtain the clean sand fractions. Subsequently, each soil sample was sieved for separation into twelve classes, between the diameters of 0.149 mm and 1.190 mm, using a Rotap shaker. Next, tests were carried out to characterize the morphometric attributes of the twelve classes of sand fractions of the soils studied. For validation of the performance of the Sand Grain Image Capture System, the results were compared to those obtained using a standard procedure for image analysis. The analysis of the results led to the following conclusions: (i the sand fraction of the JP soil presented higher values for the morphometric indices roundness, elongation and compactness compared to sand fraction of the CP soil; and (ii the Sand Grain Image Capture System worked properly, with practicality.

Holocene beach buildup and coastal aeolian sand incursions off the Nile littoral cell

Science.gov (United States)

Roskin, Joel; Sivan, Dorit; Shtienberg, Gilad; Porat, Naomi; Bookman, Revital

2017-04-01

Israel's coastal plain is abundant with sand originating from the Nile littoral cell. The inland windblown loose sand has formed 3-6 km wide lobe-like sand and dune fields currently comprised of foredunes, linear and northeasterly facing transverse and parabolic dunes that are currently stabilized by vegetation. This study reviews the architecture and history of the these dune fields aiming to: (a) Date the timings of beach accretion, and sand and dune incursions. (b) Discriminate between natural and human-induced forcing factors of sand mobilization and stabilization in time and space. (c) Present a model of the dunescape development. (d) Assess scenarios of sand transport in the future charcaterized by intense human impact and climate change. Luminescence ages, radiocarbon dates and relative ages from previously published geological and archaeological reports, historical texts, together with new optically stimulated luminescence (OSL) ages and stratigraphic and sedimentological data are analyzed. The deposition, mobilizations and preservation of the sand bodies, initially induced by the decline in sea level rise at 6-4 ka, were later controlled by historic land-use intensity and modern land-use/negligence practices. At 6 ka, beach sand buildup rapidly started. Where aeolianite ridges bordered the coast, pulses of sand with biogenic carbonate grains unconformably draped the ridges and rapidly consolidated into a distinct sandy calcarenite unit. Further east, sand sheets and low dunes partly pedogenized following their incursion, but did not cement. The water retention capacities of the sand sheets enabled the establishment of a sand-stabilizing vegetation cover that probably became an attractive environment for fuel and grazing. The growing Hellenistic-Roman-Byzantine ( 2.4-1.3 ka) populations probably led to increased consumption and massive destruction of sand stabilizing vegetation, enabling sand erodibility and mobilization during winter storms. The sand

Contribution of sand-associated enterococci to dry weather water quality.

Science.gov (United States)

Halliday, Elizabeth; Ralston, David K; Gast, Rebecca J

2015-01-06

Culturable enterococci and a suite of environmental variables were collected during a predominantly dry summer at a beach impacted by nonpoint source pollution. These data were used to evaluate sands as a source of enterococci to nearshore waters, and to assess the relationship between environmental factors and dry-weather enterococci abundance. Best-fit multiple linear regressions used environmental variables to explain more than half of the observed variation in enterococci in water and dry sands. Notably, during dry weather the abundance of enterococci in dry sands at the mean high-tide line was significantly positively related to sand moisture content (ranging from sands. Tidal forcing modulated the abundance of enterococci in the water, as both turbidity and enterococci were elevated during ebb and flood tides. The probability of samples violating the single-sample maximum was significantly greater when collected during periods with increased tidal range: spring ebb and flood tides. Tidal forcing also affected groundwater mixing zones, mobilizing enterococci from sand to water. These data show that routine monitoring programs using discrete enterococci measurements may be biased by tides and other environmental factors, providing a flawed basis for beach closure decisions.

Swelling characteristics of sand-bentonite mixtures under one-dimensional stress

International Nuclear Information System (INIS)

Cui, Hongbin; Sun, De'an; Matsuoka, Hajime; Xu Yongfu

2004-01-01

Based on the concept that the maximum water volume absorbed by unit volume of montmorillonite is constant, the swelling deformation of sand-bentonite mixtures is uniquely characterized using the void ratio of montmorillonite, which is defined by the ratio of water volume to montomorillonite volume. The relationship between the montmorillonite void ratio and overburden pressure at fully swelling is independent of the initial compaction condition and the sand-bentonite mixture ratio, and is a linear line in their log scale. When overburden pressure is large enough and/or the bentonite ratio of the mixture is small, the measured plots deviate from the line. A method for predicting the limited overburden pressure which is linearly correlated with the montmorillonite void ratio is proposed and verified using the concept of the skeleton void ratio. (author)

Hydraulic properties of domestic bentonite-sand mixture as a backfill material in the high-level waste repository

Energy Technology Data Exchange (ETDEWEB)

Cho, Won Jin; Lee, Jae Owan; Kang, Chul Hyung [Korea Atomic Energy Research Institute, Taejeon (Korea)

2000-02-01

This study is intended to investigate the effect of dry density and sand content on hydraulic conductivities of bentonite-sand mixtures. The hydraulic conductivities of bentonite-sand mixtures with dry densities of 1.6 and 1.8 Mg/m{sup 3} are lower than 10{sup -11} m/s if their sand contents are less than 70 wt%. However at the sand content of 90 wt%, the hydraulic conductivities increase sharply. In the case of sand contents not exceeding 70 wt%, the logarithm of the hydraulic conductivity of bentonite-sand mixture increase linearly with increasing sand content. The hydraulic conductivity of the mixture can be explained using 'effective clay dry density' concept. 16 refs., 21 figs., 5 tabs. (Author)

High temperature thermal energy storage in moving sand

Science.gov (United States)

Turner, R. H.; Awaya, H. I.

1978-01-01

Several high-temperature (to 500 C) heat-storage systems using sand as the storage medium are described. The advantages of sand as a storage medium include low cost for sand, widespread availability, non-toxicity, non-degradation characteristics, easy containment, and safety. The systems considered include: stationary sand with closely spaced tubes throughout the volume, the use of a fluidized bed, use of conveyor belt transporter, and the use of a blower rapid transport system. For a stationary sand bed, very close spacing of heat transfer tubes throughout the volume is required, manifesting as high power related system cost. The suggestion of moving sand past or around pipes is intended to reduce the power related costs at the penalty of added system complexity. Preliminary system cost estimates are offered. These rough calculations indicate that mobile sand heat storage systems cost less than the stationary sand approach.

Numerical analysis of biological clogging in two-dimensional sand box experiments

DEFF Research Database (Denmark)

Kildsgaard, J.; Engesgaard, Peter Knudegaard

2001-01-01

Two-dimensional models for biological clogging and sorptive tracer transport were used to study the progress of clogging in a sand box experiment. The sand box had been inoculated with a strip of bacteria and exposed to a continuous injection of nitrate and acetate. Brilliant Blue was regularly...... injected during the clogging experiment and digital images of the tracer movement had been converted to concentration maps using an image analysis. The calibration of the models to the Brilliant Blue observations shows that Brilliant Blue has a solid biomass dependent sorption that is not compliant...... with the assumed linear constant Kd behaviour. It is demonstrated that the dimensionality of sand box experiments in comparison to column experiments results in a much lower reduction in hydraulic conductivity Žfactor of 100. and that the bulk hydraulic conductivity of the sand box decreased only slightly. However...

Sand transportation and reverse patterns over leeward face of sand dune

Science.gov (United States)

Jiang, Hong; Dun, Hongchao; Tong, Ding; Huang, Ning

2017-04-01

Sand saltation has complex interactions with turbulent flow and dune form. Most models of wind-blown sand consider ideal circumstances such as steady wind velocity and a flat surface, and the bulk of data on wind flow and sand transport over an individual dune has focused mostly on the influence of dune shape or inter-dune space on the wind flow, neglecting the effect of morphology on sand saltation, particularly airflow and sand transportation over the leeward slope. Wind flow structures over the leeward slope of sand dunes have a fundamental influence on the organization of sand dunes. In order to understand sand dune dynamics, lee face airflow and sediment transportation should be paid more attention. Previous field observations could not measure turbulent flow structure well because of the limited observation points and the influence of experiment structure on wind field. In addition, the reverse sand particles over leeward face could not be collected by sand trap in field. Numerous field observations could not measure turbulent flow structure because of the limited observation points and the influence of experimental structures on the wind field. In addition, the reverse transport of sand particles over leeward face could not be collected by sand traps in field. Therefore, this paper aims to investigate the turbulent flow structure and sand transport pattern over the leeward slope. A numerical model of sand saltation over slope terrain is constructed, which also considers the coupling effects between air flow and sand particles. The large eddy simulation method is used to model turbulent flow. Sand transport is simulated by tracking the trajectory of each sand particle. The results show that terrain significantly alters the turbulent air flow structure and wind-blown sand movement, especially over the leeward slope. Here, mass flux increases initially and then decreases with height in the reversed flow region in the direction of wind flow, and the mass flux

Aeolian sand transport and aeolian deposits on Venus: A review

Science.gov (United States)

Kreslavsly, Mikhail A.; Bondarenko, Nataliya V.

2017-06-01

We review the current state of knowledge about aeolian sand transport and aeolian bedforms on planet Venus. This knowledge is limited by lack of observational data. Among the four planetary bodies of the Solar System with sufficient atmospheres in contact with solid surfaces, Venus has the densest atmosphere; the conditions there are transitional between those for terrestrial subaerial and subaqueous transport. The dense atmosphere causes low saltation threshold and short characteristic saltation length, and short scale length of the incipient dunes. A few lines of evidence indicate that the typical wind speeds exceed the saltation threshold; therefore, sand transport would be pervasive, if sand capable of saltation is available. Sand production on Venus is probably much slower than on the Earth; the major terrestrial sand sinks are also absent, however, lithification of sand through sintering is expected to be effective under Venus' conditions. Active transport is not detectable with the data available. Aeolian bedforms (transverse dunes) resolved in the currently available radar images occupy a tiny area on the planet; however, indirect observations suggest that small-scale unresolved aeolian bedforms are ubiquitous. Aeolian transport is probably limited by sand lithification causing shortage of saltation-capable material. Large impact events likely cause regional short-term spikes in aeolian transport by supplying a large amount of sand-size particles, as well as disintegration and activation of older indurated sand deposits. The data available are insufficient to understand whether the global aeolian sand transport occurs or not. More robust knowledge about aeolian transport on Venus is essential for future scientific exploration of the planet, in particular, for implementation and interpretation of geochemical studies of surface materials. High-resolution orbital radar imaging with local to regional coverage and desirable interferometric capabilities is the

Sand (CSW4)

CSIR Research Space (South Africa)

Estuarine and Coastal Research Unit

1982-12-01

Full Text Available This report is one of a series on Cape Estuaries being published under the general title "The Estuaries of the Cape, Part 2". The report provides information on sand estuary: historical background, abiotic and biotic characteristics. It is pointed...

A Improved Seabed Surface Sand Sampling Device

Science.gov (United States)

Luo, X.

2017-12-01

In marine geology research it is necessary to obtain a suf fcient quantity of seabed surface samples, while also en- suring that the samples are in their original state. Currently,there are a number of seabed surface sampling devices available, but we fnd it is very diffcult to obtain sand samples using these devices, particularly when dealing with fne sand. Machine-controlled seabed surface sampling devices are also available, but generally unable to dive into deeper regions of water. To obtain larger quantities of seabed surface sand samples in their original states, many researchers have tried to improve upon sampling devices,but these efforts have generally produced ambiguous results, in our opinion.To resolve this issue, we have designed an improved andhighly effective seabed surface sand sampling device that incorporates the strengths of a variety of sampling devices. It is capable of diving into deepwater to obtain fne sand samples and is also suited for use in streams, rivers, lakes and seas with varying levels of depth (up to 100 m). This device can be used for geological mapping, underwater prospecting, geological engineering and ecological, environmental studies in both marine and terrestrial waters.

Biodegradable materials as binders for IVth generation moulding sands

OpenAIRE

K. Major-Gabry

2015-01-01

This paper focuses on the possibility of using the biodegradable materials as binders (or parts of binders?compositions) for foundry moulding and core sands. Results showed that there is a great possibility of using available biodegradable materials as foundry moulding sand binders. Using biodegradable materials as partial content of new binders, or additives to moulding sands may not only decrease the toxicity and increase reclamation ability of tested moulding sands, but also accelerate the...

Micromechanical investigation of sand migration in gas hydrate-bearing sediments

Science.gov (United States)

Uchida, S.; Klar, A.; Cohen, E.

2017-12-01

Past field gas production tests from hydrate bearing sediments have indicated that sand migration is an important phenomenon that needs to be considered for successful long-term gas production. The authors previously developed the continuum based analytical thermo-hydro-mechanical sand migration model that can be applied to predict wellbore responses during gas production. However, the model parameters involved in the model still needs to be calibrated and studied thoroughly and it still remains a challenge to conduct well-defined laboratory experiments of sand migration, especially in hydrate-bearing sediments. Taking the advantage of capability of micromechanical modelling approach through discrete element method (DEM), this work presents a first step towards quantifying one of the model parameters that governs stresses reduction due to grain detachment. Grains represented by DEM particles are randomly removed from an isotropically loaded DEM specimen and statistical analyses reveal that linear proportionality exists between the normalized volume of detached solids and normalized reduced stresses. The DEM specimen with different porosities (different packing densities) are also considered and statistical analyses show that there is a clear transition between loose sand behavior and dense sand behavior, characterized by the relative density.

Sand waves on an epicontinental shelf: Northern Bering Sea

Science.gov (United States)

Field, M.E.; Nelson, C.H.; Cacchione, D.A.; Drake, D.E.

1981-01-01

Sand waves and current ripples occupy the crests and flanks of a series of large linear sand ridges (20 km ?? 5 km ?? 10 m high) lying in an open-marine setting in the northern Bering Sea. The sand wave area, which lies west of Seward Peninsula and southeast of Bering Strait, is exposed to the strong continuous flow of coastal water northward toward Bering Strait. A hierarchy of three sizes of superimposed bedforms, all facing northward, was observed in successive cruises in 1976 and 1977. Large sand waves (height 2 m; spacing 200 m) have smaller sand waves (height 1 m; spacing 20 m) lying at a small oblique angle on their stoss slopes. The smaller sand waves in turn have linguoid ripples on their stoss slopes. Repeated studies of the sand wave fields were made both years with high-resolution seismic-reflection profiles, side-scan sonographs, underwater photographs, current-meter stations, vibracores, and suspended-sediment samplers. Comparison of seismic and side-scan data collected along profile lines run both years showed changes in sand wave shape that indicate significant bedload transport within the year. Gouge marks made in sediment by keels of floating ice also showed significantly different patterns each year, further documenting modification to the bottom by sediment transport. During calm sea conditions in 1977, underwater video and camera observations showed formation and active migration of linguoid and straight-crested current ripples. Current speeds 1 m above the bottom were between 20 and 30 cm/s. Maximum current velocities and sand wave migration apparently occur when strong southwesterly winds enhance the steady northerly flow of coastal water. Many cross-stratified sand bodies in the geologic record are interpreted as having formed in a tidal- or storm-dominated setting. This study provides an example of formation and migration of large bedforms by the interaction of storms with strong uniform coastal currents in an open-marine setting. ?? 1981.

Sand and Gravel Deposits

Data.gov (United States)

Vermont Center for Geographic Information — This dataset is a statewide polygon coverage of sand, gravel, and stone resources. This database includes the best data available from the VT Agency of Natural...

The morphodynamics of tidal sand waves: A model overview

NARCIS (Netherlands)

Besio, G.; Blondeaux, P.; Brocchini, M.; Hulscher, Suzanne J.M.H.; Idier, Deborah; Knaapen, Michiel; Nemeth, Attila; Roos, Pieter C.; Vittori, G.

2008-01-01

This paper reviews recent theoretical studies of sand waves which are rhythmic large-scale bedforms observed in the continental shelf far from the near-shore region. Emphasis is given to the investigations carried out in the framework of the EU research project HUMOR. First, the results of linear

Gasification of oil sand coke: review

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E. [IMAF Group, Ottawa, ON (Canada)

1998-08-01

The production of synthetic crude from the tar sands in Western Canada has been steadily increasing. Most of the delayed coke produced by Suncor is combusted on site, whereas all fluid coke produced by Syncrude is stockpiled.The database on the chemical and physical properties of the oil sand coke, including the composition and fusion properties of the mineral matter, has been established. The reactivity of the coke was determined by oxygen chemisorption, fixed bed and fluid bed bench scale gasification and pilot plant gasification. The reactivity of the oil sand coke for gasification is rather low and comparable to high rank coals, such as anthracite. Slurrability tests revealed that a solid concentration in water, approaching 70 wt%, can be achieved. Gasification is the front runner among clean technologies for the conversion of carbonaceous solids to useful products. Several commercial gasifiers are available to cover the wide range of severity. Because of the low reactivity of oil sands coke, high severity conditions are required to achieve high gasification conversion. Such conditions can be attained in entrained bed gasifiers. Gasifiers employing both dry and slurry feeding systems are suitable. A high efficiency, low SO{sub x} and NO{sub x} emissions, as well as a low solid waste production are among the key advantages of the gasification technology compared with thecompeting technologies. Commercial gasification of oil sands coke is delayed because of the availability of natural gas on the site of the upgrading plants. Potential for the transportation of the oil sand coke to USA for electricity generation using the integrated gasification combined-cycle (IGCC) technology was evaluated. 27 refs., 17 figs., 9 tabs.

Investigation of TL properties of sand collected from sewage sludge as an ''in situ'' dosimeter in radiation disinfection

International Nuclear Information System (INIS)

Benny, P.G.; Bhatt, B.C.

1996-01-01

Thermoluminescence (TL) properties of sand, collected from sewage sludge, were studied after extensive cleaning procedures. In the sand samples treated with either hydrogen peroxide (H 2 O 2 ) or hydrofluoric acid (HF), there was a prominent TL peak at about 220 o C after γ-irradiation and 120 o C, 20 min post-irradiation annealing treatment. The dose vs TL response curves in hydrogen-peroxide-treated and HF-treated sand samples were found to be linear up to 30 and 100 Gy, respectively, beyond which they were supra-linear. The extent of post-irradiation fading in the sand sample, which was treated with H 2 O 2 and post-irradiation annealed at 120 o C for 20 min, was observed to be 8% after 21 days, while no detectable fading was observed for the sample which was HF treated and annealed at 120 o C for 20 min after γ-irradiation. Therefore, H 2 O 2 - as well as HF-treated sludge sand samples could be considered for use as in situ TL dosimeters for radiation disinfection of sewage sludge. (Author)

Influence of sand base preparation on properties of chromite moulding sands with sodium silicate hardened with selected methods

Directory of Open Access Journals (Sweden)

Stachowicz M.

2017-03-01

Full Text Available The paper presents a research on the relation between thermal preparation of chromite sand base of moulding sands containing sodium silicate, hardened with selected physical and chemical methods, and structure of the created bonding bridges. Test specimens were prepared of chromite sand - fresh or baked at 950°C for 10 or 24 hours - mixed with 0.5 wt.% of the selected non-modified inorganic binder and, after forming, were hardened with CO2 or liquid esters, dried traditionally or heated with microwaves at 2.45 GHz. It was shown on the grounds of SEM observations that the time of baking the base sand and the hardening method significantly affect structure of the bonding bridges and are correlated with mechanical properties of the moulding sands. It was found that hardening chromite-based moulding mixtures with physical methods is much more favourable than hardening with chemical methods, guaranteeing also more than ten times higher mechanical properties.

Compressive Strength of Compacted Clay-Sand Mixes

Directory of Open Access Journals (Sweden)

Faseel Suleman Khan

2014-01-01

Full Text Available The use of sand to improve the strength of natural clays provides a viable alternative for civil infrastructure construction involving earthwork. The main objective of this note was to investigate the compressive strength of compacted clay-sand mixes. A natural clay of high plasticity was mixed with 20% and 40% sand (SP and their compaction and strength properties were determined. Results indicated that the investigated materials exhibited a brittle behaviour on the dry side of optimum and a ductile behaviour on the wet side of optimum. For each material, the compressive strength increased with an increase in density following a power law function. Conversely, the compressive strength increased with decreasing water content of the material following a similar function. Finally, the compressive strength decreased with an increase in sand content because of increased material heterogeneity and loss of sand grains from the sides during shearing.

Eastern Scheldt Sand, Baskarp Sand No. 15

DEFF Research Database (Denmark)

Andersen, A. T; Madsen, E. B.; Schaarup-Jensen, A. L.

The present data report contains data from 13 drained triaxial tests, performed on two different sand types in the Soil Mechanics Laboratory at Aalborg University in March, 1997. Two tests have been performed on Baskarp Sand No. 15, which has already ken extensively tested in the Soil Mechanics...... Laboratory. The remaining 11 triaxial tests have ben performed on Eastern Scheldt Sand, which is a material not yet investigated at the Soil Mechanics Laboratory. In the first pari of this data report, the characteristics of the two sand types in question will be presented. Next, a description...... will described. In this connection, the procedure for preparation of the soil specimens will be presented, and the actual performance of the tests will be briefly outlined. Finally, the procedure for processing of the measurements from the laboratory in order to obtain usable data will be described. The final...

SPECIFIC RESISTANCE AND SPECIFIC INTENSITY OF BELT SANDING OF WOOD

Directory of Open Access Journals (Sweden)

Boleslaw Porankiewicz

2010-06-01

Full Text Available This paper examines and discusses the specific belt sanding resistance K (N·cm-2 and specific belt sanding intensity SI (g·cm-2·min-1, for wood of Pinus sylvestris L., Picea abies L., Quercus robra L., Acer pseudoplatanus L., Alnus glutinosa Gaertn., and Populus Nigra L., by different sanding pressure pS, different sanding grit NG number, and different wood grain angles Phi(v.

Design and Fabrication of a Foundry Sand Mixer Using Locally ...

African Journals Online (AJOL)

Most small foundry shops mix their sand manually which is not efficient since homogenous mix cannot be guaranteed and even when foundry mixer are available most of them are imported costing the nation huge foriegn exchange. A foundry sand mixer capable of mixing foundry sand has been designed and fabricated ...

In situ recovery of oil from Utah tar sand: a summary of tar sand research at the Laramie Energy Technology Center

Energy Technology Data Exchange (ETDEWEB)

Marchant, L.C.; Westhoff, J.D.

1985-10-01

This report describes work done by the United States Department of Energy's Laramie Energy Technology Center from 1971 through 1982 to develop technology for future recovery of oil from US tar sands. Work was concentrated on major US tar sand deposits that are found in Utah. Major objectives of the program were as follows: determine the feasibility of in situ recovery methods applied to tar sand deposits; and establish a system for classifying tar sand deposits relative to those characteristics that would affect the design and operation of various in situ recovery processes. Contents of this report include: (1) characterization of Utah tar sand; (2) laboratory extraction studies relative to Utah tar sand in situ methods; (3) geological site evaluation; (4) environmental assessments and water availability; (5) reverse combustion field experiment, TS-1C; (6) a reverse combustion followed by forward combustion field experiment, TS-2C; (7) tar sand permeability enhancement studies; (8) two-well steam injection experiment; (9) in situ steam-flood experiment, TS-1S; (10) design of a tar sand field experiment for air-stream co-injection, TS-4; (11) wastewater treatment and oil analyses; (12) economic evaluation of an in situ tar sand recovery process; and (13) appendix I (extraction studies involving Utah tar sands, surface methods). 70 figs., 68 tabs.

Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

Directory of Open Access Journals (Sweden)

Nirmala D.B.

2016-06-01

Full Text Available This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37 Orthogonal Arrays (OA with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering “Nominal the better” situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

Sustainable use of oil sands for geotechnical construction and road building

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2012-02-01

Full Text Available Oil sands are natural deposits of bituminous sand materials that are mined and processed for crude oil. They are routinely used in oil sand fields for building temporary and sometimes permanent roads serving mining and hauling activities. Although...

Food irradiation dosimetry using thermoluminescence of quartz sand

International Nuclear Information System (INIS)

Khan, H.M.; Ehlermann, D.A.E.

1993-01-01

Thermoluminescence of quartz sand, which is inert and concomitant to several food materials, has been investigated for applications in food irradiation dosimetry and detection of irradiated foods. The glow curves consist of at least three overlapping peaks from 100 to 420 C. The peak at lower temperature is not stable and decays quickly at room temperature. However, the peaks at higher temperature are stable and more useful for dosimetry work. The intensity of the peak at 360 C, measured using different optical filters, shows a linear response in the range of 0.05 to 23 kGy. Stability of these signals at different annealing temperatures has been investigated. Thermoluminescence from adhering minerals and contaminating dust in different food materials has been found useful for the detection of irradiation treatment. Since quartz is frequently one of these minerals, further computerized deconvolution of individual glow peaks from the complex glow curves of quartz sand was carried out which improves the dosimetric results. Possible applications of thermoluminescence of quartz sand in food irradiation dosimetry and detection of irradiated foods have been discussed. (orig.)

Evaluation of wettability of binders used in moulding sands

Directory of Open Access Journals (Sweden)

Hutera B.

2007-01-01

Full Text Available Binders used in moulding sand have the differential properties. One of the main parameters influencing on moulding sand properties is wettability of the sand grain by binding material. In the article some problems concerned with wettability evaluation have been presented and the importance of this parameter for quantity description of process occurring in system: binder- sand grain has been mentioned. The procedure of wetting angle measurement and operation of prototype apparatus for wettability investigation of different binders used in moulding sand have been described, as well as the results of wetting angle measurement for different binders at different conditions. The addition of little amount of proper diluent to binder results in the state of equilibrium reached almost immediately. Such addition can also reduce the value of equilibrium contact angle. The uniform distribution of binder on the surface of the sand grains and reducing of the required mixing time can be obtained. It has also a positive effect on the moulding sand strength.

The Geodiversity in Drift Sand Landscapes of The Netherlands

Science.gov (United States)

van den Ancker, Hanneke; Jungerius, Pieter Dirk; Riksen, Michel

2015-04-01

metres high. They are common near villages. They originated through sand blown from fallow agricultural fields and local overgrazing. They vary in age from prehistoric to modern time and are now mostly planted with forests. Third are the linear drift sand areas with one to three metre high ridges that align old roads and originated through dust whirled up by horses and carriages over many centuries. They also occurs within drift sands of the first system. In the re-stabilization of reactivated drift sands, differences in geodiversity on a still more detailed scale are important (Ancker, Jungerius et al. 2013). Even a small change in slope can cause primary dunes to develop and stop wind erosion. Gradually the geodiversity aspects are recognized as relevant for the management of active and fossil drift sands, and also is becoming a management issue in itself. An important future research issue is the completion of the Drift Sand Atlas, a project that describes the geodiversity aspects of all drift sand areas of The Netherlands. This project has been retarded by lack of means. Knowledge of the geodiversity also is important for correct sampling of C14 and luminescence data. Other future research includes the processes that caused the formation of 'randwallen' (rim walls), rates of water and wind erosion and soil formation and links between flora, fauna and Natura 2000 species. References

Evaluate of head loss, sediment value and copper removal in sand media (rapid sand filter

Directory of Open Access Journals (Sweden)

Daneshi Navab

2014-06-01

Full Text Available Along with the technology development and increasing consumption of water resources, we are experiencing low qualities in the mentioned resources. Copper brings about serious environment al pollution, threatening human health and ecosystem. This metal found variously in water resources and industrial activities. Therefore, it needs to treat the water resources from these excessive amounts. Different methods have used for this reason but the most used method during recent years has been the absorption by economic absorbers such as sand. Rapid sand filters usually used in water and wastewater treatment plants for water clarification. In this research, a single layer gravity rapid sand filter has used to reduce different concentrations of copper. sediment value and head loss arising in filter media is simulated by using combination of Carman-Kozeny, Rose and Gregory models in different discharges of rapid sand filter. Results have shown that with increasing in discharge and decreasing in input copper concentration, arriving time to given head loss, is increasing. In addition, results demonstrated that with increasing in copper concentration in influent, removal efficiency is decreasing somewhat. Results of this research can applied in an appropriate design of rapid sand filter to copper removal, a prediction of rapid sand filter ability to copper removal and an estimation of arising head loss during filter work thus evaluating of time interval backwash. DOI: http://dx.doi.org/10.3126/ije.v3i2.10641 International Journal of the Environment Vol.3(2 2014: 276-286

Submarine sand ridges and sand waves in the eastern part of the China Sea

Science.gov (United States)

Wu, Ziyin; Li, Shoujun; Shang, Jihong; Zhou, Jieqiong; Zhao, Dineng; Liang, Yuyang

2016-04-01

Integrated with multi-beam and single-beam echo sounding data, as well as historical bathymetric data, submarine bathymetric maps of the eastern part of the China Sea, including the Bohai Sea, Huanghai Sea, and East China Sea, are constructed to systematically study submarine sand ridges and sand waves in the eastern part of the China Sea, combined with high-resolution seismic, sub-bottom profile and borehole data. Submarine sand ridges are extraordinarily developed in the eastern part of the China Sea, and 7 sand ridge areas can be divided from north to south, that is, the Laotieshan Channel sand ridge area in the Bohai Sea, the Korea Bay sand ridge area in the southern Huanghai Sea, the sand ridge area in the eastern Huanghai islands and the Huanghai Troughs, the Jianggang sand ridge area in the western Huanghai Sea, the sand ridge area in the East China Sea shelf, and the sand ridge and sand wave area in the Taiwan Strait and Taiwan Banks. The distribution area of the sand ridges and sand waves covers more than 450,000 km2, wherein ~10,000 km2 in the Bohai Bay, ~200,000 km2 in the Huanghai Sea, ~200,000 km2 in the East China Sea shelf, and ~40,000 km2 in the Taiwan Strait and Taiwan Banks, respectively. The great mass of sand ridges are distributed within water depth of 5-160 m, with a total length of over 160 km and a main width of 5-10 km. The inner structure of the sand ridges presents features of high-angle inclined beddings, with main lithology of sands, sand-mud alternations partly visible, and a small number of mud cores. Dating results indicate that the sand ridges in the eastern part of the China Sea are mainly developed in the Holocene. Sea-level variation dominates the sand ridge evolution in the eastern part of the China Sea since the LGM, and the sand ridges developed in the area of < 60m water depth are appeared in bad activity, meanwhile sand ridges with good activity are still developed in large scale.

Properties of dune sand concrete containing coffee waste

Directory of Open Access Journals (Sweden)

Mohamed Guendouz

2018-01-01

Full Text Available In the last years, an increase of coffee beverages consumption has been observed all over the world; and its consumption increases the waste coffee grounds which will become an environmental problems. Recycling of this waste to produce new materials like sand concrete appears as one of the best solutions for reduces the problem of pollution. This work aims to study the possibility of recycling waste coffee grounds (Spent Coffee Grounds (SCG as a fine aggregate by replacing the sand in the manufacturing of dune sand concrete. For this; sand concrete mixes were prepared with substitution of sand with the spent coffee grounds waste at different percentage (0%, 5%, 10%, 15% and 20% by volume of the sand in order to study the influence of this wastes on physical (Workability, bulk density and porosity, mechanical (compressive and flexural strength and Thermal (Thermal conductivity and thermal diffusivity properties of dune sand concrete. The results showed that the use of spent coffee grounds waste as partial replacement of natural sand contributes to reduce workability, bulk density and mechanical strength of sand concrete mixes with an increase on its porosity. However, the thermal characteristics are improved and especially for a level of 15% and 20% of substitution. So, it is possible to obtain an insulating material which can be used in the various types of structural components. This study ensures that reusing of waste coffee grounds in dune sand concrete gives a positive approach to reduce the cost of materials and solve some environmental problems.

High Temperature Thermal Properties of Bentonite Foundry Sand

Directory of Open Access Journals (Sweden)

Krajewski P.K.

2015-06-01

Full Text Available The paper presents results of measuring thermal conductivity and heat capacity of bentonite foundry sand in temperature range ambient - 900­­°C. During the experiments a technical purity Cu plate was cast into the green-sand moulds. Basing on measurements of the mould temperature field during the solidification of the casting, the temperature relationships of the measured properties were evaluated. It was confirmed that water vaporization strongly influences thermal conductivity of the moulding sand in the first period of the mould heating by the poured casting.

BH5047 type depth sand moisture-meter of high sensitivity

International Nuclear Information System (INIS)

Ji Changsong; Xie Liangnian; Zhang Shulan; Zhang Shuheng

2000-01-01

A new depth neutron moisture meter BH5047 has been developed. BH5047 neutron moisture meter is characterised by it is high sensitivity and used for sand water content measurement at concrete mixer. Calibration function is obtained by the Method of Least Squares. Linear correlation efficiency is as good as 0.9977

Fontainebleau Sand

DEFF Research Database (Denmark)

Leth, Caspar Thrane

2006-01-01

The report is a summary of results from laboratory tests in the geotechncial research group on Fontainebleau sand.......The report is a summary of results from laboratory tests in the geotechncial research group on Fontainebleau sand....

Spatial variation in deposition rate coefficients of an adhesion-deficient bacterial strain in quartz sand.

Science.gov (United States)

Tong, Meiping; Camesano, Terri A; Johnson, William P

2005-05-15

The transport of bacterial strain DA001 was examined in packed quartz sand under a variety of environmentally relevant ionic strength and flow conditions. Under all conditions, the retained bacterial concentrations decreased with distance from the column inlet at a rate that was faster than loglinear, indicating that the deposition rate coefficient decreased with increasing transport distance. The hyperexponential retained profile contrasted againstthe nonmonotonic retained profiles that had been previously observed for this same bacterial strain in glass bead porous media, demonstrating that the form of deviation from log-linear behavior is highly sensitive to system conditions. The deposition rate constants in quartz sand were orders of magnitude below those expected from filtration theory, even in the absence of electrostatic energy barriers. The degree of hyperexponential deviation of the retained profiles from loglinear behavior did not decrease with increasing ionic strength in quartz sand. These observations demonstrate thatthe observed low adhesion and deviation from log-linear behavior was not driven by electrostatic repulsion. Measurements of the interaction forces between DA001 cells and the silicon nitride tip of an atomic force microscope (AFM) showed that the bacterium possesses surface polymers with an average equilibrium length of 59.8 nm. AFM adhesion force measurements revealed low adhesion affinities between silicon nitride and DA001 polymers with approximately 95% of adhesion forces having magnitudes responsible for the low adhesion to silicon nitride, indicating that steric interactions from extracellular polymers controlled DA001 adhesion deficiency and deviation from log-linear behavior on quartz sand.

Effect of substrate size on sympatric sand darter benthic habitat preferences

Science.gov (United States)

Thompson, Patricia A.; Welsh, Stuart A.; Rizzo, Austin A.; Smith, Dustin M.

2017-01-01

The western sand darter, Ammocrypta clara, and the eastern sand darter, A. pellucida, are sand-dwelling fishes that have undergone range-wide population declines, presumably owing to habitat loss. Habitat use studies have been conducted for the eastern sand darter, but literature on the western sand darter remains sparse. To evaluate substrate selection and preference, western and eastern sand darters were collected from the Elk River, West Virginia, one of the few remaining rivers where both species occur sympatrically. In the laboratory, individuals were given the choice to bury into five equally available and randomly positioned substrates ranging from fine sand to granule gravel (0.12–4.0 mm). The western sand darter selected for coarse and medium sand, while the eastern sand darter was more of a generalist selecting for fine, medium, and coarse sand. Substrate selection was significantly different (p = 0.02) between species in the same environment, where the western sand darter preferred coarser substrate more often compared to the eastern sand darter. Habitat degradation is often a limiting factor for many species of rare freshwater fish, and results from this study suggest that western and eastern sand darters may respond differently to variations in benthic substrate composition.

Potential building sand deposits in Songkhla province area

Directory of Open Access Journals (Sweden)

Kooptarnond, K.

2002-10-01

Full Text Available An investigation of potential building sand deposits in Songkhla province area subdivided them into four regions according to their accumulation in various alluvial plains, meanders throughout alluvial deposits and residual soils. Four selected deposits, were Rattaphum-Khuan Niang, U-Taphao river, Na Mom, and Chana-Thepha regions. Information obtained from these deposits revealed a good correlation between the geomorphological features as interpreted from aerial photographs and those identified from vertical electrical resistivity sounding results. Sand samples were analysed for their physical and chemical properties. Petrographic studies were also undertaken to characterize the composition types, texture and shapes. An overview of the sand properties was used them to be within the acceptable limits for building sand. However, relatively high organic impurities and soundness were found in sand from Khuan Niang and Na Mom deposits. The result indicated a potential reconnaissance mineral resource of about 46 square kilometres.A reserve evaluation for natural building sand was carried out by using Geographic Information System (GIS. Maps of the various parameters considered were constructed in digital database format with the aid of Arc/Info and ArcView software. Overlay mapping and buffer zone modules were performed to evaluate inferred resources of building sand. The key parameters of analysis included the distance from transportation, distance from streams, lithology and thickness of sand layers. The remaining inferred sand total was of about 386 million cubic metres or about 1,021 million metric tons was therefore estimated, of which 60 percent lies in the Rattaphum-Khuan Niang region and 40 percent in the other regions.

Differences and commonalities impregnation of dry and wet sand

Directory of Open Access Journals (Sweden)

Maujuda МUZAFFAROVA

2014-09-01

Full Text Available The article is devoted to research new methods of physic-chemical methods of preventing deflation to protect railways and highways from such phenomena as exogenous sand drifts. In particular, first studied the possibility of using binders in sand wet state. Results can significantly extend the scope of the method, and identified with particular impregnation maintaining stability requirements protective cover reduces both the concentration previously recommended binders, and their costs, thereby securing implementation in practice of shifting sands resource-saving technology.

Effectiveness of SCADA Systems in Control of Green Sands Properties

Directory of Open Access Journals (Sweden)

Ignaszak Z.

2016-03-01

Full Text Available The paper undertakes an important topic of evaluation of effectiveness of SCADA (Supervisory Control and Data Acquisition systems, used for monitoring and control of selected processing parameters of classic green sands used in foundry. Main focus was put on process studies of properties of so-called 1st generation molding sands in the respect of their preparation process. Possible methods of control of this processing are presented, with consideration of application of fresh raw materials, return sand (regenerate and water. The studies conducted in one of European foundries were aimed at pointing out how much application of new, automated plant of sand processing incorporating the SCADA systems allows stabilizing results of measurement of selected sand parameters after its mixing. The studies concerned two comparative periods of time, before an implementation of the automated devices for green sands processing (ASMS - Automatic Sand Measurement System and MCM – Main Control Module and after the implementation. Results of measurement of selected sand properties after implementation of the ASMS were also evaluated and compared with testing studies conducted periodically in laboratory.

External costs of sand mining in rivers: evidence from South Africa.

CSIR Research Space (South Africa)

De Lange, Willem J

2009-05-01

Full Text Available river sand load content and excluding the impacts of dams and sand mining). Accounting for the impacts of dams on sediment yield decreased the estimate by at least 33 percent (Theron et al., 2008). An aerial survey identified thirty-one active sand... mining operations, extracting approximately 400 000 cubic meters of sand per year (a conservative estimate) in the eThekwini area (Theron et al., 2008). The estimated remaining sediment yield from rivers after accounting for the impacts of dams...

On the study of ricochet and penetration in sand, water and gelatin by spheres, 7.62 mm APM2, and 25 mm projectiles

Directory of Open Access Journals (Sweden)

John F. Moxnes

2016-04-01

Full Text Available We examine the ricochet and penetration behavior in sand, water and gelatin by steel spheres, 7.62 mm APM2 and 25 mm projectiles. A threshold impact angle (critical angle exists beyond which ricochet cannot occur. The Autodyn simulation code with the smooth particle hydrodynamic (SPH method and Impetus Afea Solver with the corpuscular model are used and the results are compared with experimental and analytical results. The resistance force in sand for spheres was proportional to a term quadratic in velocity plus a term linear in velocity. The drag coefficient for the quadratic term was 0.65. The Autodyn and Impetus Afea codes simulate too large penetration due to the lack of a linear velocity resistance force. Critical ricochet angles were consistent with analytical results in the literature. In ballistic gelatin at velocities of 50–850 m/s a drag coefficient of 0.30 fits the high speed camera recordings if a linear velocity resistance term is included. However, only a quadratic velocity resistance force with drag coefficient that varies with the Reynolds number also fits the measurements. The simulation of a sphere in water with Autodyn showed too large drag coefficient. The 7.62 mm APM2 core simulations in sand fit reasonable well for both codes. The 25 mm projectile ricochet simulations in sand show consistency with the high speed camera recordings. Computer time was reduced by one to two orders of magnitudes when applying the Impetus Afea Solver compared to Autodyn code due to the use of the graphics processing units (GPU.

New generation expandable sand screens

OpenAIRE

Syltøy, Christer

2014-01-01

Master's thesis in Petroleum engineering This thesis aims to give a general insight into sand control and various sorts of sand control measures and applications of sand control tools. Special focus will be given to expandable sand screens – a technology which came about in the late 1990’s through the use of flexible, expandable tubulars as base pipe in sand screens. More specifically Darcy’s Hydraulic Endurance Screens, a compliant sand screen system using hydraulic activation, and the fu...

Policy Analysis of Water Availability and Use Issues for Domestic Oil Shale and Oil Sands Development

Energy Technology Data Exchange (ETDEWEB)

Ruple, John [Univ. of Utah, Salt Lake City, UT (United States); Keiter, Robert [Univ. of Utah, Salt Lake City, UT (United States)

2010-03-01

Oil shale and oil sands resources located within the intermountain west represent a vast, and as of yet, commercially untapped source of energy. Development will require water, and demand for scarce water resources stands at the front of a long list of barriers to commercialization. Water requirements and the consequences of commercial development will depend on the number, size, and location of facilities, as well as the technologies employed to develop these unconventional fuels. While the details remain unclear, the implication is not – unconventional fuel development will increase demand for water in an arid region where demand for water often exceeds supply. Water demands in excess of supplies have long been the norm in the west, and for more than a century water has been apportioned on a first-come, first-served basis. Unconventional fuel developers who have not already secured water rights stand at the back of a long line and will need to obtain water from willing water purveyors. However, uncertainty regarding the nature and extent of some senior water claims combine with indeterminate interstate river management to cast a cloud over water resource allocation and management. Quantitative and qualitative water requirements associated with Endangered Species protection also stand as barriers to significant water development, and complex water quality regulations will apply to unconventional fuel development. Legal and political decisions can give shape to an indeterminate landscape. Settlement of Northern Ute reserved rights claims would help clarify the worth of existing water rights and viability of alternative sources of supply. Interstate apportionment of the White River would go a long way towards resolving water availability in downstream Utah. And energy policy clarification will help determine the role oil shale and oil sands will play in our nation’s future.

Suitability of a South African silica sand for three-dimensional printing of foundry moulds and cores

Directory of Open Access Journals (Sweden)

Nyembwe, Kasongo

2016-11-01

Full Text Available Applications of three-dimensional printing (3DP to metal casting include, among other things, the direct manufacturing of foundry moulds and cores in refractory materials such as silica sand. The main properties of silica sand that are essentially related to the traditional moulding and core-making processes are: size distribution, clay content, pH, acid demand, and refractoriness. The silica sand used for 3DP must also be appropriately selected for the layer-based manufacturing process involved in 3DP. Properties such as grain size distribution, grain surface morphology, angularity, flowability, and recoating abilities have a particular importance when determining sand suitability. Because of these extra requirements, only a limited range of available foundry silica sands can be used for 3DP processes. The latter situation explains the scarcity and high cost of suitable silica sands, thus contributing to the relatively high operational costs of the 3DP processes for the production of sand moulds and cores. This research paper investigates the suitability of a locally-available silica sand for use in a Voxeljet VX1000 3DP machine. The local silica sand was assessed and compared with an imported silica sand recommended by the manufacturer of 3DP equipment in terms of foundry characteristics and recoating behaviour. The study shows that, despite the differences between the characteristics of the two silica sands, the local sand could be considered a suitable alternative to imported sand for rapid sand casting applications.

Bearing capacity of Skirt circular footing on sand

Directory of Open Access Journals (Sweden)

Amr Z. EL Wakil

2013-09-01

Full Text Available Skirts are used to improve the bearing capacity of shallow footings on sandy soil by constraining the soil beneath and containing the plastic flow of soil. They are used as an alternative to deep foundations in soils with low strength at the surface. As there has been available little work studying the performance of skirted foundation, we are performing eighteen laboratory experiments on circular steel footings of different diameters and different skirt lengths. The aim of these experiments is to shed some lights on the effects of skirts on the bearing capacity of shallow footings. The effects of skirt length and the relative density of sand on the ultimate load attained were investigated. From the accomplished laboratory tests, it was found that skirts improve appreciably the sustainability of shallow footings to applied load as they increase the ultimate load of shallow footings by some up to 6.25 times for the current study conditions and variables. The performance of skirted footing depends upon the relative density of sand and on the skirt length to footing diameter ratio. Skirts are more beneficial in case of footings on loose sand than in case of medium and dense sand.

Effective Laboratory Method of Chromite Content Estimation in Reclaimed Sands

Directory of Open Access Journals (Sweden)

Ignaszak Z.

2016-09-01

Full Text Available The paper presents an original method of measuring the actual chromite content in the circulating moulding sand of foundry. This type of material is applied for production of moulds. This is the case of foundry which most frequently perform heavy casting in which for the construction of chemical hardening mould is used, both the quartz sand and chromite sand. After the dry reclamation of used moulding sand, both types of sands are mixed in various ratios resulting that in reclaimed sand silos, the layers of varying content of chromite in mixture are observed. For chromite recuperation from the circulating moulding sand there are applied the appropriate installations equipped with separate elements generating locally strong magnetic field. The knowledge of the current ratio of chromite and quartz sand allows to optimize the settings of installation and control of the separation efficiency. The arduous and time-consuming method of determining the content of chromite using bromoform liquid requires operational powers and precautions during using this toxic liquid. It was developed and tested the new, uncomplicated gravimetric laboratory method using powerful permanent magnets (neodymium. The method is used in the production conditions of casting for current inspection of chromite quantity in used sand in reclamation plant.

Intermontane eolian sand sheet development, Upper Tulum Valley, central-western Argentina

Directory of Open Access Journals (Sweden)

Patrick Francisco Fuhr Dal' Bó

Full Text Available ABSTRACTThe intermontane Upper Tulum eolian sand sheet covers an area of ca. 125 km² at north of the San Juan Province, central-western Argentina. The sand sheet is currently an aggrading system where vegetation cover, surface cementation and periodic flooding withhold the development of dunes with slipfaces. The sand sheet surface is divided into three parts according to the distribution of sedimentary features, which reflects the variation in sediment budget, water table level and periodic flooding. The central sand sheet part is the main area of eolian deposition and is largely stabilized by vegetation. The sedimentary succession is 4 m thick and records the vertical interbedding of eolian and subaqueous deposits, which have been deposited for at least 3.6 ky with sedimentation rates of 86.1 cm/ky. The construction of the sand sheet is associated with deflation of the sand-graded debris sourced by San Juan alluvial fan, which is available mainly in drier fall-winter months where water table is lower and wind speeds are periodically above the threshold velocity for sand transport. The accumulation of sedimentary bodies occurs in a stabilized eolian system where vegetation cover, thin mud veneers and surface cementation are the main agents in promoting accumulation. The preservation of the sand sheet accumulations is enabled by the progressive creation of the accommodation space in a tectonically active basin and the continuous burial of geological bodies favored by high rates of sedimentation.

Strength Characteristics of Quarry Dust in Replacement of Sand

Science.gov (United States)

Shyam Prakash, K.; Hanumantha Rao, Ch, Dr

2017-08-01

The replacement of natural fine aggregate by using quarry dust leads to consumption of generated quarry dust, the requirement of land fill area can be reduced and solves the natural sand scarcity problem. The sand availability as a fine aggregate at low cost which needs the reason to search as a alternative material. Even it causes saddle to dump the crusher dust at one place which causes environmental pollution. The chemical analysis, specific gravity, sieve analysis and compressive strength is identified for various percentage and grades of concrete by replacement of sand with quarry dust.

Used Furan Sand Reclamation in REGMAS Vibratory Unit

Directory of Open Access Journals (Sweden)

Dańko J.

2015-09-01

Full Text Available The paper, especially dealt with problems of reclamation of used furan sand, carried out in new, vibratory sand reclamation unit REGMAS developed by researches from AGH-University of Science and Technology, Faculty of Foundry Engineering in Cracow (Poland. Functional characteristics of reclamation unit as well as the results of reclamation of used sand with furfuryl resin are discussed in the paper. The quality of reclaim was tested by means of the LOI and pH value, dust content in the reclaim and at least by the the quality of the castings produced in moulds prepared with the use of reclaimed matrix.

Dynamic shear stiffness and damping ratio of marine calcareous and siliceous sands

Science.gov (United States)

Javdanian, Hamed; Jafarian, Yaser

2018-03-01

Shear stiffness and damping ratio of two marine calcareous and siliceous sands were evaluated through an experimental program. Resonant column and cyclic triaxial experiments were conducted to measure the dynamic properties of the sands in small and large shear strain amplitudes. The tests were conducted under various initial stress-density conditions. The influence of effective confining pressure on the dynamic properties of the sands was assessed and compared in a preceding paper. It was shown that the calcareous sand has higher shear stiffness and lower damping ratio in comparison to the siliceous sand. In this note, the results are presented in more details and the dynamic behavior curves of the studied sands are compared with some available models, mostly developed based on the laboratory data of siliceous sands. This comparative study reveals that the previous models predict the dynamic properties of the calcareous sand in less precision than those of the siliceous sand.

Effect of River Indus Sand on Concrete Tensile Strength

Directory of Open Access Journals (Sweden)

M. T. Lakhiar

2018-04-01

Full Text Available In the development of Pakistan construction industry, the utilization of River Indus sand in concrete as fine aggregate has expanded tremendously. The aim of this research is to study the effect of Indus River sand on the tensile strength of various grades of concrete when it is utilized as fine aggregate. Concrete Samples of M15, M20 and M25 grade concrete were cured for 7, 14, 21 and 28 days. Based on the results, it is found that concrete became less workable when Indus river sand was utilized. It is recorded that tensile strength of concrete is decreased from 5% up to 20% in comparison with hill sand. The results were derived from various concrete grades.

Liquefaction resistance of calcareous sands

International Nuclear Information System (INIS)

Sandoval Vallejo, Eimar

2012-01-01

Calcareous sands are unique in terms of their origin, mineralogy, shape, fragility and intra particle porosity. This article presents results from an experimental program carried out to study the liquefaction resistance of a calcareous sand retrieved from Cabo Rojo at Puerto Rico. The experimental program included mineralogical characterization, index properties, and undrained cyclic triaxial tests on isotropically consolidated reconstituted samples. Due to the large variation in the calcareous sand properties, results are compared with previous researches carried out on other calcareous sands around the world. Results showed a wide range in the liquefaction resistance of the studied calcareous sands. Cabo Rojo sand experienced greater liquefaction resistance than most of the calcareous sands used for comparison. Important differences in the excess pore pressure generation characteristics were also found.

Exposure to Phlebotomus argentipes (Diptera, Psychodidae, Phlebotominae sand flies in rural areas of Bihar, India: the role of housing conditions.

Directory of Open Access Journals (Sweden)

Paritosh Malaviya

Full Text Available Visceral Leishmaniasis (VL is a vector-borne infectious disease, caused by the protozoan Leishmania donovani, which is transmitted by phlebotomine sand flies. In an earlier study in Bihar, India, we found an association between incidence of VL and housing conditions. In the current study we investigated the influence of housing structure and conditions in and around the house on the indoor abundance of Phlebotomus argentipes, the vector of VL in this area.In each of 50 study villages in Muzaffarpur district, we randomly selected 10 houses. Light traps were installed in each house for one night during three annual peaks of sand fly density over two successive years. Sand flies captured were morphologically identified and segregated by species, sex and feeding status. Data on housing conditions and socio-economic status were also collected. We fitted a linear mixed-effects regression model with log-transformed P. argentipes counts as outcome variable and village as random effect.P. argentipes was found in all but four of the 500 households. There was considerable variability between the years and the seasons. On bivariate analysis, housing structure, dampness of the floor, keeping animals inside, presence of animal dung around the house, and socio-economic status were all significantly associated with sand fly density. Highest sand fly densities were observed in thatched houses. In the multivariate model only the housing structure and socio-economic status remained significant.Better housing conditions are associated with lower sand fly densities, independent of other socio-economic conditions. However, in this area in Bihar even in the better-built houses sand flies are present.

The Holocene evolution of the beach and inland aeolian sand of the north-central Mediterranean coast of Israel

Science.gov (United States)

Roskin, Joel; Sivan, Dorit; Bookman, Revital; Shteinberg, Gilad

2015-04-01

Israel's coastal geomorphology, situated within a Mediterranean climate zone, is characterized by parallel Pleistocene aeolianite ridges, coastal cliffs of aeolianite, and sandy beaches. Lobe-like fields of predominantly stable transverse and parabolic quartz sand dunes protrude 2-7 km inland from the current Mediterranean Sea coastline. However, their migration and accumulation history is still not well-defined. This study focuses on the Holocene appearance, chronology and drivers of beach sand deposition and inland aeolian sand transport along the Caesarea-Hadera dunefield in the north-central coastal plain of Israel. In order to achieve these goals, a detailed field survey and sampling campaign was carried out along a west-east and southwest-northeast transect, loyal to the advancement orientations of the currently stable dunes and directions of dominant sand transporting winds. Beach sand, a foredune, a linear dune, and interdunes of parabolic and transverse dunes were sampled down to their aeolianite or red loam (locally named hamra) palaeosol substrate by drilling and analyzing exposed sections. The sampled sediments were sedimentologically analyzed and twenty-five were dated by optically stimulated luminescence (OSL). The results indicate that beach sand started to accumulate rapidly around 6 ka probably in response to global sea level stabilization. Until around 4 ka, thin sand sheets encroached 2-3 km inland. Sand ages in the range of 1.2-1.1 ka (8th-9th century CE -- Early Moslem period) were found throughout the study area, suggesting a major mobilization of sand, followed by stabilization around 0.6 ka and pedogenesis. By 1.2 ka, the sands had reached their current extent of 5-7 km inland, suggesting transport in a southwest-northeast orientation similar to the advancement orientation of the current transverse and parabolic dunes. The particle-size distributions of the fine to medium-sized aeolian sand showed minor variation linked to inland transport

Design of Screens for Sand Control of Wells

Directory of Open Access Journals (Sweden)

Ján Pinka

2006-04-01

Full Text Available Drilling, completion, production, and reservoir engineers, supervisors, foremen, superintendents, service company personnel, technologists and anyone involved with recommending, selecting, designing or on-site performance of well completions or workovers where sand production is, or may become, a serious problem will benefit from this course. Less sand influx can be expected in a horizontal well than in a vertical well. If horizontal holes in weak formation sands can be successfully gravel packed, the result could be significantly higher well productivity than with a liner, screen or pre-packed screen alone. The article covers innovative screens for sand control used in oil and gas industry from the world leaders in total completion. The type of screen (wire wrapped, reinforced, pre-packed, ect. should also be chosen with due consideration to running-in condition (curve radius, compression when the screens are pushed along the drain hole, etc..

Identification of discontinuous sand pulses on the bed of the Colorado River in Grand Canyon

Science.gov (United States)

Mueller, E. R.; Grams, P. E.; Buscombe, D.; Topping, D. J.

2017-12-01

Decades of research on alluvial sandbars and sand transport on the Colorado River in Grand Canyon has contributed to in-depth understanding of the sand budget and lead to management actions designed to rebuild eroded sandbars. However, some basic, but difficult to address, questions about the processes and rates of sand movement through the system still limit our ability to predict geomorphic responses. The coarse fraction of the bed is heterogeneous and varies among boulders, cobble, gravel, and bedrock. Sand covers these substrates in patches of variable size and thickness, fills interstices to varying degrees, and forms mixed sand/coarse bed configurations such as linear stripes. Understanding the locations of sand accumulation, the quantities of sand contained in those locations, and the processes by which sand is exchanged among depositional locations is needed to predict the morphological response of sandbars to management actions, such as the controlled flood releases, and to predict whether sandbars are likely to increase or decrease in size over long (i.e. decadal) time periods. Here, we present evidence for the downstream translation of the sand component of tributary sediment inputs as discontinuous sand pulses. The silt and clay (mud) fraction of sediment introduced episodically by seasonal floods from tributary streams is transported entirely in suspension and moves through the 400 km series of canyons in a few days. The sand fraction of this sediment, which is transported on the bed and in suspension, moves downstream in sand pulses that we estimate range in length from a few km to tens of km. Owing to the complex geomorphic organization, the sand pulses are not detectable as coherent bed features; each individual sand pulse is comprised of many isolated storage locations, separated by rapids and riffles where sand cover is sparse. The presence of the sand pulses is inferred by the existence of alternating segments of sand accumulation and depletion

Diffusive transport of strontium-85 in sand-bentonite mixtures

International Nuclear Information System (INIS)

Gillham, R.W.; Robin, M.J.L.; Dytynyshyn, D.J.

1983-06-01

Diffusion experiments have been used to determine the transport of 85 Sr in sand-bentonite mixtures. The diffusion experiments were performed on one natural soil (Chalk River sand) and on seven mixtures of bentonite and silica sand, containing from 0 percent to 100 percent bentonite. Two non-reactive solutes ( 36 Cl and 3 H) and one reactive solute ( 85 Sr) were used in the study. The experiments with non-reactive solutes yielded estimates of tortuosity factors. Retardation factors were obtained from experimental porosities, experimental bulk densities, and from batch distribution coefficients (Ksub(d)). These Ksub(d) values are a simple way of describing the solute/medium reaction, and are based on the assumption that the cation-exchange reaction may be described by a linear adsorption isotherm passing through the origin. The results demonstrate that, for practical purposes and for our experimental conditions, the use of the distribution coefficient provides a convenient means of calculating the effective diffusion coefficient for 85 Sr. The porosity and bulk density were also found to have a considerable influence on the effective diffusion coefficient, through the retardation factor. Mixtures containing 5-10 percent bentonite were found to be more effective in retarding 85 Sr than either sand alone, or mixtures containing more bentonite. In the soils of higher bentonite content, the effect of increased cation-exchange capacity was balanced by a decreasing ratio of bulk density to porosity

Interpretation of the stiffness and permeability of Sand-Kaolin mixtures in the framework of homogenization

Directory of Open Access Journals (Sweden)

Claude Boutin

2010-03-01

Full Text Available This study deals with the behaviour of mixtures of sand and saturated kaolin paste considered as composite materials made of permeable and deformable (with non-linear behaviour matrix (the kaolin paste with rigid and impervious inclusions (the sand grains. Oedometric and permeability tests conducted on such mixtures highlight the key role of the state of the clay paste, and show the existence of a threshold of sand grain concentration above which a structuring effect influences both modulus and permeability. At the light of these experiments, the usual and tangent homogenization process (with simplifying assumptions to make the problem manageable has been applied to estimate the mixture permeability and tangent compressibility. Qualitative and quantitative comparisons with experimental data point out the domain of interest and the limitations of such approaches.O estudo lida com o comportamento de misturas compostas por areia e uma pasta de caulinita considerada um material composto feito de uma matriz (caulinita permeável e deformável (com comportamento não-linear com inclusões rígidas e impermeáveis (grãos de areia. Testes de permeabilidade e odométricos conduzidos nestas misturas enfatizam o papel chave de estado da pasta argilosa e mostram a existência de uma concentração crítica de grãos de areia com efeito estruturante que influencia o módulo e a permeabilidade. Sob a luz destes experimentos o processo de homogeneização usual e tangente (com hipóteses simplificadoras para tornar o problema tratável foi aplicado para estimar a permeabilidade da mistura e a compressibilidade tangente. Comparações qualitativas e quantitativas com dados experimentais apontam o domínio de interesse bem como a limitação destas abordagens.

Sand control systems used in completing wells

Directory of Open Access Journals (Sweden)

Gabriel Wittenberger

2005-12-01

Full Text Available Expandable Tubular Technology is transforming the face of well completion and construction. This technology provides: a substantially higher hydrocarbon production rates from the reservoir, a reduced well drilling and construction costs, new possibilities for previously unreachable or uneconomic reservoirs, and step a change towards the single diameter well. ESS (Expandable Sand Screen has an unrivalled performance worldwide for delivering a reliable sand control in a wide range of applications. Well costs typically cut by over 20 %, and the productivity increases up to 70 %.

The Rheology of Acoustically Fluidized Sand

Science.gov (United States)

Conrad, J. W.; Melosh, J.

2013-12-01

strain rate and stress is linear. In our experiments we found that the shear strain rate is proportional to shear stress raised to the powers 5.9 and 8.4 at frequencies of 8.5 kHz and 7.4 kHz and increasing amplitude of vibration, respectively. This demonstrates that vibrated sand behaves as a strongly nonlinear pseudo-plastic material that, like glacier ice, can also be approximated as a Bingham material with a rate-dependent yield stress. The flow of acoustically fluidized granular materials provides a reasonable explanation of crater collapse, long runout landslides, and other events involving large masses of granular material.

Experimental and numerical study on thermal conductivity of partially saturated unconsolidated sands

Science.gov (United States)

Lee, Youngmin; Keehm, Youngseuk; Kim, Seong-Kyun; Shin, Sang Ho

2016-04-01

A class of problems in heat flow applications requires an understanding of how water saturation affects thermal conductivity in the shallow subsurface. We conducted a series of experiments using a sand box to evaluate thermal conductivity (TC) of partially saturated unconsolidated sands under varying water saturation (Sw). We first saturated sands fully with water and varied water saturation by drainage through the bottom of the sand box. Five water-content sensors were integrated vertically into the sand box to monitor water saturation changes and a needle probe was embedded to measure thermal conductivity of partially saturated sands. The experimental result showed that thermal conductivity decreases from 2.5 W/mK for fully saturated sands to 0.7 W/mK when water saturation is 5%. We found that the decreasing trend is quite non-linear: highly sensitive at very high and low water saturations. However, the boundary effects on the top and the bottom of the sand box seemed to be responsible for this high nonlinearity. We also found that the determination of water saturation is quite important: the saturation by averaging values from all five sensors and that from the sensor at the center position, showed quite different trends in the TC-Sw domain. In parallel, we conducted a pore-scale numerical modeling, which consists of the steady-state two-phase Lattice-Boltzmann simulator and FEM thermal conduction simulator on digital pore geometry of sand aggregation. The simulation results showed a monotonous decreasing trend, and are reasonably well matched with experimental data when using average water saturations. We concluded that thermal conductivity would decrease smoothly as water saturation decreases if we can exclude boundary effects. However, in dynamic conditions, i.e. imbibition or drainage, the thermal conductivity might show hysteresis, which can be investigated with pore-scale numerical modeling with unsteady-state two-phase flow simulators in our future work.

Casting Ductile Iron in Layer Moulds Made from Ecological Sands

Directory of Open Access Journals (Sweden)

M. Rączka

2012-09-01

Full Text Available The article contains the results of tests performed under the target project in Hardtop Foundry Charsznica.The objective of the tests and studies was to develop a technology of making high-quality ductile iron castings, combined witheffective means of environmental protection. The studies presented in this article related to castings weighing from 1 to 300 kg made from ductile iron of grades 400-15 and 500-7, using two-layer moulds, where the facing and core sand was the sand with an alkaline organic binder, while backing sand was the sand with an inorganic geopolymer binder.A simplified method of sand reclamation was applied with possible reuse of the reclaim as an addition to the backing sand. The castiron spheroidising treatment and inoculation were selected taking into account the specific conditions of Hardtop Foundry. A pilot batch of castings was made, testing the gating and feeding systems and using exothermic sleeves on risers. The study confirmed the validity of the adopted concept of making ductile iron castings in layer moulds, while maintaining the content of sand with an organic binder at a level of maximum 15%.

Parameters and mechanisms in the mechanical upgrading of Athabasca oil sands by a cold water process

Energy Technology Data Exchange (ETDEWEB)

Grant, G B

1977-01-01

The efficiency of sand rejection in the cold water mechanical upgrading of Athabasca oil sands has been studied in the operation of rotary contactors of 8.9 cm and 19.0 cm internal diameter, fitted with lifters. Duration of operation, rate of rotation, linear velocity of lifters, temperature, water to oil sands ratio, depth of charge to lifter height ratio, and internal diameter of the contactor have been identified as important parameters. Surfactant addition and presoaking of the feed had negligible effects on the process. A model has been proposed that accounts for the variation of extraction efficiency as a function of duration of operation, the data showing that both the equilibrium extraction efficiency and the rate constant were greater in the large contactor than the small contactor for equal rates of rotation, except when centrifuging occurred in the large contactor. Sand rejection was promoted by lifter-sand and contactor wall-sand impacts and by the action of shear fields within vortices created by the lifter. The impacts occurred for all loading conditions but the latter mechanism only contributed to the sand rejection process for depth-of-charge to lifter height ratios of one or greater. In addition, the contribution of shear fields was only significant for large water to oil sands ratios. Finally, the sand rejection process was affected significantly by variations in temperature. 37 refs., 34 figs., 11 tabs., 4 illus.

Rheological Characterization of Green Sand Flow

DEFF Research Database (Denmark)

Jabbaribehnam, Mirmasoud; Spangenberg, Jon; Hovad, Emil

2016-01-01

The main aim of this paper is to characterize experimentally the flow behaviour of the green sand that is used for casting of sand moulds. After the sand casting process is performed, the sand moulds are used for metal castings. The rheological properties of the green sand is important to quantif...

Tailings dewatering in the oil sands

Energy Technology Data Exchange (ETDEWEB)

Longo, S.; Labelle, M. [Golder Paste Technology, Sudbury, ON (Canada); Wislesky, I. [Golder Associates Ltd., Calgary, AB (Canada)

2010-07-01

Alberta's Directive 074 was established to reduce fluid tailings produced during oil sands extraction processes. This PowerPoint presentation examined some of the dewatering strategies available for oil sands operators and provided recommendations for implementing a dewatering plan. Sites must be evaluated in order to determine their chemistry, mineralogy, and the total quantity of material to be handled. The availability of potential additives must also be considered. Process technologies must be selected in relation to the operator's depositional strategy. Each site will require its own unique dewatering and depositional strategy. Dewatering technologies include thickening; in-line flocculation; centrifuge; co-mingling; and various new technologies such as electro-osmosis. Laboratory testing programs include index tests, primary stream thickening, and mini-pilot plant testing. The performance of various testing formats was evaluated. Thickening and depositional techniques were reviewed. tabs., figs.

Study on the Permeability Characteristics of Polyurethane Soil Stabilizer Reinforced Sand

Directory of Open Access Journals (Sweden)

Jin Liu

2017-01-01

Full Text Available A polymer material of polyurethane soil stabilizer (PSS is used to reinforce the sand. To understand the permeability characteristics of PSS reinforced sand, a series of reinforcement layer form test, single-hole permeability test, and porous permeability test of sand reinforced with PSS have been performed. Reinforcement mechanism is discussed with scanning electron microscope images. The results indicated that the permeability resistance of sand reinforced with polyurethane soil stabilizer is improved through the formation of reinforcement layer on the sand surface. The thickness and complete degree of the reinforcement layer increase with the increasing of curing time and PSS concentration. The water flow rate decreases with the increasing of curing time or PSS concentration. The permeability coefficient decreases with the increasing of curing time and PSS concentration and increases with the increasing of depth in specimen. PSS fills up the voids of sand and adsorbs on the surface of sand particle to reduce or block the flowing channels of water to improve the permeability resistance of sand. The results can be applied as the reference for chemical reinforcement sandy soil engineering, especially for surface protection of embankment, slope, and landfill.

LAND COVER DYNAMICS OF OLESHKY SANDS: TIME-SERIES ANALYSIS 1987-2017

Directory of Open Access Journals (Sweden)

V. Bogdanets

2017-11-01

Full Text Available Oleshky Sands is the largest expanse of sand in Ukraine and the second in Europe. In the beginning of XX century sands moving outside of arenas was almost stopped by planting trees (Pinus nigra ssp. pallasian and Pinus sylvestris L., and the territory had different use during the years. A 30-year (1987-2017 time series of Landsat imagery obtained via USGS geoservice was used to reveal land cover dynamics of deserted landscapes of Oleshky sands using QGIS software. Heavy sand storms can impact nearby settlements and expose harmful effect on local industry and quality of life of local communities. Forest fire is another dangerous factor for protective forest plantations during last years. Our estimation shows that sandy areas increase during 2000-2017; generally, conservation measures had constant effect despite afforestation of last years. The preventive effect of forest on sands moving at Oleshky sands can be characterized as stable in case of constant care about the forest plantation and proper documentation on land use and ownership.

The Alberta oil sands story

Energy Technology Data Exchange (ETDEWEB)

1974-01-01

This report serves as a detailed introduction to the Alberta oil sands and their development. It includes a description of the oil sands deposits, an outline of crude bitumen recovery and upgrading processes, the role of Alberta Energy Company in oil sands development, environmental aspects, manpower requirements for oil sands development, research needs, and further oil sands projects. Presently proven recoverable reserves in the oil sands amount to 26.5 billion bbl of synthetic crude. Production from the Syncrude plant (125,000 bbl/d capacity) is expected to begin in 1977, followed by a Shell Canada operation around 1980. The provincial government will participate in the oil sand industry through its joint venture participation in Syncrude and its 50% share in Alberta Energy Company; the latter company participates in related aspects of the Syncrude project, such as pipelines. The result of Alberta's participation in the industry will mean that, directly or indirectly, the province will realize 60% of the total profits. The job creation potential of oil sands projects is estimated to be extensive, with a direct and indirect work force supported by oil sands activities possibly reaching 180,000 persons by the year 2000. Research needs have been identified, particularly in the area of in-situ thermal recovery technology, and the creation of the Alberta Oil Sands Technology and Research Authority has been authorized in order to meet these needs. Although current reserves are sufficient to support 20-30 synthetic crude plants, a number of factors will limit expansion of the industry. 8 figs., 5 tabs.

A comparison of publicly available linear MRI stereotaxic registration techniques.

Science.gov (United States)

Dadar, Mahsa; Fonov, Vladimir S; Collins, D Louis

2018-07-01

Linear registration to a standard space is one of the major steps in processing and analyzing magnetic resonance images (MRIs) of the brain. Here we present an overview of linear stereotaxic MRI registration and compare the performance of 5 publicly available and extensively used linear registration techniques in medical image analysis. A set of 9693 T1-weighted MR images were obtained for testing from 4 datasets: ADNI, PREVENT-AD, PPMI, and HCP, two of which have multi-center and multi-scanner data and three of which have longitudinal data. Each individual native image was linearly registered to the MNI ICBM152 average template using five versions of MRITOTAL from MINC tools, FLIRT from FSL, two versions of Elastix, spm_affreg from SPM, and ANTs linear registration techniques. Quality control (QC) images were generated from the registered volumes and viewed by an expert rater to assess the quality of the registrations. The QC image contained 60 sub-images (20 of each of axial, sagittal, and coronal views at different levels throughout the brain) overlaid with contours of the ICBM152 template, enabling the expert rater to label the registration as acceptable or unacceptable. The performance of the registration techniques was then compared across different datasets. In addition, the effect of image noise, intensity non-uniformity, age, head size, and atrophy on the performance of the techniques was investigated by comparing differences between age, scaling factor, ventricle volume, brain volume, and white matter hyperintensity (WMH) volumes between passed and failed cases for each method. The average registration failure rate among all datasets was 27.41%, 27.14%, 12.74%, 13.03%, 0.44% for the five versions of MRITOTAL techniques, 8.87% for ANTs, 11.11% for FSL, 12.35% for Elastix Affine, 24.40% for Elastix Similarity, and 30.66% for SPM. There were significant effects of signal to noise ratio, image intensity non-uniformity estimates, as well as age, head size, and

Improving the geotechnical behavior of sand through cohesive admixtures

Directory of Open Access Journals (Sweden)

Mohie eldin Mohamed Afify Elmashad

2018-04-01

Full Text Available Irrigation projects in Egypt have been facing tremendous challenges, mostly is the scarcity of irrigation water. The current research presents the effect of different cohesive admixture on the conductivity of siliceous sand in general and its other geotechnical properties. Two different types of conventional swelling clay from (Toshka, 6th of October as well as bentonite were used to construct the irrigation canals and embankment. The results indicated that increase in the plasticity properties of the treated soil also decrease the permeability and infiltration. Moreover, the dry density of 2.08 t/m3 was obtained from sand and 20% 6th of October mixture, also the CBR of 31.20% were obtained from sand and 8% 6th of October mixture. Increasing the bentonite ratio increases the cohesion and decreasing the permeability. The swelling ratios of sand 6th of October Clay mixture is equal to 0.28%, and the fictitious stress at which the swelling ratio is nil, is equal to 16 kPa. Keywords: Sand, Swelling clay, Bentonite, Compaction test, Consolidation test, Triaxial test

PCE and BNS admixture adsorption in sands with different composition and particle size distribution

Directory of Open Access Journals (Sweden)

M. M. Alonso

2017-02-01

Full Text Available The choice of a superplasticiser (SP for concrete is of great complexity, as it is well known that properties of the end product are related to admixture and its compatibility with concrete components. Very few studies have been conducted on the compatibility between SPs and the sand of mortars and concretes, however. Practical experience has shown that sand fineness and mineralogical composition affect water demand and admixture consumption. Clay-containing sand has been found also to adsorb SPs, reducing the amount available in solution for adsorption by the cement. This study analysed the isotherms for PCE and BNS superplasticiser adsorption on four sands with different fineness and compositions commonly used to prepare mortars and concretes. BNS-based SP did not adsorb on sands, while PCE-based admixtures exhibited variable adsorption depending on different factors. The adsorption curves obtained revealed that the higher the sand fineness, the finer the particle size distribution and the higher the clay material, the greater was PCE admixture adsorption/ consumption.

Opportunities for CANDU for the Alberta oil sands

International Nuclear Information System (INIS)

Hopwood, J.M.; Bock, D.; Miller, A.; Kuran, S.; Keil, H.; Fiorino, L.; Hau, K.; Zhou, X.; Dunbar, R.B.

2003-01-01

The Alberta oil sands bitumen deposits comprise of one of the largest sources hydrocarbon in the world, and have emerged as the fastest growing, soon to be dominant, source of crude oil in Canada. The oil industry has made great strides in improving the effectiveness of gathering this resource. In particular, alternatives to open-pit mining have been developed which enable in-site recovery of underground deposits with a minimum of environmental disruption. The main challenge that remains is the large quantity of energy needed in the process of extracting the oil and upgrading it to commercial levels. For a typical in-situ extraction project, about 18% of the energy content of the oil produced is used up in the extraction process, while a further 5% is used in generating hydrogen to upgrade the bitumen to synthetic crude oil. Looking ahead, even as improvements in energy use efficiency, (and hydrocarbon use efficiency) counterbalance the increases in hydrocarbon demand from economic growth (particularly in the developing world), Canada and Alberta recognize that the oil sands resource will be needed, and both support the development of this resource in an environmentally responsible way. The large energy requirement for the oil sands extraction process represents a challenge with regard to both environmental impact and security of supply. The use of natural gas, the current energy supply, has impacts in terms of air quality (via NOX and other emissions) and also represents a large greenhouse gas emissions component. As the oil sands industry expands, the availability of natural gas also becomes a concern, as does price and price stability. With this background, the opportunity for nuclear reactors to provide an economical, reliable, virtually zero-emission source of energy for the oil sands becomes very important. Over the last few years, developments in oil sands extraction technology, and developments in CANDU technology through the Advanced CANDU Reactor, (ACR

Deposition behaviour of model biofuel ash in mixtures with quartz sand. Part 1: Experimental data

Energy Technology Data Exchange (ETDEWEB)

Mischa Theis; Christian Mueller; Bengt-Johan Skrifvars; Mikko Hupa; Honghi Tran [Aabo Akademi Process Chemistry Centre, Aabo (Finland). Combustion and Materials Chemistry

2006-10-15

Model biofuel ash of well-defined size and melting properties was fed into an entrained flow reactor (EFR) to simulate the deposition behaviour of commercially applied biofuel mixtures in large-scale boilers. The aim was to obtain consistent experimental data that can be used for validation of computational fluid dynamics (CFD)-based deposition models. The results showed that while up to 80 wt% of the feed was lost to the EFR wall, the composition of the model ash particles collected at the reactor exit did not change. When model ashes were fed into the reactor individually, the ash particles were found to be sticky when they contained more than 15 wt% molten phase. When model ashes were fed in mixtures with silica sand, it was found that only a small amount of sand particles was captured in the deposits; the majority rebounded upon impact. The presence of sand in the feed mixture reduced the deposit buildup by more than could be expected from linear interpolation between the model ash and the sand. The results suggested that sand addition to model ash may prevent deposit buildup through erosion. 22 refs., 6 figs., 3 tabs.

Compressive behavior of fine sand.

Energy Technology Data Exchange (ETDEWEB)

Martin, Bradley E. (Air Force Research Laboratory, Eglin, FL); Kabir, Md. E. (Purdue University, West Lafayette, IN); Song, Bo; Chen, Wayne (Purdue University, West Lafayette, IN)

2010-04-01

The compressive mechanical response of fine sand is experimentally investigated. The strain rate, initial density, stress state, and moisture level are systematically varied. A Kolsky bar was modified to obtain uniaxial and triaxial compressive response at high strain rates. A controlled loading pulse allows the specimen to acquire stress equilibrium and constant strain-rates. The results show that the compressive response of the fine sand is not sensitive to strain rate under the loading conditions in this study, but significantly dependent on the moisture content, initial density and lateral confinement. Partially saturated sand is more compliant than dry sand. Similar trends were reported in the quasi-static regime for experiments conducted at comparable specimen conditions. The sand becomes stiffer as initial density and/or confinement pressure increases. The sand particle size become smaller after hydrostatic pressure and further smaller after dynamic axial loading.

Estimation of Sand Production Rate Using Geomechanical and Hydromechanical Models

Directory of Open Access Journals (Sweden)

Son Tung Pham

2017-01-01

Full Text Available This paper aims to develop a numerical model that can be used in sand control during production phase of an oil and gas well. The model is able to predict not only the onset of sand production using critical bottom hole pressure inferred from geomechanical modelling, but also the mass of sand produced versus time as well as the change of porosity versus space and time using hydromechanical modelling. A detailed workflow of the modelling was presented with each step of calculations. The empirical parameters were calibrated using laboratory data. Then the modelling was applied in a case study of an oilfield in Cuu Long basin. In addition, a sensitivity study of the effect of drawdown pressure was presented in this paper. Moreover, a comparison between results of different hydromechanical models was also addressed. The outcome of this paper demonstrated the possibility of modelling the sand production mass in real cases, opening a new approach in sand control in petroleum industry.

Reclamation of alkaline spent moulding sands of organic and inorganic type and their mixtures

Directory of Open Access Journals (Sweden)

R. Dańko

2011-10-01

Full Text Available Introduction of modern moulding sands with organic and inorganic binders requires the reclamation treatments in order to be able to reuse the matrices of spent sands. The spent sands, depending on the applied binding agent, are characterised by various abilities of the matrix reclamation. The results of investigations of the reclamation of spent moulding sands with the Rudal binder and spent sands with the Rezolit binder in the system of uniform sands and of mixed ones, are presented in the paper. Investigations were performed by means of the special experimental stands designed and built in the AGH University of Science and Technology, AGH, in Krakow.

A Life Cycle Assessment of Silica Sand: Comparing the Beneficiation Processes

Directory of Open Access Journals (Sweden)

Anamarija Grbeš

2015-12-01

Full Text Available Silica sand or quartz sand is a mineral resource with a wide variety of application; glass industry, construction and foundry are the most common examples thereof. The Republic of Croatia has reserves of 40 million tons of silica sand and a long tradition of surface mining and processing. The average annual production of raw silica sand in Croatia in the period from 2006 to 2011 amounted to 150 thousand tons. This paper presents cradle to gate LCA results of three different types of beneficiation techniques: electrostatic separation; flotation; gravity concentration. The aim of this research is to identify and quantify the environmental impacts of the silica sand production, to learn the range of the impacts for different processing methods, as well as to identify the major contributors and focus for further process design development.

Physical, mechanical and thermal properties of Crushed Sand Concrete containing Rubber Waste

Directory of Open Access Journals (Sweden)

Mohamed Guendouz

2018-01-01

Full Text Available Over the past twenty years, the rubber wastes are an important part of municipal solid waste. This work focuses on the recycling of rubber waste, specifically rubber waste of used shoes discharged into the nature and added in the mass of crushed sand concrete with percentage (10%, 20%, 30% and 40%. The physical (workability, fresh density, mechanical (compressive and flexural strength and thermal (thermal conductivity of different crushed sand concrete made are analyzed and compared to the respective controls. The use of rubber waste in crushed sand concrete contributes to reduce the bulk density and performance of sand concrete. Nevertheless, the use of rubber aggregate leads to a significant reduction in thermal conductivity, which improves the thermal insulation of crushed sand concrete.

AE Test of Calcareous Sands with Particle Rushing

Directory of Open Access Journals (Sweden)

Tan Fengyi

2017-08-01

Full Text Available The particle of calcareous sands was forced to crush, then the energy from the crushing was released by the form of sound waves. Therefore the AE technique was used to detect the calcareous sands AE signal when it crushed. by to study the AE characteristics, the mechanics of calcareous sands was studied. Study showed that: (1 there was the AE activities on the low confining pressure condition at the beginnig of test, (2 there was more and more AE activities with the continuing of test until to the end, (3 the calcareous sands’ AE activities was on the whole testing, (4 the calcareous sands’ particle crushing and mutual friction played different roles for its AE activities. Then the AE model based on the calcarous sands’ particle crushing was discussed.

Availability of ground water in the lower Pawcatuck River basin, Rhode Island

Science.gov (United States)

Gonthier, Joseph B.; Johnston, Herbert E.; Malmberg, Glenn T.

1974-01-01

The lower Pawcatuck River basin in southwestern Rhode Island is an area of about 169 square miles underlain by crystalline bedrock over which lies a relatively thin mantle of glacial till and stratified drift. Stratified drift, consisting dominantly of sand and gravel, occurs in irregularly shaped linear deposits that are generally less than a mile wide and less than 125 feet thick; these deposits are found along the Pawcatuck River, its tributaries, and abandoned preglacial channels. Deposits of stratified sand and gravel constitute the principal aquifer in the lower Pawcatuck basin and the only one capable of sustaining yields of 100 gallons per minute or more to individual wells. Water available for development in this aquifer consists of water in storage--potential ground-water runoff to streams--plus infiltration that can be induced from streams. Minimum annual ground-water runoff from the sand and gravel aquifer is calculated to be at least 1.17 cubic feet per second per square mile, or 0.76 million gallons per day per square mile. Potential recharge by induced infiltration is estimated to range from about 250 to 600 gallons per day per linear foot of streambed for the principal streams. In most areas, induced infiltration from streams constitutes the major source of water potentially available for development by wells. Because subsurface hydraulic connection in the sand and gravel aquifer is poor in several places, the deposits are conveniently divisible into several ground-water reservoirs. The potential yield from five of the most promising ground-water reservoirs is evaluated by means of mathematical models. Results indicate that continuous withdrawals ranging from 1.3 to 10.3 million gallons per day, and totaling 31 million gallons per day, are obtainable from these reservoirs. Larger yields may be recovered by different well placement, spacing, construction and development, pumping practice, and so forth. Withdrawals at the rates indicated will reduce

Comparison of Available Technologies for Fire Spots Detection via Linear Heat Detector

Directory of Open Access Journals (Sweden)

Miksa František

2016-12-01

Full Text Available It is very demanding to detect fire spots under difficult conditions with high occurrence of interfering external factors such as large distances, airflow difficultly, high dustiness, high humidity, etc. Spot fire sensors do not meet the requirements due to the aforementioned conditions as well as large distances. Therefore, the detection of a fire spot via linear heat sensing cables is utilized.

Laboratory studies of dune sand for the use of construction industry in Sri Lanka

Science.gov (United States)

de Silva Jayawardena, Upali; Wijesuriya, Roshan; Abayaweera, Gayan; Viduranga, Tharaka

2015-04-01

With the increase of the annual sand demand for the construction industry the excessive excavation of river sand is becoming a serious environmental problem in Sri Lanka. Therefore, it is necessary to explore the possibility for an alternative to stop or at least to minimize river sand mining activities. Dune sand is one of the available alternative materials to be considered instead of river sand in the country. Large quantities of sand dunes occur mainly along the NW and SE coastal belt which belong to very low rainfall Dry Zone coasts. The height of dune deposits, vary from 1m to about 30 meters above sea level. The objective of this paper is to indicate some studies and facts on the dune sand deposits of Sri Lanka. Laboratory studies were carried out for visual observations and physical properties at the initial stage and then a number of tests were carried out according to ASTM standards to obtain the compressive strength of concrete cylinders and mortar cubes mixing dune sand and river sand in different percentages keeping a constant water cement ratio. Next the water cement ratio was changed for constant dune sand and river sand proportion. Microscopic analysis shows that the dune sand consist of 95 % of quartz and 5 % of garnet, feldspar, illmenite and other heavy minerals with clay, fine dust, fine shell fragments and organic matters. Grains are sub-rounded to angular and tabular shapes. The grain sizes vary from fine to medium size of sand with silt. The degree of sorting and particle size observed with dune sands are more suited with the requirement of fine aggregates in the construction industry. The test result indicates that dune sand could be effectively used in construction work without sieving and it is ideal for wall plastering due to its'-uniformity. It could also be effectively used in concrete and in mortars mixing with river sand. The best mixing ratio is 75% dune sand and 25% river sand as the fine aggregate of concrete. For mortar the mixing

Effectiveness of Protective Action of Coatings from Moisture Sorption into Surface Layer of Sand Moulds

Directory of Open Access Journals (Sweden)

Kaźnica N.

2016-12-01

Full Text Available The results of investigations of the sorption process of surface layers of sand moulds covered by zirconium and zirconium - graphite alcohol coatings are presented in the paper. Investigations comprised two kinds of sand grains (silica sand and reclaimed sand of moulding sand with furan resin. Tests were performed under conditions of a high relative air humidity 75 - 85% and a constant temperature within the range 28 – 33°C. To evaluate the effectiveness of coatings protective action from moisture penetration into surface layers of sand moulds gravimetric method of quantitavie moisture sorption and ultrasonic method were applied in measurements.

On Pluvial Compaction of Sand

DEFF Research Database (Denmark)

Jacobsen, Moust

At the Institute of Civil Engineering in Aalborg model tests on dry sand specimens have been carried out during the last five years. To reduce deviations in test results, the sand laying technique has been carefully studied, and the sand mass spreader constructed. Preliminary results have been...

George Sand: últimas novelas, últimos ensueños...

Directory of Open Access Journals (Sweden)

Àngels Santa

2014-04-01

Full Text Available A propósito de la obra de George Sand, Œuvres complètes.Sous la direction de Béatrice Didier. 1870, I :Malgrétout. Édition critique par Dominique Laporte (París, Honoré Champion, 2013, 247 p. ISBN : 9782745322968 y de George Sand, Œuvres complètes.Sous la direction de Béatrice Didier. 1876 :La Tour de Percemont. Édition critique par Dominique Laporte (París, Honoré Champion, 2013, 247 p. ISBN : 9782745322951.

Technology unlocks tar sands energy

Energy Technology Data Exchange (ETDEWEB)

Law, C

1967-09-25

Tar sand processing technology has been developed primarily in the categories of extraction techniques and in-situ processing. In October, a $235 million venture into tar sand processing will be inspected by visitors from many points on the globe. A synthetic crude of premium quality will be flowing through a 16-in. pipeline from the Tar Island plant site of Great Canadian Oil Sands to Edmonton. This processing plant uses an extractive mining technique. The tar sand pay zone in this area averages approximately 150 ft in thickness with a 50-ft overburden. It has been estimated that the tar sands cannot be exploited when the formation thickness is less than 100 ft and overburden exceeds the same amount. This indicates that extraction techniques can only be used to recover approximately 15% of the tar sand deposits. An in-situ recovery technique developed by Shell of Canada is discussed in detail. In essence it is selective hydraulic fracturing, followed by the injection of emulsifying chemicals and steam.

Natural and human controls of the Holocene evolution of the beach, aeolian sand and dunes of Caesarea (Israel)

Science.gov (United States)

Roskin, J.; Sivan, D.; Shtienberg, G.; Roskin, E.; Porat, N.; Bookman, R.

2015-12-01

The study focuses on the Holocene appearance, chronology and drivers of beach sand deposition and inland aeolian sand transport around the Roman-Byzantine ruins of Caesarea, Israel. Beach sand, sand sheets, nebkha, linear and transverse dunes as well as parabolic and transverse interdunes along two transects were sampled in the current study down to their substrate. Sixteen new optically stimulated luminescence ages cluster at ∼5.9-3.3 ka, ∼1.2-1.1 ka (800-900 AD) and ∼190-120 years ago (1825-1895 AD) indicating times of middle and late Holocene sand sheet depositions and historical dune stabilization. The first age cluster indicates that beach sand accumulated when rates of global sea level rise declined around 6-5 ka. Until ∼4 ka sand sheets encroached up to 2.5 km inland. Historical and archaeological evidence points to sand mobilization since the first century AD. Sand sheets dating to 1.2-1.1 ka, coevally found throughout the dunefield represent sand stabilization due to vegetation reestablishment attributed to gradual and fluctuating decline in human activity from the middle Early Islamic period until the 10th century. Historical and chronological evidence of the existence of transverse and coppice dunes from the 19th century suggest that dunes only formed in the last few centuries. The study illustrates the initial role of natural processes, in this case decline in global sea level rise and the primary and later role of fluctuating human activity upon coastal sand mobility. The study distinguishes between sand sheets and dunes and portrays them as sensors of environmental changes.

Mites and spiders act as biological control agent to sand flies

Directory of Open Access Journals (Sweden)

Diwakar Singh Dinesh

2014-02-01

Full Text Available Objective: To find out natural biological control agents of sand flies vector of kala azar in Bihar, India. Methods: Sand flies collected from the field using CDC light trap installing overnight to the collection site scrutitinized for Phlebotomus argentipes, the established vector of visceral leishmaniasis. Blood fed adult females were confined in the insectary for its development of life cycle. During developmental stages 2nd to 4th instars larvae were examined closely by using compound microscope for mite infestation. Adult spider residing along with sand flies collected in trap were kept in cage along with sand flies and their activities were watched closely and recorded by video and picture. Results: Mites were found predating 2nd to 4th instars larvae only under the laboratory conditions and lowering down the population of sand flies up to basal level within 15 d after infestation. One specific spider was found eating blood fed female sand flies kept inside the cage (n=50 attacking on lower part of thoracic region to kill the sand fly and ate desired soft part. Conclusions: Both predators, mites and spiders are acting as biological control agents to larvae and adults of sand flies respectively resulting variable density of vectors due to variable association with these predators and also cause lowering the transmission of the disease as hidden natural controlling agent of sand flies. The extensive study will be of immense help in controlling sand flies without use of environmental pollutant i.e. chemical insecticide.

Influence of Reclamation Process on the Ecological Quality of Reclaim Sand

Directory of Open Access Journals (Sweden)

Dereń M.

2017-12-01

Full Text Available In this article, there were presented results of research on influence of reclamation process on the ecological quality of reclaim sand with furan resin used in nonferrous foundry. The quality of reclaimed sand is mainly define by two group of chemical substances from elution of reclaimed sand: Dissolves Organic Carbon (DOC and Total Dissolves Solids (TDS. Reclaimed sand used in test was prepared in experimental thermal reclaimer and mechanical vibration reclaimer REGMAS installed in Faculty of Foundry Engineering at University Of Science and Technology in Krakow. The reference point is molding sand shaking out and crumble in jaw crusher. Test of elution was made in accredited laboratory in Center For Research and Environmental Control in Katowice up to the standard with Dissolves Organic Carbon (DOC - PN-EN 1484:1999; Total Dissolves Solids (TDS - PN-EN 15216:2010. The standard for elution test is PN-EN 12457- 4:2006. Except that we were made loss of ignition test, to check how many resin was rest on sand grains.

ANN modelling for the determination of moulding sand matrix grain size

Directory of Open Access Journals (Sweden)

J. Jakubski

2011-10-01

Full Text Available One of the modern methods of the production optimisation are artificial neural networks. Neural networks are gaining broader and broader application in the foundry industry, among others for controlling melting processes in cupolas and in arc furnaces, for designing castings and supply systems, for controlling moulding sand processing, for predicting properties of cast alloys or selecting parameters of pressure castings. An attempt to apply neural networks for controlling the quality of bentonite moulding sands is presented in this paper. This is the assessment method of sands suitability by means of detecting correlations between their individual parameters. The presented investigations were obtained by using the Statistica 9.0 program. The aim of the investigations was to select the neural network suitable for prediction the moulding sand matrix grain size on the basis of the determined sand properties such as: permeability, compactibility, and compressive strength.

Bituminous sands : tax issues

International Nuclear Information System (INIS)

Patel, B.

2004-01-01

This paper examined some of the tax issues associated with the production of bitumen or synthetic crude oil from oil sands. The oil sands deposits in Alberta are gaining more attention as the supplies of conventional oil in Canada decline. The oil sands reserves located in the Athabasca, Cold Lake and Peace River areas contain about 2.5 trillion barrels of highly viscous hydrocarbons called bitumen, of which nearly 315 billion barrels are recoverable with current technology. The extraction method varies for each geographic area, and even within zones and reservoirs. The two most common extraction methods are surface mining and in-situ extraction such as cyclic steam stimulation (CSS); low pressure steam flood; pressure cycle steam drive; steam assisted gravity drainage (SAGD); hot water flooding; and, fire flood. This paper also discussed the following general tax issues: bituminous sands definition; bituminous sands leases and Canadian development expense versus Canadian oil and gas property expense (COGPE); Canadian exploration expense (CEE) for surface mining versus in-situ methods; additional capital cost allowance; and, scientific research and experimental development (SR and ED). 15 refs

Oil sands tax expenditures

International Nuclear Information System (INIS)

Ketchum, K; Lavigne, R.; Plummer, R.

2001-01-01

The oil sands are a strategic Canadian resource for which federal and provincial governments provide financial incentives to develop and exploit. This report describes the Oil Sands Tax Expenditure Model (OSTEM) developed to estimate the size of the federal income tax expenditure attributed to the oil sands industry. Tax expenditures are tax concessions which are used as alternatives to direct government spending for achieving government policy objectives. The OSTEM was developed within the business Income Tax Division of Canada's Department of Finance. Data inputs for the model were obtained from oil sands developers and Natural Resources Canada. OSTEM calculates annual revenues, royalties and federal taxes at project levels using project-level projections of capital investment, operating expenses and production. OSTEM calculates tax expenditures by comparing taxes paid under different tax regimes. The model also estimates the foregone revenue as a percentage of capital investment. Total tax expenditures associated with investment in the oil sands are projected to total $820 million for the period from 1986 to 2030, representing 4.6 per cent of the total investment. 10 refs., 2 tabs., 7 figs

Development tendencies of moulding and core sands

Directory of Open Access Journals (Sweden)

Stanislaw M. Dobosz1

2011-11-01

Full Text Available Further development of the technology for making moulding and core sands will be strictly limited by tough requirements due to protection of the natural environment. These tendencies are becoming more and more tense, so that we will reach a point when even processes, that from technological point of view fulfill high requirements of the foundry industry, must be replaced by more ecologically-friendly solutions. Hence, technologies using synthetic resins as binding materials will be limited. This paper presents some predictable development tendencies of moulding and core sands. The increasing role of inorganic substances will be noticed, including silicate binders with significantly improved properties, such as improved knock-out property or higher reclamation strength. Other interesting solutions might also be moulding sands bonded by geo-polymers and phosphate binders or salts and also binders based on degradable biopolymers. These tendencies and the usefulness of these binders are put forward in this paper.

Penggunaan Unit Slow Sand Filter, Ozon Generator dan Rapid Sand Filter Skala Rumah Tangga Untuk Meningkatkan Kualitas Air Sumur Dangkal Menjadi Air Layak Minum (Parameter Zat Organik dan Deterjen

Directory of Open Access Journals (Sweden)

Anindya Prawita Sari

2014-09-01

Full Text Available Air sumur merupakan air tanah yang sering kali digunakan masyarakat untuk aktivitas sehari-hari. Air sumur dengan kadar organik dan deterjen tinggi tidak layak dikonsumsi masyarakat karena dapat menyebabkan berbagai macam penyakit. Selain itu, adanya zat organik dan deterjen mempengaruhi warna dan bau air sumur sehingga tidak layak konsumsi. Slow sand filter merupakan unit pengolahan yang mampu meremoval zat organik pada air. Slow sand filter dan rapid sand filter tidak menggunakan bahan kimia dalam proses pengolahan sehingga lebih ekonomis dan efektif. Sedangkan ozon, efektif digunakan untuk meremoval zat organik yang ada dalam air dengan mengubah rantai zat organik menjadi lebih sederhana. Tujuan penelitian ini adalah untuk mengetahui keefektifan penggunaan slow sand filter, ozon generator dan rapid sand filter dalam menyisihkan beban deterjen dan zat organik pada air sumur. Hasil penelitian menunjukkan bahwa efisiensi removal pada unit slow sand filter untuk beban organik dan deterjen sebesar 57,6% dan 60,5 %, pada unit ozonasi sebesar 47,4% dan 17,5%, dan pada unit rapid sand filter sebesar 50,0% dan 50,9 %.

Microbial Characterization of Qatari Barchan Sand Dunes.

Directory of Open Access Journals (Sweden)

Sara Abdul Majid

Full Text Available This study represents the first characterization of sand microbiota in migrating barchan sand dunes. Bacterial communities were studied through direct counts and cultivation, as well as 16S rRNA gene and metagenomic sequence analysis to gain an understanding of microbial abundance, diversity, and potential metabolic capabilities. Direct on-grain cell counts gave an average of 5.3 ± 0.4 x 105 cells g-1 of sand. Cultured isolates (N = 64 selected for 16S rRNA gene sequencing belonged to the phyla Actinobacteria (58%, Firmicutes (27% and Proteobacteria (15%. Deep-sequencing of 16S rRNA gene amplicons from 18 dunes demonstrated a high relative abundance of Proteobacteria, particularly enteric bacteria, and a dune-specific-pattern of bacterial community composition that correlated with dune size. Shotgun metagenome sequences of two representative dunes were analyzed and found to have similar relative bacterial abundance, though the relative abundances of eukaryotic, viral and enterobacterial sequences were greater in sand from the dune closer to a camel-pen. Functional analysis revealed patterns similar to those observed in desert soils; however, the increased relative abundance of genes encoding sporulation and dormancy are consistent with the dune microbiome being well-adapted to the exceptionally hyper-arid Qatari desert.

Singing Sand Dunes

Indian Academy of Sciences (India)

ble low-frequency (s. 75–105 Hz), that can some- times be heard up to 10 km away. Scientific in- vestigations suggest that the sustained low fre- quency sound of sand dunes that resembles a pure note from a musical instrument, is due to the synchronized motion of well-sorted dry sand grains when they spontaneously ...

Study on Modified Sand Filtration Towards Water Quality of Wet Market Waste Water

Directory of Open Access Journals (Sweden)

Saad F.N.M.

2016-01-01

Full Text Available Investigation on the potential of sand filter as a pre-treatment of waste water was done in Kangar wet market, Perlis. Besides, the best composition of filter in order to treat wastewater based on BOD, COD, SS, AN, turbidity and pH levels are further examined. In this study, there are four types of sand filter composition which the medias consist of fine sand and coarse sand while the modified sand filter are consist of sand, course sand and activated carbon prepared from rice husk and coconut shells. After 10 weeks of treatment, the results show that the concentration of BOD, COD, SS, AN, turbidity and pH were reduced up to 86%, 84%, 63%, 88%, 73%, respectively while pH nearly to neutral with 6.83. Moreover, the result also revealed that the sand filter added with rice husk almost complied with Standard B of Malaysia Environmental Quality (Sewage Regulations 2009 as well as gives the highest number of WQI with 36.81. Overall, WQI obtained in this study are ranged from 12.77 to 36.81.

Characteristics and Dynamics of a Large Sub-Tidal Sand Wave Field—Habitat for Pacific Sand Lance (Ammodytes personatus, Salish Sea, Washington, USA

Directory of Open Access Journals (Sweden)

H. Gary Greene

2017-10-01

Full Text Available Deep-water sand wave fields in the San Juan Archipelago of the Salish Sea and Pacific Northwest Washington, USA, have been found to harbor Pacific sand lance (PSL, Ammodytes personatus, a critical forage fish of the region. Little is known of the dynamics of these sand waves and the stability of the PSL sub-tidal habitats. Therefore, we have undertaken an initial investigation to determine the dynamic conditions of a well-known PSL habitat in the San Juan Channel within the Archipelago using bottom sediment sampling, an acoustical doppler current profiling (ADCP system, and multi-beam echo sounder (MBES bathymetry. Our study indicates that the San Juan Channel sand wave field maintained its shape and bedforms geometry throughout the years it has been studied. Based on bed phase diagrams for channelized bedforms, the sand waves appear to be in a dynamic equilibrium condition. Sea level rise may change the current regime within the Archipelago and may alter some of the deep-water or sub-tidal PSL habitats mapped there. Our findings have global significance in that these dynamic bedforms that harbor PSL and sand-eels elsewhere along the west coast of North America and in the North Sea may also be in a marginally dynamic equilibrium condition and may be prone to alteration by sea level rise, indicating an urgency in locating and investigating these habitats in order to sustain the forage fish.

Strength and microstructure characteristics of the recycled rubber tire-sand mixtures as lightweight backfill.

Science.gov (United States)

Zhang, Tao; Cai, Guojun; Duan, Weihong

2018-02-01

The disposal of scrap rubber tires has induced critical environmental issue worldwide due to the rapid increase in the number of vehicles. Recycled scrap tires as a construction material in civil engineering have significant environmental benefits from a waste management perspective. A systematic study that deals with strength and microstructure characteristics of the rubber-sand mixtures is initiated, and mechanical response of the mixtures is discussed in this investigation. Experiments were conducted to evaluate the effects of rubber fraction on the basic properties including mass density (ρ), stress-strain characteristics, shear strength, and unconfined compression strength (q u ) of the rubber-sand mixtures. Additionally, scanning electron microscopy (SEM) was carried out to reveal the microstructure characteristics of the mixtures with various rubber fractions. A discussion on the micromechanics of the mixtures also was conducted. This study demonstrates that the ρ, friction angle, and q u decrease linearly with an increase in rubber fraction, whereas shear strain at peak increases. The stress-strain characteristics of the rubber-sand mixtures shift from brittle to ductile as the rubber fraction increase. These changes are attributed to remarkably lower stiffness and higher compressibility of the rubber particle compared with those of the conventional mineral aggregates. With an increase in the rubber fraction, the mechanical response of rubber-sand mixtures exhibits two types: sand-like material and rubber-like material. Rubber particle possesses the capacity to prevent the contacted sand particles from sliding at lower rubber fraction, whereas it transmits the applied loadings as the rubber fraction increased. This outcome reinforces the practicability of using recycled rubber tire-sand mixtures as a lightweight backfill in subbase/base applications.

The diffusion of sulphur from moulding sand to cast and methods of its elimination

Directory of Open Access Journals (Sweden)

M. Hosadyna

2009-10-01

Full Text Available The care of high quality castings requires taking into account the possible negative influence of decomposition products of moulding and core sands on the structure of castings produced. Such products are emitted both from the sands of I generation, meaning sands bound by bentonite, especially those containing carbon forming additives, as well as from the sands of II generation, meaning the sands with the binding materials or even the sands without any binders, such as the forms produced by using the LOST FOAM technology. The literature often refers to the negative effects of nitrogen emitted from the sands with the urea resins on the tendency to create surface defects. That is why the aim of this study was to assess the degree of sulphur diffusion to the ferroalloy castings and the proposal of its limitation.

Influence of Binding Rates on Strength Properties of Moulding Sands with the GEOPOL Binder

Directory of Open Access Journals (Sweden)

Holtzer M.

2014-03-01

Full Text Available The results of investigations of moulding sands with an inorganic binder called GEOPOL, developed by the SAND TEAM Company are presented in the paper. Hardeners of various hardening rates are used for moulding sands with this binder. The main aim of investigations was determination of the influence of the hardening rate of moulding sands with the GEOPOL binder on technological properties of these sands (bending strength, tensile strength, permeability and grindability. In addition, the final strength of moulding sands of the selected compositions was determined by two methods: by splitting strength and shear strength measurements. No essential influence of the hardening rate on such parameters as: permeability, grindability and final strength was found. However, the sand in which the slowest hardener (SA 72 were used, after 1 hour of holding, had the tensile and bending strength practically zero. Thus, the time needed for taking to pieces the mould made of such moulding sand will be 1.5 - 2 hours.

The estimation of harmfulness for environment of moulding sand with biopolymer binder based on polylactide

Directory of Open Access Journals (Sweden)

K. Major-Gabryś

2011-01-01

Full Text Available The article takes into consideration technological and ecological aspects of IV generation moulding sands. Investigations concerning anapplication of biopolymer materials as binders for moulding sands are presented in the paper. These investigations are the continuation ofexaminations related to applications of various biopolymers as binding agents and to the properties of the moulding sands with biopolymerbinders. In the paper there are the researches concerning analyzing gases emitted from moulding sands during heating.

Experimental Investigation of Evaporation and Drainage in Wettable and Water-Repellent Sands

Directory of Open Access Journals (Sweden)

Dae Hyun Kim

2015-05-01

Full Text Available This study presents experimental results on evaporation and drainage in both wettable and water-repellent sands whose surface wettability was artificially modified by silanization. The 2D optical and 3D X-ray computed tomographic imaging was performed during evaporation and the water retention during cyclic drainage and infiltration was measured to assess effects of wettability and initial wetting conditions. The evaporation gradually induces its front at the early stage advance regardless of the wettability and sand types, while its rate becomes higher in water-repellent Ottawa sand than the wettable one. Jumunjin sand which has a smaller particle size and irregular particle shape than Ottawa sand exhibits a similar evaporation rate independent of wettability. Water-repellent sand can facilitate the evaporation when both wettable and water-repellent sands are naturally in contact with each other. The 3D X-ray imaging reveals that the hydraulically connected water films in wettable sands facilitate the propagation of the evaporation front into the soil such that the drying front deeply advances into the soil. For cyclic drainage-infiltration testing, the evolution of water retention is similar in both wettable and water-repellent sands when both are initially wet. However, when conditions are initially dry, water-repellent sands exhibit low residual saturation values. The experimental observations made from this study propose that the surface wettability may not be a sole factor while the degree of water-repellency, type of sands, and initial wetting condition are predominant when assessing evaporation and drainage behaviors.

Natural infection of the sand fly Phlebotomus kazeruni by Trypanosoma species in Pakistan

Directory of Open Access Journals (Sweden)

Iwata Hiroyuki

2010-02-01

Full Text Available Abstract The natural infection of phlebotomine sand flies by Leishmania parasites was surveyed in a desert area of Pakistan where cutaneous leishmaniasis is endemic. Out of 220 female sand flies dissected, one sand fly, Phlebotomus kazeruni, was positive for flagellates in the hindgut. Analyses of cytochrome b (cyt b, glycosomal glyceraldehyde phosphate dehydrogenase (gGAPDH and small subunit ribosomal RNA (SSU rRNA gene sequences identified the parasite as a Trypanosoma species of probably a reptile or amphibian. This is the first report of phlebotomine sand flies naturally infected with a Trypanosoma species in Pakistan. The possible infection of sand flies with Trypanosoma species should be taken into consideration in epidemiological studies of vector species in areas where leishmaniasis is endemic.

Offshore Sand Resource Needs, Data Availability and Revaluation, and Beach Nourishment Projects in North Carolina

Science.gov (United States)

Conery, I.; Walsh, J. P.

2016-12-01

Storms and sea-level rise continue to impact the dynamic coastlines of North Carolina. Since the coastal region is economically critical to the state and yields numerous ecosystem services, many towns have planned beach nourishment projects. However, offshore sands compatible for nourishment are limited, and project costs fluctuate with borrow source proximity to the shoreline. Hurricane Sandy (2012) caused high water levels and waves resulting in localized overwash and erosion in the northeastern part of NC. In response, to effectively meet the rising nourishment demands for recovery after future storm events and for long-term resiliency, the Bureau of Ocean Energy Management (BOEM) recognized the need to compile and consolidate all geophysical and geologic information in federal waters (3-8 nm) along the East Coast states. A GIS database was created for NC using bathymetric, seismic reflection, sediment and other relevant data from federal, state and private entities. Information will be accessible to the public, coastal planners and managers to allow for informed decision-making and cost-effective project planning. Priority regions for seismic and core collection were determined based on data gaps and needs across the state. In addition, potential sand resource thickness and volume in northeastern NC were revaluated using comparisons of several overlapping datasets. Shoreline volume losses were calculated using long-term erosion rates and compared to historic and future nourishment projects. Finally, tourism-based revenue by town was evaluated and related to short and long-term nourishment costs.

Performance monitoring of electric shovels digging oil sands

Energy Technology Data Exchange (ETDEWEB)

Patnayak, S. [Alberta Univ., Edmonton, AB (Canada). Natural Resources Engineering Facility; Tannant, D.D. [Alberta Univ., Edmonton, AB (Canada). School of Mining and Petroleum Engineering; Parsons, I. [Syncrude Canada Ltd., Edmonton, AB (Canada). Edmonton Research Centre; Del Valle, V. [Syncrude Canada Ltd., Fort McMurray, AB (Canada)

2005-07-01

Some of the largest available mining equipment is used for oil sand mining operations. However, the performance of electric cable shovels varies with the diggability characteristics of the ground. In particular, oil sands diggability with cable shovels depends on structural geology, the depositional environment and geotechnical parameters. This paper described some of the key shovel performance indicators such as dig cycle time, digging energy and digging power. In winter, frost penetration can also affect oil sands diggability. The challenge of hard digging in oil sands is often addressed by blasting or ripping, which increases the cost of production and impedes productivity. The shovel performance is also influenced by other parameters such as operator skills, bucket and tooth design and shovel dipper trajectory. This paper demonstrated that hoist and crowd motor voltages and currents are useful in identifying the beginning and end of dig cycles. Performance indicators such as dig cycle time, hoist motor energy and power, and crowd motor energy and power were considered to assess material diggability. It was suggested that hoist power represents the ground diggability better than other performance indicators. 5 refs., 1 tab., 10 figs.

Experimental study on swelling character of statics-compacted bentonite-sand mixture

International Nuclear Information System (INIS)

Cui Suli; Zhang Huyuan; Liu Jisheng; Liang Jian

2010-01-01

In the high-level radioactive waste (HLW) geological disposal projects barrier system, there are two types for constructing buffer/backfill material in preconceived: locale field-pressed and locale-build by prefab lock. Statics-Compacted is needed for both footrill padding in the locale field-pressed and locale-build by prefab lock. Laboratory tests were conducted on statics-compacted mixture of GMZ001 bentonite and quartz sand in different addition. The results obtained indicated that in the semi-log coordinates, the form of the P-time and e-time curves were sigmoid,the same as dynamic-compacted specime. The swelling character of statics-compacted specime were also as well as dynamic-compacted specime, that is with the increase of initial dry density, the maximum swelling pressure were exponential increase and maximum swelling strain increase linearly. These made it clear that the methods of making specime have no effect on the swelling character of bentonite-sand mixture, so methods for constructing buffer/backfill material can be selected free as needed in the construction site. The validity of regression relationship received by dynamic-compacted specime test was verified, and the coefficients for the regression equation were revised in a greater range of initial dry density. Based on the comprehensive analysis of experimental results, it is concluded that addition of 10-30% quartz sand and 1.60-1.80 g/cm 3 for initial dry density to GMZ001 bentonite-sand mixture is suitable for the swelling quality. (authors)

Thermal Conductivity of Moulding Sand with Chemical Binders, Attempts of its Increasing

Directory of Open Access Journals (Sweden)

Zych J.

2015-04-01

Full Text Available The investigation results of the thermal conductivity of the selected group of moulding sands with chemical binders, mainly organic, are presented in the hereby paper. Studies encompassed also moulding sands into which additions improving the thermal conductivity were introduced. Two testing methods were applied, i.e. investigations at a steady and unsteady temperature zone. For investigations at a steady temperature zone the new original experimental stand was designed and built, adapted also for testing moulding sands with binders undergoing destruction at relatively low temperatures.

Influence of Geometric Parameters of the Hydrocyclone and Sand Concentration on the Water/Sand/Heavy-Oil Separation Process: Modeling and Simulation

Directory of Open Access Journals (Sweden)

F Farias

2016-09-01

Full Text Available In the oil exploitation, produced fluids are composed of oil, gas, water and sand (depending on the reservoir location. The presence of sand in flow oil leads to several industrial problems for example: erosion and accumulation in valves and pipeline. Thus, it is necessary to stop production for manual cleaning of equipments and pipes. These facts have attracted attention of academic and industrial areas, enabling the appearing of new technologies or improvement of the water/oil/sand separation process. One equipment that has been used to promote phase separation is the hydrocyclone due to high performance of separation and required low cost to installation and maintenance. In this sense, the purpose of this work is to study numerically the effect of geometric parameters (vortex finder diameter of the hydrocyclone and sand concentration on the inlet fluid separation process. A numerical solution of the governing equations was obtained by the ANSYS CFX-11 commercial code. Results of the streamlines, pressure drop and separation efficiency on the hydrocyclone are presented and analyzed. It was observed that the particles concentration and geometry affect the separation efficiency of the hydrocyclone.

Crushed and River-Origin Sands Used as Aggregates in Repair Mortars

Directory of Open Access Journals (Sweden)

Maria Stefanidou

2016-04-01

Full Text Available The systematic analysis of mortars from monuments or historic buildings and the simultaneous study of the construction environment show that it was common practice to use naturally occurring sand from local rivers or streams for the production of the mortars. There are cases though, mainly on islands, where sands of natural origin were limited, and marine or crushed sands were used possibly after elaboration. In all cases the particle size analysis of old mortar confirms the presence of even distribution of the granules. As regards the design of the repair mortars, there are criteria that should be taken into consideration in order to produce materials with compatible properties. The main properties concerning sands are the grain distribution and maximum size, the color, the content of fines, and soluble salts. The objective of this research is the study of the physical characteristics of the sands such as the sand equivalent, the gradation, the apparent density, the morphology of the grains, their mineralogical composition and the influence of these properties on the behavior of lime mortars, notably the mechanical and physical properties acquired.

IMPROVEMENT OF EQUIPMENT FOR EFFECTIVE HARDENING SAND MIXTURE BY VACUUM MOLDING

Directory of Open Access Journals (Sweden)

V. S. Doroshenko

2016-01-01

Full Text Available The review deals with the design flask tooling and patterns for effective hardening sand mixture in the vacuum molding (V-Process, and molding on a one-off patterns (Lost Foam Casting. Sealing and evacuating sand mixture – two major factors influence the strength of the casting mold and casting quality, management practices which will enable to improve the casting process.

A Late Pleistocene linear dune dam record of aeolian-fluvial dynamics at the fringes of the northwestern Negev dunefield

Science.gov (United States)

Roskin, Joel; Bookman, Revital; Friesem, David; Vardi, Jacob

2017-04-01

The paper presents a late Pleistocene aeolian-fluvial record within a linear dune-like structure that partway served as a dune dam. Situated along the southern fringe of the northwestern Negev desert dunefield (Israel) the structure's morphology, orientation, and some of its stratigraphic units partly resemble adjacent west-east extending vegetated linear dunes. Uneven levels of light-colored, fine-grained fluvial deposits (LFFDs) extend to the north and south from the flanks of the studied structure. Abundant Epipalaeolithic sites line the fringes of the LFFDs. The LFFD microstructures of fine graded bedding and clay blocky peds indicate sorting and shrinking of saturated clays in transitional environments between low energy flows to shallow standing water formed by dunes damming a mid-sized drainage system. The structure's architecture of interchanging units of sand with LFFDs indicates interchanging dominances between aeolian sand incursion and winter floods. Sand mobilization associated with powerful winds during the Heinrich 1 event led to dune damming downstream of the structure and within the structure to in-situ sand deposition, partial fluvial erosion, reworking of the sand, and LFFD deposition. Increased sand deposition led to structure growth and blockage of its drainage system that in turn accumulated LFFD units up stream of the structure. Extrapolation of current local fluvial sediment yields indicate that LFFD accretion up to the structure's brim occurred over a short period of several decades. Thin layers of Geometric Kebaran (c. 17.5-14.5 ka cal BP) to Harifian (12-11 ka BP) artifacts within the structure's surface indicates intermittent, repetitive, and short term camping utilizing adjacent water along a timespan of 4-6 kyr. The finds directly imply that the NW Negev LFFDs formed in dune-dammed water bodies which themselves were formed following events of vegetated linear dune elongation. LFFD accumulation persisted as a result of dune dam

POSSIBILITY OF BENEFICIATION OF SILICA SAND FROM THE CROATIAN DEPOSITS USING ATTRITION SCRUBBING

Directory of Open Access Journals (Sweden)

Ivan Sobota

2011-12-01

Full Text Available To meet high quality requirements defined for specific industrial applications, the raw sand often has to be subjected to extensive physical and chemical processing. The possibility of achieving silica sand concentrate of required quality depends mostly on raw sand properties, primarily mineral impurity types and contents, and features of applied beneficiation methods. When the impurities occur in the form of oxide coatings on the surfaces of the single sand grains, attriton scrubbing is applied. By reducing the proportion of oxide coatings on the grains, the quality of sand can be improved. With the aim to determine the possibilities of the beneficiation of silica sand from significant Croatian deposits (“Vrtlinska”, “Štefanac” and “Španovica” and achieve concentrate grade complying with the requirements of domestic industry, laboratory tests were conducted on three raw sand samples with different SiO2 and impurity contents. Grain size distribution, chemical and mineral composition of raw sand samples, and the possibility of their quality improvement by applying the washing, classification and attrition scrubbing were defined by analysis of test results (the paper is published in Croatian.

Field test on sand compaction pile method with copper slag sand; Dosuisai slag wo mochiita SCP koho no shiken seko

Energy Technology Data Exchange (ETDEWEB)

Minami, K.; Matsui, H.; Naruse, E.; Kitazume, M. [Port and Harbour Research Inst., Kanagawa (Japan)

1997-09-20

This paper describes the sand compaction pile (SCP) method using copper slag sand. The SCP method is a method by which sand compaction piles are constructed in the ground, and improvement can be obtained in a short period. This method has been widely used even in the port areas for enhancing the bearing power of soft clay ground and the lateral resistance of sheet pile. A great deal of sand is required as a material. The sand requires high permeability, proper size distribution with less fine particle fraction content, easy compaction property with enough strength, and easy discharging property from the casing of construction machines as required properties. Recently, it becomes hard to secure proper sand materials. The copper slag sand is obtained from refining process of copper as a by-product which is quenched in water flow and crushed in water. The copper slag sand has higher particle density than that of sand, excellent permeability, and similar size distribution to that of sand. From compaction drainage triaxial compression test and permeability test, it was found that the mechanical properties of copper slag sand did not change by the crushing of grains with keeping excellent permeability. Through the test construction, applicability of the copper slag sand to the SCP method could be confirmed as an alternate material of sand. 17 refs., 9 figs., 4 tabs.

Study on strength characteristics of concrete using M-Sand and coconut fibers

Science.gov (United States)

Neeraja, D.; Wani, Amir Iqbal; Kamili, Zainulabideen; Agarwal, Krishnakant

2017-11-01

In the current world, concrete has become a very important part of the construction industry and the materials which are used in making concrete have evolved due to better quality of cement and better grade of coarse aggregates. The sand is an important part of concrete. It is mainly procured from natural sources. Thus the grade of sand is not under our control. The methods of removing sand from river beds are causing various environmental issues and river sand is depleting at a faster rate than it is replaced by natural methods. Hence, various replacements for the river sand are being done, one of which is manufactured-sand. It is obtained from various granite quarries. Manufactured-sand or M-sand is slowly replacing the fine aggregate in the concrete as the sand is well graded and gives higher strength of concrete. There are various fibers used for reinforcing concrete which consist mainly of artificial or steel fibers. Some of these fibers are quite costly and sometimes difficult to obtain. So there are many natural fibers which can be used in place of these fibers, one of which is coconut fiber, extracted from the shell of a coconut. Coconut fibers are used in various industries like rope making, coir mattresses etc. Since these fibers are one of the strongest fibers among naturally occuring fibers, they can be used in the concrete mix to increase the resistance in concrete. They are also light weight and easily available and thus can be used in reinforcement of concrete. The studies up till now have tested the use of coconut fibers in normal concrete involving river sand but in this study a particular ratio of M-sand and river sand is used to get the maximum possible strength. Hence, in this project an attempt was made to use M-sand and coconut fiber in concrete. Based on the test results, it can be concluded that combination of M-sand and coconut fibers gave favorable results in strength criteria.

A Primer on Alberta’s Oil sands Royalties

Directory of Open Access Journals (Sweden)

Sarah Dobson

2015-12-01

Full Text Available Fulfilling its campaign promise, the new NDP government announced a review of Alberta’s royalty framework in June 2015. The province receives royalty revenue from three main sources – natural gas, crude oil, and oil sands. Since the 2009-10 fiscal year the largest contributor to Alberta’s royalty revenues has been the oil sands. If you want a sense of how important oil sands royalties have been for Alberta’s finances, consider this: In the 2014–15 fiscal year, the government collected just over $5 billion from oil sands royalties. These royalties covered over 10 per cent of the province’s operational expenses of $48.6 billion in the same fiscal year. Over the last six fiscal years the oil sands have contributed an average of 10 per cent of revenues to provincial coffers. This makes oil sands royalties the fourth largest contributor behind personal income taxes (23 per cent, federal transfers (13 per cent and corporate income taxes (11 per cent. But how many Albertans really understand how the royalty system works? What do we mean when we say “royalty”? How does the Alberta Government calculate royalties on oil sands producers? If the system is going to change, it’s important that Albertans understand how the current system works. That is what this paper is designed to do. For Albertans to properly judge the impact of new policy, they need a solid understanding of the current policy environment. We all know that oil prices have dropped and oil sands producers are losing profitability. As such, changes to the royalty system could have a deep and profound impact on the sector. Here are some of the issues this primer will study: • Pre-payout projects vs. post-payout projects, in other words, the classification of projects for royalty purposes based on whether the cumulative costs of a project exceed its cumulative revenues • Monthly payment of royalties vs. annual payment • Understanding the unit price of bitumen and how that

Pullout capacity of batter pile in sand

Directory of Open Access Journals (Sweden)

Ashraf Nazir

2013-03-01

Full Text Available Many offshore structures are subjected to overturning moments due to wind load, wave pressure, and ship impacts. Also most of retaining walls are subjected to horizontal forces and bending moments, these forces are due to earth pressure. For foundations in such structures, usually a combination of vertical and batter piles is used. Little information is available in the literature about estimating the capacity of piles under uplift. In cases where these supporting piles are not vertical, the behavior under axial pullout is not well established. In order to delineate the significant variables affecting the ultimate uplift shaft resistance of batter pile in dry sand, a testing program comprising 62 pullout tests was conducted. The tests are conducted on model steel pile installed in loose, medium, and dense sand to an embedded depth ratio, L/d, vary from 7.5 to 30 and with various batter angles of 0°, 10°, 20°, and 30°. Results indicate that the pullout capacity of a batter pile constructed in dense and/or medium density sand increases with the increase of batter angle attains maximum value and then decreases, the maximum value of Pα occurs at batter angle approximately equal to 20°, and it is about 21–31% more than the vertical pile capacity, while the pullout capacity for batter pile that constructed in loose sand decreases with the increase of pile inclination. The results also indicated that the circular pile is more resistant to pullout forces than the square and rectangular pile shape. The rough model piles tested is experienced 18–75% increase in capacity compared with the smooth model piles. The suggested relations for the pullout capacity of batter pile regarding the vertical pile capacity are well predicted.

Advanced oxidation and adsorption modification of dust waste from standard moulding sands

Directory of Open Access Journals (Sweden)

A. Baliński

2010-04-01

Full Text Available The article discusses the process of advanced oxidation (AO with application of ultrasounds and surface modification of the dust waste collected during dry dedusting of processed moulding sands with bentonite binder. A beneficial effect of both AO and adsorption modification of dust waste, when performed with the selected type of polyelectrolyte, on the technological and mechanical properties of moulding sands prepared with an addition of this dust has been stated. In spite of the bentonite content in moulding sand reduced by 43% and replaced with modified dust waste, the mechanical properties, i.e. the compression and tensile strengths, examined on sand specimens have been improved by 10% and 13%, respectively, with no harm to other basic technological sand properties. At the same time, it was also possible to reduce by about 30% the emission rate of the main gaseous component from the BTEX group, i.e. benzene.

PROSPECTS FOR APPLICATION OF COMPLEX-MODIFIED SAND ASPHALT CONCRETE IN ROAD CONSTRUCTION

Directory of Open Access Journals (Sweden)

D. Yu. Alexandrov

2017-01-01

Full Text Available The paper considers a possibility to use sand asphalt concrete as a material for protection of asphalt concrete and cement concrete road pavements against affection of external destructive factors. Advantages and disadvantages of sand asphalt concrete road pavements have been determined in the paper. The paper provides recommendations on improvement of sand asphalt concrete properties and contains an analysis of possible variants for usage of complex-modified sand asphalt concrete in the road construction. It has been noted that according to its potentially possible physical and mechanical properties activated quartz sand being micro-reinforced by dispersive industrial wastes is considered as an efficient component for creation of constructive layers in road asphalt concrete pavements. The paper reveals only specific aspects of the efficient application of quartz sand in road asphalt concrete. The subject of the paper loоks rather interesting for regions where there are no rock deposits for obtaining broken-stone ballast but there is rather significant spreading of local quarts sand. Its successful application is connected with the necessity to develop special equipment for physical and chemical activation of sand grain surface that permits strongly to increase an adhesive strength in the area of phase separation within the “bitumen–SiO2” system. The considered problem is a topical one and its solution will make it possible to local sand in a maximum way and partially to exclude application of broken stone in road construction.

Naphtha evaporation from oil sands tailings ponds

Energy Technology Data Exchange (ETDEWEB)

Kasperski, K.; Munoz, V.; Mikula, R. [Natural Resources Canada, Devon, AB (Canada). CANMET Western Research Centre

2010-07-01

The environmental impacts of volatile organic compounds (VOCs) from oil sands tailings ponds must be considered when evaluating new oil sands mining and extraction operations. Studies have suggested that only 40 percent of the solvent sent to tailings ponds is available to the environment, while the rest is irreversibly trapped. The recovery of hydrocarbons from oil sands froth process water is low. This PowerPoint presentation discussed a method of distinguishing between water and hydrocarbons at low temperatures. Samples were heated to 246 degrees C at 15 degrees C and held for 10 minutes. Heating was then resumed at 750 degrees C and held for 10 minutes in a pyrolysis phase, then cooled and reheated with an oxygen addition. The method demonstrated that the diluent distribution between the solids and water phases is misinterpreted as diluent that will evaporate, and diluent that will not evaporate. The study concluded by suggesting that the definition of recoverable and unrecoverable hydrocarbon should be re-termed as easily recoverable, and difficult to recover. tabs., figs.

Practical technical solution for clay-contaminated sands used in concrete

Directory of Open Access Journals (Sweden)

Estephane Pierre

2017-01-01

Full Text Available Sand, whether natural or manufactured, shows in many instances varying degrees of high levels of clay contamination. This fact is encountered in different parts of the globe and can lead to serious problems in adjusting concrete mix proportions and requiring high water to cement ratios and/or high dosages of superplasticizers without necessarily meeting the workability requirements, even when the sand is previously washed with fresh water. In this paper, different types of sand from the Gulf Cooperation Council (GCC region are being screened, analysed for their clay contents and consequent effects on plastic concrete quality. A technical solution is being proposed based on engineered superplasticizers. A testing protocol has been established to verify the robustness of optimized mix designs demonstrating the performance of the admixture in terms of initial and extended workability. In particular, it will be demonstrated that the customized concrete admixtures constitute by themselves a stand-alone answer to the usage of clay-contaminated sands in concrete.

Problems of bentonite rebonding of synthetic system sands in turbine mixers

Directory of Open Access Journals (Sweden)

A. Fedoryszyn

2008-12-01

Full Text Available Turbine (rotor mixers are widely used in foundries for bentonite rebonding of synthetic system sands. They form basic equipment in modern sand processing plants. Their major advantage is the short time of the rebond mixing cycle.Until now, no complete theoretical description of the process of mixing in turbine mixers has been offered. Neither does it seem reasonable to try to adapt the theoretical backgrounds of the mixing process carried out in mixers of other types, for example, rooler mixers [1], to the description of operation of the turbine mixers. Truly one can risk the statement that the individual fundamental operations of mixing in rooler mixers, like kneading, grinding, mixing and thinning, are also performed in turbine mixers. Yet, even if so, in turbine mixers these processes are proceeding at a rate and intensity different than in the roller mixers. The fact should also be recalled that the theoretical backgrounds usually relate to the preparation of sand mixtures from new components, and this considerably restricts the field of application of these descriptions when referred to rebond mixing of the system sand. The fundamentals of the process of the synthetic sand rebonding with bentonite require determination and description of operations, like disaggregation, even distribution of binder and water within the entire volume of the rebonded sand batch, sand grains coating, binder activation and aeration.This study presents the scope of research on the sand rebonding process carried out in turbine mixers. The aim has been to determine the range and specific values of the designing and operating parameters to get optimum properties of the rebonded sand as well as energy input in the process.

Galveston Island, Texas, Sand Management Strategies

Science.gov (United States)

2016-07-01

billion m3 of beach quality sand . However, Texas projects to date have not utilized these sources because of transportation costs. The lack of nearby...estimate that the San Luis Pass flood shoal contains approximately 11.8 million yd3 of beach quality sand . However, it is expected that if permits...a source of beach- quality sand . 2. Sand could be intercepted before it reaches the present dry beach. ERDC/CHL TR-16-13 55 3. The volume of

Longshore sediment transport at Golden Sands (Bulgaria

Directory of Open Access Journals (Sweden)

Hristo Nikolov

2006-09-01

Full Text Available The paper presents the results of studies on the qualitative and quantitative features of the littoral drift at Golden Sands (Bulgaria, carried out jointly by Polish and Bulgarian researchers. The mathematical modelling of physical coastal processes took wave transformation (wave diffraction and refraction; the effects of shoaling and wave breaking and longshore sediment transport into account. The computations were carried out for the mean statistical annual wave climate, determined on the basis of IO BAS wave data, simulated using the WAM method from long-term Black Sea wind data. The results of sediment transport computations clearly show that its direction off the Golden Sands shore is from north to south.

Simulating Sand Behavior through Terrain Subdivision and Particle Refinement

Science.gov (United States)

Clothier, M.

2013-12-01

their proximity to the interacting object or force with the sand. To illustrate an example, as a rover wheel moves forward and approaches a particular sand region, that region will continue to subdivide until individual sand particles are represented. Conversely, if the rover wheel moves away, previously subdivided sand regions will recombine. Thus, individual sand particles are available when an interacting force is present but stored away if there is not. As such, this technique allows for many particles to be represented without the computational complexity. We have also further generalized these subdivision regions in our sand framework into any volumetric area suitable for use in the simulation. This allows for more compact subdivision regions and has fine-tuned our framework so that more emphasis can be placed on regions of actively participating sand. We feel that this increases the framework's usefulness across scientific applications and can provide for other research opportunities within the earth and planetary sciences. Through continued collaboration with our academic partners, we continue to build upon our sand simulation framework and look for other opportunities to utilize this research.

Log analysis in the shallow oil sands of the San Joaquin Valley, California

International Nuclear Information System (INIS)

Vohs, J.B.

1976-01-01

Many fields in the San Joaquin Valley of California produce oil from a depth of 2,500 ft or less. During the period of primary production in these fields, evaluation of potential pay intervals from logs was restricted to examination of ES logs and correlation. With the introduction of secondary and tertiary recovery techniques the need for more and better answers, more quickly available, became apparent. However, several log-analysis problems had to be resolved. Formation evaluation using well logs was complicated by the shaliness of the sand intervals, the low and variable salinity of the formation waters, and the presence of low-pressure-gas (depleted) zones in many of the shallow sands. Solutions to these problems have required more modern logging programs and interpretation techniques. Logs available for the evaluation of these sands are the dual induction-laterolog, the compensated formation density log, the compensated neutron log, and the microlaterolog or proximity log. With this suite of logs it is possible to determine the shale content, porosity, saturation in the flushed zone, and water saturation of the sand, and to locate the low-pressure-gas sands and depleted zones. In cases where freshwater and oil are interlayered, it is possible to tell which sands contain oil and which contain only water. Because a quick interpretation is required, wellsite techniques are called for. These will be described

The Suitability Of Local Quartz Sand In The Production Of Bath Crucibles.

Directory of Open Access Journals (Sweden)

C. O. Okpanachi

2017-03-01

Full Text Available The suitability of local quartz sand in the production of bath crucibles is a study that was carried out in order to impart overall strength on bath crucibles hence reduce breakages during fettling. Therefore this research constitutes a study to enhance the efficiency of production of bath crucibles by addition of quartz sand in slip preparation. The steps taken in the beneficiation of quartz sand for the production of bath crucibles are comminution which entails crushing and milling classification washing liquid dispersion sizing and reduction of iron content by magnetic separation. The slip contains materials like plastic clay feldspar kaolin talc sodium silicate water quartz sand etc. These were all milled in the ball mill for slip production casting and fettling glazing and sintering to get final bath crucibles as the end products. Quartz sand is used in a variety of products essentially as raw material for the foundry casting and glass industries and also in chemicals water filtration and ceramics the heat resistance nature of quartz sand makes it an excellent refractory substance for these industrial processes. Slip can be prepared for production of bath crucibles without the inclusion of quartz sand however the addition of quartz sand is needed to improve the mechanical performance of the slip in the production of bath crucibles.

Influence of the Reclaim Addition on Properties of Moulding Sands with the Geopol Binder

Directory of Open Access Journals (Sweden)

Drożyński D.

2015-03-01

Full Text Available The investigation results of the influence of the reclaim additions on the properties of moulding sands with the GEOPOL geopolymer binder developed by the SAND TEAM Company were presented. Two brands of hardeners were applied in the tested compositions, the first one was developed by the SAND TEAM Company, marked SA72 and the new hardener offered by the KRATOS Company, marked KR72. The main purpose of investigations was to determine the influence of reclaim fractions and the applied hardener on the basic moulding sands properties, such as: bending and tensile strength, permeability and grindability. The unfavourable influence of the reclaim additions into moulding sands on the tested properties as well as an increased hardening rate, were found. Moulding sands, in which the hardener KR72 of the KRATOS Company was used, were less sensitive to the reclaim additions

Japan's involvement in oil sands development

International Nuclear Information System (INIS)

Sugiura, T.

1994-01-01

According to Japanese national policy, exploration and development by Japanese companies in overseas countries are promoted in order to ensure stable oil supplies. Japan Canada Oil Sands Limited (JACOS), part of the JAPEX group, was established during the 1978 world oil crisis to explore and develop Canadian oil sand resources in accordance with Japan's national policy. The JAPEX group, including JACOS, has invested $123 million in oil sands projects in Alberta. JAPEX's first involvement in oil sands was in the Primrose Project operated by Norcen in the Cold Lake area. Five years of cyclic steam stimulation pilot tests did not produce sufficiently good results to justify further operation. The second involvement was the PCEJ Project, a joint effort by four companies that are participating in a bitumen recovery test project in the Athabasca Deposit. JACOS holds 2,452 km 2 of oil sands leases in Alberta. Tests conducted since 1978 in the PCEJ Project include multiwell steam injection pilot tests, some of which showed promise. JACOS is also participating in steam assisted gravity drainage projects and in federal/provincial research programs. Obstacles identified in developing Alberta oil sands are the lack of a bitumen pipeline to Edmonton and the insufficient length of oil sands leases (currently 10 years), given the difficulties of oil sand development. 10 figs

A Simple Slow-Sand Filter for Drinking Water Purification

Directory of Open Access Journals (Sweden)

K. O. Yusuf

2017-04-01

Full Text Available Water-borne diseases are commonly encountered when pathogen-contaminated water is consumed. In rural areas, water is usually obtained from ponds, open shallow wells, streams and rain water during rainy season. Rain water is often contaminated by pathogens due to unhygienic of physical and chemical conditions of the roofs thereby making it unsafe for consumption. A simple slow sand filter mechanism was designed and fabricated for purification of water in rural areas where electricity is not available to power water purification devices. Rain water samples were collected from aluminum roof, galvanized roof and thatched roof. The waters samples were allowed to flow through the slow sand filter. The values of turbidity, total dissolved solids, calcium, nitrite, faecal coliform and total coliform from unfiltered water through thatched roof were 0.92 NTU, 27.23 mg/l, 6 mg/l, 0.16 mg/l, 5cfu/100ml and 6.0 cfu/100ml, respectively while the corresponding values for slow sand filter from thatched roof were 0.01 NTU, 0.23 mg/l, 2.5 mg/l, 0.1 mg/l, 0 cfu/100ml and 0 cfu/100ml, respectively. The values of turbidity, total dissolved solid, nitrite, calcium, faecal coliform and total coliform from unfiltered water for aluminum roof were 0.82 NTU, 23.68 mg/l, 2.70 mg/l, 1.0 mg/l, 4 cfu/100ml and 4cfu/100ml, respectively while the corresponding values for slow sand filter were 0.01 NTU, 0.16 mg/l, 0.57 mg/l, 0.2 mg/l, 0 cfu/100ml and 0 cfu/100ml, respectively. The values obtained for galvanized roof were also satisfactory. The slow sand filter is recommended for used in rural areas for water purification to prevent risk of water-borne diseases.

Changes of gas pressure in sand mould during cast iron pouring

Directory of Open Access Journals (Sweden)

J. Mocek

2011-10-01

Full Text Available The paper presents a test method developed to measure changes of gas pressure in sand moulds during manufacture of iron castings. The pressure and temperature measurements were taken in the sand mould layers directly adjacent to the metal – mould interface. A test stand was described along with the measurement methodology. The sensors used allowed studying the fast-changing nature of the processes which give rise to the gas-originated casting defects. The study examined the influence of binders, clays and refining additives on the nature of the gas evolution process. The effect of the base sand type - quartz or olivine - on the nature of pressure changes was compared. The test stand design ensured the stability of technological parameters in the examined mould elements, and a repeatable process of making pilot castings. The main outcome was classification of sand mixtures in terms of pressure occurring during pouring of iron castings. The obtained results confirm the usefulness of the described method for testing gas pressure occurrence in a sand mould.

Policy Analysis of the Canadian Oil Sands Experience

Energy Technology Data Exchange (ETDEWEB)

None, None

2013-09-01

For those who support U.S. oil sands development, the Canadian oil sands industry is often identified as a model the U.S. might emulate, yielding financial and energy security benefits. For opponents of domestic oil sands development, the Canadian oil sands experience illustrates the risks that opponents of development believe should deter domestic policymakers from incenting U.S. oil sands development. This report does not seek to evaluate the particular underpinnings of either side of this policy argument, but rather attempts to delve into the question of whether the Canadian experience has relevance as a foundational model for U.S. oil sands development. More specifically, this report seeks to assess whether and how the Canadian oil sands experience might be predictive or instructive in the context of fashioning a framework for a U.S. oil sands industry. In evaluating the implications of these underpinnings for a prospective U.S. oil sands industry, this report concentrates on prospective development of the oil sands deposits found in Utah.

The Diversity of Yellow-Related Proteins in Sand Flies (Diptera: Psychodidae.

Directory of Open Access Journals (Sweden)

Michal Sima

Full Text Available Yellow-related proteins (YRPs present in sand fly saliva act as affinity binders of bioamines, and help the fly to complete a bloodmeal by scavenging the physiological signals of damaged cells. They are also the main antigens in sand fly saliva and their recombinant form is used as a marker of host exposure to sand flies. Moreover, several salivary proteins and plasmids coding these proteins induce strong immune response in hosts bitten by sand flies and are being used to design protecting vaccines against Leishmania parasites. In this study, thirty two 3D models of different yellow-related proteins from thirteen sand fly species of two genera were constructed based on the known protein structure from Lutzomyia longipalpis. We also studied evolutionary relationships among species based on protein sequences as well as sequence and structural variability of their ligand-binding site. All of these 33 sand fly YRPs shared a similar structure, including a unique tunnel that connects the ligand-binding site with the solvent by two independent paths. However, intraspecific modifications found among these proteins affects the charges of the entrances to the tunnel, the length of the tunnel and its hydrophobicity. We suggest that these structural and sequential differences influence the ligand-binding abilities of these proteins and provide sand flies with a greater number of YRP paralogs with more nuanced answers to bioamines. All these characteristics allow us to better evaluate these proteins with respect to their potential use as part of anti-Leishmania vaccines or as an antigen to measure host exposure to sand flies.

Effect of Natural Sand Percentages on Fatigue Life of Asphalt Concrete Mixture

Directory of Open Access Journals (Sweden)

Nahla Yassub Ahmed

2016-03-01

Full Text Available The design of a flexible pavement requires the knowledge of the material properties which are characterized by stiffness and fatigue resistance. The fatigue resistance relates the number of load cycles to failure with the strain level applied to the asphalt mixture. The main objective of this research is the evaluation of the fatigue life of asphalt mixtures by using two types of fine aggregate having different percentages. In this study, two types of fine aggregate were used natural sand (desert sand and crushed sand. The crushed sand was replaced by natural sand (desert sand with different percentages (0%, 25%, 75% and 100% by the weight of the sand (passing sieve No.8 and retained on sieve No.200 and one type of binder (40/50 penetration from Al-Daurah refinery. The samples of beams were tested by four point bending beam fatigue test at the control strain mode (250, 500 and 750 microstrain while the loading frequency (5Hz and testing temperature (20oC according to (AASHTO T321. The experimental work showed that fatigue life (Nf and initial flexural stiffness increased when control strain decreased for asphalt mixtures. Acceptable fatigue life at 750 microstrain was obtained with asphalt concrete mixtures containing 100% crushed sand as well as asphalt concrete contained 25% natural sand. The asphalt concrete contained 100% and 75% of natural sand exhibited high fatigue life at low level of microstrain (250. The main conclusion of this study found that best proportion of natural sand to be added to an asphaltic concrete mixture is falling within the range (0% and 25% by weight of fraction (passing No.8 and retained on No.200 sieve .

A study of global sand seas

Science.gov (United States)

McKee, Edwin D.

1979-01-01

The birth of the idea that led to this publication on "Global Sand Seas" dates back to the late 1920's. At that time I was engaged in a study of the Coconino Sandstone of Arizona's Grand Canyon. Considerable controversy existed then as to whether this sandstone was a subaqueous deposit or was composed of wind-formed dunes. It became apparent that definitive literature was sparse or lacking on types of dunes, global distribution of these types, the mechanics of their development, the precise nature of their internal structure of cross-stratificiation, and the relation of wind systems to these sand forms. Especially lacking were data on criteria that could confidently be used in the recognition of ancient dunes. The common denominator in this publication is eolian sand bodies. Although the book is concerned primarily with desert sand seas, the subject matter is not restricted to deserts; it includes many references to deposits of coastal sand and to sand bodies in humid climates. Nor does the book deal exclusively with dunes, which, according to most definitions, involve mounds or hills. Many references are made to sand sheets, sand stringers, and other types of sand deposits that have no prominent topographic expression. All sand bodies accumulated by the action of wind are discussed. Chapters A-J of this publication are primarily topical. Chapters cover the grain texture, the color, and the structure of modern dunes and other eolian sands. Special treatment is given to the relation of wind data to dune interpretation, the evolution of form in current-deposited sand bodies as determined from experimental studies, and the discriminant analysis technique for differentiating between coastal and inland desert sands. This topical part of the publication also includes an analysis of criteria used in ancient deposits to interpret their eolian genesis and a consideration of economic application of the principles described, including a discussion of potentials and problems

Effects of Moisture Content on the Foundry Properties of Yola Natural Sand

Directory of Open Access Journals (Sweden)

Paul Aondona IHOM

2012-08-01

Full Text Available The effect of moisture content of Yola natural sand has been studied. The moisture content was varied from 1 to 9%. The effect of the moisture content on the green compression strength, green permeability and bulk density was investigated. Particle size distribution of the natural sand, the grain fineness number, average grain size, grain shape and the clay content of the natural sand were also studied. 5% moisture gave the optimum green compression strength of 118.6KN/m2. The dry compression strength increased with moisture content, an optimum value of 4000KN/m2 was obtained at 9% moisture. The Yola natural sand had a grain fineness number of 88.05AFS, average grain size of 335.78 microns and a clay content of 26%. A sand mixture containing 5% moisture was prepared and used to produce a test casting with aluminium scraps, the test casting was sound.

Life cycle energy and greenhouse gas emissions from transportation of Canadian oil sands to future markets

International Nuclear Information System (INIS)

Tarnoczi, Tyler

2013-01-01

Oil sands transportation diversification is important for preventing discounted crude pricing. Current life cycle assessment (LCA) models that assess greenhouse gas (GHG) emissions from crude oil transportation are linearly-scale and fail to account for project specific details. This research sets out to develop a detailed LCA model to compare the energy inputs and GHG emissions of pipeline and rail transportation for oil sands products. The model is applied to several proposed oils sands transportation routes that may serve as future markets. Comparison between transportation projects suggest that energy inputs and GHG emissions show a high degree of variation. For both rail and pipeline transportation, the distance over which the product is transported has a large impact on total emissions. The regional electricity grid and pump efficiency have the largest impact on pipeline emissions, while train engine efficiency and bitumen blending ratios have the largest impact on rail transportation emissions. LCA-based GHG regulations should refine models to account for the range of product pathways and focus efforts on cost-effective emission reductions. As the climate-change impacts of new oil sands transportation projects are considered, GHG emission boundaries should be defined according to operation control. -- Highlights: •A life cycle model is developed to compare transportation of oil sands products. •The model is applied to several potential future oil sands markets. •Energy inputs and GHG emissions are compared. •Model inputs are explored using sensitivity analysis. •Policy recommendations are provided

Influence of the Reclaim from the Cordis Technology on the Core Sand Strength

Directory of Open Access Journals (Sweden)

Dańko J.

2014-12-01

Full Text Available The investigation results of the mechanical reclamation of spent moulding sands from the Cordis technology are presented in the paper. The quality assessment of the obtained reclaim and the influence of the reclaim fraction in a matrix on the core sand strength is given. The reclaim quality assessment was performed on the basis of the determination of losses on ignition, Na2O content on reclaim grains and pH values. The reclaim constituted 100%, 75% and 50% of the core sand matrix, for which the bending strength was determined. The matrix reclamation treatment was performed in the experimental rotor reclaimer RD-6. Spent sands were applied in as-delivered condition and after the heating to a temperature of 140 °C. Shaped samples for strength tests were made by shooting and hardening of sands in the warmbox technology.

Numerical simulation of wind-sand movement in the reversed flow region of a sand dune with a bridge built downstream.

Science.gov (United States)

He, Wei; Huang, Ning; Xu, Bin; Wang, Wenbo

2018-04-23

A bridge built inside the reversed flow region of a sand dune will change the characteristics of wind-sand movement in this region. The Reynolds-averaged Navier-Stokes simulation and discrete particle tracing are used to simulate the wind-sand movement around a sand dune with a bridge built inside the reversed region. Three cases with different bridge positions are studied. The results show that 1) compared with the isolated dune case, a tall bridge built at the leeward toe leads to an increase in the deposition rate on the leeward slope and a longer reversed flow region downstream of the sand dune; meanwhile, the high speed of crosswind on the bridge indicates that some measures should be taken to protect trains from strong crosswind; 2) a low bridge at the leeward toe has little effect on the sand deposition and reversed flow region of the dune; however, low sand transport rate and crosswind speed on the bridge show that anti-crosswind/sand measures should be taken according to the actual situation and 3) a low bridge on the leeward slope has little effect on the length of reversed flow region, however, high crosswind speed and sand flux on the bridge reveal the need of anti-crosswind/sand measures on the bridge. Moreover, the bridges in the reversed flow region increase the sand flux near the leeward crest; as a result, the moving patterns of the sand dune are changed.

Physical properties of sand parts produced using a Voxeljet VX1000 three-dimensional printer

Directory of Open Access Journals (Sweden)

Nyembwe, Kasongo

2016-11-01

Full Text Available Successful case studies of metal casting applications using sand moulds and cores produced by additive manufacturing (AM processes have been widely reported in the literature. The layered- based manufacturing process has revolutionised traditional sand moulding methods. This is essentially due to the numerous advantages of AM, including the reduction of design lead time and the ability to manufacture objects with complex geometry in a rapid turnaround time. Locally-available AM processes that are capable of producing sand moulds and cores include laser sintering (LS and three-dimensional printing (3DP, with the latter AM process growing in dominance over the former. However, a better understanding of the properties of parts produced by AM processes is required in order for the processes to be fully adopted by the foundry industry. Crucial characteristics of 3DP sand parts related to strength, dimensional accuracy, and hardness are not well- known in terms of their magnitude and in comparison with conventionally-moulded sand parts. In this investigation, the physical properties of test specimens produced under standard manufacturing conditions, using a Voxeljet VX1000 machine, were assessed for bend and tensile strength, hardness, friability, and surface finish. The physical properties of the 3DP test specimens were then compared with the properties of laboratory hand- rammed test specimens. The results of the investigation suggest that the properties of AM-fabricated sand parts are inferior to sand parts produced by conventional moulding processes.

Use of a sedimentological technique for assessing the engineering performance of sands in roads

CSIR Research Space (South Africa)

Paige-Green, P

2011-07-01

Full Text Available Although sands cover vast areas of southern Africa, their use as road materials in an untreated state has been generally avoided. An investigation into the properties of various sands has indicated, however, that they can be used as subbase...

Sand dune tracking from satellite laser altimetry

Science.gov (United States)

Dabboor, Mohammed

Substantial problems arise from sand movement in arid and semi-arid countries. Sand poses a threat to infrastructure, agricultural and urban areas. These issues are caused by the encroachment of sand on roads and railway tracks, farmland, towns and villages, and airports, to name a few. Sand movement highly depends on geomorphology including vegetation cover, shape and height of the terrain, and grain size of the sand. However, wind direction and speed are the most important factors that affect efficient sand movement. The direction of the movement depends on the main direction of the wind, but it has been shown that a minimum wind speed is required, e.g. wind gusts, to initiate sand transport. This fact prevents a simple calculation of sand transport from conventional wind data as wind records rarely contain sub-minute intervals masking out any wind gusts. An alternative of predicting sand transport is the direct observation of sand advance by in situ measurements or via satellite. Until recently, satellite imagery was the only means to compare dune shape and position for predicting dune migration over several years. In 2003, the NASA laser altimetry mission ICESat became operational and monitors elevations over all surface types including sand dunes with an accuracy of about 10-20 cm. In this study, ICESat observations from repeat tracks (tracks overlapping eachother within 50 m) are used to derive sand dune advance and direction. The method employs a correlation of the elevation profiles over several dunes and was sucessfully validated with synthetic data. The accuracy of this method is 5 meters of dune advance. One of the most active areas exhibiting sand and dune movement is the area of the Arabian Peninsula. Approximately one-third of the Arabian Peninsula is covered by sand dunes. Different wind regimes (Shamal, Kaus) cause sand dune movement in the selected study area in the eastern part of the Arabian Peninsula between 20-25 degrees North and 45-55 degrees

Experimental Study on Unconfined Compressive Strength of Organic Polymer Reinforced Sand

Directory of Open Access Journals (Sweden)

Jin Liu

2018-01-01

Full Text Available The natural sand is loose in structure with a small cohesive force. Organic polymer can be used to reinforce this sand. To assess the effectiveness of organic polymer as soil stabilizer (PSS, a series of unconfined compressive strength tests have been performed on reinforced sand. The focus of this study was to determine a curing method and a mix design to stabilize sand. The curing time, PSS concentration, and sand density were considered as variables in this study. The reinforcement mechanism was analyzed with images of scanning electron microscope (SEM. The results indicated that the strength of stabilized sand increased with the increase in the curing time, concentration, and sand density. The strength plateaus are at about curing time of 48 h. The UCS of samples with density of 1.4 g/cm3 at 10%, 20%, 30%, 40%, and 50% PSS concentration are 62.34 kPa, 120.83 kPa, 169.22 kPa, 201.94 kPa, and 245.28 kPa, respectively. The UCS of samples with PSS concentration of 30% at 1.4 g/cm3, 1.5 g/cm3, and 1.6 g/cm3 density are 169.22 kPa, 238.6 kPa 5, and 281.69 kPa, respectively. The chemical reaction between PSS and sand particle is at its microlevel, which improves the sand strength by bonding its particles together and filling the pore spaces. In comparison with the traditional reinforcement methods, PSS has the advantages of time saving, lower cost, and better environment protection. The research results can be useful for practical engineering applications, especially for reinforcement of foundation, embankment, and landfill.

Centennial review-forecast--oil sands, shales spar for markets

Energy Technology Data Exchange (ETDEWEB)

Pamenter, C B

1967-09-01

The relationship between possible developments of tar sands and oil shale deposits to the future of the oil and gas industry is examined. The Athabasca tar sands are estimated to contain 85 billion bbl of synthetic crude oil which can be exploited using currently available mining equipment and proven techniques. Another 240 billion bbl of synthetic crude are potentially available through in-situ extraction methods. Great Canadian Oil Sands Ltd. is using an extraction procedure which involves a surface mining operation, extraction and processing of the bitumen, and product shipments via a 266-mile pipeline. This procedure will be used to produce 45,000 bpd of synthetic crude and 300 ton per day of sulfur. Syncrude Canada Ltd. and Shell Canada Ltd. both have applied to the Alberta government for permission to operate 100,000-bpd operations. Syncrudes is a mining operation and Shell plans to use in-situ extraction. A number of companies have conducted research projects concerning shale oil recovery. The majority of these projects have been aimed at improving mining operations. In-situ retorting of kerogen and extraction of oil has also received consideration.

Market opportunities and challenges for oil sands

International Nuclear Information System (INIS)

Wise, T.H.

2004-01-01

The use of Alberta bitumen as a clean fuel depends on upgrading, transportation, and refining processes. Forecasts show that oil sands production, which includes synthetic crude oil (SCO), will surpass declining conventional production from the Western Canada Sedimentary Basin. The challenges facing the oils sands processing industry include: crude oil prices which affect the producer's market; market expansion options; diluent availability/cost; supply cost competitiveness; and, regional processing. The common market issues include light/heavy crude prices, oil sands crude qualities, prices of oil sands crudes, pipeline infrastructure, and competitive supplies. The issues facing the refiners are: refining margins, security of crude supply, refined product quality, and competitive product supply. It was noted that Alberta must retain or increase its share of the Midwest market. The market expansion options were reviewed for both downstream (refining) and upstream (upgrading) operations. New pipeline capacity is needed to reach more distant markets such as Southern Midwest, Washington, and California. The market is nearly saturated for Canada's heavy oil supply. More upgrading will be required as bitumen production increases. Market growth is still possible for Canada's SCO but according to forecasts, the market could also become saturated. To increase demand and allow supplies to grow, SCO prices may fall below light crude prices. It was noted that a balance must be achieved in order for producers to increase production and for refiner/upgraders to expand their conversion capacity. 13 figs

Cemented Backfilling Technology of Paste-Like Based on Aeolian Sand and Tailings

Directory of Open Access Journals (Sweden)

Qinli Zhang

2016-12-01

Full Text Available Aeolian sand, tailings, and #32.5 Portland cement were used to produce backfilling aggregate, and physicochemical evaluations and proportioning tests were conducted. It is revealed that a mixture of aeolian sand and tailings can be used as a backfilling aggregate for the complementarities of their physicochemical properties; e.g., high Al2O3 content in the aeolian sand and CaO content in the tailings, coarse particles of aeolian sand and fine particles of tailings, etc. In addition, the optimal backfilling aggregate was shown to have a mass fraction of 72%–74%, a cement–sand ratio of 1:8, and an aeolian sand proportion of 25%. Furthermore, viscometer tests were used to analyze the rheological characteristics, and the slurry in these optimized proportions exhibited shear thinning phenomena with an initial yield stress, which belongs to paste-like—a cemented backfilling slurry with a higher mass fraction than a two-phase flow and better flowability than a paste slurry. Finally, the application of this backfilling technology shows that it can not only realize safe mining, but also bring huge economic benefits, and has some constructive guidance for environmental protection.

Faunistic assemblages of a sublittoral coarse sand habitat of the northwestern Mediterranean

Directory of Open Access Journals (Sweden)

Eva Pubill

2011-02-01

Full Text Available The sublittoral megabenthic assemblages of a northwestern Mediterranean coarse sandy beach exploited for the bivalve Callista chione were studied. The spatial and bathymetric variability of its distinctive faunal assemblages was characterised by quantitative sampling performed with a clam dredge. The taxa studied were Mollusca Bivalvia and Gastropoda, Crustacea Decapoda, Echinodermata and Pisces, which accounted for over 99% of the total biomass. Three well-differentiated species assemblages were identified: (1 assemblage MSS (Medium Sand Shallow in medium sand (D50=0.37 mm and shallow waters (mean depth =6.5 m, (2 assemblage CSS (Coarse Sand Shallow in coarse sand (D50=0.62 mm in shallow waters (mean depth =6.7 m, and (3 assemblage CSD (Coarse Sand Deep in coarse sand (D50=0.64 mm in deeper waters (mean depth =16.2 m. Assemblage MSS was characterised by the codominance of the bivalves Mactra stultorum and Acanthocardia tuberculata. C. chione was dominant in both density and biomass in assemblages CSS and CSD. The occurrence of the crab Thia scutellata also characterised assemblage CSS, whereas the occurrence of the sea urchin Echinocardium mediterraneum characterised assemblage CSD. A depth breaking point of around 10 m determined the discontinuity between assemblages CSS and CSD, which was related to the closure depth of the beaches in the study area. Species richness was highest in the coarse sand communities; however, Shannon-Wiener diversity and Pielou equitability indexes were higher in the shallow fine sand community.

Habitat analysis of North American sand flies near veterans returning from leishmania-endemic war zones

Directory of Open Access Journals (Sweden)

Keep Lisa

2008-12-01

Full Text Available Abstract Background Nearly 1300 cases of leishmaniasis have been identified in American military personnel deployed to Iraq and Afghanistan. The symptoms of this disease can range from a mild, self-limiting cutaneous infection to a deadly visceral infection and are not prevented by chemoprophylaxis or immunization. Effective treatments, however, are available. The disease-causing parasite is spread through the bite of the female sand fly. Although the disease occurs in both the Old World and the New World, the parasite species differ between the hemispheres. The large number of cases in military veterans has caused some concern that Old World, temperate-adapted parasite species could be introduced into the native sand fly populations of American military facilities where veterans of the current conflicts return following their deployments. This paper reports part of a larger study to analyze the risk of such an accidental importation. Four potential habitats on two large Army facilities in the Southeast United States were surveyed to determine relative sand fly density. The National Land Cover Map was used to provide sand fly density prediction maps by habitat. Results Sand fly density was significantly higher in deciduous forest and even higher at the interface between forest and open grassland. The evergreen forest and agricultural fields supported very low densities. On Fort Campbell, KY, the percentage of land covered by suitable habitat was very high. A sand fly density prediction map identified large tracts of land where infected individuals would be at higher risk of exposure to sand fly bites, resulting in an increased risk of introducing the parasite to a native insect population. On Fort Bragg, NC, however, commercial farming of long leaf pine reduced the percentage of the land covered in vegetation suitable for the support of sand flies. The risk of introducing an exotic Leishmania spp. on Fort Bragg, therefore, is considered to be

Experimental investigation on high performance RC column with manufactured sand and silica fume

Science.gov (United States)

Shanmuga Priya, T.

2017-11-01

In recent years, the use High Performance Concrete (HPC) has increased in construction industry. The ingredients of HPC depend on the availability and characteristics of suitable alternative materials. Those alternative materials are silica fume and manufactured sand, a by products from ferro silicon and quarry industries respectively. HPC made with silica fume as partial replacement of cement and manufactured sand as replacement of natural sand is considered as sustainable high performance concrete. In this present study the concrete was designed to get target strength of 60 MPa as per guide lines given by ACI 211- 4R (2008). The laboratory study was carried out experimentally to analyse the axial behavior of reinforced cement HPC column of size 100×100×1000mm and square in cross section. 10% of silica fume was preferred over ordinary portland cement. The natural sand was replaced by 0, 20, 40, 60, 80 and 100% with Manufactured Sand (M-Sand). In this investigation, totally 6 column specimens were cast for mixes M1 to M6 and were tested in 1000kN loading frame at 28 days. From this, Load-Mid height deflection curves were drawn and compared. Maximum ultimate load carrying capacity and the least deflection is obtained for the mix prepared by partial replacement of cement with 10% silica fume & natural sand by 100% M-Sand. The fine, amorphous and pozzalonic nature of silica fume and fine mineral particles in M- Sand increased the stiffness of HPC column. The test results revealed that HPC can be produced by using M-Sand with silica fume.

Microbial pesticide removal in rapid sand filters for drinking water treatment – Potential and kinetics

DEFF Research Database (Denmark)

Hedegaard, Mathilde Jørgensen; Albrechtsen, Hans-Jørgen

2014-01-01

Filter sand samples, taken from aerobic rapid sand filters used for treating groundwater at three Danish waterworks, were investigated for their pesticide removal potential and to assess the kinetics of the removal process. Microcosms were set up with filter sand, treated water, and the pesticides...... or metabolites mecoprop (MCPP), bentazone, glyphosate and p-nitrophenol were applied in initial concentrations of 0.03–2.4 μg/L. In all the investigated waterworks the concentration of pesticides in the water decreased – MCPP decreased to 42–85%, bentazone to 15–35%, glyphosate to 7–14% and p-nitrophenol 1....../L) increased from 0.21%/g filter sand to 0.75%/g filter sand, when oxygen availability was increased from 0.28 mg O2/g filter sand to 1.09 mg O2/g filter sand. Bentazone was initially cleaved in the removal process. A metabolite, which contained the carbonyl group, was removed rapidly from the water phase...

Use of Crushed Granite Fine as Replacement to River Sand in Concrete Production

Directory of Open Access Journals (Sweden)

Manasseh JOEL

2010-12-01

Full Text Available The suitability of Crushed granite fine (CGF to replace river sand in concrete production for use in rigid pavement was investigated. Slump, compressive and indirect tensile strength tests were performed on fresh and hardened concrete.28 days Peak compressive and indirect tensile strength values of 40.70N/mm2 and 2.30N/mm2 respectively was obtained, with the partial replacement of river sand with 20% CGF, as against values of 35.00N/mm2 and 1.75N/mm2, obtained with the use of river sand as fine aggregate. Based on economic analysis and results of tests, river sand replaced with 20% CGF is recommended for use in the production of concrete for use in rigid pavement. Conservation of river sand in addition to better ways of disposing wastes from the quarry sites are some of the merits of using CGF.

Mineral Resource Assessment of Marine Sand Resources in Cape- and Ridge-Associated Marine Sand Deposits in Three Tracts, New York and New Jersey, United States Atlantic Continental Shelf

Science.gov (United States)

Bliss, James D.; Williams, S. Jeffress; Arsenault, Matthew A.

2009-01-01

Demand is growing in the United States and worldwide for information about the geology of offshore continental shelf regions, the character of the seafloor, and sediments comprising the seafloor and subbottom. Interest in locating sand bodies or high quality deposits that have potential as sources for beach nourishment and ecosystem restoration is especially great in some regions of the country. The Atlantic coast, particularly New York and New Jersey, has been the focus of these studies for the past 40 years with widely varying results. This study is the first attempt at applying probability statistics to modeling Holocene-age cape-and ridge-associated sand deposits and thus focuses on distinct sand body morphology. This modeling technique may have application for other continental shelf regions that have similar geologic character and late Quaternary sea-level transgression history. An estimated volume of 3.9 billion m3 of marine sand resources is predicted in the cape-and ridge-associated marine sand deposits in three representative regions or tracts on the continental shelf offshore of New York and New Jersey. These estimates are taken from probabilistic distributions of sand resources and are produced using deposit models and Monte Carlo Simulation (MCS) techniques. The estimated sand resources presented here are for only three tracts as described below and for Holocene age sand resources contained in cape-and ridge-associated marine sand deposit types within this area. Other areas may qualify as tracts for this deposit type and other deposit types and geologic ages (for example, paleo-stream channels, blanket and outwash deposits, ebb-tide shoals, and lower sea level-stand deltas), which are present on the New Jersey and New York continental shelf area but are not delineated and modeled in this initial evaluation. Admittedly, only a portion of these probable sand resources will ultimately be available and suitable for production, dependent largely on

Microbial processes in the Athabasca Oil Sands and their potential applications in microbial enhanced oil recovery.

Science.gov (United States)

Harner, N K; Richardson, T L; Thompson, K A; Best, R J; Best, A S; Trevors, J T

2011-11-01

The Athabasca Oil Sands are located within the Western Canadian Sedimentary Basin, which covers over 140,200 km(2) of land in Alberta, Canada. The oil sands provide a unique environment for bacteria as a result of the stressors of low water availability and high hydrocarbon concentrations. Understanding the mechanisms bacteria use to tolerate these stresses may aid in our understanding of how hydrocarbon degradation has occurred over geological time, and how these processes and related tolerance mechanisms may be used in biotechnology applications such as microbial enhanced oil recovery (MEOR). The majority of research has focused on microbiology processes in oil reservoirs and oilfields; as such there is a paucity of information specific to oil sands. By studying microbial processes in oil sands there is the potential to use microbes in MEOR applications. This article reviews the microbiology of the Athabasca Oil Sands and the mechanisms bacteria use to tolerate low water and high hydrocarbon availability in oil reservoirs and oilfields, and potential applications in MEOR.

PCE and BNS admixture adsorption in sands with different composition and particle size distribution

International Nuclear Information System (INIS)

Alonso, M.M.; Martínez-Gaitero, R.; Gismera-Diez, S.; Puertas, F.

2017-01-01

The choice of a superplasticiser (SP) for concrete is of great complexity, as it is well known that properties of the end product are related to admixture and its compatibility with concrete components. Very few studies have been conducted on the compatibility between SPs and the sand of mortars and concretes, however. Practical experience has shown that sand fineness and mineralogical composition affect water demand and admixture consumption. Clay-containing sand has been found also to adsorb SPs, reducing the amount available in solution for adsorption by the cement. This study analysed the isotherms for PCE and BNS superplasticiser adsorption on four sands with different fineness and compositions commonly used to prepare mortars and concretes. BNS-based SP did not adsorb on sands, while PCE-based admixtures exhibited variable adsorption depending on different factors. The adsorption curves obtained revealed that the higher the sand fineness, the finer the particle size distribution and the higher the clay material, the greater was PCE admixture adsorption/ consumption. [es

bentonite-sand mixture as new backfill/buffer material

International Nuclear Information System (INIS)

Cui Suli; Liu Jisheng; Zhang Huyuan; Liang Jian

2008-01-01

The mixture of bentonite and quartz sand is suggested as a new backfill/buffer material for geological disposal of HLW. To improve the further design of underground laboratory and in-situ industrial construction test, the optimization of sand addition to bentonite is focused at present research stage. Based on summarizing the research results abroad, laboratory tests were conducted on the mixture of GMZ001 bentonite and quartz sand, such as compaction test and swelling tests etc. Test data shows that GMZ bentonite-sand mixture exhibits a favorite compaction with a 30% sand addition, a highest swelling pressure with a 20% sand addition, and a decreasing plasticity with increases in sand addition and pore liquid concentration. (authors)

Comparison between predicted and observed sand waves and sand banks in the North Sea

NARCIS (Netherlands)

Hulscher, Suzanne J.M.H.; van den Brink, G.M.

2001-01-01

For the first time a prediction model of regular morphological patterns on the seabed was tested against observations of sand wave and sand bank occurrence in the entire North Sea. The model, which originates from first physical principles, predicts this occurrence via two dimensionless parameters

Shear strength properties of naturally occurring bituminous sands

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2009-06-01

Full Text Available because of the cohesive nature of bitumen contents. However, results from the direct shear tests were comparable to properties of oil sands reported earlier from various other laboratory tests. Based on the direct shear test results, Mohr-Coulomb failure...

Critical State of Sand Matrix Soils

Science.gov (United States)

Marto, Aminaton; Tan, Choy Soon; Makhtar, Ahmad Mahir; Kung Leong, Tiong

2014-01-01

The Critical State Soil Mechanic (CSSM) is a globally recognised framework while the critical states for sand and clay are both well established. Nevertheless, the development of the critical state of sand matrix soils is lacking. This paper discusses the development of critical state lines and corresponding critical state parameters for the investigated material, sand matrix soils using sand-kaolin mixtures. The output of this paper can be used as an interpretation framework for the research on liquefaction susceptibility of sand matrix soils in the future. The strain controlled triaxial test apparatus was used to provide the monotonic loading onto the reconstituted soil specimens. All tested soils were subjected to isotropic consolidation and sheared under undrained condition until critical state was ascertain. Based on the results of 32 test specimens, the critical state lines for eight different sand matrix soils were developed together with the corresponding values of critical state parameters, M, λ, and Γ. The range of the value of M, λ, and Γ is 0.803–0.998, 0.144–0.248, and 1.727–2.279, respectively. These values are comparable to the critical state parameters of river sand and kaolin clay. However, the relationship between fines percentages and these critical state parameters is too scattered to be correlated. PMID:24757417

High-temperature expansion and knock-out properties of moulding sands with water glass

Directory of Open Access Journals (Sweden)

Major-Gabryś K.

2007-01-01

Full Text Available The article focuses on the topic of improving the knock-out properties of moulding sand with water glass and ester hardener. It is settled that the cause of worse knock-out properties of moulding sand can be brought by their thermal expansion in increased temperatures. There is a presentation of the influence of different additives, containing Al2O3, on moulding sands’ expansion in increased temperatures. Within the frames of research, there was an elaboration of the influence of authors own additive- Glassex, on the expansion phenomenon of moulding sands with water glass and ester hardener. It is concluded, that the new additive stops the expansion of moulding sands and as well it improves their knock-out properties.

Behavior of Hollow Thin Welded Tubes Filled with Sand Slag Concrete

Directory of Open Access Journals (Sweden)

Noureddine Ferhoune

2016-01-01

Full Text Available This paper presents the axial bearing capacity of thin welded rectangular steel stubs filled with concrete sand. A series of tests was conducted to study the behavior of short composite columns under axial compressive load; the cross section dimensions were 100 × 70 × 2 mm. A total of 20 stubs have been tested, as follows: 4 hollow thin welded tubes were tested to axial and eccentric load compression, 4 were filled with ordinary concrete appointed by BO columns, 6 were filled with concrete whose natural sand was completely substituted by a crystallized sand slag designated in this paper by BSI, and 6 were tucked in concrete whose natural sand was partially replaced by a crystallized sand slag called BSII. The main parameters studied are the height of the specimen (300 mm–500 mm, eccentricity of load and type of filling concrete. Based on test results obtained, it is confirmed that the length of the tubes has a considerable effect on the bearing capacity and the failure mode. In all test tubes, fracture occurred by the convex local buckling of steel section due to the outward thrust of the concrete; it was observed that the sand concrete improves the bearing capacity of tubes compounds compared to those filled with ordinary concrete.

Production and global transport of Titan's sand particles

Science.gov (United States)

Barnes, Jason W.; Lorenz, Ralph D.; Radebaugh, Jani; Hayes, Alexander G.; Arnold, Karl; Chandler, Clayton

2015-06-01

Previous authors have suggested that Titan's individual sand particles form by either sintering or by lithification and erosion. We suggest two new mechanisms for the production of Titan's organic sand particles that would occur within bodies of liquid: flocculation and evaporitic precipitation. Such production mechanisms would suggest discrete sand sources in dry lakebeds. We search for such sources, but find no convincing candidates with the present Cassini Visual and Infrared Mapping Spectrometer coverage. As a result we propose that Titan's equatorial dunes may represent a single, global sand sea with west-to-east transport providing sources and sinks for sand in each interconnected basin. The sand might then be transported around Xanadu by fast-moving Barchan dune chains and/or fluvial transport in transient riverbeds. A river at the Xanadu/Shangri-La border could explain the sharp edge of the sand sea there, much like the Kuiseb River stops the Namib Sand Sea in southwest Africa on Earth. Future missions could use the composition of Titan's sands to constrain the global hydrocarbon cycle.

The influence of microwave heating and water glass kind on the properties of molding sands

Directory of Open Access Journals (Sweden)

K. Granat

2008-03-01

Full Text Available This work presents rcsults of research on thc influcncc of microwave heating time on the process of hardening of warcr glass moldingsands. Essential influence of this drying process on basic properties such as: cornprcssion, bcnding mind tcnsitc strcng~h as well aspcrrneabili~y and war resistance, has bccn found. It has bccn proved, that at1 thc investigated sorts of sodium water glass could be uscd asbinding material of molding sands intended for curing with the microwave process healing. It has bccn found, while analyzing the rcsultsof property studics or microwavc heated molding sands with 2.5% addition of water glass, that aIl available on the markct kinds of thisbinding agent (inctuding the most frequently uscd in foundry 145 and 149 kinds after microwave heating guarantee very goodcompression, bending and tensile strength as well as permeability and wcar resistance. Moroovcr, it has bccn dctcrmined that the optimalcuring powcr of molding sands containing various kinds of water gIass is 560 W. AII values exceeding this rcsult in stabilization of basicpropcrtics of molding sands. The use of microwave curing of water glass molding sands results in a significant decrease of hardeningprocess time. full stabilization of molding sands as well as much lower energy consumption.

Study of Slow Sand Filtration in Removing Total Coliforms and E.Coli

Directory of Open Access Journals (Sweden)

Ekha Yogafanny

2015-08-01

Full Text Available This study was aimed to evaluate the performance of SSF in removing bacteria (Total Coliforms and E. Coli in regard to grain size distribution and grain shape intermittently. Two methodological approaches used in this reasearch were literature review and laboratory work. Bacteria removal was analyzed considering two different filter media (Rhine sand-spherical shape and Lava sand-angular shape with three different grain size distributions. The best performance was attained by filter column F4 which consisted of Lava sand and had the configuration C2 (d10 = 0.07 mm; Cu = 4.2. This filter column achieved 4.7log-units removal of Total Coliforms and 5.0log-units removal of E. coli. The results show that a smaller grain size and an angular shape of sand grain lead to an increase in bacteria removal.

The energy efficiency of oil sands extraction: Energy return ratios from 1970 to 2010

International Nuclear Information System (INIS)

Brandt, Adam R.; Englander, Jacob; Bharadwaj, Sharad

2013-01-01

It has been argued that the oil sands industry is not energy efficient: comparatively large energy inputs are required per unit of energy output from oil sands operations. Unfortunately, quantitative work to date in this area has suffered from poor data availability and uncertain methods. We apply a new methodology and new dataset to compute ERRs (energy return ratios) for the oil sands industry. We collected monthly oil sands energy consumption and output data from 1970 to 2010. Current oil sands operations have mine mouth NERs (net energy returns) of about 6 GJ output per GJ of energy consumed and point of use energy returns of about 3 GJ/GJ. Long-term trends show oil sands operations becoming significantly more efficient: point of use NER increased from about 1 GJ/GJ in 1970 to 3 GJ/GJ in 2010. These energy returns are lower than those observed in historical conventional oil operations, but low energy returns are not likely to hinder development of oil sands operations due to the large resource in place and the ability for largely self-fueled pathways to return significant amounts of energy to society for every unit of external energy supplied. - Highlights: • Oil sands operations have become significantly more energy efficient over the history of the industry. • Oil sands production is largely fueled with energy from the bitumen resource itself, making external energy returns high. • Oil sands production is still significantly less efficient than conventional oil production

Sand to Root Transfer of PAHs and PCBs by Carrots Grown on Sand with Pure Substances and Biosolids Amended Sand

OpenAIRE

Sablayrolles, Caroline; Montréjaud-Vignoles, Mireille; Silvestre, Jérôme; Patria, Lucie

2006-01-01

A study on behaviour of trace organic compounds (Polycyclic Aromatic Hydrocarbons, PAH, and Polychlorinated Biphenyls, PCB) in a sand-plant system has been carried out, with the reclamation of wastewater treatment plant biosolids for agriculture in mind. Carrot plants (Daucus carota) were grown on soilless culture (sand), to provide optimal transfer conditions, in plant containers inside a temperature regulated greenhouse. There were two types of experiment. The trace organic compounds have i...

3D Finite Element Analysis of PWA-Oil Sand Terrain System Interaction

Directory of Open Access Journals (Sweden)

Y. Li

2012-01-01

Full Text Available A simulator for analyzing the interaction between the oil sand terrain and a pipe wagon articulating (PWA system has been developed in this paper. An elastic-plastic oil sand model was built based on the finite element analysis (FEA method and von Mises yield criterion using the Algor mechanical event simulation (MES software. The three-dimensional (3D distribution of the stress, strain, nodal displacement, and deformed shape of the oil sands was animated at an environmental temperature of 25°C. The 3D behavior of the oil sand terrain was investigated with different loading conditions. The effect of the load and contact area on the stress and nodal displacement was analyzed, respectively. The results indicate that both the max stress and max nodal displacement increase with the load varying from 0 to 3.6+7 N and decrease with the contact area varying from 2 to 10 m2. The method presented in this paper forms the basis for evaluating the bearing capacity of oil sand ground.

René Sand (Belgium, President 1946 – 1953

Directory of Open Access Journals (Sweden)

2008-07-01

Full Text Available The extraordinary significance of the life and work of René Sand lies in his central position as a mediator, promoter and coordinator of social work on an increasingly international level during the interwar-period and it can hardly be overestimated.

Effect of part replacement of silica sand with carbon black on composite properties

International Nuclear Information System (INIS)

Adeosun, B.F.; Olaofe, O.

2003-01-01

We have reported the properties of natural rubber filled with locally available materials (Adu et al 2000). The effect of local clay, limestone, silica sand and charcoal on the properties of natural rubber has been examined. Results have shown detrimental effects of silica sand on the properties of natural rubber compound. It has been reported that when silica is used as a part for part replacement of carbon black, the heat build up the composite decreased whilst tear resistance improved. Results revealed that within the filler content range used in the present work, the hardness, modulus, and tensile strength of composites loaded with silica sand/carbon black showed enhanced magnitude over the composite loaded singly with silica sand. These parameters generally increased with increasing carbon black content in the composite. New area of use requiring moderate level of tensile strength, hardness and modulus (as in soles of shoes and engine mounts) is therefore opened up for silica sand.(author)

Frac Sand Mines Are Preferentially Sited in Unzoned Rural Areas.

Directory of Open Access Journals (Sweden)

Christina Locke

Full Text Available Shifting markets can cause unexpected, stochastic changes in rural landscapes that may take local communities by surprise. Preferential siting of new industrial facilities in poor areas or in areas with few regulatory restrictions can have implications for environmental sustainability, human health, and social justice. This study focuses on frac sand mining-the mining of high-quality silica sand used in hydraulic fracturing processes for gas and oil extraction. Frac sand mining gained prominence in the 2000s in the upper midwestern United States where nonmetallic mining is regulated primarily by local zoning. I asked whether frac sand mines were more commonly sited in rural townships without formal zoning regulations or planning processes than in those that undertook zoning and planning before the frac sand boom. I also asked if mine prevalence was correlated with socioeconomic differences across townships. After creating a probability surface to map areas most suitable for frac sand mine occurrence, I developed neutral landscape models from which to compare actual mine distributions in zoned and unzoned areas at three different spatial extents. Mines were significantly clustered in unzoned jurisdictions at the statewide level and in 7 of the 8 counties with at least three frac sand mines and some unzoned land. Subsequent regression analyses showed mine prevalence to be uncorrelated with land value, tax rate, or per capita income, but correlated with remoteness and zoning. The predicted mine count in unzoned townships was over two times higher than that in zoned townships. However, the county with the most mines by far was under a county zoning ordinance, perhaps indicating industry preferences for locations with clear, homogenous rules over patchwork regulation. Rural communities can use the case of frac sand mining as motivation to discuss and plan for sudden land-use predicaments, rather than wait to grapple with unfamiliar legal processes

Coastal geology and recent origins for Sand Point, Lake Superior

Science.gov (United States)

Fisher, Timothy G.; Krantz, David E.; Castaneda, Mario R.; Loope, Walter L.; Jol, Harry M.; Goble, Ronald J.; Higley, Melinda C.; DeWald, Samantha; Hansen, Paul

2014-01-01

Sand Point is a small cuspate foreland located along the southeastern shore of Lake Superior within Pictured Rocks National Lakeshore near Munising, Michigan. Park managers’ concerns for the integrity of historic buildings at the northern periphery of the point during the rising lake levels in the mid-1980s greatly elevated the priority of research into the geomorphic history and age of Sand Point. To pursue this priority, we recovered sediment cores from four ponds on Sand Point, assessed subsurface stratigraphy onshore and offshore using geophysical techniques, and interpreted the chronology of events using radiocarbon and luminescence dating. Sand Point formed at the southwest edge of a subaqueous platform whose base is probably constructed of glacial diamicton and outwash. During the post-glacial Nipissing Transgression, the base was mantled with sand derived from erosion of adjacent sandstone cliffs. An aerial photograph time sequence, 1939–present, shows that the periphery of the platform has evolved considerably during historical time, infl uenced by transport of sediment into adjacent South Bay. Shallow seismic refl ections suggest slump blocks along the leading edge of the platform. Light detection and ranging (LiDAR) and shallow seismic refl ections to the northwest of the platform reveal large sand waves within a deep (12 m) channel produced by currents fl owing episodically to the northeast into Lake Superior. Ground-penetrating radar profi les show transport and deposition of sand across the upper surface of the platform. Basal radiocarbon dates from ponds between subaerial beach ridges range in age from 540 to 910 cal yr B.P., suggesting that Sand Point became emergent during the last ~1000 years, upon the separation of Lake Superior from Lakes Huron and Michigan. However, optically stimulated luminescence (OSL) ages from the beach ridges were two to three times as old as the radiocarbon ages, implying that emergence of Sand Point may have begun

An Investigation into the Use of Manufactured Sand as a 100% Replacement for Fine Aggregate in Concrete

Directory of Open Access Journals (Sweden)

Martins Pilegis

2016-06-01

Full Text Available Manufactured sand differs from natural sea and river dredged sand in its physical and mineralogical properties. These can be both beneficial and detrimental to the fresh and hardened properties of concrete. This paper presents the results of a laboratory study in which manufactured sand produced in an industry sized crushing plant was characterised with respect to its physical and mineralogical properties. The influence of these characteristics on concrete workability and strength, when manufactured sand completely replaced natural sand in concrete, was investigated and modelled using artificial neural networks (ANN. The results show that the manufactured sand concrete made in this study generally requires a higher water/cement (w/c ratio for workability equal to that of natural sand concrete due to the higher angularity of the manufactured sand particles. Water reducing admixtures can be used to compensate for this if the manufactured sand does not contain clay particles. At the same w/c ratio, the compressive and flexural strength of manufactured sand concrete exceeds that of natural sand concrete. ANN proved a valuable and reliable method of predicting concrete strength and workability based on the properties of the fine aggregate (FA and the concrete mix composition.

Analysis of wind-blown sand movement over transverse dunes.

Science.gov (United States)

Jiang, Hong; Huang, Ning; Zhu, Yuanjian

2014-12-01

Wind-blown sand movement often occurs in a very complicated desert environment where sand dunes and ripples are the basic forms. However, most current studies on the theoretic and numerical models of wind-blown sand movement only consider ideal conditions such as steady wind velocity, flat sand surface, etc. In fact, the windward slope gradient plays a great role in the lift-off and sand particle saltation. In this paper, we propose a numerical model for the coupling effect between wind flow and saltating sand particles to simulate wind-blown sand movement over the slope surface and use the SIMPLE algorithm to calculate wind flow and simulate sands transport by tracking sand particle trajectories. We furthermore compare the result of numerical simulation with wind tunnel experiments. These results prove that sand particles have obvious effect on wind flow, especially that over the leeward slope. This study is a preliminary study on windblown sand movement in a complex terrain, and is of significance in the control of dust storms and land desertification.

Sand lance: A review of biology and predator relations and annotated bibliography

Science.gov (United States)

Robards, Martin D.; Willson, Mary F.; Armstrong, Robert H.; Piatt, John F.

1999-01-01

Six species of sand lance (Ammodytes) in temperate and boreal regions are currently recognized. Sand lance can occupy a wide range of environmental conditions, but all appear to be dormant predominantly in winter, and one species is in summer also. They lack a swim bladder and spend much of their time buried in specific substrates. Copepods are the primary food. Spawning usually occurs in fall or winter (although some species also spawn in spring), eggs are demersal, and larvae may hatch at times of low food abundance. Sand lance usually occur in schools and are regarded as a relatively high-quality forage fish.Sand lance constitute a major prey for at least some populations of over 100 species of consumer, including 40 species of birds, 12 species of marine mammals, 45 species of fishes, and some invertebrates. Variation in the availability of sand lance (and other forage fishes) can have major effects on the breeding success and survival of their predators. Commercial fishing and other pressures on sand lance populations potentially have ramifying effects on many species of wildlife.The bibliography contains over 1,700 references on the family Ammodytidae, with an emphasis on the genus Ammodytes. Keywords are provided for each reference and have been further organized into taxonomic, geographic, subject, and predator indexes.

Growing markets to sustain oil sands development

International Nuclear Information System (INIS)

Wise, T.H.

2003-01-01

The utilization of Alberta bitumen for the clean fuels market depends on upgrading, transportation, and refining processes. Forecasts show that oil sands production, which includes synthetic crude oil (SCO), will surpass declining conventional production in Western Canada. Several issues pose a challenge to the oil sands processing industry. The producers' market is affected by crude oil prices, market expansion options, diluent availability/cost, supply cost competitiveness, and regional processing. The common market issues include light/heavy crude prices, oil sands crude qualities, prices of oil sands crudes, pipeline infrastructure, and competitive supplies. The issues facing the refiners are: refining margins, security of crude supply, refined product quality, and competitive product supply. A brief review of markets for Canadian crude oil, including synthetic crude, was provided. The share of the Midwest market by Alberta must be retained and increased. The market expansion options were reviewed for both downstream (refining) and upstream (upgrading) operations. To reach more distant markets such as Southern Midwest, Washington, and California, new pipeline capacity would be required. The market is nearly saturated for Canada's heavy oil supply. More upgrading will be required as bitumen production increases. Market growth is still possible for Canada's SCO but according to forecasts, the market could also become saturated. To increase demand and allow supplies to grow, SCO prices may fall below light crude prices. It was noted that a balance must be achieved in order for producers to increase production and for refiner/upgraders to expand their conversion capacity. tabs., figs

Sustainable use of oil sands for geotechnical construction and road building

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2012-02-01

Full Text Available of the three oil sand samples. Oil Sand ID w [%] wb [%] D10 D30 D50 D60 Cu Cc SE-09 1.4 8.5 0.07 0.12 0.17 0.19 2.9 1.17 SE-14 3.2 13.3 0.08 0.14 0.18 0.21 2.8 1.24 AU-14 2.2 14.5 0.09 0.17 0.22 0.27 3.0 1.19 w = water content; wb = bitumen content; Di... = grain size (mm) corresponding to i-percent passing by mass; Cu = coefficient of uniformity; Cc = coefficient of curvature. Sample Preparation The oil sand samples were prepared for the laboratory testing program using an Industrial Process...

Sand consolidation

Energy Technology Data Exchange (ETDEWEB)

Spain, H H

1965-01-21

In a sand consolidation method in which there is injected a mixture of resin-forming liquids comprising an aryl-hydroxy low molecular weight compound, a water- soluble aldehyde, and a catalyst, an improvement is claimed which comprises diluting the resin-forming liquids with a diluent and with water so that the yield of the resin is sufficient to consolidate the sand particles with the minimum desirable pressure. The diluent may be mutually soluble in water and in the resin-forming liquids, and does not affect the setting time of the polymer. The aldehyde and the aryl-hydroxy compound may be in ratio of 5:1, and the diluent, methyl alcohol, is present in a ratio of 2:1 with reference to the water.

Sands at Gusev Crater, Mars

Science.gov (United States)

Cabrol, Nathalie A.; Herkenhoff, Kenneth E.; Knoll, Andrew H.; Farmer, Jack D.; Arvidson, Raymond E.; Grin, E.A.; Li, Ron; Fenton, Lori; Cohen, B.; Bell, J.F.; Yingst, R. Aileen

2014-01-01

Processes, environments, and the energy associated with the transport and deposition of sand at Gusev Crater are characterized at the microscopic scale through the comparison of statistical moments for particle size and shape distributions. Bivariate and factor analyses define distinct textural groups at 51 sites along the traverse completed by the Spirit rover as it crossed the plains and went into the Columbia Hills. Fine-to-medium sand is ubiquitous in ripples and wind drifts. Most distributions show excess fine material, consistent with a predominance of wind erosion over the last 3.8 billion years. Negative skewness at West Valley is explained by the removal of fine sand during active erosion, or alternatively, by excess accumulation of coarse sand from a local source. The coarse to very coarse sand particles of ripple armors in the basaltic plains have a unique combination of size and shape. Their distribution display significant changes in their statistical moments within the ~400 m that separate the Columbia Memorial Station from Bonneville Crater. Results are consistent with aeolian and/or impact deposition, while the elongated and rounded shape of the grains forming the ripples, as well as their direction of origin, could point to Ma'adim Vallis as a possible source. For smaller particles on the traverse, our findings confirm that aeolian processes have dominated over impact and other processes to produce sands with the observed size and shape patterns across a spectrum of geologic (e.g., ripples and plains soils) and aerographic settings (e.g., wind shadows).

New records of phlebotomine sand flies (Diptera: Psychodidae from Ecuador

Directory of Open Access Journals (Sweden)

J. Bruce Alexander

1992-03-01

Full Text Available The plebotomine sand fly fauna of Ecuador was surveyed in two 3-month collecting trips made in 1988 and 1990. A total of 12 provinces were visited, including three (Bolivar, Loja and Morona Santiago from wich no previous records to phlebotomines existed. Forty-six species were collected, 13 of wich, together with 1 subspecies and 1 genus (Warileya represented new records for the country. This survey increases the known number of species in Ecuador to 60. The distribuition of Ecuadorian sand flies is discussed in the light of these new findings.

Direct Chlorination of Zircon Sand

International Nuclear Information System (INIS)

Dwiretnani Sudjoko; Budi Sulistyo; Pristi Hartati; Sunardjo

2002-01-01

It was investigated the direct chlorination of zircon sand in a unit chlorination equipment. The process was in semi batch. The product gas was scrubbed in aqueous NaOH. It was search the influence of time, ratio of reactant and size of particle sand to the concentration of Zr and Si in the product. From these research it was found that as the times, ratio of reactant increased, the concentration of Zr increased, but the concentration of Si decreased, while as grain size of zircon sand decreased the concentration of Zr decreased, but the concentration of Si increased. (author)

Decontamination of Uranium-Contaminated Soil Sand Using Supercritical CO2 with a TBP–HNO3 Complex

Directory of Open Access Journals (Sweden)

Kwangheon Park

2015-09-01

Full Text Available An environmentally friendly decontamination process for uranium-contaminated soil sand is proposed. The process uses supercritical CO2 as the cleaning solvent and a TBP–HNO3 complex as the reagent. Four types of samples (sea sand and coarse, medium, and fine soil sand were artificially contaminated with uranium. The effects of the amount of the reagent, sand type, and elapsed time after the preparation of the samples on decontamination were examined. The extraction ratios of uranium in all of the four types of sand samples were very high when the time that elapsed after preparation was less than a few days. The extraction ratio of uranium decreased in the soil sand with a higher surface area as the elapsed time increased, indicating the possible formation of chemisorbed uranium on the surface of the samples. The solvent of supercritical CO2 seemed to be very effective in the decontamination of soil sand. However, the extraction of chemisorbed uranium in soil sand may need additional processes, such as the application of mechanical vibration and the addition of bond-breaking reagents.

An investigation of the potential for in situ bioremediation of oil sands tailings

International Nuclear Information System (INIS)

Herman, D.C.; Costerton, J.W.; Fedorak, P.M.; Mackinnon, M.D.

1993-01-01

Oil sand tailings water has been shown to be acutely toxic to aquatic organisms. Naphthenic acids have been shown to be the primary source of this toxicity within oil sand tailings waste. The potential for in-situ bioremediation of oil sand tailings was investigated by determining the ability of indigenous bacteria to biodegrade naphthenic acids. A mixed bacterial culture enriched from oil sand tailings was found to be capable of growth on a commercially available naphthenic acid mixture. When sodium naphthenates (30 mg/l) were added to a minimal salts medium and inoculated with the mixed bacterial culture, gas chromatography revealed that many components of the naphthenic acid mixture were biodegraded within eight days of incubation. The same culture was also tested against the naphthenic acid fraction extracted directly from oil sand tailings. The tailings extract was diluted into the minimal salts medium in sealed flasks and inoculated with the enrichment culture. The production of CO 2 indicated microbial mineralization of components within the oil sands extract. Microtox analysis determined that microbial activity resulted in a reduction in the acute toxicity of the tailings extract. 5 refs., 3 figs

Phytoremediation of Alberta oil sand tailings using native plants and fungal endophytes

Science.gov (United States)

Repas, T.; Germida, J.; Kaminskyj, S.

2012-04-01

Fungal endophytes colonize host plants without causing disease. Some endophytes confer plant tolerance to harsh environments. One such endophyte, Trichoderma harzianum strain TSTh20-1, was isolated from a plant growing on Athabasca oil sand tailings. Tailing sands are a high volume waste product from oil sand extraction that the industry is required to remediate. Tailing sands are low in organic carbon and mineral nutrients, and are hydrophobic due to residual polyaromatic hydrocarbons. Typically, tailing sands are remediated by planting young trees in large quantities of mulch plus mineral fertilizer, which is costly and labour intensive. In greenhouse trials, TSTh20-1 supports growth of tomato seedlings on tailing sands without fertilizer. The potential use of TSTh20-1 in combination with native grasses and forbs to remediate under field conditions is being assessed. Twenty-three commercially available plant species are being screened for seed germination and growth on tailing sands in the presence of TSTh20-1. The best candidates from this group will be used in greenhouse and small scale field trials. Potential mechanisms that contribute to endophyte-induced plant growth promotion, such as plant hormone production, stress tolerance, mineral solubilization, and uptake are also being assessed. As well, TSTh20-1 appears to be remarkably frugal in its nutrient requirements and the possibility that this attribute is characteristic of other plant-fungal endophytes from harsh environments is under study.

Assessment Method of Overheating Degree of a Spent Moulding Sand with Organic Binder, After the Casting Process

Directory of Open Access Journals (Sweden)

Dańko R.

2013-06-01

Full Text Available A proper management of sand grains of moulding sands requires knowing basic properties of the spent matrix after casting knocking out. This information is essential from the point of view of the proper performing the matrix recycling process and preparing moulding sands with reclaimed materials. The most important parameter informing on the matrix quality - in case of moulding sands with organic binders after casting knocking out - is their ignition loss. The methodology of estimating ignition loss of spent moulding sands with organic binder - after casting knocking out - developed in AGH, is presented in the paper. This method applies the simulation MAGMA software, allowing to determine this moulding sand parameter already at the stage of the production preparation.

Influence of core sand properties on flow dynamics of core shooting process based on experiment and multiphase simulation

Directory of Open Access Journals (Sweden)

Chang-jiang Ni

2017-03-01

Full Text Available The influence of core sand properties on flow dynamics was investigated synchronously with various core sands, transparent core-box and high-speed camera. To confirm whether the core shooting process has significant turbulence, the flow pattern of sand particles in the shooting head and core box was reproduced with colored core sands. By incorporating the kinetic theory of granular flow (KTGF, kinetic-frictional constitutive correlation and turbulence model, a two-fluid model (TFM was established to study the flow dynamics of the core shooting process. Two-fluid model (TFM simulations were then performed and a areasonable agreement was achieved between the simulation and experimental results. Based on the experimental and simulation results, the effects of turbulence, sand density, sand diameter and binder ratio were analyzed in terms of filling process, sand volume fraction (αs and sand velocity (Vs.

Submerged Pond Sand Filter—A Novel Approach to Rural Water Supply

Directory of Open Access Journals (Sweden)

Mia Øhlenschlæger

2016-06-01

Full Text Available This study describes the new design and function of a modified version of a traditional slow sand filter. The Submerged Pond Sand Filter is built inside a pond and has a vertical as well as a horizontal flow of water through a sloped filter opening. The filter provides treated drinking water to a rural Indian village. The filter has functioned with minimal maintenance for five years without being subject to the typical scraping off and changing of sand as needed in traditional slow sand filters every few months. This five-year study showed bacterial removal efficiency of 97% on average with a level of faecal coliforms of 2 ± 2 colony forming units (CFU/100 mL measured in the treated water. Turbidity was visibly removed during treatment. When water was retrieved from the filter through a manual pump for long consistent time intervals (60 min, faecal coliform counts increased from four to 10 CFU/100 mL on average compared to shorter pumping intervals (5 min. Though the treated water did not comply with the World Health Organization standards of 0 CFU/100 mL, the filter significantly improved water quality and provided one of the best sources of drinkable water in a water-depleted area, where only surface water was available. Furthermore, it is a sustainable treatment method due to low maintenance requirements.

Analysis of Physical Properties and Mineralogical of Pyrolysis Tires Rubber Ash Compared Natural Sand in Concrete material

Science.gov (United States)

Syamir Senin, Mohamad; Shahidan, Shahiron; Syazani Leman, Alif; Izzati Raihan Ramzi Hannan, Nurul

2016-11-01

Waste tires pose significant health and environmental concerns if not recycled or discarded properly. At the same time, natural sand is becoming scarcer and costlier due to its non-availability. Waste tires as fine aggregate can be an economical and sustainable alternative to the natural sand. Recent years, the interest on recycling waste tires into civil engineering applications by the researchers has increased. In this research, the chemical and physical properties of the tires rubber ash and the natural sand have been analysed. The densities of the rubber ash are lower than the natural sand. Rubber ash had finer particle size compared to the natural sand. Almost all chemical in the natural sand had in rubber ash with the additional sulphur trioxide and zinc oxide in the rubber ash, made the rubber ash better than natural sand. Rubber ash seems to be a suitable material to use in concrete as sand replacement.

Thermal Conductivity of Polymer Composite poypropilene-Sand

International Nuclear Information System (INIS)

Betha; Mashuri; Sudirman; Karo Karo, Aloma

2001-01-01

Thermal conductivity composite materials polypropylene (PP)-sand have been investigated. PP composite with sand to increase thermal conductivity from the polymer. The composite in this observation is done by mixing matrix (PP melt flow 2/10)and filler sand)by means tool labo plastomil. The result of thermal conductivity is composite of PP-sand which is obtained increase and followed by the raising of filler particle volume fraction. The analysis of thermal conductivity based on the model Cheng and Vachon, model Lewis and Nielsen where this model has the function to support experiment finding. It is proved that Lewis' and Nielsen's model almost approach experiment result. And then thermal conductivity raising will be analyzed by the model of pararel-series conductive with the two (2)phases system. It is showed that sand in PP MF 2 composite have the big role to increase the thermal conductivity than sand in PP MF 10 composition, but it is not easy to shape conductive medium

Final report on Thermally Modified Sand demonstration project

Energy Technology Data Exchange (ETDEWEB)

1994-09-23

The use of salt and salt/sand mixtures on icy roadway surfaces has dramatically increased during the past 30 years. Despite extensive documentation on salt related damage to the roadway improvements, vehicles and the environment, road maintenance departments have continued to rely on this practice. Road maintenance departments in northern climate areas have long recognized the safety benefits for public mobility on icy roadways from the use of sand. As an abrasive material, the sand improves the surface traction that results in more drivable and less hazardous road conditions during the winter months. Stockpiles of pure sand stored during the winter months oftentimes freeze into large unworkable, monolithic piles. To maintain a free-flowing condition, it has been found to be necessary to add salt to the sand. The addition of salt in amounts ranging from 5 to 10 percent to that of sand, is usually sufficient to provide relatively free-flowing abrasive material that could be stored in stockpiles and applied to icy road surfaces with conventional sand spreading trucks. Another alternative for winter storage of pure sand to maintain a free-flowing condition is in humidity-controlled, heated buildings. As would be expected, this method has high capital and operating costs. and not cost effective for general highway maintenance use. The invention demonstrated herein is a method of thermally modifying pure sand that will remain in a free-flowing state throughout the winter season without the need for the salt additive. The thermally modified sand provides an abrasive material that when applied to icy roads does not cause environmental and corrosive damage as done by the application of sand with salt. By employing a very simple process of freezing screened sand particles by forced air convection under subfreezing conditions, the invention creates a product that has significant value in terms of economic and environmental benefits.

Study on sand particles creep model and open pit mine landslide mechanism caused by sand fatigue liquefaction

Science.gov (United States)

Du, Dong-Ning; Wang, Lai-Gui; Zhang, Xiang-Dong; Zhang, Shu-Kun

2017-06-01

The sand particles in the sand - rock composite slope of the open pit mine occurs creep deformation and fatigue liquefaction under the action of vehicle load vibration and hydraulic gradient, which causes landslide geological disasters and it destroys the surface environment. To reveal the mechanism, a mechanics model based on the model considering the soil structural change with a new “plastic hinge” element is developed, to improve its constitutive and creep curve equations. Data from sand creep experiments are used to identify the parameters in the model and to validate the model. The results show that the mechanical model can describe the rotation progress between the sand particles, disclose the negative acceleration creep deformation stage during the third phase, and require fewer parameters while maintaining accuracy. It provides a new creep model considering rotation to analyze sand creep mechanism, which provides a theoretical basis for revealing the open pit mine landslide mechanism induced by creep deformation and fatigue liquefaction of sandy soil.

Effect of hardening methods of moulding sands with water glass on structure of bonding bridges

Directory of Open Access Journals (Sweden)

M. Stachowicz

2010-07-01

Full Text Available Research on influence of hardening methods on structure of bonding bridges in moulding sands with sodium water glass is presented.Moulding sands with addition of 2.5 % of binder with molar module 2.0 were hardened with CO2 and dried in traditional way or hardenedwith microwaves. It was proved that the hardening method affects structure of bonding bridges, correlating with properties of the hardened moulding sands. It was found that strength of the moulding sands hardened with microwaves for 4 min is very close to that measured after traditional drying at 110 °C for 120 min. So, application of microwave hardening ensures significant shortening of the process time to the value comparable with CO2 hardening but guaranteeing over 10-fold increase of mechanical properties. Analysis of SEM images of hardened moulding sands permitted explaining differences in quality parameters of moulding sands by connecting them with structure of the created bonding bridges.

Bacteria of Phlebotominae Sand Flies Collected in Western Iran

Directory of Open Access Journals (Sweden)

Somayeh Rafatbakhsh-Iran

2015-08-01

Full Text Available Microorganisms particularly bacteria presenting in insects such as Phlebotominae may play an important role in the epidemiology of human infectious disease. Nowadays, because of vector implications, the routine methods of controlling and spraying have no more beneficial effects on vectors and reservoirs. Little knows about the prevalence and diversity of sand fly bacteria. The main objective of this study was to determine the presence of bacteria of phlebotominae sand flies collected in Hamadan, west of Iran. This information is important in order to development of vector control strategies. The microbial flora of Phlebotomus papatasi and P. sergenti the main vector of Cutaneous Leishmaniasis in the old world, were investigated. We characterized 8 bacteria, including 5 Gram-negative bacteria: Acinetobacter lwoffii, Pseudomonas aeruginosa, Enterobacter cloacae, Edvardsiela sp. and Proteus mirabilis and Gram-positive bacteria: Bacillus subtilis, Staphylococcus saprophyticus and Micrococcus luteus. Our study provides some data on the microbiota diversity of field-collected sand flies for the first time in Hamadan. Our results indicate that there is a range of variation of aerobic bacteria inhabiting sand fly, which possibly reflect the ecological condition of the habitat where the fly breeds. Microbiota is increasingly regarded as an important factor for modulating vector competence in insect vectors. So, mirobiota can be effects on the biology of phlebotominae and their roles in the sandfly-Leishmania interaction. Further experiments are required to clearly delineate the vectorial role of sand flies. Because it is probable that in the future, factors such as environmental changes, migration and urbanization can ease the transmission of leishmaniasis in this area.

Formulating Fine to Medium Sand Erosion for Suspended Sediment Transport Models

Directory of Open Access Journals (Sweden)

François Dufois

2015-08-01

Full Text Available The capacity of an advection/diffusion model to predict sand transport under varying wave and current conditions is evaluated. The horizontal sand transport rate is computed by vertical integration of the suspended sediment flux. A correction procedure for the near-bed concentration is proposed so that model results are independent of the vertical resolution. The method can thus be implemented in regional models with operational applications. Simulating equilibrium sand transport rates, when erosion and deposition are balanced, requires a new empirical erosion law that involves the non-dimensional excess shear stress and a parameter that depends on the size of the sand grain. Comparison with several datasets and sediment transport formulae demonstrated the model’s capacity to simulate sand transport rates for a large range of current and wave conditions and sand diameters in the range 100–500 μm. Measured transport rates were predicted within a factor two in 67% of cases with current only and in 35% of cases with both waves and current. In comparison with the results obtained by Camenen and Larroudé (2003, who provided the same indicators for several practical transport rate formulations (whose means are respectively 72% and 37%, the proposed approach gives reasonable results. Before fitting a new erosion law to our model, classical erosion rate formulations were tested but led to poor comparisons with expected sediment transport rates. We suggest that classical erosion laws should be used with care in advection/diffusion models similar to ours, and that at least a full validation procedure for transport rates involving a range of sand diameters and hydrodynamic conditions should be carried out.

Sand Particles Impact on the Tribological Behavior of Sliding Contact

Directory of Open Access Journals (Sweden)

Aldajah Saud

2016-01-01

Full Text Available Lubricant contaminants cause severe problems to machines. Substantial research has been conducted to study the impact of such contaminates on the tribological performance of lubricated contacts. The primary goal of such studies is to find solutions to avoid the dirtiest cause of damaging machines’ parts and to reduce energy consumption and maintenance costs. The current study investigates the tribological behavior of contaminated lubricated contacts; the contaminants considered in this research are sand particles. The effect of the sand particles concentration levels on friction and wear of a tribological system under sliding contact was studied. Three different concentration levels were tested; 5%, 10% and 15%.The experimental program was carried out using an in-house built ball on disc machine at room temperature, constant normal load, constant speed, constant running time and constant travelling distance. Results showed that both friction coefficient and wear volume of the contacting surfaces are dependent on the concentration level of the sand particles. Both friction coefficient and wear volume increased by increasing the sand particles concentration. SEM was utilized to study the wear mechanisms of the contacting surfaces, it was found that the dominant wear mechanism in all cases was abrasive wear.

Tidal dynamics in the sand motor lagoon

NARCIS (Netherlands)

De Vries, S.; Radermacher, M.; De Schipper, M.A.; Stive, M.J.F.

2015-01-01

The Sand Motor is a mega-nourishment characterized by a very large sand volume of around 20 million m3 placed along the Dutch coast. The Sand Motor is a pilot project to evaluate the performance of an alternative nourishment strategy with respect to different functions of the coastal system. Within

Numerical simulation of flow and compression of green sand

DEFF Research Database (Denmark)

Hovad, Emil

The focus of the industrial PhD project was concentrated on the production of the sand mold (green sand) which gives the cast component its final geometrical shape. In order to ensure a high quality of the cast component, it is important to control the manufacturing process of the mold itself so...... that it is homogeneous and stable. Therefore gaining a basic understanding of how the flow and deposition of green sand should be characterized and modelled was important, so that it could be used for simulation of the manufacturing process of the sand mold. The flowability of the green sand is important when the sand...... flows down through the hopper filling the chamber with sand during the sand shot. The flowability of green sand is mostly governed by the amount of water and bentonite which both decrease it. The flowability and the internal forces thus control how well you can fill a complex mold geom-etry in which...

Analysis of the environmental control technology for tar sand development

Energy Technology Data Exchange (ETDEWEB)

de Nevers, N.; Glenne, B.; Bryner, C.

1979-06-01

The environmental technology for control of air pollution, water pollution, and for the disposal, stabilization, and vegetation of the waste tar sand were thoroughly investigated. Although some difficulties may be encountered in any of these undertakings, it seems clear that the air and water pollution problems can be solved to meet any applicable standard. Currently there are two large-scale plants producing liquid fuels from tar sands in Alberta, Canada which use similar technology involving surface mining, hot water extraction, and surface disposal of waste sand. These projects all meet the Canadian environmental control regulations in force at the time they began. The largest US deposits of tar sands are much smaller than the Canadian; 95 percent are located in the state of Utah. Their economics do not appear as attractive as the Canadian deposits. The environmental control costs are not large enough to make an otherwise economic project uneconomic. The most serious environmental conflict likely to occur over the recovery of liquid fuels from the US deposits of tar sands is that caused by the proximity of the deposits to national parks, national monuments, and a national recreation area in Utah. These areas have very stringent air pollution requirements; and even if the air pollution control requirements can be met, there may still be adequate opposition to large-scale mining ventures in these areas to prevent their commercial exploitation. Another environmental constraint may be water rights availability.Essentially all of the water running in the Colorado river basin is now legally allocated. Barring new interpretations of the legality of water rights purchase, Utah tar sands developments should be able to obtain water by purchasing existing irrigation water rights.

Sand wave fields beneath the Loop Current, Gulf of Mexico: Reworking of fan sands

Science.gov (United States)

Kenyon, Neil H.; Akhmetzhanov, A.M.; Twichell, D.C.

2002-01-01

Extensive fields of large barchan-like sand waves and longitudinal sand ribbons have been mapped by deep-towed SeaMARC IA sidescan sonar on part of the middle and lower Mississippi Fan that lies in about 3200 m of water. The area is beneath the strongly flowing Loop Current. The bedforms have not been adequately sampled but probably consist of winnowed siliciclastic-foraminiferal sands. The size (about 200 m from wingtip to wingtip) and shape of the large barchans is consistent with a previously observed peak current speed of 30 cm/s, measured 25 m above the seabed. The types of small-scale bedforms and the scoured surfaces of chemical crusts, seen on nearby bottom photographs, indicate that near-bed currents in excess of 30 cm/s may sometimes occur. At the time of the survey the sand transport direction was to the northwest, in the opposite direction to the Loop Current but consistent with there being a deep boundary current along the foot of the Florida Escarpment. Some reworking of the underlying sandy turbidites and debris flow deposits is apparent on the sidescan sonar records. Reworking by deep-sea currents, resulting in erosion and in deposits characterised by coarsening upwards structures and cross-bedding, is a process that has been proposed for sand found in cores in shallower parts of the Gulf of Mexico. This process is more widespread than hitherto supposed. 

Oil sands and the environment

Energy Technology Data Exchange (ETDEWEB)

Seeley, R. [Shell Canada Ltd., Calgary, AB (Canada). Calgary Research Centre

2004-07-01

Oil sands are a significant resource for Alberta and Canada with continuing growth opportunity. There is a need to ensure sustainable development of the oil sands resources from a social, economic and environmental perspective. The industry has succeeded in terms of proven reserves, technology advancements, reduced operating costs, reliability and market accessibility. Some of the major challenges facing the industry include high capital cost, infrastructure, social services and keeping pace with growth. This presentation outlined the proactive measures that the oil sands industry has taken to manage environmental issues such as sulphur dioxide and nitrogen oxide emissions, greenhouse gases, water management and land reclamation. tabs., figs.

Alberta oil sands royalty regime

International Nuclear Information System (INIS)

Asgarpour, S.

2004-01-01

The long term objective of the Oil Sands Business Unit of Alberta Energy is to pave the way for Alberta's bitumen production to reach 3 million barrels per day by 2020. This presentation described the national government's role in resource development. It was emphasized that since the Crown is the owner of the oil sands resource, it would benefit by providing strategic leadership and by generating a larger royalty base. The oil sands fiscal regime was described with reference to generic royalty, risk sharing, investment, and project economics. Business rule principles were also outlined along with criteria for project expansions. Both upstream and downstream challenges and opportunities were listed. 4 figs

Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

Science.gov (United States)

Nirmala, D. B.; Raviraj, S.

2016-06-01

This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC) containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37) Orthogonal Arrays (OA) with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering "Nominal the better" situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

Ethoxyresorufin-O-deethylase (EROD) induction in rainbow trout exposed to diluted oil sand wastewater

International Nuclear Information System (INIS)

Verbeek, A.; Mackay, W.; Birkholz, D.

1995-01-01

Toxic industrial wastewaters, such as those from oil sands extraction, must be assessed for their potential sublethal effects before they can be safely disposed in the environment. The induction of ethoxyresorufin-O-deethylase activity was assessed as a potential bioindicator of sublethal stress in rainbow trout exposed to sublethal concentrations of oil sands tailings water. The mixed-function oxygenase system in rainbow trout responded rapidly following a definable concentration-response relationship; however, it proved to be a relatively insensitive indicator of sublethal exposure to oil sands tailings water. Increased activity and maximal induction, as a result of exposure to 0.3 and 0.6 times the LC 50 (Toxic Units), occurred rapidly within 24 hours of exposure. The linearity of the relationship between the concentration of oil sands tailings pond water and ethoxyresorufin-O-deethylase activity, expressed by the following regression equation, In EROD = 3.68 (conc.) + 3.20, had an r 2 value of 0.593. Maximal induction required 0.4--0.8 Toxic Units. The absolute level of maximal induction was only one-fifth to one-sixth of the potential induction as found in response to the positive control, 0.5 mg/kg β-naphthoflavone (i.p.). The authors also present data that suggests that the different levels of induction observed in trout exposed to tailings pond water vs those injected with 0.5 mg/kg β-naphthoflavone (i.p.) may be indicative of two different P450 isoforms, the CYP4Al isoform responding to the organic acidic surfactants in oil sands tailings pond water and the CYP1A1 isoform, the isoform generally associated with most xenobiotic transformation in fish, responding to β-naphthoflavone

Dynamic response of sand particles impacted by a rigid spherical object

Directory of Open Access Journals (Sweden)

P. Youplao

2018-06-01

Full Text Available A method for measuring the dynamic impact responses that acting on a spherical object while dropping and colliding with dried sand, such as the velocity, displacement, acceleration, and resultant force, is presented and discussed. In the experiment, a Michelson-type laser interferometer is employed to obtain the velocity of the spherical stainless steel object. Then the obtained time velocity profile is used to calculate the acceleration, the displacement, and the inertial force acting on the observed sand particles. Furthermore, a high-speed camera is employed to observe the behavior of the sand during the collision. From the experimental results with the sampling interval for frequencies calculation of 1 ms, the combined standard uncertainty in the instantaneous value of the impact force acts on the observed object is obtained and approximated to 0.49 N, which is related to a corresponding 4.07% of the maximum value at 12.05 N of the impact force. Keywords: Sand particle, Collision response, Dynamic force, Inertial mass, Optical interferometer

Observations during static and cyclic undrained loading of dense Aalborg University sand no. 1

DEFF Research Database (Denmark)

Sabaliauskas, Tomas; Diaz, Alberto Troya; Ibsen, Lars Bo

. Soil strength and stiffness are found to change depending on the type of loading applied. Effective friction angle is found to be changing during various phases of loading. Linear Mohr Coulomb model could potentially be sufficient for modeling the full spectrum of dense sand behavior if extended...... with a changing friction angle following the examined patterns of response. A total stress path based material model is presented in this paper....

Evolution of the gas atmosphere during filing the sand moulds with iron alloys

Directory of Open Access Journals (Sweden)

J. Mocek

2009-10-01

Full Text Available Evolution of atmosphere of the mould cavity when pouring the cast iron has been analyzed. It was find that in dry sand mold the cavity is filled by air throughout the casting time. In green sand the air is removed by the water vapor the hydrogen or carbon oxides formed in contact with the liquid metal. The theoretical results have been confirmed experimentally.

Checklist of American sand flies (Diptera, Psychodidae, Phlebotominae: genera, species, and their distribution

Directory of Open Access Journals (Sweden)

Paloma Helena Fernandes Shimabukuro

2017-03-01

Full Text Available Phlebotomine sand flies are dipteran insects of medical importance because many species are involved in the transmission of pathogens between human and non-human animals. A total of 530 American species of sand flies is presented in an updated checklist, along with their author(s and year of publication using the classification by Galati (1995, 2003. Distribution by country is also provided.

BENTONITE-QUARTZ SAND AS THE BACKFILL MATERIALS ON THE RADIOACTIVE WASTE REPOSITORY

Directory of Open Access Journals (Sweden)

Raharjo Raharjo

2010-06-01

Full Text Available An investigation of the contribution of quartz sand in the bentonite mixture as the backfill materials on the shallow land burial of radioactive waste has been done. The experiment objective is to determine the effect of quartz sand in a bentonite mixture with bentonite particle sizes of -20+40, -40+60, and -60+80 mesh on the retardation factor and the uranium dispersion in the simulation of uranium migration in the backfill materials. The experiment was carried out by the fixed bed method in the column filled by the bentonite mixture with a bentonite-to-quartz sand weight percent ratio of 0/100, 25/75, 50/50, 75/25, and 100/0 on the water saturated condition flown by uranyl nitrate solution at concentration (Co of 500 ppm. The concentration of uranium in the effluents in interval 15 minutes represented as Ct was analyzed by spectrophotometer, then using Co and Ct, retardation factor (R and dispersivity ( were determined. The experiment data showed that the bentonite of -60+80 mesh and the quartz sand of -20+40 mesh on bentonite-to-quartz sand with weight percent ratio of 50/50 gave the highest retardation factor and dispersivity of 18.37 and 0.0363 cm, respectively.   Keywords: bentonite, quartz sand, backfill materials, radioactive waste

Oil sands tailings management project

Energy Technology Data Exchange (ETDEWEB)

Godwalt, C. [Alberta WaterSMART, Calgary, AB (Canada); Kotecha, P. [Suncor Energy Inc, Calgary, AB (Canada); Aumann, C. [Alberta Innovates - Technology Futures, Alberta Governement, AB (Canada)

2010-11-15

The Oil sands leadership initiative (OSLI) works with the Government of Alberta on the development of the oil sands industry, considering environmental, economical and social aspects. Water management was identified as one of most important areas to focus on. Alberta WaterSMART was requested to support the development and the management of projects resulting from the work done or underway in this field. The development of a regional water management solution stood out as the most interesting solution to obtain significant results. In the Athabasca Region, oil sands producers work independently on their water sourcing and disposal with particular attention to fresh water conservation and economics. The Athabasca River represents a source for mines and distant saline aquifers are the target of steam assisted gravity drainage (SAGD) operators. As part of a four-phase project aiming to study the environmental and economic footprint (EEF) benefit of alternatives for Athabasca oil sands production water supply and disposal, the purpose of the tailings water management project was to identify tailings treatment technologies that are ready to be implemented, and to design and evaluate solutions in order to improve regional oil sands production water sourcing and disposal. Alternatives were evaluated based on their total EEF, applying a lifecycle assessment methodology with a particular attention on the quantification of important performance indicators. 25 refs., 8 tabs., 40 figs.

Oil sands tailings management project

International Nuclear Information System (INIS)

Godwalt, C.; Kotecha, P.; Aumann, C.

2010-11-01

The Oil sands leadership initiative (OSLI) works with the Government of Alberta on the development of the oil sands industry, considering environmental, economical and social aspects. Water management was identified as one of most important areas to focus on. Alberta WaterSMART was requested to support the development and the management of projects resulting from the work done or underway in this field. The development of a regional water management solution stood out as the most interesting solution to obtain significant results. In the Athabasca Region, oil sands producers work independently on their water sourcing and disposal with particular attention to fresh water conservation and economics. The Athabasca River represents a source for mines and distant saline aquifers are the target of steam assisted gravity drainage (SAGD) operators. As part of a four-phase project aiming to study the environmental and economic footprint (EEF) benefit of alternatives for Athabasca oil sands production water supply and disposal, the purpose of the tailings water management project was to identify tailings treatment technologies that are ready to be implemented, and to design and evaluate solutions in order to improve regional oil sands production water sourcing and disposal. Alternatives were evaluated based on their total EEF, applying a lifecycle assessment methodology with a particular attention on the quantification of important performance indicators. 25 refs., 8 tabs., 40 figs.

Delineating chalk sand distribution of Ekofisk formation using probabilistic neural network (PNN) and stepwise regression (SWR): Case study Danish North Sea field

Science.gov (United States)

Haris, A.; Nafian, M.; Riyanto, A.

2017-07-01

Danish North Sea Fields consist of several formations (Ekofisk, Tor, and Cromer Knoll) that was started from the age of Paleocene to Miocene. In this study, the integration of seismic and well log data set is carried out to determine the chalk sand distribution in the Danish North Sea field. The integration of seismic and well log data set is performed by using the seismic inversion analysis and seismic multi-attribute. The seismic inversion algorithm, which is used to derive acoustic impedance (AI), is model-based technique. The derived AI is then used as external attributes for the input of multi-attribute analysis. Moreover, the multi-attribute analysis is used to generate the linear and non-linear transformation of among well log properties. In the case of the linear model, selected transformation is conducted by weighting step-wise linear regression (SWR), while for the non-linear model is performed by using probabilistic neural networks (PNN). The estimated porosity, which is resulted by PNN shows better suited to the well log data compared with the results of SWR. This result can be understood since PNN perform non-linear regression so that the relationship between the attribute data and predicted log data can be optimized. The distribution of chalk sand has been successfully identified and characterized by porosity value ranging from 23% up to 30%.

Invasive plants on disturbed Korean sand dunes

Science.gov (United States)

Kim, Kee Dae

2005-01-01

The sand dunes in coastal regions of South Korea are important ecosystems because of their small size, the rare species found in this habitat, and the beautiful landscapes they create. This study investigated the current vegetative status of sand dunes on three representative coasts of the Korean peninsula, and on the coasts of Cheju Island, and assessed the conditions caused by invasive plants. The relationships between the degree of invasion and 14 environmental variables were studied. Plots of sand dunes along line transects perpendicular to the coastal lines were established to estimate vegetative species coverage. TWINSPAN (Two-Way Indicator Species Analysis), CCA (Canonical Correspondence Analysis), and DCCA (Detrended Canonical Correspondence Analysis) were performed to classify communities on sand dunes and assess species composition variation. Carex kobomugi, Elymus mollis, and Vitex rotundifolia were found to be the dominant species plotted on the east, the west, and the peripheral coasts of Cheju Island, respectively. Vegetation on the south coast was totally extinct. The 19 communities, including representative C. kobomugi, C. kobomugi- Ixeris repens, C. kobomugi- Oenothera biennis, E. mollis, Lolium multiflorum- Calystegia soldanella, and V. rotundifolia- C. kobomugi, were all classified according to TWINSPAN. Oenothera biennis and L. multiflorum were exotics observed within these native communities. CCA showed that invasive native and exotic species distribution was segregated significantly, according to disturbance level, exotic species number, gravel, sand and silt contents, as well as vegetation size. It further revealed that human disturbance can strongly favor the settlement of invasive and exotic species. Restoration options to reduce exotic plants in the South Korean sand dune areas were found to be the introduction of native plant species from one sand dune into other sand dune areas, prohibition of building and the introduction of exotic

The immune response to sand fly salivary proteins and its influence on Leishmania immunity

Directory of Open Access Journals (Sweden)

Regis eGomes

2012-05-01

Full Text Available Leishmaniasis is a vector-borne disease transmitted by bites of phlebotomine sand flies. During Leishmania transmission, sand fly saliva is co-inoculated with parasites into the skin of the mammalian host. Sand fly saliva consists of roughly thirty different salivary proteins, many with known roles linked to blood feeding facilitation. Apart from the anti-hemostatic capacity of saliva, several sand fly salivary proteins have been shown to be immunogenic upon multiple contacts with a mammalian host. Immunization with single immunogenic salivary proteins or exposure to uninfected bites can produce protective immune responses against leishmaniasis. These sand fly salivary proteins induce cellular immune responses and/or antibodies. Antibodies to saliva are not required for protection in a mouse model against leishmaniasis. A strong body of evidence points to the role for saliva-specific T cells producing IFN-γ in the form of a delayed-type hypersensitivity reaction at the bite site as the main protective response. Herein, we review immunity to sand fly salivary proteins in the context of its vector-parasite-host combinations and vaccine potential, as well as some recent advances to shed light on the mechanism of how an immune response to sand fly saliva protects against leishmaniasis.

Characteristics of SCC with Fly Ash and Manufactured Sand

Science.gov (United States)

Praveen Kumar, K.; Radhakrishna

2016-09-01

Self compacting concrete (SCC) of M40 grade was designed. The binder in SCC consists of OPC and fly ash in the ratio of 65:35. River sand was replaced by manufactured sand (M-sand) at replacement levels of 20,40,60,80 and 100%. An attempt was made to evaluate the workability and strength characteristics of self compacting concrete with river sand and manufactured sand as fine aggregates. For each replacement level, constant workability was maintained by varying the dosage of superplasticizer. T50 flow time, V Funnel time, V-funnel T5 time as well as compressive, split tensile and flexural strength of SCC were found at each replacement level of M-sand. They were compared to SCC with river sand. Results indicate favourable use of M-sand in preparation of Self Compacting Concrete.

Moulding Sands with New InorganicBinders - Ecology Assessment in the Aspect of Work Environment

Directory of Open Access Journals (Sweden)

I. Szanda

2012-09-01

Full Text Available The development of economy and industry introducing new technologies and materials often means the increased threat of occurrenceof factors harmful to humans and environment. Workers employed in foundries as mould pourers are the group of high professional risk.Foundry moulding sands when poured with liquid metal are a source of the emission of harmful, toxic and carcinogenic (benzene,PAHs compounds.The paper presents the results of studies on the concentration of chemical compounds emitted in the process of casting aluminiumalloy and brass using moulding sands with the new inorganic binders. The specific values of the exposure indices were compared with thelimit values. This enabled an assessment of the impact of moulding sands on work environment. The obtained results were compared withthe values of contaminants emitted when pouring foundry moulds made from furan sands and bentonite sands with an addition of coaldust.Studies were carried out under the project POIG.01.01.02-00-015/09 "Advanced materials and technologies."

Documenting the global impacts of beach sand mining

Science.gov (United States)

Young, R.; Griffith, A.

2009-04-01

For centuries, beach sand has been mined for use as aggregate in concrete, for heavy minerals, and for construction fill. The global extent and impact of this phenomenon has gone relatively unnoticed by academics, NGOs, and major news sources. Most reports of sand mining activities are found at the very local scale (if the mining is ever documented at all). Yet, sand mining in many localities has resulted in the complete destruction of beach (and related) ecosystems along with severe impacts to coastal protection and tourism. The Program for the Study of Developed Shorelines at Western Carolina University and Beachcare.org have initiated the construction of a global database of beach sand mining activities. The database is being built through a combination of site visits and through the data mining of media resources, peer reviewed papers, and reports from private and governmental entities. Currently, we have documented sand mining in 35 countries on 6 continents representing the removal of millions of cubic meters of sand. Problems extend from Asia where critical infrastructure has been disrupted by sand mining to the Caribbean where policy reform has swiftly followed a highly publicized theft of sand. The Program for the Study of Developed Shorelines recently observed extensive sand mining in Morocco at the regional scale. Tens of kilometers of beach have been stripped of sand and the mining continues southward reducing hope of a thriving tourism-based economy. Problems caused by beach sand mining include: destruction of natural beaches and the ecosystems they protect (e.g. dunes, wetlands), habitat loss for globally important species (e.g. turtles, shorebirds), destruction of nearshore marine ecosystems, increased shoreline erosion rates, reduced protection from storms, tsunamis, and wave events, and economic losses through tourist abandonment and loss of coastal aesthetics. The threats posed by sand mining are made even more critical given the prospect of a

Studies on various characteristics of concrete structures using crushed sand

International Nuclear Information System (INIS)

Mimatsu, Makoto; Sugita, Hideaki; Yonemura, Masataka.

1985-01-01

With the recent advances of construction industry, the demands for concrete, hence for aggregate, are rising. The sand as such is in extreme shortage due to the exhaustion of river sand. Under the situation, the recent trends are for the use of crushed sand, i.e. the artificial sand obtained by crushing rocks, which have advantages of stabilized quality and adequate supplies. In building of nuclear power plants requiring large amounts of concrete, the usage of crushed sand is now unavoidable. The following are described : the situation of aggregate in Kyushu. production method of crushed sand and the quality standards, rocks used for crushed stone and sand and the properties, quality survey on crushed sand and the basic tests, characteristic tests of crushed-stone and -sand mixed concrete, the application of crushed sand in structures of the Sendai Nuclear Power Station. (Mori, K.)

Early Cretaceous trypanosomatids associated with fossil sand fly larvae in Burmese amber

Directory of Open Access Journals (Sweden)

George Poinar Jr

2007-08-01

Full Text Available Early Cretaceous flagellates with characters typical of trypanosomatids were found in the gut of sand fly larvae, as well as in surrounding debris, in Burmese amber. This discovery supports a hypothesis in which free-living trypanosomatids could have been acquired by sand fly larvae in their feeding environment and then carried transtadially into the adult stage. At some point in time, specific genera were introduced into vertebrates, thus establishing a dixenous life cycle.

Experimental perforation of tubing with a hydraulic sand jet

Energy Technology Data Exchange (ETDEWEB)

Semenov, Yu V

1970-01-01

A series of field tests has shown that perforation with a hydraulic sand jet improves the quality of well completion. The sand jet does not crack the cement sheath or the casing, and the perforations are larger and deeper than perforations formed by explosive charges. Fluid circulation during sand jet perforation can safely be stopped for at least 10 min. Water containing a surfactant can be used as a sand carrier. Sand jet perforation allows successful completion of wells cased by 2 tubing strings. Sand jet perforation can be used to clean the borehole well and to remove foreign objects from the well.

Experimental Study on Superfine Sand Concrete Mixed by Double Mixing Technology

OpenAIRE

yuqing zhao

2013-01-01

Traditional concept thought that medium sand and fine sand can be used to mix concrete, superfine sand can not used to mix concrete. This makes the source of superfine sand limited. With the shortage of medium sand and fine sand, it is imperative to exploit the resource of superfine sand. Superfine sand concrete is mixed by means of Double-doped Technology-ultra-fine fly ash and super plasticizer. Primary factor influencing superfine sand concrete strength is studied by orthogonal test, the o...

Aeolian sands as material to construct low-volume roads

CSIR Research Space (South Africa)

Paige-Green, P

2011-07-01

Full Text Available Aeolian sands are widespread in many semi-arid to arid areas of the world and often provide the only economic source of construction materials for low volume roads. Experience in southern Africa over a number of decades has shown that provided...

The physics of wind-blown sand and dust.

Science.gov (United States)

Kok, Jasper F; Parteli, Eric J R; Michaels, Timothy I; Karam, Diana Bou

2012-10-01

The transport of sand and dust by wind is a potent erosional force, creates sand dunes and ripples, and loads the atmosphere with suspended dust aerosols. This paper presents an extensive review of the physics of wind-blown sand and dust on Earth and Mars. Specifically, we review the physics of aeolian saltation, the formation and development of sand dunes and ripples, the physics of dust aerosol emission, the weather phenomena that trigger dust storms, and the lifting of dust by dust devils and other small-scale vortices. We also discuss the physics of wind-blown sand and dune formation on Venus and Titan.

Characterizing volumetric deformation behavior of naturally occuring bituminous sand materials

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2009-05-01

Full Text Available newly proposed hydrostatic compression test procedure. The test procedure applies field loading conditions of off-road construction and mining equipment to closely simulate the volumetric deformation and stiffness behaviour of oil sand materials. Based...

Sand Dunes with Frost

Science.gov (United States)

2004-01-01

9 May 2004 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows a suite of frost-covered sand dunes in the north polar region of Mars in early spring, 2004. The dunes indicate wind transport of sand from left to right (west to east). These landforms are located near 78.1oN, 220.8oW. This picture is illuminated by sunlight from the lower left and covers an area about 3 km (1.9 mi) across.

Relationships between sand and water quality at recreational beaches.

Science.gov (United States)

Phillips, Matthew C; Solo-Gabriele, Helena M; Piggot, Alan M; Klaus, James S; Zhang, Yifan

2011-12-15

Enterococci are used to assess the risk of negative human health impacts from recreational waters. Studies have shown sustained populations of enterococci within sediments of beaches but comprehensive surveys of multiple tidal zones on beaches in a regional area and their relationship to beach management decisions are limited. We sampled three tidal zones on eight South Florida beaches in Miami-Dade and Broward counties and found that enterococci were ubiquitous within South Florida beach sands although their levels varied greatly both among the beaches and between the supratidal, intertidal and subtidal zones. The supratidal sands consistently had significantly higher (p sand) than the other two zones. Levels of enterococci within the subtidal sand correlated with the average level of enterococci in the water (CFU/100mL) for the season during which samples were collected (r(s) = 0.73). The average sand enterococci content over all the zones on each beach correlated with the average water enterococci levels of the year prior to sand samplings (r(s) = 0.64) as well as the average water enterococci levels for the month after sand samplings (r(s) = 0.54). Results indicate a connection between levels of enterococci in beach water and sands throughout South Florida's beaches and suggest that the sands are one of the predominant reservoirs of enterococci impacting beach water quality. As a result, beaches with lower levels of enterococci in the sand had fewer exceedences relative to beaches with higher levels of sand enterococci. More research should focus on evaluating beach sand quality as a means to predict and regulate marine recreational water quality. Copyright © 2011 Elsevier Ltd. All rights reserved.

Prolífica George Sand

Directory of Open Access Journals (Sweden)

Àngels Santa

2014-04-01

Full Text Available A propósito de las obras de George Sand, Œuvres complètes. Sous la direction de Béatrice Didier. 1841-1842.Un hiver à Majorque. Édition critique par Angela Ryan. Horace.Édition critique par Jeanne Brunereau (París, Honoré Champion, 2013, 748 p. ISBN : 9782745319265 y Œuvres complètes. ́Sous la direction de Béatrice Didier. 1849.La petite Fadette. Édition critique par Andrée Mansau (París, Honoré Champion, 2013, 345p. ISBN : 9782745319203

Controls on the abruptness of gravel-sand transitions

Science.gov (United States)

Venditti, J. G.; Church, M. A.; Lamb, M. P.; Domarad, N.; Rennie, C. D.

2014-12-01

As gravel-bedded rivers fine downstream, they characteristically exhibit an abrupt transition from gravel- to sand-bed. This is the only abrupt transition in grain-size that occurs in the fluvial system and has attracted considerable attention. A number of competing theories have been proposed to account for the abruptness of the transition, including base-level control, attrition of ~10mm gravel to produce sand, and sediment sorting processes. The prevailing theory for the emergence of abrupt transitions is size selective sorting of bimodal sediment wherein gravel deposits due to downstream declining shear stress, fining the bedload until a sand-bed emerges. We explored this hypothesis by examining grain-size, shear stress, gravel mobility and sand suspension thresholds through the gravel-sand transition (GST) of the Fraser River, British Columbia. The Fraser GST is an arrested gravel wedge with patches of gravel downstream of the wedge forming a diffuse extension. There is an abrupt change in bed slope through the transition that leads to an abrupt change in shear stress. The GST, bed-slope change and backwater caused by the ocean are all coincident spatially, which enhances the sharpness of the GST. Interestingly, the bimodal reach of the river occurs downstream of the GST and exhibits no downstream gradients in shear stress, suspended sediment flux, gravel mobility or sand suspension thresholds. This calls into question the prevailing theory for the emergence of an abrupt GST by size selective sorting. We provide evidence, both empirical and theoretical, that suggests the emergence of an abrupt GST is caused by rapid deposition of sand when fine gravel deposits. We argue that the emergence of gravel-sand transitions is a consequence of gravel-bedded rivers adopting a steeper slope than sand-bedded rivers. The abruptness arises because the bed slope required to convey the gravel load fixes the distal location of a terminal gravel wedge, and once the river has

The Compressibility and Swell of Mixtures for Sand-Clay Liners

Directory of Open Access Journals (Sweden)

Muawia A. Dafalla

2017-01-01

Full Text Available Sand-clay liners utilize expansive clay to act as a filler to occupy the voids in the sand and thus reduce the hydraulic conductivity of the mixture. The hydraulic conductivity and transfer of water and other substances through sand-clay mixtures are of prime concern in the design of liners and hydraulic barriers. Many successful research studies have been undertaken to achieve appropriate mixtures that satisfy hydraulic conductivity requirements. This study investigates compressibility and swelling properties of mixtures to ensure that they were acceptable for light structures, roads, and slabs on grade. A range of sand-expansive clay mixtures were investigated for swell and compression properties. The swelling and compressibility indices were found to increase with increasing clay content. The use of highly expansive material can result in large volume changes due to swell and shrinkage. The inclusion of less expansive soil material as partial replacement of bentonite by one-third to two-thirds is found to reduce the compressibility by 60% to 70% for 10% and 15% clay content, respectively. The swelling pressure and swell percent were also found significantly reduced. Adding less expansive natural clay to bentonite can produce liners that are still sufficiently impervious and at the same time less problematic.

Oil sands to the rescue: oil sand microbial communities can degrade recalcitrant alkyl phenyl alkanoic acids

Energy Technology Data Exchange (ETDEWEB)

Whitby, Corinne [University of Essex (Canada)], email: cwhitby@essex.ac.uk

2011-07-01

Almost half of all global oil reserves are found as biodegraded heavy oils found in vast tar sand deposits located in North and South America and these account for 47% of Canadian oil production. Oil sand extraction generates large amounts of toxic waste water, known as oil sand process waters (OSPW), that are stored in large tailing ponds that contain toxic compounds like naphthenic acids (NAs). The presence of NAs creates problems like toxicity, corrosion, and the formation of calcium napthenate deposits which block pipelines and other infrastructure and need to be removed. This paper presents oil sand microbial communities that can degrade these NAs. The approach is to apply new aliphatic and aromatic NAs as substrates to supplement and identify NA degrading microbes and also to identify the metabolites produced and explain NA degradation pathways and the functional genes involved. The chemistry and the processes involved are explained. From the results, it is suggested that pure cultures of P. putida KT2440 be used against NAs.

EFFECTIVENESS OF THE SANDPITS SECURITY SYSTEM AGAINST MICROORGANISMS AND INTESTINAL PARASITES SAND CONTAMINATION

Directory of Open Access Journals (Sweden)

Magdalena Błaszak

2015-09-01

Full Text Available Playgrounds and sandpits (small architecture objects according to the Construction Law are subject to meticulous supervision, both at the design stage and subsequent status checks of the objects. One of the requirements arising from the need to protect playgrounds from animals is the necessity for fencing the object (Regulation of 31 December 2002 On Safety and Hygiene in Public and Private Schools and Institutions; Polish Standard PN-EN 1176 Playground equipment and surfacing. Does fencing playgrounds really reduce contamination of sand? To verify this hypothesis, the studies have been conducted on the residential areas’ sandpits, both fence secured and unsecured, located in close proximity to one another. The aim of the study was to evaluate the effectiveness of fences and nets as protection from microbial and parasite contamination of sandpits, mainly due to the access of animals to them. For several seasons of spring and summer the sand was examined in terms of the total number of heterotrophic bacteria and fungi (organic matter contamination of sand indicators and for the presence of coliform bacteria (including Escherichia coli, bacteria of the Salmonella genus and the eggs of intestinal parasites. It can be concluded that fencing playgrounds affects sand pollution less with waste and plant material (as a consequence, it has been reported statistically significantly less heterotrophic bacteria and fungi in the fenced sandpits’ sand. Unfortunately, the fence does not eliminate the risks associated with sand pollution of coliform bacteria. Cats and birds, but also dogs, still have a continuous access to sand. Due to the repeatedly stated carelessness of children and their caregivers, gates left open to the playground do not constitute an obstacle for domestic and stray animals. Another source of sand pollution with intestinal pathogens can be a manner of carriage of new sand, as there is no legislation governing the issue of transport

Evaluating the oil sands reclamation process: Assessing policy capacity and stakeholder access for government and non-governmental organizations operating in Alberta's oil sands

Science.gov (United States)

Patterson, Tyler

By employing interpretive policy analysis this thesis aims to assess, measure, and explain policy capacity for government and non-government organizations involved in reclaiming Alberta's oil sands. Using this type of analysis to assess policy capacity is a novel approach for understanding reclamation policy; and therefore, this research will provide a unique contribution to the literature surrounding reclamation policy. The oil sands region in northeast Alberta, Canada is an area of interest for a few reasons; primarily because of the vast reserves of bitumen and the environmental cost associated with developing this resource. An increase in global oil demand has established incentive for industry to seek out and develop new reserves. Alberta's oil sands are one of the largest remaining reserves in the world, and there is significant interest in increasing production in this region. Furthermore, tensions in several oil exporting nations in the Middle East remain unresolved, and this has garnered additional support for a supply side solution to North American oil demands. This solution relies upon the development of reserves in both the United States and Canada. These compounding factors have contributed to the increased development in the oil sands of northeastern Alberta. Essentially, a rapid expansion of oil sands operations is ongoing, and is the source of significant disturbance across the region. This disturbance, and the promises of reclamation, is a source of contentious debates amongst stakeholders and continues to be highly visible in the media. If oil sands operations are to retain their social license to operate, it is critical that reclamation efforts be effective. One concern non-governmental organizations (NGOs) expressed criticizes the current monitoring and enforcement of regulatory programs in the oil sands. Alberta's NGOs have suggested the data made available to them originates from industrial sources, and is generally unchecked by government

Pullout capacity of batter pile in sand.

Science.gov (United States)

Nazir, Ashraf; Nasr, Ahmed

2013-03-01

Many offshore structures are subjected to overturning moments due to wind load, wave pressure, and ship impacts. Also most of retaining walls are subjected to horizontal forces and bending moments, these forces are due to earth pressure. For foundations in such structures, usually a combination of vertical and batter piles is used. Little information is available in the literature about estimating the capacity of piles under uplift. In cases where these supporting piles are not vertical, the behavior under axial pullout is not well established. In order to delineate the significant variables affecting the ultimate uplift shaft resistance of batter pile in dry sand, a testing program comprising 62 pullout tests was conducted. The tests are conducted on model steel pile installed in loose, medium, and dense sand to an embedded depth ratio, L/d, vary from 7.5 to 30 and with various batter angles of 0°, 10°, 20°, and 30°. Results indicate that the pullout capacity of a batter pile constructed in dense and/or medium density sand increases with the increase of batter angle attains maximum value and then decreases, the maximum value of Pα occurs at batter angle approximately equal to 20°, and it is about 21-31% more than the vertical pile capacity, while the pullout capacity for batter pile that constructed in loose sand decreases with the increase of pile inclination. The results also indicated that the circular pile is more resistant to pullout forces than the square and rectangular pile shape. The rough model piles tested is experienced 18-75% increase in capacity compared with the smooth model piles. The suggested relations for the pullout capacity of batter pile regarding the vertical pile capacity are well predicted.

Stakeholder relations in the oil sands : managing uncertainty

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-05-15

Alberta's oil sands are now at the crossroads of a series of significant and complex global issues that will require careful negotiation by all stakeholders involved in the oil sands industry. This paper discussed methods of managing uncertainty and risk related to the oil sands industry's agenda for the future. Oil sands developers must continue to secure permission from communities and other key stakeholders in order to develop oil sand projects. Stakeholder relations between oil sands operators, First Nations, and Metis Nation communities must ensure that respect is maintained while environmental impacts are minimized and long-term economic benefits are secured for all parties. Environmental non-governmental organizations (ENGOs) must ensure that oil sands resources are developed responsibly, and that environmental standards are maintained. Seven key shifts in stakeholder relations resulting from the recent economic crisis were identified. These included (1) withdrawal from the multi-stakeholder process, (2) increased focus on government to demonstrate policy leadership, (3) a stronger push from ENGOs to express environmental concerns, (4) global lobby and public relations efforts from ENGOs, (5) companies retreating to local community stakeholders, (6) more active demands from First Nations and Metis Nations groups, and (7) companies challenging ENGO campaigns. The study concluded by suggesting that government leadership is needed to clear policy and regulatory frameworks for Canada's oil sands.

Providing floating capabilities in latest-generation sand screens

Energy Technology Data Exchange (ETDEWEB)

Bowen, E.G.; Coronado, M.P. [Society of Petroleum Engineers, Richardson, TX (United States)]|[Baker Hughes, Houston, TX (United States)

2008-10-15

Alternative production methods are needed for the massive reserves located in the bitumen region of Canada's tar sands. The area has over 100 installations of sand screens/slotted liners in both injection and production legs using steam-assisted gravity drainage (SAGD) technology. Multiple wells must be drilled from a single pad because of the sensitive nature of the environment. With significant depths of these wells, a floating sand screen provides assurance that the sand screen will reach the desired depth. Paraffin is generally used to plug the flow access of the screen during installation. This paper discussed a new technology that has been developed to allow for sand screen installations without relying on paraffin wax to withstand differential pressure. The new technology uses a hydro-mechanical valving system incorporated into the screen design to temporarily close off the screen while being run in the hole. The paper described how the technology could provide a reliable, time-saving solution for SAGD installations when floating sand control screens are needed. The paper discussed current technology and its limitations, sand screen installation, screen design for floating applications, and additional applications. It was concluded that this technology solution provides a unique alternative to the methods currently used to install sand screens with SAGD technology in the fast growing Canadian market for bitumen recovery. 2 refs., 5 figs.

Available pressure amplitude of linear compressor based on phasor triangle model

Science.gov (United States)

Duan, C. X.; Jiang, X.; Zhi, X. Q.; You, X. K.; Qiu, L. M.

2017-12-01

The linear compressor for cryocoolers possess the advantages of long-life operation, high efficiency, low vibration and compact structure. It is significant to study the match mechanisms between the compressor and the cold finger, which determines the working efficiency of the cryocooler. However, the output characteristics of linear compressor are complicated since it is affected by many interacting parameters. The existing matching methods are simplified and mainly focus on the compressor efficiency and output acoustic power, while neglecting the important output parameter of pressure amplitude. In this study, a phasor triangle model basing on analyzing the forces of the piston is proposed. It can be used to predict not only the output acoustic power, the efficiency, but also the pressure amplitude of the linear compressor. Calculated results agree well with the measurement results of the experiment. By this phasor triangle model, the theoretical maximum output pressure amplitude of the linear compressor can be calculated simply based on a known charging pressure and operating frequency. Compared with the mechanical and electrical model of the linear compressor, the new model can provide an intuitionistic understanding on the match mechanism with faster computational process. The model can also explain the experimental phenomenon of the proportional relationship between the output pressure amplitude and the piston displacement in experiments. By further model analysis, such phenomenon is confirmed as an expression of the unmatched design of the compressor. The phasor triangle model may provide an alternative method for the compressor design and matching with the cold finger.

Revegetation and management of tailings sand slopes from tar sand extraction: 1978 results

Energy Technology Data Exchange (ETDEWEB)

Rowell, M J

1979-01-01

The results are reported of research into the revegetation of two areas on a steeply sloping dike composed of tailings sand from tar sand extraction at the Great Canadian Oil Sand Limited plant at Fort McMurray, Alberta. One area was seeded with three pasture grasses and two legumes in 1971 after the slope surface had been mixed with peat to a depth of 15 cm. A second area had been amended with peat or peat and overburden and differing rates of fertilizer added. A mix containing nine grasses, four legumes, and oats, as a companion crop, was seeded in July 1976. The objectives of the research were to study methods for the establishment of a stable vegetative cover that would prevent erosion of the slope and, in time, might become a self maintaining unit. Tillage of soil amendments to a depth of 15 cm and 30 cm were compared in promoting deeper rooting and stabilizing of the slope.

Exploiting publicly available biological and biochemical information for the discovery of novel short linear motifs.

KAUST Repository

Sayadi, Ahmed

2011-07-20

The function of proteins is often mediated by short linear segments of their amino acid sequence, called Short Linear Motifs or SLiMs, the identification of which can provide important information about a protein function. However, the short length of the motifs and their variable degree of conservation makes their identification hard since it is difficult to correctly estimate the statistical significance of their occurrence. Consequently, only a small fraction of them have been discovered so far. We describe here an approach for the discovery of SLiMs based on their occurrence in evolutionarily unrelated proteins belonging to the same biological, signalling or metabolic pathway and give specific examples of its effectiveness in both rediscovering known motifs and in discovering novel ones. An automatic implementation of the procedure, available for download, allows significant motifs to be identified, automatically annotated with functional, evolutionary and structural information and organized in a database that can be inspected and queried. An instance of the database populated with pre-computed data on seven organisms is accessible through a publicly available server and we believe it constitutes by itself a useful resource for the life sciences (http://www.biocomputing.it/modipath).

Developing new markets for oil sands products

International Nuclear Information System (INIS)

Crandall, G.

2004-01-01

This paper presents a review by Purvin and Gertz of western Canadian crude oil supply. This energy consulting firm provides advise to the energy sector. It suggests that oil sands production will surpass declining conventional production. Oil sands supply includes bitumen, synthetic crude oil (SCO), and diluent. It is forecasted that oil sands will increase from 42 per cent of western supply in 2002 to 78 per cent in 2015. The potential of Alberta's oil sands was discussed along with a recent study of refined products and petrochemicals from bitumen. Upgrading, refining and petrochemical case studies were presented. The author examined if a Canadian oil sands upgrading project with high capital costs can be competitive with competing projects in the United States and internationally. In addition to supply and demand issues, the presentation examined infrastructure capability and market potential in the United States. The economic potential and risks of preferred business cases compared to upgrading to SCO were also evaluated. 15 figs

The behavior of gaseous iodine in sand

International Nuclear Information System (INIS)

Takahashi, Kanji

1974-01-01

Radioactive iodine gas was passed through 10 different sands collected at rivers and hills. The relation between the amount of the loaded gas and the amount of adsorbed gas was determined at room temperature, 50 -- 60 0 C, and 90 -- 100 0 C under humidity of 2 sand. This amount was about 1 -- 3 times as much as that of monomolecular membrane adsorption, 0.2 -- 0.3 μg/cm 2 . The decrease of adsorption amount that accompanies the increase of humidity is attributable to the decrease of effective surface area of sand due to the presence of water. The transport of iodine in sand was studied by passing gaseous iodine through a glass tubing packed with sand. The distribution in the flow direction of iodine indicated that the ease of desorption depends upon the situation of adsorption. Easily desorbed case was named Henry type adsorption. Hardly desorbed case was named absorption type. Discussion is made on experimental results. (Fukutomi, T.)

Investigations of the Influence of the Matrix Recycling on Properties of the Moulding Sand with Geopol 618 Binder

Directory of Open Access Journals (Sweden)

J. Kamińska

2013-01-01

Full Text Available Self-hardening moulding sands with water-glass hardened by liquid esters are applied in several foundry plants for making moulds for the production of heavy iron and steel castings. The main good point of this process is a low cost of sands. However, on account of a lowsusceptibility of this moulding sand for the matrix reclamation the fraction of sands originated from the reclamation is limited.The investigations presented in this work were aimed at the determination of the addition of the reclaimed material, obtained in the dry mechanical reclamation, on properties of the moulding sand with the Geopol 618 binder, which is water-glass modified by polymers and hardened by esters.

Investigations of the Influence of the Matrix Recycling on Properties of the Moulding Sand with Geopol 618 Binder

Directory of Open Access Journals (Sweden)

Kamińska J.

2013-03-01

Full Text Available Self-hardening moulding sands with water-glass hardened by liquid esters are applied in several foundry plants for making moulds for the production of heavy iron and steel castings. The main good point of this process is a low cost of sands. However, on account of a low susceptibility of this moulding sand for the matrix reclamation the fraction of sands originated from the reclamation is limited. The investigations presented in this work were aimed at the determination of the addition of the reclaimed material, obtained in the dry mechanical reclamation, on properties of the moulding sand with the Geopol 618 binder, which is water-glass modified by polymers and hardened by esters.

Bioaugmentation of flow-through sand filters

DEFF Research Database (Denmark)

Samuelsen, Elin Djurhuus

for degradation performances in flow-through sand columns, with the aim of identifying a suitable inoculant strain for future environmental applications. Another aim was to identify a suitable genetic marker to monitor phenoxy acid degradation in strain Sphingobium sp. PM2. We were not able to link motility...... and biofilm formation to the strains´ ability to adhere to sand. Nevertheless, a correlation was found between cell surface hydrophobicity and adhesion and overall degradation performances in flow-through sand columns. We identified S phingobium sp. PM2 as a promising inoculant strain, displaying efficient...... MCPA degradation for prolonged periods in flow-through sand columns. In an expression study of catabolic genes with putative roles in phenoxy acid degradation, we observed a marked upregulation of catabolic genes cadA and tfdC upon exposure to MCPA, 2,4-D, dichlorprop and mecoprop in strain PM2, which...

Active binder content as a factor of the control system of the moulding sand quality

Directory of Open Access Journals (Sweden)

J. Jakubski

2011-01-01

Full Text Available One of the modern methods of the production optimisation are artificial neural networks. Neural networks are gaining broader and broaderapplication in the foundry industry, among others for controlling melting processes in cupolas and in arc furnaces, for designing castingsand supply systems, for controlling moulding sand processing, for predicting properties of cast alloys or selecting parameters of pressurecastings. An attempt to apply neural networks for controlling the quality of bentonite moulding sands is presented in this paper. This is theassessment method of sands suitability by means of detecting correlations between their individual parameters. The presentedinvestigations were obtained by using the Statistica 9.0 program. The presented investigations were aimed at the selection of the neuralnetwork able to predict the active bentonite content in the moulding sand on the basis of this sand properties such as: permeability,compactibility and the compressive strength. An application of the Statistica program allowed to select automatically the type of networkproper for the representation of dependencies occurring in between the proposed moulding sand parameters. The most advantageousconditions were obtained for the uni-directional multi-layer perception (MLP network. Knowledge of the neural network sensitivity to individual moulding sand parameters, allowed to eliminate not essential ones.

Heavy crude and tar sands - the long-term oil reserve

Energy Technology Data Exchange (ETDEWEB)

Barnea, J

1984-10-01

It appears that heavy crude and tar sands occur in many sedimentary areas, and estimates of known world-wide quantities exceed those known for conventional light crude resources. Although there are not precise figures available, production could be as high as three million barrels per day, with Venezuela, the US, and Canada the largest producers. There are different scales to measure the costs of production because of differences in the quality of various types of heavy crude and tar sands. Economic development of these resources should banish fears of oil scarcity in the foreseeable future. A center for information exchange through international meetings and publications is under development.

Advanced testing and characterization of transportation soils and bituminous sands

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2007-12-01

Full Text Available This research study was intended to develop laboratory test procedures for advance testing and characterization of fine-grained cohesive soils and oil sand materials. The test procedures are based on typical field loading conditions and the loading...

Hydrophobic Sand Is a Non-Toxic Method of Urine Collection, Appropriate for Urinary Metal Analysis in the Rat

Directory of Open Access Journals (Sweden)

Jessica F. Hoffman

2017-10-01

Full Text Available Hydrophobic sand is a relatively new method of urine collection in the rodent, comparable to the established method using a metabolic cage. Urine samples are often used in rodent research, especially for biomarkers of health changes after internal contamination from embedded metals, such as in a model of a military shrapnel wound. However, little research has been done on the potential interference of hydrophobic sand with urine metal concentrations either by contamination from the sand particulate, or adsorption of metals from the urine. We compare urine collected from rats using the metabolic cage method and the hydrophobic sand method for differences in metal concentration of common urinary metals, and examine physical properties of the sand material for potential sources of contamination. We found minimal risk of internal contamination of the rat by hydrophobic sand, and no interference of the sand with several common metals of interest (cobalt, strontium, copper, and manganese, although we advise caution in studies of aluminum in urine.

Booming Sand Dunes

Science.gov (United States)

Vriend, Nathalie

"Booming" sand dunes are able to produce low-frequency sound that resembles a pure note from a music instrument. The sound has a dominant audible frequency (70-105 Hz) and several higher harmonics and may be heard from far distances away. A natural or induced avalanche from a slip face of the booming dune triggers the emission that may last for several minutes. There are various references in travel literature to the phenomenon, but to date no scientific explanation covered all field observations. This thesis introduces a new physical model that describes the phenomenon of booming dunes. The waveguide model explains the selection of the booming frequency and the amplification of the sound in terms of constructive interference in a confined geometry. The frequency of the booming is a direct function of the dimensions and velocities in the waveguide. The higher harmonics are related to the higher modes of propagation in the waveguide. The experimental validation includes quantitative field research at the booming dunes of the Mojave Desert and Death Valley National Park. Microphone and geophone recordings of the acoustic and seismic emission show a variation of booming frequency in space and time. The analysis of the sensor data quantifies wave propagation characteristics such as speed, dispersion, and nonlinear effects and allows the distinction between the source mechanism of the booming and the booming itself. The migration of sand dunes results from a complicated interplay between dune building, wind regime, and precipitation. The morphological and morphodynamical characteristics of two field locations are analyzed with various geophysical techniques. Ground-penetrating radar images the subsurface structure of the dunes and reveal a natural, internal layering that is directly related to the history of dune migration. The seismic velocity increases abruptly with depth and gradually increases with downhill position due to compaction. Sand sampling shows local

Oil sands economic impacts Canada : CERI report : backgrounder

International Nuclear Information System (INIS)

2005-09-01

Oil sands production now accounts for 1 out of every 2 barrels of supply in Western Canada. It is anticipated that Alberta's oil sands sector will experience significant growth over the next few decades. This paper provided an outline of the challenges and economic impacts resulting from oil sands development in Canada. Alberta's oil sands reserves are estimated at 175 billion barrels that are deemed economically recoverable using current technology. At current production levels, reserves will sustain production of 2.5 million barrels per day for the next 200 years. A study by the Canadian Energy Research Institute (CERI) has forecast $100 billion in investment for the 2000-2020 period. Numerous companies hold leases and are planning new projects. A number of recent advances in oil sands technology are expected to further reduce costs as development matures. A royalty and tax regime that provides long-term fiscal certainty is a key factor that supports current oil sands growth forecasts. The CERI study has indicated that economic spinoffs from oil sands development relate to employment generated outside of Alberta, and that the largest percentage of government revenue accrues to the federal government. However, development may be constrained because the pace of growth in the sector may exceed underlying infrastructure related to roads, housing and municipal services. An adequate workforce of qualified trades and technical and professional people is also crucial. Several pipeline projects have been proposed to deliver oil sands crudes to new markets over the next decade. It was concluded that the billions of dollars invested in oil sands in Alberta will contribute to the economic prosperity of the entire country. 11 figs

Provenance and recycling of Arabian desert sand

Science.gov (United States)

Garzanti, Eduardo; Vermeesch, Pieter; Andò, Sergio; Vezzoli, Giovanni; Valagussa, Manuel; Allen, Kate; Kadi, Khalid A.; Al-Juboury, Ali I. A.

2013-05-01

This study seeks to determine the ultimate origin of aeolian sand in Arabian deserts by high-resolution petrographic and heavy-mineral techniques combined with zircon U-Pb geochronology. Point-counting is used here as the sole method by which unbiased volume percentages of heavy minerals can be obtained. A comprehensive analysis of river and wadi sands from the Red Sea to the Bitlis-Zagros orogen allowed us to characterize all potential sediment sources, and thus to quantitatively constrain provenance of Arabian dune fields. Two main types of aeolian sand can be distinguished. Quartzose sands with very poor heavy-mineral suites including zircon occupy most of the region comprising the Great Nafud and Rub' al-Khali Sand Seas, and are largely recycled from thick Lower Palaeozoic quartzarenites with very minor first-cycle contributions from Precambrian basement, Mesozoic carbonate rocks, or Neogene basalts. Instead, carbonaticlastic sands with richer lithic and heavy-mineral populations characterize coastal dunes bordering the Arabian Gulf from the Jafurah Sand Sea of Saudi Arabia to the United Arab Emirates. The similarity with detritus carried by the axial Tigris-Euphrates system and by transverse rivers draining carbonate rocks of the Zagros indicates that Arabian coastal dunes largely consist of far-travelled sand, deposited on the exposed floor of the Gulf during Pleistocene lowstands and blown inland by dominant Shamal northerly winds. A dataset of detrital zircon U-Pb ages measured on twelve dune samples and two Lower Palaeozoic sandstones yielded fourteen identical age spectra. The age distributions all show a major Neoproterozoic peak corresponding to the Pan-African magmatic and tectonic events by which the Arabian Shield was assembled, with minor late Palaeoproterozoic and Neoarchean peaks. A similar U-Pb signature characterizes also Jafurah dune sands, suggesting that zircons are dominantly derived from interior Arabia, possibly deflated from the Wadi al

TYPE OF LIGHT IN SAND FLY CAPTURES (DIPTERA:PSYCHODIDAE

Directory of Open Access Journals (Sweden)

VERÔNICA DE LOURDES SIERPE JERALDO

2012-09-01

Full Text Available The number of cases of visceral leishmaniasis in Brazil has been gradually increasing, and one of the strategies to reduce the transmission of this disease is based on the control of the adult forms of its vectors. It is therefore of great epidemiological importance to develop more refined methods for monitoring and controlling its vectors, which are the phlebotomine sand flies, or biting midges. The present study compares the attraction exercised by UV light in comparison with conventional incandescent, or white, light in catching phlebotomine sand flies. Traps baited with UV light caught higher numbers of these flies than traps baited with white light, indicating the potential use of UV light, especially in locations of low demographic density of the flies.

Experimental investigation of sanding propensity for the Andrew completion

Energy Technology Data Exchange (ETDEWEB)

Venkitaraman, A.; Li, H. [Schlumberger Perforating and Testing Center (United Kingdom); Leonard, A. J.; Bowden, P. R. [BP Exploration (United Kingdom)

1998-12-31

A series of laboratory experiments were performed on three reservoir core samples selected from two plot wells to confirm the likelihood of sand production during the completion phase of the planned Andrew horizontal wells, and to perform risk analysis of formation failure at the time of underbalance perforation, and expected producing conditions. CT scans revealed no perforation failure, and the core samples did not show any propensity to produce sand during single-phase oil flow. Transient sand production was observed when water cut was introduced, but sand production declined as the percentage of water cut was increased. There was no evidence of sand production in the core samples during depletion testing either, and the wells were subsequently completed with perforated cemented liners without sand control. No sand problems have been encountered in two years of production, with some wells in water cut and declined reservoir pressure of 200 psi. 8 refs., 3 tabs., 5 figs.

Nuclear energy in the oils sands

International Nuclear Information System (INIS)

Arsenault, J.E.

2014-01-01

The major Canadian oil sands are located in Alberta and Saskatchewan, with most production from the strata along the Athabasca River in Alberta. The economically recoverable oil sands reserves are estimated to be 168 billion barrels which at a current production rate of 1.8 million barrels per day (2012), are projected to last a very long time. Canada has been blessed with vast energy resources which make it potentially energy-independent and able to provide significant exports but there are concerns that their development cannot be managed in a wholly acceptable manner. Comparable concerns have been applied to nuclear energy in the past and in recent times to the oil sands. The technologies associated with these energy sources have always been controversial because they are at the confluence of economics and politics where finding a balance between risk and reward is difficult. So it should be no surprise that when these technologies get linked together in certain proposals their prospect for success is doubly difficult. The possible use of nuclear energy for production of oil from the oil sands dates back to the late 1950s, when an experiment to mine the oil by detonating an underground nuclear device was proposed. It was predicted that the heat and pressure released from such a device would create a large cavern into which oil would flow, and from where it would be pumped to the surface. Almost at the same time, oil sands research using conventional sources of energy had culminated with the development of practical refining processes, essentially those still in use today. These methods require large amounts of heat energy in the form of hot water and steam. In this century nuclear energy was proposed as the source for the heat required by the oil sands production processes. To date neither of these nuclear proposals for oil sands projects have been successful, because the economic and political balance could not be struck. (author)

The provenance of Taklamakan desert sand

Science.gov (United States)

Rittner, Martin; Vermeesch, Pieter; Carter, Andrew; Bird, Anna; Stevens, Thomas; Garzanti, Eduardo; Andò, Sergio; Vezzoli, Giovanni; Dutt, Ripul; Xu, Zhiwei; Lu, Huayu

2016-03-01

Sand migration in the vast Taklamakan desert within the Tarim Basin (Xinjiang Uyghur Autonomous region, PR China) is governed by two competing transport agents: wind and water, which work in diametrically opposed directions. Net aeolian transport is from northeast to south, while fluvial transport occurs from the south to the north and then west to east at the northern rim, due to a gradual northward slope of the underlying topography. We here present the first comprehensive provenance study of Taklamakan desert sand with the aim to characterise the interplay of these two transport mechanisms and their roles in the formation of the sand sea, and to consider the potential of the Tarim Basin as a contributing source to the Chinese Loess Plateau (CLP). Our dataset comprises 39 aeolian and fluvial samples, which were characterised by detrital-zircon U-Pb geochronology, heavy-mineral, and bulk-petrography analyses. Although the inter-sample differences of all three datasets are subtle, a multivariate statistical analysis using multidimensional scaling (MDS) clearly shows that Tarim desert sand is most similar in composition to rivers draining the Kunlun Shan (south) and the Pamirs (west), and is distinctly different from sediment sources in the Tian Shan (north). A small set of samples from the Junggar Basin (north of the Tian Shan) yields different detrital compositions and age spectra than anywhere in the Tarim Basin, indicating that aeolian sediment exchange between the two basins is minimal. Although river transport dominates delivery of sand into the Tarim Basin, wind remobilises and reworks the sediment in the central sand sea. Characteristic signatures of main rivers can be traced from entrance into the basin to the terminus of the Tarim River, and those crossing the desert from the south to north can seasonally bypass sediment through the sand sea. Smaller ephemeral rivers from the Kunlun Shan end in the desert and discharge their sediment there. Both river run

Nuclear energy in the oils sands

Energy Technology Data Exchange (ETDEWEB)

Arsenault, J.E.

2014-09-15

The major Canadian oil sands are located in Alberta and Saskatchewan, with most production from the strata along the Athabasca River in Alberta. The economically recoverable oil sands reserves are estimated to be 168 billion barrels which at a current production rate of 1.8 million barrels per day (2012), are projected to last a very long time. Canada has been blessed with vast energy resources which make it potentially energy-independent and able to provide significant exports but there are concerns that their development cannot be managed in a wholly acceptable manner. Comparable concerns have been applied to nuclear energy in the past and in recent times to the oil sands. The technologies associated with these energy sources have always been controversial because they are at the confluence of economics and politics where finding a balance between risk and reward is difficult. So it should be no surprise that when these technologies get linked together in certain proposals their prospect for success is doubly difficult. The possible use of nuclear energy for production of oil from the oil sands dates back to the late 1950s, when an experiment to mine the oil by detonating an underground nuclear device was proposed. It was predicted that the heat and pressure released from such a device would create a large cavern into which oil would flow, and from where it would be pumped to the surface. Almost at the same time, oil sands research using conventional sources of energy had culminated with the development of practical refining processes, essentially those still in use today. These methods require large amounts of heat energy in the form of hot water and steam. In this century nuclear energy was proposed as the source for the heat required by the oil sands production processes. To date neither of these nuclear proposals for oil sands projects have been successful, because the economic and political balance could not be struck. (author)

Gases Emission From Surface Layers of Sand Moulds and Cores Stored Under the Humid Air Conditions

Directory of Open Access Journals (Sweden)

Kaźnica N.

2017-12-01

Full Text Available A large number of defects of castings made in sand moulds is caused by gases. There are several sources of gases: gases emitted from moulds, cores or protective coatings during pouring and casting solidification; water in moulding sands; moisture adsorbed from surroundings due to atmospheric conditions changes. In investigations of gas volumetric emissions of moulding sands amounts of gases emitted from moulding sand were determined - up to now - in dependence of the applied binders, sand grains, protective coatings or alloys used for moulds pouring. The results of investigating gas volumetric emissions of thin-walled sand cores poured with liquid metal are presented in the hereby paper. They correspond to the surface layer in the mould work part, which is decisive for the surface quality of the obtained castings. In addition, cores were stored under conditions of a high air humidity, where due to large differences in humidity, the moisture - from surroundings - was adsorbed into the surface layer of the sand mould. Due to that, it was possible to asses the influence of the adsorbed moisture on the gas volumetric emission from moulds and cores surface layers by means of the new method of investigating the gas emission kinetics from thin moulding sand layers heated by liquid metal. The results of investigations of kinetics of the gas emission from moulding sands with furan and alkyd resins as well as with hydrated sodium silicate (water glass are presented. Kinetics of gases emissions from these kinds of moulding sands poured with Al-Si alloy were compared.

Geochemical characteristics of oil sands fluid petroleum coke

International Nuclear Information System (INIS)

Nesbitt, Jake A.; Lindsay, Matthew B.J.; Chen, Ning

2017-01-01

The geochemical characteristics of fluid petroleum coke from the Athabasca Oil Sands Region (AOSR) of northern Alberta, Canada were investigated. Continuous core samples were collected to 8 m below surface at several locations (n = 12) from three coke deposits at an active oil sands mine. Bulk elemental analyses revealed the coke composition was dominated by C (84.2 ± 2.3 wt%) and S (6.99 ± 0.26 wt%). Silicon (9210 ± 3000 mg kg"−"1), Al (5980 ± 1200 mg kg"−"1), Fe (4760 ± 1200 mg kg"−"1), and Ti (1380 ± 430 mg kg"−"1) were present in lesser amounts. Vanadium (1280 ± 120 mg kg"−"1) and Ni (230 ± 80 mg kg"−"1) exhibited the highest concentrations among potentially-hazardous minor and trace elements. Sequential extractions revealed potential for release of these metals under field-relevant conditions. Synchrotron powder X-ray diffraction revealed the presence of Si and Ti oxides, organically-complexed V and hydrated Ni sulfate, and provided information about the asphaltenic carbon matrix. X-ray absorption near edge structure (XANES) spectroscopy at the V and Ni K-edges revealed that these metals were largely hosted in porphyrins and similar organic complexes throughout coke grains. Minor differences among measured V and Ni K-edge spectra were largely attributed to slight variations in local coordination of V(IV) and Ni(II) within these organic compounds. However, linear combination fits were improved by including reference spectra for inorganic phases with octahedrally-coordinated V(III) and Ni(II). Sulfur and Fe K-edge XANES confirmed that thiophenic coordination and pyritic-ilmenitic coordination are predominant, respectively. These results provide new information on the geochemical and mineralogical composition of oil sands fluid petroleum coke and improve understanding of potential controls on associated water chemistry. - Highlights: • Oil sands fluid petroleum coke contains wide range of major, minor and

Sediment Source Fingerprinting of the Lake Urmia Sand Dunes.

Science.gov (United States)

Ahmady-Birgani, Hesam; Agahi, Edris; Ahmadi, Seyed Javad; Erfanian, Mahdi

2018-01-09

Aeolian sand dunes are continuously being discovered in inner dry lands and coastal areas, most of which have been formed over the Last Glacial Maximum. Presently, due to some natural and anthropogenic implications on earth, newly-born sand dunes are quickly emerging. Lake Urmia, the world's second largest permanent hypersaline lake, has started shrinking, vast lands comprising sand dunes over the western shore of the lake have appeared and one question has been playing on the minds of nearby dwellers: where are these sand dunes coming from, What there was not 15 years ago!! In the present study, the determination of the source of the Lake Urmia sand dunes in terms of the quantifying relative contribution of each upstream geomorphological/lithological unit has been performed using geochemical fingerprinting techniques. The findings demonstrate that the alluvial and the fluvial sediments of the western upstream catchment have been transported by water erosion and they accumulated in the lower reaches of the Kahriz River. Wind erosion, as a secondary agent, have carried the aeolian sand-sized sediments to the sand dune area. Hence, the Lake Urmia sand dunes have been originating from simultaneous and joint actions of alluvial, fluvial and aeolian processes.

Varying Inundation Regimes Differentially Affect Natural and Sand-Amended Marsh Sediments.

Directory of Open Access Journals (Sweden)

C Wigand

Full Text Available Climate change is altering sea level rise rates and precipitation patterns worldwide. Coastal wetlands are vulnerable to these changes. System responses to stressors are important for resource managers and environmental stewards to understand in order to best manage them. Thin layer sand or sediment application to drowning and eroding marshes is one approach to build elevation and resilience. The above- and below-ground structure, soil carbon dioxide emissions, and pore water constituents in vegetated natural marsh sediments and sand-amended sediments were examined at varying inundation regimes between mean sea level and mean high water (0.82 m NAVD88 to 1.49 m NAVD88 in a field experiment at Laws Point, part of the Plum Island Sound Estuary (MA. Significantly lower salinities, pH, sulfides, phosphates, and ammonium were measured in the sand-amended sediments than in the natural sediments. In natural sediments there was a pattern of increasing salinity with increasing elevation while in the sand-amended sediments the trend was reversed, showing decreasing salinity with increasing elevation. Sulfide concentrations generally increased from low to high inundation with highest concentrations at the highest inundation (i.e., at the lowest elevations. High pore water phosphate concentrations were measured at low elevations in the natural sediments, but the sand-amended treatments had mostly low concentrations of phosphate and no consistent pattern with elevation. At the end of the experiment the lowest elevations generally had the highest measures of pore water ammonium. Soil carbon dioxide emissions were greatest in the sand-amended mesocosms and at higher elevations. Differences in coarse root and rhizome abundances and volumes among the sediment treatments were detected with CT imaging, but by 20 weeks the natural and sand-amended treatments showed similar total belowground biomass at the intermediate and high elevations. Although differences in

Description of Pintomyia (Pifanomyia falcaorum sp. n. (Diptera: Psychodidae: Phlebotominae, a Fossil Sand Fly from Dominican Amber

Directory of Open Access Journals (Sweden)

Reginaldo Peçanha Brazil

2002-06-01

Full Text Available A new species of sand fly, Pintomyia (Pifanomyia falcaorum is described from an amber originated from the northern mountain range of Dominican Republic. The male sand fly specimen is well preserved and most features used in Phlebotominae taxonomy are seen with remarkable clarity.

Changes in active eolian sand at northern Coachella Valley, California

Science.gov (United States)

Katra, Itzhak; Scheidt, Stephen; Lancaster, Nicholas

2009-04-01

Climate variability and rapid urbanization have influenced the sand environments in the northern Coachella Valley throughout the late 20th century. This paper addresses changes in the spatial relationships among different sand deposits at northern Coachella Valley between two recent time periods by using satellite data acquired from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER). The approach employed here, involving multispectral thermal infrared (TIR) data and spectral mixture analysis, has shown that the major sand deposits can be spatially modeled at northern Coachella Valley. The "coarse-grained (quartz-rich) sand" deposit is associated with active eolian sand, and the "mixed sandy soil" and "fine-grained (quartz-rich) sand" deposits are associated with inactive eolian sand. The fractional abundance images showed a significant decrease between 2000 and 2006 in the percentage of active sand in the major depositional area for fluvial sediment, the Whitewater River, but also in two downwind areas: the Whitewater and Willow Hole Reserves. The pattern of the active sand appears to be related to variations in annual precipitation (wet and dry years) and river discharge in the northern Coachella Valley. We suggest here that recent human modifications to the major watercourses that supply sand affect the capability of fluvial deposition areas to restore sediments over time and consequently the responses of the sand transport system to climate change, becoming more sensitive to dry years where areas of active sand may shrink, degrade, and/or stabilize faster. The approach utilized in this study can be advantageous for future monitoring of sand in the northern Coachella Valley for management of these and similar environments.

Namibia : triaxial test on sand

DEFF Research Database (Denmark)

Steenfelt, Jørgen S.; Jacobsen, Kim P.

In connection with a harbour project the friction angle of a fine sand is required. On Friday 13 March 1998 the Danish Geotechnical Institute (DGI) delivered app. 2.5 kg sand for testing at the Geotechnical Engineering Laboratory, Aalborg University. The present Data Report summarises the results...... of two CID, isotropically consolidated, drained triaxial tests carried out according to the instructions in DG1 letter dated 13 March 1998....

Pattern formation - Instabilities in sand ripples

DEFF Research Database (Denmark)

Hansen, J. L.; v. Hecke, M.; Haaning, A.

2001-01-01

Sand ripples are seen below shallow wavy water and are formed whenever water oscillates over a bed of sand. Here we analyse the instabilities that can upset this perfect patterning when the ripples are subjected to large changes in driving amplitude or frequency, causing them to deform both...

Southeast Florida Sediment Assessment and Needs Determination (SAND) Study

Science.gov (United States)

2014-09-01

sand with some shell beds, sandstone , and limestone *Miami Limestone 0 to 80 ft Oolitic limestone, quartz sand, and sandstone Anastasia 0 to 100 ft...Sand, shell beds, marl, calcareous sandstone (coquina/calcarenite) Fort Thompson 0 to 80 ft Silty limestone, silty sand, clayey marl, shell marl...highly- to moderately- weathered quartzose sandstone , and highly-weathered (saprolitic) to moderately-weathered hard limestone. North-south and

Modelling the behavior of an oil saturated sand

International Nuclear Information System (INIS)

Evgin, E.; Altaee, A.; Lord, S.; Konuk, I.

1990-01-01

The experiments carried out in an earlier study show the oil contamination affects the strength and deformation characteristics of a crushed quartz sand. In the present study, a mathematical soil model is used to simulate the mechanical behavior of the same sand. The model parameters are determined for both clean and oil contaminated soil. Simulations are made for the stress-strain behavior of the soil in drained and undrained conventional traixial compression tests. In order to illustrate the effect of changes in the soil properties on the behavior of an engineering structure, a finite element analysis is carried out. In this paper comparative results are presented to show the differences in the behavior of a foundation resting on a clean sand, on an oil contaminated sand, and on a sand contaminated locally

Oblique second-order sand transport pathways on an intertidal sand flat in a natural tidal inlet system

DEFF Research Database (Denmark)

Ernstsen, Verner Brandbyge; Lefebvre, Alice; Kroon, Aart

2013-01-01

tide, sand is transported along ESE-oriented pathways across the intertidal flat towards the inner tidal basin. During the late stages of ebb tide, sand is transported in drainage channels (WSWoriented) from the intertidal flat towards the inlet channel. During storm events with winds from SW, wave...

Oil sands supply outlook

International Nuclear Information System (INIS)

Dunbar, R.

2004-01-01

In March 2004, The Canadian Energy Research Institute released a report on the expected future supply from Alberta's oil sands. The report indicates that the future for the already well-established oil sands industry is promising, particularly given the outlook for oil prices. The challenges facing the industry include higher industry supply costs and the need for innovative commercial and technological solutions to address the risks of irregularities and changes in crude oil prices. In 2003, the industry produced 874 thousand barrels per day of synthetic crude oil and unprocessed crude bitumen. This represents 35 per cent of Canada's total oil production. Current production capacity has increased to 1.0 million barrels per day (mbpd) due to new projects. This number may increase to 3.5 mbpd by 2017. Some new projects may be deferred due to the higher raw bitumen and synthetic crude oil supply costs. This presentation provided supply costs for a range of oil sands recovery technologies and production projections under various business scenarios. tabs., figs

Reuse of waste cutting sand at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Mathews, S.; Wilson, K.

1998-01-01

Lawrence Livermore National Laboratory (LLNL) examined the waste stream from a water jet cutting operation, to evaluate the possible reuse of waste garnet sand. The sand is a cutting agent used to shape a variety of materials, including metals. Nearly 70,000 pounds of waste sand is generated annually by the cutting operation. The Environmental Protection Department evaluated two potential reuses for the spent garnet sand: backfill in utility trenches; and as a concrete constituent. In both applications, garnet waste would replace the sand formerly purchased by LLNL for these purposes. Findings supported the reuse of waste garnet sand in concrete, but disqualified its proposed application as trench backfill. Waste sand stabilized in a concrete matrix appeared to present no metals-leaching hazard; however, unconsolidated sand in trenches could potentially leach metals in concentrations high enough to threaten ground water quality. A technical report submitted to the San Francisco Bay Regional Water Quality Control Board was reviewed and accepted by that body. Reuse of waste garnet cutting sand as a constituent in concrete poured to form walkways and patios at LLNL was approved

Computation of Normal Conducting and Superconducting Linear Accelerator (LINAC) Availabilities

International Nuclear Information System (INIS)

Haire, M.J.

2000-01-01

A brief study was conducted to roughly estimate the availability of a superconducting (SC) linear accelerator (LINAC) as compared to a normal conducting (NC) one. Potentially, SC radio frequency cavities have substantial reserve capability, which allows them to compensate for failed cavities, thus increasing the availability of the overall LINAC. In the initial SC design, there is a klystron and associated equipment (e.g., power supply) for every cavity of an SC LINAC. On the other hand, a single klystron may service eight cavities in the NC LINAC. This study modeled that portion of the Spallation Neutron Source LINAC (between 200 and 1,000 MeV) that is initially proposed for conversion from NC to SC technology. Equipment common to both designs was not evaluated. Tabular fault-tree calculations and computer-event-driven simulation (EDS) computer computations were performed. The estimated gain in availability when using the SC option ranges from 3 to 13% under certain equipment and conditions and spatial separation requirements. The availability of an NC LINAC is estimated to be 83%. Tabular fault-tree calculations and computer EDS modeling gave the same 83% answer to within one-tenth of a percent for the NC case. Tabular fault-tree calculations of the availability of the SC LINAC (where a klystron and associated equipment drive a single cavity) give 97%, whereas EDS computer calculations give 96%, a disagreement of only 1%. This result may be somewhat fortuitous because of limitations of tabular fault-tree calculations. For example, tabular fault-tree calculations can not handle spatial effects (separation distance between failures), equipment network configurations, and some failure combinations. EDS computer modeling of various equipment configurations were examined. When there is a klystron and associated equipment for every cavity and adjacent cavity, failure can be tolerated and the SC availability was estimated to be 96%. SC availability decreased as

Identification of Algerian Field-Caught Phlebotomine Sand Fly Vectors by MALDI-TOF MS.

Directory of Open Access Journals (Sweden)

Ismail Lafri

2016-01-01

Full Text Available Phlebotomine sand flies are known to transmit Leishmania parasites, bacteria and viruses that affect humans and animals in many countries worldwide. Precise sand fly identification is essential to prevent phlebotomine-borne diseases. Over the past two decades, progress in matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS has emerged as an accurate tool for arthropod identification. The objective of the present study was to investigate the usefulness of MALDI-TOF MS as a tool for identifying field-caught phlebotomine.Sand flies were captured in four sites in north Algeria. A subset was morphologically and genetically identified. Six species were found in these areas and a total of 28 stored frozen specimens were used for the creation of the reference spectrum database. The relevance of this original method for sand fly identification was validated by two successive blind tests including the morphological identification of 80 new specimens which were stored at -80°C, and 292 unknown specimens, including engorged specimens, which were preserved under different conditions. Intra-species reproducibility and inter-species specificity of the protein profiles were obtained, allowing us to distinguish specimens at the gender level. Querying of the sand fly database using the MS spectra from the blind test groups revealed concordant results between morphological and MALDI-TOF MS identification. However, MS identification results were less efficient for specimens which were engorged or stored in alcohol. Identification of 362 phlebotomine sand flies, captured at four Algerian sites, by MALDI-TOF MS, revealed that the subgenus Larroussius was predominant at all the study sites, except for in M'sila where P. (Phlebotomus papatasi was the only sand fly species detected.The present study highlights the application of MALDI-TOF MS for monitoring sand fly fauna captured in the field. The low cost, reliability and

Augmenting Sand Simulation Environments through Subdivision and Particle Refinement

Science.gov (United States)

Clothier, M.; Bailey, M.

2012-12-01

Recent advances in computer graphics and parallel processing hardware have provided disciplines with new methods to evaluate and visualize data. These advances have proven useful for earth and planetary scientists as many researchers are using this hardware to process large amounts of data for analysis. As such, this has provided opportunities for collaboration between computer graphics and the earth sciences. Through collaboration with the Oregon Space Grant and IGERT Ecosystem Informatics programs, we are investigating techniques for simulating the behavior of sand. We are also collaborating with the Jet Propulsion Laboratory's (JPL) DARTS Lab to exchange ideas and gain feedback on our research. The DARTS Lab specializes in simulation of planetary vehicles, such as the Mars rovers. Their simulations utilize a virtual "sand box" to test how a planetary vehicle responds to different environments. Our research builds upon this idea to create a sand simulation framework so that planetary environments, such as the harsh, sandy regions on Mars, are more fully realized. More specifically, we are focusing our research on the interaction between a planetary vehicle, such as a rover, and the sand beneath it, providing further insight into its performance. Unfortunately, this can be a computationally complex problem, especially if trying to represent the enormous quantities of sand particles interacting with each other. However, through the use of high-performance computing, we have developed a technique to subdivide areas of actively participating sand regions across a large landscape. Similar to a Level of Detail (LOD) technique, we only subdivide regions of a landscape where sand particles are actively participating with another object. While the sand is within this subdivision window and moves closer to the surface of the interacting object, the sand region subdivides into smaller regions until individual sand particles are left at the surface. As an example, let's say

Phlebotomine sand flies (Diptera: Psychodidae in the Greek Aegean Islands: ecological approaches

Directory of Open Access Journals (Sweden)

Nikolaos Tsirigotakis

2018-02-01

Full Text Available Abstract Background Blood-sucking phlebotomine sand flies are the vectors of the protozoan parasites Leishmania spp. Different Phlebotomus species transmit different Leishmania species causing leishmaniases which are neglected diseases emerging/reemerging in new regions. Thirteen sand fly species, ten belonging to the medically important genus Phlebotomus and three belonging to Sergentomyia are known in Greece. An increasing number of human and dog cases are reported each year from all parts of the country including the Aegean Islands. However, no previous study has been conducted on the sand fly fauna on the islands, except for Rhodes and Samos. The aim of this study was to investigate sand fly species in eleven small Aegean islands; to understand species-specific relationships with environmental and climatic factors and to compare sand fly community parameters among islands. A risk analysis was carried out for each species using climatic and environmental variables. Results Nine sand fly species: Phlebotomus neglectus, P. tobbi, P. similis, P. simici, P. perfiliewi, P. alexandri, P. papatasi, Sergentomyia minuta and S. dentata, were collected from the islands studied. Phlebotomus (Adlerius sp. and Sergentomyia sp. specimens were also collected but not identified to the species level. There was a positive effect of distance from the sea on the abundance of P. neglectus, S. minuta and S. dentata, and a negative effect on the abundance of P. tobbi, P. simici and P. similis. In general, temperature preferences of sand fly populations were between 21 and 29 °C. Nevertheless, there were significant differences in terms of temperature and relative humidity preference ranges among species. The most important species found, P. neglectus, was indisputably the most adapted species in the study area with a very high reaction norm, favoring even the lower temperature and humidity ranges. Overall, the sand fly fauna in the islands was very rich but there

Potatoes and Trout: Maintaining Robust Agriculture and a Healthy Trout Fishery in the Central Sands of Wisconsin

Science.gov (United States)

Fienen, M. N.; Bradbury, K. R.; Kniffin, M.; Barlow, P. M.; Krause, J.; Westenbroek, S.; Leaf, A.

2015-12-01

The well-drained sandy soil in the Wisconsin Central Sands is ideal for growing potatoes, corn, and other vegetables. A shallow sand and gravel aquifer provides abundant water for agricultural irrigation but also supplies critical base flow to cold-water trout streams. These needs compete with one another, and stakeholders from various perspectives are collaborating to seek solutions. Stakeholders were engaged in providing and verifying data to guide construction of a groundwater flow model which was used with linear and sequential linear programming to evaluate optimal tradeoffs between agricultural pumping and ecologically based minimum base flow values. The connection between individual irrigation wells as well as industrial and municipal supply and streamflow depletion can be evaluated using the model. Rather than addressing 1000s of wells individually, a variety of well management groups were established through k-means clustering. These groups are based on location, potential impact, water-use categories, depletion potential, and other factors. Through optimization, pumping rates were reduced to attain mandated minimum base flows. This formalization enables exploration of possible solutions for the stakeholders, and provides a tool which is transparent and forms a basis for discussion and negotiation.

Understanding Colombian Amazonian white sand forests

NARCIS (Netherlands)

Peñuela-Mora, M.C.

2014-01-01

Although progress has been made in studies on white sand forests in the Amazon, there is still a considerable gap in our knowledge of the unique species composition of white sand forests and their structure and dynamics, especially in Western Amazon. This thesis aims to fill this gap by addressing

Drivers of drift sand dynamics; a reconstruction for the Wekeromse Zand, the Netherlands

Science.gov (United States)

Hendriks, Chantal; Sonneveld, Marthijn; Wallinga, Jakob

2013-04-01

Inland active drift sand landscapes are regarded as unique ecosystems of great historical and geomorphological value. Recent studies have highlighted the role of multiple factors in the initiation and stabilization of drift sand landscapes. To unravel the importance of different forcings (e.g. agricultural practices, climate) and their interplay, insight in the chronology of drift sand dynamics is essential. In this study, we aimed to reconstruct the dynamics of the drift sand landscape of the Wekeromse Zand (central Netherlands) and to develop a conceptual model to understand the processes involved. The Wekeromse Zand study area (370 ha) is located on the border of a central push moraine and is characterised by open active drift sands (14 ha) and vegetated hills and valleys. The surroundings are dominated by modern agricultural practices, and remnants from ancient iron age Celtic Field systems showing that the area has been in agricultural use since at least the Iron Age. For the study area we: i) analysed historical maps going back to the early 19th century, ii) performed a field survey to map the palaeolandscape (before drift sand activation) and iii) employed optically stimulated luminescence (OSL) dating of drift sand deposits on 11 samples from two locations to determine the timing of drift sand deposition. Analysis of the available topographic maps showed no substantial aeolean activity of the area outside its morphological boundaries. OSL dating revealed that two drift sand layers were deposited between 1373 and 1462 AD and between 1680 and 1780 AD. A layer with a higher organic matter content was found at one of the sites. This suggests that the Wekeromse Zand has known three relatively stable periods: i) a period between the start of the Holocene to the Late Medieval Period, ii) in between the Medieval climatic optimum and the climatic Maunder minimum, and iii) current situation. Despite the fact that agricultural activities occurred in this area from the

Water productivity analysis of sand dams irrigation farming in northern Ethiopia

Directory of Open Access Journals (Sweden)

Lorenzo Villani

2018-06-01

Full Text Available Water scarcity in drylands is the main problem that has to be tackled by farmers and practitioners that work in these areas. Climate change and increased and wealthier population are expected to put additional stress on the water resource. A large number of studies is calling to focus efforts to enhance water productivity (WP, and one of the most promising option is represented by water harvesting, the collection and storage of runoff water to be used for beneficially uses. Among the available technologies, sand dams are experiencing a renovated interest because of their relative simplicity and their potential. This research aims to deepen the knowledge about WP of water harvesting systems studying a sand dam irrigation system in Tigray, north Ethiopia, where farmers are getting used to this new technology. The research was carried out in the period March-April 2017, when farmers use sand dams water to irrigate off-season maize. We analysed a representative plot irrigated through a shallow well drilled in the sand dam aquifer, in terms of yield, Crop Water Productivity (CWP, Crop Water Productivity based on Evapotranspiration (CWP(ET and Economic Water Productivity (EWP, through field data analysis and a validated Aquacrop model. CWP(ET was found to be low (1.12 kg of grain per m3 of evapotranspired water, due by both inefficient water application and low soil fertility. Aquacrop model results showed that changing the irrigation schedule can increase CWP(ET up to 1.35 kg/m3 and EWP up to 3.94 birr/m3, but yield gap is mainly due to the low soil fertility. Interventions on soil fertility can raise yields from the original 3.3 up to 8.5 kg/ha, and thus CWP(ET and EWP up to 2.94 kg/m3 and 9.54 birr/m3 respectively. To enhance the effect of sand dams in northern Ethiopia, a set of measures, including conservation agriculture, is then proposed.

Elasticity of Moulding Sands – a Method of Reducing Core Cracking

Directory of Open Access Journals (Sweden)

Dobosz St. M.

2017-03-01

Full Text Available This paper focuses on mechanical properties of self hardening moulding sands with furfuryl and alkyd binders. Elasticity as a new parameter of moulding sands is investigated. With the use of presented testing equipment, it is possible to determine force kinetics and deformation of moulding sand in real time. The need for this kind of study comes from the modern casting industry. New foundries can be characterized with high intensity of production which is correlated with high level of mechanization and automatization of foundry processes. The increasingly common use of manipulators in production of moulds and cores can lead to generation of new types of flaws, caused by breakage in moulds and cores which could occur during mould assembly. Hence it is required that moulds and cores have high resistance to those kinds of factors, attributing it with the phenomenon of elasticity. The article describes the theoretical basis of this property, presents methods of measuring and continues earlier research.

Radiation protection in the mineral sands industry in New South Wales

International Nuclear Information System (INIS)

Carter, M.W.; Coundouris, A.N.

1993-01-01

The mineral sands industry in New South Wales (NSW) mines and concentrates the heavy minerals ilmenite, rutile, zircon and monazite; principally for export. Mineral sands concentrates contain small quantities of thorium and uranium series radionuclides and therefore are radioactive. The protection of workers, the public and the environment is a responsibility of mine operators. NSW Government Departments administer legislation, grant approvals and specify conditions for radiation protection. A summary of the history and current size of the industry is presented, together with current legislative and licensing activities. The paper reviews available literature on radiation measurements in the East coast mineral sands industry and re-interprets the earlier data in the light of the contemporary methodology of dose assessment. Some unpublished information and the results of some new surveys are also presented. A comparison is made with results that have been reported from Western Australia. Procedures for reducing radiation exposures are discussed and areas of future information needs are suggested. 17 refs., 6 refs., 3 tabs

Influence of relative density on the cyclic shear strength of sands

Directory of Open Access Journals (Sweden)

Arab A.

2018-01-01

Full Text Available This paper presents a laboratory study of the influence of relative density on the liquefaction potential of a soil. The study is based on undrained triaxial tests that were performed on samples with relative density Id = 0.15, 0.5 and 0.65. The article is composed of three parts. First, we present the materials and characteristics of the studied sands. the second part deals with the procedure and the device used. The third part studies the influence of the relative density on the liquefaction potential of the three sands (Hostun Rf, Chlef and Rass. This study also makes it possible to explore the influence of granulometry on the liquefaction potential. The results of the tests show that concordant results have been obtained which clearly show that the increase of the relative density leads to a significant improvement in the resistance to liquefaction of the sands. This effect is very significant when the initial relative density Id = 0.50 to Id = 0.65.

Trajectories of saltating sand particles behind a porous fence

Science.gov (United States)

Zhang, Ning; Lee, Sang Joon; Chen, Ting-Guo

2015-01-01

Trajectories of aeolian sand particles behind a porous wind fence embedded in a simulated atmospheric boundary layer were visualized experimentally, to investigate the shelter effect of the fence on sand saltation. Two sand samples, one collected from a beach (d = 250 μm) and the other from a desert (d = 100 μm), were tested in comparison with the previous studies of a 'no-fence' case. A wind fence (ε = 38.5%) was installed on a flat sand bed filled with each sand sample. A high-speed photography technique and the particle tracking velocimetry (PTV) method were employed to reconstruct the trajectories of particles saltating behind the fence. The collision processes of these sand particles were analyzed, momentum and kinetic energy transfer between saltating particles and ground surface were also investigated. In the wake region, probability density distributions of the impact velocities agree well with the pattern of no-fence case, and can be explained by a log-normal law. The horizontal component of impact velocity for the beach sand is decreased by about 54%, and about 76% for the desert sand. Vertical restitution coefficients of bouncing particles are smaller than 1.0 due to the presence of the wind fence. The saltating particles lose a large proportion of their energy during the collision process. These results illustrate that the porous wind fence effectively abates the further evolution of saltating sand particles.

Plant functional traits and diversity in sand dune ecosystems across different biogeographic regions

Science.gov (United States)

Mahdavi, P.; Bergmeier, E.

2016-07-01

Plant species of a functional group respond similarly to environmental pressures and may be expected to act similarly on ecosystem processes and habitat properties. However, feasibility and applicability of functional groups in ecosystems across very different climatic regions have not yet been studied. In our approach we specified the functional groups in sand dune ecosystems of the Mediterranean, Hyrcanian and Irano-Turanian phytogeographic regions. We examined whether functional groups are more influenced by region or rather by habitat characteristics, and identified trait syndromes associated with common habitat types in sand dunes (mobile dunes, stabilized dunes, salt marshes, semi-wet sands, disturbed habitats). A database of 14 traits, 309 species and 314 relevés was examined and trait-species, trait-plot and species-plot matrices were built. Cluster analysis revealed similar plant functional groups in sand dune ecosystems across regions of very different species composition and climate. Specifically, our study showed that plant traits in sand dune ecosystems are grouped reflecting habitat affiliation rather than region and species pool. Environmental factors and constraints such as sand mobility, soil salinity, water availability, nutrient status and disturbance are more important for the occurrence and distribution of plant functional groups than regional belonging. Each habitat is shown to be equipped with specific functional groups and can be described by specific sets of traits. In restoration ecology the completeness of functional groups and traits in a site may serve as a guideline for maintaining or restoring the habitat.

Predictive hydrogeochemical modelling of bauxite residue sand in field conditions.

Science.gov (United States)

Wissmeier, Laurin; Barry, David A; Phillips, Ian R

2011-07-15

The suitability of residue sand (the coarse fraction remaining from Bayer's process of bauxite refining) for constructing the surface cover of closed bauxite residue storage areas was investigated. Specifically, its properties as a medium for plant growth are of interest to ensure residue sand can support a sustainable ecosystem following site closure. The geochemical evolution of the residue sand under field conditions, its plant nutrient status and soil moisture retention were studied by integrated modelling of geochemical and hydrological processes. For the parameterization of mineral reactions, amounts and reaction kinetics of the mineral phases natron, calcite, tricalcium aluminate, sodalite, muscovite and analcime were derived from measured acid neutralization curves. The effective exchange capacity for ion adsorption was measured using three independent exchange methods. The geochemical model, which accounts for mineral reactions, cation exchange and activity corrected solution speciation, was formulated in the geochemical modelling framework PHREEQC, and partially validated in a saturated-flow column experiment. For the integration of variably saturated flow with multi-component solute transport in heterogeneous 2D domains, a coupling of PHREEQC with the multi-purpose finite-element solver COMSOL was established. The integrated hydrogeochemical model was applied to predict water availability and quality in a vertical flow lysimeter and a cover design for a storage facility using measured time series of rainfall and evaporation from southwest Western Australia. In both scenarios the sand was fertigated and gypsum-amended. Results show poor long-term retention of fertilizer ions and buffering of the pH around 10 for more than 5 y of leaching. It was concluded that fertigation, gypsum amendment and rainfall leaching alone were insufficient to render the geochemical conditions of residue sand suitable for optimal plant growth within the given timeframe. The

Potential of the application of the modified polysaccharides water solutions as binders of moulding sands

Directory of Open Access Journals (Sweden)

K. Kaczmarska

2015-10-01

Full Text Available The results of preliminary tests of selected properties of the moulding sands with the binder in the form of a 5 % water solution of the sodium salt of carboxymethyl starch (with a degree of substitution (DS of 0,2 and 0,87 arepresented in this study. The moulding sand properties such as permeability, abrasion resistance, tensile and bendingstrength - after curing - are shown in series of tests. The cure process was conducted in a field of electromagnetic radiation within the microwave range. The effect of the microwave treatment on the moulding sand was evaporating of water (solvent in a binder and cross-linking of the polymeric binder. As a result the cured moulding sands with particular properties, essential in the context of its application in the mould technology in the foundry industry, were obtained.

Test study on relation between thaw-collapse displacement of medium sand and negative friction of single pile

Energy Technology Data Exchange (ETDEWEB)

Zhou, G.; Yang, W. [China University of Mining and Technology, Xuzhou (China). College of Architecture and Civil Engineering

1999-11-01

Based on simulation tests, the change of thaw-collapse displacement of saturated medium sand and the relation between negative friction of single pile and thaw-collapse displacement are investigated . In the separating ice and thawing stages, the relation between separating ice surface displacement of sample and time is similarly linear, but the displacement is too small in the redistribution stage of grains. Corresponding to these two stages, the displacement of sample grain framework surface can be divided into similarly linear and non-linear factions. The contribution of the non-linear section comes from grain redistribution after thawing. The negative friction of single pile shows good linear relation following the thawing process. But the producing and increasing mechanisms of negative friction are not the same in the two stages. During the stage of grain redistribution, the displacement of sample grain framework surface occupies only 9.7% of the total displacement, while the negative friction has increased by 18% or so. 6 refs., 7 figs.

The Canadian oil sands--a sticky future

Energy Technology Data Exchange (ETDEWEB)

Cowtan, S A

1977-01-01

The oil sands have been known for 200 yr but only over the last decade have they been recognized as a potential major energy source for Canada. The study looks at the present GCOS plant, and briefly discusses Canada's future energy requirements and how she might fill those requirements from conventional and nonconventional sources, such as the Frontier areas, oil sands mining, oil sands in situ, and heavy oil. The economics and the future of these sources and the environment necessary for their development are analyzed.

Thermoluminescent dosimetric properties of Descalvado sand

International Nuclear Information System (INIS)

Teixeira, M.I.; Caldas, L.V.E.

2006-01-01

Sand samples proceeding from Descalvado, Sao Paulo, were studied with regard to their dosimetric properties using the thermoluminescence technique (TL) for high doses. These sand samples present steady physical and chemical characteristics to the end items, and they are used in the glass industry and for casting. The TL curves of the samples were obtained after an irradiation at the Gamma-Cell system ( 60 Co), of IPEN. The glow curves present two peaks at 80 C and 220 C approximately. Calibration curves were obtained for doses between 50 Gy and 5 kGy. The results indicate that the sand samples can be used for high-doses dosimetry in several areas of applications of ionizing radiation. (Author)

Thermoluminescent dosimetric properties of Descalvado sand

Energy Technology Data Exchange (ETDEWEB)

Teixeira, M.I.; Caldas, L.V.E

2006-07-01

Sand samples proceeding from Descalvado, Sao Paulo, were studied with regard to their dosimetric properties using the thermoluminescence technique (TL) for high doses. These sand samples present steady physical and chemical characteristics to the end items, and they are used in the glass industry and for casting. The TL curves of the samples were obtained after an irradiation at the Gamma-Cell system ({sup 60} Co), of IPEN. The glow curves present two peaks at 80 C and 220 C approximately. Calibration curves were obtained for doses between 50 Gy and 5 kGy. The results indicate that the sand samples can be used for high-doses dosimetry in several areas of applications of ionizing radiation. (Author)

Investigation of the bacterial communities associated with females of Lutzomyia sand fly species from South America.

Directory of Open Access Journals (Sweden)

Mauricio R V Sant'Anna

Full Text Available Phlebotomine sand flies are vectors of Leishmania that are acquired by the female sand fly during blood feeding on an infected mammal. Leishmania parasites develop exclusively in the gut lumen during their residence in the insect before transmission to a suitable host during the next blood feed. Female phlebotomine sand flies are blood feeding insects but their life style of visiting plants as well as animals, and the propensity for larvae to feed on detritus including animal faeces means that the insect host and parasite are exposed to a range of microorganisms. Thus, the sand fly microbiota may interact with the developing Leishmania population in the gut. The aim of the study was to investigate and identify the bacterial diversity associated with wild adult female Lutzomyia sand flies from different geographical locations in the New World. The bacterial phylotypes recovered from 16S rRNA gene clone libraries obtained from wild caught adult female Lutzomyia sand flies were estimated from direct band sequencing after denaturing gradient gel electrophoresis of bacterial 16 rRNA gene fragments. These results confirm that the Lutzomyia sand flies contain a limited array of bacterial phylotypes across several divisions. Several potential plant-related bacterial sequences were detected including Erwinia sp. and putative Ralstonia sp. from two sand fly species sampled from 3 geographically separated regions in Brazil. Identification of putative human pathogens also demonstrated the potential for sand flies to act as vectors of bacterial pathogens of medical importance in addition to their role in Leishmania transmission.

Experimental Study on Stress Monitoring of Sand-Filled Steel Tube during Impact Using Piezoceramic Smart Aggregates.

Science.gov (United States)

Du, Guofeng; Zhang, Juan; Zhang, Jicheng; Song, Gangbing

2017-08-22

The filling of thin-walled steel tubes with quartz sand can help to prevent the premature buckling of the steel tube at a low cost. During an impact, the internal stress of the quartz sand-filled steel tube column is subjected to not only axial force but also lateral confining force, resulting in complicated internal stress. A suitable sensor for monitoring the internal stress of such a structure under an impact is important for structural health monitoring. In this paper, piezoceramic Smart Aggregates (SAs) are embedded into a quartz Sand-Filled Steel Tube Column (SFSTC) to monitor the internal structural stress during impacts. The piezoceramic smart aggregates are first calibrated by an impact hammer. Tests are conducted to study the feasibility of monitoring the internal stress of a structure. The results reflect that the calibration value of the piezoceramic smart aggregate sensitivity test is in good agreement with the theoretical value, and the output voltage value of the piezoceramic smart aggregate has a good linear relationship with external forces. Impact tests are conducted on the sand-filled steel tube with embedded piezoceramic smart aggregates. By analyzing the output signal of the piezoceramic smart aggregates, the internal stress state of the structure can be obtained. Experimental results demonstrated that, under the action of impact loads, the piezoceramic smart aggregates monitor the compressive stress at different locations in the steel tube, which verifies the feasibility of using piezoceramic smart aggregate to monitor the internal stress of a structure.

Mitigating in situ oil sands carbon costs

Energy Technology Data Exchange (ETDEWEB)

Theriault, D.J.; Peterson, J. [Laricina Energy Ltd., Calgary, AB (Canada); Heinrichs, H. [Canadian Chemical Technology Inc., Calgary, AB (Canada)

2008-10-15

Carbon capture and sequestration is a complex problem with a variety of dimensions that need to be considered. The political, social, and regulatory pressures are forcing carbon costs on the oil sands industry in an effort to reduce the carbon footprint of oil sands operations. This paper reviewed the political, social, and regulatory pressures and obligations for the in-situ oil sands industry. It presented the views and insights of Laricina Energy on the carbon challenge. It also described the initiatives that Laricina Energy is taking to manage these imperatives and outlined the challenges the industry is facing. The purpose of the paper was to encourage dialogue and collaboration by the oil sands industry. The paper also described the dimensions of the carbon problem and how the industry can contribute to a solution. Last, the paper reviewed the parameters of carbon dioxide or greenhouse gas containment and storage issues. It was concluded that the regulatory and policy requirements need to be clarified so that industry understands the new business landscape as well as the requirements that influence the economics of in-situ oil sands development. 7 refs., 7 figs.

Aging effects on oil-contaminated Kuwaiti sand

International Nuclear Information System (INIS)

Al-Sanad, H.A.; Ismael, N.F.

1997-01-01

Large quantities of oil-contaminated sands resulted from the destruction of oil wells and the formation of oil lakes in Kuwait at the end of the Gulf Wa/r. A laboratory testing program was carried out to determine the geotechnical properties of this material and the effect of aging on their properties. Tests included direct shear, triaxial, and consolidation tests on clean and contaminated sand at the same relative density. The influence of aging was examined by testing uncontaminated sand after aging for one, three, and six months in natural environmental conditions. The results indicated increased strength and stiffness due to aging and a reduction of the oil content due to evaporation of volatile compounds. The factors that influence the depth of oil penetration in compacted sand columns were also examined including the type of oil, relative density, and the amount of fines

Performance of soft clay stabilized with sand columns treated by silica fume

Directory of Open Access Journals (Sweden)

Samueel Zeena

2018-01-01

Full Text Available In many road construction projects, if weak soil exists, then uncontrollable settlement and critical load carrying capacity are major difficult problems to the safety and serviceability of roads in these areas. Thus ground improvement is essential to achieve the required level of performance. The paper presents results of the tests of four categories. First category was performed on saturated soft bed of clay without any treatment, the second category shed light on the improvement achieved in loading carrying capacity and settlement as a result of reinforcing with conventional sand columns at area replacement ratio = 0.196. The third set investigates the bed reinforced by sand columns stabilized with dry silica fume at different percentages (3, 5 and 7% and the fourth set investigates the behavior of sand columns treated with slurry silica fume at two percentages (10 and 12%. All sand columns models were constructed at (R.D= 60%. Model tests were performed on bed of saturated soil prepared at undrained shear strength between 16-20 kPa for all models. For all cases, the model test was loaded gradually by stress increments up to failure. Stress deformation measurements are recorded and analyzed in terms of bearing improvement ratio and settlement reduction ratio. Optimum results were indicated from soil treated with sand columns stabilized with 7% dry silica fume at medium state reflecting the highest bearing improvement ratio (3.04 and the settlement reduction ratio (0.09 after 7 days curing. While soil treated with sand columns stabilized with 10% slurry silica fume provided higher bearing improvement ratio 3.13 with lower settlement reduction ratio of 0.57 after 7-days curing.

Laboratory observations of artificial sand and oil agglomerates

Science.gov (United States)

Jenkins, Robert L.; Dalyander, P. Soupy; Penko, Allison; Long, Joseph W.

2018-04-27

Sand and oil agglomerates (SOAs) form when weathered oil reaches the surf zone and combines with suspended sediments. The presence of large SOAs in the form of thick mats (up to 10 centimeters [cm] in height and up to 10 square meters [m2] in area) and smaller SOAs, sometimes referred to as surface residual balls (SRBs), may lead to the re-oiling of beaches previously affected by an oil spill. A limited number of numerical modeling and field studies exist on the transport and dynamics of centimeter-scale SOAs and their interaction with the sea floor. Numerical models used to study SOAs have relied on shear-stress formulations to predict incipient motion. However, uncertainty exists as to the accuracy of applying these formulations, originally developed for sand grains in a uniformly sorted sediment bed, to larger, nonspherical SOAs. In the current effort, artificial sand and oil agglomerates (aSOAs) created with the size, density, and shape characteristics of SOAs were studied in a small-oscillatory flow tunnel. These experiments expanded the available data on SOA motion and interaction with the sea floor and were used to examine the applicability of shear-stress formulations to predict SOA mobility. Data collected during these two sets of experiments, including photographs, video, and flow velocity, are presented in this report, along with an analysis of shear-stress-based formulations for incipient motion. The results showed that shear-stress thresholds for typical quartz sand predicted the incipient motion of aSOAs with 0.5–1.0-cm diameters, but were inaccurate for aSOAs with larger diameters (>2.5 cm). This finding implies that modified parameterizations of incipient motion may be necessary under certain combinations of aSOA characteristics and environmental conditions.

Influence of the void ratio and the confining on the static liquefaction in slopes in shangi sand

Directory of Open Access Journals (Sweden)

Alfonso Mariano Ramos Cañón

2015-01-01

Full Text Available A numerical study on the onset of static liquefaction in slopes under undrained conditions of loading was developed based on a general liquefaction flow instability criterion for elastoplastic soils based on the concept of loss of controllability. The criterion is applied to the case of axisymmetric loading to detect the onset of static liquefaction. The criterion is used in conjunction with an elastoplastic model for sands and is tested by means of numerical simulations of element tests. The numerical results are compared with experimental evidence obtaining good agreement. A quantitative study of the influence of the mean pressure, void ratio and the anisotropy of stress on the onset of static liquefaction is presented for the Changi sand. From the analysis of the numerical results, it can be concluded that: a. the mobilized friction angle at the onset of liquefaction is not an intrinsic property of the material, but is a state variable b. Despite of the multiple variables involved in the process of generation of undrained instability, the state of stresses at the onset of static liquefaction can be conveniently represented by a linear relation between Dq/po and no . This graphical representation can be used in the practice of geotechnical engineering to quantify the margin of security against the static liquefaction of a sandy slope.

A combined CFD-experimental method for developing an erosion equation for both gas-sand and liquid-sand flows

Science.gov (United States)

Mansouri, Amir

The surface degradation of equipment due to consecutive impacts of abrasive particles carried by fluid flow is called solid particle erosion. Solid particle erosion occurs in many industries including oil and gas. In order to prevent abrupt failures and costly repairs, it is essential to predict the erosion rate and identify the locations of the equipment that are mostly at risk. Computational Fluid Dynamics (CFD) is a powerful tool for predicting the erosion rate. Erosion prediction using CFD analysis includes three steps: (1) obtaining flow solution, (2) particle tracking and calculating the particle impact speed and angle, and (3) relating the particle impact information to mass loss of material through an erosion equation. Erosion equations are commonly generated using dry impingement jet tests (sand-air), since the particle impact speed and angle are assumed not to deviate from conditions in the jet. However, in slurry flows, a wide range of particle impact speeds and angles are produced in a single slurry jet test with liquid and sand particles. In this study, a novel and combined CFD/experimental method for developing an erosion equation in slurry flows is presented. In this method, a CFD analysis is used to characterize the particle impact speed, angle, and impact rate at specific locations on the test sample. Then, the particle impact data are related to the measured erosion depth to achieve an erosion equation from submerged testing. Traditionally, it was assumed that the erosion equation developed based on gas testing can be used for both gas-sand and liquid-sand flows. The erosion equations developed in this work were implemented in a CFD code, and CFD predictions were validated for various test conditions. It was shown that the erosion equation developed based on slurry tests can significantly improve the local thickness loss prediction in slurry flows. Finally, a generalized erosion equation is proposed which can be used to predict the erosion rate in

Big picture thinking in oil sands tailings disposal

Energy Technology Data Exchange (ETDEWEB)

Boswell, J. [Thurber Engineering Ltd., Calgary, AB (Canada)

2010-07-01

This PowerPoint presentation discussed methods of disposing oil sands tailings. Oil sands operators are currently challenged by a variety of legislative and environmental factors concerning the creation and disposal of oil sands tailings. The media has focused on the negative ecological impact of oil sands production, and technical issues are reducing the effect of some mitigation processes. Operators must learn to manage the interface between tailings production and removal, the environment, and public opinion. The successful management of oil sand tailings will include procedures designed to improve reclamation processes, understand environmental laws and regulations, and ensure that the cumulative impacts of tailings are mitigated. Geotechnical investigations, engineering designs and various auditing procedures can be used to develop tailings management plans. Environmental screening and impact assessments can be used to develop sustainable solutions. Public participation and environmental mediation is needed to integrate the public, environmental and technical tailings management strategies. Operators must ensure public accountability for all stakeholders. tabs., figs.

Hydraulic characterisation of iron-oxide-coated sand and gravel based on nuclear magnetic resonance relaxation mode analyses

Directory of Open Access Journals (Sweden)

S. Costabel

2018-03-01

Full Text Available The capability of nuclear magnetic resonance (NMR relaxometry to characterise hydraulic properties of iron-oxide-coated sand and gravel was evaluated in a laboratory study. Past studies have shown that the presence of paramagnetic iron oxides and large pores in coarse sand and gravel disturbs the otherwise linear relationship between relaxation time and pore size. Consequently, the commonly applied empirical approaches fail when deriving hydraulic quantities from NMR parameters. Recent research demonstrates that higher relaxation modes must be taken into account to relate the size of a large pore to its NMR relaxation behaviour in the presence of significant paramagnetic impurities at its pore wall. We performed NMR relaxation experiments with water-saturated natural and reworked sands and gravels, coated with natural and synthetic ferric oxides (goethite, ferrihydrite, and show that the impact of the higher relaxation modes increases significantly with increasing iron content. Since the investigated materials exhibit narrow pore size distributions, and can thus be described by a virtual bundle of capillaries with identical apparent pore radius, recently presented inversion approaches allow for estimation of a unique solution yielding the apparent capillary radius from the NMR data. We found the NMR-based apparent radii to correspond well to the effective hydraulic radii estimated from the grain size distributions of the samples for the entire range of observed iron contents. Consequently, they can be used to estimate the hydraulic conductivity using the well-known Kozeny–Carman equation without any calibration that is otherwise necessary when predicting hydraulic conductivities from NMR data. Our future research will focus on the development of relaxation time models that consider pore size distributions. Furthermore, we plan to establish a measurement system based on borehole NMR for localising iron clogging and controlling its remediation

Plantar pressure distribution of ostrich during locomotion on loose sand and solid ground

Directory of Open Access Journals (Sweden)

Rui Zhang

2017-07-01

Full Text Available Background The ostrich is a cursorial bird with extraordinary speed and endurance, especially in the desert, and thus is an ideal large-scale animal model for mechanic study of locomotion on granular substrate. Methods The plantar pressure distributions of ostriches walking/running on loose sand/solid ground were recorded using a dynamic pressure plate. Results The center of pressure (COP on loose sand mostly originated from the middle of the 3rd toe, which differed from the J-shaped COP trajectory on solid ground. At mid-stance, a high-pressure region was observed in the middle of the 3rd toe on loose sand, but three high-pressure regions were found on solid ground. The gait mode significantly affected the peak pressures of the 3rd and 4th toes (p = 1.5 × 10−6 and 2.39 × 10−8, respectively, but not that of the claw (p = 0.041. The effects of substrate were similar to those of the gait mode. Discussion Ground reaction force trials of each functional part showed the 3rd toe bore more body loads and the 4th toe undertook less loads. The pressure distributions suggest balance maintenance on loose sand was provided by the 3rd and 4th toes and the angle between their length axes. On loose sand, the middle of the 3rd toe was the first to touch the sand with a smaller attack angle to maximize the ground reaction force, but on solid ground, the lateral part was the first to touch the ground to minimize the transient loading. At push-off, the ostrich used solidification properties of granular sand under the compression of the 3rd toe to generate sufficient traction.

Least tern and piping plover nesting at sand pits in Nebraska

Science.gov (United States)

Sidle, John G.; Kirsch, E.M.

1993-01-01

Endangered Least Terns (Sterna antillarum) and threatened Piping Plovers (Charadrius melodus) nest at commercial sand and gravel mining operations (sand pits) along the Platte River system in Nebraska. Sandbar habitat has been disappearing since the early 1900's along the Platte River system, but numbers of sand pits have increased. We hypothesized that birds would more fully utilize sand pits where suitable sandbar habitat was limited. We inventoried sand pits and censused terns and plovers on both habitats along the Loup River, part of the North Loup River, and most of the Platte River during 1988-1991. Using aircraft, we also quantified features of suitable sand pits present on the central Platte in 1988 and lower Platte in 1990, and related features to abundance and presence of birds. We found 225 sand pits of which 78 were suitable and 187 were unsuitable for nesting. Along the central Platte, where sandbar habitat is severely degraded, birds nested at 81% of the suitable sand pits (N = 32) at least once during 1988-1991, and most birds (61-94%) nested on sand pits. Along the lower Platte, where both sandbar and sand pit habitat are plentiful, birds nested at 60% of the suitable sand pits (N = 35) at least once during 1988-1991, and most birds (60-86%) nested on sandbars. Numbers of terns and plovers were more weakly correlated with features of sand pits on the central Platte than on the lower Platte. Least Terns and Piping Plovers seem to use more of the suitable sand pit habitat on the central Platte than on the lower Platte. Sand pits probably have influenced the birds' distribution by providing alternative nesting habitat along rivers where suitable sandbars are rare or absent.

Characterization of sand lenses embedded in tills

DEFF Research Database (Denmark)

Kessler, Timo Christian; Klint, K.E.S.; Nilsson, B.

2012-01-01

Tills dominate large parts of the superficial sediments on the Northern hemisphere. These glacial diamictons are extremely heterogeneous and riddled with fractures and lenses of sand or gravel. The frequency and geometry of sand lenses within tills are strongly linked to glaciodynamic processes...

Sand impaction of the small intestine in eight dogs.

Science.gov (United States)

Moles, A D; McGhite, A; Schaaf, O R; Read, R

2010-01-01

To describe signalment, clinical findings, imaging and treatment of intestinal sand impaction in the dog. Medical records of dogs with radiographic evidence of small intestinal sand impaction were reviewed. Sand impaction resulting in small intestinal obstruction was diagnosed in eight dogs. All dogs presented with signs of vomiting. Other clinical signs included anorexia, lethargy and abdominal pain. Radiographs confirmed the presence of radio-opaque material consistent with sand causing distension of the terminal small intestine in all dogs. Four dogs were treated surgically for their impaction and four dogs were managed medically. Seven of the eight dogs survived. Both medical and surgical management of intestinal sand impaction in the dog can be effective and both afford a good prognosis for recovery.

Reuse of waste foundry sand through interaction with sodium silicate binder

International Nuclear Information System (INIS)

Souza, J.C.; Chinelatto, A.S.A.; Chinelatto, A.L.; Oliveira, I.L.

2012-01-01

Green sand molds are used in metal casting process. However, after heating, activated bentonite present in green sand lose the binding properties, and part of the foundry sand has to be discarded from the process. The ABNT NBR 15.984/2011 establishes the management of waste foundry sand (WFS) avoiding disposal in landfills. The objective of this work was to investigate the possibility of reusing the WFS from the study of their interaction with sodium silicate binder. Studies with silica sand and new green sand was performed to compare the results obtained with the WFS. The characterizations of the samples were performed by measures the compressive strength, X-ray diffraction, optical microscopy and scanning electron microscopy. The results showed that there is interaction of the sodium silicate with the WFS as well as with the silica sand and green sand. (author)

Geotechnical properties of crude oil contaminated sand

International Nuclear Information System (INIS)

Puri, V.K.; Das, B.M.; Cook, E.E.; Shin, E.C.

1994-01-01

Contamination of soil due to an oil spill influences its subsequent engineering behavior. An investigation was conducted to study the effect of crude oil contamination on compaction characteristics, shear strength, one-dimensional compression, and coefficient of permeability. Water permeability was also determined by using commercial grade motor oils as contaminants. The test results indicate that the compaction characteristics are influenced by oil contamination. The angle of internal friction of sand (based on total stress condition) decreases due to presence of oil within the pore spaces in sand. One dimensional compression characteristics of sand are significantly influenced by oil contamination resulting in a decrease in the value of constrained modulus with increase in the degree of oil contamination compared to the case of dry sand. Water permeability was observed to be a function of the initial viscosity and the degree of saturation due to the contaminating oil

Wear and microstructural characteristics of spray atomized zircon sand reinforced LM13 alloy

Energy Technology Data Exchange (ETDEWEB)

Kaur, K.; Pandey, O.P. [School of Physics and Materials Science, Thapar University Patiala, Punjab (India)

2010-07-15

The requirement of the high performance light weight materials demands the development of varieties of materials within the economical range to get it commercialized. Light weight aluminium alloys are used in several structural applications like automotive, aerospace, defense industry and other fields of engineering. The ceramic particle reinforced aluminium metal matrix composites (AMCs) have emerged as a suitable candidate for commercial applications. A variety of processing routes have been adopted to manufacture AMCs. In the present work LM13 alloy reinforced with zircon sand is formed via spray forming. During experimentation a self prepared convergent-divergent nozzle is used for inert gas atomization of the melt which is subsequently deposited on copper substrate placed vertically below the atomizer. The zircon sand particles are injected in the atomization zone by external injectors aligned perpendicular to the gas atomization axis. Zircon sand has been found to have new promising economical commercial candidate due to its easy availability and good mechanical properties like high hardness, high modulus of elasticity and good thermal stability. The microhardness of cast alloy and spray formed composite shows that the spray formed zircon sand reinforced composite has higher hardness. Also the lower wear rate has been observed in case of the zircon sand reinforced AMC as compared to LM13 alloy. This behaviour is further analyzed in light of microstructural features of the spray deposited composite using optical and scanning electron microscope (SEM). A comparative study of this material (LM13/Zircon sand) with the parent alloy (LM13) is presented in this work. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Production of Steel Casts in Two-Layer Moulds with Alkaline Binders Part 1. Backing sand with the alkaline inorganic binder RUDAL

Directory of Open Access Journals (Sweden)

M. Holtzer

2011-04-01

Full Text Available Steel casts in Z.N. POMET were produced in moulds made of the moulding sand Floster. This sand did not have good knocking outproperties, required a significant binder addition (4.5-5.0 parts by weight, and the casting surface quality gave rise to clients objections.Therefore a decision of implementing two-layer moulds, in which the facing sand would consist of the moulding sand with an alkalineorganic binder while the backing sand would be made of the moulding sand with an inorganic binder also of an alkaline character - wasundertaken. The fraction of this last binder in the moulding sand mass would be smaller than that of the binder used up to now (waterglass. The application of two moulding sands of the same chemical character (highly alkaline should facilitate the reclamation processand improve the obtained reclaimed material quality, due to which it would be possible to increase the reclaim fraction in the mouldingsand (up to now it was 50%. The results of the laboratory investigations of sands with the RUDAL binder are presented in the paper.

Sanding dust from nanoparticle-containing paints: Physical characterisation

International Nuclear Information System (INIS)

Koponen, I K; Jensen, K A; Schneider, T

2009-01-01

Increasing use of nanoparticles in different industrial applications has raised a new potential health risk to the workers as well as to the consumers. This study investigates the particle size distributions of sanding dust released from paints produced with and without engineered nanoparticles. Dust emissions from sanding painted plates were found to consist of five size modes; three modes under 1 μm and two modes around 1 and 2 μm. We observed that the sander was the only source of particles smaller than 50 nm and they dominated the number concentration spectra. Mass and surface area spectra were dominated by the 1 and 2 μm modes. Addition of nanoparticles caused only minor changes in the geometric mean diameters of the particle modes generated during sanding of two paints doped with 17 nm TiO2 and 95 nm Carbon Black nanoparticles as compared to the size modes generated during sanding a conventional reference paint. However, the number concentrations in the different size modes varied considerably in between the two NP-doped paints and the reference paint. Therefore, from a physical point of view, there may be a difference in the exposure risk during sanding surfaces covered with nanoparticle-based paints as compared to sanding conventional paints.

Laboratory assessment of the influence of the proportion of waste foundry sand on the geotechnical engineering properties of clayey soils

CSIR Research Space (South Africa)

Mgangira, Martin B

2006-01-01

Full Text Available Soil improvement can be achieved through mechanical stabilisation using industrial byproducts. Clayey soils were blended with waste foundry sand to examine its influence on the geotechnical engineering properties of the soils. The waste foundry sand...

SANDS: a service-oriented architecture for clinical decision support in a National Health Information Network.

Science.gov (United States)

Wright, Adam; Sittig, Dean F

2008-12-01

In this paper, we describe and evaluate a new distributed architecture for clinical decision support called SANDS (Service-oriented Architecture for NHIN Decision Support), which leverages current health information exchange efforts and is based on the principles of a service-oriented architecture. The architecture allows disparate clinical information systems and clinical decision support systems to be seamlessly integrated over a network according to a set of interfaces and protocols described in this paper. The architecture described is fully defined and developed, and six use cases have been developed and tested using a prototype electronic health record which links to one of the existing prototype National Health Information Networks (NHIN): drug interaction checking, syndromic surveillance, diagnostic decision support, inappropriate prescribing in older adults, information at the point of care and a simple personal health record. Some of these use cases utilize existing decision support systems, which are either commercially or freely available at present, and developed outside of the SANDS project, while other use cases are based on decision support systems developed specifically for the project. Open source code for many of these components is available, and an open source reference parser is also available for comparison and testing of other clinical information systems and clinical decision support systems that wish to implement the SANDS architecture. The SANDS architecture for decision support has several significant advantages over other architectures for clinical decision support. The most salient of these are:

[Preliminary Study of Lonicera hypoglauca on Germination Conditions of Sand Culture Seeds and Sterilization Method of Sand Culture Seedling Sterilization].

Science.gov (United States)

Tan, Mu-xiu; Zeng, Wen-wen; Wei, Peng-xiao; Mo, Qiao-cheng; Pu, Zu-ning; Cen, Xiu-fen; Shi, Feng-hua

2015-05-01

To explore the germination conditions of Lonicera hypoglauca sand culture seeds and the effects of sand culture seedlings sterilization. 0.1% HgCl2 with different sterilization time, different illumination time and temperature culture condition were adopted to study the germination conditions of sand culture seeds. Different sterilization treatments and different hardening-seedling days were used to test the sterilization effect of sand culture seedlings. The sterilization effect of the combination of 75% ethanol 30 s + 0.1% HgCl2 5 min on Lonicera hypoglauca seeds was the optimum,with the average pollution rate of 15.56%, and the average germination rate reached 51.11%. The combination of varied temperature-room temperature under light for 12 h/d was the best, with the average germination rate peaked at 75.49%, and the average germination potential reached 68.36%. The treatment of detergent liquor scrub-tap water wash on the part above the hypocotyl, which was sand cultured under the opening condition and had no root, showed the best sterilization effect, with the average pollution rate was zero, and the average survival rate peaked at 100.00%. The sterilization effect of sand culture seedlings, which was disinfected after cleaning by detergent liquor scrub-tap water wash after hardening-seeding for 30 days, was the best, with the average pollution rate of 50.00%, and the average survival rate of 100.00%. The best sterilization effect is the combination of 75% ethanol 30 s + 0.1% HgCl2 5 min; Lighting for 12 h/d of varied temperature-room temperature is regarded as the optimum culture condition. The treatment of detergent liquor scrub-tap water wash treatment on the part above the hypocotyl,which is sand cultured under the opening condition and had no root, shows the best sterilization effect. For the sand culture seedlings, before inoculated in subculture medium, should be hardening-seedling for some days and sterilized after detergent liquor scrub-tap water wash.

Effectiveness of Sand-Therapy on the Attenuation of Separation anxiety Signs in Pre-School Children

Directory of Open Access Journals (Sweden)

Arghavan Shariat

2015-01-01

Full Text Available Background and Objective: The present research was conducted with the aim of determining effect of Sand-therapy on the attenuation of separation anxiety signs among pre-school children in Isfahan, Iran. Methods: The statistical society consists of all pre-school children who had separation anxiety disorder and Among100 children, 30 persons were selected using available sampling. The method of this research is quasi-experimental with one group and pre-test and post-test plan. After performing pre-test of separation anxiety disorder scale, the experimental group were trained under sand-therapy training in 10 sessions of 60 minutes for a period of two months and after that, post-test of separation anxiety disorder scale was performed. The research tool consists of the questionnaire CSI-4 of child’s morbid signs. Wilcoxon method was used to analysis the results. Results: The research findings showed that there was a meaningful different (P=0.008 between pre- test & post-test scores of anxiety signs for study group.Conclusion: As a practical message, we can mention that sand therapy is as an interesting and practical playing for the children and it is a meaningful therapy related to attenuation of separation anxious signs. Keywords: Sand therapy, separation anxiety, pre-school-children

Strength and Compaction Analysis of Sand-Bentonite-Coal Ash Mixes

Science.gov (United States)

Sobti, Jaskiran; Singh, Sanjay Kumar

2017-08-01

This paper deals with the strength and compaction characteristics of sand-bentonite-coal ash mixes prepared by varying percentages of sand, bentonite and coal ash to be used in cutoff walls and as a liner or cover material in landfills. The maximum dry density (MDD) and optimum moisture content (OMC) of sand-bentonite mixes and sand-bentonite-coal ash mixes were determined by conducting the standard proctor test. Also, the strength and stiffness characteristics of soil mixes were furnished using unconfined compressive strength test. The results of the study reveal influence of varying percentages of coal ash and bentonite on the compaction characteristics of the sand-bentonite-coal ash mixes. Also, validation of a statistical analysis of the correlations between maximum dry density (MDD), optimum moisture content (OMC) and Specific Gravity (G) was done using the experimental results. The experimental results obtained for sand-bentonite, sand-bentonite-ash and coal ash-bentonite mixes very well satisfied the statistical relations between MDD, OMC and G with a maximum error in the estimate of MDD being within ±1 kN/m3. The coefficient of determination (R2) ranged from 0.95 to 0.967 in case of sand-bentonite-ash mixes. However, for sand-bentonite mixes, the R2 values are low and varied from 0.48 to 0.56.

Influence of the reclamation method of spent moulding sands on the possibility of creating favourable conditions for gases flow in a mould

Directory of Open Access Journals (Sweden)

Łucarz M.

2017-03-01

Full Text Available The results of investigations concerning the influence of the applied sand matrix (fresh sand, reclaim on the properties of moulding sands used for production of large dimensional castings (ingot moulds, ladles, are presented in the hereby paper. The performed investigations were aimed at determining the influence of various reclamation methods of spent moulding sands on the quality of the obtained reclaimed material. Moulding sands were prepared on the fresh quartz matrix as well as on sand matrices obtained after various reclamation methods. The selected moulding sand parameters were tested (strength, permeability, grindability, ignition losses, pH reactions. It can be stated, on the basis of the performed investigations, that the kind of the applied moulding sand matrix is of an essential meaning from the point of view of creating conditions minimising formation of large amounts of gases and their directional migration in a casting mould.

Sand filter clogging by septic tank effluent.

Science.gov (United States)

Spychała, M; Błazejewski, R

2003-01-01

The aim of this study was to characterise conditions and factors affecting fine sand clogging by septic tank effluent on the basis of physical modelling. The physical model consisted of 12 sand columns dosed with sewage from one household (5 persons), preliminary treated in a septic tank. Hydraulic loadings of the sand filters were equal to 82 mm/d. The mean discharge from sand columns, measured as the effluent volume collected during 10 minutes, decreased significantly over the experiment period from 34 cm3/min in August 2000 to 20 cm3/min in August 2001 at the same temperature of about 20 degrees C. First the columns clogged almost completely after 480 days in December 2001, however six columns had remained unclogged till the end of the experiment (March 2002). The temperature had a significant impact on hydraulic conductivity. A vertical distribution of accumulated mass and biomass was investigated in partly clogged sand. Microscopic survey of the clogging layer showed a presence of live micro-organisms, residuals of dead micro-organisms, particularly pieces of small animal armour and many fibres. These particles accelerated the accumulation of solids in the upper clogging layer. The study indicated that temperature impact on the filter hydraulic conductivity was more significant for biological activity, than for sewage viscosity.

Gravel Mobility in a High Sand Content Riverbed

Science.gov (United States)

Haschenburger, J. K.

2017-12-01

In sand-gravel channels, sand may modify gravel transport by changing conditions of entrainment and promoting longer displacements or gravel may inhibit sand transport if concentrated into distinct deposits, which restrict sand supply with consequences for migrating bedform size or form. This study reports on gravel mobility in the lower San Antonio River, Texas, where gravel content in the bed material ranges from about 1% to more than 20%. Sediment transport observations were collected at three U.S. Geological Survey gauging stations by deploying a Helley-Smith sampler with a 0.2 mm mesh bag from which transport rates and mobile grain sizes were determined. The flow rates sampled translate into an annual exceedance expectation from 0.2% to 98%. Gravel transport rates are generally two orders of magnitude smaller than the rates of sand transport. However, the finest gravels are transported at rates on the same order of magnitude as the coarsest sands. At all sites, the 2 and 2.8 mm fractions are transported at the lowest flow rate sampled, suggesting mobility for at least 38% to as much as 98% of the year. Fractions as large as 8 mm are mobilized at flow rates that are expected between 25% and 53% of the year. The largest fractions captured in the sampling (16 to 32 mm) require flows closer to bankfull conditions that occur no more than 0.8% of the year. Results document that some gravel sizes can be frequently transported in low gradient riverbeds with high sand content.

Study of Dronino Iron Meteorite Weathering in Clay Sand Using Mössbauer Spectroscopy

Directory of Open Access Journals (Sweden)

Grigoriy A. Yakovlev

2016-06-01

Full Text Available Weathering products of two fragments of Dronino iron ungrouped meteorite found in the wet and drier clay sand were studied using X-ray diffraction and Mössbauer spectroscopy with a high velocity resolution. The products of metal oxidation in the internal and external surface layers were different for both fragments. The weathering products in fragment found in the wet clay sand contain magnetite (Fe3O4, maghemite (γ-Fe2O3, goethite (α-FeOOH and probably ferrihydrite (5Fe2O3∙9H2O while those in fragment found in drier clay sand contained ferric hydrous oxides (FeOOH and siderite (FeCO3 mainly. Concretions found near the first fragment contain ferric hydrous oxides (FeOOH mainly. This work is licensed under a Creative Commons Attribution 4.0 International License.

Sugarcane Yield Response to Furrow-Applied Organic Amendments on Sand Soils

Directory of Open Access Journals (Sweden)

J. Mabry McCray

2015-01-01

Full Text Available Organic amendments have been shown to increase sugarcane yield on sand soils in Florida. These soils have very low water and nutrient-holding capacities because of the low content of organic matter, silt, and clay. Because of high costs associated with broadcast application, this field study was conducted to determine sugarcane yield response to furrow application of two organic amendments on sand soils. One experiment compared broadcast application (226 m3 ha−1 of mill mud and yard waste compost, furrow application (14, 28, and 56 m3 ha−1 of these materials, and no amendment. Another experiment compared furrow applications (28 and 56 m3 ha−1 of mill mud and yard waste compost with no amendment. There were significant yield (t sucrose ha−1 responses to broadcast and furrow-applied mill mud but responses to furrow applications were not consistent across sites. There were no significant yield responses to yard waste compost suggesting that higher rates or repeated applications of this amendment will be required to achieve results comparable to mill mud. Results also suggest that enhancing water and nutrient availability in the entire volume of the root zone with broadcast incorporation of organic amendments is the more effective approach for low organic matter sands.

Scour at Vertical Piles in Sand-Clay Mixtures under Waves

DEFF Research Database (Denmark)

Dey, Subhasish; Helkjær, Anders; Sumer, B. Mutlu

2011-01-01

Marine sediments often contain sand-clay mixtures in widely varying proportions. This study presents the results of equilibrium scour and time variation of scour depths at circular piles embedded vertically in clay alone and sand-clay mixed beds under waves. Experiments were conducted in a wave...... flume with different proportions of sand-clay mixtures as bed sediments. Test results for the cases of steady current and sand alone under waves are used as references. The equilibrium scour depth reduces with an increase in clay proportion n (by weight) in a sand-clay mixture. Interestingly, the scour...

Frac sand in the United States: a geological and industry overview

Science.gov (United States)

Benson, Mary Ellen; Wilson, Anna B.; Bleiwas, Donald I.

2015-01-01

A new mineral rush is underway in the upper Midwest of the United States, especially in Wisconsin and Minnesota, for deposits of high-quality frac sand that the mining industry calls “Northern White” sand or “Ottawa” sand. Frac sand is a specialized type of sand that is added to fracking fluids that are injected into unconventional oil and gas wells during hydraulic fracturing (fracking or hydrofracking), a process that enhances petroleum extraction from tight (low permeability) reservoirs. Frac sand consists of natural sand grains with strict mineralogical and textural specifications that act as a proppant (keeping induced fractures open), extending the time of release and the flow rate of hydrocarbons from fractured rock surfaces in contact with the wellbore.

Study on GMZ bentonite-sand mixture by undrained triaxial tests

Directory of Open Access Journals (Sweden)

Sun Wen-jing

2016-01-01

Full Text Available It is particularly necessary to study the deformation, strength and the changes of pore water pressure of bentonite-based buffer/backfill materials under the undrained condition. A series of isotropic compression tests and triaxial shear tests under undrained conditions were conducted on the compacted saturated/unsaturated GMZ bentonite-sand mixtures with dry mass ratio of bentonite/sand of 30:70. During the tests, the images of the sample were collected by photographic equipment and subsequently were cropped, binarized and centroids marked by image processing technique. Based on identification of the variation of the position of marked centroids, the deformation of the sample can be determined automatically in real-time. Finally, the hydro-mechanical behaviour of saturated and unsaturated bentonite-sand mixtures under the undrained condition can be obtained. From results of triaxial shear tests on unsaturated samples under constant water content, inflated volumetric deformation transforms to contractive volumetric deformation due to the increase of the confining pressure and lateral expansion deformation are observed due to the increase in the shearing stress. Moreover, the net mean stress affects the initial stiffness, undrained shear strength and deformation of the sample during the undrained shear tests.

On shelterbelt design for combating sand invasion.

NARCIS (Netherlands)

Mohammed, A.E.; Stigter, C.J.; Adam, H.S.

1996-01-01

After a review of the scarce literature on using trees against sand encroachment, a quantitative experiment with a wide shelterbelt to combat sand invasion is reported on. Experimental work was carried out at the northwestern border of the Gezira Scheme (Sudan), an area of severe land degradation

Short Communications Sand moisture as a factor determining depth ...

African Journals Online (AJOL)

1993-11-05

Nov 5, 1993 ... The depths to which the animals burrow are, at least partly. determined by the moisture gradient in the sand. They are, however, incapable of burrowing into totally dry sand. Animals alter their position in the sand in response to changes in moisture content so as to ensure exposure to suitable conditions.

Assessment of source material (U and Th) in exploration, mining, processing of zircon sand in Central Kalimantan

International Nuclear Information System (INIS)

Dedi Hermawan; Pandu Dewanto; Sudarto

2011-01-01

From 2004 to 2008, according to data released by the Commerce Department, the volume of zircon sand and concentrates exports has increased highly. One of many locations in Indonesia that widely available zircon sand is Kalimantan island. For example, Central Kalimantan Province in 2007 to 2008 exports about 51,000 tones up to 79,000 tones of zircon sand annually. The concentration of source material in the zircon sand is important to be known because the presence of natural radioactive U and Th in zircon sand has the potential radiation hazard. Therefore it is necessary to conduct an assessment the potential reserves related to the source material contained in the zircon sand and radiation safety that are applied in the process of mining or processing of zircon sand. In this paper the location of mining and processing of zircon sand is restricted to the province of Central Kalimantan. From the assessment obtained that source material which is carried by zircon sand export form the province of Central Kalimantan have the potential to exceed the limits set by the BAPETEN Chairman Decree No.9 of 2006 About the Implementation of the Additional Protocol to the Accountability System and Control of Nuclear Materials. In terms of compliance with radiation safety, required increased surveillance of K3 during mining, process / processing by the worker, supervisor / supervisors and regional management company to be able the achievement of compliance with the provisions of the management of materials and the safety of radiation sources based on national regulations (BAPETEN) and international. (author)

The extraction of bitumen from western oil sands

International Nuclear Information System (INIS)

Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1992-08-01

The University of Utah tar sand research and development program is concerned with research and development on Utah is extensive oil sands deposits. The program has been intended to develop a scientific and technological base required for eventual commercial recovery of the heavy oils from oil sands and processing these oils to produce synthetic crude oil and other products such as asphalt. The overall program is based on mining the oil sand, processing the mined sand to recover the heavy oils and upgrading them to products. Multiple deposits are being investigated since it is believed that a large scale (approximately 20,000 bbl/day) plant would require the use of resources from more than one deposit. The tasks or projects in the program are organized according to the following classification: Recovery technologies which includes thermal recovery methods, water extraction methods, and solvent extraction methods; upgrading and processing technologies which covers hydrotreating, hydrocracking, and hydropyrolysis; solvent extraction; production of specialty products; and environmental aspects of the production and processing technologies. These tasks are covered in this report

Effect of water content on the water repellency for hydrophobized sands

Science.gov (United States)

Subedi, S.; Kawamoto, K.; Kuroda, T.; Moldrup, P.; Komatsu, T.

2011-12-01

Alternative earthen covers such as capillary barriers (CBs) and evapotranspirative covers are recognized as useful technical and low-cost solutions for limiting water infiltration and controlling seepage flow at solid waste landfills in semi-arid and arid regions. However, their application to the landfills at wet regions seems to be matter of concern due to loss of their impending capability under high precipitation. One of the possible techniques to enhance the impermeable properties of CBs is to alter soil grain surfaces to be water-repellent by mixing/coating hydrophobic agents (HAs). In order to examine a potential use of model sands hydrophobized with locally available and environmental-friendly HAs such as oleic acid (OA) and stearic acid (SA) for hydrophobic CBs. In the present study, we first characterized the effect of water content on the degree of water repellency (WR) for hydrophobized sands and volcanic ash soil at different depth. Secondly, the time dependency of the contact angle in hydrophobized sands and volcanic ash soils at different water content was evaluated. Further, the effects of hydrophobic organic matter contents on the WR of hydrophobized sands were investigated by horizontal infiltration test. We investigated the degree of WR as functions of volumetric water content (θ) of a volcanic ash soil samples from different depth and water adjusted hydrophobized sand samples with different ratio of HAs by using sessile drop method (SDM). The initial contact angle (αi) measured from SDM decreased gradually with increasing water content in OA and SA coated samples. Measured αi values for volcanic ash soils increased with increasing water content and reached a peak values of 111.7o at θ= 0.325 cm3 cm-3, where-after αi gradually decreased. Each test sample exhibited sharp decrease in contact angle with time at higher water content. Sorptivity values for oleic acid coated samples decreased with increasing HA content and reached the minimum

Application of Self Cleaning Rapid Sand Filter in Water Treatment

Directory of Open Access Journals (Sweden)

Ali Reza Rahmani

2005-08-01

Full Text Available Rapid sand filter is one of the most important units in the water treatment plants. It has some difficulties in operation such as backwashing. For the solving of this problem a rapid sand filter has designed and built with the self-cleaning backwashing system. This system consist of 3 main constituents; one galvanized siphon and two galvanized steel tanks. One of them is used for filtration and the other used for the storage of filtrated water in elevation for backwashing the system. Water enter from upside of the filter through the inlet pipe, and collected from the under drainage pipe. Then filter water conduct to the storage tank and exit from outlet pipe. In the beginning, the head loss was low, but because of bed clogging by suspended solids, it increases gradually to the designed head loss (1.2m. Then the system is outed of the service automatically and the backwash is began. The main data for the design of system selected from the hydraulic rules of siphons and rapid sand filter criteria. After essential calculations it was constructed and was started operation. For the hydraulic studies a known volume of storage tank was selected and the time needed for the fill (in filtration stage and empty (in backwash stage of water volume with volumetric method were measured. In hydraulic studies the filter surface rate (SOR was selected about 5-7.5m3/m2/hr (1.39-2.08 lit/sec and the flow of water in siphon, during the backwashing was measured 8.7 lit/sec. It can be seen that the siphon passes 4-6 times the inlet raw water thus a negative pressure will created in the siphon which causes the water above the sand bed to be discharged automatically and rinse water from elevated tank flow under the sand bed and back wash it. So according to this study self cleaning rapid sand filter is very useful for water filtration, especially in small population community. The construction of system is rapid, simple and economic.

Sand ridge morphology and bedform migration patterns derived from bathymetry and backscatter on the inner-continental shelf offshore of Assateague Island, USA

Science.gov (United States)

Pendleton, Elizabeth; Brothers, Laura; Thieler, E. Robert; Sweeney, Edward

2017-01-01

The U.S. Geological Survey and the National Oceanographic and Atmospheric Administration conducted geophysical and hydrographic surveys, respectively, along the inner-continental shelf of Fenwick and Assateague Islands, Maryland and Virginia over the last 40 years. High resolution bathymetry and backscatter data derived from surveys over the last decade are used to describe the morphology and presence of sand ridges on the inner-continental shelf and measure the change in the position of smaller-scale (10–100 s of meters) seafloor features. Bathymetric surveys from the last 30 years link decadal-scale sand ridge migration patterns to the high-resolution measurements of smaller-scale bedform features. Sand ridge morphology on the inner-shelf changes across-shore and alongshore. Areas of similar sand ridge morphology are separated alongshore by zones where ridges are less pronounced or completely transected by transverse dunes. Seafloor-change analyses derived from backscatter data over a 4–7 year period show that southerly dune migration increases in magnitude from north to south, and the east-west pattern of bedform migration changes ~ 10 km north of the Maryland-Virginia state line. Sand ridge morphology and occurrence and bedform migration changes may be connected to observed changes in geologic framework including topographic highs, deflated zones, and sand availability. Additionally, changes in sand ridge occurrence and morphology may help explain changes in the long-term shoreline trends along Fenwick and Assateague Islands. Although the data presented here cannot quantitatively link sand ridges to sediment transport and shoreline change, it does present a compelling relationship between inner-shelf sand availability and movement, sand ridge occurrence and morphology, geologic framework, and shoreline behavior.

Methane Hydrate Formation and Dissociation in the Presence of Silica Sand and Bentonite Clay

Directory of Open Access Journals (Sweden)

Kumar Saw V.

2015-11-01

Full Text Available The formation and dissociation of methane hydrates in a porous media containing silica sand of different sizes and bentonite clay were studied in the presence of synthetic seawater with 3.55 wt% salinity. The phase equilibrium of methane hydrate under different experimental conditions was investigated. The effects of the particle size of silica sand as well as a mixture of bentonite clay and silica sand on methane hydrate formation and its dissociation were studied. The kinetics of hydrate formation was studied under different subcooling conditions to observe its effects on the induction time of hydrate formation. The amount of methane gas encapsulated in hydrate was computed using a real gas equation. The Clausius-Clapeyron equation is used to estimate the enthalpy of hydrate dissociation with measured phase equilibrium data.

Criteria for an advanced assessment of quality of moulding sands with organic binders and reclamation process products

Directory of Open Access Journals (Sweden)

R. Dańko

2013-05-01

Full Text Available Reclamation of used moulding and core sands has been defined as a treatment of waste moulding refractory materials, enabling a recovery of at least one of the components having properties similar to those of the fresh component, and reuse for production of casting moulds and cores. However, at present, there is a lack of a reclaimed material assessment index, which could be applied to each type of moulding sand and reclaim. Modern investigation methods and equipment for the estimation of the quality of the moulding sands matrices with organic binders, in their circulation process, are presented in this paper. These methods, utilizing the special equipment combined with the author’s investigation methods developed in the Faculty of Foundry Engineering, AGH - University of Science and Technology, allow the better estimation of the matrix quality both in an aspect of its application as a fresh sand substitute in the preparation of moulding sands, and also with regard to the environmental protection. The most important criteria for the technological assessment of the reclaimed materials and the quality of sands with organic binders are presented in this paper.

Evaluation of sand reserves in del Plata City

International Nuclear Information System (INIS)

Loureiro, J.

2014-01-01

The purpose of this study is to evaluate the reserve of sand in the zone of del Plata city and beyond. This area is located in the S E edge of the department of San Jose near the mouth of Santa Lucia river. In this zone was identified the mantle of potentially exploitable sand which are based on their particle size, composition and depth of the limits cape. There are two powerful capes of sand separated by clay and silt

Seasonal fluctuations of phlebotomines sand fly populations ...

African Journals Online (AJOL)

An entomological survey of phlebotomine sand flies was conducted in the Moulay Yacoub province, central Morocco. An anthropic niche (Ouled Aid) and a wild niche (Zliligh) were selected. Sand flies were collected twice a month between April 2011 and March 2012, using sticky traps and CDC light traps. 3675 specimens ...

Molecular Diversity between Salivary Proteins from New World and Old World Sand Flies with Emphasis on Bichromomyia olmeca, the Sand Fly Vector of Leishmania mexicana in Mesoamerica.

Science.gov (United States)

Abdeladhim, Maha; V Coutinho-Abreu, Iliano; Townsend, Shannon; Pasos-Pinto, Silvia; Sanchez, Laura; Rasouli, Manoochehr; B Guimaraes-Costa, Anderson; Aslan, Hamide; Francischetti, Ivo M B; Oliveira, Fabiano; Becker, Ingeborg; Kamhawi, Shaden; Ribeiro, Jose M C; Jochim, Ryan C; Valenzuela, Jesus G

2016-07-01

Sand fly saliva has been shown to have proteins with potent biological activities, salivary proteins that can be used as biomarkers of vector exposure, and salivary proteins that are candidate vaccines against different forms of leishmaniasis. Sand fly salivary gland transcriptomic approach has contributed significantly to the identification and characterization of many of these salivary proteins from important Leishmania vectors; however, sand fly vectors in some regions of the world are still neglected, as Bichromomyia olmeca (formerly known as Lutzomyia olmeca olmeca), a proven vector of Leishmania mexicana in Mexico and Central America. Despite the importance of this vector in transmitting Leishmania parasite in Mesoamerica there is no information on the repertoire of B. olmeca salivary proteins and their relationship to salivary proteins from other sand fly species. A cDNA library of the salivary glands of wild-caught B. olmeca was constructed, sequenced, and analyzed. We identified transcripts encoding for novel salivary proteins from this sand fly species and performed a comparative analysis between B. olmeca salivary proteins and those from other sand fly species. With this new information we present an updated catalog of the salivary proteins specific to New World sand flies and salivary proteins common to all sand fly species. We also report in this work the anti-Factor Xa activity of Lofaxin, a salivary anticoagulant protein present in this sand fly species. This study provides information on the first transcriptome of a sand fly from Mesoamerica and adds information to the limited repertoire of salivary transcriptomes from the Americas. This comparative analysis also shows a fast degree of evolution in salivary proteins from New World sand flies as compared with Old World sand flies.

Characterizing resilient behavior of naturally occurring bituminous sands for road construction

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2010-11-01

Full Text Available large capacity haul trucks and shovels. This paper focuses on determining in laboratory the resilient behavior of three oil sand materials with bitumen contents of 8.5, 13.3, and 14.5% by weight. The resilient modulus MR properties were obtained using a...

Sand ramps as palaeoenvironmental archives: Integrating general principles and regional contexts through reanalysis of the Klipkraal Sands, South Africa

Science.gov (United States)

Rowell, Alexandra L. K.; Thomas, David S. G.; Bailey, Richard M.; Holmes, Peter J.

2018-06-01

Sand ramps occur on a continuum of topographically-controlled landforms, ranging from purely aeolian features (climbing/falling dunes) to talus cones and alluvial fans. Sand ramps have been identified as potentially important palaeoenvironmental archives in dryland regions that possess relatively few Quaternary proxy records. Their utility however requires not only good age control of depositional phases but clear identification of process regimes, determined through morphological and sedimentological analyses, with several recent studies indicating the complexities of palaeoenvironmental interpretations and the controls of ramp development (Bateman et al., 2012; Rowell et al., 2018). Klipkraal Sands is a sand ramp on the north-eastern margin of the semi-arid Karoo that has been important for inferences of the extent of southern African Late Quaternary aeolian activity (Thomas et al., 2002). We reanalyse this feature, in the light of both its significance and other recent studies that have inferred extensive southern African LGM aeolian activity (Telfer et al., 2012, 2014). New sedimentological data and twelve OSL dates indicate the Klipkraal Sands formed episodically between 100-0.14 ka, rather than accumulating rapidly, while sedimentological data question the aeolian affinities of the bulk of the feature. Therefore, Klipkraal is reinterpreted as showing no particular affinity to the LGM, with sediments locally sourced with a significant colluvial component. Only the upper historical sediments can be clearly interpreted as aeolian deposits. A complex interplay of processes is suggested, for which a meaningful palaeoenvironmental interpretation cannot be easily defined. This implies that the local geomorphic processes and controls operating on sand ramps need to be established before they can be fully utilised as palaeoenvironmental archives, with implications for their interpretation worldwide.

Heavy mineral concentration from oil sand tailings

Energy Technology Data Exchange (ETDEWEB)

Chachula, F.; Erasmus, N. [Titanium Corp. Inc., Regina, SK (Canada)

2008-07-01

This presentation described a unique technique to recover heavy minerals contained in the froth treatment tailings produced by oil sand mining extraction operations in Fort McMurray, Alberta. In an effort to process waste material into valuable products, Titanium Corporation is developing technology to recover heavy minerals, primarily zircon, and a portion of bitumen contained in the final stage of bitumen processing. The process technology is being developed to apply to all mined oil sands operations in the Fort McMurray region. In 2004, Titanium Corporation commissioned a pilot research facility at the Saskatchewan Research Council to test dry oil sands tailings. In 2005, a bulk sampling pilot plant was connected to the fresh oil sands tailings pipeline on-site in Fort McMurray, where washed sands containing heavy minerals were processed at a pilot facility. The mineral content in both deposited tailings and fresh pipeline tailings was assessed. Analysis of fresh tailings on a daily basis identified a constant proportion of zircon and higher levels of associated bitumen compared with the material in the deposited tailings. The process flow sheet design was then modified to remove bitumen from the heavy minerals and concentrate the minerals. A newly modified flotation process was shown to be a viable processing route to recover the heavy minerals from froth treatment tailings. 8 refs., 9 tabs., 12 figs.

Experimental assessment of the liquefaction resistance of calcareous biogenous sands

Directory of Open Access Journals (Sweden)

Sandoval Eimar

2012-10-01

Full Text Available

ABSTRACT

Liquefaction is a phenomenon in which soils, typically sands, suddenly loose a substantial amount of their shear strength and stiffness, this often triggered by large-magnitude earthquakes. Most liquefaction research has focused on silicate-based sands and not on other sand types, such as calcareous biogenous sands Calcareous sands are usually composed of skeletal or non-skeletal remains of marine organisms, with unique characteristics in terms of their mineralogy surface roughness, particle shape, crushability, and intraparticle porosity. The unique characteristics of calcareous sands suggest that their geotechnical engineering behaviour can be substantially different compared to that of terrigenous sands, including their behaviour under seismic loading, which have not been very well studied

This paper presents the results of an experimental programme aimed at studying the cyclic liquefaction resistance of uncemented calcareous biogenous sands retrieved from south-western Puerto Rico Evaluation of liquefaction potential involved a comprehensive set of isotropically consolidated undrained cyclic triaxial tests on reconstituted samples of this calcareous sand. The programme also included tests on Ottawa terrigenous silica sand samples prepared and tested in similar conditions for comparison purposes.

In general, the experimental results showed that Cabo Rojo calcareous sands had higher liquefaction resistance compared to Ottawa silica sands tested under similar conditions. Important differences between calcareous and silica sands regarding pore pressure generation characteristics and axial strain accumulation were also observed

Quality stabilisation of synthetic sand containing bentonite in process lines

OpenAIRE

A. Fedoryszyn

2010-01-01

Stabilisation of sand quality requires the monitoring and control of sand moisture contents and its other parameters at each stage of sandprocessing, i.e. during the preparation of return sand mix and rebonding processes. Stabilisation of sand quality necessitates the use of reliable control equipment and evaluation procedures. This study outlines the scope and results of research work aimed to improve the control equipment to enhance the performance of turbine mixers. The paper reviews the m...

Advanced CANDU reactor: an optimized energy source of oil sands application

International Nuclear Information System (INIS)

Hopwood, J.M.; Bock, D.; Miller, A.; Kuran, S.; Keil, H.; Fiorino, L.; Duffey, R.; Dunbar, R.B.

2003-01-01

Atomic Energy of Canada Limited (AECL) is developing the ACR-700 TM (Advanced CANDU Reactor-700 TM ) to meet customer needs for reduced capital cost, shorter construction schedule, high capacity factor while retaining the benefits of the CANDU experience base. The ACR-700 is based on the concept of CANDU horizontal fuel channels surrounded by heavy water moderator. The major innovation of this design is the use of slightly enriched uranium fuel in a CANFLEX bundle that is cooled by light water. This ensures: higher main steam pressures and temperatures providing higher thermal efficiency; a compact and simpler reactor design with reduced capital costs and shorter construction schedules; and reduced heavy water inventory compared to existing CANDU reactors. ACR-700 is not only a technically advanced and cost effective solution for electricity generating utilities, but also a low-cost, long-life and sustainable steam source for increasing Alberta's Oil Sand production rates. Currently practiced commercial surface mining and extraction of Oil Sand resources has been well established over the last three decades. But a majority of the available resources are somewhat deeper underground require in-situ extraction. Economic removal of such underground resources is now possible through the Steam Assisted Gravity Drainage (SAGD) process developed and proto-type tested in-site. SAGD requires the injection of large quantities of high-pressure steam into horizontal wells to form reduced viscosity bitumen and condensate mixture that is then collected at the surface. This paper describes joint AECL studies with CERI (Canadian Energy Research Institute) for the ACR, supplying both electricity and medium-pressure steam to an oil sands facility. The extensive oil sands deposits in northern Alberta are a very large energy resource. Currently, 30% of Canda's oil production is from the oil sands and this is expected to expand greatly over the coming decade. The bitumen deposits in the

Sand transport, erosion and granular electrification

DEFF Research Database (Denmark)

Merrison, J.P.

2012-01-01

is expanding our current understanding and outline the areas of advancement needed in the future. Presentation is made of current models for wind driven detachment/entrainment and the transport rates of sand and dust, including the effects of contact induced grain electrification. This ubiquitous phenomenon...... can affect grain transport through the generation of intense electric fields and processes of electrostatic assembly. Importantly the transport of sand is characterized by saltation, which is known to be an active process for erosion and therefore a source for dust and sand formation. Using novel...... erosion simulation techniques the link between grain transport rates and erosion rates has been quantified. Furthermore this can be linked to production rates for dust and has been associated with chemical and mineral alteration through a process of mechanical activation of fractured surfaces. This work...

Two-fold sustainability – Adobe with sawdust as partial sand replacement

Science.gov (United States)

Jokhio, Gul A.; Syed Mohsin, Sharifah M.; Gul, Yasmeen

2018-04-01

Adobe is a material that is economic, environment friendly, and provides better indoor air quality. The material required for the preparation of adobe include clay, sand, and sometimes straw or other organic materials. These materials do not require industrial processing or transportation, however, sand mining has been recently posing a threat to the environment. Therefore, to enhance the existing sustainability of adobe, sand can be partially or fully replaced by other waste materials. This approach will not only solve the problem of excessive sand mining, it will also address the issue of waste management. Sawdust is one such waste material that can be used to partially replace sand in Adobe. This paper presents the results of compressive and flexural test carried out on Adobe samples with partial sand replacement by sawdust. The results show that about 4% sand replacement by volume produces higher compressive strength, whereas the flexural strength reduces with the use of sawdust. However, since flexural strength is not a critical property for adobe, it is concluded that replacing sand with sawdust by about 4% of volume will be beneficial.

The importance of sand in the formation of avulsion channels within experimental fans that develop from sediment mixtures of mud and sand

Science.gov (United States)

Iscen, N.; Strom, K.

2017-12-01

Autogenic channel migration and avulsion has long been recognized as important drivers of alluvial fan dynamics. In the literature, several field studies have documented that the presence and the amount of sand transport through a channel is important for channel incision in alluvial fans and deltas. In our experiments, we present the general autogenic avulsion cycle of experimental alluvial fans with mixtures of cohesive sediment and sand with a range of boundary conditions, and we detail the importance of mobile sand fraction in the development of channels that lead to avulsion. Experimental observations demonstrate that new channels form at topographically low regions within the floodplain providing that sand is transported to these topographic lows due to overbank flow or levee breaching. In addition to the sediment transported from upstream, erosion of a previous deposit and an ongoing backfilling nearby are observed as the possible sources of sand getting into the ghost channels. We explore whether the presence of sand is important for channel development because it increases abrasion of the channel or because it changes the roughness characteristics of the flow. We also examine the affect of sediment and water supply change on the newly described channelization process and link distinctive channel morphologies to different stages of described channel development and the avulsion process.

Rheology of oil sands slurries

Energy Technology Data Exchange (ETDEWEB)

Chow, R.; Zhou, J. [Alberta Research Council, Edmonton, AB (Canada). Mineral Oil Sands Unit; Wallace, D. [Dean Wallace Consulting Inc., Beaumont, AB (Canada)

2006-07-01

This study focused on integrating rheology and colloid science to improve recovery of bitumen in surface mined oil sands. Factors that influence recovery, such as conditions of particle interaction, solids concentration and shear rate, were reviewed. In an effort to understand the rheological behaviour of clay-in-water suspensions, an elaborate procedure was developed to separate an inter-bedded clay layer from a site at Albian Sands Energy Inc. The variables were water chemistry, solids concentration, and shear rate. The research study was conducted at the Alberta Research Council with the support of the CONRAD Extraction Group. A controlled stress rheometer was used to provide the quantitative evaluations of the clay slurry properties. The research results indicate that the viscoelastic properties of the slurry are highly influenced by the shear history of the slurry, solids content, calcium concentration, and sample aging. Shear thinning behaviour was observed in all slurry samples, but the slurry viscosity increased with test time for a given shear rate. In order to classify the slurries, a method was developed to distinguish the gel strength. The slurries were then classified into 3 distinct patterns, including no gel, weak gel and strong gel. The evolution of the experimental protocols were described along with the current stability maps that correlate the domains of the gel strength according to the solids concentration, calcium ion content, and shear rate. It was concluded that the rheological properties of oil sands slurries influence bitumen recovery in commercial surface-mined oil sands operations. tabs., figs.

Production of oil from Intermountain West tar sands deposits

Energy Technology Data Exchange (ETDEWEB)

Glassett, J.M.; Glassett, J.A.

1976-03-01

Six tar sand deposits in the Intermountain West, each containing more than one billion barrels of oil in place, are identified. All of these deposits are in eastern Utah and contain a total of twenty-eight billion barrels of oil. The names of the six deposits arranged in descending order of desirability for large-scale surface-mining oil recovery operations are as follows: Sunnyside, Tar Sand Triangle, Asphalt Ridge, P.R. Spring, Circle Cliffs, and Hill Creek. An overview of each deposit is presented including geology, surface-mining variables, chemical processing variables, environmental aspects, and economics. A comparison of Utah tar sands and Athabasca, Alberta, Canada tar sands is also presented.

Therapeutic bronchoscopy in a child with sand aspiration and respiratory failure from near drowning--case report and literature review.

Science.gov (United States)

Kapur, N; Slater, A; McEniery, J; Greer, M L; Masters, I B; Chang, A B

2009-10-01

Foreign matter aspiration occurs relatively commonly in drowning and near-drowning events. In most cases, stomach contents are aspirated. Sand aspiration rarely occurs and there are no reported cases in children with near drowning. Limited data are available on clinical presentation and management of sand aspiration with accidental burial. We report a 3-year-old boy who nearly drowned while swimming in brackish waters and was found face down in sand. Sand aspiration was suspected when the child continued to have persistent wheezing and high ventilatory requirement despite intensive bronchodilator and corticosteroids therapy with an inability to wean after 4 days post-near-drowning event. Radiology was non-specific in the absence of sand bronchogram. Presence of sand in the airways was confirmed when a bronchoscopy was undertaken and sand seen in the bronchoalveolar lavage fluid. Sequential lung washing followed by exogenous surfactant administration (3 ml/kg) was undertaken and lead to significant improvement such that within 12 hr post-therapeutic lavage, his ventilatory requirements reduced substantially. The child was extubated 4 days post-lavage and on review 2 months post-event, was clinically well with airway resistance within normal predicted values measured on forced oscillatory spirometry (IOS).

Investigation into the Heat of Hydration and Alkali Silica Reactivity of Sustainable Ultrahigh Strength Concrete with Foundry Sand

Directory of Open Access Journals (Sweden)

Federico Aguayo

2017-01-01

Full Text Available This study presents the hydration reactivity and alkali silica reaction (ASR of ultrahigh strength concrete (UHSC that has been made more sustainable by using spent foundry sand. Spent foundry sand not only is sustainable but has supplementary cementitious material (SCM characteristics. Two series of UHSC mixtures were prepared using a nonreactive and reactive sand (in terms of ASR to investigate both the impact of a more reactive aggregate and the use of spent foundry sand. Conduction calorimetry was used to monitor the heat of hydration maintained under isothermal conditions, while ASR was investigated using the accelerated mortar bar test (AMBT. Additionally, the compressive strengths were measured for both series of mixtures at 7, 14, and 28 days to confirm high strength requirements. The compressive strengths ranged from 85 MPa (12,345 psi to 181.78 MPa (26,365 psi. This result demonstrates that a UHSC mixture was produced. The calorimetry results revealed a slight acceleration in the heat of hydration flow curve compared to the control from both aggregates indicating increased hydration reactivity from the addition of foundry waste. The combination of foundry sand and reactive sand was found to increase ASR reactivity with increasing additions of foundry sand up to 30% replacement.

A Laboratory Experiment on the Evolution of a Sand Gravel Reach Under a Lack of Sediment Supply

Science.gov (United States)

Orru, C.; Chavarrias, V.; Ferrara, V.; Blom, A.

2014-12-01

A flume experiment was conducted to examine the evolution of a sand-gravel reach under a lack of sediment supply. The experimental data are used to validate a numerical sand-gravel model. A bed composed of a bi-modal sediment mixture is installed with a uniform slope and an imposed gradual fining pattern. Initially, the sand fraction gradually increases in streamwise direction until the bed is fully composed of sand. The water discharge and downstream water level were constant, and the sediment feed rate was equal to zero. The experiment was dominated by bed load, partial transport, and a subcritical flow regime was imposed. The flow rate was such that only sand was mobile (partial transport), which led to a coarsening over the upstream reach and a gradual reduction of the sediment transport rate during the experiment. New equipment was used to measure the evolution of the grain size distribution of the bed surface during the experiment over the entire flume using image analysis. In the upstream reach we observed a gradual coarsening over time and the formation of an armour layer, which resulted in a more abrupt transition in grain size of the bed surface. Bed degradation increased in streamwise direction. This is due to the initial streamwise increase in the availability of sand in the bed. The different volume fraction content of sand in the bed allowed for the gravel to sink more in the downstream part of the upstream reach. The sand reach suffered from a larger degradation. Finally, we see one reach dominated by sand, small bedforms, and a small bed slope, and a gravel reach dominated by a larger bed slope.

Sand and Gravel Operations

Data.gov (United States)

Department of Homeland Security — This map layer includes sand and gravel operations in the United States. These data were obtained from information reported voluntarily to the USGS by the aggregate...

A Threshold Continuum for Aeolian Sand Transport

Science.gov (United States)

Swann, C.; Ewing, R. C.; Sherman, D. J.

2015-12-01

The threshold of motion for aeolian sand transport marks the initial entrainment of sand particles by the force of the wind. This is typically defined and modeled as a singular wind speed for a given grain size and is based on field and laboratory experimental data. However, the definition of threshold varies significantly between these empirical models, largely because the definition is based on visual-observations of initial grain movement. For example, in his seminal experiments, Bagnold defined threshold of motion when he observed that 100% of the bed was in motion. Others have used 50% and lesser values. Differences in threshold models, in turn, result is large errors in predicting the fluxes associated with sand and dust transport. Here we use a wind tunnel and novel sediment trap to capture the fractions of sand in creep, reptation and saltation at Earth and Mars pressures and show that the threshold of motion for aeolian sand transport is best defined as a continuum in which grains progress through stages defined by the proportion of grains in creep and saltation. We propose the use of scale dependent thresholds modeled by distinct probability distribution functions that differentiate the threshold based on micro to macro scale applications. For example, a geologic timescale application corresponds to a threshold when 100% of the bed in motion whereas a sub-second application corresponds to a threshold when a single particle is set in motion. We provide quantitative measurements (number and mode of particle movement) corresponding to visual observations, percent of bed in motion and degrees of transport intermittency for Earth and Mars. Understanding transport as a continuum provides a basis for revaluating sand transport thresholds on Earth, Mars and Titan.

Differential effects of a local industrial sand lance fishery on seabird breeding performance

DEFF Research Database (Denmark)

Frederiksen, M.; Jensen, Henrik; Daunt, F.

2008-01-01

fluctuations. We evaluated the effects of an industrial sand lance (Ammodytes marinus) fishery off the North Sea coast of the United Kingdom, which has been opened and closed in a quasi-experimental fashion, on sand-lance-dependent breeding seabirds. Controlling for environmental variation ( sea surface...... or to the fact that only one study colony in the control zone was exposed to high fishery effort within the typical foraging range of Kittiwakes during the breeding season. The strong impact on Kittiwakes, but not on diving species, could result from ( 1) inherently high sensitivity to reduced prey availability...

Presence of Campylobacter and Salmonella in sand from bathing beaches.

Science.gov (United States)

Bolton, F J; Surman, S B; Martin, K; Wareing, D R; Humphrey, T J

1999-02-01

The purpose of this study was to determine the presence of thermophilic Campylobacter spp. and Salmonella spp. in sand from non-EEC standard and EEC standard designated beaches in different locations in the UK and to assess if potentially pathogenic strains were present. Campylobacter spp. were detected in 82/182 (45%) of sand samples and Salmonella spp. in 10/182 (6%). Campylobacter spp. were isolated from 46/92 (50%) of samples from non-EEC standard beaches and 36/90 (40%) from EEC standard beaches. The prevalence of Campylobacter spp. was greater in wet sand from both types of beaches but, surprisingly, more than 30% of samples from dry sand also contained these organisms. The major pathogenic species C. jejuni and C. coli were more prevalent in sand from non-EEC standard beaches. In contrast, C. lari and urease positive thermophilic campylobacters, which are associated with seagulls and other migratory birds, were more prevalent in sand from EEC standard beaches. Campylobacter isolates were further characterized by biotyping and serotyping, which confirmed that strains known to be of types associated with human infections were frequently found in sand on bathing beaches.

Preliminary fingerprinting analysis of Alberta oil sands and related petroleum products

International Nuclear Information System (INIS)

Yang, C.; Wang, Z.D.; Hollebone, B.; Brown, C.E.; Yang, Z.Y.; Landriault, M.; Fieldhouse, B.

2009-01-01

This paper reported on a study that presented a preliminary quantitative chemical characterization of Alberta oil sands and many other related Alberta oils such as oil sand bitumen, Cold Lake bitumen, Albian heavy synthetic crude, and Alberta Mixed sweet blend. The rapid increase in production of the Alberta oil sands has resulted in unprecedented environmental concern. The mining, extraction and production of oil sands such resulted in huge consumption of water resources, huge emission of greenhouse gas and large number of tailings ponds. In addition, accidental spills in the transportation and usage of oil sands will potentially cause considerable impact on the environment. It is therefore essential to have the ability to characterize Alberta oil sands and their oil products. The specific chemical properties of the oil sands bitumen must be known. Therefore, this study collected quantitative data on the concentration and distribution profiles of target compounds in Alberta oil sands and its petroleum products. The chemical fingerprints of 5 Alberta oil sands and their related petroleum products were studied using gas chromatography/flame ionization detection (GC/FID) and gas chromatography/mass spectrometry (GC/MS). The characterized hydrocarbons were n-alkanes; target alkylated PAHs and other EPA priority PAHs; biomarker terpanes and steranes; and bicyclic sesquiterpanes. The information acquired during this study will provide the basis for oil-oil correlation and differentiation in future environmental applications relevant to oil sands. 24 refs., 6 tabs., 4 figs.

Economic impacts of Alberta's oil sands, volume 1

International Nuclear Information System (INIS)

Timilsina, G.R.; LeBlanc, N.; Walden, T.

2005-01-01

In 2004, the international media recognized Alberta's oil sands as part of the global oil reserves, thereby establishing Canada as second to Saudi Arabia as potential oil producing nations. The economic impacts of Alberta's oil sands industry on economies were assessed at regional, provincial and international levels for the 2000 to 2020 period. A customized input-output model was used to assess economic impacts, which were measured in terms of changes in gross domestic product; employment and labour income; and, government revenues. Cumulative impacts on employment by sector and by jurisdiction were also presented. An investment of $100 billion is expected through 2020, resulting in production of crude bitumen and synthetic crude oil outputs valued at about $531 billion. The impact of the oil sands industry on local employment was also evaluated. It was shown that activities in the oil sands industry will lead to significant economic impact in Alberta, Ontario, Quebec and the rest of Canada. Alberta's local economy would be the main beneficiary of oil sands activities with nearly 3.6 million person years employment created in Alberta during the 2000 to 2020. Another 3 million person years employment would be created in other Canadian provinces and outside Canada during the same time period. A sensitivity analysis on the responsiveness to oil prices and the removal of various constraints incorporated in the main analysis was also presented. The federal government will be the largest recipient of revenues generated to to oil sands activities. The results of the study were compared with that of the National Task Force on Oil Sands Strategies. This first volume revealed the results of the study while the second volume includes the data and detailed results. 48 refs., 57 tabs., 28 figs

Phase behavior of methane hydrate in silica sand

International Nuclear Information System (INIS)

Sun, Shi-Cai; Liu, Chang-Ling; Ye, Yu-Guang; Liu, Yu-Feng

2014-01-01

Highlights: • Hydrate p-T trace in coarse-grained sediment is consistent with that in bulk water. • Fine-grained sediment affects hydrate equilibrium for the depressed water activity. • Hydrate equilibrium in sediment is related to the pore size distribution. • The application of hydrate equilibrium in sediment depends on the actual condition. -- Abstract: Two kinds of silica sand powder with different particle size were used to investigate the phase behavior of methane hydrate bearing sediment. In coarse-grained silica sand, the measured temperature and pressure range was (281.1 to 284.2) K and (5.9 to 7.8) MPa, respectively. In fine-grained silica sand, the measured temperature and pressure range was (281.5 to 289.5) K and (7.3 to 16.0) MPa, respectively. The results show that the effect of coarse-grained silica sand on methane hydrate phase equilibrium can be ignored; however, the effect of fine-grained silica sand on methane hydrate phase equilibrium is significant, which is attributed to the depression of water activity caused by the hydrophilicity and negatively charged characteristic of silica particle as well as the pore capillary pressure. Besides, the analysis of experimental results using the Gibbs–Thomson equation shows that methane hydrate phase equilibrium is related to the pore size distribution of silica sand. Consequently, for the correct application of phase equilibrium data of hydrate bearing sediment, the geological condition and engineering requirement should be taken into consideration in gas production, resource evaluation, etc

Geophysical applications for oil sand mine tailings management

Energy Technology Data Exchange (ETDEWEB)

Parker, D.; Bauman, P. [WorleyParsons, Calgary, AB (Canada)

2009-07-01

Geophysical techniques are applied throughout a mine's life cycle to facilitate siting, constructing and monitoring of tailings dumps and ponds. This presentation described 3 case studies from the Athabasca region in northeast Alberta that demonstrated some of the concerns associated with oil sand mine tailings, and the information that geophysical surveys can provide. The objectives of these studies were to determine the lateral and depth extents of elevated conductivities of soil and groundwater that have high salt concentration from the tailings sand pore fluid. Due to high chloride concentrations within the tailings material, salt within the root zone may affect vegetation. A terrain conductivity survey was designed to map the lateral extents of salinity impact, while an electrical resistivity tomography (ERT) survey was used to delineate the tailings sand leachate at depth. The proper management of oil sand tailings facilities is vital to the life cycle of a mine. It was concluded that geophysical techniques can be instrumental in managing several engineering and environmental challenges, from Pleistocene channel mapping, to tailings pond settling characteristics, to reclaiming tailings sands. 1 ref., 7 figs.

Dewatering Behaviour of Fine Oil Sands Tailings : An Experimental Study

NARCIS (Netherlands)

Yao, Y.

2016-01-01

Oil sands tailings are a warm aqueous suspension of sand, silt, clay, residual bitumen and naphtha. The tailings are hydraulically transported and stored in tailing ponds where they segregate, with the sand settling from suspension forming beaches and the remaining tailings flowing to the middle of

Seasonal changing sand waves and the effect of surface waves

NARCIS (Netherlands)

Sterlini, Fenneke; van Dijk, Thaiënne A.G.P.; IJzer, Steven; Hulscher, Suzanne; Schüttrumpf, Holger; Tomasicchio, Guiseppe Roberto

2012-01-01

Sand waves are wavelike subaqueous sediment structures that exist in large areas in shelf seas. Due to their characteristics sand waves can severely affect human offshore activities, such as navigation. This makes it important to understand the physical processes that shape and change sand waves. In

Acetylcholinesterase mutations and organophosphate resistance in sand flies and mosquitoes

Science.gov (United States)

Leishmaniasis is an insect-borne disease caused by several protozoan species in the genus Leishmania, which are vectored by sand fly species in the genera Phlebotomus or Lutzomyia, depending on the sand fly species geographic range. Sand fly bites and leishmaniasis significantly impacted U.S. milita...

EFFECTS OF A SAND RUNNING SURFACE ON THE KINEMATICS OF SPRINTING AT MAXIMUM VELOCITY

Directory of Open Access Journals (Sweden)

P E Alcaraz

2011-05-01

Full Text Available Performing sprints on a sand surface is a common training method for improving sprint-specific strength. For maximum specificity of training the athlete’s movement patterns during the training exercise should closely resemble those used when performing the sport. The aim of this study was to compare the kinematics of sprinting at maximum velocity on a dry sand surface to the kinematics of sprinting on an athletics track. Five men and five women participated in the study, and flying sprints over 30 m were recorded by video and digitized using biomechanical analysis software. We found that sprinting on a sand surface was substantially different to sprinting on an athletics track. When sprinting on sand the athletes tended to ‘sit’ during the ground contact phase of the stride. This action was characterized by a lower centre of mass, a greater forward lean in the trunk, and an incomplete extension of the hip joint at take-off. We conclude that sprinting on a dry sand surface may not be an appropriate method for training the maximum velocity phase in sprinting. Although this training method exerts a substantial overload on the athlete, as indicated by reductions in running velocity and stride length, it also induces detrimental changes to the athlete’s running technique which may transfer to competition sprinting.

Dark grains of sand: a geological storytelling

Science.gov (United States)

Gallo Maresca, Magda

2017-04-01

In the secondary Italian school the Earth science learning begins at first year, in synergy with other natural science subjects such as Astronomy, Chemistry and Biology. Italian teachers have to focus on the landscape geomorphological aspects and often Earth processes are difficult to display since they are related to certain phenomena happened during the past and often far from the involved country. In order to better understand the environment surrounding us, very simple and poor materials, like sands, allow the teachers to create attractive lab experiences. According to the IBSE (Inquiry Based Science Education) approach, a learning unit has been implemented starting from a walking along the light carbonate beaches of the Adriatic sea: a smart look to the sands ("engage step"), stroke the students fantasy pushing them to explore some strange black grains on the sands. Dirty sands? Or rock landscape, soil degradation and Ofanto river and coastal processes (erosion, transportation and deposition)? This was the teaching challenge. Due to the youngest age, a third level, guided inquiry, was adopted so the teacher is the "guide of inquiry" encouraging the students using the research question ("Why is the sand dark?", "Do all sands look the same?", "Where does it come from?") and driving the students around their investigation plans ("How can I measure grain size?"). A procedure to answer the above questions and validate the results and explanations has been implemented to allow the students to be proactive in their study. During the learning activities will be the students to ask for field trip to elaborate their new knowledge, verify and visualize the speculated processes. The teaching skills allow to address several geosciences domains such as mineralogy, petrology, regional geology and geodynamics as well as other scientific disciplines such as mathematics (more specifically statistics), forensic science and even life sciences (the presence of bioclasts might

Investigations of Physicochemical Properties and Thermal Utilisation of Dusts Generated in the Mechanical Reclamation Process of Spent Moulding Sands

Directory of Open Access Journals (Sweden)

Dańko R.

2015-04-01

Full Text Available The after reclamation dusts originated from various foundry plants, applying moulding sands with organic binding agents, mostly resins, are characterised by different properties in dependence of the used binders, reclamation systems, spent sands overheating degree and the efficiency of the system dedusting the reclaimed material operating in individual foundry plants.

Use of digital image analysis combined with fractal theory to determine particle morphology and surface texture of quartz sands

Directory of Open Access Journals (Sweden)

Georgia S. Araujo

2017-12-01

Full Text Available The particle morphology and surface texture play a major role in influencing mechanical and hydraulic behaviors of sandy soils. This paper presents the use of digital image analysis combined with fractal theory as a tool to quantify the particle morphology and surface texture of two types of quartz sands widely used in the region of Vitória, Espírito Santo, southeast of Brazil. The two investigated sands are sampled from different locations. The purpose of this paper is to present a simple, straightforward, reliable and reproducible methodology that can identify representative sandy soil texture parameters. The test results of the soil samples of the two sands separated by sieving into six size fractions are presented and discussed. The main advantages of the adopted methodology are its simplicity, reliability of the results, and relatively low cost. The results show that sands from the coastal spit (BS have a greater degree of roundness and a smoother surface texture than river sands (RS. The values obtained in the test are statistically analyzed, and again it is confirmed that the BS sand has a slightly greater degree of sphericity than that of the RS sand. Moreover, the RS sand with rough surface texture has larger specific surface area values than the similar BS sand, which agree with the obtained roughness fractal dimensions. The consistent experimental results demonstrate that image analysis combined with fractal theory is an accurate and efficient method to quantify the differences in particle morphology and surface texture of quartz sands.

Assessing environmental impacts of inland sand mining in parts of ...

African Journals Online (AJOL)

Sand is a valuable resource for construction and other purposes, however sand mining often result in serious environmental problems such as land degradation, loss of agricultural lands and biodiversity, as well increased poverty among people. This study assessed the environmental impacts of inland sand mining in six ...

Locomotion of Stramonita haemastoma (Linnaeus (Gastropoda, Muricidae on a mixed shore of rocks and sand

Directory of Open Access Journals (Sweden)

Marcos G. Papp

2001-03-01

Full Text Available Mixed shores of rocks and sand are appropriate systems for the study of limitations that the isolation of rocks may impose for gastropods that typically inhabit rocky shores. We marked 52 Stramonita haemastoma (Linnaeus, 1767 snails on a mixed shore and found that 34 of them moved between rocks one to four times during 15 surveys in a period of 72 days. In the experiments, the snails moved on rock by continuous, direct, ditaxic, alternate undulations of the foot sole but on submerged sand they used slower arrhythmic discontinuous contractions of the foot sole. They switched between modes of locomotion in response to the type and topography of the substrate and possibly to water dynamics. In nature, snails moved between rocks forming aggregations where they oviposited. This may have masked other causes of movement, such as availability of prey. Most snails burrowed into the sand when the rocks became exposed during low tides. Further experiments are needed to explicitly address the possible causes of movements among rocks and burial.

Efficiency of Micro-fine Cement Grouting in Liquefiable Sand

International Nuclear Information System (INIS)

Mirjalili, Mojtaba; Mirdamadi, Alireza; Ahmadi, Alireza

2008-01-01

In the presence of strong ground motion, liquefaction hazards are likely to occur in saturated cohesion-less soils. The risk of liquefaction and subsequent deformation can be reduced by various ground improvement methods including the cement grouting technique. The grouting method was proposed for non-disruptive mitigation of liquefaction risk at developed sites susceptible to liquefaction. In this research, a large-scale experiment was developed for assessment of micro-fine cement grouting effect on strength behavior and liquefaction potential of loose sand. Loose sand samples treated with micro-fine grout in multidirectional experimental model, were tested under cyclic and monotonic triaxial loading to investigate the influence of micro-fine grout on the deformation properties and pore pressure response. The behavior of pure sand was compared with the behavior of sand grouted with a micro-fine cement grout. The test results were shown that cement grouting with low concentrations significantly decreased the liquefaction potential of loose sand and related ground deformation

Experimental studies in Ultrasonic Pulse Velocity of roller compacted concrete pavement containing fly ash and M-sand

Directory of Open Access Journals (Sweden)

S. Krishna Rao

2016-07-01

Full Text Available This paper presents the experimental investigation results of Ultrasonic Pulse Velocity (UPV tests conducted on roller compacted concrete pavement (RCCP material containing Class F fly ash of as mineral admixture. River sand, M-sand and combination of M-sand and River sand are used as fine aggregate in this experimental work. Three types of fly ash roller compacted concrete mixes are prepared using above three types of fine aggregates and they are designated as Series A (River sand, Series B (manufactured sand and Series C (combination of River sand and M-sand. In each series the fly ash content in place of cement is varied from 0% to 60%. In each series and for different ages of curing (i.e 3, 7, 28 and 90 days forty two cube specimens are cast and tested for compressive strength and UPV. The UPV results of fly ash containing roller compacted concrete pavement (FRCCP show lower values at all ages from 3 days to 90 days in comparison with control mix concrete (0% fly ash in all mixes. However, it is also observed that Series B and C mixes containing fly ash show better results in UPV values, compressive strength and Dynamic Elastic Modulus in comparison to Series A mixes with fly ash. Relationships between compressive strength of FRCCP and UPV and Dynamic Elastic Modulus are proposed for all series mixes. A new empirical equation is proposed to determine the Dynamic Elastic Modulus of FRCCP. Keywords: Compressive strength, Dynamic Elastic Modulus, Fly ash, Roller compacted concrete pavement, Ultrasonic Pulse Velocity

Sustainable water management in Alberta's oil sands

Energy Technology Data Exchange (ETDEWEB)

Byers, Bill; Usher, Robyn; Roach, Andrea [CH2M HILL, Englewood, CO (United States); Lambert, Gord; Kotecha, Prit [Suncor Energy Inc., Calgary (Canada)

2012-07-01

The Canadian Association of Petroleum Producers forecast published in 2011 predicts that oil production from oil sands will increase by 50% in the next 3 years and double by 2020. This rate of growth will result in significant pressure on water resources; water use per barrel of oil sands production is comparable to other energy resources - about 2.5 barrels of fresh water per barrel of oil produced are used by mining operations and 0.5 barrels by in-situ operations. Suncor Energy Inc. (Suncor) was the first company to develop the oil sands in northern Alberta and holds one of the largest oil sands positions in Canada. In 2010, Suncor announced plans to increase production to more than 1 million barrels of oil equivalent per day by 2020, which it plans to achieve through oil sands production growth of approximately 10% per year. Because water supply and potential impacts to water quality are critical to its future growth, in 2010-2011 Suncor conducted a risk assessment to identify water-related business risks related to its northern Alberta operations. The assessment identified more than 20 high level business risks in strategic water risk areas including water supply, water reuse, storm water management, groundwater, waste management and river water return. The risk assessment results prompted development of a strategic roadmap to guide water stewardship across Suncor's regional operations. The roadmap describes goals, objectives, and specific activities for each of six key water risk areas, and informs prioritization and selection of prospective water management activities. Suncor is not only exploring water within its own boundaries, but is also collaborating with other oil sands producers to explore ways of integrating its water systems through industry consortia; Suncor is a member of the Oil Sands Leadership Initiative and of the recently formed Canadian Oil Sands Innovation Alliance, among others. (author)

PERENCANAAN SAND POCKET SEBAGAI BANGUNAN PENGENDALI ALIRAN SEDIMEN DI KALI OPAK YOGYAKARTA

Directory of Open Access Journals (Sweden)

Yeri Sutopo

2016-07-01

Full Text Available This research conducted in Opak River, in Yogyakarta. This river has broad (river flow area 27,04 km2, and 20,11 km in length. The research objective is to make a planning about effective rainfall in 50 years and found the Opak Sand Pocket design. This research used methods with direct-survey in location, and collected secondary data from related agencies. From the data, it was obtained the value of precipitation the design, discharge flood design, dimensions of building hydrolic design (Main Dam, Sub Dam, Apron, and analysis the effectiveness of sand pocket in reducing the sediment that has happened. Based on the results of the research, discharge maximum ( Q50 that occurs in the river of 202,77 m3/s. So it can be calculated that sand pocket designed will have wide of apron 54,04 m, with total high of Main Dam 6 m, total high of Sub Dam 6 m, length of apron 10 m, thick of apron 0,96 m. Based on the ability of sand pocket in reducing the rate of the sediment that is happened, the building has effectiveness until 90,20 % in reducing bed load based on the calculation. Therefore, it can be argued that the building has been effective to reduce the speed of sediment occurring in Opak River.

Synthesis and characterization of silica gel from siliceous sands of southern Tunisia

Directory of Open Access Journals (Sweden)

Ali Sdiri

2014-09-01

Full Text Available The present work aimed to achieve valorization of Albian sands for the preparation of sodium silicates that are commonly used as a precursor to prepare silica gel. A siliceous sand sample was mixed with sodium carbonate and heated at a high temperature (1060 °C to prepare sodium silicates. The sodium silicates were dissolved in distilled water to obtain high quality sodium silicate solution. Hydrochloric acid was then slowly added to the hydrated sodium silicates to obtain silica gel. The collected raw siliceous sands, as well as the prepared silica gels, were characterized by different techniques, such as X-ray fluorescence (XRF, X-ray diffraction (XRD, scanning electron microscopy (SEM and thermal analysis (DSC. XRF confirmed that the detrital sand deposits of southern Tunisia contain high amounts of silica, with content ranging from 88.8% to 97.5%. The internal porosity varied between 17% and 22%, and the specific surface area was less than 5 m2/g. After the treatment described above, it was observed that the porosity of the obtained silica gel reached 57% and the specific surface area exceeded 340 m2/g. Nitrogen adsorption isotherms showed that the prepared silica gels are microporous and mesoporous materials with high adsorption capacities. These results suggest that the obtained silica gels are promising materials for numerous environmental applications.

Element Geochemical Analysis of the Contribution of Aeolian Sand to Suspended Sediment in Desert Stream Flash Floods

Directory of Open Access Journals (Sweden)

Xiaopeng Jia

2014-01-01

Full Text Available The interaction of wind and water in semiarid and arid areas usually leads to low-frequency flash flood events in desert rivers, which have adverse effects on river systems and ecology. In arid zones, many aeolian dune-fields terminate in stream channels and deliver aeolian sand to the channels. Although aeolian processes are common to many desert rivers, whether the aeolian processes contribute to fluvial sediment loss is still unknown. Here, we identified the aeolian-fluvial cycling process responsible for the high rate of suspended sediment transport in the Sudalaer desert stream in the Ordos plateau of China. On the basis of element geochemistry data analysis, we found that aeolian sand was similar to suspended sediment in element composition, which suggests that aeolian sand contributes to suspended sediment in flash floods. Scatter plots of some elements further confirm that aeolian sand is the major source of the suspended sediment. Factor analysis and the relation between some elements and suspended sediment concentration prove that the greater the aeolian process, the higher the suspended sediment concentration and the greater the contribution of aeolian sand to suspended sediment yield. We conclude that aeolian sand is the greatest contributor to flash floods in the Sudalaer desert stream.

Alberta Oil Sands Equity annual report, 1992-93. Partnership and progress in Alberta's oil sands development

International Nuclear Information System (INIS)

1993-01-01

Alberta Oil Sands Equity (AOSE) manages the Alberta government's equity investments in oil sands and heavy oil projects. AOSE is a 16.74% participant in the Syncrude Project, a 10% participant in the OSLO (Other Six Leases Operation) Commercial Project and the OSLO New Ventures project, and a 24.17% participant in the Lloydminster Bi-Provincial Upgrader. Syncrude produces ca 12% of Canadian crude oil requirements, and AOSE's share yielded $44 million profit for 1992/93, slightly higher than the the $43.3 million the previous year. The OSLO Commercial Project is a proposed commercial oil sands plant with a mine site and extraction plant to be located north of Fort McMurray, and an upgrading facility to be situated north of Edmonton. Work on this project was suspended in early 1992. The OSLO New Ventures project will handle the exploration and development of the remaining five oil sands leases plus the southern portion of Lease 31. As of March 31, 1993, the project owners were considering a commercial demonstration project utilizing dredging and cold-water extraction processes. Two of the owners are unable to provide funding and discussions are under way to resolve the matter and move the program forward. The Lloydminster Bi-Provincial Upgrader opened Noveber 20, 1992, and production has reached 41,000 bbl/d, or 89% of design capacity. The upgrader will increase the value of heavy crude oil and thereby increase its demand. 5 figs., 3 tabs

An investigation of waste foundry sand in asphalt concrete mixtures.

Science.gov (United States)

Bakis, Recep; Koyuncu, Hakan; Demirbas, Ayhan

2006-06-01

A laboratory study regarding the reuse of waste foundry sand in asphalt concrete production by replacing a certain portion of aggregate with WFS was undertaken. The results showed that replacement of 10% aggregates with waste foundry sand was found to be the most suitable for asphalt concrete mixtures. Furthermore, the chemical and physical properties of waste foundry sand were analysed in the laboratory to determine the potential effect on the environment. The results indicated that the investigated waste foundry sand did not significantly affect the environment around the deposition

Insecticide resistance in the sand fly, Phlebotomus papatasi from Khartoum State, Sudan

Directory of Open Access Journals (Sweden)

Hassan Mo'awia

2012-03-01

Full Text Available Abstract Background Phlebotomus papatasi the vector of cutaneous leishmaniasis (CL is the most widely spread sand fly in Sudan. No data has previously been collected on insecticide susceptibility and/or resistance of this vector, and a first study to establish a baseline data is reported here. Methods Sand flies were collected from Surogia village, (Khartoum State, Rahad Game Reserve (eastern Sudan and White Nile area (Central Sudan using light traps. Sand flies were reared in the Tropical Medicine Research Institute laboratory. The insecticide susceptibility status of first progeny (F1 of P. papatasi of each population was tested using WHO insecticide kits. Also, P. papatasi specimens from Surogia village and Rahad Game Reserve were assayed for activities of enzyme systems involved in insecticide resistance (acetylcholinesterase (AChE, non-specific carboxylesterases (EST, glutathione-S-transferases (GSTs and cytochrome p450 monooxygenases (Cyt p450. Results Populations of P. papatasi from White Nile and Rahad Game Reserve were sensitive to dichlorodiphenyltrichloroethane (DDT, permethrin, malathion, and propoxur. However, the P. papatasi population from Surogia village was sensitive to DDT and permethrin but highly resistant to malathion and propoxur. Furthermore, P. papatasi of Surogia village had significantly higher insecticide detoxification enzyme activity than of those of Rahad Game Reserve. The sand fly population in Surogia displayed high AChE activity and only three specimens had elevated levels for EST and GST. Conclusions The study provided evidence for malathion and propoxur resistance in the sand fly population of Surogia village, which probably resulted from anti-malarial control activities carried out in the area during the past 50 years.

Improved soil characterization for pipe piles in sand in API RP-2A

International Nuclear Information System (INIS)

Hossain, M.K.; Briaud, J.L.

1993-01-01

In the offshore, most foundations are steel pipe piles and most of them are designed using the API RP 2A guidelines. For axial capacity of piles in sand the current guidelines in many cases show definite discrepancies when compared against actual load capacities of piles. An updated data base analysis shows that there are three major weaknesses in the current guidelines with respect to soil characterization: (a) the consideration of the lateral earth pressure coefficient, K, as a constant (1.0 or 0.8); (b) the consideration of the unit point bearing resistance, q, as a linear function of depth; and (c) the absence of an unambiguous soil parameter determination process based on reliable in-situ test results. In this paper, specific modifications to the current API RP 2A guidelines are proposed on the basis of a data base analysis to account for the discrepancies arising from (a), (b), and (c) above. These modifications will reduce the discrepancies in the current API RP 2A method and increase the accuracy of the prediction of axial capacity of pipe piles in sand. Furthermore this will make the method fundamentally more consistent with soil behavior in deep foundations

Sand flies of Nicaragua: a checklist and reports of new collections

Directory of Open Access Journals (Sweden)

Russell W Raymond

2010-11-01

Full Text Available Sand flies within the genus Lutzomyia serve as the vectors for all species of the protozoan parasite Leishmania in the New World. In this paper, we present a summary of the 29 species of Lutzomyia and one of Brumptomyia previously reported for Nicaragua and report results of our recent collections of 565 sand flies at eight localities in the country from 2001-2006. Lutzomyia longipalpis was the predominant species collected within the Pacific plains region of western Nicaragua, while Lutzomyia cruciata or Lutzomyia barrettoi majuscula were the species most frequently collected in the central highlands and Atlantic plains regions. The collection of Lutzomyia durani (Vargas & Nájera at San Jacinto in July 2001 is a new record for Nicaragua. Leishmaniasis is endemic to Nicaragua and occurs in three forms: cutaneous, mucocutaneous and visceral leishmaniasis. Cutaneous infections are the most prevalent type of leishmaniasis in Nicaragua and they occur in two different clinical manifestations, typical cutaneous leishmaniasis and atypical cutaneous leishmaniasis, depending on the species of the infecting Leishmania parasite. The distribution of sand flies collected during this study in relation to the geographic distribution of clinical forms of leishmaniasis in the country is also discussed.

Magnetic Characterization of Sand and Boulder Samples from Citarum River and Their Origin

Directory of Open Access Journals (Sweden)

Sudarningsih

2017-09-01

Full Text Available The Citarum River is a nationally strategic river located near Bandung, the capital city of West Java Province. The feasibility of using magnetic methods for monitoring pollution level is currently being tested in the river. Due to its location in a volcanic area, the sediments from the river are expected to be highly magnetic. In this study, sand and boulder samples from Balekambang, a relatively pristine upstream area of the river, were subjected to magnetic and geochemical characterizations to establish the baseline for unpolluted sediments. Such baseline is important for future magnetic monitoring of sediments in the river. The mass-specific magnetic susceptibility of boulder samples was found to be varied from 819.2 to 2340.5 × 10-8m3 kg-1 while that of sand samples varied from 2293.9 to 3845.3 × 10-8m3 kg-1. These high magnetic susceptibility values infer that river sediments are highly magnetic even before being contaminated by industrial and household wastes. The predominant magnetic mineral in sand samples was multi-domain magnetite while that in boulder samples was single to pseudo-single domain magnetite. These differences were supported by the results from petrographic and XRF analyses, implying that the sand and boulder samples originated from different geological formations.

Development, Parameterization, and Validation of a Visco-Plastic Material Model for Sand with DifferentLevels of Water Saturation

Science.gov (United States)

2009-01-01

in essential physics of the tire –sand interactions. Towards that end, a simpler ribbed- tread tire model (described below) of the type often used for...i.e. the deflection and the contact area) on a rigid sur- face. The tire was modelled in the present work using a ribbed- tread tire model similar to...with material properties representing the composite behaviour through the carcass thick - ness. The tread -cap is constructed using linear, hybrid

The stable stiffness triangle - drained sand during deformation cycles

DEFF Research Database (Denmark)

Sabaliauskas, Tomas; Ibsen, Lars Bo

2017-01-01

Cyclic, drained sand stiffness was observed using the Danish triaxial appa- ratus. New, deformation dependant soil property (the stable stiffness triangle) was detected. Using the the stable stiffness triangle, secant stiffness of drained sand was plausible to predict (and control) even during ir...... findings can find application in off-shore, seismic and other engi- neering practice, or inspire new branches of research and modelling wherever dynamic, cyclic or transient loaded sand is encountered....

White Sands, New Mexico as seen from STS-60

Science.gov (United States)

1994-01-01

White Sands National Monument (Park) is easily recognized in the center of this near-vertical color photograph. White Sands is the world's largest gypsum dune field. It represents an alabaster sea that covers nearly 300 square miles. At the southwest corner of the White Sands is dry lake, Lucero. In terms of cultural features the city of Alamogordo and Holloman Air Force Base can be seen with great clarity on this photograph.

Design of dry sand soil stratified sampler

Science.gov (United States)

Li, Erkang; Chen, Wei; Feng, Xiao; Liao, Hongbo; Liang, Xiaodong

2018-04-01

This paper presents a design of a stratified sampler for dry sand soil, which can be used for stratified sampling of loose sand under certain conditions. Our group designed the mechanical structure of a portable, single - person, dry sandy soil stratified sampler. We have set up a mathematical model for the sampler. It lays the foundation for further development of design research.

Log-inject-log in sand consolidation

International Nuclear Information System (INIS)

Murphy, R.P.; Spurlock, J.W.

1977-01-01

A method is described for gathering information for the determination of the adequacy of placement of sand consolidating plastic for sand control in oil and gas wells. The method uses a high neutron cross-section tracer which becomes part of the plastic and uses pulsed neutron logging before and after injection of the plastic. Preferably, the method uses lithium, boron, indium, and/or cadmium tracers. Boron oxide is especially useful and can be dissolved in alcohol and mixed with the plastic ingredients

Re-usage of waste foundry sand in high-strength concrete.

Science.gov (United States)

Guney, Yucel; Sari, Yasin Dursun; Yalcin, Muhsin; Tuncan, Ahmet; Donmez, Senayi

2010-01-01

In this study, the potential re-use of waste foundry sand in high-strength concrete production was investigated. The natural fine sand is replaced with waste foundry sand (0%, 5%, 10%, and 15%). The findings from a series of test program has shown reduction in compressive and tensile strengths, and the elasticity modulus which is directly related to waste foundry inclusion in concrete. Nevertheless the concrete with 10% waste foundry sand exhibits almost similar results to that of the control one. The slump and the workability of the fresh concrete decreases with the increase of the waste foundry sand ratio. Although the freezing and thawing significantly reduces the mechanical and physical properties of the concrete. The obtained results satisfies the acceptable limits set by the American Concrete Institute (ACI). 2010 Elsevier Ltd. All rights reserved.

Parameters of the Two-Phase Sand-Air Stream in the Blowing Process

Directory of Open Access Journals (Sweden)

Danko J.

2012-12-01

Full Text Available Theoretical problems concerning the determination of work parameters of the two-phase sand-air stream in the cores making process by blowing methods as well as experimental methods of determination of the main and auxiliary parameters of this process decisive on the cores quality assessed by the value and distribution of their apparent density are presented in the paper. In addition the results of visualisations of the core-box filling with the sand-air stream, from the blowing chamber, obtained by the process filming by means of the quick-action camera are presented in the paper and compared with the results of simulation calculations with the application of the ProCast software.

Parameters of the Two-Phase Sand-Air Stream in the Blowing Process

Directory of Open Access Journals (Sweden)

J. Danko

2012-12-01

Full Text Available Theoretical problems concerning the determination of work parameters of the two-phase sand-air stream in the cores making process byblowing methods as well as experimental methods of determination of the main and auxiliary parameters of this process decisive on thecores quality assessed by the value and distribution of their apparent density are presented in the paper. In addition the results of visualisations of the core-box filling with the sand-air stream, from the blowing chamber, obtained by the process filming by means of the quick-action camera are presented in the paper and compared with the results of simulation calculations with the application of the ProCast software.

Sand transport in urbanized beaches - models and reality

International Nuclear Information System (INIS)

Pineiro, G.; Norbis, W.; Panario, D.

2012-01-01

The general objective is to quantify the wind transport of sand in the urbanized beaches. The specific objectives include testing and calibration of the wind velocity as well as the classification of the beaches according to the magnitude and the direction of sand transport

[Research on Oil Sands Spectral Characteristics and Oil Content by Remote Sensing Estimation].

Science.gov (United States)

You, Jin-feng; Xing, Li-xin; Pan, Jun; Shan, Xuan-long; Liang, Li-heng; Fan, Rui-xue

2015-04-01

Visible and near infrared spectroscopy is a proven technology to be widely used in identification and exploration of hydrocarbon energy sources with high spectral resolution for detail diagnostic absorption characteristics of hydrocarbon groups. The most prominent regions for hydrocarbon absorption bands are 1,740-1,780, 2,300-2,340 and 2,340-2,360 nm by the reflectance of oil sands samples. These spectral ranges are dominated by various C-H overlapping overtones and combination bands. Meanwhile, there is relatively weak even or no absorption characteristics in the region from 1,700 to 1,730 nm in the spectra of oil sands samples with low bitumen content. With the increase in oil content, in the spectral range of 1,700-1,730 nm the obvious hydrocarbon absorption begins to appear. The bitumen content is the critical parameter for oil sands reserves estimation. The absorption depth was used to depict the response intensity of the absorption bands controlled by first-order overtones and combinations of the various C-H stretching and bending fundamentals. According to the Pearson and partial correlation relationships of oil content and absorption depth dominated by hydrocarbon groups in 1,740-1,780, 2,300-2,340 and 2,340-2,360 nm wavelength range, the scheme of association mode was established between the intensity of spectral response and bitumen content, and then unary linear regression(ULR) and partial least squares regression (PLSR) methods were employed to model the equation between absorption depth attributed to various C-H bond and bitumen content. There were two calibration equations in which ULR method was employed to model the relationship between absorption depth near 2,350 nm region and bitumen content and PLSR method was developed to model the relationship between absorption depth of 1,758, 2,310, 2,350 nm regions and oil content. It turned out that the calibration models had good predictive ability and high robustness and they could provide the scientific

The Impact of Microwave Penetration Depth on the Process of Heating the Moulding Sand with Sodium Silicate

Directory of Open Access Journals (Sweden)

Nowak D.

2017-12-01

Full Text Available This paper presents the impact of microwave penetration depth on the process of heating the moulding sand with sodium silicate. For each material it is affected by: the wavelength in vacuum and the real and imaginary components of the relative complex electrical permittivity εr for a selected measurement frequency. Since the components are not constant values and they change depending on the electrical parameters of materials and the frequency of the electromagnetic wave, it is indispensable to carry out laboratory measurements to determine them. Moreover, the electrical parameters of materials are also affected by: temperature, packing degree, humidity and conductivity. The measurements of the dielectric properties of moulding sand with sodium silicate was carried out using the perturbation method on a stand of waveguide resonance cavity. The real and imaginary components of the relative complex electrical permittivity was determined for moulding sand at various contents of sodium silicate and at various packing degrees of the samples. On the basis of the results the microwave penetration depth of moulding sand with sodium silicate was established. Relative literature contains no such data that would be essential to predicting an effective process of microwave heating of moulding sand with sodium silicate. Both the packing degree and the amount of sodium silicate in moulding sand turned out to affect the penetration depth, which directly translates into microwave power density distribution in the process of microwave heating of moulding sand with sodium silicate.

Geophysics comes of age in oil sands development

Energy Technology Data Exchange (ETDEWEB)

Bauman, P. [WorleyParsons Komex, Calgary, AB (Canada); Birch, R.; Parker, D.; Andrews, B. [Calgary Univ., AB (Canada). Dept. of Geology and Geophysics

2008-07-01

This paper discussed geophysical techniques developed for oil sands exploration and production applications in Alberta's oil sands region. Geophysical methods are playing an important role in mine planning, tailings containment, water supply, and land reclamation activities. Geophysics techniques are used to estimate the volume of muskeg that needs to be stripped and stored for future reclamation activities as well as to site muskeg piles and delineate the thickness of clay Clearwater formations overlying Cretaceous oil-bearing sands. 2-D electrical resistivity mapping is used to map river-connected deep bedrock Pleistocene paleovalleys in the region. Geophysical studies are also used to investigate the interiors of dikes and berms as well as to monitor salt migration within tailings piles. Sonic and density logs are used to create synthetic seismograms for mapping the Devonian surface in the region. The new applications included the calculation of bitumen saturation from surface sands and shales; muskeg thickness mapping; and non-intrusive monitoring of leachate plumes. Geophysical techniques included 2-D electrical resistivity imaging; transient electromagnetic (EM) technologies; ground penetrating radar; and high-resolution seismic reflections. Polarization, surface nuclear magnetic resonance and push-probe sensing techniques were also discussed. Techniques were discussed in relation to Alberta's Athabasca oil sands deposits. 4 refs.

Seismic stochastic inversion identify river channel sand body

Science.gov (United States)

He, Z.

2015-12-01

The technology of seismic inversion is regarded as one of the most important part of geophysics. By using the technology of seismic inversion and the theory of stochastic simulation, the concept of seismic stochastic inversion is proposed.Seismic stochastic inversion can play an significant role in the identifying river channel sand body. Accurate sand body description is a crucial parameter to measure oilfield development and oilfield stimulation during the middle and later periods. Besides, rational well spacing density is an essential condition for efficient production. Based on the geological knowledge of a certain oilfield, in line with the use of seismic stochastic inversion, the river channel sand body in the work area is identified. In this paper, firstly, the single river channel body from the composite river channel body is subdivided. Secondly, the distribution of river channel body is ascertained in order to ascertain the direction of rivers. Morever, the superimposed relationship among the sand body is analyzed, especially among the inter-well sand body. The last but not at the least, via the analysis of inversion results of first vacuating the wells and continuous infilling later, it is meeted the most needs well spacing density that can obtain the optimal inversion result. It would serve effective guidance for oilfield stimulation.

An introduction to conservation and reclamation at Alberta's mineable oil sands

Energy Technology Data Exchange (ETDEWEB)

Richens, T. [Alberta Environment, Edmonton, AB (Canada)

2009-07-01

This paper presented a balanced view of the conservation and reclamation issues and challenges facing oil sands development in Alberta. Bitumen is recovered by truck and shovel in the shallow oil sands of the Athabasca region. The deeper deposits in the Athabasca, Peace River and Cold Lake regions are accessed primarily using a system of horizontal wells and steam to extract the bitumen from the sand and pump it to the surface. Individual in-situ operations have a smaller environmental impact than mines, and do not produce tailings ponds. However, the footprint of in-situ facilities will accumulate over time because of the potential for extensive future development. The key issues facing conservation and reclamation in the mineable oil sands were discussed. Summary statistics on land disturbed and reclaimed in the region were also provided. The challenges facing reclamation activities include long timeframes; large scale, regional planning and integration; competing land use goals; revegetation; byproduct management; and tailings and process-affected water. Multi-stakeholder forums have proven to be the key to the progression of monitoring, research and development and the sharing of knowledge and information. Frameworks have been developed for the assessment of pre-disturbed and reclaimed soil capability specific to the oil sands region. Additional resources are also available, such as guidelines for the reclamation of terrestrial and wetland habitats that represent the best management practices for reclamation research in revegetation, soil salvage, stockpiling and placement, tailings reclamation, end pit lakes, wetlands and biodiversity. 16 refs., 1 fig.

Beach Sand Analysis for Indicators of Microbial Contamination

Science.gov (United States)

Traditional beach monitoring has focused on water quality, with little attention paid to health risks associated with beach sand. Recent research has reported that fecal indicator bacteria, as well as human pathogens can be found in beach sand and may constitute a risk to human h...

Proceedings of the Canadian oil sands forum 2007 : creating excellence through innovation

International Nuclear Information System (INIS)

2007-01-01

The supply from Canada's oil sands industry is growing at an accelerated pace. This conference was intended for professionals in the oil sands industry seeking updated information on oil sands developments, transportation issues and future market challenges and opportunities. It was attended by a broad range of industry participants who addressed some of the critical issues involved in developing oil sands projects. Despite market opportunities which have resulted in a fast pace of development and continually evolving project plans, there are challenges and uncertainties that must be overcome in order to achieve projected levels of supply growth. It was noted that the business environment in the oil sands industry is continually changing in terms of current supply/market/refining situations and new market developments. The conference also addressed how capital cost and mega-project management issues are being addressed. Expanding market opportunities for Canada's growing oil sands supply were highlighted along with latest developments related to upgrading strategies. Market experts also discussed issues related to synthetic crude, heavy oil markets and the supply and demand of diluents. The sessions were entitled: challenges and opportunities in oil sands; oil sands business outlook; latest project development updates; integration of Canadian oil sands with U.S. refining; and, technology and oil sands innovations.The conference featured 16 presentations, of which 6 have been catalogued separately for inclusion in this database. tabs., figs

Determining mineralogical variations of aeolian deposits using thermal infrared emissivity and linear deconvolution methods

Science.gov (United States)

Hubbard, Bernard E.; Hooper, Donald M.; Solano, Federico; Mars, John C.

2018-01-01

We apply linear deconvolution methods to derive mineral and glass proportions for eight field sample training sites at seven dune fields: (1) Algodones, California; (2) Big Dune, Nevada; (3) Bruneau, Idaho; (4) Great Kobuk Sand Dunes, Alaska; (5) Great Sand Dunes National Park and Preserve, Colorado; (6) Sunset Crater, Arizona; and (7) White Sands National Monument, New Mexico. These dune fields were chosen because they represent a wide range of mineral grain mixtures and allow us to gauge a better understanding of both compositional and sorting effects within terrestrial and extraterrestrial dune systems. We also use actual ASTER TIR emissivity imagery to map the spatial distribution of these minerals throughout the seven dune fields and evaluate the effects of degraded spectral resolution on the accuracy of mineral abundances retrieved. Our results show that hyperspectral data convolutions of our laboratory emissivity spectra outperformed multispectral data convolutions of the same data with respect to the mineral, glass and lithic abundances derived. Both the number and wavelength position of spectral bands greatly impacts the accuracy of linear deconvolution retrieval of feldspar proportions (e.g. K-feldspar vs. plagioclase) especially, as well as the detection of certain mafic and carbonate minerals. In particular, ASTER mapping results show that several of the dune sites display patterns such that less dense minerals typically have higher abundances near the center of the active and most evolved dunes in the field, while more dense minerals and glasses appear to be more abundant along the margins of the active dune fields.

Determining mineralogical variations of aeolian deposits using thermal infrared emissivity and linear deconvolution methods

Science.gov (United States)

Hubbard, Bernard E.; Hooper, Donald M.; Solano, Federico; Mars, John C.

2018-02-01

We apply linear deconvolution methods to derive mineral and glass proportions for eight field sample training sites at seven dune fields: (1) Algodones, California; (2) Big Dune, Nevada; (3) Bruneau, Idaho; (4) Great Kobuk Sand Dunes, Alaska; (5) Great Sand Dunes National Park and Preserve, Colorado; (6) Sunset Crater, Arizona; and (7) White Sands National Monument, New Mexico. These dune fields were chosen because they represent a wide range of mineral grain mixtures and allow us to gauge a better understanding of both compositional and sorting effects within terrestrial and extraterrestrial dune systems. We also use actual ASTER TIR emissivity imagery to map the spatial distribution of these minerals throughout the seven dune fields and evaluate the effects of degraded spectral resolution on the accuracy of mineral abundances retrieved. Our results show that hyperspectral data convolutions of our laboratory emissivity spectra outperformed multispectral data convolutions of the same data with respect to the mineral, glass and lithic abundances derived. Both the number and wavelength position of spectral bands greatly impacts the accuracy of linear deconvolution retrieval of feldspar proportions (e.g. K-feldspar vs. plagioclase) especially, as well as the detection of certain mafic and carbonate minerals. In particular, ASTER mapping results show that several of the dune sites display patterns such that less dense minerals typically have higher abundances near the center of the active and most evolved dunes in the field, while more dense minerals and glasses appear to be more abundant along the margins of the active dune fields.

The Karakum and Kyzylkum sand seas dynamics; mapping and palaeoclimatic interpretations

Science.gov (United States)

Maman, Shimrit; Blumberg, Dan G.; Tsoar, Haim; Porat, Naomi

2015-04-01

Sand seas are large basins in deserts that are mantled by wind-swept sand and that exhibit varying degrees of vegetation cover. Wilson (1973) was the first to globally map and classify sand seas. Beyond Wilson's maps, however, little research has been published regarding the Karakum and Kyzylkum sand seas of Central Asia. Wilson's maps delineate active ergs from inactive ergs based solely on precipitation. His assumption of annual average rainfall as a factor determining mobility vs. stability of sand seas is too simplistic and does not take into consideration other factors such as biogenic soil crusts and wind power, both of which are known to have major effects on the dynamics of sand dunes. Literature related to mapping and classifying the Central Asian ergs by remote sensing or sand sea classification state (stable/active) is lacking. Moreover, the palaeoclimatic significance of dunes in Central Asia is difficult to assess, as there has been few studies of dune stratigraphy and numerical ages are lacking. Optically stimulated luminescence (OSL) is a firm optical dating method that is used to determine the elapsed time since quartz grains were last exposed to sunlight, thus, their burial. Yet, absolute ages indicating mobilization and stabilization of these sands, are still inadequately known and are here under discussion. The broad concern of this research was to determine the dynamics of the Central Asian sand seas and study the palaeoclimatic changes that brought to their stabilization. As there are no reliable maps or aeolian discussion of these sands, establishment of a digital data base was initially conducted, focusing on identifying and mapping these sand seas. The vast area and inaccessibility make traditional mapping methods virtually impossible. A variety of space-borne imagery both optical and radar, with varying spectral and spatial resolutions was used. These images provided the basis for mapping sand distribution, dune forms, and vegetation cover

The Sources of Moisture in the Sand Dunes – The Example of the Western Sahara Dune Field

Directory of Open Access Journals (Sweden)

Żmudzka Elwira

2014-09-01

Full Text Available Climatic and meteorological conditions may limit the aeolian transport within barchans. An explanation of that issue was the main goal of the investigation held in Western Sahara dune fields located around Tarfaya and Laâyoune. Particular attention was paid to the factors causing the moisture content rising of the sand dune surface layer, which could influence the wind threshold shear velocity in the aeolian transport. The wetted surface layer of sand, when receiving moisture from precipitation or suspensions, reduces the aeolian transport, even in case of wind velocity above 4-5 m s-1. Fog and dew condensation does not affect the moisture of deeper sand layers, what occurs after rainfall.

Numerical simulation of seismic performance of the underground structure buried in the dense saturated sand

International Nuclear Information System (INIS)

Kawai, Tadashi

2006-01-01

The applicability of the advanced earthquake resistant performance verification method on reinforced concrete underground structures developed by CRIEPI was investigated for the structures which buried in the dry sand. For the advancement of the method in practical use, the applicability to the structures buried in the saturated ground is expected to be verified. In this study the applicability of the effective stress based soil modeling method in numerical analysis, which was proposed through the modification of the formerly developed model by CRIEPI, was verified through the non-linear dynamic numerical simulations of the large centrifuge tests conducted by using a model comprised of fully saturated sand and a aluminium duct type structure specially prepared for the measurement of the load acting on the structure surface with the soil-structure interaction. The magnitudes of the simulated loads and the resultant deformations of the structure were almost same as those of experiments. As a result it is confirmed that the performance verification method is useful for the structures buried in the saturated ground with using the proposed effective stress based ground modeling method. (author)

Possibilities of utilizing used moulding and core sands by microwave treatment

Directory of Open Access Journals (Sweden)

K. Granat

2011-01-01

Full Text Available The paper presents a semi-industrial reactor designed for microwave utilization of waste moulds and cores made of moulding sandsprepared in furane resin technology. It was found that a possibility exists of effective incinerating this way prepared residues of coresseparated from moulding sands or waste moulds left after casting. The preliminary tests evidenced that microwave heating is an effectiveway of disposing waste moulding sands and the applied apparatus permits effective control of the microwave heating process. The special structure permitting rotations of charge material and proper selection of the generators working cycles guarantee significant speeding-up the process and its full stabilisation. Application of microwave heating for utilization of waste moulds and cores containing synthetic resins as binders ensures significant and measurable economical benefits resulting from shorter process time.

On Foundation Improvement By Sand Replacement | Abam | Global ...

African Journals Online (AJOL)

This paper describes a simple foundation improvement method involving the replacement of poor foundation bearing soils with sand and the resultant improvement in bearing capacity and the minimization of settlement at the site of a large storage tank. Minimum thickness of sand replacement for various foundation loads ...

Interaction of petroleum mulching, vegetation restoration and dust fallout on the conditions of sand dunes in southwest of Iran

Science.gov (United States)

Azoogh, Liela; Khalili moghadam, Bijan; Jafari, Siroos

2018-06-01

In the past half-century, petroleum mulching-biological fixation (PM-BF) practices have been employed to stabilize sand dunes in Iran. However, the effects of PM-BF practices on the attributes of sand dunes and the dispersion of heavy metals of mulch have been poorly understood. To this end, three regions treated with PM-BF for 5, 20, and 40 years and a control region with no PM-BF were studied. Samples of soil properties were taken at the depths of 0-10 cm and 10-50 cm, with three replications, in Khuzestan Province. The results showed that PM-BF practices promoted the restoration of vegetation cover in the sand dunes. In addition, these practices increased the deposition of dust particles, gradually increasing the magnitudes of palygorskite and smectite clays over time. The interactions between dust deposition and PM-BF practices significantly altered the chemical and physical properties of the dunes. PM-BF practices increased soil organic matter (184-287%), cation exchangeable capacity (142-209%), electrical conductivity (144-493%), clay content (134-196%), and penetration resistance (107-170%) compared to the region with no PM-BF practices. Furthermore, petroleum mulching significantly increased the amount of Ni (1.19%), Cd (1.55%), Pb (1.08%), Cu (1.34%), Zn (1.38%), Mn (1.66%), and Fe (1.15%). However, in the long term, these elements will probably leach linearly as a consequence of an increase in organic matter and soil salinity in the light texture of sand dunes.

Application of RFLP-PCR-Based Identification for Sand Fly Surveillance in an Area Endemic for Kala-Azar in Mymensingh, Bangladesh

Directory of Open Access Journals (Sweden)

Mohammad Shafiul Alam

2012-01-01

Full Text Available Mymensingh is the most endemic district for kala-azar in Bangladesh. Phlebotomus argentipes remains the only known vector although a number of sand fly species are prevalent in this area. Genotyping of sand flies distributed in a VL endemic area was developed by a PCR and restriction-fragment-length polymorphism (RFLP of 18S rRNA gene of sand fly species. Using the RFLP-PCR analysis with AfaI and HinfI restriction enzymes, P. argentipes, P. papatasi, and Sergentomyia species could be identified. Among 1,055 female sand flies successfully analyzed for the species identification individually, 64.4% flies was classified as Sergentomyia species, whereas 35.6% was identified as P. argentipes and no P. papatasi was found. Although infection of Leishmania within the sand flies was individually examined targeting leishmanial minicircle DNA, none of the 1,055 sand flies examined were positive for Leishmania infection. The RFLP-PCR could be useful tools for taxonomic identification and Leishmania infection monitoring in endemic areas of Bangladesh.

Ask Dr. Sue: Tree Climbing and Care of Sand Play Areas.

Science.gov (United States)

Aronson, Susan S.

1993-01-01

Discusses safety aspects of tree climbing and the use of sand in outdoor play areas at day care centers. Specifies ways to prune trees so that they are unclimbable and methods for maintaining sand areas. Includes a recipe for sand disinfectant. (MDM)

Advanced testing and characterization of shear modulus and deformation characteristics of oil sand materials

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2014-09-01

Full Text Available and Pressures,” Can. Geotech. J., Vol. 24, 1987, pp. 1–10. [5] Samieh, A.M. and Wong, R.C.K., “Deformation of Athabasca Oil Sand in Triaxial Compression Tests at Low Effective Stresses under Varying Boundary Conditions,” Can. Geotech. J., Vol.34, 1997, pp.... 985– 990. [6] Samieh, A.M. and Wong, R.C.K., “Modeling the Responses of Athabasca Oil Sand in Triaxial Compression Tests at Low Pressure,” Can. Geotech. J., Vol. 35, 1998, pp. 395–406. [7] AASHTO Standard T265, 2009, “Laboratory Determination...

Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources

Energy Technology Data Exchange (ETDEWEB)

Spinti, Jennifer [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Birgenheier, Lauren [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Deo, Milind [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Facelli, Julio [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Hradisky, Michal [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Kelly, Kerry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Miller, Jan [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); McLennan, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ring, Terry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ruple, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Uchitel, Kirsten [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States)

2015-09-30

(March, 2012); Conjunctive Surface and Groundwater Management in Utah: Implications for Oil Shale and Oil Sands Development (May, 2012); Development of CFD-Based Simulation Tools for In Situ Thermal Processing of Oil Shale/Sands (February, 2012); Core-Based Integrated Sedimentologic, Stratigraphic, and Geochemical Analysis of the Oil Shale Bearing Green River Formation, Uinta Basin, Utah (April, 2011); Atomistic Modeling of Oil Shale Kerogens and Asphaltenes Along with their Interactions with the Inorganic Mineral Matrix (April, 2011); Pore Scale Analysis of Oil Shale/Sands Pyrolysis (March, 2011); Land and Resource Management Issues Relevant to Deploying In-Situ Thermal Technologies (January, 2011); Policy Analysis of Produced Water Issues Associated with In-Situ Thermal Technologies (January, 2011); and Policy Analysis of Water Availability and Use Issues for Domestic Oil Shale and Oil Sands Development (March, 2010)

Research for the development of the crushed sand (II)

Energy Technology Data Exchange (ETDEWEB)

Park, Chul Whan; Kang, Sun Duck; Min, Jeong Sik; Synn, Joong Ho; Park, Chan [Korea Institute of Geology Mining and Materials, Taejon (Korea)

1998-12-01

The sand obtained from river is not sufficient in amount for the demand of construction industry. The production of sand from sea and mountain is rapidly increasing for the substitution of the river sand. The industry of the crushed sand has recently been bricked for the above. Crushing, classification and dewatering are the main processes in the crushed sand production. This report concentrates the improvement of classification technology and the quality of ready mixed concrete. Air separator with testing size for the classification in the process of dry system was developed by the Yeung Nam university. This plant has the excellent efficiency for the collection of fine powder, but needs the improvement for separating function. The collection efficiency of the testing size air separator is reached to 99% in the condition of high revolution and low feeding speed. The classification efficiency is checked about 50% maximum in the condition of 200 rpm and dry sample. Energy saving test was carried out in the production process of the dry system with the rock samples of 14-17% of water content. The classification efficiency for dewatering sample passed the heating process was analysed 91.5%. But that for high water content sample skipped the heating process was analysed more or less 77%. Even though the heating process causes the classification efficiency being high, the energy consumption can also cause the price of the crushed sand high. Water content of sample as the effective element for the optimization of classification efficiency and energy saving should be studied next year. The quality of crushed sand in the mixing design. The test was carried out with the various content in mixing, the strength of ready mixed concrete has the maximum for the mould with 50-60% content of crushed sand. This strength is higher by 5-30% than 30% content and by 20-32% than 0% content, which means that the industry has the possibility of progress. (author). 10 refs., 31 tabs., 49

Alberta Oil Sands Equity annual report, 1991-92. Partnership and progress in Alberta's oil sands development

International Nuclear Information System (INIS)

1992-01-01

Alberta Oil Sands Equity (AOSE) manages the Alberta government's equity investments in oil sands and heavy oil projects. AOSE is a 16.74% participant in the Syncrude Project, a 10% participant in the OSLO (Other Six Leases Operation) Commercial Project and the OSLO New Ventures project, and a 24.17% participant in the Lloydminster Bi-Provincial Upgrader. Syncrude produces over 11% of Canadian crude oil requirements, and AOSE's share yielded $43.3 million profit for 1991/92, down significantly from the $82.1 million the previous year due to lower oil prices. The OSLO Commercial Project is a proposed commercial oil sands plant with a mine site and extraction plant to be located north of Fort McMurray, and an upgrading facility to be situated north of Edmonton. Work on this project was suspended in early 1992. The OSLO New Ventures project will handle the exploration and development of the remaining five oil sands leases plus the southern portion of Lease 31. As of March 31, 1992, the project owners were considering a commercial demonstration project utilizing dredging and cold-water extraction processes. Two of the owners are unable to provide funding and discussions are under way to resolve the matter and move the program forward. The Lloydminster Bi-Provincial Upgrader was nearly 90% complete in March 1992 and full startup is expected in November 1992; engineering work was completed in March 1991. The upgrader will increase the value of heavy crude oil and thereby increase its demand. 4 figs., 4 tabs

Effect of crushed sand on mortar and concrete rheology

Directory of Open Access Journals (Sweden)

Cabrera, O. A.

2011-09-01

Full Text Available This article describes an experimental study conducted on fresh mortars and concretes made with crushed sand. The aim of this research was to assess the effect of aggregate particle shape and surface texture as well as dust content on mortar and concrete rheology. The experimental programme also addressed the impact of angular grains on chemical admixture performance and concrete bleeding. The findings showed that the use of crushed sand induces rheological behaviour that differs from the behaviour observed in natural sand and that superplasticisers can improve this behaviour considerably.

En el presente trabajo se plantea un estudio experimental del estado fresco de morteros y hormigones con arenas de machaqueo, orientado a la evaluación de la incidencia de la forma y textura superficial de los granos del árido fino y del contenido de polvo sobre la reología de las mezclas. El programa experimental comprendió el estudio del estado fresco de hormigones con arenas con partículas angulares, la influencia de este tipo de partículas sobre la efectividad de los aditivos químicos y la evaluación de la influencia de las características físicas del árido fino sobre la exudación. Los resultados muestran que el empleo de arenas de machaqueo provoca un comportamiento reológico diferente al de hormigones con arenas naturales, y que el efecto de los aditivos superfluidificantes mejora notablemente este comportamiento.

CFD evaluation of erosion rate around a bridge near a sand dune

Science.gov (United States)

He, Wei; Huang, Ning; Dun, Hongchao; Wang, Wenbo

2017-04-01

This study performs a series of simulations through solving the Navier-Stokes equations and the RNG k-ε turbulence model to investigate the wind erosion rates around a bridge in a desert area with sand dunes. The digital elevation model of sand dunes and the bridge model are obtained respectively from hypsographic map and construction drawings. Through combining them into the CFD software of Fluent the simulation zone was formed. The data of wind speed obtained from field observation is fitted into a logarithm format, which was imported into Fluent model as a inlet wind speed condition. Then, the effect of Dun-Go railway on wind-blown sand movement of the neighbouring environment is simulated. The results exhibit that affected by both the sand dune and bridge, the flow field is in a complex condition. It is also shown that the bridge in upstream of the sand dune will not increase the sand transport rate intensively, but change both wind velocity gradient and turbulence kinetic energy over surface of sand dune. On the other hand, when the bridge is built downstream the sand dune, simulation results show that sand deposition rate would be decreased in reference region downstream the pier.

The oil sands: A new energy vision for Canada

International Nuclear Information System (INIS)

1995-01-01

Canada's oil sands deposits were considered to offer huge potential for wealth generation and enduring social benefits. This report showed that putting in action the plan developed by the National Task Force on Oil Sands Strategies would help unlock this potential and realize the benefits; the forecast called for a doubling or tripling of oil sands production over the next 25 years. The plan should also predicted an increase in investments in oil sands since the fiscal regime would be stable and the product would be in increasing demand. New capital investment should generate significant environmental, social and economic benefits. The real outcome would be increased national prosperity, since further growth in investment would translate into thousands of skilled jobs across Canada, expansion of government revenues, and improvements to Canada's trade balance. 1 ill

Oil sands: Strategies for future development - An overview

International Nuclear Information System (INIS)

Yildirim, E.

1995-01-01

The Alberta Chamber of Resources developed a Task Force in 1993 to promote oil sands development, and to identify and publicize the social and economic benefits of oil sands operations. Formation, mission of the National Task Force, impediments and opportunities for development were summarized. Attributes of oil sands, benefits of their development, impediments to development, strategic development and potential growth scenarios were discussed. Cooperation between government and industry was deemed essential. Recommendations included development of a bitumen pipeline network, provision of incentives to encourage development, encouragement of risk and reward sharing between bitumen producers and up graders, and diversification of products and by-products. 7 figs., 12 refs