Aumento da aeração nasal após remoção de hábitos de sucção e terapia miofuncional

OpenAIRE

Degan,Viviane Veroni; Puppin-Rontani,Regina Maria

2007-01-01

OBJETIVO: avaliar os efeitos da associação entre a remoção de hábitos de sucção e a Terapia Miofuncional Orofacial na ampliação da aeração nasal. MÉTODOS: vinte crianças na faixa de etária de quatro anos a quatro anos e oito meses foram distribuídas em dois grupos denominados de: Grupo REM (submetido apenas à remoção de hábitos) e Grupo TMF (submetido à remoção de hábitos e posteriormente à Terapia Miofuncional Orofacial). O fluxo de ar expirado pelas narinas foi registrado por meio do espelh...

The genesis solar-wind sample return mission

International Nuclear Information System (INIS)

Wiens, Roger C.

2009-01-01

The compositions of the Earth's crust and mantle, and those of the Moon and Mars, are relatively well known both isotopically and elementally. The same is true of our knowledge of the asteroid belt composition, based on meteorite analyses. Remote measurements of Venus, the Jovian atmosphere, and the outer planet moons, have provided some estimates of their compositions. The Sun constitutes a large majority, > 99%, of all the matter in the solar system. The elemental composition of the photosphere, the visible 'surface' of the Sun, is constrained by absorption lines produced by particles above the surface. Abundances for many elements are reported to the ±10 or 20% accuracy level. However, the abundances of other important elements, such as neon, cannot be determined in this way due to a relative lack of atomic states at low excitation energies. Additionally and most importantly, the isotopic composition of the Sun cannot be determined astronomically except for a few species which form molecules above sunspots, and estimates derived from these sources lack the accuracy desired for comparison with meteoritic and planetary surface samples measured on the Earth. The solar wind spreads a sample of solar particles throughout the heliosphere, though the sample is very rarified: collecting a nanogram of oxygen, the third most abundant element, in a square centimeter cross section at the Earth's distance from the Sun takes five years. Nevertheless, foil collectors exposed to the solar wind for periods of hours on the surface of the Moon during the Apollo missions were used to determine the helium and neon solar-wind compositions sufficiently to show that the Earth's atmospheric neon was significantly evolved relative to the Sun. Spacecraft instruments developed subsequently have provided many insights into the composition of the solar wind, mostly in terms of elemental composition. These instruments have the advantage of observing a number of parameters simultaneously

Simulation of atmospheric CO2 over Europe and western Siberia using the regional scale model REMO

International Nuclear Information System (INIS)

Chevillard, A.; Ciais, P.; Lafont, S.

2002-01-01

The spatial distribution and the temporal variability of atmospheric CO 2 over Europe and western Siberia are investigated using the regional atmospheric model, REMO. The model, of typical horizontal resolution 50 km, is part of a nested modelling framework that has been established as a concerted action during the EUROSIBERIAN CARBONFLUX project. In REMO, the transport of CO 2 is simulated together with climate variables, which offers the possibility of calculating at each time step the land atmosphere CO 2 fluxes as driven by the modelled meteorology. The uptake of CO 2 by photosynthesis is calculated using a light use efficiency formulation, where the absorbed photosynthetically active solar radiation is inferred from satellite measurements. The release of CO 2 from plant and soil respiration is driven by the simulated climate and assumed to be in equilibrium with photosynthesis over the course of one year. Fossil CO 2 emissions and air-sea fluxes within the model domain are prescribed, whereas the influence of sources outside the model domain is computed from as a boundary condition CO 2 fields determined a global transport model. The modelling results are compared against pointwise eddy covariance fluxes, and against atmospheric CO 2 records. We show that a necessary condition to simulate realistically the variability of atmospheric CO 2 over continental Europe is to account for the diurnal cycle of biospheric exchange. Overall, for the study period of July 1998, REMO realistically simulates the short-term variability of fluxes and of atmospheric mixing ratios. However, the mean CO 2 gradients from western Europe to western Siberia are not correctly reproduced. This latter deficiency points out the key role of boundary conditions in a limited-area model, as well as the need for using more realistic geographic mean patterns of biospheric carbon fluxes

San Remo Konferansı’nda İngiltere’nin Ermeni Politikası (18-26 Nisan 1920 Britain’s Armenian Policy on San Remo Conference (18-26 April 1920

Directory of Open Access Journals (Sweden)

Evren KÜÇÜK

2012-09-01

Full Text Available Between 18-26 April 1920, The Allied Powers came together in San Remo, Italy to impose their demands on the Ottoman Empire. During these negotiations called San Remo Conference, Boghos Nubar Pasha and Avetis Ahoranian representing Armenia went on to put forward territorial claims on the Ottoman Empire. In order to materialise these demands, a mandatory power was needed to defend, develop and finance the Armenian existence. This situation resulted in Britain’s diplomatic manoeuvre. As the Mesopotamia region was also particularly important for Britain, the mandatory role in Anatolia was to be given to the United States of America. In case the USA denied the role, the Turkish-Armenian border was proposed to be resolved under the arbitration of the United States President Wilson. In San Remo, however, presidents of other states enounced that they were troubled with the responsibility of undertaking the mandatory of Armenia and would not be providing any financial or military aid as well. These demographically baseless and impracticable demands could not be expected to be approved by the movement led by Mustafa Kemal Pasha. Moreover, the military triumphs in the Eastern Front resulted in the failure of Britain’s Armenian policy and by-passed United States President Wilson’s 22 November 1920 dated report about the Turkish-Armenian border, prepared according to 89th clause of the Treaty of Sevres as well. On one hand, this war of survival led to the break up of the Allied Powers in the end and resulted in even Italy and France's backing the national struggle movement. On the other hand, it brought an end to both Lloyd George Government and Ottoman Imperialism. Müttefik Devletler, Osmanlı Devleti’ne isteklerini kabul ettirebilmek için 18-26 Nisan 1920 tarihleri arasında İtalya’nın San Remo şehrinde toplanmışlardır. San Remo Konferansı olarak adlandırılan bu görüşmelerde Ermenileri temsilen Boghos Nubar Paşa ile Avetis

Avaliação do desempenho de canal gramado na remoção de material suspenso em escoamento superficial pluvial

Directory of Open Access Journals (Sweden)

Rodrigo Braga Moruzzi

Full Text Available RESUMO Neste trabalho, buscou-se avaliar o desempenho de canal gramado na remoção de material suspenso presente em escoamento superficial em unidade construída em escala real. Para tal, foram investigadas diferentes concentrações iniciais de material particulado, o qual foi descarregado por meio de chuvas simuladas em canal de 100 m de extensão e declividade de 2%. As medidas de material particulado foram feitas mediante a análise de sólidos suspensos totais (SST em diferentes posições ao longo do canal. Os hidrogramas de descarregamento e as lâminas de água no canal foram monitorados durante a passagem da onda de cheia. Avaliaram-se as frações removidas para cada evento isolado e também em conjunto, por intermédio da interpolação por krigagem. Remoções da ordem de 50% foram obtidas para a posição de 50 m do canal gramado e de 70% para a posição de 80 m. Os resultados mostraram que a remoção de material particulado é fortemente dependente da extensão do canal e que os aspectos dinâmicos decorrentes da passagem da onda de cheia influenciam no processo.

The effects of disjunct sampling and averaging time on maximum mean wind speeds

DEFF Research Database (Denmark)

Larsén, Xiaoli Guo; Mann, J.

2006-01-01

Conventionally, the 50-year wind is calculated on basis of the annual maxima of consecutive 10-min averages. Very often, however, the averages are saved with a temporal spacing of several hours. We call it disjunct sampling. It may also happen that the wind speeds are averaged over a longer time...

Contribuição para o estudo de sistemas de tratamento de água para abastecimento associados à remoção de compostos farmacêuticos

OpenAIRE

Cid, Joana Ferraz Leal de Sobral

2011-01-01

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia do Ambiente, perfil Engenharia Sanitária Este trabalho pretende contribuir para o estudo de sistemas de tratamento de água para abastecimento associados à remoção de compostos farmacêuticos. Assim, para melhor compreender a importância da remoção dos compostos farmacêuticos da água para abastecimento surge uma abordagem sobre a presença dos compostos...

Avaliação da eficiência da aplicação de coagulante orgânico em chorume para remoção de carga orgânica e nutrientes

Directory of Open Access Journals (Sweden)

Daniel Kuhn

2015-07-01

Full Text Available A proteção de mananciais e a preocupação com a escassez de água potável no mundo implicam, cada vez mais, na busca de alternativas que visem melhorar a eficiência dos sistemas de tratamento dos mais variados efluentes, difundindo parâmetros de operação. No caso dos lixiviados, ou chorume, de aterros sanitários, são consideradas variáveis importantes a idade de operação do aterro e as diferenças sazonais, principalmente em relação às condições climáticas e as peculiaridades de cada região, sendo que, dessa forma, não há um padrão para a operação de estações de tratamento, onde deve ser estudado caso a caso para um tratamento mais eficiente. Este estudo teve o objetivo de avaliar a eficiência do uso de coagulante orgânico no tratamento de chorume em jar-test, para posterior aplicação na planta da estação de tratamento, na etapa de decantação, avaliando a eficiência de remoção da demanda química de oxigênio (DQO, demanda biológica de oxigênio (DBO, nitrogênio total, turbidez além de avaliação do pH. Para DQO, obteve-se um resultado médio de 30% de remoção, DBO 26% de remoção e para turbidez 84% de remoção. Para o parâmetro de nitrogênio total não houve eficiência de remoção. Conclui-se que essa etapa de coagulação pode ser acrescentada ao processo, com o propósito de remoção de carga orgânica, atuando como uma parte auxiliar no processo de tratamento.

Remoção da cor no tratamento combinado de lixiviado de aterro sanitário e esgoto doméstico via processo PACT®

Directory of Open Access Journals (Sweden)

Ángel Santiago Fernández Bou

2018-03-01

Full Text Available RESUMO Misturas diferentes de lixiviado de aterro sanitário e esgoto doméstico foram aplicadas em 16 reatores em batelada usando o processo PACT® (lodos ativados com adição de carvão ativado em pó - CAP. O objetivo do trabalho foi representar a remoção de cor utilizando dois ajustes matemáticos: o primeiro combinou as variáveis concentração de CAP (0 a 6 g.L-1 e mistura lixiviado/esgoto (0 a 10%, em volume; e o segundo, a concentração de CAP e a cor da mistura (276 a 1.199 uH. A metodologia de superfície de resposta (MSR foi escolhida para representar a resposta dos ajustes. Os resultados indicaram que, conforme a concentração de lixiviado aumentou até 5%, a adição de CAP resultou em um maior percentual de remoção de cor. No entanto, para a mistura com 10% de lixiviado, os reatores perderam eficácia, com exceção do reator com 6 g.L-1 de CAP, que apresentou os melhores resultados de remoção de cor.

Avaliação da nanofiltração e da osmose inversa na remoção de carbofurano em águas de abastecimento

Directory of Open Access Journals (Sweden)

Marcelo Zawadzki Bueno

Full Text Available RESUMO: A complexidade físico-química de micropoluentes, como os defensivos agrícolas, exige o uso de tecnologias avançadas de tratamento de água para abastecimento. O objetivo deste estudo foi avaliar a remoção de carbofurano em nível de bancada (batelada utilizando membranas comerciais de nanofiltração (NF90 - DowFilmtec (r e osmose inversa (HR - Koch Membrane Systems(r . Nos experimentos foi avaliada a influência da qualidade da matriz de alimentação (água ultrapura, bruta e pré-tratada contendo carbofurano (50 µgL-1, e da pressão de operação (8 e 15 bar para a NF90 e 15 e 30 bar para a HR. Para a NF90, com a matriz de água ultrapura, as eficiências de remoção foram inferiores (89,8%, porém o fluxo permeado foi superior (132,1 Lm-2h-1 àquelas obtidas com a matriz de água bruta (98,4% - 94,7 Lm-2h-1 e água pré-tratada (95,2% - 95,3 Lm-2h-1 para a pressão de 15 bar. Para a membrana HR, remoções relativamente superiores foram observadas para a pressão de 30 bar para as três matrizes, com a água bruta apresentando os melhores resultados (99,7% - 49,7 Lm-2h-1. Concluiu-se, portanto, que o pré-tratamento da água bruta não acarretou diferença significativa na remoção do carbofurano e não influenciou no fluxo de permeado de acordo com a metodologia adotada (baixo tempo de separação em batelada com recirculação.

Development of Chemical and Mechanical Cleaning Procedures for Genesis Solar Wind Samples

Science.gov (United States)

Schmeling, M.; Jurewicz, A. J. G.; Gonzalez, C.; Allums, K. K.; Allton, J. H.

2018-01-01

The Genesis mission was the only mission returning pristine solar material to Earth since the Apollo program. Unfortunately, the return of the spacecraft on September 8, 2004 resulted in a crash landing shattering the solar wind collectors into smaller fragments and exposing them to desert soil and other debris. Thorough surface cleaning is required for almost all fragments to allow for subsequent analysis of solar wind material embedded within. However, each collector fragment calls for an individual cleaning approach, as contamination not only varies by collector material but also by sample itself.

Materiais a base de estruturas carbonáceas para a remoção de ácidos húmicos em soluções aquosas através da adsorção e oxidação

OpenAIRE

Eustáquio, Hugo Mozer Barros

2015-01-01

O presente estudo aborda a utilização de carvão ativado comercial na remoção de ácidos húmicos em meio aquoso. O objetivo principal é desenvolver e caracterizar materiais carbonáceos visando aplicações de remoção de ácidos húmicos em meio aquoso por processos de adsorção e oxidação. Testes de remoção do poluente foram desenvolvidos com a utilização do carvão comercial, carvão modificado a partir de tratamentos ácidos e compósito confeccionado com a impregnação de ferro no carvão. Espumas de c...

Hierarquização da eficiência de remoção de cianotoxinas por meio de adsorção em carvão ativado granular

OpenAIRE

Maria Natália Costa e Silva; Rui de Oliveira; Beatriz Susana Ovruski Ceballos; Alaine Brito Guerra; Sérgio Francisco de Aquino; Marcelo Libânio

2017-01-01

RESUMO O trabalho objetivou avaliar a remoção concomitante de duas cianotoxinas - microcistina-LR e saxitoxina-STX - por meio da adsorção em carvão ativado granular. Em primeira etapa, três carvões de granulometrias distintas, dois de coco de dendê e um mineral, foram avaliados na adsorção de microcistina-LR em água destilada e tratada com concentrações de 3,9 a 9,4 ug.L-1. O carvão de coco de dendê de menor granulometria apresentou desempenho mais uniforme, tanto no que tange à remoção (%) d...

Avaliação do potencial de compostos naturais (argila, turfa e carvão na remoção de chumbo e toxicidade de um efluente industrial

Directory of Open Access Journals (Sweden)

Richard Clayton Tomasella

2015-06-01

Full Text Available Métodos de tratamento avançado utilizando-se de materiais adsorventes alternativos podem substituir ou complementar tratamentos convencionais existentes, auxiliando na remoção de substâncias tóxicas provindas de diversos processos industriais. Espectrometria e testes biológicos (toxicidade aguda e crônica auxiliam no monitoramento dos rejeitos industriais, avaliando a eficiência desses sistemas alternativos de tratamento de efluentes. O trabalho objetivou promover a redução da concentração do chumbo (Pb e da toxicidade de um efluente industrial utilizando o potencial de compostos naturais (argilominerais e turfa e do carvão ativado (controle como adsorventes em ensaios em batelada. O carvão ativado permitiu remover 99,4% do Pb no efluente (15 min, e para os demais adsorventes a remoção ocorreu progressivamente até 24 horas, resultando em eficiências de remoção de 88,0% (argila do Vale do Paraíba - VP, 73,6% (argila de Ajapí - A e 63,5% (turfa. A toxicidade aguda foi completamente removida com a utilização do carvão ativado, enquanto eficiências de remoção maiores do que 50% foram obtidas utilizando compostos naturais. Efeito tóxico significativo não foi observado após o tratamento com o carvão ativado e argila VP com relação à toxicidade crônica. Os resultados indicam a possibilidade de utilização da argila VP como adsorvente de baixo custo comercial em métodos de tratamento avançado.

Quality assessment of water cycle parameters in REMO by radar-lidar synergy

Directory of Open Access Journals (Sweden)

B. Hennemuth

2008-01-01

Full Text Available A comparison study of water cycle parameters derived from ground-based remote-sensing instruments and from the regional model REMO is presented. Observational data sets were collected during three measuring campaigns in summer/autumn 2003 and 2004 at Richard Aßmann Observatory, Lindenberg, Germany. The remote sensing instruments which were used are differential absorption lidar, Doppler lidar, ceilometer, cloud radar, and micro rain radar for the derivation of humidity profiles, ABL height, water vapour flux profiles, cloud parameters, and rain rate. Additionally, surface latent and sensible heat flux and soil moisture were measured. Error ranges and representativity of the data are discussed. For comparisons the regional model REMO was run for all measuring periods with a horizontal resolution of 18 km and 33 vertical levels. Parameter output was every hour. The measured data were transformed to the vertical model grid and averaged in time in order to better match with gridbox model values. The comparisons show that the atmospheric boundary layer is not adequately simulated, on most days it is too shallow and too moist. This is found to be caused by a wrong partitioning of energy at the surface, particularly a too large latent heat flux. The reason is obviously an overestimation of soil moisture during drying periods by the one-layer scheme in the model. The profiles of water vapour transport within the ABL appear to be realistically simulated. The comparison of cloud cover reveals an underestimation of low-level and mid-level clouds by the model, whereas the comparison of high-level clouds is hampered by the inability of the cloud radar to see cirrus clouds above 10 km. Simulated ABL clouds apparently have a too low cloud base, and the vertical extent is underestimated. The ice water content of clouds agree in model and observation whereas the liquid water content is unsufficiently derived from cloud radar reflectivity in the present study

Shorlist Masterplan Wind. Evaluation of the sampling grid of the year-round ichthyoplankton survey

NARCIS (Netherlands)

Bolle, L.J.; Beek, van J.K.L.

2011-01-01

Within the research programme 'Shortlist Masterplan Wind' a year-round ichthyoplankton survey is being carried out. The sampling area is based on known spawning concentrations and prevailing currents.

Wireless AE Event and Environmental Monitoring for Wind Turbine Blades at Low Sampling Rates

Science.gov (United States)

Bouzid, Omar M.; Tian, Gui Y.; Cumanan, K.; Neasham, J.

Integration of acoustic wireless technology in structural health monitoring (SHM) applications introduces new challenges due to requirements of high sampling rates, additional communication bandwidth, memory space, and power resources. In order to circumvent these challenges, this chapter proposes a novel solution through building a wireless SHM technique in conjunction with acoustic emission (AE) with field deployment on the structure of a wind turbine. This solution requires a low sampling rate which is lower than the Nyquist rate. In addition, features extracted from aliased AE signals instead of reconstructing the original signals on-board the wireless nodes are exploited to monitor AE events, such as wind, rain, strong hail, and bird strike in different environmental conditions in conjunction with artificial AE sources. Time feature extraction algorithm, in addition to the principal component analysis (PCA) method, is used to extract and classify the relevant information, which in turn is used to classify or recognise a testing condition that is represented by the response signals. This proposed novel technique yields a significant data reduction during the monitoring process of wind turbine blades.

Concepción, Desarrollo y Avances en el Control de Navegación de Robots Submarinos Paralelos: El Robot Remo-I

Directory of Open Access Journals (Sweden)

César Álvarez

2009-07-01

Full Text Available Resumen: El robot REMO I es un vehículo submarino operado remotamente (ROV, que tiene como cuerpo principal, una estructura paralela de Stewart – Gough, que le permite variar su geometría para realizar maniobras de navegación con gran flexibilidad con solo modificar la orientación y el desplazamiento de un único impulsor situado en la parte trasera. Como consecuencia, el robot puede describir trayectorias complejas para llegar a lugares de difícil acceso dentro del agua. En este trabajo se presenta una breve descripción mecánica del REMO I, su sistema de instrumentación y control, y las estrategias a utilizar para la arquitectura de control que se emplea en el control de lastrado y la navegación. Palabras clave: Vehículos submarinos, robots submarinos, estructura paralela, plataformas Stewart – Gough, ROV, AUV

Test Plan for Rotary Mode Core Sample Truck Grapple Hoist Level Wind System

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

A Grapple Hoist Assembly is currently used on the Rotary Mode Core Sampling Trucks (RMCSTs) to actuate the sampler and retrieve the pintle rod during sampling operations. The hoist assembly includes a driven drum approximately two inches wide and six inches in diameter that rotates to pay out or reel in the 5/32-in. cable The current Grapple Hoist Assembly, detailed on drawing H-2-690057, is prone to ''bird nesting'' the cable on the drum. ''Bird nesting'' is a condition in which the cable does not wind onto the drum in a uniformly layered manner, but winds in a random fashion where the cable essentially ''piles up'' inappropriately on the drum and, on some occasions, winds on the drum drive shaft. A system to help control this ''bird nesting'' problem has been designed as an addition to the existing components of the Grapple Hoist Assembly. The new design consists of a mechanism that is timed with, and driven by, the shaft that drives the drum. This mechanism traverses back and forth across the width of the drum to lay the cable on the drum in a uniformly layered manner. This test plan establishes the acceptance criteria, test procedure and test conditions It also describes the test apparatus necessary to verify the adequacy of the level wind system design. The test is defined as qualification testing (LMHC 1999b) and as such will be performed at conditions beyond the parameters that the Grapple Hoist Assembly is allowed to operate by the Safety Equipment List (SEL)(LMHC 1998)

Test Plan for Rotary Mode Core Sample Truck Grapple Hoist Level Wind System

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

A Grapple Hoist Assembly is currently used on the Rotary Mode Core Sampling Trucks (RMCSTs) to actuate the sampler and retrieve the pintle rod during sampling operations. The hoist assembly includes a driven drum approximately two inches wide and six inches in diameter that rotates to pay out or reel in the 5/32-in. cable. The current Grapple Hoist Assembly, detailed on drawing H-2-690057, is prone to ''bird nesting'' the cable on the drum. ''Bird nesting'' is a condition in which the cable does not wind onto the drum in a uniformly layered manner, but winds in a random fashion where the cable essentially ''piles up'' inappropriately on the drum and, on some occasions, winds on the drum drive shaft. A system to help control this ''bird nesting'' problem has been designed as an addition to the existing components of the Grapple Hoist Assembly. The new design consists of a mechanism that is timed with, and driven by, the shaft that drives the drum. This mechanism traverses back and forth across the width of the drum to lay the cable on the drum in a uniformly layered manner. This test plan establishes the acceptance criteria, test procedure and test conditions. It also describes the test apparatus necessary to verify the adequacy of the level wind system design. The test is defined as qualification testing (LMHC 1999b) and as such will be performed at conditions beyond the parameters that the Grapple Hoist Assembly is allowed to operate by the Safety Equipment List

Uso de biomassa seca de aguapé (Eichornia crassipes visando à remoção de metais pesados de soluções contaminadas - DOI: 10.4025/actascitechnol.v31i1.3166

Directory of Open Access Journals (Sweden)

Affonso Celso Gonçalves Júnior

2009-04-01

Full Text Available O presente trabalho avaliou a eficiência da biomassa seca de aguapé (Eichornia crassipes na remoção dos metais pesados cádmio (Cd, chumbo (Pb, cromo (Cr, cobre (Cu, zinco (Zn e níquel (Ni de soluções preparadas com estes metais. O delineamento utilizado foi inteiramente casualizado, com cinco tratamentos (soluções com diferentes concentrações dos metais pesados e quatro repetições. A biomassa seca permaneceu nas soluções dos tratamentos por um período de 48h, e nos intervalos de 1; 2; 3; 6; 12; 24; 36 e 48h após a instalação do experimento, coletaram-se alíquotas de cada tratamento, determinando-se a maior remoção de cada metal pesado pela biomassa seca do aguapé. Foi realizada digestão nitroperclórica na biomassa seca e determinação dos teores dos metais na biomassa e nas alíquotas por espectrometria de absorção atômica, modalidade chama. Para os metais Cd, Pb, Cr, Cu e Zn ocorreu remoção significativa pela massa seca do aguapé nos diferentes tratamentos, enquanto para o Ni não foi encontrada diferença significativa. Dessa forma, conclui-se que a biomassa seca produzida, a partir do aguapé Eichornia crassipes, é um excelente material para a remoção, tanto em pequena como em grande escala, de corpos hídricos contaminados com metais pesados.

Remoção de matéria orgânica do esgoto em solo de wetland construído

Directory of Open Access Journals (Sweden)

Selma Cristina da Silva

2015-12-01

Full Text Available RESUMO Nos sistemas wetlands construídos os meios suportes tradicionalmente utilizados são areia grossa, cascalho, pedregulho e brita. Nesta pesquisa, foi utilizado o solo natural (Latossolo Vermelho-Amarelo misturado com areia média, plantado (wetlands construídos com arroz irrigado (Oryza sativa L. ou não (controles. O objetivo foi avaliar a remoção de DBO dos esgotos domésticos pelos processos de imobilização do carbono da biomassa microbiana e da respiração basal (atividade microbiana. Foram utilizados três sistemas operando com taxas de aplicação hidráulica de 4, 8 e 15 cm.d1. Cada sistema apresentava três unidades wetlands construídos e três controles, as quais eram alimentadas com esgotos para tratamento, por fluxo vertical em regime não saturado, nas segundas, quartas e sextas-feiras, ficando os outros dias em descanso para aeração do solo. Os resultados mostraram que os solos foram capazes de reduzir as concentrações de DBO afluentes significativamente, com eficiência de remoção variando entre 97 e 99%. A remoção se deu pela mineralização da matéria orgânica e seu acúmulo no solo. Durante o início da aplicação do esgoto, houve inicialmente uma redução nos teores de matéria orgânica nativa do solo que passaram a aumentar paulatinamente com a aplicação dos esgotos. A atividade dos microrganismos decompositores aumentou proporcionalmente à taxa de aplicação de esgoto, porém taxas elevadas indicaram uma tendência à inibição dessa atividade. Nos solos das unidades controles, houve menores perdas de CO2 para a atmosfera, indicando uma maior imobilização do carbono nos solos.

Remoção da fração oleosa de embalagens de lubrificantes automotivos pós-consumo por drenagem gravitacional

Directory of Open Access Journals (Sweden)

Harley Moraes Martins

Full Text Available RESUMO: Este trabalho aborda a questão do gerenciamento de embalagens pós-consumo de lubrificantes automotivos, considerando as dificuldades inerentes à implementação do sistema de logística reversa - prática compulsória por força de lei (Brasil, Lei 12.305/2010 - e a ineficácia dos atuais métodos utilizados para remoção da fração oleosa residual, necessária ao reprocessamento do material plástico por reciclagem mecânica direta. Para determinar metodologia apropriada para limpeza dos frascos de lubrificantes foram conduzidos experimentos para avaliar a influência do aquecimento e da posição das embalagens durante o processo de drenagem gravitacional. O procedimento analítico realizado proporcionou a escolha de uma combinação de variáveis capaz de assegurar remoção de elevado teor do resíduo oleoso com menor gasto energético. A otimização foi feita utilizando um planejamento experimental do tipo composto central com triplicata no ponto central. Os dados obtidos nos ensaios foram analisados com recursos estatísticos e demonstraram que ambos os parâmetros avaliados interferem, de forma significativa, no processo em estudo. Os resultados apontaram aumento da eficácia do processo quando a drenagem é realizada em temperaturas superiores a 35ºC e com a embalagem inclinada em ângulos próximos a 70º em relação à horizontal. Nessas condições, percentuais de remoção de óleo residual superaram 95% após 35 minutos de drenagem.

Test Plan for Rotary Mode Core Sample Truck Grapple Hoist Level Wind System

Energy Technology Data Exchange (ETDEWEB)

BOGER, R.M.

1999-12-09

A Grapple Hoist Assembly is currently used on the Rotary Mode Core Sampling Trucks (RMCSTs) to actuate the sampler and retrieve the pintle rod during sampling operations. The hoist assembly includes a driven drum approximately two inches wide and six inches in diameter that rotates to pay out or reel in the 5/32-in. cable The current Grapple Hoist Assembly, detailed on drawing H-2-690057, is prone to ''bird nesting'' the cable on the drum. ''Bird nesting'' is a condition in which the cable does not wind onto the drum in a uniformly layered manner, but winds in a random fashion where the cable essentially ''piles up'' inappropriately on the drum and, on some occasions, winds on the drum drive shaft. A system to help control this ''bird nesting'' problem has been designed as an addition to the existing components of the Grapple Hoist Assembly. The new design consists of a mechanism that is timed with, and driven by, the shaft that drives the drum. This mechanism traverses back and forth across the width of the drum to lay the cable on the drum in a uniformly layered manner. This test plan establishes the acceptance criteria, test procedure and test conditions It also describes the test apparatus necessary to verify the adequacy of the level wind system design. The test is defined as qualification testing (LMHC 1999b) and as such will be performed at conditions beyond the parameters that the Grapple Hoist Assembly is allowed to operate by the Safety Equipment List (SEL)(LMHC 1998).

Propagules removal in fragments of native forest and in reforested areas in an Araucaria Forest region of Paraná State Remoção de propágulos em fragmento de floresta nativa e reflorestamentos numa região de Floresta Ombrófila Mista do estado do Paraná

Directory of Open Access Journals (Sweden)

Yves Rafael Bovolenta

2011-06-01

Full Text Available A question that has been discussed is the role that reforestations with exotic species in native fauna and several studies have shown that removal of propagules is lower in these environments. This study compared the removal rate of propagules (araucaria seeds, peanuts, corn from areas of native forest (FN, reforestations of Pinus taeda L. (RP, Eucalyptus saligna Sm. (RE and Araucaria angustifolia (Bertol Kuntze (RA. In FN all propagules were removed. There was no difference in the removal of araucaria seeds between FN and RA, and removal rate in both areas differ from the removal rate in the RP and RE. In RP there was high removal of peanuts, while the RE showed the lowest value of removal of the three propagules. The low removal rates in reforestation of pine and eucalyptus reflect the decreased exploitation of these habitats for wildlife, which may be related to a poorly structured understory. Uma questão que tem sido discutida é o papel das monoculturas florestais exóticas na manutenção da fauna nativa e vários estudos têm mostrado que a remoção de propágulos é menor nesses ambientes. O presente trabalho comparou a taxa de remoção de propágulos (pinhão, amendoim, milho entre áreas de Floresta Nativa (FN, Reflorestamentos de Pinus taeda L. (RP, de Eucalyptus saligna Sm. (RE e Araucaria angustifolia (Bertol Kuntze (RA. Na FN, todos os propágulos foram removidos e não houve diferença significativa na remoção de pinhão entre a FN e o RA. A remoção de propágulos nessas áreas diferiu da remoção no RP e RE. No RP, houve alta remoção de amendoim, enquanto que o RE apresentou os menores valores de remoção dos três propágulos. As baixas taxas de remoção nos reflorestamentos de pinus e eucalipto refletem a menor exploração desses habitas pela fauna, o que pode estar relacionado com um subosque pouco estruturado.

Remoção de cianobactérias utilizando filtro de lavagem contínua

Directory of Open Access Journals (Sweden)

Bianca Coelho Machado

2011-01-01

Full Text Available Visando a remoção de cianobactérias, a presente pesquisa utilizou a dupla filtração direta ascendente como sistema de tratamento de água de abastecimento (filtro de lavagem contínua e filtro ascendente convencional, com taxa de filtração de 150 m³ (m² d-1 em ambos os filtros. O tratamento testado foi o seguinte: adição de coagulante na entrada de ambos os filtros. Os parâmetros avaliados foram: turbidez, cor aparente, cor verdadeira, carbono orgânico dissolvido (COD, absorbância 254 nm, clorofila a, densidade de cianobactérias e perda de carga. O sistema de dupla filtração se mostrou eficiente para a remoção de cianobactérias e vantajoso quanto aos serviços operacionais, tendo em vista que diminui as lavagens do segundo filtro, permitindo obter carreira de filtração de até 293 h e um grande aumento na produção efetiva de água.Abstract Aiming the cyanobacteria removal, the present research utilized the upflow double filtration as water treatment system (continuous backwashing filter and conventional ascendant filter, with filtration rate of 150 m³ (m² d-1 in both filters. The treatment tested was: coagulant addition in both filters inlet. The parameters evaluated were: turbidity, apparent color, true color, dissolved organic carbon (DOC, absorbance at 254 nm, chlorophyll a, cyanobacteria density and loss of load. The double filtration system has proven efficient to the cyanobacteria removal and worthwhile in terms of operational services, once it lessens the second filter washings, which allows obtaining a filtration period up to 293 h and a significant increase in the effective water production.

Remoção do herbicida 2,4-D por meio do tratamento convencional da água e adsorção em carvão ativado granular em instalação piloto

OpenAIRE

Brega, Renata Santos

2014-01-01

O crescimento populacional empurra a produção agrícola em direção ao uso intensivo dos agrotóxicos que aumentam a produtividade. Porém, seu uso incorreto pode resultar em grave problema para as estações de tratamento da água e impactar negativamente na saúde pública. Segundo estudos em escala laboratorial, o tratamento convencional, um dos mais utilizados no Brasil, apresenta remoção insignificante do 2,4-D. A adsorção em carvão ativado tem se demonstrado como tecnologia eficiente na remoção ...

On the aspiration characteristics of large-diameter, thin-walled aerosol sampling probes at yaw orientations with respect to the wind

International Nuclear Information System (INIS)

Vincent, J.H.; Mark, D.; Smith, T.A.; Stevens, D.C.; Marshall, M.

1986-01-01

Experiments were carried out in a large wind tunnel to investigate the aspiration efficiencies of thin-walled aerosol sampling probes of large diameter (up to 50 mm) at orientations with respect to the wind direction ranging from 0 to 180 degrees. Sampling conditions ranged from sub-to super-isokinetic. The experiments employed test dusts of close-graded fused alumina and were conducted under conditions of controlled freestream turbulence. For orientations up to and including 90 degrees, the results were qualitatively and quantitatively consistent with a new physical model which takes account of the fact that the sampled air not only diverges or converges (depending on the relationship between wind speed and sampling velocity) but also turns to pass through the plane of the sampling orifice. The previously published results of Durham and Lundgren (1980) and Davies and Subari (1982) for smaller probes were also in good agreement with the new model. The model breaks down, however, for orientations greater than 90 degrees due to the increasing effect of particle impaction onto the blunt leading edge of the probe body. For the probe facing directly away from the wind (180 degree orientation), aspiration efficiency is dominated almost entirely by this effect. (author)

Diversidade microbiana associada ao uso de sulfeto como doador de elétrons para a remoção de nitrogênio de efluentes de reatores anaeróbios aplicados ao tratamento de esgotos sanitários

OpenAIRE

Débora Faria Fonseca

2012-01-01

A ampla ocorrência de contaminação de águas por compostos de nitrogênio em concentrações superiores às recomendadas pela legislação tem suscitado interesse no desenvolvimento de tecnologias viáveis de remoção desses compostos. A remoção biológica de nitrogênio apresenta como principais vantagens os custos relativamente reduzidos e a possibilidade de maior eficiência. Compostos reduzidos de enxofre como sulfetos podem ser oxidados a enxofre elementar ou a sulfato por bactérias oxidantes de sul...

Growth of doped and pure monocrystalline fibers and gradient crystals of REMO{sub 4} compounds (RE = rare earths and M = Nb and Ta); Crescimento de fibras monocristalinas puras e dopadas, e cristais gradientes de compostos REMO{sub 4} (RE= terras raras e M = Nb e Ta)

Energy Technology Data Exchange (ETDEWEB)

Octaviano, E.S.; Levada, C.L.; Missiato, O., E-mail: esoctaviano@if.sc.usp.br [Academia da Forca Aerea, Campo Fontenelle, Pirassununga , SP (Brazil). Div. de Ensino; Semenzato, M.J.; Silva, R.A.; Andreeta, J.P. [Universidade de Sao Paulo (USP), Sao Carlos, SP (Brazil). Instituto de Fisica

2009-07-01

A desirable alternative for a faster development, characterization and application of material of technological interest has been the growth of single crystal fibers by LHPG - Laser Heated Pedestal Growth. In this work it was reported the growth of pure, doped and gradient single crystal fibers of the chemical formulation REMO{sub 4} (M = Nb e Ta, e RE= Rare Earth), characterized through primary techniques such as X-Ray and optical spectroscopy. (author)

Remoção de fármacos e desreguladores endócrinos em estações de tratamento de esgoto: revisão da literatura

Directory of Open Access Journals (Sweden)

Sérgio Francisco de Aquino

2013-09-01

Full Text Available O monitoramento ambiental dos chamados microcontaminantes ou micropoluentes vem ganhando grande interesse da comunidade científica desde os anos 1970. Nesse grupo de contaminantes estão incluídos fármacos de diversas classes, produtos de limpeza e higiene pessoal, substâncias aplicadas na produção de plásticos e resinas, pesticidas, hormônios naturais e seus subprodutos, entre outros compostos. A principal via de contaminação do meio ambiente com fármacos e desreguladores endócrinos (DE é o lançamento de esgotos in natura e tratado. Nesse contexto, este artigo compila dados de ocorrência de fármacos e DE no afluente e efluente de estações de tratamento de esgoto (ETE, discute os mecanismos envolvidos na sua remoção em ETE e faz uma análise comparativa da remoção de tais compostos em diferentes sistemas de tratamento

Remoção de demanda química de oxigênio e nitrogênio total Kjeldahl de efluente de indústria de vegetais congelados por Reator em Batelada Sequencial

Directory of Open Access Journals (Sweden)

Thaís Luciana Betto

2013-09-01

Full Text Available O objetivo deste trabalho foi estudar o tratamento biológico de efluente de indústria de vegetais congelados em Reator em Batelada Sequencial (RBS, verificando o efeito da concentração de Sólidos Suspensos Voláteis (SSV, Demanda Química de Oxigênio inicial (DQOi e aeração na remoção biológica de carbono e nitrogênio, a fim de obter um efluente tratado que atenda aos padrões de lançamento recomendados pela legislação ambiental brasileira. Nesta pesquisa, o tratamento dos efluentes foi feito em um RBS, utilizando concentração de SSV variando entre 2000 mg.L-1 e 4000 mg.L-1, DQOi variando entre 300 mg.L-1 e 600 mg.L-1, e quantidade de aeração variando entre 3 L.min-1 e 6 L.min-1. Os resultados mostram que a maior eficiência de remoção para DQO foi de 88%, e para nitrogênio total Kjeldahl (NTK foi de 74,9%. As condições otimizadas para remoção de DQO e NTK do efluente estudado foram: DQO inicial de 600 mg.L-1, aeração de 4,5 L.min-1 e concentração de SSV de 2000 mg.L-1

Uso de biomassa seca de aguapé (Eichornia crassipes visando à remoção de metais pesados de soluções contaminadas = Use of water hyacinth (Eichornia crassipes dry biomass for removing heavy metals from contaminated solutions

Directory of Open Access Journals (Sweden)

Affonso Celso Gonçalves Junior

2009-01-01

Full Text Available O presente trabalho avaliou a eficiência da biomassa seca de aguapé (Eichornia crassipes na remoção dos metais pesados cádmio (Cd, chumbo (Pb, cromo (Cr, cobre (Cu, zinco (Zn e níquel (Ni de soluções preparadas com estes metais. O delineamento utilizado foi inteiramente casualizado, com cinco tratamentos (soluções com diferentes concentrações dos metais pesados e quatro repetições. A biomassa seca permaneceu nas soluções dos tratamentos por um período de 48h, e nos intervalos de 1; 2; 3; 6; 12; 24; 36 e 48h após a instalação do experimento, coletaram-se alíquotas de cada tratamento,determinando-se a maior remoção de cada metal pesado pela biomassa seca do aguapé. Foi realizada digestão nitroperclórica na biomassa seca e determinação dos teores dos metais na biomassa e nas alíquotas por espectrometria de absorção atômica, modalidade chama. Paraos metais Cd, Pb, Cr, Cu e Zn ocorreu remoção significativa pela massa seca do aguapé nos diferentes tratamentos, enquanto para o Ni não foi encontrada diferença significativa. Dessa forma, conclui-se que a biomassa seca produzida, a partir do aguapé Eichornia crassipes, é um excelente material para a remoção, tanto em pequena como em grande escala, de corpos hídricos contaminados com metais pesados.The present work evaluated the efficiency of the dry biomass of water hyacinth (Eichornia crassipes in the removal of heavy metalscadmium (Cd, lead (Pb, chromium (Cr, cupper (Cu, zinc (Zn and nickel (Ni from solutions prepared with these metals. The delineation used was entirely randomized, with five treatments (solutions with different concentrations of heavy metals and fourrepetitions. The dry biomass remained in the treatment solutions for a period of 48h. In the intervals of 1; 2; 3; 6; 12; 24; 36 and 48h after experiment installation, samples were collected of each treatment, determining the greater removal for each heavy metal by water hyacinth dry biomass. Nitro

Engineering task plan for the development, fabrication and installation of rotary mode core sample truck grapple hoist box level wind system

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

This Engineering Task Plan is to design, generate fabrication drawings, fabricate, test, and install the grapple hoist level wind system for Rotary Mode Core Sample Trucks (RMCST) 3 and 4. Deliverables will include generating fabrication drawings, fabrication of one level wind system, updating fabrication drawings as required, and installation of level wind systems on RMCST 3 or 4. The installation of the level wind systems will be done during a preventive maintenance outage

Uso de filtros de carvão ativado granular associado a microrganismos para remoção de fármacos no tratamento de água de abastecimento

Directory of Open Access Journals (Sweden)

Rívea Medri Borges

Full Text Available RESUMO O modo de vida das sociedades modernas originou o aporte diário, nos ambientes aquáticos, de fármacos e outras inúmeras moléculas de uso contínuo, compostos emergentes, com potencial de risco à saúde humana principalmente pela exposição em razão da inevitável contaminação dos mananciais de abastecimento de água e da transferência para as estações de tratamento de água (ETA, onde não são removidos. O uso de carvão ativado granular na filtração demonstra ser uma opção viável para ETA, porém, uma eficiência satisfatória requer regeneração periódica do material, onerando o tratamento. Contudo, observa-se que em baixas taxas de filtração a colonização natural dos filtros por microrganismos - formação de biofilme - pode ser uma alternativa para aumentar o tempo de vida útil do carvão, bem como para decompor essas moléculas complexas em elementos minerais assimiláveis, reintroduzindo-os nos ciclos biogeoquímicos naturais. Este trabalho avaliou, durante 24 semanas, em condições de laboratório, o carvão ativado com biofilme como meio filtrante para remoção dos fármacos: diclofenaco de sódio, ibuprofeno, naproxeno e amoxicilina; experimentou em sistema batch o potencial dos microrganismos colonizadores de filtros em degradar os fármacos testados, assim como identificou filogeneticamente os microrganismos predominantes na biodegradação. Os resultados demonstram a remoção dos fármacos acima de 80%. Constatou-se a presença das bactérias dos gêneros Bacillus , Burkholderia , Cupriavidus , Pseudomonas , Shinella , e Sphingomonas . Este estudo permite inferir a capacidade de remoção de fármacos por bactérias presentes em filtros de carvão ativado e o possível uso dessa tecnologia como alternativa de controle e remoção dessas substâncias no tratamento de água potável.

Growth of doped and pure monocrystalline fibers and gradient crystals of REMO_4 compounds (RE = rare earths and M = Nb and Ta)

International Nuclear Information System (INIS)

Octaviano, E.S.; Levada, C.L.; Missiato, O.; Semenzato, M.J.; Silva, R.A.; Andreeta, J.P.

2009-01-01

A desirable alternative for a faster development, characterization and application of material of technological interest has been the growth of single crystal fibers by LHPG - Laser Heated Pedestal Growth. In this work it was reported the growth of pure, doped and gradient single crystal fibers of the chemical formulation REMO_4 (M = Nb e Ta, e RE= Rare Earth), characterized through primary techniques such as X-Ray and optical spectroscopy. (author)

Estudo in vitro da eficácia do gel de EDTA 24% na remoção de smear layer e exposição de fibras colágenas da superfície radicular

OpenAIRE

Sousa, Cliciane Portela [UNESP

2004-01-01

O objetivo do presente estudo foi avaliar, por meio da Microscopia Eletrônica de Varredura (MEV), a eficácia do condicionamento químico com o gel de EDTA 24% na remoção de smear layer e exposição de fibras colágenas, avaliando-se diferentes marcas comerciais, modos e tempos de aplicação. Dentes humanos extraídos foram desgastados com fresa diamantada para remoção do cemento e raspados com curetas de Gracey 5-6 para formação de smear layer. Após o seccionamento dentário, as 225 amostras obtida...

Ativação de adsorventes carbonosos para a remoção de corantes de efluentes têxteis

OpenAIRE

Sonai, Gabriela Gava

2012-01-01

Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-Graduação em Engenharia Química A adsorção é um processo que vem ganhando importância na indústria têxtil para a remoção de corantes de efluentes industriais, sendo geralmente utilizado o carvão ativado. Devido ao alto custo deste material, muitos estudos visam o desenvolvimento de adsorventes alternativos e de baixo custo. Neste trabalho foram investigadas as diferentes técnicas de prepara...

Motivação e habitação : aspectos motivacionais na remoção de favelados

OpenAIRE

Freitas, Carmencita de Almeida

1986-01-01

O objetivo central deste trabalho é verificar a aplicabilidade da teoria da motivação de Abraham Maslow (1954) ao processo de remoção de favelados para conjuntos habitacionais no Rio de Janeiro. Visando a este objetivo, acompanhamos e pesquisamos uma amostra de 95 famílias residentes na área palafitada da Favela da Marep, removidas, para a Vila do João, através PROMORAR/PROJETO RIO, em 1982. O trabalho se orientou principalmente pela hipótese de que a satisfação parceail da necessidade de s...

Evaluation of enamel surface after bracket debonding and polishing Avaliação da superfície do esmalte dentário após a remoção do braquete e polimento

Directory of Open Access Journals (Sweden)

Lilian Maria Brisque Pignatta

2012-08-01

Full Text Available INTRODUCTION: Preserving the dental enamel structure during removal of orthodontic accessories is a clinician's obligation. Hence the search for an evidence based debonding protocol. OBJECTIVE: to evaluate and compare, by means of scanning electron microscopy (SEM, the effects of four different protocols of bracket debonding and subsequent polishing on enamel surface, and to propose a protocol that minimizes damage to enamel surface. METHODS: Twelve bovine permanent incisors were divided into four groups according to the instrument used for debonding and removal of the adhesive remnant. In groups 1 and 2, brackets were debonded with a straight debonding plier (Ormco Corp., Glendora, California, USA, and in groups 3 and 4, debonding was performed with the instrument Lift-Off (3M Unitek, Monrovia, California, USA. In groups 1 and 3, the adhesive remnant was removed using a long adhesive removing plier (Ormco Corp., Glendora, California, USA and in groups 2 and 4, residual adhesive was removed with a tungsten carbide bur (Beavers Dental at high-speed. After each stage of debonding and polishing, enamel surfaces were replicated and electron micrographs were obtained with 50 and 200X magnification. RESULTS: All four protocols of debonding and polishing caused enamel irregularities. CONCLUSION: Debonding brackets with straight debonding plier, removal of adhesive remnant with a tungsten carbide bur and polishing with pumice and rubber cup was found to be the protocol that caused less damage to enamel surface, therefore this protocol is suggested for debonding brackets.INTRODUÇÃO: a preservação da estrutura de esmalte após a remoção dos acessórios ortodônticos é obrigação do clínico. Portanto, procura-se um protocolo de descolagem com bases científicas. OBJETIVO: objetivou-se avaliar por microscopia eletrônica de varredura (MEV a influência de quatro protocolos de remoção de braquetes e polimento da superfície do esmalte e propor um

Caracterização de dois protocolos de avaliação de preensão manual para prescrição de treinamento no remo

Directory of Open Access Journals (Sweden)

Affonso Celso Kulevicz da Silva

2015-06-01

Full Text Available Objetivou-se verificar as características de dois protocolos de avaliação de força de preensão manual como subsídio para prescrição de treinamento no remo. Participaram seis atletas profissionais da modalidade de remo (25 ± 5 anos e 11 não atletas, todos homens. Dois protocolos de avaliação (contínuo e intervalar foram efetuados. Os valores dos parâmetros de força e decréscimo percentual da força calculados foram empregados para verificar diferenças entre os membros (teste t pareado e entre os grupos (teste t independente. O protocolo contínuo mostrou-se mais sensível para detectar diferenças nos valores de força e decréscimo percentual de força entre diferentes membros e entre os grupos, enquanto o protocolo intervalar foi eficaz para identificar os valores de força máxima.

Modelling of wind power plant controller, wind speed time series, aggregation and sample results

DEFF Research Database (Denmark)

Hansen, Anca Daniela; Altin, Müfit; Cutululis, Nicolaos Antonio

This report describes the modelling of a wind power plant (WPP) including its controller. Several ancillary services like inertial response (IR), power oscillation damping (POD) and synchronising power (SP) are implemented. The focus in this document is on the performance of the WPP output...... and not the impact of the WPP on the power system. By means of simulation tests, the capability of the implemented wind power plant model to deliver ancillary services is investigated....

Wind power prediction models

Science.gov (United States)

Levy, R.; Mcginness, H.

1976-01-01

Investigations were performed to predict the power available from the wind at the Goldstone, California, antenna site complex. The background for power prediction was derived from a statistical evaluation of available wind speed data records at this location and at nearby locations similarly situated within the Mojave desert. In addition to a model for power prediction over relatively long periods of time, an interim simulation model that produces sample wind speeds is described. The interim model furnishes uncorrelated sample speeds at hourly intervals that reproduce the statistical wind distribution at Goldstone. A stochastic simulation model to provide speed samples representative of both the statistical speed distributions and correlations is also discussed.

Desempenho de um reator Fenton em escala industrial aplicado à remoção de fenóis em uma planta de recuperação de resíduos da indústria de papel e celulose

Directory of Open Access Journals (Sweden)

Everton Skoronski

2015-11-01

Full Text Available Este trabalho descreve o desempenho de um reator Fenton em grande escala usado para remoção de fenol em uma planta de valorização dos resíduos da indústria de papel e celulose. O efluente consiste em óleo vegetal e fenol. A estação de tratamento objetiva tratar 4 m3 h-1 e é constituída por um pré-tratamento para remoção de óleo, reator Fenton, Flotador de Ar Dissolvido - FAD e uma lagoa de aeração. Para a avaliação da estação de tratamento foram comparadas análises próprias do efluente com análises feitas em laboratório certificado. A eficiência global de remoção de fenol é maior do que 99,7%. Foi demonstrado que a combinação do processo de oxidação avançada com o biológico constitui-se em um sistema de tratamentos interessante a fim de remover contaminantes recalcitrantes.

Three Proposed Compendia for Genesis Solar Wind Samples: Science Results, Collector Materials Characterization and Cleaning Techniques

Science.gov (United States)

Allton, J. H.; Calaway, M. J.; Nyquist, L. E.; Jurewicz, A. J. G.; Burnett, D. S.

2018-01-01

Final Paper and not the abstract is attached. Introduction: Planetary material and cosmochemistry research using Genesis solar wind samples (including the development and implementation of cleaning and analytical techniques) has matured sufficiently that compilations on several topics, if made publically accessible, would be beneficial for researchers and reviewers. We propose here three compendia based on content, organization and source of documents (e.g. published peer-reviewed, published, internal memos, archives). For planning purposes, suggestions are solicited from potential users of Genesis solar wind samples for the type of science content and/or organizational style that would be most useful to them. These compendia are proposed as living documents, periodically updated. Similar to the existing compendia described below, the curation compendia are like library or archival finding aids, they are guides to published or archival documents and should not be cited as primary sources.

Avaliação experimental e modelagem matemática de filtros anaeróbios como alternativa de baixo custo para remoção de algas de efluentes de lagoas de estabilização

Directory of Open Access Journals (Sweden)

Germário Marcos Araújo

Full Text Available RESUMO Nesta pesquisa, estudou-se o desempenho de três filtros biológicos anaeróbios com novos e diferentes meios de suporte em tempos de detenção hidráulica (TDH distintos (5,5 e 11,1 horas, objetivando a remoção de algas de efluentes de lagoas de estabilização. O considerável desempenho no pós-tratamento (remoções de até 77,4% pode ser atribuído à atuação dos mecanismos de sedimentação, retenção física e assimilação biológica. Foi desenvolvido um modelo de decaimento para clorofila com base na simplificação da equação de transporte de massa. O coeficiente global de decaimento foi descrito como uma função dos números de Reynolds e Weber, obtida por meio de ajuste aos dados experimentais com um coeficiente de determinação superior a 0,96. Para confirmação de que a função de Reynolds e Weber descreve bem o comportamento de k, foram realizadas simulações do impacto das seguintes variáveis na eficiência de remoção de algas: comprimento do filtro (altura do leito, diâmetro do filtro, diâmetro do meio suporte, porosidade, vazão, tensão superficial e da viscosidade do líquido. As simulações desenvolvidas demonstraram coerência nos resultados, reforçando que os números de Reynolds e Weber, assim como o modelo de fluxo em pistão, podem ser usados para descrever o processo de remoção de algas em filtros anaeróbios.

Turbulent wind at the equatorial segment of an operating Darrieus wind turbine blade

Science.gov (United States)

Connell, J. R.; Morris, V. R.

1989-09-01

Six turbulent wind time series, measured at equally spaced equator-height locations on a circle 3 m outside a 34-m Darrieus rotor, are analyzed to approximate the wind fluctuations experienced by the rotor. The flatwise lower root-bending stress of one blade was concurrently recorded. The wind data are analyzed in three ways: wind components that are radial and tangential to the rotation of a blade were rotationally sampled; induction and wake effects of the rotor were estimated from the six Eulerian time series; and turbulence spectra of both the measured wind and the modeled wind from the PNL theory of rotationally sampled turbulence. The wind and the rotor response are related by computing the spectral response function of the flatwise lower root-bending stress. Two bands of resonant response that surround the first and second flatwise modal frequencies shift with the rotor rotation rate.

Emprego do carvão ativado para remoção de atrazina em água de abastecimento público

OpenAIRE

Coelho,Edumar Ramos Cabral; Vazzoler,Heverton; Leal,Waldileira Pereira

2012-01-01

A atrazina é um dos herbicidas mais utilizados no mundo, sendo encontrada em águas superficiais e subterrâneas. Pertence à classe das s-triazinas, possui potencial carcinogênico e apresenta toxicidade como disruptor endócrino. A reconhecida limitação dos processos de tratamento de água, os quais empregam a coagulação química na remoção da atrazina e os efeitos na saúde, motivou este trabalho, considerando a adsorção em carvão ativado como tecnologia alternativa. O estudo experimental consisti...

L’antropologia filosofica di Remo Cantoni: umanismo critico, “connessione orizzontale” e partecipazione

Directory of Open Access Journals (Sweden)

DI GIOVANNI, Elisabetta

2016-06-01

Full Text Available The paper proposes a critical reflection on Remo Cantoni’s philosophical thought, with particular regards to his anthropological point of view that addresses concepts such as “critical humanism” and “horizontal connection”. The strict relationship between anthropology and participation are his main topics on which he has made outstanding remarks in the second decade of XXth century in the Italian cultural panorama. Since his early works, Cantoni points out the need to develop a different way of analysing the pluridimensionality of human beings and widely debates contemporary European cultural context after the end of World War II. The paper tries to put in evidence how Cantoni’s anthropological thought originally tends to a knowledgical intentionality dimension which should be taken into account for ethnographic investigation. In order to apply his point view, he suggests to consider an epistemological approach which could connect all the social-scientific sciences through a “horizontal connection”, whose aim is to gain a vital relationship of culture with the existing variety and alterity.

Aumento da aeração nasal após remoção de hábitos de sucção e terapia miofuncional Nasal breathing after removing sucking habit and myofunctional therapy

Directory of Open Access Journals (Sweden)

Viviane Veroni Degan

2007-03-01

Full Text Available OBJETIVO: avaliar os efeitos da associação entre a remoção de hábitos de sucção e a Terapia Miofuncional Orofacial na ampliação da aeração nasal. MÉTODOS: vinte crianças na faixa de etária de quatro anos a quatro anos e oito meses foram distribuídas em dois grupos denominados de: Grupo REM (submetido apenas à remoção de hábitos e Grupo TMF (submetido à remoção de hábitos e posteriormente à Terapia Miofuncional Orofacial. O fluxo de ar expirado pelas narinas foi registrado por meio do espelho nasal milimetrado de Altmann e quantificado em papel milimetrado denominado de Bloco de Referência do Espelho de Altmann. Os exames foram realizados em três momentos (pré-tratamento, 60 e 180 dias após. Os resultados foram submetidos à análise estatística, utilizando-se Test t para duas amostras independentes e para dados pareados, considerando nível de significância valores pPURPOSE: to evaluate the influence of removing pacifier and baby bottle sucking habit and Myofunctional Therapy in increasing nasal airing. METHODS: twenty children aged up to four year, were distributed in two groups according to the treatment, and named: REM Group (only submitted to habits removal and FMT Group (submitted to habits removal and later to Myofunctional Therapy. The data obtained from the air flow expired by the nostrils were obtained by using the millimeter nasal mirror of Altmann and quantified in millimeter paper (reference block. The exams were accomplished in three times (pre-treatment, 60 and 180 days after treatment. The data were submitted to t Test for two independent samples and the paired t Test (p < 0.05. RESULTS: it was observed that the increase of the nasal airing after treatments were significantly superior for the FMT Group than for the REM Group (p < 0.0001. CONCLUSION: Myofunctional Therapy was able to improve increase of nasal airing and consequently enhancement of nasal breathing.

Remoção de sólidos suspensos e totais em biofiltros operando com esgoto doméstico primário para reuso na agricultura

Directory of Open Access Journals (Sweden)

Rafael Oliveira Batista

2013-02-01

Full Text Available Este trabalho objetivou analisar a remoção de sólidos suspensos e totais em biofiltros, preenchidos com lixo compostado, bagaço de cana-de-açúcar e serragem de madeira, submetidos às taxas de aplicação do esgoto doméstico de 0,5, 1,0 e 1,5 m³ m-2 d-1, em Viçosa-MG. Para isso, foi montada uma bancada experimental, constituída de 27 biofiltros, em área experimental da Universidade Federal de Viçosa. As concentrações de sólidos suspensos e totais foram determinadas, mensalmente, durante período de 153 dias. O experimento foi montado no esquema de parcelas subsubdivididas, tendo, nas parcelas, as taxas de aplicação do esgoto doméstico; nas subparcelas, os tipos de material orgânico e, nas subsubparcelas, os períodos de avaliação, no delineamento em blocos casualizados, com três repetições. Os resultados indicaram que os biofiltros proporcionaram remoções de sólidos suspensos e totais de até 82 e 46%, no esgoto doméstico, após 153 dias de operação; a serragem de madeira foi o tipo de material orgânico filtrante com melhor desempenho no tratamento de esgoto doméstico; as aplicações de taxas de 0,5, 1,0 e 1,5 m³ m-2 d-1 de esgoto não apresentaram diferenças quanto à remoção de sólidos suspensos e totais; e a utilização de biofiltros minimiza a obstrução de emissores causada por sólidos suspensos, quando do aproveitamento agrícola de esgoto doméstico, por via do sistema de irrigação por gotejamento.

Hierarquização da eficiência de remoção de cianotoxinas por meio de adsorção em carvão ativado granular

Directory of Open Access Journals (Sweden)

Maria Natália Costa e Silva

2017-08-01

Full Text Available RESUMO O trabalho objetivou avaliar a remoção concomitante de duas cianotoxinas - microcistina-LR e saxitoxina-STX - por meio da adsorção em carvão ativado granular. Em primeira etapa, três carvões de granulometrias distintas, dois de coco de dendê e um mineral, foram avaliados na adsorção de microcistina-LR em água destilada e tratada com concentrações de 3,9 a 9,4 ug.L-1. O carvão de coco de dendê de menor granulometria apresentou desempenho mais uniforme, tanto no que tange à remoção (% de microcistina-LR, quanto ao volume de efluente produzido consoante com as recomendações do padrão de potabilidade brasileiro. Em segunda etapa, apenas para o carvão selecionado na etapa precedente, concentrações de microcistina-LR e saxitoxina-STX aproximadamente 50% superiores dos limites do mesmo padrão de potabilidade foram dispersas em água destilada. Tais ensaios de adsorção evidenciaram que apenas a adsorção de saxitonina não foi influenciada pela simultaneidade das duas cianotoxinas.

A 15N-poor isotopic composition for the solar system as shown by Genesis solar wind samples.

Science.gov (United States)

Marty, B; Chaussidon, M; Wiens, R C; Jurewicz, A J G; Burnett, D S

2011-06-24

The Genesis mission sampled solar wind ions to document the elemental and isotopic compositions of the Sun and, by inference, of the protosolar nebula. Nitrogen was a key target element because the extent and origin of its isotopic variations in solar system materials remain unknown. Isotopic analysis of a Genesis Solar Wind Concentrator target material shows that implanted solar wind nitrogen has a (15)N/(14)N ratio of 2.18 ± 0.02 × 10(-3) (that is, ≈40% poorer in (15)N relative to terrestrial atmosphere). The (15)N/(14)N ratio of the protosolar nebula was 2.27 ± 0.03 × 10(-3), which is the lowest (15)N/(14)N ratio known for solar system objects. This result demonstrates the extreme nitrogen isotopic heterogeneity of the nascent solar system and accounts for the (15)N-depleted components observed in solar system reservoirs.

Multi-component wind measurements of wind turbine wakes performed with three LiDARs

Science.gov (United States)

Iungo, G. V.; Wu, Y.-T.; Porté-Agel, F.

2012-04-01

Field measurements of the wake flow produced from the interaction between atmospheric boundary layer and a wind turbine are performed with three wind LiDARs. The tested wind turbine is a 2 MW Enercon E-70 located in Collonges, Switzerland. First, accuracy of mean values and frequency resolution of the wind measurements are surveyed as a function of the number of laser rays emitted for each measurement. Indeed, measurements performed with one single ray allow maximizing sampling frequency, thus characterizing wake turbulence. On the other hand, if the number of emitted rays is increased accuracy of mean wind is increased due to the longer sampling period. Subsequently, two-dimensional measurements with a single LiDAR are carried out over vertical sections of the wind turbine wake and mean wake flow is obtained by averaging 2D measurements consecutively performed. The high spatial resolution of the used LiDAR allows characterizing in details velocity defect present in the central part of the wake and its downstream recovery. Single LiDAR measurements are also performed by staring the laser beam at fixed directions for a sampling period of about ten minutes and maximizing the sampling frequency in order to characterize wake turbulence. From these tests wind fluctuation peaks are detected in the wind turbine wake at blade top-tip height for different downstream locations. The magnitude of these turbulence peaks is generally reduced by moving downstream. This increased turbulence level at blade top-tip height observed for a real wind turbine has been already detected from previous wind tunnel tests and Large Eddy simulations, thus confirming the presence of a source of dangerous fatigue loads for following wind turbines within a wind farm. Furthermore, the proper characterization of wind fluctuations through LiDAR measurements is proved by the detection of the inertial subrange from spectral analysis of these velocity signals. Finally, simultaneous measurements with two

Remoção de polifenóis da farinha de folhas de mandioca Removal of polyphenols of the flour cassava leaves

Directory of Open Access Journals (Sweden)

Angelita Duarte Corrêa

2004-06-01

Full Text Available A farinha de folhas de mandioca apresenta baixa digestibilidade, mesmo possuindo um teor relativamente elevado em proteínas, principalmente, devido à presença de substâncias como os polifenóis. Visando melhorar o aproveitamento protéico desta farinha, empregaram-se três solventes (água, etanol 50mL/100mL e hidróxido de amônio 1mol/L para remover os polifenóis. Folhas maduras de mandioca foram coletadas na fase vegetativa, em três repetições, colocadas em bandejas de papel e secas à sombra sobre bancadas de madeira, em recinto fechado e arejado, em temperatura ambiente. Após secagem, retiraram-se os pecíolos e as folhas foram moídas e passadas em peneira de 40mesh. A farinha foi submetida, antes e após a remoção dos polifenóis, às análises de umidade, fibra detergente neutra (FDN, fibra detergente ácida (FDA, açúcares totais, proteína bruta, vitamina C total, beta-caroteno, cianeto, inibidor de tripsina, polifenóis e digestibilidade protéica in vitro. Após remoção dos polifenóis, houve diminuição dos teores de açúcares totais, vitamina C total, inibidor de tripsina e polifenóis e aumento de FDN, FDA, proteína bruta, beta-caroteno e digestibilidade protéica in vitro. Dos solventes empregados para remover polifenóis, o hidróxido de amônio foi o mais eficaz, com índice de remoção de 94%, seguido pelo etanol (83% e água (65%. A digestibilidade da proteína in vitro aumentou em 74%, quando o solvente empregado na remoção dos polifenóis foi o hidróxido de amônio.Even featuring a relatively high level in proteins, the flour of cassavaleaves presents low digestibility, mainly, due to the presence of such substances as polyphenols. Seeking to improve the protein availability of such flour, three solvents (water, ethanol 50mL/100mL and ammonium hydroxide 1mol/L were used for the removal of the polyphenols. Mature leaves of cassava were picked in phase of vegetative development, in three repetitions, they

Tratamento de esgotos sanitários em sistemas reatores UASB/wetlands construídas de fluxo horizontal: eficiência e estabilidade de remoção de matéria orgânica, sólidos, nutrientes e coliformes Domestic wastewater treatment in UASB-horizontal flow constructed wetlands systems: organic matter, solids, nutrients and coliforms removal

Directory of Open Access Journals (Sweden)

Maria Lúcia Calijuri

2009-09-01

Full Text Available Este trabalho apresentou os resultados de um estudo realizado durante 19 meses sobre o comportamento de wetlands construídas na remoção de matéria orgânica, sólidos, nutrientes e coliformes, em unidades em escala piloto de fluxo horizontal, subsuperficial e superficial, com tempo de detenção hidráulica entre 1,3 a 5,3 dias, operando como pós-tratamento de efluentes de reatores UASB (esgotos sanitários. A remoção de matéria orgânica e de sólidos mostrou-se elevada e estável, com eficiências médias de 70, 80 e 60% para SST, DBO5 e DQO, respectivamente. A remoção de nutrientes, após início promissor, mostrou-se instável e aparentemente influenciada pela temperatura. O sistema de tratamento revelou elevado potencial de remoção de coliformes, embora com variações relativamente amplas ao longo do período de operação: ≈ 2 log10 de remoção de coliformes totais e 2-4 log10 de remoção de Escherichia coli.This work presented the results of a 19-month study on the performance of constructed wetlands in terms of organic matter, solids, nutrients and coliforms removal in pilot scale unities with horizontal, subsurface and surface flow, with hydraulic retention time from 1.3 to 5.3 days, as post-treatment of UASB effluents (domestic wastewater. Organic matter and solids were effectively and consistently removed, with average values of 70, 80 and 60% for TSS, BOD5 and COD, respectively. Nutrients removal, after a promising start up, became unstable and apparently influenced by temperature. The treatment system has also shown high potential to remove coliforms, although with relatively wide variations over the study period: ≈ 2 log10 reduction of total coliforms and 2-4 log10 reduction of Escherichia coli.

Regional climate model for predicting meteorological and hydrological extremes - the example of the Rhine river catchment area; Regionales Klimamodell zur Vorhersage meteorologischer und hydrologischer Extremereignisse am Beispiel des Rheineinzugsgebietes

Energy Technology Data Exchange (ETDEWEB)

Richter, K.G.; Jacob, D.; Ebel, M.; Lenz, C.J.

2000-07-01

Although the forecasting of weather extremes has improved during the past few years, there is still a need of improvement in the accurate analysis and forecasting of extreme weather in practice, especially in the case of violent rain and high water events. Direct coupling of the atmospheric circulation model REMO (REgional-MOdell) with the hydrology model LARSIM (Large Area Runoff SImulation Model) can improve the quality of forecasting. The coupling was achieved in several stages. First, the meteorological state variables were calculated using REMO. The calculated output parameters, precipitation, global radiation, temperature, relative moisture, wind and ground level pressure were used as input for the LARSIM model for calculating high water runoff. The high water event of March 1988 was used as an example. [German] Die Vorhersage extremer meteorologischer Wetterphaenomene hat sich im Laufe der letzten Jahre deutlich verbessert. Dennoch besteht bis heute noch ein grosses Defizit an der genaueren Analyse und Vorhersage extremer meteorologischer Ereignisse und ihrer Auswirkung in der Praxis, insbesondere im Hinblick auf Starkregen und Hochwasserereignisse. Durch die direkte Kopplung des atmosphaerischen Zirkulationsmodells REMO (REgional-MOdell) mit dem Hydrologiemodell LARSIM (Large Aera Runoff Simulation Model) kann die Vorhersagequalitaet fuer extreme meteorologische und hydrologische Situationen erhoeht werden. Die Modellkopplung wird stufenweise durchgefuehrt. Bei der hier vorgestellten Einwegekopplung werden zunaechst die meteorologischen Zustandsgroessen mit dem Regionalmodell REMO berechnet. Als berechneter Modelloutput werden die Parameter Niederschlag, Globalstrahlung, Temperatur, relative Feuchte, Wind und Bodendruck an das Hydrologiemodell LARSIM uebergeben und hiermit der Hochwasserabfluss berechnet. Die Vorgehensweise wird im folgenden fuer das Hochwasser Maerz 1988 beschrieben. (orig.)

Analysis of impacts on hydrometeorological extremes in the Senegal River Basin from REMO RCM

Energy Technology Data Exchange (ETDEWEB)

Galiano, Sandra Garcia; Osorio, Juan Diego Giraldo [Technical Univ. of Cartagena, Dept. of Thermal Engineering and Fluids, Cartagena (Spain)

2010-06-15

West Africa is highly vulnerable to climate variability. The precipitation latitudinal gradient determines agricultural activities. The cultivated area of the Sahel is a densely populated region, whereas flood recession agriculture is practiced in the Senegal River Valley. The present study analyses both spatial-temporal rainfall patterns of the REMO Regional Climate Model (RCM) and observed rainfall data, focusing in particular on extreme hydro-meteorological phenomena. An analysis of simulated daily rainfall data was performed to determine the frequency and magnitude of length of dry spells, as well as the extreme rainfall events. A projected annual decrease in rainfall on horizon 2050 could be explained by two factors: the decrease in the percentage of rainy days on both west and north sides of the basin, and the decrease of precipitation amount for rainy days in the southern basin. Finally, an increase in the frequency of dry spell in the monsoon season by 2050 is projected. Such findings are significant in a framework of strategies for water resources management and planning at basin scale, in order to build adaptive capacity. (orig.)

Críticas e Denúncias: A Configuração da Ação Coletiva contra a Remoção de Favelas do Rio de Janeiro

Directory of Open Access Journals (Sweden)

Alexandre Magalhães

Full Text Available RESUMO Este artigo analisa os significados da reatualização de práticas e discursos sobre a “remoção” de favelas no Rio de Janeiro, abordando a formação da ação coletiva por parte dos moradores no período compreendido entre 2009 e 2012. Busca-se compreender como as concepções destes atores acerca deste assunto interferem em sua definição enquanto problema público. A crítica primordial realizada pelos moradores nestas circunstâncias seria aos “procedimentos”, ou seja, à “forma como é feita” a remoção pela administração pública. Esta crítica se constitui em dois níveis: no primeiro, como estas intervenções afetariam as rotinas de vida e as inúmeras redes de sociabilidade tão longamente constituídas no local de moradia. No segundo nível, a questão central vincula-se a como estes processos são vistos pelos impactados como uma espécie de “desqualificação moral”.

Influência da remoção de cotilédones no desenvolvimento de ramificações nas axilas cotiledonares de plântulas de leguminosas Effect of cotyledon removal on cotyledonal axillary shooting in seedlings of leguminosae

Directory of Open Access Journals (Sweden)

Odaci Fernandes de Oliveira

1999-12-01

Full Text Available Experimentos inteiramente casualizados foram conduzidos em condições de viveiro com o objetivo de verificar a importância da permanência de cotilédones no desenvolvimento de ramificações nas axilas cotiledonares de plântulas de Phaseolus vulgaris L., Vigna unguiculata (L. Walp., Leucaena leucocephala (Lam. De Wit, Prosopis juliflora (Sw., Tamarindus indica L. e Delonix regia L. Os tratamentos foram: remoção de ambos os cotilédones nos primeiro, segundo e terceiro dias da emergência, remoção de um só cotilédone no primeiro dia da emergência e não remoção de cotilédones. A recuperação do desenvolvimento em plântulas de P. vulgaris, avaliada através da ocorrência de ramificações, independe do número de cotilédones removidos no período de um a três dias da emergência, mas é menos eficiente que em V. unguiculata. A remoção de ambos os cotilédones em plântulas de V. unguiculata, no dia da emergência, afetou a recuperação do desenvolvimento dessas plântulas em comparação com os outros tratamentos. Em plântulas de L leucocephala, P. juliflora, T. indica e D. regia, a remoção de ambos os cotilédones, no período de um a três dias da emergência, sugere o aumento de mortalidade nessas plântulas. A remoção de um único cotilédone não afetou significativamente o percentual de sobrevivência das plântulas nem limitou o surgimento de brotações à axila cotiledonar correspondente ao cotilédone removido.Completely randomized experiments under greenhouse conditions were carried to study the role of cotyledons on the cotyledonal axillary shooting of Phaseolus vulgaris L., Vigna unguiculata (L. Walp., Leucaena leucocephala (Lam. De Wit, Prosopis juliflora (Sw., Tamarindus indica L. and Delonix regia L. The seedlings underwent the following treatments: removal of both cotyledons on the first to the third day after emergence, removal of only one cotyledon on the first day of emergence, and no cotyledon

Remoção de nitrogênio de efluente agroindustrial utilizando biorreatores = Nitrogen removal from agro-industrial wastewater using bioreactors

Directory of Open Access Journals (Sweden)

Roberta Miranda Teixeira

2008-07-01

Full Text Available O trabalho tem como objetivo avaliar a remoção de nitrogênio do efluente de uma indústria frigorífica utilizando biorreatores de nitrificação e desnitrificação. O sistema foi composto por dois reatores de fluxo contínuo operados em série: um reator híbrido(anaeróbio/anóxico conectado a um reator tipo filtro biológico de fluxo ascendente com aeração, o qual possuía um reciclo para o reator híbrido. A alimentação foi realizada com água residuária proveniente da estação de tratamento de uma indústria processadora de avese suínos. O acompanhamento do processo foi realizado por análises periódicas da concentração de amônia, nitrato, nitrito, alcalinidade, demanda química de oxigênio (DQO e pH. A eficiência do sistema na remoção de nitrogênio foi comparada com a eficiência teórica máxima para a razão de reciclo utilizada.This work evaluates the process of nitrogen removal from wastewater at a meat processing plant, using nitrification and denitrification in bioreactors. The system was composed of two reactors with continuous flow operated in series: a hybrid reactor(anaerobic/anoxic connected to an ascending flow biological filter with aeration, which recycled into the hybrid reactor. Feeding was accomplished with wastewater from the treatment station of a poultry and swine processing plant. The process was monitored by periodic analysis of the concentrations of ammonia, nitrate, nitrite, alkalinity, chemical oxygen demand (COD and pH. The nitrogen removal efficiency of the system was compared with the maximum theoretical efficiency for the recycle rate used.

Wind erosion control of soils using polymeric materials

Directory of Open Access Journals (Sweden)

Mohammad Movahedan

2012-07-01

Full Text Available Wind erosion of soils is one of the most important problems in environment and agriculture which could affects several fields. Agricultural lands, water reservoires, irrigation canals, drains and etc. may be affected by wind erosion and suspended particles. As a result wind erosion control needs attention in arid and semi-arid regions. In recent years, some polymeric materials have been used for improvement of structural stability, increasing aggregate stability and soil stabilization, though kind of polymer, quantity of polymer, field efficiency and durability and environmental impacts are some important parameters which should be taken into consideration. In this study, a Polyvinil Acetate-based polymer was used to treat different soils. Then polymer-added soil samples were investigated experimentally in a wind tunnel to verify the effecte of polymer on wind erosion control of the soils and the results were compared with water treated soil samples. The results of wind tunnel experiments with a maximum 26 m/s wind velocity showed that there was a significat difference between the erosion of polymer treated and water treated soil samples. Application of 25g/m2 polymer to Aeolian sands reduced the erosion of Aeolian sands samples to zero related to water treated samples. For silty and calyey soils treated by polymer, the wind erosion reduced minimum 90% in relation to water treated samples.

How Does a Regional Climate Model Modify the Projected Climate Change Signal of the Driving GCM: A Study over Different CORDEX Regions Using REMO

Directory of Open Access Journals (Sweden)

Claas Teichmann

2013-06-01

Full Text Available Global and regional climate model simulations are frequently used for regional climate change assessments and in climate impact modeling studies. To reflect the inherent and methodological uncertainties in climate modeling, the assessment of regional climate change requires ensemble simulations from different global and regional climate model combinations. To interpret the spread of simulated results, it is useful to understand how the climate change signal is modified in the GCM-RCM modelmodelgeneral circulation model-regional climate model (GCM-RCM chain. This kind of information can also be useful for impact modelers; for the process of experiment design and when interpreting model results. In this study, we investigate how the simulated historical and future climate of the Max-Planck-Institute earth system model (MPI-ESM is modified by dynamic downscaling with the regional model REMO in different world regions. The historical climate simulations for 1950–2005 are driven by observed anthropogenic forcing. The climate projections are driven by projected anthropogenic forcing according to different Representative Concentration Pathways (RCPs. The global simulations are downscaled with REMO over the Coordinated Regional Climate Downscaling Experiment (CORDEX domains Africa, Europe, South America and West Asia from 2006–2100. This unique set of simulations allows for climate type specific analysis across multiple world regions and for multi-scenarios. We used a classification of climate types by Köppen-Trewartha to define evaluation regions with certain climate conditions. A systematic comparison of near-surface temperature and precipitation simulated by the regional and the global model is done. In general, the historical time period is well represented by the GCM and the RCM. Some different biases occur in the RCM compared to the GCM as in the Amazon Basin, northern Africa and the West Asian domain. Both models project similar warming

Applicability of Synthetic Aperture Radar Wind Retrievals on Offshore Wind Resources Assessment in Hangzhou Bay, China

Directory of Open Access Journals (Sweden)

Rui Chang

2014-05-01

Full Text Available In view of the high cost and sparse spatial resolution of offshore meteorological observations, ocean winds retrieved from satellites are valuable in offshore wind resource assessment as a supplement to in situ measurements. This study examines satellite synthetic aperture radar (SAR images from ENVISAT advanced SAR (ASAR for mapping wind resources with high spatial resolution. Around 181 collected pairs of wind data from SAR wind maps and from 13 meteorological stations in Hangzhou Bay are compared. The statistical results comparing in situ wind speed and SAR-based wind speed show a standard deviation (SD of 1.99 m/s and correlation coefficient of R = 0.67. The model wind directions, which are used as input for the SAR wind speed retrieval, show a high correlation coefficient (R = 0.89 but a large standard deviation (SD = 42.3° compared to in situ observations. The Weibull probability density functions are compared at one meteorological station. The SAR-based results appear not to estimate the mean wind speed, Weibull scale and shape parameters and wind power density from the full in situ data set so well due to the lower number of satellite samples. Distributions calculated from the concurrent 81 SAR and in situ samples agree well.

NORSEWInD satellite wind climatology

DEFF Research Database (Denmark)

Hasager, Charlotte Bay; Badger, Merete; Mouche, Alexis

The EU-NORSEWInD project www.norsewind.eu has taken place from August 2008 to July 2012 (4 years). NORSEWInD is short for Northern Seas Wind Index database. In the project ocean surface wind observations from space have been retrieved, processed and analysed. The overall aim of the work...... is to provide new offshore wind climatology map for the entire area of interest based on satellite remote sensing. This has been based on Synthetic Aperture Radar (SAR) from Envisat ASAR using 9000 scenes re-processed with ECMWF wind direction and CMOD-IFR. The number of overlapping samples range from 450...... in the Irish Sea to more than 1200 in most of the Baltic Sea. Wind resource statistics include maps at 2 km spatial resolution of mean wind speed, Weibull A and k, and energy density at 10 m above sea level. Uncertainty estimates on the number of available samples for each of the four parameters are presented...

Wind speed and direction shears with associated vertical motion during strong surface winds

Science.gov (United States)

Alexander, M. B.; Camp, D. W.

1984-01-01

Strong surface winds recorded at the NASA 150-Meter Ground Winds Tower facility at Kennedy Space Center, Florida, are analyzed to present occurrences representative of wind shear and vertical motion known to be hazardous to the ascent and descent of conventional aircraft and the Space Shuttle. Graphical (percentage frequency distributions) and mathematical (maximum, mean, standard deviation) descriptions of wind speed and direction shears and associated updrafts and downdrafts are included as functions of six vertical layers and one horizontal distance for twenty 5-second intervals of parameters sampled simultaneously at the rate of ten per second during a period of high surface winds.

Using Satellite SAR to Characterize the Wind Flow around Offshore Wind Farms

Directory of Open Access Journals (Sweden)

Charlotte Bay Hasager

2015-06-01

Full Text Available Offshore wind farm cluster effects between neighboring wind farms increase rapidly with the large-scale deployment of offshore wind turbines. The wind farm wakes observed from Synthetic Aperture Radar (SAR are sometimes visible and atmospheric and wake models are here shown to convincingly reproduce the observed very long wind farm wakes. The present study mainly focuses on wind farm wake climatology based on Envisat ASAR. The available SAR data archive covering the large offshore wind farms at Horns Rev has been used for geo-located wind farm wake studies. However, the results are difficult to interpret due to mainly three issues: the limited number of samples per wind directional sector, the coastal wind speed gradient, and oceanic bathymetry effects in the SAR retrievals. A new methodology is developed and presented. This method overcomes effectively the first issue and in most cases, but not always, the second. In the new method all wind field maps are rotated such that the wind is always coming from the same relative direction. By applying the new method to the SAR wind maps, mesoscale and microscale model wake aggregated wind-fields results are compared. The SAR-based findings strongly support the model results at Horns Rev 1.

Uso de fosfato para remoção de arsênio de solo contaminado Use of phosphate for removal of arsenic from contaminated soil

Directory of Open Access Journals (Sweden)

Waleska G. P. da Silva

2010-01-01

Full Text Available Quando da opção do procedimento de remediação de solos contaminados com metais pesados para determinado sítio, deve-se levar em consideração dados do sítio e do contaminante, o grau de contaminação, o uso futuro da área e a viabilidade econômica do processo de remediação. A Cia. Mercantil Ingá, localizada no município de Itaguaí, RJ, extraía zinco da calamina através do processo de hidrometalurgia. Durante 31 anos a empresa dispôs, no seu pátio e de forma inadequada, cerca de 3 milhões de toneladas de resíduo perigoso. Uma das etapas do processo de extração do zinco consistia na adição de trióxido de arsênio para a remoção de impurezas, tendo-se verificado contaminação do solo com arsênio de áreas próximas ao local de disposição do resíduo. Dentro deste contexto se avaliou, no presente estudo, a técnica de remediação ex situ, através da remoção por lavagem de solo contaminado com arsênio, e o tratamento do efluente gerado da lavagem. O fracionamento mostrou que a diminuição do pH aumentou a retenção do arsênio. O diidrogenofosfato de potássio 0,4 mol L-1 mostrou-se eficiente na remoção por dessorção do arsênio presente no solo contaminado, conseguindo dessorver cerca de 70% deste elemento em pH 6,2. O cloreto férrico foi mais eficiente que o sulfato de alumínio para a remoção por coagulação, do arsênio do efluente da lavagem do solo.Several remediation procedures for soils contaminated with heavy metals are based on decontamination or stabilization. The selection of one of them for a given site should take data regarding the site and the contaminating agent, contamination degree, future use of the site and the economic viability of remediation process into account. The Mercantil Ingá Company, located in the municipality of Itaguaí - RJ, Brazil, has extracted zinc from calamine through hydrometallurgy. During 31 years, the company improperly disposed of about three million tons of

Métodos de remoção da mucilagem e qualidade fisiológica de sementes de tomate (Lycopersicon esculentum, Mill. Methods of mucilage remotion and physiological quality of tomato (Lycopersicon sculentum Mill. seeds

Directory of Open Access Journals (Sweden)

C. Cavariani

1994-04-01

Full Text Available Objetivando estudar diferentes métodos de remoção da mucilagem e a qualidade de sementes de tomate (Lycopersicon esculentum Mill., conduziu-se um experimento, em delineamento inteiramente casualizado com quatro repetições. Após extração manual, sementes e mucilagens foram submetidas aos seguintes tratamentos de remoção: lavagem imediata, fermentação por três dias, ácido clorídrico a 2,5% (25 ml/kg, durante 2 horas, ácido acético a 10% (25 ml/kg de material e hidróxido de amônia a 2,5% (25 ml/kg, durante 2 horas. Seguiu-se a avaliação da qualidade fisiológica das sementes através das determinações de porcentagem de germinação e vigor, pela porcentagem de emergência em areia, condutividade elétrica e pesos das matérias verde e seca de plântulas. Os resultados permitiram concluir que os métodos de remoção por lavagem imediata, fermentação, ácido clorídrico e ácido acético comercial não afetaram a qualidade fisiológica de sementes de tomate; a porcentagem de germinação não foi afetada pelos diferentes métodos de remoção e o método hidróxido de amônia prejudica o vigor das sementes.Different methods of mucilage remotion and quality of tomato (Lycopersicon esculentum Mill. seeds were studied, in a complete randomized design experiment with four replications. After manual extraction, seeds and slimes were submitted to the following remotion treatments: immediate washing, three-day fermentation, hydrochloric acid at 2,5% (25 mg/kg for 2 hrs., acetic acid at 10% (25 ml/kg of material, and ammonia hydroxide at 2,5% (25 ml/kg, for 2 hrs.. A physiological quality evaluation of seeds was carried out through the percentage of germination and vigor, percentage of in-sand emergence, electrical conductivity, and weight of fresh and dry matters of seedlings. The results showed that the methods of immediate washing, fermentation, commercial hydrochloric and acetic acids do not affect the physiological quality of

Vector wind and vector wind shear models 0 to 27 km altitude for Cape Kennedy, Florida, and Vandenberg AFB, California

Science.gov (United States)

Smith, O. E.

1976-01-01

The techniques are presented to derive several statistical wind models. The techniques are from the properties of the multivariate normal probability function. Assuming that the winds can be considered as bivariate normally distributed, then (1) the wind components and conditional wind components are univariate normally distributed, (2) the wind speed is Rayleigh distributed, (3) the conditional distribution of wind speed given a wind direction is Rayleigh distributed, and (4) the frequency of wind direction can be derived. All of these distributions are derived from the 5-sample parameter of wind for the bivariate normal distribution. By further assuming that the winds at two altitudes are quadravariate normally distributed, then the vector wind shear is bivariate normally distributed and the modulus of the vector wind shear is Rayleigh distributed. The conditional probability of wind component shears given a wind component is normally distributed. Examples of these and other properties of the multivariate normal probability distribution function as applied to Cape Kennedy, Florida, and Vandenberg AFB, California, wind data samples are given. A technique to develop a synthetic vector wind profile model of interest to aerospace vehicle applications is presented.

Remoção de substâncias húmicas por meio da oxidação com ozônio e peróxido de hidrogênio e FiME Removal of humic substances by means of oxidation with ozone and hydrogen peroxide and FiME

Directory of Open Access Journals (Sweden)

Edson Pereira Tangerino

2005-12-01

Full Text Available A filtração em múltiplas etapas (FiME se apresenta como uma alternativa para realizar o tratamento de água de comunidades de pequeno porte, entretanto, a eficiência quanto à remoção de cor verdadeira associada ao carbono orgânico dissolvido (COD ou às substâncias húmicas, tem sido questionada ou relatada como baixa. A presente pesquisa avaliou a remoção de substâncias húmicas na FiME com pré-oxidação, com ozônio e peróxido de hidrogênio, utilizando para essa avaliação parâmetros indiretos como cor verdadeira, absorvância UV (254 nm e COD. Foram realizados cinco ensaios, utilizando quatro filtros lentos, sendo dois com camada de carvão ativado granular (CAG. Foram ensaiadas várias alternativas de pré-oxidação com ozônio e peróxido de hidrogênio. Foram obtidos bons resultados, tendo como principal conclusão que os filtros lentos com CAG, precedidos de oxidação com ozônio e depois peróxido de hidrogênio, apresentaram remoção média de cor verdadeira de 64%, mas que o peróxido de hidrogênio afeta o desenvolvimento da camada biológica, interferindo no desenvolvimento da perda de carga, na remoção de turbidez, na remoção de coliformes e na remoção de substâncias húmicas.The multistage filtration (FiME is an alternative to accomplish water treatment for small communities, however, as for removal of true color associated to dissolved organic carbon (DOC or humic substances, it have been questioned or reported as low efficiency. The present research evaluated the removal of humic substances in the FiME using ozone and hydrogen peroxide as a pre-oxidation, using for this indirect parameters how true color, UV absorbance (254nm and DOC. Five experiments were conducted using four slow filters, from this two were composed the intermediate layer of granulate activated carbon (GAC. The assays were conducted with pre-oxidation alternatives using ozone and hydrogen peroxide in several applications forms. It

In-plain electric properties of [CaMnO3/REMO3] (RE=Bi, La M=Fe, Fe0.8Mn0.2) superlattices grown by pulsed laser deposition method

NARCIS (Netherlands)

Iwata, N.; Watabe, Y.; Oikawa, T.; Takase, K.; Huijben, Mark; Inaba, T.; Oshima, K.; Rijnders, Augustinus J.H.M.; Yamamoto, H.

2014-01-01

The [CaMnO3 (CMO)/REMO3] (RE = Bi, La M = Fe, Fe0.8Mn0.2) superlattices show semiconducting behavior with transition temperatures (TEg) of 71, 127, and 151 K in the [CMO/BiFe0.8Mn0.2O3], [CMO/BiFeO3], and [CMO/LaFeO3] superlattices. The formation of a magnetic polaron is expected in the CMO layer of

ISOTOPIC MASS FRACTIONATION OF SOLAR WIND: EVIDENCE FROM FAST AND SLOW SOLAR WIND COLLECTED BY THE GENESIS MISSION

International Nuclear Information System (INIS)

Heber, Veronika S.; Baur, Heinrich; Wieler, Rainer; Bochsler, Peter; McKeegan, Kevin D.; Neugebauer, Marcia; Reisenfeld, Daniel B.; Wiens, Roger C.

2012-01-01

NASA's Genesis space mission returned samples of solar wind collected over ∼2.3 years. We present elemental and isotopic compositions of He, Ne, and Ar analyzed in diamond-like carbon targets from the slow and fast solar wind collectors to investigate isotopic fractionation processes during solar wind formation. The solar wind provides information on the isotopic composition for most volatile elements for the solar atmosphere, the bulk Sun and hence, on the solar nebula from which it formed 4.6 Ga ago. Our data reveal a heavy isotope depletion in the slow solar wind compared to the fast wind composition by 63.1 ± 2.1 per mille for He, 4.2 ± 0.5 per mille amu –1 for Ne and 2.6 ± 0.5 per mille amu –1 for Ar. The three Ne isotopes suggest that isotopic fractionation processes between fast and slow solar wind are mass dependent. The He/H ratios of the collected slow and fast solar wind samples are 0.0344 and 0.0406, respectively. The inefficient Coulomb drag model reproduces the measured isotopic fractionation between fast and slow wind. Therefore, we apply this model to infer the photospheric isotopic composition of He, Ne, and Ar from our solar wind data. We also compare the isotopic composition of oxygen and nitrogen measured in the solar wind with values of early solar system condensates, probably representing solar nebula composition. We interpret the differences between these samples as being due to isotopic fractionation during solar wind formation. For both elements, the magnitude and sign of the observed differences are in good agreement with the values predicted by the inefficient Coulomb drag model.

ISOTOPIC MASS FRACTIONATION OF SOLAR WIND: EVIDENCE FROM FAST AND SLOW SOLAR WIND COLLECTED BY THE GENESIS MISSION

Energy Technology Data Exchange (ETDEWEB)

Heber, Veronika S.; Baur, Heinrich; Wieler, Rainer [Institute for Geochemistry and Petrology, ETH Zurich, Clausiusstrasse 25, CH-8092 Zurich (Switzerland); Bochsler, Peter [Physikalisches Institut, Universitaet Bern, Sidlerstasse 5, CH-3012 Bern (Switzerland); McKeegan, Kevin D. [Department of Earth and Space Sciences, University of California Los Angeles, 595 Charles Young Drive East, Box 951567, Los Angeles, CA 90095-1567 (United States); Neugebauer, Marcia [Lunar and Planetary Laboratory, University of Arizona, Tucson, AZ 85721-0092 (United States); Reisenfeld, Daniel B. [Department of Physics and Astronomy, University of Montana, Missoula, MT 59812 (United States); Wiens, Roger C., E-mail: heber@ess.ucla.edu [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

2012-11-10

NASA's Genesis space mission returned samples of solar wind collected over {approx}2.3 years. We present elemental and isotopic compositions of He, Ne, and Ar analyzed in diamond-like carbon targets from the slow and fast solar wind collectors to investigate isotopic fractionation processes during solar wind formation. The solar wind provides information on the isotopic composition for most volatile elements for the solar atmosphere, the bulk Sun and hence, on the solar nebula from which it formed 4.6 Ga ago. Our data reveal a heavy isotope depletion in the slow solar wind compared to the fast wind composition by 63.1 {+-} 2.1 per mille for He, 4.2 {+-} 0.5 per mille amu{sup -1} for Ne and 2.6 {+-} 0.5 per mille amu{sup -1} for Ar. The three Ne isotopes suggest that isotopic fractionation processes between fast and slow solar wind are mass dependent. The He/H ratios of the collected slow and fast solar wind samples are 0.0344 and 0.0406, respectively. The inefficient Coulomb drag model reproduces the measured isotopic fractionation between fast and slow wind. Therefore, we apply this model to infer the photospheric isotopic composition of He, Ne, and Ar from our solar wind data. We also compare the isotopic composition of oxygen and nitrogen measured in the solar wind with values of early solar system condensates, probably representing solar nebula composition. We interpret the differences between these samples as being due to isotopic fractionation during solar wind formation. For both elements, the magnitude and sign of the observed differences are in good agreement with the values predicted by the inefficient Coulomb drag model.

CubeSat Constellation Cloud Winds(C3Winds) A New Wind Observing System to Study Mesoscale Cloud Dynamics and Processes

Science.gov (United States)

Wu, D. L.; Kelly, M.A.; Yee, J.-H.; Boldt, J.; Demajistre, R.; Reynolds, E. L.; Tripoli, G. J.; Oman, L. D.; Prive, N.; Heidinger, A. K.;

Síntese e caracterização de compósito magnético nanoestruturado contendo óxido de manganês para remoção de íons Cd(II do meio aquoso

Directory of Open Access Journals (Sweden)

A. P. Heitmann

2014-09-01

Full Text Available O tratamento de efluentes contendo cádmio é de grande interesse devido à persistência desse contaminante no meio ambiente e às graves doenças que pode causar ao homem. No presente trabalho, foi utilizado o compósito magnético Mn3O4/Fe3O4 como adsorvente do íon cádmio (II em meio aquoso. O material adsorvente foi sintetizado e caracterizado segundo as técnicas de difração de raios X (DRX, espectroscopia Raman, microscopia eletrônica de transmissão e sorção de N2 (BET. Ênfase foi dada à quantificação das fases do compósito pela análise de DRX combinada ao método Rietveld. O estudo de adsorção foi realizado variando o pH do meio e a concentração do íon cádmio em solução. A análise dos resultados possibilitou verificar que a remoção de Cd(II utilizando compósito magnético Mn3O4/Fe3O4 em meio aquoso é dependente do pH duplicando a medida que o pH varia de 3 para 7. O estudo de imobilização do íon contaminante em solução apresentou valores significativos de capacidade máxima de adsorção, de 12,3 mgCd/g no pH 6 e 13,6 mgCd/g no pH 7, indicando uma remoção de até 98% para concentrações baixas do íon, sugerindo que o adsorvente apresenta elevado potencial para remoção de Cd(II em meio aquoso.

The social acceptability of wind turbines: some resident are ready to pay to keep their wind turbines. Survey on four French wind farms

International Nuclear Information System (INIS)

2009-06-01

The authors report a study which aimed at exploiting and deepening the results of a 2001 survey on visual and sound disturbances caused by wind turbines in Sigean (Aude), at identifying all the attitudes and opinions with respect with wind energy, and at assessing the different characteristics of a wind farm (height, localization, and so on). A survey has been performed on four sites located in different French regions. The authors discuss the social-demographic characteristics of the population samples, the global opinion on wind energy, and the opinion of the people on wind turbines located in their neighbourhood. They propose an estimation of benefits and damages related to the vicinity of wind turbines. By applying a method of choice experiments, they reveal the preferences of residents

Conjunto de ejercicios para mejorar la ejecución técnica del equipo de remo categoría 13-15 masculino de la provincia Artemisa

Directory of Open Access Journals (Sweden)

Rubén Sarduy Jorge

2011-09-01

Full Text Available La preparación técnica es uno de los componentes de la preparación deportiva y es fundamental en el rendimiento deportivo de cualquiera de los deportes. En el remo es uno de los factores que inciden en el rendimiento deportivo de los remeros. Por esta razón los entrenadores de remo evalúan sistemáticamente el estado técnico de sus atletas; sin embargo, estos presentan aún errores fundamentales y secundarios en su ejecución, como es el caso de los remeros de la categoría 13-15 años de la provincia Artemisa. Para darle solución a esta situación se propone un conjunto de ejercicios para mejorar la ejecución de la técnica de estos atletas, fundamentados en la concepción de Chuter, Nilsen y Postiglione (2008. La propuesta se basa en ejercicios para el dominio del bote como medio fundamental de este deporte y ejercicios para mejorar la ejecución de la técnica, equilibrio y coordinación, los que constituyen elementos esenciales en estas categorías. Los ejercicios se sometieron a la valoración de especialistas los que evaluaron de Bien la propuesta y la consideraron de importancia para el trabajo de los entrenadores en la preparación de sus atletas.

Applicability of Synthetic Aperture Radar Wind Retrievals on Offshore Wind Resources Assessment in Hangzhou Bay, China

DEFF Research Database (Denmark)

Chang, Rui; Zhu, Rong; Badger, Merete

2014-01-01

In view of the high cost and sparse spatial resolution of offshore meteorological observations, ocean winds retrieved from satellites are valuable in offshore wind resource assessment as a supplement to in situ measurements. This study examines satellite synthetic aperture radar (SAR) images from...... ENVISAT advanced SAR (ASAR) for mapping wind resources with high spatial resolution. Around 181 collected pairs of wind data from SAR wind maps and from 13 meteorological stations in Hangzhou Bay are compared. The statistical results comparing in situ wind speed and SAR-based wind speed show a standard...... density functions are compared at one meteorological station. The SAR-based results appear not to estimate the mean wind speed, Weibull scale and shape parameters and wind power density from the full in situ data set so well due to the lower number of satellite samples. Distributions calculated from...

Effect of wind on Svalbard reindeer fur insulation

Directory of Open Access Journals (Sweden)

Christine Cuyler

2002-06-01

Full Text Available The heat transfer through Svalbard reindeer (Rangifer tarandus platyrhynchus fur samples was studied with respect to wind velocity, season and animal age. A total of 33 dorsal fur sections were investigated using a wind tunnel. Insulation varied with season (calving, summer, autumn and winter. At zero wind velocity, fur insulation was significantly different between seasons for both calf and adult fur samples. At the same time, there was no significant difference between calf and adult insulation for the summer, autumn and winter seasons. Calf fur insulated as well as adult fur. Winter insulation of Svalbard reindeer was approximately 3 times that of summer. Increasing wind veloci¬ty increased heat loss, however, the increase was not dramatic. When wind coefficients (slope of the heat transfer regression lines were compared, between season and between calf and adult, no significant differences were reported. All fur samples showed similar increases in heat transfer for wind velocities between 0 and 10 m.s-1. The conductance of winter fur of Svalbard reindeer was almost half that of caribou fur. Also, conductance was not as greatly influenced by wind as caribou fur

Genesis Solar Wind Collector Cleaning Assessment: Update on 60336 Sample Case Study

Science.gov (United States)

Goreva, Y. S.; Allums, K. K.; Gonzalez, C. P.; Jurewicz, A. J.; Burnett, D. S.; Allton, J. H.; Kuhlman, K. R.; Woolum, D.

2015-01-01

To maximize the scientific return of Genesis Solar Wind return mission it is necessary to characterize and remove a crash-derived particle and thin film surface contamination. A small subset of Genesis mission collector fragments are being subjected to extensive study via various techniques. Here we present an update on the sample 60336, a Czochralski silicon (Si-CZ) based wafer from the bulk array (B/C). This sample has undergone multiple cleaning steps (see the table below): UPW spin wash, aggressive chemical cleanings (including aqua regia, hot xylene and RCA1), as well as optical and chemical (EDS, ToF-SIMS) imaging. Contamination appeared on the surface of 60336 after the initial 2007 UPW cleaning. Aqua regia and hot xylene treatment (8/13/2013) did little to remove contaminants. The sample was UPW cleaned for the third time and imaged (9/16/13). The UPW removed the dark stains that were visible on the sample. However, some features, like "the Flounder" (a large, 100 micron feature in Fig. 1b) appeared largely intact, resisting all previous cleaning efforts. These features were likely from mobilized adhesive, derived from the Post-It notes used to stabilize samples for transport from Utah after the hard landing. To remove this contamination, an RCA step 1 organic cleaning (RCA1) was employed. Although we are still uncertain on the nature of the Flounder and why it is resistant to UPW and aqua regia/hot xylene treatment, we have found RCA1 to be suitable for its removal. It is likely that the glue from sticky pads used during collector recovery may have been a source for resistant organic contamination [9]; however [8] shows that UPW reaction with crash-derived organic contamination does not make particle removal more difficult.

Visual disamenities from off-shore wind farms in Denmark

DEFF Research Database (Denmark)

Ladenburg, Jacob; Dubgaard, Alex; Tranberg, Jesper

2006-01-01

Expansion of the off-shore wind power plays a significant role in the energy policies of many EU countries. However, off-shore wind farms create visual disamenities. These disamenities can be reduced by locating wind farms at larger distances from the coast – and accepting higher costs per k......Wh produced. Base on the choices among alternative wind farm outlays, the preferences for reducing visual disamenities of off-shore wind farms were elicited using the Choice Experiment Method. The results show a clear picture; the respondents in three independent samples are willing to pay for mowing future...... off-shore wind farms away from the shore to reduce the wind farms visibility. However, the results also denote that the preferences vary with regards to the experiences with visual disamenities of off-shore wind farms. The respondents Horns Revs sample, where the off-shore wind farm is located...

Estudo comparativo do rendimento de dois tipos de pás de remo e da técnica da remada em barco "skiff"

OpenAIRE

Adriana Marques Toigo

1999-01-01

O presente trabalho teve como objetivo estudar a eficiência na aplicação de força a um barco “skiff” com dois tipos de pás de remo (“standard” e cutelo) e verificar se a utilização desses dois tipos de pás produziam alterações na técnica da remada. Um barco “skiff” foi preso por seis cabos de aço às bordas de uma piscina coberta. Um dinamômetro foi instalado a um destes cabos para coletar os dados de força, enquanto a técnica da remada foi estudada por meio de um sistema de cinemetria. A amos...

Measurement of volatile organic compounds during start-up of bioremediation of French limited superfund site in Crosby Texas using wind dependent whole-air sampling

International Nuclear Information System (INIS)

Pleil, J.D.; Fortune, C.R.; Yoong, M.; Oliver, K.D.

1993-01-01

Whole-air sampling was performed before and after the start-up of the bioremediation of an industrial (primarily petrochemical) waste lagoon in Crosby Texas, near Houston. Four 'Sector Samplers' were deployed at the four corners of the French Limited Superfund Site. These samplers collect air into one of two SUMMA polished canisters depending upon wind direction and speed. When the wind blows at the sampler from across the waste lagoon, air is routed to the 'IN' sector canister, otherwise sample is collected in the 'OUT' sector canister. As such, each sampler provides its own background sample, and, upon gas chromatographic analysis, individual compounds can be associated with the waste lagoon. Five sets of 24-hour sector samples were taken; the first set was collected prior to the start of the bioremediation effort and the remaining four sets were taken sequentially for four 24-hour periods after the start-up of the procedure

Scheduling whole-air samples above the Trade Wind Inversion from SUAS using real-time sensors

Science.gov (United States)

Freer, J. E.; Greatwood, C.; Thomas, R.; Richardson, T.; Brownlow, R.; Lowry, D.; MacKenzie, A. R.; Nisbet, E. G.

2015-12-01

Small Unmanned Air Systems (SUAS) are increasingly being used in science applications for a range of applications. Here we explore their use to schedule the sampling of air masses up to 2.5km above ground using computer controlled bespoked Octocopter platforms. Whole-air sampling is targeted above, within and below the Trade Wind Inversion (TWI). On-board sensors profiled the TWI characteristics in real time on ascent and, hence, guided the altitudes at which samples were taken on descent. The science driver for this research is investigation of the Southern Methane Anomaly and, more broadly, the hemispheric-scale transport of long-lived atmospheric tracers in the remote troposphere. Here we focus on the practical application of SUAS for this purpose. Highlighting the need for mission planning, computer control, onboard sensors and logistics in deploying such technologies for out of line-of-sight applications. We show how such a platform can be deployed successfully, resulting in some 60 sampling flights within a 10 day period. Challenges remain regarding the deployment of such platforms routinely and cost-effectively, particularly regarding training and support. We present some initial results from the methane sampling and its implication for exploring and understanding the Southern Methane Anomaly.

Efeito de diferentes métodos de recuperação sobre a remoção de lactato e desempenho anaeróbio de futebolistas

Directory of Open Access Journals (Sweden)

Homero Gustavo Ferrari

2013-12-01

Full Text Available INTRODUÇÃO: O futebol é caracterizado como uma modalidade com intensidades elevadas, realizado de forma intermitente e com sequências aleatórias de fases de esforço e recuperação, dessa forma estratégias que possam de alguma forma minimizar a fadiga muscular, pode fornecer uma importante vantagem competitiva. OBJETIVO: O presente estudo teve como objetivo comparar diferentes tipos de métodos de recuperação sobre remoção de lactato (La- sanguíneo e desempenho anaeróbio de futebolistas. MÉTODOS: A amostra foi composta por 23 atletas de futebol entre 16 e 17 anos do sexo masculino, divididos em três grupos: recuperação ativa (RA, passiva (RP e com gelo (RG. Para a avaliação da capacidade aeróbia foi utilizada a velocidade crítica e para a indução da hiperlactacidemia e desempenho anaeróbio foi utilizando o teste de RAST, aplicado antes (T1 e após (T2 os intervalos de recuperação. As dosagens de La- sanguíneo ocorreram nos minutos dois, quatro, seis, oito e 10 durante a recuperação. A análise de variância ANOVA one-way foi utilizada para a comparação entre as variáveis de caracterização dos grupos. A ANOVA two-way foi realizada para a comparação entre os valores pico e mínimo de La- sanguíneo e o desempenho anaeróbio no T1 e T2 para as três condições de recuperação. RESULTADOS: Não foi verificada diferença significante entre T1 e T2 para a potência máxima e média em nenhum dos grupos estudados (p > 0,05. Foi verificada maior remoção do La- sanguíneo para a RA (47,62%, quando comparada a RG (16,9%; p = 0,001 e a RP (18,20%; p = 0,02. CONCLUSÃO: Pode-se concluir que a RA, RP e RG são eficazes para manutenção do desempenho anaeróbio de jogadores de futebol sub-17. A recuperação ativa se demonstrou mais eficiente para a remoção do La- sanguíneo quando comparada a RP e RG.

Efeito da taxa de carregamento sobre a remoção de poluentes de esgoto em sistemas alagados construídos Effect of loading rate on removal of pollutants from wastewater in constructed wetlands

Directory of Open Access Journals (Sweden)

Antonio T. de Matos

2013-04-01

Full Text Available Objetivou-se estudar o efeito da taxa de carregamento sobre a eficiência de sistemas alagados, construídos de escoamento horizontal subsuperficial (SAC-EHSS, em remover poluentes de esgoto sanitário. Os SAC-EHSS foram alimentados com efluente proveniente de tanque séptico, sob taxas de carregamento orgânico volumétrico (TCO V de 53 a 231 g m-3d-1 de demanda química de oxigênio (DQO total e as associadas taxas de carregamento (TC V de demanda química de oxigênio solúvel, sólidos suspensos totais (SST, nitrogênio total (N-Total e fósforo total (P-Total. Para avaliação de desempenho dos SAC-EHSS, as mesmas variáveis foram quantificadas em seu efluente. Relação linear e positiva foi obtida entre as taxas de remoção de DQO total, DQO solúvel e SST, e as TC V, nas faixas em que foram aplicadas, além de não terem sido observados efeitos negativos desta variável sobre a eficiência na remoção desses poluentes. As taxas de remoção de N-Total e P-Total não apresentaram, entretanto, tendência de aumento com a TC V aplicada nos SAC- EHSS, cultivados com taboa e utilizados no tratamento de efluente sanitário. As cargas aplicadas desses nutrientes devem ser consideradas referenciais no dimensionamento desses sistemas, caso se queira maximizar a remoção global de poluentes da água residuária.This research aimed to study the effect of loading rate on the efficiency of constructed wetlands with horizontal subsurface flow (CW-HSSF to remove pollutants from wastewater. The CW-HSSF were fed with effluent from septic tank under volumetric organic loading rate (OLR V of 53 to 231 g m-3d-1 of chemical oxygen demand (total-COD and associated loading rates (LR V of soluble chemical oxygen demand (soluble COD, total suspended solids (TSS, total nitrogen (total-N and total phosphorus (total-P. To evaluate the performance of CW-HSSF the same variables were quantified in its effluent. Linear and positive relationship was found between the

Remoção de sólidos em suspensão na água residuária da despolpa de frutos do cafeeiro em filtros constituídos por pergaminho de grãos de café submetido a compressões Removal of suspended solids in the wastewater of the coffee shrub cherry pulping by filters constituted by parchment of the coffee beans subjected to compressions

Directory of Open Access Journals (Sweden)

Antonio T. de Matos

2006-08-01

Full Text Available A remoção de sólidos em suspensão é fundamental para que se possa aplicar a água residuária gerada na despolpa de frutos do cafeeiro (ARC na fertirrigação de culturas agrícolas. Dentre as opções disponíveis para efetuar a remoção de SS da ARC, está o uso de filtros orgânicos. Este trabalho foi desenvolvido com o objetivo de avaliar a influência do grau de compressão na redução do volume e na eficiência do pergaminho, utilizado como material filtrante, na remoção de sólidos em suspensão (SS na ARC. Numa primeira etapa, foram realizados ensaios nos quais corpos-de-prova de pergaminho triturado (retido entre as peneiras de 2,5 e 3 mm e não-triturado (na condição em que é produzido foram submetidos a diferentes compressões para a redução do volume das colunas filtrantes em 5; 10; 15; 20; 25 e 28%. Numa segunda etapa, os corpos-de-prova foram utilizados como material filtrante da ARC para a avaliação da sua capacidade de remoção de SS presentes nessa água residuária. O pergaminho triturado ofereceu maior resistência à compressão e proporcionou, para as mesmas reduções volumétricas no material filtrante, maior eficiência na remoção de SS da ARC do que o pergaminho não-triturado. Reduções na faixa de 10% a 15% no volume do filtro constituído por pergaminho triturado foram suficientes para obter satisfatórias eficiências na remoção de SS da ARC, enquanto, para filtros constituídos de pergaminho não-triturado, as reduções de volume devem ser superiores a 25%.The removal of suspended solids (SS is fundamental to apply the wastewater from the coffee shrub cherry pulping (ARC on agricultural crops fertigation. Among the available options for the removal of SS from ARC is the use of organic filters. This study was carried out to evaluate the influence of the compression degree on either volume reduction or parchment efficiency, when used as medium filter for the removal of suspended solids (SS in

High-Resolution Wind Measurements for Offshore Wind Energy Development

Science.gov (United States)

Nghiem, Son V.; Neumann, Gregory

2011-01-01

A mathematical transform, called the Rosette Transform, together with a new method, called the Dense Sampling Method, have been developed. The Rosette Transform is invented to apply to both the mean part and the fluctuating part of a targeted radar signature using the Dense Sampling Method to construct the data in a high-resolution grid at 1-km posting for wind measurements over water surfaces such as oceans or lakes.

The solar wind in time: a change in the behaviour of older winds?

Science.gov (United States)

O'Fionnagáin, D.; Vidotto, A. A.

2018-05-01

In this paper, we model the wind of solar analogues at different ages to investigate the evolution of the solar wind. Recently, it has been suggested that winds of solar type stars might undergo a change in properties at old ages, whereby stars older than the Sun would be less efficient in carrying away angular momentum than what was traditionally believed. Adding to this, recent observations suggest that old solar-type stars show a break in coronal properties, with a steeper decay in X-ray luminosities and temperatures at older ages. We use these X-ray observations to constrain the thermal acceleration of winds of solar analogues. Our sample is based on the stars from the `Sun in Time' project with ages between 120 and 7000 Myr. The break in X-ray properties leads to a break in wind mass-loss rates (\\dot{M}) at roughly 2 Gyr, with \\dot{M} (t 2 Gyr) ∝ t-3.9. This steep decay in \\dot{M} at older ages could be the reason why older stars are less efficient at carrying away angular momentum, which would explain the anomalously rapid rotation observed in older stars. We also show that none of the stars in our sample would have winds dense enough to produce thermal emission above 1-2 GHz, explaining why their radio emissions have not yet been detected. Combining our models with dynamo evolution models for the magnetic field of the Earth, we find that, at early ages (≈100 Myr), our Earth had a magnetosphere that was three or more times smaller than its current size.

Global sensitivity analysis in wind energy assessment

Science.gov (United States)

Tsvetkova, O.; Ouarda, T. B.

2012-12-01

Wind energy is one of the most promising renewable energy sources. Nevertheless, it is not yet a common source of energy, although there is enough wind potential to supply world's energy demand. One of the most prominent obstacles on the way of employing wind energy is the uncertainty associated with wind energy assessment. Global sensitivity analysis (SA) studies how the variation of input parameters in an abstract model effects the variation of the variable of interest or the output variable. It also provides ways to calculate explicit measures of importance of input variables (first order and total effect sensitivity indices) in regard to influence on the variation of the output variable. Two methods of determining the above mentioned indices were applied and compared: the brute force method and the best practice estimation procedure In this study a methodology for conducting global SA of wind energy assessment at a planning stage is proposed. Three sampling strategies which are a part of SA procedure were compared: sampling based on Sobol' sequences (SBSS), Latin hypercube sampling (LHS) and pseudo-random sampling (PRS). A case study of Masdar City, a showcase of sustainable living in the UAE, is used to exemplify application of the proposed methodology. Sources of uncertainty in wind energy assessment are very diverse. In the case study the following were identified as uncertain input parameters: the Weibull shape parameter, the Weibull scale parameter, availability of a wind turbine, lifetime of a turbine, air density, electrical losses, blade losses, ineffective time losses. Ineffective time losses are defined as losses during the time when the actual wind speed is lower than the cut-in speed or higher than the cut-out speed. The output variable in the case study is the lifetime energy production. Most influential factors for lifetime energy production are identified with the ranking of the total effect sensitivity indices. The results of the present

Caracterização da argila bentonítica para utilização na remoção de chumbo de efluentes sintéticos Characterization of smectite clays for application in the removal of lead from synthetic effluents

Directory of Open Access Journals (Sweden)

M. G. F. Rodrigues

2004-09-01

Full Text Available Este artigo tem como principal objetivo caracterizar argilas esmectíticas chocolate de Boa-Vista, Estado da Paraíba (Brasil na sua forma natural e após tratamento químico, visando a sua utilização na remoção de Pb2+ de efluentes sintéticos. Os métodos de caracterização utilizados foram fluorescência de raios X, difração de raios X, microscopia eletrônica de varredura e espectroscopia de raios X por energia dispersiva. Neste trabalho foi estabelecido o procedimento para remoção de Pb2+ a partir de um efluente inorgânico sintético, utilizando argila natural. Para avaliar a influência dos principais parâmetros, como pH, tratamento e granulometria da argila sobre a remoção do Pb2+, foi utilizado o planejamento fatorial e os melhores resultados obtidos foram: pH 4,5, granulometria entre 35 e 48 mesh, e argila natural.The main objective of this paper is to characterize the Chocolate smectite clays of Boa-Vista, State of Paraíba (Brazil, in their natural form, and after chemical treatment for their application in the removal of Pb2+ from synthetic effluents. The following methods were used: X-ray fluorescence, X-ray diffraction, scanning electron microscopy and energy dispersive X-ray spectroscopy. In is work the procedures for Pb2+ removal from a synthetic inorganic effluent using a natural clay were established. To evaluate the influence of the main parameters, such as pH, clay treatment and granulometry, on Pb2+ removal, factorial planning was used and the best results obtained were pH 4.5, granulometry in the range of 35 to 48 mesh and natural clay.

Influência da velocidade no torque de remoção de tampas plásticas rosqueáveis para produtos farmacêuticos

Directory of Open Access Journals (Sweden)

Sandra Balan Mendoza Jaime

2012-04-01

Full Text Available O estudo teve por objetivo avaliar a influência da velocidade empregada durante a determinação do torque de aplicação e remoção de tampas plásticas rosqueáveis de polipropileno (PP, com vedante interno, aplicadas em frascos de vidro e de poli(tereftalato de etileno (PET para produtos farmacêuticos, com diâmetros de terminação de 24 e 28 mm. Foi verificada também a influência do material de embalagem (vidro ou PET e do diâmetro da terminação no torque de retenção estático e dinâmico (após simulação de transporte em intervalos de tempo após 24 e 48 horas e após 7, 14 e 28 dias da aplicação dos respectivos sistemas de fechamento. Verificou-se que a velocidade não apresenta influência no torque de aplicação desde que o valor máximo seja controlado durante o processo de fechamento da tampa. No torque de remoção imediato, entretanto, a velocidade influencia significativamente nos resultados, sendo recomendado, sempre que possível, a utilização de uma velocidade constante. Foi estabelecido para o estudo a velocidade de 5 rpm para evitar a influência desse parâmetro nos resultados de torque obtidos. O material de embalagem e o diâmetro da terminação evidenciaram influência significativa nos resultados de torque de retenção estático e dinâmico, sendo observados valores superiores para os frascos de vidro comparativamente aos frascos de PET. Esse desempenho pode estar associado às diferenças nas propriedades viscoelásticas e na força de fricção ou atrito entre os materiais da tampa com vedante e a embalagem.

Validation of odor concentration from mechanical-biological treatment piles using static chamber and wind tunnel with different wind speed values.

Science.gov (United States)

Szyłak-Szydłowski, Mirosław

2017-09-01

The basic principle of odor sampling from surface sources is based primarily on the amount of air obtained from a specific area of the ground, which acts as a source of malodorous compounds. Wind tunnels and flux chambers are often the only available, direct method of evaluating the odor fluxes from small area sources. There are currently no widely accepted chamber-based methods; thus, there is still a need for standardization of these methods to ensure accuracy and comparability. Previous research has established that there is a significant difference between the odor concentration values obtained using the Lindvall chamber and those obtained by a dynamic flow chamber. Thus, the present study compares sampling methods using a streaming chamber modeled on the Lindvall cover (using different wind speeds), a static chamber, and a direct sampling method without any screens. The volumes of chambers in the current work were similar, ~0.08 m 3 . This study was conducted at the mechanical-biological treatment plant in Poland. Samples were taken from a pile covered by the membrane. Measured odor concentration values were between 2 and 150 ou E /m 3 . Results of the study demonstrated that both chambers can be used interchangeably in the following conditions: odor concentration is below 60 ou E /m 3 , wind speed inside the Lindvall chamber is below 0.2 m/sec, and a flow value is below 0.011 m 3 /sec. Increasing the wind speed above the aforementioned value results in significant differences in the results obtained between those methods. In all experiments, the results of the concentration of odor in the samples using the static chamber were consistently higher than those from the samples measured in the Lindvall chamber. Lastly, the results of experiments were employed to determine a model function of the relationship between wind speed and odor concentration values. Several researchers wrote that there are no widely accepted chamber-based methods. Also, there is still a

Database on wind characteristics. Contents of database bank

DEFF Research Database (Denmark)

Larsen, Gunner Chr.; Hansen, K.S.

2001-01-01

for the available data in the established database bank and part three is the Users Manual describing the various ways to access and analyse the data. The present report constitutes the second part of the Annex XVII reporting. Basically, the database bank contains three categories of data, i.e. i) high sampled wind...... field time series; ii) high sampled wind turbine structural response time series; andiii) wind resource data. The main emphasis, however, is on category i). The available data, within each of the three categories, are described in details. The description embraces site characteristics, terrain type...

The Skipheia Wind Measurement Station. Instrumentation, Wind Speed Profiles and Turbulence Spectra

Energy Technology Data Exchange (ETDEWEB)

Aasen, S E

1995-10-01

This thesis describes the design of a measurement station for turbulent wind and presents results from an analysis of the collected data. The station is located at Skipheia near the south-west end of Froeya, an island off the coast of Mid-Norway. The station is unique for studies of turbulent winds because of the large numbers of sensors, which are located at various heights above ground up to 100 m, a sampling rate of 0.85 Hz and storage of the complete time series. The frequency of lightning and atmospheric discharges to the masts are quite high and much effort has gone into minimizing the damage caused by lightning activity. A major part of the thesis deals with data analysis and modelling. There are detailed discussions on the various types of wind sensors and their calibration, the data acquisition system and operating experiences with it, the database, data quality control, the wind speed profile and turbulence. 40 refs., 78 figs., 17 tabs.

Source apportionment and location by selective wind sampling and Positive Matrix Factorization.

Science.gov (United States)

Venturini, Elisa; Vassura, Ivano; Raffo, Simona; Ferroni, Laura; Bernardi, Elena; Passarini, Fabrizio

2014-10-01

In order to determine the pollution sources in a suburban area and identify the main direction of their origin, PM2.5 was collected with samplers coupled with a wind select sensor and then subjected to Positive Matrix Factorization (PMF) analysis. In each sample, soluble ions, organic carbon, elemental carbon, levoglucosan, metals, and Polycyclic Aromatic Hydrocarbons (PAHs) were determined. PMF results identified six main sources affecting the area: natural gas home appliances, motor vehicles, regional transport, biomass combustion, manufacturing activities, and secondary aerosol. The connection of factor temporal trends with other parameters (i.e., temperature, PM2.5 concentration, and photochemical processes) confirms factor attributions. PMF analysis indicated that the main source of PM2.5 in the area is secondary aerosol. This should be mainly due to regional contributions, owing to both the secondary nature of the source itself and the higher concentration registered in inland air masses. The motor vehicle emission source contribution is also important. This source likely has a prevalent local origin. The most toxic determined components, i.e., PAHs, Cd, Pb, and Ni, are mainly due to vehicular traffic. Even if this is not the main source in the study area, it is the one of greatest concern. The application of PMF analysis to PM2.5 collected with this new sampling technique made it possible to obtain more detailed results on the sources affecting the area compared to a classical PMF analysis.

75 FR 23263 - Alta Wind I, LLC; Alta Wind II, LLC; Alta Wind III, LLC; Alta Wind IV, LLC; Alta Wind V, LLC...

Science.gov (United States)

2010-05-03

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. EL10-62-000] Alta Wind I, LLC; Alta Wind II, LLC; Alta Wind III, LLC; Alta Wind IV, LLC; Alta Wind V, LLC; Alta Wind VI, LLC; Alta Wind VII, LLC; Alta Wind VIII, LLC; Alta Windpower Development, LLC; TGP Development Company, LLC...

77 FR 29633 - Alta Wind VII, LLC, Alta Wind IX, LLC, Alta Wind X, LLC, Alta Wind XI, LLC, Alta Wind XII, LLC...

Science.gov (United States)

2012-05-18

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. EL12-68-000] Alta Wind VII, LLC, Alta Wind IX, LLC, Alta Wind X, LLC, Alta Wind XI, LLC, Alta Wind XII, LLC, Alta Wind XIII, LLC, Alta Wind XIV, LLC, Alta Wind XV, LLC, Alta Windpower Development, LLC, TGP Development Company, LLC...

Aplicação da via curta para remoção biológica de nitrogênio de lixiviado de aterro sanitário utilizando reator em batelada sequencial

Directory of Open Access Journals (Sweden)

Luiz Felipe Tavares De Santana

2015-12-01

Full Text Available A presente pesquisa teve o objetivo de estudar a remoção biológica de nitrogênio amoniacal (N-NH3 e matéria orgânica biodegradável presente em lixiviado de aterro sanitário, aplicando a nitrificação por meio da via curta, operando um reator de polietileno, em bateladas sequenciais, com volumes úteis superiores a 400 L, ou seja, em escala piloto, aerado por meio de compressor de 1 cv. O experimento foi realizado no aterro sanitário em operação há onze anos, localizado no município de Camaçari - Bahia e operado pela empresa LIMPEC, responsável pelos serviços de coleta, transporte e destinação final dos resíduos sólidos urbanos e industriais não perigosos, gerados nos municípios de Camaçari e Dias D’Ávila, Bahia. O experimento foi conduzido durante 165 dias. Foram realizados: 7 (sete ciclos de tratamento utilizando razões de troca volumétrica de 10% e aerando o conteúdo do reator por 18 horas; 5 (cinco ciclos com razão de troca volumétrica de 20% e aerando o conteúdo do reator por 18 horas e, finalmente, 7 (sete ciclos com razão de troca volumétrica igual a 20% e aerando o conteúdo do reator por 24 horas. Todos os ciclos de tratamento foram operados com o conteúdo do reator a temperatura ambiente, sem correção de pH, e a concentração de oxigênio dissolvido (OD, durante a aeração, foi sempre inferior a 1,0 mg O2/L. Os melhores resultados de eficiência de remoção de poluentes de interesse foram obtidos quando o sistema foi operado com RTV iguais a 10 e 20% e tempos de aeração iguais a 18 e 24 horas respectivamente. Nessas condições operacionais, a remoção de N-NH3 variou entre 56 e 100%, correspondendo a concentrações efluentes entre 0,0 e 84,0 mg N-NH3/L, ou seja, durante 11 ciclos de tratamento o efluente atendeu à Resolução CONAMA 430/2011. O alcance do acúmulo de nitrito, avaliado por meio da razão nitrito/nitrogênio oxidado, mostrou-se estável durante todo o experimento. Ao longo

Wind-power turns up the heat - Minergie, heat pumps and wind; Windstrom heizt ein

Energy Technology Data Exchange (ETDEWEB)

Gutknecht, B.

2003-07-01

This short article discusses the advantages of using wind energy to provide lighting as well as power for the heat pumps often used in houses built to the Swiss Minergie low-energy consumption standard. The extra costs caused by purchase of wind-generated electrical energy instead of 'normal' electricity are, according to the author, low in comparison with other costs incurred by the inhabitants for such things as, for example, pocket money, internet connections and other amenities. A sample calculation for an average Minergie house is presented. The article is rounded off by a collection of facts on wind energy in general and its use in Switzerland in particular.

Taylor Law in Wind Energy Data

Directory of Open Access Journals (Sweden)

Rudy Calif

2015-10-01

Full Text Available The Taylor power law (or temporal fluctuation scaling, is a scaling relationship of the form σ ~  (Pλ where !! is the standard deviation and hPi the mean value of a sample of a time series has been observed for power output data sampled at 5 min and 1 s and from five wind farms and a single wind turbine, located at different places. Furthermore, an analogy with the turbulence field is performed, consequently allowing the establishment of a scaling relationship between the turbulent production IP and the mean value (P.

Soil deflation analyses from wind erosion events

Directory of Open Access Journals (Sweden)

Lenka Lackóová

2015-09-01

Full Text Available There are various methods to assess soil erodibility for wind erosion. This paper focuses on aggregate analysis by a laser particle sizer ANALYSETTE 22 (FRITSCH GmbH, made to determine the size distribution of soil particles detached by wind (deflated particles. Ten soil samples, trapped along the same length of the erosion surface (150–155 m but at different wind speeds, were analysed. The soil was sampled from a flat, smooth area without vegetation cover or soil crust, not affected by the impact of windbreaks or other barriers, from a depth of maximum 2.5 cm. Prior to analysis the samples were prepared according to the relevant specifications. An experiment was also conducted using a device that enables characterisation of the vertical movement of the deflated material. The trapped samples showed no differences in particle size and the proportions of size fractions at different hourly average wind speeds. It was observed that most of particles travelling in saltation mode (size 50–500 μm – 58–70% – moved vertically up to 26 cm above the soil surface. At greater heights, particles moving in suspension mode (floating in the air; size < 100 μm accounted for up to 90% of the samples. This result suggests that the boundary between the two modes of the vertical movement of deflated soil particles lies at about 25 cm above the soil surface.

O uso do carvão ativado produzido a partir da casca da Moringa oleifera, como adsorvente na remoção de metais pesados presentes na água.

OpenAIRE

Nogueira, Marcopaulo Wanderley

2010-01-01

A necessidade de atender os padrões de qualidade da água de acordo com a legislação ambiental tanto para o consumo humano quanto para o lançamento de efluentes levam a busca de soluções de baixo custo e eficientes para que seja viável o avanço do saneamento ambiental. O carvão ativado produzido a partir das cascas da semente da Moringa oleifera tem sido estudado e apontado como solução alternativa para remoção de poluentes em regiões tropicais onde a p...

Aggregated wind power generation probabilistic forecasting based on particle filter

International Nuclear Information System (INIS)

Li, Pai; Guan, Xiaohong; Wu, Jiang

2015-01-01

Highlights: • A new method for probabilistic forecasting of aggregated wind power generation. • A dynamic system is established based on a numerical weather prediction model. • The new method handles the non-Gaussian and time-varying wind power uncertainties. • Particle filter is applied to forecast predictive densities of wind generation. - Abstract: Probability distribution of aggregated wind power generation in a region is one of important issues for power system daily operation. This paper presents a novel method to forecast the predictive densities of the aggregated wind power generation from several geographically distributed wind farms, considering the non-Gaussian and non-stationary characteristics in wind power uncertainties. Based on a mesoscale numerical weather prediction model, a dynamic system is established to formulate the relationship between the atmospheric and near-surface wind fields of geographically distributed wind farms. A recursively backtracking framework based on the particle filter is applied to estimate the atmospheric state with the near-surface wind power generation measurements, and to forecast the possible samples of the aggregated wind power generation. The predictive densities of the aggregated wind power generation are then estimated based on these predicted samples by a kernel density estimator. In case studies, the new method presented is tested on a 9 wind farms system in Midwestern United States. The testing results that the new method can provide competitive interval forecasts for the aggregated wind power generation with conventional statistical based models, which validates the effectiveness of the new method

Eficiência do reator seqüencial em batelada (RSB na remoção de nitrogênio no tratamento de esgoto doméstico com DQO baixa The sequencing batch reactor (SBR efficiency in the removal of nitrogen on the treatment of domestic sewage with low COD

Directory of Open Access Journals (Sweden)

Luiz Fernando de Abreu Cybis

2004-09-01

Full Text Available Este trabalho tem como objetivo avaliar a eficiência e a estabilidade do RSB na remoção de nitrogênio no tratamento de esgoto doméstico com DQO baixa. O reator utilizado no experimento possui volume de trabalho de 600 L e trata 1200 L/d de esgoto bruto em três bateladas de oito horas. A partir dos dados obtidos na pesquisa, observou-se que o reator seqüencial em batelada possibilitou a remoção média de nitrogênio total igual a 88 % no tratamento de esgoto doméstico com DQO média de 257 mg/L. A remoção de DQO foi de 90 %, a média da alcalinidade total no efluente foi 72 mgCaCO3/L e o índice volumétrico de lodo médio ficou em 86 mL/g. Estes resultados indicam que é possível utilizar RSB para o tratamento de esgoto doméstico com matéria orgânica reduzida sem comprometer a qualidade do efluente, a remoção de nitrogênio e a estabilidade operacional do sistema.This work had the objective of evaluating the SBR efficiency and stability in the removal of nitrogen on the treatment of domestic sewage with low COD. The reactor used in the experiment has a working volume of 600 L, and treats 1200 L/d of raw sewage in three 8-hour cycles. From the data gathered during the research, it was realized that the SBR fostered an average removal of total nitrogen equal to 88% in the treatment of a domestic sewage with an average COD of 257 mg/L. The COD removal was 90%, the final effluent total alkalinity was 72 mgCaCO3/L, and the sludge volumetric index was 86 mL/g. The results indicate that is possible to use SBR for the treatment of domestic sewage with low organic matter without compromising the final effluent quality, the nitrogen removal ability, and the stability of the system.

On the energy pattern factor in wind measurements

Energy Technology Data Exchange (ETDEWEB)

Buick, T R; Doherty, M A; McMullan, J.T., Morgan, R.; Murray, R B

1977-01-01

Measurements of energy pattern factor K/sub e/ were made using a continuous-analogue wind-power metering technique, rather than by the more usual sampling procedure. The values obtained were significantly larger than the usually accepted figure. The discrepancy is attributed partly to the method of measurement, which includes the actual power present rather than the amount that can be extracted, and partly to the use of rather more typical wind speeds. It is concluded, however, that more energy can be derived from wind schemes than was thought, even during periods of light wind. These conclusions improve the viability of wind power plants.

Simulation for Grid Connected Wind Turbines with Fluctuating

Science.gov (United States)

Ye, Ying; Fu, Yang; Wei, Shurong

This paper establishes the whole dynamic model of wind turbine generator system which contains the wind speed model and DFIG wind turbines model .A simulation sample based on the mathematical models is built by using MATLAB in this paper. Research are did on the performance characteristics of doubly-fed wind generators (DFIG) which connected to power grid with three-phase ground fault and the disturbance by gust and mixed wind. The capacity of the wind farm is 9MW which consists of doubly-fed wind generators (DFIG). Simulation results demonstrate that the three-phase ground fault occurs on grid side runs less affected on the stability of doubly-fed wind generators. However, as a power source, fluctuations of the wind speed will run a large impact on stability of double-fed wind generators. The results also show that if the two disturbances occur in the meantime, the situation will be very serious.

Equivalent models of wind farms by using aggregated wind turbines and equivalent winds

International Nuclear Information System (INIS)

Fernandez, L.M.; Garcia, C.A.; Saenz, J.R.; Jurado, F.

2009-01-01

As a result of the increasing wind farms penetration on power systems, the wind farms begin to influence power system, and therefore the modeling of wind farms has become an interesting research topic. In this paper, new equivalent models of wind farms equipped with wind turbines based on squirrel-cage induction generators and doubly-fed induction generators are proposed to represent the collective behavior on large power systems simulations, instead of using a complete model of wind farms where all the wind turbines are modeled. The models proposed here are based on aggregating wind turbines into an equivalent wind turbine which receives an equivalent wind of the ones incident on the aggregated wind turbines. The equivalent wind turbine presents re-scaled power capacity and the same complete model as the individual wind turbines, which supposes the main feature of the present equivalent models. Two equivalent winds are evaluated in this work: (1) the average wind from the ones incident on the aggregated wind turbines with similar winds, and (2) an equivalent incoming wind derived from the power curve and the wind incident on each wind turbine. The effectiveness of the equivalent models to represent the collective response of the wind farm at the point of common coupling to grid is demonstrated by comparison with the wind farm response obtained from the detailed model during power system dynamic simulations, such as wind fluctuations and a grid disturbance. The present models can be used for grid integration studies of large power system with an important reduction of the model order and the computation time

78 FR 29364 - Exelon Corporation, Exelon Wind 1, LLC, Exelon Wind 2, LLC, Exelon Wind 3, LLC, Exelon Wind 4...

Science.gov (United States)

2013-05-20

...-005, QF07-55-005, QF07-56-005, QF07-257-004] Exelon Corporation, Exelon Wind 1, LLC, Exelon Wind 2, LLC, Exelon Wind 3, LLC, Exelon Wind 4, LLC, Exelon Wind 5, LLC, Exelon Wind 6, LLC, Exelon Wind 7, LLC, Exelon Wind 8, LLC, Exelon Wind 9, LLC, Exelon Wind 10, LLC, Exelon Wind 11, LLC, High Plains...

Unit commitment with wind power generation: integrating wind forecast uncertainty and stochastic programming.

Energy Technology Data Exchange (ETDEWEB)

Constantinescu, E. M.; Zavala, V. M.; Rocklin, M.; Lee, S.; Anitescu, M. (Mathematics and Computer Science); (Univ. of Chicago); (New York Univ.)

2009-10-09

We present a computational framework for integrating the state-of-the-art Weather Research and Forecasting (WRF) model in stochastic unit commitment/energy dispatch formulations that account for wind power uncertainty. We first enhance the WRF model with adjoint sensitivity analysis capabilities and a sampling technique implemented in a distributed-memory parallel computing architecture. We use these capabilities through an ensemble approach to model the uncertainty of the forecast errors. The wind power realizations are exploited through a closed-loop stochastic unit commitment/energy dispatch formulation. We discuss computational issues arising in the implementation of the framework. In addition, we validate the framework using real wind speed data obtained from a set of meteorological stations. We also build a simulated power system to demonstrate the developments.

Effectiveness of EDTA and EDTA-T brushingm on the removal of root surface smear layer Efeito do EDTA e EDTA-T aplicado de forma ativa na remoção de "smear layer" de superfícies radiculares

Directory of Open Access Journals (Sweden)

José Eduardo Cezar Sampaio

2003-12-01

Full Text Available The purpose of this study was to compare the removal of root surface smear layer following active application of EDTA gel and EDTA-T (texapon gel in different concentrations (5%, 10%, 15%, 20% and 24%, using scanning electron microscopy. A total of 220 dentin blocks obtained from the root surfaces of extracted teeth were divided into 3 groups: Group I - (control application of saline solution (n = 20; Group II - EDTA gel (pH 7.0 was applied in the following concentrations: 5%, 10%, 15%, 20% and 24% (n = 100; Group III - EDTA-T gel (pH 7.0 applied in the same concentrations described above (n = 100. The photomicrographs were evaluated by one calibrated examiner using a smear layer removal index and following statistical analysis (Kruskal-Wallis test. The results demonstrated that the specimens treated with EDTA and EDTA-T gel presented a better smear layer removal than the control group (p 0.05. Within the limits of this study, it can be concluded that all treatment modalities effectively removed the smear layer from the root surface. The addition of texapon into the EDTA gel formulation did not increase its effectiveness.O objetivo do presente estudo foi comparar, através de microscopia eletrônica de varredura, o efeito da aplicação de gel de EDTA e de EDTA-T (texapon em diferentes concentrações (5%, 10%, 15%, 20% e 24% na remoção de "smear layer" de superfícies radiculares previamente raspadas com instrumentos manuais. Duzentos e vinte espécimes de superfícies radiculares submetidas à raspagem foram divididos em 3 grupos. Grupo I - (controle solução salina (n = 20; Grupo II - gel de EDTA (pH 7,0 nas concentrações de 5%, 10%, 15%, 20% e 24% (n = 100; Grupo III - gel de EDTA-T (pH 7,0 nas concentrações acima descritas (n = 100. As fotomicrografias obtidas foram avaliadas por um examinador calibrado através da aplicação de um índice de remoção de "smear layer", e os dados foram analisados através de análise estat

SAT-WIND project. Final report[Winds from satellites for offshore and coastal wind energy mapping and wind-indexing

Energy Technology Data Exchange (ETDEWEB)

Hasager, C.B.; Astrup, P.; Nielsen, M. (and others)

2007-04-15

The SAT-WIND project 'Winds from satellites for offshore and coastal wind energy mapping and wind-indexing' was a research project funded by STVF/DSF in the years 2003 to 2006 (Sagsnr. 2058-03-0006). The goal of the project was to verify the applicability of satellite wind maps derived from passive microwave, altimeter, scatterometer and imaging Synthetic Aperture Radar (SAR) technologies for wind energy tools for wind resources and wind-indexing. The study area was the Danish Seas including the North Sea, interior seas and the Baltic Sea. The report describes technical details on the satellite data sources including: 1) passive microwave (SSM/I, AMSR-E), 2) passive microwave polarimetric (WindSat), 3) scatterometer (ERS, QuikSCAT, Midori-2 and NSCAT), 4) altimeter (ERS, Topex, Poseidon, GFO-1, Jason-1), 5) SAR (ERS, Envisat). The SAR wind maps were treated in S-WAsP developed by Risoe National Laboratory in cooperation with GRAS A/S in the innovative project SAT-WIND-SMV (Sagsnr. 2104-05-0084) in the years 2005 and 2006 in parallel with SAT-WIND. The results from the SAT-WIND project are presented. These include ocean wind statistics, offshore wind resource estimates and comparison results for wind-indexing. (au)

SAT-WIND project. Final report[Winds from satellites for offshore and coastal wind energy mapping and wind-indexing

Energy Technology Data Exchange (ETDEWEB)

Hasager, C B; Astrup, P; Nielsen, M [and others

2007-04-15

The SAT-WIND project 'Winds from satellites for offshore and coastal wind energy mapping and wind-indexing' was a research project funded by STVF/DSF in the years 2003 to 2006 (Sagsnr. 2058-03-0006). The goal of the project was to verify the applicability of satellite wind maps derived from passive microwave, altimeter, scatterometer and imaging Synthetic Aperture Radar (SAR) technologies for wind energy tools for wind resources and wind-indexing. The study area was the Danish Seas including the North Sea, interior seas and the Baltic Sea. The report describes technical details on the satellite data sources including: 1) passive microwave (SSM/I, AMSR-E), 2) passive microwave polarimetric (WindSat), 3) scatterometer (ERS, QuikSCAT, Midori-2 and NSCAT), 4) altimeter (ERS, Topex, Poseidon, GFO-1, Jason-1), 5) SAR (ERS, Envisat). The SAR wind maps were treated in S-WAsP developed by Risoe National Laboratory in cooperation with GRAS A/S in the innovative project SAT-WIND-SMV (Sagsnr. 2104-05-0084) in the years 2005 and 2006 in parallel with SAT-WIND. The results from the SAT-WIND project are presented. These include ocean wind statistics, offshore wind resource estimates and comparison results for wind-indexing. (au)

Modelling Wind for Wind Farm Layout Optimization Using Joint Distribution of Wind Speed and Wind Direction

OpenAIRE

Ju Feng; Wen Zhong Shen

2015-01-01

Reliable wind modelling is of crucial importance for wind farm development. The common practice of using sector-wise Weibull distributions has been found inappropriate for wind farm layout optimization. In this study, we propose a simple and easily implementable method to construct joint distributions of wind speed and wind direction, which is based on the parameters of sector-wise Weibull distributions and interpolations between direction sectors. It is applied to the wind measurement data a...

Desempenho de métodos baseados em indução de fluorescência na avaliação da remoção de dentina cariada

Directory of Open Access Journals (Sweden)

Thalita BOLDIERI

Full Text Available Resumo Introdução Critérios clínicos vêm sendo utilizados para determinação da presença de tecido cariado remanescente, mas geram dúvidas, tornando-se relevante a utilização de métodos que auxiliem na determinação da presença de cárie dentária remanescente. Objetivo Avaliar in vitro a eficácia de métodos de indução de fluorescência no diagnóstico da remoção de tecido cariado artificial dentinário. Material e método O esmalte oclusal de 94 terceiros molares humanos hígidos foi removido, expondo a dentina subjacente, para indução microbiológica de lesão de cárie artificial. Após a remoção do tecido cariado induzido, o remanescente dentinário foi avaliado por dois examinadores com DIAGNOdent, DIAGNOdent pen e Quantitative Light-Induced Fluorescence (QLF. Após todas as avaliações, secções dos dentes foram observadas e fotografadas em lupa estereoscópica com 30× de aumento por um examinador independente. As imagens foram analisadas no software Image J, permitindo a quantificação de tecido remanescente em milímetros quadrados. Foi calculada a reprodutibilidade interexaminador através de coeficiente intraclasse, sensibilidade, especificidade e área sob a curva ROC, e o teste de McNemar (p0,05. Os valores de reprodutibilidade variaram entre 0,952 e 0,978. Conclusão Dentre os métodos utilizados, o DIAGNOdent e o DIAGNOdent pen apresentaram melhor desempenho na avaliação da presença de cárie artificial remanescente quando comparados ao QLF.

Annoyance, detection and recognition of wind turbine noise.

Science.gov (United States)

Van Renterghem, Timothy; Bockstael, Annelies; De Weirt, Valentine; Botteldooren, Dick

2013-07-01

Annoyance, recognition and detection of noise from a single wind turbine were studied by means of a two-stage listening experiment with 50 participants with normal hearing abilities. In-situ recordings made at close distance from a 1.8-MW wind turbine operating at 22 rpm were mixed with road traffic noise, and processed to simulate indoor sound pressure levels at LAeq 40 dBA. In a first part, where people were unaware of the true purpose of the experiment, samples were played during a quiet leisure activity. Under these conditions, pure wind turbine noise gave very similar annoyance ratings as unmixed highway noise at the same equivalent level, while annoyance by local road traffic noise was significantly higher. In a second experiment, listeners were asked to identify the sample containing wind turbine noise in a paired comparison test. The detection limit of wind turbine noise in presence of highway noise was estimated to be as low as a signal-to-noise ratio of -23 dBA. When mixed with local road traffic, such a detection limit could not be determined. These findings support that noticing the sound could be an important aspect of wind turbine noise annoyance at the low equivalent levels typically observed indoors in practice. Participants that easily recognized wind-turbine(-like) sounds could detect wind turbine noise better when submersed in road traffic noise. Recognition of wind turbine sounds is also linked to higher annoyance. Awareness of the source is therefore a relevant aspect of wind turbine noise perception which is consistent with previous research. Copyright © 2013 Elsevier B.V. All rights reserved.

Cup anemometer response to the wind turbulence-measurement of the horizontal wind variance

Directory of Open Access Journals (Sweden)

S. Yahaya

2004-11-01

Full Text Available This paper presents some dynamic characteristics of an opto-electronic cup anemometer model in relation to its response to the wind turbulence. It is based on experimental data of the natural wind turbulence measured both by an ultrasonic anemometer and two samples of the mentioned cup anemometer. The distance constants of the latter devices measured in a wind tunnel are in good agreement with those determined by the spectral analysis method proposed in this study. In addition, the study shows that the linear compensation of the cup anemometer response, beyond the cutoff frequency, is limited to a given frequency, characteristic of the device. Beyond this frequency, the compensation effectiveness relies mainly on the wind characteristics, particularly the direction variability and the horizontal turbulence intensity. Finally, this study demonstrates the potential of fast cup anemometers to measure some turbulence parameters (like wind variance with errors of the magnitude as those deriving from the mean speed measurements. This result proves that fast cup anemometers can be used to assess some turbulence parameters, especially for long-term measurements in severe climate conditions (icing, snowing or sandy storm weathers.

Wind tunnel evaluation of Hi-Vol TSP effectiveness data

Data.gov (United States)

U.S. Environmental Protection Agency — Wind tunnel evaluation of EPA's Hi-Vol TSP sampler for sampling effectiveness with regards to aerodynamic particle diameter (5 to 35 microns), wind speed (2, 8, 24...

Plaque removal by manual and electric toothbrushing among children Remoção de placa bacteriana pela escovação elétrica e manual em crianças

Directory of Open Access Journals (Sweden)

Carolina Covolo da COSTA

2001-12-01

Full Text Available The purpose of this study was to compare the effectiveness of plaque control performed with electric and manual toothbrushes. Fifteen children with primary dentition and 14 children with mixed dentition were divided in two groups and randomly assigned to utilize a manual or an electric toothbrush. In the first session, professional plaque removal was performed, and the children spent 24 hours without brushing their teeth. In the second session, plaque was disclosed and assessed on all facial and lingual surfaces. After that, all children brushed their teeth with the predetermined toothbrush. The next procedure was the disclosure and measurement of residual plaque. After a period of 7 days, the children switched the kind of toothbrush, and the same procedures were repeated. According to the statistical analysis of the results, there were no significant differences concerning plaque removal when the toothbrushes were utilized by children with mixed dentition. On the other hand, the electric toothbrush promoted significantly greater plaque removal on the lingual surfaces of teeth from children with primary dentition.A proposta deste estudo foi comparar a eficácia da remoção de placa bacteriana pelas escovações elétrica e manual. Quinze crianças portadoras de dentadura decídua e 14 crianças portadoras de dentadura mista foram divididas em dois grupos e, aleatoriamente, designadas a utilizar a escova manual ou a escova elétrica. Na primeira sessão, foi realizada completa remoção de placa bacteriana e após, as crianças permaneceram 24 horas sem escovar os dentes. Na segunda sessão, foi feita revelação de placa bacteriana e computação de seu índice para todas as faces vestibulares e linguais dos dentes. Depois, todos os participantes escovaram os dentes com a escova predeterminada. A próxima etapa foi a revelação e medição da placa residual. Decorridos 7 dias, as crianças trocaram para a outra escova dental e os mesmos

Wind turbines, is it just wind?

International Nuclear Information System (INIS)

Boiteux, M.

2012-01-01

The author first outlines that wind energy is not only random, but almost absent in extreme situations when it would be needed (for example and notably, very cold weather without wind). He suggests the association of a gas turbine to each wind turbine, so that the gas turbine will replace non operating wind turbines. He notices that wind turbines are not proximity energy as they were said to be, and that profitability in fact requires tens of grouped giant wind turbines. He also outlines the high cost of construction of grids for the connection of these wind turbines. Thus, he states that wind energy is far from being profitable in the present conditions of electricity tariffs in France

Wind: new wind markets

International Nuclear Information System (INIS)

Cameron, A.

2005-01-01

The June 2005 edition of 'Wind Force 12' suggests that wind could generate 12% of global electricity requirements by 2020. But what moves a potential market into an emerging one? Geographical factors include a good wind resource, plenty of open space and the ability to get the generated electricity to end-users. A country's political framework is equally important, with fixed price systems, renewable quota systems and political will all playing a part. Some potential wind markets around the world are thought to have the conditions necessary to become key players in the wind industry. The emerging markets in countries such as Australia, Brazil, Canada, France, Japan and the Philippines are highlighted as examples

ANALYSIS OF MONTE CARLO SIMULATION SAMPLING TECHNIQUES ON SMALL SIGNAL STABILITY OF WIND GENERATOR- CONNECTED POWER SYSTEM

Directory of Open Access Journals (Sweden)

TEMITOPE RAPHAEL AYODELE

2016-04-01

Full Text Available Monte Carlo simulation using Simple Random Sampling (SRS technique is popularly known for its ability to handle complex uncertainty problems. However, to produce a reasonable result, it requires huge sample size. This makes it to be computationally expensive, time consuming and unfit for online power system applications. In this article, the performance of Latin Hypercube Sampling (LHS technique is explored and compared with SRS in term of accuracy, robustness and speed for small signal stability application in a wind generator-connected power system. The analysis is performed using probabilistic techniques via eigenvalue analysis on two standard networks (Single Machine Infinite Bus and IEEE 16–machine 68 bus test system. The accuracy of the two sampling techniques is determined by comparing their different sample sizes with the IDEAL (conventional. The robustness is determined based on a significant variance reduction when the experiment is repeated 100 times with different sample sizes using the two sampling techniques in turn. Some of the results show that sample sizes generated from LHS for small signal stability application produces the same result as that of the IDEAL values starting from 100 sample size. This shows that about 100 sample size of random variable generated using LHS method is good enough to produce reasonable results for practical purpose in small signal stability application. It is also revealed that LHS has the least variance when the experiment is repeated 100 times compared to SRS techniques. This signifies the robustness of LHS over that of SRS techniques. 100 sample size of LHS produces the same result as that of the conventional method consisting of 50000 sample size. The reduced sample size required by LHS gives it computational speed advantage (about six times over the conventional method.

Wind energy applications of synthetic aperture radar

Energy Technology Data Exchange (ETDEWEB)

Bruun Christiansen, M.

2006-11-15

Synthetic aperture radars (SAR), mounted on satellites or aircraft, have proven useful for ocean wind mapping. Wind speeds at the height 10 m may be retrieved from measurements of radar backscatter using empirical model functions. The resulting wind fields are valuable in offshore wind energy planning as a supplement to on site measurements, which are costly and sparse, and model wind fields, which are not fully validated. Two applications of SAR measurements in offshore wind energy planning are addressed here: the study of wind farm wake effects and the potential of using SAR winds in offshore wind resource assessment. Firstly, wind wakes behind two large offshore wind farms in Denmark Horns Rev and Nysted are identified. A region of reduced wind speed is found downstream of both wind farms from the SAR wind fields. The wake extent and magnitude depends on the wind speed, the atmospheric stability, and the fraction of turbines operating. Wind farm wake effects are detected up to 20 km downwind of the last turbine. This distance is longer than predicted by state-of-the art wake models. Wake losses are typically 10-20% near the wind farms. Secondly, the potential of using SAR wind maps in offshore wind resource assessment is investigated. The resource assessment is made through Weibull fitting to frequency observations of wind speed and requires at least 100 satellite observations per year for a given site of interest. Predictions of the energy density are very sensitive to the wind speed and the highest possible accuracy on SAR wind retrievals is therefore sought. A 1.1 m s{sup -1} deviation on the mean wind speed is found through comparison with mast measurements at Horns Rev. The accuracy on mean wind speeds and energy densities found from satellite measurements varies with different empirical model functions. Additional uncertainties are introduced by the infrequent satellite sampling at fixed times of the day. The accuracy on satellite based wind resource

Remoção de sulfeto em uma estação de tratamento de efluentes de níquel por oxidação úmida

OpenAIRE

ALVES, Valderice Pereira

2006-01-01

O tratamento das águas residuárias de uma indústria de componentes eletrônicos que utiliza níquel em seu processo de deposição eletroquímica, consiste no uso dos métodos físico-químicos tradicionais, como precipitação química e filtração. Esta indústria da região nordeste remove o níquel presente em seu efluente pela adição de sulfeto de sódio em excesso garantindo a completa precipitação do metal. O processo de oxidação adotado pela indústria para remover o sulfeto remanescente é a remoção c...

Toward Robust and Efficient Climate Downscaling for Wind Energy

Science.gov (United States)

Vanvyve, E.; Rife, D.; Pinto, J. O.; Monaghan, A. J.; Davis, C. A.

2011-12-01

This presentation describes a more accurate and economical (less time, money and effort) wind resource assessment technique for the renewable energy industry, that incorporates innovative statistical techniques and new global mesoscale reanalyzes. The technique judiciously selects a collection of "case days" that accurately represent the full range of wind conditions observed at a given site over a 10-year period, in order to estimate the long-term energy yield. We will demonstrate that this new technique provides a very accurate and statistically reliable estimate of the 10-year record of the wind resource by intelligently choosing a sample of ±120 case days. This means that the expense of downscaling to quantify the wind resource at a prospective wind farm can be cut by two thirds from the current industry practice of downscaling a randomly chosen 365-day sample to represent winds over a "typical" year. This new estimate of the long-term energy yield at a prospective wind farm also has far less statistical uncertainty than the current industry standard approach. This key finding has the potential to reduce significantly market barriers to both onshore and offshore wind farm development, since insurers and financiers charge prohibitive premiums on investments that are deemed to be high risk. Lower uncertainty directly translates to lower perceived risk, and therefore far more attractive financing terms could be offered to wind farm developers who employ this new technique.

Grid Integration of Offshore Wind | Wind | NREL

Science.gov (United States)

Grid Integration of Offshore Wind Grid Integration of Offshore Wind Much can be learned from the existing land-based integration research for handling the variability and uncertainty of the wind resource Arklow Bank offshore wind park consists of seven GE Wind 3.6-MW wind turbines. Integration and

Characteristics for wind energy and wind turbines by considering vertical wind shear

Institute of Scientific and Technical Information of China (English)

郑玉巧; 赵荣珍

2015-01-01

The probability distributions of wind speeds and the availability of wind turbines were investigated by considering the vertical wind shear. Based on the wind speed data at the standard height observed at a wind farm, the power-law process was used to simulate the wind speeds at a hub height of 60 m. The Weibull and Rayleigh distributions were chosen to express the wind speeds at two different heights. The parameters in the model were estimated via the least square (LS) method and the maximum likelihood estimation (MLE) method, respectively. An adjusted MLE approach was also presented for parameter estimation. The main indices of wind energy characteristics were calculated based on observational wind speed data. A case study based on the data of Hexi area, Gansu Province of China was given. The results show that MLE method generally outperforms LS method for parameter estimation, and Weibull distribution is more appropriate to describe the wind speed at the hub height.

Remoção de atrazina e metabólitos pela filtração lenta com leito de areia e carvão ativado granular Removal of atrazine and metabolites through slow filtration by sand and granular activated carbon

Directory of Open Access Journals (Sweden)

Edumar Ramos Cabral Coelho

2012-09-01

Full Text Available A atrazina (ATZé um herbicida largamente utilizado no mundo, sendo encontrada associada aos seus produtos de degradação em águas superficiais e subterrâneas. Pertence à classe das s-triazinas e, juntamente com os metabólitos clorados deetilatrazina (DEA e deisopropilatrazina (DIA, possui potencial carcinogênico e toxicidade como disruptores endócrinos. A limitação dos processos que empregam a coagulação química na remoção de ATZ, a conhecida capacidade do carvão ativado em remover microcontaminantes em água e o risco que a ATZ e seus metabólitos apresentam à saúde motivaram o estudo da filtração lenta com leito de areia e carvão ativado granular. Os resultados apontaram a eficiência do processo de filtração lenta com camada intermediária de carvão ativado granular na remoção de ATZ e a limitação deste na remoção dos metabólitos DEA, DIA e deetilhidroxiatrazina (DEHA.Atrazine (ATZ is widely used as herbicide, commonly found in association to its degradation products in surface water and groundwater. It belongs to the class of s-triazines and together with the chlorinated metabolites dieethylatrazine (DEA and deisopropilatrazine (DIA have carcinogenic potential and toxicity as endocrine disruptors. The limitation of the processes employing chemical coagulation in the removal of atrazine, the known ability of activated carbon to remove microcontaminants in water and the risk that atrazine and the potential toxicity to human health of its metabolits motivated the study of slow sand filtration bed combined with granular activated carbon. The results showed the high efficiency of the slow filtration process with intermediate layer of granular activated carbon in the removal of atrazine and its limitation on the removal of the metabolites DEA, DIA and diethylhidroxiatrazine (DEHA.

Upper wind observing systems used for meteorological operations

Directory of Open Access Journals (Sweden)

J. Nash

Full Text Available Methods of upper wind measurements used in operational meteorology have been reviewed to provide guidance to those developing wind profiler radar systems. The main limitations of the various methods of tracking weather balloons are identified using results from the WMO radiosonde comparisons and additional tests in the United Kingdom. Costs associated with operational balloon measurements are reviewed. The sampling and quality of operational aircraft wind observations are illustrated with examples from the ASDAR system. Measurement errors in horizontal winds are quantified wherever possible. When tracking equipment is functioning correctly, random errors in southerly and westerly wind component measurements from aircraft and weather balloons are usually in the range 0.5-2 m s^-1.

WIND observations of coherent electrostatic waves in the solar wind

Directory of Open Access Journals (Sweden)

A. Mangeney

1999-03-01

Full Text Available The time domain sampler (TDS experiment on WIND measures electric and magnetic wave forms with a sampling rate which reaches 120 000 points per second. We analyse here observations made in the solar wind near the Lagrange point L1. In the range of frequencies above the proton plasma frequency fpi and smaller than or of the order of the electron plasma frequency fpe, TDS observed three kinds of electrostatic (e.s. waves: coherent wave packets of Langmuir waves with frequencies f ~ fpe, coherent wave packets with frequencies in the ion acoustic range fpi < f < fpe, and more or less isolated non-sinusoidal spikes lasting less than 1 ms. We confirm that the observed frequency of the low frequency (LF ion acoustic wave packets is dominated by the Doppler effect: the wavelengths are short, 10 to 50 electron Debye lengths λD. The electric field in the isolated electrostatic structures (IES and in the LF wave packets is more or less aligned with the solar wind magnetic field. Across the IES, which have a spatial width of the order of ~ 25λD, there is a small but finite electric potential drop, implying an average electric field generally directed away from the Sun. The IES wave forms, which have not been previously reported in the solar wind, are similar, although with a smaller amplitude, to the weak double layers observed in the auroral regions, and to the electrostatic solitary waves observed in other regions in the magnetosphere. We have also studied the solar wind conditions which favour the occurrence of the three kinds of waves: all these e.s. waves are observed more or less continuously in the whole solar wind (except in the densest regions where a parasite prevents the TDS observations. The type (wave packet or IES of the observed LF waves is mainly determined by the proton temperature and by the direction of the magnetic field, which themselves depend on the latitude of WIND with respect to the heliospheric current sheet.Key words

Siemens Wind Power 3.6 MW wind turbines for large offshore wind farms

Energy Technology Data Exchange (ETDEWEB)

Akhmatov, Vladislav; Nygaard Nielsen, Joergen; Thisted, Jan; Groendahl, Erik; Egedal, Per; Noertoft Frydensbjerg, Michael; Jensen, Kim Hoej [Siemens Wind Power A/S, Brande (Denmark)

2008-07-01

Siemens Wind power A/S is the key player on the offshore wind power market. The Siemens Wind Power 3.6 MW variable-speed wind turbine is among the word's largest, most advanced and competitive wind turbines with a solid portfolio of large offshore wind farms. Transmission system operators and developers require dynamic wind turbine models for evaluation of fault-ride-through capability and investigations of power system stability. The even larger size of the on- and offshore wind farms has entailed that the grid impact of the voltage and frequency control capability of the wind farm can be appropriated modelled and evaluated. Siemens Wind Power has developed a dynamic model of the 3.6 MW variable-speed wind turbine with the fault-ride-through sequences and models of the voltage and frequency controllers to be applied for large offshore wind farms. The dynamic models have been implemented in the commercially available simulation tools such as DIgSILENT PowerFactory and Siemens PTI PSS/E and successfully validated from measurements. (orig.)

Microplastics in a wind farm area: A case study at the Rudong Offshore Wind Farm, Yellow Sea, China.

Science.gov (United States)

Wang, Teng; Zou, Xinqing; Li, Baojie; Yao, Yulong; Li, Jiasheng; Hui, Hejiu; Yu, Wenwen; Wang, Chenglong

2018-03-01

Despite the rapid construction of offshore wind farms, the available information regarding the risks of this type of development in terms of emerging pollutants, particularly microplastics, is scarce. In this study, we quantified the level of microplastic pollution at an offshore wind farm in the Yellow Sea, China, in 2016. The abundance of microplastics was 0.330 ± 0.278 items/m 3 in the surface water and 2.58 ± 1.14 items/g (dry) in the sediment. To the best of our knowledge, the level of microplastic pollution in our study area was slightly higher than that in coastal areas around the world. The microplastics detected in the surface waters and sediments were mainly fibrous (75.3% and 68.7%, respectively) and consisted of some granules and films. The microplastics in the samples might originate from garments or ropes via wastewater discharge. The abundance of plastic in the water and sediment samples collected from the wind farm area was lower than that in the samples collected from outside the wind farm area. The anthropogenic hydrodynamic effect was the main factor affecting the local distribution of microplastics. The presence of a wind farm could increase the bed shear stress during ebb tide, disturbing the bed sediment, facilitating its initiation and transport, and ultimately increasing the ease of washing away the microplastics adhered to the sediment. This study will serve as a reference for further studies of the distribution and migration of microplastics in coastal zones subjected to similar marine utilization. Copyright © 2018 Elsevier Ltd. All rights reserved.

Wind conditions for wind turbine design

Energy Technology Data Exchange (ETDEWEB)

Maribo Pedersen, B.

1999-04-01

Delegates from Europe and USA attended the meeting and discussed general aspects of wind conditions for wind turbine design. The subjects and the presented papers covered a very broad range of aspects of wind conditions and related influence on the wind turbine. (EHS)

Doubly Fed Induction Generator Wind Turbines with Fuzzy Controller: A Survey

Directory of Open Access Journals (Sweden)

J. S. Sathiyanarayanan

2014-01-01

Full Text Available Wind energy is one of the extraordinary sources of renewable energy due to its clean character and free availability. With the increasing wind power penetration, the wind farms are directly influencing the power systems. The majority of wind farms are using variable speed wind turbines equipped with doubly fed induction generators (DFIG due to their advantages over other wind turbine generators (WTGs. Therefore, the analysis of wind power dynamics with the DFIG wind turbines has become a very important research issue, especially during transient faults. This paper presents fuzzy logic control of doubly fed induction generator (DFIG wind turbine in a sample power system. Fuzzy logic controller is applied to rotor side converter for active power control and voltage regulation of wind turbine.

Doubly fed induction generator wind turbines with fuzzy controller: a survey.

Science.gov (United States)

Sathiyanarayanan, J S; Kumar, A Senthil

2014-01-01

Wind energy is one of the extraordinary sources of renewable energy due to its clean character and free availability. With the increasing wind power penetration, the wind farms are directly influencing the power systems. The majority of wind farms are using variable speed wind turbines equipped with doubly fed induction generators (DFIG) due to their advantages over other wind turbine generators (WTGs). Therefore, the analysis of wind power dynamics with the DFIG wind turbines has become a very important research issue, especially during transient faults. This paper presents fuzzy logic control of doubly fed induction generator (DFIG) wind turbine in a sample power system. Fuzzy logic controller is applied to rotor side converter for active power control and voltage regulation of wind turbine.

A novel application of artificial neural network for wind speed estimation

Science.gov (United States)

Fang, Da; Wang, Jianzhou

2017-05-01

Providing accurate multi-steps wind speed estimation models has increasing significance, because of the important technical and economic impacts of wind speed on power grid security and environment benefits. In this study, the combined strategies for wind speed forecasting are proposed based on an intelligent data processing system using artificial neural network (ANN). Generalized regression neural network and Elman neural network are employed to form two hybrid models. The approach employs one of ANN to model the samples achieving data denoising and assimilation and apply the other to predict wind speed using the pre-processed samples. The proposed method is demonstrated in terms of the predicting improvements of the hybrid models compared with single ANN and the typical forecasting method. To give sufficient cases for the study, four observation sites with monthly average wind speed of four given years in Western China were used to test the models. Multiple evaluation methods demonstrated that the proposed method provides a promising alternative technique in monthly average wind speed estimation.

IEA Wind Task 26 - Multi-national Case Study of the Financial Cost of Wind Energy; Work Package 1 Final Report

Energy Technology Data Exchange (ETDEWEB)

Schwabe, P.; Lensink, S.; Hand, M.

2011-03-01

The lifetime cost of wind energy is comprised of a number of components including the investment cost, operation and maintenance costs, financing costs, and annual energy production. Accurate representation of these cost streams is critical in estimating a wind plant's cost of energy. Some of these cost streams will vary over the life of a given project. From the outset of project development, investors in wind energy have relatively certain knowledge of the plant's lifetime cost of wind energy. This is because a wind energy project's installed costs and mean wind speed are known early on, and wind generation generally has low variable operation and maintenance costs, zero fuel cost, and no carbon emissions cost. Despite these inherent characteristics, there are wide variations in the cost of wind energy internationally, which is the focus of this report. Using a multinational case-study approach, this work seeks to understand the sources of wind energy cost differences among seven countries under International Energy Agency (IEA) Wind Task 26 - Cost of Wind Energy. The participating countries in this study include Denmark, Germany, the Netherlands, Spain, Sweden, Switzerland, and the United States. Due to data availability, onshore wind energy is the primary focus of this study, though a small sample of reported offshore cost data is also included.

Wind speed errors for LIDARs and SODARs in complex terrain

International Nuclear Information System (INIS)

Bradley, S

2008-01-01

All commercial LIDARs and SODARs are monostatic and hence sample distributed volumes to construct wind vector components. We use an analytic potential flow model to estimate errors arising for a range of LIDAR and SODAR configurations on hills and escarpments. Wind speed errors peak at a height relevant to wind turbines and can be typically 20%

Wind speed errors for LIDARs and SODARs in complex terrain

Energy Technology Data Exchange (ETDEWEB)

Bradley, S [Physics Department, The University of Auckland, Private Bag 92019, Auckland (New Zealand) and School of Computing, Science and Engineering, University of Salford, M5 4WT (United Kingdom)], E-mail: s.bradley@auckland.ac.nz

2008-05-01

All commercial LIDARs and SODARs are monostatic and hence sample distributed volumes to construct wind vector components. We use an analytic potential flow model to estimate errors arising for a range of LIDAR and SODAR configurations on hills and escarpments. Wind speed errors peak at a height relevant to wind turbines and can be typically 20%.

Emission Line Correlations as Diagnostics of Quasar Winds

Science.gov (United States)

Sheldon, Keziah; Richards, Gordon

2018-01-01

We investigate correlations between UV and optical emission line properties for a sample of z~0.5 SDSS (Sloan Digital Sky Survey) quasars that have recently been observed by HST. The sample is designed to be comparable in luminosity to the existing reverberation mapping (RM) sample, but less biased in terms of their "eigenvector 1" properties. We seek to understand the conditions under which high-ionization emission lines become dominated by a wind. Our analysis takes advantage of spectral decomposition through Independent Component Analysis (ICA) and archival UV HST spectroscopy of SDSS quasars. With these data we will clarify the needs for RM analysis of quasars with wind-dominated emission features.

Evaluating alternative offering strategies for wind producers in a pool

International Nuclear Information System (INIS)

Rahimiyan, Morteza; Morales, Juan M.; Conejo, Antonio J.

2011-01-01

Highlights: → Out-of-sample analysis allows comparing diverse offers using real-world data. → Offering the best production forecast is not optimal for a wind producer. → Stochastic programming offers lead to maximum expected profit. → Offering the best production forecast is not generally optimal for risk control. → Stochastic programming offers lead to the best tradeoff profit versus risk. -- Abstract: As wind power technology matures and reaches break-even cost, wind producers find it increasingly attractive to participate in pool markets instead of being paid feed-in tariffs. The key issue is then how a wind producer should offer in the pool markets to achieve maximum profit while controlling the variability of such profit. This paper compares two families of offering strategies based, respectively, on a naive use of wind production forecasts and on stochastic programming models. These strategies are compared through a comprehensive out-of-sample chronological analysis based on real-world data. A number of relevant conclusions are then duly drawn.

Wind resource estimation and siting of wind turbines

DEFF Research Database (Denmark)

Lundtang Petersen, Erik; Mortensen, N.G.; Landberg, L.

1994-01-01

Detailed knowledge of the characteristics of the natural wind is necessary for the design, planning and operational aspect of wind energy systems. Here, we shall only be concerned with those meteorological aspects of wind energy planning that are termed wind resource estimation. The estimation...... of the wind resource ranges from the overall estimation of the mean energy content of the wind over a large area - called regional assessment - to the prediction of the average yearly energy production of a specific wind turbine at a specific location - called siting. A regional assessment will most often...... lead to a so-called wind atlas. A precise prediction of the wind speed at a given site is essential because for aerodynamic reasons the power output of a wind turbine is proportional to the third power of the wind speed, hence even small errors in prediction of wind speed may result in large deviations...

Wind power production: from the characterisation of the wind resource to wind turbine technologies

International Nuclear Information System (INIS)

Beslin, Guy; Multon, Bernard

2016-01-01

Illustrated by graphs and tables, this article first describes the various factors and means related to the assessment of wind resource in the World, in Europe, and the factors which characterize a local wind resource. In this last respect, the authors indicate how local topography is taken into account to calculate wind speed, how time variations are taken into account (at the yearly, seasonal or daily level), the different methods used to model a local wind resource, how to assess the power recoverable by a wind turbine with horizontal axis (notion of Betz limit). In the second part, the authors present the different wind turbines, their benefits and drawbacks: vertical axis, horizontal axis (examples of a Danish-type wind turbine, of wind turbines designed for extreme conditions). Then, they address the technology of big wind turbines: evolution of technology and of commercial offer, aerodynamic characteristics of wind turbine and benefit of a varying speed (technological solutions, importance of the electric generator). They describe how to choose a wind turbine, how product lines are organised, how the power curve and energy capacity are determined. The issue of integration of wind energy into the power system is then addressed. The next part addressed the economy of wind energy production (annualized production cost, order of magnitude of wind electric power production cost). Future trends are discussed and offshore wind energy production is briefly addressed

Remoção de compostos orgânicos causadores de gosto e odor em águas de abastecimento em sistemas pós-filtros adsorvedores de carvão ativado granular.

OpenAIRE

Carolina Alves de Souza Ferreira

2009-01-01

O objetivo desta pesquisa foi o de estudar o desempenho de pós-filtros adsorvedores de carvão ativado granular de origem mineral e de origem vegetal, com relação a, principalmente, remoção de 2-metilisoborneol e trans-1,10-dimetiltrans- 9-decalol. Os ensaios experimentais foram conduzidos na estação de tratamento de água Alto da Boa Vista, empregando-se quatro filtros piloto em acrílico com diâmetro interno de 14,2 cm e 1,5 m de profundidade de meio filtrante cada, sendo dois deles preenchido...

Wind farm project economics : value of wind

Energy Technology Data Exchange (ETDEWEB)

Bills-Everett, T. [Mainstream Renewable Power, Toronto, ON (Canada)

2010-07-01

This PowerPoint presentation discussed methods of increasing the value of wind power projects. Appropriate turbine selection and layout is needed to ensure that wind resources are fully developed. Construction costs have a significant impact on project costs. The world turbine price index has not significantly fluctuated since 2006. Operating costs, and the value of wind power projects, are linked with OPEX fluctuations. Wind power projects can significantly reduce greenhouse gas (GHG) emissions. An increase in wind power capacity will reduce the overall cost of energy produced from wind power. Countries can use wind power as part of a renewable energy portfolio designed to reduce risks related to diminishing petroleum supplies. Wind power will help to ensure a global transition to renewable energy use. tabs., figs.

Wind Power Today: Wind Energy Program Highlights 2001

Energy Technology Data Exchange (ETDEWEB)

2002-05-01

Wind Power Today is an annual publication that provides an overview of the U.S. Department of Energy's Wind Energy Program accomplishments for the previous year. The purpose of Wind Power Today is to show how DOE's Wind Energy Program supports wind turbine research and deployment in hopes of furthering the advancement of wind technologies that produce clean, low-cost, reliable energy. Content objectives include: educate readers about the advantages and potential for widespread deployment of wind energy; explain the program's objectives and goals; describe the program's accomplishments in research and application; examine the barriers to widespread deployment; describe the benefits of continued research and development; facilitate technology transfer; and attract cooperative wind energy projects with industry. This 2001 edition of Wind Power Today also includes discussions about wind industry growth in 2001, how DOE is taking advantage of low wind speed regions through advancing technology, and distributed applications for small wind turbines.

Proceedings of the Canadian Wind Energy Association's 2009 wind matters conference : wind and power systems

International Nuclear Information System (INIS)

2009-01-01

This conference provided a forum for wind energy and electric power industry experts to discuss issues related to wind and power systems. An overview of wind integration studies and activities in Canada and the United States was provided. New tools and technologies for facilitating the integration of wind and improve market conditions for wind energy developers were presented. Methods of increasing wind penetration were evaluated, and technical issues related to wind interconnections throughout North America were reviewed. The conference was divided into the following 5 sessions: (1) experiences with wind integration, and lessons learned, (2) update on ongoing wind integration initiatives in Canada and the United States, (3) initiatives and tools to facilitate wind integration and market access, (4) developments in wind interconnection and grid codes, (5) wind energy and cold weather considerations, and (6) challenges to achieving the 20 per cent WindVision goal in Canada. The conference featured 21 presentations, of which 13 have been catalogued separately for inclusion in this database. refs., tabs., figs

Remoção de metais pesados tóxicos cádmio, chumbo e cromo em biofertilizante suíno utilizando macrófita aquática (Eichornia crassipes como bioindicador - DOI: 10.4025/actascitechnol.v30i1.3179

Directory of Open Access Journals (Sweden)

Affonso Celso Gonçalves Júnior

2008-05-01

Full Text Available Este trabalho objetivou avaliar a eficiência da macrófita aquática (Eichornia crassipes como bioindicador e alternativa na remoção dos metais pesados tóxicos Cd, Pb e Cr em biofertilizante de origem suína. Foi utilizado o esquema fatorial 2x4, sendo os fatores representados pelas partes da planta (aérea e raiz, e pelos quatro tratamentos. Na instalação do experimento coletou-se uma alíquota da solução de cada tratamento para determinar as concentrações iniciais dos metais e, após 30 dias de cultivo, as plantas foram retiradas, coletando-se novamente uma alíquota da solução de cada tratamento. As plantas foram separadas em parte aérea e raiz, secas e trituradas. A macrófita apresentou-se eficiente na remoção dos metais pesados, observou-se que o sistema radicular da macrófita apresentou maiores concentrações de Cd, Pb e Cr. Com este trabalho, conclui-se que a macrófita aquática (Eichornia crassipes pode ser uma alternativa para o tratamento de biofertilizante e dejetos provenientes da suinocultura

Wind power today: 1999 Wind Energy program highlights

Energy Technology Data Exchange (ETDEWEB)

Weis-Taylor, Pat

2000-04-06

Wind Power Today is an annual publication that provides an overview for the Department of Energy's Wind Energy Program. The purpose of Wind Power Today is to show how DOE's Wind Energy Program supports wind turbine research and deployment in hopes of furthering the advancement of wind technologies that produce clean, low-cost, reliable energy for the 21st century. Content objectives include: Educate readers about the advantages and potential for widespread deployment of wind energy; explain DOE wind energy program objectives and goals; describe program accomplishments in research and application; examine the barriers to widespread deployment; describe benefits of continued research and development; facilitate technology transfer; attract cooperative wind energy projects with industry.

Quality Control Algorithms for the Kennedy Space Center 50-Megahertz Doppler Radar Wind Profiler Winds Database

Science.gov (United States)

Barbre, Robert E., Jr.

2012-01-01

This paper presents the process used by the Marshall Space Flight Center Natural Environments Branch (EV44) to quality control (QC) data from the Kennedy Space Center's 50-MHz Doppler Radar Wind Profiler for use in vehicle wind loads and steering commands. The database has been built to mitigate limitations of using the currently archived databases from weather balloons. The DRWP database contains wind measurements from approximately 2.7-18.6 km altitude at roughly five minute intervals for the August 1997 to December 2009 period of record, and the extensive QC process was designed to remove spurious data from various forms of atmospheric and non-atmospheric artifacts. The QC process is largely based on DRWP literature, but two new algorithms have been developed to remove data contaminated by convection and excessive first guess propagations from the Median Filter First Guess Algorithm. In addition to describing the automated and manual QC process in detail, this paper describes the extent of the data retained. Roughly 58% of all possible wind observations exist in the database, with approximately 100 times as many complete profile sets existing relative to the EV44 balloon databases. This increased sample of near-continuous wind profile measurements may help increase launch availability by reducing the uncertainty of wind changes during launch countdown

Wind energy. To produce electricity with the wind

International Nuclear Information System (INIS)

Bareau, Helene

2015-11-01

This guide addresses the different aspects of wind-based power generation. It outlines the role of wind energy to meet objectives related to the share of renewable energies in the French energy mix, that wind energy is actually replacing fossil energies, that it is based on local resources within higher safety and less wastage, that current advances are made to integrate wind energy production into the grid, and that it is a solution to diversify energy production. Some figures are presented and commented, regarding onshore wind energy production in France, the location of wind farms, and wind energy production in comparison with other renewable sources. The operation of a wind turbine is described and the different types of wind turbines are evoked. The issue of wind farm planning with citizen participation is addressed: regional planning, studies of pre-feasibility for location selection, procedure, and content of the impact study (radars, fauna and flora, landscapes, safety, health). Other features are outlined: a planned dismantling, and a globally favourable perception. The next part addresses offshore wind energy: the interesting potential of stronger and more reliable wind at sea (European situation, French opportunities, elements comprised in an offshore wind farm), impacts (on marine ecosystems, on neighbouring localities, and interests for visitors). Economic aspects are then addressed: cost and profitability, economic spin-offs, and perspectives. The last part concerns individuals and the possibilities to participate to wind farm projects or to invest in small wind turbines with some prerequisites (constant and steady winds, installation assessment, required expertise, indispensable preliminary steps, costs, aids and profitability)

WIND observations of coherent electrostatic waves in the solar wind

Directory of Open Access Journals (Sweden)

A. Mangeney

Full Text Available The time domain sampler (TDS experiment on WIND measures electric and magnetic wave forms with a sampling rate which reaches 120 000 points per second. We analyse here observations made in the solar wind near the Lagrange point L1. In the range of frequencies above the proton plasma frequency f_pi and smaller than or of the order of the electron plasma frequency f_pe, TDS observed three kinds of electrostatic (e.s. waves: coherent wave packets of Langmuir waves with frequencies f ~ f_pe, coherent wave packets with frequencies in the ion acoustic range f_pi < f < f_pe, and more or less isolated non-sinusoidal spikes lasting less than 1 ms. We confirm that the observed frequency of the low frequency (LF ion acoustic wave packets is dominated by the Doppler effect: the wavelengths are short, 10 to 50 electron Debye lengths λ_D. The electric field in the isolated electrostatic structures (IES and in the LF wave packets is more or less aligned with the solar wind magnetic field. Across the IES, which have a spatial width of the order of ~ 25λ_D, there is a small but finite electric potential drop, implying an average electric field generally directed away from the Sun. The IES wave forms, which have not been previously reported in the solar wind, are similar, although with a smaller amplitude, to the weak double layers observed in the auroral regions, and to the electrostatic solitary waves observed in other regions in the magnetosphere. We have also studied the solar wind conditions which favour the occurrence of the three kinds of waves: all these e.s. waves are observed more or less continuously in the whole solar wind (except in the densest regions where a parasite prevents the TDS observations. The type (wave packet or IES of the observed LF waves is mainly determined

Modeling of the UAE Wind Turbine for Refinement of FAST{_}AD

Energy Technology Data Exchange (ETDEWEB)

Jonkman, J. M.

2003-12-01

The Unsteady Aerodynamics Experiment (UAE) research wind turbine was modeled both aerodynamically and structurally in the FAST{_}AD wind turbine design code, and its response to wind inflows was simulated for a sample of test cases. A study was conducted to determine why wind turbine load magnitude discrepancies-inconsistencies in aerodynamic force coefficients, rotor shaft torque, and out-of-plane bending moments at the blade root across a range of operating conditions-exist between load predictions made by FAST{_}AD and other modeling tools and measured loads taken from the actual UAE wind turbine during the NASA-Ames wind tunnel tests. The acquired experimental test data represent the finest, most accurate set of wind turbine aerodynamic and induced flow field data available today. A sample of the FAST{_}AD model input parameters most critical to the aerodynamics computations was also systematically perturbed to determine their effect on load and performance predictions. Attention was focused on the simpler upwind rotor configuration, zero yaw error test cases. Inconsistencies in input file parameters, such as aerodynamic performance characteristics, explain a noteworthy fraction of the load prediction discrepancies of the various modeling tools.

Soil wind erosion in ecological olive trees in the Tabernas desert (southeastern Spain): a wind tunnel experiment

Science.gov (United States)

Asensio, Carlos; Lozano, Francisco Javier; Gallardo, Pedro; Giménez, Antonio

2016-08-01

Wind erosion is a key component of the soil degradation processes. The purpose of this study is to find out the influence of material loss from wind on soil properties for different soil types and changes in soil properties in olive groves when they are tilled. The study area is located in the north of the Tabernas Desert, in the province of Almería, southeastern Spain. It is one of the driest areas in Europe, with a semiarid thermo-Mediterranean type of climate. We used a new wind tunnel model over three different soil types (olive-cropped Calcisol, Cambisol and Luvisol) and studied micro-plot losses and deposits detected by an integrated laser scanner. We also studied the image processing possibilities for examining the particles attached to collector plates located at the end of the tunnel to determine their characteristics and whether they were applicable to the setup. Samples collected in the traps at the end of the tunnel were analyzed. We paid special attention to the influence of organic carbon, carbonate and clay contents because of their special impact on soil crusting and the wind-erodible fraction. A principal components analysis (PCA) was carried out to find any relations on generated dust properties and the intensity and behavior of those relationships. Component 1 separated data with high N and OC contents from samples high in fine silt, CO3= and available K content. Component 2 separated data with high coarse silt and clay contents from data with high fine sand content. Component 3 was an indicator of available P2O5 content. Analysis of variance (ANOVA) was carried out to analyze the effect of soil type and sampling height on different properties of trapped dust. Calculations based on tunnel data showed overestimation of erosion in soil types and calculation of the fraction of soil erodible by wind done by other authors for Spanish soils. As the highest loss was found in Cambisols, mainly due to the effect on soil crusting and the wind

Wind power integration : From individual wind turbine to wind park as a power plant

NARCIS (Netherlands)

Zhou, Y.

2009-01-01

As power capacities of single wind turbine, single wind park and total wind power installation are continuously increasing, the wind power begins to challenge the safety operation of the power system. This thesis focuses on the grid integration aspects such as the dynamic behaviours of wind power

An evaluation of the WindEye wind lidar

DEFF Research Database (Denmark)

Dellwik, Ebba; Sjöholm, Mikael; Mann, Jakob

Prevision of the wind field by remote sensing wind lidars has the potential to improve the performance of wind turbines. The functionality of a WindEye lidar developed by Windar Photonics A/S (Denmark) for the wind energy market was tested in a two months long field experiment. The WindEye sensor...... with a high accuracy during the whole campaign....

Estádio de maturação de frutos e remoção física da sarcotesta na produção de mudas de mamão

OpenAIRE

Aniela Pilar Campos de Melo; Alexsander Seleguini

2013-01-01

O uso de mudas de qualidade é primordial para o sucesso na implantação do cultivo domamoeiro. Entretanto, a presença da sarcotesta nas sementes e a dormência pós-colheita defrutos podem prejudicar a produção de mudas em escala comercial. Desta forma, em casa-devegetação,avaliou-se na emergência e no desenvolvimento de mudas de mamoeiro os efeitos dacombinação entre o estádio de maturação de frutos e métodos físicos de remoção da sarcotesta.Adotou-se o delineamento inteiramente casualizado, em...

Wind Structure and Wind Loading

DEFF Research Database (Denmark)

Brorsen, Michael

The purpose of this note is to provide a short description of wind, i.e. of the flow in the atmosphere of the Earth and the loading caused by wind on structures. The description comprises: causes to the generation of windhe interaction between wind and the surface of the Earthhe stochastic nature...

An Appropriate Wind Model for Wind Integrated Power Systems Reliability Evaluation Considering Wind Speed Correlations

Directory of Open Access Journals (Sweden)

Rajesh Karki

2013-02-01

Full Text Available Adverse environmental impacts of carbon emissions are causing increasing concerns to the general public throughout the world. Electric energy generation from conventional energy sources is considered to be a major contributor to these harmful emissions. High emphasis is therefore being given to green alternatives of energy, such as wind and solar. Wind energy is being perceived as a promising alternative. This source of energy technology and its applications have undergone significant research and development over the past decade. As a result, many modern power systems include a significant portion of power generation from wind energy sources. The impact of wind generation on the overall system performance increases substantially as wind penetration in power systems continues to increase to relatively high levels. It becomes increasingly important to accurately model the wind behavior, the interaction with other wind sources and conventional sources, and incorporate the characteristics of the energy demand in order to carry out a realistic evaluation of system reliability. Power systems with high wind penetrations are often connected to multiple wind farms at different geographic locations. Wind speed correlations between the different wind farms largely affect the total wind power generation characteristics of such systems, and therefore should be an important parameter in the wind modeling process. This paper evaluates the effect of the correlation between multiple wind farms on the adequacy indices of wind-integrated systems. The paper also proposes a simple and appropriate probabilistic analytical model that incorporates wind correlations, and can be used for adequacy evaluation of multiple wind-integrated systems.

Transient LES of an offshore wind turbine

Directory of Open Access Journals (Sweden)

L. Vollmer

2017-12-01

Full Text Available The estimation of the cost of energy of offshore wind farms has a high uncertainty, which is partly due to the lacking accuracy of information on wind conditions and wake losses inside of the farm. Wake models that aim to reduce the uncertainty by modeling the wake interaction of turbines for various wind conditions need to be validated with measurement data before they can be considered as a reliable estimator. In this paper a methodology that enables a direct comparison of modeled with measured flow data is evaluated. To create the simulation data, a model chain including a mesoscale model, a large-eddy-simulation (LES model and a wind turbine model is used. Different setups are compared to assess the capability of the method to reproduce the wind conditions at the hub height of current offshore wind turbines. The 2-day-long simulation of the ambient wind conditions and the wake simulation generally show good agreements with data from a met mast and lidar measurements, respectively. Wind fluctuations due to boundary layer turbulence and synoptic-scale motions are resolved with a lower representation of mesoscale fluctuations. Advanced metrics to describe the wake shape and development are derived from simulations and measurements but a quantitative comparison proves to be difficult due to the scarcity and the low sampling rate of the available measurement data. Due to the implementation of changing synoptic wind conditions in the LES, the methodology could also be beneficial for case studies of wind farm performance or wind farm control.

Remoção de microcistina-LR de águas eutrofizadas por clarificação e filtração seguidas de adsorção em carvão ativado granular

OpenAIRE

Guerra,Alaine de Brito; Tonucci,Marina Caldeira; Ceballos,Beatriz Susana Ovruski de; Guimarães,Hindria Renally Cavalcanti; Lopes,Wilton Silva; Aquino,Sérgio Francisco de; Libânio,Marcelo

2015-01-01

RESUMO Usualmente, o tratamento convencional de águas com altas densidades de cianobactérias e concentração de cianotoxinas não garante efluente consoante o padrão de potabilidade vigente (1,0 µg.L-1 de microcistina). Etapas adicionais fazem-se necessárias, destacando-se a adsorção por carvão ativado granular ou pulverizado. Neste contexto, o objetivo geral deste trabalho foi avaliar em escala de bancada a remoção de microcistina em água natural por adsorção em colunas de carvão ativado granu...

Wind energy

International Nuclear Information System (INIS)

Anon.

1992-01-01

This chapter discusses the role wind energy may have in the energy future of the US. The topics discussed in the chapter include historical aspects of wind energy use, the wind energy resource, wind energy technology including intermediate-size and small wind turbines and intermittency of wind power, public attitudes toward wind power, and environmental, siting and land use issues

Strategic wind power trading considering rival wind power production

DEFF Research Database (Denmark)

Exizidis, Lazaros; Kazempour, Jalal; Pinson, Pierre

2016-01-01

In an electricity market with high share of wind power, it is expected that wind power producers may exercise market power. However, wind producers have to cope with wind’s uncertain nature in order to optimally offer their generation, whereas in a market with more than one wind producers, uncert...... depending on the rival’s wind generation, given that its own expected generation is not high. Finally, as anticipated, expected system cost is higher when both wind power producers are expected to have low wind power generation......In an electricity market with high share of wind power, it is expected that wind power producers may exercise market power. However, wind producers have to cope with wind’s uncertain nature in order to optimally offer their generation, whereas in a market with more than one wind producers......, uncertainty of rival wind power generation should also be considered. Under this context, this paper addresses the impact of rival wind producers on the offering strategy and profits of a pricemaker wind producer. A stochastic day-ahead market setup is considered, which optimizes the day-ahead schedules...

Modelling Wind for Wind Farm Layout Optimization Using Joint Distribution of Wind Speed and Wind Direction

DEFF Research Database (Denmark)

Feng, Ju; Shen, Wen Zhong

2015-01-01

Reliable wind modelling is of crucial importance for wind farm development. The common practice of using sector-wise Weibull distributions has been found inappropriate for wind farm layout optimization. In this study, we propose a simple and easily implementable method to construct joint distribu...

LIDAR Wind Speed Measurements of Evolving Wind Fields

Energy Technology Data Exchange (ETDEWEB)

Simley, E.; Pao, L. Y.

2012-07-01

Light Detection and Ranging (LIDAR) systems are able to measure the speed of incoming wind before it interacts with a wind turbine rotor. These preview wind measurements can be used in feedforward control systems designed to reduce turbine loads. However, the degree to which such preview-based control techniques can reduce loads by reacting to turbulence depends on how accurately the incoming wind field can be measured. Past studies have assumed Taylor's frozen turbulence hypothesis, which implies that turbulence remains unchanged as it advects downwind at the mean wind speed. With Taylor's hypothesis applied, the only source of wind speed measurement error is distortion caused by the LIDAR. This study introduces wind evolution, characterized by the longitudinal coherence of the wind, to LIDAR measurement simulations to create a more realistic measurement model. A simple model of wind evolution is applied to a frozen wind field used in previous studies to investigate the effects of varying the intensity of wind evolution. LIDAR measurements are also evaluated with a large eddy simulation of a stable boundary layer provided by the National Center for Atmospheric Research. Simulation results show the combined effects of LIDAR errors and wind evolution for realistic turbine-mounted LIDAR measurement scenarios.

Spatial variability of soil chemical properties after coffee tree removal Variabilidade espacial dos atributos químicos do solo após remoção de cafezal

Directory of Open Access Journals (Sweden)

Sidney Rosa Vieira

2009-10-01

Full Text Available Assessing the spatial variability of soil chemical properties has become an important aspect of soil management strategies with a view to higher crop yields with minimal environmental degradation. This study was carried out at the Centro Experimental of the Instituto Agronomico, in Campinas, São Paulo, Brazil. The aim was to characterize the spatial variability of chemical properties of a Rhodic Hapludox on a recently bulldozer-cleaned area after over 30 years of coffee cultivation. Soil samples were collected in a 20 x 20 m grid with 36 sampling points across a 1 ha area in the layers 0.0-0.2 and 0.2-0.4 m to measure the following chemical properties: pH, organic matter, K+, P, Ca2+, Mg2+, potential acidity, NH4-N, and NO3-N. Descriptive statistics were applied to assess the central tendency and dispersion moments. Geostatistical methods were applied to evaluate and to model the spatial variability of variables by calculating semivariograms and kriging interpolation. Spatial dependence patterns defined by spherical model adjusted semivariograms were made for all cited soil properties. Moderate to strong degrees of spatial dependence were found between 31 and 60 m. It was still possible to map soil spatial variability properties in the layers 0-20 cm and 20-40 cm after plant removal with bulldozers.A avaliação da variabilidade espacial dos atributos químicos do solo tem se tornado importante ferramenta na determinação de estratégias de manejo que visam aumentar a produtividade agrícola com menor degradação ambiental. O presente trabalho foi realizado no Centro Experimental Central do Instituto Agronômico, localizado em Campinas/SP, com o objetivo de caracterizar a variabilidade espacial dos atributos químicos de um Latossolo Vermelho após a remoção de um cafezal, cultivado por mais de 30 anos, com trator de esteira. As amostras de solo foram coletadas em grade georreferenciada de 20 x 20 m, totalizando 36 pontos nas camadas de 0

Wind Energy

International Nuclear Information System (INIS)

Rodriguez D, J.M.

1998-01-01

The general theory of the wind energy conversion systems is presented. The availability of the wind resource in Colombia and the ranges of the speed of the wind in those which is possible economically to use the wind turbines are described. It is continued with a description of the principal technological characteristics of the wind turbines and are split into wind power and wind-powered pumps; and its use in large quantities grouped in wind farms or in autonomous systems. Finally, its costs and its environmental impact are presented

Wind direction correlated measurements of radon and radon progeny in atmosphere: a method for radon source identification

International Nuclear Information System (INIS)

Akber, R.A.; Pfitzner, J.; Johnston, A.

1994-01-01

This paper describes the basic principles and methodology of a wind direction correlated measurement technique which is used to distinguish the mine-related and background components of radon and radon progeny concentrations in the vicinity of the ERA Ranger Uranium Mine. Simultaneous measurements of atmospheric radon and radon progeny concentrations and wind speed and direction were conducted using automatic sampling stations. The data were recorded as a time series of half hourly averages and grouped into sixteen 22.5 degrees wind sectors. The sampling interval and the wind sector width were chosen considering wind direction variability (σ θ ) over the sampling time interval. The data were then analysed for radon and radon progeny concentrations in each wind sector. Information about the wind frequency wind speed seasonal and diurnal variations in wind direction and radon concentrations was required for proper data analysis and interpretation of results. A comparison with model-based estimates for an identical time period shows agreement within about a factor of two between the two methods. 15 refs., 1 tab., 5 figs

Flying with the wind: Scale dependency of speed and direction measurements in modelling wind support in avian flight

Science.gov (United States)

Safi, Kamran; Kranstauber, Bart; Weinzierl, Rolf P.; Griffin, Larry; Reese, Eileen C.; Cabot, David; Cruz, Sebastian; Proaño, Carolina; Takekawa, John Y.; Newman, Scott H.; Waldenström, Jonas; Bengtsson, Daniel; Kays, Roland; Wikelski, Martin; Bohrer, Gil

2013-01-01

Background: Understanding how environmental conditions, especially wind, influence birds' flight speeds is a prerequisite for understanding many important aspects of bird flight, including optimal migration strategies, navigation, and compensation for wind drift. Recent developments in tracking technology and the increased availability of data on large-scale weather patterns have made it possible to use path annotation to link the location of animals to environmental conditions such as wind speed and direction. However, there are various measures available for describing not only wind conditions but also the bird's flight direction and ground speed, and it is unclear which is best for determining the amount of wind support (the length of the wind vector in a bird’s flight direction) and the influence of cross-winds (the length of the wind vector perpendicular to a bird’s direction) throughout a bird's journey.Results: We compared relationships between cross-wind, wind support and bird movements, using path annotation derived from two different global weather reanalysis datasets and three different measures of direction and speed calculation for 288 individuals of nine bird species. Wind was a strong predictor of bird ground speed, explaining 10-66% of the variance, depending on species. Models using data from different weather sources gave qualitatively similar results; however, determining flight direction and speed from successive locations, even at short (15 min intervals), was inferior to using instantaneous GPS-based measures of speed and direction. Use of successive location data significantly underestimated the birds' ground and airspeed, and also resulted in mistaken associations between cross-winds, wind support, and their interactive effects, in relation to the birds' onward flight.Conclusions: Wind has strong effects on bird flight, and combining GPS technology with path annotation of weather variables allows us to quantify these effects for

Evaluation of wind farm efficiency and wind turbine wakes at the Nysted offshore wind farm

DEFF Research Database (Denmark)

Barthelmie, Rebecca Jane; Jensen, L.E.

2010-01-01

Here, we quantify relationships between wind farm efficiency and wind speed, direction, turbulence and atmospheric stability using power output from the large offshore wind farm at Nysted in Denmark. Wake losses are, as expected, most strongly related to wind speed variations through the turbine...... thrust coefficient; with direction, atmospheric stability and turbulence as important second order effects. While the wind farm efficiency is highly dependent on the distribution of wind speeds and wind direction, it is shown that the impact of turbine spacing on wake losses and turbine efficiency can...... be quantified, albeit with relatively large uncertainty due to stochastic effects in the data. There is evidence of the ‘deep array effect’ in that wake losses in the centre of the wind farm are under-estimated by the wind farm model WAsP, although overall efficiency of the wind farm is well predicted due...

Wind Power Today: 2000 Wind Energy Program Highlights

Energy Technology Data Exchange (ETDEWEB)

Weis-Taylor, W.

2001-05-08

Wind Power Today is an annual publication that provides an overview of the U.S. Department of Energy's Wind Energy Program. The purpose of Wind Power Today is to show how DOE's Wind Energy Program supports wind turbine research and deployment in hopes of furthering the advancement of wind technologies that produce clean, low-cost, reliable energy. Content objectives include: educate readers about the advantages and potential for widespread deployment of wind energy; explain the program's objectives and goals; describe the program's accomplishments in research and application; examine the barriers to widespread deployment; describe the benefits of continued research and development; facilitate technology transfer; and attract cooperative wind energy projects with industry.

Utilização de surfactantes, na polpação kraft de madeira de eucalipto, como auxiliar na remoção de extrativos lipofílicos Surfactant utilization in kraft pulping of eucalyptus wood to improve lipophilic extractives removal

Directory of Open Access Journals (Sweden)

Deusanilde de Jesus Silva

2004-12-01

Full Text Available Problemas de deposição de "pitch" em fábricas de celulose e de papel são atribuídos aos extrativos lipofílicos existentes na madeira. Uma das maneiras mais eficientes de controlar essa deposição é através da remoção de seus precursores do sistema, logo que possível, nas etapas de cozimento, lavagem da polpa marrom e pré-deslignificação com oxigênio. O uso de surfactantes como aditivos da polpação tem sido investigado, mas há grande deficiência de informações técnicas, e a aplicação industrial é, ainda, incipiente. A proposta deste trabalho foi analisar a viabilidade de minimizar a deposição de "pitch", intensificando a remoção de suas substâncias precursoras na etapa de polpação pelo uso de tensoativos sintéticos com propriedades umectantes e solubilizantes. Foram testados 20 princípios ativos de surfactantes em cozimento kraft convencional de madeira de eucalipto. Os resultados, alguns estatisticamente significativos, apontaram redução do teor de substâncias lipofílicas na polpa marrom. Foi observado que a remoção dos extrativos lipofílicos da madeira é afetada, inversamente, pelo teor de óxido de eteno na molécula do surfactante. Outros parâmetros de cozimento, como deslignificação, rendimento, teor de rejeitos e viscosidade da polpa, foram também avaliados.Extractives are pitch precursors and may decrease pulping efficiency and affect pulp quality. Probably, the most efficient way to minimize pitch problems is to remove their precursors from the system during cooking, pulp washing and oxygen delignification. Use of surfactants as pulping additives has been investigated but technical information is deficient and industrial application is very incipient. The objective of this study was to analyze the performance of different surfactants as additives for kraft pulping of Eucalyptus wood. Twenty surfactants with different basic chemical structures were used. The results demonstrated that

Advancements in Wind Integration Study Data Modeling: The Wind Integration National Dataset (WIND) Toolkit; Preprint

Energy Technology Data Exchange (ETDEWEB)

Draxl, C.; Hodge, B. M.; Orwig, K.; Jones, W.; Searight, K.; Getman, D.; Harrold, S.; McCaa, J.; Cline, J.; Clark, C.

2013-10-01

Regional wind integration studies in the United States require detailed wind power output data at many locations to perform simulations of how the power system will operate under high-penetration scenarios. The wind data sets that serve as inputs into the study must realistically reflect the ramping characteristics, spatial and temporal correlations, and capacity factors of the simulated wind plants, as well as be time synchronized with available load profiles. The Wind Integration National Dataset (WIND) Toolkit described in this paper fulfills these requirements. A wind resource dataset, wind power production time series, and simulated forecasts from a numerical weather prediction model run on a nationwide 2-km grid at 5-min resolution will be made publicly available for more than 110,000 onshore and offshore wind power production sites.

Wind Climate Parameters for Wind Turbine Fatigue Load Assessment

DEFF Research Database (Denmark)

Toft, Henrik Stensgaard; Svenningsen, Lasse; Moser, Wolfgang

2016-01-01

Site-specific assessment of wind turbine design requires verification that the individual wind turbine components can survive the site-specific wind climate. The wind turbine design standard, IEC 61400-1 (third edition), describes how this should be done using a simplified, equivalent wind climate...... climate required by the current design standard by comparing damage equivalent fatigue loads estimated based on wind climate parameters for each 10 min time-series with fatigue loads estimated based on the equivalent wind climate parameters. Wind measurements from Boulder, CO, in the United States...

European Wind Atlas and Wind Resource Research in Denmark

DEFF Research Database (Denmark)

Mortensen, Niels Gylling

to estimate the actual wind climate at any specific site and height within this region. The Danish and European Wind Atlases are examples of how the wind atlas methodology can be employed to estimate the wind resource potential for a country or a sub-continent. Recently, the methodology has also been used...... - from wind measurements at prospective sites to wind tunnel simulations and advanced flow modelling. Among these approaches, the wind atlas methodology - developed at Ris0 National Laboratory over the last 25 years - has gained widespread recognition and is presently considered by many as the industry......-standard tool for wind resource assessment and siting of wind turbines. The PC-implementation of the methodology, the Wind Atlas Analysis and Application Program (WAsP), has been applied in more than 70 countries and territories world-wide. The wind atlas methodology is based on physical descriptions and models...

When real life wind speed exceeds design wind assumptions

Energy Technology Data Exchange (ETDEWEB)

Winther-Jensen, M; Joergensen, E R [Risoe National Lab., Roskilde (Denmark)

1999-03-01

Most modern wind turbines are designed according to a standard or a set of standards to withstand the design loads with a defined survival probability. Mainly the loads are given by the wind conditions on the site defining the `design wind speeds`, normally including extreme wind speeds given as an average and a peak value. The extreme wind speeds are normally (e.g. in the upcoming IEC standard for wind turbine safety) defined as having a 50-year recurrence period. But what happens when the 100 or 10,000 year wind situation hits a wind turbine? Results on wind turbines of wind speeds higher than the extreme design wind speeds are presented based on experiences especially from the State of Gujarat in India. A description of the normal approach of designing wind turbines in accordance with the standards in briefly given in this paper with special focus on limitations and built-in safety levels. Based on that, other possibilities than just accepting damages on wind turbines exposed for higher than design wind speeds are mentioned and discussed. The presentation does not intend to give the final answer to this problem but is meant as an input to further investigations and discussions. (au)

Assessment of the National Wind Coordinating Collaborative: Addressing Environmental and Siting Issues Associated with Wind Energy Development

Energy Technology Data Exchange (ETDEWEB)

Van Cleve, Frances B.; States, Jennifer C.

2010-11-09

The National Wind Coordinating Collaborative (NWCC) is a consensus-based stakeholder group comprised of representatives from the utility, wind industry, environmental, consumer, regulatory, power marketer, agricultural, tribal, economic development, and state and federal government sectors. The purpose of the NWCC is to support the development of an environmentally, economically, and politically sustainable commercial market for wind power (NWCC 2010). The NWCC has been funded by the U.S. Department of Energy (DOE) since its inception in 1994. In order to evaluate the impact of the work of the NWCC and how this work aligns with DOE’s strategic priorities, DOE tasked Pacific Northwest National Laboratory (PNNL) to conduct a series of informal interviews with a small sample of those involved with NWCC.

Wind Turbine Gearbox Oil Filtration and Condition Monitoring

Energy Technology Data Exchange (ETDEWEB)

Sheng, Shuangwen

2015-10-25

This is an invited presentation for a pre-conference workshop, titled advances and opportunities in lubrication: wind turbine, at the 2015 Society of Tribologists and Lubrication Engineers (STLE) Tribology Frontiers Conference held in Denver, CO. It gives a brief overview of wind turbine gearbox oil filtration and condition monitoring by highlighting typical industry practices and challenges. The presentation starts with an introduction by covering recent growth of global wind industry, reliability challenges, benefits of oil filtration and condition monitoring, and financial incentives to conduct wind operation and maintenance research, which includes gearbox oil filtration and condition monitoring work presented herein. Then, the presentation moves on to oil filtration by stressing the benefits of filtration, discussing typical main- and offline-loop practices, highlighting important factors considered when specifying a filtration system, and illustrating real-world application challenges through a cold-start example. In the next section on oil condition monitoring, a discussion on oil sample analysis, oil debris monitoring, oil cleanliness measurements and filter analysis is given based on testing results mostly obtained by and at NREL, and by pointing out a few challenges with oil sample analysis. The presentation concludes with a brief touch on future research and development (R and D) opportunities. It is hoping that the information presented can inform the STLE community to start or redirect their R and D work to help the wind industry advance.

Analysis of nucleation events in the European boundary layer using the regional aerosol–climate model REMO-HAM with a solar radiation-driven OH-proxy

Directory of Open Access Journals (Sweden)

J.-P. Pietikäinen

2014-11-01

Full Text Available This work describes improvements in the regional aerosol–climate model REMO-HAM in order to simulate more realistically the process of atmospheric new particle formation (NPF. A new scheme was implemented to simulate OH radical concentrations using a proxy approach based on observations and also accounting for the effects of clouds upon OH concentrations. Second, the nucleation rate calculation was modified to directly simulate the formation rates of 3 nm particles, which removes some unnecessary steps in the formation rate calculations used earlier in the model. Using the updated model version, NPF over Europe was simulated for the periods 2003–2004 and 2008–2009. The statistics of the simulated particle formation events were subsequently compared to observations from 13 ground-based measurement sites. The new model shows improved agreement with the observed NPF rates compared to former versions and can simulate the event statistics realistically for most parts of Europe.

He II lambda-4686 in Eta Carinae: Collapse of the Wind-Wind Collision Region During Periastron Passage

Science.gov (United States)

Teodoro, M.; Damineli, A.; Arias, J. I.; DeAraujo, F. X.; Barba, R. H.; Corcoran, M. F.; Fernandes, M. Borges; Fernandez-Lajus, E.; Fraga, L.; Gamen, R. C.;

3D WindScanner lidar measurements of wind and turbulence around wind turbines, buildings and bridges

Science.gov (United States)

Mikkelsen, T.; Sjöholm, M.; Angelou, N.; Mann, J.

2017-12-01

WindScanner is a distributed research infrastructure developed at DTU with the participation of a number of European countries. The research infrastructure consists of a mobile technically advanced facility for remote measurement of wind and turbulence in 3D. The WindScanners provide coordinated measurements of the entire wind and turbulence fields, of all three wind components scanned in 3D space. Although primarily developed for research related to on- and offshore wind turbines and wind farms, the facility is also well suited for scanning turbulent wind fields around buildings, bridges, aviation structures and of flow in urban environments. The mobile WindScanner facility enables 3D scanning of wind and turbulence fields in full scale within the atmospheric boundary layer at ranges from 10 meters to 5 (10) kilometers. Measurements of turbulent coherent structures are applied for investigation of flow pattern and dynamical loads from turbines, building structures and bridges and in relation to optimization of the location of, for example, wind farms and suspension bridges. This paper presents our achievements to date and reviews briefly the state-of-the-art of the WindScanner measurement technology with examples of uses for wind engineering applications.

Wind Turbine Converter Control Interaction with Complex Wind Farm Systems

DEFF Research Database (Denmark)

Kocewiak, Lukasz Hubert; Hjerrild, Jesper; Bak, Claus Leth

2013-01-01

. The same wind turbine converter control strategy is evaluated in two different wind farms. It is emphasised that the grid-side converter controller should be characterised by sufficient harmonic/noise rejection and adjusted depending on wind farms to which it is connected. Various stability indices......This study presents wind turbine converter stability analysis of wind farms in frequency domain. The interaction between the wind turbine control system and the wind farm structure in wind farms is deeply investigated. Two wind farms (i.e. Horns Rev II and Karnice) are taken into consideration...... in this study. It is shown that wind farm components, such as long high-voltage alternating current cables and park transformers, can introduce significant low-frequency series resonances seen from the wind turbine terminals that can affect wind turbine control system operation and overall wind farm stability...

Early stages of wind wave and drift current generation under non-stationary wind conditions.

Science.gov (United States)

Robles-Diaz, Lucia; Ocampo-Torres, Francisco J.; Branger, Hubert

2016-04-01

Generation and amplification mechanisms of ocean waves are well understood under constant wind speed or limited fetch conditions. Under these situations, the momentum and energy transfers from air to water are also quite well known. However during the wind field evolution over the ocean, we may observe sometime high wind acceleration/deceleration situations (e.g. Mexican Tehuano or Mediterranean Mistral wind systems). The evolution of wave systems under these conditions is not well understood. The purpose of these laboratory experiments is to better understand the early stages of water-waves and surface-drift currents under non-stationary wind conditions and to determine the balance between transfers creating waves and surface currents during non-equilibrium situations. The experiments were conducted in the Institut Pythéas wind-wave facility in Marseille-France. The wave tank is 40 m long, 2.7 m wide and 1 m deep. The air section is 50 m long, 3 m wide and 1.8 m height. We used 11 different resistive wave-gauges located along the tank. The momentum fluxes in the air column were estimated from single and X hot-film anemometer measurements. The sampling frequency for wind velocity and surface displacement measurements was 256 Hz. Water-current measurements were performed with a profiling velocimeter. This device measures the first 3.5 cm of the water column with a frequency rate of 100Hz. During the experiments, the wind intensity was abruptly modified with a constant acceleration and deceleration over time. We observed that wind drag coefficient values for accelerated wind periods are lower than the ones reported in previous studies for constant wind speed (Large and Pond 1981; Ocampo-Torres et al. 2010; Smith 1980; Yelland and Taylor 1996). This is probably because the turbulent boundary layer is not completely developed during the increasing-wind sequence. As it was reported in some theoretical studies (Miles 1957; Phillips 1957; Kahma and Donelan 1988), we

The Wind Integration National Dataset (WIND) toolkit (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Caroline Draxl: NREL

2014-01-01

Regional wind integration studies require detailed wind power output data at many locations to perform simulations of how the power system will operate under high penetration scenarios. The wind datasets that serve as inputs into the study must realistically reflect the ramping characteristics, spatial and temporal correlations, and capacity factors of the simulated wind plants, as well as being time synchronized with available load profiles.As described in this presentation, the WIND Toolkit fulfills these requirements by providing a state-of-the-art national (US) wind resource, power production and forecast dataset.

Wind power

International Nuclear Information System (INIS)

Gipe, P.

2007-01-01

This book is a translation of the edition published in the USA under the title of ''wind power: renewable energy for home, farm and business''. In the wake of mass blackouts and energy crises, wind power remains a largely untapped resource of renewable energy. It is a booming worldwide industry whose technology, under the collective wing of aficionados like author Paul Gipe, is coming of age. Wind Power guides us through the emergent, sometimes daunting discourse on wind technology, giving frank explanations of how to use wind technology wisely and sound advice on how to avoid common mistakes. Since the mid-1970's, Paul Gipe has played a part in nearly every aspect of wind energy development from installing small turbines to promoting wind energy worldwide. As an American proponent of renewable energy, Gipe has earned the acclaim and respect of European energy specialists for years, but his arguments have often fallen on deaf ears at home. Today, the topic of wind power is cropping up everywhere from the beaches of Cape Cod to the Oregon-Washington border, and one wind turbine is capable of producing enough electricity per year to run 200 average American households. Now, Paul Gipe is back to shed light on this increasingly important energy source with a revised edition of Wind Power. Over the course of his career, Paul Gipe has been a proponent, participant, observer, and critic of the wind industry. His experience with wind has given rise to two previous books on the subject, Wind Energy Basics and Wind Power for Home and Business, which have sold over 50,000 copies. Wind Power for Home and Business has become a staple for both homeowners and professionals interested in the subject, and now, with energy prices soaring, interest in wind power is hitting an all-time high. With chapters on output and economics, Wind Power discloses how much you can expect from each method of wind technology, both in terms of energy and financial savings. The book updated models

Marine wind data presentation using wind transition matrix

Digital Repository Service at National Institute of Oceanography (India)

Mascarenhas, A.J.; Gouveia, A.D.; Desai, R.G.P.

One of the methods to simulate the random wind behaviour through time is to use historical wind data presented in the form of wind transition matrix. Here it is assumed that, the probability that the wind will shift from one direction to another...

Remoção mecânica de plantas aquáticas: análise econômica e operacional Mechanical removal of aquatic weeds: operational and economic analysis

Directory of Open Access Journals (Sweden)

U.R. Antuniassi

2002-01-01

Full Text Available A remoção de plantas aquáticas tem sido utilizada como opção ao controle químico e biológico, em razão de restrições ambientais em algumas regiões brasileiras. O objetivo deste trabalho foi desenvolver um modelo para análise econômica e operacional da remoção mecânica de plantas aquáticas, visando realizar estudo econômico comparativo com o controle químico. A operação foi estudada num reservatório de uma usina de bombeamento em Barra do Piraí-RJ. O sistema consiste de retroescavadeiras instaladas em balsas, usadas para cortar as plantas e liberá-las no fluxo de água. Antes da tomada d'água existe uma barreira flutuante que intercepta as plantas, as quais são removidas por um guindaste fixo nas margens. As plantas são armazenadas por algum tempo e depois descartadas. Existe, ainda, um sistema de limpeza das grades da tomada d'água. Dados do volume total de plantas descartadas foram coletados durante 14 meses, assim como foi avaliado o volume de biomassa produzido por área das principais espécies infestantes. A empreiteira que administra o serviço forneceu planilhas de custos e outro parâmetros operacionais. Um modelo foi desenvolvido para calcular custos por hectare de plantas removidas. Os resultados mostraram custo médio mensal de US$ 17.780,28 por hectare. Apesar do alto custo, o sistema de remoção demonstrou capacidade de controlar apenas 4,1% da área infestada no reservatório, na época da coleta dos dados. Simulando dados de uma aplicação de glyphosate, o controle químico custaria apenas 0,23% do custo da remoção. Análises de sensibilidade mostraram que a compactação das plantas para transporte, o volume de plantas produzidas por área e o custo do transporte são os parâmetros principais para a otimização.Mechanical removal of aquatic weeds has been an option to biological and chemical control because of environmental restrictions in some places in Brazil. The objective of this study was to

Wind power forecast error smoothing within a wind farm

International Nuclear Information System (INIS)

Saleck, Nadja; Bremen, Lueder von

2007-01-01

Smoothing of wind power forecast errors is well-known for large areas. Comparable effects within a wind farm are investigated in this paper. A Neural Network was taken to predict the power output of a wind farm in north-western Germany comprising 17 turbines. A comparison was done between an algorithm that fits mean wind and mean power data of the wind farm and a second algorithm that fits wind and power data individually for each turbine. The evaluation of root mean square errors (RMSE) shows that relative small smoothing effects occur. However, it can be shown for this wind farm that individual calculations have the advantage that only a few turbines are needed to give better results than the use of mean data. Furthermore different results occurred if predicted wind speeds are directly fitted to observed wind power or if predicted wind speeds are first fitted to observed wind speeds and then applied to a power curve. The first approach gives slightly better RMSE values, the bias improves considerably

Wind Power Today: 1998 Wind Energy Program Highlights

Energy Technology Data Exchange (ETDEWEB)

Tromly, K.

1999-06-17

The US Department of Energy's Office of Energy Efficiency and Renewable Energy manages the Federal Wind Energy Program. The mission of the program is to help the US wind industry to complete the research, testing, and field verification needed to fully develop advanced wind technologies that will lead the world in cost-effectiveness and reliability. This publication, printed annually, provides a summary of significant achievements in wind energy made during the previous calendar year. Articles include wind energy in the Midwest, an Alaskan wind energy project, the US certification program, structural testing, and the federal program in review.

Wind energy: Overcoming inadequate wind and modeling uncertainties

Energy Technology Data Exchange (ETDEWEB)

Kane, Vivek

2010-09-15

'Green Energy' is the call of the day, and significance of Wind Energy can never be overemphasized. But the key question here is - What if the wind resources are inadequate? Studies reveal that the probability of finding favorable wind at a given place on land is only 15%. Moreover, there are inherent uncertainties associated with wind business. Can we overcome inadequate wind resources? Can we scientifically quantify uncertainty and model it to make business sense? This paper proposes a solution, by way of break-through Wind Technologies, combined with advanced tools for Financial Modeling, enabling vital business decisions.

Operation Design of Wind Turbines in Strong Wind Conditions

DEFF Research Database (Denmark)

Shen, Wen Zhong; Montes, Melissa Barroso; Odgaard, Peter Fogh

2012-01-01

and variable speed pitch regulated wind turbines. The variable speed design is more suitable for wind turbines to run at very high wind speeds which can help the turbine braking system to stop the turbine at the new "cut-out" wind speed. Reference power, rotational speed and pitch angle have been designed...... optimally. In order to reduce the possible increased loading, fatigue due to the wind gusts, control strategies have been considered for both constant sped and variable speed pitch regulated wind turbines. The control study shows that the designed controllers can reduce the standard deviations efficiently......In order to reduce the impact on the electrical grid from the shutdown of MW wind turbines at wind speeds higher than the cut-out wind speed of 25 m/s, we propose in this paper to run the turbines at high wind speeds up to 40 m/s. Two different operation designs are made for both constant speed...

Endurance Wind Power : practical insights into small wind

International Nuclear Information System (INIS)

Hicks, D.

2008-01-01

This presentation discussed practical issues related to purchasing and installing small wind turbines in Canada. Wind power capacity can be estimated by looking at provincial wind maps as well as by seeking wind data at local airports. Wind resources are typically measured at heights of between 20 meters and 50 m. The height of a wind turbine tower can significantly increase the turbine's wind generating capacity. Turbine rotors should always be placed 30 feet higher than obstacles within 500 feet. Many provinces have now mandated utilities to accept renewable energy resources from grid-connected wind energy plants. Net billing systems are used to determine the billing relationship between power-producing consumers and the utilities who will buy the excess power and sell it to other consumers. Utilities are not yet mandated to purchase excess power, and it is likely that federal and provincial legislation will be needed to ensure that net billing systems continue to grow. Many Canadian municipalities have no ordinances related to wind turbine placements. Consumers interested in purchasing small wind turbines should ensure that the turbine has been certified by an accredited test facility and has an adequate safety system. The noise of the turbine as well as its power performance in relation to the purchaser's needs must also be considered. It was concluded that small wind turbines can provide a means for electricity consumers to reduce their carbon footprint and hedge against the inflationary costs of fossil-fuelled energy resources. tabs., figs

Operation and control of large wind turbines and wind farms

Energy Technology Data Exchange (ETDEWEB)

Soerensen, Poul; Hansen, Anca D.; Thomsen, Kenneth (and others)

2005-09-01

This report is the final report of a Danish research project 'Operation and control of large wind turbines and wind farms'. The objective of the project has been to analyse and assess operational strategies and possibilities for control of different types of wind turbines and different wind farm concepts. The potentials of optimising the lifetime/energy production ratio by means of using revised operational strategies for the individual wind turbines are investigated. Different strategies have been simulated, where the power production is decreased to an optimum when taking loads and actual price of produced electricity into account. Dynamic models and control strategies for the wind farms have also been developed, with the aim to optimise the operation of the wind farms considering participation in power system control of power (frequency) and reactive power (voltage), maximise power production, keep good power quality and limit mechanical loads and life time consumption. The project developed models for 3 different concepts for wind farms. Two of the concepts use active stall controlled wind turbines, one with AC connection and one with modern HVDC/VSC connection of the wind farm. The third concept is based on pitch controlled wind turbines using doubly fed induction generators. The models were applied to simulate the behaviour of the wind farm control when they were connected to a strong grid, and some initial simulations were performed to study the behaviour of the wind farms when it was isolated from the main grid on a local grid. Also the possibility to use the available information from the wind turbine controllers to predict the wind speed has been investigated. The main idea has been to predict the wind speed at a wind turbine using up-wind measurements of the wind speed in another wind turbine. (au)

VisibleWind: wind profile measurements at low altitude

Science.gov (United States)

Wilkerson, Tom; Bradford, Bill; Marchant, Alan; Apedaile, Tom; Wright, Cordell

2009-09-01

VisibleWindTM is developing an inexpensive rapid response system, for accurately characterizing wind shear and small scale wind phenomena in the boundary layer and for prospecting suitable locations for wind power turbines. The ValidWind system can also collect reliable "ground truth" for other remote wind sensors. The system employs small (0.25 m dia.) lightweight balloons and a tracker consisting of an Impulse 200 XL laser rangefinder coupled to a PC for automated data recording. Experiments on balloon trajectories demonstrate that the laser detection of range (+/- 0.5 m), together with measured azimuth and altitude, is an inexpensive, convenient, and capable alternative to other wind tracking methods. The maximum detection range has been increased to 2200 meters using micro-corner-cube retroreflector tape on balloons. Low power LEDs enable nighttime tracking. To avoid large balloon gyrations about the mean trajectory, we use balloons having low ascent rates and subcritical Reynolds numbers. Trajectory points are typically recorded every 4 - 7 seconds. Atmospheric features observed under conditions of inversions or "light and variable winds" include abrupt onsets of shear at altitudes of 100-250 m, velocity changes of order 1-3 m/s within layers of 10-20 m thickness, and veering of the wind direction by 180 degrees or more as altitude increases from 300 to 500 m. We have previously reported comparisons of balloon-based wind profiles with the output of a co-located sodar. Even with the Impulse rangefinder, our system still requires a "man in the loop" to track the balloon. A future system enhancement will automate balloon tracking, so that laser returns are obtained automatically at 1 Hz. While balloon measurements of large-scale, high altitude wind profiles are well known, this novel measurement system provides high-resolution, real-time characterization of the fluctuating local wind fields at the bottom of the boundary layer where wind power turbines and other

Amadurecimento de filtros lentos de areia e remoção de microrganismos indicadores de qualidade da água ao longo da profundidade do leito: uma avaliação em instalação piloto Maturation of slow sand filters and removal of microorganisms' indicators of water quality along the media depth: an evaluation in pilot plant

Directory of Open Access Journals (Sweden)

Ludmila Ladeira Alves de Brito

2005-12-01

Full Text Available O potencial da filtração lenta como opção tecnológica para o tratamento de água nos países em desenvolvimento e sua capacidade de remoção de contaminantes, sobretudo patogênicos, são reconhecidos. Contudo, ainda permanece incompleto o conhecimento acerca dos mecanismos que predominantemente atuam na remoção dos microrganismos. Objetivando avançar nessa compreensão, desenvolveu-se uma investigação experimental, em unidades piloto, em filtros lentos de areia com escoamento descendente e ascendente, operados com água sintética e duas taxas de filtração (3 e 6m³/m2.d. A retenção dos microrganismos indicadores foi avaliada em cinco camadas, com 0,15 m de espessura cada, em dois momentos da carreira. A maturidade biológica do leito filtrante foi menos favorecida pela taxa mais alta de filtração e pelo fluxo ascendente. Os 0,45 m iniciais do leito filtrante foram importantes na remoção de microrganismos sob as condições estudadas, mas a remoção não se restringiu a estas camadas, tendo sido observada para todos os indicadores retenção nas camadas de 0,45-0,60 m e de 0,60-0,75 m. A schmutzdecke parece desempenhar papel efetivo na remoção de indicadores microbiológicos apenas quando bem desenvolvida. Há uma indicação de que a camada suporte exerce algum papel na retenção de sólidos e microrganismos no fluxo ascendente.The potential of the slow sand filtration as technological option for drinking-water treatment in developing countries and its capacity of contaminants removal, mainly pathogens, are recognized.However, the knowledge concerning the predominant mechanisms that act in microorganism's removal still remains incomplete. Aiming to advance in the understanding of these themes, an experimental investigation was carried out, working with pilot plants of downflow and upflow slow sand filters, operated with synthetic water and two filtration rates (3 and 6 m³/m².d. The microorganisms indicators removal was

Satellite information for wind energy applications

Energy Technology Data Exchange (ETDEWEB)

Nielsen, M.; Astrup, P.; Bay Hasager, C.

2004-11-01

are obtained 3 to 8 times monthly. The relatively low number of samples and the absolute uncertainty within the maps, {approx} 1.3 ms-1, offer wind resource statistics useful only in pre-feasibility studies or in combination with classical offshore observations. (au)

Wind Power Meteorology

DEFF Research Database (Denmark)

Lundtang Petersen, Erik; Mortensen, Niels Gylling; Landberg, Lars

Wind power meteorology has evolved as an applied science, firmly founded on boundary-layer meteorology, but with strong links to climatology and geography. It concerns itself with three main areas: siting of wind turbines, regional wind resource assessment, and short-term prediction of the wind...... resource. The history, status and perspectives of wind power meteorology are presented, with emphasis on physical considerations and on its practical application. Following a global view of the wind resource, the elements of boundary layer meteorology which are most important for wind energy are reviewed......: wind profiles and shear, turbulence and gust, and extreme winds. The data used in wind power meteorology stem mainly from three sources: onsite wind measurements, the synoptic networks, and the re-analysis projects. Wind climate analysis, wind resource estimation and siting further require a detailed...

Remote Sensing Wind and Wind Shear System.

Science.gov (United States)

Contents: Remote sensing of wind shear and the theory and development of acoustic doppler; Wind studies; A comparison of methods for the remote detection of winds in the airport environment; Acoustic doppler system development; System calibration; Airport operational tests.

Wind for Schools: A Wind Powering America Project

Science.gov (United States)

US Department of Energy, 2007

2007-01-01

The U.S. Department of Energy's (DOE's) Wind Powering America program (based at the National Renewable Energy Laboratory) sponsors the Wind for Schools Project to raise awareness in rural America about the benefits of wind energy while simultaneously educating college seniors regarding wind energy applications. The three primary project goals of…

Energy-Aware Path Planning for UAS Persistent Sampling and Surveillance

Science.gov (United States)

Shaw-Cortez, Wenceslao

The focus of this work is to develop an energy-aware path planning algorithm that maximizes UAS endurance, while performing sampling and surveillance missions in a known, stationary wind environment. The energy-aware aspect is specifically tailored to extract energy from the wind to reduce thrust use, thereby increasing aircraft endurance. Wind energy extraction is performed by static soaring and dynamic soaring. Static soaring involves using upward wind currents to increase altitude and potential energy. Dynamic soaring involves taking advantage of wind gradients to exchange potential and kinetic energy. The path planning algorithm developed in this work uses optimization to combine these soaring trajectories with the overarching sampling and surveillance mission. The path planning algorithm uses a simplified aircraft model to tractably optimize soaring trajectories. This aircraft model is presented and along with the derivation of the equations of motion. A nonlinear program is used to create the soaring trajectories based on a given optimization problem. This optimization problem is defined using a heuristic decision tree, which defines appropriate problems given a sampling and surveillance mission and a wind model. Simulations are performed to assess the path planning algorithm. The results are used to identify properties of soaring trajectories as well as to determine what wind conditions support minimal thrust soaring. Additional results show how the path planning algorithm can be tuned between maximizing aircraft endurance and performing the sampling and surveillance mission. A means of trajectory stitching is demonstrated to show how the periodic soaring segments can be combined together to provide a full solution to an infinite/long horizon problem.

2008 WIND TECHNOLOGIES MARKET REPORT

Energy Technology Data Exchange (ETDEWEB)

Wiser, Ryan H.; Bolinger, Mark; Barbose, G.; Mills, A.; Rosa, A.; Porter, K.; Fink, S.; Tegen, S.; Musial, W.; Oteri, F.; Heimiller, D.; Rberts, B.; Belyeu, K.; Stimmel, R.

2009-07-15

domestic wind power market, including federal and state policy drivers, transmission issues, and grid integration. Finally, the report concludes with a preview of possible near- to medium-term market developments. This version of the Annual Report updates data presented in the previous editions, while highlighting key trends and important new developments from 2008. New to this edition is an executive summary of the report and an expanded final section on near- to medium-term market development. The report concentrates on larger-scale wind applications, defined here as individual turbines or projects that exceed 50 kW in size. The U.S. wind power sector is multifaceted, however, and also includes smaller, customer-sited wind turbines used to power the needs of residences, farms, and businesses. Data on these applications are not the focus of this report, though a brief discussion on Distributed Wind Power is provided on page 4. Much of the data included in this report were compiled by Berkeley Lab, and come from a variety of sources, including the American Wind Energy Association (AWEA), the Energy Information Administration (EIA), and the Federal Energy Regulatory Commission (FERC). The Appendix provides a summary of the many data sources used in the report. Data on 2008 wind capacity additions in the United States are based on information provided by AWEA; some minor adjustments to those data may be expected. In other cases, the data shown here represent only a sample of actual wind projects installed in the United States; furthermore, the data vary in quality. As such, emphasis should be placed on overall trends, rather than on individual data points. Finally, each section of this document focuses on historical market information, with an emphasis on 2008; with the exception of the final section, the report does not seek to forecast future trends.

Liberdade de expressão na web: análise de decisões judiciais sobre a remoção de conteúdo em sites

Directory of Open Access Journals (Sweden)

Letícia Bodanese Rodegheri

2013-12-01

Full Text Available A Internet surge como um meio dinâmico e apto a potencializar a efetivação do direito fundamental à liberdade de expressão, informação e opinião, na medida em que é permitido ao próprio cibernauta emitir, transmitir e compartilhar informações, sem a necessidade de imposição de filtros ou de censura prévia. O artigo, utilizando-se dos métodos bibliográfico e documental, objetiva, ao analisar decisões judiciais, verificar como o Poder Judiciário está se manifestando frente aos inúmeros pedidos de remoção de conteúdo em sites. Conclui-se que os magistrados estão atentos às características definidoras da Internet e, ao sopesar os direitos fundamentais em conflito, está-se dando primazia à liberdade de expressão.

Estimation of Typhoon Wind Hazard Curves for Nuclear Sites

Energy Technology Data Exchange (ETDEWEB)

Choun, Young-Sun; Kim, Min-Kyu [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

The intensity of such typhoons, which can influence the Korean Peninsula, is on an increasing trend owing to a rapid change of climate of the Northwest Pacific Ocean. Therefore, nuclear facilities should be prepared against future super-typhoons. Currently, the U.S. Nuclear Regulatory Commission requires that a new NPP should be designed to endure the design-basis hurricane wind speeds corresponding to an annual exceedance frequency of 10{sup -7} (return period of 10 million years). A typical technique used to estimate typhoon wind speeds is based on a sampling of the key parameters of typhoon wind models from the distribution functions fitting statistical distributions to the observation data. Thus, the estimated wind speeds for long return periods include an unavoidable uncertainty owing to a limited observation. This study estimates the typhoon wind speeds for nuclear sites using a Monte Carlo simulation, and derives wind hazard curves using a logic-tree framework to reduce the epistemic uncertainty. Typhoon wind speeds were estimated for different return periods through a Monte-Carlo simulation using the typhoon observation data, and the wind hazard curves were derived using a logic-tree framework for three nuclear sites. The hazard curves for the simulated and probable maximum winds were obtained. The mean hazard curves for the simulated and probable maximum winds can be used for the design and risk assessment of an NPP.

A Study of Nonstationary Wind Effects on a Full-Scale Large Cooling Tower Using Empirical Mode Decomposition

Directory of Open Access Journals (Sweden)

X. X. Cheng

2017-01-01

Full Text Available Wind effects on structures obtained by field measurements are often found to be nonstationary, but related researches shared by the wind-engineering community are still limited. In this paper, empirical mode decomposition (EMD is applied to the nonstationary wind pressure time-history samples measured on an actual 167-meter high large cooling tower. It is found that the residue and some intrinsic mode functions (IMFs of low frequencies produced by EMD are responsible for the samples’ nonstationarity. Replacing the residue by the constant mean and subtracting the IMFs of low frequencies can help the nonstationary samples become stationary ones. A further step is taken to compare the loading characteristics extracted from the original nonstationary samples with those extracted from the processed stationary samples. Results indicate that nonstationarity effects on wind loads are notable in most cases. The passive wind tunnel simulation technique based on the assumption of stationarity is also examined, and it is found that the technique is basically conservative for use.

Offshore wind resource estimation for wind energy

DEFF Research Database (Denmark)

Hasager, Charlotte Bay; Badger, Merete; Mouche, A.

2010-01-01

Satellite remote sensing from active and passive microwave instruments is used to estimate the offshore wind resource in the Northern European Seas in the EU-Norsewind project. The satellite data include 8 years of Envisat ASAR, 10 years of QuikSCAT, and 23 years of SSM/I. The satellite observati......Satellite remote sensing from active and passive microwave instruments is used to estimate the offshore wind resource in the Northern European Seas in the EU-Norsewind project. The satellite data include 8 years of Envisat ASAR, 10 years of QuikSCAT, and 23 years of SSM/I. The satellite...... observations are compared to selected offshore meteorological masts in the Baltic Sea and North Sea. The overall aim of the Norsewind project is a state-of-the-art wind atlas at 100 m height. The satellite winds are all valid at 10 m above sea level. Extrapolation to higher heights is a challenge. Mesoscale...... modeling of the winds at hub height will be compared to data from wind lidars observing at 100 m above sea level. Plans are also to compare mesoscale model results and satellite-based estimates of the offshore wind resource....

Bats and wind turbines : pre-siting and pre-construction survey protocols

Energy Technology Data Exchange (ETDEWEB)

Lausen, C.; Baerwald, E.; Gruver, J.; Barclay, R. [Calgary Univ., AB (Canada)

2008-05-15

Studies have shown that a number of bats are killed by moving wind turbine blades at wind farms throughout North America. The studies have shown that over 80 per cent of the fatalities involve migratory bat species. Hoary bats, eastern red bats, and silver-haired bats dominate the fatalities during the fall migration period. Fatality rates vary among wind energy developments. Some data suggest that fatalities are higher on nights with lower wind speeds, and increased fatalities have been associated with taller wind turbines. This report outlined pre-construction survey requirements for preventing bat fatalities at wind power plants. A pre-construction survey was recommended to achieve a representative sampling of bat activity and determine the relative risk to bats. The study suggested that monitoring data from locations across the province should be pooled to provide a better understanding of the landscape-scale patterns of bat migration. Monitoring for bats should be conducted continuously due to the sporadic nature of peaks in bat activity, the influence of temperature, moon phase, and weather variables. Sampling techniques for acoustic detection, radar tracking, and mist-netting should be implemented to determine the abundance of susceptible species and the location of migration routes. All existing meteorological towers should be used as sampling stations with bat detectors installed at ground level and near the top of the tower. Additional detector stations should be distributed throughout the wind resource area. Specialized anabat microphones should be calibrated to record bat activity. Acoustic data should be presented as total bat passes and mean passes per night and matched with corresponding meteorological data. It was concluded that pre-construction monitoring data should be gathered and made available for collaborative and cumulative research efforts. 28 refs., 1 fig.

Wind Observatory 2017. Analysis of the wind power market, wind jobs and future of the wind industry in France

International Nuclear Information System (INIS)

2017-09-01

Two years after the enactment of the Energy Transition for Green Growth Act, wind power capacity continues to grow in France, exceeding 12 GWatt the end of 2016 and soon to account for 5% of France's electric power consumption. This vitality, which is set to continue in 2017, will help France achieve its objectives of an installed capacity of 15,000 MW in onshore wind by 2018 and 21,800 to 26,000 MW by 2023. The current pace will nevertheless have to be accelerated in order to reach the realistic objective of 26 GW by 2023 mentioned in the multi-annual energy plan (PPE). With 1,400 jobs created in one year and more than 3,300 over the last two years, the relevance of wind power as a driving force of sustainable job creation throughout the country is unequivocally confirmed: the increase in wind power capacity continues to contribute to the growth in employment in the country. Prepared in collaboration with the consulting firm BearingPoint, the 2017 edition of the Observatory aims to give the reader an overview of employment in the wind industry and the wind power market over the period under consideration. Any changes from the three previous editions are highlighted. It is based on a comprehensive census of all market participants on three themes: employment, the market and the future of wind power. The Observatory gives an accurate picture of how the wind energy industry is structured, thereby presenting a precise overview of the wind energy industry and all its components

Lake Michigan Wind Assessment Analysis, 2012 and 2013

Directory of Open Access Journals (Sweden)

Charles R Standridge

2017-03-01

Full Text Available A study was conducted to address the wind energy potential over Lake Michigan to support a commercial wind farm.  Lake Michigan is an inland sea in the upper mid-western United States.  A laser wind sensor mounted on a floating platform was located at the mid-lake plateau in 2012 and about 10.5 kilometers from the eastern shoreline near Muskegon Michigan in 2013.  Range gate heights for the laser wind sensor were centered at 75, 90, 105, 125, 150, and 175 meters.  Wind speed and direction were measured once each second and aggregated into 10 minute averages.  The two sample t-test and the paired-t method were used to perform the analysis.  Average wind speed stopped increasing between 105 m and 150 m depending on location.  Thus, the collected data is inconsistent with the idea that average wind speed increases with height. This result implies that measuring wind speed at wind turbine hub height is essential as opposed to using the wind energy power law to project the wind speed from lower heights.  Average speed at the mid-lake plateau is no more that 10% greater than at the location near Muskegon.  Thus, it may be possible to harvest much of the available wind energy at a lower height and closer to the shoreline than previously thought.  At both locations, the predominate wind direction is from the south-southwest.  The ability of the laser wind sensor to measure wind speed appears to be affected by a lack of particulate matter at greater heights.   Keywords: wind assessment, Lake Michigan, LIDAR wind sensor, statistical analysis. Article History: Received June 15th 2016; Received in revised form January 16th 2017; Accepted February 2nd 2017 Available online How to Cite This Article: Standridge, C., Zeitler, D., Clark, A., Spoelma, T., Nordman, E., Boezaart, T.A., Edmonson, J.,  Howe, G., Meadows, G., Cotel, A. and Marsik, F. (2017 Lake Michigan Wind Assessment Analysis, 2012 and 2013. Int. Journal of Renewable Energy Development

Integrated spatial assessment of wind erosion risk in Hungary

Directory of Open Access Journals (Sweden)

L. Pásztor

2016-11-01

Full Text Available Wind erosion susceptibility of Hungarian soils was mapped on the national level integrating three factors of the complex phenomenon of deflation (physical soil features, wind characteristics, and land use and land cover. Results of wind tunnel experiments on erodibility of representative soil samples were used for the parametrization of a countrywide map of soil texture compiled for the upper 5 cm layer of soil, which resulted in a map representing threshold wind velocity exceedance. Average wind velocity was spatially estimated with 0.5′ resolution using the Meteorological Interpolation based on Surface Homogenised Data Basis (MISH method elaborated for the spatial interpolation of surface meteorological elements. The probability of threshold wind velocity exceedance was determined based on values predicted by the soil texture map at the grid locations. Ratio values were further interpolated to a finer 1 ha resolution using sand and silt content of the uppermost (0–5 cm layer of soil as spatial co-variables. Land cover was also taken into account, excluding areas that are not relevant to wind erosion (forests, water bodies, settlements, etc., to spatially assess the risk of wind erosion. According to the resulting map of wind erosion susceptibility, about 10 % of the total area of Hungary can be identified as susceptible to wind erosion. The map gives more detailed insight into the spatial distribution of wind-affected areas in Hungary compared to previous studies.

Inert tracer wind resuspension as a function of wind speed, atmospheric stability, and initial tracer particle size

International Nuclear Information System (INIS)

Sehmel, G.A.; Lloyd, F.D.

1979-01-01

Wind-caused resuspension rates are being determined in three different, long-term, inert-tracer field experiments. Chemical results were recently received from an accumulated backlog of air filter samples. Resuspension rates are yet to be calculated from these data

Extreme wind estimate for Hornsea wind farm

DEFF Research Database (Denmark)

Larsén, Xiaoli Guo

The purpose of this study is to provide estimation of the 50-year winds of 10 min and 1-s gust value at hub height of 100 m, as well as the design parameter shear exponent for the Hornsea offshore wind farm. The turbulence intensity required for estimating the gust value is estimated using two...... approaches. One is through the measurements from the wind Doppler lidar, WindCube, which implies serious uncertainty, and the other one is through similarity theory for the atmospheric surface layer where the hub height is likely to belong to during strong storms. The turbulence intensity for storm wind...... strength is taken as 0.1. The shear exponents at several heights were calculated from the measurements. The values at 100 m are less than the limit given by IEC standard for all sectors. The 50-year winds have been calculated from various global reanalysis and analysis products as well as mesoscale models...

The social acceptability of wind turbines: some resident are ready to pay to keep their wind turbines. Survey on four French wind farms; L'acceptabilite sociale des eoliennes: des riverains prets a payer pour conserver leurs eoliennes. Enquete sur quatre sites eoliens francais

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-06-15

The authors report a study which aimed at exploiting and deepening the results of a 2001 survey on visual and sound disturbances caused by wind turbines in Sigean (Aude), at identifying all the attitudes and opinions with respect with wind energy, and at assessing the different characteristics of a wind farm (height, localization, and so on). A survey has been performed on four sites located in different French regions. The authors discuss the social-demographic characteristics of the population samples, the global opinion on wind energy, and the opinion of the people on wind turbines located in their neighbourhood. They propose an estimation of benefits and damages related to the vicinity of wind turbines. By applying a method of choice experiments, they reveal the preferences of residents

Evaluation model of wind energy resources and utilization efficiency of wind farm

Science.gov (United States)

Ma, Jie

2018-04-01

Due to the large amount of abandoned winds in wind farms, the establishment of a wind farm evaluation model is particularly important for the future development of wind farms In this essay, consider the wind farm's wind energy situation, Wind Energy Resource Model (WERM) and Wind Energy Utilization Efficiency Model(WEUEM) are established to conduct a comprehensive assessment of the wind farm. Wind Energy Resource Model (WERM) contains average wind speed, average wind power density and turbulence intensity, which assessed wind energy resources together. Based on our model, combined with the actual measurement data of a wind farm, calculate the indicators using the model, and the results are in line with the actual situation. We can plan the future development of the wind farm based on this result. Thus, the proposed establishment approach of wind farm assessment model has application value.

Wind Turbines Adaptation to the Variability of the Wind Field

Science.gov (United States)

Ulianov, Yuriy; Martynenko, Gennadii; Misaylov, Vitaliy; Soliannikova, Iuliia

2010-05-01

WIND TURBINES ADAPTATION TO THE VARIABILITY OF THE WIND FIELD The subject of our scientific research is wind power turbines (WPT) with the horizontal axis which were now common in the world. Efficient wind turbines work is largely determined by non-stationarity of the wind field, expressed in its gustiness, the presence of vertical and horizontal shifts of wind speed and direction. At critical values of the wind parameters WPT has aerodynamic and mechanical overload, leading to breakdowns, premature wear and reduce the life of the wind turbine. To prevent accidents at the peak values of wind speed it is used the regulatory system of windwheels. WPT control systems provide a process orientation of the wind turbine rotor axis in the line of the mean wind. Wind turbines are also equipped with braking device used to protect against breakdowns when a significant increase in the wind. In general, all these methods of regulation are not always effective. Thus, in practice there may be situations when the wind speed is many times greater than the stated limit. For example, if there are microbursts in the atmospheric boundary layer, low-level wind shears caused by its gust front, storms, etc. It is required for a wind power turbine adaptation to intensive short-term wind impulses and considerable vertical wind shifts that the data about them shall be obtained ahead of time. To do this it is necessary to have the information on the real structure of the wind field in the area of the blade sweep for the minimum range against the wind that is determined by the mean speed and the system action time. The implementation of acoustic and laser traditional wind sounding systems is limited by ambient acoustic noise, by heavy rain, snowfall and by fog. There are free of these disadvantages the inclined radioacoustic sounding (IRASS) technique which works for a system of remote detection and control of wind gusts. IRASS technique is realized as low-potential Doppler pulse radar

Economic valuation of the visual externalities of off-shore wind farms

Energy Technology Data Exchange (ETDEWEB)

Ladenburg, J.; Dubgaard, A.; Martensen, L.; Tranberg, J.

2005-07-01

The study is based on a mail survey including 700 households in a national sample, and 350 households in two sub samples in the Horns Rev and Nysted areas. In the choice experiment, four alternative off-shore wind farm distances from the coast were used namely: 8, 12, 18 and 50 km. Based on the respondents' choices between alternative locations of off-shore wind farms their willingness to pay (WTP) for increasing the distance was elicited using three different sub samples for each of the three locations. These sub samples were constructed using the full sample (B-model), a sample containing respondents who were certain in their choice (C-model) and finally a sample containing respondents, who according to a defined set of questions were considered consistent and rational in their choice (R-model). (au)

Investigation of Wind Turbine Rotor Concepts for Offshore Wind Farms

International Nuclear Information System (INIS)

Ceyhan, Özlem; Grasso, Francesco

2014-01-01

Current plans in offshore wind energy developments call for further reduction of cost of energy. In order to contribute to this goal, several wind turbine rotor concepts have been investigated. Assuming the future offshore wind turbines will operate only in the offshore wind farms, the rotor concepts are not only evaluated for their stand-alone performances and their potential in reducing the loads, but also for their performance in an offshore wind farm. In order to do that, the 10MW reference wind turbine designed in Innwind.EU project is chosen as baseline. Several rotor parameters have been modified and their influences are investigated for offshore wind turbine design purposes. This investigation is carried out as a conceptual parametrical study. All concepts are evaluated numerically with BOT (Blade optimisation tool) software in wind turbine level and with Farmflow software in wind farm level for two wind farm layouts. At the end, all these concepts are compared with each other in terms of their advantages and disadvantages

LIDAR wind speed measurements from a rotating spinner (SpinnerEx 2009)

DEFF Research Database (Denmark)

Angelou, Nikolas; Mikkelsen, Torben; Hansen, Kasper Hjorth

spinner of a MW-sized wind turbine, and investigate the approaching wind fields from this vantage point. Time series of wind speed measurements from the lidar with 50 Hz sampling rate were successfully obtained for approximately 60 days, during the measurement campaign lasting from April to August 2009....... In this report, information is given regarding the experimental setup and the lidar’s operation parameters. The geometrical model used for the reconstruction of the scanning pattern of the lidar is described. This model takes into account the lidar’s pointing direction, the spinner axis’s vertical tilt...... and the wind turbine’s yaw relative to the mean wind speed direction. The data analysis processes are documented. A methodology for the calculation of the yaw misalignment of the wind turbine relative to the wind direction, as a function of various averaging times, is proposed, using the lidar’s instantaneous...

Mixture distributions of wind speed in the UAE

Science.gov (United States)

Shin, J.; Ouarda, T.; Lee, T. S.

2013-12-01

sample wind data, the adjusted coefficient of determination, Bayesian Information Criterion (BIC) and Chi-squared statistics were computed. Results indicate that MHML presents the best performance of parameter estimation for the used mixture distributions. In most of the employed 7 stations, mixture distributions give the best fit. When the wind speed regime shows mixture distributional characteristics, most of these regimes present the kurtotic statistical characteristic. Particularly, applications of mixture distributions for these stations show a significant improvement in explaining the whole wind speed regime. In addition, the Weibull-Weibull mixture distribution presents the best fit for the wind speed data in the UAE.

Wind of opportunity

International Nuclear Information System (INIS)

Jamieson, Peter

1999-01-01

This article traces the move towards the offshore exploitation of wind energy in Europe, and presents information on existing offshore wind energy projects and proposed wind turbine prototypes for offshore operation. The building of the first major offshore wind project at Vindeby, the use of rock socketed monopile foundations for pile drilling and erection of the wind turbines from a mobile jack-up barge, the costs of wind turbines, the fatigue loads on the support structures due to the wind loading, and the offshore wind market in the UK and Europe are discussed. (UK)

Wind Atlas of Bay of Bengal with Satellite Wind Measurement

DEFF Research Database (Denmark)

Nadi, Navila Rahman

footstep towards offshore wind energy analysis for this region. Generally, it is difficult to find offshore wind data relative to the wind turbine hub heights, therefore a starting point is necessary to identify the possible wind power density of the region. In such scenario, Synthetic aperture radars (SAR......The objective of this study is to obtain appropriate offshore location in the Bay of Bengal, Bangladesh for further development of wind energy. Through analyzing the previous published works, no offshore wind energy estimation has been found here. That is why, this study can be claimed as the first......) have proven useful. In this study, SAR based dataset- ENVISAT ASAR has been used for Wind Atlas generation. Furthermore, a comparative study has been performed with Global Wind Atlas (GWA) to determine a potential offshore wind farm. Additionally, the annual energy production of that offshore windfarm...

Design winds during ice storm as a function of direction for transmission lines

Energy Technology Data Exchange (ETDEWEB)

Chouinard, L. [McGill Univ., Montreal, PQ (Canada); Feknous, N. [SNC-Lavalin, Montreal, PQ (Canada); Sabourin, G. [Hydro-Quebec, Montreal, PQ (Canada)

2005-07-01

The effects of wind directionality are important considerations in the design of electric transmission lines. A procedure for the estimation of the probability distribution function of maximum wind speed as a function of direction was proposed. The procedure was applied to the sample of annual maximum wind speeds using the Gumbal distribution method and then used to estimate the maximum wind speed as a function of direction for the sample of maximum annual wind speeds, and maximum annual wind speeds during ice storms at 22 locations throughout Quebec. Wind direction obtained from the meteorological stations was recorded in 10 degrees sectors. The data set was used to obtain maximum wind speed for each year in each of 36 sectors. The joint probability distribution function was obtained by assuming that extreme distribution for non-directional winds was common to all directions during a season or period, as well as by assuming independence between wind speed and wind direction during a storm pattern. Structural effects were obtained by integrating the joint probability distribution with design equations. Results were then presented in the form of a ratio relative to the reference wind speed for each location. The procedure was demonstrated using a meteorological data set as well as glaze ice data from Quebec City, and covered a period of 30 years. Results indicated that a reduction factor of 25 per cent can be achieved on ice accumulations when overhead lines are directed parallel to dominant winds. It was concluded that the method will represent significant savings in the design and up-grading of existing lines. Further research will be conducted to address issues related to regional criteria and local adjustments for topographical features. 7 refs., 4 figs.

Aquatic carbon export from peatland catchments recently undergone wind farm development

Science.gov (United States)

Smith, Ben; Waldron, Susan; Henderson, Andrew; Flowers, Hugh; Gilvear, David

2013-04-01

Scotland's peat landscapes are desirable locations for wind-based renewables due to high wind resources and low land use pressures in these areas. The environmental impact of sitting wind-based renewables on peats however, is unknown. Globally, peatlands are important terrestrial carbon stores. Given the topical nature of carbon-related issues, e.g. global warming and carbon footprints, it is imperative we help mitigate their degradation and maintain carbon sequestration. To do so, we need to better understand how peatland systems function with regards to their carbon balance (export versus sequestration) so we can assess their resilience and adaptation to hosting land-based renewable energy projects. Predicting carbon lost as a result of construction of wind farms built on peatland has not been fully characterised and this research will provide data that can supplement current 'carbon payback calculator' models for wind farms that aim to reinforce their 'green' credentials. Transfer of carbon from the terrestrial peatland systems to the aquatic freshwater and oceanic systems is most predominant during periods of high rainfall. It has been estimated that 50% of carbon is exported during only 10% of highest river flows, (Hinton et al., 1998). Furthermore, carbon export from peatlands is known to have a seasonal aspect with highest concentrations of dissolved organic carbon (DOC) found mostly in late summer months of August and September and lowest in December and January, (Dawson et al., 2004). Event sampling, where high intensity sample collection is carried out during high river flow periods, offers a better insight, understanding and estimation of carbon aquatic fluxes from peatland landscapes. The Gordonbush estate, near Brora, has an extensive peatland area where a wind farm development has recently been completed (April 2012). Investigations of aquatic carbon fluxes from this peatland system were started in July 2010, in conjunction with the start of

Comportamento diário ao longo do período de alimentação do primeiro estágio do sistema francês de wetland vertical, em termos de remoção de matéria orgânica e amônia

Directory of Open Access Journals (Sweden)

Camila Maria Trein

2018-01-01

Full Text Available O objetivo desse trabalho foi avaliar o comportamento do potencial de nitrificação e remoção de matéria orgânica no primeiro estágio de um wetland construído vertical - sistema francês (WCV-SF, operando com dois leitos em paralelo, cada um com 7 dias de alimentação e 7 dias de repouso, sob condições climáticas brasileiras. A estação de tratamento avaliada está localizada no Centro de Pesquisa e Treinamento em Saneamento (CePTS da Universidade Federal de Minas Gerais e Companhia de Saneamento de Minas Gerais, UFMG/COPASA, na cidade de Belo Horizonte, Brasil. Complementando o monitoramento rotineiro praticado há anos neste sistema, efetuou-se um monitoramento intensivo da qualidade do afluente e do efluente do WCV-SF durante uma semana, por meio de análises físico-químicas, através de coletas simples diárias nos tempos de 5, 10, 15, 20, 30, 40 e 50 minutos depois do início de uma batelada. Durante o período de monitoramento foi possível observar a eficiência dessa etapa associada à decomposição da matéria orgânica, permanecendo satisfatória mesmo em períodos de sobrecarga. Com concentrações positivas de oxigênio no efluente, o desempenho do sistema ao longo dos 7 dias de alimentação apresentou eficiência média de remoção e 69% para DQO. Em termos de nitrogênio, a eficiência de remoção de N-NH4+ foi de 58% e a produção de N-NO3- diminuiu com o avanço dos dias de alimentação, reportando 20 mg L-1 no 2º dia e 11 mg L-1 no último. De uma forma geral, apesar de ter apenas duas unidades em paralelo, o sistema mostrou boa capacidade de receber esgoto bruto por um período de tempo maior de alimentação, reforçando os resultados obtidos no monitoramento rotineiro.

Eficácia da irrigação ultrassônica passiva na remoção de hidróxido de cálcio

Directory of Open Access Journals (Sweden)

Priscila Tahani Michelsen Zart

Full Text Available INTRODUÇÃO: Remanescentes de Hidróxido de Cálcio [Ca(OH2] podem interferir na qualidade da obturação endodôntica. OBJETIVO : Avaliar a eficácia da Irrigação Ultrassônica Passiva (IUP associada à técnica convencional na remoção de medicação intracanal à base de Ca(OH2. METODOLOGIA: Trinta dentes humanos anteriores monorradiculares foram usados. Os canais radiculares foram preparados com instrumentos manuais tipo K e preenchidos com medicação intracanal à base de Ca(OH2, contendo PMCC e propilenoglicol. Após sete dias, a pasta de Ca(OH2 foi removida de todos os canais radiculares com um instrumento manual e irrigação de NaOCl 1% com seringa. Os espécimes foram randomizados em dois grupos (n=12 de acordo com a irrigação final: Irrigação Manual - agitação manual de EDTA 17 % e irrigação de NaOCl 1%; IUP - agitação ultrassônica de NaOCl 1% (três ativações de 20s seguida da ativação de EDTA 17% por 1 min. O Grupo Controle (n=6 não recebeu medicação intracanal. Todos os espécimes foram clivados e a quantidade de Ca(OH2 remanescente foi calculada com o auxílio do estereomicroscrópio (20×. Os testes Kruskall-Wallis e Wilcoxon foram utilizados para avaliar a porcentagem de Ca(OH2 remanescente. RESULTADO: O grupo da IUP apresentou, estatisticamente, as menores porcentagens de Ca(OH2 remanescente, quando comparado ao grupo da Irrigação Manual, independentemente dos terços analisados (P < 0,05. O terço apical apresentou a maior quantidade de medicação residual, em ambos os grupos (P < 0,05. CONCLUSÃO : A associação da IUP com a técnica convencional demonstrou ser mais eficiente na remoção de medicação intracanal à base de Ca(OH2 do que a combinação da Irrigação Manual com a técnica convencional.

Estudo da estabilidade química da magnetita utilizada como adsorvedor na remoção de compostos orgânicos de soluções

Directory of Open Access Journals (Sweden)

Ortiz N.

2003-01-01

Full Text Available Um resíduo siderúrgico composto predominantemente por magnetita (Fe3O4 finamente dividida foi empregado como material adsorvedor não convencional na adsorção e fixação de compostos corantes orgânicos tóxicos. Estudos preliminares indicaram que a magnetita quando utilizada em meio ácido (pH<3 sob agitação contínua pode apresentar diversos graus de desagregação e de solubilização. Este efeito é indesejável em sistemas adsortivos porque representa redução na porcentagem de remoção de composto tóxico orgânico e possível aumento de contaminação por produtos de dissolução e de desagregação da magnetita. Soluções de metasilicato de sódio, sulfato de ferro e hidróxido de sódio foram empregadas nos processos de estabilização de quatro frações granulométricas da magnetita usadas como adsorvedor não convencional em meio ácido. Os resultados obtidos permitiram concluir que o tratamento com metasilicato de sódio das frações de magnetita resulta em redução de 1% nos valores de remoção de composto tóxico corante da solução (de 98% para a fração sem tratamento para 97% para a fração com tratamento com metasilicato e redução nos valores de constante de velocidade de adsorção (k ab de 30.10-3 mg.g-1.min-1 para 10.10-3 mg.g-1.min-1. Embora tenha sido observada redução na capacidade adsortiva das frações tratadas e na velocidade de adsorção, este efeito foi considerado aceitável comparando-se o aumento da estabilidade química e redução nos valores de perda de massa em 46%. Analisando-se as isotermas obtidas para as frações #30 com e sem tratamento, pode-se confirmar que o tratamento com metasilicato promoveu um processo de adsorção mais favorável, com menor interferência dos processos de dissolução, de desagregação e maior correspondência com o modelo de Freundlich.

Dynamic influences of wind power on the power system

Energy Technology Data Exchange (ETDEWEB)

Rosas, Pedro

2003-03-01

The thesis first presents the basics influences of wind power on the power system stability and quality by pointing out the main power quality issues of wind power in a small-scale case and following, the expected large-scale problems are introduced. Secondly, a dynamic wind turbine model that supports power quality assessment of wind turbines is presented. Thirdly, an aggregate wind farm model that support power quality and stability analysis from large wind farms is presented. The aggregate wind farm model includes the smoothing of the relative power fluctuation from a wind farm compared to a single wind turbine. Finally, applications of the aggregate wind farm model to the power systems are presented. The power quality and stability characteristics influenced by large-scale wind power are illustrated with three cases. In this thesis, special emphasis has been given to appropriate models to represent the wind acting on wind farms. The wind speed model to a single wind turbine includes turbulence and tower shadow effects from the wind and the rotational sampling turbulence due to the rotation of the blades. In a park scale, the wind speed model to the wind farm includes the spatial coherence between different wind turbines. Here the wind speed model is applied to a constant rotational speed wind turbine/farm, but the model is suitable to variable speed wind turbine/farm as well. The cases presented here illustrate the influences of the wind power on the power system quality and stability. The flicker and frequency deviations are the main power quality parameters presented. The power system stability concentrates on the voltage stability and on the power system oscillations. From the cases studied, voltage and the frequency variations were smaller than expected from the large-scale wind power integration due to the low spatial correlation of the wind speed. The voltage quality analysed in a Brazilian power system and in the Nordel power system from connecting large

Transmission Line Series Compensation for Wind Energy Transmission

International Nuclear Information System (INIS)

Palanichamy, C; Wong, Y C

2015-01-01

Wind energy has demonstrated to be a clean, copious and absolutely renewable source of energy, and the large penetration of it into the power grid indicates that wind energy is considered an effective means of power generation, Transmission of wind energy from remote locations to load centers necessitates long transmission lines. Series compensation is a proven and economical transmission solution to address system power transfer strength, grid stability, and voltage profile issues of long transmission lines. In this paper, a programmable approach to determine the capacitive reactance of series capacitor and optimum location for its placement to achieve maximum power transfer gas been presented. The respective program with sample solutions has been provided for real-time applications. (paper)

Wind Tunnel Tests for Wind Pressure Distribution on Gable Roof Buildings

Science.gov (United States)

2013-01-01

Gable roof buildings are widely used in industrial buildings. Based on wind tunnel tests with rigid models, wind pressure distributions on gable roof buildings with different aspect ratios were measured simultaneously. Some characteristics of the measured wind pressure field on the surfaces of the models were analyzed, including mean wind pressure, fluctuating wind pressure, peak negative wind pressure, and characteristics of proper orthogonal decomposition results of the measured wind pressure field. The results show that extremely high local suctions often occur in the leading edges of longitudinal wall and windward roof, roof corner, and roof ridge which are the severe damaged locations under strong wind. The aspect ratio of building has a certain effect on the mean wind pressure coefficients, and the effect relates to wind attack angle. Compared with experimental results, the region division of roof corner and roof ridge from AIJ2004 is more reasonable than those from CECS102:2002 and MBMA2006.The contributions of the first several eigenvectors to the overall wind pressure distributions become much bigger. The investigation can offer some basic understanding for estimating wind load distribution on gable roof buildings and facilitate wind-resistant design of cladding components and their connections considering wind load path. PMID:24082851

Offshore winds from a new generation of European satellites

DEFF Research Database (Denmark)

Badger, Merete; Karagali, Ioanna; Ahsbahs, Tobias Torben

at sea. All are important for the planning, operation, and maintenance of offshore wind farms. Typical shortcomings of SAR-based wind fields include a low sampling frequency and a need for advanced data processing in order to retrieve the wind speed at 10 m above sea level. A new generation of European...... satellites and services could lower these barriers for applications in wind energy significantly. The Sentinel-1 A/B missions by the European Space Agency (ESA) deliver C-band SAR observations at an unprecedented coverage and spatial resolution. Over the seas of Europe, approximately 200 new acquisitions...... of Europe over time. The accuracy of this new product is currently under investigation. TerraSAR-X is an X-band SAR mission by the German Aerospace Center (DLR). It offers very high-resolution imagery, which may be used for detailed studies of e.g. wind farm wakes. TerraSAR-X imagery is acquired on...

Diel variation of ichthyoplankton recruitment in a wind-dominated temperate coastal lagoon (Argentina)

Science.gov (United States)

Bruno, Daniel O.; Delpiani, Sergio M.; Acha, Eduardo M.

2018-05-01

This study aimed to assess the diel changes of ichthyoplankton occurrence, during a known recruitment period, to a wind-dominated coastal lagoon (Argentina). We collected plankton samples at three sites of the lagoon's inlet area every 3 h during four 24 h cycles in mid austral summer. For each early-life history stage (eggs, yolk sac, preflexion larvae, postflexion larvae and early juveniles), the relationship between the abundance and possible combinations of the time of sampling, the wind effect, the wave period and the tidal state was evaluated by fitting generalized linear mix-effects models (GLMM). The wind effects depending on the time of sampling mainly affected fish abundance in all developmental stages. Overall, the highest abundances were collected at nocturnal hours when low-speed offshore winds blew. In addition, higher abundances of eggs, yolk sac and preflexion larvae were related to the incoming flood tide; whereas higher abundances of postflexion larvae and early juveniles were related to longer wave periods. We argued that the daily variation in the abundance of early-life history stages of fishes is related to the sea-land breeze cycle. Therefore, a conceptual framework of the recruitment process of eggs, larvae and early juveniles of fishes into this estuarine system considering the daily effect of winds is proposed.

Model Predictive Control of Wind Turbines using Uncertain LIDAR Measurements

DEFF Research Database (Denmark)

Mirzaei, Mahmood; Soltani, Mohsen; Poulsen, Niels Kjølstad

2013-01-01

, we simplify state prediction for the MPC. Consequently, the control problem of the nonlinear system is simplified into a quadratic programming. We consider uncertainty in the wind propagation time, which is the traveling time of wind from the LIDAR measurement point to the rotor. An algorithm based......The problem of Model predictive control (MPC) of wind turbines using uncertain LIDAR (LIght Detection And Ranging) measurements is considered. A nonlinear dynamical model of the wind turbine is obtained. We linearize the obtained nonlinear model for different operating points, which are determined...... on wind speed estimation and measurements from the LIDAR is devised to find an estimate of the delay and compensate for it before it is used in the controller. Comparisons between the MPC with error compensation, the MPC without error compensation and an MPC with re-linearization at each sample point...

Wind Loads on Structures

DEFF Research Database (Denmark)

Dyrbye, Claes; Hansen, Svend Ole

Wind loads have to be taken into account when designing civil engineering structures. The wind load on structures can be systematised by means of the wind load chain: wind climate (global), terrain (wind at low height), aerodynamic response (wind load to pressure), mechanical response (wind...... pressure to structural response) and design criteria. Starting with an introduction of the wind load chain, the book moves on to meteorological considerations, atmospheric boundary layer, static wind load, dynamic wind load and scaling laws used in wind-tunnel tests. The dynamic wind load covers vibrations...... induced by wind turbulence, vortex shedding, flutter and galloping. The book gives a comprehensive treatment of wind effects on structures and it will be useful for consulting engineers designing wind-sensitive structures. It will also be valuable for students of civil engineering as textbook...

Southern Hemisphere Upper Thermospheric Wind Climatology

Science.gov (United States)

Dhadly, M. S.; Emmert, J. T.; Drob, D. P.

2017-12-01

This study is focused on the poorly understood large-scale upper thermospheric wind dynamics in the southern polar cap, auroral, and mid latitudes. The gaps in our understanding of the dynamic high-latitude thermosphere are largely due to the sparseness of thermospheric wind measurements. Using data from current observational facilities, it is unfeasible to construct a synoptic picture of the Southern Hemisphere upper thermospheric winds. However, enough data with wide spatial and temporal coverage have accumulated to construct a meaningful statistical analysis of winds as function of season, magnetic latitude, and magnetic local time. We use long-term data from nine ground-based stations located at different southern high latitudes and three space-based instruments. These diverse data sets possess different geometries and different spatial and solar coverage. The major challenge of the effort is to combine these disparate sources of data into a coherent picture while overcoming the sampling limitations and biases among the datasets. Our preliminary analyses show mutual biases present among some of them. We first address the biases among various data sets and then combine them in a coherent way to construct maps of neutral winds for various seasons. We then validate the fitted climatology against the observational data and compare with corresponding fits of 25 years of simulated winds from the National Center for Atmospheric Research Thermosphere-Ionosphere-Electrodynamics General Circulation Model. This study provides critical insight into magnetosphere-ionosphere-thermosphere coupling and sets a necessary benchmark for validating new observations and tuning first-principles models.

A simple method to downscale daily wind statistics to hourly wind data

OpenAIRE

Guo, Zhongling

2013-01-01

Wind is the principal driver in the wind erosion models. The hourly wind speed data were generally required for precisely wind erosion modeling. In this study, a simple method to generate hourly wind speed data from daily wind statistics (daily average and maximum wind speeds together or daily average wind speed only) was established. A typical windy location with 3285 days (9 years) measured hourly wind speed data were used to validate the downscaling method. The results showed that the over...

Does green consumerism increase the acceptance of wind power?

International Nuclear Information System (INIS)

Thøgersen, John; Noblet, Caroline

2012-01-01

In this paper, we discuss what might be termed an action-based learning approach to promoting important pro-environmental actions, such as support for or acceptance of environmental policy. Such an approach involves promoting simple and easy behaviours as entry points for more radical steps towards sustainability, referred to as “catalytic” or “wedge” behaviours. Despite the obvious need for innovative approaches to promote important pro-environmental behaviour, and sound theoretical backing for such concepts, there is a lack of research testing the key propositions of this approach. In a survey study based on a random sample of residents of the state of Maine, USA, we find that both everyday “green” behaviour and the acceptance of an expansion of wind power are rooted in environmental concern and that everyday “green” behaviour gives a significant contribution to predicting acceptance of wind power when controlling for environmental concern. Hence, the promotion of everyday “green” behaviours may prepare the grounds for increasing acceptance of more far-reaching changes in the population, such as an expansion of wind power. - Highlights: ► Acceptance of wind power increases with environmental concern. ► So does everyday “green” consumerism. ► Green consumerism further increases acceptance of wind power. ► The effect of environmental concern on acceptance is partly mediated through green consumerism. ► Participants in the study are a random sample of residents of Maine, USA.

Test Results of a Nb3Sn Wind/React ''Stress-Managed'' Block Dipole

International Nuclear Information System (INIS)

McInturff, A.; Bish, P.; Blackburn, R.; Diaczenko, N.; Elliott, T.; Hafalia Jr., R.; Henchel, W.; Jaisle, A.; Lau, W.; Lietzke, A.; McIntyre, P.; Noyes, P.; Nyman, M.; Sattarov, A.; Sattarov, A.

2006-01-01

A second phase of a highfield dipole technology development has been tested. A Nb3Sn block-coil model dipole was fabricated, using magnetic mirror geometry and wind/react coil technology. The primary objective of this phase was to make a first experimental test of the stress-management strategy pioneered at Texas A and M. In this strategy a high-strength support matrix is integrated with the windings to intercept Lorentz stress from the inner winding so that it does not accumulate in the outer winding. The magnet attained a field that was consistent with short sample limit on the first quench; there was no training. The decoupling of Lorentz stress between inner and outer windings was validated. In ramp rate studies the magnet exhibited a remarkable robustness in rapid ramping operation. It reached 85 percent of short sample(ss) current even while ramping 2-3 T/s. This robustness is attributed to the orientation of the Rutherford cables parallel to the field in the windings, instead of the transverse orientation that characterizes common dipole designs. Test results are presented and the next development phase plans are discussed

Cost optimization of wind turbines for large-scale offshore wind farms

International Nuclear Information System (INIS)

Fuglsang, P.; Thomsen, K.

1998-02-01

This report contains a preliminary investigation of site specific design of off-shore wind turbines for a large off-shore wind farm project at Roedsand that is currently being proposed by ELKRAFT/SEAS. The results were found using a design tool for wind turbines that involve numerical optimization and aeroelastic calculations of response. The wind climate was modeled in detail and a cost function was used to estimate costs from manufacture and installation. Cost of energy is higher for off-shore installations. A comparison of an off-shore wind farm site with a typical stand alone on-shore site showed an increase of the annual production of 28% due to the difference in wind climate. Extreme loads and blade fatigue loads were nearly identical, however,fatigue loads on other main components increased significantly. Optimizations were carried out to find the optimum overall off-shore wind turbine design. A wind turbine for the off-shore wind farm should be different compared with a stand-alone on-shore wind turbine. The overall design changed were increased swept area and rated power combined with reduced rotor speed and tower height. Cost was reduced by 12% for the final 5D/14D off-shore wind turbine from 0.306 DKr/kWh to 0.270 DKr/kWh. These figures include capital costs from manufacture and installation but not on-going costs from maintenance. These results make off-shore wind farms more competitive and comparable to the reference on-shore stand-alone wind turbine. A corresponding reduction of cost of energy could not be found for the stand alone on-shore wind turbine. Furthermore the fatigue loads on wind turbines in on-shore wind farms will increase and cost of energy will increase in favor of off-shore wind farms. (au) EFP-95; EU-JOULE-3; 21 tabs., 7 ills., 8 refs

Damping Wind and Wave Loads on a Floating Wind Turbine

DEFF Research Database (Denmark)

Christiansen, Søren; Bak, Thomas; Knudsen, Torben

2013-01-01

Offshore wind energy capitalizes on the higher and less turbulent wind speeds at sea. To enable deployment of wind turbines in deep-water locations, structures are being explored, where wind turbines are placed on a floating platform. This combined structure presents a new control problem, due......, and we show the influence that both wind speed, wave frequencies and misalignment between wind and waves have on the system dynamics. A new control model is derived that extends standard turbine models to include the hydrodynamics, additional platform degrees of freedom, the platform mooring system...

Optimal Locations for Siting Wind Energy Projects: Technical Challenges, Economics, and Public Preferences

Science.gov (United States)

Lamy, Julian V.

40 TWh of new wind generation in the Midwestern transmission system (MISO) while minimizing system costs. Results show that building wind farms in North/South Dakota (windiest states) compared to Illinois (less windy, but close to population centers) would only be economical if the incremental transmission costs to access them were below 360/kW of wind capacity (break-even value). Historically, the incremental transmission costs for wind development in North/South Dakota compared to in Illinois are about twice this value. However, the break-even incremental transmission cost for wind farms in Minnesota/Iowa (also windy states) is 250/kW, which is consistent with historical costs. I conclude that for the case in MISO, building wind projects in more distant locations (i.e., Minnesota/Iowa) is most economical. My two final chapters use semi-structured interviews (Chapter 4) and conjoint-based surveys (Chapter 5) to understand public perceptions and preferences for different wind project siting characteristics such as the distance between the project and a person's home (i.e., "not-in-my-backyard" or NIMBY) and offshore vs. onshore locations. The semi-structured interviews, conducted with members of a community in Massachusetts, revealed that economic benefit to the community is the most important factor driving perceptions about projects, along with aesthetics, noise impacts, environmental benefits, hazard to wildlife, and safety concerns. In Chapter 5, I show the results from the conjoint survey. The study's sample included participants from a coastal community in Massachusetts and a U.S.-wide sample from Amazon's Mechanical Turk. Results show that participants in the U.S.-wide sample perceived a small reduction in utility, equivalent to $1 per month, for living within 1 mile of a project. Surprisingly, I find no evidence of this effect for participants in the coastal community. The most important characteristic to both samples was the economic benefits from the

Calculation of depleted wind resources near wind farms

DEFF Research Database (Denmark)

Nielsen, Morten

2015-01-01

Traditional wind resource maps include wind distribution, energy density and potential power production without wake effects. Adding wake effect to such maps is feasible by means of a new method based on Fourier transformation,and the extra computational work is comparable to that of the basic wind...

He II {lambda}4686 IN {eta} CARINAE: COLLAPSE OF THE WIND-WIND COLLISION REGION DURING PERIASTRON PASSAGE

Energy Technology Data Exchange (ETDEWEB)

Teodoro, M.; Damineli, A. [Instituto de Astronomia, Geofisica e Ciencias Atmosfericas, Universidade de Sao Paulo, Rua do Matao 1226, Cidade Universitaria, Sao Paulo 05508-900 (Brazil); Arias, J. I. [Departamento de Fisica, Universidad de La Serena, Av. Cisternas 1200 Norte, La Serena (Chile); De Araujo, F. X.; Borges Fernandes, M.; Pereira, C. B. [Observatorio Nacional, Rua General Jose Cristino 77, Sao Cristovao, Rio de Janeiro 20921-400 (Brazil); Barba, R. H.; Gonzalez, J. F. [Instituto de Ciencias Astronomicas, de la Tierra, y del Espacio (ICATE-CONICET), Avenida Espana Sur 1512, J5402DSP San Juan (Argentina); Corcoran, M. F. [CRESST and X-ray Astrophysics Laboratory, NASA/Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Fernandez-Lajus, E.; Gamen, R. C.; Solivella, G. R. [Facultad de Ciencias Astronomicas y Geofisicas, Universidad Nacional de La Plata, Paseo del Bosque s/n, La Plata, BA, B1900FWA (Argentina); Fraga, L. [Southern Observatory for Astrophysical Research, Colina El Pino s/n, Casilla 603, La Serena (Chile); Groh, J. H. [Max-Planck-Institute fuer Radioastronomie, Auf dem Huegel 69, D-53121 Bonn (Germany); Marshall, J. L. [Department of Physics and Astronomy, Texas A and M University, College Station, TX 77843-4242 (United States); McGregor, P. J.; Nicholls, D. C.; Parkin, E. R. [Research School of Astronomy and Astrophysics (RSAA), Mount Stromlo Observatory, Cotter Road, Weston, ACT 2611 (Australia); Morrell, N.; Phillips, M. M., E-mail: mairan@astro.iag.usp.br [Las Campanas Observatory, Observatories of the Carnegie Institution of Washington, Casilla 601, La Serena (Chile); and others

2012-02-10

The periodic spectroscopic events in {eta} Carinae are now well established and occur near the periastron passage of two massive stars in a very eccentric orbit. Several mechanisms have been proposed to explain the variations of different spectral features, such as an eclipse by the wind-wind collision (WWC) boundary, a shell ejection from the primary star or accretion of its wind onto the secondary. All of them have problems explaining all the observed phenomena. To better understand the nature of the cyclic events, we performed a dense monitoring of {eta} Carinae with five Southern telescopes during the 2009 low-excitation event, resulting in a set of data of unprecedented quality and sampling. The intrinsic luminosity of the He II {lambda}4686 emission line (L {approx} 310 L{sub Sun }) just before periastron reveals the presence of a very luminous transient source of extreme UV radiation emitted in the WWC region. Clumps in the primary's wind probably explain the flare-like behavior of both the X-ray and He II {lambda}4686 light curves. After a short-lived minimum, He II {lambda}4686 emission rises again to a new maximum, when X-rays are still absent or very weak. We interpret this as a collapse of the WWC onto the 'surface' of the secondary star, switching off the hard X-ray source and diminishing the WWC shock cone. The recovery from this state is controlled by the momentum balance between the secondary's wind and the clumps in the primary's wind.

He II λ4686 IN η CARINAE: COLLAPSE OF THE WIND-WIND COLLISION REGION DURING PERIASTRON PASSAGE

International Nuclear Information System (INIS)

Teodoro, M.; Damineli, A.; Arias, J. I.; De Araújo, F. X.; Borges Fernandes, M.; Pereira, C. B.; Barbá, R. H.; González, J. F.; Corcoran, M. F.; Fernández-Lajús, E.; Gamen, R. C.; Solivella, G. R.; Fraga, L.; Groh, J. H.; Marshall, J. L.; McGregor, P. J.; Nicholls, D. C.; Parkin, E. R.; Morrell, N.; Phillips, M. M.

2012-01-01

The periodic spectroscopic events in η Carinae are now well established and occur near the periastron passage of two massive stars in a very eccentric orbit. Several mechanisms have been proposed to explain the variations of different spectral features, such as an eclipse by the wind-wind collision (WWC) boundary, a shell ejection from the primary star or accretion of its wind onto the secondary. All of them have problems explaining all the observed phenomena. To better understand the nature of the cyclic events, we performed a dense monitoring of η Carinae with five Southern telescopes during the 2009 low-excitation event, resulting in a set of data of unprecedented quality and sampling. The intrinsic luminosity of the He II λ4686 emission line (L ∼ 310 L ☉ ) just before periastron reveals the presence of a very luminous transient source of extreme UV radiation emitted in the WWC region. Clumps in the primary's wind probably explain the flare-like behavior of both the X-ray and He II λ4686 light curves. After a short-lived minimum, He II λ4686 emission rises again to a new maximum, when X-rays are still absent or very weak. We interpret this as a collapse of the WWC onto the 'surface' of the secondary star, switching off the hard X-ray source and diminishing the WWC shock cone. The recovery from this state is controlled by the momentum balance between the secondary's wind and the clumps in the primary's wind.

Climatic wind tunnel for wind engineering tasks

Czech Academy of Sciences Publication Activity Database

Kuznetsov, Sergeii; Pospíšil, Stanislav; Král, Radomil

2015-01-01

Roč. 112, 2-B (2015), s. 303-316 ISSN 1897-628X R&D Projects: GA ČR(CZ) GA14-12892S Keywords : climatic tunnel * wind tunnel * atmospheric boundary layer * flow resistance * wind tunnel contraction Subject RIV: JM - Building Engineering https://suw.biblos.pk.edu.pl/resources/i5/i6/i6/i7/i6/r56676/KuznetsovS_ClimaticWind.pdf

Progress in wind tunnel experimental techniques for wind turbine?

Institute of Scientific and Technical Information of China (English)

Jingping XIAO; Li CHEN; Qiang WANG; Qiao WANG

2016-01-01

Based on the unsteady aerodynamics experiment (UAE) phase VI and the model experiment in controlled conditions (MEXICO) projects and the related research carried out in China Aerodynamic Research and Development Center (CARDC), the recent progress in the wind tunnel experimental techniques for the wind turbine is sum-marized. Measurement techniques commonly used for di?erent types of wind tunnel ex-periments for wind turbine are reviewed. Important research achievements are discussed, such as the wind tunnel disturbance, the equivalence of the airfoil in?ow condition, the three-dimensional (3D) e?ect, the dynamic in?ow in?uence, the ?ow ?eld structure, and the vortex induction. The corresponding research at CARDC and some ideas on the large wind turbine are also introduced.

3D WindScanner lidar measurements of wind and turbulence around wind turbines, buildings and bridges

DEFF Research Database (Denmark)

Mikkelsen, Torben Krogh; Sjöholm, Mikael; Angelou, Nikolas

2017-01-01

WindScanner is a distributed research infrastructure developed at DTU with the participation of a number of European countries. The research infrastructure consists of a mobile technically advanced facility for remote measurement of wind and turbulence in 3D. The WindScanners provide coordinated...... structures and of flow in urban environments. The mobile WindScanner facility enables 3D scanning of wind and turbulence fields in full scale within the atmospheric boundary layer at ranges from 10 meters to 5 (10) kilometers. Measurements of turbulent coherent structures are applied for investigation...

Prospects for development of wind turbines with orthogonal rotor

Science.gov (United States)

Gorelov, D. N.; Krivospitsky, V. P.

2008-03-01

The experimental data obtained previously on the investigation of power characteristics and the possibility of the self-start of the Darrieus rotor are anlysed. These results are used at the design of new two-tier wind turbines with straight blades. The full-scale tests of two design variants showed the prospects for the development of wind turbines with the Darrieus rotor. At a reasonable design, they do not need any devices for the rotor orientation and start-up, are little sensitive to wind gusts and can have a high level of power characteristics, which is not inferior to the best samples of the units of propeller type.

The effect of wind power installations on coastal tourism

International Nuclear Information System (INIS)

Blaydes Lilley, M.; Firestone, J.; Kempton, W.

2010-01-01

We surveyed more than 1,000 randomly sampled, out-of-state tourists at Delaware, USA beaches in 2007. After providing respondents with wind turbine project photo-simulations at several distances, we inquired about the effect development would have on visitation. Approximately one-quarter stated that they would switch beaches if an offshore wind project was located 10 km from the coast, with avoidance diminishing with greater distance from shore. Stated avoidance is less than: avoidance with a fossil fuel power plant located the same distance inland; attraction to a beach with offshore wind turbines; and the percentage stating they would likely pay to take a boat tour. (author)

The Effect of Wind Power Installations on Coastal Tourism

Directory of Open Access Journals (Sweden)

Willett Kempton

2010-01-01

Full Text Available We surveyed more than 1,000 randomly sampled, out-of-state tourists at Delaware, USA beaches in 2007. After providing respondents with wind turbine project photo-simulations at several distances, we inquired about the effect development would have on visitation. Approximately one-quarter stated that they would switch beaches if an offshore wind project was located 10 km from the coast, with avoidance diminishing with greater distance from shore. Stated avoidance is less than: avoidance with a fossil fuel power plant located the same distance inland; attraction to a beach with offshore wind turbines; and the percentage stating they would likely pay to take a boat tour.

The effect of wind power installations on coastal tourism

Energy Technology Data Exchange (ETDEWEB)

Blaydes Lilley, M.; Firestone, J.; Kempton, W. [Center for Carbon-free Power Integration, College of Earth, Ocean, and Environment, University of Delaware, Newark, DE 19716 (United States)

2010-07-01

We surveyed more than 1,000 randomly sampled, out-of-state tourists at Delaware, USA beaches in 2007. After providing respondents with wind turbine project photo-simulations at several distances, we inquired about the effect development would have on visitation. Approximately one-quarter stated that they would switch beaches if an offshore wind project was located 10 km from the coast, with avoidance diminishing with greater distance from shore. Stated avoidance is less than: avoidance with a fossil fuel power plant located the same distance inland; attraction to a beach with offshore wind turbines; and the percentage stating they would likely pay to take a boat tour. (author)

Sequence Domain Harmonic Modeling of Type-IV Wind Turbines

DEFF Research Database (Denmark)

Guest, Emerson; Jensen, Kim Høj; Rasmussen, Tonny Wederberg

2017-01-01

-sampled pulsewidth modulation and an analysis of converter generated voltage harmonics due to compensated dead-time. The decoupling capabilities of the proposed the SD harmonic model are verified through a power quality (PQ) assessment of a 3MW Type-IV wind turbine. The assessment shows that the magnitude and phase...... of low-order odd converter generated voltage harmonics are dependent on the converter operating point and the phase of the fundamental component of converter current respectively. The SD harmonic model can be used to make PQ assessments of Type-IV wind turbines or incorporated into harmonic load flows...... for computation of PQ in wind power plants....

Wind Turbine Generator System Acoustic Noise Test Report for the Gaia Wind 11-kW Wind Turbine

Energy Technology Data Exchange (ETDEWEB)

Huskey, A.

2011-11-01

This report details the acoustic noise test conducted on the Gaia-Wind 11-kW wind turbine at the National Wind Technology Center. The test turbine is a two- bladed, downwind wind turbine with a rated power of 11 kW. The test turbine was tested in accordance with the International Electrotechnical Commission standard, IEC 61400-11 Ed 2.1 2006-11 Wind Turbine Generator Systems -- Part 11 Acoustic Noise Measurement Techniques.

Cooperative wind turbine control for maximizing wind farm power using sequential convex programming

International Nuclear Information System (INIS)

Park, Jinkyoo; Law, Kincho H.

2015-01-01

Highlights: • The continuous wake model describes well the wake profile behind a wind turbine. • The wind farm power function describes well the power production of a wind farm. • Cooperative control increases the wind farm power efficiency by 7.3% in average. • SCP can be employed to efficiently optimize the control actions of wind turbines. - Abstract: This paper describes the use of a cooperative wind farm control approach to improve the power production of a wind farm. The power production by a downstream wind turbine can decrease significantly due to reduced wind speed caused by the upstream wind turbines, thereby lowering the overall wind farm power production efficiency. In spite of the interactions among the wind turbines, the conventional (greedy) wind turbine control strategy tries to maximize the power of each individual wind turbine by controlling its yaw angle, its blade pitch angle and its generator torque. To maximize the overall wind farm power production while taking the wake interference into account, this study employs a cooperative control strategy. We first derive the wind farm power as a differentiable function of the control actions for the wind turbines in a wind farm. The wind farm power function is then maximized using sequential convex programming (SCP) to determine the optimum coordinated control actions for the wind turbines. Using an example wind farm site and available wind data, we show how the cooperative control strategy improves the power production of the wind farm

Avaliação do torque para inserção, remoção e fratura de diferentes mini-implantes ortodônticos Evaluation of insertion, removal and fracture torques of different orthodontic mini-implants in bovine tibia cortex

Directory of Open Access Journals (Sweden)

Maria Fernanda Prates da Nova

2008-10-01

Full Text Available OBJETIVO: avaliar, em mini-implantes de diferentes dimensões, os seguintes fatores: (a torque de inserção, (b torque de remoção, (c torque de fratura, (d tensão cisalhante, (e tensão normal e (f tipo de fratura. METODOLOGIA: foram utilizados 20 mini-implantes autoperfurantes, 10 da marca SIN e 10 da Neodent com, respectivamente, 8 e 7mm de comprimento, todos com 1,6mm de diâmetro. Dos 10 mini-implantes de cada marca, 5 não possuíam perfil transmucoso e 5 tinham perfil de 2mm, formando 4 grupos: SIN sem perfil (SSP, SIN com perfil (SCP, Neodent sem perfil (NSP e Neodent com perfil (NCP. Todos os mini-implantes foram inseridos em cortical óssea e removidos com micromotor acoplado a um torquímetro. Os mini-implantes foram, também, submetidos ao ensaio de fratura. Os torques de inserção, remoção e fratura, assim como a tensão cisalhante e normal calculadas, foram comparados entre todos os grupos pela ANOVA. O tipo de fratura foi avaliado em microscópio eletrônico de varredura. RESULTADOS: verificou-se que o grupo NCP apresentou torque de inserção significativamente maior que os demais grupos, porém todos fraturaram durante a inserção (n = 2 ou remoção (n = 3. Não houve diferença entre os grupos para o torque de remoção. Para o grupo NSP, o torque de fratura foi significativamente menor do que todos os outros grupos. Todos os mini-implantes sofreram fratura do tipo dúctil. CONCLUSÃO: uma vez que não houve diferença na resistência mecânica de ambas as marcas, variando apenas a forma, conclui-se que a resistência à fratura pode ser afetada por esta variável.AIM: The purpose of this study was to evaluate mini-implants with different dimensions for the following factors: (a insertion torque, (b removal torque, (c fracture torque, (d shear tension, (e normal tension and (f type of fracture. METHODS: Twenty self-drilling mini-implants were used, 10 from SIN and 10 from Neodent, with 1.6mm in diameter and with 8 and 7

Monthly Wind Characteristics and Wind Energy in Rwanda

African Journals Online (AJOL)

user

Abstract. Evaluating wind power potential for a site is indispensable before making any decision for the installation of wind energy infrastructures and planning for relating projects. This paper presents a branch of a composite analysis whose objective was to investigate the potential of wind energy resource in Rwanda.

Design Mining Interacting Wind Turbines.

Science.gov (United States)

Preen, Richard J; Bull, Larry

2016-01-01

An initial study has recently been presented of surrogate-assisted evolutionary algorithms used to design vertical-axis wind turbines wherein candidate prototypes are evaluated under fan-generated wind conditions after being physically instantiated by a 3D printer. Unlike other approaches, such as computational fluid dynamics simulations, no mathematical formulations were used and no model assumptions were made. This paper extends that work by exploring alternative surrogate modelling and evolutionary techniques. The accuracy of various modelling algorithms used to estimate the fitness of evaluated individuals from the initial experiments is compared. The effect of temporally windowing surrogate model training samples is explored. A surrogate-assisted approach based on an enhanced local search is introduced; and alternative coevolution collaboration schemes are examined.

IEA Wind Task 26: Offshore Wind Farm Baseline Documentation

Energy Technology Data Exchange (ETDEWEB)

Smart, Gavin [Offshore Renewable Energy Catapult, Blyth, Northumberland (United Kingdom); Smith, Aaron [National Renewable Energy Lab. (NREL), Golden, CO (United States); Warner, Ethan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sperstad, Iver Bakken [SINTEF Energy Research, Trondheim (Norway); Prinsen, Bob [Ecofys, Utrecht (Netherlands). TKI Wind Op Zee; Lacal-Arantegui, Roberto [European Commission Joint Research Centre (JRC), Brussels (Belgium)

2016-06-02

This document has been produced to provide the definition and rationale for the Baseline Offshore Wind Farm established within IEA Wind Task 26--Cost of Wind Energy. The Baseline has been developed to provide a common starting point for country comparisons and sensitivity analysis on key offshore wind cost and value drivers. The baseline project reflects an approximate average of the characteristics of projects installed between 2012 and 2014, with the project life assumed to be 20 years. The baseline wind farm is located 40 kilometres (km) from construction and operations and maintenance (O&M) ports and from export cable landfall. The wind farm consists of 100 4-megawatt (MW) wind turbines mounted on monopile foundations in an average water depth of 25 metres (m), connected by 33-kilovolt (kV) inter-array cables. The arrays are connected to a single offshore substation (33kV/220kV) mounted on a jacket foundation, with the substation connected via a single 220kV export cable to an onshore substation, 10km from landfall. The wind farm employs a port-based O&M strategy using crew-transfer vessels.

Were chondrites magnetized by the early solar wind?

Science.gov (United States)

Oran, Rona; Weiss, Benjamin P.; Cohen, Ofer

2018-06-01

Chondritic meteorites have been traditionally thought to be samples of undifferentiated bodies that never experienced large-scale melting. This view has been challenged by the existence of post-accretional, unidirectional natural remanent magnetization (NRM) in CV carbonaceous chondrites. The relatively young inferred NRM age [∼10 million years (My) after solar system formation] and long duration of NRM acquisition (1-106 y) have been interpreted as evidence that the magnetizing field was that of a core dynamo within the CV parent body. This would imply that CV chondrites represent the primitive crust of a partially differentiated body. However, an alternative hypothesis is that the NRM was imparted by the early solar wind. Here we demonstrate that the solar wind scenario is unlikely due to three main factors: 1) the magnitude of the early solar wind magnetic field is estimated to be limits field amplification due to pile-up of the solar wind to less than a factor of 3.5 times that of the instantaneous solar wind field, and 3) the solar wind field likely changed over timescales orders of magnitude shorter than the timescale of NRM acquisition. Using analytical arguments, numerical simulations and astronomical observations of the present-day solar wind and magnetic fields of young stars, we show that the maximum mean field the ancient solar wind could have imparted on an undifferentiated CV parent body is <3.5 nT, which is 3-4 and 3 orders of magnitude weaker than the paleointensities recorded by the CV chondrites Allende and Kaba, respectively. Therefore, the solar wind is highly unlikely to be the source of the NRM in CV chondrites. Nevertheless, future high sensitivity paleomagnetic studies of rapidly-cooled meteorites with high magnetic recording fidelity could potentially trace the evolution of the solar wind field in time.

Modeling wind speed and wind power distributions in Rwanda

Energy Technology Data Exchange (ETDEWEB)

Safari, Bonfils [Department of Physics, National University of Rwanda, P.O. Box 117, Huye District, South Province (Rwanda)

2011-02-15

Utilization of wind energy as an alternative energy source may offer many environmental and economical advantages compared to fossil fuels based energy sources polluting the lower layer atmosphere. Wind energy as other forms of alternative energy may offer the promise of meeting energy demand in the direct, grid connected modes as well as stand alone and remote applications. Wind speed is the most significant parameter of the wind energy. Hence, an accurate determination of probability distribution of wind speed values is very important in estimating wind speed energy potential over a region. In the present study, parameters of five probability density distribution functions such as Weibull, Rayleigh, lognormal, normal and gamma were calculated in the light of long term hourly observed data at four meteorological stations in Rwanda for the period of the year with fairly useful wind energy potential (monthly hourly mean wind speed anti v{>=}2 m s{sup -1}). In order to select good fitting probability density distribution functions, graphical comparisons to the empirical distributions were made. In addition, RMSE and MBE have been computed for each distribution and magnitudes of errors were compared. Residuals of theoretical distributions were visually analyzed graphically. Finally, a selection of three good fitting distributions to the empirical distribution of wind speed measured data was performed with the aid of a {chi}{sup 2} goodness-of-fit test for each station. (author)

Wind power statistics and an evaluation of wind energy density

Energy Technology Data Exchange (ETDEWEB)

Jamil, M.; Parsa, S.; Majidi, M. [Materials and Energy Research Centre, Tehran (Iran, Islamic Republic of)

1995-11-01

In this paper the statistical data of fifty days` wind speed measurements at the MERC- solar site are used to find out the wind energy density and other wind characteristics with the help of the Weibull probability distribution function. It is emphasized that the Weibull and Rayleigh probability functions are useful tools for wind energy density estimation but are not quite appropriate for properly fitting the actual wind data of low mean speed, short-time records. One has to use either the actual wind data (histogram) or look for a better fit by other models of the probability function. (Author)

Wind Resource Estimation using QuikSCAT Ocean Surface Winds

DEFF Research Database (Denmark)

Xu, Qing; Zhang, Guosheng; Cheng, Yongcun

2011-01-01

In this study, the offshore wind resources in the East China Sea and South China Sea were estimated from over ten years of QuikSCAT scatterometer wind products. Since the errors of these products are larger close to the coast due to the land contamination of radar backscatter signal...... and the complexity of air-sea interaction processes, an empirical relationship that adjusts QuikSCAT winds in coastal waters was first proposed based on vessel measurements. Then the shape and scale parameters of Weibull function are determined for wind resource estimation. The wind roses are also plotted. Results...

Anholt offshore wind farm winds investigated from satellite images

DEFF Research Database (Denmark)

Hasager, Charlotte Bay; Badger, Merete; Volker, Patrick

, i.e. before the wind farm was constructed. Based on these data the wind resource is estimated. Concurrent Sentinel-1 SAR data and available SCADA and lidar data, kindly provided by DONG Energy and partners, for the period January 2013 to June 2015 account for ~70 images, while ~300 images...... are available for Sentinel-1 from July 2015 to February 2017. The Sentinel-1 wind maps are investigated for wind farm wake effects. Furthermore the results on wind resources and wakes are compared to the SCADA and model results from WRF, Park, Fuga and RANS models....

Wind Penetration with different wind turbine technologies in a weak grid

International Nuclear Information System (INIS)

Santos Fuentefria, Ariel; Castro Fernandez, Miguel A.; Martínez García, Antonio

2012-01-01

The insertion of wind energy into electric network may provoke stability problems due to stochastic character of wind. The variation in the wind causes voltage variation in the Point of Common Coupling (PCC). In a weakest system that variation is high. Another important factor is wind turbine technology. The use of grid-connected fixed speed wind generator introduces a great consumption of reactive power that can be compensated using different devices as capacitors bank or static var compensator (SVC or STATCOM). In the other hand the variable speed wind turbine have an electronic converter to control the reactive consumption to maintain the PCC voltage more stable. In this paper a comparison between the different types of wind turbines technology is show. It's analyzing the impact in wind power limit for different wind turbine technologies in a weak system. (author)

The MIGHTI Wind Retrieval Algorithm: Description and Verification

Science.gov (United States)

Harding, Brian J.; Makela, Jonathan J.; Englert, Christoph R.; Marr, Kenneth D.; Harlander, John M.; England, Scott L.; Immel, Thomas J.

2017-10-01

We present an algorithm to retrieve thermospheric wind profiles from measurements by the Michelson Interferometer for Global High-resolution Thermospheric Imaging (MIGHTI) instrument on NASA's Ionospheric Connection Explorer (ICON) mission. MIGHTI measures interferometric limb images of the green and red atomic oxygen emissions at 557.7 nm and 630.0 nm, spanning 90-300 km. The Doppler shift of these emissions represents a remote measurement of the wind at the tangent point of the line of sight. Here we describe the algorithm which uses these images to retrieve altitude profiles of the line-of-sight wind. By combining the measurements from two MIGHTI sensors with perpendicular lines of sight, both components of the vector horizontal wind are retrieved. A comprehensive truth model simulation that is based on TIME-GCM winds and various airglow models is used to determine the accuracy and precision of the MIGHTI data product. Accuracy is limited primarily by spherical asymmetry of the atmosphere over the spatial scale of the limb observation, a fundamental limitation of space-based wind measurements. For 80% of the retrieved wind samples, the accuracy is found to be better than 5.8 m/s (green) and 3.5 m/s (red). As expected, significant errors are found near the day/night boundary and occasionally near the equatorial ionization anomaly, due to significant variations of wind and emission rate along the line of sight. The precision calculation includes pointing uncertainty and shot, read, and dark noise. For average solar minimum conditions, the expected precision meets requirements, ranging from 1.2 to 4.7 m/s.

A Comparison of Wind Flow Models for Wind Resource Assessment in Wind Energy Applications

Directory of Open Access Journals (Sweden)

Mathieu Landry

2012-10-01

Full Text Available The objective of this work was to assess the accuracy of various coupled mesoscale-microscale wind flow modeling methodologies for wind energy applications. This is achieved by examining and comparing mean wind speeds from several wind flow modeling methodologies with observational measurements from several 50 m met towers distributed across the study area. At the mesoscale level, with a 5 km resolution, two scenarios are examined based on the Mesoscale Compressible Community Model (MC2 model: the Canadian Wind Energy Atlas (CWEA scenario, which is based on standard input data, and the CWEA High Definition (CWEAHD scenario where high resolution land cover input data is used. A downscaling of the obtained mesoscale wind climate to the microscale level is then performed, where two linear microscale models, i.e., MsMicro and the Wind Atlas Analysis and Application Program (WAsP, are evaluated following three downscaling scenarios: CWEA-WAsP, CWEA-MsMicro and CWEAHD-MsMicro. Results show that, for the territory studied, with a modeling approach based on the MC2 and MsMicro models, also known as Wind Energy Simulation Toolkit (WEST, the use of high resolution land cover and topography data at the mesoscale level helps reduce modeling errors for both the mesoscale and microscale models, albeit only marginally. At the microscale level, results show that the MC2-WAsP modeling approach gave substantially better results than both MC2 and MsMicro modeling approaches due to tweaked meso-micro coupling.

Wind speed dynamical model in a wind farm

DEFF Research Database (Denmark)

Soleimanzadeh, Maryam; Wisniewski, Rafal

2010-01-01

, the dynamic model for wind flow will be established. The state space variables are determined based on a fine mesh defined for the farm. The end goal of this method is to assist the development of a dynamical model of a wind farm that can be engaged for better wind farm control strategies....

On the Response of a Micro Wind Turbine to Wind-Speed Change

OpenAIRE

烏谷, 隆; 渡辺, 公彦; 大屋, 裕二

2004-01-01

To improve the efficiency of a wind turbine, it is more effective to use high-speed wind. A method collecting wind to get high-speed wind was experimentally studied. It was found that the brimmed diffuser was a good device to get high-speed wind. The brimmed diffuser accelerated approaching wind, and wind speed near its inlet became about 1.7 times. Using this brimmed diffuser, we have made a new micro wind turbine and been carrying out field experiment. In order realize the properties of the...

Optimal Excitation Controller Design for Wind Turbine Generator

Directory of Open Access Journals (Sweden)

A. K. Boglou

2011-01-01

Full Text Available An optimal excitation controller design based on multirate-output controllers (MROCs having a multirate sampling mechanismwith different sampling period in each measured output of the system is presented. The proposed H∞ -control techniqueis applied to the discrete linear open-loop system model which represents a wind turbine generator supplying an infinite busthrough a transmission line.

Aeolian transport of biota with dust: A wind tunnel experiment

Science.gov (United States)

Rivas, J. A., Jr.; Gill, T. E.; Van Pelt, R. S.; Walsh, E.

2015-12-01

Ephemeral wetlands are ideal sources for dust emission, as well as repositories for dormant stages of aquatic invertebrates. An important component of invertebrate dispersal and colonization to new areas is the ability to be entrained into the atmosphere. Aquatic invertebrate eggs fall within the size of dust and sand grains (30-600μm), are less dense and aerodynamically shaped. We have shown previously that aquatic invertebrates can be dispersed long distances in dust storms but the extent of transport of taxa based on diapausing egg size/morphology has not been investigated. Here, we control the wind erosion process in a wind tunnel to test entrainment of diapausing stages of brine shrimp, clam shrimp, tadpole shrimp, fairy shrimp, Daphnia, and the rotifers Brachionus plicatilis and B. calyciflorus into the air by saltation. Diapausing eggs were mixed with sterilized wind-erodible soil. The soil/egg mixture was moistened with distilled water and air dried to form a crust. Dust was generated in a wind tunnel by releasing sand grains that act as saltator material similar to wind-entrained natural sands. Maximum wind velocity was 10m/s and entrained particles were sampled through an isokinetic horizontal intake opening. Aeolian sediment was collected from three points in the system; transfer section for coarse sediment, the pan subtending a settling chamber for finer saltation-sized sediment, and two paper filters for suspension-sized sediment. Samples were then passed through 250 and 350 μm sieves to remove abrader sand and rehydrated with various sterile media depending on the type of organism. We retrieved viable brine, fairy, and tadpole shrimp, ostracods, Daphnia, and diapausing eggs of the rotifers after hydration. This experiment demonstrates that resting stages of many invertebrates can be wind-eroded due to size and egg morphology and remain viable under controlled conditions mimicking dust emission.

Wind Energy Japan

Energy Technology Data Exchange (ETDEWEB)

Komatsubara, Kazuyo [Embassy of the Kingdom of the Netherlands, Tokyo (Japan)

2012-06-15

An overview is given of wind energy in Japan: Background; Wind Energy in Japan; Japanese Wind Energy Industry; Government Supports; Useful Links; Major Japanese Companies; Profiles of Major Japanese Companies; Major Wind Energy Projects in Japan.

Prospecting for Wind

Science.gov (United States)

Swapp, Andy; Schreuders, Paul; Reeve, Edward

2011-01-01

Many people use wind to help meet their needs. Over the years, people have been able to harness or capture the wind in many different ways. More recently, people have seen the rebirth of electricity-generating wind turbines. Thus, the age-old argument about technology being either good or bad can also be applied to the wind. The wind can be a…

Fine tuning support vector machines for short-term wind speed forecasting

International Nuclear Information System (INIS)

Zhou Junyi; Shi Jing; Li Gong

2011-01-01

Research highlights: → A systematic approach to tuning SVM models for wind speed prediction is proposed. → Multiple kernel functions and a wide range of tuning parameters are evaluated, and optimal parameters for each kernel function are obtained. → It is found that the forecasting performance of SVM is closely related to the dynamic characteristics of wind speed. → Under the optimal combination of parameters, different kernels give comparable forecasting accuracy. -- Abstract: Accurate forecasting of wind speed is critical to the effective harvesting of wind energy and the integration of wind power into the existing electric power grid. Least-squares support vector machines (LS-SVM), a powerful technique that is widely applied in a variety of classification and function estimation problems, carries great potential for the application of short-term wind speed forecasting. In this case, tuning the model parameters for optimal forecasting accuracy is a fundamental issue. This paper, for the first time, presents a systematic study on fine tuning of LS-SVM model parameters for one-step ahead wind speed forecasting. Three SVM kernels, namely linear, Gaussian, and polynomial kernels, are implemented. The SVM parameters considered include the training sample size, SVM order, regularization parameter, and kernel parameters. The results show that (1) the performance of LS-SVM is closely related to the dynamic characteristics of wind speed; (2) all parameters investigated greatly affect the performance of LS-SVM models; (3) under the optimal combination of parameters after fine tuning, the three kernels give comparable forecasting accuracy; (4) the performance of linear kernel is worse than the other two kernels when the training sample size or SVM order is small. In addition, LS-SVMs are compared against the persistence approach, and it is found that they can outperform the persistence model in the majority of cases.

Some challenges of wind modelling for modern wind turbines: The Weibull distribution

DEFF Research Database (Denmark)

Gryning, Sven-Erik; Batchvarova, Ekatarina; Floors, Rogier

2012-01-01

Wind power assessments, as well as forecast of wind energy production, are key issues in wind energy and grid related studies. However the hub height of today’s wind turbines is well above the surface layer. Wind profiles studies based on mast data show that the wind profile above the surface layer...

Design optimization of offshore wind farms with multiple types of wind turbines

DEFF Research Database (Denmark)

Feng, Ju; Shen, Wen Zhong

2017-01-01

Most studies on offshore wind farm design assume a uniform wind farm, which consists of an identical type of wind turbines. In order to further reduce the cost of energy, we investigate the design of non-uniform offshore wind farms, i.e., wind farms with multiple types of wind turbines and hub-he...

Evolution of wind towards wind turbine

NARCIS (Netherlands)

Giyanani, A.H.; Bierbooms, W.A.A.M.; Van Bussel, G.J.W.

2015-01-01

Remote sensing of the atmospheric variables with the use of LiDAR is a relatively new technology field for wind resource assessment in wind energy. The validation of LiDAR measurements and comparisons is of high importance for further applications of the data.

Use of Bacillus pumilus CBMAI 0008 and Paenibacillus sp. CBMAI 868 for colour removal from paper mill effluent Emprego de Bacillus pumilus CBMAI 0008 e Paenibacillus sp. CBMAI 868 para remoção da cor do efluente da indústria papeleira

Directory of Open Access Journals (Sweden)

Patrícia Lopes de Oliveira

2009-06-01

Full Text Available Bacillus pumilus and Paenibacillus sp. were applied on the paper mill effluent to investigate the colour remotion. Inocula were individually applied in effluent at pH 7.0, 9.0 and 11.0. The real colour and COD remotion after 48h at pH 9.0 were, respectively, 41.87% and 22.08% for B. pumilus treatment and 42.30% and 22.89% for Paenibacillus sp. Gel permeation chromatography was used to verify the molar masses of compounds in the non-treated and treated effluent, showing a decrease in the compounds responsible for the paper mill effluent colour.Bacillus pumilus e Paenibacillus sp. foram aplicados separadamente no efluente da indústria papeleira a pH 7,0, 9,0 e 11,0, para verificação da remoção da cor e da DQO. As remoções da cor real e DQO após 48h a pH 9,0 foram, respectivamente, de 41,87% e 22,08% após o tratamento com B. pumilus e 42,30% e 22,89% após tratamento com Paenibacillus sp. As massas molares dos compostos presentes no efluente não tratado e tratado foram determinadas por cromatografia de permeação em gel. O emprego dos microrganismos reduziu os compostos responsáveis pela cor do efluente da indústria papeleira.

WindNet: Improving the impact assessment of wind power projects

Directory of Open Access Journals (Sweden)

Christopher R. Jones

2014-12-01

Full Text Available Growing international demand for renewable energy has led to rapid growth in the wind power sector and wind farms are becoming an increasingly common feature of landscapes and seascapes in many countries. However, as the most appropriate locations within established markets are taken up, and as wind power penetrates new markets, there is an increasing likelihood that proposed projects will encroach on sensitive landscapes and residential areas. This will present challenges for the industry, particularly due to the impact that public opinion can have upon the outcomes of planning decisions about specific projects. This article introduces the four key dimensions of the WindNet programme, which are helping to elucidate some of the socio-technical debates that will likely shape the future of the wind power sector. The article outlines studies investigating (1 public responses to cumulative landscape and visual impacts, (2 the auditory impact of wind power projects on human health, (3 the science of wind farm design and its implications for planning, and (4 the relevance of the democratic deficit explanation of the so-called "social gap" in wind farm siting. The outcomes of the research being conducted by WindNet stand to help reduce uncertainty within the planning process and assist in providing a more comprehensive and fairer assessment of the possible impacts associated with wind power project development.

Canadian Wind Energy Association small wind conference proceedings : small wind policy developments (turbines of 300 kW or less)

International Nuclear Information System (INIS)

2005-01-01

The small wind session at the Canadian Wind Energy Association's (CanWEA) annual conference addressed policies affecting small wind, such as net metering, advanced renewable tariffs and interconnections. It also addressed CanWEA's efforts in promoting small wind turbines, particularly in remote northern communities, small businesses and within the residential sector. Small wind systems are typically installed in remote communities to offset utility supplied electricity at the retail price level. In certain circumstances, small wind and hybrid systems can produce electricity at less than half the cost of traditional electricity sources, which in remote communities is typically diesel generators. Small wind turbines require different materials and technologies than large wind turbines. They also involve different local installation requirements, different by-laws, tax treatment and environmental assessments. Small wind turbines are typically installed for a range of factors, including energy independence, energy price stability and to lower environmental impacts of traditional power generation. The small wind session at the conference featured 14 presentations, of which 4 have been catalogued separately for inclusion in this database. tabs., figs

Wind: French revolutions

International Nuclear Information System (INIS)

Jones, C.

2006-01-01

Despite having the second best wind resources in Europe after the UK, the wind industry in France lags behind its European counterparts with just 6 W of installed wind capacity per person. The electricity market in France is dominated by the state-owned Electricite de France (EdF) and its nuclear power stations. However, smaller renewable generators are now in theory allowed access to the market and France has transposed the EU renewables directive into national law. The French governement has set a target of generating 10,000 MW of renewable capacity by 2010. The announcement of an increased feed-in tariff and the introduction of 'development zones' (ZDEs) which could allow fast-tracking of planning for wind projects are also expected to boost wind projects. But grid access and adminstrative burdens remain major barriers. In addition, French politicians and local authorities remain committed to nuclear, though encouraged by the European Commission, wind is beginning to gain acceptance; some 325 wind farms (representing 1557 MW of capacity) were approved between February 2004 and January 2005. France is now regarded by the international wind energy sector as a target market. One of France's leading independent wind developers and its only listed wind company, Theolia, is expected to be one of the major beneficiaries of the acceleration of activity in France, though other companies are keen to maximise the opportunities for wind. France currently has only one indigenous manufacturer of wind turbines, but foreign suppliers are winning orders

Wind energy systems

Science.gov (United States)

Stewart, H. J.

1978-01-01

A discussion on wind energy systems involved with the DOE wind energy program is presented. Some of the problems associated with wind energy systems are discussed. The cost, efficiency, and structural design of wind energy systems are analyzed.

Wind Predictions Upstream Wind Turbines from a LiDAR Database

Directory of Open Access Journals (Sweden)

Soledad Le Clainche

2018-03-01

Full Text Available This article presents a new method to predict the wind velocity upstream a horizontal axis wind turbine from a set of light detection and ranging (LiDAR measurements. The method uses higher order dynamic mode decomposition (HODMD to construct a reduced order model (ROM that can be extrapolated in space. LiDAR measurements have been carried out upstream a wind turbine at six different planes perpendicular to the wind turbine axis. This new HODMD-based ROM predicts with high accuracy the wind velocity during a timespan of 24 h in a plane of measurements that is more than 225 m far away from the wind turbine. Moreover, the technique introduced is general and obtained with an almost negligible computational cost. This fact makes it possible to extend its application to both vertical axis wind turbines and real-time operation.

Wind power today

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-04-01

This publication highlights initiatives of the US DOE`s Wind Energy Program. 1997 yearly activities are also very briefly summarized. The first article describes a 6-megawatt wind power plant installed in Vermont. Another article summarizes technical advances in wind turbine technology, and describes next-generation utility and small wind turbines in the planning stages. A village power project in Alaska using three 50-kilowatt turbines is described. Very brief summaries of the Federal Wind Energy Program and the National Wind Technology Center are also included in the publication.

Gallup poll: wind energy perception in France; Sondage perception de l'energie eolienne en France

Energy Technology Data Exchange (ETDEWEB)

Chartier, C. [Institut Synovate, 75 - Paris (France)

2003-01-01

This gallup poll was carried out in January 2003 by the Synovate institute on request of the French agency of environment and energy mastery (Ademe). It was made on a representative sample of 2090 people from different French regions, and on two over-samples of people living in the vicinity of wind farms in operation or in construction: 300 people in the Aude region and 230 people in the Finistere region. The wind energy remains widely accepted by French people (87%) and even more in areas close to wind farms (Aude: 98%, Finistere: 99%). The ecological and economical aspect of wind energy is the main advantage put forward (92%) while the aesthetics remains the main drawback (45%). (J.S.)

Financing wind projects

International Nuclear Information System (INIS)

Manson, J.

2006-01-01

This presentation reviewed some of the partnership opportunities available from GE Energy. GE Energy's ecomagination commitment has promised to double research investment, make customers true partners and reduce greenhouse gases (GHGs). GE Energy's renewable energy team provides a broad range of financial products, and has recently funded 30 wind farms and 2 large solar projects. The company has a diverse portfolio of technology providers and wind regimes, and is increasing their investment in technology. GE Energy recognizes that the wind industry is growing rapidly and has received increased regulatory support that is backed by strong policy and public support. It is expected that Canada will have 3006 wind projects either planned or under construction by 2007. According to GE Energy, successful wind financing is dependent on the location of the site and its wind resources, as well as on the wind developer's power sales agreement. The success of a wind project is also determined by clear financing goals. Site-specific data is needed to determine the quality of wind resource, and off-site data can also be used to provide validation. Proximity to load centres will help to minimize capital costs. Power sales agreements should be based on the project's realistic net capacity factor as well as on the cost of the turbines. The economics of many wind farms is driven by the size of the turbines used. Public consultations are also needed to ensure the success of wind power projects. It was concluded that a good partner will have staying power in the wind power industry, and will understand the time-lines and needs that are peculiar to wind energy developers. refs., tabs., figs

Wind energy

International Nuclear Information System (INIS)

Kotevski, Darko

2003-01-01

Wind is not only free, it is inexhaustible. Wind energy has come a very long way since the prototypes of just 20 years ago. today's wind turbines are state-of-the-art technology - modular and quick to install anywhere where there is sufficient wind potential to provide secure, centralised or distributed generation. It is a global phenomenon, the world's fastest growing energy sector, a clean and effective modern technology that completely avoids pollution and thus reducing the 'green house' effect. (Original)

Benchmarking U.S. Small Wind Costs with the Distributed Wind Taxonomy

Energy Technology Data Exchange (ETDEWEB)

Orrell, Alice C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Poehlman, Eric A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-10-04

The objective of this report is to benchmark costs for small wind projects installed in the United States using a distributed wind taxonomy. Consequently, this report is a starting point to help expand the U.S. distributed wind market by informing potential areas for small wind cost-reduction opportunities and providing a benchmark to track future small wind cost-reduction progress.

Wind energy statistics

International Nuclear Information System (INIS)

Holttinen, H.; Tammelin, B.; Hyvoenen, R.

1997-01-01

The recording, analyzing and publishing of statistics of wind energy production has been reorganized in cooperation of VTT Energy, Finnish Meteorological (FMI Energy) and Finnish Wind Energy Association (STY) and supported by the Ministry of Trade and Industry (KTM). VTT Energy has developed a database that contains both monthly data and information on the wind turbines, sites and operators involved. The monthly production figures together with component failure statistics are collected from the operators by VTT Energy, who produces the final wind energy statistics to be published in Tuulensilmae and reported to energy statistics in Finland and abroad (Statistics Finland, Eurostat, IEA). To be able to verify the annual and monthly wind energy potential with average wind energy climate a production index in adopted. The index gives the expected wind energy production at various areas in Finland calculated using real wind speed observations, air density and a power curve for a typical 500 kW-wind turbine. FMI Energy has produced the average figures for four weather stations using the data from 1985-1996, and produces the monthly figures. (orig.)

Wind energy power plants (wind farms) review and analysis

Energy Technology Data Exchange (ETDEWEB)

Newbold, K B; McKeary, M [McMaster Univ., Hamilton, ON (Canada). McMaster Inst. of Environment and Health

2010-07-01

Global wind power capacity has increased by an average cumulative rate of over 30 percent over the past 10 years. Although wind energy emits no air pollutants and facilities can often share spaces with other activities, public opposition to wind power development is an ongoing cause of concern. Development at the local level in Ontario has been met with fierce opposition on the basis of health concerns, aesthetic values, potential environmental impacts, and economic risks. This report was prepared for the Town of Wasaga Beach, and examined some of the controversy surrounding wind power developments through a review of evidence found in the scientific literature. The impacts of wind power developments related to noise, shadow flicker, avian mortality, bats, and real estate values were evaluated. The study included details of interviews conducted with individuals from Ontario localities where wind farms were located. 77 refs., 1 tab., 1 fig., 2 appendices.

Wind Resource Assessment – Østerild National Test Centre for Large Wind Turbines

OpenAIRE

Hansen, Brian Ohrbeck; Courtney, Michael; Mortensen, Niels Gylling

2014-01-01

This report presents a wind resource assessment for the seven test stands at the Østerild National Test Centre for Large Wind Turbines in Denmark. Calculations have been carried out mainly using wind data from three on-site wind lidars. The generalized wind climates applied in the wind resource calculations for the seven test stands are based on correlations between a short period of on-site wind data from the wind lidars with a long-term reference. The wind resource assessment for the seven ...

75 FR 47301 - Cedro Hill Wind LLC; Butler Ridge Wind Energy Center, LLC; High Majestic Wind Energy Center, LLC...

Science.gov (United States)

2010-08-05

...- 000; EG10-34-000; EG10-34-000; EG10-35-000; EG10-36-000; EG10-37-000; EG10-38-000] Cedro Hill Wind LLC; Butler Ridge Wind Energy Center, LLC; High Majestic Wind Energy Center, LLC; Wessington Wind Energy Center, LLC; Juniper Canyon Wind Power LLC; Loraine Windpark Project, LLC; White Oak Energy LLC; Meadow...

Urban Wind Energy

DEFF Research Database (Denmark)

Beller, Christina

important for the implementation of wind energy conversion systems are the macro and micro wind climate, the siting within a micro wind climate and the choice of a wind turbine model most appropriate for the selected site. In the frame of this work, all these important elements are analyzed and a row......New trends e.g. in architecture and urban planning are to reduce energy needs. Several technologies are employed to achieve this, and one of the technologies, not new as such, is wind energy. Wind turbines are installed in cities, both by companies and private persons on both old and new buildings....... However, an overview of the energy content of the wind in cities and how consequently turbines shall be designed for such wind climates is lacking. The objective of the present work is to deliver an objective and fundamental overview of the social, practical and physical conditions relevant...

Wind power barometer

International Nuclear Information System (INIS)

2014-01-01

The worldwide wind power increased by 12.4% in 2013 to reach 318.6 GW but the world market globally decreased by losing 10 GW: only 35.6 GW have been installed in 2013 which is even less than was installed in 2009. This activity contraction is mainly due to the collapse of the American market, American authorities having been late to decide to maintain federal incentives. The European wind power market also contracted in 2013 because of the lack of trust of the investors in the new energy policies of the European governments. In the rest of the world wind energy has kept on growing particularly in China and Canada. At the end of 2013 the cumulated wind power reached 117,73 GW in Europe. About 1.5 MW out of 10 MW of wind power installed in Europe in 2013 come from off-shore wind farms, United-Kingdom and Denmark being the most important players by totalling more than 70% of the off-shore wind power installed at the end of 2013. Various charts and tables give the figures of the wind power cumulated and installed in 2013 in different parts of the world: Europe, North America and Asia, the time evolution of the worldwide wind power since 1995, the wind power cumulated and installed in 2013 for the different countries of Europe and the ratio between the cumulated wind power and the country population. A table lists the main manufacturers of wind turbines and gives their turnover and number of employees at the end of 2013

Wind Data Analysis and Wind Flow Simulation Over Large Areas

Directory of Open Access Journals (Sweden)

Terziev Angel

2014-03-01

Full Text Available Increasing the share of renewable energy sources is one of the core policies of the European Union. This is because of the fact that this energy is essential in reducing the greenhouse gas emissions and securing energy supplies. Currently, the share of wind energy from all renewable energy sources is relatively low. The choice of location for a certain wind farm installation strongly depends on the wind potential. Therefore the accurate assessment of wind potential is extremely important. In the present paper an analysis is made on the impact of significant possible parameters on the determination of wind energy potential for relatively large areas. In the analysis the type of measurements (short- and long-term on-site measurements, the type of instrumentation and the terrain roughness factor are considered. The study on the impact of turbulence on the wind flow distribution over complex terrain is presented, and it is based on the real on-site data collected by the meteorological tall towers installed in the northern part of Bulgaria. By means of CFD based software a wind map is developed for relatively large areas. Different turbulent models in numerical calculations were tested and recommendations for the usage of the specific models in flows modeling over complex terrains are presented. The role of each parameter in wind map development is made. Different approaches for determination of wind energy potential based on the preliminary developed wind map are presented.

PV–wind hybrid power option for a low wind topography

International Nuclear Information System (INIS)

Bhattacharjee, Subhadeep; Acharya, Shantanu

2015-01-01

Highlights: • Optimally harness the wind energy by unification of solar resource. • Analysis of PV–wind hybrid system with tangible experience. • Cost of generation and renewable fraction are $0.488/kWh and 0.90 respectively. • Maximum wind penetration is observed to be 32.75% with installed PV–wind system. • Indicative annual grid electricity conservation is 90%. - Abstract: Solar and wind are clean energy sources with enormous potential to alleviate grid dependence. The paper aims to optimally harness the wind resource with the support of solar energy through hybrid technology for a north-east Indian state Tripura (low wind topography). Techno-economic analysis of a photovoltaic (PV)-wind hybrid simulation model has been performed for small scale application in an educational building. The study also evaluates the tangible performance of a similar plant in practical condition of the site. It has emerged from the study that major energy generation is turning out from PV segment which is promising almost all round the year. Nonetheless, a considerable amount of wind power is found to be generated during half of the year when average PV power production is comparatively less. The cost of electricity from the simulation model is found to be $0.488/kWh while renewable fraction in the total electricity share is obtained to be 0.90. From the actual performance of the plant, maximum wind penetration is observed to be 32.75%

Wind energy assessment and wind farm simulation in Triunfo - Pernambuco, Brazil

Energy Technology Data Exchange (ETDEWEB)

Lima, Laerte; Filho, Celso

2010-09-15

The Triunfo wind's characterization, in Pernambuco state, situated in Brazilian northeast, and wind power potential assessment study shows a average wind speed of 11.27 m / s, predominant Southeast wind direction, average wind power density of 1672 W/m2 and Weibull parameters shape and scale equal to 2,0 and 12,7 m/s. The wind farm was simulated by using 850kW wind turbines (total of 20MW). The simulated shows AEP of 111,4 GWh, Cf of 62% and 5462 hours of operation by year. The economical simulated results, shows Pay-back of 3 years, TIR = 47% and VAN = 85.506kEuro booths @ 20 years time period.

High resolution climatological wind measurements for wind energy applications

Energy Technology Data Exchange (ETDEWEB)

Bergstroem, H. [Uppsala Univ. (Sweden). Dept. of Meteorology

1996-12-01

Measurements with a combined cup anemometer/wind vane instrument, developed at the Department of Meteorology in Uppsala, is presented. The instrument has a frequency response of about 1 Hz, making it suitable not only for mean wind measurements, but also for studies of atmospheric turbulence. It is robust enough to be used for climatological purposes. Comparisons with data from a hot-film anemometer show good agreement, both as regards standard deviations and the spectral decomposition of the turbulent wind signal. The cup anemometer/wind vane instrument is currently used at three sites within the Swedish wind energy research programme. These measurements are shortly described, and a few examples of the results are given. 1 ref, 10 figs

Far offshore wind conditions in scope of wind energy

NARCIS (Netherlands)

Holtslag, M.C.

2016-01-01

Far offshore atmospheric conditions are favourable for wind energy purposes since mean wind speeds are relatively high (i.e., high power production) while turbulence levels are relatively low (i.e., less fatigue loads) compared to onshore conditions. Offshore wind energy, however, is still expensive

Operating wind turbines in strong wind conditions by using feedforward-feedback control

International Nuclear Information System (INIS)

Feng, Ju; Sheng, Wen Zhong

2014-01-01

Due to the increasing penetration of wind energy into power systems, it becomes critical to reduce the impact of wind energy on the stability and reliability of the overall power system. In precedent works, Shen and his co-workers developed a re-designed operation schema to run wind turbines in strong wind conditions based on optimization method and standard PI feedback control, which can prevent the typical shutdowns of wind turbines when reaching the cut-out wind speed. In this paper, a new control strategy combing the standard PI feedback control with feedforward controls using the optimization results is investigated for the operation of variable-speed pitch-regulated wind turbines in strong wind conditions. It is shown that the developed control strategy is capable of smoothening the power output of wind turbine and avoiding its sudden showdown at high wind speeds without worsening the loads on rotor and blades

Wind Vision: A New Era for Wind Power in the United States

Energy Technology Data Exchange (ETDEWEB)

U.S. Department of Energy

2015-03-12

With more than 4.5% of the nation's electricity supplied by wind energy today, the Department of Energy has collaborated with industry, environmental organizations, academic institutions, and national laboratories to develop a renewed Wind Vision, documenting the contributions of wind to date and envisioning a future where wind continues to provide key contributions to the nation’s energy portfolio. Building on and updating the 2008 20% Wind Energy by 2030 report, the new Wind Vision Report quantifies the economic, environmental, and social benefits of a robust wind energy future and the actions that wind stakeholders can take to make it a reality.

A spinner-integrated wind lidar for enhanced wind turbine control

DEFF Research Database (Denmark)

Mikkelsen, Torben; Angelou, Nikolas; Hansen, Kasper Hjorth

2013-01-01

A field test with a continuous wave wind lidar (ZephIR) installed in the rotating spinner of a wind turbine for unimpeded preview measurements of the upwind approaching wind conditions is described. The experimental setup with the wind lidar on the tip of the rotating spinner of a large 80 m roto...... of the spinner lidar data, is investigated. Finally, the potential for enhancing turbine control and performance based on wind lidar preview measurements in combination with feed-forward enabled turbine controllers is discussed. Copyright © 2012 John Wiley & Sons, Ltd....

Satellite winds as a tool for offshore wind resource assessment: The Great Lakes Wind Atlas

DEFF Research Database (Denmark)

Doubrawa, Paula; Barthelmie, Rebecca Jane; Pryor, Sara C.

2015-01-01

and combine all scenes into one wind speed map. QuikSCAT winds undergo a seasonal correction due to lack of data during the cold season that is based on its ratio relative to buoy time series. All processing steps reduce the biases of the individual maps relative to the buoy observed wind climates. The remote...

Earth aeolian wind streaks: Comparison to wind data from model and stations

Science.gov (United States)

Cohen-Zada, A. L.; Maman, S.; Blumberg, D. G.

2017-05-01

Wind streak is a collective term for a variety of aeolian features that display distinctive albedo surface patterns. Wind streaks have been used to map near-surface winds and to estimate atmospheric circulation patterns on Mars and Venus. However, because wind streaks have been studied mostly on Mars and Venus, much of the knowledge regarding the mechanism and time frame of their formation and their relationship to the atmospheric circulation cannot be verified. This study aims to validate previous studies' results by a comparison of real and modeled wind data with wind streak orientations as measured from remote-sensing images. Orientations of Earth wind streaks were statistically correlated to resultant drift direction (RDD) values calculated from reanalysis and wind data from 621 weather stations. The results showed good agreement between wind streak orientations and reanalysis RDD (r = 0.78). A moderate correlation was found between the wind streak orientations and the weather station data (r = 0.47); a similar trend was revealed on a regional scale when the analysis was performed by continent, with r ranging from 0.641 in North America to 0.922 in Antarctica. At sites where wind streak orientations did not correspond to the RDDs (i.e., a difference of 45°), seasonal and diurnal variations in the wind flow were found to be responsible for deviation from the global pattern. The study thus confirms that Earth wind streaks were formed by the present wind regime and they are indeed indicative of the long-term prevailing wind direction on global and regional scales.

Remoção de cistos de Giardia spp. e oocistos de Cryptosporidium spp. na Estação de Tratamento de Esgoto Garcia, no município de Blumenau, SC, Brasil

Directory of Open Access Journals (Sweden)

Mauro Giovanni Miglioli

2017-12-01

Full Text Available Giardia spp. e Cryptosporidium spp. são agentes etiológicos responsáveis por uma série de epidemias de gastroenterites ocorridas, principalmente, após o consumo de água contaminada. Os cistos e oocistos destes protozoários são resistentes às variações ambientais, bem como a maioria dos processos físicos, químicos e microbiológicos utilizados nas estações de tratamento de água e esgoto. Deste modo, este estudo teve como objetivo detectar e avaliar a remoção de cistos de Giardia spp. e oocistos de Cryptosporidium spp. no sistema de tratamento combinado anaeróbio + aeróbio da ETE Garcia em Blumenau, SC. Para efetuar a detecção de cistos e oocistos, as amostras de efluentes e lodos provenientes da ETE foram concentradas através de filtração em membranas de ésteres de celulose e centrifugação, seguida por reação de imunofluorescência direta (RID utilizando o Kit diagnóstico - Merifluor. Para a obtenção dos parâmetros físicos, químicos e microbiológicos, as análises seguiram os padrões preconizados em APHA (2012. Concentrações elevadas de cistos de Giardia spp. (máx. 900.000 cistos L-1 foram detectadas em 83,3% dos pontos analisados. Oocistos de Cryptosporidium spp. também foram detectados em elevadas concentrações (máx. 300.000 oocistos L-1 em 66,6% dos pontos analisados. Não foram detectados cistos e oocistos nas amostras do efluente tratado, deste modo o sistema combinado da ETE Garcia apresentou uma eficiência >99,9% para a remoção das formas resistentes destes patógenos, contribuindo para a redução da contaminação ambiental por protozoários patogênicos presentes no esgoto doméstico do município de Blumenau, SC, Brasil.

Statistics of LES simulations of large wind farms

DEFF Research Database (Denmark)

Andersen, Søren Juhl; Sørensen, Jens Nørkær; Mikkelsen, Robert Flemming

2016-01-01

. The statistical moments appear to collapse and hence the turbulence inside large wind farms can potentially be scaled accordingly. The thrust coefficient is estimated by two different reference velocities and the generic CT expression by Frandsen. A reference velocity derived from the power production is shown...... to give very good agreement and furthermore enables the very good estimation of the thrust force using only the steady CT-curve, even for very short time samples. Finally, the effective turbulence inside large wind farms and the equivalent loads are examined....

Wake losses optimization of offshore wind farms with moveable floating wind turbines

International Nuclear Information System (INIS)

Rodrigues, S.F.; Teixeira Pinto, R.; Soleimanzadeh, M.; Bosman, Peter A.N.; Bauer, P.

2015-01-01

Highlights: • We present a layout optimization framework for wind farms with moveable turbines. • Using moveable wind turbines in optimized layouts maximizes energy production. • Turbine and wind farm designers should cooperate to optimize offshore wind projects. - Abstract: In the future, floating wind turbines could be used to harvest energy in deep offshore areas where higher wind mean speeds are observed. Currently, several floating turbine concepts are being designed and tested in small scale projects; in particular, one concept allows the turbine to move after installation. This article presents a novel layout optimization framework for wind farms composed of moveable floating turbines. The proposed framework uses an evolutionary optimization strategy in a nested configuration which simultaneously optimizes the anchoring locations and the wind turbine position within the mooring lines for each individual wind direction. The results show that maximum energy production is obtained when moveable wind turbines are deployed in an optimized layout. In conclusion, the framework represents a new design optimization tool for future offshore wind farms composed of moveable floating turbines

Wind power plant

Energy Technology Data Exchange (ETDEWEB)

Caneghem, A.E. von

1975-07-24

The invention applies to a wind power plant in which the wind is used to drive windmills. The plant consists basically of a vertical tube with a lateral wind entrance opening with windmill on its lower end. On its upper end, the tube carries a nozzle-like top which increases the wind entering the tube by pressure decrease. The wind is thus made suitable for higher outputs. The invention is illustrated by constructional examples.

Danish Wind Power

DEFF Research Database (Denmark)

Lund, Henrik; Hvelplund, Frede; Østergaard, Poul Alberg

In a normal wind year, Danish wind turbines generate the equivalent of approx. 20 percent of the Danish electricity demand. This paper argues that only approx. 1 percent of the wind power production is exported. The rest is used to meet domestic Danish electricity demands. The cost of wind power...... misleading. The cost of CO2 reduction by use of wind power in the period 2004-2008 was only 20 EUR/ton. Furthermore, the Danish wind turbines are not paid for by energy taxes. Danish wind turbines are given a subsidy via the electricity price which is paid by the electricity consumers. In the recent years...... is paid solely by the electricity consumers and the net influence on consumer prices was as low as 1-3 percent on average in the period 2004-2008. In 2008, the net influence even decreased the average consumer price, although only slightly. In Denmark, 20 percent wind power is integrated by using both...

Use of Active Learning to Design Wind Tunnel Runs for Unsteady Cavity Pressure Measurements

Directory of Open Access Journals (Sweden)

Ankur Srivastava

2014-01-01

Full Text Available Wind tunnel tests to measure unsteady cavity flow pressure measurements can be expensive, lengthy, and tedious. In this work, the feasibility of an active machine learning technique to design wind tunnel runs using proxy data is tested. The proposed active learning scheme used scattered data approximation in conjunction with uncertainty sampling (US. We applied the proposed intelligent sampling strategy in characterizing cavity flow classes at subsonic and transonic speeds and demonstrated that the scheme has better classification accuracies, using fewer training points, than a passive Latin Hypercube Sampling (LHS strategy.

A high resolution global wind atlas - improving estimation of world wind resources

DEFF Research Database (Denmark)

Badger, Jake; Ejsing Jørgensen, Hans

2011-01-01

to population centres, electrical transmission grids, terrain types, and protected land areas are important parts of the resource assessment downstream of the generation of wind climate statistics. Related to these issues of integration are the temporal characteristics and spatial correlation of the wind...... resources. These aspects will also be addressed by the Global Wind Atlas. The Global Wind Atlas, through a transparent methodology, will provide a unified, high resolution, and public domain dataset of wind energy resources for the whole world. The wind atlas data will be the most appropriate wind resource...

InfraSound from wind turbines : observations from Castle River wind farm. Volume 1

International Nuclear Information System (INIS)

Edworthy, J.; Hepburn, H.

2005-01-01

Although infrasound has been discussed as a concern by groups opposed to wind farm facilities, there is very little information available about infrasound and wind turbines. This paper presented details of a project conducted by VisionQuest, the largest wind power producer in Canada. Three sensor types were used: precision sound analyzer, seismic geophones, and calibrated microphones to take measurements in low, medium and high winds. The project also measured infrasound when the wind farm was not operating. Acquisition geometry was presented, as well as details of apparent attenuations of wind noise. It was noted that high wind noise was a dominant factor and that there was little difference when the wind farm was not operational. It was suggested that turbines have no impact with high wind, since wind noise is not attenuated with distance. It was noted that increased geophone amplitudes indicate high wind coupled motion which is attenuated when the turbines are on. Results indicate that all frequencies showed attenuation with distance. Evidence showed that low frequency sound pressure levels were often lower when the turbines were switched on. Where turbines contributed to sound pressure levels, the magnitude of the contribution was below levels of concern to human health. Ambient sound pressure levels were much higher than contributions from wind turbines. It was concluded that wind itself generates infrasound. Wind turbines generate low levels of infrasound, detectable very close to facilities at low to medium wind speeds. Wind turbines may reduce ambient infrasound levels at high wind speeds by converting the energy from the wind into electricity. refs., tabs., figs

Wake characteristics of wind turbines in utility-scale wind farms

Science.gov (United States)

Yang, Xiaolei; Foti, Daniel; Sotiropoulos, Fotis

2017-11-01

The dynamics of turbine wakes is affected by turbine operating conditions, ambient atmospheric turbulent flows, and wakes from upwind turbines. Investigations of the wake from a single turbine have been extensively carried out in the literature. Studies on the wake dynamics in utility-scale wind farms are relatively limited. In this work, we employ large-eddy simulation with an actuator surface or actuator line model for turbine blades to investigate the wake dynamics in utility-scale wind farms. Simulations of three wind farms, i.e., the Horns Rev wind farm in Denmark, Pleasant Valley wind farm in Minnesota, and the Vantage wind farm in Washington are carried out. The computed power shows a good agreement with measurements. Analysis of the wake dynamics in the three wind farms is underway and will be presented in the conference. This work was support by Xcel Energy (RD4-13). The computational resources were provided by National Renewable Energy Laboratory.

Estonian wind climate

International Nuclear Information System (INIS)

Kull, Ain

1999-01-01

Estonia is situated on the eastern coast of the Baltic Sea. This is a region with intensive cyclonic activity and therefore with a relatively high mean wind speed. Atmospheric circulation and its seasonal variation determine the general character of the Estonian wind regime over the Atlantic Ocean and Eurasia. However, the Baltic sea itself is a very important factor affecting wind climate, it has an especially strong influence on the wind regime in costal areas. The mean energy density (W/m 2 ) is a wind energy characteristic that is proportional to the third power of wind speed and describes energy available in a flow of air through a unit area. The mean energy density is a characteristic which has practical importance in regional assessment of snowdrift, storm damage and wind energy

Reducing Wind Curtailment through Transmission Expansion in a Wind Vision Future

Energy Technology Data Exchange (ETDEWEB)

Jorgensen, Jennie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mai, Trieu [National Renewable Energy Lab. (NREL), Golden, CO (United States); Brinkman, Greg [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-01-01

The Department of Energy's 2015 Wind Vision study, which analyzed an ambitious scenario where wind power served 35% of U.S. electricity consumption in 2050, showed the potential for wind energy to provide substantial health, environmental, and economic benefits. Using a commercial unit commitment and economic dispatch model, we build on this research by assessing the hourly operational feasibility of a similar high wind future in the Western United States. Our detailed simulations found no hours of unmet load or reserve violations with more than 35% potential wind (and 12% potential solar) available on the system, which highlights the technical possibility of integrating large amounts of wind energy. However, absent significant changes to the western grid, we find that substantial wind curtailment could be an issue, as it could degrade the potential for wind power to reduce fuel costs and lowering the emission benefits. To assess the value of transmission to mitigate wind curtailment, we model a suite of transmission expansion scenarios. We find that wind curtailment could be reduced by approximately half under a scenario where new transmission is based only on proposed projects. This avoided wind curtailment could lower annual production costs and reduce carbon dioxide emissions substantially. Greater transmission expansion was found to yield further benefits, although the marginal benefits of these new lines were found to decline. Overall, these results suggest that power systems operation can be realized with more than 35% wind penetration, but that transmission expansion is likely to play a vital role.

Arctic wind energy

Energy Technology Data Exchange (ETDEWEB)

Peltola, E. [Kemijoki Oy (Finland); Holttinen, H.; Marjaniemi, M. [VTT Energy, Espoo (Finland); Tammelin, B. [Finnish Meteorological Institute, Helsinki (Finland)

1998-12-31

Arctic wind energy research was aimed at adapting existing wind technologies to suit the arctic climatic conditions in Lapland. Project research work included meteorological measurements, instrument development, development of a blade heating system for wind turbines, load measurements and modelling of ice induced loads on wind turbines, together with the development of operation and maintenance practices in arctic conditions. As a result the basis now exists for technically feasible and economically viable wind energy production in Lapland. New and marketable products, such as blade heating systems for wind turbines and meteorological sensors for arctic conditions, with substantial export potential, have also been developed. (orig.)

Arctic wind energy

International Nuclear Information System (INIS)

Peltola, E.; Holttinen, H.; Marjaniemi, M.; Tammelin, B.

1998-01-01

Arctic wind energy research was aimed at adapting existing wind technologies to suit the arctic climatic conditions in Lapland. Project research work included meteorological measurements, instrument development, development of a blade heating system for wind turbines, load measurements and modelling of ice induced loads on wind turbines, together with the development of operation and maintenance practices in arctic conditions. As a result the basis now exists for technically feasible and economically viable wind energy production in Lapland. New and marketable products, such as blade heating systems for wind turbines and meteorological sensors for arctic conditions, with substantial export potential, have also been developed. (orig.)

Wind Forcing of the Pacific Ocean Using Scatterometer Wind Data

Science.gov (United States)

Kelly, Kathryn A.

1999-01-01

The long-term objective of this research was an understanding of the wind-forced ocean circulation, particularly for the Pacific Ocean. To determine the ocean's response to the winds, we first needed to generate accurate maps of wind stress. For the ocean's response to wind stress we examined the sea surface height (SSH) both from altimeters and from numerical models for the Pacific Ocean.

The design of wind turbine for electrical power generation in Malaysian wind characteristics

International Nuclear Information System (INIS)

Abas Ab Wahab; Chong Wen Thong

2000-01-01

The paper describes the study of a wind turbine for electrical power generation in Malaysia wind characteristics. In this research, the wind turbine is designs based on the local wind characteristics and tries to avoid the problems faced in the past (turbine design, access, manpower and technical). The new wind turbine rotor design for a medium speed wind speed turbine utilises the concept of open-close type of horizontal axis (up-wind) wind turbine is intended to widen the optimum performance range for electrical generation in Malaysia wind characteristics. The wind turbine has been designed to cut-in at a lower speed, and to provide the rotation speed that high enough to run a generator. The analysis and design of new low speed wind turbine blades and open-close turbine rotor and prediction of turbine performance are being detailed in this paper. (Author)

IEA Task 32: Wind Lidar Systems for Wind Energy Deployment (LIDAR)

Energy Technology Data Exchange (ETDEWEB)

Kuhn, Martin; Trabucchi, Davide; Clifton, Andrew; Courtney, Mike; Rettenmeier, Andreas

2016-05-25

Under the International Energy Agency Wind Implementing Agreement (IEA Wind) Task 11, researchers started examining novel applications for remote sensing and the issues around them during the 51st topical expert meeting about remote sensing in January 2007. The 59th topical expert meeting organized by Task 11 in October 2009 was also dedicated to remote sensing, and the first draft of the Task's recommended practices on remote sensing was published in January 2013. The results of the Task 11 topical expert meetings provided solid groundwork for a new IEA Wind Task 32 on wind lidar technologies. Members of the wind community identified the need to consolidate the knowledge about wind lidar systems to facilitate their use, and to investigate how to exploit the advantages offered by this technology. This was the motivation that led to the start of IEA Wind Task 32 'Lidar Application for Wind Energy Deployment' in November 2011. The kick-off was meeting was held in May 2012.

Assessment of C-Type Darrieus Wind Turbine Under Low Wind Speed Condition

Science.gov (United States)

Misaran, M. S.; Rahman, Md. M.; Muzammil, W. K.; Ismail, M. A.

2017-07-01

Harvesting wind energy in in a low wind speed region is deem un-economical if not daunting task. Study shows that a minimum cut in speed of 3.5 m/s is required to extract a meaningful wind energy for electricity while a mean speed of 6 m/s is preferred. However, in Malaysia the mean speed is at 2 m/s with certain potential areas having 3 m/s mean speed. Thus, this work aims to develop a wind turbine that able to operate at lower cut-in speed and produce meaningful power for electricity generation. A C-type Darrieus blade is selected as it shows good potential to operate in arbitrary wind speed condition. The wind turbine is designed and fabricated in UMS labs while the performance of the wind turbine is evaluated in a simulated wind condition. Test result shows that the wind turbine started to rotate at 1 m/s compared to a NACA 0012 Darrieus turbine that started to rotate at 3 m/s. The performance of the turbine shows that it have good potential to be used in an intermittent arbitrary wind speed condition as well as low mean wind speed condition.

Reliability measures for indexed semi-Markov chains applied to wind energy production

International Nuclear Information System (INIS)

D'Amico, Guglielmo; Petroni, Filippo; Prattico, Flavio

2015-01-01

The computation of the dependability measures is a crucial point in many engineering problems as well as in the planning and development of a wind farm. In this paper we address the issue of energy production by wind turbines by using an indexed semi-Markov chain as a model of wind speed. We present the mathematical model, the data and technical characteristics of a commercial wind turbine (Aircon HAWT-10kW). We show how to compute some of the main dependability measures such as reliability, availability and maintainability functions. We compare the results of the model with real energy production obtained from data available in the Lastem station (Italy) and sampled every 10 min. - Highlights: • Semi-Markov models. • Time series generation of wind speed. • Computation of availability, reliability and maintainability.

Copula-based modeling of stochastic wind power in Europe and implications for the Swiss power grid

International Nuclear Information System (INIS)

Hagspiel, Simeon; Papaemannouil, Antonis; Schmid, Matthias; Andersson, Göran

2012-01-01

Highlights: ► We model stochastic wind power using copula theory. ► Stochastic wind power is integrated in a European system adequacy evaluation. ► The Swiss power grid is put at risk by further integrating wind power in Europe. ► System elements located at or close to Swiss borders are affected the most. ► A criticality indicator allows prioritizing expansion plans on a probabilistic basis. -- Abstract: Large scale integration of wind energy poses new challenges to the European power system due to its stochastic nature and often remote location. In this paper a multivariate uncertainty analysis problem is formulated for the integration of stochastic wind energy in the European grid. By applying copula theory a synthetic set of data is generated from scarce wind speed reanalysis data in order to achieve the increased sample size for the subsequent Monte Carlo simulation. In the presented case study, European wind power samples are generated from the modeled stochastic process. Under the precondition of a modeled perfect market environment, wind power impacts dispatch decisions and therefore leads to alterations in power balances. Stochastic power balances are implemented in a detailed model of the European electricity network, based on the generated samples. Finally, a Monte Carlo method is used to determine power flows and contingencies in the system. An indicator is elaborated in order to analyze risk of overloading and to prioritize necessary grid reinforcements. Implications for the Swiss power grid are investigated in detail, revealing that the current system is significantly put at risk in certain areas by the further integration of wind power in Europe. It is the first time that the results of a probabilistic model for wind energy are further deployed within a power system analysis of the interconnected European grid. The method presented in this paper allows to account for stochastic wind energy in a load flow analysis and to evaluate

77 FR 61597 - Avalon Wind, LLC; Avalon Wind 2, LLC; Catalina Solar, LLC; Catalina Solar 2, LLC; Pacific Wind...

Science.gov (United States)

2012-10-10

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. EL12-109-000] Avalon Wind, LLC; Avalon Wind 2, LLC; Catalina Solar, LLC; Catalina Solar 2, LLC; Pacific Wind Lessee, LLC; Pacific Wind 2, LLC; Valentine Solar, LLC; EDF Renewable Development, Inc.; Notice of Petition for Declaratory...

Trading wind generation from short-term probabilistic forecasts of wind power

DEFF Research Database (Denmark)

Pinson, Pierre; Chevallier, Christophe; Kariniotakis, Georges

2007-01-01

Due to the fluctuating nature of the wind resource, a wind power producer participating in a liberalized electricity market is subject to penalties related to regulation costs. Accurate forecasts of wind generation are therefore paramount for reducing such penalties and thus maximizing revenue......, as well as on modeling of the sensitivity a wind power producer may have to regulation costs. The benefits resulting from the application of these strategies are clearly demonstrated on the test case of the participation of a multi-MW wind farm in the Dutch electricity market over a year....... participation. Such strategies permit to further increase revenues and thus enhance competitiveness of wind generation compared to other forms of dispatchable generation. This paper formulates a general methodology for deriving optimal bidding strategies based on probabilistic forecasts of wind generation...

Wind power

Energy Technology Data Exchange (ETDEWEB)

1979-01-01

This publication describes some of the technical, economic, safety and institutional considerations involved in the selection, installation and evaluation of a wind generation system. This information is presented, where possible, in practical, non-technical terms. The first four sections provide background information, theory, and general knowledge, while the remaining six sections are of a more specific nature to assist the prospective owner of a wind generator in his calculations and selections. Meteorological information is provided relating to the wind regime in Nova Scotia. The section on cost analysis discusses some of the factors and considerations which must be examined in order to provide a logical comparison between the alternatives of electricity produced from other sources. The final two sections are brief summaries of the regulations and hazards pertaining to the use of wind generators. The cost of wind-generated electricity is high compared to present Nova Scotia Power Corporation rates, even on Sable Island, Nova Scotia's highest wind area. However, it may be observed that Sable Island is one of the areas of Nova Scotia which is not presently supplied through the power grid and, particularly if there was a significant increase in the price of diesel oil, wind-generated electricity may well be the most economical alternative in that area. Generally speaking, however, where a consumer can purchase electricity at the normal domestic rate, wind generators are not economical, and they will not become economical unless there is a great reduction in their cost, an great increase in electricity rates, or both. Includes glossary. 23 figs., 11 tabs.

Objective and subjective assessment of tonal components in noise from UK wind farm sites

International Nuclear Information System (INIS)

McKenzie, A.R.

1997-01-01

The level of any tonal components in the noise from a wind farm site can be quantified using objective analysis procedures. These procedures are, however, open to a certain amount of interpretation. an automated assessment procedure has, therefore, been developed which is appropriate to the needs of the wind turbine industry. This paper describes a study to compare the results of objective assessments carried out using this method with the results of carefully controlled subjective listening tests for samples of wind turbine noise from nine U.K. wind farm sites. (author)

Monthly Wind Characteristics and Wind Energy in Rwanda | Sarari ...

African Journals Online (AJOL)

Evaluating wind power potential for a site is indispensable before making any ... objective was to investigate the potential of wind energy resource in Rwanda. ... fit to the distribution of the measured wind data varies from a location to another. ... (14); Eritrea (1); Ethiopia (30); Ghana (27); Kenya (29); Lesotho (1); Libya (2) ...

Field measurement of wind pressure and wind-induced vibration of large-span spatial cable-truss system under strong wind or typhoon

Directory of Open Access Journals (Sweden)

ZHANG Zhihong

2013-10-01

Full Text Available In order to ensure wind-resistance safety of large-span pre-stressed flexible system in southeast coast area of China,and to prepare something for revising of current codes of practice or technical standards,the present paper conducts field measurement of wind pressure and wind-induced vibration of a practical and typical large-span spatial cable-truss system-lunar stadium in Yueqing city.Wind loading and wind effects on full-scale structure under strong wind or typhoon in real architectural environment can be obtained directly and effectively.Field measurement is the best way to investigate the wind loading property,wind effects,and wind-structure interactions of large-span flexible system.Measured data will be highly valuable for scientific research and practical design.On the other hand,it also provides the basis of wind-resistance safety design of this kind of tension structures.If any creative development,it would dramatically improve the research level of large-span pre-stressed flexible system in our country.

The Wind Energy programme - SFOE Research Programme 2000 - 2003; Programm Wind. Konzept BFE-Forschungsprogramm 'Wind' 2000 - 2003

Energy Technology Data Exchange (ETDEWEB)

Horbaty, R.

2001-07-01

This document, issued by the Swiss Federal Office of Energy (SFOE) describes the concept behind the Swiss wind energy programme. The first part of the report discusses the origins and development of the wind energy programme in Switzerland, discussing the importance of wind energy and policy matters associated with its promotion. The experience gained during the previous research programmes is reviewed. The degree to which targets were reached, promotional activities, the central government's own wind energy activities and the results of a programme evaluation are discussed. Lists of projects that have been realised and activities that have been carried out are presented and positive and negative influences on development are noted. A second part is dedicated to the goals of the wind energy programme in terms of target figures for the year 2010 and the strategies chosen to reach these goals, including pilot and demonstration projects (P and D) and promotional activities. Details of the P and D programme including lists of wind-power projects to be supported, the priorities that have been set and information and further education that is to be provided, are given. New activities in the wind power area such as the development of new type of wind turbine especially suited to alpine conditions are discussed. The role of the Swiss Association for Wind Energy 'Suisse Eole' as a network-partner in the wind energy programme is discussed. An appendix provides details of wind energy projects in Switzerland, market partners and customers. The results of a survey made of wind energy activities at Swiss institutes of higher education are presented.

Wind lens technology and its application to wind and water turbine and beyond

Directory of Open Access Journals (Sweden)

Ohya Yuji

2017-01-01

Full Text Available Wind lens is a new type of wind power system consisting of a simple brimmed ring structure that surrounds the rotor causing greater wind to pass through the turbine. As a consequence, the turbine's efficiency of capturing energy from the wind gets dramatically increased. A Wind lens turbine can generate 2–5 times the power of an existing wind turbine given at the same rotor diameter and incoming wind speed. This fluid dynamical effect is also effective in the water. We have developed 1–3 kW Wind lens turbines and a 100 kW Wind lens turbine. In addition to the enhanced output power, Wind lens turbine is quiet. The technology is now used in an offshore experiment with a hexagonal float 18 meters in diameter set off the coast of Hakata Bay in Fukuoka City. Moreover, we are now pursuing larger size Wind lens turbines through multi-rotor design consisting of multiple Wind lens turbines in a same vertical plane to embody larger total power output.

New England Wind Forum: A Wind Powering America Project, Newsletter #5 -- January 2010, Wind and Hydropower Technologies Program (WHTP)

Energy Technology Data Exchange (ETDEWEB)

Grace, R. C.; Gifford, J.

2010-01-01

Wind Powering America program launched the New England Wind Forum (NEWF) in 2005 to provide a single comprehensive source of up-to-date, Web-based information on a broad array of wind energy issues pertaining to New England. The NEWF newsletter provides New England stakeholders with updates on wind energy development in the region. In addition to regional updates, Issue #5 offers an interview with Angus King, former governor of Maine and co-founder of Independence Wind.

Wind energy in the agricultural sector. Tailwind or head wind?

International Nuclear Information System (INIS)

Van der Knijff, A.

1999-06-01

The state of the art in the use of wind energy in the agricultural sector in the Netherlands is given in order to map opportunities. Obstacles to expansion of wind capacity in that sector in the short term are described, as well as the most important developments with respect to wind energy. An estimated 275 wind turbines with a capacity of 50 MW are in use in the Netherlands. This means that the agricultural sector accounts for approximately 14% of the total wind capacity in the Netherlands (363 MW in 1998). Most of the agricultural businesses supply all the electricity generated to the public networks. Only a small number of farmers use some of the generated electricity themselves. The most important obstacles for the agrarian sector are the proposed policies of provinces and municipalities, the limited capacity of the public electricity network, and the lack of clarity regarding the liberalisation of the electricity market. In particular, provincial and municipal policies (solitary wind turbines versus wind farms) will determine the prospects for the future of wind energy in the agrarian sector. Despite possible adversities, there are good prospects for the future for the sector because farmers own land in windy locations. 33 refs

Wind turbines in your environment? Wind turbines and economic aspects

International Nuclear Information System (INIS)

2002-02-01

The wind energy industry has demonstrated its maturity and technical reliability. Because it will play an increasing role on the power generation market, the question of the cost and profitability of the wind energy has become of prime importance. Two main traps must be avoided: the first should be to deny the present and future economical interest of wind energy because of its supplementary cost with respect to conventional power generation techniques. The second trap should be to underestimate the economical progresses that wind energy must carry on to ensure its large scale development. Therefore, some advantageous pricing and regulatory conditions are necessary to allow the development of this emerging energy source. This document presents: the cost of a wind power project (initial investment, financial incentives); the profitability of a project (cost of a kWh of wind power origin, retail price, warranty of power supply capacity, indirect environmental costs, value of decentralized production); economical interest of wind power (energy efficiency, employment, financial advantages for the local economy); and who are the investors. (J.S.)

Evaluation of Mineral Deposits Along the Little Wind River, Riverton, WY, Processing Site

Energy Technology Data Exchange (ETDEWEB)

Campbell, Sam [Navarro Research and Engineering, Oak Ridge, TN (United States); Dam, Wiliam [US Department of Energy, Washington, DC (United States). Office of Legacy Management

2014-12-01

In 2012, the U.S.Department of Energy (DOE) began reassessing the former Riverton, Wyoming, Processing Site area for potential contaminant sources impacting groundwater. A flood in 2010 along the Little Wind River resulted in increases in groundwater contamination (DOE 2013).This investigation is a small part of continued efforts by DOE and other stakeholders to update human health and ecological risk assessments, to make a comprehensive examination of all exposure pathways to ensure that the site remains protective through established institutional controls. During field inspections at the Riverton Site in 2013, a white evaporitic mineral deposit was identified along the bank of the Little Wind River within the discharge zone of the groundwater contamination plume. In December 2013, Savannah River National Laboratory (SRNL) personnel collected a sample for analysis by X-ray fluorescence (Figure 1 shows the type of material sampled). The sample had a uranium concentration of approximately 64 to 73 parts per million. Although the uranium in this mineral deposit is within the expected range for evaporatic minerals in the western United States (SRNL 2014), DOE determined that additional assessment of the mineral deposit was warranted. In response to the initial collection and analysis of a sample of the mineral deposit, DOE developed a work plan (Work Plan to Sample Mineral Deposits Along the Little Wind River, Riverton, Wyoming, Processing Site [DOE 2014]) to further define the extent of these mineral deposits and the concentration of the associated contaminants (Appendix A). The work plan addressed field reconnaissance, mapping, sampling, and the assessment of risk associated with the mineral deposits adjacent to the Little Wind River.

EDITORIAL: Wind energy

Science.gov (United States)

Mann, Jakob; Nørkær Sørensen, Jens; Morthorst, Poul-Erik

2008-01-01

Wind energy is rapidly growing. In 2006 the installed generating capacity in the world increased by 25%, a growth rate which has more or less been sustained during the last decade. And there is no reason to believe that this growth will slow significantly in the coming years. For example, the United Kingdom's goal for installed wind turbines by 2020 is 33 GW up from 2 GW in 2006, an average annual growth rate of 22% over that period. More than half of all turbines are installed in Europe, but United States, India and lately China are also rapidly growing markets. The cradle of modern wind energy was set by innovative blacksmiths in rural Denmark. Now the wind provides more than 20% of the electrical power in Denmark, the industry has professionalized and has close ties with public research at universities. This focus issue is concerned with research in wind energy. The main purposes of research in wind energy are to: decrease the cost of power generated by the wind; increase the reliability and predictability of the energy source; investigate and reduce the adverse environmental impact of massive deployment of wind turbines; build research based educations for wind energy engineers. This focus issue contains contributions from several fields of research. Decreased costs cover a very wide range of activities from aerodynamics of the wind turbine blades, optimal site selection for the turbines, optimization of the electrical grid and power market for a fluctuating source, more efficient electrical generators and gears, and new materials and production techniques for turbine manufacturing. The United Kingdom recently started the construction of the London Array, a 1 GW off-shore wind farm east of London consisting of several hundred turbines. To design such a farm optimally it is necessary to understand the chaotic and very turbulent flow downwind from a turbine, which decreases the power production and increases the mechanical loads on other nearby turbines. Also

Offshore wind energy storage concept for cost-of-rated-power savings

International Nuclear Information System (INIS)

Qin, Chao; Saunders, Gordon; Loth, Eric

2017-01-01

Highlights: •Investigated CAES + HPT system concept for offshore wind energy; •Validated cost model for offshore wind farm including CAPEX and OPEX items; •Quantified cost-of-rated-power savings associated with CAES + HPT concept; •Estimated savings of 21.6% with CAES + HPT for a sample $2.92 billion project. -- Abstract: The size and number of off-shore wind turbines over the next decade is expected to rapidly increase due to the high wind energy potential and the ability of such farms to provide utility-scale energy. In this future, inexpensive and efficient on-site wind energy storage can be critical to address short-time (hourly) mismatches between wind supply and energy demand. This study investigates a compressed air energy storage (CAES) and hydraulic power transmission (HPT) system concept. To assess cost impact, the NREL Cost and Scaling Model was modified to improve accuracy and robustness for offshore wind farms with large turbines. Special attention was paid to the support structure, installation, electrical interface and connections, land leasing, and operations and maintenance cost items as well as specific increased/reduced costs reductions associated with CAES + HPT systems. This cost model was validated and applied to a sample $2.92 billion project Virginia Offshore case It was found that adaption of CAES + HPT can lead to a substantial savings of 21.6% of this 20-year lifetime cost by dramatically reducing capital and operating cost of the generator and power transmission components. However, there are several additional variables that can impact the off-shore energy policy and planning for this new CAES + HPT concept. Furthermore, these cost-savings are only first-order estimates based on linear mass-cost relationships, and thus detailed engineering and economic analysis are recommended.

Dynamic Models for Wind Turbines and Wind Power Plants

Energy Technology Data Exchange (ETDEWEB)

Singh, M.; Santoso, S.

2011-10-01

The primary objective of this report was to develop universal manufacturer-independent wind turbine and wind power plant models that can be shared, used, and improved without any restrictions by project developers, manufacturers, and engineers. Manufacturer-specific models of wind turbines are favored for use in wind power interconnection studies. While they are detailed and accurate, their usages are limited to the terms of the non-disclosure agreement, thus stifling model sharing. The primary objective of the work proposed is to develop universal manufacturer-independent wind power plant models that can be shared, used, and improved without any restrictions by project developers, manufacturers, and engineers. Each of these models includes representations of general turbine aerodynamics, the mechanical drive-train, and the electrical characteristics of the generator and converter, as well as the control systems typically used. To determine how realistic model performance is, the performance of one of the models (doubly-fed induction generator model) has been validated using real-world wind power plant data. This work also documents selected applications of these models.

Is the wind a periodical phenomenon? The case of Mexico

Energy Technology Data Exchange (ETDEWEB)

Hernandez-Escobedo, Quetzalcoatl [Gerencia de Energias No Convencionales, Instituto de Investigaciones Electricas. Reforma 113 Col. Palmira, C. P. 62490, Cuernavaca, Morelos (Mexico); Manzano-Agugliaro, Francisco; Zapata-Sierra, Antonio [Departamento de Ingenieria Rural, Universidad de Almeria, La Canada de San Urbano, 04120 Almeria (Spain); Gazquez-Parra, Jose Antonio [Departamento de Arquitectura de Computadores y Electronica, Universidad de Almeria, La Canada de San Urbano, 04120 Almeria (Spain)

2011-01-15

Under some author's opinion the wind is not a periodical phenomenon and therefore it is more reasonable to invest in renewable periodical energies as tides. In this paper we have developed a computer application based in MatLab {sup copyright}, that through the FFT (Fast Fourier Transform) analyzes the variations of wind speed amplitude in the time and frequency domain. The data were sampled every 10 min in the period 2000-2008. The data come from 31 Automatic Meteorological Stations (EMAs), the country of Mexico and correspond one per state. The survey shows the representation of spectral-temporal surfaces to long time intervals, as one year or more and denotes seasonal envelopes that alter the pattern at certain times everyday. As a conclusion, the wind has an important periodical component for the country of Mexico, since the fundamental component of the wind speed represents a frequency of 1/24 h{sup -1} in a very accurate form throughout the time studied. To harness the wind potential of the country of Mexico it should be kept in mind that there is a minimum wind speed between 8 and 16 h and a maximum close to 24 h. (author)

Aggregated wind power plant models consisting of IEC wind turbine models

DEFF Research Database (Denmark)

Altin, Müfit; Göksu, Ömer; Hansen, Anca Daniela

2015-01-01

The common practice regarding the modelling of large generation components has been to make use of models representing the performance of the individual components with a required level of accuracy and details. Owing to the rapid increase of wind power plants comprising large number of wind...... turbines, parameters and models to represent each individual wind turbine in detail makes it necessary to develop aggregated wind power plant models considering the simulation time for power system stability studies. In this paper, aggregated wind power plant models consisting of the IEC 61400-27 variable...... speed wind turbine models (type 3 and type 4) with a power plant controller is presented. The performance of the detailed benchmark wind power plant model and the aggregated model are compared by means of simulations for the specified test cases. Consequently, the results are summarized and discussed...

Advanced structural wind engineering

CERN Document Server

Kareem, Ahsan

2013-01-01

This book serves as a textbook for advanced courses as it introduces state-of-the-art information and the latest research results on diverse problems in the structural wind engineering field. The topics include wind climates, design wind speed estimation, bluff body aerodynamics and applications, wind-induced building responses, wind, gust factor approach, wind loads on components and cladding, debris impacts, wind loading codes and standards, computational tools and computational fluid dynamics techniques, habitability to building vibrations, damping in buildings, and suppression of wind-induced vibrations. Graduate students and expert engineers will find the book especially interesting and relevant to their research and work.

Assessment of Wind Parameter Sensitivity on Extreme and Fatigue Wind Turbine Loads

Energy Technology Data Exchange (ETDEWEB)

Robertson, Amy N [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Sethuraman, Latha [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jonkman, Jason [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Quick, Julian [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2018-01-12

Wind turbines are designed using a set of simulations to ascertain the structural loads that the turbine could encounter. While mean hub-height wind speed is considered to vary, other wind parameters such as turbulence spectra, sheer, veer, spatial coherence, and component correlation are fixed or conditional values that, in reality, could have different characteristics at different sites and have a significant effect on the resulting loads. This paper therefore seeks to assess the sensitivity of different wind parameters on the resulting ultimate and fatigue loads on the turbine during normal operational conditions. Eighteen different wind parameters are screened using an Elementary Effects approach with radial points. As expected, the results show a high sensitivity of the loads to the turbulence standard deviation in the primary wind direction, but the sensitivity to wind shear is often much greater. To a lesser extent, other wind parameters that drive loads include the coherence in the primary wind direction and veer.

Wind speed reductions by large-scale wind turbine deployments lower turbine efficiencies and set low wind power potentials

Science.gov (United States)

Miller, Lee; Kleidon, Axel

2017-04-01

Wind turbines generate electricity by removing kinetic energy from the atmosphere. Large numbers of wind turbines are likely to reduce wind speeds, which lowers estimates of electricity generation from what would be presumed from unaffected conditions. Here, we test how well wind power potentials that account for this effect can be estimated without explicitly simulating atmospheric dynamics. We first use simulations with an atmospheric general circulation model (GCM) that explicitly simulates the effects of wind turbines to derive wind power limits (GCM estimate), and compare them to a simple approach derived from the climatological conditions without turbines [vertical kinetic energy (VKE) estimate]. On land, we find strong agreement between the VKE and GCM estimates with respect to electricity generation rates (0.32 and 0.37 We m-2) and wind speed reductions by 42 and 44%. Over ocean, the GCM estimate is about twice the VKE estimate (0.59 and 0.29 We m-2) and yet with comparable wind speed reductions (50 and 42%). We then show that this bias can be corrected by modifying the downward momentum flux to the surface. Thus, large-scale limits to wind power can be derived from climatological conditions without explicitly simulating atmospheric dynamics. Consistent with the GCM simulations, the approach estimates that only comparatively few land areas are suitable to generate more than 1 We m-2 of electricity and that larger deployment scales are likely to reduce the expected electricity generation rate of each turbine. We conclude that these atmospheric effects are relevant for planning the future expansion of wind power.

WIND EROSION INTENSITY DETERMINATION USING SOIL PARTICLE CATCHER DEVICES

Directory of Open Access Journals (Sweden)

Lenka Lackóová

2013-12-01

Full Text Available To analyze wind erosion events in the real terrain conditions, we proposed to construct a prototype of soil particle catcher devices to trap soil particles. With these devices we are able to measure the intensity of wind erosion at six different heights above the soil surface in one location or at three different heights in two places. It is possible to use them for six different places at the same time as well. We performed field measurements to determine the amount of soil particles transported by the wind between 26th – 31st March 2012. Each measuring took 60 minutes. After this time the soil particle catchers were emptied and further measurements carried out. At the beginning we selected two places for measurement (soil HPJ 16 and 37 at two heights, one above the other. Then we used two measuring systems 40 m apart at two sites (D2 and D4 and the soil captured at two heights (0, 1. The maximum weight of soil particles trapped in measuring system D2 at height (0 was 1242.7 g at a wind speed of 9.6 ms-1. At measurement height (1 the maximum weight was 72.7 g trapped at the same average hourly rate, but during different measurement events. The measuring system at D4 trapped the highest amount of soil at a wind speed of 8.9 ms-1 (1141.7 g at height (0 and at a speed of 9.3 ms-1 (22.3 g at height (1. During the measurements with the two basic measuring systems D4 and D2, we measured the wind erosion intensity together with soil particle catchers D1 and D3. D3 was placed between devices D4 and D2, D1 was 20 m ahead D2. Soil particle catchers were placed on the soil surface at height position (0. We measured increasing soil erosion downwind on four locations spaced at 20 m. The results show that with there is an increasing quantity of particles collected as the erosive surface length increases, due to the so-called snowball effect. We analyzed selected trapped soil samples in order to determine the size of the soil particles and their proportion

Spatial dependence in wind and optimal wind power allocation: A copula-based analysis

International Nuclear Information System (INIS)

Grothe, Oliver; Schnieders, Julius

2011-01-01

The investment decision on the placement of wind turbines is, neglecting legal formalities, mainly driven by the aim to maximize the expected annual energy production of single turbines. The result is a concentration of wind farms at locations with high average wind speed. While this strategy may be optimal for single investors maximizing their own return on investment, the resulting overall allocation of wind turbines may be unfavorable for energy suppliers and the economy because of large fluctuations in the overall wind power output. This paper investigates to what extent optimal allocation of wind farms in Germany can reduce these fluctuations. We analyze stochastic dependencies of wind speed for a large data set of German on- and offshore weather stations and find that these dependencies turn out to be highly nonlinear but constant over time. Using copula theory we determine the value at risk of energy production for given allocation sets of wind farms and derive optimal allocation plans. We find that the optimized allocation of wind farms may substantially stabilize the overall wind energy supply on daily as well as hourly frequency. - Highlights: → Spatial modeling of wind forces in Germany. → A novel way to assess nonlinear dependencies of wind forces by copulas. → Wind turbine allocation by maximizing lower quantiles of energy production. → Optimal results show major increase in reliable part of wind energy.

Wind power plant

Energy Technology Data Exchange (ETDEWEB)

Weiss, G

1975-11-20

A wind power plant is proposed suitable for electicity generation or water pumping. This plant is to be self-adjusting to various wind velocities and to be kept in operation even during violent storms. For this purpose the mast, carrying the wind rotor and pivotable around a horizontal axis is tiltable and equipped with a wind blind. Further claims contain various configurations of the tilting base resp. the cut in of an elastic link, the attachment and design of the wind blind as well as the constructive arrangement of one or more dynamos.

Second wind in the offshore wind industry

International Nuclear Information System (INIS)

Philippe, Edouard; Neyme, Eric; Deboos, Christophe; Villageois, Jean-Remy; Gouverneur, Philippe; Gerard, Bernard; Fournier, Eric; Petrus, Raymond; Lemarquis, David; Dener, Marc; Bivaud, Jean-Pierre; Lemaire, Etienne; Nielsen, Steffen; Lafon, Xavier; Lagandre, Pierre; Nadai, Alain; Pinot de Villechenon, Edouard; Westhues, Markus; Herpers, Frederick; Bisiaux, Christophe; Sperlich, Miriam; Bales, Vincent; Vandenbroeck, Jan; His, Stephane; Derrey, Thierry; Barakat, Georges; Dakyo, Brayima; Carme, Laurent; Petit, Frederic; Ytournel, Sophie; Westhues, Markus; Diller, Armin; Premont, Antoine de; Ruer, Jacques; Lanoe, Frederic; Declercq, Jan; Holmager, Morten; Fidelin, Daniel; Guillet, Jerome; Dudziak, Gregory; Lapierre, Anne; Couturier, Ludovic; Audineau, Jean-Pierre; Rouaix, Eric; De Roeck, Yann-Herve; Quesnel, Louis; Duguet, Benjamin

2011-06-01

After several keynote addresses, this publication contains contributions and Power Point presentations proposed during this conference on the development of offshore wind energy. The successive sessions addressed the following issues: the offshore mass production of electricity (examples of Denmark and Belgium, laying and protecting offshore cables), the space, economic and environmental planning (the Danish experience, the role of the Coastal area integrated management, importance of the public debate, so on), the logistics of port infrastructures (simulation tools, example of Bremerhaven, issues related to project management), innovation at the core of industrial strategies (high power wind turbines, the 6 MW Alstom turbine, chain value and innovation in offshore wind energy, the Vertiwing innovating project of a floating wind turbine, a bench test in Charleston, foundations, gravity base structures, the British experience, the Danish experience), the economic and organisational conditions for development, the validation and certification of technologies

SimWIND: A geospatial infrastructure model for optimizing wind power generation and transmission

International Nuclear Information System (INIS)

Phillips, Benjamin R.; Middleton, Richard S.

2012-01-01

Wind is a clean, enduring energy resource with the capacity to satisfy 20% or more of U.S. electricity demand. Presently, wind potential is limited by a paucity of electrical transmission lines and/or capacity between promising wind resources and primary load centers. We present the model SimWIND to address this shortfall. SimWIND is an integrated optimization model for the geospatial arrangement and cost minimization of wind-power generation–transmission–delivery infrastructure. Given a set of possible wind-farm sites, the model simultaneously determines (1) where and how much power to generate and (2) where to build new transmission infrastructure and with what capacity in order to minimize the cost for delivering a targeted amount of power to load. Costs and routing of transmission lines consider geographic and social constraints as well as electricity losses. We apply our model to the Electric Reliability Council of Texas (ERCOT) Interconnection, considering scenarios that deliver up to 20 GW of new wind power. We show that SimWIND could potentially reduce ERCOT's projected ∼$5B transmission network upgrade line length and associated costs by 50%. These results suggest that SimWIND's coupled generation–transmission–delivery modeling approach could play a critical role in enhancing planning efforts and reducing costs for wind energy integration. - Highlights: ► Wind power is limited by transmission capacity between resources and demands. ► SimWIND is a coupled generation-transmission-delivery model for wind infrastructure. ► The model minimizes costs considering realistic transmission routing and networking. ► We show that SimWIND could save 50% of $5B costs for expanding the Texas grid. ► Results suggest SimWIND may play a critical role in enhancings wind planning efforts.

Remoção e concentração de urânio de rejeito de mina

Directory of Open Access Journals (Sweden)

Elizângela Augusta Santos

2011-01-01

Full Text Available A utilização de agentes lixiviantes como citrato de sódio e carbonato de amônio foram estudados para a recuperação de urânio (U de um rejeito de mina. Técnicas de concentração como precipitação e troca iônica foram avaliadas. O rejeito estudado apresenta 0,25% de U. Resultados mostraram extração máxima de aproximadamente 40% para ambos os reagentes. 62% de U foram precipitados do licor da lixiviação empregando-se solução a 10 mol L-1 de NaOH. Os carregamentos máximos do metal obtidos a pH 3,9 apontaram uma maior capacidade de remoção empregando-se a resina IRA 910 U cujo valor de carregamento máximo foi de 126,9 mg g-1 e de 148,3 mg g-1 para a DOWEX RPU.Abstract The use of leaching agents, such as sodium citrateand ammonium carbonate, were assessed for the extraction ofuranium from one mining residue containing 0.25% U.Concentration techniques such as precipitation and ion exchangewere employed to recover the uranium from the leaching liquor.Leaching results showed maximum uranium extraction of about 40% for both reagents. The use 10 mol L-1 NaOH to precipitatethe uranium from the leach liquor leads to a recovery of 62%;what was considered not satisfactory. In view of this, resins wereused to concentrate the uranium from the liquor and the metalloading obtained at pH 3.9 was higher for the resin DOWEXRPU, whose maximum loading maximum capacity was148,3 mg g-1, compared to 126,9 mg g-1 presented by the resinIRA 910 U.

Wind energy potential of coastal Eritrea: an analysis of sparse wind data

International Nuclear Information System (INIS)

Rosen, K.; Buskirk, R. van; Garbesi, K.

1999-01-01

This paper describes an analysis of historical surface wind data for the small country of Eritrea, in northeastern Africa. Winds in this region are directed by summer and winter monsoons in addition to diurnal land-sea effects. An analysis of national Eritrean and historical Italian wind records indicated marginal wind resources in the central highlands near the Eritrean capital of Asmera. An analysis of wind speed records recorded at two sites in the southern port city of Aseb indicate mean annual 10-m wind speeds of 9.5 m s -1 at the windier site. Surface wind speed records for the Red Sea suggest that similar potential may be found along the lower 200 km of the Eritrean coastline. Based on these findings, wind-generated electricity in this region should be substantially cheaper than the current supply generated from imported diesel. (author)

Wind energy.

Science.gov (United States)

Leithead, W E

2007-04-15

From its rebirth in the early 1980s, the rate of development of wind energy has been dramatic. Today, other than hydropower, it is the most important of the renewable sources of power. The UK Government and the EU Commission have adopted targets for renewable energy generation of 10 and 12% of consumption, respectively. Much of this, by necessity, must be met by wind energy. The US Department of Energy has set a goal of 6% of electricity supply from wind energy by 2020. For this potential to be fully realized, several aspects, related to public acceptance, and technical issues, related to the expected increase in penetration on the electricity network and the current drive towards larger wind turbines, need to be resolved. Nevertheless, these challenges will be met and wind energy will, very likely, become increasingly important over the next two decades. An overview of the technology is presented.

An optimization approach for wind turbine commitment and dispatch in a wind park

Energy Technology Data Exchange (ETDEWEB)

Moyano, Carlos F. [School of Engineering Systems, Faculty of Built Environment and Engineering, Queensland University of Technology, GPO Box 2434, Brisbane, QLD 4001 (Australia); Pecas Lopes, Joao A. [Instituto de Engenharia de Sistemas e Computadores do Porto (Portugal); Faculdade de Engenharia da Universidade do Porto, Campus da FEUP, Rua Dr. Roberto Frias, 378 4200-465 Porto (Portugal)

2009-01-15

This paper describes an operational optimization strategy to be adopted at the wind park control level, that enables defining the commitment of wind turbines and their active and reactive power outputs following requests from Wind Park Dispatch Centers, assuming that individual wind turbines short-term wind speed forecasts are known and are expressed as power availability. This operational strategy was also developed with a concern on the minimization of the connection/disconnection changes of the individual wind generators, for a given time horizon. When identifying the active/reactive dispatching policies, wind generators loading capabilities are also taken in account. This optimization tool is especially suited to manage large wind parks. (author)

Wind resource assessment and wind energy system cost analysis: Fort Huachuca, Arizona

Energy Technology Data Exchange (ETDEWEB)

Olsen, T.L. [Tim Olsen Consulting, Denver, CO (United States); McKenna, E. [National Renewable Energy Lab., Golden, CO (United States)

1997-12-01

The objective of this joint DOE and National Renewable Energy Laboratory (NREL) Strategic Environmental Research and Development Program (SERDP) project is to determine whether wind turbines can reduce costs by providing power to US military facilities in high wind areas. In support of this objective, one year of data on the wind resources at several Fort Huachuca sites was collected. The wind resource data were analyzed and used as input to an economic study for a wind energy installation at Fort Huachuca. The results of this wind energy feasibility study are presented in the report.

Thermal loading of wind power converter considering dynamics of wind speed

DEFF Research Database (Denmark)

Baygildina, Elvira; Peltoniemi, Pasi; Pyrhönen, Olli

2013-01-01

The thermal loading of power semiconductors is a crucial performance related to the reliability and cost of the wind power converter. However, the thermal loading impacts by the variation of wind speeds have not yet been clarified, especially when considering the aerodynamic behavior of the wind...... turbines. In this paper, the junction temperatures in the wind power converter are studied under not only steady state, but also turbulent wind speed conditions. The study is based on a 1.5 MW direct-driven turbine system with aerodynamic model described by Unsteady Blade Element Momentum Method (BEMM......), and the thermal stress of power devices is investigated from the frequency spectrum point of view of wind speed. It is concluded that because of the strong inertia effects by the aerodynamic behavior of wind turbines, thermal stress of the semiconductors is relatively more stable and only influenced by the low...

New methods for sampling sparse populations

Science.gov (United States)

Anna Ringvall

2007-01-01

To improve surveys of sparse objects, methods that use auxiliary information have been suggested. Guided transect sampling uses prior information, e.g., from aerial photographs, for the layout of survey strips. Instead of being laid out straight, the strips will wind between potentially more interesting areas. 3P sampling (probability proportional to prediction) uses...

Wind Atlas for Egypt

DEFF Research Database (Denmark)

The results of a comprehensive, 8-year wind resource assessment programme in Egypt are presented. The objective has been to provide reliable and accurate wind atlas data sets for evaluating the potential wind power output from large electricityproducing wind turbine installations. The regional wind...... climates of Egypt have been determined by two independent methods: a traditional wind atlas based on observations from more than 30 stations all over Egypt, and a numerical wind atlas based on long-term reanalysis data and a mesoscale model (KAMM). The mean absolute error comparing the two methods is about...... 10% for two large-scale KAMM domains covering all of Egypt, and typically about 5% for several smaller-scale regional domains. The numerical wind atlas covers all of Egypt, whereas the meteorological stations are concentrated in six regions. The Wind Atlas for Egypt represents a significant step...

Wind Atlas for Egypt

DEFF Research Database (Denmark)

Mortensen, Niels Gylling; Said Said, Usama; Badger, Jake

2006-01-01

The results of a comprehensive, 8-year wind resource assessment programme in Egypt are presented. The objective has been to provide reliable and accurate wind atlas data sets for evaluating the potential wind power output from large electricityproducing wind turbine installations. The regional wind...... climates of Egypt have been determined by two independent methods: a traditional wind atlas based on observations from more than 30 stations all over Egypt, and a numerical wind atlas based on long-term reanalysis data and a mesoscale model (KAMM). The mean absolute error comparing the two methods is about...... 10% for two large-scale KAMM domains covering all of Egypt, and typically about 5% for several smaller-scale regional domains. The numerical wind atlas covers all of Egypt, whereas the meteorological stations are concentrated in six regions. The Wind Atlas for Egypt represents a significant step...

Wind Tunnel Measurements at LM Wind Power

DEFF Research Database (Denmark)

Bertagnolio, Franck

2012-01-01

This section presents the results obtained during the experimental campaign that was conducted in the wind tunnel at LM Wind Power in Lunderskov from August 16th to 26th, 2010. The goal of this study is to validate the so-called TNO trailing edge noise model through measurements of the boundary...... layer turbulence characteristics and the far-field noise generated by the acoustic scattering of the turbulent boundary layer vorticies as they convect past the trailing edge. This campaign was conducted with a NACA0015 airfoil section that was placed in the wind tunnel section. It is equipped with high...

Wind energy expo '82 and national conference American Wind Energy Association

Energy Technology Data Exchange (ETDEWEB)

Nelson, V. (ed.)

1982-01-01

Separate abstracts were prepared for 41 papers in this conference report. Wind farms, large wind turbines, new wind turbines, marketing small wind systems, programs, performance, and economics, analytic methods, testing, power conversion, and rotor systems are the principal topics covered.

Environmental impacts of wind power. Case study of wind turbines in living environment; Vindkraftens Miljoepaaverkan. Fallstudie av vindkraftverk i boendemiljoe

Energy Technology Data Exchange (ETDEWEB)

Widing, Angelica; Britse, Gunilla; Wizelius, Tore [Gotland Univ., Visby (Sweden). Windpower information centre

2006-06-15

The aim of this project has been to get more knowledge about the impact of noise, shadows and on the view of the landscape from wind turbines. Further to be able to increase the reliability and relevance of the methods used to calculate and evaluate nuisances from wind turbines in applications for wind power development. We have also tried to find other factors that can play a role for the evaluation of wind turbines, if they will be considered as a nuisance or not. The research has focused on a critical review of the methods and regulations that are used in Sweden and other countries, and case studies to find out how people living neighbors with wind turbines will be affected by noise, rotating shadows, visual intrusion and other factors. This report includes the case studies of wind turbine areas at Gotland. Three different areas on the island Gotland in the Baltic Sea, with wind turbines in the close neighborhood, were chosen for case studies: Naer, Klintehamn, Naesudden. In these places only persons who live close to wind turbines have been interviewed; in Nar all who live within 1100 meters from two large wind turbines, in Klintehamn a sample of those who live ESE of the turbines and get shadow flicker from them during sunset, and on Naesudden those households that live in the middle of a large wind farm with 81 turbines. In total 94 persons in 69 households have been interviewed. The acceptance of wind power among people living as close neighbors is quite high. However, the nuisance and annoyance can be reduced further, if the recommended values for noise immission etc are applied correctly. To do that the ability of project developers and authorities that grant permissions to evaluate the calculated immission has to be raised, since specialist competence and experience is necessary to do predictions of actual immission from the models used for calculations. The recommended minimum distances between wind turbines and houses that some communities have

Contribution of Strong Discontinuities to the Power Spectrum of the Solar Wind

International Nuclear Information System (INIS)

Borovsky, Joseph E.

2010-01-01

Eight and a half years of magnetic field measurements (2 22 samples) from the ACE spacecraft in the solar wind at 1 A.U. are analyzed. Strong (large-rotation-angle) discontinuities in the solar wind are collected and measured. An artificial time series is created that preserves the timing and amplitudes of the discontinuities. The power spectral density of the discontinuity series is calculated and compared with the power spectral density of the solar-wind magnetic field. The strong discontinuities produce a power-law spectrum in the ''inertial subrange'' with a spectral index near the Kolmogorov -5/3 index. The discontinuity spectrum contains about half of the power of the full solar-wind magnetic field over this ''inertial subrange.'' Warnings are issued about the significant contribution of discontinuities to the spectrum of the solar wind, complicating interpretation of spectral power and spectral indices.

Wind Energy Basics | NREL

Science.gov (United States)

Wind Energy Basics Wind Energy Basics We have been harnessing the wind's energy for hundreds of grinding grain. Today, the windmill's modern equivalent-a wind turbine can use the wind's energy to most energy. At 100 feet (30 meters) or more aboveground, they can take advantage of the faster and

Wind model for low frequency power fluctuations in offshore wind farms

DEFF Research Database (Denmark)

Vigueras-Rodríguez, A.; Sørensen, Poul Ejnar; Cutululis, Nicolaos Antonio

2010-01-01

of hours, taking into account the spectral correlation between different wind turbines. The modelling is supported by measurements from two large wind farms, namely Nysted and Horns Rev. Measurements from individual wind turbines and meteorological masts are used. Finally, the models are integrated......This paper investigates the correlation between the frequency components of the wind speed Power Spectral Density. The results extend an already existing power fluctuation model that can simulate power fluctuations of wind power on areas up to several kilometers and for time scales up to a couple...

Comparative study of the behavior of wind-turbines in a wind farm

Energy Technology Data Exchange (ETDEWEB)

Migoya, Emilio; Crespo, Antonio; Garcia, Javier; Manuel, Fernando; Jimenez, Angel [Universidad Politecnica de Madrid (UPM), Madrid (Spain). Departamento de Ingenieria Energetica y Fluidomecanica, Laboratorio de Mecanica de Fluidos; Moreno, Fermin [Comision Nacional de la Energia, Madrid (Spain); Costa, Alexandre [Energia Eolica, Division de Energias Renovables, CIEMAT, Madrid (Spain)

2007-10-15

The Sotavento wind farm is an experimental wind farm which has different types of wind turbines. It is located in an area whose topography is moderately complex, and where wake effects can be significant. One of the objectives of Sotavento wind farm is to compare the performances of the different machines; particularly regarding power production, maintenance and failures. However, because of wakes and topography, the different machines are not working under identical conditions. Two linearized codes have been used to estimate topography effects: UPMORO and WAsP. For wind directions in which topography is abrupt, the non-linear flow equations have been solved with the commercial code FLUENT, although the results are only qualitatively used. For wake effects, the UPMPARK code has been applied. As a result, the incident velocity over each wind turbine is obtained, and the power production is estimated by means of the power curve of each machine. Experimental measurements give simultaneously the wind characteristics at the measuring stations, the wind velocity, at the nacelle anemometer, and the power production of each wind turbine. These experimental results are employed to validate the numerical predictions. The main objective of this work is to deduce and validate a relationship between the wind characteristics measured in the anemometers and the wind velocity and the power output in each machine. (author)

LIDAR wind speed measurements from a rotating spinner (SpinnerEx 2009)

Energy Technology Data Exchange (ETDEWEB)

Angelou, N.; Mikkelsen, Torben; Hansen, Kasper H.; Sjoeholm, M.; Harris, M.

2010-08-15

In the context of the increasing application of remote sensing techniques in wind energy, the feasibility of upwind observations via a spinner-mounted wind lidar was tested during the SpinnerEx 2009 experiment. The objective was to install a QinetiQ (Natural Power) ZephIR lidar in the rotating spinner of a MW-sized wind turbine, and investigate the approaching wind fields from this vantage point. Time series of wind speed measurements from the lidar with 50 Hz sampling rate were successfully obtained for approximately 60 days, during the measurement campaign lasting from April to August 2009. In this report, information is given regarding the experimental setup and the lidar's operation parameters. The geometrical model used for the reconstruction of the scanning pattern of the lidar is described. This model takes into account the lidar's pointing direction, the spinner axis's vertical tilt and the wind turbine's yaw relative to the mean wind speed direction. The data analysis processes are documented. A methodology for the calculation of the yaw misalignment of the wind turbine relative to the wind direction, as a function of various averaging times, is proposed, using the lidar's instantaneous line-of-sight radial wind speed measurements. Two different setups have been investigated in which the approaching wind field was measured at distances of 0.58 OE and 1.24 OE rotor diameters upwind, respectively. For both setups, the instantaneous yaw misalignment of the turbine has been estimated from the lidar measurements. Data from an adjacent meteorological mast as well as data logged within the wind turbine's control system were used to evaluate the results. (author)

Wind lens technology and its application to wind and water turbine and beyond

OpenAIRE

Ohya Yuji; Karasudani Takashi; Nagai Tomoyuki; Watanabe Koichi

2017-01-01

Wind lens is a new type of wind power system consisting of a simple brimmed ring structure that surrounds the rotor causing greater wind to pass through the turbine. As a consequence, the turbine's efficiency of capturing energy from the wind gets dramatically increased. A Wind lens turbine can generate 2–5 times the power of an existing wind turbine given at the same rotor diameter and incoming wind speed. This fluid dynamical effect is also effective in the water. We have developed 1–3 kW W...

Performance assessment of Portuguese wind farms: Ownership and managerial efficiency

International Nuclear Information System (INIS)

Pestana Barros, Carlos; Sequeira Antunes, Olinda

2011-01-01

This paper analyzes ownership and unobserved managerial ability as factors affecting the performance of a representative sample of Portuguese wind farms by means of frontier models. These farms are ranked according to their technical efficiency during the period 2004-2008 and homogenous and heterogeneous variables are disentangled in the cost function, which leads us to advise the implementation of common policies as well as policies by segments. Economic implications arising from the study are also considered. - Research highlights: → Wind farms are heterogeneous displaying distinct ownership and managerial characteristics that affect efficiency. → Managerial practices has a positive impact on the efficiency. → Ownership has a positive impact on the efficiency. Large wind farms are more efficient.

Wind energy systems

International Nuclear Information System (INIS)

Richardson, R.D.; McNerney, G.M.

1993-01-01

Wind energy has matured to a level of development where it is ready to become a generally accepted utility generation technology. A brief discussion of this development is presented, and the operating and design principles are discussed. Alternative designs for wind turbines and the tradeoffs that must be considered are briefly compared. Development of a wind energy system and the impacts on the utility network including frequency stability, voltage stability, and power quality are discussed. The assessment of wind power station economics and the key economic factors that determine the economic viability of a wind power plant are presented

Forecasting wind power production from a wind farm using the RAMS model

DEFF Research Database (Denmark)

Tiriolo, L.; Torcasio, R. C.; Montesanti, S.

2015-01-01

of the ECMWF Integrated Forecasting System (IFS), whose horizontal resolution over Central Italy is about 25 km at the time considered in this paper. Because wind observations were not available for the site, the power curve for the whole wind farm was derived from the ECMWF wind operational analyses available......The importance of wind power forecast is commonly recognized because it represents a useful tool for grid integration and facilitates the energy trading. This work considers an example of power forecast for a wind farm in the Apennines in Central Italy. The orography around the site is complex...... and the horizontal resolution of the wind forecast has an important role. To explore this point we compared the performance of two 48 h wind power forecasts using the winds predicted by the Regional Atmospheric Modeling System (RAMS) for the year 2011. The two forecasts differ only for the horizontal resolution...

Economic performance indicators of wind energy based on wind speed stochastic modeling

International Nuclear Information System (INIS)

D’Amico, Guglielmo; Petroni, Filippo; Prattico, Flavio

2015-01-01

Highlights: • We propose a new and different wind energy production indicator. • We compute financial profitability of potential wind power sites. • The wind speed process is modeled as an indexed semi-Markov chain. • We check if the wind energy is a good investment with and without incentives. - Abstract: We propose the computation of different wind energy production indicators and financial profitability of potential wind power sites. The computation is performed by modeling the wind speed process as an indexed semi-Markov chain to predict and simulate the wind speed dynamics. We demonstrate that the indexed semi-Markov chain approach enables reproducing the indicators calculated on real data. Two different time horizons of 15 and 30 years are analyzed. In the first case we consider the government incentives on the energy price now present in Italy, while in the second case the incentives have not been taken into account

Wind resources at turbine height from Envisat and Sentinel-1 SAR

DEFF Research Database (Denmark)

Badger, Merete; Hasager, Charlotte Bay; Pena Diaz, Alfredo

for the standard output level of 10 m above the sea surface. This presentation demonstrates the effects of two recent improvements related to satellite-based wind resource mapping: 1) The number of satellite samples has increased dramatically since the launch of Sentinel-1A/B 2) A new method looks promising...... National Ice Center. Once the instantaneous wind maps are stored in our database, they can be organized as time series in order to calculate wind resources for any point location or area. Since the time series comprises data from both Envisat and Sentinel-1, a check of the data calibration against one....... To extrapolate the 10-m wind resource maps from SAR to higher levels within the atmospheric boundary layer, we estimate a wind profile for each grid cell in the maps. Simulations from the Weather Research and Forecasting (WRF) model are used to correct this profile for long-term atmospheric stability effects...

Wind Tunnel Modeling Of Wind Flow Over Complex Terrain

Science.gov (United States)

Banks, D.; Cochran, B.

2010-12-01

This presentation will describe the finding of an atmospheric boundary layer (ABL) wind tunnel study conducted as part of the Bolund Experiment. This experiment was sponsored by Risø DTU (National Laboratory for Sustainable Energy, Technical University of Denmark) during the fall of 2009 to enable a blind comparison of various air flow models in an attempt to validate their performance in predicting airflow over complex terrain. Bohlund hill sits 12 m above the water level at the end of a narrow isthmus. The island features a steep escarpment on one side, over which the airflow can be expected to separate. The island was equipped with several anemometer towers, and the approach flow over the water was well characterized. This study was one of only two only physical model studies included in the blind model comparison, the other being a water plume study. The remainder were computational fluid dynamics (CFD) simulations, including both RANS and LES. Physical modeling of air flow over topographical features has been used since the middle of the 20th century, and the methods required are well understood and well documented. Several books have been written describing how to properly perform ABL wind tunnel studies, including ASCE manual of engineering practice 67. Boundary layer wind tunnel tests are the only modelling method deemed acceptable in ASCE 7-10, the most recent edition of the American Society of Civil Engineers standard that provides wind loads for buildings and other structures for buildings codes across the US. Since the 1970’s, most tall structures undergo testing in a boundary layer wind tunnel to accurately determine the wind induced loading. When compared to CFD, the US EPA considers a properly executed wind tunnel study to be equivalent to a CFD model with infinitesimal grid resolution and near infinite memory. One key reason for this widespread acceptance is that properly executed ABL wind tunnel studies will accurately simulate flow separation

Wind farm economics

International Nuclear Information System (INIS)

Milborrow, D.J.

1995-01-01

The economics of wind energy are changing rapidly, with improvements in machine performance and increases in size both contributing to reduce costs. These trends are examined and future costs assessed. Although the United Kingdom has regions of high wind speed, these are often in difficult terrain and construction costs are often higher than elsewhere in Europe. Nevertheless, wind energy costs are converging with those of the conventional thermal sources. At present, bank loan periods for wind projects are shorter than for thermal plant, which means that energy prices are higher. Ways of overcoming this problem are explored. It is important, also, to examine the value of wind energy. It is argued that wind energy has a higher value than energy from centralized plant, since it is fed into the low-voltage distribution network. (Author)

Reading interests and use of library resources by students in ...

African Journals Online (AJOL)

This study investigated the reading interest and use of school library resources in selected secondary schools in Ijebu-Remo zone of Ogun- State. Survey research design was adopted, while random sampling technique was used to sample 330 students from the five schools surveyed. A self-designed questionnaire was ...

Superconducting Wind Turbine Generators

Directory of Open Access Journals (Sweden)

Yunying Pan

2016-08-01

Full Text Available Wind energy is well known as a renewable energy because its clean and less polluted characteristic, which is the foundation of development modern wind electricity. To find more efficient wind turbine is the focus of scientists around the world. Compared from conventional wind turbines, superconducting wind turbine generators have advantages at zero resistance, smaller size and lighter weight. Superconducting wind turbine will inevitably become the main trends in this area. This paper intends to introduce the basic concept and principle of superconductivity, and compare form traditional wind turbine to obtain superiority, then to summary three proposed machine concept.While superconductivity have difficulty  in modern technology and we also have proposed some challenges in achieving superconducting wind turbine finally.

Influência do estrógeno (17B-estradiol) no osso alveolar e na movimentação dentária em ratas, após remoção do aparelho ortodôntico

OpenAIRE

Park, Danielle Morello [UNESP

2004-01-01

A reabsorção óssea é um fator limitante que determina o grau de movimentação dentária induzida ortodonticamente. Vários hormônios, dentre os quais os estrógenos desempenham importante papel no equilíbrio entre formação e reabsorção óssea. Embora alguns trabalhos demonstrem relação direta entre os estrógenos e a movimentação ortodôntica, a influência destes hormônios na movimentação dentária após remoção do aparelho ortodôntico e na estrutura óssea alveolar durante esta fase ainda não foi escl...

Wind turbine improvements by wind-lidar-based preview and control

DEFF Research Database (Denmark)

Mikkelsen, Torben

2014-01-01

Wind turbines equipped with laser prevision hold potential for up to 6+ years lifetime extension. Forward looking wind lidars integrated within operational wind turbines providing feed-forward control can reduce the daily operation loads. The turbine lifetime may in this way be extended by up to 30...

Capturing the journey of wind from the wind turbines (poster)

NARCIS (Netherlands)

Giyanani, A.H.; Bierbooms, W.A.A.M.; Van Bussel, G.J.W.

2015-01-01

Wind turbine design, control strategies often assume Taylor’s frozen turbulence where the fluctuating part of the wind is assumed to be constant. In practise, the wind turbine faces higher turbulence in case of gusts and lower turbulence in some cases. With Lidar technology, the frozen turbulence

A multiple-fan active control wind tunnel for outdoor wind speed and direction simulation

Science.gov (United States)

Wang, Jia-Ying; Meng, Qing-Hao; Luo, Bing; Zeng, Ming

2018-03-01

This article presents a new type of active controlled multiple-fan wind tunnel. The wind tunnel consists of swivel plates and arrays of direct current fans, and the rotation speed of each fan and the shaft angle of each swivel plate can be controlled independently for simulating different kinds of outdoor wind fields. To measure the similarity between the simulated wind field and the outdoor wind field, wind speed and direction time series of two kinds of wind fields are recorded by nine two-dimensional ultrasonic anemometers, and then statistical properties of the wind signals in different time scales are analyzed based on the empirical mode decomposition. In addition, the complexity of wind speed and direction time series is also investigated using multiscale entropy and multivariate multiscale entropy. Results suggest that the simulated wind field in the multiple-fan wind tunnel has a high degree of similarity with the outdoor wind field.

Wind/Hybrid Electricity Applications

Energy Technology Data Exchange (ETDEWEB)

McDaniel, Lori [Iowa Department of Natural Resources, Des Moines, IA (United States)

2001-03-01

Wind energy is widely recognized as the most efficient and cost effective form of new renewable energy available in the Midwest. New utility-scale wind farms (arrays of large turbines in high wind areas producing sufficient energy to serve thousands of homes) rival the cost of building new conventional forms of combustion energy plants, gas, diesel and coal power plants. Wind energy is not subject to the inflationary cost of fossil fuels. Wind energy can also be very attractive to residential and commercial electric customers in high wind areas who would like to be more self-sufficient for their energy needs. And wind energy is friendly to the environment at a time when there is increasing concern about pollution and climate change. However, wind energy is an intermittent source of power. Most wind turbines start producing small amounts of electricity at about 8-10 mph (4 meters per second) of wind speed. The turbine does not reach its rated output until the wind reaches about 26-28 mph (12 m/s). So what do you do for power when the output of the wind turbine is not sufficient to meet the demand for energy? This paper will discuss wind hybrid technology options that mix wind with other power sources and storage devices to help solve this problem. This will be done on a variety of scales on the impact of wind energy on the utility system as a whole, and on the commercial and small-scale residential applications. The average cost and cost-benefit of each application along with references to manufacturers will be given. Emerging technologies that promise to shape the future of renewable energy will be explored as well.

Careers in Wind Energy

Science.gov (United States)

Liming, Drew; Hamilton, James

2011-01-01

As a common form of renewable energy, wind power is generating more than just electricity. It is increasingly generating jobs for workers in many different occupations. Many workers are employed on wind farms: areas where groups of wind turbines produce electricity from wind power. Wind farms are frequently located in the midwestern, western, and…

Using Satellite SAR to Characterize the Wind Flow around Offshore Wind Farms

DEFF Research Database (Denmark)

Hasager, Charlotte Bay; Vincent, Pauline; Badger, Jake

2015-01-01

Offshore wind farm cluster effects between neighboring wind farms increase rapidly with the large-scale deployment of offshore wind turbines. The wind farm wakes observed from Synthetic Aperture Radar (SAR) are sometimes visible and atmospheric and wake models are here shown to convincingly repro...

Forest trees filter chronic wind-signals to acclimate to high winds.

Science.gov (United States)

Bonnesoeur, Vivien; Constant, Thiéry; Moulia, Bruno; Fournier, Meriem

2016-05-01

Controlled experiments have shown that trees acclimate thigmomorphogenetically to wind-loads by sensing their deformation (strain). However, the strain regime in nature is exposed to a full spectrum of winds. We hypothesized that trees avoid overreacting by responding only to winds which bring information on local climate and/or wind exposure. Additionally, competition for light dependent on tree social status also likely affects thigmomorphogenesis. We monitored and manipulated quantitatively the strain regimes of 15 pairs of beech (Fagus sylvatica) trees of contrasting social status in an acclimated stand, and quantified the effects of these regimes on the radial growth over a vegetative season. Trees exposed to artificial bending, the intensity of which corresponds to the strongest wind-induced strains, enhanced their secondary growth by at least 80%. Surprisingly, this reaction was even greater - relatively - for suppressed trees than for dominant ones. Acclimated trees did not sense the different types of wind events in the same way. Daily wind speed peaks due to thermal winds were filtered out. Thigmomorphogenesis was therefore driven by intense storms. Thigmomorphogenesis is also likely to be involved in determining social status. © 2016 The Authors. New Phytologist © 2016 New Phytologist Trust.

Minimisation of Generation Variability of a Group of Wind Plants

Directory of Open Access Journals (Sweden)

Dubravko Sabolić

2017-09-01

Full Text Available Minimisation of variability of energy delivered from a group of wind plants into the power system using portfolio theory approach was studied. One of the assumptions of that theory is Gaussian distribution of the sample, which is not satisfied in case of wind generation. Therefore, optimisation of a “portfolio” of plants with different goal functions was studied. It was supposed that a decision on distribution of a fixed amount of generation capacity to be installed among a set of geographical locations with known wind statistics is to be made with minimised variability of generation as a goal. In that way the statistical cancellation of variability would be used in the best possible manner. This article is a brief report on results of such an investigation. An example of nine locations in Croatia was used. These locations’ wind statistics are known from historic generation data.

Wind farm power production in the changing wind: Robustness quantification and layout optimization

DEFF Research Database (Denmark)

Feng, Ju; Shen, Wen Zhong

2017-01-01

Wind farms operate often in the changing wind. The wind condition variations in a wide range of time scales lead to the variability of wind farms’ power production. This imposes a major challenge to the power system operators who are facing a higher and higher penetration level of wind power. Thu...

Operation and Equivalent Loads of Wind Turbines in Large Wind Farms

Science.gov (United States)

Andersen, Soren Juhl; Sorensen, Jens Norkaer; Mikkelsen, Robert Flemming

2017-11-01

Wind farms continue to grow in size and as the technology matures, the design of wind farms move towards including dynamic effects besides merely annual power production estimates. The unsteady operation of wind turbines in large wind farms has been modelled with EllipSys3D(Michelsen, 1992, and Sørensen, 1995) for a number of different scenarios using a fully coupled large eddy simulations(LES) and aero-elastic framework. The turbines are represented in the flow fields using the actuator line method(Sørensen and Shen, 2002), where the aerodynamic forces and deflections are derived from an aero-elastic code, Flex5(Øye, 1996). The simulations constitute a database of full turbine operation in terms of both production and loads for various wind speeds, turbulence intensities, and turbine spacings. The operating conditions are examined in terms of averaged power production and thrust force, as well as 10min equivalent flapwise bending, yaw, and tilt moment loads. The analyses focus on how the performance and loads change throughout a given farm as well as comparing how various input parameters affect the operation and loads of the wind turbines during different scenarios. COMWIND(Grant 2104-09- 067216/DSF), Nordic Consortium on Optimization and Control of Wind Farms, Eurotech Greentech Wind project, Winds2Loads, and CCA LES. Ressources Granted on SNIC and JESS. The Vestas NM80 turbine has been used.

Canadian small wind market

International Nuclear Information System (INIS)

Moorhouse, E.

2010-01-01

This PowerPoint presentation discussed initiatives and strategies adopted by the Canadian Wind Energy Association (CanWEA) to support the development of Canada's small wind market. The general public has shown a significant interest in small wind projects of 300 kW. Studies have demonstrated that familiarity and comfort with small wind projects can help to ensure the successful implementation of larger wind projects. Small wind markets include residential, farming and commercial, and remote community applications. The results of CanWEA market survey show that the small wind market grew by 78 percent in 2008 over 2007, and again in 2009 by 32 percent over 2008. The average turbine size is 1 kW. A total of 11,000 turbines were purchased in 2007 and 2008. Global small wind market growth increased by 110 percent in 2008, and the average turbine size was 2.4 kW. Eighty-seven percent of the turbines made by Canadian mid-size wind turbine manufacturers are exported, and there is now a significant risk that Canada will lose its competitive advantage in small wind manufacturing as financial incentives have not been implemented. American and Canadian-based small wind manufacturers were listed, and small wind policies were reviewed. The presentation concluded with a set of recommendations for future incentives, educational programs and legislation. tabs., figs.

Wind Turbine Generator Modeling and Simulation Where Rotational Speed is the Controlled Variable

DEFF Research Database (Denmark)

Mihet-Popa, Lucian; Blaabjerg, Frede; Boldea, Ion

2004-01-01

the interaction between a wind turbine and the power system. The model is intended to simulate the behaviour of the wind turbine using induction generators both during normal operation. Sample simulation results for two induction generators (2/0.5 MW) validate the fundamental issues.......To optimise the power produced in a wind turbine, the speed of the turbine should vary with the wind speed. A simple control method is proposed that will allow an induction machine to run a turbine at its maximum power coefficient. Various types of power control strategies have been suggested...... for application in variable speed wind turbines. The usual strategy is to control the power or the torque acting on the wind turbine shafts. This paper presents an alternative control strategy, where the rotational speed is the controlled variable. The paper describes a model, which is being developed to simulate...

Husum wind `97. Amiable and powerful. Proceedings; Husum Wind `97. Liebenswert und leistungsstark. Kongressband

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

The Husum Fair and Congress on Wind Energy 97 wants to inform on and demonstrate the state of the art of wind energy and its potentials of development. This conference volume contains 21 papers in seven sections: Wind energy - society and environment; forum of the wind power plant manufacturers represented at the Husum Wind 97; foreign markets for wind power plants; development prospects for wind power; wind power in retrospective and relevant operating experience; panel discussion ``The amendment to the act on remuneration for power fed into the mains - wind power in the lull``; excursion to the test field WINDTEST, Kaiser-Wilhelm-Koog. (AKF)