A Preliminary Version of Heavy Ion Treatment Planning System at IMP

International Nuclear Information System (INIS)

Liu Xinguo; Dai Zhongying; Ye Fei; Wu Qingfeng; Li Ping; Li Qiang; Jin Xiaodong; Du Xiaogang; WangYangping; Dang Jianwu

2010-01-01

Based on the Heavy Ion Research Facility in Lanzhou (HIRFL/HIRFL-CSR), clinical trials of heavy ion radiotherapy are being conducted at the Institute of Modern Physics (IMP), Chinese Academy of Sciences, where two-dimensional(2D) layer-stacking conformal irradiation method in a passive beam delivery system was applied. To make better use of the biophysical advantages of heavy ion beams and ensure success of the clinical trials, a preliminary version of heavy ion treatment planning system (TPS) has been developed at IMP. The TPS was designed in a manner to adapt to the 2D layer-stacking conformal irradiation method. The architecture and function of the TPS software and the implementation of dose calculation algorithm in the TPS were introduced in this paper.The deviation between the doses planned by the TPS and measured through an anthropomorphous phantom was verified to be less than 5%. Finally,the pending issues for developing a sophisticated treatment planning system at IMP were discussed. (authors)

Radioactive materials and waste. Planning Act of 28 June 2006. Consolidated version established by Andra

International Nuclear Information System (INIS)

2013-07-01

This document is the English translation of the Articles of the Planning Act No. 2006-739 of 28 June 2006 and of the articles L. 542-1 and following of the Environmental Code (as modified) concerning the Sustainable Management of Radioactive Materials and Waste. This translation is provided for convenience purposes only, the French version remaining the only valid and legally-binding version. In order to enhance readability, all articles relating to Andra's activities are consolidated in this self-supporting document

Long-Term Ecological Monitoring Field Sampling Plan for 2007

International Nuclear Information System (INIS)

T. Haney R. VanHorn

2007-01-01

This field sampling plan describes the field investigations planned for the Long-Term Ecological Monitoring Project at the Idaho National Laboratory Site in 2007. This plan and the Quality Assurance Project Plan for Waste Area Groups 1, 2, 3, 4, 5, 6, 7, 10, and Removal Actions constitute the sampling and analysis plan supporting long-term ecological monitoring sampling in 2007. The data collected under this plan will become part of the long-term ecological monitoring data set that is being collected annually. The data will be used to determine the requirements for the subsequent long-term ecological monitoring. This plan guides the 2007 investigations, including sampling, quality assurance, quality control, analytical procedures, and data management. As such, this plan will help to ensure that the resulting monitoring data will be scientifically valid, defensible, and of known and acceptable quality

Long-Term Ecological Monitoring Field Sampling Plan for 2007

Energy Technology Data Exchange (ETDEWEB)

T. Haney

2007-07-31

This field sampling plan describes the field investigations planned for the Long-Term Ecological Monitoring Project at the Idaho National Laboratory Site in 2007. This plan and the Quality Assurance Project Plan for Waste Area Groups 1, 2, 3, 4, 5, 6, 7, 10, and Removal Actions constitute the sampling and analysis plan supporting long-term ecological monitoring sampling in 2007. The data collected under this plan will become part of the long-term ecological monitoring data set that is being collected annually. The data will be used t determine the requirements for the subsequent long-term ecological monitoring. This plan guides the 2007 investigations, including sampling, quality assurance, quality control, analytical procedures, and data management. As such, this plan will help to ensure that the resulting monitoring data will be scientifically valid, defensible, and of known and acceptable quality.

NCTPlan. The new PC version of MacNCTPlan improvements and validation of the treatment planning system

International Nuclear Information System (INIS)

Gonzalez, S.J.; Santa Cruz, Gustavo A.; Yam, C.S.

2003-01-01

Full text: The treatment planning system that has been used routinely in phase-I clinical trials of BNCT at Harvard/MIT consists of the MacNCTPlan interactive planning software coupled to the MCNP 4B Monte Carlo radiation transport code. The physical and mathematical principles of MacNCTPlan as well as its architecture, operation and application have been previously described elsewhere. The use of this software in clinical trials together with a detailed analysis of the code led to the identification of some limitations and deficiencies. The motivation for this PC version, Neutron Capture Therapy Planning, relies basically in two major reasons: the need to integrate the different steps for making a plan and the need to improve some features of the Macintosh version. NCTPlan aims to reproduce all the features and capabilities present in the Macintosh version. Working on this, some deficiencies were corrected and several changes in the interface were performed in order to provide a more friendly and reliable program. Among the changes intended to facilitate the treatment planning process, the most important are the integration of the auxiliary program MPREP to NCTPlan and a great improvement in the visualization of isodose contours. NCTPlan has the ability to show the isodose distributions superimposed on two orthogonal planes of the CT volume, these planes being updated in real time as the orientation of the planes is changed. The major modifications to the mathematical algorithms concerned the material assignment in the geometric model, dose distribution calculations and three-dimensional dose-volume histogram (DVH) derivation. Therefore, NCTPlan provides a user-friendly interface thanks to the integration of the different steps involved in treatment planning. Complete control of the MCNP radiation transport code is under study. Cross-validation of NCTPlan against reference calculations made apparent the improvements performed on the mathematical algorithms

Nevada National Security Site Integrated Groundwater Sampling Plan, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Marutzky, Sam; Farnham, Irene

2014-10-01

The purpose of the Nevada National Security Site (NNSS) Integrated Sampling Plan (referred to herein as the Plan) is to provide a comprehensive, integrated approach for collecting and analyzing groundwater samples to meet the needs and objectives of the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO) Underground Test Area (UGTA) Activity. Implementation of this Plan will provide high-quality data required by the UGTA Activity for ensuring public protection in an efficient and cost-effective manner. The Plan is designed to ensure compliance with the UGTA Quality Assurance Plan (QAP). The Plan’s scope comprises sample collection and analysis requirements relevant to assessing the extent of groundwater contamination from underground nuclear testing. This Plan identifies locations to be sampled by corrective action unit (CAU) and location type, sampling frequencies, sample collection methodologies, and the constituents to be analyzed. In addition, the Plan defines data collection criteria such as well-purging requirements, detection levels, and accuracy requirements; identifies reporting and data management requirements; and provides a process to ensure coordination between NNSS groundwater sampling programs for sampling of interest to UGTA. This Plan does not address compliance with requirements for wells that supply the NNSS public water system or wells involved in a permitted activity.

Final Sampling and Analysis Plan for Background Sampling, Fort Sheridan, Illinois

National Research Council Canada - National Science Library

1995-01-01

.... This Background Sampling and Analysis Plan (BSAP) is designed to address this issue through the collection of additional background samples at Fort Sheridan to support the statistical analysis and the Baseline Risk Assessment (BRA...

Integrated sampling and analysis plan for samples measuring >10 mrem/hour

International Nuclear Information System (INIS)

Haller, C.S.

1992-03-01

This integrated sampling and analysis plan was prepared to assist in planning and scheduling of Hanford Site sampling and analytical activities for all waste characterization samples that measure greater than 10 mrem/hour. This report also satisfies the requirements of the renegotiated Interim Milestone M-10-05 of the Hanford Federal Facility Agreement and Consent Order (the Tri-Party Agreement). For purposes of comparing the various analytical needs with the Hanford Site laboratory capabilities, the analytical requirements of the various programs were normalized by converting required laboratory effort for each type of sample to a common unit of work, the standard analytical equivalency unit (AEU). The AEU approximates the amount of laboratory resources required to perform an extensive suite of analyses on five core segments individually plus one additional suite of analyses on a composite sample derived from a mixture of the five core segments and prepare a validated RCRA-type data package

Group Acceptance Sampling Plan for Lifetime Data Using Generalized Pareto Distribution

Directory of Open Access Journals (Sweden)

Muhammad Aslam

2010-02-01

Full Text Available In this paper, a group acceptance sampling plan (GASP is introduced for the situations when lifetime of the items follows the generalized Pareto distribution. The design parameters such as minimum group size and acceptance number are determined when the consumer’s risk and the test termination time are specified. The proposed sampling plan is compared with the existing sampling plan. It is concluded that the proposed sampling plan performs better than the existing plan in terms of minimum sample size required to reach the same decision.

Nevada National Security Site Integrated Groundwater Sampling Plan, Revision 1

Energy Technology Data Exchange (ETDEWEB)

Farnham, Irene

2018-03-01

The purpose is to provide a comprehensive, integrated approach for collecting and analyzing groundwater samples to meet the needs and objectives of the DOE/EM Nevada Program’s UGTA Activity. Implementation of this Plan will provide high-quality data required by the UGTA Activity for ensuring public protection in an efficient and cost-effective manner. The Plan is designed to ensure compliance with the UGTA Quality Assurance Plan (QAP) (NNSA/NFO, 2015); Federal Facility Agreement and Consent Order (FFACO) (1996, as amended); and DOE Order 458.1, Radiation Protection of the Public and the Environment (DOE, 2013). The Plan’s scope comprises sample collection and analysis requirements relevant to assessing both the extent of groundwater contamination from underground nuclear testing and impact of testing on water quality in downgradient communities. This Plan identifies locations to be sampled by CAU and location type, sampling frequencies, sample collection methodologies, and the constituents to be analyzed. In addition, the Plan defines data collection criteria such as well purging, detection levels, and accuracy requirements/recommendations; identifies reporting and data management requirements; and provides a process to ensure coordination between NNSS groundwater sampling programs for sampling analytes of interest to UGTA. Information used in the Plan development—including the rationale for selection of wells, sampling frequency, and the analytical suite—is discussed under separate cover (N-I, 2014) and is not reproduced herein. This Plan does not address compliance for those wells involved in a permitted activity. Sampling and analysis requirements associated with these wells are described in their respective permits and are discussed in NNSS environmental reports (see Section 5.2). In addition, sampling for UGTA CAUs that are in the Closure Report (CR) stage are not included in this Plan. Sampling requirements for these CAUs are described in the CR

Particular intervention plan of the Civaux Nuclear Power Plant. Public version. Special provision of the organisation plan for civil protection response

International Nuclear Information System (INIS)

2016-04-01

The Particular intervention plan (PPI in French) is an emergency plan which foresees the measures and means to be implemented to address the potential risks of the presence and operation of a nuclear facility. This plan is implemented and developed by the Prefect in case of nuclear accident (or incident leading to a potential accident), the impact of which extending beyond the facility perimeter. It represents a special section of the organisation plan for civil protection response (ORSEC plan). The PPI foresees the necessary measures and means for crisis management during the first hours following the accident and is triggered by the Department Prefect according to the information provided by the facility operator. Its aim is to protect the populations leaving within 10 km of the facility against a potential radiological hazard. The PPI describes: the facility, the intervention area, the protection measures for the population, the conditions of emergency plan triggering, the crisis organisation, the action forms of the different services, and the post-accident stage. This document is the public version of the Particular intervention plan of the Civaux nuclear power plant (Vienne, France)

42 CFR 431.814 - Sampling plan and procedures.

Science.gov (United States)

2010-10-01

... reliability of the reduced sample. (4) The sample selection procedure. Systematic random sampling is... sampling, and yield estimates with the same or better precision than achieved in systematic random sampling... 42 Public Health 4 2010-10-01 2010-10-01 false Sampling plan and procedures. 431.814 Section 431...

UMTRA project water sampling and analysis plan, Gunnison, Colorado

International Nuclear Information System (INIS)

1994-06-01

This water sampling and analysis plan summarizes the results of previous water sampling activities and the plan for water sampling activities for calendar year 1994. A buffer zone monitoring plan is included as an appendix. The buffer zone monitoring plan is designed to protect the public from residual contamination that entered the ground water as a result of former milling operations. Surface remedial action at the Gunnison Uranium Mill Tailings Remedial Action Project site began in 1992; completion is expected in 1995. Ground water and surface water will be sampled semiannually in 1994 at the Gunnison processing site (GUN-01) and disposal site (GUN-08). Results of previous water sampling at the Gunnison processing site indicate that ground water in the alluvium is contaminated by the former uranium processing activities. Background ground water conditions have been established in the uppermost aquifer (Tertiary gravels) at the Gunnison disposal site. The monitor well locations provide a representative distribution of sampling points to characterize ground water quality and ground water flow conditions in the vicinity of the sites. The list of analytes has been modified with time to reflect constituents that are related to uranium processing activities and the parameters needed for geochemical evaluation. Water sampling will be conducted at least semiannually during and one year following the period of construction activities, to comply with the ground water protection strategy discussed in the remedial action plan (DOE, 1992a)

Wien Automatic System Planning (WASP) Package. A computer code for power generating system expansion planning. Version WASP-III Plus. User's manual. Volume 1: Chapters 1-11

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

As a continuation of its effort to provide comprehensive and impartial guidance to Member States facing the need for introducing nuclear power, the IAEA has completed a new version of the Wien Automatic System Planning (WASP) Package for carrying out power generation expansion planning studies. WASP was originally developed in 1972 in the USA to meet the IAEA's needs to analyze the economic competitiveness of nuclear power in comparison to other generation expansion alternatives for supplying the future electricity requirements of a country or region. The model was first used by the IAEA to conduct global studies (Market Survey for Nuclear Power Plants in Developing Countries, 1972-1973) and to carry out Nuclear Power Planning Studies for several Member States. The WASP system developed into a very comprehensive planning tool for electric power system expansion analysis. Following these developments, the so-called WASP-Ill version was produced in 1979. This version introduced important improvements to the system, namely in the treatment of hydroelectric power plants. The WASP-III version has been continually updated and maintained in order to incorporate needed enhancements. In 1981, the Model for Analysis of Energy Demand (MAED) was developed in order to allow the determination of electricity demand, consistent with the overall requirements for final energy, and thus, to provide a more adequate forecast of electricity needs to be considered in the WASP study. MAED and WASP have been used by the Agency for the conduct of Energy and Nuclear Power Planning Studies for interested Member States. More recently, the VALORAGUA model was completed in 1992 as a means for helping in the preparation of the hydro plant characteristics to be input in the WASP study and to verify that the WASP overall optimized expansion plan takes also into account an optimization of the use of water for electricity generation. The combined application of VALORAGUA and WASP permits the

Sample Lesson Plans. Management for Effective Teaching.

Science.gov (United States)

Fairfax County Public Schools, VA. Dept. of Instructional Services.

This guide is part of the Management for Effective Teaching (MET) support kit, a pilot project developed by the Fairfax County (Virginia) Public Schools to assist elementary school teachers in planning, managaing, and implementing the county's curriculum, Program of Studies (POS). In this guide, a sample lesson plan of a teaching-learning activity…

Sample management implementation plan: Salt Repository Project

International Nuclear Information System (INIS)

1987-01-01

The purpose of the Sample Management Implementation Plan is to define management controls and building requirements for handling materials collected during the site characterization of the Deaf Smith County, Texas, site. This work will be conducted for the US Department of Energy Salt Repository Project Office (SRPO). The plan provides for controls mandated by the US Nuclear Regulatory Commission and the US Environmental Protection Agency. Salt Repository Project (SRP) Sample Management will interface with program participants who request, collect, and test samples. SRP Sample Management will be responsible for the following: (1) preparing samples; (2) ensuring documentation control; (3) providing for uniform forms, labels, data formats, and transportation and storage requirements; and (4) identifying sample specifications to ensure sample quality. The SRP Sample Management Facility will be operated under a set of procedures that will impact numerous program participants. Requesters of samples will be responsible for definition of requirements in advance of collection. Sample requests for field activities will be approved by the SRPO, aided by an advisory group, the SRP Sample Allocation Committee. This document details the staffing, building, storage, and transportation requirements for establishing an SRP Sample Management Facility. Materials to be managed in the facility include rock core and rock discontinuities, soils, fluids, biota, air particulates, cultural artifacts, and crop and food stuffs. 39 refs., 3 figs., 11 tabs

Public information plan. Version 2

International Nuclear Information System (INIS)

1993-01-01

The Public Information Plan is intended to be used in conjunction with the U.S. Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project Public Participation Plan. The Public Participation Pion describes the DOE procedure for involving the public in the decision-making process related to the UMTRA Project during the stages at which public participation is required and solicited. This Public Information Plan describes the department's procedure for communicating with the public about project policies, plans, and activities. Together, these complementary plans describe the DOE public affairs program for the UMTRA Project. This project was authorized by Congress in the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, (Public Law (PL) 95-6041), as amended. The Act provides for a cooperative effort with affected states and Indian tribes for the cleanup of designated abandoned or inactive uranium mill tailings sites, which are located in 10 states, 9 of them west of the Mississippi River. The public has a right to know about proposed government actions and to be heard in the planning of activities that influence their lives. The UMTRA Project is unclassified and the DOE provides accurate information about policy and project activities to interested stakeholders, including the news media, in a timely way. The DOE encourages states and local governments, as well as individuals, to join actively in the decision-making process. This is intended to ensure that the resulting decisions are made with full knowledge of the public's views and that these decisions address the public's concerns to the extent possible within the law. The DOE, through the implementation of the Public Information Plan, keeps the public informed on matters such as health concerns, environmental issues, remedial action construction plans, project costs, and specific site activities

DOE-2 sample run book: Version 2.1E

Energy Technology Data Exchange (ETDEWEB)

Winkelmann, F.C.; Birdsall, B.E.; Buhl, W.F.; Ellington, K.L.; Erdem, A.E. [Lawrence Berkeley Lab., CA (United States); Hirsch, J.J.; Gates, S. [Hirsch (James J.) and Associates, Camarillo, CA (United States)

1993-11-01

The DOE-2 Sample Run Book shows inputs and outputs for a variety of building and system types. The samples start with a simple structure and continue to a high-rise office building, a medical building, three small office buildings, a bar/lounge, a single-family residence, a small office building with daylighting, a single family residence with an attached sunspace, a ``parameterized`` building using input macros, and a metric input/output example. All of the samples use Chicago TRY weather. The main purpose of the Sample Run Book is instructional. It shows the relationship of LOADS-SYSTEMS-PLANT-ECONOMICS inputs, displays various input styles, and illustrates many of the basic and advanced features of the program. Many of the sample runs are preceded by a sketch of the building showing its general appearance and the zoning used in the input. In some cases we also show a 3-D rendering of the building as produced by the program DrawBDL. Descriptive material has been added as comments in the input itself. We find that a number of users have loaded these samples onto their editing systems and use them as ``templates`` for creating new inputs. Another way of using them would be to store various portions as files that can be read into the input using the {number_sign}{number_sign} include command, which is part of the Input Macro feature introduced in version DOE-2.lD. Note that the energy rate structures here are the same as in the DOE-2.lD samples, but have been rewritten using the new DOE-2.lE commands and keywords for ECONOMICS. The samples contained in this report are the same as those found on the DOE-2 release files. However, the output numbers that appear here may differ slightly from those obtained from the release files. The output on the release files can be used as a check set to compare results on your computer.

Wien Automatic System Planning (WASP) Package. A computer code for power generating system expansion planning. Version WASP-III Plus. User's manual. Volume 1: Chapters 1-11

International Nuclear Information System (INIS)

1995-01-01

As a continuation of its effort to provide comprehensive and impartial guidance to Member States facing the need for introducing nuclear power, the IAEA has completed a new version of the Wien Automatic System Planning (WASP) Package for carrying out power generation expansion planning studies. WASP was originally developed in 1972 in the USA to meet the IAEA's needs to analyze the economic competitiveness of nuclear power in comparison to other generation expansion alternatives for supplying the future electricity requirements of a country or region. The model was first used by the IAEA to conduct global studies (Market Survey for Nuclear Power Plants in Developing Countries, 1972-1973) and to carry out Nuclear Power Planning Studies for several Member States. The WASP system developed into a very comprehensive planning tool for electric power system expansion analysis. Following these developments, the so-called WASP-Ill version was produced in 1979. This version introduced important improvements to the system, namely in the treatment of hydroelectric power plants. The WASP-III version has been continually updated and maintained in order to incorporate needed enhancements. In 1981, the Model for Analysis of Energy Demand (MAED) was developed in order to allow the determination of electricity demand, consistent with the overall requirements for final energy, and thus, to provide a more adequate forecast of electricity needs to be considered in the WASP study. MAED and WASP have been used by the Agency for the conduct of Energy and Nuclear Power Planning Studies for interested Member States. More recently, the VALORAGUA model was completed in 1992 as a means for helping in the preparation of the hydro plant characteristics to be input in the WASP study and to verify that the WASP overall optimized expansion plan takes also into account an optimization of the use of water for electricity generation. The combined application of VALORAGUA and WASP permits the

Feasible sampling plan for Bemisia tabaci control decision-making in watermelon fields.

Science.gov (United States)

Lima, Carlos Ho; Sarmento, Renato A; Pereira, Poliana S; Galdino, Tarcísio Vs; Santos, Fábio A; Silva, Joedna; Picanço, Marcelo C

2017-11-01

The silverleaf whitefly Bemisia tabaci is one of the most important pests of watermelon fields worldwide. Conventional sampling plans are the starting point for the generation of decision-making systems of integrated pest management programs. The aim of this study was to determine a conventional sampling plan for B. tabaci in watermelon fields. The optimal leaf for B. tabaci adult sampling was the 6 th most apical leaf. Direct counting was the best pest sampling technique. Crop pest densities fitted the negative binomial distribution and had a common aggregation parameter (K common ). The sampling plan consisted of evaluating 103 samples per plot. This sampling plan was conducted for 56 min, costing US$ 2.22 per sampling and with a 10% maximum evaluation error. The sampling plan determined in this study can be adopted by farmers because it enables the adequate evaluation of B. tabaci populations in watermelon fields (10% maximum evaluation error) and is a low-cost (US$ 2.22 per sampling), fast (56 min per sampling) and feasible (because it may be used in a standardized way throughout the crop cycle) technique. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

UMTRA project water sampling and analysis plan, Tuba City, Arizona

International Nuclear Information System (INIS)

1996-02-01

Planned, routine ground water sampling activities at the U.S. Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site in Tuba City, Arizona, are described in the following sections of this water sampling and analysis plan (WSAP). This plan identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the stations routinely monitored at the site. The ground water data are used for site characterization and risk assessment. The regulatory basis for routine ground water monitoring at UMTRA Project sites is derived from the U.S. Environmental Protection Agency (EPA) regulations in 40 CFR Part 192 (1994) and the final EPA standards of 1995 (60 FR 2854). Sampling procedures are guided by the UMTRA Project standard operating procedures (SOP) (JEG, n.d.), and the most effective technical approach for the site

Hydrogeologic investigations sampling plan: Revision 0

International Nuclear Information System (INIS)

1988-11-01

The goal of this sampling plan is to identify and develop specific plans for those investigative actions necessary to: (1) characterize the hydrologic regime; (2) define the extent and impact of contamination; and (3) predict future contaminant migration for the Weldon Spring Site (WSS) and vicinity. The plan is part of the Weldon Spring Site Remedial Action Project (WSSRAP) sponsored by the US Department of Energy (DOE) and has been developed in accordance with US EPA Remedial Investigation (RI) and Data Quality Objective (DQO) guidelines. The plan consists of a sequence of activities including the evaluation of data, development of a conceptual model, identification of data uses and needs, and the design and implementation of a data collection program. Data will be obtained to: (1) confirm the presence or absence of contaminants; (2) define contaminant sources and modes of transport; (3) delineate extent of contaminant migration and predict future migration; and (4) provide information to support the evaluation and selection of remedial actions. 81 refs., 62 figs., 26 tabs

UMTRA project water sampling and analysis plan, Maybell, Colorado

International Nuclear Information System (INIS)

1994-06-01

This water sampling and analysis plan (WSAP) describes planned water sampling activities and provides the regulatory and technical basis for ground water sampling in 1994 at the US Department of Energy's (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site in Maybell, Colorado. The WSAP identifies and justifies sampling locations, analytical parameters, and sampling frequencies at the site. The ground water data will be used for site characterization and risk assessment. The regulatory basis for the ground water and surface water monitoring activities is derived from the EPA regulations in 40 CFR Part 192 (1993) and the proposed EPA standards of 1987 (52 FR 36000). Sampling procedures are guided by the UMTRA Project standard operating procedures (SOP) (JEG, n.d.), the Technical Approach Document (TAD) (DOE, 1989), and the most effective technical approach for the site. This WSAP also includes a summary and the results of water sampling activities from 1989 through 1992 (no sampling was performed in 1993)

Status of the NASA Micro Pulse Lidar Network (MPLNET): overview of the network and future plans, new version 3 data products, and the polarized MPL

Science.gov (United States)

Welton, Ellsworth J.; Stewart, Sebastian A.; Lewis, Jasper R.; Belcher, Larry R.; Campbell, James R.; Lolli, Simone

2018-04-01

The NASA Micro Pulse Lidar Network (MPLNET) is a global federated network of Micro-Pulse Lidars (MPL) co-located with the NASA Aerosol Robotic Network (AERONET). MPLNET began in 2000, and there are currently 17 long-term sites, numerous field campaigns, and more planned sites on the way. We have developed a new Version 3 processing system including the deployment of polarized MPLs across the network. Here we provide an overview of Version 3, the polarized MPL, and current and future plans.

The Toggle Local Planner for sampling-based motion planning

KAUST Repository

Denny, Jory; Amato, Nancy M.

2012-01-01

Sampling-based solutions to the motion planning problem, such as the probabilistic roadmap method (PRM), have become commonplace in robotics applications. These solutions are the norm as the dimensionality of the planning space grows, i.e., d > 5

UMTRA Project water sampling and analysis plan, Gunnison, Colorado: Revision 1

International Nuclear Information System (INIS)

1994-11-01

This water sampling and analysis plan summarizes the results of previous water sampling activities and the plan for future water sampling activities, in accordance with the Guidance Document for Preparing Sampling and Analysis Plans for UMTRA Sites. A buffer zone monitoring plan for the Dos Rios Subdivision is included as an appendix. The buffer zone monitoring plan was developed to ensure continued protection to the public from residual contamination. The buffer zone is beyond the area depicted as contaminated ground water due to former milling operations. Surface remedial action at the Gunnison Uranium Mill Tailings Remedial Action Project site began in 1992; completion is expected in 1995. Ground water and surface water will be sampled semiannually at the Gunnison processing site and disposal site. Results of previous water sampling at the Gunnison processing site indicate that ground water in the alluvium is contaminated by the former uranium processing activities. Background ground water conditions have been established in the uppermost aquifer at the Gunnison disposal site. The monitor well locations provide a representative distribution of sampling points to characterize ground water quality and ground water flow conditions in the vicinity of the sites. The list of analytes has been modified with time to reflect constituents that are related to uranium processing activities and the parameters needed for geochemical evaluation

Psychometric Properties of the Slovak Version of sEMBU on General Adult Sample

Directory of Open Access Journals (Sweden)

Gugová Gabriela Rozvadský

2016-12-01

Full Text Available The factorial stability and reliability of the 23-item s(short- EMBU previously demonstrated to be satisfactory in the samples of students from Greece, Guatemala, Hungary, Italy (1999, East-Germany and Sweden (Arrindell et al., 2001. The Slovak translation of the original sEMBU was published in 2007 (Poliaková, Mojžišová, & Hašto, 2007. We decided to explore the psychometric properties of the translation of sEMBU on a general adult sample (N=970 in Slovakia, because the translated version of sEMBU is already utilized in research projects in Slovakia. The results show a very good alpha reliability of sEMBU. In the Slovak translation, we found similar scores of Rejection and Emotional warmth and Overprotection. A factor analysis with forced 3-factor solution sorted items to scales exactly as authors of sEMBU presupposed. Overprotection (father has the highest share for classification and differentiation in the cluster. Emotional warmth (mother has the highest share for classification and differentiation in the cluster. We discussed our results with the results from other studies and we suggest to continue in the research of the Slovak version of sEMBU focused on types of attachment, especially on the secure type of attachment.

Sample collection and sample analysis plan in support of the 105-C/190-C concrete and soil sampling activities

International Nuclear Information System (INIS)

Marske, S.G.

1996-07-01

This sampling and analysis plan describes the sample collection and sample analysis in support of the 105-C water tunnels and 190-C main pumphouse concrete and soil sampling activities. These analytical data will be used to identify the radiological contamination and presence of hazardous materials to support the decontamination and disposal activities

Portuguese version of the PTSD Checklist-Military Version (PCL-M)-I: Confirmatory Factor Analysis and reliability.

Science.gov (United States)

Carvalho, Teresa; Cunha, Marina; Pinto-Gouveia, José; Duarte, Joana

2015-03-30

The PTSD Checklist-Military Version (PCL-M) is a brief self-report instrument widely used to assess Post-traumatic Stress Disorder (PTSD) symptomatology in war Veterans, according to DSM-IV. This study sought out to explore the factor structure and reliability of the Portuguese version of the PCL-M. A sample of 660 Portuguese Colonial War Veterans completed the PCL-M. Several Confirmatory Factor Analyses were conducted to test different structures for PCL-M PTSD symptoms. Although the respecified first-order four-factor model based on King et al.'s model showed the best fit to the data, the respecified first and second-order models based on the DSM-IV symptom clusters also presented an acceptable fit. In addition, the PCL-M showed adequate reliability. The Portuguese version of the PCL-M is thus a valid and reliable measure to assess the severity of PTSD symptoms as described in DSM-IV. Its use with Portuguese Colonial War Veterans may ease screening of possible PTSD cases, promote more suitable treatment planning, and enable monitoring of therapeutic outcomes. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

UMTRA water sampling and analysis plan, Green River, Utah

International Nuclear Information System (INIS)

Papusch, R.

1993-12-01

The purpose of this water sampling and analysis plan (WSAP) is to provide a basis for groundwater and surface water sampling at the Green River Uranium Mill Tailing Remedial Action (UMTRA) Project site. This WSAP identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the monitoring locations

Compatibility Grab Sampling and Analysis Plan for Fiscal Year 2001

International Nuclear Information System (INIS)

LAURICELLA, T.L.

2000-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for grab samples obtained to address waste compatibility

Status of the NASA Micro Pulse Lidar Network (MPLNET: overview of the network and future plans, new version 3 data products, and the polarized MPL

Directory of Open Access Journals (Sweden)

Welton Ellsworth J.

2018-01-01

Full Text Available The NASA Micro Pulse Lidar Network (MPLNET is a global federated network of Micro-Pulse Lidars (MPL co-located with the NASA Aerosol Robotic Network (AERONET. MPLNET began in 2000, and there are currently 17 long-term sites, numerous field campaigns, and more planned sites on the way. We have developed a new Version 3 processing system including the deployment of polarized MPLs across the network. Here we provide an overview of Version 3, the polarized MPL, and current and future plans.

Nitrate Waste Treatment Sampling and Analysis Plan

Energy Technology Data Exchange (ETDEWEB)

Vigil-Holterman, Luciana R. [Los Alamos National Laboratory; Martinez, Patrick Thomas [Los Alamos National Laboratory; Garcia, Terrence Kerwin [Los Alamos National Laboratory

2017-07-05

This plan is designed to outline the collection and analysis of nitrate salt-bearing waste samples required by the New Mexico Environment Department- Hazardous Waste Bureau in the Los Alamos National Laboratory (LANL) Hazardous Waste Facility Permit (Permit).

Sampling plans for pest mites on physic nut.

Science.gov (United States)

Rosado, Jander F; Sarmento, Renato A; Pedro-Neto, Marçal; Galdino, Tarcísio V S; Marques, Renata V; Erasmo, Eduardo A L; Picanço, Marcelo C

2014-08-01

The starting point for generating a pest control decision-making system is a conventional sampling plan. Because the mites Polyphagotarsonemus latus and Tetranychus bastosi are among the most important pests of the physic nut (Jatropha curcas), in the present study, we aimed to establish sampling plans for these mite species on physic nut. Mite densities were monitored in 12 physic nut crops. Based on the obtained results, sampling of P. latus and T. bastosi should be performed by assessing the number of mites per cm(2) in 160 samples using a handheld 20× magnifying glass. The optimal sampling region for T. bastosi is the abaxial surface of the 4th most apical leaf on the branch of the middle third of the canopy. On the abaxial surface, T. bastosi should then be observed on the side parts of the middle portion of the leaf, near its edge. As for P. latus, the optimal sampling region is the abaxial surface of the 4th most apical leaf on the branch of the apical third of the canopy on the abaxial surface. Polyphagotarsonemus latus should then be assessed on the side parts of the leaf's petiole insertion. Each sampling procedure requires 4 h and costs US$ 7.31.

Using Load Balancing to Scalably Parallelize Sampling-Based Motion Planning Algorithms

KAUST Repository

Fidel, Adam; Jacobs, Sam Ade; Sharma, Shishir; Amato, Nancy M.; Rauchwerger, Lawrence

2014-01-01

Motion planning, which is the problem of computing feasible paths in an environment for a movable object, has applications in many domains ranging from robotics, to intelligent CAD, to protein folding. The best methods for solving this PSPACE-hard problem are so-called sampling-based planners. Recent work introduced uniform spatial subdivision techniques for parallelizing sampling-based motion planning algorithms that scaled well. However, such methods are prone to load imbalance, as planning time depends on region characteristics and, for most problems, the heterogeneity of the sub problems increases as the number of processors increases. In this work, we introduce two techniques to address load imbalance in the parallelization of sampling-based motion planning algorithms: an adaptive work stealing approach and bulk-synchronous redistribution. We show that applying these techniques to representatives of the two major classes of parallel sampling-based motion planning algorithms, probabilistic roadmaps and rapidly-exploring random trees, results in a more scalable and load-balanced computation on more than 3,000 cores. © 2014 IEEE.

Using Load Balancing to Scalably Parallelize Sampling-Based Motion Planning Algorithms

KAUST Repository

Fidel, Adam

2014-05-01

Motion planning, which is the problem of computing feasible paths in an environment for a movable object, has applications in many domains ranging from robotics, to intelligent CAD, to protein folding. The best methods for solving this PSPACE-hard problem are so-called sampling-based planners. Recent work introduced uniform spatial subdivision techniques for parallelizing sampling-based motion planning algorithms that scaled well. However, such methods are prone to load imbalance, as planning time depends on region characteristics and, for most problems, the heterogeneity of the sub problems increases as the number of processors increases. In this work, we introduce two techniques to address load imbalance in the parallelization of sampling-based motion planning algorithms: an adaptive work stealing approach and bulk-synchronous redistribution. We show that applying these techniques to representatives of the two major classes of parallel sampling-based motion planning algorithms, probabilistic roadmaps and rapidly-exploring random trees, results in a more scalable and load-balanced computation on more than 3,000 cores. © 2014 IEEE.

Economic Design of Acceptance Sampling Plans in a Two-Stage Supply Chain

Directory of Open Access Journals (Sweden)

Lie-Fern Hsu

2012-01-01

Full Text Available Supply Chain Management, which is concerned with material and information flows between facilities and the final customers, has been considered the most popular operations strategy for improving organizational competitiveness nowadays. With the advanced development of computer technology, it is getting easier to derive an acceptance sampling plan satisfying both the producer's and consumer's quality and risk requirements. However, all the available QC tables and computer software determine the sampling plan on a noneconomic basis. In this paper, we design an economic model to determine the optimal sampling plan in a two-stage supply chain that minimizes the producer's and the consumer's total quality cost while satisfying both the producer's and consumer's quality and risk requirements. Numerical examples show that the optimal sampling plan is quite sensitive to the producer's product quality. The product's inspection, internal failure, and postsale failure costs also have an effect on the optimal sampling plan.

UMTRA Project water sampling and analysis plan, Salt Lake City, Utah. Revision 1

International Nuclear Information System (INIS)

1995-06-01

This water sampling and analysis plan describes planned, routine ground water sampling activities at the US Department of Energy Uranium Mill Tailings Remedial Action Project site in Salt Lake City, Utah. This plan identifies and justifies sampling locations, analytical parameters, detection limits, and sampling frequencies for routine monitoring of ground water, sediments, and surface waters at monitoring stations on the site

SU-E-T-357: Semi-Automated Knowledge-Based Radiation Therapy (KBRT) Planning for Head-And-Neck Cancer (HNC): Can KBRT Plans Achieve Better Results Than Manual Planning?

International Nuclear Information System (INIS)

Lutzky, C; Grzetic, S; Lo, J; Das, S

2014-01-01

Purpose: Knowledge Based Radiation Therapy Treatment (KBRT) planning can be used to semi-automatically generate IMRT plans for new patients using constraints derived from previously manually-planned, geometrically similar patients. We investigate whether KBRT plans can achieve greater dose sparing than manual plans using optimized, organspecific constraint weighting factors. Methods: KBRT planning of HNC radiotherapy cases geometrically matched each new (query) case to one of the 105 clinically approved plans in our database. The dose distribution of the planned match was morphed to fit the querys geometry. Dose-volume constraints extracted from the morphed dose distribution were used to run the IMRT optimization with no user input. In the first version, all constraints were multiplied by a weighting factor of 0.7. The weighting factors were then systematically optimized (in order of OARs with increasing separation from the target) to maximize sparing to each OAR without compromising other OARs. The optimized, second version plans were compared against the first version plans and the clinically approved plans for 45 unilateral/bilateral target cases using the dose metrics: mean, median and maximum (brainstem and cord) doses. Results: Compared to the first version, the second version significantly reduced mean/median contralateral parotid doses (>2Gy) for bilateral cases. Other changes between the two versions were not clinically meaningful. Compared to the original clinical plans, both bilateral and unilateral plans in the second version had lower average dose metrics for 5 of the 6 OARs. Compared to the original plans, the second version achieved dose sparing that was at least as good for all OARs and better for the ipsilateral parotid (bilateral) and oral cavity (bilateral/unilateral). Differences in planning target volume coverage metrics were not clinically significant. Conclusion: HNC-KBRT planning generated IMRT plans with at least equivalent dose sparing to

SU-E-T-357: Semi-Automated Knowledge-Based Radiation Therapy (KBRT) Planning for Head-And-Neck Cancer (HNC): Can KBRT Plans Achieve Better Results Than Manual Planning?

Energy Technology Data Exchange (ETDEWEB)

Lutzky, C; Grzetic, S; Lo, J; Das, S [Duke University Medical Center, Durham, NC (United States)

2014-06-01

Purpose: Knowledge Based Radiation Therapy Treatment (KBRT) planning can be used to semi-automatically generate IMRT plans for new patients using constraints derived from previously manually-planned, geometrically similar patients. We investigate whether KBRT plans can achieve greater dose sparing than manual plans using optimized, organspecific constraint weighting factors. Methods: KBRT planning of HNC radiotherapy cases geometrically matched each new (query) case to one of the 105 clinically approved plans in our database. The dose distribution of the planned match was morphed to fit the querys geometry. Dose-volume constraints extracted from the morphed dose distribution were used to run the IMRT optimization with no user input. In the first version, all constraints were multiplied by a weighting factor of 0.7. The weighting factors were then systematically optimized (in order of OARs with increasing separation from the target) to maximize sparing to each OAR without compromising other OARs. The optimized, second version plans were compared against the first version plans and the clinically approved plans for 45 unilateral/bilateral target cases using the dose metrics: mean, median and maximum (brainstem and cord) doses. Results: Compared to the first version, the second version significantly reduced mean/median contralateral parotid doses (>2Gy) for bilateral cases. Other changes between the two versions were not clinically meaningful. Compared to the original clinical plans, both bilateral and unilateral plans in the second version had lower average dose metrics for 5 of the 6 OARs. Compared to the original plans, the second version achieved dose sparing that was at least as good for all OARs and better for the ipsilateral parotid (bilateral) and oral cavity (bilateral/unilateral). Differences in planning target volume coverage metrics were not clinically significant. Conclusion: HNC-KBRT planning generated IMRT plans with at least equivalent dose sparing to

Psychometric Quality of the Dutch Version of the Children's Eating Attitude Test in a Community Sample and a Sample of Overweight Youngsters

Directory of Open Access Journals (Sweden)

Lotte Theuwis

2010-12-01

Full Text Available Introduction. Disturbed eating attitudes may be important precursors of pathological eating patterns and, therefore need to be researched adequately. The Children's Eating Attitude Test (ChEAT is indicated for detecting at-risk attitudes and concerns in youngsters. Method. The present study was designed to provide a preliminary psychometric evaluation of the Dutch version of the ChEAT, by examining reliability and validity in a sample of 166 youngsters. Results. Generally the ChEAT seems to be a reliable instrument. Concurrent validity was demonstrated by positive correlations with measures assessing pathological eating behaviour and with related psychological problems. The discriminant validity was good. Based on ChEAT scores we can distinguish overweight youngsters from the community sample and “dieters” from “non dieters”. Divergent validity and factor structure show still shortcomings. Discussion. The Dutch version of the ChEAT seems to be a promising screening- and research instrument. Future prospective research could focus on a cut-off score for identifying at-risk youngsters.

Tank 241-BY-105 rotary core sampling and analysis plan

International Nuclear Information System (INIS)

Sasaki, L.M.

1995-01-01

This Sampling and Analysis Plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for two rotary-mode core samples from tank 241-BY-105 (BY-105)

105-DR Large Sodium Fire Facility decontamination, sampling, and analysis plan

International Nuclear Information System (INIS)

Knaus, Z.C.

1995-01-01

This is the decontamination, sampling, and analysis plan for the closure activities at the 105-DR Large Sodium Fire Facility at Hanford Reservation. This document supports the 105-DR Large Sodium Fire Facility Closure Plan, DOE-RL-90-25. The 105-DR LSFF, which operated from about 1972 to 1986, was a research laboratory that occupied the former ventilation supply room on the southwest side of the 105-DR Reactor facility in the 100-D Area of the Hanford Site. The LSFF was established to investigate fire fighting and safety associated with alkali metal fires in the liquid metal fast breeder reactor facilities. The decontamination, sampling, and analysis plan identifies the decontamination procedures, sampling locations, any special handling requirements, quality control samples, required chemical analysis, and data validation needed to meet the requirements of the 105-DR Large Sodium Fire Facility Closure Plan in compliance with the Resource Conservation and Recovery Act

Reachable Distance Space: Efficient Sampling-Based Planning for Spatially Constrained Systems

KAUST Repository

Xinyu Tang,

2010-01-25

Motion planning for spatially constrained robots is difficult due to additional constraints placed on the robot, such as closure constraints for closed chains or requirements on end-effector placement for articulated linkages. It is usually computationally too expensive to apply sampling-based planners to these problems since it is difficult to generate valid configurations. We overcome this challenge by redefining the robot\\'s degrees of freedom and constraints into a new set of parameters, called reachable distance space (RD-space), in which all configurations lie in the set of constraint-satisfying subspaces. This enables us to directly sample the constrained subspaces with complexity linear in the number of the robot\\'s degrees of freedom. In addition to supporting efficient sampling of configurations, we show that the RD-space formulation naturally supports planning and, in particular, we design a local planner suitable for use by sampling-based planners. We demonstrate the effectiveness and efficiency of our approach for several systems including closed chain planning with multiple loops, restricted end-effector sampling, and on-line planning for drawing/sculpting. We can sample single-loop closed chain systems with 1,000 links in time comparable to open chain sampling, and we can generate samples for 1,000-link multi-loop systems of varying topologies in less than a second. © 2010 The Author(s).

Sampling plans in attribute mode with multiple levels of precision

International Nuclear Information System (INIS)

Franklin, M.

1986-01-01

This paper describes a method for deriving sampling plans for nuclear material inventory verification. The method presented is different from the classical approach which envisages two levels of measurement precision corresponding to NDA and DA. In the classical approach the precisions of the two measurement methods are taken as fixed parameters. The new approach is based on multiple levels of measurement precision. The design of the sampling plan consists of choosing the number of measurement levels, the measurement precision to be used at each level and the sample size to be used at each level

Sampling and Analysis Plan for PUREX canyon vessel flushing

International Nuclear Information System (INIS)

Villalobos, C.N.

1995-01-01

A sampling and analysis plan is necessary to provide direction for the sampling and analytical activities determined by the data quality objectives. This document defines the sampling and analysis necessary to support the deactivation of the Plutonium-Uranium Extraction (PUREX) facility vessels that are regulated pursuant to Washington Administrative Code 173-303

UMTRA water sampling and analysis plan, Tuba City, Arizona

International Nuclear Information System (INIS)

1993-09-01

The purpose of this document is to provide background, guidance, and justification for fiscal year (FY) 1994 water sampling activities for the uranium mil tailings site at Tuba City, Arizona. This sampling and analysis plan will form the basis for groundwater sampling and analysis work orders to be implemented in FY94

Nonradioactive Dangerous Waste Landfill sampling and analysis plan and data quality objectives process summary report

International Nuclear Information System (INIS)

Smith, R.C.

1997-08-01

This sampling and analysis plan defines the sampling and analytical activities and associated procedures that will be used to support the Nonradioactive Dangerous Waste Landfill soil-gas investigation. This SAP consists of three sections: this introduction, the field sampling plan, and the quality assurance project plan. The field sampling plan defines the sampling and analytical methodologies to be performed

Background Information for the Nevada National Security Site Integrated Sampling Plan, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Farnham, Irene; Marutzky, Sam

2014-12-01

This document describes the process followed to develop the Nevada National Security Site (NNSS) Integrated Sampling Plan (referred to herein as the Plan). It provides the Plan’s purpose and objectives, and briefly describes the Underground Test Area (UGTA) Activity, including the conceptual model and regulatory requirements as they pertain to groundwater sampling. Background information on other NNSS groundwater monitoring programs—the Routine Radiological Environmental Monitoring Plan (RREMP) and Community Environmental Monitoring Program (CEMP)—and their integration with the Plan are presented. Descriptions of the evaluations, comments, and responses of two Sampling Plan topical committees are also included.

105-N Basin sediment disposition phase-one sampling and analysis plan

International Nuclear Information System (INIS)

1997-01-01

The sampling and analysis plan (SAP) for Phase 1 of the 105-N Basin sediment disposition project defines the sampling and analytical activities that will be performed for the engineering assessment phase (phase 1) of the project. A separate SAP defines the sampling and analytical activities that will be performed for the characterization phase (Phase 2) of the 105-N sediment disposition project. The Phase-1 SAP is presented in the introduction (Section 1.0), in the field sampling plan (FSP) (Section 2.0), and in the quality assurance project plan (QAPjP) (Section 3.0). The FSP defines the sampling and analytical methodologies to be performed. The QAPjP provides information on the quality assurance/quality control (QA/QC) parameters related to the sampling and analytical methodologies. This SAP defines the strategy and the methods that will be used to sample and analyze the sediment on the floor of the 105-N Basin. The resulting data will be used to develop and evaluate engineering designs for collecting and removing sediment from the basin

UMTRA Project water sampling and analysis plan, Durango, Colorado. Revision 1

International Nuclear Information System (INIS)

1995-09-01

Planned, routine ground water sampling activities at the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site in Durango, Colorado, are described in this water sampling and analysis plan. The plan identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the routine monitoring stations at the site. The ground water data are used to characterize the site ground water compliance strategies and to monitor contaminants of potential concern identified in the baseline risk assessment (DOE, 1995a). Regulatory basis for routine ground water monitoring at UMTRA Project sites is derived from the US EPA regulations in 40 CFR Part 192 (1994) and EPA standards of 1995 (60 FR 2854). Sampling procedures are guided by the UMTRA Project standard operating procedures (SOP) (JEG, n.d.), the Technical Approach Document (TAD) (DOE, 1989), and the most effective technical approach for the site

Hanford Sampling Quality Management Plan (HSQMP)

International Nuclear Information System (INIS)

Hyatt, J.E.

1995-01-01

This document provides a management tool for evaluating and designing the appropriate elements of a field sampling program. This document provides discussion of the elements of a program and is to be used as a guidance document during the preparation of project and/or function specific documentation. This document does not specify how a sampling program shall be organized. The HSQMP is to be used as a companion document to the Hanford Analytical Services Quality Assurance Plan (HASQAP) DOE/RL-94-55. The generation of this document was enhanced by conducting baseline evaluations of current sampling organizations. Valuable input was received from members of field and Quality Assurance organizations. The HSQMP is expected to be a living document. Revisions will be made as regulations and or Hanford Site conditions warrant changes in the best management practices. Appendices included are: summary of the sampling and analysis work flow process, a user's guide to the Data Quality Objective process, and a self-assessment checklist

Sampling and Analysis Plan for the 233-S Plutonium Concentration Facility

International Nuclear Information System (INIS)

Mihalic, M.A.

1998-02-01

This Sampling and Analysis Plan (SAP) provides the information and instructions to be used for sampling and analysis activities in the 233-S Plutonium Concentration Facility. The information and instructions herein are separated into three parts and address the Data Quality Objective (DQO) Summary Report, Quality Assurance Project Plan (QAP), and SAP

Tank 241-AP-104 Grab Sampling and Analysis Plan

International Nuclear Information System (INIS)

TEMPLETON, A.M.

2000-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AP-104. The purpose of this sampling event is to obtain information about the characteristics of the contents of 241-AP-104 required to provide sample material to the Waste Treatment Contractor. Grab samples will be obtained from riser 001 to provide sufficient material for the chemical analyses and tests required to satisfy these data quality objectives and ICD-23. The 222-S Laboratory will receive samples; composite the samples; perform chemical analyses on composite samples; and provide samples to the Waste Treatment Contractor and the Process Chemistry Laboratory. The Process Chemistry Laboratory at the 222-S Laboratory Complex will perform process tests to evaluate the behavior of the 241-AP-104 waste undergoing the retrieval and treatment scenarios defined in the applicable DQOs. The Waste Treatment Contractor will perform process verification and waste form qualification tests. Requirements for analyses of samples originating in the L and H DQO process tests will be documented in the corresponding test plan (Person 2000) and are not within the scope of this SAP. This report provides the general methodology and procedures to be used in the preparation, retrieval, transport, analysis, and reporting of results from grab samples retrieved from tank 241-AP-104

Energy-Aware Path Planning for UAS Persistent Sampling and Surveillance

Science.gov (United States)

Shaw-Cortez, Wenceslao

The focus of this work is to develop an energy-aware path planning algorithm that maximizes UAS endurance, while performing sampling and surveillance missions in a known, stationary wind environment. The energy-aware aspect is specifically tailored to extract energy from the wind to reduce thrust use, thereby increasing aircraft endurance. Wind energy extraction is performed by static soaring and dynamic soaring. Static soaring involves using upward wind currents to increase altitude and potential energy. Dynamic soaring involves taking advantage of wind gradients to exchange potential and kinetic energy. The path planning algorithm developed in this work uses optimization to combine these soaring trajectories with the overarching sampling and surveillance mission. The path planning algorithm uses a simplified aircraft model to tractably optimize soaring trajectories. This aircraft model is presented and along with the derivation of the equations of motion. A nonlinear program is used to create the soaring trajectories based on a given optimization problem. This optimization problem is defined using a heuristic decision tree, which defines appropriate problems given a sampling and surveillance mission and a wind model. Simulations are performed to assess the path planning algorithm. The results are used to identify properties of soaring trajectories as well as to determine what wind conditions support minimal thrust soaring. Additional results show how the path planning algorithm can be tuned between maximizing aircraft endurance and performing the sampling and surveillance mission. A means of trajectory stitching is demonstrated to show how the periodic soaring segments can be combined together to provide a full solution to an infinite/long horizon problem.

Mission Data System Java Edition Version 7

Science.gov (United States)

Reinholtz, William K.; Wagner, David A.

2013-01-01

The Mission Data System framework defines closed-loop control system abstractions from State Analysis including interfaces for state variables, goals, estimators, and controllers that can be adapted to implement a goal-oriented control system. The framework further provides an execution environment that includes a goal scheduler, execution engine, and fault monitor that support the expression of goal network activity plans. Using these frameworks, adapters can build a goal-oriented control system where activity coordination is verified before execution begins (plan time), and continually during execution. Plan failures including violations of safety constraints expressed in the plan can be handled through automatic re-planning. This version optimizes a number of key interfaces and features to minimize dependencies, performance overhead, and improve reliability. Fault diagnosis and real-time projection capabilities are incorporated. This version enhances earlier versions primarily through optimizations and quality improvements that raise the technology readiness level. Goals explicitly constrain system states over explicit time intervals to eliminate ambiguity about intent, as compared to command-oriented control that only implies persistent intent until another command is sent. A goal network scheduling and verification process ensures that all goals in the plan are achievable before starting execution. Goal failures at runtime can be detected (including predicted failures) and handled by adapted response logic. Responses can include plan repairs (try an alternate tactic to achieve the same goal), goal shedding, ignoring the fault, cancelling the plan, or safing the system.

Test plan for core sampling drill bit temperature monitor

International Nuclear Information System (INIS)

Francis, P.M.

1994-01-01

At WHC, one of the functions of the Tank Waste Remediation System division is sampling waste tanks to characterize their contents. The push-mode core sampling truck is currently used to take samples of liquid and sludge. Sampling of tanks containing hard salt cake is to be performed with the rotary-mode core sampling system, consisting of the core sample truck, mobile exhauster unit, and ancillary subsystems. When drilling through the salt cake material, friction and heat can be generated in the drill bit. Based upon tank safety reviews, it has been determined that the drill bit temperature must not exceed 180 C, due to the potential reactivity of tank contents at this temperature. Consequently, a drill bit temperature limit of 150 C was established for operation of the core sample truck to have an adequate margin of safety. Unpredictable factors, such as localized heating, cause this buffer to be so great. The most desirable safeguard against exceeding this threshold is bit temperature monitoring . This document describes the recommended plan for testing the prototype of a drill bit temperature monitor developed for core sampling by Sandia National Labs. The device will be tested at their facilities. This test plan documents the tests that Westinghouse Hanford Company considers necessary for effective testing of the system

Genesis Contingency Planning and Mishap Recovery: The Sample Curation View

Science.gov (United States)

Stansbery, E. K.; Allton, J. H.; Allen, C. C.; McNamara, K. M.; Calaway, M.; Rodriques, M. C.

2007-01-01

Planning for sample preservation and curation was part of mission design from the beginning. One of the scientific objectives for Genesis included collecting samples of three regimes of the solar wind in addition to collecting bulk solar wind during the mission. Collectors were fabricated in different thicknesses for each regime of the solar wind and attached to separate frames exposed to the solar wind during specific periods of solar activity associated with each regime. The original plan to determine the solar regime sampled for specific collectors was to identify to which frame the collector was attached. However, the collectors were dislodged during the hard landing making identification by frame attachment impossible. Because regimes were also identified by thickness of the collector, the regime sampled is identified by measuring fragment thickness. A variety of collector materials and thin films applied to substrates were selected and qualified for flight. This diversity provided elemental measurement in more than one material, mitigating effects of diffusion rates and/or radiation damage. It also mitigated against different material and substrate strengths resulting in differing effects of the hard landing. For example, silicon crystal substrates broke into smaller fragments than sapphire-based substrates and diamond surfaces were more resilient to flying debris damage than gold. The primary responsibility of the curation team for recovery was process documentation. Contingency planning for the recovery phase expanded this responsibility to include not only equipment to document, but also gather, contain and identify samples from the landing area and the recovered spacecraft. The team developed contingency plans for various scenarios as part of mission planning that included topographic maps to aid in site recovery and identification of different modes of transport and purge capability depending on damage. A clean tent, set-up at Utah Test & Training Range

Tank 241-U-105 push mode core sampling and analysis plan

International Nuclear Information System (INIS)

Bell, K.E.

1995-01-01

This Sampling and Analysis Plan (SAP) will identify characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for vapor samples and two push mode core samples from tank 241-U-105 (U-105)

Sampling and analysis plan for the 100-D Ponds voluntary remediation project

International Nuclear Information System (INIS)

1996-08-01

This Sampling and Analysis Plan (SAP) describes the sampling and analytical activities which will be performed to support closure of the 100-D Ponds Resource Conservation and Recovery Act (RCRA) treatment, storage, and/or disposal (TSD) unit. This SAP includes the Field Sampling Plan (FSP) presented in Section 2.0, and the Quality Assurance Project Plan (QAPjP) described in Section 3.0. The FSP defines the sampling and analytical methodologies to be performed, and the QAPjP provides or includes information on the requirements for precision, accuracy, representativeness, comparability, and completeness of the analytical data. This sampling and analysis plan was developed using the Environmental Protection Agency's Seven-Step Data Quality Objectives (DQO) Guidance (EPA, 1994). The purpose of the DQO meetings was (1) to identify the contaminants of concern and their cleanup levels under the Washington State Model Toxics Control Act (MTCA, WAC-173-340) Method B, and (2) to determine the number and locations of samples necessary to verify that the 100-D Ponds meet the cleanup criteria. The data collected will be used to support RCRA closure of this TSD unit

Evaluation of sampling plans for in-service inspection of steam generator tubes

International Nuclear Information System (INIS)

Kurtz, R.J.; Heasler, P.G.; Baird, D.B.

1994-02-01

This report summarizes the results of three previous studies to evaluate and compare the effectiveness of sampling plans for steam generator tube inspections. An analytical evaluation and Monte Carlo simulation techniques were the methods used to evaluate sampling plan performance. To test the performance of candidate sampling plans under a variety of conditions, ranges of inspection system reliability were considered along with different distributions of tube degradation. Results from the eddy current reliability studies performed with the retired-from-service Surry 2A steam generator were utilized to guide the selection of appropriate probability of detection and flaw sizing models for use in the analysis. Different distributions of tube degradation were selected to span the range of conditions that might exist in operating steam generators. The principal means of evaluating sampling performance was to determine the effectiveness of the sampling plan for detecting and plugging defective tubes. A summary of key results from the eddy current reliability studies is presented. The analytical and Monte Carlo simulation analyses are discussed along with a synopsis of key results and conclusions

RoadPlan Manual version 3.1

NARCIS (Netherlands)

Schoute, Albert L.

RoadPlan is an interactive planning and preprocessing tool to analyse and optimize multi-agv traffic. Currently it provides facilities for: * Traffic road map configuration and visualization; * Interactive drawing and modification of traffic layouts; * Collision and deadlock analysis of multiple

Preliminary Validation of a German Version of the Sexual Complaints Screener for Women in a Female Population Sample.

Science.gov (United States)

Burri, Andrea; Porst, Hartmut

2018-06-01

To date, neither the original English nor any of the translated versions of the Sexual Complaints Screener for Women (SCS-W) have been tested for their psychometric properties. To evaluate the validity and utility of the German version of the SCS-W by assessing content, convergent, and discriminant validity. A population sample of 309 women (mean age = 26.9 years) completed the online survey and had matching data available on the SCS-W and the Female Sexual Function Index (FSFI). Spearman bivariate correlations between the SCS-W and FSFI domain scores and exploratory factor analysis with principal component analysis were conducted. Convergent validity was excellent for the domain of orgasm, good for satisfaction, dyspareunia, and the total questionnaire score, and acceptable for desire, lubrication, arousal, and vaginismus. Discriminant validity was present for all domains apart from arousal, lubrication, and vaginismus. Varimax rotation suggested an 8-factor model was the most robust. This brief screener seems suitable to provide a brief overview of female patients' sexual problems in a clinical setting. This is the 1st study to assess the psychometric properties of the German version of the SCS-W. However, available information on the psychometric properties of the German SCS-W was limited because the validity of the screener could not be counterchecked against a clinical diagnosis of female sexual dysfunction. Our results provide preliminary evidence of good validity of the German version of the SCS-W. Overall, the SCS-W can offer support for clinicians who are less familiar with sexual medicine and who might not routinely discuss sexual issues with their patients. Burri A, Porst H. Preliminary Validation of a German Version of the Sexual Complaints Screener for Women in a Female Population Sample. Sex Med 2018;6:123-130. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

Sampling and Analysis Plan for the 221-U Facility

International Nuclear Information System (INIS)

Rugg, J.E.

1998-02-01

This sampling and analysis plan (SAP) presents the rationale and strategy for the sampling and analysis activities proposed to be conducted to support the evaluation of alternatives for the final disposition of the 221-U Facility. This SAP will describe general sample locations and the minimum number of samples required. It will also identify the specific contaminants of potential concern (COPCs) and the required analysis. This SAP does not define the exact sample locations and equipment to be used in the field due to the nature of unknowns associated with the 221-U Facility

Acceptance Sampling Plans Based on Truncated Life Tests for Sushila Distribution

Directory of Open Access Journals (Sweden)

Amer Ibrahim Al-Omari

2018-03-01

Full Text Available An acceptance sampling plan problem based on truncated life tests when the lifetime following a Sushila distribution is considered in this paper. For various acceptance numbers, confidence levels and values of the ratio between fixed experiment time and particular mean lifetime, the minimum sample sizes required to ascertain a specified mean life were found. The operating characteristic function values of the suggested sampling plans and the producer’s risk are presented. Some tables are provided and the results are illustrated by an example of a real data set.

Use of a brief version of the self-compassion inventory with an international sample of people with HIV/AIDS

OpenAIRE

Kemppainen, Jeanne K.; Brion, John M.; Leary, Mark; Wantland, Dean; Sullivan, K.; Nokes, Kathleen; Bain, Catherine A; Chaiphibalsarisdi, Puangtip; Chen, Wei-ti; Holzemer, William L.; Eller, Lucille Sanzero; Iipinge, Scholastika; Johnson, Mallory O.; Portillo, Carmen; Voss, Joachim

2013-01-01

The objective of this study was to extend the psychometric evaluation of a brief version of the Self Compassion Scale (SCS). A secondary analysis of data from an international sample of 1,967 English-speaking persons living with HIV disease was used to examine the factor structure, and reliability of the 12-item Brief Version Self Compassion Inventory (BVSCI). A Maximum Likelihood factor analysis and Oblimin with Kaiser Normalization confirmed a two-factor solution, accounting for 42.58% of t...

In situ sampling cart development engineering task plan

International Nuclear Information System (INIS)

DeFord, D.K.

1995-01-01

This Engineering Task Plan (ETP) supports the development for facility use of the next generation in situ sampling system for characterization of tank vapors. In situ sampling refers to placing sample collection devices (primarily sorbent tubes) directly into the tank headspace, then drawing tank gases through the collection devices to obtain samples. The current in situ sampling system is functional but was not designed to provide the accurate flow measurement required by today's data quality objectives (DQOs) for vapor characterization. The new system will incorporate modern instrumentation to achieve much tighter control. The next generation system will be referred to in this ETP as the New In Situ System (NISS) or New System. The report describes the current sampling system and the modifications that are required for more accuracy

Sampling Plans for the Thrips Frankliniella schultzei (Thysanoptera: Thripidae) in Three Lettuce Varieties.

Science.gov (United States)

Silva, Alisson R; Rodrigues-Silva, Nilson; Pereira, Poliana S; Sarmento, Renato A; Costa, Thiago L; Galdino, Tarcísio V S; Picanço, Marcelo C

2017-12-05

The common blossom thrips, Frankliniella schultzei Trybom (Thysanoptera: Thripidae), is an important lettuce pest worldwide. Conventional sampling plans are the first step in implementing decision-making systems into integrated pest management programs. However, this tool is not available for F. schultzei infesting lettuce crops. Thus, the objective of this work was to develop a conventional sampling plan for F. schultzei in lettuce crops. Two sampling techniques (direct counting and leaf beating on a white plastic tray) were compared in crisphead, looseleaf, and Boston lettuce varieties before and during head formation. The frequency distributions of F. schultzei densities in lettuce crops were assessed, and the number of samples required to compose the sampling plan was determined. Leaf beating on a white plastic tray was the best sampling technique. F. schultzei densities obtained with this technique were fitted to the negative binomial distribution with a common aggregation parameter (common K = 0.3143). The developed sampling plan is composed of 91 samples per field and presents low errors in its estimates (up to 20%), fast execution time (up to 47 min), and low cost (up to US $1.67 per sampling area). This sampling plan can be used as a tool for integrated pest management in lettuce crops, assisting with reliable decision making in different lettuce varieties before and during head formation. © The Author(s) 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Group SkSP-R sampling plan for accelerated life tests

Indian Academy of Sciences (India)

Muhammad Aslam

2017-09-15

Sep 15, 2017 ... SkSP-R sampling; life test; Weibull distribution; producer's risk; ... designed a sampling plan under a time-truncated life test .... adjusted using an acceleration factor. ... where P is the probability of lot acceptance for a single.

Designing a two-rank acceptance sampling plan for quality inspection of geospatial data products

Science.gov (United States)

Tong, Xiaohua; Wang, Zhenhua; Xie, Huan; Liang, Dan; Jiang, Zuoqin; Li, Jinchao; Li, Jun

2011-10-01

To address the disadvantages of classical sampling plans designed for traditional industrial products, we originally propose a two-rank acceptance sampling plan (TRASP) for the inspection of geospatial data outputs based on the acceptance quality level (AQL). The first rank sampling plan is to inspect the lot consisting of map sheets, and the second is to inspect the lot consisting of features in an individual map sheet. The TRASP design is formulated as an optimization problem with respect to sample size and acceptance number, which covers two lot size cases. The first case is for a small lot size with nonconformities being modeled by a hypergeometric distribution function, and the second is for a larger lot size with nonconformities being modeled by a Poisson distribution function. The proposed TRASP is illustrated through two empirical case studies. Our analysis demonstrates that: (1) the proposed TRASP provides a general approach for quality inspection of geospatial data outputs consisting of non-uniform items and (2) the proposed acceptance sampling plan based on TRASP performs better than other classical sampling plans. It overcomes the drawbacks of percent sampling, i.e., "strictness for large lot size, toleration for small lot size," and those of a national standard used specifically for industrial outputs, i.e., "lots with different sizes corresponding to the same sampling plan."

An Internationally Coordinated Science Management Plan for Samples Returned from Mars

Science.gov (United States)

Haltigin, T.; Smith, C. L.

2015-12-01

Mars Sample Return (MSR) remains a high priority of the planetary exploration community. Such an effort will undoubtedly be too large for any individual agency to conduct itself, and thus will require extensive global cooperation. To help prepare for an eventual MSR campaign, the International Mars Exploration Working Group (IMEWG) chartered the international Mars Architecture for the Return of Samples (iMARS) Phase II working group in 2014, consisting of representatives from 17 countries and agencies. The overarching task of the team was to provide recommendations for progressing towards campaign implementation, including a proposed science management plan. Building upon the iMARS Phase I (2008) outcomes, the Phase II team proposed the development of an International MSR Science Institute as part of the campaign governance, centering its deliberations around four themes: Organization: including an organizational structure for the Institute that outlines roles and responsibilities of key members and describes sample return facility requirements; Management: presenting issues surrounding scientific leadership, defining guidelines and assumptions for Institute membership, and proposing a possible funding model; Operations & Data: outlining a science implementation plan that details the preliminary sample examination flow, sample allocation process, and data policies; and Curation: introducing a sample curation plan that comprises sample tracking and routing procedures, sample sterilization considerations, and long-term archiving recommendations. This work presents a summary of the group's activities, findings, and recommendations, highlighting the role of international coordination in managing the returned samples.

The Kuder Skills Assessment-College and Adult Version: Development and Initial Validation in a College Business Sample

Science.gov (United States)

Rottinghaus, Patrick J.

2009-01-01

This article introduces the Kuder Skills Assessment-College and Adult version (KSA-CA; Rottinghaus, 2006), a new measure incorporating advances in the measurement of self-efficacy across 16 basic occupational domains (e.g., finance, information technology) and the six Kuder Clusters. Similar to the original development sample, all scales of the…

Sampling plan to support HLW tank 16

International Nuclear Information System (INIS)

Rodwell, P.O.; Martin, B.

1997-01-01

Plans are to remove the residual waste from the annulus of High-Level Waste Tank 16, located in the H-Area Tank Farm, in 1998. The interior of the tank is virtually clean. In the late 1970's, the waste was removed from the interior of the tank by several campaigns of waste removal with slurry pumps, spray washing, and oxalic acid cleaning. The annulus of the tank at one time had several thousand gallons of waste salt, which had leaked from the tank interior. Some of this salt was removed by adding water to the annulus and circulating, but much of the salt remains in the annulus. In order to confirm the source term used for fate and transport modeling, samples of the tank interior and annulus will be obtained and analyzed. If the results of the analyses indicate that the data used for the initial modeling is bounding then no changes will be made to the model. However, if the results indicate that the source term is higher than that assumed in the initial modeling, thus not bounding, additional modeling will be performed. The purpose of this Plan is to outline the approach to sampling the annulus and interior of Tank 16 as a prerequisite to salt removal in the annulus and closure of the entire tank system. The sampling and analysis of this tank system must be robust to reasonably ensure the actual tank residual is within the bounds of analysis error

Tank 241-AZ-102 Privatization Push Mode Core Sampling and Analysis Plan

International Nuclear Information System (INIS)

TEMPLETON, A.M.

1999-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AZ-102

Tank 241-AZ-102 Privatization Push Mode Core Sampling and Analysis Plan

International Nuclear Information System (INIS)

RASMUSSEN, J.H.

2000-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AZ-102

Abbreviated sampling and analysis plan for planning decontamination and decommissioning at Test Reactor Area (TRA) facilities

International Nuclear Information System (INIS)

1994-10-01

The objective is to sample and analyze for the presence of gamma emitting isotopes and hazardous constituents within certain areas of the Test Reactor Area (TRA), prior to D and D activities. The TRA is composed of three major reactor facilities and three smaller reactors built in support of programs studying the performance of reactor materials and components under high neutron flux conditions. The Materials Testing Reactor (MTR) and Engineering Test Reactor (ETR) facilities are currently pending D/D. Work consists of pre-D and D sampling of designated TRA (primarily ETR) process areas. This report addresses only a limited subset of the samples which will eventually be required to characterize MTR and ETR and plan their D and D. Sampling which is addressed in this document is intended to support planned D and D work which is funded at the present time. Biased samples, based on process knowledge and plant configuration, are to be performed. The multiple process areas which may be potentially sampled will be initially characterized by obtaining data for upstream source areas which, based on facility configuration, would affect downstream and as yet unsampled, process areas. Sampling and analysis will be conducted to determine the level of gamma emitting isotopes and hazardous constituents present in designated areas within buildings TRA-612, 642, 643, 644, 645, 647, 648, 663; and in the soils surrounding Facility TRA-611. These data will be used to plan the D and D and help determine disposition of material by D and D personnel. Both MTR and ETR facilities will eventually be decommissioned by total dismantlement so that the area can be restored to its original condition

Reliability, factor structure, and validity of the German version of the Trauma Symptom Checklist for Children in a sample of adolescents

Science.gov (United States)

Matulis, Simone; Loos, Laura; Langguth, Nadine; Schreiber, Franziska; Gutermann, Jana; Gawrilow, Caterina; Steil, Regina

2015-01-01

Background The Trauma Symptom Checklist for Children (TSC-C) is the most widely used self-report scale to assess trauma-related symptoms in children and adolescents on six clinical scales. The purpose of the present study was to develop a German version of the TSC-C and to investigate its psychometric properties, such as factor structure, reliability, and validity, in a sample of German adolescents. Method A normative sample of N=583 and a clinical sample of N=41 adolescents with a history of physical or sexual abuse aged between 13 and 21 years participated in the study. Results The Confirmatory Factor Analysis on the six-factor model (anger, anxiety, depression, dissociation, posttraumatic stress, and sexual concerns with the subdimensions preoccupation and distress) revealed acceptable to good fit statistics in the normative sample. One item had to be excluded from the German version of the TSC-C because the factor loading was too low. All clinical scales presented acceptable to good reliability, with Cronbach's α's ranging from .80 to .86 in the normative sample and from .72 to .87 in the clinical sample. Concurrent validity was also demonstrated by the high correlations between the TSC-C scales and instruments measuring similar psychopathology. TSC-C scores reliably differentiated between adolescents with trauma history and those without trauma history, indicating discriminative validity. Conclusions In conclusion, the German version of the TSC-C is a reliable and valid instrument for assessing trauma-related symptoms on six different scales in adolescents aged between 13 and 21 years. PMID:26498182

IP Sample Plan #5 | NCI Technology Transfer Center | TTC

Science.gov (United States)

A sample Intellectual Property Management Plan in the form of a legal agreement between a University and its collaborators which addresses data sharing, sharing of research tools and resources and intellectual property management.

Test plan for evaluating the performance of the in-tank fluidic sampling system

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

The PHMC will provide Low Activity Wastes (LAW) tank wastes for final treatment by a privatization contractor from double-shell feed tanks, 241-AP-102 and 241-AP-104, Concerns about the inability of the baseline ''grab'' sampling to provide large volume samples within time constraints has led to the development of a conceptual sampling system that would be deployed in a feed tank riser, This sampling system will provide large volume, representative samples without the environmental, radiation exposure, and sample volume impacts of the current base-line ''grab'' sampling method. This test plan identifies ''proof-of-principle'' cold tests for the conceptual sampling system using simulant materials. The need for additional testing was identified as a result of completing tests described in the revision test plan document, Revision 1 outlines tests that will evaluate the performance and ability to provide samples that are representative of a tanks' content within a 95 percent confidence interval, to recovery from plugging, to sample supernatant wastes with over 25 wt% solids content, and to evaluate the impact of sampling at different heights within the feed tank. The test plan also identifies operating parameters that will optimize the performance of the sampling system

Tank 241-AZ-102 Privatization Push Mode Core Sampling and Analysis Plan; FINAL

International Nuclear Information System (INIS)

TEMPLETON, A.M.

1999-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AZ-102. The purpose of this sampling event is to obtain information about the characteristics of the contents of 241-AZ-102. Push mode core samples will be obtained from risers 15C and 24A to provide sufficient material for the chemical analyses and tests required to satisfy these data quality objectives. The 222-S Laboratory will extrude core samples, composite the liquids and solids, perform chemical analyses, and provide subsamples to the Process Chemistry Laboratory. The Process Chemistry Laboratory will prepare test plans and perform process tests to evaluate the behavior of the 241-AZ-102 waste undergoing the retrieval and treatment scenarios defined in the applicable DQOs. Requirements for analyses of samples originating in the process tests will be documented in the corresponding test plan

Soil Sampling Plan for the transuranic storage area soil overburden and final report: Soil overburden sampling at the RWMC transuranic storage area

International Nuclear Information System (INIS)

Stanisich, S.N.

1994-12-01

This Soil Sampling Plan (SSP) has been developed to provide detailed procedural guidance for field sampling and chemical and radionuclide analysis of selected areas of soil covering waste stored at the Transuranic Storage Area (TSA) at the Idaho National Engineering Laboratory's (INEL) Radioactive Waste Management Complex (RWMC). The format and content of this SSP represents a complimentary hybrid of INEL Waste Management--Environmental Restoration Program, and Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) Remedial Investigation/Feasibility Study (RI/FS) sampling guidance documentation. This sampling plan also functions as a Quality Assurance Project Plan (QAPP). The QAPP as a controlling mechanism during sampling to ensure that all data collected are valid, reliabile, and defensible. This document outlines organization, objectives and quality assurance/quality control (QA/QC) activities to achieve the desired data quality goals. The QA/QC requirements for this project are outlined in the Data Collection Quality Assurance Plan (DCQAP) for the Buried Waste Program. The DCQAP is a program plan and does not outline the site specific requirements for the scope of work covered by this SSP

Spatial distribution and sequential sampling plans for Tuta absoluta (Lepidoptera: Gelechiidae) in greenhouse tomato crops.

Science.gov (United States)

Cocco, Arturo; Serra, Giuseppe; Lentini, Andrea; Deliperi, Salvatore; Delrio, Gavino

2015-09-01

The within- and between-plant distribution of the tomato leafminer, Tuta absoluta (Meyrick), was investigated in order to define action thresholds based on leaf infestation and to propose enumerative and binomial sequential sampling plans for pest management applications in protected crops. The pest spatial distribution was aggregated between plants, and median leaves were the most suitable sample to evaluate the pest density. Action thresholds of 36 and 48%, 43 and 56% and 60 and 73% infested leaves, corresponding to economic thresholds of 1 and 3% damaged fruits, were defined for tomato cultivars with big, medium and small fruits respectively. Green's method was a more suitable enumerative sampling plan as it required a lower sampling effort. Binomial sampling plans needed lower average sample sizes than enumerative plans to make a treatment decision, with probabilities of error of sampling plan required 87 or 343 leaves to estimate the population density in extensive or intensive ecological studies respectively. Binomial plans would be more practical and efficient for control purposes, needing average sample sizes of 17, 20 and 14 leaves to take a pest management decision in order to avoid fruit damage higher than 1% in cultivars with big, medium and small fruits respectively. © 2014 Society of Chemical Industry.

Preliminary Validation of a German Version of the Sexual Complaints Screener for Women in a Female Population Sample

Directory of Open Access Journals (Sweden)

Andrea Burri, DrSc

2018-06-01

Full Text Available Background: To date, neither the original English nor any of the translated versions of the Sexual Complaints Screener for Women (SCS-W have been tested for their psychometric properties. Aim: To evaluate the validity and utility of the German version of the SCS-W by assessing content, convergent, and discriminant validity. Methods: A population sample of 309 women (mean age = 26.9 years completed the online survey and had matching data available on the SCS-W and the Female Sexual Function Index (FSFI. Spearman bivariate correlations between the SCS-W and FSFI domain scores and exploratory factor analysis with principal component analysis were conducted. Outcomes: Convergent validity was excellent for the domain of orgasm, good for satisfaction, dyspareunia, and the total questionnaire score, and acceptable for desire, lubrication, arousal, and vaginismus. Discriminant validity was present for all domains apart from arousal, lubrication, and vaginismus. Varimax rotation suggested an 8-factor model was the most robust. Clinical Implications: This brief screener seems suitable to provide a brief overview of female patients' sexual problems in a clinical setting. Strengths and Limitations: This is the 1st study to assess the psychometric properties of the German version of the SCS-W. However, available information on the psychometric properties of the German SCS-W was limited because the validity of the screener could not be counterchecked against a clinical diagnosis of female sexual dysfunction. Conclusion: Our results provide preliminary evidence of good validity of the German version of the SCS-W. Overall, the SCS-W can offer support for clinicians who are less familiar with sexual medicine and who might not routinely discuss sexual issues with their patients.Burri A, Porst H. Preliminary Validation of a German Version of the Sexual Complaints Screener for Women in a Female Population Sample. Sex Med 2018;6:123–130. Key Words: Female Sexual

Visual Sample Plan (VSP) - FIELDS Integration

Energy Technology Data Exchange (ETDEWEB)

Pulsipher, Brent A.; Wilson, John E.; Gilbert, Richard O.; Hassig, Nancy L.; Carlson, Deborah K.; Bing-Canar, John; Cooper, Brian; Roth, Chuck

2003-04-19

Two software packages, VSP 2.1 and FIELDS 3.5, are being used by environmental scientists to plan the number and type of samples required to meet project objectives, display those samples on maps, query a database of past sample results, produce spatial models of the data, and analyze the data in order to arrive at defensible decisions. VSP 2.0 is an interactive tool to calculate optimal sample size and optimal sample location based on user goals, risk tolerance, and variability in the environment and in lab methods. FIELDS 3.0 is a set of tools to explore the sample results in a variety of ways to make defensible decisions with quantified levels of risk and uncertainty. However, FIELDS 3.0 has a small sample design module. VSP 2.0, on the other hand, has over 20 sampling goals, allowing the user to input site-specific assumptions such as non-normality of sample results, separate variability between field and laboratory measurements, make two-sample comparisons, perform confidence interval estimation, use sequential search sampling methods, and much more. Over 1,000 copies of VSP are in use today. FIELDS is used in nine of the ten U.S. EPA regions, by state regulatory agencies, and most recently by several international countries. Both software packages have been peer-reviewed, enjoy broad usage, and have been accepted by regulatory agencies as well as site project managers as key tools to help collect data and make environmental cleanup decisions. Recently, the two software packages were integrated, allowing the user to take advantage of the many design options of VSP, and the analysis and modeling options of FIELDS. The transition between the two is simple for the user – VSP can be called from within FIELDS, automatically passing a map to VSP and automatically retrieving sample locations and design information when the user returns to FIELDS. This paper will describe the integration, give a demonstration of the integrated package, and give users download

Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites

International Nuclear Information System (INIS)

2012-01-01

This plan incorporates U.S. Department of Energy (DOE) Office of Legacy Management (LM) standard operating procedures (SOPs) into environmental monitoring activities and will be implemented at all sites managed by LM. This document provides detailed procedures for the field sampling teams so that samples are collected in a consistent and technically defensible manner. Site-specific plans (e.g., long-term surveillance and maintenance plans, environmental monitoring plans) document background information and establish the basis for sampling and monitoring activities. Information will be included in site-specific tabbed sections to this plan, which identify sample locations, sample frequencies, types of samples, field measurements, and associated analytes for each site. Additionally, within each tabbed section, program directives will be included, when developed, to establish additional site-specific requirements to modify or clarify requirements in this plan as they apply to the corresponding site. A flowchart detailing project tasks required to accomplish routine sampling is displayed in Figure 1. LM environmental procedures are contained in the Environmental Procedures Catalog (LMS/PRO/S04325), which incorporates American Society for Testing and Materials (ASTM), DOE, and U.S. Environmental Protection Agency (EPA) guidance. Specific procedures used for groundwater and surface water monitoring are included in Appendix A. If other environmental media are monitored, SOPs used for air, soil/sediment, and biota monitoring can be found in the site-specific tabbed sections in Appendix D or in site-specific documents. The procedures in the Environmental Procedures Catalog are intended as general guidance and require additional detail from planning documents in order to be complete; the following sections fulfill that function and specify additional procedural requirements to form SOPs. Routine revision of this Sampling and Analysis Plan will be conducted annually at the

Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites

Energy Technology Data Exchange (ETDEWEB)

None

2012-10-24

This plan incorporates U.S. Department of Energy (DOE) Office of Legacy Management (LM) standard operating procedures (SOPs) into environmental monitoring activities and will be implemented at all sites managed by LM. This document provides detailed procedures for the field sampling teams so that samples are collected in a consistent and technically defensible manner. Site-specific plans (e.g., long-term surveillance and maintenance plans, environmental monitoring plans) document background information and establish the basis for sampling and monitoring activities. Information will be included in site-specific tabbed sections to this plan, which identify sample locations, sample frequencies, types of samples, field measurements, and associated analytes for each site. Additionally, within each tabbed section, program directives will be included, when developed, to establish additional site-specific requirements to modify or clarify requirements in this plan as they apply to the corresponding site. A flowchart detailing project tasks required to accomplish routine sampling is displayed in Figure 1. LM environmental procedures are contained in the Environmental Procedures Catalog (LMS/PRO/S04325), which incorporates American Society for Testing and Materials (ASTM), DOE, and U.S. Environmental Protection Agency (EPA) guidance. Specific procedures used for groundwater and surface water monitoring are included in Appendix A. If other environmental media are monitored, SOPs used for air, soil/sediment, and biota monitoring can be found in the site-specific tabbed sections in Appendix D or in site-specific documents. The procedures in the Environmental Procedures Catalog are intended as general guidance and require additional detail from planning documents in order to be complete; the following sections fulfill that function and specify additional procedural requirements to form SOPs. Routine revision of this Sampling and Analysis Plan will be conducted annually at the

Sequential Sampling Plan of Anthonomus grandis (Coleoptera: Curculionidae) in Cotton Plants.

Science.gov (United States)

Grigolli, J F J; Souza, L A; Mota, T A; Fernandes, M G; Busoli, A C

2017-04-01

The boll weevil, Anthonomus grandis grandis Boheman (Coleoptera: Curculionidae), is one of the most important pests of cotton production worldwide. The objective of this work was to develop a sequential sampling plan for the boll weevil. The studies were conducted in Maracaju, MS, Brazil, in two seasons with cotton cultivar FM 993. A 10,000-m2 area of cotton was subdivided into 100 of 10- by 10-m plots, and five plants per plot were evaluated weekly, recording the number of squares with feeding + oviposition punctures of A. grandis in each plant. A sequential sampling plan by the maximum likelihood ratio test was developed, using a 10% threshold level of squares attacked. A 5% security level was adopted for the elaboration of the sequential sampling plan. The type I and type II error used was 0.05, recommended for studies with insects. The adjustment of the frequency distributions used were divided into two phases, so that the model that best fit to the data was the negative binomial distribution up to 85 DAE (Phase I), and from there the best fit was Poisson distribution (Phase II). The equations that define the decision-making for Phase I are S0 = -5.1743 + 0.5730N and S1 = 5.1743 + 0.5730N, and for the Phase II are S0 = -4.2479 + 0.5771N and S1 = 4.2479 + 0.5771N. The sequential sampling plan developed indicated the maximum number of sample units expected for decision-making is ∼39 and 31 samples for Phases I and II, respectively. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Versioning of printed products

Science.gov (United States)

Tuijn, Chris

2005-01-01

During the definition of a printed product in an MIS system, a lot of attention is paid to the production process. The MIS systems typically gather all process-related parameters at such a level of detail that they can determine what the exact cost will be to make a specific product. This information can then be used to make a quote for the customer. Considerably less attention is paid to the content of the products since this does not have an immediate impact on the production costs (assuming that the number of inks or plates is known in advance). The content management is typically carried out either by the prepress systems themselves or by dedicated workflow servers uniting all people that contribute to the manufacturing of a printed product. Special care must be taken when considering versioned products. With versioned products we here mean distinct products that have a number of pages or page layers in common. Typical examples are comic books that have to be printed in different languages. In this case, the color plates can be shared over the different versions and the black plate will be different. Other examples are nation-wide magazines or newspapers that have an area with regional pages or advertising leaflets in different languages or currencies. When considering versioned products, the content will become an important cost factor. First of all, the content management (and associated proofing and approval cycles) becomes much more complex and, therefore, the risk that mistakes will be made increases considerably. Secondly, the real production costs are very much content-dependent because the content will determine whether plates can be shared across different versions or not and how many press runs will be needed. In this paper, we will present a way to manage different versions of a printed product. First, we will introduce a data model for version management. Next, we will show how the content of the different versions can be supplied by the customer

A scalable method for parallelizing sampling-based motion planning algorithms

KAUST Repository

Jacobs, Sam Ade; Manavi, Kasra; Burgos, Juan; Denny, Jory; Thomas, Shawna; Amato, Nancy M.

2012-01-01

This paper describes a scalable method for parallelizing sampling-based motion planning algorithms. It subdivides configuration space (C-space) into (possibly overlapping) regions and independently, in parallel, uses standard (sequential) sampling-based planners to construct roadmaps in each region. Next, in parallel, regional roadmaps in adjacent regions are connected to form a global roadmap. By subdividing the space and restricting the locality of connection attempts, we reduce the work and inter-processor communication associated with nearest neighbor calculation, a critical bottleneck for scalability in existing parallel motion planning methods. We show that our method is general enough to handle a variety of planning schemes, including the widely used Probabilistic Roadmap (PRM) and Rapidly-exploring Random Trees (RRT) algorithms. We compare our approach to two other existing parallel algorithms and demonstrate that our approach achieves better and more scalable performance. Our approach achieves almost linear scalability on a 2400 core LINUX cluster and on a 153,216 core Cray XE6 petascale machine. © 2012 IEEE.

A scalable method for parallelizing sampling-based motion planning algorithms

KAUST Repository

Jacobs, Sam Ade

2012-05-01

This paper describes a scalable method for parallelizing sampling-based motion planning algorithms. It subdivides configuration space (C-space) into (possibly overlapping) regions and independently, in parallel, uses standard (sequential) sampling-based planners to construct roadmaps in each region. Next, in parallel, regional roadmaps in adjacent regions are connected to form a global roadmap. By subdividing the space and restricting the locality of connection attempts, we reduce the work and inter-processor communication associated with nearest neighbor calculation, a critical bottleneck for scalability in existing parallel motion planning methods. We show that our method is general enough to handle a variety of planning schemes, including the widely used Probabilistic Roadmap (PRM) and Rapidly-exploring Random Trees (RRT) algorithms. We compare our approach to two other existing parallel algorithms and demonstrate that our approach achieves better and more scalable performance. Our approach achieves almost linear scalability on a 2400 core LINUX cluster and on a 153,216 core Cray XE6 petascale machine. © 2012 IEEE.

Spatial Distribution and Sampling Plans for Grapevine Plant Canopy-Inhabiting Scaphoideus titanus (Hemiptera: Cicadellidae) Nymphs.

Science.gov (United States)

Rigamonti, Ivo E; Brambilla, Carla; Colleoni, Emanuele; Jermini, Mauro; Trivellone, Valeria; Baumgärtner, Johann

2016-04-01

The paper deals with the study of the spatial distribution and the design of sampling plans for estimating nymph densities of the grape leafhopper Scaphoideus titanus Ball in vine plant canopies. In a reference vineyard sampled for model parameterization, leaf samples were repeatedly taken according to a multistage, stratified, random sampling procedure, and data were subjected to an ANOVA. There were no significant differences in density neither among the strata within the vineyard nor between the two strata with basal and apical leaves. The significant differences between densities on trunk and productive shoots led to the adoption of two-stage (leaves and plants) and three-stage (leaves, shoots, and plants) sampling plans for trunk shoots- and productive shoots-inhabiting individuals, respectively. The mean crowding to mean relationship used to analyze the nymphs spatial distribution revealed aggregated distributions. In both the enumerative and the sequential enumerative sampling plans, the number of leaves of trunk shoots, and of leaves and shoots of productive shoots, was kept constant while the number of plants varied. In additional vineyards data were collected and used to test the applicability of the distribution model and the sampling plans. The tests confirmed the applicability 1) of the mean crowding to mean regression model on the plant and leaf stages for representing trunk shoot-inhabiting distributions, and on the plant, shoot, and leaf stages for productive shoot-inhabiting nymphs, 2) of the enumerative sampling plan, and 3) of the sequential enumerative sampling plan. In general, sequential enumerative sampling was more cost efficient than enumerative sampling.

Sampling and Analysis Plan for K Basins Debris

International Nuclear Information System (INIS)

WESTCOTT, J.L.

2000-01-01

This Sampling and Analysis Plan presents the rationale and strategy for sampling and analysis activities to support removal of debris from the K-East and K-West Basins located in the 100K Area at the Hanford Site. This project is focused on characterization to support waste designation for disposal of waste at the Environmental Restoration Disposal Facility (ERDF). This material has previously been dispositioned at the Hanford Low-Level Burial Grounds or Central Waste Complex. The structures that house the basins are classified as radioactive material areas. Therefore, all materials removed from the buildings are presumed to be radioactively contaminated. Because most of the materials that will be addressed under this plan will be removed from the basins, and because of the cost associated with screening materials for release, it is anticipated that all debris will be managed as low-level waste. Materials will be surveyed, however, to estimate radionuclide content for disposal and to determine that the debris is not contaminated with levels of transuranic radionuclides that would designate the debris as transuranic waste

Sampling and Analysis Plan for the 216-A-29 Ditch

International Nuclear Information System (INIS)

Petersen, S.W.

1998-06-01

This sampling and analysis plan defines procedures to be used for collecting and handling samples to be obtained from the 216-A-29 Ditch, and identifies requirements for field and laboratory measurements. The sampling strategy describes here is derived from a Data Quality Objectives workshop conducted in January 1997 to support sampling to assure worker safety during construction and to assess the validity of a 1988 ditch sampling campaign and the effectiveness of subsequent stabilization. The purpose of the proposed sampling and analysis activities is to characterize soil contamination in the vicinity of a proposed road over the 216-A-29 Ditch

Sampling and analysis plan for the former Atomic Energy Commission bus lot property

International Nuclear Information System (INIS)

Nielson, R.R.

1998-07-01

This sampling and analysis plan (SAP) presents the rationale and strategy for the sampling and analysis activities proposed in support of an initial investigation of the former Atomic Energy Commission (AEC) bus lot property currently owned by Battelle Memorial Institute. The purpose of the proposed sampling and analysis activity is to investigate the potential for contamination above established action levels. The SAP will provide defensible data of sufficient quality and quantity to support recommendations of whether any further action within the study area is warranted. To assist in preparing sampling plans and reports, the Washington State Department of Ecology (Ecology) has published Guidance on Sampling and Data Analysis Methods. To specifically address sampling plans for petroleum-contaminated sites, Ecology has also published Guidance for Remediation of Petroleum Contaminated Sites. Both documents were used as guidance in preparing this plan. In 1992, a soil sample was taken within the current study area as part of a project to remove two underground storage tanks (USTs) at Battelle's Sixth Street Warehouse Petroleum Dispensing Station (Section 1.3). The results showed that the sample contained elevated levels of total petroleum hydrocarbons (TPH) in the heavy distillate range. This current study was initiated in part as a result of that discovery. The following topics are considered: the historical background of the site, current site conditions, previous investigations performed at the site, an evaluation based on the available data, and the contaminants of potential concern (COPC)

Sampling and analysis plan for the former Atomic Energy Commission bus lot property

Energy Technology Data Exchange (ETDEWEB)

Nielson, R.R.

1998-07-01

This sampling and analysis plan (SAP) presents the rationale and strategy for the sampling and analysis activities proposed in support of an initial investigation of the former Atomic Energy Commission (AEC) bus lot property currently owned by Battelle Memorial Institute. The purpose of the proposed sampling and analysis activity is to investigate the potential for contamination above established action levels. The SAP will provide defensible data of sufficient quality and quantity to support recommendations of whether any further action within the study area is warranted. To assist in preparing sampling plans and reports, the Washington State Department of Ecology (Ecology) has published Guidance on Sampling and Data Analysis Methods. To specifically address sampling plans for petroleum-contaminated sites, Ecology has also published Guidance for Remediation of Petroleum Contaminated Sites. Both documents were used as guidance in preparing this plan. In 1992, a soil sample was taken within the current study area as part of a project to remove two underground storage tanks (USTs) at Battelle`s Sixth Street Warehouse Petroleum Dispensing Station (Section 1.3). The results showed that the sample contained elevated levels of total petroleum hydrocarbons (TPH) in the heavy distillate range. This current study was initiated in part as a result of that discovery. The following topics are considered: the historical background of the site, current site conditions, previous investigations performed at the site, an evaluation based on the available data, and the contaminants of potential concern (COPC).

IP Sample Plan #1 | NCI Technology Transfer Center | TTC

Science.gov (United States)

Sample letter that shows how Universities including co-investigators, consultants, and collaborators can describe a data and research tool sharing plan and procedures for exercising intellectual property rights. The letter is to be used as part of the University's application. 

Ground-water sample collection and analysis plan for the ground-water surveillance project

International Nuclear Information System (INIS)

Bryce, R.W.; Evans, J.C.; Olsen, K.B.

1991-12-01

The Pacific Northwest Laboratory performs ground-water sampling activities at the US Department of Energy's (DOE's) Hanford Site in support of DOE's environmental surveillance responsibilities. The purpose of this document is to translate DOE's General Environmental Protection Program (DOE Order 5400.1) into a comprehensive ground-water sample collection and analysis plan for the Hanford Site. This sample collection and analysis plan sets forth the environmental surveillance objectives applicable to ground water, identifies the strategy for selecting sample collection locations, and lists the analyses to be performed to meet those objectives

Liquid effluent Sampling and Analysis Plan (SAP) implementation summary report

International Nuclear Information System (INIS)

Lueck, K.J.

1995-01-01

This report summarizes liquid effluent analytical data collected during the Sampling and Analysis Plan (SAP) Implementation Program, evaluates whether or not the sampling performed meets the requirements of the individual SAPs, compares the results to the WAC 173-200 Ground Water Quality Standards. Presented in the report are results from liquid effluent samples collected (1992-1994) from 18 of the 22 streams identified in the Consent Order (No. DE 91NM-177) requiring SAPs

Planning Considerations Related to Collecting and Analyzing Samples of the Martian Soils

Science.gov (United States)

Liu, Yang; Mellon, Mike T.; Ming, Douglas W.; Morris, Richard V.; Noble, Sarah K.; Sullivan, Robert J.; Taylor, Lawrence A.; Beaty, David W.

2014-01-01

The Mars Sample Return (MSR) End-to-End International Science Analysis Group (E2E-iSAG [1]) established scientific objectives associ-ated with Mars returned-sample science that require the return and investigation of one or more soil samples. Soil is defined here as loose, unconsolidated materials with no implication for the presence or absence of or-ganic components. The proposed Mars 2020 (M-2020) rover is likely to collect and cache soil in addition to rock samples [2], which could be followed by future sample retrieval and return missions. Here we discuss key scientific consid-erations for sampling and caching soil samples on the proposed M-2020 rover, as well as the state in which samples would need to be preserved when received by analysts on Earth. We are seeking feedback on these draft plans as input to mission requirement formulation. A related planning exercise on rocks is reported in an accompanying abstract [3].

IP Sample Plan #3 | NCI Technology Transfer Center | TTC

Science.gov (United States)

Sample Research Resources and Intellectual Property Plan for use by an Institution and its Collaborators for intellectual property protection strategies covering pre-existing intellectual property, agreements with commercial sources, privacy, and licensing.  | [google6f4cd5334ac394ab.html

UMTRA Project water sampling and analysis plan, Canonsburg, Pennsylvania. Revision 1

International Nuclear Information System (INIS)

1995-09-01

Surface remedial action was completed at the US Department of Energy (DOE) Canonsburg and Burrell Uranium Mill Tailings Remedial Action (UMTRA) Project sites in southwestern Pennsylvania in 1985 and 1987, respectively. The Burrell disposal site, included in the UMTRA Project as a vicinity property, was remediated in conjunction with the remedial action at Canonsburg. On 27 May 1994, the Nuclear Regulatory Commission (NRC) accepted the DOE final Long-Term Surveillance Plan (LTSP) (DOE, 1993) for Burrell thus establishing the site under the general license in 10 CFR section 40.27 (1994). In accordance with the DOE guidance document for long-term surveillance (DOE, 1995), all NRC/DOE interaction on the Burrell site's long-term care now is conducted with the DOE Grand Junction Projects Office in Grand Junction, Colorado, and is no longer the responsibility of the DOE UMTRA Project Team in Albuquerque, New Mexico. Therefore, the planned sampling activities described in this water sampling and analysis plan (WSAP) are limited to the Canonsburg site. This WSAP identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequencies for routine monitoring at the Canonsburg site for calendar years 1995 and 1996. Currently, the analytical data further the site characterization and demonstrate that the disposal cell's initial performance is in accordance with design requirements

Sampling and analysis plan for Wayne Interim Storage Site (WISS), Wayne, New Jersey

International Nuclear Information System (INIS)

Brown, K.S.; Murray, M.E.; Rodriguez, R.E.

1998-10-01

This field sampling plan describes the methodology to perform an independent radiological verification survey and chemical characterization of a remediated area of the subpile at the Wayne Interim Storage Site, Wayne, New Jersey.Data obtained from collection and analysis of systematic and biased soil samples will be used to assess the status of remediation at the site and verify the final radiological status. The objective of this plan is to describe the methods for obtaining sufficient and valid measurements and analytical data to supplement and verify a radiological profile already established by the Project Remediation Management Contractor (PMC). The plan describes the procedure for obtaining sufficient and valid analytical data on soil samples following remediation of the first layer of the subpile. Samples will be taken from an area of the subpile measuring approximately 30 m by 80 m from which soil has been excavated to a depth of approximately 20 feet to confirm that the soil beneath the excavated area does not exceed radiological guidelines established for the site or chemical regulatory limits for inorganic metals. After the WISS has been fully remediated, the Department of Energy will release it for industrial/commercial land use in accordance with the Record of Decision. This plan provides supplemental instructions to guidelines and procedures established for sampling and analysis activities. Procedures will be referenced throughout this plan as applicable, and are available for review if necessary

ASPEN Version 3.0

Science.gov (United States)

Rabideau, Gregg; Chien, Steve; Knight, Russell; Schaffer, Steven; Tran, Daniel; Cichy, Benjamin; Sherwood, Robert

2006-01-01

The Automated Scheduling and Planning Environment (ASPEN) computer program has been updated to version 3.0. ASPEN is a modular, reconfigurable, application software framework for solving batch problems that involve reasoning about time, activities, states, and resources. Applications of ASPEN can include planning spacecraft missions, scheduling of personnel, and managing supply chains, inventories, and production lines. ASPEN 3.0 can be customized for a wide range of applications and for a variety of computing environments that include various central processing units and random access memories.

IP Sample Plan #4 | NCI Technology Transfer Center | TTC

Science.gov (United States)

Sample letter from Research Institutes and their principal investigator and consultants, describing a data and research tool sharing plan and procedures for sharing data, research materials, and patent and licensing of intellectual property. This letter is designed to be included as part of an application.

Reliability and Construct Validity of the Dutch Psychopathy Checklist: Youth Version--Findings from a Sample of Male Adolescents in a Juvenile Justice Treatment Institution

Science.gov (United States)

Das, Jacqueline; de Ruiter, Corine; Doreleijers, Theo; Hillege, Sanne

2009-01-01

The present study examines the reliability and construct validity of the Dutch version of the Psychopathy Check List: Youth Version (PCL:YV) in a sample of male adolescents admitted to a secure juvenile justice treatment institution (N = 98). Hare's four-factor model is used to examine reliability and validity of the separate dimensions of…

Short-Run Contexts and Imperfect Testing for Continuous Sampling Plans

Directory of Open Access Journals (Sweden)

Mirella Rodriguez

2018-04-01

Full Text Available Continuous sampling plans are used to ensure a high level of quality for items produced in long-run contexts. The basic idea of these plans is to alternate between 100% inspection and a reduced rate of inspection frequency. Any inspected item that is found to be defective is replaced with a non-defective item. Because not all items are inspected, some defective items will escape to the customer. Analytical formulas have been developed that measure both the customer perceived quality and also the level of inspection effort. The analysis of continuous sampling plans does not apply to short-run contexts, where only a finite-size batch of items is to be produced. In this paper, a simulation algorithm is designed and implemented to analyze the customer perceived quality and the level of inspection effort for short-run contexts. A parameter representing the effectiveness of the test used during inspection is introduced to the analysis, and an analytical approximation is discussed. An application of the simulation algorithm that helped answer questions for the U.S. Navy is discussed.

A Psychometric Analysis of the Positive and Negative Affect Schedule for Children-Parent Version in a School Sample

Science.gov (United States)

Ebesutani, Chad; Okamura, Kelsie; Higa-McMillan, Charmaine; Chorpita, Bruce F.

2011-01-01

The current study was the 1st to examine the psychometric properties of the Positive and Negative Affect Schedule for Children-Parent Version (PANAS-C-P) using a large school-based sample of children and adolescents ages 8 to 18 (N = 606). Confirmatory factor analysis supported a 2-factor (correlated) model of positive affect (PA) and negative…

APGEN Version 5.0

Science.gov (United States)

Maldague, Pierre; Page, Dennis; Chase, Adam

2005-01-01

Activity Plan Generator (APGEN), now at version 5.0, is a computer program that assists in generating an integrated plan of activities for a spacecraft mission that does not oversubscribe spacecraft and ground resources. APGEN generates an interactive display, through which the user can easily create or modify the plan. The display summarizes the plan by means of a time line, whereon each activity is represented by a bar stretched between its beginning and ending times. Activities can be added, deleted, and modified via simple mouse and keyboard actions. The use of resources can be viewed on resource graphs. Resource and activity constraints can be checked. Types of activities, resources, and constraints are defined by simple text files, which the user can modify. In one of two modes of operation, APGEN acts as a planning expert assistant, displaying the plan and identifying problems in the plan. The user is in charge of creating and modifying the plan. In the other mode, APGEN automatically creates a plan that does not oversubscribe resources. The user can then manually modify the plan. APGEN is designed to interact with other software that generates sequences of timed commands for implementing details of planned activities.

Operable Unit 3-13, Group 3, Other Surface Soils (Phase II) Field Sampling Plan

Energy Technology Data Exchange (ETDEWEB)

G. L. Schwendiman

2006-07-27

This Field Sampling Plan describes the Operable Unit 3-13, Group 3, Other Surface Soils, Phase II remediation field sampling activities to be performed at the Idaho Nuclear Technology and Engineering Center located within the Idaho National Laboratory Site. Sampling activities described in this plan support characterization sampling of new sites, real-time soil spectroscopy during excavation, and confirmation sampling that verifies that the remedial action objectives and remediation goals presented in the Final Record of Decision for Idaho Nuclear Technology and Engineering Center, Operable Unit 3-13 have been met.

105-F and DR Phase 1 Sampling and Analysis Plan

International Nuclear Information System (INIS)

Curry, L.R.

1998-06-01

This SAP presents the rationale and strategy for characterization of specific rooms within the 105-F and 105-DR reactor buildings. Figures 1-1 and 1-2 identify the rooms that are the subject of this SAP. These rooms are to be decontaminated and demolished as an initial step (Phase 1 ) in the Interim Safe Storage process for these reactors. Section 1.0 presents the background and sites history for the reactor buildings and summarizes the data quality objective process, which provides the logical basis for this SAP. Preliminary surveys indicate that little radiochemical contamination is present. Section 2.0 presents the quality assurance project plan, which includes a project management structure, sampling methods and quality control, and oversight of the sampling process. Section 2.2.1 summarizes the sampling methods, reflecting the radiological and chemical sampling designs presented in Tables 1-17 and 1-18. Section 3.0 presents the Field Sampling Plan for Phase 1. The sampling design is broken into two stages. Stage 1 will verify the list of radioactive constituents of concern and generate the isotopic distribution. The objectives of Stage 2 are to estimate the radionuclide inventories of room debris, quantify chemical contamination, and survey room contents for potential salvage or recycle. Table 3-1 presents the sampling activities to be performed in Stage 1. Tables 1-17 and 1-18 identify samples to be collected in Stage 2. Stage 2 will consist primarily of survey data collection, with fixed laboratory samples to be collected in areas showing visible stains. Quality control sampling requirements are presented in Table 3-2

Confirmatory factor analysis and sample invariance of the Chinese version of Somatosensory Amplification Scale (ChSAS) among Chinese adolescents

OpenAIRE

Tam, B. K.; Wong, W. S.

2011-01-01

Objective: This paper aimed to evaluate the factor structure of the Chinese version of Somatosensory Amplification Scale (ChSAS) in a sample of Chinese adolescents across different grade levels using confirmatory factor analysis (CFA). Methods: A total of 1991 Chinese adolescents completed the ChSAS. CFA assessed the fit of the one-factor model to the entire sample. Factorial invariance of the ChSAS was also examined across grade levels using multigroup CFA. Results: Results of CFA confirmed ...

Tank 241-B-203 push mode core sampling and analysis plan. Revision 1

International Nuclear Information System (INIS)

Jo, J.

1995-01-01

This Sampling and Analysis Plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for two push-mode core samples from tank 241-B-203 (B-203)

Tank 241-B-204 push mode core sampling and analysis plan. Revision 1

International Nuclear Information System (INIS)

Sasaki, L.M.

1995-01-01

This Sampling and Analysis Plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for two push-mode core samples from tank 241-B-204 (B-204)

Test plan for K Basin Sludge Canister and Floor Sampling Device

International Nuclear Information System (INIS)

Meling, T.A.

1995-01-01

This document provides the test plan and procedure forms for conducting the functional and operational acceptance testing of the K Basin Sludge Canister and Floor Sampling Device(s). These samplers samples sludge off the floor of the 100K Basins and out of 100K fuel storage canisters

Efficient sampling algorithms for Monte Carlo based treatment planning

International Nuclear Information System (INIS)

DeMarco, J.J.; Solberg, T.D.; Chetty, I.; Smathers, J.B.

1998-01-01

Efficient sampling algorithms are necessary for producing a fast Monte Carlo based treatment planning code. This study evaluates several aspects of a photon-based tracking scheme and the effect of optimal sampling algorithms on the efficiency of the code. Four areas were tested: pseudo-random number generation, generalized sampling of a discrete distribution, sampling from the exponential distribution, and delta scattering as applied to photon transport through a heterogeneous simulation geometry. Generalized sampling of a discrete distribution using the cutpoint method can produce speedup gains of one order of magnitude versus conventional sequential sampling. Photon transport modifications based upon the delta scattering method were implemented and compared with a conventional boundary and collision checking algorithm. The delta scattering algorithm is faster by a factor of six versus the conventional algorithm for a boundary size of 5 mm within a heterogeneous geometry. A comparison of portable pseudo-random number algorithms and exponential sampling techniques is also discussed

Securing Retirement at a Young Age. Exploring the Intention to Buy Longevity Annuities through an Extended Version of the Theory of Planned Behavior

Directory of Open Access Journals (Sweden)

Costanza Nosi

2017-06-01

Full Text Available Since the early 90s, Italy has undergone radical changes in the regulations of the public pension system aimed at mending its main drawbacks and improving sustainability in the long run. The reforms were intended to recover the national economy through a significant reduction of benefits by increasing, particularly for younger people, individual responsibility for the accumulation of retirement wealth. Adopting an enhanced version of the Theory of Planned Behavior (TPB, which includes affective reactions, the present paper aims to understand the factors influencing the intention to enroll in a private pension plan through the purchase of longevity annuity coverage on the part of young adults. A purposive sample of 7480 Italian people aged 25–35 participated in the survey. Collected data were analyzed adopting an ordinal logistic regression (OLR model. The findings confirm the predictive power of the TPB in the financial field of longevity annuity buying, show that anticipated affective reactions increase the predictive power of the TPB model, and reveal that the influence of the investigated constructs varies alongside people’s willingness to purchase. The outcomes provide useful recommendations to the policy maker and private companies to favor the adoption of wide-spread desired behaviors among citizenships.

Data Management Plan

DEFF Research Database (Denmark)

Hansen, Ernst Jan de Place; Vogelsang, Stefan; Freudenberg, Peggy

2015-01-01

This document describes the Data Management Plan (DMP) (first version), relating to RIBuild WP8, deliverable D8.1. The DMP include description of data sets, standards and metadata, data sharing and archiving and preservation of data.......This document describes the Data Management Plan (DMP) (first version), relating to RIBuild WP8, deliverable D8.1. The DMP include description of data sets, standards and metadata, data sharing and archiving and preservation of data....

A short version of the revised 'experience of close relationships questionnaire': investigating non-clinical and clinical samples.

Science.gov (United States)

Wongpakaran, Tinakon; Wongpakaran, Nahathai

2012-01-01

This study seeks to investigate the psychometric properties of the short version of the revised 'Experience of Close Relationships' questionnaire, comparing non-clinical and clinical samples. In total 702 subjects participated in this study, of whom 531 were non-clinical participants and 171 were psychiatric patients. They completed the short version of the revised 'Experience of Close Relationships' questionnaire (ECR-R-18), the Perceived Stress Scale-10(PSS-10), the Rosenberg Self-Esteem Scale (RSES) and the UCLA Loneliness scale. A retest of the ECR-R-18 was then performed at four-week intervals. Then, confirmatory factor analyses were performed to test the validity of the new scale. The ECR-R-18 showed a fair to good internal consistency (α 0.77 to 0.87) for both samples, and the test-retest reliability was found to be satisfactory (ICC = 0.75). The anxiety sub-scale demonstrated concurrent validity with PSS-10 and RSES, while the avoidance sub-scale showed concurrent validity with the UCLA Loneliness Scale. Confirmatory factor analysis using method factors yielded two factors with an acceptable model fit for both groups. An invariance test revealed that the ECR-R-18 when used on the clinical group differed from when used with the non-clinical group. The ECR-R-18 questionnaire revealed an overall better level of fit than the original 36 item questionnaire, indicating its suitability for use with a broader group of samples, including clinical samples. The reliability of the ECR-R- 18 might be increased if a modified scoring system is used and if our suggestions with regard to future studies are followed up.

Tank 241-TX-113 rotary mode core sampling and analysis plan

International Nuclear Information System (INIS)

McCain, D.J.

1998-01-01

This sampling and analysis plan (SAP) identities characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for push mode core samples from tank 241-TX-113 (TX-113). The Tank Characterization Technical Sampling Basis document identities Retrieval, Pretreatment and Immobilization as an issue that applies to tank TX-113. As a result, a 150 gram composite of solids shall be made and archived for that program. This tank is not on a Watch List

Gas and liquid sampling for closed canisters in KW Basin - Work Plan

International Nuclear Information System (INIS)

Pitkoff, C.C.

1995-01-01

Work Plan for the design and fabrication of gas/liquid sampler for closed canister sampling in KW Basin. This document defines the tasks associated with the design, fabrication, assembly, and acceptance testing equipment necessary for gas and liquid sampling of the Mark I and Mark II canisters in the K-West basin. The sampling of the gas space and the remaining liquid inside the closed canisters will be used to help understand any changes to the fuel elements and the canisters. Specifically, this work plan will define the scope of work and required task structure, list the technical requirements, describe design configuration control and verification methodologies, detail quality assurance requirements, and present a baseline estimate and schedule

Tank 241-AY-101 Privatization Push Mode Core Sampling and Analysis Plan

International Nuclear Information System (INIS)

TEMPLETON, A.M.

2000-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AY-101. The purpose of this sampling event is to obtain information about the characteristics of the contents of 241-AY-101 required to satisfy ''Data Quality Objectives For RPP Privatization Phase I: Confirm Tank T Is An Appropriate Feed Source For High-Level Waste Feed Batch X(HLW DQO)' (Nguyen 1999a), ''Data Quality Objectives For TWRS Privatization Phase I: Confirm Tank T Is An Appropriate Feed Source For Low-Activity Waste Feed Butch X (LAW DQO) (Nguyen 1999b)'', ''Low Activity Waste and High-Level Waste Feed Data Quality Objectives (L and H DQO)'' (Patello et al. 1999), and ''Characterization Data Needs for Development, Design, and Operation of Retrieval Equipment Developed through the Data Quality Objective Process (Equipment DQO)'' (Bloom 1996). Special instructions regarding support to the LAW and HLW DQOs are provided by Baldwin (1999). Push mode core samples will be obtained from risers 15G and 150 to provide sufficient material for the chemical analyses and tests required to satisfy these data quality objectives. The 222-S Laboratory will extrude core samples; composite the liquids and solids; perform chemical analyses on composite and segment samples; archive half-segment samples; and provide sub-samples to the Process Chemistry Laboratory. The Process Chemistry Laboratory will prepare test plans and perform process tests to evaluate the behavior of the 241-AY-101 waste undergoing the retrieval and treatment scenarios defined in the applicable DQOs. Requirements for analyses of samples originating in the process tests will be documented in the corresponding test plans and are not within the scope of this SAP

UMTRA project water sampling and analysis plan, Falls City, Texas. Revision 1

International Nuclear Information System (INIS)

1995-09-01

Planned, routine ground water sampling activities at the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site near Falls City, Texas, are described in this water sampling and analysis plan (WSAP). The following plan identifies and justifies the sampling locations, analytical parameters, and sampling frequency for the routine monitoring stations at the site. The ground water data are used for site characterization and risk assessment. The regulatory basis for routine ground water monitoring at UMTRA Project sites is derived from the US Environmental Protection Agency (EPA) regulations in 40 CFR Part 192. Sampling procedures are guided by the UMTRA Project standard operating procedures (SOP) (JEG, n.d.), the Technical Approach Document (TAD) (DOE, 1989), and the most effective technical approach for the site. The Falls City site is in Karnes County, Texas, approximately 8 miles [13 kilometers southwest of the town of Falls City and 46 mi (74 km) southeast of San Antonio, Texas. Before surface remedial action, the tailings site consisted of two parcels. Parcel A consisted of the mill site, one mill building, five tailings piles, and one tailings pond south of Farm-to-Market (FM) Road 1344 and west of FM 791. A sixth tailings pile designated Parcel B was north of FM 791 and east of FM 1344

Herth hope index: psychometric testing of the Chinese version.

Science.gov (United States)

Chan, Keung Sum; Li, Ho Cheung William; Chan, Sally Wai-Chi; Lopez, Violeta

2012-09-01

This article is a report on psychometric testing of the Chinese version of the herth hope index. The availability of a valid and reliable instrument that accurately measures the level of hope in patients with heart failure is crucial before any hope-enhancing interventions can be appropriately planned and evaluated. There is no such instrument for Chinese people. A test-retest, within-subjects design was used. A purposive sample of 120 Hong Kong Chinese patients with heart failure between the ages of 60 and 80 years admitted to two medical wards was recruited during an 8-month period in 2009. Participants were asked to respond to the Chinese version of the herth hope index, Hamilton depression rating scale and Rosenberg's self-esteem scale. The internal consistency, content validity and construct validity and test-retest reliability of the Chinese version of the herth hope index were assessed. The newly translated scale demonstrated adequate internal consistency, good content validity and appropriate convergent and discriminant validity. Confirmatory factor analysis added further evidence of the construct validity of the scale. Results suggest that the newly translated scale can be used as a self-report assessment tool in assessing the level of hope in Hong Kong Chinese patients with heart failure. © 2011 Blackwell Publishing Ltd.

Tank 241-AY-101 Privatization Push Mode Core Sampling and Analysis Plan

International Nuclear Information System (INIS)

TEMPLETON, A.M.

2000-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AY-101. The purpose of this sampling event is to obtain information about the characteristics of the contents of 241-AY-101 required to satisfy Data Quality Objectives For RPP Privatization Phase I: Confirm Tank T Is An Appropriate Feed Source For High-Level Waste Feed Batch X(HLW DQO) (Nguyen 1999a), Data Quality Objectives For TWRS Privatization Phase I : Confirm Tank T Is An Appropriate Feed Source For Low-Activity Waste Feed Batch X (LAW DQO) (Nguyen 1999b), Low Activity Waste and High-Level Waste Feed Data Quality Objectives (L and H DQO) (Patello et al. 1999), and Characterization Data Needs for Development, Design, and Operation of Retrieval Equipment Developed through the Data Quality Objective Process (Equipment DQO) (Bloom 1996). Special instructions regarding support to the LAW and HLW DQOs are provided by Baldwin (1999). Push mode core samples will be obtained from risers 15G and 150 to provide sufficient material for the chemical analyses and tests required to satisfy these data quality objectives. The 222-S Laboratory will extrude core samples; composite the liquids and solids; perform chemical analyses on composite and segment samples; archive half-segment samples; and provide subsamples to the Process Chemistry Laboratory. The Process Chemistry Laboratory will prepare test plans and perform process tests to evaluate the behavior of the 241-AY-101 waste undergoing the retrieval and treatment scenarios defined in the applicable DQOs. Requirements for analyses of samples originating in the process tests will be documented in the corresponding test plans and are not within the scope of this SAP

Chain sampling plan (ChSP-1) for desired acceptable quality level (AQL) and limiting quality level (LQL)

Science.gov (United States)

Raju, C.; Vidya, R.

2017-11-01

Chain Sampling Plan is widely used whenever a small sample attributes plan is required to be used for situations involving destructive products coming out of continuous production process [1, 2]. This paper presents a procedure for the construction and selection of a ChSP-1 by attributes inspection based on membership functions [3]. A procedure using search technique is developed for obtaining the parameters of single sampling plan for a given set of AQL and LQL values. A sample of tables providing ChSP-1 plans for various combinations of AQL and LQL values are presented [4].

Differentially Constrained Motion Planning with State Lattice Motion Primitives

Science.gov (United States)

2012-02-01

underlying sampling lattice. 2.4 IMPLICIT SAMPLING Recent works have also discussed ”lazy” variants of the above planning methods that avoid colli ...settings, at the cost of performing colli - sion checking during the search. An even ”lazier” version is suggested, in which ”the initial graph CHAPTER...cycling at the border of fidelity regions due to obstacles, as suggested in Example 1.2.2. In order to avoid such difficulties, it is sufficient to

Planned development and evaluation protocol of two versions of a web-based computer-tailored nutrition education intervention aimed at adults, including cognitive and environmental feedback.

Science.gov (United States)

Springvloet, Linda; Lechner, Lilian; Oenema, Anke

2014-01-17

Despite decades of nutrition education, the prevalence of unhealthy dietary patterns is still high and inequalities in intake between high and low socioeconomic groups still exist. Therefore, it is important to innovate and improve existing nutrition education interventions. This paper describes the development, design and evaluation protocol of a web-based computer-tailored nutrition education intervention for adults targeting fruit, vegetable, high-energy snack and fat intake. This intervention innovates existing computer-tailored interventions by not only targeting motivational factors, but also volitional and self-regulation processes and environmental-level factors. The intervention development was guided by the Intervention Mapping protocol, ensuring a theory-informed and evidence-based intervention. Two versions of the intervention were developed: a basic version targeting knowledge, awareness, attitude, self-efficacy and volitional and self-regulation processes, and a plus version additionally addressing the home environment arrangement and the availability and price of healthy food products in supermarkets. Both versions consist of four modules: one for each dietary behavior, i.e. fruit, vegetables, high-energy snacks and fat. Based on the self-regulation phases, each module is divided into three sessions. In the first session, feedback on dietary behavior is provided to increase awareness, feedback on attitude and self-efficacy is provided and goals and action plans are stated. In the second session goal achievement is evaluated, reasons for failure are explored, coping plans are stated and goals can be adapted. In the third session, participants can again evaluate their behavioral change and tips for maintenance are provided. Both versions will be evaluated in a three-group randomized controlled trial with measurements at baseline, 1-month, 4-months and 9-months post-intervention, using online questionnaires. Both versions will be compared with a generic

Supplement to the UMTRA Project water sampling and analysis plan, Mexican Hat, Utah

International Nuclear Information System (INIS)

1995-09-01

This water sampling and analysis plan (WSAP) supplement supports the regulatory and technical basis for water sampling at the Mexican Hat, Utah, Uranium Mill Tailings Remedial Action (UMTRA) Project site, as defined in the 1994 WSAP document for Mexican Hat (DOE, 1994). Further, the supplement serves to confirm our present understanding of the site relative to the hydrogeology and contaminant distribution as well as our intention to continue to use the sampling strategy as presented in the 1994 WSAP document for Mexican Hat. Ground water and surface water monitoring activities are derived from the US Environmental Protection Agency regulations in 40 CFR Part 192 (1991) and 60 FR 2854 (1995). Sampling procedures are guided by the UMTRA Project standard operating procedures (JEG, n.d.), the Technical Approach Document (DOE, 1989), and the most effective technical approach for the site. Additional site-specific documents relevant to the Mexican Hat site are the Mexican Hat Long-Term Surveillance Plan (currently in progress), and the Mexican Hat Site Observational Work Plan (currently in progress)

Data Management Plan

DEFF Research Database (Denmark)

Hansen, Ernst Jan de Place; Sørensen, Nils Lykke

2016-01-01

This document describes the Data Management Plan (DMP) (second version), relating to RIBuild WP8, deliverable D8.1. It draws the first lines for how data can be made findable, accessible, interoperable and re-usable after the project period.......This document describes the Data Management Plan (DMP) (second version), relating to RIBuild WP8, deliverable D8.1. It draws the first lines for how data can be made findable, accessible, interoperable and re-usable after the project period....

Validation of the partner version of the multidimensional vaginal penetration disorder questionnaire: A tool for clinical assessment of lifelong vaginismus in a sample of Iranian population.

Science.gov (United States)

Molaeinezhad, Mitra; Khoei, Effat Merghati; Salehi, Mehrdad; Yousfy, Alireza; Roudsari, Robab Latifnejad

2014-01-01

The role of spousal response in woman's experience of pain during the vaginal penetration attempts believed to be an important factor; however, studies are rather limited in this area. The aim of this study was to develop and investigate the psychometric indexes of the partner version of a multidimensional vaginal penetration disorder questionnaire (PV-MVPDQ); hence, the clinical assessment of spousal psychosexual reactions to vaginismus by specialists will be easier. A mixed-methods sequential exploratory design was used, through that, the findings from a thematic qualitative research with 20 unconsummated couples, which followed by an extensive literature review used for development of PV-MVPDQ. A consecutive sample of 214 men who their wives' suffered from lifelong vaginismus (LLV) based on Diagnostic and Statistical Manual of Mental Disorders 4(th) version (DSM)-IVTR criteria during a cross-sectional design, completed the questionnaire and additional questions regarding their demographic and sexual history. Validation measures and reliability were conducted by exploratory factor analysis (EFA) and Cronbach's alpha coefficient through SPSS version 16 manufactured by SPSS Inc. (IBM corporation, Armonk, USA). After conducting EFA PV-MVPDQ emerged as having 40 items and 7 dimensions: Helplessness, sexual information, vicious cycle of penetration, hypervigilance and solicitous, catastrophic cognitions, sexual and marital adjustment and optimism. Subscales of PV-MVPDQ showed a significant reliability (0.71-0.85) and results of test-retest were satisfactory. The present study shows PV-MVPDQ is a multi-dimensional valid and reliable self-report questionnaire for assessment of cognitions, sexual and marital relations related to vaginal penetrations in spouses of women with LLV. It may assist specialists to base on which clinical judgment and appropriate planning for clinical management.

The reliability of the German version of the Richards Campbell Sleep Questionnaire.

Science.gov (United States)

Krotsetis, Susanne; Richards, Kathy C; Behncke, Anja; Köpke, Sascha

2017-07-01

The assessment of sleep quality in critically ill patients is a relevant factor of high-quality care. Despite the fact that sleep disturbances and insufficient sleep management contain an increased risk of severe morbidity for these patients, a translated and applicable instrument to evaluate sleep is not available for German-speaking intensive care settings. This study aimed to translate the Richards Campbell Sleep Questionnaire (RCSQ), a simple and validated instrument eligible for measuring sleep quality in critically ill patients, and subsequently to evaluate the internal consistency of the German version of the RCSQ. Furthermore, it also aimed to inquire into the perception of sleep in a sample of critically ill patients. The RCSQ was translated following established methodological standards. Data were collected cross-sectionally in a sample of 51 patients at 3 intensive care units at a university hospital in Germany. The German version of the RCSQ showed an overall internal consistency (Cronbach's alpha) of 0·88. The mean of the RSCQ in the sample was 47·00 (SD ± 27·57). Depth of sleep was rated the lowest and falling asleep again the highest of the RCSQ sleep items. The study demonstrated very good internal consistency of the German version of the RCSQ, allowing for its application in practice and research in German-speaking countries. Quality of sleep perception was generally low in this sample, emphasizing the need for enhanced care concepts regarding the sleep management of critically ill patients. Relevance to clinical practice Assessment of self-perception of sleep is crucial in order to plan an individually tailored care process. © 2017 British Association of Critical Care Nurses.

The Toggle Local Planner for sampling-based motion planning

KAUST Repository

Denny, Jory

2012-05-01

Sampling-based solutions to the motion planning problem, such as the probabilistic roadmap method (PRM), have become commonplace in robotics applications. These solutions are the norm as the dimensionality of the planning space grows, i.e., d > 5. An important primitive of these methods is the local planner, which is used for validation of simple paths between two configurations. The most common is the straight-line local planner which interpolates along the straight line between the two configurations. In this paper, we introduce a new local planner, Toggle Local Planner (Toggle LP), which extends local planning to a two-dimensional subspace of the overall planning space. If no path exists between the two configurations in the subspace, then Toggle LP is guaranteed to correctly return false. Intuitively, more connections could be found by Toggle LP than by the straight-line planner, resulting in better connected roadmaps. As shown in our results, this is the case, and additionally, the extra cost, in terms of time or storage, for Toggle LP is minimal. Additionally, our experimental analysis of the planner shows the benefit for a wide array of robots, with DOF as high as 70. © 2012 IEEE.

Gas liquid sampling for closed canisters in KW Basin - test plan

International Nuclear Information System (INIS)

Pitkoff, C.C.

1995-01-01

Test procedures for the gas/liquid sampler. Characterization of the Spent Nuclear Fuel, SNF, sealed in canisters at KW-Basin is needed to determine the state of storing SNF wet. Samples of the liquid and the gas in the closed canisters will be taken to gain characterization information. Sampling equipment has been designed to retrieve gas and liquid from the closed canisters in KW basin. This plan is written to outline the test requirements for this developmental sampling equipment

Incremental Validity Analyses of the Violence Risk Appraisal Guide and the Psychopathy Checklist: Screening Version in a Civil Psychiatric Sample

Science.gov (United States)

Edens, John F.; Skeem, Jennifer L.; Douglas, Kevin S.

2006-01-01

This study compares two instruments frequently used to assess risk for violence, the Violence Risk Appraisal Guide (VRAG) and the Psychopathy Checklist: Screening Version (PCL:SV), in a large sample of civil psychiatric patients. Despite a strong bivariate relationship with community violence, the VRAG could not improve on the predictive validity…

Failure-censored accelerated life test sampling plans for Weibull distribution under expected test time constraint

International Nuclear Information System (INIS)

Bai, D.S.; Chun, Y.R.; Kim, J.G.

1995-01-01

This paper considers the design of life-test sampling plans based on failure-censored accelerated life tests. The lifetime distribution of products is assumed to be Weibull with a scale parameter that is a log linear function of a (possibly transformed) stress. Two levels of stress higher than the use condition stress, high and low, are used. Sampling plans with equal expected test times at high and low test stresses which satisfy the producer's and consumer's risk requirements and minimize the asymptotic variance of the test statistic used to decide lot acceptability are obtained. The properties of the proposed life-test sampling plans are investigated

Transuranic waste characterization sampling and analysis plan

International Nuclear Information System (INIS)

1994-01-01

Los Alamos National Laboratory (the Laboratory) is located approximately 25 miles northwest of Santa Fe, New Mexico, situated on the Pajarito Plateau. Technical Area 54 (TA-54), one of the Laboratory's many technical areas, is a radioactive and hazardous waste management and disposal area located within the Laboratory's boundaries. The purpose of this transuranic waste characterization, sampling, and analysis plan (CSAP) is to provide a methodology for identifying, characterizing, and sampling approximately 25,000 containers of transuranic waste stored at Pads 1, 2, and 4, Dome 48, and the Fiberglass Reinforced Plywood Box Dome at TA-54, Area G, of the Laboratory. Transuranic waste currently stored at Area G was generated primarily from research and development activities, processing and recovery operations, and decontamination and decommissioning projects. This document was created to facilitate compliance with several regulatory requirements and program drivers that are relevant to waste management at the Laboratory, including concerns of the New Mexico Environment Department

UMTRA project water sampling and analysis plan, Salt Lake City, Utah

International Nuclear Information System (INIS)

1994-06-01

Surface remedial action was completed at the Salt Lake City, Utah, Uranium Mill Tailings Remedial Action (UMTRA) Project site in the fall of 1987. Results of water sampling for the years 1992 to 1994 indicate that site-related ground water contamination occurs in the shallow unconfined aquifer (the uppermost aquifer). With respect to background ground water quality, contaminated ground water in the shallow, unconfined aquifer has elevated levels of chloride, sodium, sulfate, total dissolved solids, and uranium. No contamination associated with the former tailings pile occurs in levels exceeding background in ground water in the deeper confined aquifer. This document provides the water sampling and analysis plan for ground water monitoring at the former uranium processing site in Salt Lake City, Utah (otherwise known as the ''Vitro'' site, named after the Vitro Chemical Company that operated the mill). All contaminated materials removed from the processing site were relocated and stabilized in a disposal cell near Clive, Utah, some 85 miles west of the Vitro site (known as the ''Clive'' disposal site). No ground water monitoring is being performed at the Clive disposal site, since concurrence of the remedial action plan by the US Nuclear Regulatory Commission and completion of the disposal cell occurred before the US Environmental Protection Agency issued draft ground water standards in 1987 (52 FR 36000) for cleanup, stabilization, and control of residual radioactive materials at the disposal site. In addition, the likelihood of post-closure impact on the ground water is minimal to nonexistent, due to the naturally poor quality of the ground water. Water sampling activities planned for calendar year 1994 consist of sampling ground water from nine monitor wells to assess the migration of contamination within the shallow unconfined aquifer and sampling ground water from two existing monitor wells to assess ground water quality in the confined aquifer

Statistical sampling plan for the TRU waste assay facility

International Nuclear Information System (INIS)

Beauchamp, J.J.; Wright, T.; Schultz, F.J.; Haff, K.; Monroe, R.J.

1983-08-01

Due to limited space, there is a need to dispose appropriately of the Oak Ridge National Laboratory transuranic waste which is presently stored below ground in 55-gal (208-l) drums within weather-resistant structures. Waste containing less than 100 nCi/g transuranics can be removed from the present storage and be buried, while waste containing greater than 100 nCi/g transuranics must continue to be retrievably stored. To make the necessary measurements needed to determine the drums that can be buried, a transuranic Neutron Interrogation Assay System (NIAS) has been developed at Los Alamos National Laboratory and can make the needed measurements much faster than previous techniques which involved γ-ray spectroscopy. The previous techniques are reliable but time consuming. Therefore, a validation study has been planned to determine the ability of the NIAS to make adequate measurements. The validation of the NIAS will be based on a paired comparison of a sample of measurements made by the previous techniques and the NIAS. The purpose of this report is to describe the proposed sampling plan and the statistical analyses needed to validate the NIAS. 5 references, 4 figures, 5 tables

Tank 241-AZ-102 Privatization Push Mode Core Sampling and Analysis Plan

International Nuclear Information System (INIS)

RASMUSSEN, J.H.

1999-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AZ-102. The purpose of this sampling event is to obtain information about the characteristics of the contents of 241-AZ-102 required to satisfy the Data Quality Objectives For TWRS Privatization Phase I : Confirm Tank TIS An Appropriate Feed Source For High-Level Waste Feed Batch X(HLW DQO) (Nguyen 1999a), Data Quality Objectives For TWRS Privatization Phase 1: Confirm Tank TIS An Appropriate Feed Source For Low-Activity Waste Feed Batch X (LAW DQO) (Nguyen 1999b), Low Activity Waste and High Level Waste Feed Data Quality Objectives (L and H DQO) (Patello et al. 1999) and Characterization Data Needs for Development, Design, and Operation of Retrieval Equipment Developed through the Data Quality Objective Process (Equipment DQO) (Bloom 1996). The Tank Characterization Technical Sampling Basis document (Brown et al. 1998) indicates that these issues, except the Equipment DQO apply to tank 241-AZ-102 for this sampling event. The Equipment DQO is applied for shear strength measurements of the solids segments only. Poppiti (1999) requires additional americium-241 analyses of the sludge segments. Brown et al. (1998) also identify safety screening, regulatory issues and provision of samples to the Privatization Contractor(s) as applicable issues for this tank. However, these issues will not be addressed via this sampling event. Reynolds et al. (1999) concluded that information from previous sampling events was sufficient to satisfy the safety screening requirements for tank 241-AZ-102. Push mode core samples will be obtained from risers 15C and 24A to provide sufficient material for the chemical analyses and tests required to satisfy these data quality objectives. The 222-S Laboratory will extrude core samples, composite the liquids and solids, perform chemical analyses

The Pemberton Happiness Index: Validation of the Universal Portuguese version in a large Brazilian sample.

Science.gov (United States)

Paiva, Bianca Sakamoto Ribeiro; de Camargos, Mayara Goulart; Demarzo, Marcelo Marcos Piva; Hervás, Gonzalo; Vázquez, Carmelo; Paiva, Carlos Eduardo

2016-09-01

The Pemberton Happiness Index (PHI) is a recently developed integrative measure of well-being that includes components of hedonic, eudaimonic, social, and experienced well-being. The PHI has been validated in several languages, but not in Portuguese. Our aim was to cross-culturally adapt the Universal Portuguese version of the PHI and to assess its psychometric properties in a sample of the Brazilian population using online surveys.An expert committee evaluated 2 versions of the PHI previously translated into Portuguese by the original authors using a standardized form for assessment of semantic/idiomatic, cultural, and conceptual equivalence. A pretesting was conducted employing cognitive debriefing methods. In sequence, the expert committee evaluated all the documents and reached a final Universal Portuguese PHI version. For the evaluation of the psychometric properties, the data were collected using online surveys in a cross-sectional study. The study population included healthcare professionals and users of the social network site Facebook from several Brazilian geographic areas. In addition to the PHI, participants completed the Satisfaction with Life Scale (SWLS), Diener and Emmons' Positive and Negative Experience Scale (PNES), Psychological Well-being Scale (PWS), and the Subjective Happiness Scale (SHS). Internal consistency, convergent validity, known-group validity, and test-retest reliability were evaluated. Satisfaction with the previous day was correlated with the 10 items assessing experienced well-being using the Cramer V test. Additionally, a cut-off value of PHI to identify a "happy individual" was defined using receiver-operating characteristic (ROC) curve methodology.Data from 1035 Brazilian participants were analyzed (health professionals = 180; Facebook users = 855). Regarding reliability results, the internal consistency (Cronbach alpha = 0.890 and 0.914) and test-retest (intraclass correlation coefficient = 0.814) were both considered

Field Investigation Plan for 1301-N and 1325-N Facilities Sampling to Support Remedial Design

International Nuclear Information System (INIS)

Weiss, S. G.

1998-01-01

This field investigation plan (FIP) provides for the sampling and analysis activities supporting the remedial design planning for the planned removal action for the 1301-N and 1325-N Liquid Waste Disposal Facilities (LWDFs), which are treatment, storage,and disposal (TSD) units (cribs/trenches). The planned removal action involves excavation, transportation, and disposal of contaminated material at the Environmental Restoration Disposal Facility (ERDF).An engineering study (BHI 1997) was performed to develop and evaluate various options that are predominantly influenced by the volume of high- and low-activity contaminated soil requiring removal. The study recommended that additional sampling be performed to supplement historical data for use in the remedial design

Compatibility Grab Sampling and Analysis Plan for FY 2000

International Nuclear Information System (INIS)

SASAKI, L.M.

1999-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for grab samples obtained to address waste compatibility. It is written in accordance with requirements identified in Data Quality Objectives for Tank Farms Waste Compatibility Program (Mulkey et al. 1999) and Tank Farm Waste Transfer Compatibility Program (Fowler 1999). In addition to analyses to support Compatibility, the Waste Feed Delivery program has requested that tank samples obtained for Compatibility also be analyzed to confirm the high-level waste and/or low-activity waste envelope(s) for the tank waste (Baldwin 1999). The analytical requirements to confirm waste envelopes are identified in Data Quality Objectives for TWRS Privatization Phase I: Confirm Tank T is an Appropriate Feed Source for Low-Activity Waste Feed Batch X (Nguyen 1999a) and Data Quality Objectives for RPP Privatization Phase I: Confirm Tank T is an Appropriate Feed Source for High-Level Waste Feed Batch X (Nguyen 1999b)

Planning Related to the Curation and Processing of Returned Martian Samples

Science.gov (United States)

McCubbin, F. M.; Harrington, A. D.

2018-04-01

Many of the planning activities in the NASA Astromaterials Acquisition and Curation Office at JSC are centered around Mars Sample Return. The importance of contamination knowledge and the benefits of a mobile/modular receiving facility are discussed.

Validation of the Italian version of the Yale Food Addiction Scale 2.0 (I-YFAS 2.0) in a sample of undergraduate students.

Science.gov (United States)

Aloi, Matteo; Rania, Marianna; Rodríguez Muñoz, Rita Cristina; Jiménez Murcia, Susana; Fernández-Aranda, Fernando; De Fazio, Pasquale; Segura-Garcia, Cristina

2017-09-01

Food addiction (FA) refers to a condition characterized by addiction in relation to some high-fat and high-sugar carbohydrate that leads to clinically significant impairment or distress on several areas of functioning. The Yale Food Addiction Scale 2.0 (YFAS 2.0) has been recently updated to measure FA according to the DSM-5 criteria for substance-related and addictive disorders. This study aimed at validating the Italian version of YFAS 2.0. A sample of 574 Italian university students was involved in this research. Confirmatory Factor Analysis (CFA) and Kuder-Richardson's alpha for dichotomous data were run to evaluate scale structure and reliability. Correlations between YFAS 2.0 and eating psychopathology, binge eating, sleep, and mood symptoms were evaluated. Analogously to the original version, a single factor structure emerged at the CFA. The alpha coefficient was 0.87. Moreover, sound, from moderate to high, correlations were found with other measures. The Italian version of the YFAS 2.0 has demonstrated in a sample of university students to be a useful tool to investigate food addictions. Level of evidence Level V, descriptive study.

Validity and reliability of the European portuguese version of neuropsychiatric inventory in an institutionalized sample.

Science.gov (United States)

Ferreira, Ana Rita; Martins, Sonia; Ribeiro, Orquidea; Fernandes, Lia

2015-01-01

Neuropsychiatric symptoms are very common in dementia and have been associated with patient and caregiver distress, increased risk of institutionalization and higher costs of care. In this context, the neuropsychiatric inventory (NPI) is the most widely used comprehensive tool designed to measure neuropsychiatric Symptoms in geriatric patients with dementia. The aim of this study was to present the validity and reliability of the European Portuguese version of NPI. A cross-sectional study was carried out with a convenience sample of institutionalized patients (≥ 50 years old) in three nursing homes in Portugal. All patients were also assessed with mini-mental state examination (MMSE) (cognition), geriatric depression scale (GDS) (depression) and adults and older adults functional assessment inventory (IAFAI) (functionality). NPI was administered to a formal caregiver, usually from the clinical staff. Inter-rater and test-retest reliability were assessed in a subsample of 25 randomly selected subjects. The sample included 166 elderly, with a mean age of 80.9 (standard deviation: 10.2) years. Three out of the NPI behavioral items had negative correlations with MMSE: delusions (rs = -0.177, P = 0.024), disinhibition (rs = -0.174, P = 0.026) and aberrant motor activity (rs = -0.182, P = 0.020). The NPI subsection of depression/dysphoria correlated positively with GDS total score (rs = 0.166, P = 0.038). NPI showed good internal consistency (overall α = 0.766; frequency α = 0.737; severity α = 0.734). The inter-rater reliability was excellent (intraclass correlation coefficient (ICC): 1.00, 95% confidence interval (CI) 1.00 - 1.00), as well as test-retest reliability (ICC: 0.91, 95% CI 0.80 - 0.96). The results found for convergent validity, inter-rater and test-retest reliability, showed that this version appears to be a valid and reliable instrument for evaluation of neuropsychiatric symptoms in institutionalized elderly.

Supplement to the UMTRA Project water sampling and analysis plan, Maybell, Colorado

International Nuclear Information System (INIS)

1995-09-01

This water sampling and analysis plan (WSAP) supplement supports the regulatory and technical basis for water sampling at the Maybell, Colorado, Uranium Mill Tailings Remedial Action (UMTRA) Project site, as defined in the 1994 WSAP document for Maybell (DOE, 1994a). Further, this supplement serves to confirm our present understanding of the site relative to the hydrogeology and contaminant distribution as well as our intention to continue to use the sampling strategy as presented in the 1994 WSAP document for Maybell. Ground water and surface water monitoring activities are derived from the US Environmental Protection Agency regulations in 40 CFR Part 192 (1994) and 60 CFR 2854 (1 995). Sampling procedures are guided by the UMTRA Project standard operating procedures (JEG, n.d.), the Technical Approach Document (DOE, 1989), and the most effective technical approach for the site. Additional site-specific documents relevant to the Maybell site are the Maybell Baseline Risk Assessment (currently in progress), the Maybell Remedial Action Plan (RAP) (DOE, 1994b), and the Maybell Environmental Assessment (DOE, 1995)

NACS Store Planning Manual.

Science.gov (United States)

College Store Journal, 1979

1979-01-01

Topics discussed by the NACS Store Planning/Renovation Committees in this updated version of the college store renovation manual include: short- and long-range planning, financial considerations, professional planning assistance, the store's image and business character, location considerations, building requirements, space requirements, fixtures,…

The comparison of CAP88-PC version 2.0 versus CAP88-PC version 1.0

International Nuclear Information System (INIS)

Yakubovich, B.A.; Klee, K.O.; Palmer, C.R.; Spotts, P.B.

1997-12-01

40 CFR Part 61 (Subpart H of the NESHAP) requires DOE facilities to use approved sampling procedures, computer models, or other approved procedures when calculating Effective Dose Equivalent (EDE) values to members of the public. Currently version 1.0 of the approved computer model CAP88-PC is used to calculate EDE values. The DOE has upgraded the CAP88-PC software to version 2.0. This version provides simplified data entry, better printing characteristics, the use of a mouse, and other features. The DOE has developed and released version 2.0 for testing and comment. This new software is a WINDOWS based application that offers a new graphical user interface with new utilities for preparing and managing population and weather data, and several new decay chains. The program also allows the user to view results before printing. This document describes a test that confirmed CAP88-PC version 2.0 generates results comparable to the original version of the CAP88-PC program

Assessment of Mindfulness with the French Version of the Kentucky Inventory of Mindfulness Skills in Community and Borderline Personality Disorder Samples

Science.gov (United States)

Nicastro, Rosetta; Jermann, Francoise; Bondolfi, Guido; McQuillan, Annabel

2010-01-01

This article explores mindfulness skills in community and borderline personality disorder (BPD) samples. Study 1 includes 173 community volunteers and explores the psychometric properties of the French version of the Kentucky Inventory of Mindfulness Skills (KIMS). Study 2 explores the KIMS factor structure in 130 BPD patients and compares KIMS…

Engineering Task Plan to Expand the Environmental Operational Envelope of Core Sampling

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

This Engineering Task Plan authorizes the development of an Alternative Generation and Analysis (AGA). The AGA will determine how to expand the environmental operating envelope during core sampling operations

The Psychometric Properties of Turkish Version of Depression Anxiety Stress Scale-21 (DASS-21) in Community and Clinical Samples

OpenAIRE

Hakan SARICAM

2018-01-01

This paper presented the Turkish version of the Depression Anxiety Stress Scale-21 (DASS-21) in community and clinical samples, examined its psychometric properties. Construct validity and concurrent validity were conducted in validity studies. Depression Anxiety Stress Scale-42 (DASS-42) was used for concurrent validity. In reliability analysis, the instruments internal consistency and re-test reliability were studied. Results of explanatory factor analyses demonstrated that 21 items yielded...

Validation of the Portuguese version of the Brief Multidimensional Measure of Religiousness/Spirituality (BMMRS-P) in clinical and non-clinical samples.

Science.gov (United States)

Curcio, Cristiane Schumann Silva; Lucchetti, Giancarlo; Moreira-Almeida, Alexander

2015-04-01

Despite Brazil's high levels of religious involvement, there is a scarcity of validated religiousness/spirituality (R/S) measures in Portuguese, particularly multidimensional ones. This study presents the validation of the Portuguese version of the "Brief Multidimensional Measure in Religiousness and Spirituality" (BMMRS) within the Brazilian context. Inpatients (262) and caregivers (389) at two hospitals of Brazil answered the BMMRS, the DUREL-p, and a sociodemographic questionnaire. The internal and convergent validity and test-retest reliability for major dimensions were good. Discriminant validity was high (except for the Forgiveness dimension). The Portuguese version of the BMMRS is a reliable and valid instrument to assess multiple R/S dimensions in clinical and non-clinical samples.

Chemical Hygiene Plan for Onsite Measurement and Sample Shipping Facility Activities

International Nuclear Information System (INIS)

Price, W.H.

1998-01-01

This chemical hygiene plan presents the requirements established to ensure the protection of employee health while performing work in mobile laboratories, the sample shipping facility, and at the onsite radiological counting facility. This document presents the measures to be taken to promote safe work practices and to minimize worker exposure to hazardous chemicals. Specific hazardous chemicals present in the mobile laboratories, the sample shipping facility, and in the radiological counting facility are presented in Appendices A through G

Development and tests of short versions of the Youth Psychopathic traits Inventory and the Youth Psychopathic traits Inventory-Child Version

NARCIS (Netherlands)

van Baardewijk, Y.; Andershed, H.; Stegge, G.T.M.; Nilsson, K.W.; Scholte, E.; Vermeiren, R.R.J.M.

2010-01-01

The adolescent Youth Psychopathic Traits Inventory (YPI) and its child version (YPI-CV) are sound but lengthy instruments for measuring psychopathic traits in youths. The current study develops psychometrically strong short versions of these instruments. Samples used for item reduction were

UMTRA project water sampling and analysis plan -- Shiprock, New Mexico

International Nuclear Information System (INIS)

1994-02-01

Water sampling and analysis plan (WSAP) is required for each U.S. Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site to provide a basis for ground water and surface water sampling at disposal and former processing sites. This WSAP identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the monitoring stations at the Navaho Reservation in Shiprock, New Mexico, UMTRA Project site. The purposes of the water sampling at Shiprock for fiscal year (FY) 1994 are to (1) collect water quality data at new monitoring locations in order to build a defensible statistical data base, (2) monitor plume movement on the terrace and floodplain, and (3) monitor the impact of alluvial ground water discharge into the San Juan River. The third activity is important because the community of Shiprock withdraws water from the San Juan River directly across from the contaminated alluvial floodplain below the abandoned uranium mill tailings processing site

Supplement to the UMTRA Project water sampling and analysis plan, Monument Valley, Arizona

International Nuclear Information System (INIS)

1995-09-01

This water sampling and analysis plan (WSAP) supplement supports the regulatory and technical basis for water sampling at the Riverton, Wyoming, Uranium Mill Tailings Remedial Action (UMTRA) Project site, as defined in the 1994 WSAP document for Riverton (DOE, 1994). Further, the supplement serves to confirm the Project's present understanding of the site relative to the hydrogeology and contaminant distribution as well as the intent to continue to use the sampling strategy as presented in the 1994 WSAP document for Riverton. Ground water and surface water monitoring activities are derived from the US Environmental Protection Agency regulations in 40 CFR Part 192 and 60 FR 2854. Sampling procedures are guided by the UMTRA Project standard operating procedures (JEG, n.d.), the Technical Approach Document (DOE, 1989), and the most effective technical approach for the site. Additional site-specific documents relevant to the Riverton site are the Riverton Baseline Risk Assessment (BLRA) (DOE, 1995a) and the Riverton Site Observational Work Plan (SOWP) (DOE, 1995b)

C-018H Pre-Operational Baseline Sampling Plan

International Nuclear Information System (INIS)

Guzek, S.J.

1993-01-01

The objective of this task is to field characterize and sample the soil at selected locations along the proposed effluent line routes for Project C-018H. The overall purpose of this effort is to meet the proposed plan to discontinue the disposal of contaminated liquids into the Hanford soil column as described by DOE (1987). Detailed information describing proposed transport pipeline route and associated Kaiser Engineers Hanford Company (KEH) preliminary drawings (H288746...755) all inclusive, have been prepared by KEH (1992). The information developed from field monitoring and sampling will be utilized to characterize surface and subsurface soil along the proposed C-018H effluent pipeline and it's associated facilities. Potentially existing contaminant levels may be encountered therefore, soil characterization will provide a construction preoperational baseline reference, develop personnel safety requirements, and determine the need for any changes in the proposed routes prior to construction of the pipeline

Food safety assurance systems: Microbiological testing, sampling plans, and microbiological criteria

NARCIS (Netherlands)

Zwietering, M.H.; Ross, T.; Gorris, L.G.M.

2014-01-01

Microbiological criteria give information about the quality or safety of foods. A key component of a microbiological criterion is the sampling plan. Considering: (1) the generally low level of pathogens that are deemed tolerable in foods, (2) large batch sizes, and (3) potentially substantial

10 CFR Appendix A to Subpart U of... - Sampling Plan for Enforcement Testing of Electric Motors

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Sampling Plan for Enforcement Testing of Electric Motors A Appendix A to Subpart U of Part 431 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY... to Subpart U of Part 431—Sampling Plan for Enforcement Testing of Electric Motors Step 1. The first...

Double-Shell Tank (DST) Ventilation System Vapor Sampling and Analysis Plan

International Nuclear Information System (INIS)

SASAKI, L.M.

2000-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for vapor samples from the primary ventilation systems of the AN, AP, AW, and AY/AZ tank farms. Sampling will be performed in accordance with Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis (Air DQO) (Mulkey 1999). The sampling will verify if current air emission estimates used in the permit application are correct and provide information for future air permit applications. Vapor samples will be obtained from tank farm ventilation systems, downstream from the tanks and upstream of any filtration. Samples taken in support of the DQO will consist of SUMMA(trademark) canisters, triple sorbent traps (TSTs), sorbent tube trains (STTs), polyurethane foam (PUF) samples. Particulate filter samples and tritium traps will be taken for radiation screening to allow the release of the samples for analysis. The following sections provide the general methodology and procedures to be used in the preparation, retrieval, transport, analysis, and reporting of results from the vapor samples

Assessing Mindfulness on a Sample of Catalan-Speaking Spanish Adolescents: Validation of the Catalan Version of the Child and Adolescent Mindfulness Measure.

Science.gov (United States)

Viñas, Ferran; Malo, Sara; González, Mònica; Navarro, Dolors; Casas, Ferran

2015-06-22

Interest in mindfulness has increased over the last decade, resulting in several mindfulness-based interventions being developed and their efficacy empirically demonstrated. The practice of mindfulness has been associated with low levels of anxiety or depression and improved quality of life or personal well-being. The aim of this study is to translate the Child and Adolescent Mindfulness Measure (CAMM) and adapt it to Catalan so as to analyze its internal consistency and construct and convergent validity. The CAMM was administered to a sample of secondary school students ranging in age from 11 to 16 years old. The Catalan version of the CAMM shows a good fit with the unidimensional model and internal consistency similar to the original version (α = .80). Furthermore, CAMM scores correlated positively with subjective well-being, temperamental dimensions of effortful control and self-esteem. The Catalan Version of CAMM is a valid and reliable measure of mindfulness skills.

Maternal outcomes of term breech presentation delivery: impact of successful external cephalic version in a nationwide sample of delivery admissions in the United States.

Science.gov (United States)

Weiniger, Carolyn F; Lyell, Deirdre J; Tsen, Lawrence C; Butwick, Alexander J; Shachar, BatZion; Callaghan, William M; Creanga, Andreea A; Bateman, Brian T

2016-07-08

We aimed to define the frequency and predictors of successful external cephalic version in a nationally-representative cohort of women with breech presentations and to compare maternal outcomes associated with successful external cephalic version versus persistent breech presentation. Using the Nationwide Inpatient Sample, a United States healthcare utilization database, we identified delivery admissions between 1998 and 2011 for women who had successful external cephalic version or persistent breech presentation (including unsuccessful or no external cephalic version attempt) at term. Multivariable logistic regression identified patient and hospital-level factors associated with successful external cephalic version. Maternal outcomes were compared between women who had successful external cephalic version versus persistent breech. Our study cohort comprised 1,079,576 delivery admissions with breech presentation; 56,409 (5.2 %) women underwent successful external cephalic version and 1,023,167 (94.8 %) women had persistent breech presentation at the time of delivery. The rate of cesarean delivery was lower among women who had successful external cephalic version compared to those with persistent breech (20.2 % vs. 94.9 %; p external cephalic version were also less likely to experience several measures of significant maternal morbidity including endometritis (adjusted Odds Ratio (aOR) = 0.36, 95 % Confidence Interval (CI) 0.24-0.52), sepsis (aOR = 0.35, 95 % CI 0.24-0.51) and length of stay > 7 days (aOR = 0.53, 95 % CI 0.40-0.70), but had a higher risk of chorioamnionitis (aOR = 1.83, 95 % CI 1.54-2.17). Overall a low proportion of women with breech presentation undergo successful external cephalic version, and it is associated with significant reduction in the frequency of cesarean delivery and a number of measures of maternal morbidity. Increased external cephalic version use may be an important approach to mitigate the high rate of

Optimal sampling plan for clean development mechanism energy efficiency lighting projects

International Nuclear Information System (INIS)

Ye, Xianming; Xia, Xiaohua; Zhang, Jiangfeng

2013-01-01

Highlights: • A metering cost minimisation model is built to assist the sampling plan for CDM projects. • The model minimises the total metering cost by the determination of optimal sample size. • The required 90/10 criterion sampling accuracy is maintained. • The proposed metering cost minimisation model is applicable to other CDM projects as well. - Abstract: Clean development mechanism (CDM) project developers are always interested in achieving required measurement accuracies with the least metering cost. In this paper, a metering cost minimisation model is proposed for the sampling plan of a specific CDM energy efficiency lighting project. The problem arises from the particular CDM sampling requirement of 90% confidence and 10% precision for the small-scale CDM energy efficiency projects, which is known as the 90/10 criterion. The 90/10 criterion can be met through solving the metering cost minimisation problem. All the lights in the project are classified into different groups according to uncertainties of the lighting energy consumption, which are characterised by their statistical coefficient of variance (CV). Samples from each group are randomly selected to install power meters. These meters include less expensive ones with less functionality and more expensive ones with greater functionality. The metering cost minimisation model will minimise the total metering cost through the determination of the optimal sample size at each group. The 90/10 criterion is formulated as constraints to the metering cost objective. The optimal solution to the minimisation problem will therefore minimise the metering cost whilst meeting the 90/10 criterion, and this is verified by a case study. Relationships between the optimal metering cost and the population sizes of the groups, CV values and the meter equipment cost are further explored in three simulations. The metering cost minimisation model proposed for lighting systems is applicable to other CDM projects as

Health plan auditing: 100-percent-of-claims vs. random-sample audits.

Science.gov (United States)

Sillup, George P; Klimberg, Ronald K

2011-01-01

The objective of this study was to examine the relative efficacy of two different methodologies for auditing self-funded medical claim expenses: 100-percent-of-claims auditing versus random-sampling auditing. Multiple data sets of claim errors or 'exceptions' from two Fortune-100 corporations were analysed and compared to 100 simulated audits of 300- and 400-claim random samples. Random-sample simulations failed to identify a significant number and amount of the errors that ranged from $200,000 to $750,000. These results suggest that health plan expenses of corporations could be significantly reduced if they audited 100% of claims and embraced a zero-defect approach.

Compatibility grab sampling and analysis plan for fiscal year 1999

International Nuclear Information System (INIS)

SASAKI, L.M.

1999-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for grab samples obtained to address waste compatibility. Analytical requirements are taken from two revisions of the Compatibility data quality objectives (DQOs). Revision 1 of the DQO (Fowler 1995) listed analyses to be performed to meet both safety and operational data needs for the Compatibility program. Revision 2A of the DQO (Mulkey and Miller 1998) addresses only the safety-related requirements; the operational requirements of Fowler (1995) have not been superseded by Mulkey and Miller (1998). Therefore, safety-related data needs are taken from Mulkey and Miller (1998) and operational-related data needs are taken from Fowler (1995). Ammonia and total alpha analyses are also performed in accordance with Fowler (1998a, 1998b)

Obsessive-compulsive symptoms in a normative Chinese sample of youth: prevalence, symptom dimensions, and factor structure of the Leyton Obsessional Inventory--Child Version.

Science.gov (United States)

Sun, Jing; Boschen, Mark J; Farrell, Lara J; Buys, Nicholas; Li, Zhan-Jiang

2014-08-01

Chinese adolescents face life stresses from multiple sources, with higher levels of stress predictive of adolescent mental health outcomes, including in the area of obsessive-compulsive disorders (OCD). Valid assessment of OCD among this age group is therefore a critical need in China. This study aims to standardise the Chinese version of the Leyton short version scale for adolescents of secondary schools in order to assess this condition. Stratified randomly selected adolescents were selected from four high schools located in Beijing, China. The Chinese version of the Leyton scale was administered to 3221 secondary school students aged between 12 and 18 years. A high response rate was achieved, with 3185 adolescents responding to the survey (98.5 percent). Exploratory factor analysis (EFA) extracted four factors from the scale: compulsive thoughts, concerns of cleanliness, lucky number, repetitiveness and repeated checking. The four-factor structures were confirmed using Confirmatory Factor Analysis (CFA). Overall the four-factor structure had a good model fit and high levels of reliability for each individual dimension and reasonable content validity. Invariance analyses in unconstrained, factor loading, and error variance models demonstrated that the Leyton scale is invariant in relation to the presence or absence OCD, age and gender. Discriminant validity analysis demonstrated that the four-factor structure scale also had excellent ability to differentiate between OCD and non-OCD students, male and female students, and age groups. The dataset was a non-clinical sample of high school students, rather than a sample of individuals with OCD. Future research may examine symptom structure in clinical populations to assess whether this structure fits into both clinical and community population. The structure derived from the Leyton short version scale in a non-clinical secondary school sample of adolescents, suggests that a four-factor solution can be utilised as a

Psychometric Properties of the Persian Version of the Difficulties in Emotion Regulation Scale) DERS-6 & DERS-5- Revised (in an Iranian Clinical Sample.

Science.gov (United States)

Mazaheri, Mina

2015-04-01

The purpose of this study was to determine the construct validity and reliability of the two forms of the Persian version of the Difficulties in Emotion Regulation Scale (DERS-6 & DERS-5-revised) in a clinical sample. The clinical sample consisted of 181 patients diagnosed with Functional GI Disorders (FGID) who referred to the digestive psychosomatic clinic in Isfahan in 2012. They were selected by census method (In a given period of time). The Persian version of the DERS, the short form of the DASS, and the TAS-20 were used to collect data. The results of the factor structure or construct validity using principal components analysis with varimax rotation recognized 7 factors for the DERS-6 (Goals, Awarness, Impalse, Non Acceptance, Strategy, Clarity, Recognition), and 6 factors for the DERS-5- revised (Non Acceptance, Goals, Impalse, Strategy, Clarity, Recognition) in the clinical sample. They showed the common variance of 59.51% and 59.15%, respectively. Also, the results showed that the concurrent validity of both forms of the DERS and most of their factors, and their reliability in terms of Cronbach-Alpha were favorable. Considering the factor structure and favorable psychometric properties of the two scales of DERS-6 & DERS-5-revised, the scales can be used in clinical samples.

Factorial structure of the German version of the dimensional assessment of personality pathology-basic questionnaire in clinical and nonclinical samples.

Science.gov (United States)

Pukrop, R; Gentil, I; Steinbring, I; Steinmeyer, E

2001-10-01

The Dimensional Assessment of Personality Pathology-Basic Questionnaire (DAPP-BQ) assesses 18 traits to provide a systematic representation of the overall domain of personality disorders. We tested the cross-cultural stability of the prediction that four higher-order factors (Emotional Dysregulation, Dissocial Behavior, Inhibitedness, and Compulsivity) underlie the 18 basic traits. A total of 81 patients who were primarily treated for an Axis II personality disorder and N = 166 healthy control patients completed the German version of the DAPP-BQ. Results clearly confirmed cross-cultural stability of the postulated four-factor structure in both samples, accounting for 74.7% (clinical sample), and 65.7% (nonclinical sample) of the total variance. All four higher-order factors showed specific correlational relationships with dimensional assessments of DSM-IV personality disorders.

Resource Planning Model: An Integrated Resource Planning and Dispatch Tool for Regional Electric Systems

Energy Technology Data Exchange (ETDEWEB)

Mai, T.; Drury, E.; Eurek, K.; Bodington, N.; Lopez, A.; Perry, A.

2013-01-01

This report introduces a new capacity expansion model, the Resource Planning Model (RPM), with high spatial and temporal resolution that can be used for mid- and long-term scenario planning of regional power systems. Although RPM can be adapted to any geographic region, the report describes an initial version of the model adapted for the power system in Colorado. It presents examples of scenario results from the first version of the model, including an example of a 30%-by-2020 renewable electricity penetration scenario.

Development and Demonstration of a Method to Evaluate Bio-Sampling Strategies Using Building Simulation and Sample Planning Software.

Science.gov (United States)

Dols, W Stuart; Persily, Andrew K; Morrow, Jayne B; Matzke, Brett D; Sego, Landon H; Nuffer, Lisa L; Pulsipher, Brent A

2010-01-01

In an effort to validate and demonstrate response and recovery sampling approaches and technologies, the U.S. Department of Homeland Security (DHS), along with several other agencies, have simulated a biothreat agent release within a facility at Idaho National Laboratory (INL) on two separate occasions in the fall of 2007 and the fall of 2008. Because these events constitute only two realizations of many possible scenarios, increased understanding of sampling strategies can be obtained by virtually examining a wide variety of release and dispersion scenarios using computer simulations. This research effort demonstrates the use of two software tools, CONTAM, developed by the National Institute of Standards and Technology (NIST), and Visual Sample Plan (VSP), developed by Pacific Northwest National Laboratory (PNNL). The CONTAM modeling software was used to virtually contaminate a model of the INL test building under various release and dissemination scenarios as well as a range of building design and operation parameters. The results of these CONTAM simulations were then used to investigate the relevance and performance of various sampling strategies using VSP. One of the fundamental outcomes of this project was the demonstration of how CONTAM and VSP can be used together to effectively develop sampling plans to support the various stages of response to an airborne chemical, biological, radiological, or nuclear event. Following such an event (or prior to an event), incident details and the conceptual site model could be used to create an ensemble of CONTAM simulations which model contaminant dispersion within a building. These predictions could then be used to identify priority area zones within the building and then sampling designs and strategies could be developed based on those zones.

Glenoid version and size: does gender, ethnicity, or body size play a role?

Science.gov (United States)

Piponov, Hristo Ivanov; Savin, David; Shah, Neal; Esposito, Domenic; Schwartz, Brian; Moretti, Vincent; Goldberg, Benjamin

2016-11-01

Variations in glenoid morphology among patients of different gender, body habitus, and ethnicity have been of interest for surgeons. Understanding these anatomical variations is a critical step in restoring normal glenohumeral structure during shoulder reconstruction surgery. Retrospective review of 108 patient shoulder CT scans was performed and glenoid version, AP diameter and height were measured. Statistical multiple regression models were used to investigate the ability of gender and ethnicity to predict glenoid AP diameter, height, and version independently of patient weight and height. The mean glenoid AP diameter was 24.7 ± 3.5, the mean glenoid height was 31.7 ± 3.7, and the mean glenoid version was 0.05 ± 9.05. According to our regression models, males would be expected to exhibit 8.4° more glenoid retroversion than females (p = 0.003) and have 2.9 mm larger glenoid height compared to females (p = 0.002). The predicted male glenoid AP diameter was 3.4 mm higher than that in females (p variations in glenoid size and version are observed among ethnicities, larger sample size ethnic groups will be necessary to explore the precise relations. Surgeons should consider gender and ethnic variations in the pre-operative planning and surgical restoration of the native glenohumeral relationship. Anatomic Study.

Students' online collaborative intention for group projects: Evidence from an extended version of the theory of planned behaviour.

Science.gov (United States)

Cheng, Eddie W L; Chu, Samuel K W

2016-08-01

Given the increasing use of web technology for teaching and learning, this study developed and examined an extended version of the theory of planned behaviour (TPB) model, which explained students' intention to collaborate online for their group projects. Results indicated that past experience predicted the three antecedents of intention, while past behaviour was predictive of subjective norm and perceived behavioural control. Moreover, the three antecedents (attitude towards e-collaboration, subjective norm and perceived behavioural control) were found to significantly predict e-collaborative intention. This study explored the use of the "remember" type of awareness (i.e. past experience) and evaluated the value of the "know" type of awareness (i.e. past behaviour) in the TPB model. © 2015 International Union of Psychological Science.

40 CFR Appendix Xi to Part 86 - Sampling Plans for Selective Enforcement Auditing of Light-Duty Vehicles

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Sampling Plans for Selective Enforcement Auditing of Light-Duty Vehicles XI Appendix XI to Part 86 Protection of Environment ENVIRONMENTAL... Enforcement Auditing of Light-Duty Vehicles 40% AQL Table 1—Sampling Plan Code Letter Annual sales of...

Resource Conservation and Recovery Act industrial site environmental restoration site characterization plan: Area 23, Building 650 Leachfield

International Nuclear Information System (INIS)

1997-03-01

This plan presents the strategy for the characterization of Corrective Action Unit 94, Area 23, Building 650 Leachfield. It is a land disposal unit, located southeast of Building 650, that was in operation from 1965 to October 1992, with an estimated annual discharge rate of less than 984 liters from designated sinks, floor drains, and emergency decontamination showers in Building 650. The objectives of the planned activities are to: obtain sufficient sample analytical data from which further assessment, remediation, and/or closure strategies may be developed for the site: and obtain sufficient sample analytical data for management of investigation-derived waste (IDW). All references to regulations in this plan are to the versions of the regulations that are current at the time of publication of this plan. The scope of the characterization will include subsurface soil boring (i.e., drilling), in situ sampling of the soil within subsurface soil borings, and sample analysis for both site characterization and waste management purposes

Itil version 3 at a glance information quick reference

CERN Document Server

Long, John

2008-01-01

ITILA(R) Version 3 At a Glance takes a graphical approach to consolidating the information of ITILA(R) version 3. ITILA(R) is an internationally-recognized set of best practices for providing IT service management. IT organizations worldwide are implementing ITILA(R) as a vehicle for improving IT service quality and improve return on investment for IT services. The desk referencea (TM)s unique graphical approach will take otherwise complex textual descriptions and make the information accessible in a series of consistent, simple diagrams. ITILA(R) Version 3 At a Glance will be of interest to organizations looking to train their staffs in a consistent and cost-effective way. Further, this book is ideal for anyone involved in planning consulting, implementing, or testing an ITILA(R) Version 3 implementation. Each chapter in ITILA(R) Version 3 at a Glance summarizes one of the ITILA(R) v3 books in the following consistent structure: - Brief Description of the Stage - Overview Diagram of the Stage - Key Concepts ...

Global Threat Reduction Initiative Fuel Thermo-Physical Characterization Project: Sample Management Plan

Energy Technology Data Exchange (ETDEWEB)

Casella, Amanda J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pereira, Mario M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Steen, Franciska H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2013-01-01

This sample management plan provides guidelines for sectioning, preparation, acceptance criteria, analytical path, and end-of-life disposal for the fuel element segments utilized in the Global Threat Reduction Initiative (GTRI), Fuel Thermo-Physical Characterization Project. The Fuel Thermo-Physical Characterization Project is tasked with analysis of irradiated Low Enriched Uranium (LEU) Molybdenum (U-Mo) fuel element samples to support the GTRI conversion program. Sample analysis may include optical microscopy (OM), scanning electron microscopy (SEM) fuel-surface interface analysis, gas pycnometry (density) measurements, laser flash analysis (LFA), differential scanning calorimetry (DSC), thermogravimetry and differential thermal analysis with mass spectroscopy (TG /DTA-MS), Inductively Coupled Plasma Spectrophotometry (ICP), alpha spectroscopy, and Thermal Ionization Mass Spectroscopy (TIMS). The project will utilize existing Radiochemical Processing Laboratory (RPL) operating, technical, and administrative procedures for sample receipt, processing, and analyses. Test instructions (TIs), which are documents used to provide specific details regarding the implementation of an existing RPL approved technical or operational procedure, will also be used to communicate to staff project specific parameters requested by the Principal Investigator (PI). TIs will be developed, reviewed, and issued in accordance with the latest revision of the RPL-PLN-700, RPL Operations Plan. Additionally, the PI must approve all project test instructions and red-line changes to test instructions.

An ultra-short screening version of the Recalled Parental Rearing Behavior questionnaire (FEE-US and its factor structure in a representative German sample

Directory of Open Access Journals (Sweden)

Petrowski Katja

2012-11-01

Full Text Available Abstract Background The Recalled Parental Rearing Behavior questionnaire (FEE, [1,2] assesses perceived parental rearing behavior separately for each parent. An ultra-short screening version (FEE-US with the same three scales each for the mother and the father is reported and factor-analytically validated. Methods N = 4,640 subjects aged 14 to 92 (M = 48.4 years were selected by the random-route sampling method. The ultra-short questionnaire version was derived from the long version through item and factor analyses. In a confirmatory factor analysis framework, the hypothesized three-factorial structure was fitted to the empirical data and tested for measurement invariance, differential item functioning, item discriminability, and convergent and discriminant factorial validity. Effects of gender or age were assessed using MANOVAs. Results The a-priori hypothesized model resulted in mostly adequate overall fit. Neither gender nor age group yielded considerable effects on the factor structure, but had small effects on means of raw score sums. Factorial validities could be confirmed. Scale sums are well-suited to rank respondents along the respective latent dimension. Conclusion The structure of the long version with the factors Rejection & Punishment, Emotional Warmth, and Control & Overprotection could be replicated for both father and mother items in the ultra-short screening version using confirmatory factor analyses. These results indicate that the ultra-short screening version is a time-saving and promising screening instrument for research settings and in individual counseling. However, the shortened scales do not necessarily represent the full spectrum covered by the full-scale dimensions.

APS beamline standard components handbook, Version 1.3

International Nuclear Information System (INIS)

Hahn, U.; Shu, D.; Kuzay, T.M.

1993-02-01

This Handbook in its current version (1.3) contains descriptions, specifications, and preliminary engineering design drawings for many of the standard components. The design status and schedules have been provided wherever possible. In the near future, the APS plans to update engineering drawings of identified standard beamline components and complete the Handbook. The completed version of this Handbook will become available to both the CATs and potential vendors. Use of standard components should result in major cost reductions for CATs in the areas of beamline design and construction

Tank 241-SY-101 push mode core sampling and analysis plan

International Nuclear Information System (INIS)

CONNER, J.M.

1998-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for push mode core samples from tank 241-SY-101 (SY-101). It is written in accordance with Data Quality Objective to Support Resolution of the Flammable Gas Safety Issue (Bauer 1998), Low Activity Waste Feed Data Quality Objectives (Wiemers and Miller 1997 and DOE 1998), Data Quality Objectives for TWRS Privatization Phase I: Confirm Tank T is an Appropriate Feed Source for Low-Activity Waste Feed Batch X (Certa 1998), and the Tank Safety Screening Data Quality Objective (Dukelow et al. 1995). The Tank Characterization Technical Sampling Basis document (Brown et al. 1998) indicates that these issues apply to tank SY-101 for this sampling event. Brown et al. also identifies high-level waste, regulatory, pretreatment and disposal issues as applicable issues for this tank. However, these issues will not be addressed via this sampling event

Version pressure feedback mechanisms for speculative versioning caches

Science.gov (United States)

Eichenberger, Alexandre E.; Gara, Alan; O& #x27; Brien, Kathryn M.; Ohmacht, Martin; Zhuang, Xiaotong

2013-03-12

Mechanisms are provided for controlling version pressure on a speculative versioning cache. Raw version pressure data is collected based on one or more threads accessing cache lines of the speculative versioning cache. One or more statistical measures of version pressure are generated based on the collected raw version pressure data. A determination is made as to whether one or more modifications to an operation of a data processing system are to be performed based on the one or more statistical measures of version pressure, the one or more modifications affecting version pressure exerted on the speculative versioning cache. An operation of the data processing system is modified based on the one or more determined modifications, in response to a determination that one or more modifications to the operation of the data processing system are to be performed, to affect the version pressure exerted on the speculative versioning cache.

Soil sampling and analysis plan for the 3718-F Alkali Metal Treatment and Storage Facility closure activities

Energy Technology Data Exchange (ETDEWEB)

Sonnichsen, J.C.

1997-05-01

Amendment V.13.B.b to the approved closure plan (DOE-RL 1995a) requires that a soil sampling and analysis plan be prepared and submitted to the Washington State Department of Ecology (Ecology) for review and approval. Amendment V.13.B.c requires that a diagram of the 3718-F Alkali Metal Treatment and Storage Facility unit (the treatment, storage, and disposal [TSD] unit) boundary that is to be closed, including the maximum extent of operation, be prepared and submitted as part is of the soil sampling and analysis plan. This document describes the sampling and analysis that is to be performed in response to these requirements and amends the closure plan. Specifically, this document supersedes Section 6.2, lines 43--46, and Section 7.3.6 of the closure plan. Results from the analysis will be compared to cleanup levels identified in the closure plan. These cleanup levels will be established using residential exposure assumptions in accordance with the Model Toxics Control Act (MTCA) Cleanup Regulation (Washington Administrative Code [WAC] 173-340) as required in Amendment V.13.B.I. Results of all sampling, including the raw analytical data, a summary of analytical results, a data validation package, and a narrative summary with conclusions will be provided to Ecology as specified in Amendment V.13.B.e. The results and process used to collect and analyze the soil samples will be certified by a licensed professional engineer. These results and a certificate of closure for the balance of the TSD unit, as outlined in Chapter 7.0 of the approved closure plan (storage shed, concrete pad, burn building, scrubber, and reaction tanks), will provide the basis for a closure determination.

Soil sampling and analysis plan for the 3718-F Alkali Metal Treatment and Storage Facility closure activities

International Nuclear Information System (INIS)

Sonnichsen, J.C.

1997-01-01

Amendment V.13.B.b to the approved closure plan (DOE-RL 1995a) requires that a soil sampling and analysis plan be prepared and submitted to the Washington State Department of Ecology (Ecology) for review and approval. Amendment V.13.B.c requires that a diagram of the 3718-F Alkali Metal Treatment and Storage Facility unit (the treatment, storage, and disposal [TSD] unit) boundary that is to be closed, including the maximum extent of operation, be prepared and submitted as part is of the soil sampling and analysis plan. This document describes the sampling and analysis that is to be performed in response to these requirements and amends the closure plan. Specifically, this document supersedes Section 6.2, lines 43--46, and Section 7.3.6 of the closure plan. Results from the analysis will be compared to cleanup levels identified in the closure plan. These cleanup levels will be established using residential exposure assumptions in accordance with the Model Toxics Control Act (MTCA) Cleanup Regulation (Washington Administrative Code [WAC] 173-340) as required in Amendment V.13.B.I. Results of all sampling, including the raw analytical data, a summary of analytical results, a data validation package, and a narrative summary with conclusions will be provided to Ecology as specified in Amendment V.13.B.e. The results and process used to collect and analyze the soil samples will be certified by a licensed professional engineer. These results and a certificate of closure for the balance of the TSD unit, as outlined in Chapter 7.0 of the approved closure plan (storage shed, concrete pad, burn building, scrubber, and reaction tanks), will provide the basis for a closure determination

The Cost Implications in Ontario, Alberta, and British Columbia of Early Versus Delayed External Cephalic Version in the Early External Cephalic Version 2 (EECV2) Trial.

Science.gov (United States)

Ahmed, Rashid J; Gafni, Amiram; Hutton, Eileen K

2016-03-01

According to the Early External Cephalic Version (EECV2) Trial, planning external cephalic version (ECV) early in pregnancy results in fewer breech presentations at delivery compared with delayed external cephalic version. A Cochrane review conducted after the EECV2 Trial identified an increase in preterm birth associated with early ECV. We examined whether a policy of routine early ECV (i.e., before 37 weeks' gestation) is more or less costly than a policy of delayed ECV. We undertook this analysis from the perspective of a third-party payer (Ministry of Health). We applied data, using resources reported in the EECV2 Trial, to the Canadian context using 10 hospital unit costs and 17 physician service/procedure unit costs. The data were derived from the provincial health insurance plan schedule of medical benefits in three Canadian provinces (Ontario, Alberta, and British Columbia). The difference in mean total costs between study groups was tested for each province separately. We found that planning early ECV results in higher costs than planning delayed ECV. The mean costs of all physician services/procedures and hospital units for planned ECV compared with delayed ECV were $7997.32 versus $7263.04 in Ontario (P < 0.001), $8162.82 versus $7410.55 in Alberta (P < 0.001), and $8178.92 versus $7417.04 in British Columbia (P < 0.001), respectively. From the perspective of overall cost, our analyses do not support a policy of routinely planning ECV before 37 weeks' gestation. Copyright © 2016 The Society of Obstetricians and Gynaecologists of Canada/La Société des obstétriciens et gynécologues du Canada. Published by Elsevier Inc. All rights reserved.

Psychometric properties and validation of the Italian version of the Family Assessment Measure Third Edition - Short Version - in a nonclinical sample.

Science.gov (United States)

Pellerone, Monica; Ramaci, Tiziana; Parrello, Santa; Guariglia, Paola; Giaimo, Flavio

2017-01-01

Family functioning plays an important role in developing and maintaining dysfunctional behaviors, especially during adolescence. The lack of indicators of family functioning, as determinants of personal and interpersonal problems, represents an obstacle to the activities aimed at developing preventive and intervention strategies. The Process Model of Family Functioning provides a conceptual framework organizing and integrating various concepts into a comprehensive family assessment; this model underlines that through the process of task accomplishment, each family meets objectives central to its life as a group. The Family Assessment Measure Third Edition (FAM III), based on the Process Model of Family Functioning, is among the most frequently used self-report instruments to measure family functioning. The present study aimed to evaluate the psychometric properties of the Italian version of the Family Assessment Measure Third Edition - Short Version (Brief FAM-III). It consists of three modules: General Scale, which evaluates the family as a system; Dyadic Relationships Scale, which examines how each family member perceives his/her relationship with another member; and Self-Rating Scale, which indicates how each family member is perceived within the nucleus. The developed Brief FAM-III together with the Family Assessment Device were administered to 484 subjects, members of 162 Italian families, formed of 162 fathers aged between 35 and 73 years; 162 mothers aged between 34 and 69 years; and 160 children aged between 12 and 35 years. Correlation, paired-sample t -test, and reliability analyses were carried out. General item analysis shows good indices of reliability with Cronbach's α coefficients equal to 0.96. The Brief FAM-III has satisfactory internal consistency, with Cronbach's α equal to 0.90 for General Scale, 0.94 for Dyadic Relationships Scale, and 0.88 for the Self-Rating Scale. The Brief FAM-III can be a psychometrically reliable and valid measure for

Tank 241-AZ-101 Mixer Pump Test Vapor Sampling and Analysis Plan

International Nuclear Information System (INIS)

TEMPLETON, A.M.

2000-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for vapor samples obtained during the operation of mixer pumps in tank 241-AZ-101. The primary purpose of the mixer pump test (MPT) is to demonstrate that the two 300 horsepower mixer pumps installed in tank 241-AZ-101 can mobilize the settled sludge so that it can be retrieved for treatment and vitrification. Sampling will be performed in accordance with Tank 241-AZ-101 Mixer Pump Test Data Quality Objective (Banning 1999) and Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis (Mulkey 1999). The sampling will verify if current air emission estimates used in the permit application are correct and provide information for future air permit applications

Sampling and Analysis Plan Update for Groundwater Monitoring 1100-EM-1 Operable Unit

International Nuclear Information System (INIS)

DR Newcomer

1999-01-01

This document updates the sampling and analysis plan (Department of Energy/Richland Operations--95-50) to reflect current groundwater monitoring at the 1100-EM-1Operable Unit. Items requiring updating included sampling and analysis protocol, quality assurance and quality control, groundwater level measurement procedure, and data management. The plan covers groundwater monitoring, as specified in the 1993 Record of Decision, during the 5-year review period from 1995 through 1999. Following the 5-year review period, groundwater-monitoring data will be reviewed by Environmental Protection Agency to evaluate the progress of natural attenuation of trichloroethylene. Monitored natural attenuation and institutional controls for groundwater use at the inactive Horn Rapids Landfill was the selected remedy specified in the Record of Decision

Advanced communications technology satellite high burst rate link evaluation terminal power control and rain fade software test plan, version 1.0

Science.gov (United States)

Reinhart, Richard C.

1993-01-01

The Power Control and Rain Fade Software was developed at the NASA Lewis Research Center to support the Advanced Communications Technology Satellite High Burst Rate Link Evaluation Terminal (ACTS HBR-LET). The HBR-LET is an experimenters terminal to communicate with the ACTS for various experiments by government, university, and industry agencies. The Power Control and Rain Fade Software is one segment of the Control and Performance Monitor (C&PM) Software system of the HBR-LET. The Power Control and Rain Fade Software automatically controls the LET uplink power to compensate for signal fades. Besides power augmentation, the C&PM Software system is also responsible for instrument control during HBR-LET experiments, control of the Intermediate Frequency Switch Matrix on board the ACTS to yield a desired path through the spacecraft payload, and data display. The Power Control and Rain Fade Software User's Guide, Version 1.0 outlines the commands and procedures to install and operate the Power Control and Rain Fade Software. The Power Control and Rain Fade Software Maintenance Manual, Version 1.0 is a programmer's guide to the Power Control and Rain Fade Software. This manual details the current implementation of the software from a technical perspective. Included is an overview of the Power Control and Rain Fade Software, computer algorithms, format representations, and computer hardware configuration. The Power Control and Rain Fade Test Plan provides a step-by-step procedure to verify the operation of the software using a predetermined signal fade event. The Test Plan also provides a means to demonstrate the capability of the software.

Fixed-Precision Sequential Sampling Plans for Estimating Alfalfa Caterpillar, Colias lesbia, Egg Density in Alfalfa, Medicago sativa, Fields in Córdoba, Argentina

Science.gov (United States)

Serra, Gerardo V.; Porta, Norma C. La; Avalos, Susana; Mazzuferi, Vilma

2013-01-01

The alfalfa caterpillar, Colias lesbia (Fabricius) (Lepidoptera: Pieridae), is a major pest of alfalfa, Medicago sativa L. (Fabales: Fabaceae), crops in Argentina. Its management is based mainly on chemical control of larvae whenever the larvae exceed the action threshold. To develop and validate fixed-precision sequential sampling plans, an intensive sampling programme for C. lesbia eggs was carried out in two alfalfa plots located in the Province of Córdoba, Argentina, from 1999 to 2002. Using Resampling for Validation of Sampling Plans software, 12 additional independent data sets were used to validate the sequential sampling plan with precision levels of 0.10 and 0.25 (SE/mean), respectively. For a range of mean densities of 0.10 to 8.35 eggs/sample, an average sample size of only 27 and 26 sample units was required to achieve a desired precision level of 0.25 for the sampling plans of Green and Kuno, respectively. As the precision level was increased to 0.10, average sample size increased to 161 and 157 sample units for the sampling plans of Green and Kuno, respectively. We recommend using Green's sequential sampling plan because it is less sensitive to changes in egg density. These sampling plans are a valuable tool for researchers to study population dynamics and to evaluate integrated pest management strategies. PMID:23909840

Savannah River Site sample and analysis plan for Clemson Technical Center waste

International Nuclear Information System (INIS)

Hagstrom, T.

1998-04-01

The purpose of this sampling and analysis plan is to determine the chemical, physical and radiological properties of the SRS radioactive Polychlorinated Biphenyl (PCB) liquid waste stream, to verify that it conforms to Waste Acceptance Criteria of the Department of Energy (DOE) East Tennessee Technology Park (ETTP) Toxic Substance Control Act (TSCA) Incineration Facility. Waste being sent to the ETTP TSCA Incinerator for treatment must be sufficiently characterized to ensure that the waste stream meets the waste acceptance criteria to ensure proper handling, classification, and processing of incoming waste to meet the Waste Storage and Treatment Facility's Operating Permits. This sampling and analysis plan is limited to WSRC container(s) of homogeneous or multiphasic radioactive PCB contaminated liquids generated in association with a treatability study at Clemson Technical Center (CTC) and currently stored at the WSRC Solid Waste Division Mixed Waste Storage Facility (MWSF)

241-Z-361 Sludge Characterization Sampling and Analysis Plan

Energy Technology Data Exchange (ETDEWEB)

BANNING, D.L.

1999-08-05

This sampling and analysis plan (SAP) identifies the type, quantity, and quality of data needed to support characterization of the sludge that remains in Tank 241-2-361. The procedures described in this SAP are based on the results of the 241-2-361 Sludge Characterization Data Quality Objectives (DQO) (BWHC 1999) process for the tank. The primary objectives of this project are to evaluate the contents of Tank 241-2-361 in order to resolve safety and safeguards issues and to assess alternatives for sludge removal and disposal.

241-Z-361 Sludge Characterization Sampling and Analysis Plan

Energy Technology Data Exchange (ETDEWEB)

BANNING, D.L.

1999-07-29

This sampling and analysis plan (SAP) identifies the type, quantity, and quality of data needed to support characterization of the sludge that remains in Tank 241-2-361. The procedures described in this SAP are based on the results of the 241-2-361 Sludge Characterization Data Quality Objectives (DQO) (BWHC 1999) process for the tank. The primary objectives of this project are to evaluate the contents of Tank 241-2-361 in order to resolve safety and safeguards issues and to assess alternatives for sludge removal and disposal.

Sampling and analysis plan for the consolidated sludge samples from the canisters and floor of the 105-K East basin

International Nuclear Information System (INIS)

BAKER, R.B.

1999-01-01

This Sampling and Analysis Plan (SAP) provides direction for sampling of fuel canister and floor Sludge from the K East Basin to complete the inventory of samples needed for Sludge treatment process testing. Sample volumes and sources consider recent reviews made by the Sludge treatment subproject. The representative samples will be characterized to the extent needed for the material to be used effectively for testing. Sampling equipment used allows drawing of large volume sludge samples and consolidation of sample material from a number of basin locations into one container. Once filled, the containers will be placed in a cask and transported to Hanford laboratories for recovery and evaluation. Included in the present SAP are the logic for sample location selection, laboratory analysis procedures required, and reporting needed to meet the Data Quality Objectives (DQOs) for this initiative

Tracer gas diffusion sampling test plan

International Nuclear Information System (INIS)

Rohay, V.J.

1993-01-01

Efforts are under way to employ active and passive vapor extraction to remove carbon tetrachloride from the soil in the 200 West Area an the Hanford Site as part of the 200 West Area Carbon Tetrachloride Expedited Response Action. In the active approach, a vacuum is applied to a well, which causes soil gas surrounding the well to be drawn up to the surface. The contaminated air is cleaned by passage through a granular activated carbon bed. There are questions concerning the radius of influence associated with application of the vacuum system and related uncertainties about the soil-gas diffusion rates with and without the vacuum system present. To address these questions, a series of tracer gas diffusion sampling tests is proposed in which an inert, nontoxic tracer gas, sulfur hexafluoride (SF 6 ), will be injected into a well, and the rates of SF 6 diffusion through the surrounding soil horizon will be measured by sampling in nearby wells. Tracer gas tests will be conducted at sites very near the active vacuum extraction system and also at sites beyond the radius of influence of the active vacuum system. In the passive vapor extraction approach, barometric pressure fluctuations cause soil gas to be drawn to the surface through the well. At the passive sites, the effects of barometric ''pumping'' due to changes in atmospheric pressure will be investigated. Application of tracer gas testing to both the active and passive vapor extraction methods is described in the wellfield enhancement work plan (Rohay and Cameron 1993)

Engineering task plan for the development, fabrication and installation of rotary mode core sample truck bellows

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

The Rotary Mode Core Sampling Trucks (RMSCTs) currently use a multi-sectioned bellows between the grapple box and the quill rod to compensate for drill head motion and to provide a path for purge gas. The current bellows, which is detailed on drawing H-2-690059, is expensive to procure, has a lengthy procurement cycle, and is prone to failure. Therefore, a task has been identified to design, fabricate, and install a replacement bellows. This Engineering Task Plan (ETP) is the management plan document for accomplishing the identified tasks. Any changes in scope of the ETP shall require formal direction by the Characterization Engineering manager. This document shall also be considered the work planning document for developmental control per Development Control Requirements (HNF 1999a). This Engineering Task Plan (ETP) is the management plan document for accomplishing the design, fabrication, and installation of a replacement bellows assembly for the Rotary Mode Core Sampling Trucks 3 and 4 (RMCST)

DOE responses to Ecology review comments for ''Sampling and analysis plans for the 100-D Ponds voluntary remediation project''

International Nuclear Information System (INIS)

1996-01-01

The Sampling and Analysis Plan describes the sampling and analytical activities which will be performed to support closure of the 100-D Ponds at the Hanford Reservation. This report contains responses by the US Department of Energy to Ecology review for ''Sampling and Analysis Plan for the 100-D Ponds Voluntary Remediation Project.''

Code for plant identification (KKS) key in PC version. KKS-Schluessel-Programm in PC-Version

Energy Technology Data Exchange (ETDEWEB)

Pannenbaecker, K. (GABO Gesellschaft fuer Ablauforganisation und Informationsverarbeitung mbH, Erlangen (Germany) GABO Gesellschaft fuer Ablauforganisation und Informationsverarbeitung mbH, Muenchen (Germany))

1991-11-01

The plant identification system (KKS) as a common development of german plant operators, erection firms and also power plant oriented organisations have decisively influenced the technical-organizing activities of planning and erections as operations and maintenance of all kind of power plants. Fundamentals are three key parts, operation, armatures and function keys. Their management and application is executed by a plantidentification-key code in a PC version, which is briefly described in this report. (orig.).

2017 Annual Terrestrial Sampling Plan for Sandia National Laboratories/New Mexico on Kirtland Air Force Base

Energy Technology Data Exchange (ETDEWEB)

Griffith, Stacy R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-02-01

The 2017 Annual Terrestrial Sampling Plan for Sandia National Laboratories/New Mexico on Kirtland Air Force Base has been prepared in accordance with the “Letter of Agreement Between Department of Energy, National Nuclear Security Administration, Sandia Field Office (DOE/NNSA/SFO) and 377th Air Base Wing (ABW), Kirtland Air Force Base (KAFB) for Terrestrial Sampling” (signed January 2017), Sandia National Laboratories, New Mexico (SNL/NM). The Letter of Agreement requires submittal of an annual terrestrial sampling plan.

2018 Annual Terrestrial Sampling Plan for Sandia National Laboratories/New Mexico on Kirtland Air Force Base.

Energy Technology Data Exchange (ETDEWEB)

Griffith, Stacy R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-01-01

The 2018 Annual Terrestrial Sampling Plan for Sandia National Laboratories/New Mexico on Kirtland Air Force Base has been prepared in accordance with the “Letter of Agreement Between Department of Energy, National Nuclear Security Administration, Sandia Field Office (DOE/NNSA/SFO) and 377th Air Base Wing (ABW), Kirtland Air Force Base (KAFB) for Terrestrial Sampling” (signed January 2017), Sandia National Laboratories, New Mexico (SNL/NM). The Letter of Agreement requires submittal of an annual terrestrial sampling plan.

The French Version of the Screen for Child Anxiety Related Emotional Disorders-Revised (Scared-R: Factor Structure, Convergent and Divergent Validity in a Sample of Teenagers

Directory of Open Access Journals (Sweden)

Martine Bouvard

2013-06-01

Full Text Available The principal objective of this study is to provide data on the French version of the SCARED-R. This article investigates the factor structure of the French version of the Screen for Child Anxiety Related Emotional Disorders-Revised (SCARED-R and its convergent and divergent validity. 704 normal adolescents aged 10 to 19 years completed the questionnaires in their classrooms. A sub-sample of 595 adolescents also completed an anxiety questionnaire (the French version of the Fear Survey Schedule for Children-Revised, FSSC-R and a depression questionnaire (the French version of the Center for Epidemiological Studies Depression Scale, CES-D. Confirmatory factor analysis of the SCARED-R suggested reasonable fit for the 9-factor model. The comparison of the convergent and divergent validity revealed that the SCARED-R total score and five SCARED-R subscales (SAD, Social Phobia and the three Specific Phobias correlated more strongly with anxiety than depression. The other SCARED-R subscales (GAD, Panic Disorder, OCD and PTSD are positively related to levels of anxiety and depression. Altogether, the French version of the SCARED-R showed reasonable psychometric properties.

Sampling and Analysis Plan for Verification Sampling of LANL-Derived Residual Radionuclides in Soils within Tract A-18-2 for Land Conveyance

Energy Technology Data Exchange (ETDEWEB)

Ruedig, Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-08-30

Public Law 105-119 directs the U.S. Department of Energy (DOE) to convey or transfer parcels of land to the Incorporated County of Los Alamos or their designees and to the Department of Interior, Bureau of Indian Affairs, in trust for the Pueblo de San Ildefonso. Los Alamos National Security is tasked to support DOE in conveyance and/or transfer of identified land parcels no later than September 2022. Under DOE Order 458.1, Radiation Protection of the Public and the Environment (O458.1, 2013) and Los Alamos National Laboratory (LANL or the Laboratory) implementing Policy 412 (P412, 2014), real property with the potential to contain residual radioactive material must meet the criteria for clearance and release to the public. This Sampling and Analysis Plan (SAP) is a second investigation of Tract A-18-2 for the purpose of verifying the previous sampling results (LANL 2017). This sample plan requires 18 projectspecific soil samples for use in radiological clearance decisions consistent with LANL Procedure ENV-ES-TP-238 (2015a) and guidance in the Multi-Agency Radiation Survey and Site Investigation Manual (MARSSIM, 2000). The sampling work will be conducted by LANL, and samples will be evaluated by a LANL-contracted independent lab. However, there will be federal review (verification) of all steps of the sampling process.

Comprehensive work plan and health and safety plan for the 7500 Area Contamination Site sampling at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Burman, S.N.; Landguth, D.C.; Uziel, M.S.; Hatmaker, T.L.; Tiner, P.F.

1992-05-01

As part of the Environmental Restoration Program sponsored by the US Department of Energy's Office of Environmental Restoration and Waste Management, this plan has been developed for the environmental sampling efforts at the 7500 Area Contamination Site, Oak Ridge National Laboratory (ORNL), Oak Ridge, Tennessee. This plan was developed by the Measurement Applications and Development Group (MAD) of the Health and Safety Research Division of ORNL and will be implemented by ORNL/MAD. Major components of the plan include (1) a quality assurance project plan that describes the scope and objectives of ORNL/MAD activities at the 7500 Area Contamination Site, assigns responsibilities, and provides emergency information for contingencies that may arise during field operations; (2) sampling and analysis sections; (3) a site-specific health and safety section that describes general site hazards, hazards associated with specific tasks, personnel protection requirements, and mandatory safety procedures; (4) procedures and requirements for equipment decontamination and responsibilities for generated wastes, waste management, and contamination control; and (5) a discussion of form completion and reporting required to document activities at the 7500 Area Contamination Site

Comprehensive work plan and health and safety plan for the 7500 Area Contamination Site sampling at Oak Ridge National Laboratory, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

Burman, S.N.; Landguth, D.C.; Uziel, M.S.; Hatmaker, T.L.; Tiner, P.F.

1992-05-01

As part of the Environmental Restoration Program sponsored by the US Department of Energy's Office of Environmental Restoration and Waste Management, this plan has been developed for the environmental sampling efforts at the 7500 Area Contamination Site, Oak Ridge National Laboratory (ORNL), Oak Ridge, Tennessee. This plan was developed by the Measurement Applications and Development Group (MAD) of the Health and Safety Research Division of ORNL and will be implemented by ORNL/MAD. Major components of the plan include (1) a quality assurance project plan that describes the scope and objectives of ORNL/MAD activities at the 7500 Area Contamination Site, assigns responsibilities, and provides emergency information for contingencies that may arise during field operations; (2) sampling and analysis sections; (3) a site-specific health and safety section that describes general site hazards, hazards associated with specific tasks, personnel protection requirements, and mandatory safety procedures; (4) procedures and requirements for equipment decontamination and responsibilities for generated wastes, waste management, and contamination control; and (5) a discussion of form completion and reporting required to document activities at the 7500 Area Contamination Site.

Development of the unified version of COBRA/RELAP5

Energy Technology Data Exchange (ETDEWEB)

Jeong, J J; Ha, K S; Chung, B D; Lee, W J; Sim, S K [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1998-12-31

The COBRA/RELAP5 code, an integrated version of the COBRA-TF and RELAP5/MOD3 codes, has been developed for the realistic simulations of complicated, multi-dimensional, two-phase, thermal-hydraulic system transients in light water reactors. Recently, KAERI developed an unified version of the COBRA/RELAP5 code, which can run in serial mode on both workstations and personal computers. This paper provides the brief overview of the code integration scheme, the recent code modifications, the developmental assessments, and the future development plan. 13 refs., 5 figs., 2 tabs. (Author)

Development of the unified version of COBRA/RELAP5

Energy Technology Data Exchange (ETDEWEB)

Jeong, J. J.; Ha, K. S.; Chung, B. D.; Lee, W. J.; Sim, S. K. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1997-12-31

The COBRA/RELAP5 code, an integrated version of the COBRA-TF and RELAP5/MOD3 codes, has been developed for the realistic simulations of complicated, multi-dimensional, two-phase, thermal-hydraulic system transients in light water reactors. Recently, KAERI developed an unified version of the COBRA/RELAP5 code, which can run in serial mode on both workstations and personal computers. This paper provides the brief overview of the code integration scheme, the recent code modifications, the developmental assessments, and the future development plan. 13 refs., 5 figs., 2 tabs. (Author)

Tank 241-Z-361 vapor sampling and analysis plan

Energy Technology Data Exchange (ETDEWEB)

BANNING, D.L.

1999-02-23

Tank 241-Z-361 is identified in the Hanford Federal Facility Agreement and Consent Order (commonly referred to as the Tri-Party Agreement), Appendix C, (Ecology et al. 1994) as a unit to be remediated under the authority of the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). As such, the U.S. Environmental Protection Agency will serve as the lead regulatory agency for remediation of this tank under the CERCLA process. At the time this unit was identified as a CERCLA site under the Tri-Party Agreement, it was placed within the 200-ZP-2 Operable Unit. In 1997, The Tri-parties redefined 200 Area Operable Units into waste groupings (Waste Site Grouping for 200 Areas Soils Investigations [DOE-RL 1992 and 1997]). A waste group contains waste sites that share similarities in geological conditions, function, and types of waste received. Tank 241-Z-361 is identified within the CERCLA Plutonium/Organic-rich Process Condensate/Process Waste Group (DOE-RL 1992). The Plutonium/Organic-rich Process Condensate/Process Waste Group has been prioritized for remediation beginning in the year 2004. Results of Tank 216-Z-361 sampling and analysis described in this Sampling and Analysis Plan (SAP) and in the SAP for sludge sampling (to be developed) will determine whether expedited response actions are required before 2004 because of the hazards associated with tank contents. Should data conclude that remediation of this tank should occur earlier than is planned for the other sites in the waste group, it is likely that removal alternatives will be analyzed in a separate Engineering Evaluation/Cost Analysis (EE/CA). Removal actions would proceed after the U.S. Environmental Protection Agency (EPA) signs an Action Memorandum describing the selected removal alternative for Tank 216-Z-361. If the data conclude that there is no immediate threat to human health and the environment from this tank, remedial actions for the tank will be defined in a

The Integrated Tiger Series version 5.0

International Nuclear Information System (INIS)

Laub, Th.W.; Kensek, R.P.; Franke, B.C.; Lorence, L.J.; Crawford, M.J.; Quirk, Th.J.

2005-01-01

The Integrated Tiger Series (ITS) is a powerful and user-friendly software package permitting Monte Carlo solution of linear time-independent coupled electron/photon radiation transport problems, with or without the presence of macroscopic electric and magnetic fields of arbitrary spatial dependence. The package contains programs to perform 1-, 2-, and 3-dimensional simulations. Improvements in the ITS code package since the release of version 3.0 include improved physics, multigroup and adjoint capabilities, Computer-Aided Design geometry tracking, parallel implementations of all ITS codes, and more automated sub-zoning capabilities. These improvements and others are described as current or planned development efforts. The ITS package is currently at version 5.0. (authors)

UMTRA project water sampling and analysis plan, Monument Valley, Arizona

International Nuclear Information System (INIS)

1994-04-01

The Monument Valley Uranium Mill Tailings Remedial Action (UMTRA) Project site in Cane Valley is a former uranium mill that has undergone surface remediation in the form of tailings and contaminated materials removal. Contaminated materials from the Monument Valley (Arizona) UMTRA Project site have been transported to the Mexican Hat (Utah) UMTRA Project site for consolidation with the Mexican Hat tailings. Tailings removal was completed in February 1994. Three geologic units at the site contain water: the unconsolidated eolian and alluvial deposits (alluvial aquifer), the Shinarump Conglomerate (Shinarump Member), and the De Chelly Sandstone. Water quality analyses indicate the contaminant plume has migrated north of the site and is mainly in the alluvial aquifer. An upward hydraulic gradient in the De Chelly Sandstone provides some protection to that aquifer. This water sampling and analysis plan recommends sampling domestic wells, monitor wells, and surface water in April and September 1994. The purpose of sampling is to continue periodic monitoring for the surface program, evaluate changes to water quality for site characterization, and provide data for the baseline risk assessment. Samples taken in April will be representative of high ground water levels and samples taken in September will be representative of low ground water levels. Filtered and nonfiltered samples will be analyzed for plume indicator parameters and baseline risk assessment parameters

Planning spatial sampling of the soil from an uncertain reconnaissance variogram

Science.gov (United States)

Lark, R. Murray; Hamilton, Elliott M.; Kaninga, Belinda; Maseka, Kakoma K.; Mutondo, Moola; Sakala, Godfrey M.; Watts, Michael J.

2017-12-01

An estimated variogram of a soil property can be used to support a rational choice of sampling intensity for geostatistical mapping. However, it is known that estimated variograms are subject to uncertainty. In this paper we address two practical questions. First, how can we make a robust decision on sampling intensity, given the uncertainty in the variogram? Second, what are the costs incurred in terms of oversampling because of uncertainty in the variogram model used to plan sampling? To achieve this we show how samples of the posterior distribution of variogram parameters, from a computational Bayesian analysis, can be used to characterize the effects of variogram parameter uncertainty on sampling decisions. We show how one can select a sample intensity so that a target value of the kriging variance is not exceeded with some specified probability. This will lead to oversampling, relative to the sampling intensity that would be specified if there were no uncertainty in the variogram parameters. One can estimate the magnitude of this oversampling by treating the tolerable grid spacing for the final sample as a random variable, given the target kriging variance and the posterior sample values. We illustrate these concepts with some data on total uranium content in a relatively sparse sample of soil from agricultural land near mine tailings in the Copperbelt Province of Zambia.

UMTRA project water sampling and analysis plan, Ambrosia Lake, New Mexico

International Nuclear Information System (INIS)

1994-02-01

This water sampling and analysis plan (WSAP) provides the basis for ground water sampling at the Ambrosia Lake Uranium Mill Tailings Remedial Action (UMTRA) Project site during fiscal year 1994. It identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the monitoring locations and will be updated annually. The Ambrosia Lake site is in McKinley County, New Mexico, about 40 kilometers (km) (25 miles [mi]) north of Grants, New Mexico, and 1.6 km (1 mi) east of New Mexico Highway 509 (Figure 1.1). The town closest to the tailings pile is San Mateo, about 16 km ( 10 mi) southeast (Figure 1.2). The former mill and tailings pile are in Section 28, and two holding ponds are in Section 33, Township 14 North, Range 9 West. The site is shown on the US Geological Survey (USGS) map (USGS, 1980). The site is approximately 2100 meters (m) (7000 feet [ft]) above sea level

Implementing reduced-risk integrated pest management in fresh-market cabbage: influence of sampling parameters, and validation of binomial sequential sampling plans for the cabbage looper (Lepidoptera Noctuidae).

Science.gov (United States)

Burkness, Eric C; Hutchison, W D

2009-10-01

Populations of cabbage looper, Trichoplusiani (Lepidoptera: Noctuidae), were sampled in experimental plots and commercial fields of cabbage (Brasicca spp.) in Minnesota during 1998-1999 as part of a larger effort to implement an integrated pest management program. Using a resampling approach and the Wald's sequential probability ratio test, sampling plans with different sampling parameters were evaluated using independent presence/absence and enumerative data. Evaluations and comparisons of the different sampling plans were made based on the operating characteristic and average sample number functions generated for each plan and through the use of a decision probability matrix. Values for upper and lower decision boundaries, sequential error rates (alpha, beta), and tally threshold were modified to determine parameter influence on the operating characteristic and average sample number functions. The following parameters resulted in the most desirable operating characteristic and average sample number functions; action threshold of 0.1 proportion of plants infested, tally threshold of 1, alpha = beta = 0.1, upper boundary of 0.15, lower boundary of 0.05, and resampling with replacement. We found that sampling parameters can be modified and evaluated using resampling software to achieve desirable operating characteristic and average sample number functions. Moreover, management of T. ni by using binomial sequential sampling should provide a good balance between cost and reliability by minimizing sample size and maintaining a high level of correct decisions (>95%) to treat or not treat.

Microbiological sampling plan based on risk classification to verify supplier selection and production of served meals in food service operation.

Science.gov (United States)

Lahou, Evy; Jacxsens, Liesbeth; Van Landeghem, Filip; Uyttendaele, Mieke

2014-08-01

Food service operations are confronted with a diverse range of raw materials and served meals. The implementation of a microbial sampling plan in the framework of verification of suppliers and their own production process (functionality of their prerequisite and HACCP program), demands selection of food products and sampling frequencies. However, these are often selected without a well described scientifically underpinned sampling plan. Therefore, an approach on how to set-up a focused sampling plan, enabled by a microbial risk categorization of food products, for both incoming raw materials and meals served to the consumers is presented. The sampling plan was implemented as a case study during a one-year period in an institutional food service operation to test the feasibility of the chosen approach. This resulted in 123 samples of raw materials and 87 samples of meal servings (focused on high risk categorized food products) which were analyzed for spoilage bacteria, hygiene indicators and food borne pathogens. Although sampling plans are intrinsically limited in assessing the quality and safety of sampled foods, it was shown to be useful to reveal major non-compliances and opportunities to improve the food safety management system in place. Points of attention deduced in the case study were control of Listeria monocytogenes in raw meat spread and raw fish as well as overall microbial quality of served sandwiches and salads. Copyright © 2014 Elsevier Ltd. All rights reserved.

TMI-2 accident evaluation program sample acquisition and examination plan. Executive summary

International Nuclear Information System (INIS)

Russell, M.L.; McCardell, R.K.; Broughton, J.M.

1985-12-01

The purpose of the TMI-2 Accident Evaluation Program Sample Acquisition and Examination (TMI-2 AEP SA and E) program is to develop and implement a test and inspection plan that completes the current-condition characterization of (a) the TMI-2 equipment that may have been damaged by the core damage events and (b) the TMI-2 core fission product inventory. The characterization program includes both sample acquisitions and examinations and in-situ measurements. Fission product characterization involves locating the fission products as well as determining their chemical form and determining material association

SERA: Simulation Environment for Radiotherapy Applications - Users Manual Version 1CO

International Nuclear Information System (INIS)

Venhuizen, James Robert; Wessol, Daniel Edward; Wemple, Charles Alan; Wheeler, Floyd J; Harkin, G. J.; Frandsen, M. W.; Albright, C. L.; Cohen, M.T.; Rossmeier, M.; Cogliati, J.J.

2002-01-01

This document is the user manual for the Simulation Environment for Radiotherapy Applications (SERA) software program developed for boron-neutron capture therapy (BNCT) patient treatment planning by researchers at the Idaho National Engineering and Environmental Laboratory (INEEL) and students and faculty at Montana State University (MSU) Computer Science Department. This manual corresponds to the final release of the program, Version 1C0, developed to run under the RedHat Linux Operating System (version 7.2 or newer) or the Solaris Operating System (version 2.6 or newer). SERA is a suite of command line or interactively launched software modules, including graphical, geometric reconstruction, and execution interface modules for developing BNCT treatment plans. The program allows the user to develop geometric models of the patient as derived from Computed Tomography (CT) and Magnetic Resonance Imaging (MRI) images, perform dose computation for these geometric models, and display the computed doses on overlays of the original images as three dimensional representations. This manual provides a guide to the practical use of SERA, but is not an exhaustive treatment of each feature of the code

SERA: Simulation Environment for Radiotherapy Applications - Users Manual Version 1CO

Energy Technology Data Exchange (ETDEWEB)

Venhuizen, James Robert; Wessol, Daniel Edward; Wemple, Charles Alan; Wheeler, Floyd J; Harkin, G. J.; Frandsen, M. W.; Albright, C. L.; Cohen, M.T.; Rossmeier, M.; Cogliati, J.J.

2002-06-01

This document is the user manual for the Simulation Environment for Radiotherapy Applications (SERA) software program developed for boron-neutron capture therapy (BNCT) patient treatment planning by researchers at the Idaho National Engineering and Environmental Laboratory (INEEL) and students and faculty at Montana State University (MSU) Computer Science Department. This manual corresponds to the final release of the program, Version 1C0, developed to run under the RedHat Linux Operating System (version 7.2 or newer) or the Solaris™ Operating System (version 2.6 or newer). SERA is a suite of command line or interactively launched software modules, including graphical, geometric reconstruction, and execution interface modules for developing BNCT treatment plans. The program allows the user to develop geometric models of the patient as derived from Computed Tomography (CT) and Magnetic Resonance Imaging (MRI) images, perform dose computation for these geometric models, and display the computed doses on overlays of the original images as three dimensional representations. This manual provides a guide to the practical use of SERA, but is not an exhaustive treatment of each feature of the code.

A sample lesson plan for the course English Composition II

Directory of Open Access Journals (Sweden)

Córdoba Cubillo, Patricia

2005-03-01

Full Text Available The goal of this article is to present a lesson plan and a series of sample tasks to help the instructors from the course English Composition II, at the School of Modern Languages from the University of Costa Rica, to guide students write an essay integrating the four skills: listening, speaking, reading, and writing. These activities will be a source of comprehensible input for the learners that will hopefully result in a good writing piece. El objetivo de este artículo es presentar un plan de lección y una serie de actividades que le ayudarán a los y las instructoras del curso Composición Inglesa II de la Escuela de Lenguas Modernas de la Universidad de Costa Rica a guiar a sus estudiantes a escribir un ensayo integrando las cuatro macro-destrezas, a saber comprensión auditiva, conversación, lectura y escritura. Mediante estas actividades se espera que los estudiantes elaboren un ensayo de calidad.

Tank 241-SX-105 rotary mode core sampling and analysis plan

International Nuclear Information System (INIS)

Simpson, B.C.

1998-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for rotary mode core samples from tank 241-SX-105 (SX-105). It is written in accordance with Tank Safety Screening Data Quality Objective (Dukelow et al. 1995) and Memorandum of Understanding for the Organic Complexant Safety Issue Data Requirements (Schreiber 1997a). Vapor screening issues apply as well, but are outside the scope of this SAP. A physical profile prediction based on waste fill history and previous sampling information is provided in Appendix A. Prior to core sampling, the dome space (below the riser) shall be measured for the presence of flammable gases. The measurement shall be taken from within the dome space and the data reported as a percentage of the lower flammability limit (LFL). The results shall be transmitted to the tank coordinator within ten working days of the sampling event (Schreiber 1997b). If the results are above 25 percent of the LFL when analyzing by gas chromatography/mass spectrometry or gas-specific monitoring gauges or above 10% of the LFL when analyzing with a combustible gas meter, the necessity for recurring sampling for flammable gas concentration and the frequency of such sampling will be determined by the Flammable Gas Safety Project. Any additional vapor sampling is not within the scope of this SAP

MR evaluation of femoral neck version and tibial torsion

Energy Technology Data Exchange (ETDEWEB)

Koenig, James Karl; Dwek, Jerry R. [University of California, San Diego, Children' s Hospital and Health Center, Department of Radiology, San Diego, CA (United States); Pring, Maya E. [Rady Children' s Hospital, Department of Pediatric Orthopedic Surgery, San Diego, CA (United States)

2012-01-15

Abnormalities of femoral neck version have been associated with a number of hip abnormalities in children, including slipped capital femoral epiphysis, proximal femoral focal deficiency, coxa vara, a deep acetabulum and, rarely, developmental dysplasia of the hip. Orthopedic surgeons also are interested in quantifying the femoral neck anteversion or retroversion in children especially to plan derotational osteotomies. Historically, the angle of femoral version and tibial torsion has been measured with the use of radiography and later by CT. Both methods carry with them the risks associated with ionizing radiation. Techniques that utilize MR are used less often because of the associated lengthy imaging times. This article describes a technique using MRI to determine femoral neck version and tibial torsion with total scan times of approximately 10 min. (orig.)

Yerington Paiute Tribe Energy Plan Version 1

Energy Technology Data Exchange (ETDEWEB)

Consulting, BB9 [BB9 Consulting; Director, Environmental

2014-04-01

The Yerington Paiute Tribe has made energy management and planning a priority. The Tribal Council has recognized that energy is an important component of their goal of self-sufficiency. Recognizing energy development as a component of the Tribe’s natural resources provides for needed economic development.A number of priorities have been identified for energy development. These range from immediate housing needs such as weatherization and solar to interest in energy as economic development.

Mission Planning and Decision Support for Underwater Glider Networks: A Sampling on-Demand Approach.

Science.gov (United States)

Ferri, Gabriele; Cococcioni, Marco; Alvarez, Alberto

2015-12-26

This paper describes an optimal sampling approach to support glider fleet operators and marine scientists during the complex task of planning the missions of fleets of underwater gliders. Optimal sampling, which has gained considerable attention in the last decade, consists in planning the paths of gliders to minimize a specific criterion pertinent to the phenomenon under investigation. Different criteria (e.g., A, G, or E optimality), used in geosciences to obtain an optimum design, lead to different sampling strategies. In particular, the A criterion produces paths for the gliders that minimize the overall level of uncertainty over the area of interest. However, there are commonly operative situations in which the marine scientists may prefer not to minimize the overall uncertainty of a certain area, but instead they may be interested in achieving an acceptable uncertainty sufficient for the scientific or operational needs of the mission. We propose and discuss here an approach named sampling on-demand that explicitly addresses this need. In our approach the user provides an objective map, setting both the amount and the geographic distribution of the uncertainty to be achieved after assimilating the information gathered by the fleet. A novel optimality criterion, called A η , is proposed and the resulting minimization problem is solved by using a Simulated Annealing based optimizer that takes into account the constraints imposed by the glider navigation features, the desired geometry of the paths and the problems of reachability caused by ocean currents. This planning strategy has been implemented in a Matlab toolbox called SoDDS (Sampling on-Demand and Decision Support). The tool is able to automatically download the ocean fields data from MyOcean repository and also provides graphical user interfaces to ease the input process of mission parameters and targets. The results obtained by running SoDDS on three different scenarios are provided and show that So

Mission Planning and Decision Support for Underwater Glider Networks: A Sampling on-Demand Approach

Directory of Open Access Journals (Sweden)

Gabriele Ferri

2015-12-01

Full Text Available This paper describes an optimal sampling approach to support glider fleet operators and marine scientists during the complex task of planning the missions of fleets of underwater gliders. Optimal sampling, which has gained considerable attention in the last decade, consists in planning the paths of gliders to minimize a specific criterion pertinent to the phenomenon under investigation. Different criteria (e.g., A, G, or E optimality, used in geosciences to obtain an optimum design, lead to different sampling strategies. In particular, the A criterion produces paths for the gliders that minimize the overall level of uncertainty over the area of interest. However, there are commonly operative situations in which the marine scientists may prefer not to minimize the overall uncertainty of a certain area, but instead they may be interested in achieving an acceptable uncertainty sufficient for the scientific or operational needs of the mission. We propose and discuss here an approach named sampling on-demand that explicitly addresses this need. In our approach the user provides an objective map, setting both the amount and the geographic distribution of the uncertainty to be achieved after assimilating the information gathered by the fleet. A novel optimality criterion, called A η , is proposed and the resulting minimization problem is solved by using a Simulated Annealing based optimizer that takes into account the constraints imposed by the glider navigation features, the desired geometry of the paths and the problems of reachability caused by ocean currents. This planning strategy has been implemented in a Matlab toolbox called SoDDS (Sampling on-Demand and Decision Support. The tool is able to automatically download the ocean fields data from MyOcean repository and also provides graphical user interfaces to ease the input process of mission parameters and targets. The results obtained by running SoDDS on three different scenarios are provided

Mission Planning and Decision Support for Underwater Glider Networks: A Sampling on-Demand Approach

Science.gov (United States)

Ferri, Gabriele; Cococcioni, Marco; Alvarez, Alberto

2015-01-01

This paper describes an optimal sampling approach to support glider fleet operators and marine scientists during the complex task of planning the missions of fleets of underwater gliders. Optimal sampling, which has gained considerable attention in the last decade, consists in planning the paths of gliders to minimize a specific criterion pertinent to the phenomenon under investigation. Different criteria (e.g., A, G, or E optimality), used in geosciences to obtain an optimum design, lead to different sampling strategies. In particular, the A criterion produces paths for the gliders that minimize the overall level of uncertainty over the area of interest. However, there are commonly operative situations in which the marine scientists may prefer not to minimize the overall uncertainty of a certain area, but instead they may be interested in achieving an acceptable uncertainty sufficient for the scientific or operational needs of the mission. We propose and discuss here an approach named sampling on-demand that explicitly addresses this need. In our approach the user provides an objective map, setting both the amount and the geographic distribution of the uncertainty to be achieved after assimilating the information gathered by the fleet. A novel optimality criterion, called Aη, is proposed and the resulting minimization problem is solved by using a Simulated Annealing based optimizer that takes into account the constraints imposed by the glider navigation features, the desired geometry of the paths and the problems of reachability caused by ocean currents. This planning strategy has been implemented in a Matlab toolbox called SoDDS (Sampling on-Demand and Decision Support). The tool is able to automatically download the ocean fields data from MyOcean repository and also provides graphical user interfaces to ease the input process of mission parameters and targets. The results obtained by running SoDDS on three different scenarios are provided and show that So

Sampling and Analysis Plan for N-Springs ERA pump-and-treat waste media

International Nuclear Information System (INIS)

Stankovich, M.T.

1996-07-01

This Sampling and Analysis Plan details the administrative procedures to be used to conduct sampling activities for characterization of spent ion-exchange resin, clinoptilolite, generated from the N-Springs pump-and-treat expedited response action. N-Springs (riverbank seeps) is located in the 100-N Area of the Hanford Site. Groundwater contained in the 100-NR-2 Operable Unit is contaminated with various radionuclides derived from wastewater disposal practices and spills associated with 100-N Reactor Operations

The Italian version of the Depression Anxiety Stress Scales-21: Factor structure and psychometric properties on community and clinical samples.

Science.gov (United States)

Bottesi, Gioia; Ghisi, Marta; Altoè, Gianmarco; Conforti, Erica; Melli, Gabriele; Sica, Claudio

2015-07-01

The Depression Anxiety Stress Scales-21 (DASS-21) is the short version of a self-report measure that was originally developed to provide maximum differentiation between depressive and anxious symptoms. Despite encouraging evidence, the factor structure and other features of the DASS-21 are yet to be firmly established. A community sample of 417 participants and two clinical groups (32 depressive patients and 25 anxious patients) completed the Italian version of the DASS-21 along with several measures of psychopathology. Confirmatory factor analyses suggested that the DASS-21 is a measure of general distress plus three additional orthogonal dimensions (anxiety, depression, and stress). The internal consistency and temporal stability of the measure were good; each DASS-21 scale correlated more strongly with a measure of a similar construct, demonstrating good convergent and divergent validity. Lastly, the DASS-21 demonstrated good criterion-oriented validity. The validity of the Italian DASS-21 and its utility, both for community and clinical individuals, are supported. Copyright © 2015 Elsevier Inc. All rights reserved.

Sampling and analysis plan (SAP) for WESF drains and TK-100 sump

International Nuclear Information System (INIS)

Simmons, F.M.

1998-01-01

The intent of this project is to determine whether the Waste Encapsulation and Storage Facility (WESF) floor drain piping and the TK-100 sump are free from contamination. TK-100 is currently used as a catch tank to transfer low level liquid waste from WESF to Tank Farms via B Plant. This system is being modified as part of the WESF decoupling since B Plant is being deactivated. As a result of the 1,1,1-trichloroethane (TCA) discovery in TK-100, the associated WESF floor drains and the pit sump need to be sampled. Breakdown constituents have been reviewed and found to be non-hazardous. There are 29 floor drains that tie into a common header leading into the tank. To prevent high exposure during sampling of the drains, TK-100 will be removed into the B Plant canyon and a new tank will be placed in the pit before any floor drain samples are taken. The sump will be sampled prior to TK-100 removal. A sample of the sludge and any liquid in the sump will be taken and analyzed for TCA and polychlorinated biphenyl (PCB). After the sump has been sampled, the vault floor will be flushed. The flush will be transferred from the sump into TK-100. TK-100 will be moved into B Plant. The vault will then be cleaned of debris and visually inspected. If there is no visual indication of TCA or PCB staining, the vault will be painted and a new tank installed. If there is an indication of TCA or PCB from laboratory analysis or staining, further negotiations will be required to determine a path forward. A total of 8 sets of three 40ml samples will be required for all of the floor drains and sump. The sump set will include one 125ml solid sample. The only analysis required will be for TCA in liquids. PCBs will be checked in sump solids only. The Sampling and Analysis Plan (SAP) is written to provide direction for the sampling and analytical activities of the 29 WESF floor drains and the TK-100 sump. The intent of this plan is to define the responsibilities of the various organizations

Infant behaviour questionnaire - revised version: a psychometric study in a Portuguese sample.

Science.gov (United States)

Costa, Raquel; Figueiredo, Bárbara

2018-04-01

Although the original characteristics of temperament tend to remain constant over the course of development, environmental circumstances may influence infants' reactions and behaviour. Parents' reports of infant temperament are rich informants of infant behaviours in different contexts. This study aimed to examine the psychometric properties of the Portuguese version of the Infant Behaviour Questionnaire - Revised (IBQ-R) and test the adequacy of the original and other previously published structures to the Portuguese data. 330 mothers and 81 fathers of children aged between 3 and 12 months completed the Portuguese version of the IBQ-R. The confirmatory factorial analysis revealed a non-adequate model fit of the IBQ-R original structure to the Portuguese data; nonetheless, it did reveal an adequate model fit of a previous published IBQ-R structure. This structure, although only slightly different from the original one, seems to be more suitable for the Portuguese data. This study provides data that indicates that the IBQ-R is a reliable questionnaire to evaluate infant temperament in the Portuguese culture.

Sampling and Analysis Plan for Tank 241-AP-108 Waste in Support of Evaporator Campaign 2000-1

International Nuclear Information System (INIS)

RASMUSSEN, J.H.

2000-01-01

This Tank Sampling and Analysis Plan (TSAP) identifies sample collection, laboratory analysis, quality assurance/quality control (QA/QC), and reporting objectives for the characterization of tank 241-AP-108 waste. Technical bases for these objectives are specified in the 242-A Evaporator Data Quality Objectives (Bowman 2000 and Von Bargen 1998) and 108-AP Tank Sampling Requirements in Support of Evaporator Campaign 2000-1 (Le 2000). Evaporator campaign 2000-1 will process waste from tank 241-AP-108 in addition to that from tank 241-AP-107. Characterization results will be used to support the evaporator campaign currently planned for early fiscal year 2000. No other needs (or issues) requiring data for this tank waste apply to this sampling event

The SPAI-18, a brief version of the social phobia and anxiety inventory: reliability and validity in clinically referred and non-referred samples.

Science.gov (United States)

de Vente, Wieke; Majdandžić, Mirjana; Voncken, Marisol J; Beidel, Deborah C; Bögels, Susan M

2014-03-01

We developed a new version of the Social Phobia and Anxiety Inventory (SPAI) in order to have a brief instrument for measuring social anxiety and social anxiety disorder (SAD) with a strong conceptual foundation. In the construction phase, a set of items representing 5 core aspects of social anxiety was selected by a panel of social anxiety experts. The selected item pool was validated using factor analysis, reliability analysis, and diagnostic analysis in a sample of healthy participants (N = 188) and a sample of clinically referred participants diagnosed with SAD (N = 98). This procedure resulted in an abbreviated version of the Social Phobia Subscale of the SPAI consisting of 18 items (i.e. the SPAI-18), which correlated strongly with the Social Phobia Subscale of the original SPAI (both groups r = .98). Internal consistency and diagnostic characteristics using a clinical cut-off score > 48 were good to excellent (Cronbach's alpha healthy group = .93; patient group = .91; sensitivity: .94; specificity: .88). The SPAI-18 was further validated in a community sample of parents-to-be without SAD (N = 237) and with SAD (N = 65). Internal consistency was again excellent (both groups Cronbach's alpha = .93) and a screening cut-off of > 36 proved to result in good sensitivity and specificity. The SPAI-18 also correlated strongly with other social anxiety instruments, supporting convergent validity. In sum, the SPAI-18 is a psychometrically sound instrument with good screening capacity for social anxiety disorder in clinical as well as community samples. Copyright © 2013 Elsevier Ltd. All rights reserved.

Sampling and analysis plan for assessment of beryllium in soils surrounding TA-40 building 15

Energy Technology Data Exchange (ETDEWEB)

Ruedig, Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-12-19

Technical Area (TA) 40 Building 15 (40-15) is an active firing site at Los Alamos National Laboratory. The weapons facility operations (WFO) group plans to build an enclosure over the site in 2017, so that test shots may be conducted year-round. The enclosure project is described in PRID 16P-0209. 40-15 is listed on LANL OSH-ISH’s beryllium inventory, which reflects the potential for beryllium in/on soils and building surfaces at 40-15. Some areas in and around 40-15 have previously been sampled for beryllium, but past sampling efforts did not achieve complete spatial coverage of the area. This Sampling and Analysis Plan (SAP) investigates the area surrounding 40-15 via 9 deep (≥1-ft.) soil samples and 11 shallow (6-in.) soil samples. These samples will fill the spatial data gaps for beryllium at 40-15, and will be used to support OSH-ISH’s final determination of 40-15’s beryllium registry status. This SAP has been prepared by the Environmental Health Physics program in consultation with the Industrial Hygiene program. Industrial Hygiene is the owner of LANL’s beryllium program, and will make a final determination with regard to the regulatory status of beryllium at 40-15.

Patient satisfaction with childbirth after external cephalic version.

Science.gov (United States)

Bogner, Gerhard; Hammer, Barbara Eva; Schausberger, Christiane; Fischer, Thorsten; Reisenberger, Klaus; Jacobs, Volker

2014-03-01

To assess acceptance and impact of external cephalic version (ECV) for breech presentation at term on maternal satisfaction with childbirth. Retrospective study on n = 131 women with breech presentation comparing maternal satisfaction after ECV and consecutive childbirth (n = 66; 50.4% of these successful attempts in n = 33; 50%) against the group without ECV and primary caesarean section (CS) (n = 65; 49.6%) instead using a questionnaire. Women with successful ECV tolerated side effects of the intervention better than after unsuccessful ECV (pain, tocolytics, mental and physical state, for all p version were more satisfied with childbirth than women with planned CS (p = 0.05). Women with version attempts tend to perceive childbirth as being less problematic with fewer complications (9.5 vs. 19%, p = 0.12). Unsuccessful ECVs had no negative impact on satisfaction with childbirth (p = 0.072). Attempting ECV seems to be an option for increasing the rate of vaginal births with breech presentation without negative impact on maternal satisfaction regarding consecutive childbirth.

Interventions to help external cephalic version for breech presentation at term.

Science.gov (United States)

Hofmeyr, G J

2004-01-01

Breech presentation places a fetus at increased risk. The outcome for the baby is improved by planned caesarean section compared with planned vaginal delivery. External cephalic version attempts to reduce the chances of breech presentation at birth, but is not always successful. Tocolytic drugs to relax the uterus as well as other methods have been used in an attempt to facilitate external cephalic version at term. To assess the effects of routine tocolysis, fetal acoustic stimulation, epidural or spinal analgesia and transabdominal amnioinfusion for external cephalic version at term on successful version and measures of pregnancy outcome. The Cochrane Pregnancy and Childbirth Group trials register (September 2003) and the Cochrane Central Register of Controlled Trials (The Cochrane Library, Issue 3, 2003) were searched. Randomised and quasi-randomised trials comparing routine versus selective or no tocolysis; fetal acoustic stimulation in midline fetal spine positions versus dummy or no stimulation; epidural or spinal analgesia versus no regional analgesia; or transabdominal amnioinfusion versus no amnioinfusion for external cephalic version at term. The reviewer assessed eligibility and trial quality. In six trials, routine tocolysis with beta-stimulants was associated with fewer failures of external cephalic version (relative risk (RR) 0.74, 95% confidence interval (CI) 0.64 to 0.87). The reduction in non-cephalic presentations at birth was not statistically significant. Caesarean sections were reduced (RR 0.85, 95% CI 0.72 to 0.99). In four small trials, sublingual nitroglycerine used as a tocolytic was associated with significant side-effects, and was not found to be effective. Fetal acoustic stimulation in midline fetal spine positions was associated with fewer failures of external cephalic version at term (RR 0.17, 95% CI 0.05 to 0.60). With epidural or spinal analgesia, external cephalic version failure, non-cephalic births and caesarean sections were

Sampling and Analysis Plan for Supplemental Environmental Project: Aquatic Life Surveys

Energy Technology Data Exchange (ETDEWEB)

Berryhill, Jesse Tobias [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gaukler, Shannon Marie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-09-26

As part of a settlement agreement for nuclear waste incidents in 2014, several supplemental environment projects (SEPs) were initiated at Los Alamos National Laboratory (LANL or the Laboratory) between the U.S. Department of Energy and the state of New Mexico. One SEP from this agreement consists of performing aquatic life surveys and will be used to assess the applicability of using generic ambient water-quality criteria (AWQC) for aquatic life. AWQC are generic criteria developed by the U.S. Environmental Protection Agency (EPA) to cover a broad range of aquatic species and are not unique to a specific region or state. AWQC are established by a composition of toxicity data, called species sensitivity distributions (SSDs), and are determined by LC50 (lethal concentration of 50% of the organisms studied) acute toxicity experiments for chemicals of interest. It is of interest to determine whether aquatic species inhabiting waters on the Pajarito Plateau are adequately protected using the current generic AWQC. The focus of this study will determine which aquatic species are present in ephemeral, intermittent, and perennial waters within LANL boundaries and from reference waters adjacent to LANL. If the species identified from these waters do not generally represent species used in the SSDs, then SSDs may need to be modified and AWQC may need to be updated. This sampling and analysis plan details the sampling methodology, surveillance locations, temporal scheduling, and analytical approaches that will be used to complete aquatic life surveys. A significant portion of this sampling and analysis plan was formalized by referring to Appendix E: SEP Aquatic Life Surveys DQO (Data Quality Objectives).

Development of a Chinese version of the Oswestry Disability Index version 2.1.

Science.gov (United States)

Lue, Yi-Jing; Hsieh, Ching-Lin; Huang, Mao-Hsiung; Lin, Gau-Tyan; Lu, Yen-Mou

2008-10-01

Cross-cultural adaptation and cross-sectional psychometric testing in a convenience sample of patients with low back pain. To translate and culturally adapt the Oswestry Disability Index version 2.1 (ODI 2.1) into a Mandarin Chinese version and to assess its reliability and validity. The Chinese ODI 2.1 has not been developed and validated. The ODI 2.1 was translated and culturally adapted to the Chinese version. The validity of the translated Chinese version was assessed by examining the relationship between the ODI and other well-known measures. Test-retest reliability was examined in 52 of these patients, who completed a second questionnaire within 1 week. Internal consistency of the ODI 2.1 was excellent with Cronbach's alpha = 0.903. The intraclass correlation coefficient of test-retest reliability was 0.89. The minimal detectable change was 12.8. The convergent validity of the Chinese ODI is supported by its high correlation with other physical functional status measures (Roland Morris Disability Questionnaire and SF-36 physical functioning subscale, r = 0.76 and -0.75, respectively), and moderate correlation with other measures (Visual Analogue Scale, r = 0.68) and certain SF-36 subscales (role-physical, bodily pain, and social functioning, r range: -0.49 to -0.57). As expected, the ODI was least correlated with nonfunctional measures (SF-36 mental subscale and role-emotional subscale, r = -0.25 and -0.33, respectively). The results of this study indicate that the Chinese version of the ODI 2.1 is a reliable and valid instrument for the measurement of functional status in patients with low back pain.

Elaboration of reduced versions of Measurement tools: A practical Perspective

Directory of Open Access Journals (Sweden)

Nekane Balluerka

2012-01-01

Full Text Available The aim of the present study is to show, from a practical perspective, the guidelines that may be followed to create a reduced version of a measurement tool. Therefore, it describes in detail the process of creating the reduced Basque version of the CDS scale (Children's Depression Scale; Lang and Tisher, 1978, which measures depression in children and adolescents. In a first study, the items that make up the reduced version of the CDS (CDS-R are selected from a set of analysis conducted on a sample of 886 children and adolescents who were administered the extensive version of the CDS adapted to the Basque language (Balluerka, Gorostiaga, and Haranburu, 2012. Subsequently, the CDS-R is validated on a sample of 2,165 participants. This second study examines the factorial structure, the internal consistency and the temporal stability of the instrument, as well as the relationship between its dimensions and gender, academic performance, emotional intelligence and attachment. Thus, evidence is obtained on the reliability and validity of the reduced version of the instrument, which guarantees suitable evaluation of the construct the instrument is intended to measure.

Adolescents' perceptions of parental behavior: psychometric properties of the short Egna Minnen Beträffande Uppfostran-Adolescent version (S-EMBU-A) in a clinical sample.

Science.gov (United States)

Penelo, Eva; Viladrich, Carme; Domènech, Josep M

2012-01-01

The aim of this study was to evaluate the psychometric properties of the Spanish version of the short Egna Minnen Beträffande Uppfostran-Adolescent version (S-EMBU-A) in a clinical context. The S-EMBU-A is a 22-item self-report questionnaire, based on the original 64-item EMBU-A, that assesses perceived parental rearing style in adolescents, comprising 3 subscales (Rejection, Emotional Warmth, and Overprotection). The questionnaire was administered to a clinical sample of 281 Spanish psychiatric outpatients aged 13 to 18 years. Confirmatory factor analysis was performed, analyzing the adolescents' reports about their parents' rearing style. Confirmatory factor analysis yielded an acceptable fit to data of the 3-factor model (comparative fit index = 0.90; root mean squared error of approximation = 0.054) and parameters were equivalent for the ratings assigned to fathers and mothers. Satisfactory internal consistency reliability was obtained for the 3 scales (Cronbach α ≥ .74). The influence of gender (of adolescents and parents) and age on scale scores was inappreciable. High scores for Rejection and low scores for Emotional Warmth were related to bad relationships with parents, absence of family support, presence of rejection, harsh discipline, and lack of parental supervision. The Spanish version of S-EMBU-A can be used with psychometric guarantees to identify rearing style in psychiatric outpatients, because evidence of quality in clinical setting matches that obtained in community samples. Copyright © 2012 Elsevier Inc. All rights reserved.

ANALYSING ACCEPTANCE SAMPLING PLANS BY MARKOV CHAINS

Directory of Open Access Journals (Sweden)

Mohammad Mirabi

2012-01-01

Full Text Available

ENGLISH ABSTRACT: In this research, a Markov analysis of acceptance sampling plans in a single stage and in two stages is proposed, based on the quality of the items inspected. In a stage of this policy, if the number of defective items in a sample of inspected items is more than the upper threshold, the batch is rejected. However, the batch is accepted if the number of defective items is less than the lower threshold. Nonetheless, when the number of defective items falls between the upper and lower thresholds, the decision-making process continues to inspect the items and collect further samples. The primary objective is to determine the optimal values of the upper and lower thresholds using a Markov process to minimise the total cost associated with a batch acceptance policy. A solution method is presented, along with a numerical demonstration of the application of the proposed methodology.

AFRIKAANSE OPSOMMING: In hierdie navorsing word ’n Markov-ontleding gedoen van aannamemonsternemingsplanne wat plaasvind in ’n enkele stap of in twee stappe na gelang van die kwaliteit van die items wat geïnspekteer word. Indien die eerste monster toon dat die aantal defektiewe items ’n boonste grens oorskry, word die lot afgekeur. Indien die eerste monster toon dat die aantal defektiewe items minder is as ’n onderste grens, word die lot aanvaar. Indien die eerste monster toon dat die aantal defektiewe items in die gebied tussen die boonste en onderste grense lê, word die besluitnemingsproses voortgesit en verdere monsters word geneem. Die primêre doel is om die optimale waardes van die booonste en onderste grense te bepaal deur gebruik te maak van ’n Markov-proses sodat die totale koste verbonde aan die proses geminimiseer kan word. ’n Oplossing word daarna voorgehou tesame met ’n numeriese voorbeeld van die toepassing van die voorgestelde oplossing.

Deferred Tax Assets and Deferred Tax Expense Against Tax Planning Profit Management

Directory of Open Access Journals (Sweden)

Warsono

2017-09-01

Full Text Available The purpose of this study is to examine the probability of earnings management performed by Property and Real Estate companies listed in Indonesia Stock Exchange (BEI in the period 2011-2015. How to do the management to influence the accounting numbers can be either profit management through deferred tax assets, deferred tax expense and tax planning in the financial statements. This paper examines the effect of deferred tax assets deferred tax burden, and tax planning to earnings management conducted by the company. Data of the research is to use secondary data from company financial statements that were downloaded from the official website of Indonesia Stock Exchange. Using sampling technique is performed by purposive sampling. The study population is the Property and Real Estate companies listed in Indonesia Stock Exchange in the period 2011-2015. The study take sample as many as 34 companies Property and Real Estate in the Stock Exchange in 2011-2015. Hypothesis testing uses multiple regressions with SPSS software version 22. The result shows that the Deferred Tax Assets positive and significant effect on earnings management; while deferred tax expense and tax planning significant negative effect on earnings management.

FIRM: Sampling-based feedback motion-planning under motion uncertainty and imperfect measurements

KAUST Repository

Agha-mohammadi, A.-a.; Chakravorty, S.; Amato, N. M.

2013-01-01

In this paper we present feedback-based information roadmap (FIRM), a multi-query approach for planning under uncertainty which is a belief-space variant of probabilistic roadmap methods. The crucial feature of FIRM is that the costs associated with the edges are independent of each other, and in this sense it is the first method that generates a graph in belief space that preserves the optimal substructure property. From a practical point of view, FIRM is a robust and reliable planning framework. It is robust since the solution is a feedback and there is no need for expensive replanning. It is reliable because accurate collision probabilities can be computed along the edges. In addition, FIRM is a scalable framework, where the complexity of planning with FIRM is a constant multiplier of the complexity of planning with PRM. In this paper, FIRM is introduced as an abstract framework. As a concrete instantiation of FIRM, we adopt stationary linear quadratic Gaussian (SLQG) controllers as belief stabilizers and introduce the so-called SLQG-FIRM. In SLQG-FIRM we focus on kinematic systems and then extend to dynamical systems by sampling in the equilibrium space. We investigate the performance of SLQG-FIRM in different scenarios. © The Author(s) 2013.

FIRM: Sampling-based feedback motion-planning under motion uncertainty and imperfect measurements

KAUST Repository

Agha-mohammadi, A.-a.

2013-11-15

In this paper we present feedback-based information roadmap (FIRM), a multi-query approach for planning under uncertainty which is a belief-space variant of probabilistic roadmap methods. The crucial feature of FIRM is that the costs associated with the edges are independent of each other, and in this sense it is the first method that generates a graph in belief space that preserves the optimal substructure property. From a practical point of view, FIRM is a robust and reliable planning framework. It is robust since the solution is a feedback and there is no need for expensive replanning. It is reliable because accurate collision probabilities can be computed along the edges. In addition, FIRM is a scalable framework, where the complexity of planning with FIRM is a constant multiplier of the complexity of planning with PRM. In this paper, FIRM is introduced as an abstract framework. As a concrete instantiation of FIRM, we adopt stationary linear quadratic Gaussian (SLQG) controllers as belief stabilizers and introduce the so-called SLQG-FIRM. In SLQG-FIRM we focus on kinematic systems and then extend to dynamical systems by sampling in the equilibrium space. We investigate the performance of SLQG-FIRM in different scenarios. © The Author(s) 2013.

Vietnamese validation of the short version of Internet Addiction Test

OpenAIRE

Tran, Bach Xuan; Mai, Hue Thi; Nguyen, Long Hoang; Nguyen, Cuong Tat; Latkin, Carl A.; Zhang, Melvyn W.B.; Ho, Roger C.M.

2017-01-01

Background and aims: The main goal of the present study was to examine the psychometric properties of a Vietnamese version of the short-version of Internet Addiction Test (s-IAT) and to assess the relationship between s-IAT scores and demographics, health related qualify of life and perceived stress scores in young Vietnamese. Methods: The Vietnamese version of s-IAT was administered to a sample of 589 participants. Exploratory factor and reliability analyses were performed. Regression analys...

Sampling and Analysis Plan for the 105-N Basin Water

International Nuclear Information System (INIS)

R.O. Mahood

1997-01-01

This sampling and analysis plan defines the strategy, and field and laboratory methods that will be used to characterize 105-N Basin water. The water will be shipped to the 200 Area Effluent Treatment Facility for treatment and disposal as part of N Reactor deactivation. These analyses are necessary to ensure that the water will meet the acceptance criteria of the ETF, as established in the Memorandum of Understanding for storage and treatment of water from N-Basin (Appendix A), and the characterization requirements for 100-N Area water provided in a letter from ETF personnel (Appendix B)

Validation of a Portuguese Version of the Children's Hope Scale

Science.gov (United States)

Marques, Susana C.; Pais-Ribeiro, J. L.; Lopez, Shane J.

2009-01-01

The article describes the development of the Portuguese version of the Children's Hope Scale and the examination of its psychometric properties. A sample of 367 Portuguese students completed the Portuguese-language versions of the Children's Hope Scale (CHS; Snyder et al., 1997), Students' Life Satisfaction Scale (SLSS; Huebner, 1991), Global…

Adherence to anti-Parkinson drug therapy in the "REASON" sample of Italian patients with Parkinson's disease: the linguistic validation of the Italian version of the "Morisky Medical Adherence Scale-8 items".

Science.gov (United States)

Fabbrini, G; Abbruzzese, G; Barone, P; Antonini, A; Tinazzi, M; Castegnaro, G; Rizzoli, S; Morisky, D E; Lessi, P; Ceravolo, R

2013-11-01

Information about patients' adherence to therapy represents a primary issue in Parkinson's disease (PD) management. To perform the linguistic validation of the Italian version of the self-rated 8-Item Morisky Medical Adherence Scale (MMAS-8) and to describe in a sample of Italian patients affected by PD the adherence to anti-Parkinson drug therapy and the association between adherence and some socio-demographic and clinical features. MMAS-8 was translated into Italian language by two independent Italian mother-tongue translators. The consensus version was then back-translated by an English mother-tongue translator. This translation process was followed by a consensus meeting between the authors of translation and investigators and then by two comprehension tests. The translated version of the MMAS-8 scale was then administered at the baseline visit of the "REASON" study (Italian Study on the Therapy Management in Parkinson's disease: Motor, Non-Motor, Adherence and Quality Of Life Factors) in a large sample of PD patients. The final version of the MMAS-8 was easily understood. Mean ± SD MMAS-8 score was 6.1 ± 1.2. There were no differences in adherence to therapy in relationship to disease severity, gender, educational level or decision to change therapy. The Italian version of MMAS-8, the key tool of the REASON study to assess the adherence to therapy, has shown to be understandable to patients with PD. Patients enrolled in the REASON study showed medium therapy adherence.

Use of a brief version of the self-compassion inventory with an international sample of people with HIV/AIDS

Science.gov (United States)

Brion, John M.; Leary, Mark; Wantland, Dean; Sullivan, K.; Nokes, Kathleen; Bain, Catherine A; Chaiphibalsarisdi, Puangtip; Chen, Wei-ti; Holzemer, William L.; Eller, Lucille Sanzero; Iipinge, Scholastika; Johnson, Mallory O.; Portillo, Carmen; Voss, Joachim; Tyer-Viola, Lynda; Corless, Inge B; Nicholas, Patrice K; Rose, Carol Dawson; Phillips, J. Craig; Sefcik, Elizabeth; Mendez, Marta Rivero; Kirksey, Kenn M.

2013-01-01

The objective of this study was to extend the psychometric evaluation of a brief version of the Self Compassion Scale (SCS). A secondary analysis of data from an international sample of 1,967 English-speaking persons living with HIV disease was used to examine the factor structure, and reliability of the 12-item Brief Version Self Compassion Inventory (BVSCI). A Maximum Likelihood factor analysis and Oblimin with Kaiser Normalization confirmed a two-factor solution, accounting for 42.58% of the variance. The BVSCI supported acceptable internal consistencies, with .714 for the total scale and .822 for Factor I and .774 for Factor II. Factor I (lower self compassion) demonstrated strongly positive correlations with measures of anxiety and depression while Factor II (high self compassion) was inversely correlated with the measures. No significant differences were found in the BVSCI scores for gender, age, or having children. Levels of self-compassion were significantly higher in persons with HIV disease and other physical and psychological health conditions. The scale shows promise for the assessment of self-compassion in persons with HIV without taxing participants, and may prove essential in investigating future research aimed at examining correlates of self-compassion, as well as providing data for tailoring self-compassion interventions for persons with HIV. PMID:23527887

Planning Considerations for a Mars Sample Receiving Facility: Summary and Interpretation of Three Design Studies

Science.gov (United States)

Beaty, David W.; Allen, Carlton C.; Bass, Deborah S.; Buxbaum, Karen L.; Campbell, James K.; Lindstrom, David J.; Miller, Sylvia L.; Papanastassiou, Dimitri A.

2009-10-01

It has been widely understood for many years that an essential component of a Mars Sample Return mission is a Sample Receiving Facility (SRF). The purpose of such a facility would be to take delivery of the flight hardware that lands on Earth, open the spacecraft and extract the sample container and samples, and conduct an agreed-upon test protocol, while ensuring strict containment and contamination control of the samples while in the SRF. Any samples that are found to be non-hazardous (or are rendered non-hazardous by sterilization) would then be transferred to long-term curation. Although the general concept of an SRF is relatively straightforward, there has been considerable discussion about implementation planning. The Mars Exploration Program carried out an analysis of the attributes of an SRF to establish its scope, including minimum size and functionality, budgetary requirements (capital cost, operating costs, cost profile), and development schedule. The approach was to arrange for three independent design studies, each led by an architectural design firm, and compare the results. While there were many design elements in common identified by each study team, there were significant differences in the way human operators were to interact with the systems. In aggregate, the design studies provided insight into the attributes of a future SRF and the complex factors to consider for future programmatic planning.

A model national emergency plan for radiological accidents; Plan modelo nacional de respuesta de emergencia para accidentes radiologicos

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

The IAEA has supported several projects for the development of a national response plan for radiological emergencies. As a result, the IAEA has developed a model National Emergency Response Plan for Radiological Accidents (RAD PLAN), particularly for countries that have no nuclear power plants. This plan can be adapted for use by countries interested in developing their own national radiological emergency response plan, and the IAEA will supply the latest version of the RAD PLAN on computer diskette upon request.

A Decision Support Tool for Planning the Sampling of Tank 19

International Nuclear Information System (INIS)

Edwards, T.B.

2002-01-01

The Statistical Consulting Section (SCS) of the Savannah River Technology Center (SRTC) was asked to develop a decision support system (DSS) to aid in the planning of the process to characterize the heel of Tank 19. This characterization is to be based on samples of the tank heel, and the DSS is to be used to help determine the number of samples that might be needed to provide a meaningful characterization based upon assumptions for relevant variations and volumes. The objective of this report is to describe the framework used to develop the DSS and to document its calculations. The DSS was developed as a Microsoft Excel spreadsheet. Detailed input and output for two test cases are provided in the appendix as part of the documentation of this spreadsheet

Validation of the French version of the yale food addiction scale: an examination of its factor structure, reliability, and construct validity in a nonclinical sample.

Science.gov (United States)

Brunault, Paul; Ballon, Nicolas; Gaillard, Philippe; Réveillère, Christian; Courtois, Robert

2014-05-01

The concept of food addiction has recently been proposed by applying the Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition, Text Revision, criteria for substance dependence to eating behaviour. Food addiction has received increased attention given that it may play a role in binge eating, eating disorders, and the recent increase in obesity prevalence. Currently, there is no psychometrically sound tool for assessing food addiction in French. Our study aimed to test the psychometric properties of a French version of the Yale Food Addiction Scale (YFAS) by establishing its factor structure and construct validity in a nonclinical population. A total of 553 participants were assessed for food addiction (French version of the YFAS) and binge eating behaviour (Bulimic Investigatory Test Edinburgh and Binge Eating Scale). We tested the scale's factor structure (factor analysis for dichotomous data based on tetrachoric correlation coefficients), internal consistency, and construct validity with measures of binge eating. Our results supported a 1-factor structure, which accounted for 54.1% of the variance. This tool had adequate reliability and high construct validity with measures of binge eating in this population, both in its diagnosis and symptom count version. A 2-factor structure explained an additional 9.1% of the variance, and could differentiate between patients with high, compared with low, levels of insight regarding addiction symptoms. In our study, we validated a psychometrically sound French version of the YFAS, both in its symptom count and diagnostic version. Future studies should validate this tool in clinical samples.

Migration check tool: automatic plan verification following treatment management systems upgrade and database migration.

Science.gov (United States)

Hadley, Scott W; White, Dale; Chen, Xiaoping; Moran, Jean M; Keranen, Wayne M

2013-11-04

Software upgrades of the treatment management system (TMS) sometimes require that all data be migrated from one version of the database to another. It is necessary to verify that the data are correctly migrated to assure patient safety. It is impossible to verify by hand the thousands of parameters that go into each patient's radiation therapy treatment plan. Repeating pretreatment QA is costly, time-consuming, and may be inadequate in detecting errors that are introduced during the migration. In this work we investigate the use of an automatic Plan Comparison Tool to verify that plan data have been correctly migrated to a new version of a TMS database from an older version. We developed software to query and compare treatment plans between different versions of the TMS. The same plan in the two TMS systems are translated into an XML schema. A plan comparison module takes the two XML schemas as input and reports any differences in parameters between the two versions of the same plan by applying a schema mapping. A console application is used to query the database to obtain a list of active or in-preparation plans to be tested. It then runs in batch mode to compare all the plans, and a report of success or failure of the comparison is saved for review. This software tool was used as part of software upgrade and database migration from Varian's Aria 8.9 to Aria 11 TMS. Parameters were compared for 358 treatment plans in 89 minutes. This direct comparison of all plan parameters in the migrated TMS against the previous TMS surpasses current QA methods that relied on repeating pretreatment QA measurements or labor-intensive and fallible hand comparisons.

Sampling and analysis plan for the 107-N Basin recirculation building liquid/sediment

International Nuclear Information System (INIS)

Thompson, W.S.

1997-02-01

This sampling and analysis plan (SAP) defines the strategy and the field and laboratory methods that will be used to characterize the liquids and sediment within the following four 100-N buildings/areas: 1310-N valve pit area inside the Radioactive Chemical Waste Treatment Pump House (silo); 1314-N Waste Pump (Overflow) Tank at the Liquid Waste Disposal Station; 105-N Lift Station pump well and valve pit areas inside the 105-N Reactor Building; and 107-N Basin Recirculation Building. This characterization activity is being performed in support of the work scope identified in the N Reactor Deactivation Program Plan and the sampling strategy in the DQO. The characterization data will be used for comparison to decontamination and decommissioning (D and D) endpoint acceptance criteria in preparation for turnover of the above-listed facilities to the D and D project. The data will also be used for waste acceptance criteria evaluation in the selection of the appropriate disposition option for liquid and sediment currently contained in the facilities

Quality control of brachytherapy system module Oncentra MasterPlan V3.3 planning; Control de calidad del modulo de braquiterapia del sistema de planificacion Oncentra MasterPlan V3.3

Energy Technology Data Exchange (ETDEWEB)

Monja Ray, P. de la; Torres Pozas, S.; Sanchez Carrascal, M.; Macias Verde, D.; Martin Oliva, R.

2011-07-01

We present the results of quality control carried out the planning system (SP) MasterPlan Oncentra Brachy, version 3.3 (Nucletron), on the occasion of its launch, following the recommendations proposed in the Protocol for quality control in planning systems therapy with ionizing radiation [SEFM, published by the Spanish Society of Medical Physics (SEFM) in 2005].

Results from CrIS/ATMS Obtained Using an "AIRS Version-6 Like" Retrieval Algorithm

Science.gov (United States)

Susskind, Joel; Kouvaris, Louis; Iredell, Lena; Blaisdell, John

2015-01-01

AIRS and CrIS Version-6.22 O3(p) and q(p) products are both superior to those of AIRS Version-6.Monthly mean August 2014 Version-6.22 AIRS and CrIS products agree reasonably well with OMPS, CERES, and witheach other. JPL plans to process AIRS and CrIS for many months and compare interannual differences. Updates to thecalibration of both CrIS and ATMS are still being finalized. We are also working with JPL to develop a joint AIRS/CrISlevel-1 to level-3 processing system using a still to be finalized Version-7 retrieval algorithm. The NASA Goddard DISCwill eventually use this system to reprocess all AIRS and recalibrated CrIS/ATMS. .

Seeps and springs sampling and analysis plan for the environmental monitoring plan for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

1994-08-01

This Sampling and Analysis Plan addresses the monitoring, sampling, and analysis activities that will be conducted at seeps and springs and at two french drain outlets in support of the Environmental Monitoring Plan for Waste Area Grouping (WAG) 6. WAG 6 is a shallow-land-burial disposal facility for low-level radioactive waste at Oak Ridge National Laboratory, a research facility owned by the US Department of Energy and operated by Martin Marietta Energy Systems, Inc. Initially, sampling will be conducted at as many as 15 locations within WAG 6 (as many as 13 seeps and 2 french drain outlets). After evaluating the results obtained and reviewing the observations made by field personnel during the first round of sampling, several seeps and springs will be chosen as permanent monitoring points, together with the two french drain outlets. Baseline sampling of these points will then be conducted quarterly for 1 year (i.e., four rounds of sampling after the initial round). The samples will be analyzed for various geochemical, organic, inorganic, and radiological parameters. Permanent sampling points having suitable flow rates and conditions may be outfitted with automatic flow-monitoring equipment. The results of the sampling and flow-monitoring efforts will help to quantify flux moving across the ungauged perimeter of the site and will help to identify changes in releases from the contaminant sources.

Seeps and springs sampling and analysis plan for the environmental monitoring plan for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1994-08-01

This Sampling and Analysis Plan addresses the monitoring, sampling, and analysis activities that will be conducted at seeps and springs and at two french drain outlets in support of the Environmental Monitoring Plan for Waste Area Grouping (WAG) 6. WAG 6 is a shallow-land-burial disposal facility for low-level radioactive waste at Oak Ridge National Laboratory, a research facility owned by the US Department of Energy and operated by Martin Marietta Energy Systems, Inc. Initially, sampling will be conducted at as many as 15 locations within WAG 6 (as many as 13 seeps and 2 french drain outlets). After evaluating the results obtained and reviewing the observations made by field personnel during the first round of sampling, several seeps and springs will be chosen as permanent monitoring points, together with the two french drain outlets. Baseline sampling of these points will then be conducted quarterly for 1 year (i.e., four rounds of sampling after the initial round). The samples will be analyzed for various geochemical, organic, inorganic, and radiological parameters. Permanent sampling points having suitable flow rates and conditions may be outfitted with automatic flow-monitoring equipment. The results of the sampling and flow-monitoring efforts will help to quantify flux moving across the ungauged perimeter of the site and will help to identify changes in releases from the contaminant sources

Groundwater Quality Sampling and Analysis Plan for Environmental Monitoring Waste Area Grouping 6 at Oak Ridge National Laboratory. Environmental Restoration Program

International Nuclear Information System (INIS)

1995-09-01

This Sampling and Analysis Plan addresses groundwater quality sampling and analysis activities that will be conducted in support of the Environmental Monitoring Plan for Waste Area Grouping (WAG) 6. WAG 6 is a shallow-burial land disposal facility for low-level radioactive waste at the Oak Ridge National Laboratory, a research facility owned by the US Department of Energy and managed by Martin Marietta Energy Systems, Inc. (Energy Systems). Groundwater sampling will be conducted by Energy Systems at 45 wells within WAG 6. The samples will be analyzed for various organic, inorganic, and radiological parameters. The information derived from the groundwater quality monitoring, sampling, and analysis will aid in evaluating relative risk associated with contaminants migrating off-WAG, and also will fulfill Resource Conservation and Recovery Act (RCRA) interim permit monitoring requirements. The sampling steps described in this plan are consistent with the steps that have previously been followed by Energy Systems when conducting RCRA sampling

Comprehensive work plan and health and safety plan for the 7500 Area Contamination Site sampling at Oak Ridge National Laboratory, Oak Ridge, Tennessee. Environmental Restoration Program

Energy Technology Data Exchange (ETDEWEB)

Burman, S.N.; Landguth, D.C.; Uziel, M.S.; Hatmaker, T.L.; Tiner, P.F.

1992-05-01

As part of the Environmental Restoration Program sponsored by the US Department of Energy`s Office of Environmental Restoration and Waste Management, this plan has been developed for the environmental sampling efforts at the 7500 Area Contamination Site, Oak Ridge National Laboratory (ORNL), Oak Ridge, Tennessee. This plan was developed by the Measurement Applications and Development Group (MAD) of the Health and Safety Research Division of ORNL and will be implemented by ORNL/MAD. Major components of the plan include (1) a quality assurance project plan that describes the scope and objectives of ORNL/MAD activities at the 7500 Area Contamination Site, assigns responsibilities, and provides emergency information for contingencies that may arise during field operations; (2) sampling and analysis sections; (3) a site-specific health and safety section that describes general site hazards, hazards associated with specific tasks, personnel protection requirements, and mandatory safety procedures; (4) procedures and requirements for equipment decontamination and responsibilities for generated wastes, waste management, and contamination control; and (5) a discussion of form completion and reporting required to document activities at the 7500 Area Contamination Site.

Addendum to the Phase 2 Sampling and Analysis Plan for the Clinch River Remedial Investigation

International Nuclear Information System (INIS)

1994-03-01

This document is an addendum to the Phase 2 Sampling and Analysis Plan for the Clinch River Remedial Investigation (DOE 1993). The Department of Energy--Oak Ridge Operations (DOE-ORO) is proposing this addendum to the US Envianmental Protection Agency, Region IV (EPA-IV), and the Tennessee Department of Environment and Conservation (TDEC) as a reduced sampling program on the Clinch River arm of Watts Bar Reservoir and on Poplar Creek. DOE-ORO is proposing to maximize the use of existing data and minimize the collection of new data for water, sediment, and biota during Phase 2 of the Clinch River Remedial Investigation. The existing data along with the additional data collected in Phase 2 would be used to perform a baseline risk assessment and make remedial decisions. DOE-ORO considers that the existing data, the additional data collected in Phase 2, and on-site remedial investigation data would be sufficient to understand the nature and extent of the contamination problem in the Clinch River, perform a baseline risk assessment,and make remedial decisions. This addendum is organized in three sections. The first section provides background information and describes a rationale for modifying the Phase 2 Sampling and Analysis Plan. Section 2 presents a summary of the existing data for the Clinch River arm of Watts Bar Reservoir and an evaluation of the sufficiency of this data for a baseline human health and ecological risk assessment. Section 3 describes the revised Phase 2 Sampling and Analysis Plan for surface water, sediment, and biota in the Clinch River OU and in the Poplar Creek OU

Health and safety plan for characterization sampling of ETR and MTR facilities

International Nuclear Information System (INIS)

Baxter, D.E.

1994-10-01

This health and safety plan establishes the procedures and requirements that will be used to minimize health and safety risks to persons performing Engineering Test Reactor and Materials Test Reactor characterization sampling activities, as required by the Occupational Safety and Health Administration standard, 29 CFR 1910.120. It contains information about the hazards involved in performing the tasks, and the specific actions and equipment that will be used to protect persons working at the site

Sampling and analysis plan for sludge located in fuel storage canisters of the 105-K West basin

International Nuclear Information System (INIS)

Baker, R.B.

1997-01-01

This Sampling and Analysis Plan (SAP) provides direction for the first sampling of sludge from the K West Basin spent fuel canisters. The specially developed sampling equipment removes representative samples of sludge while maintaining the radioactive sample underwater in the basin pool (equipment is described in WHC-SD-SNF-SDD-004). Included are the basic background logic for sample selection, the overall laboratory analyses required and the laboratory reporting required. These are based on requirements put forth in the data quality objectives (WHC-SD-SNF-DQO-012) established for this sampling and characterization activity

40 CFR Appendix X to Part 86 - Sampling Plans for Selective Enforcement Auditing of Heavy-Duty Engines and Light-Duty Trucks

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Sampling Plans for Selective Enforcement Auditing of Heavy-Duty Engines and Light-Duty Trucks X Appendix X to Part 86 Protection of... Plans for Selective Enforcement Auditing of Heavy-Duty Engines and Light-Duty Trucks Table 1—Sampling...

User's manual, version 1.00 for Monteburns, version 3.01

International Nuclear Information System (INIS)

Poston, D.I.; Trellue, H.R.

1998-06-01

Monteburns is a fully automated tool that links the Monte Carlo transport code MCNP with the radioactive decay and burnup code ORIGEN2. Monteburns produces a large number of criticality and burnup results based on various material feed/removal specifications, power(s), and time intervals. The program processes input from the user that specifies the system geometry, initial material compositions, feed/removal specifications, and other code-specific parameters. Various results from MCNP, ORIGEN2, and other calculations are then output successively as the code runs. The principle function of monteburns is to transfer one-group cross section and flux values from MCNP to ORIGEN2, and then transfer the resulting material compositions (after irradiation and/or decay) from ORIGEN2 back to MCNP in a repeated, cyclic fashion. The basic requirement of the code is that the user have a working MCNP input file and other input parameters; all interaction with ORIGEN2 and other calculations are performed by monteburns. This report serves as a user's manual for monteburns. It describes how the code functions, what input the user must provide, the calculations performed by the code, and it presents the format required for input files, as well as samples of these files. Monteburns is still in a developmental stage; thus, additions and/or changes may be made over time, and the user's manual will change as well. This is the first version of the user's manual (valid for monteburns version 3.01); users should contact the authors to inquire if a more recent version is available

Phase 1 Characterization sampling and analysis plan West Valley demonstration project.

Energy Technology Data Exchange (ETDEWEB)

Johnson, R. L. (Environmental Science Division)

2011-06-30

The Phase 1 Characterization Sampling and Analysis Plan (CSAP) provides details about environmental data collection that will be taking place to support Phase 1 decommissioning activities described in the Phase 1 Decommissioning Plan for the West Valley Demonstration Project, Revision 2 (Phase I DP; DOE 2009). The four primary purposes of CSAP data collection are: (1) pre-design data collection, (2) remedial support, (3) post-remediation status documentation, and (4) Phase 2 decision-making support. Data collection to support these four main objectives is organized into two distinct data collection efforts. The first is data collection that will take place prior to the initiation of significant Phase 1 decommissioning activities (e.g., the Waste Management Area [WMA] 1 and WMA 2 excavations). The second is data collection that will occur during and immediately after environmental remediation in support of remediation activities. Both data collection efforts have a set of well-defined objectives that encompass the data needs of the four main CSAP data collection purposes detailed in the CSAP. The main body of the CSAP describes the overall data collection strategies that will be used to satisfy data collection objectives. The details of pre-remediation data collection are organized by WMA. The CSAP contains an appendix for each WMA that describes the details of WMA-specific pre-remediation data collection activities. The CSAP is intended to expand upon the data collection requirements identified in the Phase 1 Decommissioning Plan. The CSAP is intended to tightly integrate with the Phase 1 Final Status Survey Plan (FSSP). Data collection described by the CSAP is consistent with the FSSP where appropriate and to the extent possible.

The Yoruba version of the Beck Hopelessness Scale: psychometric characteristics and correlates of hopelessness in a sample of Nigerian psychiatric outpatients.

Science.gov (United States)

Aloba, Olutayo; Akinsulore, Adesanmi; Mapayi, Boladale; Oloniniyi, Ibiduniyi; Mosaku, Kolawole; Alimi, Taiwo; Esan, Olufemi

2015-01-01

Previous studies from the developed western countries have repeatedly demonstrated that hopelessness positively correlates with an increased risk of suicide in the context of chronic mental disorders such as schizophrenia and affective disorders. Despite this persistently strong association, the construct of hopelessness in terms of its factorial structure and correlates has not been explored among Nigerian psychiatric outpatients. The aim of this present study is to examine the psychometric characteristics of the Yoruba language culturally adapted version of the Beck Hopelessness Scale in a cross-sectional sample of psychiatric outpatients in South-western Nigeria. The participants were 327 Nigerian adult outpatients receiving treatment for schizophrenia, bipolar and depressive disorders, consecutively recruited from the outpatient psychiatric clinics of a university teaching hospital in South-western Nigeria. The outpatients were recruited over a one year period. They completed the Yoruba translated version of the Beck Hopelessness Scale (BHS-Y), a sociodemographic and illness-related questionnaire, the Beck Depression Inventory-II (BDI-II). Their level of functioning was assessed with the Global Assessment of Functioning Scale (GAF), psychopathology was evaluated with the Positive and Negative Syndrome Scale (PANSS) and the level of disability measured with the World Health Organization Disability Assessment Schedule (WHODAS-II). Suicidality and confirmation of the diagnoses of schizophrenia, bipolar and depressive disorders were evaluated with the Mini International Neuropsychiatric Interview (MINI). The construct of hopelessness in terms of factorial structure, reliability, validity and correlates was explored. Exploratory Factor Analysis using Principal Component Analysis with Varimax rotation was used to examine the factorial structure of the BHS-Y. Internal consistency was examined with Cronbach's alpha, and the construct validity of the scale was assessed

Concept of Operations for the Next Generation Air Transportation System, Version 2.0

Science.gov (United States)

2007-06-13

instrument flight rules [ IFR ]), and communication with the ANSP via voice radio. In airspace where TBO is used (see Section 2.4), the minimum...GENERATION AIR TRANSPORTATION SYSTEM (NEXTGEN) JOINT PLANNING AND DEVELOPMENT OFFICE 2-32 VERSION 2.0 Transport category IFR -capable rotorcraft...disapproval, or a recommendation to amend the plan to include easements, noise mitigation, and disclosure requirements. The jurisdiction seeking to approve

Guideline for Sampling and Analysis of Tar and Particles in Biomass Producer Gases. Version 3.3

Energy Technology Data Exchange (ETDEWEB)

Neeft, J.P.A.; Knoef, H.A.M.; Zielke, U.; Sjoestroem, K.; Hasler, P.; Simell, P.A.; Dorrington, M.A.; Thomas, L.; Abatzoglou, N.; Deutch, S.; Greil, C.; Buffinga, G.J.; Brage, C.; Suomalainen, M.

2002-07-01

This Guideline provides a set of procedures for the measurement of organic contaminants and particles in producer gases from biomass gasifiers. The procedures are designed to cover different gasifier types (updraft or downdraft fixed bed or fluidised bed gasifiers), operating conditions (0 - 900C and 0.6-60 bars) and concentration ranges (1 mg/m{sub n}{sup 3} to 300 g/m{sub n}{sup 3}). The Guideline describes a modular sampling train, and a set of procedures, which include: planning and preparation of the sampling, sampling and post-sampling, analysis, calculations, error analysis and reporting. The modular sampling train consists of 4 modules. Module 1 is a preconditioning module for isokinetic sampling and gas cooling. Module 2 is a particle collection module including a heated filter. Module 3 is a tar collection module with a gas quench (optionally by circulating a liquid), impinger bottles and a backup adsorber. Module 4 is a volume-sampling module consisting of a pump, a rotameter, a gas flow meter and pressure and temperature indicators. The equipment and materials that are required for procuring this modular sampling train are given in the Guideline. The sampling procedures consist of a description for isokinetic sampling, a leakage test prior to sampling, the actual sampling and its duration, how the equipment is cleaned after the sampling, and how the samples are prepared and stored. Analysis of the samples is performed via three procedures. Prior to these procedures, the sample is prepared by Soxhlet extraction of the tars on the particle filter and by collection of all tars in one bulk solution. The first procedure describes the weighing of the particle filter to obtain the concentration of particles in the biomass producer gas. The bulk tar solution is used for two purposes: for determination of gravimetric tar and for analysis of individual compounds. The second procedure describes how to determine the gravimetric tar mass from the bulk solution. The

Sampling and analysis plan for the Bear Creek Valley Boneyard/Burnyard Accelerated Action Project, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1998-03-01

In the Bear Creek Valley Watershed Remedial Investigation, the Boneyard/Burnyard was identified as the source of the largest releases of uranium into groundwater and surface water in Bear Creek Valley. The proposed action for remediation of this site is selective excavation and removal of source material and capping of the remainder of the site. The schedule for this action has been accelerated so that this is the first remedial action planned to be implemented in the Bear Creek Valley Record of Decision. Additional data needs to support design of the remedial action were identified at a data quality objectives meeting held for this project. Sampling at the Boneyard/Burnyard will be conducted through the use of a phased approach. Initial or primary samples will be used to make in-the-field decisions about where to locate follow-up or secondary samples. On the basis of the results of surface water, soil, and groundwater analysis, up to six test pits will be dug. The test pits will be used to provide detailed descriptions of source materials and bulk samples. This document sets forth the requirements and procedures to protect the personnel involved in this project. This document also contains the health and safety plan, quality assurance project plan, waste management plan, data management plan, implementation plan, and best management practices plan for this project as appendices

Sampling and analysis plan for the Bear Creek Valley Boneyard/Burnyard Accelerated Action Project, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In the Bear Creek Valley Watershed Remedial Investigation, the Boneyard/Burnyard was identified as the source of the largest releases of uranium into groundwater and surface water in Bear Creek Valley. The proposed action for remediation of this site is selective excavation and removal of source material and capping of the remainder of the site. The schedule for this action has been accelerated so that this is the first remedial action planned to be implemented in the Bear Creek Valley Record of Decision. Additional data needs to support design of the remedial action were identified at a data quality objectives meeting held for this project. Sampling at the Boneyard/Burnyard will be conducted through the use of a phased approach. Initial or primary samples will be used to make in-the-field decisions about where to locate follow-up or secondary samples. On the basis of the results of surface water, soil, and groundwater analysis, up to six test pits will be dug. The test pits will be used to provide detailed descriptions of source materials and bulk samples. This document sets forth the requirements and procedures to protect the personnel involved in this project. This document also contains the health and safety plan, quality assurance project plan, waste management plan, data management plan, implementation plan, and best management practices plan for this project as appendices.

AIRSAR South American deployment: Operation plan, version 3.0

Science.gov (United States)

Kobrick, M.

1993-01-01

The United States National Aeronautics and Space Administration (NASA) and the Brazilian Commission for Space Activities (COBAE) are undertaking a joint experiment involving NASA's DC-8 research aircraft and the Airborne Synthetic Aperture Radar (AIRSAR) system during late May and June 1993. The research areas motivating these activities are: (1) fundamental research in the role of soils, vegetation, and hydrology in the global carbon cycle; and (2) in cooperation with South American scientists, airborne remote sensing research for the upcoming NASA Spaceborne Imaging Radar (SIR)-C/X-SAR flights on the Space Shuttle. A flight schedule and plans for the deployment that were developed are included. Maps of the site locations and schematic indications of flight routes and dates, plots showing swath locations derived from the flight requests and generated by flight planning software, and, most importantly, a calendar showing which sites will be imaged each day are included.

Orthorexia nervosa behavior in a sample of Brazilian dietitians assessed by the Portuguese version of ORTO-15.

Science.gov (United States)

Alvarenga, M S; Martins, M C T; Sato, K S C J; Vargas, S V A; Philippi, S T; Scagliusi, F B

2012-03-01

Orthorexia nervosa (ON) is described as an obsessive pathological behavior characterized by a strong preoccupation with healthy eating and the avoidance of foods or ingredients considered unhealthy by the subject. Although it is still not officially recognized as an eating disorder, previous studies have discussed its frequency in some groups and a fifteen-question test (ORTO-15) was developed elsewhere to assess ON behavior. The present study aimed to evaluate ON behavior in a sample of Brazilian dietitians after testing the psychometric properties of the Portuguese version of ORTO-15. A total of 392 dietitians answered an online version of the test. The answers were analyzed regarding ON tendency, according with the scoring grid proposed by its authors. Exploratory factor analysis was performed and internal consistency was assessed. It was found that three questions of the test presented loadings lower than 0.5. The 12 remaining question formed 3 factors with internal consistency of -0.51, 0.63 and 0.47. The answers of the participants to these questions revealed a tendency to orthorexic behavior, mainly regarding aspects such as: making food choices conditioned by worry about health status, evaluating food rather from nutritional quality than from its taste, believing that consuming healthy food may improve appearance, discrediting the influence of mood on eating behavior and banning food choices considered by them as eating transgressions. There is no evidence of the validity and reliability of the ORTO-15 with the initial psychometric evaluation performed. Further analyses are needed. Nevertheless, it was possible to observe a high frequency of orthorexic behavior among the studied Brazilian dietitians. However, additional studies are needed to completely understand dietitians behavior toward ON.

Groundwater quality sampling and analysis plan for environmental monitoring in Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

1994-03-01

This Sampling and Analysis Plan addresses groundwater quality sampling and analysis activities that will be conducted in support of the Environmental Monitoring Plan for Waste Area Grouping (WAG) 6. WAG 6 is a shallow-burial land disposal facility for low-level radioactive waste at the Oak Ridge National Laboratory, a research facility owned by the US Department of energy and managed by martin Marietta Energy Systems, Inc. (Energy Systems). Groundwater sampling will be conducted by Energy Systems at 45 wells within WAG 6. The samples will be analyzed for various organic, inorganic, and radiological parameters. The information derived from the groundwater quality monitoring, sampling, and analysis will aid in evaluating relative risk associated with contaminants migrating off-WAG, and also will fulfill Resource Conservation and Recovery Act (RCRA) interim permit monitoring requirements. The sampling steps described in this plan are consistent with the steps that have previously been followed by Energy Systems when conducting RCRA sampling.

Groundwater quality sampling and analysis plan for environmental monitoring in Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1994-03-01

This Sampling and Analysis Plan addresses groundwater quality sampling and analysis activities that will be conducted in support of the Environmental Monitoring Plan for Waste Area Grouping (WAG) 6. WAG 6 is a shallow-burial land disposal facility for low-level radioactive waste at the Oak Ridge National Laboratory, a research facility owned by the US Department of energy and managed by martin Marietta Energy Systems, Inc. (Energy Systems). Groundwater sampling will be conducted by Energy Systems at 45 wells within WAG 6. The samples will be analyzed for various organic, inorganic, and radiological parameters. The information derived from the groundwater quality monitoring, sampling, and analysis will aid in evaluating relative risk associated with contaminants migrating off-WAG, and also will fulfill Resource Conservation and Recovery Act (RCRA) interim permit monitoring requirements. The sampling steps described in this plan are consistent with the steps that have previously been followed by Energy Systems when conducting RCRA sampling

Field Sampling Plan for the HWMA/RCRA Closure Certification of the TRA-731 Caustic and Acid Storage Tank System - 1997 Notice of Violation Consent Order

International Nuclear Information System (INIS)

Evans, S.K.

2002-01-01

This Field Sampling Plan for the HWMA/RCRA Closure Certification of the TRA-731 Caustic and Acid Storage Tank System is one of two documents that comprise the Sampling and Analysis Plan for the HWMA/RCRA closure certification of the TRA-731 caustic and acid storage tank system at the Idaho National Engineering and Environmental Laboratory. This plan, which provides information about sampling design, required analyses, and sample collection and handling procedures, is to be used in conjunction with the Quality Assurance Project Plan for the HWMA/RCRA Closure Certification of the TRA-731 Caustic and Acid Storage Tank System

A novel derivation of a within-batch sampling plan based on a Poisson-gamma model characterising low microbial counts in foods.

Science.gov (United States)

Gonzales-Barron, Ursula; Zwietering, Marcel H; Butler, Francis

2013-02-01

This study proposes a novel step-wise methodology for the derivation of a sampling plan by variables for food production systems characterised by relatively low concentrations of the inspected microorganism. After representing the universe of contaminated batches by modelling the between-batch and within-batch variability in microbial counts, a tolerance criterion defining batch acceptability (i.e., up to a tolerance percentage of the food units having microbial concentrations lower or equal to a critical concentration) is established to delineate a limiting quality contour that separates satisfactory from unsatisfactory batches. The problem consists then of finding the optimum decision criterion - arithmetic mean of the analytical results (microbiological limit, m(L)) and the sample size (n) - that satisfies a pre-defined level of confidence measured on the samples' mean distributions from all possible true within-batch distributions. This is approached by obtaining decision landscape curves representing collectively the conditional and joint producer's and consumer's risks at different microbiological limits along with confidence intervals representing uncertainty due to the propagated between-batch variability. Whilst the method requires a number of risk management decisions to be made such as the objective of the sampling plan (GMP-based or risk-based), the modality of derivation, the tolerance criterion or level of safety, and the statistical level of confidence, the proposed method can be used when past monitoring data are available so as to produce statistically-sound dynamic sampling plans with optimised efficiency and discriminatory power. For the illustration of Enterobacteriaceae concentrations on Irish sheep carcasses, a sampling regime of n=10 and m(L)=17.5CFU/cm(2) is recommended to ensure that the producer has at least a 90% confidence of accepting a satisfactory batch whilst the consumer at least a 97.5% confidence that a batch will not be

Using the Violence Risk Scale-Sexual Offense version in sexual violence risk assessments: Updated risk categories and recidivism estimates from a multisite sample of treated sexual offenders.

Science.gov (United States)

Olver, Mark E; Mundt, James C; Thornton, David; Beggs Christofferson, Sarah M; Kingston, Drew A; Sowden, Justina N; Nicholaichuk, Terry P; Gordon, Audrey; Wong, Stephen C P

2018-04-30

The present study sought to develop updated risk categories and recidivism estimates for the Violence Risk Scale-Sexual Offense version (VRS-SO; Wong, Olver, Nicholaichuk, & Gordon, 2003-2017), a sexual offender risk assessment and treatment planning tool. The overarching purpose was to increase the clarity and accuracy of communicating risk assessment information that includes a systematic incorporation of new information (i.e., change) to modify risk estimates. Four treated samples of sexual offenders with VRS-SO pretreatment, posttreatment, and Static-99R ratings were combined with a minimum follow-up period of 10-years postrelease (N = 913). Logistic regression was used to model 5- and 10-year sexual and violent (including sexual) recidivism estimates across 6 different regression models employing specific risk and change score information from the VRS-SO and/or Static-99R. A rationale is presented for clinical applications of select models and the necessity of controlling for baseline risk when utilizing change information across repeated assessments. Information concerning relative risk (percentiles) and absolute risk (recidivism estimates) is integrated with common risk assessment language guidelines to generate new risk categories for the VRS-SO. Guidelines for model selection and forensic clinical application of the risk estimates are discussed. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

A Fixed-Precision Sequential Sampling Plan for the Potato Tuberworm Moth, Phthorimaea operculella Zeller (Lepidoptera: Gelechidae), on Potato Cultivars.

Science.gov (United States)

Shahbi, M; Rajabpour, A

2017-08-01

Phthorimaea operculella Zeller is an important pest of potato in Iran. Spatial distribution and fixed-precision sequential sampling for population estimation of the pest on two potato cultivars, Arinda ® and Sante ® , were studied in two separate potato fields during two growing seasons (2013-2014 and 2014-2015). Spatial distribution was investigated by Taylor's power law and Iwao's patchiness. Results showed that the spatial distribution of eggs and larvae was random. In contrast to Iwao's patchiness, Taylor's power law provided a highly significant relationship between variance and mean density. Therefore, fixed-precision sequential sampling plan was developed by Green's model at two precision levels of 0.25 and 0.1. The optimum sample size on Arinda ® and Sante ® cultivars at precision level of 0.25 ranged from 151 to 813 and 149 to 802 leaves, respectively. At 0.1 precision level, the sample sizes varied from 5083 to 1054 and 5100 to 1050 leaves for Arinda ® and Sante ® cultivars, respectively. Therefore, the optimum sample sizes for the cultivars, with different resistance levels, were not significantly different. According to the calculated stop lines, the sampling must be continued until cumulative number of eggs + larvae reached to 15-16 or 96-101 individuals at precision levels of 0.25 or 0.1, respectively. The performance of the sampling plan was validated by resampling analysis using resampling for validation of sampling plans software. The sampling plant provided in this study can be used to obtain a rapid estimate of the pest density with minimal effort.

40 CFR Appendix A to Subpart G of... - Sampling Plans for Selective Enforcement Auditing of Marine Engines

Science.gov (United States)

2010-07-01

... Enforcement Auditing of Marine Engines A Appendix A to Subpart G of Part 91 Protection of Environment...-IGNITION ENGINES Selective Enforcement Auditing Regulations Pt. 91, Subpt. G, App. A Appendix A to Subpart G of Part 91—Sampling Plans for Selective Enforcement Auditing of Marine Engines Table 1—Sampling...

NETS - A NEURAL NETWORK DEVELOPMENT TOOL, VERSION 3.0 (MACINTOSH VERSION)

Science.gov (United States)

Phillips, T. A.

1994-01-01

allows the user to generate C code to implement the network loaded into the system. This permits the placement of networks as components, or subroutines, in other systems. In short, once a network performs satisfactorily, the Generate C Code option provides the means for creating a program separate from NETS to run the network. Other features: files may be stored in binary or ASCII format; multiple input propagation is permitted; bias values may be included; capability to scale data without writing scaling code; quick interactive testing of network from the main menu; and several options that allow the user to manipulate learning efficiency. NETS is written in ANSI standard C language to be machine independent. The Macintosh version (MSC-22108) includes code for both a graphical user interface version and a command line interface version. The machine independent version (MSC-21588) only includes code for the command line interface version of NETS 3.0. The Macintosh version requires a Macintosh II series computer and has been successfully implemented under System 7. Four executables are included on these diskettes, two for floating point operations and two for integer arithmetic. It requires Think C 5.0 to compile. A minimum of 1Mb of RAM is required for execution. Sample input files and executables for both the command line version and the Macintosh user interface version are provided on the distribution medium. The Macintosh version is available on a set of three 3.5 inch 800K Macintosh format diskettes. The machine independent version has been successfully implemented on an IBM PC series compatible running MS-DOS, a DEC VAX running VMS, a SunIPC running SunOS, and a CRAY Y-MP running UNICOS. Two executables for the IBM PC version are included on the MS-DOS distribution media, one compiled for floating point operations and one for integer arithmetic. The machine independent version is available on a set of three 5.25 inch 360K MS-DOS format diskettes (standard

The Psychometric Properties of Turkish Version of Depression Anxiety Stress Scale-21 (DASS-21 in Community and Clinical Samples

Directory of Open Access Journals (Sweden)

Hakan SARICAM

2018-04-01

Full Text Available This paper presented the Turkish version of the Depression Anxiety Stress Scale-21 (DASS-21 in community and clinical samples, examined its psychometric properties. Construct validity and concurrent validity were conducted in validity studies. Depression Anxiety Stress Scale-42 (DASS-42 was used for concurrent validity. In reliability analysis, the instrument’s internal consistency and re-test reliability were studied. Results of explanatory factor analyses demonstrated that 21 items yielded three-factors. Results of confirmatory factor analyses for three-dimensional model showed that acceptable fit index values in community sample and perfect fit index values in clinical sample. Factor loadings ranged from .42 to .72. In the concurrent validity, significant positive relationships were found between DASS-42 and DASS-21. Cronbach alpha internal consistency coefficient was found as α= .87 for depression sub-scale, α= .85 for anxiety sub-scale and α= .81 for stress sub-scale in clinical sample. Moreover, test-retest reliability coefficient was obtained as r=.68 for depression sub-scale, r=.66 for anxiety sub-scale and r=.61 for stress sub-scale in community sample, and corrected item-total correlations ranged from .43 to .77 in clinical sample. In second study, DASS-21 discriminated the patients (depression mean score=10.83; anxiety mean score=10.39; stress mean score=11.85 from the healthy subjects (depression mean score=5.88; anxiety mean score=5.37; stress mean score=7.90 well (U=5310.50; 4748.50; 5562.50, p=0.00. According to psychometric properties, DASS-21 is a reliable and valid instrument in the assessment of depression, anxiety, stress levels. [JCBPR 2018; 7(1.000: 19-30

UMTRA project water sampling and analysis plan, Mexican Hat, Utah

International Nuclear Information System (INIS)

1994-04-01

The Mexican Hat, Utah, Uranium Mill Tailings Remedial Action (UMTRA) Project site is a former uranium mill that is undergoing surface remediation in the form of on-site tailings stabilization. Contaminated surface materials from the Monument Valley, Arizona, UMTRA Project site have been transported to the Mexican Hat site and are being consolidated with the Mexican Hat tailings. The scheduled completion of the tailings disposal cell is August 1995. Water is found in two geologic units at the site: the Halgaito Shale Formation and the Honaker Trail Formation. The tailings rest on the Halgaito Shale, and water contained in that unit is a result of milling activities and, to a lesser extent, water released from the tailings from compaction during remedial action construction of the disposal cell. Water in the Halgaito Shale flows through fractures and discharges at seeps along nearby arroyos. Flow from the seeps will diminish as water drains from the unit. Ground water in the lower unit, the Honaker Trail Formation, is protected from contamination by an upward hydraulic gradient. There are no nearby water supply wells because of widespread poor background ground water quality and quantity, and the San Juan River shows no impacts from the site. This water sampling and analysis plan (WSAP) recommends sampling six seeps and one upgradient monitor well compared in the Honaker Trail Formation. Samples will be taken in April 1994 (representative of high group water levels) and September 1994 (representative of low ground water levels). Analyses will be performed on filtered samples for plume indicator parameters

Validation of the French Version of the DSM-5 Yale Food Addiction Scale in a Nonclinical Sample.

Science.gov (United States)

Brunault, Paul; Courtois, Robert; Gearhardt, Ashley N; Gaillard, Philippe; Journiac, Kevin; Cathelain, Sarah; Réveillère, Christian; Ballon, Nicolas

2017-03-01

The Yale Food Addiction Scale (YFAS) is the only questionnaire that assesses food addiction (FA) based on substance dependence criteria in the Diagnostic and Statistical Manual of Mental Disorders (DSM), Fourth Edition, Text Revision. Following recent updating of addiction criteria, a new DSM-5 version (YFAS 2.0) has been developed. Our study tested the psychometric properties of the French YFAS 2.0 in a nonclinical population. We assessed 330 nonclinical participants for FA (French YFAS 2.0), eating behaviour, and eating disorder (Binge Eating Scale, Emotional Overeating Questionnaire, Three-Factor Eating Questionnaire-R18, Questionnaire on Eating and Weight Patterns-Revised, Eating Disorder Diagnostic Scale). We tested the scale's factor structure (confirmatory factor analysis based on 11 diagnostic criteria), internal consistency, and construct and incremental validity. Prevalence of FA was 8.2%. Our results supported a 1-factor structure similar to the US version. In both its diagnostic and symptom count versions, the YFAS 2.0 had good internal consistency (Kuder-Richardson alpha was 0.83) and was associated with body mass index (BMI), binge eating, uncontrolled and emotional eating, binge eating disorder, and cognitive restraint. FA predicted BMI above and beyond binge eating frequency. Females had a higher prevalence of FA than males but not more FA symptoms. We validated a psychometrically sound French version of the YFAS 2.0 in a nonclinical population, in both its symptom count and diagnostic versions. Future studies should investigate psychometric properties of this questionnaire in clinical populations potentially at risk for FA (that is, patients with obesity, diabetes, hypertension, or other metabolic syndrome risk factors).

A model national emergency plan for radiological accidents

International Nuclear Information System (INIS)

2000-07-01

The IAEA has supported several projects for the development of a national response plan for radiological emergencies. As a result, the IAEA has developed a model National Emergency Response Plan for Radiological Accidents (RAD PLAN), particularly for countries that have no nuclear power plants. This plan can be adapted for use by countries interested in developing their own national radiological emergency response plan, and the IAEA will supply the latest version of the RAD PLAN on computer diskette upon request

Sample size planning for composite reliability coefficients: accuracy in parameter estimation via narrow confidence intervals.

Science.gov (United States)

Terry, Leann; Kelley, Ken

2012-11-01

Composite measures play an important role in psychology and related disciplines. Composite measures almost always have error. Correspondingly, it is important to understand the reliability of the scores from any particular composite measure. However, the point estimates of the reliability of composite measures are fallible and thus all such point estimates should be accompanied by a confidence interval. When confidence intervals are wide, there is much uncertainty in the population value of the reliability coefficient. Given the importance of reporting confidence intervals for estimates of reliability, coupled with the undesirability of wide confidence intervals, we develop methods that allow researchers to plan sample size in order to obtain narrow confidence intervals for population reliability coefficients. We first discuss composite reliability coefficients and then provide a discussion on confidence interval formation for the corresponding population value. Using the accuracy in parameter estimation approach, we develop two methods to obtain accurate estimates of reliability by planning sample size. The first method provides a way to plan sample size so that the expected confidence interval width for the population reliability coefficient is sufficiently narrow. The second method ensures that the confidence interval width will be sufficiently narrow with some desired degree of assurance (e.g., 99% assurance that the 95% confidence interval for the population reliability coefficient will be less than W units wide). The effectiveness of our methods was verified with Monte Carlo simulation studies. We demonstrate how to easily implement the methods with easy-to-use and freely available software. ©2011 The British Psychological Society.

Sampling and analysis plan for remediation of Operable Unit 100-IU-3 waste site 600-104

International Nuclear Information System (INIS)

1997-08-01

This sampling and analysis plan (SAP) presents the rationale and strategy for the sampling and analysis activities to support remediation of 100-IU-3 Operable Unit waste site 600-104. The purpose of the proposed sampling and analysis activities is to demonstrate that time-critical remediation of the waste site for soil containing 2,4-Dichlorophonoxyacetic acid salts and esters (2,4-D) and dioxin/furan isomers at concentrations that exceed cleanup levels has been effective. This shall be accomplished by sampling various locations of the waste site before and after remediation, analyzing the samples, and comparing the results to action levels set by the Washington State Department of Ecology

Validity and reliability of the Brazilian version of Yale-Brown obsessive compulsive scale-shopping version (YBOCS-SV).

Science.gov (United States)

Leite, Priscilla Lourenço; Filomensky, Tatiana Zambrano; Black, Donald W; Silva, Adriana Cardoso

2014-08-01

The Yale-Brown Obsessive Compulsive Scale-Shopping Version (YBOCS-SV) is considered the gold standard in the assessment of shopping severity. It is designed to assess cognitions and behaviors relating to compulsive buying behavior. The present study aims to assess the validity of the Brazilian version of this scale. For the study, composed the sample 610 participants: 588 subjects of a general population and 22 compulsive buyers. Factorial analysis was performed to assess the relations and the correlation between the YBOCS-SV, the Compulsive Buying Scale (CBS), and Richmond Compulsive Buying Scale (RCBS), was assessed using Pearson coefficient, for study of convergent and divergent validity. Cronbach's alpha coefficients were used to assess internal consistency. The results show good to excellent psychometric parameters for the YBOCS-SV in its Brazilian version. With regard to correlations, the YBOCS-SV is inversely and proportionally correlated with CBS and the RCBS, indicating that the YBOCS-SV is an excellent instrument for screening compulsive buying. The YBOCS-SV presented high alpha coefficient of Cronbach's alpha (0.92), demonstrating good reliability. The Brazilian version of the YBOCS-SV is indicated to diagnose compulsive buying disorder, and likely use for the purposes intended in the Brazilian population. Copyright © 2014 Elsevier Inc. All rights reserved.

40 CFR Appendix A to Subpart F of... - Sampling Plans for Selective Enforcement Auditing of Nonroad Engines

Science.gov (United States)

2010-07-01

... Enforcement Auditing of Nonroad Engines A Appendix A to Subpart F of Part 89 Protection of Environment... NONROAD COMPRESSION-IGNITION ENGINES Selective Enforcement Auditing Pt. 89, Subpt. F, App. A Appendix A to Subpart F of Part 89—Sampling Plans for Selective Enforcement Auditing of Nonroad Engines Table 1—Sampling...

School version of ESTE EU

International Nuclear Information System (INIS)

Carny, P.; Suchon, D.; Chyly, M.; Smejkalova, E.; Fabova, V.

2008-01-01

ESTE EU is information system and software for radiological impacts assessment to the territory of the country in case of radiation accident inside/outside of the country .The program enables to model dispersion of radioactive clouds in small-scale and meso-scale. The system enables the user to estimate prediction of the source term (release to the atmosphere ) for any point of radiation/nuclear accident in Europe (for any point of the release, but especially for the sites of European power reactors ). The system enables to utilize results of real radiological monitoring in the process of source term estimation. Radiological impacts of release to the atmosphere are modelled and calculated across the Europe and displayed in the geographical information system (GIS). The school version of ESTE EU is intended for students of the universities which are interested in or could work in the field of emergency response, radiological and nuclear accidents, dispersion modelling, radiological impacts calculation and urgent or preventive protective measures implementation. The school version of ESTE EU is planned to be donated to specialized departments of faculties in Slovakia, Czech Republic, etc. System can be fully operated in Slovak, Czech or English language. (authors)

School version of ESTE EU

International Nuclear Information System (INIS)

Carny, P.; Suchon, D.; Chyly, M.; Smejkalova, E.; Fabova, V.

2009-01-01

ESTE EU is information system and software for radiological impacts assessment to the territory of the country in case of radiation accident inside/outside of the country .The program enables to model dispersion of radioactive clouds in small-scale and meso-scale. The system enables the user to estimate prediction of the source term (release to the atmosphere ) for any point of radiation/nuclear accident in Europe (for any point of the release, but especially for the sites of European power reactors ). The system enables to utilize results of real radiological monitoring in the process of source term estimation. Radiological impacts of release to the atmosphere are modelled and calculated across the Europe and displayed in the geographical information system (GIS). The school version of ESTE EU is intended for students of the universities which are interested in or could work in the field of emergency response, radiological and nuclear accidents, dispersion modelling, radiological impacts calculation and urgent or preventive protective measures implementation. The school version of ESTE EU is planned to be donated to specialized departments of faculties in Slovakia, Czech Republic, etc. System can be fully operated in Slovak, Czech or English language. (authors)

STATE ACID RAIN RESEARCH AND SCREENING SYSTEM - VERSION 1.0 USER'S MANUAL

Science.gov (United States)

The report is a user's manual that describes Version 1.0 of EPA's STate Acid Rain Research and Screening System (STARRSS), developed to assist utility regulatory commissions in reviewing utility acid rain compliance plans. It is a screening tool that is based on scenario analysis...

BNCT-RTPE: BNCT radiation treatment planning environment

International Nuclear Information System (INIS)

Wessol, D.E.; Wheeler, F.J.; Babcock, R.S.

1995-01-01

Several improvements have been developed for the BNCT radiation treatment planning environment (BNCT-Rtpe) during 1994. These improvements have been incorporated into Version 1.0 of BNCT-Rtpe which is currently installed at the INEL, BNL, Japanese Research Center (JRC), and Finland's Technical Research Center. Platforms supported by this software include Hewlett-Packard (HP), SUN, International Business Machines (IBM), and Silicon Graphics Incorporated (SGI). A draft version of the BNCT-Rtpe user manual is available. Version 1.1 of BNCT-Rtpe is scheduled for release in March 1995. It is anticipated that Version 2.x of BNCT-Rtpe, which includes the nonproprietary NURBS library and data structures, will be released in September 1995

Language sampling

DEFF Research Database (Denmark)

Rijkhoff, Jan; Bakker, Dik

1998-01-01

This article has two aims: [1] to present a revised version of the sampling method that was originally proposed in 1993 by Rijkhoff, Bakker, Hengeveld and Kahrel, and [2] to discuss a number of other approaches to language sampling in the light of our own method. We will also demonstrate how our...... sampling method is used with different genetic classifications (Voegelin & Voegelin 1977, Ruhlen 1987, Grimes ed. 1997) and argue that —on the whole— our sampling technique compares favourably with other methods, especially in the case of exploratory research....

Psychometric properties and validation of the Italian version of the Family Assessment Measure Third Edition – Short Version – in a nonclinical sample

Directory of Open Access Journals (Sweden)

Pellerone M

2017-02-01

Full Text Available Monica Pellerone,1 Tiziana Ramaci,1 Santa Parrello,2 Paola Guariglia,1 Flavio Giaimo1 1Faculty of Human and Social Sciences, “Kore” University of Enna, Enna, 2Department of Humanities Studies, “Federico II” University of Naples, Napoli, Italy Background: Family functioning plays an important role in developing and maintaining dysfunctional behaviors, especially during adolescence. The lack of indicators of family functioning, as determinants of personal and interpersonal problems, represents an obstacle to the activities aimed at developing preventive and intervention strategies. The Process Model of Family Functioning provides a conceptual framework organizing and integrating various concepts into a comprehensive family assessment; this model underlines that through the process of task accomplishment, each family meets objectives central to its life as a group. The Family Assessment Measure Third Edition (FAM III, based on the Process Model of Family Functioning, is among the most frequently used self-report instruments to measure family functioning. Materials and methods: The present study aimed to evaluate the psychometric properties of the Italian version of the Family Assessment Measure Third Edition – Short Version (Brief FAM-III. It consists of three modules: General Scale, which evaluates the family as a system; Dyadic Relationships Scale, which examines how each family member perceives his/her relationship with another member; and Self-Rating Scale, which indicates how each family member is perceived within the nucleus. The developed Brief FAM-III together with the Family Assessment Device were administered to 484 subjects, members of 162 Italian families, formed of 162 fathers aged between 35 and 73 years; 162 mothers aged between 34 and 69 years; and 160 children aged between 12 and 35 years. Correlation, paired-sample t-test, and reliability analyses were carried out. Results: General item analysis shows good indices of

[External cephalic version].

Science.gov (United States)

Navarro-Santana, B; Duarez-Coronado, M; Plaza-Arranz, J

2016-08-01

To analyze the rate of successful external cephalic versions in our center and caesarean sections that would be avoided with the use of external cephalic versions. From January 2012 to March 2016 external cephalic versions carried out at our center, which were a total of 52. We collected data about female age, gestational age at the time of the external cephalic version, maternal body mass index (BMI), fetal variety and situation, fetal weight, parity, location of the placenta, amniotic fluid index (ILA), tocolysis, analgesia, and newborn weight at birth, minor adverse effects (dizziness, hypotension and maternal pain) and major adverse effects (tachycardia, bradycardia, decelerations and emergency cesarean section). 45% of the versions were unsuccessful and 55% were successful. The percentage of successful vaginal delivery in versions was 84% (4% were instrumental) and 15% of caesarean sections. With respect to the variables studied, only significant differences in birth weight were found; suggesting that birth weight it is related to the outcome of external cephalic version. Probably we did not find significant differences due to the number of patients studied. For women with breech presentation, we recommend external cephalic version before the expectant management or performing a cesarean section. The external cephalic version increases the proportion of fetuses in cephalic presentation and also decreases the rate of caesarean sections.

Korean Version of Inventory of Complicated Grief Scale: Psychometric Properties in Korean Adolescents.

Science.gov (United States)

Han, Doug Hyun; Lee, Jung Jae; Moon, Duk-Soo; Cha, Myoung-Jin; Kim, Min A; Min, Seonyeong; Yang, Ji Hoon; Lee, Eun Jeong; Yoo, Seo Koo; Chung, Un-Sun

2016-01-01

We aimed to validate the Inventory of Complicated Grief (ICG)-Korean version among 1,138 Korean adolescents, representing a response rate of 57% of 1,997 students. Participants completed a set of questionnaires including demographic variables (age, sex, years of education, experience of grief), the ICG, the Children's Depression Inventory (CDI) and the Lifetime Incidence of Traumatic Events-Child (LITE-C). Exploratory factor analysis was performed to determine whether the ICG items indicated complicated grief in Korean adolescents. The internal consistency of the ICG-Korean version was Cronbach's α=0.87. The test-retest reliability for a randomly selected sample of 314 participants in 2 weeks was r=0.75 (PKaiser-Meyer-Olkin Measure of Sampling Adequacy=0.911; Bartlett's Test of Sphericity, χ(2)=13,144.7, P<0.001). After omission of 3 items, the value of Cronbach's α increased from 0.87 for the 19-item ICG-Korean version to 0.93 for the 16-item ICG-Korean version. These results suggest that the ICG is a useful tool in assessing for complicated grief in Korean adolescents. However, the 16-item version of the ICG appeared to be more valid compared to the 19-item version of the ICG. We suggest that the 16-item version of the ICG be used to screen for complicated grief in Korean adolescents.

Oncentra brachytherapy planning system.

Science.gov (United States)

Yang, Jack

2018-03-27

In modern cancer management, treatment planning has progressed as a contemporary tool with all the advances in computing power in recent years. One of the advanced planning tools uses 3-dimensional (3D) data sets for accurate dose distributions in patient prescription. Among these planning processes, brachytherapy has been a very important part of a successful cancer management program, offering clinical benefits with specific or combined treatments with external beam therapy. In this chapter, we mainly discussed the Elekta Oncentra planning system, which is the main treatment planning tool for high-dose rate (HDR) modality in our facility and in many other facilities in the United States. HDR is a technically advanced form of brachytherapy; a high-intensity radiation source (3.6 mm in length) is delivered with step motor in submillimeter precision under computer guidance directly into the tumor areas while minimizing injury to surrounding normal healthy tissue. Oncentra planning is the key component to generate a deliverable brachytherapy procedure, which is executed on the microSelectron V3 remote afterloader treatment system. Creating a highly conformal plan can be a time-consuming task. The development of Oncentra software (version 4.5.3) offers a variety of useful tools that facilitate many of the clinical challenging tasks for planning, such as contouring and image reconstruction, as well as rapid planning calculations with dose and dose volume histogram analysis. Oncentra Brachy module creates workflow and optimizes the planning accuracy for wide varieties of clinical HDR treatments, such as skin, gynecologic (GYN), breast, prostate, and many other applications. The treatment file can also be transferred to the afterloader control station for speedy delivery. The design concept, calculation algorithms, and optimization modules presented some key characteristics to plan and treat the patients effectively and accurately. The dose distribution and accuracy of

R7 VU Born-Assessed Demo Plan

Energy Technology Data Exchange (ETDEWEB)

Robert Nourgaliev

2010-02-01

This is an initial draft of a born-assessed VU plan for the RELAP7 (R7) code development effort. The plan will continue to evolve based on the growth of code capability. This growth will be reflected as additional testing is identified and done. Later versions of this document will reflect that growth.

Spatial Distribution and Sampling Plans With Fixed Level of Precision for Citrus Aphids (Hom., Aphididae) on Two Orange Species.

Science.gov (United States)

Kafeshani, Farzaneh Alizadeh; Rajabpour, Ali; Aghajanzadeh, Sirous; Gholamian, Esmaeil; Farkhari, Mohammad

2018-04-02

Aphis spiraecola Patch, Aphis gossypii Glover, and Toxoptera aurantii Boyer de Fonscolombe are three important aphid pests of citrus orchards. In this study, spatial distributions of the aphids on two orange species, Satsuma mandarin and Thomson navel, were evaluated using Taylor's power law and Iwao's patchiness. In addition, a fixed-precision sequential sampling plant was developed for each species on the host plant by Green's model at precision levels of 0.25 and 0.1. The results revealed that spatial distribution parameters and therefore the sampling plan were significantly different according to aphid and host plant species. Taylor's power law provides a better fit for the data than Iwao's patchiness regression. Except T. aurantii on Thomson navel orange, spatial distribution patterns of the aphids were aggregative on both citrus. T. aurantii had regular dispersion pattern on Thomson navel orange. Optimum sample size of the aphids varied from 30-2061 and 1-1622 shoots on Satsuma mandarin and Thomson navel orange based on aphid species and desired precision level. Calculated stop lines of the aphid species on Satsuma mandarin and Thomson navel orange ranged from 0.48 to 19 and 0.19 to 80.4 aphids per 24 shoots according to aphid species and desired precision level. The performance of the sampling plan was validated by resampling analysis using resampling for validation of sampling plans (RVSP) software. This sampling program is useful for IPM program of the aphids in citrus orchards.

Automated Procurement System (APS): Project management plan (DS-03), version 1.2

Science.gov (United States)

Murphy, Diane R.

1994-01-01

The National Aeronautics and Space Administration (NASA) Marshall Space Flight Center (MSFC) is implementing an Automated Procurement System (APS) to streamline its business activities that are used to procure goods and services. This Project Management Plan (PMP) is the governing document throughout the implementation process and is identified as the APS Project Management Plan (DS-03). At this point in time, the project plan includes the schedules and tasks necessary to proceed through implementation. Since the basis of APS is an existing COTS system, the implementation process is revised from the standard SDLC. The purpose of the PMP is to provide the framework for the implementation process. It discusses the roles and responsibilities of the NASA project staff, the functions to be performed by the APS Development Contractor (PAI), and the support required of the NASA computer support contractor (CSC). To be successful, these three organizations must work together as a team, working towards the goals established in this Project Plan. The Project Plan includes a description of the proposed system, describes the work to be done, establishes a schedule of deliverables, and discusses the major standards and procedures to be followed.

NETS - A NEURAL NETWORK DEVELOPMENT TOOL, VERSION 3.0 (MACHINE INDEPENDENT VERSION)

Science.gov (United States)

Baffes, P. T.

1994-01-01

allows the user to generate C code to implement the network loaded into the system. This permits the placement of networks as components, or subroutines, in other systems. In short, once a network performs satisfactorily, the Generate C Code option provides the means for creating a program separate from NETS to run the network. Other features: files may be stored in binary or ASCII format; multiple input propagation is permitted; bias values may be included; capability to scale data without writing scaling code; quick interactive testing of network from the main menu; and several options that allow the user to manipulate learning efficiency. NETS is written in ANSI standard C language to be machine independent. The Macintosh version (MSC-22108) includes code for both a graphical user interface version and a command line interface version. The machine independent version (MSC-21588) only includes code for the command line interface version of NETS 3.0. The Macintosh version requires a Macintosh II series computer and has been successfully implemented under System 7. Four executables are included on these diskettes, two for floating point operations and two for integer arithmetic. It requires Think C 5.0 to compile. A minimum of 1Mb of RAM is required for execution. Sample input files and executables for both the command line version and the Macintosh user interface version are provided on the distribution medium. The Macintosh version is available on a set of three 3.5 inch 800K Macintosh format diskettes. The machine independent version has been successfully implemented on an IBM PC series compatible running MS-DOS, a DEC VAX running VMS, a SunIPC running SunOS, and a CRAY Y-MP running UNICOS. Two executables for the IBM PC version are included on the MS-DOS distribution media, one compiled for floating point operations and one for integer arithmetic. The machine independent version is available on a set of three 5.25 inch 360K MS-DOS format diskettes (standard

Determination of the influence of dispersion pattern of pesticide-resistant individuals on the reliability of resistance estimates using different sampling plans.

Science.gov (United States)

Shah, R; Worner, S P; Chapman, R B

2012-10-01

Pesticide resistance monitoring includes resistance detection and subsequent documentation/ measurement. Resistance detection would require at least one (≥1) resistant individual(s) to be present in a sample to initiate management strategies. Resistance documentation, on the other hand, would attempt to get an estimate of the entire population (≥90%) of the resistant individuals. A computer simulation model was used to compare the efficiency of simple random and systematic sampling plans to detect resistant individuals and to document their frequencies when the resistant individuals were randomly or patchily distributed. A patchy dispersion pattern of resistant individuals influenced the sampling efficiency of systematic sampling plans while the efficiency of random sampling was independent of such patchiness. When resistant individuals were randomly distributed, sample sizes required to detect at least one resistant individual (resistance detection) with a probability of 0.95 were 300 (1%) and 50 (10% and 20%); whereas, when resistant individuals were patchily distributed, using systematic sampling, sample sizes required for such detection were 6000 (1%), 600 (10%) and 300 (20%). Sample sizes of 900 and 400 would be required to detect ≥90% of resistant individuals (resistance documentation) with a probability of 0.95 when resistant individuals were randomly dispersed and present at a frequency of 10% and 20%, respectively; whereas, when resistant individuals were patchily distributed, using systematic sampling, a sample size of 3000 and 1500, respectively, was necessary. Small sample sizes either underestimated or overestimated the resistance frequency. A simple random sampling plan is, therefore, recommended for insecticide resistance detection and subsequent documentation.

300-FF-1 remedial action sampling and analysis plan DQO process summary report

International Nuclear Information System (INIS)

Carlson, R.A.

1997-01-01

The scope of the 300-FF-1 Operable Unit (OU) data quality objective (DQO) process includes the soil and debris from the waste sites identified in the Proposed Plan for the 300-FF-1 and 300-FF-5 Operable units and, as the DQO process evolved, refined by the 300-FF-1 Record of Decision (ROD). Exclusions are identified in Section 1.3. The 300-FF-1 waste sites are addressed throughout the DQO process as they were subdivided in the proposed plan. The waste sites are divided into areas or zones known to be above the cleanup standards, zones below the cleanup standards, and zones where the contamination level is currently unknown. The project objectives are (1) to identify the criteria by which 300-FF-1 contaminated soil and debris may be shipped to the Environmental Restoration Disposal Facility (ERDF), (2) to identify the criteria by which the 300-FF-1 waste sites can be demonstrated as meeting the cleanup criteria, and (3) to develop a sampling and analysis plan (SAP) that adequately allows the evaluation of soil and debris analysis against the criteria

Guidance document for preparing water sampling and analysis plans for UMTRA Project sites. Revision 1

International Nuclear Information System (INIS)

1995-09-01

A water sampling and analysis plan (WSAP) is prepared for each Uranium Mill Tailings Remedial Action (UMTRA) Project site to provide the rationale for routine ground water sampling at disposal sites and former processing sites. The WSAP identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the routine ground water monitoring stations at each site. This guidance document has been prepared by the Technical Assistance Contractor (TAC) for the US Department of Energy (DOE). Its purpose is to provide a consistent technical approach for sampling and monitoring activities performed under the WSAP and to provide a consistent format for the WSAP documents. It is designed for use by the TAC in preparing WSAPs and by the DOE, US Nuclear Regulatory Commission, state and tribal agencies, other regulatory agencies, and the public in evaluating the content of WSAPS

A model national emergency response plan for radiological accidents

International Nuclear Information System (INIS)

1993-09-01

The IAEA has supported several projects for the development of a national response plan for radiological emergencies. As a results, the IAEA has developed a model National Emergency Response Plan for Radiological Accidents (RAD PLAN), particularly for countries that have no nuclear power plants. This plan can be adapted for use by countries interested in developing their own national radiological emergency response plan, and the IAEA will supply the latest version of the RAD PLAN on computer diskette upon request. 2 tabs

Field Sampling Plan for Closure of the Central Facilities Area Sewage Treatment Plant Lagoon 3 and Land Application Area

International Nuclear Information System (INIS)

Lewis, Michael George

2016-01-01

This field sampling plan describes sampling of the soil/liner of Lagoon 3 at the Central Facilities Area Sewage Treatment Plant. The lagoon is to be closed, and samples obtained from the soil/liner will provide information to determine if Lagoon 3 and the land application area can be closed in a manner that renders it safe to human health and the environment. Samples collected under this field sampling plan will be compared to Idaho National Laboratory background soil concentrations. If the concentrations of constituents of concern exceed the background level, they will be compared to Comprehensive Environmental Response, Compensation, and Liability Act preliminary remediation goals and Resource Conservation and Recovery Act levels. If the concentrations of constituents of concern are lower than the background levels, Resource Conservation and Recovery Act levels, or the preliminary remediation goals, then Lagoon 3 and the land application area will be closed. If the Resource Conservation and Recovery Act levels and/or the Comprehensive Environmental Response, Compensation, and Liability Act preliminary remediation goals are exceeded, additional sampling and action may be required.

Field Sampling Plan for Closure of the Central Facilities Area Sewage Treatment Plant Lagoon 3 and Land Application Area

Energy Technology Data Exchange (ETDEWEB)

Lewis, Michael George [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-10-01

This field sampling plan describes sampling of the soil/liner of Lagoon 3 at the Central Facilities Area Sewage Treatment Plant. The lagoon is to be closed, and samples obtained from the soil/liner will provide information to determine if Lagoon 3 and the land application area can be closed in a manner that renders it safe to human health and the environment. Samples collected under this field sampling plan will be compared to Idaho National Laboratory background soil concentrations. If the concentrations of constituents of concern exceed the background level, they will be compared to Comprehensive Environmental Response, Compensation, and Liability Act preliminary remediation goals and Resource Conservation and Recovery Act levels. If the concentrations of constituents of concern are lower than the background levels, Resource Conservation and Recovery Act levels, or the preliminary remediation goals, then Lagoon 3 and the land application area will be closed. If the Resource Conservation and Recovery Act levels and/or the Comprehensive Environmental Response, Compensation, and Liability Act preliminary remediation goals are exceeded, additional sampling and action may be required.

Specified assurance level sampling procedure

International Nuclear Information System (INIS)

Willner, O.

1980-11-01

In the nuclear industry design specifications for certain quality characteristics require that the final product be inspected by a sampling plan which can demonstrate product conformance to stated assurance levels. The Specified Assurance Level (SAL) Sampling Procedure has been developed to permit the direct selection of attribute sampling plans which can meet commonly used assurance levels. The SAL procedure contains sampling plans which yield the minimum sample size at stated assurance levels. The SAL procedure also provides sampling plans with acceptance numbers ranging from 0 to 10, thus, making available to the user a wide choice of plans all designed to comply with a stated assurance level

Advantages of three-dimensional treatment planning in radiation therapy

International Nuclear Information System (INIS)

Attalla, E.M.; ELSAyed, A.A.; ElGantiry, M.; ElTahher, Z.

2003-01-01

This study was designed to demonstrate the feasibility of three-dimensional (3-D) treatment planning in-patients maxilla, breast, bladder, and lung tumors to explore its potential therapeutic advantage over the traditional dimensional (2-D) approach in these diseases. Conventional two-dimensional (2-D) treatment planning was compared to three-dimensional (3-D) treatment planning. In five selected disease sites, plans calculated with both types of treatment planning were compared. The (3-D) treatment planning system used in this work TMS version 5.1 B from helax AB is based on a monte Carlo-based pencil beam model. The other treatment planning system (2-D 0, introduced in this study was the multi data treatment planning system version 2.35. For the volumes of interest; quality of dose distribution concerning homogeneity in the target volume and the isodose distribution in organs at risk, was discussed. Qualitative and quantitative comparisons between the two planning systems were made using dose volume histograms (DVH's) . For comparisons of dose distributions in real-patient cases, differences ranged from 0.8% to 6.4% for 6 MV, while in case of 18 MV photon, it ranged from 1,8% to 6.5% and was within -+3 standard deviations for the dose between the two planning systems.Dose volume histogram (DVH) shows volume reduction of the radiation-related organs at risk 3-D planning

The Factor Structure and Psychometric Properties of the Persian Version of the Revised Prenatal Coping Inventory (Nu-PCI).

Science.gov (United States)

Faramarzi, Mahbobeh; Pasha, Hajar; Khafri, Sorayya; Heidary, Shima

2017-03-01

Familiarity with coping strategies is essential for stress management during pregnancy. The Revised Prenatal Coping Inventory (Nu-PCI) was developed to assess coping strategies during pregnancy. This study aimed to assess the factor structure and psychometric properties of the Persian version of the Nu-PCI. After forward-backward translation, the Nu-PCI was administered to 210 pregnant women who were enrolled in two teaching referral clinics in the North of the Islamic Republic of Iran (Babol). The participants completed the Persian Nu-PCI and Ways of Coping Questionnaire (WCQ), which was used to determine the validity of the Persian Nu-PCI. To test construct validity of the Persian Nu-PCI, a principal components factor analysis was performed. Principal components analysis with varimax rotation showed a best fitting 3-factor structure similar to the original with three coping subscales: planning-preparation, avoidance, and spiritual-positive coping. The Persian Nu-PCI was internally consistent and within the acceptable range (α=0.89-0.97). The alpha coefficients for the Nu-PCI and the subscales of planning-preparation, avoidance, and spiritual-positive coping were high. Test-retest coefficients for the Nu-PCI and subscales were 0.98-0.99. The Nu-PCI and its subscales correlated with the WCQ in the entire sample and within each trimester. The Persian version of the Nu-PCI and the subscales of planning-preparation, avoidance, and spiritual-positive coping represent the first reliable standardized tool for measuring coping strategies during pregnancy in the Islamic Republic of Iran. Therefore, it can be applied as a quick and accurate preliminary screening tool for evaluating coping strategies throughout pregnancy in clinics and other medical and research settings.

Global Precipitation Climatology Project (GPCP) - Monthly, Version 2.2 (Version Superseded)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Version 2.2 of the dataset has been superseded by a newer version. Users should not use version 2.2 except in rare cases (e.g., when reproducing previous studies...

Screening efficiency of the self-report version of the Multidimensional Anxiety Scale for Children in a highly comorbid inpatient sample.

Science.gov (United States)

Skarphedinsson, Gudmundur; Villabø, Marianne A; Lauth, Bertrand

2015-01-01

The Multidimensional Anxiety Scale for Children (MASC) is a widely used self-report questionnaire for the assessment of anxiety symptoms in children and adolescents with well documented predictive validity of the total score and subscales in internalizing and mixed clinical samples. However, no data exist on the screening efficiency in an inpatient sample of adolescents. To examine the psychometric properties and screening efficiency of the MASC in a high comorbid inpatient sample. The current study used receiver operating characteristic (ROC) analyses to investigate the predictive value of the MASC total and subscale scores for the Schedule for Affective Disorders and Schizophrenia for School-age children-Present and Lifetime version (K-SADS-PL), DSM-IV diagnoses of generalized anxiety disorder (GAD), separation anxiety disorder (SAD) and social phobia (SoP) in a highly comorbid inpatient sample of adolescents (11-18 years). The MASC total score predicted any anxiety disorder (AD) and GAD moderately well. Physical symptoms predicted GAD moderately well. Social anxiety and separation anxiety/panic did not predict SoP or SAD, respectively. Physical symptoms and harm avoidance also predicted the presence of major depressive disorder. The findings support the utility of the MASC total score to predict the presence of any AD and GAD. However, the utility of the social anxiety and separation anxiety/panic subscales showed limited utility to predict the presence of SAD and SoP, respectively. The MASC has probably a more limited function in screening for AD among a highly comorbid inpatient sample of severely affected adolescents. Our results should be interpreted in the light of a small, mixed sample of inpatient adolescents.

29 CFR 1952.380 - Description of the plan.

Science.gov (United States)

2010-07-01

... OSHA standards exist. The plan provides that program personnel will be employed under a merit system... version of OSHA standards be made available within three years of plan approval. (c) The Puerto Rico Act... against employers for violations of standards and orders; and review of citations by a hearing examiner...

UMTRA project water sampling and analysis plan, Grand Junction, Colorado

International Nuclear Information System (INIS)

1994-07-01

Surface remedial action will be completed at the Grand Junction processing site during the summer of 1994. Results of 1993 water sampling indicate that ground water flow conditions and ground water quality at the processing site have remained relatively constant with time. Uranium concentrations in ground water continue to exceed the maximum concentration limits, providing the best indication of the extent of contaminated ground water. Evaluation of surface water quality of the Colorado River indicate no impact from uranium processing activities. No compliance monitoring at the Cheney disposal site has been proposed because ground water in the Dakota Sandstone (uppermost aquifer) is classified as limited-use (Class 111) and because the disposal cell is hydrogeologically isolated from the uppermost aquifer. The following water sampling and water level monitoring activities are planned for calendar year 1994: (i) Semiannual (early summer and late fall) sampling of six existing monitor wells at the former Grand Junction processing site. Analytical results from this sampling will be used to continue characterizing hydrogeochemical trends in background ground water quality and in the contaminated ground water area resulting from source term (tailings) removal. (ii) Water level monitoring of approximately three proposed monitor wells projected to be installed in the alluvium at the processing site in September 1994. Data loggers will be installed in these wells, and water levels will be electronically monitored six times a day. These long-term, continuous ground water level data will be collected to better understand the relationship between surface and ground water at the site. Water level and water quality data eventually will be used in future ground water modeling to establish boundary conditions in the vicinity of the Grand Junction processing site. Modeling results will be used to help demonstrate and document the potential remedial alternative of natural flushing

Diagnostic Accuracy of the Posttraumatic Stress Disorder Checklist–Civilian Version in a Representative Military Sample

DEFF Research Database (Denmark)

Karstoft, Karen-Inge; Andersen, Søren B.; Bertelsen, Mette

2014-01-01

This study aimed to assess the diagnostic accuracy of the Posttraumatic Stress Disorder Checklist-Civilian Version (PCL-C; Weathers, Litz, Herman, Huska, & Keane, 1993) and to establish the most accurate cutoff for prevalence estimation of posttraumatic stress disorder (PTSD) in a representative...

Spanish version validation of the Marihuana Motives Measure in a drug-consuming adolescent sample.

Science.gov (United States)

Matali Costa, Josep; Simons, J; Pardo, M; Lleras, M; Pérez, A; Andión, O

2018-01-15

Cannabis is the illicit drug mostly widely consumed by adolescents in Spain. The understanding of consumption motives is an important factor for intervention. In Spain, there are no available instruments for their evaluation, hence, the goal of this paper is to study the psychometric properties of the Marihuana Motives Measure (MMM) in a sample of adolescent consumers. Firstly, translation and back-translation was performed. A total of 228 adolescent consumers of cannabis were evaluated. Factorial analysis was conducted, and the reliability of the total scores and of each scale of the questionnaire was studied through Cronbach's alpha. Test-retest reliability was analyzed through interclass correlations. Validity evidence of the MMM was examined through correlations between current cannabis use, subjective consumption effects measured with the Addiction Research Center Inventory (ARCI), and personality measured with the Millon Adolescent Clinical Inventory (MACI). High reliability was observed in total score of the MMM (Cronbach α = .86), and high and moderate reliability for each of the five factors obtained in the factorial analysis of the MMM, Social = .82, Enhancement = .72, Coping = .83, Expansion = .74, and Conformity = .64. Significant correlations were also observed between cannabis consumption motives and subjective effects, and between consumption motives and personality. The Spanish version of the MMM shows a similar factorial structure as the one obtained by the original author, and its measures are reliable and valid for the study of cannabis consumption motives in adolescent consumer population.

Development of the Brazilian version of the Child Hayling Test

Directory of Open Access Journals (Sweden)

Larissa de Souza Siqueira

Full Text Available Abstract Introduction: The Hayling Test assesses the components of initiation, inhibition, cognitive flexibility and verbal speed by means of a sentence completion task. This study presents the process of developing the Brazilian version of the Child Hayling Test (CHT and reports evidence of its content validity. Methods: 139 people took part in the study. The adaptation was performed by seven translators and 12 specialist judges. An initial sample of 92 healthy children was recruited to test a selection of sentences adapted from previous adult and pediatric versions of the instrument, and a sample of 28 healthy children was recruited for pilot testing of the final version. The instrument was developed in seven stages: 1 translation, 2 back-translation, 3 comparison of translated versions, 4 preparation of new stimuli, 5 data collection with healthy children to analyze comprehension of the stimuli and analyses by the authors against the psycholinguistic criteria adopted, 6 analyses conducted by judges who are specialists in neuropsychology or linguistics, and 7 the pilot study. Results: Twenty-four of the 72 sentences constructed were selected on the basis of 70-100% agreement between judges evaluating what they assessed and level of comprehensibility. The pilot study revealed better performance by older children, providing evidence of the instrument's sensitivity to developmental factors. Conclusions: Future studies employing this version of CHT with clinical pediatric populations who have frontal lesions and dysfunctions and in related areas are needed to test functional and differential diagnoses of preserved or impaired executive functions.

Zoonoses action plan Salmonella monitoring programme: an investigation of the sampling protocol.

Science.gov (United States)

Snary, E L; Munday, D K; Arnold, M E; Cook, A J C

2010-03-01

The Zoonoses Action Plan (ZAP) Salmonella Programme was established by the British Pig Executive to monitor Salmonella prevalence in quality-assured British pigs at slaughter by testing a sample of pigs with a meat juice enzyme-linked immunosorbent assay for antibodies against group B and C(1) Salmonella. Farms were assigned a ZAP level (1 to 3) depending on the monitored prevalence, and ZAP 2 or 3 farms were required to act to reduce the prevalence. The ultimate goal was to reduce the risk of human salmonellosis attributable to British pork. A mathematical model has been developed to describe the ZAP sampling protocol. Results show that the probability of assigning a farm the correct ZAP level was high, except for farms that had a seroprevalence close to the cutoff points between different ZAP levels. Sensitivity analyses identified that the probability of assigning a farm to the correct ZAP level was dependent on the sensitivity and specificity of the test, the number of batches taken to slaughter each quarter, and the number of samples taken per batch. The variability of the predicted seroprevalence was reduced as the number of batches or samples increased and, away from the cutoff points, the probability of being assigned the correct ZAP level increased as the number of batches or samples increased. In summary, the model described here provided invaluable insight into the ZAP sampling protocol. Further work is required to understand the impact of the program for Salmonella infection in British pig farms and therefore on human health.

Preliminary analyses of psychometric characteristics of the Polish version of the Obsessive-Compulsive Inventory-Revised (OCI-R in a non-clinical sample

Directory of Open Access Journals (Sweden)

Justyna Mojsa-Kaja

2016-12-01

Full Text Available Objectives: Obsessive-compulsive disorder (OCD is an anxiety-spectrum disorder that affects 1–2% of the adult population. People with OCD are more likely to report impaired social and occupational functioning. Although effective treatments of the OCD exist, many sufferers from this disorder are continuously misdiagnosed. Therefore, improving the assessment of the OCD remains an important area of scientific research. The main goal of the study is the initial verification of psychometric properties in the Polish version of the Obsessive-Compulsive Inventory-Revised (OCI-R in a college student sample. Material and Methods: A group of students completed a battery of measures consisting of obsessive-compulsive symptoms (The OCI-R, The Yale-Brown Obsessive Compulsive Scale, depression (The Beck Depression Inventory and anxiety trait (The State-Trait Anxiety Inventory. Results: A confirmatory factor analysis, conducted on data from 334 university students, supported a solid and replicable 6-fold factor structure of the OCI-R. Further analyses on test-retest reliability (following a 1-month interval, convergent and divergent validity of the OCI-R were respectively conducted in a group of 137 students who had completed a battery of measures mentioned above. The results showed adequate testretest reliability for the full scale and subscales cores, high internal consistency and confirmed satisfactory convergent and divergent validity. Conclusions: The study constitutes the first phase of work on a Polish version of measurement for obsessive-compulsive symptoms. Satisfactory results obtained in a non-clinical sample allow to recognize this method to be promising for further research. Int J Occup Med Environ Health 2016;29(6:1011–1021

Technology Development and Advanced Planning for Curation of Returned Mars Samples

Science.gov (United States)

Lindstrom, David J.; Allen, Carlton C.

2002-01-01

NASA Johnson Space Center (JSC) curates extraterrestrial samples, providing the international science community with lunar rock and soil returned by the Apollo astronauts, meteorites collected in Antarctica, cosmic dust collected in the stratosphere, and hardware exposed to the space environment. Curation comprises initial characterization of new samples, preparation and allocation of samples for research, and clean, secure long-term storage. The foundations of this effort are the specialized cleanrooms (class 10 to 10,000) for each of the four types of materials, the supporting facilities, and the people, many of whom have been doing detailed work in clean environments for decades. JSC is also preparing to curate the next generation of extraterrestrial samples. These include samples collected from the solar wind, a comet, and an asteroid. Early planning and R\\&D are underway to support post-mission sample handling and curation of samples returned from Mars. One of the strong scientific reasons for returning samples from Mars is to search for evidence of current or past life in the samples. Because of the remote possibility that the samples may contain life forms that are hazardous to the terrestrial biosphere, the National Research Council has recommended that all samples returned from Mars be kept under strict biological containment until tests show that they can safely be released to other laboratories. It is possible that Mars samples may contain only scarce or subtle traces of life or prebiotic chemistry that could readily be overwhelmed by terrestrial contamination . Thus, the facilities used to contain, process, and analyze samples from Mars must have a combination of high-level biocontainment and organic / inorganic chemical cleanliness that is unprecedented. JSC has been conducting feasibility studies and developing designs for a sample receiving facility that would offer biocontainment at least the equivalent of current maximum containment BSL-4 (Bio

Dispersion patterns and sampling plans for Diaphorina citri (Hemiptera: Psyllidae) in citrus.

Science.gov (United States)

Sétamou, Mamoudou; Flores, Daniel; French, J Victor; Hall, David G

2008-08-01

The abundance and spatial dispersion of Diaphorina citri Kuwayama (Hemiptera: Psyllidae) were studied in 34 grapefruit (Citrus paradisi Macfad.) and six sweet orange [Citrus sinensis (L.) Osbeck] orchards from March to August 2006 when the pest is more abundant in southern Texas. Although flush shoot infestation levels did not vary with host plant species, densities of D. citri eggs, nymphs, and adults were significantly higher on sweet orange than on grapefruit. D. citri immatures also were found in significantly higher numbers in the southeastern quadrant of trees than other parts of the canopy. The spatial distribution of D. citri nymphs and adults was analyzed using Iowa's patchiness regression and Taylor's power law. Taylor's power law fitted the data better than Iowa's model. Based on both regression models, the field dispersion patterns of D. citri nymphs and adults were aggregated among flush shoots in individual trees as indicated by the regression slopes that were significantly >1. For the average density of each life stage obtained during our surveys, the minimum number of flush shoots per tree needed to estimate D. citri densities varied from eight for eggs to four flush shoots for adults. Projections indicated that a sampling plan consisting of 10 trees and eight flush shoots per tree would provide density estimates of the three developmental stages of D. citri acceptable enough for population studies and management decisions. A presence-absence sampling plan with a fixed precision level was developed and can be used to provide a quick estimation of D. citri populations in citrus orchards.

Global Historical Climatology Network (GHCN), Version 1 (Version Superseded)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Please note, this dataset has been superseded by a newer version (see below). Users should not use this version except in rare cases (e.g., when reproducing previous...

Psychometric evaluation of the Chinese version of short-form Test of Functional Health Literacy in Adolescents.

Science.gov (United States)

Chang, Li-Chun; Hsieh, Pei-Lin; Liu, Chieh-Hsing

2012-09-01

The purpose of this study is to develop and evaluate the psychometric properties of the Chinese version of short-form Test of Functional Health Literacy in Adolescents. Assessing health literacy is vital to design health education programme; however, there are no measurement tools exist for use specifically in Chinese adolescents. A non-experimental design was used to test the psychometric properties of the Test of Functional Health Literacy in Adolescents. The short-form Test of Functional Health Literacy in Adolescents was translated and back translated into a Chinese language version. Thirty high school students were recruited to validate the scenario of Test of Functional Health Literacy in Adolescents. Based on the multiple-stage stratified random sampling method, 300 high school students from four counties in Taiwan were invited to participate in this study to evaluate the psychometric properties of Test of Functional Health Literacy in Adolescents. The Functional Health Literacy in Adolescents had good internal consistency reliability and excellent test-retest reliability. Confirmatory factor analysis resulted in a one-factor solution. Contrary to the original version of the Test of Functional Health Literacy in Adolescents, the findings revealed that the 36-item, one-factor model for the Test of Functional Health Literacy in Adolescents is the best-fit model. This is a suitable instrument to assess health literacy levels in Chinese adolescents before health education programmes can be appropriately planned, implemented and evaluated. © 2012 Blackwell Publishing Ltd.

Psychometric properties of the Turkish version of the 42 item Depression Anxiety Stress Scale (DASS-42) in a clinical sample.

Science.gov (United States)

Hekimoglu, Levent; Altun, Zeren Ozturk; Kaya, Emine Zeynep; Bayram, Nuran; Bilgel, Nazan

2012-01-01

To study the psychometric properties of the Turkish translation of the Depression Anxiety and Stress Scale (DASS-42) in a clinical group. Outpatients diagnosed with anxiety (n = 138; mean age = 44.5 years; 74.6% female) or depression (n = 112; mean age = 46.2 years; 77.7% female) from the psychiatric outpatient clinic of a public hospital were evaluated. A group of non-clinical volunteers (n = 250; mean age = 37 years; 68% female) served as a community group for comparison. The participants completed the Turkish versions of the DASS-42, the Beck Depression Inventory (BDI), and the Beck Anxiety Inventory (BAI). The structure of the DASS-42 was analyzed in the clinical sample using principal components extraction. The three-factor solution accounted for 56% of the total variance, with eigenvalues of 17.6, 3.0, and 2.6. The range of factor loadings was 0.55-0.85 for depression, 0.47-0.62 for anxiety, and 0.49-0.74 for stress. The Cronbach alpha values for the DASS depression, anxiety, and stress subscales were 0.94, 0.88, 0.94 respectively. The concurrent validity of the DASS was satisfactory. The non-clincal participants scored lower on all three subscales than the individuals in all of the clinical groups. The Turkish version of the DASS-42 appears to be an excellent instrument for measuring features of depression, hyperarousal, and tension in clinical groups.

Procedure guidelines for radioiodine therapy of differentiated thyroid cancer (version 3); Verfahrensanweisung zur Radioiodtherapie (RIT) beim differenzierten Schilddruesenkarzinom (Version 3)

Energy Technology Data Exchange (ETDEWEB)

Dietlein, M.; Schicha, H. [Deutsche Gesellschaft fuer Nuklearmedizin (DGN) (Germany); Koeln Univ. (Germany). Klinik und Poliklinik fuer Nuklearmedizin; Dressler, J. [Deutsche Gesellschaft fuer Nuklearmedizin (DGN) (Germany); Nuklearmedizinsiche Klinik der Henriettenstiftung, Hannover (Germany); Eschner, W. [Deutsche Gesellschaft fuer Nuklearmedizin (DGN) (Germany); Deutsche Gesellschaft fuer Medizinische Physik (DGMP) (Germany); Koeln Univ. (Germany). Klinik und Poliklinik fuer Nuklearmedizin; Gruenwald, F. [Deutsche Gesellschaft fuer Nuklearmedizin (DGN) (Germany); Frankfurt Univ. (Germany). Klinik und Poliklinik fuer Nuklearmedizin; Lassmann, M. [Deutsche Gesellschaft fuer Nuklearmedizin (DGN) (Germany); Deutsche Gesellschaft fuer Medizinische Physik (DGMP) (Germany); Wuerzburg Univ. (Germany). Klinik und Poliklinik fuer Nuklearmedizin; Leisner, B. [Deutsche Gesellschaft fuer Nuklearmedizin (DGN) (Germany); Allgemeines Krankenhaus St. Georg, Hamburg (Germany); Luster, M.; Reiners, C. [Deutsche Gesellschaft fuer Nuklearmedizin (DGN) (Germany); Wuerzburg Univ. (Germany). Klinik und Poliklinik fuer Nuklearmedizin; Moser, E. [Deutsche Gesellschaft fuer Nuklearmedizin (DGN) (Germany); Radiologische Universitaetsklinik Freiburg (Germany); Schober, O. [Deutsche Gesellschaft fuer Nuklearmedizin (DGN) (Germany); Muenster Univ. (Germany). Klinik und Poliklinik fuer Nuklearmedizin

2007-07-01

The procedure guideline for radioiodine therapy (RIT) of differentiated thyroid cancer (version 3) is the counterpart to the procedure guideline for {sup 131}I whole-body scintigraphy (version 3) and specify the interdisciplinary guideline for thyroid cancer of the Deutsche Krebsgesellschaft concerning the nuclear medicine part. Recommendation for ablative {sup 131}I therapy is given for all differentiated thyroid carcinoma (DTC) >1 cm. Regarding DTC {<=}1 cm {sup 131}I ablation may be helpful in an individual constellation. Preparation for {sup 131}I ablation requires low iodine diet for two weeks and TSH stimulation by withdrawal of thyroid hormone medication or by use of recombinant human TSH (rhTSH). The advantages of rhTSH (no symptoms of hypothyroidism, lowerblood activity) and the advantages of endogenous TSH stimulation (necessary for {sup 131}I-therapy in patients with metastases, higher sensitivity of {sup 131}I whole-body scan) are discussed. In most centers standard activities are used for {sup 131}I ablation. If pretherapeutic dosimetry is planned, the diagnostic administration of {sup 131}I should not exceed 1-10MBq, alternative tracers are {sup 123}I or {sup 124}I. The recommendations for contraception and family planning are harmonized with the recommendation of ATA and ETA. Regarding the best possible protection of salivary glands the evidence is insufficient to recommend a specific setting. To minimize the risk of dental caries due to xerostomia patients should use preventive strategies for dental hygiene. (orig.)

Verification of RESRAD-build computer code, version 3.1

International Nuclear Information System (INIS)

2003-01-01

RESRAD-BUILD is a computer model for analyzing the radiological doses resulting from the remediation and occupancy of buildings contaminated with radioactive material. It is part of a family of codes that includes RESRAD, RESRAD-CHEM, RESRAD-RECYCLE, RESRAD-BASELINE, and RESRAD-ECORISK. The RESRAD-BUILD models were developed and codified by Argonne National Laboratory (ANL); version 1.5 of the code and the user's manual were publicly released in 1994. The original version of the code was written for the Microsoft DOS operating system. However, subsequent versions of the code were written for the Microsoft Windows operating system. The purpose of the present verification task (which includes validation as defined in the standard) is to provide an independent review of the latest version of RESRAD-BUILD under the guidance provided by ANSI/ANS-10.4 for verification and validation of existing computer programs. This approach consists of a posteriori V and V review which takes advantage of available program development products as well as user experience. The purpose, as specified in ANSI/ANS-10.4, is to determine whether the program produces valid responses when used to analyze problems within a specific domain of applications, and to document the level of verification. The culmination of these efforts is the production of this formal Verification Report. The first step in performing the verification of an existing program was the preparation of a Verification Review Plan. The review plan consisted of identifying: Reason(s) why a posteriori verification is to be performed; Scope and objectives for the level of verification selected; Development products to be used for the review; Availability and use of user experience; and Actions to be taken to supplement missing or unavailable development products. The purpose, scope and objectives for the level of verification selected are described in this section of the Verification Report. The development products that were used

WIPP Sampling and Analysis Plan for Solid Waste Management Units and Areas of Concern

International Nuclear Information System (INIS)

2000-01-01

This Sampling and Analysis Plan (SAP) has been prepared to fulfill requirements of Module VII, Section VII.M.2 and Table VII.1, requirement 4 of the Waste Isolation Pilot Plant (WIPP) Hazardous Waste Permit, NM4890139088-TSDF (the Permit); (NMED [New Mexico Environment Department], 1999a). This SAP describes the approach for investigation of the Solid Waste Management Units (SWMU) and Areas of Concern (AOC) specified in the Permit. This SAP addresses the current Permit requirements for a RCRA Facility Investigation(RFI) investigation of SWMUs and AOCs. It uses the results of previous investigations performed at WIPP and expands the investigations as required by the Permit. As an alternative to the RFI specified in Module VII of the Permit, current NMED guidance identifies an Accelerated Corrective Action Approach (ACAA) that may be used for any SWMU or AOC (NMED, 1998). This accelerated approach is used to replace the standard RFI work plan and report sequence with a more flexible decision-making approach. The ACAA process allows a facility to exit the schedule of compliance contained in the facility's Hazardous and Solid Waste Amendments (HSWA) permit module and proceed on an accelerated time frame. Thus, the ACAA process can beentered either before or after a RFI work plan. According to NMED's guidance, a facility can prepare a RFI work plan or SAP for any SWMU or AOC (NMED, 1998).

Development and validation of the interview version of the Hong Kong Chinese WHOQOL-BREF.

Science.gov (United States)

Leung, K F; Wong, W W; Tay, M S M; Chu, M M L; Ng, S S W

2005-06-01

The Hong Kong Chinese version of the WHOQOL-BREF was designed as a self-administered questionnaire and has limitations in clinical application on subjects who have limitations in reading or writing. An interview version is therefore needed to avoid sampling biases in clinical studies. Since there are significant differences in the written Chinese and spoken Cantonese, which is a dialect commonly spoken among people in Hong Kong, and adaptation process for converting the written Chinese into spoken Cantonese was necessary. The interview version was designed to allow administration in both face-to-face interview and telephone interview mode. Three members of the research team translated the formal written Chinese in the self-administered version of the WHOQOL-BREF(HK) into colloquial Cantonese separately. Brief notes extracted from the facet definitions of the WHOQOL-100 were added in brackets after some questions to further explain the intention of the questions. Two series of focus groups were conducted and subsequently the field test version was produced. 329 subjects were recruited by convenient sampling method for the field test. The interview version and the self-administered version was found equivalent. The ICC values of the domain scores ranged from 0.73 in the environment domain to 0.83 in the psychological domain. The face-to-face interview and telephone interview mode of administration were also found equivalent. The ICC for the domain scores ranged from 0.76 in the social interaction domain to 0.84 in the psychological domain. The other psychometric properties of the interview version were found comparable to the self-administered version. The self-administered and the interview version of the WHOQOL-BREF are regarded as identical in group comparison. The authors advise that it is acceptable to use different versions on different subjects in the same study, provided that the same version is applied on the same subject throughout the study.

Optimal sampling plan for clean development mechanism lighting projects with lamp population decay

International Nuclear Information System (INIS)

Ye, Xianming; Xia, Xiaohua; Zhang, Jiangfeng

2014-01-01

Highlights: • A metering cost minimisation model is built with the lamp population decay to optimise CDM lighting projects sampling plan. • The model minimises the total metering cost and optimise the annual sample size during the crediting period. • The required 90/10 criterion sampling accuracy is satisfied for each CDM monitoring report. - Abstract: This paper proposes a metering cost minimisation model that minimises metering cost under the constraints of sampling accuracy requirement for clean development mechanism (CDM) energy efficiency (EE) lighting project. Usually small scale (SSC) CDM EE lighting projects expect a crediting period of 10 years given that the lighting population will decay as time goes by. The SSC CDM sampling guideline requires that the monitored key parameters for the carbon emission reduction quantification must satisfy the sampling accuracy of 90% confidence and 10% precision, known as the 90/10 criterion. For the existing registered CDM lighting projects, sample sizes are either decided by professional judgment or by rule-of-thumb without considering any optimisation. Lighting samples are randomly selected and their energy consumptions are monitored continuously by power meters. In this study, the sampling size determination problem is formulated as a metering cost minimisation model by incorporating a linear lighting decay model as given by the CDM guideline AMS-II.J. The 90/10 criterion is formulated as constraints to the metering cost minimisation problem. Optimal solutions to the problem minimise the metering cost whilst satisfying the 90/10 criterion for each reporting period. The proposed metering cost minimisation model is applicable to other CDM lighting projects with different population decay characteristics as well

Code for plant identification (KKS) key in PC version

International Nuclear Information System (INIS)

Pannenbaecker, K.

1991-01-01

The plant identification system (KKS) as a common development of german plant operators, erection firms and also power plant oriented organisations have decisively influenced the technical-organizing activities of planning and erections as operations and maintenance of all kind of power plants. Fundamentals are three key parts, operation, armatures and function keys. Their management and application is executed by a plantidentification-key code in a PC version, which is briefly described in this report. (orig.) [de

Barriers to Use of Family Planning Methods Among Heterosexual Mexican Couples.

Science.gov (United States)

Arias, María Luisa Flores; Champion, Jane Dimmitt; Soto, Norma Elva Sáenz; Tovar, Marlene; Dávila, Sandra Paloma Esparza

2017-05-01

Family planning has become increasingly important as a fundamental component of sexual health and as such is offered via public health systems worldwide. Identification of barriers to use of family planning methods among heterosexual couples living in Mexico is indicated to facilitate access to family planning methods. Barriers to family planning methods were assessed among Mexican heterosexual, sexually active males and females of reproductive age, using a modified Spanish version of the Barriers to the Use of Family Planning Methods scale (Cronbach's alpha = .89, subscales ranging from .53 to .87). Participants were recruited via convenience sampling in ambulatory care clinics within a metropolitan area in Central Mexico. Participants included 52 heterosexual couples aged 18-35 years (N = 104). Sociodemographic comparisons by gender identified older age and higher education, income, and numbers of sexual partners among men than women. More men (50%) than women (25%) were currently using family planning methods; however, 80% overall indicated intentions for its use. Overall, male condoms were used and intended for use most often by men than women. Significant gender-specific differences were found, with men (71.15%) reporting no family planning barriers, whereas women (55.66%) reported barriers including low socioeconomic status, medical concerns, and stigma. The modified Spanish translation demonstrated usefulness for measuring barriers to family planning methods use in Mexico among heterosexual males and females of reproductive age. Barriers identified by Mexican women in this study may be addressed to reduce potential barriers to family planning among Mexican populations.

Introducing English and German versions of the Adolescent Time Attitude Scale.

Science.gov (United States)

Worrell, Frank C; Mello, Zena R; Buhl, Monika

2013-08-01

In this study, the authors report on the development of English and German versions of the Adolescent Time Attitude Scale (ATAS). The ATAS consists of six subscales assessing Past Positive, Past Negative, Present Positive, Present Negative, Future Positive, and Future Negative time attitudes. The authors describe the development of the scales and present data on the reliability and structural validity of ATAS scores in samples of American (N = 300) and German (N = 316) adolescents. Internal consistency estimates for scores on the English and German versions of the ATAS were in the .70 to .80 range. Confirmatory factor analyses indicated that a six-factor structure yielded the best fit for scores and that the scores were invariant across samples.

Development of a Mobile App for Family Planning Providers.

Science.gov (United States)

Halsall, Viannella; Rogers, Jennifer; Witt, Jacki; Song, Sejun; Nguyen, Hoang Duc Huy; Kelly, Patricia

To provide an overview of lessons learned during the development process of an app for iOS and Android based on national recommendations for providing quality family planning services. After a review of existing apps was conducted to determine whether an app of clinical recommendations for family planning existed, a team of clinicians, training specialists, and app developers created a resource app by first drafting a comprehensive content map. A prototype of the app was then pilot tested using smart tablets by a volunteer convenience sample of women's healthcare professionals. Outcomes measured included usability, acceptability, download analytics, and satisfaction by clinicians as reported through an investigator-developed tool. Sixty-nine professionals tested a prototype of the app, and completed a user satisfaction tool. Overall, user feedback was positive, and a zoom function was added to the final version as a result of the pilot test. Within 3 months of being publicly available, the app was downloaded 677 times, with 97% of downloads occurring on smart phones, 76% downloads occurring on iOS devices, and 24% on Android devices. This trend persisted throughout the following 3 months. Clinicians with an interest in developing an app should consider a team approach to development, pilot test the app prior to wider distribution, and develop a web-based version of the app to be used by clinicians who are unable to access smart devices in their practice setting.

Preliminary site description. Simpevarp area - version 1.1

International Nuclear Information System (INIS)

Winberg, Anders

2004-08-01

resolution. The lithology model includes four interpreted rock domains. The deformation zone model includes 14 zones of interpreted high confidence (of existence). A discrete fracture network model has also been developed where attempts are made to assess effects on fracturing imposed by interpreted deformation zones. Furthermore, the validity of extrapolating surface fracture statistics to larger depths was explored. The rock mechanics strength model is based on information from the Aespoe Hard Rock Laboratory and an empirical, mechanical classification of data from KSH01A and at outcrops. A first model of thermal properties of the rock has been developed largely based on data from Aespoe Hard Rock Laboratory, and projections based on density and mineral content. Overall the rock at Simpevarp is characterised by a low thermal conductivity. A consequence of the planned delay in parts of the geological model is that the hydrogeological description is based solely on the version 0 regional structural model. The regional flow pattern is found to be governed by the geometry of the interpreted deformation zones in relation to the acting hydraulic gradient. Hydrogeological simulations of the groundwater evolution since the last glaciation were compared with the developed hydrogeochemical conceptual model. The conceptual model of the development of post-glacial hydrogeochemistry was updated. Also, the salinity distribution, mixing processes and the major reactions altering the groundwater composition were described down to a depth of 300 m. A first model of the transport properties of the rock was presented, although still rather immature due to lack of site-specific data in support of the model. For the near-surface, the Simpevarp subarea is characterised by a large portion of outcrop rock. There is information regarding the distribution of Quaternary deposits, and some information about the stratigraphy of the till, the latter found to be of small thickness, generally 1-3 m

Field sampling and analysis plan for the remedial investigation of Waste Area Grouping 2 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Boston, H.L.; Ashwood, T.L.; Borders, D.M.; Chidambariah, V.; Downing, D.J.; Fontaine, T.A.; Ketelle, R.H.; Lee, S.Y.; Miller, D.E.; Moore, G.K.; Suter, G.W.; Tardiff, M.F.; Watts, J.A.; Wickliff, D.S.

1992-02-01

This field sampling and analysis (S ampersand A) plan has been developed as part of the Department of Energy's (DOE's) remedial investigation (RI) of Waste Area Grouping (WAG) 2 at Oak Ridge National Laboratory (ORNL) located in Oak Ridge, Tennessee. The S ampersand A plan has been written in support of the remedial investigation (RI) plan for WAG 2 (ORNL 1990). WAG 2 consists of White Oak Creek (WOC) and its tributaries downstream of the ORNL main plant area, White Oak Lake (WOL), White Oak Creek embayment (WOCE) on the Clinch River, and the associated floodplain and subsurface environment (Fig. 1.1). The WOC system is the surface drainage for the major ORNL WAGs and has been exposed to a diversity of contaminants from operations and waste disposal activities in the WOC watershed. WAG 2 acts as a conduit through which hydrologic fluxes carry contaminants from upgradient areas to the Clinch River. Water, sediment, soil, and biota in WAG 2 are contaminated and continue to receive contaminants from upgradient WAGs. This document describes the following: an overview of the RI plan, background information for the WAG 2 system, and objectives of the S ampersand A plan; the scope and implementation of the first 2 years of effort of the S ampersand A plan and includes recent information about contaminants of concern, organization of S ampersand A activities, interactions with other programs, and quality assurance specific to the S ampersand A activities; provides details of the field sampling plans for sediment, surface water, groundwater, and biota, respectively; and describes the sample tracking and records management plan

Intravenous nitroglycerin for external cephalic version: a randomized controlled trial.

Science.gov (United States)

Hilton, Jennifer; Allan, Bruce; Swaby, Cheryl; Wahba, Raouf; Wah, Raouf; Jarrell, John; Wood, Stephen; Ross, Sue; Tran, Quynh

2009-09-01

To estimate whether treatment with intravenous nitroglycerin for uterine relaxation increases the chance of successful external cephalic version. Two double-blind, randomized clinical trials were undertaken: one in nulliparous women and a second in multiparous women. Women presenting for external cephalic version at term were eligible to participate. The primary outcome was immediate success of external cephalic version. Other outcomes were presentation at delivery, cesarean delivery rate, and side effects and complications. Sample size calculations were based on a 100% increase in success of external cephalic version with a one-sided analysis and alpha=0.05 (80% power). In total, 126 women were recruited-82 in the nulliparous trial and 44 in the multiparous trial. Seven patients did not have external cephalic version before delivery but were included in the analysis of success of external cephalic version. One patient was lost to follow-up. The external cephalic version success rate for nulliparous patients was 24% (10 of 42) in patients who received nitroglycerin compared with 8% (3 of 40) in those who receive placebo (P=.04, one-sided Fisher exact test, odds ratio 3.85, lower bound 1.22). In multiparous patients, the external cephalic version success rate did not differ significantly between groups: 44% (10 of 23) in the nitroglycerin group compared with 43% (9 of 21) in the placebo group (P=.60). Treatment with intravenous nitroglycerin increased the rate of successful external cephalic version in nulliparous, but not in multiparous, women. Treatment with intravenous nitroglycerin appeared to be safe, but our numbers were too small to rule out rare serious adverse effects. I.

Routine Radiological Environmental Monitoring Plan. Appendices

International Nuclear Information System (INIS)

Bechtel Nevada

1998-01-01

Supporting material for the plan includes: QUALITY ASSURANCE, ANALYSIS, AND SAMPLING PLAN FOR NTS AIR; QUALITY ASSURANCE, ANALYSIS, AND SAMPLING PLAN FOR WATER ON AND OFF THE NEVADA TEST SITE; QUALITY ASSURANCE, ANALYSIS, AND SAMPLING PLAN FOR NTS BIOTA; QUALITY ASSURANCE, ANALYSIS, AND SAMPLING PLAN FOR DIRECT RADIATION MONITORING; DATA QUALITY OBJECTIVES PROCESS; VADOSE ZONE MONITORING PLAN CHECKLIST

Planning to Improvise? The Role of Reasoning in the Strategy Process: Evidence from Malaysia

OpenAIRE

Hughes, Paul; Hodgkinson, Ian R.; Arshad, Darwina; Hughes, Mathew; Leone, Vitor

2017-01-01

The file attached to this record is the author's final peer reviewed version. The Publisher's final version can be found by following the DOI link. Planning and improvisation are depicted as alternate decision-making orientations in the strategy process literature, executed by two parallel cognitive contexts: rational or intuitive, but can rationality and intuition be harmonised in the strategy process? Strategic managers may not have to choose to either plan or improvise, rather there is ...

Children's Recall of the News: TV News Stories Compared with Three Print Versions.

Science.gov (United States)

van der Molen, Juliette H. Walma; van der Voort, Tom H. A.

1998-01-01

A sample of 144 fourth and sixth graders was presented with five children's news stories, in television form or in one of three print versions. Results indicated that children who watched news on television remembered the stories better than children who read one of the three print versions, regardless of their level of reading proficiency.…

Psychometric Evaluation of the Serbian Version of the Multidimensional Students' Life Satisfaction Scale

Science.gov (United States)

Jovanovic, Veljko; Zuljevic, Dragan

2013-01-01

The main purpose of this study was to evaluate psychometric properties of the Serbian version of the Multidimensional Students' Life Satisfaction Scale (MSLSS). The research was carried out on a sample of 408 high school students (250 females, 158 males), with the mean age 16.6. The Serbian version of the MSLSS has demonstrated good psychometric…

Sampling and analysis plan for sampling of liquid waste streams generated by 222-S Laboratory Complex operations

International Nuclear Information System (INIS)

Benally, A.B.

1997-01-01

This Sampling and Analysis Plan (SAP) establishes the requirements and guidelines to be used by the Waste Management Federal Services of Hanford, Inc. personnel in characterizing liquid waste generated at the 222-S Laboratory Complex. The characterization process to verify the accuracy of process knowledge used for designation and subsequent management of wastes consists of three steps: to prepare the technical rationale and the appendix in accordance with the steps outlined in this SAP; to implement the SAP by sampling and analyzing the requested waste streams; and to compile the report and evaluate the findings to the objectives of this SAP. This SAP applies to portions of the 222-S Laboratory Complex defined as Generator under the Resource Conservation and Recovery Act (RCRA). Any portion of the 222-S Laboratory Complex that is defined or permitted under RCRA as a treatment, storage, or disposal (TSD) facility is excluded from this document. This SAP applies to the liquid waste generated in the 222-S Laboratory Complex. Because the analytical data obtained will be used to manage waste properly, including waste compatibility and waste designation, this SAP will provide directions for obtaining and maintaining the information as required by WAC173-303

Sampling and analysis plan for remediation of Operable Unit 100-IU-3 waste site 600-104. Revision 1

International Nuclear Information System (INIS)

1997-08-01

This sampling and analysis plan presents the rationale and strategy for the sampling and analysis activities to support remediation of 100-IU-3 Operable Unit waste site 600-104. The purpose of the proposed sampling and analysis activities is to demonstrate that time-critical remediation of the waste site for soil containing 2,4-Dichlorophenoxyacetic acid salts and esters (2,4-D) and dioxin/furan isomers at concentrations that exceed cleanup levels has been effective. This shall be accomplished by sampling various locations of the waste site before and after remediation, analyzing the samples, and comparing the results to action levels set by the Washington State Department of Ecology

An Australian Version of the Neighborhood Environment Walkability Scale: Validity Evidence

Science.gov (United States)

Cerin, Ester; Leslie, Eva; Owen, Neville; Bauman, Adrian

2008-01-01

This study examined validity evidence for the Australian version of the Neighborhood Environment Walkability Scale (NEWS-AU). A stratified two-stage cluster sampling design was used to recruit 2,650 adults from Adelaide (Australia). The sample was drawn from residential addresses within eight high-walkable and eight low-walkable suburbs matched…

Portuguese Version of Teacher Feedback Scale: A Preliminary Study

Directory of Open Access Journals (Sweden)

Márcia Laranjeira

2018-06-01

Full Text Available Abstract Teacher feedback in the classroom has a powerful influence on pupils’ performance and motivation. The study aims to analyze psychometric properties of the Portuguese version of the Teacher Feedback Scale (TFS in a sample of 228 children in the 4th grade of schooling. Exploratory factor analysis shows similarities with the original version, and the differences observed were based on the children’s cognitive development characteristics and cultural specificities of the two samples. The relationship between teacher feedback and students’ motivational variables was confirmed, such as the preference that the children expressed for the school subjects. The possibility to make some changes in the items is contemplated, in order to increase validity and reliability of the measure. The data highlight the potential of using the TFS in schools, which could contribute towards clarifying the teachers’ role in the formation of pupils’ self-concept.

Psychometric properties of the Serbian version of the Empathy Quotient (S-EQ

Directory of Open Access Journals (Sweden)

Dimitrijević Aleksandar

2012-01-01

Full Text Available In the present study we examined psychometric properties of the Serbian translation of the Empathy Quotient scale (S-EQ. The translated version of the EQ was applied on a sample of 694 high-school students. A sub-sample consisting of 375 high-school students also completed the Interpersonal Reactivity Index (IRI, another widely used empathy measure. The following statistical analyses were applied: internal consistency analysis, explanatory (EFA and confirmatory (CFA factor analyses, and factor congruence analysis. Correlation with IRI and gender differences were calculated to demonstrate validity of the instrument. Results show that the Serbian 40-item version of EQ has lower reliability (Cronbach’s alpha = .782 than the original. The originally proposed one factor structure of the instrument was not confirmed. The short version with 28 items showed better reliablity (alpha= .807. The three-factor solution (cognitive empathy, emotional reactivity, and social skills showed good cross-sample stability (Tucker congruence coefficient over .8 but the results of CFA confirmed the solution proposed in the reviewed literature only partially. The mean scores are similar to those obtained in the other studies, and, as expected, women have significantly higher scores than men. Correlations with all subscales of IRI are statistically significant for the first two subscales of EQ, but not for the „social skills.” We concluded that the Serbian version of the „Empathy Quotient” is a useful research tool which can contribute to cross-cultural studies of empathy, although its psychometric characteristics are not as good as those obtained in the original study. We also suggest that a 28-item should be used preferably to the original 40-item version. [Projekat Ministarstva nauke Republike Srbije, br. 179018: Identification, measurement and development of cognitive and emotional competences important for a society oriented to European integrations

Predicting intentions not to "drink and drive" using an extended version of the theory of planned behaviour.

Science.gov (United States)

Moan, Inger Synnøve; Rise, Jostein

2011-07-01

The aim of this study was to determine to what extent the theory of planned behaviour (TPB) extended with moral norm and descriptive norm is able to predict intentions not to drink and drive. We also wanted to examine whether different processes guide intentions among young drivers (35 years and below) versus drivers aged above 35 years, and women's versus men's intentions. Questionnaires were sent to a sample of 4000 people in Norway aged between 18 and 70 years, and were completed by 1025 respondents. Analyses were conducted among those who had a driver's licence and who reported drinking at least 1-2 times per year, resulting in a sample of 879 individuals (46.6% were men, 30.3% were 35 years and younger, M=43.9 years). The results showed that the TPB variables explained 10% of the variance in intentions in the sample as a whole, and that the extension variables added 2% to the explained variance after controlling for the impact of the TPB components. Perceived behavioural control was the strongest predictor of intentions (β=0.24, pdrive will be outlined. Copyright © 2011 Elsevier Ltd. All rights reserved.

Phase 2 sampling and analysis plan, Quality Assurance Project Plan, and environmental health and safety plan for the Clinch River Remedial Investigation: An addendum to the Clinch River RCRA Facility Investigation plan

International Nuclear Information System (INIS)

Cook, R.B.; Adams, S.M.; Beauchamp, J.J.; Bevelhimer, M.S.; Blaylock, B.G.; Brandt, C.C.; Etnier, E.L.; Ford, C.J.; Frank, M.L.; Gentry, M.J.; Greeley, M.S.; Halbrook, R.S.; Harris, R.A.; Holladay, S.K.; Hook, L.A.; Howell, P.L.; Kszos, L.A.; Levine, D.A.; Skiles, J.L.; Suter, G.W.

1992-12-01

This document contains a three-part addendum to the Clinch River Resource Conservation and Recovery Act (RCRA) Facility Investigation Plan. The Clinch River RCRA Facility Investigation began in 1989, as part of the comprehensive remediation of facilities on the US Department of Energy Oak Ridge Reservation (ORR). The ORR was added to the National Priorities List in December 1989. The regulatory agencies have encouraged the adoption of Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) terminology; therefore, the Clinch River activity is now referred to as the Clinch River Remedial Investigation (CRRI), not the Clinch River RCRA Facility Investigation. Part 1 of this document is the plan for sampling and analysis (S ampersand A) during Phase 2 of the CRRI. Part 2 is a revision of the Quality Assurance Project Plan for the CRRI, and Part 3 is a revision of the Environmental Health and Safety Plan for the CRRI. The Clinch River RI (CRRI) is designed to address the transport, fate, and distribution of waterborne contaminants (radionuclides, metals, and organic compounds) released from the DOE Oak Ridge Reservation (ORR) and to assess potential risks to human health and the environment associated with these contaminants. Primary areas of investigation are Melton Hill Reservoir, the Clinch River from Melton Hill Dam to its confluence with the Tennessee River, Poplar Creek, and Watts Bar Reservoir. The contaminants identified in the Clinch River/Watts Bar Reservoir (CR/WBR) downstream of the ORR are those associated with the water, suspended particles, deposited sediments, aquatic organisms, and wildlife feeding on aquatic organisms. The purpose of the Phase 2 S ampersand A Plan is to describe the proposed tasks and subtasks developed to meet the primary objectives of the CRRI

Phase 2 sampling and analysis plan, Quality Assurance Project Plan, and environmental health and safety plan for the Clinch River Remedial Investigation: An addendum to the Clinch River RCRA Facility Investigation plan

Energy Technology Data Exchange (ETDEWEB)

Cook, R.B.; Adams, S.M.; Beauchamp, J.J.; Bevelhimer, M.S.; Blaylock, B.G.; Brandt, C.C.; Etnier, E.L.; Ford, C.J.; Frank, M.L.; Gentry, M.J.; Greeley, M.S.; Halbrook, R.S.; Harris, R.A.; Holladay, S.K.; Hook, L.A.; Howell, P.L.; Kszos, L.A.; Levine, D.A.; Skiles, J.L.; Suter, G.W.

1992-12-01

This document contains a three-part addendum to the Clinch River Resource Conservation and Recovery Act (RCRA) Facility Investigation Plan. The Clinch River RCRA Facility Investigation began in 1989, as part of the comprehensive remediation of facilities on the US Department of Energy Oak Ridge Reservation (ORR). The ORR was added to the National Priorities List in December 1989. The regulatory agencies have encouraged the adoption of Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) terminology; therefore, the Clinch River activity is now referred to as the Clinch River Remedial Investigation (CRRI), not the Clinch River RCRA Facility Investigation. Part 1 of this document is the plan for sampling and analysis (S A) during Phase 2 of the CRRI. Part 2 is a revision of the Quality Assurance Project Plan for the CRRI, and Part 3 is a revision of the Environmental Health and Safety Plan for the CRRI. The Clinch River RI (CRRI) is designed to address the transport, fate, and distribution of waterborne contaminants (radionuclides, metals, and organic compounds) released from the DOE Oak Ridge Reservation (ORR) and to assess potential risks to human health and the environment associated with these contaminants. Primary areas of investigation are Melton Hill Reservoir, the Clinch River from Melton Hill Dam to its confluence with the Tennessee River, Poplar Creek, and Watts Bar Reservoir. The contaminants identified in the Clinch River/Watts Bar Reservoir (CR/WBR) downstream of the ORR are those associated with the water, suspended particles, deposited sediments, aquatic organisms, and wildlife feeding on aquatic organisms. The purpose of the Phase 2 S A Plan is to describe the proposed tasks and subtasks developed to meet the primary objectives of the CRRI.

DEMAID - A DESIGN MANAGER'S AID FOR INTELLIGENT DECOMPOSITION (MACINTOSH VERSION)

Science.gov (United States)

Rogers, J. L.

1994-01-01

effects of an output with respect to a change in a particular input. The second method traces backward to determine what modules must be re-executed if the output of a module must be recomputed. DeMAID is available in three machine versions: a Macintosh version which is written in Symantec's Think C 3.01, a Sun version, and an SGI IRIS version, both of which are written in C language. The Macintosh version requires system software 6.0.2 or later and CLIPS 4.3. The source code for the Macintosh version will not compile under version 4.0 of Think C; however, a sample executable is provided on the distribution media. QuickDraw is required for plotting. The Sun version requires GKS 4.1 graphics libraries, OpenWindows 3, and CLIPS 4.3. The SGI IRIS version requires CLIPS 4.3. Since DeMAID is not compatible with CLIPS 5.0 or later, the source code for CLIPS 4.3 is included on the distribution media; however, the documentation for CLIPS 4.3 is not included in the documentation package for DeMAID. It is available from COSMIC separately as the documentation for MSC-21208. The standard distribution medium for the Macintosh version of DeMAID is a set of four 3.5 inch 800K Macintosh format diskettes. The standard distribution medium for the Sun version of DeMAID is a .25 inch streaming magnetic tape cartridge (QIC-24) in UNIX tar format. The standard distribution medium for the IRIS version is a .25 inch IRIX compatible streaming magnetic tape cartridge in UNIX tar format. All versions include sample input. DeMAID was originally developed for use on VAX VMS computers in 1989. The Macintosh version of DeMAID was released in 1991 and updated in 1992. The Sun version of DeMAID was released in 1992 and updated in 1993. The SGI IRIS version was released in 1993.

DEMAID - A DESIGN MANAGER'S AID FOR INTELLIGENT DECOMPOSITION (SUN VERSION)

Science.gov (United States)

Rogers, J. L.

1994-01-01

effects of an output with respect to a change in a particular input. The second method traces backward to determine what modules must be re-executed if the output of a module must be recomputed. DeMAID is available in three machine versions: a Macintosh version which is written in Symantec's Think C 3.01, a Sun version, and an SGI IRIS version, both of which are written in C language. The Macintosh version requires system software 6.0.2 or later and CLIPS 4.3. The source code for the Macintosh version will not compile under version 4.0 of Think C; however, a sample executable is provided on the distribution media. QuickDraw is required for plotting. The Sun version requires GKS 4.1 graphics libraries, OpenWindows 3, and CLIPS 4.3. The SGI IRIS version requires CLIPS 4.3. Since DeMAID is not compatible with CLIPS 5.0 or later, the source code for CLIPS 4.3 is included on the distribution media; however, the documentation for CLIPS 4.3 is not included in the documentation package for DeMAID. It is available from COSMIC separately as the documentation for MSC-21208. The standard distribution medium for the Macintosh version of DeMAID is a set of four 3.5 inch 800K Macintosh format diskettes. The standard distribution medium for the Sun version of DeMAID is a .25 inch streaming magnetic tape cartridge (QIC-24) in UNIX tar format. The standard distribution medium for the IRIS version is a .25 inch IRIX compatible streaming magnetic tape cartridge in UNIX tar format. All versions include sample input. DeMAID was originally developed for use on VAX VMS computers in 1989. The Macintosh version of DeMAID was released in 1991 and updated in 1992. The Sun version of DeMAID was released in 1992 and updated in 1993. The SGI IRIS version was released in 1993.

WIPP Sampling and Analysis Plan for Solid Waste Management Units and Areas of Concern

Energy Technology Data Exchange (ETDEWEB)

None, None

2000-05-23

This Sampling and Analysis Plan (SAP) has been prepared to fulfill requirements of Module VII, Section VII.M.2 and Table VII.1, requirement 4 of the Waste Isolation Pilot Plant (WIPP) Hazardous Waste Permit, NM4890139088-TSDF (the Permit); (NMED [New Mexico Environment Department], 1999a). This SAP describes the approach for investigation of the Solid Waste Management Units (SWMU) and Areas of Concern (AOC) specified in the Permit. This SAP addresses the current Permit requirements for a RCRA Facility Investigation(RFI) investigation of SWMUs and AOCs. It uses the results of previous investigations performed at WIPP and expands the investigations as required by the Permit. As an alternative to the RFI specified in Module VII of the Permit, current NMED guidance identifies an Accelerated Corrective Action Approach (ACAA) that may be used for any SWMU or AOC (NMED, 1998). This accelerated approach is used to replace the standard RFI work plan and report sequence with a more flexible decision-making approach. The ACAA process allows a facility to exit the schedule of compliance contained in the facility's Hazardous and Solid Waste Amendments (HSWA) permit module and proceed on an accelerated time frame. Thus, the ACAA process can beentered either before or after a RFI work plan. According to NMED's guidance, a facility can prepare a RFI work plan or SAP for any SWMU or AOC (NMED, 1998).

TRANSLATION, VALIDATION AND PSYCHOMETRIC EVALUATION OF PROBLEM AREAS IN DIABETES QUESTIONNAIRE: THE URDU VERSION

OpenAIRE

Sajjad Haider, Marvi Baloch, Qaiser Iqbal and Fahad Saleem

2017-01-01

Objective: The study aims to translate and examine the psychometric properties of the Urdu version of Problem Areas in Diabetes (PAID) questionnaire among Type 2 diabetic patients (T2DM) in Quetta, Pakistan. Method: A standard ‘‘forward–backward’’ procedure of translation was used to translate the English version of PAID into Urdu (official language of Pakistan). The translated version was then validated on a convenience sample of 120 T2DM patients attending a public hospital in Quetta, Pakis...

Site characterization summary report for dry weather surface water sampling upper East Fork Poplar Creek characterization area Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-08-01

This report describes activities associated with conducting dry weather surface water sampling of Upper East Fork Poplar Creek (UEFPC) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. This activity is a portion of the work to be performed at UEFPC Operable Unit (OU) 1 [now known as the UEFPC Characterization Area (CA)], as described in the RCRA Facility Investigation Plan for Group 4 at the Oak- Ridge Y-12 Plant, Oak Ridge, Tennessee and in the Response to Comments and Recommendations on RCRA Facility Investigation Plan for Group 4 at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee, Volume 1, Operable Unit 1. Because these documents contained sensitive information, they were labeled as unclassified controlled nuclear information and as such are not readily available for public review. To address this issue the U.S. Department of Energy (DOE) published an unclassified, nonsensitive version of the initial plan, text and appendixes, of this Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) Plan in early 1994. These documents describe a program for collecting four rounds of wet weather and dry weather surface water samples and one round of sediment samples from UEFPC. They provide the strategy for the overall sample collection program including dry weather sampling, wet weather sampling, and sediment sampling. Figure 1.1 is a schematic flowchart of the overall sampling strategy and other associated activities. A Quality Assurance Project Plan (QAPJP) was prepared to specifically address four rounds of dry weather surface water sampling and one round of sediment sampling. For a variety of reasons, sediment sampling has not been conducted and has been deferred to the UEFPC CA Remedial Investigation (RI), as has wet weather sampling.

Rulison Monitoring Plan

Energy Technology Data Exchange (ETDEWEB)

None

2010-07-01

The Project Rulison Monitoring Plan has been developed as part of the U.S. Department of Energy (DOE) Office of Legacy Management's mission to protect human health and the environment. The purpose of the plan is to monitor fluids from gas wells for radionuclides that would indicate contamination is migrating from the Rulison detonation zone to producing gas wells, allowing action to be taken before the contamination could pose a risk. The Monitoring Plan (1) lists the contaminants present and identifies those that have the greatest potential to migrate from the detonation zone (radionuclide source term), (2) identifies locations that monitor the most likely transport pathways, (3) identifies which fluids will be sampled (gas and liquid) and why, (4) establishes the frequency of sampling, and (5) specifies the most practical analyses and where the analysis results will be reported. The plan does not affect the long-term hydrologic sampling conducted by DOE since 1972, which will continue for the purpose of sampling shallow groundwater and surface water near the site. The Monitoring Plan was developed in anticipation of gas wells being drilled progressively nearer the Rulison site. DOE sampled 10 gas wells in 1997 and 2005 at distances ranging from 2.7 to 7.6 miles from the site to establish background concentrations for radionuclides. In a separate effort, gas industry operators and the Colorado Oil and Gas Conservation Commission (COGCC) developed an industry sampling and analysis plan that was implemented in 2007. The industry plan requires the sampling of gas wells within 3 miles of the site, with increased requirements for wells within 1 mile of the site. The DOE plan emphasizes the sampling of wells near the site (Figure 1), specifically those with a bottom-hole location of 1 mile or less from the detonation, depending on the direction relative to the natural fracture trend of the producing formation. Studies indicate that even the most mobile

Hanford Sampling Quality Management Plan (HSQMP)

International Nuclear Information System (INIS)

Hyatt, J.E.

1995-06-01

HSQMP establishes quality requirements in response to DOE Order 5700. 6C and to 10 Code of Federal Regulations 830.120. HSQMP is designed to meet the needs of Richland Operations Office for controlling the quality of services provided by sampling operations. It is issued through the Analytical Services Program of the Waste Programs Division. This document describes the Environmental Sampling and Analysis Program activities considered to represent the best management activities necessary to achieve a sampling program with adequate control

The Reasons for Living Scale-Military Version: Assessing Protective Factors Against Suicide in a Military Sample.

Science.gov (United States)

Deutsch, Anne-Marie; Lande, R Gregory

2017-07-01

Military suicide rates have been rising over the past decade and continue to challenge military treatment facilities. Assessing suicide risk and improving treatments are a large part of the mission for clinicians who work with uniformed service members. This study attempts to expand the toolkit of military suicide prevention by focusing on protective factors over risk factors. In 1983, Marsha Linehan published a checklist called the Reasons for Living Scale, which asked subjects to check the reasons they choose to continue living, rather than choosing suicide. The authors of this article hypothesized that military service members may have different or additional reasons to live which may relate to their military service. They created a new version of Linehan's inventory by adding protective factors related to military life. The purpose of these additions was to make the inventory more acceptable and relevant to the military population, as well as to identify whether these items constitute a separate subscale as distinguished from previously identified factors. A commonly used assessment tool, the Reasons for Living Inventory (RFL) designed by Marsha Linehan, was expanded to offer items geared to the military population. The RFL presents users with a list of items which may be reasons to not commit suicide (e.g., "I have a responsibility and commitment to my family"). The authors used focus groups of staff and patients in a military psychiatric partial hospitalization program to identify military-centric reasons to live. This process yielded 20 distinct items which were added to Linehan's original list of 48. This expanded list became the Reasons for Living-Military Version. A sample of 200 patients in the military partial hospitalization program completed the inventory at time of or close to admission. This study was approved by the Institutional Review Board at Walter Reed National Military Center for adhering to ethical principles related to pursuing research

Volumetric Modulated Arc Therapy (VMAT) Treatment Planning for Superficial Tumors

International Nuclear Information System (INIS)

Zacarias, Albert S.; Brown, Mellonie F.; Mills, Michael D.

2010-01-01

The physician's planning objective is often a uniform dose distribution throughout the planning target volume (PTV), including superficial PTVs on or near the surface of a patient's body. Varian's Eclipse treatment planning system uses a progressive resolution optimizer (PRO), version 8.2.23, for RapidArc dynamic multileaf collimator volumetric modulated arc therapy planning. Because the PRO is a fast optimizer, optimization convergence errors (OCEs) produce dose nonuniformity in the superficial area of the PTV. We present a postsurgical cranial case demonstrating the recursive method our clinic uses to produce RapidArc treatment plans. The initial RapidArc treatment plan generated using one 360 o arc resulted in substantial dose nonuniformity in the superficial section of the PTV. We demonstrate the use of multiple arcs to produce improved dose uniformity in this region. We also compare the results of this superficial dose compensation method to the results of a recursive method of dose correction that we developed in-house to correct optimization convergence errors in static intensity-modulated radiation therapy treatment plans. The results show that up to 4 arcs may be necessary to provide uniform dose to the surface of the PTV with the current version of the PRO.

Preliminary site description Forsmark area - version 1.1

International Nuclear Information System (INIS)

2004-03-01

, mechanical classification by depth at KFM01A and at outcrops. A first model of thermal properties of the rock has been developed, although still rather immature due to few site-specific data in support of the model. The hydrogeological description is based on the new geological (structure) model and the fracture transmissivity distribution of the DFN model is based on the data from depth (cored borehole KFM01A). The fracture intensity and permeability are very low below 400 m depth. Hydrogeological simulations of the groundwater evolution since the last glaciation have been performed and compared with the hydrogeochemical conceptual model. The conceptual model of the development of post-glacial hydro geochemistry has been updated. Also, the salinity distribution, mixing processes and the major reactions altering the groundwaters have been described down to a depth of 200 m. A first model of the transport properties of the rock has been presented, although still rather immature due to lack of site-specific data in support of the model. For the near-surface, there is additional information regarding the stratigraphic distribution of glacial till and water-laid sediment, with related updates in the description. There is much uncertainty in version 1.1 of the site descriptive model, but the main uncertainties have been identified, some are also quantified and others are left as input to alternative hypotheses. However, since a main reason for uncertainty in version 1.1 is lack of data and poor data density and as much more data are expected in coming data freezes, it has not been judged meaningful to carry the uncertainty quantification or the alternative model generation too far. Advances have been made on some of the important site specific questions that were formulated in planning the execution programme for the Forsmark area. Concerning the shape of the tectonic lens, the understanding of the three dimensional shape of the rock domains in the local model area is now fair

Underground Test Area Project Waste Management Plan (Rev. No. 2, April 2002)

International Nuclear Information System (INIS)

IT Corporation, Las Vegas

2002-01-01

The U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Operations Office (NNSA/NV) initiated the UGTA Project to characterize the risk posed to human health and the environment as a result of underground nuclear testing activities at the Nevada Test Site (NTS). The UGTA Project investigation sites have been grouped into Corrective Action Units (CAUs) in accordance with the most recent version of the Federal Facility Agreement and Consent Order. The primary UGTA objective is to gather data to characterize the groundwater aquifers beneath the NTS and adjacent lands. The investigations proposed under the UGTA program may involve the drilling and sampling of new wells; recompletion, monitoring, and sampling of existing wells; well development and hydrologic/ aquifer testing; geophysical surveys; and subsidence crater recharge evaluation. Those wastes generated as a result of these activities will be managed in accordance with existing federal and state regulations, DOE Orders, and NNSA/NV waste minimization and pollution prevention objectives. This Waste Management Plan provides a general framework for all Underground Test Area (UGTA) Project participants to follow for the characterization, storage/accumulation, treatment, and disposal of wastes generated by UGTA Project activities. The objective of this waste management plan is to provide guidelines to minimize waste generation and to properly manage wastes that are produced. Attachment 1 to this plan is the Fluid Management Plan and details specific strategies for management of fluids produced under UGTA operations

Protocol for collecting eDNA samples from streams [Version 2.3

Science.gov (United States)

K. J. Carim; T. Wilcox; M. K. Young; K. S. McKelvey; M. K. Schwartz

2015-01-01

Throughout the 2014 field season, we had over two dozen biologist throughout the western US collect over 300 samples for eDNA analysis with paired controls. Control samples were collected by filtering 0.5 L of distilled water. No samples had any evidence of field contamination. This method of sampling verifies the cleanliness of the field equipment, as well as the...

Engineering task plan for development, fabrication, and deployment of nested, fixed depth fluidic sampling and at-tank analysis systems

International Nuclear Information System (INIS)

REICH, F.R.

1999-01-01

An engineering task plan was developed that presents the resources, responsibilities, and schedules for the development, test, and deployment of the nested, fixed-depth fluidic sampling and at-tank analysis system. The sampling system, deployed in the privatization contract double-shell tank feed tank, will provide waste samples for assuring the readiness of the tank for shipment to the privatization contractor for vitrification. The at-tank analysis system will provide ''real-time'' assessments of the sampled wastes' chemical and physical properties. These systems support the Hanford Phase 1B Privatization Contract

LLNL Yucca Mountain project - near-field environment characterization technical area: Letter report: EQ3/6 version 8: differences from version 7

Energy Technology Data Exchange (ETDEWEB)

Wolery, T.J.

1994-09-29

EQ3/6 is a software package for geochemical modeling of aqueous systems, such as water/rock or waste/water rock. It is being developed for a variety of applications in geochemical studies for the Yucca Mountain Site Characterization Project. The software has been extensively rewritten for Version 8. The source code has been extensively modernized. The software is now written in Fortran 77 with the most common extensions that are part of the new Fortran 90 standard. The architecture of the software has been improved for better performance and to allow the incorporation of new functional capabilities in Version 8 and planned subsequent versions. In particular, the structure of the major data arrays has been significantly altered and extended. Three new major functional capabilities have been incorporated in Version 8. The first of these allows the treatment of redox disequilibrium in reaction-path modeling. This is a natural extension of the long-running capability of providing for such disequilibrium in static speciation-solubility calculations. Such a capability is important, for example, when dealing with systems containing organic species and certain dissolved gas species. The user defines (and sets the controls for) the components in disequilibrium. Such corrections can now be made if the requisite data are present on a supporting data file. At present, this capability is supported only by the SHV data file, which is based on SUPCRT92. Equilibrium constants and other thermodynamic quantities are correct1961ed for pressures which lie off a standard curve, which is defined on the supporting data file and ordinarily corresponds to 1.013 bar up to IOOC, and the steam/liquid water equilibrium pressure up to 300C. The third new major capability is generic ion exchange option previously developed in prototype in a branch Version 7 level version of EQ3/6 by Brian Viani, Bill Bourcier, and Carol Bruton. This option has been modified to fit into the Version 8 data

Phase 2 Sampling Plan for Chestnut Ridge Operable Unit 2 (Filled Coal Ash Pond/Upper McCoy Branch) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1993-01-01

CDM Federal Programs Corporation (CDM Federal) was contracted by Energy Systems to prepare a Phase II Sampling Plan to describe the field investigation work necessary to address regulatory agency review comments on the Remedial Investigation of the Filled Coal Ash Pond (FCAP)/Upper McCoy Branch, Chestnut Ridge Operable Unit 2 at the Y-12 Plant, conducted by CH2M Hill in 1990. The scope and approach of the field investigation described in this plan specifically focus on deficiencies noted by the regulators in discussions at the comment resolution meeting of May 8, 1992, in Oak Ridge, Tennessee. This Phase II Sampling Plan includes a field sampling plan, a field and laboratory quality assurance project plan, a health and safety plan, a waste management plan, and appendixes providing an update to the applicable or relevant and appropriate requirements for this site and field and laboratory testing methods and procedures

Theory of planned behavior and knowledge sharing among nurses in patient computer management system: The role of distributive justice

Directory of Open Access Journals (Sweden)

Sarminah Samad

2018-05-01

Full Text Available This study examined the relationship between Theory of Planned Behavior and knowledge sharing among nurses in Patient Computer Management System. Consequently, it determined the moderating effect of distributive justice on the relationship between Theory Planned Behavior and knowledge sharing. A quantitative approach was employed in this study. The research was based on a correlational and cross-sectional study which involved a total of 336 nurses. Data was collected based on random sampling via self-administered questionnaires. Partial Least Squares (PLS (Version 3.0 analysis was used to analyze the data. The study revealed that Theory of Plan Behavior components were significantly related to knowledge sharing. These components were also found to have a significant and positive influence on knowledge sharing. The study revealed that distributive justice had significantly moderated the relationship between two components of Theory Planned Behavior (attitude and subjective norm and knowledge sharing.

Assessing Reliability of Two Versions of Vocabulary Levels Tests in Iranian Context

Directory of Open Access Journals (Sweden)

Aso Bayazidi

2017-02-01

Full Text Available This study examined the equivalence and reliability of the two versions of the Vocabulary Levels Test in an Iranian context. This study was motivated by the fact that the Vocabulary Levels test is increasingly being used in Iran for both research and pedagogical purposes without having been checked for validity and reliability in this context. The equivalence and reliability of the two versions of the test were examined through the parallel-form approach to reliability in Classical True Score theory. Seventy-five intermediate learners of English as a foreign language at the Iran Language Institute took the two versions of the test with one week interval between the two administrations in a counterbalanced fashion. To examine the equivalence of the two versions, the means and variances of the scores obtained for the two tests were compared using paired-sample t-test and one-way ANOVA, respectively. The results of the analyses indicated that the difference between the means of the two versions was significant, and the two versions cannot be considered as parallel forms. To assess the reliability of the two versions, the correlation between the scores obtained from them was estimated using Pearson Product Moment correlation. The results of the analyses showed that the two versions are highly correlated and are reliable tests. It is concluded that the two versions should not be treated as equivalent in longitudinal and gain score studies.

Field Sampling Plan for the Operable Units 6-05 and 10-04 Remedial Action, Phase IV

Energy Technology Data Exchange (ETDEWEB)

R. Wells

2006-11-14

This Field Sampling Plan outlines the collection and analysis of samples in support of Phase IV of the Waste Area Group 10, Operable Units 6-05 and 10-04 remedial action. Phase IV addresses the remedial actions to areas with the potential for unexploded ordnance at the Idaho National Laboratory Site. These areas include portions of the Naval Proving Ground, the Arco High-Altitude Bombing Range, and the Twin Buttes Bombing Range. The remedial action consists of removal and disposal of ordnance by high-order detonation, followed by sampling to determine the extent, if any, of soil that might have been contaminated by the detonation activities associated with the disposal of ordnance during the Phase IV activities and explosives during the Phase II activities.

Preliminary site description. Simpevarp area - version 1.1

Energy Technology Data Exchange (ETDEWEB)

Winberg, Anders [ed.

2004-08-01

resolution. The lithology model includes four interpreted rock domains. The deformation zone model includes 14 zones of interpreted high confidence (of existence). A discrete fracture network model has also been developed where attempts are made to assess effects on fracturing imposed by interpreted deformation zones. Furthermore, the validity of extrapolating surface fracture statistics to larger depths was explored. The rock mechanics strength model is based on information from the Aespoe Hard Rock Laboratory and an empirical, mechanical classification of data from KSH01A and at outcrops. A first model of thermal properties of the rock has been developed largely based on data from Aespoe Hard Rock Laboratory, and projections based on density and mineral content. Overall the rock at Simpevarp is characterised by a low thermal conductivity. A consequence of the planned delay in parts of the geological model is that the hydrogeological description is based solely on the version 0 regional structural model. The regional flow pattern is found to be governed by the geometry of the interpreted deformation zones in relation to the acting hydraulic gradient. Hydrogeological simulations of the groundwater evolution since the last glaciation were compared with the developed hydrogeochemical conceptual model. The conceptual model of the development of post-glacial hydrogeochemistry was updated. Also, the salinity distribution, mixing processes and the major reactions altering the groundwater composition were described down to a depth of 300 m. A first model of the transport properties of the rock was presented, although still rather immature due to lack of site-specific data in support of the model. For the near-surface, the Simpevarp subarea is characterised by a large portion of outcrop rock. There is information regarding the distribution of Quaternary deposits, and some information about the stratigraphy of the till, the latter found to be of small thickness, generally 1-3 m

Chinese version of Impact of Weight on Quality of Life for Kids: psychometric properties in a large school-based sample.

Science.gov (United States)

He, Jinbo; Zhu, Hong; Luo, Xingwei; Cai, Taisheng; Wu, Siyao; Lu, Yao

2016-06-01

The Impact of Weight on Quality of Life for Kids (IWQOL-Kids) is the first self-report questionnaire for assessing weight-related quality of life for youth. However, there is no Chinese version of IWQOL-Kids. Thus, the objective of this research was to translate IWQOL-Kids into Mandarin and evaluate its psychometric properties in a large school-based sample. The total sample included 2282 participants aged 11-18 years old, including 1703 non-overweight, 386 overweight and 193 obese students. IWQOL-Kids was translated and culturally adapted by following the international guidelines for instrument linguistic validation procedures. The psychometric evaluation included internal consistency, test-retest reliability, exploratory factor analysis (EFA), confirmatory factor analysis (CFA), convergent validity and discriminant validity. Cronbach's α for the Chinese version of IWQOL-Kids (IWQOL-Kids-C) was 0.956 and ranged from 0.891 to 0.927 for subscales. IWQOL-Kids-C showed a test-retest coefficient of 0.937 after 2 weeks and ranged from 0.847 to 0.903 for subscales. The original four-factor model was reproduced by EFA after seven iterations, accounting for 69.28% of the total variance. CFA demonstrated that the four-factor model had good fit indices with comparative fit index = 0.92, normed fit index = 0.91, goodness of fit index = 0.86, root mean square error of approximation = 0.07 and root mean square residual = 0.03. Convergent validity and discriminant validity were demonstrated with higher correlations between similar constructs and lower correlations between dissimilar constructs of IWQOL-Kids-C and PedsQL™ 4.0. The significant differences were found across the body mass index groups, and IWQOL-Kids-C had higher effect sizes than PedsQL™4.0 when comparing non-overweight and obese groups, supporting the sensitivity of IWQOL-Kids-C. IWQOL-Kids-C is a satisfactory, valid and reliable instrument to assess weight-related quality of life for Chinese children and

Groundwater level monitoring sampling and analysis plan for the environmental monitoring plan at waste area grouping 6, Oak Ridge National Laboratory, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This document is the Groundwater Level Monitoring Sampling and Analysis Plan (SAP) for Waste Area Grouping (WAG) 6 at Oak Ridge National Laboratory (ORNL). Note that this document is referred to as a SAP even though no sampling and analysis will be conducted. The term SAP is used for consistency. The procedures described herein are part of the Environmental Monitoring Plan (EMP) for WAG 6, which also includes monitoring tasks for seeps and springs, groundwater quality, surface water, and meteorological parameters. Separate SAPs are being issued concurrently to describe each of these monitoring programs. This SAP has been written for the use of the field personnel responsible for implementation of the EMP, with the intent that the field personnel will be able to take these documents to the field and quickly find the appropriate steps required to complete a specific task. In many cases, Field Operations Procedures (FOPs) will define the steps required for an activity. The FOPs for the EMP are referenced and briefly described in the relevant sections of the SAPs, and are contained within the FOP Manual. Both these documents (the SAP and the FOP Manual) will be available to personnel in the field.

Groundwater level monitoring sampling and analysis plan for the environmental monitoring plan at waste area grouping 6, Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1995-09-01

This document is the Groundwater Level Monitoring Sampling and Analysis Plan (SAP) for Waste Area Grouping (WAG) 6 at Oak Ridge National Laboratory (ORNL). Note that this document is referred to as a SAP even though no sampling and analysis will be conducted. The term SAP is used for consistency. The procedures described herein are part of the Environmental Monitoring Plan (EMP) for WAG 6, which also includes monitoring tasks for seeps and springs, groundwater quality, surface water, and meteorological parameters. Separate SAPs are being issued concurrently to describe each of these monitoring programs. This SAP has been written for the use of the field personnel responsible for implementation of the EMP, with the intent that the field personnel will be able to take these documents to the field and quickly find the appropriate steps required to complete a specific task. In many cases, Field Operations Procedures (FOPs) will define the steps required for an activity. The FOPs for the EMP are referenced and briefly described in the relevant sections of the SAPs, and are contained within the FOP Manual. Both these documents (the SAP and the FOP Manual) will be available to personnel in the field

Measurement of radioactivity in the environment - Soil - Part 2: Guidance for the selection of the sampling strategy, sampling and pre-treatment of samples

International Nuclear Information System (INIS)

2007-01-01

This part of ISO 18589 specifies the general requirements, based on ISO 11074 and ISO/IEC 17025, for all steps in the planning (desk study and area reconnaissance) of the sampling and the preparation of samples for testing. It includes the selection of the sampling strategy, the outline of the sampling plan, the presentation of general sampling methods and equipment, as well as the methodology of the pre-treatment of samples adapted to the measurements of the activity of radionuclides in soil. This part of ISO 18589 is addressed to the people responsible for determining the radioactivity present in soil for the purpose of radiation protection. It is applicable to soil from gardens, farmland, urban or industrial sites, as well as soil not affected by human activities. This part of ISO 18589 is applicable to all laboratories regardless of the number of personnel or the range of the testing performed. When a laboratory does not undertake one or more of the activities covered by this part of ISO 18589, such as planning, sampling or testing, the corresponding requirements do not apply. Information is provided on scope, normative references, terms and definitions and symbols, principle, sampling strategy, sampling plan, sampling process, pre-treatment of samples and recorded information. Five annexes inform about selection of the sampling strategy according to the objectives and the radiological characterization of the site and sampling areas, diagram of the evolution of the sample characteristics from the sampling site to the laboratory, example of sampling plan for a site divided in three sampling areas, example of a sampling record for a single/composite sample and example for a sample record for a soil profile with soil description. A bibliography is provided

Sandia National Laboratories Advanced Simulation and Computing (ASC) software quality plan. Part 1 : ASC software quality engineering practices version 1.0.

Energy Technology Data Exchange (ETDEWEB)

Minana, Molly A.; Sturtevant, Judith E.; Heaphy, Robert; Hodges, Ann Louise; Boucheron, Edward A.; Drake, Richard Roy; Forsythe, Christi A.; Schofield, Joseph Richard, Jr.; Pavlakos, Constantine James; Williamson, Charles Michael; Edwards, Harold Carter

2005-01-01

The purpose of the Sandia National Laboratories (SNL) Advanced Simulation and Computing (ASC) Software Quality Plan is to clearly identify the practices that are the basis for continually improving the quality of ASC software products. Quality is defined in DOE/AL Quality Criteria (QC-1) as conformance to customer requirements and expectations. This quality plan defines the ASC program software quality practices and provides mappings of these practices to the SNL Corporate Process Requirements (CPR 1.3.2 and CPR 1.3.6) and the Department of Energy (DOE) document, ASCI Software Quality Engineering: Goals, Principles, and Guidelines (GP&G). This quality plan identifies ASC management and software project teams' responsibilities for cost-effective software engineering quality practices. The SNL ASC Software Quality Plan establishes the signatories commitment to improving software products by applying cost-effective software engineering quality practices. This document explains the project teams opportunities for tailoring and implementing the practices; enumerates the practices that compose the development of SNL ASC's software products; and includes a sample assessment checklist that was developed based upon the practices in this document.

Initial analysis and curation plans for MUSES-C asteroidal samples

Science.gov (United States)

Yano, H.; Kushiro, I.; Fujiwara, A.

that there are a few more areas of expertise still lacked within the recommended members. Thus, the competition shall be repeated one or two more times (in early 2003 after the launch, and possibly in 2005 after in-situ data is obtained) in order to collect the best Japanese experts in the whole range of different types of analyses at the time of the sample return. The final members of the MASPET will be appointed about 2 years prior to the Earth return. Then they will conduct a Stest runT of the whole initial analysis procedures at the ISAS asteromaterial curation facility, to be newly created in next a few years, and their respective analysis facilities. This talk also covers the current concepts of the facility and plans of analysis procedure flow.

Preliminary Validation of a Brazilian Version of the Sport Motivation Scale

Directory of Open Access Journals (Sweden)

Mauricio Bara Filho

2011-05-01

Full Text Available The Sport Motivation Scale was firstly developed in French and later translated into English and validated by Pelletier et al. (1995. It is based on the principles of self-determination theory. The present study translated the English version into Portuguese to access and validate it with Brazilian athletes using a sample of 419 athletes (127 women and 292 men from ten sports. The Brazilian version of the scale showed satisfactory levels of internal consistency and temporal stability over a four-week period. The results of a confirmatory factor analysis partially supported the seven-factor structure. Finally, gender differences were found in all subscales. Taken together, these findings support the use of the Brazilian version of the scale for the assessment of motivation in sport.

Sampling Based Trajectory Planning for Robots in Dynamic Human Environments

DEFF Research Database (Denmark)

Svenstrup, Mikael

2010-01-01

Open-ended human environments, such as pedestrian streets, hospital corridors, train stations etc., are places where robots start to emerge. Hence, being able to plan safe and natural trajectories in these dynamic environments is an important skill for future generations of robots. In this work...... the problem is formulated as planning a minimal cost trajectory through a potential field, defined from the perceived position and motion of persons in the environment. A modified Rapidlyexploring Random Tree (RRT) algorithm is proposed as a solution to the planning problem. The algorithm implements a new...... for the uncertainty in the dynamic environment. The planning algorithm is demonstrated in a simulated pedestrian street environment....

A therapist version of the Alliance Negotiation Scale.

Science.gov (United States)

Doran, Jennifer M; Gómez-Penedo, Juan Martín; Safran, Jeremy D; Roussos, Andrés

2018-05-02

The aim of the current study was to design and evaluate a therapist version of the Alliance Negotiation Scale (ANS). The ANS was created in order to operationalize the construct of dyadic negotiation in psychotherapy and to augment existing conceptualizations of the working alliance. The ANS has existed only as a client self-report form since its inception and has demonstrated promise as a psychotherapy process measure. This research intended to develop a complementary therapist self-report version of the measure. The scale creation process is discussed in detail, and the results of a preliminary psychometric investigation are reported. The ANS-Therapist version (ANS-T) was developed using a sample of therapists (n = 114) through a principal components analysis procedure. The ANS-T contains 9 unidimensional items and was moderately correlated with therapist-reported working alliance (r = .468). The results of the study support the composition of the ANS-T and provide initial support for the reliability and validity of the measure. Copyright © 2018 John Wiley & Sons, Ltd.

Development of a Maltese version of oral health-associated questionnaires: OHIP-14, GOHAI, and the Denture Satisfaction Questionnaire.

Science.gov (United States)

Santucci, Daniela; Camilleri, Liberato; Kobayashi, Yasuyoshi; Attard, Nikolai

2014-01-01

To show the reliability of the Maltese translations of OHIP-14, GOHAI, and the Denture Satisfaction Questionnaire, define the reliability of the responses, and determine the correlation between OHIP-14 and GOHAI. The items of the three questionnaires (OHIP-14, GOHAI, and Denture Satisfaction) were translated into Maltese and back into English to compare with the original version. Specific sampling of a population well versed in Maltese and English was carried out to obtain a sample of respondents for each questionnaire. Data were gathered through self-administered questionnaires: first administering the Maltese version and following with the English version 1 week later. Participation rates were high (98%). Cronbach's alpha for all three questionnaires was high (> 0.7), indicating satisfactory test-retest reliability of the instruments. Similarly, the Spearman correlation coefficients for both the English and Maltese versions of OHIP-14 and GOHAI were good (> 0.6). The Maltese versions of OHIP-14, GOHAI, and the Denture Satisfaction Questionnaire can be safely used as a valid alternative to the English versions in studies of patients who are limited in linguistic proficiency.

Sampling and analysis plan for the preoperational environmental survey for the immobilized low activity waste (ILAW) project W-465

International Nuclear Information System (INIS)

Mitchell, R.M.

1998-01-01

This document provides a detailed description of the Sampling and Analysis Plan for the Preoperational Survey to be conducted at the Immobilized Low Activity Waste (ILAW) Project Site in the 200 East Area

Comparisons of ANSI standards cited in the NRC standard review plan, NUREG-0800 and related documents

International Nuclear Information System (INIS)

Ankrum, A.R.; Bohlander, K.L.; Gilbert, E.R.; Pawlowski, R.A.; Spiesman, J.B.

1995-11-01

This report provides the results of comparisons of the cited and latest versions of ANSI standards cited in the NRC Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants (NUREG 0800) and related documents. The comparisons were performed by Battelle Pacific Northwest Laboratories in support of the NRC's Standard Review Plan Update and Development Program. Significant changes to the standards, from the cited version to the latest version, are described and discussed in a tabular format for each standard. Recommendations for updating each citation in the Standard Review Plan are presented. Technical considerations and suggested changes are included for related regulatory documents (i.e., Regulatory Guides and the Code of Federal Regulations) citing the standard. The results and recommendations presented in this document have not been subjected to NRC staff review

Comparisons of ASTM standards cited in the NRC standard review plan, NUREG-0800 and related documents

International Nuclear Information System (INIS)

Ankrum, A.R.; Bohlander, K.L.; Gilbert, E.R.; Pawlowski, R.A.; Spiesman, J.B.

1995-10-01

This report provides the results of comparisons of the cited and latest versions of ASTM standards cited in the NRC Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants (NUREG 0800) and related documents. The comparisons were performed by Battelle Pacific Northwest Laboratories in support of the NRC's Standard Review Plan Update and Development Program. Significant changes to the standards, from the cited version to the latest version, are described and discussed in a tabular format for each standard. Recommendations for updating each citation in the Standard Review Plan are presented. Technical considerations and suggested changes are included for related regulatory documents (i.e., Regulatory Guides and the Code of Federal Regulations) citing the standard. The results and recommendations presented in this document have not been subjected to NRC staff review

Comparing different versions of the Rahim EI questionnaire in a South African context: A confirmatory factor analysis approach

Directory of Open Access Journals (Sweden)

Petrus Nel

2015-03-01

Full Text Available Orientation: Given the interest in the importance of emotional intelligence in employees and leaders with regard to performance of their jobs, it is imperative to use reliable and validinstruments to operationalise emotional intelligence. Research purpose: The purpose of the study was to assess the psychometric properties of three different versions of the Rahim emotional intelligence index (EQI, specifically withregard to its factor structure and reliability, using two different samples. otivation for the study: No previous study has investigated which version of the Rahim EQI is the most appropriate for conducting research within South African organisations. Inaddition, the question of whether the Rahim EQI measures a strong general factor has notbeen answered. Research approach, design, and method: A cross-sectional quantitative research design wasused. Two samples were used (n = 470 and n = 308. The first sample completed the 40-itemversion of the Rahim EQI, whilst the second sample completed the 30-item version of the Rahim EQI. The measurement model, representing the 22-item version of the Rahim EQI, was also fitted to both these samples. Confirmatory factor analysis was used to compare thedifferent versions, as well as conceptualisations, of the Rahim EQI. Main findings: The 22-item version of the Rahim EQI exhibited better model fit than the 40-item and 30-item versions. In addition, the bifactor model suggested that the Rahim EQIseems to measure a strong general factor (emotional intelligence with very little evidence ofthe presence of unique group factors (self-awareness, self-regulation, motivation, empathy and social skills. Practical/managerial implications: Both the reliability and factor structure of the 22-item version of the Rahim EQI have been confirmed. The bifactor structure should inform researchers and practitioners that, in order to understand emotional intelligence, it is better to conceptualise it as a unidimensional

Maintaining consistency between planning hierarchies: Techniques and applications

Science.gov (United States)

Zoch, David R.

1987-01-01

In many planning and scheduling environments, it is desirable to be able to view and manipulate plans at different levels of abstraction, allowing the users the option of viewing and manipulating either a very detailed representation of the plan or a high-level more abstract version of the plan. Generating a detailed plan from a more abstract plan requires domain-specific planning/scheduling knowledge; the reverse process of generating a high-level plan from a detailed plan Reverse Plan Maintenance, or RPM) requires having the system remember the actions it took based on its domain-specific knowledge and its reasons for taking those actions. This reverse plan maintenance process is described as implemented in a specific planning and scheduling tool, The Mission Operations Planning Assistant (MOPA), as well as the applications of RPM to other planning and scheduling problems; emphasizing the knowledge that is needed to maintain the correspondence between the different hierarchical planning levels.

Psychometrics of an original measure of barriers to providing family planning information: Implications for social service providers.

Science.gov (United States)

Bell, Melissa M; Newhill, Christina E

2017-07-01

Social service professionals can face challenges in the course of providing family planning information to their clients. This article reports findings from a study that developed an original 27-item measure, the Reproductive Counseling Obstacle Scale (RCOS) designed to measure such obstacles based conceptually on Bandura's social cognitive theory (1986). We examine the reliability and factor structure of the RCOS using a sample of licensed social workers (N = 197). A 20-item revised version of the RCOS was derived using principal component factor analysis. Results indicate that barriers to discussing family planning, as measured by the RCOS, appear to be best represented by a two-factor solution, reflecting self-efficacy/interest and perceived professional obligation/moral concerns. Implications for practice and future research are discussed.

A Slovenian version of the "clinical learning environment, supervision and nurse teacher scale (Cles+T)" and its comparison with the Croatian version.

Science.gov (United States)

Žvanut, Boštjan; Lovrić, Robert; Kolnik, Tamara Štemberger; Šavle, Majda; Pucer, Patrik

2018-02-26

Nursing clinical learning environments are particularly important for the achievement of good practice in clinical training of student nurses, and thus, for the nursing competence development. Hence, it is important to have an instrument consisting of reliable and valid criteria for assessing the clinical learning environment, applicable in different contexts, and translated in the respondents mother tongue. The goal of the present research was to test the reliability and validity of the Slovenian version of the "Clinical Learning Environment, Supervision and Nurse Teacher evaluation scale", and to compare it with the Croatian version. The data was collected between 10 March and 10 June 2015 at four Slovenian institutions, where nursing BSc study programmes are performed. The final sample consisted of 232 students (response rate 68.8%): 81.9% were females and 18.1% males, average age was 23. The translated instrument in Slovenian language resulted as reliable and valid, it reflects the expected five factors of the original version despite some minor problems in the factor structure and in test-retest. The most important difference between the Slovenian and Croatian version is in the factor structure regarding the implementation of roles in clinical learning environment. Copyright © 2018 Elsevier Ltd. All rights reserved.

Meteorological monitoring sampling and analysis plan for the environmental monitoring plan at Waste Area Grouping 6, Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1995-09-01

This Sampling and Analysis Plan addresses meteorological monitoring activities that wall be conducted in support of the Environmental Monitoring Plan for Waste Area Grouping (WAG) 6. WAG 6 is a shallow-burial land disposal facility for low-level radioactive waste at the Oak Ridge National Laboratory, a research facility owned by the US Department of Energy and managed by Lockheed Martin Energy Systems, Inc. Meteorological monitoring of various climatological parameters (e.g., temperature, wind speed, humidity) will be collected by instruments installed at WAG 6. Data will be recorded electronically at frequencies varying from 5-min intervals to 1-h intervals, dependent upon parameter. The data will be downloaded every 2 weeks, evaluated, compressed, and uploaded into a WAG 6 data base for subsequent use. The meteorological data will be used in water balance calculations in support of the WAG 6 hydrogeological model

Global Historical Climatology Network - Daily (GHCN-Daily), Version 2 (Version Superseded)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Please note, this dataset has been superseded by a newer version (see below). Users should not use this version except in rare cases (e.g., when reproducing previous...

Validation of the Tamil version of short form Geriatric Depression Scale-15.

Science.gov (United States)

Sarkar, Sonali; Kattimani, Shivananand; Roy, Gautam; Premarajan, K C; Sarkar, Siddharth

2015-01-01

Local language screening instruments can be helpful in early assessment of depression in the elderly in the community and primary care population. This study describes the validation of a Tamil version of Geriatric Depression Scale (short form 15 [GDS-15] item) in a rural population. A Tamil version of GDS-15 was developed using standardized procedures. The questionnaire was applied in a sample of elderly (aged 60 years and above) from a village in South India. All the participants were also assessed for depression by a clinical interview by a psychiatrist. A total of 242 participants were enrolled, 64.9% of them being females. The mean score on GDS-15 was 7.4 (±3.4), while the point prevalence of depression was 6.2% by clinical interview. The area under the receiver-operator curve was 0.659. The optimal cut-off for the GDS in this sample was found at 7/8 with sensitivity and specificity being 80% and 47.6%, respectively. The Tamil version of GDS-15 can be a useful screening instrument for assessment of depression in the elderly population.

Family planning practices of rural community dwellers in cross River State, Nigeria.

Science.gov (United States)

Etokidem, A J; Ndifon, W; Etowa, J; Asuquo, E F

2017-06-01

Nigeria is the most populous nation in Africa and the seventh most populous in the world. Despite a high fertility rate of 5.5 per woman and a high population growth rate of 3.2%, Nigeria's contraceptive prevalence is 15%, which is one of the lowest in the world. The objective of this study was to determine the knowledge of family planning and family planning preferences and practices of rural community women in Cross River State of Nigeria. This was a cross-sectional study involving 291 rural women. Convenience sampling method was used. The women were assembled in a hall and a semi-structured questionnaire was administered to every consenting woman until the sample size was attained. Data obtained from the study were analyzed using the Statistical Package for the Social Sciences version 20 and presented in tables as frequencies and percentages as well as figures. Association between categorical variables was explored using chi-square test. Binary logistic regression was also performed to determine predictors of use of at least one family planning method at some point in time. Fifty (17.2%) respondents were using at least one family planning method. One hundred and ninety-eight (68.3%) respondents had used at least one family planning method at some point in time. Reasons given for not using any family planning method included "Family planning is against my religious beliefs" (56%); "it is against our culture" (43.8%); "I need more children" (64.9%); "my partner would not agree" (35.3%); "family planning does not work" (42.9%); "it reduces sexual enjoyment" (76%); and "it promotes unfaithfulness/infidelity" (59%). Binary logistic regression conducted to predict the use of at least one family planning method at some point in time using some independent variables showed that who makes the decision regarding family planning use was the strongest predictor of family planning use (OR = 0.567; 95% CI = 0.391-0.821). This suggests that family planning uptake is more

Vietnamese validation of the short version of Internet Addiction Test

Directory of Open Access Journals (Sweden)

Bach Xuan Tran

2017-12-01

Full Text Available Background and aims: The main goal of the present study was to examine the psychometric properties of a Vietnamese version of the short-version of Internet Addiction Test (s-IAT and to assess the relationship between s-IAT scores and demographics, health related qualify of life and perceived stress scores in young Vietnamese. Methods: The Vietnamese version of s-IAT was administered to a sample of 589 participants. Exploratory factor and reliability analyses were performed. Regression analysis was used to identify the associated factors. Results: The two-factor model of Vietnamese version of s-IAT demonstrated good psychometric properties. The internal consistency of Factor 1 (loss of control/time management was high (Cronbach's alpha=0.82 and Factor 2 (craving/social problems was satisfactory (Cronbach's alpha=0.75. Findings indicated that 20.9% youths were addicted to the Internet. Regression analysis revealed significant associations between Internet addiction and having problems in self-care, lower quality of life and high perceived stress scores. Discussion and conclusions: The Vietnamese version of s-IAT is a valid and reliable instrument to assess IA in Vietnamese population. Due to the high prevalence of IA among Vietnamese youths, IA should be paid attention in future intervention programs. s-IAT can be a useful screening tool for IA to promptly inform and treat the IA among Vietnamese youths. Keywords: Factor analysis, Short-version, Internet Addiction Test, Psychometric properties, Vietnamese

Reliability and validity of the Danish version of the UCLA Loneliness Scale

DEFF Research Database (Denmark)

Lasgaard, Mathias