Separation of lanthanum (3) and samarium (3) extraction with tributylphosphate in the solvent presence of solid phase

International Nuclear Information System (INIS)

Korotkevich, I.B.; Kolesnikov, A.A.; Bomshtejn, V.E.

1990-01-01

Lanthanum (3) and samarium (3) extraction from nitric acid solutions by tributylphosphate in the presence of solid phase has been investigated. An increase in samarium α-nitrate distribution factor in the presence of solid phase with a decrease in its concentration in the initial solution and with lanthanum nitrate concentration increase is detected. The greatest effect of separation is observed in samarium nitrate microregion. The method of quantitative extraction of samarium from lanthanum nitrate solutions with samarium-lanthanum separation factor exceeding 50 has been suggested

Biodistribution study of 153Sm-EDTMP produced by irradiation of natural and enriched Samarium, in rats

International Nuclear Information System (INIS)

Meftahi, M.; Bahrami Samani, A.; Babaei, M. H.; Shamsaei Zafarghandi, M.; Ghannadi Maragheh, M.

2010-01-01

''1 53 Sm-EDTMP is one of the well known radiopharmaceuticals for pain palliation of bone metastases. Despite that, it is used just in a few countries. It is due to some reasons like being costly enriched samarium that usually used as target for irradiation and short half-life of 153 Sm. In this investigation, certain amounts of radiopharmaceuticals prepared by irradiation of enriched and natural samarium were injected to some normal rats. Then, the rodents were sacrificed and some of their organs were removed. All of the mentioned stages were performed in order to consider the possibility of exploiting natural samarium instead of enriched samarium by study of biodistribution of both radiopharmaceuticals in various organs especially in bone as the target tissue. At the end, the acceptable results were obtained using natural samarium in comparison with the enriched samarium from the point of view of the biodistribution studies.

Influence of tellurite on lifetime for samarium doped lanthanum lead borate glass

Science.gov (United States)

Madhu, A.; Eraiah, B.

2018-04-01

Samarium substituted tellurium lanthanum lead borate glass is prepared using melt quenching technique. Luminescence spectra have been recorded upon excitation with 402 nm various transitions from 4G5/2 level, for samarium doped tellurite glasses are studied and also lifetime for all the samples exhibit single exponential behaviour of decay curve. Luminescence spectra of present glasses show quenching effect due to cross-relation channels of samarium ions. The lifetime of glass samples decrease as the tellurite concentration is decreased. So, it evidences that to attain longer lifetime for lasing material one can tune the host by selecting concentration of tellurite.

A NOVEL SAMARIUM COMPLEX WITH INTERESTING ...

African Journals Online (AJOL)

delocalized π-electrons of the pyridyl rings obtains increasing attention in ... BaSO4 plate was used as a reference (100% reflectance), on which the finely ground .... several are samarium-containing complex with bipy [41-45]. Figure 2.

Radioisotopic synovectomy using ferric hydroxide macroaggregated for chronic arthritis treatment

International Nuclear Information System (INIS)

Lima, Carla Flavia; Campos, Tarcisio P.R.

2002-01-01

Synovectomy radioisotopic is an arthritis treatment used in specific clinical conditions whose main goal is to sterilized the synovia. This treatment has specific and precise indications and it is considered to have an adequate response. The present work presents a modeling of an articulation (joint) based on its real geometric anatomy and chemical constitution. The internal dosimetry is evaluated by the Monte Carlo Code. The majority of the radionuclides were considered in the simulations. The syntheses of the ferric hydroxide macroaggregates with dysprosium and samarium have been prepared (Dy 165 -MHF and Sm 153 -MHF). Obtaining the cintilographic images of rabbits in which Dy 165 -MHF is injected is in progress. Biodistribution studies in addition with the internal dosimetry will certify the dose in the membrane of the synovia. (author)

Solubility isotherms in ternary systems of samarium nitrate, water and nitrates of amidopyrine, benzotriazole

International Nuclear Information System (INIS)

Starikova, L.I.

1991-01-01

Solubility in the system of samarium nitrate-amidopyrine nitrate-water at 25 and 50 deg C was studied. Solubility isotherms consist of three branches, corresponding to crystallization of samarium nitrate tetrahydrate, amidopyrine nitrate and congruently soluble compounds of Sm(NO 3 ) 3 · 2C 13 H 17 ON 3 ·HNO 3 composition. Its thermal behaviour was studied. The system of samarium nitrate-benzotriazole nitrate-water is referred to eutonic type

Basis for developing samarium AMS for fuel cycle analysis

International Nuclear Information System (INIS)

Buchholz, Bruce A.; Biegalski, Steven R.; Whitney, Scott M.; Tumey, Scott J.; Jordan Weaver, C.

2010-01-01

Modeling of nuclear reactor fuel burnup indicates that the production of samarium isotopes can vary significantly with reactor type and fuel cycle. The isotopic concentrations of 146 Sm, 149 Sm, and 151 Sm are potential signatures of fuel reprocessing, if analytical techniques can overcome the inherent challenges of lanthanide chemistry, isobaric interferences, and mass/charge interferences. We review the current limitations in measurement of the target samarium isotopes and describe potential approaches for developing Sm-AMS. AMS sample form and preparation chemistry will be discussed as well as possible spectrometer operating conditions.

4f and 5d magnetism in samarium

International Nuclear Information System (INIS)

Stunault, A.; Bernhoeft, N.; Vettier, C.; Dumesnil, K.; Dufour, C.

2001-01-01

We report on resonant magnetic X-ray scattering studies of a samarium epitaxial film at the samarium L 3 edge. We observe one quadrupolar resonance below the edge, reflecting the polarization of the 4f electrons, and two dipolar resonances above the edge, related to the polarization of the 5d band. We demonstrate, by following the thermal evolution of resonant magnetic intensities of both types, that the polarization of the 4f and 5d electrons present exactly the same temperature dependence, even very close to the ordering temperature, in agreement with the RKKY model for long-range magnetic order in rare earths

Studies on ultrasonic velocity and electrical conductivity of samarium soaps in non-aqueous medium

International Nuclear Information System (INIS)

Mehrotra, K.N.; Chauhan, M.; Shukla, R.K.

1990-01-01

The ultrasonic velocity of solutions of samarium soaps in non-aqueous medium has been measured at a constant temperature and the results have been used to evaluate the various acoustic parameters. The pre-micellar association and the formation of micelles in samarium soap solutions have been determined by conductometric measurements. The molar conductance at infinite dilution, degree of ionisation and ionisation constant have been evaluated. The results show that samarium soaps behave as weak electrolyte in dilute solutions. (Authors)

Diffusion of samarium into cobalt in the reduction-diffusion process

International Nuclear Information System (INIS)

Freitas Nogueira, P. de; Neto, F.B.; Landgraf, F.J.G.

1998-01-01

The presence of metallic cobalt in samarium-cobalt powders is a major cause for low magnetic properties in magnets. This paper intends to investigate the effect of time and temperature in the microstructure of powders produced by reduction-diffusion. This process, developed for the production of rare earth-transition metal alloys, consists on the reduction of the rare earth oxide with metallic calcium (or calcium hydride) and its subsequent diffusion into the cobalt particle. In the present work, a mixture of samarium oxide, cobalt powder and metallic calcium was heated to 1100 or 1200 C for 2 or 4 hours in a tubular furnace under one atmosphere of purified argon. The material thereof obtained, a sintered mass is disintegrated by aqueous crepitation. The powder was evaluated in terms of its chemical composition, its samarium yield and the intermetallic compounds present. The samarium, oxygen and calcium content of the powders produced were adequate for magnet production. However, despite the massive formation of the SmCo 5 compound after 2 hours at 1100 C, final homogeneity is attained only after 4 hours at 1200 C, with the presence of SmCo 5 and Sm 2 Co 7 and the absence of the Sm 5 Co 19 compound. Also, metallic cobalt and Sm 2 Co 17 were observed in the materials produced after 2 hours at 1100 or 1200 C. (orig.)

Nonlinear Faraday rotation in samarium vapor

International Nuclear Information System (INIS)

Barkov, L.M.; Melik-Pashaev, D.A.; Zolotorev, M.S.

1988-01-01

Experiments on nonlinear magnetic optical (Faraday) rotation on resonance transitions of atomic samarium are described. Measurements were carried out on transitions with different angular momenta of upper and lower states: 1→0, 0→1 and 1→1. Qualitative explanations of observed phenomena are given

Plasma sprayed samarium--cobalt permanent magnets

International Nuclear Information System (INIS)

Willson, M.C.; Janowiecki, R.J.

1975-01-01

Samarium--Co permanent magnets were fabricated by arc plasma spraying. This process involves the injection of relatively coarse powder particles into a high temperature gas for melting and spraying onto a substrate. The technique is being investigated as an economical method for fabricating Co--rare earth magnets for advanced traveling wave tubes and cross-field amplifiers. Plasma spraying permits deposition of material at high rates over large areas with optional direct bonding to the substrate, and offers the ability to fabricate magnets in a variety of shapes and sizes. Isotropic magnets were produced with high coercivity and good reproducibility in magnetic properties. Post-spray thermal treatments were used to enhance the magnetic properties of sprayed deposits. Samarium--Co magnets, sprayed from Sm-rich powder and subjected to post-spray heat treatment, displayed energy products in excess of 9 million G-Oe and coercive forces of approximately 6000 Oe. Bar magnet arrays were constructed by depositing magnets on ceramic substrates

Magnetoresistance of samarium in the 4.2-300 K range

International Nuclear Information System (INIS)

Trubitsyn, V.A.; Shalashov, V.F.

1980-01-01

Electric conductivity, transverse and longitudinal magnetoresistance of polycrystalline samarium with the purity of 99.9% in the 4.2-300 K temperature range and in magnetic fields up to 50 ke, are measured. The constituent of specific electric conductivity caused by spin disorder is 30.7 μOhmxcm, m*/m=2.6, the exchange parameter is G=3.1 eVxA 3 . Both transverse and longitudinal magnetoresistance are positive at 4.2 K; and the increase of temperature reveals a number of anomalies, evidently conditioned by the alteration of samarium magnetic structure

Aluminum Hydroxide and Magnesium Hydroxide

Science.gov (United States)

Aluminum Hydroxide, Magnesium Hydroxide are antacids used together to relieve heartburn, acid indigestion, and upset stomach. They ... They combine with stomach acid and neutralize it. Aluminum Hydroxide, Magnesium Hydroxide are available without a prescription. ...

Conductometric investigations on samarium soaps

International Nuclear Information System (INIS)

Mehrotra, K.N.; Chauhan, Mithlesh; Shukla, R.K.

1989-01-01

The critical micelle concentration (CMC), degree of dissociation and dissociation constant of samarium soaps (valerate, caproate, caprylate and caprate) in a mixture of 60 per cent benzene and 40 per cent methanol were determined by using conductometric measurements. The soaps behaved as simple electrolyte in dilute solutions and the CMC was found to decrease with increasing chainlength of the fatty acid constituent of the soap. (author). 7 refs., 2 tabs

Optical isotope shifts for unstable samarium isotopes

International Nuclear Information System (INIS)

Eastham, D.A.; Walker, P.M.; Griffith, J.A.R.; Evans, D.E.; Grant, I.S.; England, J.G.; Fawcett, M.J.

1984-01-01

Using a tunable dye laser beam intersecting a thermal atomic beam, optical isotope shifts and hyperfine splittings have been measured for the four unstable samarium isotopes between 144 Sm and 154 Sm, covering the well known transition region from spherical to deformed shapes. (orig.)

The samarium Grignard reaction. In situ formation and reactions of primary and secondary alkylsamarium(III) reagents

Energy Technology Data Exchange (ETDEWEB)

Curran, D.P.; Totleben, M.J. [Univ. of Pittsburgh, PA (United States)

1992-07-15

This work shows that primary and secondary radicals are rapidly reduced in THF/HMPA to form primary- and secondary-alkylsamarium reagents. The primary- and secondary-radicals can be formed either by direct SmI{sup 2} reductions of primary- and secondary-halides or by a previous rapid radical cyclization. The samarium reagents have moderate stability in solution, and they react with a variety of typical electrophiles, including aldehydes and ketones. The work further shows that organosamarium intermediates can be involved in the traditional samarium Barbier reaction of aldehydes and ketones conducted in THF/HMPA. A new procedure called the {open_quotes}samarium Grignard{close_quotes} method is introduced, and it is suggested that this new procedure will have considerably more scope and generality than the samarium Barbier reaction. 37 refs., 4 tabs.

Fluorimetric determination of samarium(III) and europium(III) in neodymium oxide by separation with a resin column

Energy Technology Data Exchange (ETDEWEB)

Shaorong Liu; Jian Meng (Beijing Research Institute of Chemical Engineering and Metallurgy (China)); Wenhua Liu (General Research Institute for Non-Ferrous Metals (China))

1992-08-24

When thenoyltrifluoroacetone-phenanthroline-Triton X-100 is used to determine samarium(III) and europium(III) fluorimetrically, only a limited amount of neodymium(III) can be tolerated. By using an on- line separation which can partially separate neodymium(III) from samarium(III), a practical and convenient method was developed to detect samarium(III) at concentrations >0.05% and europium(III) at concentrations >0.005% in neodymium oxide. (author). 7 refs.; 4 figs.; 3 tabs.

Fluorimetric determination of samarium(III) and europium(III) in neodymium oxide by separation with a resin column

International Nuclear Information System (INIS)

Shaorong Liu; Jian Meng; Wenhua Liu

1992-01-01

When thenoyltrifluoroacetone-phenanthroline-Triton X-100 is used to determine samarium(III) and europium(III) fluorimetrically, only a limited amount of neodymium(III) can be tolerated. By using an on- line separation which can partially separate neodymium(III) from samarium(III), a practical and convenient method was developed to detect samarium(III) at concentrations >0.05% and europium(III) at concentrations >0.005% in neodymium oxide. (author). 7 refs.; 4 figs.; 3 tabs

ppt level detection of samarium(III) with a coated graphite sensor based on an antibiotic.

Science.gov (United States)

Ganjali, Mohammad Reza; Rezapour, Morteza; Pourjavid, Mohammad Reza; Haghgoo, Soheila

2004-07-01

N-[2-[4-[[[(Cyclohexylamino)carbonyl]amino]sulfonyl]phenyl]ethyl]-5-methyl pyrazine carboxamide (glipizid) was explored as an electro-active material for preparing a polymeric membrane-based sensor selective to samarium ions. The membrane incorporated 30% poly(vinyl chloride) (PVC), 53% benzyl acetate (BA), 11% glipizid and 6% sodium tetraphenyl borate. When coated on the surface of a graphite electrode, it exhibits Nernstian responses in the concentration range of 1.0 x 10(-5) to 1.0 x 10(-10) M, with a detection limit of 8.0 x 10(-11)M samarium. The electrode shows high selectivity towards samarium over several cations (alkali, alkaline earth, transition and heavy metal ions), and specially lanthanide ions. The proposed sensor has a very short response time (pH range for at least ten weeks. It was used as an indicator electrode in potentiometric titration of Sm(III) ions with an EDTA solution, and for determination of samarium in binary and ternary mixtures.

Adsorption and the initial stages of samarium condensation on iridium coated by graphite monolayer

International Nuclear Information System (INIS)

Abdullaev, R.M.; Tontegode, A.Ya.; Yusifov, F.K.

1978-01-01

Adsorption and the initial stages of vacuum samarium condensation on iridium coated by graphite monolayer (valent-saturated neutral substrate) were studied by the thermodesorption mass-spectrometry and thermoemission methods, and were compared with samarium adsorption and condensation on iridium. Desorption heat of samarium atoms with thin coating of Ir-C, equal to E approximately 1.9 eV has been determined. For desorption with Ir E is approximately 6 eV. Such a great difference in desorption heats is connected with the reduction of covalent constituent of adsorption bond in a neutral substrate. Samarium on Ir-C is found to be condensated in two states: loosely bound and tightly bound which sharply differ in properties. The tightly bound state is characterized by abnormally low vapour pressure. Possible nature of this state is discussed. Double effect on the condensation of the substrate valent saturation is noted. On the one hand, the reduction of the particle bond with the substrate decreases their concentration on the surface, preventing condensation. On the other hand, the release of the valent eloctrons of adatous brings about strong lateral interaction between them, which in its turn, promotes condensation during eased migration on the neutral substrate

Solar nebula heterogeneity in p-process samarium and neodymium isotopes.

Science.gov (United States)

Andreasen, Rasmus; Sharma, Mukul

2006-11-03

Bulk carbonaceous chondrites display a deficit of approximately 100 parts per million (ppm) in 144Sm with respect to other meteorites and terrestrial standards, leading to a decrease in their 142Nd/144Nd ratios by approximately 11 ppm. The data require that samarium and neodymium isotopes produced by the p process associated with photodisintegration reactions in supernovae were heterogeneously distributed in the solar nebula. Other samarium and neodymium isotopes produced by rapid neutron capture (r process) in supernovae and by slow neutron capture (s process) in red giants were homogeneously distributed. The supernovae sources supplying the p- and r-process nuclides to the solar nebula were thus disconnected or only weakly connected.

Crystallization of Yttrium and Samarium Aluminosilicate Glasses

OpenAIRE

Lago, Diana Carolina; Prado, Miguel Oscar

2016-01-01

Aluminosilicate glasses containing samarium and yttrium (SmAS and YAS glasses) exhibit high glass transition temperatures, corrosion resistance, and glass stability on heating which make them useful for technological applications. Yttrium aluminosilicate glass microspheres are currently being used for internal selective radiotherapy of liver cancer. During the preparation process, crystallization needs to be totally or partially avoided depending on the final application. Thus knowing the cry...

Determination of 0.01–0.1% of samarium in 40–100 mg of lead chloride

NARCIS (Netherlands)

Agterdenbos, J.; Jütte, B.A.H.G.; Schuring, J.

1971-01-01

A method is described for the determination of 5–25 μg of samarium in about 40 mg of lead chloride, based on the removal of the lead by electrolysis and determination of the samarium by extraction with PAN and measurement of the extinction of the complex at 552 nm.

Synthesis and structure of unprecedented samarium complex with bulky bis-iminopyrrolyl ligand via intramolecular C=N bond activation

Energy Technology Data Exchange (ETDEWEB)

Das, Suman; Anga, Srinivas; Harinath, Adimulam; Panda, Tarun K. [Department of Chemistry, Indian Institute of Technology, Hyderabad (India); Pada Nayek, Hari [Department of Applied Chemistry, Indian Institute of Technology, (ISM) Dhanbad, Jharkhand (India)

2017-12-29

An unprecedentate samarium complex of the molecular composition [{κ"3-{(Ph_2CH)N=CH}{sub 2}C{sub 4}H{sub 2}N}{κ"3-{(Ph_2CHN=CH)(Ph_2CHNCH)C_4H_2N}Sm}{sub 2}] (2), which was isolated by the reaction of a potassium salt of 2,5-bis{N-(diphenylmethyl)-iminomethyl}pyrrolyl ligand [K(THF){sub 2}{(Ph_2CH)N=CH}{sub 2}C{sub 4}H{sub 2}N] (1) with anhydrous samarium diiodide in THF at 60 C through the in situ reduction of imine bond is presented. The homoleptic samarium complex [[κ{sup 3}-{(Ph_2CH)-N=CH}{sub 2}C{sub 4}H{sub 2}N]{sub 3}Sm] (3) can also be obtained from the reaction of compound 1 with anhydrous samarium triiodide (SmI{sub 3}) in THF at 60 C. The molecular structures of complexes 2 and 3 were established by single-crystal X-ray diffraction analysis. The molecular structure of complex 2 reveals the formation of a C-C bond in the 2,5-bis{N-(diphenylmethyl)iminomethyl}pyrrole ligand moiety (Ph{sub 2}Py{sup -}). However, complex 3 is a homoleptic samarium complex of three bis-iminopyrrolyl ligands. In complex 2, the samarium ion adopts an octahedral arrangement, whereas in complex 3, a distorted three face-centered trigonal prismatic mode of nine coordination is observed around the metal ion. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Effect of samarium in corrosion and microstructure of Al-5Zn-0.5Cu as low driving voltage sacrificial anode

Science.gov (United States)

Pratesa, Yudha; Ferdian, Deni; Ramadhan, Fajar Yusya; Maulana, Bramuda

2018-05-01

Sacrificial Anode Low voltage is the latest generation of the sacrificial anode that can prevent the occurrence of Hydrogen Cracking (HIC) due to overprotection. The Al-5n-0.5Cu alloy showed the potential to be developed as the new sacrificial anode. However, the main problem is copper made Al2Cu intermetallic in grain boundary. Samarium is added to modify the shape of the intermetallic to make it finer and make the corrosion uniform. Several characterizations were conducted to analyze the effect of Samarium. Scanning electron microscope (SEM) and Energy dispersive spectroscopy was used to analyzed the microstructure of the alloy. Metallography preparation was prepared for SEM analysis. Corrosion behavior was characterized by cyclic polarization in 3.5% NaCl solution. The results show samarium can change the shape of intermetallic and refine the grains. In addition, samarium makes better pitting resistance and exhibits a tendency for uniform corrosion. It is indicated by the loop reduction (ΔEpit-prot). Current density increased as an effect of samarium addition from 6x10-5 Ampere (Al-5Zn-0.5Cu) to 2.5x10-4 Ampere (Al-5Zn-0.5Cu-0.5Sm). Steel potential protection increased after addition of samarium which is an indication the possibility of Al-Zn-Cu-Sm to be used as low voltage sacrificial anode.

Ultrasonic and viscosimetric studies of samarium laurate in benzene-dimethylsulfoxide mixtures

International Nuclear Information System (INIS)

Mehrotra, K.N.; Anis, M.

1995-01-01

Ultrasonic and viscosity measurements of samarium laurate in benzene-DMSO mixtures of different compositions (7:3 and 1:1 V/V) have been used to determine the critical micelle concentration (CMC), soap-solvent interaction, and various acoustic parameters of the system. The values of critical micelle concentration increase with increasing amount of DMSO in the solvent mixtures. The viscosity results have been explained on the basis of equations proposed by Einstein, Vand. Moulik, and Jones-Dole. The values of CMC for samarium laurate obtained from the viscosity measurements are in agreement with the results obtained from ultrasonic measurements. The results show that the soap molecules do not aggregate appreciably below CMC there is a marked change in the aggregation behaviour at CMC. (author)

Behavior of Samarium III during the sorption process; Comportamiento del Samario-III durante el proceso de sorcion

Energy Technology Data Exchange (ETDEWEB)

Ordonez R, E.; Garcia G, N.; Garcia R, G. [ININ, Carr. Mexico-Toluca Km 36.5, Salazar, Estado de Mexico (Mexico)]. e-mail: edo@nuclear.inin.mx

2004-07-01

In this work the results of the behavior of samarium in solution are presented, in front of a fine powder of zirconium silicate (zircon). For that which is necessary to characterize the zircon, studying the crystallinity, the morphology, the surface area and the isoelectric point. The behavior of samarium in solution is studied by means of the elaboration of isotherm of sorption, using the technique by lots. One observes that to pH values of nearer to the isoelectric point (pH = 7.23) the process of sorption of the samarium begins, reaching a maximum to near pH at 9. The technique of luminescence is used to determine the concentration of the sipped samarium (phosphorescence) and also to make the speciation of the species formed in the surface of the zircon (phosphorescence). The results can be extrapolated with the plutonium when making the modeling of the migration of alpha emitting coming from the repositories of radioactive waste since both they have similar chemical properties (they are homologous). (Author)

Inductively coupled plasma optical emission spectrometry analysis of lanthanum, samarium and gadolinium oxides for rare earths impurities

International Nuclear Information System (INIS)

Reino, L.C.P.; Lordello, A.R.

1990-09-01

An inductively coupled plasma optical emission spectrometry method is described for the determination of Sm, Eu, La, Gd, Dy, Pr, Ho, Nd, Tb and Y in purified oxides of lanthanum, samarium and gadolinium. The method enables a simple, precise and readily available determination. Dissolution of the samples is achieved with diluted hydrochloric acid (1:1). The solutions are diluted to volume for a concentration of 1mg/ml. The lowest determination limit is 0,01% for most elements and 0,05 or 0,1% for a few rare earths in samarium and gadolinium matrices. Lanthanum, Samarium and Gadolinium concentrates with purity grade of 99,9%, 99,6% and 99,8%, respectively, can be analysed by this procedure. (author)

Sodium Hydroxide and Calcium Hydroxide Hybrid Oxygen Bleaching with System

Science.gov (United States)

Doelle, K.; Bajrami, B.

2018-01-01

This study investigates the replacement of sodium hydroxide in the oxygen bleaching stage using a hybrid system consisting of sodium hydroxide calcium hydroxide. Commercial Kraft pulping was studied using yellow pine Kraft pulp obtained from a company in the US. The impact of sodium hydroxide, calcium hydroxide hybrid system in regard to concentration, reaction time and temperature for Kraft pulp was evaluated. The sodium hydroxide and calcium hydroxide dosage was varied between 0% and 15% based on oven dry fiber content. The bleaching reaction time was varied between 0 and 180 minutes whereas the bleaching temperature ranged between 70 °C and 110 °C. The ability to bleach pulp was measured by determining the Kappa number. Optimum bleaching results for the hybrid system were achieved with 4% sodium hydroxide and 2% calcium hydroxide content. Beyond this, the ability to bleach pulp decreased.

Pemisahan Unsur Samarium dan Yttrium dari Mineral Tanah Jarang dengan Teknik Membran Cair Berpendukung (Supported Liquid Membrane

Directory of Open Access Journals (Sweden)

Amri Amin

2009-06-01

Full Text Available he increasing use of rare earth elements in high technology industries needs to be supported by developmental work for the separation of elements. The research objective is fiercely attracting and challenging considering the similarity of bath physical and chemical properties among these elements. The rate separation of samarium and yttrium elements using supported liquid membrane has been studied. Polytetrafluoroethylene (PTFE with pore size of 0.45 µm has been used as the membrane and di(2-ethylhexyl phosphate (D2EHP in hexane has been used as a carrier and nitric acid solution has been used as receiving phase. Result of experiments showed that the best separation rate of samarium and yttrium elements could be obtained at feeding phase of pH 3.0, di(2-ethylhexyl phosphate (D2EHP concentration of 0.3 M, agitation rate of 700 rpm, agitation time of 2 hours, and nitric acid and its solution concentrations of 1.0 M and 0.1 M, respectively. At this condition, separation rates of samarium and yttrium were 64.4 and 67.6%, respectively.   Keywords: liquid membrane, rare earth elements, samarium, yttrium

Application of magnesium hydroxide and barium hydroxide for the ...

African Journals Online (AJOL)

Application of magnesium hydroxide and barium hydroxide for the removal of metals and sulphate from mine water. ... equivalent to the Ba(OH)2 dosage. During CO2-dosing, CaCO3 is precipitated to the saturation level of CaCO3. Keywords: Magnesium hydroxide; barium hydroxide; sulphate removal; water treatment ...

Preparation and examination of properties of samarium-153-EDTMP complex

International Nuclear Information System (INIS)

Nowak, M.; Garnuszek, P.; Lukasiewicz, A.; Wozniak, I.; Zulczyk, W.; Licinska, I.

1995-01-01

Preparation and properties of ethylenediaminetetramethylenephosphonic acid (EDTMP) as well as some properties of 153 Sm-EDTMP chelate have been examined. The chelate formed by samarium-153 (46.3 h, β - -decay) with EDTMP exhibits high bone uptake and can be used for treatment of disseminated, painful skeletal metastases. The purity and stability of solutions of 153 Sm-EDTMP chelate were examined in a broad range of samarium concentration and 153 Sm specific activity. The complex under study was examined by radio-TLC, -electrophoresis and radio-HPLC. The results obtained suggest the small size of molecules of 153 Sm-EDTMP chelate as compared with molecules of ''free''EDTMP. The results of biodistribution of 153 Sm-EDTMP determined in rats indicate the quick blood clearance, high deposition of radioactivity in bone and quick excretion of radioactivity into urine. No specific uptake of 153 Sm-EDTMP in extra-skeletal organs was found. (author). 42 refs, 13 figs, 22 tabs

Expedient Method for Samarium(II) Iodide Preparation Utilizing a Flow Approach

Czech Academy of Sciences Publication Activity Database

Voltrová, Svatava; Šrogl, Jiří

2013-01-01

Roč. 24, č. 3 (2013), s. 394-396 ISSN 0936-5214 R&D Projects: GA MŠk LH12013 Institutional support: RVO:61388963 Keywords : flow * samarium * iodide * reduction Subject RIV: CC - Organic Chemistry Impact factor: 2.463, year: 2013

Optical properties of zinc–vanadium glasses doped with samarium ...

Indian Academy of Sciences (India)

Abstract. Zinc–vanadium glasses doped with samarium oxide having the chemical composition Sm2O3(x). ZnO(40−x)V2O5(60)(where x = 0·1–0·5 mol%) were prepared by melt quenching method. The density of these glasses was measured by Archimedes method; the corresponding molar volumes have also been ...

Nickel hydroxide electrode. 3: Thermogravimetric investigations of nickel (II) hydroxides

Science.gov (United States)

Dennstedt, W.; Loeser, W.

1982-01-01

Water contained in Ni hydroxide influences its electrochemical reactivity. The water content of alpha and beta Ni hydroxides is different with respect to the amount and bond strength. Thermogravimetric experiments show that the water of the beta Ni hydroxides exceeding the stoichiometric composition is completely removed at 160 deg. The water contained in the interlayers of the beta hydroxide, however, is removed only at higher temperatures, together with the water originating from the decomposition of the hydroxide. These differences are attributed to the formation of II bonds within the interlayers and between interlayers and adjacent main layers. An attempt is made to explain the relations between water content and the oxidizability of the Ni hydroxides.

X-ray spectrum in the range (6-12) A emitted by laser-produced plasma of samarium

International Nuclear Information System (INIS)

Louzon, Einat; Henis, Zohar; Levi, Izhak; Hurvitz, Gilad; Ehrlich, Yosi; Fraenkel, Moshe; Maman, Shlomo; Mandelbaum, Pinchas

2009-01-01

A detailed analysis of the x-ray spectrum emitted by laser-produced plasma of samarium (6-12 A) is presented, using ab initio calculations with the HULLAC relativistic code and isoelectronic considerations. Resonance 3d-nf (n=4 to 7), 3p-4d, 3d-4p, and 3p-4s transitions in Ni samarium ions and in neighboring ionization states (from Mn to Zn ions) were identified. The experiment results show changes in the fine details of the plasma spectrum for different laser intensities.

Synthesis of samarium binding bleomycin - a possible NCT radiosensitizer

Energy Technology Data Exchange (ETDEWEB)

Mendes, B.M., E-mail: bmm@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Mendes, T.M.; Campos, T.P.R., E-mail: campos@nuclear.ufmg.b [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil)

2011-07-01

Bleomycin (BLM) is a drug that has attractive features for the development of a new radiopharmaceutical, particularly with regard to neutron capture therapy (NCT) sensitized by Sm-149. It has the ability to chelate many metal ions. In vitro studies have shown that up to 78% of BLM present in a cell is accumulated inside the nucleus or in the nuclear membrane. In addition, this drug has higher affinity for tumor tissues than for normal tissues. Radioactive isotopes carried by this antibiotic would be taken preferentially to one important cellular targets DNA. Besides, BLM displays intrinsic anti-tumor activity - it is a chemotherapic antibiotic clinically used against some cancers. This study aimed to obtain bleomycin molecules bound to samarium (BLM-Sm) for NCT studies in vitro and in vivo. The binding technique employed in this work has great simplicity and low cost. Thin layer chromatography, high performance liquid chromatography, fast protein liquid chromatography and analysis by ICP-AES were applied to verify the binding molecule. ICP-AES results showed the presence of samarium in the sample peaks related to BLM-Sm. However, efficiency and stability of this bond needs to be investigated. (author)

Synthesis of samarium binding bleomycin - a possible NCT radiosensitizer

International Nuclear Information System (INIS)

Mendes, B.M.; Mendes, T.M.; Campos, T.P.R.

2011-01-01

Bleomycin (BLM) is a drug that has attractive features for the development of a new radiopharmaceutical, particularly with regard to neutron capture therapy (NCT) sensitized by Sm-149. It has the ability to chelate many metal ions. In vitro studies have shown that up to 78% of BLM present in a cell is accumulated inside the nucleus or in the nuclear membrane. In addition, this drug has higher affinity for tumor tissues than for normal tissues. Radioactive isotopes carried by this antibiotic would be taken preferentially to one important cellular targets DNA. Besides, BLM displays intrinsic anti-tumor activity - it is a chemotherapic antibiotic clinically used against some cancers. This study aimed to obtain bleomycin molecules bound to samarium (BLM-Sm) for NCT studies in vitro and in vivo. The binding technique employed in this work has great simplicity and low cost. Thin layer chromatography, high performance liquid chromatography, fast protein liquid chromatography and analysis by ICP-AES were applied to verify the binding molecule. ICP-AES results showed the presence of samarium in the sample peaks related to BLM-Sm. However, efficiency and stability of this bond needs to be investigated. (author)

Influence of pretreatment temperature cycling on the radiating defect formation in silicon doped by samarium

International Nuclear Information System (INIS)

Abdurakhmanov, K.P.; Nazyrov, D.E.

2006-01-01

Full text: The raise of thermal and radiation stability as it is known, is one of actual problems of physics semiconductors. Recently it is established, that the rare-earth elements (REE) raise a stability of silicon to exterior action. In this connection the investigation of silicon doped REE by samarium and influence on its properties of heat treatments and radiation exposure is important. In sectional operation the outcomes of investigations of influence of samarium on thermal (600 degree C are reduced; 600 deg. + 900 deg. C; 900 deg. C; 900 deg. C + 600 deg. C; 1100 deg. C; 600 deg. C + 900 deg. C + 1100 deg. C; 900 deg. C + 600 deg. C + 1100 deg. C) thermal defect formation and radiation defect formation (exposure of γ-quanta 60 Co) both in beforehand wrought, and in thermally unfinished samples. After each cycle of heat treatments samples cool fast (throwing off in oil) or slowly (together with the furnace). Doping n-silicon REE by gadolinium and samarium was carried out during cultivation. The concentration of gadolinium and samarium in silicon, on sectional of a neutron-activation analysis was equaled 10 14 - 10 18 cm -3 . As control is model monocrystal silicon such as KEP-15/50. Para-meters of deep levels originating in control and doped REE samples, both past heat treatment or temperature cycling, and irradiated by the γ-quanta are defined by methods of a capacity spectroscopy: DLTS and IRC. The obtained outcomes have shown, that in irradiated with the γ-quanta 60 Co deep levels samples are formed with energies: E C -0,17 eV, E C -0,32 eV, EC-0,41 eV. Thus the parameters of deep levels vary depending on requirements of prestress heat treatment. For example heat treatment at 600 deg. C essentially increments a velocity of introduction of and centre (deep level of E C -0,17 eV), in comparison with a velocity of introduction of this level in samples with prestress heat treatment at 900 deg. C. In samples n-Si doped by samarium effectiveness of formation

Sorption of samarium in iron (II) and (III) phosphates in aqueous systems

International Nuclear Information System (INIS)

Diaz F, J.C.

2006-01-01

The radioactive residues that are stored in the radioactive confinements its need to stay isolated of the environment while the radioactivity levels be noxious. An important mechanism by which the radioactive residues can to reach the environment, it is the migration of these through the underground water. That it makes necessary the investigation of reactive materials that interacting with those radionuclides and that its are able to remove them from the watery resources. The synthesis and characterization of materials that can be useful in Environmental Chemistry are very important because its characteristics are exposed and its behavior in chemical phenomena as the sorption watery medium is necessary to use it in the environmental protection. In this work it was carried out the sorption study of the samarium III ion in the iron (II) and (III) phosphate; obtaining the sorption isotherms in function of pH, of the phosphate mass and of the concentration of the samarium ion using UV-visible spectroscopy to determine the removal percentage. The developed experiments show that as much the ferrous phosphate as the ferric phosphate present a great affinity by the samarium III, for what it use like reactive material in contention walls can be very viable because it sorption capacity has overcome 90% to pH values similar to those of the underground and also mentioning that the form to obtain these materials is very economic and simple. (Author)

Impact of educational strategies in positioning Samarium-153 EDTMP as a treatment for metastatic bone pain

International Nuclear Information System (INIS)

Seminario, C.; Morales, R.; Castro, M.; Cano, R.A.; Mendoza, G.

2005-01-01

To educate is a difficult task but its results make efforts worthwhile. Many patients in Peru suffer from intractable bone pain due to metastases. Since 1993 radionuclides were used to palliate bone pain due to metastases in Peru. First, with the help of the IAEA, Peru participated in a clinical trial using Phosphorus 32 and Strontium 89. Then, efforts were performed to produce Samarium 153 EDMTP locally, which was achieved in 1995. Nevertheless, years passed and Samarium use did not increase proportionally to the needs of people with cancer and bone pain, mainly the poor. Educational strategies have been proven useful for delivering solutions to many health problems in other diseases and also in cancer. Health education makes patients and their relatives assume responsible care of their problems. The purpose of this work was to increase Samarium EDTMP use as palliative treatment in patients with bone pain due to metastases, using educational strategies as means to change attitudes towards this health problem. In September 2003, a task group conducted studies in order to apply several methods to achieve the goal of increasing Samarium EDTMP use. Educational strategies employed were performed to provide verbal and written information to patients, physicians, medical students, residents, pain specialists, oncologists and neurologists, as well as general public. Verbal information included radio interviews, television spots and a phone number (in charge of two secretaries, prepared for answering and if not possible, a physician was in charge of attending patient consultation), e-mail and a web page for consultation. Written material was delivered to several newspapers, including clinical use of Samarium, possibilities of being elected for treatment, benefits and risks and a photography of the product. Politics of the institution producing Samarium changed, in order to achieve minimum cost of the product and it was delivered to all publics at the lowest cost for a year

Lanthanum (samarium) nitrate-4-aminoantipyrine nitrate-water systems

International Nuclear Information System (INIS)

Starikova, L.I.; Zhuravlev, E.F.

1985-01-01

Using the isothermal method of cross-sections at 50 deg C systems lanthanum nitrate-4-aminoantipyrine nitrate-water (1), samarium nitrate-4-aminoantipyrine nitrate-water (2), are studied. Isotherms of system 1 consist of two crystallization branches of initial salt components. In system 2 formation of congruently soluble compounds of the composition Sm(No) 3 ) 3 xC 11 H 13 ON 3 xHNO 3 is established. Analytical, X-ray phase and thermogravimetric analysis of the isolated binary salt are carried out

Collective effects in even-mass samarium isotopes by polarized-proton scattering

NARCIS (Netherlands)

Petit, R.M.A.L.; Hall, van P.J.; Klein, S.S.; Moonen, W.H.L.; Nijgh, G.J.; Overveld, van C.W.A.M.; Poppema, O.J.

1993-01-01

The even-mass samarium isotopes 148,...,152Sm have been investigated by polarized proton scattering at 20.4 MeV beam energy. The data have been analysed with an 'extended' optical model, where the intensities of the first maxima of the main inelastic channels are fitted in a coupled-channels

Synthesis of samarium, europium and ytterbium acetylenides

International Nuclear Information System (INIS)

Bochkarev, M.N.; Fedorova, E.A.; Glushkova, N.V.; Protchenko, A.V.; Druzhkov , O.N.; Khorshev, S.Ya.

1995-01-01

Ethynyl complexes of samarium, europium and ytterbium were prepared by interaction of naphthalinides of metals with acetylene in tetrahydrofuran. The compounds are isolated in the form of dark-coloured pyrophore powders. Data of magnetic measurements suggest that in the course of the reaction Sm(2) is oxidized completely to Sm(3), Yb(2) transforms into Yb(3) partially, whereas europium preserves its initial bivalent state. Hydrolysis of the compounds prepared provides acetylene, ethylene, ethane and hydrogen which indicates the presence of acethylenide Ln 2 C 2 and hydride LnH groupings (Ln = Sm, Eu, Yb). 9 refs., 2 tabs

Sorption-desorption of samarium in Febex bentonite

International Nuclear Information System (INIS)

Ramirez-Guinart, O.; Rigol, A.; Vidal, M.; Fernandez-Poyatos, P.; Alba, M. D.

2012-01-01

Document available in extended abstract form only. The chemical and physical nature of the clay is a key issue in the design of engineered barriers. The FEBEX bentonite is one of the clays candidates to be used in engineered barriers in deep geology repositories (DGR). Here, its performance was tested with respect to the sorption-desorption of samarium, which is a lanthanide that, besides being considered as a natural analogue of actinides, may also be present in high level radioactive waste in the form of the radioactive isotope 151 Sm. FEBEX bentonite was used in this study. This is a di-octahedral smectite, with isomorphic substitutions in tetrahedral and octahedral sheets. Its theoretical cation exchange capacity value is 1500 meq kg -1 . Sorption isotherms were obtained for Sm in the range of initial concentrations of 0.01 and 9 meq l -1 . Tests were carried out in deionized water and in a medium simulating the composition of interstitial water. Sorption tests were performed equilibrating 30 ml of the Sm solution with 0.2 g of clay. After a contact time of 24 hours, supernatants were decanted off after centrifugation. The quantification of the concentration of Sm in the initial and final solutions allowed us to quantify the Sm equilibrium concentration (C eq ), the fraction sorbed in the FEBEX bentonite (C sorb ) and to derive the sorption K d data. Desorption tests were applied to determine the desorption K d and the percentage of Sm reversibly sorbed. Desorption tests were performed with the bentonite residue from the sorption step, under the same experimental conditions, but without Sm. Powder X-ray diffractograms were obtained from 3 to 70 deg. 2θ with a step of 0.05 deg. and a counting time of 3 s. The crystalline phases were identified using the computer program X'Pert HighScore. The morphology of the samples was analyzed by SEM at 20 kV. An EDX system was fitted to the SEM equipment to perform chemical analyses of the samples using a Si/Li detector

Laser spectroscopy of atomic samarium

International Nuclear Information System (INIS)

Barkov, L.M.; Melik-Pashaev, D.A.; Zolotorev, M.S.

1988-01-01

Samarium spectrum was studied with a purpose to find transitions to be used in experiments on parity nonconservation. Macaluso-Corbino effect - Faraday rotation near resonance was used for the search and study of spectral lines. We have identified previously unknown energy levels belonging to the 4f 5 6s 2 5 D term: 15914.55(3) cm -4 (J=1), 17864.29(3) cm -4 (J=2), 20195.76(3) cm -4 (J=3). M1-transitions to these levels from the levels of the ground 4f 5 6s 2 7 F term were observed. There are several peculiarities of these transitions which are due to the fact that they occut within an inner 4f 5 -shell, particularly, a very small presuure broadening by inert gases. 44 refs.; 17 figs.; 7 tabs

Synthesis of samarium complexes with the derivative binder of Schiff Quinolinic base. Characterization and photophysical study

International Nuclear Information System (INIS)

Lucas H, J.

2016-01-01

In this work we determined the metal: binder stoichiometry of the species formed during the UV/Vis spectrophotometric titration of the derivative binder of Schiff quinolinic base, L1 with the samarium nitrate pentahydrate in methanol. Statistical analysis of the data allowed proposing the metal: binder stoichiometry for the synthesis of the complexes which was one mole of samarium salt by 2.5 moles of binder and thus favor the formation of complexes with 1M: 1L and 1M: 2L stoichiometries. They were synthesized in aqueous-organic medium (water-ethanol), isolated and purified two complexes with stoichiometry 1 Sm: 1 L1, complex 1 and 1 Sm: 2 L1, complex 2. The overall yield of the reaction was 76%. The characterization of the formed complexes was performed by visible ultraviolet spectrometry (UV/Vis), nuclear magnetic resonance, X-ray photoelectron spectroscopy (XP S), thermal gravimetric analysis with differential scanning calorimetry (TGA/DSC), and radial distribution function. These complexes were studied by fluorescence and emission phosphorescence at variable temperature. Spectroscopic techniques used in both solution and solid demonstrated the formation and stability of these complexes. In addition XP S indicated that in both complexes the samarium retains its oxidation state 3+. Luminescence studies indicated that there is intra-binding charge transfer which decreases the transfer of light energy from the binder to the samarium. Based on the experimental results, L1 binder molecules and complexes 1 and 2 were modeled that demonstrated the proposed Nc for each complex, as well as allowed to visualize the structural arrangement of the molecules, complexes and binder. (Author)

Magnesium Hydroxide

Science.gov (United States)

Magnesium hydroxide is used on a short-term basis to treat constipation.This medication is sometimes prescribed ... Magnesium hydroxide come as a tablet and liquid to take by mouth. It usually is taken as ...

Aluminum Hydroxide

Science.gov (United States)

Aluminum hydroxide is used for the relief of heartburn, sour stomach, and peptic ulcer pain and to ... Aluminum hydroxide comes as a capsule, a tablet, and an oral liquid and suspension. The dose and ...

Removal of trivalent samarium from aqueous solutions by activated biochar derived from cactus fibres

Institute of Scientific and Technical Information of China (English)

Loukia Hadjittofi; Styliana Charalambous; Ioannis Pashalidis

2016-01-01

The efficiency of activated biochar fibres obtained fromOpuntia Ficus Indica regarding the sorption of trivalent samarium (Sm(III)) from aqueous solutions was investigated by batch experiments. The effect of various physicochemical parameters (e.g. pH, initial metal concentration, ionic strength, temperature and contact time) on the Sm(III) adsorption was studied and the surface species were characterized by FTIR spectroscopy prior to and after the lanthanide sorption. The experimental results showed that the acti-vated biochar fibres possessed extraordinary sorption capacity for Sm(III) in acidic solutions (qmax=90 g/kg, pH 3.0) and near neutral solutions (qmax=350 g/kg, pH 6.5). This was attributed to the formation of samarium complexes with the surface carboxylic moieties, available in high density on the lamellar structures of the bio-sorbent.

Pressure and irradiation effects on transport properties of samarium compounds with instable valence

International Nuclear Information System (INIS)

Morillo, J.

1981-01-01

Electron transport properties in samarium compounds with instable valence are studied in this thesis: from SmS in its integer valence phases at common pressure to SmB 6 compound IV at common pressure through SmSsub(1-x)Psub(x) (x 6 is presented [fr

Graphite furnace atomic absorption spectrometry with a tantalum boat for the determination of yttrium, samarium, and dysprosium in a mish metal

International Nuclear Information System (INIS)

Daidoji, Hidehiro; Tamura, Shohei

1982-01-01

The determination of yttrium, samarium, and dysprodium by means of graphite-furnace atomic absorption spectrometry (AAS) was studied by a tantalum boat inserted into a graphite tube atomizer. These elements could not be determined by the use of a commercial graphite tube, In the atomization from a tantalum boat, better analytical sensitivities and negligible memory effects for these rare earths are obtained. The analytical sensitivities of yttrium, samarium, and dysprodium with the tantalum boat were 0.60 ng, 0.86 ng, and 0.17 ng respectively. This method was applied for the determination of yttrium, samarium, and dysprosium in a mish metal. The measurements were performed with slightly acidified solutions (0.01 mol dm 3 HCI or HNO 3 ). The sensitivities and the precisions for these elements decreased with increasing acid concentration. An enhancement in the sensitivities of yttrium and dysprosium upon the addition of a large excess of lanthanum, neodymium, and praseodymium salts were observed. The yttrium, samarium, and dysprosium in a mish metal were determined with both analytical curves of standard solutions containing an excess of lanthanum, cerium, and neodymium ions and of the standard addition. The precisions for this work were in the 3 - 9.3% range. (author)

Polypyrrole-coated samarium oxide nanobelts: fabrication, characterization, and application in supercapacitors

Science.gov (United States)

Liu, Peng; Wang, Yunjiao; Wang, Xue; Yang, Chao; Yi, Yanfeng

2012-11-01

Polypyrrole-coated samarium oxide nanobelts were synthesized by the in situ chemical oxidative surface polymerization technique based on the self-assembly of pyrrole on the surface of the amine-functionalized Sm2O3 nanobelts. The morphologies of the polypyrrole/samarium oxide (PPy/Sm2O3) nanocomposites were characterized using transmission electron microscope. The UV-vis absorbance of these samples was also investigated, and the remarkable enhancement was clearly observed. The electrochemical behaviors of the PPy/Sm2O3 composites were investigated by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge-discharge. The results indicated that the PPy/Sm2O3 composite electrode was fully reversible and achieved a very fast Faradaic reaction. After being corrected into the weight percentage of the PPy/Sm2O3 composite at a current density of 20 mA cm-2 in a 1.0 M NaNO3 electrolyte solution, a maximum discharge capacity of 771 F g-1 was achieved in a half-cell setup configuration for the PPy/Sm2O3 composites electrode with the potential application to electrode materials for electrochemical capacitors.

Peculiarities of electronic, phonon and magnon subsystems of lanthanum and samarium tetraborides

Energy Technology Data Exchange (ETDEWEB)

Novikov, V.V., E-mail: vvnovikov@mail.ru; Mitroshenkov, N.V.; Matovnikov, A.V.

2015-10-15

Experimental research was carried out to study the temperature dependences of heat capacity C{sub p}(T = 2–300 K), lattice parameters a(T), and ≿(T), (5–300 K) of lanthanum and samarium tetraborides. A comparison with data obtained previously for LuB{sub 4} reveals the peculiar influence of lanthanide contraction and the rare-earths mass on the thermodynamic properties of rare earth tetraborides at low and high temperatures. Sharp anomalies were found in the heat capacity and thermal expansion for SmB{sub 4} at T{sub N} = 25.1 K, conditioned by the phase transition into antiferromagnetic state. The more poorly defined heat capacity anomaly around 7 K is referred to the quadrupole orbital fluctuation of the atomic magnetic moments for Sm{sup 3+} ions. The electronic, lattice, and magnetic contributions to the heat capacity and thermal expansion of samarium tetraboride were defined. Our approach makes it possible to adequately approximate the lattice components of heat capacity and thermal expansion by combining the Debye and Einstein contributions, which are based on the joint analysis of calorimetric and X-ray data. The influence of the frustration of the atomic magnetic moment system for Sm{sup 3+} ions on the thermodynamic characteristics of the samarium tetraboride magnetic phase transition was revealed. - Highlights: • The heat capacity and lattice parameters for LaB{sub 4} and SmB{sub 4} were determined at 2–300 K. • The anomalies of C{sub p}(T), a(T), c(T) for SmB{sub 4} due to the phase transition are revealed. • The lattice contributions to the thermal properties of LaB{sub 4} and SmB{sub 4} are analyzed.

Australian manufacture of QuadrametTM (Samarium-153 EDTMP)

International Nuclear Information System (INIS)

Wood, N.R.; Whitwell, J.

1997-01-01

Quadramet T (Samarium-153 EDTMP) has been shown overseas to be potentially useful in the palliation of painful osteoblastic skeletal metastases and has been approved this year for general marketing in the USA. Australian Radioisotopes (ARI) has licensed this product from the Australian patent holders, Dow Chemical. Within the facilities of ARI, a hot cell has been dedicated to this product and fitted out to manufacture it weekly on a cycle related to the operating cycle of the Australian reactor HIFAR. Due to neutron flux limitations of HIFAR, the local formulation has an elemental Samarium content up to 200μg/mL whereas the overseas formulation has a level of 20-46μg/mL. All other specifications of the two products are essentially the same. In 1995 and 1996 a small clinical trial with 19 patients was held which demonstrated that the pharmacokinetic behaviour was also essentially the same by measuring blood clearance rates and skeletal uptake dynamics. Soft tissue uptake was also qualitatively determined. The ARI version is now the subject of an application for general marketing within Australia. Some useful characteristics of this agent are: almost complete excretion or fixation in the skeleton within 6 hours, rapid onset of clinical effect, applicability in most cases where an abnormal diagnostic bone scan correlates with painful sites, dosage can be tailored to individual patient uptake due to easy dose measurement and retreatment is quite possible. The use of this class of agents in pain palliation continues to increase. Australian manufacture of Quadramet TM provides a further option in the management of these difficult cases

Calcium hydroxide poisoning

Science.gov (United States)

Hydrate - calcium; Lime milk; Slaked lime ... Calcium hydroxide ... These products contain calcium hydroxide: Cement Limewater Many industrial solvents and cleaners (hundreds to thousands of construction products, flooring strippers, brick cleaners, cement ...

Sodium hydroxide poisoning

Science.gov (United States)

Sodium hydroxide is a very strong chemical. It is also known as lye and caustic soda. This ... poisoning from touching, breathing in (inhaling), or swallowing sodium hydroxide. This article is for information only. Do ...

Polypyrrole-coated samarium oxide nanobelts: fabrication, characterization, and application in supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Liu Peng, E-mail: pliu@lzu.edu.cn; Wang Yunjiao; Wang Xue; Yang Chao; Yi Yanfeng [College of Chemistry and Chemical Engineering, Lanzhou University, Key Laboratory of Nonferrous Metal Chemistry and Resources Utilization of Gansu Province and State Key Laboratory of Applied Organic Chemistry (China)

2012-11-15

Polypyrrole-coated samarium oxide nanobelts were synthesized by the in situ chemical oxidative surface polymerization technique based on the self-assembly of pyrrole on the surface of the amine-functionalized Sm{sub 2}O{sub 3} nanobelts. The morphologies of the polypyrrole/samarium oxide (PPy/Sm{sub 2}O{sub 3}) nanocomposites were characterized using transmission electron microscope. The UV-vis absorbance of these samples was also investigated, and the remarkable enhancement was clearly observed. The electrochemical behaviors of the PPy/Sm{sub 2}O{sub 3} composites were investigated by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge-discharge. The results indicated that the PPy/Sm{sub 2}O{sub 3} composite electrode was fully reversible and achieved a very fast Faradaic reaction. After being corrected into the weight percentage of the PPy/Sm{sub 2}O{sub 3} composite at a current density of 20 mA cm{sup -2} in a 1.0 M NaNO{sub 3} electrolyte solution, a maximum discharge capacity of 771 F g{sup -1} was achieved in a half-cell setup configuration for the PPy/Sm{sub 2}O{sub 3} composites electrode with the potential application to electrode materials for electrochemical capacitors.

Production of SmCo5 alloy by calciothermic reduction of samarium oxide

International Nuclear Information System (INIS)

Krishnan, T.S.; Gupta, C.K.

1988-01-01

Among the established permanent magnets, SmCo 5 magnet occupies the foremost position as it offers a unique combination of high energy product, coercivity and curie temperature. The SmCo 5 magnets are thus extensively used for high field applications. These are also best suited for use in environments where high demagnetizing field and high temperature are operative. Also, for applications where high performance and miniaturization are the over-riding considerations, the choice again falls on SmCo 5 magnets. The main deterrent to the widespread use of SmCo 5 magnet is its high cost. Both samarium and cobalt metals are high priced, and the magnets prepared from their directly melted alloy are thus naturally very expensive. An alternate process involving calcium reduction of their oxide intermediates has, therefore, been studied and the alloy prepared by this process has been evaluated and found satisfactory for magnet production. The process essentially involves compaction of the charge mix containing samarium oxide, cobalt oxide (or metal) and calcium metal and reduction of the charge compact at 1000-1300 degrees C in hydrogen atmosphere, followed by water and acid leaching, drying and classification

Samarium oxide as a radiotracer to evaluate the in vivo biodistribution of PLGA nanoparticles

CSIR Research Space (South Africa)

Mandiwana, V

2015-09-01

Full Text Available the biodistribution of poly(D,L-lactide-co-glycolide) (PLGA) nanoparticles containing samarium-153 oxide ([(sup153)Sm]Sm(sub2)O(sub3)) in vivo to prove that orally administered nanoparticles alter the biodistribution of a drug. These were then activated in a nuclear...

Neutron Capture and Transmission Measurements and Resonance Parameter Analysis of Samarium

International Nuclear Information System (INIS)

Leinweber, G.; Burke, J.A.; Knox, H.D.; Drindak, N.J.; Mesh, D.W.; Haines, W.T.; Ballad, R.V.; Block, R.C.; Slovacek, R.E.; Werner, C.J.; Trbovich, M.J.; Barry, D.P.; Sato, T.

2001-01-01

The purpose of the present work is to accurately measure the neutron cross sections of samarium. The most significant isotope is 149 Sm, which has a large neutron absorption cross section at thermal energies and is a 235 U fission product with a 1% yield. Its cross sections are thus of concern to reactor neutronics. Neutron capture and transmission measurements were performed by the time-of-flight technique at the Rensselaer Polytechnic institute (RPI) LINAC facility using metallic and liquid Sm samples. The capture measurements were made at the 25 meter flight station with a multiplicity-type capture detector, and the transmission total cross-section measurements were performed at 15- and 25-meter flight stations with 6 Li glass scintillation detectors. Resonance parameters were determined by a combined analysis of six experiments (three capture and three transmission) using the multi-level R-matrix Bayesian code SAMMY version M2. The significant features of this work are as follows. Dilute samples of samarium nitrate in deuterated water (D 2 O) were prepared to measure the strong resonances at 0.1 and 8 eV without saturation. Disk-shaped spectroscopic quartz cells were obtained with parallel inner surfaces to provide a uniform thickness of solution. The diluent feature of the SAMMY program was used to analyze these data. The SAMMY program also includes multiple scattering corrections to capture yield data and resolution functions specific to the RPI facility. Resonance parameters for all stable isotopes of samarium were deduced for all resonances up to 30 eV. Thermal capture cross-section and capture resonance integral calculations were made using the resultant resonance parameters and were compared to results obtained using resonance parameters from ENDF/B-VI updated through release 3. Extending the definition of the capture resonance integral to include the strong 0.1 eV resonance in 149 Sm, present measurements agree within estimated uncertainties with En

Identification of the lines in the L emission spectrum of cerium and samarium

International Nuclear Information System (INIS)

Shrivastava, B.D.; Singh, D.

1992-01-01

The occurrence of a line at 2.1556 A in the L emission spectrum of cerium and two lines at 1.6679 and 1.8379 A in the L emission spectrum of samarium, reported many years ago, has remained a puzzle. These have now been identified as EXAFS minima occurring at the L absorption edges of the respective elements. (author)

21 CFR 184.1631 - Potassium hydroxide.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Potassium hydroxide. 184.1631 Section 184.1631 Food... Specific Substances Affirmed as GRAS § 184.1631 Potassium hydroxide. (a) Potassium hydroxide (KOH, CAS Reg... pellets, flakes, sticks, lumps, and powders. Potassium hydroxide is obtained commercially from the...

Samarium-153-EDTMP in the metastatic bone pain treatment

International Nuclear Information System (INIS)

Lins Filho, M.L.M.; Santos, A.O.; Nappi, A.P.B.; Meirelles, M.B.; Arouca, P.T.; Ramos, C.D.; Etchebehere, E.C.S.C.; Teixeira, L.C.; Netto Junior, N.R.; D'Ancona Cal; Camargo, E.E.

1997-01-01

Full text: Bone metastasis is the most reason of pain in prostate and mammary cancer patients. The Samarium-153-EDTMP has been showed as an alternative to the treatment of the metastasis bone pain. With the objective to evaluate the use of the Sm-153-EDTMP as a systemic therapy for the metastasis bone pain, 30 patients (19 male, 11 female, average age of 64,5 years) were studied. 19 patients with prostate cancer and 11 with mammary cancer. All the patients presented previous bone scintiscanning with multiple metastasis; interruption of the chemotherapy or radiotherapy for two or more weeks and leukocyte count higher than 2,000 leukocytes/mm 3 and platelets higher than 80,000/mm 3 . The patients were classified previously to the radioisotope therapy, as far the intensity of the pain in a scale from 0 to 10 is concerned. All the patients received 37 MBq/kg (1m Ci/kg) of weight of Sm-153-EDTMP by venous via. The evaluation 6 weeks after the therapy showed complete or partial pain relief in 22 patients (73,3%). Complete or partial pain relief has been obtained in 91,0% (10 in 11) of the patients with mammary cancer and in 62,2% (12 in 19) of the patients with prostate cancer. Transitory leukopenia (lower than 2,000 leukocytes/mm 3 ) and platelet count (lower than 80,000/mm 3 ) occurred in 33,3% of the patients. 8 patients (26,7%) did not responded to the therapy. The therapy with Samarium-153-EDTMP is a simple, safe and efficient method in the treatment of the bone pain caused by metastasis

Dependence of samarium-soil interaction on samarium concentration: Implications for environmental risk assessment.

Science.gov (United States)

Ramírez-Guinart, Oriol; Salaberria, Aitor; Vidal, Miquel; Rigol, Anna

2018-03-01

The sorption and desorption behaviour of samarium (Sm), an emerging contaminant, was examined in soil samples at varying Sm concentrations. The obtained sorption and desorption parameters revealed that soil possessed a high Sm retention capacity (sorption was higher than 99% and desorption lower than 2%) at low Sm concentrations, whereas at high Sm concentrations, the sorption-desorption behaviour varied among the soil samples tested. The fractionation of the Sm sorbed in soils, obtained by sequential extractions, allowed to suggest the soil properties (pH and organic matter solubility) and phases (organic matter, carbonates and clay minerals) governing the Sm-soil interaction. The sorption models constructed in the present work along with the sorption behaviour of Sm explained in terms of soil main characteristics will allow properly assessing the Sm-soil interaction depending on the contamination scenario under study. Moreover, the sorption and desorption K d values of radiosamarium in soils were strongly correlated with those of stable Sm at low concentrations (r = 0.98); indicating that the mobility of Sm radioisotopes and, thus, the risk of radioactive Sm contamination can be predicted using data from low concentrations of stable Sm. Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermomechanical behavior of Fe-Mn-Si-Cr-Ni shape memory alloys modified with samarium

International Nuclear Information System (INIS)

Shakoor, R.A.; Khalid, F. Ahmad

2009-01-01

The deformation and training behavior of Fe-14Mn-3Si-10Cr-5Ni (wt.%) shape memory alloys containing samarium addition has been studied in the iron-based shape memory alloys. It is noticed that thermomechanical treatment (training) has significant influence on proof stress, critical stress and shape memory behavior of the alloys. The improvement in shape memory behavior can be attributed to the decrease in the proof stress and critical stress which facilitates the formation of ε (hcp martensite). It is also observed that alloy 2 containing samarium undergoes less softening as compared to alloy 1 with training which inhibits the formation of α (bcc martensite) and thus enhances the shape memory behavior. The excessive thermomechanical treatment with increase in the training cycle has led to the formation of α (bcc martensite) along with ε (hcp martensite) in the alloy 1 which appeared to have decline in the shape memory effect. This has been demonstrated by the examination of microstructure and identification of α (bcc martensite) martensite in the alloy 1 as compared to alloy 2

Effective visible light-active nitrogen and samarium co-doped BiVO4 for the degradation of organic pollutants

International Nuclear Information System (INIS)

Wang, Min; Niu, Chao; Liu, Jun; Wang, Qianwu; Yang, Changxiu; Zheng, Haoyan

2015-01-01

Nitrogen and samarium co-doped BiVO 4 (N–xSm–BiVO 4 ) nanoparticles were synthesized using a sol–gel method with a corn stem template. The physicochemical properties of the resultant N–xSm–BiVO 4 particles were characterized using various methods: XPS, XRD, SEM, BET, and UV–Vis DRS analyses. The visible-light photocatalytic activity was successfully demonstrated by degrading a model dye, namely, methyl orange. The dopant content was optimized, and the nitrogen and samarium co-doped BiVO 4 extended the light absorption spectrum toward the visible region, significantly enhancing the photodegradation of the model dye. The Sm and N co-doped BiVO 4 exhibited the highest photocatalytic activity compared to materials with a single dopant or no dopant. The significantly enhanced photocatalytic activity of the N–Sm co-doped BiVO 4 under visible-light irradiation can be attributed to the synergistic effects of the nitrogen and samarium. - Highlights: • The N–Sm codoped BiVO 4 were synthesized using a sol–gel method with a corn stem template. • The N and Sm codoped BiVO 4 has excellent photocatalytic activity of methyl orange degradation. • The maximum activity was observed when the molar ratio of Sm/Bi was 1.0. • The high photocatalytic activity was caused by the synergistic effects between N doping and Sm doping

Formation of mixed hydroxides in the thorium chloride-iron chloride-sodium hydroxide system

International Nuclear Information System (INIS)

Krivokhatskij, A.S.; Prokudina, A.F.; Sapozhnikova, T.V.

1976-01-01

The process of formation of mixed hydroxides in the system thorium chloride-iron chloride-NaOH was studied at commensurate concentrations of Th and Fe in solution (1:1 and 1:10 mole fractions, respectively) with ionic strength 0.3, 2.1, and 4.1, created with the electrolyte NaCl, at room temperature 22+-1degC. By the methods of chemical, potentiometric, thermographic, and IR-spectrometric analyses, it was shown that all the synthesized precipitates are mechanical mixtures of two phases - thorium hydroxide and iron hydroxide - and not a new hydrated compound. The formal solubility of the precipitates of mixed hydroxides was determined. It was shown that the numerical value of the formal solubility depends on the conditions of formation and age of the precipitates

Electrochemical extraction of samarium from molten chlorides in pyrochemical processes

International Nuclear Information System (INIS)

Castrillejo, Y.; Fernandez, P.; Medina, J.; Hernandez, P.; Barrado, E.

2011-01-01

This work concerns the electrochemical extraction of samarium from molten chlorides. In this way, the electrochemical behaviour of samarium ions has been investigated in the eutectic LiCl-KCl at the surface of tungsten, aluminium and aluminium coated tungsten electrodes. On a W inert electrode the electro-reduction of Sm(III) takes place in only one soluble-soluble electrochemical step Sm(III)/Sm(II). The electrochemical system Sm(II)/Sm(0) has not been observed within the electrochemical window, because of the prior reduction of Li(I) ions from the solvent, which inhibits the electro-extraction of Sm species from the salt on such a substrate. Sm metal in contact with the melt react to give Li(0) according to the reaction: Sm(0) + 2Li(I) ↔ Sm(II) + 2Li(0). On the contrary, on reactive Al electrodes the electrochemical system Sm(II)/Sm(0) was observed within the electroactive range. The potential shift of the redox couple is caused by the decrease of Sm activity in the metal phase due to the formation of Sm-Al alloys at the interface. The formation mechanism of the intermetallic compounds was studied in a melt containing: (i) both Sm(III) and Al(III) ions, using W and Al coated tungsten electrodes, and (ii) Sm(III) ions using an Al electrode. Analysis of the samples after potentiostatic electrolysis by X-ray diffraction and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS), allowed the identification of Al 3 Sm and Al 2 Sm.

Electrochemical extraction of samarium from molten chlorides in pyrochemical processes

Energy Technology Data Exchange (ETDEWEB)

Castrillejo, Y., E-mail: ycastril@qa.uva.es [QUIANE/Dept Quimica Analitica, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain); Fernandez, P. [QUIANE/Dept Quimica Analitica, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain); Medina, J. [Dept Fisica Materia Condensada Cristalografia y Mineralogia, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain); Hernandez, P. [Centro de Investigaciones Quimicas, Universidad Autonoma del Estado de Hidalgo, Carr. Pachuca-Tulancingo Km. 4.5, C.P. 42076 Pachuca, Hidalgo (Mexico); Barrado, E. [QUIANE/Dept Quimica Analitica, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain)

2011-10-01

This work concerns the electrochemical extraction of samarium from molten chlorides. In this way, the electrochemical behaviour of samarium ions has been investigated in the eutectic LiCl-KCl at the surface of tungsten, aluminium and aluminium coated tungsten electrodes. On a W inert electrode the electro-reduction of Sm(III) takes place in only one soluble-soluble electrochemical step Sm(III)/Sm(II). The electrochemical system Sm(II)/Sm(0) has not been observed within the electrochemical window, because of the prior reduction of Li(I) ions from the solvent, which inhibits the electro-extraction of Sm species from the salt on such a substrate. Sm metal in contact with the melt react to give Li(0) according to the reaction: Sm(0) + 2Li(I) {r_reversible} Sm(II) + 2Li(0). On the contrary, on reactive Al electrodes the electrochemical system Sm(II)/Sm(0) was observed within the electroactive range. The potential shift of the redox couple is caused by the decrease of Sm activity in the metal phase due to the formation of Sm-Al alloys at the interface. The formation mechanism of the intermetallic compounds was studied in a melt containing: (i) both Sm(III) and Al(III) ions, using W and Al coated tungsten electrodes, and (ii) Sm(III) ions using an Al electrode. Analysis of the samples after potentiostatic electrolysis by X-ray diffraction and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS), allowed the identification of Al{sub 3}Sm and Al{sub 2}Sm.

Resonances of coherent population trapping in samarium vapours

International Nuclear Information System (INIS)

Kolachevsky, Nikolai N; Akimov, A V; Kiselev, N A; Papchenko, A A; Sorokin, Vadim N; Kanorskii, S I

2001-01-01

Resonances of coherent population trapping were detected in atomic vapours of the rare-earth element samarium. The coherent population trapping was produced by two external-cavity diode lasers (672 and 686 nm) in a Λ-system formed by the three levels of 154 Sm: the 4f 6 6s 2 ( 7 F 0 ) ground state, the first fine-structure 4f 6 6s 2 ( 7 F 1 ) sublevel of the ground state and the 4f 6 ( 7 F)6s6p( 3 P o ) 9 F o 1 upper level. The dependence of the spectral shapes and resonance contrasts on the polarisation of the laser beams and the direction of the applied magnetic field was studied. The obtained results were analysed. (nonlinear optical phenomena)

The systems lanthanum (cerium, samarium) nitrate-tetramethyl-ammonium nitrate-water

International Nuclear Information System (INIS)

Zhuravlev, E.F.; Khisaeva, D.A.; Semenova, Eh.B.

1984-01-01

The method of cross sections at 25 and 50 deg C has been applied to study solubility in the systems lanthanum nitrate-tetramethyl ammonium nitrate-water (1), cesium (3) nitrate-tetramethyl ammonium nitrate-water (2) and samarium nitrate-tetramethyl ammonium nitrate-water (3). Crystallization fields of congruently dissolving compounds with 1:3 ratio of salt components (in system 1) and 1:2 ratio (in systems 2 and 3) are found in the systems. New solid phases are separated preparatively and subjected to chemical, differential thermal and IR spectroscopic analyses. Compositions of formed compounds are compared with the compositions known for nitrates of other representatives of light lanthanides

21 CFR 582.1631 - Potassium hydroxide.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Potassium hydroxide. 582.1631 Section 582.1631 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1631 Potassium hydroxide. (a) Product. Potassium hydroxide. (b) Conditions of use. This...

The systems cerium(3) (samarium) nitrate-quinoline nitrate-water

International Nuclear Information System (INIS)

Khisaeva, D.A.; Zhuravlev, E.F.; Semenova, Eh.B.

1982-01-01

Using the method of cross sections at 25 and 50 deg C the solubility in the systems cerium (3) nitrate-quinoline nitrate-water and samarium nitrate-quinoline nitrate-water has been studied. It is established that in the systems during chemical interaction of components congruently melting compounds of the composition: Ce(NO 3 ) 2 x2[C 9 H 7 NxHNO 3 ]x6H 2 O and Sm(NO 3 ) 3 x2[C 9 H 7 NxHNO 3 ]x2H 2 O are formed. New solid phases are separated preparatively and are subjected to chemical, differential thermal and IR spectroscopic analyses. The investigation results are compared with similar ones for nitrates of other representatives of lanthanide group

Body composition analysis by DEXA by using dynamically changing samarium filtration

DEFF Research Database (Denmark)

Gotfredsen, Arne; Baeksgaard, L; Hilsted, J

1997-01-01

Dual-energy X-ray absorptiometry (DEXA) has a high accuracy for body composition analysis but is influenced by beam hardening and other error sources in the extremes of measurement. To compensate for beam hardening, the Norland XR-36 introduces a dynamically changing samarium filtration system......). Scans of six healthy volunteers covered with combinations of beef and lard (approximately 5-15 kg) showed a good agreement (r = 0.99) between reference and DEXA values of added soft tissue mass and fat percentage. We conclude that the DEXA method (and, in particular, the Norland XR-36 using dynamic...

Effective visible light-active nitrogen and samarium co-doped BiVO{sub 4} for the degradation of organic pollutants

Energy Technology Data Exchange (ETDEWEB)

Wang, Min; Niu, Chao [College of Environmental and Chemical Engineering, Shenyang Ligong University, Shenyang 110165 (China); Liu, Jun, E-mail: minwang62@msn.com [Shenyang Military General Hospital, Shenyang 110016 (China); Wang, Qianwu; Yang, Changxiu; Zheng, Haoyan [College of Environmental and Chemical Engineering, Shenyang Ligong University, Shenyang 110165 (China)

2015-11-05

Nitrogen and samarium co-doped BiVO{sub 4} (N–xSm–BiVO{sub 4}) nanoparticles were synthesized using a sol–gel method with a corn stem template. The physicochemical properties of the resultant N–xSm–BiVO{sub 4} particles were characterized using various methods: XPS, XRD, SEM, BET, and UV–Vis DRS analyses. The visible-light photocatalytic activity was successfully demonstrated by degrading a model dye, namely, methyl orange. The dopant content was optimized, and the nitrogen and samarium co-doped BiVO{sub 4} extended the light absorption spectrum toward the visible region, significantly enhancing the photodegradation of the model dye. The Sm and N co-doped BiVO{sub 4} exhibited the highest photocatalytic activity compared to materials with a single dopant or no dopant. The significantly enhanced photocatalytic activity of the N–Sm co-doped BiVO{sub 4} under visible-light irradiation can be attributed to the synergistic effects of the nitrogen and samarium. - Highlights: • The N–Sm codoped BiVO{sub 4} were synthesized using a sol–gel method with a corn stem template. • The N and Sm codoped BiVO{sub 4} has excellent photocatalytic activity of methyl orange degradation. • The maximum activity was observed when the molar ratio of Sm/Bi was 1.0. • The high photocatalytic activity was caused by the synergistic effects between N doping and Sm doping.

Ferrites Ni0,5Zn0,5Fe2O4 doped with samarium: structural analysis, morphological and electromagnetic

International Nuclear Information System (INIS)

Costa, A.C.F.M.; Diniz, A.P.; Viana, K.M.S.; Cornejo, D.R.; Kiminami, R.H.G.A.

2010-01-01

This paper proposes to investigate the sintering at 1200 deg C/2h of Ni 0.5 Zn 0.5 Fe 2-x Sm x O 4 ferrite doped with 0.05; 0.075 e 0.1 mol of Sm synthesized by combustion reaction to evaluate the performance materials as absorbers of electromagnetic radiation. The influence of the concentration of samarium on the structure, morphology and electromagnetic properties of ferrites was studied. The resulting samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), magnetic measurements and reflectivity measurements in the frequency range between 8-12 GHz. The results showed that increasing the concentration of samarium caused a decrease in particle size of the samples, encouraging, therefore, to obtain materials with better values of magnetization and reflectivity, allowing for use as absorbers in narrow-band frequency between 9-10 GHz. (author)

Structural transformation of nickel hydroxide films during anodic oxidation

Energy Technology Data Exchange (ETDEWEB)

Crocker, Robert W. [Univ. of California, Berkeley, CA (United States); Muller, Rolf H. [Univ. of California, Berkeley, CA (United States)

1992-05-01

The transformation of anodically formed nickel hydroxide/oxy-hydroxide electrodes has been investigated. A mechanism is proposed for the anodic oxidation reaction, in which the reaction interface between the reduced and oxidized phases of the electrode evolves in a nodular topography that leads to inefficient utilization of the active electrode material. In the proposed nodular transformation model for the anodic oxidation reaction, nickel hydroxide is oxidized to nickel oxy-hydroxide in the region near the metal substrate. Since the nickel oxy-hydroxide is considerably more conductive than the surrounding nickel hydroxide, as further oxidation occurs, nodular features grow rapidly to the film/electrolyte interface. Upon emerging at the electrolyte interface, the reaction boundary between the nickel hydroxide and oxy-hydroxide phases spreads laterally across the film/electrolyte interface, creating an overlayer of nickel oxy-hydroxide and trapping uncharged regions of nickel hydroxide within the film. The nickel oxy-hydroxide overlayer surface facilitates the oxygen evolution side reaction. Scanning tunneling microscopy of the electrode in its charged state revealed evidence of 80 - 100 Angstrom nickel oxy-hydroxide nodules in the nickel hydroxide film. In situ spectroscopic ellipsometer measurements of films held at various constant potentials agree quantitatively with optical models appropriate to the nodular growth and subsequent overgrowth of the nickel oxy-hydroxide phase. A two-dimensional, numerical finite difference model was developed to simulate the current distribution along the phase boundary between the charged and uncharged material. The model was used to explore the effects of the physical parameters that govern the electrode behavior. The ratio of the conductivities of the nickel hydroxide and oxy-hydroxide phases was found to be the dominant parameter in the system.

Structural transformation of nickel hydroxide films during anodic oxidation

Energy Technology Data Exchange (ETDEWEB)

Crocker, R.W.; Muller, R.H.

1992-05-01

The transformation of anodically formed nickel hydroxide/oxy-hydroxide electrodes has been investigated. A mechanism is proposed for the anodic oxidation reaction, in which the reaction interface between the reduced and oxidized phases of the electrode evolves in a nodular topography that leads to inefficient utilization of the active electrode material. In the proposed nodular transformation model for the anodic oxidation reaction, nickel hydroxide is oxidized to nickel oxy-hydroxide in the region near the metal substrate. Since the nickel oxy-hydroxide is considerably more conductive than the surrounding nickel hydroxide, as further oxidation occurs, nodular features grow rapidly to the film/electrolyte interface. Upon emerging at the electrolyte interface, the reaction boundary between the nickel hydroxide and oxy-hydroxide phases spreads laterally across the film/electrolyte interface, creating an overlayer of nickel oxy-hydroxide and trapping uncharged regions of nickel hydroxide within the film. The nickel oxy-hydroxide overlayer surface facilitates the oxygen evolution side reaction. Scanning tunneling microscopy of the electrode in its charged state revealed evidence of 80 {endash} 100 Angstrom nickel oxy-hydroxide nodules in the nickel hydroxide film. In situ spectroscopic ellipsometer measurements of films held at various constant potentials agree quantitatively with optical models appropriate to the nodular growth and subsequent overgrowth of the nickel oxy-hydroxide phase. A two-dimensional, numerical finite difference model was developed to simulate the current distribution along the phase boundary between the charged and uncharged material. The model was used to explore the effects of the physical parameters that govern the electrode behavior. The ratio of the conductivities of the nickel hydroxide and oxy-hydroxide phases was found to be the dominant parameter in the system.

Dissolution mechanism of aluminum hydroxides in acid media

Science.gov (United States)

Lainer, Yu. A.; Gorichev, I. G.; Tuzhilin, A. S.; Gololobova, E. G.

2008-08-01

The effects of the concentration, temperature, and potential at the hydroxide/electrolyte interface on the aluminum hydroxide dissolution in sulfuric, hydrochloric, and perchloric acids are studied. The limiting stage of the aluminum hydroxide dissolution in the acids is found to be the transition of the complexes that form on the aluminum hydroxide surface from the solid phase into the solution. The results of the calculation of the acid-base equilibrium constants at the oxide (hydroxide)/solution interface using the experimental data on the potentiometric titration of Al2O3 and AlOOH suspensions are analyzed. A mechanism is proposed for the dissolution of aluminum hydroxides in acid media.

Nickel-cobalt hydroxide nanosheets: Synthesis, morphology and electrochemical properties.

Science.gov (United States)

Schneiderová, Barbora; Demel, Jan; Zhigunov, Alexander; Bohuslav, Jan; Tarábková, Hana; Janda, Pavel; Lang, Kamil

2017-08-01

This paper reports the synthesis, characterization, and electrochemical performance of nickel-cobalt hydroxide nanosheets. The hydroxide nanosheets of approximately 0.7nm thickness were prepared by delamination of layered nickel-cobalt hydroxide lactate in water and formed transparent colloids that were stable for months. The nanosheets were deposited on highly oriented pyrolytic graphite by spin coating, and their electrochemical behavior was investigated by cyclic voltammetry in potassium hydroxide electrolyte. Our method of electrode preparation allows for studying the electrochemistry of nanosheets where the majority of the active centers can participate in the charge transfer reaction. The observed electrochemical response was ascribed to mutual compensation of the cobalt and nickel response via electron sharing between these metals in the hydroxide nanosheets, a process that differentiates the behavior of nickel-cobalt hydroxide nanosheets from single nickel hydroxide or cobalt hydroxide nanosheets or their physical mixture. The presence of cobalt in the nickel-cobalt hydroxide nanosheets apparently decreases the time of electrochemical activation of the nanosheet layer, which for the nickel hydroxide nanosheets alone requires more potential sweeps. Copyright © 2017 Elsevier Inc. All rights reserved.

21 CFR 73.2326 - Chromium hydroxide green.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium hydroxide green. 73.2326 Section 73.2326... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2326 Chromium hydroxide green. (a) Identity and specifications.The color additive chromium hydroxide green shall conform in identity and specifications to the...

Determination of micro amounts of samarium and europium by analogue derivative spectrophotometry

International Nuclear Information System (INIS)

Ishii, H.; Satoh, K.

1982-01-01

Derivative spectrophotometry using the analogue differentiation circuit was applied to the determination of samarium and europium at ppm levels. By measuring the second or the fourth derivative spectra of the characteristic absorption bands of both the rare earth ions around 400 nm, they can be determined directly and selectively in the presence of large amounts of most other rare earths without any prior separation. Further, aptly selecting conditions for the measurement of the derivative spectra, the simultaneous determination of both the rare earth elements was feasible. The principle and the characteristics of analogue derivative spectrophotometry are also described. (orig.) [de

21 CFR 73.1326 - Chromium hydroxide green.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium hydroxide green. 73.1326 Section 73.1326... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1326 Chromium hydroxide green. (a) Identity. (1) The color additive chromium hydroxide green is principally hydrated chromic sesquioxide (Cr2O3·XH2O...

Analysis of barium hydroxide and calcium hydroxide slurry carbonation reactors

International Nuclear Information System (INIS)

Patch, K.D.; Hart, R.P.; Schumacher, W.A.

1980-05-01

The removal of CO 2 from air was investigated by using a continuous-agitated-slurry carbonation reactor containing either barium hydroxide [Ba(OH) 2 ] or calcium hydroxide [Ca(OH) 2 ]. Such a process would be applied to scrub 14 CO 2 from stack gases at nuclear-fuel reprocessing plants. Decontamination factors were characterized for reactor conditions which could alter hydrodynamic behavior. An attempt was made to characterize reactor performance with models assuming both plug flow and various degrees of backmixing in the gas phase. The Ba(OH) 2 slurry enabled increased conversion, but apparently the process was controlled under some conditions by phenomena differing from those observed for carbonation by Ca(OH) 2 . Overall reaction mechanisms are postulated

New reduced variant in gadolinium and samarium monoxide thin films

Energy Technology Data Exchange (ETDEWEB)

Bist, B M.S.; Kumar, J; Srivastava, O N [Banaras Hindu Univ. (India). Dept. of Physics

1977-01-01

A new reduced phase has been observed in the thin films of gadolinium and samarium monoxides. This phase results on imparting an annealing treatment to the monoxides and is formed as a result of the creation and ordering of vacancies in the oxygen sublattice. The new phase has been analysed to possess a rhombohedral unit cell with lattice parameters a/sub R/ = a/sub 0/ square root of (3/2) and c/sub R/ = a/sub 0/ square root of 3 (based on hexagonal axes, a/sub 0/ being the lattice parameter of the fundamental zinc blende type unit cell of the monoxide). Based on the proposed structure, the new phase can be assigned the solid state chemical formula RO/sub x/ where R = Gd, Sm and x = 0.66.

Phase Composition of Samarium Niobate and Tantalate Thin Films Prepared by Sol-Gel Method

Science.gov (United States)

Bruncková, H.; Medvecký, Ľ.; Múdra, E.; Kovalčiková, A.; Ďurišin, J.; Šebek, M.; Girman, V.

2017-12-01

Samarium niobate SmNbO4 (SNO) and tantalate SmTaO4 (STO) thin films ( 100 nm) were prepared by sol-gel/spin-coating process on alumina substrates with PZT interlayer and annealing at 1000°C. The precursors of films were synthesized using Nb or Ta tartrate complexes. The improvement of the crystallinity of monoclinic M'-SmTaO4 phase via heating was observed through the coexistence of small amounts of tetragonal T-SmTa7O19 phase in STO precursor at 1000°C. The XRD results of SNO and STO films confirmed monoclinic M-SmNbO4 and M'-SmTaO4 phases, respectively, with traces of orthorhombic O-SmNbO4 (in SNO). In STO film, the single monoclinic M'-SmTaO4 phase was revealed. The surface morphology and topography of thin films were investigated by SEM and AFM analysis. STO film was smoother with roughness 3.2 nm in comparison with SNO (6.3 nm). In the microstructure of SNO film, small spherical ( 50 nm) and larger cuboidal particles ( 100 nm) of the SmNbO4 phase were observed. In STO, compact clusters composed of fine spherical SmTaO4 particles ( 20-50 nm) were found. Effect of samarium can contribute to the formation different polymorphs of these films for the application to environmental electrolytic thin film devices.

21 CFR 73.1010 - Alumina (dried aluminum hydroxide).

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Alumina (dried aluminum hydroxide). 73.1010... GENERAL LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1010 Alumina (dried aluminum hydroxide). (a) Identity. (1) The color additive alumina (dried aluminum hydroxide) is a white, odorless...

Evaluation of samarium-153 and holmium-166-EDTMP in the normal baboon model

Energy Technology Data Exchange (ETDEWEB)

Louw, W.K.A.; Dormehl, I.C.; Rensburg, A.J. van; Hugo, N.; Alberts, A.S.; Forsyth, O.E.; Beverley, G.; Sweetlove, M.A.; Marais, J.; Loetter, M.G.; Aswegen, A. van

1996-11-01

Bone-seeking radiopharmaceuticals such as ethylenediaminetetramethylene phosphonate (EDTMP) complexes of samarium-153 and holmium-166 are receiving considerable attention for therapeutic treatment of bone metastases. In this study, using the baboon experimental model, multicompartmental analysis revealed that with regard to pharmacokinetics, biodistribution, and skeletal localisation, {sup 166}Ho-EDTMP was significantly inferior to {sup 153}Sm-EDTMP and {sup 99m}Tc-MDP. A more suitable {sup 166}Ho-bone-seeking agent should thus be sought for closer similarity to {sup 153}Sm-EDTMP to exploit fully the therapeutic potential of its shorter half-life and more energetic beta radiation.

Performance analysis of samarium cobalt P.M. synchronous motor fed from PWM inverters

International Nuclear Information System (INIS)

Rahman, M.A.; Choudhury, M.A.

1985-01-01

This paper presents an analysis and performance of samarium cobalt permanent magnet (P.M.) synchronous motors fed from two types of voltage source pulse width modulated (PWM) inverters. The analysis and test results on the steady state performance of a P.M. motor fed from PWM inverters are presented. PWM inverters are used in variable voltage variable frequency applications to avoid a double conversion process of ordinary inverters. In drives, they are used for voltage and speed regulation of motors. Use of modulation technique in inverters also allow to eliminate or minimize selected harmonics from the inverter output voltage

JAEA thermodynamic database for performance assessment of geological disposal of high-level and TRU wastes. Refinement of thermodynamic data for trivalent actinoids and samarium

International Nuclear Information System (INIS)

Kitamura, Akira; Fujiwara, Kenso; Yui, Mikazu

2010-01-01

Within the scope of the JAEA thermodynamic database project for performance assessment of geological disposal of high-level radioactive and TRU wastes, the refinement of the thermodynamic data for the inorganic compounds and complexes of trivalent actinoids (actinium(III), plutonium(III), americium(III) and curium(III)) and samarium(III) was carried out. Refinement of thermodynamic data for these elements was based on the thermodynamic database for americium published by the Nuclear Energy Agency in the Organisation for Economic Co-operation and Development (OECD/NEA). Based on the similarity of chemical properties among trivalent actinoids and samarium, complementary thermodynamic data for their species expected under the geological disposal conditions were selected to complete the thermodynamic data set for the performance assessment of geological disposal of radioactive wastes. (author)

Oxidation of Dodecanoate Intercalated Iron(II)–Iron(III) Layered Double Hydroxide to Form 2D Iron(III) (Hydr)oxide Layers

DEFF Research Database (Denmark)

Huang, Li‐Zhi; Ayala‐Luis, Karina B.; Fang, Liping

2013-01-01

hydroxide planar layer were preserved during the oxidation, as shown by FTIR spectroscopy. The high positive charge in the hydroxide layer produced by the oxidation of iron(II) to iron(III) is partially compensated by the deprotonation of hydroxy groups, as shown by X‐ray photoelectron spectroscopy...... between the alkyl chains of the intercalated dodecanoate anions play a crucial role in stabilizing the structure and hindering the collapse of the iron(II)–iron(III) (hydr)oxide structure during oxidation. This is the first report describing the formation of a stable planar layered octahedral iron......(III) (hydr)oxide. oxGRC12 shows promise as a sorbent and host for hydrophobic reagents, and as a possible source of single planar layers of iron(III) (hydr)oxide....

21 CFR 872.3250 - Calcium hydroxide cavity liner.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Calcium hydroxide cavity liner. 872.3250 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3250 Calcium hydroxide cavity liner. (a) Identification. A calcium hydroxide cavity liner is a device material intended to be applied to the interior of a...

Retention capacity of samarium (III) in zircon for it possible use in retaining walls for confinement of nuclear residues

International Nuclear Information System (INIS)

Garcia G, N.

2006-01-01

Mexico, as country that produces part of its electric power by nuclear means, should put special emphasis in the development of technologies guided to the sure and long term confinement of the high level nuclear residuals. This work studies the capacity that has the natural zircon to retain to the samarium (III) in solution, by what due, firstly, to characterize the zircon for technical instrumental to determine the purity and characteristic of the mineral in study. The instrumental techniques that were used to carry out the physicochemical characterization were the neutron activation analysis (NAA), the infrared spectroscopy (IS), the thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), semiquantitative analysis, dispersive energy spectroscopy (EDS), X-ray diffraction (XRD) and luminescence technique. The characterization of the surface properties carries out by means of the determination of the surface area using the BET multipoint technique, acidity constants, hydration time, the determination of the point of null charge (pH PCN ) and density of surface sites (D s ). The luminescence techniques were useful to determine the optimal point hydration of the zircon and for the quantification of the samarium, for that here intends the development of both analysis techniques. With the adjustment of the titration curves in the FITEQL 4 package the constants of surface acidity in the solid/liquid interface were determined. To the finish of this study it was corroborated that the zircon is a mineral that presents appropriate characteristics to be proposed as a contention barrier for the deep geologic confinement. With regard to the study of adsorption that one carries out the samarium retention it is superior to 90% under the described conditions. This investigation could also be applicable in the confinement of dangerous industrial residuals. (Author)

Optical properties and electronic transitions of zinc oxide, ferric oxide, cerium oxide, and samarium oxide in the ultraviolet and extreme ultraviolet

DEFF Research Database (Denmark)

Pauly, N; Yubero, F; Espinós, J P

2017-01-01

Optical properties and electronic transitions of four oxides, namely zinc oxide, ferric oxide, cerium oxide, and samarium oxide, are determined in the ultraviolet and extreme ultraviolet by reflection electron energy loss spectroscopy using primary electron energies in the range 0.3-2.0 ke...

Evaluation of layered zinc hydroxide nitrate and zinc/nickel double hydroxide salts in the removal of chromate ions from solutions

International Nuclear Information System (INIS)

Bortolaz de Oliveira, Henrique; Wypych, Fernando

2016-01-01

Layered zinc hydroxide nitrate (ZnHN) and Zn/Ni layered double hydroxide salts were synthesized and used to remove chromate ions from solutions at pH 8.0. The materials were characterized by many instrumental techniques before and after chromate ion removal. ZnHN decomposed after contact with the chromate solution, whereas the layered structure of Zn/Ni hydroxide nitrate (Zn/NiHN) and Zn/Ni hydroxide acetate (Zn/NiHA) remained their layers intact after the topotactic anionic exchange reaction, only changing the basal distances. ZnHN, Zn/NiHN, and Zn/NiHA removed 210.1, 144.8, and 170.1 mg of CrO 4 2− /g of material, respectively. Although the removal values obtained for Zn/NiHN and Zn/NiHA were smaller than the values predicted for the ideal formulas of the solids (194.3 and 192.4 mg of CrO 4 2− /g of material, respectively), the measured capacities were higher than the values achieved with many materials reported in the literature. Kinetic experiments showed the removal reaction was fast. To facilitate the solid/liquid separation process after chromium removal, Zn/Ni layered double hydroxide salts with magnetic supports were also synthesized, and their ability to remove chromate was evaluated. - Highlights: • Zinc hydroxide nitrate and Zn/Ni hydroxide nitrate or acetate were synthesized. • The interlayer anions were replaced by chromate anions at pH=8.0. • Only Zn/Ni hydroxide nitrate or acetate have the structure preserved after exchange. • Fast exchange reaction and high capacity of chromate removal were observed. • Magnetic materials were obtained to facilitate the solids removal the from solutions.

Magnetic behavior study of samarium nitride using density functional theory

Science.gov (United States)

Som, Narayan N.; Mankad, Venu H.; Dabhi, Shweta D.; Patel, Anjali; Jha, Prafulla K.

2018-02-01

In this work, the state-of-art density functional theory is employed to study the structural, electronic and magnetic properties of samarium nitride (SmN). We have performed calculation for both ferromagnetic and antiferromagnetic states in rock-salt phase. The calculated results of optimized lattice parameter and magnetic moment agree well with the available experimental and theoretical values. From energy band diagram and electronic density of states, we observe a half-metallic behaviour in FM phase of rock salt SmN in while metallicity in AFM I and AFM III phases. We present and discuss our current understanding of the possible half-metallicity together with the magnetic ordering in SmN. The calculated phonon dispersion curves shows dynamical stability of the considered structures. The phonon density of states and Eliashberg functional have also been analysed to understand the superconductivity in SmN.

Myelotoxicity of Samarium Sm153 lexidronam in patients with painful bony metastases

International Nuclear Information System (INIS)

Ben Ghachem, T.; Mhiri, A.; Slim, I.; Bahloul, A.; Yeddes, I.; Elbez, I.; Meddeb, I.; Ben Slimene, M.F.

2015-01-01

Full text of publication follows. Introduction: the management of bone pain includes analgesia, radiation, hormones, radiofrequency (RF) ablation, chemotherapy, and surgery. Bone pain palliation therapy with radiopharmaceuticals is a cost-effective systemic therapy to relieve pain from skeletal metastases with a consequent decrease in morbidity and an improvement in quality of life. The aim of our study is to evaluate the effect of myelotoxicity of samarium lexidronam (Sm 153 ) in patients with painful bony metastasis. Methods: we reviewed 116 patients aged from 14 to 87 years old, 91 males (78%) and 25 females (22%), having received 1 to 4 treatments of Sm 153 (37 MBq/kg) for painful bony metastases from different primitive tumors: 67 cases of prostate cancer (57.7%), 22 cases of breast cancer (18.9%), 10 cases of pulmonary cancer (8.6%) and others in 14.6% of cases. Clinical follow-up was available for 159 treatments, consisting on blood count each week over at least two months, in order to evaluate myelotoxicity according to WHO classification. Results: no patients had grade 4 toxicity after its cures. A grade 2-3 myelotoxicity was observed after 52 treatments (34%) during the second week and after 50 treatments (32.6%) during the fourth week with a satisfactory reversibility. At 10 weeks of treatment, myelotoxicity was reclassified from 0 to 2 for 139 cures (90,8%). Moreover, we found that prior treatment with radiotherapy or chemotherapy did not affect the rates of myelotoxicity. Conclusion: multiple treatments with samarium Sm 153 lexidronam had no significant effect on myelotoxicity. Patients with bone predominant metastatic disease may survive for extended periods of time and may safely be treated with multiple modalities of therapy. (authors)

Preparation and biological behaviour of samarium-153-hydroxyapatite particles for radiation synovectomy

International Nuclear Information System (INIS)

Agrueelles, M.G.; Luppi Berlanga, I.S.; Torres, E.A.; Rutty Sola, G.A.; Rimoldi, G.

1998-01-01

The preparation and labelling procedures of 153 Sm-hydroxyapatite ( 153 Sm-HA) are described in this paper. Hydroxyapatite (HA) was prepared and studied as a radiosynovectomy agent. HA particles were prepared from the reaction of calcium nitrate and ammonia phosphate at high pH Samarium-153 labelling was done in two steps with citric acid. A serie of experimental conditions, such as specific activity, citric acid mass, radioactive solution volume, in-vitro stability, have been carried out. Radiolabelling efficiency was greater than 95%. In vitro studies showed high stability (≥99%). Animal studies showed a good retention in the synovium, with a very low extra-articular leakage over 6 days after administration. (author)

Nucleation and growth kinetics of zirconium hydroxide by precipitation with ammonium hydroxide

International Nuclear Information System (INIS)

Carleson, T.E.; Chipman, N.A.

1987-01-01

The results of a study of the nucleation and growth kinetics of the precipitation of zirconium hydroxide from the reaction of hexafluorozirconate solution with ammonium hydroxide are reported. The McCabe linear growth rate model was used to correlate the results. The growth rate decreased with residence time and supersaturation for studies with 7 residence times (3.5 - 90 minutes and two supersaturation ratios (0.03 - 0.04, and 0.4). The nucleation rate increased with residence time and supersaturation. A negative kinetic order of nucleation was observed that may be due to the inhibition of particle growth by adsorption of reacting species on the crystal surfaces

Evaluation of layered zinc hydroxide nitrate and zinc/nickel double hydroxide salts in the removal of chromate ions from solutions

Energy Technology Data Exchange (ETDEWEB)

Bortolaz de Oliveira, Henrique; Wypych, Fernando, E-mail: wypych@ufpr.br

2016-11-15

Layered zinc hydroxide nitrate (ZnHN) and Zn/Ni layered double hydroxide salts were synthesized and used to remove chromate ions from solutions at pH 8.0. The materials were characterized by many instrumental techniques before and after chromate ion removal. ZnHN decomposed after contact with the chromate solution, whereas the layered structure of Zn/Ni hydroxide nitrate (Zn/NiHN) and Zn/Ni hydroxide acetate (Zn/NiHA) remained their layers intact after the topotactic anionic exchange reaction, only changing the basal distances. ZnHN, Zn/NiHN, and Zn/NiHA removed 210.1, 144.8, and 170.1 mg of CrO{sub 4}{sup 2−}/g of material, respectively. Although the removal values obtained for Zn/NiHN and Zn/NiHA were smaller than the values predicted for the ideal formulas of the solids (194.3 and 192.4 mg of CrO{sub 4}{sup 2−}/g of material, respectively), the measured capacities were higher than the values achieved with many materials reported in the literature. Kinetic experiments showed the removal reaction was fast. To facilitate the solid/liquid separation process after chromium removal, Zn/Ni layered double hydroxide salts with magnetic supports were also synthesized, and their ability to remove chromate was evaluated. - Highlights: • Zinc hydroxide nitrate and Zn/Ni hydroxide nitrate or acetate were synthesized. • The interlayer anions were replaced by chromate anions at pH=8.0. • Only Zn/Ni hydroxide nitrate or acetate have the structure preserved after exchange. • Fast exchange reaction and high capacity of chromate removal were observed. • Magnetic materials were obtained to facilitate the solids removal the from solutions.

Antimicrobial Activity of Calcium Hydroxide in Endodontics: A Review

Science.gov (United States)

Shalavi, S; Yazdizadeh, M

2012-01-01

The purpose of endodontic therapy is to preserve the patient's natural teeth without compromising the patient's local or systemic health. Calcium hydroxide has been included in several materials and antimicrobial formulations that are used in several treatment modalities in endodontics, such as inter-appointment intracanal medicaments. The purpose of this article was to review the antimicrobial properties of calcium hydroxide in endodontics. Calcium hydroxide has a high pH (approximately 12.5-12.8) and is classified chemically as a strong base. The lethal effects of calcium hydroxide on bacterial cells are probably due to protein denaturation and damage to DNA and cytoplasmic membranes. Calcium hydroxide has a wide range of antimicrobial activity against common endodontic pathogens but is less effective against Enterococcus faecalis and Candida albicans. Calcium hydroxide is also a valuable anti-endotoxin agent. However, its effect on microbial biofilms is controversial. PMID:23323217

Fabrication of a PVC membrane samarium(III) sensor based on N,N′,N″-tris(4-pyridyl)trimesic amide as a selectophore

International Nuclear Information System (INIS)

Zamani, Hassan Ali; Naghavi-Reyabbi, Fatemeh; Faridbod, Farnoush; Mohammadhosseini, Majid; Ganjali, Mohammad Reza; Tadjarodi, Azadeh; Rad, Maryam

2013-01-01

A new ion-selective electrode for Sm 3+ ion is described based on the incorporation of N,N′,N″-tris(4-pyridyl)trimesic amide (TPTA) in a poly(vinylchloride) (PVC) matrix. The membrane sensor comprises nitrobenzene (NB) as a plasticizer, and oleic acid (OA) as an anionic additive. The sensor with the optimized composition shows a Nernstian potential response of 19.8 ± 0.5 mV decade −1 over a wide concentration range of 1.0 × 10 −2 and 1 × 10 −6 mol L −1 , with a lower detection limit of 4.7 × 10 −7 mol L −1 and satisfactor applicable pH range of 3.6–9.2. Having a short response time of less than 10 s and a very good selectivity towards the Sm 3+ over a wide variety of interfering cations (e.g. alkali, alkaline earth, transition and heavy metal ions) the sensor seemed to be a promising analytical tool for determination of the Sm 3+ . Hence, it was used as an indicator electrode in the potentiometric titration of samarium ion with EDTA. It was also applied to the direct samarium recovery in binary mixtures. - Highlights: ► A new Sm 3+ -PVC membrane sensor is introduced for determination of Sm 3+ ions in the solutions. ► N,N′,N″-tris(4-pyridyl)trimesic amide was used as a suitable selectophore for samarium sensor. ► Detection limit of the sensor is 4.7 × 10 −7 mol L −1 with a short response time of less than 10 s.

Layered zinc hydroxide salts: Delamination, preferred orientation of hydroxide lamellae, and formation of ZnO nanodiscs

Czech Academy of Sciences Publication Activity Database

Demel, Jan; Pleštil, Josef; Bezdička, Petr; Janda, Pavel; Klementová, Mariana; Lang, Kamil

2011-01-01

Roč. 360, č. 2 (2011), s. 532-539 ISSN 0021-9797 R&D Projects: GA MŠk ME09058; GA ČR GAP207/10/1447 Institutional research plan: CEZ:AV0Z40320502; CEZ:AV0Z40500505; CEZ:AV0Z40400503 Keywords : layered zinc hydroxide * delamination * exfoliation * hydroxide layer * ZnO Subject RIV: CA - Inorganic Chemistry Impact factor: 3.070, year: 2011

Optical and physical properties of samarium doped lithium diborate glasses

Science.gov (United States)

Hanumantharaju, N.; Sardarpasha, K. R.; Gowda, V. C. Veeranna

2018-05-01

Sm3+ doped lithium di-borate glasses with composition 30Li2O-60B2O3-(10-x) PbO, (where 0 molar volume with samarium ion content indicates the openness of the glass structure. The gradual increase in average separation of boron-boron atoms with VmB clearly indicates deterioration of borate glass network, which in turn leads to decrease in the oxygen packing density. The replacements of Sm2O3 for PbO depolymerise the chain structure and that would increase the concentration of non-bridging oxygens. The marginal increase of optical band gap energy after 1.0 mol.% of Sm2O3 is explained by considering the structural modification in lead-borate. The influence of Sm3+ ion on physical and optical properties in lithium-lead-borate glasses is investigated and the results were discussed in view of the structure of borate glass network.

Polysulfide intercalated layered double hydroxides for metal capture applications

Energy Technology Data Exchange (ETDEWEB)

Kanatzidis, Mercouri G.; Ma, Shulan

2017-04-04

Polysulfide intercalated layered double hydroxides and methods for their use in vapor and liquid-phase metal capture applications are provided. The layered double hydroxides comprise a plurality of positively charged host layers of mixed metal hydroxides separated by interlayer spaces. Polysulfide anions are intercalated in the interlayer spaces.

Preparation and examination of properties of samarium-153-EDTMP complex; Otrzymywanie chelatu kwasu etylenodiaminotetrametylenofosfonowego (EDTMP) z samarem-153 i badanie jego wlasciwosci

Energy Technology Data Exchange (ETDEWEB)

Nowak, M. [Institute of Atomic Energy, Otwock-Swierk (Poland); Garnuszek, P.; Lukasiewicz, A.; Wozniak, I.; Zulczyk, W. [Osrodek Badawczo-Rozwojowy Izotopow, Otwock-Swierk (Poland); Licinska, I. [Instytut Lekow, Warsaw (Poland)

1995-12-31

Preparation and properties of ethylenediaminetetramethylenephosphonic acid (EDTMP) as well as some properties of {sup 153}Sm-EDTMP chelate have been examined. The chelate formed by samarium-153 (46.3 h, {beta}{sup -}-decay) with EDTMP exhibits high bone uptake and can be used for treatment of disseminated, painful skeletal metastases. The purity and stability of solutions of {sup 153}Sm-EDTMP chelate were examined in a broad range of samarium concentration and {sup 153}Sm specific activity. The complex under study was examined by radio-TLC, -electrophoresis and radio-HPLC. The results obtained suggest the small size of molecules of {sup 153}Sm-EDTMP chelate as compared with molecules of ``free``EDTMP. The results of biodistribution of {sup 153}Sm-EDTMP determined in rats indicate the quick blood clearance, high deposition of radioactivity in bone and quick excretion of radioactivity into urine. No specific uptake of {sup 153}Sm-EDTMP in extra-skeletal organs was found. (author). 42 refs, 13 figs, 22 tabs.

Calcium hydroxide suppresses Porphyromonas endodontalis lipopolysaccharide-induced bone destruction.

Science.gov (United States)

Guo, J; Yang, D; Okamura, H; Teramachi, J; Ochiai, K; Qiu, L; Haneji, T

2014-05-01

Porphyromonas endodontalis and its main virulence factor, lipopolysaccharide (LPS), are associated with the development of periapical diseases and alveolar bone loss. Calcium hydroxide is commonly used for endodontic therapy. However, the effects of calcium hydroxide on the virulence of P. endodontalis LPS and the mechanism of P. endodontalis LPS-induced bone destruction are not clear. Calcium hydroxide rescued the P. endodontalis LPS-suppressed viability of MC3T3-E1 cells and activity of nuclear factor-κB (NF-κB) in these cells, resulting in the reduced expression of interleukin-6 and tumor necrosis factor-α. In addition, calcium hydroxide inhibited P. endodontalis LPS-induced osteoclastogenesis by decreasing the activities of NF-κB, p38, and ERK1/2 and the expression of nuclear factor of activated T-cell cytoplasmic 1 in RAW264.7 cells. Calcium hydroxide also rescued the P. endodontalis LPS-induced osteoclastogenesis and bone destruction in mouse calvaria. Taken together, our present results indicate that calcium hydroxide suppressed bone destruction by attenuating the virulence of P. endodontalis LPS on bone cells.

Intercalation studies of zinc hydroxide chloride: Ammonia and amino acids

International Nuclear Information System (INIS)

Arízaga, Gregorio Guadalupe Carbajal

2012-01-01

Zinc hydroxide chloride (ZHC) is a layered hydroxide salt with formula Zn 5 (OH) 8 Cl 2 ·2H 2 O. It was tested as intercalation matrix for the first time and results were compared with intercalation products of the well-known zinc hydroxide nitrate and a Zn/Al layered double hydroxide. Ammonia was intercalated into ZHC, while no significant intercalation occurred in ZHN. Aspartic acid intercalation was only achieved by co-precipitation at pH=10 with ZHC and pH=8 with zinc hydroxide nitrate. Higher pH resistance in ZHC favored total deprotonation of both carboxylic groups of the Asp molecule. ZHC conferred more thermal protection against Asp combustion presenting exothermic peaks even at 452 °C while the exothermic event in ZHN was 366 °C and in the LDH at 276 °C. - Graphical abstract: The zinc hydroxide chloride (ZHC) with formula Zn 5 (OH) 8 Cl 2 ·2H 2 O was tested as intercalation matrix. In comparison with the well-known zinc hydroxide nitrate (ZHN) and layered double hydroxides (LDH), ZHC was the best matrix for thermal protection of Asp combustion, presenting exothermic peaks even at 452 °C, while the highest exothermic event in ZHN was at 366 °C, and in the LDH it was at 276 °C. Highlights: ► Zinc hydroxide chloride (ZHC) was tested as intercalation matrix for the first time. ► ZHC has higher chemical and thermal stability than zinc hydroxide nitrate and LDH. ► NH 3 molecules can be intercalated into ZHC. ► The amino group of amino acids limits the intercalation by ion-exchange.

Potentiometric study of samarium oxides formation from its chloride in a molten eutectic mixture of sodium and cesium chlorides

International Nuclear Information System (INIS)

Smolenskij, V.V.; Bove, A.L.; Del'mukhamedov, R.D.; Borodina, N.P.; Gavrilov, A.G.

1997-01-01

Interaction of trivalent samarium cations with oxide-ions in NaCl-2CsCl melt at 973 K has been studied by potentiometric method using electrochemical cell with two platinum-oxygen electrodes with a solid electrolyte membrane. The mechanism of the interaction and composition of the reaction products, depending on the medium oxyacidity, have been considered. Certain thermodynamic characteristics of the process have been calculated

Structural phase transition and electronic properties in samarium chalcogenides

Energy Technology Data Exchange (ETDEWEB)

Panwar, Y. S., E-mail: yspanwar2011@gmail.com [Department of Physics, Govt. New Science College Dewas-455001 (India); Aynyas, Mahendra [Department of Physics, C.S.A. Govt. P.G. College, Sehore, 466001 (India); Pataiya, J.; Sanyal, Sankar P. [Department of Physics, Barkatullah University, Bhopal, 462026 (India)

2016-05-06

The electronic structure and high pressure properties of samarium monochalcogenides SmS, SmSe and SmTe have been reported by using tight binding linear muffin-tin-orbital (TB-LMTO) method within the local density approximation (LDA). The total energy as a function of volume is evaluated. It is found that these monochalcogenides are stable in NaCl-type structure under ambient pressure. We predict a structural phase transition from NaCl-type (B{sub 1}-phase) structure to CsCl-type (B{sub 2}-type) structure for these compounds. Phase transition pressures were found to be 1.7, 4.4 and 6.6 GPa, for SmS, SmSe and SmTe respectively. Apart from this, the lattice parameter (a{sub 0}), bulk modulus (B{sub 0}), band structure (BS) and density of states (DOS) are calculated. From energy band diagram we observed that these compounds exhibit metallic character. The calculated values of equilibrium lattice parameter and phase transition pressure are in general good agreement with available data.

Sorption of samarium in iron (II) and (III) phosphates in aqueous systems; Sorcion de samario en fosfatos de hierro (II) y (III) en sistemas acuosos

Energy Technology Data Exchange (ETDEWEB)

Diaz F, J C

2006-07-01

The radioactive residues that are stored in the radioactive confinements its need to stay isolated of the environment while the radioactivity levels be noxious. An important mechanism by which the radioactive residues can to reach the environment, it is the migration of these through the underground water. That it makes necessary the investigation of reactive materials that interacting with those radionuclides and that its are able to remove them from the watery resources. The synthesis and characterization of materials that can be useful in Environmental Chemistry are very important because its characteristics are exposed and its behavior in chemical phenomena as the sorption watery medium is necessary to use it in the environmental protection. In this work it was carried out the sorption study of the samarium III ion in the iron (II) and (III) phosphate; obtaining the sorption isotherms in function of pH, of the phosphate mass and of the concentration of the samarium ion using UV-visible spectroscopy to determine the removal percentage. The developed experiments show that as much the ferrous phosphate as the ferric phosphate present a great affinity by the samarium III, for what it use like reactive material in contention walls can be very viable because it sorption capacity has overcome 90% to pH values similar to those of the underground and also mentioning that the form to obtain these materials is very economic and simple. (Author)

Preparation of plate-shape nano-magnesium hydroxide from asbestos tailings

International Nuclear Information System (INIS)

Du Gaoxiang; Zheng Shuilin

2009-01-01

To prepare magnesium hydroxide is one of the effective methods to the comprehensive utilization of asbestos tailings. Nano-scale magnesium hydroxide was prepared and mechanisms of in-situ surface modification were characterized in the paper. Process conditions of preparation of magnesium hydroxide from purified hydrochloric acid leachate of asbestos tailings were optimized and in-situ surface modification of the product was carried out. Results showed that optimum process conditions for preparing nano-scale magnesium hydroxide were as follows: initial concentration of Mg 2+ in the leachate was 22.75g/L, precipitant was NaOH solution (mass concentration 20%), reaction temperature was 50 deg. C, and reaction time was 5min. The diameter and thickness of the plate nano-scale magnesium hydroxide powder prepared under optimal conditions were about 100 nm and 10 nm, respectively. However, particle agglomeration was obvious, the particle size increased to micron-grade. Dispersity of the magnesium hydroxide powder could be elevated by in-situ modification by silane FR-693, titanate YB-502 and polyethylene glycol and optimum dosages were 1.5%, 1.5% and 0.75% of the mass of magnesium hydroxide, respectively. All of the modifiers adsorbed chemically on surfaces of magnesium hydroxide particles, among which Si-O-Mg bonds formed among silane FR-693 and the particle surfaces and Ti-O-Mg among titanate YB-502 and the surfaces.

Separation of lanthanum from samarium on solid aluminum electrode in LiCl-KCl eutectic melts

International Nuclear Information System (INIS)

De-Bin Ji; Mi-Lin Zhang; Xing Li; Xiao-Yan Jing; Wei Han; Yong-De Yan; Yun Xue; Zhi-Jian Zhang; Harbin Engineering University, Harbin

2015-01-01

This paper presents an electrochemical study on the separation of lanthanum from samarium on aluminum electrode at 773 K. The results from different electrochemical methods showed that Sm(III) and La(III) formed Al-Sm and Al-La intermetallic compounds on an aluminum electrode at electrode potential around -1.67 and -1.46 V, respectively. The electrochemical separation of lanthanum was carried out in LiCl-KCl-LaCl 3 -SmCl 3 melts on solid aluminum electrodes at 773 K by potentiostatic electrolysis at -1.45 V for 40 h and the separation efficiency was 99.1 %. (author)

Nickel and cobalt bimetallic hydroxide catalysts for urea electro-oxidation

International Nuclear Information System (INIS)

Yan Wei; Wang Dan; Botte, Gerardine G.

2012-01-01

Nickel–Cobalt bimetallic hydroxide electrocatalysts, synthesized through a one-step electrodeposition method, were evaluated for the oxidation of urea in alkaline conditions with the intention of reducing the oxidation overpotential for this reaction. The Nickel–Cobalt bimetallic hydroxide catalysts were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDXS), Raman spectroscopy, cyclic voltammetry (CV), and polarization techniques. A significant reduction in the overpotential (150 mV) of the reaction was observed with the Nickel–Cobalt bimetallic hydroxide electrode (ca. 43% Co content) when compared to a nickel hydroxide electrode. The decrease of the urea oxidation potential on the Nickel–Cobalt bimetallic hydroxide electrodes reveals great potential for future applications of urea electro-oxidation, including wastewater remediation, hydrogen production, sensors, and fuel cells.

Evaluation of layered zinc hydroxide nitrate and zinc/nickel double hydroxide salts in the removal of chromate ions from solutions

Science.gov (United States)

de Oliveira, Henrique Bortolaz; Wypych, Fernando

2016-11-01

Layered zinc hydroxide nitrate (ZnHN) and Zn/Ni layered double hydroxide salts were synthesized and used to remove chromate ions from solutions at pH 8.0. The materials were characterized by many instrumental techniques before and after chromate ion removal. ZnHN decomposed after contact with the chromate solution, whereas the layered structure of Zn/Ni hydroxide nitrate (Zn/NiHN) and Zn/Ni hydroxide acetate (Zn/NiHA) remained their layers intact after the topotactic anionic exchange reaction, only changing the basal distances. ZnHN, Zn/NiHN, and Zn/NiHA removed 210.1, 144.8, and 170.1 mg of CrO42-/g of material, respectively. Although the removal values obtained for Zn/NiHN and Zn/NiHA were smaller than the values predicted for the ideal formulas of the solids (194.3 and 192.4 mg of CrO42-/g of material, respectively), the measured capacities were higher than the values achieved with many materials reported in the literature. Kinetic experiments showed the removal reaction was fast. To facilitate the solid/liquid separation process after chromium removal, Zn/Ni layered double hydroxide salts with magnetic supports were also synthesized, and their ability to remove chromate was evaluated.

Iodine Sequestration Using Delafossites and Layered Hydroxides

International Nuclear Information System (INIS)

J.D. Pless; J.B. Chwirka; J.L. Krumhansl

2006-01-01

The objective of this document is to report on early success for sequestering 129 I. Sorption coefficients (K d ) for I - and IO 3 - onto delafossites, spinels and layered metal hydroxides were measured in order to compare their applicability for sequestering 129 I. The studies were performed using a dilute fluid composition representative of groundwater indigenous to the Yucca mountain area. Delafossites generally exhibited relatively poor sorption coefficients ( 1.7 mL/g). In contrast, the composition of the layered hydroxides significantly affects their ability to sorb I. Cu/Al and Cu/Cr layered hydroxide samples exhibit K d 's greater than 10 3 mL/g for both I - and IO 3 -

Structural and luminescence properties of samarium doped lead alumino borate glasses

Science.gov (United States)

Mohan, Shaweta; Kaur, Simranpreet; Singh, D. P.; Kaur, Puneet

2017-11-01

The study reports the effect of samarium concentration on the physical, structural and spectroscopic characteristics of samarium doped lead alumino borate glasses having composition 20PbO-(10-x)Al2O3-70B2O3-xSm2O3; x = 0.1, 0.5, 1.0 and 2.0 mol %. The glasses were fabricated by conventional melt-quenching technique and then characterized by XRD, FTIR, optical absorption and fluorescence spectra. X-ray diffraction studies confirmed the amorphous nature of the prepared glasses. FTIR spectra indicate the presence of BO3, BO4, AlO6 and a few other structural groups. Various physical properties such as density, molar volume, refractive index, rare earth ion concentration, boron-boron distance and polarizability etc. were determined using conventional methods and standard formulae. The Judd-Ofelt theory was applied on the optical absorption spectra of the glasses to evaluate the three phenomenological intensity parameters Ω2, Ω4 and Ω6. The value of Ω2 was found to be highest for glass with 1 mol% Sm2O3 and attributed to the asymmetry of the ligand field at the rare earth ion site and the rare earth oxygen (Sm-O) covalency. The calculated intensity parameters and fluorescence spectra were further used to predict the radiative transition probability (A), radiative lifetime (τR), branching ratio (βR), peak wavelength (λp), effective line widths (Δλeff) and stimulated emission cross-section (σ) for the characteristic 4G5/2 → 6H5/2, 6H7/2 and 6H9/2 transitions of the Sm3+ ion. Concentration quenching was observed for 2 mol% concentration of Sm2O3 and ascribed to energy transfer through various cross-relaxation channels between Sm3+ ions. Reasonably high values of branching ratios and stimulated emission cross-section for the prepared glasses points towards their utility in the development of visible lasers emitting in the reddish-orange spectral region. However, the glass with 1 mol% Sm2O3 was found to show better radiative properties.

Nickel-cobalt hydroxide nanosheets: Synthesis, morphology and electrochemical properties

Czech Academy of Sciences Publication Activity Database

Schneiderová, Barbora; Demel, Jan; Zhigunov, Alexander; Bohuslav, Jan; Tarábková, Hana; Janda, Pavel; Lang, Kamil

2017-01-01

Roč. 499, AUG (2017), s. 138-144 ISSN 0021-9797 Institutional support: RVO:61388980 ; RVO:61389013 ; RVO:61388955 Keywords : Hydroxide nanosheets * Delamination * Exfoliation * Layered nickel hydroxide * Layered cobalt hydroxide * Electrode material Subject RIV: CA - Inorganic Chemistry; CF - Physical ; Theoretical Chemistry (UFCH-W); CD - Macromolecular Chemistry (UMCH-V) OBOR OECD: Inorganic and nuclear chemistry; Physical chemistry (UFCH-W); Polymer science (UMCH-V) Impact factor: 4.233, year: 2016

Aluminum hydroxide issue closure package

International Nuclear Information System (INIS)

Bergman, T.B.

1998-01-01

Aluminum hydroxide coatings on fuel elements stored in aluminum canisters in K West Basin were measured in July and August 1998. Good quality data was produced that enabled statistical analysis to determine a bounding value for aluminum hydroxide at a 99% confidence level. The updated bounding value is 10.6 kg per Multi-Canister Overpack (MCO), compared to the previously estimated bounding value of 8 kg/MCO. Thermal analysis using the updated bounding value, shows that the MCO generates oxygen concentrate that are below the lower flammability limits during the 40-year interim storage period and are, therefore, acceptable

Europium and samarium doped calcium sulfide thin films grown by PLD

International Nuclear Information System (INIS)

Christoulakis, S.; Suchea, M; Katsarakis, N.; Koudoumas, E

2007-01-01

Europium and samarium doped calcium sulfide thin films (CaS:Eu,Sm) with different thickness were prepared by the pulsed laser deposition technique using sintered targets. A typical homemade deposition chamber and XeCl excimer laser (308 nm) were employed and the films were deposited in helium atmosphere onto silicon and corning glass substrates. Structural investigations carried out by X-ray diffraction and atomic force microscopy showed a strong influence of the deposition parameters on the film properties. The films grown had an amorphous or polycrystalline structure depending on growth temperature and the number of pulses used, the same parameters affecting the film roughness, the grain shape and dimensions, the film thickness and the optical transmittance. This work indicates that pulsed laser deposition can be a suitable technique for the preparation of CaS:Eu,Sm thin films, the film characteristics being controlled by the growth conditions

Aluminium hydroxide-induced granulomas in pigs

DEFF Research Database (Denmark)

Valtulini, S; Macchi, C; Ballanti, P

2005-01-01

The effect of intramuscular injection of 40 mg/2 ml aluminium hydroxide in the neck of pigs was examined in a number of ways. The investigation followed repeated slaughterhouse reports, according to which 64.8% of pigs from one particular farm were found at slaughter to have one or more nodules...... in the muscles of the neck (group slaughtered). The pigs had been injected with a vaccine containing 40 mg/2 ml dose of aluminium hydroxide as adjuvant. Research consisted of two phases: first, an epidemiological study was carried out, aimed at determining the risk factors for the granulomas. The results...... and adjuvant) to pigs inoculated twice with apyrogenic bi-distilled water (group water) and to pigs inoculated once with the adjuvant and once with apyrogenic bi-distilled water (group adjuvant/water). Both studies agreed in their conclusions, which indicate that the high amount of aluminium hydroxide...

Behavior of hydroxide at the water/vapor interface

Science.gov (United States)

Winter, Bernd; Faubel, Manfred; Vácha, Robert; Jungwirth, Pavel

2009-06-01

Hydroxide and hydronium, which represent the ionic products of water autolysis, exhibit a peculiar surface behavior. While consensus has been established that the concentration of hydronium cations is enhanced at the surface with respect to the bulk, the affinity of hydroxide anions for the water/vapor interface has been a subject of an ongoing controversy. On the one hand, electrophoretic and titration measurements of air bubbles or oil droplets in water have been interpreted in terms of a dramatic interfacial accumulation of OH -. On the other hand, surface-selective non-linear spectroscopies, surface tension measurements, and molecular simulations show no or at most a weak surface affinity of hydroxide ions. Here, we summarize the current situation and provide new evidence for the lack of appreciable surface enhancement of OH -, based on photoelectron spectroscopy from a liquid jet and on molecular dynamics simulations with polarizable potentials at varying hydroxide concentrations.

Antimony removal from aqueous solutions using Zirconium hydroxide

International Nuclear Information System (INIS)

Petrescu, D.; Velciu, L.; Bucur, C.

2016-01-01

In this paper it is presented an experimental test for non-radioactive antimony removal from aqueous solutions using zirconium hydroxide powder. Also, it was studied how the temperature and pH influences antimony adsorption onto zirconium hydroxide surface. After the adsorption, solutions were filtered on Cellulose Mixed Ester Membrane with 0.2 μm pore size to remove the zirconium powder and then the aqueous solutions were sent to Inductively Coupled Plasma Optic Emission Spectrometry (ICP-OES) for quantitative analysis of Sb. Zirconium hydroxide powders were examined by optical microscopy. For the solutions that were tested at pH 4.5 and 10.2 the antimony concentration dropped below the detection limit of ICP-OES device, proof of antimony adsorption on zirconium hydroxide. Also, for the other tested solutions which had pH=12 the antimony concentration reduced with 77% and 80%. The temperature had no influence upon adsorption mechanism. (authors)

Layered double hydroxides

DEFF Research Database (Denmark)

López Rayo, Sandra; Imran, Ahmad; Hansen, Hans Chr. Bruun

2017-01-01

A novel zinc (Zn) fertilizer concept based on Zn doped layered double hydroxides (Zn-doped Mg-Fe-LDHs) has been investigated. Zn-doped Mg-Fe-LDHs were synthetized, their chemical composition was analyzed and their nutrient release was studied in buffered solutions with different pH values. Uptake...

Single sheet metal oxides and hydroxides

DEFF Research Database (Denmark)

Huang, Lizhi

The synthesis of layered double hydroxides (LDHs) provides a relatively easy and traditional way to build versatile chemical compounds with a rough control of the bulk structure. The delamination of LDHs to form their single host layers (2D nanosheets) and the capability to reassemble them offer......) Delamination of the LDHs structure (oxGRC12) with the formation of single sheet iron (hydr)oxide (SSI). (3) Assembly of the new 2D nanosheets layer by layer to achieve desired functionalities....

Synthesis of polymer nanocomposites using layered hydroxide salts (LHS)

International Nuclear Information System (INIS)

Machado, Paula F. de M.P.B.; Lona, Liliane M.F.; Marangoni, Rafael; Wypych, Fernando

2011-01-01

In this work latexes of poly (methyl methacrylate) were synthesized via emulsion polymerization using layered hydroxide salts (LHS) as reinforcements: zinc hydroxide nitrate (Zn 5 (OH) 8 (NO 3 ) 2 ·2H 2 O) and copper hydroxide acetate (Cu 2 (OH) 3 CH 3 COO.H 2 O). The LHSs were characterized by X-ray powder diffraction (XRPD). Mastersizer analysis indicated the particle diameter of the latexes. Molecular weights and conversion data were also obtained. (author)

Discharge Characteristics of the Nickel Hydroxide Electrode in 30% KOH

International Nuclear Information System (INIS)

Kim, Young Jin

1989-01-01

The discharge behavior of the nickel hydroxide electrode has been investigated in 30% KOH at 25 .deg. C. Two voltage plateaus are displayed on the discharge curve of C/20. It is shown that the impedance of the nickel hydroxide electrode increases with decrease of the discharge potential. The discharge behavior of the nickel hydroxide electrode has been investigated in 30% KOH indicating the reduction of the β-NiOOH to the β-Ni(OH) 2 by proton diffusion process and hence the electronic conductivity change of the nickel hydroxide electrode. Furthermore, the γ-NiOOH, produced by prolonged oxidation of the β-NiOOH in 30% KOH, discharges at a slightly lower potential than the β-Ni(OH) 2 that could result in the life-limiting factor of several alkaline electrolyte storage batteries using the nickel hydroxide electrode as the positive plate

Adsorption of procion red using layer double hydroxide Mg/Al

Directory of Open Access Journals (Sweden)

Muhammad Imron

2017-07-01

Full Text Available Layer double hydroxide Mg/Al was synthesized by inorganic synthetic method. Material was characterized using FTIR and XRD analyses and used as adsorbent of procion red dye in aqueous medium.  Factors that affect the adsorption process are adsorption time as the kinetic parameter; and the temperature and concentration of procion red as the thermodynamic parameter. FTIR spectra of layer double hydroxides showed unique vibration at wavenumber 1300 cm-1 and 1600 cm-1. Characterization using XRD shows diffraction angles at 29o, 27o, and 28o, which are typical of Mg/Al double layer hydroxides. Adsorption of procion red using layer double hydroxide Mg/Al resulted adsorption rate 7.1 minutes-1, maximum adsorption capacity 111.1 mg/g at 60 oC with increasing energy by increasing adsorption temperature.   Keywords: Layered double hydroxides, adsorption, procion red.

Intercalation studies of zinc hydroxide chloride: Ammonia and amino acids

Science.gov (United States)

Arízaga, Gregorio Guadalupe Carbajal

2012-01-01

Zinc hydroxide chloride (ZHC) is a layered hydroxide salt with formula Zn5(OH)8Cl2·2H2O. It was tested as intercalation matrix for the first time and results were compared with intercalation products of the well-known zinc hydroxide nitrate and a Zn/Al layered double hydroxide. Ammonia was intercalated into ZHC, while no significant intercalation occurred in ZHN. Aspartic acid intercalation was only achieved by co-precipitation at pH=10 with ZHC and pH=8 with zinc hydroxide nitrate. Higher pH resistance in ZHC favored total deprotonation of both carboxylic groups of the Asp molecule. ZHC conferred more thermal protection against Asp combustion presenting exothermic peaks even at 452 °C while the exothermic event in ZHN was 366 °C and in the LDH at 276 °C.

The dynamics of the laser-induced metal-semiconductor phase transition of samarium sulfide (SmS)

International Nuclear Information System (INIS)

Kaempfer, Tino

2009-01-01

The present thesis is dedicated to the experimental study of the metal-semiconductor phase transition of samarium sulfide (SmS): Temperature- and time-resolved experiments on the characterization of the phase transition of mixed-valence SmS samples (M-SmS) are presented. The measurement of the dynamics of the laser-induced phase transition pursues via time-resolved ultrashort-time microscopy and by X-ray diffraction with sub-picosecond time resolution. The electronic and structural processes, which follow an excitation of M-SmS with infrared femtosecond laser pulses, are physically interpreted on the base of the results obtained in this thesis and model imaginations. [de

On reactions of polymerization of p-element hydroxides in aqueous solutions

International Nuclear Information System (INIS)

Tikavyj, V.F.; Lesnikovich, A.I.

1978-01-01

The tendency of p-element hydroxides towards polymerization in aqueous solutions has been considered with respect to their location in the Periodic Table. Stable hydroxides of d-elements are practically all polymerized; among s-elements only berillium and magnesium hydroxides polymerize as the least dissociated ones. Hydroxides of the elements located to the right of the 4 Group and above the 5-th Period do not polymerize in aqueous solutions. The structure and tendency towards polymerization of In, Te, and I compounds have been studied. The tendency to polymerization of all hydroxides of p-elements located below the 4-th Period is explained from the standpoint of electron structure and the simplest thermodynamic analysis (entropy, enthalpy)

Samarium (III Selective Membrane Sensor Based on Tin (IV Boratophosphate

Directory of Open Access Journals (Sweden)

Ashok S. K. Kumar

2004-08-01

Full Text Available Abstract: A number of Sm (III selective membranes of varying compositions using tin (IV boratophosphate as electroactive material were prepared. Polyvinyl chloride, polystyrene and epoxy resin were used as binding materials. Membrane having composition of 40% exchanger and 60% epoxy resin exhibited best performance. This membrane worked well over a wide concentration range of 1x10-5M to 1x10-1 M of samarium ions with a Super-Nernstian slope of 40 mV/decade. It has a fast response time of less than 10 seconds and can be used for at least six months without any considerable divergence in potentials. The proposed sensor revealed good selectivities with respect to alkali, alkaline earth, some transition and rare earth metal ions and can be used in the pH range of 4.0-10.0. It was used as an indicator electrode in the potentiometric titration of Sm (III ions against EDTA. Effect of internal solution was studied and the electrode was successfully used in non-aqueous media, too.

Rapid collection of iron hydroxide for determination of Th isotopes in seawater

Energy Technology Data Exchange (ETDEWEB)

Okubo, Ayako, E-mail: okubo.ayako@jaea.go.jp [Japan Atomic Energy Agency, Research Group for Analytical Chemistry (Japan); Obata, Hajime, E-mail: obata@aori.u-tokyo.ac.jp [Atmosphere Ocean Research Institute, The University of Tokyo (Japan); Magara, Masaaki, E-mail: magara.masaaki@jaea.go.jp [Japan Atomic Energy Agency, Research Group for Analytical Chemistry (Japan); Kimura, Takaumi, E-mail: kimura.takaumi@jaea.go.jp [Japan Atomic Energy Agency, Research Group for Analytical Chemistry (Japan); Ogawa, Hiroshi, E-mail: hogawa@aori.u-tokyo.ac.jp [Atmosphere Ocean Research Institute, The University of Tokyo (Japan)

2013-12-04

Graphical abstract: -- Highlights: •DIAION CR-20 chelating resin has successfully collected iron-hydroxide with Th isotopes. •Ferric ions in the iron hydroxide were bonded to functional groups of the chelating resin. •The time of preconcentration step was markedly reduced from a few days to 3–4 h. -- Abstract: This work introduces a novel method of recovery of iron hydroxide using a DIAION CR-20 chelating resin column to determine Th isotopes in seawater with a sector field (SF) inductively coupled plasma mass spectrometer (ICP-MS). Thorium isotopes in seawater were co-precipitated with iron hydroxide, and this precipitate was sent to chelating resin column. Ferric ions in the iron hydroxide were bonded to functional groups of the chelating resin directly, resulting in a pH increase of the effluent by release of hydroxide ion from the iron hydroxide. The co-precipitated thorium isotopes were quantitatively collected within the column, which indicated that thorium was retained on the iron hydroxide remaining on the chelating column. The chelating column quantitatively collected {sup 232}Th with iron hydroxide in seawater at flow rates of 20–25 mL min{sup −1}. Based on this flow rate, a 5 L sample was processed within 3–4 h. The >20 h aging of iron hydroxide tends to reduce the recovery of {sup 232}Th. The rapid collection method was successfully applied to the determination of {sup 230}Th and {sup 232}Th in open-ocean seawater samples.

Acid mine water neutralisation with ammonium hydroxide and ...

African Journals Online (AJOL)

This study showed that NH4OH can be used for treatment of acid mine drainage rich in sulphates and NH4OH can be recycled in the process. Hydrated lime treatment resulted in removal of the remaining ammonia using a rotary evaporator. Keywords: acid mine water, ammonium hydroxide, barium hydroxide, sulphate ...

Determination of trace amounts of rare earth elements in samarium, terbium and disprosium oxides by graphite furnace atomic-absorption spectrometry

International Nuclear Information System (INIS)

Dantas, E.S.K.

1990-01-01

A graphite furnace atomic-absorption spectrometry method for the determination of neodymium, europium, terbium, dysprosium and yttrium at trace level in samarium oxide; of samarium, europium, dysprosium, holmium, erbium and yttrium in terbium oxide and of europium, terbium, holmium, erbium and yttrium in dysprosium oxide was established. The best pyrolysis and atomization temperatures were determined for each lanthanide considered. Calibration curves were obtained for the pure elements, for binary mixtures formed by the matrix and each of the lanthanides studied and, finally, for the complex mixtures constituted by the matrix and all the other lanthanide of the group under scrutiny. This study has been carried out to examine the interference of the presence of one lanthanide on the behaviour of the other, since a lack of linearity on the calibration curves has been observed in some cases. Detection and determination limits have been determined as well. The detection limits encountered were within the range 0.002 to 0.3% for different elements. The precision of the method expressed as the relative standard deviation was calculated for each element present in each of the matrices studied. The conclusion arrived at is that the method can be applied for determining the above mentioned lanthanides present in the matrices studied with purity up to 99.50%. (author)

Dehydration-rehydration behaviour of zirconium hydroxide and aluminium hydroxide coprecipitated hydrogel

International Nuclear Information System (INIS)

Mitra, N.K.; Guha, P.; Basumajumdar, A.

1989-01-01

Equilibrium dehydration loss experiments on zirconium and aluminium hydroxide coprecipitated hyrogels were carried out up to 600deg and the above heat treated samples were subjected to rehydration at various humidities in order to study the structural flexibilties of the above hydrogel with respect to orientation of water molecules. (author). 6 refs., 3 tabs

Oriented growth of thin films of samarium oxide by MOCVD

Indian Academy of Sciences (India)

Unknown

Very thin layers of rare earth oxides, such as Sm2O3 and epitaxial Gd2O3, grown by thermal ... As the inorganic salts of the lanthanides, such as their halides, are ... sodium hydroxide, followed by the addition of ethanolic. 1,10-phenanthroline ...

Calcium hydroxide silylation reaction with trimethylchlorosilane

Directory of Open Access Journals (Sweden)

Novoselnov Anatoliy A.

2016-01-01

Full Text Available The silylation reaction of a calcium hydroxide with a trimethylchlorosilane is studied as a silylation model by the gas-liquid chromatography. The silylation process is divided into three stages. A material balance of these stages is calculated. The schemes of the reactions at each stage of the process are proposed. The modified calcium hydroxide obtained at three repetitive stages of the silylation reaction has been investigated by the x-ray phase analysis, IR spectroscopy, thermal analysis, electron microscopy in a combination with the elemental analysis. It has been determined that at the first stage of the interaction the processes of the trimethylchlorosilane hydrolysis and of the hydrolysis products condensation dominate, and at the same time an adsorption process of the trimethylchlorosilane and its derivatives starts. Further, the hydrolysis of the trimethylchlorosilane by the «new» portions of a water formed in the reaction of a calcium hydroxide with a hydrogen chloride takes place, simultaneously the secondary reactions of the Si-O-Ca – ties’ formation and cleavage occur including as a silylation-desilylation dynamic equilibrium process.

Synthesis of samarium complexes with the derivative binder of Schiff Quinolinic base. Characterization and photophysical study; Sintesis de complejos de samario con el ligante derivado de base de Schiff Quinolinica. Caracterizacion y estudio fotofisico

Energy Technology Data Exchange (ETDEWEB)

Lucas H, J.

2016-07-01

In this work we determined the metal: binder stoichiometry of the species formed during the UV/Vis spectrophotometric titration of the derivative binder of Schiff quinolinic base, L1 with the samarium nitrate pentahydrate in methanol. Statistical analysis of the data allowed proposing the metal: binder stoichiometry for the synthesis of the complexes which was one mole of samarium salt by 2.5 moles of binder and thus favor the formation of complexes with 1M: 1L and 1M: 2L stoichiometries. They were synthesized in aqueous-organic medium (water-ethanol), isolated and purified two complexes with stoichiometry 1 Sm: 1 L1, complex 1 and 1 Sm: 2 L1, complex 2. The overall yield of the reaction was 76%. The characterization of the formed complexes was performed by visible ultraviolet spectrometry (UV/Vis), nuclear magnetic resonance, X-ray photoelectron spectroscopy (XP S), thermal gravimetric analysis with differential scanning calorimetry (TGA/DSC), and radial distribution function. These complexes were studied by fluorescence and emission phosphorescence at variable temperature. Spectroscopic techniques used in both solution and solid demonstrated the formation and stability of these complexes. In addition XP S indicated that in both complexes the samarium retains its oxidation state 3+. Luminescence studies indicated that there is intra-binding charge transfer which decreases the transfer of light energy from the binder to the samarium. Based on the experimental results, L1 binder molecules and complexes 1 and 2 were modeled that demonstrated the proposed Nc for each complex, as well as allowed to visualize the structural arrangement of the molecules, complexes and binder. (Author)

Fabrication of a PVC membrane samarium(III) sensor based on N,N Prime ,N Double-Prime -tris(4-pyridyl)trimesic amide as a selectophore

Energy Technology Data Exchange (ETDEWEB)

Zamani, Hassan Ali, E-mail: haszamani@yahoo.com [Department of Applied Chemistry, Mashhad Branch, Islamic Azad University, Mashhad (Iran, Islamic Republic of); Naghavi-Reyabbi, Fatemeh [Resident of General Surgery, Endoscopic and Minimaly Invasive Surgery Research Center, Ghaem Hospital, Faculty of Medicine, Mashhad University of Medical Sciences, Mashhad (Iran, Islamic Republic of); Faridbod, Farnoush [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Mohammadhosseini, Majid [Department of Chemistry, Faculty of Basic Sciences, Shahrood Branch, Islamic Azad University, Shahrood (Iran, Islamic Republic of); Ganjali, Mohammad Reza [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Tadjarodi, Azadeh; Rad, Maryam [Department of Chemistry, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of)

2013-03-01

A new ion-selective electrode for Sm{sup 3+} ion is described based on the incorporation of N,N Prime ,N Double-Prime -tris(4-pyridyl)trimesic amide (TPTA) in a poly(vinylchloride) (PVC) matrix. The membrane sensor comprises nitrobenzene (NB) as a plasticizer, and oleic acid (OA) as an anionic additive. The sensor with the optimized composition shows a Nernstian potential response of 19.8 {+-} 0.5 mV decade{sup -1} over a wide concentration range of 1.0 Multiplication-Sign 10{sup -2} and 1 Multiplication-Sign 10{sup -6} mol L{sup -1}, with a lower detection limit of 4.7 Multiplication-Sign 10{sup -7} mol L{sup -1} and satisfactor applicable pH range of 3.6-9.2. Having a short response time of less than 10 s and a very good selectivity towards the Sm{sup 3+} over a wide variety of interfering cations (e.g. alkali, alkaline earth, transition and heavy metal ions) the sensor seemed to be a promising analytical tool for determination of the Sm{sup 3+}. Hence, it was used as an indicator electrode in the potentiometric titration of samarium ion with EDTA. It was also applied to the direct samarium recovery in binary mixtures. - Highlights: Black-Right-Pointing-Pointer A new Sm{sup 3+}-PVC membrane sensor is introduced for determination of Sm{sup 3+} ions in the solutions. Black-Right-Pointing-Pointer N,N Prime ,N Double-Prime -tris(4-pyridyl)trimesic amide was used as a suitable selectophore for samarium sensor. Black-Right-Pointing-Pointer Detection limit of the sensor is 4.7 Multiplication-Sign 10{sup -7} mol L{sup -1} with a short response time of less than 10 s.

Deactivation of nickel hydroxide-gold modified electrodes

OpenAIRE

Caram, Bruno; Tucceri, Ricardo

2013-01-01

The aim of the present work was to study how the charge-transport process of a nickel hydroxide film electrochemically synthesized on a gold substrate is modified when the electrode is stored for a long time. It was found that nickel hydroxide films are deactivated under storage, that is, films became less conductive than films immediately prepared (nondeactivated). This study was carried out in the context of the rotating disc electrode voltammetry when the modified electrode contacts an ele...

Neutralization of Hydroxide Ion in Melt-Grown NaCl Crystals

Science.gov (United States)

Otterson, Dumas A.

1961-01-01

Many recent studies of solid-state phenomena, particularly in the area of crystal imperfections, have involved the use of melt-grown NaCl single crystals. Quite often trace impurities in these materials have had a prominent effect on these phenomena. Trace amounts of hydroxide ion have been found in melt-grown NaCl crystals. This paper describes a nondestructive method of neutralizing the hydroxide ion in such crystals. Crystals of similar hydroxide content are maintained at an elevated temperature below the melting point of NaCl in a flowing atmosphere containing. dry hydrogen chloride. Heat treatment is continued until an analysis of the test specimens shows no excess hydroxide ion. A colorimetric method previously described4 is used for this analysis.

Luminescent materials based on Tb, Eu-containing layered double hydroxides

International Nuclear Information System (INIS)

Zhuravleva, N.G.; Eliseev, A.A.; Lukashin, A.V.; Kinast, U.; Tret'yakov, Yu.D.

2004-01-01

Luminescent materials on the basis of magnesium-aluminium layered double hydroxides with intercalated anionic complexes of terbium and europium picolinates were synthesized. Relying on data of spectroscopy, elementary and X-ray phase analyses, the change in the rare earth complex structure and metal/ligand ratio, depending on the hydroxide layer charge, determined by Mg/Al ratio in the double hydroxide, were ascertained. The values of quantum yields of luminescence for terbium-containing samples amounted to 30-50% [ru

Thermochemical properties of the alkali hydroxides: A review

International Nuclear Information System (INIS)

Konings, R.J.M.; Cordfunke, E.H.P.

1989-01-01

The formation of volatile alkali hydroxides as a result of high-temperature steam corrosion plays an important role in nuclear technology. For the modeling of the volatilization processes, reliable thermodynamic data are required. In the present paper recent physico-chemical experiments by the authors will be discussed and the thermochemical properties of the alkali hydroxide series will be evaluated. (orig.)

Interaction of natural borates with potassium hydroxide solution

International Nuclear Information System (INIS)

Azarova, L.A.; Vinogradov, E.E.; Kudinov, I.B.; Panasyuk, G.P.; Danilov, V.P.

2000-01-01

Interaction of natural borates - inyoite, ulexite and hydroboracite MgCa[B 3 O 4 (OH) 3 ] 2 ·3H 2 O with KOH solution is studied at 50 Deg C by the methods of chemical, x- ray phase, differential thermal analyses and IR spectroscopy. IR spectra points out on island character of forming borates and confirms the data of x-ray phase and chemical analyses about presence of asharite and calcium hydrous borate in resulting products. Hydroboracite (chain structure) under the action of potassium hydroxide passes into borates of magnesium and calcium with island structure and in this case boron transforms partially into liquid phase. When potassium hydroxide interacts with inyoite and ulexite calcium hydroxide and roentgenoamorphous boron-containing product precipitate [ru

Potassium hydroxide: an alternative reagent to perform the modified apt test.

Science.gov (United States)

Chicaiza, Henry; Hellstrand, Karl; Lerer, Trudy; Smith, Sharon; Sylvester, Francisco

2014-09-01

We tested the performance of potassium hydroxide (KOH) in the modified Apt test under different experimental conditions using sodium hydroxide as a positive control. Like sodium hydroxide, KOH differentiated fresh fetal and adult blood stains on a cloth but not dried blood. KOH may be used to perform the Apt test at the bedside. Copyright © 2014 Elsevier Inc. All rights reserved.

Average formation number n-barOH of colloid-type indium hydroxide

International Nuclear Information System (INIS)

Stefanowicz, T.; Szent-Kirallyine Gajda, J.

1983-01-01

Indium perchlorate in perchloric acid solution was titrated with sodium hydroxide solution to various pH values. Indium hydroxide colloid was removed by ultracentrifugation and supernatant solution was titrated with base to neutral pH. The two-stage titration data were used to calculate the formation number of indium hydroxide colloid, which was found to equal n-bar OH = 2.8. (author)

DOUBLE-SHELL TANK (DST) HYDROXIDE DEPLETION MODEL FOR CARBON DIOXIDE ABSORPTION

International Nuclear Information System (INIS)

OGDEN DM; KIRCH NW

2007-01-01

This document generates a supernatant hydroxide ion depletion model based on mechanistic principles. The carbon dioxide absorption mechanistic model is developed in this report. The report also benchmarks the model against historical tank supernatant hydroxide data and vapor space carbon dioxide data. A comparison of the newly generated mechanistic model with previously applied empirical hydroxide depletion equations is also performed

Fluorometric determination of samarium and europium in rare earth minerals with. beta. -diketoneternary complex

Energy Technology Data Exchange (ETDEWEB)

Huang, H; Hiraki, K; Nishikawa, Y [Kinki Univ., Higashi-Osaka, Osaka (Japan). Faculty of Science and Technology

1981-07-01

This communication reported the optimum conditions for the fluorometric determination of these ions, and the method was adopted in the simultaneous determination of samarium and europium in xenotime and monazite minerals. From the experimental results on the effect of diverse ions and the extraction pH of the aqueous phase, it became clear that TTA-TOPO hexane method was the best system for the determination of samarium and europium because of the highest fluorescence sensitivity of the ternary complex, and also because the lower extraction pH eliminated the effect of diverse ions. Moreover, the very high detection limit (2 ppb) of Sm was achieved by the use of a red sensitive photomultiplier. Which was used at 644 nm, and that of Eu (0.02 ppb) at 614 nm. The procedure was established as follows: The rare earth minerals (xenotime, monazite) sample was treated with hot conc. H/sub 2/SO/sub 4/ and twice precipitated with 0.5 mol dm/sup -3/ oxalic acid (pH was adjusted to 2.0 -- 2.2). Then the precipitate was filtered and ignited to give the rare earth oxide. Fifty milligrams of the oxide was dissolved in HCl and diluted with water in order to obtain the solution containing 5 ..mu..g cm/sup -3/ rare earth oxide. An aliquot of the solution ((1.0 -- 3.0) cm/sup 3/) was adjusted to pH 5.5 with sodium acetate and shaken with 1 x 10/sup -4/ mol dm/sup -3/ TTA- 2 x 10/sup -2/ mol dm/sup -3/ TOPO hexane solution. Then the fluorescence intensity of the organic layer was measured at 644 nm for Sm and 614 nm for Eu. In this procedure, the recovery of Sm and Eu was found to be about 96%. Xenotime contained 0.70% of Sm and 0.004% of Eu, and monazite contained 1.84% of Sm and 0.003% of Eu.

Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

International Nuclear Information System (INIS)

Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E.

2014-01-01

Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH) 3 ·3H 2 O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH) 3 (am) was stable with a solubility lower than 50 μg/l in the range 5.7 0.75 Cr 0.25 (OH) 3 , the stability region was extended to 4.8 3 ·xH 2 O whereas in the presence of iron the precipitate is a mixed Fe (1−x) Cr x (OH) 3 phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe x ,Cr 1−x )(OH) 3 hydroxides as compared to the stability of Cr(OH) 3 . We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH) 3 ·3H 2 O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH) 3 (am) phase. Mixed Fe 0.75 Cr 0.25 (OH) 3 hydroxides were found to be of the ferrihydrite structure, Fe(OH) 3 , and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe(III)–Cr(III) hydroxides are more effective enhancers of groundwater quality, in comparison to the plain amorphous or crystalline Cr(III) hydroxides, the latter found to have a solubility typically higher than 50 μg/l (maximum EU permitted Cr level in drinking water), while the amorphous Cr(OH) 3 (am) phase was within the drinking water threshold in the range 5.7 0.75 Cr 0.25 (OH) 3 hydroxides studied were of extended stability in the 4.8 < pH < 13.5 range

HYDROGEN PEROXIDE BLEACHING OF CMP PULP USING MAGNESIUM HYDROXIDE

Directory of Open Access Journals (Sweden)

Farhad Zeinaly

2009-11-01

Full Text Available Conventional bleaching of hardwood CMP pulp with magnesium hydroxide (Mg(OH2 show significant benefits over bleaching with sodium hydroxide (NaOH under various conditions. Magnesium hydroxide bleaching generate higher optical properties, higher pulp yield and lower effluent COD at the same chemical charge, but the physical properties were found to be similar for both processes. The initial freeness of the bleached pulps and refining value to reach a target freeness (about 350 ml. CSF were more for the Mg(OH2-based process. The residual peroxide of filtrate from the Mg(OH2-based process was very high as compared to conventional bleaching.

Thermodynamic Properties of Alkali Metal Hydroxides. Part II. Potassium, Rubidium, and Cesium Hydroxides

International Nuclear Information System (INIS)

Gurvich, L.V.; Bergman, G.A.; Gorokhov, L.N.; Iorish, V.S.; Leonidov, V.Y.; Yungman, V.S.

1997-01-01

The data on thermodynamic and molecular properties of the potassium, rubidium and cesium hydroxides have been collected, critically reviewed, analyzed, and evaluated. Tables of the thermodynamic properties [C p circ , Φ=-(G -H(0)/T, S, H -H(0), Δ f H, Δ f G)] of these hydroxides in the condensed and gaseous states have been calculated using the results of the analysis and some estimated values. The recommendations are compared with earlier evaluations given in the JANAF Thermochemical Tables and Thermodynamic Properties of Individual Substances. The properties considered are: the temperature and enthalpy of phase transitions and fusion, heat capacities, spectroscopic data, structures, bond energies, and enthalpies of formation at 298.15 K. The thermodynamic functions in solid, liquid, and gaseous states are calculated from T=0 to 2000 K for substances in condensed phase and up to 6000 K for gases. copyright 1997 American Institute of Physics and American Chemical Society

Ion-exchange synthesis of compounds based on low-water niobium hydroxide

International Nuclear Information System (INIS)

Ivanova, N.E.; Sakharov, V.E.; Korovin, S.S.

1977-01-01

Ordinary physico-chemical methods have been used for studying the possibilities of the ion-exchange synthesis of niobates of alkaline and alkaline-earth elements based on low-water niobium hydroxide small at relatively low temperatures. It has been established that cation-exchange properties of low-water niobium hydroxide are revealed in a wide range of pH (from 8.95 to 12.4 for alkaline-earth elements and from 6.7 to 12.0 for alkaline elements). Physico-chemical study of solid phases points that there is a monophase with low-water niobium hydroxide. The rate of crystallization ageing of amorphous phases based on low-water niobium hydroxide is rather small for the samples with a M:Nb ratio less than 1.0 whereas mixed hydroxides with M:Nb ratio more than 1.0 reveal on X-ray diffraction patterns diffusion reflections after keeping in mother liquor for 5 hours-1 day

The citotoxicity of calcium hydroxide intracanal dressing by MTT assay

Directory of Open Access Journals (Sweden)

Nanik Zubaidah

2007-12-01

Full Text Available Calcium hydroxide had been used as the intracanal dressing in endodontic treatment due to its high alkaline and high antimicrobial capacity. It also be able to dissolve the necrotic tissue, prevent the root resorbtion and regenerate a new hard tissue. The aim of this study is to identify the concentration of calcium hydroxide that has the lowest citotoxicity. There are 5 groups, each group had 8 samples with different concentration of calcium hydroxide. Group I: 50%, Group II: 55%, Group III: 60%, Group IV: 65% and Group V: 70%. The citotoxicity test by using enzymatic assay of MTT [3-(4.5- dimethylthiazol-2yl ]-2.5 diphenyl tetrazolium bromide, against fibroblast cell (BHK-21. The result of susceptibility test was showed by the citotoxicity detection of the survive cell of fibroblast that was measured spectrophotometrically using 595 nm beam. The data was analyzed using One-Way ANOVA test with significant difference α = 0.05 and subsequently LSD test. The result showed that in concentration 50%, 55%, 60%, 65%, and 70% calcium hydroxide had low toxicity, but calcium hydroxide 60%, had the lowest toxicity.

Sorption of chromium(VI) and chromium(III) on aluminium hydroxide

International Nuclear Information System (INIS)

Music, S.

1986-01-01

Factors that influence the sorption of Cr(VI) and Cr(III) on aluminium hydroxide were investigated. The sorption of chromates decreases as the pH of the suspension increases. The mechanism of CrOsub(4)sup(2-) sorption was interpreted in terms of reactions between chromates and -OH and/or Hsub(2)O groups at the hydroxide/liquid interface. It was shown that chromates are more tightly sorbed on aluminium hydroxide compared to other anions, e.g. chlorides. On the other hand, specifically absorbed anions, such as molybdates, compete strongly with chromates for the sorption sites. The sorption of chromium(III) increases with the pH of the suspension. Also, the sorption of chromium(III) is suppressed in the presence of citrate ions. The best conditions for the fixation of Cr(VI) and Cr(III) by aluminium hydroxide are presented. (author)

Crystallite size effects in stacking faulted nickel hydroxide and its electrochemical behaviour

International Nuclear Information System (INIS)

Ramesh, T.N.

2009-01-01

β-Nickel hydroxide comprises a long range periodic arrangement of atoms with a stacking sequence of AC AC AC-having an ideal composition Ni(OH) 2 . Variation in the preparative conditions can lead to the changes in the stacking sequence (AC AC BA CB AC AC or AC AC AB AC AC). This type of variation in stacking sequence can result in the formation of stacking fault in nickel hydroxide. The stability of the stacking fault depends on the free energy content of the sample. Stacking faults in nickel hydroxide is essential for better electrochemical activity. Also there are reports correlating particle size to the better electrochemical activity. Here we present the effect of crystallite size on the stacking faulted nickel hydroxide samples. The electrochemical performance of stacking faulted nickel hydroxide with small crystallite size exchanges 0.8e/Ni, while the samples with larger crystallite size exchange 0.4e/Ni. Hence a right combination of crystallite size and stacking fault content has to be controlled for good electrochemical activity of nickel hydroxide

Synthesis of hydroxide type sorbents from industry high-iron wastes

International Nuclear Information System (INIS)

Stepanenko, E.K.; Smirnov, A.L.

1986-01-01

Article presents the results of studies on possibility of using of technological iron containing wastes for the obtaining of hydroxide type sorbents in granular form. The scheme of technology of synthesis of hydroxide type sorbents from high-iron wastes is elaborated.

Hydroxide catalysts for lignin depolymerization

Science.gov (United States)

Beckham, Gregg T; Biddy, Mary J.; Kruger, Jacob S.; Chmely, Stephen C.; Sturgeon, Matthew

2017-10-17

Solid base catalysts and their use for the base-catalyzed depolymerization (BCD) of lignin to compounds such as aromatics are presented herein. Exemplary catalysts include layered double hydroxides (LDHs) as recyclable, heterogeneous catalysts for BCD of lignin.

Hydroxide catalysts for lignin depolymerization

Energy Technology Data Exchange (ETDEWEB)

Beckham, Gregg T.; Biddy, Mary J.; Chmely, Stephen C.; Sturgeon, Matthew

2017-04-25

Solid base catalysts and their use for the base-catalyzed depolymerization (BCD) of lignin to compounds such as aromatics are presented herein. Exemplary catalysts include layered double hydroxides (LDHs) as recyclable, heterogeneous catalysts for BCD of lignin.

Concentration of 99Tc in seawater by coprecipitation with iron hydroxide

International Nuclear Information System (INIS)

Momoshima, Noriyuki; Eto, Ichiro; Muhammad Sayad; Takashima, Yoshimasa

1991-01-01

A method for accumulation of 99 Tc in seawater has been developed. Technetium tracer in +VII oxidation state was added to the seawater together with reducing agent, potassium pyrosulfite, and coprecipitation agent, ferric chloride. After reduction of Tc(VII) at pH 4, Tc(IV) was coprecipitated as iron hydroxide by addition of sodium hydroxide to pH 9. The reduction and coprecipitation was quantitative and overall recovery of Tc was more than 98%. The green color of iron precipitate formed at pH 9 suggested that Tc(VII) as well as ferric ion was reduced under this condition. Adsorption of Tc(IV), however, was poor for iron hydroxide which was prepared in advance indicating active surface of freshly precipitated iron hydroxide is necessary for quantitative recovery of Tc(IV). A repeating coprecipitation technique was examined for enrichment of Tc in seawater that the same iron was used repeatedly as coprecipitater. After separation of iron hydroxide with Tc(IV) from supernatant, the precipitate was dissolved by addition of acid and then new seawater which contained reducing agent and Tc(VII) was added. Reduction and coprecipitation was again carried out. Good recovery was attained for 7 repeats. The proposed repeating coprecipitation technique was applicable to a large amount of seawater without increasing the amount of iron hydroxide which is subjected to radiochemical analysis. (author)

Synthesis of aluminum oxy-hydroxide nanofibers from porous anodic alumina

Energy Technology Data Exchange (ETDEWEB)

Jha, Himendra; Kikuchi, Tatsuya; Sakairi, Masatoshi; Takahashi, Hideaki [Laboratory of Interface Microstructure Analysis (LIMSA), Division of Materials Science and Engineering, Graduate School of Engineering, Hokkaido University, Sapporo 060-8628 (Japan)], E-mail: himendra@eng.hokudai.ac.jp

2008-10-01

A novel method for the synthesis of aluminum oxy-hydroxide nanofibers from a porous anodic oxide film of aluminum is demonstrated. In the present method, the porous anodic alumina not only acts as a template, but also serves as the starting material for the synthesis. The porous anodic alumina film is hydrothermally treated for pore-sealing, which forms aluminum oxy-hydroxide inside the pores of the oxide film as well as on the surface of the film. The hydrothermally sealed porous oxide film is immersed in the sodium citrate solution, which selectively etches the porous aluminum oxide from the film, leaving the oxy-hydroxide intact. The method is simple and gives highly uniform aluminum oxy-hydroxide nanofibers. Moreover, the diameter of the nanofibers can be controlled by controlling the pore size of the porous anodic alumina film, which depends on the anodizing conditions. Nanofibers with diameters of about 38-85 nm, having uniform shape and size, were successfully synthesized using the present method.

Synthesis of aluminum oxy-hydroxide nanofibers from porous anodic alumina

International Nuclear Information System (INIS)

Jha, Himendra; Kikuchi, Tatsuya; Sakairi, Masatoshi; Takahashi, Hideaki

2008-01-01

A novel method for the synthesis of aluminum oxy-hydroxide nanofibers from a porous anodic oxide film of aluminum is demonstrated. In the present method, the porous anodic alumina not only acts as a template, but also serves as the starting material for the synthesis. The porous anodic alumina film is hydrothermally treated for pore-sealing, which forms aluminum oxy-hydroxide inside the pores of the oxide film as well as on the surface of the film. The hydrothermally sealed porous oxide film is immersed in the sodium citrate solution, which selectively etches the porous aluminum oxide from the film, leaving the oxy-hydroxide intact. The method is simple and gives highly uniform aluminum oxy-hydroxide nanofibers. Moreover, the diameter of the nanofibers can be controlled by controlling the pore size of the porous anodic alumina film, which depends on the anodizing conditions. Nanofibers with diameters of about 38-85 nm, having uniform shape and size, were successfully synthesized using the present method

Mixing Acid Salts and Layered Double Hydroxides in Nanoscale under Solid Condition.

Science.gov (United States)

Nakayama, Hirokazu; Hayashi, Aki

2014-07-30

The immobilization of potassium sorbate, potassium aspartate and sorbic acid in layered double hydroxide under solid condition was examined. By simply mixing two solids, immobilization of sorbate and aspartate in the interlayer space of nitrate-type layered double hydroxide, so called intercalation reaction, was achieved, and the uptakes, that is, the amount of immobilized salts and the interlayer distances of intercalation compounds were almost the same as those obtained in aqueous solution. However, no intercalation was achieved for sorbic acid. Although intercalation of sorbate and aspartate into chloride-type layered double hydroxide was possible, the uptakes for these intercalation compounds were lower than those obtained using nitrate-type layered double hydroxide. The intercalation under solid condition could be achieved to the same extent as for ion-exchange reaction in aqueous solution, and the reactivity was similar to that observed in aqueous solution. This method will enable the encapsulation of acidic drug in layered double hydroxide as nano level simply by mixing both solids.

Mixing Acid Salts and Layered Double Hydroxides in Nanoscale under Solid Condition

Directory of Open Access Journals (Sweden)

Hirokazu Nakayama

2014-07-01

Full Text Available The immobilization of potassium sorbate, potassium aspartate and sorbic acid in layered double hydroxide under solid condition was examined. By simply mixing two solids, immobilization of sorbate and aspartate in the interlayer space of nitrate-type layered double hydroxide, so called intercalation reaction, was achieved, and the uptakes, that is, the amount of immobilized salts and the interlayer distances of intercalation compounds were almost the same as those obtained in aqueous solution. However, no intercalation was achieved for sorbic acid. Although intercalation of sorbate and aspartate into chloride-type layered double hydroxide was possible, the uptakes for these intercalation compounds were lower than those obtained using nitrate-type layered double hydroxide. The intercalation under solid condition could be achieved to the same extent as for ion-exchange reaction in aqueous solution, and the reactivity was similar to that observed in aqueous solution. This method will enable the encapsulation of acidic drug in layered double hydroxide as nano level simply by mixing both solids.

[Antimicrobial effect of various calcium hydroxide on Porphyromonas endodontalis in vitro].

Science.gov (United States)

Du, Ting-ting; Qiu, Li-hong; Jia, Ge; Yang, Di; Guo, Yan

2012-04-01

To compare the antimicrobial activity of Endocal, calcium hydroxide paste, Calxyl, Vitapex on Porphyromonas endodontalis(P.e). (1) The antimicrobial activity of different calcium hydroxide on P.e was examined at different exposure times by dynamic nephelometry. (2) 85 freshly extracted single-rooted human teeth were selected and cut at the amelocemental junction. All roots were randomly divided into five groups. The bacteria were incubated in each canal and were sampled and counted before and after enveloping five kinds of intercanal medicine seeded. Student's t test, One-way ANOVA were used with SPSS11.0 software package for statistical analysis. The bacteria from each group were reduced significantly after intracanal medication (P<0.05). The antibacterial efficacy of Endocal and calcium hydroxide paste were superior to others under dynamic nephelometry test (P<0.05). Endocal, calcium hydroxide paste, Calxyl, Vitapex had strong inhibitory effect on P.e from infected root canals, and the rate of bacteria clearance was 95%. The antimicrobial activity of Endocal was significantly greater than others (P<0.05). Endocal, calcium hydroxide paste, Calxyl and Vitapex were effective for intercanal disinfection. The antibacterial activity of Endocal is greater than Vitapex.

The properties of samarium-doped zinc oxide/phthalocyanine structure for optoelectronics prepared by pulsed laser deposition and organic molecular evaporation

Czech Academy of Sciences Publication Activity Database

Novotný, Michal; Marešová, Eva; Fitl, Přemysl; Vlček, Jan; Bergmann, M.; Vondráček, Martin; Yatskiv, Roman; Bulíř, Jiří; Hubík, Pavel; Hruška, Petr; Drahokoupil, Jan; Abdellaoui, N.; Vrňata, M.; Lančok, Ján

2016-01-01

Roč. 122, č. 3 (2016), 1-8, č. článku 225. ISSN 0947-8396 R&D Projects: GA MŠk(CZ) LG15050; GA ČR(CZ) GAP108/11/0958; GA MŠk(CZ) LM2011029; GA ČR(CZ) GA14-10279S; GA MŠk(CZ) 7AMB14FR010 Institutional support: RVO:68378271 ; RVO:67985882 Keywords : samarium-doped zinc oxide zinc/phthalocyanine deposition * evaporation * pulsed laser deposition * thin films Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.455, year: 2016

Cross sections for d-{sup 3}H neutron interactions with samarium isotopes

Energy Technology Data Exchange (ETDEWEB)

Luo, Junhua; He, Long [Hexi Univ., Zhangye (China). School of Physics and Electromechanical Engineering; Wu, Chunlei; Jiang, Li [Chinese Academy of Engineering Physics, Mianyang (China). Inst. of Nuclear Physics and Chemistry

2016-11-01

The cross sections for (n,x) reactions on samarium isotopes were measured at (d-T) neutron energies of 13.5 and 14.8 MeV with the activation technique. Samples were activated along with Nb and Al monitor foils to determine the incident neutron flux. Theoretical calculations of excitation functions were performed using the nuclear model codes TALYS-1.6 and EMPIRE-3.2 Malta with default parameters, at neutron energies varying from the reaction threshold to 20 MeV. The results were discussed and compared with experimental data found in the literature. At neutron energies 13.5 and 14.8 MeV, the cross sections of the {sup 149}Sm(n,p){sup 149}Pm reaction are reported for the first time. The cross sections of the {sup 150}Sm(n,p){sup 150}Pm, {sup 144}Sm(n,p){sup 144}Pm, {sup 152}Sm(n,α){sup 149}Nd and {sup 144}Sm(n,α){sup 141}Nd reactions at different neutron energies reported in the present work can be added as new data in the nuclear databases.

Charge and transition densities of samarium isotopes in the interacting Boson model

International Nuclear Information System (INIS)

Moinester, M.A.; Alster, J.; Dieperink, A.E.L.

1982-01-01

The interacting boson approximation (IBA) model has been used to interpret the ground-state charge distributions and lowest 2 + transition charge densities of the even samarium isotopes for A = 144-154. Phenomenological boson transition densities associated with the nucleons comprising the s-and d-bosons of the IBA were determined via a least squares fit analysis of charge and transition densities in the Sm isotopes. The application of these boson trasition densities to higher excited 0 + and 2 + states of Sm, and to 0 + and 2 + transitions in neighboring nuclei, such as Nd and Gd, is described. IBA predictions for the transition densities of the three lowest 2 + levels of 154 Gd are given and compared to theoretical transition densities based on Hartree-Fock calculations. The deduced quadrupole boson transition densities are in fair agreement with densities derived previously from 150 Nd data. It is also shown how certain moments of the best fit boson transition densities can simply and sucessfully describe rms radii, isomer shifts, B(E2) strengths, and transition radii for the Sm isotopes. (orig.)

Preparation of a sinterable beryllium oxide through decomposition of beryllium hydroxide (1963)

International Nuclear Information System (INIS)

Bernier, M.

1963-01-01

In the course of the present study, we have attempted to precise the factors which among the ones effective in the course of the preparation of the beryllium hydroxide and oxide and during the sintering have an influence on the final result: the density and homogeneity of the sintered body. Of the several varieties of hydroxides precipitated from a sulfate solution the β-hydroxide only is always contaminated with beryllium sulfate and cannot be purified even by thorough washing. We noticed that those varieties of the hydroxide (gel, α, β) have different decomposition rates; this behaviour is used to identify and even to dose the different species in (α, β) mixtures. The various hydroxides transmit to the resulting oxides the shape they had when precipitated. Accordingly the history of the oxide is revealed by its behaviour during its fabrication and sintering. By comparing the results of the sintering operation with the various measurements performed on the oxide powders we are led to the conclusion that an oxide obtained from beryllium hydroxide is sinterable under vacuum if the following conditions are fulfilled: the particle size must lie between 0.1 and 0.2 μ and the BeSO 4 content of the powder must be less than 0.25 per cent wt (expressed as SO 3 /BeO). The best fitting is obtained with the oxide issued from an α-hydroxide precipitated as very small aggregates and with a low sulfur-content. We have observed that this is also the case for the oxide obtained by direct calcination of beryllium sulfate. (author) [fr

Thermodynamics of coproportionation reactions of homogeneous samarium (3) and yttrium (3) nitrates solvates with neutral organic phosphorus compounds

International Nuclear Information System (INIS)

Pyartman, A.K.

1995-01-01

Reaction heats of homogeneous samarium (3) and yttrium (3) nitrate solvates coproportionation with neutral organophosphoric compounds (tri-n.-butylphosphate, diisooctylmethylphosphonate, diisoamylmethylphosphonate) at T=298.15 K in hexane have been measured by thermochemical method. It has been ascertained that enthalpies of coproportionation reactions practically do not depend on the nature, concentration of rare earth metal (3) nitrate solvates in hexane, nature of neutral organophosphoric compound and constitute 1.1±-.2 kJ/mol. The Gibbs free energy of coproportionation reactions is -5.43 kJ/mol, while entropy of the reactions in 14.5±0.7 J/mol·K. 8 refs., 1 tab

Comparative evaluation of different forms of calcium hydroxide in apexification

Directory of Open Access Journals (Sweden)

Subhankar Ghosh

2014-01-01

Full Text Available Background: One out of every two children sustains a dental injury most often between 8 and 10 years of age. Majority of these teeth subsequently become non-vital and most often with immature apex. Management of these teeth is an enormous challenge for lack of apical stop. Calcium hydroxide in various formulations has maximum literature support in favor of "successful apexification or induced apical closure." Aim: The aim of the following study is to determine the efficacy of calcium hydroxide in a different formulation to induce apexification. Materials and Methods: The present study was undertaken on 51 children of 8-10 years of age (both sexes at Dr. R Ahmed Dental College and Hospital from April 2006 to March 2007. All children had one or two maxillary permanent central incisor (s, non-vital and apices open. In all the cases, apexification was attempted with either calcium hydroxide mixed with sterile distilled water, or calcium hydroxide plus iodoform in methyl cellulose base, or calcium hydroxide plus iodoform in polysilicone oil base. The success of apexification was determined on the basis of clinical and radiographic criteria. Results: In the pre-operative asymptomatic cases (72.55%, failure occurred in only 5.45% cases and pre-operative symptomatic cases failure rate was as high as 35.71%. Success rate was 94.6% in cases with narrow open apices, whereas 64.28% in wide open apices. In cases with pre-existing apical radiolucencies, successful apexification occurred in 63.63% and success rate was 92.5% in the cases without pre-existing apical radiolucencies. Average time consumed for apexification was minimum with calcium hydroxide plus iodoform in polysilicone oil base. Conclusion: The overall success rate observed to be 86.27%, which is in close proximity to the findings of most of the previous studies across the globe.

Comparative evaluation of different forms of calcium hydroxide in apexification.

Science.gov (United States)

Ghosh, Subhankar; Mazumdar, Dibyendu; Ray, Pradip Kumar; Bhattacharya, Bhaswar

2014-01-01

One out of every two children sustains a dental injury most often between 8 and 10 years of age. Majority of these teeth subsequently become non-vital and most often with immature apex. Management of these teeth is an enormous challenge for lack of apical stop. Calcium hydroxide in various formulations has maximum literature support in favor of successful apexification or induced apical closure. The aim of the following study is to determine the efficacy of calcium hydroxide in a different formulation to induce apexification. The present study was undertaken on 51 children of 8-10 years of age (both sexes) at Dr. R Ahmed Dental College and Hospital from April 2006 to March 2007. All children had one or two maxillary permanent central incisor (s), non-vital and apices open. In all the cases, apexification was attempted with either calcium hydroxide mixed with sterile distilled water, or calcium hydroxide plus iodoform in methyl cellulose base, or calcium hydroxide plus iodoform in polysilicone oil base. The success of apexification was determined on the basis of clinical and radiographic criteria. In the pre-operative asymptomatic cases (72.55%), failure occurred in only 5.45% cases and pre-operative symptomatic cases failure rate was as high as 35.71%. Success rate was 94.6% in cases with narrow open apices, whereas 64.28% in wide open apices. In cases with pre-existing apical radiolucencies, successful apexification occurred in 63.63% and success rate was 92.5% in the cases without pre-existing apical radiolucencies. Average time consumed for apexification was minimum with calcium hydroxide plus iodoform in polysilicone oil base. The overall success rate observed to be 86.27%, which is in close proximity to the findings of most of the previous studies across the globe.

Functionalization of lanthanum hydroxide nanowires by atom transfer radical polymerization

International Nuclear Information System (INIS)

Zhou Mi; Yuan Jinying; Yuan Weizhong; Yin Yingwu; Hong Xiaoyin

2007-01-01

Atom transfer radical polymerization (ATRP) has been used to prepare a core-shell hybrid nanostructure successfully: a hard core of single-crystalline lanthanum hydroxide nanowires and a soft shell of polystyrene (PS) brushes. Transmission electron microscopy (TEM) images indicated that the resulting products presented special structures and different thicknesses of polymer layers. The chemical components and grafted PS quantities of the samples were measured by Fourier transform infrared (FT-IR) spectroscopy and thermogravimetric analysis (TGA). The polymers showed narrow polydispersity, which proved that the lanthanum hydroxide nanowires initiated the 'living'/controlled polymerization of styrene. With the modifiability of lanthanum hydroxide nanowires, the solubility increased, which affords a new way to functionalize nanowires

Structural perturbation of diphtheria toxoid upon adsorption to aluminium hydroxide adjuvant

NARCIS (Netherlands)

Regnier, M.; Metz, B.; Tilstra, W.; Hendriksen, C.; Jiskoot, W.; Norde, W.; Kersten, G.

2012-01-01

Aluminium-containing adjuvants are often used to enhance the potency of vaccines. In the present work we studied whether adsorption of diphtheria toxoid to colloidal aluminium hydroxide induces conformational changes of the antigen. Diphtheria toxoid has a high affinity for the aluminium hydroxide

Effect of calcium hydroxide on slip casting behaviour

OpenAIRE

Şakar‐Deliormanlı, Aylin; Yayla, Zeliha

2004-01-01

The effect of calcium hydroxide addition on the casting performance of ceramic slips for sanitary ware was studied. Powder composed of feldspar (24 wt.%), quartz (24 wt.%), kaolin (35 wt.%) and ball clay (17 wt.%) was mixed with water to contain 65 wt.% of solids (specific density 1800 g/l). Either Ca(OH)2 or Na2CO3 was added at concentrations ranging between 0.060 and 0.085 wt.% and the slurries were dispersed by the optimum addition of sodium silicate. Calcium hydroxide in presence of sodiu...

Synthesis of Zn–Fe layered double hydroxides via an oxidation process and structural analysis of products

Energy Technology Data Exchange (ETDEWEB)

Morimoto, Kazuya, E-mail: kazuya.morimoto@aist.go.jp [Institute for Geo-Resources and Environment, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Higashi, Tsukuba, Ibaraki 305-8567 (Japan); Tamura, Kenji [Environmental Remediation Materials Unit, National Institute for Materials Science (NIMS), 1-1 Namiki, Tsukuba, Ibaraki 305-0044 (Japan); Anraku, Sohtaro [Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan); Sato, Tsutomu [Faculty of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan); Suzuki, Masaya [Institute for Geo-Resources and Environment, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Higashi, Tsukuba, Ibaraki 305-8567 (Japan); Yamada, Hirohisa [Environmental Remediation Materials Unit, National Institute for Materials Science (NIMS), 1-1 Namiki, Tsukuba, Ibaraki 305-0044 (Japan)

2015-08-15

The synthesis of Zn–Fe(III) layered double hydroxides was attempted, employing different pathways using either Fe(II) or Fe(III) species together with Zn as the initial reagents. The product derived from the synthesis employing Fe(II) was found to transition to a Zn–Fe(III) layered double hydroxides phase following oxidation process. In contrast, the product obtained with Fe(III) did not contain a layered double hydroxides phase, but rather consisted of simonkolleite and hydrous ferric oxide. It was determined that the valency of the Fe reagent used in the initial synthesis affected the generation of the layered double hydroxides phase. Fe(II) species have ionic radii and electronegativities similar to those of Zn, and therefore are more likely to form trioctahedral hydroxide layers with Zn species. - Graphical abstract: The synthesis of Zn–Fe(III) layered double hydroxides was attempted, employing different pathways using either Fe(II) or Fe(III) species together with Zn as the initial reagents. - Highlights: • Iron valency affected the generation of Zn–Fe layered double hydroxides. • Zn–Fe layered double hydroxides were successfully synthesized using Fe(II). • Fe(II) species were likely to form trioctahedral hydroxide layers with Zn species.

Vibrational dynamics of aqueous hydroxide solutions probed using broadband 2DIR spectroscopy

International Nuclear Information System (INIS)

Mandal, Aritra; Tokmakoff, Andrei

2015-01-01

We employed ultrafast transient absorption and broadband 2DIR spectroscopy to study the vibrational dynamics of aqueous hydroxide solutions by exciting the O–H stretch vibrations of the strongly hydrogen-bonded hydroxide solvation shell water and probing the continuum absorption of the solvated ion between 1500 and 3800 cm −1 . We observe rapid vibrational relaxation processes on 150–250 fs time scales across the entire probed spectral region as well as slower vibrational dynamics on 1–2 ps time scales. Furthermore, the O–H stretch excitation loses its frequency memory in 180 fs, and vibrational energy exchange between bulk-like water vibrations and hydroxide-associated water vibrations occurs in ∼200 fs. The fast dynamics in this system originate in strong nonlinear coupling between intra- and intermolecular vibrations and are explained in terms of non-adiabatic vibrational relaxation. These measurements indicate that the vibrational dynamics of the aqueous hydroxide complex are faster than the time scales reported for long-range transport of protons in aqueous hydroxide solutions

Variation in photoreactivity of iron hydroxides taken from an acidic mountain stream

International Nuclear Information System (INIS)

Hrncir, D.C.; McKnight, D.

1998-01-01

The photoreduction of iron hydroxides is known to exert significant influence over many biogeochemical processes in streams impacted by acid main drainage. Using laboratory and in-stream measurements, the variation in reactivity of iron hydroxides taken from a stream receiving acid mine drainage (AMD) was studied. The reactivity decreased for material collected at sites progressively downstream from the AMD inflow. In the presence of two simple organic ligands, photoreduction increased for the fresher iron hydroxides but remained unchanged for the older hydroxides. The importance of ligand coordination to the enhancement of photoreduction in natural waters was further demonstrated in experiments using two types of fulvic acids. In-stream measurements of hydrogen peroxide concentration are consistent with the conclusions drawn from the batch experiments. Iron hydroxides were observed to age over time, becoming less photoreactive. This aging was accompanied by an increase in crystallinity. The loss of photoreactivity for the older material can be explained by a decrease in the number of active surface sites, a change in the nature of the surface sites, or a combination of both

Efficacy and safety of topical application of 15% and 10% potassium hydroxide for the treatment of Molluscum contagiosum.

Science.gov (United States)

Teixidó, Concepció; Díez, Olga; Marsal, Josep R; Giner-Soriano, Maria; Pera, Helena; Martinez, Mireia; Galindo-Ortego, Gisela; Schoenenberger, Joan A; Real, Jordi; Cruz, Ines; Morros, Rosa

2018-02-26

Molluscum contagiosum is the most common skin infection in children. One topical treatment used for Molluscum contagiosum is potassium hydroxide. The objective of this study was to compare the efficacy of potassium hydroxide topical treatment at different concentrations with that of placebo in terms of complete clearing of Molluscum contagiosum lesions and to assess the safety and tolerance of potassium hydroxide topical treatment. This was a double-blind randomized clinical trial of three treatments (potassium hydroxide 10%, potassium hydroxide 15%, placebo) applied once daily up to complete clearing of lesions (maximum duration 60 days) in 53 children aged 2-6 years in primary health care pediatric offices in Catalonia, Spain. In the intention-to-treat analysis, potassium hydroxide 10% (58.8%, P = .03) and potassium hydroxide 15% (64.3%, P = .02) had efficacy superior to that of placebo (18.8%). The number of Molluscum contagiosum lesions was significantly reduced with potassium hydroxide 10% and 15%. The main efficacy outcome was achieved in 58.8% of children in the potassium hydroxide 10% group (P = .03 vs placebo) and in 64.3% of children in the potassium hydroxide 15% group (P = .02 vs placebo). Potassium hydroxide 10% and 15% were not significantly different in efficacy from each other. Potassium hydroxide 10% and placebo were better tolerated than potassium hydroxide 15%. No adverse events were reported during the study period. Potassium hydroxide 10% and 15% demonstrated high rates of efficacy in clearing Molluscum contagiosum lesions, with potassium hydroxide 10% being better tolerated. © 2018 Wiley Periodicals, Inc.

COMBINED ALUMINIUM SULFATE/HYDROXIDE PROCESS FOR ...

African Journals Online (AJOL)

sulfate, and used for fluoride removal from water by combining with Nalgonda Technique. ... effects on human health and could result in fluorosis. ... [23], nanoscale aluminium oxide hydroxide (AlOOH) [24] and natural zeolite [25], were among.

F-radiographic study of uranium distribution in iron hydroxides from crusts of weathering

International Nuclear Information System (INIS)

Zhmodik, S.M.; Mironov, A.G.; Nemirovskaya, N.A.

1980-01-01

Presented are the results of study of uranium concentrations and peculiarities of its distribution in iron hydroxides from crusts of weathering of aluminium silicate and carbonate rocks. The age of one crusts of weathering is Quaternary, of others - Tertiary. The effect of climatic conditions, composition of source rocks, hydrochemical zoning of the crust of weathering on the uranium fixation by iron hydroxides has been studied. Gamma-spectroscopy, luminescence and autoradiography methods have been used. The mechanism of formation of increased uranium concentrations in iron hydroxides is considered. A conclusion is made that increased uranium concentrations in iron hydroxides may appear in the process of weathering both of aluminium-silicate and carbonate-containing rocks as a result of uranium sorption by fine dispersed iron hydrates. The use of iron hydroxides with increased (anomalous) uranium concentrations as a direct search feature without additional investigations can lead to wrong conclusions

Alkali metal and alkali metal hydroxide intercalates of the layered transition metal disulfides

International Nuclear Information System (INIS)

Kanzaki, Y.; Konuma, M.; Matsumoto, O.

1981-01-01

The intercalation reaction of some layered transition metal disulfides with alkali metals, alkali metal hydroxides, and tetraalkylammonium hydroxides were investigated. The alkali metal intercalates were prepared in the respective metal-hexamethylphosphoric triamide solutions in vaccuo, and the hydroxide intercalates in aqueous hydroxide solutions. According to the intercalation reaction, the c-lattice parameter was increased, and the increase indicated the expansion of the interlayer distance. In the case of alkali metal intercalates, the expansion of the interlayer distance increased continuously, corresponding to the atomic radius of the alkali metal. On the other hand, the hydroxide intercalates showed discrete expansion corresponding to the effective ionic radius of the intercalated cation. All intercalates of TaS 2 amd NbS 2 were superconductors. The expansion of the interlayer distance tended to increase the superconducting transition temperature in the intercalates of TaS 2 and vice versa in those of NbS 2 . (orig.)

Nickel oxide/hydroxide nanoplatelets synthesized by chemical precipitation for electrochemical capacitors

International Nuclear Information System (INIS)

Wu, M.-S.; Hsieh, H.-H.

2008-01-01

Nickel hydroxide powder prepared by directly chemical precipitation method at room temperature has a nanoplatelet-like morphology and could be converted into nickel oxide at annealing temperature higher than 300 deg. C, confirmed by the thermal gravimetric analysis and X-ray diffraction. Annealing temperature influences significantly both the electrical conductivity and the specific surface area of nickel oxide/hydroxide powder, and consequently determines the capacitor behavior. Electrochemical capacitive behavior of the synthesized nickel hydroxide/oxide film is investigated by cyclic voltammetry and electrochemical impedance spectroscope methods. After 300 deg. C annealing, the highest specific capacitance of 108 F g -1 is obtained at scan rate of 10 mV s -1 . When annealing temperature is lower than 300 deg. C, the electrical conductivity of nickel hydroxide dominates primarily the capacitive behavior. When annealing temperature is higher than 300 deg. C, both electrical conductivity and specific surface area of the nickel oxide dominate the capacitive behavior

Magnesium hydroxide as the neutralizing agent for radioactive hydrochloric acid solutions

International Nuclear Information System (INIS)

Palmer, M.J.; Fife, K.W.

1995-10-01

The current technology at Los Alamos for removing actinides from acidic chloride waste streams is precipitation with approximately 10 M potassium hydroxide. Although successful, there are many inherent drawbacks to this precipitation technique which will be detailed in this paper. Magnesium hydroxide (K sp = 1.3 x 10 -11 ) has limited solubility in water and as a result of the common ion effect, cannot generate a filtrate with a pH greater than 9. At a pH of 9, calcium (K sp = 5.5 x 10 -6 ) will not coprecipitate as the hydroxide. This is an important factor since many acidic chloride feeds to hydroxide precipitation contain significant amounts of calcium. In addition, neutralization with Mg(OH) 2 produces a more filterable precipitate because neutralization occurs as the Mg(OH) 2 is dissolved by the acid rather than as a result of the much faster liquid/liquid reaction of KOH with the waste acid. This slower solid/liquid reaction allows time for crystal growth to occur and produces more easily filterable precipitates. On the other hand, neutralization of spent acid with strong KOH that yields numerous hydroxide ions in solution almost instantaneously forming a much larger volume of small crystallites that result in gelatinous, slow-filtering precipitates. Magnesium hydroxide also offers a safety advantage. Although mildly irritating, it is a weak base and safe and easy to handle. From a waste minimization perspective, Mg(OH) 2 offers many advantages. First, the magnesium hydroxide is added as a solid. This step eliminates the diluent water used in KOH neutralizations. Secondly, because the particle size of the precipitate is larger, more actinides are caught on the filter paper resulting in a smaller amount of actinide being transferred to the TA-50 Liquid Waste Treatment Facility. Third, the amount of solids that must be reprocessed is significantly smaller resulting in less waste generation from the downstream processes

Nickel hydroxide modified electrodes for urea determination

Directory of Open Access Journals (Sweden)

Luiz Henrique Dall´Antonia

2007-03-01

Full Text Available Nickel hydroxide films were prepared by electrodeposition from a solution Ni(NO32 0,05 mol L ?¹ on ITO electrodes (Tin oxide doped with Indium on PET-like plastic film, applying a current of - 0,1 A cm ?² during different time intervals between 1800 and 7200 s. The electrochemical behavior of the nickel hydroxide electrode was investigated through a cyclic voltammogram, in NaOH 1,0 mol L ?¹, where it was observed two peaks in the profile in 0,410 and 0,280 V, corresponding to redox couple Ni(II/Ni(III. A sensor for urea presenting a satisfactory answer can be obtained when, after the deposit of the film of Ni(OH2 on the electrode of nickel, it is immersed in a solution of NaOH 1,0 mol L ?¹ and applying a potential of + 0,435 V, where the maximum of the anodic current occurs in the cyclic voltammogram. Analyzing the results it can be observed that, for a range of analite concentration between 5 to 50 m mol L ?¹, the behavior is linear and the sensibility found was of 20,3 mA cm?² (mol L?¹?¹, presenting reproducibility confirming the nickel hydroxide electrodes utilization for the determination of urea.

Preparation of hydroxide ion conductive KOH–layered double hydroxide electrolytes for an all-solid-state iron–air secondary battery

Directory of Open Access Journals (Sweden)

Taku Tsuneishi

2014-06-01

Full Text Available Anion conductive solid electrolytes based on Mg–Al layered double hydroxide (LDH were prepared for application in an all-solid-state Fe–air battery. The ionic conductivity and the conducting ion species were evaluated from impedance and electromotive force measurements. The ion conductivity of LDH was markedly enhanced upon addition of KOH. The electromotive force in a water vapor concentration cell was similar to that of an anion-conducting polymer membrane. The KOH–LDH obtained was used as a hydroxide ion conductive electrolyte for all-solid-state Fe–air batteries. The cell performance of the Fe–air batteries was examined using a mixture of KOH–LDH and iron-oxide-supported carbon as the negative electrode.

Efficacy and toxicity of Samarium-153-EDTMP locally produced in the treatment of painful skeletal metastases

International Nuclear Information System (INIS)

Olea, E.; Quintana, J.C.; Nagel, J.; Arenas, L.; Tomicic, M.; Gil, M.C.; Araya, G.

2001-01-01

Samarium-153 emits medium-energy beta particles an a gamma photon with a physical half-life of 46,3 hours. When chelated to ethylenediaminetetramethylenephosphonic acid (EDTMP), it is remarkably stable in vitro and in vivo. In this study we administered randomly 0,5 and 1,0 mCi/Kg body weight (two groups), to 30 patients with painful metastatic bone cancer. Slight and spontaneously reversible myelotoxicity was observed. A bigger leukocyte and platelet suppression was obtained with 1,0 mCi/kg than 0,5 mCi/Kg dose. Pain palliation was obtained in 66% of the treated patients. Our preliminary results indicate that 153 Sm-EDTMP is a promising radiotherapeutic agent for palliative treatment of metastatic bone cancer pain where a reactor is available and at a very affordable cost. (author)

The effect of polymers onto the size of zinc layered hydroxide salt and its calcined product

Science.gov (United States)

Hussein, Mohd Zobir bin; Ghotbi, Mohammad Yeganeh; Yahaya, Asmah Hj; Abd Rahman, Mohd Zaki

2009-02-01

Zinc hydroxide nitrate, a brucite-like layered material was synthesized using pH control method. Poly(vinyl alcohol) and poly(ethylene glycol) were used at various percentages as size decreasing agents during the synthesis of zinc hydroxide nitrate. SEM and PXRD showed the decrease of size and thickness of the resultant zinc hydroxide nitrates. TG and surface area data confirmed the decrease of the particle sizes, too. When zinc hydroxide nitrates were heat treated at 500 °C, the physical properties of nano zinc oxides obtained depended on the parent material, zinc hydroxide nitrate.

Determination of the nuclear electric charge distribution of samarium isotopes 144, 148, 150, 152, 154 by the muonic atom method

International Nuclear Information System (INIS)

Barreau, Pierre.

1977-01-01

The theory of the nucleus-negative muon system in the case of electrical interactions is discussed. The interactions of muons with the samarium isotopes 152, 154, 144, 148, 150 are investigated. After a description of the experimental device, from muon beam production to data acquisition (detection of the gamma spectra), the results are analyzed and the nuclear charge distribution parameters determined: for each isotope the absolute value of c (half-density radius) and t (skin thickness); for 152 Sm and 154 Sm the parameter β 2 (quadrupolar defomation). Nuclear polarization was accounted for throughout the analysis [fr

EFFICACY OF DIFFERENT ENDODONTIC IRRIGATION PROTOCOLS IN CALCIUM HYDROXIDE REMOVAL

Directory of Open Access Journals (Sweden)

Elka N. Radeva

2016-10-01

Full Text Available Introduction: Calcium hydroxide is widely used in the field of endodontics as a temporary root canal filling. This medicament significantly increases pH and optimizes the treatment outcome. Its total removal before final obturation is very important. Otherwise it could affect the hermetic filling and respectively the endodontic success. Aim: To evaluate the most effective irrigation protocol of calcium hydroxide removal from root canals. Materials and methods: In this study 36 single root canal teeth were observed. They were randomly divided into three groups (n=10 each group according to the technique applied for calcium hydroxide removal - manual irrigation, irrigation and Revo-S rotary instrumentation; and passive ultrasonic irrigation, and a control group (n=6 – irrigation with distilled water only. After calcium hydroxide removals following the procedures above, teeth were separated longitudinally in a buccal-lingual direction and remnants of medicaments were observed in the apical, middle and coronal part of each tooth. Then all of the specimens were observed using scanning electron microscopy and evaluated by a specified scale. The results have undergone statistical analysis. Results: In the case of calcium hydroxide in the apex and in the middle with highest average is Revo-S, followed by Ultrasonic and irrigation. In the coronal part the highest average belongs to Revo-S, irrigation and Ultrasonic. In all groups the highest average is represented by control group. Conclusion: There is not a universal technique for removal of intracanal medicaments and applying more than one protocol is required.

Hydrothermal synthesis and formation mechanism of hexagonal yttrium hydroxide fluoride nanobundles

International Nuclear Information System (INIS)

Tian, Li; Sun, QiLiang; Zhao, RuiNi; He, HuiLin; Xue, JianRong; Lin, Jun

2013-01-01

Graphical abstract: The formation of yttrium hydroxide fluorides nanobundles can be expressed as a precipitation transformation from cubic NaYF 4 to hexagonal NaYF 4 and to hexagonal Y(OH) 2.02 F 0.98 owing to ion exchange. - Highlights: • Novel Y(OH) 2.02 F 0.98 nanobundles have been successfully prepared by hydrothermal method. • The branched nanobundles composed of numerous oriented-attached nanoparticles has been studied. • The growth mechanism is proposed to be ion exchange and precipitation transformation. - Abstract: This article presents the fabrication of hexagonal yttrium hydroxide fluoride nanobundles via one-pot hydrothermal process, using yttrium nitrate, sodium hydroxide and ammonia fluoride as raw materials to react in propanetriol solvent. The X-ray diffraction pattern clearly reveals that the grown product is pure yttrium hydroxide fluoride, namely Y(OH) 2.02 F 0.98 . The morphology and microstructure of the synthesized product is testified to be nanobundles composed of numerous oriented-attached nanoparticles as observed from the field emission scanning electron microscopy (FESEM). The chemical composition was analyzed by the energy dispersive spectrum (EDS), confirming the phase transformation of the products which was clearly consistent with the result of XRD analysis. It is proposed that the growth of yttrium hydroxide fluoride nanobundles be attributed to ion exchange and precipitation transformation

Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

Energy Technology Data Exchange (ETDEWEB)

Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E., E-mail: gantipas@metal.ntua.gr

2014-01-15

Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH){sub 3}·3H{sub 2}O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH){sub 3}(am) was stable with a solubility lower than 50 μg/l in the range 5.7 < pH < 11. • For mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3}, the stability region was extended to 4.8 < pH < 13.5. -- Abstract: Chromium is a common contaminant of soils and aquifers and constitutes a major environmental problem. In nature, chromium usually exists in the form of two oxidation states, trivalent, Cr(III), which is relatively innocuous for biota and for the aquatic environment, and hexavalent, Cr(VI) which is toxic, carcinogenic and very soluble. Accordingly, the majority of wastewater and groundwater treatment technologies, include a stage where Cr(VI) is reduced to Cr(III), in order to remove chromium from the aqueous phase and bind the element in the form of environmentally stable solid compounds. In the absence of iron the final product is typically of the form Cr(OH){sub 3}·xH{sub 2}O whereas in the presence of iron the precipitate is a mixed Fe{sub (1−x)}Cr{sub x}(OH){sub 3} phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe{sub x},Cr{sub 1−x})(OH){sub 3} hydroxides as compared to the stability of Cr(OH){sub 3}. We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH){sub 3}·3H{sub 2}O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH){sub 3}(am) phase. Mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3} hydroxides were found to be of the ferrihydrite structure, Fe(OH){sub 3}, and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe

Pharmacokinetics of labelled compounds with technetium-99m and samarium-153

International Nuclear Information System (INIS)

Borda O, L.B.; Torres L, M.N.

1997-01-01

The purpose of this investigation was to establish the different pharmacokinetics parameters of the main radiopharmaceuticals labeled with technetium-99m and samarium-153. These parameters could be subsequently used as reference to compare other products with the same use. Mathematical models and a computerized pharmacokinetic program were used to this purpose. A biodistribution study in quadruplicate and/or quintuplicate was conducted for each radiopharmaceutical, data was was obtained in injection dose percentages. The biodistribution study involved the injection of a predetermined dose of the radiopharmaceutical into animals (rats or mice), which were subsequently put away at different time intervals, removing the relevant organs. Activity in each organ was read by means of a well-type NaI scintillation counter, data obtained in activity counts was transformed into injection dose percentages. Based on these percentages, the mathematical model was constructed and the pharmacokinetic parameters were obtained using the computerized program Expo 2 v. 1, which is written in C language and works in windows. Analyzing the results obtained, we can conclude that the use of the Expo 2 v. 1 program for a bi compartmental analysis allowed us to obtain reliable pharmacokinetic parameters which describe what happens in the organism when the radiopharmaceutical passes from the central compartment to the peripheral one and vice versa

Pyroelectric properties and electrical conductivity in samarium doped BiFeO 3 ceramics

KAUST Repository

Yao, Yingbang

2012-06-01

Samarium (Sm 3+) doped BiFeO 3 (BFO) ceramics were prepared by a modified solid-state-reaction method which adopted a rapid heating as well as cooling during the sintering process. The pyroelectric coefficient increased from 93 to 137 μC/m 2 K as the Sm 3+ doping level increased from 1 mol% to 8 mol%. Temperature dependence of the pyroelectric coefficient showed an abrupt decrease above 80 °C in all samples, which was associated with the increase of electrical conductivity with temperature. This electrical conduction was attributed to oxygen vacancy existing in the samples. An activation energy of ∼0.7 eV for the conduction process was found to be irrespective of the Sm 3+ doping level. On the other hand, the magnetic Néel temperature (T N) decreased with increasing Sm 3+ doping level. On the basis of our results, the effects of Sm doping level on the pyroelectric and electrical properties of the BFO were revealed. © 2011 Elsevier Ltd. All rights reserved.

Zinc-stearate-layered hydroxide nanohybrid material as a precursor to produce carbon nanoparticles

International Nuclear Information System (INIS)

Ghotbi, Mohammad Yeganeh; Bagheri, Narjes; Sadrnezhaad, S.K.

2011-01-01

Research highlights: → In this work, a new organic-clay nanohybrid material, in which the organic moiety is intercalated between the inorganic layers, was synthesized using stearate anion as a guest and zinc hydroxide nitrate as an inorganic layered host by ion-exchange technique. Carbon nanoparticles were obtained by heat treating of the nanohybrid material, zinc-stearate-layered hydroxide. The proposed method is very simple, the chemicals used in the synthesis are cheap and the manner is economic and suitable for a large scale production of nano-sized carbon nanoparticles. - Abstract: Zinc-stearate-layered hydroxide nanohybrid was prepared using stearate anion as an organic guest, and zinc layered hydroxide nitrate, as a layered inorganic host by the ion-exchange method. Powder X-ray diffraction patterns and Fourier transform infrared results indicated that the stearate anion was actually intercalated into the interlayer of zinc layered hydroxide nitrate and confirmed the formation of the host-guest nanohybrid material. Also, surface properties data showed that the intercalation process has changed the porosity for the as-prepared nanohybrid material in comparison with that of the parent material, zinc hydroxide nitrate. The nanohybrid material was heat-treated at 600 deg. C under argon atmosphere. Stearate anion was chosen as a carbonaceous reservoir in the nanohybrid to produce carbon nanoparticles after heat-treating of the nanohybrid and subsequently acid washing process.

75 FR 28608 - Calcium Hydroxide; Receipt of Application for Emergency Exemption, Solicitation of Public Comment

Science.gov (United States)

2010-05-21

... ENVIRONMENTAL PROTECTION AGENCY [EPA-HQ-OPP-2010-0411; FRL-8826-7] Calcium Hydroxide; Receipt of... Department of Agriculture to use the pesticide calcium hydroxide (CAS No. 1305-62-0) to treat up to 1,000... Agriculture has requested the Administrator to issue a quarantine exemption for the use of calcium hydroxide...

Efficacy and Safety of Photon Induced Photoacoustic Streaming for Removal of Calcium Hydroxide in Endodontic Treatment

Directory of Open Access Journals (Sweden)

Markus Laky

2018-01-01

Full Text Available Calcium hydroxide removal from the root canal by photon induced photoacoustic streaming (PIPS compared to needle irrigation and irrigation using sonic activation was investigated. Additionally, safety issues regarding apical extrusion were addressed. In endodontic treatment temporary intracanal medication like calcium hydroxide should be completely removed for long term success. For analysis, 60 artificial teeth were prepared, filled with calcium hydroxide, and divided into four groups. The teeth were assigned to needle irrigation, irrigation using a sonic device, PIPS with a lower energy setting (10 mJ, 15 Hz, or PIPS with a higher energy setting (25 mJ/40 Hz. For comparison the weight of each tooth was measured before and after calcium hydroxide incorporation, as well as after removing calcium hydroxide using the four different methods. Regarding safety issues another 24 samples were filled with stained calcium hydroxide and embedded in 0.4% agarose gel. Color changes in the agarose gel due to apical extrusion were digitally analysed using Photoshop. No significant differences were found for calcium hydroxide removal between the two laser groups. Sonic assisted removal and needle irrigation resulted in significant less calcium hydroxide removal than both laser groups, with significantly more calcium hydroxide removal in the ultrasonic group than in the needle irrigation group. For apical extrusion the higher laser (25 mJ/40 Hz group resulted in significant higher color changes of the periapical gel than all other groups. PIPS with the setting of 10 mJ/15 Hz achieved almost complete removal of calcium hydroxide without increasing apical extrusion of the irrigation solution.

Characteristics of Cement Solidification of Metal Hydroxide Waste

Directory of Open Access Journals (Sweden)

Dae-Seo Koo

2017-02-01

Full Text Available To perform the permanent disposal of metal hydroxide waste from electro-kinetic decontamination, it is necessary to secure the technology for its solidification. The integrity tests on the fabricated solidification should also meet the criteria of the Korea Radioactive Waste Agency. We carried out the solidification of metal hydroxide waste using cement solidification. The integrity tests such as the compressive strength, immersion, leach, and irradiation tests on the fabricated cement solidifications were performed. It was also confirmed that these requirements of the criteria of Korea Radioactive Waste Agency on these cement solidifications were met. The microstructures of all the cement solidifications were analyzed and discussed.

Characteristics of cement solidification of metal hydroxide waste

Energy Technology Data Exchange (ETDEWEB)

Koo, Dae Seo; Sung, Hyun Hee; Kim, Seung Soo; Kim, Gye Nam; Choi, Jong Won [Dept. of Decontemination Decommission Technology Development, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2017-02-15

To perform the permanent disposal of metal hydroxide waste from electro-kinetic decontamination, it is necessary to secure the technology for its solidification. The integrity tests on the fabricated solidification should also meet the criteria of the Korea Radioactive Waste Agency. We carried out the solidification of metal hydroxide waste using cement solidification. The integrity tests such as the compressive strength, immersion, leach, and irradiation tests on the fabricated cement solidifications were performed. It was also confirmed that these requirements of the criteria of Korea Radioactive Waste Agency on these cement solidifications were met. The microstructures of all the cement solidifications were analyzed and discussed.

Transformation of zinc hydroxide chloride monohydrate to crystalline zinc oxide.

Science.gov (United States)

Moezzi, Amir; Cortie, Michael; McDonagh, Andrew

2016-04-25

Thermal decomposition of layered zinc hydroxide double salts provides an interesting alternative synthesis for particles of zinc oxide. Here, we examine the sequence of changes occurring as zinc hydroxide chloride monohydrate (Zn5(OH)8Cl2·H2O) is converted to crystalline ZnO by thermal decomposition. The specific surface area of the resultant ZnO measured by BET was 1.3 m(2) g(-1). A complicating and important factor in this process is that the thermal decomposition of zinc hydroxide chloride is also accompanied by the formation of volatile zinc-containing species under certain conditions. We show that this volatile compound is anhydrous ZnCl2 and its formation is moisture dependent. Therefore, control of atmospheric moisture is an important consideration that affects the overall efficiency of ZnO production by this process.

Aluminium hydroxide-the carrier for catalysts coating

International Nuclear Information System (INIS)

Normatov, I.Sh.; Mirsaidov, U.M.

2003-01-01

At present time several methods of receiving aluminium hydroxide are exist. But all they differ by much staging of process connected with preliminary receiving of intermediate compounds, with application of expensive metallic aluminium

Layered double hydroxides

DEFF Research Database (Denmark)

López Rayo, Sandra; Imran, Ahmad; Hansen, Hans Chr. Bruun

2017-01-01

A novel zinc (Zn) fertilizer concept based on Zn doped layered double hydroxides (Zn-doped Mg-Fe-LDHs) has been investigated. Zn-doped Mg-Fe-LDHs were synthetized, their chemical composition was analyzed and their nutrient release was studied in buffered solutions with different pH values. Uptake...... equation showing maximum release at pH 5.2, reaching approximately 45% of the total Zn content. The Zn concentrations in the plants receiving the LDHs were between 2- and 9.5-fold higher than those in plants without Zn addition. A positive effect of the LDHs was also found in soil. This work documents...

Studies on the structural, optical and dielectric properties of samarium coordinated with salicylic acid single crystal

Science.gov (United States)

Singh, Harjinder; Slathia, Goldy; Gupta, Rashmi; Bamzai, K. K.

2018-04-01

Samarium coordinated with salicylic acid was successfully grown as a single crystal by low temperature solution technique using mixed solvent of methanol and water in equal ratio. Structural characterization was carried out by single crystal X-ray diffraction analysis and it crystallizes in centrosymmetric space group P121/c1. FTIR and UV-Vis-NIR spectroscopy confirmed the compound formation and help to determine the mode of binding of the ligand to the rare earth-metal ion. Dielectric constant and dielectric loss have been measured over the frequency range 100 Hz - 30MHz. The decrease in dielectric constant with increases in frequency is due to the transition from interfacial polarization to dipolar polarization. The small value of dielectric constant at higher frequency ensures that the crystal is good candidate for NLO devices. Dielectric loss represents the resistive nature of the material.

Antimicrobial effect of calcium hydroxide as endo intracanal dressing on Streptococcus viridans

Directory of Open Access Journals (Sweden)

Nanik Zubaidah

2008-03-01

Full Text Available Calcium hydroxide had been used as the intra-canal dressing in endodontic treatment due to its high alkaline and antimicrobial capacity. It can also dissolve the necrotic tissue, prevent dental root resorbtion and regenerate a new hard tissue. The aim of this study was to determine the concentration of calcium hydroxide which had the highest antimicrobial effect on Streptococcus viridans. Samples were divided into 5 groups; each group consisted of 8 samples with different concentration of calcium hydroxide. Group I: 50%, group II: 55, Group III: 60%, Group IV: 65%, Group V: 70%. The antimicrobial testing was performed using diffusion method against Streptococcus viridans. The result of susceptibility test was showed by the inhibition zone diameter which measured with caliper (in millimeter. We analyzed the data using One-Way ANOVA test with significant difference 0.05 and subsequently LSD test. The study showed that calcium hydroxide with concentration 60% has the highest antimicrobial effect.

The effects of lithium hydroxide solution on alkali silica reaction gels created with opal

International Nuclear Information System (INIS)

Mitchell, Lyndon D.; Beaudoin, James J.; Grattan-Bellew, Patrick

2004-01-01

The reaction of Nevada opal with calcium hydroxide, potassium hydroxide and lithium hydroxide solutions was investigated. In addition, opal was exposed to a combined solution of these three hydroxides. The progress of the three reactions was followed using X-ray diffraction (XRD), 29 Si nuclear magnetic resonance (NMR) and scanning electron microscopy (SEM). The XRD results indicated the presence of a low-angle peak exclusive to the lithium-based reactions. The NMR results suggested a change in the silicate structure in the presence of lithium. These techniques indicated that the reaction of the alkali with the opal starting material is inhibited and perhaps stopped in the presence of lithium hydroxide. SEM revealed that the morphology of the reaction products on the surface of the reacted opal grains is markedly different invariably. It was concluded that evidence to support the theory of a protective layer exists and that the nature of the layer varies with ion type

Parametric Effect of Sodium Hydroxide and Sodium Carbonate on the Potency of a Degreaser

OpenAIRE

Babatope Abimbola Olufemi

2016-01-01

Experimental and statistical analysis was carried out on the comparative effect of sodium hydroxide and sodium carbonate on the potency of a laboratory produced degreaser in this work. The materials used include; octadecyl benzene sulphonic acid, sodium hydroxide, sodium carbonate, sodium metasilicate, carboxyl methyl cellulose (C.M.C), formadelhyde, perfume, colourant and distilled water. Different samples of degreaser were produced with varying composition of sodium hydroxide and sodium car...

The effect of magnesium hydroxide, hydromagnesite and layered double hydroxide on the heat stability and fire performance of plasticized poly(vinyl chloride)

CSIR Research Space (South Africa)

Molefe, DM

2015-09-01

Full Text Available . The other samples contained, in addition, minor amounts of iron, manganese nickel and calcium as impurities. Table 2. XRF composition analysis data of samples roasted at 1000 C Concentration, wt.% SiO2 Al2O3 Fe2O3 MnO MgO CaO NiO MgAl-LDH 1.59 36.85 0... additives aluminium trihydrate, magnesium hydroxide (MH), hydromagnesite (HM) and layered double hydroxide (LDH) have utility as endothermic flame retardants and smoke suppressants for PVC as well as other polymers (10-14). Their flame retardant action...

40 CFR 415.60 - Applicability; description of the chlorine and sodium or potassium hydroxide production subcategory.

Science.gov (United States)

2010-07-01

... chlorine and sodium or potassium hydroxide production subcategory. 415.60 Section 415.60 Protection of... MANUFACTURING POINT SOURCE CATEGORY Chlor-alkali Subcategory (Chlorine and Sodium or Potassium Hydroxide Production) § 415.60 Applicability; description of the chlorine and sodium or potassium hydroxide production...

Improvement of the process for electrochemical impregnation of nickel hydroxide electrodes

Science.gov (United States)

Comtat, M.; Lafage, B.; Leonardi, J.

1986-01-01

Nickel hydroxide electrodes containing 11g/dsqm hydroxide, with capacities of 3.6 to 3.8 Ah/dsqm were prepared at 353 K by electrochemical impregnation. The reproducibility of the results is obtained by readjusting the pH before each preparation. The control of each electrode is done during two cycles of charge and discharge following the manufacture by a potential relaxation method.

Calculated solubility isotherm of a system of alkaline earth sulfates and hydroxides in water

International Nuclear Information System (INIS)

MOshinskii, A.S.; TIkomirova, K.A.

1986-01-01

Tis paper examines the calculation of the isothermal solubility diagram of a system of alkaline earth sulfates and hydroxides in water which makes it possible to substantiate, to a considerable extent, the natural physicochemical mineralization of natural waters, in particular water from geochemical sources. The present paper investigates the solubility of the equilibrium solid phases of a system of alkaline earth sulfates and hydroxides in water. A projection is shown of the composition prism of the quinary reciprocal system with demarcation of the crystallization areas of each sulfate and hydroxide of the component subsystems. The computational formulas for calculating solubility were derived from the solubility product principle, with allowance for ion activity coefficients in saturated hydroxide solutions

Mg/Al Ordering in Layered Double Hydroxides Revealed by Multinuclear NMR Spectroscopy

DEFF Research Database (Denmark)

Nielsen, Ulla Gro; Grey, Clare P.; Sideris, Paul J.

2008-01-01

The anion- exchange ability of layered double hydroxides ( LDHs) has been exploited to create materials for use in catalysis, drug delivery, and environmental remediation. The specific cation arrangements in the hydroxide layers of hydrotalcite- like LDHs, of general formula Mg1-x2+Alx3+OH2(Anion...

Analysis of Zr++++ dan ZrO++ cations through their Hydroxide precipitate with thermal differential analysis method

International Nuclear Information System (INIS)

Simbolon, Sahat; Ratmi-Herlani

1996-01-01

Hydroxide of zirconyl and zirconium, made by reacting zirconium and zirconyl solution with NH 4 OH 25 % solution, were analysed by thermal differential analysis (TDA). It was also done TDA method for hydroxide of zirconyl and zirconium, made by reacting zirconyl chloride and zirconium chloride solid with NH 4 OH 25 % solution directly. It was found that TDA of hydroxide precipitate made through solution had a clear TDA counter, meanwhile TDA thermogram of hydroxide precipitate made by direct adding NH 4 OH 25 % solution to zirconyl and zirconium hydroxide had no clear TDA thermogram. Precipitate Zr O(OH) 2 and Zr(OH) 4 found through solution could be differentiated each other based on their TDA thermograms

40 CFR 721.6183 - Amides, from ammonium hydroxide - maleic anhydride polymer and hydrogenated tallow alkyl amines...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Amides, from ammonium hydroxide... Substances § 721.6183 Amides, from ammonium hydroxide - maleic anhydride polymer and hydrogenated tallow... subject to reporting. (1) The chemical substance identified as amides, from ammonium hydroxide - maleic...

Inhibition effect of calcium hydroxide point and chlorhexidine point on root canal bacteria of necrosis teeth

Directory of Open Access Journals (Sweden)

Andry Leonard Je

2006-03-01

Full Text Available Calcium Hydroxide point and Chlorhexidine point are new drugs for eliminating bacteria in the root canal. The points slowly and controly realease Calcium Hydroxide and Chlorhexidine into root canal. The purpose of the study was to determined the effectivity of Calcium hydroxide point (Calcium hydroxide plus point and Chlorhexidine point in eleminating the root canal bacteria of nescrosis teeth. In this study 14 subjects were divided into 2 groups. The first group was treated with Calcium hydroxide point and the second was treated with Chlorhexidine poin. The bacteriological sampling were measured with spectrofotometry. The Paired T Test analysis (before and after showed significant difference between the first and second group. The Independent T Test which analysed the effectivity of both groups had not showed significant difference. Although there was no significant difference in statistical test, the result of second group eliminate more bacteria than the first group. The present finding indicated that the use of Chlorhexidine point was better than Calcium hydroxide point in seven days period. The conclusion is Chlorhexidine point and Calcium hydroxide point as root canal medicament effectively eliminate root canal bacteria of necrosis teeth.

Nickel hydroxide positive electrode for alkaline rechargeable battery

Science.gov (United States)

Young, Kwo; Wang, Lixin; Mays, William; Reichman, Benjamin; Chao-Ian, Hu; Wong, Diana; Nei, Jean

2018-02-20

Certain nickel hydroxide active cathode materials for use in alkaline rechargeable batteries are capable of transferring >1.3 electrons per Ni atom under reversible electrochemical conditions. The specific capacity of the nickel hydroxide active materials is for example .gtoreq.325 mAh/g. The cathode active materials exhibit an additional discharge plateau near 0.8 V vs. a metal hydride (MH) anode. Ni in an oxidation state of less than 2, such as Ni.sup.1+, is able to participate in electrochemical reactions when using the present cathode active materials. It is possible that up to 2.3 electrons, up to 2.5 electrons or more may be transferred per Ni atom under electrochemical conditions.

Nickel hydroxide positive electrode for alkaline rechargeable battery

Science.gov (United States)

Young, Kwo; Wang, Lixin; Mays, William; Reichman, Benjamin; Chao-Ian, Hu; Wong, Diana; Nei, Jean

2018-04-03

Certain nickel hydroxide active cathode materials for use in alkaline rechargeable batteries are capable of transferring >1.3 electrons per Ni atom under reversible electrochemical conditions. The specific capacity of the nickel hydroxide active materials is for example .gtoreq.325 mAh/g. The cathode active materials exhibit an additional discharge plateau near 0.8 V vs. a metal hydride (MH) anode. Ni in an oxidation state of less than 2, such as Ni.sup.1+, is able to participate in electrochemical reactions when using the present cathode active materials. It is possible that up to 2.3 electrons, up to 2.5 electrons or more may be transferred per Ni atom under electrochemical conditions.

Detonation nanodiamond introduced into samarium doped ceria electrolyte improving performance of solid oxide fuel cell

Science.gov (United States)

Pei, Kai; Li, Hongdong; Zou, Guangtian; Yu, Richeng; Zhao, Haofei; Shen, Xi; Wang, Liying; Song, Yanpeng; Qiu, Dongchao

2017-02-01

A novel electrolyte materials of introducing detonation nanodiamond (DNDs) into samarium doped ceria (SDC) is reported here. 1%wt. DNDs doping SDC (named SDC/ND) can enlarge the electrotyle grain size and change the valence of partial ceria. DNDs provide the widen channel to accelerate the mobility of oxygen ions in electrolyte. Larger grain size means that oxygen ions move easier in electrolyte, it can also reduce the alternating current (AC) impedance spectra of internal grains. The lower valence of partial Ce provides more oxygen vacancies to enhance mobility rate of oxygen ions. Hence all of them enhance the transportation of oxygen ions in SDC/ND electrolyte and the OCV. Ultimately the power density of SOFC can reach 762 mw cm-2 at 800 °C (twice higher than pure SDC, which is 319 mw cm-2 at 800 °C), and it remains high power density in the intermediate temperature (600-800 °C). It is relatively high for the electrolyte supported (300 μm) cells.

Use of dispersive liquid-liquid microextraction for simultaneous preconcentration of samarium, europium, gadolinium and dysprosium

International Nuclear Information System (INIS)

Mallah, M.H.; Atomic Energy Organization of Iran, Tehran; Shemirani, F.; Ghannadi Maragheh, M.

2008-01-01

A new preconcentration method of dispersive liquid-liquid microextraction (DLLME) was developed for simultaneous preconcentration of samarium, europium, gadolinium and dysprosium. DLLME technique was successfully used as a sample preparation method. In this preconcentration method, an appropriate mixture of extraction solvent, disperser solvent was injected rapidly into an aqueous solution containing Sm, Eu, Gd and Dy after complex formation using chelating reagent of the 1-(2-pyridylazo)-2-naphthol (PAN). After phase separation, 0.5 mL of the settled phase containing enriched analytes was determined by inductively coupled plasma optical emission spectrometry (ICP-OES). The main factors affected the preconcentration of Sm, Eu, Gd and Dy were extraction and dispersive solvent type and their volume, extraction time, volume of chelating agent (PAN), centrifuge speed and drying temperature of the samples. Under the best operating condition simultaneous preconcentration factors of 80, 100, 103 and 78 were obtained for Sm, Eu, Gd and Dy, respectively. (author)

Neutron activation analysis of the rare earth elements in Nasu hot springs

International Nuclear Information System (INIS)

Ikeda, Nagao; Takahashi, Naruto.

1978-01-01

Eleven rare earth elements (lanthanum, cerium, neodymium, samarium, europium, gadolinium, terbium, holmium, thulium, ytterbium and lutetium) in hot spring waters and sinter deposits in the Nasu area were determined by the neutron activation method. The rare earth elements in hot spring water were preconcentrated in ferric hydroxide precipitate and neutron-irradiated. The rare earth elements were chemically separated into lighter and heavier groups and the activity of each group was measured with a Ge(Li) detector. Distribution of the rare earth elements between the hot spring water and the sinter deposit was also discussed. (auth.)

Comparative evaluation of different forms of calcium hydroxide in apexification

OpenAIRE

Subhankar Ghosh; Dibyendu Mazumdar; Pradip Kumar Ray; Bhaswar Bhattacharya

2014-01-01

Background: One out of every two children sustains a dental injury most often between 8 and 10 years of age. Majority of these teeth subsequently become non-vital and most often with immature apex. Management of these teeth is an enormous challenge for lack of apical stop. Calcium hydroxide in various formulations has maximum literature support in favor of "successful apexification or induced apical closure." Aim: The aim of the following study is to determine the efficacy of calcium hydroxid...

Thermal analysis of iron hydroxide microspheres

International Nuclear Information System (INIS)

Turcanu, C.N.; Cornescu, M.

1979-03-01

The thermal treatment is an important step in the preparative technology of the iron oxids microspheres with well established mechanical, physical and chemical characteristics. The first indications on the heating procedure have been obtained from the thermal analysis on iron hydroxide microspheres prepared by the support precipitation and internal gelification methods. (author)

Clinical effect of calcium hydroxide paste combined with triple antibiotic paste on root canal disinfection

Directory of Open Access Journals (Sweden)

Chen QU

2014-03-01

Full Text Available Objective　To compare the efficacy in disinfection and pain control of calcium hydroxide paste and triple antibiotic paste (ornidazole, ciprofloxacin and minocycline used individually or jointly for root canal disinfection. Methods　Two hundred and thirty-five patients with chronic apical periodontitis (235 teeth were involved in the present study and divided into 2 groups: fistula group (n=118 and no fistula group (n=117. Each group was then randomly divided into 4 subgroups: calcium hydroxide paste group, triple antibiotic paste group, calcium hydroxide + triple antibiotic paste group, and camphor phenol group. After regular root canal preparation, root canals of patients in 4 groups were filled with tiny paper ends impregnated with fore 4 different drugs respectively. Visual analogue scales (VAS of pain were given to the patients with a guide for filling the scale. One week later, both the data of the scales and the effects of root canal disinfection were recorded and analyzed. Results　Seven days after treatment, the clinical efficacy of calcium hydroxide paste, triple antibiotic paste and calcium hydroxide + triple antibiotic paste was similar (P>0.05 either in fistula group or in no fistula group, but all better than that of camphor phenol (P<0.05. VAS score analysis showed that, at least on the first 3 days after sealing medicine in the root canal, calcium hydroxide + triple antibiotic paste achieved better result of pain control than the other three groups (P<0.05 no matter with or without fistula. Conclusions 　Calcium hydroxide paste, triple antibiotic paste, calcium hydroxide + triple antibiotic paste are effective in treatment of chronic apical periodontitis whether with or without fistula. However, the combined use of calcium hydroxide and three antibiotic pastes is better for controlling the pain after root canal preparation than other treatments, which is therefore worthy of clinical application. DOI: 10.11855/j.issn.0577-7402.2014.02.12

Characterization of luminescent samarium doped HfO2 coatings synthesized by spray pyrolysis technique

International Nuclear Information System (INIS)

Chacon-Roa, C; Guzman-Mendoza, J; Aguilar-Frutis, M; Garcia-Hipolito, M; Alvarez-Fragoso, O; Falcony, C

2008-01-01

Trivalent samarium (Sm 3+ ) doped hafnium oxide (HfO 2 ) films were deposited using the spray pyrolysis deposition technique. The films were deposited on Corning glass substrates at temperatures ranging from 300 to 550 deg. C using chlorides as raw materials. Films, mostly amorphous, were obtained when deposition temperatures were below 350 deg. C. However, for temperatures higher than 400 deg. C, the films became polycrystalline, presenting the HfO 2 monoclinic phase. Scanning electron microscopy of the films revealed a rough surface morphology with spherical particles. Also, electron energy dispersive analysis was performed on these films. The photoluminescence and cathodoluminescence characteristics of the HfO 2 : SmCl 3 films, measured at room temperature, exhibited four main bands centred at 570, 610, 652 and 716 nm, which are due to the well-known intra-4f transitions of the Sm 3+ ion. It was found that the overall emission intensity rose as the deposition temperature was increased. Furthermore, a concentration quenching of the luminescence intensity was also observed

Thermodynamic properties of beryllium hydroxide

International Nuclear Information System (INIS)

Baur, A.; Lecocq, A.

1964-01-01

The study of the hydro-thermal decomposition of beryllium hydroxide has made it possible to determine the free energy of formation and the entropy. The results obtained are in good agreement with the theoretical values calculated from the solubility product of this substance. They give furthermore the possibility of acquiring a better understanding of the BeO-H 2 O-Be (OH) 2 system between 20 and 1500 C. (authors) [fr

Infrared spectra of phosphate sorbed on iron hydroxide gel and the sorption products

International Nuclear Information System (INIS)

Nanzyo, M.

1986-01-01

Infrared absorption spectra of phosphate sorbed on iron hydroxide gel were obtained by applying the differential diffuse reflectance method. Absorption bands due to P-O stretching vibration were observed at 1,110 and 1,010 cm -1 at pH 12.3. With decreasing pH, these absorption bands gradually shifted to 1,100 and 1,020 cm -1 at pH 4.9. At pH 2.3, they became a broad single absorption band at 1,060 cm -1 . At pH 11 or above, the difference in the Na + adsorption between phosphated iron hydroxide gel and iron hydroxide gel was almost equal to the amount of phosphate sorption. This finding shows that phosphate was retained on the iron hydroxide gel surface as a bidentate ligand at a high pH. It was concluded that at a high pH phosphate was sorbed on iron hydroxide gel as a binuclear surface complex similar to that on goethite; the change in spectra for P-O stretching vibration with decreasing pH value was mainly caused by an increase in the fraction of amorphous iron phosphate; at pH 2.3, the phosphate sorption product consisted of amorphous iron phosphate. (author)

Structure of bayerite-based lithium-aluminum layered double hydroxides (LDHs): observation of monoclinic symmetry.

Science.gov (United States)

Britto, Sylvia; Kamath, P Vishnu

2009-12-21

The double hydroxides of Li with Al, obtained by the imbibition of Li salts into bayerite and gibbsite-Al(OH)(3), are not different polytypes of the same symmetry but actually crystallize in two different symmetries. The bayerite-derived double hydroxides crystallize with monoclinic symmetry, while the gibbsite-derived hydroxides crystallize with hexagonal symmetry. Successive metal hydroxide layers in the bayerite-derived LDHs are translated by the vector ( approximately -1/3, 0, 1) with respect to each other. The exigency of hydrogen bonding drives the intercalated Cl(-) ion to a site with 2-fold coordination, whereas the intercalated water occupies a site with 6-fold coordination having a pseudotrigonal prismatic symmetry. The nonideal nature of the interlayer sites has implications for the observed selectivity of Li-Al LDHs toward anions of different symmetries.

Sterically screened halogenocyclobutanones. I. Transformations of cyclopropyl-substituted 2,2-dichlorocyclobutanones under the influence of potassium hydroxide

International Nuclear Information System (INIS)

Donskaya, N.A.; Bessmertnykh, A.G.; Drobysh, V.A.; Shabarov, Yu.S.

1987-01-01

The reaction of 2,2-dichloro-3-cyclopropylcyclobutanones with potassium hydroxide was studied. The direction of the reaction depends on the concentration of the potassium hydroxide; with a 2% solution of potassium hydroxide 4,4-dichlorobutyric acids are formed with yields of up to 80%, and with a 15% solution of potassium hydroxide 5-hydroxydihydro-2-furanones are formed with yields of up to 80%. Proposals are made about the mechanism of formation of 5-hydroxydihydro-2-furanones

The theoretical basis and clinical methodology for stereotactic interstitial brain tumor irradiation using iododeoxyuridine as a radiation sensitizer and samarium-145 as a brachytherapy source

International Nuclear Information System (INIS)

Goodman, J.H.; Gahbauer, R.A.; Kanellitsas, C.; Clendenon, N.R.; Laster, B.H.; Fairchild, R.G.

1989-01-01

High grade astrocytomas have proven resistant to all conventional therapy. A technique to produce radiation enhancement during interstitial brain tumor irradiation by using a radiation sensitizer (IdUrd) and by stimulation of Auger electron cascades through absorption of low energy photons in iodine (Photon activation) is described. Clinical studies using IdUrd, 192 Ir as a brachytherapy source, and external radiation have produced promising results. Substituting samarium-145 for 192 Ir in this protocol is expected to produce enhanced results. 15 refs

Enhancement of the fluorescence of the samarium (III) complex by gadolinium (III)

International Nuclear Information System (INIS)

Yun-Xiang, C.; Zhang-Hua, L.

1988-01-01

The increase in sensitivity and selectivity of reactions in which colored species are formed by the addition of different metal ions is an area of research that has recently been developed. This phenomenon, which is sometimes called cocolaration effect, has been explained by the formation of mixed metal complex. The authors found an analogous phenomenon of reactions forming fluorescent complexes. The complexes of Sm(III)-thenoyltrifluoroacetone (TTA)-phenanthroline (Phen)-Triton-X-100 (TX-100) and Gd(III) (or La(III), Lu(III) and Y(III))-TTA-Phen-TX-100 had practically no fluorescence separately. Instead, a fluorescence-enhancement phenomenon caused by adding Gd or La, Lu and Y ions to the system was observed for the first time. The intensity of the enhanced fluorescence of Sm(III) complex was increased in the following order: La< Y< Lu< Gd. By analogy with cocoloration effect, the authors call this new fluorescence-enhancement phenomenon the co-fluorescence effect. The object of this work was to study the enhancement effect of Gd(III) on the fluorescence of the Sm(III)-TTA-Phen-TX-100 system. The recommended fluorimetric method has been applied to the determination of trace amounts of samarium in ytterbium oxide with satisfactory results. A general reaction mechanism for the system studied was proposed

Clinical Survey of Successfulness of DPC with MTA and Calcium Hydroxide

Directory of Open Access Journals (Sweden)

E.Yasini

2005-02-01

Full Text Available Statement of Problem: The pulp may be exposed during remove of caries or by traumatic and iatrogenicinjuries. The material used to DPC, must be biocompatible, scalable and prevent bacterial leakage.Furthermore, it is better to stimulate dentinogenesis. Calcium hydroxide is most usual material for DPC. But itcannot provide a suitablcbiologic seal. Mineral irioxide aggregate (MTA is also a suitable material for DPC.Purpose: The aim of this study was to compare the clinical success of DPC done with MTA or calciumhydroxide cement.Materials and Methods: In this study eighteen posterior teeth without previous spontaneous pain thatinvolved mechanicaly exposure was randomly selected and capped with MTA or calcium hydroxide. These teeth were evaluated by clinical vitality test and radiograph after 3 and 12 months, and patients werequestioned about irritative or spontancus pain in this period. Statistical analysis was carried out by Usher exacttest (a-0.05.Results: This study showed that in calcium hydroxid groud three had irreversible pulpitis and two teeth had symptom and signs of reversible pulpitis. While, In MTA group all cases were normaL and no clinical sign was evident.Conclusion: MTA exhibited better results than calcium hydroxide cement for the capping of the pulp in human

Polytypic transformations during the thermal decomposition of cobalt hydroxide and cobalt hydroxynitrate

International Nuclear Information System (INIS)

Ramesh, Thimmasandra Narayan

2010-01-01

The isothermal decomposition of cobalt hydroxide and cobalt hydroxynitrate at different intervals of temperature leads to the formation of Co 3 O 4 . The phase evolution during the decomposition process was monitored using powder X-ray diffraction. The transformation of cobalt hydroxide to cobalt oxide occurs via three phase mixture while cobalt hydroxynitrate to cobalt oxide occurs through a two phase mixture. The nature of the sample and its preparation method controls the decomposition mechanism. The comparison of topotactical relationship between the precursors to the decomposed product has been reported in relation to polytypism. - Graphical abstract: Isothermal thermal decomposition studies of cobalt hydroxide and cobalt hydroxynitrate at different intervals of temperature show the metastable phase formed prior to Co 3 O 4 phase.

Automated solid-phase extraction of phenolic acids using layered double hydroxide-alumina-polymer disks.

Science.gov (United States)

Ghani, Milad; Palomino Cabello, Carlos; Saraji, Mohammad; Manuel Estela, Jose; Cerdà, Víctor; Turnes Palomino, Gemma; Maya, Fernando

2018-01-26

The application of layered double hydroxide-Al 2 O 3 -polymer mixed-matrix disks for solid-phase extraction is reported for the first time. Al 2 O 3 is embedded in a polymer matrix followed by an in situ metal-exchange process to obtain a layered double hydroxide-Al 2 O 3 -polymer mixed-matrix disk with excellent flow-through properties. The extraction performance of the prepared disks is evaluated as a proof of concept for the automated extraction using sequential injection analysis of organic acids (p-hydroxybenzoic acid, 3,4-dihydroxybenzoic acid, gallic acid) following an anion-exchange mechanism. After the solid-phase extraction, phenolic acids were quantified by reversed-phase high-performance liquid chromatography with diode-array detection using a core-shell silica-C18 stationary phase and isocratic elution (acetonitrile/0.5% acetic acid in pure water, 5:95, v/v). High sensitivity and reproducibility were obtained with limits of detection in the range of 0.12-0.25 μg/L (sample volume, 4 mL), and relative standard deviations between 2.9 and 3.4% (10 μg/L, n = 6). Enrichment factors of 34-39 were obtained. Layered double hydroxide-Al 2 O 3 -polymer mixed-matrix disks had an average lifetime of 50 extractions. Analyte recoveries ranged from 93 to 96% for grape juice and nonalcoholic beer samples. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Growth of uranyl hydroxide nanowires and nanotubes with electrodeposition method

International Nuclear Information System (INIS)

Wang Lin; Yuan Liyong; Chai Zhifang; Shi Weiqun

2013-01-01

Actinides nanomaterials have great potential applications in fabrication of novel nuclear fuel and spent fuel reprocessing in advanced nuclear energy system. However, the relative research so far still lacks systematic investigation on the synthetic methods for actinides nanomaterials. In this work, we use track-etched membranes as hard templates to synthesize uranium based nanomaterials with novel structures by electrodeposition method. Through electrochemical behavior investigations and subsequent product characterizations such as energy dispersive spectrometer (EDS), fourier transform infrared spectroscopy (FTIR), the chemical composition of deposition products have been confirmed as the uranyl hydroxide. More importantly, accurate control of morphology and structures (nanowires and nanotubes) could be achieved by carefully adjusting the growth parameters such as deposition time and deposition current density. It was found that the preferred morphology of electrodeposition products is nanowire when a low current density was applied, whereas nanotubes could be formed only under conditions of high current density and the short deposition time. The mechanism for the formation of nanowires in track-etched membranes is based on the precipitation of uranyl hydroxide from uranyl nitrate solution, according to the previous researches about obtaining nanostructures of hydroxides from nitrate salt solutions. And we have concluded that the formation of nanotubes is attributed to the hydrogen bubbles generated by water electrolysis under the condition of over-potential electro-reduction. The conveying of hydrogen bubbles plays the role of dynamic template which can prevent the complete filling of uranyl hydroxide in the channels. Additionally, we transform the chemical composition of deposition products from uranyl hydroxide to triuranium octoxide by calcining them at 500 and 800 degree centigrade, respectively, and SEM results show the morphologies of nanowires and

The Effects of Aluminium Hydroxide and Magnesium Hydroxide on the Mechanical Properties of Thermoplastic Polyurethane Materials

Directory of Open Access Journals (Sweden)

Erkin Akdoğan

2015-12-01

Full Text Available Thermoplastic polyurethane materials are widely used in automotive, clothing, electrical and electronics, medical, construction, machine industry due to excellent physical and chemical properties. Thermoplastic polyurethane materials combustion and resistance to high temperature characteristics are poor. Additives and fillers are added into the polyurethane matrix to improve those properties. Particularly adding these agents as a flame retardant are affect mechanical properties of polyurethane materials. Therefore, it is important to determinate the mechanical properties of these materials. In this study, 5% by weight of the thermoplastic polyurethane material, aluminium tri hydroxide (ATH, (Al2O3 3H2O and magnesium hydroxide (MgOH, (Mg(OH2 were added. Ammonium polyphosphate (APP as an intumescent flame retardant with inorganic flame retardants were added to increase the flame resistance of produced composite structure. Tensile test, tear test, hardness and Izod impact tests were made and compared of those produced composites. As a result of experiments the addition of ATH has lowered the tensile strength and tear strength contrast to this the addition of MgOH has improved those properties. Hardness and Izod impact test results were showed that both of the additives have no negative effect.

Electrodeposition of Zn-doped {alpha}-nickel hydroxide with flower-like nanostructure for supercapacitors

Energy Technology Data Exchange (ETDEWEB)

You Zheng [Department of Precision Instruments and Mechanology, Tsinghua University, Beijing 100084 (China); Shen Kui; Wu Zhicheng [Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China); Wang Xiaofeng [Department of Precision Instruments and Mechanology, Tsinghua University, Beijing 100084 (China); Kong Xianghua, E-mail: kongxh@ustb.edu.cn [Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China)

2012-08-01

Zn-doped {alpha}-nickel hydroxide materials with flower-like nanostructures are synthesized by electrochemical deposition method. The samples are characterized by X-ray diffraction (XRD), field emission scanning electron microscope (SEM) and electrochemical measurements. XRD spectra indicate nickel hydroxide doped with Zn is {alpha}-Ni(OH){sub 2} with excellent crystallization. The SEM observation shows that the formation of Zn-doped Ni(OH){sub 2} includes two steps: a honeycomb-like film forms on the substrate first, then flower-like particles forms on the films. The nickel hydroxide doped with 5% Zn can maintain a maximum specific capacitance of 860 F g{sup -1}, suggesting its potential application in electrochemical capacitors.

Electrodeposition of Zn-doped α-nickel hydroxide with flower-like nanostructure for supercapacitors

Science.gov (United States)

You, Zheng; Shen, Kui; Wu, Zhicheng; Wang, Xiaofeng; Kong, Xianghua

2012-08-01

Zn-doped α-nickel hydroxide materials with flower-like nanostructures are synthesized by electrochemical deposition method. The samples are characterized by X-ray diffraction (XRD), field emission scanning electron microscope (SEM) and electrochemical measurements. XRD spectra indicate nickel hydroxide doped with Zn is α-Ni(OH)2 with excellent crystallization. The SEM observation shows that the formation of Zn-doped Ni(OH)2 includes two steps: a honeycomb-like film forms on the substrate first, then flower-like particles forms on the films. The nickel hydroxide doped with 5% Zn can maintain a maximum specific capacitance of 860 F g-1, suggesting its potential application in electrochemical capacitors.

Honeywell Modular Automation System Computer Software Documentation for the Magnesium Hydroxide Precipitation Process

International Nuclear Information System (INIS)

STUBBS, A.M.

2001-01-01

The purpose of this Computer Software Document (CSWD) is to provide configuration control of the Honeywell Modular Automation System (MAS) in use at the Plutonium Finishing Plant (PFP) for the Magnesium Hydroxide Precipitation Process in Rm 230C/234-5Z. The magnesium hydroxide process control software Rev 0 is being updated to include control programming for a second hot plate. The process control programming was performed by the system administrator. Software testing for the additional hot plate was performed per PFP Job Control Work Package 2Z-00-1703. The software testing was verified by Quality Control to comply with OSD-Z-184-00044, Magnesium Hydroxide Precipitation Process

Growth kinetics for the precipitation of zirconium hydroxide from aqueous zirconium and tin bearing solutions by the addition of ammonium hydroxide

Energy Technology Data Exchange (ETDEWEB)

Carleson, T.E. [Idaho Univ., Moscow, ID (United States). Dept. of Chemical Engineering; Chipman, N.A. [Westinghouse Idaho Nuclear Co., Inc., Idaho Falls, ID (United States)

1989-09-11

The precipitation of zirconium hydroxide from an aqueous solution of ammonium hexafluorozirconate occurs rapidly upon addition of ammonium hydroxide. Experimental data indicate growth and nucleation rates between 0.06 and 0.28 microns/minute and around 10 {times} 107 number/L-min, respectively. Experiments with a mixed suspension mixed product removal crystallizer for concentrations of reactants of about 0.05 M ammonium hexafluorozirconate precipitating with 0.002 M ammonium hydroxide showed apparent nonlinear growth rates in some cases but not others. Batch studies indicated that growth rate dispersion is probably not present. When the AFL nonlinear model was used to fit the data, the power coefficient obtained was greater than 1, in disagreement with theory. In addition, for some of the data ``S`` shaped curves of the logarithm of the cumulative number greater than versus size were obtained. These curves can not be fit by the AFL model. A program developed at the University of Arizona was used to simulate the crystallization runs. The program results indicated that some of the nonlinear behavior may be attributed to transient conditions. Experimental data also illustrated this behavior. The effect of trace amounts of tin fluoride (0.008 M) on the nucleation and growth kinetics was also evaluated. For some residence times, the presence of tin resulted in reduced median particle diameters, higher growth rates, and lower number counts.

Structural Differentiation between Layered Single (Ni) and Double Metal Hydroxides (Ni–Al LDHs) Using Wavelet Transformation

Energy Technology Data Exchange (ETDEWEB)

Siebecker, Matthew G. [University of Delaware, Delaware Environmental Institute; Sparks, Donald L. [University of Delaware, Delaware Environmental Institute

2017-09-07

Layered double hydroxides (LDHs) are anionic clays important in disciplines such as environmental chemistry, geochemistry, and materials science. Developments in signal processing of extended X-ray absorption fine structure (EXAFS) data, such as wavelet transformation (WT), have been used to identify transition metals and Al present in the hydroxide sheets of LDHs. The WT plots of LDHs should be distinct from those of isostructural single metal hydroxides. However, no direct comparison of these minerals appears in the literature using WT. This work systematically analyzes a suite of Ni-rich mineral standards, including Ni–Al LDHs, single metal Ni hydroxides, and Ni-rich silicates using WT. The results illustrate that the WT plots for α-Ni(OH)2 and Ni–Al LDHs are often indistinguishable from each other, with similar two-component plots for the different mineral types. This demonstrates that the WT of the first metal shell often cannot be used to differentiate an LDH from a single metal hydroxide. Interlayer anions adsorbed to the hydroxide sheet of α-Ni(OH)2 affect the EXAFS spectra and are not visible in the FT but are clearly resolved and discrete in the WT.

Strong blue emission from zinc hydroxide carbonate nanosheets

International Nuclear Information System (INIS)

Mao, Jing; Chen, Xuemin; Ling, Tao; Du, Xiwen

2016-01-01

Zinc hydroxide carbonate (ZHC) is a typical layered salt composed of zinc hydroxide layers separated with carbonate ions and water molecules. Studies of morphology control and the constitution of functional ZHC material with intercalated ions has been widely developed. Also, ZnO can be easily obtained by anneal treatment of ZHC, and the porous structure as synthesized had great potential in gas sensors, photocatalysts and dye-sensitized solar cells. However, the optical of ZHC have rarely been investigated. In our research, a strong blue emission of ZHC is reported. The effect of growth time, annealing treatment and modification of surfactants on blue emission have been systematically studied. Combined with information of interior effect of OH groups, crystal structure and electronegativity of surfactants, a possible emission mechanism of ZHC has been proposed.

Hydroxide Self-Feeding High-Temperature Alkaline Direct Formate Fuel Cells.

Science.gov (United States)

Li, Yinshi; Sun, Xianda; Feng, Ying

2017-05-22

Conventionally, both the thermal degradation of the anion-exchange membrane and the requirement of additional hydroxide for fuel oxidation reaction hinder the development of the high-temperature alkaline direct liquid fuel cells. The present work addresses these two issues by reporting a polybenzimidazole-membrane-based direct formate fuel cell (DFFC). Theoretically, the cell voltage of the high-temperature alkaline DFFC can be as high as 1.45 V at 90 °C. It has been demonstrated that a proof-of-concept alkaline DFFC without adding additional hydroxide yields a peak power density of 20.9 mW cm -2 , an order of magnitude higher than both alkaline direct ethanol fuel cells and alkaline direct methanol fuel cells, mainly because the hydrolysis of formate provides enough OH - ions for formate oxidation reaction. It was also found that this hydroxide self-feeding high-temperature alkaline DFFC shows a stable 100 min constant-current discharge at 90 °C, proving the conceptual feasibility. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Determination of Aluminium Content in Aluminium Hydroxide Formulation by FT-NIR Transmittance Spectroscopy

DEFF Research Database (Denmark)

Lai, Xuxin; Zheng, Yiwu; Søndergaard, Ib

2007-01-01

A method for determining the aluminium content of an aluminium hydroxide suspension using near infrared (NIR) transmittance spectroscopy has been developed. Inductively coupled plasma-atomic emission spectroscopy (ICP-AES) was used as reference method. The factors influencing the NIR analysis...... aluminium content in aluminium hydroxide suspension. (c) 2007 Elsevier Ltd. All rights reserved....

Technical basis for a minimum hydroxide concentration in tanks containing dilute waste

International Nuclear Information System (INIS)

Zapp, P.E.

1995-05-01

Laboratory tests were performed to address the protection of waste tank steel from corrosion in situations of elevated temperatures up to 75 C (hot spots) in the sludge layer of Extended Sludge Processing (ESP) tanks. Coupon immersion tests were conducted at 75 C in two ESP simulants at four hydroxide (or pH) levels. The nitrite concentrations of the simulants were calculated from the ESP technical standards based on a temperature of 40 C. The results showed that a hydroxide concentration of at least 0.01 M prevented significant corrosion of the steel at the elevated temperature. This conclusion provides the technical basis for the revised minimum hydroxide concentration of 0.01 M in the draft WSRC 241-82H Control Room Process Requirements, for the ESP tanks

Results after therapy of pain from bone metastases with Samarium-153 in our centers in Lima, Peru

International Nuclear Information System (INIS)

Alvarado, N.; Eskenazi, S.; Valle, M.P.; Montoya, J.; Castro, M.; Montiel, L.; Velarde, V.; Jauregui, I.; Cueto, C.

2004-01-01

Full text: 105 patients with bone metastases from prostate and breast cancer; between 42 and 78 years age (median 61 years) were evaluated. Patients had intense pain that could not be managed with combinations of analgesic and anti tumoral drugs. All patients received 1.2 mCi/kg of Samarium-153 intravenously as treatment for pain due to bony metastases. The isotope obtained from atomic reactor placed in Lima - Peru, was provided by Peruvian Nuclear Energy Institute (IPEN). One week before therapy, all the patients had a bone scan study with Tc99m-MDP that showed the presence of multiple bone metastases with high blastic activity. Haematology and biochemical parameter checked were: Creatinine ( 150,000 mm3), Leukocytes (> 5,000 mm3), Red cells (>3,500,000 mm3). No problems were encountered during intravenous administration of the radioisotope. The side effects after treatment were: Primary effects: 16 cases of nausea, 2 of vomiting, 3 of headache, 28 had increment of pain, 6 had flushing. 50 patients did not have the primary symptoms. Secondary effects: 3 Patients showed drop in leukocyte count between 2nd and 3rd week of therapy. Red cells showed 10-15% decrease between 6th to 8th week. Platelets showed a decrease of about 15% with one peak between 1st and 2nd week post Samarium therapy. Data was analysed using an analogue visual scale of the pain with values from 0 - 10 (0-no pain; 10-maximum pain) and in the same way using the E.C.O.G. scale (Eastern Cooperative Oncology Group) in relationship with the Karnofsky index in order to establish functional recovery for each patient. The decrease of pain was seen between 4th-7th days (average 8 days). A second dose was given after 60 days in 12 patients and a third dose in 3 cases.11 patients died due to different causes between 30 - 60 days post treatment. The analgesic dose came down significantly in 80% of patients. We conclude that palliative therapy of metastatic bone pain in Peru is possible with radionuclides. It

Potassium hydroxide 5% for the treatment of molluscum contagiosum.

Science.gov (United States)

2014-10-01

Molluscum contagiosum is a common reason for consultation in primary care. The condition is normally benign and self-limiting1 and the standard advice is to wait for the lesions to resolve spontaneously.2 Recently, potassium hydroxide 5% (MolluDab-Alliance Pharmaceuticals Limited) has been marketed in the UK for the treatment of the condition.3 It is sold as a medical device rather than a licensed medicinal product. Here we consider the evidence for potassium hydroxide 5% in the management of molluscum contagiosum. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Effects of adhesions of amorphous Fe and Al hydroxides on surface charge and adsorption of K+ and Cd2+ on rice roots.

Science.gov (United States)

Liu, Zhao-Dong; Wang, Hai-Cui; Zhou, Qin; Xu, Ren-Kou

2017-11-01

Iron (Fe) and aluminum (Al) hydroxides in variable charge soils attached to rice roots may affect surface-charge properties and subsequently the adsorption and uptake of nutrients and toxic metals by the roots. Adhesion of amorphous Fe and Al hydroxides onto rice roots and their effects on zeta potential of roots and adsorption of potassium (K + ) and cadmium (Cd 2+ ) by roots were investigated. Rice roots adsorbed more Al hydroxide than Fe hydroxide because of the greater positive charge on Al hydroxide. Adhesion of Fe and Al hydroxides decreased the negative charge on rice roots, and a greater effect of the Al hydroxide. Consequently, adhesion of Fe and Al hydroxides reduced the K + and Cd 2+ adsorption by rice roots. The results of attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR) and desorption of K + and Cd 2+ from rice roots indicated that physical masking by Fe and Al hydroxides and diffuse-layer overlapping between the positively-charged hydroxides and negatively-charged roots were responsible for the reduction of negative charge on roots induced by adhesion of the hydroxides. Therefore, the interaction between Fe and Al hydroxides and rice roots reduced negative charge on roots and thus inhibited their adsorption of nutrient and toxic cations. Copyright © 2017 Elsevier Inc. All rights reserved.

In vitro antibacterial effect of calcium hydroxide combined with chlorhexidine or iodine potassium iodide on Enterococcus faecalis.

Science.gov (United States)

Sirén, Eva K; Haapasalo, Markus P P; Waltimo, Tuomas M T; Ørstavik, Dag

2004-08-01

Several studies have shown a higher success rate of root canal therapy when the canal is free from bacteria at the time of obturation. Treatment strategies that are designed to eliminate this microflora should include agents that can effectively disinfect the root canal. Enterococcus faecalis is often associated with persistent endodontic infections. While in vivo studies have indicated calcium hydroxide to be the most effective all-purpose intracanal medicament, iodine potassium iodide (IKI) and chlorhexidine (CHX) may be able to kill calcium hydroxide-resistant bacteria. Supplementing the antibacterial activity of calcium hydroxide with IPI or CHX preparations was studied in bovine dentine blocks. While calcium hydroxide was unable to kill E. faecalis in the dentine, calcium hydroxide combined with IKI or CHX effectively disinfected the dentine. The addition of CHX or IKI did not affect the alkalinity of the calcium hydroxide suspensions. It may be assumed that combinations also have the potential to be used as long-term medication. Cytotoxicity tests using the neutral red method indicated that the combinations were no more toxic than their pure components.

Synthesis and characterization of laurate-intercalated Mg–Al layered double hydroxide prepared by coprecipitation

DEFF Research Database (Denmark)

Gerds, Nathalie Christiane; Katiyar, Vimal; Koch, Christian Bender

2012-01-01

Effective utilization of layered double hydroxides (LDH) for industrial applications requires the synthesis of pure and well-defined LDH phases. In the present study, dodecanoate (laurate) anions were intercalated into Mg–Al-layered double hydroxide (LDH-C12) by coprecipitation in the presence of...

Accidental periapical extrusion of non-setting calcium hydroxide: Unusual bone response and management

Directory of Open Access Journals (Sweden)

Divya S Sharma

2014-01-01

Full Text Available Premixed non-setting calcium hydroxide is frequently used as interim root canal dressing in endodontically involved permanent teeth and as obturating paste in deciduous teeth in pediatric dentistry. Wide apex in both cases makes it more prone for deliberate extrusion especially when applied with pressure delivery systems. Contrary to common belief the mix was not resorbed in two years with the complaint of insufficiency in mastication. Large mass of calcium hydroxide in bone delayed healing process even after its removal. The present case report intends to demonstrate unusual behavior of bone in response to oily non-setting preparation of calcium hydroxide. Therefore its application with pressure syringe should be reconsidered in pediatric dentistry.

Separation of valence forms of chromium(III) and chromium(VI) by coprecipitation with iron(III) hydroxide

International Nuclear Information System (INIS)

Nazirmadov, B.; Khamidov, B.O.; Egorova, L.A.

1989-01-01

The sorption of 9.62·10 -5 M of Cr (III) and Cr (VI) with iron hydroxide in 1 M potassium nitrate and potassium chloride was investigated in relation to the pH of the medium. Experimental data on the sorption of chromium(III) and chromium(VI) with iron(III) hydroxide made it possible to determine the region of practically complete concentration of Cr (III) and Cr (VI) (pH = 3-6.5). The results from spectrophotometric investigations, calculated data on the distribution of the hydroxocationic forms of chromium(III) and the anions of chromium(IV), and their sorption by iron-(III) hydroxide made it possible to characterize the sorbability of the cationic and anionic forms of chromium in various degrees of oxidation. On this basis a method was developed for the separation of chromium(III) and chromium(VI) by coprecipitation on iron(III) hydroxide and their separation from the iron(III) hydroxide support

Utilization of Magnesium Hydroxide Produced by Magnesia Hydration as Fire Retardant for Nylon 6-6,6

Directory of Open Access Journals (Sweden)

Rocha Sônia D.F.

2001-01-01

Full Text Available The present work investigates the use of magnesium hydroxide, produced by magnesia hydration, as a fire retardant in polymers. The hydration was carried out in an autoclave, at temperature of 130°C for 1 hour, and the product was further submitted to cominution in a jet mill. The solids were characterized with regard to their chemical composition, particle size distribution, surface area and morphology. The performance evaluation of the hydroxide as a flame retardant for a copolymer of nylon 6-6,6 was carried out according to the UL94 specifications for vertical burning tests. V-0 flammability rating at 1.6 mm (60% magnesium hydroxide-filled nylon composite and at 3.2 mm (40% magnesium hydroxide filled nylon composite were achieved. Mechanical properties were maintained at the desired values. These results indicate that the hydroxide obtained from magnesia hydration can be successfully employed as a fire retardant for nylon 6-6,6.

Reactions between rocks and the hydroxides of calcium, sodium and potassium: progress report no. 1

International Nuclear Information System (INIS)

Van Aardt, J.H.P.; Visser, S.

1982-01-01

The reaction between the hydroxides of calcium, sodium and potassium, and clay minerals, feldspars, and some rocks (aggregates for use in concrete) was investigated. The reaction products were examined by means of x-ray diffraction and chemical analysis. The solid reaction products identified were hydrated calcium silicates,hydrated calcium aluminates, and hydrated calcium alumina silicates. It was found that, in the presence of water, calcium hydroxide liberated alkali into solution if the rocks and minerals contained alkali metals in their structure. Two crystalline hydrated sodium calcium silicates (12A and 16A) were prepared in the system Na 2 O-CaO-SiO 2 -H 2 O at 80 degrees Celsius. The one compound (12A) was also observed when sodium hydroxide plus calcium hydroxide and water reacted with silica- or silicate-containing rocks

On the effects of pressure and irradiation on the transport properties of samarium compounds with unstable valence

International Nuclear Information System (INIS)

Morillo, J.

1983-06-01

We present the first extensive study of electronic transport properties of ''quasi-stoichiometric'' SmS as a function of pressure P, temperature T, magnetic field B and defect concentration C. SmS which is a semiconductor, undergoes with increasing P a first order transition towards an homogeneous intermediate valence state. In the semiconducting phase (s.c.), the energie epsilon(f) necessary to delocalize a 4f electron increases greatly with T and is about 250meV at 300K. The phase diagram for the first order electronic transition Sm 2 + →Smsup(2+epsilon) with P has been determined for T 6 has been investigated by resistivity measurements under irradiation at 21K. The threshold energy Ed for displacement of Sm in SmS has been determined: Ed(Sm) = 20 +- 2 eV, and the observed effects of irradiation have been associated to samarium displacements (vacancies and interstitials) [fr

Effect of Zinc Oxide Doping on Electroluminescence and Electrical Behavior of Metalloporphyrins-Doped Samarium Complex

Science.gov (United States)

Janghouri, Mohammad; Amini, Mostafa M.

2018-02-01

Samarium complex [(Sm(III)] as a new host material was used for preparation of red organic light-emitting diodes (OLEDs). Devices with configurations of indium-doped tin oxide (ITO)/poly(3,4-ethylenedioxythiophene):(poly(styrenesulfonate) (PEDOT:PSS (50 nm)/polyvinyl carbazole (PVK):[zinc oxide (ZnO)] (50 nm)/[(Sm(III)]:[zinc(II) 2,3-tetrakis(dihydroxyphenyl)-porphyrin and Pt(II) 2,3-dimethoxyporphyrin] (60 nm)/2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) (15 nm)/Al (150 nm) have been fabricated and investigated. An electroplex occurring at the (PVK/Sm: Pt(II) 2,3-dimethoxyporphyrin) interface has been suggested when ZnO nanoparticles were doped in PVK. OLED studies have revealed that the photophysical characteristics and electrical behavior of devices with ZnO nanoparticles are much better than those of devices with pure PVK. The efficiency of devices based on [(Sm(III)] was superior than that of known aluminum tris(8-hydroxyquinoline) (Alq3) and also our earlier reports on red OLEDs under the same conditions.

Kinetics of sodium borohydride direct oxidation and oxygen reduction in sodium hydroxide electrolyte

International Nuclear Information System (INIS)

Chatenet, Marian; Micoud, Fabrice; Roche, Ivan; Chainet, Eric

2006-01-01

The direct oxidation of sodium borohydride in concentrated sodium hydroxide medium has been studied by cyclic and linear voltammetry, chronoamperometry and chronopotentiometry for silver and gold electrocatalysts, either bulk and polycrystalline or nanodispersed over high area carbon blacks. Gold and silver yield rather complete utilisation of the reducer: around 7.5 electrons are delivered on these materials, versus 4 at the most for platinum as a result of the BH 4 - non-negligible hydrolysis taking place on this latter material. The kinetic parameters for the direct borohydride oxidation are better for gold than for silver. A strong influence of the ratio of sodium hydroxide versus sodium borohydride is found: whereas the theoretical stoichiometry does forecast that eight hydroxide ions are needed for each borohydride ion, our experimental results prove that a larger excess hydroxide ion is necessary in quasi-steady state conditions. When the above-mentioned ratio is unity (1 M NaOH and 1 M NaBH 4 ), the tetrahydroborate ions direct oxidation is limited by the hydroxide concentration, and their hydrolysis is no longer negligible. The hydrolysis products are probably BH 3 OH - ions, for which gold displays a rather good oxidation activity. Additionally, silver, which is a weak BH 4 - oxidation electrocatalyst, exhibits the best activity of all the studied materials towards the BH 3 OH - direct oxidation. Finally, carbon-supported gold nanoparticles seem promising as anode material to be used in direct borohydride fuel cells

The Effect of Calcium Hydroxide As an Intracanal Medication of The Apical Microleakage

Directory of Open Access Journals (Sweden)

Heshmat Mohajer AR

2011-12-01

Full Text Available Background and Aims: Nowadays, calcium hydroxide is used as a dressing for canal sterilization and repair progression of apical lesions. The aim of this study was to investigate the effect of calcium hydroxide as an intracanal medicament on the apical microleakage of root filling.Materials and Methods: In this experimental study, 46 extracted single-rooted human teeth were instrumented with step-back technique to master apical file (MAF size 35. Specimens were randomly divided into 2 groups (n = 20. In group 1, the specimens were treated with calcium hydroxide intracanal medication; and in group 2, the samples did not receive any medication. The teeth were incubated in 100% humidity at 37°C for one week. After that, calcium hydroxide was removed using irrigation with normal saline and reaming with MAF. The root canals were obturated with gutta- percha and AH26 sealer using lateral compaction technique. Specimens were incubated in 100% humility at 37°C for 72 hours and then immersed in India ink for 1 week. Finally, the teeth were cleared and the maximum linear dye penetration was measured under a stereomicroscope at 4X magnification. The data were analyzed by T-test and Chi-square.Results: There was no significant difference between the two experimental groups (P=0.068. Conclusion: The findings of this study indicated that using calcium hydroxide as an intracanal medicament did not influence the apical microleakage after final obturation of the root canal system.

Solar Hydrogen Production via a Samarium Oxide-Based Thermochemical Water Splitting Cycle

Directory of Open Access Journals (Sweden)

Rahul Bhosale

2016-04-01

Full Text Available The computational thermodynamic analysis of a samarium oxide-based two-step solar thermochemical water splitting cycle is reported. The analysis is performed using HSC chemistry software and databases. The first (solar-based step drives the thermal reduction of Sm2O3 into Sm and O2. The second (non-solar step corresponds to the production of H2 via a water splitting reaction and the oxidation of Sm to Sm2O3. The equilibrium thermodynamic compositions related to the thermal reduction and water splitting steps are determined. The effect of oxygen partial pressure in the inert flushing gas on the thermal reduction temperature (TH is examined. An analysis based on the second law of thermodynamics is performed to determine the cycle efficiency (ηcycle and solar-to-fuel energy conversion efficiency (ηsolar−to−fuel attainable with and without heat recuperation. The results indicate that ηcycle and ηsolar−to−fuel both increase with decreasing TH, due to the reduction in oxygen partial pressure in the inert flushing gas. Furthermore, the recuperation of heat for the operation of the cycle significantly improves the solar reactor efficiency. For instance, in the case where TH = 2280 K, ηcycle = 24.4% and ηsolar−to−fuel = 29.5% (without heat recuperation, while ηcycle = 31.3% and ηsolar−to−fuel = 37.8% (with 40% heat recuperation.

Topotactic Consolidation of Monocrystalline CoZn Hydroxides for Advanced Oxygen Evolution Electrodes.

Science.gov (United States)

Wang, Jing; Tan, Chuan Fu; Zhu, Ting; Ho, Ghim Wei

2016-08-22

We present a room temperature topotactic consolidation of cobalt and zinc constituents into monocrystalline CoZn hydroxide nanosheets, by a localized corrosion of zinc foils with cobalt precursors. By virtue of similar lattice orientation and structure coordination, the hybrid hydroxides amalgamate atomically without phase separation. Importantly, this in situ growth strategy, in combination with configurable percolated nanosheets, renders a high areal density of catalytic sites, immobilized structures, and conductive pathways between the nanosheets and underlying foils-all of which allow monocrystalline CoZn hydroxide nanosheet materials to function as effective electrodes for electrochemical oxygen evolution reactions. This convenient and eco-friendly topotactical transformation approach facilitates high-quality single crystal growth with improved multiphase purity and homogeneity, which can be extended to other transition metals for the fabrication of advanced functional nanocomposites. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mixing Acid Salts and Layered Double Hydroxides in Nanoscale under Solid Condition

OpenAIRE

Nakayama, Hirokazu; Hayashi, Aki

2014-01-01

The immobilization of potassium sorbate, potassium aspartate and sorbic acid in layered double hydroxide under solid condition was examined. By simply mixing two solids, immobilization of sorbate and aspartate in the interlayer space of nitrate-type layered double hydroxide, so called intercalation reaction, was achieved, and the uptakes, that is, the amount of immobilized salts and the interlayer distances of intercalation compounds were almost the same as those obtained in aqueous solution...

Biodistribution of samarium-153-EDTMP in rats treated with docetaxel Biodistribuição de EDTMP-153-samário em ratos tratados com docetaxel

Directory of Open Access Journals (Sweden)

Arthur Villarim Neto

2009-02-01

Full Text Available PURPOSE: Many patients with metastatic bone disease have to use radiopharmaceuticals associated with chemotherapy to relieve bone pain. The aim of this study was to assess the influence of docetaxel on the biodistribution of samarium-153-EDTMP in bones and other organs of rats. METHODS: Wistar male rats were randomly allocated into 2 groups of 6 rats each. The DS (docetaxel/samarium group received docetaxel (15 mg/kg intraperitoneally in two cycles 11 days apart. The S (samarium/control group rats were not treated with docetaxel. Nine days after chemotherapy, all the rats were injected with 0.1ml of samarium-153-EDTMP via orbital plexus (25µCi. After 2 hours, the animals were killed and samples of the brain, thyroid, lung, heart, stomach, colon, liver, kidney and both femurs were removed. The percentage radioactivity of each sample (% ATI/g was determined in an automatic gamma-counter (Wizard-1470, Perkin-Elmer, Finland. RESULTS: On the 9th day after the administration of the 2nd chemotherapy cycle, the rats had a significant weight loss (314.50±22.09g compared (pOBJETIVO: Muitos pacientes com metástases ósseas são tratados com radiofármacos associados com quimioterapia para alívio da dor óssea. O objetivo do trabalho foi estudar a influência do docetaxel na biodistribuição do EDTMP-153-samário nos ossos e outros órgãos de ratos. MÉTODOS: Ratos Wistar foram aleatoriamente alocados em 2 grupos de 6 animais cada. O grupo DS (docetaxel/samário recebeu docetaxel (15 mg/kg intraperitoneal em dois ciclos com 11 dias de intervalo. Os ratos do grupo S (samário/controle não foram tratados com docetaxel. Nove dias após a quimioterapia, todos os animais receberam 0,1ml de EDTMP-153-samário via plexo orbital (25µCi. Após 2 horas, os animais foram mortos e feitas biópsias de cérebro, tireóide, pulmão, coração, estômago, cólon, fígado, rim e fêmures. O percentual de radioatividade por grama (%ATI/g de tecido de cada bi

Sorption of sodium hydroxide by type I collagen and bovine corneas.

Science.gov (United States)

Whikehart, D R; Edwards, W C; Pfister, R R

1991-01-01

There are no quantitative studies on the uptake of alkali into corneal tissues. To study this phenomenon, both type I collagen and bovine corneas were incubated in sodium hydroxide (NaOH) under varying conditions for periods up to 27.5 h. The sorption (absorption or adsorption) of the alkali to protein and tissue was measured as the quantity of NaOH no longer available for titration to neutrality with hydrochloric acid. Sorption was found to be dependent on the concentration of NaOH (0.01-1 N) but independent of the incubation temperature (4-35 degrees C). In whole cornea, sorption of 1 N NaOH began immediately and increased with time up to 6 h. After 6 h, sorption decreased, together with the observed degradation and solubilization of the tissue. Stripping of the corneal endothelium alone or of the endothelium and epithelium increased sorption in a similar manner when compared to whole corneas for periods up to 4 h. These observations are compatible with ionic and nonionic bonding of hydroxide ions to collagen (including that of the cornea) and the subsequent release of hydroxide ions during hydrolysis of the protein itself. Indirect evidence also suggests the inclusion of quantities of unbound hydroxide ions in hydrated gels of glycosaminoglycans. It is proposed that in a chemical burn of the cornea, alkali is both stored in the tissue (by sorption) and reacted with it (by hydrolysis), without any net consumption of alkali taking place.

EFFECT OF SODIUM HYDROXIDE CONCENTRATION ON FRESH PROPERTIES AND COMPRESSIVE STRENGTH OF SELF-COMPACTING GEOPOLYMER CONCRETE

Directory of Open Access Journals (Sweden)

FAREED AHMED MEMON

2013-02-01

Full Text Available This paper reports the results of the laboratory tests conducted to investigate the effect of sodium hydroxide concentration on the fresh properties and compressive strength of self-compacting geopolymer concrete (SCGC. The experiments were conducted by varying the concentration of sodium hydroxide from 8 M to 14 M. Test methods such as Slump flow, V-Funnel, L-box and J-Ring were used to assess the workability characteristics of SCGC. The test specimens were cured at 70°C for a period of 48 hours and then kept in room temperature until the day of testing. Compressive strength test was carried out at the ages of 1, 3, 7 and 28 days. Test results indicate that concentration variation of sodium hydroxide had least effect on the fresh properties of SCGC. With the increase in sodium hydroxide concentration, the workability of fresh concrete was slightly reduced; however, the corresponding compressive strength was increased. Concrete samples with sodium hydroxide concentration of 12 M produced maximum compressive strength.

Hydrated proton and hydroxide charge transfer at the liquid/vapor interface of water

Energy Technology Data Exchange (ETDEWEB)

Soniat, Marielle; Rick, Steven W., E-mail: srick@uno.edu [Department of Chemistry, University of New Orleans, New Orleans, Louisiana 70148 (United States); Kumar, Revati [Department of Chemistry, Louisiana State University, Baton Rouge, Louisiana 70808 (United States)

2015-07-28

The role of the solvated excess proton and hydroxide ions in interfacial properties is an interesting scientific question with applications in a variety of aqueous behaviors. The role that charge transfer (CT) plays in interfacial behavior is also an unsettled question. Quantum calculations are carried out on clusters of water with an excess proton or a missing proton (hydroxide) to determine their CT. The quantum results are applied to analysis of multi-state empirical valence bond trajectories. The polyatomic nature of the solvated excess proton and hydroxide ion results in directionally dependent CT, depending on whether a water molecule is a hydrogen bond donor or acceptor in relation to the ion. With polyatomic molecules, CT also depends on the intramolecular bond distances in addition to intermolecular distances. The hydrated proton and hydroxide affect water’s liquid/vapor interface in a manner similar to monatomic ions, in that they induce a hydrogen-bonding imbalance at the surface, which results in charged surface waters. This hydrogen bond imbalance, and thus the charged waters at the surface, persists until the ion is at least 10 Å away from the interface.

Effect of supplementation with barley and calcium hydroxide on intake of Mediterranean shrubs

Directory of Open Access Journals (Sweden)

Dragan Skobic

2011-04-01

Full Text Available Maquis plant communities are one of the most varied vegetation types in the Mediterranean region and an important habitat for wild and domestic herbivores. Although the majority of these shrubs are nutritious, the secondary compounds are main impediments that reduce their forage value. In five experiments we determined the effect of supplementing goats with calcium hydroxide plus barley, and barley alone on intake of five dominant shrubs (Quercus ilex, Erica multiflora, Arbutus unedo, Viburnum tinus and Pistacia lentiscus of the Mediterranean maquis community. The combination of calcium hydroxide plus barley and barley alone increased utilization of all five investigated Mediterranean shrubs; therewith that intake of Arbutus unedo and Viburnum tinus was not statistically significant. Supplemented goats with calcium hydroxide plus barley or barley alone could be effective in controlling secondary compounds-rich Mediterranean shrubs where their abundance threatens biodiversity. This control can be facilitated by browsing dominant Mediterranean shrubs, which has been shown to be effective in managing Mediterranean maquis density. Calcium hydroxide and barley (energy enhance use of secondary compounds-containing plants, which may increase production of alternate forages and create a more diverse mix of plant species in the Mediterranean maquis plant community.

Gold Nanoparticles on Layered Double Hydroxide Nanosheets and Its Electrocatalysis for Glucose Oxidation

Energy Technology Data Exchange (ETDEWEB)

Cho, Hye Ran; Lee, Jong Hyeon [The Catholic University of Korea, Bucheon (Korea, Republic of); Cho, Se Hee; Ji, Hong Geun [H and A PharmaChem, Bucheon (Korea, Republic of)

2016-03-15

We developed a new way to form the well-defined nanocomposite of Au NPs and exfoliated LDH nanosheet by in situ chemical reduction with NaBH{sub 4}. The optical and structural studies indicate that the Au NPs are highly dispersed and immobilized on the surface of LDH nanosheets. The Au/LDH nanosheet exhibited an excellent electrocatalysis toward glucose oxidation reaction. The results strongly demonstrate that the nanoscopic natures and dense positive charges of LDH nanosheet effectively stabilized the Au NPs to maintain their inherent properties during the synthesis and the electrocatalysis. The use of the double hydroxide nanosheets as nanoscopic support materials for the transition-metal NPs will dramatically improve their functionalities in heterogeneous catalysis. Recently, two-dimensional nanosheet of exfoliated layered double hydroxide (LDH) has emerged as a new type of solid support to immobilize the diverse metal NPs because of the large metal hydroxide area, good biochemical stability, and highly charged positive potential of 1- to 2-nm thick LDH layers. LDHs consist of a continuous stack of positively charged metal hydroxide layers with counter anions and water molecules placed in interlayer spaces.

Hydrated proton and hydroxide charge transfer at the liquid/vapor interface of water

International Nuclear Information System (INIS)

Soniat, Marielle; Rick, Steven W.; Kumar, Revati

2015-01-01

The role of the solvated excess proton and hydroxide ions in interfacial properties is an interesting scientific question with applications in a variety of aqueous behaviors. The role that charge transfer (CT) plays in interfacial behavior is also an unsettled question. Quantum calculations are carried out on clusters of water with an excess proton or a missing proton (hydroxide) to determine their CT. The quantum results are applied to analysis of multi-state empirical valence bond trajectories. The polyatomic nature of the solvated excess proton and hydroxide ion results in directionally dependent CT, depending on whether a water molecule is a hydrogen bond donor or acceptor in relation to the ion. With polyatomic molecules, CT also depends on the intramolecular bond distances in addition to intermolecular distances. The hydrated proton and hydroxide affect water’s liquid/vapor interface in a manner similar to monatomic ions, in that they induce a hydrogen-bonding imbalance at the surface, which results in charged surface waters. This hydrogen bond imbalance, and thus the charged waters at the surface, persists until the ion is at least 10 Å away from the interface

Carbonation as a binding mechanism for coal/calcium hydroxide pellets. Final technical report, 1 September, 1992--31 August, 1993

Energy Technology Data Exchange (ETDEWEB)

Rapp, D.; Lytle, J.; Hackley, K.; Dagamac, M. [Illinois State Geological Survey, Champaign, IL (United States); Berger, R. [Univ. of Illinois, Urbana, IL (United States); Schanche, G. [Army Construction Engineering Research Lab., Champaign, IL (United States)

1993-12-31

This research was an investigation of calcium hydroxide, a sulfur-capturing sorbent, as a binder for coal fines. The reaction of carbon dioxide with calcium hydroxide, referred to as carbonation, was studied as a method for improving pellet quality. Carbonation forms a cementitious matrix of calcium carbonate. Research has demonstrated that calcium hydroxide is a viable binder for coal fines and that a roller-and-die pellet mill is an effective method of pellet formation. From a minus 28 mesh preparation plant fine coal sample, a roller-and-die pellet mill produced strong pellets when 5 and 10% calcium hydroxide was used as a binder. The pellets containing 10% calcium hydroxide strengthened considerably when air cured. This increase in strength was attributed to carbonation via atmospheric carbon dioxide. Pellets containing 10 wt% calcium hydroxide were produced using an extruder but pellets formed in this manner were much weaker than pellets produced with the roller-and-die mill. In tests performed using a laboratory hydraulic press, the effect of particle size and compaction pressure on pellet strength was studied. Particle distributions with mean sizes of 200, 90 and 40 microns were tested. The results indicate that pellet strength increased with decreasing particle size and increasing compaction pressure when calcium hydroxide was used as a binder. Pellets containing 10 wt% calcium hydroxide increased in strength by approximately 40% when air dried for one day. As above, this increase in strength was attributed to carbonation of the calcium hydroxide via atmospheric carbon dioxide.

Formation of iron (hydr)oxides during the abiotic oxidation of Fe(II) in the presence of arsenate.

Science.gov (United States)

Song, Jia; Jia, Shao-Yi; Yu, Bo; Wu, Song-Hai; Han, Xu

2015-08-30

Abiotic oxidation of Fe(II) is a common pathway in the formation of Fe (hydr)oxides under natural conditions, however, little is known regarding the presence of arsenate on this process. In hence, the effect of arsenate on the precipitation of Fe (hydr)oxides during the oxidation of Fe(II) is investigated. Formation of arsenic-containing Fe (hydr)oxides is constrained by pH and molar ratios of As:Fe during the oxidation Fe(II). At pH 6.0, arsenate inhibits the formation of lepidocrocite and goethite, while favors the formation of ferric arsenate with the increasing As:Fe ratio. At pH 7.0, arsenate promotes the formation of hollow-structured Fe (hydr)oxides containing arsenate, as the As:Fe ratio reaches 0.07. Arsenate effectively inhibits the formation of magnetite at pH 8.0 even at As:Fe ratio of 0.01, while favors the formation of lepidocrocite and green rust, which can be latterly degenerated and replaced by ferric arsenate with the increasing As:Fe ratio. This study indicates that arsenate and low pH value favor the slow growth of dense-structured Fe (hydr)oxides like spherical ferric arsenate. With the rapid oxidation rate of Fe(II) at high pH, ferric (hydr)oxides prefer to precipitate in the formation of loose-structured Fe (hydr)oxides like lepidocrocite and green rust. Copyright © 2015 Elsevier B.V. All rights reserved.

The corrosion of steels in molten sodium hydroxide

International Nuclear Information System (INIS)

Newman, R.N.; Smith, C.A.; Smith, R.J.

1976-09-01

The role of sodium hydroxide corrosion is discussed in relation to the wastage of materials observed in fast reactor boilers under fault conditions in the vicinity of a water leak into sodium. An experimental technique to study the corrosion under varying conditions is described. The results presented are for 2 1/4Cr 1Mo obtained in static sodium hydroxide in a closed volume over the temperature range 1033K to 1273K. It is found that the corrosion rate can be followed by monitoring the hydrogen produced by the reaction, which can be written as: Fe + 2NaOH = NaFeO 2 + NaH + 1/2H 2 . After an initial acceleration period the rate law is parabolic. The effect on the corrosion rate of melt and cover gas composition has been in part investigated, and the relevance of mass flow of reactants is discussed. (author)

Competitive reactions during synthesis of zinc aluminum layered double hydroxides by thermal hydrolysis of urea

DEFF Research Database (Denmark)

Staal, Line Boisen; Pushparaj, Suraj Shiv Charan; Forano, Claude

2017-01-01

Homogeneous precipitation by thermal hydrolysis of urea (“The urea method”) is preferred for the preparation of pure and highly crystalline layered double hydroxides (LDHs). However, our recent study revealed large concentrations of amorphous aluminum hydroxide (AOH) in several zinc(II) aluminum(...

Carbon dioxide absorbents containing potassium hydroxide produce much larger concentrations of compound A from sevoflurane in clinical practice.

Science.gov (United States)

Yamakage, M; Yamada, S; Chen, X; Iwasaki, S; Tsujiguchi, N; Namiki, A

2000-07-01

We investigated the concentrations of degraded sevoflurane Compound A during low-flow anesthesia with four carbon dioxide (CO(2)) absorbents. The concentrations of Compound A, obtained from the inspiratory limb of the circle system, were measured by using a gas chromatograph. In the groups administered 2 L/min fresh gas flow with 1% sevoflurane, when the conventional CO(2) absorbents, Wakolime(TM) (Wako, Tokyo, Japan) and Drägersorb(TM) (Dräger, Lübeck, Germany), were used, the concentrations of Compound A increased steadily from a baseline to 14.3 ppm (mean) and 13.2 ppm, respectively, at 2 h after exposure to sevoflurane. In contrast, when the other novel types of absorbents containing decreased or no potassium hydroxide/sodium hydroxide, Medisorb(TM) (Datex-Ohmeda, Louisville, CO) and Amsorb(TM) (Armstrong, Coleraine, Northern Ireland), were used, Compound A remained at baseline (potassium hydroxide/sodium hydroxide produce much larger concentrations of Compound A from sevoflurane in clinical practice. An absorbent containing neither potassium hydroxide nor sodium hydroxide produces the smallest concentrations of Compound A.

Polystyrene/magnesium hydroxide nanocomposite particles prepared by surface-initiated in-situ polymerization

International Nuclear Information System (INIS)

Liu Hui; Yi Jianhong

2009-01-01

In order to avoid their agglomeration and incompatibility with hydrophobic polystyrene substrate, magnesium hydroxide nanoparticles were encapsulated by surface-initiated in-situ polymerization of styrene. The process contained two steps: electrostatic adsorption of initiator and polymerization of monomer on the surface of magnesium hydroxide. It was found that high adsorption ratio in the electrostatic adsorption of initiator could be attained only in acidic region, and the adsorption belonged to typical physical process. Compared to traditional in-situ polymerization, higher grafting ratio was obtained in surface-initiated in-situ polymerization, which can be attributed to weaker steric hindrance. Both Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM) indicated that polystyrene/magnesium hydroxide nanocomposite particles had been successfully prepared by surface-initiated in-situ polymerization. The resulting samples were also analyzed and characterized by means of contact angle testing, dispersibility evaluation and thermogravimetric analysis

Hydroxide diffuses slower than hydronium in water because its solvated structure inhibits correlated proton transfer

Science.gov (United States)

Chen, Mohan; Zheng, Lixin; Santra, Biswajit; Ko, Hsin-Yu; DiStasio, Robert A., Jr.; Klein, Michael L.; Car, Roberto; Wu, Xifan

2018-03-01

Proton transfer via hydronium and hydroxide ions in water is ubiquitous. It underlies acid-base chemistry, certain enzyme reactions, and even infection by the flu. Despite two centuries of investigation, the mechanism underlying why hydroxide diffuses slower than hydronium in water is still not well understood. Herein, we employ state-of-the-art density-functional-theory-based molecular dynamics—with corrections for non-local van der Waals interactions, and self-interaction in the electronic ground state—to model water and hydrated water ions. At this level of theory, we show that structural diffusion of hydronium preserves the previously recognized concerted behaviour. However, by contrast, proton transfer via hydroxide is less temporally correlated, due to a stabilized hypercoordination solvation structure that discourages proton transfer. Specifically, the latter exhibits non-planar geometry, which agrees with neutron-scattering results. Asymmetry in the temporal correlation of proton transfer leads to hydroxide diffusing slower than hydronium.

Coordination Structure of Aluminum in Magnesium Aluminum Hydroxide Studied by 27Al NMR

Institute of Scientific and Technical Information of China (English)

无

2003-01-01

The coordination structure of aluminum in magnesium aluminum hydroxide was studiedby 27Al NMR. The result showed that tetrahedral aluminum (AlⅣ) existed in magnesiumaluminum hydroxide, and the contents of AlⅣ increased with the increase of the ratio of Al/Mg andwith the peptizing temperature. AlⅣ originated from the so-called Al13 polymer with the structureof one Al tetrahedron surrounded by twelve Al octahedrons.

Interaction of titanium and zirconium hydroxides with aqueous solutions of lead(2) salts

International Nuclear Information System (INIS)

Savenko, V.G.; Sakharov, V.V.; Nurgalieva, A.A.; Petrov, K.I.

1980-01-01

The mixed phases, characterized by the Pb : Zr 4 ratio are synthesized during the process of geterophase interaction of zirconium hydroxide with solutions of lead nitrate and acetate. The process of the mixed phases thermolysis on the base of amorphous zirconium hydroxides is investigated by the methods of DTA, X-ray phase analysis and IR spectroscopy. The metastable phases are formed during the thermolysis process

NO and SCN -intercalated layered double hydroxides: structure and ...

Indian Academy of Sciences (India)

2018-02-05

Feb 5, 2018 ... Keywords. Nitrite ion; thiocyanate ion; layered double hydroxide; structure refinement. 1. Introduction .... applications of LDHs is sorption/uptake of toxic anions ... by ion chromatography using a Metrohm Model 861 Advanced.

Aluminum phosphate shows more adjuvanticity than Aluminum hydroxide in recombinant hepatitis –B vaccine formulation

Directory of Open Access Journals (Sweden)

2008-08-01

Full Text Available Background: Although a number of investigation have been carried out to find alternative adjuvants to aluminum salts in vaccine formulations, they are still extensively used due to their good track record of safety, low cost and proper adjuvanticity with a variety of antigens. Adsorption of antigens onto aluminum compounds depends heavily on electrostatic forces between adjuvant and antigen. Commercial recombinant protein hepatitis B vaccines containing aluminum hydroxide as adjuvant is facing low induction of immunity in some sections of the vaccinated population. To follow the current global efforts in finding more potent hepatitis B vaccine formulation, adjuvanticity of aluminum phosphate has been compared to aluminum hydroxide. Materials and methods: The adjuvant properties of aluminum hydroxide and aluminum phosphate in a vaccine formulation containing a locally manufactured hepatitis B (HBs surface antigen was evaluated in Balb/C mice. The formulations were administered intra peritoneally (i.p. and the titers of antibody which was induced after 28 days were determined using ELISA technique. The geometric mean of antibody titer (GMT, seroconversion and seroprotection rates, ED50 and relative potency of different formulations were determined. Results: All the adjuvanicity markers obtained in aluminum phosphate formulation were significantly higher than aluminum hydroxide. The geometric mean of antibody titer of aluminum phosphate was approximately three folds more than aluminum hydroxide. Conclusion: Aluminum phosphate showed more adjuvanticity than aluminum hydroxide in hepatitis B vaccine. Therefore the use of aluminum phosphate as adjuvant in this vaccine may lead to higher immunity with longer duration of effects in vaccinated groups.

Organically pillared layered zinc hydroxides

International Nuclear Information System (INIS)

Kongshaug, K.O.; Fjellvaag, Helmer

2004-01-01

The two organically pillared layered zinc hydroxides [Zn 2 (OH) 2 (ndc)], CPO-6, and [Zn 3 (OH) 4 (bpdc)], CPO-7, were obtained in hydrothermal reactions between 2,6-naphthalenedicarboxylic acid (ndc) and zinc nitrate (CPO-6) and 4,4'biphenyldicarboxylate (bpdc) and zinc nitrate (CPO-7), respectively. In CPO-6, the tetrahedral zinc atoms are connected by two μ 2 -OH groups and two carboxylate oxygen atoms, forming infinite layers extending parallel to the bc-plane. These layers are pillared by ndc to form a three-dimensional structure. In CPO-7, the zinc hydroxide layers are containing four-, five- and six coordinated zinc atoms, and the layers are built like stairways running along the [001] direction. Each step is composed of three infinite chains running in the [010] direction. Both crystal structures were solved from conventional single crystal data. Crystal data for CPO-6: Monoclinic space group P2 1 /c (No. 14), a=11.9703(7), b=7.8154(5), c=6.2428(4) A, β=90.816(2) deg., V=583.97(6) A 3 and Z=4. Crystal data for CPO-7: Monoclinic space group C2/c (No. 15), a=35.220(4), b=6.2658(8), c=14.8888(17) A, β=112.580(4) deg., V=3033.8(6) A 3 and Z=8. The compounds were further characterized by thermogravimetric- and chemical analysis

Isotope exchange between alkaline earth metal hydroxide and HTO water in the equilibrium state

International Nuclear Information System (INIS)

Imaizumi, H.; Gounome, J.; Kano, N.

1997-01-01

In order reveal to what extent tritium ( 3 H or T) can be incorporated into hydroxides, the isotope exchange reaction (OT-for-OH exchange reaction) between each alkaline earth metal hydroxide (M(OH) 2 ), where M means alkaline earth metal (M=Ca, Sr or Ba) and HTO water was observed homogeneously at 30 deg C under equilibrium after mixing. Consequently, the followings were obtained: a quantitative relation between the electronegativity of each M ion and the ability (of the M ion) incorporating OT - into the M hydroxide can be found and the ability is small when the temperature is high, the exchange rate for the OT-for-OH exchange reaction is small when the electronegativity of the M ion in the M hydroxide is great, as for the dissociation of HTO water, it seems that formula (HTO ↔ T + + OH - ) is more predominant than the formula (HTO ↔H + + OT - ) when the temperature is high and the method used in this work is useful to estimate the reactivity of a certain alkaline material. (author)

Facile preparation of layered double hydroxide/MoS{sub 2}/poly(vinyl alcohol) composites

Energy Technology Data Exchange (ETDEWEB)

Zhou, Keqing, E-mail: zhoukq@cug.edu.cn [Faculty of Engineering, China University of Geosciences (Wuhan), 388 Lumo Road, Wuhan, Hubei, 430074 (China); Hu, Yixin [Department of Chemistry, Lanzhou University, Lanzhou 730000 (China); Liu, Jiajia [State Key Laboratory of Fire Science, University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui, 230026 (China); Gui, Zhou, E-mail: zgui@ustc.edu.cn [State Key Laboratory of Fire Science, University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui, 230026 (China); Jiang, Saihua [School of Mechanical and Automotive Engineering, South China University of Technology, Wushan Road 381, Guangzhou, 510641 (China); Tang, Gang [School of Architecture and Civil Engineering, Anhui University of Technology, 59 Hudong Road, Ma' anshan, Anhui, 243002 (China)

2016-08-01

In present study, the layered double hydroxide/MoS{sub 2} hybrids are facilely synthesized by self-assembly of exfoliated MoS{sub 2} nanosheets and layered double hydroxide nanoplates via electrostatic interaction, with the aim of combining their physical and chemical functionalities to form a promising nanofiller for flame retardancy in polymer composites. The structure and morphology of the layered double hydroxide/MoS{sub 2} hybrids are probed by X-ray diffraction and transmission electron microscopy. Subsequently, the hybrids are incorporated into poly (vinyl alcohol) to serve as reinforcements. The flame retardant efficiency of MoS{sub 2} nanosheets in poly (vinyl alcohol) is significantly enhanced after the incorporation of layered double hydroxide nanoplates, which can be explained by the forming of a compact and uniform char during combustion. - Highlights: • The LDH/MoS{sub 2} hybrids were facilely synthesized by self-assembly method. • The flame retardant efficiency of LDH/MoS{sub 2} hybrids in PVA was significantly enhanced. • It is a promising strategy for improving the flame retardant efficiency of MoS{sub 2}.

Thermal formation of corundum from aluminium hydroxides ...

Indian Academy of Sciences (India)

Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form -Al2O3 at ∼ 400°C but the formation of -Al2O3 at 1200°C occurs more readily in the material derived ...

Thermal formation of corundum from aluminium hydroxides ...

Indian Academy of Sciences (India)

Abstract. Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form γ-Al2O3 at ~ 400°C but the formation of α-Al2O3 at 1200°C occurs more readily in the material ...

Microwave-assisted synthesis of metal oxide/hydroxide composite electrodes for high power supercapacitors - A review

Science.gov (United States)

Faraji, Soheila; Ani, Farid Nasir

2014-10-01

Electrochemical capacitors (ECs), also known as pseudocapacitors or supercapacitors (SCs), is receiving great attention for its potential applications in electric and hybrid electric vehicles because of their ability to store energy, alongside with the advantage of delivering the stored energy much more rapidly than batteries, namely power density. To become primary devices for power supply, supercapacitors must be developed further to improve their ability to deliver high energy and power simultaneously. In this concern, a lot of effort is devoted to the investigation of pseudocapacitive transition-metal-based oxides/hydroxides such as ruthenium oxide, manganese oxide, cobalt oxide, nickel oxide, cobalt hydroxide, nickel hydroxide, and mixed metal oxides/hydroxides such as nickel cobaltite and nickel-cobalt oxy-hydroxides. This is mainly due to the fact that they can produce much higher specific capacitances than typical carbon-based electric double-layer capacitors and electronically conducting polymers. This review presents supercapacitor performance data of metal oxide thin film electrodes by microwave-assisted as an inexpensive, quick and versatile technique. Supercapacitors have established the specific capacitance (Cs) principles, therefore, it is likely that metal oxide films will continue to play a major role in supercapacitor technology and are expected to considerably increase the capabilities of these devices in near future.

CALCIUM HYDROXIDE IN ENDODONTIC TREATMENT OF PERIAPICALLY INFECTED TEETH

Directory of Open Access Journals (Sweden)

Rahmi Alma Farah Adang

2006-04-01

Full Text Available An inadequate endodontic treatment may affect the root canal system and spread beyond its apical foramina that elicit periodontal tissue developing into abscess, granuloma and radicular cyst. Periodical lesions can be treated with non surgical endodontic treatment using calcium hydroxide dressing. This case study is reporting teeth 11 with periodical lesions and infection. Evidence of a clinical healing and radiographic assessments were followed by a non surgical endodontic therapy. Successful treatment outcome is related to the elimination of infection agents from the root canal. This can activate a stimulation zone to promote regeneration. Calcium hydroxide used as a root canal dressing may promote alkalinity at the adjacent tissue , create favourable environmental condition in which hard tissue formation can occur, interfere the bactericidal activity, increase mineralization, and induce healing.

Calorimetric study of interaction of barium hydroxide with diluted solutions of hydrofluoric acid

International Nuclear Information System (INIS)

Kurbanov, A.R.; Sharipov, D.Sh.

1993-01-01

Present article is devoted to calorimetric study of interaction of barium hydroxide with diluted solutions of hydrofluoric acid. The calorimetric study of interaction of barium hydroxide with diluted solutions of hydrofluoric acid was carried out in order to determine the thermal effects of reactions. The results of interaction of Ba(OH) 4 ·8H 2 O with 5, 10, and 20% solution of hydrofluoric acid were considered.

Interaction of pristine hydrotalcite-like layered double hydroxides ...

Indian Academy of Sciences (India)

Metal oxides in general have surface acidic sites, but for exceptional circumstances, are not expected to mineralize CO2. Given their intrinsic basicity and an expandable interlayer gallery, the hydrotalcite-like layered double hydroxides (LDHs) are expected to be superior candidate materials for CO2 mineralization.

Development of Drug Delivery Systems Based on Layered Hydroxides for Nanomedicine

Directory of Open Access Journals (Sweden)

Farahnaz Barahuie

2014-05-01

Full Text Available Layered hydroxides (LHs have recently fascinated researchers due to their wide application in various fields. These inorganic nanoparticles, with excellent features as nanocarriers in drug delivery systems, have the potential to play an important role in healthcare. Owing to their outstanding ion-exchange capacity, many organic pharmaceutical drugs have been intercalated into the interlayer galleries of LHs and, consequently, novel nanodrugs or smart drugs may revolutionize in the treatment of diseases. Layered hydroxides, as green nanoreservoirs with sustained drug release and cell targeting properties hold great promise of improving health and prolonging life.

Density-functional tight-binding investigation of the structure, stability and material properties of nickel hydroxide nanotubes

Science.gov (United States)

Jahangiri, Soran; Mosey, Nicholas J.

2018-01-01

Nickel hydroxide is a material composed of two-dimensional layers that can be rolled up to form cylindrical nanotubes belonging to a class of inorganic metal hydroxide nanotubes that are candidates for applications in catalysis, energy storage, and microelectronics. The stabilities and other properties of this class of inorganic nanotubes have not yet been investigated in detail. The present study uses self-consistent-charge density-functional tight-binding calculations to examine the stabilities, mechanical properties, and electronic properties of nickel hydroxide nanotubes along with the energetics associated with the adsorption of water by these systems. The tight-binding model was parametrized for this system based on the results of first-principles calculations. The stabilities of the nanotubes were examined by calculating strain energies and performing molecular dynamics simulations. The results indicate that single-walled nickel hydroxide nanotubes are stable at room temperature, which is consistent with experimental investigations. The nanotubes possess size-dependent mechanical properties that are similar in magnitude to those of other inorganic nanotubes. The electronic properties of the nanotubes were also found to be size-dependent and small nickel oxyhydroxide nanotubes are predicted to be semiconductors. Despite this size-dependence, both the mechanical and electronic properties were found to be almost independent of the helical structure of the nanotubes. The calculations also show that water molecules have higher adsorption energies when binding to the interior of the nickel hydroxide nanotubes when compared to adsorption in nanotubes formed from other two-dimensional materials such as graphene. The increased adsorption energy is due to the hydrophilic nature of nickel hydroxide. Due to the broad applications of nickel hydroxide, the nanotubes investigated here are also expected to be used in catalysis, electronics, and clean energy production.

Synthetic Applications and Mechanistic Studies of the Hydroxide-Mediated Cleavage of Carbon-Carbon Bonds in Ketones

DEFF Research Database (Denmark)

Mazziotta, Andrea; Makarov, Ilya S.; Fristrup, Peter

2017-01-01

The hydroxide-mediated cleavage of ketones into alkanes and carboxylic acids has been reinvestigated and the substrate scope extended to benzyl carbonyl compounds. The transformation is performed with a 0.05 M ketone solution in refluxing xylene in the presence of 10 equiv of potassium hydroxide....... The reaction constitutes a straightforward protocol for the synthesis of certain phenyl-substituted carboxylic acids from 2-phenylcycloalkanones. The mechanism was investigated by kinetic experiments which indicated a first order reaction in hydroxide and a full negative charge in the rate-determining step....... The studies were complemented by a theoretical investigation where two possible pathways were characterized by DFT/M06-2X. The calculations showed that the scission takes place by nucleophilic attack of hydroxide on the ketone followed by fragmentation of the resulting oxyanion into the carboxylic acid...

Synthetic Applications and Mechanistic Studies of the Hydroxide-Mediated Cleavage of Carbon-Carbon Bonds in Ketones.

Science.gov (United States)

Mazziotta, Andrea; Makarov, Ilya S; Fristrup, Peter; Madsen, Robert

2017-06-02

The hydroxide-mediated cleavage of ketones into alkanes and carboxylic acids has been reinvestigated and the substrate scope extended to benzyl carbonyl compounds. The transformation is performed with a 0.05 M ketone solution in refluxing xylene in the presence of 10 equiv of potassium hydroxide. The reaction constitutes a straightforward protocol for the synthesis of certain phenyl-substituted carboxylic acids from 2-phenylcycloalkanones. The mechanism was investigated by kinetic experiments which indicated a first order reaction in hydroxide and a full negative charge in the rate-determining step. The studies were complemented by a theoretical investigation where two possible pathways were characterized by DFT/M06-2X. The calculations showed that the scission takes place by nucleophilic attack of hydroxide on the ketone followed by fragmentation of the resulting oxyanion into the carboxylic acid and a benzyl anion.

Hydrothermal synthesis of nickel hydroxide nanostructures in mixed solvents of water and alcohol

International Nuclear Information System (INIS)

Yang Lixia; Zhu Yingjie; Tong Hua; Liang Zhenhua; Li Liang; Zhang Ling

2007-01-01

Nickel hydroxide nanosheets and flowers have been hydrothermally synthesized using Ni(CH 3 COO) 2 .4H 2 O in mixed solvents of ethylene glycol (EG) or ethanol and deionized water at 200 deg. C for different time. The phase and morphology of the obtained products can be controlled by adjusting the experimental parameters, including the hydrothermal time and the volume ratio of water to EG or ethanol. The possible reaction mechanism and growth of the nanosheets and nanoflowers are discussed based on the experimental results. Porous nickel oxide nanosheets are obtained by heating nickel hydroxide nanosheets in air at 400 deg. C. The products were characterized by using various methods including X-ray diffraction (XRD), fourier transform infrared (FTIR), transmission electron microscopy (TEM), selected-area electron diffraction (SAED), field emission scanning electron microscopy (FESEM). The electrochemical property of β-Ni(OH) 2 nanosheets was investigated through the cyclic voltammogram (CV) measurement. - Graphical abstract: Nickel hydroxide nanosheets and flowers have been hydrothermally synthesized using Ni(CH 3 COO) 2 .4H 2 O in mixed solvents of ethylene glycol (EG) or ethanol and deionized water at 200 deg. C for different reaction time. Porous nickel oxide nanosheets are obtained by heating nickel hydroxide nanosheets in air at 400 deg. C

ADSORPTION OF PITCH AND STICKIES ON MAGNESIUM ALUMINUM HYDROXIDES TREATED AT DIFFERENT TEMPERAURES

Directory of Open Access Journals (Sweden)

Guodong Li

2011-04-01

Full Text Available Magnesium aluminum hydroxides (MAH of nitrate and carbonate forms were prepared by co-precipitation, dried at different temperatures, and employed as an adsorbent for pitch and stickies in papermaking. Results indicated that MAH that had been heat-treated had higher adsorption capacity to model pitch and stickies at neutral pH. Low-temperature-dried magnesium aluminum hydroxides of nitrate form (MAH-NO3 had higher adsorption capacity to model pitch and model stickies than those of the carbonate form (MAH-CO3. Increasing the drying temperature of MAH reduced the difference of adsorption capacity between MAH-NO3 and MAH-CO3. Higher-temperature-dried magnesium aluminum hydroxides also showed higher adsorption capacity to model pitch and stickies when the drying temperature was lower than 550 oC. MAH displayed higher adsorption capacity while a lower initial adsorption rate of model stickies than of model pitch. The model pitch and stickies were adsorbed on MAH significantly by charge neutralization and distributed mainly on the surface of the platelets of magnesium aluminum hydroxides. The experimental isothermal adsorption data of model pitch and stickies on MAH dried at 500 oC fit well to the Freundlich and Dubinin–Radushkevich isotherm equations.

Synthetic Applications and Mechanistic Studies of the Hydroxide-Mediated Cleavage of Carbon-Carbon Bonds in Ketones

DEFF Research Database (Denmark)

Mazziotta, Andrea; Makarov, Ilya S.; Fristrup, Peter

2017-01-01

The hydroxide-mediated cleavage of ketones into alkanes and carboxylic acids has been reinvestigated and the substrate scope extended to benzyl carbonyl compounds. The transformation is performed with a 0.05 M ketone solution in refluxing xylene in the presence of 10 equiv of potassium hydroxide....... The studies were complemented by a theoretical investigation where two possible pathways were characterized by DFT/M06-2X. The calculations showed that the scission takes place by nucleophilic attack of hydroxide on the ketone followed by fragmentation of the resulting oxyanion into the carboxylic acid...

Comparison of Calcium Hydroxide and Bioactive Glass after Direct Pulp Capping in Primary Teeth

Directory of Open Access Journals (Sweden)

R. Haghgoo

2007-12-01

Full Text Available Objective: Bioactive glass is often used as a filler material for repair of dental bone defects.In different studies osteogenic potential of this material was proved, but its dentinogenesisproperty is in doubt. The purpose of this study was to evaluate the histological pulp responses of Calcium hydroxide and Bioactive glass placed directly on exposed pulp tissues.Materials and Methods: Twenty teeth to be extracted due to orthodontic reasons were selected. These teeth were divided into two groups and treated with direct pulp capping.Calcium hydroxide was used for 10 teeth and Bioactive glass for 10 teeth. After 60 daysthe teeth were extracted and prepared for histological evaluation. Finally the data was analyzed with exact Fisher test.Results: All teeth treated with Calcium hydroxide showed inflammation. Internal resorption was seen in six teeth, abscess in five teeth and dentinal bridge in two teeth. Inflammationwas seen in three Bioactive glass samples and dentinal bridge in seven teeth, but internal resorption and abscess were not seen.Conclusion: Bioactive glass appears to be superior to Calcium hydroxide as a pulp capping agent in primary teeth.

Development and evaluation of copper-67 and samarium-153 labeled conjugates for tumor radioimmunotherapy

International Nuclear Information System (INIS)

Srivastava, S.C.; Mausner, L.F.; Mease, R.C.; Meinken, G.E.; Joshi, V.; Kolsky, K.; Sweet, M.; Steplewski, Z.

1995-01-01

The potential of utilizing receptor-specific agents such as monoclonal antibodies (MAb), and MAb-derived smaller molecules, as carriers of radionuclides for the selective destruction of tumors has stimulated much research activity. The success of such applications depends on many factors, especially the tumor binding properties of the antibody reagent, the efficiency of labeling and in-vivo stability of the radioconjugate and, on the careful choice of the radionuclide best suited to treat the tumor under consideration. The radiolabeled antibody technique for radioimmunotherapy (RIT), however, has experienced many limitations, and its success has not matched the expectations that were raised more than a decade ago. The problems that have been identified include: (i) degradation of antibody immunoreactivity resulting from chemical manipulations required for labeling; (ii) lack of suitable radioisotopes and methods for stable attachment of the radiolabel; (iii) in-vivo instability of the radioimmunoconjugates; (iv) excessive accumulation of activity in non-target locations; and (v) lack of radioimmunoconjugate accessibility to cells internal to a tumor mass. A careful choice of the radionuclide(s) best suited to treat the tumor under consideration is one of the most important requirements for successful radioimmunotherapy. This study evaluates copper 67 and samarium 153 for tumor radioimmunotherapy

Electronic spectra of anions intercalated in layered double hydroxides

Indian Academy of Sciences (India)

groups of the layers and interlayer water through the termi- nal atom symmetry ... results in a reaction with the metal hydroxide layers lead- ing to the ..... List of band positions observed for potassium salts of anion and LDH samples. Salts.

Synthesis of neodymium hydroxide nanotubes and nanorods by soft chemical process.

Science.gov (United States)

Shi, Weidong; Yu, Jiangbo; Wang, Haishui; Yang, Jianhui; Zhang, Hongjie

2006-08-01

A facile soft chemical approach using cetyltrimethylammonium bromide (CTAB) as template is successfully designed for synthesis of neodymium hydroxide nanotubes. These nanotubes have an average outer diameter around 20 nm, inner diameter around 2 nm, and length ranging from 100 to 120 nm, high BET surface area of 495.71 m(2) g(-1). We also find that neodymium hydroxide nanorods would be obtained when CTAB absented in reaction system. The Nd(OH)3 nanorods might act as precursors that are converted into Nd2O3 nanorods through dehydration at 550 degrees C. The nanorods could exhibit upconversion emission characteristic under excitation of 591 nm at room temperature.

Characterization and supercapacitor application of coin-like β-nickel hydroxide nanoplates

International Nuclear Information System (INIS)

Li Hongliang; Liu Suqin; Huang Chenghuan; Zhou Zhi; Li Yanhua; Fang Dong

2011-01-01

Coin-like nickel hydroxide nanoplates are synthesized via a simple coordination homogeneous precipitation method. The structure and morphology of as-prepared products are characterized by X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy and scanning electron microscopy. It is demonstrated that the products are typical β-nickel hydroxide with bunches coin-like nanoplates morphology. The electrochemical properties of coin-like β-Ni(OH) 2 are examined by cyclic voltammetric, chronopotentiometry and electrochemical impedance spectroscope. Cyclic voltammetric studies show that the electrodes have good reversibility. A specific capacitance of 1532 F g −1 is obtained at a charge/discharge current density of 0.2 A g −1 .

Ionic Strength-Controlled Mn (Hydr)oxide Nanoparticle Nucleation on Quartz: Effect of Aqueous Mn(OH)2.

Science.gov (United States)

Jung, Haesung; Jun, Young-Shin

2016-01-05

The early formation of manganese (hydr)oxide nanoparticles at mineral-water interfaces is crucial in understanding how Mn oxides control the fate and transport of heavy metals and the cycling of nutrients. Using atomic force microscopy, we investigated the heterogeneous nucleation and growth of Mn (hydr)oxide under varied ionic strengths (IS; 1-100 mM NaNO3). Experimental conditions (i.e., 0.1 mM Mn(2+) (aq) concentration and pH 10.1) were chosen to be relevant to Mn remediation sites. We found that IS controls Mn(OH)2 (aq) formation, and that the controlled Mn(OH)2 (aq) formation can affect the system's saturation and subsequent Mn(OH)2 (s) and further Mn3O4 (s) nanoparticle formation. In 100 mM IS system, nucleated Mn (hydr)oxide particles had more coverage on the quartz substrate than those in 1 mM and 10 mM IS systems. This high IS also resulted in low supersaturation ratio and thus favor heterogeneous nucleation, having better structural matching between nucleating Mn (hydr)oxides and quartz. The unique information obtained in this work improves our understanding of Mn (hydr)oxide formation in natural as well as engineered aqueous environments, such as groundwater contaminated by natural leachate and acid mine drainage remediation.

40 CFR 721.10018 - Calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3).

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Calcium hydroxide oxide silicate (Ca6... New Uses for Specific Chemical Substances § 721.10018 Calcium hydroxide oxide silicate (Ca6(OH)2O2... substance identified as calcium hydroxide oxide silicate (Ca6(OH)2O2(Si2O5)3) (PMN P-01-442; CAS No. 13169...

Removal of Indigo Carmine Dye from Aqueous Solution Using Magnesium Hydroxide as an Adsorbent

Directory of Open Access Journals (Sweden)

Thimmasandra Narayan Ramesh

2015-01-01

Full Text Available Magnesium hydroxide is used as an adsorbent for the removal of indigo carmine dye from aqueous solution. We have investigated the effectiveness of removal of indigo carmine dye from aqueous solutions at pH 6-7 and 12-13 using magnesium hydroxide thereby varying the dose of the adsorbent, concentration of the dye, duration, and temperature. Structural transformations of adsorbent during the adsorption process at different pH values are monitored using powder X-ray diffraction and infrared spectroscopy. Different types of adsorption isotherm models were evaluated and it was found that Langmuir isotherm fits well at both pH values (6-7 and 12-13. Adsorption of indigo carmine onto magnesium hydroxide at pH 6-7/pH 12-13 follows pseudo-second order rate kinetics.

Recovery of sodium hydroxide and silica from zirconium oxide plant effluent of Nuclear Fuel Complex

International Nuclear Information System (INIS)

Bajpai, M.B.; Shenoi, M.R.K.; Keni, V.S.

1994-01-01

Sodium hydroxide (lye) and silica can be recovered in pure form from the alkaline sodium silicate waste of Nuclear Fuel Complex, Hyderabad. Electrolytic method was used to amalgamate the sodium present in an electrolyser with flowing mercury as cathode and nickel as anode. The amalgam is then denuded with water in a graphite packed tower to recover mercury for recycling to the electrolyser and sodium hydroxide lye. Sodium hydroxide lye can be recycled in the zirconium oxide plant. Silica is recovered from the spent electrolyte by ion exchange method using cation exchange resin. Both the process details are described in this paper, with experimental data useful for the scale up. The process converts waste to value products. (author)

Graphene oxide/ferric hydroxide composites for efficient arsenate removal from drinking water

International Nuclear Information System (INIS)

Zhang Kai; Dwivedi, Vineet; Chi Chunyan; Wu Jishan

2010-01-01

A series of novel composites based on graphene oxide (GO) cross-linked with ferric hydroxide was developed for effective removal of arsenate from contaminated drinking water. GO, which was used as a supporting matrix here, was firstly treated with ferrous sulfate. Then, the ferrous compound cross-linked with GO was in situ oxidized to ferric compound by hydrogen peroxide, followed by treating with ammonium hydroxide. The morphology and composition of the composites were analyzed by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The ferric hydroxide was found to be homogenously impregnated onto GO sheets in amorphous form. These composites were evaluated as absorbents for arsenate removal from contaminated drinking water. For the water with arsenate concentration at 51.14 ppm, more than 95% of arsenate was absorbed by composite GO-Fe-5 with an absorption capacity of 23.78 mg arsenate/g of composite. Effective arsenate removal occurred in a wide range of pH from 4 to 9. However, the efficiency of arsenate removal was decreased when pH was increased to higher than 8.

Sorption of small amounts of europium(III) on iron(III) hydroxide and oxide

International Nuclear Information System (INIS)

Music, S.; Gessner, M.; Wolf, R.H.H.

1979-01-01

The sorption of small amounts of europium(III) on iron(III) hydroxide and oxide has been studied as a function of pH. The mechanism of sorption is discussed. Optimum conditions have been found for the preconcentration of small or trace amounts of europium(III) by iron(III) hydroxide and oxide. The influence of complexing agents (EDTA, oxalate, tartrate and 5-sulfosalicylic acid) on the sorption of small amounts of europium(III) on iron(III) oxide has also been studied. (author)

Determination of adsorbed protein concentration in aluminum hydroxide suspensions by near-infrared transmittance Spectroscopy

DEFF Research Database (Denmark)

Lai, Xuxin; Zheng, Yiwu; Jacobsen, Susanne

2008-01-01

, using the partial least square regression (PLSR) method to construct a calibration model. The linear concentration range of adsorbed BSA is from 0 to 1.75 mg/mL by using 10 mm path length cuvettes. The influence of the sedimentation in suspension, different buffers, and different aluminum hydroxide......Analysis of aluminum hydroxide based vaccines is difficult after antigen adsorption. Adsorbed protein is often assessed by measuring residual unadsorbed protein for quality control. A new method for the direct determination of adsorbed protein concentration in suspension using near-infrared (NIR......) transmittance spectroscopy is proposed here. A simple adsorption system using albumin from bovine serum (BSA) and aluminum hydroxide as a model system is employed. The results show that the NIR absorbance at 700-1300 nm is correlated to the adsorbed BSA concentration, measured by the ultraviolet (UV) method...

Separation of Yttrium from Rare Earth Concentrates in Fractional Hydroxide Precipitation

International Nuclear Information System (INIS)

Tri Handini; Purwoto; Mulyono

2007-01-01

Yttrium has been separated from rare earth concentrates by precipitation in fractional hydroxide using urea. The purpose of this research is to increase the yttrium rate resulting from the sedimentary process through separation of yttrium from other rare earth in fractional hydroxide precipitation using urea. In this research, we study the process variable of the concentration of urea, the ratio of feed volume to condensation volume of urea, as well as the temperature. Determination analysis of the rare earth rate is conducted using an X-ray spectrometer. The best result Y=92.89 % is obtained at a concentration of urea of 50 %, a level of precipitation of 3 times, and a temperature of 80°C. (author)

Recovery of sodium hydroxide and silica from zirconium oxide plant effluent of Nuclear Fuel Complex

Energy Technology Data Exchange (ETDEWEB)

Bajpai, M B; Shenoi, M R.K.; Keni, V S [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Sodium hydroxide (lye) and silica can be recovered in pure form from the alkaline sodium silicate waste of Nuclear Fuel Complex, Hyderabad. Electrolytic method was used to amalgamate the sodium present in an electrolyser with flowing mercury as cathode and nickel as anode. The amalgam is then denuded with water in a graphite packed tower to recover mercury for recycling to the electrolyser and sodium hydroxide lye. Sodium hydroxide lye can be recycled in the zirconium oxide plant. Silica is recovered from the spent electrolyte by ion exchange method using cation exchange resin. Both the process details are described in this paper, with experimental data useful for the scale up. The process converts waste to value products. (author). 3 figs., 2 tabs.

Interaction of pristine hydrotalcite-like layered double hydroxides ...

Indian Academy of Sciences (India)

1783–1790. c Indian Academy of Sciences. ... adversely impacts the ability of the metal hydroxide layer to interact with CO2 in the gas ... CO2 is a greenhouse gas and the bulk of anthropogenic CO2 ... decomposes by the release of gaseous CO2 and water in ... systems such as [Co–Al] LDH the decomposition tempera-.

Application of nanodimensional particles and aluminum hydroxide nanostructures for cancer diagnosis and therapy

Science.gov (United States)

Korovin, M. S.; Fomenko, A. N.

2017-09-01

Nanoparticles and nanostructured materials are one of the most promising developments for cancer therapy. Gold nanoparticles, magnetic nanoparticles based on iron and its oxides and other metal oxides have been widely used in diagnosis and treatment of cancer. Much less researchers' attention has been paid to nanoparticles and nanostructures based on aluminum oxides and hydroxides as materials for cancer diagnosis and treatment. However, recent investigations have shown promising results regarding these objects. Here, we review the antitumor results obtained with different aluminum oxide/hydroxide nanoparticles and nanostructures.

Preparation and properties of Mg/Al layered double hydroxide-oleate and -stearate intercalation compounds

International Nuclear Information System (INIS)

Inomata, Kazuya; Ogawa, Makoto

2006-01-01

Mg/Al layered double hydroxide-oleate and -stearate intercalation compounds were successfully synthesized by the reconstruction method under hydrothermal conditions from calcined hydrotalcite. The intercalation compounds were characterized by the high structural regularity as evidenced by the sharp and intense X-ray diffraction peaks. The oleate intercalated layered double hydroxide exhibits unique physicochemical properties such as a reversible thermoresponsive change in the basal spacing and swelling in organic solvents such as n-alkanes. (author)

Effect of the Association of Nonsteroidal Anti-inflammatory and Antibiotic Drugs on Antibiofilm Activity and pH of Calcium Hydroxide Pastes.

Science.gov (United States)

de Freitas, Rafaela Pignatti; Greatti, Vanessa Raquel; Alcalde, Murilo Priori; Cavenago, Bruno Cavalini; Vivan, Rodrigo Ricci; Duarte, Marco Antonio Hungaro; Weckwerth, Ana Carolina Villas Bôas; Weckwerth, Paulo Henrique

2017-01-01

The objective of the present study was to evaluate the in vitro antibiofilm activity and pH of calcium hydroxide associated with different nonsteroidal anti-inflammatory drugs (NSAIDs). The groups analyzed were as follows: group 1, calcium hydroxide paste with propylene glycol; group 2, calcium hydroxide paste with propylene glycol + 5% diclofenac sodium; group 3, calcium hydroxide paste with propylene glycol + 5% ibuprofen; group 4, calcium hydroxide paste with propylene glycol + 5% ciprofloxacin; and group 6, positive control (without medication). For analysis of the pH, the pastes were inserted into tubes and immersed in flasks containing ultrapure water. At the time intervals of 3, 24, 72, and 168 hours, the pH was measured with a calibrated pH meter. For microbial analysis, biofilm was induced in 30 bovine dentin blocks for 21 days. Subsequently, the pastes were placed on the blocks with biofilm for 7 days. Afterward, the pastes were removed by irrigation with sterile water, and the specimens were analyzed with a laser scanning confocal microscope with the 50 μL Live/Dead BacLight Bacterial Viability solution L7012 Kit (Molecular Probes, Inc, Eugene, OR). Data were subjected to statistical analysis at a significance level of 5%. The highest pH values were found for calcium hydroxide associated with ciprofloxacin in all periods analyzed. With the exception of pure calcium hydroxide paste, the other groups showed statistically significant differences (P antibiotic did not interfere with the pH of calcium hydroxide paste and increased the antimicrobial action of calcium hydroxide paste against Enterococcus faecalis biofilm formation. Published by Elsevier Inc.

Synthesis of beta alumina from aluminum hydroxide and oxyhydroxide precursors

CSIR Research Space (South Africa)

Van Zyl, A

1993-02-01

Full Text Available Two aluminium oxyhydroxides, boehmite and pseudoboehmite, and two aluminium hydroxides, bayerite and gibbsite, have been investigated as precursors for the synthesis of the solid electrolyte, beta alumina. Reaction pathways and products have been...

Ammonia induced precipitation of cobalt hydroxide: observation of turbostratic disorder

Science.gov (United States)

Ramesh, T. N.; Rajamathi, Michael; Kamath, P. Vishnu

2003-05-01

Cobalt hydroxide freshly precipitated from aqueous solutions of Co salts using ammonia, is a layered phase having a 9.17 Å interlayer spacing. DIFFaX simulations of the PXRD pattern reveal that it is turbostratically disordered.

Preparation of magnesium hydroxide nanoflowers from boron mud via anti-drop precipitation method

Energy Technology Data Exchange (ETDEWEB)

Ma, Xi [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Blue Sky Technology Corporation, Beijing 100083 (China); Ma, Hongwen, E-mail: mahw@cugb.edu.cn [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Jiang, Xiaoqian [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Jiang, Zhouqing [School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Blue Sky Technology Corporation, Beijing 100083 (China)

2014-08-15

Highlights: • We use the anti-drop precipitation method for synthesis of magnesium hydroxide. • Boron mud which is solid waste from a borax factory is used as the magnesium source. • The magnesium hydroxide nanoflowers are prepared in a short time. • The as-prepared magnesium hydroxide can be used as an effective flame retardant. - Abstract: Using boron mud as the starting material, the flower-like magnesium hydroxide (MH) has been successfully prepared via anti-drop precipitation method. The effect of NH{sub 3}·H{sub 2}O concentration, aging time, and surfactant on the morphology of MH was investigated. The optimum precipitation conditions are dropping MgSO{sub 4} solution in 5% NH{sub 3}·H{sub 2}O solution, with 3% polyethylene glycol as surfactant, aging for 30 min. XRD, SEM, FI-IR, and TG/DTA have been employed to characterize the as-prepared samples. XRD reveals that MH with high purity has the brucite structure. SEM images show that the flower-like MH exists in the form of mono-disperse well uniform spherical aggregation with diameter of 3–5 μm. TG/DTA shows a total percentage of weight loss 33.6% with a well-defined endothermic peak near 381.3 °C corresponding to the decomposition of MH. Furthermore, it reports that the extremely fast primary nucleation is of significance for crystal growth of MH.

Comparative study of 5% and 2.5% potassium hydroxide solution for molluscum contagiosum in children.

Science.gov (United States)

Uçmak, Derya; Akkurt, Meltem Zeynep; Kacar, Seval Dogruk; Sula, Bilal; Arica, Mustafa

2014-03-01

Molluscum contagiosum (MC) is a pediatric viral infection that is fairly contagious. Although various treatment methods are available, the presence of facial lesions limits options of therapy. We aimed to test an alternative treatment consisting of application of two different concentrations of potassium hydroxide (of KOH 5% solution and of KOH 2.5% solution) aqueous solution. In this study we evaluated the effectiveness and side-effects of daily applications of potassium hydroxide (KOH) aqueous solution at 2.5% and 5% concentrations, twice daily in 29 children with MC. Out of a total of 29 patients with molluscum contagiosum included in the study, 13 patients in the 2.5% KOH group and 12 patients in the KOH 5% group completed the study. Families were instructed to apply potassium hydroxide twice a day. The assessment of response and side-effects were performed on days 0, 15, 30, 45 and 60 (visits were numbered 1, 2, 3, 4 and 5, respectively) and one month after. We had a total of 11 (44%) patients who completely recovered after the fifth visit. While eight (66.7%) of these 11 patients were in the 5% treatment group, three (23.1%) patients were in the 2.5% treatment group, and there was a statistically meaningful difference (p Potassium hydroxide solution at a concentration of 5% was more effective than 2.5% in our patients. The treatment was well-tolerated on the face with the advantage of administration of lower concentrations. This study suggests potassium hydroxide may be a more preferable mode of treatment for molluscum contagiosum lesions on the face.

Research on the removal of radium from uranium effluent by air-aeration hydrated manganese hydroxide adsorption

International Nuclear Information System (INIS)

Zhang Jianguo; Chen Shaoqing; Qi Jing

2002-01-01

In the acidic leaching uranium process, pyrolusite or manganese oxide (MnO 2 ) powder is often used as an oxidizer. In the processed effluent, manganese ion present as a contaminant in addition to U, Ra, Th, As, Zn, Cu, F, SO 4 2- , etc. Manganese ion content is about 100∼200 mg/1 in effluent. In this case, a new process technique can be developed to treat the effluent using the Mn 2+ present in the effluent. The approach is as follows: The effluent is neutralized by lime milk to pH about 11. As a result, most contaminants are precipitated to meet the uranium effluent discharge standards (U, Th, Mn, SO 4 2- etc.), but radium is still present in the effluent. In this process, manganese ion forms manganese hydroxide Mn(OH) 2 . The manganese hydroxide is easily to oxide to form MnO(OH) 2 by air aeration. This hydrated manganese hydroxide complex can then be used to adsorb radium in effluent. The experiments show: (1) Effluent pH, manganese concentration in effluent, and aeration strength and time etc. influence the radium removal efficiency. Under the test conditions, when manganese in effluent is between 100∼300 mg/l, and pH is over 10.5, radium can be reduced to lower 1.11 Bq/1 in the processed effluent. Higher contents of impurity elements such as aluminum, silicon and magnesium in the effluent affect the removal efficiency; (2) Under the experimental conditions, the lime precipitation air-aeration formed hydrated manganese hydroxide complex sludge is stable. There is no obvious release of radium from the adsorbed hydrated manganese hydroxide complex sludge; (3) The current experiments show that hydrated manganese hydroxide complex sludge has a very good re-adsorption ability for removal of radium from uranium effluent. Some experimental parameters have been measured. (author)

Root canal treatment of pulpless immature teeth using calcium hydroxide paste. Roentgenographic study

International Nuclear Information System (INIS)

Leite, R.M.G.V.; Abbud, R.

1986-01-01

Calcium hydroxide paste was used as a temporary dressing and the renewal was done each three months in the root treatment of immature teeth with open apex and necrotic pulps. Clinical and radiographic controls were made to observe foraminal closure. After that, the root canals were filled, employing the conventional technique with gutta-percha cones and zinc oxide eugenol cements. The calcium hydroxide paste was applied in the apical region before the root canal filling. The follow-up was done periodically and the cases have more than two years of control. (author) [pt

Study of samarium modified lead zirconate titanate and nickel zinc ferrite composite system

Energy Technology Data Exchange (ETDEWEB)

Rani, Rekha [Department of Physics, SD PG College, Panipat 132103 (India); School of Physics and Materials Science, Thapar University, Patiala 147004 (India); Juneja, J.K., E-mail: jk_juneja@yahoo.com [Department of Physics, Hindu College, Sonepat 131001 (India); Singh, Sangeeta [Department of Physics, GVM Girls College, Sonepat 131001 (India); Raina, K.K. [School of Physics and Materials Science, Thapar University, Patiala 147004 (India); Prakash, Chandra [Solid State Physics Laboratory, Timarpur, Delhi 110054 (India)

2015-03-15

In the present work, composites of samarium substituted lead zirconate titanate and nickel zinc ferrite with compositional formula 0.95Pb{sub 1−3x/2} Sm{sub x}Zr{sub 0.65}Ti{sub 0.35}O{sub 3}–0.05Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} (x=0, 0.01, 0.02 and 0.03) were prepared by the conventional solid state route. X-ray diffraction analysis was carried out to confirm the coexistence of individual phases. Microstructural study was done by using scanning electron microscope. Dielectric constant and loss were studied as a function of temperature and frequency. To study ferroelectric and magnetic properties of the composite samples, corresponding P–E and M–H hysteresis loops were recorded. Change in magnetic properties of electrically poled composite sample (x=0.02) was studied to confirm the magnetoelectric (ME) coupling. ME coefficient (dE/dH) of the samples (x=0 and 0.02) was measured as a function of DC magnetic field. - Highlights: • We are reporting the effect of Sm substitution on PZT–NiZn ferrite composites. • Observation of both P–E and M–H loops confirms ferroelectric and magnetic ordering. • With Sm substitution, significant improvement in properties was observed. • Increase in magnetization for electrically poled sample is evidence of ME coupling. • Electric polarization is generated by applying magnetic field.

Inhibition of Apical Root Resorption by Calcium Hydroxide During Orthodontic Treatment: A Case Report

OpenAIRE

Pacheco, Cinthia Mara da Fonseca; Pacheco, Daniela da Fonseca; Motta, Patrícia Gonçalves da

2016-01-01

Apical root resorption is a common outcome of orthodontic treatment. The present article reports a case of absence of apical root resorption in a left maxillary lateral incisor filled with calcium hydroxide paste throughout orthodontic movement. After orthodontic treatment was completed the tooth was subsequently obturatedwith gutta-percha and the patient followed for 18 months. The presence of a periapical lesion and the properties of calcium hydroxide as a root resorption inhibitor were dec...

Calcium hydroxide induced apexification with apical root development: a clinical case report.

Science.gov (United States)

Soares, J; Santos, S; César, C; Silva, P; Sá, M; Silveira, F; Nunes, E

2008-08-01

To report the induction of apical root development by calcium hydroxide in teeth with pulp necrosis and periapical radiolucency. A 10-year-old male patient was admitted to the clinic complaining of an intense pain and oedema on the anterior facial region, compatible with an acute dentoalveolar abscess. There was a previous history of dental trauma; only tooth 11 was negative to pulp sensitivity tests. Radiographically, tooth 11 exhibited incomplete root formation, characterized by a wide root canal, thin and fragile dentinal walls, and an extensive, divergent foraminal opening associated with an apical radiolucency. The first appointment focused on urgent local and systemic treatment. Apexification treatment commenced at the second session after 7 days, by means of chemo-mechanical debridement throughout the entire root canal, using K-files and irrigation with a 2.5% sodium hypochlorite solution. Subsequently, a calcium hydroxide paste was applied and changed four times over 8 months, when radiographic examination revealed complete closure of the foraminal opening, resulting in resolution of the periapical radiolucency and associated with 5 mm of additional root development. The root canal was filled by thermomechanical compaction of gutta-percha and sealer. A 3-year follow-up revealed normal periapical tissues and the absence of symptoms. * In young patients, dental trauma may cause pulp necrosis and arrest of root formation. * Under certain circumstances, chemo-mechanical debridement, including the use of a calcium hydroxide paste, is a valid alternative to mineral trioxide aggregate and or surgery for root-end closure. * In teeth with incompletely formed roots associated with periapical lesions, calcium hydroxide can induce periapical repair through the closure of the foramen and apical root development.

Production of zeolite A come from rio Capim Kaolin: Study on recycle of sodium hydroxide solution

International Nuclear Information System (INIS)

Moraes, C.G.; Rodrigues, E.C.; Rocha Junior, C.A.F.; Macedo, E.N.; Neves, R.F.

2011-01-01

The kaolin processing industry is an important economic sector in the State of Para, but produces huge amounts of wastes composed essentially of kaolinite. The production processes of zeolites typically use sodium hydroxide in excess, are discarded. So the objective is the development process for production of zeolite A which allows the reuse of the solution of sodium hydroxide used in excess through your recycling. Presents the results of XRD, SEM of the zeolites produced in five consecutive cycles performed at a temperature of 110°C/24h as a source of sodium hydroxide solution of sodium 5 M, using a molar ratio of Si/Al = 1 and Na/Al = 1,26. (author)

Evaluation of barium hydroxide treatment efficacy on a dolomitic marble.

Science.gov (United States)

Toniolo, L; Colombo, C; Realini, M; Peraio, A; Positano, M

2001-01-01

The Arch of Peace, by Luigi Cagnola, is one of the most famous neoclassical monuments in Milan. It has been subjected to conservative intervention in 1998. In the present paper the efficacy of the consolidation by means of barium hydroxide has been evaluated. The stone material showed severe degradation phenomena as: erosion, pulverisation, exfoliation. The analytical data acquired through X-ray diffraction (XRD), infrared spectrophotometry (FTIR) and scanning electron microscopy (SEM-EDX), allowed to compare the conditions of stone before and after the treatment with barium hydroxide. The presence of barium has been put in evidence mainly on the surface as barium sulphate, whereas barium is only sporadically present within the thickness of the decayed material. The treatment was judged not satisfying and its inefficacy is, most probably, due to a not suitable cleaning procedure carried out before the consolidation.

Al-substituted {alpha}-cobalt hydroxide synthesized by potentiostatic deposition method as an electrode material for redox-supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Gupta, Vinay [Art, Science and Technology Center for Cooperative Research, Kyushu University, Kasuga-shi, Fukuoka 816-8580 (Japan); Japan Science and Technology Agency, Kawaguchi-shi, Saitama 332-0012 (Japan); Gupta, Shubhra; Miura, Norio [Art, Science and Technology Center for Cooperative Research, Kyushu University, Kasuga-shi, Fukuoka 816-8580 (Japan)

2008-03-01

Al-substituted {alpha}-cobalt hydroxide was prepared by a potentiostatic deposition process at -1.0 V (vs. Ag/AgCl) onto stainless steel electrodes by using a mixed aqueous solution of cobalt nitrate and aluminum nitrate. Their structure and surface morphology were studied by using X-ray diffraction analysis, energy dispersive X-ray spectroscopy and scanning electron microscopy. The SEM images showed changes in the nanostructure of {alpha}-cobalt hydroxide by the addition of Al. Galvanostatic charge-discharge curves showed a drastic improvement in the capacitive characteristics of {alpha}-cobalt hydroxide, with a specific energy increase from 11.3 to 18.7 Wh kg{sup -1} by the substitution of just 8 at.% Al, and a specific capacitance of 843 F g{sup -1} between 0 and 0.4 V. The cycle stability data suggest no significant changes in the discharge characteristics of {alpha}-cobalt hydroxide by the addition of Al. (author)

Fabrication of nickel-foam-supported layered zinc-cobalt hydroxide nanoflakes for high electrochemical performance in supercapacitors.

Science.gov (United States)

Yuan, Peng; Zhang, Ning; Zhang, Dan; Liu, Tao; Chen, Limiao; Liu, Xiaohe; Ma, Renzhi; Qiu, Guanzhou

2014-10-04

Nickel foam supported Zn-Co hydroxide nanoflakes were fabricated by a facile solvothermal method. Benefited from the unique structure of Zn-Co hydroxide nanoflakes on a nickel foam substrate, the as prepared materials exhibited an excellent specific capacitance of 901 F g(-1) at 5 A g(-1) and remarkable cycling stability as electrode materials in supercapacitors.

Retention capacity of samarium (III) in zircon for it possible use in retaining walls for confinement of nuclear residues; Capacidad de retencion de samario (III) en circon para su posible uso en barreras de contencion para confinamiento de residuos nucleares

Energy Technology Data Exchange (ETDEWEB)

Garcia G, N

2006-07-01

Mexico, as country that produces part of its electric power by nuclear means, should put special emphasis in the development of technologies guided to the sure and long term confinement of the high level nuclear residuals. This work studies the capacity that has the natural zircon to retain to the samarium (III) in solution, by what due, firstly, to characterize the zircon for technical instrumental to determine the purity and characteristic of the mineral in study. The instrumental techniques that were used to carry out the physicochemical characterization were the neutron activation analysis (NAA), the infrared spectroscopy (IS), the thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), semiquantitative analysis, dispersive energy spectroscopy (EDS), X-ray diffraction (XRD) and luminescence technique. The characterization of the surface properties carries out by means of the determination of the surface area using the BET multipoint technique, acidity constants, hydration time, the determination of the point of null charge (pH{sub PCN}) and density of surface sites (D{sub s}). The luminescence techniques were useful to determine the optimal point hydration of the zircon and for the quantification of the samarium, for that here intends the development of both analysis techniques. With the adjustment of the titration curves in the FITEQL 4 package the constants of surface acidity in the solid/liquid interface were determined. To the finish of this study it was corroborated that the zircon is a mineral that presents appropriate characteristics to be proposed as a contention barrier for the deep geologic confinement. With regard to the study of adsorption that one carries out the samarium retention it is superior to 90% under the described conditions. This investigation could also be applicable in the confinement of dangerous industrial residuals. (Author)

Anticorrosive magnesium hydroxide coating on AZ31 magnesium alloy by hydrothermal method

International Nuclear Information System (INIS)

Zhu Yanying; Wu Guangming; Xing Guangjian; Li Donglin; Zhao Qing; Zhang Yunhong

2009-01-01

Magnesium alloys are potential biodegradable biomaterials in orthopedic surgery. However, the rapid degradation rate has limited their application in biomedical field. A great deal of studies have been done to improve the resistance of magnesium alloys. In this article, An anticorrosive magnesium hydroxide coating with a thickness of approximately 100μm was formed on an AZ31 magnesium alloy by hydrothermal method. The morphology of the coatings were observed by an optical microscope and SEM. And the samples were soaked in hank's solution (37 deg. C) to investigate the corrosion resistance. Magnesium alloy AZ31 with magnesium hydroxide coatings present superior corrosion resistance than untreated samples.

A facile mechanochemical approach to synthesize Zn-Al layered double hydroxide

Energy Technology Data Exchange (ETDEWEB)

Qu, Jun, E-mail: forsjun@whut.edu.cn [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); He, Xiaoman; Chen, Min; Huang, Pengwu [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); Zhang, Qiwu, E-mail: zhangqw@whut.edu.cn [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); Liu, Xinzhong [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350118 (China)

2017-06-15

In this study, a mechanochemical route to synthesize Zn-Al layered double hydroxide (LDH) was introduced, in which Zn basic carbonate and Al hydroxide were first dry milled into an activated state and then agitated in water to obtain the final products. The as-prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Thermogravimetry (TG) and Scanning electron microscopy (SEM). The products possessed a high crystallinity of Zn–Al LDH phase without any other impurities, proving a facile and effective preparation of Zn–Al LDH by using non-heating mechanochemical approach. - Highlights: • A non-heating mechanochemical route to synthesize Zn-Al LDH. • The products possessed high crystalline Zn-Al LDH phase. • No emission of other impurities or wastewater.

Hollow nickel-aluminium-manganese layered triple hydroxide nanospheres with tunable architecture for supercapacitor application

International Nuclear Information System (INIS)

Chandrasekaran, Nivedhini Iswarya; Muthukumar, Harshiny; Sekar, Aiswarya Devi; Manickam, Matheswaran

2017-01-01

Hollow triple layered Ni-Al-Mn hydroxide nanocomposite is a promising electrode material with high capacitance value. Moreover, the material provides a high energy density with good cycling stability. Here we demonstrate the facile method for preparation of hollow layered triple hydroxide material in a combination of Nickel, Aluminium and Manganese with high surface area and mesoporous nature. Owing to its high electrode area and fast electron-ion transfer nature, the hollow Ni-Al-Mn hydroxide exhibits the high capacitance of 1756 F/g at 4 A/g and retains its capacitance value upto 89.5% of initial values after 4000 cycles. Additionally, it provides a higher energy density of 239.0795 Wh/kg at a power density of 1980 W/kg. HLTH of Ni-Al-Mn nanocomposite provides a better capacitance effect. Finally, this material provides a general approach for designing supercapacitor with tunable nanostructure and enhanced supercapacitor behaviour has a large application in energy storage and conversion devices. - Highlights: • An approach to acquire a hollow Ni-Al-Mn layered triple hydroxide is presented. • HLTH shows a large surface area suitable for electrochemical performance. • Exhibits high energy density of 239.07 Wh/kg at a power density of 1980 W/kg. • Recorded specific capacitance of 1756 F/g at current density 4 A/g. • HLTH retains 89.5% of initial capacitance values after 4000 cycles.

Hollow nickel-aluminium-manganese layered triple hydroxide nanospheres with tunable architecture for supercapacitor application

Energy Technology Data Exchange (ETDEWEB)

Chandrasekaran, Nivedhini Iswarya; Muthukumar, Harshiny; Sekar, Aiswarya Devi; Manickam, Matheswaran, E-mail: math.chem95@gmail.com

2017-07-01

Hollow triple layered Ni-Al-Mn hydroxide nanocomposite is a promising electrode material with high capacitance value. Moreover, the material provides a high energy density with good cycling stability. Here we demonstrate the facile method for preparation of hollow layered triple hydroxide material in a combination of Nickel, Aluminium and Manganese with high surface area and mesoporous nature. Owing to its high electrode area and fast electron-ion transfer nature, the hollow Ni-Al-Mn hydroxide exhibits the high capacitance of 1756 F/g at 4 A/g and retains its capacitance value upto 89.5% of initial values after 4000 cycles. Additionally, it provides a higher energy density of 239.0795 Wh/kg at a power density of 1980 W/kg. HLTH of Ni-Al-Mn nanocomposite provides a better capacitance effect. Finally, this material provides a general approach for designing supercapacitor with tunable nanostructure and enhanced supercapacitor behaviour has a large application in energy storage and conversion devices. - Highlights: • An approach to acquire a hollow Ni-Al-Mn layered triple hydroxide is presented. • HLTH shows a large surface area suitable for electrochemical performance. • Exhibits high energy density of 239.07 Wh/kg at a power density of 1980 W/kg. • Recorded specific capacitance of 1756 F/g at current density 4 A/g. • HLTH retains 89.5% of initial capacitance values after 4000 cycles.

Protective Activity of the Mixtures of Pine Oil and Copper Hydroxide against Bacterial Spot and Anthracnose on Red Pepper

Directory of Open Access Journals (Sweden)

Jae-Woo Soh

2014-09-01

Full Text Available This research was performed to examine the protective activities of the mixtures of pine oil and copper hydroxide against bacterial spot and anthracnose on pepper plants. As for bacterial spot, the treatment of pine oil alone displayed high disease incidence (59.6% and low protective effect (28.9%. In comparison, the treatments of mixtures and copper hydroxide alone showed protective activities of 66.8-76.1%. The mixture of pine oil and copper hydroxide (4:1 suppressed the most effectively bacterial spot on pepper. On the other hand, the mixture of pine oil and copper hydroxide (4:1 also showed the strongest protective effect against pepper anthracnose among the 4 treatments tested; its disease incidence and disease control value were 49.8% and 41.7%, respectively. The other treatments showed low protective activities with control values of 7.4-17.1%. These results suggested that the mixture of pine oil and copper hydroxide (4:1 can be used for the environmental-friendly disease control of bacterial spot and anthracnose on pepper.

REGIOSELECTIVE REACTIONS OF 3-ALKYL-1-PHENYL-2-PYRAZOLIN-5-ONES WITH ACYL HALIDES IN THE PRECENCE OF NONOSIZED MAGNESIUM HYDROXIDE AS A HIGHLY EFFECTIVE HETEROGENOUS BASE CATALYST Regioselektive Reaktionen von 3-Alkyl-1-PHENYL-2-pyrazolin-5-ONES Mit Acylhalogeniden IN DER PRECENCE DER NONOSIZED MAGNESIUM HYDROXIDE als hochwirksame heterogene BASE CATALYST

OpenAIRE

Hassan Sheibani and Bahman Massomi Nejad

2012-01-01

4-Acyl-3-alkyl-1-phenyl-2-pyrazolin-5-one derivatives were prepared by the regioselective acylation of 3-alkyl-1-phenyl-2-pyrazolin-5-ones in the presence of base catalysts such as calcium hydroxide [Ca(OH)2], magnesium hydroxide [Mg(OH)2] and nanosized magnesium hydroxide. In the presence of nanosized magnesium hydroxide, excellent yields of products were obtained and reaction times were significantly reduced.

Ferrites Ni{sub 0,5}Zn{sub 0,5}Fe{sub 2}O{sub 4} doped with samarium: structural analysis, morphological and electromagnetic; Ferritas Ni{sub 0,5}Zn{sub 0,5}Fe{sub 2}O{sub 4} dopada com samario: analise estrutural, morfologica e eletromagnetica

Energy Technology Data Exchange (ETDEWEB)

Costa, A.C.F.M.; Diniz, A.P., E-mail: anacristina@dema.ufcg.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academinca de Engenharia de Materiais; Viana, K.M.S. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, PE (Brazil). Escola de Ciencias e Tecnologia; Cornejo, D.R. [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Fisica; Kiminami, R.H.G.A. [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Departamento de Engenharia de Materiais

2010-07-01

This paper proposes to investigate the sintering at 1200 deg C/2h of Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2-x}Sm{sub x}O{sub 4} ferrite doped with 0.05; 0.075 e 0.1 mol of Sm synthesized by combustion reaction to evaluate the performance materials as absorbers of electromagnetic radiation. The influence of the concentration of samarium on the structure, morphology and electromagnetic properties of ferrites was studied. The resulting samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), magnetic measurements and reflectivity measurements in the frequency range between 8-12 GHz. The results showed that increasing the concentration of samarium caused a decrease in particle size of the samples, encouraging, therefore, to obtain materials with better values of magnetization and reflectivity, allowing for use as absorbers in narrow-band frequency between 9-10 GHz. (author)

Application of sorption method on hydroxides for purification of some reactive from iron(III) markings

International Nuclear Information System (INIS)

Rakhmonberdiev, A.D.; Khamidov, B.O.

1986-01-01

The method of purification of solutions of citric acid, tartaric acid and their salts, potassium hydroxide, potassium nitrate and chloride, sodium perchlorate from iron (III) impurities by means of sorption method on zirconium hydroxide is elaborated. The control of iron(III) content in solutions is conducted by inversion voltammetry method with mercury-graphite electrode. It is defined that complete sorption of iron (III) ions achieves at ph =4÷14.

Ion Recognition Approach to Volume Reduction of Alkaline Tank Waste by Separation and Recycle of Sodium Hydroxide and Sodium Nitrate

International Nuclear Information System (INIS)

Moyer, Bruce A.; Marchand, Alan P.; Bonnesen, Peter V.; Bryan, Jeffrey C.; Haverlock, Tamara J.

2004-01-01

This research was intended to provide the scientific foundation upon which the feasibility of liquid-liquid extraction chemistry for bulk reduction of the volume of high-activity tank waste can be evaluated. Primary focus has been on sodium hydroxide separation, with potential Hanford application. Value in sodium hydroxide separation can potentially be found in alternative flowsheets for treatment and disposal of low-activity salt waste. Additional value can be expected in recycle of sodium hydroxide for use in waste retrieval and sludge washing, whereupon additions of fresh sodium hydroxide to the waste can be avoided. Potential savings are large both because of the huge cost of vitrification of the low-activity waste stream and because volume reduction of high-activity wastes could obviate construction of costly new tanks. Toward these ends, the conceptual development begun in the original proposal was extended with the formulation of eight fundamental approaches that could be undertaken for extraction of sodium hydroxide

The effect of calcium hydroxide treatment on the nutritive and feeding value of Albizia procera for growing goats

Energy Technology Data Exchange (ETDEWEB)

Alam, M.R. [Department of Animal Science, Bangladesh Agricultural University, Mymensingh (Bangladesh)]. E-mail: mralam@royalten.net.bd; Kabir, A.K.M.A.; Amin, M.R. [Department of Animal Science, Bangladesh Agricultural University, Mymensingh (Bangladesh); McNeill, D.M. [Faculty of Veterinary Science, University of Sydney, Camden, NSW (Australia)

2005-08-19

Albizia procera (Albizia) is widely planted in Bangladesh for timber and the leaves are also used as forage. In the dry season the leaves are less palatable than in the wet season and this may be a consequence of an excessive content of tannin. Albizia foliage was collected in the wet (June) and dry (January) seasons from six agro-ecological zones across Bangladesh and chemical composition, for tannins in particular, was determined. Variation in the tannin content across the six zones proved to be minimal. However, the concentration of tannins was almost two-fold higher in the dry compared to the wet season. To assess the potential for deactivating the tannins in Albizia so as to improve its nutritive value, leaves were treated with alkali (either calcium hydroxide or potassium carbonate) or polyethylene glycol (PEG). Alkali treatment reduced the concentrations of extractable tannin by as much as 92%. The ability of calcium hydroxide to deactivate tannin was then tested in vivo. Young goats, fed a basal diet of hay and wheat bran, were allocated to 4 equal groups (n = 4 per group) and supplemented with fresh Albizia foliage (at 300 g/kg of the diet) that was either untreated, or treated with either PEG, calcium hydroxide or calcium hydroxide + PEG. The supplements were fed daily for 9 weeks to allow the effects of chemical treatment on intake and growth rate to be defined. In vivo digestibility, nitrogen (N) balance, and microbial N supply were measured over the 5th week. Intakes of feed dry matter (DM) and the digestibility of DM were similar across treatments (mean intake 32 g/(kg LW day), mean DM digestibility 0.63). However, both the PEG and the PEG + calcium hydroxide treatments, compared to the control and calcium hydroxide only treatments, increased N digestibility (0.72, 0.70 versus 0.60, 0.61), N retention (0.43, 0.48 mg N/mg versus 0.26, 0.27 mg N/mg N intake), and microbial N supply (23.7, 21.4 g/day versus 14.2, 12.4 g/day). These increases translated

The effect of calcium hydroxide treatment on the nutritive and feeding value of Albizia procera for growing goats

International Nuclear Information System (INIS)

Alam, M.R.; Kabir, A.K.M.A.; Amin, M.R.; McNeill, D.M.

2005-01-01

Albizia procera (Albizia) is widely planted in Bangladesh for timber and the leaves are also used as forage. In the dry season the leaves are less palatable than in the wet season and this may be a consequence of an excessive content of tannin. Albizia foliage was collected in the wet (June) and dry (January) seasons from six agro-ecological zones across Bangladesh and chemical composition, for tannins in particular, was determined. Variation in the tannin content across the six zones proved to be minimal. However, the concentration of tannins was almost two-fold higher in the dry compared to the wet season. To assess the potential for deactivating the tannins in Albizia so as to improve its nutritive value, leaves were treated with alkali (either calcium hydroxide or potassium carbonate) or polyethylene glycol (PEG). Alkali treatment reduced the concentrations of extractable tannin by as much as 92%. The ability of calcium hydroxide to deactivate tannin was then tested in vivo. Young goats, fed a basal diet of hay and wheat bran, were allocated to 4 equal groups (n = 4 per group) and supplemented with fresh Albizia foliage (at 300 g/kg of the diet) that was either untreated, or treated with either PEG, calcium hydroxide or calcium hydroxide + PEG. The supplements were fed daily for 9 weeks to allow the effects of chemical treatment on intake and growth rate to be defined. In vivo digestibility, nitrogen (N) balance, and microbial N supply were measured over the 5th week. Intakes of feed dry matter (DM) and the digestibility of DM were similar across treatments (mean intake 32 g/(kg LW day), mean DM digestibility 0.63). However, both the PEG and the PEG + calcium hydroxide treatments, compared to the control and calcium hydroxide only treatments, increased N digestibility (0.72, 0.70 versus 0.60, 0.61), N retention (0.43, 0.48 mg N/mg versus 0.26, 0.27 mg N/mg N intake), and microbial N supply (23.7, 21.4 g/day versus 14.2, 12.4 g/day). These increases translated

Uptake of Au(III) Ions by Aluminum Hydroxide and Their Spontaneous Reduction to Elemental Gold (Au(0)).

Science.gov (United States)

Yokoyama; Matsukado; Uchida; Motomura; Watanabe; Izawa

2001-01-01

The behavior of AuCl(4)(-) ions during the formation of aluminum hydroxide at pH 6 was examined. With an increase in NaCl concentration, the content of gold taken up by aluminum hydroxide decreased, suggesting that chloro-hydroxy complexes of Au(III) ion were taken up due to the formation of Al-O-Au bonds. It was found unexpectedly that the Au(III) ions taken up were spontaneously reduced to elemental gold without addition of a specific reducing reagent and then colloidal gold particles were formed. The mechanisms for the uptake of Au(III) ions by aluminum hydroxide and for their spontaneous reduction are discussed. Copyright 2001 Academic Press.

Comparison Of Efficacy Of 10% Potassium Hydroxide Solution Versus Cryotherapy In Treatment Of Molluscum Contagiosum.

Science.gov (United States)

Qureshi, Asfandyar; Zeb, Mahwish; Jalal-Ud-Din, Mir; Sheikh, Zafar Iqbal; Alam, Muhammad Adeel; Anwar, Syed Abbas

2016-01-01

Different topical therapies are being used for treating molluscum contagiosum. Potassium hydroxide in varying solution strengths with irritant reaction on the skin can help in eliminating the infection. It is cheap, easily available, can be easily applied at home, with good safety profile and cost effectiveness. This study was conducted to compare the efficacy of 10% potassium hydroxide solution versus cryotherapy in treating molluscum contagiosum. This study was a Randomized control trial conducted in the Department of dermatology, Military hospital Rawalpindi. Study included 120 randomly selected patients with molluscum contagiosum divided equally into two groups. Group A were treated with 10% potassium hydroxide aqueous solution applied daily to the lesions twice daily for 6 weeks while Group B received weekly cryotherapy with liquid nitrogen. The status of lesions was documented weekly for 6 weeks. Of the 120 patients enrolled, 67 (55.8%) were male and 53 (44.2%) were female. Mean age of patients was 20.53(±8.17) years. At base line Molluscum contagiosum lesion ranged from minimum of 2 lesions to maximum of 26 lesions with a mean of 8.95 (SD ±4.45) lesions. Of 120 patients, complete clearance was observed in 98(81.6%) of patients, 48(80%) patients had lesion clearance in Group A and 50 (83.3%) patients had lesion clearance was observed in Group B. No statistical significance was observed in the lesion clearance between the two groups (p-0.63). The efficacy of 10% potassium hydroxide solution and cryotherapy is statistically same over 6 weeks of treatment. Thus less expensive, easily available and cosmetically more acceptable potassium hydroxide solution can be used instead of cryotherapy in treating molluscum contagiosum.

Preparation and characterization of poly(glycidyl methacrylate) grafted from magnesium hydroxide particles via SI-ATRP

International Nuclear Information System (INIS)

Liu Jianhui; Feng Na; Chang Suqin; Kang Hongliang

2012-01-01

In order to improve the compatibility of magnesium hydroxide particles [Mg(OH) 2 ] and polymer matrix, poly(glycidyl methacrylate) (PGMA) grafted from magnesium hydroxide particles were synthesized via surface-initiated atom transfer radical polymerization (SI-ATRP). In this work, two approaches for the immobilization of ATRP initiator on the magnesium hydroxide particles surface were compared and selected. The density of initiator was significantly increased by the method of introducing more hydroxyl groups via ATRP of 2-hydroxyethyl methacrylate (HEMA) on the surface. The percentage of bromine atom for the initiator-functionalized magnesium hydroxide particles [Mg(OH) 2 -g-PHEMA-Br] reached to 1.75%, compared to 0.48% for Mg(OH) 2 -Br determined by XPS analysis. The surface-initiated ATRP of glycidyl methacrylate (GMA) can be conducted in a controlled manner, as revealed by the linear kinetic plot, linear increase of number average molecular weight (M n ) with monomer conversions, and the relatively narrow molecular weight distributions (M w /M n ∼ 1.4) of PGMA chains. The percentage of grafting PG (%) and the thickness of the grafted polymer layer increased with the increasing of polymerization time and reached to 116.6% and 197.6 nm after 300 min respectively. As for the polymerization with different initial monomer concentration, the number average molecular weights (M n ) and weight average molecular weights (M w ) of PGMA increased with the increasing of initial monomer concentration. TGA indicated that the initial decomposition temperature of Mg(OH) 2 -g-PHEMA-PGMA composite particles (253 °C) was much lower than that of unmodified magnesium hydroxide particles (337 °C).

Preparation and characterization of poly(glycidyl methacrylate) grafted from magnesium hydroxide particles via SI-ATRP

Energy Technology Data Exchange (ETDEWEB)

Liu Jianhui [School of Textile and Materials Engineering, Dalian Polytechnic University, Dalian 116034 (China); Feng Na, E-mail: fengna12@163.com [School of Textile and Materials Engineering, Dalian Polytechnic University, Dalian 116034 (China); Chang Suqin [China Leather and Footwear Industry Research Institute, Beijing 100015 (China); Kang Hongliang [State Key Laboratory of Polymer Physics and Chemistry, Joint Laboratory of Polymer Science and Material, Beijing National Laboratory for Molecular Sciences (BNLMS), Institute of Chemistry, Chinese Academy of Sciences, Beijing 100080 (China)

2012-06-01

In order to improve the compatibility of magnesium hydroxide particles [Mg(OH){sub 2}] and polymer matrix, poly(glycidyl methacrylate) (PGMA) grafted from magnesium hydroxide particles were synthesized via surface-initiated atom transfer radical polymerization (SI-ATRP). In this work, two approaches for the immobilization of ATRP initiator on the magnesium hydroxide particles surface were compared and selected. The density of initiator was significantly increased by the method of introducing more hydroxyl groups via ATRP of 2-hydroxyethyl methacrylate (HEMA) on the surface. The percentage of bromine atom for the initiator-functionalized magnesium hydroxide particles [Mg(OH){sub 2}-g-PHEMA-Br] reached to 1.75%, compared to 0.48% for Mg(OH){sub 2}-Br determined by XPS analysis. The surface-initiated ATRP of glycidyl methacrylate (GMA) can be conducted in a controlled manner, as revealed by the linear kinetic plot, linear increase of number average molecular weight (M{sub n}) with monomer conversions, and the relatively narrow molecular weight distributions (M{sub w}/M{sub n} {approx} 1.4) of PGMA chains. The percentage of grafting PG (%) and the thickness of the grafted polymer layer increased with the increasing of polymerization time and reached to 116.6% and 197.6 nm after 300 min respectively. As for the polymerization with different initial monomer concentration, the number average molecular weights (M{sub n}) and weight average molecular weights (M{sub w}) of PGMA increased with the increasing of initial monomer concentration. TGA indicated that the initial decomposition temperature of Mg(OH){sub 2}-g-PHEMA-PGMA composite particles (253 Degree-Sign C) was much lower than that of unmodified magnesium hydroxide particles (337 Degree-Sign C).

Separation of valent forms of chromium (3) and chromium (6) by coprecipitation with iron (3) hydroxide

International Nuclear Information System (INIS)

Nazirmadov, B.; Khamidov, B.O.; Egorova, L.A.

1988-01-01

Soption 9.62x10 -5 mol/l of 51 Cr radioactive isotope in oxidation states 3 and 6 by iron(3) hydroxide in 1 mol/l of KNO 3 and KCl depending on pH medium is investigated. The region of practically total concentration of Cr(3) and Cr(6 + ) (pH=3-6.5) is determined. The results of spectrophotometric investigations, calculational data on distribution of hydroxocation forms of chromium (3) and of chromium (6) anions and sorption by iron (3) hydroxide permit to characterize sorption of chromium forms in different stages of oxidation. The methods of chromium (3) and chromium (6) separation by coprecipitation of iron (3) hydroxide and their precipitation from it is developed on the above foundation

Sorptive stabilization of organic matter by amorphous Al hydroxide

NARCIS (Netherlands)

Schneider, M.P.W.; Scheel, T.; Mikutta, R.; van Hees, P.; Kaiser, K.; Kalbitz, K.

2010-01-01

Amorphous Al hydroxides (am-Al(OH)(3)) strongly sorb and by this means likely protect dissolved organic matter (OM) against microbial decay in soils. We carried out batch sorption experiments (pH 4.5; 40 mg organic C L-1) with OM extracted from organic horizons under a Norway spruce and a European

Effects of increasing doses of samarium-153-ethylenediaminetetramethylene phosphonate on axial and appendicular skeletal growth in juvenile rabbits

International Nuclear Information System (INIS)

Essman, Stephanie C.; Lewis, Michael R.; Fox, Derek B.

2008-01-01

Introduction: Targeted radiotherapy using samarium-153-ethylenediaminetetramethylene phosphonate ( 153 Sm-EDTMP) is currently under investigation for treatment of osteosarcoma. Osteosarcoma often occurs in children, and previous studies on a juvenile rabbit model demonstrated that clinically significant damage to developing physeal cartilage may occur as a result of systemic 153 Sm-EDTMP therapy. The aim of this study was to evaluate the late effects of 153 Sm-EDTMP on skeletal structures during growth to maturity and to determine if there is a dose response of 153 Sm-EDTMP on growth of long bones. Methods: Female 8-week-old New Zealand white rabbits were divided into three treatment groups plus controls. Each rabbit was intravenously administered a predetermined dose of 153 Sm-EDTMP. Multiple bones of each rabbit were radiographed every 2 months until physeal closure, with subsequent measurements made to assess for abbreviated bone growth. Statistical analyses were performed to determine the differences in bone length between groups, with significance set at P 153 Sm-EDTMP. Further investigation regarding the effects of bone-seeking radiopharmaceuticals on bone growth and physeal cartilage is warranted

A facile one-pot synthesis of ruthenium hydroxide nanoparticles on magnetic silica: Aqueous hydration of nitriles to amides

Science.gov (United States)

One-pot synthesis of ruthenium hydroxide nanoparticles on magnetic silica is described which involve the in situ generation of magnetic silica (Fe3O4@ SiO2) and ruthenium hydroxide immobilization; the hydration of nitriles occurs in high yield and excellent selectivity using this...

Cadmium-Aluminum Layered Double Hydroxide Microspheres for Photocatalytic CO2Reduction

KAUST Repository

Saliba, Daniel

2016-03-30

We report the synthesis of cadmium-aluminum layered double hydroxide (CdAl LDH) using the reaction-diffusion framework. As the hydroxide anions diffuse into an agar gel matrix containing the mixture of aluminum and cadmium salts at a given ratio, they react to give the LDH. The LDH self-assembles inside the pores of the gel matrix into a unique spherical-porous shaped microstructure. The internal and external morphologies of the particles are studied by electron microscopy and tomography revealing interconnected channels and a high surface area. This material is shown to exhibit a promising performance in the photoreduction of carbon dioxide using solar light. Moreover, the palladium-decorated version shows a significant improvement in its reduction potential at room temperature. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cadmium-Aluminum Layered Double Hydroxide Microspheres for Photocatalytic CO2Reduction

KAUST Repository

Saliba, Daniel; Ezzeddine, Alaa; Sougrat, Rachid; Khashab, Niveen M.; Hmadeh, Mohamad; Al-Ghoul, Mazen

2016-01-01

We report the synthesis of cadmium-aluminum layered double hydroxide (CdAl LDH) using the reaction-diffusion framework. As the hydroxide anions diffuse into an agar gel matrix containing the mixture of aluminum and cadmium salts at a given ratio, they react to give the LDH. The LDH self-assembles inside the pores of the gel matrix into a unique spherical-porous shaped microstructure. The internal and external morphologies of the particles are studied by electron microscopy and tomography revealing interconnected channels and a high surface area. This material is shown to exhibit a promising performance in the photoreduction of carbon dioxide using solar light. Moreover, the palladium-decorated version shows a significant improvement in its reduction potential at room temperature. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cadmium-Aluminum Layered Double Hydroxide Microspheres for Photocatalytic CO2 Reduction.

Science.gov (United States)

Saliba, Daniel; Ezzeddine, Alaa; Sougrat, Rachid; Khashab, Niveen M; Hmadeh, Mohamad; Al-Ghoul, Mazen

2016-04-21

We report the synthesis of cadmium-aluminum layered double hydroxide (CdAl LDH) using the reaction-diffusion framework. As the hydroxide anions diffuse into an agar gel matrix containing the mixture of aluminum and cadmium salts at a given ratio, they react to give the LDH. The LDH self-assembles inside the pores of the gel matrix into a unique spherical-porous shaped microstructure. The internal and external morphologies of the particles are studied by electron microscopy and tomography revealing interconnected channels and a high surface area. This material is shown to exhibit a promising performance in the photoreduction of carbon dioxide using solar light. Moreover, the palladium-decorated version shows a significant improvement in its reduction potential at room temperature. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of glycoluril catalyzed by potassium hydroxide under ultrasound irradiation.

Science.gov (United States)

Li, Ji-Tai; Liu, Xiao-Ru; Sun, Ming-Xuan

2010-01-01

Synthesis of the glycolurils catalyzed by potassium hydroxide was carried out in 17-75% yield at 40 degrees C in EtOH under ultrasound irradiation. Compared to the method using stirring, the main advantage of the present procedure is milder conditions and shorter reaction time.

Effective Production of Sorbitol and Mannitol from Sugars Catalyzed by Ni Nanoparticles Supported on Aluminium Hydroxide

Directory of Open Access Journals (Sweden)

Rodiansono Rodiansono

2013-06-01

Full Text Available Effective production of hexitols (sorbitol and mannitol was achieved from sugars by means of nickel nanoparticles supported on aluminium hydroxide (NiNPs/AlOH catalyst. NiNPs/AlOH catalyst was prepared by a simple and benign environmentally procedure using less amount of sodium hydroxide. ICP-AES and XRD analyses confirmed that the NiNPs/AlOH catalysts comprised a large amount of remained aluminium hydroxide (i.e. bayerite and gibbsite. The presence of aluminium hydroxide caused a high dispersion Ni metal species. The average Ni crystallite sizes that derived from the Scherrer`s equation for former R-Ni and NiNPs/AlOH were 8.6 nm and 4.1 nm, respectively. The catalyst exhibited high activity and selectivity both hydrogenolysis of disaccharides (sucrose and cellobiose and monosaccharides (glucose, fructose, and xylose at 403 K for 24 h. The NiNPs/AlOH catalyst was found to be reusable for at least five consecutive runs without any significant loss of activity and selectivity. © 2013 BCREC UNDIP. All rights reservedReceived: 21st December 2012; Revised: 7th February 2013; Accepted: 10th February 2013[How to Cite: Rodiansono, R., Shimazu, S. (2013. Effective Production of Sorbitol and Mannitol from Sug-ars Catalyzed by Ni Nanoparticles Supported on Aluminium Hydroxide. Bulletin of Chemical Reaction Engineering & Catalysis, 8 (1: 40-46. (doi:10.9767/bcrec.8.1.4290.40-46][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.8.1.4290.40-46] | View in  |

Thermal behaviour of layered double hydroxides studied by emanation thermal analysis

Czech Academy of Sciences Publication Activity Database

Dorničák, V.; Balek, V.; Kovanda, F.; Večerníková, Eva

90-91, - (2003), s. 475-480 ISSN 1012-0394 Institutional research plan: CEZ:AV0Z4032918 Keywords : hydrotalcite * layered double hydroxides * thermal decomposition Subject RIV: CA - Inorganic Chemistry Impact factor: 0.687, year: 2003

Conductimetric and Potentiometric Titration of Some Hydroxylated Cinnamic Acids with Tetrabutylammonium Hydroxide in Non-Aqueous Media

OpenAIRE

AKTAŞ, A. Hakan; YAŞAR, Gülsüm; ALSANCAK, Güleren ÖZKAN

2001-01-01

In this study, four hydroxycinnamic acids, namely 3,4-dihydroxycinnamic acid, 4-hydroxycinnamic acid, 4-hydroxy --3- methoxycinnamic acid and 4-hydroxy-3,5-dimethoxycinnamic acid, were titrated conductimetrically and potentiometrically using triethylamine and tetrabutylammonium hydroxide in acetonitrile, 2-propanol, and pyridine solvents under a nitrogen atmosphere at 25 oC. In conductimetric titration with tetrabutylammonium hydroxide all of the compounds exhibited conventional s...

Flare-ups incidence and severity after using calcium hydroxide as intracanal dressing.

Science.gov (United States)

Ghoddusi, Jamileh; Javidi, Maryam; Zarrabi, Mohammad Hasan; Bagheri, Hossein

2006-01-01

Acute pain and swelling following endodontic treatment are a challenge for both the patient and the dentist. According to previous studies, the incidence of flare-ups increases after endodontic treatment of teeth with necrotic pulps. Calcium hydroxide is currently used as a multi-purpose drug in root canal therapy. The aim of this study was to evaluate the incidence and severity of flare-ups after treatment of pulpless teeth using calcium hydroxide as an intracanal dressing. Sixty patients with single-root necrotic teeth participated in this study. These patients were randomly divided into three groups of 20. The patients were treated in Group A in a single-visit approach, in group B with a two-visit approach without any intracanal dressing and group C with a two-visit approach using calcium hydroxide as an intracanal dressing for one week. All of the patients were followed for 72 hours after each treatment session. The information about the incidence and severity of pain and swelling was recorded in tables, using a modified Visual Analogue Scale for pain severity measurement and a scale with four degrees for measuring the severity of swelling. The data were analyzed by chi-square test and GENMODE procedure.

Evaluation of interference of calcium hydroxide-based intracanal medication in filling root canal systems.

Science.gov (United States)

Vilela, Deyla Duarte; Neto, Manoel Matos; Villela, Alexandre Mascarenhas; Pithon, Matheus Melo

2011-09-01

To evaluate the interference of the intracanal medication Calen® (SSWhite, Sao Paulo, Brazil) on the filling of simulated lateral canals. Twenty human anterior teeth were used. Before the endodontic filling procedures the access of cavity was made, and after this root canals were made in all the teeth to simulate the presence of lateral canals. After preparation, the teeth were randomly divided into two groups (n=10). In group I, the root canal system was filled directly after chemicalmechanical preparation; in group II, endodontic treatment was performed in multiple sessions, and after preparation the calcium hydroxide-based intracanal medication Calen® was inserted. After the period of 7 days, the root canals were vigorously irrigated and then they were filled. Next, the teeth were radiographed to verify the quality of the filling. The results demonstrated that the teeth treated in a single session, without calcium hydroxide medication, presented 47 canals out of 60 with radiographic evidence of filling, whereas the teeth in which intracanal medication was used, only 07 presented a radiographic image compatible with filling (p < 0.05). The use of the calcium hydroxide-based medication Calen made it difficult to obtain a hermetic filling of the root canal system. The clinical significance of this work basing on the fact that once the dentist knowing that property obliteration of calcium hydroxide can be taken care when they are used in the presence of lateral canals.

Phase transformation of aluminium hydroxide to aα- alumina prepared from different aluminium salts

International Nuclear Information System (INIS)

Masliana Muslimin; Meor Yusoff Meor Sulaiman

2006-01-01

The study intends to look at the most suitable aluminium salt to produce a single-phase a-alumina by the hydrothermal method. In the process to produce alumina from the calcination of aluminium hydroxide (Al(OH) 3 ), three different aluminium salts namely aluminium sulfate (Al 2 (SO 4) 2), aluminium nitrate (A(NO 3 ) 3 ) and aluminium chloride (AlCl 3 ) were tried. The process involved the used of NH 4 OH as the precipitating medium. Aluminium hydroxide produced from each of these salts were characterised by x-ray diffraction (XRD) technique to identity the crystalline phase. Aluminium hydroxide produced by all the different aluminium salts is present as boehmite or pseudo-boehmite phase. Aluminium hydroxide produced from Al 2 (SO) 2 , Al(NO) 3 and AlCl 3 shows the transformation of the boehmite phase to a α-alumina phase at 500 0 C. On further heating, the α-alumina continuously formed at 800 o C followed soon at 1000 o C. But for the Al(NO3) 3 salts a different phase transitions occurs on heating especially at 1000 o C. Here it was observed not a single alumina phase is presence but the presence of both α and γ--alumina phases. At 1300 o C, the single α-alumina phase was formed. The study concluded that aluminium sulphate is recommended in order to obtain a single-phase α-alumina with the required characteristics. (Author)

NICKEL HYDROXIDE FILMS IN CONTACT WITH AN ELECTROACTIVE SOLUTION. A STUDY EMPLOYING ELECTROCHEMICAL IMPEDANCE MEASUREMENTS

OpenAIRE

RICARDO TUCCERI

2018-01-01

The deactivation of nickel hydroxide films after prolonged storage times without use was studied. This study was carried out in the context of the Rotating Disc Electrode Voltammetry (RDEV) and Electrochemical Impedance Spectroscopy (EIS) when the nickel hydroxide film contacts an electroactive solution and a redox reaction occurs at the Au-Ni(OH)2|electrolyte interface. Deferasirox (4-(3,5-bis(2- hydroxyphenyl)-1,2,4-triazol-1-yl) benzoic acid) was employed as redox species in solution. Limi...

Study of Structural, Morphological and Optical Properties of Magnesium Hydroxide Nanoplates Synthesized by Precipitation Route

Directory of Open Access Journals (Sweden)

S. yousefi

2018-03-01

Full Text Available In this paper, high purity magnesium hydroxide nanoplates were successfully synthesized by using brine rich in magnesium ions as precursor and NaOH as precipitating agent without using dispersant agent in the room temoerature. The study and characterization of various properties of obtained nanopowder was carried out by X-Ray Diffraction (XRD, Field Emission Scanning Electron Microscopy (FESEM, Energy Dispersive X-ray Fluorescence Spectrometer (EDX, Fourier Transform Infrared Spectrophotometer (FTIR and Ultraviolet–visible spectroscopy (UV-Vis. The FESEM and XRD analysis results showed that magnesium hydroxide powder had nanoplates with the average crystallite size 17.1nm and no impurity; that was in agreement with the result of EDX and FTIR perfectly. Furthermore, optical characteristics of magnesium hydroxide nanoplates by UV-Vis spectroscopy showed an optical band gap of 5.5 eV. This wide band gap can be a useful innovation in optoelectronic sub-micron devices.

Studies on Thorium Adsorption Characteristics upon Activated Titanium Hydroxide Prepared from Rosetta Ilmenite Concentrate

International Nuclear Information System (INIS)

Gado, M; Zaki, S

2016-01-01

The titanium hydroxide prepared from Rosetta ilmenite concentrate has been applied for Th (IV) adsorption from its acid aqueous solutions. The prepared hydroxide is first characterized by both Fourier transform infrared (FT-IR) spectrum and thermogravimetric analysis. The relevant factors affecting the adsorption process have been studied. The obtained equilibrium data fits well with the Langmuir isotherm rather than Freundlich isotherm, while the adsorption kinetic data follow the pseudo-second order model. The different thermodynamic parameters have also been calculated and indicate that the adsorption process is spontaneous

Effect of growth parameters on spatial pattern formation of cadmium hydroxide in agar gel

International Nuclear Information System (INIS)

Palaniandavar, N.; Gnanam, F.D.; Ramasamy, P.

1986-01-01

The interrelated effects of growth parameters on spatial pattern formation of cadmium hydroxide in agar gel medium have been investigated. The main parameters are concentration of electrolytes, pH of the medium, density of the gel, the concentration of parasitic electrolyte and the concentration of additives. The pattern formation is explained on the basis of electrical double layer theory coupled with diffusion. Using Shinohara's revised coagulation concept, the flocculation value is calculated. With suitable combinations of parameter values, dendritic growth and spherulitic growth of cadmium hydroxide crystals have been observed. (author)

Beryllium. Evaluation of beryllium hydroxide industrial processes. Pt. 3

International Nuclear Information System (INIS)

Lires, O.A.; Delfino, C.A.; Botbol, J.

1991-01-01

This work continues the 'Beryllium' series. It is a historical review of different industrial processes of beryllium hydroxide obtention from beryllium ores. Flowsheats and operative parameters of five plants are provided. These plants (Degussa, Brush Beryllium Co., Beryllium Corp., Murex Ltd., SAPPI) were selected as representative samples of diverse commercial processes in different countries. (Author) [es

Rare earth and zinc layered hydroxide salts intercalated with the 2-aminobenzoate anion as organic luminescent sensitizer

International Nuclear Information System (INIS)

Cursino, Ana Cristina Trindade; Rives, Vicente; Arizaga, Gregorio Guadalupe Carbajal; Trujillano, Raquel; Wypych, Fernando

2015-01-01

Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide salts intercalated with nitrate anions were synthesized, followed by exchange with 2-aminobenzoate. The UV absorption ability was improved after intercalation/grafting in relation to that shown by the parent material. - Highlights: • Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide were synthesized. • Intercalated nitrate anions were exchanged by 2-aminobenzoate. • In all the 2-aminobenzoate containing compounds, the grafting reaction was detected. • The UV absorption ability was improved after the exchange reactions. • Rare earth hydroxide salts are potential matrixes to produce luminescent materials. - Abstract: Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide salts intercalated with nitrate anions were synthesized, followed by exchange with 2-aminobenzoate. The obtained compounds were characterized by powder X-ray diffraction (PXRD), Fourier transform infrared (FTIR) and ultraviolet visible (UV–vis) spectroscopies, fluorescence measurements and thermal analysis (TGA/DTA). The results from FTIR spectroscopy suggest a direct coordination of 2-aminobenzoate to the metal cations of the inorganic layered structure. The organic derivative products from the intercalation reactions absorb a broader range of UV-light in relation to that shown by the parent material; the photoluminescence measurements present a strong violet, blue and green luminescence under UV-light excitation for layered compounds with, Zn, Y and Tb, respectively. Rare earth hydroxide salts (RE-LHS) are potential alternative matrices for the immobilization of organic species to produce luminescent materials

Rare earth and zinc layered hydroxide salts intercalated with the 2-aminobenzoate anion as organic luminescent sensitizer

Energy Technology Data Exchange (ETDEWEB)

Cursino, Ana Cristina Trindade, E-mail: anacursino@ufpr.br [CEPESQ – Research Centre of Applied Chemistry, Department of Chemistry, Universidade Federal do Paraná – P.O. Box 19081, 81531-980 Curitiba, PR (Brazil); Rives, Vicente, E-mail: vrives@usal.es [GIR-QUESCAT – Department of Inorganic Chemistry, Universidad de Salamanca, Plaza de la Merced S/N, 37998 Salamanca (Spain); Arizaga, Gregorio Guadalupe Carbajal, E-mail: gregoriocarbajal@yahoo.com.mx [Universidad de Guadalajara, Department of Chemistry, Boulevard Marcelino García Barragán 1421, C.P. 44430 Guadalajara, Jalisco (Mexico); Trujillano, Raquel, E-mail: rakel@usal.es [GIR-QUESCAT – Department of Inorganic Chemistry, Universidad de Salamanca, Plaza de la Merced S/N, 37998 Salamanca (Spain); Wypych, Fernando, E-mail: wypych@ufpr.br [CEPESQ – Research Centre of Applied Chemistry, Department of Chemistry, Universidade Federal do Paraná – P.O. Box 19081, 81531-980 Curitiba, PR (Brazil)

2015-10-15

Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide salts intercalated with nitrate anions were synthesized, followed by exchange with 2-aminobenzoate. The UV absorption ability was improved after intercalation/grafting in relation to that shown by the parent material. - Highlights: • Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide were synthesized. • Intercalated nitrate anions were exchanged by 2-aminobenzoate. • In all the 2-aminobenzoate containing compounds, the grafting reaction was detected. • The UV absorption ability was improved after the exchange reactions. • Rare earth hydroxide salts are potential matrixes to produce luminescent materials. - Abstract: Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide salts intercalated with nitrate anions were synthesized, followed by exchange with 2-aminobenzoate. The obtained compounds were characterized by powder X-ray diffraction (PXRD), Fourier transform infrared (FTIR) and ultraviolet visible (UV–vis) spectroscopies, fluorescence measurements and thermal analysis (TGA/DTA). The results from FTIR spectroscopy suggest a direct coordination of 2-aminobenzoate to the metal cations of the inorganic layered structure. The organic derivative products from the intercalation reactions absorb a broader range of UV-light in relation to that shown by the parent material; the photoluminescence measurements present a strong violet, blue and green luminescence under UV-light excitation for layered compounds with, Zn, Y and Tb, respectively. Rare earth hydroxide salts (RE-LHS) are potential alternative matrices for the immobilization of organic species to produce luminescent materials.

Production of calcium hydroxide from the waste of Cariri stone

International Nuclear Information System (INIS)

Alves, T.M.E.; Santos, A.M.M.; Brasileiro, M.I.; Pinheiro, S.F.L.; Prado, A.C.A.

2016-01-01

The extraction of Cariri stone in the northeast is a frequent activity because of its ornamental application as well as for the construction sector. However, by this extraction, untapped waste formation grows and becomes a problem for the environment. The objective of this work is to produce calcium hydroxide, from this limestone residue, with controlled porosity, solubility and particle size. The waste was characterized with X-Ray Diffraction (XRD), X-Ray Fluorescence (XRF) and thermal analysis (TGA). The limestone was calcined at 850°C and 950°C for 45 minutes and three hours, being characterized by XRD, XRF and TGA. Once calcined, it was hydrated with 17,5g and 22g oxide to 100mL water and manually mixed for 15 and 25 minutes. The calcium hydroxides have been submitted for tests in vivo in rats and will be characterized by XRD, Scanning Electron Microscopy (SEM) and Infrared. (author)

Observation of near infrared and enhanced visible emissions from electroluminescent devices with organo samarium(III) complex

Energy Technology Data Exchange (ETDEWEB)

Chu, B [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Li, W L [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Hong, Z R [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Zang, F X [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Wei, H Z [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Wang, D Y [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Li, M T [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Lee, C S [Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Lee, S T [Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China)

2006-11-07

Samarium (dibenzoylmethanato){sub 3} bathophenanthroline (Sm(DBM){sub 3} bath) was employed as an emitting and electron transport layer in organic light emitting diodes (OLEDs), and narrow electroluminescent (EL) emissions of a Sm{sup 3+} ion were observed in the visible and near infrared (NIR) region, differing from those of the same devices with Eu{sup 3+}- or Tb{sup 3+}-complex EL devices with the same structure. The EL emissions of the Sm{sup 3+}-devices originate from transitions from {sup 4}G{sub 5/2} to the lower respective levels of Sm{sup 3+} ions. A maximum luminance of 490 cd m{sup -2} at 15 V and an EL efficiency of 0.6% at 0.17 mA cm{sup -2} were obtained in the visible region, and the improved efficiency should be attributed to introducing a transitional layer between the N,N'-diphenyl-N,N'-bis(3-methylphenyl)-1,1'-diphenyl-4,4'-diamine (TPD) film and the Sm(DBM){sub 3} bath film and the avoidance of interfacial exciplex emission in devices. Sharp emissions of Sm{sup 3+} ions in the NIR region were also observed under a lower threshold value less than 4.5 V.

The effect of CTAB on synthesis in butanol of samaria and gadolinia doped ceria - nickel oxide ceramics

International Nuclear Information System (INIS)

Arakaki, A.R.; Cunha, S.M.; Yoshito, W.K.; Ussui, V.; Lazar, D.R.R.

2011-01-01

In this work it was synthesized doped ceria and Samaria gadolinia - nickel oxide ceramics, mainly applied as anodes Fuel Cells Solid Oxide. Powders of composition Ce 0,8 (SmGd) 0,2 O 1,9 /NiO and mass ratio of 40: 60% were initially synthesized by hydroxides coprecipitation and then treated solvo thermically in butanol. Cerium samarium, gadolinium and nickel chlorides and CTAB with molar ratio metal / CTAB ranging from 1 to 3, were used as raw materials Powders were treated in butanol at 150 deg C for 16h. The powders were analyzed by X-ray diffraction, scanning electron microscopy, specific surface area for adsorption of nitrogen and particle size distribution by laser beam scattering. The ceramics were analyzed by scanning electron microscopy and density measurements by immersion technique in water. The results showed that the powders had the characteristic crystalline structures of ceria and nickel hydroxide, and high specific surface area (80 m 2 / g). The characterizations of ceramics demonstrated high chemical homogeneity and porosity values of 30%. (author)

Calcium hydroxide isotope effect in calcium isotope enrichment by ion exchange

International Nuclear Information System (INIS)

Jepson, B.E.; Shockey, G.C.

1984-01-01

The enrichment of calcium isotopes has been observed in ion-exchange chromatography with an aqueous phase of calcium hydroxide and a solid phase of sulfonic acid resin. The band front was exceedingly sharp as a result of the acid-base reaction occuring at the front of the band. Single-stage separation coefficients were found to be epsilon( 44 Ca/ 40 Ca) = 11 x 10 -4 and epsilon( 48 Ca/ 40 Ca) = 18 x 10 -4 . The maximum column separation factors achieved were 1.05 for calcium-44 and 1.09 for calcium-48 with the heavy isotopes enriching in the fluid phase. The calcium isotope effect between fully hydrated aqueous calcium ions and undissociated aqueous calcium hydroxide was estimated. For the calcium-44/40 isotope pair the separation coefficient was 13 x 10 -4 . 20 references, 2 figures

Facilitated transport in hydroxide-exchange membranes for post-combustion CO2 separation.

Science.gov (United States)

Xiong, Laj; Gu, Shuang; Jensen, Kurt O; Yan, Yushan S

2014-01-01

Hydroxide-exchange membranes are developed for facilitated transport CO2 in post-combustion flue-gas feed. First, a correlation between the basicity of fixed-site functional groups and CO2 -separation performance is discovered. This relationship is used to identify phosphonium as a promising candidate to achieve high CO2 -separation performance. Consequently, quaternary phosphonium-based hydroxide-exchange membranes are demonstrated to have a separation performance that is above the Robeson upper bound. Specifically, a CO2 permeability as high as 1090 Barrer and a CO2 /N2 selectivity as high as 275 is achieved. The high performance observed in the membranes can be attributed to the quaternary phosphonium moiety. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis and characterization of samarium-doped ZnS nanoparticles: A novel visible light responsive photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Hanifehpour, Younes, E-mail: y_hanifehpour@yu.ac.kr [School of Mechanical Engineering, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of); Soltani, Behzad; Amani-Ghadim, Ali Reza; Hedayati, Behnam [Department of Chemistry, Faculty of Basic Sciences, Azarbaijan Shahid Madani University, Tabriz (Iran, Islamic Republic of); Khomami, Bamin [Department of Chemical and Biomolecular Engineering, University of Tennessee, Knoxville, TN 37996 (United States); Joo, Sang Woo, E-mail: swjoo1@gmail.com [School of Mechanical Engineering, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of)

2016-04-15

Highlights: • Sm-doped ZnS Nanomaterials were synthesized by hydrothermal method. • The as-prepared compounds were characterized by XRD, TEM, XPS, SEM and UV techniques. • The photocatalytic effect of compounds was determined by Reactive Red 43 degradation. • The degradation of RRed 43 followed the Langmuir–Hinshelwood kinetic model. - Abstract: We prepared pure and samarium-doped ZnS (Sm{sub x}Zn{sub 1−x}S{sub 1+0.5x}) nanoparticles via hydrothermal process at 160 °C for 24 h. XRD analysis shows that the particles were well crystallized and corresponds to a cubic sphalerite phase. SEM and TEM images indicate that the sizes of the particles were in the range of 20–60 nm. The photocatalytic activity of Sm-doped ZnS nanoparticles was evaluated by monitoring the decolorization of Reactive Red 43 in aqueous solution under visible light irradiation. The color removal efficiency of Sm{sub 0.04}Zn{sub 0.96}S and pure ZnS was 95.1% and 28.7% after 120 min of treatment, respectively. Among the different amounts of dopant agent used, 4% Sm-doped ZnS nanoparticles indicated the highest decolorization. We found that the presence of inorganic ions such as Cl{sup −}, CO{sub 3}{sup 2−} and other radical scavengers such as buthanol and isopropyl alcohol reduced the decolorization efficiency.

Permanence and diffusion of borax-copper hydroxide remedial preservative applied to unseasoned pine posts : 10 year update

Science.gov (United States)

Douglas Crawford; Stan Lebow; Mike West; Bill Abbott

2005-01-01

In 1993, unseasoned pine posts were treated with groundline remedial treatment containing 3.1% copper hydroxide and 40% sodium tetraborate decahydrate (borax). The soundness of the posts was periodically evaluated using a push test. After 3.5, 6.5, and 10 years, sections were taken from two posts to determine retention of borax and copper hydroxide below ground to 36...

The importance of proper crystal-chemical and geometrical reasoning demonstrated using layered single and double hydroxides

International Nuclear Information System (INIS)

Richardson, Ian G.

2013-01-01

The importance and utility of proper crystal-chemical and geometrical reasoning in structural studies is demonstrated through the consideration of layered single and double hydroxides. New yet fundamental information is provided and it is evident that the crystal chemistry of the double hydroxide phases is much more straightforward than is apparent from the literature. Atomistic modelling techniques and Rietveld refinement of X-ray powder diffraction data are widely used but often result in crystal structures that are not realistic, presumably because the authors neglect to check the crystal-chemical plausibility of their structure. The purpose of this paper is to reinforce the importance and utility of proper crystal-chemical and geometrical reasoning in structural studies. It is achieved by using such reasoning to generate new yet fundamental information about layered double hydroxides (LDH), a large, much-studied family of compounds. LDH phases are derived from layered single hydroxides by the substitution of a fraction (x) of the divalent cations by trivalent. Equations are derived that enable calculation of x from the a parameter of the unit cell and vice versa, which can be expected to be of widespread utility as a sanity test for extant and future structure determinations and computer simulation studies. The phase at x = 0 is shown to be an α form of divalent metal hydroxide rather than the β polymorph. Crystal-chemically sensible model structures are provided for β-Zn(OH) 2 and Ni- and Mg-based carbonate LDH phases that have any trivalent cation and any value of x, including x = 0 [i.e. for α-M(OH) 2 ·mH 2 O phases

Efficacy of NiTi rotary instruments in removing calcium hydroxide dressing residues from root canal walls

Directory of Open Access Journals (Sweden)

Milton Carlos Kuga

2012-02-01

Full Text Available The aim of this study was to evaluate the efficacy of three rotary instrument systems (K3, ProTaper and Twisted File in removing calcium hydroxide residues from root canal walls. Thirty-four human mandibular incisors were instrumented with the ProTaper System up to the F2 instrument, irrigated with 2.5% NaOCl followed by 17% EDTA, and filled with a calcium hydroxide intracanal dressing. After 7 days, the calcium hydroxide dressing was removed using the following rotary instruments: G1 - NiTi size 25, 0.06 taper, of the K3 System; G2 - NiTi F2, of the ProTaper System; or G3 - NiTi size 25, 0.06 taper, of the Twisted File System. The teeth were longitudinally grooved on the buccal and lingual root surfaces, split along their long axis, and their apical and cervical canal thirds were evaluated by SEM (×1000. The images were scored and the data were statistically analyzed using the Kruskall Wallis test. None of the instruments removed the calcium hydroxide dressing completely, either in the apical or cervical thirds, and no significant differences were observed among the rotary instruments tested (p > 0.05.

Electrocatalytic performance evaluation of cobalt hydroxide and cobalt oxide thin films for oxygen evolution reaction

Science.gov (United States)

Babar, P. T.; Lokhande, A. C.; Pawar, B. S.; Gang, M. G.; Jo, Eunjin; Go, Changsik; Suryawanshi, M. P.; Pawar, S. M.; Kim, Jin Hyeok

2018-01-01

The development of an inexpensive, stable, and highly active electrocatalyst for oxygen evolution reaction (OER) is essential for the practical application of water splitting. Herein, we have synthesized an electrodeposited cobalt hydroxide on nickel foam and subsequently annealed in an air atmosphere at 400 °C for 2 h. In-depth characterization of all the films using X-ray diffraction (XRD), X-ray photoelectron emission spectroscopy (XPS), field emission scanning electron microscopy (FE-SEM), electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry (LSV) techniques, which reveals major changes for their structural, morphological, compositional and electrochemical properties, respectively. The cobalt hydroxide nanosheet film shows high catalytic activity with 290 mV overpotential at 10 mA cm-2 and 91 mV dec-1 Tafel slope and robust stability (24 h) for OER in 1 M KOH electrolyte compared to cobalt oxide (340 mV). The better OER activity of cobalt hydroxide in comparison to cobalt oxide originated from high active sites, enhanced surface, and charge transport capability.

In vitro digestible energy of some agricultural residues, as influenced by gamma irradiation and sodium hydroxide

International Nuclear Information System (INIS)

Al-Masri, M.R.

1999-01-01

Experiments have been carried out to study the changes in the values of in vitro apparent organic matter digestibility (IVOMD) and in vitro digestible energy (IVDE) of wheat straw (WS), cotton seed shell (CSS), peanut shell (PS), soybean shell (SS), extracted olive cake (EOC) and extracted unpeeled sunflower seeds (ESS) after irradiation by various doses of gamma radiation (0, 100, 150, 200 kGy) or after spraying with different amounts of sodium hydroxide (NaOH): 0, 2, 4, and 6 g NaOH/25 ml water/100 g DM. The results indicate that there were significant increases in IVOMD and IVDE values for all irradiated samples and for sodium hydroxide treatments except for SS and ESS. Combined treatment of irradiation and sodium hydroxide resulted in a larger increase in the digestible energy than the individual treatments

Study for the determination of samarium, europium,terbium, dysprosium and yttrium in gadolinium oxide matrix by means of atomic absorption spectrophotometry using a graphite furnace

International Nuclear Information System (INIS)

Caires, A.C.F.

1985-01-01

A study for determination of samarium, europium, terbium, dysprosium and yttrium in a gadolinium oxide matrix by atomic absorption spectrophotometry using a graphite furnace is presented. The best charrring and atomization conditions were estabilished for each element, the most convenient ressonance lines being selected as well. The study was carried out for the mentioned lanthanides both when pure and when in binary mixtures with gadolinium, besides those where all for them were together with gadolinium. The determination limits for pure lanthanides were found to be between 1.3 and 9.6 ng assuming a 20% relative standard deviation as acceptable. The detection limits were in the range 0.51 and 7.5 ng, assuming as positive any answer higher than twofold the standard deviation. (author) [pt

Iron oxide hydroxide nanoflower assisted removal of arsenic from water

Energy Technology Data Exchange (ETDEWEB)

Raul, Prasanta Kumar, E-mail: prasanta.drdo@gmail.com [Defence Research Laboratory, Post Bag No. 2, Tezpur 784001, Assam (India); Devi, Rashmi Rekha; Umlong, Iohborlang M. [Defence Research Laboratory, Post Bag No. 2, Tezpur 784001, Assam (India); Thakur, Ashim Jyoti [Department of Chemical Sciences, Tezpur University, Napaam, Tezpur 784028, Assam (India); Banerjee, Saumen; Veer, Vijay [Defence Research Laboratory, Post Bag No. 2, Tezpur 784001, Assam (India)

2014-01-01

Graphical abstract: Non-magnetic polycrystalline iron oxide hydroxide nanoparticle with flower like morphology is found to play as an effective adsorbent media to remove As(III) from 300 μg L{sup −1} to less than 10 μg L{sup −1} from drinking water over wide range of pH. TEM image clearly reveals that the nanoparticle looks flower like morphology with average particle size less than 20 nm. The maximum sorption capacity of the sorbent is found to be 475 μg g{sup −1} for arsenic at room temperature and the data fitted to different isotherm models indicate the heterogeneity of the adsorbent surface. The material can be regenerated up to 70% using dilute hydrochloric acid and it would be utilized for de-arsenification purposes. - Highlights: • The work includes synthesis of iron oxide hydroxide nanoflower and its applicability for the removal of arsenic from water. • The nanoparticle was characterized using modern instrumental methods like FESEM, TEM, BET, XRD, etc. • The maximum sorption capacity of the sorbent is found to be 475 μg g{sup −1} for arsenic at room temperature. • The sorption is multilayered on the heterogeneous surface of the nano adsorbent. • The mechanism of arsenic removal of IOH nanoflower follows both adsorption and ion-exchange. - Abstract: Non-magnetic polycrystalline iron oxide hydroxide nanoparticle with flower like morphology is found to play as an effective adsorbent media to remove As(III) from 300 μg L{sup −1} to less than 10 μg L{sup −1} from drinking water over wide range of pH. The nanoparticle was characterized by X-ray powder diffraction analysis (XRD), BET surface area, FTIR, FESEM and TEM images. TEM image clearly reveals flower like morphology with average particle size less than 20 nm. The nanoflower morphology is also supported by FESEM images. The maximum sorption capacity of the sorbent is found to be 475 μg g{sup −1} for arsenic and the data fitted to different isotherm models indicate the

Sound velocity in potassium hydroxide aqueous solution

International Nuclear Information System (INIS)

Tsapuryan, Kh.D.; Aleksandrov, A.A.; Kochetkov, A.I.

1992-01-01

Measurements of ultrasonic velocities in potassium hydroxide aqueous solutions are carried out within the frames of studies on improvement of water chemistry in NPP cooling systems. Method of echo pulses superposition with acoustic path length of 41.447 mm is used for measurements. The measurements are performed at 2.6 MHz frequency. Complex temperature dependence of ultrasonic velocity is determined. Ultrasonic velocity dependence on pressure is close to linear one. The formula for calculation of thermodynamic properties of the studied solutions on the basis of experimental data obtained is proposed

Synthesis of Zn/Co/Fe-layered double hydroxide nanowires with controllable morphology in a water-in-oil microemulsion

Energy Technology Data Exchange (ETDEWEB)

Wu Hongyu; Jiao Qingze [School of Chemical Engineering and Environment, Beijing Institute of Technology, Beijing, 100081 (China); Zhao Yun, E-mail: zhaoyun@bit.edu.cn [School of Chemical Engineering and Environment, Beijing Institute of Technology, Beijing, 100081 (China); Huang Silu; Li Xuefei; Liu Hongbo; Zhou Mingji [School of Chemical Engineering and Environment, Beijing Institute of Technology, Beijing, 100081 (China)

2010-02-15

The Zn/Co/Fe-layered double hydroxide nanowires were synthesized via a reverse microemulsion method by using cetyltrimethyl ammonium bromide (CTAB) /n-hexane/n-hexanol/water as Soft-Template. ZnSO{sub 4}, CoSO{sub 4}, Fe{sub 2}(SO{sub 4}){sub 3} and urea were used as raw materials. The influence of reaction temperature, time, urea concentration and Cn (molar ratio of cetyltrimethyl ammonium bromide to water) on the structure and morphology of Zn/Co/Fe-layered double hydroxides was investigated. The samples were characterized using Transmission Electron Microscopy (TEM), Inductively Coupled Plasma (ICP), X-ray Diffraction (XRD) and Infrared Absorption Spectrum (IR). The results indicate that higher temperature is beneficial to the formation of layered double hydroxides, but particles apart from nanowires could be produced if temperature is up to 120 deg. C. By varying the temperature, reaction time, urea concentration and Cn, we got the optimum conditions of synthesizing uniform Zn/Co/Fe-layered double hydroxide nanowires: 100 deg. C, more than 12 h, Cn: 30-33, urea concentration: 0.3 M.

Growth of PbTe nanorods controlled by polymerized tellurium anions and metal(II) amides via composite-hydroxide-mediated approach

International Nuclear Information System (INIS)

Wan Buyong; Hu Chenguo; Liu Hong; Xiong Yufeng; Li Feiyun; Xi Yi; He Xiaoshan

2009-01-01

The pure face-centered-cubic PbTe nanorods have been synthesized by the composite-hydroxide-mediated approach using hydrazine as a reducing agent. The method is based on reaction among reactants in the melts of potassium hydroxide and sodium hydroxide eutectic at 170-220 deg. C and normal atmosphere without using any organic dispersant or surface-capping agent. Scanning electron microscopy, X-ray diffraction, transmission electron microscopy, and energy dispersive X-ray spectroscopy were used to characterize the structure, morphology and composition of the samples. The diameters of nanorods are almost fixed, while the lengths can be tunable under different growth time and temperatures. The growth mechanism of PbTe nanorods is investigated via UV-vis absorption, demonstrating that polymerized tellurium anions and metal(II) amides in the hydrazine hydroxide melts could control the crystallization and growth process of PbTe nanostructures. The band gap of as-synthesized PbTe nanorods has been calculated based on UV-vis-NIR optical diffuse reflectance spectra data.

Growth of PbTe nanorods controlled by polymerized tellurium anions and metal(II) amides via composite-hydroxide-mediated approach

Energy Technology Data Exchange (ETDEWEB)

Wan Buyong [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China); College of Physics and Information Technology, Chongqing Normal University, Chongqing 400047 (China); Hu Chenguo, E-mail: hucg@cqu.edu.cn [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China); Liu Hong [State Key Laboratory of Crystal Materials, Shandong University, Jinan 250100 (China); Xiong Yufeng [National Center for Nanoscience and Technology, Beijing 100080 (China); Li Feiyun; Xi Yi; He Xiaoshan [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China)

2009-09-15

The pure face-centered-cubic PbTe nanorods have been synthesized by the composite-hydroxide-mediated approach using hydrazine as a reducing agent. The method is based on reaction among reactants in the melts of potassium hydroxide and sodium hydroxide eutectic at 170-220 deg. C and normal atmosphere without using any organic dispersant or surface-capping agent. Scanning electron microscopy, X-ray diffraction, transmission electron microscopy, and energy dispersive X-ray spectroscopy were used to characterize the structure, morphology and composition of the samples. The diameters of nanorods are almost fixed, while the lengths can be tunable under different growth time and temperatures. The growth mechanism of PbTe nanorods is investigated via UV-vis absorption, demonstrating that polymerized tellurium anions and metal(II) amides in the hydrazine hydroxide melts could control the crystallization and growth process of PbTe nanostructures. The band gap of as-synthesized PbTe nanorods has been calculated based on UV-vis-NIR optical diffuse reflectance spectra data.

Anchoring samarium oxide nanoparticles on reduced graphene oxide for high-performance supercapacitor

Energy Technology Data Exchange (ETDEWEB)

Dezfuli, Amin Shiralizadeh [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Ganjali, Mohammad Reza, E-mail: ganjali@khayam.ut.ac.ir [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Biosensor Research Center, Endocrinology & Metabolism Molecular-Cellular Sciences Institute, Tehran University of Medical Sciences, Tehran (Iran, Islamic Republic of); Naderi, Hamid Reza [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of)

2017-04-30

Highlights: • Samarium oxide nanoparticles have been anchored on the surface of reduced graphene oxide for the first time. • Sm{sub 2}O{sub 3}/RGO nanocomposite show high capacitance, good rate and cycling performance. • Sm{sub 2}O{sub 3}/RGO nanocomposite can serve as efficient electrode material for energy storage. • The best composite electrode exhibits specific capacitance of 321 F g{sup −1} in 2 mV s{sup −1}. - Abstract: We have synthesized Sm{sub 2}O{sub 3} nanoparticles (SmNs) and anchored them onto the surface of reduced graphene oxide (RGO) through a self-assembly thereof by utilizing a facile sonochemical procedure. The nanomaterials were characterized by means of powder X-ray diffraction (XRD), Field-emission scanning electron microscopy (FE-SEM), fourier transform infrared spectroscopy (FT-IR) spectra, and X-ray photoelectron spectroscopy (XPS). As the next step, the supercapacitive behavior of the resulting nanocomposites were investigated when used as electrode material, through with cyclic voltammetric (CV), galvanostatic charge-discharge and electrochemical impedance spectroscopy (EIS) techniques. The SmNs decorated RGO (SmN-RGO) nanocomposites were found to possess a specific capacitance (SC) of 321 F g{sup −1} when used in a 0.5 M Na{sub 2}SO{sub 4} solution as an electrolyte, in a scan rate of 2 mV s{sup −1}. The SC of the SmN-RGO based electrodes were also found to be 268 F g{sup −1} at a current density of 2 A g{sup −1} through galvanostatic charge-discharge tests. The outstanding properties of the SmN-RGOs were attributed to synergy of the high charge mobility of SmNs and the flexibility of the sheets of RGOs. Additionally, the nano-composite revealed a unique cycling durability (maintaining 99% of its SC even after 4000 cycles).

Titration of Monoprotic Acids with Sodium Hydroxide Contaminated by Sodium Carbonate.

Science.gov (United States)

Michalowski, Tadeusz

1988-01-01

Discusses the effects of using carbon dioxide contaminated sodium hydroxide solution as a titrant for a solution of a weak monoprotic acid and the resulting distortion of the titration curve in comparison to one obtained when an uncontaminated titrant is used. (CW)

A NEW PROCESS DEVELOPED FOR SEPARATION OF LIGNIN FROM AMMONIUM HYDROXIDE PRETREATMENT SOLUTIONS

Energy Technology Data Exchange (ETDEWEB)

Sherman, S.; Gorensek, M.; Milliken, C.

2010-12-14

A method is described for separating lignin from liquid solutions resulting from the pretreatment of lignocellulosic materials such as switchgrass with ammonium hydroxide. The method involves a sequence of steps including acidification, evaporation, and precipitation or centrifugation that are performed under defined conditions, and results in a relatively pure, solid lignin product. The method is tested on ammonium hydroxide solutions containing lignin extracted from switchgrass. Experimental results show that the method is capable of recovering between 66-95% of dissolved lignin as a precipitated solid. Cost estimates of pilot-scale and industrial-scale expressions of the process indicate that breakeven lignin prices of $2.36/kg and $0.78/kg, respectively, may be obtainable with this recovery method.

Electroosmotic dewatering of chalk sludge, iron hydroxide sludge, wet fly ash and biomass

Energy Technology Data Exchange (ETDEWEB)

Hansen, H.K.; Kristensen, I.V.; Ottosen, L.M.; Villumsen, A. [Dept. of Geology and Geotechnical Engineering, The Technical Univ. of Denmark, Lyngby (Denmark)

2001-07-01

Electroosmotic dewatering has been tested in laboratory cells for 4 different porous materials: chalk sludge, iron hydroxide sludge, wet fly ash and biomass sludge from enzyme production. In all cases it was possible to remove water when passing electric DC current through the material. Casagrande's coefficients for the three materials where determined at different water contents. In the electroosmotic experiments shown in this work chalk can be dewatered from 40% to 79% DM (dry matter), fly ash from 75 to 82% DM, iron hydroxide sludge from 2.7 to 19% DM and biomass from 3 to 33% DM. The process was not optimised indicating that higher dry matter contents could be achieved. (orig.)

Synthesis, spectroscopic analysis and electrochemical performance of modified β-nickel hydroxide electrode with CuO

Directory of Open Access Journals (Sweden)

B. Shruthi

2017-03-01

Full Text Available In the present work, a modified β-nickel hydroxide (β-Ni(OH2 electrode material with CuO has been prepared using a co-precipitation method. The structure and property of the modified β-Ni(OH2 with CuO were characterized by X-ray diffraction (XRD, Fourier Transform infra-red (FT-IR, Raman and thermal gravimetric-differential thermal analysis (TG-DTA techniques. The results of the FT-IR spectroscopy and TG-DTA indicate that the modified β-Ni(OH2 electrode materials contain intercalated water molecules and anions. A pasted–type electrode was prepared using nickel hydroxide powder as the main active material on a nickel sheet as a current collector. Cyclic voltammetry (CV and Electrochemical impedance spectroscopy (EIS studies were undertaken to assess the electrochemical behavior of pure β-Ni(OH2 and modified β-Ni(OH2 electrode with CuO in a 6 M KOH electrolyte. The addition of CuO into β-nickel hydroxide was found to enhance the reversibility of the electrode reaction and also increase the separation of the oxidation current peak of the active material from the oxygen evolution current. The modified nickel hydroxide with CuO was also found to exhibit a higher proton diffusion coefficient and a lower charge transfer resistance. These findings suggest that the modified β-Ni(OH2 with CuO possesses an enhanced electrochemical response and thus can be recognized as a promising candidate for battery electrode applications.

Degradation of l-polylactide during melt processing with layered double hydroxides

DEFF Research Database (Denmark)

Gerds, Nathalie; Katiyar, Vimal; Koch, Christian Bender

2012-01-01

PLA was melt compounded in small-scale batches with two forms of laurate-modified magnesium–aluminum layered double hydroxide (Mg-Al-LDH-C12), the corresponding carbonate form (Mg-Al-LDH-CO3) and a series of other additives. Various methods were then adopted to characterize the resulting compounds...... in an effort to gain greater insights into PLA degradation during melt processing. PLA molecular weight reduction was found to vary according to the type of LDH additive. It is considered that the degree of particle dispersion and LDH exfoliation, and hence the accessibility of the hydroxide layer surfaces...... and catalytically active Mg site centers are causative factors for PLA degradation. Interestingly, the release of water under the processing conditions was found to have a rather small effect on the PLA degradation. Low loadings of sodium laurate also caused PLA degradation indicating that carboxylate chain ends...

Polymethyl methacrylate and polystyrene with layered double hydroxide nano composites: In situ synthesis, morphology and thermal properties

International Nuclear Information System (INIS)

Botan, Rodrigo; Nogueira, Telma R.; Lona, Liliane M.F.; Wypych, Fernando

2011-01-01

Over the past decade, polymer nanocomposites have attracted interest, both in industry and in academia, because they often exhibit remarkable improvement in their properties when compared with pure polymer or conventional micro and macro-composites using low levels of reinforcements. In this work polymethyl methacrylate and polystyrene reinforced with layered double hydroxide, which was intercalated with sodium dodecyl sulfate were synthesized by in situ bulk polymerization. The nanocomposites were characterized and compared by X-ray diffraction, thermogravimetric analysis and flammability test. The X-ray diffraction demonstrated that synthesized nanocomposites showed a high global dispersion of layered double hydroxide, suggesting exfoliated morphology. The result of thermogravimetric analysis and flammability test for synthesized polystyrene/ layered double hydroxide nanocomposite presented a significant improvement in thermal stability and flammability property when compared with pure polymer. (author)

Novel synthesis of magnesium hydroxide nanoparticles modified with organic phosphate and their effect on the flammability of acrylonitrile-butadiene styrene nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Attia, Nour F., E-mail: drnour2005@yahoo.com [Fire Protection Laboratory, Chemistry Division, National Institute of Standards, 136, Giza 12211 (Egypt); Goda, Emad S.; Nour, M.A. [Fire Protection Laboratory, Chemistry Division, National Institute of Standards, 136, Giza 12211 (Egypt); Sabaa, M.W. [Chemistry Department, Faculty of Science, Cairo University, NahdetMisr Street, Giza 12613 (Egypt); Hassan, M.A., E-mail: Mohamed_a_hassan@hotmail.com [Fire Protection Laboratory, Chemistry Division, National Institute of Standards, 136, Giza 12211 (Egypt)

2015-11-15

New and facile method for the synthesis and modification of magnesium hydroxide nanoparticles has been developed. The organic phosphate was used to facilitate the synthesis and wrapping of magnesium hydroxide nanoparticles with organic phosphate shell. The size of the nanoparticles wrapped with phosphate has an average diameter range from 46 to 125 nm. The preparation method has governed the nanoparticles diameter based on reaction time. Thermal stability and morphological properties of the new nanoparticles coated phosphates were investigated. The developed magnesium hydroxide nanoparticles-organic phosphate achieved a very good compatibility when dispersed in acrylonitrile-butadiene styrene polymer (ABS) produced dispersed nanocomposites. The flammability and thermal properties of the new polymer nanocomposites were studied. The rate of burning of the nanocomposites was reduced to 9.8 mm/min compared to 15, 21.9 and 42.5 mm/min for polymer-conventional magnesium hydroxide composite, polymer-conventional magnesium hydroxide-organic phosphate composite and virgin polymer, respectively. The peak heat release rate (PHRR) and total heat release (THR) of the new nanocomposites were recorded as 243.4 kW/m{sup 2} and 19.2 MJ/m{sup 2}, respectively, achieved 71% reduction for PHRR and 55% for THR. The synergism between magnesium hydroxide nanoparticles and organic phosphates shell was also studied. The developed nanoparticles suppressed the emission of toxic gases. The different materials were characterized using thermal gravimetric analysis, fourier transform infrared spectroscopy, transmission electron microscopy. The flammability properties were evaluated using UL94 horizontal method and cone calorimeter. The dispersion of magnesium hydroxide nanoparticles-organic phosphate in ABS was studied using scanning electron microscope. - Highlights: • Novel and facile nanoparticles synthesis and modification have developed. • Magnesium hydroxide nanoparticles size has

One-Pot Microwave-Assisted Synthesis of Graphene/Layered Double Hydroxide (LDH) Nanohybrids

Institute of Scientific and Technical Information of China (English)

Sunil P Lonkar; Jean-Marie Raquez; Philippe Dubois

2015-01-01

A facile and rapid method to synthesize graphene/layered double hydroxide (LDH) nanohybrids by a micro-wave technique is demonstrated. The synthesis procedure involves hydrothermal crystallization of Zn–Al LDH at the same time in situ reduction of graphene oxide (GO) to graphene. The microstructure, composition, and morphology of the resulting graphene/LDH nanohybrids were characterized. The results confirmed the formation of nanohybrids and the reduction of graphene oxide. The growth mechanism of LDH and in situ reduction of GO were discussed. The LDH sheet growth was found to prevent the scrolling of graphene layers in resulting hybrids. The electrochemical properties exhibit superior performance for graphene/Zn–Al LDH hybrids over pristine graphene. The present approach may open a strategy in hybridizing graphene with multimetallic nano-oxides and hydroxides using microwave method.

One-Pot Microwave-Assisted Synthesis of Graphene/Layered Double Hydroxide(LDH) Nanohybrids

Institute of Scientific and Technical Information of China (English)

Sunil P.Lonkar; Jean-Marie Raquez; Philippe Dubois

2015-01-01

A facile and rapid method to synthesize graphene/layered double hydroxide(LDH)nanohybrids by a microwave technique is demonstrated.The synthesis procedure involves hydrothermal crystallization of Zn–Al LDH at the same time in situ reduction of graphene oxide(GO)to graphene.The microstructure,composition,and morphology of the resulting graphene/LDH nanohybrids were characterized.The results confirmed the formation of nanohybrids and the reduction of graphene oxide.The growth mechanism of LDH and in situ reduction of GO were discussed.The LDH sheet growth was found to prevent the scrolling of graphene layers in resulting hybrids.The electrochemical properties exhibit superior performance for graphene/Zn–Al LDH hybrids over pristine graphene.The present approach may open a strategy in hybridizing graphene with multimetallic nano-oxides and hydroxides using microwave method.

Structural characterization of nickel oxide/hydroxide nanosheets produced by CBD technique

Energy Technology Data Exchange (ETDEWEB)

Taşköprü, T., E-mail: ttaskopru@anadolu.edu.tr [Department of Physics, Anadolu University, Eskişehir 26470 (Turkey); Department of Physics, Çankırı Karatekin University, Çankırı 18100 (Turkey); Zor, M.; Turan, E. [Department of Physics, Anadolu University, Eskişehir 26470 (Turkey)

2015-10-15

Graphical abstract: SEM images of (a) as deposited β-Ni(OH)2 and (b) NiO samples deposited with pH 10 solution. The inset figures shows the absorbance spectra of (a) β-Ni(OH)2 and (b) NiO samples. - Highlights: • The formation of β-Ni(OH){sub 2} and NiO were confirmed with XRD, SEM, FT-IR and Raman. • Porous nickel oxide was synthesized after heat treatment of nickel hydroxide. • The increase in pH value changes the nanoflake structure to hexagonal nanosheet. • On increasing the pH from 8 to 11, the band gap decreases from 3.52 to 3.37 eV. - Abstract: Nickel hydroxide samples were deposited onto glass substrates using Ni(NO{sub 3}){sub 2}·6H{sub 2}O and aqueous ammonia by chemical bath deposition technique. The influence of pH of solution was investigated by means of X-ray diffraction, field emission scanning electron microscopy, Fourier transform infrared, Raman spectroscopy, optical absorption and BET analysis. The as-deposited samples were identified as β-Ni(OH){sub 2}, were transformed into NiO after heat treatment in air at 500 °C for 2 h. Porous nickel oxide nanosheets are obtained by heating nickel hydroxide nanosheets. The optical transitions observed in the absorbance spectra below optical band gap is due to defects or Ni{sup 2+} vacancies in NiO samples. The band gap energy of NiO samples changes between 3.37 and 3.52 eV depending on the pH values.

New layered double hydroxides by prepared by the intercalation of gibbsite

International Nuclear Information System (INIS)

Rees, Jennifer R.; Burden, Chloe S.; Fogg, Andrew M.

2015-01-01

New layered double hydroxides (LDHs) with the composition [MAl 4 (OH) 12 ]Cl 2 ·1.5H 2 O (M=Co, Ni) have been prepared by reacting gibbsite, γ-Al(OH) 3 , with the appropriate chloride salt in a synthesis in which the water of crystallization is the only solvent present and fully characterized. These LDHs have been shown to undergo facile anion exchange reactions with both organic and inorganic anions at room temperature making them comparable to other LDHs in this respect. Reactions under the same conditions with CuCl 2 ·2H 2 O and ZnCl 2 failed to form the desired LDHs but those with nitrate salts did lead to the formation of the previously reported [MAl 4 (OH) 12 ](NO 3 ) 2 ·1.5H 2 O (M=Co, Ni) compounds. - Graphical abstract: New layered double hydroxides (LDHs) with the composition [MAl 4 (OH) 12 ]Cl 2 ·1.5H 2 O (M=Co, Ni) have been prepared by reacting gibbsite, γ-Al(OH) 3 , with the appropriate chloride salt in a synthesis in which no additional solvent is used and fully characterized. These LDHs have been shown to undergo facile anion exchange reactions with both organic and inorganic anions at room temperature. - Highlights: • Synthesis of new layered double hydroxides, [MAl 4 (OH) 12 ]Cl 2 ·1.5H 2 O (M=Co, Ni). • Demonstration of the anion exchange capacity with both organic and inorganic anions. • Demonstration of the generality of the synthesis for LDHs

Study of unstable valences of cadmium and samarium by pulse radiolysis. Influence of complexation by some synthetical ionophores

International Nuclear Information System (INIS)

Lerat-Parizot, O.

1992-01-01

Instable valences of cations in solution are evidenced by pulse radiolysis, in spite of a lifetime often lower than a milli-second they participate to electron transfer reactions, owing to their redox potential. In this work are studied Cd + and Sm 2+ obtained respectively by reduction of Cd 2+ and Sm 3+ by a solvated electron. The reactivity of Cd + in a cryptand and in a coronand is studied; it is a powerful reducing agent (redox potential -2V) going back to the stable valence by electron transfer to an acceptor. Transfer kinetics is studied by reduction of organic molecules, effect of solvents and ligands is also examined. For samarium the reduction kinetics by hydrated electrons is increased when the ion is in a cryptand in agreement with electrochemical observations, showing that the valence 2+ is stabilized in respect to the valence 3+ for lanthanides. The difference of behaviour between Cd + and Sm 2+ is probably due to the fact that for Cd the transferred electron comes from the external layer and for Sm it is a f electron protected by the 5s and 5p orbitals

Hydrophilic block copolymer-directed growth of lanthanum hydroxide nano-particles

Energy Technology Data Exchange (ETDEWEB)

Bouyer, F.; Sanson, N.; Gerardin, C. [Laboratoire de Materiaux Catalytiques et Catalyse en Chimie Organique, UMR 5618 CNRS-ENSCM-UM1, FR 1878, Institut Gerhardt, 34 - Montpellier (France); Destarac, M. [Centre de Recherches Rhodia Aubervilliers, 93 - Aubervilliers (France)

2006-03-15

Stable hairy lanthanum hydroxide nano-particles were synthesized in water by performing hydrolysis and condensation reactions of lanthanum cations in the presence of double hydrophilic poly-acrylic acid-b-polyacrylamide block copolymers (PAA-b-PAM). In the first step, the addition of asymmetric PAA-b-PAM copolymers (M{sub w,PAA} {<=} M{sub w,PAM}) to lanthanum salt solutions, both at pH = 5.5, induces the formation of monodispersed micellar aggregates, which are predominantly isotropic. The core of the hybrid aggregates is constituted of a lanthanum polyacrylate complex whose formation is due to bidentate coordination bonding between La{sup 3+} and acrylate groups, as shown by ATR-FTIR experiments and pH measurements. The size of the micellar aggregates depends on the molecular weight of the copolymer but is independent of the copolymer to metal ratio in solution. In the second step, the hydrolysis of lanthanum ions is induced by addition of a strong base such as sodium hydroxide. Either flocculated suspensions or stable anisotropic or spherical nano-particles of lanthanum hydrolysis products were obtained depending on the metal complexation ratio [acrylate]/[La]. The variation of that parameter also enables the control of the size of the core-corona nano-particles obtained by lanthanum hydroxylation. The asymmetry degree of the copolymer was shown to influence both the size and the shape of the particles. Elongated particles with a high aspect ratio, up to 10, were obtained with very asymmetric copolymers (M{sub w,PAM}/M{sub w,PAA}{>=}10) while shorter rice grain-like particles were obtained with a less asymmetric copolymer. The asymmetry degree also influences the value of the critical metal complexation degree required to obtain stable colloidal suspensions of polymer-stabilized lanthanum hydroxide. (authors)

A prospective, open, comparative study of 5% potassium hydroxide solution versus cryotherapy in the treatment of genital warts in men.

Science.gov (United States)

Camargo, Caio Lamunier de Abreu; Belda Junior, Walter; Fagundes, Luiz Jorge; Romiti, Ricardo

2014-01-01

Genital warts are caused by human papillomavirus infection and represent one of the most common sexually transmitted diseases. Many infections are transient but the virus may recur, persist, or become latent. To date, there is no effective antiviral treatment to eliminate HPV infection and most therapies are aimed at the destruction of visible lesions. Potassium hydroxide is a strong alkali that has been shown to be safe and effective for the treatment of genital warts and molluscum contagiosum. Cryotherapy is considered one of the most established treatments for genital warts. No comparative trials have been reported to date on the use of potassium hydroxide for genital warts. A prospective, open-label, randomized clinical trial was conducted to compare topical potassium hydroxide versus cryotherapy in the treatment of genital warts affecting immunocompetent, sexually active men. Over a period of 10 months, 48 patients were enrolled. They were randomly divided into two groups and selected on an alternative basis for either potassium hydroxide therapy or cryotherapy. While response to therapy did not differ substantially between both treatment modalities, side effects such as local pain and post-treatment hypopigmentation were considerably more prevalent in the groups treated using cryotherapy. In our study, potassium hydroxide therapy proved to be at least as effective as cryotherapy and offered the benefit of a better safety profile. Topical 5% potassium hydroxide presents an effective, safe, and low-cost treatment modality for genital warts in men and should be included in the spectrum of therapies for genital warts.

A prospective, open, comparative study of 5% potassium hydroxide solution versus cryotherapy in the treatment of genital warts in men*

Science.gov (United States)

Camargo, Caio Lamunier de Abreu; Belda, Walter; Fagundes, Luiz Jorge; Romiti, Ricardo

2014-01-01

BACKGROUND Genital warts are caused by human papillomavirus infection and represent one of the most common sexually transmitted diseases. Many infections are transient but the virus may recur, persist, or become latent. To date, there is no effective antiviral treatment to eliminate HPV infection and most therapies are aimed at the destruction of visible lesions. Potassium hydroxide is a strong alkali that has been shown to be safe and effective for the treatment of genital warts and molluscum contagiosum. Cryotherapy is considered one of the most established treatments for genital warts. No comparative trials have been reported to date on the use of potassium hydroxide for genital warts. OBJECTIVE A prospective, open-label, randomized clinical trial was conducted to compare topical potassium hydroxide versus cryotherapy in the treatment of genital warts affecting immunocompetent, sexually active men. METHODS Over a period of 10 months, 48 patients were enrolled. They were randomly divided into two groups and selected on an alternative basis for either potassium hydroxide therapy or cryotherapy. While response to therapy did not differ substantially between both treatment modalities, side effects such as local pain and post-treatment hypopigmentation were considerably more prevalent in the groups treated using cryotherapy. RESULT In our study, potassium hydroxide therapy proved to be at least as effective as cryotherapy and offered the benefit of a better safety profile. CONCLUSION Topical 5% potassium hydroxide presents an effective, safe, and low-cost treatment modality for genital warts in men and should be included in the spectrum of therapies for genital warts. PMID:24770498

Iron Hydroxide Minerals Drive Organic and Phosphorus Chemistry in Subsurface Redox / pH Gradients

Science.gov (United States)

Flores, E.; Barge, L. M.; VanderVelde, D.; Baum, M.

2017-12-01

Iron minerals, particularly iron oxides and oxyhydroxides, are prevalent on Mars and may exist in mixed valence or even reduced states beneath the oxidized surface. Iron (II,III) hydroxides, including green rust, are reactive and potentially catalytic minerals that can absorb and concentrate charged species, while also driving chemical reactions. These minerals are highly redox-sensitive and the presence of organics and/or phosphorus species could affect their mineralogy and/or stability. Conversely, the minerals might be able to drive chemical processes such as amino acid formation, phosphorus oxyanion reactions, or could simply selectively preserve organic species via surface adsorption. In an open aqueous sediment column, soluble products of mineral-driven reactions could also diffuse to sites of different chemical conditions to react even further. We synthesized Fe-hydroxide minerals under various conditions relevant to early Earth and ancient Mars (>3.0 Gyr), anoxically and in the presence of salts likely to have been present in surface or ground waters. Using these minerals we conducted experiments to test whether iron hydroxides could promote amino acid formation, and how the reaction is affected by subsurface gradients of redox, pH, and temperature. We also tested the adsorption of organic and phosphorus species onto Fe-hydroxide minerals at different conditions within the gradients. The suite of organic or phosphorus signatures that may be found in a particular mineral system is a combination of what is synthesized there, what is preferentially concentrated / retained there, and what is preserved against degradation. Further work is needed to determine how these processes could have proceeded on Mars and what mineral-organic signatures, abiotic or otherwise, would be produced from such processes.

Microwave-assisted hydrothermal synthesis of coralloid nanostructured nickel hydroxide hydrate and thermal conversion to nickel oxide

International Nuclear Information System (INIS)

Lai, Teh-Long; Lai, Yuan-Lung; Yu, Jen-Wei; Shu, Youn-Yuen; Wang, Chen-Bin

2009-01-01

Coralloid nanostructured nickel hydroxide hydrate has been successfully synthesized by a simple microwave-assisted hydrothermal process using nickel sulfate hexahydrate as precursor and urea as hydrolysis-controlling agent. A pure coralloid nanostructured nickel oxide can be obtained from the nickel hydroxide hydrate after calcination at 400 deg. C. The thermal property, structure and morphology of samples were characterized by thermogravimetry (TG), temperature-programmed reduction (TPR), X-ray (XRD), infrared spectroscopy (IR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM).

Microwave-assisted hydrothermal synthesis of coralloid nanostructured nickel hydroxide hydrate and thermal conversion to nickel oxide

Energy Technology Data Exchange (ETDEWEB)

Lai, Teh-Long [Environmental Analysis Laboratory, Department of Chemistry, National Kaohsiung Normal University, Kaohsiung 802, Taiwan (China); Lai, Yuan-Lung [Department of Mechanical and Automation Engineering, Da-Yeh University, Changhua 515, Taiwan (China); Yu, Jen-Wei [Environmental Analysis Laboratory, Department of Chemistry, National Kaohsiung Normal University, Kaohsiung 802, Taiwan (China); Shu, Youn-Yuen, E-mail: shuyy@nknucc.nknu.edu.tw [Environmental Analysis Laboratory, Department of Chemistry, National Kaohsiung Normal University, Kaohsiung 802, Taiwan (China); Wang, Chen-Bin, E-mail: chenbin@ccit.edu.tw [Department of Applied Chemistry and Materials Science, Chung Cheng Institute of Technology, National Defense University, Tahsi, Taoyuan 335, Taiwan (China)

2009-10-15

Coralloid nanostructured nickel hydroxide hydrate has been successfully synthesized by a simple microwave-assisted hydrothermal process using nickel sulfate hexahydrate as precursor and urea as hydrolysis-controlling agent. A pure coralloid nanostructured nickel oxide can be obtained from the nickel hydroxide hydrate after calcination at 400 deg. C. The thermal property, structure and morphology of samples were characterized by thermogravimetry (TG), temperature-programmed reduction (TPR), X-ray (XRD), infrared spectroscopy (IR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM).

Optical properties of cerium oxide (CeO2) nanoparticles synthesized by hydroxide mediated method

Science.gov (United States)

Ali, Mawlood Maajal; Mahdi, Hadeel Salih; Parveen, Azra; Azam, Ameer

2018-05-01

The nanoparticles of cerium oxide have been successfully synthesized by hydroxide mediated method, using cerium nitrate and sodium hydroxide as precursors. The microstructural properties were analyzed by X-ray diffraction technique (XRD). The X-ray diffraction results show that the cerium oxide nanoparticles were in cubic structure. The optical absorption spectra of cerium oxide were recorded by UV-VIS spectrophotometer in the range of 320 to 600 nm and photoluminescence spectra in the range of 400-540 nm and have been presented. The energy band gap was determined by Tauc relationship. The crystallite size was determined from Debye-Scherer equation and came out to be 6.4 nm.

The determination of hydroxide and carbonate in concentrated sodium chloride solutions

NARCIS (Netherlands)

Roolvink, W.B.; Bos, M.

1980-01-01

A computer method for the determination of carbonate and hydroxide in concentrated (2.89 M) sodium chloride solutions is described. The method is based on multiparametric curve-fitting and can also be applied to salts of dibasic acids with unknown equilibrium constants. The systematic error is not

The photoluminescence of Co-Al-layered double hydroxide

Institute of Scientific and Technical Information of China (English)

无

2007-01-01

We report a new optical behaviour of pure Co-Al-layered double hydroxide (LDH). It was found that the Co-Al-LDH sample could emit fluorescence without any fluorescent substances intercalated. Its excitation spectrum shows a maximum peak near the wavelength 370 nm, the maximum emission peak appears at 430 nm and the photoluminescence colour of the Co-Al-LDH sample is blue. This new optical property will be expected to extend the potential applications of LDHs in optical materials field.

Nanostructures based on alumina hydroxides inhibit tumor growth

Science.gov (United States)

Fomenko, A. N.; Korovin, M. S.

2017-09-01

Nanoparticles and nanostructured materials are one of the most promising developments for cancer therapy. Gold nanoparticles, magnetic nanoparticles based on iron and its oxides and other metal oxides have been widely used in diagnosis and treatment of cancer. Much less research attention has been payed to nanoparticles and nanostructures based on aluminum oxides and hydroxides as materials for cancer diagnosis and treatment. However recent investigations have shown promising results regarding these objects. Here, we review the antitumor results obtained with AlOOH nanoparticles.

A new route to copper nitrate hydroxide microcrystals

International Nuclear Information System (INIS)

Niu Haixia; Yang Qing; Tang Kaibin

2006-01-01

A solution evaporation route has been successfully developed for the growth of copper nitrate hydroxide microcrystals using copper nitrate solution as the starting material in the absence of any surfactants or templates. The products were characterized by X-ray diffraction (XRD), infrared (IR) spectrum, scanning electron microscopy (SEM) and thermogravimetric (TG) analysis measurements. Controlled experiments suggested that the reaction temperature and solution concentration played an important role on the formation of the products. A possible formation mechanism of the products was also proposed

Synthesis of Platinum-Nickel Hydroxide Nanocomposites for Electrocatalytic Reduction of Water

KAUST Repository

Wang, Lei

2016-11-25

Water electrolysis represents a promising solution for storage of renewable but intermittent electrical energy in hydrogen molecules. This technology is however challenged by the lack of efficient electrocatalysts for the hydrogen and oxygen evolution reactions. Here we report on the synthesis of platinum-nickel hydroxide nanocomposites and their electrocatalytic applications for water reduction. An in situ reduction strategy taking advantage of the Ni(II)/Ni(III) redox has been developed to enable and regulate the epitaxial growth of Pt nanocrystals on single-layer Ni(OH)2 nanosheets. The obtained nanocomposites (denoted as Pt@2D-Ni(OH)2) exhibit an improvement factor of 5 in catalytic activity and a reduction of up to 130 mV in overpotential compared to Pt for the hydrogen evolution reaction (HER). A combination of electron microscopy/spectroscopy characterization, electrochemical studies and density functional calculations was employed to uncover the structures of the metal-hydroxide interface and understand the mechanisms of catalytic enhancement.

Synthesis of Platinum-Nickel Hydroxide Nanocomposites for Electrocatalytic Reduction of Water

KAUST Repository

Wang, Lei; Zhu, Yihan; Zeng, Zhenhua; Lin, Chong; Giroux, Michael; Jiang, Lin; Han, Yu; Greeley, Jeffrey; Wang, Chao; Jin, Jian

2016-01-01

Water electrolysis represents a promising solution for storage of renewable but intermittent electrical energy in hydrogen molecules. This technology is however challenged by the lack of efficient electrocatalysts for the hydrogen and oxygen evolution reactions. Here we report on the synthesis of platinum-nickel hydroxide nanocomposites and their electrocatalytic applications for water reduction. An in situ reduction strategy taking advantage of the Ni(II)/Ni(III) redox has been developed to enable and regulate the epitaxial growth of Pt nanocrystals on single-layer Ni(OH)2 nanosheets. The obtained nanocomposites (denoted as Pt@2D-Ni(OH)2) exhibit an improvement factor of 5 in catalytic activity and a reduction of up to 130 mV in overpotential compared to Pt for the hydrogen evolution reaction (HER). A combination of electron microscopy/spectroscopy characterization, electrochemical studies and density functional calculations was employed to uncover the structures of the metal-hydroxide interface and understand the mechanisms of catalytic enhancement.

Synthesis of Nickel and Nickel Hydroxide Nanopowders by Simplified Chemical Reduction

Directory of Open Access Journals (Sweden)

Jeerapan Tientong

2014-01-01

Full Text Available Nickel nanopowders were synthesized by a chemical reduction of nickel ions with hydrazine hydrate at pH ~12.5. Sonication of the solutions created a temperature of 54–65°C to activate the reduction reaction of nickel nanoparticles. The solution pH affected the composition of the resulting nanoparticles. Nickel hydroxide nanoparticles were formed from an alkaline solution (pH~10 of nickel-hydrazine complexed by dropwise titration. X-ray diffraction of the powder and the analysis of the resulting Williamson-Hall plots revealed that the particle size of the powders ranged from 12 to 14 nm. Addition of polyvinylpyrrolidone into the synthesis decreased the nickel nanoparticle size to approximately 7 nm. Dynamic light scattering and scanning electron microscopy confirmed that the particles were in the nanometer range. The structure of the synthesized nickel and nickel hydroxide nanoparticles was identified by X-ray diffraction and Fourier transform infrared spectroscopy.

Intercalation and controlled release properties of vitamin C intercalated layered double hydroxide

Energy Technology Data Exchange (ETDEWEB)

Gao, Xiaorui, E-mail: gxr_1320@sina.com [College of Science, Hebei University of Engineering, Handan 056038 (China); School of Chemistry and Chemical Engineering, Southeast University, Nanjing 211189 (China); Chemistry Research Laboratory, University of Oxford, Mansfield Road, Oxford OX1 3TA (United Kingdom); Lei, Lixu [School of Chemistry and Chemical Engineering, Southeast University, Nanjing 211189 (China); O' Hare, Dermot [Chemistry Research Laboratory, University of Oxford, Mansfield Road, Oxford OX1 3TA (United Kingdom); Xie, Juan [College of Science, Hebei University of Engineering, Handan 056038 (China); Gao, Pengran [School of Chemistry and Chemical Engineering, Southeast University, Nanjing 211189 (China); Chang, Tao [College of Science, Hebei University of Engineering, Handan 056038 (China)

2013-07-15

Two drug-inorganic composites involving vitamin C (VC) intercalated in Mg–Al and Mg–Fe layered double hydroxides (LDHs) have been synthesized by the calcination–rehydration (reconstruction) method. Powder X-ray diffraction (XRD), Fourier transform infrared (FTIR), and UV–vis absorption spectroscopy indicate a successful intercalation of VC into the interlayer galleries of the LDH host. Studies of VC release from the LDHs in deionised water and in aqueous CO{sub 3}{sup 2−} solutions imply that Mg{sub 3}Al–VC LDH is a better controlled release system than Mg{sub 3}Fe–VC LDH. Analysis of the release profiles using a number of kinetic models suggests a solution-dependent release mechanism, and a diffusion-controlled deintercalation mechanism in deionised water, but an ion exchange process in CO{sub 3}{sup 2−} solution. - Graphical abstract: Vitamin C anions have been intercalated in the interlayer space of layered double hydroxide and released in CO{sub 3}{sup 2−} solution and deionised water. - Highlights: • Vitamin C intercalated Mg–Al and Mg–Fe layered double hydroxides were prepared. • Release property of vitamin C in aqueous CO{sub 3}{sup 2−} solution is better. • Avrami-Erofe’ev and first-order models provide better fit for release results. • Diffusion-controlled and ion exchange processes occur in deionised water. • An ion exchange process occurs in CO{sub 3}{sup 2−} solution.

Hydroxide precursors to produce nanometric YCrO3: Characterization and conductivity analysis

International Nuclear Information System (INIS)

Durán, A.; Meza F, C.; Arizaga, Gregorio Guadalupe Carbajal

2012-01-01

Highlights: ► Y/Cr mixed hydroxide was precipitated with gaseous ammonia. ► The hydroxide treated at 1373 K formed YCrO 3 crystals with 20 nm diameter. ► Electrical properties were different than those found in other methods of synthesis. ► E act suggests small-polarons as conduction mechanisms. -- Abstract: A precursor to produce perovskite-type YCrO 3 was precipitated by bubbling gaseous ammonia into an yttrium/chromium salts solution. X-ray diffraction showed that the as-prepared powders were amorphous. Thermal treatment between 1273 and 1373 K, leads to formation of polycrystalline YCrO 3 with crystal sizes around 20 nm. High resolution X-ray photoelectron spectra showed uniform chemical environment for yttrium and chromium in the amorphous hydroxide and crystalline YCrO 3 . Shifts between Y 3d 5/2 and Cr 2p 3/2 binding energy suggest redistribution or charge transfer between yttrium and chromium ions in the YCrO 3 structure. The electrical properties of YCrO 3 , whose precursors were precipitated with gaseous ammonia are different than those prepared by combustion synthesis. Electrical conductivity presents a sudden increase at ∼473 K, which is associated to the grain size and morphology of the crystallites. The redistribution of charge between Y(III) and Cr(III) is thermally activated by the hopping of small-polarons, which are characterized by the Arrhenius law as the conductive mechanism.

Three-dimensionally networked graphene hydroxide with giant pores and its application in supercapacitors

Science.gov (United States)

Lee, Dongwook; Seo, Jiwon

2014-12-01

The three-dimensionally networked and layered structure of graphene hydroxide (GH) was investigated. After lengthy immersion in a NaOH solution, most of the epoxy groups in the graphene oxide were destroyed, and more hydroxyl groups were generated, transforming the graphene oxide into graphene hydroxide. Additionally, benzoic acid groups were formed, and the ether groups link the neighboring layers, creating a near-3D structure in the GH. To utilize these unique structural features, electrodes with large pores for use in supercapacitors were fabricated using thermal reduction in vacuum. The reduced GH maintained its layered structure and developed a lot of large of pores between/inside the layers. The GH electrodes exhibited high gravimetric as well as high volumetric capacitance.

Effect of ammonium hydroxide on preparation process of YBa2Cu3O7-x superconductor by sol gel method

Directory of Open Access Journals (Sweden)

H Arabi

2006-09-01

Full Text Available  In this paper the effect of ammonium hydroxide addition to the solution of metallic oxide on sol gel preparation process of YBCO is studied with differential thermal analysis, thermal graviometry and X-ray diffraction. Two samples with and without ammonium hydroxide. Ammonium hydroxide prevents both barium nitrate precipitate during the gel preparation and also unwanted reaction as well as increasing homogeneous product. After drying the gel, the samples heated up to 1050°C in DTA apparatus in order to find more accurate the type and the temperature of reaction during the preparation process. After the initial reactions in the samples, Y2Cu2O5 and 123 phases are created in the range of 780-840°C and then the 123 phase is strengthened at 900-950°C. As shown in X-ray data, 123 was the only phase after this range. In addition ammonium hydroxide support and increase the creation of 123 phase at lower temperature.

Intercalation of anionic organic ultraviolet ray absorbers into layered zinc hydroxide nitrate.

Science.gov (United States)

Cursino, Ana Cristina Trindade; Gardolinski, José Eduardo Ferreira da Costa; Wypych, Fernando

2010-07-01

Layered zinc hydroxide nitrate (ZHN) was synthesized and nitrate ions were topotactically exchanged with three different anionic species of commercial organic ultraviolet (UV) ray absorbers: 2-mercaptobenzoic acid, 2-aminobenzoic acid, and 4-aminobenzoic acid. The exchange reactions were confirmed by X-ray powder diffraction (XRPD), Fourier transform infrared spectroscopy (FTIR), ultraviolet visible (UV-Vis) spectroscopy, and thermal analysis (thermogravimetry, TGA, and differential thermal analysis, DTA). In all the anionic exchanged products, evidence of grafting of the organic species onto the inorganic matrix was obtained. In general, after intercalation/grafting, the UV absorption ability was improved in relation to the use of the parent organic material, showing that layered hydroxide salts (LHS) can be good alternative matrixes for the immobilization of organic species with UV-blocking properties in cosmetic products. Copyright 2010 Elsevier Inc. All rights reserved.

Samarium-modified vanadium phosphate catalyst for the selective oxidation of n-butane to maleic anhydride

International Nuclear Information System (INIS)

Wu, Hua-Yi; Wang, Hai-Bo; Liu, Xin-Hua; Li, Jian-Hui; Yang, Mei-Hua; Huang, Chuan-Jing; Weng, Wei-Zheng; Wan, Hui-Lin

2015-01-01

Graphical abstract: The addition of a small amount of Sm into VPO catalyst brought about great changes in its physicochemical properties such as surface area, surface morphology, phase composition and redox property, thus leading to a higher catalytic performance in the selective oxidation of n-butane to maleic anhydride, as compared to the undoped VPO catalyst. - Highlights: • The addition of Sm leads to great changes in the structure of VPO catalyst. • Sm improves performance of VPO for oxidation of n-butane to maleic anhydride. • Catalytic performance is closely related to structure of VPO catalyst. - Abstract: A series of samarium-modified vanadium phosphate catalysts were prepared and studied in selective oxidation of n-butane to maleic anhydride. The catalytic evaluation showed that Sm modification significantly increased the overall n-butane conversion and intrinsic activity. N 2 -adsorption, XRD, SEM, Raman, XPS, EPR and H 2 -TPR techniques were used to investigate the intrinsic difference among these catalysts. The results revealed that the addition of Sm to VPO catalyst can increase the surface area of the catalyst, lead to a significant change in catalyst morphology from plate-like structure into rosette-shape clusters, and largely promote the formation of (VO) 2 P 2 O 7 . All of these were related to the different catalytic performance of Sm-doped and undoped VPO catalysts. The roles of the different VOPO 4 phases and the influence of Sm were also described and discussed

Dynamics of Intercalation/De-Intercalation of Rhodamine B during the Polymorphic Transformation of CdAl Layered Double Hydroxide to the Brucite-Like Cadmium Hydroxide

KAUST Repository

Saliba, Daniel

2016-06-23

Cadmium-Aluminum layered double hydroxide (CdAl LDH) is thermodynamically unstable and transforms to Cd(OH)2 and Al(OH)3 in a short period of time. We present a reaction-diffusion framework that enables us to use in situ steady-state fluorescence spectroscopy to study the kinetics of intercalation of a fluorescent probe (Rhodamine B (RhB)) during the formation of the CdAl LDH and its de-intercalation upon the conversion of the LDH phase to the β phase (Cd(OH)2). The method involves the diffusion of sodium hydroxide into a hydrogel gel matrix containing the aluminum and cadmium ions as well as the species we wish to incorporate in the interlayers of the LDH. The existence of RhB between the LDH layers and its expel during the transition into the β phase are proved via fluorescence microscopy, XRD and ssNMR. The activation energies of intercalation and de-intercalation of RhB are computed and show dependence on the cationic ratio of the corresponding LDH. We find that the energies of de- intercalation are systematically higher than those of intercalation proving that the dyes are stabilized due to the probe-brucite sheets interactions.

Dynamics of Intercalation/De-Intercalation of Rhodamine B during the Polymorphic Transformation of CdAl Layered Double Hydroxide to the Brucite-Like Cadmium Hydroxide

KAUST Repository

Saliba, Daniel; Ezzeddine, Alaa; Emwas, Abdul-Hamid M.; Khashab, Niveen M.; Al-Ghoul, Mazen

2016-01-01

Cadmium-Aluminum layered double hydroxide (CdAl LDH) is thermodynamically unstable and transforms to Cd(OH)2 and Al(OH)3 in a short period of time. We present a reaction-diffusion framework that enables us to use in situ steady-state fluorescence spectroscopy to study the kinetics of intercalation of a fluorescent probe (Rhodamine B (RhB)) during the formation of the CdAl LDH and its de-intercalation upon the conversion of the LDH phase to the β phase (Cd(OH)2). The method involves the diffusion of sodium hydroxide into a hydrogel gel matrix containing the aluminum and cadmium ions as well as the species we wish to incorporate in the interlayers of the LDH. The existence of RhB between the LDH layers and its expel during the transition into the β phase are proved via fluorescence microscopy, XRD and ssNMR. The activation energies of intercalation and de-intercalation of RhB are computed and show dependence on the cationic ratio of the corresponding LDH. We find that the energies of de- intercalation are systematically higher than those of intercalation proving that the dyes are stabilized due to the probe-brucite sheets interactions.

Glycine buffered synthesis of layered iron(II)-iron(III) hydroxides (green rusts)

DEFF Research Database (Denmark)

Yin, Weizhao; Huang, Lizhi; Pedersen, Emil Bjerglund

2017-01-01

Layered Fe(II)-Fe(III) hydroxides (green rusts, GRs) are efficient reducing agents against oxidizing contaminants such as chromate, nitrate, selenite, and nitroaromatic compounds and chlorinated solvents. In this study, we adopted a buffered precipitation approach where glycine (GLY) was used...

Layered Metal Hydroxides Containing Calcium and Their Structural Analysis

Energy Technology Data Exchange (ETDEWEB)

Kim, Tae Hyun; Heo, Il; Lee, Sung Han; Oh, Jae Min [College of Science and Technology, Yonsei University, Wonju (Korea, Republic of); Paek, Seung Min [Kyungpook National University, Daegu (Korea, Republic of); Park, Chung Berm; Choi, Ae Jin [National Institute of Horticultural and Herbal Science of R and D Eumseong (Korea, Republic of); Choy, Jin Ho [Ewha Womans University, Seoul (Korea, Republic of)

2012-06-15

Layered metal hydroxides (LMHs) containing calcium were synthesized by coprecipitation in solution having two different trivalent metal ions, iron and aluminum. Two mixed metal solutions (Ca{sup 2+}/Al{sup 3+} and Ca{sup 2+}/Fe{sup 3+} = 2/1) were added to sodium hydroxide solution and the final pH was adjusted to {approx}11.5 and {approx}13 for CaAl-and CaFe-LMHs. Powder X-ray diffraction (XRD) for the two LMH samples showed well developed (00l) diffractions indicating 2-dimensional crystal structure of the synthesized LMHs. Rietveld refinement of the X-ray diffraction pattern, the local structure analysis through X-ray absorption spectroscopy, and thermal analysis also confirmed that the synthesized precipitates show typical structure of LMHs. The chemical formulae, Ca{sub 2.04}Al{sub 1}(OH){sub 6}(NO{sub 3}){center_dot}5.25H{sub 2}O and Ca{sub 2.01}Fe{sub 1}(OH){sub 6}(NO{sub 3}){center_dot}4.75H{sub 2}O were determined by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Particle morphology and thermal behavior for the synthesized LMHs were examined by field emission scanning electron microscopy and thermogravimetric differential scanning calorimetry

Dgroup: DG01196 [KEGG MEDICUS

Lifescience Database Archive (English)

Full Text Available DG01196 Chemical ... DGroup Samarium (153Sm) lexidronam ... D08504 ... Samarium (153Sm) lexidron...am (INN) D05795 ... Samarium Sm 153 lexidronam pentasodium (USAN); Samarium (153Sm) lexidronam sodium (JA

Facile synthesis of deoxycholate intercalated layered double hydroxide nanohybrids via a coassembly process

International Nuclear Information System (INIS)

Wu, Xiaowen; Wang, Shuang; Du, Na; Zhang, Renjie; Hou, Wanguo

2013-01-01

In this paper, we describe a synthesis strategy of deoxycholate (DC) intercalated layered double hydroxide (LDH) nanohybrids via a coassembly method at room temperature. For this strategy, LDH particles were delaminated to well-dispersed 2D nanosheets in formamide, and the resulting LDH nanosheets were then coassembled with DC anions into the DC intercalated LDH (DC-LDH) nanohybrids. The so-synthesized nanohybrids were characterized by XRD, TEM, FT-IR, elemental analyses and TG-DSC. It was found that the loading amount of DC in the nanohybrids could be easily controlled by changing the ratio of DC to LDH. In addition, the nanohybrids have similar characteristics with the DC-LDH nanohybrids synthesized by the hydrothermal method, including their DC loading, crystal structure, morphology and thermal gravimetric behavior. However, this strategy exhibited the advantages of short reaction time and mild experimental conditions compared with the hydrothermal method. - Graphical abstract: Deoxycholate intercalated layered double hydroxide nanohybrids were successfully synthesized via a coassembly strategy. In this strategy, the interlayer spaces of LDHs can be efficiently used for the intercalation of guest species. - Highlights: • Deoxycholate intercalated layered double hydroxide nanohybrids were synthesized via a coassembly strategy. • This strategy exhibited the advantages of short time and mild conditions. • This strategy can enable organic species to be readily intercalated into the LDH galleries

Exploring Alkaline Stable Organic Cations for Polymer Hydroxide Exchange Membranes

Science.gov (United States)

2015-04-29

1   1.1.2   Proton exchange membrane fuel cells ( PEMFCs ) ......................... 3   1.1.3   Alkaline fuel cells (AFCs...160   xi LIST OF FIGURES Figure 1.1:   Schematic diagram of a PEMFC ...according to the type of electrolyte they use. Nowadays, there are six major types of fuel cells: proton-exchange membrane fuel cells ( PEMFCs ), hydroxide

Impact analysis of calcium hydroxide on the juveniles of the river ...

African Journals Online (AJOL)

The use of inorganic chemicals to boost agro production has recently been extended to other environmental purposes. This study thus was carried out to assess the potential lethal impact of calcium hydroxide (Ca (OH)2) on aquatic environment using the brackish river prawn as the indicator organism. The prawns were ...

Poly I-lactide-layered double hydroxide nanocomposites via in situ polymerization of I-lactide

DEFF Research Database (Denmark)

Katiyar, Vimal; Gerds, N.; Koch, C.B.

2010-01-01

The use of clay nanofillers offers a potential route to improved barrier properties in polylactide films. Magnesium–aluminium layered double hydroxides (LDHs) are interesting in this respect and we therefore explored synthesis of PLA-LDH nanocomposites by ring-opening polymerization. This method ...... weight was significantly reduced when in-situ polymerization was conducted in the presence of the LDHs and we suggest that chain termination via LDH surface hydroxyl groups and/or metal-catalyzed degradation could be responsible.......The use of clay nanofillers offers a potential route to improved barrier properties in polylactide films. Magnesium–aluminium layered double hydroxides (LDHs) are interesting in this respect and we therefore explored synthesis of PLA-LDH nanocomposites by ring-opening polymerization. This method...

Effectiveness of Arsenic Co-Precipitation with Fe-Al Hydroxides for Treatment of Contaminated Water

Directory of Open Access Journals (Sweden)

Jaime Wilson Vargas de Mello

2018-03-01

Full Text Available ABSTRACT Wastewater treatment is a challenging problem faced by the mining industry, especially when mine effluents include acid mine drainage with elevated arsenic levels. Iron (hydroxides are known to be effective in removal of As from wastewater, and although the resulting compounds are relatively unstable, the presence of structural Al enhances their stability, particularly under reducing conditions. The purpose of this study was to assess the effectiveness of Al-Fe (hydroxide co-precipitates for the removal of As from wastewater and to assess the chemical stability of the products. Different Al-Fe (hydroxides were synthesized at room temperature from ferrous and aluminum salts using three different Fe:Al molar ratios (1:0.0, 1:0.3, and 1:0.7 and aged for 90 days (sulfate experiments or 120 days (chloride experiments in the presence of arsenic. At the end of the aging periods, the precipitated sludges were dried and characterized in order to evaluate their stability and therefore potential As mobility. All treatments were effective in reducing As levels in the water to below 10 µg L-1, but the presence of Al impaired the effectiveness of the treatment. Aluminum decreased the chemical stability of the precipitated sludge and hence its ability to retain As under natural environmental conditions.

Removal of nitrate from ammonium hydroxide solution containing organics by ion exchange method

International Nuclear Information System (INIS)

Venugopal Chetty, K.; Gamare, Jayashree S.; Vaidya, V.N.

2004-01-01

Removal of nitrate from ammonium hydroxide solution containing HMTA (hexamethyltetramine) and Urea was studied using indigenously available anion exchange resins. This type of waste is produced during nuclear fuel preparation by internal gelation process. The resins used are Tulsion A-27(MP) and Duolite A. 102D. The time of equilibration and capacity of the resins were determined from distribution ratios obtained by equilibrating resin with nitrate solution. The loading, washing and elution behavior of nitrate on these resins were studied using synthetic mixture having similar composition of the waste produced. Elution studies were carried out using sodium hydroxide, hydrochloric acid and ammonium chloride. The studies were also carried out at higher temperature of around 60 degC. The data was compared with that obtained using Dowex 1x4 for the same purpose. (author)

Synthesis and properties of Mg2Al layered double hydroxides containing 5-fluorouracil

International Nuclear Information System (INIS)

Wang Zhongliang; Wang Enbo; Gao Lei; Xu Lin

2005-01-01

A pharmaceutically active compound, 5-fluorouracil (5-FU) has been firstly intercalated into layered double hydroxide with the restructure method. Powder X-ray diffraction and spectroscopic analysis indicate that 5-FU molecule is stabilized in the host interlayer by electrostatic interaction and intermolecular interaction, and that the orientation of 5-FU is different when changing the pattern of aging treatment or the swelling agent. The release studies show that a rapid release of the drug during the first 40min is followed by a more sustained one, and that the total amount of drug released from hybrid material into the aqueous solution is almost 87% and 74% at pH 4 and 7, respectively. The studies mentioned above suggest that layered double hydroxide might be used as the basis of a tunable drug delivery carrier

Calcium Hydroxide-induced Proliferation, Migration, Osteogenic Differentiation, and Mineralization via the Mitogen-activated Protein Kinase Pathway in Human Dental Pulp Stem Cells.

Science.gov (United States)

Chen, Luoping; Zheng, Lisha; Jiang, Jingyi; Gui, Jinpeng; Zhang, Lingyu; Huang, Yan; Chen, Xiaofang; Ji, Jing; Fan, Yubo

2016-09-01

Calcium hydroxide has been extensively used as the gold standard for direct pulp capping in clinical dentistry. It induces proliferation, migration, and mineralization in dental pulp stem cells (DPSCs), but the underlying mechanisms are still unclear. The aim of this study was to investigate the role of the mitogen-activated protein (MAP) kinase pathway in calcium hydroxide-induced proliferation, migration, osteogenic differentiation, and mineralization in human DPSCs. Human DPSCs between passages 3 and 6 were used. DPSCs were preincubated with inhibitors of MAP kinases and cultured with calcium hydroxide. The phosphorylated MAP kinases were detected by Western blot analysis. Cell viability was analyzed via the methylthiazol tetrazolium assay. Cell migration was estimated using the wound healing assay. Alkaline phosphatase (ALP) expression was analyzed using the ALP staining assay. Mineralization was studied by alizarin red staining analysis. Calcium hydroxide significantly promoted the phosphorylation of the c-Jun N-terminal kinase (JNK), p38, and extracellular signal-regulated kinase. The inhibition of JNK and p38 signaling abolished calcium hydroxide-induced proliferation of DPSCs. The inhibition of JNK, p38, and extracellular signal-regulated kinase signaling suppressed the migration, ALP expression, and mineralization of DPSCs. Our study showed that the MAP kinase pathway was involved in calcium hydroxide-induced proliferation, migration, osteogenic differentiation, and mineralization in human DPSCs. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Synthesis of Nickel and Nickel Hydroxide Nano powders by Simplified Chemical Reduction

International Nuclear Information System (INIS)

Tientong, J.; Garcia, S.; Thurber, C.R.; Golden, T.D.

2014-01-01

Nickel nano powders were synthesized by a chemical reduction of nickel ions with hydrazine hydrate at ph ∼ 12.5. Sonication of the solutions created a temperature of 54-65 °C to activate the reduction reaction of nickel nanoparticles. The solution ph affected the composition of the resulting nanoparticles. Nickel hydroxide nanoparticles were formed from an alkaline solution (ph ∼10) of nickel-hydrazine complexed by dropwise titration. X-ray diffraction of the powder and the analysis of the resulting Williamson-Hall plots revealed that the particle size of the powders ranged from 12 to 14 nm. Addition of polyvinylpyrrolidone into the synthesis decreased the nickel nanoparticle size to approximately 7 nm. Dynamic light scattering and scanning electron microscopy confirmed that the particles were in the nanometer range. The structure of the synthesized nickel and nickel hydroxide nanoparticles was identified by X-ray diffraction and Fourier transform infrared spectroscopy.

High efficient photocatalytic activity of Zn-Al-Ti layered double hydroxides nanocomposite

Directory of Open Access Journals (Sweden)

Amor F.

2018-01-01

Full Text Available This work establishes a simple method for synthesising layered double hydroxides (LDHs powders with coprecipitation. The characteristics of the samples were investigated y X-ray diffraction (XRD, scanning electron microscopy (SEM and spectrophotometer UV–Vis (DRS. Non-uniform distribution was shown for LDHs samples by SEM. Photocatalytic efficiencies were tested using methylene blue (MB dye as a model contaminant under UV irradiation. In particular, Zn–Al-Ti LDH exhibited an excellent performance towards MB degradation compared with commercial TiO2 nanoparticles. Methylene blue removal percentage was reached at almost 100%, whereas commercial TiO2 reached a removal rate of only 66% under the same conditions within 20 min. The aim of the current work is to prepare Zn-Al-Ti layered double hydroxides nanocomposite and to evaluate their photocatalytic activity in the removal of methylene blue under UV irradiation.

Real-time monitoring of arsenic filtration by granular ferric hydroxide

International Nuclear Information System (INIS)

Fleming, D.E.B.; Eddy, I.S.; Gherase, M.R.; Gibbons, M.K.; Gagnon, G.A.

2008-01-01

Full text: Contamination of drinking water by arsenic is a serious public health issue in many parts of the world. One recent approach to this problem has been to filter out arsenic by use of granular ferric hydroxide (GFH), an adsorbent developed specifically for the selective removal of arsenic from water. Previous studies have documented the efficiency and high treatment capacity of this approach. We present a novel X-ray fluorescence method to monitor the accumulation of arsenic within a specially designed GFH column, as both a function of time (or water volume) and location along the column. Using a miniature X-ray tube and silicon PiN diode detector, X-ray fluorescence is used to detect characteristic X-rays of arsenic excited from within the GFH. Trials were performed using a water flow rate of approximately 1.5 litres per hour, with an added arsenic concentration of approximately 1000 μg per litre. In this paper, trial results are presented and potential applications described. Characteristic arsenic Kα X-ray peak area as a function of time, as measured at various locations along a granular ferric hydroxide (GFH) water filtration column

An experiment using neutron activation analysis and a rare earth element to mark cotton plants and two insects that feed on them

Energy Technology Data Exchange (ETDEWEB)

Showler, Allan T. [USDA-ARS IFNRRU, Kika de la Garza Subtropical Agricultural Research Center, 2413 East Highway 83, Weslaco, TX 78596 (United States)]. E-mail: ashowler@weslaco.ars.usda.gov; James, William D. [Elemental Analysis Laboratory, 3144 Texas A and M University, College Station, TX 77843-3144 (United States); Armstrong, John S. [USDA-ARS BIRU, Kika de la Garza Subtropical Agricultural Research Center, 2413 East Highway 83, Weslaco, TX 78596 (United States); Westbrook, John K. [USDA-ARS APMRU, 2771 F and B Road, College Station, TX 77845-4966 (United States)

2006-08-15

Studies on insect dispersal and other behaviors can benefit from using markers that will not alter flight and fitness. Rare earth elements, such as samarium (Sm), have been used as ingested markers of some insects and detected using neutron activation analysis (NAA). In this study, samarium nitrate hexahydrate was mixed into artificial diet for boll weevils, Anthonomus grandis grandis Boheman (Coleoptera: Curculionidae), at different dosages and in water used to irrigate cotton, Gossypium hirsutum L. Samarium was detected in adult boll weevils fed on the samarium-labeled diet, but not after 5 or 10 days of being switched to non-labeled diet, even if the insects were given labeled diet for as long as 7 consecutive days. Introduced in irrigation water, 1% samarium (m/m) was detectable in cotton squares and leaf tissue. However, boll weevil adults fed samarium-labeled squares did not retain detectable levels of samarium, nor did boll weevil adults reared to adulthood from samarium-labeled squares. Fourth instar beet armyworms, Spodoptera exigua (Huebner) (Noctuidae: Lepidoptera), fed on samarium-labeled cotton leaves obtained enough samarium for NAA detection, but adult moths reared from them did not have detectable amounts of samarium. Although samarium can be useful as a marker when insects are presented with a continuous pulse of the label, elements that are assimilated by the insect would be more useful if a continuous infusion of the marker cannot be provided.

On calculation of dependence of ion sorption by oxides and hydroxides on ph of medium from logistic curve

International Nuclear Information System (INIS)

Artyukhin, P.I.

1988-01-01

Critical consideration of the earlier suggested method for calculation of dependences of relative sorption (S) of microcomponents (MC) with oxides and hydroxides on the pH solution by the so-called logistic curve is given, and it is concluded that the presented equation for the curve does not have properties of the logistic function and contradicts the experiment. The equation really describing the dependence of S on pH and complying with criteria imposed for logistic functions is shown to proceed from existing model representations on MC sorption with hydroxides, and this problem may be easily solved graphically by drawing the dependence lg (S/1-S)=A+mpH, where A-constant, m + -MC aqua-ion charge. The made conclusions are illustrated on the example of 14m In, 91 Y, 64 Cu coprecipitation with iron hydroxide

Double-blind, randomized, placebo-controlled trial of the use of topical 10% potassium hydroxide solution in the treatment of molluscum contagiosum.

Science.gov (United States)

Short, Katherine A; Fuller, L Claire; Higgins, Elisabeth M

2006-01-01

Molluscum contagiosum is a common viral infection of the skin that frequently affects children. Lesions take between 6 and 18 months to resolve spontaneously and are a source of great embarrassment to both caretakers and children, often affecting attendance at school and limiting social activity. Treatment options to date have been poorly tolerated by children but recent studies have suggested that potassium hydroxide may be beneficial. This double-blind, randomized, placebo-controlled study compared 10% potassium hydroxide with placebo (normal saline). Twenty patients, aged 2 to 12 years, were recruited. Parents applied a solution twice daily to lesional skin until signs of inflammation appeared. Children were examined by the same observer on days 0, 15, 30, 60, and 90. Seventy percent of children receiving topical potassium hydroxide cleared, compared with 20% in the placebo group. Further dosing studies are required to identify whether weaker concentrations of potassium hydroxide are as efficacious, with less irritancy.

Lithium adsorption on amorphous aluminum hydroxides and gibbsite

OpenAIRE

Prodromou, Konstantinos P.

2016-01-01

Lithium (Li) adsorption on both amorphous aluminum hydroxides and gibbsite was studied. For the amorphous Al(OH)3 the adsorption was found to be pH dependent. Generally, 1.6 times more Li was adsorbed at initial pH value 8.0 compared with pH value 6.50. Gibbsite adsorbed 11.6 to 45.5 times less Li quantities compared with amorphous Al(OH)3. Lithium adsorption was not depended on equilibrium times. It remained stable for all equilibrium times used. Lithium quantities extracted with 1N CH3COONH...

X-ray spectral analysis of niobium hydroxide

Energy Technology Data Exchange (ETDEWEB)

Khabeev, I.A.; Belkina, V.A.; Makarova, R.V.; Mel' nikova, R.A.; Smagunova, A.N.

1986-02-01

The authors have derived an x-ray method of determining Ta/sub 2/O/sub 5/, TiO/sub 2/, Fe/sub 2/O/sub 3/, Nb/sub 2/O/sub 5/, C1 and SiO2 with a KRF-18 quantometer. The method should provide accuracy in determining these elements characterized by relative derivations. The main components of niobium hydroxide were ground for improved determination. The method allows one to analyze a sample in 30 min. In a six hour working day, an assistant can analyze up to 25 samples. The time required for one sample in the chemical method is about 30 hours.

Chloride adsorption by calcined layered double hydroxides in hardened Portland cement paste

KAUST Repository

Yoon, Seyoon; Moon, Juhyuk; Bae, Sungchul; Duan, Xiaonan; Giannelis, Emmanuel P.; Monteiro, Paulo M.

2014-01-01

This study investigated the feasibility of using calcined layered double hydroxides (CLDHs) to prevent chloride-induced deterioration in reinforced concrete. CLDHs not only adsorbed chloride ions in aqueous solution with a memory effect but also had

Effect of monobutylether ethylene glycol on Mg/Al layered double hydroxide: a physicochemical and conductivity study

International Nuclear Information System (INIS)

Paulo, Maria Joao; Matos, Bruno Ribeiro de; Ntais, Spyridon; Coral Fonseca, Fabio; Tavares, Ana C.

2013-01-01

Mg–Al hydrotalcite-like compounds with OH − ions intercalated in the gallery and modified with monobutylether ethylene glycol (mbeeg) were prepared from Mg 6 Al 2 (CO 3 )(OH) 16 ·4H 2 O by the reconstruction method. The effect of the ethylene glycol, a moderate surfactant, on the textural properties and on the vapor water sorption of the layered double hydroxides was investigated by transmission electron microscopy and nitrogen and water sorption techniques. The ion conductivity of the samples was measured at 98 % RH up to 180 °C. The compounds are formed by nanoplatelets with a lateral size inferior to 20 nm. The addition of the ethylene glycol was found to increase the specific surface area, total pore volume, and water sorption capacity of the Mg–Al layered double hydroxide. However, it also decreased the average pore diameter, and the ion conductivity of the ethylene glycol modified layered double hydroxide was lower than expected based on the samples’ specific surface area and water content.

New layered double hydroxides by prepared by the intercalation of gibbsite

Energy Technology Data Exchange (ETDEWEB)

Rees, Jennifer R.; Burden, Chloe S.; Fogg, Andrew M., E-mail: andrewmfogg@hotmail.com

2015-04-15

New layered double hydroxides (LDHs) with the composition [MAl{sub 4}(OH){sub 12}]Cl{sub 2}·1.5H{sub 2}O (M=Co, Ni) have been prepared by reacting gibbsite, γ-Al(OH){sub 3}, with the appropriate chloride salt in a synthesis in which the water of crystallization is the only solvent present and fully characterized. These LDHs have been shown to undergo facile anion exchange reactions with both organic and inorganic anions at room temperature making them comparable to other LDHs in this respect. Reactions under the same conditions with CuCl{sub 2}·2H{sub 2}O and ZnCl{sub 2} failed to form the desired LDHs but those with nitrate salts did lead to the formation of the previously reported [MAl{sub 4}(OH){sub 12}](NO{sub 3}){sub 2}·1.5H{sub 2}O (M=Co, Ni) compounds. - Graphical abstract: New layered double hydroxides (LDHs) with the composition [MAl{sub 4}(OH){sub 12}]Cl{sub 2}·1.5H{sub 2}O (M=Co, Ni) have been prepared by reacting gibbsite, γ-Al(OH){sub 3}, with the appropriate chloride salt in a synthesis in which no additional solvent is used and fully characterized. These LDHs have been shown to undergo facile anion exchange reactions with both organic and inorganic anions at room temperature. - Highlights: • Synthesis of new layered double hydroxides, [MAl{sub 4}(OH){sub 12}]Cl{sub 2}·1.5H{sub 2}O (M=Co, Ni). • Demonstration of the anion exchange capacity with both organic and inorganic anions. • Demonstration of the generality of the synthesis for LDHs.

Fabrication and properties of samarium doped calcium sulphate thin films using spray pyrolysis technique

Energy Technology Data Exchange (ETDEWEB)

Reghima, Meriem [Université Tunis El Manar, Faculté des Sciences de Tunis, Département de Physique, LR99ES13 Laboratoire de Physique de la Matière Condensée (LPMC), 2092 Tunis, Tunisie (Tunisia); Institut d' Electronique et des systèmes, Unité Mixte de Recherche 5214 UM2-CNRS (ST2i) – Université Montpellier, 860 rue de Saint Priest, Bâtiment 5, 34097 Montpellier (France); Faculté des Sciences de Bizerte, Université de Carthage, Zarzouna 7021 (Tunisia); Guasch, Cathy [Institut d' Electronique et des systèmes, Unité Mixte de Recherche 5214 UM2-CNRS (ST2i) – Université Montpellier, 860 rue de Saint Priest, Bâtiment 5, 34097 Montpellier (France); Azzaza, Sonia; Alleg, Safia [Laboratoire de Magnétisme et Spectroscopie des Solides (LM2S), Département de Physique, Faculté des Sciences, Université Badji Mokhtar Annaba, B.P. 12, 23000 Annaba (Algeria); Kamoun-Turki, Najoua [Université Tunis El Manar, Faculté des Sciences de Tunis, Département de Physique, LR99ES13 Laboratoire de Physique de la Matière Condensée (LPMC), 2092 Tunis, Tunisie (Tunisia)

2016-10-01

Using low cost spray pyrolysis technique, polycrystalline CaSO{sub 4} thin films were successfully grown on a glass substrate with a thickness of about 1 μm. Samarium doping has been performed on CaSO{sub 4} thin films to explore luminescence properties. The characterizations of these films were carried out using X-ray diffraction, Scanning Electron Microscopy and optical measurements. The structural analyses reveal the existence of hexagonal CaSO{sub 4} phase with a (200) preferred orientation belonging to CaS compound for substrate temperatures below 350 °C. It is shown that the crystallinity of the sprayed thin films can be improved by increasing substrate temperature up to 250 °C. Warren-Averbach analysis has been applied on X-ray diffractogram to determine structural parameters involving the phase with its amount, the grain size and the lattice parameters using Maud software. The surface topography shows a rough surface covered by densely packed agglomerated clusters having faceted and hexagonal shapes. Energy dispersive microscopy measurements confirm the presence of calcium and sulfur in equal proportions as well as high percentage of oxygen. Photoluminescence at room temperature revealed that luminescence peaks are attributed to the intrinsic emission of pure CaSO{sub 4} phase. - Highlights: • Warren Averbach analysis reveal the presence of hcp structure of CaSO{sub 4} phase. • A mixture of CaSO{sub 4} and CaHO{sub 4.5}S phases has been detected for lower T{sub s}. • For increasing T{sub s}, the CaHO{sub 4.5}S phase has been disappeared. • The origin of PL peaks has been identified.

Samarium oxide as a radiotracer to evaluate the in vivo biodistribution of PLGA nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Mandiwana, Vusani, E-mail: VMandiwana@csir.co.za; Kalombo, Lonji, E-mail: LKalombo@csir.co.za [Centre of Polymers and Composites, CSIR (South Africa); Venter, Kobus, E-mail: Kobus.Venter@mrc.ac.za [South African Medical Research Council (South Africa); Sathekge, Mike, E-mail: Mike.Sathekge@up.ac.za [University of Pretoria and Steve Biko Academic Hospital, Department of Nuclear Medicine (South Africa); Grobler, Anne, E-mail: Anne.Grobler@nwu.ac.za; Zeevaart, Jan Rijn, E-mail: zeevaart@necsa.co.za [North-West University, DST/NWU Preclinical Drug Development Platform (South Africa)

2015-09-15

Developing nanoparticulate delivery systems that will allow easy movement and localization of a drug to the target tissue and provide more controlled release of the drug in vivo is a challenge in nanomedicine. The aim of this study was to evaluate the biodistribution of poly(d,l-lactide-co-glycolide) (PLGA) nanoparticles containing samarium-153 oxide ([{sup 153}Sm]Sm{sub 2}O{sub 3}) in vivo to prove that orally administered nanoparticles alter the biodistribution of a drug. These were then activated in a nuclear reactor to produce radioactive {sup 153}Sm-loaded-PLGA nanoparticles. The nanoparticles were characterized for size, zeta potential, and morphology. The nanoparticles were orally and intravenously (IV) administered to rats in order to trace their uptake through imaging and biodistribution studies. The {sup 153}Sm-loaded-PLGA nanoparticles had an average size of 281 ± 6.3 nm and a PDI average of 0.22. The zeta potential ranged between 5 and 20 mV. The [{sup 153}Sm]Sm{sub 2}O{sub 3} loaded PLGA nanoparticles, orally administered were distributed to most organs at low levels, indicating that there was absorption of nanoparticles. While the IV injected [{sup 153}Sm]Sm{sub 2}O{sub 3}-loaded PLGA nanoparticles exhibited the highest localization of nanoparticles in the spleen (8.63 %ID/g) and liver (3.07 %ID/g), confirming that nanoparticles are rapidly removed from the blood by the RES, leading to rapid uptake in the liver and spleen. From the biodistribution data obtained, it is clear that polymeric nanoscale delivery systems would be suitable for improving permeability and thus the bioavailability of therapeutic compounds.

Evaluation of the Magnesium Hydroxide Treatment Process for Stabilizing PFP Plutonium/Nitric Acid Solutions

Energy Technology Data Exchange (ETDEWEB)

Gerber, Mark A.; Schmidt, Andrew J.; Delegard, Calvin H.; Silvers, Kurt L.; Baker, Aaron B.; Gano, Susan R.; Thornton, Brenda M.

2000-09-28

This document summarizes an evaluation of the magnesium hydroxide [Mg(OH)2] process to be used at the Hanford Plutonium Finishing Plant (PFP) for stabilizing plutonium/nitric acid solutions to meet the goal of stabilizing the plutonium in an oxide form suitable for storage under DOE-STD-3013-99. During the treatment process, nitric acid solutions bearing plutonium nitrate are neutralized with Mg(OH)2 in an air sparge reactor. The resulting slurry, containing plutonium hydroxide, is filtered and calcined. The process evaluation included a literature review and extensive laboratory- and bench-scale testing. The testing was conducted using cerium as a surrogate for plutonium to identify and quantify the effects of key processing variables on processing time (primarily neutralization and filtration time) and calcined product properties.

Stepwise hydrochloric acid extraction of monazite hydroxides for the recovery of cerium lean rare earths, cerium, uranium and thorium

International Nuclear Information System (INIS)

Swaminathan, T.V.; Nair, V.R.; John, C.V.

1988-01-01

Monazite sand is normally processed by the caustic soda route to produce mixed rare earth chloride, thorium hydroxide and trisodium phosphate. Bulk of the mixed rare earth chloride is used for the preparation of FC catalysts. Recently some of the catalyst producers have shown preference to cerium depleted (lanthanum enriched) rare earth chloride rather than the natural rare earth chloride obtained from monazite. Therefore, a process for producing cerium depleted rare earth chloride, cerium, thorium and uranium from rare earth + thorium hydroxide obtained by treating monazite, based on stepwise hydrochloric acid extraction, was developed in the authors laboratory. The process involves drying of the mixed rare earth-thorium hydroxide cake obtained by monazite-caustic soda process followed by stepwise extraction of the dried cake with hydrochloric acid under specified conditions

Hydroxide precursors to produce nanometric YCrO{sub 3}: Characterization and conductivity analysis

Energy Technology Data Exchange (ETDEWEB)

Durán, A., E-mail: dural@cnyn.unam.mx [Universidad Nacional Autónoma de México, Centro de Nanociencias y Nanotecnología, Km. 107 Carretera Tijuana-Ensenada, Apartado Postal 14, C.P. 22800, Ensenada, B.C. (Mexico); Meza F, C. [Universidad Nacional Autónoma de México, Centro de Nanociencias y Nanotecnología, Km. 107 Carretera Tijuana-Ensenada, Apartado Postal 14, C.P. 22800, Ensenada, B.C. (Mexico); Arizaga, Gregorio Guadalupe Carbajal, E-mail: gregoriocarbajal@yahoo.com.mx [Departamento de Química, Universidad de Guadalajara, Marcelino García Barragán 1421, C.P. 44430, Guadalajara, Jalisco (Mexico)

2012-06-15

Highlights: ► Y/Cr mixed hydroxide was precipitated with gaseous ammonia. ► The hydroxide treated at 1373 K formed YCrO{sub 3} crystals with 20 nm diameter. ► Electrical properties were different than those found in other methods of synthesis. ► E{sub act} suggests small-polarons as conduction mechanisms. -- Abstract: A precursor to produce perovskite-type YCrO{sub 3} was precipitated by bubbling gaseous ammonia into an yttrium/chromium salts solution. X-ray diffraction showed that the as-prepared powders were amorphous. Thermal treatment between 1273 and 1373 K, leads to formation of polycrystalline YCrO{sub 3} with crystal sizes around 20 nm. High resolution X-ray photoelectron spectra showed uniform chemical environment for yttrium and chromium in the amorphous hydroxide and crystalline YCrO{sub 3}. Shifts between Y 3d{sub 5/2} and Cr 2p{sub 3/2} binding energy suggest redistribution or charge transfer between yttrium and chromium ions in the YCrO{sub 3} structure. The electrical properties of YCrO{sub 3}, whose precursors were precipitated with gaseous ammonia are different than those prepared by combustion synthesis. Electrical conductivity presents a sudden increase at ∼473 K, which is associated to the grain size and morphology of the crystallites. The redistribution of charge between Y(III) and Cr(III) is thermally activated by the hopping of small-polarons, which are characterized by the Arrhenius law as the conductive mechanism.

The effects of potassium and rubidium hydroxide on the alkali-silica reaction

International Nuclear Information System (INIS)

Shomglin, K.; Turanli, L.; Wenk, H.-R.; Monteiro, P.J.M.; Sposito, G.

2003-01-01

Expansion of mortar specimens prepared with an aggregate of mylonite from the Santa Rosa mylonite zone in southern California was studied to investigate the effect of different alkali ions on the alkali-silica reaction in concrete. The expansion tests indicate that mortar has a greater expansion when subjected to a sodium hydroxide bath than in a sodium-potassium-rubidium hydroxide bath. Electron probe microanalysis (EPMA) of mortar bars at early ages show that rubidium ions, used as tracer, were present throughout the sample by the third day of exposure. The analysis also shows a high concentration of rubidium in silica gel from mortar bars exposed to bath solutions containing rubidium. The results suggest that expansion of mortar bars using ASTM C 1260 does not depend on the diffusion of alkali ions. The results indicate that the expansion of alkali-silica gel depends on the type of alkali ions present. Alkali-silica gel containing rubidium shows a lower concentration of calcium, suggesting competition for the same sites

Nickel hydroxide ultrathin nanosheets as building blocks for electrochemically active layers

Czech Academy of Sciences Publication Activity Database

Schneiderová, Barbora; Demel, Jan; Pleštil, Josef; Janda, Pavel; Bohuslav, Jan; Ihiawakrim, D.; Ersen, O.; Rogez, G.; Lang, Kamil

2013-01-01

Roč. 1, č. 37 (2013), s. 11429-11437 ISSN 2050-7488 R&D Projects: GA ČR GAP207/10/1447; GA ČR GP13-09462P Institutional support: RVO:61388980 ; RVO:61389013 ; RVO:61388955 Keywords : layered hydroxide * delamination * nanosheet * batteries Subject RIV: CA - Inorganic Chemistry; CD - Macromolecular Chemistry (UMCH-V); CF - Physical ; Theoretical Chemistry (UFCH-W)

Porphyrin-layered double hydroxide/polymer composites as novel ecological photoactive surfaces

Czech Academy of Sciences Publication Activity Database

Káfuňková, Eva; Lang, Kamil; Kubát, Pavel; Klementová, Mariana; Mosinger, Jiří; Šlouf, Miroslav; Troutier-Thuilliez, A. L.; Leroux, F.; Verney, V.; Taviot-Guého, Ch.

2010-01-01

Roč. 20, č. 42 (2010), s. 9423-9432 ISSN 0959-9428 R&D Projects: GA ČR GAP207/10/1447 Institutional research plan: CEZ:AV0Z40320502; CEZ:AV0Z40400503; CEZ:AV0Z40500505 Keywords : porphyrins * nanoparticles * hydroxide/polymer composites Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 5.101, year: 2010

Fabrication of samarium strontium aluminate ceramic and deposition of thermal barrier coatings by air plasma spray process

Directory of Open Access Journals (Sweden)

Baskaran T

2018-01-01

Full Text Available Thermal barrier coatings (TBC with the metallic NiCrAlY bond coat are often used in many aircraft engines to protect superalloy components from high-temperature corrosion thereby to improve the life of gas turbine components. The search for new TBC material has been intensified in recent years due to lack of thermo-physical properties of conventionally used Yttria stabilized Zirconia (YSZ TBCs. Recently, the rare earth containing Samarium Strontium Aluminate (SSA based ceramic was proposed as a new TBC material due to its matching thermo-physical properties with the substrate. The present work focused on the synthesis of SSA ceramics for TBCs application and its coatings development on Ni-based superalloy Inconel 718 substrate by air plasma spray process. The X-ray photoelectron spectroscopy (XPS result confirmed the formation of single phase SSA ceramic after synthesis. The surface morphology of SSA TBCs is mainly composed of melted splats, semi and un-melted particles. The cross-sectional SEM micrographs did not show any spallation at the interface which indicated good mechanical interlocking between the bond coat and ceramic top coat. The Young’s modulus and hardness of SSA TBCs were found to be 80 and 6.1 GPa, respectively. The load-depth curve of SSA TBC showed good elastic recovery about 47 %.

Electrodialysis recovery of boric acid and potassium hydroxide from eluates of SWC facilities at NPP with VVER

International Nuclear Information System (INIS)

Dudnik, S.N.; Virich, P.M.; Kramskikh, E.Y.; Masanov, O.L.; Turovsky, I.P.

1993-01-01

To extract boric acid and potassium hydroxide from regenerates of SWC-2-46 facilities, an electrodialysis-sorption process has been devised consisting of the following operations: separation of boron-alkaline regenerate solution into desorbate and wash water; filling of desalination and concentration chambers, respectively, with desorbate and was water of electrodialysis equipment; production of boric acid and potassium hydroxide from desorbate by electrodialysis; removal of chloride-ion from boric acid solution on ion-exchange filter AB-17-18. The flow-sheet was tested and boron containing alkaline regeneration solutions were recovered from Novovoronezh NPP

Visible-light-enhanced interactions of hydrogen sulfide with composites of zinc (oxy)hydroxide with graphite oxide and graphene.

Science.gov (United States)

Seredych, Mykola; Mabayoje, Oluwaniyi; Bandosz, Teresa J

2012-01-17

Composites of zinc(oxy)hydroxide-graphite oxide and of zinc(oxy)hydroxide-graphene were used as adsorbents of hydrogen sulfide under ambient conditions. The initial and exhausted samples were characterized by XRD, FTIR, potentiometric titration, EDX, thermal analysis, and nitrogen adsorption. An increase in the amount of H(2)S adsorbed/oxidized on their surfaces in comparison with that of pure Zn(OH)(2) is linked to the structure of the composite, the relative number of terminal hydroxyls, and the kind of graphene-based phase used. Although terminal groups are activated by a photochemical process, the graphite oxide component owing to the chemical bonds with the zinc(oxy)hydroxide phase and conductive properties helps in electron transfer, leading to more efficient oxygen activation via the formation of superoxide ions. Elemental sulfur, zinc sulfide, sulfite, and sulfate are formed on the surface. The formation of sulfur compounds on the surface of zinc(oxy)hydroxide during the course of the breakthrough experiments and thus Zn(OH)(2)-ZnS heterojunctions can also contribute to the increased surface activity of our materials. The results show the superiority of graphite oxide in the formation of composites owing to its active surface chemistry and the possibility of interface bond formation, leading to an increase in the number of electron-transfer reactions. © 2011 American Chemical Society

Controlling electrodeposited ultrathin amorphous Fe hydroxides film on V-doped nickel sulfide nanowires as efficient electrocatalyst for water oxidation

Science.gov (United States)

Shang, Xiao; Yan, Kai-Li; Lu, Shan-Shan; Dong, Bin; Gao, Wen-Kun; Chi, Jing-Qi; Liu, Zi-Zhang; Chai, Yong-Ming; Liu, Chen-Guang

2017-09-01

Developing cost-effective electrocatalysts with both high activity and stability remains challenging for oxygen evolution reaction (OER) in water electrolysis. Herein, based on V-doped nickel sulfide nanowire on nickel foam (NiVS/NF), we further conduct controllable electrodeposition of Fe hydroxides film on NiVS/NF (eFe/NiVS/NF) to further improve OER performance and stability. For comparison, ultrafast chemical deposition of Fe hydroxides on NiVS/NF (uFe/NiVS/NF) is also utilized. V-doping of NiVS/NF may introduce more active sites for OER, and nanowire structure can expose abundant active sites and facilitate mass transport. Both of the two depositions generate amorphous Fe hydroxides film covering on the surface of nanowires and lead to enhanced OER activities. Furthermore, electrodeposition strategy realizes uniform Fe hydroxides film on eFe/NiVS/NF confirmed by superior OER activity of eFe/NiVS/NF than uFe/NiVS/NF with relatively enhanced stability. The OER activity of eFe/NiVS/NF depends on various electrodepositon time, and the optimal time (15 s) is obtained with maximum OER activity. Therefore, the controllable electrodeposition of Fe may provide an efficient and simple strategy to enhance the OER properties of electrocatalysts.

Effects of irrigation solutions and Calcium hydroxide dressing on root canal treatments of periapical lesions

Directory of Open Access Journals (Sweden)

Vita Nirmala

2006-03-01

Full Text Available The preparation of root canal in endodontic treatment plays an important role in treating non vital teeth with periapical lesion. Some factors influence the success of root canal treatment in short and long terms are the irrigation of root canal using antiseptic solution and the use of root canal medicament. The aim of this literature study is to determined the effect of irrigation solution and Calcium hydroxide dressing in root canal treatment of periapical lesions. The use of root canal medicament during the endodontic treatment could sterilized and decreased the number of pathogenic microorganism of root canal. An effective root canal irrigation solution must be able to dissolve organic and anorganic debris, lubricate endodontic instruments, disinfect microorganisms, non toxic and economical. The best irrigation solution has maximum antimicrobial effect with minimum toxicity. Division of calcium hydroxide into Calcium and hydroxyl ions is responsible for alkalinization of cavity, subsequently it makes the condition of cavity to be inappropriate for bacterial endotoxin in vitro as well as in vivo, and considered as the only clinically effective medicament in inactivating bacterial endotoxin. Calcium hydroxide is the only medication which has the ability to clinically inactive bacterial endotoxin in vitro in vivo and accepted as the best of root canal medication.

Ferric hydroxide supported gold subnano clusters or quantum dots: enhanced catalytic performance in chemoselective hydrogenation.

Science.gov (United States)

Liu, Lequan; Qiao, Botao; Ma, Yubo; Zhang, Juan; Deng, Youquan

2008-05-21

An attempt to prepare ferric hydroxide supported Au subnano clusters via modified co-precipitation without any calcination was made. High resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) have been employed to study the structure and chemical states of these catalysts. No Au species could be observed in the HRTEM image nor from the XRD pattern, suggesting that the sizes of the Au species in and on the ferric hydroxide support were less than or around 1 nm. Chemoselective hydrogenation of aromatic nitro compounds and alpha,beta-unsaturated aldehydes was selected as a probe reaction to examine the catalytic properties of this catalyst. Under the same reaction conditions, such as 100 degrees C and 1 MPa H2 in the hydrogenation of aromatic nitro compounds, a 96-99% conversion (except for 4-nitrobenzonitrile) with 99% selectivity was obtained over the ferric hydroxide supported Au catalyst, and the TOF values were 2-6 times higher than that of the corresponding ferric oxide supported catalyst with 3-5 nm size Au particles. For further evaluation of this Au catalyst in the hydrogenation of citral and cinnamaldehyde, selectivity towards unsaturated alcohols was 2-20 times higher than that of the corresponding ferric oxide Au catalyst.

Preparation and inhibition properties of molybdate intercalated ZnAlCe layered double hydroxide

Energy Technology Data Exchange (ETDEWEB)

Yan, Huajie; Wang, Jihui, E-mail: jhwang@tju.edu.cn; Zhang, Yu; Hu, Wenbin

2016-09-05

ZnAlCe layered double hydroxide intercalated by molybdate (ZnAlCe−MoO{sub 4} LDH) was successfully synthesized by using co-precipitation method, and the morphology, structure of ZnAlCe−MoO{sub 4} LDH were observed and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) techniques. The inhibition behavior of ZnAlCe−MoO{sub 4} LDH for Q235 steel in 3.5%NaCl solution was determined by polarization curves, electrochemical impedance spectroscopy (EIS), inductively coupled plasma mass spectrometer (ICP-MS) and X-ray photoelectron spectrometer (XPS) methods. The results shows that the synthesized ZnAlCe−MoO{sub 4} LDH has a lamellar structure with a particle size of 0.1–2.0 μm, an average thickness of 30 nm, and a basal plane spacing of 0.898 nm. Compared with the addition of ZnAl layered double hydroxide intercalated by nitrate (ZnAl−NO{sub 3} LDH) and ZnAl layered double hydroxide intercalated by molybdate (ZnAl−MoO{sub 4} LDH) in 3.5% NaCl solution, Q235 steel in 3.5%NaCl + ZnAlCe−MoO{sub 4} LDH solution has a lower corrosion current density, larger polarization resistance and a higher inhibition efficiency. The addition of ZnAlCe−MoO{sub 4} LDH will reduce the chloride concentration in 3.5% NaCl solution by the anion exchanged with molybdate, and improve the corrosion resistance of Q235 steel owing to the formation of passive film with the composition of ferrous or iron molybdate and deposition film with zinc and cerium hydroxides. - Highlights: • ZnAlCe−MoO{sub 4} LDH compound was successfully synthesized by co-precipitation method. • ZnAlCe−MoO{sub 4} LDH has a better inhibition effect to Q235 steel in 3.5%NaCl solution. • The Cl{sup −} ions in solution was partially exchanged with MoO{sub 4}{sup 2−} ions in host layers. • The passive film and deposition film were formed by the release of LDH compound.

Error causes in the determination of the acid-base reactivity of oxi-hydroxides

International Nuclear Information System (INIS)

Duc, M.; Lefevre, G.; Fedoroff, M.

2004-01-01

The long term safety of radioactive waste depositories is based on the sorption of radionuclides from underground water onto engineered and natural barriers. For a quantitative prediction of the migration in such barriers, we need accurate sorption data. Models should be in agreement with the sorption mechanism. Surface complexation is the most often used model for oxides and hydroxides. In fact, there are several types of surface complexation models such as 1-pK and 2-pK monosite, 1-pK and 2-pK multisite, pK-distribution models. Furthermore, there are several ways to describe the distribution of the electrostatic potential in the vicinity of the solid surface (CCM, DLM, BSM, TLM,..). However, all these models are based on the acid-base properties of superficial hydroxide or oxide groups of the solid. It is necessary to determine the surface charge versus pH (titration curves), the point of zero charge (pzc), the surface density of sites active towards protons and hydroxides in aqueous solutions, the acid-base constants of these sites. These parameters are then used for calculating the sorption constants of ions other than protons and hydroxide ions. It is therefore important to determine these parameters very accurately. A comparison of acid-base parameters published in the literature shows a large scatter for the ''same'' oxides [1,2]. Several causes could explain this scatter. One reason is the use of different models, each electrostatic models leading to different values of site density and constants. However, titration curves and pzc are independent of the model chosen. Another reason may be uncontrolled differences in the composition and purity of oxides. Finally, other causes could be found in the titration procedure, in the solubility and the stability of the solid. In order to understand more about the acid-base properties of oxides and about the origin of the discrepancies between measurements, we have performed a systematic experimental study of several

Coprecipitation of yttrium and aluminium hydroxide for preparation of yttrium aluminium garnet

NARCIS (Netherlands)

Vrolijk, J.W.G.A.; Willems, J.W.M.M.; Metselaar, R.

1990-01-01

Coprecipitation of yttrium and aluminium hydroxide for the preparation of pure yttrium aluminium garnet (YAG) powder with small grain size is the subject of this study. Starting materials are sulphates and chlorides of yttrium and aluminium. To obtain pure YAG (Y3Al5O12), the pH during flocculation

Aqueous Ammonia or Ammonium Hydroxide? Identifying a Base as Strong or Weak

Science.gov (United States)

Sanger, Michael J.; Danner, Matthew

2010-01-01

When grocery stores sell solutions of ammonia, they are labeled "ammonia"; however, when the same solution is purchased from chemical supply stores, they are labeled "ammonium hydroxide". The goal of this experiment is for students to determine which name is more appropriate. In this experiment, students use several different experimental methods…

The desorption of Phosphorous (32 P) fixed on iron and aluminum oxy-hydroxide surfaces by the soil microbial biomass

International Nuclear Information System (INIS)

Araujo, Lilian Maria Cesar de.

1995-02-01

This work determines whether the soil microbial biomass, with an ample supply of available C, can utilize P adsorber in the surfaces of oxy-hydroxides of Fe or Al of soil-P deficient soils. To simulate the surfaces of the natural Fe and Al compounds, synthetic oxy-hydroxides of Fe and Al, impregnated in strips of filter paper, and containing P tagged with 32 P, were used. (author). 60 refs., 7 figs., 7 tabs

Determination of soluble bromine in an extra-high-pressure mercury discharge lamp by sodium hydroxide decomposition-suppressed ion chromatography.

Science.gov (United States)

Mitsumata, Hiroshi; Mori, Toshio; Maeda, Tatsuo; Kita, Yoshiyuki; Kohatsu, Osamu

2006-02-01

We have established a simple method for assaying the quantity of soluble bromine in the discharge tubes of an extra-high-pressure mercury discharge lamp. Each discharge tube is destroyed in 5 ml of 10 mM sodium hydroxide, and the recovered sodium hydroxide solution is analyzed by suppressed-ion chromatography using gradient elution. We have clarified that this method can assay less than 1 microg of soluble bromine in a discharge tube.

Release behavior and toxicity profiles towards A549 cell lines of ciprofloxacin from its layered zinc hydroxide intercalation compound

OpenAIRE

Abdul Latip, Ahmad Faiz; Hussein, Mohd Zobir; Stanslas, Johnson; Wong, Charng Choon; Adnan, Rohana

2013-01-01

Background Layered hydroxides salts (LHS), a layered inorganic compound is gaining attention in a wide range of applications, particularly due to its unique anion exchange properties. In this work, layered zinc hydroxide nitrate (LZH), a family member of LHS was intercalated with anionic ciprofloxacin (CFX), a broad spectrum antibiotic via ion exchange in a mixture solution of water:ethanol. Results Powder x-ray diffraction (XRD), Fourier transform infrared (FTIR) and thermogravimetric analys...

Improving the quality of rice straw by urea and calcium hydroxide on rumen ecology, microbial protein synthesis in beef cattle.

Science.gov (United States)

Polyorach, S; Wanapat, M

2015-06-01

Four rumen-fistulated beef cattle were randomly assigned to four treatments according to a 4 × 4 Latin square design to study the influence of urea and calcium hydroxide [Ca(OH)2 ] treatment of rice straw to improve the nutritive value of rice straw. Four dietary treatments were as follows: untreated rice straw, 50 g/kg urea-treated rice straw, 20 g/kg urea + 20 g/kg calcium hydroxide-treated rice straw and 30 g/kg urea + 20 g/kg calcium hydroxide-treated rice straw. All animals were kept in individual pens and fed with concentrate at 0.5 g/kg of BW (DM), rice straw was fed ad libitum. The experiment was conducted for four periods, and each period lasted for 21 days. During the first 14 days, DM feed intake measurements were made while during the last 7 days, all cattle were moved to metabolism crates for total faeces and urine collections. The results revealed that 20 g/kg urea + 20 g/kg calcium hydroxide-treated rice straw improved the nutritive value of rice straw, in terms of dry matter intake, digestibility, ruminal volatile fatty acids, population of bacteria and fungi, nitrogen retention and microbial protein synthesis. Based on this study, it could be concluded that using urea plus calcium hydroxide was one alternative method to improve the nutritive value of rice straw, rumen ecology and fermentation and thus a reduction of treatment cost. Journal of Animal Physiology and Animal Nutrition © 2014 Blackwell Verlag GmbH.

Structural Investigation of Zn(II) Insertion in Bayerite, an Aluminum Hydroxide

DEFF Research Database (Denmark)

Pushparaj, Suraj Shiv Charan; Jensen, Nicholai Daugaard; Forano, Claude

2016-01-01

Bayerite was treated under hydrothermal conditions (120, 130, 140, and 150 °C) in order to prepare a series of layered double hydroxides (LDHs) with an ideal composition of ZnAl4(OH)12(SO4)0.5nH2O (ZnAl4-LDHs). These products were investigated by both bulk techniques (PXRD, TEM, and elemental an...

Removal of Lead Hydroxides Complexes from Solutions Formed in Silver/Gold: Cyanidation Process

Science.gov (United States)

Parga, José R.; Martinez, Raul Flores; Moreno, Hector; Gomes, Andrew Jewel; Cocke, David L.

2014-04-01

The presence of lead hydroxides in "pregnant cyanide solution" decreases the quality of the Dore obtained in the recovery processes of gold and silver, so it is convenient to remove them. The adsorbent capacity of the low cost cow bone powder was investigated for the removal of lead ions from a solution of lead hydroxide complexes at different initial metal ion concentrations (10 to 50 mg/L), and reaction time. Experiments were carried out in batches. The maximum sorption capacity of lead determined by the Langmuir model was found to be 126.58 mg/g, and the separation factor R L was between 0 and 1, indicating a significant affinity of bone for lead. Experimental data follow pseudo-second order kinetics suggesting chemisorption. It is concluded that cow bone powder can be successfully used for the removal of lead ions, and improves the quality of the silver-gold cyanides precipitate.

Effects of ammonium hydroxide on the structure and gas adsorption of nanosized Zr-MOFs (UiO-66).

Science.gov (United States)

Abid, Hussein Rasool; Ang, Ha Ming; Wang, Shaobin

2012-05-21

Several zirconium-based metal-organic frameworks (Zr-MOFs) have been synthesized using ammonium hydroxide as an additive in the synthesis process. Their physicochemical properties have been characterized by N(2) adsorption/desorption, XRD, SEM, FTIR, and TGA, and their application in CO(2) adsorption was evaluated. It was found that addition of ammonium hydroxide produced some effects on the structure and adsorption behavior of Zr-MOFs. The pore size and pore volume of Zr-MOFs were enhanced with the additive, however, specific surface area of Zr-MOFs was reduced. Using an ammonium hydroxide additive, the crystal size of Zr-MOF was reduced with increasing amount of the additive. All the samples presented strong thermal stability. Adsorption tests showed that capacity of CO(2) adsorption on the Zr-MOFs under standard conditions was reduced due to decreased micropore fractions. However, modified Zr-MOFs had significantly lower adsorption heat. The adsorption capacity of carbon dioxide was increased at high pressure, reaching 8.63 mmol g(-1) at 987 kPa for Zr-MOF-NH(4)-2.

A practical method for measuring the ion exchange capacity decrease of hydroxide exchange membranes during intrinsic degradation

Science.gov (United States)

Kreuer, Klaus-Dieter; Jannasch, Patric

2018-01-01

In this work we present a practical thermogravimetric method for quantifying the IEC (ion exchange capacity) decrease of hydroxide exchange membranes (HEMs) during intrinsic degradation mainly occurring through nucleophilic attack of the anion exchanging group by hydroxide ions. The method involves measuring weight changes under controlled temperature and relative humidity. These conditions are close to these in a fuel cell, i.e. the measured degradation rate includes all effects originating from the polymeric structure, the consumption of hydroxide ions and the release of water. In particular, this approach involves no added solvents or base, thereby avoiding inaccuracies that may arise in other methods due to the presence of solvents (other than water) or co-ions (such as Na+ or K+). We demonstrate the method by characterizing the decomposition of membranes consisting of poly(2,6-dimethyl-1,4-phenylene oxide) functionalized with trimethyl-pentyl-ammonium side chains. The decomposition rate is found to depend on temperature, relative humidity RH (controlling the hydration number λ) and the total water content (controlled by the actual IEC and RH).

A study of the electro-catalytic oxidation of methanol on a cobalt hydroxide modified glassy carbon electrode

International Nuclear Information System (INIS)

Jafarian, M.; Mahjani, M.G.; Heli, H.; Gobal, F.; Khajehsharifi, H.; Hamedi, M.H.

2003-01-01

Cobalt hydroxide modified glassy carbon electrodes (CHM/GC) prepared by the anodic deposition in presence of tartrate ions have been used for the electro-catalytic oxidation of methanol in alkaline solutions where the methods of cyclic voltammetery (CV), chronoamperometry (CA) and impedance spectroscopy (IS) have been employed. In CV studies, in the presence of methanol the peak current of the oxidation of cobalt hydroxide increase is followed by a decrease in the corresponding cathodic current. This suggests that the oxidation of methanol is being catalysed through the mediated electron transfer across the cobalt hydroxide layer comprising of cobalt ions of various valence states. A mechanism based on the electro-chemical generation of Co(IV) active sites and their subsequent consumptions by methanol have been discussed and the corresponding rate law under the control of charge transfer has been developed and kinetic parameters have been derived. In this context the charge transfer resistance accessible both theoretically and through the IS studies have been used as a criteria. Under the CA regimes the reaction followed a Cottrellian behaviour

Reduction kinetics of molecular nitrogen by niobium(3) hydroxide

International Nuclear Information System (INIS)

Denisov, N.T.; Shuvalova, N.I.; Shilov, A.E.

1987-01-01

Formation kinetics of hydrazine and ammonia durng nitrogen reduction by niobium(3) hydroxide at 284.5 - 334 K in water-methanol alkaline medium is studied. It is shown that the KOH concentration growth results in the rise of the N 2 H 4 formation rate and the decrease of the NH 3 formation rate. The sequence of reactions with respect to [Nb(3)] and [OH - ], as well as the value of activation energy of hydrazine formation of (50±4 kJ/mole) are determined

Aluminum Coprecipitates with Fe (hydr)oxides: Does Isomorphous Substitution of Al3plus for Fe3plus in Goethite Occur

Energy Technology Data Exchange (ETDEWEB)

E Bazilevskaya; D Archibald; M Aryanpour; J Kubicki; C Martinez

2011-12-31

Iron (hydr)oxides are common in natural environments and typically contain large amounts of impurities, presumably the result of coprecipitation processes. Coprecipitation of Al with Fe (hydr)oxides occurs, for example, during alternating reduction-oxidation cycles that promote dissolution of Fe from Fe-containing phases and its re-precipitation as Fe-Al (hydr)oxides. We used chemical and spectroscopic analyses to study the formation and transformation of Al coprecipitates with Fe (hydr)oxides. In addition, periodic density functional theory (DFT) computations were performed to assess the structural and energetic effects of isolated or clustered Al atoms at 8 and 25 mol% Al substitution in the goethite structure. Coprecipitates were synthesized by raising the pH of dilute homogeneous solutions containing a range of Fe and Al concentrations (100% Fe to 100% Al) to 5. The formation of ferrihydrite in initial suspensions with {<=}20 mol% Al, and of ferrihydrite and gibbsite in initial suspensions with {>=}25 mol% Al was confirmed by infrared spectroscopic and synchrotron-based X-ray diffraction analyses. While base titrations showed a buffer region that corresponded to the hydrolysis of Fe in initial solutions with {<=}25 mol% Al, all of the Al present in these solutions was retained by the solid phases at pH 5, thus indicating Al coprecipitation with the primary Fe hydroxide precipitate. In contrast, two buffer regions were observed in solutions with 30 mol% Al (at pH {approx}2.25 for Fe{sup 3+} and at pH {approx}4 for Al{sup 3+}), suggesting the formation of Fe and Al (hydr)oxides as two separate phases. The Al content of initial coprecipitates influenced the extent of ferrihydrite transformation and of its transformation products as indicated by the presence of goethite, hematite and/or ferrihydrite in aged suspensions. DFT experiments showed that: (i) optimized unit cell parameters for Al-substituted goethites (8 and 25 Mol% Al) in clustered arrangement (i.e., the

Pulp revascularization after root canal decontamination with calcium hydroxide and 2% chlorhexidine gel.

Science.gov (United States)

Soares, Adriana de Jesus; Lins, Fernanda Freitas; Nagata, Juliana Yuri; Gomes, Brenda Paula Figueiredo de Almeida; Zaia, Alexandre Augusto; Ferraz, Caio Cezar Randi; de Almeida, José Flávio Affonso; de Souza-Filho, Francisco José

2013-03-01

Pulp revascularization may be considered a promising alternative for necrotic immature teeth. Many studies have accomplished passive decontamination associated with an antibiotic paste. To date, there is no report evaluating calcium hydroxide associated with 2% chlorhexidine gel for revascularization therapy. The aim of this case report was to describe a new proposal for pulp revascularization with mechanical decontamination and intracanal medication composed of calcium hydroxide and 2% chlorhexidine gel. The patient, a 9-year-old girl, suffered an intrusion associated with pulp exposure caused by an enamel-dentin fracture in her maxillary left central incisor. After diagnosis, treatment consisted of revascularization therapy with gentle manual instrumentation of the cervical and medium thirds of the root in addition to intracanal medication with calcium hydroxide and 2% chlorhexidine gel for 21 days. In the second session, a blood clot was stimulated up to the cervical third of the root canal. Mineral trioxide aggregate (MTA; Angelus, Londrina, Paraná, Brazil) was used for cervical sealing of the canal. Coronal sealing was performed with temporary filling material and composite resin. During the follow-up period, the root canal space showed a progressive decrease in width, mineralized tissue deposition on root canal walls, and apical closure. A cone-beam computed tomography scan taken at the 2-year follow-up confirmed these findings and did not show complete root canal calcification. This new proposal for revascularization therapy with 2% chlorhexidine gel may be used for the treatment of necrotic immature root canals. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Theoretical investigation on the mechanism and dynamics of oxo exchange of neptunyl(VI) hydroxide in aqueous solution.

Science.gov (United States)

Yang, Xia; Chai, Zhifang; Wang, Dongqi

2015-03-21

Four types of reaction mechanisms for the oxo ligand exchange of monomeric and dimeric neptunyl(VI) hydroxide in aqueous solution were explored computationally using density functional theory (DFT) and ab initio classical molecular dynamics. The obtained results were compared with previous studies on the oxo exchange of uranyl hydroxide, as well as with experiments. It is found that the stable T-shaped [NpO3(OH)3](3-) intermediate is a key species for oxo exchange in the proton transfer in mononuclear Path I and binuclear Path IV, similar to the case of uranyl(VI) hydroxide. Path I is thought to be the preferred oxo exchange mechanism for neptunyl(VI) hydroxide in our calculations, due to the lower activation energy (22.7 and 13.1 kcal mol(-1) for ΔG(‡) and ΔH(‡), respectively) of the overall reaction. Path II via a cis-neptunyl structure assisted by a water molecule might be a competitive channel against Path I with a mononuclear mechanism, owing to a rapid dynamical process occurring in Path II. In Path IV with the binuclear mechanism, oxo exchange is accomplished via the interaction between [NpO2(OH)4](2-) and T-shaped [NpO3(OH)3](3-) with a low activation energy for the rate-determining step, however, the overall energy required to fulfill the reaction is slightly higher than that in mononuclear Path I, suggesting a possible binuclear process in the higher energy region. The chemical bonding evolution along the reaction pathways was discussed by using topological methodologies of the electron localization function (ELF).

Electron Beam Mediated Simple Synthetic Route to Preparing Layered Zinc Hydroxide

International Nuclear Information System (INIS)

Bae, Hyo Sun; Jung, Hyun

2012-01-01

We have developed a novel and eco-friendly synthetic route for the preparation of a two-dimensional layered zinc hydroxide with intercalated nitrate anions. The layered zinc hydroxide nitrate, called 'zinc basic salt', was, in general, successfully synthesized, using an electron beam irradiation technique. The 2-propanol solutions containing hydrated zinc nitrate were directly irradiated with an electron-beam at room temperature, under atmospheric conditions, without stabilizers or base molecules. Under electron beam irradiation, the reactive OH· radicals were generated by radiolysis of water molecules in precursor metal salts. After further radiolytic processes, the hydroxyl anions might be formed by the reaction of solvated electrons and the OH· radical. Finally, the Zn 5 (OH) 8 (NO 3 ) 2 ·2H 2 O was precipitated by the reaction of zinc cation and hydroxyl anions. Structure and morphology of obtained compounds were characterized by powder X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and high resolution transmission electron microscopy (HR-TEM). The chemical components of the products were determined by Fourier transform infrared spectroscopy (FT-IR) and elemental analysis (EA). The thermal behavior of products was studied by thermogravimetric (TG) and differential thermal analysis (DTA)

Chemically and compositionally modified solid solution disordered multiphase nickel hydroxide positive electrode for alkaline rechargeable electrochemical cells

Science.gov (United States)

Ovshinsky, Stanford R.; Corrigan, Dennis; Venkatesan, Srini; Young, Rosa; Fierro, Christian; Fetcenko, Michael A.

1994-01-01

A high capacity, long cycle life positive electrode for use in an alkaline rechargeable electrochemical cell comprising: a solid solution nickel hydroxide material having a multiphase structure that comprises at least one polycrystalline .gamma.-phase including a polycrystalline .gamma.-phase unit cell comprising spacedly disposed plates with at least one chemical modifier incorporated around the plates, the plates having a range of stable intersheet distances corresponding to a 2.sup.+ oxidation state and a 3.5.sup.+, or greater, oxidation state; and at least one compositional modifier incorporated into the solid solution nickel hydroxide material to promote the multiphase structure.

Preparation of poly(ethylene terephthalate/layered double hydroxide nanocomposites by in-situ polymerization and their thermal property

Directory of Open Access Journals (Sweden)

Q. Jiao

2012-06-01

Full Text Available Terephthalate (TA intercalated layered double hydroxides (LDHs were synthesized using hydroxides as raw materials, and poly(ethylene terephthalate (PET/LDH nanocomposites with different contents of TA intercalated LDHs were prepared by in-situ polymerization. The structure, morphology and thermal property of PET/LDH nanocomposites were investigated. The TA intercalated LDHs were partially exfoliated and well dispersed in PET matrix. The PET/LDH nanocomposites exhibit enhanced thermal stability relative to pure PET, confirmed by the thermogravimetric analysis results. The results of differential scanning calorimetry suggest that LDH nanoparticles could effectively promote the nucleation and crystallization of PET.

Statistical estimate of factors influence on sorption of Mo(Ⅵ) ions by tin hydroxide in dynamic conditions

International Nuclear Information System (INIS)

Parshutkin, V.V.; Granovskiy, Yu.V.; Prozorovskaya, Z.N.

1986-01-01

Present work is devoted to statistical estimate of factors influence on sorption of Mo(Ⅵ) ions by tin hydroxide in dynamic conditions. The influence of different factors on the process of sorption of Co(Ⅵ) ions by cryo-granular tin hydroxide in dynamic conditions is studied and optimal conditions of their extraction from aqueous solutions are considered. It is defined that factors significant affect the sorption process in dynamic conditions are: concentration of Mo(Ⅵ) ions in solution; the mass of sorbent; the rate of transmission of solution through the layer of sorbent; concentration of SO 4 2- ions in solution.

The effectiveness of samarium-153 (153Sm) lexidronam (EDTMP) in treatment of bone metastases

International Nuclear Information System (INIS)

Ma Yubo; Huang Gang; Liu Jianjun

2004-01-01

Objectives: To evaluate the effectiveness of samarium-153 (153Sm) lexidronam (EDTMP) in treatment of bone metastases. Methods: 380 patients with bone metastases were studied (221 men, 159 women; average age 65.3 y; ranged 27-91 y; average weight 59.3 kg, ranged 39-95 kg). The tumor types were prostate carcinoma (n=155), pulmonary carcinoma (n=92), breast cancer (n=57), gastric carcinoma (n=12), colorectal carcinoma (n=22), nasopharyngeal carcinoma (n=8), lymphoma (n=8), hepatic carcinoma (n=6), ovary carcinoma (n=4) and others (n=16). All patients were received 135Sm-EDTMP 0.8 or 1.0 mCi/kg during 1 to 7 course of treatment. Patients and physician evaluations were used to assess pain relief. Numbers of metastatic foci and activity of ROIs were used to observe post-therapy change in bone scanning. Results: In 380 patients, pain relief was observed in 257 patients (67.6%). Persistence of pain relief was seen through 2 to 24 weeks. The mean relief time is 5.8±3.4 weeks. KPS score was higher 10% than pre-therapy (71.2%±9.6% Vs 80.9%±10.3%, p<0.001). Numbers of metastatic foci (11.2+8.8 Vs 8.4±5.7, p<0.001) and activity of ROIs (3.28±2.04 Vs 2.15±0.94, p<0.01) were less than pre-therapy. Bone marrow suppression was mild and reversible (5.87±1.56 Vs 4.94±1.16 x 109/L). Conclusions: 153Sm-EDTMP provided relief of pain associated with bone metastases and inhibition of metastatic foci. As a relief drug of painful bone metastases, 153Sm-EDTMP is safe and effective. (authors)

Anion-exchange membranes derived from quaternized polysulfone and exfoliated layered double hydroxide for fuel cells

Energy Technology Data Exchange (ETDEWEB)

Liu, Wan; Liang, Na; Peng, Pai; Qu, Rong; Chen, Dongzhi; Zhang, Hongwei, E-mail: hanqiujiang@163.com

2017-02-15

Layered double hydroxides (LDH) are prepared by controlling urea assisted homogeneous precipitation conditions. Morphology and crystallinity of LDHs are confirmed by X-ray diffraction and scanning electron microscope. After LDHs are incorporated into quaternized polysulfone membranes, transmission electron microscope is used to observe the exfoliated morphology of LDH sheets in the membranes. The properties of the nanocomposite membranes, including water uptake, swelling ratio, mechanical property and ionic conductivity are investigated. The nanocomposite membrane containing 5% LDH sheets shows more balanced performances, exhibiting an ionic conductivity of 2.36×10{sup −2} S cm{sup −1} at 60 °C. - Graphical abstract: Anion-exchange membrane based on quaternized polysulfone and exfoliated layered double hydroxide is optically transparent and has good ionic properties.

New type ternary NiAlCe layered double hydroxide photocatalyst for efficient visible-light photoreduction of CO2 into CH4

Science.gov (United States)

Li, Ji; (Bill Yang, Y. J.

2018-02-01

New type of ternary NiAlCe layered double hydroxide photocatalyst was synthesized by a simple hydrothermal reaction. The obtained photocatalyst shows efficient visible-light activity for CO2 reduction to CH4. We have investigated the optimal Ce content in the catalyst and analyzed the mechanism by materials characterization. Additionally, a novel alkali etching method was used to construct the porous structure. The effect of the porosity and morphologies on the activity is investigated. It is found that the ternary NiAlCe layered double hydroxide photocatalyst with porosity showing the best photocatalytic activity among all the samples. Based on the characterization and first principle calculation, the detailed photocatalytic mechanism of the ternary NiAlCe layered double hydroxide photocatalyst is deduced.

Different arsenate and phosphate incorporation effects on the nucleation and growth of iron(III) (Hydr)oxides on quartz.

Science.gov (United States)

Neil, Chelsea W; Lee, Byeongdu; Jun, Young-Shin

2014-10-21

Iron(III) (hydr)oxides play an important role in the geochemical cycling of contaminants in natural and engineered aquatic systems. The ability of iron(III) (hydr)oxides to immobilize contaminants can be related to whether the precipitates form heterogeneously (e.g., at mineral surfaces) or homogeneously in solution. Utilizing grazing incidence small-angle X-ray scattering (GISAXS), we studied heterogeneous iron(III) (hydr)oxide nucleation and growth on quartz substrates for systems containing arsenate and phosphate anions. For the iron(III) only system, the radius of gyration (Rg) of heterogeneously formed precipitates grew from 1.5 to 2.5 (± 1.0) nm within 1 h. For the system containing 10(-5) M arsenate, Rg grew from 3.6 to 6.1 (± 0.5) nm, and for the system containing 10(-5) M phosphate, Rg grew from 2.0 to 4.0 (± 0.2) nm. While the systems containing these oxyanions had more growth, the system containing only iron(III) had the most nucleation events on substrates. Ex situ analyses of homogeneously and heterogeneously formed precipitates indicated that precipitates in the arsenate system had the highest water content and that oxyanions may bridge iron(III) hydroxide polymeric embryos to form a structure similar to ferric arsenate or ferric phosphate. These new findings are important because differences in nucleation and growth rates and particle sizes will impact the number of available reactive sites and the reactivity of newly formed particles toward aqueous contaminants.

Radiochemical investigation of the coprecipitation of microamounts of some hydrolyzable elements with metal hydroxides and metal oxides. Pt. 5

International Nuclear Information System (INIS)

Plotnikov, V.I.; Safonov, I.I.

1979-12-01

Investigation of the coprecipitation of various amounts of iron (III) (between 1 μg and 3.5 mg) with hydroxides of Sn(IV), Ga, Th, Sc, Be, Cd, and Mg as a function of the pH value of the solution. It is shown that the precipitation of the iron (III) with the precipitates of the hydroxides of Be, Cd, Ga, and Sc, which are of lower acidity compared with the microcomponent, is preceded by an acido-basic reaction of Fe(III) with the ions of the macrocomponent. The beginning of this reaction has been observed to coincide with the occurrence of its primary hydrolytical forms in the solution. It is furthermore intensified with decreasing difference in the acidic properties of iron (III) and the other element taking part in the reaction. The neutral hydroxide complex Fe(OH) 0 3 is shown to be the principal coprecipitated form of the iron (III). The coprecipitation of microquantities of iron (III) with tin (IV) hydroxide has been chosen as an example to illustrate the effect of additions of Th, Sc, and Be ions equimolar to the collector. The observed quantitative increase of the microcomponent in the solution is suggested to mainly result from the decrease of the hydrolytical degree of precipitation of tin (IV) due to the interaction of the latter with the ions of impurities. (orig.) 891 RSH/orig. 892 HIS [de

Porous layered double hydroxides synthesized using oxygen generated by decomposition of hydrogen peroxide

NARCIS (Netherlands)

Gonzalez Rodriguez, P.; de Ruiter, M.P.; Wijnands, Tom; ten Elshof, Johan E.

2017-01-01

Porous magnesium-aluminium layered double hydroxides (LDH) were prepared through intercalation and decomposition of hydrogen peroxide (H2O2). This process generates oxygen gas nano-bubbles that pierce holes in the layered structure of the material by local pressure build-up. The decomposition of the

Quantitative chemical state XPS analysis of first row transition metals, oxides and hydroxides

International Nuclear Information System (INIS)

Biesinger, M C; Payne, B P; McIntryre, N S; Hart, B R; Lau, L Wm; Grosvenor, A P; Smart, R StC

2008-01-01

Practical quantitative chemical state X-ray photoelectron spectroscopy (XPS) analysis of first row transition metals, oxides and hydroxides is challenging due to the complexity of their M 2p spectra. Complex multiplet splitting, shake-up and plasmon loss structure can play a role in the interpretation of the chemical states present. This paper will show practical curve fitting procedures for the quantitative measurement of different chemical states for metal oxides and hydroxides from a survey of transition metals. It will also discuss some of the limitations and pitfalls present as well as give practical examples of their successful use. These curve-fitting procedures are based on 1) standard spectra from quality reference samples, 2) a survey of appropriate literature databases and/or a compilation of literature references, 3) fitting of multiplet split spectra based on spectra of numerous reference materials and theoretical modelling, 4) spectral subtractions routines, again using reference spectra, and 5) specific literature references where fitting procedures are available

Quantitative chemical state XPS analysis of first row transition metals, oxides and hydroxides

Energy Technology Data Exchange (ETDEWEB)

Biesinger, M C; Payne, B P; McIntryre, N S [Department of Chemistry, University of Western Ontario, London, Ontario, N6A 5B7 (Canada); Hart, B R; Lau, L Wm [Surface Science Western, Room G1, Western Science Centre, University of Western Ontario, London, Ontario, N6A 5B7 (Canada); Grosvenor, A P [Department of Chemistry, Gunning/Lemieux Chemistry Centre, University of Alberta, Edmonton, Alberta, T6G 2G2 (Canada); Smart, R StC [ACeSSS, Applied Centre for Structural and Synchrotron Studies, University of South Australia, Mawson Lakes, SA 5095 (Australia)], E-mail: biesingr@uwo.ca

2008-03-15

Practical quantitative chemical state X-ray photoelectron spectroscopy (XPS) analysis of first row transition metals, oxides and hydroxides is challenging due to the complexity of their M 2p spectra. Complex multiplet splitting, shake-up and plasmon loss structure can play a role in the interpretation of the chemical states present. This paper will show practical curve fitting procedures for the quantitative measurement of different chemical states for metal oxides and hydroxides from a survey of transition metals. It will also discuss some of the limitations and pitfalls present as well as give practical examples of their successful use. These curve-fitting procedures are based on 1) standard spectra from quality reference samples, 2) a survey of appropriate literature databases and/or a compilation of literature references, 3) fitting of multiplet split spectra based on spectra of numerous reference materials and theoretical modelling, 4) spectral subtractions routines, again using reference spectra, and 5) specific literature references where fitting procedures are available.